WorldWideScience

Sample records for chain link statcom

  1. Modeling, control and simulation of a chain link STATCOM in EMTP-RV

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Nikunj M. [Siemens Energy and Automation, 100 Technology Drive, Alpharetta, GA 30005 (United States); Sood, Vijay K. [Faculty of Engineering and Applied Science, University of Ontario Institute of Technology (UOIT), Oshawa, ON L1H 7K4 (Canada); Ramachandran, V. [Department of Electrical and Computer Engineering, Concordia University, Montreal, QC H3G 1M8 (Canada)

    2009-03-15

    This paper describes an alternative STATic synchronous COMpensator (STATCOM), by connecting a number of gate turn off (GTO) thyristor converters in series on the ac side of the system. Each GTO converter forms one 'link' of a 1-phase, full-bridge voltage-source-converter (VSC) and is referred to as a 'Chain Link Converter' (CLC). Each GTO of a chain link STATCOM (CLS), is switched 'ON/OFF' only once per cycle of the fundamental frequency by using a sinusoidal pulse width modulation (SPWM) technique. Approximate models of a 3-phase CLS using dq-transformation are derived to design two controllers for controlling reactive current and ac voltage to stabilize the system voltage at the point of common coupling (PCC). A novel technique, called the rotated gate signal pattern (RGSP), is used for balancing the voltages of the link dc capacitors. The performance investigation of the CLS system when used in a radial line is carried out under steady- and transient-state operating conditions by means of the simulation package; EMTP-RV and the results are presented. (author)

  2. Impact of frequency modulation ratio on capacitor cells balancing in phase-shifted PWM based chain-link STATCOM

    DEFF Research Database (Denmark)

    Behrouzian, Ehsan; Bongiorno, Massimo; Teodorescu, Remus

    2014-01-01

    The purpose of this paper is to investigate the impact of switching harmonics on the instantaneous power that flows in the cells of a chain-link based STATCOM when using Phase-Shifted PWM. Two different cases are investigated for the converter cells: low, and high switching frequency. It is shown...

  3. Static compensators (STATCOMs) in power systems

    CERN Document Server

    Shahnia, Farhad; Ghosh, Arindam

    2014-01-01

    A static compensator (STATCOM), also known as static synchronous compensator, is a member of the flexible alternating current transmission system (FACTS) devices. It is a power-electronics based regulating device which is composed of a voltage source converter (VSC) and is shunt-connected to alternating current electricity transmission and distribution networks. The voltage source is created from a DC capacitor and the STATCOM can exchange reactive power with the network. It can also supply some active power to the network, if a DC source of power is connected across the capacitor. A STATCOM

  4. Integrated fuzzy-PI controlled current source converter based D-STATCOM

    Directory of Open Access Journals (Sweden)

    M. Deben Singh

    2016-12-01

    Full Text Available The distribution static synchronous compensator (D-STATCOM is a shunt-connected current injection custom power (CP device that can be used for improving quality and reliability of the power supplied to electric consumers under dynamic conditions of the distribution system. The CP devices such as dynamic voltage restorer and unified power quality conditioner including D-STATCOM are mostly designed and implemented using voltage source converter topology. The performance of D-STATCOM can be improved, if it is realized by using a current source converter topology which can generate a controllable current directly at its output terminals. Although the current source converter (CSC topology offers many promising advantageous features, not much research publications with CSC-based approach in the field of CP devices has been reported over the last one decade. This paper presents a novel method of realizing a D-STATCOM using CSC topology with an integrated fuzzy-PI controller for not only mitigating voltage sag but also capable of maintaining improved DC-link voltage profile. The model has been simulated in the MATLAB/SIMULINK environment. The simulation results under steady state and dynamic load perturbation provide excellent output characteristics that support the validity of the proposed model.

  5. Modeling of STATCOM under different loading conditions

    DEFF Research Database (Denmark)

    George, G.J.; Ramachandran, Rakesh; Kowsalya, M.

    2012-01-01

    This paper deals with the study and analysis of Flexible AC Transmission Systems (FACTS), mainly the modeling of STATCOM. Reactive Power Compensation plays a very important role in the transmission of Electric Power. A comparative study of how the reactive power is injected into the transmission ...

  6. Using variable DC sources in order to improve the voltage quality of a multilevel STATCOM with low frequency modulation

    DEFF Research Database (Denmark)

    Dowlatabadi, Mohammadkazem Bakhshizadeh; Najjar, Mohammad; Blaabjerg, Frede

    2016-01-01

    In this paper, a Selective Harmonic Elimination Pulse Width Modulation (SHE-PWM) method, which utilizes adjustable dc links, is presented for a Static Synchronous Compensator (STATCOM) based on Cascaded H-Bridge (CHB) multilevel converter. The proposed switching algorithm is able to fix...

  7. Smart — STATCOM control strategy implementation in wind power plants

    DEFF Research Database (Denmark)

    Sintamarean, Nicolae Christian; Cantarellas, Antoni Mir; Miranda, H.

    2012-01-01

    converters is increasing. This paper deals with an advanced control strategy design of a three-level converter performing STATCOM and Active Filter functionalities. The proposed system is called Smart-STATCOM since it has the capability of self-controlling reactive power and harmonic voltages at the same...

  8. Polymeric Nanoparticles via Noncovalent Cross-Linking of Linear Chains

    NARCIS (Netherlands)

    Seo, Myungeun; Beck, Benjamin J.; Paulusse, Jos Marie Johannes; Hawker, Craig J.; Kim, Sang Youl

    2008-01-01

    Novel polymeric nanoparticles were prepared through the chain collapse of linear polymers driven by noncovalent cross-linking of dendritic self-complementary hydrogen-bonding units (SHB). Random copolymers containing SHB units, poly[(methyl

  9. Analysis and design of virtual synchronous machine based STATCOM controller

    OpenAIRE

    Chi, Li; Burgos, R.; Cvetkovic, I.; Boroyevich, D.; Mili, L.; Rodríguez Cortés, Pedro

    2014-01-01

    this paper extends the virtual synchronous machine (VSM) concept, recently proposed as alternative means to synchronize grid-connected inverters, by developing a VSM-based STATCOM controller operating as synchronous condenser. To this end, a mathematical model is derived and used to analyze the inherent dynamics of the VSM-based STATCOM controller, which are then used to formulate design guidelines that further detach the proposed method from the perceived physical constraints introduced by t...

  10. Stress analysis of a link for slat chain conveyor

    Directory of Open Access Journals (Sweden)

    Tsonev Veselin

    2017-01-01

    Full Text Available This paper analyzes stresses in a link of a slat chain conveyor loaded with rock mass. Tensometric data and results from numerical simulation with Finite Element Method (FEM are used. The tensometric measurements are performed in real life conditions. For numerical simulation an adequate model with FEM has been created. The adequacy of the model is confirmed by the comparison of the experimental and numerical results. The factor of safety used in the design of the conveyor links is determined.

  11. Conformational Entropy of an Ideal Cross-Linking Polymer Chain.

    Science.gov (United States)

    Vorov, Oleg K; Livesay, Dennis R; Jacobs, Donald J

    2008-09-20

    We present a novel analytical method to calculate conformational entropy of ideal cross-linking polymers from the configuration integral by employing a Mayer series expansion. Mayer-functions describing chemical bonds within the chain and for cross-links are sharply peaked over the temperature range of interest, and, are well approximated as statistically weighted Dirac delta-functions that enforce distance constraints. All geometrical deformations consistent with a set of distance constraints are integrated over. Exact results for a contiguous series of connected loops are employed to substantiate the validity of a previous phenomenological distance constraint model that describes protein thermodynamics successfully based on network rigidity.

  12. Conformational Entropy of an Ideal Cross-Linking Polymer Chain

    Directory of Open Access Journals (Sweden)

    Donald J. Jacobs

    2008-09-01

    Full Text Available We present a novel analytical method to calculate conformational entropy of ideal cross-linking polymers from the configuration integral by employing a Mayer series expansion. Mayer-functions describing chemical bonds within the chain and for cross-links are sharply peaked over the temperature range of interest, and, are well approximated as statistically weighted Dirac delta-functions that enforce distance constraints. All geometrical deformations consistent with a set of distance constraints are integrated over. Exact results for a contiguous series of connected loops are employed to substantiate the validity of a previous phenomenological distance constraint model that describes protein thermodynamics successfully based on network rigidity.

  13. Using STATCOM to mitigate resonances in wind farms; Uso de STATCOM para atenuar ressonancias em parques eolicos

    Energy Technology Data Exchange (ETDEWEB)

    Bagnall, Trevor; Ritter, Carsten; Ronner, Beat; Maibach, Philippe; Butcher, Nick; Thurnherr, Tobias [ABB, Vasteras (Sweden)

    2010-12-15

    Resonance problems have been increasingly frequent in wind farms because of the increased capacitance of the cables in these facilities. This article presents the basic functions of a medium voltage STATCOM, installed in order to mitigate the resonance and contribute to meeting the reactive power requirements of the regulations of networks. Also discussed the theory of a control method for the purposes described.

  14. The missing links to link ubiquitin: Methods for the enzymatic production of polyubiquitin chains.

    Science.gov (United States)

    Faggiano, Serena; Alfano, Caterina; Pastore, Annalisa

    2016-01-01

    Attachment of ubiquitin (Ub) as monoUb and polyUb chains of different lengths and linkages to proteins plays a dominant role in very different regulatory mechanisms. Therefore, the study of polyUb chains has assumed a central interest in biochemistry and structural biology. An essential step necessary to allow in vitro biochemical and structural studies of polyUbs is the production of their chains in high quantities and purity. This is not always an easy task and can be achieved both enzymatically and chemically. Previous reviews have covered chemical cross-linking exhaustively. In this review, we concentrate on the different approaches developed so far for the enzymatic production of different Ub chains. These strategies permit a certain flexibility in the production of chains with various linkages and lengths. We critically describe the available methods and comment on advantages and limitations. It is clear that the field is mature to study most of the possible links, but some more work needs to be done to complete the picture and to exploit the current methodologies for understanding in full the Ub code. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  15. Linking of direct and compound chains in multistep nuclear reactions

    Science.gov (United States)

    Arbanas, G.; Chadwick, M. B.; Dietrich, F. S.; Kerman, A. K.

    1995-03-01

    We remove the sharp separation between multistep compound and multistep direct emission in the Feshbach-Kerman-Koonin (FKK) derivation of preequilibrium processes. In addition to the original multistep compound mechanism, we find a new class of multistep processes arising from linking of the direct and compound chains. There can be additional scatterings in unbound P space before the quasibound compound Q space is entered, or after it is left. We provide a theoretical justification for the presence of P-->Q transitions, which are needed to account for experimentally observed preequilibrium spectra. Our formalism is applied to the analysis of the 14 MeV 93Nb(n,n') reaction, using modified distorted-wave Born approximation (DWBA) matrix elements which include an inverse S-matrix factor. Since the dominant contribution to multistep compound emission comes from the 2p1h Q stage, the linking of the multistep chains results in flux bypassing this stage, resulting in a reduced multistep compound emission and an increased emission from the compound nucleus.

  16. Linking earth science informatics resources into uninterrupted digital value chains

    Science.gov (United States)

    Woodcock, Robert; Angreani, Rini; Cox, Simon; Fraser, Ryan; Golodoniuc, Pavel; Klump, Jens; Rankine, Terry; Robertson, Jess; Vote, Josh

    2015-04-01

    The CSIRO Mineral Resources Flagship was established to tackle medium- to long-term challenges facing the Australian mineral industry across the value chain from exploration and mining through mineral processing within the framework of an economically, environmentally and socially sustainable minerals industry. This broad portfolio demands collaboration and data exchange with a broad range of participants and data providers across government, research and industry. It is an ideal environment to link geoscience informatics platforms to application across the resource extraction industry and to unlock the value of data integration between traditionally discrete parts of the minerals digital value chain. Despite the potential benefits, data integration remains an elusive goal within research and industry. Many projects use only a subset of available data types in an integrated manner, often maintaining the traditional discipline-based data 'silos'. Integrating data across the entire minerals digital value chain is an expensive proposition involving multiple disciplines and, significantly, multiple data sources both internal and external to any single organisation. Differing vocabularies and data formats, along with access regimes to appropriate analysis software and equipment all hamper the sharing and exchange of information. AuScope has addressed the challenge of data exchange across organisations nationally, and established a national geosciences information infrastructure using open standards-based web services. Federated across a wide variety of organisations, the resulting infrastructure contains a wide variety of live and updated data types. The community data standards and infrastructure platforms that underpin AuScope provide important new datasets and multi-agency links independent of software and hardware differences. AuScope has thus created an infrastructure, a platform of technologies and the opportunity for new ways of working with and integrating

  17. Study on Compensation Control of STATCOM Based on MMC

    Directory of Open Access Journals (Sweden)

    Xie Yan

    2016-01-01

    Full Text Available This paper introduced modular multi-level converter (MMC, which could enhance the voltage and power level by sub-converter modules in series and was easy to extend to any level of output. Its structure and working mechanism were described. By analyzing the energy transfer performance of STATCOM based on MMC working conditions in the compensation, a comprehensive compensation control strategy was proposed based on direct current control mode. By analyzing the higher harmonic components circulation generated by the inconsistencies in the three-phase upper and lower arm voltage, a loop control strategy is proposed for the suppression of the circulation in the arms of the M-STATCOM. The simulation results show the strategy has a better tracking precision and response speed for the compensation control.

  18. Safe current injection strategies for a STATCOM under asymmetrical grid faults

    DEFF Research Database (Denmark)

    Rodriguez, Pedro; Medeiros, Gustavo; Luna, Alvaro

    2010-01-01

    This paper explores different strategies to set the reference current of a STATCOM under unbalanced grid voltage conditions and determines the maximum deliverable reactive power in each case to guarantee the injected current is permanently within the STATCOM secure operation limits. The paper pre...

  19. Control of STATCOM in wind power plants based on induction generators during asymmetrical grid faults

    DEFF Research Database (Denmark)

    Rodriguez, Pedro; Luna, Alvaro; Medeiros, G.

    2010-01-01

    This paper explores different strategies to set the reference current of a STATCOM under unbalanced grid voltage conditions. The aim of the proposed control strategies is to provide a set of reactive current references to be injected by the STATCOM under unbalanced grid faults. Their performance,...

  20. Transient Stability Enhancement of Multimachine Power System Using Robust and Novel Controller Based CSC-STATCOM

    Directory of Open Access Journals (Sweden)

    Sandeep Gupta

    2015-01-01

    Full Text Available A current source converter (CSC based static synchronous compensator (STATCOM is a shunt flexible AC transmission system (FACTS device, which has a vital role as a stability support for small and large transient instability in an interconnected power network. This paper investigates the impact of a novel and robust pole-shifting controller for CSC-STATCOM to improve the transient stability of the multimachine power system. The proposed algorithm utilizes CSC based STATCOM to supply reactive power to the test system to maintain the transient stability in the event of severe contingency. Firstly, modeling and pole-shifting controller design for CSC based STATCOM are stated. After that, we show the impact of the proposed method in the multimachine power system with different disturbances. Here, applicability of the proposed scheme is demonstrated through simulation in MATLAB and the simulation results show an improvement in the transient stability of multimachine power system with CSC-STATCOM. Also clearly shown, the robustness and effectiveness of CSC-STATCOM are better rather than other shunt FACTS devices (SVC and VSC-STATCOM by comparing the results in this paper.

  1. Phase Angle Control of Three Level Inverter Based D-STATCOM Using Neuro-Fuzzy Controller

    Directory of Open Access Journals (Sweden)

    COTELI, R.

    2012-02-01

    Full Text Available Distribution Static Compensator (D-STATCOM is a shunt compensation device used to improve electric power quality in distribution systems. It is well-known that D-STATCOM is a nonlinear, semi-defined and time-varying system. Therefore, control of D-STATCOM by the conventional control techniques is very difficult task. In this paper, the control of D-STATCOM is carried out by the neuro-fuzzy controller (NFC which has non-linear and robust structure. For this aim, an experimental setup based on three-level H-bridge inverter is constructed. Phase angle control method is used for control of D-STATCOM's output reactive power. Control algorithm for this experimental setup is prepared in MATLAB/Simulink and downloaded to DS1103 controller card. A Mamdani type NFC is designed for control of D-STATCOM's reactive current. Output of NFC is integrated to increase tracking performance of controller in steady state. The performance of D-STATCOM is experimentally evaluated by changing reference reactive current as on-line. The experimental results show that the proposed controller gives very satisfactory performance under different loading conditions.

  2. The Theoretical Power-factor Correction of a 3-phase Induction Motor using Customer STATCOM

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Su Saeng; Lee, Eun Woong; Choi, Jae Young [Chungnam National University (Korea); KIm, Hong Kwon [Korea Electric Power Corporation (Korea)

    2000-07-01

    This paper presents a novel power-factor correction method using customer STATCOM which generally improves the power quality of electric customers. Customer STATCOM detects the reactive currents of a induction motor(IM) and so injects compensation currents which is in 180.ded. phase with load currents that the reactive power of IM is compensated. In particular, the paper proposes the general compensation current references in the synchronous coordinate system and makes converter output voltages using space-vector PWM. The compensation effect of customer STATCOM is confirmed through the simulation according to the operation condition of an induction motor (at no load and full load). (author). refs., figs., tabs.

  3. Mitigation of Voltage Dip and Voltage Flickering by Multilevel D-STATCOM

    Directory of Open Access Journals (Sweden)

    M. S. Ballal

    2012-01-01

    Full Text Available The basic power quality problems in the distribution network are voltage sag (dip, voltage flickering, and the service interruptions. STATCOM is a Flexible AC Transmission Systems (FACTS technology device which can independently control the flow of reactive power. This paper presents the simulation and analysis of a STATCOM for voltage dip and voltage flickering mitigation. Simulations are carried out in MATLAB/Simulink to validate the performance of the STATCOM. A comparison between the six-pulse inverter and the five-level diode-clamped inverter is carried out for the performance of 66/11 KV distribution system.

  4. Comparison Study of Power System Small Signal Stability Improvement Using SSSC and STATCOM

    DEFF Research Database (Denmark)

    Hu, Weihao; Su, Chi; Fang, Jiakun

    2013-01-01

    A static synchronous series compensator (SSSC) has the ability to emulate a reactance in series with the connected transmission line. A static synchronous compensator (STATCOM) is able to provide the reactive power to an electricity network. When fed with some supplementary signals from...... the connected power system, both SSSC and STATCOM are able to participate in the power system inter-area oscillation damping by changing the compensated reactance or the provided reactive power. This paper analyses the influence of SSSC and STATCOM on power system small signal stability. The damping controller...

  5. The Proteasome Distinguishes between Heterotypic and Homotypic Lysine-11-Linked Polyubiquitin Chains

    Directory of Open Access Journals (Sweden)

    Guinevere L. Grice

    2015-07-01

    Full Text Available Proteasome-mediated degradation occurs with proteins principally modified with lysine-48 polyubiquitin chains. Whether the proteasome also can bind atypical ubiquitin chains, including those linked by lysine-11, has not been well established. This is critically important, as lysine-11 polyubiquitination has been implicated in both proteasome-mediated degradation and non-degradative outcomes. Here we demonstrate that pure homotypic lysine-11-linked chains do not bind strongly to the mammalian proteasome. By contrast, heterotypic polyubiquitin chains, containing lysine-11 and lysine-48 linkages, not only bind to the proteasome but also stimulate the proteasomal degradation of the cell-cycle regulator cyclin B1. Thus, while heterotypic lysine-11-linked chains facilitate proteasomal degradation, homotypic lysine-11 linkages adopt conformations that prevent association with the proteasome. Our data demonstrate the capacity of the proteasome to bind ubiquitin chains of distinct topology, with implications for the recognition and diverse biological functions of mixed ubiquitin chains.

  6. Corrosion analysis in mooring chain links; Analise de corrosao em elos de amarras

    Energy Technology Data Exchange (ETDEWEB)

    Leal, Silvia N.; Pereira, Marcos V. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Ciencia dos Materiais e Metalurgia; Costa, Luis C. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Motta, Sergio H. [Brasilamarras - Companhia Brasileira de Amarras, Niteroi, RJ (Brazil)

    2004-07-01

    The purpose of this work was to characterize the localized corrosion phenomenon in the weld region of offshore mooring chain links type ORQ. In this sense, a number of chain links were selected after finishing their projected life time without corrosion signs (chains without corrosion) as well as chain links which showed a reduced life time caused by localized corrosion (chains with corrosion). In the sequence, electrochemistry tests evaluated the corrosion susceptibility of the different regions of the weld joint. The results showed that the heat affected zone concerning the chains with corrosion was the anodic region, with high corrosion rate, while the same region on the not corroded chains was the cathodic one, with low corrosion rate. (author)

  7. Dynamic compensation of real and reactive power in wind farms using STATCOM

    Directory of Open Access Journals (Sweden)

    Shahzad Ahsan

    2016-09-01

    Full Text Available The dynamic stability of Squirrel Cage Induction Generators (SCIG based wind turbines may be improved by Static Synchronous Compensator (STATCOM. At the time of starting of wind farm and during short circuit fault the voltage of bus connecting the wind farm reduces drastically (Chen, 2005. A controller for the STATCOM has been developed with its capability to coordinate between the positive and the negative sequences of the grid voltage. This paper investigates effects of Squirrel Cage Induction Generator (SCIG in combination with a Static Synchronous Compensator (STATCOM under normal and during fault condition (Inwai et al., 2005. The results show that the STATCOM can regulate the fast changing voltage at the point of common coupling between the wind farm and the grid in normal and during fault condition. Also it can supply the active power during the short circuit fault condition.

  8. Enhanced control strategy for MMC-based STATCOM for unbalanced load compensation

    DEFF Research Database (Denmark)

    Nieves, M.; Maza, J.M.; Mauricio, J.M.

    2014-01-01

    Modular Multilevel Converters (MMC) technology is today one of the preferred technology in HVDC and large STATCOM applications due to modularity, fault tolerance and high efficiency, but the voltage balancing becomes very challenging, especially during negative sequence current injection as requi......Modular Multilevel Converters (MMC) technology is today one of the preferred technology in HVDC and large STATCOM applications due to modularity, fault tolerance and high efficiency, but the voltage balancing becomes very challenging, especially during negative sequence current injection...

  9. STATCOM – A Preface to Power Quality in Power Systems Performance

    Directory of Open Access Journals (Sweden)

    R. Jadeja

    2016-02-01

    Full Text Available This paper investigates different types of Flexible AC transmission System (FACTS controllers with focus on various operational and control aspects of static synchronous compensators (STATCOM to different performance characteristics like power transfer capability, voltage regulation, reactive power management, stability limits, power factor improvement etc. In addition, various features related to STATCOM like converter topologies, reference compensating signal generation schemes, controllers, and generation of switching signals are reviewed.

  10. Automatic external defibrillator: key link in the chain of survival

    NARCIS (Netherlands)

    Koster, Rudolph W.

    2002-01-01

    INTRODUCTION: Sudden cardiac death is a major health problem. Worldwide success of resuscitation from out-of-hospital cardiac arrest is modest, with 5% to 10% survival to hospital discharge. METHODS AND RESULTS: In the chain of survival, early defibrillation (goal <5 min after collapse) is a major

  11. Performance Analysis of Radial Distribution Systems with UPQC and D-STATCOM

    Science.gov (United States)

    Gupta, Atma Ram; Kumar, Ashwani

    2017-08-01

    This paper presents an effective method for finding optimum location of unified power quality conditioner (UPQC) and distributed static compensator (D-STATCOM) in radial distribution system. The bus having the minimum losses is selected as the candidate bus for UPQC placement and the optimal location of D-STATCOM is found by power loss index (PLI) method. The PLI values of all the buses are calculated and the bus having the highest PLI value is the most favorable bus and thus selected as candidate bus for D-STATCOM placement. Main contribution of this paper are: (i) finding optimum location of UPQC in radial distribution system (RDS) based on minimum power loss; (ii) finding the optimal size of UPQC which offers minimum losses; (iii) calculation of annual energy saving using UPQC and D-STATCOM; (iv) cost analysis with and without UPQC and D-STATCOM placement; and (v) comparison of results with and without UPQC and D-STATCOM placement in RDS. The algorithm is tested on IEEE 33-bus and 69-bus radial distribution systems by using MATLAB software.

  12. Sustainable Value Chains and Labour - Linking Chain and "Inner Drivers" : From Concepts to Practice

    NARCIS (Netherlands)

    L.J. Pegler (Lee)

    2011-01-01

    textabstractGlobal value chains are driven by considerations of cost and efficiency but just as much by power relations. This appears evident from studies of industrial relations and labour outcomes within value chains, especially those where drivenness is most explicit. Within a context of

  13. Links in the Chain: Bringing Together Literacy and Science

    Science.gov (United States)

    Taylor, Neil; Hansford, Diane; Rizk, Nadya; Taylor, Subhashni

    2017-01-01

    In Australia, the Federal Government and the Australian Academy of Science have developed a programme entitled "Primary Connections" (primaryconnections.org. au), aimed at supporting the teaching of science in the primary sector. The programme makes strong and explicit links between science and literacy through the use of word walls,…

  14. Low voltage ride through peformance of a STATCOM based on modular multilevel cascade converters for offshore wind application

    DEFF Research Database (Denmark)

    Tanaka, Takaaki; Wang, Huai; Ma, Ke

    2017-01-01

    Static Synchronous Compensators (STATCOMs) are being applied for offshore wind power plants to satisfy the grid codes under both normal operation and grid fault conditions. This paper investigates the performances of Modular Multilevel Cascade Converters (MMCC) for the STATCOM application, with s...

  15. Reactive power compensation capability of a STATCOM based on two types of Modular Multilevel Cascade Converters for offshore wind application

    DEFF Research Database (Denmark)

    Tanaka, Takaaki; Wang, Huai; Ma, Ke

    2017-01-01

    Static Synchronous Compensators (STATCOMs) have been applied for offshore wind power plants to satisfy the grid codes under both normal operation and grid fault conditions. This paper investigates the performances of two types of Modular Multilevel Cascade Converters (MMCC) for STATCOM applicatio...

  16. Application of PSAT to Load Flow Analysis with STATCOM under Load Increase Scenario and Line Contingencies

    Science.gov (United States)

    Telang, Aparna S.; Bedekar, P. P.

    2017-09-01

    Load flow analysis is the initial and essential step for any power system computation. It is required for choosing better options for power system expansion to meet with ever increasing load demand. Implementation of Flexible AC Transmission System (FACTS) device like STATCOM, in the load flow, which is having fast and very flexible control, is one of the important tasks for power system researchers. This paper presents a simple and systematic approach for steady state power flow calculations with FACTS controller, static synchronous compensator (STATCOM) using command line usage of MATLAB tool-power system analysis toolbox (PSAT). The complexity of MATLAB language programming increases due to incorporation of STATCOM in an existing Newton-Raphson load flow algorithm. Thus, the main contribution of this paper is to show how command line usage of user friendly MATLAB tool, PSAT, can extensively be used for quicker and wider interpretation of the results of load flow with STATCOM. The novelty of this paper lies in the method of applying the load increase pattern, where the active and reactive loads have been changed simultaneously at all the load buses under consideration for creating stressed conditions for load flow analysis with STATCOM. The performance have been evaluated on many standard IEEE test systems and the results for standard IEEE-30 bus system, IEEE-57 bus system, and IEEE-118 bus system are presented.

  17. Reactive Power Strategy of Cascaded Delta-connected STATCOM Under Asymmetrical Voltage Conditions

    DEFF Research Database (Denmark)

    He, Zhixing; Ma, Fujun; Xu, Qianming

    2017-01-01

    Cascaded static synchronous compensator (STATCOM) is an effective solution for reactive power support in mid-dle/high voltage conditions, and it has been widely employed to control reactive power in photovoltaic (PV) plants, wind farms, and industrial occasions. In this paper, reactive power...... control strategy of cascaded delta-connected STATCOM under asym-metrical voltage conditions is investigated. A new phase current reference calculation method is proposed to support reactive power continually under abnormal voltage conditions considering cluster voltage balancing control and phase current...... of the phase current references. Furthermore, the reactive power support capability of cascaded STATCOM under asymmetrical voltage conditions is explored and compared by combining the proposed references calculation method with the three generalized current references calculation strategies. Finally...

  18. Integral Sliding Mode Control Strategy of D-STATCOM for Unbalanced Load Compensation under Various Disturbances

    Directory of Open Access Journals (Sweden)

    Mingchao Xia

    2013-01-01

    Full Text Available Control strategies of D-STATCOM for unbalanced load compensation under internal and external disturbances were discussed. Linear control strategies do not have a satisfactory dynamic performance and become invalid under internal or external disturbances. To guarantee a good precision and robustness, a control strategy combining input-output feedback linearization technique with integral sliding mode control (ISMC method was applied to D-STATCOM for unbalanced load compensation. The strategy has features of simple structure and is easy to implement. A 10 MVar/10 kV D-STATCOM simulation system was built in PSCAD/EMTDC to verify the effectiveness and robustness of the control strategy proposed. Simulation results show that the control strategy can compensate reactive power and eliminate unbalance simultaneously under various disturbances.

  19. Coordinated Voltage Control Scheme for SEIG-Based Wind Park Utilizing Substation STATCOM and ULTC Transformer

    DEFF Research Database (Denmark)

    S. El Moursi, Mohamed; Bak-Jensen, Birgitte; Abdel-Rahman, Mansour Hassan

    2011-01-01

    and optimal tracking secondary voltage control for wind parks based on self-excited induction generators which comprise STATCOM and under-load tap changer (ULTC) substation transformers. The voltage controllers for the STATCOM and ULTC transformer are coordinated and ensure the voltage support. In steady...... of the short circuit ratio of the interconnection and the inherent communication delay between the wind park and the remote bus on the performance of the controllers and the maximum critical clearing time of fault are considered. Simulation results are presented to demonstrate the performance...

  20. A Study of Wind Farm Stabilization Using DFIG or STATCOM Considering Grid Requirements

    Directory of Open Access Journals (Sweden)

    K. E Okedu

    2010-01-01

    Full Text Available Recently, the grid codes require taking into account the reactive power of the wind farm in order to contribute to the networkstability, thus operating the wind farm as active compensator devices. This paper presents a comparative study of stabilizinga wind farm using (Doubly Fed Induction Generators DFIGs or using a (Static Synchronous Compensator STATCOM duringwind speed change and grid fault. Simulation results show that the wind farm could be effectively stabilized with bothsystems, but at a reduced cost with the DFIGs system because it can provide reactive power through its frequency converterswithout an external reactive power compensation unit like the STATCOM system significant.

  1. Voltage and frequency control of wind-powered islanded microgrids based on induction generator and STATCOM

    DEFF Research Database (Denmark)

    Bouzid, Allal; Sicard, Pierre; Guerrero, Josep M.

    2015-01-01

    This paper presents a comprehensive modeling of a three-phase cage induction machine used as a self-excited squirrel-cage induction generator (SEIG), and discusses the regulation of the voltage and frequency of a self-excited SEIG based on the action of the static synchronous Compensator (STATCOM......). The STATCOM with the proposed controller consists of a three-phase voltage-sourced inverter and a DC voltage. The compensator can provide the active and reactive powers and regulate AC system bus voltage and the frequency, but also may enhance the load stability. Moreover, a feed forward control method...

  2. Influence of reversible cross-link coordination on the mechanical behavior of a linear polymer chain

    Science.gov (United States)

    Shabbir, H.; Hartmann, M. A.

    2017-09-01

    In this work, we investigate the effect of the coordination of cross-links (i.e., the number of monomers participating in one cross-link) on the mechanical performance of a single polymeric chain. The framework provided by the reactive empirical bond order potential is used to generically describe the ability of certain monomers to form cross-links of different coordination. A systematic investigation of the influence of the coordination of cross-links on the mechanical properties of single polymeric chains is presented by comparing systems that contain cross-links in the classical form between two monomers (dimer) and such where the cross-links are formed by three monomers (trimer). The results show that the mechanical performance crucially depends on the coordination of cross-links. The overall shape of the load-displacement curves as well as mechanical parameters like stiffness, strength and work-to-straighten the molecule are different for the different systems. While the load-displacement curve shows an overall more continuous shape for the system containing trimers compared to the system including dimers only, the mechanical parameters are consistently lower for the first system. On the other hand, in contrast to the dimer case a trimer remains stable upon detachment of one of the monomers and the bonds are more mobile. This will be of importance in the case of fiber bundles, where the loading situation is even more complicated than in the single chain system due to the presence of inter-chain cross-links.

  3. A new assessment of the alleged link between element 115 and element 117 decay chains

    Science.gov (United States)

    Forsberg, U.; Rudolph, D.; Fahlander, C.; Golubev, P.; Sarmiento, L. G.; Åberg, S.; Block, M.; Düllmann, Ch. E.; Heßberger, F. P.; Kratz, J. V.; Yakushev, A.

    2016-09-01

    A novel rigorous statistical treatment is applied to available data (May 9, 2016) from search and spectroscopy experiments on the elements with atomic numbers Z = 115 and Z = 117. The present analysis implies that the hitherto proposed cross-reaction link between α-decay chains associated with the isotopes 293117 and 289115 is highly improbable.

  4. A new assessment of the alleged link between element 115 and element 117 decay chains

    OpenAIRE

    Forsberg, U.; Rudolph, D.; Fahlander, C; Golubev, P; Sarmiento, L. G.; Åberg, S.; Block, M; Düllmann, Ch. E.; Heßberger, F P; Kratz, J. V.; Yakushev, A

    2016-01-01

    A novel rigorous statistical treatment is applied to available data (May 9, 2016) from search and spectroscopy experiments on the elements with atomic numbers Z = 115 and Z = 117 . The present analysis implies that the hitherto proposed cross-reaction link between α-decay chains associated with the isotopes 293-117 and 289-115 is highly improbable.

  5. Linking theories of change and observed reality: the Shea value chain partnership case in Burkina

    NARCIS (Netherlands)

    Drost, S.; Wijk, van J.; Vellema, S.

    2012-01-01

    This case study found out how a public-private partnership in Burkina Faso helped female shea nut producers to link up with the cosmetic industry. Empirical data collected from October-December 2011 revealed that the shea value chain partnership between a international shea processing company, a

  6. Research on Improved Control Strategy for STATCOM Based on Virtual Matrix Method

    Directory of Open Access Journals (Sweden)

    Wang Xudong

    2016-01-01

    Full Text Available Fast and accurate detection of reactive current is the precondition for the realization of static synchronous compensator (STATCOM reactive power compensation and harmonic suppression. Aiming at deviation and delay of the traditional reactive current detection algorithm with phase-locked loop (PLL and low-pass filter (LPF of STATCOM, a novel improved reactive current detection algorithm without PLL is proposed, in which the virtual matrix (VM is built to replace the original PLL, and improved current average value filter is used to realize the function of LPF, so as to improve the real-time performance and robustness of reactive current detection. The realization process of VM detection method is derived in this paper, and improved control strategy for STATCOM is designed based on the VM detection method. Simulation analysis of the proposed detection algorithm and control strategy is conducted in Matlab platform so as to verify the correctness and effectiveness of the control strategy. The VM detection has the advantages of simple structure, fast response and easy for digital realization, which provides reference for the improvement of reactive power compensation precision for STATCOM.

  7. Optimal LQR controller in CSC based STATCOM using GA and PSO

    Directory of Open Access Journals (Sweden)

    Gupta Sandeep

    2014-09-01

    Full Text Available The static synchronous compensator (STATCOM is the multipurpose FACTS device with the multiple input and multiple output system for the enhancement of its dynamic performance in power system. Based on artificial intelligence (AI optimization technique, a novel controller is proposed for CSC based STATCOM. In this paper, the CSC based STATCOM is controlled by the LQR. But the best constant values for LQR controller's parameters are obtained laboriously through trial and error method, although time consuming. So the goal of this paper is to investigate the ability of AI techniques such as genetic algorithm (GA and particle swarm optimization (PSO methods to search the best values of LQR controller's parameters in a very short time with the desired criterion for the test system. Performances of the GA, PSO & ABC based LQR controllers are also compared. Applicability of the proposed scheme is demonstrated through simulation in MATLAB and the simulation results are shown an improvement in the input-output response of CSC-STATCOM

  8. Current source converter based D-STATCOM for voltage sag mitigation

    Directory of Open Access Journals (Sweden)

    Singh Moirangthem Deben

    2015-01-01

    Full Text Available This paper presents a novel method of realizing one of the custom power controllers, the distribution static synchronous compensator (D-STATCOM using current source converter (CSC topology. Almost all the custom power controllers such as dynamic voltage restorer (DVR, unified power quality conditioner (UPQC including D-STATCOM are generally designed and implemented by using voltage source converters (VSC and not much research publications with CSC based approach has been reported over the last one decade. Since the D-STATCOM is a current injection device, its performance can be improved when realized by a current-source converter which can generate a controllable current directly at its output terminals and offers many advantageous features. In this paper, an attempt has been made to study the performance of a CSC based D-STATCOM suitable for use in the power distribution system in order to mitigate voltage sag and improve power quality. The proposed model uses a three leg CSC whose switching strategy is based on sinusoidal pulse width modulation (SPWM. The model has been simulated in the Matlab/Simulink environment. The results of the simulation runs under steady state and dynamic load perturbation provide excellent voltage and current waveforms that support the justification of the proposed model.

  9. Internal Balance during Low-Voltage-Ride-Through of the Modular Multilevel Converter STATCOM

    NARCIS (Netherlands)

    Tsolaridis, Georgios; Kontos, E.; Chaudhary, Sanjay K.; Bauer, P.; Teodorescu, Remus

    2017-01-01

    Grid faults are common in power systems and can have a severe impact on the operation of the converters in the system. In this paper, the operation of a Modular Multilevel Converter (MMC)-based Static Synchronous Compensators (STATCOM) is investigated during grid faults. The study focuses on the

  10. Testing of a controller for an ETO-based STATCOM through controller hardware-in-the-loop simulation

    DEFF Research Database (Denmark)

    Langston, J.; Qi, L.; Steurer, M.

    2009-01-01

    a large-scale digital real time electromagnetic transients simulator. The STATCOM controller is interfaced to the simulation, providing firing pulses to the simulated STATCOM and receiving feedback of system voltages and currents. Notional wind speed data is used to simulate realistic behavior of the wind......The testing of a controller for a proposed 10 MVA STATCOM through hardware-in-the-loop experimentation is described in this paper. The electrical environment into which the STATCOM is to be inserted, including a significant portion of the utility network and a nearby wind farm are simulated using...... farm. This paper presents preliminary results of the ongoing testing of the controller under the most realistic system conditions. ©2009 IEEE....

  11. Design and Implementation of Flexible D-Statcom for Mitigating Power Quality Problems and Improve the Distribution System Performance

    National Research Council Canada - National Science Library

    Ramesh Lakavath; K.Kumaraswamy

    2014-01-01

    .... The performance of Flexible D-STATCOM system is to mitigate power quality problems and improve distribution system performance under all types of system related disturbances and system unbalanced...

  12. Design of a Three-Phase Statcom-Based Inductive Static VAR Compensator Using DC Capacitor Voltage Control Scheme

    OpenAIRE

    Abdulkareem Mokif Obais; Jagadeesh Pasupuleti

    2013-01-01

    In this study, a three-phase continuously controlled harmonic-free inductive static VAR compensator is presented. The compensator is built of a three-phase voltage source inverter based statcom. The phase currents of this compensator are linearly and continuously controlled by the statcom DC capacitor voltage. The control strategy is outlined by a process of forcing the capacitor voltage to follow a certain reference voltage which can be varied linearly from its maximum to its minimum values ...

  13. Fibrin chain cross-linking, fibrinolysis, and in vivo sealing efficacy of differently structured fibrin sealants.

    Science.gov (United States)

    Hedrich, Hans Christian; Simunek, Manuela; Reisinger, Sonja; Ferguson, James; Gulle, Heinz; Goppelt, Andreas; Redl, Heinz

    2012-08-01

    In this study, we compared the sealing characteristics and efficacy of a fibrin sealant with reduced plasminogen (FS-rplg) and a fibrin sealant with aprotinin as a fibrinolysis inhibitor (FS-apr). The relevant sealing characteristics including clot structure, fibrin chain cross-linking, and clot lysis were tested in the laboratory. The sealing efficacy was then investigated in a follow-up animal model to determine differences in the in vivo sealing properties. A total of 46 animals were available for the final analysis with 23 animals in each treatment arm. In conclusion, we saw differences in vitro between FS-rplg and FS-apr in ultrastructure and α-chain cross-linking rates as well as in the rate of fibrinolysis. These differences may explain the significantly enhanced sealing efficacy in FS-apr compared to FS-rplg shown in vivo in a rabbit intestinal model. Copyright © 2012 Wiley Periodicals, Inc.

  14. The Chain-Link Fence Model: A Framework for Creating Security Procedures

    OpenAIRE

    Houghton, Robert F.

    2013-01-01

    A long standing problem in information technology security is how to help reduce the security footprint. Many specific proposals exist to address specific problems in information technology security. Most information technology solutions need to be repeatable throughout the course of an information systems lifecycle. The Chain-Link Fence Model is a new model for creating and implementing information technology procedures. This model was validated by two different methods: the first being int...

  15. Carbamate-linked cationic lipids with different hydrocarbon chains for gene delivery.

    Science.gov (United States)

    Shi, Jia; Yu, Shijun; Zhu, Jie; Zhi, Defu; Zhao, Yinan; Cui, Shaohui; Zhang, Shubiao

    2016-05-01

    A series of carbamate-linked cationic lipids containing saturated or unsaturated hydrocarbon chains and quaternary ammonium head were designed and synthesized. After recrystallization, carbamate-linked cationic lipids with high purity (over 95%) were obtained. The structures of these lipids were proved by IR spectrum, HR-ESI-MS, HPLC, (1)H NMR and (13)C NMR. The liposomes were prepared by using these cationic lipids and neutral lipid DOPE. Particle size and zeta-potential were studied to show that they were suitable for gene transfection. The DNA-bonding ability of C12:0, C14:0 and C18:1 cationic liposomes was much better than others. The results of transfection showed that hydrophobic chains of these lipids have great effects on their transfection activity. The lipids bearing C12:0, C14:0 saturated chains or C18:1 unsaturated chain showed relatively higher transfection efficiency and lower cytotoxicity. So these cationic lipids could be used as non-viral gene carriers for further studies. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Comparison of Field Measurements and EMT Simulation Results on a Multi-Level STATCOM for Grid Integration of London Array Wind Power Plant

    DEFF Research Database (Denmark)

    Glasdam, Jakob; Kocewiak, Łukasz Hubert; Hjerrild, Jesper

    2014-01-01

    been acquired on a commercial ±50 MVAr state-of-the-art (SOA) MMCC STATCOM. The STATCOM is located at the point of common connection (PCC) at the world’s largest OWPP, London Array (LAOWPP). According to the authors’ knowledge, the presented paper will be the first of its kind to compare a detailed...... of the STATCOM for wind power integration, as well as of the validity of applying a generic model of the STATCOM without knowledge of the actual implemented control system. The proposed model is integrated into an aggregated EMT model of LAOWPP, which will be used to investigate possible resonance phenomena...

  17. The Optimization of Cyclic Links of Live Pig-Industry Chain Based on Circular Economics

    Directory of Open Access Journals (Sweden)

    Xing Liu

    2015-12-01

    Full Text Available To reduce waste and wastewater pollution and to improve the utilization rate of resources in the pig-industry chain, a circular economy of the chain can be developed. The key to constructing the circular economic system of the pig-industry chain is to determine the path of the cyclic materials and to design reasonable waste- and wastewater-treatment capacities. This paper focuses on the treatment and recycling of wastewater in the pig-industry chain and the treatment and recycling of waste into manure and feed. After giving the two circular paths, the paper proposes a multi-objective uncertainty-optimization model for the cyclic links of the pig-industry chain with the highest resource-reuse efficiency and the lowest construction cost based on the uncertainty of market demand. Using a combination of the neural network and genetic algorithm method for designing the solution process for the model, the paper finally introduces the determination methods of relevant parameters and verifies the feasibility and effectiveness of the model through a case study.

  18. Crystal structures of Lys-63-linked tri- and di-ubiquitin reveal a highly extended chain architecture.

    Science.gov (United States)

    Weeks, Stephen D; Grasty, Kimberly C; Hernandez-Cuebas, Lisa; Loll, Patrick J

    2009-12-01

    The covalent attachment of different types of poly-ubiquitin chains signal different outcomes for the proteins so targeted. For example, a protein modified with Lys-48-linked poly-ubiquitin chains is targeted for proteasomal degradation, whereas Lys-63-linked chains encode nondegradative signals. The structural features that enable these different types of chains to encode different signals have not yet been fully elucidated. We report here the X-ray crystal structures of Lys-63-linked tri- and di-ubiquitin at resolutions of 2.3 and 1.9 A, respectively. The tri- and di-ubiquitin species adopt essentially identical structures. In both instances, the ubiquitin chain assumes a highly extended conformation with a left-handed helical twist; the helical chain contains four ubiquitin monomers per turn and has a repeat length of approximately 110 A. Interestingly, Lys-48 ubiquitin chains also adopt a left-handed helical structure with a similar repeat length. However, the Lys-63 architecture is much more open than that of Lys-48 chains and exposes much more of the ubiquitin surface for potential recognition events. These new crystal structures are consistent with the results of solution studies of Lys-63 chain conformation, and reveal the structural basis for differential recognition of Lys-63 versus Lys-48 chains. 2009 Wiley-Liss, Inc.

  19. The Frequency Control in the islanded Micro Grid by using STATCOM Controllers

    Directory of Open Access Journals (Sweden)

    Ghulam Mustufa Bhutto

    2015-10-01

    Full Text Available When the distribution system is disconnected from the transmission system, the islanded portion of the network comprising DG (Distributed Generation units forms a MG (Micro Grid. It is essential either to shut down the DG units or ensure the stable and the controlled operation of the islanded MG. The frequency and the voltage of the islanded MG vary when it is isolated from the main transmission grid. The voltage and the frequency of the islanded MG can be controlled to the permissible limits by providing the required amount of the active and reactive power by the local available sources in the MG. The main focus of this paper is about the control of the network frequency in the islanded MG by employing PI controllers based STATCOM (Static Compensator and BESS-STATCOM (Battery Energy Storage System Equipped devices. The study is done by using DIgSILENT power factory software version 15.0

  20. Control of a Modular Multilevel Converter STATCOM under internal and external unbalances

    DEFF Research Database (Denmark)

    Tsolaridis, Georgios; Kontos, E.; Parikh, Harsh

    2016-01-01

    This paper develops a complete control scheme for the Modular Multilevel Converter (MMC) in a STATCOM application. The focus is laid on the internal balancing of the converter and its reliable operation under internal mismatches as well as under external unbalanced conditions. The leg energy...... and the simulation results verified the capability to provide maximum reactive power to the AC grid while maintaining internal balance through the individual control of each arm energy level....... controller ensures that the sum of the capacitor voltages of each phase are equal. An intuitive arm energy controller is also implemented which allows the decoupled control of the energy levels of every arm. The control performance of the STATCOM was evaluated under asymmetrical grid faults...

  1. Wind Power Plant Control Optimisation with Incorporation of Wind Turbines and STATCOMs

    DEFF Research Database (Denmark)

    Petersen, Lennart; Kryezi, Fitim; Iov, Florin

    2015-01-01

    This paper addresses a detailed design and tuning of a wind power plant slope voltage control with reactive power contribution of wind turbines and STATCOMS. First, small-signal models of a single wind turbine and the whole wind power plant are developed, being appropriate for voltage control...... assessment. An exemplary wind power plant located in the United Kingdom and the corresponding grid code requirements are used as a base case. The final design and tuning process of the voltage controller results in a guidance, proposed for this particular control architecture. It provides qualitative...... outcomes regarding the impact of system delays, grid conditions and various operating conditions of the wind power plant, with and without incorporation of STATCOMS....

  2. Mitigation of voltage dip and power system oscillations damping using dual STATCOM for grid connected DFIG

    Directory of Open Access Journals (Sweden)

    D.V.N. Ananth

    2017-12-01

    Full Text Available During grid fault, transmission lines reach its thermal limit and lose its capability to transfer. If this fault current enters generator terminals, it will lead to dip in stator voltage and consequently produces torque and real power oscillations. This further affects in the form of internal heat in rotor windings and finally damages the generator. A new control strategy is proposed to limit fault current using dual STATCOM, which will damp power oscillations and mitigate the voltage dip due to a severe symmetrical fault. It is achieved by diverting the fault current to the capacitor using the dual-STATCOM controller. It is best suitable to maintain power system stability with uninterrupted power supply, effective power transfer capability and rapid reactive power support and to damp inter-area oscillations. The effectiveness of SG and DFIG due to the transmission line short circuit symmetrical fault was studied.

  3. Synthesis and Catalytic Properties of Non-Cross-Linked and Cross-Linked Poly(alkylmethyldiallylammonium bromides) Having Decyl, Octyl, and Hexyl Side Chains

    NARCIS (Netherlands)

    Wang, G.J; Engberts, J.B.F.N.

    1995-01-01

    A family of non-cross-linked and cross-linked copolymers containing decyl, octyl, and hexyl groups as side chains ((CL)-CopolC1-10, (CL)-CopolC1-8, and (CL)-CopolC1-6, respectively) were synthesized by radical-initiated cyclocopolymerization of alkylmethyldiallylammonium bromide monomers without and

  4. Etude par simulation hil des performances d'un statcom pour la ...

    African Journals Online (AJOL)

    Ce travail présente l'étude par simulation Hardware In the Loop (HIL) des performances d'un STATCOM pour la stabilisation de la tension délivrée par une génératrice asynchrone triphasée auto excitée dans un réseau autonome. Nous avons combiné l'utilisation du logiciel de simulation LABVIEW et la carte ARDUINO ...

  5. Analysis of Enhancement in Available Power Transfer Capacity by STATCOM Integrated SMES by Numerical Simulation Studies

    DEFF Research Database (Denmark)

    Saraswathi, Ananthavel; Sanjeevikumar, Padmanaban; Shanmugham, Sutha

    2016-01-01

    Power system researches are mainly focused in enhancing the available power capacities of the existing transmission lines. But still, no prominent solutions have been made due to several factors that affect the transmission lines which include the length, aging of the cables and losses on generat...... independently between the transmission lines and STATCOM-(SMES) units. Complete proposed power system is implemented in numerical simulation software (Matlab/Simulink) and its performance is validated based on obtained investigation results....

  6. Controller Design of STATCOM for Power System Stability Improvement Using Honey Bee Mating Optimization

    Directory of Open Access Journals (Sweden)

    A. Safari

    2013-02-01

    Full Text Available Damping of low frequency electromechanical oscillations is very important for a safe system operation. The fast acting, of a static synchronous compensator (STATCOM which is capable of improving both steady state and dynamic performance permits newer approaches to system stabilization. This paper presents a novel methodology for tuning STATCOM based damping controller in order to enhance the damping of system low frequency oscillations. The design of STATCOM parameters are considered an optimization problem according to the time domain-based objective function solved by a Honey Bee Mating Optimization (HBMO algorithm that has a strong ability to find the most optimistic results. To validate the results accuracy, a comparison with Genetic Algorithm (GA has been made. The effectiveness of the proposed controller is demonstrated through nonlinear time-domain simulation and some performance indices studies over a wide range of loading conditions. The simulation study shows that the designed controller by HBMO performs better than GA in finding the solution. Moreover, the system performance analysis under different operating conditions shows that the φ based controller is superior to the C based controller.

  7. Fractional-order PI based STATCOM and UPFC controller to diminish subsynchronous resonance.

    Science.gov (United States)

    Koteswara Raju, D; Umre, Bhimrao S; Junghare, Anjali S; Thakre, Mohan P; Motamarri, Rambabu; Somu, Chaitanya

    2016-01-01

    This research article proposes a powerful fractional-order PI controller to mitigate the subsynchronous oscillations in turbine-generator shaft due to subsynchronous resonance (SSR) with flexible AC transmission system devices such as static synchronous compensator (STATCOM) and unified power flow controller (UPFC). The diminution of SSR is achieved by the raising of network damping at those frequencies which are proximate to the torsional mode frequency of the turbine-generator shaft. The increase of network damping is obtained with the injection of subsynchronous frequency component of current and both current and voltage into the line. The subsynchronous component of current and voltage are derived from the measured signal of the system and further the same amount of shunt current is injected with STATCOM and simultaneous injection of current and voltage with UPFC into the transmission line to make the subsynchronous current to zero which is the prime source of turbine shaft oscillations. The insertion and proper tuning of Fractional-order PI controller in the control scheme, the subsynchronous oscillations are reduced to 92 % in case of STATCOM and 98 % in case of UPFC as compared to without controller and 14 % as compared with the results of conventional PI controller. The IEEE first benchmark model has adopted for analyze the effectiveness and speed of the proposed control scheme using MATLAB-Simulink and the corresponding results illustrates the precision and robustness of the proposed controller.

  8. Topological Hopf and Chain Link Semimetal States and Their Application to Co2 Mn Ga

    Science.gov (United States)

    Chang, Guoqing; Xu, Su-Yang; Zhou, Xiaoting; Huang, Shin-Ming; Singh, Bahadur; Wang, Baokai; Belopolski, Ilya; Yin, Jiaxin; Zhang, Songtian; Bansil, Arun; Lin, Hsin; Hasan, M. Zahid

    2017-10-01

    Topological semimetals can be classified by the connectivity and dimensionality of the band crossings in momentum space. The band crossings of a Dirac, Weyl, or an unconventional fermion semimetal are zero-dimensional (0D) points, whereas the band crossings of a nodal-line semimetal are one-dimensional (1D) closed loops. Here we propose that the presence of perpendicular crystalline mirror planes can protect three-dimensional (3D) band crossings characterized by nontrivial links such as a Hopf link or a coupled chain, giving rise to a variety of new types of topological semimetals. We show that the nontrivial winding number protects topological surface states distinct from those in previously known topological semimetals with a vanishing spin-orbit interaction. We also show that these nontrivial links can be engineered by tuning the mirror eigenvalues associated with the perpendicular mirror planes. Using first-principles band structure calculations, we predict the ferromagnetic full Heusler compound Co2 MnGa as a candidate. Both Hopf link and chainlike bulk band crossings and unconventional topological surface states are identified.

  9. Linking Supply Chain Network Complexity to Interdependence and Risk-Assessment: Scale Development and Empirical Investigation

    Directory of Open Access Journals (Sweden)

    Samyadip Chakraborty

    2015-12-01

    Full Text Available Concepts like supply chain network complexity, interdependence and risk assessment have been prominently discussed directly and indirectly in management literature over past decades and plenty of frameworks and conceptual prescriptive research works have been published contributing towards building the body of knowledge. However previous studies often lacked quantification of the findings. Consequently, the need for suitable scales becomes prominent for measuring those constructs to empirically support the conceptualized relationships. This paper expands the understanding of supply chain network complexity (SCNC and also highlights its implications on interdependence (ID between the actors and risk assessment (RAS in transaction relationships. In doing so, SCNC and RAS are operationalized to understand how SCNC affects interdependence and risk assessment between the actors in the supply chain network. The contribution of this study lies in developing and validating multi-item scales for these constructs and empirically establishing the hypothesized relationships in the Indian context based on firm data collected using survey–based questionnaire. The methodology followed included structural equation modeling. The study findings indicate that SCNC had significant relationship with interdependence, which in turn significantly affected risk assessment. This study carries both academic and managerial implications and provides an empirically supported framework linking network complexity with the two key variables (ID and RAS, playing crucial roles in managerial decision making. This study contributes to the body of knowledge and aims at guiding managers in better understanding transaction relationships.

  10. Impact of PSS and STATCOM Devices to the Dynamic Performance of a Multi-Machine Power System

    Directory of Open Access Journals (Sweden)

    G. Shahgholian

    2017-12-01

    Full Text Available This paper studies the impact of leveraging both static syn­ch­ron­ous compensator (STATCOM and power system stabilizer (PSS on multi-machine power systems. Considering a sta­ndard IEEE 9-bus test power network, classic and intelligent controllers are applied to achieve the desirable system performance. Simulated tests show the usefulness of STATCOM on network power quality in terms of voltage profile. In addition, it is shown that it can significantly improve the damping oscillations of synchronous generator under normal and abnormal network conditions. As shown, the PSS also contributes to improving the synch­ron­o­u­s generator parameters. It is also observed that using intelligent controllers with STATCOM and PSS leads to a better perfor­ma­nc­e relative to the classic controllers.

  11. Experimental and Simulation Analysis for the Impact of a Two-Link Chain with Granular Matter

    Directory of Open Access Journals (Sweden)

    Eliza A. Banu

    2015-01-01

    Full Text Available The resistance force of the granular matter is modeled as a linear superposition of a static (quadratic depth-dependent resistance force and a dynamic (quadratic velocity-dependent frictional force. The impact is defined from the moment the end point of the system comes in contact with the granular matter surface until the vertical linear velocity of the end point is zero. The variables of interest are the final depth at the end of the penetration phase and the stopping time. The results for a two-link kinematic chain with two points of contact were compared to the results obtained by applying the resistance force formulation developed to corresponding CAD simulation models. The results revealed that the final displacement increases with initial velocity, while the stopping time decreases. The sensitivity to the initial velocity was studied and an improvement to the resistance force formulated as a result. A series of expressions are proposed for the resistance force coefficients.

  12. From strings to coils: Rotational dynamics of DNA-linked colloidal chains

    Science.gov (United States)

    Kuei, Steve; Garza, Burke; Biswal, Sibani Lisa

    2017-10-01

    We investigate the dynamical behavior of deformable filaments experimentally using a tunable model system consisting of linked paramagnetic colloidal particles, where the persistence length lp, the contour length lc, and the strength and frequency of the external driving force are controlled. We find that upon forcing by an external magnetic field, a variety of structural and conformational regimes exist. Depending on the competition of forces and torques on the chain, we see classic rigid rotator behavior, as well as dynamically rich wagging, coiling, and folding behavior. Through a combination of experiments, computational models, and theoretical calculations, we are able to observe, classify, and predict these dynamics as a function of the dimensionless Mason and magnetoelastic numbers.

  13. Aplicación del control inteligente en el amortiguamiento de oscilaciones usando FACTS (STATCOM y SVC)

    OpenAIRE

    Bedoya Londoño, Andrea

    2014-01-01

    En este trabajo se describe el desarrollo de un controlador de oscilaciones, tanto para el STATCOM como para el SVC, usando algunos métodos de control inteligente. Se presenta el desarrollo de un controlador difuso sintonizado con técnicas de optimización, tales como, AG, PSO y COA como una opción moderna que permite encontrar los mejores parámetros del control difuso aplicado a los dispositivos FACTS (STATCOM Y SVC), con el fin de lograr amortiguar las oscilaciones del sistema de potencia y ...

  14. Novel STATCOM Controller for Mitigating SSR and Damping Power System Oscillations in a Series Compensated Wind Parks

    DEFF Research Database (Denmark)

    Bak-Jensen, Birgitte; El-Moursi, M. S.; Abdel-Rahman, Mansour Hassan

    2010-01-01

    This paper addresses implementation issues associated with a novel damping control algorithm for a STATCOM in a series compensated wind park for mitigating SSR (subsynchronous resonance) and damping power system oscillations. The IEEE first benchmark model on subsynchronous resonance is adopted...... damping control loop for the STATCOM based on a novel design procedure of nonlinear optimization are developed to meet the damping torque in the range of critical torsional frequencies. The Intelligent Shaft Monitor (ISM) scheme with Synthesized Special Indicator Signals are developed and examined...... the SSR, damping the power system oscillation and enhancing the transient stability margin in response to different SCRs....

  15. Tailoring chain length and cross-link density in dielectric elastomer toward enhanced actuation strain

    Science.gov (United States)

    Zhang, Quan-Ping; Liu, Jun-Hua; Liu, Hai-Dong; Jia, Fei; Zhou, Yuan-Lin; Zheng, Jian

    2017-10-01

    Adding ceramic or conductive fillers into polymers for increasing permittivity is a direct and effective approach to enhance the actuation strain of dielectric elastomer actuators (DEAs). Unfortunately, the major dielectric loss caused by weak interfaces potentially harms the electro-mechanical stability and lifetime of DEAs. Here, we construct a desired macromolecular network with a long chain length and low cross-link density to reduce the elastic modulus of silicone elastomers. Selecting a high molecular weight of polymethylvinylsiloxane and a low dose of the cross-linker leads the soft but tough networks with rich entanglements, poor cross-links, and a low amount of defects. Then, a ductile material with low elastic modulus but high elongation at break is obtained. It accounts for much more excellent actuation strain of Hl in comparison to that of the other silicone elastomers. Importantly, without other fillers, the ultralow dielectric loss, conductivity, and firm networks possibly promote the electro-mechanical stability and lifetime for the DEA application.

  16. The influence of business conditions on supply chain information-sharing mechanisms : A study among supply chain links of SMEs

    NARCIS (Netherlands)

    Welker, Gera A.; van der Vaart, Taco; van Donk, Dirk Pieter

    The literature acknowledges that the type and the level of supply chain integration differ in various situations. This paper investigates the influence of business conditions on internal and external information sharing and the role of ICT in order processing, using a multi-case study among SMEs.

  17. A rigid disulfide-linked nitroxide side chain simplifies the quantitative analysis of PRE data

    Energy Technology Data Exchange (ETDEWEB)

    Fawzi, Nicolas L. [National Institutes of Health, Laboratory of Chemical Physics, National Institute of Diabetes and Digestive and Kidney Diseases (United States); Fleissner, Mark R. [University of California, Jules Stein Eye Institute and Department of Chemistry and Biochemistry (United States); Anthis, Nicholas J. [National Institutes of Health, Laboratory of Chemical Physics, National Institute of Diabetes and Digestive and Kidney Diseases (United States); Kalai, Tamas; Hideg, Kalman [University of Pecs, Institute of Organic and Medicinal Chemistry (Hungary); Hubbell, Wayne L., E-mail: hubbellw@jsei.ucla.edu [University of California, Jules Stein Eye Institute and Department of Chemistry and Biochemistry (United States); Clore, G. Marius, E-mail: mariusc@mail.nih.gov [National Institutes of Health, Laboratory of Chemical Physics, National Institute of Diabetes and Digestive and Kidney Diseases (United States)

    2011-09-15

    The measurement of {sup 1}H transverse paramagnetic relaxation enhancement (PRE) has been used in biomolecular systems to determine long-range distance restraints and to visualize sparsely-populated transient states. The intrinsic flexibility of most nitroxide and metal-chelating paramagnetic spin-labels, however, complicates the quantitative interpretation of PREs due to delocalization of the paramagnetic center. Here, we present a novel, disulfide-linked nitroxide spin label, R1p, as an alternative to these flexible labels for PRE studies. When introduced at solvent-exposed {alpha}-helical positions in two model proteins, calmodulin (CaM) and T4 lysozyme (T4L), EPR measurements show that the R1p side chain exhibits dramatically reduced internal motion compared to the commonly used R1 spin label (generated by reacting cysteine with the spin labeling compound often referred to as MTSL). Further, only a single nitroxide position is necessary to account for the PREs arising from CaM S17R1p, while an ensemble comprising multiple conformations is necessary for those observed for CaM S17R1. Together, these observations suggest that the nitroxide adopts a single, fixed position when R1p is placed at solvent-exposed {alpha}-helical positions, greatly simplifying the interpretation of PRE data by removing the need to account for the intrinsic flexibility of the spin label.

  18. Quarterly Regional GDP Flash Estimates by Means of Benchmarking and Chain Linking

    Directory of Open Access Journals (Sweden)

    Cuevas Ángel

    2015-12-01

    Full Text Available In this article we propose a methodology for estimating the GDP of a country’s different regions, providing quarterly profiles for the annual official observed data. Thus the article offers a new instrument for short-term monitoring that allows the analysts to quantify the degree of synchronicity among regional business cycles. Technically, we combine time-series models with benchmarking methods to process short-term quarterly indicators and to estimate quarterly regional GDPs ensuring their temporal and transversal consistency with the National Accounts data. The methodology addresses the issue of nonadditivity, explicitly taking into account the transversal constraints imposed by the chain-linked volume indexes used by the National Accounts, and provides an efficient combination of structural as well as short-term information. The methodology is illustrated by an application to the Spanish economy, providing real-time quarterly GDP estimates, that is, with a minimum compilation delay with respect to the national quarterly GDP. The estimated quarterly data are used to assess the existence of cycles shared among the Spanish regions.

  19. Detection of Chlamydia trachomatis in endocervical specimens by an enzyme-linked polymerase chain reaction assay

    Directory of Open Access Journals (Sweden)

    Hashemi F.B.

    2007-05-01

    Full Text Available Chlamydia trachomatis (CT is the most common cause of sexually transmitted infections (STI worldwide and its early detection and treatment can reduces the high morbidity associated with this infection. In this study a sensitive diagnostic polymerase chain reaction (PCR-based enzyme immunoassay (PCR-EIA method was developed which detects CT in women with cervicitis. Endocervical swabs collected from 123 women (20-55 years with cervicitis were tested by both conventional PCR, and PCR-EIA assays, using identical sets of primers to amplify a CT-specific plasmid. For the conventional PCR, amplicons were detected by agarose gel electrophoretic analysis and the PCR-EIA assay used biotin-labeled primers, strepavidin-coated plates, a digoxigenin-labeled probe, and a final enzyme-linked colorometric analysis (405 nm was used to measure the CT amplicon. The frequency of positive CT infection by conventional PCR and PCR-EIA assay was 7% and 17%, respectively. The highest frequencies of CT infection were among women of 31-40 years old group (25%. The PCR-EIA limit of detection, calculated by linear regression analysis, was10 pg of CT DNA (r2=0.9642. The degree of agreement (Kappa between the conventional PCR and PCR-EIA method was 0.556 (p<0.0001.

  20. Adaptive Modulation for DFIG and STATCOM With High-Voltage Direct Current Transmission.

    Science.gov (United States)

    Tang, Yufei; He, Haibo; Ni, Zhen; Wen, Jinyu; Huang, Tingwen

    2016-08-01

    This paper develops an adaptive modulation approach for power system control based on the approximate/adaptive dynamic programming method, namely, the goal representation heuristic dynamic programming (GrHDP). In particular, we focus on the fault recovery problem of a doubly fed induction generator (DFIG)-based wind farm and a static synchronous compensator (STATCOM) with high-voltage direct current (HVDC) transmission. In this design, the online GrHDP-based controller provides three adaptive supplementary control signals to the DFIG controller, STATCOM controller, and HVDC rectifier controller, respectively. The mechanism is to observe the system states and their derivatives and then provides supplementary control to the plant according to the utility function. With the GrHDP design, the controller can adaptively develop an internal goal representation signal according to the observed power system states, therefore, to achieve more effective learning and modulating. Our control approach is validated on a wind power integrated benchmark system with two areas connected by HVDC transmission lines. Compared with the classical direct HDP and proportional integral control, our GrHDP approach demonstrates the improved transient stability under system faults. Moreover, experiments under different system operating conditions with signal transmission delays are also carried out to further verify the effectiveness and robustness of the proposed approach.

  1. Smart control application in the oscillations using FACTS (STATCOM and SVC

    Directory of Open Access Journals (Sweden)

    Alfonso James Alzate Gomez

    2017-07-01

    Full Text Available Context: Reducing the oscillations of the electrical power systems is an important task in order to maintain their stability. This paper presents a methodology for adjusting the parameters of a fuzzy oscillations controller with a Static Var Compensator (SVC and a Static Synchronous Compensator (STATCOM. Methodology: The methodology consists of tuning a fuzzy controller to dampen oscillations in an electrical power system, with different optimization techniques such as: Genetic Algorithms (GA, Particle Swarm Optimization (PSO, and Chaotic Optimization Algorithm (COA. Results: The voltage and speed oscillations of a system composed of a synchronous machine connected to an infinite bus bar (SMIB are obtained through simulations. There is data before and after connecting a SVC and a STATCOM, installed independently and in different operating conditions. The results obtained show that using a technique for adjusting parameters in the fuzzy controller is better than the adjustment of trial and error. Conclusion: With the obtained results, it is possible to verify the effectiveness of the fuzzy controller using Flexible AC Transmissions Systems (FACTS.

  2. Fault Ride through Capability Improvement of Wind Turbine Based DFIG Considering an Optimized Crowbar Along with STATCOM under Grid Fault Condition

    OpenAIRE

    Alireza Zohoori; Ahad Kazemi; Rouhollah Shafaie

    2013-01-01

    Grid disturbances, especially grid faults, have very unfavorable effect on the performance of wind turbine based Doubly Fed Induction Generator (DFIG). In this study active and reactive powers control of DFIG with STATCOM has been carried out to improve Fault Ride Through (FRT) capability of a wind turbine. In order to excel improvement of the DFIG behavior under grid fault disturbances, an optimized crowbar protection method is also considered together with STATCOM. The optimized protection ...

  3. Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate

    Science.gov (United States)

    Geng, Guoqing; Myers, Rupert J.; Li, Jiaqi; Maboudian, Roya; Carraro, Carlo; Shapiro, David A.; Monteiro, Paulo J. M.

    2017-03-01

    The incorporation of Al and increased curing temperature promotes the crystallization and cross-linking of calcium (alumino)silicate hydrate (C-(A-)S-H), which is the primary binding phase in most contemporary concrete materials. However, the influence of Al-induced structural changes on the mechanical properties at atomistic scale is not well understood. Herein, synchrotron radiation-based high-pressure X-ray diffraction is used to quantify the influence of dreierketten chain cross-linking on the anisotropic mechanical behavior of C-(A-)S-H. We show that the ab-planar stiffness is independent of dreierketten chain defects, e.g. vacancies in bridging tetrahedra sites and Al for Si substitution. The c-axis of non-cross-linked C-(A-)S-H is more deformable due to the softer interlayer opening but stiffens with decreased spacing and/or increased zeolitic water and Ca2+ of the interlayer. Dreierketten chain cross-links act as ‘columns’ to resist compression, thus increasing the bulk modulus of C-(A-)S-H. We provide the first experimental evidence on the influence of the Al-induced atomistic configurational change on the mechanical properties of C-(A-)S-H. Our work advances the fundamental knowledge of C-(A-)S-H on the lowest level of its hierarchical structure, and thus can impact the way that innovative C-(A-)S-H-based cementitious materials are developed using a ‘bottom-up’ approach.

  4. Using the Chain Rule as the Key Link in Deriving the General Rules for Differentiation

    Science.gov (United States)

    Sprows, David

    2011-01-01

    The standard approach to the general rules for differentiation is to first derive the power, product, and quotient rules and then derive the chain rule. In this short article we give an approach to these rules which uses the chain rule as the main tool in deriving the power, product, and quotient rules in a manner which is more student-friendly…

  5. Identification of a tetrasialylated monofucosylated tetraantennary N-linked carbohydrate chain in human platelet glycocalicin

    NARCIS (Netherlands)

    Vliegenthart, J.F.G.; Korrel, S.A.M.; Clemetson, K.J.; Halbeek, H. van; Kamerling, J.P.; Sixma, J.J.

    1988-01-01

    Glycocalicin (140 kDa), the main constituent of the glycoprotein Ib alpha-chain (150 kDa) of the human platelet membrane, contains 4 putative N-glycosylation sites. For the structural analysis of the N-glycosidic carbohydrate chains of glycocalicin, the glycoprotein has been subjected to the

  6. Primary structure of N-linked carbohydrate chains of a human chimeric plasminogen activator K2tu-PA expressed in Chinese hamster ovary cells

    NARCIS (Netherlands)

    Vliegenthart, J.F.G.; Bergwerff, A.A.; Oostrum, J. van; Asselbergs, F.A.M.; Bürgi, R.; Hokke, C.H.; Kamerling, J.P.

    1993-01-01

    A recombinant human plasminogen activator hybrid variant K2tu-PA, expressed in Chinese hamster ovary cells, is partially glycosylated at Asn12 (A chain, kringle-2 domain) and completely glycosylated at Asn247 (B chain, protease domain). After release of the N-linked carbohydrate chains by

  7. CORRECTION OF CHAIN-LINKING METHOD BY MEANS OF LLOYD-MOULTON-FISHER-TÖRNQVIST INDEX ON CROATIAN GDP DATA

    Directory of Open Access Journals (Sweden)

    Ante Rozga

    2013-02-01

    Full Text Available National statistical agencies of European Union use chain-linking method to achieve the best possible decomposition of GDP. The main advantage of this method is its simplicity, thus it can be applied in practice, which makes it particularly attractive in the situation when GDP has to be compiled on due time. By this method transformation-substitution effect – inherent to rational producers and consumers, has been implicitly built into GDP compilation, which is prior assumption of normative economic theory. On empirical (ex-post ground it gives more precise volume-price decomposition. In this paper, by means of constructing LMTF index and Fisher index derived from the previous one, it is suggested how to improve chain linking method, due to following reasons: a it is theoretically restrictive, b it gives only rough GDP decomposition into volume and price and, what seems to be its main disadvantage, c it gives additively inconsistent GDP.

  8. How to improve Kline and Rosenberg's chain-linked model of innovation: building blocks and diagram-based languages

    OpenAIRE

    Micaëlli, Jean-Pierre; Forest, Joelle; Coatanéa, Eric; Medyna, Galina

    2014-01-01

    article accessible aussi en ligne via le lien suivant : www.cairn.info/revue-journal-of-innovation-economics-2014-3-page-59.htm.; International audience; The "hierarchical and linear model of innovation" (HLMI) is often used to describe how innovations are produced. HLMI presents several shortcomings and one possible way of overcoming them is to consider innovations from a system perspective. In order to achieve this, this article uses Kline and Rosenberg's chain-linked model (CLM, 1985) as a...

  9. Robust state feedback controller design of STATCOM using chaotic optimization algorithm

    Directory of Open Access Journals (Sweden)

    Safari Amin

    2010-01-01

    Full Text Available In this paper, a new design technique for the design of robust state feedback controller for static synchronous compensator (STATCOM using Chaotic Optimization Algorithm (COA is presented. The design is formulated as an optimization problem which is solved by the COA. Since chaotic planning enjoys reliability, ergodicity and stochastic feature, the proposed technique presents chaos mapping using Lozi map chaotic sequences which increases its convergence rate. To ensure the robustness of the proposed damping controller, the design process takes into account a wide range of operating conditions and system configurations. The simulation results reveal that the proposed controller has an excellent capability in damping power system low frequency oscillations and enhances greatly the dynamic stability of the power systems. Moreover, the system performance analysis under different operating conditions shows that the phase based controller is superior compare to the magnitude based controller.

  10. Internal balance during low-voltage-ride-through of the modular multilevel converter statcom

    DEFF Research Database (Denmark)

    Tsolaridis, Georgios; Kontos, Epameinondas; Chaudhary, Sanjay K.

    2017-01-01

    Grid faults are common in power systems and can have a severe impact on the operation of the converters in the system. In this paper, the operation of a Modular Multilevel Converter (MMC)-based Static Synchronous Compensators (STATCOM) is investigated during grid faults. The study focuses...... on the challenging internal control of the converter to allow the independent control of the energy levels of each arm, with the goal to maintain internal balancing of the MMC during contingencies. Extensive experimental results highlight the need for a sophisticated internal control. Moreover, the experimental...... analysis verifies that, by using the proposed control structure, the MMC can effectively ride through a fault on the AC side without tripping, while injecting the necessary positive and negative sequence reactive current levels according to the most recent grid codes....

  11. High Order Voltage and Current Harmonic Mitigation Using the Modular Multilevel Converter STATCOM

    DEFF Research Database (Denmark)

    Kontos, Epameinondas; Tsolaridis, Georgios; Teodorescu, Remus

    2017-01-01

    Due to the increase of power electronic-based loads, the maintenance of high power quality poses a challenge in modern power systems. To limit the total harmonic distortion in the line voltage and currents at the point of the common coupling (PCC), active power filters are commonly employed....... This paper investigates the use of the multilevel modular converter (MMC) for harmonics mitigation due to its high bandwidth compared with conventional converters. A selective harmonics detection method and a harmonics controller are implemented, while the output current controller of the MMC is tuned...... to selectively inject the necessary harmonic currents. Unlike previous studies, focus is laid on the experimental verification of the active filtering capability of the MMC. For this reason an MMC-based double-star STATCOM is developed and tested for two representative case studies, i.e., for grid currents...

  12. Design and Tuning of Wind Power Plant Voltage Controller with Embedded Application of Wind Turbines and STATCOMs

    DEFF Research Database (Denmark)

    Petersen, Lennart; Kryezi, Fitim; Iov, Florin

    2017-01-01

    This study addresses a detailed design and tuning of a wind power plant voltage control with reactive power contribution of wind turbines and static synchronous compensators (STATCOMs). First, small-signal models of a single wind turbine and STATCOM are derived by using the state-space approach....... A complete phasor model of the entire wind power plant is constructed, being appropriate for voltage control assessment. An exemplary wind power plant located in the United Kingdom and the corresponding grid code requirements are used as a base case. The final design and tuning process of the voltage...... controller results in a guidance, proposed for this particular control architecture. It provides qualitative outcomes regarding the parametrisation of each individual control loop and how to adjust the voltage controller depending on different grid stiffnesses of the wind power plant connection...

  13. The cold chain and the weakest link; De koudeketen en de zwakste schakel

    Energy Technology Data Exchange (ETDEWEB)

    Moerman, P.C.

    2005-11-01

    The production of food products requires a proper control system to guarantee the quality of the products at the end of the distribution chain. A HACCP (Hazard Analysis of Critical Control Points) system provides a scheme for proper handling in a cold chain. Two examples are described: a cold chain for chilled meat and a cold chain for frozen products. For each step in the chains the critical control points are described. The indicated parameters had to be monitored and controlled to achieve good end products. [Dutch] Om bederfelijke producten veilig bij de gebruiker te brengen is een keten van handelingen nodig: de koudeketen. De parameters van de toegepas-te processtappen dienen beheerst te worden. Hiervoor kan men het HACCP ((Hazard Analysis of Critical Control Points) systeem gebruiken. Twee voorbeelden worden gegeven: een koelketen voor vers vlees en een vriesketen. Voor beide ketens wordt voor een aantal processtappen aangegeven welke grootheden kritisch zijn en dus beheerst moeten worden om tot een goed resultaat te komen.

  14. A STATCOM with Supercapacitors for Low-Voltage Ride-Through in Fixed-Speed Wind Turbines

    Directory of Open Access Journals (Sweden)

    Andrés Felipe Obando-Montaño

    2014-09-01

    Full Text Available Fixed-speed wind generator (FSWG technology has an important presence in countries where wind energy started to be developed more than a decade ago. This type of technology cannot be directly adapted to the grid codes, for example those requirements related to the immunity level under voltage dips. That behavior is typically referred as low-voltage ride through (LVRT, and it usually implies certain reactive and active power injection requirements, both during a voltage dip and during the voltage recovery. In this context, a review is presented of the LVRT exigencies present in some of the countries with the most advanced grid codes (Denmark, Germany, Spain and the United Kingdom. In this paper, the capabilities of STATCOM-based devices for fulfilling the LVRT requirements in FSWGs are analyzed. For this purpose, two technologies are considered: a STATCOM with a supercapacitor, which improves its energy storage features; and a STATCOM with a supercapacitor and a DC-DC converter, to achieve higher discharge levels.

  15. Crystal structure of a samarium(III nitrate chain cross-linked by a bis-carbamoylmethylphosphine oxide ligand

    Directory of Open Access Journals (Sweden)

    Julie A. Stoscup

    2014-10-01

    Full Text Available In the title compound poly[aquabis(μ-nitrato-κ4O,O′:O,O′′tetrakis(nitrato-κ2O,O′{μ4-tetraethyl [(ethane-1,2-diylbis(azanediylbis(2-oxoethane-2,1-diyl]diphosphonate-κ2O,O′}disamarium(III], [Sm2(NO36(C14H30N2O8P2(H2O]n, a 12-coordinate SmIII and a nine-coordinate SmIII cation are alternately linked via shared bis-bidentate nitrate anions into a corrugated chain extending parallel to the a axis. The nine-coordinate SmIII atom of this chain is also chelated by a bidentate, yet flexible, carbamoylmethylphoshine oxide (CMPO ligand and bears one water molecule. This water molecule is hydrogen bonded to nitrate groups bonded to the 12-coordinate SmIII cation. The CMPO ligand, which lies about an inversion center, links neighboring chains along the c axis, forming sheets parallel to the ac plane. Hydrogen bonds between the amide NH group and metal-bound nitrate anions are also present in these sheets. The sheets are packed along the b axis through only van der Waals interactions.

  16. Opening and linking up: Firms, global value chains and productivity in Latin America

    NARCIS (Netherlands)

    Montalbano, Pierluigi; Nenci, Silvia; Pietrobelli, Carlo

    2017-01-01

    This work explores the relationship between exports, Global Value Chains' (GVCs) participation and position, and firms' productivity. To this aim, we combine the most recent World Bank Enterprise Survey in Latin American and Caribbean (LAC) countries with the OECD-WTO trade in value added data. To

  17. Risks and governance modes in offshoring decisions : Linking supply chain management and international business perspectives

    NARCIS (Netherlands)

    Patrucco, A.S.; Scalera, V.G.; Luzzini, D.

    2016-01-01

    Governing offshoring has become a major challenge for firms that run operations outside the home country. International business (IB) and supply chain management (SCM) literature offer different insights on the topic, focusing especially on possible governance modes and the drivers of this choice,

  18. HTLV-1 Tax Induces Formation of the Active Macromolecular IKK Complex by Generating Lys63- and Met1-Linked Hybrid Polyubiquitin Chains.

    Science.gov (United States)

    Shibata, Yuri; Tokunaga, Fuminori; Goto, Eiji; Komatsu, Ginga; Gohda, Jin; Saeki, Yasushi; Tanaka, Keiji; Takahashi, Hirotaka; Sawasaki, Tatsuya; Inoue, Satoshi; Oshiumi, Hiroyuki; Seya, Tsukasa; Nakano, Hiroyasu; Tanaka, Yuetsu; Iwai, Kazuhiro; Inoue, Jun-Ichiro

    2017-01-01

    The Tax protein of human T-cell leukemia virus type 1 (HTLV-1) is crucial for the development of adult T-cell leukemia (ATL), a highly malignant CD4+ T cell neoplasm. Among the multiple aberrant Tax-induced effects on cellular processes, persistent activation of transcription factor NF-κB, which is activated only transiently upon physiological stimulation, is essential for leukemogenesis. We and others have shown that Tax induces activation of the IκB kinase (IKK) complex, which is a critical step in NF-κB activation, by generating Lys63-linked polyubiquitin chains. However, the molecular mechanism underlying Tax-induced IKK activation is controversial and not fully understood. Here, we demonstrate that Tax recruits linear (Met1-linked) ubiquitin chain assembly complex (LUBAC) to the IKK complex and that Tax fails to induce IKK activation in cells that lack LUBAC activity. Mass spectrometric analyses revealed that both Lys63-linked and Met1-linked polyubiquitin chains are associated with the IKK complex. Furthermore, treatment of the IKK-associated polyubiquitin chains with Met1-linked-chain-specific deubiquitinase (OTULIN) resulted in the reduction of high molecular weight polyubiquitin chains and the generation of short Lys63-linked ubiquitin chains, indicating that Tax can induce the generation of Lys63- and Met1-linked hybrid polyubiquitin chains. We also demonstrate that Tax induces formation of the active macromolecular IKK complex and that the blocking of Tax-induced polyubiquitin chain synthesis inhibited formation of the macromolecular complex. Taken together, these results lead us to propose a novel model in which the hybrid-chain-dependent oligomerization of the IKK complex triggered by Tax leads to trans-autophosphorylation-mediated IKK activation.

  19. Structure of three acidic O-linked carbohydrate chains of porcine zona pellucida glycoproteins

    NARCIS (Netherlands)

    Vliegenthart, J.F.G.; Hokke, C.H.; Damm, J.B.L.; Kamerling, J.P.

    1993-01-01

    Structural analysis by ID and 2D 1H NMR spectroscopy of three acidic O-linked oligosaccharide alditols, released from porcine zona pellucida glycoproteins by alkaline borohydride treatment, afforded the following structures: Gal beta l-4(6SO4-)GlcNAc beta l-3Gal beta l-4GlcNAc beta 1-3Gal beta

  20. Meaning in Life: One Link in the Chain from Religiousness to Well-Being

    Science.gov (United States)

    Steger, Michael F.; Frazier, Patricia

    2005-01-01

    Meaning in life has been identified as a potential mediator of the link between religiousness and psychological health. The authors tested this hypothesis in 2 studies, using multiple methods and measures of religiousness and well-being. In the studies, meaning in life mediated the relation between religiousness and life satisfaction (Study 1A),…

  1. Ether- versus ester-linked phospholipid bilayers containing either linear or branched apolar chains.

    Science.gov (United States)

    Balleza, Daniel; Garcia-Arribas, Aritz B; Sot, Jesús; Ruiz-Mirazo, Kepa; Goñi, Félix M

    2014-09-16

    We studied the properties of bilayers formed by ether-and ester-containing phospholipids, whose hydrocarbon chains can be either linear or branched, using sn-1,2 dipalmitoyl, dihexadecyl, diphytanoyl, and diphytanyl phosphatidylcholines (DPPC, DHPC, DPhoPC, and DPhPC, respectively) either pure or in binary mixtures. Differential scanning calorimetry and confocal fluorescence microscopy of giant unilamellar vesicles concurred in showing that equimolar mixtures of linear and branched lipids gave rise to gel/fluid phase coexistence at room temperature. Mixtures containing DHPC evolved in time (0.5 h) from initial reticulated domains to extended solid ones when an equilibrium was achieved. The nanomechanical properties of supported planar bilayers formed by each of the four lipids studied by atomic force microscopy revealed average breakdown forces Fb decreasing in the order DHPC ≥ DPPC > DPhoPC > DPhPC. Moreover, except for DPPC, two different Fb values were found for each lipid. Atomic force microscopy imaging of DHPC was peculiar in showing two coexisting phases of different heights, probably corresponding to an interdigitated gel phase that gradually transformed, over a period of 0.5 h, into a regular tilted gel phase. Permeability to nonelectrolytes showed that linear-chain phospholipids allowed a higher rate of solute + water diffusion than branched-chain phospholipids, yet the former supported a smaller extent of swelling of the corresponding vesicles. Ether or ester bonds appeared to have only a minor effect on permeability. Copyright © 2014 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  2. New Link in Bioinformatics Services Value Chain: Position, Organization and Business Model

    Directory of Open Access Journals (Sweden)

    Mladen Čudanov

    2012-11-01

    Full Text Available This paper presents development in the bioinformatics services industry value chain, based on cloud computing paradigm. As genome sequencing costs per Megabase exponentially drop, industry needs to adopt. Paper has two parts: theoretical analysis and practical example of Seven Bridges Genomics Company. We are focused on explaining organizational, business and financial aspects of new business model in bioinformatics services, rather than technical side of the problem. In the light of that we present twofold business model fit for core bioinformatics research and Information and Communication Technologie (ICT support in the new environment, with higher level of capital utilization and better resistance to business risks.

  3. Persistent Identifiers for Field Deployments: A Missing Link in the Provenance Chain

    Science.gov (United States)

    Arko, R. A.; Ji, P.; Fils, D.; Shepherd, A.; Chandler, C. L.; Lehnert, K.

    2016-12-01

    Research in the geosciences is characterized by a wide range of complex and costly field deployments including oceanographic cruises, submersible dives, drilling expeditions, seismic networks, geodetic campaigns, moored arrays, aircraft flights, and satellite missions. Each deployment typically produces a mix of sensor and sample data, spanning a period from hours to decades, that ultimately yields a long tail of post-field products and publications. Publishing persistent, citable identifiers for field deployments will facilitate 1) preservation and reuse of the original field data, 2) reproducibility of the resulting publications, and 3) recognition for both the facilities that operate the platforms and the investigators who secure funding for the experiments. In the ocean domain, sharing unique identifiers for field deployments is a familiar practice. For example, the Biological and Chemical Oceanography Data Management Office (BCO-DMO) routinely links datasets to cruise identifiers published by the Rolling Deck to Repository (R2R) program. In recent years, facilities have started to publish formal/persistent identifiers, typically Digital Object Identifiers (DOIs), for field deployments including seismic networks, oceanographic cruises, and moored arrays. For example, the EarthChem Library (ECL) publishes a DOI for each dataset which, if it derived from an oceanographic research cruise on a US vessel, is linked to a DOI for the cruise published by R2R. Work is underway to create similar links for the IODP JOIDES Resolution Science Operator (JRSO) and the Continental Scientific Drilling Coordination Office (CSDCO). We present results and lessons learned including a draft schema for publishing field deployments as DataCite DOI records; current practice for linking these DOIs with related identifiers such as Open Researcher and Contributor IDs (ORCIDs), Open Funder Registry (OFR) codes, and International Geo Sample Numbers (IGSNs); and consideration of other

  4. Fluorescence spectroscopic study of the aggregation behavior of non-cross-linked and cross-linked poly(alkylmethyldiallylammonium bromides) having decyl, octyl, and hexyl side chains in aqueous solution

    NARCIS (Netherlands)

    Wang, G.J; Engberts, J.B.F.N.

    1996-01-01

    The conformational state of a series of non-cross-linked and cross-linked poly(alkylmethyldiallylammonium bromides) bearing decyl, octyl, and hexyl side chains ((CL)-CopolC1-10, (CL)-CopolC1-8, and (CL)-CopolC1-6, respectively) in aqueous solutions were investigated by fluorescence spectroscopy

  5. Making climate science accessible in Toledo: The linked boundary chain approach

    Directory of Open Access Journals (Sweden)

    Scott E. Kalafatis

    2015-01-01

    Full Text Available For many cities throughout the world, climate change not only presents challenges in the form of new risks and expenses, but also opportunities to connect work around climate change to other development and environmental initiatives. This study presents the City of Toledo in the heart of America’s Rust Belt as a case study of the policy process that gives rise to proactive action on climate change. Using thick description, we trace Toledo’s adaptation policy process through the lens of Kingdon’s “multiple streams” model to identify factors that have shaped the emergence of climate adaptation work around water management in Toledo. Through doing so, we give particular attention to the knowledge resources that those in the City have relied on, especially its boundary chain connection with two supporting boundary organizations: GLAA-C and GLISA. Policy entrepreneurs pushing for climate adaptation around water policy in Toledo emerged around two separate pieces of the policy process. The first entrepreneur was involved with raising general awareness about sustainability and climate change in the City’s problem stream, and the other was specifically involved with integrating climate change information into a particular aspect of the City’s policy stream, water management. While these relationships were important for mainstreaming climate change adaptation into efforts to address existing challenges, they were also representative of the City’s ability to cultivate broader partnerships around climate adaptation. Toledo’s polycentric climate change network ultimately helped the City sustain its adaptation work as it weathered its own period of internal transition.

  6. Impact of Switching Harmonics on Capacitor Cells Balancing in Phase-Shifted PWM-Based Cascaded H-Bridge STATCOM

    DEFF Research Database (Denmark)

    Behrouzian, Ehsan; Bongiorno, Massimo; Teodorescu, Remus

    2017-01-01

    The purpose of this paper is to investigate the impact of switching harmonics on the instantaneous power distribution in the cells of a cascaded H-bridge-based STATCOM when using phase-shifted pulse width modulation. The case of high- and low-switching frequency for the converter cells...... control loops. It is also shown that the selected frequency modulation ratio affects the active power distribution among the cells. In particular, the selection of a noninteger frequency modulation ratio helps in providing a more uniform power distribution among cells of the same phase leg, thus...

  7. Morphological and molecular characterization of a new succulenticolous Physarum (Myxomycetes, Amoebozoa) with unique polygonal spores linked in chains.

    Science.gov (United States)

    García-Martín, Joaquina María; Mosquera, Juan; Lado, Carlos

    2017-12-22

    A new plasmodiocarpic and sporocarpic species of myxomycete in the genus Physarum is described and illustrated. This new species appeared on decayed leaves and remains of succulent plants (Agave, Opuntia, Yucca) growing in arid zones. It differs from all other species in the genus in having polyhedral spores linked in chains like a string of beads, a unique feature within all known myxomycetes. Apart from detailed morphological data, partial sequences of both the small-subunit ribosomal RNA and elongation factor 1-alpha genes, generated from four isolates collected in two distant regions, i.e., Mexico and Canary Islands, are also provided in this study. Combined evidence supports the identity of the specimens under study as a new species. Copyright © 2017 Elsevier GmbH. All rights reserved.

  8. A Novel Grey Prediction Model Combining Markov Chain with Functional-Link Net and Its Application to Foreign Tourist Forecasting

    Directory of Open Access Journals (Sweden)

    Yi-Chung Hu

    2017-10-01

    Full Text Available Grey prediction models for time series have been widely applied to demand forecasting because only limited data are required for them to build a time series model without any statistical assumptions. Previous studies have demonstrated that the combination of grey prediction with neural networks helps grey prediction perform better. Some methods have been presented to improve the prediction accuracy of the popular GM(1,1 model by using the Markov chain to estimate the residual needed to modify a predicted value. Compared to the previous Grey-Markov models, this study contributes to apply the functional-link net to estimate the degree to which a predicted value obtained from the GM(1,1 model can be adjusted. Furthermore, the troublesome number of states and their bounds that are not easily specified in Markov chain have been determined by a genetic algorithm. To verify prediction performance, the proposed grey prediction model was applied to an important grey system problem—foreign tourist forecasting. Experimental results show that the proposed model provides satisfactory results compared to the other Grey-Markov models considered.

  9. The role of ELOVL1 in very long-chain fatty acid homeostasis and X-linked adrenoleukodystrophy

    Science.gov (United States)

    Ofman, Rob; Dijkstra, Inge M E; van Roermund, Carlo W T; Burger, Nena; Turkenburg, Marjolein; van Cruchten, Arno; van Engen, Catherine E; Wanders, Ronald J A; Kemp, Stephan

    2010-01-01

    X-linked adrenoleukodystrophy (X-ALD) is caused by mutations in the ABCD1 gene encoding the peroxisomal ABC transporter adrenoleukodystrophy protein (ALDP). X-ALD is characterized by the accumulation of very long-chain fatty acids (VLCFA; ≥C24) in plasma and tissues. In this manuscript we provide insight into the pathway underlying the elevated levels of C26:0 in X-ALD. ALDP transports VLCFacyl-CoA across the peroxisomal membrane. A deficiency in ALDP impairs peroxisomal β-oxidation of VLCFA but also raises cytosolic levels of VLCFacyl-CoA which are substrate for further elongation. We identify ELOVL1 (elongation of very-long-chain-fatty acids) as the single elongase catalysing the synthesis of both saturated VLCFA (C26:0) and mono-unsaturated VLCFA (C26:1). ELOVL1 expression is not increased in X-ALD fibroblasts suggesting that increased levels of C26:0 result from increased substrate availability due to the primary deficiency in ALDP. Importantly, ELOVL1 knockdown reduces elongation of C22:0 to C26:0 and lowers C26:0 levels in X-ALD fibroblasts. Given the likely pathogenic effects of high C26:0 levels, our findings highlight the potential of modulating ELOVL1 activity in the treatment of X-ALD. PMID:20166112

  10. Capacitor voltage balance performance comparison of MMC-STATCOM using NLC and PS-PWM strategies during negative sequence current injection

    DEFF Research Database (Denmark)

    Pereira, Heverton A.; F. Cupertino, Allan; S. Xavier, Lucus

    2016-01-01

    modulation, during positive and negative sequence current injection. Results of a 15 MVA MMC STATCOM show that the nearest level control strategy has lower average switching frequency compared to the phase-shifted pulse width modulation strategy, considering comparable submodule capacitance voltage ripple....

  11. Two mutational hotspots in the interleukin-2 receptor {gamma} chain gene causing human X-linked severe combined immunodeficiency

    Energy Technology Data Exchange (ETDEWEB)

    Pepper, A.E.; Puck, J.M. [National Institutes of Health, Bethesda, MD (United States); Buckley, R.H. [and others

    1995-09-01

    Human severe combined immunodeficiency (SCID), a syndrome of profoundly impaired cellular and humoral immunity, is most commonly caused by mutations in the X-linked gene for interleukin-2 (IL-2) receptor {gamma} chain (IL2RG). For mutational analysis of IL2RG in males with SCID, SSCP screening was followed by DNA sequencing. Of 40 IL2RG mutations found in unrelated SCID patients, 6 were point mutations at the CpG dinucleotide at cDNA 690-691, encoding amino acid R226. This residue lies in the extracellular domain of the protein in a region not previously recognized to be significantly conserved in the cytokine receptor gene family, 11 amino acids upstream from the highly conserved WSXWS motif. Three additional instances of mutation at another CpG dinucleotide at cDNA 879 produced a premature termination signal in the intracellular domain of IL2RG, resulting in loss of the SH2-homologous intracellular domain known to be essential for signaling from the IL-2 receptor complex. Mutations at these two hotspots constitute >20% of the X-linked SCID mutations found by our group and a similar proportion of all reported IL2RG mutations. 41 refs., 5 figs., 1 tab.

  12. [Autism spectrum disorders and bisphenol A: Is serotonin the lacking link in the chain?

    Science.gov (United States)

    Sarrouilhe, D; Dejean, C

    2017-08-01

    the other hand, hyperserotonemia was reported in approximately one-third of autistic patients and also in relatives. Moreover, neuroimaging studies revealed two fundamentally different types of serotonin synthesis abnormality in children with autism compared to age-matched nonautistic children, a difference in whole-brain capacity and focal abnormalities. Finally, decreased serotonin transporter and serotonin receptor binding have been reported in both children and adults with autism. So, the link between BPA and autism could be a defect of the normal in utero or perinatal serotonergic system development. In France, BPA was banned in baby bottles in 2010 and in any food or beverage packaging since January 2015. Therefore, there is an urgent need to find safe alternatives in the use of BPA in the manufacture of industrial products. Copyright © 2016 L'Encéphale, Paris. Published by Elsevier Masson SAS. All rights reserved.

  13. Real time hardware implementation of power converters for grid integration of distributed generation and STATCOM systems

    Science.gov (United States)

    Jaithwa, Ishan

    Deployment of smart grid technologies is accelerating. Smart grid enables bidirectional flows of energy and energy-related communications. The future electricity grid will look very different from today's power system. Large variable renewable energy sources will provide a greater portion of electricity, small DERs and energy storage systems will become more common, and utilities will operate many different kinds of energy efficiency. All of these changes will add complexity to the grid and require operators to be able to respond to fast dynamic changes to maintain system stability and security. This thesis investigates advanced control technology for grid integration of renewable energy sources and STATCOM systems by verifying them on real time hardware experiments using two different systems: d SPACE and OPAL RT. Three controls: conventional, direct vector control and the intelligent Neural network control were first simulated using Matlab to check the stability and safety of the system and were then implemented on real time hardware using the d SPACE and OPAL RT systems. The thesis then shows how dynamic-programming (DP) methods employed to train the neural networks are better than any other controllers where, an optimal control strategy is developed to ensure effective power delivery and to improve system stability. Through real time hardware implementation it is proved that the neural vector control approach produces the fastest response time, low overshoot, and, the best performance compared to the conventional standard vector control method and DCC vector control technique. Finally the entrepreneurial approach taken to drive the technologies from the lab to market via ORANGE ELECTRIC is discussed in brief.

  14. A molecular dynamics study on the buckling behavior of cross-linked functionalized carbon nanotubes under physical adsorption of polymer chains

    Science.gov (United States)

    Ajori, S.; Ansari, R.; Haghighi, S.

    2018-01-01

    The buckling behavior of cross-linked functionalized carbon nanotubes (CNTs) with polyethylene (PE) chains under physical adsorption of polymers (cfCNTs/polymer) is studied by classical molecular dynamics (MD) simulations, and the results are compared with those for the pure CNTs under the physical adsorption of polymers. Considering non-covalent functionalization, the effect of type of functional group, i.e. aramid and PE chains, on the interactions between polymers and cfCNTs is investigated. Based on the results, the gyration radius of cfCNTs/polymer increases by raising the weight percentage of non-covalent polymer chains. Also, the simulation results for most cases demonstrate that the gyration radius of cfCNTs/polymer is larger than that of pure CNTs/polymer for the similar weight percentage of non-covalent polymer chains. Moreover, the critical buckling force and the critical buckling strain of the cfCNTs/polymer are lower than those of pure CNT/polymer for the similar weight percentage of non-covalent polymer chains, although some exceptions can be observed. Besides, by raising the weight percentage of non-covalent polymer chains, the critical buckling force cfCNTs/polymer increases for a specific weight percentage of cross-linked PE chains.

  15. Bezafibrate lowers very long-chain fatty acids in X-linked adrenoleukodystrophy fibroblasts by inhibiting fatty acid elongation.

    Science.gov (United States)

    Engelen, Marc; Schackmann, Martin J A; Ofman, Rob; Sanders, Robert-Jan; Dijkstra, Inge M E; Houten, Sander M; Fourcade, Stéphane; Pujol, Aurora; Poll-The, Bwee Tien; Wanders, Ronald J A; Kemp, Stephan

    2012-11-01

    X-linked adrenoleukodystrophy (X-ALD) is caused by mutations in the ABCD1 gene encoding ALDP, an ATP-binding-cassette (ABC) transporter located in the peroxisomal membrane. ALDP deficiency results in impaired peroxisomal β-oxidation and the subsequent accumulation of very long-chain fatty acids (VLCFA; > C22:0) in plasma and tissues. VLCFA are primarily derived from endogenous synthesis by ELOVL1. Therefore inhibiting this enzyme might constitute a feasible therapeutic approach. In this paper we demonstrate that bezafibrate, a PPAR pan agonist used for the treatment of patients with hyperlipidaemia reduces VLCFA levels in X-ALD fibroblasts. Surprisingly, the VLCFA-lowering effect was independent of PPAR activation and not caused by the increase in either mitochondrial or peroxisomal fatty acid β-oxidation capacity. In fact, our results show that bezafibrate reduces VLCFA synthesis by decreasing the synthesis of C26:0 through a direct inhibition of fatty acid elongation activity. Taken together, our data indicate bezafibrate as a potential pharmacotherapeutic treatment for X-ALD. A clinical trial is currently ongoing to evaluate the effect in patients with X-ALD.

  16. Development of a novel polymerase chain reaction-enzyme-linked immunosorbent assay for the diagnosis of Trichophyton rubrum onychomycosis.

    Science.gov (United States)

    Pankewitz, F; Nenoff, P; Uhrlaß, S; Bezold, G; Winter, I; Gräser, Y

    2013-06-01

    The prevalence of onychomycosis has increased steadily in the past decade. An accurate diagnosis at the outset is important for successful and cost-effective treatment of patients. However, current diagnostic tests for onychomycosis are not rapid, sensitive or specific. To develop a microsatellite-based polymerase chain reaction (PCR)-enzyme-linked immunosorbent assay (MS-ELISA) for the detection of Trichophyton rubrum, which is the most common aetiological agent of onychomycosis. An archival set of 434 nail and skin specimens from 217 patients was included as the test sample in this study. We also compared MS-ELISA with an earlier published topoisomerase PCR-ELISA (TI-ELISA) using template DNA extracted by another method. The MS-ELISA detected the highest number of positive samples (69%) followed by direct microscopy (56%), TI-ELISA (44%) and fungal culture (30%). When an identical DNA extraction method was applied to 120 specimens, the MS-ELISA proved to be twice as sensitive as the TI-ELISA. We have optimized a target gene and DNA extraction method for rapid detection of T. rubrum onychomycosis. © 2013 The Authors. BJD © 2013 British Association of Dermatologists.

  17. X-linked adrenoleukodystrophy: very long-chain fatty acid metabolism is severely impaired in monocytes but not in lymphocytes

    Science.gov (United States)

    Weber, Franziska D.; Wiesinger, Christoph; Forss-Petter, Sonja; Regelsberger, Günther; Einwich, Angelika; Weber, Willi H.A.; Köhler, Wolfgang; Stockinger, Hannes; Berger, Johannes

    2014-01-01

    X-linked adrenoleukodystrophy (X-ALD) is a fatal neurodegenerative disease caused by mutations in the ABCD1 gene, encoding a member of the peroxisomal ABC transporter family. The ABCD1 protein transports CoA-activated very long-chain fatty acids (VLCFAs) into peroxisomes for degradation via β-oxidation. In the severest form, X-ALD patients suffer from inflammatory demyelination of the brain. As the extent of the metabolic defect in the main immune cells is unknown, we explored their phenotypes concerning mRNA expression pattern of the three peroxisomal ABC transporters, VLCFA accumulation and peroxisomal β-oxidation. In controls, ABCD1 expression was high in monocytes, intermediate in B cells and low in T cells; ABCD2 expression was extremely low in monocytes, intermediate in B cells and highest in T cells; ABCD3 mRNA was equally distributed. In X-ALD patients, the expression patterns remained unaltered; accordingly, monocytes, which lack compensatory VLCFA transport by ABCD2, displayed the severest biochemical phenotype with a 6-fold accumulation of C26:0 and a striking 70% reduction in peroxisomal β-oxidation activity. In contrast, VLCFA metabolism was close to control values in B cells and T cells, supporting the hypothesis that sufficient ABCD2 is present to compensate for ABCD1 deficiency. Thus, the vulnerability of the main immune cell types is highly variable in X-ALD. Based on these results, we propose that in X-ALD the halt of inflammation after allogeneic hematopoietic stem cell transplantation relies particularly on the replacement of the monocyte lineage. Additionally, these findings support the concept that ABCD2 is a target for pharmacological induction as an alternative therapeutic strategy. PMID:24363066

  18. X-linked adrenoleukodystrophy: very long-chain fatty acid metabolism is severely impaired in monocytes but not in lymphocytes.

    Science.gov (United States)

    Weber, Franziska D; Wiesinger, Christoph; Forss-Petter, Sonja; Regelsberger, Günther; Einwich, Angelika; Weber, Willi H A; Köhler, Wolfgang; Stockinger, Hannes; Berger, Johannes

    2014-05-15

    X-linked adrenoleukodystrophy (X-ALD) is a fatal neurodegenerative disease caused by mutations in the ABCD1 gene, encoding a member of the peroxisomal ABC transporter family. The ABCD1 protein transports CoA-activated very long-chain fatty acids (VLCFAs) into peroxisomes for degradation via β-oxidation. In the severest form, X-ALD patients suffer from inflammatory demyelination of the brain. As the extent of the metabolic defect in the main immune cells is unknown, we explored their phenotypes concerning mRNA expression pattern of the three peroxisomal ABC transporters, VLCFA accumulation and peroxisomal β-oxidation. In controls, ABCD1 expression was high in monocytes, intermediate in B cells and low in T cells; ABCD2 expression was extremely low in monocytes, intermediate in B cells and highest in T cells; ABCD3 mRNA was equally distributed. In X-ALD patients, the expression patterns remained unaltered; accordingly, monocytes, which lack compensatory VLCFA transport by ABCD2, displayed the severest biochemical phenotype with a 6-fold accumulation of C26:0 and a striking 70% reduction in peroxisomal β-oxidation activity. In contrast, VLCFA metabolism was close to control values in B cells and T cells, supporting the hypothesis that sufficient ABCD2 is present to compensate for ABCD1 deficiency. Thus, the vulnerability of the main immune cell types is highly variable in X-ALD. Based on these results, we propose that in X-ALD the halt of inflammation after allogeneic hematopoietic stem cell transplantation relies particularly on the replacement of the monocyte lineage. Additionally, these findings support the concept that ABCD2 is a target for pharmacological induction as an alternative therapeutic strategy.

  19. Comparison of Field Measurements and EMT Simulation Results on a Multi-Level STATCOM for Grid Integration of London Array Wind Farm

    DEFF Research Database (Denmark)

    Glasdam, Jakob Bærholm; Kocewiak, Lukasz; Hjerrild, Jesper

    2014-01-01

    Simulation results are widely used in the design of electrical systems such as offshore wind power plants (OWPPs) and for determination of grid compliance. Measurements constitute an important part in the evaluation process of the OWPP, including passive and active components such as the static...... compensator (STATCOM). Quality measurement data allow the system designer to obtain real-life knowledge on the operating characteristics of the electrical component(s) for various operating scenarios of both the OWPP and the external grid. Furthermore, measurement data constitute an indispensable part...... of the evaluation of the simulation models of the OWPP components. The purpose of this paper is to develop and validate an electromagnetic transient (EMT) generic model of the modular multi-level cascaded converter (MMCC) STATCOM based on comparison with field measurements. For this purpose, measurement data have...

  20. Emergy and end-point impact assessment of agricultural and food production in the United States:a supply chain-linked ecologically-based life cycle assessment

    OpenAIRE

    Park, Yong Shin; Eğilmez, Gökhan; Küçükvar, Murat

    2016-01-01

    The concept of tracing the ecologically-based life cycle impacts of agricultural and food industries (AFIs)has become a topic of interest worldwide due to their criticalassociation with the climate change,water and land footprint, and food security. In this study, an indepth analysis of ecology resourceconsumption, atmospheric emissions, land and water footprints of 54 agricultural and food industriesinthe U.S. were examined extensively. Initially, the supply-chain linked ecological life cycl...

  1. Monitoring of very long-chain fatty acids levels in X-linked adrenoleukodystrophy, treated with haematopoietic stem cell transplantation and Lorenzo's Oil.

    Science.gov (United States)

    Stradomska, Teresa J; Drabko, Katarzyna; Moszczyńska, Elżbieta; Tylki-Szymańska, Anna

    2014-01-01

    X-linked adrenoleukodystrophy is a rare, neurodegenerative peroxisomal disorder connected with mutation in the ABCD1 gene, causing impairment of the peroxisomal β-oxidation process and in consequence, accumulation of very long-chain fatty acids (VLCFA) in blood and tissues. In this study we present serum very long-chain fatty acids levels during clinical course in an X-linked adrenoleukodystrophy patient after haematopoietic stem cell transplantation (HSCT) and on Lorenzo's Oil in a 11 years' period. The patient was diagnosed at the age of 8 months by family screening. The administration of LO was started at 2 years of age. HSCT from a family donor was performed twice. VLCFA serum levels were detected by the GC method. Chimaerism subsequent to HSCT was also analyzed. Increasing very long-chain fatty acids levels correlate with a decreasing chimaerism level after haematopoietic stem cell transplantation. The sequential monitoring of very long-chain fatty acids serum levels is important and useful for assessment of engraftment, graft failure or rejection.

  2. The effect of some disiloxane chain extenders on the thermal and mechanical properties of cross-linked poly(siloxane-urethanes

    Directory of Open Access Journals (Sweden)

    E. Pusztai

    2013-05-01

    Full Text Available Poly(siloxane-urethane (PSiU networks based on a bis(hydroxyorgano disiloxane chain extender, a trifunctional polyether polyol as a cross-linker, methylene-diphenyl diisocyanate and α,β-hydroxyethoxyethyl polydimethylsiloxane were synthesized in butyl acetate solution. The effect of the chain extenders and the cross-link density was investigated by using thermogravimetric analysis (TGA, dynamic mechanical thermal analysis (DMTA, swelling, hardness and tensile strength measurements. Isotherm thermogravimetric analyses were carried out for selected polymer compositions at 120 and 170°C and also the changes in tensile strength were followed. The different chain extenders have a strong effect on the hard segment structure, thus on the thermal and mechanical behaviour. The phase separation of the soft and hard segments was indicated by the two or three well distinguished tanδ peaks, the maxima of which range within wide intervals depending on the polymer composition. The polymers of high cross-link density showed a very good thermal stability, high tensile strength (up to 68.7 MPa and hardness (80–95 Shore A even of high 13–36% dimethyl siloxane content. Changing the siloxane soft segment ratio and the cross-link density the physical properties can be adjusted.

  3. New surface-modified zinc oxide nanoparticles with aminotriethylene oxide chains linked by 1,2,3-triazole ring: Preparation, and visible light-emitting and noncytotoxic properties

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Moriyuki, E-mail: msato@riko.shimane-u.ac.jp [Faculty of Science and Engineering, Shimane University, 1060 Nishikawatsu, Matsue, Shimane 690 8504 (Japan); Shimatani, Kanako; Iwasaki, Yuko; Morito, Shigekazu; Tanaka, Hidekazu; Fujita, Yasuhisa [Faculty of Science and Engineering, Shimane University, 1060 Nishikawatsu, Matsue, Shimane 690 8504 (Japan); Nakamura, Morihiko [Department of Cooperative Medical Research, Collaboration Center, Shimane University, 891 Enya, Izumo, Shimane 693 8501 (Japan)

    2011-11-01

    Novel surface-modified, visible light-emitting and noncytotoxic ZnO nanoparticles (NPs) (ZPAZ) having aminotriethylene oxide chains linked by 1,4- and/or 1,5-disubstituted 1,2,3-triazole rings were prepared from ZnO NPs (ZPA) with ethynyl groups on the surfaces and an azide derivative of triethylene oxide chain linking terminal amino group (ATA) via 1,3-dipolar azide/alkyne click reaction by heating without Cu(I) catalyst. FTIR spectroscopy, elemental analysis, XRD analysis and TEM observation suggested that the resulting ZPA and ZPAZ NPs have the particle sizes below 10 nm in diameters, triethylene oxide chains linking the terminal amino groups and wurtzite crystal structure. UV-vis absorption spectrum of the ZPAZ NPs in methanol showed maximum absorption band at 346.5 nm, supporting the TEM observation. PL spectra depicted that the ZPA and ZPAZ NPs display broad light green and lightly greenish yellow visible light emitting bands in methanol. Zeta potentials measured in distilled water suggested that the ZPAZ NPs have a low tendency to aggregate and possess better stability than the ZPA NPs. Cytotoxicity assay revealed that the ZPAZ NPs, having water-dispersion properties, are noncytotoxic at low concentrations and almost all RAW264.7 cells are alive after 24 h of treatment.

  4. Inulin crystal initiation via a glucose-fructose cross-link of adjacent polymer chains: atomic force microscopy and static molecular modelling.

    Science.gov (United States)

    Cooper, Peter D; Rajapaksha, K Harinda; Barclay, Thomas G; Ginic-Markovic, Milena; Gerson, Andrea R; Petrovsky, Nikolai

    2015-03-06

    Semi-crystalline microparticles of inulin (MPI) have clinical utility as potent human vaccine adjuvants but their relevant surface structure and crystal assembly remain undefined. We show inulin crystal surfaces to resemble multi-layered, discoid radial spherulites resulting from very rapid formation of complex tertiary structures, implying directed crystal initiation. Physical and in silico molecular modelling of unit cells confirm steric feasibility of initiation by hydrogen-bonded cross-linking of terminal glucose to a fructose of another chain, mimicking bonding in sucrose crystals. A strong, chelate-like dual H-bond is proposed to compel the known antiparallel alignment of inulin chains. Such cross-linking would require one extra fructose per chain in the native inulin crystal, as observed. Completion of five H-bonded internal ring-domains would 'lock in' each new 6-fructose structural unit of each antiparallel helix pair to create a new isoform. All known properties of inulin isoforms follow readily from these concepts. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Link between lipid metabolism and voluntary food intake in rainbow trout fed coconut oil rich in medium-chain TAG

    NARCIS (Netherlands)

    Figueiredo-Silva, A.C.; Kaushik, S.; Terrier, F.; Schrama, J.W.; Médale, F.; Geurden, I.

    2012-01-01

    We examined the long-term effect of feeding coconut oil (CO; rich in lauric acid, C12) on voluntary food intake and nutrient utilisation in rainbow trout (Oncorhynchus mykiss), with particular attention to the metabolic use (storage or oxidation) of ingested medium-chain TAG. Trout were fed for 15

  6. Two unique mutations in the interleukin-2 receptor gamma chain gene (IL2RG) cause X-linked severe combined immunodeficiency arising in opposite parental germ lines

    Energy Technology Data Exchange (ETDEWEB)

    Puck, J.M.; Pepper, A.E. [National Institutes of Health, Bethesda, MD (United States)

    1994-09-01

    The gene encoding the gamma chain of the lymphocyte receptor for IL-2 lies in human X13.1 and is mutated in males with X-linked severe combined immunodeficiency (SCID). 27 X-linked SCID mutations have been found in our laboratory. Single strand conformation polymorphism (SSCP) analysis of genomic DNA using primers flanking each of the 8 exons was followed by direct sequencing of abnormally migrating fragments from SCID patients and family members. A 9 bp in-frame duplication insertion was found in IL2RG exon 5 of a patient from a large X-linked SCID pedigree; the resulting duplication of 3 extracellular amino acids, including the first tryptophan of the {open_quotes}WSXWS{close_quotes} cytokine binding motif, is predicted to disrupt interaction of the cytokine receptor chain with its ligand. Genetic linkage studies demonstrated that the grandmaternal X chromosome associated with SCID was contributed to 3 daughters, 2 obligate carriers and 1 woman of unknown status. However, this grandmother`s genomic DNA did not contain the insertion mutation, nor did she have skewed X-chromosome inactivation in her lymphocytes. That both obligate carrier daughters, but not the third daughter, had the insertion proved the grandmother to be a germline mosaic. A second proband had X-linked SCID with a branch point mutation due to substitution of T for A 15 bp 5{prime} of the start of IL2RG exon 3. This mutation resulted in undetectable IL2RG mRNA by Northern blot. Linkage analysis and sequencing of IL2RG DNA in this family proved the mutation to have originated in the germline of the proband`s grandfather, an immunocompetent individual who contributed an X chromosome with normal IL2RG to one daughter and a mutated X to the another.

  7. Fault ride-through enhancement using an enhanced field oriented control technique for converters of grid connected DFIG and STATCOM for different types of faults.

    Science.gov (United States)

    Ananth, D V N; Nagesh Kumar, G V

    2016-05-01

    With increase in electric power demand, transmission lines were forced to operate close to its full load and due to the drastic change in weather conditions, thermal limit is increasing and the system is operating with less security margin. To meet the increased power demand, a doubly fed induction generator (DFIG) based wind generation system is a better alternative. For improving power flow capability and increasing security STATCOM can be adopted. As per modern grid rules, DFIG needs to operate without losing synchronism called low voltage ride through (LVRT) during severe grid faults. Hence, an enhanced field oriented control technique (EFOC) was adopted in Rotor Side Converter of DFIG converter to improve power flow transfer and to improve dynamic and transient stability. A STATCOM is coordinated to the system for obtaining much better stability and enhanced operation during grid fault. For the EFOC technique, rotor flux reference changes its value from synchronous speed to zero during fault for injecting current at the rotor slip frequency. In this process DC-Offset component of flux is controlled, decomposition during symmetric and asymmetric faults. The offset decomposition of flux will be oscillatory in a conventional field oriented control, whereas in EFOC it was aimed to damp quickly. This paper mitigates voltage and limits surge currents to enhance the operation of DFIG during symmetrical and asymmetrical faults. The system performance with different types of faults like single line to ground, double line to ground and triple line to ground was applied and compared without and with a STATCOM occurring at the point of common coupling with fault resistance of a very small value at 0.001Ω. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

  8. Diseño y simulación del control de un compensador sincrónico estático (statcom)

    OpenAIRE

    Aguilar, Daniel; Gavilanes, Luis; Falcones, Síxifo

    2013-01-01

    En el presente proyecto se realiza el diseño del control y simulación de un compensador sincrónico estático (STATCOM) aplicado al punto medio de una línea de transmisión. Se empieza diseñando el sistema de tan manera que cumpla con especificaciones dadas para luego encontrar el modelo usando la teoría de la Transformación dq. Estas funciones de transferencia corresponden al lazo interno, el cual se controla la corriente que entrega el dispositivo, y al lazo externo, que controla el voltaje de...

  9. Inborn Errors of Long-Chain Fatty Acid β-Oxidation Link Neural Stem Cell Self-Renewal to Autism

    Directory of Open Access Journals (Sweden)

    Zhigang Xie

    2016-02-01

    Full Text Available Inborn errors of metabolism (IEMs occur with high incidence in human populations. Especially prevalent among these are inborn deficiencies in fatty acid β-oxidation (FAO, which are clinically associated with developmental neuropsychiatric disorders, including autism. We now report that neural stem cell (NSC-autonomous insufficiencies in the activity of TMLHE (an autism risk factor that supports long-chain FAO by catalyzing carnitine biosynthesis, of CPT1A (an enzyme required for long-chain FAO transport into mitochondria, or of fatty acid mobilization from lipid droplets reduced NSC pools in the mouse embryonic neocortex. Lineage tracing experiments demonstrated that reduced flux through the FAO pathway potentiated NSC symmetric differentiating divisions at the expense of self-renewing stem cell division modes. The collective data reveal a key role for FAO in controlling NSC-to-IPC transition in the mammalian embryonic brain and suggest NSC self renewal as a cellular mechanism underlying the association between IEMs and autism.

  10. Characterization of the native and denatured herceptin by enzyme linked immunosorbent assay and quartz crystal microbalance using a high-affinity single chain fragment variable recombinant antibody.

    Science.gov (United States)

    Shang, Yuqin; Mernaugh, Ray; Zeng, Xiangqun

    2012-10-02

    Herceptin/Trastuzumab is a humanized IgG1κ light chain antibody used to treat some forms of breast cancer. A phage-displayed recombinant antibody library was used to obtain a single chain fragment variable (scFv, designated 2B4) to a linear synthetic peptide representing Herceptin's heavy chain CDR3. Enzyme linked immunosorbent assays (ELISAs) and piezoimmunosensor/quartz crystal microbalance (QCM) assays were used to characterize 2B4-binding activity to both native and heat denatured Herceptin. The 2B4 scFv specifically bound to heat denatured Herceptin in a concentration dependent manner over a wide (35-220.5 nM) dynamic range. Herceptin denatures and forms significant amounts of aggregates when heated. UV-vis characterization confirms that Herceptin forms aggregates as the temperature used to heat Herceptin increases. QCM affinity assay shows that binding stoichiometry between 2B4 scFv and Herceptin follows a 1:2 relationship proving that 2B4 scFv binds strongly to the dimers of heat denatured Herceptin aggregates and exhibits an affinity constant of 7.17 × 10(13) M(-2). The 2B4-based QCM assay was more sensitive than the corresponding ELISA. Combining QCM with ELISA can be used to more fully characterize nonspecific binding events in assays. The potential theoretical and clinical implications of these results and the advantages of the use of QCM to characterize human therapeutic antibodies in samples are also discussed.

  11. Competition between links in "producer-consumer" trophic chains in an aquatic closed system with spatially separated components.

    Science.gov (United States)

    Pisman, T I; Pechurkin, N S; Somova, L A

    2001-01-01

    The work analyzes functioning of a "producer-consumer" closed aquatic system with spatially separated links, where each component consisted of two species. Producers in the system were the microalgae of Chlorella vulgaris and Scenedesmus sp., consumers--Paramecium caudatum infusoria and Brachionus sp. rotifers. In the experiment the competing predators were consuming on a mixed culture of algae, and the competition of algae was studied under nitrogen limitation. Under these conditions competitiveness of Scenedesmus was higher than that of Chlorella vulgaris. Metabolism products of Scenedesmus algae have been found to have negative effect on reproduction of Paramecium caudatum protozoa. Predator population dynamics in the "consumer" link demonstrated that the rotifers that consume two algal species are more competitive compared to protozoa feeding on chlorella only. Grant numbers: N99-04-96017, N25. c 2001. COSPAR. Published by Elsevier Science Ltd. All rights reserved.

  12. Competition between links in ``producer-consumer'' trophic chains in an aquatic closed system with spatially separated components

    Science.gov (United States)

    Pisman, T. I.; Pechurkin, N. S.; Somova, L. A.

    The work analyzes functioning of a "producer-consumer" closed aquatic system with spatially separated links, where each component consisted of two species. Producers in the system were the microalgae of Chlorella vulgaris and Scenedesmus sp., consumers - Paramecium caudatum infusoria and Brachionus sp. rotifers. In the experiment the competing predators were consuming on a mixed culture of algae, and the competition of algae was studied under nitrogen limitation. Under these conditions competitiveness of Scenedesmus was higher than that of Chlorella vulgaris. Metabolism products of Scenedesmus algae have been found to have negative effect on reproduction of Paramecium caudatum protozoa. Predator population dynamics in the "consumer" link demonstrated that the rotifers that consume two algal species are more competitive compared to protozoa feeding on chlorella only.

  13. Human urokinase contains GalNAcβ(1-4)[Fucα(1-3)]GlcNAcα(1-2) as a novel terminal element in N-linked carbohydrate chains

    NARCIS (Netherlands)

    Vliegenthart, J.F.G.; Bergwerff, A.A.; Thomas-Oates, J.E.; Oostrum, J. van; Kamerling, J.P.

    1992-01-01

    Structural analysis of enzymically released N-linked carbohydrate chains of human urokinase (urinary-type plasminogen activator) by 1H NMR spectroscopy and FAB-MS demonstrated that the N-linked oligosaccharides on the only N-glycosylation site contain diantennary structures with the novel Ga1NAc

  14. Evaluating environmental impacts of alternative construction waste management approaches using supply-chain-linked life-cycle analysis.

    Science.gov (United States)

    Kucukvar, Murat; Egilmez, Gokhan; Tatari, Omer

    2014-06-01

    Waste management in construction is critical for the sustainable treatment of building-related construction and demolition (C&D) waste materials, and recycling of these wastes has been considered as one of the best strategies in minimization of C&D debris. However, recycling of C&D materials may not always be a feasible strategy for every waste type and therefore recycling and other waste treatment strategies should be supported by robust decision-making models. With the aim of assessing the net carbon, energy, and water footprints of C&D recycling and other waste management alternatives, a comprehensive economic input-output-based hybrid life-cycle assessment model is developed by tracing all of the economy-wide supply-chain impacts of three waste management strategies: recycling, landfilling, and incineration. Analysis results showed that only the recycling of construction materials provided positive environmental footprint savings in terms of carbon, energy, and water footprints. Incineration is a better option as a secondary strategy after recycling for water and energy footprint categories, whereas landfilling is found to be as slightly better strategy when carbon footprint is considered as the main focus of comparison. In terms of construction materials' environmental footprint, nonferrous metals are found to have a significant environmental footprint reduction potential if recycled. © The Author(s) 2014.

  15. Single chain variable fragment antibodies block aggregation and toxicity induced by familial ALS-linked mutant forms of SOD1.

    Science.gov (United States)

    Ghadge, Ghanashyam D; Pavlovic, John D; Koduvayur, Sujatha P; Kay, Brian K; Roos, Raymond P

    2013-08-01

    Approximately 10% of amyotrophic lateral sclerosis (ALS) cases are familial (known as FALS) with an autosomal dominant inheritance pattern, and ~25% of FALS cases are caused by mutations in Cu/Zn superoxide dismutase (SOD1). There is convincing evidence that mutant SOD1 (mtSOD1) kills motor neurons (MNs) because of a gain-of-function toxicity, most likely related to aggregation of mtSOD1. A number of recent reports have suggested that antibodies can be used to treat mtSOD1-induced FALS. To follow up on the use of antibodies as potential therapeutics, we generated single chain fragments of variable region antibodies (scFvs) against SOD1, and then expressed them as 'intrabodies' within a motor neuron cell line. In the present study, we describe isolation of human scFvs that interfere with mtSOD1 in vitro aggregation and toxicity. These scFvs may have therapeutic potential in sporadic ALS, as well as FALS, given that sporadic ALS may also involve abnormalities in the SOD1 protein or activity. Copyright © 2013 Elsevier Inc. All rights reserved.

  16. A LINK TO THE PAST: USING MARKOV CHAIN MONTE CARLO FITTING TO CONSTRAIN FUNDAMENTAL PARAMETERS OF HIGH-REDSHIFT GALAXIES

    Energy Technology Data Exchange (ETDEWEB)

    Pirzkal, N.; Rothberg, B.; Koekemoer, Anton [Space Telescope Science Institute, 3700 San Martin Drive, Baltimore, MD 21218 (United States); Nilsson, Kim K. [ST-ECF, Karl-Schwarzschild-Strasse 2, 85748 Garching bei Muenchen (Germany); Finkelstein, S. [George P. and Cynthia Woods Mitchell Institute for Fundamental Physics and Astronomy, Department of Physics and Astronomy, Texas A and M University, College Station, TX 77843 (United States); Malhotra, Sangeeta; Rhoads, James, E-mail: npirzkal@stsci.edu [School of Earth and Space Exploration, Arizona State University, P.O. Box 871404, Tempe, AZ 85287-1404 (United States)

    2012-04-01

    We have developed a new method for fitting spectral energy distributions (SEDs) to identify and constrain the physical properties of high-redshift (4 < z < 8) galaxies. Our approach uses an implementation of Bayesian based Markov Chain Monte Carlo that we have dubbed '{pi}MC{sup 2}'. It allows us to compare observations to arbitrarily complex models and to compute 95% credible intervals that provide robust constraints for the model parameters. The work is presented in two sections. In the first, we test {pi}MC{sup 2} using simulated SEDs to not only confirm the recovery of the known inputs but to assess the limitations of the method and identify potential hazards of SED fitting when applied specifically to high-redshift (z > 4) galaxies. In the second part of the paper we apply {pi}MC{sup 2} to thirty-three 4 < z < 8 objects, including the spectroscopically confirmed Grism ACS Program for Extragalactic Science Ly{alpha} sample (4 < z < 6), supplemented by newly obtained Hubble Space Telescope/WFC3 near-IR observations, and several recently reported broadband selected z > 6 galaxies. Using {pi}MC{sup 2}, we are able to constrain the stellar mass of these objects and in some cases their stellar age and find no evidence that any of these sources formed at a redshift larger than z = 8, a time when the universe was Almost-Equal-To 0.6 Gyr old.

  17. Relative efficiency of polymerase chain reaction and enzyme-linked immunosorbant assay in determination of viral etiology in congenital cataract in infants

    Directory of Open Access Journals (Sweden)

    Shyamala G

    2008-01-01

    Full Text Available Background: Perinatal viral infections of fetus are among the leading causes of congenital cataract and identifying the viral etiology is important. Objectives: To detect the presence of Rubella virus (RV, herpes simplex virus (HSV and cytomegalovirus (CMV in lens aspirate specimens obtained from patients with congenital cataract and relate the results with serology. Setting and Design: Prospective study carried out in tertiary care hospital. Materials and Methods: Fifty lens aspirates from 50 infants with congenital cataract were subjected to HSV, RV isolation and polymerase chain reaction (PCR for detection of HSV and CMV. Reverse transcription polymerase chain reaction (RT-PCR was applied for RV detection. Peripheral blood specimens were screened for anti-HSV, RV and CMV antibodies by enzyme-linked immunosorbant assay (ELISA. Results: Rubella virus was detected in nine (18% lens aspirates, by nRT-PCR which includes six positive by culture. HSV-2 DNA was detected in nine other lens aspirates, while CMV was not detected by PCR. Serological results did not correlate with the presence of viruses in the lens aspirates. This is the first report of detection of HSV-2 DNA in cases of congenital cataract. Conclusions: Cytomegalovirus may not be playing a significant role in causation of congenital cataract. The role of serology in identifying causative viral infection for congenital cataract needs to be re-evaluated.

  18. Standard handbook of chains chains for power transmission and material handling

    CERN Document Server

    2005-01-01

    A BRIEF HISTORY OF THE DEVELOPMENT OF CHAINEarly DevelopmentsCog ChainCast Detachable ChainCast Pintle ChainPrecision Roller ChainEngineering Steel ChainSilent ChainFlat-Top ChainTerminologyA CHAIN OVERVIEW: USES AND ADVANTAGESGeneralTypes of ChainScope of Chains CoveredStyles and Forms of ChainsStraight and Offset Link ChainsChains With and Without RollersUses of ChainStandard Chains and Their UsesThe Advantages of Chains in ApplicationsAdvantages of Roller Chains in DrivesAdvantages of Silent Chain Drives

  19. Expanding the first link in the chain of survival - Experiences from dispatcher referral of callers to AED locations.

    Science.gov (United States)

    Fredman, David; Svensson, Leif; Ban, Yifang; Jonsson, Martin; Hollenberg, Jacob; Nordberg, Per; Ringh, Mattias; Rosenqvist, Mårten; Lundén, Margareta; Claesson, Andreas

    2016-10-01

    Early use of automated external defibrillators (AED) increases survival in cases of out-of-hospital cardiac arrest (OHCA). Dispatchers play important roles in identifying OHCA, dispatching ambulances and providing callers with telephone-assisted cardiopulmonary resuscitation. Guidelines recommend that AED registries be linked to dispatch centres as tools to refer callers to nearby AED. The aim of this study was to investigate to what extent dispatchers, when provided with a tool to display AED locations and accessibility, referred callers to nearby AED. An application providing real-time visualization of AED locations and accessibility was implemented at four dispatch centres in Sweden. Dispatchers were instructed to refer callers to nearby AED when OHCA was suspected. Such cases were prospectively collected, and geographic information systems were used to identify those located ≤100m from an AED. Audio recordings of emergency calls were assessed to evaluate the AED referral rate. Between February and August 2014, 3009 suspected OHCA calls were received. In 6.6% of those calls (200/3009), an AED was ≤100m from the suspected OHCA. The AED was accessible and the caller was not alone on scene in 24% (47/200) of these cases. In two of those 47 cases (4.3%), the dispatcher referred the caller to the AED. Despite a tool for dispatchers to refer callers to a nearby AED, referral was rare. Only a minority of the suspected OHCA cases occurred ≤100m from an AED. We identified AED accessibility and callers being alone on scene as obstacles for AED referral. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  20. HTLV-1 Tax Stimulates Ubiquitin E3 Ligase, Ring Finger Protein 8, to Assemble Lysine 63-Linked Polyubiquitin Chains for TAK1 and IKK Activation.

    Directory of Open Access Journals (Sweden)

    Yik-Khuan Ho

    2015-08-01

    Full Text Available Human T lymphotropic virus type 1 (HTLV-1 trans-activator/oncoprotein, Tax, impacts a multitude of cellular processes, including I-κB kinase (IKK/NF-κB signaling, DNA damage repair, and mitosis. These activities of Tax have been implicated in the development of adult T-cell leukemia (ATL in HTLV-1-infected individuals, but the underlying mechanisms remain obscure. IKK and its upstream kinase, TGFβ-activated kinase 1 (TAK1, contain ubiquitin-binding subunits, NEMO and TAB2/3 respectively, which interact with K63-linked polyubiquitin (K63-pUb chains. Recruitment to K63-pUb allows cross auto-phosphorylation and activation of TAK1 to occur, followed by TAK1-catalyzed IKK phosphorylation and activation. Using cytosolic extracts of HeLa and Jurkat T cells supplemented with purified proteins we have identified ubiquitin E3 ligase, ring finger protein 8 (RNF8, and E2 conjugating enzymes, Ubc13:Uev1A and Ubc13:Uev2, to be the cellular factors utilized by Tax for TAK1 and IKK activation. In vitro, the combination of Tax and RNF8 greatly stimulated TAK1, IKK, IκBα and JNK phosphorylation. In vivo, RNF8 over-expression augmented while RNF8 ablation drastically reduced canonical NF-κB activation by Tax. Activation of the non-canonical NF-κB pathway by Tax, however, is unaffected by the loss of RNF8. Using purified components, we further demonstrated biochemically that Tax greatly stimulated RNF8 and Ubc13:Uev1A/Uev2 to assemble long K63-pUb chains. Finally, co-transfection of Tax with increasing amounts of RNF8 greatly induced K63-pUb assembly in a dose-dependent manner. Thus, Tax targets RNF8 and Ubc13:Uev1A/Uev2 to promote the assembly of K63-pUb chains, which signal the activation of TAK1 and multiple downstream kinases including IKK and JNK. Because of the roles RNF8 and K63-pUb chains play in DNA damage repair and cytokinesis, this mechanism may also explain the genomic instability of HTLV-1-transformed T cells and ATL cells.

  1. HTLV-1 Tax Stimulates Ubiquitin E3 Ligase, Ring Finger Protein 8, to Assemble Lysine 63-Linked Polyubiquitin Chains for TAK1 and IKK Activation.

    Science.gov (United States)

    Ho, Yik-Khuan; Zhi, Huijun; Bowlin, Tara; Dorjbal, Batsukh; Philip, Subha; Zahoor, Muhammad Atif; Shih, Hsiu-Ming; Semmes, Oliver John; Schaefer, Brian; Glover, J N Mark; Giam, Chou-Zen

    2015-08-01

    Human T lymphotropic virus type 1 (HTLV-1) trans-activator/oncoprotein, Tax, impacts a multitude of cellular processes, including I-κB kinase (IKK)/NF-κB signaling, DNA damage repair, and mitosis. These activities of Tax have been implicated in the development of adult T-cell leukemia (ATL) in HTLV-1-infected individuals, but the underlying mechanisms remain obscure. IKK and its upstream kinase, TGFβ-activated kinase 1 (TAK1), contain ubiquitin-binding subunits, NEMO and TAB2/3 respectively, which interact with K63-linked polyubiquitin (K63-pUb) chains. Recruitment to K63-pUb allows cross auto-phosphorylation and activation of TAK1 to occur, followed by TAK1-catalyzed IKK phosphorylation and activation. Using cytosolic extracts of HeLa and Jurkat T cells supplemented with purified proteins we have identified ubiquitin E3 ligase, ring finger protein 8 (RNF8), and E2 conjugating enzymes, Ubc13:Uev1A and Ubc13:Uev2, to be the cellular factors utilized by Tax for TAK1 and IKK activation. In vitro, the combination of Tax and RNF8 greatly stimulated TAK1, IKK, IκBα and JNK phosphorylation. In vivo, RNF8 over-expression augmented while RNF8 ablation drastically reduced canonical NF-κB activation by Tax. Activation of the non-canonical NF-κB pathway by Tax, however, is unaffected by the loss of RNF8. Using purified components, we further demonstrated biochemically that Tax greatly stimulated RNF8 and Ubc13:Uev1A/Uev2 to assemble long K63-pUb chains. Finally, co-transfection of Tax with increasing amounts of RNF8 greatly induced K63-pUb assembly in a dose-dependent manner. Thus, Tax targets RNF8 and Ubc13:Uev1A/Uev2 to promote the assembly of K63-pUb chains, which signal the activation of TAK1 and multiple downstream kinases including IKK and JNK. Because of the roles RNF8 and K63-pUb chains play in DNA damage repair and cytokinesis, this mechanism may also explain the genomic instability of HTLV-1-transformed T cells and ATL cells.

  2. Effect of ageing and ischemia on enzymatic activities linked to Krebs' cycle, electron transfer chain, glutamate and aminoacids metabolism of free and intrasynaptic mitochondria of cerebral cortex.

    Science.gov (United States)

    Villa, Roberto Federico; Gorini, Antonella; Hoyer, Siegfried

    2009-12-01

    The effect of ageing and the relationships between the catalytic properties of enzymes linked to Krebs' cycle, electron transfer chain, glutamate and aminoacid metabolism of cerebral cortex, a functional area very sensitive to both age and ischemia, were studied on mitochondria of adult and aged rats, after complete ischemia of 15 minutes duration. The maximum rate (Vmax) of the following enzyme activities: citrate synthase, malate dehydrogenase, succinate dehydrogenase for Krebs' cycle; NADH-cytochrome c reductase as total (integrated activity of Complex I-III), rotenone sensitive (Complex I) and cytochrome oxidase (Complex IV) for electron transfer chain; glutamate dehydrogenase, glutamate-oxaloacetate-and glutamate-pyruvate transaminases for glutamate metabolism were assayed in non-synaptic, perikaryal mitochondria and in two populations of intra-synaptic mitochondria, i.e., the light and heavy mitochondrial fraction. The results indicate that in normal, steady-state cerebral cortex, the value of the same enzyme activity markedly differs according (a) to the different populations of mitochondria, i.e., non-synaptic or intra-synaptic light and heavy, (b) and respect to ageing. After 15 min of complete ischemia, the enzyme activities of mitochondria located near the nucleus (perikaryal mitochondria) and in synaptic structures (intra-synaptic mitochondria) of the cerebral tissue were substantially modified by ischemia. Non-synaptic mitochondria seem to be more affected by ischemia in adult and particularly in aged animals than the intra-synaptic light and heavy mitochondria. The observed modifications in enzyme activities reflect the metabolic state of the tissue at each specific experimental condition, as shown by comparative evaluation with respect to the content of energy-linked metabolites and substrates. The derangements in enzyme activities due to ischemia is greater in aged than in adult animals and especially the non-synaptic and the intra-synaptic light

  3. Outbreak of human Salmonella Typhimurium infections linked to contact with baby poultry from a single agricultural feed store chain and mail-order hatchery, 2009.

    Science.gov (United States)

    Loharikar, Anagha; Vawter, Shannon; Warren, Kim; Deasy, Marshall; Moll, Maria; Sandt, Carol; Gilhousen, Renee; Villamil, Elizabeth; Rhorer, Andrew; Briere, Elizabeth; Schwensohn, Colin; Trees, Eija; Lafon, Patricia; Adams, Jennifer Kincaid; Le, Brenda; Behravesh, Casey Barton

    2013-01-01

    Over 30 outbreaks of human salmonellosis linked to contact with live poultry from mail-order hatcheries were reported to Centers for Disease Control and Prevention between 1990 and 2010. In May 2009, we investigated an outbreak of human Salmonella Typhimurium infections, primarily affecting children. A case was defined as a person with the outbreak strain of Salmonella Typhimurium, as determined by pulsed-field gel electrophoresis and multiple-locus variable-number tandem repeat analysis, in a Pennsylvania or New York resident with illness onset between May 1 and September 1, 2009. We conducted a case-control study to examine the relationship between illness and live poultry contact. Controls were age-matched and geographically-matched. Traceback and environmental investigations were conducted. We identified 36 case-patients in Pennsylvania and New York; 36% were children aged ≤5 years. Case-patients were more likely than controls to report live baby poultry contact (matched odds ratio [mOR]: 17.0; 95% confidence interval [CI]: 2.7-710.5), contact with chicks (mOR: 14.0; 95% CI: 2.1-592.0), ducklings (mOR: 8.0; 95% CI: 1.1-355.0) and visiting agricultural feed stores (mOR: 6.0; 95% CI: 1.3-55.2). Most (83%) visited agricultural Feed Store Chain Y, a national agricultural feed store chain, which received poultry from Hatchery C, which is supplied by multiple egg sources. Salmonella Typhimurium was isolated from a source duck flock, but had a different pulsed-field gel electrophoresis pattern than the outbreak strain. Live baby poultry remain an important source of human salmonellosis, particularly among children. Preventing these infections requires comprehensive interventions at hatcheries and agricultural feed stores; pediatricians should inform patients of risks associated with live poultry contact.

  4. Associations of IgG N-linked oligosaccharide chains and proteases in sera of prostate cancer patients with and without alpha2-macroglobulin deficiency.

    Science.gov (United States)

    Kanoh, Yuhsaku; Egawa, Shin; Baba, Shiro; Akahoshi, Tohru

    2009-01-01

    We previously reported on a number of cases of metastatic prostate cancer (PCa) in which serum alpha2-macroglobulin (alpha2M) levels were markedly decreased to less than 20 mg/dl (alpha2M deficiency). All PCa patients with alpha2M deficiency had multiple bone metastases. Proteases in ten PCa patients with and without alpha2M deficiency were studied and compared against ten healthy controls in order to elucidate the relationships between changes in sugar chain structure and neoplasia. We assessed the relationship between ratios of Fr4 to Fr1 and Fr2 (Fr4/Fr1+Fr2 ratios) of oligosaccharide chains, and ratios of free prostate-specific antigen (PSA) to total PSA (F/T ratios), and serum levels of matrix-metalloproteinase-2 (MMP-2) in PCa progression. Measurement of serum alpha2M concentration was performed by laser nephelometry. Serum PSA and MMP-2 levels were determined by enzyme immunoassay and free PSA by radioimmunoassay. N-linked oligosaccharides of human serum immunoglobulin G were analyzed using fluorophore-associated carbohydrate electrophoresis. In those PCa patients with alpha2M deficiency: (a) serum alpha2M and F/T ratios were lower (Pdeficiency. There was a significant correlation between Fr4/Fr1+Fr2 ratios and F/T ratios or serum MMP-2 levels in PCa with alpha2M deficiency (P<0.05). Therefore, these markers may serve as an auxiliary serum tumor marker for monitoring of the bone metastases or progression of disease in PCa. (c) 2009 Wiley-Liss, Inc.

  5. Impaired very long-chain acyl-CoA β-oxidation in human X-linked adrenoleukodystrophy fibroblasts is a direct consequence of ABCD1 transporter dysfunction.

    Science.gov (United States)

    Wiesinger, Christoph; Kunze, Markus; Regelsberger, Günther; Forss-Petter, Sonja; Berger, Johannes

    2013-06-28

    X-linked adrenoleukodystrophy (X-ALD), an inherited peroxisomal disorder, is caused by mutations in the ABCD1 gene encoding the peroxisomal ATP-binding cassette (ABC) transporter ABCD1 (adrenoleukodystrophy protein, ALDP). Biochemically, X-ALD is characterized by an accumulation of very long-chain fatty acids and partially impaired peroxisomal β-oxidation. In this study, we used primary human fibroblasts from X-ALD and Zellweger syndrome patients to investigate the peroxisomal β-oxidation defect. Our results show that the degradation of C26:0-CoA esters is as severely impaired as degradation of unesterified very long-chain fatty acids in X-ALD and is abolished in Zellweger syndrome. Interestingly, the β-oxidation rates for both C26:0-CoA and C22:0-CoA were similarly affected, although C22:0 does not accumulate in patient fibroblasts. Furthermore, we show that the β-oxidation defect in X-ALD is directly caused by ABCD1 dysfunction as blocking ABCD1 function with a specific antibody reduced β-oxidation to levels observed in X-ALD fibroblasts. By quantification of mRNA and protein levels of the peroxisomal ABC transporters and by blocking with specific antibodies, we found that residual β-oxidation activity toward C26:0-CoA in X-ALD fibroblasts is mediated by ABCD3, although the efficacy of ABCD3 appeared to be much lower than that of ABCD1. Finally, using isolated peroxisomes, we show that β-oxidation of C26:0-CoA is independent of additional CoA but requires a cytosolic factor of >10-kDa molecular mass that is resistant to N-ethylmaleimide and heat inactivation. In conclusion, our findings in human cells suggest that, in contrast to yeast cells, very long-chain acyl-CoA esters are transported into peroxisomes by ABCD1 independently of additional synthetase activity.

  6. Impaired Very Long-chain Acyl-CoA β-Oxidation in Human X-linked Adrenoleukodystrophy Fibroblasts Is a Direct Consequence of ABCD1 Transporter Dysfunction*

    Science.gov (United States)

    Wiesinger, Christoph; Kunze, Markus; Regelsberger, Günther; Forss-Petter, Sonja; Berger, Johannes

    2013-01-01

    X-linked adrenoleukodystrophy (X-ALD), an inherited peroxisomal disorder, is caused by mutations in the ABCD1 gene encoding the peroxisomal ATP-binding cassette (ABC) transporter ABCD1 (adrenoleukodystrophy protein, ALDP). Biochemically, X-ALD is characterized by an accumulation of very long-chain fatty acids and partially impaired peroxisomal β-oxidation. In this study, we used primary human fibroblasts from X-ALD and Zellweger syndrome patients to investigate the peroxisomal β-oxidation defect. Our results show that the degradation of C26:0-CoA esters is as severely impaired as degradation of unesterified very long-chain fatty acids in X-ALD and is abolished in Zellweger syndrome. Interestingly, the β-oxidation rates for both C26:0-CoA and C22:0-CoA were similarly affected, although C22:0 does not accumulate in patient fibroblasts. Furthermore, we show that the β-oxidation defect in X-ALD is directly caused by ABCD1 dysfunction as blocking ABCD1 function with a specific antibody reduced β-oxidation to levels observed in X-ALD fibroblasts. By quantification of mRNA and protein levels of the peroxisomal ABC transporters and by blocking with specific antibodies, we found that residual β-oxidation activity toward C26:0-CoA in X-ALD fibroblasts is mediated by ABCD3, although the efficacy of ABCD3 appeared to be much lower than that of ABCD1. Finally, using isolated peroxisomes, we show that β-oxidation of C26:0-CoA is independent of additional CoA but requires a cytosolic factor of >10-kDa molecular mass that is resistant to N-ethylmaleimide and heat inactivation. In conclusion, our findings in human cells suggest that, in contrast to yeast cells, very long-chain acyl-CoA esters are transported into peroxisomes by ABCD1 independently of additional synthetase activity. PMID:23671276

  7. A single-phase multi-level D-STATCOM inverter using modular multi-level converter (MMC) topology for renewable energy sources

    Science.gov (United States)

    Sotoodeh, Pedram

    This dissertation presents the design of a novel multi-level inverter with FACTS capability for small to mid-size (10-20kW) permanent-magnet wind installations using modular multi-level converter (MMC) topology. The aim of the work is to design a new type of inverter with D-STATCOM option to provide utilities with more control on active and reactive power transfer of distribution lines. The inverter is placed between the renewable energy source, specifically a wind turbine, and the distribution grid in order to fix the power factor of the grid at a target value, regardless of wind speed, by regulating active and reactive power required by the grid. The inverter is capable of controlling active and reactive power by controlling the phase angle and modulation index, respectively. The unique contribution of the proposed work is to combine the two concepts of inverter and D-STATCOM using a novel voltage source converter (VSC) multi-level topology in a single unit without additional cost. Simulations of the proposed inverter, with 5 and 11 levels, have been conducted in MATLAB/Simulink for two systems including 20 kW/kVAR and 250 W/VAR. To validate the simulation results, a scaled version (250 kW/kVAR) of the proposed inverter with 5 and 11 levels has been built and tested in the laboratory. Experimental results show that the reduced-scale 5- and 11-level inverter is able to fix PF of the grid as well as being compatible with IEEE standards. Furthermore, total cost of the prototype models, which is one of the major objectives of this research, is comparable with market prices.

  8. Commercial enzyme-linked immunosorbent assay versus polymerase chain reaction for the diagnosis of chronic Chagas disease: a systematic review and meta-analysis

    Science.gov (United States)

    do Brasil, Pedro Emmanuel Alvarenga Americano; Castro, Rodolfo; de Castro, Liane

    2016-01-01

    Chronic Chagas disease diagnosis relies on laboratory tests due to its clinical characteristics. The aim of this research was to review commercial enzyme-linked immunosorbent assay (ELISA) and polymerase chain reaction (PCR) diagnostic test performance. Performance of commercial ELISA or PCR for the diagnosis of chronic Chagas disease were systematically searched in PubMed, Scopus, Embase, ISI Web, and LILACS through the bibliography from 1980-2014 and by contact with the manufacturers. The risk of bias was assessed with QUADAS-2. Heterogeneity was estimated with the I2 statistic. Accuracies provided by the manufacturers usually overestimate the accuracy provided by academia. The risk of bias is high in most tests and in most QUADAS dimensions. Heterogeneity is high in either sensitivity, specificity, or both. The evidence regarding commercial ELISA and ELISA-rec sensitivity and specificity indicates that there is overestimation. The current recommendation to use two simultaneous serological tests can be supported by the risk of bias analysis and the amount of heterogeneity but not by the observed accuracies. The usefulness of PCR tests are debatable and health care providers should not order them on a routine basis. PCR may be used in selected cases due to its potential to detect seronegative subjects. PMID:26814640

  9. Modelamiento y análisis de pequeña señal de un generador de inducción y un STATCOM conectados a un sistema de potencia

    Directory of Open Access Journals (Sweden)

    Carlos David Zuluaga Ríos

    2011-12-01

    Full Text Available This paper presents the modeling and small-signal analysis of an induction generator (IG and a static synchronous compensator (STATCOM connected to an inÞ nite bus bar, representing a power system, the IG is modeled as Þ fth-order system and is coupled to a STATCOM is studied as a model of Þ rst order. The dynamic behaviorwas simulated and compared using MATLAB/ Simulink, two conditions of disturbance: a variation in the torque of the machine and a variationin the inÞ nite bus bar voltage because of a failure at this point. The responses obtained by the software show that the compensator acts appropriately counteracting power and voltage variations. Significantly, it must add a stage of tuning parameters to improve the responses.

  10. Electron Transport Chain Is Biochemically Linked to Pilus Assembly Required for Polymicrobial Interactions and Biofilm Formation in the Gram-Positive Actinobacterium Actinomyces oris

    Directory of Open Access Journals (Sweden)

    Belkys C. Sanchez

    2017-06-01

    Full Text Available The Gram-positive actinobacteria Actinomyces spp. are key colonizers in the development of oral biofilms due to the inherent ability of Actinomyces to adhere to receptor polysaccharides on the surface of oral streptococci and host cells. This receptor-dependent bacterial interaction, or coaggregation, requires a unique sortase-catalyzed pilus consisting of the pilus shaft FimA and the coaggregation factor CafA forming the pilus tip. While the essential role of the sortase machine SrtC2 in pilus assembly, biofilm formation, and coaggregation has been established, little is known about trans-acting factors contributing to these processes. We report here a large-scale Tn5 transposon screen for mutants defective in Actinomyces oris coaggregation with Streptococcus oralis. We obtained 33 independent clones, 13 of which completely failed to aggregate with S. oralis, and the remainder of which exhibited a range of phenotypes from severely to weakly defective coaggregation. The former had Tn5 insertions in fimA, cafA, or srtC2, as expected; the latter were mapped to genes coding for uncharacterized proteins and various nuo genes encoding the NADH dehydrogenase subunits. Electron microscopy and biochemical analyses of mutants with nonpolar deletions of nuo genes and ubiE, a menaquinone C-methyltransferase-encoding gene downstream of the nuo locus, confirmed the pilus and coaggregation defects. Both nuoA and ubiE mutants were defective in oxidation of MdbA, the major oxidoreductase required for oxidative folding of pilus proteins. Furthermore, supplementation of the ubiE mutant with exogenous menaquinone-4 rescued the cell growth and pilus defects. Altogether, we propose that the A. oris electron transport chain is biochemically linked to pilus assembly via oxidative protein folding.

  11. The usefulness of direct agglutination test, enzyme-linked immunosorbent assay and polymerase chain reaction for the detection of Toxoplasma gondii in wild animals.

    Science.gov (United States)

    Kornacka, Aleksandra; Cybulska, Aleksandra; Bień, Justyna; Goździk, Katarzyna; Moskwa, Bożena

    2016-09-15

    The aim of the study was to compare the usefulness of two antibody-based methods, the direct agglutination test (DAT) and enzyme linked immuosorbent assay (ELISA), with that of the polymerase chain reaction (PCR) for detecting anti-Toxoplasma gondii in samples derived from naturally-infected wild animals. Antibodies against T. gondii were detected in meat juice samples collected from 129 free- living carnivores and omnivores. T. gondii seroprevalence was confirmed in 73,6% of examined samples when DAT and ELISA were used separately, but in only 88,4% samples when both immunological tests were used in parallel. PCR results confirmed the presence of DNA of the parasite in 24 of all the 129 samples. Sixteen samples were classified as positive when all three tests were used. A moderate degree of agreement was found between DAT and ELISA (κ=0.55). However, no agreement was found between the molecular and serological tests: κ=-1.75 for DAT versus PCR; κ=-1.67 ELISA versus PCR. By using both serological tests, antibodies against T. gondii were found in 77.5% of red foxes, 12.5% of badgers, 40% of martens and 8.3% of raccoon dogs. Antibodies against the parasite were detected also in one mink, but not in the sample derived from a polecat. T.gondii DNA was found in the brain tissue of 20 red foxes, three badgers and one raccoon dog. Our studies confirm that ELISA and DAT are suitable and reliable techniques for T. gondii antibody detection in meat juice from wild animals when serum samples are unavailable. Positive results obtained by immunological tests do not always reflect that the host was infected by T. gondii. They indicate only a contact with parasite. PCR should be used to confirm te presence of DNA from T. gondii. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. ALTERNATE FOOD-CHAIN TRANSFER OF THE TOXIN LINKED TO AVIAN VACUOLAR MYELINOPATHY AND IMPLICATIONS FOR THE ENDANGERED FLORIDA SNAIL KITE (ROSTRHAMUS SOCIABILIS).

    Science.gov (United States)

    Dodd, Shelley R; Haynie, Rebecca S; Williams, Susan M; Wilde, Susan B

    2016-04-28

    Avian vacuolar myelinopathy (AVM) is a neurologic disease causing recurrent mortality of Bald Eagles ( Haliaeetus leucocephalus ) and American Coots ( Fulica americana ) at reservoirs and small impoundments in the southern US. Since 1994, AVM is considered the cause of death for over 170 Bald Eagles and thousands of American Coots and other species of wild birds. Previous studies link the disease to an uncharacterized toxin produced by a recently described cyanobacterium, Aetokthonos hydrillicola gen. et sp. nov. that grows epiphytically on submerged aquatic vegetation (SAV). The toxin accumulates, likely in the gastrointestinal tract of waterbirds that consume SAV, and birds of prey are exposed when feeding on the moribund waterbirds. Aetokthonos hydrillicola has been identified in all reservoirs where AVM deaths have occurred and was identified growing abundantly on an exotic SAV hydrilla ( Hydrilla verticillata ) in Lake Tohopekaliga (Toho) in central Florida. Toho supports a breeding population of a federally endangered raptor, the Florida Snail Kite ( Rostrhamus sociabilis ) and a dense infestation of an exotic herbivorous aquatic snail, the island applesnail ( Pomacea maculata ), a primary source of food for resident Snail Kites. We investigated the potential for transmission in a new food chain and, in laboratory feeding trials, confirmed that the AVM toxin was present in the hydrilla/A. hydrillicola matrix collected from Toho. Additionally, laboratory birds that were fed apple snails feeding on hydrilla/A. hydrillicola material from a confirmed AVM site displayed clinical signs (3/5), and all five developed brain lesions unique to AVM. This documentation of AVM toxin in central Florida and the demonstration of AVM toxin transfer through invertebrates indicate a significant risk to the already diminished population of endangered Snail Kites.

  13. Linked alternating forms and linked symplectic Grassmannians

    OpenAIRE

    Osserman, Brian; Bigas, Montserrat Teixidor I.

    2011-01-01

    Motivated by applications to higher-rank Brill-Noether theory and the Bertram-Feinberg-Mukai conjecture, we introduce the concepts of linked alternating and linked symplectic forms on a chain of vector bundles, and show that the linked symplectic Grassmannians parametrizing chains of subbundles isotropic for a given linked symplectic form has good dimensional behavior analogous to that of the classical symplectic Grassmannian.

  14. (statcom) in synchronous compensator

    African Journals Online (AJOL)

    eobe

    for adoption of advanced control technologies such as Flexible Alternating Current Transmission System (FACTS) with fast response and low cost for stabilizing ... Nigerian Journal of Technology (NIJOTECH). Vol. 34 No. 3, July 2015, pp. 564 – 572 ..... Engineering, Pärnu, Estonia, 10-15. [11] Khederzadeh, M and Ghorbani, ...

  15. (statcom) in synchronous compensator

    African Journals Online (AJOL)

    eobe

    The conventional and modified Newton bus power system. The conventional and modified Newton-Raphson-based power flow equations based power flow equations describing the steady state conditions before and after compensation was made to the system were presented. Solutions to the developed equations were ...

  16. Links between the discovery of primates and anatomical comparisons with humans, the chain of being, our place in nature, and racism.

    Science.gov (United States)

    Diogo, Rui

    2017-12-01

    I focus on the crucial links between the discovery of nonhuman primates by Westerners, discussions on our place in nature, the chain of being, racism, and the history of primate comparative anatomy and of so-called "anatomical human racial studies." Strikingly, for more than a millennium humans knew more about the internal anatomy of a single monkey species than about that of their own bodies. This is because Galen used monkeys to infer human anatomy, in line with the human-animal continuity implied by the Greek notion of scala naturae. With the rise of Christianity, nonhuman primates were increasingly seen in a negative way. A more positive view emerged in the 14th century when nonhuman primates were directly studied/seen by Europeans, culminating in Tyson's 1699 work showing that chimps share more gross anatomical similarities with humans than with monkeys. However, the discomfort caused by this human-chimp similarity then led to a new idea of animal-human discontinuity, now related not to anatomy but to "civilization": between Europeans vs. non-Europeans + other primates. Moreover, Linnaeus' Systema Naturae and the emergence of "anatomical racial studies" influenced by Camper's craniology then led to even more extreme ideas, such as the notion that Europeans were both mentally and morphologically "ideal." Unfortunately the biased and often incorrect "results" of such studies, combined with ideas based on Darwin's "struggle for survival", became crucial in propaganda that lead to the rise of eugenics in the end of the 19th/first half of 20th centuries and that culminated in Nazism. Since the 1950s there has been an emphasis on the continuity/unity between all human groups and other primates, in great part influenced by what happened during World War 2. Reviews such as this one are, therefore, particularly necessary to illuminate and guard against attitudes against "the Other" and racist ideologies that are re-emerging in modern political discourse across the

  17. Synthesis of Peptides from α- and β-Tubulin Containing Glutamic Acid Side-Chain Linked Oligo-Glu with Defined Length

    Directory of Open Access Journals (Sweden)

    Werner Tegge

    2010-01-01

    Full Text Available Side-chain oligo- and polyglutamylation represents an important posttranslational modification in tubulin physiology. The particular number of glutamate units is related to specific regulatory functions. In this work, we present a method for the synthesis of building blocks for the Fmoc synthesis of peptides containing main chain glutamic acid residues that carry side-chain branching with oligo-glutamic acid. The two model peptide sequences CYEEVGVDSVEGEG-E(E-EEGEEY and CQDATADEQG-E(E-FEEEEGEDEA from the C-termini of mammalian α1- and β1-tubulin, respectively, containing oligo-glutamic acid side-chain branching with lengths of 1 to 5 amino acids were assembled in good yield and purity. The products may lead to the generation of specific antibodies which should be important tools for a more detailed investigation of polyglutamylation processes.

  18. La cadena de suministro del sector metalúrgico: un análisis de sus principales eslabones (The Supply Chain in the metallurgical sector: an analysis of the main links

    Directory of Open Access Journals (Sweden)

    Patricia Carbajo-de-Lera

    2011-12-01

    Full Text Available Los directivos actuales conciben que la competencia ya no es empresa frente a empresa, sino que desborda este plano generándose una competencia cadena de suministro frente a cadena de suministro. Por ello, la gestión de la cadena de suministro se convierte en un elemento clave para la supervivencia empresarial y la obtención de ventajas competitivas. El diseño de la cadena de suministro viene definido, en buena parte, por las características del sector al que pertenece. En consecuencia, es de interés realizar análisis sectoriales. El presente trabajo tiene como objetivo analizar la cadena de suministro en un sector de gran importancia en la economía española, como es el metalúrgico. En concreto, buscamos determinar su cadena de suministro, definiendo los principales eslabones que la configuran y las relaciones entre ellos.Abstract: In the current business context, competition is no longer firm against firm, but has moved on to a higher plane, with the generation of supply chain against supply chain competition.  Therefore, Supply Chain Management (SCM has strategic relevance as a source of competitive advantage. The design of the supply chain is defined largely by the characteristics of the sector. Consequently, sectorial analysis is required. The aim of this paper is to analyze the supply chain of the metallurgical sector. Specifically, it will be focused on determining its supply chain and defining its main links and relationships.

  19. Isolation and structure determination of the intact sialylated N-linked carbohydrate chains of recombinant human follitropin expressed in Chinese hamster ovary cells

    NARCIS (Netherlands)

    Vliegenthart, J.F.G.; Hård, K.; Mekking, A.; Damm, J.B.L.; Kamerling, J.P.; Boer, W. de; Wijnands, R.A.

    1990-01-01

    Biologically active recombinant human follitropin has been expressed in Chinese hamster ovary cells. The carbohydrate chains of the recombinant glycoprotein hormone were enzymatically released by peptide-N4-(N-acetyl-beta-glucosaminyl)asparagine amidase F. The oligosaccharides were separated from

  20. Suitability of real-time quantitative polymerase chain reaction and enzyme-linked immunosorbent assay for cry9C detection in Mexican corn tortillas: fate of DNA and protein after alkaline cooking.

    Science.gov (United States)

    Quirasco, Maricarmen; Schoel, Bernd; Plasencia, Javier; Fagan, John; Galvez, Amanda

    2004-01-01

    Alkaline-cooked corn, called nixtamal, is the basis for many traditional corn products such as tortillas, chips, and taco shells that are used widely in Mexico and Central America and in the preparation of snack foods that are consumed globally. To assess the effects of alkaline and thermal treatments on the detectability of DNA and protein for the presence of genetically modified sequences, various nixtamalized products were prepared from blends of conventional white corn containing 0.1, 1.0, and 10% transgenic corn (event CBH 351, StarLink). Real-time quantitative polymerase chain reactions (RTQ-PCR) and immunoassays were used to determine the cry9C gene and protein, respectively, in unprocessed corn kernels, freshly prepared alkaline-cooked and ground corn (masa), masa flour, tortillas prepared from masa by heat treatment, chips prepared from damp masa dough by deep frying, and from tortillas processed at high (200 degrees C) and low temperatures (70 degrees C). In spite of progressive degradation of genomic DNA during processing, RTQ-PCR genetic analysis allowed detection and quantification of the cry9C gene in all products prepared from 10, 1, and 0.1% StarLink corn, except deep-fried chips containing 0.1% StarLink. Enzyme-linked immunosorbent assays readily detected corn (10, 1, and 0.1% StarLink) as well as in nonfried tortilla and masa products. This technique was not suitable for thermally treated nixtamalized products containing transgenic corn.

  1. A simple, high-throughput method to detect Plasmodium falciparum single nucleotide polymorphisms in the dihydrofolate reductase, dihydropteroate synthase, and P. falciparum chloroquine resistance transporter genes using polymerase chain reaction- and enzyme-linked immunosorbent

    DEFF Research Database (Denmark)

    Alifrangis, Michael; Enosse, Sonia; Pearce, Richard

    2005-01-01

    . However, to be a practical tool in the surveillance of drug resistance, simpler methods for high-throughput haplotyping are warranted. Here we describe a quick and simple technique that detects dhfr, dhps, and Pfcrt SNPs using polymerase chain reaction (PCR)- and enzyme-linked immunosorbent assay (ELISA...... the SNPs of dhfr, dhps, and Pfcrt with high specificity. The SSOP-ELISA compared well with a standard PCR-restriction fragment length polymorphism procedure, and gave identical positive results in more than 90% of the P. falciparum slide-positive samples tested. The SSOP-ELISA of all dhfr, dhps, or Pfcrt...

  2. The Service-profit Chain

    DEFF Research Database (Denmark)

    Grønholdt, Lars; Martensen, Anne

    2016-01-01

    This paper examines the links between employee attitudes, customer loyalty and company profitability. From a conceptual point of view, this employee-customer-profit chain, also known as the service-profit chain, is well founded and generally accepted. But for many companies, it seems difficult...... to demonstrate such links, and several issues must be addressed to uncover the links. To investigate these links empirically, a hotel chain provided data matching employee and customer measures with measures of profitability. We have successfully employed a modeling approach, and the paper reports empirical...... evidence of the employee-customer-profit chain. As it is possible to estimate the links, we have demonstrated their effect on company profitability. The research findings provide a better understanding of the service-profit chain and may help practitioners in improving company financial performance....

  3. Multiple shape-memory behavior and thermal-mechanical properties of peroxide cross-linked blends of linear and short-chain branched polyethylenes

    National Research Council Canada - National Science Library

    Kolesov, I. S; Radusch, H.-J

    2008-01-01

    ...% of liquid peroxide 2,5-dimethyl-2,5-di-(tert.butylperoxy)-hexane at 190°C. The average cross-link density estimated by means of the Mooney-Rivlin equation on the basis of tensile test data was characterized between 130 and 170 mol•m...

  4. Cancer immunotherapy using a DNA vaccine encoding a single-chain trimer of MHC class I linked to an HPV-16 E6 immunodominant CTL epitope.

    Science.gov (United States)

    Huang, C-H; Peng, S; He, L; Tsai, Y-C; Boyd, D A K; Hansen, T H; Wu, T-C; Hung, C-F

    2005-08-01

    The potency of DNA vaccines may be affected by the efficiency of intracellular processing and MHC class I presentation of encoded antigens. Since a single-chain trimer (SCT) composed of peptide, beta2-microglobulin (beta2m), and MHC class I heavy chain has been shown to bypass antigen processing and lead to stable presentation of peptides, we investigated the efficacy of a DNA vaccine encoding a SCT composed of an immunodominant CTL epitope of human papillomavirus type 16 (HPV-16) E6 antigen, beta2m, and H-2Kb MHC class I heavy chain (pIRES-E6-beta2m-Kb). Transfection of 293 cells with pIRES-E6-beta2m-Kb can bypass antigen processing and lead to stable presentation of E6 peptide. Furthermore, C57BL/6 mice vaccinated with pIRES-E6-beta2m-Kb exhibited significantly increased E6 peptide-specific CD8+ T-cell immune responses compared to mice vaccinated with DNA encoding wild-type E6. Most importantly, 100% of mice vaccinated with pIRES-E6-beta2m-Kb DNA were protected against a lethal challenge of E6-expressing TC-1 tumor cells. In contrast, all mice vaccinated with wild-type E6 DNA or control plasmid DNA grew tumors. Our data indicate that a DNA vaccine encoding a SCT can lead to stable enhanced MHC class I presentation of encoded antigenic peptide and may be useful for improving DNA vaccine potency to control tumors or infectious diseases.

  5. Circulating N-Linked Glycoprotein Side-Chain Biomarker, Rosuvastatin Therapy, and Incident Cardiovascular Disease: An Analysis From the JUPITER Trial.

    Science.gov (United States)

    Akinkuolie, Akintunde O; Glynn, Robert J; Padmanabhan, Latha; Ridker, Paul M; Mora, Samia

    2016-07-13

    GlycA, a novel protein glycan biomarker of N-acetyl side chains of acute-phase proteins, was recently associated with incident cardiovascular disease (CVD) in healthy women. Whether GlycA predicts CVD events in the setting of statin therapy in men and women without CVD but with evidence of chronic inflammation is unknown. In the Justfication for the Use of Statins in Prevention: an Intervention Trial Evaluating Rosuvastatin (JUPITER) trial (NCT00239681), participants with low-density lipoprotein cholesterol 0.20). In the JUPITER trial, increased levels of GlycA were associated with an increased risk of CVD events independent of traditional risk factors and hsCRP. URL: http://www.clinicaltrials.gov. Unique identifier: NCT00239681. © 2016 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

  6. A Markov chain model for N-linked protein glycosylation--towards a low-parameter tool for model-driven glycoengineering.

    Science.gov (United States)

    Spahn, Philipp N; Hansen, Anders H; Hansen, Henning G; Arnsdorf, Johnny; Kildegaard, Helene F; Lewis, Nathan E

    2016-01-01

    Glycosylation is a critical quality attribute of most recombinant biotherapeutics. Consequently, drug development requires careful control of glycoforms to meet bioactivity and biosafety requirements. However, glycoengineering can be extraordinarily difficult given the complex reaction networks underlying glycosylation and the vast number of different glycans that can be synthesized in a host cell. Computational modeling offers an intriguing option to rationally guide glycoengineering, but the high parametric demands of current modeling approaches pose challenges to their application. Here we present a novel low-parameter approach to describe glycosylation using flux-balance and Markov chain modeling. The model recapitulates the biological complexity of glycosylation, but does not require user-provided kinetic information. We use this method to predict and experimentally validate glycoprofiles on EPO, IgG as well as the endogenous secretome following glycosyltransferase knock-out in different Chinese hamster ovary (CHO) cell lines. Our approach offers a flexible and user-friendly platform that can serve as a basis for powerful computational engineering efforts in mammalian cell factories for biopharmaceutical production. Copyright © 2015 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

  7. Carbohydrate-binding specificities of five lectins that bind to O-Glycosyl-linked carbohydrate chains. Quantitative analysis by frontal-affinity chromatography.

    Science.gov (United States)

    Sueyoshi, S; Tsuji, T; Osawa, T

    1988-07-15

    The carbohydrate-binding specificities of lectins purified from Agaricus bisporus (ABA-I), Arachis hypogaea (PNA), Bauhinia purpurea (BPA), Glycine max (SBA), and Vicia villosa (VVA-B4) have been studied by affinity chromatography on columns of the immobilized lectins, and quantitatively analyzed by frontal affinity chromatography. These five lectins could be classified into two groups with respect to their reactivities with typical mucin-type glycopeptides, beta-D-Galp-(1----3)-alpha-D-GalpNAc-(1----3)-Ser/Thr (2) and alpha-D-GalpNAc-(1----3)-Ser/Thr (3). One group, which consists of ABA-I, PNA, and BPA, preferentially binds to 2, and the other, which consists of SBA and VVA-B4, shows higher affinity for 3 than for 2. Among the lectins tested, only ABA-I was found to bind to a sialylated glycopeptide, whic which was prepared from human erythrocyte glycophorin A and contains three three tetrasaccharide chains having the structure of alpha-NeuAc-(2----3)-beta-D-GAlp-(1----3)-NeuAC-(2----6)]-alpha-D-Galp NAc-(1----, with an association constant of 15 microM, whereas the association constants of the other four lectins for this sialylated glycopeptide were less than 3.5 mM. On the other hand, removal of the beta-D-galactopyranosyl group from a glycopeptide containing sequence 2 resulted in decreased association constants for the three lectins of the first group, especially ABA-I and PNA. The two lectins of the second group showed a high affinity for 3, but SBA preferentially interacted with oligosaccharides containing the alpha-D-GalpNAc-(1----3)-beta-D-Galp-(1----3)-D-GlapNAc sequence, prepared from a blood group A-active oligosaccharide.

  8. Role of haptoglobin on the uptake of native and beta-chain [trimesoyl-(Lys82)beta-(Lys82)beta] cross-linked human hemoglobins in isolated perfused rat livers.

    Science.gov (United States)

    Chow, Edwin C Y; Liu, Lichuan; Ship, Noam; Kluger, Ronald H; Pang, K Sandy

    2008-05-01

    The role of haptoglobin in liver cell entry of acellular native hemoglobin, and cross-linked human hemoglobin, a potentially useful oxygen-carrier alternative in transfusion medicine, was examined in the recirculating, perfused rat liver preparation. Doses of tritiated native human or beta-chain [trimesoyl-(Lys82)beta-(Lys82)beta] cross-linked human hemoglobin were preincubated with haptoglobin-containing rat plasma or Krebs Henseleit bicarbonate buffer for 30 min and used for perfusion. Concentrations (dpm/ml) in reservoir, before and after separation of the hemoglobins and metabolites by gel filtration fast protein liquid chromatography column chromatography, were similar, showing mostly the presence of intact hemoglobin. Each hemoglobin species underwent a rapid distribution phase, followed by a protracted elimination phase. The radioactivity in bile at 3 h consisted of low molecular weight metabolites, and cumulative excretion was slightly higher when rat plasma was present: for native hemoglobin, 7.1 +/- 1.6% versus 9.2 +/- 2.1% dose; for cross-linked hemoglobin, 5.0 +/- 1.7% versus 7.2 +/- 0.8% dose. Data fit to a two-compartment model and physiologically based model revealed a significantly faster influx clearance (CL(influx)) over the metabolic intrinsic clearance (CL(int, met)). The ratios of CL(influx)/CL(int, met) were 125 and 535 for native hemoglobin in the absence and presence of rat haptoglobin, respectively, according to compartmental analyses; the ratios were 25 and 53, respectively, according to physiological modeling. The corresponding ratios for cross-linked hemoglobin in the absence and presence of rat haptoglobin were 55 and 81, respectively, and 24 and 70 for compartmental and physiological modeling. Although haptoglobin enhanced the hepatic internalization of the hemoglobins, the impact on the net clearance was lessened since degradation was the rate-limiting step.

  9. Understanding the supply chain

    Directory of Open Access Journals (Sweden)

    Aćimović Slobodan

    2006-01-01

    Full Text Available Supply chain management represents new business philosophy and includes strategically positioned and much wider scope of activity in comparison with its "older brother" - management of logistics. Philosophy of the concept of supply chain is directed to more coordination of key business functions of every link in distribution chain in the process of organization of the flow of both goods and information, while logistic managing instruments are focused on internal optimum of flows of goods and information within one company. Applying the concept of integrated supply chain among several companies makes the importance of operative logistics activity even greater on the level of one company, thus advancing processes of optimum and coordination within and between different companies and confirms the importance of logistics performances for the company’s profitability. Besides the fact that the borders between companies are being deleted, this concept of supply chain in one distribution channel influences increasing of importance of functional, i.e. traditional business managing approaches but instead it points out the importance of process managing approaches. Although the author is aware that "there is nothing harder, more dangerous and with uncertain success, but to find a way for introducing some novelties (Machiavelli, it would be even his additional stimulation for trying to bring closer the concept and goals of supply chain implementation that are identified in key, relevant, modern, theoretical and consulting approaches in order to achieve better understanding of the subject and faster implementation of the concept of supply chain management by domestic companies.

  10. Heavy Chain Diseases

    Science.gov (United States)

    ... heavy chain produced: Alpha Gamma Mu Alpha Heavy Chain Disease Alpha heavy chain disease (IgA heavy chain ... disease or lead to a remission. Gamma Heavy Chain Disease Gamma heavy chain disease (IgG heavy chain ...

  11. Markov chains

    CERN Document Server

    Revuz, D

    1984-01-01

    This is the revised and augmented edition of a now classic book which is an introduction to sub-Markovian kernels on general measurable spaces and their associated homogeneous Markov chains. The first part, an expository text on the foundations of the subject, is intended for post-graduate students. A study of potential theory, the basic classification of chains according to their asymptotic behaviour and the celebrated Chacon-Ornstein theorem are examined in detail. The second part of the book is at a more advanced level and includes a treatment of random walks on general locally compact abelian groups. Further chapters develop renewal theory, an introduction to Martin boundary and the study of chains recurrent in the Harris sense. Finally, the last chapter deals with the construction of chains starting from a kernel satisfying some kind of maximum principle.

  12. Expression of Leptin and Visfatin in Gingival Tissues of Chronic Periodontitis With and Without Type 2 Diabetes Mellitus: A Study Using Enzyme-Linked Immunosorbent Assay and Real-Time Polymerase Chain Reaction.

    Science.gov (United States)

    Ghallab, Noha A; Amr, Eman M; Shaker, Olfat G

    2015-07-01

    The aim of this study is to investigate the protein and gene expression of leptin and visfatin in gingival tissue from patients with chronic periodontitis (CP), patients with CP and type 2 diabetes mellitus (T2DM), and healthy individuals. The study includes 50 individuals: 10 healthy individuals, 20 patients with CP, and 20 patients with CP and T2DM. Plaque index, gingival index, probing depth, and clinical attachment loss were measured, and gingival biopsies were obtained. Leptin and visfatin protein expression in gingival tissues was determined using enzyme-linked immunosorbent assay, and messenger RNA (mRNA) expression was measured via real-time polymerase chain reaction. The highest leptin mRNA and protein expression was observed in the control group and was significantly (P ≤0.05) different from the CP and CP+T2DM groups. Gingival tissues from patients with CP and T2DM had a significant increase in visfatin and a decrease in leptin gene and protein expression (P <0.05) compared with both controls and patients with CP. Expression of leptin and visfatin in the gingival tissues suggests a possible role for these adipokines in the pathogenesis of CP and T2DM.

  13. Two CpG mutational hot spots in the X-linked interleukin-2 receptor gamma chain gene (IL2RG) may cause 15% of all human severe combined immunodeficiency

    Energy Technology Data Exchange (ETDEWEB)

    Pepper, A.E.; Puck, J.M. [National Center for Human Genome Research, Bethseda, MD (United States); Liu, X. [Univ. of Pennsylvania School of Medicine, Philadelphia, PA (United States)

    1994-09-01

    Severe combined immunodeficiency (SCID), a syndrome of profoundly impaired cellular and humoral immune function, is caused by various autosomal gene defects, including adenosine deaminase (ADA) deficiency, as well as mutations in the X-linked IL2RG gene encoding the gamma chain of the lymphocyte receptor for IL-2. Mutational analysis of IL2RG was performed using genomic DNA from males with SCID referred from genetics and immunology centers. Single strand conformation polymorphisms (SSCP) were sought by PCR amplification of each of the 8 IL2RG exons using labelled flanking primers. Sequence of exons with aberrant SSCP detected a majority of unique deleterious IL2RG mutations in 30 unrelated SCID patients. However, multiple mutations were seen at CpG dinucleotides, known to be C{yields}T transversion sites. cDNA 690-691 in exon 5 was mutated in 4 patients, 1 patient with each of the C{sub 690}{yields}T causing an Arg{yields}Cys substitution, and 1 with G{sub 691}{yields}A causing Arg{yields}His. Two other patients had SCID caused by a single mutation in IL2RG exon 7. This C{sub 879}{yields}T, also in a CpG, changed an Arg to STOP, resulting in loss of the SH2-related intracellular domain. In addition to our patients, 1 patient with each of the C{sub 690} and the C{sub 879} mutations have been reported by others, giving an overall incidence of 20% from our lab and 21% from all reported IL2RG SCID mutations. While ADA defects account for approximately 15% of SCID, a striking male SCID predominance suggest up to 70% of the cases are X-linked, due to IL2RG mutation. Thus, screening for mutations at the 2 CpG hot spots we have found in IL2RG can identify the genotype of as many SCID cases as are found by ADA testing.

  14. Comparison of the university hospital and county hospitals in western Sweden to identify potential weak links in the early chain of care for acute stroke: results of an observational study.

    Science.gov (United States)

    Wireklint Sundström, Birgitta; Herlitz, Johan; Hansson, Per Olof; Brink, Peter

    2015-09-08

    To identify weak links in the early chain of care for acute stroke. 9 emergency hospitals in western Sweden, each with a stroke unit, and the emergency medical services (EMS). All patients hospitalised with a first and a final diagnosis of stroke-between 15 December 2010 and 15 April 2011. The university hospital in the city of Gothenburg was compared with 6 county hospitals. PRIMARY AND SECONDARY MEASURES: (1) The system delay, that is, median delay time from call to the EMS until diagnosis was designated as the primary end point. Secondary end points were: (2) the system delay time from call to the EMS until arrival in a hospital ward, (3) the use of the EMS, (4) priority at the dispatch centre and (5) suspicion of stroke by the EMS nurse. In all, 1376 acute patients with stroke (median age 79 years; 49% women) were included. The median system delay from call to the EMS until (1) diagnosis (CT scan) and (2) arrival in a hospital ward was 3 h and 52 min and 4 h and 22 min, respectively. The system delay (1) was significantly shorter in county hospitals. (3) The study showed that 76% used the EMS (Gothenburg 71%; the county 79%; pStroke was suspected in 65% of cases. A prenotification was sent in 32% (Gothenburg 52%; the county 20%; pStroke was suspected in two-thirds of the cases, but a prenotification was seldom sent to the hospital. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  15. catena-Poly[[[N-(4-amino-1,6-dihydro-1-methyl-5-nitroso-6-oxopyrimidin-2-yl)-(S)-glutamato]hexaaquabarium]-mu-N-(4-amino-1,6-dihydro-1-methyl-5-nitroso-6-oxopyrimidin-2-yl)-(S)-glutamato]: coordination polymer chains linked into a three-dimensional framework by N-H...O and O-H...O hydrogen bonds.

    Science.gov (United States)

    López Garzón, Rafael; López León, M Dolores; Low, John N; Glidewell, Christopher

    2005-05-01

    In the title complex, [Ba(C10H12N5O6)2(H2O)6]n, the Ba atom is nine-coordinated by six water ligands and three carboxylate O atoms. The Ba2+ cations and the anionic glutamate ligands form coordination polymer chains, and these chains are linked by pairs of N-H...O hydrogen bonds and pairs of O-H...O hydrogen bonds to form a continuous three-dimensional framework of cations and anions, which is reinforced by hydrogen bonds involving the water molecules.

  16. A conceptual framework for supply chain governance: An application to agri-food chains in China

    NARCIS (Netherlands)

    Zhang, X.Y.; Aramyan, L.H.

    2009-01-01

    Purpose - Chinese agri-food chains consist of the millions of small scale farmers, who are not well structured and organized in the supply chain. Owing to market liberalization and globalization, one of the most challenging issues along agri-food chains in China is becoming the issue of how to link

  17. Dystrophin deficiency in canine X-linked muscular dystrophy in Japan (CXMDJ alters myosin heavy chain expression profiles in the diaphragm more markedly than in the tibialis cranialis muscle

    Directory of Open Access Journals (Sweden)

    Hijikata Takao

    2008-01-01

    Full Text Available Abstract Background Skeletal muscles are composed of heterogeneous collections of muscle fiber types, the arrangement of which contributes to a variety of functional capabilities in many muscle types. Furthermore, skeletal muscles can adapt individual myofibers under various circumstances, such as disease and exercise, by changing fiber types. This study was performed to examine the influence of dystrophin deficiency on fiber type composition of skeletal muscles in canine X-linked muscular dystrophy in Japan (CXMDJ, a large animal model for Duchenne muscular dystrophy. Methods We used tibialis cranialis (TC muscles and diaphragms of normal dogs and those with CXMDJ at various ages from 1 month to 3 years old. For classification of fiber types, muscle sections were immunostained with antibodies against fast, slow, or developmental myosin heavy chain (MHC, and the number and size of these fibers were analyzed. In addition, MHC isoforms were detected by gel electrophoresis. Results In comparison with TC muscles of CXMDJ, the number of fibers expressing slow MHC increased markedly and the number of fibers expressing fast MHC decreased with growth in the affected diaphragm. In populations of muscle fibers expressing fast and/or slow MHC(s but not developmental MHC of CXMDJ muscles, slow MHC fibers were predominant in number and showed selective enlargement. Especially, in CXMDJ diaphragms, the proportions of slow MHC fibers were significantly larger in populations of myofibers with non-expression of developmental MHC. Analyses of MHC isoforms also indicated a marked increase of type I and decrease of type IIA isoforms in the affected diaphragm at ages over 6 months. In addition, expression of developmental (embryonic and/or neonatal MHC decreased in the CXMDJ diaphragm in adults, in contrast to continuous high-level expression in affected TC muscle. Conclusion The CXMDJ diaphragm showed marked changes in fiber type composition unlike TC muscles

  18. A quantitative analysis of the chain fountain

    Science.gov (United States)

    Pantaleone, J.

    2017-06-01

    When a chain flows up over the edge of a container and then falls to the ground below, it is observed that the top of the chain rises up above the container's edge. This is called a "chain fountain," and is an entertaining and counterintuitive phenomenon. In this paper, the steady-state motion of the fountain is analyzed experimentally and theoretically. Measurements are given for the speeds and heights for three different chains and three different distances from the container to the floor. It is shown that the distance the chain rises above the container is proportional to the force from the container on the chain. A simple model is developed for how the chain interacts with the container, and shows that a link lifts-off from the container after rotating by a relatively small angle. The model's predictions agree very well with the measurements for the two ball-chains.

  19. Kinetic Chain Rehabilitation: A Theoretical Framework

    Directory of Open Access Journals (Sweden)

    Aaron Sciascia

    2012-01-01

    Full Text Available Sequenced physiologic muscle activations in the upper and lower extremity result in an integrated biomechanical task. This sequencing is known as the kinetic chain, and, in upper extremity dominant tasks, the energy development and output follows a proximal to distal sequencing. Impairment of one or more kinetic chain links can create dysfunctional biomechanical output leading to pain and/or injury. When deficits exist in the preceding links, they can negatively affect the shoulder. Rehabilitation of shoulder injuries should involve evaluation for and restoration of all kinetic chain deficits that may hinder kinetic chain function. Rehabilitation programs focused on eliminating kinetic chain deficits, and soreness should follow a proximal to distal rationale where lower extremity impairments are addressed in addition to the upper extremity impairments. A logical progression focusing on flexibility, strength, proprioception, and endurance with kinetic chain influence is recommended.

  20. The link in Linking

    Science.gov (United States)

    Caldwell, Jane C; Chiale, Pablo A; Gonzalez, Mario D; Baranchuk, Adrian

    2013-01-01

    We present 2 cases of the slow-fast form of AVNRT with initially narrow QRS complexes followed by sudden unexpected transition to persistently wide QRS complexes due to aberrant intraventricular conduction. Introduction of a properly timed extrastimulus in one case and critical oscillations in cycle length due to short-long coupling in the second case set the stage for the initial bundle branch block. However, persistence of the aberrancy pattern once the initial event abated was maintained by the "linking" phenomenon. Delayed, retrograde concealed activation from the contralateral bundle branch perpetuated the initial bundle branch block. PMID:23840106

  1. Chain Assembly and Disassembly Processes Differently Affect the Conformational Space of Ubiquitin Chains.

    Science.gov (United States)

    Kniss, Andreas; Schuetz, Denise; Kazemi, Sina; Pluska, Lukas; Spindler, Philipp E; Rogov, Vladimir V; Husnjak, Koraljka; Dikic, Ivan; Güntert, Peter; Sommer, Thomas; Prisner, Thomas F; Dötsch, Volker

    2018-02-06

    Ubiquitination is the most versatile posttranslational modification. The information is encoded by linkage type as well as chain length, which are translated by ubiquitin binding domains into specific signaling events. Chain topology determines the conformational space of a ubiquitin chain and adds an additional regulatory layer to this ubiquitin code. In particular, processes that modify chain length will be affected by chain conformations as they require access to the elongation or cleavage sites. We investigated conformational distributions in the context of chain elongation and disassembly using pulsed electron-electron double resonance spectroscopy in combination with molecular modeling. Analysis of the conformational space of diubiquitin revealed conformational selection or remodeling as mechanisms for chain recognition during elongation or hydrolysis, respectively. Chain elongation to tetraubiquitin increases the sampled conformational space, suggesting that a high intrinsic flexibility of K48-linked chains may contribute to efficient proteasomal degradation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Qualitative methodology for efficient food chain design

    NARCIS (Netherlands)

    Apaiah, R.K.; Hendrix, E.M.T.; Meerdink, G.; Linnemann, A.R.

    2005-01-01

    This paper presents a methodology to efficiently design food supply chains. The goals of quality, cost and environmental load are looked at independently of each other. Food chains are made up of links and are designed to deliver a particular product with consumer-specified attributes. These

  3. Kinematics and Dynamics of Roller Chain Drives

    DEFF Research Database (Denmark)

    Fuglede, Niels

    There are two main subjects of this work: Kinematic and dynamic modeling and analysis of roller chain drives. In the kinematic analysis we contribute first with a complete treatment of the roller chain drive modeled as a four-bar mechanism. This includes a general, exact and approximate analysis...... which is useful for predicting the characteristic loading of the roller chain drive. As a completely novel contribution, a kinematic model and analysis is presented which includes both spans and sprockets in a simple chain drive system. A general procedure for determination of the total wrapping length...... is presented, which also allows for exact sprocket center positions for a chain with a given number of links. Results show that the total chain wrapping length varies periodically with the tooth frequency. These results are of practical importance to both the design, installation and operation of roller chain...

  4. Linked Partitions and Linked Cycles

    OpenAIRE

    Chen, William Y. C.; Wu, Susan Y. J.; Yan, Catherine H.

    2006-01-01

    The notion of noncrossing linked partition arose from the study of certain transforms in free probability theory. It is known that the number of noncrossing linked partitions of [n+1] is equal to the n-th large Schroder number $r_n$, which counts the number of Schroder paths. In this paper we give a bijective proof of this result. Then we introduce the structures of linked partitions and linked cycles. We present various combinatorial properties of noncrossing linked partitions, linked partit...

  5. What Happens When the Supply Chain Breaks? Implications for the Army Supply Chain Under Attack

    National Research Council Canada - National Science Library

    DeBusk, Steven

    2003-01-01

    .... In a system of tightly linked supply chains consisting of consumers, retailers, suppliers, and manufacturers, a sudden change in their ability to communicate data or distribute product can have a...

  6. Scandinavian links

    DEFF Research Database (Denmark)

    Matthiessen, Christian Wichmann; Knowles, Richard D.

    2014-01-01

    The European Round Table of Industrialists identified in the 1980ies 14 missing links in the transportation network of the continent. Three of them were found around the Danish island of Zealand. One link is within the nation, the other two are between nations. One link connects heavy economic....... They concentrate traffic flows and create strong transport corridors. They are the basis of new regional development regimes. “Ferries connect systems, fixed links unite systems”....

  7. Marginal AMP chain graphs

    OpenAIRE

    Pena, Jose M.

    2014-01-01

    We present a new family of models that is based on graphs that may have undirected, directed and bidirected edges. We name these new models marginal AMP (MAMP) chain graphs because each of them is Markov equivalent to some AMP chain graph under marginalization of some of its nodes. However, MAMP chain graphs do not only subsume AMP chain graphs but also multivariate regression chain graphs. We describe global and pairwise Markov properties for MAMP chain graphs and prove their equivalence for...

  8. Integrating Supply Chain and Production Chain: a Genesis in the Ethanol Industry

    Directory of Open Access Journals (Sweden)

    Eder Moreno Ferragi

    2016-06-01

    Full Text Available Although frequently used interchangeably, the concepts of supply chain and production chain are considered in this study as two distinct and complementary theoretical frameworks for the conception of a data-mapping model titled SCMap – Supply Chain Map. The model’s objective is to identify and assess real chains of companies and products. An application in the agribusiness sector, starting with a specific sugarcane processing plant and the biofuel ethanol is performed. The SCMap establishes a structured and integrated manner of linking products and companies, considering three different categories of relationships: (1 between companies – supply chain approach; (2 between products – production chain approach, and; (3 between companies and products – regarding commercial practices in the corporate environment. Grounded on Graph Theory and Social Network Analysis – SNA, the software UCINET and NetDraw application are used to draw the maps and quantitatively assess the centrality of each company and product relative to the whole chain.

  9. Dystrophin deficiency in canine X-linked muscular dystrophy in Japan (CXMDJ) alters myosin heavy chain expression profiles in the diaphragm more markedly than in the tibialis cranialis muscle

    OpenAIRE

    Hijikata Takao; Nakamura Akinori; Yuasa Katsutoshi; Takeda Shinichi

    2008-01-01

    Abstract Background Skeletal muscles are composed of heterogeneous collections of muscle fiber types, the arrangement of which contributes to a variety of functional capabilities in many muscle types. Furthermore, skeletal muscles can adapt individual myofibers under various circumstances, such as disease and exercise, by changing fiber types. This study was performed to examine the influence of dystrophin deficiency on fiber type composition of skeletal muscles in canine X-linked muscular dy...

  10. Logistic chain modelling

    NARCIS (Netherlands)

    Slats, P.A.; Bhola, B.; Evers, J.J.M.; Dijkhuizen, G.

    1995-01-01

    Logistic chain modelling is very important in improving the overall performance of the total logistic chain. Logistic models provide support for a large range of applications, such as analysing bottlenecks, improving customer service, configuring new logistic chains and adapting existing chains to

  11. Health supply chain management.

    Science.gov (United States)

    Zimmerman, Rolf; Gallagher, Pat

    2010-01-01

    This chapter gives an educational overview of: * The actual application of supply chain practice and disciplines required for service delivery improvement within the current health environment. * A rationale for the application of Supply Chain Management (SCM) approaches to the Health sector. * The tools and methods available for supply chain analysis and benchmarking. * Key supply chain success factors.

  12. Chains and identity

    NARCIS (Netherlands)

    Grijpink, J.H.A.M.

    2012-01-01

    This article is available in English and DutchGuidelines are presented to cope with identity problems in chains. A chain is a collaboration of a great number of autonomous organisations and professionals to tackle a dominant chain problem. In many chains identity fraud is an aspect of the dominant

  13. Silicone chain extender

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a silicone chain extender, more particularly a chain extender for silicone polymers and copolymers, to a chain extended silicone polymer or copolymer and to a functionalized chain extended silicone polymer or copolymer, to a method for the preparation thereof...

  14. Effect of chain stiffness on the structure of single-chain polymer nanoparticles

    DEFF Research Database (Denmark)

    Moreno, Angel J; Bacova, Petra; Lo Verso, Federica

    2018-01-01

    of the domains is in all cases similar to that of Gaussian chains or rings, irrespective of the stiffness and degree of cross-linking. It is the spatial arrangement of the domains which determines the global structure of the SCNP (sparse Gaussian-like object or crumpled globule). Since intramolecular stiffness......Polymeric single-chain nanoparticles (SCNPs) are soft nano-objects synthesized by purely intramolecular cross-linking of single polymer chains. By means of computer simulations, we investigate the conformational properties of SCNPs as a function of the bending stiffness of their linear polymer...

  15. Vaccination with an adenoviral vector encoding the tumor antigen directly linked to invariant chain induces potent CD4(+) T-cell-independent CD8(+) T-cell-mediated tumor control

    DEFF Research Database (Denmark)

    Sorensen, Maria R; Holst, Peter J; Pircher, Hanspeter

    2009-01-01

    vaccination with adenovirus expressing GP alone (Ad-GP), or GP and Ii unlinked (Ad-GP+Ii). Ad-Ii-GP- induced tumor control depended on an improved generation of the tumor-associated neoantigen-specific CD8(+) T-cell response and was independent of CD4(+) T cells. IFN-gamma was shown to be a key player during......Antigen-specific immunotherapy is an attractive strategy for cancer control. In the context of antiviral vaccines, adenoviral vectors have emerged as a favorable means for immunization. Therefore, we chose a strategy combining use of these vectors with another successful approach, namely linkage...... of the vaccine antigen to invariant chain (Ii). To evaluate this strategy we used a mouse model, in which an immunodominant epitope (GP33) of the LCMV glycoprotein (GP) represents the tumor-associated neoantigen. Prophylactic vaccination of C57BL/6 mice with a replication-deficient human adenovirus 5 vector...

  16. Operative Links

    DEFF Research Database (Denmark)

    Wistoft, Karen; Højlund, Holger

    2012-01-01

    educational goals, learning content, or value clarification. Health pedagogy is often a matter of retrospective rationalization rather than the starting point of planning. Health and risk behaviour approaches override health educational approaches. Conclusions: Operational links between health education......, health professionalism, and management strategies pose the foremost challenge. Operational links indicates cooperative levels that facilitate a creative and innovative effort across traditional professional boundaries. It is proposed that such links are supported by network structures, shared semantics...

  17. Sustainable Supply Chain Design

    DEFF Research Database (Denmark)

    Bals, Lydia; Tate, Wendy

    A significant conceptual and practical challenge is how to integrate triple bottom line (TBL; including economic, social and environmental) sustainability into global supply chains. Although this integration is necessary to slow down global resource depletion, understanding is limited of how...... to implement TBL goals across the supply chain. In supply chain design, the classic economic perspective still dominates, although the idea of the TBL is more widely disseminated. The purpose of this research is to add to the sustainable supply chain management literature (SSCM) research agenda...... by incorporating the physical chain, and the (information and financial) support chains into supply chain design. This manuscript tackles issues of what the chains are designed for and how they are designed structurally. Four sustainable businesses are used as illustrative case examples of innovative supply chain...

  18. Developing Model for Supply Chain Management - the Case of Croatia

    Directory of Open Access Journals (Sweden)

    E. Jurun

    2004-01-01

    Full Text Available This paper describes a model of supply chain management (SCM. It explains overall supply chain issues, strategic importance of SCM, supply chain strategies and an example of mathematical formulation. A supply chain is a global network of organizations that cooperate to improve the flows of material and information between suppliers and customers at the lowest cost and the highest speed. The objective of a supply chain is customer satisfaction. At the strategic level, a supply chain can be considered as being composed of five activities: buy, make, move, store and sell. Each activity is a module. The set of modules, along with its links, constitutes a model of the supply chain. Our paper presents some insights into the supply chain strategies of companies in Croatia. The major goal of this paper is to show a model for supply chain management in mathematical terms, with an example of mathematical formulation.

  19. The composite supply chain efficiency model: A case study of the Sishen-Saldanha supply chain

    Directory of Open Access Journals (Sweden)

    Leila L. Goedhals-Gerber

    2016-01-01

    Full Text Available As South Africa strives to be a major force in global markets, it is essential that South African supply chains achieve and maintain a competitive advantage. One approach to achieving this is to ensure that South African supply chains maximise their levels of efficiency. Consequently, the efficiency levels of South Africa’s supply chains must be evaluated. The objective of this article is to propose a model that can assist South African industries in becoming internationally competitive by providing them with a tool for evaluating their levels of efficiency both as individual firms and as a component in an overall supply chain. The Composite Supply Chain Efficiency Model (CSCEM was developed to measure supply chain efficiency across supply chains using variables identified as problem areas experienced by South African supply chains. The CSCEM is tested in this article using the Sishen-Saldanda iron ore supply chain as a case study. The results indicate that all three links or nodes along the Sishen-Saldanha iron ore supply chain performed well. The average efficiency of the rail leg was 97.34%, while the average efficiency of the mine and the port were 97% and 95.44%, respectively. The results also show that the CSCEM can be used by South African firms to measure their levels of supply chain efficiency. This article concludes with the benefits of the CSCEM.

  20. Environmental management the supply chain perspective

    CERN Document Server

    Wong, Christina W Y; Lun, Y H Venus; Cheng, T C E

    2015-01-01

    In view of the increasing quest for environmental management in businesses, this book provides a good reference to firms to understand how they may manage their supply chains to improve business and environmental performance. The book consists of six chapters covering such topics as environmental management, environmental management practices with supply chain efforts, collaborative environmental management, organizational capabilities in environmental management, environmental disclosure, and closed-loop supply chains. The book presents theory-driven discussions on the link between environmental management and business performance in the context of supply chain management. The book will be useful for firms to learn from the research findings and real-life cases to develop plans to implement environmental management practices jointly with supply chain partners.

  1. Sustainability of Global and Local Food Value Chains: An Empirical Comparison of Peruvian and Belgian Asparagus

    OpenAIRE

    Schwarz, Jana; Schuster, Monica; Annaert, Bernd; Maertens, Miet; Mathijs, Erik

    2016-01-01

    The sustainability of food value chains is an increasing concern for consumers, food companies and policy-makers. Global food chains are often perceived to be less sustainable than local food chains. Yet, thorough food chain analyses and comparisons of different food chains across sustainability dimensions are rare. In this article we analyze the local Belgian and global Peruvian asparagus value chains and explore their sustainability performance. A range of indicators linked to environmental...

  2. A heterodimer of a VHH (variable domains of camelid heavy chain-only) antibody that inhibits anthrax toxin cell binding linked to a VHH antibody that blocks oligomer formation is highly protective in an anthrax spore challenge model.

    Science.gov (United States)

    Moayeri, Mahtab; Leysath, Clinton E; Tremblay, Jacqueline M; Vrentas, Catherine; Crown, Devorah; Leppla, Stephen H; Shoemaker, Charles B

    2015-03-06

    Anthrax disease is caused by a toxin consisting of protective antigen (PA), lethal factor, and edema factor. Antibodies against PA have been shown to be protective against the disease. Variable domains of camelid heavy chain-only antibodies (VHHs) with affinity for PA were obtained from immunized alpacas and screened for anthrax neutralizing activity in macrophage toxicity assays. Two classes of neutralizing VHHs were identified recognizing distinct, non-overlapping epitopes. One class recognizes domain 4 of PA at a well characterized neutralizing site through which PA binds to its cellular receptor. A second neutralizing VHH (JKH-C7) recognizes a novel epitope. This antibody inhibits conversion of the PA oligomer from "pre-pore" to its SDS and heat-resistant "pore" conformation while not preventing cleavage of full-length 83-kDa PA (PA83) by cell surface proteases to its oligomer-competent 63-kDa form (PA63). The antibody prevents endocytosis of the cell surface-generated PA63 subunit but not preformed PA63 oligomers formed in solution. JKH-C7 and the receptor-blocking VHH class (JIK-B8) were expressed as a heterodimeric VHH-based neutralizing agent (VNA2-PA). This VNA displayed improved neutralizing potency in cell assays and protected mice from anthrax toxin challenge with much better efficacy than the separate component VHHs. The VNA protected virtually all mice when separately administered at a 1:1 ratio to toxin and protected mice against Bacillus anthracis spore infection. Thus, our studies show the potential of VNAs as anthrax therapeutics. Due to their simple and stable nature, VNAs should be amenable to genetic delivery or administration via respiratory routes. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

  3. Linked data

    NARCIS (Netherlands)

    Koster, L.

    2011-01-01

    Semantisch web, linked data, web 3.0… Het zijn allemaal termen die vaak door elkaar worden gebruikt. Onterecht vindt Lukas Koster van de Universiteit van Amsterdam. Wat houden die begrippen nu eigenlijk in?

  4. Link Analysis

    Science.gov (United States)

    Donoho, Steve

    Link analysis is a collection of techniques that operate on data that can be represented as nodes and links. This chapter surveys a variety of techniques including subgraph matching, finding cliques and K-plexes, maximizing spread of influence, visualization, finding hubs and authorities, and combining with traditional techniques (classification, clustering, etc). It also surveys applications including social network analysis, viral marketing, Internet search, fraud detection, and crime prevention.

  5. The Global Value Chain

    DEFF Research Database (Denmark)

    Sørensen, Olav Jull

    The conference paper aims to develop the global value chain concept by including corporate internal value adding activities and competition to the basic framework in order to turn the global value chain into a strategic management tool......The conference paper aims to develop the global value chain concept by including corporate internal value adding activities and competition to the basic framework in order to turn the global value chain into a strategic management tool...

  6. Risk assessment and management logistics chains

    Directory of Open Access Journals (Sweden)

    Vladimir Vikulov

    2014-03-01

    Full Text Available Background: In the context of economic globalization and increasing complexity of economic relations enterprises need methods and techniques to improve and sustain their position on the global market. Integration processes offer business new opportunities, but at the same time present new challenges for the management, including the key objectives of the risk management. Method: On the basis of analysis tools known from the pertinent literature (Supply Chain Management and Supply Chain Risk Management methods, methods of probability theory, methods of risk management, methods of statistics the authors of this paper proposed their own risk assessment method and the method of management of logistics chains. The proposed tool is a specific hybrid of solutions known from the literature. Results: The presented method has been successfully used within the frames of economic-mathematical model of industrial enterprises. Indicators of supply chain risks, including risks caused by supplier are considered in this paper. Authors formed a method of optimizing the level of supply chain risk in the integration with suppliers and customers. Conclusion: Every organization, which starting the process of integration with supplier and customers, needs to use tools, methodologies and techniques for identification of "weak links" in the supply chain. The proposed method allows to fix risk origin places in various links of the supply chain and to identify "weak links" of a logistic chain that may occur in the future. The method is a useful tool for managing not only risks and risk situations, but also to improve the efficiency of current assets management by providing the ability to optimize the level of risk in the current assets management of the industrial enterprise.

  7. Drying of willow biomass in supply chains

    NARCIS (Netherlands)

    Gigler, J.

    2000-01-01

    The drying process of willow ( Salix viminalis ) in biomass supply chains to energy plants is quantitatively described. Drying at particle level was modelled for chips and stems by a diffusion equation linked to the mass transfer of moisture to the air. Drying at bulk

  8. Immunoassay and polymerase chain reaction techniques for ...

    African Journals Online (AJOL)

    Objectives: To compare the Reverse Passive Latex Agglutination (RPLA) and Enzyme Linked Immunosorbent Assay (ELISA) techniques with a Polymerase Chain Reaction (PCR) for detection of enterotoxigenic Bacillus cereus. Design: A cross-sectional study. Setting: The Department of Public Health, Pharmacology and ...

  9. New technology and the chain of safety.

    Science.gov (United States)

    Martell, Rob; Macartney, Jason T; Portnik, Danielle

    2017-01-01

    Healthcare is currently experiencing an exponential growth in medical technology but it has not kept pace with similar industries such as the airline industry. New technology has the potential to improve patient safety, but if the introduction of new technology into the healthcare setting is not coordinated in a thoughtful, proactive manner, there may be weak links in the chain of safety that may expose risks for patients. We describe three concepts that represent this chain of safety. We suggest that these are shared among all leadership and frontline staff and that these concepts require their full attention and investment in order to keep the chain of safety intact and avoid a single weak link in implementing new technology.

  10. Using Civilian Supply Chain Management Best Practices to Improve Army Supply Chain Management Procedures

    Science.gov (United States)

    2017-06-09

    innovations. This enterprise resource planning program is the future management program that is expected to increase logistic proficiency across all... enterprise resource planning program system to manage the overall functionality of a supply chain.8 Corporations link organizational strategies to these...increase of 20 percent in less than two years. The case study, “ Managing New Product Development and Supply Chain Risks : The Boeing 787 Case

  11. Pendant triazole ring assisted mesogen containing side chain liquid ...

    Indian Academy of Sciences (India)

    yl containing side- chain liquid-crystalline polymethacrylates were synthesized by free radical polymerization technique. Mesogen was linked to backbone through various spacer units. Monomers and polymers were characterized by FT-IR, 1H ...

  12. Social network analysis and supply chain management

    Directory of Open Access Journals (Sweden)

    Raúl Rodríguez Rodríguez

    2016-01-01

    Full Text Available This paper deals with social network analysis and how it could be integrated within supply chain management from a decision-making point of view. Even though the benefits of using social analysis have are widely accepted at both academic and industry/services context, there is still a lack of solid frameworks that allow decision-makers to connect the usage and obtained results of social network analysis – mainly both information and knowledge flows and derived results- with supply chain management objectives and goals. This paper gives an overview of social network analysis, the main social network analysis metrics, supply chain performance and, finally, it identifies how future frameworks could close the gap and link the results of social network analysis with the supply chain management decision-making processes.

  13. Supply Chain Management og Supply Chain costing

    DEFF Research Database (Denmark)

    Nielsen, Steen; Mortensen, Ole

    2002-01-01

    Formålet med denne artikel er at belyse de muligheder som ligger i at integrere virksomhedens økonomiske styring med begrebet Supply Chain Management (SCM). Dette søges belyst ved først at beskrive den teoretiske ramme, hvori SCM indgår. Herefter analyseres begrebet Supply Chain Costing (SCC) som...... Århus. Et resultat er, at via begrebet Supply Chain Costing skabes der mulighed for at måle logistikkædens aktiviteter i kr./øre. Anvendelsen af denne information har også strategisk betydning for at kunne vælge kunde og leverandør. Ved hjælp af integrationen skabes der også helt nye mulighed...

  14. Editorial: Supply Chain Management

    Directory of Open Access Journals (Sweden)

    Dimitrios Aidonis

    2017-05-01

    Full Text Available This special issue has followed up the 3rd Olympus International Conference on Supply Chains held on Athens Metropolitan Expo, November 7 & 8 2015, Greece. The Conference was organized by the Department of Logistics Technological Educational Institute of Central Macedonia, in collaboration with the: a Laboratory of Quantitative Analysis, Logistics and Supply Chain Management of the Department of Mechanical Engineering, Aristotle University of Thessaloniki (AUTH, b Greek Association of Supply Chain Management (EEL of Northern Greece and the c Supply Chain & Logistics Journal. During the 2-Days Conference more than 60 research papers were presented covering the following thematic areas: (i Transportation, (ii Best Practices in Logistics, (iii Information and Communication Technologies in Supply Chain Management, (iv Food Logistics, (v New Trends in Business Logistics, and (vi Green Supply Chain Management. Three keynote invited speakers addressed interesting issues for the Operational Research, the Opportunities and Prospects of Greek Ports chaired Round Tables with other Greek and Foreign Scientists and Specialists.

  15. Understanding the Chain Fountain

    CERN Document Server

    Biggins, John Simeon

    2013-01-01

    If a chain is initially at rest in a beaker at a height h1 above the ground, and the end of the chain is pulled over the rim of the beaker and down towards the ground and then released, the chain will spontaneously "flow" out of the beaker under gravity. Furthermore, if h1 is sufficient, the beads do not simply drag over the edge of the beaker but form a fountain reaching a height h2 above it. We show that the formation of a fountain requires that the beads come into motion not only by being pulled upwards by the part of the chain immediately above the pile, but also by being pushed upwards by an anomalous reaction force from the pile of stationary chain. We propose possible origins for this force, argue that its magnitude will be proportional to the square of the chain velocity, and predict and verify experimentally that h2 is proportional to h1.

  16. Supply chain management for small business--how to avoid being part of the food chain.

    Science.gov (United States)

    Knechtges, J P; Watts, C A

    2000-08-01

    A supply chain is a series of customer and supplier relationships that extend throughout and beyond the company. It is an interwoven set of links that together form a chain supplying our customers in a seamless and integrated fashion delivering a high level of customer satisfaction. Supply chain management (SCM) integrates all activities so they are focused on customer satisfaction (both internally and externally). One of the things this article will attempt to accomplish is to provide a clear understanding of SCM's positive impact on customer service as well as on improving profitability, cash flow, product cycle times, and communication. Whether we go forward in the supply chain to the final end-user or backward in the supply chain to our supplier's suppliers, SCM will significantly improve our ability to serve our customers.

  17. Supply chain components

    Directory of Open Access Journals (Sweden)

    Vieraşu, T.

    2011-01-01

    Full Text Available In this article I will go through three main logistics components, which are represented by: transportation, inventory and facilities, and the three secondary logistical components: information, production location, price and how they determine performance of any supply chain. I will discuss then how these components are used in the design, planning and operation of a supply chain. I will also talk about some obstacles a supply chain manager may encounter.

  18. Growth and Shape of a Chain Fountain

    CERN Document Server

    Biggins, John S

    2014-01-01

    If a long chain is held in a pot elevated a distance h_1 above the floor, and the end of the chain is then dragged over the rim of the pot and released, the chain flows under gravity down into a pile on the floor. Not only does the chain flow out of the pot, it also leaps above the pot in a "chain-fountain". I predict and observe that if the pot is held at an angle to the vertical the steady state shape of the fountain is an inverted catenary, and discuss how to apply boundary conditions to this solution. In the case of a level pot, the fountain shape is completely vertical. In this case I predict and observe both how fast the fountain grows to its steady state hight, and how it grows quadratically in time if there is no floor. The fountain is driven by an anomalous push force from the pot that acts on the link of chain about to come into motion. I confirm this by designing two new chains, one consisting of hollow cylinders threaded on a string and one consisting of heavy beads separated by long flexible thre...

  19. Supply chain oriented performance measurement for automotive spare parts

    NARCIS (Netherlands)

    de Leeuw, S.L.J.M.; Beekman, L.

    2008-01-01

    Literature provides a number of conceptual frameworks and discussions on performance measurement in supply chains. However, most of these frameworks focus on a single link of a supply chain. Furthermore, there is a lack of empirical analysis and case studies on performance metrics and measurements

  20. Application of Static Synchronous Compensator (STATCOM) in ...

    African Journals Online (AJOL)

    Slow response of the conventional traditional methods for improving power system performance creates the need for adoption of advanced control technologies such as Flexible Alternating Current Transmission System (FACTS) with fast response and low cost for stabilizing electricity grid power and voltage. In this work, we ...

  1. Performance Based Logistics - A Bridge Between Acquisition Reform and Logistics Supply Chain Management

    National Research Council Canada - National Science Library

    Hurst, Dana

    2006-01-01

    .... Performance based logistics links acquisition and supply chain management in the Total Life Cycle Systems Management and thus may provide the opportunity for true reform resulting in increased...

  2. The Relationship between Supply Chain Fit and Return on Assets of the Firm

    OpenAIRE

    Khan, Muhammad Hamza; Khan, Muhammad Hassan; Maqsood, Muhammad Nawaz; Rehman, Khaliq Ur

    2012-01-01

    The decisive point of financial encroachment of supply chain management has been an ongoing interest. Forming on the operations strategy literature, this study examines the links between the supply chain fit (i.e. strategic consistency between the product ‘supply and demand uncertainty and emphasizing on supply chain Structure/design) and financial performance of the firm. We define firms with supply chain fit as firms where the products’ supply and demand uncertainty and supply chain respons...

  3. Failures of chain systems

    CSIR Research Space (South Africa)

    James, A

    1997-03-01

    Full Text Available Chains are used for various purposes in a wide range of industries. This paper describes three case studies where a failure analysis was carried out on chains used in markedly different applications namely: a furnace health, a drilling rig for rock...

  4. Value Chain Engineering

    DEFF Research Database (Denmark)

    Wæhrens, Brian Vejrum; Slepniov, Dmitrij

    2015-01-01

    This workbook is recommended for the attention of students of and managers in Danish small and medium sized enterprises (SMEs). Danish SMEs are currently facing a number of key challenges related to their position in global value chains. This book provides an insight into value chain management...

  5. Shared Value Chain Design

    DEFF Research Database (Denmark)

    Bals, Lydia; Tate, Wendy L.

    In Sustainable Supply Chain Management (SSCM) research still the classic economic perspective is the dominating perspective, although the triple bottom line (including economic, social and ecological) is well accepted. The theoretical foundation for the paper is Stakeholder Theory. Case studies...... in local communities, fundamentally changing supply chains....

  6. Supply Chain Management

    DEFF Research Database (Denmark)

    Wieland, Andreas; Handfield, Robert B.

    Supply chain management has made great strides in becoming a discipline with a standalone body of theories. As part of this evolution, researchers have sought to embed and integrate observed supply chain management phenomena into theoretical statements. In our review, we explore where we have been...

  7. REVERSE SUPPLY CHAIN

    Directory of Open Access Journals (Sweden)

    Tomasz DOMAGAŁA

    2013-10-01

    Full Text Available The paper focuses on the presentation of the reverse supply chain, of which the role in the modern business grows along with the increasing number of environmental regulations and possibilities of reducing an operating cost. The paper also describes main problems in developing the profitable chain and possibilities to take an action in order to overcome them.

  8. Dancing links

    OpenAIRE

    Knuth, Donald E.

    2000-01-01

    The author presents two tricks to accelerate depth-first search algorithms for a class of combinatorial puzzle problems, such as tiling a tray by a fixed set of polyominoes. The first trick is to implement each assumption of the search with reversible local operations on doubly linked lists. By this trick, every step of the search affects the data incrementally. The second trick is to add a ghost square that represents the identity of each polyomino. Thus puts the rule that each polyomino be ...

  9. Environmental footprints in the meat chain

    Science.gov (United States)

    Đekić, I.; Tomašević, I.

    2017-09-01

    The objective of this paper was to present environmental performance of the meat chain and highlight main environmental footprints. The meat sector is recognized as one of the leading polluting sectors in the food industry. The meat chain was analyzed from a five-link perspective introducing the following actors: farm(er)s, slaughterhouses, meat processors, customers and consumers. Meat production needs natural resources (water and energy) resulting in waste and waste water discharge. As an outcome it has a high influence on climate change in respect to global warming, acidification and eutrophication potentials and ozone depletion substances.

  10. Weak chain link breakdown phenomena of multigrade insulation materials

    Energy Technology Data Exchange (ETDEWEB)

    Gallagher, J.; McClung, L.B.

    1982-07-01

    Several failures of multigrade insulation systems have been experienced in metal clad, metal enclosed switchgear, and miniature isolated phase busduct systems. The failure sequence of the series insulation system appeared to originate from a point farthest away from the ground plane and not from the insulation in contact with the ground plane. However, in actuality, the ground plane was periodically elevated in relationship to the insulated busbar due to the presence of moisture created by load and ambient temperature cycling and adverse weather conditions. The insulation material in contact with the ground plane, being a high quality track resistant material, did not exhibit permanent deterioration. However the weakest insulation material degraded with time, weakening the overall insulation path to a point that an elevated ground plane condition resulted in failures of the series insulation system. The phenomena experienced in a specific application and the alternatives considered to correct the situation are described.

  11. Life Studies: Learning beyond the Chain-Link Fence.

    Science.gov (United States)

    Caudell, Lee Sherman

    1996-01-01

    Applied learning projects at George Middle School (Portland, Oregon) include landscaping the school courtyard, helping scientists study pollution in the Columbia Slough, inventorying wildlife around Portland lakes, studying urban ecosystems and sharing information in Spanish with Mexican schools, and planting trees. Describes other school…

  12. Project Decision Chain

    DEFF Research Database (Denmark)

    Rolstadås, Asbjørn; Pinto, Jeffrey K.; Falster, Peter

    2015-01-01

    To add value to project performance and help obtain project success, a new framework for decision making in projects is defined. It introduces the project decision chain inspired by the supply chain thinking in the manufacturing sector and uses three types of decisions: authorization, selection......, and plan decision. A primitive decision element is defined where all the three decision types can be accommodated. Each task in the primitive element can in itself contain subtasks that in turn will comprise new primitive elements. The primitive elements are nested together in a project decision chain....

  13. Global Value Chain Configuration

    DEFF Research Database (Denmark)

    Hernandez, Virginia; Pedersen, Torben

    2017-01-01

    This paper reviews the literature on global value chain configuration, providing an overview of this topic. Specifically, we review the literature focusing on the concept of the global value chain and its activities, the decisions involved in its configuration, such as location, the governance...... modes chosen and the different ways of coordinating them. We also examine the outcomes of a global value chain configuration in terms of performance and upgrading. Our aim is to review the state of the art of these issues, identify research gaps and suggest new lines for future research that would...

  14. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example......, plastics from WEEE is chosen as a Nordic case study. The project aims to propose a number of improvements for this value chain together with representatives from Nordic stakeholders. Based on the experiences made, a guide for other plastic value chains shall be developed....

  15. Moldova - Value Chain Training

    Data.gov (United States)

    Millennium Challenge Corporation — The evaluation of the GHS value chain training subactivity wwas designed to measure the extent, if any, to which the training activities improved the productivity...

  16. Editorial: Supply Chain Management

    Directory of Open Access Journals (Sweden)

    Aidonis, D.

    2012-01-01

    Full Text Available This special issue has followed up the 2nd Olympus International Conference on Supply Chains held on October 5-6, 2012, in Katerini, Greece. The Conference was organized by the Department of Logistics of Alexander Technological Educational Institution (ATEI of Thessaloniki, in collaboration with the Laboratory of Quantitative Analysis, Logistics and Supply Chain Management of the Department of Mechanical Engineering, Aristotle University of Thessaloniki (AUTH. During the 2-Days Conference more than 50 research papers were presented covering the following thematic areas: (i Business Logistics, (ii Transportation, Telematics and Distribution Networks, (iii Green Logistics, (iv Information and Communication Technologies in Supply Chain Management, and (v Services and Quality. Three keynote invited speakers addressed interesting issues for the Humanitarian Logistics, Green Supply Chains of the Agrifood Sector and the Opportunities and Prospects of Greek Ports chaired Round Tables with other Greek and Foreign Scientists and Specialists.

  17. Characterizing Oregon's supply chains.

    Science.gov (United States)

    2013-03-01

    In many regions throughout the world, freight models are used to aid infrastructure investment and : policy decisions. Since freight is such an integral part of efficient supply chains, more realistic : transportation models can be of greater assista...

  18. Writing on polymer chains.

    Science.gov (United States)

    Lutz, Jean-François

    2013-11-19

    Synthetic polymer materials are currently limited by their inability to store information in their chains, unlike some well-characterized biopolymers. Nucleic acids store and transmit genetic information, and amino acids encode the complex tridimensional structures and functions within proteins. To confer similar properties on synthetic materials, researchers must develop"writing" mechanisms, facile chemical pathways that allow control over the primary structure of synthetic polymer chains. The most obvious way to control the primary structure is to connect monomer units one-by-one in a given order using iterative chemistry. Although such synthesis strategies are commonly used to produce peptides and nucleic acids, they produce limited yields and are much slower than natural polymerization mechanisms. An alternative strategy would be to use multiblock copolymers with blocks that have specified sequences. In this case, however, the basic storage element is not a single molecular unit, but a longer block composed of several repeating units. However, the synthesis of multiblock copolymers is long and tedious. Therefore, researchers will need to develop other strategies for writing information onto polymer chains. In this Account, I describe our recent progress in the development of sequence controlled polymerization methods. Although our research focuses on different strategies, we have emphasized sequence-regulation in chain-growth polymerization processes. Chain-growth polymerizations, particularly radical polymerization, are very convenient methods for synthesizing polymers. However, in most cases, such approaches do not lead to controlled monomer sequences. During the last five years, we have shown that controlled/living chain-growth polymerization mechanisms offer interesting advantages for sequence regulation. In such mechanisms, the chains form gradually over time, and therefore the primary structure can be tuned by using time-controlled monomer additions. For

  19. Sustainable and Resilient Supply Chain Network Design under Disruption Risks

    Directory of Open Access Journals (Sweden)

    Sonia Irshad Mari

    2014-09-01

    Full Text Available Sustainable supply chain network design is a rich area for academic research that is still in its infancy and has potential to affect supply chain performance. Increasing regulations for carbon and waste management are forcing firms to consider their supply chains from ecological and social objectives, but in reality, however, facilities and the links connecting them are disrupted from time to time, due to poor weather, natural or manmade disasters or a combination of any other factors. Supply chain systems drop their sustainability objectives while coping with these unexpected disruptions. Hence, the new challenges for supply chain managers are to design an efficient and effective supply chain network that will be resilient enough to bounce back from any disruption and that also should have sufficient vigilance to offer same sustainability under a disruption state. This paper focuses on ecological sustainability, because an environmental focus in a supply chain system is more important and also links with other pillars of sustainability, as the products need to be produced, packed and transported in an ethical way, which should not harm social balance and the environment. Owing to importance of the considered issue, this paper attempts to introduce a network optimization model for a sustainable and resilient supply chain network by incorporating (1 sustainability via carbon emissions and embodied carbon footprints and (2 resilience by incorporating location-specific risks. The proposed goal programming (GP model optimizes the total cost, while considering the resilience and sustainability of the supply chain network.

  20. MASTERING SUPPLY CHAIN RISKS

    Directory of Open Access Journals (Sweden)

    Borut Jereb

    2012-11-01

    Full Text Available Risks in supply chains represent one of the major business issues today. Since every organizationstrives for success and uninterrupted operations, efficient supply chain risk management is crucial.During supply chain risk research at the Faculty of Logistics in Maribor (Slovenia some keyissues in the field were identified, the major being the lack of instruments which can make riskmanagement in an organization easier and more efficient. Consequently, a model which captures anddescribes risks in an organization and its supply chain was developed. It is in accordance with thegeneral risk management and supply chain security standards, the ISO 31000 and ISO 28000families. It also incorporates recent finding from the risk management field, especially from theviewpoint of segmenting of the public.The model described in this paper focuses on the risks itself by defining them by different keydimensions, so that risk management is simplified and can be undertaken in every supply chain andorganizations within them. Based on our mode and consequent practical research in actualorganizations, a freely accessible risk catalog has been assembled and published online from the risksthat have been identified so far. This catalog can serve as a checklist and a starting point in supplychain risk management in organizations. It also incorporates experts from the field into a community,in order to assemble an ever growing list of possible risks and to provide insight into the model andits value in practice.

  1. COMPETITIVE ADVANTAGES IN A NANOTECHNOLOGY VALUE CHAIN

    Directory of Open Access Journals (Sweden)

    Adriana Radan UNGUREANU

    2015-04-01

    Full Text Available The value chain analysis is one of the most important methods for understanding the industrial world. The main task of the value chain that links producers and buyers consists in understanding where or how exactly the value added is generated. In the case of products incorporating nanotechnology, most of them are still in the trial phase into laboratories, but there are some examples of good practices where nanoproducts discovered their way to the market. This paper tries to present two cases of value chains for nanotechnologies applied to textiles by identifying the competitive advantages and focusing on getting some answers for a better understanding of the entire process from production to the final user.

  2. Innovation Across the Supply Chain

    DEFF Research Database (Denmark)

    Druehl, Cheryl; Carrillo, Janice; Hsuan, Juliana

    Innovation is an integral part of every firm’s ongoing operations. Beyond product innovation, supply chain innovations offer a unique source of competitive advantage. We synthesize recent research on innovation in the supply chain, specifically, innovative supply chain processes...

  3. Locations of Racism in Education: A Speech Act Analysis of a Policy Chain

    Science.gov (United States)

    Arneback, Emma; Quennerstedt, Ann

    2016-01-01

    This article explores how racism is located in an educational policy chain and identifies how its interpretation changes throughout the chain. A basic assumption is that the policy formation process can be seen as a chain in which international, national and local policies are "links"--separate entities yet joined. With Sweden as the…

  4. 77 FR 17001 - USDA Public Stakeholder Meeting: Match Making in the Biofuels Value Chain

    Science.gov (United States)

    2012-03-23

    ... USDA Public Stakeholder Meeting: Match Making in the Biofuels Value Chain AGENCY: Office of the Chief... understanding of the biofuels supply chain links between all those involved in feedstock production and the... a short profile of each section of the supply chain and representatives from the participating...

  5. Drying of willow biomass in supply chains

    OpenAIRE

    Gigler, J.

    2000-01-01

    The drying process of willow ( Salix viminalis ) in biomass supply chains to energy plants is quantitatively described. Drying at particle level was modelled for chips and stems by a diffusion equation linked to the mass transfer of moisture to the air. Drying at bulk level is described by a deep bed model, which accounted for the moisture and temperature gradients of wood and air therein. Experimental validation showed that the deep bed model adequately describe...

  6. Sustainability of Global and Local Food Value Chains: An Empirical Comparison of Peruvian and Belgian Asparagus

    Directory of Open Access Journals (Sweden)

    Jana Schwarz

    2016-04-01

    Full Text Available The sustainability of food value chains is an increasing concern for consumers, food companies and policy-makers. Global food chains are often perceived to be less sustainable than local food chains. Yet, thorough food chain analyses and comparisons of different food chains across sustainability dimensions are rare. In this article we analyze the local Belgian and global Peruvian asparagus value chains and explore their sustainability performance. A range of indicators linked to environmental, economic and social impacts is calculated to analyze the contribution of the supply chains to economic development, resource use, labor relations, distribution of added value and governance issues. Our findings suggest that none of the two supply chains performs invariably better and that there are trade-offs among and between sustainability dimensions. Whereas the global chain uses water and other inputs more intensively and generates more employment per unit of land and higher yields, the local chain generates more revenue per unit of land.

  7. Characterizing chain-compact and chain-finite topological semilattices

    OpenAIRE

    Banakh, Taras; Bardyla, Serhii

    2017-01-01

    In the paper we present various characterizations of chain-compact and chain-finite topological semilattices. A topological semilattice $X$ is called chain-compact (resp. chain-finite) if each closed chain in $X$ is compact (finite). In particular, we prove that a (Hausdorff) $T_1$-topological semilattice $X$ is chain-finite (chain-compact) if and only if for any closed subsemilattice $Z\\subset X$ and any continuous homomorphism $h:X\\to Y$ to a (Hausdorff) $T_1$-topological semilattice $Y$ th...

  8. METRODOS: Meteorological preprocessor chain

    DEFF Research Database (Denmark)

    Astrup, P.; Mikkelsen, T.; Deme, S.

    2001-01-01

    The METRODOS meteorological preprocessor chain combines measured tower data and coarse grid numerical weather prediction (NWP) data with local scale flow models and similarity scaling to give high resolution approximations of the meteorological situation. Based on available wind velocity and dire......The METRODOS meteorological preprocessor chain combines measured tower data and coarse grid numerical weather prediction (NWP) data with local scale flow models and similarity scaling to give high resolution approximations of the meteorological situation. Based on available wind velocity...... - heat flux related measurement, e.g. a temperature gradient, are used to give local values of friction velocity and Monin-Obukhov length plus an estimate of the mixing height. The METRODOS meteorological preprocessor chain is an integral part of the RODOS - Real Time On Line Decision Support - program...

  9. Environmental Retail Supply Chains

    DEFF Research Database (Denmark)

    Kotzab, Herbert; Munch, Hilde; de Faultrier, Birgitte

    2011-01-01

    Purpose – The purpose of this paper is to develop a scale that evaluates the environmental elements in retail supply chains and to examine the environmental supply chain management initiatives of the world's largest 100 retailing companies. Design/methodology/approach – The empirical evaluation has...... been undertaken through an investigative approach applying a web-scan framework which included the analysis of web sites and publicly published documents such as annual reports and corporate social responsibility reports. Findings – The authors identified 34 environmental sustainability initiatives...... which were grouped into eight categories; they refer to “fundamental environmental attitude”, “use of energy”, “use of input material”, “product”, “packaging”, “transport”, “consumption” and “waste”. The level of environmental supply chain management can be characterised as very operational and very...

  10. Supply chain quality management

    Directory of Open Access Journals (Sweden)

    Hannan Amoozad Mahdiraji

    2012-10-01

    Full Text Available In recent years, there are several methods introduced for the improvement of operational performances. Total quality management and supply chain management are two methods recommended for this purpose. These two approaches have been studied in most researches separately, while they have objectives in common, and this makes them a strategic means, which can be used, simultaneously. Total quality management and supply chain management play significant roles to increase the organizational competitiveness power. Moreover, they have only one purpose that is customer satisfaction, and they are different only on their approaches to reach their objectives. In this research, we aim to study both approaches of quality management and supply chain, their positive increasing effects that may be generated after their integration. For this purpose, the concept and definitions of each approach is studied, independently, their similarities and differences are recognized, and finally, the advantages of their integration are introduced.

  11. Chain Mixing and Chain Recurrent Iterated Function Systems

    OpenAIRE

    Nia, Mehdi Fatehi

    2016-01-01

    This paper considers the egodicity properties in iterated function systems. First, we will introduce chain mixing and chain transitive iterated function systems then some results and examples are presented to compare with these notions in discrete dynamical systems. As our main result, using adding machine maps and topological conjugacy we show that chain mixing, chain transitive and chain recurrence properties in iterated function systems are equivalent.

  12. Supply-Chain Optimization Template

    Science.gov (United States)

    Quiett, William F.; Sealing, Scott L.

    2009-01-01

    The Supply-Chain Optimization Template (SCOT) is an instructional guide for identifying, evaluating, and optimizing (including re-engineering) aerospace- oriented supply chains. The SCOT was derived from the Supply Chain Council s Supply-Chain Operations Reference (SCC SCOR) Model, which is more generic and more oriented toward achieving a competitive advantage in business.

  13. Essentials of supply chain management

    CERN Document Server

    Hugos, Michael H

    2011-01-01

    The latest thinking, strategies, developments, and technologies to stay current in supply chain management Presenting the core concepts and techniques of supply chain management in a clear, concise and easily readable style, the Third Edition of Essentials of Supply Chain Management outlines the most crucial tenets and concepts of supply chain management.

  14. Sex-linked recessive

    Science.gov (United States)

    Inheritance - sex-linked recessive; Genetics - sex-linked recessive; X-linked recessive ... X-linked recessive diseases most often occur in males. Males have only one X chromosome. A single recessive gene ...

  15. Sex-linked dominant

    Science.gov (United States)

    Inheritance - sex-linked dominant; Genetics - sex-linked dominant; X-linked dominant; Y-linked dominant ... can be either an autosomal chromosome or a sex chromosome. It also depends on whether the trait ...

  16. A novel time series link prediction method: Learning automata approach

    Science.gov (United States)

    Moradabadi, Behnaz; Meybodi, Mohammad Reza

    2017-09-01

    Link prediction is a main social network challenge that uses the network structure to predict future links. The common link prediction approaches to predict hidden links use a static graph representation where a snapshot of the network is analyzed to find hidden or future links. For example, similarity metric based link predictions are a common traditional approach that calculates the similarity metric for each non-connected link and sort the links based on their similarity metrics and label the links with higher similarity scores as the future links. Because people activities in social networks are dynamic and uncertainty, and the structure of the networks changes over time, using deterministic graphs for modeling and analysis of the social network may not be appropriate. In the time-series link prediction problem, the time series link occurrences are used to predict the future links In this paper, we propose a new time series link prediction based on learning automata. In the proposed algorithm for each link that must be predicted there is one learning automaton and each learning automaton tries to predict the existence or non-existence of the corresponding link. To predict the link occurrence in time T, there is a chain consists of stages 1 through T - 1 and the learning automaton passes from these stages to learn the existence or non-existence of the corresponding link. Our preliminary link prediction experiments with co-authorship and email networks have provided satisfactory results when time series link occurrences are considered.

  17. Global Supply Chain Management

    National Research Council Canada - National Science Library

    Mary Jo Lamberti; Mary Costello; Kenneth Getz

    2012-01-01

    ... clinical supplies will be needed. Some clinical supply managers have been using just-in-time or on-demand packaging and labeling2 or regional depots to address changes in the clinical supply chain strategy or forecasting during a trial...

  18. Exploration Supply Chain Simulation

    Science.gov (United States)

    2008-01-01

    The Exploration Supply Chain Simulation project was chartered by the NASA Exploration Systems Mission Directorate to develop a software tool, with proper data, to quantitatively analyze supply chains for future program planning. This tool is a discrete-event simulation that uses the basic supply chain concepts of planning, sourcing, making, delivering, and returning. This supply chain perspective is combined with other discrete or continuous simulation factors. Discrete resource events (such as launch or delivery reviews) are represented as organizational functional units. Continuous resources (such as civil service or contractor program functions) are defined as enabling functional units. Concepts of fixed and variable costs are included in the model to allow the discrete events to interact with cost calculations. The definition file is intrinsic to the model, but a blank start can be initiated at any time. The current definition file is an Orion Ares I crew launch vehicle. Parameters stretch from Kennedy Space Center across and into other program entities (Michaud Assembly Facility, Aliant Techsystems, Stennis Space Center, Johnson Space Center, etc.) though these will only gain detail as the file continues to evolve. The Orion Ares I file definition in the tool continues to evolve, and analysis from this tool is expected in 2008. This is the first application of such business-driven modeling to a NASA/government-- aerospace contractor endeavor.

  19. Cryochemical chain reactions

    Science.gov (United States)

    Barkalov, I. M.; Kiryukhin, D. P.

    The possibility of a chemical reaction near absolute zero has appeared doubtful since the beginning of the 1970s. The existing ideas must be revised after the radiation polymerization of formaldehyde at 4.2 K has been observed. In glassy systems, we have examined chain processes that occur under sharp (by five to six orders) changes in molecular mobility of the medium in the region of matrix devitrification. Quite unusual mechano-energetic chains of chemical conversion arise in the studied systems submerged in liquid helium. The chemical transformation initiated by local brittle fracture travels over the sample as an autowave. A series of experimental and theoretical investigations devoted to this interesting phenomenon are described. There is no generalization in this new region of chemistry up to this time. Many journal articles and reviews have been previously published only in Russian. The cycles of investigations of chain cryochemical reactions are the subject of this review. We hope that the investigation of the extraordinary peculiarities of chain cryochemical reactions should produce new ideas in chemical theory and industry.

  20. Galileo Chain Thermometer

    Science.gov (United States)

    Ucke, C.; Schlichting, H. J.

    2017-01-01

    This relatively rare thermometer has a rather unusual display: lower temperatures are located at the top of the scale, higher ones at the bottom. A sphere on a chain floats in a suitable liquid, sinking at high temperatures when the density of the liquid decreases and rising in the increased density at low temperatures. With reasonable effort and…

  1. Supply Chain Management

    Science.gov (United States)

    Bauer, Jürgen

    Die Produktionslogistik hat im Rahmen der Materialbeschaffung und der Belieferung von externen Kunden vielfältige Beziehungen zu Lieferanten und Kunden. Im Ansatz des Supply Chain Managements (Lieferkettenmanagement), kurz auch als SCM bezeichnet, versucht man, sowohl Lieferanten als auch Kunden in die gesamte Logistikplanung zu integrieren. SCM umfasst dabei vor allem folgende Aufgaben: Bedarfs- und Bestandsplanung der Materialien entlang der Lieferkette

  2. Innovation in Supply Chains

    DEFF Research Database (Denmark)

    Maier, Maximilian; Korbel, Jakob; Brem, Alexander

    2015-01-01

    . Moreover, along with the fourth industrial revolution – industry 4.0 – new technologies such as cyber physical systems are fast gaining popularity. Hence, based on the analysis of relevant literature, we further develop the supply chain committee model, developed by Kaluza et al. (2003) to demonstrate how...

  3. Markov Chain Monte Carlo

    Indian Academy of Sciences (India)

    GENERAL I ARTICLE. Markov Chain Monte Carlo. 1. ... Note that I have numbered only those squares that are. 'stable', 'i. e., do not have .... probability approaches 1 in the limit as t tends to infinity was obvious even without all this mathematics, since it is a common experience that all games of Ludo eventually end since.

  4. Serum Free Light Chains

    Science.gov (United States)

    ... High-sensitivity C-reactive Protein (hs-CRP) Histamine Histone Antibody HIV Antibody and HIV Antigen (p24) HIV ... coverstory.aspx. Accessed August 2010. (© 1995–2010). Unit Code 84190: Immunoglobulin Free Light Chains, Serum. Mayo Clinic, ...

  5. Supply chain reliability modelling

    Directory of Open Access Journals (Sweden)

    Eugen Zaitsev

    2012-03-01

    Full Text Available Background: Today it is virtually impossible to operate alone on the international level in the logistics business. This promotes the establishment and development of new integrated business entities - logistic operators. However, such cooperation within a supply chain creates also many problems related to the supply chain reliability as well as the optimization of the supplies planning. The aim of this paper was to develop and formulate the mathematical model and algorithms to find the optimum plan of supplies by using economic criterion and the model for the probability evaluating of non-failure operation of supply chain. Methods: The mathematical model and algorithms to find the optimum plan of supplies were developed and formulated by using economic criterion and the model for the probability evaluating of non-failure operation of supply chain. Results and conclusions: The problem of ensuring failure-free performance of goods supply channel analyzed in the paper is characteristic of distributed network systems that make active use of business process outsourcing technologies. The complex planning problem occurring in such systems that requires taking into account the consumer's requirements for failure-free performance in terms of supply volumes and correctness can be reduced to a relatively simple linear programming problem through logical analysis of the structures. The sequence of the operations, which should be taken into account during the process of the supply planning with the supplier's functional reliability, was presented.

  6. Economy, market and chain

    NARCIS (Netherlands)

    Sukkel, W.; Hommes, M.

    2009-01-01

    In their pursuit of growth and professionalisation, the Dutch organic sector focuses primarily on market development. But how do you stimulate the market for organic foods? This is the subject of many research projects concerning market, consumer preferences and the supply chain. These projects

  7. Improved chain control operations.

    Science.gov (United States)

    2010-01-01

    In California, field maintenance personnel use turntable signs to advise motorists of chain control conditions on rural : highways and freeways. To do this an operator has to park, exit the vehicle, turn the sign on the shoulder and then : walk acros...

  8. Heavy chain only antibodies

    DEFF Research Database (Denmark)

    Moghimi, Seyed Moein; Rahbarizadeh, Fatemeh; Ahmadvand, Davoud

    2013-01-01

    Unlike conventional antibodies, heavy chain only antibodies derived from camel contain a single variable domain (VHH) and two constant domains (CH2 and CH3). Cloned and isolated VHHs possess unique properties that enable them to excel conventional therapeutic antibodies and their smaller antigen...

  9. Supply Chain Costing

    DEFF Research Database (Denmark)

    Asmussen, Jesper Normann; Kristensen, Jesper; Wæhrens, Brian Vejrum

    Based Costing (ABC) på et forsyningskædeniveau – heri benævnt Supply Chain Costing (SCC). Udoverdefordelederfindesved ABCtilføjerSCCogså et økonomisk grundlag til det strategiske rationale, der ofte ligger bag opbygningen af virksomhedens forsyningskæde, og kan dermed medvirke til konkret...

  10. Managing Supply Chain Disruptions

    Science.gov (United States)

    2008-08-09

    objectives, alternatives, and the resources (Hayes, Wheelwright , & Clark, 1988). Further, Hayes et al. relate that planning should lead the...Chain Management Review, 7(6), pp 64. Hayes, R., Wheelwright , S. C., & Clark, K. B. (1988). Dynamic Manufacturing: Creating the Learning

  11. Efficiency of supply chain management. Strategic and operational approach

    Directory of Open Access Journals (Sweden)

    Grzegorz Lichocik

    2013-06-01

    Full Text Available Background: One of the most important issues subject to theoretical considerations and empirical studies is the measurement of efficiency of activities in logistics and supply chain management. Simultaneously, efficiency is one of the terms interpreted in an ambiguous and multi-aspect manner, depending on the subject of a study. The multitude of analytical dimensions of this term results in the fact that, apart from economic efficiency being the basic study area, other dimensions perceived as an added value by different groups of supply chain participants become more and more important. Methods: The objective of this paper is to attempt to explain the problem of supply chain management efficiency in the context of general theoretical considerations relating to supply chain management. The authors have also highlighted determinants and practical implications of supply chain management efficiency in strategic and operational contexts. The study employs critical analyses of logistics literature and the free-form interview with top management representatives of a company operating in the TSL sector. Results: We must find a comprehensive approach to supply chain efficiency including all analytical dimensions connected with real goods and services flow. An effective supply chain must be cost-effective (ensuring economic efficiency of a chain, functional (reducing processes, lean, minimising the number of links in the chain to the necessary ones, adapting supply chain participants' internal processes to a common objective based on its efficiency and ensuring high quality of services (customer-oriented logistics systems. Conclusions: Efficiency of supply chains is not only a task for which a logistics department is responsible as it is a strategic decision taken by the management as regards the method of future company's operation. Correctly planned and fulfilled logistics tasks may result in improving performance of a company as well as the whole

  12. X-linked adrenoleukodystrophy: pathogenesis and treatment

    NARCIS (Netherlands)

    Engelen, Marc; Kemp, Stephan; Poll-The, Bwee-Tien

    2014-01-01

    X-linked adrenoleukodystrophy (X-ALD) is a puzzling inborn error of metabolism with a strikingly heterogeneous clinical spectrum. All patients have mutations in the ABCD1 gene and accumulate very long chain fatty acids in all tissues. Virtually all male X-ALD patients develop adrenocortical

  13. An evaluation of supply chain management in a global perspective

    OpenAIRE

    Borges, Marco Antonio Viana

    2015-01-01

    Thecharacteristics and challenges of the integrated market, along with the risinginternational cooperation and vertical disintegration, have led to the notionthat firms are linked in a global supply chain. This study is focused onconcepts and models organized for the development of a theoretical essay inGlobal Supply Chain Management to evaluate characteristics and opportunities inthis field. It was used references that cover the global market factorsinvolving economic, cultural, political an...

  14. Research on the Logistics Supply Chain in Port Logistics Transportation

    OpenAIRE

    Wang Yan-liang

    2013-01-01

    The aim of this study is to improve and increase the logistics system effectiveness and to solve the problem of optimal movement of different flows. Logistics transport carrying the world on material resources transfer exchange important mission and economic development and our lives are closely linked, logistics chain logistics transport occupies an important position and in the e logistics chain in port logistics has play a decisive role. For many coastal countries port logistics is the eco...

  15. Supply Chain Management: from Linear Interactions to Networked Processes

    Directory of Open Access Journals (Sweden)

    Doina FOTACHE

    2006-01-01

    Full Text Available Supply Chain Management is a distinctive product, with a tremendous impact on the software applications market. SCM applications are back-end solutions intended to link suppliers, manufacturers, distributors and resellers in a production and distribution network, which allows the enterprise to track and consolidate the flows of materials and data trough the process of manufacturing and distribution of goods/services. The advent of the Web as a major means of conducting business transactions and business-tobusiness communications, coupled with evolving web-based supply chain management (SCM technology, has resulted in a transition period from “linear” supply chain models to "networked" supply chain models. The technologies to enable dynamic process changes and real time interactions between extended supply chain partners are emerging and being deployed at an accelerated pace.

  16. Fuzzy Entropy Method for Quantifying Supply Chain Networks Complexity

    Science.gov (United States)

    Zhang, Jihui; Xu, Junqin

    Supply chain is a special kind of complex network. Its complexity and uncertainty makes it very difficult to control and manage. Supply chains are faced with a rising complexity of products, structures, and processes. Because of the strong link between a supply chain’s complexity and its efficiency the supply chain complexity management becomes a major challenge of today’s business management. The aim of this paper is to quantify the complexity and organization level of an industrial network working towards the development of a ‘Supply Chain Network Analysis’ (SCNA). By measuring flows of goods and interaction costs between different sectors of activity within the supply chain borders, a network of flows is built and successively investigated by network analysis. The result of this study shows that our approach can provide an interesting conceptual perspective in which the modern supply network can be framed, and that network analysis can handle these issues in practice.

  17. The design of supply chains

    DEFF Research Database (Denmark)

    Bøge Sørensen, Lars

    2004-01-01

    Keywords Supply Chain Management, Supply Chain Design, Literature studyAbstract Argues stability is a design objective for supply chain design alongside cost, leadtime and responsiveness. Performs an extensive literature study on supply chain design,identifies methods, theories and objectives...... in the existing literature. Describes the conceptexternal specificity and how it's used to design supply chains. Using the concept upstream,archetypes of risk minimal and maximal design are identified. Downstream the conceptdescribes two viable scenarios, one minimizing the impact, the other minimizing...... theprobability of (intended) departure of a supply chain partner. Finally, principles for supplychain design are described and managerial outlined....

  18. Concurrent Product & Supply Chain Creation

    DEFF Research Database (Denmark)

    Gubi, Ebbe

    .e. by creating Focused Supply Chains. At the same time, customer satisfaction can be increased. As a second means to achieving a better fit between product and supply chain, the firm can deploy Design for Logistics, the discipline of considering the supply chain during product creation. The thesis sets out...... and supply chains should be created concurrently and integrated. The concept of Concurrent Product & Supply Chain Creation is introduced, and the two main components Focused Supply Chains and Design For Logistics are explained and exemplified by use of Bang & Olufsen....

  19. Decision-Making for Supply Chain Integration Supply Chain Integration

    CERN Document Server

    Lettice, Fiona; Durowoju, Olatunde

    2012-01-01

    Effective supply chain integration, and the tight co-ordination it creates, is an essential pre-requisite for successful supply chain management.  Decision-Making for Supply Chain Integration is a practical reference on recent research in the area of supply chain integration focusing on distributed decision-making problems. Recent applications of various decision-making tools for integrating supply chains are covered including chapters focusing on: •Supplier selection, pricing strategy and inventory decisions in multi-level supply chains, •RFID-enabled distributed decision-making, •Operational risk issues and time-critical decision-making for sensitive logistics nodes, Modelling end to end processes to improve supply chain integration, and •Integrated systems to improve service delivery and optimize resource use. Decision-Making for Supply Chain Integration provides an insight into the tools and methodologies of this field with support from real-life case studies demonstrating successful application ...

  20. Leptospira Immunoglobulin-Like Protein B (LigB Binds to Both the C-Terminal 23 Amino Acids of Fibrinogen αC Domain and Factor XIII: Insight into the Mechanism of LigB-Mediated Blockage of Fibrinogen α Chain Cross-Linking.

    Directory of Open Access Journals (Sweden)

    Ching-Lin Hsieh

    2016-09-01

    Full Text Available The coagulation system provides a primitive but effective defense against hemorrhage. Soluble fibrinogen (Fg monomers, composed of α, β and γ chains, are recruited to provide structural support for the formation of a hemostatic plug. Fg binds to platelets and is processed into a cross-linked fibrin polymer by the enzymatic clotting factors, thrombin and Factor XIII (FXIII. The newly formed fibrin-platelet clot can act as barrier to protect against pathogens from entering the bloodstream. Further, injuries caused by bacterial infections can be confined to the initial wound site. Many pathogenic bacteria have Fg-binding adhesins that can circumvent the coagulation pathway and allow the bacteria to sidestep containment. Fg expression is upregulated during lung infection providing an attachment surface for bacteria with the ability to produce Fg-binding adhesins. Fg binding by leptospira might play a crucial factor in Leptospira-associated pulmonary hemorrhage, the main factor contributing to lethality in severe cases of leptospirosis. The 12th domain of Leptospira immunoglobulin-like protein B (LigB12, a leptospiral adhesin, interacts with the C-terminus of FgαC (FgαCC. In this study, the binding site for LigB12 was mapped to the final 23 amino acids at the C-terminal end of FgαCC (FgαCC8. The association of FgαCC8 with LigB12 (ELISA, KD = 0.76 μM; SPR, KD = 0.96 μM was reduced by mutations of both charged residues (R608, R611 and H614 from FgαCC8; D1061 from LigB12 and hydrophobic residues (I613 from FgαCC8; F1054 and A1065 from LigB12. Additionally, LigB12 bound strongly to FXIII and also inhibited fibrin formation, suggesting that LigB can disrupt coagulation by suppressing FXIII activity. Here, the detailed binding mechanism of a leptospiral adhesin to a host hemostatic factor is characterized for the first time and should provide better insight into the pathogenesis of leptospirosis.

  1. Perioperative supply chain management.

    Science.gov (United States)

    Feistritzer, N R; Keck, B R

    2000-09-01

    Faced with declining revenues and increasing operating expenses, hospitals are evaluating numerous mechanisms designed to reduce costs while simultaneously maintaining quality care. Many facilities have targeted initial cost reduction efforts in the reduction of labor expenses. Once labor expenses have been "right sized," facilities have continued to focus on service delivery improvements by the optimization of the "supply chain" process. This report presents a case study of the efforts of Vanderbilt University Medical Center in the redesign of its supply chain management process in the department of Perioperative Services. Utilizing a multidisciplinary project management structure, 3 work teams were established to complete the redesign process. To date, the project has reduced costs by $2.3 million and enhanced quality patient care by enhancing the delivery of appropriate clinical supplies during the perioperative experience.

  2. Extended linear chain compounds

    CERN Document Server

    Linear chain substances span a large cross section of contemporary chemistry ranging from covalent polymers, to organic charge transfer com­ plexes to nonstoichiometric transition metal coordination complexes. Their commonality, which coalesced intense interest in the theoretical and exper­ imental solid state physics/chemistry communities, was based on the obser­ vation that these inorganic and organic polymeric substrates exhibit striking metal-like electrical and optical properties. Exploitation and extension of these systems has led to the systematic study of both the chemistry and physics of highly and poorly conducting linear chain substances. To gain a salient understanding of these complex materials rich in anomalous aniso­ tropic electrical, optical, magnetic, and mechanical properties, the conver­ gence of diverse skills and talents was required. The constructive blending of traditionally segregated disciplines such as synthetic and physical organic, inorganic, and polymer chemistry, crystallog...

  3. Streamlining the supply chain.

    Science.gov (United States)

    Neumann, Lydon

    2003-07-01

    Effective management of the supply chain requires attention to: Product management--formulary development and maintenance, compliance, clinical involvement, standardization, and demand-matching. Sourcing and contracting--vendor consolidation, GPO portfolio management, price leveling, content management, and direct contracting Purchasing and payment-cycle--automatic placement, web enablement, centralization, evaluated receipts settlement, and invoice matching Inventory and distribution management--"unofficial" and "official" locations, vendor-managed inventory, automatic replenishment, and freight management.

  4. Supply chain finance

    Directory of Open Access Journals (Sweden)

    Kasavica Petar

    2014-01-01

    Full Text Available The concept of supply chain finance is a response to global illiquidity, intensified through the global economic crisis and globalization of commercial and financial flows. The growing illiquidity undermines credit ratings of economic entities, thereby reducing the potential for achieving the projected goals (profitability and portfolio quality. In order to overcome this, banks have introduced certain products flexible to the requirements of specific transactions. The concerned products redirect the focus from a client's credit rating and risk to the credit rating and risk of a business partner (buyer, resulting in benefits for all transaction participants ('win-win-win'. Moreover, the activities are targeted at transaction analysis, i.e. the isolation and protection of the cash flow as the source of financial instrument's repayment. On the other hand, there has been an increasing number of transactions based on the risk of the commercial bank of the client's business partner, or on the risk of collateral (inventory. The focus is actually placed on the financing of adequate supply chain stages, given that counterparty relationship management has been proven to be crucial for efficient management of one's own business. The tensions existing in the relations between partners (increasingly long payment deadlines are in the basis of the supply chain finance concept. Decisions made by banks are based on the entire supply chain (wide information basis, thereby shifting the focus from the product (as was the case before the crisis to the client's needs. Thus, decisions become increasingly comprehensive, quicker, and more precise, and portfolios less risky. Through the individual portfolio of banks, the market of national economies also becomes safer and more liquid. These are rather profitable transactions, because, due to the risk transfer, financing is enabled to companies to whom classic crediting in most cases is not available.

  5. Supply Chain Initiatives Database

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-11-01

    The Supply Chain Initiatives Database (SCID) presents innovative approaches to engaging industrial suppliers in efforts to save energy, increase productivity and improve environmental performance. This comprehensive and freely-accessible database was developed by the Institute for Industrial Productivity (IIP). IIP acknowledges Ecofys for their valuable contributions. The database contains case studies searchable according to the types of activities buyers are undertaking to motivate suppliers, target sector, organization leading the initiative, and program or partnership linkages.

  6. Design of supply chain in fuzzy environment

    Science.gov (United States)

    Rao, Kandukuri Narayana; Subbaiah, Kambagowni Venkata; Singh, Ganja Veera Pratap

    2013-05-01

    Nowadays, customer expectations are increasing and organizations are prone to operate in an uncertain environment. Under this uncertain environment, the ultimate success of the firm depends on its ability to integrate business processes among supply chain partners. Supply chain management emphasizes cross-functional links to improve the competitive strategy of organizations. Now, companies are moving from decoupled decision processes towards more integrated design and control of their components to achieve the strategic fit. In this paper, a new approach is developed to design a multi-echelon, multi-facility, and multi-product supply chain in fuzzy environment. In fuzzy environment, mixed integer programming problem is formulated through fuzzy goal programming in strategic level with supply chain cost and volume flexibility as fuzzy goals. These fuzzy goals are aggregated using minimum operator. In tactical level, continuous review policy for controlling raw material inventories in supplier echelon and controlling finished product inventories in plant as well as distribution center echelon is considered as fuzzy goals. A non-linear programming model is formulated through fuzzy goal programming using minimum operator in the tactical level. The proposed approach is illustrated with a numerical example.

  7. Port supply chain integration : analyzing biofuel supply chains

    NARCIS (Netherlands)

    Stevens, Leonie C. E.; Vis, Iris F. A.

    2016-01-01

    This paper focuses on port supply chain integration to strengthen operational and business performance. We provide a structured and comprehensive method to enable port supply chain integration and demonstrate its applicability to the biofuel supply chain. We define the value proposition, role,

  8. Rapid Acquisition of Choice and Timing and the Provenance of the Terminal-Link Effect

    Science.gov (United States)

    Kyonka, Elizabeth G. E.; Grace, Randolph C.

    2010-01-01

    Eight pigeons responded in a concurrent-chains procedure in which terminal-link schedules changed pseudorandomly across sessions. Pairs of terminal-link delays either summed to 15 s or to 45 s. Across sessions, the location of the shorter terminal link changed according to a pseudorandom binary sequence. On some terminal links, food was withheld…

  9. Environmentally conscious supply chain design

    OpenAIRE

    ALTMANN, MICHAEL

    2015-01-01

    Sustainability has become a critical topic in all areas of supply chain management. As discussed earlier, drivers for this development can be identified as both internal and external phenomena. Since customers are one of the key stakeholders in supply chain management, special attention is paid to the impact of costumers´ behavior on sustainable supply chain design decisions. In this context, two main research questions were analyzed: 1.What is the appropriate way to design a supply chain...

  10. Supply Chain Dynamics in Asia

    OpenAIRE

    Ruth Banomyong

    2009-01-01

    Supply chain management in Asia is a relatively novel topic but a key challenge for all Asian based manufacturers and traders when trying to integrate into the "global market". The purpose of the paper is to describe key supply chain issues faced in Asia. These issues are related to supply chain security that forces Asian firms to comply with numerous requirements as well as the importance of a properly managed supply chain in enhancing firms' competitiveness. The critical role played by Asia...

  11. Pushing or sharing as value-driven strategies for societal change in global supply chains: two case studies in the British-South African fresh fruit supply chain

    NARCIS (Netherlands)

    Müller, C.; Vermeulen, W.J.V.; Glasbergen, P.

    2012-01-01

    Business strategy is linked to organisational values and culture, which is determined to some extent by national culture. This can provide a challenge in a global supply chain where culture and values at one end of the chain do not correspond with culture at the other end. This paper contends that

  12. Process Algebra and Markov Chains

    NARCIS (Netherlands)

    Brinksma, Hendrik; Hermanns, H.; Brinksma, Hendrik; Hermanns, H.; Katoen, Joost P.

    This paper surveys and relates the basic concepts of process algebra and the modelling of continuous time Markov chains. It provides basic introductions to both fields, where we also study the Markov chains from an algebraic perspective, viz. that of Markov chain algebra. We then proceed to study

  13. On chains of centered valuations

    Directory of Open Access Journals (Sweden)

    Rachid Chibloun

    2003-01-01

    Full Text Available We study chains of centered valuations of a domain A and chains of centered valuations of A [X1,…,Xn] corresponding to valuations of A. Finally, we make some applications to chains of valuations centered on the same ideal of A [X1,…,Xn] and extending the same valuation of A.

  14. Academic Education Chain Operation Model

    OpenAIRE

    Ruskov, Petko; Ruskov, Andrey

    2007-01-01

    This paper presents an approach for modelling the educational processes as a value added chain. It is an attempt to use a business approach to interpret and compile existing business and educational processes towards reference models and suggest an Academic Education Chain Operation Model. The model can be used to develop an Academic Chain Operation Reference Model.

  15. Thermodynamics of Dipolar Chain Systems

    DEFF Research Database (Denmark)

    R. Armstrong, J.; Zinner, Nikolaj Thomas; V. Fedorov, D.

    2012-01-01

    of the intralayer repulsion and quantum statistical requirements in systems with more than one chain. Specifically, we consider the case of two chains and solve the problem analytically within the harmonic Hamiltonian approach which is accurate for large dipole moments. The case of three chains is calculated...

  16. Designing structural supply chain flexibility

    NARCIS (Netherlands)

    Mulinski, Ksawery Jan

    2012-01-01

    In a continuously changing business environment the role of supply chain flexibility is constantly increasing. A flexible supply chain can ensure survival in quickly changing market conditions as well as enable sustainable growth. This thesis explores the topic of supply chain flexibility with focus

  17. A chain of FPU cells

    NARCIS (Netherlands)

    Verhulst, F.

    2015-01-01

    In contrast to the classical Fermi-Pasta-Ulam (FPU) chain, the inhomogeneous FPU chain shows nearly all the principal resonances. Using this fact, we can construct a periodic FPU chain of low dimension, for instance a FPU cell of four degrees-of-freedom, that can be used as a building block for a

  18. Simple chain grammars and languages

    NARCIS (Netherlands)

    Nijholt, Antinus

    1979-01-01

    A subclass of the LR(0)-grammars, the class of simple chain grammars is introduced. Although there exist simple chain grammars which are not LL(k) for any k>0, this new class of grammars is very closely related to the LL(1) and simple LL(1) grammars. In fact it can be shown that every simple chain

  19. Musical Markov Chains

    Science.gov (United States)

    Volchenkov, Dima; Dawin, Jean René

    A system for using dice to compose music randomly is known as the musical dice game. The discrete time MIDI models of 804 pieces of classical music written by 29 composers have been encoded into the transition matrices and studied by Markov chains. Contrary to human languages, entropy dominates over redundancy, in the musical dice games based on the compositions of classical music. The maximum complexity is achieved on the blocks consisting of just a few notes (8 notes, for the musical dice games generated over Bach's compositions). First passage times to notes can be used to resolve tonality and feature a composer.

  20. Monte Carlo without chains

    Energy Technology Data Exchange (ETDEWEB)

    Chorin, Alexandre J.

    2007-12-12

    A sampling method for spin systems is presented. The spin lattice is written as the union of a nested sequence of sublattices, all but the last with conditionally independent spins, which are sampled in succession using their marginals. The marginals are computed concurrently by a fast algorithm; errors in the evaluation of the marginals are offset by weights. There are no Markov chains and each sample is independent of the previous ones; the cost of a sample is proportional to the number of spins (but the number of samples needed for good statistics may grow with array size). The examples include the Edwards-Anderson spin glass in three dimensions.

  1. Detox fashion supply chain

    CERN Document Server

    2017-01-01

    This first volume on detox fashion discusses various interesting topics including a Toxic-Free Supply Chain for Textiles and Clothing; Environmental Issues in Textiles; Global Regulations, Restrictions & Research; Making the Change: Consumer Adoption of Sustainable Fashion; and Strategies for Detoxing Your Wardrobe. It provides an overview of the chemical-related issues confronting the fashion sector, summarizes global regulations, and discusses how to make the change by changing consumers’ attitude towards adopting sustainable fashion, as well as the best strategies for detoxing our wardrobes.

  2. Modeling methodology for supply chain synthesis and disruption analysis

    Science.gov (United States)

    Wu, Teresa; Blackhurst, Jennifer

    2004-11-01

    The concept of an integrated or synthesized supply chain is a strategy for managing today's globalized and customer driven supply chains in order to better meet customer demands. Synthesizing individual entities into an integrated supply chain can be a challenging task due to a variety of factors including conflicting objectives, mismatched incentives and constraints of the individual entities. Furthermore, understanding the effects of disruptions occurring at any point in the system is difficult when working toward synthesizing supply chain operations. Therefore, the goal of this research is to present a modeling methodology to manage the synthesis of a supply chain by linking hierarchical levels of the system and to model and analyze disruptions in the integrated supply chain. The contribution of this research is threefold: (1) supply chain systems can be modeled hierarchically (2) the performance of synthesized supply chain system can be evaluated quantitatively (3) reachability analysis is used to evaluate the system performance and verify whether a specific state is reachable, allowing the user to understand the extent of effects of a disruption.

  3. Synthetic polyubiquitinated α-Synuclein reveals important insights into the roles of the ubiquitin chain in regulating its pathophysiology

    National Research Council Canada - National Science Library

    Mahmood Haj-Yahya; Bruno Fauvet; Yifat Herman-Bachinsky; Mirva Hejjaoui; Sudhir N. Bavikar; Subramanian Vedhanarayanan Karthikeyan; Aaron Ciechanover; Hilal A. Lashuel; Ashraf Brik

    2013-01-01

    ...) chains to a specific substrate. Here, we describe chemical and semisynthetic strategies for site-specific incorporation of K48-linked di- or tetra-Ub chains onto the side chain of Lys12 of α-Synuclein (α-Syn...

  4. Clipboard: A branched chain fatty acid promotes cold adaptation in ...

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Biosciences; Volume 28; Issue 4. Clipboard: A branched chain fatty acid promotes cold adaptation in bacteria. M K Chattopadhyay M V Jagannadham. Volume 28 Issue 4 June 2003 pp 363-364. Fulltext. Click here to view fulltext PDF. Permanent link:

  5. Issues and Challenges in Self-Sustaining Response Supply Chains

    Science.gov (United States)

    2013-04-01

    Lexical Link Analysis (LLA) to Strengthen the Defense Acquisition Process Ying Zhao, Don Brutzman, and Douglas J. MacKinnon Naval Postgraduate School...Continuous Review Supply Chain Models Barry R. Cobb , Virginia Military Institute Alan W. Johnson, Air Force Institute of Technology Improving Multi

  6. Addressing Counterfeit Parts in the DoD Supply Chain

    Science.gov (United States)

    2013-04-01

    Social-Media Brainstorming With Lexical Link Analysis (LLA) to Strengthen the Defense Acquisition Process Ying Zhao, Don Brutzman, and Douglas J...Lead Time Demand Modeling in Continuous Review Supply Chain Models Barry R. Cobb , Virginia Military Institute Alan W. Johnson, Air Force Institute of

  7. The golden chain: family, civil society, and the state

    NARCIS (Netherlands)

    Nautz, J.; Ginsborg, P.; Nijhuis, T.

    2013-01-01

    The family can be viewed as one of the links in a "golden chain" connecting individuals, the private sphere, civil society, and the democratic state; as potentially an important source of energy for social activity; and as the primary institution that socializes and diffuses the values and norms

  8. 188 An Empirical Investigation of Value-Chain Analysis and ...

    African Journals Online (AJOL)

    User

    described and popularized by Michael Porter in his 1985 bestseller. “Competitive Advantage: creating and sustaining superior performance”. According to Ikwouria and Gate (2008), value chain is the sequence of activities required to make a product or provide a service. It is a linked set of value-creating activities all the way ...

  9. Effects of collaborative supply chain solutions on strategic performance management

    NARCIS (Netherlands)

    Rachan, Wilfred

    2012-01-01

    Throughout this research the focus has been on unraveling of the factors and relations that link different aspects of collaborative workflow to strategic performance management. However, the same issues that applied to strategic performance management of supply chains also apply to other areas of

  10. Compactification of Superstrings and Chain or Oriented Strings in Interactions

    Energy Technology Data Exchange (ETDEWEB)

    Morales, Robert O.

    2000-04-10

    Superstring theories command the study of their various possible compactifications, and their consequence physics. Thus, the role of topology is likely to be far more central, in particular in ten-dimensional physics. Topological invariants on a chain of oriented strings in interaction are discussed. Attempts to link superstrings with the reality of the physical world in four dimensions are discussed.

  11. Creative industries value chain: The value chain logic in supply chain relationships

    Directory of Open Access Journals (Sweden)

    Emilia Madudová

    2017-09-01

    Full Text Available The purpose of this paper is to provide a deeper look into value chain logic in supply chain relationships in a creative industries value chains. In recent years, value has been recognized as a key factor in better understanding of consumer behavior and gaining a competitive advantage. In a value chain, added value should be defined at every step of the chain. There should be defined activity which adds value as well as the activity that subtracts any value. The total value can be then calculated as the sum of the total value built up all throughout the value chain. Paper mostly analyses creative industries of advertising, architecture, and design. The presented model describes and analyzes the industry participants, value chain processes, support and related environment, and evaluates the relationship of stakeholders. The paper also takes into account the creation of value chain approach that describes the vertical and horizontal linkages. The chain of values represents the coordinated set of kinds of activity which create value for the enterprise, beginning from initial sources of raw materials for suppliers of this enterprise up to the finished goods delivered to the end user including service of the consumer. The value chain conception is important for the identification and development of the enterprise. The value creation activities can be a core competitive advantage which center on fostering relationships with key actors who can derive benefits from each other’s value chain.

  12. Linked data management

    CERN Document Server

    Hose, Katja; Schenkel, Ralf

    2014-01-01

    Linked Data Management presents techniques for querying and managing Linked Data that is available on today’s Web. The book shows how the abundance of Linked Data can serve as fertile ground for research and commercial applications. The text focuses on aspects of managing large-scale collections of Linked Data. It offers a detailed introduction to Linked Data and related standards, including the main principles distinguishing Linked Data from standard database technology. Chapters also describe how to generate links between datasets and explain the overall architecture of data integration systems based on Linked Data. A large part of the text is devoted to query processing in different setups. After presenting methods to publish relational data as Linked Data and efficient centralized processing, the book explores lookup-based, distributed, and parallel solutions. It then addresses advanced topics, such as reasoning, and discusses work related to read-write Linked Data for system interoperation. Desp...

  13. NNSA TRITIUM SUPPLY CHAIN

    Energy Technology Data Exchange (ETDEWEB)

    Wyrick, Steven [Savannah River National Laboratory, Aiken, SC, USA; Cordaro, Joseph [Savannah River National Laboratory, Aiken, SC, USA; Founds, Nanette [National Nuclear Security Administration, Albuquerque, NM, USA; Chambellan, Curtis [National Nuclear Security Administration, Albuquerque, NM, USA

    2013-08-21

    Savannah River Site plays a critical role in the Tritium Production Supply Chain for the National Nuclear Security Administration (NNSA). The entire process includes: • Production of Tritium Producing Burnable Absorber Rods (TPBARs) at the Westinghouse WesDyne Nuclear Fuels Plant in Columbia, South Carolina • Production of unobligated Low Enriched Uranium (LEU) at the United States Enrichment Corporation (USEC) in Portsmouth, Ohio • Irradiation of TPBARs with the LEU at the Tennessee Valley Authority (TVA) Watts Bar Reactor • Extraction of tritium from the irradiated TPBARs at the Tritium Extraction Facility (TEF) at Savannah River Site • Processing the tritium at the Savannah River Site, which includes removal of nonhydrogen species and separation of the hydrogen isotopes of protium, deuterium and tritium.

  14. Genetics Home Reference: medium-chain acyl-CoA dehydrogenase deficiency

    Science.gov (United States)

    ... Acylcarnitine (PDF) Formal Treatment/Management Guidelines (2 links) British Inherited Metabolic Disease Group: MCADD Dietary Management Guidelines ( ... Orphanet: Medium chain acyl-CoA dehydrogenase deficiency Screening, Technology, and Research in Genetics Virginia Department of Health ( ...

  15. Genetics Home Reference: short-chain acyl-CoA dehydrogenase deficiency

    Science.gov (United States)

    ... Living with Inherited Metabolic Disease (CLIMB) Children's Mitochondrial Disease Network (UK) FOD (Fatty Oxidation Disorders) Family Support Group National Organization for Rare Disorders (NORD) United Mitochondrial Disease Foundation GeneReviews (1 link) Short-Chain Acyl-CoA ...

  16. Mathematical Programming Model of Biodiesel Supply Chain in Colombia

    Directory of Open Access Journals (Sweden)

    Johan Alexander Aranda Pinilla

    2014-06-01

    in order to coordinate a structured way fl ow of resources between the links in the chain starting with “harvesting” going through the middle steps of “extraction” and “conversion” until the fi nal step “mixture “, which are involved in the supply network. The goal of the model is to determine a distribution plan of palm, oil, biodiesel and diesel throughout the chain, along with a production and inventory plan, and a capacity increase plan for biorefi neries in a way that minimizes the total cost of the production chain over a predefi ned planning horizon. The application of the model results in a projection to the year 2043 showing the behavior of the chain, specifi cally soil requirements for such production levels.

  17. AN EVALUATION OF SUPPLY CHAIN MANAGEMENT IN A GLOBAL PERSPECTIVE

    Directory of Open Access Journals (Sweden)

    Marco Antonio Viana Borges

    2015-03-01

    Full Text Available Thecharacteristics and challenges of the integrated market, along with the risinginternational cooperation and vertical disintegration, have led to the notionthat firms are linked in a global supply chain. This study is focused onconcepts and models organized for the development of a theoretical essay inGlobal Supply Chain Management to evaluate characteristics and opportunities inthis field. It was used references that cover the global market factorsinvolving economic, cultural, political and demographic issues that representopportunities and barriers for going global.  It was indentified that the challenge relatedto the international operations is to develop a global strategy considering theinfluence of political and economic factors in the trade, culturalcharacteristics, supply chain costs, infrastructure, technology, market andcompetitive rules. From the elements raised from theory for the configurationof a global supply chain approach, this study also identified gaps andquestions for future research agenda in the area.

  18. Advances in single chain technology.

    Science.gov (United States)

    Gonzalez-Burgos, Marina; Latorre-Sanchez, Alejandro; Pomposo, José A

    2015-10-07

    The recent ability to manipulate and visualize single atoms at atomic level has given rise to modern bottom-up nanotechnology. Similar exquisite degree of control at the individual polymeric chain level for producing functional soft nanoentities is expected to become a reality in the next few years through the full development of so-called "single chain technology". Ultra-small unimolecular soft nano-objects endowed with useful, autonomous and smart functions are the expected, long-term valuable output of single chain technology. This review covers the recent advances in single chain technology for the construction of soft nano-objects via chain compaction, with an emphasis in dynamic, letter-shaped and compositionally unsymmetrical single rings, complex multi-ring systems, single chain nanoparticles, tadpoles, dumbbells and hairpins, as well as the potential end-use applications of individual soft nano-objects endowed with useful functions in catalysis, sensing, drug delivery and other uses.

  19. Implementation of Multi-Body Dynamics Simulation for the Conveyor Chain Drive System

    Directory of Open Access Journals (Sweden)

    Suvanjumrat Chakrit

    2017-01-01

    Full Text Available The conveyor chain drive system which included four sprockets, four flat bars (chain guides and one conveyor chain had been assembled into commercial software, MSC.ADAMS. The conveyor chain was connected with rollers for running on the chain guides. The multi-body dynamics (MBD simulation was implemented to study the large displacement of chain components which happened during rotations of the symmetric model of the conveyor chain drive system. The physical experiment had obtained by construction of the conveyor chain drive system regarding the MBD model. The speeds of chain drive were adjusted by a gear motor with a converter. The trajectory of conveyor chain links which respectively meshed and ran on sprockets and chain guides was recorded by a high speed camera. Furthermore, impact-contact forces by a collision of components in the conveyor chain drive system during rotation were analysis. The comparison between MBD simulation and physical experiment of the conveyor chain drive system was performed for validation of simulation models. The MBD simulation results were in good agreement with the experimental data which obtained an average error of 3.95%.

  20. Chain formation of metal atoms

    DEFF Research Database (Denmark)

    Bahn, Sune Rastad; Jacobsen, Karsten Wedel

    2001-01-01

    The possibility of formation of single-atomic chains by manipulation of nanocontacts is studied for a selection of metals (Ni, Pd, Pt, Cu, Ag, Au). Molecular dynamics simulations show that the tendency for chain formation is strongest for Au and Pt. Density functional theory calculations indicate...... that the metals which form chains exhibit pronounced many-atom interactions with strong bonding in low coordinated systems....

  1. Chains, bombs, potrzebies and slugs

    Science.gov (United States)

    Jewess, Mike; McDowell, Alex; Maxfield, Stephen; Hunt, A. G.; Hicks, Bruce

    2010-03-01

    I read with pleasure Robert Crease's article on unusual units (February pp17-19). However, the article stated that an acre is 10×10 chains, when it is in fact 10×1 chains. Incidentally, a distance of 10 chains (220 yards) is known as a furlong, a word that suggests the length of a ploughed furrow and that is still used in horse-racing.

  2. AN EXPLORATORY APPROACH TO INTEGRATION OF BUSINESS PRACTICES IN SUPPLY CHAIN MANAGEMENT

    OpenAIRE

    Constangioara Alexandru

    2014-01-01

    Literature on supply chain management focuses increasingly on the topic of supply chain integration. Morash and Bowersox (1989) show that integration links relationships, activities, functions, processes and locations. Integration links a firm with its customers, suppliers and other channel members. The empirical research brings supporting evidence on the theory that organizations achieve the desired competitive advantage only by focusing on one strategy – either collaborative closeness or op...

  3. Maximum Kolmogorov-Sinai Entropy Versus Minimum Mixing Time in Markov Chains

    Science.gov (United States)

    Mihelich, M.; Dubrulle, B.; Paillard, D.; Kral, Q.; Faranda, D.

    2018-01-01

    We establish a link between the maximization of Kolmogorov Sinai entropy (KSE) and the minimization of the mixing time for general Markov chains. Since the maximisation of KSE is analytical and easier to compute in general than mixing time, this link provides a new faster method to approximate the minimum mixing time dynamics. It could be interesting in computer sciences and statistical physics, for computations that use random walks on graphs that can be represented as Markov chains.

  4. Exergy analysis : a tool to study the sustainability of food supply chains

    NARCIS (Netherlands)

    Apaiah, R.K.; Linnemann, A.R.; Kooi, van der H.J.

    2006-01-01

    This paper explores the potential of using exergy analysis to study and compare the environmental impact of food supply chains. The method identifies the links where exergy destruction takes place and shows where improvements are possible to minimize this destruction. The supply chains of three

  5. Managing the Global Supply Chain

    DEFF Research Database (Denmark)

    Skjøtt-Larsen, Tage; Schary, Philip B.; Mikkola, Juliana Hsuan

    The world today faces global competition. The supply chain is vital part of the globalization process. Presenting a global view of the scope and complexity of supply chain management, this book reflects the rapid change that has taken place within the supply chain and its environment. This new...... edition has been fully updated with recent changes in concepts, technology and practice. Integration and collaboration are keywords in future competition. Firms must be agile and lean at the same time. The book gives an insightful overview of the conceptual foundations of the global supply chain, as...

  6. Social Media and Supply Chain

    Directory of Open Access Journals (Sweden)

    Sonja Markova

    2013-02-01

    Full Text Available Web 2.0, also referred to as social media, is the use of the World Wide Web to increase creativity, information sharing, and collaboration among users. Social media is driving the rethinking of many of the principles of economics. The use of social media within supply chains is lagging behind their usage for other operational functions, however supply chain management is evolving into supply chain management 2.0.The purpose of this article is to provide researches of the supply chain management a reference with the main concepts of social media: social profiles, social applications, brand outposts and communities, and the social ecosystem.

  7. The Supply Chain Has No Clothes: Technology Adoption of Blockchain for Supply Chain Transparency

    Directory of Open Access Journals (Sweden)

    Kristoffer Francisco

    2018-01-01

    Full Text Available Blockchain technology, popularized by Bitcoin cryptocurrency, is characterized as an open-source, decentralized, distributed database for storing transaction information. Rather than relying on centralized intermediaries (e.g., banks this technology allows two parties to transact directly using duplicate, linked ledgers called blockchains. This makes transactions considerably more transparent than those provided by centralized systems. As a result, transactions are executed without relying on explicit trust [of a third party], but on the distributed trust based on the consensus of the network (i.e., other blockchain users. Applying this technology to improve supply chain transparency has many possibilities. Every product has a long and storied history. However, much of this history is presently obscured. Often, when negative practices are exposed, they quickly escalate to scandalous, and financially crippling proportions. There are many recent examples, such as the exposure of child labor upstream in the manufacturing process and the unethical use of rainforest resources. Blockchain may bring supply chain transparency to a new level, but presently academic and managerial adoption of blockchain technologies is limited by our understanding. To address this issue, this research uses the Unified Theory of Acceptance and Use of Technology (UTAUT and the concept of technology innovation adoption as a foundational framework for supply chain traceability. A conceptual model is developed and the research culminates with supply chain implications of blockchain that are inspired by theory and literature review.

  8. Requirements of supply chain management in differentiating European pork chains

    NARCIS (Netherlands)

    Trienekens, J.H.; Wognum, P.M.

    2013-01-01

    This paper summarizes results obtained by research into pork chain management in the EU Integrated Project Q-Porkchains. Changing demands for intrinsic and extrinsic quality attributes of pork products impact the way supply chain management should be organized from the farmer down to the consumer.

  9. Supply chain design approaches for supply chain resilience: A qualitative study of South African fast-moving consumer goods grocery manufacturers

    Directory of Open Access Journals (Sweden)

    Assilah Agigi

    2016-01-01

    Full Text Available Orientation: In today’s globalised and complex business environment, firms are ever more vulnerable to supply chain disruptions, originating both internally and externally from the supply chain. Supply chain resilience minimises the impact of a disruption through design approaches, which allows the supply chain to respond appropriately to disruptive events.Research purpose: This article investigated the supply chain risks faced by grocery manufacturers in the South African fast-moving consumer goods (FMCG industry and explored supply chain design approaches that enable supply chain resilience.Motivation for the study: South African grocery manufacturers are faced with distinct risks. Whilst supply chain risk management studies have provided firms with certain guidelines to mitigate risk, supply chains are still vulnerable to unanticipated risks. Literature on supply chain resilience in the South African context is scant. The concept of supply chain resilience provides firms with strategies that are built into the supply chain that allow firms to react and recover swiftly from disruptions. Furthermore, supply chain resilience strategies assist firms in becoming less vulnerable to possible disruptions.Research design approach and method: This study was conducted by using a descriptive qualitative research design. Data were collected through semi-structured interviews with senior supply chain practitioners specifically within the South African FMCG grocery manufacturing industry.Main findings: The study found that labour unrest is the most common risk faced by the industry. Furthermore, strategic stock and supply chain mapping are of the most useful design approaches to enhance supply chain resilience.Practical/managerial implications: The study provides managers with new insights in guiding supply chain design decisions for resilient supply chains. Through the identification of risks and appropriate solutions linked to the various risks, the

  10. Requirements of supply chain management in differentiating European pork chains.

    Science.gov (United States)

    Trienekens, Jacques; Wognum, Nel

    2013-11-01

    This paper summarizes results obtained by research into pork chain management in the EU Integrated Project Q-Porkchains. Changing demands for intrinsic and extrinsic quality attributes of pork products impact the way supply chain management should be organized from the farmer down to the consumer. The paper shows the importance of Quality Management Systems for integrating supply chains and enhancing consumer confidence. The paper also presents innovations in information system integration for aligning information exchange in the supply chain and logistics concepts based on innovative measurement technologies at the slaughterhouse stage. In the final section research challenges towards sustainable pork supply chains satisfying current consumer demands are presented. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Supply chain strategies in the context of an e-commerce chain (e-chain)

    OpenAIRE

    João Gilberto Mendes do Reis; Pedro Luiz de Oliveira Costa Neto; José Paulo Alves Fusco; Sivanilza Teixeira Machado

    2014-01-01

    This paper purpose to explore the relationships between supply chain strategies and product performance in retail e-commerce. In this case, we concern that in current, in order to bear up under competition, organizations have to manage their supply chains so that they meet the needs of their final customers. With this concept in mind, the research presented in this study focuses on establishing the right strategy for supply chains according to their product segment. Thus, after a Literature R...

  12. SUPPLY CHAIN STRATEGIES IN THE CONTEXT OF AN E-COMMERCE CHAIN (E-CHAIN

    Directory of Open Access Journals (Sweden)

    João Gilberto Mendes do Reis

    2014-05-01

    Full Text Available This paper purpose to explore the relationships between supply chain strategies and product performance in retail e-commerce. In this case, we concern that in current, in order to bear up under competition, organizations have to manage their supply chains so that they meet the needs of their final customers. With this concept in mind, the research presented in this study focuses on establishing the right strategy for supply chains according to their product segment. Thus, after a Literature Review, the paper explain a methodology based in different authors studies. Finally the article focuses on a pratical case in e-commerce retail that describes its application in this field. The research shows that it is possible to use a methodology for classifying supply chains using chain strategies and product features. The use of the right strategy for supply chains will improve the competitive advantage of businesses. One limitation is that the methodology study focuses on only two e-commerce segment; future studies may go further in refining the proposed framework for other segments. The aim of this research is to offer businesses a model for evaluating supply chains, allowing them to improve the performance of their products and services by using the right strategy for supply chains. The classification proposal of this paper presents an original model for classification of supply chains based on different studies on the theme.

  13. Linked Station Neighbors

    Data.gov (United States)

    Federal Communications Commission — This file that is a subset of the Linked-Station Set file. This file specifies, for each U.S. or impeding Canadian station part of a linked station set, the set of...

  14. Effect of chain stiffness on the structure of single-chain polymer nanoparticles

    Science.gov (United States)

    Moreno, Angel J.; Bacova, Petra; Lo Verso, Federica; Arbe, Arantxa; Colmenero, Juan; Pomposo, José A.

    2018-01-01

    Polymeric single-chain nanoparticles (SCNPs) are soft nano-objects synthesized by purely intramolecular cross-linking of single polymer chains. By means of computer simulations, we investigate the conformational properties of SCNPs as a function of the bending stiffness of their linear polymer precursors. We investigate a broad range of characteristic ratios from the fully flexible case to those typical of bulky synthetic polymers. Increasing stiffness hinders bonding of groups separated by short contour distances and increases looping over longer distances, leading to more compact nanoparticles with a structure of highly interconnected loops. This feature is reflected in a crossover in the scaling behaviour of several structural observables. The scaling exponents change from those characteristic for Gaussian chains or rings in θ-solvents in the fully flexible limit, to values resembling fractal or ‘crumpled’ globular behaviour for very stiff SCNPs. We characterize domains in the SCNPs. These are weakly deformable regions that can be seen as disordered analogues of domains in disordered proteins. Increasing stiffness leads to bigger and less deformable domains. Surprisingly, the scaling behaviour of the domains is in all cases similar to that of Gaussian chains or rings, irrespective of the stiffness and degree of cross-linking. It is the spatial arrangement of the domains which determines the global structure of the SCNP (sparse Gaussian-like object or crumpled globule). Since intramolecular stiffness can be varied through the specific chemistry of the precursor or by introducing bulky side groups in its backbone, our results propose a new strategy to tune the global structure of SCNPs.

  15. Models for supply chain reengineering

    NARCIS (Netherlands)

    Trienekens, J.H.; Hvolby, H.H.

    2001-01-01

    The goal of this paper is to provide a first step in the development of a coherent set of modelling methods for supply chain reengineering. This paper shows that different fields of attention in supply chain management should be approached with different modelling methods. Three modelling methods

  16. Academic Education Chain Operation Model

    NARCIS (Netherlands)

    Ruskov, Petko; Ruskov, Andrey

    2007-01-01

    This paper presents an approach for modelling the educational processes as a value added chain. It is an attempt to use a business approach to interpret and compile existing business and educational processes towards reference models and suggest an Academic Education Chain Operation Model. The model

  17. YMCA: Why Markov Chain Algebra?

    NARCIS (Netherlands)

    Bravetti, Mario; Hermanns, H.; Katoen, Joost P.; Aceto, L.; Gordon, A.

    2006-01-01

    Markov chains are widely used to determine system performance and reliability characteristics. The vast majority of applications considers continuous-time Markov chains (CTMCs). This note motivates how concurrency theory can be extended (as opposed to twisted) to CTMCs. We provide the core

  18. Negotiations in Supply Chain Management

    DEFF Research Database (Denmark)

    Zachariassen, Frederik

    2008-01-01

    negotiation literature. Subsequently, an empirical case study is presented, which explicitly aims at exploring the role of negotiations between members of a supply chain. Based on the findings, the paper concludes on specific, normative guidelines for negotiations for improved supply chain competitiveness...

  19. Verifying the Hanging Chain Model

    Science.gov (United States)

    Karls, Michael A.

    2013-01-01

    The wave equation with variable tension is a classic partial differential equation that can be used to describe the horizontal displacements of a vertical hanging chain with one end fixed and the other end free to move. Using a web camera and TRACKER software to record displacement data from a vibrating hanging chain, we verify a modified version…

  20. Realities of Supply Chain Collaboration

    NARCIS (Netherlands)

    Kampstra, R.P.; Ashayeri, J.; Gattorna, J.

    2006-01-01

    Successful supply chain collaboration (SCC) practices are rather exceptional, yet collaboration is believed to be the single most pressing need in supply chain management.In this paper we discuss the realities of SCC, present prerequisites for the collaboration process, indicate where the process

  1. Markov Chain Monte Carlo Methods

    Indian Academy of Sciences (India)

    Markov Chain Monte Carlo Methods. 2. The Markov Chain Case. K B Athreya, Mohan Delampady and T Krishnan. K B Athreya is a Professor at. Cornell University. His research interests include mathematical analysis, probability theory and its application and statistics. He enjoys writing for Resonance. His spare time is ...

  2. Financial value-chain analysis

    NARCIS (Netherlands)

    Duijn, van A.P.; Beukers, R.; Cowan, Roberta B.; Judge, L.O.; Pijl, van der Willem; Römgens, Indra; Scheele, Fleur; Steinweg, Tim

    2016-01-01

    This study is a detailed analysis of which parts of the tuna, shrimp, soy and beef supply chains are most open to constructive engagement through financial vehicles and mechanisms. The study indentifies the largest market shares in the various supply chains. For the retail sector, the objective was

  3. Adjustable chain trees for proteins

    DEFF Research Database (Denmark)

    Winter, Pawel; Fonseca, Rasmus

    2012-01-01

    A chain tree is a data structure for changing protein conformations. It enables very fast detection of clashes and free energy potential calculations. A modified version of chain trees that adjust themselves to the changing conformations of folding proteins is introduced. This results in much...

  4. Building an efficient supply chain.

    Science.gov (United States)

    Scalise, Dagmara

    2005-08-01

    Realizing at last that supply chain management can produce efficiencies and save costs, hospitals are beginning to adopt practices from other industries, such as the concept of extended supply chains, to improve product flow. They're also investing in enterprise planning resource software, radio frequency identification and other technologies, using quality data to drive standardization and streamlining processes.

  5. Managing the Global Supply Chain

    DEFF Research Database (Denmark)

    Hsuan, Juliana; Skjøtt-Larsen, Tage; Kinra, Aseem

    The world today faces global competition. The supply chain is vital part of the globalization process. Presenting a global view of the scope and complexity of supply chain management, this book reflects the rapid change that has taken place within the supply chain and its environment. This new...... well as current examples of best practice of managing supply chains in a global context....... edition has been fully updated with recent changes in concepts, technology and practice. Integration and collaboration are keywords in future competition. Firms must be agile and lean at the same time. The book gives an insightful overview of the conceptual foundations of the global supply chain, as...

  6. Managing the Global Supply Chain

    DEFF Research Database (Denmark)

    Skjøtt-Larsen, Tage; Schary, Philip B.; Mikkola, Juliana Hsuan

    The world today faces global competition. The supply chain is vital part of the globalization process. Presenting a global view of the scope and complexity of supply chain management, this book reflects the rapid change that has taken place within the supply chain and its environment. This new...... edition has been fully updated with recent changes in concepts, technology and practice. Integration and collaboration are keywords in future competition. Firms must be agile and lean at the same time. The book gives an insightful overview of the conceptual foundations of the global supply chain, as...... well as current examples of best practice of managing supply chains in a global context....

  7. Replicator dynamics in value chains

    DEFF Research Database (Denmark)

    Cantner, Uwe; Savin, Ivan; Vannuccini, Simone

    2016-01-01

    The pure model of replicator dynamics though providing important insights in the evolution of markets has not found much of empirical support. This paper extends the model to the case of firms vertically integrated in value chains. We show that i) by taking value chains into account, the replicator...... dynamics may revert its effect. In these regressive developments of market selection, firms with low fitness expand because of being integrated with highly fit partners, and the other way around; ii) allowing partner's switching within a value chain illustrates that periods of instability in the early...... stage of industry life-cycle may be the result of an 'optimization' of partners within a value chain providing a novel and simple explanation to the evidence discussed by Mazzucato (1998); iii) there are distinct differences in the contribution to market selection between the layers of a value chain...

  8. Managing the Global Supply Chain

    DEFF Research Database (Denmark)

    Skjøtt-Larsen, Tage; Schary, Philip B.; Mikkola, Juliana Hsuan

    edition has been fully updated with recent changes in concepts, technology and practice. Integration and collaboration are keywords in future competition. Firms must be agile and lean at the same time. The book gives an insightful overview of the conceptual foundations of the global supply chain, as......The world today faces global competition. The supply chain is vital part of the globalization process. Presenting a global view of the scope and complexity of supply chain management, this book reflects the rapid change that has taken place within the supply chain and its environment. This new...... well as current examples of best practice of managing supply chains in a global context....

  9. Environmental Management in Product Chains

    DEFF Research Database (Denmark)

    Jørgensen, Michael Søgaard; Forman, Marianne

    2009-01-01

    ). An overview of examples from our own research and from literature of the type and the role of environmental issues and initiatives in product chains (fourth section). A typology for characterizing corporate strategies as part of environmental management in product chains and characterizing those competencies......The chapter aims at giving background to companies, consultants, governmental regulators, NGOs etc. for the analysis and planning of environmental management in specific product chains through: A framework for understanding environmental management in product chains as shaped by the interaction...... between existing resources, norms and values and external pressures for environmental management (second section). A model for the types of corporate network relations that need to be mapped and understood in order to analyze and/or develop environmental management in a product chain (third section...

  10. Single homopolypeptide chains collapse into mechanically rigid conformations

    OpenAIRE

    Dougan, Lorna; Li, Jingyuan; Badilla, Carmen L.; Berne, B. J.; Fernandez, Julio M.

    2009-01-01

    Huntington's disease is linked to the insertion of glutamine (Q) in the protein huntingtin, resulting in polyglutamine (polyQ) expansions that self-associate to form aggregates. While polyQ aggregation has been the subject of intense study, a correspondingly thorough understanding of individual polyQ chains is lacking. Here we demonstrate a single molecule force-clamp technique that directly probes the mechanical properties of single polyQ chains. We have made polyQ constructs of varying leng...

  11. Logistics’ diagnostic in cosmetics and toiletries supply chain

    Directory of Open Access Journals (Sweden)

    Javier Arturo Orjuela-Castro

    2016-12-01

    Full Text Available The sector of cosmetics and toiletries is a world class sector, consolidated in Colombia with 690 companies of which 420 are in Bogotá D.C. Taking into account that logistics management generates competitive advantage in organizations as factor of success in a global economy, this paper proposes a logistics analysis applied to the case of cosmetics and toiletries supply chain. The results include the diagnosis of logistics processes and resources, which they were studied with an own methodology proposal. The methodology allowed study the logistics factors and variables, elements that recognized the logistical behaviour in the different links of the supply chain.

  12. Formation of liquid chain by collision of two laminar jets

    Science.gov (United States)

    Sanjay, Vatsal; Das, Arup Kumar

    2017-11-01

    The collision of liquid jets and formation of a sheet in the median plane are illustrated numerically. The sheet subsequently transforms into a chain-like fluidic structure with successive dwarf links in mutually orthogonal planes. To understand the behavior of fluid parcels inside the chain, flow kinematics are studied with streamlines and a self-similar velocity profile. For the generalization of chain profiles over a wide range of operating parameters, a correlation has been proposed based on numerical simulations and subsequent regression analyses. Citing the analogy between the impact of jets for the formation of elemental links and traversal of non-deformable fluid quanta after the collision, an attempt has been made to understand the fundamental physics of this phenomenon through force balance. The analogy helps us to take into account the role of surface tension and other forces on the shape and size of the liquid sheets. Further, the formation of higher order links is proposed as equivalent to the collision between the liquid rims bounding the sheet, modeled as the jets of reduced strengths and smaller impingement angles. Finally, we assess the effects of various fluid properties on the dimensions of these links, illustrating the viscous dissipation at the time of collisions.

  13. Autonomic dysfunction in a patient with X-linked adrenoleukodystrophy.

    Science.gov (United States)

    Zhang, Yifan; Guo, Dongmei; Tang, Yi

    2017-12-28

    X-linked adrenoleukodystrophy is an inherited disease caused by abnormal accumulation of very long chain fatty acids. The diagnosis of X-linked adrenoleukodystrophy can be confirmed with the mutation of ABCD1 gene. The main symptom of the X-linked adrenoleukodystrophy is spastic paraparesis, and autonomic dysfunction is rare in X-linked adrenoleukodystrophy. Here, we presented an X-ALD case of a 46-year-old Asian male with severe autonomic dysfunction. Impairment of the autonomic nervous system may closely relate to mitochondrial defect.

  14. Chains-into-Bins Processes

    Science.gov (United States)

    Batu, Tuğkan; Berenbrink, Petra; Cooper, Colin

    The study of balls-into-bins processes or occupancy problems has a long history. These processes can be used to translate realistic problems into mathematical ones in a natural way. In general, the goal of a balls-into-bins process is to allocate a set of independent objects (tasks, jobs, balls) to a set of resources (servers, bins, urns) and, thereby, to minimize the maximum load. In this paper, we analyze the maximum load for the chains-into-bins problem, which is defined as follows. There are n bins, and m objects to be allocated. Each object consists of balls connected into a chain of length ℓ, so that there are m ℓ balls in total. We assume the chains cannot be broken, and that the balls in one chain have to be allocated to ℓ consecutive bins. We allow each chain d independent and uniformly random bin choices for its starting position. The chain is allocated using the rule that the maximum load of any bin receiving a ball of that chain is minimized. We show that, for d ≥ 2 and m·ℓ= O(n), the maximum load is ((ln ln m)/ln d) + O(1) with probability 1-tilde O(1/m^{d-1}).

  15. Improving supply chain collaborations and performance of inefficient supply chain

    Directory of Open Access Journals (Sweden)

    M. Sanei

    2012-07-01

    Full Text Available Modern manufacturing enterprises are required to collaborate by their business partners through their business process operations such as design, manufacture, distribution, and aftersales services. And furthermore performance evaluation is of great importance for effective supply chain man agement. Therefore, DEA can help companies to remove some of the in efficiencies in operational processes in order to become more effective. The current paper develops one approach for determining the DEA projections for inefficient supply chains. Meanwhile this approach aims at providing an easy, efficient and more practical approach based on the performance evaluation for the multi-member supply chain. And ultimately, this model is illustrated by an numerical example of Chinese commercial bank, and case study application to provide of machine-making supply chain.

  16. Improving supply chain collaborations and performance of inefficient supply chain

    Directory of Open Access Journals (Sweden)

    M. Sanei

    2010-03-01

    Full Text Available Modern manufacturing enterprises are required to collaborate by their business partners through their business process operations such as design, manufacture, distribution, and aftersales services. And furthermore performance evaluation is of great importance for effective supply chain man agement. Therefore, DEA can help companies to remove some of the in efficiencies in operational processes in order to become more effective. The current paper develops one approach for determining the DEA projections for inefficient supply chains. Meanwhile this approach aims at providing an easy, efficient and more practical approach based on the performance evaluation for the multi-member supply chain. And ultimately, this model is illustrated by an numerical example of Chinese commercial bank, and case study application to provide of machine-making supply chain.

  17. A great start for the whole CERN accelerator chain

    CERN Multimedia

    2016-01-01

    With physics data-taking under way this week at the LHC, I’d like to take a look at what’s been happening at the rest of the CERN accelerator chain.   The LHC tends to dominate the news from CERN for all kinds of reasons, beech martens included, but we should not forget that there is a unique chain of accelerators upstream of the LHC, tended to and operated by an incredible group of people. If our whole accelerator chain does not work perfectly, nor can the LHC, and in addition to forming the LHC’s injector chain, our upstream accelerators support their own experiments, bringing great diversity to the CERN research programme. The chain begins with the proton source and Linac2, which have been faithfully delivering beams since 1978. This year, Linac2 accelerated its first beams on 29 February. Beams were then passed on to the PS Booster and the veteran PS, the linchpin of the CERN accelerator complex and in operation since 1959. The final link in the chain before the ...

  18. OPTIMAL SOLUTIONS FOR IMPLEMENTING THE SUPPLY-SALES CHAIN MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Elena COFAS

    2014-04-01

    Full Text Available The supply chain represents all physical flows , information and financial flows linking suppliers and customers. It leads on the one hand, the idea of the chain in which the various elements of an industrial production system are interrelated and secondly to a broad definition of supply (flow between plants, flow between a supplier and a customer, flow between two workstations etc.. For a number of enterprise managers, supply chain is a topic of major interest. In contrast, non-chain coordination, losses may result for the enterprise: obsolete inventory devaluation, impairment etc. Since the 1980’s, several companies came together in the same service all functions dealing logistic flow from supply to distribution, through production management and resource planning. At the same time it was developed the notion of “time" to expand these flows and to increase quality and reduce inventory. 1990’s promotes the trend of broadening the concept of integrated logistics to a more open organization, "supply chain" in which is contained the whole organization of the enterprise, designed around streams: sales, distribution, manufacturing, purchasing, and supply. This is the area where, through this work, I try to make a contribution towards finding practical solutions to implement an efficient supply chain that contribute to increased economic performance of companies.

  19. Closed loop supply chain network design with fuzzy tactical decisions

    Science.gov (United States)

    Sherafati, Mahtab; Bashiri, Mahdi

    2016-01-01

    One of the most strategic and the most significant decisions in supply chain management is reconfiguration of the structure and design of the supply chain network. In this paper, a closed loop supply chain network design model is presented to select the best tactical and strategic decision levels simultaneously considering the appropriate transportation mode in activated links. The strategic decisions are made for a long term; thus, it is more satisfactory and more appropriate when the decision variables are considered uncertain and fuzzy, because it is more flexible and near to the real world. This paper is the first research which considers fuzzy decision variables in the supply chain network design model. Moreover, in this study a new fuzzy optimization approach is proposed to solve a supply chain network design problem with fuzzy tactical decision variables. Finally, the proposed approach and model are verified using several numerical examples. The comparison of the results with other existing approaches confirms efficiency of the proposed approach. Moreover the results confirms that by considering the vagueness of tactical decisions some properties of the supply chain network will be improved.

  20. New sensors and processing chain

    CERN Document Server

    Yaakoubi, Nourdin

    2014-01-01

    A vital tool for researchers, engineers, and students, New Sensors and Processing Chain focuses on the processing chain to set up in order to extract relevant information on various systems. Highlighting the design of new microsensors and various applications, the authors present recent progress in instrumentation and microsystem design, providing insight to the modification of the sensor itself as well as its environment. Various applications illustrate the presentations, which show how a processing chain is organized from the data acquired by a specific sensor.

  1. Markov chains theory and applications

    CERN Document Server

    Sericola, Bruno

    2013-01-01

    Markov chains are a fundamental class of stochastic processes. They are widely used to solve problems in a large number of domains such as operational research, computer science, communication networks and manufacturing systems. The success of Markov chains is mainly due to their simplicity of use, the large number of available theoretical results and the quality of algorithms developed for the numerical evaluation of many metrics of interest.The author presents the theory of both discrete-time and continuous-time homogeneous Markov chains. He carefully examines the explosion phenomenon, the

  2. Model of contact between rollers and sprockets in chain-drive systems

    DEFF Research Database (Denmark)

    Pedersen, Sine Leergaard

    2005-01-01

    A model of a roller-chain drive is developed and applied to the simulation and analysis of roller-chain drives of large marine diesel engines. Two different ways of modelling the contact between the rollers and sprockets are presented; one using a circular shaped tooth profile and the other using...... the shape of a real tooth profile. The main components of the roller-chain drive model include the sprockets with different sizes and the chain made of rollers and links, which are represented by rigid bodies, mass particles and spring-damper assemblies, respectively. The contact between the rollers...

  3. Supply Chain Cyber-Resilience: Creating an Agenda for Future Research

    OpenAIRE

    Khan, Omera; Sepúlveda Estay, Daniel Alberto

    2015-01-01

    Supply chains have become more vulnerable in recent years, and high-profile cyber-attacks that have crippled the supply chains of well-known companies reveal that the point of entry for hackers is often through the weakest link in the chain. Exacerbated by growing complexity and the need to be visible, these supply chains share vital streams of information every minute of the day, thereby becoming an easy and highly lucrative target for talented criminals, causing financial losses as well as ...

  4. A Heuristic for Locating Electric Vehicle Charging Stations for Trip Chains

    DEFF Research Database (Denmark)

    Wen, Min; Røpke, Stefan

    We present the problem of locating a limited number of electric vehiclecharging stations for a given set of trip chains, each of which consistsof a series of linked short trips and is represented by a sequence ofintervening stops along the trip chain. The objective of this problemis to maximize t...... the number of trip chains that can be completed by the electric vehicle without running out of battery. A mixed-integer programmingformulation as well as a heuristic for solving this problemwill be presented.......We present the problem of locating a limited number of electric vehiclecharging stations for a given set of trip chains, each of which consistsof a series of linked short trips and is represented by a sequence ofintervening stops along the trip chain. The objective of this problemis to maximize...

  5. Structure of polymer chains under confinement

    Indian Academy of Sciences (India)

    Single chain form factor was observed both for bulk and confined chains using the condition of zero average contrast. Our measurements on neutral polymer chains are in agreement with the theoretical predictions established by Daoud and de Gennes for chains confined in a cylindrical pore when the chains are entangled ...

  6. Advances in Fluorescent Single-Chain Nanoparticles

    Directory of Open Access Journals (Sweden)

    Julen De-La-Cuesta

    2017-10-01

    Full Text Available Fluorophore molecules can be monitored by fluorescence spectroscopy and microscopy, which are highly useful and widely used techniques in cell biology, biochemistry, and medicine (e.g., biomarker analysis, immunoassays, cancer diagnosis. Several fluorescent micro- and nanoparticle systems based on block copolymer micelles and cross-linked polymer networks, quantum dots, π-conjugated polymers, and dendrimers have been evaluated as optical imaging systems. In this review, we highlight recent advances in the construction of fluorescent single-chain nanoparticles (SCNPs, which are valuable artificial soft nano-objects with a small tunable size (as small as 3 nm. In particular, the main methods currently available to endow SCNPs with fluorescent properties are discussed in detail, showing illustrative examples.

  7. Visualisierung von typisierten Links in Linked Data

    Directory of Open Access Journals (Sweden)

    Georg Neubauer

    2017-09-01

    Full Text Available Das Themengebiet der Arbeit behandelt Visualisierungen von typisierten Links in Linked Data. Die wissenschaftlichen Gebiete, die im Allgemeinen den Inhalt des Beitrags abgrenzen, sind das Semantic Web, das Web of Data und Informationsvisualisierung. Das Semantic Web, das von Tim Berners Lee 2001 erfunden wurde, stellt eine Erweiterung zum World Wide Web (Web 2.0 dar. Aktuelle Forschungen beziehen sich auf die Verknüpfbarkeit von Informationen im World Wide Web. Um es zu ermöglichen, solche Verbindungen wahrnehmen und verarbeiten zu können sind Visualisierungen die wichtigsten Anforderungen als Hauptteil der Datenverarbeitung. Im Zusammenhang mit dem Sematic Web werden Repräsentationen von zuhammenhängenden Informationen anhand von Graphen gehandhabt. Der Grund des Entstehens dieser Arbeit ist in erster Linie die Beschreibung der Gestaltung von Linked Data-Visualisierungskonzepten, deren Prinzipien im Rahmen einer theoretischen Annäherung eingeführt werden. Anhand des Kontexts führt eine schrittweise Erweiterung der Informationen mit dem Ziel, praktische Richtlinien anzubieten, zur Vernetzung dieser ausgearbeiteten Gestaltungsrichtlinien. Indem die Entwürfe zweier alternativer Visualisierungen einer standardisierten Webapplikation beschrieben werden, die Linked Data als Netzwerk visualisiert, konnte ein Test durchgeführt werden, der deren Kompatibilität zum Inhalt hatte. Der praktische Teil behandelt daher die Designphase, die Resultate, und zukünftige Anforderungen des Projektes, die durch die Testung ausgearbeitet wurden.

  8. Supply Chain Shipment Pricing Data

    Data.gov (United States)

    US Agency for International Development — This data set provides supply chain health commodity shipment and pricing data. Specifically, the data set identifies Antiretroviral (ARV) and HIV lab shipments to...

  9. Risikobasiertes Supply-Chain-Management

    DEFF Research Database (Denmark)

    Wieland, Andreas; Schinz, Philipp

    2015-01-01

    Das Management erlebt seit einigen Jahren dahingehend einen Paradigmenwechsel, dass nicht mehr Unternehmen als einzelne autonome Einheiten im Wettbewerb zueinander stehen, sondern die Supply Chains, in denen diese Unternehmen eingebunden sind. Ursachen hierfür sind beispielsweise die Auslagerung ...

  10. Relaxation Dynamics of Nanoparticle-Tethered Polymer Chains

    KAUST Repository

    Kim, Sung A

    2015-09-08

    © 2015 American Chemical Society. Relaxation dynamics of nanoparticle-tethered cis-1,4-polyisoprene (PI) are investigated using dielectric spectroscopy and rheometry. A model system composed of polymer chains densely grafted to spherical SiO2 nanoparticles to form self-suspended suspensions facilitates detailed studies of slow global chain and fast segmental mode dynamics under surface and geometrical confinement-from experiments performed in bulk materials. We report that unentangled polymer molecules tethered to nanoparticles relax far more slowly than their tethered entangled counterparts. Specifically, at fixed grafting density we find, counterintuitively, that increasing the tethered polymer molecular weight up to values close to the entanglement molecular weight speeds up chain relaxation dynamics. Decreasing the polymer grafting density for a fixed molecular weight has the opposite effect: it dramatically slows down chain relaxation, increases interchain coupling, and leads to a transition in rheological response from simple fluid behavior to viscoelastic fluid behavior for tethered PI chains that are unentangled by conventional measures. Increasing the measurement temperature produces an even stronger elastic response and speeds up molecular relaxation at a rate that decreases with grafting density and molecular weight. These observations are discussed in terms of chain confinement driven by crowding between particles and by the existence of an entropic attractive force produced by the space-filling constraint on individual chains in a self-suspended material. Our results indicate that the entropic force between densely grafted polymer molecules couples motions of individual chains in an analogous manner to reversible cross-links in associating polymers.

  11. The chain re-action

    CERN Multimedia

    2009-01-01

    On 18 March, beam commissioning started in the first ‘link’ of the accelerator chain – LINAC 2. This marks the start of what will be the longest period of beam operations in CERN’s history, with the accelerator complex remaining operational throughout the winter to supply the LHC. The Bulletin finds out what is being done to make sure the whole chain is ready for this historic run.

  12. CHALLENGES OF SUPPLY CHAIN MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Natalia GALANTON

    2017-11-01

    Full Text Available The present article highlights the basic characteristics of the supply chain, specific to changes in the business environment of companies at the beginning of the 21st century. Supply chain activities turn natural resources, raw materials and components into a finished product, which is then delivered to the final customer. The supply chain incorporates the production process alongside the raw material acquisition and distribution of finished products, encompassing all the existing process responsible for transforming the materials taken from the supplier to the finished products delivered to customers. Today, competitiveness and performance of an organization are dependent on belonging to an efficient and effective supply-delivery chain where synergies exist due to the establishment and implementation of common goals and strategies by partners. Competition does not take place between independent organizations or between small groups of organizations, but between supply and delivery chains, made up of interconnected networks of producers, distributors and logistics providers. Under these circumstances, supply chain managers must seek solutions to respond promptly to the most important challenges in the field.

  13. Reinforcement learning in supply chains.

    Science.gov (United States)

    Valluri, Annapurna; North, Michael J; Macal, Charles M

    2009-10-01

    Effective management of supply chains creates value and can strategically position companies. In practice, human beings have been found to be both surprisingly successful and disappointingly inept at managing supply chains. The related fields of cognitive psychology and artificial intelligence have postulated a variety of potential mechanisms to explain this behavior. One of the leading candidates is reinforcement learning. This paper applies agent-based modeling to investigate the comparative behavioral consequences of three simple reinforcement learning algorithms in a multi-stage supply chain. For the first time, our findings show that the specific algorithm that is employed can have dramatic effects on the results obtained. Reinforcement learning is found to be valuable in multi-stage supply chains with several learning agents, as independent agents can learn to coordinate their behavior. However, learning in multi-stage supply chains using these postulated approaches from cognitive psychology and artificial intelligence take extremely long time periods to achieve stability which raises questions about their ability to explain behavior in real supply chains. The fact that it takes thousands of periods for agents to learn in this simple multi-agent setting provides new evidence that real world decision makers are unlikely to be using strict reinforcement learning in practice.

  14. Linking open vocabularies

    CERN Document Server

    Greifender, Elke; Seadle, Michael

    2013-01-01

    Linked Data (LD), Linked Open Data (LOD) and generating a web of data, present the new knowledge sharing frontier. In a philosophical context, LD is an evolving environment that reflects humankinds' desire to understand the world by drawing on the latest technologies and capabilities of the time. LD, while seemingly a new phenomenon did not emerge overnight; rather it represents the natural progression by which knowledge structures are developed, used, and shared. Linked Open Vocabularies is a significant trajectory of LD. Linked Open Vocabularies targets vocabularies that have traditionally b

  15. Supply chain integration opportunities for the offshore wind industry

    DEFF Research Database (Denmark)

    Martinez, Ivan

    2016-01-01

    with means to overcome their current supply chain challenges. Design/methodology/approach - A comprehensive literature review was conducted involving 162 articles published in 29 peer-reviewed journals. The papers were analyzed in terms of the dimensions of SCI, research methodology, unit of analysis, level...... of analysis, type of industry and manufacturing environment being studied, integrative practices, integrative barriers and the link between SCI and performance. Findings - While SCI has been evolving to become an influential topic in the field of supply chain management, scholars have overlooked industrial......Purpose - This paper surveys the literature on supply chain integration (SCI) to identify the state of research in the various types of studied industries and manufacturing environments. The purpose of this paper is to identify academic discoveries that could provide offshore wind projects...

  16. The blackberry value chain in Caldas, Colombia: Impacts and benefits

    Directory of Open Access Journals (Sweden)

    Isaías Tobasura

    2013-10-01

    Full Text Available The value chain approach analyzes the overall performance of the subsystems including agricultural, industrial agro-industrial and commercial articulated to a particular production process. The cultivation of blackberry (Rubus glaucus Benth peculiar activities to farm production has grown in area and productivity in the department of Caldas. The article is a detailed follow-up on blackberry production in the municipalities of Aguadas, Aranzazu and Manzanares. The value chain was developed under government sponsored programs, whereby farmers are organized in village associations, as well as local and regional intermediaries, and few agroindustries that transform and distribute the production in the domestic market. The study shows a concentration of negative impacts and social benefits in the production link, and a concentration of economic benefits towards agribusiness in the transformation link.

  17. Demand chain management - The evolution

    Directory of Open Access Journals (Sweden)

    D Ericsson

    2011-06-01

    Full Text Available The concepts of Supply Chain Management (SCM and Demand Chain Management (DCM are among the new and debated topics concerning logistics in the literature. The question considered in this paper is: “Are these concepts needed or will they just add to the confusion?” Lasting business concepts have always evolved in close interaction between business and academia. Different approaches start out in business and they are then, more or less si- multaneously, aligned, integrated, systemised and structured in academia. In this way a terminology (or language is provided that helps in further diffusion of the concepts. There is a lack of consensus on the definition of the concept of SCM. This may be one of the major reasons for the difficulty in advancing the science and measuring the results of implementation in business. Relationships in SCM span from rather loose coalitions to highly structured virtual network integrations. DCM is a highly organised chain in which the key is mutual interdependence and partnership. The purpose is to create a distinctive competence for the chain as a whole that helps to identify and satisfy customer needs and wishes. The classical research concerning vertical marketing systems is very helpful in systemising the rather unstructured discussions in current SCM research. The trend lies in increasing competition between channels rather than between companies, which in turn leads to the creation of channels with a high degree of partnership and mutual interdependence between members. These types of channels are known as organised vertical marketing systems in the classic marketing channel research. The behaviour in these types of channels, as well as the formal and informal structures, roles in the network, power and dependence relations, etc. are well covered topics in the literature. The concept of vertical marketing systems lies behind the definition of demand chains and demand chain management proposed in this paper. A

  18. X-linked Adrenoleukodystrophy, The Tunisian Experience.

    Science.gov (United States)

    Nasrallah, Fahmi; Kraoua, Ichraf; Zidi, Wiem; Omar, Souheil; Sanhaji, Haifa; Feki, Moncef; Ben Youssef, Ilhem Turki; Kaabachi, Naziha

    2015-01-01

    X-linked adrenoleukodystrophy is a genetic disease affecting the degradation of very long chain fatty acids. This study aims to describe the clinical phenotype and biochemical feature of Tunisian patients; it also seeks to describe recognition of pattern analysis on the level of very long chain fatty acids in plasma for the visual discrimination of X-linked patients from a healthy group. During the last 21 years, 19 patients were diagnosed with X-linked adrenoleukodystrophy based on the clinical features combined with the area percentage of hexacosanoic acid (C26:0) as well as the ratio of C26:0 and lignoceric acid (C24:0) relative to behenic acid (C22:0) by gas chromatography. For the biochemical diagnosis of X-ALD with better accuracy, it has been desired to transform the numerical values of these biochemical markers into visually discriminating patterns. The clinical features of 19 patients aged between 4 to 47 years were classified into cerebral form (57.8%), adrenomyeloneuropathic (26.3%), and a few patients were asymptomatic. The ratio C24:0/C22:0 ranged from 1.12 to 2.41 (normal value: 0.46 - 0.9) and C26:0/C22:0 ratio ranged from 0.03 to 0.36 (normal value: 0.003 - 0.009). The concentration of fatty acids with 22 or more carbons in body fluid did not change with age in control subjects and patients. For the visual diagnostic of patients, the Scatter plot was a reliable method for the diagnostic patterns of very long chain fatty acids of patients with X-linked adrenoleukodystrophy disorders. The incidence of X-linked adrenoleukodystrophy disorders is under diagnosed in Tunisia. The diagnosis was confirmed by enzymatic activity study and molecular analysis but the analysis of very long chain fatty acids by gas chromatography remains a reliable tool for the diagnosis and early initiation of the treatment.

  19. Evolutionary Game Model Study of Construction Green Supply Chain Management under the Government Intervention

    Science.gov (United States)

    Xing, Yuanzhi; Deng, Xiaoyi

    2017-11-01

    The paper first has defined the concepts of green supply chain management and evolution game theory, and pointed out the characteristics of green supply chain management in construction. The main participants and key links of the construction green supply chain management are determined by constructing the organization framework. This paper established the evolutionary game model between construction enterprises and recycling enterprises for the green supply chain closed-loop structure. The waste recycling evolutionary stability equilibrium solution is obtained to explore the principle and effective scope of government policy intervention. This paper put forward the relevant countermeasures to the green supply chain management in construction recycling stage from the government point of view. The conclusion has reference value and guidance to the final product construction enterprises, recycling enterprises and the government during green supply chain.

  20. Strain-induced metal-semiconductor transition observed in atomic carbon chains.

    Science.gov (United States)

    La Torre, A; Botello-Mendez, A; Baaziz, W; Charlier, J-C; Banhart, F

    2015-03-30

    Carbyne, the sp(1)-hybridized phase of carbon, is still a missing link in the family of carbon allotropes. While the bulk phases of carbyne remain elusive, the elementary constituents, that is, linear chains of carbon atoms, have already been observed using the electron microscope. Isolated atomic chains are highly interesting one-dimensional conductors that have stimulated considerable theoretical work. Experimental information, however, is still very limited. Here we show electrical measurements and first-principles transport calculations on monoatomic carbon chains. When the 1D system is under strain, the chains are semiconducting corresponding to the polyyne structure with alternating bond lengths. Conversely, when the chain is unstrained, the ohmic behaviour of metallic cumulene with uniform bond lengths is observed. This confirms the recent prediction of a metal-insulator transition that is induced by strain. The key role of the contacting leads explains the rectifying behaviour measured in monoatomic carbon chains in a nonsymmetric contact configuration.

  1. Strain-induced metal–semiconductor transition observed in atomic carbon chains

    Science.gov (United States)

    La Torre, A.; Botello-Mendez, A.; Baaziz, W.; Charlier, J. -C.; Banhart, F.

    2015-01-01

    Carbyne, the sp1-hybridized phase of carbon, is still a missing link in the family of carbon allotropes. While the bulk phases of carbyne remain elusive, the elementary constituents, that is, linear chains of carbon atoms, have already been observed using the electron microscope. Isolated atomic chains are highly interesting one-dimensional conductors that have stimulated considerable theoretical work. Experimental information, however, is still very limited. Here we show electrical measurements and first-principles transport calculations on monoatomic carbon chains. When the 1D system is under strain, the chains are semiconducting corresponding to the polyyne structure with alternating bond lengths. Conversely, when the chain is unstrained, the ohmic behaviour of metallic cumulene with uniform bond lengths is observed. This confirms the recent prediction of a metal–insulator transition that is induced by strain. The key role of the contacting leads explains the rectifying behaviour measured in monoatomic carbon chains in a nonsymmetric contact configuration. PMID:25818506

  2. Let's "Downscale" Linked Data

    NARCIS (Netherlands)

    Gueret, C.D.M.; de Boer, V.; Schlobach, K.S.

    2014-01-01

    Open data policies and linked data publication are powerful tools for increasing transparency, participatory governance, and accountability. The linked data community proudly emphasizes the economic and societal impact such technology shows. But a closer look proves that the design and deployment of

  3. Let's "Downscale" Linked Data

    NARCIS (Netherlands)

    Gueret, Christophe; de Boer, Victor; Schlobach, Stefan

    2014-01-01

    Open data policies and linked data publication are powerful tools for increasing transparency, participatory governance, and accountability. A closer look at linked data technologies, however, proves that their design and deployment exclude the majority of the world’s population. It will take small

  4. Broken Links Tools

    Science.gov (United States)

    Some of these tools can be used on Drupal pages that are not published yet, or on non-Drupal content. Some, such as the Bookmarklet tools, can help make checking and correcting your links easier when used alongside Drupal's link reports.

  5. Refined Hopf Link Revisited

    CERN Document Server

    Iqbal, Amer

    2012-01-01

    We establish a relation between the refined Hopf link invariant and the S-matrix of the refined Chern-Simons theory. We show that the refined open string partition function corresponding to the Hopf link, calculated using the refined topological vertex, when expressed in the basis of Macdonald polynomials gives the S-matrix of the refined Chern-Simons theory.

  6. Demand Chain Management : Supply Chain Management + Orientasi Pasar

    OpenAIRE

    Mulyono, Fransisca

    2011-01-01

    In 1980s and 1990s decades supply chain is a popular term implemented in manybusiness firms in the world because of its capability to increasing operational costefficiency which lead to cheaper product price. In that time it is widely believed thatlower product price will yield the higher return in companies's profit, even in the longterm.As time goes by, it's grandeur become clearly faded : in the long term com-panies facing more loss because supply chain do not have a market orientation,an ...

  7. Supply Chain Management Practices in Toy Supply Chains

    DEFF Research Database (Denmark)

    Wong, Chee Yew; Arlbjørn, Jan Stentoft; Johansen, John

    2005-01-01

    Purpose - Innovative products usually experience highly unpredictable and variable demand. This is especially valid for the volatile and seasonal toy industry, which produces high obsolete inventory, lost sales and markdown. In such a volatile industry, what supply chain management (SCM) practices...... (traditional mass-production or push-models). These low-responsive practices in the toy supply chain are not caused only by slow knowledge diffusion. SCM know-how is not yet capable of managing such levels of volatility and seasonality. Therefore, explanations of these theoretical gaps and what new theories...

  8. Competitive behaviour in supply chains

    Directory of Open Access Journals (Sweden)

    Sylwia Konecka

    2014-06-01

    Full Text Available Background: The article deals with the results of literature and empirical research into competitiveness and behaviour of entities in supply chains. Methods: A research hypothesis has been formulated that both partnership as well as dominance relations occur between enterprises functioning as suppliers-consignees. In order to verify the hypothesis a survey was completed in 2012. It encompassed 116 enterprises (manufacturers - 33, service providers - 32 and sellers - 24 as well as enterprises selling goods and providing services - 27 of which 54 were large, 26 medium and 36 were small enterprises. Competitive behaviour in supply chains has been identified and analysed. Furthermore, the authors intended to identify, reveal and examine possible interdependences between competitive behaviour and behaviour typical of supply chain strategies. Results and conclusions: The analysis of survey results revealed a tendency to preserve equilibrium between a chain leader and dependent enterprises. It may be easily justified in practice as on the one hand there is a need to keep the supply chain competitive and on the other hand to avoid the interruptions, which could occur as a result of elimination of dependent enterprises.

  9. Multistable chain for ocean wave vibration energy harvesting

    Science.gov (United States)

    Harne, R. L.; Schoemaker, M. E.; Wang, K. W.

    2014-03-01

    The heaving of ocean waves is a largely untapped, renewable kinetic energy resource. Conversion of this energy into electrical power could integrate with solar technologies to provide for round-the-clock, portable, and mobile energy supplies usable in a wide variety of marine environments. However, the direct drive conversion methodology of gridintegrated wave energy converters does not efficiently scale down to smaller, portable architectures. This research develops an alternative power conversion approach to harness the extraordinarily large heaving displacements and long oscillation periods as an excitation source for an extendible vibration energy harvesting chain. Building upon related research findings and engineering insights, the proposed system joins together a series of dynamic cells through bistable interfaces. Individual impulse events are generated as the inertial mass of each cell is pulled across a region of negative stiffness to induce local snap through dynamics; the oscillating magnetic inertial mass then generates current in a coil which is connected to energy harvesting circuitry. It is shown that linking the cells into a chain transmits impulses through the system leading to cascades of vibration and enhancement of electrical energy conversion from each impulse event. This paper describes the development of the multistable chain and ways in which realistic design challenges were addressed. Numerical modeling and corresponding experiments demonstrate the response of the chain due to slow and large amplitude input motion. Lastly, experimental studies give evidence that energy conversion efficiency of the chain for wave energy conversion is much higher than using an equal number of cells without connections.

  10. Emulating Majorana fermions and their braiding by Ising spin chains

    Science.gov (United States)

    Backens, Stefan; Shnirman, Alexander; Makhlin, Yuriy; Gefen, Yuval; Mooij, Johan E.; Schön, Gerd

    2017-11-01

    We analyze the control of Majorana zero-energy states by mapping the fermionic system onto a chain of Ising spins. Although the topological protection is lost for the Ising system, the mapping provides additional insight into the nature of the quantum states. By controlling the local magnetic field, one can separate the Ising chain into ferromagnetic and paramagnetic phases, corresponding to topological and nontopological sections of the fermionic system. In this paper we propose (topologically nonprotected) protocols performing the braiding operation, and in fact also more general rotations. We first consider a T -junction geometry, but we also propose a protocol for a purely one-dimensional (1D) system. Both setups rely on an extra spin-1/2 coupler. By including the extra spin in the T -junction geometry, we overcome limitations due to the 1D character of the Jordan-Wigner transformation. In the 1D geometry the coupler, which controls one of the Ising links, should be manipulated once the ferromagnetic (topological) section of the chain is moved far away. We also propose experimental implementations of our scheme. One is based on a chain of flux qubits which allows for all needed control fields. We also describe how to translate our scheme for the 1D setup to a chain of superconducting wires hosting each a pair of Majorana edge states.

  11. Sterilizing elastomeric chains without losing mechanical properties. Is it possible?

    Directory of Open Access Journals (Sweden)

    Matheus Melo Pithon

    2015-06-01

    Full Text Available OBJECTIVE: To investigate the effects of different sterilization/disinfection methods on the mechanical properties of orthodontic elastomeric chains. METHODS: Segments of elastomeric chains with 5 links each were sent for sterilization by cobalt 60 (Co60 (20 KGy gamma ray technology. After the procedure, the elastomeric chains were contaminated with clinical samples of Streptococcus mutans. Subsequently, the elastomeric chains were submitted to sterilization/disinfection tests carried out by means of different methods, forming six study groups, as follows: Group 1 (control - without contamination, Group 2 (70°GL alcohol, Group 3 (autoclave, Group 4 (ultraviolet, Group 5 (peracetic acid and Group 6 (glutaraldehyde. After sterilization/disinfection, the effectiveness of these methods, by Colony forming units per mL (CFU/mL, and the mechanical properties of the material were assessed. Student's t-test was used to assess the number of CFUs while ANOVA and Tukey's test were used to assess elastic strength. RESULTS: Ultraviolet treatment was not completely effective for sterilization. No loss of mechanical properties occurred with the use of the different sterilization methods (p > 0.05. CONCLUSION: Biological control of elastomeric chains does not affect their mechanical properties.

  12. Decomposition of the Google pagerank and optimal linking strategy

    NARCIS (Netherlands)

    Avrachenkov, Konstatin; Litvak, Nelli

    2004-01-01

    We provide the analysis of the Google PageRank from the perspective of the Markov Chain Theory. First we study the Google PageRank for a Web that can be decomposed into several connected components which do not have any links to each other. We show that in order to determine the Google PageRank for

  13. Clinical manifest x-linked recessive adrenoleukodystrophy in a female

    DEFF Research Database (Denmark)

    Jack, Gyda Hlin Skuladottir; Malm-Willadsen, Karolina; Frederiksen, Anja

    2013-01-01

    Adrenoleukodystrophy (ALD) is a rare X-linked inherited leukodystrophy with a reduced capacity for degradation of very long chain fatty acids (VLCFAs). The intracellular accumulation of VLCFA leads to demyelination in the central nervous system (CNS) and cell destruction in the adrenal glands. ALD...

  14. Environmental management in product chains

    DEFF Research Database (Denmark)

    Jørgensen, Michael Søgaard; Forman, Marianne; Hansen, Anne Grethe

    of environmental initiatives, a number of recommendations for governmental regulation, which can support the further diffusion of environmental management in product chains, are developed. Furthermore, the report describes a number of theoretical perspectives from sociology of technology, organisation theory......This report presents the analyses of the shaping, implementation and embedding of eight types of environmental initiatives in product chains. The analyses focus on • the role of the type of product and branch, of the size of the companies and of governmental regulation • the focus...... of the environmental concerns and the reductions in environmental impact • organisational changes which have been part of the embedding of the initiatives The analyses are based on 25 cases from national and international product chains involving one or more Danish companies. Based on the analyses of the eight types...

  15. Markov chains and mixing times

    CERN Document Server

    Levin, David A

    2017-01-01

    Markov Chains and Mixing Times is a magical book, managing to be both friendly and deep. It gently introduces probabilistic techniques so that an outsider can follow. At the same time, it is the first book covering the geometric theory of Markov chains and has much that will be new to experts. It is certainly THE book that I will use to teach from. I recommend it to all comers, an amazing achievement. -Persi Diaconis, Mary V. Sunseri Professor of Statistics and Mathematics, Stanford University Mixing times are an active research topic within many fields from statistical physics to the theory of algorithms, as well as having intrinsic interest within mathematical probability and exploiting discrete analogs of important geometry concepts. The first edition became an instant classic, being accessible to advanced undergraduates and yet bringing readers close to current research frontiers. This second edition adds chapters on monotone chains, the exclusion process and hitting time parameters. Having both exercises...

  16. Who Manages Our Supply Chains?

    DEFF Research Database (Denmark)

    Flöthmann, Christoph

    While managers in traditional management functions focus on developing strong expertise to become “specialists” in their own discipline, supply chain managers are a different species: They have to combine a cross-functional understanding of various business fields and multi-faceted competencies...... to manage the manifold tasks they face on a daily basis. Unfortunately, as globalization has simultaneously increased the complexity of supply chains and the demand for highly qualified personnel, companies are facing a significant undersupply of talent (Cottrill, 2010). Moreover, organizations appear...... to lack understanding of supply chain personnel and how to support their recruitment, succession planning, and training and development (John, 2015). Surprisingly, at the same time, scientific research on that topic is relatively scarce. In response, the overarching purpose of this paper...

  17. Designing the Reverse Supply Chain

    DEFF Research Database (Denmark)

    Gobbi, Chiara

    2011-01-01

    for the reverse supply chain. Design/methodology/approach – In order to identify the relevance of the Fisher model, the model needs to be recast in terms of PRV, which, in this context, is considered the independent variable in the reverse logistics arena. Products defined as innovative in Fisher's taxonomy......Purpose – The purpose of this paper is to explore the impact of the product residual value (PRV) and the loss of value over time of returned products in the reverse supply chain configuration. It also examines whether or not the distinction of Fisher's functional and innovative products holds...... correspond to disposed products with high residual value, whereas functional products correspond to disposed products with low residual value. Furthermore, the PRV and the speed at which returned products lose their value are considered in order to determine the configuration of the reverse supply chain...

  18. Precise Nanoelectronics with Adatom Chains

    Science.gov (United States)

    Yamada, Toshishige

    1999-01-01

    Adatom chains on an atomically regulated substrate will be building components in future precise nanoelectronics. Adatoms need to be secured with chemical bonding, but then electronic isolation between the adatom and substrate systems is not guaranteed. A one-dimensional model shows that good isolation with existence of surface states is expected on an s-p crossing substrate such as Si, Ge, or GaAs, reflecting the bulk nature of the substrate. Isolation is better if adatoms are electronically similar to the substrate atoms, and can be manipulated by hydrogenation. Chain structures with group IV adatoms with two chemical bonds, or group III adatoms with one chemical bond, are semiconducting, reflecting the surface nature of the substrate. These structures are unintentionally doped due to the charge transfer across the chemical bonds. Physical properties of adatom chains have to be determined for the unified adatom-substrate system.

  19. X-linked adrenoleukodystrophy in women: a cross-sectional cohort study

    NARCIS (Netherlands)

    Engelen, Marc; Barbier, Mathieu; Dijkstra, Inge M. E.; Schür, Remmelt; de Bie, Rob M. A.; Verhamme, Camiel; Dijkgraaf, Marcel G. W.; Aubourg, Patrick A.; Wanders, Ronald J. A.; van Geel, Bjorn M.; de Visser, Marianne; Poll-The, Bwee T.; Kemp, Stephan

    2014-01-01

    X-linked adrenoleukodystrophy is the most common peroxisomal disorder. The disease is caused by mutations in the ABCD1 gene that encodes the peroxisomal transporter of very long-chain fatty acids. A defect in the ABCD1 protein results in elevated levels of very long-chain fatty acids in plasma and

  20. Tetanus Toxin Action : Inhibition of Neurotransmitter Release Linked to Synaptobrevin Proteolysis

    NARCIS (Netherlands)

    Link, Egenhard; Edelmann, Lambert; Chou, Judy H.; Binz, Thomas; Yamasaki, Shinji; Eisel, Uli; Baumert, Marion; Südhof, Thomas C.; Niemann, Heiner; Jahn, Reinhard

    1992-01-01

    Tetanus toxin is a potent neurotoxin that inhibits the release of neurotransmitters from presynaptic nerve endings. The mature toxin is composed of a heavy and a light chain that are linked via a disulfide bridge. After entry of tetanus toxin into the cytoplasm, the released light chain causes block

  1. OTULIN antagonizes LUBAC signaling by specifically hydrolyzing met1-linked polyubiquitin

    DEFF Research Database (Denmark)

    Keusekotten, K.; Elliott, P.R.; Kulathu, Y.

    2013-01-01

    The linear ubiquitin (Ub) chain assembly complex (LUBAC) is an E3 ligase that specifically assembles Met1-linked (also known as linear) Ub chains that regulate nuclear factor κB (NF-κB) signaling. Deubiquitinases (DUBs) are key regulators of Ub signaling, but a dedicated DUB for Met1 linkages has...

  2. Leading a supply chain turnaround.

    Science.gov (United States)

    Slone, Reuben E

    2004-10-01

    Just five years ago, salespeople at Whirlpool were in the habit of referring to their supply chain organization as the "sales disablers." Now the company excels at getting products to the right place at the right time--while managing to keep inventories low. How did that happen? In this first-person account, Reuben Slone, Whirlpool's vice president of Global Supply Chain, describes how he and his colleagues devised the right supply chain strategy, sold it internally, and implemented it. Slone insisted that the right focal point for the strategy was the satisfaction of consumers at the end of the supply chain. Most supply chain initiatives do the opposite: They start with the realities of a company's manufacturing base and proceed from there. Through a series of interviews with trade customers large and small, his team identified 27 different capabilities that drove industry perceptions of Whirlpool's performance. Knowing it was infeasible to aim for world-class performance across all of them, Slone weighed the costs of excelling at each and found the combination of initiatives that would provide overall competitive advantage. A highly disciplined project management office and broad training in project management were key to keeping work on budget and on benefit. Slone set an intense pace--three "releases" of new capabilities every month--that the group maintains to this day. Lest this seem like a technology story, however, Slone insists it is just as much a "talent renaissance." People are proud today to be part of Whirlpool's supply chain organization, and its new generation of talent will give the company a competitive advantage for years to come.

  3. Innovations in cold chain equipment for immunization supply chains.

    Science.gov (United States)

    Robertson, Joanie; Franzel, Lauren; Maire, Denis

    2017-04-19

    Since 2010, numerous new technologies have entered the immunization cold chain equipment market. The World Health Organization (WHO) Immunization Devices Programme-Performance, Quality and Safety (PQS)-has played a key role in bringing these to market. In this article, the authors explore the emergence of new cold chain equipment technologies from 2004 to 2016 and the role of PQS in this evolution. This review focuses on three major vaccine cold chain technology innovations-solar direct-drive refrigerators, long-term passive cold boxes, and equipment with user-independent freeze prevention. For the review, we used online data from WHO PQS, a literature search, and unpublished research reports. Timelines with key milestones in the emergence of the three focus technologies show delays of between one and three years between earliest field trials and publication of WHO specifications; procurement builds after the WHO prequalification of initial devices. The timelines show the role of PQS as both gatekeeper and enabler for cold chain equipment technologies. The use of target product profiles by PQS has increased its ability to signal preferred attributes and to engage with manufacturers during the product-development stage. Procurement data show how demand for solar direct-drive refrigerators increased over time. Gavi, the Vaccine Alliance, is employing demand-generation strategies to try to drive procurement of technologies with favorable technical attributes. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  4. Green supply chains: a new priority for supply chain managers

    CSIR Research Space (South Africa)

    Ittmann, H

    2011-01-01

    Full Text Available This article is not a comprehensive overview of green logistics. What it endeavours to do is to sensitise, in a very summarised way, those involved in logistics and supply chain management about the importance of green logistics and to highlight...

  5. Differential evolution Markov chain with snooker updater and fewer chains

    Energy Technology Data Exchange (ETDEWEB)

    Vrugt, Jasper A [Los Alamos National Laboratory; Ter Braak, Cajo J F [NON LANL

    2008-01-01

    Differential Evolution Markov Chain (DE-MC) is an adaptive MCMC algorithm, in which multiple chains are run in parallel. Standard DE-MC requires at least N=2d chains to be run in parallel, where d is the dimensionality of the posterior. This paper extends DE-MC with a snooker updater and shows by simulation and real examples that DE-MC can work for d up to 50--100 with fewer parallel chains (e.g. N=3) by exploiting information from their past by generating jumps from differences of pairs of past states. This approach extends the practical applicability of DE-MC and is shown to be about 5--26 times more efficient than the optimal Normal random walk Metropolis sampler for the 97.5% point of a variable from a 25--50 dimensional Student T{sub 3} distribution. In a nonlinear mixed effects model example the approach outperformed a block-updater geared to the specific features of the model.

  6. Implementing Sustainable Supply Chain Management

    DEFF Research Database (Denmark)

    Schulze, Heike; Bals, Lydia

    2017-01-01

    these in practice is much less understood. Purchasing & Supply Management (PSM) stands out as a function with particular influence on the global supply base. Thus, there is a central connection between SSCM implementation and PSM as a function. While the organizational level has usually been in focus of research......Implementing social and environmental dimensions in global supply chains remains a major challenge in practice. While processes and actions needed to implement sustainable supply chain management (SSCM) have been subject to more research in the last years, the question who implements...

  7. Markov chains and mixing times

    CERN Document Server

    Levin, David A; Wilmer, Elizabeth L

    2009-01-01

    This book is an introduction to the modern approach to the theory of Markov chains. The main goal of this approach is to determine the rate of convergence of a Markov chain to the stationary distribution as a function of the size and geometry of the state space. The authors develop the key tools for estimating convergence times, including coupling, strong stationary times, and spectral methods. Whenever possible, probabilistic methods are emphasized. The book includes many examples and provides brief introductions to some central models of statistical mechanics. Also provided are accounts of r

  8. Chain structure of cobra venom factor from Naja naja and Naja haje venom.

    Science.gov (United States)

    von Zabern, I; Przyklenk, H; Vogt, W

    1982-04-01

    The chain structure of cobra venom factor, whether isolated from Naja naja venom (CVFn) or from Naja Haje (CVFh) is similar. Both homologous proteins are composed of three disulphide-linked chains (A, B, and C) with apparent molecular weights of 72,000, 54,000, and 27,000-35,000 for CVFn and 68,000, 51,000 and 30,000-32,000 CVFh. That all three polypeptides are integral parts of CVF was demonstrated by investigation of the chain pattern after partial reduction. Reduction with 1-2 mM dithiothreitol under non-denaturing conditions yielded free B-chain, together with an intermediate product composed of disulphide-linked A- and C-chains. The C-chain was heterogenous when investigated by electrophoresis in polyacrylamide slab gels in the presence of SDS. Similarly, isoelectric focusing of CVFn and CVFh showed a multiplicity of bands in the pH range 5.2-6.4. Limited tryptic digestion resulted primarily in the fragmentation of the B-chain. CVFh is much more sensitive to tryptic attack than CVFn. In all our preparations of CVFh a partial, trypsin-like fragmentation of the B-chain was detectable to various extents.

  9. Chain and network science: A research framework

    NARCIS (Netherlands)

    Omta, S.W.F.; Trienekens, J.H.; Beers, G.

    2001-01-01

    In this first article of the Journal on Chain and Network Science the base-line is set for a discussion on contents and scope of chain and network theory. Chain and network research is clustered into four main ‘streams’: Network theory, social capital theory, supply chain management and business

  10. Met1-linked Ubiquitination in Immune Signalling

    DEFF Research Database (Denmark)

    Fiil, Berthe Katrine; Gyrd-Hansen, Mads

    2014-01-01

    identification of physiological substrates for Met1-Ub in response to activation of innate immune receptors. These discoveries have significantly advanced our understanding of how non-degradative ubiquitin modifications control pro-inflammatory responses mediated by nuclear factor κB and mitogen......Methionine 1-linked ubiquitin chains (Met1-Ub), or linear ubiquitin, has emerged as a central post-translational modification in innate immune signalling. Molecular machinery that assembles, senses and, more recently, disassembles Met1-Ub has been identified, and technical advances have enabled...

  11. Comparative International Air Cargo Solutions: The Pathway to a Resilient, Adaptable, Balanced and Sustainable Secure Global Air Cargo Supply Chain

    Science.gov (United States)

    2013-12-01

    counterfeit merchandise smugglers, and remains the weakest link in the air cargo transportation chain. The TSA and CBP continue to seek administrative...been exploited by narcotics, human and counterfeit merchandise smugglers for centuries, remains the weakest link in the air cargo transportation chain...have on the economies and industry concurrently. In 2011, air cargo merchandise transportation accounted for an estimated $424,265 million in U.S

  12. Link to paper

    Data.gov (United States)

    U.S. Environmental Protection Agency — Link to the paper. This dataset is associated with the following publication: Naile, J., A.W. Garrison, J. Avants, and J. Washington. Isomers/enantiomers of...

  13. Introduction to Reference Links

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Unlike most traditional metadata systems, the power of ServCat comes in relating a Reference to others. This module discusses the different types of links (aka...

  14. Link prediction on Twitter

    National Research Council Canada - National Science Library

    Sanda Martinčić-Ipšić; Edvin Močibob; Matjaž Perc

    2017-01-01

    .... Open access to information on Twitter makes it a valuable source of data for research on social interactions, sentiment analysis, content diffusion, link prediction, and the dynamics behind human...

  15. Management Accounting and Supply Chain Strategy

    OpenAIRE

    Hald, Kim S.; Thrane, Sof

    2016-01-01

    Research positioned in the intersection between management accounting and supply chain management is increasing. However, the relationship between management accounting and supply chain strategies has been neglected in extant research. This research adds to literature on management accounting and supply chain management through exploring how supply chain strategy and management accounting is related, and how supply chain relationship structure modifies this relation. Building on a contingency...

  16. Supply Chain Management In Construction Revealed

    Directory of Open Access Journals (Sweden)

    Dr. Ghaith Al-Werikat

    2015-08-01

    Full Text Available The construction supply chain plays a major role in the construction market competition. Construction supply chain management assists enterprises by helping to improve competitiveness increase profits and have more control over the different factors and variables within the project. This paper discusses the construction supply chain characteristics challenges and problems supply chains encounter and the benefits of an integrated supply chain in the construction sector.

  17. SUPPLY CHAIN MANAGEMENT – KEY FACTORS

    OpenAIRE

    Magdalena Daniela DINU

    2014-01-01

    This paper exposes Supply Chain Management by its key factors. Briefly, where the Supply Chain Management is treated as strategic part of a company then maintaining both control and influence throughout the entire supply chain are key factors and critical to success. On the other hand, finding the right partner to manage the non-strategic Supply Chains would be another key factor too. To define the most important key factors within Supply Chain Management means a deeply understanding of bot...

  18. Supply chain management and optimization in manufacturing

    CERN Document Server

    Pirim, Harun; Yilbas, Bekir Sami

    2014-01-01

    This book introduces general supply chain terminology particularly for novice readers, state of the art supply chain management and optimization issues and problems in manufacturing. The book provides insights for making supply chain decisions, planning and scheduling through supply chain network. It introduces optimization problems, i.e. transportation of raw materials, products and location, inventory of plants, warehouses and retailers, faced throughout the supply chain network.

  19. Information system for the supply chain management

    OpenAIRE

    Delia Adriana Marincas

    2008-01-01

    Supply chain management SCM is the integration and management of supply chain organizations and activities through collaboration, effective business processes and high levels of information sharing. The supply chain concept has become a concern due to global competition and increasing customer demand for value. Thus, the information must be available in real time across the supply chain and this can not be achieved without an integrated software system for supply chain management. Supply chai...

  20. STRUCTURAL IDENTIFICATION OF DISTINCT INVERSIONS OF PLANAR KINEMATIC CHAINS

    Directory of Open Access Journals (Sweden)

    Dr. Shubhashis Sanyal

    2011-12-01

    Full Text Available 0 0 1 171 979 International Islamic University 8 2 1148 14.0 Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Times New Roman";} Inversions are various structural possibilities of a kinematic chain. The number of inversions depends on the number of links of a kinematic chain. At the stage of structural synthesis, identification of distinct structural inversions of a particular type of kinematic chain is necessary. Various researchers have proposed methods for identification of distinct inversions. Present method based on Link joint connectivity is proposed to identify the distinct inversions of a planar kinematic chain. Method is tested successfully on single degree and multiple degree of freedom planar kinematic chains. ABSTRAK: Penyonsangan merupakan kebarangkalian pelbagai struktur suatu rangkaian kinematik. Jumlah songsangan bergantung kepada jumlah hubungan suatu rangkaian kinematik. Pada peringkat sintesis struktur, pengenalan songsangan struktur yang berbeza untuk suatu jenis rangkaian kinematik adalah perlu. Ramai penyelidik telah mencadangkan pelbagai kaedah pengenalan songsangan yang berbeza. Kaedah terkini berdasarkan hubungan kesambungan bersama telah dicadangkan untuk mengenalpasti songsangan yang berbeza dalam suatu satah rangkaian kinematik.

  1. KdV-Volterra chain

    Energy Technology Data Exchange (ETDEWEB)

    Pritula, G M; Vekslerchik, V E, E-mail: galinapritula@yandex.r, E-mail: vadym.vekslerchik@uclm.e [Institute for Radiophysics and Electronics, Kharkov (Ukraine)

    2010-09-10

    This paper is devoted to the system of coupled KdV-like equations. It is shown that this apparently non-integrable system possesses an integrable reduction which is closely related to the Volterra chain. This fact is used to construct the hyperelliptic solutions of the original system.

  2. Business Modeling - Supply Chain Management

    OpenAIRE

    Abdillah, Leon

    2017-01-01

    BM-SCM consists of: 1) Introduction, 2) Basic Concepts, 3) Inventory Management, 4) Forecasting Material, 5) Requirements, ) Transportation Management, 7) Vendor Management, 8) Warehouse Management, 9) Cross Docking, 10) Third Party Logistics (3PLs), 11) IT in Supply Chain, and 12) Presentations.

  3. Aggregation Methods in Food Chains.

    NARCIS (Netherlands)

    Kooi, B.W.; Poggiale, J.C.; Auger, P.

    1998-01-01

    The aim of this paper is to apply aggregation methods to food chains under batch and chemostat conditions. These predator-prey systems are modelled using ODEs, one for each trophic level. Because the models are based on mass conservation laws, they are conservative and this allows perfect

  4. Labour in Global Value Chains

    DEFF Research Database (Denmark)

    Lund-Thomsen, Peter; Nadvi, Khalid; Chan, Anita

    2012-01-01

    on the global football industry, a sector dominated by leading global brands that manage dispersed global value chains. It assesses the working conditions for football stitchers engaged in different forms of work organization, factories, stitching centres and home-based settings in Pakistan, India and China...

  5. Smallest Nanoelectronics with Adatom Chains

    Science.gov (United States)

    Yamada, Toshishige; Saini, Subhash (Technical Monitor)

    1998-01-01

    This viewgraph presentation is focused on the general aspect of atomic chain electronics that I have been studying. Results have been published before, but are being rederived here using a new physical/mathematical picture/model, which deepens the physical understanding. Precise adatom structures can be used as a template on a regulated surface with no uncertainty.

  6. Supply Chain Management: een overzicht

    NARCIS (Netherlands)

    Schuring, R.W.

    2012-01-01

    De laatste jaren wordt voor het managen van het netwerk van bedrijven die betrokken zijn bij het tot stand komen van producten of diensten het woord Supply Chain Management, ook wel SCM, gebruikt. SCM wordt als term vooral in grote industrieën gebruikt. Bijna ieder bedrijf heeft echter een

  7. Markov Chain Monte Carlo Methods

    Indian Academy of Sciences (India)

    Introduction. In parts 1 and 2 of this series it was shown how Markov chain Monte Carlo (MCMC) methods can be employed to obtain satisfactory approximations for integrals that are not easy to evaluate analytically. Such integrals arise routinely in statistical problems. Some of the statistical concepts that are relevant for the ...

  8. Transparency and value chain sustainability

    NARCIS (Netherlands)

    Mol, A.P.J.

    2015-01-01

    The rise of transparency on the public and political agendas is not an accident or fad, soon to be replaced by another timely topic in sustainability politics and governance. Transparency will remain a key topic in global value chains and will further develop as it piggy-backs on wider social

  9. Supply Chain Simulation : A Survey

    NARCIS (Netherlands)

    Kleijnen, J.P.C.

    2003-01-01

    This paper provides a survey of simulation in supply chain management.It reviews four types of simulation, namely spreadsheet simulation, system dynamics, discreteevent simulation, and business games.Which simulation type should be applied, depends on the type of managerial question to be answered

  10. Unreliability in Public Transport Chains

    NARCIS (Netherlands)

    Bruinsma, F.R.; Rietveld, P.; Vuuren, van D.J.

    1999-01-01

    In this paper the reliability of travelling by public transport modes is investigated. We deal with the reliability of travel times in public travel chains. Until now the only research in this field has been directed towards the reliability of trips where only one move is made. Therefore, a new

  11. Fatigue Damage of V-Lock Chain Ring Under Random Load

    Directory of Open Access Journals (Sweden)

    Zhang Qiang

    2016-10-01

    Full Text Available To study the influence of the random load on the V-lock chain ring for mining, the numerical simulation technology is used. The dynamic tension is obtained by using the dynamic model of the plough. The life and damage nephograms are obtained by using ANSYS Workbench. The analysis results show that the short fatigue life region of the V-lock chain ring for mining is mainly concentrated on the transition region between the medial straight edge and arc, and the fatigue damage of the link chain on the side of the motion direction of the plow head is larger than that on the other side. This link chain has strong anti-fatigue performance.

  12. Supply chain challenges. building relationships.

    Science.gov (United States)

    Beth, Scott; Burt, David N; Copacino, William; Gopal, Chris; Lee, Hau L; Lynch, Robert Porter; Morris, Sandra

    2003-07-01

    Supply chain management is all about software and systems, right? Put in the best technology, sit back, and watch as your processes run smoothly and the savings roll in? Apparently not. When HBR convened a panel of leading thinkers in the field of supply chain management, technology was not top of mind. People and relationships were the dominant issues of the day. The opportunities and problems created by globalization, for example, are requiring companies to establish relationships with new types of suppliers. The ever-present pressure for speed and cost containment is making it even more important to break down stubbornly high internal barriers and establish more effective cross-functional relationships. The costs of failure have never been higher. The leading supply chain performers are applying new technology, new innovations, and process thinking to far greater advantage than the laggards, reaping tremendous gains in all the variables that affect shareholder value: cost, customer service, asset productivity, and revenue generation. And the gap between the leaders and the losers is growing in almost every industry. This roundtable gathered many of the leading thinkers and doers in the field of supply chain management, including practitioners Scott Beth of Intuit, Sandra Morris of Intel, and Chris Gopal of Unisys. David Burt of the University of San Diego and Stanford's Hau Lee bring the latest research from academia. Accenture's William Copacino and the Warren Company's Robert Porter Lynch offer the consultant's perspectives. Together, they take a wide-ranging view of such topics as developing talent, the role of the chief executive, and the latest technologies, exploring both the tactical and the strategic in the current state of supply chain management.

  13. The Effects of Supply Chain Orientation, Supply Chain Management, and Collaboration on Perceived Firm Performance

    Science.gov (United States)

    2012-06-01

    Supply Chain : The Bullwhip Effect ,” Management Science, 43: 546-558 (1997). 33. Linkskold, Svenn. “Trust Development, the GRIT Proposal, and the...THE EFFECTS OF SUPPLY CHAIN ORIENTATION, SUPPLY CHAIN MANAGEMENT , AND...AFIT/ILS/ENS/12-06 THE EFFECTS OF SUPPLY CHAIN ORIENTATION, SUPPLY CHAIN MANAGEMENT , AND COLLABORATION ON

  14. chains

    Directory of Open Access Journals (Sweden)

    Gabriel Pérez-Salas

    2015-01-01

    Full Text Available Las barreras y aranceles al comercio exterior han disminuido significativamente gracias a los acuerdos multilaterales y los mecanismos de integración entre las naciones. Los costos logísticos representan una proporción significativa del precio final de los artículos, especialmente de los commodities. Por esta razón, minimizar los costos logísticos es un desafío importante para las naciones para fomentar la competitividad del comercio exterior y en particular para aprovechar la renta de los recursos naturales. En este artículo, proponemos un marco de referencia integral para la medición de costos logísticos, enfocado en determinar los extra-costos que resultan por procedimientos ineficientes y la falta de políticas públicas y regulaciones de las entidades públicas. Estos elementos no han sido considerados en la literatura, y este artículo aborda esta brecha. Como caso de estudio, presentamos la aplicación del marco de referencia para estimar los extra-costos en algunas cadenas logísticas de recursos naturales en Bolivia. Se presenta una discusión de los resultados encontrados, así como recomendaciones para trabajo futuro.

  15. Supply Chain Management Performance in Tourism. Continental Hotels Chain Case

    OpenAIRE

    Gabriela Ţigu; Bogdan Călăreţu

    2013-01-01

    With its origins in logistics, Supply Chain Management (SCM) concept is covering all managerial aspects of the flow of materials and information from source to customer, across the entire range of materials handling and movement functions, and throughout an organization and its supply channels. In tourism, these issues relate to the whole process of providing tourism services from sourcing of raw materials, products or different services) to supply and distribution, and SCM performance can ul...

  16. Research of STATCOM Impact on Wind Farm LVRT and Protection

    OpenAIRE

    YI Hai-dong; YUAN Tie-jiang; CHAO Qin; YANG Bai-jie

    2012-01-01

    Because of the wind turbine which possesses low voltage ride through (LVRT) capability can keep on working during the system fault, greatly reduce the adverse effects of power grid and ensure the relay protection reliability. However, the asynchronous wind turbine which widely used in home and abroad doesn’t have enough LVRT capability. So this paper proposes a method to enhance the LVRT capability of fixed speed induction generator (FSIG) based on wind farm using static synchronous compensat...

  17. KNOWNET: Exploring Interactive Knowledge Networking across Insurance Supply Chains

    Directory of Open Access Journals (Sweden)

    Susan Grant

    2014-01-01

    Full Text Available Social media has become an extremely powerful phenomenon with millions of users who post status updates, blog, links and pictures on social networking sites such as Facebook, LinkedIn, and Twitter. However, social networking has so far spread mainly among consumers. Businesses are only now beginning to acknowledge the benefits of using social media to enhance employee and supplier collaboration to support new ideas and innovation through knowledge sharing across functions and organizational boundaries. Many businesses are still trying to understand the various implications of integrating internal communication systems with social media tools and private collaboration and networking platforms. Indeed, a current issue in organizations today is to explore the value of social media mechanisms across a range of functions within their organizations and across their supply chains.The KNOWNET project (an EC funded Marie Curie IAPP seeks to assess the value of social networking for knowledge exchange across Insurance supply chains. A key objective of the project being to develop and build a web based interactive environment - a Supplier Social Network or SSN, to support and facilitate exchange of good ideas, insights, knowledge, innovations etc across a diverse group of suppliers within a multi level supply chain within the Insurance sector.

  18. Selected Aspects Of The Risk In The Supply Chain In Context Of The Supplier Quality Management

    Science.gov (United States)

    Koblen, Ivan; Lestyánszka Škůrková, Katarína

    2015-06-01

    The introductory part of the paper underlines the importance of "Risk-based thinking" in the Quality Management System (QMS) and risk in the supply chain, as a principle part of the QMS. After introducing the key terms, the authors focused on the principle part of the article - explanation of the external and internal supply chain risks and the main factors concerning the supply risks, demand risks and environmental risks (as cardinal types of external supply chain risks) as well as the manufacturing and process risks, network/planning and control risks (as most important types of internal supply chain risks). The authors inform on the selected supply chain risk management tools, especially on those which are linked to the appropriate utilization of quality management tools.

  19. Selected Aspects Of The Risk In The Supply Chain In Context Of The Supplier Quality Management

    Directory of Open Access Journals (Sweden)

    Koblen Ivan

    2015-06-01

    Full Text Available The introductory part of the paper underlines the importance of "Risk-based thinking" in the Quality Management System (QMS and risk in the supply chain, as a principle part of the QMS. After introducing the key terms, the authors focused on the principle part of the article - explanation of the external and internal supply chain risks and the main factors concerning the supply risks, demand risks and environmental risks (as cardinal types of external supply chain risks as well as the manufacturing and process risks, network/planning and control risks (as most important types of internal supply chain risks. The authors inform on the selected supply chain risk management tools, especially on those which are linked to the appropriate utilization of quality management tools.

  20. Drugs + HIV, Learn the Link

    Medline Plus

    Full Text Available ... Education Projects » Learn the Link - Drugs and HIV Learn the Link - Drugs and HIV Email Facebook Twitter ... research findings and news updates. Read on to Learn the Link between drug use and HIV and ...

  1. Towards biotracing in food chains

    DEFF Research Database (Denmark)

    Hoorfar, Jeffrey; Wagner, Martin; Jordan, Kieran

    2011-01-01

    , and 21 cross-disciplinary work packages that cover tracing and tracking of contamination in feed, meat and dairy chains, in addition to accidental and deliberate contamination of bottled water. The BIOTRACER Consortium consists of 46 partners, including Europe's largest food/feed industries, several SMEs......Biotracing is tracing (backward)/tracking (forward) biological contamination in the food/feed chain. Advances in detection technologies, improvements in molecular marker identification, clearer understanding of pathogenicity markers, improved modelling methodologies and, more importantly...... but developing tools that can be used in “second-generation” risk assessments involving quantitative microbiology. This concept is the core activity of BIOTRACER, which is an Integrated Project (2007–2011) funded by the EU 6th Framework Programme. The research in biotracing is organised into five Research Areas...

  2. Phase transitions in Ising Chains?

    Science.gov (United States)

    Mancini, Ferdinando

    2009-12-01

    An open question in the study of the spin-1/2 Ising model is the solution of the two-dimensional case in the presence of a magnetic field. A possible answer is based on the study of L-coupled linear chains in the limit of large L. Results reported in the literature show that a dimensional crossover from the one to the two dimensional model does not exist. However, what happens if one considers open boundary conditions (BC)? In this article I show that, for an appropriate choice of the BC, a system of L-chains exhibits a ferromagnetic order characterized by a critical temperature which, for zero magnetic field, tends to the Onsager's one as L increases. It is then possible to study the phase diagram in the (h, T) plane and obtain a solution for finite magnetic field.

  3. The Supply Chain Triangle: How Synchronisation, Stability, and Productivity of Material Flows Interact

    Directory of Open Access Journals (Sweden)

    Florian Klug

    2013-01-01

    Full Text Available Empirical evidence created a commonly accepted understanding that synchronisation and stability of material flows impact its productivity. This crucial link between synchronous and stable material flows by time and quantity to create a supply chain with the highest throughput rates is at the heart of lean thinking. Although this supply chain triangle has generally been acknowledged over many years, it is necessary to reach a finer understanding of these dynamics. Therefore, we will develop and study supply chains with the help of fluid dynamics. A multistage, continuous material flow is modelled through a conservation law for material density. Unlike similar approaches, our model is not based on some quasi steady-state assumptions about the stochastic behaviour of the involved supply chain but rather on a simple deterministic rule for material flow density. These models allow us to take into account the nonlinear, dynamical interactions of different supply chain echelons and to test synchronised and stable flow with respect to its potential impacts. Numerical simulations verify that the model is able to simulate transient supply chain phenomena. Moreover, a quantification method relating to the fundamental link between synchronisation, stability, and productivity of supply chains has been found.

  4. Quadratic Variation by Markov Chains

    DEFF Research Database (Denmark)

    Hansen, Peter Reinhard; Horel, Guillaume

    We introduce a novel estimator of the quadratic variation that is based on the the- ory of Markov chains. The estimator is motivated by some general results concerning filtering contaminated semimartingales. Specifically, we show that filtering can in prin- ciple remove the effects of market......- cal results. The proposed estimator is consistent with a Gaussian limit distribution and we study its properties in simulations and an empirical application....

  5. Validation Chain for ATM Concepts

    OpenAIRE

    Roeder, Michael; Biella, Marcus; Kaltenhäuser, Sven

    2015-01-01

    Validation Chain for ATM Concepts on the example of large scale Airport projects. Examples of FP4-FP6 and SESAR are pointing out the necessary loop from Fast Time Simulations (FTS) over Real Time Simulations (RTS) as preparation for on site trials (OST). This presentation also focuses on the difference between verification and validation following the European Operational Concept Validation Methodology (E-OCVM).

  6. ARCHITECTURAL CONCEPTS FOR VALUE CHAINS

    Directory of Open Access Journals (Sweden)

    A.C. Janse van Rensburg

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT:The Porter Value Chain has been widely adopted by the business community as a mechanism to understand and comprehend complexity in business environments, with the ultimate goal of structuring the business to maximize its competitive advantage. Implementing the Value Chain is not easy: a number of organizations can testify to their failure to derive any benefits at all from this concept. To overcome this problem, an approach is presented to assist the organization in creating a Value Chain reference model within the broader context of the organization’s enterprise architecture.

    AFRIKAANSE OPSOMMING: Die “Porter Waardeketting” is ’n algemene aanvaarde praktyk wat deur maatskappye gebruik word om die kompleksiteit van besigheidsomgewings mee te verstaan. Die uiteindelike doel hiervan is om die besigheid se mededings voordele te optimiseer. Om die Waardekettingkonsep te implementeer, is nie ’n maklike taak nie – verskeie organisasies kan getuig van mislukte implementeringspogings. Hierdie artikel beskryf ’n benadering beskryf wat gebruik kan word om die organisasie te help om ’n Waardekettingmodel te skep in die bree konteks van die organisasie se besigheidsargitektuur.

  7. High molecular weight forms of mammalian respiratory chain complex II.

    Directory of Open Access Journals (Sweden)

    Nikola Kovářová

    Full Text Available Mitochondrial respiratory chain is organised into supramolecular structures that can be preserved in mild detergent solubilisates and resolved by native electrophoretic systems. Supercomplexes of respiratory complexes I, III and IV as well as multimeric forms of ATP synthase are well established. However, the involvement of complex II, linking respiratory chain with tricarboxylic acid cycle, in mitochondrial supercomplexes is questionable. Here we show that digitonin-solubilised complex II quantitatively forms high molecular weight structures (CIIhmw that can be resolved by clear native electrophoresis. CIIhmw structures are enzymatically active and differ in electrophoretic mobility between tissues (500 - over 1000 kDa and cultured cells (400-670 kDa. While their formation is unaffected by isolated defects in other respiratory chain complexes, they are destabilised in mtDNA-depleted, rho0 cells. Molecular interactions responsible for the assembly of CIIhmw are rather weak with the complexes being more stable in tissues than in cultured cells. While electrophoretic studies and immunoprecipitation experiments of CIIhmw do not indicate specific interactions with the respiratory chain complexes I, III or IV or enzymes of the tricarboxylic acid cycle, they point out to a specific interaction between CII and ATP synthase.

  8. On the collision of laminar jets: fluid chains and fishbones

    Science.gov (United States)

    Bush, John W. M.; Hasha, Alexander E.

    2004-07-01

    We present the results of a combined experimental and theoretical investigation of the family of free-surface flows generated by obliquely colliding laminar jets. We present a parameter study of the flow, and describe the rich variety of forms observed. When the jet Reynolds number is sufficiently high, the jet collision generates a thin fluid sheet that evolves under the combined influence of surface tension and fluid inertia. The resulting flow may take the form of a fluid chain: a succession of mutually orthogonal links, each composed of a thin oval film bound by relatively thick fluid rims. The dependence of the form of the fluid chains on the governing parameters is examined experimentally. An accompanying theoretical model describing the form of a fluid sheet bound by stable rims is found to yield good agreement with the observed chain shapes. In another parameter regime, the fluid chain structure becomes unstable, giving rise to a striking new flow structure resembling fluid fishbones. The fishbones are demonstrated to be the result of a Rayleigh Plateau instability of the sheet's bounding rims being amplified by the centripetal force associated with the flow along the curved rims.

  9. An analysis of Science and Technology indicator by stages in the petroleum production chain; Analise de indicador de C e T nos elos da cadeia produtiva petrolifera

    Energy Technology Data Exchange (ETDEWEB)

    Martini, Ana Amelia M.G.; Antunes, Adelaide M.S. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica. Programa de Pos-Graduacao em Processos Quimicos e Bioquimicos

    2004-07-01

    Taking into account the global importance of the petroleum industry, the present work aims to present a study of this industry through the lens of its production chain, using bibliometric indicators of technological innovation in order to determine critical competitiveness factors. The concept of the production chain includes the set of activities undertaken progressively from raw material to the final product, including distribution and sales, with each segment being a link in the chain. The petroleum industry is composed of a production chain which may be divided into the following segments: exploration and production, transportation of crude oil and natural gas, refining, transportation of derivatives and distribution. The development of the present work involved the analysis of information about the petroleum production chain in Brazil and elsewhere, gathered through research in specialized database. The analysis of bibliometric indicators of technological innovation in each link of the production chain maps the technological trends existing in this chain. (author)

  10. Coordinated supply chain dynamic production planning model

    Science.gov (United States)

    Chandra, Charu; Grabis, Janis

    2001-10-01

    Coordination of different and often contradicting interests of individual supply chain members is one of the important issues in supply chain management because the individual members can not succeed without success of the supply chain and vice versa. This paper investigates a supply chain dynamic production planning problem with emphasis on coordination. A planning problem is formally described using a supply chain kernel, which defines supply chain configuration, management policies, available resources and objectives both at supply chain or macro and supply chain member or micro levels. The coordinated model is solved in order to balance decisions made at the macro and micro levels and members' profitability is used as the coordination criterion. The coordinated model is used to determine inventory levels and production capacity across the supply chain. Application of the coordinated model distributes costs burden uniformly among supply chain members and preserves overall efficiency of the supply chain. Influence of the demand series uncertainty is investigated. The production planning model is a part of the integrated supply chain decision modeling system, which is shared among the supply chain members across the Internet.

  11. enzyme-linked

    African Journals Online (AJOL)

    SA MEDIESE TYDSKRIF DEEL 63 29 JANUARIE 1983. B surface antigen in donated screening and confirmation by immunosorbent assay. Hepatitis blood - enzyme-linked. M. O. BUBB, T. ... weeks at weekly intervals. After 6 weeks test blood samples were ... This assay normally takes 3 hours. Results. Fig. 1. Frequency ...

  12. Response model parameter linking

    NARCIS (Netherlands)

    Barrett, M.L.D.

    2015-01-01

    With a few exceptions, the problem of linking item response model parameters from different item calibrations has been conceptualized as an instance of the problem of equating observed scores on different test forms. This thesis argues, however, that the use of item response models does not require

  13. Australian Curriculum Linked Lessons

    Science.gov (United States)

    Hurrell, Derek; O'Neil, Jennifer

    2011-01-01

    In providing a continued focus on tasks and activities that help to illustrate key ideas embedded in the new Australian Curriculum, this issue the authors focus, on Geometry in the Measurement and Geometry strand with strong links for an integrated focus on the Statistics and Probability strand. The small unit of work on the sorting and…

  14. Linking Literacy and Movement

    Science.gov (United States)

    Pica, Rae

    2010-01-01

    There are many links between literacy and movement. Movement and language are both forms of communication and self-expression. Rhythm is an essential component of both language and movement. While people may think of rhythm primarily in musical terms, there is a rhythm to words and sentences as well. Individuals develop an internal rhythm when…

  15. Linking place and mind

    DEFF Research Database (Denmark)

    Jensen, Marie Møller

    2016-01-01

    This paper investigates the salience of vernacular Tyneside forms on the basis of theories of enregisterment and exemplar processing. On one level, exemplar theory provides a psycholinguistic account of how the link between social value and linguistic features is possible. Conversely, integrating...

  16. TWSTFT Link Calibration Report

    Science.gov (United States)

    2015-09-01

    Washington Headquarters Services , Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington VA 22202-4302...and Bauch A (2014) THE EUROPEAN TW CALIBRATION CAMPAIGN 2014 IN THE SCOPE OF GALILEO (TGVF- FOC), An opportunity to update, TW link calibrations in

  17. Mass spectrometric method to determine the chain length of oligosaccharides attached to phenolic polymers by nonglycosidic linkages

    Science.gov (United States)

    James L. Minor; Roger C. Pettersen

    1987-01-01

    In many plants, a portion of the polysaccharides appears to have a very low degree of cross-linking with aromatic polymers such as lignin or flavolans. The proportion of cross-linked units may be enriched for study by enzymatically hydrolyzing the nonbonded carbohydrates. A convenient method is described for the simultaneous analysis of sugar content and apparent chain...

  18. Isolated Tracklet Linking

    Science.gov (United States)

    Weryk, Robert J.; Wainscoat, Richard J.; Williams, Gareth

    2017-10-01

    We discuss our on-going work to reduce the size of the Isolated Tracklet File (ITF) : a database hosted by the Minor Planet Center (MPC) containing 14+ million unlinked detections of asteroids. The ITF is dominated by observations from Pan-STARRS1 (F51), the Catalina Sky Survey (G96), and the Spacewatch Project (691).Survey telescopes are dependent on the follow-up capabilities of other telescopes, but many of their detected objects are not linked to already known objects, are are either not posted to the NEO Confirmation Page and/or are not followed up sufficiently, and therefore have their astrometry relegated to the ITF. While many of these asteroids may have in fact been previously observed sufficiently over longer timescales (enough to become designated objects), the linking of their astrometry can pose a challenge.We have developed a search method capable of finding and linking these isolated detections for distinct types of orbit classes, including main-belt and Hungaria objects (which often appear on the NEOCP due to their apparent motion). We use a brute-force technique which compares tracklets having motion which suggests they are the same object. Suspected linkages are further tested by searching for additional tracklets over multiple oppositions.So far, we have linked a significant portion of the ITF and have submitted these linkages to the MPC. We are confident in being able to link even more tracklets. Our method can even associate these new linkages with already designated objects, which will eventually lead to them becoming numbered objects. We hope to improve the efficiency of all asteroid surveys as future detections can be batch submitted without manual review, and more objects which are well known will not be posted to the NEOCP.

  19. Ions for LHC: performance of the injector chain

    CERN Document Server

    Manglunki, D; Baudrenghien, P; Bellodi, G; Blas, A; Bohl, T; Carli, C; Carlier, E; Cettour Cave, S; Chanel, M; Cornelis, K; Damerau, H; Findlay, A; Gilardoni, S; Hancock, S; Jowett, JM; Küchler, D; Maury, S; Métral, E; Pasinelli, S; Schokker, M; Tranquille, G; Vandorpe, B; Wenninger, J; Wehrle, U

    2011-01-01

    The first LHC Pb ion run took place at 1.38 A TeV/c per beam in autumn 2010. After a short period of runningin, the injector chain was able to fill the collider with up to 137 bunches per ring, with an intensity of 108 Pb82+ ions/bunch, about 50% higher than the design value. This yielded a luminosity of 3×1025 Hz/cm2, allowing the experiments to accumulate just under 10 b-1 each during the four week run. We review the performance of the individual links of the injector chain, and address the main issues limiting the LHC luminosity, in view of reaching 1026 Hz/cm2 in 2011, and substantially beyond when the LHC energy increases after the long shutdown in 2013-14.

  20. Mechanics and statistics of the worm-like chain

    Science.gov (United States)

    Marantan, Andrew; Mahadevan, L.

    2018-02-01

    The worm-like chain model is a simple continuum model for the statistical mechanics of a flexible polymer subject to an external force. We offer a tutorial introduction to it using three approaches. First, we use a mesoscopic view, treating a long polymer (in two dimensions) as though it were made of many groups of correlated links or "clinks," allowing us to calculate its average extension as a function of the external force via scaling arguments. We then provide a standard statistical mechanics approach, obtaining the average extension by two different means: the equipartition theorem and the partition function. Finally, we work in a probabilistic framework, taking advantage of the Gaussian properties of the chain in the large-force limit to improve upon the previous calculations of the average extension.

  1. Role of special cross-links in structure formation of bacterial DNA polymer

    Science.gov (United States)

    Agarwal, Tejal; Manjunath, G. P.; Habib, Farhat; Lakshmi Vaddavalli, Pavana; Chatterji, Apratim

    2018-01-01

    Using data from contact maps of the DNA-polymer of Escherichia coli (E. Coli) (at kilobase pair resolution) as an input to our model, we introduce cross-links between monomers in a bead-spring model of a ring polymer at very specific points along the chain. Via suitable Monte Carlo simulations, we show that the presence of these cross-links leads to a particular organization of the chain at large (micron) length scales of the DNA. We also investigate the structure of a ring polymer with an equal number of cross-links at random positions along the chain. We find that though the polymer does get organized at the large length scales, the nature of the organization is quite different from the organization observed with cross-links at specific biologically determined positions. We used the contact map of E. Coli bacteria which has around 4.6 million base pairs in a single circular chromosome. In our coarse-grained flexible ring polymer model, we used 4642 monomer beads and observed that around 80 cross-links are enough to induce the large-scale organization of the molecule accounting for statistical fluctuations caused by thermal energy. The length of a DNA chain even of a simple bacterial cell such as E. Coli is much longer than typical proteins, hence we avoided methods used to tackle protein folding problems. We define new suitable quantities to identify the large scale structure of a polymer chain with a few cross-links.

  2. Supply chain strategies, issues and models

    CERN Document Server

    Ramanathan, Ramakrishnan

    2014-01-01

    In the 21st century, supply chain operations and relationships among supply chain partners have become highly challenging, necessitating new approaches, e.g., the development of new models. Supply Chain Strategies, Issues and Models discusses supply chain issues and models with examples from actual industrial cases. Expert authors with a wide spectrum of knowledge working in various areas of supply chain management from various geographical locations offer refreshing, novel and insightful ideas and address possible solutions using established theories and models. Supply Chain Strategies, Issues and Models features studies that have used mathematical modeling, statistical analyses and also descriptive qualitative studies. The chapters cover many relevant themes related to supply chains and logistics including supply chain complexity, information sharing, quality (six sigma), electronic Kanbans, inventory models, scheduling, purchasing and contracts. To facilitate easy reading, the chapters that deal with suppl...

  3. Information flow in the pharmaceutical supply chain.

    Science.gov (United States)

    Yousefi, Nazila; Alibabaei, Ahmad

    2015-01-01

    Managing the supply chain plays an important role in creating competitive advantages for companies. Adequate information flow in supply chain is one of the most important issues in SCM. Therefore, using certain Information Systems can have a significant role in managing and integrating data and information within the supply chain. Pharmaceutical supply chain is more complex than many other supply chains, in the sense that it can affect social and political perspectives. On the other hand, managing the pharmaceutical supply chain is difficult because of its complexity and also government regulations in this field. Although, Iran has progressed a lot in pharmaceutical manufacturing, still there are many unsolved issues in managing the information flow in the pharmaceutical supply chain. In this study, we reviewed the benefits of using different levels of an integrated information system in the supply chain and the possible challenges ahead.

  4. SUPPLY CHAIN MANAGEMENT – KEY FACTORS

    Directory of Open Access Journals (Sweden)

    Magdalena Daniela DINU

    2014-06-01

    Full Text Available This paper exposes Supply Chain Management by its key factors. Briefly, where the Supply Chain Management is treated as strategic part of a company then maintaining both control and influence throughout the entire supply chain are key factors and critical to success. On the other hand, finding the right partner to manage the non-strategic Supply Chains would be another key factor too. To define the most important key factors within Supply Chain Management means a deeply understanding of both Supply Chain’ s components, procedures, workflow, processes and the importance of Supply Chain Management into maximizing company's value. SCORE model able to provide solid information about measuring performance and identifying priorities within Supply Chain Management will help us to understand the key factors by analyzing its elements: Plan, Source, Make, Deliver,Return, Enable. These elements covers all the challenging areas from first to third tier of Supply Chain Management.

  5. Climate Leadership Award for Supply Chain Leadership

    Science.gov (United States)

    Apply to the Climate Leadership Award for Supply Chain Leadership, which publicly recognizes organizations that are are at the leading edge of managing greenhouse gas emissions in their organizational supply chains.

  6. Responsive supply chain: modeling and simulation

    National Research Council Canada - National Science Library

    Amit Kumar Sinha; Prerna Swati; Ankush Anand

    2015-01-01

    .... is the most challenging issues even for efficient global supply chain management. Therefore, modeling of responsive supply chain is an emerging technology for sustaining any firm/industry in future competitive environment...

  7. Cybersecurity and Cyber-Resilient Supply Chains

    National Research Council Canada - National Science Library

    Hugh Boyes

    2015-01-01

    ... of increasingly global supply chains. Increased use of information technology introduces a number of cybersecurity risks affecting cyber-resilience of the supply chain, both in terms of the product or service delivered to a customer...

  8. Supply chain management in product development.

    OpenAIRE

    Tzortzopoulos, Patricia; Kagioglou, Mike; Cooper, Rachel; Dyson, E

    2009-01-01

    Mounting emphasis on construction supply chain management (CSCM) is due to both global sourcing of materials and a shortage of labor. These factors force increasing amounts of value-added work to be conducted off-site deep in the supply chain. Construction Supply Chain Management Handbookcompiles in one comprehensive source an overview of the diverse research and examples of construction supply chain practice around the world.Reflecting the emergence of CSCM as an important area of multi-nati...

  9. Supply chain dynamics in healthcare services.

    Science.gov (United States)

    Samuel, Cherian; Gonapa, Kasiviswanadh; Chaudhary, P K; Mishra, Ananya

    2010-01-01

    The purpose of this paper is to analyse health service supply chain systems. A great deal of literature is available on supply chain management in finished goods inventory situations; however, little research exists on managing service capacity when finished goods inventories are absent. System dynamics models for a typical service-oriented supply chain such as healthcare processes are developed, wherein three service stages are presented sequentially. Just like supply chains with finished goods inventory, healthcare service supply chains also show dynamic behaviour. Comparing options, service reduction, and capacity adjustment delays showed that reducing capacity adjustment and service delays gives better results. The study is confined to health service-oriented supply chains. Further work includes extending the study to service-oriented supply chains with parallel processing, i.e. having more than one stage to perform a similar operation and also to study the behaviour in service-oriented supply chains that have re-entrant orders and applications. Specific case studies can also be developed to reveal factors relevant to particular service-oriented supply chains. The paper explains the bullwhip effect in healthcare service-oriented supply chains. Reducing stages and capacity adjustment are strategic options for service-oriented supply chains. The paper throws light on policy options for managing healthcare service-oriented supply chain dynamics.

  10. Demand chain management — The implementation | Ericsson ...

    African Journals Online (AJOL)

    Most current supply chain models were developed during a period of relative stability. Today, the environment is discontinuous, volatile and unpredictable. This requires a major rethinking and revitalisation of existing supply chain models. Supply chains are much more than warehouses, transportation and technology, they ...

  11. Extending the "Knowledge Advantage": Creating Learning Chains

    Science.gov (United States)

    Maqsood, Tayyab; Walker, Derek; Finegan, Andrew

    2007-01-01

    Purpose: The purpose of this paper is to develop a synergy between the approaches of knowledge management in a learning organisation and supply chain management so that learning chains can be created in order to unleash innovation and creativity by managing knowledge in supply chains. Design/methodology/approach: Through extensive literature…

  12. Consistency and Refinement for Interval Markov Chains

    DEFF Research Database (Denmark)

    Delahaye, Benoit; Larsen, Kim Guldstrand; Legay, Axel

    2012-01-01

    Interval Markov Chains (IMC), or Markov Chains with probability intervals in the transition matrix, are the base of a classic specification theory for probabilistic systems [18]. The standard semantics of IMCs assigns to a specification the set of all Markov Chains that satisfy its interval...

  13. Principles in Halal Supply Chain Management

    NARCIS (Netherlands)

    Tieman, H.; Vorst, van der J.G.A.J.; Maznah Che Ghazali,

    2012-01-01

    Purpose – The purpose of this paper is to introduce a new framework to optimise the design of halal food supply chains, called the “Halal Supply Chain Model”. In this research the main logistics business processes are defined, which are the determinants for the halal supply chain performance.

  14. A concept for collaborative supply chain planning

    DEFF Research Database (Denmark)

    Alfnes, E.; Dreyer, H.C.; Hvolby, Hans-Henrik

    2012-01-01

    vendors such as Oracle, SAP and I2 offer supply chain planning systems. This limits the ability for SMEs to exploit the supply chain planning options. This paper is part of a research project carried out to develop a new supply chain add-on for Microsoft AX, a very common system for SMEs. The paper...

  15. DSB Task Force on Cyber Supply Chain

    Science.gov (United States)

    2017-04-01

    2 Overview of the Cyber Supply Chain Landscape .................................................................................... 4...exploitation via this shortcut to achieve the desired effect. OVERVIEW OF THE CYBER SUPPLY CHAIN LANDSCAPE The supply chain for microelectronics parts...system’s implementation and expected behaviors. Additional research could lead to architectures for achieving greater visibility Task Force on Cyber

  16. Experiences with the Mango Chain Game

    NARCIS (Netherlands)

    Meijer, S.A.; Zuñiga-Arias, G.; Sterrenburg, S.

    2005-01-01

    The mango chain game is a simulation game used for research purposes. It facilitated studying the bargaining power of Costa Rican mango producers in international supply chains of mango. The game simulates a simplified mango export chain in which real world local producers can play the role of

  17. Den teoretiske udvikling af Supply Chain Strategimodeller

    DEFF Research Database (Denmark)

    Arvad Johansen, Jens

    2011-01-01

    segmentering via postponement-princippet, har givet mærkbare forbedringer. Det beskrives endvidere, hvordan produkternes livscyklus påvirker valget af supply chain design. Begrebet Demand Chain Management( DCM), hvormed strategimodeller bruger klassiske marketingelementer sammen med Supply Chain Management...

  18. Towards the design of Secure Supply Chains

    NARCIS (Netherlands)

    Ludema, M.W.

    2009-01-01

    Supply chains are the life-lines of society and disturbances or disruptions should be avoided where possible. Secured by adequate protection is possible, but this is based on supply chain designs that are already in place. Designing secure supply chains means to understand security in relation to

  19. Secure Supply Chains : Design Restrictions & Organizational Boundaries

    NARCIS (Netherlands)

    Ludema, M.W.

    2009-01-01

    An important issue in the design of secure supply chains is the understanding of the relation between supply chains and the organizational responsibility of specific parts of these supply chains. Organizational boundaries change over time by means of vertical and/or horizontal (des)-integration and

  20. The fish industry - toward supply chain modelling

    DEFF Research Database (Denmark)

    Jensen, Toke Koldborg; Nielsen, Jette; Larsen, Erling

    2010-01-01

    Mathematical models for simulating and optimizing aspects of supply chains such as distribution, planning, and optimal handling of raw materials are widely used. However, modeling based on a holistic chain view including several or all supply chain agents is less studied, and food-related aspects...

  1. Framework for Designing Robust Supply Chains

    NARCIS (Netherlands)

    Vlajic, J.V.; Vorst, van der J.G.A.J.; Haijema, R.

    2016-01-01

    Today’s business environment and harsh competitiveness force companies and entire supply chains to increase their efficiency as much as possible. As a consequence, supply chains have become highly sensitive to disruptions and less tolerant to deviations in operations, that is, supply chains have

  2. Supply Chain Management Performance in Tourism. Continental Hotels Chain Case

    Directory of Open Access Journals (Sweden)

    Gabriela Ţigu

    2013-02-01

    Full Text Available With its origins in logistics, Supply Chain Management (SCM concept is covering all managerial aspects of the flow of materials and information from source to customer, across the entire range of materials handling and movement functions, and throughout an organization and its supply channels. In tourism, these issues relate to the whole process of providing tourism services from sourcing of raw materials, products or different services to supply and distribution, and SCM performance can ultimately be measured by customer satisfaction. Thus, an important component of tourism SCM is the demand management. Therefore, this study aims to highlight the features of the concept of SCM and demand management in tourism, with an emphasis on a hotel chain in Romania, based on research and analysis of tourist traffic indicators as well as assessment of customers satisfaction. The sources of information are the internal company statistics, as well as various hotels booking websites that offer customers’ feedback. The results of the study provide a snapshot of how the hotel demand management can influence SCM performance in tourism.

  3. What is a virtual link?

    OpenAIRE

    Kuperberg, Greg

    2002-01-01

    Several authors have recently studied virtual knots and links because they admit invariants arising from R-matrices. We prove that every virtual link is uniquely represented by a link L in S X I, a thickened, compact, oriented surface S, such that the link complement (S X I) - L has no essential vertical cylinder.

  4. Bottom-linked innovation

    DEFF Research Database (Denmark)

    Kristensen, Catharina Juul

    2018-01-01

    Employee-driven innovation is gaining ground as a strategy for developing sustainable organisations in the public and private sector. This type of innovation is characterised by active employee participation, and the bottom-up perspective is often emphasised. This article explores an issue that has...... hitherto been paid little explicit attention, namely collaboration between middle managers and employees in innovation processes. In contrast to most studies, middle managers and employees are here both subjects of explicit investigation. The collaboration processes explored in this article are termed...... ‘bottom-linked innovation’. The empirical analysis is based on an in-depth qualitative study of bottom-linked innovation in a public frontline institution in Denmark. By combining research on employee-driven innovation and middle management, the article offers new insights into such collaborative...

  5. Runtime Verification Through Forward Chaining

    Directory of Open Access Journals (Sweden)

    Alan Perotti

    2014-12-01

    Full Text Available In this paper we present a novel rule-based approach for Runtime Verification of FLTL properties over finite but expanding traces. Our system exploits Horn clauses in implication form and relies on a forward chaining-based monitoring algorithm. This approach avoids the branching structure and exponential complexity typical of tableaux-based formulations, creating monitors with a single state and a fixed number of rules. This allows for a fast and scalable tool for Runtime Verification: we present the technical details together with a working implementation.

  6. Supply chain management - safety aspects

    Directory of Open Access Journals (Sweden)

    2010-12-01

    Full Text Available Developing economy, growing customer requirements and competition make the service level higher. Delivery safety - as the highest priority - has to be maintained at the same time. Customers more and more often require transport to be very flexible, fast, and complex in terms of carrying every quantity of goods of different sizes, from and to different countries, through customs clearance, storing and distribution of shipments. Meeting these requirements depends on complex information on transport processes and their safety. The article presents safety foundations and institution Authorized Economic Operator - AEO in supply chains.

  7. Opportunities and Challenges in the Design and Analysis of Biomass Supply Chains

    Science.gov (United States)

    Lautala, Pasi T.; Hilliard, Michael R.; Webb, Erin; Busch, Ingrid; Richard Hess, J.; Roni, Mohammad S.; Hilbert, Jorge; Handler, Robert M.; Bittencourt, Roger; Valente, Amir; Laitinen, Tuuli

    2015-12-01

    The biomass supply chain is one of the most critical elements of large-scale bioenergy production and in many cases a key barrier for procuring initial funding for new developments on specific energy crops. Most productions rely on complex transforming chains linked to feed and food markets. The term `supply chain' covers various aspects from cultivation and harvesting of the biomass, to treatment, transportation, and storage. After energy conversion, the product must be delivered to final consumption, whether it is in the form of electricity, heat, or more tangible products, such as pellets and biofuels. Effective supply chains are of utmost importance for bioenergy production, as biomass tends to possess challenging seasonal production cycles and low mass, energy and bulk densities. Additionally, the demand for final products is often also dispersed, further complicating the supply chain. The goal of this paper is to introduce key components of biomass supply chains, examples of related modeling applications, and if/how they address aspects related to environmental metrics and management. The paper will introduce a concept of integrated supply systems for sustainable biomass trade and the factors influencing the bioenergy supply chain landscape, including models that can be used to investigate the factors. The paper will also cover various aspects of transportation logistics, ranging from alternative modal and multi-modal alternatives to introduction of support tools for transportation analysis. Finally gaps and challenges in supply chain research are identified and used to outline research recommendations for the future direction in this area of study.

  8. Opportunities and Challenges in the Design and Analysis of Biomass Supply Chains.

    Science.gov (United States)

    Lautala, Pasi T; Hilliard, Michael R; Webb, Erin; Busch, Ingrid; Richard Hess, J; Roni, Mohammad S; Hilbert, Jorge; Handler, Robert M; Bittencourt, Roger; Valente, Amir; Laitinen, Tuuli

    2015-12-01

    The biomass supply chain is one of the most critical elements of large-scale bioenergy production and in many cases a key barrier for procuring initial funding for new developments on specific energy crops. Most productions rely on complex transforming chains linked to feed and food markets. The term 'supply chain' covers various aspects from cultivation and harvesting of the biomass, to treatment, transportation, and storage. After energy conversion, the product must be delivered to final consumption, whether it is in the form of electricity, heat, or more tangible products, such as pellets and biofuels. Effective supply chains are of utmost importance for bioenergy production, as biomass tends to possess challenging seasonal production cycles and low mass, energy and bulk densities. Additionally, the demand for final products is often also dispersed, further complicating the supply chain. The goal of this paper is to introduce key components of biomass supply chains, examples of related modeling applications, and if/how they address aspects related to environmental metrics and management. The paper will introduce a concept of integrated supply systems for sustainable biomass trade and the factors influencing the bioenergy supply chain landscape, including models that can be used to investigate the factors. The paper will also cover various aspects of transportation logistics, ranging from alternative modal and multi-modal alternatives to introduction of support tools for transportation analysis. Finally gaps and challenges in supply chain research are identified and used to outline research recommendations for the future direction in this area of study.

  9. Option chain and change management : a structural equation application.

    OpenAIRE

    Thierry Burger-Helmchen

    2006-01-01

    The aim of this work is to establish empirically with a structural equation model (SEM) the existence of links between the options perceived by the members of an industry, the expectation of future rents produced by the exercise of these options and firm or industry specific factors. The theoretical part of this work is based on the notion of option chain developed by Bowman and Hurry (1993). The empirical part is on the video-game industry. A questionnaire based dataset on 211 video-game cre...

  10. Linking assumptions in amblyopia

    Science.gov (United States)

    LEVI, DENNIS M.

    2017-01-01

    Over the last 35 years or so, there has been substantial progress in revealing and characterizing the many interesting and sometimes mysterious sensory abnormalities that accompany amblyopia. A goal of many of the studies has been to try to make the link between the sensory losses and the underlying neural losses, resulting in several hypotheses about the site, nature, and cause of amblyopia. This article reviews some of these hypotheses, and the assumptions that link the sensory losses to specific physiological alterations in the brain. Despite intensive study, it turns out to be quite difficult to make a simple linking hypothesis, at least at the level of single neurons, and the locus of the sensory loss remains elusive. It is now clear that the simplest notion—that reduced contrast sensitivity of neurons in cortical area V1 explains the reduction in contrast sensitivity—is too simplistic. Considerations of noise, noise correlations, pooling, and the weighting of information also play a critically important role in making perceptual decisions, and our current models of amblyopia do not adequately take these into account. Indeed, although the reduction of contrast sensitivity is generally considered to reflect “early” neural changes, it seems plausible that it reflects changes at many stages of visual processing. PMID:23879956

  11. Use of simulation models to study the dynamic of recall of non-conform perishable produce through the supply chain

    DEFF Research Database (Denmark)

    Busato, P.; Sopegno, A.; Berruto, R.

    2013-01-01

    : lot size, lead time for information spreading from link to link, product transit time among links, product storage procedures and times, and the point in the supply chain where the problem occurred. To study with a system approach different scenarios for the recall procedure, a discrete event dynamic...... simulation model using Extendsim® has been developed. Here, the model framework is described and a selected example is presented....

  12. Cellular chain formation in Escherichia coli biofilms

    DEFF Research Database (Denmark)

    Vejborg, Rebecca Munk; Klemm, Per

    2009-01-01

    In this study we report on a novel structural phenotype in Escherichia coli biofilms: cellular chain formation. Biofilm chaining in E. coli K-12 was found to occur primarily by clonal expansion, but was not due to filamentous growth. Rather, chain formation was the result of intercellular......; type I fimbriae expression significantly reduced cellular chain formation, presumably by steric hindrance. Cellular chain formation did not appear to be specific to E coli K-12. Although many urinary tract infection (UTI) isolates were found to form rather homogeneous, flat biofilms, three isolates...

  13. Overseas links as export conduits

    OpenAIRE

    Hanley, Aoife

    2009-01-01

    This paper investigates the relationship between exports and overseas links using data from the UK Community Innovation Survey. Overseas vertical and horizontal links are associated with an average increase in export intensity of 74 and 156 percent for vertical and horizontal overseas links respectively. Firm size shows no significant interactions with overseas links. The data suggests that overseas links are a relatively infrequent form of conducting trade. My findings support the role of Go...

  14. Chain Analysis for Large-scale Communication Systems: A Methodology for Information Exchange in Chains

    NARCIS (Netherlands)

    Grijpink, J.H.A.M.

    2010-01-01

    The chain concept is introduced to explain how large-scale information infrastructures so often fail and sometimes even backfire. Next, the assessment framework of the doctrine of Chain-computerisation and its chain analysis procedure are outlined. In this procedure chain description precedes

  15. Single homopolypeptide chains collapse into mechanically rigid conformations

    Science.gov (United States)

    Dougan, Lorna; Li, Jingyuan; Badilla, Carmen L.; Berne, B. J.; Fernandez, Julio M.

    2009-01-01

    Huntington's disease is linked to the insertion of glutamine (Q) in the protein huntingtin, resulting in polyglutamine (polyQ) expansions that self-associate to form aggregates. While polyQ aggregation has been the subject of intense study, a correspondingly thorough understanding of individual polyQ chains is lacking. Here we demonstrate a single molecule force-clamp technique that directly probes the mechanical properties of single polyQ chains. We have made polyQ constructs of varying lengths that span the length range of normal and diseased polyQ expansions. Each polyQ construct is flanked by the I27 titin module, providing a clear mechanical fingerprint of the molecule being pulled. Remarkably, under the application of force, no extension is observed for any of the polyQ constructs. This is in direct contrast with the random coil protein PEVK of titin, which readily extends under force. Our measurements suggest that polyQ chains form mechanically stable collapsed structures. We test this hypothesis by disrupting polyQ chains with insertions of proline residues and find that their mechanical extensibility is sensitive to the position of the proline interruption. These experiments demonstrate that polyQ chains collapse to form a heterogeneous ensemble of conformations that are mechanically resilient. We further use a heat-annealing molecular dynamics protocol to extensively search the conformation space and find that polyQ can exist in highly mechanically stable compact globular conformations. The mechanical rigidity of these collapsed structures may exceed the functional ability of eukaryotic proteasomes, resulting in the accumulation of undigested polyQ sequences in vivo. PMID:19549822

  16. Parameterizing amylose chain-length distributions for biosynthesis-structure-property relations.

    Science.gov (United States)

    Nada, Sharif S; Zou, Wei; Li, Changfeng; Gilbert, Robert G

    2017-11-01

    Amylose, one of the components of starch, is a glucose polymer consisting largely of long, linear chains with a few long-chain branch points. The chain-length (molecular weight) distribution (CLD) of the component chains of amylose can provide information on amylose biosynthesis-structure-property relations, as has been done previously by fitting amylopectin CLDs to a model with physically meaningful parameters. Due to the presence of long chains, the CLD of amylose can currently best be obtained by size-exclusion chromatography, a technique that suffers from band-broadening effects which alter the observed distribution. The features of the multiple regions present in amylose chain-length distributions are also difficult to resolve, an issue that combines with band broadening to compound the difficulty of analysis and subsequent parameterization of the structural characteristics of amylose. A new method is presented to fit these distributions with biologically meaningful parameters in a way that accounts for band broadening. This is achieved by assuming that band broadening takes the form of a simple Gaussian over a relatively small region and that chain stoppage is a random process independent of the length of the substrate chain over the same region; these assumptions are relatively weak and expected to be frequently applicable. The method provides inbuilt consistency tests for its applicability to a given data set and, in cases where it is applicable, allows for the first nonempirical parameterization of amylose biosynthesis-structure-property relations from CLDs by using parameters directly linked to the activities of the enzymes responsible for chain growth and chain stoppage. Graphical abstract Model calculation illustrating the method described and showing the division between the three characteristic regions of a typical amylose chain-length distribution.

  17. Arabinosylation Plays a Crucial Role in Extensin Cross-linking

    Directory of Open Access Journals (Sweden)

    Yuning Chen

    2015-01-01

    Full Text Available Extensins (EXTs are hydroxyproline-rich glycoproteins (HRGPs that are structural components of the plant primary cell wall. They are basic proteins and are highly glycosylated with carbohydrate accounting for >50% of their dry weight. Carbohydrate occurs as monoga-lactosyl serine and arabinosyl hydroxyproline, with arabinosides ranging in size from ~1 to 4 or 5 residues. Proposed functions of EXT arabinosylation include stabilizing the polyproline II helix structure and facilitating EXT cross-linking. Here, the involvement of arabinosylation in EXT cross-linking was investigated by assaying the initial cross-linking rate and degree of cross-linking of partially or fully dearabinosylated EXTs using an in vitro cross-linking assay followed by gel permeation chromatography. Our results indicate that EXT arabinosylation is required for EXT cross-linking in vitro and the fourth arabinosyl residue in the tetraarabinoside chain, which is uniquely α-linked, may determine the initial cross-linking rate. Our results also confirm the conserved structure of the oligoarabinosides across species, indicating an evolutionary significance for EXT arabinosylation.

  18. Agrofood chains: a viable alternative for sustainable rural development or consolidation of big business?

    Directory of Open Access Journals (Sweden)

    María Rosa Yumbla

    2013-10-01

    Full Text Available Beginning in the 90s, following patterns that responded to the global corporate food regime, the government of Ecuador encouraged the formation of agro-food chains, among them, the chain of corn-animal feed- poultry. The food chain includes two service links (SL and four productive links (PL controlled by companies such as Pronaca, Agripac, Ecuaquímica and Supermaxi. These companies implemented horizontal, vertical, financial, and brand integrations, as strategies to consolidate market power and something even more prejudicial –the shaping of decisions regarding what and how to plant, and the available choices of what and how to consume– progressively creating a gap between producers and consumers.This model promotes corn monoculture through contract farming, encourages the use of agrochemicals, and endorses large poultry and swine processing factories which cause air, soil and water pollution from the ‘by products’, gas, feces and urine produced by the animals. Additionally, it promotes, supports an increases the consumption of animal protein, which is energy inefficient.The article discusses the consolidation of the agro-food chain, corn –processed food– poultry, and their links in order to determine if the integration of producers and consumers in this chain is an alternative to equitable development. Or are they part of the business strategies that respond to global food systems?

  19. Long chain branching of PLA

    Science.gov (United States)

    Gu, Liangliang; Xu, Yuewen; Fahnhorst, Grant; Macosko, Christopher W.

    2017-05-01

    A trifunctional aziridine linker, trimethylolpropane tris(2-methyl-1-aziridinepropionate) (TTMAP), was melt blended with linear polylactic acid (PLA) to make star branched PLA. Adding pyromellitic dianhydride (PMDA) led to long chain branched (LCB) PLA. Mixing torque evolution during melt processing revealed high reactivity of aziridine with the carboxyl end group on PLA and an incomplete reaction of PMDA with the hydroxyl end group. Star-shaped PLA exhibited higher viscosity but no strain hardening in extensional flow while LCB PLA showed significant extensional hardening. Excess TTMAP in the branching reaction resulted in gel formation, which led to failure at low strain in extension. PMDA conversion was estimated based on gelation theory. The strain rate dependence of extensional hardening indicated that the LCB PLA had a low concentration of long chain branched molecules with an H-shaped topology. Unlike current methods used to branch PLA, free radical chemistry or use of an epoxy functional oligomers, our branching strategy produced strain hardening with less increase in shear viscosity. This study provides guidelines for design of polymers with low shear viscosity, which reduces pressure drop in extrusion, combined with strong extensional hardening, which enhances performance in processes that involve melt stretching.

  20. The LHC Lead Injector Chain

    CERN Document Server

    Beuret, A; Blas, A; Burkhardt, H; Carli, Christian; Chanel, M; Fowler, A; Gourber-Pace, M; Hancock, S; Hourican, M; Hill, C E; Jowett, John M; Kahle, K; Küchler, D; Lombardi, A M; Mahner, E; Manglunki, Django; Martini, M; Maury, S; Pedersen, F; Raich, U; Rossi, C; Royer, J P; Schindl, Karlheinz; Scrivens, R; Sermeus, L; Shaposhnikova, Elena; Tranquille, G; Vretenar, Maurizio; Zickler, T

    2004-01-01

    A sizeable part of the LHC physics programme foresees lead-lead collisions with a design luminosity of 1027 cm-2 s-1. This will be achieved after an upgrade of the ion injector chain comprising Linac3, LEIR, PS and SPS machines [1,2]. Each LHC ring will be filled in 10 min by almost 600 bunches, each of 7×107 lead ions. Central to the scheme is the Low Energy Ion Ring (LEIR) [3,4], which transforms long pulses from Linac3 into high-brilliance bunches by means of multi-turn injection, electron cooling and accumulation. Major limitations along the chain, including space charge, intrabeam scattering, vacuum issues and emittance preservation are highlighted. The conversion from LEAR (Low Energy Antiproton Ring) to LEIR involves new magnets and power converters, high-current electron cooling, broadband RF cavities, and a UHV vacuum system with getter (NEG) coatings to achieve a few 10-12 mbar. Major hardware changes in Linac3 and the PS are also covered. An early ion scheme with fewer bunches (but each at nominal...