WorldWideScience

Sample records for cells annual subcontract

  1. Annual Report: Photovoltaic Subcontract Program FY 1990

    Energy Technology Data Exchange (ETDEWEB)

    Summers, K. A.

    1991-03-01

    This report summarizes the progress of the Photovoltaic (PV) Subcontract Program of the Solar Energy Research Institute (SERI) from October 1, 1989 through September 30, 1990. The PV Subcontract Program is responsible for managing the subcontracted portion of SERI's PV Advanced Research and Development Project. In fiscal year 1990, this included more than 54 subcontracts with a total annualized funding of approximately $11.9 million. Approximately two-thirds of the subcontracts were with universities at a total funding of nearly $3.3 million. The six technical sections of the report cover the main areas of the subcontract program: the Amorphous Silicon Research Project, Polycrystalline Thin Films, Crystalline Silicon Materials Research, High-Efficiency Concepts, the New Ideas Program, and the University Participation Program. Technical summaries of each of the subcontracted programs provide a discussion of approaches, major accomplishments in FY 1990, and future research directions. Another section introduces the PVMaT project and reports on its progress.

  2. High-efficiency thin-film cadmium telluride photovoltaic cells. Annual subcontract report, January 20, 1995--January 19, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Compaan, A D; Bohn, R G; Contreras-Puente, G [Toledo Univ., OH (United States). Dept. of Physics and Astronomy

    1996-05-01

    This annual report covers the second year of a 3-year NREL subcontract with the University of Toledo that is focused on improvements in efficiency for radio frequency (rf)-sputtered CdS/CdTe solar cells. In earlier work supported by NREL, the University of Toledo established the viability of two new deposition methods for CdS/CdTe solar cells by fabricating cells with efficiencies greater than 10% at air mass (AM) 1.5 on soda lime glass for all-sputtered cells and also for all-laser-deposited cells. Most of the effort has been placed on radio frequency sputtering (RFS) because it was judged to be more economical and more easily scaled to large-area deposition. However, laser physical vapor deposition (LPVD) has remained the method of choice for the deposition of CdCl{sub 2} layers and also for the exploration of new materials such as the ternary alloys including CdS{sub x} Te{sub 1{minus}x} and dopants such as Cu in ZnTe.

  3. Thin film cadmium telluride photovoltaic cells. Annual subcontract report, 1 November 1991--31 October 1992

    Energy Technology Data Exchange (ETDEWEB)

    Compaan, C.D.; Bohn, R.G. [Toledo Univ., OH (United States)

    1993-10-01

    This report describes work to develop and optimize radio-frequency (RF) sputtering and laser-driven physical vapor deposition (LDPVD) for CdTe-based thin-film solar cells. Both of these techniques are vacuum-based and share several other common physical principles. However, they differ somewhat in the typical kinetic energies of Cd, Te, and S that impact on the growth surface. The values of several processing parameters-optimized with the LDPVD technique-were taken as starting values for the RF sputtering method. We completed an initial optimization of the sputtering parameters for the CdTe growth and also successfully sputtered CdS for the first time. In addition, we successfully fabricated what we believe are the first CdS/CdTe cells in which RF sputtering was used for both CdS and CdTe layers. We achieved an all-LDPVD ell with an air mass (AM) 1.5 efficiency of 10.5% and an all-RF-sputtered cell with AM 1.5 efficiency of 10.4%, as tested by NREL.

  4. Thin film cadmium telluride photovoltaic cells. Annual subcontract report, 23 July 1990--31 October 1991

    Energy Technology Data Exchange (ETDEWEB)

    Compaan, A.; Bohn, R. [Toledo Univ., OH (United States)

    1992-04-01

    This report describes research to develop to vacuum-based growth techniques for CdTe thin-film solar cells: (1) laser-driven physical vapor deposition (LDPVD) and (2) radio-frequency (rf) sputtering. The LDPVD process was successfully used to deposit thin films of CdS, CdTe, and CdCl{sub 2}, as well as related alloys and doped semiconductor materials. The laser-driven deposition process readily permits the use of several target materials in the same vacuum chamber and, thus, complete solar cell structures were fabricated on SnO{sub 2}-coated glass using LDPVD. The rf sputtering process for film growth became operational, and progress was made in implementing it. Time was also devoted to enhancing or implementing a variety of film characterization systems and device testing facilities. A new system for transient spectroscopy on the ablation plume provided important new information on the physical mechanisms of LDPVD. The measurements show that, e.g., Cd is predominantly in the neutral atomic state in the plume but with a fraction that is highly excited internally ({ge} 6 eV), and that the typical neutral Cd translational kinetic energies perpendicular to the target are 20 eV and greater. 19 refs.

  5. Processing and modeling issues for thin-film solar cell devices: Annual subcontract report, January 16, 1995 -- January 15, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Birkmire, R W; Phillips, J E; Buchanan, W A; Eser, E; Hegedus, S S; McCandless, B E; Meyers, P V; Shafarman, W N [Univ. of Delaware, Newark, DE (United States)

    1996-08-01

    The overall mission of the Institute of Energy Conversion is the development of thin film photovoltaic cells, modules, and related manufacturing technology and the education of students and professionals in photovoltaic technology. The objectives of this four-year NREL subcontract are to advance the state of the art and the acceptance of thin film PV modules in the areas of improved technology for thin film deposition, device fabrication, and material and device characterization and modeling, relating to solar cells based on CuInSe{sub 2} and its alloys, on a-Si and its alloys, and on CdTe. In the area of CuInSe{sub 2} and its alloys, EEC researchers have produced CuIn{sub 1-x}GaxSe{sub 2} films by selenization of elemental and alloyed films with H{sub 2}Se and Se vapor and by a wide variety of process variations employing co-evaporation of the elements. Careful design, execution and analysis of these experiments has led to an improved understanding of the reaction chemistry involved, including estimations of the reaction rate constants. Investigation of device fabrication has also included studies of the processing of the Mo, US and ZnO deposition parameters and their influence on device properties. An indication of the success of these procedures was the fabrication of a 15% efficiency CuIn{sub 1-x}GaxSe{sub 2} solar cell.

  6. Photovoltaic Subcontract Program. Annual report, FY 1992

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    This report summarizes the fiscal year (FY) 1992 progress of the subcontracted photovoltaic (PV) research and development (R&D) performed under the Photovoltaic Advanced Research and Development Project at the National Renewable Energy Laboratory (NREL)-formerly the Solar Energy Research Institute (SERI). The mission of the national PV program is to develop PV technology for large-scale generation of economically competitive electric power in the United States. The technical sections of the report cover the main areas of the subcontract program: the Crystalline Materials and Advanced Concepts project, the Polycrystalline Thin Films project, Amorphous Silicon Research project, the Photovoltaic Manufacturing Technology (PVMaT) project, PV Module and System Performance and Engineering project, and the PV Analysis and Applications Development project. Technical summaries of each of the subcontracted programs provide a discussion of approaches, major accomplishments in FY 1992, and future research directions.

  7. Annual Report: Photovoltaic Subcontract Program FY 1991

    Energy Technology Data Exchange (ETDEWEB)

    Summers, K. A.

    1992-03-01

    This report summarizes the fiscal year (FY) 1991 (October 1, 1990, through September 30, 1991) progress of the subcontracted photovoltaic (PV) research and development (R&D) performed under the Photovoltaic Advanced Research and Development Project at the National Renewable Energy Laboratory (NREL)-formerly the Solar Energy Research Institute (SERI). The mission of the national PV program is to develop PV technology for large-scale generation of economically competitive electric power in the United States. The technical sections of the report cover the main areas of the subcontract program: the Amorphous Silicon Research Project, Polycrystalline Thin Films, Crystalline Silicon Materials Research, High Efficiency Concepts, the New Ideas Program, the University Participation Program, and the Photovoltaic Manufacturing Technology (PVMaT) project. Technical summaries of each of the subcontracted programs provide a discussion of approaches, major accomplishments in FY 1991, and future research directions.

  8. Processing and modeling issues for thin-film solar cell devices. Annual subcontract report, January 16, 1994--January 15, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Birkmire, R.W.; Phillips, J.E.; Buchanan, W.A.; Hegedus, S.S.; McCandless, B.E.; Shafarman, W.N. [Delaware Univ., Newark, DE (United States). Inst. of Energy Conversion

    1995-06-01

    This report describes results achieved during the second phase of a four year subcontract to develop and understand thin film solar cell technology related to a-Si and its alloys, CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2}, and CdTe. Accomplishments during this phase include, development of equations and reaction rates for the formation of CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} films by selenization, fabrication of a 15% efficient CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} cell, development of a reproducible, reliable Cu-diffused contact to CdTe, investigation of the role of CdTe-CdS interdiffusion on device operation, investigation of the substitution of HCl for CdCl{sub 2} in the post-deposition heat treatment of CdTe/CdS, demonstration of an improved reactor design for deposition of a-Si films, demonstration of improved process control in the fabrication of a ten set series of runs producing {approximately}8% efficient a-Si devices, demonstration of the utility of a simplified optical model for determining quantity and effect of current generation in each layer of a triple stacked a-Si cell, presentation of analytical and modeling procedures adapted to devices produced with each material system, presentation of baseline parameters for devices produced with each material system, and various investigations of the roles played by other layers in thin film devices including the Mo underlayer, CdS and ZnO in CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} devices, the CdS in CdTe devices, and the ZnO as window layer and as part of the back surface reflector in a-Si devices. In addition, collaborations with over ten research groups are briefly described. 73 refs., 54 figs., 34 tabs.

  9. Device physics of thin-film polycrystalline cells and modules. Annual subcontract report, December 6, 1993--December 5, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Sites, J.R.

    1995-05-01

    Progress has been made in several applications of device physics to thin-film polycrystalline cells and modules. At the cell level, results include a more quantitative separation of photon losses, the impact of second barriers on cell operation, and preliminary studies of how current-voltage curves are affected by band offsets. Module analysis includes the effects of the typical monolithic, series-connected cell geometry, analytical techniques when only the two module leads are accessible, and the impact of chopping frequency, local defects, and high-intensity beams on laser-scanning measurements.

  10. Basic studies of 3-5 high efficiency cell components. Annual subcontract report, 15 August 1989--14 August 1990

    Energy Technology Data Exchange (ETDEWEB)

    Lundstrom, M.S.; Melloch, M.R.; Pierret, R.F.; Carpenter, M.S.; Chuang, H.L.; Dodd, P.E.; Keshavarzi, A.; Klausmeier-Brown, M.E.; Lush, G.B.; Stellwag, T.B. [Purdue Univ., Lafayette, IN (United States)

    1993-01-01

    This project`s objective is to improve our understanding of the generation, recombination, and transport of carriers within III-V homo- and heterostructures. The research itself consists of fabricating and characterizing solar cell ``building blocks`` such as junctions and heterojunctions as well as basic measurements of material parameters. A significant effort is also being directed at characterizing loss mechanisms in high-quality, III-V solar cells fabricated in industrial research laboratories throughout the United States. The project`s goal is to use our understanding of the device physics of high-efficiency cell components to maximize cell efficiency. A related goal is the demonstration of new cell structures fabricated by molecular beam epitaxy (MBE). The development of measurement techniques and characterization methodologies is also a project objective. This report describes our progress during the fifth and final year of the project. During the past five years, we`ve teamed a great deal about heavy doping effects in p{sup +} and n{sup +} GaAs and have explored their implications for solar cells. We have developed an understanding of the dominant recombination losses in present-day, high-efficiency cells. We`ve learned to appreciated the importance of recombination at the perimeter of the cell and have developed techniques for chemically passivating such edges. Finally, we`ve demonstrated that films grown by molecular beam epitaxy are suitable for high-efficiency cell research.

  11. Device physics of thin-film polycrystalline cells and modules. Annual subcontract report, December 6, 1994--December 5, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Sites, J R [Colorado State Univ., Fort Collins, CO (United States)

    1996-08-01

    This report describes the work on a number of projects carried out at both the cell and the module level during the past year. We investigated the effects of CdS thickness in collaboration with six CdTe cell-fabrication laboratories; there appears to be a critical thickness, between 500 and 1000 {Angstrom} depending on fabrication process, below which junction quality is degraded. Our experimental and modeling project showed that conduction-band offsets less than about 0.3 eV have little effect on the performance of a CuInSe{sub 2} (CIS) or CdTe cell under the traditional assumption that the absorber material accounts for most of the depletion region. The work in several other cell projects included the role of Ga distribution in Cu{sub 1-x}Ga{sub x}Se{sub 2} (CIGS) cells, changes that occur in some cells over time, optical characterization of commonly used CdTe substrates and front contacts, and comparative characterization of CIGS cells where identical absorbers were combined with variations in window fabrication. Our work on the primary module-characterization project developed the successful use of chopping-frequency variation in a scanning beam to separate photocurrent and shunting problems affecting individual cells of an encapsulated module. Other module projects included modifications in analysis required by the typical module-cell geometry, the practical effect of nonuniformities in light intensity or cell temperature, and the advantages and pitfalls of forward bias across a module during a light scan.

  12. Processing and modeling issues for thin-film solar cell devices. Annual subcontract report, January 16, 1993--January 15, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Birkmire, R.W.; Phillips, J.E.; Buchanan, W.A.; Hegedus, S.S.; McCandless, B.E.; Shafarman, W.N.; Yokimcus, T.A. [Institute of Energy Conversion, Newark, DE (United States)

    1994-09-01

    The overall objective of the research presented in this report is to advance the development and acceptance of thin-film photovoltaic modules by increasing the understanding of film growth and processing and its relationship to materials properties and solar cell performance. The specific means toward meeting this larger goal include: (1) investigating scalable, cost-effective deposition processes; (2) preparing thin-film materials and device layers and completed cell structures; (3) performing detailed material and device analysis; and (4) participating in collaborative research efforts that address the needs of PV-manufacturers. These objectives are being pursued with CuInSe{sub 2}, CdTe and a-Si based solar cells.

  13. Polycrystalline thin film cadmium telluride solar cells fabricated by electrodeposition. Annual subcontract report, 20 March 1993--19 March 1994

    Energy Technology Data Exchange (ETDEWEB)

    Trefny, J.U.; Furtak, T.E.; Williamson, D.L.; Kim, D. [Colorado School of Mines, Golden, CO (United States)

    1994-07-01

    This report describes the principal results of work performed during the second year of a 3-year program at the Colorado School of Mines (CSM). The work on transparent conducting oxides was carried out primarily by CSM students at NREL and is described in three publications listed in Appendix C. The high-quality ZnO produced from the work was incorporated into a copper indium diselenide cell that exhibited a world-record efficiency of 16.4%. Much of the time was devoted to the improvement of cadmium sulfide films deposited by chemical bath deposition methods and annealed with or without a cadmium chloride treatment. Progress was also made in the electrochemical deposition of cadmium telluride. High-quality films yielding CdS/CdTe/Au cells of greater than 10% efficiency are now being produced on a regular basis. We explored the use of zinc telluride back contacts to form an n-i-p cell structure as previously used by Ametek. We began small-angle x-ray scattering (SAXS) studies to characterize crystal structures, residual stresses, and microstructures of both CdTe and CdS. Large SAXS signals were observed in CdS, most likely because of scattering from gain boundaries. The signals observed to date from CdTe are much weaker, indicating a more homogeneous microstructure. We began to use the ADEPT modeling program, developed at Purdue University, to guide our understanding of the CdS/CdTe cell physics and the improvements that will most likely lead to significantly enhanced efficiencies.

  14. High-efficiency, thin-film cadmium telluride photovoltaic cells. Annual subcontract report, 20 January 1994--19 January 1995

    Energy Technology Data Exchange (ETDEWEB)

    Compaan, A.D.; Bohn, R.G.; Rajakarunanayake, Y. [Toledo Univ., OH (United States)

    1995-08-01

    This report describes work performed to develop and optimize the process of radio frequency (RF) sputtering for the fabrication of thin-film solar cells on glass. The emphasis is on CdTe-related materials including CdTe, CdS, ZnTe, and ternary alloy semiconductors. Pulsed laser physical vapor deposition (LPVD) was used for exploratory work on these materials, especially where alloying or doping are involved, and for the deposition of cadmium chloride layers. For the sputtering work, a two-gun sputtering chamber was implemented, with optical access for monitoring temperature and growth rate. We studied the optical and electrical properties of the plasmas produced by two different kinds of planar magnetron sputter guns with different magnetic field configurations and strengths. Using LPVD, we studied alloy semiconductors such as CdZnTe and heavily doped semiconductors such as ZnTe:Cu for possible incorporation into graded band gap CdTe-based photovoltaic devices.

  15. Polycrystalline CuInSe{sub 2} and CdTe PV solar cells. Annual subcontract report, 15 April 1993--14 April 1994

    Energy Technology Data Exchange (ETDEWEB)

    Dhere, N.G. [Florida Solar Energy Center, Cape Canaveral, FL (United States)

    1994-11-01

    This is an annual technical report on the Phase 2 of a three-year phased research program. The principal objective of the research project is to develop novel and low-cost processes for the fabrication of stable and efficient CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} and CdTe polycrystalline-thin-film solar cells using reliable techniques amenable to scale-up for economic, large-scale manufacture. The aims are to develop a process for the non-toxic selenization so as to avoid the use of extremely toxic H{sub 2}Se in the fabrication of CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} thin-film solar cells; to optimize selenization parameters; to develop a process for the fabrication of CdTe solar cells using Cd and Te layers sputtered from elemental targets; to develop an integrated process for promoting the interdiffusion between Cd/Te layers, CdTe phase formation, grain growth, type conversion, and junction formation; to improve adhesion; to minimize residual stresses; to improve the metallic back-contact; to improve the uniformity, stoichiometry, and morphology of CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} and CdTe thin films; and to improve the efficiency of CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} and CdTe solar cells.

  16. Development of high-efficiency, thin-film CdTe solar cells. Annual subcontract report, January 1, 1993--December 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Rohatgi, A.; Chou, H.C.; Kamra, S.; Bhat, A. [Georgia Institute of Technology, Atlanta, GA (United States)

    1994-09-01

    Polycrystalline thin film CdTe solar cells are one of the leading candidates for terrestrial photovoltaic applications. Theoretical calculations project an efficiency of 27% for single crystal, single junction CdTe cells, and the practically achievable efficiency for polycrystalline CdTe cells is 18-20%. Polycrystalline CdTe cells made by different groups show a significant variation in short circuit currents, open circuit voltages, and cell efficiencies. A better understanding of carrier loss and transport mechanism is crucial for explaining these differences, improving the yield, and bridging the gap between current and practically achievable limits in CdTe cell efficiencies. The goal of this program is to improve the understanding of the loss mechanisms in thin film CdS/CdTe solar cells and to improve their efficiency by characterizing the properties of the films as well as the finished devices.

  17. Stable, high-efficiency amorphous silicon solar cells with low hydrogen content. Annual subcontract report, 1 March 1991--31 January 1992

    Energy Technology Data Exchange (ETDEWEB)

    Fortmann, C.M.; Hegedus, S.S. [Institute of Energy Conversion, Newark, DE (United States)

    1992-12-01

    Results and conclusions obtained during a research program of the investigation of amorphous silicon and amorphous silicon based alloy materials and solar cells fabricated by photo-chemical vapor and glow discharge depositions are reported. Investigation of the effects of the hydrogen content in a-si:H i-layers in amorphous silicon solar cells show that cells with lowered hydrogen content i-layers are more stable. A classical thermodynamic formulation of the Staebler-Wronski effect has been developed for standard solar cell operating temperatures and illuminations. Methods have been developed to extract a lumped equivalent circuit from the current voltage characteristic of a single junction solar cell in order to predict its behavior in a multijunction device.

  18. High-efficiency cadmium and zinc-telluride-based thin-film solar cells. Annual subcontract report, 1 March 1990--28 February 1991

    Energy Technology Data Exchange (ETDEWEB)

    Rohatgi, A.; Sudharsanan, R.; Ringel, S. [Georgia Inst. of Tech., Atlanta, GA (United States)

    1992-02-01

    This report describes research into polycrystalline CdTe solar cells grown by metal-organic chemical vapor deposition. Efficiencies of {approximately}10% were achieved using both p-i-n and p-n structures. A pre-heat treatment of CdS/SnO{sub 2}/glass substrates at 450{degrees}C in hydrogen atmosphere prior to the CdTe growth was found to be essential for high performance because this heat treatment reduces oxygen-related defects from the CdS surface. However, this treatment also resulted in a Cd-deficient CdS surface, which may in part limit the CdTe cell efficiency to 10% due to Cd vacancy-related interface defects. Preliminary model calculations suggest that removing these states can increase the cell efficiency from 10% to 13.5%. Photon absorption in the CdS film also limits the cell performance, and eliminating this loss mechanism can result in CdTe efficiencies in excess of 18%. Polycrystalline, 1.7-e, CdZnTe films were also grown for tandem-cell applications. CdZnTe/CdS cells processed using the standard CdTe cell fabrication procedure resulted in 4.4% efficiency, high series resistance, and a band-gap shift to 1.55 eV. The formation of Zn-O at and near the CdZnTe surface is the source of high contact resistance. A saturated dichromate each prior to contact deposition was found to solve the contact resistance problem. The CdCl{sub 2} treatment was identified as the cause of the observed band-gap shift due to the preferred formation of ZnCl{sub 2}. 59 refs.

  19. Polycrystalline CuInSe{sub 2} and CdTe solar cells. Annual subcontract report, April 15, 1992--April 14, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Dhere, N.G. [Florida Solar Energy Center, Cape Canaveral, FL (United States)

    1994-08-01

    The principal objective of the research project is to develop processes for the fabrication of cadmium-telluride, CdTe, and copper-indium-gallium-diselenide, Cu(In{sub 1{minus}x}Ga{sub x})Se{sub 2}, polycrystalline-thin-film solar cells using techniques that can be scaled-up for economic manufacture on a large scale. The aims are to fabricate CdTe solar cells using Cd and Te layers sputtered from elemental targets; to promote the interdiffusion between Cd/Te layers, CdTe phase formation, and grain growth; to utilize non-toxic selenization so as to avoid the use of extremely toxic H{sub 2}Se in the fabrication of Cu(In{sub l{minus}x}Ga{sub x})Se{sub 2} thin-film solar cells; to optimize selenization parameters; to improve adhesion; to minimize residual stresses; to improve the uniformity, stoichiometry, and morphology of CdTe and Cu(In{sub 1{minus}x}Ga{sub x})Se{sub 2} thin films, and the efficiency of CdTe and Cu(In{sub 1{minus}x}Ga{sub x})Se{sub 2} solar cells.

  20. High efficiency cadmium telluride and zinc telluride based thin-film solar cells. Annual subcontract report, 1 March 1990--28 February 1992

    Energy Technology Data Exchange (ETDEWEB)

    Rohatgi, A.; Sudharsanan, R.; Ringel, S.A.; Chou, H.C. [Georgia Inst. of Tech., Atlanta, GA (United States)

    1992-10-01

    This report describes work to improve the basic understanding of CdTe and ZnTe alloys by growing and characterizing these films along with cell fabrication. The major objective was to develop wide-band-gap (1.6--1.8 eV) material for the top cell, along with compatible window material and transparent ohmic contacts, so that a cascade cell design can be optimized. Front-wall solar cells were fabricated with a glass/SnO{sub 2}/CdS window, where the CdS film is thin to maximize transmission and current. Wide-band-gap absorber films (E{sub g} = 1.75 eV) were grown by molecular beam epitaxy (MBE) and metal-organic chemical vapor deposition (MOCVD) techniques, which provided excellent control for tailoring the film composition and properties. CdZnTe films were grown by both MBE and MOCVD. All the as-grown films were characterized by several techniques (surface photovoltage spectroscopy, Auger electron spectroscopy (AES), and x-ray photoelectron spectroscopy (XPS)) for composition, bulk uniformity, thickness, and film and interface quality. Front-wall-type solar cells were fabricated in collaboration with Ametek Materials Research Laboratory using CdTe and CdZnTe polycrystalline absorber films. The effects of processing on ternary film were studied by AES and XPS coupled with capacitance voltage and current voltage measurements as a function of temperature. Bias-dependent spectral response and electrical measurements were used to test some models in order to identify and quantify dominant loss mechanisms.

  1. Research on polycrystalline thin-film CuInGaSe{sub 2} solar cells. Annual subcontract report, 3 May 1991--21 May 1993

    Energy Technology Data Exchange (ETDEWEB)

    Chen, W.S.; Stewart, J.M.; Mickelsen, R.A.; Devaney, W.E.; Stanbery, B.J. [Boeing Co., Seattle, WA (United States). Defense and Space Systems Group

    1993-10-01

    This report describes work to fabricate high-efficiency CdZnS/CuInGaSe{sub 2}, thin-film solar cells and to develop improved transparent conductor window layers such as ZnO. The specific technical milestone for Phase I was to demonstrate an air mass (AM) 1.5 global 13% , 1-cm{sup 2} total-area CuInGaSe{sub 2} (CIGS) thin-film solar cell. For Phase II, the objective was to demonstrate an AM1.5 global 13.5%, 1-cm{sup 2} total-area efficiency. We focused our activities on three areas. First, we modified the CIGS deposition system to double its substrate capacity. Second, we developed new tooling to enable investigation of a modified aqueous CdZnS process in which the goal was to improve the yield of this critical step in the device fabrication process. Third, we upgraded the ZnO sputtering system to improve its reliability and reproducibility. A dual rotatable cathode metallic source was installed, and the sputtering parameters were further optimized to improve ZnO`s properties as a transparent conducting oxide (TCO). Combining the refined CdZnS process with CIGS from the newly fixtured deposition system enable us to fabricate and deliver a ZnO/Cd{sub 0.08}Zn{sub 0.20}S/CuIn{sub 0.74}Ga{sub 0.26}Se{sub 2} cell on alumina with I-V characteristics, as measured by NREL under standard test conditions, of 13.7% efficiency with V{proportional_to} = 0.5458 V, J{sub sc} = 35.48 mA/cm{sup 2}, FF = 0.688, and efficiency = 14.6%.

  2. Photovoltaic Subcontract Program, FY 1991. Annual report, [October 1, 1990--September 30, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This report summarizes the fiscal year (FY) 1991 (October 1, 1990, through September 30, 1991) progress of the subcontracted photovoltaic (PV) research and development (R&D) performed under the Photovoltaic Advanced Research and Development Project at the National Renewable Energy Laboratory (NREL) -- formerly the Solar Energy Research Institute (SERI). The mission of the national PV program is to develop PV technology for large-scale generation of economically competitive electric power in the United States. The technical sections of the report cover the main areas of the subcontract program: the Amorphous Silicon Research Project, Polycrystalline Thin Films, Crystalline Silicon Materials Research, High-Efficiency Concepts, the New Ideas Program, the University Participation Program, and the Photovoltaic Manufacturing Technology (PVMaT) project. Technical summaries of each of the subcontracted programs provide a discussion of approaches, major accomplishments in FY 1991, and future research directions.

  3. Amorphous silicon batch process cost analysis. Annual subcontract report, 11 March 1991--28 February 1993

    Energy Technology Data Exchange (ETDEWEB)

    Whisnant, R.A. [Research Triangle Inst., Research Triangle Park, NC (United States); Sherring, C. [Sherring Energy Associates, Princeton, NJ (United States)

    1993-08-01

    This report describes the development of baseline manufacturing cost data to assist PVMaT monitoring teams in assessing current and future subcontracts, which an emphasis on commercialization and production. A process for the manufacture of a single-junction, large-area, a Si module was modeled using an existing Research Triangle Institute (RTI) computer model. The model estimates a required, or breakeven, price for the module based on its production process and the financial structure of the company operating the process. Sufficient detail on cost drivers is presented so the relationship of the process features and business characteristics can be related to the estimated required price.

  4. Photovoltaic Subcontract Program, FY 1990

    Energy Technology Data Exchange (ETDEWEB)

    Summers, K.A. (ed.)

    1991-03-01

    This report summarizes the progress of the subcontracted photovoltaic (PV) research and development (R D) performed under the Photovoltaics Program at the Solar Energy Research Institute (SERI). The SERI subcontracted PV research and development represents most of the subcontracted R D that is funded by the US Department of Energy (DOE) National Photovoltaics Program. This report covers fiscal year (FY) 1990: October 1, 1989 through September 30, 1990. During FY 1990, the SERI PV program started to implement a new DOE subcontract initiative, entitled the Photovoltaic Manufacturing Technology (PVMaT) Project.'' Excluding (PVMaT) because it was in a start-up phase, in FY 1990 there were 54 subcontracts with a total annualized funding of approximately $11.9 million. Approximately two-thirds of those subcontracts were with universities, at a total funding of over $3.3 million. Cost sharing by industry added another $4.3 million to that $11.9 million of SERI PV subcontracted R D. The six technical sections of this report cover the previously ongoing areas of the subcontracted program: the Amorphous Silicon Research Project, Polycrystalline Thin Films, Crystalline Silicon Materials Research, High-Efficiency Concepts, the New Ideas Program, and the University Participation Program. Technical summaries of each of the subcontracted programs discuss approaches, major accomplishments in FY 1990, and future research directions. Another section introduces the PVMaT project and reports the progress since its inception in FY 1990. Highlights of technology transfer activities are also reported.

  5. Development of a computer model for polycrystalline thin-film CuInSe{sub 2} and CdTe solar cells; Annual subcontract report, 1 March 1992--28 February 1993

    Energy Technology Data Exchange (ETDEWEB)

    Gray, J.L.; Schwartz, R.J.; Lee, Y.J. [Purdue Univ., West Lafayette, IN (United States)

    1994-03-01

    Solar cells operate by converting the radiation power from sun light into electrical power through photon absorption by semiconductor materials. The elemental and compound material systems widely used in photovoltaic applications can be produced in a variety of crystalline and non-crystalline forms. Although the crystalline group of materials have exhibited high conversion efficiencies, their production cost are substantially high. Several candidates in the poly- and micro-crystalline family of materials have recently gained much attention due to their potential for low cost manufacturability, stability, reliability and good performance. Among those materials, CuInSe{sub 2} and CdTe are considered to be the best choices for production of thin film solar cells because of the good optical properties and almost ideal band gap energies. Considerable progress was made with respect to cell performance and low cost manufacturing processes. Recently conversion efficiencies of 14.1 and 14.6% have been reported for CuInSe{sub 2} and CdTe based solar cells respectively. Even though the efficiencies of these cells continue to improve, they are not fully understood materials and there lies an uncertainty in their electrical properties and possible attainable performances. The best way to understand the details of current transport mechanisms and recombinations is to model the solar cells numerically. By numerical modeling, the processes which limit the cell performance can be sought and therefore, the most desirable designs for solar cells utilizing these materials as absorbers can be predicted. The problems with numerically modeling CuInSe{sub 2} and CdTe solar cells are that reported values of the pertinent material parameters vary over a wide range, and some quantities such as carrier concentration are not explicitly controlled.

  6. Development of a computer model for polycrystalline thin-film CuInSe{sub 2} and CdTe solar cells. Annual subcontract report, 1 January 1990--31 December 1990

    Energy Technology Data Exchange (ETDEWEB)

    Gray, J.L.; Schwartz, R.J.; Lee, Y.J. [Purdue Univ., Lafayette, IN (United States)

    1992-04-01

    This report describes work to develop a highly accurate numerical model for CuInSe{sub 2} and CdTe solar cells. ADEPT (A Device Emulation Program and Toolbox), a one-dimensional semiconductor device simulation code developed at Purdue University, was used as the basis of this model. An additional objective was to use ADEPT to analyze the performance of existing and proposed CuInSe{sub 2} and CdTe solar cell structures. The work is being performed in two phases. The first phase involved collecting device performance parameters, cell structure information, and material parameters. This information was used to construct the basic models to simulate CuInSe{sub 2} and CdTe solar cells. This report is a tabulation of information gathered during the first phase of this project on the performance of existing CuInSe{sub 2} and CdTe solar cells, the material properties of CuInSr{sub 2}, CdTe, and CdS, and the optical absorption properties of CuInSe{sub 2}, CdTe, and CdS. The second phase will entail further development and the release of a version of ADEPT tailored to CuInSe{sub 2} and CdTe solar cells that can be run on a personal computer. In addition, ADEPT will be used to analyze the performance of existing and proposed CuInSe{sub 2} and CdTe solar cell structures. 110 refs.

  7. Advanced processing of CdTe- and CuIn{sub x}Ga{sub 1{minus}x}Se{sub 2}-based solar cells. Phase 1 annual subcontract report, 18 April 1995--17 April 1996

    Energy Technology Data Exchange (ETDEWEB)

    Morel, D L; Ferekides, C S [Univ. of South Florida, Tampa, FL (United States)

    1997-03-01

    The main objective of this project to develop high-efficiency CdTe solar cells based on processing conditions favorable for manufacturing processes. This report presents the results on work performed during the first phase of this project. One of the major issues addressed is the use of soda-lime glass substrates in place of the borosilicate glass often used for laboratory devices; another task is the preparation of Cu(In, Ga) Se{sub 2} solar cells by selenizing suitable precursor films. Emphasis is placed on processing and how different reaction schemes affect device performance. It was found that different reaction schemes not only change the bulk properties of Cu(In, Ga) Se{sub 2}, but also its surface properties, which critically affect device performance. Although the objective is to optimize processing to meet the manufacturing constraints, work has not been limited within these requirements.

  8. Polycrystalline thin film materials and devices. Annual subcontract report, 16 January 1991--15 January 1992

    Energy Technology Data Exchange (ETDEWEB)

    Baron, B.N.; Birkmire, R.W.; Phillips, J.E.; Shafarman, W.N.; Hegedus, S.S.; McCandless, B.E. [Delaware Univ., Newark, DE (United States). Inst. of Energy Conversion

    1992-10-01

    Results of Phase II of a research program on polycrystalline thin film heterojunction solar cells are presented. Relations between processing, materials properties and device performance were studied. The analysis of these solar cells explains how minority carrier recombination at the interface and at grain boundaries can be reduced by doping of windows and absorber layers, such as in high efficiency CdTe and CuInSe{sub 2} based solar cells. The additional geometric dimension introduced by the polycrystallinity must be taken into consideration. The solar cells are limited by the diode current, caused by recombination in the space charge region. J-V characteristics of CuInSe{sub 2}/(CdZn)S cells were analyzed. Current-voltage and spectral response measurements were also made on high efficiency CdTe/CdS thin film solar cells prepared by vacuum evaporation. Cu-In bilayers were reacted with Se and H{sub 2}Se gas to form CuInSe{sub 2} films; the reaction pathways and the precursor were studied. Several approaches to fabrication of these thin film solar cells in a superstrate configuration were explored. A self-consistent picture of the effects of processing on the evolution of CdTe cells was developed.

  9. Polycrystalline thin film materials and devices. Annual subcontract report, 16 January 1990--15 January 1991

    Energy Technology Data Exchange (ETDEWEB)

    Baron, B.N.; Birkmire, R.W.; Phillips, J.E.; Shafarman, W.N.; Hegedus, S.S.; McCandless, B.E. [Delaware Univ., Newark, DE (United States). Inst. of Energy Conversion

    1991-11-01

    Results and conclusion of Phase I of a multi-year research program on polycrystalline thin film solar cells are presented. The research comprised investigation of the relationships among processing, materials properties and device performance of both CuInSe{sub 2} and CdTe solar cells. The kinetics of the formation of CuInSe{sub 2} by selenization with hydrogen selenide was investigated and a CuInSe{sub 2}/CdS solar cell was fabricated. An alternative process involving the reaction of deposited copper-indium-selenium layers was used to obtain single phase CuInSe{sub 2} films and a cell efficiency of 7%. Detailed investigations of the open circuit voltage of CuInSe{sub 2} solar cells showed that a simple Shockley-Read-Hall recombination mechanism can not account for the limitations in open circuit voltage. Examination of the influence of CuInSe{sub 2} thickness on cell performance indicated that the back contact behavior has a significant effect when the CuInSe{sub 2} is less than 1 micron thick. CdTe/CdS solar cells with efficiencies approaching 10% can be repeatedly fabricated using physical vapor deposition and serial post deposition processing. The absence of moisture during post deposition was found to be critical. Improvements in short circuit current of CdTe solar cells to levels approaching 25 mA/cm{sup 2} are achievable by making the CdS window layer thinner. Further reductions in the CdS window layer thickness are presently limited by interdiffusion between the CdS and the CdTe. CdTe/CdS cells stored without protection from the atmosphere were found to degrade. The degradation was attributed to the metal contact. CdTe cells with ZnTe:Cu contacts to the CdTe were found to be more stable than cells with metal contacts. Analysis of current-voltage and spectral response of CdTe/CdS cells indicates the cell operates as a p-n heterojunction with the diode current dominated by SRH recombination in the junction region of the CdTe.

  10. Non-H{sub 2}Se, ultra-thin CIS devices. Annual subcontract report, 10 March 1992--9 November 1992

    Energy Technology Data Exchange (ETDEWEB)

    Delahoy, A.E.; Britt, J.; Kiss, Z. [Energy Photovoltaics, Inc., Princeton, NJ (United States)

    1993-02-01

    This report describes work done during Phase I of a 3-phase, cost- shared contract. Objective of the subcontract is to demonstrate 12% total-area efficiency copper indium diselenide (CIS) solar cells and 50-W CIS modules average at least 8 W/ft{sup 2} in the third year. At the end of Phase I, EPV delivered to NREL a 1.1 cm{sup 2} CIS cell with an active area efficiency of 10.5%. the corresponding total-area efficiency is 7.9%.

  11. High throughput manufacturing of thin-film CdTe photovoltaic modules. Annual subcontract report, 16 November 1993--15 November 1994

    Energy Technology Data Exchange (ETDEWEB)

    Sandwisch, D W [Solar Cells, Inc., Toledo, OH (United States)

    1995-11-01

    This report describes work performed by Solar Cells, Inc. (SCI), under a 3-year subcontract to advance SCI`s PV manufacturing technologies, reduce module production costs, increase module performance, and provide the groundwork for SCI to expand its commercial production capacities. SCI will meet these objectives in three phases by designing, debugging, and operating a 20-MW/year, automated, continuous PV manufacturing line that produces 60-cm {times} 120-cm thin-film CdTe PV modules. This report describes tasks completed under Phase 1 of the US Department of Energy`s PV Manufacturing Technology program.

  12. High-throughput manufacturing of thin-film CdS/CdTe photovoltaic modules. Annual subcontract report, 16 September 1996--15 January 1998

    Energy Technology Data Exchange (ETDEWEB)

    Sandwisch, D.W. [Solar Cells, Inc., Toledo, OH (United States)

    1998-08-01

    Cadmium telluride (CdTe) is recognized as one of the leading materials for low-cost photovoltaic modules. Solar Cells, Inc., has developed this technology and is scaling its pilot production capabilities to a multi-megawatt level. The Photovoltaic Manufacturing Technology (PVMaT) subcontract supports these efforts. Activities during the third phase of the program concentrated on process development, equipment design and testing, quality assurance, ES and H programs, and large-scale next-generation coating-system prototype development. These efforts broadly addressed the issues of the manufacturing process for producing thin-film, monolithic CdS/CdTe photovoltaic modules.

  13. 48 CFR 952.225-70 - Subcontracting for nuclear hot cell services.

    Science.gov (United States)

    2010-10-01

    ... related to the examination of, or performance of various operations on, nuclear fuel rods, control... from nuclear reactors, which are performed in specialized facilities located away from commercial... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Subcontracting for...

  14. Device Physics of Thin-Film Polycrystalline Cells and Modules; Final Subcontract Report; 6 December 1993-15 March 1998

    Energy Technology Data Exchange (ETDEWEB)

    Sites, J. R. (Department of Physics, Colorado State University, Ft. Collins, Colorado)

    1999-05-03

    This report describes work performed under this subcontract by Colorado State University (CSU). The results of the subcontract effort included progress in understanding CdTe and Cu(In1-xGax)Se2-based solar cells, in developing additional measurement and analysis techniques at the module level, and in strengthening collaboration within the thin-film polycrystalline solar-cell community. A major part of the CdTe work consisted of elevated-temperature stress tests to determine fabrication and operation conditions that minimize the possibility of long-term performance changes. Other CdTe studies included analysis of the back-contact junction, complete photon accounting, and the tradeoff with thin CdS between photocurrent gain and voltage loss. The Cu(In1-xGax)Se2 studies included work on the role of sodium in enhancing performance, the conditions under which conduction-band offsets affect cell performance, the transient effects of cycling between light and dark conditions, and detailed analysis of several individual series of cells. One aspect of thin-film module analysis has been addressing the differences in approach needed for relatively large individual cells made without grids. Most work, however, focused on analysis of laser-scanning data, including defect signatures, photocurrent/shunting separation, and the effects of forward bias or high-intensity light. Collaborations with other laboratories continued on an individual basis, and starting in 1994, collaboration was through the national R&D photovoltaic teams. CSU has been heavily involved in the structure and logistics of both the CdTe and CIS teams, as well as making frequent technical contributions in both areas.

  15. High Volume Manufacturing of Silicon-Film Solar Cells and Modules; Final Subcontract Report, 26 February 2003 - 30 September 2003

    Energy Technology Data Exchange (ETDEWEB)

    Rand, J. A.; Culik, J. S.

    2005-10-01

    The objective of the PV Manufacturing R&D subcontract was to continue to improve AstroPower's technology for manufacturing Silicon-Film* wafers, solar cells, and modules to reduce costs, and increase production yield, throughput, and capacity. As part of the effort, new technology such as the continuous back metallization screen-printing system and the laser scribing system were developed and implemented. Existing processes, such as the silicon nitride antireflection coating system and the fire-through process were optimized. Improvements were made to the statistical process control (SPC) systems of the major manufacturing processes: feedstock preparation, wafer growth, surface etch, diffusion, and the antireflection coating process. These process improvements and improved process control have led to an increase of 5% relative power, and nearly 15% relative improvement in mechanical and visual yield.

  16. Photovoltaic Subcontract Program

    Energy Technology Data Exchange (ETDEWEB)

    Surek, Thomas; Catalano, Anthony

    1993-03-01

    This report summarizes the fiscal year (FY) 1992 progress of the subcontracted photovoltaic (PV) research and development (R D) performed under the Photovoltaic Advanced Research and Development Project at the National Renewable Energy Laboratory (NREL)-formerly the Solar Energy Research Institute (SERI). The mission of the national PV program is to develop PV technology for large-scale generation of economically competitive electric power in the United States. The technical sections of the report cover the main areas of the subcontract program: the Crystalline Materials and Advanced Concepts project, the Polycrystalline Thin Films project, Amorphous Silicon Research project, the Photovoltaic Manufacturing Technology (PVMaT) project, PV Module and System Performance and Engineering project, and the PV Analysis and Applications Development project. Technical summaries of each of the subcontracted programs provide a discussion of approaches, major accomplishments in FY 1992, and future research directions.

  17. Efficiency Improvement of Crystalline Solar Cells: Final Subcontract Report, 1 January 2002 - 30 September 2006

    Energy Technology Data Exchange (ETDEWEB)

    Weber, E. R.

    2007-11-01

    UC-Berkeley study of transition metal related defects in PV-grade mc-Si to understand their pathways into solar cells; chemical state/distribution; interaction with structural defects; defect engineering.

  18. Innovative sputtering techniques for CIS and CdTe submodule fabrication. Annual subcontract report, 1 September 1991--31 August 1992

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, J.M.; Misra, M.S.; Lanning, B. [Martin Marietta Aerospace, Denver, CO (United States). Astronautics Group

    1993-03-01

    This report describes work done during Phase 1 of the subject subcontract. The subcontract was designed to study innovative deposition techniques, such as the rotating cylindrical magnetron sputtering system and electrodeposition for large-area, low-cost copper indium diselenide (CIS) and cadmium telluride (CdTe) devices. A key issue for photovoltaics (PV) in terrestrial and future space applications is producibility, particularly for applications using a large quantity of PV. Among the concerns for fabrication of polycrystalline thin-film PV, such as CIS and CdTe, are production volume, cost, and minimization of waste. Both rotating cylindrical magnetron (C-Mag{trademark}) sputtering and electrodeposition have tremendous potential for the fabrication of polycrystalline thin-film PV due to scaleability, efficient utilization of source materials, and inherently higher deposition rates. In the case of sputtering, the unique geometry of the C-Mae facilitates innovative cosputtering and reactive sputtering that could lead to greater throughput reduced health and safety risks, and, ultimately, lower fabrication cost. Electrodeposited films appear to be adherent and comparable with low-cost fabrication techniques. Phase I involved the initial film and device fabrication using the two techniques mentioned herein. Devices were tested by both internal facilities, as well as NREL and ISET.

  19. SUBCONTRACT REPORT: DC-DC Converter for Fuel Cell and Hybrid Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Marlino, Laura D [ORNL; Zhu, Lizhi [Ballard Power Systems/Siemens VDO

    2007-07-01

    The goal of this project is to develop and fabricate a 5kW dc-dc converter with a baseline 14V output capability for fuel cell and hybrid vehicles. The major objectives for this dc-dc converter technology are to meet: Higher efficiency (92%); High coolant temperature,e capability (105 C); High reliability (15 Years/150,000miles); Smaller volume (5L); Lower weight (6kg); and Lower cost ($75/kW). The key technical challenge for these converters is the 105 C coolant temperatures. The power switches and magnetics must be designed to sustain these operating temperatures reliably, without a large cost/mass/volume penalty.

  20. Research Leading to High Throughput Manufacturing of Thin-Film CdTe PV Modules: Annual Subcontract Report, September 2004--September 2005

    Energy Technology Data Exchange (ETDEWEB)

    Powell, R. C.

    2006-04-01

    Specific overall objectives of this subcontract are improvement in baseline field performance of manufactured CdTe PV modules while reducing environmental, health and safety risk in the manufacturing environment. Project objectives focus on four broad categories: (1) development of advanced front-contact window layers, (2) improved semiconductor film deposition, (3) development of improved accelerated life test procedures that indicate baseline field performance, and (4) reduction of cadmium-related environmental, health and safety risks. First Solar has significantly increased manufacturing capacity from less than 2 MW/yr to more than 20 MW/yr, while increasing the average module total-area power conversion efficiency from 7% to >9%. First Solar currently manufactures and sells 50-65-W thin-film CdTe PV modules at a rate of about 1.9 MW/month. Sales backlog (booked sales less current inventory divided by production rate) is more than a year. First Solar is currently building new facilities and installing additional equipment to increase production capacity by 50 MW/yr; the additional capacity is expected to come on line in the third quarter of 2006.

  1. Atmospheric pressure chemical vapor deposition of CdTe for high efficiency thin film PV devices: Annual subcontract report, 26 January 1999--25 January 2000

    Energy Technology Data Exchange (ETDEWEB)

    Meyers, P. V.; Kee, R.; Wolden, C.; Kestner, J.; Raja, L.; Kaydanov, V.; Ohno, T.; Collins, R.; Fahrenbruch, A.

    2000-05-30

    ITN's three year project Atmospheric Pressure Chemical Vapor Deposition (APCVD) of CdTe for High Efficiency Thin Film PV Devices has the overall objectives of improving thin film CdTe PV manufacturing technology and increasing CdTe PV device power conversion efficiency. CdTe deposition by APCVD employs the same reaction chemistry as has been used to deposit 16% efficient CdTe PV films, i.e., close spaced sublimation, but employs forced convection rather than diffusion as a mechanism of mass transport. Tasks of the APCVD program center on demonstration of APCVD of CdTe films, discovery of fundamental mass transport parameters, application of established engineering principles to the deposition of CdTe films, and verification of reactor design principles which could be used to design high throughput, high yield manufacturing equipment. Additional tasks relate to improved device measurement and characterization procedures that can lead to a more fundamental understanding of CdTe PV device operation and ultimately to higher device conversion efficiency and greater stability. Under the APCVD program, device analysis goes beyond conventional one-dimensional device characterization and analysis toward two dimension measurements and modeling. Accomplishments of the second year of the APCVD subcontract include: deposition of the first APCVD CdTe; identification of deficiencies in the first generation APCVD reactor; design, fabrication and testing of a ``simplified'' APCVD reactor; deposition of the first dense, adherent APCVD CdTe films; fabrication of the first APCVD CdTe PV device; modeling effects of CdSTe and SnOx layers; and electrical modeling of grain boundaries.

  2. Subcontracting Railway Maintenance

    DEFF Research Database (Denmark)

    Thommesen, Jacob

    2010-01-01

    In several European countries, national railway operators have been dismantled and partly privatized to create new contractual relations where operations originally performed internally are now outsourced to several companies. Breaking up work across several independent organizational and commerc......In several European countries, national railway operators have been dismantled and partly privatized to create new contractual relations where operations originally performed internally are now outsourced to several companies. Breaking up work across several independent organizational...... railway infrastructure manager (InfraMan), whichis subcontracting maintenance tasks to other companies. InfraMan has implemented various central elements in managing their subcontractors. The latter are required to present a safety plan as part of their bid, they must be approved if they are to be awarded...... a contract, and the competencies of their employees working on the railway are controlled and provided by InfraMan. However, this regime faces a number of further challenges, including uncertainties related to the safety plans, contested responsibility for the education program, difficulties in controlling...

  3. Atomic-scale characterization of hydrogenated amorphous-silicon films and devices. Annual subcontract report, 15 April 1994--14 March 1998

    Energy Technology Data Exchange (ETDEWEB)

    Gallagher, A.; Barzen, S.; Childs, M.; Laracuente, A. [National Inst. of Standards and Technology, Boulder, CO (United States)

    1998-06-01

    The research is concerned with improving the electronic properties of hydrogenated amorphous silicon (a-Si:H) films and of photovoltaic (PV) cells that use these films. Two approaches toward this goal are being taken. One is to establish the character of silicon particle growth in the rf glow discharges that are used to make the films and PV cells, and to understand the particle incorporation into the films. The ultimate goal of this effort is to find mitigation techniques that minimize the particle incorporation. During this contract period the authors have developed a novel particle light-scattering technique that provides a detailed and sensitive diagnostic of small (8-60 nm diameter) particles suspended in the discharge. The authors have used this to measure the particle growth rates and densities, versus conditions in pure-silane discharges. The second program is directed toward measuring the electronic properties of thin-film PV cells, as a function of depth within the cell. The approach being taken is to use a scanning tunneling microscope (STM) to measure the depth-dependent electronic properties of cross-sectioned PV cells. During the present period, measurements on single and tandem amorphous silicon cells have been carried out. Using STM current-voltage spectroscopy, these measurements distinguish the boundaries between the highly-conducting and intrinsic layers, as well as the chemical potential versus depth in the cell.

  4. Photovoltaic Subcontract Program, FY 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This report summarizes the fiscal year (FY) 1991 (October 1, 1990, through September 30, 1991) progress of the subcontracted photovoltaic (PV) research and development (R D) performed under the Photovoltaic Advanced Research and Development Project at the National Renewable Energy Laboratory (NREL) -- formerly the Solar Energy Research Institute (SERI). The mission of the national PV program is to develop PV technology for large-scale generation of economically competitive electric power in the United States. The technical sections of the report cover the main areas of the subcontract program: the Amorphous Silicon Research Project, Polycrystalline Thin Films, Crystalline Silicon Materials Research, High-Efficiency Concepts, the New Ideas Program, the University Participation Program, and the Photovoltaic Manufacturing Technology (PVMaT) project. Technical summaries of each of the subcontracted programs provide a discussion of approaches, major accomplishments in FY 1991, and future research directions.

  5. Fabrication of stable large-area thin-film CdTe photovoltaic modules. Annual subcontract report, 10 May 1992--9 May 1993

    Energy Technology Data Exchange (ETDEWEB)

    Nolan, J.F.; Meyers, P.V. [Solar Cells, Inc., Toledo, OH (United States)

    1993-08-01

    This report highlights the progress made by Solar Cells, Inc. (SCI), in its program to produce 60-cm {times} 120-cm solar modules based on CdTe films. During the past year, confirmed efficiency has increased to 10.4% (active area) on a 1 cm{sup 2} cell, 9.8% (aperture area) on a 64-cm{sup 2} 8-cell submodule, and 6.6% (total area) on a 7200-cm{sup 2} module. A module measured in-house had a power output of 53 W, for a total-area efficiency of 7.4%. Average efficiency of modules produced is steadily increasing and standard deviation is decreasing; in a limited run of 12 modules, results were 6.3% ({plus_minus} 0.2%). Field testing has begun; a nominal 1-kW array of 24 modules was set up adjacent to SCI`s facilities. Analysis indicates that present modules are limited in efficiency by shunt resistance and optical absorption losses in the glass superstrate. Loss analysis of present devices allows us to project a module efficiency of 11.8%. A third generation deposition method -- atmospheric pressure elemental vapor deposition (APEVD) has been brought on-line and has produced good quality CdTe. In addition, SCI is expanding its proactive safety, health, environmental, and disposal program dealing with issues surrounding cadmium.

  6. A BACTERIA FORAGING ALGORITHM FOR SOLVING INTEGRATED MULTI-PERIOD CELL FORMATION AND SUBCONTRACTING PRODUCTION PLANNING IN A DYNAMIC CELLULAR MANUFACTURING SYSTEM

    Directory of Open Access Journals (Sweden)

    S.H. Tang

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: The bacteria foraging algorithm (BFA is a new computation technique inspired by the social foraging behaviour of Escherichia coli (E. coli bacteria. Since the introduction of the BFA by Kevin M. Passino, there have been many challenges in employing this algorithm to problems other than those for which the algorithm was proposed. This research aims to apply this emerging optimisation algorithm to develop a mixed-integer programming model for designing cellular manufacturing systems (CMSs, and production planning in dynamic environments. In dynamic environments, product mix and part demand vary under multi-period planning horizons. Thus the best-designed cells for one period may not be adequate for subsequent periods, requiring their reconstruction. The advantages of the proposed model are as follows: consideration of batch inter-cell and intra-cell material handling by assuming the sequence of operations, allowing for alternative process plans for part types, and consideration of machine copying, with an emphasis on the effect of trade-offs between production and outsourcing costs. The goal is to minimise the sum of the machines’ constant and variable costs, inter-cell and intra-cell material handling costs, reconstruction costs, partial subcontracting costs, and inventory carrying costs. In addition, a newly-developed BFA-based optimisation algorithm has been compared with the branch and bound algorithm. The results suggest that the proposed algorithm performs better than related works.

    AFRIKAANSE OPSOMMING: Die ‘bacteria foraging algorithm’ (BFA is ‘n berekeningstegniek gebaseeer op die sosiale soekgedrag van Escherichia coli (E. coli bakterieë. Sedert die bekendstelling van BFA was daar talle uitdagings oor toepassings van die algoritme op ander probleme as dié waarvoor dit ontwikkel is. Dié navorsing poog om deur toepassing van die algoritme ‘n gemengde heelgetalprogrammeringmodel te ontwikkel vir die

  7. Novel thin-film CuInSe{sub 2} fabrication. Annual subcontract report, 1 May 1992--31 October 1993

    Energy Technology Data Exchange (ETDEWEB)

    Gabor, A.M.; Hermann, A.M. [Colorado Univ., Boulder, CO (United States)

    1994-08-01

    This report describes work exploring a new technique for the formation of Culn{sub x}Ga{sub 1{minus}x}Se{sub 2} thin films. The cu deposition was separated fro the Ga+In deposition such that precursor films with compositions of either Cu{sub x}Se or (In{sub x}Ga{sub 1{minus}x}){sub 2}Se{sub 3} were formed. These precursors were exposed to either (a) In+Ga+Se or (b) cu+Se at substrate temperatures > 500 C to form Galn{sub x}Ga{sub 1{minus}x}Se{sub 2}. Films made from the Cu{sub x}Se precursors were unexceptional, but films made from the (In{sub x}Ga{sub 1{minus}x}){sub 2}Se{sub 3} precursors were of exceptional smoothness and density. During the period covered in this report, a device made fro one of these films resulted in what, at the time, was the highest total-area efficiency measured for any non-single-crystal, thin-film solar cell, at 15.9%.

  8. Fundamental Research and Development for Improved Crystalline Silicon Solar Cells: Final Subcontract Report, March 2002 - July 2006

    Energy Technology Data Exchange (ETDEWEB)

    Rohatgi, A.

    2007-11-01

    This report summarizes the progress made by Georgia Tech in the 2002-2006 period toward high-efficiency, low-cost crystalline silicon solar cells. This program emphasize fundamental and applied research on commercial substrates and manufacturable technologies. A combination of material characterization, device modeling, technology development, and complete cell fabrication were used to accomplish the goals of this program. This report is divided into five sections that summarize our work on i) PECVD SiN-induced defect passivation (Sections 1 and 2); ii) the effect of material inhomogeneity on the performance of mc-Si solar cells (Section 3); iii) a comparison of light-induced degradation in commercially grown Ga- and B-doped Czochralski Si ingots (Section 4); and iv) the understanding of the formation of high-quality thick-film Ag contacts on high sheet-resistance emitters (Section 5).

  9. Thin-film cadmium telluride photovoltaic cells. Final subcontract report, 1 November 1992--1 January 1994

    Energy Technology Data Exchange (ETDEWEB)

    Compaan, A.D.; Bohn, R.G. [Toledo Univ., OH (United States)

    1994-09-01

    This report describes work to develop and optimize radio-frequency (rf) sputtering for the deposition of thin films of cadmium telluride (CdTe) and related semiconductors for thin-film solar cells. Pulsed laser physical vapor deposition was also used for exploratory work on these materials, especially where alloying or doping are involved, and for the deposition of cadmium chloride layers. The sputtering work utilized a 2-in diameter planar magnetron sputter gun. The film growth rate by rf sputtering was studied as a function of substrate temperature, gas pressure, and rf power. Complete solar cells were fabricated on tin-oxide-coated soda-lime glass substrates. Currently, work is being done to improve the open-circuit voltage by varying the CdTe-based absorber layer, and to improve the short-circuit current by modifying the CdS window layer.

  10. 48 CFR 2019.705-4 - Reviewing the subcontracting plan.

    Science.gov (United States)

    2010-10-01

    ... COMMISSION SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS Subcontracting With Small Business, Small Disadvantaged Business, and Women-Owned Small Business Concerns 2019.705-4 Reviewing the subcontracting...

  11. 48 CFR 319.705-5 - Awards involving subcontracting plans.

    Science.gov (United States)

    2010-10-01

    ... SERVICES SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS Subcontracting With Small Business, Small Disadvantaged Business, and Women-Owned Small Business Concerns 319.705-5 Awards involving subcontracting...

  12. 76 FR 74749 - Small Business Subcontracting

    Science.gov (United States)

    2011-12-01

    ... small business subcontracting plan is required, currently valued above $1.5 million for construction and... contracting officer is responsible for monitoring and evaluating small business subcontracting plan...; ] SMALL BUSINESS ADMINISTRATION 13 CFR Parts 121 and 125 RIN 3245-AG22 Small Business...

  13. 48 CFR 30.607 - Subcontract administration.

    Science.gov (United States)

    2010-10-01

    ... CONTRACTING REQUIREMENTS COST ACCOUNTING STANDARDS ADMINISTRATION CAS Administration 30.607 Subcontract administration. When a negotiated CAS price adjustment or a determination of noncompliance is required at the... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Subcontract...

  14. 78 FR 59798 - Small Business Subcontracting: Correction

    Science.gov (United States)

    2013-09-30

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION 13 CFR Part 125 RIN 3245-AG22 Small Business Subcontracting: Correction AGENCY: U.S. Small..., 2013 (78 FR 42391). The document amended SBA's regulations governing small business subcontracting...

  15. Scheduling and Subcontracting under Parallel Machines

    Institute of Scientific and Technical Information of China (English)

    CHEN Rong-jun; TANG Guo-chun

    2012-01-01

    In this paper,we study a model on joint decisions of scheduling and subcontracting,in which jobs(orders) can be either processed by parallel machines at the manufacturer in-house or subcontracted to a subcontractor.The manufacturer needs to determine which jobs should be produced in-house and which jobs should be subcontracted.Furthermore,it needs to determine a production schedule for jobs to be produced in-house.We discuss five classical scheduling objectives as production costs.For each problem with different objective functions,we give optimality conditions and propose dynamic programming algorithms.

  16. Module process optimization and device efficiency improvement for stable, low-cost, large-area, cadmium telluride-based photovoltaic module production. Annual subcontract report, 1 July 1990--31 December 1991

    Energy Technology Data Exchange (ETDEWEB)

    Albright, S.P.; Ackerman, B.; Chamberlin, R.R.; Jordan, J.F. [Photon Energy, Inc., El Paso, TX (United States)

    1992-04-01

    This report describes work under a three-year phased subcontract to develop CdS/CdTe devices and modules and to further improve the technology base at Photon Energy, Inc. (PEI) to better address the commercialization issues and objectives of the PEI and the US Department of Energy. During this reporting period we (1) achieved efficiencies of 12.7% on small area devices, (2) achieved 1-ft{sup 2} modules with over 8% aperture-area efficiency (and active area efficiencies up to {approximately}10%), (3) tested 4-ft{sup 2} modules at NREL at 23.1 (21.3) watts, normalized (6.3% efficiency), and (4) found no inherent stability problems with CdTe technology during life testing, at both NREL and PEI. 7 refs.

  17. 13 CFR 125.3 - Subcontracting assistance.

    Science.gov (United States)

    2010-01-01

    ... feasible units, as appropriate, to facilitate small business participation; (ii) Conducting market research... attending pre-bid conferences; (iii) Soliciting small business concerns as early in the acquisition process... its subcontracting plan. (e) CMR Responsibilities. Commercial Market Representatives (CMRs) are...

  18. Large-Scale PV Module Manufacturing Using Ultra-Thin Polycrystalline Silicon Solar Cells: Final Subcontract Report, 1 April 2002--28 February 2006

    Energy Technology Data Exchange (ETDEWEB)

    Wohlgemuth, J.; Narayanan, M.

    2006-07-01

    The major objectives of this program were to continue advances of BP Solar polycrystalline silicon manufacturing technology. The Program included work in the following areas. (1) Efforts in the casting area to increase ingot size, improve ingot material quality, and improve handling of silicon feedstock as it is loaded into the casting stations. (2) Developing wire saws to slice 100-..mu..m-thick silicon wafers on 290-..mu..m-centers. (3) Developing equipment for demounting and subsequent handling of very thin silicon wafers. (4) Developing cell processes using 100-..mu..m-thick silicon wafers that produce encapsulated cells with efficiencies of at least 15.4% at an overall yield exceeding 95%. (5) Expanding existing in-line manufacturing data reporting systems to provide active process control. (6) Establishing a 50-MW (annual nominal capacity) green-field Mega-plant factory model template based on this new thin polycrystalline silicon technology. (7) Facilitating an increase in the silicon feedstock industry's production capacity for lower-cost solar-grade silicon feedstock..

  19. Identifying Electronic Properties Relevant to Improving the Performance and Stability of Amorphous Silicon Based Photovoltaic Cells: Final Subcontract Report, 27 November 2002--31 March 2005

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, J. D.

    2005-11-01

    A major effort during this subcontract period has been to evaluate the microcrystalline Si material under development at United Solar Ovonics Corporation (USOC). This material is actually a hydrogenated nanocrystalline form of Si and it will be denoted in this report as nc-Si:H. Second, we continued our studies of the BP Solar high-growth samples. Third, we evaluated amorphous silicon-germanium alloys produced by the hot-wire chemical vapor deposition growth process. This method holds some potential for higher deposition rate Ge alloy materials with good electronic properties. In addition to these three major focus areas, we examined a couple of amorphous germanium (a-Ge:H) samples produced by the ECR method at Iowa State University. Our studies of the electron cyclotron resonance a-Ge:H indicated that the Iowa State a Ge:H material had quite superior electronic properties, both in terms of the drive-level capacitance profiling deduced defect densities, and the transient photocapacitance deduced Urbach energies. Also, we characterized several United Solar a Si:H samples deposited very close to the microcrystalline phase transition. These samples exhibited good electronic properties, with midgap defect densities slightly less than 1 x 1016 cm-3 in the fully light-degraded state.

  20. 48 CFR 1852.219-73 - Small business subcontracting plan.

    Science.gov (United States)

    2010-10-01

    ... Provisions and Clauses 1852.219-73 Small business subcontracting plan. As prescribed in 1819.708-70(a), insert the following provision: Small Business Subcontracting Plan (MAY 1999) (a) This provision is not... contain FAR clause 52.219-9, “Small Business Subcontracting Plan.” The apparent low bidder must submit...

  1. 48 CFR 1052.219-71 - Subcontracting Plan.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Subcontracting Plan. 1052... Subcontracting Plan. As prescribed in DTAR 1019.708-70(b), insert the following provision: Subcontracting Plan (MAR 2002) As part of its initial proposal, each large business offeror must submit a contracting...

  2. 76 FR 61626 - Small Business Subcontracting

    Science.gov (United States)

    2011-10-05

    ... in the base creates the illusion that there are more subcontracting opportunities for small business... to enter into a funds control agreement with a neutral third party if the prime contractor fails to... into a funds control agreement with a neutral third party for the purpose of paying subcontractors...

  3. Photovoltaic Program Branch annual report, FY 1989

    Energy Technology Data Exchange (ETDEWEB)

    Summers, K A [ed.

    1990-03-01

    This report summarizes the progress of the Photovoltaic (PV) Program Branch of the Solar Energy Research Institute (SERI) from October 1, 1988, through September 30, 1989. The branch is responsible for managing the subcontracted portion of SERI's PV Advanced Research and Development Project. In fiscal year (FY) 1989, this included nearly 50 subcontracts, with a total annualized funding of approximately $13.1 million. Approximately two-thirds of the subcontracts were with universities, at a total funding of nearly $4 million. The six technical sections of the report cover the main areas of the subcontracted program: Amorphous Silicon Research, Polycrystalline Thin Films, Crystalline Silicon Materials Research, High-Efficiency Concepts, New Ideas, and University Participation. Technical summaries of each of the subcontracted programs provide a discussion of approaches, major accomplishments in FY 1989, and future research directions. Each report will be cataloged individually.

  4. 2015 Annual Progress Report: DOE Hydrogen and Fuel Cells Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-12-23

    The 2015 Annual Progress Report summarizes fiscal year 2015 activities and accomplishments by projects funded by the DOE Hydrogen and Fuel Cells Program. It covers the program areas of hydrogen production; hydrogen delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes and standards; systems analysis; and market transformation.

  5. Final Report for PV Incubator Subcontract No. NAT-0-99013-01: June 14, 2010 - March 2, 2012

    Energy Technology Data Exchange (ETDEWEB)

    Ghosal, K.

    2012-04-01

    The goal of the subcontract is to scale up Semprius' novel micro-cell based modules to an annualized rate of 500 kW of receivers and 10 kW of modules, in support of the DOE 2020 Sunshot Initiative goals. The statement of work (SOW) was broken up into two Phases. Phase I was directed towards process development efforts towards addressing fundamental manufacturing metrics such as yield, die per wafer, automation and throughput. Phase II objectives are to scale to an annualized production rate of 500 kW of receivers and 10 kW of modules, while improving cell efficiency, module efficiency and transfer yield. Semprius has met all the technical milestones and deliverables for the contract. All subtasks were completed earlier than expected and the results exceeded the technical targets. In particular, 3J cell efficiency of 41.2% exceeded the target of 38%, module efficiency of 28.3% exceeded the target of 28% and transfer yield of 96.4% exceeds the target of 95%, with all tasks completed well ahead of schedule. Also, devices fabricated from 1st use GaAs substrates and substrates with two re-uses have been shown to be identical.

  6. 2013 Annual Progress Report: DOE Hydrogen and Fuel Cells Program

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2013-12-01

    The 2013 Annual Progress Report summarizes fiscal year 2013 activities and accomplishments by projects funded by the DOE Hydrogen Program. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing; technology validation; safety, codes and standards; market transformation; and systems analysis.

  7. 2014 Annual Progress Report: DOE Hydrogen and Fuel Cells Program

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-11-01

    The 2014 Annual Progress Report summarizes fiscal year 2014 activities and accomplishments by projects funded by the DOE Hydrogen Program. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing; technology validation; safety, codes and standards; market transformation; and systems analysis.

  8. 2011 Annual Progress Report: DOE Hydrogen and Fuel Cells Program

    Energy Technology Data Exchange (ETDEWEB)

    Satyapal, Sunita [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2011-11-01

    The 2011 Annual Progress Report summarizes fiscal year 2011 activities and accomplishments by projects funded by the DOE Hydrogen Program. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing; technology validation; safety, codes and standards; education; market transformation; and systems analysis.

  9. Development of high-efficiency, thin-film CdTe solar cells. Final subcontract report, 1 February 1992--30 November 1995

    Energy Technology Data Exchange (ETDEWEB)

    Rohatgi, A.; Chou, H.C.; Kamra, S.; Bhat, A. [Georgia Inst. of Tech., Atlanta, GA (United States)

    1996-01-01

    This report describes work performed by the Georgia Institute of Technology (GIT) to bring the polycrystalline CdTe cell efficiency a step closer to the practically achievable efficiency of 18% through fundamental understanding of detects and loss mechanisms, the role of chemical and heat treatments, and investigation of now process techniques. The objective was addressed by a combination of in-depth characterization, modeling, materials growth, device fabrication, and `transport analyses of Au/Cu/CdTe/CdS/SnO {sub 2} glass front-wall heterojunction solar cells. GiT attempted to understand the loss mechanism(s) in each layer and interface by a step-by-step investigation of this multilayer cell structure. The first step was to understand, quantify, and reduce the reflectance and photocurrent loss in polycrystalline CdTe solar calls. The second step involved the investigation of detects and loss mechanisms associated with the CdTe layer and the CdTe/CdS interface. The third stop was to investigate the effect of chemical and heat treatments on CdTe films and cells. The fourth step was to achieve a better and reliable contact to CdTe solar cells by improving the fundamental understanding. Of the effects of Cu on cell efficiency. Finally, the research involved the investigation of the effect of crystallinity and grain boundaries on Cu incorporation in the CdTe films, including the fabrication of CdTe solar calls with larger CdTe grain size.

  10. Improved Solar Cell Efficiency Through the Use of an Additive Nanostructure-Based Optical Downshifter: Final Subcontract Report, January 28, 2010 -- February 28, 2011

    Energy Technology Data Exchange (ETDEWEB)

    Kurtin, J.

    2011-05-01

    This final report summarizes all SpectraWatt's progress in achieving a boost in solar cell efficiency using an optical downshifter. Spectrawatt's downshifting technology is based on a nanostructured material system which absorbs high energy (short wavelength) light and reemits it at a lower energy (long wavelength) with high efficiency. This system has shown unprecedented performance parameters including near unity quantum yield and high thermal stability.

  11. Thin film cadmium telluride, zinc telluride, and mercury zinc telluride solar cells. Final subcontract report, 1 July 1988--31 December 1991

    Energy Technology Data Exchange (ETDEWEB)

    Chu, T.L. [University of South Florida, Tampa, FL (United States)

    1992-04-01

    This report describes research to demonstrate (1) thin film cadmium telluride solar cells with a quantum efficiency of 75% or higher at 0. 44 {mu}m and a photovoltaic efficiency of 11.5% or greater, and (2) thin film zinc telluride and mercury zinc telluride solar cells with a transparency to sub-band-gap radiation of 65% and a photovoltaic conversion efficiency of 5% and 8%, respectively. Work was directed at (1) depositing transparent conducting semiconductor films by solution growth and metal-organic chemical vapor deposition (MOCVD) technique, (2) depositing CdTe films by close-spaced sublimation (CSS) and MOCVD techniques, (3) preparing and evaluating thin film CdTe solar cells, and (4) preparing and characterizing thin film ZnTe, CD{sub 1-x}Zn{sub 1-x}Te, and Hg{sub 1-x}Zn{sub x}Te solar cells. The deposition of CdS films from aqueous solutions was investigated in detail, and their crystallographic, optical, and electrical properties were characterized. CdTe films were deposited from DMCd and DIPTe at 400{degrees}C using TEGa and AsH{sub 3} as dopants. CdTe films deposited by CSS had significantly better microstructures than those deposited by MOCVD. Deep energy states in CdTe films deposited by CSS and MOCVD were investigated. Thin films of ZnTe, Cd{sub 1- x}Zn{sub x}Te, and Hg{sub 1-x}Zn{sub x}Te were deposited by MOCVD, and their crystallographic, optical, and electrical properties were characterized. 67 refs.

  12. 48 CFR 52.219-9 - Small business subcontracting plan.

    Science.gov (United States)

    2010-10-01

    ... Clauses 52.219-9 Small business subcontracting plan. As prescribed in 19.708(b), insert the following clause: Small Business Subcontracting Plan (OCT 2010) (a) This clause does not apply to small business... business, and women-owned small business concerns. If the offeror is submitting an individual contract...

  13. 48 CFR 852.236-80 - Subcontracts and work coordination.

    Science.gov (United States)

    2010-10-01

    ... coordination. 852.236-80 Section 852.236-80 Federal Acquisition Regulations System DEPARTMENT OF VETERANS....236-80 Subcontracts and work coordination. As prescribed in 836.574, insert the following clause: Subcontracts and Work Coordination (APR 1984) (a) Nothing contained in this contract shall be construed...

  14. 48 CFR 836.574 - Subcontracts and work coordination.

    Science.gov (United States)

    2010-10-01

    ... coordination. 836.574 Section 836.574 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS... Subcontracts and work coordination. The contracting officer shall insert the clause at 852.236-80, Subcontracts and work coordination, in solicitations and contracts for construction expected to exceed the...

  15. 48 CFR 970.1907-1 - Subcontracting plan requirements.

    Science.gov (United States)

    2010-10-01

    ... SUPPLEMENTARY REGULATIONS DOE MANAGEMENT AND OPERATING CONTRACTS Small, Small Disadvantaged and Women-Owned Small Business Concerns 970.1907-1 Subcontracting plan requirements. Pursuant to the clause at 48 CFR 52.219-9, Small Business Subcontracting Plan, which is required for all management and...

  16. 48 CFR 970.5227-6 - Patent indemnity-subcontracts.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Patent indemnity... for Management and Operating Contracts 970.5227-6 Patent indemnity—subcontracts. Insert the following clause in solicitations and contracts in accordance with 970.2702-3: Patent Indemnity—Subcontracts...

  17. 48 CFR 52.244-6 - Subcontracts for Commercial Items.

    Science.gov (United States)

    2010-10-01

    ... clauses in subcontracts for commercial items: (i) 52.203-13, Contractor Code of Business Ethics and... Recovery Act. (iii) 52.219-8, Utilization of Small Business Concerns (MAY 2004) (15 U.S.C. 637(d)(2) and (3... subcontracts to small business concerns) exceeds $650,000 ($1.5 million for construction of any public...

  18. An inverted AlGaAs/GaAs patterned-Ge tunnel junction cascade concentrator solar cell. Final subcontract report, 1 January 1991--31 August 1992

    Energy Technology Data Exchange (ETDEWEB)

    Venkatasubramanian, R. [Research Triangle Inst., Research Triangle Park, NC (United States)

    1993-01-01

    This report describes work to develop inverted-grown Al{sub 0.34}Ga{sub 0.66}As/GaAs cascades. Several significant developments are reported on as follows: (1) The AM1.5 1-sun total-area efficiency of the top Al{sub 0.34}Ga{sub 0.66}As cell for the cascade was improved from 11.3% to 13.2% (NREL measurement [total-area]). (2) The ``cycled`` organometallic vapor phase epitaxy growth (OMVPE) was studied in detail utilizing a combination of characterization techniques including Hall-data, photoluminescence, and secondary ion mass spectroscopy. (3) A technique called eutectic-metal-bonding (EMB) was developed by strain-free mounting of thin GaAs-AlGaAs films (based on lattice-matched growth on Ge substrates and selective plasma etching of Ge substrates) onto Si carrier substrates. Minority-carrier lifetime in an EMB GaAs double-heterostructure was measured as high as 103 nsec, the highest lifetime report for a freestanding GaAs thin film. (4) A thin-film, inverted-grown GaAs cell with a 1-sun AM1.5 active-area efficiency of 20.3% was obtained. This cell was eutectic-metal-bonded onto Si. (5) A thin-film inverted-grown, Al{sub 0.34}Ga{sub 0.66}As/GaAs cascade with AM1.5 efficiency of 19.9% and 21% at 1-sun and 7-suns, respectively, was obtained. This represents an important milestone in the development of an AlGaAs/GaAs cascade by OMVPE utilizing a tunnel interconnect and demonstrates a proof-of-concept for the inverted-growth approach.

  19. 75 FR 65439 - Defense Federal Acquisition Regulation Supplement; Electronic Subcontracting Reporting System

    Science.gov (United States)

    2010-10-25

    ... Supplement; Electronic Subcontracting Reporting System AGENCY: Defense Acquisition Regulations System... Electronic Subcontracting Reporting System (eSRS). The FAR has been revised to reflect use of the eSRS...--Summary Subcontract Report, for submission of small business subcontract reports. DATES: Effective...

  20. 75 FR 9604 - Federal Acquisition Regulation; Submission for OMB Review; Subcontracting Plans/Individual...

    Science.gov (United States)

    2010-03-03

    ... subcontracting plans/individual subcontract report. A request for public comments published in the Federal Register at 73 FR 21779 on April 22, 2008. No comments were received. Public comments are particularly... Regulation; Submission for OMB Review; Subcontracting Plans/Individual Subcontract Report...

  1. 48 CFR 19.705-5 - Awards involving subcontracting plans.

    Science.gov (United States)

    2010-10-01

    ... REGULATION SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS The Small Business Subcontracting Program 19.705-5... submit advisory recommendations to the contracting officer. Failure of the representative to respond in...

  2. 48 CFR 19.705-4 - Reviewing the subcontracting plan.

    Science.gov (United States)

    2010-10-01

    ... business concerns as prime contractors or subcontractors in similar acquisitions; (2) Proven methods of involving small business concerns as subcontractors in similar acquisitions; and (3) The relative success of... REGULATION SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS The Small Business Subcontracting Program...

  3. 77 FR 56709 - Proposed Information Collection (VA Subcontracting Report for Service Disabled Veteran-Owned...

    Science.gov (United States)

    2012-09-13

    ... needed to collect information from subcontractors to compare information obtained from subcontracting...) ways to enhance the quality, utility, and clarity of the information to be collected; and (4) ways to... collect information from subcontractors to compare information obtained from subcontracting...

  4. The nexus between OSH and subcontracting.

    Science.gov (United States)

    Nunes, Isabel L

    2012-01-01

    Subcontracting of specialized functions to external companies (e.g. cleaning or maintenance) is actually very common within several industries. These external companies' are called contractors and their contracting is often designated as outsourcing. Frequently contractors involve other companies (the sub-contractors) to assist them in fulfilling the contract, resulting in a complex chain of organizations focused on interchange of work - the contracting chain. Therefore in the same work site can coexist workers form the client-company and workers from the contractors and/or subcontractors. Since contractors perform their job in client's facilities, they can be exposed to hazards that are unknown to them. On other hand, workers of the client company can also be exposed to hazardous situations derived from the work performed by the contractors. The paper discusses how adequate occupational safety and health conditions can be assured when dealing with this kind of dynamic labor networks. Two case-studies and several examples coming from international literature will be presented.

  5. 48 CFR 252.219-7004 - Small business subcontracting plan (test program).

    Science.gov (United States)

    2010-10-01

    ... AND CONTRACT CLAUSES Text of Provisions And Clauses 252.219-7004 Small business subcontracting plan... contract or subcontract. (b) The Offeror's comprehensive small business subcontracting plan and its... “Utilization of Small Business Concerns,” or (2) an approved plan required by this clause, shall be a...

  6. 48 CFR 852.219-9 - VA Small business subcontracting plan minimum requirements.

    Science.gov (United States)

    2010-10-01

    ... Provisions and Clauses 852.219-9 VA Small business subcontracting plan minimum requirements. As prescribed in subpart 819.709, insert the following clause: VA Small Business Subcontracting Plan Minimum Requirements... plan, the minimum goals for award of subcontracts to service-disabled veteran-owned small...

  7. 48 CFR 2452.219-70 - Small business subcontracting plan compliance.

    Science.gov (United States)

    2010-10-01

    ... of Provisions and Clauses 2452.219-70 Small business subcontracting plan compliance. As prescribed in 2419.708(d), insert the following provision: Small Business Subcontracting Plan Compliance (FEB 2006... the clause at FAR 52.219-9, Small Business Subcontracting Plan. (c) The government will...

  8. 77 FR 69626 - Federal Acquisition Regulation; Information Collection; Subcontracting Plans/Individual...

    Science.gov (United States)

    2012-11-20

    ... regarding an extension to this clearance published in the Federal Register at 75 FR 9604, on March 3, 2010... Regulation; Information Collection; Subcontracting Plans/Individual Subcontract Report (SF-294) AGENCIES... previously approved information collection requirement concerning subcontracting plans/individual...

  9. 48 CFR 652.219-70 - Department of State Subcontracting Goals.

    Science.gov (United States)

    2010-10-01

    ... Subcontracting Goals. 652.219-70 Section 652.219-70 Federal Acquisition Regulations System DEPARTMENT OF STATE... Department of State Subcontracting Goals. As prescribed in 619.708-70, insert a provision substantially the same as follows: Department of State Subcontracting Goals (APR 2004) (a) The offeror shall provide...

  10. 48 CFR 552.219-72 - Preparation, Submission, and Negotiation of Subcontracting Plans.

    Science.gov (United States)

    2010-10-01

    ..., and Negotiation of Subcontracting Plans. 552.219-72 Section 552.219-72 Federal Acquisition Regulations... Text of Provisions and Clauses 552.219-72 Preparation, Submission, and Negotiation of Subcontracting... Negotiation of Subcontracting Plans (JUN 2005) (a) An offeror, other than a small business concern,...

  11. 25 CFR 276.16 - Subgrants and subcontracts to non-profit organizations.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Subgrants and subcontracts to non-profit organizations... Subgrants and subcontracts to non-profit organizations. The uniform administrative requirements in this part... subgrants or subcontracts made to non-profit organizations....

  12. 48 CFR 52.219-16 - Liquidated Damages-Subcontracting Plan.

    Science.gov (United States)

    2010-10-01

    ... clause in this contract entitled “Small Business Subcontracting Plan,” or willful or intentional action... contract entitled “Small Business Subcontracting Plan,” the Contractor shall pay the Government liquidated... following clause: Liquidated Damages—Subcontracting Plan (JAN 1999) (a) Failure to make a good faith...

  13. Forecast of contracting and subcontracting opportunities: Fiscal year 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-01-01

    This report describes procurement procedures and opportunities for small businesses with the Department of Energy (DOE). It describes both prime and subcontracting opportunities of $100,000 and above which are being set aside for 8(a) and other small business concerns. The report contains sections on: SIC codes; procurement opportunities with headquarters offices; procurement opportunities with field offices; subcontracting opportunities with major contractors; 8(a) contracts expiring in FY 1998; other opportunities to do business with DOE; management and operating contractors--expiration dates; Office of Small and Disadvantaged Business Utilization (OSDBU) staff directory; and small business survey. This document will be updated quarterly on the home page.

  14. The NASA Plan: To award eight percent of prime and subcontracts to socially and economically disadvantaged businesses

    Science.gov (United States)

    1990-01-01

    It is NASA's intent to provide small disadvantaged businesses, including women-owned, historically black colleges and universities and minority education institutions the maximum practicable opportunity to receive a fair proportion of NASA prime and subcontracted awards. Annually, NASA will establish socioeconomic procurement goals including small disadvantaged business goals, with a target of reaching the eight percent level by the end of FY 1994. The NASA Associate Administrators, who are responsible for the programs at the various NASA Centers, will be held accountable for full implementation of the socioeconomic procurement plans. Various aspects of this plan, including its history, are discussed.

  15. Formal sector subcontracting and informal sector employment in Indian manufacturing

    NARCIS (Netherlands)

    Moreno-Monroy, A.I.; Pieters, J.; Erumban, A.A.

    2014-01-01

    Using nationally representative survey dta of Indian manufacturing enterprises spanning the period 1995-2006, we analyze the link between formal sector subcontracting and informal sector employment. A novelty in our analysis is that this relationship is allowed to differ between modern and tradition

  16. 48 CFR 941.201-71 - Use of subcontracts.

    Science.gov (United States)

    2010-10-01

    ... CATEGORIES OF CONTRACTING ACQUISITION OF UTILITY SERVICES Acquiring Utility Services 941.201-71 Use of... and/or sewerage at facilities owned or leased by DOE shall not be acquired under a subcontract arrangement, except as provided for at 970.4102-1 or if the prime contract is with a utility company....

  17. 40 CFR 35.938-9 - Subcontracts under construction contracts.

    Science.gov (United States)

    2010-07-01

    ... contracts. 35.938-9 Section 35.938-9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND... Water Act § 35.938-9 Subcontracts under construction contracts. (a) The award or execution of... prime contractor under a formally advertised, competitively bid, fixed price construction...

  18. 48 CFR 2019.705 - Responsibilities of the contracting officer under the subcontracting assistance program.

    Science.gov (United States)

    2010-10-01

    ... Regulations System NUCLEAR REGULATORY COMMISSION SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS Subcontracting With Small Business, Small Disadvantaged Business, and Women-Owned Small Business Concerns...

  19. 48 CFR 319.705 - Responsibilities of the Contracting Officer under the subcontracting assistance program.

    Science.gov (United States)

    2010-10-01

    ... Regulations System HEALTH AND HUMAN SERVICES SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS Subcontracting With Small Business, Small Disadvantaged Business, and Women-Owned Small Business Concerns...

  20. 2014 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-10-01

    This report summarizes comments from the Peer Review Panel at the 2014 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on June 16-20, 2014, in Washington, DC. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; market transformation; and systems analysis.

  1. 2013 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2013-10-01

    This report summarizes comments from the Peer Review Panel at the 2013 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on May 13-17, 2013, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; market transformation; and systems analysis.

  2. 2011 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2011-09-01

    This report summarizes comments from the Peer Review Panel at the 2011 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on May 9-13, 2011, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; education; market transformation; and systems analysis.

  3. 2015 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2015-10-01

    This report summarizes comments from the Peer Review Panel at the 2015 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on June 8-12, 2015, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; market transformation; and systems analysis.

  4. 2012 DOE Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2012-09-01

    This report summarizes comments from the Peer Review Panel at the 2012 DOE Hydrogen and Fuel Cells Program Annual Merit Review, held on May 14-18, 2012, in Arlington, Virginia. It covers the program areas of hydrogen production and delivery; hydrogen storage; fuel cells; manufacturing R&D; technology validation; safety, codes, and standards; education; market transformation; and systems analysis.

  5. Ultra-High-Efficiency Multijunction Cell and Receiver Module, Phase 1B: High Performance PV Exploring and Accelerating Ultimate Pathways; Final Subcontract Report, 13 May 2005 - 10 December 2008

    Energy Technology Data Exchange (ETDEWEB)

    King, R. R.

    2010-03-01

    Spectrolab's two High Performance Photovoltaics primary objectives: (1) develop ultra-high-efficiency concentrator multijunction cells and (2) develop a robust concentrator cell receiver package.

  6. 48 CFR 1519.705-70 - Synopsis of contracts containing Pub. L. 95-507 subcontracting plans and goals.

    Science.gov (United States)

    2010-10-01

    ... containing Pub. L. 95-507 subcontracting plans and goals. 1519.705-70 Section 1519.705-70 Federal Acquisition... containing Pub. L. 95-507 subcontracting plans and goals. The synopsis of contract award, where applicable... and goals....

  7. EFG Technology and Diagnostic R&D for Large-Scale PV Manufacturing; Final Subcontract Report, 1 March 2002 - 31 March 2005

    Energy Technology Data Exchange (ETDEWEB)

    Kalejs, J.; Aurora, P.; Bathey, B.; Cao, J.; Doedderlein, J.; Gonsiorawski, R.; Heath, B.; Kubasti, J.; Mackintosh, B.; Ouellette, M.; Rosenblum, M.; Southimath, S.; Xavier, G.

    2005-10-01

    The objective of this subcontract was to carry out R&D to advance the technology, processes, and performance of RWE Schott-Solar's wafer, cell, and module manufacturing lines, and help configure these lines for scaling up of edge-defined, film-fed growth (EFG) ribbon technology to the 50-100 MW PV factory level. EFG ribbon manufacturing continued to expand during this subcontract period and now has reached a capacity of 40 MW. EFG wafer products were diversified over this time period. In addition to 10 cm x 10 cm and 10 cm x 15 cm wafer areas, which were the standard products at the beginning of this program, R&D has focused on new EFG technology to extend production to 12.5 cm x 12.5 cm EFG wafers. Cell and module production also has continued to expand in Billerica. A new 12-MW cell line was installed and brought on line in 2003. R&D on this subcontract improved cell yield and throughput, and optimized the cell performance, with special emphasis on work to speed up wafer transfer, hence enhancing throughput. Improvements of wafer transfer processes during this program have raised cell line capacity from 12 MW to over 18 MW. Optimization of module manufacturing processes was carried out on new equipment installed during a manufacturing upgrade in Billerica to a 12-MW capacity to improve yield and reliability of products.

  8. International Society for Cell and Gene Therapy of Cancer 2009 Annual Meeting held in Cork, Ireland.

    Science.gov (United States)

    Guinn, Barbara; Casey, Garrett; Möller, Mecker G; Kasahara, Noriyuki; O'Sullivan, Gerald C; Peng, Kah-Whye; Tangney, Mark

    2010-01-01

    The International Society for Cell and Gene Therapy (ISCGT) of Cancer annual meeting was held from September 2 through September 4, 2009, in Cork, Ireland ( www.iscgt2009.com ). The conference was held in conjunction with the Irish Society for Gene and Cell Therapy third annual meeting, and brought together scientists and clinicians from around the world in a country developing its knowledge economy. Next year's ISCGT meeting will be held in Doha, the capital of Qatar ( www.iscgt.net ), from September 27 through September 29, 2010.

  9. 48 CFR 3419.705-2 - Determining the need for a subcontracting plan.

    Science.gov (United States)

    2010-10-01

    ... subcontracting plan. 3419.705-2 Section 3419.705-2 Federal Acquisition Regulations System DEPARTMENT OF EDUCATION ACQUISITION REGULATION SOCIOECONOMIC PROGRAMS SMALL BUSINESS AND SMALL DISADVANTAGED BUSINESS CONCERNS Subcontracting With Small Business and Small Disadvantaged Business Concerns 3419.705-2 Determining the need...

  10. Tri-State Synfuels Project Review: Volume 9A. Subcontract information. [Proposed Henderson, Kentucky coal to gasoline plant; water supply and civil engineering subcontracts

    Energy Technology Data Exchange (ETDEWEB)

    1982-06-01

    Volume 9A considers subcontract work done at the site involving hydrogeological studies with respect to water supply and geotechnical work with respect to the building foundations necessary based on boreholes drilled and the lithology of the area. (LTN)

  11. Proceedings of the third annual fuel cells contractors review meeting

    Energy Technology Data Exchange (ETDEWEB)

    Huber, W.J. (ed.)

    1991-06-01

    The overall objective of this program is to develop the essential technology for private sector characterization of the various fuel cell electrical generation systems. These systems promise high fuel to electricity efficiencies (40 to 60 percent), distinct possibilities for cogeneration applications, modularity of design, possibilities of urban siting, and environmentally benign emissions. The purpose of this meeting was to provide the research and development (R D) participants in the DOE/Fossil Energy-sponsored Fuel Cells Program with the opportunity to present key results of their research and to establish closer business contacts. Major emphasis was on phosphoric acid, molten carbonate, and solid oxide technology efforts. Research results of the coal gasification and gas stream cleanup R D activities pertinent to the Fuel Cells Program were also highlighted. Two hundred seventeen attendees from industry, utilities, academia, and Government participated in this 2-day meeting. Twenty-three papers were given in three formal sessions: molten carbonate fuel cells R D (9 papers), solid oxide fuel cells (8 papers), phosphoric acid fuel cells R D (6 papers). In addition to the papers and presentations, these proceedings also include comments on the Fuel Cells Program from the viewpoint of DOE/METC Fuel Cell Overview by Rita A. Bajura, DOE/METC Perspective by Manville J. Mayfield, Electric Power Research Institute by Daniel M. Rastler, Natural Gas by Hugh D. Guthrie, and Transportation Applications by Pandit G. Patil.

  12. Forecast of contracting and subcontracting opportunities. Fiscal year 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    This forecast of prime and subcontracting opportunities with the U.S. Department of Energy and its MAO contractors and environmental restoration and waste management contractors, is the Department`s best estimate of small, small disadvantaged and women-owned small business procurement opportunities for fiscal year 1996. The information contained in the forecast is published in accordance with Public Law 100-656. It is not an invitation for bids, a request for proposals, or a commitment by DOE to purchase products or services. Each procurement opportunity is based on the best information available at the time of publication and may be revised or cancelled.

  13. Annual Report: Advanced Energy Systems Fuel Cells (30 September 2013)

    Energy Technology Data Exchange (ETDEWEB)

    Gerdes, Kirk; Richards, George

    2014-04-16

    The comprehensive research plan for Fuel Cells focused on Solid State Energy Conversion Alliance (SECA) programmatic targets and included objectives in two primary and focused areas: (1) investigation of degradation modes exhibited by the anode/electrolyte/cathode (AEC), development of computational models describing the associated degradation rates, and generation of a modeling tool predicting long term AEC degradation response; and (2) generation of novel electrode materials and microstructures and implementation of the improved electrode technology to enhance performance. In these areas, the National Energy Technology Laboratory (NETL) Regional University Alliance (RUA) team has completed and reported research that is significant to the SECA program, and SECA continued to engage all SECA core and SECA industry teams. Examination of degradation in an operational solid oxide fuel cell (SOFC) requires a logical organization of research effort into activities such as fundamental data gathering, tool development, theoretical framework construction, computational modeling, and experimental data collection and validation. Discrete research activity in each of these categories was completed throughout the year and documented in quarterly reports, and researchers established a framework to assemble component research activities into a single operational modeling tool. The modeling framework describes a scheme for categorizing the component processes affecting the temporal evolution of cell performance, and provides a taxonomical structure of known degradation processes. The framework is an organizational tool that can be populated by existing studies, new research completed in conjunction with SECA, or independently obtained. The Fuel Cell Team also leveraged multiple tools to create cell performance and degradation predictions that illustrate the combined utility of the discrete modeling activity. Researchers first generated 800 continuous hours of SOFC experimental

  14. 2015 Annual Progress Report: DOE Hydrogen and Fuel Cells Program

    Energy Technology Data Exchange (ETDEWEB)

    Popovich, Neil

    2015-12-01

    In the past year, the DOE Hydrogen Program (the Program) made substantial progress toward its goals and objectives. The Program has conducted comprehensive and focused efforts to enable the widespread commercialization of hydrogen and fuel cell technologies in diverse sectors of the economy. With emphasis on applications that will effectively strengthen our nation's energy security and improve our stewardship of the environment, the Program engages in research, development, and demonstration of critical improvements in the technologies. Highlights of the Program's accomplishments can be found in the sub-program chapters of this report.

  15. 2016 Annual Progress Report: DOE Hydrogen and Fuel Cells Program

    Energy Technology Data Exchange (ETDEWEB)

    Satyapal, Sunita [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-02-01

    In the past year, the DOE Hydrogen Program (the Program) made substantial progress toward its goals and objectives. The Program has conducted comprehensive and focused efforts to enable the widespread commercialization of hydrogen and fuel cell technologies in diverse sectors of the economy. With emphasis on applications that will effectively strengthen our nation's energy security and improve our stewardship of the environment, the Program engages in research, development, and demonstration of critical improvements in the technologies. Highlights of the Program's accomplishments can be found in the sub-program chapters of this report.

  16. 2012 Annual Progress Report: DOE Hydrogen and Fuel Cells Program

    Energy Technology Data Exchange (ETDEWEB)

    2012-12-01

    In the past year, the DOE Hydrogen Program (the Program) made substantial progress toward its goals and objectives. The Program has conducted comprehensive and focused efforts to enable the widespread commercialization of hydrogen and fuel cell technologies in diverse sectors of the economy. With emphasis on applications that will effectively strengthen our nation's energy security and improve our stewardship of the environment, the Program engages in research, development, and demonstration of critical improvements in the technologies. Highlights of the Program's accomplishments can be found in the sub-program chapters of this report.

  17. Device physics of thin-film polycrystalline cells and modules: Phase 1 annual report: February 1998--January 1999

    Energy Technology Data Exchange (ETDEWEB)

    Sites, J. R.

    1999-12-21

    This report describes work done by Colorado State University (CSU) during Phase 1 of this subcontract. CSU researchers continued to make basic measurements on CI(G)S and CdTe solar cells fabricated at different labs, to quantitatively deduce the loss mechanisms in these cells, and to make appropriate comparisons that illuminate where progress is being made. Cells evaluated included the new record CIGS cell, CIS cells made with and without CdS, and those made by electrodeposition and electroless growth from solution. Work on the role of impurities focused on sodium in CIS. Cells with varying amounts of sodium added during CIS deposition were fabricated at NREL using four types of substrates. The best performance was achieved with 10{sup {minus}2}--10{sup {minus}1} at% sodium, and the relative merits of proposed mechanisms for the sodium effect were compared. Researchers also worked on the construction and testing of a fine-focused laser-beam apparatus to measure local variations in polycrystalline cell performance. A 1{micro}m spot was achieved, spatial reproducibility in one and two dimensions is less than 1 {micro}m, and photocurrent is reliably measured when the 1{micro}m spot is reduced as low as 1-sun in intensity. In elevated-temperature stress tests, typical CdTe cells held at 100 C under illumination and normal resistive loads for extended periods of time were generally very stable; but those held under reverse or large forward bias and those contacted using larger amounts of copper were somewhat less stable. CdTe cell modeling produced reasonable fits to experimental data, including variations in back-contact barriers. A major challenge being addressed is the photovoltaic response of a single simple-geometry crystallite with realistic grain boundaries.

  18. Advanced processing technology for high-efficiency, thin-film CuInSe{sub 2} and CdTe solar cells. Final subcontract report, March 1, 1992--April 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Morel, D L; Ferekides, C S [University of South Florida, Tampa, FL (United States)

    1996-01-01

    This report describes work performed by the University of South Florida to develop a manufacturing-friendly fabrication process for CuInSe{sub 2} (CIS) solar cells. The process developed under this project uses conventional deposition processes and equipment, does not require stringent process control, and uses elemental Se as the selenium source. The authors believe it can be readily scaled up using off-the-shelf processing equipment and that it will meet the low manufacturing-cost objectives. Another significant achievement under this project was the development of a reactive sputtering deposition technology for ZnO. ZnO is used in many solar cell devices, and sputtering is a desirable manufacturing technology. The application of sputtering has been limited because conventional deposition uses ceramic targets that result in low sputtering rates. The use of Zn metal as the target in reactive sputtering overcomes this limitation. The authors have demonstrated that ZnO deposited by reactive sputtering has state-of-the-art opto-electronic properties. These developments result in large-area uniformity and optimized performance and provide a significant opportunity for applying and commercializing the technology. The second objective of this project was to fabricate high-efficiency CdTe solar cells using manufacturing-friendly processes. Three deposition processes were used to deposit CdS films: chemical bath deposition, rf sputtering, and close-spaced sublimation (CSS). The CdTe films were deposited by CSS. A cell with a record efficiency of 15.8% was obtained.

  19. Forecast of Contracting and Subcontracting Opportunities, Fiscal year 1995

    Energy Technology Data Exchange (ETDEWEB)

    1995-02-01

    Welcome to the US Department of Energy`s Forecast of Contracting and Subcontracting Opportunities. This forecast, which is published pursuant to Public Low 100--656, ``Business Opportunity Development Reform Act of 1988,`` is intended to inform small business concerns, including those owned and controlled by socially and economically disadvantaged individuals, and women-owned small business concerns, of the anticipated fiscal year 1995 contracting and subcontracting opportunities with the Department of Energy and its management and operating contractors and environmental restoration and waste management contractors. This document will provide the small business contractor with advance notice of the Department`s procurement plans as they pertain to small, small disadvantaged and women-owned small business concerns.Opportunities contained in the forecast support the mission of the Department, to serve as advocate for the notion`s energy production, regulation, demonstration, conservation, reserve maintenance, nuclear weapons and defense research, development and testing, when it is a national priority. The Department`s responsibilities include long-term, high-risk research and development of energy technology, the marketing of Federal power, and maintenance of a central energy data collection and analysis program. A key mission for the Department is to identify and reduce risks, as well as manage waste at more than 100 sites in 34 states and territories, where nuclear energy or weapons research and production resulted in radioactive, hazardous, and mixed waste contamination. Each fiscal year, the Department establishes contracting goals to increase contracts to small business concerns and meet our mission objectives.

  20. Formal sector subcontracting and informal sector employment in Indian manufacturing: Author

    OpenAIRE

    2014-01-01

    Using nationally representative survey data of Indian manufacturing enterprises spanning the period 1995–2006, we analyze the link between formal sector subcontracting and informal sector employment. A novelty in our analysis is that this relationship is allowed to differ between modern and traditional segments of the informal sector. We show that formal sector subcontracting is positively related to employment growth only in the most modern segments of the informal sector. Increased subcontr...

  1. Final Report: Sintered CZTS Nanoparticle Solar Cells on Metal Foil; July 26, 2011 - July 25, 2012

    Energy Technology Data Exchange (ETDEWEB)

    Leidholm, C.; Hotz, C.; Breeze, A.; Sunderland, C.; Ki, W.; Zehnder, D.

    2012-09-01

    This is the final report covering 12 months of this subcontract for research on high-efficiency copper zinc tin sulfide (CZTS)-based thin-film solar cells on flexible metal foil. Each of the first three quarters of the subcontract has been detailed in quarterly reports. In this final report highlights of the first three quarters will be provided and details will be given of the final quarter of the subcontract.

  2. Remedial action plan and site design for stabilization of the inactive uranium mill tailings site at Tuba City, Arizona: Phase 2, Construction, Subcontract documents: Appendix E, final report. [Uranium Mill Tailings Remedial Action (UMTRA) Project

    Energy Technology Data Exchange (ETDEWEB)

    1989-08-01

    This appendix discusses Phase II construction and subcontract documents uranium mill site near Tuba City, Arizona. It contains the bid schedule, special conditions, specifications, and subcontract drawings.

  3. Fuel cells for transportation program: FY1997 national laboratory annual report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The Department of Energy (DOE) Fuel Cells for Transportation Program is structured to effectively implement the research and development (R and D) required for highly efficient, low or zero emission fuel cell power systems to be a viable replacement for the internal combustion engine in automobiles. The Program is part of the Partnership for a New Generation of Vehicles (PNGV), a government-industry initiative aimed at development of an 80 mile-per-gallon vehicle. This Annual Report summarizes the technical accomplishments of the laboratories during 1997. Participants include: Argonne National Laboratory (ANL), Brookhaven National Laboratory (BNL), Lawrence Berkeley National Laboratory (LBNL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), Pacific Northwest National Laboratory (PNNL), and the National Renewable Energy Laboratory (NREL). During 1997, the laboratory R and D included one project on solid oxide fuel cells; this project has since been terminated to focus Department resources on PEM fuel cells. The technical component of this report is divided into five key areas: fuel cell stack research and development; fuel processing; fuel cell modeling, testing, and evaluation; direct methanol PEM fuel cells; and solid oxide fuel cells.

  4. 40 CFR 35.4240 - What provisions must my group's TAG contractor comply with if it subcontracts?

    Science.gov (United States)

    2010-07-01

    ...) Section 35.4235 pertaining to contract provisions; and (h) Cost principles in 48 CFR part 31, the Federal... contractor comply with if it subcontracts? 35.4240 Section 35.4240 Protection of Environment ENVIRONMENTAL... with if it subcontracts? A TAG contractor must comply with the following provisions when...

  5. Estimated average annual rate of change of CD4(+) T-cell counts in patients on combination antiretroviral therapy

    DEFF Research Database (Denmark)

    Mocroft, Amanda; Phillips, Andrew N; Ledergerber, Bruno;

    2010-01-01

    BACKGROUND: Patients receiving combination antiretroviral therapy (cART) might continue treatment with a virologically failing regimen. We sought to identify annual change in CD4(+) T-cell count according to levels of viraemia in patients on cART. METHODS: A total of 111,371 CD4(+) T-cell counts ...

  6. High-efficiency large-area CdTe panels. Final subcontract report, June 1987--July 1990

    Energy Technology Data Exchange (ETDEWEB)

    Albright, S.P.; Chamberlin, R.R.; Jordan, J.F. [Photon Energy, Inc., El Paso, TX (USA)

    1990-11-01

    The objective of this three year effort has been to develop an improved materials technology and fabrication process for limited volume production of 1 ft{sup 2} and 4 ft{sup 2} CdS/CdTe photovoltaic modules. The module stability objective by the end of this three year subcontract was to develop techniques to provide ten year life exploration with no greater than 10% degradation. In order to achieve these efficiency and stability objectives, the research program has been separated into tasks including: (1) analysis and characterization of CdS/CdTe Devices; (2) performance optimization on small cells; (3) encapsulation and stability testing; and (4) module efficiency optimization. 27 refs., 18 figs., 3 tabs.

  7. 8th Annual Glycoscience Symposium: Integrating Models of Plant Cell Wall Structure, Biosynthesis and Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Azadi, Paratoo [Univ. of Georgia, Athens, GA (United States)

    2015-09-24

    The Complex Carbohydrate Research Center (CCRC) of the University of Georgia holds a symposium yearly that highlights a broad range of carbohydrate research topics. The 8th Annual Georgia Glycoscience Symposium entitled “Integrating Models of Plant Cell Wall Structure, Biosynthesis and Assembly” was held on April 7, 2014 at the CCRC. The focus of symposium was on the role of glycans in plant cell wall structure and synthesis. The goal was to have world leaders in conjunction with graduate students, postdoctoral fellows and research scientists to propose the newest plant cell wall models. The symposium program closely followed the DOE’s mission and was specifically designed to highlight chemical and biochemical structures and processes important for the formation and modification of renewable plant cell walls which serve as the basis for biomaterial and biofuels. The symposium was attended by both senior investigators in the field as well as students including a total attendance of 103, which included 80 faculty/research scientists, 11 graduate students and 12 Postdoctoral students.

  8. Four-terminal organic solar cell modules with increased annual energy yield

    Science.gov (United States)

    Gehlhaar, Robert; Cheyns, David; Van Willigenburg, Luuk; Hadipour, Afshin; Gilot, Jan; Radbeh, Roshanak; Aernouts, Tom

    2013-10-01

    The authors present experimental results on mechanically stacked organic solar modules and their advantage over standard tandem architectures. A four-terminal configuration of two single junction modules with complementary absorbing active layers uses the more efficient energy conversion of a tandem structure without the necessity of matching currents or voltages of electrically connected subcells. The presented combination of semitransparent and opaque solar cells consists of solution processed polymer-fullerene blends as active materials. A cost-effective mechanical scribing process is applied for the patterning of the deposited layers. The best devices have an efficiency of over 6.5% on an aperture area of 16 cm2 which equals a gain of 30% over the best single junction module fabricated by the same process. Optical simulations demonstrate a 32% increased annual energy output of a mechanically stacked device in comparison to a monolithic tandem structure using an equivalent geometry.

  9. 48 CFR 252.219-7003 - Small business subcontracting plan (DoD contracts).

    Science.gov (United States)

    2010-10-01

    ... subcontracting goal. (e) A mentor firm, under the Pilot Mentor-Protege Program established under Section 831 of... awarded— (1) Protege firms which are qualified organizations employing the severely handicapped; and (2) Former protege firms that meet the criteria in Section 831(g)(4) of Pub. L. 101-510. (f) The master...

  10. Formal sector subcontracting and informal sector employment in Indian manufacturing : Author

    NARCIS (Netherlands)

    Moreno-Monroy, Ana I; Pieters, Janneke; Erumban, Abdul Azeez

    2014-01-01

    Using nationally representative survey data of Indian manufacturing enterprises spanning the period 1995–2006, we analyze the link between formal sector subcontracting and informal sector employment. A novelty in our analysis is that this relationship is allowed to differ between modern and traditio

  11. 40 CFR 35.937-12 - Subcontracts under subagreements for architectural or engineering services.

    Science.gov (United States)

    2010-07-01

    ... architectural or engineering services. 35.937-12 Section 35.937-12 Protection of Environment ENVIRONMENTAL... Treatment Works-Clean Water Act § 35.937-12 Subcontracts under subagreements for architectural or...) Section 35.937-6 (Cost and price considerations); (6) Section 35.937-7 (Profit); (7) Prohibition...

  12. 78 FR 17668 - Federal Acquisition Regulation; Submission for OMB Review; Subcontracting Plans/Individual...

    Science.gov (United States)

    2013-03-22

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF DEFENSE..., the ISR collects subcontract awards for Historically Black Colleges and Universities and Minority... going down as the Government publishes rule that make the process less complex, more transparent,...

  13. U.S. Department of Energy Hydrogen and Fuel Cells Program 2011 Annual Merit Review and Peer Evaluation Report

    Energy Technology Data Exchange (ETDEWEB)

    Satypal, S.

    2011-09-01

    This document summarizes the comments provided by peer reviewers on hydrogen and fuel cell projects presented at the FY 2011 U.S. Department of Energy (DOE) Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting (AMR), held May 9-13, 2011 in Arlington, Virginia

  14. 42nd Annual Meeting of the American Society for Cell Biology, San Francisco, California, USA, 14–18 December 2002

    OpenAIRE

    Kenny, Paraic A; Rizki, Aylin

    2003-01-01

    The Annual Meeting of the American Society for Cell Biology (ASCB) is a diverse conference covering all topics in cell biology. While all of the basic biology presented at this meeting may potentially contribute to breast cancer research, there were a significant number of presentations and posters directly pertinent to this field. Here we have summarized the research that is of greatest immediate relevance to breast cancer, with particular emphasis on mammary gland development and tumorigene...

  15. Uranium Mill Tailings Remedial Action Project (UMTRAP), Slick Rock, Colorado, Revision 1. Bid schedule, special conditions, specifications, and subcontract drawings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    This volume contains: bidding requirements; terms and conditions; specifications for Division 1 -- general requirements; specifications for Division 2 -- sitework; specifications for Divisions 5 -- metals; subcontract drawings, (general, Union Carbide processing site, North Continent processing site, and Burro Canyon disposal site).

  16. A survey of the literature on challenges to safety posed by outsourcing or subcontracting of critical tasks

    DEFF Research Database (Denmark)

    Thommesen, Jacob; Andersen, Henning Boje; Øien, Knut;

    The purpose of this document is to report on a review of the literature on the relation between safety and outsourcing or subcontracting. The review seeks to identify the problems and solutions that have been identified and described in the literature concerning outsourcing and subcontracting....... The report, being the first of three reports that comprise Deliverable D1.4.1, describes results of an extensive review of the literature that has been referenced in science and engineering databases....

  17. Optimization of Processing and Modeling Issues for Thin-Film Solar Cell Devices; Annual Report, 3 February 1997-2 February 1998

    Energy Technology Data Exchange (ETDEWEB)

    Birkmire, R. W.; Phillips, J. E.; Shafarman, W. N.; Hegedus, S. S.; McCandless, B. E. (IEC, University of Delaware)

    1998-12-08

    This report describes results achieved during phase I of a four-phase subcontract to develop and understand thin-film solar cell technology associated with CuInSe2 and related alloys, a-Si and its alloys, and CdTe. Modules based on all these thin films are promising candidates to meet DOE long-range efficiency, reliability, and manufacturing cost goals. The critical issues being addressed under this program are intended to provide the science and engineering basis for developing viable commercial processes and to improve module performance. The generic research issues addressed are: (1) quantitative analysis of processing steps to provide information for efficient commercial-scale equipment design and operation; (2) device characterization relating the device performance to materials properties and process conditions; (3) development of alloy materials with different bandgaps to allow improved device structures for stability and compatibility with module design; (4) development of improved window/heterojunction layers and contacts to improve device performance and reliability; and (5) evaluation of cell stability with respect to illumination, temperature, and ambient and with respect to device structure and module encapsulation.

  18. The advantages of Low Pressure Carburizing in the Heat Treatment Subcontracting Business

    Institute of Scientific and Technical Information of China (English)

    Guy PRUNEL; Bruno STAUDER

    2004-01-01

    Low Pressure Carburizing (LPC) was introduced in the 90's in the western Europe Heat Treatment business,mainly for in-house applications where it was especially appreciated for carburizing of transmission parts. However the success of the LPC units installed for gears carburizing in the automotive industry has hindered the development of the process in other fields - like subcontracting business -, where its advantages deserve to be enlightened.After a brief review of the principle of the process, the interest of its classical application to transmission parts is described,underlining peculiarly the reduction of the distortion observed when LPC is associated with high pressure gas quenching.Then the less-known advantages of the LPC process, like the high accuracy and reproducibility of the results, the modeling possibility and the simulation easiness, the case-depth uniformity and the full flexibility of the units are considered,showing how they can be beneficial to subcontracting business.

  19. 管庄的土地转包%Subcontract of Land in Guanzhuang Village

    Institute of Scientific and Technical Information of China (English)

    管兵

    2004-01-01

    Through an analysis of the effects of out-for-work in a village in Guanzhuang, a natural village in the southeast of Henan province, the author focuses its study of “Nongmingong” on the sending place, and thinks it meaningful in learning of the process of civilization, although it is less concerned in the current study of “Nongmingong”. The author thinks subcontract of land is the key point to study the effects of out-for-work, and analyzes this issue as following: First, the peasants of Guanzhuang can be divided into three kinds : earthbound peasants, amphibian peasants and earth-free peasants, according to their roles in the practice of subcontract of land .Secondly, nowadays, earth-free peasants play as the main role in the effects of subcontract of land in Guanzhuang.Thirdly, can earth-bound peasants who rent others' land prominently increase their incomes depending on land, can earth-free peasants work more steadily in cities, and what is the future of the amphibian peasants?

  20. U.S. Department of Energy Hydrogen and Fuel Cells Program, 2013 Annual Merit Review and Peer Evaluation Report (Book)

    Energy Technology Data Exchange (ETDEWEB)

    2013-10-01

    The fiscal year (FY) 2013 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting (AMR), in conjunction with DOE's Vehicle Technologies Office AMR, was held from May 13-16, 2013, at the Crystal City Marriott and Crystal Gateway Marriott in Arlington, Virginia. This report is a summary of comments by AMR peer reviewers about the hydrogen and fuel cell projects funded by DOE's Office of Energy Efficiency and Renewable Energy (EERE).

  1. Immunohistochemical study of pituitary cells in wild and captive Salminus hilarii (Characiformes: Characidae) females during the annual reproductive cycle.

    Science.gov (United States)

    Honji, Renato Massaaki; Nóbrega, Rafael Henrique; Pandolfi, Matias; Shimizu, Akio; Borella, Maria Inês; Moreira, Renata Guimarães

    2013-01-01

    Freshwater fish that live exclusively in rivers are at particular risk from fragmentation of the aquatic system, mainly the species that migrate upriver for reproduction. That is the case of Salminus hilarii, an important migratory species currently classified as "almost threatened" in the São Paulo State (Brazil), facing water pollution, dam construction, riparian habitat destruction and environmental changes that are even more serious in this State. Additionally, this species show ovulation dysfunction in captivity. Our studies focused on the identification and distribution of the pituitary cell types in the adenohypophysis of S. hilarii females, including a morphometric analysis that compares pituitary cells from wild and captive broodstocks during the reproductive annual cycle. The morphology of adenohypophysial cells showed differences following the reproductive cycle and the environment. In general, optical density suggested a higher cellular activity during the previtellogenic (growth hormone) and vitellogenic (somatolactin) stages in both environments. Additionally, the nucleus/cell ratio analysis suggested that growth hormone and somatolactin cells were larger in wild than in captive females in most reproductive stages of the annual cycle. In contrast, prolactin hormone showed no variation throughout the reproductive cycle (in both environments). Morphometrical analyses related to reproduction of S. hilarii in different environmental conditions, suggest that somatolactin and growth hormone play an important role in reproduction in teleost and can be responsible for the regulation of associated processes that indirectly affect reproductive status.

  2. Teaching the relation between solar cell efficiency and annual energy yield

    Energy Technology Data Exchange (ETDEWEB)

    Sark, Wilfried G J H M van [Department of Science, Technology and Society, Copernicus Institute for Sustainable Development and Innovation, Utrecht University, Heidelberglaan 2, 3584 CS Utrecht (Netherlands)

    2007-05-16

    To reach a sustainable world the use of renewable energy sources is imperative. Photovoltaics (PV) is but one of the technologies that use the power of the sun and its deployment is growing very fast. Several master programs have been developed over the world, including Utrecht University, that teach these technologies. Within the framework of a course on energy conversion technologies, we have developed a classroom problem that focuses on the difference between PV efficiency and annual yield for the two locations: the Utrecht University campus and the African Sahara desert. In spreadsheet format, students calculate annual yield, and they find a best method to do so. The exercise can be done in about three hours, and students will learn that the annual yield in the Sahara is only twice that at Utrecht University,.

  3. Subcontract 8699K0013-9Q. Final progress report, July 19, 1993--July 18, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Humphries, S. Jr.

    1996-09-30

    A major activity in the subcontract was to provide theoretical and analytical support for experimental activities at Los Alamos National Laboratory. Reflecting changes in the laboratory organization, work was performed initially for Group P-14 and latter for the Agex Program Office. A second task was to develop, to supply and to support software in the areas of hydrodynamics, magnetohydrodynamics and electromagnetics. The programs are compatible with personal computers and allow simulations of experiments by laboratory personnel both on-site and in the field.

  4. U.S. Department of Energy Hydrogen and Fuel Cells Program 2012 Annual Merit Review and Peer Evaluation Report: May 14-18, 2012, Arlington, VA

    Energy Technology Data Exchange (ETDEWEB)

    2012-09-01

    This document summarizes the comments provided by peer reviewers on hydrogen and fuel cell projects presented at the fiscal year (FY) 2012 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting (AMR), held May 14-18, 2012, in Arlington, VA.

  5. Investigation of reliability attributes and accelerated stress factors on terrestrial solar cells. Third annual report

    Energy Technology Data Exchange (ETDEWEB)

    Lathrop, J.W.; Hartman, R.A.; Saylor, C.R.

    1981-01-01

    The third year of the accelerated reliability testing program concentrated on electrical measurement instrumentation and in modeling cell behavior in the second quadrant. In addition, some preliminary work was done on correlating cell color changes with electrical degradation. Not reported are results of continuing accelerated stress tests on state of the art cells. A number of new cells were added to the program, but not in time for sufficient data to be obtained, while the older cells are undergoing extended test periods and new data are not yet available on them. The all-digital, microprocessor controlled, short interval tester, which was designed and fabricated, has replaced the manual measurement procedure formerly used. This has improved measurement accuracy and repeatability, reduced measurement time, and through coordinated data management procedures, eliminated data errors. A complete description of the tester including schematics and software is given and its operating procedures described. A computer model, based on the thermal and electrical properties of the cells and encapsulating materials, was developed to relate cell temperature to electrical characteristics in the second quadrant. This model adequately predicted the behavior of both encapsulated and unencapsulated cells, although accurate temperature measurements on encapsulated cells were difficult to obtain. In addition, only cells of one type were used for comparison and other cell types may require different parameter values for fitting. Use of the model should permit the prediction of a cell's sensitivity to degradation in the second quadrant. The computer program is listed together with a description of its operation.

  6. Wetland Biomass Production: emergent aquatic management options and evaluations. A final subcontract report. [Includes a bibliography containing 686 references on Typha from biological abstracts

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, D.C.; Dubbe, D.R.; Garver, E.G.; Linton, P.J.

    1984-07-01

    The high yield potential and attractive chemical composition of Typha make it a particularly viable energy crop. The Minnesota research effort has demonstrated that total annual biomass yields equivalent to 30 dry tonnes/ha (13 tons/acre) are possible in planted stands. This compares with yields of total plant material between 9 and 16 dry tonnes/ha (4 to 7 tons/acre) in a typical Minnesota corn field. At least 50% of the Typha plant is comprised of a belowground rhizome system containing 40% starch and sugar. This high level of easily fermentable carbohydrate makes rhizomes an attractive feedstock for alcohol production. The aboveground portion of the plant is largely cellulose, and although it is not easily fermentable, it can be gasified or burned. This report is organized in a manner that focuses on the evaluation of the management options task. Results from stand management research performed at the University of Minnesota during 1982 and 1983 are integrated with findings from an extensive survey of relevant emergent aquatic plant research and utilization. These results and findings are then arranged in sections dealing with key steps and issues that need to be dealt with in the development of a managed emergent aquatic bio-energy system. A brief section evaluating the current status of rhizome harvesting is also included along with an indexed bibliography of the biology, ecology, and utilization of Typha which was completed with support from this SERI subcontract. 686 references, 11 figures, 17 tables.

  7. Small Business: Action Needed to Determine Whether DOD’s Comprehensive Subcontracting Plan Test Program Should Be Made Permanent

    Science.gov (United States)

    2015-11-01

    would include contracting officers, small business specialists, and cost analysts —all require specific levels of expertise and training depending... marketing tool to attract small businesses . Because of its large contracting operations, DOD is critical to the success of federal programs designed to...SMALL BUSINESS Action Needed to Determine Whether DOD’s Comprehensive Subcontracting Plan Test Program Should Be

  8. 48 CFR 927.404 - Rights in technical data in subcontracts. (DOE coverage-paragraphs (g), (k), (l), and (m))

    Science.gov (United States)

    2010-10-01

    ... in subcontracts. (DOE coverage-paragraphs (g), (k), (l), and (m)) 927.404 Section 927.404 Federal...—paragraphs (g), (k), (l), and (m)) (g)(4) Contractors are required by paragraph (d)(3) of the clause at FAR... confidentiality, and reasonable royalties, is then left to the negotiation of the parties. (m) Access...

  9. 48 CFR 970.1907 - Subcontracting with Small Business, Small Disadvantaged Business and Woman-Owned Small Business...

    Science.gov (United States)

    2010-10-01

    ... Business, Small Disadvantaged Business and Woman-Owned Small Business Concerns. 970.1907 Section 970.1907... MANAGEMENT AND OPERATING CONTRACTS Small, Small Disadvantaged and Women-Owned Small Business Concerns 970.1907 Subcontracting with Small Business, Small Disadvantaged Business and Woman-Owned Small...

  10. 48 CFR 212.570 - Applicability of certain laws to contracts and subcontracts for the acquisition of commercially...

    Science.gov (United States)

    2010-10-01

    ... laws to contracts and subcontracts for the acquisition of commercially available off-the-shelf items..., DEPARTMENT OF DEFENSE ACQUISITION PLANNING ACQUISITION OF COMMERCIAL ITEMS Applicability of Certain Laws to the Acquisition of Commercial Items 212.570 Applicability of certain laws to contracts...

  11. 24 CFR 964.320 - HUD Policy on training, employment, contracting and subcontracting of public housing residents.

    Science.gov (United States)

    2010-04-01

    ... TENANT OPPORTUNITIES IN PUBLIC HOUSING Family Investment Centers (FIC) Program § 964.320 HUD Policy on... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false HUD Policy on training, employment, contracting and subcontracting of public housing residents. 964.320 Section 964.320 Housing and...

  12. 75 FR 34260 - Federal Acquisition Regulation; FAR Case 2005-040, Electronic Subcontracting Reporting System (eSRS)

    Science.gov (United States)

    2010-06-16

    ... been certified by the Small Business Administration as small disadvantaged businesses), women-owned... certified by the Small Business Administration as small disadvantaged businesses), women-owned small...) and women- owned small business subcontracting data, as specified in part 19: SF 294,......

  13. Lessons learned from the EG&G consolidated hazardous waste subcontract and ESH&Q liability assessment process

    Energy Technology Data Exchange (ETDEWEB)

    Fix, N.J.

    1995-03-01

    Hazardous waste transportation, treatment, recycling, and disposal contracts were first consolidated at the Idaho National Engineering Laboratory in 1992 by EG&G Idaho, Inc. At that time, disposition of Resource, Conservation and Recovery Act hazardous waste, Toxic Substance Control Act waste, Comprehensive Environmental Response, Compensation, and Liability Act hazardous substances and contaminated media, and recyclable hazardous materials was consolidated under five subcontracts. The wastes were generated by five different INEL M&O contractors, under the direction of three different Department of Energy field offices. The consolidated contract reduced the number of facilities handling INEL waste from 27 to 8 qualified treatment, storage, and disposal facilities, with brokers specifically prohibited. This reduced associated transportation costs, amount and cost of contractual paperwork, and environmental liability exposure. EG&G reviewed this approach and proposed a consolidated hazardous waste subcontract be formed for the major EG&G managed DOE sites: INEL, Mound, Rocky Flats, Nevada Test Site, and 10 satellite facilities. After obtaining concurrence from DOE Headquarters, this effort began in March 1992 and was completed with the award of two master task subcontracts in October and November 1993. In addition, the effort included a team to evaluate the apparent awardee`s facilities for environment, safety, health, and quality (ESH&Q) and financial liability status. This report documents the evaluation of the process used to prepare, bid, and award the EG&G consolidated hazardous waste transportation, treatment, recycling, and/or disposal subcontracts and associated ESH&Q and financial liability assessments; document the strengths and weaknesses of the process; and propose improvements that would expedite and enhance the process for other DOE installations that used the process and for the re-bid of the consolidated subcontract, scheduled for 1997.

  14. Fixed-Price Subcontracting for Decontamination and Decommissioning of Small Facilities at Oak Ridge National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Harper, M. A.; Julius, J. F. K.; McKenna, M. K.

    2002-02-26

    Abandoned facilities were decontaminated and decommissioned in preparation for final remediation of Solid Waste Storage Area (SWSA) 4 at Oak Ridge National Laboratory. The facilities varied in age from approximately 5 years to more than 40 years, with radiological conditions ranging from clean to highly contaminated with fission products. A fixed-price subcontract (FPSC) was awarded by the U.S. Department of Energy's (DOE's) Environmental Management (EM) Management and Integration (M&I) contractor for decontamination and decommissioning (D&D) of these facilities. Included in the FPSC scope were the following: preparation of pre-D&D regulatory documentation; demolition of surface structures to slab; stabilization of below-grade structures; waste management and disposal; and preparation of post-D&D regulatory documentation. Using stand-off techniques to the extent possible, building structures and ancillary equipment were prepared for demolition and demolished. A fixative coating system was used in conjunction with continuous water misting to control airborne contamination. Demolition waste consisted of two major streams: clean construction and demolition waste and low-level (radioactive) waste. The debris was size-reduced and packaged, again via remote means. At all times during the D&D, personnel safety, environmental compliance, and as low as reasonably achievable exposure considerations were paramount. Upon completion of D&D activities, each site was inspected and accepted by the M&I contractor. This project is a success story for fixed-price subcontracting of D&D work under DOE's M&I arrangement.

  15. Investigation of reliability attributes and accelerated stress factors of terrestrial solar cells. First annual report

    Energy Technology Data Exchange (ETDEWEB)

    Prince, J.L.; Lathrop, J.W.

    1979-05-01

    The results of accelerated stress testing of four different types of silicon terrestrial solar cells are discussed. The accelerated stress tests used included bias-temperature tests, bias-temperature-humidity tests, thermal cycle and thermal shock tests, and power cycle tests. Characterization of the cells was performed before stress testing and at periodic down-times, using electrical measurement, visual inspection, and metal adherence pull tests. Electrical parameters measured included short-circuit current, I/sub sc/, open circuit voltage, V/sub oc/, and output power, voltage, and current at the maximum power point, P/sub m/, V/sub m/, and I/sub m/ respectively. Incorporated in the report are the distributions of the prestress electrical data for all cell types. Data was also obtained on cell series and shunt resistance. Significant differences in the response to the various stress tests was observed between cell types. On the basis of the experience gained in this research work, a suggested Reliability Qualification Test Schedule was developed.

  16. 2011 Annual Progress Report: DOE Hydrogen and Fuel Cells Program (Book)

    Energy Technology Data Exchange (ETDEWEB)

    2011-11-01

    In the past year, the DOE Hydrogen and Fuel Cells Program (the Program) made substantial progress toward its goals and objectives. The Program has conducted comprehensive and focused efforts to enable the widespread commercialization of hydrogen and fuel cell technologies in diverse sectors of the economy. With emphasis on applications that will effectively strengthen our nation's energy security and improve our stewardship of the environment, the Program engages in research, development, and demonstration of critical improvements in the technologies. Highlights of the Program's accomplishments can be found in the sub-program chapters of this report.

  17. U.S. Department of Energy Hydrogen and Fuel Cells Program 2016 Annual Merit Review and Peer Evaluation Report: June 6-10, 2016, Washington, DC

    Energy Technology Data Exchange (ETDEWEB)

    Popovich, Neil

    2016-10-01

    The fiscal year 2016 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting (AMR), in conjunction with DOE's Vehicle Technologies Office AMR, was held from June 6-10, 2015, in Washington, D.C.. This report is a summary of comments by AMR peer reviewers about the hydrogen and fuel cell projects funded by DOE's Office of Energy Efficiency and Renewable Energy.

  18. U.S. Department of Energy Hydrogen and Fuel Cells Program 2015 Annual Merit Review and Peer Evaluation Report: June 8-12, 2015, Arlington, Virginia

    Energy Technology Data Exchange (ETDEWEB)

    Popovich, Neil

    2015-10-01

    The fiscal year 2015 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting (AMR), in conjunction with DOE's Vehicle Technologies Office AMR, was held from June 8-12, 2015, in Arlington, Virginia. This report is a summary of comments by AMR peer reviewers about the hydrogen and fuel cell projects funded by DOE's Office of Energy Efficiency and Renewable Energy.

  19. Adult stem cells and mammalian epimorphic regeneration-insights from studying annual renewal of deer antlers.

    Science.gov (United States)

    Li, Chunyi; Yang, Fuhe; Sheppard, Allan

    2009-09-01

    Mammalian organ regeneration is the "Holy Grail" of modern regenerative biology and medicine. The most dramatic organ replacement is known as epimorphic regeneration. To date our knowledge of epimorphic regeneration has come from studies of amphibians. Notably, these animals have the ability to reprogram phenotypically committed cells at the amputation plane toward an embryonic-like cell phenotype (dedifferentiation). The capability of mammals to initiate analogous regeneration, and whether similar mechanisms would be involved if it were to occur, remain unclear. Deer antlers are the only mammalian appendages capable of full renewal, and therefore offer a unique opportunity to explore how nature has solved the problem of mammalian epimorphic regeneration. Following casting of old hard antlers, new antlers regenerate from permanent bony protuberances, known as pedicles. Studies through morphological and histological examinations, tissue deletion and transplantation, and cellular and molecular techniques have demonstrated that antler renewal is markedly different from that of amphibian limb regeneration (dedifferentiation-based), being a stem cell-based epimorphic process. Antler stem cells reside in the pedicle periosteum. We envisage that epimorphic regeneration of mammalian appendages, other than antler, could be made possible by recreating comparable milieu to that which supports the elaboration of that structure from the pedicle periosteum.

  20. Annual Report for Gravity Collection Lysimeter Monitoring Plan – ERDF Cells 5 and 6

    Energy Technology Data Exchange (ETDEWEB)

    M. L. Proctor

    2006-04-04

    The data and analyses contained in this report reflect the initial characterization of construction and consolidation water in Cells 5 and 6 lysimeters. Therefore, the scope of this report will be to establish constituent levels and document dewatering activities completed to date.

  1. Overcoming degradation mechanisms in CdTe solar cells: First annual report, August 1998--August 1999

    Energy Technology Data Exchange (ETDEWEB)

    Cahen, D.; Gartsman, K.; Hodes, G.; Rotlevy, O.; Visoly-Fisher, I,; Dobson, K.

    2000-02-28

    The authors have studied the importance of chemical processes for the stability of CdTe solar cells, in particular, diffusion in the ohmic contact/absorber junction regions. Both whole cells and test systems containing only the ohmic contact and the absorber are used. They found several experimental methods to be useable tools to follow the effects of impurity diffusion on the CdTe grain boundaries, grain bulk, and surface. In addition, they have explored alternative contacting schemes. The first year of activities led to the following tentative conclusions: Grain boundaries in CdTe/CdS cells are NOT fully passivated and are expected to be electrically active; There appears to be fast ionic diffusion in the vicinity of the Cu/HgTe/graphite back-contact, possibly enhanced by grain boundary diffusion; The macroscopic response to stress is different for cells with identical back-contact, but from different manufacturers. Different factors and/or different reactions to identical factors are possibly at work here; and Ni-P appears to be a promising back-contact material.

  2. Cost analysis methodology: Photovoltaic Manufacturing Technology Project. Annual subcontract report, 11 March 1991--11 November 1991

    Energy Technology Data Exchange (ETDEWEB)

    Whisnant, R.A. [Research Triangle Inst., Research Triangle Park, NC (United States)

    1992-09-01

    This report describes work done under Phase 1 of the Photovoltaic Manufacturing Technology (PVMaT) Project. PVMaT is a five-year project to support the translation of research and development in PV technology into the marketplace. PVMaT, conceived as a DOE/industry partnership, seeks to advanced PV manufacturing technologies, reduce PV module production costs, increase module performance, and expand US commercial production capacities. Under PVMaT, manufacturers will propose specific manufacturing process improvements that may contribute to the goals of the project, which is to lessen the cost, thus hastening entry into the larger scale, grid-connected applications. Phase 1 of the PVMaT project is to identify obstacles and problems associated with manufacturing processes. This report describes the cost analysis methodology required under Phase 1 that will allow subcontractors to be ranked and evaluated during Phase 2.

  3. Amorphous silicon photovoltaic manufacturing technology - Phase 2A. Annual subcontract report, May 1, 1993--April 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Duran, G.; Mackamul, K.; Metcalf, D. [Utility Power Group, Chatsworth, CA (United States)

    1995-01-01

    Utility Power Group (UPG), and its lower-tier subcontractor, Advanced Photovoltaic Systems, Inc. (APS) have conducted efforts in developing their manufacturing lines. UPG has focused on the automation of encapsulation and termination processes developed in Phase I. APS has focused on completion of the encapsulation and module design tasks, while continuing the process and quality control and automation projects. The goal is to produce 55 watt (stabilized) EP50 modules in a new facility. In the APS Trenton EUREKA manufacturing facility, APS has: (1) Developed high throughput lamination procedures; (2) Optimized existing module designs; (3) Developed new module designs for architectural applications; (4) Developed enhanced deposition parameter control; (5) Designed equipment required to manufacture new EUREKA modules developed during Phase II; (6) Improved uniformity of thin-film materials deposition; and (7) Improved the stabilized power output of the APS EP50 EUREKA module to 55 watts. In the APS Fairfield EUREKA manufacturing facility, APS has: (1) Introduced the new products developed under Phase I into the APS Fairfield EUREKA module production line; (2) Increased the extent of automation in the production line; (3) Introduced Statistical Process Control to the module production line; and (4) Transferred-progress made in the APS Trenton facility into the APS Fairfield facility.

  4. Investigation of test methods, material properties, and processes for solar cell encapsulants. Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Willis, P. B.; Baum, B.

    1979-06-01

    The goal of this program is to identify, evaluate, and recommend encapsulant materials and processes for the production of cost-effective, long-life solar cell modules. During the past year, the technical activities emphasized the reformulation of a commercial grade of ethylene/vinyl acetate copolymer for use as a pottant in solar cell module manufacture. After experimenting with a variety of techniques, a vacuum-bag process was developed and found to be an excellent encapsulation method. Adhesive strengths and primers for the bonding of ethylene/vinyl acetate to superstrate and substrate materials was assessed with encouraging results. The weathering effects on ten other polymers exposed to twelve months of weathering in Arizona, Florida, and under EMMAQUA were evaluated by determination of tensile strengths, elongations, optical transmission, etc. As may be expected, the best overall retention of mechanical properties is found for the fluorocarbon polymers, especially FEP. Hard coatings containing ultraviolet absorbers were investigated for the purpose of providing a soil resistant surface and additional weathering stability to the soft EVA pottant. Corrosion studies using a standard salt spray test were used to determine the degree of protection offered to a variety of metals by encapsulation in EVA pottant. A survey of scrim materials was also conducted. These open hole weaves are intended for use as spacers between the cell and substrate to provide a mechanical barrier, improve insulation resistance and prevent migration of the pigmented pottant over the cell surface. A mechanical engineering analysis of composite structural materials for use as substrates was performed. Results are presented in detail. (WHK)

  5. Investigation of test methods, material properties, and processes for solar cell encapsulants. Seventh annual report

    Energy Technology Data Exchange (ETDEWEB)

    Willis, P.B.

    1983-01-01

    The goal of the program is to identify and evaluate encapsulation materials and processes for the protection of silicon solar cells for service in a terrestrial environment. Aging and degradation studies were performed including: thermal aging, sunlamp exposures, aging in controlled environment reactors and outdoor photothermal aging devices, and metal catalyzed degradation. Other tests addressed water absorption, primers and adhesives, soiling experiments, and corrosion protection. (LEW)

  6. [Hydroxyproline: Rich glycoproteins of the plant and cell wall]. Annual technical progress report, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Varner, J.E.

    1993-06-01

    Since xylem tissue includes the main cell types which are lignified, we are interested in gene expression of glycine-rich proteins and proline-rich proteins, and other proteins which are involved in secondary cell wall thickening during xylogenesis. Since the main feature of xylogenesis is the deposition of additional wall components, study of the mechanism of xylogenesis will greatly advance our knowledge of the synthesis and assembly of wall macromolecules. We are using the in vitro xylogenesis system from isolated Zinnia mesophyll cells to isolate genes which are specifically expressed during xylogenesis. We have used subtractive hybridization methods to isolate a number of cDNA clones for differentially regulated genes from the cells after hormonal induction. So far, we have partially characterized 18 different cDNA clones from 239 positive clones. These differentially regulated genes can be divided into three sets according to the characteristics of gene expression in the induction medium and the control medium. The first set is induced in both the induction medium and the control medium without hormones. The second set is induced mainly in the induction medium and in the control medium with the addition of NAA alone. Two of thesegenes are exclusively induced by auxin. The third set of genes is induced mainly in the induction medium. Since these genes are not induced by either auxin or cytokinin alone, they may be directly involved in the process of xylogenesis. Our experiments on the localization of H{sub 2}O{sub 2} production reinforce the earlier ideas of others that H{sub 2}O{sub 2} is involved in normal lignification.

  7. Hematopoietic stem cell transplantation in Europe 2014: more than 40 000 transplants annually.

    Science.gov (United States)

    Passweg, J R; Baldomero, H; Bader, P; Bonini, C; Cesaro, S; Dreger, P; Duarte, R F; Dufour, C; Kuball, J; Farge-Bancel, D; Gennery, A; Kröger, N; Lanza, F; Nagler, A; Sureda, A; Mohty, M

    2016-06-01

    A record number of 40 829 hematopoietic stem cell transplantation (HSCT) in 36 469 patients (15 765 allogeneic (43%), 20 704 autologous (57%)) were reported by 656 centers in 47 countries to the 2014 survey. Trends include: continued growth in transplant activity, more so in Eastern European countries than in the west; a continued increase in the use of haploidentical family donors (by 25%) and slower growth for unrelated donor HSCT. The use of cord blood as a stem cell source has decreased again in 2014. Main indications for HSCT were leukemias: 11 853 (33%; 96% allogeneic); lymphoid neoplasias; 20 802 (57%; 11% allogeneic); solid tumors; 1458 (4%; 3% allogeneic) and non-malignant disorders; 2203 (6%; 88% allogeneic). Changes in transplant activity include more allogeneic HSCT for AML in CR1, myeloproliferative neoplasm (MPN) and aplastic anemia and decreasing use in CLL; and more autologous HSCT for plasma cell disorders and in particular for amyloidosis. In addition, data on numbers of teams doing alternative donor transplants, allogeneic after autologous HSCT, autologous cord blood transplants are presented.

  8. Molten carbonate fuel cell product development test. Annual report, October 1992--September 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-01

    Advanced fuel cell active components have been developed and scaled up from laboratory scale to commercial scale. Full width components of both the stabilized nickel cathodes and the low chrome anodes have been successfully cast on M-C Power`s production tape caster. An improved design for a fuel cell separator plate has been developed. The improved design meets the goals of lower cost and manufacturing simplicity, and addresses performance issues of the current commercial area plate. The engineering that the Bechtel Corporation has completed for the MCFC power plant includes a site design, a preliminary site layout, a Process Flow Diagram, and specification for the procurement of some of the major equipment items. Raw materials for anode and cathode components were ordered and received during the first half of 1993. Tape casting of anodes was started in late summer and continued through August. In addition to the technical progress mentioned above, an environment assessment was prepared in compliance with the National Environmental Policy Act of 1969 (NEPA). As a result, the PDT has received a categorical exclusion from the Air Pollution Control District permit requirements. The PDT is configured to demonstrate the viability of natural gas-fueled MCFC for the production of electricity and thermal energy in an environmentally benign manner for use in commercial and industrial applications.

  9. Specific PVMaT R&D in CdTe Product Manufacturing: Final Subcontract Report, March 2003

    Energy Technology Data Exchange (ETDEWEB)

    Bohland, J.; McMaster, A.; Henson, S.; Hanak, J.

    2004-01-01

    Results of a 3+ year subcontract are presented. The research was conducted under Phase 5A2 of the subcontract. The three areas of effort in the subcontract were (1) manufacturing line improvements, (2) product readiness, and (3) environmental, safety, and health programs. The subcontract consisted of three phases, approximately 1 year each. Phase I included the development, design, and implementation of a high-throughput, low-cost lamination process. This goal was achieved using the support of key experts such as Automation and Robotics Research Institute (ARRI) to identify appropriate lamination equipment vendors, and material handling. Product designs were reviewed by Arizona State University Photovoltaic Testing Laboratory and Underwriters Laboratories. Modifications to the module designs were implemented to meet future testing requirements. A complete review of the Environmental, Health, and Safety programs was conducted, along with training by the Environmental Protection Agency (EP A) and Occupational Safety and Health Administration (OSHA). Work conducted during Phase II included the implementation of an improved potting procedure for the wiring junction. The design of the equipment focused on high-throughput, low-cost operations. During Phase III , First Solar made significant progress in three areas: Manufacturing Readiness; Product Performance; and Environmental, Health, and Safety (EH&S). First Solar's accomplishments in laser scribing significantly exceeded the stated goals. Innovations implemented during Phase III were made possible by adopting a new type of high-frequency, low-pulse-width laser, galvanometer-driven laser-beam system, and numerous advanced, automated, equipment features. Because of the greater than one order of magnitude increase in the throughput and laser life, a factor of two decrease in equipment cost, and complete automation, a major impact on lowering the cost of the PV product is anticipated.

  10. 48 CFR 12.504 - Applicability of certain laws to subcontracts for the acquisition of commercial items.

    Science.gov (United States)

    2010-10-01

    ... (except for the types of subcontracts listed at 47.504(d)). (2) 15 U.S.C. 644(d), Requirements relative to... American Vessels of Government Personnel and Certain Cargo (see Subpart 47.5) (except for the types of... U.S.C. 254(d) and 10 U.S.C. 2306a, Truth in Negotiations Act (see subpart 15.4). (3) 41 U.S.C....

  11. Investigation of test methods, material properties, and processes for solar-cell encapsulants. Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Willis, P. B.; Baum, B.

    1982-07-01

    Potentially useful low cost encapsulation materials are evaluated. The goal of the program is to identify, evaluate, test, and recommend encapsulant materials and processes for the production of cost-effective, long life solar cell modules. Technical investigations have concerned the development of advanced cure chemistries for lamination type pottants, the continued evaluation of soil resistant surface treatments, and the results of an accelerated aging test program for the comparison of material stabilities. Experiments are underway to assess the durability and cost effectiveness of coatings for protection of steel. Investigations are continuing with commercial maintenance coatings based on fluorocarbon and silicone-alkyd chemistries. Experiments were conducted to determine the effectiveness of occlusive coatings for wood products such as hard-board. An experimental program continued to determine the usefulness of soil resistant coatings. Primers were evaluated for effectiveness in bonding candidate pottants to outer covers, glass and substate materials. A program of accelerated aging and life predictive strategies is being conducted and data are reported for sunlamp exposure and thermal aging. Supporting activities are also discussed briefly. (LEW)

  12. Investigation of test methods, material properties, and processes for solar cell encapsulants. Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Willis, P. B.; Baum, B.; White, R. A.

    1978-06-01

    Springborn Laboratories is engaged in a study of evaluating potentially useful encapsulating materials for the encapsulation task of the Low-Cost Solar Array project (LSA) funded by the Department of Energy. The goal of this program is to identify, evaluate, and recommend encapsulant materials (other than glass) and processes for the production of cost-effective, long-life photovoltaic solar modules. The results of an investigation of solar module encapsulation systems applicable to the Low-Cost Solar Array project 1986 cost and performance goals are presented. The 1986 cost goal for a 20 year life solar cell module is $0.50 per watt or $5 per square foot (in 1975 dollars). Out of this cost goal, $0.25 per square foot is currently allocated for the encapsulation in terms of raw materials, exclusive of labor. Assuming the flat-plate collector to be the most efficient module design, six basic construction elements were identified and their specific uses in module construction defined. In order to generate a comparative analysis, a uniform costing basis was established for each element. Extensive surveys into commercially available materials were then conducted in order to identify either general classes or specific products suitable for use for each construction element. The survey results were also useful in revealing price ranges for classes of materials and estimating the cost allocation for each element within the encapsulation cost goal.

  13. The Organized Foundation of Administrative Subcontract%行政包干的组织基础

    Institute of Scientific and Technical Information of China (English)

    张静

    2014-01-01

    As a response to the issue of the origin of “administrative subcontract”in China ,different from the“cost measuring” explanation , this paper suggests that the roots of the subcontracting system could be found in the body of the administrative organization ,its own characteristics and historical ties . Due to its multi‐roles , its multi‐centered organizational form , and its dependence on organizational implement tool ,the government system has gradually developed a flexible and adaptable way which is capable of employing the above‐mentioned organizational environment to perform tasks .This has made it different from a single bureaucratic system . Taking advantage of the self‐evident control power ,“administrative subcontract system” manages to gather organizations with different goals and interests by means of acquiescence , exchange and invisible authorization ,which ends up forming a mixed system of governance we can see today . Therefore , the structure of government administrative system , its internal organizational relationships and its multi‐roles , is the cornerstone based on which the sub‐contracting system comes into being .%回应“行政包干”的缘起问题,针对“成本衡量”说,本文建议从行政机体本身的特性和历史关系,说明发包制的存在。由于政府的多元角色、多中心控制权的组织关系以及对执行工具的依赖,政府系统逐渐发展出具有灵活适应性的、不同于单一科层体系的、能够利用上述组织环境的方法,来推进任务的执行。“行政包干制”顺势于不言自明的控制权范围,通过默许、交换和隐形授权,将目标和利益不同的组织容纳于一体,形成了今天治理体系中混合共生的形态。因此,政府行政体系的组成结构、其内部真实的组织关系和多元角色是发包制产生的基石。

  14. NREL photovoltaic subcontract reports: Abstracts and document control information, 1 August 1992--31 July 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    This report contains document control information and abstracts for the National Renewable Energy Laboratory (NREL) subcontracted photovoltaic (PV) program publications. It also lists source information on additional publications that describe US Department of Energy (DOE) PV research activities. It is not totally exhaustive, so it lists NREL contacts for requesting further information on the DOE and NREL PV programs. This report covers the period from August 1, 1992, through July 31, 1993. This report is published periodically, with the previous one covering the period from August 1, 1991, through July 31, 1992. The purpose of continuing this type of publication is to help keep people abreast of specific PV interests, while maintaining a balance on the costs to the PV program. The information in this report is organized under PV technology areas: Amorphous Silicon Research; Polycrystalline Thin Films (including copper indium diselenide, cadmium telluride, and thin-film silicon); Crystalline Materials and Advanced Concepts (including silicon, gallium arsenide, and other group III-V materials); PV Manufacturing Technology Development (which may include manufacturing information for various types of PV materials).

  15. Processing of CuInSe{sub 2}-based solar cells: Characterization of deposition processes in terms of chemical reaction analyses. Phase 2 Annual Report, 6 May 1996--5 May 1997

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, T.

    1999-10-20

    This report describes research performed by the University of Florida during Phase 2 of this subcontract. First, to study CIGS, researchers adapted a contactless, nondestructive technique previously developed for measuring photogenerated excess carrier lifetimes in SOI wafers. This dual-beam optical modulation (DBOM) technique was used to investigate the differences between three alternative methods of depositing CdS (conventional chemical-bath deposition [CBD], metal-organic chemical vapor deposition [MOCVD], and sputtering). Second, a critical assessment of the Cu-In-Se thermochemical and phase diagram data using standard CALPHAD procedures is being performed. The outcome of this research will produce useful information on equilibrium vapor compositions (required annealing ambients, Sex fluxes from effusion cells), phase diagrams (conditions for melt-assisted growth), chemical potentials (driving forces for diffusion and chemical reactions), and consistent solution models (extents of solid solutions and extending phase diagrams). Third, an integrated facility to fabricate CIS PV devices was established that includes migration-enhanced epitaxy (MEE) for deposition of CIS, a rapid thermal processing furnace for absorber film formation, sputtering of ZnO, CBD or MOCVD of CdS, metallization, and pattern definition.

  16. U.S. Department of Energy Hydrogen and Fuel Cells Program 2014 Annual Merit Review and Peer Evaluation Report: June 16-20, 2014, Washington, D.C.

    Energy Technology Data Exchange (ETDEWEB)

    2014-10-01

    The fiscal year (FY) 2014 U.S. Department of Energy (DOE) Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting (AMR), in conjunction with DOE's Vehicle Technologies Office AMR, was held from June 16-20, 2014, at the Washington Marriott Wardman Park in Washington, D.C. This report is a summary of comments by AMR peer reviewers about the hydrogen and fuel cell projects funded by DOE's Office of Energy Efficiency and Renewable Energy (EERE).

  17. Development of Modular Subcontract Documents for Construction Projects%工程项目分包合同招标文件的模块化开发

    Institute of Scientific and Technical Information of China (English)

    陈勇强; 张水波

    2001-01-01

    论述在工程项目管理中分包合同与主合同之间的关系,提出用模块化的思想进行分包合同招标文件开发与管理的新思路,分析分包合同招标文件模块化开发的优点,最后指出工程分包合同招标文件编制应注意的问题。%This paper first discusses the relationship between subcontract and main contract, proposes the innovative method for developing subcontracting documents by modularization and analyzes the advantage of this method. Finally, some points that should be noted in preparation of subcontract documents are put forward.

  18. Fabrication of stable, large-area thin-film CdTe photovoltaic modules. Final subcontract report, May 10, 1991--February 28, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, T.X. [Solar Cells, Inc., Toledo, OH (United States)

    1995-06-01

    During the period of this subcontract, May 1991 through February 1995, Solar Cells, Inc. has developed and demonstrated a low-cost process to fabricate stable large-area cadmium telluride based thin-film photovoltaic modules. This report summarizes the final phase of the project which is concentrated on process optimization and product life tests. One of the major post-deposition process steps, the CdCl{sub 2} heat treatment, has been experimentally replaced with alternative treatments with vapor chloride or chlorine gas. Material and device qualities associated with alternative treatments are comparable or superior to those with the conventional treatment. Extensive experiments have been conducted to optimize the back-electrode structure in order to ensure long term device stability. Numerous small-area cells and minimodules have been subjected to a variety of stress tests, including but not limited to continuous light soak under open or short circuit or with resistive load, for over 10,000 hours. Satisfactory stability has been demonstrated on 48 cm{sup 2} and 64 cm{sup 2} minimodules under accelerated tests and on 7200 cm{sup 2} large modules under normal operating conditions. The conversion efficiency has also been significantly improved during this period. The total area efficiency of 7200 cm{sup 2} module has reached 8.4%, corresponding to a 60.3W normalized output; the efficiency of 64 cm{sup 2} minimodules and 1.1 cm{sup 2} cells has reached 10.5% (aperture area) and 12.4% (total area), respectively.

  19. 48 CFR 252.209-7004 - Subcontracting with firms that are owned or controlled by the government of a terrorist country.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Subcontracting with firms that are owned or controlled by the government of a terrorist country. 252.209-7004 Section 252.209-7004 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CLAUSES AND FORMS SOLICITATION...

  20. NREL Photovoltaic Program FY 1995 annual report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    This report summarizes the in-house and subcontracted R&D activities from Oct. 1994 through Sept. 1995; their objectives are to conduct basic, applied, and engineering research, manage subcontracted R&D projects, perform research complementary to subcontracted work, develop and maintain state-of-the-art measurement and device capabilities, develop PV manufacturing technology and modules, transfer results to industry, and evolve viable partnerships for PV systems and market development. The research activities are grouped into 5 sections: crystalline Si and advanced devices, thin-film PV, PV manufacturing, PV module and system performance and engineering, and PV applications and market development.

  1. SERI photovoltaic subcontract reports: 1989 abstracts and document control information, March 1, 1987 to February 29, 1988

    Science.gov (United States)

    Guha, S.

    1990-04-01

    Document control information and abstracts for SERI Photovoltaic (PV) Program Branch publications resulting from SERI's subcontracted PV research is presented. The information is presented for reports published and distributed during fiscal year (FY) 1989. In the past, copies of the subcontractor reports were distributed to a broad spectrum of researchers in the field of photovoltaics at a considerable cost to the program. In an attempt to reduce costs and ensure that all researchers receive those current publications that are of specific interest to them, these publications are outlined and organized by technology, on a regular basis. Subsequent reports are expected to be distributed quarterly. A list of additional publications and sources is included herein to provide the photovoltaic community with other sources of information.

  2. An Industrial-Based Consortium to Develop Premium Carbon Products from Coal, Annual Progress Report, October 1, 2005 through September 30, 2006

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Bruce G

    2006-09-29

    Since 1998, The Pennsylvania State University has been successfully managing the Consortium for Premium Carbon Products from Coal (CPCPC), which is a vehicle for industry-driven research on the promotion, development, and transfer of innovative technology on premium carbon produces from coal to the U.S. industry. The CPCPC is an initiative being led by Penn State, its co-charter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provides the base funding for the program, with Penn State responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity has continued under the present cooperative agreement, No. DE-FC26-03NT41874, which started October 1, 2003. The objective of the second agreement is to continue the successful operation of the CPCPC. The CPCPC has enjoyed tremendous success with its organizational structure, that includes Penn State and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC is its industry-led council that selects proposals submitted by CPCPC members to ensure CPCPC target areas have strong industrial support. Base funding for the selected projects is provided by NETL with matching funds from industry. At the annual funding meeting held in October 2003, ten projects were selected for funding. Subcontracts were let from Penn State to the subcontractors on March 1, 2004. Nine of the ten 2004 projects were completed during the previous annual reporting period and their final reports were submitted with the previous annual report (i.e., 10/01/04-09/30/05). The final report for the remaining project, which was submitted during this reporting

  3. Cellular heredity in haploid cultures of somatic cells. Annual progress report, March 1, 1975--March 31, 1976. [UV radiation

    Energy Technology Data Exchange (ETDEWEB)

    Freed, J.J.

    1976-01-01

    In experiments with haploid and diploid derivatives from the haploid frog embryo cell line ICR 2A, we have investigated aspects of cell survival, DNA repair and mutant induction after exposure to 254 nm radiation. Survival curves for haploid and diploid cells in random growth or blocked in the Gl phase of the cell cycle were determined; the survival data do not differ sufficiently to permit the use of such comparisons as an index of recessive lethal induction. Studies of the induction of thymine dimers in DNA indicated that the incidence of dimers in DNA from haploid and diploid cells is similar after exposure of the cells to equal doses of ultraviolet. The cells are capable of photoreversing dimers but appear to be deficient in excision repair. In an attempt to examine the effect of the permitted mode of DNA repair on the yield of mutations, we compared the incidence of ouabain-resistant variants among survivors of ultraviolet exposure and of ultraviolet exposure followed by photoreversal. Although the yield of resistant colonies was small, the data suggest that photoreversal lowers the yield of resistant colonies and thus that the induction of this phenotype is related to dimer persistence in DNA. We have also observed by fluorescence microscopy that an acridine mustard mutagen, ICR 191, is preferentially accumulated in cytoplasmic granules having the intracellular distribution pattern of lysosomes. This form of incorporation may be significant in the apparently non-genetic early toxicity of this compound observed in experiments with cultured cells.

  4. Wide band gap solar cells with high stabilized performance. Annual technical report, 15 July 1995--15 July 1996

    Energy Technology Data Exchange (ETDEWEB)

    Wronski, C R; Collins, R W; Fujiwara, H [Pennsylvania State Univ., University Park, PA (United States); and others

    1997-01-01

    This report describes work on an improved understanding of stability in materials and silicon solar cells. Topics include novel intrinsic materials optimization; solar cells optimized for p- and i-layer performance; novel p-type materials; interfaces; and device modeling.

  5. Process Development for High Voc CdTe Solar Cells: Phase I, Annual Technical Report, October 2005 - September 2006

    Energy Technology Data Exchange (ETDEWEB)

    Ferekides, C. S.; Morel, D. L.

    2007-04-01

    The focus of this project is the open-circuit voltage of the CdTe thin-film solar cell. CdTe continues to be one of the leading materials for large-scale cost-effective production of photovoltaics, but the efficiency of the CdTe solar cell has been stagnant for the last few years. At the manufacturing front, the CdTe technology is fast paced and moving forward with U.S.-based First Solar LLC leading the world in CdTe module production. To support the industry efforts and continue the advancement of this technology, it will be necessary to continue improvements in solar cell efficiency. A closer look at the state-of-the-art performance levels puts the three solar cell efficiency parameters of short-circuit current density (JSC), open-circuit voltage (VOC), and fill factor (FF) in the 24-26 mA/cm2, 844?850 mV, and 74%-76% ranges respectively. During the late 1090s, efforts to improve cell efficiency were primarily concerned with increasing JSC, simply by using thinner CdS window layers to enhance the blue response (<510 nm) of the CdTe cell. These efforts led to underscoring the important role 'buffers' (or high-resistivity transparent films) play in CdTe cells. The use of transparent bi-layers (low-p/high-p) as the front contact is becoming a 'standard' feature of the CdTe cell.

  6. Advanced therapy medicinal products : How to bring cell-based medicinal products successfully to the market - Report from the CAT-DGTI-GSCN Workshop at the DGTI Annual Meeting 2014

    NARCIS (Netherlands)

    Celis, Patrick; Ferry, Nicolas; Hystad, Marit; Schüßler-Lenz, Martina; Doevendans, Pieter A.; Flory, Egbert; Beuneu, Claire; Reischl, Ilona; Salmikangas, Paula

    2015-01-01

    On September 11, 2014, a workshop entitled 'Advanced Therapy Medicinal Products: How to Bring Cell-Based Medicinal Product Successfully to the Market' was held at the 47th annual meeting of the German Society for Transfusion Medicine and Immunohematology (DGTI), co-organised by the European Medicine

  7. Optimization of transparent and reflecting electrodes for amorphous silicon solar cells. Annual technical report, April 1, 1995--March 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, R.G.; Sato, H.; Liang, H.; Liu, X.; Thornton, J. [Harvard Univ., Cambridge, MA (United States)

    1996-08-01

    The general objective is to develop methods to deposit materials which can be used to make more efficient solar cells. The work is organized into three general tasks: Task 1. Develop improved methods for depositing and using transparent conductors of fluorine-doped zinc oxide in amorphous silicon solar cells Task 2. Deposit and evaluate titanium oxide as a reflection-enhancing diffusion barrier between amorphous silicon and an aluminum or silver back-reflector. Task 3. Deposit and evaluate electrically conductive titanium oxide as a transparent conducting layer on which more efficient and more stable superstrate cells can be deposited. About one-third of the current project resources are allocated to each of these three objectives.

  8. Polycrystalline thin film cadmium telluride solar cells fabricated by electrodeposition. Annual technical report, 20 March 1995--19 March 1996

    Energy Technology Data Exchange (ETDEWEB)

    Trefny, J U; Mao, D [Colorado School of Mines, Golden, CO (United States)

    1997-04-01

    The objective of this project is to develop improved processes for fabricating CdTe/CdS polycrystalline thin-film solar cells. Researchers used electrodeposition to form CdTe; electrodeposition is a non-vacuum, low-cost technique that is attractive for economic, large-scale production. During the past year, research and development efforts focused on several steps that are most critical to the fabricating high-efficiency CdTe solar cells. These include the optimization of the CdTe electrodeposition process, the effect of pretreatment of CdS substrates, the post-deposition annealing of CdTe, and back-contact formation using Cu-doped ZnTe. Systematic investigations of these processing steps have led to a better understanding and improved performance of the CdTe-based cells. Researchers studied the structural properties of chemical-bath-deposited CdS thin films and their growth mechanisms by investigating CdS samples prepared at different deposition times; investigated the effect of CdCl{sub 2} treatment of CdS films on the photovoltaic performance of CdTe solar cells; studied Cu-doped ZnTe as a promising material for forming stable, low-resistance contacts to the p-type CdTe; and investigated the effect of CdTe and CdS thickness on the photovoltaic performance of the resulting cells. As a result of their systematic investigation and optimization of the processing conditions, researchers improved the efficiency of CdTe/CdS cells using ZnTe back-contact and electrodeposited CdTe. The best CdTe/CdS cell exhibited a V{sub oc} of 0.778 V, a J{sub sc} of 22.4 mA/cm{sup 2}, a FF of 74%, and an efficiency of 12.9% (verified at NREL). In terms of individual parameters, researchers obtained a V{sub oc} over 0.8 V and a FF of 76% on other cells.

  9. 再论行政发包制:对评论人的回应%Rethinking Administrative Subcontract:Reply

    Institute of Scientific and Technical Information of China (English)

    周黎安

    2014-01-01

    This piece serves as a response to the comments on my paper“Administrative Subcontract” made by Zhou Xueguang ,Zhang Jing ,Cao Zhenghan ,and Feng Shizheng .My reply focuses both on their critical comments and suggestions . Our differences center on such issues as the definition , content ,and causes of administrative subcontract system ,the definition and implications of ruling risks ,and authority allocation between the principal and the agent .In the reply I try to clarify the confusions and explain the reasons why we differ in these matters and indicate my stance . Following the commentators’ critical comments and suggestions ,I also discuss the possibilities and directions for further improvement of the administrative subcontract theory . In the conclusion ,I propose three criteria for a good theory and highlight the importance of interdisciplinary academic exchange and interaction in developing a good theory .%本文对周雪光、张静、曹正汉和冯仕政四位教授的评论文章进行了回应。笔者的回应侧重在各位评论人提出的带有批判性质的意见和建议上。笔者和评论人的分歧主要集中在行政发包制的界定、内涵和形成原因、统治风险的内涵和影响、发包人和承包人的权力配置等问题上,对于这些问题,笔者试图做进一步的澄清和解释。鉴于评论人的批评建议,本文也讨论了行政发包制未来可以进一步扩展和完善的领域。最后,笔者提出了一个好的理论的三个标准,并讨论了跨学科交流对于发展好理论的重要意义。

  10. Contaminant resistant molten carbonate fuel cell: Annual report, June 1986--June 1987. [Ni hydrogen-permeablel barriers

    Energy Technology Data Exchange (ETDEWEB)

    Remick, R.J.; Jewulski, J.R.; Lu, S.H.

    1987-06-01

    This report summarizes the results of a year-long program evaluating the application of solid nickel foils as hydrogen-permeable barriers to contaminants (H/sub 2/S, HCl, NH/sub 3/) in molten carbonate fuel cells. A parametric study was conducted using 2.5 to 7.5 ..mu..m thick nickel foils in both laboratory-scale and bench-scale fuel cell tests. Two design configurations were evaluated, one in which the foil was placed adjacent to the electrolyte matrix and one in which the foil was placed between two porous metal plaques. In both cases the foil served as a barrier for contaminants. Post-test analysis of electrolyte matrices indicated that both configurations retarded or prevented contaminants from reaching the electrolyte. However, problems were encountered with the first configuration in that gaseous products built up on the electrolyte side of the anode, substantially increasing cell polarization. The second configuration performed significantly better than the first, delivering a performance nearly equal to that of a standard porous metal anode structure. However, the flux of hydrogen crossing the foil in this configuration proved to be sensitive to sulfur contaminants in the fuel. As a consequence, a reduction in current density at constant cell voltage was observed when H/sub 2/S was present in the fuel, despite the fact that no H/sub 2/S reached the three-phase region where electrode, fuel, and electrolyte meet. This behavior, however, may be overcome by using a foil other than pure nickel. 36 refs., 30 figs., 22 tabs.

  11. High-efficiency thin-film cadmium telluride photovoltaic cells. Annual technical report, January 20, 1996--January 19, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Compaan, A D; Bohn, R G; Contreras-Puente, G [Univ. of Toledo, OH (United States)

    1997-08-01

    The University of Toledo photovoltaics group has been instrumental in developing rf sputtering for CDs/CdTe thin-film solar cells. During the third phase of the present contract our work focussed on efforts to determine factors which limit the efficiency in our {open_quotes}all-sputtered{close_quotes} thin-film CdTe solar cells on soda-lime glass. We find that our all-sputtered cells, which are deposited at substantially lower temperature than those by sublimation or vapor deposition, require less aggressive CdCl{sub 2} treatments than do other deposition techniques and this is presumably related to CDs/CdTe interdiffusion. The CDs/CdTe interdiffusion process has been studied by several methods, including photoluminescence and capacitance-voltage measurements. Furthermore, we have deposited special thin bilayer films on quartz and borosilicate glass. Interdiffusion in these thin bilayers have been probed by Rutherford backscattering, with collaborators at Case Western Reserve University, and grazing incidence x-ray scattering (GIXS), with collaborators at the University at Buffalo and Brookhaven National Lab. Also, in order better to understand the properties of the ternary alloy material, we used laser physical vapor deposition to prepare a series of CdS{sub x}Te{sub 1-x} films on borosilicate glass. The composition of the alloy films was determined by wavelength dispersive x-ray spectroscopy at NREL. These films are currently being investigated by us and other groups at NREL and IEC.

  12. Cellular morphometry and cycling cell populations of human and dog bronchi. Annual progress report, April 1, 1994--March 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Robbins, E.S.

    1994-12-01

    Quantitative data of the human bronchial epithelial cells at possible risk for malignant transformation in lung cancer is crucial for accurate radon dosimetry and risk analysis. The nuclei of these cells may be targets for damage by {alpha} particles. Then it is important to determine the locations and other parameters of these nuclei in different airway generations, among smokers, non-smokers and ex-smokers, between men and women and in people of different ages. This proposal includes extended morphometric studies on electron micrographs of human bronchial epithelium of defined airway generations. The second part of this proposal describes the continuation of studies to quantitate the cycling tracheo-bronchial epithelial population(s) using proliferation markers and immunocytochemistry on paraffin sections. The proliferative potential of the airway mucosa of smokers, non-smokers, and ex-smokers, men and women, as well as individuals of different ages are being compared. Normal human bronchial linings are also being compared with normal adult dog bronchi and metaplastic and repairing human airways. Since cycling cells can be more sensitive to damage from carcinogens and radioactivity, the quantitative data from this project will allow the development of more accurate radon risk analysis.

  13. Chemical Profiles of Microalgae with Emphasis on Lipids: A Subcontract Report

    Energy Technology Data Exchange (ETDEWEB)

    Tornabene, T. G.; Hubbard, J. S.

    1984-09-01

    Well balanced cultivated cells that are healthy and unstressed produce the optimum cellular yield. All stress studies for lipids production should be conducted with the established cell mass and not be administered during active cultivation. Cells cultivated continually in suboptimum conditions produce lower cellular yields and continuous cultivation in suboptimum media and environmental conditions produce lower than normal lipid levels. Lipid triggers are preceded by a burst of carbohydrate synthesis and storage.

  14. Development of solid oxide fuel cell (SOFC). Fourth semi-annual progress report: February 1992 - July 1992

    Energy Technology Data Exchange (ETDEWEB)

    Huijsmans, J.P.P.; Van Heuveln, F.H.; Van Berkel, F.P.F.

    1992-11-01

    The Netherlands Energy Research Foundation (ECN), Petten, Netherlands, is carrying out the title programme in cooperation with Siemens in Germany, Imperial College and GEC Alshom in the United Kingdom. ECN will develop and investigate alternative materials manufacturing procedures and test alternative cell concepts. Activities of ECN include electrode powder fabrication, development of ceramic components, development of metal separator plate, physico-chemical characterization, chemical interface problems between ceramic components, materials testing, and proof-of-principle of 3 Watt (50x50 mm{sup 2}) and 10 Watt (100x100 mm{sup 2}) level SOFC`s. 7 figs., 4 tabs., 3 refs.

  15. Technology Support for High-Throughput Processing of Thin-Film CdTe PV Modules Annual Technical Report, Phase II

    Energy Technology Data Exchange (ETDEWEB)

    Rose, D.H.; Powell, R.C.; Karpov, V.; Grecu, D.; Jayamaha, U.; Dorer, G.L. (First Solar, L.L.C.)

    2001-02-05

    Results and conclusions from Phase II of a three-year subcontract are presented. The subcontract, entitled Technology Support for High-Throughput Processing of Thin-Film CdTe PV Modules, is First Solar's portion of the Thin-Film Photovoltaic Partnership Program. The research effort of this subcontract is divided into four areas of effort: (1) process and equipment development, (2) efficiency improvement, (3) characterization and analysis, and (4) environmental, health, and safety. As part of the process and equipment development effort, a new semiconductor deposition system with a throughput of 3 m2/min was completed, and a production line in a new 75,000 ft2 facility was started and is near completion. As part of the efficiency-improvement task, research was done on cells and modules with thin CdS and buffer layers as way to increase photocurrent with no loss in the other photovoltaic characteristics. A number of activities were part of the characterization and analysis task, including developing a new admittance spectroscopy system, with a range of 0.001 Hz to 100 kHz, to characterize cells. As part of the environmental, health, and safety task, the methanol-based CdCl2 process was replaced with aqueous-CdCl2. This change enabled the retention of a De Minimus level of emissions for the manufacturing plant, so no permitting is required.

  16. Development of Solid Oxide Fuel Cell (SOFC). Third semi-annual progress report August 1991-January 1992

    Energy Technology Data Exchange (ETDEWEB)

    Huijsmans, J.P.P.; Van Heuveln, F.H.; Van Berkel, F.P.F.

    1992-06-01

    The Netherlands Energy Research Foundation (ECN) is carrying out the title cooperative research programme, sponsored by the Committee of the European Communities (CEC) JOULE programme. Partners in the programme are Siemens AG (Germany), ECN, Imperial College (UK), and GEC Alsthom (UK). ECN will develop and investigate materials manufacturing procedures and will test alternative cell concepts. Activities of ECN include electrode powder fabrication, development of ceramic components, development of metal separator plate, physico-chemical characterization, chemical interface problems between ceramic components, materials testing, and proof-of principle of 3 Watt (50x50 mm{sup 2}) and 10 Watt (100x100 mm{sup 2}) level SOFC`s. 4 figs., 11 refs.

  17. In-situ characterization of growth and interfaces in a-Si:H devices. Annual subcontract report, 1 May 1991--30 April 1992

    Energy Technology Data Exchange (ETDEWEB)

    Collins, R.W.; Wronski, C.R.; An, I.; Li, Y. [Pennsylvania State Univ., University Park, PA (United States)

    1992-12-01

    This report describes the in-situ characterization of growth and interfaces in amorphous silicon (a-Si:H) devices. The growth of a-Si:H by plasma-enhanced chemical vapor deposition (PECVD) is complex and involves many gas-phase and solid-surface chemical and physical processes, which are influenced by charged particle bombardment, ultraviolet light exposure, etc. The research consisted of two broad components. The first involved preparing a-Si:H by ``optimum`` PECVD and exposing the film to atomic hydrogen in-situ at the growth temperature. The processes of H-diffusion and incorporation in the exposed film were studied by spectroscopic ellipsometry, giving a picture of the processes by which the chemical potential in the film equilibrates with that in the gas phase. The properties of thin films were then prepared by alternating ``optimum`` PECVD growth and hydrogen exposure. Film properties were then studied again. The second component of the research is discussed only briefly in this report, as it is an outgrowth of previous work on single-wavelength ellipsometry. With the new spectroscopic capability developed at Penn State, it is now possible to quantify the nucleation and growth process of a-Si:H films.

  18. Novel thin-film CuInSe{sub 2} fabrication. Annual subcontract report, 1 March 1990--30 April 1991

    Energy Technology Data Exchange (ETDEWEB)

    Mooney, G.D.; Hermann, A.M. [Colorado Univ., Boulder, CO (United States)

    1992-03-01

    This report describes research in Rapid Thermal Processing (RTP), a process that allows the formation of CuInSe{sub 2} without the use of H{sub 2}Se. RTP is a well-established method of rapidly achieving temperatures necessary to melt and recrystallize materials such as Si and and silicides. RTP processes can rapidly and uniformly heat large surface areas to hundreds of degrees Celsius. RTP is the most promising method of rapid recrystallization studied to date, being readily scalable from the research to the production level. The approach to the experiment was divided into two sections: (1) fabricating the precursor film and (2) processing the precursor film. The objective of the first phase of the work was to fabricate the thin films by RTP, then fully characterize them, to demonstrate the viability of the process as a method by which to make device-quality CuInSe{sub 2}. The second phase was to demonstrate that material made by this method could be used to make an active photovoltaic device. 24 refs.

  19. Polycrystalline thin film materials and devices. Final subcontract report, 16 January 1990--15 January 1993

    Energy Technology Data Exchange (ETDEWEB)

    Birkmire, R.W.; Phillips, J.E.; Shafarman, W.N.; Hegedus, S.S.; McCandless, B.E.; Yokimcus, T.A. [Delaware Univ., Newark, DE (United States). Inst. of Energy Conversion

    1993-08-01

    This report describes results and conclusions of the final phase (III) of a three-year research program on polycrystalline thin-film heterojunction solar cells. The research consisted of the investigation of the relationships between processing, materials properties, and device performance. This relationship was quantified by device modeling and analysis. The analysis of thin-film polycrystalline heterojunction solar cells explains how minority-carrier recombination at the metallurgical interface and at grain boundaries can be greatly reduced by the proper doping of the window and absorber layers. Additional analysis and measurements show that the present solar cells are limited by the magnitude of the diode current, which appears to be caused by recombination in the space charge region. Developing an efficient commercial-scale process for fabricating large-area polycrystalline, thin-film solar cells from a research process requires a detailed understanding of the individual steps in making the solar cell, and their relationship to device performance and reliability. The complexities involved in characterizing a process are demonstrated with results from our research program on CuInSe{sub 2}, and CdTe processes.

  20. Yields, photosynthetic efficiencies, and proximate chemical composition of dense cultures of marine microalgae. A subcontract report

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, W.H.; Seibert, D.L.R.; Alden, M.; Eldridge, P.; Neori, A.

    1983-07-01

    The yields, photosynthetic efficiencies, and proximate composition of several microalgae were compared in dense cultures grown at light intensities up to 70% sunlight. Yields ranged from 3.4 to 21.7 g dry weight/m/sup 2/ day. The highest yield was obtained with Phaeodactylum; the lowest in Botryococcus cultures. The same species had the highest and lowest efficiencies of utilization of photosynthetically active radiation. In nitrogen-sufficient cells of all but one species, most of the dry weight consisted of protein. Lipid content of all species was 20 to 29%, and carbohydrate content 11 to 23%. Lipid content increased somewhat in N-deficient Phaeodactylum and Isochrysis cells, but decreased in deficient Monallanthus cells. Because the overall dry weight yield was reduced by deficiency, lipid yields did not increase. However, since the carbohydrate content increased to about 65% in N-deficient Dunaliella and Tetraselmis cells, the carbohydrate yield increased. In Phaeodactylum the optimum light intensity was about 40% of full sunlight. Most experimets with this alga included a CUSO/sub 4/ filter to decrease infrared irradiance. When this filter was removed, the yield increased because more red light in the photosynthetically active spectral range was included. These results should prove useful to workers attempting to maximize yields and efficiencies, but additional studies are needed. 69 references, 27 figures, 18 tables.

  1. ISCR FY2005 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Keyes, D E; McGraw, J R

    2006-02-02

    Large-scale scientific computation and all of the disciplines that support and help validate it have been placed at the focus of Lawrence Livermore National Laboratory (LLNL) by the Advanced Simulation and Computing (ASC) program of the National Nuclear Security Administration (NNSA) and the Scientific Discovery through Advanced Computing (SciDAC) initiative of the Office of Science of the Department of Energy (DOE). The maturation of simulation as a fundamental tool of scientific and engineering research is underscored in the President's Information Technology Advisory Committee (PITAC) June 2005 finding that ''computational science has become critical to scientific leadership, economic competitiveness, and national security''. LLNL operates several of the world's most powerful computers--including today's single most powerful--and has undertaken some of the largest and most compute-intensive simulations ever performed, most notably the molecular dynamics simulation that sustained more than 100 Teraflop/s and won the 2005 Gordon Bell Prize. Ultrascale simulation has been identified as one of the highest priorities in DOE's facilities planning for the next two decades. However, computers at architectural extremes are notoriously difficult to use in an efficient manner. Furthermore, each successful terascale simulation only points out the need for much better ways of interacting with the resulting avalanche of data. Advances in scientific computing research have, therefore, never been more vital to the core missions of LLNL than at present. Computational science is evolving so rapidly along every one of its research fronts that to remain on the leading edge, LLNL must engage researchers at many academic centers of excellence. In FY 2005, the Institute for Scientific Computing Research (ISCR) served as one of LLNL's main bridges to the academic community with a program of collaborative subcontracts, visiting faculty

  2. NREL photovoltaic program FY 1997 annual report

    Energy Technology Data Exchange (ETDEWEB)

    McConnell, R.D.; Hansen, A.; Smoller, S.

    1998-06-01

    This report summarizes the in-house and subcontracted research and development (R and D) activities under the NREL PV Program from October 1, 1996, through September 30, 1997 (FY 1997). The NREL PV Program is part of the US Department of Energy`s (DOE`s) National Photovoltaics Program, as described in the DOE National Photovoltaics Program Plan for 1996--2000. The FY 1997 budget authority for carrying out the NREL PV Program was $39.3 million in operating funds and $0.4 million in capital equipment funds. Subcontract activities represent a major part of the NREL PV Program, with $21.8 million (55% of PV funds) going to some 84 subcontractors. Cost sharing by industry added almost $8.8 million to the subcontract R and D activities with industry.

  3. The motivation of subcontracted workers: a never-ending paradox La motivación de los trabajadores subcontratados. Una paradoja incesante

    Directory of Open Access Journals (Sweden)

    Alina Marcela Bustamente Salazar

    2010-12-01

    Full Text Available Certain considerations come about the subcontracted workers motivation when the Strategic Human Resource Management is used as a point of reference for diverse analysis. This article shows two faces of Human Resource Management. On one hand, the article indicates how important worker motivation has been for Human Resource Management and its direct association with worker productivity and efficacy. On the other hand, it points out the increasing importance that subcontracting has had as an alternative that allows companies the flexibilization and minimization of labor costs. Even though a structural contradiction comes up in this context, subcontracting seems to strive for feelings of affiliation and pride of belonging which are key elements to motivate the personnel. Apart from the literature review, the study was based on an ethnographic methodology of executives, contractors and subcontracted workers; and the results aim to contribute to streams of Organizational Theory and Human Resource Management.En el artículo se presentan consideraciones acerca de la motivación de los trabajadores subcontratados, en el marco de referencia de la “Gestión Humana Estratégica”. Se exponendos facetas de la administración de personal: por un lado, lo importante que ha sido lamotivación de los trabajadores para la Gestión Humana, como también la asociacióndirecta de esta con la productividad y la eficacia. Por otra parte, el auge creciente que hatenido la subcontratación como alternativa que permite a las empresas la flexibilizacióny minimización de sus costos laborales. Sin embargo, en este contexto, aparece unacontradicción estructural: la subcontratación parece atentar contra los sentimientos deafiliación y pertenencia organizacional, elementos claves para la motivación del personal.Además de la revisión documental, se llevó a cabo un trabajo etnometodológico conejecutivos, contratistas y empleados subcontratados. Los

  4. THE MOTIVATION BEHIND SUBCONTRACTING RELATIONSHIPS BETWEEN LARGE FIRMS AND SMALL AND MEDIUM ENTERPRISES IN THE MOTOR VEHICLE MANUFACTURING INDUSTRY IN KENYA

    Directory of Open Access Journals (Sweden)

    Beatrice Auko Okatch

    2011-07-01

    Full Text Available The motivation behind subcontracting relationships in the motor vehicle manufacturing The purpose of this study was to determine internal and external constraints to subcontracting arrangements between large firms and small and medium enterprises (SMEs in the motor vehicle manufacturing industry in Kenya in order to establish the reasons for the gap in those arrangements. The sector was chosen for the study because of the government’s selection of the sector to promote subcontracting arrangements between small and medium enterprises and large firms in Kenya. Secondly, the sector was chosen because of the complexity of the motor vehicle industry with one motor vehicle comprising about 10,000 component parts, all of which would be difficult for one company to manufacture in-house. The research was mainly qualitative but quantitative data was also used. Content analysis approach was used to analyze the qualitative data and descriptive statistics to analyze the quantitative data. Data was collected from two of the three motor vehicle assembles in Kenya, nine out of thirteen franchise holders and 66 of the 72 component parts suppliers who are mainly small and medium enterprises. The results indicate that the level of subcontracting that takes place in the motor vehicle manufacturing industry is minimal. This is motivated mainly by a desire to remain in the good books of the government. The big enterprises are not willing to buy component parts from local suppliers and especially not local SME suppliers mainly due to the inability of the SMEs to supply quality products to schedule, lack of local suppliers for certain parts, the proliferation of makes and models and competition from imported second hand vehicles from Japan and Europe. The proliferation of makes and models also requires frequent technological changes which both assemblers and SMEs owners find difficult to keep up with. The study recommends that the government should reduce the age of

  5. Areva subcontracts in Japan the noble part of the Finnish EPR; Areva sous-traite au Japon la partie noble de l'EPR finlandais

    Energy Technology Data Exchange (ETDEWEB)

    Jemain, A

    2004-02-01

    Areva, the French energy group, will subcontract the manufacturing of the reactor vessel and cover of the European Pressurized Reactor (EPR) which will be built in Finland. These components will be manufactured in Japan by Mitsubishi and not by Areva's Chalon/Saint-Marcel factory. The reason is the overburden of work and the lack of room and of machining equipment in the French factory. Also, the turbine and alternator are not built by Alstom, but by Siemens (Germany). (J.S.)

  6. Technology Development for High-Efficiency Solar Cells and Modules Using Thin (<80 um) Single-Crystal Silicon Wafers Produced by Epitaxy: June 11, 2011 - April 30, 2013

    Energy Technology Data Exchange (ETDEWEB)

    Ravi, T. S.

    2013-05-01

    Final technical progress report of Crystal Solar subcontract NEU-31-40054-01. The objective of this 18-month program was to demonstrate the viability of high-efficiency thin (less than 80 um) monocrystalline silicon (Si) solar cells and modules with a low-cost epitaxial growth process.

  7. Advanced Processing of CdTe- and CuInxGa1-xSe2-Based Solar Cells: Final Report: 18 April 1995 - 31 May 1998

    Energy Technology Data Exchange (ETDEWEB)

    Morel, D. L.; Ferekides, C. S.; Bhatt, R.; Jayapalan, A.; Komin, V.; Lin, H.; Marinskiy, D.; Marinskaya, S.; Narayanaswamy, R.; Poosarla, U; Prabhakaran, R.; Sankaranarayanan, H.; Tetali, B.; Viswanathan, V.; Zafar, S. (Department of Electrical Engineering: The University of South Florida: Tampa, Florida)

    1999-01-13

    This report summarizes work performed by the University of South Florida Department of Electrical Engineering under this subcontract. The Cadmium telluride(CdTe) portion of this project deals with the development of high-efficiency thin-filmed CdTe solar cells using fabrication techniques that are suitable for manufacturing environments.

  8. Post-Lamination Manufacturing Process Automation for Photovoltaic Modules: Final Subcontract Report, April 1998 - April 2002

    Energy Technology Data Exchange (ETDEWEB)

    Nowlan, M. J.; Murach, J. M.; Sutherland, S. F.; Miller, D. C.; Moore, S. B.; Hogan, S. J.

    2002-11-01

    This report describes the automated systems developed for PV module assembly and testing processes after lamination. These processes are applicable to a broad range of module types, including those made with wafer-based and thin-film solar cells. Survey data and input from module manufacturers gathered during site visits were used to define system capabilities and process specifications. Spire completed mechanical, electrical, and software engineering for four automation systems: a module edge trimming system, the SPI-TRIM 350; an edge sealing and framing system, the SPI-FRAMER 350; an integrated module testing system, the SPI-MODULE QA 350; and a module buffer storage system, the SPI-BUFFER 350. A fifth system for junction-box installation, the SPI-BOXER 350, was nearly completed during the program. A new-size solar simulator, the SPI-SUN SIMULATOR 350i, was designed as part of the SPI-MODULE QA 350. This simulator occupies minimal production floor space, and its test area is large enough to handle most production modules. The automated systems developed in this program are designed for integration to create automated production lines.

  9. Subcontracting relations and their effects on safety and security in two firms: SNCF and GrDF; Les relations de sous-traitance et leurs effets sur la surete et la securite dans deux entreprises: SNCF et GrDF

    Energy Technology Data Exchange (ETDEWEB)

    Ponnet, Marie

    2011-07-04

    Because of economical processes that tend to move the frontiers of firms salaried relations of uncertain status are found coexisting inside the very same working world. From a qualitative investigation mixing employees' interviews and observations made on SNCF and GrDF working sites our research offers to think about the relations linking subcontracting, maintenance, safety and security. Considering subcontracting as a particular way for professional bodies to be associated allows us to wonder about its effects within a same firm (the 'integrated' subcontracting) as much as between a principal and a provider. Our thesis shows that when change occurs inside the organization - like the creation of new committees of experts or the reorganizing of an old service - security and safety can be impacted because thus professional bodies tend to be reconfigured while modifications affect practices, professional identities and work division. The relations between subcontractors and principal are complicated and their consequences depend from the context they are placed in, determined by a combination of various characteristics such as the confidence level, the available time, the reputation, the position occupied by the subcontractor. Our investigation makes clear that there is no direct link between subcontracting, security and safety. Their effects, in spite of their reality, are submitted to the altering mediation of legal factors (related to economic national and European issues) and concern the working organization as well as the professional identities. (author)

  10. Module process optimization and device efficiency improvement for stable, low-cost, large-area, cadmium telluride-based photovoltaic module production. Final subcontract report, 1 July 1990--30 April 1994

    Energy Technology Data Exchange (ETDEWEB)

    Albright, S P; Johnson, S X [Golden Photon, Inc., CO (United States)

    1994-06-01

    This report describes work performed under a three-phase subcontract. The objectives of the program include (1) achievement of active-area efficiencies of greater than 14% on small cells; (2) achievement of aperture-area efficiencies of greater than 13% on 0.09-m{sup 2} (1 ft{sup 2}) modules; (3) achievement of aperture-area efficiencies of greater than 12.5% on 0.37-m{sup 2} (4 ft{sup 2}) modules; and achievement of greater than 20-year module life (based on life testing extrapolations) with no greater than 10% efficiency degradation. The results obtained and described herein include the following: (1) efficiencies of 12.7% were achieved on small-area devices; (2) 0.09-m{sup 2} (1 ft{sup 2}) modules achieved greater than 8% aperture-area efficiency, but work for further efficiency improvement was redirected toward the 0.37-M{sup 2} (4 if) modules; (3) 0.37-m{sup 2} (4 ft{sup 2}) modules achieved 26.5-W output, which calculates to 8.0% aperture-area efficiency; (4) consistent prototype production was focused on and substantially achieved within Phase 2; (5) life testing at the National Renewable Energy Laboratory showed no inherent stability problems with the CdTe technology, and the accuracy of module measurement was satisfactorily resolved; and (6) a ``cradle-to-cradle`` recycling program was begun based upon the philosophy that the establishment of such mechanisms will be required to ensure maximum recapture and recycling of all manufacturing waste materials and/or modules returned from the field.

  11. Annual Statistical Supplement, 2015

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2015 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  12. Annual Statistical Supplement, 2002

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2002 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  13. Annual Statistical Supplement, 2014

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2014 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  14. Annual Statistical Supplement, 2000

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2000 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  15. Annual Statistical Supplement, 2010

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2010 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  16. Annual Statistical Supplement, 2009

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2009 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  17. Annual Statistical Supplement, 2004

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2004 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  18. Annual Statistical Supplement, 2011

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2011 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  19. Annual Statistical Supplement, 2006

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2006 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  20. Annual Statistical Supplement, 2001

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2001 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  1. Annual Statistical Supplement, 2003

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2003 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  2. Annual Statistical Supplement, 2005

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2005 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  3. Annual Statistical Supplement, 2008

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2008 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  4. Annual Statistical Supplement, 2007

    Data.gov (United States)

    Social Security Administration — The Annual Statistical Supplement, 2007 includes the most comprehensive data available on the Social Security and Supplemental Security Income programs. More than...

  5. Advanced Therapy Medicinal Products: How to Bring Cell-Based Medicinal Products Successfully to the Market - Report from the CAT-DGTI-GSCN Workshop at the DGTI Annual Meeting 2014.

    Science.gov (United States)

    Celis, Patrick; Ferry, Nicolas; Hystad, Marit; Schüßler-Lenz, Martina; Doevendans, Pieter A; Flory, Egbert; Beuneu, Claire; Reischl, Ilona; Salmikangas, Paula

    2015-05-01

    On September 11, 2014, a workshop entitled 'Advanced Therapy Medicinal Products: How to Bring Cell-Based Medicinal Product Successfully to the Market' was held at the 47th annual meeting of the German Society for Transfusion Medicine and Immunohematology (DGTI), co-organised by the European Medicines Agency (EMA) and the DGTI in collaboration with the German Stem Cell Network (GSCN). The workshop brought together over 160 participants from academia, hospitals, small- or medium-sized enterprise developers and regulators. At the workshop, speakers from EMA, the Committee for Advanced Therapies (CAT), industry and academia addressed the regulatory aspects of development and authorisation of advanced therapy medicinal products (ATMPs), classification of ATMPs and considerations on cell-based therapies for cardiac repair. The open forum discussion session allowed for a direct interaction between ATMP developers and the speakers from EMA and CAT.

  6. Annual Energy Review, 2008

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-06-01

    The Annual Energy Review (AER) is the Energy Information Administration's (EIA) primary report of annual historical energy statistics. For many series, data begin with the year 1949. Included are statistics on total energy production, consumption, trade, and energy prices; overviews of petroleum, natural gas, coal, electricity, nuclear energy, renewable energy, and international energy; financial and environment indicators; and data unit conversions.

  7. Annual Report 1997

    Energy Technology Data Exchange (ETDEWEB)

    Golnik, N.; Mika, J.R.; Wieteska, K. [eds.

    1998-12-31

    This Annual Report of the Institute of Atomic Energy describes the results of the research works carried out at the Institute at 1997. As in the preceding years the authors of the individual scientific reports published in this Annual Report are fully responsible for their content and layout. The Report contains the information on other activities of the Institute as well. (author)

  8. Annual General Canvass Statistics

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains annual quantities and value for all seafood products that are landed and sold by established seafood dealers and brokers in the Southeast...

  9. Annual Trapping Proposal 1985

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This Annual Trapping Plan for the 1984-1985 trapping season at Clarence Cannon NWR outlines rules and regulations for the trapping of beaver and muskrat on the...

  10. USRDS - Annual Data Report

    Data.gov (United States)

    U.S. Department of Health & Human Services — United States Renal Data System (USRDS) Annual Data Report Comprehensive statistics on chronic kidney disease and end-stage renal diseases in the United States...

  11. 2010 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-01-01

    This annual report includes: an overview of Western; approaches for future hydropower and transmission service; major achievements in FY 2010; FY 2010 customer Integrated Resource Planning, or IRP, survey; and financial data.

  12. Annual General Meeting

    CERN Multimedia

    Staff Association

    2014-01-01

      STAFF ASSOCIATION Our next annual general meeting will take place on : Thursday 22 May 2014 at 11:00 AM Building 40-S2-D01 For further information visit our website : https://indico.cern.ch/event/313124/

  13. ASIST 2002 annual meeting

    CERN Multimedia

    Peek, R

    2003-01-01

    Review of discussions and presentations at the American Society for Information Science and Technology 2002 annual meeting. Topics covered included new models of scholarly publishing and the development of the semantic web (1 page).

  14. Annual Adjustment Factors

    Data.gov (United States)

    Department of Housing and Urban Development — The Department of Housing and Urban Development establishes the rent adjustment factors - called Annual Adjustment Factors (AAFs) - on the basis of Consumer Price...

  15. SIS - Annual Catch Limit

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Annual Catch Limit (ACL) dataset within the Species Information System (SIS) contains information and data related to management reference points and catch data.

  16. Natural gas annual 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-17

    The Natural Gas Annual provides information on the supply and disposition of natural gas to a wide audience including industry, consumers, Federal and State agencies, and educational institutions. The 1994 data are presented in a sequence that follows natural gas (including supplemental supplies) from its production to its end use. This is followed by tables summarizing natural gas supply and disposition from 1990 to 1994 for each Census Division and each State. Annual historical data are shown at the national level.

  17. Implemented organisation for subcontracting companies involved in the maintenance of the French nuclear stock - Sheet nr 39; Organisation mise en place pour les entreprises prestataires de la maintenance du parc nucleaire francais - Fiche No. 39

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-11-30

    Every year, some 20,000 subcontracted salaried employees are mobilised for maintenance operations in the French nuclear reactors. Subcontracting is an answer to different needs: specific abilities, the short delay for maintenance during which a reactor is stopped, and which requires a very important contribution of labour, and specialised labour for some interventions. The document evokes a rigorous selection and certification process, and indicates the different specific training which are organised for anyone intervening in a nuclear power plant. It outlines that radiation protection and safety arrangements are the same for all (dosimetry), and that some measurements are performed on some temporary workers. Some data shows that these controls are efficient and that safety is improving

  18. Determination Principle and Management Control on Subcontracting Management of Construction Enterprise%施工企业工程分包确定原则与管理控制

    Institute of Scientific and Technical Information of China (English)

    程文香; 范贵隆; 李宜忠

    2012-01-01

    目前,水利水电工程分包施工已是一种工程施工的方案,分包管理则是一个现代企业所必须具备的,其对分包的管理好坏,直接影响到企业的形象和利益.如何更好地做好分包工作的管理工作,最大限度地发挥分包施工的优势,最大能力地规避分包施工中的风险,是未来水利水电工程建设市场竞争的核心.详细介绍了工程分包确定原则和管理控制,并就分包管理中存在的问题进行探讨,并提出解决措施.%At present, construction subcontracting of construction of water conservancy and hydropower project is a construction program. Subcontracting management is necessary for all the modem enterprise, and its management of sub-quality directly affects corporation image and interests. How to do better management of subcontracting and maximize the advantages of sub-construction and the capacity to avoid the risk of sub-construction is the core for the future water conservancy and hydropower project construction market competition. The determination principle and management control are introduced, and some problems in the subcontracting management are discussed and the suggestions are given to solve these problems.

  19. Study on Quality Control for the Outsourcing of Acquisitioning and Catalogu-ing Subcontract of University Library%高校图书馆采编业务外包的质量控制研究

    Institute of Scientific and Technical Information of China (English)

    宋月

    2016-01-01

    文章研究了高校图书馆图书采编业务外包的起因,以及采编业务外包对高校图书馆业务的影响,提出有效控制采编业务外包质量的3个途径:正确选择书商、提升外包编目人员素质以及加强编目外包质量的监控,上述措施有效地控制了采编业务外包质量。%In this paper, the cause of the outsourcing of acquisitioning and cataloguing subcontract of university li-brary and its effect on university library were investigated. Three ways to effectively controlling quality of the outsourcing of acquisitioning and cataloguing subcontract was given, that is correct selection of bookseller, upgrad-ing the personnel quality of outsourcing and strengthening the quality control of cataloguing subcontract. All these can effectively control quality of the outsourcing services.

  20. Optimization of Phase-Engineered a-Si:H-Based Multi-Junction Solar Cells: Final Technical Report, October 2001-July 2005

    Energy Technology Data Exchange (ETDEWEB)

    Wronski, C. R.; Collins, R. W.; Podraza, N. J.; Vlahos, V.; Pearce, J. M.; Deng, J.; Albert, M.; Ferreira, G. M.; Chen, C.

    2006-08-01

    The scope of the work under this subcontract has involved investigating engineered improvements in the performance and stability of solar cells in a systematic way, which included the following four tasks: (1) Materials research and device development; (2) Process improvement directed by real time diagnostics; (3) Device loss mechanisms; and (4) Characterization strategies for advanced materials Our work has resulted in new and important insights into the deposition of a-Si:H-based materials, as well as into the nature of the Staebler-Wronski Effect (SWE). Presumably, many of these insights will be used by industrial partners to develop more systematic approaches in optimizing solar cells for higher performance and stability. This effort also cleared up several serious misconceptions about the nature of the p-layer in cells and the SWE in materials and cells. Finally, the subcontract identified future directions that should be pursued for greater understanding and improvement.

  1. Heterostructure single-crystal silicon photovoltaic cell. Type A, semiconductor heterojunction silicon devices. Annual report, September 28, 1976-November 30, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Ghosh, A.K.; Feng, T.; Fishman, C.

    1977-01-01

    Important electrical properties for the SnO/sub 2//Si heterostructure solar cell are summarized. The maximum theoretical efficiency and practically achievable efficiency are calculated. The method of fabricating the solar cell is described, and cost estimates and recommendations are given. A paper entitled SnO/sub 2//Si Solar Cells - Heterostructure or Schottky Barrier or MIS Type Device is appended which was previously abstracted for EDB. (LEW)

  2. An Industrial-Based Consortium to Develop Premium Carbon Products from Coal, Annual Progress Report, October 1, 2004 through September 30, 2005

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Bruce G

    2006-03-01

    Since 1998, The Pennsylvania State University (PSU) has been successfully operating the Consortium for Premium Carbon Products from Coal (CPCPC), which is a vehicle for industry-driven research on the promotion, development, and transfer of innovative technology on premium carbon produces from coal to the U.S. industry. The CPCPC is an initiative being led by PSU, its co-charter member West Virginia University (WVU), and the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL), who also provides the base funding for the program, with PSU responsible for consortium management. CPCPC began in 1998 under DOE Cooperative Agreement No. DE-FC26-98FT40350. This agreement ended November 2004 but the CPCPC activity has continued under the present cooperative agreement, No. DE-FC26-03NT41874, which started October 1, 2003. The objective of the second agreement is to continue the successful operation of the CPCPC. The CPCPC has enjoyed tremendous success with its organizational structure, that includes PSU and WVU as charter members, numerous industrial affiliate members, and strategic university affiliate members together with NETL, forming a vibrant and creative team for innovative research in the area of transforming coal to carbon products. The key aspect of CPCPC is its industry-led council that selects proposals submitted by CPCPC members to ensure CPCPC target areas have strong industrial support. A second contract was executed with DOE NETL starting in October 2003 to continue the activities of CPCPC. An annual funding meeting was held in October 2003 and the council selected ten projects for funding. Base funding for the projects is provided by NETL with matching funds from industry. Subcontracts were let from Penn State to the subcontractors on March 1, 2004. Nine of the ten projects have been completed and the final reports for these 2004 projects are attached. An annual funding meeting was held in November 2004 and the council

  3. Mean-annual erosion potential for Colorado and New Mexico

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — The U.S. Geological Survey Data Series provides raster data representing an estimate of the mean-annual erosion potential of a 30-meter raster cell in Colorado and...

  4. Final Report for PV Incubator Subcontract No. NEU-0-99010-09: March 29, 2010 - March 28, 2011

    Energy Technology Data Exchange (ETDEWEB)

    Pan, N.

    2012-04-01

    MicroLink has developed a process technology that will enable the manufacture of high-efficiency, low-cost, multijunction solar cells for use in concentrating photovoltaic (CPV) applications. The multijunction cells were fabricated using a novel low-temperature wafer bonding process. A triple-junction InGaP/GaAs/Ge tandem solar cell with efficiency of 30% at 1 sun AM1.5 illumination was fabricated by wafer bonding a dual-junction InGaP/GaAs cell to a single-junction Ge cell. Temperature cycling over the range -25 degrees C to +40 degrees C resulted in no degradation of cell performance. Triple junction InGaP/GaAs/Ge cells were mounted onto ceramic carriers and tested at concentrations up to 300 suns.

  5. Natural gas annual 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-10-01

    The Natural Gas Annual provides information on the supply and disposition of natural gas to a wide audience including industry, consumers, Federal and State agencies, and educational institutions. The 1997 data are presented in a sequence that follows natural gas (including supplemental supplies) from its production to its end use. This is followed by tables summarizing natural gas supply and disposition from 1993 to 1997 for each Census Division and each State. Annual historical data are shown at the national level. 27 figs., 109 tabs.

  6. International energy annual 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    The International Energy Annual presents an overview of key international energy trends for production, consumption, imports, and exports of primary energy commodities in over 220 countries, dependencies, and areas of special sovereignty. Also included are population and gross domestic product data, as well as prices for crude oil and petroleum products in selected countries. Renewable energy reported in the International Energy Annual includes hydroelectric power, geothermal, solar, and wind electric power, biofuels energy for the US, and biofuels electric power for Brazil. New in the 1996 edition are estimates of carbon dioxide emissions from the consumption of petroleum and coal, and the consumption and flaring of natural gas. 72 tabs.

  7. Process Development and Basic Studies of Electrochemically Deposited CdTe-Based Solar Cells; Annual Technical Report, Phase I: May 15, 1998 - May 14, 1999

    Energy Technology Data Exchange (ETDEWEB)

    Kaydanov, V.I.; Ohno, T.R.

    2000-08-25

    The project describes long-term research and development issues related to polycrystalline thin-film solar cells. The general research approach is based on combining activities aimed at improvement of cell performance and stability with activities aimed at increasing fundamental understanding of the properties of materials making up the cells: CdTe, CdS, multi-layer back contact, and transparent conducting oxide (TCO) front contact. The authors emphasize the relation between structural and electronic material properties and various processing procedures, as well as the microscopic mechanisms responsible for the cell performance and its degradation. Major results and conclusions of this project include: (1) Stress tests of the cells under various stress conditions revealed conditions providing the most severe degrading of different cell parameters; (2) Consecutive stress testing under different bias revealed some reversible effects; (3) Preliminary analysis of the data obtained demonstrated a significant role of electromigration of the charged defects/impurities; (4) Some new approaches for the cell characterization and the data analysis were developed and checked experimentally; (5) New stress test experiments were planned for continued studies of degradation mechanisms.

  8. Studies of Basic Electronic Properties of CdTe-Based Solar Cells and Their Evolution During Processing and Stress; Annual Technical Report, 1 November 2005 - 31 October 2006

    Energy Technology Data Exchange (ETDEWEB)

    Beach, J.; Seymour, F. H.; Kaydanov, V. I.; Ohno, T. R.

    2007-01-01

    We describe the results of our continuing study of deep electronic states controlling open-circuit voltage in CdTe/CdS thin-film solar cells (Task 1). The study includes: (1) analysis of factors affecting trap signatures derived from admittance spectroscopy and capacitance transients measurements, such as activation-energy capture cross-sections and trap-density estimates, and (2) comparative studies of cells received from four different sources and prepared with significant variations in cell structure and processing procedures.

  9. Research on high-bandgap materials and amorphous silicon-based solar cells. Annual technical report, 15 May 1995--15 May 1996

    Energy Technology Data Exchange (ETDEWEB)

    Schiff, E.A.; Gu, Q.; Jiang, L.; Rao, P. [Syracuse, New York, NY (United States)

    1997-01-01

    We have developed a technique based on electroabsorption measurements for obtaining quantitative estimates of the built-in potential in a-Si:H based heterostructure solar cells incorporating microcrystalline or a-SiC:Hp layers. This heterostructure problem has been a major limitation in application of the electroabsorption technique. The new technique only utilizes measurements from a particular solar cell, and is thus a significant improvement on earlier techniques requiring measurements on auxiliary films. Using this new electroabsorption technique, we confirmed previous estimates of V{sub bi} {approx} 1.0 V in a-Si:H solar cells with {open_quotes}conventional{close_quotes} intrinsic layers and either microcrystalline or a-SiC:Hp layers. Interestingly, our first measurements on high V{sub oc} cells grown with {open_quotes}high hydrogen dilution{close_quotes} intrinsic layers yield a much larger value for V{sub bi} {approx} 1.3 V. We speculate that these results are evidence for a significant interface dipole at the p/i heterostructure interface. Although we believe that interface dipoles rationalize several previously unexplained effects on a-Si:H based cells, they are not currently included in models for the operation of a-Si:H based solar cells.

  10. Final Report for PV Incubator Subcontract No. NAT-7-77015-05: October 19, 2007 - July 30, 2009

    Energy Technology Data Exchange (ETDEWEB)

    Pan, N.

    2012-04-01

    The Solar America Initiative (SAI) is intended to provide numerous technological routes towards a lower levelized cost of solar-generated electricity (LCOE). MicroLink's planned contribution towards the SAI is to provide a method of lowering the cost of GaAs-based solar cells, which are a major contributor to the cost of concentrator photovoltaic (CPV) modules. MicroLink's unique approach is to use an epitaxial liftoff (ELO) process to completely remove the active solar cell from the substrate while preserving the performance and yield of the cell. The substrate accounts for approximately half the cost of conventional, multijunction GaAs-based solar cells. By using ELO, the substrate can be reused several times for additional solar cell growths, thereby reducing the cost of multijunction solar cells by up to 50%. The achievement of high efficiency has significantly increased the acceptance of MicroLink Devices as a future supplier of high-efficiency dual-junction and IMM (inverted metamorphic) triple-junction ELO solar cells. MicroLink entered the SAI program with a 10% efficiency GaAs solar cell (1-sun AM 1.5) and finished the program with an NREL-verified IMM triple-junction ELO solar cell (1-sun AM 1.5).

  11. Annual report 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    The annual report from IKU (Continental Shelf Institute) in Norway deals with the market adjustment of research activities at the institute as a result of offshore cost-cutting policy in the petroleum industry. The market is about to shift focus from volume to competence. In practice, that means buying competence instead of project ideas or proposals

  12. Carolinas Communication Annual, 1998.

    Science.gov (United States)

    McLennan, David B.

    1998-01-01

    This 1998 issue of "Carolinas Communication Annual" contains the following articles: "Give Me That Old Time Religion?: A Study of Religious Themes in the Rhetoric of the Ku Klux Klan" (John S. Seiter); "The Three Stooges versus the Third Reich" (Roy Schwartzman); "Interdisciplinary Team Teaching: Implementing…

  13. Annual report 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    SaskPower`s mission is to meet the electrical needs of Saskatchewan residents in a reliable, safe, efficient and environmentally responsible manner. This annual report of the Corporation discusses new business focus; operations highlights; quality of life; management discussion and analysis; financial ratios; and a report of management. Financial information is also included.

  14. Annual Report 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    The Institut Laue-Langevin (ILL) is an international research center using neutrons to probe the microscopic structure and dynamics of a broad range of materials. This annual report presents the ILL activities in 2000: the scientific highlights, the Millennium programme and the new developments, the workshops organized by the ILL, the experimental programme and the publications. (A.L.B.)

  15. 2010 AAUW Annual Report

    Science.gov (United States)

    American Association of University Women, 2010

    2010-01-01

    This report highlights some of the outstanding accomplishments of AAUW (American Association of University Women) for fiscal year 2010. This year's annual report also features stories of remarkable women who are leading the charge to break through barriers and ensure that all women have a fair chance. Sharon is working to reduce the pay gap…

  16. NERSC Annual Report 2004

    Energy Technology Data Exchange (ETDEWEB)

    Hules, John; Bashor, Jon; Yarris, Lynn; McCullough, Julie; Preuss, Paul; Bethel, Wes

    2005-04-15

    The National Energy Research Scientific Computing Center (NERSC) is the premier computational resource for scientific research funded by the DOE Office of Science. The Annual Report includes summaries of recent significant and representative computational science projects conducted on NERSC systems as well as information about NERSC's current and planned systems and services.

  17. International Energy Annual, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-14

    This report is prepared annually and presents the latest information and trends on world energy production and consumption for petroleum, natural gas, coal, and electricity. Trade and reserves are shown for petroleum, natural gas, and coal. Prices are included for selected petroleum products. Production and consumption data are reported in standard units as well as British thermal units (Btu) and joules.

  18. UNICEF Annual Report. 1984.

    Science.gov (United States)

    United Nations Children's Fund, New York, NY.

    This annual report reviews the work UNICEF has been doing to help transform the "Child Survival Revolution" from a dream into a reality. Discussion focuses primarily on child health and nutrition and other basic services for children. Throughout, the review is supplemented with profiles of program initiatives made to improve the…

  19. Mail Office annual closure

    CERN Multimedia

    2013-01-01

    On the occasion of the annual closure of CERN, there will be no mail distributed on Friday 20 December 2013 but mail will be collected in the morning. Nevertheless, you will still be able to bring your outgoing mail to Building 555-R-002 until 12 noon.  

  20. Annual HR Salary Survey.

    Science.gov (United States)

    Schaeffer, Patricia

    2000-01-01

    A trainers' salary survey collected data on 1,091 companies, 31,615 employees, and 97 human resource jobs. Results show pay for human resource professionals is continuing to rise. The survey contains information on base salaries, annual bonuses and incentives, and long-term eligibility incentives. (JOW)

  1. NRCC annual report, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-11-01

    This annual report of the National Research for Computation in Chemistry (NRCC) Division describes the program of research workshops, software development, and scientific research of the Division in 1979. This year marked the first full calendar year of activity of the Division. Initial staffing in the core scientific areas was completed by the addition of a crystallographer.

  2. NERSC Annual Report 2002

    Energy Technology Data Exchange (ETDEWEB)

    Hules, John

    2003-01-31

    The National Energy Research Scientific Computing Center (NERSC) is the primary computational resource for scientific research funded by the DOE Office of Science. The Annual Report for FY2002 includes a summary of recent computational science conducted on NERSC systems (with abstracts of significant and representative projects), and information about NERSC's current and planned systems and service

  3. NERSC Annual Report 2005

    Energy Technology Data Exchange (ETDEWEB)

    Hules (Ed.), John

    2006-07-31

    The National Energy Research Scientific Computing Center (NERSC) is the premier computational resource for scientific research funded by the DOE Office of Science. The Annual Report includes summaries of recent significant and representative computational science projects conducted on NERSC systems as well as information about NERSC's current and planned systems and services.

  4. Uranium industry annual 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-04-22

    The Uranium Industry Annual 1998 (UIA 1998) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing. It contains data for the period 1989 through 2008 as collected on the Form EIA-858, ``Uranium Industry Annual Survey.`` Data provides a comprehensive statistical characterization of the industry`s activities for the survey year and also include some information about industry`s plans and commitments for the near-term future. Data on uranium raw materials activities for 1989 through 1998, including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment, are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2008, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, and uranium inventories, are shown in Chapter 2. The methodology used in the 1998 survey, including data edit and analysis, is described in Appendix A. The methodologies for estimation of resources and reserves are described in Appendix B. A list of respondents to the ``Uranium Industry Annual Survey`` is provided in Appendix C. The Form EIA-858 ``Uranium Industry Annual Survey`` is shown in Appendix D. For the readers convenience, metric versions of selected tables from Chapters 1 and 2 are presented in Appendix E along with the standard conversion factors used. A glossary of technical terms is at the end of the report. 24 figs., 56 tabs.

  5. 论建设工程项目专业分包的前期管理%On Management of Specialized Subcontract at Initial Stage of Construction Projects

    Institute of Scientific and Technical Information of China (English)

    黄晓幸

    2012-01-01

    As the competition in the domestic construction market is becoming increasingly fierce, profit margins are narrowed; specialized division of labor has been one of the characters of the industry itself. To improve the competitiveness of the construction company, the paper points out that the focus should be on improving the professional and technical standard as well as management level. The paper elaborates on the problems existing at the initial stage of the specialized subcontract which were easily overlooked and proposes measures to tackle the problems.%国内建筑市场竞争日益激烈,利润空间扁平化,分工专业化已是行业本身特点之一。施工企业在这种市场环境下若想提高自身生存能力,提高企业竞争力,其关注焦点应集中于提高专业技术水平和管理水平。针对建设工程项目专业分包前期易忽视的问题进行阐述,并提出拟采取的手段。

  6. New strategies for designing inexpensive but selective bioadsorbants for environmental pollutants: Selection of specific ligands and their cell surface expression. 1998 annual progress report

    Energy Technology Data Exchange (ETDEWEB)

    Iverson, B.L.; Georgiou, G. [Univ. of Texas, Austin, TX (US); Ataai, M.M.; Koepsel, R.R. [Univ. of Pittsburgh, PA (US)

    1998-06-01

    'The broad, long term objective of the research plan is to develop exquisitely selective polypeptide metal chelators for the remediation of aqueous systems. A variety of polypeptide chelators will be developed and optimized ranging from antibodies to small peptides. Then, through unique molecular engineering approaches developed in the laboratories, the polypeptide chelators will be anchored directly on the surface of the cells that produce them. Thus, instead of using isolated biomolecules the authors will employ inexpensive genetically engineered whole cell adsorbents. Following a simple, easily scaleable treatment, the engineered cells can be used to manufacture an inexpensive, particulate adsorbent for metal removal. The authors are currently in year two of a three year program. Work has been focused on preparing the molecular biology constructs needed to carry out the optimization of a metal complex binding antibody, and on the isolation of a metal binding peptide.'

  7. Electroabsorption and Transport Measurements and Modeling Research in Amorphous Silicon Based Solar Cells; Annual Report; 24 March 1999-23 March 2000

    Energy Technology Data Exchange (ETDEWEB)

    Schiff, E.A.; Kopidakis, N.; Lyou, J.; Rane, S.; Yuan, Q.; Zhu, K. (Syracuse University)

    2001-02-14

    We have performed computer calculations to explore effects of the p/i interface on the open-circuit voltage in a-Si:H based pin solar cells. The principal conclusions are that interface limitation can occur for values of VOC significantly below the built-in potential of VBI of a cell, and that the effects can be understood in terms of thermionic emission of electrons from the intrinsic layer into the p-layer. We compare measurements of VOC and electroabsorption estimates of VBI with the model calculations. We conclude that p/i interface limitation is important for current a-Si:H based cells, and that the conduction band offset between the p and i layers is as important as the built-in potential for future improvements to VOC.

  8. 1988 Annual water management plan

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Ruby Lake NWR 1987 Annual Water Management Report 1988 Annual Water Management Plan. Includes 1987 weather summary, water availability forecast, summary of 1987...

  9. Calendar Year 2004 annual site environmental report : Tonopah Test Range, Nevada & Kauai Test Facility, Hawaii.

    Energy Technology Data Exchange (ETDEWEB)

    Montoya, Amber L.; Wagner, Katrina; Goering, Teresa Lynn; Koss, Susan I.; Salinas, Stephanie A.

    2005-09-01

    Tonopah Test Range (TTR) in Nevada and Kauai Test Facility (KTF) in Hawaii are government-owned, contractor-operated facilities operated by Sandia Corporation, a subsidiary of Lockheed Martin Corporation. The U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA), through the Sandia Site Office (SSO), in Albuquerque, NM, manages TTR and KTF's operations. Sandia Corporation conducts operations at TTR in support of DOE/NNSA's Weapons Ordnance Program and has operated the site since 1957. Westinghouse Government Services subcontracts to Sandia Corporation in administering most of the environmental programs at TTR. Sandia Corporation operates KTF as a rocket preparation launching and tracking facility. This Annual Site Environmental Report (ASER) summarizes data and the compliance status of the environmental protection and monitoring program at TTR and KTF through Calendar Year (CY) 2004. The compliance status of environmental regulations applicable at these sites include state and federal regulations governing air emissions, wastewater effluent, waste management, terrestrial surveillance, and Environmental Restoration (ER) cleanup activities. Sandia Corporation is responsible only for those environmental program activities related to its operations. The DOE/NNSA, Nevada Site Office (NSO) retains responsibility for the cleanup and management of ER TTR sites. Currently, there are no ER Sites at KTF. Environmental monitoring and surveillance programs are required by DOE Order 450.1, Environmental Protection Program (DOE 2005) and DOE Order 231.1A, Environment, Safety, and Health Reporting (DOE 2004b).

  10. Petroleum marketing annual 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-24

    The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date.

  11. NAGRA Annual report 2010

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-04-15

    This annual report presents the highlights of the activities carried out by the Swiss National Co-operative for the Disposal of Radioactive Wastes NAGRA during the year 2010. These include reviews by various commissions of the NAGRA co-operative's proposals for possible sites for nuclear waste repositories. Also, the enhancements made concerning information facilities for the general public at the co-operative's rock laboratories are mentioned. The operation of initial satellite-based precision measurement systems for movements in the earth's crust is noted. Organisational aspects and international co-operation are discussed. This annual report also looks at NAGRA's organisational structures and its commercial accounts. Appendices provide details on waste inventories and volumes and publications made in 2010. A selection of relevant internet addresses is also provided

  12. Renewable energy annual 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    The Renewable Energy Annual 1995 is the first in an expected series of annual reports the Energy Information Administration (EIA) intends to publish to provide a comprehensive assessment of renewable energy. This report presents the following information on the history, status, and prospects of renewable energy data: estimates of renewable resources; characterizations of renewable energy technologies; descriptions of industry infrastructures for individual technologies; evaluations of current market status; and assessments of near-term prospects for market growth. An international section is included, as well as two feature articles that discuss issues of importance for renewable energy as a whole. The report also contains a number of technical appendices and a glossary. The renewable energy sources included are biomass (wood), municipal solid waste, biomass-derived liquid fuels, geothermal, wind, and solar and photovoltaic.

  13. Annual Energy Review 2007

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2008-06-01

    The Annual Energy Review (AER) is the Energy Information Administration's (EIA) primary report of annual historical energy statistics. For many series, data begin with the year 1949. Included are data on total energy production, consumption, and trade; overviews of petroleum, natural gas, coal, electricity, nuclear energy, renewable energy, international energy, as well as financial and environment indicators; and data unit conversion tables. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the EIA under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....”

  14. Coal industry annual 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs.

  15. Annual General Asssembly

    CERN Multimedia

    Pension Fund

    2005-01-01

    All members and beneficiaries of the Pension Fund are invited to attend the Annual General Asssembly to be held in the CERN Council Chamber on Thursday 13 October 2005 at 14:30 The Agenda comprises: Opening Remarks (J. Bezemer) Results and presentation of the Annual Report 2004 - Role of asset classes in pension funds (C. Cuénoud). Copies of the 2004 Report are available from departmental secretariats. Package of measures aiming at equilibrating the Fund - Proposals by the Governing Board (J.-P. Matheys). Questions from members and beneficiaries. Persons wishing to ask questions are encouraged to submit them, where possible, in writing in advance, addressed to Mr C. Cuénoud, Administrator of the Fund. Conclusions (J. Bezemer). As usual, participants are invited to drinks after the assembly. NB The minutes of the 2004 General Assembly are available from the Administration of the Fund (tel.(+4122)767 27 42; e-mail Sophia.Revol@cern.ch)

  16. Annual General Asssembly

    CERN Multimedia

    2005-01-01

    All members and beneficiaries of the Pension Fund are invited to attend the Annual General Asssembly to be held in the CERN Council Chamber on Thursday 13 October 2005 at 14:30 The Agenda comprises: Opening Remarks (J. Bezemer) Results and presentation of the Annual Report 2004 - Role of asset classes in pension funds (C. Cuénoud) Copies of the 2004 Report are available from departmental secretariats. Package of measures aiming at equilibrating the Fund - Proposals by the Governing Board (J.-P. Matheys) Questions from members and beneficiaries Persons wishing to ask questions are encouraged to submit them, where possible, in writing in advance, addressed to Mr C. Cuénoud, Administrator of the Fund. Conclusions (J. Bezemer) As usual, participants are invited to drinks after the assembly. NB The minutes of the 2004 General Assembly are available from the Administration of the Fund (tel.(+4122)767 27 42; e-mail Sophia.Revol@cern.ch)

  17. International energy annual 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-04-01

    The International Energy Annual presents an overview of key international energy trends for production, consumption, imports, and exports of primary energy commodities in over 220 countries, dependencies, and areas of special sovereignty. Also included are population and gross domestic product data, as well as prices for crude oil and petroleum products in selected countries. Renewable energy reported in the International Energy Annual includes hydroelectric power and geothermal, solar, and wind electric power. Also included are biomass electric power for Brazil and the US, and biomass, geothermal, and solar energy produced in the US and not used for electricity generation. This report is published to keep the public and other interested parties fully informed of primary energy supplies on a global basis. The data presented have been largely derived from published sources. The data have been converted to units of measurement and thermal values (Appendices E and F) familiar to the American public. 93 tabs.

  18. Study of the radiation effects on nucleic acids and related compounds. Annual progress report, August 15, 1974--August 14, 1975. [X radiation, hamster cells, Haemophilus influenzae

    Energy Technology Data Exchange (ETDEWEB)

    Wang, S.Y.

    1975-01-01

    Interest is being centered on the chemical and physical nature of radiation-induced lesions to nucleic acids and their components. These investigations have revealed the enormous complexity of chemical events in these systems and the possible degradation of nucleic acids by strand breakage. Therefore, work in the ionizing radiation of DNA and its components has proceeded along a dual course. For chemical studies, our prime concern is the stepwise isolation and identification of the radiation products of derivatives of pyrimidines and the study of the actual mechanisms of their formation. For biological studies, H. influenzae cells, the Chinese hamster V79B-1 cell line, and the Dunn osteosarcoma lung colony system were used. During the last year, the method of synthesis of 5-hydroperoxymethyluracil (T/sub ..cap alpha../OOH) was greatly improved. Large-scale preparation of 5-hydroxy-6-hydroperoxy-5,6-dihydrothymine (T/sup 6/OOH) were carried out in order to study the action of T/sup 6/OOH on neighboring bases, glycosidic bond-breakage, cell mutagenesis, chromosomal aberrations, and possible synergistic effects on x radiation. These results allow one to relate radiobiological effects with radiation chemical changes in DNA.

  19. TIARA annual report 1999

    Energy Technology Data Exchange (ETDEWEB)

    Saidoh, Masahiro; Toraishi, Akio; Itoh, Hisayoshi [eds.] [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment] [and others

    2000-10-01

    This annual report describes research and development activities which have been performed with the JAERI TIARA (Takasaki Ion Accelerators for Advanced Radiation Application) facilities from April 1, 1999 to March 31, 2000. Summary reports of 106 papers and brief descriptions on the status of TIARA in the period are contained. A list of publications, the type of research collaborations and organization of TIARA are also given as appendices. (author)

  20. 2008 annual merit review

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2009-01-18

    The 2008 DOE Vehicle Technologies Program Annual Merit Review was held February 25-28, 2008 in Bethesda, Maryland. The review encompassed all of the work done by the Vehicle Technologies Program: a total of 280 individual activities were reviewed, by a total of just over 100 reviewers. A total of 1,908 individual review responses were received for the technical reviews, and an additional 29 individual review responses were received for the plenary session review.

  1. NSLS annual report 1984

    Energy Technology Data Exchange (ETDEWEB)

    Klaffky, R.; Thomlinson, W. (eds.)

    1984-01-01

    The first comprehensive Annual Report of the National Synchrotron Light Source comes at a time of great activity and forward motion for the facility. In the following pages we outline the management changes that have taken place in the past year, the progress that has been made in the commissioning of the x-ray ring and in the enhanced utilization of the uv ring, together with an extensive discussion of the interesting scientific experiments that have been carried out.

  2. TIARA annual report 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    This annual report describes research activities which have been performed with the JAERI TIARA (Takasaki Ion Accelerators for Advanced Radiation Application) facilities from April 1, 1996 to March 31, 1997. Summary reports of 88 papers and 4 brief descriptions on the status of TIARA in the period are contained. A list of publications, the type of research collaborations and organization of TIARA are also given as appendices. (J.P.N.)

  3. TIARA annual report 2000

    Energy Technology Data Exchange (ETDEWEB)

    Saidoh, Masahiro; Toraishi, Akio; Namba, Hideki (eds.) [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment] [and others

    2001-11-01

    This annual report describes research and development activities which have been performed with the JAERI TIARA (Takasaki Ion Accelerators for Advanced Radiation Application) facilities from April 1, 2000 to March 31, 2001. Summary reports of 103 papers and brief descriptions on the status of TIARA in the period are contained. A list of publications, the type of research collaborations and organization of TIARA are also given as appendices. (author)

  4. Annual Pension Fund Update

    CERN Multimedia

    Pension Fund

    2011-01-01

    All members and beneficiaries of the Pension Fund are invited to attend the Annual Pension Fund Update to be held in the CERN Council Chamber on Tuesday 20 September 2011 from 10-00 to 12-00 a.m. Copies of the 2010 Financial Statements are available from departmental secretariats. Coffee and croissants will be served prior to the meeting as of 9-30 a.m.

  5. TIARA annual report 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    This annual report describes research and development activities which have been performed with the JAERI TIARA (Takasaki Ion Accelerators for Advanced Radiation Application) facilities from April 1, 1998 to March 31, 1999. Summary reports of 95 papers and brief descriptions on the status of TIARA in the period are contained. A list of publications, the type of research collaborations and organization of TIARA are also given as appendices. (author)

  6. TIARA annual report 2001

    Energy Technology Data Exchange (ETDEWEB)

    Saidoh, Masahiro; Ohara, Yoshihiro; Namba, Hideki (eds.) [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment] [and others

    2002-11-01

    This annual report describes research and development activities which have been performed with the JAERI TIARA (Takasaki Ion Accelerators for Advanced Radiation Application) facilities from April 1, 2001 to March 31, 2002. Summary reports of 109 papers and brief descriptions on the status of TIARA in the period are contained. A list of publications, the type of research collaborations and organization of TIARA are also given as appendices. (author)

  7. NERSC 1998 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Hules, John (ed.)

    1999-03-01

    This 1998 annual report from the National Scientific Energy Research Computing Center (NERSC) presents the year in review of the following categories: Computational Science; Computer Science and Applied Mathematics; and Systems and Services. Also presented are science highlights in the following categories: Basic Energy Sciences; Biological and Environmental Research; Fusion Energy Sciences; High Energy and Nuclear Physics; and Advanced Scientific Computing Research and Other Projects.

  8. Uranium industry annual 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    The Uranium Industry Annual 1995 (UIA 1995) provides current statistical data on the U.S. uranium industry`s activities relating to uranium raw materials and uranium marketing. The UIA 1995 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. It contains data for the period 1986 through 2005 as collected on the Form EIA-858, ``Uranium Industry Annual Survey``. Data collected on the ``Uranium Industry Annual Survey`` provide a comprehensive statistical characterization of the industry`s plans and commitments for the near-term future. Where aggregate data are presented in the UIA 1995, care has been taken to protect the confidentiality of company-specific information while still conveying accurate and complete statistical data. Data on uranium raw materials activities for 1986 through 1995 including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2005, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, uranium imports and exports, and uranium inventories are shown in Chapter 2. The methodology used in the 1995 survey, including data edit and analysis, is described in Appendix A. The methodologies for estimation of resources and reserves are described in Appendix B. A list of respondents to the ``Uranium Industry Annual Survey`` is provided in Appendix C. For the reader`s convenience, metric versions of selected tables from Chapters 1 and 2 are presented in Appendix D along with the standard conversion factors used. A glossary of technical terms is at the end of the report. 14 figs., 56 tabs.

  9. Annual report 1991

    Energy Technology Data Exchange (ETDEWEB)

    Broda, R.; Lesniak, L.; Malecki, P.; Stachura, Z.; Wojciechowski, H. [eds.

    1992-12-31

    The material presented describing the scientific activities of the Henryk Niewodniczanski Institute of Nuclear Physics in 1991 is the first annual report in several years.The arrangement of the report from various departments reflect the present structure of the Institute and is meant to help in the future task of reconstructing the Institute. Few guidelines proposed by the editorial board gave the individual departments much freedom in selecting the material and choosing the volume and format of presentation. (author).

  10. TIARA annual report 1997

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Ryuichi; Saido, Masahiro; Nashiyama, Isamu [eds.] [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment] [and others

    1998-10-01

    This annual report describes research activities which have been performed with the JAERI TIARA (Takasaki Ion Accelerators for Advanced Radiation Application) facilities from April 1, 1997 to March 31, 1998. Summary reports of 90 papers and brief descriptions on the status of TIARA in the period are contained. A list of publications, the type of research collaborations and organization of TIARA are also given as appendices. (author)

  11. Process Development for High Voc CdTe Solar Cells

    Energy Technology Data Exchange (ETDEWEB)

    Ferekides, C. S.; Morel, D. L.

    2011-05-01

    This is a cumulative and final report for Phases I, II and III of this NREL funded project (subcontract # XXL-5-44205-10). The main research activities of this project focused on the open-circuit voltage of the CdTe thin film solar cells. Although, thin film CdTe continues to be one of the leading materials for large-scale cost-effective production of photovoltaics, the efficiency of the CdTe solar cells have been stagnant for the last few years. This report describes and summarizes the results for this 3-year research project.

  12. Uranium industry annual 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-05

    The Uranium Industry Annual 1994 (UIA 1994) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing during that survey year. The UIA 1994 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. It contains data for the 10-year period 1985 through 1994 as collected on the Form EIA-858, ``Uranium Industry Annual Survey.`` Data collected on the ``Uranium Industry Annual Survey`` (UIAS) provide a comprehensive statistical characterization of the industry`s activities for the survey year and also include some information about industry`s plans and commitments for the near-term future. Where aggregate data are presented in the UIA 1994, care has been taken to protect the confidentiality of company-specific information while still conveying accurate and complete statistical data. A feature article, ``Comparison of Uranium Mill Tailings Reclamation in the United States and Canada,`` is included in the UIA 1994. Data on uranium raw materials activities including exploration activities and expenditures, EIA-estimated resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities, including purchases of uranium and enrichment services, and uranium inventories, enrichment feed deliveries (actual and projected), and unfilled market requirements are shown in Chapter 2.

  13. Alternative window schemes for CuInSe{sub 2}-based solar cells. Annual report, 1 November 1995--31 October 1996

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, L.C. [Washington State Univ., Richland, WA (United States). Electronic Materials Lab.

    1997-10-01

    The objectives of this program are to develop alternate heterojunction partner layers (buffer layers) for high efficiency CuInSe{sub 2}-based thin-film solar cells, and improve the understanding of how these layers and the details of processing affect cell performance. Investigations have primarily involved three tasks: (1) MOCVD growth of non-cadmium containing buffer layers; (2) optimized processing of buffer layers for high efficiency solar cells; and (3) electrical and physical characterization of layers and devices. Investigations of alternative buffer layers emphasized studies of ZnO grown by MOCVD. Using CIS substrates obtained form Siemens for process development, it was determined that growth procedures that resulted in good results with Siemens CIS (non-sulfur containing material) substrates also worked well with NREL CIGS material. A two step process was developed for growing highly resistive ZnO buffer layers (i-ZnO). In particular, after growing 100 to 150 {angstrom} of ZnO at 250 C, an additional 600 {angstrom} to 800 {angstrom} were grown at 100 C. Collaboration with NREL resulted in a n-ZnO/i-ZnO/CIGS cell which was determined to have a total area efficiency of 12.7%, and an active area efficiency greater than 13%. After growing i-ZnO with the two-step process onto NREL CIGS material, the i-ZnO/CIGS film structure was sent to NREL for deposition of a TCO, namely, conducting ZnO (n-ZnO). Collector grids and a MgF{sub 2} AR coating were also deposited at NREL. Low level efforts were devoted to studies of ZnSe and InSe buffer layers. A total area efficiency of 9.5% was achieved for a completed ZnSe/CIS cell making use of a RF sputtered ZnO for a TCO. Investigations of In{sub x}Se{sub y} (InSe) buffer layers were also initiated this past year.

  14. Solvent-refined-coal (SRC) process: health programs. Research and development report No. 53, Interim report No. 39. Volume III. Pilot plant development work. Part 4: Industrial hygiene, clinical and toxicological programs. Final report of subcontract No. 10, June 1, 1976-June 9, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1981-11-01

    This report summarizes the toxicological studies on SRC-I materials completed under Subcontract No. 10 as part of the Health Programs under the Solvent Refined Coal (SRC) Process Contract during the total period of the subcontract, June 1, 1976 through June 9, 1978. The studies were conducted by Industrial Bio-Test Laboratories (IBT) as the subcontractor. A number of acute studies were completed on the products and intermediate streams as well as several subchronic studies. In addition, preliminary dose-ranging, or pilot, studies were completed. None of the materials exhibited high toxicities when administered orally, dermally, or by the inhalation route. Three of the materials proved to be severely or extremely irritating to the eyes. The pilot dermal and teratogenesis studies revealed some evidence of decreased viability in offspring and reduced fetal body weights. The subcontract was terminated for convenience on June 9, 1978 when it became apparent that IBT could not satisfactorily continue the studies.

  15. 78 FR 64912 - Annual Retail Trade Survey

    Science.gov (United States)

    2013-10-30

    ... survey, the Census Bureau will collect data covering annual sales, annual e-commerce sales, year-end... Classification System (NAICS). ARTS provides, on a comparable classification basis, annual sales, annual e... annual sales, annual e-commerce sales, year-end inventories held inside and outside the United...

  16. Material growth and characterization directed toward improving iii-v heterojunction solar cells. Annual report, 1 February 1978 - 31 January 1979

    Energy Technology Data Exchange (ETDEWEB)

    Stefanakos, E.K.; Alexander, W.E.; Collis, W.; Abul-Fadl, A.

    1979-01-31

    In addition to the existing materials growth laboratory, the photolithographic facility and the device testing facility were completed. The majority of equipment for data acquisition, solar cell testing, materials growth and device characterization were received and are being put into operation. In the research part of the program, GaAs and GaA1As layers were grown reproducibly on GaAs substrates. These grown layers were characterized as to surface morphology, thickness and thickness uniformity. The liquid phase epitaxial growth process was used to fabricate p-n junctions in Ga(1-x)A1(x)As. Sequential deposition of two alloy layers was accomplished and detailed analysis of the effect of substrate quality and dopant on the GaA1As layer quality is presented. Finally, solar cell structures were formed by growing a thin p-GaA1As layer upon an epitaxial n-GaA1As layer. The energy gap corresponding to the long wavelength cutoff of the spectral response characteristic was 1.51-1.63 eV. Theoretical calculations of the spectral response were matched to the measured response.

  17. 不耐烦行为生产库存系统最优生产和分包控制%Optimal Production and Subcontracting Control in a Production-Inventory System with Impatient Behavior

    Institute of Scientific and Technical Information of China (English)

    王康周; 江志斌; 李娜; 李国威

    2012-01-01

    We present the optimal production and subcontracting control in a production-inventory system with balking. If there are backorders and the estimated waiting time is greater than the maximum delay he expected, an arriving customer may refuse to place the order and leave system immediately. Manager regulates system by two thresholds, base stock level and base subcontracting level. We model the dynamics of the system as a Markov chain and then give the numerical analysis. We find that, for the systems with strategic customers, subcontracting may enhance profit even though subcontracting cost is higher than lost sales cost. Managerial insights are proposed lastly.%研究了具有止步行为不耐烦顾客的生产库存系统的生产和分包控制问题.当顾客到达时,若有订单积压,则有部分顾客由于预期等待时间过长而放弃购买后离开系统,形成订单损失成本.在综合考虑订单收益和各种成本的基础上,企业通过基本库存水平和基本分包水平两个阈值对系统进行控制,以实现整体利润最大.建立了系统的Markov模型,得到系统稳态概率和性能指标,证明了最优库存水平和最优分包阈值的存在性及取值范围,并设计了搜索算法.利用他们对系统进行了数值分析.我们发现,基本库存基本分包控制策略下的系统性能优于基本库存策略下的系统性能.而且,即使当生产分包成本大于订单损失成本时,企业选择生产分包仍有可能获得收益.

  18. Microstructure of amorphous-silicon-based solar cell materials by small-angle x-ray scattering. Annual technical report, April 6, 1995--April 5, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Williamson, D.L. [Colorado School of Mines, Golden, CO (United States)

    1996-08-01

    The objective of this project is to provide detailed microstructural information on the amorphous silicon based thin film materials under development for improved multijunction solar cells. Correlation of microstructure with opto-electrical properties and device performance is an integral part of the research. During this second phase of our three-year program we have obtained information on the microstructure of materials relevant to the Low-, Mid-, and High-bandgap Teams and the results are appropriately divided into these three types of material as presented below. The experimental methods, data analysis, and interpretation procedures are the same as those described in detail in the phase-one report and in the review paper published last year.

  19. Renewable energy annual 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report presents summary data on renewable energy consumption, the status of each of the primary renewable technologies, a profile of each of the associated industries, an analysis of topical issues related to renewable energy, and information on renewable energy projects worldwide. It is the second in a series of annual reports on renewable energy. The renewable energy resources included in the report are biomass (wood and ethanol); municipal solid waste, including waste-to-energy and landfill gas; geothermal; wind; and solar energy, including solar thermal and photovoltaic. The report also includes various appendices and a glossary.

  20. Annual Energy Review 2010

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-10-01

    This twenty-ninth edition of the Annual Energy Review (AER) presents the U.S. Energy Information Administration’s (EIA) most comprehensive look at integrated energy statistics. The summary statistics on the Nation’s energy production, consumption, trade, stocks, and prices cover all major energy commodities and all energy-consuming sectors of the U.S. economy from 1949 through 2010. The AER is EIA’s historical record of energy statistics and, because the coverage spans six decades, the statistics in this report are well-suited to long-term trend analysis.

  1. Institute annual report 2004

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    The mission of the ITU (Institute for Transuranium Elements) is to protect the European citizen against risk associated with the handling and storage of highly radioactive elements. The JRC (Joint Research Center) provide customer-driven scientific and technical support for the conception, development, implementation and monitoring of EU policies. In this framework this annual report presents the TU actions in: basic actinide research, spent fuel characterization, safety of nuclear fuels, partitioning and transmutation, alpha-immunotherapy/radiobiology, measurement of radioactivity in the environment, safeguards research and development. (A.L.B.)

  2. Nordel annual report 2003

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-06-01

    Nordel is a body for co-operation between the transmission system operators (TSO's) in Denmark, Finland, Iceland, Norway and Sweden with the primary objective to create conditions for and develop an efficient and harmonised Nordic electricity market, regardless of national borders. Furthermore, Nordel serves as forum for contact between the TSOs and representatives of the market players in the Nordic countries. The statistical part of Nordel's annual report includes data about: Exchange of electricity; Gross consumption; Electricity generation; Installed capacity; Generation of condensing power; Net consumption; Transmission capacity; Pumped storage power; Losses; Occasional power to electric boilers; Total consumption; CHP generation. (BA)

  3. NPL 1999 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2000-01-01

    OAK-B135 NPL 1999 Annual Report. The Nuclear Physics Laboratory at the University of Washington in Seattle pursues a broad program of nuclear physics research. Research activities are conducted locally and at remote sites. The current program includes ''in-house'' research on nuclear collisions using the local tandem Van de Graaff and superconducting linac accelerators as well as local and remote non-accelerator research on fundamental symmetries and weak interactions and user-mode research on relativistic heavy ions at large accelerator facilities around the world.

  4. Annual Energy Review 2001

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2002-11-01

    The Annual Energy Review (AER) is a statistical history of energy activities in the United States. It documents trends and milestones in U.S. energy production, trade, storage, pricing, and consumption. Each new year of data that is added to the time series—which now reach into 7 decades—extends the story of how Americans have acquired and used energy. It is a story of continual change as the Nation's economy grew, energy requirements expanded, resource availability shifted, and interdependencies developed among nations.

  5. International energy annual 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    The International Energy Annual presents information and trends on world energy production and consumption for petroleum, natural gas, coal, and electricity. Production and consumption data are reported in standard units as well as British thermal units (Btu). Trade and reserves are shown for petroleum, natural gas, and coal. Data are provided on crude oil refining capacity and electricity installed capacity by type. Prices are included for selected crude oils and for refined petroleum products in selected countries. Population and Gross Domestic Product data are also provided.

  6. NERSC 2001 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Hules, John (editor)

    2001-12-12

    The National Energy Research Scientific Computing Center (NERSC) is the primary computational resource for scientific research funded by the DOE Office of Science. The Annual Report for FY2001 includes a summary of recent computational science conducted on NERSC systems (with abstracts of significant and representative projects); information about NERSC's current systems and services; descriptions of Berkeley Lab's current research and development projects in applied mathematics, computer science, and computational science; and a brief summary of NERSC's Strategic Plan for 2002-2005.

  7. Annual Energy Review 2009

    Energy Technology Data Exchange (ETDEWEB)

    Fichman, Barbara T. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2010-08-01

    The Annual Energy Review (AER) is the U.S. Energy Information Administration's (EIA) primary report of annual historical energy statistics. For many series, data begin with the year 1949. Included are statistics on total energy production, consumption, trade, and energy prices; overviews of petroleum, natural gas, coal, electricity, nuclear energy, renewable energy, and international energy; financial and environment indicators; and data unit conversions. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the EIA under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding the content of the AER and other EIA publications.

  8. Annual Energy Review 2011

    Energy Technology Data Exchange (ETDEWEB)

    Fichman, Barbara T. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2012-09-01

    The Annual Energy Review (AER) is the U.S. Energy Information Administration's (EIA) primary report of annual historical energy statistics. For many series, data begin with the year 1949. Included are statistics on total energy production, consumption, trade, and energy prices; overviews of petroleum, natural gas, coal, electricity, nuclear energy, and renewable energy; financial and environment indicators; and data unit conversions. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the EIA under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding the content of the AER and other EIA publications.

  9. Annual Energy Review 2005

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2006-07-01

    The Annual Energy Review (AER) is the Energy Information Administration's (EIA) primary report of annual historical energy statistics. For many series, data begin with the year 1949. Included are data on total energy production, consumption, and trade; overviews of petroleum, natural gas, coal, electricity, nuclear energy, renewable energy, international energy, as well as financial and environment indicators; and data unit conversion tables. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the EIA under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the AER and in other EIA publications.

  10. Annual Energy Review 2006

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2007-06-01

    The Annual Energy Review (AER) is the Energy Information Administration's (EIA) primary report of annual historical energy statistics. For many series, data begin with the year 1949. Included are data on total energy production, consumption, and trade; overviews of petroleum, natural gas, coal, electricity, nuclear energy, renewable energy, international energy, as well as financial and environment indicators; and data unit conversion tables. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the EIA under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the AER and in other EIA publications.

  11. CMS Annual Report 2004

    Energy Technology Data Exchange (ETDEWEB)

    de la Rubia, T D; Shang, S P; Rennie, G; Fluss, M; Westbrook, C

    2005-07-29

    Glance at the articles in this report, and you will sense the transformation that is reshaping the landscape of materials science and chemistry. This transformation is bridging the gaps among chemistry, materials science, and biology--ushering in a wealth of innovative technologies with broad scientific impact. The emergence of this intersection is reinvigorating our strategic investment into areas that build on our strength of interdisciplinary science. It is at the intersection that we position our strategic vision into a future where we will provide radical materials innovations and solutions to our national-security programs and other sponsors. Our 2004 Annual Report describes how our successes and breakthroughs follow a path set forward by our strategic plan and four organizing research themes, each with key scientific accomplishments by our staff and collaborators. We have organized this report into two major sections: research themes and our dynamic teams. The research-theme sections focus on achievements arising from earlier investments while addressing future challenges. The dynamic teams section illustrates the directorate's organizational structure of divisions, centers, and institutes that support a team environment across disciplinary and institutional boundaries. The research presented in this annual report gives substantive examples of how we are proceeding in each of these four theme areas and how they are aligned with our national-security mission. By maintaining an organizational structure that offers an environment of collaborative problem-solving opportunities, we are able to nurture the discoveries and breakthroughs required for future successes.

  12. Annual Energy Review 1993

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-14

    This twelfth edition of the Annual Energy Review (AER) presents the Energy Information Administration`s historical energy statistics. For most series, statistics are given for every year from 1949 through 1993. Because coverage spans four and a half decades, the statistics in this report are well-suited to long-term trend analyses. The AER is comprehensive. It covers all major energy activities, including consumption, production, trade, stocks, and prices, for all major energy commodities, including fossil fuels and electricity. The AER also presents Energy Information Administration (EIA) statistics on some renewable energy sources. EIA estimates that its consumption series include about half of the renewable energy used in the United States. For a more complete discussion of EIA`s renewables data, see p. xix, ``Introducing Expanded Coverage of Renewable Energy Data Into the Historical Consumption Series.`` Copies of the 1993 edition of the Annual Energy Review may be obtained by using the order form in the back of this publication. Most of the data in the 1993 edition also are available on personal computer diskette. For more information about the diskettes, see the back of this publication. In addition, the data are available as part of the National Economic, Social, and Environmental Data Bank on a CD-ROM. For more information about the data bank, contact the US Department of Commerce Economics and Statistics Administration, on 202-482-1986.

  13. Annual Energy Review 2004

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2005-08-01

    The Annual Energy Review (AER) is the Energy Information Administration's (EIA) primary report of annual historical energy statistics. For many series, data begin with the year 1949. Included are data on total energy production, consumption, and trade; overviews of petroleum, natural gas, coal, electricity, nuclear energy, renewable energy, international energy, as well as financial and environment indicators; and data unit conversion tables. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the EIA under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the AER and in other EIA publications.

  14. Electric power annual 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-06

    The Electric Power Annual presents a summary of electric utility statistics at national, regional and State levels. The objective of the publication is to provide industry decisionmakers, government policymakers, analysts and the general public with historical data that may be used in understanding US electricity markets. The Electric Power Annual is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels; Energy Information Administration (EIA); US Department of Energy. ``The US Electric Power Industry at a Glance`` section presents a profile of the electric power industry ownership and performance, and a review of key statistics for the year. Subsequent sections present data on generating capability, including proposed capability additions; net generation; fossil-fuel statistics; retail sales; revenue; financial statistics; environmental statistics; electric power transactions; demand-side management; and nonutility power producers. In addition, the appendices provide supplemental data on major disturbances and unusual occurrences in US electricity power systems. Each section contains related text and tables and refers the reader to the appropriate publication that contains more detailed data on the subject matter. Monetary values in this publication are expressed in nominal terms.

  15. ANNUAL GENERAL ASSEMBLY

    CERN Multimedia

    2001-01-01

    All members and beneficiaries of the Pension Fund are invited to attend the Annual General Asssembly to be held in the CERN Auditorium on Wednesday 3 October 2001 at 14.30 hrs The Agenda comprises:   Opening Remarks (P. Levaux) Some aspects of risk in a pension fund (C. Cuénoud) Annual Report 2000: Presentation and results (C. Cuénoud) Copies of the Report are available from divisional secretariats. Results of the actuarial reviews (G. Maurin) Questions from members and beneficiaries Persons wishing to ask questions are encouraged to submit them, where possible, in writing in advance, addressed to Mr C. Cuénoud, Administrator of the Fund. Conclusions (P. Levaux) As usual, participants are invited to drinks after the assembly. NB The minutes of the 2000 General Assembly are available from the Administration of the Fund (tel. + 41 22 767 91 94; e-mail Graziella.Praire@cern.ch) The English version will be published next week.

  16. Nuclear Physics Department annual report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    This annual report presents articles and abstracts published in foreign journals, covering the following subjects: nuclear structure, nuclear reactions, applied physics, instrumentation, nonlinear phenomena and high energy physics

  17. Areva, annual report 2004

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    This annual report contains information on AREVA objectives, prospects and strategies, particularly in chapters 4 and 7. This information is a not meant as a presentation of past performance data and should not be interpreted as a guarantee that events or data set forth herein are assured or that objectives will be met. Forward looking statements made in this document also address known and unknown risks, uncertainties and other factors that could, were they to translate into fact, cause AREVA future financial performance, operating performance and production to differ significantly from the objectives presented or suggested herein. Those factors include, in particular, changes in international, economic or market conditions, as well as risk factors presented in Section 4.14.3. Neither AREVA nor the AREVA group is committing to updating forward looking statements or information contained in the annual report. This annual report contains information on the markets, market shares and competitive position of the AREVA group. Unless otherwise indicated, all historical data and forward looking information are based on Group estimates (source: AREVA) and are provided as examples only. To AREVA knowledge, no report is available on the AREVA group markets that is sufficiently complete or objective to serve as a sole reference source. The AREVA group developed estimates based on several sources, including in-house studies and reports, statistics provided by international organizations and professional associations, data published by competitors and information collected by AREVA subsidiaries. The main sources, studies and reports used include (i) the International Atomic Energy Agency (IAEA), the International Energy Agency (IEA), the World Nuclear Association (WNA), the Nuclear Energy Institute (NEA), Nuclear Assurance Corporation (NAC), the European Atomic Energy Community (Euratom) and the Commissariat a l'Energie Atomique (CEA) for the nuclear business; and (ii

  18. Annual Energy Review 1999

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2000-07-01

    A generation ago the Ford Foundation convened a group of experts to explore and assess the Nation’s energy future, and published their conclusions in A Time To Choose: America’s Energy Future (Cambridge, MA: Ballinger, 1974). The Energy Policy Project developed scenarios of U.S. potential energy use in 1985 and 2000. Now, with 1985 well behind us and 2000 nearly on the record books, it may be of interest to take a look back to see what actually happened and consider what it means for our future. The study group sketched three primary scenarios with differing assumptions about the growth of energy use. The Historical Growth scenario assumed that U.S. energy consumption would continue to expand by 3.4 percent per year, the average rate from 1950 to 1970. This scenario assumed no intentional efforts to change the pattern of consumption, only efforts to encourage development of our energy supply. The Technical Fix scenario anticipated a “conscious national effort to use energy more efficiently through engineering know-how." The Zero Energy Growth scenario, while not clamping down on the economy or calling for austerity, incorporated the Technical Fix efficiencies plus additional efficiencies. This third path anticipated that economic growth would depend less on energy-intensive industries and more on those that require less energy, i.e., the service sector. In 2000, total energy consumption was projected to be 187 quadrillion British thermal units (Btu) in the Historical Growth case, 124 quadrillion Btu in the Technical Fix case, and 100 quadrillion Btu in the Zero Energy Growth case. The Annual Energy Review 1999 reports a preliminary total consumption for 1999 of 97 quadrillion Btu (see Table 1.1), and the Energy Information Administration’s Short-Term Energy Outlook (April 2000) forecasts total energy consumption of 98 quadrillion Btu in 2000. What energy consumption path did the United States actually travel to get from 1974, when the scenarios were drawn

  19. Annual energy review 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    This 13th edition presents the Energy Information Administration`s historical energy statistics. For most series, statistics are given for every year from 1949 through 1994; thus, this report is well-suited to long-term trend analyses. It covers all major energy activities, including consumption, production, trade, stocks, and prices for all major energy commodities, including fossil fuels and electricity. Statistics on renewable energy sources are also included: this year, for the first time, usage of renewables by other consumers as well as by electric utilities is included. Also new is a two-part, comprehensive presentation of data on petroleum products supplied by sector for 1949 through 1994. Data from electric utilities and nonutilities are integrated as ``electric power industry`` data; nonutility power gross generation are presented for the first time. One section presents international statistics (for more detail see EIA`s International Energy Annual).

  20. Coal industry annual 1993

    Energy Technology Data Exchange (ETDEWEB)

    1994-12-06

    Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993.

  1. Uranium Industry Annual, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-28

    The Uranium Industry Annual provides current statistical data on the US uranium industry for the Congress, Federal and State agencies, the uranium and electric utility industries, and the public. The feature article, ``Decommissioning of US Conventional Uranium Production Centers,`` is included. Data on uranium raw materials activities including exploration activities and expenditures, resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities including domestic uranium purchases, commitments by utilities, procurement arrangements, uranium imports under purchase contracts and exports, deliveries to enrichment suppliers, inventories, secondary market activities, utility market requirements, and uranium for sale by domestic suppliers are presented in Chapter 2.

  2. Nagra annual report 2007

    Energy Technology Data Exchange (ETDEWEB)

    Ammann, M. (ed.)

    2008-07-01

    This annual report issued by the Swiss National Cooperative for the Disposal of Radioactive Waste reviews the co-operative's activities in the year 2007 and presents an overview of developments in energy policy, planning procedures and funding plans. The selection of sites for the disposal of radioactive wastes in Switzerland is discussed. Various technical questions are briefly addressed and work being carried out in the rock laboratories in the Swiss Alps and Jura mountains is discussed. International co-operation is reviewed and public relations issues are discussed. Finally, organisational structures are described and the financial details for the year 2007 are presented. The report is completed with an appendix containing the co-operative's organigram, waste inventories and listings of publications, addresses and a short glossary.

  3. Nagra annual report 2008

    Energy Technology Data Exchange (ETDEWEB)

    Ammann, M. (ed.)

    2009-07-01

    This annual report issued by the Swiss National Co-operative for the Disposal of Radioactive Waste, Nagra, reviews the co-operative's activities in the year 2008 and presents an overview of developments in energy policy, planning procedures and funding plans. Energy policy and the selection of sites for the disposal of radioactive wastes in Switzerland are discussed. Various technical questions are briefly addressed and work being carried out in the rock laboratories in the Swiss Alps and Jura mountains is discussed. International co-operation is reviewed and public relations issues are discussed. Finally, organisational structures are described and Nagra's financial details for the year 2008 are presented and discussed. The report is completed with an appendix containing the co-operative's organigram, waste inventories and listings of publications, addresses and a short glossary.

  4. Uranium industry annual 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-04-01

    The Uranium Industry Annual 1996 (UIA 1996) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing. The UIA 1996 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. Data on uranium raw materials activities for 1987 through 1996 including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2006, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, uranium imports and exports, and uranium inventories are shown in Chapter 2. A feature article, The Role of Thorium in Nuclear Energy, is included. 24 figs., 56 tabs.

  5. DANSYNC. Annual report 1996

    Energy Technology Data Exchange (ETDEWEB)

    Als-Nielsen, J.

    1997-02-01

    DANSYNC is an organisation of Danish users of hard X-ray synchrotron facilities, funded by The Danish Natural Science Research Council. It was founded in the beginning of 1996, and this is the first Annual Report from DANSYNC. Users span from basic physics at Risoe National Laboratory, Oersted Laboratory and Denmarks Technical University over materials science from Risoe National Laboratory to chemistry and biology at Aarhus University, Copenhagen University and Denmarks Technical University, as well as industrial research represented by Haldor Topsoee A/S and space research at Danish Space Research Institute. We do not have an X-ray synchrotron facility in Denmark, so all of this work is carried out at facilities abroad. Clearly the facility at DESY in Hamburg (HASYLAB and EMBL) is of the greatest significance for Danish synchrotron research. Home page: http://www.dansync.dk/dansync/. (LN).

  6. 1994 MCAP annual report

    Energy Technology Data Exchange (ETDEWEB)

    Harmony, S.C.; Boyack, B.E.

    1995-04-01

    VELCOR is an integrated, engineering-level computer code that models the progression of severe accidents in light water reactor (LWR) nuclear power plants. The entire spectrum of severe accident phenomena, including reactor coolant system and containment thermal-hydraulic response, core heatup, degradation and relocation, and fission product release and transport is treated in MELCOR in a unified framework for both boiling water reactors (BWRs) and pressurized water reactors (PWRs). Its current uses include the estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. Independent assessment efforts have been successfully completed by the US and international MELCOR user communities. Most of these independent assessment efforts have been conducted to support the needs and fulfill the requirements of the individual user organizations. The resources required to perform an extensive set of model and integral code assessments are large. A prudent approach to fostering code development and maturation is to coordinate the individual assessment efforts of the MELCOR user community. While retaining individual control over assessment resources, each organization using the MELCOR code could work with the other users to broaden assessment coverage and minimize duplication. In recognition of these considerations, the US Nuclear Regulatory Commission (US NRC) has initiated the MELCOR Cooperative Assessment Program (MCAP), a vehicle for coordinating and standardizing the assessment practices of the various MELCOR users. In addition, the user community will have a forum to better communicate lessons learned regarding MELCOR applications, capabilities, and user guidelines and limitations and to provide a user community perspective on code development needs and priorities. This second Annual Report builds on the foundation laid with the first Annual Report.

  7. Medicare Update: Annual Wellness Visit

    Science.gov (United States)

    factsheet FEBRUARY 2012 Medicare Update: Annual Wellness Visit ® alz.org Under the Affordable Care Act (the health care reform law), Medicare will now pay for ... Included in the annual wellness visit: • Review and update medical and family history • Review and update a ...

  8. Research on silicon-carbon alloys and interfaces. Final subcontract report, 15 February 1991--31 July 1994

    Energy Technology Data Exchange (ETDEWEB)

    Abelson, J.R. [Illinois Univ., Urbana, IL (United States)

    1995-07-01

    This report describes work performed to develop improved p-type wide-band-gap hydrogenated amorphous silicon-carbon alloy (a-Si{sub 1-x}C{sub x:}H) thin films and interfaces for the ``top junction`` in hydrogenated amorphous silicon (a-Si:H)-based p-i-n solar cells. We used direct current reactive magnetron sputtering to deposit undoped a-Si{sub 1-x}C{sub x}H films with a Tauc band gap E{sub g} of 1.90 eV, a sub-band-gap absorption of 0.4 (at 1.2 eV), an Urbach energy of 55 MeV, an ambipolar diffusion length of 100 nm, an air-mass-one photoconductivity of 10{sup {minus}6}/{Omega}-cm, and a dark conductivity of 8{times} 1O{sup {minus}11}/{Omega}-cm. p{sup +}a-Si{sub 1-x}C{sub x}:H films with a Tauc band gap of 1.85 eV have a dark conductivity of 8 {times} 10{sup {minus}6}/{Omega}-cm and thermal activation energy of 0.28 eV. We used in-situ spectroscopic ellipsometry and post-growth X-ray photoelectron spectroscopy to determine the relative roles of H and Si in the chemical reduction of SnO{sub 2} in the early stages of film growth. We used in-situ spectroscopic ellipsometry to show that a-Si:H can be transformed into {mu}c-Si:H in a subsurface region under appropriate growth conditions. We also determined substrate cleaning and ion bombardment conditions which improve the adhesion of a-Si{sub 1-x}C{sub x}:H films.

  9. Annual Report: Fuel Cells (30 September 2012)

    Energy Technology Data Exchange (ETDEWEB)

    Gerdes, Kirk [NETL; Richards, George [NETL

    2012-09-30

    The comprehensive research plan for FY12 focuses on Solid State Energy Conversion Alliance (SECA) programmatic targets and includes objectives in three primary focus areas: (1) investigation of degradation modes exhibited by the anode/electrolyte/cathode (AEC), development of computational models describing the associated degradation rates, and generation of a modeling tool predicting long-term AEC degradation response, (2) generation of novel cathode materials and microstructures, and implementation of the improved cathode technology to enhance performance, and (3) completion of a proof of concept molten catalytic gasification study.

  10. 2014 HPC Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Jennings, Barbara [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-10-01

    Our commitment is to support you through delivery of an IT environment that provides mission value by transforming the way you use, protect, and access information. We approach this through technical innovation, risk management, and relationships with our workforce, Laboratories leadership, and policy makers nationwide. This second edition of our HPC Annual Report continues our commitment to communicate the details and impact of Sandia’s large-scale computing resources that support the programs associated with our diverse mission areas. A key tenet to our approach is to work with our mission partners to understand and anticipate their requirements and formulate an investment strategy that is aligned with those Laboratories priorities. In doing this, our investments include not only expanding the resources available for scientific computing and modeling and simulation, but also acquiring large-scale systems for data analytics, cloud computing, and Emulytics. We are also investigating new computer architectures in our advanced systems test bed to guide future platform designs and prepare for changes in our code development models. Our initial investments in large-scale institutional platforms that are optimized for Informatics and Emulytics work are serving a diverse customer base. We anticipate continued growth and expansion of these resources in the coming years as the use of these analytic techniques expands across our mission space. If your program could benefit from an investment in innovative systems, please work through your Program Management Unit ’s Mission Computing Council representatives to engage our teams.

  11. ANNUAL INTERVIEWS (MAPS)

    CERN Multimedia

    Human Resources Division

    2002-01-01

    The calendar for the 2002/2003 annual interview programme is confirmed as normally from 15 November 2002 to 15 February 2002 as foreseen in Administrative Circular N° 26 (rev. 2). However, where it is preferred to be as close as possible to 12 months since the last interview, supervisors and staff concerned may agree to the interview taking place up to 15 March 2003. This may also be necessary due to the roles of different supervisors resulting from the particular situations of divisional re-restructurings and detachments this year. The report form template is as last year available on the HR Division Website. A banner on the internal homepage leads directly to the page with the form. In collaboration with AS Division, the MAPS form including the personal data for the first page can be generated via the Human Resources Toolkit (HRT) application. For this exercise each staff member can now generate his/her own MAPS form. Information about how to do this is available here. Human Resources Division Tel. ...

  12. 2007 LDRD ANNUAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    French, T

    2008-12-16

    I am pleased to present the fiscal year 2007 Laboratory Directed Research and Development (LDRD) annual report. This represents the first year that SRNL has been eligible for LDRD participation and our results to date demonstrate we are off to an excellent start. SRNL became a National Laboratory in 2004, and was designated the 'Corporate Laboratory' for the DOE Office of Environmental Management (EM) in 2006. As you will see, we have made great progress since these designations. The LDRD program is one of the tools SRNL is using to enable achievement of our strategic goals for the DOE. The LDRD program allows the laboratory to blend a strong basic science component into our applied technical portfolio. This blending of science with applied technology provides opportunities for our scientists to strengthen our capabilities and delivery. The LDRD program is vital to help SRNL attract and retain leading scientists and engineers who will help build SRNL's future and achieve DOE mission objectives. This program has stimulated our research staff creativity, while realizing benefits from their participation. This investment will yield long term dividends to the DOE in its Environmental Management, Energy, and National Security missions.

  13. Annual conference SAEE 2008

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    Technical and economic challenges of a 1 t CO{sub 2} society was the topic addressed by the 2008 annual conference of the Swiss Association for Energy Economics. One tonne of carbon dioxide per head and year as a long-term energy strategy is the theme of a presentation made by professor Konstantin Boulouchos from the Swiss Federal Institute of Technology ETH in Zurich, Switzerland. Professor Dr. Rainhard Madlener from the Institute for Future Energy Consumer Needs and Behaviour in Aachen, Germany, took a look at the one-ton CO{sub 2} vision as a focus for technical development. Professor Thomas F. Rutherford from the ETH presented an economic analysis of one-ton CO{sub 2} scenarios. Eduard Schumacher, former Chairman of the Board at the IWB utility in Basel, Switzerland, presented examples of how energy policy can be implemented, using the IWB's activities as an example. Hansruedi Kunz, Head of the Energy Department in the Building Department of the Canton of Zurich discussed the chances offered and the problems posed by the implementation of measures that are to lead to the meeting of energy visions for the year 2050. A podium and discussion session completed the conference

  14. Annual Energy Review 2000

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2001-08-01

    The Annual Energy Review (AER) presents the Energy Information Administration’s historical energy statistics. For many series, statistics are given for every year from 1949 through 2000. The statistics, expressed in either physical units or British thermal units, cover all major energy activities, including consumption, production, trade, stocks, and prices, for all major energy commodities, including fossil fuels, electricity, and renewable energy sources. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the Energy Information Administration under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the AER and in other EIA publications.

  15. Annual Energy Review 2002

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    2003-10-01

    The Annual Energy Review (AER) presents the Energy Information Administration’s historical energy statistics. For many series, statistics are given for every year from 1949 through 2002. The statistics, expressed in either physical units or British thermal units, cover all major energy activities, including consumption, production, trade, stocks, and prices, for all major energy commodities, including fossil fuels, electricity, and renewable energy sources. Publication of this report is required under Public Law 95–91 (Department of Energy Organization Act), Section 205(c), and is in keeping with responsibilities given to the Energy Information Administration (EIA) under Section 205(a)(2), which states: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the AER and in other EIA publications. Related Publication: Readers of the AER may also be interested in EIA’s Monthly Energy Review, which presents monthly updates of many of the data in the AER. Contact our National Energy Information Center for more information.

  16. Annual Energy Review 1997

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherine E. [USDOE Energy Information Administration (EIA), Washington, DC (United States)

    1998-07-01

    The Annual Energy Review (AER) presents the Energy Information Administration’s historical energy statistics. For many series, statistics are given for every year from 1949 through 1997. The statistics, expressed in either physical units or British thermal units, cover all major energy activities, including consumption, production, trade, stocks, and prices, for all major energy commodities, including fossil fuels, electricity, and renewable energy sources. Publication of this report is in keeping with responsibilities given to the Energy Information Administration (EIA) in Public Law 95–91 (Department of Energy Organization Act), which states, in part, in Section 205(a)(2) that: “The Administrator shall be responsible for carrying out a central, comprehensive, and unified energy data and information program which will collect, evaluate, assemble, analyze, and disseminate data and information....” The AER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the AER and in other EIA publications.

  17. SKB Annual Report 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    This is the annual report of the Swedish Nuclear Fuel and Waste Management Co (SKB). Part 1 of the report contains an overview of the SKB activities in different fields, and part 2 gives a description of the research and development work on nuclear waste disposal performed during 1996. Lectures and publications as well as reports issued during 1996 are listed in part 3, and summaries of the reports are listed in part 4. The task of SKB is to transport, store and dispose of the spent nuclear fuel and radioactive wastes from the nuclear power plants and to perform the research and development and other measures necessary for this work. SKB is the owner of CLAB, the Central Interim Storage Facility for spent fuel, located at Oskarshamn. CLAB was taken into operation in July 1985 and by the end of 1996 about 2500 tons of spent fuel have been received. At Forsmark the Final Repository for Radioactive Operational Waste (SFR) was taken into operation in April 1988. The repository is situated in crystalline rock under the Baltic Sea. SFR has currently a capacity of about 60000 m{sup 3} or waste. At the end of 1996 at total of 21000 m{sup 3} of waste has been deposited. Transportation from the reactor sites to CLAB and SFR is made by a specially designed ship, M/S Sigyn. The total cost for R,D and D during 1996 amounted to 124 MSEK (about 15 MUSD).

  18. NAGRA annual report 2012

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-07-01

    This report issued by the Swiss National Co-operative for the Disposal of Radioactive Waste NAGRA reviews the co-operative’s activities in the year 2012. In January 2012, the Swiss Federal Office of Energy (SFOE) announced the 20 proposals made by NAGRA for siting areas for nuclear waste repository surface facilities. The discussions within the framework of regional participation focused on the location and layout of the surface facility within the defined planning perimeter. Progress in NAGRA’s work on the safety-based comparison and further narrowing-down of the geological siting regions for the repositories is reported on. NAGRA’s mandate includes its responsibility for preparing the technical and scientific basis for the safe, long-term management of nuclear waste. Progress on the so-called ‘Sectorial Plan’ which addresses the fundamental question of how to safely dispose of all types of radioactive waste is reported on, as is the process of defining locations in Switzerland for one or more deep repositories for nuclear wastes. Public participation in the process is reported on and geochemical considerations involved in designing the repositories are looked at. The work done in the rock laboratories is summarised and international co-operation is noted. The NAGRA ‘Time Ride’ exhibition is also briefly looked at. The report is completed with listings of those involved in NAGRA’s Board of Directors, commissions and auditors along with the annual financial statement for 2012.

  19. Annual report 1997

    Energy Technology Data Exchange (ETDEWEB)

    Chmielewska, D.; Infeld, E.; Zupranski, P. [eds.

    1998-12-31

    In the presented ``Annual Report 1997`` the scientific, organizational end educational activities of the Andrzej Soltan Institute for Nuclear Studies (SINS) are presented. The document is divided into two parts. First of them consist of the general information about management, scientific council, department of SINS, scientific staff, visiting scientists, list of research project (grants), PhD and DSc theses as well as the information about organized schools and exhibitions. The second one: ``Reports on Research`` describes the research activities of SINS. It is divided into 12 parts - in which the works of SINS departments and establishments are presented (Department of Nuclear Reactions, Department of Nuclear Spectroscopy and Technique, Department of Nuclear Electronics, Department of Radiation Shielding and Dosimetry, Department of Plasma Physics and Technology, Department of High Energy Physics, Department of Cosmic Radiation Physics, Department of Atomic Nucleus Theory, Department of Radiation Detectors, Department of Accelerator Physics and Technology, Department of Training an Consulting and Establishment for Nuclear Equipment). Each of these parts are foreworded by short overview given by the head of appropriate department. The foreword, in which the whole activities of the SINS are summarized, given by head of the Institute professor Z. Sujkowski is also given

  20. Annual Report 1998

    Energy Technology Data Exchange (ETDEWEB)

    Chmielewska, D.; Infeld, E.; Preibisz, Z.; Zupranski, P. [eds.

    1999-10-01

    In the presented ``Annual Report 1998`` the scientific, organizational and educational activities of the Andrzej Soltan Institute for Nuclear Studies (SINS) are presented. The document is divided into two parts. First of them consists of the general information about management, scientific council, department of SINS, scientific staff, visiting scientists, list of research project (grants), PhD and DSc theses as well as the information about organized schools and exhibitions. The second one: ``Reports on Research`` describes the research activities of SINS. It is divided into 12 parts - in which the works of SINS departments and establishments are presented (Department of Nuclear Reactions, Department of Nuclear Spectroscopy and Technique, Department of Nuclear Electronics, Department of Radiation Shielding and Dosimetry, Department of Plasma Physics and Technology, Department of High Energy Physics, Department of Cosmic Radiation Physics, Department of Nuclear Theory, Department of Radiation Detectors, Department of Accelerator Physics and Technology, Department of Training an Consulting and Establishment for Nuclear Equipment). Each of these parts are preceded by a short overview given by the head of the given department. The foreword, in which the whole activities of the SINS are summarized, given by head of the Institute professor Z. Sujkowski is also given

  1. Calendar year 2002 annual site environmental report for Tonopah Test Range, Nevada and Kauai Test Facility, Hawaii.

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Katrina; Sanchez, Rebecca V.; Mayeux, Lucie; Koss, Susan I.; Salinas, Stephanie A.

    2003-09-01

    Tonopah Test Range (TTR) in Nevada and Kauai Test Facility (KTF) in Hawaii are government-owned, contractor-operated facilities operated by Sandia Corporation, a subsidiary of Lockheed Martin Corporation. The U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA), through the Sandia Site Office (SSO), in Albuquerque, NM, oversees TTR and KTF's operations. Sandia Corporation conducts operations at TTR in support of DOE/NNSA's Weapons Ordnance Program and has operated the site since 1957. Westinghouse Government Services subcontracts to Sandia Corporation in administering most of the environmental programs at TTR. Sandia Corporation operates KTF as a rocket preparation launching and tracking facility. This Annual Site Environmental Report (ASER) summarizes data and the compliance status of the environmental protection and monitoring program at TTR and KTF through Calendar Year (CY) 2002. The compliance status of environmental regulations applicable at these sites include state and federal regulations governing air emissions, wastewater effluent, waste management, terrestrial surveillance, and Environmental Restoration (ER) cleanup activities. Sandia Corporation is responsible only for those environmental program activities related to its operations. The DOE/NNSA, Nevada Site Office (NSO) retains responsibility for the cleanup and management of ER TTR sites. Currently, there are no ER Sites at KTF. Environmental monitoring and surveillance programs are required by DOE Order 5400.1, General Environmental Protection Program (DOE 1990) and DOE Order 231.1, Environment, Safety, and Health Reporting (DOE 1996).

  2. Calendar year 2003 : annual site enviromental report for Tonopah Test Range, Nevada and Kauai Test Facility, Hawaii.

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Katrina; Sanchez, Rebecca V.; Mayeux, Lucie; Koss, Susan I.; Salinas, Stephanie A.

    2004-09-01

    Tonopah Test Range (TTR) in Nevada and Kauai Test Facility (KTF) in Hawaii are government-owned, contractor-operated facilities operated by Sandia Corporation, a subsidiary of Lockheed Martin Corporation. The U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA), through the Sandia Site Office (SSO), in Albuquerque, NM, manages TTR and KTF's operations. Sandia Corporation conducts operations at TTR in support of DOE/NNSA's Weapons Ordnance Program and has operated the site since 1957. Westinghouse Government Services subcontracts to Sandia Corporation in administering most of the environmental programs at TTR. Sandia Corporation operates KTF as a rocket preparation launching and tracking facility. This Annual Site Environmental Report (ASER) summarizes data and the compliance status of the environmental protection and monitoring program at TTR and KTF through Calendar Year (CY) 2003. The compliance status of environmental regulations applicable at these sites include state and federal regulations governing air emissions, wastewater effluent, waste management, terrestrial surveillance, and Environmental Restoration (ER) cleanup activities. Sandia Corporation is responsible only for those environmental program activities related to its operations. The DOE/NNSA, Nevada Site Office (NSO) retains responsibility for the cleanup and management of ER TTR sites. Currently, there are no ER Sites at KTF. Environmental monitoring and surveillance programs are required by DOE Order 450.1, Environmental Protection Program (DOE 2003) and DOE Order 231.1 Chg 2., Environment, Safety, and Health Reporting (DOE 1996).

  3. Calendar year 2007 annual site environmental report for Tonopah Test Range, Nevada and Kauai Test Facility, Hawaii,

    Energy Technology Data Exchange (ETDEWEB)

    Agogino, Karen [Department of Energy, Albuquerque, NM (United States). National Nuclear Security Administration (NNSA); Sanchez, Rebecca [Sandia Corp., Albuquerque, NM (United States)

    2008-09-30

    Tonopah Test Range (TTR) in Nevada and Kauai Test Facility (KTF) in Hawaii are government-owned, contractor-operated facilities operated by Sandia Corporation (Sandia), a wholly owned subsidiary of Lockheed Martin Corporation. The U.S. Department of Energy (DOE)/National Nuclear Security Administration (NNSA), through the Sandia Site Offi ce (SSO), in Albuquerque, NM, administers the contract and oversees contractor operations at TTR and KTF. Sandia manages and conducts operations at TTR in support of the DOE/NNSA’s Weapons Ordnance Program and has operated the site since 1957. Washington Group International subcontracts to Sandia in administering most of the environmental programs at TTR. Sandia operates KTF as a rocket preparation launching and tracking facility. This Annual Site Environmental Report (ASER) summarizes data and the compliance status of the environmental protection and monitoring program at TTR and KTF through Calendar Year (CY) 2007. The compliance status of environmental regulations applicable at these sites include state and federal regulations governing air emissions, wastewater effluent, waste management, terrestrial surveillance, and Environmental Restoration (ER) cleanup activities. Sandia is responsible only for those environmental program activities related to its operations. The DOE/NNSA/Nevada Site Offi ce (NSO) retains responsibility for the cleanup and management of ER TTR sites. Currently, there are no ER Sites at KTF. Environmental monitoring and surveillance programs are required by DOE Order 450.1, Environmental Protection Program (DOE 2007a) and DOE Manual 231.1-1A, Environment, Safety, and Health Reporting Manual (DOE 2007).

  4. 2013 Annual Site Environmental Report for Sandia National Laboratories Tonopah Test Range Nevada & Kauai Test Facility Hawaii

    Energy Technology Data Exchange (ETDEWEB)

    Griffith, Stacy Rene [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Agogino, Karen [National Nuclear Security Administration (NNSA), Washington, DC (United States); Li, Jun [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); White, Nancy [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Minitrez, Alexandra [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Avery, Penny [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Bailey-White, Brenda [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Bonaguidi, Joseph [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Catechis, Christopher [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); duMond, Michael [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Eckstein, Joanna [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Evelo, Stacie [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Forston, William [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Herring, III, Allen [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Lantow, Tiffany [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Martinez, Reuben [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Mauser, Joseph [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Miller, Amy [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Miller, Mark [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Payne, Jennifer [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Peek, Dennis [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Reiser, Anita [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Ricketson, Sherry [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Roma, Charles [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Salinas, Stephanie [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Ullrich, Rebecca [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2014-08-01

    Tonopah Test Range (TTR) in Nevada and Kauai Test Facility (KTF) in Hawaii are government-owned, contractor-operated facilities managed and operated by Sandia Corporation (Sandia), a wholly owned subsidiary of Lockheed Martin Corporation. The U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA), through the Sandia Field Office (SFO), in Albuquerque, New Mexico, administers the contract and oversees contractor operations at TTR and KTF. Sandia manages and conducts operations at TTR in support of the DOE/NNSA’s Weapons Ordnance Program and has operated the site since 1957. Navarro Research and Engineering subcontracts to Sandia in administering most of the environmental programs at TTR. Sandia operates KTF as a rocket preparation launching and tracking facility. This Annual Site Environmental Report summarizes data and the compliance status of the sustainability, environmental protection, and monitoring program at TTR and KTF through Calendar Year 2013. The compliance status of environmental regulations applicable at these sites include state and federal regulations governing air emissions, wastewater effluent, waste management, terrestrial surveillance, Environmental Restoration (ER) cleanup activities, and the National Environmental Policy Act. Sandia is responsible only for those environmental program activities related to its operations. The DOE/NNSA/Nevada Field Office retains responsibility for the cleanup and management of TTR ER sites. Environmental monitoring and surveillance programs are required by DOE Order 231.1B, Environment, Safety, and Health Reporting (DOE 2012).

  5. LLNL NESHAPs 2004 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R; Gallegos, G; Peterson, R; Wilson, K; Harrach, R J; Gallegos, G M; Peterson, S R; Wilson, K R

    2005-06-27

    This annual report is prepared pursuant to the National Emission Standards for Hazardous Air Pollutants (NESHAPs; Title 40 Code of Federal Regulations [CFR] Part 61, Subpart H). Subpart H governs radionuclide emissions to air from Department of Energy (DOE) facilities.

  6. Annual review of computer science

    Energy Technology Data Exchange (ETDEWEB)

    Traub, J.F. (Columbia Univ., New York, NY (USA)); Grosz, B.J. (Harvard Univ., Cambridge, MA (USA)); Lampson, B.W. (Digital Equipment Corp. (US)); Nilsson, N.J. (Stanford Univ., CA (USA))

    1988-01-01

    This book contains the annual review of computer science. Topics covered include: Database security, parallel algorithmic techniques for combinatorial computation, algebraic complexity theory, computer applications in manufacturing, and computational geometry.

  7. Nursing Facility Initiative Annual Report

    Data.gov (United States)

    U.S. Department of Health & Human Services — This annual report summarizes impacts from the Initiative to Reduce Avoidable Hospitalizations among Nursing Facility Residents in 2014. This initiative is designed...

  8. 2005 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Chrzanowski, P; Walter, K

    2006-03-31

    As the cover of our ''2005 Annual Report'' highlights, Lawrence Livermore National Laboratory joined the international science community in celebrating the World Year of Physics in 2005, with special events and science outreach and education programs. Einstein's remarkable discoveries in 1905 provided an opportunity to reflect on how physics has changed the world during the last century and on the promise of future beneficial discoveries. For half of the past century, Lawrence Livermore, which was established to meet an urgent national security need, has been contributing to the advancement of science and technology in a very special way. Co-founder Ernest O. Lawrence was the leading proponent in his generation of large-scale, multidisciplinary science and technology teams. That's Livermore's distinctive heritage and our continuing approach as a national laboratory managed and operated by the University of California for the Department of Energy's National Nuclear Security Administration (DOE/NNSA). We focus on important problems that affect our nation's security and seek breakthrough advances in science and technology to achieve mission goals. An event in 2005 exemplifies our focus on science and technology advances in support of mission goals. In October, distinguished visitors came to Livermore to celebrate the tenth anniversary of the Accelerated Strategic Computing Initiative (now called the Advanced Simulation and Computing Program, or ASC). ASC was launched in 1995 by DOE/NNSA to achieve a million-fold increase in computing power in a decade. The goal was motivated by the need to simulate the three-dimensional performance of a nuclear weapon in sufficient resolution and with the appropriately detailed physics models included. This mission-driven goal is a key part of fulfilling Livermore's foremost responsibility to ensure that the nuclear weapons in the nation's smaller 21st-century stockpile remain

  9. Annual energy review 2003

    Energy Technology Data Exchange (ETDEWEB)

    Seiferlein, Katherin E. [Energy Information Adminstration (EIA), Washington, DC (United States)

    2004-09-30

    The Annual Energy Review 2003 is a statistical history of energy activities in the United States in modern times. Data are presented for all major forms of energy by production (extraction of energy from the earth, water, and other parts of the environment), consumption by end-user sector, trade with other nations, storage changes, and pricing. Much of the data provided covers the fossil fuels—coal, petroleum, and natural gas. Fossil fuels are nature’s batteries; they have stored the sun’s energy over millennia past. It is primarily that captured energy that we are drawing on today to fuel the activities of the modern economy. Data in this report measure the extraordinary expansion of our use of fossil fuels from 29 quadrillion British thermal units (Btu) in 1949 to 84 quadrillion Btu in 2003. In recent years, fossil fuels accounted for 86 percent of all energy consumed in the United States. This report also records the development of an entirely new energy industry—the nuclear electric power industry. The industry got its start in this country in 1957 when the Shippingport, Pennsylvania, nuclear electric power plant came on line. Since that time, the industry has grown to account for 20 percent of our electrical output and 8 percent of all energy used in the country. Renewable energy is a third major category of energy reported in this volume. Unlike fossil fuels, which are finite in supply, renewable energy is essentially inexhaustible because it can be replenished. Types of energy covered in the renewable category include conventional hydroelectric power, which is power derived from falling water; wood; waste; alcohol fuels; geothermal; solar; and wind. Together, these forms of energy accounted for about 6 percent of all U.S. energy consumption in recent years.

  10. Annual energy review 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The Annual Energy Review (AER) is a historical data report that tells many stories. It describes, in numbers, the changes that have occurred in US energy markets since the midpoint of the 20th century. In many cases, those markets differ vastly from those of a half-century ago. By studying the graphs and data tables presented in this report, readers can learn about past energy supply and usage in the United States and gain an understanding of the issues in energy and the environment now before use. While most of this year`s report content is similar to last year`s, there are some noteworthy developments. Table 1.1 has been restructured into more summarized groupings -- fossil fuels, nuclear electric power, and renewable energy -- to aid analysts in their examination of the basic trends in those broad categories. Readers` attention is also directed to the electricity section, where considerable reformatting of the tables and graphs has been carried out to help clarify past and recent trends in the electric power industry as it enters a period of radical restructuring. Table 9.1, which summarizes US nuclear generating units, has been redeveloped to cover the entire history of the industry in this country and to provide categories relevant in assessing the future of the industry, such as the numbers of ordered generating units that have been canceled and those that were built and later shut down. In general, the AER emphasizes domestic energy statistics. Sections 1 through 10 and Section 12 are devoted mostly to US data; Section 11 reports on international statistics and world totals. 140 figs., 141 tabs.

  11. Annual Report, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Buettner, Herma G.; Leadbetter, Alan J. [eds.] [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)

    1999-11-01

    In this Annual Report a selection of about 30 scientific achievements are highlighted. These are intended to represent the huge range of high quality research carried out at ILL. In 1998 about 750 experiments were performed in the 225 days of reactor operation. The fields of magnetism and strongly correlated electron systems continue to be fertile and to throw up strong new growth. Remarkable new advances are coming from the applications of both existing and new neutron techniques and the development of new materials. These highlights concern superconductors, nano-magnetic particles, colossal magneto-resistance, magnetic-nuclear correlations, quantum spin systems and more. Novel magnetic measurements are also reported for a quasicrystal and on thin films of both normal and superconducting materials. Thanks to special abilities of neutrons to penetrate matter new results were obtained: following the production of novel intermetallic compounds, pressure dependence of phonon frequencies, the structure of glasses, solutions (in both bulk and thin films) and adsorbed phases; dynamics and relaxation in liquids; the confirmation of reptant motion in linear polymers, self-assembly and shear phenomena in liquid crystals. Three important results from nuclear physics are also included. These involve: fission-produced neutron-rich nuclei, weighing gamma photons in connection with the determination of fundamental constants and the determination of interatomic potentials from the slowing down process of atoms recoiling from gamma-ray emission - a direct link between nuclear and solid-state physics. The neutron experiments of importance for particle physics and biology will be reported next year

  12. 口虾蛄繁殖周期及生殖细胞发育的研究%Annual reproductive cycle and germ cell development in mantis shrimp Oratosquilla oratoria

    Institute of Scientific and Technical Information of China (English)

    刘海映; 谷德贤; 姜玉声; 邢坤

    2013-01-01

    The ovary annual changes in gonado-somatic index (GSI) and germ cell development were observed monthly and histologically in mantis shrimp Oratosquilla oratoria in coastal Dalian.The results showed that the mantis shrimp had gradual mature gonads after March when the water became warming,higher GSI and the maximal GSI on June,afterwards lower GSI due to spawning on July,and the minimal GSI on September.The 1 year old mantis shrimp showed maturity,and spawned once a year.The spermatogenesis was divided into five stages including spermatogonia stage,primary spermatocyte stage,secondary spermatocyte stage,spermatid stage,and sperm stage.The oogenesis can be divided into four stages,the oogonium stage,primary oocyte stage,growth stage,and mature oocyte stage.%对大连市黑石礁海域口虾蛄Oratosquilla oratoria卵巢性腺指数的周年变化进行测定,对雌雄个体的生殖细胞发育进行了组织学观察.结果表明:3月,随着水温的升高,口虾蛄繁殖个体卵巢发育逐渐成熟,性腺指数上升,至6月达到最大值,7月,随着繁殖个体的排卵,性腺指数下降,至9月出现全年的最小值;口虾蛄1龄即可性成熟,每年产卵1次;雄性生殖细胞发育分为精原细胞期、初级精母细胞期、次级精母细胞期、精细胞期和精子期5个时期,雌性生殖细胞发育分为卵原细胞期、卵黄形成前期、卵黄形成期和成熟期4个时期.

  13. 15 CFR 296.33 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Annual report. 296.33 Section 296.33... Dissemination of Program Results § 296.33 Annual report. The Director shall submit annually to the Committee on... an evaluation of ongoing and completed awards. The first annual report shall include best...

  14. 25 CFR 122.9 - Annual report.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Annual report. 122.9 Section 122.9 Indians BUREAU OF... EDUCATION § 122.9 Annual report. The Osage Tribal Education Committee shall submit an annual report on OMB approved Form 1076-0106, Higher Education Annual Report, to the Assistant Secretary or his/her...

  15. 49 CFR 195.49 - Annual report.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Annual report. 195.49 Section 195.49... PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.49 Annual report. Beginning no... dioxide pipelines. Operators are encouraged, but not required, to file an annual report by June 15,...

  16. 16 CFR 1018.42 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Annual report. 1018.42 Section 1018.42... Reports and Audits § 1018.42 Annual report. (a) The Advisory Committee Management Officer shall prepare an annual report on the Commission's advisory committees for inclusion in the President's annual report...

  17. Stockholder Reactions to Corporate Annual Reports.

    Science.gov (United States)

    Means, Thomas Lee

    A study was conducted to assess the extent to which (1) stockholders consider corporate annual reports to be informative and useful, (2) they actually read annual reports, (3) they consider annual reports to be impressive, and (4) they are motivated by the annual report to invest further in corporations in which they already own stock. After the…

  18. 77 FR 64463 - Annual Retail Trade Survey

    Science.gov (United States)

    2012-10-22

    ..., the Census Bureau will collect data covering annual sales, annual e- commerce sales, year-end..., accounts receivables, and, for selected industries, merchandise line sales, and percent of e-commerce sales..., annual sales, annual e-commerce sales, purchases, total and detailed operating expenses,...

  19. 75 FR 63804 - Annual Retail Trade Survey

    Science.gov (United States)

    2010-10-18

    ... survey, the Census Bureau will collect data covering annual sales, annual e-commerce sales, year-end... percent of e-commerce sales to customers located outside the United States. These data are collected to... classification basis, annual sales, annual e-commerce sales, purchases, total operating expenses,...

  20. 2014 Annual Conference on Experimental and Applied Mechanics

    CERN Document Server

    Korach, Chad; Zavattieri, Pablo; Prorok, Barton; Grande-Allen, K; Carroll, Jay; Daly, Samantha; Qi, H; Antoun, Bonnie; Hall, Richard; Lu, Hongbing; Arzoumanidis, Alex; Silberstein, Meredith; Furmanski, Jevan; Amirkhizi, Alireza; Gonzalez-Gutierrez, Joamin; Jin, Helena; Sciammarella, Cesar; Yoshida, Sanichiro; Lamberti, Luciano; Sottos, Nancy; Rowlands, Robert; Dannemann, Kathryn; Tandon, Gyaneshwar; Song, Bo; Casem, Daniel; Kimberley, Jamie; Starman, LaVern; Hay, Jennifer; Shaw, Gordon

    2015-01-01

    Proceedings of the 2014 Annual Conference on Experimental and Applied Mechanics, the seventh volume of eight from the Conference, brings together contributions to this important area of research and engineering.  The collection presents early findings and case studies on a wide range of areas, including: Soft Tissues Mechanics Natural Materials & Bio-Inspiration Tissue Engineering Cells Mechanics

  1. NERI 2004 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2004-01-01

    The United States Department of Energy (DOE) created the Nuclear Energy Research Initiative (NERI) in Fiscal Year (FY) 1999 in response to recommendations provided by the President's Committee of Advisors on Science and Technology. The purpose of NERI is to sponsor research and development (R&D) in the nuclear energy sciences to address the principal barriers to the future use of nuclear energy in the United States. NERI is helping to preserve the nuclear science and engineering infrastructure within the Nation's universities, laboratories, and industry, and is advancing the development of nuclear energy technology, enabling the United States to maintain a competitive position in nuclear science and technology. Research under this initiative also addresses issues associated with the maintenance of existing U.S. nuclear plants. The NERI program is managed and funded by DOE's Office of Nuclear Energy, Science and Technology. ''The Nuclear Energy Research Initiative 2004 Annual Report'' serves to inform interested parties of progress made in NERI on a programmatic level as well as research progress made on individual NERI projects. Section 2 of this report provides background on the creation and implementation of NERI and on the focus areas for NERI research. Section 3 provides a discussion on NERI's mission, goals and objectives, and work scope. Section 4 highlights the major accomplishments of the NERI projects and provides brief summaries of the NERI research efforts that were completed in 2004. Section 5 provides a discussion on the impact NERI has had on U.S. university nuclear programs. Sections 6 through 8 provide project status reports by research area for each of the fiscal year (FY) 2001 and 2002 projects that were active in FY 2004. Research objectives, progress made over the last year, and activities planned for the next year are described for each project. Sections 9 through 11 present each of the newly awarded 2005

  2. Annual report 99

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    This volume of the Annual Report for the year 1999 provides the best illustration of this attempt: 30 highlights are presented covering a remarkable range of science and technique. As with last year's report, a wide spectrum of neutron science is embraced from biology, through to studies in chemistry, materials science and magnetism, to particle physics. To maintain this excellence, important efforts have been made in instrumentation; they are described in the technical section together with the Millennium Programme. This report is an appropriate illustration of the unique value of neutron methods for the study of a wide range of materials proving the usefulness of large-scale facilities such as the ILL. In 1999, the reactor operated for 208 days and more than 700 experiments were carried out in over 4400 days of scheduled beam time. Unfortunately, there was a failure of the hot source in December 1999 leading to a loss of about 20 days of beam time. Therefore, in 2000 the reactor will operate without the hot source. However, this will only affect 10 % of ILL's instruments. As in previous years, a large number of high-quality experiments was proposed and performed to tackle a broad range of scientific questions. For example in biology, the results presented here demonstrate that the contrast-variation method combined with small-angle scattering and neutron reflectivity techniques is a remarkable and unique tool for the investigation of biological materials. In the field of soft matter and liquids, it is known that confined geometry substantially modifies the properties of systems as diverse as simple water, polymers and quantum fluids. Neutron scattering experiments, presented here, have revealed the static and dynamic characteristics of these materials under conditions of confinement. In materials sciences, the penetration and contrast properties of neutrons are exploited, particularly in the case of small-angle scattering applied to alloys. Finally, the

  3. Computation Directorate Annual Report 2003

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, D L; McGraw, J R; Ashby, S F; McCoy, M G; Michels, T C; Eltgroth, P G

    2004-03-12

    Big computers are icons: symbols of the culture, and of the larger computing infrastructure that exists at Lawrence Livermore. Through the collective effort of Laboratory personnel, they enable scientific discovery and engineering development on an unprecedented scale. For more than three decades, the Computation Directorate has supplied the big computers that enable the science necessary for Laboratory missions and programs. Livermore supercomputing is uniquely mission driven. The high-fidelity weapon simulation capabilities essential to the Stockpile Stewardship Program compel major advances in weapons codes and science, compute power, and computational infrastructure. Computation's activities align with this vital mission of the Department of Energy. Increasingly, non-weapons Laboratory programs also rely on computer simulation. World-class achievements have been accomplished by LLNL specialists working in multi-disciplinary research and development teams. In these teams, Computation personnel employ a wide array of skills, from desktop support expertise, to complex applications development, to advanced research. Computation's skilled professionals make the Directorate the success that it has become. These individuals know the importance of the work they do and the many ways it contributes to Laboratory missions. They make appropriate and timely decisions that move the entire organization forward. They make Computation a leader in helping LLNL achieve its programmatic milestones. I dedicate this inaugural Annual Report to the people of Computation in recognition of their continuing contributions. I am proud that we perform our work securely and safely. Despite increased cyber attacks on our computing infrastructure from the Internet, advanced cyber security practices ensure that our computing environment remains secure. Through Integrated Safety Management (ISM) and diligent oversight, we address safety issues promptly and aggressively. The safety of

  4. 2008 Annual Report

    Science.gov (United States)

    2008-01-01

    Protein-protein interaction analysis by C-terminally specific fluorescence labeling and fluorescence cross-correlation spectroscopy . Nucleic Acids...metabolic complexes in bacteria that are capable of efficient metabolic conversions via fermentation of renewable resources. We have chosen as a...steric bulk. These protein-based switches will be useful for direct monitoring of intracellular 1,2-PD titers in living cells and are expected to open

  5. Engineering Annual Summary 1998

    Energy Technology Data Exchange (ETDEWEB)

    Dimolitsas, S

    1999-05-01

    Unlike most research and development laboratories, Lawrence Livermore National Laboratory (LLNL) is responsible for delivering production-ready designs. Unlike most industry, LLNL is responsible for R and D that must significantly increase the nation's security. This rare combination of production engineering expertise and national R and D agenda identifies LLNL as one of the few organizations today that conducts cutting-edge engineering on grand-scale problems, while facing enormous technical risk and undergoing diligent scrutiny of its budget, schedule, and performance. On the grand scale, cutting-edge technologies are emerging from our recent ventures into ''Xtreme Engineering{trademark}.'' Basically, we must integrate and extend technologies concurrently and then push them to their extreme, such as building very large structures but aligning them with extreme precision. As we extend these technologies, we push the boundaries of engineering capabilities at both poles: microscale and ultrascale. Today, in the ultrascale realm, we are building NIF, the world's largest laser, which demands one of the world's most complex operating systems with 9000 motors integrated through over 500 computers to control 60,000 points for every laser shot. On the other pole, we have fabricated the world's smallest surgical tools and the smallest instruments for detecting biological and chemical agents used by antiterrorists. Later in this Annual Summary, we highlight some of our recent innovations in the area of Xtreme Engineering, including large-scale computer simulations of massive structures such as major bridges to prepare retrofitting designs to withstand earthquakes. Another feature is our conceptual breakthrough in developing the world's fastest airplane, HyperSoar, which can reach anywhere in the planet in two hours at speeds of 6700 mph. In the last few years, Engineering has significantly pushed the technology in structural

  6. Energy Materials Coordinating Committee (EMaCC), fiscal year 1985. Annual technical report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1986-05-01

    The DOE Energy Materials Coordinating Committee (EMaCC) serves primarily to enhance coordination among the Department's materials programs and to further the effective use of materials expertise within the Department. These functions are accomplished through the exchange of budgetary and planning information among program managers and through technical meeting/workshops on selected topics involving both DOE and major contractors. Four topical subcommittees on Structural Ceramics, Batteries and Fuel Cells, Radioactive Waste Containment, and Steel are established and are continuing their own program. The FY 1985 and FY 1986 meeting program is given. The EMaCC aids in obtaining materials-related inputs for both intra- and inter-agency compilations. Brief summaries of the materials research programs associated with each office and division are presented, including tables listing individual projects and the FY 1985 budgets for each. More details on the individual projects within the divisions and the specific tasks or subcontracts within the various projects are given in the paragraph descriptions.

  7. The 23rd Annual Meeting of the European Tissue Repair Society (ETRS) in Reims, France

    NARCIS (Netherlands)

    Hoff, J.W. Von den; Agren, M.S.; Coulomb, B.; Eming, S.A.; Lataillade, J.J.

    2014-01-01

    The 23rd Annual Meeting of the European Tissue Repair Society, Reims, France, October 23 to 25, 2013 focused on tissue repair and regenerative medicine covering topics such as stem cells, biomaterials, tissue engineering, and burns.

  8. Energy Program annual report

    Energy Technology Data Exchange (ETDEWEB)

    Borg, I.Y. (ed.)

    1988-02-01

    The national economy is particularly dependent on efficient electrical generation and transportation. Electrical demand continues to grow and will increasingly rely on coal and nuclear fuels. The nuclear power industry still has not found a solution to the problem of disposing of the waste produced by nuclear reactors. Although coal is in ample supply and the infrastructure is in place for its utilization, environmental problems and improved conversion processes remain technical challenges. In the case of transportation, the nation depends almost exclusively on liquid fuels with attendant reliance on imported oil. Economic alternates---synfuels from coal, natural gas, and oil shale, or fuel cells and batteries---have yet to be developed or perfected so as to impact the marketplace. Inefficiencies in energy conversion in almost all phases of resource utilization remain. These collective problems are the focus of the Energy Program.

  9. The 23rd Annual Meeting of the European Tissue Repair Society (ETRS) in Reims, France

    DEFF Research Database (Denmark)

    Von den Hoff, Johannes W; Ågren, Sven Per Magnus; Coulomb, Bernard;

    2014-01-01

    The 23rd Annual Meeting of the European Tissue Repair Society, Reims, France, October 23 to 25, 2013 focused on tissue repair and regenerative medicine covering topics such as stem cells, biomaterials, tissue engineering, and burns.......The 23rd Annual Meeting of the European Tissue Repair Society, Reims, France, October 23 to 25, 2013 focused on tissue repair and regenerative medicine covering topics such as stem cells, biomaterials, tissue engineering, and burns....

  10. Annual energy yield of the fluorescent solar concentrator

    Energy Technology Data Exchange (ETDEWEB)

    Van Sark, W.G.J.H.M.; Hellenbrand, G.F.M.G. [Department of Science, Technology and Society, Copernicus Institute for Sustainable Development and Innovation, Utrecht University, Heidelberglaan 2, 3584 CS Utrecht (Netherlands); Bende, E.E.; Burgers, A.R.; Slooff, L.H. [ECN Solar Energy, P.O. Box 1, 1755 ZG Petten (Netherlands)

    2008-09-15

    Fluorescent solar concentrators are but one candidate for lowering the costs of photovoltaic technology. State-of-the-art device conversion efficiencies are around 4%, and the device configuration can be optimized in terms of Euro per Watt. This paper aims to estimate the annual energy yield of such an optimized device configuration, using a detailed minutely spectral irradiance data set, describing a full year in the Netherlands, in combination with a ray-tracing model of the fluorescent solar concentrator. The spectral dataset is modeled using experimentally determined global, direct, and diffuse irradiation data on a minutely basis. Performance variations during the day for a number of typical days are investigated, i.e., for a clear summer day, a cloudy summer day, a clear winter day, and a cloudy winter day, using a ray-trace model of the fluorescent solar concentrator. Also, monthly aggregated spectra are used, as well as an annually aggregated spectrum to determine monthly and annual energy yields, respectively. As a result of a cost-per-unit-of-power optimization study, an optimum size of 23x23x0.1 cm{sup 3} was used, and an annual energy yield of 41.3 kWh/m{sup 2} could be estimated; this is 4.7 times lower than the annual energy yield of a state-of-the-art silicon solar cell.

  11. Study on Global Value Chain Governance,Knowledge Transfer and Subcontracting Business Upgrading:Taking the Pearl River Delta as an Example%全球价值链治理、知识转移与代工企业升级——以珠三角地区为例

    Institute of Scientific and Technical Information of China (English)

    赖磊

    2012-01-01

    代工企业在全球价值链的升级具有战略性和紧迫性,其升级并不是独立自发的,而是受到了全球价值链中各经济主体之间的组织形式和关系安排的统一约束。知识经济的发展也为代工企业的升级创造了新的机遇。全球价值链、知识转移以及代工企业的升级之间存在着密切的关系,文章通过分析全球价值链治理下的全球领先企业与代工企业之间的知识转移模型,从而提出代工企业的升级建议。%The upgrading of subcontracting business in global value chain (GVC) is both strategic and emergent, but is neither independent nor spontaneous, which is restrained by the organizational form and relationship arrangement among economic bodies in GVC. The development of knowledge economy has also created a new opportunity for the upgrading of subcontracting business. The paper analyzes the model of knowledge transfer between the global leading business and the subcontracting business under the GVC governance, and proposes some suggestions for the upgrading of subcontracting business.

  12. The German Photographic Annual; 1972.

    Science.gov (United States)

    Strache, Wolf, Ed.; Steinert, Otto, Ed.

    Designed as a forum for the creative photographer who can produce work of an outstanding character, this 18th edition of the annual presents over 160 photographs whose themes range from advertising and industrial pictures, through unusual pictorial solutions in fashion photography, to experimental work, novel nude studies, and dramatic landscapes.…

  13. Strategic petroleum reserve annual report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-15

    Section 165 of the Energy Policy and Conservation Act (Public Law 94- 163), as amended, requires the Secretary of Energy to submit annual reports to the President and the Congress on activities of the Strategic Petroleum Reserve (SPR). This report describes activities for the year ending December 31, 1995.

  14. 2014 Fordham Sponsorship Annual Report

    Science.gov (United States)

    Thomas B. Fordham Foundation, 2014

    2014-01-01

    The 2014 Fordham Sponsorship Annual Report is our opportunity to share the Fordham Foundation's work as the sponsor of eleven schools serving 3,200 students, and our related policy work in Ohio and nationally. We are fortunate as an organization that our policy work benefits our sponsorship efforts; and, that our lessons from sponsorship inform…

  15. Louisiana Believes: Annual Report 2013

    Science.gov (United States)

    Louisiana Department of Education, 2013

    2013-01-01

    "Louisiana Believes" is the state's comprehensive plan to ensure every student is on track to a professional career or a college degree. This annual report details Louisiana's progress toward that objective during the 2012-2013 school year, along with strategy for the coming school year. "Louisiana Believes" has three…

  16. FY 1994 Annual Work Plan

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    This is the third Office of Inspector General (OIG)Annual Work Plan. Its purpose is to summarize work completed in Fiscal Year (FY) 1993, identify ongoing projects from previous fiscal years which the OIG intends to continue into FY 1994, and announce planned projects which the OIG intends to begin in FY 19994.

  17. Migrant Ministry, 1967. Annual Report.

    Science.gov (United States)

    National Council of Churches of Christ, New York, NY.

    The first annual meeting of the Migrant Ministry Section discussed and evaluated 10 policy and program goals established for the Fifth Decade. The result was the adoption and assignment for implementation of recommendations in 5 Task Force areas concerning migrant labor, education, and training. Significant parts of 35 state reports are presented…

  18. Annual report 1996; Aarsrapport 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    The annual report from the Norwegian Institute for Air Research presents the activities at the institute. The activities cover fields like motor traffic and air quality of urban areas, acid precipitation, the ozone layer, advanced environmental monitoring systems, environmental contamination, and environmental problems in Arctic. 17 figs., 1 tab.

  19. CIEE 1993 annual conference: Program

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-01

    The California Institute for Energy efficiency`s third annual conference highlights the results of CIEE-sponsored multiyear research in three programs: Building Energy Efficiency, Air Quality Impacts of Energy Efficiency, and End-Use Resource Planning. Results from scoping studies, Director`s discretionary research, and exploratory research are also featured.

  20. 1982 laser program annual report

    Energy Technology Data Exchange (ETDEWEB)

    Hendricks, C.D.; Grow, G.R. (eds.)

    1983-08-01

    This annual report covers the following eight sections: (1) laser program review, (2) laser systems and operation, (3) target design, (4) target fabrication, (5) fusion experiments program, (6) Zeus laser project, (7) laser research and development, and (8) energy applications. (MOW)

  1. Nez Perce Tribal Hatchery Project, Operations and Maintenance and Planning and Design, 2001 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Larson, Roy Edward; Walker, Grant W.; Penney, Aaron K. (Nez Perce Tribe, Lapwai, ID)

    2006-03-01

    This report fulfills the contract obligations based on the Statement of Work (SOW) for the project as contracted with Bonneville Power Administration (BPA). Nez Perce Tribal Hatchery (NPTH) Year-2001 annual report combines information from two contracts with a combined value of $2,336,491. They are identified by Bonneville Power Administration as follows: (1) Operations and Maintenance--Project No. 1983-350-00, Contract No. 4504, and (2) Planning and Design--Project No. 1983-350-00, Contract No. 4035. The Operations and Maintenance (O&M) budget of $2,166,110 was divided as follows: Facility Development and Fish Production Costs--$860,463; and Equipment Purchases as capital cost--$1,305,647 for equipment and subcontracts. The Planning and Design (P&D) budget of $170,381 was allocated to development of a Coho master planning document in conjunction with Nez Perce Tribal Hatchery. The O&M budget expenditures represent personnel and fish production expenses; e.g., administration, management, coordination, facility development, personnel training and fish production costs for spring Chinook and Coho salmon. Under Objective 1: Fish Culture Training and Education, tribal staff worked at Clearwater Anadromous Hatchery (CAFH) an Idaho Department of Fish and Game (IDFG) facility to produce spring Chinook smolt and parr for release that are intended to provide future broodstock for NPTH. As a training exercise, BPA allowed tribal staff to rear Coho salmon at Dworshak National Fish Hatchery, a U.S. Fish and Wildlife Service (USFWS) facility. This statement of work allows this type of training to prepare tribal staff to later rear salmon at Nez Perce Tribal Hatchery under Task 1.6. As a subset of the O&M budget, the equipment purchase budget of $1,305,647 less $82,080 for subcontracts provides operational and portable equipment necessary for NPTH facilities after construction. The equipment budget for the year was $1,223,567; this year's purchases amounted $287,364.48 (see

  2. U.S. Annual Climatological Summaries

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Annual Climatological Summary contains historical monthly and annual summaries for over 8000 U.S. locations. Observing stations are located in the United States of...

  3. 2016 Annual Technology Baseline (ATB) - Webinar Presentation

    Energy Technology Data Exchange (ETDEWEB)

    Cole, Wesley; Kurup, Parthiv; Hand, Maureen; Feldman, David; Sigrin, Benjamin; Lantz, Eric; Stehly, Tyler; Augustine, Chad; Turchi, Craig; Porro, Gian; O' Connor, Patrick; Waldoch, Connor

    2016-09-13

    This deck was presented for the 2016 Annual Technology Baseline Webinar. The presentation describes the Annual Technology Baseline, which is a compilation of current and future cost and performance data for electricity generation technologies.

  4. Energy conversion & storage program. 1995 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Cairns, E.J.

    1996-06-01

    The 1995 annual report discusses laboratory activities in the Energy Conversion and Storage (EC&S) Program. The report is divided into three categories: electrochemistry, chemical applications, and material applications. Research performed in each category during 1995 is described. Specific research topics relate to the development of high-performance rechargeable batteries and fuel cells, the development of high-efficiency thermochemical processes for energy conversion, the characterization of new chemical processes and complex chemical species, and the study and application of novel materials related to energy conversion and transmission. Research projects focus on transport-process principles, chemical kinetics, thermodynamics, separation processes, organic and physical chemistry, novel materials and deposition technologies, and advanced methods of analysis.

  5. 5 CFR 2411.15 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Annual report. 2411.15 Section 2411.15....15 Annual report. On or before February 1 annually, the Chief FOIA Officer of the Authority shall submit a report of the activities of the Authority, the General Counsel, the Panel, and the IG...

  6. 9 CFR 2.36 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Annual report. 2.36 Section 2.36... WELFARE REGULATIONS Research Facilities § 2.36 Annual report. (a) The reporting facility shall be that... reporting facility shall submit an annual report to the AC Regional Director for the State where...

  7. 29 CFR 1401.37 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 4 2010-07-01 2010-07-01 false Annual report. 1401.37 Section 1401.37 Labor Regulations... Disclosure of Information § 1401.37 Annual report. The Office of the Director shall annually, within 60 days following the close of each calendar year, prepare a report covering each of the categories or records to...

  8. 32 CFR 806.25 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Annual report. 806.25 Section 806.25 National... INFORMATION ACT PROGRAM § 806.25 Annual report. (a) MAJCOM FOIA managers and AFLSA/JACL send a consolidated report for the fiscal year on DD Form 2564, Annual Report Freedom of Information Act, to HQ AFCIC/ITC...

  9. 34 CFR 601.20 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 3 2010-07-01 2010-07-01 false Annual report. 601.20 Section 601.20 Education... Covered Institutions and Institution-Affiliated Organizations § 601.20 Annual report. Each covered... preferred lender arrangement, must— (a) Prepare and submit to the Secretary an annual report, by a...

  10. 5 CFR 1631.18 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Annual report. 1631.18 Section 1631.18... Disclosure of Records Under the Freedom of Information Act, 5 U.S.C. 552 § 1631.18 Annual report. The Executive Director will submit annually, on or before February 1, a Freedom of Information report...

  11. Risø annual report 2001

    DEFF Research Database (Denmark)

    2002-01-01

    In this annual report, we present a small selection of Risø’s achievements in 2001. A more detailed review of Risø’s projects can be found in the Risø Annual Accounts for 2001 as well as in the annual progress reports prepared by the individual researchdepartments....

  12. 7 CFR 915.32 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 915.32 Section 915.32 Agriculture... Regulating Handling Administrative Body § 915.32 Annual report. The committee shall, as soon as practicable after the close of each fiscal year, prepare and mail an annual report to the Secretary, and to...

  13. 15 CFR 9.11 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Annual report. 9.11 Section 9.11... FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.11 Annual report. The Secretary will prepare an annual report of activities under the program, including an evaluation of...

  14. 42 CFR 1007.17 - Annual report.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 5 2010-10-01 2010-10-01 false Annual report. 1007.17 Section 1007.17 Public... STATE MEDICAID FRAUD CONTROL UNITS § 1007.17 Annual report. At least 60 days prior to the expiration of... (the first 9 months of the certification period for the first annual report), and containing...

  15. 45 CFR 1801.54 - Annual report.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Annual report. 1801.54 Section 1801.54 Public.... TRUMAN SCHOLARSHIP PROGRAM Payment Conditions and Procedures § 1801.54 Annual report. (a) Scholars with remaining eligibility for scholarship stipends must submit no later than July 15 an annual report to...

  16. 27 CFR 18.65 - Annual report.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Annual report. 18.65... OF THE TREASURY LIQUORS PRODUCTION OF VOLATILE FRUIT-FLAVOR CONCENTRATE Records and Reports § 18.65 Annual report. An annual report, on Form 1695(5520.2), of concentrate plant operations shall be...

  17. 11 CFR 2.8 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 11 Federal Elections 1 2010-01-01 2010-01-01 false Annual report. 2.8 Section 2.8 Federal Elections FEDERAL ELECTION COMMISSION SUNSHINE REGULATIONS; MEETINGS § 2.8 Annual report. The Commission shall report annually to Congress regarding its compliance with the requirements of the Government...

  18. 28 CFR 16.208 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Annual report. 16.208 Section 16.208 Judicial Administration DEPARTMENT OF JUSTICE PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION Public Observation of Parole Commission Meetings § 16.208 Annual report. The Commission shall report annually...

  19. 7 CFR 922.34 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 922.34 Section 922.34 Agriculture... IN WASHINGTON Order Regulating Handling Administrative Body § 922.34 Annual report. The committee shall, prior to the last day of each fiscal period, prepare and mail an annual report to the...

  20. 36 CFR 901.5 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Annual report. 901.5 Section... CORPORATION § 901.5 Annual report. The Executive Director shall prepare annually a comprehensive and detailed report of the Corporation's operations, activities, and accomplishments for the review of the Board...

  1. 42 CFR 457.750 - Annual report.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 4 2010-10-01 2010-10-01 false Annual report. 457.750 Section 457.750 Public..., Reporting, and Evaluation § 457.750 Annual report. (a) Report required for each Federal fiscal year. A State... State's assessment of the operation of the State plan. (b) Contents of annual report. In the...

  2. 32 CFR 48.601 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 1 2010-07-01 2010-07-01 false Annual report. 48.601 Section 48.601 National... SERVICEMAN'S FAMILY PROTECTION PLAN Miscellaneous § 48.601 Annual report. Information and data for the preparation of the annual report of the Board of Actuaries will be compiled by the Office of the Secretary...

  3. 36 CFR 330.8 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Annual report. 330.8 Section... § 330.8 Annual report. (RCS-DAEN-CWO-53) The Division Engineer will submit a consolidated annual report... October 1979. The report will contain the following: (a) Districts reporting. (b) Number assigned...

  4. 29 CFR 409.2 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 2 2010-07-01 2010-07-01 false Annual report. 409.2 Section 409.2 Labor Regulations... REPORTS BY SURETY COMPANIES § 409.2 Annual report. Each surety company having in force any bond required...-Management Standards a report, on U.S. Department of Labor Form S-1 entitled “Surety Company Annual Report”...

  5. 32 CFR 295.8 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 2 2010-07-01 2010-07-01 false Annual report. 295.8 Section 295.8 National... INFORMATION ACT PROGRAM OFFICE OF THE INSPECTOR GENERAL, FREEDOM OF INFORMATION ACT PROGRAM § 295.8 Annual report. The FOIA Annual Report, assigned Report Control System DD-PA (A) 1365, will be prepared by...

  6. 10 CFR 765.23 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Annual report. 765.23 Section 765.23 Energy DEPARTMENT OF... Procedures for Submitting and Processing Reimbursement Claims § 765.23 Annual report. The Department shall prepare annually a report summarizing pertinent information concerning claims submitted in the...

  7. 5 CFR 2502.19 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Annual report. 2502.19 Section 2502.19... Reproduction § 2502.19 Annual report. The General Counsel or his or her designee shall annually on or before March 1, submit a Freedom of Information report covering the preceding calendar year to the Speaker...

  8. 42 CFR 456.712 - Annual report.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 4 2010-10-01 2010-10-01 false Annual report. 456.712 Section 456.712 Public... Management System for Outpatient Drug Claims § 456.712 Annual report. (a) DUR Board report. The State must require the DUR Board to prepare and submit an annual DUR report to the Medicaid agency that...

  9. 7 CFR 916.34 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 916.34 Section 916.34 Agriculture... Regulating Handling Administrative Body § 916.34 Annual report. The committee shall, as soon as is practicable after the close of each marketing season, prepare and mail an annual report to the Secretary...

  10. 15 CFR 16.14 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Annual report. 16.14 Section 16.14 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY CONSUMER PRODUCT INFORMATION LABELING PROGRAM § 16.14 Annual report. The Secretary will prepare an annual report of...

  11. 7 CFR 920.34 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 920.34 Section 920.34 Agriculture... Administrative Body § 920.34 Annual report. The committee shall, as soon as is practicable after the close of each marketing season, prepare and mail an annual report to the Secretary and make a copy available...

  12. 7 CFR 923.34 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 923.34 Section 923.34 Agriculture... COUNTIES IN WASHINGTON Order Regulating Handling Administrative Body § 923.34 Annual report. The committee shall, prior to the last day of each fiscal period, prepare and mail an annual report to the...

  13. 23 CFR 1200.33 - Annual report.

    Science.gov (United States)

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Annual report. 1200.33 Section 1200.33 Highways NATIONAL... § 1200.33 Annual report. Within 90 days after the end of the fiscal year, each State shall submit an Annual Report. This report shall describe: (a) The State's progress in meeting its highway safety...

  14. 7 CFR 924.34 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 924.34 Section 924.34 Agriculture....34 Annual report. The committee shall, prior to the last day of each fiscal period, prepare and mail an annual report to the Secretary and make a copy available to each handler and grower who requests...

  15. 7 CFR 925.32 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 925.32 Section 925.32 Agriculture... SOUTHEASTERN CALIFORNIA Administrative Body § 925.32 Annual report. The committee should, as soon as practicable, after the close of each fiscal period, prepare and mail an annual report to the Secretary...

  16. 29 CFR 1610.21 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 4 2010-07-01 2010-07-01 false Annual report. 1610.21 Section 1610.21 Labor Regulations... Disclosure Under 5 U.S.C. 552 § 1610.21 Annual report. The Legal Counsel shall, on or before February 1, 1998, and annually thereafter, submit a Freedom of Information Act report covering the preceding fiscal...

  17. 7 CFR 947.35 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Annual report. 947.35 Section 947.35 Agriculture... Administrative Committee § 947.35 Annual report. The committee shall prepare and submit to the Secretary, within 2 months following the last day of each fiscal period, an annual report covering such fiscal...

  18. 45 CFR 2400.2 - Annual competition.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Annual competition. 2400.2 Section 2400.2 Public... FELLOWSHIP PROGRAM REQUIREMENTS General § 2400.2 Annual competition. To achieve its principal purposes, the Foundation holds an annual national competition to select teachers in grades 7-12, college seniors,...

  19. 76 FR 69239 - Annual Retail Trade Survey

    Science.gov (United States)

    2011-11-08

    ... survey, the Census Bureau will collect data covering annual sales, annual e-commerce sales, year-end... receivables, and, for selected industries, merchandise line sales, and percent of e-commerce sales to..., annual e-commerce sales, purchases, total operating expenses, accounts receivables, and...

  20. 77 FR 16484 - Annual Stress Test

    Science.gov (United States)

    2012-03-21

    ... Office of the Comptroller of the Currency 12 CFR Part 46 RIN 1557-AD58 Annual Stress Test AGENCY: Office... with total consolidated assets of more than $10 billion to conduct an annual stress test and comply... consolidated assets in excess of $10 billion to conduct annual stress tests pursuant to regulations...

  1. 45 CFR 1176.5 - Annual plan.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Annual plan. 1176.5 Section 1176.5 Public Welfare... ENDOWMENT FOR THE HUMANITIES PART-TIME CAREER EMPLOYMENT § 1176.5 Annual plan. (a) An agencywide plan for promoting part-time employment opportunities will be developed annually. This plan will establish...

  2. 基于4R理论的建筑劳务分包企业营销策略研究%Research on the Marketing Strategy in Labor Subcontracting Enterprises Based on 4R Theory

    Institute of Scientific and Technical Information of China (English)

    庞永师; 李水源; 蒋雨含; 刘景矿

    2014-01-01

    在激烈的建筑市场竞争环境下,劳务分包企业提高自身的队伍职业素质,采取创新的市场营销策略,树立企业品牌尤为必要。在分析和评述国内外建筑市场营销策略研究现状基础上,提出以“4R”营销理论为核心,以支持建筑劳务分包企业的业务承接模式为出发点,建立了由企业关联策略、企业反应策略、企业关系策略、企业回报策略构成的建筑劳务分包企业市场营销策略模型,并结合案例,分析该模型的实际应用。研究成果对提高我国建筑劳务分包企业的核心竞争力,促进企业持续、健康、快速的发展具有一定的参考意义。%It is very necessary for labor subcontracting enterprises to improve their professional quality,use innovative marketing strategies and establish a corporate brand in the fierce competition of construction market environment. Based on studying the marketing strategies in domestic and international construction market,it will be more suitable to select the marketing theory of 4R as the core and select the business models as a starting point. This paper will contrapuntally put forward appropriate marketing strategy mode with the related strategies,response strategies,relationship strategies and return strategies and analyse the practical application of the model combined with a case. The results of this paper will have a certain reference significance on improving the core competitiveness and promoting sustained,healthy and rapid development of the construction labor subcontracting enterprises in China.

  3. Annual report to Congress 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    Section 205 of the Department of Energy Organization Act of 1977 established the Energy Information Administration (EIA). One of the mandates in this legislation is that EIA prepare for Congress an annual report summarizing both activities and information collected and published. EIA`s major 1997 accomplishments are profiled in the body of this edition of the Annual Report to Congress. Appendix A contains abstracts of significant reports issued by EIA in 1997, and a chart of all titles and a list of all feature articles published during the year. Appendix B contains graphs of selected performance measures. Appendix C lists contact information for EIA subject matter specialists. Appendix D lists the major laws which form the basis of EIA`s legislative mandate.

  4. Secretary's annual report to Congress

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-01-01

    This second annual report of the DOE covers activities of all elements of the department except the independent FERC, which issues its own annual report. Individual chapters concern a posture statement, conservation, solar and other renewable energy, fossil energy, electric energy, nuclear energy, the environment, defense programs, international programs, general science programs, energy information, economic regulation, energy production, and support operations. The following appendixes are also included: foreign direct investments in US energy sources and supplies, exports of energy resources by foreign companies, major recipients of DOE funding, actions taken regarding disclosure of energy assets by DOE employees, financial assistance programs for alternative fuel demonstration facilities, and 1978 budget summary. 16 figures, 56 tables. (RWR)

  5. Annual report to Congress, 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-04-01

    Section 205 of the Department of Energy Organization Act of 1977 established the Energy Information Administration (EIA). One of the mandates in this legislation is that EIA prepare for Congress an annual report summarizing both activities and information collected and published. EIA`s major 1998 accomplishments are profiled in the body of this edition of the Annual Report to Congress. Appendix A contains abstracts of significant reports issued by EIA in 1998 and a chart of all titles and a list of all feature articles published during the year. Appendix B contains graphs of selected performance measures. Appendix C lists contact information for EIA subject matter specialists. Appendix D lists the major laws which form the basis of EIA`s legislative mandate.

  6. Determining Mean Annual Energy Production

    DEFF Research Database (Denmark)

    Kofoed, Jens Peter

    2016-01-01

    of energy for a wave energy converter or wave farm. Fundamentally, the MAEP is equal to the sum of the product of the power capture of a set of sea-states and their average annual occurrence. In general, it is necessary in the calculation of the MAEP to achieve a balance between computational demand......This robust book presents all the information required for numerical modelling of a wave energy converter, together with a comparative review of the different available techniques. The calculation of the mean annual energy production (MAEP) is critical to the assessment of the levelized cost...... obtained through system identification. The traditional method for representing the wave climate is using a scatter table, indexed by significant wave height and energy period; however, it has been found that this can lead to high errors in the MAEP due to the necessary assumptions regarding spectral shape...

  7. JAEA Takasaki annual report 2009

    OpenAIRE

    田中 茂

    2011-01-01

    JAEA Takasaki annual report 2009 describes research and development activities performed from April 1, 2009 to March 31, 2010 with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities (an electron accelerator and three 60Co gamma-ray irradiation facility) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research fields: (...

  8. JAEA Takasaki annual report 2008

    OpenAIRE

    田中 茂

    2009-01-01

    JAEA Takasaki annual report 2008 describes research and development activities performed from April 1, 2008 to March 31, 2009 with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities(an electron accelerator and three 60Co gamma-ray irradiation facilities) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research fields: ...

  9. JAEA Takasaki annual report 2010

    OpenAIRE

    小嶋 拓治

    2012-01-01

    JAEA Takasaki annual report 2010 describes research and development activities performed from April 1, 2010 to March 31, 2011 with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA), and electron/gamma-ray irradiation facilities at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research fields: (1) Space, Nuclear and Energy Engineering, (2) Environmental Conservation and Resource Exploitat...

  10. JAEA Takasaki annual report 2013

    OpenAIRE

    小嶋 拓治

    2015-01-01

    JAEA Takasaki annual report 2013 describes research and development activities performed from April 1, 2013 to March 31, 2014 mainly with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities (an electron accelerator and three 60Co gamma-ray irradiation facilities) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research ...

  11. JAEA Takasaki annual report 2014

    OpenAIRE

    横田 渉

    2016-01-01

    JAEA Takasaki annual report 2014 describes research and development activities performed from April 1, 2014 to March 31, 2015 mainly with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities (an electron accelerator and three 60Co gamma-ray irradiation facilities) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research ...

  12. JAEA Takasaki annual report 2007

    OpenAIRE

    田中 茂

    2008-01-01

    JAEA Takasaki annual report 2007 describes research and development activities performed from April 1, 2007 to March 31, 2008 with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities (an electron accelerator and three 60Co gamma-ray irradiation facilities) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research fields:...

  13. JAEA Takasaki annual report 2006

    OpenAIRE

    田中 茂

    2008-01-01

    JAEA Takasaki annual report 2006 describes research and development activities performed from April 1, 2006 to March 31, 2007 with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities (an electron accelerator and three 60Co gamma-ray irradiation facilities) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research fields:...

  14. JAEA Takasaki annual report 2011

    OpenAIRE

    小嶋 拓治

    2013-01-01

    JAEA Takasaki annual report 2011 describes research and development activities performed from April 1, 2011 to March 31, 2012 with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities (an electro accelerator and three 60Co gamma-ray irradiation facilities) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research fields: ...

  15. JAEA Takasaki annual report 2012

    OpenAIRE

    小嶋 拓治

    2014-01-01

    JAEA Takasaki annual report 2012 describes research and development activities performed from April 1, 2012 to March 31, 2013 mainly with Takasaki Ion Accelerators for Advanced Radiation Application (TIARA, four ion accelerators), and electron/gamma-ray irradiation facilities (an electron accelerator and three 60Co gamma-ray irradiation facilities) at Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA Takasaki). These activities are classified into four research ...

  16. Annual Report Fiscal Year 1981.

    Science.gov (United States)

    1982-01-01

    Director for Supply and Distribution, DRC >-M-S PROJECT OFFICER: Alan J. Kaplan/Arthur Hutchison ABSTRACT: A significant number of CCSS transactions...the same reason. Other Professional Activities Mr. Kaplan continued as a referee for INFOR and refereed one paper during the year. Mr. Kruse is now a... referee for Operations Research and Management Science and refereed one paper for each during the year. Mr. Rosenman gave what seems to be his annual

  17. CAES Annual Report FY 2011

    Energy Technology Data Exchange (ETDEWEB)

    Kortny Rolston

    2011-10-01

    The Center for Advanced Energy Studies was created to lead research programs important to the nation, attract students and faculty to the Idaho universities and act as a catalyst for technology-based economic development. CAES is striving to meet those goals by continuing to develop its infrastructure and equipment capabilities, expand its research portfolio and bolster Idaho's energy workforce. This Annual Report details the progress CAES made in FY 2011 toward fulfilling its research, education and economic development missions.

  18. 2016 Annual Technology Baseline (ATB)

    Energy Technology Data Exchange (ETDEWEB)

    Cole, Wesley; Kurup, Parthiv; Hand, Maureen; Feldman, David; Sigrin, Benjamin; Lantz, Eric; Stehly, Tyler; Augustine, Chad; Turchi, Craig; O' Connor, Patrick; Waldoch, Connor

    2016-09-01

    Consistent cost and performance data for various electricity generation technologies can be difficult to find and may change frequently for certain technologies. With the Annual Technology Baseline (ATB), National Renewable Energy Laboratory provides an organized and centralized dataset that was reviewed by internal and external experts. It uses the best information from the Department of Energy laboratory's renewable energy analysts and Energy Information Administration information for conventional technologies. The ATB will be updated annually in order to provide an up-to-date repository of current and future cost and performance data. Going forward, we plan to revise and refine the values using best available information. The ATB includes both a presentation with notes (PDF) and an associated Excel Workbook. The ATB includes the following electricity generation technologies: land-based wind; offshore wind; utility-scale solar PV; concentrating solar power; geothermal power; hydropower plants (upgrades to existing facilities, powering non-powered dams, and new stream-reach development); conventional coal; coal with carbon capture and sequestration; integrated gasification combined cycle coal; natural gas combustion turbines; natural gas combined cycle; conventional biopower. Nuclear laboratory's renewable energy analysts and Energy Information Administration information for conventional technologies. The ATB will be updated annually in order to provide an up-to-date repository of current and future cost and performance data. Going forward, we plan to revise and refine the values using best available information.

  19. Low-cost manufacturing of the point focus concentrating module and its key component, the Fresnel lens. Final subcontract report, 31 January 1991--6 May 1991

    Energy Technology Data Exchange (ETDEWEB)

    Saifee, T.; Konnerth, A. III [Solar Kinetics, Inc., Dallas, TX (United States)

    1991-11-01

    Solar Kinetics, Inc. (SKI) has been developing point-focus concentrating PV modules since 1986. SKI is currently in position to manufacture between 200 to 600 kilowatts annually of the current design by a combination of manual and semi-automated methods. This report reviews the current status of module manufacture and specifies the required approach to achieve a high-volume manufacturing capability and low cost. The approach taken will include process development concurrent with module design for automated manufacturing. The current effort reviews the major manufacturing costs and identifies components and processes whose improvements would produce the greatest effect on manufacturability and cost reduction. The Fresnel lens is one such key component. Investigating specific alternative manufacturing methods and sources has substantially reduced the lens costs and has exceeded the DOE cost-reduction goals. 15 refs.

  20. NREL Photovoltaic Program FY 1996 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    1997-08-01

    This report summarizes the in-house and subcontract research and development (R&D) activities under the National Renewable Energy Laboratory (NREL) Photovoltaics (PV) Program from October 1, 1995 through September 30, 1996 (fiscal year [FY] 1996). The NREL PV Program is part of the U.S. Department of Energy's (DOE) National Photovoltaics Program, as described in the DOE Photovoltaics Program Plan, FY 1991 - FY 1995. The mission of the DOE National Photovoltaics Program is to: "Work in partnership with U.S. industry to develop and deploy photovoltaic technology for generating economically competitive electric power, making photovoltaics an important contributor to the nation's and the world's energy use and environmental improvement. The two primary goals of the national program are to (1) maintain the U.S. PV industry's world leadership in research and technology development and (2) help the U.S. industry remain a major, profitable force in the world market. The NREL PV Program provides leadership and support to the national program toward achieving its mission and goals.

  1. Annual Workshop: Higgs Couplings 2016

    CERN Document Server

    2016-01-01

    Higgs Couplings 2016 is this year's installment of an annual workshop devoted to new experimental and theoretical results on the Higgs boson. The 2016 workshop will present the latest results from the LHC run 2 on the Higgs boson mass, spin/parity, and couplings and will present new theoretical work devoted to the measurement of Higgs parameters and possibilities for exotic Higgs decays. The workshop will provide an opportunity for critical discussion of the current strategies for studying the Higgs boson at the LHC and the next steps in the LHC program. The workshop will also include discussion of the longer-term Higgs boson program at future facilities.

  2. Annual review in automatic programming

    CERN Document Server

    Goodman, Richard

    2014-01-01

    Annual Review in Automatic Programming focuses on the techniques of automatic programming used with digital computers. Topics covered range from the design of machine-independent programming languages to the use of recursive procedures in ALGOL 60. A multi-pass translation scheme for ALGOL 60 is described, along with some commercial source languages. The structure and use of the syntax-directed compiler is also considered.Comprised of 12 chapters, this volume begins with a discussion on the basic ideas involved in the description of a computing process as a program for a computer, expressed in

  3. Annual report 1993-94

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    The annual report of the Ministry presents the activities of the Ministry`s departments: Corporate (public affairs and communications, employment equity, policy, planning and legislation, management services); BC Environment (environmental protection, fisheries, wildlife and habitat protection, environment regional operations); BC Lands (lands and water management, lands regional operations, lands services, water management); BC Parks (provincial parks, ecological reserves, outdoor recreation); Agencies, Boards, and Commissions (Commission on Waste Reduction, Soils, and Hazardous Wastes, Environmental Appeal Board); and Immigration and Multiculturalism (immigration policy, business immigration, multiculturalism BC, and BC Council of Human Rights). An organizational chart and financial overview are also included.

  4. Proceedings of NHA Annual Conferences

    Energy Technology Data Exchange (ETDEWEB)

    Debbi L. Smith

    2004-06-30

    The Proceedings of "Hydrogen: A Clean Energy Choice" and the 16th Annual U.S. Hydrogen Conference, "Partnering for the Global Hydrogen Future" include the presentations of high-level keynote speakers from the U.S. Department of Energy, the state government of California, Ambassadors and Executives of large corporations and emerging companies all presenting their vision on a future fueled by hydrogen. Parallel technical sessions informed attendees of developments in hydrogen technology R&D, commercial product development and market readiness. Persentations of the Student Design Competition Finalists are also included.

  5. Annual reports on NMR spectroscopy

    CERN Document Server

    Webb, Graham A; McCarthy, M J

    1995-01-01

    Over recent years, no other technique has grown to such importance as that of NMR spectroscopy. It is used in all branches of science where precise structural determination is required and where the nature of interactions and reactions in solution is being studied. Annual Reports on NMR Spectroscopy has established itself as a means for the specialist and non-specialist alike to become familiar with new applications of the technique in all branches of chemistry, including biochemistry, and pharmaceutics. This volume focuses on theoretical aspects of NMR nuclear shielding and on applications of

  6. Annual review in automatic programming

    CERN Document Server

    Goodman, Richard

    2014-01-01

    Annual Review in Automatic Programming, Volume 4 is a collection of papers that deals with the GIER ALGOL compiler, a parameterized compiler based on mechanical linguistics, and the JOVIAL language. A couple of papers describes a commercial use of stacks, an IBM system, and what an ideal computer program support system should be. One paper reviews the system of compilation, the development of a more advanced language, programming techniques, machine independence, and program transfer to other machines. Another paper describes the ALGOL 60 system for the GIER machine including running ALGOL pro

  7. Presentation at Innoventure Annual Competition

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-03-31

    This report documents the components of the workshop presented at the recent annual competition for the Innoventure program. The goal of the workshop was to focus on the delivery of science, technology, engineering, and math (STEM) concepts in a hands-on experiential learning format to increase interest in national security careers at NNSA, most of which are in the STEM fields. This work is a part of the National Security Preparedness Project (NSPP), being performed under a Department of Energy (DOE)/National Nuclear Security Administration (NNSA) grant.

  8. Annual Report 2001; Aarsrapport 2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This is the annual report 2001 for the TotalFinaElf oil company. This concern operates in more than 100 countries and covers all aspects of the energy industry, from oil- and gas exploration and production to refining and marketing of refined products and international trade with both unrefined and refined products. Through the Atofina division the concern is also a major player in the chemicals markets. The demonstrated reserves of TotalFinaElf has been calculated to more than ten billion barrels of oil equivalents. At a rate of 2.1 million barrels a day this ensures 14 years of production.

  9. 2011 ANNUAL SITE ENVIRONMENTAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, A.; Eddy, T.; Jannik, T.; Terry, B.; Cauthen, K.; Coward, L.; Dunaway-Ackerman, J.; Wilson, M.; Hutchison, J.; O' Quinn, S.

    2012-10-01

    The Savannah River Site Environmental Report for 2011 (SRNS-STI-2012-00200) is prepared for the U.S. Department of Energy (DOE) according to requirements of DOE Order 231.1 B, “Environment, Safety and Health Reporting." The annual SRS Environmental Report has been produced for more than 50 years. Several hundred copies are and interested individuals. The report’s purpose is to: present summary environmental data that characterize site environmental management performance; describe compliance status with respect to environmental standards and requirements; highlight significant programs and efforts.

  10. CERT Research Annual Report 2009

    Science.gov (United States)

    2009-01-01

    FX) Techniques to Reverse Engineer Virtual Machines Stacy Prowell Mark Pleszkoch Cory F. Cohen Jeffrey S. Havrilla 7 A P P ly in g F u n C ti o...Computation Detects and Eliminates No-Op Code Function Hashing for Malicious Code Analysis Cory F. Cohen Jeffrey S. Havrilla 27 Fu n C ti o n H A S H...www.hex-rays.com/idapro/flirt.htm [4] Cohen, C., Havrilla , J., “Malware Clustering Based on Entry Points”, CERT Research Annual Report 2008 http

  11. Annual review in automatic programming

    CERN Document Server

    Goodman, Richard

    2014-01-01

    Annual Review in Automatic Programming, Volume 2 is a collection of papers that discusses the controversy about the suitability of COBOL as a common business oriented language, and the development of different common languages for scientific computation. A couple of papers describes the use of the Genie system in numerical calculation and analyzes Mercury autocode in terms of a phrase structure language, such as in the source language, target language, the order structure of ATLAS, and the meta-syntactical language of the assembly program. Other papers explain interference or an ""intermediate

  12. Low-temperature thermal energy storage program annual operating plan

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, H. W.; Eissenberg, D. M.

    1979-01-01

    The LTTES program operating plans for FY 1978 are described in terms of general program objectives and the technical activities being implemented to achieve these objectives. The program structure provides emphasis on several principal thrusts; namely, seasonal thermal storage, daily/short-term thermal storage, and waste heat recovery and reuse. A work breakdown structure (WBS) organizes the efforts being carried out in-house or through subcontract within each thrust area. Fiscal data are summarized in respect to thrust area, individual efforts, and funding source.

  13. LLNL NESHAPs 2002 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R J; Gallegos, G M; Peterson, S-R; Tate, P J; Bertoldo, N A; Wilson, K R; Althouse, P E; Larson, J M

    2003-06-01

    This annual report is prepared pursuant to the National Emission Standards for Hazardous Air Pollutants (NESHAPs; Title 40 Code of Federal Regulations [CFR] Part 61, Subpart H). Subpart H governs radionuclide emissions to air from Department of Energy (DOE) facilities. NESHAPs limits the emission of radionuclides to the ambient air from DOE facilities to levels resulting in an annual effective dose equivalent (EDE) of 10 mrem (100 {micro}Sv) to any member of the public. The EDEs for the Lawrence Livermore National Laboratory (LLNL) site-wide maximally exposed members of the public from operations in 2002 are summarized here: (1) Livermore site: 0.023 mrem (0.23 {micro}Sv) (43% from point-source emissions, 57% from diffuse-source emissions). The point-source emissions include gaseous tritium modeled as tritiated water vapor as directed by EPA Region IX; the resulting dose is used for compliance purposes; and (2) Site 300: 0.021 mrem (0.21 {micro}Sv) (85% from point-source emissions, 15% from diffuse-source emissions). The EDEs were calculated using the EPA-approved CAP88-PC air dispersion/dose-assessment model, except for doses for three diffuse sources, which were calculated from measured concentrations and dose coefficients. Site specific meteorological data, stack flow data, and emissions estimates based on radionuclide usage inventory data or continuous stack monitoring data were the specific inputs to CAP88-PC for each modeled source.

  14. LLNL NESHAPs 2003 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R J; Gallegos, G M; Peterson, S; Wilson, K R; Althouse, P E; Larson, J M; Bertoldo, N A; Tate, P J; Bowen, B

    2004-06-23

    This annual report is prepared pursuant to the National Emission Standards for Hazardous Air Pollutants (NESHAPs; Title 40 Code of Federal Regulations [CFR] Part 61, Subpart H). Subpart H governs radionuclide emissions to air from Department of Energy (DOE) facilities. NESHAPs limits the emission of radionuclides to the ambient air from DOE facilities to levels resulting in an annual effective dose equivalent (EDE) of 10 mrem (100 {micro}Sv) to any member of the public. The EDEs for the Lawrence Livermore National Laboratory (LLNL) site-wide maximally exposed members of the public from operations in 2003 are summarized here. Livermore site: 0.044 mrem (0.44 {micro}Sv) (55% from point-source emissions, 45% from diffuse-source emissions). The point-source emissions include gaseous tritium modeled as tritiated water vapor as directed by EPA Region IX; the resulting dose is used for compliance purposes. Site 300: 0.017 mrem (0.17 {micro}Sv) (98% from point-source emissions, 2% from diffuse-source emissions). The EDEs were calculated using the EPA-approved CAP88-PC air dispersion/dose-assessment model, except for doses for two diffuse sources that were estimated using measured concentrations and dose coefficients. Site specific meteorological data, stack flow data, and emissions estimates based on radionuclide usage inventory data or continuous stack monitoring data were the specific inputs to CAP88-PC for each modeled source.

  15. LLNL NESHAPs 1996 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Gallegos, G.M.

    1997-01-06

    This annual report is prepared pursuant to the National Emissions Standards for Hazardous Air Pollutants (NESHAPs) 40 CFR Part 61, Subpart H; Subpart H governs radionuclide emissions to air from Department of Energy (DOE) facilities. NESHAPs limits the emission of radionuclides to the ambient air from DOE facilities to levels resulting in an annual effective dose equivalent (EDE) of 10 mrem (10 microsieverts) to any member of the public. The EDEs for the Lawrence Livermore National Laboratory (LLNL) site-wide maximally exposed members of the public from 1996 operations were (1) Livermore site: 0. 093 mrem (0.93 microsievert) (52% from point-source emissions, 48% from diffuse-source emissions); (2) Site 300: 0.033 mrem (0.33 microsievert) (99% from point-source, 1% from diffuse-source emissions). The EDEs were generally calculated using the EPA-approved CAP88-PC air-dispersion/dose-assessment model. Site-specific meteorological data, stack flow data, and emissions estimates based on radionuclide inventory data or continuous-monitoring systems data were the specific input to CAP88-PC for each modeled source. 5 figs., 8 tabs.

  16. Seed dispersal of desert annuals.

    Science.gov (United States)

    Venable, D Lawrence; Flores-Martinez, Arturo; Muller-Landau, Helene C; Barron-Gafford, Greg; Becerra, Judith X

    2008-08-01

    We quantified seed dispersal in a guild of Sonoran Desert winter desert annuals at a protected natural field site in Tucson, Arizona, USA. Seed production was suppressed under shrub canopies, in the open areas between shrubs, or both by applying an herbicide prior to seed set in large, randomly assigned removal plots (10-30 m diameter). Seedlings were censused along transects crossing the reproductive suppression borders shortly after germination. Dispersal kernels were estimated for Pectocarya recurvata and Schismus barbatus from the change in seedling densities with distance from these borders via inverse modeling. Estimated dispersal distances were short, with most seeds traveling less than a meter. The adhesive seeds of P. recurvata went farther than the small S. barbatus seeds, which have no obvious dispersal adaptation. Seeds dispersed farther downslope than upslope and farther when dispersing into open areas than when dispersing into shrubs. Dispersal distances were short relative to the pattern of spatial heterogeneity created by the shrub and open space mosaic. This suggests that dispersal could contribute to local population buildup, possibly facilitating species coexistence. Overall, these results support the hypothesis that escape in time via delayed germination is likely to be more important for desert annuals than escape in space.

  17. NREL Photovoltaic Program. FY 1994 annual report, October 1, 1993--September 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    This report summarizes the in-house and subcontracted research and development activities under the National renewable Energy Laboratory (NREL) Photovoltaics (PV) program for fiscal year 1994. Research is organized under the following areas; PV program management; crystalline silicon and advanced devices; thin-film PV technologies; PV manufacturing; PV module and system performance and engineering; and PV applications and markets.

  18. NOAA Average Annual Salinity (3-Zone)

    Data.gov (United States)

    California Department of Resources — The 3-Zone Average Annual Salinity Digital Geography is a digital spatial framework developed using geographic information system (GIS) technology. These salinity...

  19. Annual Coded Wire Program Missing Production Groups, 1996 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Pastor, S.M. [Fish and Wildlife Service, Vancouver, WA (United States). Columbia River Fisheries Program Office

    1997-07-01

    In 1989 the Bonneville Power Administration (BPA) began funding the evaluation of production groups of juvenile anadromous fish not being coded-wire tagged for other programs. These groups were the ``Missing Production Groups``. Production fish released by the US Fish and Wildlife Service (USFWS) without representative coded-wire tags during the 1980`s are indicated as blank spaces on the survival graphs in this report. The objectives of the ``Missing Production Groups`` program are: to estimate the total survival of each production group, to estimate the contribution of each production group to various fisheries, and to prepare an annual report for all USFWS hatcheries in the Columbia River basin. Coded-wire tag recovery information will be used to evaluate the relative success of individual brood stocks. This information can also be used by salmon harvest managers to develop plans to allow the harvest of excess hatchery fish while protecting threatened, endangered, or other stocks of concern.

  20. Research on defects and transport in amorphous-silicon-based semiconductors. Final subcontract report, 20 February 1991--19 April 1994

    Energy Technology Data Exchange (ETDEWEB)

    Schiff, E.A.; Antoniadis, H.; Gu, Q.; Lee, J.K.; Wang, Q.; Zafar, S. [Syracuse Univ., NY (United States)

    1994-09-01

    This report describes work on three individual tasks as follows. (1) Electron and hole drift measurements in a-Si{sub 1-x}Ge{sub x}:H and a-Si{sub 1-x}C{sub x}:H p-i-n solar cells. Multijunction solar cells incorporating modified band gap a-Si:H in a triple-junction structure are generally viewed as the most promising avenue for achieving an amorphous silicon-based solar call with 15% stabilized conversion efficiency. The specific objective of this task was to document the mobilities and deep-trapping mobility-lifetime products for electrons and holes in a-Si{sub 1-x}Ge{sub x}:H and a-Si{sub 1-x}C{sub x}:H alloys materials. (2) Electroabsorption measurements and built-in potential (V{sub bi}) in solar cells. V{sub bi} in a p-i-n solar call may be limiting the open-circuit voltage (V{sub oc}) in wide-band-gap cells (E{sub g} > 1.8 eV) currently under investigation as the top cell for 15% triple junction devices. The research addressed four issues that need to be resolved before the method can yield an error less than 0.1 V for V{sub bi}. The details are presented in this report. (3) Defect relaxation and Shockley-Read kinetics in a-Si:H. Quantitative modeling of solar cells is usually based on Shockley-Read kinetics.`` An important assumption of this approach is that the rate of emission of a photocarrier trapped on a defect is independent of quasi-Fermi level location.

  1. Average monthly and annual climate maps for Bolivia

    KAUST Repository

    Vicente-Serrano, Sergio M.

    2015-02-24

    This study presents monthly and annual climate maps for relevant hydroclimatic variables in Bolivia. We used the most complete network of precipitation and temperature stations available in Bolivia, which passed a careful quality control and temporal homogenization procedure. Monthly average maps at the spatial resolution of 1 km were modeled by means of a regression-based approach using topographic and geographic variables as predictors. The monthly average maximum and minimum temperatures, precipitation and potential exoatmospheric solar radiation under clear sky conditions are used to estimate the monthly average atmospheric evaporative demand by means of the Hargreaves model. Finally, the average water balance is estimated on a monthly and annual scale for each 1 km cell by means of the difference between precipitation and atmospheric evaporative demand. The digital layers used to create the maps are available in the digital repository of the Spanish National Research Council.

  2. Novel R2R Manufacturable Photonic-Enhanced Thin Film Solar Cells; January 28, 2010 -- January 31, 2011

    Energy Technology Data Exchange (ETDEWEB)

    Slafer, D.; Dalal, V.

    2012-03-01

    Final subcontract report for PV Incubator project 'Novel R2R Manufacturable Photonic-Enhanced Thin Film Solar Cells.' The goal of this program was to produce tandem Si cells using photonic bandgap enhancement technology developed at ISU and Lightwave Power that would have an NREL-verified efficiency of 7.5% on 0.25 cm{sup 2} area tandem junction cell on plastic substrates. This goal was met and exceeded within the timeframe and budget of the program. On smaller area cells, the efficiency was even higher, {approx}9.5% (not verified by NREL). Appropriate polymers were developed to fabricate photonic and plasmonic devices on stainless steel, Kapton and PEN substrates. A novel photonic-plasmon structure was developed which shows a promise of improving light absorption in thin film cells, a better light absorption than by any other scheme.

  3. Annual report 1998-1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    This is the Annual Report of the Atomic Energy of Canada Limited for the year ending March 31, 1999 and summarizes the activities of AECL during the period 1998-1999. The Activities covered in this Report include the CANDU Reactor Business, with excellent progress reported on the construction of two 700 MWe-class CANDU reactors in Qinshan, China. In the Republic of Korea, Wolsong Unit entered into commercial operation and Wolsong Unit 4 achieved sustained nuclear reaction. The Report also covers AECL's R and D and Waste Management programs. In the R and D section, the report outlines the development of the CANFLEX fuel bundle, Fuel Channels, Reactor Safety, Code Validation, Fuels and Fuel Cycles as well as Heavy Water production. Progress in the Waste Management program is also discussed.

  4. 2008 annual CERN Road Race

    CERN Multimedia

    2008-01-01

    Dear runners, The 2008 annual CERN Road Race will be held on Wednesday 24 September at 6.00 p.m. This 5.4 km race consists of 3 laps of a 1.8 km circuit in the West Area of the Meyrin site and is open to everyone working at CERN and their families. Past races have attracted runners of all speeds, with times ranging from under 17 to over 34 minutes. The race is run on a handicap basis, with starting times staggered to ensure that (in theory) all runners finish together. However, if the popularity of the race continues to grow (95 runners took part last year), its format may be modified to a classic single start. For more information and to complete the online entry form, go to http://club-running.web.cern.ch

  5. Annual report to Congress, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1994-03-31

    Created by Congress in 1977 as an independent entity within the Department of Energy, the Energy Information Administration (EIA) is the principal and authoritative source of comprehensive energy data for the Congress, the Federal Government, the States, and the public. With the mandate to ``collect, assemble, evaluate, analyze, and disseminate data and information,`` EIA`s mission has been defined to: maintain a comprehensive data and information program relevant to energy resources and reserves, energy production, energy demand, energy technologies, and related financial and statistical information relevant to the adequacy of energy resources to meet the Nation`s demands in the near and longer term future. Develop and maintain analytical tool and collection and processing systems; provide analyses that are accurate, timely, and objective; and provide information dissemination services. This annual report summarizes EIA`s activities and accomplishments in 1993.

  6. Laser Program annual report 1984

    Energy Technology Data Exchange (ETDEWEB)

    Rufer, M.L.; Murphy, P.W. (eds.)

    1985-06-01

    The Laser Program Annual Report is part of the continuing series of reports documenting the progress of the unclassified Laser Fusion Program at the Lawrence Livermore National Laboratory (LLNL). As in previous years, the report is organized programmatically. The first section is an overview of the basic goals and directions of the LLNL Inertial Confinement Fusion (ICF) Program, and highlights the year's important accomplishments. Sections 2 through 7 provide the detailed information on the various program elements: Laser Systems and Operations, Target Design, Target Fabrication, Laser Experiments and Advanced Diagnostics, Advanced Laser Development, and Applications of Inertial Confinement Fusion. Individual sections will be indexed separately. 589 refs., 333 figs., 25 tabs.

  7. Laser program annual report 1983

    Energy Technology Data Exchange (ETDEWEB)

    Hendricks, C.D.; Rufer, M.L.; Murphy, P.W. (eds.)

    1984-06-01

    In the 1983 Laser Program Annual Report we present the accomplishments and unclassified activities of the Laser Program at Lawrence Livermore National laboratory (LLNL) for the year 1983. It should be noted that the report, of necessity, is a summary, and more detailed expositions of the research can be found in the many publications and reports authored by staff members in the Laser Program. The purpose of this report is to present our work in a brief form, but with sufficient depth to provide an overview of the analytical and experimental aspects of the LLNL Inertial-Confinement Fusion (ICF) Program. The format of this report is basically the same as that of previous years. Section 1 is an overview and highlights the important accomplishments and directions of the Program. Sections 2 through 7 provide the detailed information on the various major parts of the Program: Laser Systems and Operations, Target Design, Target Fabrication, Fusion Experiments, Laser Research and Development, and Energy Applications.

  8. LLNL NESHAPs 2014 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bertoldo, N. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gallegos, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); MacQueen, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wegrecki, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-07-01

    Lawrence Livermore National Security, LLC operates facilities at Lawrence Livermore National Laboratory (LLNL) where radionuclides are handled and stored. These facilities are subject to the U.S. Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants (NESHAPs) in Code of Federal Regulations (CFR) Title 40, Part 61, Subpart H, which regulates radionuclide emissions to air from Department of Energy (DOE) facilities. Specifically, NESHAPs limits the emission of radionuclides to the ambient air to levels resulting in an annual effective dose equivalent of 10 mrem (100 μSv) to any member of the public. Using measured and calculated emissions, and building-specific and common parameters, LLNL personnel applied the EPA-approved computer code, CAP88-PC, Version 4.0.1.17, to calculate the dose to the maximally exposed individual member of the public for the Livermore Site and Site 300.

  9. LLNL NESHAPs 1998 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Berger, R L; Bertoldo, N A; Biermann, A H; Gallegos, G; Hall, L C; Harrach, R J; Surano, K A

    1999-06-14

    This annual report is prepared pursuant to the National Emissions Standards for Hazardous Air Pollutants (NESHAPs) 40 CFR Part 61, Subpart H; Subpart H governs radionuclide emissions to air from Department of Energy (DOE) facilities. NESHAPs limits the emission of radionuclides to the ambient air from DOE facilities to levels resulting in an annual effective dose equivalent (EDE) of 10 mrem (100 {micro}Sv) to any member of the public. The EDEs for the Lawrence Livermore National Laboratory (LLNL) site-wide maximally exposed members of the public from 1998 operations are summarized here. (1) Livermore site: 0.055 mrem (0.55 {micro}Sv) (57% from point-source emissions, 43% from diffuse-source emissions). The point-source emissions include gaseous tritium modeled as tritiated water vapor as directed by EPA Region IX and is used for compliance purposes. LLNL believes a more realistic dose for the Livermore site is 0.049 mrem (0.49 {micro}Sv) (52% from point-source emissions, 48% from diffuse-source emissions). This dose is based on an assessment that represents a more realistic behavior of tritium gas in the environment. (2) Site 300: 0.024 mrem (0.24 {micro}Sv) (78% from point-source emissions, 22% from diffuse-source emissions). The EDEs were generally calculated using the EPA-approved CAP88-PC air-dispersion/dose-assessment model. Site-specific meteorological data, stack flow data, and emissions estimates based on radionuclide inventory data or continuous-monitoring systems data were the specific input to CAP88-PC for each modeled source.

  10. FY 1996 annual work plan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-30

    In April 1994, the Department of Energy (DOE) Strategic Plan was issued. This Plan presents the Department`s strategic outlook in response to a changing world. It discusses the Department`s unique capabilities; its mission, vision, and core values; and key customer and stakeholder considerations. The DOE Strategic Plan lists business strategies and critical success factors which are intended to aid the Department in accomplishing its mission and reaching its vision of itself in the future. The Office of Inspector General (OIG) has an important role in carrying out the goals and objectives of the Secretary`s Strategic Plan. The ultimate goal of the OIG is to facilitate positive change by assisting its customers, responsible Government officials, in taking actions to improve programs and operations. The Inspector General annually issues his own Strategic Plan that contains program guidance for the next fiscal year. As part of its responsibility in carrying out the OIG mission, the Office of the Deputy Inspector General for Audit Services (Office of Audit Services) publishes an Annual Work Plan that sets forth audits that are planned for the next fiscal year. Selection of these audits is based on the overall budget of the Department, analyses of trends in Departmental operations, guidance contained in the agency`s strategic plans, statutory requirements, and the expressed needs and audit suggestions of Departmental program managers and OIG managers and staff. This work plan includes audits that are carried over from FY 1995 and audits scheduled to start during FY 1996. Audits included in the plan will be performed by OIG staff.

  11. 7 CFR 1.20 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 1 2010-01-01 2010-01-01 false Annual report. 1.20 Section 1.20 Agriculture Office of the Secretary of Agriculture ADMINISTRATIVE REGULATIONS Official Records § 1.20 Annual report. (a... fiscal year basis beginning October 1, 1997, and report the following information to the Office...

  12. 47 CFR 101.1417 - Annual report.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Annual report. 101.1417 Section 101.1417... Annual report. Each MVDDS licensee shall file with the Broadband Division of the Wireless Telecommunications Bureau of the Commission two copies of a report by March 1 of each year for the preceding...

  13. 38 CFR 53.31 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Annual report. 53.31... Annual report. (a) A State receiving payment under this part shall provide to VA a report setting forth... incentive program has been in improving nurse staffing in the SVH. The report shall be provided to VA...

  14. 39 CFR 265.10 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 39 Postal Service 1 2010-07-01 2010-07-01 false Annual report. 265.10 Section 265.10 Postal... Annual report. A report concerning the administration of the Freedom of Information Act and this part..., with the first such report, for fiscal year 1998, due on or before February 1, 1999. Data for...

  15. 10 CFR 205.325 - Annual report.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Annual report. 205.325 Section 205.325 Energy DEPARTMENT OF ENERGY OIL ADMINISTRATIVE PROCEDURES AND SANCTIONS Electric Power System Permits and Reports... International Boundaries § 205.325 Annual report. Persons receiving permits to construct, connect, operate...

  16. 22 CFR 1411.12 - Annual report.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Annual report. 1411.12 Section 1411.12 Foreign... AVAILABILITY OF OFFICIAL INFORMATION § 1411.12 Annual report. On or before March 1 of each calendar year, the Executive Director of the Authority shall submit a report of the activities of the Board, the...

  17. 29 CFR 404.2 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 2 2010-07-01 2010-07-01 false Annual report. 404.2 Section 404.2 Labor Regulations... LABOR ORGANIZATION OFFICER AND EMPLOYEE REPORTS § 404.2 Annual report. Every labor organization officer..., within 90 days after the end of his fiscal year, a signed report containing the detailed...

  18. 29 CFR 405.2 - Annual report.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 2 2010-07-01 2010-07-01 false Annual report. 405.2 Section 405.2 Labor Regulations... EMPLOYER REPORTS § 405.2 Annual report. Every employer who in any fiscal year has made any payment, loan... Act to be reported, shall, as prescribed by the regulations in this part, file with the Office...

  19. 76 FR 64894 - Annual Wholesale Trade Survey

    Science.gov (United States)

    2011-10-19

    ... collect data covering annual sales, e-commerce sales, purchases, total operating expenses, year-end..., e- commerce sales, year-end inventories held inside and outside the United States, purchases, and... data covering annual sales, e-commerce sales, year-end inventories held inside and outside the...

  20. 12 CFR 346.7 - Annual reports.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Annual reports. 346.7 Section 346.7 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND STATEMENTS OF GENERAL POLICY DISCLOSURE AND... unaudited financial statements, audit report, or other report, so long as the annual report filed by...

  1. Second annual Dog Walk Against Cancer scheduled

    OpenAIRE

    Douglas, Jeffrey S.

    2005-01-01

    The second annual "Dog Walk Against Cancer" will be held from 10 a.m. to 2 p.m. Saturday, April 9, on the grounds of the Virginia-Maryland Regional College of Veterinary Medicine at Virginia Tech in Blacksburg. The event is open to the public and will be held in conjunction with the college's annual "Open House."

  2. 24 CFR 5.609 - Annual income.

    Science.gov (United States)

    2010-04-01

    ...-Based Assistance Family Income § 5.609 Annual income. (a) Annual income means all amounts, monetary or... of periodic amounts received from Social Security, annuities, insurance policies, retirement funds... provision must be received under employment training programs with clearly defined goals and objectives,...

  3. 42 CFR 419.50 - Annual review.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 3 2010-10-01 2010-10-01 false Annual review. 419.50 Section 419.50 Public Health... review. (a) General rule. Not less often than annually, CMS reviews and updates groups, relative payment... selection of representatives of providers to review (and advise CMS concerning) the clinical integrity...

  4. 75 FR 63805 - Annual Wholesale Trade Survey

    Science.gov (United States)

    2010-10-18

    ... Bureau of the Census Annual Wholesale Trade Survey AGENCY: Bureau of the Census, Commerce. ACTION: Notice... to conduct the 2010 Annual Wholesale Trade Survey (AWTS). AWTS covers firms with establishments...; manufacturers' sales branches and offices; and agents, brokers, and electronic markets. Through this survey,...

  5. 78 FR 68023 - Annual Wholesale Trade Survey

    Science.gov (United States)

    2013-11-13

    ... collect data covering annual sales, e- commerce sales, purchases, total operating expenses, year-end... Census Bureau will collect data covering sales, e-commerce sales, year-end inventories held inside and... offices, the Census Bureau will collect data covering annual sales, e-commerce sales, year-end...

  6. 77 FR 3166 - Annual Stress Test

    Science.gov (United States)

    2012-01-23

    ...-AD91 Annual Stress Test AGENCY: Federal Deposit Insurance Corporation. ACTION: Proposed rule with... stress tests (``proposed rule''). This proposed rule would implement section 165(i)(2) by requiring state... of more than $10 billion to conduct annual stress tests in accordance with the proposed rule,...

  7. Conducting the Annual Program Review: A Guide.

    Science.gov (United States)

    Drake Univ., Des Moines, IA. Midwest Regional Resource Center.

    Designed to assist local education agencies (LEAs) in conducting annual program reviews, the handbook focuses on evaluating Individualized Education Programs (IEPs) for handicapped children. An annual review meeting guide discusses purposes and procedures of the review. The second section provides a background on the planning-evaluation process,…

  8. Northeast Waste Management Alliance (NEWMA). Annual report FY 1993

    Energy Technology Data Exchange (ETDEWEB)

    Goland, A.N.; Kaplan, E.

    1993-11-01

    Funding was provided to Brookhaven National Laboratory in the fourth quarter of FY93 to establish a regional alliance as defined by Dr. Clyde Frank during his visit to BNL on March 7, 1993. In collaboration with the Long Island Research Institute (LIRI), BNL developed a business plan for the Northeast Waste Management Alliance (NEWMA). Concurrently, informal discussions were initiated with representatives of the waste management industry, and meetings were held with local and state regulatory and governmental personnel to obtain their enthusiasm and involvement. A subcontract to LIRI was written to enable it to formalize interactions with companies offering new waste management technologies selected for their dual value to the DOE and local governments in the Northeast. LIRI was founded to develop and coordinate economic growth via introduction of new technologies. As a not-for-profit institution it is in an ideal position to manage the development of NEWMA through ready access to venture capital and strong interactions with the business community, universities, and BNL. Another subcontract was written with a professor at SUNY/Stony Brook to perform an evaluation of new pyrolitic processes, some of which may be appropriate for development by NEWMA. Independent endorsement of the business plan recently by another organization, GETF, with broad knowledge of DOE/EM-50 objectives, provides a further incentive for moving rapidly to implement the NEWMA strategy. This report describes progress made during the last quarter of FY93.

  9. Department of Thermonuclear Research annual report 1992

    Energy Technology Data Exchange (ETDEWEB)

    Sadowski, M.; Pawlowicz, W. [eds.] [Soltan Inst. for Nuclear Studies, Otwock-Swierk (Poland)

    1993-02-01

    Department of Thermonuclear Research annual report 1992 presents the most important results of theoretical, experimental and technological studies carried out within a framework of the research program - Plasma Physics and an additional grant - Study of Surface Melting of Selected Materials with a Plasma stream (contract with the Committee for Scientific Research - KBN). Theoretical studies of tokamak edge plasmas, atomic collisions, heat transfer, and numerical codes, are shortly summarized. Experimental studies of X-rays and particles emitted from Plasma-Focus facilities, calibration of nuclear track detectors, optimization of PF discharges with additional gas targets, magnetic probe measurements, new diagnostic and experimental arrangements, as well as mass- and energy-analysis of ions from IONOTRON-type devices, are described. Also presented are technological studies, modernization of experimental facilities, design of new control systems, tests on uniformity and reproducibility of plasma streams as the formation of photovoltaic cells and modifications of solid surfaces by means of plasma streams from the IONOTRON and PF devices. (author).

  10. Development of large-area monolithically integrated silicon-film{trademark} photovoltaic modules. Final subcontract report, May 1, 1991--December 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Hall, R.B.; Rand, J.A.; Cotter, J.E. [AstroPower, Inc., Newark, DE (United States)

    1995-04-01

    The objective of this program is to develop Silicon Film{trademark} Product III into a low-cost, stable solar cell for large-scale terrestrial power applications. The Product III structure is a thin (<100 {mu}m) polycrystalline layer of silicon on a durable, insulating, ceramic substrate. The insulating substrate allows the silicon layer to be isolated and metallized to form a monolithically interconnected array of solar cells. High efficiency is achieved by the use of light trapping and passivated surfaces. This project focused on the development of five key technologies associated with the monolithic sub-module device structure: (1) development of the film deposition and growth processes; (2) development of the low-cost ceramic substrate; (3) development of a metallurgical barrier technology; (4) development of sub-element solar cell processing techniques; and (5) development of sub-module (isolation and interconnection) processes. This report covers the development approaches and results relating to these technologies. Significant progress has been made in the development of all of the related technologies. This is evidenced by the fabrication of a working 12.0 cm{sup 2} prototype sub-module consisting of 7 elements and testing with an open circuit voltage of 3.9 volts, a short circuit current of 35.2 mA and a fill factor of 63% and an overall efficiency of 7.3%. Another significant result achieved is a 13.4% (NREL verified), 1.0 cm{sup 2} solar cell fabricated from material deposited and grown on a graphite cloth substrate. The significant technological hurdle of the program was and remains the low quality of the photovoltaic layer which is caused by contamination of the photovoltaic layer from the low-cost ceramic substrate by trace impurities found in the substrate precursor materials. The ceramic substrate and metallurgical barrier are being developed specifically to solve this problem.

  11. Commercialization of New Lattice-Matched Multi-Junction Solar Cells Based on Dilute Nitrides: July 8, 2010 - March 7, 2012

    Energy Technology Data Exchange (ETDEWEB)

    Herb, J.

    2012-04-01

    Final Technical Progress Report for PV Incubator subcontract NAT-0-99013-03. The overall objective of this Incubator subcontract was to complete the work necessary to make commercial ready solar cells using the dilute nitride technology. The specific objectives of this program were aimed at completing the development of a triple-junction solar cell that incorporates a GaInNAs {approx}1eV subcell to the point of commercial readiness, and determining the cell reliability and, if necessary, identifying and eliminating process or material related issues that lead to early-life cell failures. There were three major objectives for Phase 1, each of which focuses on a key element of the solar cell that determines its performance in a commercial CPV system. One objective was to optimize the quality and performance of the key individual components making up the solar cell structure and then to optimize the integration of these components into a complete triple-junction cell. A second objective was to design and test anti-reflective coating that maximizes the light coupled into a 3J cell with a {approx}1 eV bottom cell bandgap. The third objective was to develop Highly Accelerated Life Tests (HALT) protocols and tools for identifying and correcting potential reliability problems. The Phase 2 objectives were a continuation of the work begun in Phase 1 but aimed at optimizing cell performance for commercial requirements. Phase 2 had four primary objectives: (1) develop a glass-matched anti-reflective coating (ARC) and optimize the cell/ARC to give good performance at 60C operating temperature, (2) optimize the cell for good operation at 60C and high concentration, and (3) complete the light biased HALT system and use it to determine what, if any, failures are observed, and (4) determine the reliability limits of the optimized cell.

  12. EDITORIAL: Annual prizes for best papers

    Science.gov (United States)

    2006-09-01

    2005 Roberts Prize The publishers of Physics in Medicine and Biology (PMB) in association with the Institute of Physics and Engineering in Medicine (IPEM) jointly award an annual prize for an article published in PMB during the previous year. The following 14 articles, listed below in chronological order, were rated the best of 2005 based on the (two or three) referees' assessments: P Kundrát et al 2005 Probabilistic two-stage model of cell inactivation by ionizing particles Phys. Med. Biol. 50 1433-47 D Arora et al 2005 Direct thermal dose control of constrained focused ultrasound treatments: phantom and in vivo evaluation Phys. Med. Biol. 50 1919-35 J S Dysart et al 2005 Characterization of Photofrin photobleaching for singlet oxygen dose estimation during photodynamic therapy of MLL cells in vitro Phys. Med. Biol. 50 2597-616 M Defrise et al 2005 Fourier rebinning of time-of-flight PET data Phys. Med. Biol. 50 2749-63 Z Su et al 2005 Systematic investigation of the signal properties of polycrystalline HgI2 detectors under mammographic, radiographic, fluoroscopic and radiotherapy irradiation conditions Phys. Med. Biol. 50 2907-28 E Bräuer-Krisch et al 2005 New irradiation geometry for microbeam radiation therapy Phys. Med. Biol. 50 3103-11 H C Pyo et al 2005 Identification of current density distribution in electrically conducting subject with anisotropic conductivity distribution Phys. Med. Biol. 50 3183-96 R P Findlay et al 2005 Effects of posture on FDTD calculations of specific absorption rate in a voxel model of the human body Phys. Med. Biol. 50 3825-35 G Alexandrakis et al 2005 Tomographic bioluminescence imaging by use of a combined optical-PET (OPET) system: a computer simulation feasibility study Phys. Med. Biol. 50 4225-41 J Keshvari et al 2005 Comparison of radio frequency energy absorption in ear and eye region of children and adults at 900, 1800 and 2450 MHz Phys. Med. Biol. 50 4355-69 J Laufer et al 2005 In vitro measurements of absolute blood

  13. Cells

    Directory of Open Access Journals (Sweden)

    Zhao-Hui Jin

    2012-11-01

    Full Text Available As cancer stem cells (CSCs are postulated to play critical roles in cancer development, including metastasis and recurrence, CSC imaging would provide valuable information for cancer treatment and lead to CSC-targeted therapy. To assess the possibility of in vivo CSC targeting, we conducted basic studies on radioimmunotargeting of cancer cells positive for CD133, a CSC marker recognized in various cancers. Antibodies against CD133 were labeled with 125I, and their in vitro cell binding properties were tested. Using the same isotype IgG as a control, in vivo biodistribution of the labeled antibody retaining immunoreactivity was examined in mice bearing an HCT116 xenograft in which a population of the cancer cells expressed CD133. Intratumoral distribution of the labeled antibody was examined and compared to the CD133 expression pattern. The 125I-labeled anti-CD133 antibody showed a modest but significantly higher accumulation in the HCT116 xenograft compared to the control IgG. The intratumoral distribution of the labeled antibody mostly overlapped with the CD133 expression, whereas the control IgG was found in the area close to the necrotic tumor center. Our results indicate that noninvasive in vivo targeting of CSCs could be possible with radiolabeled antibodies against cell membrane markers.

  14. LLNL NESHAPs 2001 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R.J.; Peterson, S.-R.; Gallegos, G.M.; Tate, P.J.; Bertoldo, N.A.; Althouse, P.E.

    2002-06-18

    NESHAPs limits the emission of radionuclides to the ambient air from DOE facilities to levels resulting in an annual effective dose equivalent (EDE) of 10 mrem (100 {micro}Sv) to any member of the public. The EDEs for the Lawrence Livermore National Laboratory (LLNL) site-wide maximally exposed members of the public from operations in 2001 are summarized here: (1) Livermore site: 0.017 mrem (0.17 {micro}Sv) (34% from point-source emissions, 66% from diffuse-source emissions), The point-source emissions include gaseous tritium modeled as tritiated water vapor as directed by EPA Region IX; the resulting dose is used for compliance purposes; and (2) Site 300: 0.054 mrem (0.54 {micro}Sv) (93% from point-source emissions, 7% from diffuse-source emissions); The EDEs were calculated using the EPA-approved CAP88-PC air dispersion/dose assessment model, except for doses for three diffuse sources, which were calculated from measured concentrations and dose coefficients. Site specific meteorological data, stack flow data, and emissions estimates based on radionuclide usage inventory data or continuous stack monitoring data were the specific inputs to CAP88-PC for each modeled source.

  15. Annual Site Environmental Report: 2005

    Energy Technology Data Exchange (ETDEWEB)

    sabba, d

    2007-02-03

    This report provides information about environmental programs during 2005 at the Stanford Linear Accelerator Center (SLAC). Seasonal activities that span calendar years are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M&O contractor. SLAC effectively applied environmental management in meeting the site's integrated safety and environmental management system (ISEMS) goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2005, SLAC focused on these activities through the SLAC management systems (described in Chapter 3). These systems were also the way SLAC approached implementing ''greening of the government'' initiatives such as Executive Order 13148. The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. There were no reportable releases to the environment from SLAC operations during 2005. In addition, many improvements were continued during 2005, in waste minimization, recycling, stormwater drain system, groundwater restoration, and implementing a chemical management system (CMS) to better manage chemical use. Program-specific details are discussed.

  16. SRNL LDRD ANNUAL REPORT 2008

    Energy Technology Data Exchange (ETDEWEB)

    French, T

    2008-12-29

    The Laboratory Director is pleased to have the opportunity to present the 2008 Laboratory Directed Research and Development (LDRD) annual report. This is my first opportunity to do so, and only the second such report that has been issued. As will be obvious, SRNL has built upon the excellent start that was made with the LDRD program last year, and researchers have broken new ground in some important areas. In reviewing the output of this program this year, it is clear that the researchers implemented their ideas with creativity, skill and enthusiasm. It is gratifying to see this level of participation, because the LDRD program remains a key part of meeting SRNL's and DOE's strategic goals, and helps lay a solid scientific foundation for SRNL as the premier applied science laboratory. I also believe that the LDRD program's results this year have demonstrated SRNL's value as the EM Corporate Laboratory, having advanced knowledge in a spectrum of areas, including reduction of the technical risks of cleanup, separations science, packaging and transportation of nuclear materials, and many others. The research in support of Energy Security and National and Homeland Security has been no less notable. SRNL' s researchers have shown again that the nascent LDRD program is a sound investment for DOE that will pay off handsomely for the nation as time goes on.

  17. LLNL NESHAPs 2008 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Bertoldo, N; Gallegos, G; MacQueen, D; Wegrecki, A; Wilson, K

    2009-06-25

    Lawrence Livermore National Security, LLC operates facilities at Lawrence Livermore National Laboratory (LLNL) where radionuclides are handled and stored. These facilities are subject to the U.S. Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants (NESHAPs) in Code of Federal Regulations (CFR) Title 40, Part 61, Subpart H, which regulates radionuclide emissions to air from Department of Energy (DOE) facilities. Specifically, NESHAPs limits the emission of radionuclides to the ambient air to levels resulting in an annual effective dose equivalent of 10 mrem (100 {mu}Sv) to any member of the public. Using measured and calculated emissions, and building-specific and common parameters, LLNL personnel applied the EPA-approved computer code, CAP88-PC, Version 1.0, to calculate the dose to the maximally exposed individual for the Livermore site and Site 300. The dose for the LLNL site-wide maximally exposed members of the public from operations in 2008 are summarized here: {sm_bullet} Livermore site: 0.0013 mrem (0.013 {mu}Sv) (26% from point source emissions, 74% from diffuse source emissions). The point source emissions include gaseous tritium modeled as tritiated water vapor as directed by EPA Region IX; the resulting dose is used for compliance purposes. {sm_bullet} Site 300: 0.000000044 mrem (0.00000044 {mu}Sv) (100% from point source emissions).

  18. Annual report 1997-1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    Atomic Energy of Canada Limited (AECL) was established in 1952 as a Crown Corporation and reports to parliament through the Minister of Natural Resources. As an annual report, financial statements are an integral element, financial analysis and review are also ongoing. AECL is very active in marketing the science culture which is key to public understanding and acceptance of the nuclear industry. In commercial operations, the CANDU is still the flagship to be marketed in many countries. AECL is the main producer of medical isotopes for the global market. AECL and MDS Nordion signed agreements to secure the ongoing supply of isotopes and to build and operate two MAPLE reactors at the Chalk River site. Activities at AECL are focused on improved economics, further enhanced safety systems and fuel cycle flexibility in the research and product development programs. Waste management and nuclear sciences i e. health and environmental sciences are ongoing studies. Site refurbishment focuses on replacing and refurbishing major facilities to meet business needs.

  19. LLNL NESHAPs, 1993 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R.J.; Surano, K.A.; Biermann, A.H.; Gouveia, F.J.; Fields, B.C.; Tate, P.J.

    1994-06-01

    The standard defined in NESHAPSs CFR Part 61.92 limits the emission of radionuclides to the ambient air from DOE facilities to those that would cause any member of the public to receive in any year an effective dose equivalent of 10 mrem. In August 1993 DOE and EPA signed a Federal Facility Compliance Agreement which established a schedule of work for LLNL to perform to demonstrate compliance with NESHAPs, 40 CFR part 61, Subpart H. The progress in LLNL`s NESHAPs program - evaluations of all emission points for the Livermore site and Site 300, of collective EDEs for populations within 80 km of each site, status in reguard to continuous monitoring requirements and periodic confirmatory measurements, improvements in the sampling and monitoring systems and progress on a NESHAPs quality assurance program - is described in this annual report. In April 1994 the EPA notified DOE and LLNL that all requirements of the FFCA had been met, and that LLNL was in compliance with the NESHAPs regulations.

  20. EDF group. Annual report 2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-05-01

    This document is the English version of the 2001 annual report of Electricite de France (EdF) Group, the French electric utility. It comprises 4 parts: introduction (statement of the chairman and chief executive officer, corporate governance, group key figures, sustainable growth indicators - parent company, energy for a sustainable future, EdF group worldwide); dynamics and balanced growth (financial results, EdF's strategy in building a competitive global group: consolidating the European network, moving forward in energy-related services, responding to increasing energy demand in emerging countries); sustainable solutions for all (empowering the customer: competitive solutions for industrial customers, anticipating the needs of residential customers and SMEs, environmental solutions to enhance urban life, upgrading the network and providing access to energy; a sound, sustainable and secure energy mix: a highly competitive nuclear fleet, the vital resource of fossil-fuelled plants, a proactive approach to renewable energies); a global commitment to corporate social responsibility (human resources and partnerships). (J.S.)