WorldWideScience

Sample records for carlo neutron transport

  1. TRIPOLI-3: a neutron/photon Monte Carlo transport code

    Energy Technology Data Exchange (ETDEWEB)

    Nimal, J.C.; Vergnaud, T. [Commissariat a l' Energie Atomique, Gif-sur-Yvette (France). Service d' Etudes de Reacteurs et de Mathematiques Appliquees

    2001-07-01

    The present version of TRIPOLI-3 solves the transport equation for coupled neutron and gamma ray problems in three dimensional geometries by using the Monte Carlo method. This code is devoted both to shielding and criticality problems. The most important feature for particle transport equation solving is the fine treatment of the physical phenomena and sophisticated biasing technics useful for deep penetrations. The code is used either for shielding design studies or for reference and benchmark to validate cross sections. Neutronic studies are essentially cell or small core calculations and criticality problems. TRIPOLI-3 has been used as reference method, for example, for resonance self shielding qualification. (orig.)

  2. Guideline of Monte Carlo calculation. Neutron/gamma ray transport simulation by Monte Carlo method

    CERN Document Server

    2002-01-01

    This report condenses basic theories and advanced applications of neutron/gamma ray transport calculations in many fields of nuclear energy research. Chapters 1 through 5 treat historical progress of Monte Carlo methods, general issues of variance reduction technique, cross section libraries used in continuous energy Monte Carlo codes. In chapter 6, the following issues are discussed: fusion benchmark experiments, design of ITER, experiment analyses of fast critical assembly, core analyses of JMTR, simulation of pulsed neutron experiment, core analyses of HTTR, duct streaming calculations, bulk shielding calculations, neutron/gamma ray transport calculations of the Hiroshima atomic bomb. Chapters 8 and 9 treat function enhancements of MCNP and MVP codes, and a parallel processing of Monte Carlo calculation, respectively. An important references are attached at the end of this report.

  3. Neutron spectrum obtained with Monte Carlo and transport theory

    International Nuclear Information System (INIS)

    The development of the computer, resulting in increasing memory capacity and processing speed, has enabled the application of Monte Carlo method to estimate the fluxes in thousands of fine bin energy structure. Usually the MC calculation is made using continuous energy nuclear data and exact geometry. Self shielding and interference of nuclides resonances are properly considered. Therefore, the fluxes obtained by this method may be a good estimation of the neutron energy distribution (spectrum) for the problem. In an early work it was proposed to use these fluxes as weighting spectrum to generate multigroup cross section for fast reactor analysis using deterministic codes. This non-traditional use of MC calculation needs a validation to gain confidence in the results. The work presented here is the validation start step of this scheme. The spectra of the JOYO first core fuel assembly MK-I and the benchmark Godiva were calculated using the tally flux estimator of the MCNP code and compared with the reference. Also, the two problems were solved with the multigroup transport theory code XSDRN of the AMPX system using the 171 energy groups VITAMIN-C library. The spectra differences arising from the utilization of these codes, the influence of evaluated data file and the application to fast reactor calculation are discussed. (author)

  4. MCNP, a general Monte Carlo code for neutron and photon transport: a summary

    International Nuclear Information System (INIS)

    The general-purpose Monte Carlo code MCNP can be used for neutron, photon, or coupled neutron-photon transport, including the capability to calculate eigenvalues for critical systems. The code treats an arbitrary three-dimensional configuration of materials in geometric cells bounded by first- and second-degree surfaces and some special fourth-degree surfaces

  5. Subroutines to Simulate Fission Neutrons for Monte Carlo Transport Codes

    CERN Document Server

    Lestone, J P

    2014-01-01

    Fortran subroutines have been written to simulate the production of fission neutrons from the spontaneous fission of 252Cf and 240Pu, and from the thermal neutron induced fission of 239Pu and 235U. The names of these four subroutines are getnv252, getnv240, getnv239, and getnv235, respectively. These subroutines reproduce measured first, second, and third moments of the neutron multiplicity distributions, measured neutron-fission correlation data for the spontaneous fission of 252Cf, and measured neutron-neutron correlation data for both the spontaneous fission of 252Cf and the thermal neutron induced fission of 235U. The codes presented here can be used to study the possible uses of neutron-neutron correlations in the area of transparency measurements and the uses of neutron-neutron correlations in coincidence neutron imaging.

  6. A Monte Carlo Green's function method for three-dimensional neutron transport

    International Nuclear Information System (INIS)

    This paper describes a Monte Carlo transport kernel capability, which has recently been incorporated into the RACER continuous-energy Monte Carlo code. The kernels represent a Green's function method for neutron transport from a fixed-source volume out to a particular volume of interest. This method is very powerful transport technique. Also, since kernels are evaluated numerically by Monte Carlo, the problem geometry can be arbitrarily complex, yet exact. This method is intended for problems where an ex-core neutron response must be determined for a variety of reactor conditions. Two examples are ex-core neutron detector response and vessel critical weld fast flux. The response is expressed in terms of neutron transport kernels weighted by a core fission source distribution. In these types of calculations, the response must be computed for hundreds of source distributions, but the kernels only need to be calculated once. The advance described in this paper is that the kernels are generated with a highly accurate three-dimensional Monte Carlo transport calculation instead of an approximate method such as line-of-sight attenuation theory or a synthesized three-dimensional discrete ordinates solution

  7. Neutron cross-section probability tables in TRIPOLI-3 Monte Carlo transport code

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, S.H.; Vergnaud, T.; Nimal, J.C. [Commissariat a l`Energie Atomique, Gif-sur-Yvette (France). Lab. d`Etudes de Protection et de Probabilite

    1998-03-01

    Neutron transport calculations need an accurate treatment of cross sections. Two methods (multi-group and pointwise) are usually used. A third one, the probability table (PT) method, has been developed to produce a set of cross-section libraries, well adapted to describe the neutron interaction in the unresolved resonance energy range. Its advantage is to present properly the neutron cross-section fluctuation within a given energy group, allowing correct calculation of the self-shielding effect. Also, this PT cross-section representation is suitable for simulation of neutron propagation by the Monte Carlo method. The implementation of PTs in the TRIPOLI-3 three-dimensional general Monte Carlo transport code, developed at Commissariat a l`Energie Atomique, and several validation calculations are presented. The PT method is proved to be valid not only in the unresolved resonance range but also in all the other energy ranges.

  8. Subroutines to Simulate Fission Neutrons for Monte Carlo Transport Codes

    OpenAIRE

    Lestone, J. P.

    2014-01-01

    Fortran subroutines have been written to simulate the production of fission neutrons from the spontaneous fission of 252Cf and 240Pu, and from the thermal neutron induced fission of 239Pu and 235U. The names of these four subroutines are getnv252, getnv240, getnv239, and getnv235, respectively. These subroutines reproduce measured first, second, and third moments of the neutron multiplicity distributions, measured neutron-fission correlation data for the spontaneous fission of 252Cf, and meas...

  9. Monte Carlo method for neutron transport calculations in graphics processing units (GPUs)

    International Nuclear Information System (INIS)

    Monte Carlo simulation is well suited for solving the Boltzmann neutron transport equation in an inhomogeneous media for complicated geometries. However, routine applications require the computation time to be reduced to hours and even minutes in a desktop PC. The interest in adopting Graphics Processing Units (GPUs) for Monte Carlo acceleration is rapidly growing. This is due to the massive parallelism provided by the latest GPU technologies which is the most promising solution to the challenge of performing full-size reactor core analysis on a routine basis. In this study, Monte Carlo codes for a fixed-source neutron transport problem were developed for GPU environments in order to evaluate issues associated with computational speedup using GPUs. Results obtained in this work suggest that a speedup of several orders of magnitude is possible using the state-of-the-art GPU technologies. (author)

  10. Monte Carlo perturbation theory in neutron transport calculations

    International Nuclear Information System (INIS)

    The need to obtain sensitivities in complicated geometrical configurations has resulted in the development of Monte Carlo sensitivity estimation. A new method has been developed to calculate energy-dependent sensitivities of any number of responses in a single Monte Carlo calculation with a very small time penalty. This estimation typically increases the tracking time per source particle by about 30%. The method of estimation is explained. Sensitivities obtained are compared with those calculated by discrete ordinates methods. Further theoretical developments, such as second-order perturbation theory and application to k/sub eff/ calculations, are discussed. The application of the method to uncertainty analysis and to the analysis of benchmark experiments is illustrated. 5 figures

  11. Systems guide to MCNP (Monte Carlo Neutron and Photon Transport Code)

    International Nuclear Information System (INIS)

    The subject of this report is the implementation of the Los Alamos National Laboratory Monte Carlo Neutron and Photon Transport Code - Version 3 (MCNP) on the different types of computer systems, especially the IBM MVS system. The report supplements the documentation of the RSIC computer code package CCC-200/MCNP. Details of the procedure to follow in executing MCNP on the IBM computers, either in batch mode or interactive mode, are provided

  12. Modular, object-oriented redesign of a large-scale Monte Carlo neutron transport program

    International Nuclear Information System (INIS)

    This paper describes the modular, object-oriented redesign of a large-scale Monte Carlo neutron transport program. This effort represents a complete 'white sheet of paper' rewrite of the code. In this paper, the motivation driving this project, the design objectives for the new version of the program, and the design choices and their consequences will be discussed. The design itself will also be described, including the important subsystems as well as the key classes within those subsystems

  13. Description of a neutron field perturbed by a probe using coupled Monte Carlo and discrete ordinates radiation transport calculations

    International Nuclear Information System (INIS)

    This work concerns calculation of a neutron response, caused by a neutron field perturbed by materials surrounding the source or the detector. Solution of a problem is obtained using coupling of the Monte Carlo radiation transport computation for the perturbed region and the discrete ordinates transport computation for the unperturbed system. (author). 62 refs

  14. Snow shielding factors for cosmogenic nuclide dating inferred from Monte Carlo neutron transport simulations

    Science.gov (United States)

    Zweck, Christopher; Zreda, Marek; Desilets, Darin

    2013-10-01

    Conventional formulations of changes in cosmogenic nuclide production rates with snow cover are based on a mass-shielding approach, which neglects the role of neutron moderation by hydrogen. This approach can produce erroneous correction factors and add to the uncertainty of the calculated cosmogenic exposure ages. We use a Monte Carlo particle transport model to simulate fluxes of secondary cosmic-ray neutrons near the surface of the Earth and vary surface snow depth to show changes in neutron fluxes above rock or soil surface. To correspond with shielding factors for spallation and low-energy neutron capture, neutron fluxes are partitioned into high-energy, epithermal and thermal components. The results suggest that high-energy neutrons are attenuated by snow cover at a significantly higher rate (shorter attenuation length) than indicated by the commonly-used mass-shielding formulation. As thermal and epithermal neutrons derive from the moderation of high-energy neutrons, the presence of a strong moderator such as hydrogen in snow increases the thermal neutron flux both within the snow layer and above it. This means that low-energy production rates are affected by snow cover in a manner inconsistent with the mass-shielding approach and those formulations cannot be used to compute snow correction factors for nuclides produced by thermal neutrons. Additionally, as above-ground low-energy neutron fluxes vary with snow cover as a result of reduced diffusion from the ground, low-energy neutron fluxes are affected by snow even if the snow is at some distance from the site where measurements are made.

  15. A portable, parallel, object-oriented Monte Carlo neutron transport code in C++

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.R.; Cummings, J.C. [Los Alamos National Lab., NM (United States); Nolen, S.D. [Texas A and M Univ., College Station, TX (United States)]|[Los Alamos National Lab., NM (United States)

    1997-05-01

    We have developed a multi-group Monte Carlo neutron transport code using C++ and the Parallel Object-Oriented Methods and Applications (POOMA) class library. This transport code, called MC++, currently computes k and {alpha}-eigenvalues and is portable to and runs parallel on a wide variety of platforms, including MPPs, clustered SMPs, and individual workstations. It contains appropriate classes and abstractions for particle transport and, through the use of POOMA, for portable parallelism. Current capabilities of MC++ are discussed, along with physics and performance results on a variety of hardware, including all Accelerated Strategic Computing Initiative (ASCI) hardware. Current parallel performance indicates the ability to compute {alpha}-eigenvalues in seconds to minutes rather than hours to days. Future plans and the implementation of a general transport physics framework are also discussed.

  16. Domain decomposition and terabyte tallies with the OpenMC Monte Carlo neutron transport code

    International Nuclear Information System (INIS)

    Memory limitations are a key obstacle to applying Monte Carlo neutron transport methods to high-fidelity full-core reactor analysis. Billions of unique regions are needed to carry out full-core depletion and fuel performance analyses, equating to terabytes of memory for isotopic abundances and tally scores - far more than can fit on a single computational node in modern architectures. This work introduces an implementation of domain decomposition that addresses this problem, demonstrating excellent scaling up to a 2.39TB mesh-tally distributed across 512 compute nodes running a full-core reactor benchmark on the Mira Blue Gene/Q supercomputer at Argonne National Laboratory. (author)

  17. FOCUS, Neutron Transport System for Complex Geometry Reactor Core and Shielding Problems by Monte-Carlo

    International Nuclear Information System (INIS)

    1 - Description of problem or function: FOCUS enables the calculation of any quantity related to neutron transport in reactor or shielding problems, but was especially designed to calculate differential quantities, such as point values at one or more of the space, energy, direction and time variables of quantities like neutron flux, detector response, reaction rate, etc. or averages of such quantities over a small volume of the phase space. Different types of problems can be treated: systems with a fixed neutron source which may be a mono-directional source located out- side the system, and Eigen function problems in which the neutron source distribution is given by the (unknown) fundamental mode Eigen function distribution. Using Monte Carlo methods complex 3- dimensional geometries and detailed cross section information can be treated. Cross section data are derived from ENDF/B, with anisotropic scattering and discrete or continuous inelastic scattering taken into account. Energy is treated as a continuous variable and time dependence may also be included. 2 - Method of solution: A transformed form of the adjoint Boltzmann equation in integral representation is solved for the space, energy, direction and time variables by Monte Carlo methods. Adjoint particles are defined with properties in some respects contrary to those of neutrons. Adjoint particle histories are constructed from which estimates are obtained of the desired quantity. Adjoint cross sections are defined with which the nuclide and reaction type are selected in a collision. The energy after a collision is selected from adjoint energy distributions calculated together with the adjoint cross sections in advance of the actual Monte Carlo calculation. For multiplying systems successive generations of adjoint particles are obtained which will die out for subcritical systems with a fixed neutron source and will be kept approximately stationary for Eigen function problems. Completely arbitrary problems can

  18. MCNP: a general Monte Carlo code for neutron and photon transport

    International Nuclear Information System (INIS)

    The general-purpose Monte Carlo code MCNP ca be used for neutron, photon, or coupled neutron-photon transport, including the capability to calculate eigenvalues for critical systems. The code treats an arbitrary three-dimensional configuration of materials in geometric cells bounded by first- and second-degree surfaces and some special fourth-degree surfaces (elliptical tori). Pointwise cross-section data are used. For neutrons, all reactions given in a particular cross-section evaluation are accounted for. Thermal neutrons are described by both the free-gas and S(α,β) models. For photons, the code takes account of incoherent and coherent scattering, the possibility of fluorescent emission following photoelectric absorption, and absorption in pair production with local emission of annihilation radiation. MCNP includes an elaborate, interactive plotting capability that allows the user to view his input geometry to help check for setup errors. Standard features which are available to improve computational efficiency include geometry splitting and Russian roulette, weight cutoff with Russian roulette, correlated sampling, analog capture or capture by weight reduction, the exponential transformation, energy splitting, forced collisions in designated cells, flux estimates at point or ring detectors, deterministically transporting pseudo-particles to designated regions, track-length estimators, source biasing, and several parameter cutoffs. Extensive summary information is provided to help the user better understand the physics and Monte Carlo simulation of his problem. The standard, user-defined output of MCNP includes two-way current as a function of direction across any set of surfaces or surface segments in the problem. Flux across any set of surfaces or surface segments is available. 58 figures, 28 tables

  19. MCNP: a general Monte Carlo code for neutron and photon transport

    International Nuclear Information System (INIS)

    MCNP is a very general Monte Carlo neutron photon transport code system with approximately 250 person years of Group X-6 code development invested. It is extremely portable, user-oriented, and a true production code as it is used about 60 Cray hours per month by about 150 Los Alamos users. It has as its data base the best cross-section evaluations available. MCNP contains state-of-the-art traditional and adaptive Monte Carlo techniques to be applied to the solution of an ever-increasing number of problems. Excellent user-oriented documentation is available for all facets of the MCNP code system. Many useful and important variants of MCNP exist for special applications. The Radiation Shielding Information Center (RSIC) in Oak Ridge, Tennessee is the contact point for worldwide MCNP code and documentation distribution. A much improved MCNP Version 3A will be available in the fall of 1985, along with new and improved documentation. Future directions in MCNP development will change the meaning of MCNP to Monte Carlo N Particle where N particle varieties will be transported

  20. Improved Convergence Rate of Multi-Group Scattering Moment Tallies for Monte Carlo Neutron Transport Codes

    Science.gov (United States)

    Nelson, Adam

    Multi-group scattering moment matrices are critical to the solution of the multi-group form of the neutron transport equation, as they are responsible for describing the change in direction and energy of neutrons. These matrices, however, are difficult to correctly calculate from the measured nuclear data with both deterministic and stochastic methods. Calculating these parameters when using deterministic methods requires a set of assumptions which do not hold true in all conditions. These quantities can be calculated accurately with stochastic methods, however doing so is computationally expensive due to the poor efficiency of tallying scattering moment matrices. This work presents an improved method of obtaining multi-group scattering moment matrices from a Monte Carlo neutron transport code. This improved method of tallying the scattering moment matrices is based on recognizing that all of the outgoing particle information is known a priori and can be taken advantage of to increase the tallying efficiency (therefore reducing the uncertainty) of the stochastically integrated tallies. In this scheme, the complete outgoing probability distribution is tallied, supplying every one of the scattering moment matrices elements with its share of data. In addition to reducing the uncertainty, this method allows for the use of a track-length estimation process potentially offering even further improvement to the tallying efficiency. Unfortunately, to produce the needed distributions, the probability functions themselves must undergo an integration over the outgoing energy and scattering angle dimensions. This integration is too costly to perform during the Monte Carlo simulation itself and therefore must be performed in advance by way of a pre-processing code. The new method increases the information obtained from tally events and therefore has a significantly higher efficiency than the currently used techniques. The improved method has been implemented in a code system

  1. Modelling of neutron and photon transport in iron and concrete radiation shieldings by the Monte Carlo method - Version 2

    CERN Document Server

    Žukauskaite, A; Plukiene, R; Plukis, A

    2007-01-01

    Particle accelerators and other high energy facilities produce penetrating ionizing radiation (neutrons and γ-rays) that must be shielded. The objective of this work was to model photon and neutron transport in various materials, usually used as shielding, such as concrete, iron or graphite. Monte Carlo method allows obtaining answers by simulating individual particles and recording some aspects of their average behavior. In this work several nuclear experiments were modeled: AVF 65 – γ-ray beams (1-10 MeV), HIMAC and ISIS-800 – high energy neutrons (20-800 MeV) transport in iron and concrete. The results were then compared with experimental data.

  2. GPU-based high performance Monte Carlo simulation in neutron transport

    Energy Technology Data Exchange (ETDEWEB)

    Heimlich, Adino; Mol, Antonio C.A.; Pereira, Claudio M.N.A. [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Lab. de Inteligencia Artificial Aplicada], e-mail: cmnap@ien.gov.br

    2009-07-01

    Graphics Processing Units (GPU) are high performance co-processors intended, originally, to improve the use and quality of computer graphics applications. Since researchers and practitioners realized the potential of using GPU for general purpose, their application has been extended to other fields out of computer graphics scope. The main objective of this work is to evaluate the impact of using GPU in neutron transport simulation by Monte Carlo method. To accomplish that, GPU- and CPU-based (single and multicore) approaches were developed and applied to a simple, but time-consuming problem. Comparisons demonstrated that the GPU-based approach is about 15 times faster than a parallel 8-core CPU-based approach also developed in this work. (author)

  3. MONTE CARLO NEUTRINO TRANSPORT THROUGH REMNANT DISKS FROM NEUTRON STAR MERGERS

    Energy Technology Data Exchange (ETDEWEB)

    Richers, Sherwood; Ott, Christian D. [TAPIR, Mailcode 350-17, Walter Burke Institute for Theoretical Physics, California Institute of Technology, Pasadena, CA 91125 (United States); Kasen, Daniel; Fernández, Rodrigo [Department of Astronomy and Theoretical Astrophysics Center, University of California, Berkeley, CA 94720 (United States); O’Connor, Evan [Department of Physics, Campus Code 8202, North Carolina State University, Raleigh, NC 27695 (United States)

    2015-11-01

    We present Sedonu, a new open source, steady-state, special relativistic Monte Carlo (MC) neutrino transport code, available at bitbucket.org/srichers/sedonu. The code calculates the energy- and angle-dependent neutrino distribution function on fluid backgrounds of any number of spatial dimensions, calculates the rates of change of fluid internal energy and electron fraction, and solves for the equilibrium fluid temperature and electron fraction. We apply this method to snapshots from two-dimensional simulations of accretion disks left behind by binary neutron star mergers, varying the input physics and comparing to the results obtained with a leakage scheme for the cases of a central black hole and a central hypermassive neutron star. Neutrinos are guided away from the densest regions of the disk and escape preferentially around 45° from the equatorial plane. Neutrino heating is strengthened by MC transport a few scale heights above the disk midplane near the innermost stable circular orbit, potentially leading to a stronger neutrino-driven wind. Neutrino cooling in the dense midplane of the disk is stronger when using MC transport, leading to a globally higher cooling rate by a factor of a few and a larger leptonization rate by an order of magnitude. We calculate neutrino pair annihilation rates and estimate that an energy of 2.8 × 10{sup 46} erg is deposited within 45° of the symmetry axis over 300 ms when a central BH is present. Similarly, 1.9 × 10{sup 48} erg is deposited over 3 s when an HMNS sits at the center, but neither estimate is likely to be sufficient to drive a gamma-ray burst jet.

  4. TRIPOLI: a general Monte Carlo code, present state and future prospects. [Neutron and gamma ray transport

    Energy Technology Data Exchange (ETDEWEB)

    Nimal, J.C.; Vergnaud, T. (CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France))

    1990-01-01

    This paper describes the most important features of the Monte Carlo code TRIPOLI-2. This code solves the Boltzmann equation in three-dimensional geometries for coupled neutron and gamma rays problems. A particular emphasis is devoted to the biasing techniques, which are very important for deep penetration. Future developments in TRIPOLI are described in the conclusion. (author).

  5. Modeling of neutron and photon transport in iron and concrete radiation shields by using Monte Carlo method

    CERN Document Server

    Žukauskaitėa, A; Plukienė, R; Ridikas, D

    2007-01-01

    Particle accelerators and other high energy facilities produce penetrating ionizing radiation (neutrons and γ-rays) that must be shielded. The objective of this work was to model photon and neutron transport in various materials, usually used as shielding, such as concrete, iron or graphite. Monte Carlo method allows obtaining answers by simulating individual particles and recording some aspects of their average behavior. In this work several nuclear experiments were modeled: AVF 65 (AVF cyclotron of Research Center of Nuclear Physics, Osaka University, Japan) – γ-ray beams (1-10 MeV), HIMAC (heavy-ion synchrotron of the National Institute of Radiological Sciences in Chiba, Japan) and ISIS-800 (ISIS intensive spallation neutron source facility of the Rutherford Appleton laboratory, UK) – high energy neutron (20-800 MeV) transport in iron and concrete. The calculation results were then compared with experimental data.compared with experimental data.

  6. TRIPOLI capabilities proved by a set of solved problems. [Monte Carlo neutron and gamma ray transport code

    Energy Technology Data Exchange (ETDEWEB)

    Vergnaud, T.; Nimal, J.C. (CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France))

    1990-01-01

    The three-dimensional polycinetic Monte Carlo particle transport code TRIPOLI has been under development in the French Shielding Laboratory at Saclay since 1965. TRIPOLI-1 began to run in 1970 and became TRIPOLI-2 in 1978: since then its capabilities have been improved and many studies have been performed. TRIPOLI can treat stationary or time dependent problems in shielding and in neutronics. Some examples of solved problems are presented to demonstrate the many possibilities of the system. (author).

  7. Neutron secondary-particle production cross sections and their incorporation into Monte-Carlo transport codes

    International Nuclear Information System (INIS)

    Realistic simulations of the passage of fast neutrons through tissue require a large quantity of cross-sectional data. What are needed are differential (in particle type, energy and angle) cross sections. A computer code is described which produces such spectra for neutrons above ∼14 MeV incident on light nuclei such as carbon and oxygen. Comparisons have been made with experimental measurements of double-differential secondary charged-particle production on carbon and oxygen at energies from 27 to 60 MeV; they indicate that the model is adequate in this energy range. In order to utilize fully the results of these calculations, they should be incorporated into a neutron transport code. This requires defining a generalized format for describing charged-particle production, putting the calculated results in this format, interfacing the neutron transport code with these data, and charged-particle transport. The design and development of such a program is described. 13 refs., 3 figs

  8. The Development of WARP - A Framework for Continuous Energy Monte Carlo Neutron Transport in General 3D Geometries on GPUs

    Science.gov (United States)

    Bergmann, Ryan

    Graphics processing units, or GPUs, have gradually increased in computational power from the small, job-specific boards of the early 1990s to the programmable powerhouses of today. Compared to more common central processing units, or CPUs, GPUs have a higher aggregate memory bandwidth, much higher floating-point operations per second (FLOPS), and lower energy consumption per FLOP. Because one of the main obstacles in exascale computing is power consumption, many new supercomputing platforms are gaining much of their computational capacity by incorporating GPUs into their compute nodes. Since CPU-optimized parallel algorithms are not directly portable to GPU architectures (or at least not without losing substantial performance), transport codes need to be rewritten to execute efficiently on GPUs. Unless this is done, reactor simulations cannot take full advantage of these new supercomputers. WARP, which can stand for ``Weaving All the Random Particles,'' is a three-dimensional (3D) continuous energy Monte Carlo neutron transport code developed in this work as to efficiently implement a continuous energy Monte Carlo neutron transport algorithm on a GPU. WARP accelerates Monte Carlo simulations while preserving the benefits of using the Monte Carlo Method, namely, very few physical and geometrical simplifications. WARP is able to calculate multiplication factors, flux tallies, and fission source distributions for time-independent problems, and can run in both criticality or fixed source modes. WARP can transport neutrons in unrestricted arrangements of parallelepipeds, hexagonal prisms, cylinders, and spheres. WARP uses an event-based algorithm, but with some important differences. Moving data is expensive, so WARP uses a remapping vector of pointer/index pairs to direct GPU threads to the data they need to access. The remapping vector is sorted by reaction type after every transport iteration using a high-efficiency parallel radix sort, which serves to keep the

  9. Monte Carlo transport simulation for a long counter neutron detector employed as a cosmic rays induced neutron monitor at ground level

    Energy Technology Data Exchange (ETDEWEB)

    Pazianotto, Mauricio Tizziani; Carlson, Brett Vern [Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil); Federico, Claudio Antonio; Goncalez, Odair Lelis [Centro Tecnico Aeroespacial (CTA), Sao Jose dos Campos, SP (Brazil). Instituto de Estudos Avancados

    2011-07-01

    Full text: Great effort is required to understand better the cosmic radiation (CR) dose received by sensitive equipment, on-board computers and aircraft crew members at Brazil airspace, because there is a large area of South America and Brazil subject to the South Atlantic Anomaly (SAA). High energy neutrons are produced by interactions between primary cosmic ray and atmospheric atoms, and also undergo moderation resulting in a wider spectrum of energy ranging from thermal energies (0:025eV ) to energies of several hundreds of MeV. Measurements of the cosmic radiation dose on-board aircrafts need to be followed with an integral flow monitor on the ground level in order to register CR intensity variations during the measurements. The Long Counter (LC) neutron detector was designed as a directional neutron flux meter standard because it presents fairly constant response for energy under 10MeV. However we would like to use it as a ground based neutron monitor for cosmic ray induced neutron spectrum (CRINS) that presents an isotropic fluency and a wider spectrum of energy. The LC was modeled and tested using a Monte Carlo transport simulation for irradiations with known neutron sources ({sup 241}Am-Be and {sup 251}Cf) as a benchmark. Using this geometric model its efficiency was calculated to CRINS isotropic flux, introducing high energy neutron interactions models. The objective of this work is to present the model for simulation of the isotropic neutron source employing the MCNPX code (Monte Carlo N-Particle eXtended) and then access the LC efficiency to compare it with experimental results for cosmic ray neutrons measures on ground level. (author)

  10. Users Manual for TART 2002: A Coupled Neutron-Photon 3-D, Combinatorial Geometry Time Dependent Monte Carlo Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    Cullen, D E

    2003-06-06

    TART 2002 is a coupled neutron-photon, 3 Dimensional, combinatorial geometry, time dependent Monte Carlo radiation transport code. This code can run on any modern computer. It is a complete system to assist you with input preparation, running Monte Carlo calculations, and analysis of output results. TART 2002 is also incredibly FAST; if you have used similar codes, you will be amazed at how fast this code is compared to other similar codes. Use of the entire system can save you a great deal of time and energy. TART 2002 is distributed on CD. This CD contains on-line documentation for all codes included in the system, the codes configured to run on a variety of computers, and many example problems that you can use to familiarize yourself with the system. TART 2002 completely supersedes all older versions of TART, and it is strongly recommended that users only use the most recent version of TART 2002 and its data files.

  11. TART 2000: A Coupled Neutron-Photon, 3-D, Combinatorial Geometry, Time Dependent, Monte Carlo Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    Cullen, D.E

    2000-11-22

    TART2000 is a coupled neutron-photon, 3 Dimensional, combinatorial geometry, time dependent Monte Carlo radiation transport code. This code can run on any modern computer. It is a complete system to assist you with input Preparation, running Monte Carlo calculations, and analysis of output results. TART2000 is also incredibly FAST; if you have used similar codes, you will be amazed at how fast this code is compared to other similar codes. Use of the entire system can save you a great deal of time and energy. TART2000 is distributed on CD. This CD contains on-line documentation for all codes included in the system, the codes configured to run on a variety of computers, and many example problems that you can use to familiarize yourself with the system. TART2000 completely supersedes all older versions of TART, and it is strongly recommended that users only use the most recent version of TART2000 and its data files.

  12. Direct utilization of information from nuclear data files in Monte Carlo simulation of neutron and photon transport

    International Nuclear Information System (INIS)

    Questions, related to Monte-Carlo method for solution of neutron and photon transport equation, are discussed in the work concerned. Problems dealing with direct utilization of information from evaluated nuclear data files in run-time calculations are considered. ENDF-6 format libraries have been used for calculations. Approaches provided by the rules of ENDF-6 files 2, 3-6, 12-15, 23, 27 and algorithms for reconstruction of resolved and unresolved resonance region cross sections under preset energy are described. The comparison results of calculations made by NJOY and GRUCON programs and computed cross sections data are represented. Test computation data of neutron leakage spectra for spherical benchmark-experiments are also represented. (authors)

  13. McSUB, a Monte Carlo Library for neutron transport in two different media for the neutron energy range 0.1-20 MeV

    International Nuclear Information System (INIS)

    Library McSUB is a package of easy-to-use subroutines and functions treating neutron transport in two different kind of media by Monte Carlo calculations. The first medium, D0, contains deuterium and natural carbon while the second medium, D1, contains hydrogen and natural carbon. In the neutron energy interval 0.1-20 MeV eight different kinds of interactions are considered: Elastic and (n,2n) interactions with deuterium, elastic interactions with hydrogen and elastic and inelastic interactions with natural carbon. The inelastic interaction with carbon are subdivided into four different interaction classes, one for each excited state of the recoiled carbon nucleus. The neutron cross sections and Legendre coefficients (expressing differential cross sections) have been supplied by NEA Data Bank in France. (author)

  14. Thermal Scattering Law Data: Implementation and Testing Using the Monte Carlo Neutron Transport Codes COG, MCNP and TART

    Energy Technology Data Exchange (ETDEWEB)

    Cullen, D E; Hansen, L F; Lent, E M; Plechaty, E F

    2003-05-17

    Recently we implemented the ENDF/B-VI thermal scattering law data in our neutron transport codes COG and TART. Our objective was to convert the existing ENDF/B data into double differential form in the Livermore ENDL format. This will allow us to use the ENDF/B data in any neutron transport code, be it a Monte Carlo, or deterministic code. This was approached as a multi-step project. The first step was to develop methods to directly use the thermal scattering law data in our Monte Carlo codes. The next step was to convert the data to double-differential form. The last step was to verify that the results obtained using the data directly are essentially the same as the results obtained using the double differential data. Part of the planned verification was intended to insure that the data as finally implemented in the COG and TART codes, gave the same answer as the well known MCNP code, which includes thermal scattering law data. Limitations in the treatment of thermal scattering law data in MCNP have been uncovered that prevented us from performing this part of our verification.

  15. ACCELERATING FUSION REACTOR NEUTRONICS MODELING BY AUTOMATIC COUPLING OF HYBRID MONTE CARLO/DETERMINISTIC TRANSPORT ON CAD GEOMETRY

    Energy Technology Data Exchange (ETDEWEB)

    Biondo, Elliott D [ORNL; Ibrahim, Ahmad M [ORNL; Mosher, Scott W [ORNL; Grove, Robert E [ORNL

    2015-01-01

    Detailed radiation transport calculations are necessary for many aspects of the design of fusion energy systems (FES) such as ensuring occupational safety, assessing the activation of system components for waste disposal, and maintaining cryogenic temperatures within superconducting magnets. Hybrid Monte Carlo (MC)/deterministic techniques are necessary for this analysis because FES are large, heavily shielded, and contain streaming paths that can only be resolved with MC. The tremendous complexity of FES necessitates the use of CAD geometry for design and analysis. Previous ITER analysis has required the translation of CAD geometry to MCNP5 form in order to use the AutomateD VAriaNce reducTion Generator (ADVANTG) for hybrid MC/deterministic transport. In this work, ADVANTG was modified to support CAD geometry, allowing hybrid (MC)/deterministic transport to be done automatically and eliminating the need for this translation step. This was done by adding a new ray tracing routine to ADVANTG for CAD geometries using the Direct Accelerated Geometry Monte Carlo (DAGMC) software library. This new capability is demonstrated with a prompt dose rate calculation for an ITER computational benchmark problem using both the Consistent Adjoint Driven Importance Sampling (CADIS) method an the Forward Weighted (FW)-CADIS method. The variance reduction parameters produced by ADVANTG are shown to be the same using CAD geometry and standard MCNP5 geometry. Significant speedups were observed for both neutrons (as high as a factor of 7.1) and photons (as high as a factor of 59.6).

  16. Algorithmic choices in WARP – A framework for continuous energy Monte Carlo neutron transport in general 3D geometries on GPUs

    International Nuclear Information System (INIS)

    Highlights: • WARP, a GPU-accelerated Monte Carlo neutron transport code, has been developed. • The NVIDIA OptiX high-performance ray tracing library is used to process geometric data. • The unionized cross section representation is modified for higher performance. • Reference remapping is used to keep the GPU busy as neutron batch population reduces. • Reference remapping is done using a key-value radix sort on neutron reaction type. - Abstract: In recent supercomputers, general purpose graphics processing units (GPGPUs) are a significant faction of the supercomputer’s total computational power. GPGPUs have different architectures compared to central processing units (CPUs), and for Monte Carlo neutron transport codes used in nuclear engineering to take advantage of these coprocessor cards, transport algorithms must be changed to execute efficiently on them. WARP is a continuous energy Monte Carlo neutron transport code that has been written to do this. The main thrust of WARP is to adapt previous event-based transport algorithms to the new GPU hardware; the algorithmic choices for all parts of which are presented in this paper. It is found that remapping history data references increases the GPU processing rate when histories start to complete. The main reason for this is that completed data are eliminated from the address space, threads are kept busy, and memory bandwidth is not wasted on checking completed data. Remapping also allows the interaction kernels to be launched concurrently, improving efficiency. The OptiX ray tracing framework and CUDPP library are used for geometry representation and parallel dataset-side operations, ensuring high performance and reliability

  17. Development and Implementation of Photonuclear Cross-Section Data for Mutually Coupled Neutron-Photon Transport Calculations in the Monte Carlo N-Particle (MCNP) Radiation Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    Morgan C. White

    2000-07-01

    The fundamental motivation for the research presented in this dissertation was the need to development a more accurate prediction method for characterization of mixed radiation fields around medical electron accelerators (MEAs). Specifically, a model is developed for simulation of neutron and other particle production from photonuclear reactions and incorporated in the Monte Carlo N-Particle (MCNP) radiation transport code. This extension of the capability within the MCNP code provides for the more accurate assessment of the mixed radiation fields. The Nuclear Theory and Applications group of the Los Alamos National Laboratory has recently provided first-of-a-kind evaluated photonuclear data for a select group of isotopes. These data provide the reaction probabilities as functions of incident photon energy with angular and energy distribution information for all reaction products. The availability of these data is the cornerstone of the new methodology for state-of-the-art mutually coupled photon-neutron transport simulations. The dissertation includes details of the model development and implementation necessary to use the new photonuclear data within MCNP simulations. A new data format has been developed to include tabular photonuclear data. Data are processed from the Evaluated Nuclear Data Format (ENDF) to the new class ''u'' A Compact ENDF (ACE) format using a standalone processing code. MCNP modifications have been completed to enable Monte Carlo sampling of photonuclear reactions. Note that both neutron and gamma production are included in the present model. The new capability has been subjected to extensive verification and validation (V&V) testing. Verification testing has established the expected basic functionality. Two validation projects were undertaken. First, comparisons were made to benchmark data from literature. These calculations demonstrate the accuracy of the new data and transport routines to better than 25 percent. Second

  18. Development and Implementation of Photonuclear Cross-Section Data for Mutually Coupled Neutron-Photon Transport Calculations in the Monte Carlo N-Particle (MCNP) Radiation Transport Code

    International Nuclear Information System (INIS)

    The fundamental motivation for the research presented in this dissertation was the need to development a more accurate prediction method for characterization of mixed radiation fields around medical electron accelerators (MEAs). Specifically, a model is developed for simulation of neutron and other particle production from photonuclear reactions and incorporated in the Monte Carlo N-Particle (MCNP) radiation transport code. This extension of the capability within the MCNP code provides for the more accurate assessment of the mixed radiation fields. The Nuclear Theory and Applications group of the Los Alamos National Laboratory has recently provided first-of-a-kind evaluated photonuclear data for a select group of isotopes. These data provide the reaction probabilities as functions of incident photon energy with angular and energy distribution information for all reaction products. The availability of these data is the cornerstone of the new methodology for state-of-the-art mutually coupled photon-neutron transport simulations. The dissertation includes details of the model development and implementation necessary to use the new photonuclear data within MCNP simulations. A new data format has been developed to include tabular photonuclear data. Data are processed from the Evaluated Nuclear Data Format (ENDF) to the new class ''u'' A Compact ENDF (ACE) format using a standalone processing code. MCNP modifications have been completed to enable Monte Carlo sampling of photonuclear reactions. Note that both neutron and gamma production are included in the present model. The new capability has been subjected to extensive verification and validation (V and V) testing. Verification testing has established the expected basic functionality. Two validation projects were undertaken. First, comparisons were made to benchmark data from literature. These calculations demonstrate the accuracy of the new data and transport routines to better than 25 percent. Second, the ability to

  19. Analysis of the neutrons dispersion in a semi-infinite medium based in transport theory and the Monte Carlo method; Analisis de la dispersion de neutrones en un medio semi-infinito en base a teoria de transporte y el metodo de Monte Carlo

    Energy Technology Data Exchange (ETDEWEB)

    Arreola V, G. [IPN, Escuela Superior de Fisica y Matematicas, Posgrado en Ciencias Fisicomatematicas, area en Ingenieria Nuclear, Unidad Profesional Adolfo Lopez Mateos, Edificio 9, Col. San Pedro Zacatenco, 07730 Mexico D. F. (Mexico); Vazquez R, R.; Guzman A, J. R., E-mail: energia.arreola.uam@gmail.com [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Area de Ingenieria en Recursos Energeticos, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (Mexico)

    2012-10-15

    In this work a comparative analysis of the results for the neutrons dispersion in a not multiplicative semi-infinite medium is presented. One of the frontiers of this medium is located in the origin of coordinates, where a neutrons source in beam form, i.e., {mu}{omicron}=1 is also. The neutrons dispersion is studied on the statistical method of Monte Carlo and through the unidimensional transport theory and for an energy group. The application of transport theory gives a semi-analytic solution for this problem while the statistical solution for the flow was obtained applying the MCNPX code. The dispersion in light water and heavy water was studied. A first remarkable result is that both methods locate the maximum of the neutrons distribution to less than two mean free trajectories of transport for heavy water, while for the light water is less than ten mean free trajectories of transport; the differences between both methods is major for the light water case. A second remarkable result is that the tendency of both distributions is similar in small mean free trajectories, while in big mean free trajectories the transport theory spreads to an asymptote value and the solution in base statistical method spreads to zero. The existence of a neutron current of low energy and toward the source is demonstrated, in contrary sense to the neutron current of high energy coming from the own source. (Author)

  20. Evaluation of the response of a neutron detector of the Long-Counter type using a Monte Carlo transport simulation

    Energy Technology Data Exchange (ETDEWEB)

    Pazianotto, Mauricio Tizziani; Goncalez, Odair Lelis; Federico, Claudio Antonio [Centro Tecnico Aeroespacial (IEAv/CTA), Sao Jose dos Campos, SP (Brazil). Inst. de Estudos Avancados; Carlson, Brett Vern [Centro Tecnico Aeroespacial (ITA/CTA), Sao Jose dos Campos, SP (Brazil). Inst. Tecnologico de Aeronautica

    2010-07-01

    Full text: The Institute for Advanced Studies (IEAv) is developing activities to study the dose levels of ionizing radiation from cosmic rays (CR) received by aircraft crews, sensitive equipment (on-board computers, for example) and embedded electronics in Brazilian airspace. Neutrons generated by the interaction of CR with the atmosphere are the dominant particles in the dose accumulation in electronic circuits and aircraft crews at flight altitude. Their production has a very broad energy spectrum, ranging from thermal neutrons (0.025eV ) to neutrons of several hundreds of MeV , making their detection a very difficult process. To observe the temporal variation in flow during the measurements, a detector of the Long Counter (LC) type is being used. This detector is designed to measure the one-way flow of neutrons with constant response over a wide energy range (thermal to 20 MeV ). However, to measure cosmic rays, the flow of which is non-directional, the dependence of the response on the angle of incidence, as well as energy, should be properly investigated. The objective of this study is to assess the angular response of the neutron detector (Long Counter) using the code MCNP5 (Monte Carlo N-Particle) and to compare it with the experimental data previously obtained with a {sup 241}Am-Be source at a distance of 1.66 m from the geometric center of the detector, varying the angle of incidence from 00 to 3600 in intervals of 150. The simulation was performed by modeling in detail the structure and materials of the LC, as well as the experimental arrangement for irradiation. The results of the simulation present reasonable agreement with the experimental data. This agreement shows that the modeling of the geometry of the source-detector system is adequate. The next step is to develop a model of neutron detection for the higher energy present in cosmic radiation fields, for which the experimental calibration is not so easily achievable. (author)

  1. Monte Carlo method in radiation transport problems

    International Nuclear Information System (INIS)

    In neutral radiation transport problems (neutrons, photons), two values are important: the flux in the phase space and the density of particles. To solve the problem with Monte Carlo method leads to, among other things, build a statistical process (called the play) and to provide a numerical value to a variable x (this attribution is called score). Sampling techniques are presented. Play biasing necessity is proved. A biased simulation is made. At last, the current developments (rewriting of programs for instance) are presented due to several reasons: two of them are the vectorial calculation apparition and the photon and neutron transport in vacancy media

  2. 脉冲中子-裂变中子探测铀黄饼的MCNP模拟%The Monte Carlo N particle transport code simulation of pulsed neutron-fission neutron uranium yellowcake exploration

    Institute of Scientific and Technical Information of China (English)

    张坤明; 张雄杰; 瞿金辉; 汤彬

    2015-01-01

    利用MCNP程序模拟研究脉冲中子-裂变中子探测铀黄饼,采用脉冲式中子源,利用氦三管中子探测器记录裂变中子,得到铀黄饼中的铀含量信息。通过对14 MeV脉冲中子源和产生的裂变中子在不同铀含量模型中的输运计算,分析了裂变中子与铀含量的关系。结果表明:利用裂变超热中子衰减时间谱,可以确定铀黄饼中的铀含量;通过对热中子衰减时间谱进行校正,可以提高铀黄饼中铀含量计算结果的准确度。%The Monte Carlo N particle transport code ( MCNP ) is used to simulate how to explore the uranium yel⁃lowcake by using the pulsed neutron⁃fission neutron ( PNFN) method. In order to obtain uranium yellowcake quan⁃titation, pulsed neutron source was used, prompt fission neutrons were detected by using the neutron detector. Un⁃der the condition of different uranium quantitation models, the transport of the 14 MeV pulsed neutron source and the released fission neutron were calculated. On the basis of these, the relationship between fission neutron and ura⁃nium quantitation was studied. The results show that using the epithermal neutron time decay spectrum, the urani⁃um yellowcake quantitation can be determined; the precision of the uranium yellowcake quantitation could be in⁃creased by the correction of thermal neutron time decay spectrum.

  3. Monte Carlo simulations for optimization of neutron shielding concrete

    Science.gov (United States)

    Piotrowski, Tomasz; Tefelski, Dariusz; Polański, Aleksander; Skubalski, Janusz

    2012-06-01

    Concrete is one of the main materials used for gamma and neutron shielding. While in case of gamma rays an increase in density is usually efficient enough, protection against neutrons is more complex. The aim of this paper is to show the possibility of using the Monte Carlo codes for evaluation and optimization of concrete mix to reach better neutron shielding. Two codes (MCNPX and SPOT — written by authors) were used to simulate neutron transport through a wall made of different concretes. It is showed that concrete of higher compressive strength attenuates neutrons more effectively. The advantage of heavyweight concrete (with barite aggregate), usually used for gamma shielding, over the ordinary concrete was not so clear. Neutron shielding depends on many factors e.g. neutron energy, barrier thickness and atomic composition. All this makes a proper design of concrete as a very important issue for nuclear power plant safety assurance.

  4. 3D Monte-Carlo transport calculations of whole slab reactor cores: validation of deterministic neutronic calculation routes

    Energy Technology Data Exchange (ETDEWEB)

    Palau, J.M. [CEA Cadarache, Service de Physique des Reacteurs et du Cycle, Lab. de Projets Nucleaires, 13 - Saint-Paul-lez-Durance (France)

    2005-07-01

    This paper presents how Monte-Carlo calculations (French TRIPOLI4 poly-kinetic code with an appropriate pre-processing and post-processing software called OVNI) are used in the case of 3-dimensional heterogeneous benchmarks (slab reactor cores) to reduce model biases and enable a thorough and detailed analysis of the performances of deterministic methods and their associated data libraries with respect to key neutron parameters (reactivity, local power). Outstanding examples of application of these tools are presented regarding the new numerical methods implemented in the French lattice code APOLLO2 (advanced self-shielding models, new IDT characteristics method implemented within the discrete-ordinates flux solver model) and the JEFF3.1 nuclear data library (checked against JEF2.2 previous file). In particular we have pointed out, by performing multigroup/point-wise TRIPOLI4 (assembly and core) calculations, the efficiency (in terms of accuracy and computation time) of the new IDT method developed in APOLLO2. In addition, by performing 3-dimensional TRIPOLI4 calculations of the whole slab core (few millions of elementary volumes), the high quality of the new JEFF3.1 nuclear data files and revised evaluations (U{sup 235}, U{sup 238}, Hf) for reactivity prediction of slab cores critical experiments has been stressed. As a feedback of the whole validation process, improvements in terms of nuclear data (mainly Hf capture cross-sections) and numerical methods (advanced quadrature formulas accounting validation results, validation of new self-shielding models, parallelization) are suggested to improve even more the APOLLO2-CRONOS2 standard calculation route. (author)

  5. 3D Monte-Carlo transport calculations of whole slab reactor cores: validation of deterministic neutronic calculation routes

    International Nuclear Information System (INIS)

    This paper presents how Monte-Carlo calculations (French TRIPOLI4 poly-kinetic code with an appropriate pre-processing and post-processing software called OVNI) are used in the case of 3-dimensional heterogeneous benchmarks (slab reactor cores) to reduce model biases and enable a thorough and detailed analysis of the performances of deterministic methods and their associated data libraries with respect to key neutron parameters (reactivity, local power). Outstanding examples of application of these tools are presented regarding the new numerical methods implemented in the French lattice code APOLLO2 (advanced self-shielding models, new IDT characteristics method implemented within the discrete-ordinates flux solver model) and the JEFF3.1 nuclear data library (checked against JEF2.2 previous file). In particular we have pointed out, by performing multigroup/point-wise TRIPOLI4 (assembly and core) calculations, the efficiency (in terms of accuracy and computation time) of the new IDT method developed in APOLLO2. In addition, by performing 3-dimensional TRIPOLI4 calculations of the whole slab core (few millions of elementary volumes), the high quality of the new JEFF3.1 nuclear data files and revised evaluations (U235, U238, Hf) for reactivity prediction of slab cores critical experiments has been stressed. As a feedback of the whole validation process, improvements in terms of nuclear data (mainly Hf capture cross-sections) and numerical methods (advanced quadrature formulas accounting validation results, validation of new self-shielding models, parallelization) are suggested to improve even more the APOLLO2-CRONOS2 standard calculation route. (author)

  6. Monte-Carlo simulations of elastically backscattered neutrons from hidden explosives using three different neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    ElAgib, I. [College of Science, King Saud University, P.O. Box 2455 (Saudi Arabia)], E-mail: elagib@ksu.edu.sa; Elsheikh, N. [College of Applied and Industrial Science, University of Juba, Khartoum, P.O. Box 321 (Sudan); AlSewaidan, H. [College of Science, King Saud University, P.O. Box 2455 (Saudi Arabia); Habbani, F. [Faculty of Science, Physics Department, University of Khartoum, Khartoum, P.O. Box 321 (Sudan)

    2009-01-15

    Calculations of elastically backscattered (EBS) neutrons from hidden explosives buried in soil were performed using Monte-Carlo N-particle transport code MCNP5. Three different neutron sources were used in the study. The study re-examines the performance of the neutron backscattering methods in providing identification of hidden explosives through their chemical composition. The EBS neutron energy spectra of fast and slow neutrons of the major constituent elements in soil and an explosive material in form of TNT have shown definite structures that can be used for the identification of a buried landmine.

  7. Condensation and homogenization of cross sections for the deterministic transport codes with Monte Carlo method: Application to the GEN IV fast neutron reactors

    International Nuclear Information System (INIS)

    In the framework of the Generation IV reactors neutronic research, new core calculation tools are implemented in the code system APOLLO3 for the deterministic part. These calculation methods are based on the discretization concept of nuclear energy data (named multi-group and are generally produced by deterministic codes) and should be validated and qualified with respect to some Monte-Carlo reference calculations. This thesis aims to develop an alternative technique of producing multi-group nuclear properties by a Monte-Carlo code (TRIPOLI-4). At first, after having tested the existing homogenization and condensation functionalities with better precision obtained nowadays, some inconsistencies are revealed. Several new multi-group parameters estimators are developed and validated for TRIPOLI-4 code with the aid of itself, since it has the possibility to use the multi-group constants in a core calculation. Secondly, the scattering anisotropy effect which is necessary for handling neutron leakage case is studied. A correction technique concerning the diagonal line of the first order moment of the scattering matrix is proposed. This is named the IGSC technique and is based on the usage of an approximate current which is introduced by Todorova. An improvement of this IGSC technique is then presented for the geometries which hold an important heterogeneity property. This improvement uses a more accurate current quantity which is the projection on the abscissa X. The later current can represent the real situation better but is limited to 1D geometries. Finally, a B1 leakage model is implemented in the TRIPOLI-4 code for generating multi-group cross sections with a fundamental mode based critical spectrum. This leakage model is analyzed and validated rigorously by the comparison with other codes: Serpent and ECCO, as well as an analytical case.The whole development work introduced in TRIPOLI-4 code allows producing multi-group constants which can then be used in the core

  8. Calibration and Monte Carlo modelling of neutron long counters

    CERN Document Server

    Tagziria, H

    2000-01-01

    The Monte Carlo technique has become a very powerful tool in radiation transport as full advantage is taken of enhanced cross-section data, more powerful computers and statistical techniques, together with better characterisation of neutron and photon source spectra. At the National Physical Laboratory, calculations using the Monte Carlo radiation transport code MCNP-4B have been combined with accurate measurements to characterise two long counters routinely used to standardise monoenergetic neutron fields. New and more accurate response function curves have been produced for both long counters. A novel approach using Monte Carlo methods has been developed, validated and used to model the response function of the counters and determine more accurately their effective centres, which have always been difficult to establish experimentally. Calculations and measurements agree well, especially for the De Pangher long counter for which details of the design and constructional material are well known. The sensitivit...

  9. Monte Carlo simulation of neutron scattering instruments

    International Nuclear Information System (INIS)

    A library of Monte Carlo subroutines has been developed for the purpose of design of neutron scattering instruments. Using small-angle scattering as an example, the philosophy and structure of the library are described and the programs are used to compare instruments at continuous wave (CW) and long-pulse spallation source (LPSS) neutron facilities. The Monte Carlo results give a count-rate gain of a factor between 2 and 4 using time-of-flight analysis. This is comparable to scaling arguments based on the ratio of wavelength bandwidth to resolution width

  10. Coupled neutron transport for HZETRN

    Energy Technology Data Exchange (ETDEWEB)

    Slaba, T.C., E-mail: Tony.C.Slaba@nasa.go [Old Dominion University, Norfolk, VA 23505 (United States); Blattnig, S.R. [NASA Langley Research Center, Hampton, VA 23681 (United States); Aghara, S.K. [Prairie View A and M University, Prairie View, TX 77446 (United States); Townsend, L.W.; Handler, T. [University of Tennessee, Knoxville, TN 37996 (United States); Gabriel, T.A. [Scientific Investigation and Development, Knoxville, TN 37922 (United States); Pinsky, L.S.; Reddell, B. [University of Houston, Houston, TX 77204 (United States)

    2010-02-15

    Exposure estimates inside space vehicles, surface habitats, and high altitude aircrafts exposed to space radiation are highly influenced by secondary neutron production. The deterministic transport code HZETRN has been identified as a reliable and efficient tool for such studies, but improvements to the underlying transport models and numerical methods are still necessary. In this paper, the forward-backward (FB) and directionally coupled forward-backward (DC) neutron transport models are derived, numerical methods for the FB model are reviewed, and a computationally efficient numerical solution is presented for the DC model. Both models are compared to the Monte Carlo codes HETC-HEDS, FLUKA, and MCNPX, and the DC model is shown to agree closely with the Monte Carlo results. Finally, it is found in the development of either model that the decoupling of low energy neutrons from the light ion transport procedure adversely affects low energy light ion fluence spectra and exposure quantities. A first order correction is presented to resolve the problem, and it is shown to be both accurate and efficient.

  11. Coupled Neutron Transport for HZETRN

    Science.gov (United States)

    Slaba, Tony C.; Blattnig, Steve R.

    2009-01-01

    Exposure estimates inside space vehicles, surface habitats, and high altitude aircrafts exposed to space radiation are highly influenced by secondary neutron production. The deterministic transport code HZETRN has been identified as a reliable and efficient tool for such studies, but improvements to the underlying transport models and numerical methods are still necessary. In this paper, the forward-backward (FB) and directionally coupled forward-backward (DC) neutron transport models are derived, numerical methods for the FB model are reviewed, and a computationally efficient numerical solution is presented for the DC model. Both models are compared to the Monte Carlo codes HETC-HEDS, FLUKA, and MCNPX, and the DC model is shown to agree closely with the Monte Carlo results. Finally, it is found in the development of either model that the decoupling of low energy neutrons from the light particle transport procedure adversely affects low energy light ion fluence spectra and exposure quantities. A first order correction is presented to resolve the problem, and it is shown to be both accurate and efficient.

  12. THE MCNPX MONTE CARLO RADIATION TRANSPORT CODE

    Energy Technology Data Exchange (ETDEWEB)

    WATERS, LAURIE S. [Los Alamos National Laboratory; MCKINNEY, GREGG W. [Los Alamos National Laboratory; DURKEE, JOE W. [Los Alamos National Laboratory; FENSIN, MICHAEL L. [Los Alamos National Laboratory; JAMES, MICHAEL R. [Los Alamos National Laboratory; JOHNS, RUSSELL C. [Los Alamos National Laboratory; PELOWITZ, DENISE B. [Los Alamos National Laboratory

    2007-01-10

    MCNPX (Monte Carlo N-Particle eXtended) is a general-purpose Monte Carlo radiation transport code with three-dimensional geometry and continuous-energy transport of 34 particles and light ions. It contains flexible source and tally options, interactive graphics, and support for both sequential and multi-processing computer platforms. MCNPX is based on MCNP4B, and has been upgraded to most MCNP5 capabilities. MCNP is a highly stable code tracking neutrons, photons and electrons, and using evaluated nuclear data libraries for low-energy interaction probabilities. MCNPX has extended this base to a comprehensive set of particles and light ions, with heavy ion transport in development. Models have been included to calculate interaction probabilities when libraries are not available. Recent additions focus on the time evolution of residual nuclei decay, allowing calculation of transmutation and delayed particle emission. MCNPX is now a code of great dynamic range, and the excellent neutronics capabilities allow new opportunities to simulate devices of interest to experimental particle physics; particularly calorimetry. This paper describes the capabilities of the current MCNPX version 2.6.C, and also discusses ongoing code development.

  13. Monte Carlo Simulations of Neutron Oil well Logging Tools

    International Nuclear Information System (INIS)

    Monte Carlo simulations of simple neutron oil well logging tools into typical geological formations are presented.The simulated tools consist of both 14 MeV pulsed and continuous Am-Be neutron sources with time gated and continuous gamma ray detectors respectively.The geological formation consists of pure limestone with 15% absolute porosity in a wide range of oil saturation.The particle transport was performed with the Monte Carlo N-Particle Transport Code System, MCNP-4B.Several gamma ray spectra were obtained at the detector position that allow to perform composition analysis of the formation.In particular, the ratio C/O was analyzed as an indicator of oil saturation.Further calculations are proposed to simulate actual detector responses in order to contribute to understand the relation between the detector response with the formation composition

  14. Monte Carlo Simulations of Neutron Oil well Logging Tools

    CERN Document Server

    Azcurra, M

    2002-01-01

    Monte Carlo simulations of simple neutron oil well logging tools into typical geological formations are presented.The simulated tools consist of both 14 MeV pulsed and continuous Am-Be neutron sources with time gated and continuous gamma ray detectors respectively.The geological formation consists of pure limestone with 15% absolute porosity in a wide range of oil saturation.The particle transport was performed with the Monte Carlo N-Particle Transport Code System, MCNP-4B.Several gamma ray spectra were obtained at the detector position that allow to perform composition analysis of the formation.In particular, the ratio C/O was analyzed as an indicator of oil saturation.Further calculations are proposed to simulate actual detector responses in order to contribute to understand the relation between the detector response with the formation composition

  15. Quantum Monte Carlo Calculations of Neutron Matter

    CERN Document Server

    Carlson, J; Ravenhall, D G

    2003-01-01

    Uniform neutron matter is approximated by a cubic box containing a finite number of neutrons, with periodic boundary conditions. We report variational and Green's function Monte Carlo calculations of the ground state of fourteen neutrons in a periodic box using the Argonne $\\vep $ two-nucleon interaction at densities up to one and half times the nuclear matter density. The effects of the finite box size are estimated using variational wave functions together with cluster expansion and chain summation techniques. They are small at subnuclear densities. We discuss the expansion of the energy of low-density neutron gas in powers of its Fermi momentum. This expansion is strongly modified by the large nn scattering length, and does not begin with the Fermi-gas kinetic energy as assumed in both Skyrme and relativistic mean field theories. The leading term of neutron gas energy is ~ half the Fermi-gas kinetic energy. The quantum Monte Carlo results are also used to calibrate the accuracy of variational calculations ...

  16. RCPO1 - A Monte Carlo program for solving neutron and photon transport problems in three dimensional geometry with detailed energy description and depletion capability

    International Nuclear Information System (INIS)

    The RCP01 Monte Carlo program is used to analyze many geometries of interest in nuclear design and analysis of light water moderated reactors such as the core in its pressure vessel with complex piping arrangement, fuel storage arrays, shipping and container arrangements, and neutron detector configurations. Written in FORTRAN and in use on a variety of computers, it is capable of estimating steady state neutron or photon reaction rates and neutron multiplication factors. The energy range covered in neutron calculations is that relevant to the fission process and subsequent slowing-down and thermalization, i.e., 20 MeV to 0 eV. The same energy range is covered for photon calculations

  17. RCPO1 - A Monte Carlo program for solving neutron and photon transport problems in three dimensional geometry with detailed energy description and depletion capability

    Energy Technology Data Exchange (ETDEWEB)

    Ondis, L.A., II; Tyburski, L.J.; Moskowitz, B.S.

    2000-03-01

    The RCP01 Monte Carlo program is used to analyze many geometries of interest in nuclear design and analysis of light water moderated reactors such as the core in its pressure vessel with complex piping arrangement, fuel storage arrays, shipping and container arrangements, and neutron detector configurations. Written in FORTRAN and in use on a variety of computers, it is capable of estimating steady state neutron or photon reaction rates and neutron multiplication factors. The energy range covered in neutron calculations is that relevant to the fission process and subsequent slowing-down and thermalization, i.e., 20 MeV to 0 eV. The same energy range is covered for photon calculations.

  18. High-fidelity coupled Monte Carlo neutron transport and thermal-hydraulic simulations using Serpent 2/SUBCHANFLOW

    International Nuclear Information System (INIS)

    Highlights: • An internal coupling between Serpent 2 and SUBCHANFLOW is developed and verified. • Temperature and density variations are treated with the on-the-fly TMS method. • Limitation of TMS regarding thermal scattering is evaded by stochastic mixing. • Successful benchmark with MCNP5 and TRIPOLI based multi-physics solutions. • Serpent 2/SUBCHANFLOW applied to full PWR core under hot full power conditions. - Abstract: Efforts to develop high-fidelity, in silico or ab initio, high performance multi-physics tools are undertaken by many groups due to the availability of relatively cheap, large-scale parallel computers. To this end, an internal coupling between the Monte Carlo reactor physics code Serpent 2 and the sub-channel code SUBCHANFLOW has been developed. The coupled code system is intended to serve as reference for deterministic reactor dynamics code developments in the future. It exploits the fact that Serpent was conceived as a lattice code for such deterministic tools. The coupling utilizes Serpent’s recently introduced universal multi-physics interface. With the multi-physics interface enabled, Serpent treats temperature dependence of nuclear data using the target motion sampling method. Since the target motion sampling methodology cannot be applied to thermal bound-atom scattering or unresolved resonances, a stochastic mixing fall back algorithm to enable the simulation of thermal reactors has been implemented. The developed coupled code is verified by code-to-code comparison with an external coupling of the Monte Carlo tool TRIPOLI4 and SUBCHANFLOW as well as the internally coupled code MCNP5/SUBCHANFLOW. Simulation results of all code systems were found to be in good agreement. Thereafter, the second exercise of the OECD/NEA and U.S. NRC PWR MOX/UO2 core transient benchmark is studied to demonstrate that Serpent 2/SUBCHANFLOW may be employed to analyze realistic, industry-like cases such as a full PWR core under hot full power

  19. Neutronics studies of solid targets for spallation neutron source using Monte Carlo simulation

    Institute of Scientific and Technical Information of China (English)

    殷雯; 梁九卿

    2003-01-01

    Neutronics studies for a solid target have been done with Monte Carlo high-energy particle transport code NMTC/JAM,when the proton beam with high kinetic energy bombards the target.The effect of the main parameters of the target on the neutron flux is discussed to optimize the target,which will be used for the concept design of the target of spallation neutron source.A target with its aspect ratio 1.5:1 or 2:1 gives the highest neutron flux.Tungsten is the most acceptable material from the technical and economical points of view.Beryllium as a moderating reflector can increase the neutron flux effectively.

  20. TRIPOLI-4: Monte Carlo transport code functionalities and applications; TRIPOLI-4: code de transport Monte Carlo fonctionnalites et applications

    Energy Technology Data Exchange (ETDEWEB)

    Both, J.P.; Lee, Y.K.; Mazzolo, A.; Peneliau, Y.; Petit, O.; Roesslinger, B. [CEA Saclay, Dir. de l' Energie Nucleaire (DEN), Service d' Etudes de Reacteurs et de Modelisation Avancee, 91 - Gif sur Yvette (France)

    2003-07-01

    Tripoli-4 is a three dimensional calculations code using the Monte Carlo method to simulate the transport of neutrons, photons, electrons and positrons. This code is used in four application fields: the protection studies, the criticality studies, the core studies and the instrumentation studies. Geometry, cross sections, description of sources, principle. (N.C.)

  1. Morse Monte Carlo Radiation Transport Code System

    Energy Technology Data Exchange (ETDEWEB)

    Emmett, M.B.

    1975-02-01

    The report contains sections containing descriptions of the MORSE and PICTURE codes, input descriptions, sample problems, deviations of the physical equations and explanations of the various error messages. The MORSE code is a multipurpose neutron and gamma-ray transport Monte Carlo code. Time dependence for both shielding and criticality problems is provided. General three-dimensional geometry may be used with an albedo option available at any material surface. The PICTURE code provide aid in preparing correct input data for the combinatorial geometry package CG. It provides a printed view of arbitrary two-dimensional slices through the geometry. By inspecting these pictures one may determine if the geometry specified by the input cards is indeed the desired geometry. 23 refs. (WRF)

  2. Deficiency in Monte Carlo simulations of coupled neutron-gamma-ray fields

    NARCIS (Netherlands)

    Maleka, Peane P.; Maucec, Marko; de Meijer, Robert J.

    2011-01-01

    The deficiency in Monte Carlo simulations of coupled neutron-gamma-ray field was investigated by benchmarking two simulation codes with experimental data. Simulations showed better correspondence with the experimental data for gamma-ray transport only. In simulations, the neutron interactions with m

  3. Challenges of Monte Carlo Transport

    Energy Technology Data Exchange (ETDEWEB)

    Long, Alex Roberts [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Computational Physics and Methods (CCS-2)

    2016-06-10

    These are slides from a presentation for Parallel Summer School at Los Alamos National Laboratory. Solving discretized partial differential equations (PDEs) of interest can require a large number of computations. We can identify concurrency to allow parallel solution of discrete PDEs. Simulated particles histories can be used to solve the Boltzmann transport equation. Particle histories are independent in neutral particle transport, making them amenable to parallel computation. Physical parameters and method type determine the data dependencies of particle histories. Data requirements shape parallel algorithms for Monte Carlo. Then, Parallel Computational Physics and Parallel Monte Carlo are discussed and, finally, the results are given. The mesh passing method greatly simplifies the IMC implementation and allows simple load-balancing. Using MPI windows and passive, one-sided RMA further simplifies the implementation by removing target synchronization. The author is very interested in implementations of PGAS that may allow further optimization for one-sided, read-only memory access (e.g. Open SHMEM). The MPICH_RMA_OVER_DMAPP option and library is required to make one-sided messaging scale on Trinitite - Moonlight scales poorly. Interconnect specific libraries or functions are likely necessary to ensure performance. BRANSON has been used to directly compare the current standard method to a proposed method on idealized problems. The mesh passing algorithm performs well on problems that are designed to show the scalability of the particle passing method. BRANSON can now run load-imbalanced, dynamic problems. Potential avenues of improvement in the mesh passing algorithm will be implemented and explored. A suite of test problems that stress DD methods will elucidate a possible path forward for production codes.

  4. Challenges of Monte Carlo Transport

    Energy Technology Data Exchange (ETDEWEB)

    Long, Alex Roberts [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Computational Physics and Methods (CCS-2)

    2016-06-10

    These are slides from a presentation for Parallel Summer School at Los Alamos National Laboratory. Solving discretized partial differential equations (PDEs) of interest can require a large number of computations. We can identify concurrency to allow parallel solution of discrete PDEs. Simulated particles histories can be used to solve the Boltzmann transport equation. Particle histories are independent in neutral particle transport, making them amenable to parallel computation. Physical parameters and method type determine the data dependencies of particle histories. Data requirements shape parallel algorithms for Monte Carlo. Then, Parallel Computational Physics and Parallel Monte Carlo are discussed and finally the results are given. The mesh passing method greatly simplifies the IMC implementation and allows simple load-balancing. Using MPI windows and passive, one-sided RMA further simplifies the implementation by removing target synchronization. The author is very interested in implementations of PGAS that may allow further optimization for one-sided, read-only memory access (e.g. Open SHMEM). The MPICH_RMA_OVER_DMAPP option and library is required to make one-sided messaging scale on Trinitite - Moonlight scales poorly. Interconnect specific libraries or functions are likely necessary to ensure performance. BRANSON has been used to directly compare the current standard method to a proposed method on idealized problems. The mesh passing algorithm performs well on problems that are designed to show the scalability of the particle passing method. BRANSON can now run load-imbalanced, dynamic problems. Potential avenues of improvement in the mesh passing algorithm will be implemented and explored. A suite of test problems that stress DD methods will elucidate a possible path forward for production codes.

  5. ANEMONA: multiassembly neutron transport modeling

    Energy Technology Data Exchange (ETDEWEB)

    Jevremovic, T.; Ito, T. E-mail: t-itoh@nfi.co.jp; Inaba, Y

    2002-11-01

    A new feature of the general geometry neutron transport code, ANEMONA, the modeling of multi-assembly geometries in 2D, is developed and presented in this paper. The new module is called the ANEMULT code. In addition, the two acceleration techniques are added: (a) the ANEMONA's original geometry independent ray tracer (GIT), now utilizes the, so called, virtual bounding volume concept that importantly speeds up the ray tracing, and (b) the flux solver is accelerated using the Chebyshev polynomials. A whole core configuration run by ANEMULT is generated linking assemblies through the boundary edges' flux. All geometrical data are prepared in advance running the ANEMONA code (independently for geometrically different assemblies only). In this paper, two numerical benchmarks are presented: a single BWR MOX fuel assembly and a 6x6 assembly geometry (each assembly is of BWR 9x9 type). The results compared with the Monte Carlo code, GMVP, show a very good agreement.

  6. Monte Carlo methods for particle transport

    CERN Document Server

    Haghighat, Alireza

    2015-01-01

    The Monte Carlo method has become the de facto standard in radiation transport. Although powerful, if not understood and used appropriately, the method can give misleading results. Monte Carlo Methods for Particle Transport teaches appropriate use of the Monte Carlo method, explaining the method's fundamental concepts as well as its limitations. Concise yet comprehensive, this well-organized text: * Introduces the particle importance equation and its use for variance reduction * Describes general and particle-transport-specific variance reduction techniques * Presents particle transport eigenvalue issues and methodologies to address these issues * Explores advanced formulations based on the author's research activities * Discusses parallel processing concepts and factors affecting parallel performance Featuring illustrative examples, mathematical derivations, computer algorithms, and homework problems, Monte Carlo Methods for Particle Transport provides nuclear engineers and scientists with a practical guide ...

  7. Monte Carlo 2000 Conference : Advanced Monte Carlo for Radiation Physics, Particle Transport Simulation and Applications

    CERN Document Server

    Baräo, Fernando; Nakagawa, Masayuki; Távora, Luis; Vaz, Pedro

    2001-01-01

    This book focusses on the state of the art of Monte Carlo methods in radiation physics and particle transport simulation and applications, the latter involving in particular, the use and development of electron--gamma, neutron--gamma and hadronic codes. Besides the basic theory and the methods employed, special attention is paid to algorithm development for modeling, and the analysis of experiments and measurements in a variety of fields ranging from particle to medical physics.

  8. New methods for the Monte Carlo simulation of neutron noise experiments in Ads

    International Nuclear Information System (INIS)

    This paper presents two improvements to speed up the Monte-Carlo simulation of neutron noise experiments. The first one is to separate the actual Monte Carlo transport calculation from the digital signal processing routines, while the second is to introduce non-analogue techniques to improve the efficiency of the Monte Carlo calculation. For the latter method, adaptations to the theory of neutron noise experiments were made to account for the distortion of the higher-moments of the calculated neutron noise. Calculations were performed to test the feasibility of the above outlined scheme and to demonstrate the advantages of the application of the track length estimator. It is shown that the modifications improve the efficiency of these calculations to a high extent, which turns the Monte Carlo method into a powerful tool for the development and design of on-line reactivity measurement systems for ADS

  9. Monte Carlo simulations of a D-T neutron generator shielding for landmine detection

    Energy Technology Data Exchange (ETDEWEB)

    Reda, A.M., E-mail: amreda2005@yahoo.com [College of Science, Shaqra University, Al-Dawadme, P.O. Box 1040 (Saudi Arabia)

    2011-10-15

    Shielding for a D-T sealed neutron generator has been designed using the MCNP5 Monte Carlo radiation transport code. The neutron generator will be used in field for the detection of explosives, landmines, drugs and other 'threat' materials. The optimization of the detection of buried objects was started by studying the signal-to-noise ratio for different geometric conditions. - Highlights: > A landmine detection system based on neutron fast/slow analysis has been designed. > Shielding for a D-T sealed neutron generator tube has been designed using Monte Carlo radiation transport code. > Detection of buried objects was started by studying the signal-to-noise ratio for different geometric conditions. > The signal-to-background ratio optimized at one position for all depths.

  10. Monte-Carlo Simulation on Neutron Instruments at CARR

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The design of high resolution neutron powder diffractometer(HRPD) and two cold neutron guides(CNGs) to be built at China advanced research reactor(CARR) are studied by Monte-Carlo simulation technique.The HRPD instrument is desiged to have a minimum resolution of 0.2% and neutron fluence rate of greater than 106 cm-2 ·s-1 at sample position. The resolution curves, neutron fluence rate and effective neutron beam size at sample position are given. Differences in resolutions and intensity between the

  11. Implementation of variance-reduction techniques for Monte Carlo nuclear logging calculations with neutron sources

    NARCIS (Netherlands)

    Maucec, M

    2005-01-01

    Monte Carlo simulations for nuclear logging applications are considered to be highly demanding transport problems. In this paper, the implementation of weight-window variance reduction schemes in a 'manual' fashion to improve the efficiency of calculations for a neutron logging tool is presented. Th

  12. Design of a transportable high efficiency fast neutron spectrometer

    Science.gov (United States)

    Roecker, C.; Bernstein, A.; Bowden, N. S.; Cabrera-Palmer, B.; Dazeley, S.; Gerling, M.; Marleau, P.; Sweany, M. D.; Vetter, K.

    2016-08-01

    A transportable fast neutron detection system has been designed and constructed for measuring neutron energy spectra and flux ranging from tens to hundreds of MeV. The transportability of the spectrometer reduces the detector-related systematic bias between different neutron spectra and flux measurements, which allows for the comparison of measurements above or below ground. The spectrometer will measure neutron fluxes that are of prohibitively low intensity compared to the site-specific background rates targeted by other transportable fast neutron detection systems. To measure low intensity high-energy neutron fluxes, a conventional capture-gating technique is used for measuring neutron energies above 20 MeV and a novel multiplicity technique is used for measuring neutron energies above 100 MeV. The spectrometer is composed of two Gd containing plastic scintillator detectors arranged around a lead spallation target. To calibrate and characterize the position dependent response of the spectrometer, a Monte Carlo model was developed and used in conjunction with experimental data from gamma ray sources. Multiplicity event identification algorithms were developed and used with a Cf-252 neutron multiplicity source to validate the Monte Carlo model Gd concentration and secondary neutron capture efficiency. The validated Monte Carlo model was used to predict an effective area for the multiplicity and capture gating analyses. For incident neutron energies between 100 MeV and 1000 MeV with an isotropic angular distribution, the multiplicity analysis predicted an effective area of 500 cm2 rising to 5000 cm2. For neutron energies above 20 MeV, the capture-gating analysis predicted an effective area between 1800 cm2 and 2500 cm2. The multiplicity mode was found to be sensitive to the incident neutron angular distribution.

  13. RCP01: a Monte Carlo program for solving neutron and photon transport problems in three-dimensional geometry with detailed energy description (LWBR development program). [For CDC-6600 and -7600, in FORTRAN

    Energy Technology Data Exchange (ETDEWEB)

    Candelore, N R; Gast, R C; Ondis, II, L A

    1978-08-01

    The RCP01 Monte Carlo program for the CDC-7600 and CDC-6600 performs fixed source or eigenfunction neutron reaction rate calculations, or photon reaction rate calculations, for complex geometries. The photon calculations may be linked to the neutron reaction rate calculations. For neutron calculations, the full energy range is treated as required for neutron birth by the fission process and the subsequent neutron slowing down and thermalization, i.e., 10 MeV to 0 eV; for photon calculations the same energy range is treated. The detailed cross sections required for the neutron or photon collision processes are provided by RCPL1. This report provides details of the various types of neutron and photon starts and collisions, the common geometry tracking, and the input required. 37 figures, 1 table.

  14. Scalable Domain Decomposed Monte Carlo Particle Transport

    Energy Technology Data Exchange (ETDEWEB)

    O' Brien, Matthew Joseph [Univ. of California, Davis, CA (United States)

    2013-12-05

    In this dissertation, we present the parallel algorithms necessary to run domain decomposed Monte Carlo particle transport on large numbers of processors (millions of processors). Previous algorithms were not scalable, and the parallel overhead became more computationally costly than the numerical simulation.

  15. Monte Carlo Particle Transport Capability for Inertial Confinement Fusion Applications

    Energy Technology Data Exchange (ETDEWEB)

    Brantley, P S; Stuart, L M

    2006-11-06

    A time-dependent massively-parallel Monte Carlo particle transport calculational module (ParticleMC) for inertial confinement fusion (ICF) applications is described. The ParticleMC package is designed with the long-term goal of transporting neutrons, charged particles, and gamma rays created during the simulation of ICF targets and surrounding materials, although currently the package treats neutrons and gamma rays. Neutrons created during thermonuclear burn provide a source of neutrons to the ParticleMC package. Other user-defined sources of particles are also available. The module is used within the context of a hydrodynamics client code, and the particle tracking is performed on the same computational mesh as used in the broader simulation. The module uses domain-decomposition and the MPI message passing interface to achieve parallel scaling for large numbers of computational cells. The Doppler effects of bulk hydrodynamic motion and the thermal effects due to the high temperatures encountered in ICF plasmas are directly included in the simulation. Numerical results for a three-dimensional benchmark test problem are presented in 3D XYZ geometry as a verification of the basic transport capability. In the full paper, additional numerical results including a prototype ICF simulation will be presented.

  16. Monte Carlo methodologies for neutron streaming in diffusion calculations - Application to directional diffusion coefficients and leakage models in XS generation

    OpenAIRE

    Dorval, Eric

    2016-01-01

    Neutron transport calculations by Monte Carlo methods are finding increased application in nuclear reactor simulations. In particular, a versatile approach entails the use of a 2-step pro-cedure, with Monte Carlo as a few-group cross section data generator at lattice level, followed by deterministic multi-group diffusion calculations at core level. In this thesis, the Serpent 2 Monte Carlo reactor physics burnup calculation code is used in order to test a set of diffusion coefficient model...

  17. Quantum Monte Carlo calculations of two neutrons in finite volume

    OpenAIRE

    Klos, P.; Lynn, J. E.; Tews, I.; Gandolfi, S.; Gezerlis, A.; Hammer, H. -W.; Hoferichter, M.; Schwenk, A.

    2016-01-01

    Ab initio calculations provide direct access to the properties of pure neutron systems that are challenging to study experimentally. In addition to their importance for fundamental physics, their properties are required as input for effective field theories of the strong interaction. In this work, we perform auxiliary-field diffusion Monte Carlo calculations of the ground and first excited state of two neutrons in a finite box, considering a simple contact potential as well as chiral effectiv...

  18. Applications of the Monte Carlo radiation transport toolkit at LLNL

    Science.gov (United States)

    Sale, Kenneth E.; Bergstrom, Paul M., Jr.; Buck, Richard M.; Cullen, Dermot; Fujino, D.; Hartmann-Siantar, Christine

    1999-09-01

    Modern Monte Carlo radiation transport codes can be applied to model most applications of radiation, from optical to TeV photons, from thermal neutrons to heavy ions. Simulations can include any desired level of detail in three-dimensional geometries using the right level of detail in the reaction physics. The technology areas to which we have applied these codes include medical applications, defense, safety and security programs, nuclear safeguards and industrial and research system design and control. The main reason such applications are interesting is that by using these tools substantial savings of time and effort (i.e. money) can be realized. In addition it is possible to separate out and investigate computationally effects which can not be isolated and studied in experiments. In model calculations, just as in real life, one must take care in order to get the correct answer to the right question. Advancing computing technology allows extensions of Monte Carlo applications in two directions. First, as computers become more powerful more problems can be accurately modeled. Second, as computing power becomes cheaper Monte Carlo methods become accessible more widely. An overview of the set of Monte Carlo radiation transport tools in use a LLNL will be presented along with a few examples of applications and future directions.

  19. Neutron transport on the connection machine

    International Nuclear Information System (INIS)

    Monte Carlo methods are heavily used at CEA and account for a a large part of the total CPU time of industrial codes. In the present work (done in the frame of the Parallel Computing Project of the CEL-V Applied Mathematics Department) we study and implement on the Connection Machine an optimised Monte Carlo algorithm for solving the neutron transport equation. This allows us to investigate the suitability of such an architecture for this kind of problem. This report describes the chosen methodology, the algorithm and its performances. We found that programming the CM-2 in CM Fortran is relatively easy and we got interesting performances as, on a 16 k, CM-2 they are the same level as those obtained on one processor of a CRAY X-MP with a well optimized vector code

  20. TRIPOLI-4{sup ®} Monte Carlo code ITER A-lite neutronic model validation

    Energy Technology Data Exchange (ETDEWEB)

    Jaboulay, Jean-Charles, E-mail: jean-charles.jaboulay@cea.fr [CEA, DEN, Saclay, DM2S, SERMA, F-91191 Gif-sur-Yvette (France); Cayla, Pierre-Yves; Fausser, Clement [MILLENNIUM, 16 Av du Québec Silic 628, F-91945 Villebon sur Yvette (France); Damian, Frederic; Lee, Yi-Kang; Puma, Antonella Li; Trama, Jean-Christophe [CEA, DEN, Saclay, DM2S, SERMA, F-91191 Gif-sur-Yvette (France)

    2014-10-15

    3D Monte Carlo transport codes are extensively used in neutronic analysis, especially in radiation protection and shielding analyses for fission and fusion reactors. TRIPOLI-4{sup ®} is a Monte Carlo code developed by CEA. The aim of this paper is to show its capability to model a large-scale fusion reactor with complex neutron source and geometry. A benchmark between MCNP5 and TRIPOLI-4{sup ®}, on the ITER A-lite model was carried out; neutron flux, nuclear heating in the blankets and tritium production rate in the European TBMs were evaluated and compared. The methodology to build the TRIPOLI-4{sup ®} A-lite model is based on MCAM and the MCNP A-lite model. Simplified TBMs, from KIT, were integrated in the equatorial-port. A good agreement between MCNP and TRIPOLI-4{sup ®} is shown; discrepancies are mainly included in the statistical error.

  1. Hybrid Monte-Carlo method for simulating neutron and photon radiography

    International Nuclear Information System (INIS)

    We present a Hybrid Monte-Carlo method (HMCM) for simulating neutron and photon radiographs. HMCM utilizes the combination of a Monte-Carlo particle simulation for calculating incident film radiation and a statistical post-processing routine to simulate film noise. Since the method relies on MCNP for transport calculations, it is easily generalized to most non-destructive evaluation (NDE) simulations. We verify the method's accuracy through ASTM International's E592-99 publication, Standard Guide to Obtainable (E)quivalent Penetrameter Sensitivity for Radiography of Steel Plates [1]. Potential uses for the method include characterizing alternative radiological sources and simulating NDE radiographs

  2. Hybrid Monte-Carlo method for simulating neutron and photon radiography

    Science.gov (United States)

    Wang, Han; Tang, Vincent

    2013-11-01

    We present a Hybrid Monte-Carlo method (HMCM) for simulating neutron and photon radiographs. HMCM utilizes the combination of a Monte-Carlo particle simulation for calculating incident film radiation and a statistical post-processing routine to simulate film noise. Since the method relies on MCNP for transport calculations, it is easily generalized to most non-destructive evaluation (NDE) simulations. We verify the method's accuracy through ASTM International's E592-99 publication, Standard Guide to Obtainable Equivalent Penetrameter Sensitivity for Radiography of Steel Plates [1]. Potential uses for the method include characterizing alternative radiological sources and simulating NDE radiographs.

  3. Monte Carlo calculation of the neutron and gamma sensitivities of self-powered detectors

    Energy Technology Data Exchange (ETDEWEB)

    Pytel, K.

    1981-01-01

    A calculational model is presented for the self-powered detector response prediction in various radiation environments. The fast beta particles and electron transport is treated by Monte Carlo technique. A new model of electronic processes within the insulator is introduced. Calculated neutron and gamma sensitivities of five detectors (with Rh, V, Co, Ag and Pt emitters) are compared with reported experimental values. The comparison gives a satisfactory agreement for the majority of examined detectors.

  4. Monte Carlo calculations of the neutron coincidence gate utilisation factor for passive neutron coincidence counting

    CERN Document Server

    Bourva, L C A

    1999-01-01

    The general purpose neutron-photon-electron Monte Carlo N-Particle code, MCNP sup T sup M , has been used to simulate the neutronic characteristics of the on-site laboratory passive neutron coincidence counter to be installed, under Euratom Safeguards Directorate supervision, at the Sellafield reprocessing plant in Cumbria, UK. This detector is part of a series of nondestructive assay instruments to be installed for the accurate determination of the plutonium content of nuclear materials. The present work focuses on one aspect of this task, namely, the accurate calculation of the coincidence gate utilisation factor. This parameter is an important term in the interpretative model used to analyse the passive neutron coincidence count data acquired using pulse train deconvolution electronics based on the shift register technique. It accounts for the limited proportion of neutrons detected within the time interval for which the electronics gate is open. The Monte Carlo code MCF, presented in this work, represents...

  5. Monte Carlo solution of a semi-discrete transport equation

    International Nuclear Information System (INIS)

    The authors present the S∞ method, a hybrid neutron transport method in which Monte Carlo particles traverse discrete space. The goal of any deterministic/stochastic hybrid method is to couple selected characters from each of the methods in hopes of producing a better method. The S∞ method has the features of the lumped, linear-discontinuous (LLD) spatial discretization, yet it has no ray-effects because of the continuous angular variable. They derive the S∞ method for the solid-state, mono-energetic transport equation in one-dimensional slab geometry with isotropic scattering and an isotropic internal source. They demonstrate the viability of the S∞ method by comparing their results favorably to analytic and deterministic results

  6. Review of neutron noise analysis theory by Monte Carlo simulation

    International Nuclear Information System (INIS)

    Some debates on the theory of neutron noise analysis for reactor kinetic parameter measurement were found before 1970 but a report firmly clearing these debates has not been found, and a question was raised when neutron noise experiments for the TRIGA and HANARO reactors in Korea were performed. In order to clarify this question, the neutron noise experiment is simulated by the Monte Carlo method. This simulation confirms that the widely used equation is approximately valid and that the confusion was caused from the explanation on the derivation of the equation. Rossi-α technique is one of the representative methods of noise analyses for the reactor kinetic parameter measurement, but different opinions were raised for the chain reaction related term in the equation. The equation originally derived at the Los Alamos National Laboratory (LANL) has been widely accepted. However, the others were supported by strict mathematics and experiments as well, and the reason of discrepancy has not been clarified. Since it is the problem of basic concept before the effect of neutron energy or geometry is included, the Monte Carlo simulation for the simplest reactor model could clarify it. For this purpose, the experiment measuring the neutron noise is simulated, and it results that the original equation is approximately valid. However, it is judged that the explanation on the equation by the authors derived it for the first time is not so correct, but Orndoff who made the first experiment by the Ross-α technique explained it rather correctly

  7. Monte Carlo and deterministic computational methods for the calculation of the effective delayed neutron fraction

    Science.gov (United States)

    Zhong, Zhaopeng; Talamo, Alberto; Gohar, Yousry

    2013-07-01

    The effective delayed neutron fraction β plays an important role in kinetics and static analysis of the reactor physics experiments. It is used as reactivity unit referred to as "dollar". Usually, it is obtained by computer simulation due to the difficulty in measuring it experimentally. In 1965, Keepin proposed a method, widely used in the literature, for the calculation of the effective delayed neutron fraction β. This method requires calculation of the adjoint neutron flux as a weighting function of the phase space inner products and is easy to implement by deterministic codes. With Monte Carlo codes, the solution of the adjoint neutron transport equation is much more difficult because of the continuous-energy treatment of nuclear data. Consequently, alternative methods, which do not require the explicit calculation of the adjoint neutron flux, have been proposed. In 1997, Bretscher introduced the k-ratio method for calculating the effective delayed neutron fraction; this method is based on calculating the multiplication factor of a nuclear reactor core with and without the contribution of delayed neutrons. The multiplication factor set by the delayed neutrons (the delayed multiplication factor) is obtained as the difference between the total and the prompt multiplication factors. Using Monte Carlo calculation Bretscher evaluated the β as the ratio between the delayed and total multiplication factors (therefore the method is often referred to as the k-ratio method). In the present work, the k-ratio method is applied by Monte Carlo (MCNPX) and deterministic (PARTISN) codes. In the latter case, the ENDF/B nuclear data library of the fuel isotopes (235U and 238U) has been processed by the NJOY code with and without the delayed neutron data to prepare multi-group WIMSD neutron libraries for the lattice physics code DRAGON, which was used to generate the PARTISN macroscopic cross sections. In recent years Meulekamp and van der Marck in 2006 and Nauchi and Kameyama

  8. Analysis of neutron-reflectometry data by Monte Carlo technique

    CERN Document Server

    Singh, S

    2002-01-01

    Neutron-reflectometry data is collected in momentum space. The real-space information is extracted by fitting a model for the structure of a thin-film sample. We have attempted a Monte Carlo technique to extract the structure of the thin film. In this technique we change the structural parameters of the thin film by simulated annealing based on the Metropolis algorithm. (orig.)

  9. BALTORO a general purpose code for coupling discrete ordinates and Monte-Carlo radiation transport calculations

    International Nuclear Information System (INIS)

    The general purpose code BALTORO was written for coupling the three-dimensional Monte-Carlo /MC/ with the one-dimensional Discrete Ordinates /DO/ radiation transport calculations. The quantity of a radiation-induced /neutrons or gamma-rays/ nuclear effect or the score from a radiation-yielding nuclear effect can be analysed in this way. (author)

  10. Neutron stimulated emission computed tomography: a Monte Carlo simulation approach

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, A C [Department of Biomedical Engineering, Duke University, 136 Hudson Hall, Durham, NC 27708 (United States); Harrawood, B P [Duke Advance Imaging Labs, Department of Radiology, 2424 Erwin Rd, Suite 302, Durham, NC 27705 (United States); Bender, J E [Department of Biomedical Engineering, Duke University, 136 Hudson Hall, Durham, NC 27708 (United States); Tourassi, G D [Duke Advance Imaging Labs, Department of Radiology, 2424 Erwin Rd, Suite 302, Durham, NC 27705 (United States); Kapadia, A J [Department of Biomedical Engineering, Duke University, 136 Hudson Hall, Durham, NC 27708 (United States)

    2007-10-21

    A Monte Carlo simulation has been developed for neutron stimulated emission computed tomography (NSECT) using the GEANT4 toolkit. NSECT is a new approach to biomedical imaging that allows spectral analysis of the elements present within the sample. In NSECT, a beam of high-energy neutrons interrogates a sample and the nuclei in the sample are stimulated to an excited state by inelastic scattering of the neutrons. The characteristic gammas emitted by the excited nuclei are captured in a spectrometer to form multi-energy spectra. Currently, a tomographic image is formed using a collimated neutron beam to define the line integral paths for the tomographic projections. These projection data are reconstructed to form a representation of the distribution of individual elements in the sample. To facilitate the development of this technique, a Monte Carlo simulation model has been constructed from the GEANT4 toolkit. This simulation includes modeling of the neutron beam source and collimation, the samples, the neutron interactions within the samples, the emission of characteristic gammas, and the detection of these gammas in a Germanium crystal. In addition, the model allows the absorbed radiation dose to be calculated for internal components of the sample. NSECT presents challenges not typically addressed in Monte Carlo modeling of high-energy physics applications. In order to address issues critical to the clinical development of NSECT, this paper will describe the GEANT4 simulation environment and three separate simulations performed to accomplish three specific aims. First, comparison of a simulation to a tomographic experiment will verify the accuracy of both the gamma energy spectra produced and the positioning of the beam relative to the sample. Second, parametric analysis of simulations performed with different user-defined variables will determine the best way to effectively model low energy neutrons in tissue, which is a concern with the high hydrogen content in

  11. Monte Carlo simulations of landmine detection using neutron backscattering imaging

    Energy Technology Data Exchange (ETDEWEB)

    Datema, Cor P. E-mail: c.datema@iri.tudelft.nl; Bom, Victor R.; Eijk, Carel W.E. van

    2003-11-01

    Neutron backscattering is a technique that has successfully been applied to the detection of non-metallic landmines. Most of the effort in this field has concentrated on single detectors that are scanned across the soil. Here, two new approaches are presented in which a two-dimensional image of the hydrogen distribution in the soil is made. The first method uses an array of position-sensitive {sup 3}He-tubes that is placed in close proximity of the soil. The second method is based on coded aperture imaging. Here, thermal neutrons from the soil are projected onto a detector which is typically placed one to several meters above the soil. Both methods use a pulsed D/D neutron source. The Monte Carlo simulation package GEANT 4 was used to investigate the performance of both imaging systems.

  12. Monte Carlo simulation of mixed neutron-gamma radiation fields and dosimetry devices

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guoqing

    2011-12-22

    Monte Carlo methods based on random sampling are widely used in different fields for the capability of solving problems with a large number of coupled degrees of freedom. In this work, Monte Carlos methods are successfully applied for the simulation of the mixed neutron-gamma field in an interim storage facility and neutron dosimeters of different types. Details are discussed in two parts: In the first part, the method of simulating an interim storage facility loaded with CASTORs is presented. The size of a CASTOR is rather large (several meters) and the CASTOR wall is very thick (tens of centimeters). Obtaining the results of dose rates outside a CASTOR with reasonable errors costs usually hours or even days. For the simulation of a large amount of CASTORs in an interim storage facility, it needs weeks or even months to finish a calculation. Variance reduction techniques were used to reduce the calculation time and to achieve reasonable relative errors. Source clones were applied to avoid unnecessary repeated calculations. In addition, the simulations were performed on a cluster system. With the calculation techniques discussed above, the efficiencies of calculations can be improved evidently. In the second part, the methods of simulating the response of neutron dosimeters are presented. An Alnor albedo dosimeter was modelled in MCNP, and it has been simulated in the facility to calculate the calibration factor to get the evaluated response to a Cf-252 source. The angular response of Makrofol detectors to fast neutrons has also been investigated. As a kind of SSNTD, Makrofol can detect fast neutrons by recording the neutron induced heavy charged recoils. To obtain the information of charged recoils, general-purpose Monte Carlo codes were used for transporting incident neutrons. The response of Makrofol to fast neutrons is dependent on several factors. Based on the parameters which affect the track revealing, the formation of visible tracks was determined. For

  13. Monte Carlo simulation of mixed neutron-gamma radiation fields and dosimetry devices

    International Nuclear Information System (INIS)

    Monte Carlo methods based on random sampling are widely used in different fields for the capability of solving problems with a large number of coupled degrees of freedom. In this work, Monte Carlos methods are successfully applied for the simulation of the mixed neutron-gamma field in an interim storage facility and neutron dosimeters of different types. Details are discussed in two parts: In the first part, the method of simulating an interim storage facility loaded with CASTORs is presented. The size of a CASTOR is rather large (several meters) and the CASTOR wall is very thick (tens of centimeters). Obtaining the results of dose rates outside a CASTOR with reasonable errors costs usually hours or even days. For the simulation of a large amount of CASTORs in an interim storage facility, it needs weeks or even months to finish a calculation. Variance reduction techniques were used to reduce the calculation time and to achieve reasonable relative errors. Source clones were applied to avoid unnecessary repeated calculations. In addition, the simulations were performed on a cluster system. With the calculation techniques discussed above, the efficiencies of calculations can be improved evidently. In the second part, the methods of simulating the response of neutron dosimeters are presented. An Alnor albedo dosimeter was modelled in MCNP, and it has been simulated in the facility to calculate the calibration factor to get the evaluated response to a Cf-252 source. The angular response of Makrofol detectors to fast neutrons has also been investigated. As a kind of SSNTD, Makrofol can detect fast neutrons by recording the neutron induced heavy charged recoils. To obtain the information of charged recoils, general-purpose Monte Carlo codes were used for transporting incident neutrons. The response of Makrofol to fast neutrons is dependent on several factors. Based on the parameters which affect the track revealing, the formation of visible tracks was determined. For

  14. Establishment and Verification of MCNP Neutron Transport Model About Tianwan Nuclear Power Plant

    Institute of Scientific and Technical Information of China (English)

    ZHOU; Qi

    2012-01-01

    <正>In order to calculating the neutron flux in the surveillance box and reactor pressure vessel of the Tianwan NPP, we need to build up the neutron transport model by using the Monte Carlo code MCNP. The core of the NPP is very complicated for modeling so we put forward some assumptions that can simplify the neutron transport model. A lot of calculation works have been done to prove that the assumptions are right and suitable.

  15. Quantum Monte Carlo calculations of two neutrons in finite volume

    CERN Document Server

    Klos, P; Tews, I; Gandolfi, S; Gezerlis, A; Hammer, H -W; Hoferichter, M; Schwenk, A

    2016-01-01

    Ab initio calculations provide direct access to the properties of pure neutron systems that are challenging to study experimentally. In addition to their importance for fundamental physics, their properties are required as input for effective field theories of the strong interaction. In this work, we perform auxiliary-field diffusion Monte Carlo calculations of the ground and first excited state of two neutrons in a finite box, considering a simple contact potential as well as chiral effective field theory interactions. We compare the results against exact diagonalizations and present a detailed analysis of the finite-volume effects, whose understanding is crucial for determining observables from the calculated energies. Using the L\\"uscher formula, we extract the low-energy S-wave scattering parameters from ground- and excited-state energies for different box sizes.

  16. Resolution and intensity in neutron spectrometry determined by Monte Carlo simulation

    DEFF Research Database (Denmark)

    Dietrich, O.W.

    1968-01-01

    The Monte Carlo simulation technique was applied to the propagation of Bragg-reflected neutrons in mosaic single crystals. The method proved to be very useful for the determination of resolution and intensity in neutron spectrometers.......The Monte Carlo simulation technique was applied to the propagation of Bragg-reflected neutrons in mosaic single crystals. The method proved to be very useful for the determination of resolution and intensity in neutron spectrometers....

  17. Neutron shielding evaluation for a small fuel transport case

    CERN Document Server

    Coeck, M; Vanhavere, F

    2002-01-01

    We investigated the effectiveness of a small neutron shield configuration for the transportation of fresh MOX fuel rods in an experimental facility, this in order to reduce the dose received by the personnel. Monte Carlo simulations using the Tripoli and MCNP4B code were applied. Different configurations were studied, starting from the bare fuel rod positioned on an iron plate up to a fuel rod covered by a box-shaped shield made of different materials such as polyethylene, polyethylene with boron and polyethylene with a cadmium layer. We compared the neutron spectra for the different cases and calculated the corresponding ambient equivalent dose rate H*(10).

  18. Non-analogue Monte Carlo method, application to neutron simulation

    International Nuclear Information System (INIS)

    With most of the traditional and contemporary techniques, it is still impossible to solve the transport equation if one takes into account a fully detailed geometry and if one studies precisely the interactions between particles and matters. Nowadays, only the Monte Carlo method offers such possibilities. However with significant attenuation, the natural simulation remains inefficient: it becomes necessary to use biasing techniques where the solution of the adjoint transport equation is essential. The Monte Carlo code Tripoli has been using such techniques successfully for a long time with different approximate adjoint solutions: these methods require from the user to find out some parameters. If this parameters are not optimal or nearly optimal, the biases simulations may bring about small figures of merit. This paper presents a description of the most important biasing techniques of the Monte Carlo code Tripoli ; then we show how to calculate the importance function for general geometry with multigroup cases. We present a completely automatic biasing technique where the parameters of the biased simulation are deduced from the solution of the adjoint transport equation calculated by collision probabilities. In this study we shall estimate the importance function through collision probabilities method and we shall evaluate its possibilities thanks to a Monte Carlo calculation. We compare different biased simulations with the importance function calculated by collision probabilities for one-group and multigroup problems. We have run simulations with new biasing method for one-group transport problems with isotropic shocks and for multigroup problems with anisotropic shocks. The results show that for the one-group and homogeneous geometry transport problems the method is quite optimal without splitting and russian roulette technique but for the multigroup and heterogeneous X-Y geometry ones the figures of merit are higher if we add splitting and russian roulette

  19. Monte Carlo simulation of a fast neutron counter for use in neutron radiography

    International Nuclear Information System (INIS)

    In this paper, a Geant4 Monte Carlo simulation is employed to evaluate the response of a neutron detection sheet composed of a layer of plexiglas as neutron-to-proton converter and a layer of silver-activated zinc sulphide (ZnS(Ag)) as phosphor. ZnS(Ag) scintillators have the largest light output among the scintillators for fast-neutron spectroscopy. The simulations are performed for 252Cf neutrons which after impinging the converter layer of the detector produce recoil protons. Recoil protons that interact with the scintillator deposit energy which is converted to scintillation light. In this report, different aspects of the ZnS(Ag)-detector, such as the effective converter and scintillator thickness, as well as the detector response are investigated

  20. Monte Carlo simulation of a fast neutron counter for use in neutron radiography

    Science.gov (United States)

    Meshkian, Mohsen

    2015-07-01

    In this paper, a Geant4 Monte Carlo simulation is employed to evaluate the response of a neutron detection sheet composed of a layer of plexiglas as neutron-to-proton converter and a layer of silver-activated zinc sulphide (ZnS(Ag)) as phosphor. ZnS(Ag) scintillators have the largest light output among the scintillators for fast-neutron spectroscopy. The simulations are performed for 252Cf neutrons which after impinging the converter layer of the detector produce recoil protons. Recoil protons that interact with the scintillator deposit energy which is converted to scintillation light. In this report, different aspects of the ZnS(Ag)-detector, such as the effective converter and scintillator thickness, as well as the detector response are investigated.

  1. Neutron transport with periodic boundary conditions

    Energy Technology Data Exchange (ETDEWEB)

    Angelescu, N.; Marinescu, N.; Protopopescu, V.

    1976-01-01

    The initial value problem for monoenergetic neutron transport in homogeneous nonmultiplying, nonabsorbing medium with isotropic scattering and periodic boundary conditions. One completely determines the structure of the spectrum of the transport operator both in plane and parallelepipedic geometries.

  2. Neutron transport equation - indications on homogenization and neutron diffusion

    International Nuclear Information System (INIS)

    In PWR nuclear reactor, the practical study of the neutrons in the core uses diffusion equation to describe the problem. On the other hand, the most correct method to describe these neutrons is to use the Boltzmann equation, or neutron transport equation. In this paper, we give some theoretical indications to obtain a diffusion equation from the general transport equation, with some simplifying hypothesis. The work is organised as follows: (a) the most general formulations of the transport equation are presented: integro-differential equation and integral equation; (b) the theoretical approximation of this Boltzmann equation by a diffusion equation is introduced, by the way of asymptotic developments; (c) practical homogenization methods of transport equation is then presented. In particular, the relationships with some general and useful methods in neutronic are shown, and some homogenization methods in energy and space are indicated. A lot of other points of view or complements are detailed in the text or the remarks

  3. Complete Monte Carlo Simulation of Neutron Scattering Experiments

    International Nuclear Information System (INIS)

    The majority of experiments investigating the elastic scattering of fast neutrons were done some 30 years ago. At that time it was not possible to obtain valid corrections for the finite geometry and the finite sample size of the experimental set up, not even having the main frame computers of the Los Alamos National Laboratory at one’s disposal. The reason was not only the limited calculation capacity of those ancient computers but also, to an even higher degree, the lack of powerful Monte Carlo codes and the very limited data base for the isotope in question. The computing power of a present day PC is about ten thousand times that of a super computer of the1970ies. Moreover, most PCs are idle over-night so that using a powerful Monte Carlo program, like MCNPX from Los Alamos, corrections of important scattering experiments can be determined reliably at practically no computer cost. Surely one of the most important experiments is neutron scattering from liquid helium-3, especially considering the expensive and complicated cryogenic target. A complete documentation of such an experiment as performed in the year 1971 at the Los Alamos National Laboratory is available. Therefore it is now possible to perform a thorough simulation of the experiment: starting from the production of mono-energetic neutrons in a gas target, followed by the interaction in the ambient air, and the interaction with the cryostat structure, and finally the scattering medium itself. Another simulation deals with the scattering from hydrogen as a reference measurement. As two thirds of all available differential scattering cross sections of that reaction depend on these measurements the newly arrived at corrections prove to be highly significant because they are smaller by a factor of five. Moreover, it was necessary to simulate another experiment on this reaction, using a white neutron source. This way it was possible to convert the corresponding relative yield excitation functions to

  4. Kinetic Monte Carlo modelling of neutron irradiation damage in iron

    Energy Technology Data Exchange (ETDEWEB)

    Gamez, L. [Instituto de Fusion Nuclear, UPM, Madrid (Spain); Departamento de Fisica Aplicada, ETSII, UPM, Madrid (Spain)], E-mail: linarejos.gamez@upm.es; Martinez, E. [Instituto de Fusion Nuclear, UPM, Madrid (Spain); Lawrence Livermore National Laboratory, LLNL, CA 94550 (United States); Perlado, J.M.; Cepas, P. [Instituto de Fusion Nuclear, UPM, Madrid (Spain); Caturla, M.J. [Departamento de Fisica Aplicada, Universidad de Alicante, Alicante (Spain); Victoria, M. [Instituto de Fusion Nuclear, UPM, Madrid (Spain); Marian, J. [Lawrence Livermore National Laboratory, LLNL, CA 94550 (United States); Arevalo, C. [Instituto de Fusion Nuclear, UPM, Madrid (Spain); Hernandez, M.; Gomez, D. [CIEMAT, Madrid (Spain)

    2007-10-15

    Ferritic steels (FeCr based alloys) are key materials needed to fulfill the requirements expected in future nuclear fusion facilities, both for magnetic and inertial confinement, and advanced fission reactors (GIV) and transmutation systems. Research in such field is actually a critical aspect in the European research program and abroad. Experimental and multiscale simulation methodologies are going hand by hand in increasing the knowledge of materials performance. At DENIM, it is progressing in some specific part of the well-linked simulation methodology both for defects energetics and diffusion, and for dislocation dynamics. In this study, results obtained from kinetic Monte Carlo simulations of neutron irradiated Fe under different conditions are presented, using modified ad hoc parameters. A significant agreement with experimental measurements has been found for some of the parameterization and mechanisms considered. The results of these simulations are discussed and compared with previous calculations.

  5. MAMONT program for neutron field calculation by the Monte Carlo method

    International Nuclear Information System (INIS)

    The MAMONT program (MAthematical MOdelling of Neutron Trajectories) designed for three-dimensional calculation of neutron transport by analogue and nonanalogue Monte Carlo methods in the range of energies from 15 MeV to the thermal ones is described. The program is written in FORTRAN and is realized at the BESM-6 computer. Group constants of the library modulus are compiled of the ENDL-83, ENDF/B-4 and JENDL-2 files. The possibility of calculation for the layer spherical, cylindrical and rectangular configurations is envisaged. Accumulation and averaging of slowing-down kinetics functionals (averaged logarithmic losses of energy, time of slowing- down, free paths, the number of collisions, age), diffusion parameters, leakage spectra and fluxes as well as formation of separate isotopes over zones are realized in the process of calculation. 16 tabs

  6. Parallelization of MCATNP MONTE CARLO particle transport code by using MPI

    International Nuclear Information System (INIS)

    A Monte Carlo code for simulating Atmospheric Transport of Neutrons and Photons (MCATNP) is used to simulate the ionization effects caused by high altitude nuclear detonation (HAND) and it was parallelized in MPI by adopting the leap random number producer and modifying the original serial code. The parallel results and serial results are identical. The speedup increases almost linearly with the number of processors used. The parallel efficiency is up to to 97% while 16 processors are used, and 94% while 32 are used. The experimental results show that parallelization can obviously reduce the calculation time of Monte Carlo simulation of HAND ionization effects. (authors)

  7. Monte Carlo Simulation for Moderator of Compact D-T Neutron Generator

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    In order to study the neutron moderation of D-T neutron generator, moderators with diffident materials and structures are predicted by Monte Carlo simulations. Neutron generator is simplified as the diameter 20 cm, length 25 cm cylinder. The target is very

  8. Neutron stars - cooling and transport

    CERN Document Server

    Potekhin, A Y; Page, Dany

    2015-01-01

    Observations of thermal radiation from neutron stars can potentially provide information about the states of supranuclear matter in the interiors of these stars with the aid of the theory of neutron-star thermal evolution. We review the basics of this theory for isolated neutron stars with strong magnetic fields, including most relevant thermodynamic and kinetic properties in the stellar core, crust, and blanketing envelopes.

  9. Monte Carlo simulation of moderator and reflector in coal analyzer based on a D-T neutron generator.

    Science.gov (United States)

    Shan, Qing; Chu, Shengnan; Jia, Wenbao

    2015-11-01

    Coal is one of the most popular fuels in the world. The use of coal not only produces carbon dioxide, but also contributes to the environmental pollution by heavy metals. In prompt gamma-ray neutron activation analysis (PGNAA)-based coal analyzer, the characteristic gamma rays of C and O are mainly induced by fast neutrons, whereas thermal neutrons can be used to induce the characteristic gamma rays of H, Si, and heavy metals. Therefore, appropriate thermal and fast neutrons are beneficial in improving the measurement accuracy of heavy metals, and ensure that the measurement accuracy of main elements meets the requirements of the industry. Once the required yield of the deuterium-tritium (d-T) neutron generator is determined, appropriate thermal and fast neutrons can be obtained by optimizing the neutron source term. In this article, the Monte Carlo N-Particle (MCNP) Transport Code and Evaluated Nuclear Data File (ENDF) database are used to optimize the neutron source term in PGNAA-based coal analyzer, including the material and shape of the moderator and neutron reflector. The optimized targets include two points: (1) the ratio of the thermal to fast neutron is 1:1 and (2) the total neutron flux from the optimized neutron source in the sample increases at least 100% when compared with the initial one. The simulation results show that, the total neutron flux in the sample increases 102%, 102%, 85%, 72%, and 62% with Pb, Bi, Nb, W, and Be reflectors, respectively. Maximum optimization of the targets is achieved when the moderator is a 3-cm-thick lead layer coupled with a 3-cm-thick high-density polyethylene (HDPE) layer, and the neutron reflector is a 27-cm-thick hemispherical lead layer.

  10. MCNP-REN a Monte Carlo tool for neutron detector design

    CERN Document Server

    Abhold, M E

    2002-01-01

    The development of neutron detectors makes extensive use of the predictions of detector response through the use of Monte Carlo techniques in conjunction with the point reactor model. Unfortunately, the point reactor model fails to accurately predict detector response in common applications. For this reason, the general Monte Carlo code developed at Los Alamos National Laboratory, Monte Carlo N-Particle (MCNP), was modified to simulate the pulse streams that would be generated by a neutron detector and normally analyzed by a shift register. This modified code, MCNP-Random Exponentially Distributed Neutron Source (MCNP-REN), along with the Time Analysis Program, predicts neutron detector response without using the point reactor model, making it unnecessary for the user to decide whether or not the assumptions of the point model are met for their application. MCNP-REN is capable of simulating standard neutron coincidence counting as well as neutron multiplicity counting. Measurements of mixed oxide fresh fuel w...

  11. The all particle method: Coupled neutron, photon, electron, charged particle Monte Carlo calculations

    International Nuclear Information System (INIS)

    At the present time a Monte Carlo transport computer code is being designed and implemented at Lawrence Livermore National Laboratory to include the transport of: neutrons, photons, electrons and light charged particles as well as the coupling between all species of particles, e.g., photon induced electron emission. Since this code is being designed to handle all particles this approach is called the ''All Particle Method''. The code is designed as a test bed code to include as many different methods as possible (e.g., electron single or multiple scattering) and will be data driven to minimize the number of methods and models ''hard wired'' into the code. This approach will allow changes in the Livermore nuclear and atomic data bases, used to described the interaction and production of particles, to be used to directly control the execution of the program. In addition this approach will allow the code to be used at various levels of complexity to balance computer running time against the accuracy requirements of specific applications. This paper describes the current design philosophy and status of the code. Since the treatment of neutrons and photons used by the All Particle Method code is more or less conventional, emphasis in this paper is placed on the treatment of electron, and to a lesser degree charged particle, transport. An example is presented in order to illustrate an application in which the ability to accurately transport electrons is important. 21 refs., 1 fig

  12. Criticality analysis of thermal reactors for two energy groups applying Monte Carlo and neutron Albedo method

    International Nuclear Information System (INIS)

    The Albedo method applied to criticality calculations to nuclear reactors is characterized by following the neutron currents, allowing to make detailed analyses of the physics phenomena about interactions of the neutrons with the core-reflector set, by the determination of the probabilities of reflection, absorption, and transmission. Then, allowing to make detailed appreciations of the variation of the effective neutron multiplication factor, keff. In the present work, motivated for excellent results presented in dissertations applied to thermal reactors and shieldings, was described the methodology to Albedo method for the analysis criticality of thermal reactors by using two energy groups admitting variable core coefficients to each re-entrant current. By using the Monte Carlo KENO IV code was analyzed relation between the total fraction of neutrons absorbed in the core reactor and the fraction of neutrons that never have stayed into the reflector but were absorbed into the core. As parameters of comparison and analysis of the results obtained by the Albedo method were used one dimensional deterministic code ANISN (ANIsotropic SN transport code) and Diffusion method. The keff results determined by the Albedo method, to the type of analyzed reactor, showed excellent agreement. Thus were obtained relative errors of keff values smaller than 0,78% between the Albedo method and code ANISN. In relation to the Diffusion method were obtained errors smaller than 0,35%, showing the effectiveness of the Albedo method applied to criticality analysis. The easiness of application, simplicity and clarity of the Albedo method constitute a valuable instrument to neutronic calculations applied to nonmultiplying and multiplying media. (author)

  13. Monte Carlo simulation of the neutron monitor yield function

    Science.gov (United States)

    Mangeard, P.-S.; Ruffolo, D.; Sáiz, A.; Madlee, S.; Nutaro, T.

    2016-08-01

    Neutron monitors (NMs) are ground-based detectors that measure variations of the Galactic cosmic ray flux at GV range rigidities. Differences in configuration, electronics, surroundings, and location induce systematic effects on the calculation of the yield functions of NMs worldwide. Different estimates of NM yield functions can differ by a factor of 2 or more. In this work, we present new Monte Carlo simulations to calculate NM yield functions and perform an absolute (not relative) comparison with the count rate of the Princess Sirindhorn Neutron Monitor (PSNM) at Doi Inthanon, Thailand, both for the entire monitor and for individual counter tubes. We model the atmosphere using profiles from the Global Data Assimilation System database and the Naval Research Laboratory Mass Spectrometer, Incoherent Scatter Radar Extended model. Using FLUKA software and the detailed geometry of PSNM, we calculated the PSNM yield functions for protons and alpha particles. An agreement better than 9% was achieved between the PSNM observations and the simulated count rate during the solar minimum of December 2009. The systematic effect from the electronic dead time was studied as a function of primary cosmic ray rigidity at the top of the atmosphere up to 1 TV. We show that the effect is not negligible and can reach 35% at high rigidity for a dead time >1 ms. We analyzed the response function of each counter tube at PSNM using its actual dead time, and we provide normalization coefficients between count rates for various tube configurations in the standard NM64 design that are valid to within ˜1% for such stations worldwide.

  14. Monte Carlo calculation of ''skyshine'' neutron dose from ALS [Advanced Light Source

    International Nuclear Information System (INIS)

    This report discusses the following topics on ''skyshine'' neutron dose from ALS: Sources of radiation; ALS modeling for skyshine calculations; MORSE Monte-Carlo; Implementation of MORSE; Results of skyshine calculations from storage ring; and Comparison of MORSE shielding calculations

  15. MCViNE -- An object oriented Monte Carlo neutron ray tracing simulation package

    CERN Document Server

    Lin, Jiao Y Y; Granroth, Garrett E; Abernathy, Douglas L; Lumsden, Mark D; Winn, Barry; Aczel, Adam A; Aivazis, Michael; Fultz, Brent

    2015-01-01

    MCViNE (Monte-Carlo VIrtual Neutron Experiment) is a versatile Monte Carlo (MC) neutron ray-tracing program that provides researchers with tools for performing computer modeling and simulations that mirror real neutron scattering experiments. By adopting modern software engineering practices such as using composite and visitor design patterns for representing and accessing neutron scatterers, and using recursive algorithms for multiple scattering, MCViNE is flexible enough to handle sophisticated neutron scattering problems including, for example, neutron detection by complex detector systems, and single and multiple scattering events in a variety of samples and sample environments. In addition, MCViNE can take advantage of simulation components in linear-chain-based MC ray tracing packages widely used in instrument design and optimization, as well as NumPy-based components that make prototypes useful and easy to develop. These developments have enabled us to carry out detailed simulations of neutron scatteri...

  16. Neutron Transport Models and Methods for HZETRN and Coupling to Low Energy Light Ion Transport

    Science.gov (United States)

    Blattnig, S.R.; Slaba, T.C.; Heinbockel, J.H.

    2008-01-01

    Exposure estimates inside space vehicles, surface habitats, and high altitude aircraft exposed to space radiation are highly influenced by secondary neutron production. The deterministic transport code HZETRN has been identified as a reliable and efficient tool for such studies, but improvements to the underlying transport models and numerical methods are still necessary. In this paper, the forward-backward (FB) and directionally coupled forward-backward (DC) neutron transport models are derived, numerical methods for the FB model are reviewed, and a computationally efficient numerical solution is presented for the DC model. Both models are compared to the Monte Carlo codes HETCHEDS and FLUKA, and the DC model is shown to agree closely with the Monte Carlo results. Finally, it is found in the development of either model that the decoupling of low energy neutrons from the light ion (A<4) transport procedure adversely affects low energy light ion fluence spectra and exposure quantities. A first order correction is presented to resolve the problem, and it is shown to be both accurate and efficient.

  17. Neutron transport study of a beam port based dynamic neutron radiography facility

    Science.gov (United States)

    Khaial, Anas M.

    Neutron radiography has the ability to differentiate between gas and liquid in two-phase flow due both to the density difference and the high neutron scattering probability of hydrogen. Previous studies have used dynamic neutron radiography -- in both real-time and high-speed -- for air-water, steam-water and gas-liquid metal two-phase flow measurements. Radiography with thermal neutrons is straightforward and efficient as thermal neutrons are easier to detect with relatively higher efficiency and can be easily extracted from nuclear reactor beam ports. The quality of images obtained using neutron radiography and the imaging speed depend on the neutron beam intensity at the imaging plane. A high quality neutron beam, with thermal neutron intensity greater than 3.0x 10 6 n/cm2-s and a collimation ratio greater than 100 at the imaging plane, is required for effective dynamic neutron radiography up to 2000 frames per second. The primary objectives of this work are: (1) to optimize a neutron radiography facility for dynamic neutron radiography applications and (2) to investigate a new technique for three-dimensional neutron radiography using information obtained from neutron scattering. In this work, neutron transport analysis and experimental validation of a dynamic neutron radiography facility is studied with consideration of real-time and high-speed neutron radiography requirements. A beam port based dynamic neutron radiography facility, for a target thermal neutron flux of 1.0x107 n/cm2-s, has been analyzed, constructed and experimentally verified at the McMaster Nuclear Reactor. The neutron source strength at the beam tube entrance is evaluated experimentally by measuring the thermal and fast neutron fluxes using copper activation flux-mapping technique. The development of different facility components, such as beam tube liner, gamma ray filter, beam shutter and biological shield, is achieved analytically using neutron attenuation and divergence theories. Monte-Carlo

  18. Secondary Neutron Doses to Pediatric Patients During Intracranial Proton Therapy: Monte Carlo Simulation of the Neutron Energy Spectrum and its Organ Doses.

    Science.gov (United States)

    Matsumoto, Shinnosuke; Koba, Yusuke; Kohno, Ryosuke; Lee, Choonsik; Bolch, Wesley E; Kai, Michiaki

    2016-04-01

    Proton therapy has the physical advantage of a Bragg peak that can provide a better dose distribution than conventional x-ray therapy. However, radiation exposure of normal tissues cannot be ignored because it is likely to increase the risk of secondary cancer. Evaluating secondary neutrons generated by the interaction of the proton beam with the treatment beam-line structure is necessary; thus, performing the optimization of radiation protection in proton therapy is required. In this research, the organ dose and energy spectrum were calculated from secondary neutrons using Monte Carlo simulations. The Monte Carlo code known as the Particle and Heavy Ion Transport code System (PHITS) was used to simulate the transport proton and its interaction with the treatment beam-line structure that modeled the double scattering body of the treatment nozzle at the National Cancer Center Hospital East. The doses of the organs in a hybrid computational phantom simulating a 5-y-old boy were calculated. In general, secondary neutron doses were found to decrease with increasing distance to the treatment field. Secondary neutron energy spectra were characterized by incident neutrons with three energy peaks: 1×10, 1, and 100 MeV. A block collimator and a patient collimator contributed significantly to organ doses. In particular, the secondary neutrons from the patient collimator were 30 times higher than those from the first scatter. These results suggested that proactive protection will be required in the design of the treatment beam-line structures and that organ doses from secondary neutrons may be able to be reduced. PMID:26910030

  19. Onsager equations and time dependent neutron transport

    International Nuclear Information System (INIS)

    The diffusion of neutrons following an abrupt, localized temperature fluctuation can be conducted in the framework of Onsager-type transport equations. Considering Onsager equations as a generalized Fick's law, time-dependent particle and energy 'generalized diffusion equations' can be obtained. Aim of the present paper is to obtain the time-dependent diffusion Onsager-type equations for the diffusion of neutrons and to apply them to simple trial cases to gain a feeling for their behaviour. (author)

  20. A Monte Carlo simulation and setup optimization of output efficiency to PGNAA thermal neutron using 252Cf neutrons

    Science.gov (United States)

    Zhang, Jin-Zhao; Tuo, Xian-Guo

    2014-07-01

    We present the design and optimization of a prompt γ-ray neutron activation analysis (PGNAA) thermal neutron output setup based on Monte Carlo simulations using MCNP5 computer code. In these simulations, the moderator materials, reflective materials, and structure of the PGNAA 252Cf neutrons of thermal neutron output setup are optimized. The simulation results reveal that the thin layer paraffin and the thick layer of heavy water moderating effect work best for the 252Cf neutron spectrum. Our new design shows a significantly improved performance of the thermal neutron flux and flux rate, that are increased by 3.02 times and 3.27 times, respectively, compared with the conventional neutron source design.

  1. MORSE Monte Carlo radiation transport code system

    International Nuclear Information System (INIS)

    For a number of years the MORSE user community has requested additional help in setting up problems using various options. The sample problems distributed with MORSE did not fully demonstrate the capability of the code. At Oak Ridge National Laboratory the code originators had a complete set of sample problems, but funds for documenting and distributing them were never available. Recently the number of requests for listings of input data and results for running some particular option the user was trying to implement has increased to the point where it is not feasible to handle them on an individual basis. Consequently it was decided to package a set of sample problems which illustrates more adequately how to run MORSE. This write-up may be added to Part III of the MORSE report. These sample problems include a combined neutron-gamma case, a neutron only case, a gamma only case, an adjoint case, a fission case, a time-dependent fission case, the collision density case, an XCHEKR run and a PICTUR run

  2. SU-E-T-569: Neutron Shielding Calculation Using Analytical and Multi-Monte Carlo Method for Proton Therapy Facility

    Energy Technology Data Exchange (ETDEWEB)

    Cho, S; Shin, E H; Kim, J; Ahn, S H; Chung, K; Kim, D-H; Han, Y; Choi, D H [Samsung Medical Center, Seoul (Korea, Republic of)

    2015-06-15

    Purpose: To evaluate the shielding wall design to protect patients, staff and member of the general public for secondary neutron using a simply analytic solution, multi-Monte Carlo code MCNPX, ANISN and FLUKA. Methods: An analytical and multi-Monte Carlo method were calculated for proton facility (Sumitomo Heavy Industry Ltd.) at Samsung Medical Center in Korea. The NCRP-144 analytical evaluation methods, which produced conservative estimates on the dose equivalent values for the shielding, were used for analytical evaluations. Then, the radiation transport was simulated with the multi-Monte Carlo code. The neutron dose at evaluation point is got by the value using the production of the simulation value and the neutron dose coefficient introduced in ICRP-74. Results: The evaluation points of accelerator control room and control room entrance are mainly influenced by the point of the proton beam loss. So the neutron dose equivalent of accelerator control room for evaluation point is 0.651, 1.530, 0.912, 0.943 mSv/yr and the entrance of cyclotron room is 0.465, 0.790, 0.522, 0.453 mSv/yr with calculation by the method of NCRP-144 formalism, ANISN, FLUKA and MCNP, respectively. The most of Result of MCNPX and FLUKA using the complicated geometry showed smaller values than Result of ANISN. Conclusion: The neutron shielding for a proton therapy facility has been evaluated by the analytic model and multi-Monte Carlo methods. We confirmed that the setting of shielding was located in well accessible area to people when the proton facility is operated.

  3. Improved Algorithms and Coupled Neutron-Photon Transport for Auto-Importance Sampling Method

    CERN Document Server

    Wang, Xin; Qiu, Rui; Li, Chun-Yan; Liang, Man-Chun; Zhang, Hui; Li, Jun-Li

    2016-01-01

    Auto-Importance Sampling (AIS) method is a Monte Carlo variance reduction technique proposed by Tsinghua University for deep penetration problem, which can improve computational efficiency significantly without pre-calculations for importance distribution. However AIS method is only validated with several basic deep penetration problems of simple geometries and cannot be used for coupled neutron-photon transport. This paper firstly presented the latest algorithm improvements for AIS method including particle transport, fictitious particles creation and adjustment, fictitious surface geometry, random number allocation and calculation of estimated relative error, which made AIS method applicable to complicated deep penetration problem. Then, a coupled Neutron-Photon Auto-Importance Sampling (NP-AIS) method was proposed to apply AIS method with the improved algorithms in coupled neutron-photon Monte Carlo transport. Finally, the NUREG/CR-6115 PWR benchmark model was calculated with the method of geometry splitti...

  4. Uncertainty analysis of neutron transport calculation

    International Nuclear Information System (INIS)

    A cross section sensitivity-uncertainty analysis code, SUSD was developed. The code calculates sensitivity coefficients for one and two-dimensional transport problems based on the first order perturbation theory. Variance and standard deviation of detector responses or design parameters can be obtained using cross section covariance matrix. The code is able to perform sensitivity-uncertainty analysis for secondary neutron angular distribution(SAD) and secondary neutron energy distribution(SED). Covariances of 6Li and 7Li neutron cross sections in JENDL-3PR1 were evaluated including SAD and SED. Covariances of Fe and Be were also evaluated. The uncertainty of tritium breeding ratio, fast neutron leakage flux and neutron heating was analysed on four types of blanket concepts for a commercial tokamak fusion reactor. The uncertainty of tritium breeding ratio was less than 6 percent. Contribution from SAD/SED uncertainties are significant for some parameters. Formulas to estimate the errors of numerical solution of the transport equation were derived based on the perturbation theory. This method enables us to deterministically estimate the numerical errors due to iterative solution, spacial discretization and Legendre polynomial expansion of transfer cross-sections. The calculational errors of the tritium breeding ratio and the fast neutron leakage flux of the fusion blankets were analysed. (author)

  5. Neutron transport in random media

    Energy Technology Data Exchange (ETDEWEB)

    Makai, M. [KFKI Atomic Energy Research Institute, Budapest (Hungary)

    1996-08-01

    The survey reviews the methods available in the literature which allow a discussion of corium recriticality after a severe accident and a characterization of the corium. It appears that to date no one has considered the eigenvalue problem, though for the source problem several approaches have been proposed. The mathematical formulation of a random medium may be approached in different ways. Based on the review of the literature, we can draw three basic conclusions. The problem of static, random perturbations has been solved. The static case is tractable by the Monte Carlo method. There is a specific time dependent case for which the average flux is given as a series expansion.

  6. Parallel MCNP Monte Carlo transport calculations with MPI

    International Nuclear Information System (INIS)

    The steady increase in computational performance has made Monte Carlo calculations for large/complex systems possible. However, in order to make these calculations practical, order of magnitude increases in performance are necessary. The Monte Carlo method is inherently parallel (particles are simulated independently) and thus has the potential for near-linear speedup with respect to the number of processors. Further, the ever-increasing accessibility of parallel computers, such as workstation clusters, facilitates the practical use of parallel Monte Carlo. Recognizing the nature of the Monte Carlo method and the trends in available computing, the code developers at Los Alamos National Laboratory implemented the message-passing general-purpose Monte Carlo radiation transport code MCNP (version 4A). The PVM package was chosen by the MCNP code developers because it supports a variety of communication networks, several UNIX platforms, and heterogeneous computer systems. This PVM version of MCNP has been shown to produce speedups that approach the number of processors and thus, is a very useful tool for transport analysis. Due to software incompatibilities on the local IBM SP2, PVM has not been available, and thus it is not possible to take advantage of this useful tool. Hence, it became necessary to implement an alternative message-passing library package into MCNP. Because the message-passing interface (MPI) is supported on the local system, takes advantage of the high-speed communication switches in the SP2, and is considered to be the emerging standard, it was selected

  7. Monte Carlo simulation on the application of boron-coated MRPC thermal neutron detector to the compensated neutron logging

    International Nuclear Information System (INIS)

    Background: The compensated neutron logging technology is widely used in oil exploration and development. The neutron detector commonly used in this technology is the helium-3 proportional counter. Due to the decreasing in supply of the helium-3 gas, the price of the helium-3 proportional counter rises quickly. Purpose: The aim is to develop a new type of neutron detector to replace the helium-3 tubes in the compensated neutron logging technology. Methods: A new thermal neutron detector coated with a layer of thermal neutron converter in the inner glass of the Multi-gap Resistive Plate Chamber (MRPC) was developed. Under the conventional and underbalanced conditions, Monte Carlo method was used to simulate the response of the boron-coated MRPC thermal neutron detector and helium-3 proportional counter employed in compensated neutron logging technology. Results: It is shown that the SS/LS increases with the rise of porosity using either the boron-coated MRPC thermal neutron detector or the helium-3 proportional counter, and the results of these two detectors are basically identical. Conclusion: It indicates that the boron-coated MRPC thermal neutron detector can be used for compensated neutron logging. (authors)

  8. Monte Carlo simulation of neutron tomography for palm weevil detection

    International Nuclear Information System (INIS)

    The use of neutron for Non Destructive Imaging (NDI) techniques has many advantages over other (NDI) methods. Using well-established X-ray imaging techniques can provide easy and direct results with some limitations where the sensitivity for light elements is very low. On the other hand, neutron is highly sensitive to water content and can provide extra qualitative information. Comparing the results of the two imaging techniques are investigated in this work with the aim of identifying the palm weevil. At larva stage of the weevil's life it is characterized by highly water content in the trunk of the palm tree which itself composed of spongy watery texture in some types of palm tree. MCNPX 2.5.0 code with neutron radiography tally was used to obtain the 2D projection then reconstructed to 3D tomography image using OSCaR post processing package. The neutron and photon mesh tallies is utilized to study the neutron and photon fluences from monoenergetic thermal neutron beam and neutron spectrum. There are fundamental difficulties in neutron detection which result in misleading information arises from neutron scattering when constructing cone beam CT neutron images, however, neutron radiography provide better methods for the weevil detection from 2D projection. (author)

  9. Monte Carlo modelling of fast neutron scattering by various compounds in view of elaboration of a single shot inspection system

    International Nuclear Information System (INIS)

    Modern, portable or transportable neutron generators, based on the Plasma-Focus principle, are capable to produce a flash of the very intense (up to 109 of 2.45 MeV neutrons from D-D and up to 1011 of 14 MeV neutrons per shot from D-T reactions) and very short neutron pulses (∼ 10 ns). Taking advantage of these capabilities it is possible to determine the elemental content of unknown samples from information existing in a field of scattered neutrons. It allows proposing an alternative approach to the detection of explosives and other illicit materials. The time-of-flight method can be involved in the identification procedure due to the short neutron pulse duration. It is expected that a single shot inspection system can be elaborated on the basis of the proposed method, limited in time only by computer data processing. Results of the Monte Carlo simulations of the scattered neutron field from several compounds (explosives and everyday use materials) are presented in the paper. The MCNP5 code has been used to get info on the angular and energy distributions of neutrons scattered by the above mentioned compounds assuming the initial neutron energy equal to 2.45 MeV (D-D). A new input has been elaborated that allows modeling not only a spectrum of the neutrons scattered at different angles but also their time history from the moment of generation up to detection. Such an approach allows getting approximate signals as registered by hypothetic scintillator+photomultipler probes placed at various distances from the scattering object, demonstrating a principal capability of the method to identify an elemental content of the inspected objects. (author)

  10. Overview and applications of the Monte Carlo radiation transport kit at LLNL

    International Nuclear Information System (INIS)

    Modern Monte Carlo radiation transport codes can be applied to model most applications of radiation, from optical to TeV photons, from thermal neutrons to heavy ions. Simulations can include any desired level of detail in three-dimensional geometries using the right level of detail in the reaction physics. The technology areas to which we have applied these codes include medical applications, defense, safety and security programs, nuclear safeguards and industrial and research system design and control. The main reason such applications are interesting is that by using these tools substantial savings of time and effort (i.e. money) can be realized. In addition it is possible to separate out and investigate computationally effects which can not be isolated and studied in experiments. In model calculations, just as in real life, one must take care in order to get the correct answer to the right question. Advancing computing technology allows extensions of Monte Carlo applications in two directions. First, as computers become more powerful more problems can be accurately modeled. Second, as computing power becomes cheaper Monte Carlo methods become accessible more widely. An overview of the set of Monte Carlo radiation transport tools in use a LLNL will be presented along with a few examples of applications and future directions

  11. Neutron point-flux calculation by Monte Carlo

    International Nuclear Information System (INIS)

    A survey of the usual methods for estimating flux at a point is given. The associated variance-reducing techniques in direct Monte Carlo games are explained. The multigroup Monte Carlo codes MC for critical systems and PUNKT for point source-point detector-systems are represented, and problems in applying the codes to practical tasks are discussed. (author)

  12. Efficient, Automated Monte Carlo Methods for Radiation Transport.

    Science.gov (United States)

    Kong, Rong; Ambrose, Martin; Spanier, Jerome

    2008-11-20

    Monte Carlo simulations provide an indispensible model for solving radiative transport problems, but their slow convergence inhibits their use as an everyday computational tool. In this paper, we present two new ideas for accelerating the convergence of Monte Carlo algorithms based upon an efficient algorithm that couples simulations of forward and adjoint transport equations. Forward random walks are first processed in stages, each using a fixed sample size, and information from stage k is used to alter the sampling and weighting procedure in stage k + 1. This produces rapid geometric convergence and accounts for dramatic gains in the efficiency of the forward computation. In case still greater accuracy is required in the forward solution, information from an adjoint simulation can be added to extend the geometric learning of the forward solution. The resulting new approach should find widespread use when fast, accurate simulations of the transport equation are needed. PMID:23226872

  13. GPU Acceleration of Mean Free Path Based Kernel Density Estimators for Monte Carlo Neutronics Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Burke, TImothy P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kiedrowski, Brian C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martin, William R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Brown, Forrest B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-11-19

    Kernel Density Estimators (KDEs) are a non-parametric density estimation technique that has recently been applied to Monte Carlo radiation transport simulations. Kernel density estimators are an alternative to histogram tallies for obtaining global solutions in Monte Carlo tallies. With KDEs, a single event, either a collision or particle track, can contribute to the score at multiple tally points with the uncertainty at those points being independent of the desired resolution of the solution. Thus, KDEs show potential for obtaining estimates of a global solution with reduced variance when compared to a histogram. Previously, KDEs have been applied to neutronics for one-group reactor physics problems and fixed source shielding applications. However, little work was done to obtain reaction rates using KDEs. This paper introduces a new form of the MFP KDE that is capable of handling general geometries. Furthermore, extending the MFP KDE to 2-D problems in continuous energy introduces inaccuracies to the solution. An ad-hoc solution to these inaccuracies is introduced that produces errors smaller than 4% at material interfaces.

  14. Monte Carlo Model of TRIGA Reactor to Support Neutron Activation Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Zerovnik, G.; Snoj, L.; Trkov, A. [Reactor Physics Department, Jozef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia)

    2011-07-01

    The TRIGA reactor at Jozef Stefan Institute is used as a neutron source for neutron activation analysis. The accuracy of the method depends on the accuracy of the neutron spectrum characterization. Therefore, computational models on different scales have been developed: Monte Carlo full reactor model, model of an irradiation channel and deterministic code for self-shielding factor calculations. The models have been validated by comparing against experiment and thus provide a very strong support for neutron activation analysis of samples irradiated at the TRIGA reactor. (author)

  15. Monte Carlo design for a new neutron collimator at the ENEA Casaccia TRIGA reactor.

    Science.gov (United States)

    Burgio, N; Rosa, R

    2004-10-01

    The TRIGA RC-1 1MW reactor operating at ENEA Casaccia Center is currently being developed as a second neutron imaging facility that shall be devoted to computed tomography as well as neutron tomography. In order to reduce the gamma-ray content in the neutron beam, the reactor tangential piercing channel was selected. A set of Monte Carlo simulation was used to design the neutron collimator, to determine the preliminary choice of the materials to be employed in the collimator design. PMID:15246415

  16. Implict Monte Carlo Radiation Transport Simulations of Four Test Problems

    Energy Technology Data Exchange (ETDEWEB)

    Gentile, N

    2007-08-01

    Radiation transport codes, like almost all codes, are difficult to develop and debug. It is helpful to have small, easy to run test problems with known answers to use in development and debugging. It is also prudent to re-run test problems periodically during development to ensure that previous code capabilities have not been lost. We describe four radiation transport test problems with analytic or approximate analytic answers. These test problems are suitable for use in debugging and testing radiation transport codes. We also give results of simulations of these test problems performed with an Implicit Monte Carlo photonics code.

  17. Parallel processing of Monte Carlo code MCNP for particle transport problem

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, Kenji; Kawasaki, Takuji

    1996-06-01

    It is possible to vectorize or parallelize Monte Carlo codes (MC code) for photon and neutron transport problem, making use of independency of the calculation for each particle. Applicability of existing MC code to parallel processing is mentioned. As for parallel computer, we have used both vector-parallel processor and scalar-parallel processor in performance evaluation. We have made (i) vector-parallel processing of MCNP code on Monte Carlo machine Monte-4 with four vector processors, (ii) parallel processing on Paragon XP/S with 256 processors. In this report we describe the methodology and results for parallel processing on two types of parallel or distributed memory computers. In addition, we mention the evaluation of parallel programming environments for parallel computers used in the present work as a part of the work developing STA (Seamless Thinking Aid) Basic Software. (author)

  18. An Improved Neutron Transport Algorithm for HZETRN

    Science.gov (United States)

    Slaba, Tony C.; Blattnig, Steve R.; Clowdsley, Martha S.; Walker, Steven A.; Badavi, Francis F.

    2010-01-01

    Long term human presence in space requires the inclusion of radiation constraints in mission planning and the design of shielding materials, structures, and vehicles. In this paper, the numerical error associated with energy discretization in HZETRN is addressed. An inadequate numerical integration scheme in the transport algorithm is shown to produce large errors in the low energy portion of the neutron and light ion fluence spectra. It is further shown that the errors result from the narrow energy domain of the neutron elastic cross section spectral distributions, and that an extremely fine energy grid is required to resolve the problem under the current formulation. Two numerical methods are developed to provide adequate resolution in the energy domain and more accurately resolve the neutron elastic interactions. Convergence testing is completed by running the code for various environments and shielding materials with various energy grids to ensure stability of the newly implemented method.

  19. Multipurpose Monte Carlo simulator for photon transport in turbid media

    OpenAIRE

    Guerra, Pedro; Aguirre, Juan; Ortuño, Juan E.; María J Ledesma-Carbayo; Vaquero, Juan José; Desco, Manuel; Santos, Andrés

    2009-01-01

    Monte Carlo methods provide a flexible and rigorous solution to the problem of light transport in turbid media, which enable approaching complex geometries for a closed analytical solution is not feasible. The simulator implements local rules of propagation in the form of probability density functions that depend on the local optical properties of the tissue. This work presents a flexible simulator that can be applied in multiple applications related to optical tomography. In particular...

  20. Monte Carlo Study on Gas Pressure Response of He-3 Tube in Neutron Porosity Logging

    Directory of Open Access Journals (Sweden)

    TIAN Li-li;ZHANG Feng;WANG Xin-guang;LIU Jun-tao

    2016-10-01

    Full Text Available Thermal neutrons are detected by (n,p reaction of Helium-3 tube in the compensated neutron logging. The helium gas pressure in the counting area influences neutron detection efficiency greatly, and then it is an important parameter for neutron porosity measurement accuracy. The variation law of counting rates of a near detector and a far one with helium gas pressure under different formation condition was simulated by Monte Carlo method. The results showed that with the increasing of helium pressure the counting rate of these detectors increased firstly and then leveled off. In addition, the neutron counting rate ratio and porosity sensitivity increased slightly, the porosity measurement error decreased exponentially, which improved the measurement accuracy. These research results can provide technical support for selecting the type of Helium-3 detector in developing neutron porosity logging.

  1. Characterisation of the TRIUMF neutron facility using a Monte Carlo simulation code.

    Science.gov (United States)

    Monk, S D; Abram, T; Joyce, M J

    2015-04-01

    Here, the characterisation of the high-energy neutron field at TRIUMF (The Tri Universities Meson Facility, Vancouver, British Columbia) with Monte Carlo simulation software is described. The package used is MCNPX version 2.6.0, with the neutron fluence rate determined at three locations within the TRIUMF Thermal Neutron Facility (TNF), including the exit of the neutron channel where users of the facility can test devices that may be susceptible to the effects of this form of radiation. The facility is often used to roughly emulate the field likely to be encountered at high altitudes due to radiation of galactic origin and thus the simulated information is compared with the energy spectrum calculated to be due to neutron radiation of cosmic origin at typical aircraft altitudes. The calculated values were also compared with neutron flux measurements that were estimated using the activation of various foils by the staff of the facility, showing agreement within an order of magnitude.

  2. Numerical research on the anisotropic transport of thermal neutron in heterogeneous porous media with micron X-ray computed tomography

    OpenAIRE

    Yong Wang; Wenzheng Yue; Mo Zhang

    2016-01-01

    The anisotropic transport of thermal neutron in heterogeneous porous media is of great research interests in many fields. In this paper, it is the first time that a new model based on micron X-ray computed tomography (CT) has been proposed to simultaneously consider both the separation of matrix and pore and the distribution of mineral components. We apply the Monte Carlo method to simulate thermal neutrons transporting through the model along different directions, and meanwhile detect those ...

  3. Monte Carlo simulation of a single detector unit for the neutron detector array NEDA

    OpenAIRE

    Jaworski, G.; Palacz, M.; Nyberg, Johan; De Angelis, G.; de France, G; Nitto, A. Di; Egea, J.; Erduran, M. N.; Ertürk, S.; Farnea, E.; Gadea, A.; V González; Gottardo, A.(Istituto Nazionale di Fisica Nucleare, Laboratori Nazionali di Legnaro, Legnaro, I-35020, Italy); Hüyük, T.; Kownacki, J.

    2012-01-01

    A study of the dimensions and performance of a single detector of the future neutron detector array NEDA was performed by means of Monte Carlo simulations, using GEANT4. Two different liquid scintillators were evaluated: the hydrogen based BC501A and the deuterated BC537. The efficiency and the probability that one neutron will trigger a signal in more than one detector were investigated as a function of the detector size. The simulations were validated comparing the results to experimental m...

  4. MCViNE - An object oriented Monte Carlo neutron ray tracing simulation package

    Science.gov (United States)

    Lin, Jiao Y. Y.; Smith, Hillary L.; Granroth, Garrett E.; Abernathy, Douglas L.; Lumsden, Mark D.; Winn, Barry; Aczel, Adam A.; Aivazis, Michael; Fultz, Brent

    2016-02-01

    MCViNE (Monte-Carlo VIrtual Neutron Experiment) is an open-source Monte Carlo (MC) neutron ray-tracing software for performing computer modeling and simulations that mirror real neutron scattering experiments. We exploited the close similarity between how instrument components are designed and operated and how such components can be modeled in software. For example we used object oriented programming concepts for representing neutron scatterers and detector systems, and recursive algorithms for implementing multiple scattering. Combining these features together in MCViNE allows one to handle sophisticated neutron scattering problems in modern instruments, including, for example, neutron detection by complex detector systems, and single and multiple scattering events in a variety of samples and sample environments. In addition, MCViNE can use simulation components from linear-chain-based MC ray tracing packages which facilitates porting instrument models from those codes. Furthermore it allows for components written solely in Python, which expedites prototyping of new components. These developments have enabled detailed simulations of neutron scattering experiments, with non-trivial samples, for time-of-flight inelastic instruments at the Spallation Neutron Source. Examples of such simulations for powder and single-crystal samples with various scattering kernels, including kernels for phonon and magnon scattering, are presented. With simulations that closely reproduce experimental results, scattering mechanisms can be turned on and off to determine how they contribute to the measured scattering intensities, improving our understanding of the underlying physics.

  5. Multi-group neutron transport theory

    International Nuclear Information System (INIS)

    Multi-group neutron transport theory. In the paper the general theory of the application of the K. M. Case method to N-group neutron transport theory in plane geometry is given. The eigenfunctions (distributions) for the system of Boltzmann equations have been derived and the completeness theorem has been proved. By means of general solution two examples important for reactor and shielding calculations are given: the solution of a critical and albedo problem for a slab. In both cases the system of singular integral equations for expansion coefficients into a full set of eigenfunction distributions has been reduced to the system of Fredholm-type integral equations. Some results can be applied also to some spherical problems. (author)

  6. Monte Carlo simulations of charge transport in heterogeneous organic semiconductors

    Science.gov (United States)

    Aung, Pyie Phyo; Khanal, Kiran; Luettmer-Strathmann, Jutta

    2015-03-01

    The efficiency of organic solar cells depends on the morphology and electronic properties of the active layer. Research teams have been experimenting with different conducting materials to achieve more efficient solar panels. In this work, we perform Monte Carlo simulations to study charge transport in heterogeneous materials. We have developed a coarse-grained lattice model of polymeric photovoltaics and use it to generate active layers with ordered and disordered regions. We determine carrier mobilities for a range of conditions to investigate the effect of the morphology on charge transport.

  7. Evaluation of vectorized Monte Carlo algorithms on GPUs for a neutron Eigenvalue problem

    Energy Technology Data Exchange (ETDEWEB)

    Du, X.; Liu, T.; Ji, W.; Xu, X. G. [Nuclear Engineering Program, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Brown, F. B. [Monte Carlo Codes Group, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2013-07-01

    Conventional Monte Carlo (MC) methods for radiation transport computations are 'history-based', which means that one particle history at a time is tracked. Simulations based on such methods suffer from thread divergence on the graphics processing unit (GPU), which severely affects the performance of GPUs. To circumvent this limitation, event-based vectorized MC algorithms can be utilized. A versatile software test-bed, called ARCHER - Accelerated Radiation-transport Computations in Heterogeneous Environments - was used for this study. ARCHER facilitates the development and testing of a MC code based on the vectorized MC algorithm implemented on GPUs by using NVIDIA's Compute Unified Device Architecture (CUDA). The ARCHER{sub GPU} code was designed to solve a neutron eigenvalue problem and was tested on a NVIDIA Tesla M2090 Fermi card. We found that although the vectorized MC method significantly reduces the occurrence of divergent branching and enhances the warp execution efficiency, the overall simulation speed is ten times slower than the conventional history-based MC method on GPUs. By analyzing detailed GPU profiling information from ARCHER, we discovered that the main reason was the large amount of global memory transactions, causing severe memory access latency. Several possible solutions to alleviate the memory latency issue are discussed. (authors)

  8. JCOGIN. A parallel programming infrastructure for Monte Carlo particle transport

    International Nuclear Information System (INIS)

    The advantages of the Monte Carlo method for reactor analysis are well known, but the full-core reactor analysis challenges the computational time and computer memory. Meanwhile, the exponential growth of computer power in the last 10 years is now creating a great opportunity for large scale parallel computing on the Monte Carlo full-core reactor analysis. In this paper, a parallel programming infrastructure is introduced for Monte Carlo particle transport, named JCOGIN, which aims at accelerating the development of Monte Carlo codes for the large scale parallelism simulations of the full-core reactor. Now, JCOGIN implements the hybrid parallelism of the spatial decomposition and the traditional particle parallelism on MPI and OpenMP. Finally, JMCT code is developed on JCOGIN, which reaches the parallel efficiency of 70% on 20480 cores for fixed source problem. By the hybrid parallelism, the full-core pin-by-pin simulation of the Dayawan reactor was implemented, with the number of the cells up to 10 million and the tallies of the fluxes utilizing over 40GB of memory. (author)

  9. Update on the development and validation of MERCURY: a modern, Monte Carlo particle transport code

    Energy Technology Data Exchange (ETDEWEB)

    Procassini, R.; Taylor, J.; McKinley, S.; Greenman, G. [Dermott Cullen, Matthew O' Brien, Bret Beck and Christian Hagmann, Lawrence Livermore National Lab., Livermore, CA (United States)

    2005-07-01

    An update on the development and validation of the MERCURY Monte Carlo particle transport code is presented. MERCURY is a modern, parallel, general-purpose Monte Carlo code being developed at the Lawrence Livermore National Laboratory. During the past year, several major algorithm enhancements have been completed. These include the addition of particle trackers for 3-dimensional combinatorial geometry (CG), 1-dimensional radial meshes, 2-dimensional quadrilateral unstructured meshes, as well as a feature known as templates for defining recursive, repeated structures in CG. New physics capabilities include an elastic-scattering neutron thermalization model for free gas and bound, S({alpha}, {beta}) molecular scattering, as well as support for continuous energy cross sections. Each of these new physics features has been validated through code-to-code comparisons with another Monte Carlo transport code. Several important computer science features have been developed, including an extensible input-parameter parser based upon the XML data description language, and a dynamic load-balance methodology for efficient parallel calculations. This paper discusses the recent work in each of these areas, and describes a plan for future extensions that are required to meet the needs of our ever expanding user base. (authors)

  10. Update on the Development and Validation of MERCURY: A Modern, Monte Carlo Particle Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    Procassini, R J; Taylor, J M; McKinley, M S; Greenman, G M; Cullen, D E; O' Brien, M J; Beck, B R; Hagmann, C A

    2005-06-06

    An update on the development and validation of the MERCURY Monte Carlo particle transport code is presented. MERCURY is a modern, parallel, general-purpose Monte Carlo code being developed at the Lawrence Livermore National Laboratory. During the past year, several major algorithm enhancements have been completed. These include the addition of particle trackers for 3-D combinatorial geometry (CG), 1-D radial meshes, 2-D quadrilateral unstructured meshes, as well as a feature known as templates for defining recursive, repeated structures in CG. New physics capabilities include an elastic-scattering neutron thermalization model, support for continuous energy cross sections and S ({alpha}, {beta}) molecular bound scattering. Each of these new physics features has been validated through code-to-code comparisons with another Monte Carlo transport code. Several important computer science features have been developed, including an extensible input-parameter parser based upon the XML data description language, and a dynamic load-balance methodology for efficient parallel calculations. This paper discusses the recent work in each of these areas, and describes a plan for future extensions that are required to meet the needs of our ever expanding user base.

  11. Advanced Monte Carlo procedure for the IFMIF d-Li neutron source term based on evaluated cross section data

    CERN Document Server

    Simakov, S P; Moellendorff, U V; Schmuck, I; Konobeev, A Y; Korovin, Y A; Pereslavtsev, P

    2002-01-01

    A newly developed computational procedure is presented for the generation of d-Li source neutrons in Monte Carlo transport calculations based on the use of evaluated double-differential d+ sup 6 sup , sup 7 Li cross section data. A new code M sup c DeLicious was developed as an extension to MCNP4C to enable neutronics design calculations for the d-Li based IFMIF neutron source making use of the evaluated deuteron data files. The M sup c DeLicious code was checked against available experimental data and calculation results of M sup c DeLi and MCNPX, both of which use built-in analytical models for the Li(d, xn) reaction. It is shown that M sup c DeLicious along with newly evaluated d+ sup 6 sup , sup 7 Li data is superior in predicting the characteristics of the d-Li neutron source. As this approach makes use of tabulated Li(d, xn) cross sections, the accuracy of the IFMIF d-Li neutron source term can be steadily improved with more advanced and validated data.

  12. Neutron production from flattening filter free high energy medical linac: A Monte Carlo study

    Science.gov (United States)

    Najem, M. A.; Abolaban, F. A.; Podolyák, Z.; Spyrou, N. M.

    2015-11-01

    One of the problems arising from using a conventional linac at high energy (>8 MV) is the production of neutrons. One way to reduce neutron production is to remove the flattening filter (FF). The main purpose of this work was to study the effect of FF removal on neutron fluence and neutron dose equivalent inside the treatment room at different photon beam energies. Several simulations based on Monte Carlo techniques were carried out in order to calculate the neutron fluence at different locations in the treatment room from different linac energies with and without a FF. In addition, a step-and-shoot intensity modulated radiotherapy (SnS IMRT) for prostate cancer was modelled using the 15 MV photon beam with and without a FF on a water phantom to calculate the neutron dose received in a full treatment. The results obtained show a significant drop-off in neutrons fluence and dose equivalent when the FF was removed. For example, the neutron fluence was decreased by 54%, 76% and 75% for 10, 15 and 18 MV, respectively. This can decrease the neutron dose to the patient as well as reduce the shielding cost of the treatment room. The neutron dose equivalent of the SnS IMRT for prostate cancer was reduced significantly by 71.3% when the FF was removed. It can be concluded that the flattening filter removal from the head of the linac could reduce the risk of causing secondary cancers and the shielding cost of radiotherapy treatment rooms.

  13. Uncovering flux line correlations in superconductors by reverse monte carlo refinement of neutron scattering data

    OpenAIRE

    Laver, M.; Forgan, E. M.; Abrahamsen, Asger Bech; Bowell, C.; Geue, T.; Cubitt, R.

    2008-01-01

    We describe the use of reverse Monte Carlo refinement to extract structural information from angle-resolved data of a Bragg peak. Starting with small-angle neutron scattering data, the positional order of an ensemble of flux lines in superconducting Nb is revealed. We discuss the uncovered correlation functions in the light of topical theories, in particular, the "Bragg glass" paradigm.

  14. Uncovering flux line correlations in superconductors by reverse monte carlo refinement of neutron scattering data

    DEFF Research Database (Denmark)

    Laver, M.; Forgan, E.M.; Abrahamsen, Asger Bech;

    2008-01-01

    We describe the use of reverse Monte Carlo refinement to extract structural information from angle-resolved data of a Bragg peak. Starting with small-angle neutron scattering data, the positional order of an ensemble of flux lines in superconducting Nb is revealed. We discuss the uncovered correl...

  15. Monte Carlo simulations to advance characterisation of landmines by pulsed fast/thermal neutron analysis

    NARCIS (Netherlands)

    Maucec, M.; Rigollet, C.

    2004-01-01

    The performance of a detection system based on the pulsed fast/thermal neutron analysis technique was assessed using Monte Carlo simulations. The aim was to develop and implement simulation methods, to support and advance the data analysis techniques of the characteristic gamma-ray spectra, potentia

  16. Analytical band Monte Carlo analysis of electron transport in silicene

    Science.gov (United States)

    Yeoh, K. H.; Ong, D. S.; Ooi, C. H. Raymond; Yong, T. K.; Lim, S. K.

    2016-06-01

    An analytical band Monte Carlo (AMC) with linear energy band dispersion has been developed to study the electron transport in suspended silicene and silicene on aluminium oxide (Al2O3) substrate. We have calibrated our model against the full band Monte Carlo (FMC) results by matching the velocity-field curve. Using this model, we discover that the collective effects of charge impurity scattering and surface optical phonon scattering can degrade the electron mobility down to about 400 cm2 V‑1 s‑1 and thereafter it is less sensitive to the changes of charge impurity in the substrate and surface optical phonon. We also found that further reduction of mobility to ∼100 cm2 V‑1 s‑1 as experimentally demonstrated by Tao et al (2015 Nat. Nanotechnol. 10 227) can only be explained by the renormalization of Fermi velocity due to interaction with Al2O3 substrate.

  17. Calculation of effective delayed neutron fraction with modified library of Monte Carlo code

    International Nuclear Information System (INIS)

    Highlights: ► We propose a new Monte Carlo method to calculate the effective delayed neutron fraction by changing the library. ► We study the stability of our method. When the particles and cycles are sufficiently great, the stability is very good. ► The final result is determined to make the deviation least. ► We verify our method on several benchmarks, and the results are very good. - Abstract: A new Monte Carlo method is proposed to calculate the effective delayed neutron fraction βeff. Based on perturbation theory, βeff is calculated with modified library of Monte Carlo code. To verify the proposed method, calculations are performed on several benchmarks. The error of the method is analyzed and the way to reduce error is proposed. The results are in good agreement with the reference data

  18. IB: A Monte Carlo simulation tool for neutron scattering instrument design under PVM and MPI

    International Nuclear Information System (INIS)

    Design of modern neutron scattering instruments relies heavily on Monte Carlo simulation tools for optimization. IB is one such tool written in C++ and implemented under Parallel Virtual Machine and the Message Passing Interface. The program was initially written for the design and optimization of the EQ-SANS instrument at the Spallation Neutron Source. One of its features is the ability to group simple instrument components into more complex ones at the user input level, e.g. grouping neutron mirrors into neutron guides and curved benders. The simulation engine manages the grouped components such that neutrons entering a group are properly operated upon by all components, multiple times if needed, before exiting the group. Thus, only a few basic optical modules are needed at the programming level. For simulations that require higher computer speeds, the program can be compiled and run in parallel modes using either the PVM or the MPI architectures.

  19. A Monte Carlo comparison of PGNAA system performance using 252Cf neutrons, 2.8-MeV neutrons and 14-MeV neutrons

    Science.gov (United States)

    Naqvi, A. A.

    2003-10-01

    Monte Carlo simulations were carried out to compare performance of a 252Cf neutron and a 14-MeV neutron-based prompt γ-ray neutron activation analysis (PGNAA) system with that of the 2.8-MeV neutron-based PGNAA system at King Fahd University of Petroleum and Minerals (KFUPM), Dhahran, Saudi Arabia. Since the energy of neutron beam used in the KFUPM PGNAA system is very close to that produced by a DD neutron generator, performance comparison between a DD and a DT neutron generator-based PGNAA system is highly desired. For the sake of comparison, the calculations were carried out for the PGNAA system with geometry similar to the KFUPM PGNAA system. These calculations were required to determine improvement in performance of the KFUPM PGNAA system if its 2.8-MeV neutron source is replaced by a 252Cf neutron source or a 14-MeV neutron source. Results of the calculations revealed that the geometry of the 252Cf neutron and the 2.8-MeV neutron-based PGNAA system are not significantly different but the geometry of the 14-MeV neutron-based system is significantly different from that of the 2.8-MeV neutron-based PGNAA system. Accordingly, the prompt γ-ray yields from the 252Cf neutron and the 2.8-MeV neutron-based PGNAA system is comparable but prompt γ-ray yields from 14-MeV neutron-based PGNAA system are about three times smaller than that from the 2.8-MeV neutron-based PGNAA system. This study has shown that performance of the 252Cf neutron-based PGNAA system is comparable with that of the 2.8-MeV neutron-based PGNAA system but the performance of the 14-MeV neutron-based PGNAA system is poorer than that of the 2.8-MeV neutron-based PGNAA system.

  20. A Monte Carlo comparison of PGNAA system performance using {sup 252}Cf neutrons, 2.8-MeV neutrons and 14-MeV neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Naqvi, A.A. E-mail: aanaqvi@kfupm.edu.sa

    2003-10-01

    Monte Carlo simulations were carried out to compare performance of a {sup 252}Cf neutron and a 14-MeV neutron-based prompt {gamma}-ray neutron activation analysis (PGNAA) system with that of the 2.8-MeV neutron-based PGNAA system at King Fahd University of Petroleum and Minerals (KFUPM), Dhahran, Saudi Arabia. Since the energy of neutron beam used in the KFUPM PGNAA system is very close to that produced by a DD neutron generator, performance comparison between a DD and a DT neutron generator-based PGNAA system is highly desired. For the sake of comparison, the calculations were carried out for the PGNAA system with geometry similar to the KFUPM PGNAA system. These calculations were required to determine improvement in performance of the KFUPM PGNAA system if its 2.8-MeV neutron source is replaced by a {sup 252}Cf neutron source or a 14-MeV neutron source. Results of the calculations revealed that the geometry of the {sup 252}Cf neutron and the 2.8-MeV neutron-based PGNAA system are not significantly different but the geometry of the 14-MeV neutron-based system is significantly different from that of the 2.8-MeV neutron-based PGNAA system. Accordingly, the prompt {gamma}-ray yields from the {sup 252}Cf neutron and the 2.8-MeV neutron-based PGNAA system is comparable but prompt {gamma}-ray yields from 14-MeV neutron-based PGNAA system are about three times smaller than that from the 2.8-MeV neutron-based PGNAA system. This study has shown that performance of the {sup 252}Cf neutron-based PGNAA system is comparable with that of the 2.8-MeV neutron-based PGNAA system but the performance of the 14-MeV neutron-based PGNAA system is poorer than that of the 2.8-MeV neutron-based PGNAA system.

  1. Monte Carlo calculation of neutron generation time in critical reactor and subcritical reactor with an external source

    International Nuclear Information System (INIS)

    The neutron generation time Λ plays an important role in the reactor kinetics. However, it is not straightforward nor standard in most continuous energy Monte Carlo codes which are able to calculate the prompt neutron lifetime lp directly. The difference between Λ and lp are sometimes very apparent. As very few delayed neutrons are produced in the reactor, they have little influence on Λ. Thus on the assumption that no delayed neutrons are produced in the system, the prompt kinetics equations for critical system and subcritical system with an external source are proposed. And then the equations are applied to calculating Λ with pulsed neutron technique using Monte Carlo. Only one fission neutron source is simulated with Monte Carlo in critical system while two neutron sources, including a fission source and an external source, are simulated for subcritical system. Calculations are performed on both critical benchmarks and subcritical system with an external source and the results are consistent with the reference values. (author)

  2. Monte Carlo and analytical models of neutron detection with organic scintillation detectors

    International Nuclear Information System (INIS)

    This paper presents a new technique for the analysis of neutron pulse height distributions generated in an organic scintillation detector. The methodology presented can be applied to techniques such as neutron spectrum unfolding, which have a variety of applications, including nuclear nonproliferation and homeland security. The technique is based on two independent approaches: (i) the use of the MCNP-PoliMi code to simulate neutron detection on an event-by-event basis with the Monte Carlo method and (ii) an analytical approach for neutron slowing down and detection processes. We show that the total neutron pulse height response measured by the organic scintillators is given by the sum of a large number of different neutron histories, each composed of a certain number of neutron scatterings on hydrogen and/or carbon. The relative contributions of each of these histories are described for a cylindrical liquid scintillator BC-501A. Simulations and measurements of neutron pulse height distributions are essential for neutron spectrum unfolding procedures

  3. The macro response Monte Carlo method for electron transport

    CERN Document Server

    Svatos, M M

    1999-01-01

    This thesis demonstrates the feasibility of basing dose calculations for electrons in radiotherapy on first-principles single scatter physics, in a calculation time that is comparable to or better than current electron Monte Carlo methods. The macro response Monte Carlo (MRMC) method achieves run times that have potential to be much faster than conventional electron transport methods such as condensed history. The problem is broken down into two separate transport calculations. The first stage is a local, single scatter calculation, which generates probability distribution functions (PDFs) to describe the electron's energy, position, and trajectory after leaving the local geometry, a small sphere or "kugel." A number of local kugel calculations were run for calcium and carbon, creating a library of kugel data sets over a range of incident energies (0.25-8 MeV) and sizes (0.025 to 0.1 cm in radius). The second transport stage is a global calculation, in which steps that conform to the size of the kugels in the...

  4. Verification and Validation of MERCURY: A Modern, Monte Carlo Particle Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    Procassini, R J; Cullen, D E; Greenman, G M; Hagmann, C A

    2004-12-09

    Verification and Validation (V&V) is a critical phase in the development cycle of any scientific code. The aim of the V&V process is to determine whether or not the code fulfills and complies with the requirements that were defined prior to the start of the development process. While code V&V can take many forms, this paper concentrates on validation of the results obtained from a modern code against those produced by a validated, legacy code. In particular, the neutron transport capabilities of the modern Monte Carlo code MERCURY are validated against those in the legacy Monte Carlo code TART. The results from each code are compared for a series of basic transport and criticality calculations which are designed to check a variety of code modules. These include the definition of the problem geometry, particle tracking, collisional kinematics, sampling of secondary particle distributions, and nuclear data. The metrics that form the basis for comparison of the codes include both integral quantities and particle spectra. The use of integral results, such as eigenvalues obtained from criticality calculations, is shown to be necessary, but not sufficient, for a comprehensive validation of the code. This process has uncovered problems in both the transport code and the nuclear data processing codes which have since been rectified.

  5. Neutron contamination of Varian Clinac iX 10 MV photon beam using Monte Carlo simulation

    Science.gov (United States)

    Yani, S.; Tursinah, R.; Rhani, M. F.; Soh, R. C. X.; Haryanto, F.; Arif, I.

    2016-03-01

    High energy medical accelerators are commonly used in radiotherapy to increase the effectiveness of treatments. As we know neutrons can be emitted from a medical accelerator if there is an incident of X-ray that hits any of its materials. This issue becomes a point of view of many researchers. The neutron contamination has caused many problems such as image resolution and radiation protection for patients and radio oncologists. This study concerns the simulation of neutron contamination emitted from Varian Clinac iX 10 MV using Monte Carlo code system. As neutron production process is very complex, Monte Carlo simulation with MCNPX code system was carried out to study this contamination. The design of this medical accelerator was modelled based on the actual materials and geometry. The maximum energy of photons and neutron in the scoring plane was 10.5 and 2.239 MeV, respectively. The number and energy of the particles produced depend on the depth and distance from beam axis. From these results, it is pointed out that the neutron produced by linac 10 MV photon beam in a typical treatment is not negligible.

  6. Parallel Deterministic Neutron Transport with AMR

    Energy Technology Data Exchange (ETDEWEB)

    Clouse, C

    2005-03-25

    AMTRAN, a one, two and three dimensional Sn neutron transport code with adaptive mesh refinement (AMR) has been parallelized with MPI over spatial domains and energy groups and with threads over angles. Block refined AMR is used with linear finite element representations for the fluxes, which are node centered. AMR requirements are determined by minimum mean free path calculations throughout the problem and can provide an order of magnitude or more reduction in zoning requirements for the same level of accuracy, compared to a uniformly zoned problem.

  7. VVER-440 Ex-Core Neutron Transport Calculations by MCNP-5 Code and Comparison with Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Borodkin, Pavel; Khrennikov, Nikolay [Scientific and Engineering Centre for Nuclear and Radiation Safety (SEC NRS) Malaya Krasnoselskaya ul., 2/8, bld. 5, 107140 Moscow (Russian Federation)

    2008-07-01

    Ex-core neutron transport calculations are needed to evaluate radiation loading parameters (neutron fluence, fluence rate and spectra) on the in-vessel equipment, reactor pressure vessel (RPV) and support constructions of VVER type reactors. Due to these parameters are used for reactor equipment life-time assessment, neutron transport calculations should be carried out by precise and reliable calculation methods. In case of RPVs, especially, of first generation VVER-440s, the neutron fluence plays a key role in the prediction of RPV lifetime. Main part of VVER ex-core neutron transport calculations are performed by deterministic and Monte-Carlo methods. This paper deals with precise calculations of the Russian first generation VVER-440 by MCNP-5 code. The purpose of this work was an application of this code for expert calculations, verification of results by comparison with deterministic calculations and validation by neutron activation measured data. Deterministic discrete ordinates DORT code, widely used for RPV neutron dosimetry and many times tested by experiments, was used for comparison analyses. Ex-vessel neutron activation measurements at the VVER-440 NPP have provided space (in azimuth and height directions) and neutron energy (different activation reactions) distributions data for experimental (E) validation of calculated results. Calculational intercomparison (DORT vs. MCNP-5) and comparison with measured values (MCNP-5 and DORT vs. E) have shown agreement within 10-15% for different space points and reaction rates. The paper submits a discussion of results and makes conclusions about practice use of MCNP-5 code for ex-core neutron transport calculations in expert analysis. (authors)

  8. The macro response Monte Carlo method for electron transport

    Energy Technology Data Exchange (ETDEWEB)

    Svatos, M M

    1998-09-01

    The main goal of this thesis was to prove the feasibility of basing electron depth dose calculations in a phantom on first-principles single scatter physics, in an amount of time that is equal to or better than current electron Monte Carlo methods. The Macro Response Monte Carlo (MRMC) method achieves run times that are on the order of conventional electron transport methods such as condensed history, with the potential to be much faster. This is possible because MRMC is a Local-to-Global method, meaning the problem is broken down into two separate transport calculations. The first stage is a local, in this case, single scatter calculation, which generates probability distribution functions (PDFs) to describe the electron's energy, position and trajectory after leaving the local geometry, a small sphere or "kugel" A number of local kugel calculations were run for calcium and carbon, creating a library of kugel data sets over a range of incident energies (0.25 MeV - 8 MeV) and sizes (0.025 cm to 0.1 cm in radius). The second transport stage is a global calculation, where steps that conform to the size of the kugels in the library are taken through the global geometry. For each step, the appropriate PDFs from the MRMC library are sampled to determine the electron's new energy, position and trajectory. The electron is immediately advanced to the end of the step and then chooses another kugel to sample, which continues until transport is completed. The MRMC global stepping code was benchmarked as a series of subroutines inside of the Peregrine Monte Carlo code. It was compared to Peregrine's class II condensed history electron transport package, EGS4, and MCNP for depth dose in simple phantoms having density inhomogeneities. Since the kugels completed in the library were of relatively small size, the zoning of the phantoms was scaled down from a clinical size, so that the energy deposition algorithms for spreading dose across 5-10 zones per kugel could

  9. Finite element based composite solution for neutron transport problems

    International Nuclear Information System (INIS)

    A finite element treatment for solving neutron transport problems is presented. The employs region-wise discontinuous finite elements for the spatial representation of the neutron angular flux, while spherical harmonics are used for directional dependence. Composite solutions has been obtained by using different orders of angular approximations in different parts of a system. The method has been successfully implemented for one dimensional slab and two dimensional rectangular geometry problems. An overall reduction in the number of nodal coefficients (more than 60% in some cases as compared to conventional schemes) has been achieved without loss of accuracy with better utilization of computational resources. The method also provides an efficient way of handling physically difficult situations such as treatment of voids in duct problems and sharply changing angular flux. It is observed that a great wealth of information about the spatial and directional dependence of the angular flux is obtained much more quickly as compared to Monte Carlo method, where most of the information in restricted to the locality of immediate interest. (author)

  10. A Monte Carlo simulation of ion transport at finite temperatures

    International Nuclear Information System (INIS)

    We have developed a Monte Carlo simulation for ion transport in hot background gases, which is an alternative way of solving the corresponding Boltzmann equation that determines the distribution function of ions. We consider the limit of low ion densities when the distribution function of the background gas remains unchanged due to collision with ions. Special attention has been paid to properly treating the thermal motion of the host gas particles and their influence on ions, which is very important at low electric fields, when the mean ion energy is comparable to the thermal energy of the host gas. We found the conditional probability distribution of gas velocities that correspond to an ion of specific velocity which collides with a gas particle. Also, we have derived exact analytical formulae for piecewise calculation of the collision frequency integrals. We address the cases when the background gas is monocomponent and when it is a mixture of different gases. The techniques described here are required for Monte Carlo simulations of ion transport and for hybrid models of non-equilibrium plasmas. The range of energies where it is necessary to apply the technique has been defined. The results we obtained are in excellent agreement with the existing ones obtained by complementary methods. Having verified our algorithm, we were able to produce calculations for Ar+ ions in Ar and propose them as a new benchmark for thermal effects. The developed method is widely applicable for solving the Boltzmann equation that appears in many different contexts in physics. (paper)

  11. Monte Carlo simulation of transport from an electrothermal vaporizer

    Energy Technology Data Exchange (ETDEWEB)

    Holcombe, James A. [Department of Chemistry and Biochemistry, University of Texas at Austin, Austin, TX 78712 (United States)]. E-mail: holcombe@mail.utexas.edu; Ertas, Gulay [Department of Chemistry and Biochemistry, University of Texas at Austin, Austin, TX 78712 (United States)

    2006-06-15

    Monte Carlo simulations were developed to elucidate the time and spatial distribution of analyte during the transport process from an electrothermal vaporizer to an inductively coupled plasma. A time-of-flight mass spectrometer was employed to collect experimental data that was compared with the simulated transient signals. Consideration was given to analyte transport as gaseous species as well as aerosol particles. In the case of aerosols, the simulation assumed formation of 5 nm particles and used the Einstein-Stokes equation to estimate the aerosol's diffusion coefficient, which was ca. 1% of the value for free atom diffusion. Desorption conditions for Cu that had been previously elucidated for electrothermal atomic absorption spectrometry were employed for the release processes from the electrothermal vaporizer. The primary distinguishing feature in the output signal to differentiate between gas and aerosol transport was a pronounced, long lived signal after the transient peak if aerosols were transported. Time and spatial distributions of particles within the transport system are presented. This characteristic was supported by independent atomic absorption measurements using a heated (or unheated) quartz T-tube with electrothermal vaporizer introduction.

  12. Generation of organic scintillators response function for fast neutrons using the Monte Carlo method

    International Nuclear Information System (INIS)

    A computer program (DALP) in Fortran-4-G language, has been developed using the Monte Carlo method to simulate the experimental techniques leading to the distribution of pulse heights due to monoenergetic neutrons reaching an organic scintillator. The calculation of the pulse height distribution has been done for two different systems: 1) Monoenergetic neutrons from a punctual source reaching the flat face of a cylindrical organic scintillator; 2) Environmental monoenergetic neutrons randomly reaching either the flat or curved face of the cylindrical organic scintillator. The computer program has been developed in order to be applied to the NE-213 liquid organic scintillator, but can be easily adapted to any other kind of organic scintillator. With this program one can determine the pulse height distribution for neutron energies ranging from 15 KeV to 10 MeV. (Author)

  13. Monte Carlo simulations with MENATE program in order to determine the characteristics of neutron multidetector

    International Nuclear Information System (INIS)

    The neutron multidetector consists of 81 detectors, made of 4x4x12 cmc BC-400 crystals mounted on XP2972 phototubes. This detector placed in the forward direction at 138 cm from the target, was used to detect the correlated neutrons in the fusion of Li11 halo nuclei with Si targets. To verify the criterion for selecting the true coincidences against cross-talk ( a spurious effect in which the same neutron is registered by two or more detectors) and to establish the optimal distance between adjacent detectors, the program MENATE ( written by P.Desesquelles, IPN - Orsay) was used to generate Monte Carlo neutrons and their interactions in multidetector. The results were analysed with PAW (from CERN Library). (authors)

  14. Vector processing of the neutron transport codes

    International Nuclear Information System (INIS)

    One of the large computations in JAERI is the neutron transport ones used for reactor shielding and criticality analyses. The adaptability of vector processings has been investigated on the neutron transport codes under the assumption of future use of super-computer. Five codes have been tested. They are DOT3.5, TWOTRAN and ANISN based on finite difference method, and PALLAS-2DCY and BERMUDA on the direct integration method. It has been found that the gain from vectorization depends upon the numerical methods, geometries, and problems types to be solved. That is, the direct integration is rather suited for vector processing. But in the conventional finite difference method, the difference equation has an unvectorizable recurrence form in (r, z) and (r, -)-geometries. But by altering the interative process, the equation can be vectorized and some gains have been found to be achieved in a criticality problem. For each code, described are some views on vectorization, program restructurings, speedup ratio on F75 APU, numerical studies on the interative process, and so forth. (author)

  15. Development of a stochastic temperature treatment technique for Monte Carlo neutron tracking

    OpenAIRE

    Viitanen, Tuomas

    2015-01-01

    Thermal motion of nuclides has a significant effect on the reaction probabilities and scattering kinematics of neutrons. Since also the nuclides in nuclear reactor materials are in constant thermal motion, the temperature-induced effects need to be taken into account in all neutron transport calculations. This task is notably complicated by the fact that the temperature distributions within operating power reactors are always non-uniform. With conventional transport methods, accurate model...

  16. Neutronic analysis for conversion of the Ghana Research Reactor-1 facility using Monte Carlo methods and UO{sub 2} LEU fuel

    Energy Technology Data Exchange (ETDEWEB)

    Anim-Sampong, S.; Akaho, E.H.K.; Maakuu, B.T.; Gbadago, J.K. [Ghana Research Reactor-1 Centre, Dept. of Nuclear Engineering and Materials Science, National Nuclear Research Institute, Ghana Atomic Energy Commission, Legon, Accra (Ghana); Andam, A. [Kwame Nkrumah Univ. of Science and Technology, Dept. of Physics (Ghana); Liaw, J.J.R.; Matos, J.E. [Argonne National Lab., RERTR Programme, Div. of Nuclear Engineering (United States)

    2007-07-01

    Monte Carlo particle transport methods and software (MCNP) have been applied to the modelling, simulation and neutronic analysis for the conversion of the HEU-fuelled (high enrichment uranium) core of the Ghana Research Reactor-1 (GHARR-1) facility. The results show that the MCNP model of the GHARR-1 facility, which is a commercial version of the Miniature Neutron Source Reactor (MNSR) is good as the simulated neutronic and other reactor physics parameters agree with very well with experimental and zero power results. Three UO{sub 2} LEU (low enrichment uranium) fuels with different enrichments (12.6% and 19.75%), core configurations, core loadings were utilized in the conversion studies. The nuclear criticality and kinetic parameters obtained from the Monte Carlo simulation and neutronic analysis using three UO{sub 2} LEU fuels are in close agreement with results obtained for the reference 90.2% U-Al HEU core. The neutron flux variation in the core, fission chamber and irradiation channels for the LEU UO{sub 2} fuels show the same trend as the HEU core as presented in the paper. The Monte Carlo model confirms a reduction (8% max) in the peak neutron fluxes simulated in the irradiation channels which are utilized for experimental and commercial activities. However, the reductions or 'losses' in the flux levels neither affects the criticality safety, reactor operations and safety nor utilization of the reactor. Employing careful core loading optimization techniques and fuel loadings and enrichment, it is possible to eliminate the apparent reductions or 'losses' in the neutron fluxes as suggested in this paper. Concerning neutronics, it can be concluded that all the 3 LEU fuels qualify as LEU candidates for core conversion of the GHARR-1 facility.

  17. Non-analogue Monte Carlo method, application to neutron simulation; Methode de Monte Carlo non analogue, application a la simulation des neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Morillon, B.

    1996-12-31

    With most of the traditional and contemporary techniques, it is still impossible to solve the transport equation if one takes into account a fully detailed geometry and if one studies precisely the interactions between particles and matters. Only the Monte Carlo method offers such a possibility. However with significant attenuation, the natural simulation remains inefficient: it becomes necessary to use biasing techniques where the solution of the adjoint transport equation is essential. The Monte Carlo code Tripoli has been using such techniques successfully for a long time with different approximate adjoint solutions: these methods require from the user to find out some parameters. If this parameters are not optimal or nearly optimal, the biases simulations may bring about small figures of merit. This paper presents a description of the most important biasing techniques of the Monte Carlo code Tripoli ; then we show how to calculate the importance function for general geometry with multigroup cases. We present a completely automatic biasing technique where the parameters of the biased simulation are deduced from the solution of the adjoint transport equation calculated by collision probabilities. In this study we shall estimate the importance function through collision probabilities method and we shall evaluate its possibilities thanks to a Monte Carlo calculation. We compare different biased simulations with the importance function calculated by collision probabilities for one-group and multigroup problems. We have run simulations with new biasing method for one-group transport problems with isotropic shocks and for multigroup problems with anisotropic shocks. The results show that for the one-group and homogeneous geometry transport problems the method is quite optimal without splitting and russian roulette technique but for the multigroup and heterogeneous X-Y geometry ones the figures of merit are higher if we add splitting and russian roulette technique.

  18. Monte Carlo simulations of neutron-scattering instruments using McStas

    DEFF Research Database (Denmark)

    Nielsen, K.; Lefmann, K.

    2000-01-01

    Monte Carlo simulations have become an essential tool for improving the performance of neutron-scattering instruments, since the level of sophistication in the design of instruments is defeating purely analytical methods. The program McStas, being developed at Rise National Laboratory, includes an...... extension language that makes it easy to adapt it to the particular requirements of individual instruments, and thus provides a powerful and flexible tool for constructing such simulations. McStas has been successfully applied in such areas as neutron guide design, flux optimization, non-Gaussian resolution...

  19. Experimental results and Monte Carlo simulations of a landmine localization device using the neutron backscattering method

    Energy Technology Data Exchange (ETDEWEB)

    Datema, C.P. E-mail: c.datema@iri.tudelft.nl; Bom, V.R.; Eijk, C.W.E. van

    2002-08-01

    Experiments were carried out to investigate the possible use of neutron backscattering for the detection of landmines buried in the soil. Several landmines, buried in a sand-pit, were positively identified. A series of Monte Carlo simulations were performed to study the complexity of the neutron backscattering process and to optimize the geometry of a future prototype. The results of these simulations indicate that this method shows great potential for the detection of non-metallic landmines (with a plastic casing), for which so far no reliable method has been found.

  20. Transport simulation and image reconstruction for fast-neutron detection of explosives and narcotics

    Energy Technology Data Exchange (ETDEWEB)

    Micklich, B.J.; Fink, C.L.; Sagalovsky, L.

    1995-07-01

    Fast-neutron inspection techniques show considerable promise for explosive and narcotics detection. A key advantage of using fast neutrons is their sensitivity to low-Z elements (carbon, nitrogen, and oxygen), which are the primary constituents of these materials. We are currently investigating two interrogation methods in detail: Fast-Neutron Transmission Spectroscopy (FNTS) and Pulsed Fast-Neutron Analysis (PFNA). FNTS is being studied for explosives and narcotics detection in luggage and small containers for which the transmission ratio is greater than about 0.01. The Monte-Carlo radiation transport code MCNP is being used to simulate neutron transmission through a series of phantoms for a few (3-5) projection angles and modest (2 cm) resolution. Areal densities along projection rays are unfolded from the transmission data. Elemental abundances are obtained for individual voxels by tomographic reconstruction, and these reconstructed elemental images are combined to provide indications of the presence or absence of explosives or narcotics. PFNA techniques are being investigated for detection of narcotics in cargo containers because of the good penetration of the fast neutrons and the low attenuation of the resulting high-energy gamma-ray signatures. Analytic models and Monte-Carlo simulations are being used to explore the range of capabilities of PFNA techniques and to provide insight into systems engineering issues. Results of studies from both FNTS and PFNA techniques are presented.

  1. Quantum Monte Carlo calculations of neutron matter with chiral three-body forces

    Science.gov (United States)

    Tews, I.; Gandolfi, S.; Gezerlis, A.; Schwenk, A.

    2016-02-01

    Chiral effective field theory (EFT) enables a systematic description of low-energy hadronic interactions with controlled theoretical uncertainties. For strongly interacting systems, quantum Monte Carlo (QMC) methods provide some of the most accurate solutions, but they require as input local potentials. We have recently constructed local chiral nucleon-nucleon (NN) interactions up to next-to-next-to-leading order (N2LO ). Chiral EFT naturally predicts consistent many-body forces. In this paper, we consider the leading chiral three-nucleon (3N) interactions in local form. These are included in auxiliary field diffusion Monte Carlo (AFDMC) simulations. We present results for the equation of state of neutron matter and for the energies and radii of neutron drops. In particular, we study the regulator dependence at the Hartree-Fock level and in AFDMC and find that present local regulators lead to less repulsion from 3N forces compared to the usual nonlocal regulators.

  2. Overview of TRIPOLI-4 version 7, Continuous-energy Monte Carlo Transport Code

    International Nuclear Information System (INIS)

    The TRIPOLI-4 code is used essentially for four major classes of applications: shielding studies, criticality studies, core physics studies, and instrumentation studies. In this updated overview of the Monte Carlo transport code TRIPOLI-4, we list and describe its current main features, including recent developments or extended capacities like effective beta estimation, photo-nuclear reactions or extended mesh tallies. The code computes coupled neutron-photon propagation as well as the electron-photon cascade shower. While providing the user with common biasing techniques, it also implements an automatic weighting scheme. TRIPOLI-4 has support for execution in parallel mode. Special features and applications are also presented concerning: 'particles storage', resuming a stopped TRIPOLI-4 run, collision bands, Green's functions, source convergence in criticality mode, and mesh tally

  3. Domain Decomposition of a Constructive Solid Geometry Monte Carlo Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    O' Brien, M J; Joy, K I; Procassini, R J; Greenman, G M

    2008-12-07

    Domain decomposition has been implemented in a Constructive Solid Geometry (CSG) Monte Carlo neutron transport code. Previous methods to parallelize a CSG code relied entirely on particle parallelism; but in our approach we distribute the geometry as well as the particles across processors. This enables calculations whose geometric description is larger than what could fit in memory of a single processor, thus it must be distributed across processors. In addition to enabling very large calculations, we show that domain decomposition can speed up calculations compared to particle parallelism alone. We also show results of a calculation of the proposed Laser Inertial-Confinement Fusion-Fission Energy (LIFE) facility, which has 5.6 million CSG parts.

  4. Feasibility Study of Neutron Dose for Real Time Image Guided Proton Therapy: A Monte Carlo Study

    OpenAIRE

    Kim, Jin Sung; Shin, Jung Suk; Kim, Daehyun; Shin, EunHyuk; Chung, Kwangzoo; Cho, Sungkoo; Ahn, Sung Hwan; Ju, Sanggyu; Chung, Yoonsun; Jung, Sang Hoon; Han, Youngyih

    2015-01-01

    Two full rotating gantry with different nozzles (Multipurpose nozzle with MLC, Scanning Dedicated nozzle) with conventional cyclotron system is installed and under commissioning for various proton treatment options at Samsung Medical Center in Korea. The purpose of this study is to investigate neutron dose equivalent per therapeutic dose, H/D, to x-ray imaging equipment under various treatment conditions with monte carlo simulation. At first, we investigated H/D with the various modifications...

  5. A unified Monte Carlo approach to fast neutron cross section data evaluation.

    Energy Technology Data Exchange (ETDEWEB)

    Smith, D.; Nuclear Engineering Division

    2008-03-03

    A unified Monte Carlo (UMC) approach to fast neutron cross section data evaluation that incorporates both model-calculated and experimental information is described. The method is based on applications of Bayes Theorem and the Principle of Maximum Entropy as well as on fundamental definitions from probability theory. This report describes the formalism, discusses various practical considerations, and examines a few numerical examples in some detail.

  6. Load balancing in highly parallel processing of Monte Carlo code for particle transport

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, Kenji; Takemiya, Hiroshi [Japan Atomic Energy Research Inst., Tokyo (Japan); Kawasaki, Takuji [Fuji Research Institute Corporation, Tokyo (Japan)

    2001-01-01

    In parallel processing of Monte Carlo(MC) codes for neutron, photon and electron transport problems, particle histories are assigned to processors making use of independency of the calculation for each particle. Although we can easily parallelize main part of a MC code by this method, it is necessary and practically difficult to optimize the code concerning load balancing in order to attain high speedup ratio in highly parallel processing. In fact, the speedup ratio in the case of 128 processors remains in nearly one hundred times when using the test bed for the performance evaluation. Through the parallel processing of the MCNP code, which is widely used in the nuclear field, it is shown that it is difficult to attain high performance by static load balancing in especially neutron transport problems, and a load balancing method, which dynamically changes the number of assigned particles minimizing the sum of the computational and communication costs, overcomes the difficulty, resulting in nearly fifteen percentage of reduction for execution time. (author)

  7. Load balancing in highly parallel processing of Monte Carlo code for particle transport

    International Nuclear Information System (INIS)

    In parallel processing of Monte Carlo(MC) codes for neutron, photon and electron transport problems, particle histories are assigned to processors making use of independency of the calculation for each particle. Although we can easily parallelize main part of a MC code by this method, it is necessary and practically difficult to optimize the code concerning load balancing in order to attain high speedup ratio in highly parallel processing. In fact, the speedup ratio in the case of 128 processors remains in nearly one hundred times when using the test bed for the performance evaluation. Through the parallel processing of the MCNP code, which is widely used in the nuclear field, it is shown that it is difficult to attain high performance by static load balancing in especially neutron transport problems, and a load balancing method, which dynamically changes the number of assigned particles minimizing the sum of the computational and communication costs, overcomes the difficulty, resulting in nearly fifteen percentage of reduction for execution time. (author)

  8. Auxiliary-Field Quantum Monte Carlo Simulations of Neutron Matter in Chiral Effective Field Theory

    CERN Document Server

    Wlazłowski, G; Moroz, S; Bulgac, A; Roche, K J

    2014-01-01

    We present variational Monte Carlo calculations of the neutron matter equation of state using chiral nuclear interactions. The ground-state wavefunction of neutron matter, containing non-perturbative many-body correlations, is obtained from auxiliary-field quantum Monte Carlo simulations of up to about 340 neutrons interacting on a 10^3 discretized lattice. The evolution Hamiltonian is chosen to be attractive and spin-independent in order to avoid the fermion sign problem and is constructed to best reproduce broad features of chiral nuclear forces. This is facilitated by choosing a lattice spacing of 1.5 fm, corresponding to a momentum-space cutoff of 414 MeV/c, a resolution scale at which strongly repulsive features of nuclear two-body forces are suppressed. Differences between the evolution potential and the full chiral nuclear interaction are then treated perturbatively. Our results for the equation of state are compared to previous quantum Monte Carlo simulations which employed chiral two-body forces at n...

  9. Using Monte Carlo transport to accurately predict isotope production and activation analysis rates at the University of Missouri research reactor

    International Nuclear Information System (INIS)

    A detailed Monte Carlo N-Particle Transport Code (MCNP5) model of the University of Missouri research reactor (MURR) has been developed. The ability of the model to accurately predict isotope production rates was verified by comparing measured and calculated neutron- capture reaction rates for numerous isotopes. In addition to thermal (1/v) monitors, the benchmarking included a number of isotopes whose (n, γ) reaction rates are very sensitive to the epithermal portion of the neutron spectrum. Using the most recent neutron libraries (ENDF/ B-VII.0), the model was able to accurately predict the measured reaction rates in all cases. The model was then combined with ORIGEN 2.2, via MONTEBURNS 2.0, to calculate production of 99Mo from fission of low-enriched uranium foils. The model was used to investigate both annular and plate LEU foil targets in a variety of arrangements in a graphite irradiation wedge to optimize the production of 99Mo. (author)

  10. Verification of Monte Carlo transport codes FLUKA, Mars and Shield

    International Nuclear Information System (INIS)

    The present study is a continuation of the project 'Verification of Monte Carlo Transport Codes' which is running at GSI as a part of activation studies of FAIR relevant materials. It includes two parts: verification of stopping modules of FLUKA, MARS and SHIELD-A (with ATIMA stopping module) and verification of their isotope production modules. The first part is based on the measurements of energy deposition function of uranium ions in copper and stainless steel. The irradiation was done at 500 MeV/u and 950 MeV/u, the experiment was held at GSI from September 2004 until May 2005. The second part is based on gamma-activation studies of an aluminium target irradiated with an argon beam of 500 MeV/u in August 2009. Experimental depth profiling of the residual activity of the target is compared with the simulations. (authors)

  11. A Monte Carlo simulation of ultra-cold neutron production by Bragg reflection from a moving single crystal

    International Nuclear Information System (INIS)

    A Monte Carlo simulation was performed of a 'Gedanken Experiment' where ultra-cold neutrons are produced by Bragg reflection from a moving mosaic single crystal. It is shown that ultra-cold neutrons can be obtained by using thermal or cold neutrons (in practice only the latter). The space and velocity distributions of the reflected neutrons are calculated and it is shown that the cross-section of the reflected ultra-cold neutron beam is of elliptical shape. The length of the minor axis of this ellipse has an upper limit determined by the mosaic spread of the moving crystal, and the length of the major axis increases with the ratio of the velocity of the incident neutrons to the velocity of the reflected neutrons. The proposed method of production of ultra-cold neutrons might be useful in cases where a beam of ultra-cold quasimonochromatic neutrons is required. (Auth.)

  12. Monte Carlo simulation of the neutron guide system for the SNS engineering diffractometer

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X.L.; Lee, W.T. [Spallation Neutron Source, Oak Ridge National Laboratory, Oak Ridge, TN (United States)

    2001-03-01

    VULCAN, the SNS engineering diffractometer, is designed to tackle a broad range of engineering problems, from residual stress distribution in components to materials response under loading. In VULCAN, neutrons are delivered to the sample position via a series of straight and curved neutron guides. An interchangeable guide-collimator system is planned in the incident beam path, allowing the instrument to be optimally configured for individual experiments with different intensity-resolution requirements. To achieve maximum data rate and large d-spacing coverage, detectors are employed continuously from 60deg to 150deg in the horizontal scattering plane and -30deg to 30deg in the vertical plane. To enable simultaneous small angle scattering measurements for characterization of the microstructure, the instrument is also equipped with a position sensitive area detector. Monte Carlo simulation indicates that the proposed neutron guide system is able to deliver the desired intensity and resolution. (author)

  13. Neutron strain scanning in bimetallic materials. Experimental and Monte Carlo simulation results

    International Nuclear Information System (INIS)

    Complete text of publication follows. Neutron diffraction measurements have been carried out on the REST diffractometer on curved components fabricated by cold working bimetallic tubes. The tubes consist of two layers (an outer one of austenitic steel and an inner one of ferritic steel) with a total wall thickness of 6 mm. Both austenitic and ferritic components have been scanned at different positions, throughout the material thickness and for three orientations of the component axes with respect to the neutron momentum transfer vector. Due to the complicated geometry of the problem, Bragg peak data have been corrected for non-uniform illumination of gauge volume, neutron absorption and instrumental effects by means of a Monte Carlo simulation code which incorporates details of the diffractometer and a realistic model of the specimen. We shall report on estimations of the stress tensor components and on the combined micro-stress and coherence volume effects on the Bragg peak linewidths. (author)

  14. COLLI-PTB, Neutron Fluence Spectra for 3-D Collimator System by Monte-Carlo

    International Nuclear Information System (INIS)

    1 - Description of program or function: For optimizing collimator systems (shieldings) for fast neutrons with energies between 10 KeV and 20 MeV. Only elastic and inelastic neutron scattering processes are involved. Isotropic angular distribution for inelastic scattering in the center of mass system is assumed. 2 - Method of solution: The Monte Carlo method with importance sampling technique, splitting and Russian Roulette is used. The neutron attenuation and scattering kinematics is taken into account. 3 - Restrictions on the complexity of the problem: Energy range from 10 KeV to 20 MeV. For the output spectra any bin width is possible. The output spectra are confined to 40 equidistant channels

  15. Monte Carlo simulations as a feasibility tool for non-metallic land-mine detection by thermal-neutron backscattering

    NARCIS (Netherlands)

    Maucec, M; de Meijer, RJ

    2002-01-01

    The use of Monte Carlo simulations is presented for modelling a simplified land-mine detector system with thermal neutron backscattering (TNB) analysis based on a Cf-252-neutron source. Different aspects and a variety of external conditions, related to localisation and identification of a buried obj

  16. Parallelization of a Monte Carlo particle transport simulation code

    Science.gov (United States)

    Hadjidoukas, P.; Bousis, C.; Emfietzoglou, D.

    2010-05-01

    We have developed a high performance version of the Monte Carlo particle transport simulation code MC4. The original application code, developed in Visual Basic for Applications (VBA) for Microsoft Excel, was first rewritten in the C programming language for improving code portability. Several pseudo-random number generators have been also integrated and studied. The new MC4 version was then parallelized for shared and distributed-memory multiprocessor systems using the Message Passing Interface. Two parallel pseudo-random number generator libraries (SPRNG and DCMT) have been seamlessly integrated. The performance speedup of parallel MC4 has been studied on a variety of parallel computing architectures including an Intel Xeon server with 4 dual-core processors, a Sun cluster consisting of 16 nodes of 2 dual-core AMD Opteron processors and a 200 dual-processor HP cluster. For large problem size, which is limited only by the physical memory of the multiprocessor server, the speedup results are almost linear on all systems. We have validated the parallel implementation against the serial VBA and C implementations using the same random number generator. Our experimental results on the transport and energy loss of electrons in a water medium show that the serial and parallel codes are equivalent in accuracy. The present improvements allow for studying of higher particle energies with the use of more accurate physical models, and improve statistics as more particles tracks can be simulated in low response time.

  17. Reliability of Monte Carlo simulations in modeling neutron yields from a shielded fission source

    Science.gov (United States)

    McArthur, Matthew S.; Rees, Lawrence B.; Czirr, J. Bart

    2016-08-01

    Using the combination of a neutron-sensitive 6Li glass scintillator detector with a neutron-insensitive 7Li glass scintillator detector, we are able to make an accurate measurement of the capture rate of fission neutrons on 6Li. We used this detector with a 252Cf neutron source to measure the effects of both non-borated polyethylene and 5% borated polyethylene shielding on detection rates over a range of shielding thicknesses. Both of these measurements were compared with MCNP calculations to determine how well the calculations reproduced the measurements. When the source is highly shielded, the number of interactions experienced by each neutron prior to arriving at the detector is large, so it is important to compare Monte Carlo modeling with actual experimental measurements. MCNP reproduces the data fairly well, but it does generally underestimate detector efficiency both with and without polyethylene shielding. For non-borated polyethylene it underestimates the measured value by an average of 8%. This increases to an average of 11% for borated polyethylene.

  18. Monte Carlo evaluation of the neutron detection efficiency of a superheated drop detector

    Energy Technology Data Exchange (ETDEWEB)

    Gualdrini, G. F. [ENEA, Centro Ricerche `Ezio Clementel`, Bologna (Italy). Dipt. Ambiente; D`Errico, F.; Noccioni, P. [Pisa, Univ. (Italy). Dipt. di Costruzioni Meccaniche e Nucleari

    1997-06-01

    Neutron dosimetry has recently gained renewed attention, following concerns on the exposure of crew members on board aircraft, and of workers around the increasing number of high energy accelerators for medical and research purposes. At the same time the new operational quantities for radiation dosimetry introduced by ICRU and the ICRP, aiming at a unified metrological system applicable to all types of radiation exposure, involved the need to update current devices in order to meet new requirements. Superheated Drop (Bubble) Detectors (SDD) offer an alternative approach to neutron radiation protection dosimetry. The SDDs are currently studied within a large collaborative effort involving Yale University, New Haven CT, the `Universita` degli Studi di Pisa`, the Physikalisch-Technische Bundesanstalt, Braunschweig D. and ENEA (National Agency for New Technology, Energy and the Environment)-C.R., Bologna. The detectors were characterised through calibrations with monoenergetic neutron beams and where experimental investigations were inadequate or impossible, such as in the intermediate energy range, parametric Monte Carlo calculations of the response were carried out. This report describes the general characteristics of the SDDs along with the Monte Carlo computations of the energy response and a comparison with the experimental results.

  19. On-the-fly sampling of temperature-dependent thermal neutron scattering data for Monte Carlo simulations

    International Nuclear Information System (INIS)

    Highlights: • Method of on-the-fly sampling S(α,β) data at any temperature is proposed. • Temperature dependence of thermal energy and momentum transfer CDFs is studied. • Functional fits are found to the data using a regression analysis. • Fits can construct the CDFs at any temperature at thermal energies. • Storage of fitting coefficients is much less than the current ACE data. - Abstract: Temperature can strongly affect the probabilities of certain neutron interactions (fission, capture, scattering, etc.) with materials. These probabilities are referred to in the nuclear community as ‘cross sections’ and are used as inputs for computer simulations. During the lifetime of a nuclear reactor, the core and its surrounding materials will experience a wide range of temperatures. To simulate the neutronic behavior in a realistic core, it is required to pre-store a large amount of cross section data to encompass the entire temperature range a neutron may experience. In recent years, methods have been developed to reduce data storage and obtain the cross section at the desired temperature ‘on-the-fly’ during radiation transport simulations using Monte Carlo codes. At thermal energies, however, the scattering of neutrons is complicated by their relatively small wavelengths, making molecular binding and lattice effects significant. Current approaches typically require nuclear data file sizes of tens to hundreds of MB per temperature, which can be prohibitive for realistic reactor physics simulations. To reduce the storage burden, a fitting approach in temperature is investigated that allows for the efficient evaluation of the thermal neutron scattering physics at an arbitrary temperature within a predefined range. The physics for thermal neutron scattering in graphite and hydrogen in water are evaluated with this approach. In both cases, the functional fits are able to accurately reproduce the scattering probabilities. The data storage for the fitting

  20. Monte Carlo analysis of radiative transport in oceanographic lidar measurements

    Energy Technology Data Exchange (ETDEWEB)

    Cupini, E.; Ferro, G. [ENEA, Divisione Fisica Applicata, Centro Ricerche Ezio Clementel, Bologna (Italy); Ferrari, N. [Bologna Univ., Bologna (Italy). Dipt. Ingegneria Energetica, Nucleare e del Controllo Ambientale

    2001-07-01

    The analysis of oceanographic lidar systems measurements is often carried out with semi-empirical methods, since there is only a rough understanding of the effects of many environmental variables. The development of techniques for interpreting the accuracy of lidar measurements is needed to evaluate the effects of various environmental situations, as well as of different experimental geometric configurations and boundary conditions. A Monte Carlo simulation model represents a tool that is particularly well suited for answering these important questions. The PREMAR-2F Monte Carlo code has been developed taking into account the main molecular and non-molecular components of the marine environment. The laser radiation interaction processes of diffusion, re-emission, refraction and absorption are treated. In particular are considered: the Rayleigh elastic scattering, produced by atoms and molecules with small dimensions with respect to the laser emission wavelength (i.e. water molecules), the Mie elastic scattering, arising from atoms or molecules with dimensions comparable to the laser wavelength (hydrosols), the Raman inelastic scattering, typical of water, the absorption of water, inorganic (sediments) and organic (phytoplankton and CDOM) hydrosols, the fluorescence re-emission of chlorophyll and yellow substances. PREMAR-2F is an extension of a code for the simulation of the radiative transport in atmospheric environments (PREMAR-2). The approach followed in PREMAR-2 was to combine conventional Monte Carlo techniques with analytical estimates of the probability of the receiver to have a contribution from photons coming back after an interaction in the field of view of the lidar fluorosensor collecting apparatus. This offers an effective mean for modelling a lidar system with realistic geometric constraints. The retrieved semianalytic Monte Carlo radiative transfer model has been developed in the frame of the Italian Research Program for Antarctica (PNRA) and it is

  1. Verification of Monte Carlo Calculations by Means of Neutron and Gamma Fluence Spectra Measurements behind and inside of Iron-Water Configurations

    International Nuclear Information System (INIS)

    Neutron and gamma spectra were measured behind and inside of modules consisting of variable iron and water slabs that were installed in radial beams of the zero-power training and research reactors AKR of the Technical University Dresden and ZLFR of the University of Applied Sciences Zittau/Goerlitz. The applied NE-213 scintillation spectrometer did allow the measurement of gamma and neutron fluence spectra in the energy regions 0.3-10 MeV for photons and 1.0-20 MeV for neutrons. The paper describes the experiments and presents important results of the measurements. They are compared with the results of Monte Carlo transport calculations made by means of the codes MCNP and TRAMO on an absolute scale of fluences

  2. Monte Carlo Calculation for Landmine Detection using Prompt Gamma Neutron Activation Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Park, Seungil; Kim, Seong Bong; Yoo, Suk Jae [Plasma Technology Research Center, Gunsan (Korea, Republic of); Shin, Sung Gyun; Cho, Moohyun [POSTECH, Pohang (Korea, Republic of); Han, Seunghoon; Lim, Byeongok [Samsung Thales, Yongin (Korea, Republic of)

    2014-05-15

    Identification and demining of landmines are a very important issue for the safety of the people and the economic development. To solve the issue, several methods have been proposed in the past. In Korea, National Fusion Research Institute (NFRI) is developing a landmine detector using prompt gamma neutron activation analysis (PGNAA) as a part of the complex sensor-based landmine detection system. In this paper, the Monte Carlo calculation results for this system are presented. Monte Carlo calculation was carried out for the design of the landmine detector using PGNAA. To consider the soil effect, average soil composition is analyzed and applied to the calculation. This results has been used to determine the specification of the landmine detector.

  3. Temperature variance study in Monte-Carlo photon transport theory

    International Nuclear Information System (INIS)

    We study different Monte-Carlo methods for solving radiative transfer problems, and particularly Fleck's Monte-Carlo method. We first give the different time-discretization schemes and the corresponding stability criteria. Then we write the temperature variance as a function of the variances of temperature and absorbed energy at the previous time step. Finally we obtain some stability criteria for the Monte-Carlo method in the stationary case

  4. A generic algorithm for Monte Carlo simulation of proton transport

    Science.gov (United States)

    Salvat, Francesc

    2013-12-01

    A mixed (class II) algorithm for Monte Carlo simulation of the transport of protons, and other heavy charged particles, in matter is presented. The emphasis is on the electromagnetic interactions (elastic and inelastic collisions) which are simulated using strategies similar to those employed in the electron-photon code PENELOPE. Elastic collisions are described in terms of numerical differential cross sections (DCSs) in the center-of-mass frame, calculated from the eikonal approximation with the Dirac-Hartree-Fock-Slater atomic potential. The polar scattering angle is sampled by employing an adaptive numerical algorithm which allows control of interpolation errors. The energy transferred to the recoiling target atoms (nuclear stopping) is consistently described by transformation to the laboratory frame. Inelastic collisions are simulated from DCSs based on the plane-wave Born approximation (PWBA), making use of the Sternheimer-Liljequist model of the generalized oscillator strength, with parameters adjusted to reproduce (1) the electronic stopping power read from the input file, and (2) the total cross sections for impact ionization of inner subshells. The latter were calculated from the PWBA including screening and Coulomb corrections. This approach provides quite a realistic description of the energy-loss distribution in single collisions, and of the emission of X-rays induced by proton impact. The simulation algorithm can be readily modified to include nuclear reactions, when the corresponding cross sections and emission probabilities are available, and bremsstrahlung emission.

  5. Calibration of a neutron moisture gauge by Monte-Carlo simulation

    International Nuclear Information System (INIS)

    Neutron transport calculations using the MCNP code have been used to determine flux distributions in soils and to derive the calibration curves of a neutron guage. The calculations were carried out for a typical geometry identical with that of the moisture guage HUMITERRA developed by the Laboratorio Nacional de Engenharia e Tecnologia Industrial, Portugal. To test the reliability of the method a comparison of computed and experimental results was made. The effect on the guage calibration curve of varying the values of several parameters which characterize the measurement system was studied, namely the soil dry bulk density, the active length of the neutron detector, the materials and wall thickness of the probe casing and of the access tubes. The usefulness of the method in the design, development and calibration of neutron guages for soil moisture determinations is discussed. (Author)

  6. UPWIND DISCONTINUOUS GALERKIN METHODS FOR TWO DIMENSIONAL NEUTRON TRANSPORT EQUATIONS

    Institute of Scientific and Technical Information of China (English)

    袁光伟; 沈智军; 闫伟

    2003-01-01

    In this paper the upwind discontinuous Galerkin methods with triangle meshes for two dimensional neutron transport equations will be studied.The stability for both of the semi-discrete and full-discrete method will be proved.

  7. MCMini: Monte Carlo on GPGPU

    Energy Technology Data Exchange (ETDEWEB)

    Marcus, Ryan C. [Los Alamos National Laboratory

    2012-07-25

    MCMini is a proof of concept that demonstrates the possibility for Monte Carlo neutron transport using OpenCL with a focus on performance. This implementation, written in C, shows that tracing particles and calculating reactions on a 3D mesh can be done in a highly scalable fashion. These results demonstrate a potential path forward for MCNP or other Monte Carlo codes.

  8. Monte Carlo simulation optimisation of zinc sulphide based fast-neutron detector for radiography using a 252Cf source

    Science.gov (United States)

    Meshkian, Mohsen

    2016-02-01

    Neutron radiography is rapidly extending as one of the methods for non-destructive screening of materials. There are various parameters to be studied for optimising imaging screens and image quality for different fast-neutron radiography systems. Herein, a Geant4 Monte Carlo simulation is employed to evaluate the response of a fast-neutron radiography system using a 252Cf neutron source. The neutron radiography system is comprised of a moderator as the neutron-to-proton converter with suspended silver-activated zinc sulphide (ZnS(Ag)) as the phosphor material. The neutron-induced protons deposit energy in the phosphor which consequently emits scintillation light. Further, radiographs are obtained by simulating the overall radiography system including source and sample. Two different standard samples are used to evaluate the quality of the radiographs.

  9. Monte Carlo simulation for the calibration of neutron source strength measurement of JT-60 upgrade

    International Nuclear Information System (INIS)

    The calibration of the relation between the neutron source strength in the whole plasma and the output of neutron monitor is important to evaluate the fusion gain in tokamaks with DD or DT operation. JT-60 will be modified to be tokamak of deuterium plasma with Ip≤7MA and V≤110 m3. The source strength of JT-60 Upgrade will be measured with 235U and 238U fission chambers. Detection efficiencies for source neutron are calculated by the Monte Carlo code MCNP with 3-dimensional modelling of JT-60 Upgrade and with the poloidally distributed neutron source. More than 90% of fission chamber's counts are contributed by source of -85deg235U and 238U detectors, respectively. Detection efficiencies are sensitive to major radius of the detector position, but not so sensitive to vertical and toroidal shift of the detector positions. And total uncertainties combined detector position errors are ±13% and ±9% for 235U and 238U detectors, respectively. The modelling errors of the detection efficiencies are so large for the 238U detector that more precise modelling including the port boxes is needed. (author)

  10. Adjoint electron-photon transport Monte Carlo calculations with ITS

    International Nuclear Information System (INIS)

    A general adjoint coupled electron-photon Monte Carlo code for solving the Boltzmann-Fokker-Planck equation has recently been created. It is a modified version of ITS 3.0, a coupled electronphoton Monte Carlo code that has world-wide distribution. The applicability of the new code to radiation-interaction problems of the type found in space environments is demonstrated

  11. Monte Carlo modeling and analyses of YALINA- booster subcritical assembly Part II : pulsed neutron source.

    Energy Technology Data Exchange (ETDEWEB)

    Talamo, A.; Gohar, M. Y. A.; Rabiti, C.; Nuclear Engineering Division

    2008-10-22

    One of the most reliable experimental methods for measuring the kinetic parameters of a subcritical assembly is the Sjoestrand method applied to the reaction rate generated from a pulsed neutron source. This study developed a new analytical methodology for characterizing the kinetic parameters of a subcritical assembly using the Sjoestrand method, which allows comparing the analytical and experimental time dependent reaction rates and the reactivity measurements. In this methodology, the reaction rate, detector response, is calculated due to a single neutron pulse using MCNP/MCNPX computer code or any other neutron transport code that explicitly simulates the fission delayed neutrons. The calculation simulates a single neutron pulse over a long time period until the delayed neutron contribution to the reaction is vanished. The obtained reaction rate is superimposed to itself, with respect to the time, to simulate the repeated pulse operation until the asymptotic level of the reaction rate, set by the delayed neutrons, is achieved. The superimposition of the pulse to itself was calculated by a simple C computer program. A parallel version of the C program is used due to the large amount of data being processed, e.g. by the Message Passing Interface (MPI). The new calculation methodology has shown an excellent agreement with the experimental results available from the YALINA-Booster facility of Belarus. The facility has been driven by a Deuterium-Deuterium or Deuterium-Tritium pulsed neutron source and the (n,p) reaction rate has been experimentally measured by a {sup 3}He detector. The MCNP calculation has utilized the weight window and delayed neutron biasing variance reduction techniques since the detector volume is small compared to the assembly volume. Finally, this methodology was used to calculate the IAEA benchmark of the YALINA-Booster experiment.

  12. Scattered Neutron Tomography Based on A Neutron Transport Inverse Problem

    Energy Technology Data Exchange (ETDEWEB)

    William Charlton

    2007-07-01

    Neutron radiography and computed tomography are commonly used techniques to non-destructively examine materials. Tomography refers to the cross-sectional imaging of an object from either transmission or reflection data collected by illuminating the object from many different directions.

  13. Evaluation of HYLIFE-II and Sombrero using 175- and 566-group neutron transport and activation cross sections

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, Jeffery F. E-mail: latkowski1@llnl.gov; Cullen, Dermott E.; Sanz, Javier

    2000-11-01

    Recent modifications to the TART Monte Carlo neutron and photon transport code allow enable calculation of 566-group neutron spectra. This expanded group structure represents a significant improvement over the 50- and 175-group structures that have been previously available. To support use of this new capability, neutron activation cross-section libraries have been created in the 175- and 566-group structures starting from the FENDL/A-2.0 pointwise data. Neutron spectra have been calculated for the first walls of the HYLIFE-II and Sombrero inertial fusion energy power plant designs and have been used in subsequent neutron activation calculations. The results obtained using the two different group structures are compared with each other as well as to those obtained using a 175-group version of the EAF3.1 activation cross-section library.

  14. Sensitive and transportable gadolinium-core plastic scintillator sphere for neutron detection and counting

    Science.gov (United States)

    Dumazert, Jonathan; Coulon, Romain; Carrel, Frédérick; Corre, Gwenolé; Normand, Stéphane; Méchin, Laurence; Hamel, Matthieu

    2016-08-01

    Neutron detection forms a critical branch of nuclear-related issues, currently driven by the search for competitive alternative technologies to neutron counters based on the helium-3 isotope. The deployment of plastic scintillators shows a high potential for efficient detectors, safer and more reliable than liquids, more easily scalable and cost-effective than inorganic. In the meantime, natural gadolinium, through its 155 and mostly 157 isotopes, presents an exceptionally high interaction probability with thermal neutrons. This paper introduces a dual system including a metal gadolinium core inserted at the center of a high-scale plastic scintillator sphere. Incident fast neutrons are thermalized by the scintillator shell and then may be captured with a significant probability by gadolinium 155 and 157 nuclei in the core. The deposition of a sufficient fraction of the capture high-energy prompt gamma signature inside the scintillator shell will then allow discrimination from background radiations by energy threshold, and therefore neutron detection. The scaling of the system with the Monte Carlo MCNPX2.7 code was carried out according to a tradeoff between the moderation of incident fast neutrons and the probability of slow neutron capture by a moderate-cost metal gadolinium core. Based on the parameters extracted from simulation, a first laboratory prototype for the assessment of the detection method principle has been synthetized. The robustness and sensitivity of the neutron detection principle are then assessed by counting measurement experiments. Experimental results confirm the potential for a stable, highly sensitive, transportable and cost-efficient neutron detector and orientate future investigation toward promising axes.

  15. Assessment of radiation shield integrity of DD/DT fusion neutron generator facilities by Monte Carlo and experimental methods

    International Nuclear Information System (INIS)

    DD/DT fusion neutron generators are used as sources of 2.5 MeV/14.1 MeV neutrons in experimental laboratories for various applications. Detailed knowledge of the radiation dose rates around the neutron generators are essential for ensuring radiological protection of the personnel involved with the operation. This work describes the experimental and Monte Carlo studies carried out in the Purnima Neutron Generator facility of the Bhabha Atomic Research Center (BARC), Mumbai. Verification and validation of the shielding adequacy was carried out by measuring the neutron and gamma dose-rates at various locations inside and outside the neutron generator hall during different operational conditions both for 2.5-MeV and 14.1-MeV neutrons and comparing with theoretical simulations. The calculated and experimental dose rates were found to agree with a maximum deviation of 20% at certain locations. This study has served in benchmarking the Monte Carlo simulation methods adopted for shield design of such facilities. This has also helped in augmenting the existing shield thickness to reduce the neutron and associated gamma dose rates for radiological protection of personnel during operation of the generators at higher source neutron yields up to 1 × 1010 n/s

  16. Assessment of radiation shield integrity of DD/DT fusion neutron generator facilities by Monte Carlo and experimental methods

    Science.gov (United States)

    Srinivasan, P.; Priya, S.; Patel, Tarun; Gopalakrishnan, R. K.; Sharma, D. N.

    2015-01-01

    DD/DT fusion neutron generators are used as sources of 2.5 MeV/14.1 MeV neutrons in experimental laboratories for various applications. Detailed knowledge of the radiation dose rates around the neutron generators are essential for ensuring radiological protection of the personnel involved with the operation. This work describes the experimental and Monte Carlo studies carried out in the Purnima Neutron Generator facility of the Bhabha Atomic Research Center (BARC), Mumbai. Verification and validation of the shielding adequacy was carried out by measuring the neutron and gamma dose-rates at various locations inside and outside the neutron generator hall during different operational conditions both for 2.5-MeV and 14.1-MeV neutrons and comparing with theoretical simulations. The calculated and experimental dose rates were found to agree with a maximum deviation of 20% at certain locations. This study has served in benchmarking the Monte Carlo simulation methods adopted for shield design of such facilities. This has also helped in augmenting the existing shield thickness to reduce the neutron and associated gamma dose rates for radiological protection of personnel during operation of the generators at higher source neutron yields up to 1 × 1010 n/s.

  17. Monte Carlo evaluation of the neutron detection efficiency of a superheated drop detector

    Energy Technology Data Exchange (ETDEWEB)

    Gualdrini, G.F. [ENEA, Centro Ricerche `Ezio Clementel`, Bologna (Italy). Dipt. Ambiente; D`Errico, F.; Noccioni, P. [Pisa, Univ. (Italy). Dipt. di Costruzioni Meccaniche e Nucleari

    1997-03-01

    Neuron dosimetry has recently gained renewed attention, following concerns on the exposure of crew members on board aircraft, and of workers around the increasing number of high energy accelerators for medical and research purpose. At the same time the new operational qualities for radiation dosimetry introduced by ICRU and the ICRP, aiming at a unified metrological system applicable to all types of radiation exposure, involved the need to update current devices in order to meet new requirements. Superheated Drop (Bubble) Detectors (SDD) offer an alternative approach to neutron radiation protection dosimetry. The SDDs are currently studied within a large collaborative effort involving Yale University. New Haven CT, Pisa (IT) University, the Physikalisch-Technische Bundesanstalt, Braunschweig D, and ENEA (Italian National Agency for new Technologies Energy and the Environment) Centre of Bologna. The detectors were characterised through calibrations with monoenergetic neutron beams and where experimental investigations were inadequate or impossible, such as in the intermediate energy range , parametric Monte Carlo calculations of the response were carried out. This report describes the general characteristic of the SDDs along with the Monte Carlo computations of the energy response and a comparison with the experimental results.

  18. Monte Carlo evaluation of the neutron detection efficiency of a superheated drop detector

    International Nuclear Information System (INIS)

    Neuron dosimetry has recently gained renewed attention, following concerns on the exposure of crew members on board aircraft, and of workers around the increasing number of high energy accelerators for medical and research purpose. At the same time the new operational qualities for radiation dosimetry introduced by ICRU and the ICRP, aiming at a unified metrological system applicable to all types of radiation exposure, involved the need to update current devices in order to meet new requirements. Superheated Drop (Bubble) Detectors (SDD) offer an alternative approach to neutron radiation protection dosimetry. The SDDs are currently studied within a large collaborative effort involving Yale University. New Haven CT, Pisa (IT) University, the Physikalisch-Technische Bundesanstalt, Braunschweig D, and ENEA (Italian National Agency for new Technologies Energy and the Environment) Centre of Bologna. The detectors were characterised through calibrations with monoenergetic neutron beams and where experimental investigations were inadequate or impossible, such as in the intermediate energy range , parametric Monte Carlo calculations of the response were carried out. This report describes the general characteristic of the SDDs along with the Monte Carlo computations of the energy response and a comparison with the experimental results

  19. Exact modeling of the torus geometry with Monte Carlo transport code

    International Nuclear Information System (INIS)

    It is valuable to model torus geometry exactry for the neutronics design of fusion reactor in order to assess neutronics characteristics such as tritium breeding ratio, heat generation rate, etc, near the plasma. Monte Carlo code MORSE-GG which plays important role in the radiation streaming calculation of fusion reactors had been able to deal with the geometry composed of second order surfaces. The MORSE-GG program is modified to be able to deal with torus geometry which has fourth order surface by solving biquadratic equations, hoping that MORSE-GG code becomes more effective for the neutronics calculation of the Tokamak fusion reactor. (author)

  20. Tomographic image of prompt gamma ray from boron neutron capture therapy: A Monte Carlo simulation study

    International Nuclear Information System (INIS)

    The resulting neutron captures in 10B are used for radiation therapy. The occurrence point of the characteristic 478 keV prompt gamma rays agrees with the neutron capture point. If these prompt gamma rays are detected by external instruments such as a gamma camera or single photon emission computed tomography (SPECT), the therapy region can be monitored during the treatment using images. A feasibility study and analysis of a reconstructed image using many projections (128) were conducted. The optimization of the detection system and a detailed neutron generator simulation were beyond the scope of this study. The possibility of extracting a 3D BNCT-SPECT image was confirmed using the Monte Carlo simulation and OSEM algorithm. The quality of the prompt gamma ray SPECT image obtained from BNCT was evaluated quantitatively using three different boron uptake regions and was shown to depend on the location and size relations. The prospects for obtaining an actual BNCT-SPECT image were also estimated from the quality of the simulated image and the simulation conditions. When multi tumor regions should be treated using the BNCT method, a reasonable model to determine how many useful images can be obtained from SPECT can be provided to the BNCT facilities based on the preceding imaging research. However, because the scope of this research was limited to checking the feasibility of 3D BNCT-SPECT image reconstruction using multiple projections, along with an evaluation of the image, some simulation conditions were taken from previous studies. In the future, a simulation will be conducted that includes optimized conditions for an actual BNCT facility, along with an imaging process for motion correction in BNCT. Although an excessively long simulation time was required to obtain enough events for image reconstruction, the feasibility of acquiring a 3D BNCT-SPECT image using multiple projections was confirmed using a Monte Carlo simulation, and a quantitative image analysis was

  1. Calculating the effective delayed neutron fraction in the Molten Salt Fast Reactor: Analytical, deterministic and Monte Carlo approaches

    International Nuclear Information System (INIS)

    Highlights: • Calculation of effective delayed neutron fraction in circulating-fuel reactors. • Extension of the Monte Carlo SERPENT-2 code for delayed neutron precursor tracking. • Forward and adjoint multi-group diffusion eigenvalue problems in OpenFOAM. • Analytical approach for βeff calculation in simple geometries and flow conditions. • Good agreement among the three proposed approaches in the MSFR test-case. - Abstract: This paper deals with the calculation of the effective delayed neutron fraction (βeff) in circulating-fuel nuclear reactors. The Molten Salt Fast Reactor is adopted as test case for the comparison of the analytical, deterministic and Monte Carlo methods presented. The Monte Carlo code SERPENT-2 has been extended to allow for delayed neutron precursors drift, according to the fuel velocity field. The forward and adjoint eigenvalue multi-group diffusion problems are implemented and solved adopting the multi-physics tool-kit OpenFOAM, by taking into account the convective and turbulent diffusive terms in the precursors balance. These two approaches show good agreement in the whole range of the MSFR operating conditions. An analytical formula for the circulating-to-static conditions βeff correction factor is also derived under simple hypotheses, which explicitly takes into account the spatial dependence of the neutron importance. Its accuracy is assessed against Monte Carlo and deterministic results. The effects of in-core recirculation vortex and turbulent diffusion are finally analysed and discussed

  2. Transport coefficients in superfluid neutron stars

    CERN Document Server

    Tolos, Laura; Sarkar, Sreemoyee; Tarrus, Jaume

    2014-01-01

    We study the shear and bulk viscosity coefficients as well as the thermal conductivity as arising from the collisions among phonons in superfluid neutron stars. We use effective field theory techniques to extract the allowed phonon collisional processes, written as a function of the equation of state and the gap of the system. The shear viscosity due to phonon scattering is compared to calculations of that coming from electron collisions. We also comment on the possible consequences for r-mode damping in superfluid neutron stars. Moreover, we find that phonon collisions give the leading contribution to the bulk viscosities in the core of the neutron stars. We finally obtain a temperature-independent thermal conductivity from phonon collisions and compare it with the electron-muon thermal conductivity in superfluid neutron stars.

  3. Transport coefficients in superfluid neutron stars

    Energy Technology Data Exchange (ETDEWEB)

    Tolos, Laura [Instituto de Ciencias del Espacio (IEEC/CSIC) Campus Universitat Autònoma de Barcelona, Facultat de Ciències, Torre C5, E-08193 Bellaterra (Barcelona) (Spain); Frankfurt Institute for Advances Studies. Johann Wolfgang Goethe University, Ruth-Moufang-Str. 1, 60438 Frankfurt am Main (Germany); Manuel, Cristina [Instituto de Ciencias del Espacio (IEEC/CSIC) Campus Universitat Autònoma de Barcelona, Facultat de Ciències, Torre C5, E-08193 Bellaterra (Barcelona) (Spain); Sarkar, Sreemoyee [Tata Institute of Fundamental Research, Homi Bhaba Road, Mumbai-400005 (India); Tarrus, Jaume [Physik Department, Technische Universität München, D-85748 Garching (Germany)

    2016-01-22

    We study the shear and bulk viscosity coefficients as well as the thermal conductivity as arising from the collisions among phonons in superfluid neutron stars. We use effective field theory techniques to extract the allowed phonon collisional processes, written as a function of the equation of state and the gap of the system. The shear viscosity due to phonon scattering is compared to calculations of that coming from electron collisions. We also comment on the possible consequences for r-mode damping in superfluid neutron stars. Moreover, we find that phonon collisions give the leading contribution to the bulk viscosities in the core of the neutron stars. We finally obtain a temperature-independent thermal conductivity from phonon collisions and compare it with the electron-muon thermal conductivity in superfluid neutron stars.

  4. Development of Monte Carlo code for coincidence prompt gamma-ray neutron activation analysis

    Science.gov (United States)

    Han, Xiaogang

    Prompt Gamma-Ray Neutron Activation Analysis (PGNAA) offers a non-destructive, relatively rapid on-line method for determination of elemental composition of bulk and other samples. However, PGNAA has an inherently large background. These backgrounds are primarily due to the presence of the neutron excitation source. It also includes neutron activation of the detector and the prompt gamma rays from the structure materials of PGNAA devices. These large backgrounds limit the sensitivity and accuracy of PGNAA. Since most of the prompt gamma rays from the same element are emitted in coincidence, a possible approach for further improvement is to change the traditional PGNAA measurement technique and introduce the gamma-gamma coincidence technique. It is well known that the coincidence techniques can eliminate most of the interference backgrounds and improve the signal-to-noise ratio. A new Monte Carlo code, CEARCPG has been developed at CEAR to simulate gamma-gamma coincidence spectra in PGNAA experiment. Compared to the other existing Monte Carlo code CEARPGA I and CEARPGA II, a new algorithm of sampling the prompt gamma rays produced from neutron capture reaction and neutron inelastic scattering reaction, is developed in this work. All the prompt gamma rays are taken into account by using this new algorithm. Before this work, the commonly used method is to interpolate the prompt gamma rays from the pre-calculated gamma-ray table. This technique works fine for the single spectrum. However it limits the capability to simulate the coincidence spectrum. The new algorithm samples the prompt gamma rays from the nucleus excitation scheme. The primary nuclear data library used to sample the prompt gamma rays comes from ENSDF library. Three cases are simulated and the simulated results are benchmarked with experiments. The first case is the prototype for ETI PGNAA application. This case is designed to check the capability of CEARCPG for single spectrum simulation. The second

  5. Dosimetry and dose planning in boron neutron capture therapy : Monte Carlo studies

    Energy Technology Data Exchange (ETDEWEB)

    Koivunoro, H.

    2012-07-01

    Boron neutron capture therapy (BNCT) is a biologically targeted radiotherapy modality. So far, 249 cancer patients have received BNCT at the Finnish Research Reactor 1 (FiR 1) in Finland. The effectiveness and safety of radiotherapy are dependent on the radiation dose delivered to the tumor and healthy tissues, and on the accuracy of the doses. At FiR 1, patient dose calculations are performed with the Monte Carlo (MC) -based treatmentplanning system (TPS), Simulation Environment for Radiotherapy Applications (SERA). Initially, BNCT was applied to head and neck cancer, brain tumors, and malignant melanoma. To evaluate the applicability of the new target tumors for BNCT, calculation dosimetry studies are needed. So far, clinical BNCT has been performed with the neutrons from a nuclear reactor, while an accelerator based neutron sources applicable for hospital operation would be preferable. In this thesis, BNCT patient dose calculation practice in Finland was evaluated against reference calculations and experimental data in several cases. Calculations with two TPSs applied in clinical BNCT were compared. The suitability of the deuterium-deuterium (DD) and deuterium-tritium (D-T) fusion reaction-based compact neutron sources for BNCT were evaluated. In addition, feasibility of BNCT for noninvasive liver tumor treatments was examined. The deviation between SERA and the reference calculations was within 4% in the phantoms studied and in a brain cancer patient model elsewhere, except on the phantom or skin surface, for the boron, nitrogen, and photon dose components. These dose components produce 99% of the tumor dose and > 90% of the healthy tissue dose at points of relevance for treatment at the FiR 1 facility. The reduced voxel cell size ({<=} 0.5 cm) in the SERA edit mesh improved calculation accuracy on the surface. The erratic biased fastneutron run option in SERA led to significant underestimation (up to 30-60%) of the fastneutron dose, while more accurate fast-neutron

  6. A Monte Carlo simulation of a simplified reactor by decomposition of the neutron spectrum into fission, intermediate and thermal distributions

    Energy Technology Data Exchange (ETDEWEB)

    Barcellos, Luiz Felipe F.C.; Bodmann, Bardo E.J.; Vilhena, Marco T. de, E-mail: luizfelipe.fcb@gmail.com, E-mail: bardo.bodmann@ufrgs.br, E-mail: vilhena@mat.ufrgs.br [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre (Brazil). Grupo de Estudos Nucleares. Escola de Engenharia; Leite, Sergio Q. Bogado, E-mail: sbogado@eletronuclear.gov.br [Eletrobras Termonuclear S.A. (ELETRONUCLEAR), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    In this paper the neutron spectrum of a simulated hypothetical nuclear reactor is decomposed as a sum of three probability distributions. Two of the distributions preserve shape with time but not necessarily the integral. One of the two distributions is due to fission, i.e. high neutron energies and the second a Maxwell-Boltzmann distribution for low (thermal) neutron energies. The third distribution has an a priori unknown and possibly variable shape with time and is determined from parametrizations of Monte Carlo simulation. This procedure is effective in attaining two objectives, the first is to include effects due to up-scattering of neutrons, and the second is to optimize computational time of the stochastic method (tracking and interaction). The simulation of the reactor is done with a Monte Carlo computer code with tracking and using continuous energy dependence. This code so far computes down-scattering, but the computation of up-scattering was ignored, since it increases significantly computational processing time. In order to circumvent this problem, one may recognize that up-scattering is dominant towards the lower energy end of the spectrum, where we assume that thermal equilibrium conditions for neutrons immersed in their environment holds. The optimization may thus be achieved by calculating only the interaction rate for neutron energy gain as well as loss and ignoring tracking, i.e. up-scattering is 'simulated' by a statistical treatment of the neutron population. For the fission and the intermediate part of the neutron spectrum tracking is taken into account explicitly, where according to the criticality condition the integral of the fission spectrum may depend on time. This simulation is performed using continuous energy dependence, and as a rst case to be studied we assume a recurrent regime. The three calculated distributions are then used in the Monte Carlo code to compute the subsequent Monte Carlo steps with subsequent updates

  7. Monte-Carlo simulation of an ultra small-angle neutron scattering instrument based on Soller slits

    Energy Technology Data Exchange (ETDEWEB)

    Rieker, T. [Univ. of New Mexico, Albuquerque, NM (United States); Hubbard, P. [Sandia National Labs., Albuquerque, NM (United States)

    1997-09-01

    Monte Carlo simulations are used to investigate an ultra small-angle neutron scattering instrument for use at a pulsed source based on a Soller slit collimator and analyzer. The simulations show that for a q{sub min} of {approximately}le-4 {angstrom}{sup -1} (15 {angstrom} neutrons) a few tenths of a percent of the incident flux is transmitted through both collimators at q=0.

  8. Feasibility Study of Neutron Dose for Real Time Image Guided Proton Therapy: A Monte Carlo Study

    CERN Document Server

    Kim, Jin Sung; Kim, Daehyun; Shin, EunHyuk; Chung, Kwangzoo; Cho, Sungkoo; Ahn, Sung Hwan; Ju, Sanggyu; Chung, Yoonsun; Jung, Sang Hoon; Han, Youngyih

    2015-01-01

    Two full rotating gantry with different nozzles (Multipurpose nozzle with MLC, Scanning Dedicated nozzle) with conventional cyclotron system is installed and under commissioning for various proton treatment options at Samsung Medical Center in Korea. The purpose of this study is to investigate neutron dose equivalent per therapeutic dose, H/D, to x-ray imaging equipment under various treatment conditions with monte carlo simulation. At first, we investigated H/D with the various modifications of the beam line devices (Scattering, Scanning, Multi-leaf collimator, Aperture, Compensator) at isocenter, 20, 40, 60 cm distance from isocenter and compared with other research groups. Next, we investigated the neutron dose at x-ray equipments used for real time imaging with various treatment conditions. Our investigation showed the 0.07 ~ 0.19 mSv/Gy at x-ray imaging equipments according to various treatment options and intestingly 50% neutron dose reduction effect of flat panel detector was observed due to multi- lea...

  9. Construction of Monte Carlo operators in collisional transport theory

    International Nuclear Information System (INIS)

    A Monte Carlo approach for investigating the dynamics of quiescent collisional magnetoplasmas is presented, based on the discretization of the gyrokinetic equation. The theory applies to a strongly rotating multispecies plasma, in a toroidally axisymmetric configuration. Expressions of the Monte Carlo collision operators are obtained for general v-space nonorthogonal coordinates systems, in terms of approximate solutions of the discretized gyrokinetic equation. Basic features of the Monte Carlo operators are that they fullfill all the required conservation laws, i.e., linear momentum and kinetic energy conservation, and in addition that they take into account correctly also off-diagonal diffusion coefficients. The present operators are thus potentially useful for describing the dynamics of a multispecies toroidal magnetoplasma. In particular, strict ambipolarity of particle fluxes is ensured automatically in the limit of small departures of the unperturbed particle trajectories from some initial axisymmetric toroidal magnetic surfaces

  10. A fast Monte Carlo program for pulsed-neutron capture-gamma tools

    Energy Technology Data Exchange (ETDEWEB)

    Hovgaard, J.

    1992-02-01

    A fast model for the pulsed-neutron capture-gamma tool has been developed. It is believed that the program produce valid results even though some approximation have been introduced. A correct {gamma} photon transport simulation, which is under preparation, has for instance not yet been included. Simulations performed so far has shown that the model, with respect to computing time and accuracy, fully lives up to expectations with respect to computing time and accuracy. (au).

  11. A fast Monte Carlo program for pulsed-neutron capture-gamma tools

    Energy Technology Data Exchange (ETDEWEB)

    Hovgaard, J.

    1992-02-01

    A fast model for the pulsed-neutron capture-gamma tool has been developed. It is believed that the program produce valid results even though some approximation have been introduced. A correct [gamma] photon transport simulation, which is under preparation, has for instance not yet been included. Simulations performed so far has shown that the model, with respect to computing time and accuracy, fully lives up to expectations with respect to computing time and accuracy. (au).

  12. On generating neutron transport tables with the NJOY system

    Energy Technology Data Exchange (ETDEWEB)

    Caldeira, Alexandre D.; Claro, Luiz H., E-mail: alexdc@ieav.cta.br, E-mail: luizhenu@ieav.cta.br [Instituto de Estudos Avancados (IEAv), Sao Jose dos Campos, SP (Brazil)

    2013-07-01

    Incorrect values for the product of the average number of neutrons released per fission and the fission microscopic cross-section were detected in several energy groups of a neutron transport table generated with the most updated version of the NJOY system. It was verified that the problem persists when older versions of this system are utilized. Although this problem exists for, at least, ten years, it is still an open question. (author)

  13. Considerations in the design of an improved transportable neutron spectrometer

    CERN Document Server

    Williams, A M; Brushwood, J M; Beeley, P A

    2002-01-01

    The Transportable Neutron Spectrometer (TNS) has been used by the Ministry of Defence for over 15 years to characterise neutron fields in workplace environments and provide local correction factors for both area and personal dosimeters. In light of advances in neutron spectrometry, a programme to evaluate and improve TNS has been initiated. This paper describes TNS, presents its operation in known radioisotope fields and in a reactor environment. Deficiencies in the operation of the instrument are highlighted, together with proposals for updating the response functions and spectrum unfolding methodologies.

  14. A method for simulating real-time neutron populations, materials and geometries using the GEANT4 Monte Carlo toolkit

    International Nuclear Information System (INIS)

    GEANT4 is a Monte Carlo particle physics toolkit that simulates elementary particles moving through matter. GEANT4 allows a population of neutrons to be tracked in a multiplying medium as the population and the medium evolve. However, the population must be artificially stabilized so that it neither explodes nor vanishes. We present a stabilization method where the simulation is divided into short time intervals and the population is renormalized at the end of each interval. This method was used with a simple sphere of U235 to calculate the effective neutron multiplication factor (keff) from the continuous evolution of the neutron population. (author)

  15. Verification of Monte Carlo calculations of the neutron flux in typical irradiation channels of the TRIGA reactor, Ljubljana

    NARCIS (Netherlands)

    Jacimovic, R; Maucec, M; Trkov, A

    2003-01-01

    An experimental verification of Monte Carlo neutron flux calculations in typical irradiation channels in the TRIGA Mark II reactor at the Jozef Stefan Institute is presented. It was found that the flux, as well as its spectral characteristics, depends rather strongly on the position of the irradiati

  16. Estimates of neutron leakage through penetrations of the CERN intersecting storage rings by Monte Carlo albedo calculations

    CERN Document Server

    Routti, J T

    1975-01-01

    The monokinetic and multigroup Monte Carlo albedo methods applicable to estimating neutron leakage through penetrations in the shielding of high-energy accelerators are reviewed. They are used to calculate attenuation factors and dose levels in the tunnels of the CERN intersecting storage rings. (28 refs).

  17. Corrigendum to "Monte Carlo simulations of the secondary neutron ambient and effective dose equivalent rates from surface to suborbital altitudes and low Earth orbit"

    Science.gov (United States)

    El-Jaby, Samy

    2016-06-01

    A recent paper published in Life Sciences in Space Research (El-Jaby and Richardson, 2015) presented estimates of the secondary neutron ambient and effective dose equivalent rates, in air, from surface altitudes up to suborbital altitudes and low Earth orbit. These estimates were based on MCNPX (LANL, 2011) (Monte Carlo N-Particle eXtended) radiation transport simulations of galactic cosmic radiation passing through Earth's atmosphere. During a recent review of the input decks used for these simulations, a systematic error was discovered that is addressed here. After reassessment, the neutron ambient and effective dose equivalent rates estimated are found to be 10 to 15% different, though, the essence of the conclusions drawn remains unchanged.

  18. Calculated characteristics of subcritical assembly with anisotropic transport of neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Gorin, N.V.; Lipilina, E.N.; Lyutov, V.D.; Saukov, A.I. [Zababakhin Russian Federal Nuclear Center - All-Russian Scientific Researching Institute of Technical Physics (Russian Federation)

    2003-07-01

    There was considered possibility of creating enough sub-critical system that multiply neutron fluence from a primary source by many orders. For assemblies with high neutron tie between parts, it is impossible. That is why there was developed a construction consisting of many units (cascades) having weak feedback with preceding cascades. The feedback attenuation was obtained placing layers of slow neutron absorber and moderators between the cascades of fission material. Anisotropy of fast neutron transport through the layers was used. The system consisted of many identical cascades aligning one by another. Each cascade consists of layers of moderator, fissile material and absorber of slow neutrons. The calculations were carried out using the code MCNP.4a with nuclear data library ENDF/B5. In this construction neutrons spread predominantly in one direction multiplying in each next fissile layer, and they attenuate considerably in the opposite direction. In a calculated construction, multiplication factor of one cascade is about 1.5 and multiplication factor of whole construction composed of n cascades is 1.5{sup n}. Calculated keff value is 0.9 for one cascade and does not exceed 0.98 for a system containing any number of cascades. Therefore the assembly is always sub-critical and therefore it is safe in respect of criticality. There was considered using such a sub-critical assembly to create a powerful neutron fluence for neutron boron-capturing therapy. The system merits and demerits were discussed. (authors)

  19. Monte-Carlo method for studying the slowing down of neutrons in a thin plate of hydrogenated matter

    International Nuclear Information System (INIS)

    The studies of interaction of slow neutrons with atomic nuclei by means of the time of flight methods are made with a pulsed neutron source with a broad energy spectrum. The measurement accuracy needs a high intensity and an output time as short as possible and well defined. If the neutrons source is a target bombarded by the beam of a pulsed accelerator, it is usually required to slow down the neutrons to obtain a sufficient intensity at low energies. The purpose of the Monte-Carlo method which is described in this paper is to study the slowing down properties, mainly the intensity and the output time distribution of the slowed-down neutrons. The choice of the method and parameters studied is explained as well as the principles, some calculations and the program organization. A few results given as examples were obtained in the line of this program, the limits of which are principally due to simplifying physical hypotheses. (author)

  20. Improvement of the neutron flux calculations in thick shield by conditional Monte Carlo and deterministic methods

    Energy Technology Data Exchange (ETDEWEB)

    Ghassoun, Jillali; Jehoauni, Abdellatif [Nuclear physics and Techniques Lab., Faculty of Science, Semlalia, Marrakech (Morocco)

    2000-01-01

    In practice, the estimation of the flux obtained by Fredholm integral equation needs a truncation of the Neuman series. The order N of the truncation must be large in order to get a good estimation. But a large N induces a very large computation time. So the conditional Monte Carlo method is used to reduce time without affecting the estimation quality. In a previous works, in order to have rapid convergence of calculations it was considered only weakly diffusing media so that has permitted to truncate the Neuman series after an order of 20 terms. But in the most practical shields, such as water, graphite and beryllium the scattering probability is high and if we truncate the series at 20 terms we get bad estimation of flux, so it becomes useful to use high orders in order to have good estimation. We suggest two simple techniques based on the conditional Monte Carlo. We have proposed a simple density of sampling the steps for the random walk. Also a modified stretching factor density depending on a biasing parameter which affects the sample vector by stretching or shrinking the original random walk in order to have a chain that ends at a given point of interest. Also we obtained a simple empirical formula which gives the neutron flux for a medium characterized by only their scattering probabilities. The results are compared to the exact analytic solution, we have got a good agreement of results with a good acceleration of convergence calculations. (author)

  1. Improvement of the neutron flux calculations in thick shield by conditional Monte Carlo and deterministic methods

    International Nuclear Information System (INIS)

    In practice, the estimation of the flux obtained by Fredholm integral equation needs a truncation of the Neuman series. The order N of the truncation must be large in order to get a good estimation. But a large N induces a very large computation time. So the conditional Monte Carlo method is used to reduce time without affecting the estimation quality. In a previous works, in order to have rapid convergence of calculations it was considered only weakly diffusing media so that has permitted to truncate the Neuman series after an order of 20 terms. But in the most practical shields, such as water, graphite and beryllium the scattering probability is high and if we truncate the series at 20 terms we get bad estimation of flux, so it becomes useful to use high orders in order to have good estimation. We suggest two simple techniques based on the conditional Monte Carlo. We have proposed a simple density of sampling the steps for the random walk. Also a modified stretching factor density depending on a biasing parameter which affects the sample vector by stretching or shrinking the original random walk in order to have a chain that ends at a given point of interest. Also we obtained a simple empirical formula which gives the neutron flux for a medium characterized by only their scattering probabilities. The results are compared to the exact analytic solution, we have got a good agreement of results with a good acceleration of convergence calculations. (author)

  2. Neutronic Analysis of the 3 MW TRIGA MARK II Research Reactor, Part I: Monte Carlo Simulation

    International Nuclear Information System (INIS)

    This study deals with the neutronic analysis of the current core configuration of a 3 MW TRIGA MARK II research reactor at Atomic Energy Research Establishment (AERE), Savar, Dhaka, Bangladesh and validation of the results by benchmarking with the experimental, operational and available Final Safety Analysis Report (FSAR) values. The three-dimensional continuous-energy Monte Carlo code MCNP4C was used to develop a versatile and accurate full-core model of the TRIGA core. The model represents in detail all components of the core with literally no physical approximation. All fresh fuel and control elements as well as the vicinity of the core were precisely described. Continuous energy cross-section data from ENDF/B-VI and S(α, β) scattering functions from the ENDF/B-V library were used. The validation of the model against benchmark experimental results is presented. The MCNP predictions and the experimentally determined values are found to be in very good agreement, which indicates that the Monte Carlo model is correctly simulating the TRIGA reactor. (author)

  3. Advantages of Analytical Transformations in Monte Carlo Methods for Radiation Transport

    International Nuclear Information System (INIS)

    Monte Carlo methods for radiation transport typically attempt to solve an integral by directly sampling analog or weighted particles, which are treated as physical entities. Improvements to the methods involve better sampling, probability games or physical intuition about the problem. We show that significant improvements can be achieved by recasting the equations with an analytical transform to solve for new, non-physical entities or fields. This paper looks at one such transform, the difference formulation for thermal photon transport, showing a significant advantage for Monte Carlo solution of the equations for time dependent transport. Other related areas are discussed that may also realize significant benefits from similar analytical transformations

  4. Radiation Transport for Explosive Outflows: A Multigroup Hybrid Monte Carlo Method

    CERN Document Server

    Wollaeger, Ryan T; Graziani, Carlo; Couch, Sean M; Jordan, George C; Lamb, Donald Q; Moses, Gregory A

    2013-01-01

    We explore the application of Implicit Monte Carlo (IMC) and Discrete Diffusion Monte Carlo (DDMC) to radiation transport in strong fluid outflows with structured opacity. The IMC method of Fleck & Cummings is a stochastic computational technique for nonlinear radiation transport. IMC is partially implicit in time and may suffer in efficiency when tracking Monte Carlo particles through optically thick materials. The DDMC method of Densmore accelerates an IMC computation where the domain is diffusive. Recently, Abdikamalov extended IMC and DDMC to multigroup, velocity-dependent neutrino transport with the intent of modeling neutrino dynamics in core-collapse supernovae. Densmore has also formulated a multifrequency extension to the originally grey DDMC method. In this article we rigorously formulate IMC and DDMC over a high-velocity Lagrangian grid for possible application to photon transport in the post-explosion phase of Type Ia supernovae. The method described is suitable for a large variety of non-mono...

  5. Monte Carlo efficiency calibration of a neutron generator-based total-body irradiator

    International Nuclear Information System (INIS)

    Many body composition measurement systems are calibrated against a single-sized reference phantom. Prompt-gamma neutron activation (PGNA) provides the only direct measure of total body nitrogen (TBN), an index of the body's lean tissue mass. In PGNA systems, body size influences neutron flux attenuation, induced gamma signal distribution, and counting efficiency. Thus, calibration based on a single-sized phantom could result in inaccurate TBN values. We used Monte Carlo simulations (MCNP-5; Los Alamos National Laboratory) in order to map a system's response to the range of body weights (65-160 kg) and body fat distributions (25-60%) in obese humans. Calibration curves were constructed to derive body-size correction factors relative to a standard reference phantom, providing customized adjustments to account for differences in body habitus of obese adults. The use of MCNP-generated calibration curves should allow for a better estimate of the true changes in lean tissue mass that many occur during intervention programs focused only on weight loss. (author)

  6. Monte Carlo Studies of Charge Transport Below the Mobility Edge

    OpenAIRE

    Jakobsson, Mattias

    2012-01-01

    Charge transport below the mobility edge, where the charge carriers are hopping between localized electronic states, is the dominant charge transport mechanism in a wide range of disordered materials. This type of incoherent charge transport is fundamentally different from the coherent charge transport in ordered crystalline materials. With the advent of organic electronics, where small organic molecules or polymers replace traditional inorganic semiconductors, the interest for this type of h...

  7. Monte Carlo modelling of positron transport in real world applications

    International Nuclear Information System (INIS)

    Due to the unstable nature of positrons and their short lifetime, it is difficult to obtain high positron particle densities. This is why the Monte Carlo simulation technique, as a swarm method, is very suitable for modelling most of the current positron applications involving gaseous and liquid media. The ongoing work on the measurements of cross-sections for positron interactions with atoms and molecules and swarm calculations for positrons in gasses led to the establishment of good cross-section sets for positron interaction with gasses commonly used in real-world applications. Using the standard Monte Carlo technique and codes that can follow both low- (down to thermal energy) and high- (up to keV) energy particles, we are able to model different systems directly applicable to existing experimental setups and techniques. This paper reviews the results on modelling Surko-type positron buffer gas traps, application of the rotating wall technique and simulation of positron tracks in water vapor as a substitute for human tissue, and pinpoints the challenges in and advantages of applying Monte Carlo simulations to these systems.

  8. Monte Carlo modelling of positron transport in real world applications

    Science.gov (United States)

    Marjanović, S.; Banković, A.; Šuvakov, M.; Petrović, Z. Lj

    2014-05-01

    Due to the unstable nature of positrons and their short lifetime, it is difficult to obtain high positron particle densities. This is why the Monte Carlo simulation technique, as a swarm method, is very suitable for modelling most of the current positron applications involving gaseous and liquid media. The ongoing work on the measurements of cross-sections for positron interactions with atoms and molecules and swarm calculations for positrons in gasses led to the establishment of good cross-section sets for positron interaction with gasses commonly used in real-world applications. Using the standard Monte Carlo technique and codes that can follow both low- (down to thermal energy) and high- (up to keV) energy particles, we are able to model different systems directly applicable to existing experimental setups and techniques. This paper reviews the results on modelling Surko-type positron buffer gas traps, application of the rotating wall technique and simulation of positron tracks in water vapor as a substitute for human tissue, and pinpoints the challenges in and advantages of applying Monte Carlo simulations to these systems.

  9. Thermal and transport properties of the neutron star inner crust

    CERN Document Server

    Page, Dany

    2012-01-01

    We review the nuclear and condensed matter physics underlying the thermal and transport properties of the neutron star inner crust. These properties play a key role in interpreting transient phenomena such as thermal relaxation in accreting neutron stars, superbursts, and magnetar flares. We emphasize simplifications that occur at low temperature where the inner crust can be described in terms of electrons and collective excitations. The heat conductivity and heat capacity of the solid and superfluid phase of matter is discussed in detail and we emphasize its role in interpreting observations of neutron stars in soft X-ray transients. We highlight recent theoretical and observational results, and identify future work needed to better understand a host of transient phenomena in neutron stars.

  10. Optimized design of the nuclear fuel rod transport container used for non-destructive testing with neutron radiography

    International Nuclear Information System (INIS)

    Background: Working under extreme conditions, nuclear fuel rods, the key component of nuclear plants and reactors, are easy to be broken. In order to be safe in operation, lots of testing methods on the fuel rods have to be carried out from fabrication to operation. Purpose: Neutron radiography is a unique non-destructive testing technique which can be used to test samples with radioactivity. As the essential equipment, the nuclear fuel rod transport container has to shield the radioactivity of fuel rod and control its movement during testing and transporting. Methods: The shielding simulation of the transport container was performed using the MCNP4C code, which is a general purpose Monte Carlo code for calculating the time dependent multi-group energy transport equation for neutrons, photons and electrons in three dimensional geometries. Results: The material and dimension of the transport container used for neutron radiography testing fuel rods at Chinese Advanced Research Reactor (CARR) were optimally designed by MCNP, and the mechanical devices used to control fuel rods' movement were also described. Conclusion: The 2-m long fuel rod can be tested at CARR's neutron radiography facility (under construction) with this transport container. (authors)

  11. Monte Carlo analysis of the Neutron Standards Laboratory of the CIEMAT; Analisis Monte Carlo del Laboratorio de Patrones Neutronicos del CIEMAT

    Energy Technology Data Exchange (ETDEWEB)

    Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico); Mendez V, R. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas, Av. Complutense 40, 28040 Madrid (Spain); Guzman G, K. A., E-mail: fermineutron@yahoo.com [Universidad Politecnica de Madrid, Departamento de Ingenieria Nuclear, C. Jose Gutierrez Abascal 2, 28006 Madrid (Spain)

    2014-10-15

    By means of Monte Carlo methods was characterized the neutrons field produced by calibration sources in the Neutron Standards Laboratory of the Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT). The laboratory has two neutron calibration sources: {sup 241}AmBe and {sup 252}Cf which are stored in a water pool and are placed on the calibration bench using controlled systems at distance. To characterize the neutrons field was built a three-dimensional model of the room where it was included the stainless steel bench, the irradiation table and the storage pool. The sources model included double encapsulated of steel, as cladding. With the purpose of determining the effect that produces the presence of the different components of the room, during the characterization the neutrons spectra, the total flow and the rapidity of environmental equivalent dose to 100 cm of the source were considered. The presence of the walls, floor and ceiling of the room is causing the most modification in the spectra and the integral values of the flow and the rapidity of environmental equivalent dose. (Author)

  12. PyMercury: Interactive Python for the Mercury Monte Carlo Particle Transport Code

    International Nuclear Information System (INIS)

    Monte Carlo particle transport applications are often written in low-level languages (C/C++) for optimal performance on clusters and supercomputers. However, this development approach often sacrifices straightforward usability and testing in the interest of fast application performance. To improve usability, some high-performance computing applications employ mixed-language programming with high-level and low-level languages. In this study, we consider the benefits of incorporating an interactive Python interface into a Monte Carlo application. With PyMercury, a new Python extension to the Mercury general-purpose Monte Carlo particle transport code, we improve application usability without diminishing performance. In two case studies, we illustrate how PyMercury improves usability and simplifies testing and validation in a Monte Carlo application. In short, PyMercury demonstrates the value of interactive Python for Monte Carlo particle transport applications. In the future, we expect interactive Python to play an increasingly significant role in Monte Carlo usage and testing.

  13. PyMercury: Interactive Python for the Mercury Monte Carlo Particle Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    Iandola, F N; O' Brien, M J; Procassini, R J

    2010-11-29

    Monte Carlo particle transport applications are often written in low-level languages (C/C++) for optimal performance on clusters and supercomputers. However, this development approach often sacrifices straightforward usability and testing in the interest of fast application performance. To improve usability, some high-performance computing applications employ mixed-language programming with high-level and low-level languages. In this study, we consider the benefits of incorporating an interactive Python interface into a Monte Carlo application. With PyMercury, a new Python extension to the Mercury general-purpose Monte Carlo particle transport code, we improve application usability without diminishing performance. In two case studies, we illustrate how PyMercury improves usability and simplifies testing and validation in a Monte Carlo application. In short, PyMercury demonstrates the value of interactive Python for Monte Carlo particle transport applications. In the future, we expect interactive Python to play an increasingly significant role in Monte Carlo usage and testing.

  14. STABILITY OF P2 METHODS FOR NEUTRON TRANSPORT EQUATIONS

    Institute of Scientific and Technical Information of China (English)

    袁光伟; 沈智军; 沈隆钧; 周毓麟

    2002-01-01

    In this paper the P2 approximation to the one-group planar neutron transport theory is discussed. The stability of the solutions for P2 equations with general boundary conditions, including the Marshak boundary condition, is proved. Moreover,the stability of the up-wind difference scheme for the P2 equation is demonstrated.

  15. Unbiased estimators of coincidence and correlation in non-analogous Monte Carlo particle transport

    International Nuclear Information System (INIS)

    Highlights: • The history splitting method was developed for non-Boltzmann Monte Carlo estimators. • The method allows variance reduction for pulse-height and higher moment estimators. • It works in highly multiplicative problems but Russian roulette has to be replaced. • Estimation of higher moments allows the simulation of neutron noise measurements. • Biased sampling of fission helps the effective simulation of neutron noise methods. - Abstract: The conventional non-analogous Monte Carlo methods are optimized to preserve the mean value of the distributions. Therefore, they are not suited to non-Boltzmann problems such as the estimation of coincidences or correlations. This paper presents a general method called history splitting for the non-analogous estimation of such quantities. The basic principle of the method is that a non-analogous particle history can be interpreted as a collection of analogous histories with different weights according to the probability of their realization. Calculations with a simple Monte Carlo program for a pulse-height-type estimator prove that the method is feasible and provides unbiased estimation. Different variance reduction techniques have been tried with the method and Russian roulette turned out to be ineffective in high multiplicity systems. An alternative history control method is applied instead. Simulation results of an auto-correlation (Rossi-α) measurement show that even the reconstruction of the higher moments is possible with the history splitting method, which makes the simulation of neutron noise measurements feasible

  16. New electron multiple scattering distributions for Monte Carlo transport simulation

    Energy Technology Data Exchange (ETDEWEB)

    Chibani, Omar (Haut Commissariat a la Recherche (C.R.S.), 2 Boulevard Franz Fanon, Alger B.P. 1017, Alger-Gare (Algeria)); Patau, Jean Paul (Laboratoire de Biophysique et Biomathematiques, Faculte des Sciences Pharmaceutiques, Universite Paul Sabatier, 35 Chemin des Maraichers, 31062 Toulouse cedex (France))

    1994-10-01

    New forms of electron (positron) multiple scattering distributions are proposed. The first is intended for use in the conditions of validity of the Moliere theory. The second distribution takes place when the electron path is so short that only few elastic collisions occur. These distributions are adjustable formulas. The introduction of some parameters allows impositions of the correct value of the first moment. Only positive and analytic functions were used in constructing the present expressions. This makes sampling procedures easier. Systematic tests are presented and some Monte Carlo simulations, as benchmarks, are carried out. ((orig.))

  17. Analysis of neutron and photon response of a TLD-ALBEDO personal dosemeter on an ISO slab phantom using TRIPOLI-4.3 Monte Carlo code.

    Science.gov (United States)

    Lee, Y K

    2005-01-01

    TRIPOLI-4.3 Monte Carlo transport code has been used to evaluate the QUADOS (Quality Assurance of Computational Tools for Dosimetry) problem P4, neutron and photon response of an albedo-type thermoluminescence personal dosemeter (TLD) located on an ISO slab phantom. Two enriched 6LiF and two 7LiF TLD chips were used and they were protected, in front or behind, with a boron-loaded dosemeter-holder. Neutron response of the four chips was determined by counting 6Li(n,t)4He events using ENDF/B-VI.4 library and photon response by estimating absorbed dose (MeV g(-1)). Ten neutron energies from thermal to 20 MeV and six photon energies from 33 keV to 1.25 MeV were used to study the energy dependence. The fraction of the neutron and photon response owing to phantom backscatter has also been investigated. Detailed TRIPOLI-4.3 solutions are presented and compared with MCNP-4C calculations. PMID:16381740

  18. BOT3P: a mesh generation software package for transport analysis with deterministic and Monte Carlo codes

    International Nuclear Information System (INIS)

    BOT3P consists of a set of standard Fortran 77 language programs that gives the users of the deterministic transport codes DORT, TORT, TWODANT, THREEDANT, PARTISN and the sensitivity code SUSD3D some useful diagnostic tools to prepare and check the geometry of their input data files for both Cartesian and cylindrical geometries, including graphical display modules. Users can produce the geometrical and material distribution data for all the cited codes for both two-dimensional and three-dimensional applications and, only in 3-dimensional Cartesian geometry, for the Monte Carlo Transport Code MCNP, starting from the same BOT3P input. Moreover, BOT3P stores the fine mesh arrays and the material zone map in a binary file, the content of which can be easily interfaced to any deterministic and Monte Carlo transport code. This makes it possible to compare directly for the same geometry the effects stemming from the use of different data libraries and solution approaches on transport analysis results. BOT3P Version 5.0 lets users optionally and with the desired precision compute the area/volume error of material zones with respect to the theoretical values, if any, because of the stair-cased representation of the geometry, and automatically update material densities on the whole zone domains to conserve masses. A local (per mesh) density correction approach is also available. BOT3P is designed to run on Linux/UNIX platforms and is publicly available from the Organization for Economic Cooperation and Development (OECD/NEA)/Nuclear Energy Agency Data Bank. Through the use of BOT3P, radiation transport problems with complex 3-dimensional geometrical structures can be modelled easily, as a relatively small amount of engineer-time is required and refinement is achieved by changing few parameters. This tool is useful for solving very large challenging problems, as successfully demonstrated not only in some complex neutron shielding and criticality benchmarks but also in a power

  19. Monte Carlo study of electron transport in monolayer silicene

    Science.gov (United States)

    Borowik, Piotr; Thobel, Jean-Luc; Adamowicz, Leszek

    2016-11-01

    Electron mobility and diffusion coefficients in monolayer silicene are calculated by Monte Carlo simulations using simplified band structure with linear energy bands. Results demonstrate reasonable agreement with the full-band Monte Carlo method in low applied electric field conditions. Negative differential resistivity is observed and an explanation of the origin of this effect is proposed. Electron mobility and diffusion coefficients are studied in low applied electric field conditions. We demonstrate that a comparison of these parameter values can provide a good check that the calculation is correct. Low-field mobility in silicene exhibits {T}-3 temperature dependence for nondegenerate electron gas conditions and {T}-1 for higher electron concentrations, when degenerate conditions are imposed. It is demonstrated that to explain the relation between mobility and temperature in nondegenerate electron gas the linearity of the band structure has to be taken into account. It is also found that electron-electron scattering only slightly modifies low-field electron mobility in degenerate electron gas conditions.

  20. Optimization of a neutron detector design using adjoint transport simulation

    Energy Technology Data Exchange (ETDEWEB)

    Yi, C.; Manalo, K.; Huang, M.; Chin, M.; Edgar, C.; Applegate, S.; Sjoden, G. [Georgia Inst. of Technology, Gilhouse Boggs Bldg., 770 State St, Atlanta, GA 30332-0745 (United States)

    2012-07-01

    A synthetic aperture approach has been developed and investigated for Special Nuclear Materials (SNM) detection in vehicles passing a checkpoint at highway speeds. SNM is postulated to be stored in a moving vehicle and detector assemblies are placed on the road-side or in chambers embedded below the road surface. Neutron and gamma spectral awareness is important for the detector assembly design besides high efficiencies, so that different SNMs can be detected and identified with various possible shielding settings. The detector assembly design is composed of a CsI gamma-ray detector block and five neutron detector blocks, with peak efficiencies targeting different energy ranges determined by adjoint simulations. In this study, formulations are derived using adjoint transport simulations to estimate detector efficiencies. The formulations is applied to investigate several neutron detector designs for Block IV, which has its peak efficiency in the thermal range, and Block V, designed to maximize the total neutron counts over the entire energy spectrum. Other Blocks detect different neutron energies. All five neutron detector blocks and the gamma-ray block are assembled in both MCNP and deterministic simulation models, with detector responses calculated to validate the fully assembled design using a 30-group library. The simulation results show that the 30-group library, collapsed from an 80-group library using an adjoint-weighting approach with the YGROUP code, significantly reduced the computational cost while maintaining accuracy. (authors)

  1. Development of Library Processing System for Neutron Transport Calculation

    Energy Technology Data Exchange (ETDEWEB)

    Song, J. S.; Park, S. Y.; Kim, H. Y. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)] (and others)

    2008-12-15

    A system for library generation was developed for the lattice neutron transport program for pressurized water reactor core analysis. The system extracts multi energy group nuclear data for requested nuclides from ENDF/B whose data are based on continuous energy, generates hydrogen equivalent factor and resonance integral table as functions of temperature and background cross section for resonance nuclides, generates subgroup data for the lattice program to treat resonance exactly as possible, and generates multi-group neutron library file including nuclide depletion data for use of the lattice program.

  2. Coupled neutron and photon cross sections for transport calculations

    International Nuclear Information System (INIS)

    A compact set of multigroup cross sections and transfer tables for use in neutron and photon transport calculations was prepared from ENDF/B-IV using the NJOY processing system. The library includes prompt and steady-state coupled sets for neutrons and photons in FIDO format, prompt and steady-state fission spectra (chi vectors) for the fissionable isotopes, and a table of useful response functions including heating and gas production. These multigroup constants should be useful for a wide variety of problems where self-shielding is not important. 15 references

  3. Monte-Carlo simulation for fragment mass and kinetic energy distributions from neutron induced fission of 235U

    CERN Document Server

    Montoya, M; Rojas, J

    2007-01-01

    The mass and kinetic energy distribution of nuclear fragments from thermal neutron induced fission of 235U have been studied using a Monte-Carlo simulation. Besides reproducing the pronounced broadening on the standard deviation of the final fragment kinetic energy distribution $\\sigma_{e}(m)$ around the mass number m = 109, our simulation also produces a second broadening around m = 125, that is in agreement with the experimental data obtained by Belhafaf et al. These results are consequence of the characteristics of the neutron emission, the variation in the primary fragment mean kinetic energy and the yield as a function of the mass.

  4. Application of the Monte Carlo methods and variational procedure for optimizing time-of-flight neutron diffractometer characteristics

    Science.gov (United States)

    Khrushchinsky, A. A.; Kuten, S. A.; Viarenich, K. A.; Speransky, P. A.

    2016-05-01

    Based on variational calculus, a procedure for the optimal approximation of detector surface of the time-of-flight neutron diffractometer has been suggested. The exact solution for a point sample and zero thickness detector has been obtained. Using the shape of the detector surface, an optimized Monte Carlo simulation has been performed for the parameters of the spectrometer depending on the sample size and detector thickness, its azimuthal and Bragg's angular dimensions, and taking into account the neutron absorption in the sample and detector.

  5. A development of NRESPG Monte Carlo code for the calculation of neutron response function for gas counters

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, N. [Electrotechnical Laboratory, 1-1-4 Umezono, Tsukuba-shi, Ibaraki 305-8568 (Japan); Kudo, K. [Electrotechnical Laboratory, 1-1-4 Umezono, Tsukuba-shi, Ibaraki 305-8568 (Japan); Toyokawa, H. [Electrotechnical Laboratory, 1-1-4 Umezono, Tsukuba-shi, Ibaraki 305-8568 (Japan); Torii, T. [Japan Power Reactor and Nuclear Fuel Development Corporation, Tsuruga Office, Fukui 919-12 (Japan); Hashimoto, M. [Japan Power Reactor and Nuclear Fuel Development Corporation, O-arai Engineering Center, Ibaraki 311-13 (Japan); Sugita, T. [Science System Laboratory, Ibaraki 309-17 (Japan); Dietze, G. [Physikalisch-Technische Bundesanstalt, 38023 Braunschweig (Germany); Yang, X. [China Institute of Atomic Energy (China)

    1999-02-11

    A Monte Carlo code Neutron RESPonse function for Gas counters (NRESPG) has been developed for the calculation of neutron response functions and efficiencies for neutron energies up to 20 MeV, which can be applied for {sup 3}He, H{sub 2}, or BF{sub 3} gas proportional counters with or without moderator. This code can simulate the neutron behavior in a two-dimensional detector configuration and treat the thermal motion of a moderator atom which becomes important as the neutron energy becomes sufficiently low. Further, a more precise measured data was taken to simulate the position-dependent gas multiplication in the sensitive and insensitive gas region of a proportional counter. The NRESPG code has been applied for the calculation of response functions of {sup 3}He cylindrical proportional counters to determine neutron energy and neutron fluence in a monoenergetic calibration field. Thus, a remarkable discrepancy in the lower portion of the full-energy peak produced by the {sup 3}He(n,p)T reaction can be removed which results in a good agreement between simulations and experiments. The code has been also used for the simulation of the response of a McTaggart-type long counter consisting of a central cylindrical BF{sub 3} counter surrounded by a polyethylene moderator. The results of the NRESPG simulations were compared with those obtained from MCNP calculations.

  6. A development of NRESPG Monte Carlo code for the calculation of neutron response function for gas counters

    International Nuclear Information System (INIS)

    A Monte Carlo code Neutron RESPonse function for Gas counters (NRESPG) has been developed for the calculation of neutron response functions and efficiencies for neutron energies up to 20 MeV, which can be applied for 3He, H2, or BF3 gas proportional counters with or without moderator. This code can simulate the neutron behavior in a two-dimensional detector configuration and treat the thermal motion of a moderator atom which becomes important as the neutron energy becomes sufficiently low. Further, a more precise measured data was taken to simulate the position-dependent gas multiplication in the sensitive and insensitive gas region of a proportional counter. The NRESPG code has been applied for the calculation of response functions of 3He cylindrical proportional counters to determine neutron energy and neutron fluence in a monoenergetic calibration field. Thus, a remarkable discrepancy in the lower portion of the full-energy peak produced by the 3He(n,p)T reaction can be removed which results in a good agreement between simulations and experiments. The code has been also used for the simulation of the response of a McTaggart-type long counter consisting of a central cylindrical BF3 counter surrounded by a polyethylene moderator. The results of the NRESPG simulations were compared with those obtained from MCNP calculations

  7. Tripoli-3: monte Carlo transport code for neutral particles - version 3.5 - users manual; Tripoli-3: code de transport des particules neutres par la methode de monte carlo - version 3.5 - manuel d'utilisation

    Energy Technology Data Exchange (ETDEWEB)

    Vergnaud, Th.; Nimal, J.C.; Chiron, M

    2001-07-01

    The TRIPOLI-3 code applies the Monte Carlo method to neutron, gamma-ray and coupled neutron and gamma-ray transport calculations in three-dimensional geometries, either in steady-state conditions or having a time dependence. It can be used to study problems where there is a high flux attenuation between the source zone and the result zone (studies of shielding configurations or source driven sub-critical systems, with fission being taken into account), as well as problems where there is a low flux attenuation (neutronic calculations -- in a fuel lattice cell, for example -- where fission is taken into account, usually with the calculation on the effective multiplication factor, fine structure studies, numerical experiments to investigate methods approximations, etc). TRIPOLI-3 has been operational since 1995 and is the version of the TRIPOLI code that follows on from TRIPOLI-2; it can be used on SUN, RISC600 and HP workstations and on PC using the Linux or Windows/NT operating systems. The code uses nuclear data libraries generated using the THEMIS/NJOY system. The current libraries were derived from ENDF/B6 and JEF2. There is also a response function library based on a number of evaluations, notably the dosimetry libraries IRDF/85, IRDF/90 and also evaluations from JEF2. The treatment of particle transport is the same in version 3.5 as in version 3.4 of the TRIPOLI code; but the version 3.5 is more convenient for preparing the input data and for reading the output. The french version of the user's manual exists. (authors)

  8. Antiproton annihilation physics annihilation physics in the Monte Carlo particle transport code particle transport code SHIELD-HIT12A

    DEFF Research Database (Denmark)

    Taasti, Vicki Trier; Knudsen, Helge; Holzscheiter, Michael;

    2015-01-01

    The Monte Carlo particle transport code SHIELD-HIT12A is designed to simulate therapeutic beams for cancer radiotherapy with fast ions. SHIELD-HIT12A allows creation of antiproton beam kernels for the treatment planning system TRiP98, but first it must be benchmarked against experimental data...

  9. MCANG - a group data library of cumulative angular distributions of elastically scattered neutrons for Monte Carlo calculations

    International Nuclear Information System (INIS)

    A code has been written for producing group data suited to take into account the center of mass anisotropy of elastic neutron scattering in Monte Carlo calculations. The format of the generated data library is described. Up to now variants of the library based on KEDAK2 and KEDAK3/ENDL78 have been produced. One of the libraries is listed in the appendix. (author)

  10. Neutronic performance calculations with alternative fluids in a hybrid reactor by using the Monte Carlo method

    Energy Technology Data Exchange (ETDEWEB)

    Guenay, Mehtap [Malatya Univ. (Turkey). Physics Department

    2015-03-15

    In this study, salt-heavy metal mixtures consisting of 93-85% Li{sub 20}Sn{sub 80} + 5% SFG-PuO{sub 2} and 2-10% UO{sub 2}, 93-85% Li{sub 20}Sn{sub 80} + 5% SFG-PuO{sub 2} and 2-10% NpO{sub 2}, and 93-85% Li{sub 20}Sn{sub 80} + 5% SFG-PuO{sub 2} and 2-10% UCO were used as fluids. The fluids were used in the liquid first wall, blanket, and shield zones of a fusion-fission hybrid reactor system. A beryllium (Be) zone with a width of 3 cm was used for neutron multiplicity between the liquid first wall and the blanket. 9Cr2WVTa ferritic steel with the width of 4 cm was used as the structural material. The contributions of each isotope in the fluids to the nuclear parameters, such as tritium breeding ratio (TBR), energy multiplication factor (M), and heat deposition rate, of the fusion-fission hybrid reactor were calculated in the liquid first wall, blanket, and shield zones. Three-dimensional analyses were performed using the Monte Carlo code MCNPX-2.7.0 and nuclear data library ENDF/B-VII.0.

  11. A Monte Carlo study of the effect of coded-aperture material and thickness on neutron imaging

    International Nuclear Information System (INIS)

    In this paper, a coded-aperture design for a scintillator-based neutron imaging system has been simulated using a series of Monte Carlo simulations. Using Monte Carlo simulations, work to optimise a system making use of the EJ-426 neutron scintillator detector has been conducted. This type of scintillator has a low sensitivity to gamma rays and is therefore particularly useful for neutron detection in a mixed radiation environment. Simulations have been conducted using varying coded-aperture materials and different coded-aperture thicknesses. From this, neutron images have been produced, compared qualitatively and quantitatively for each case to find the best material for the MURA (modified uniformly redundant array) pattern. The neutron images generated also allow observations on how differing thicknesses of coded-aperture impact the system. A system in which a neutron sensitive scintillator has been used in conjunction with a MURA coded aperture to detect and locate a neutron emitting point source centralised in the system has been simulated. A comparison between the results of the different coded-aperture thicknesses is discussed, via the calculation of system error between the reconstructed source location and the actual location. As the system is small scale with a relatively large step along the axis (0.5 cm), it is justifiable to say that the smaller error values provide satisfactory results, which correlate with only a few centimetres difference in the reconstructed source location to actual source location. A general trend of increasing error can be deduced both as the thickness of the coded-aperture material decreases and the capture cross section of the different materials reduces. (authors)

  12. Academic Training - The use of Monte Carlo radiation transport codes in radiation physics and dosimetry

    CERN Multimedia

    Françoise Benz

    2006-01-01

    2005-2006 ACADEMIC TRAINING PROGRAMME LECTURE SERIES 27, 28, 29 June 11:00-12:00 - TH Conference Room, bldg. 4 The use of Monte Carlo radiation transport codes in radiation physics and dosimetry F. Salvat Gavalda,Univ. de Barcelona, A. FERRARI, CERN-AB, M. SILARI, CERN-SC Lecture 1. Transport and interaction of electromagnetic radiation F. Salvat Gavalda,Univ. de Barcelona Interaction models and simulation schemes implemented in modern Monte Carlo codes for the simulation of coupled electron-photon transport will be briefly reviewed. Different schemes for simulating electron transport will be discussed. Condensed algorithms, which rely on multiple-scattering theories, are comparatively fast, but less accurate than mixed algorithms, in which hard interactions (with energy loss or angular deflection larger than certain cut-off values) are simulated individually. The reliability, and limitations, of electron-interaction models and multiple-scattering theories will be analyzed. Benchmark comparisons of simu...

  13. Neutron and photon doses in high energy radiotherapy facilities and evaluation of shielding performance by Monte Carlo method

    International Nuclear Information System (INIS)

    Highlights: → The MCNP5 code has been used to model a radiotherapy room of a 18 MV linear accelerator. → The neutron and the secondary gamma ray dose equivalents were evaluated at various points inside the treatment room and along the the maze. → To reduce the neutron and gamma ray doses, we have also investigated the radiotherapy room shielding performance. → The use of paraffin wax containing boron carbide indicates much better shielding effects. - Abstract: Medical accelerators operating above 10 MV are a source of undesirable neutron radiations which contaminate the therapeutic photon beam. These photoneutrons can also generate secondary gamma rays which increases undesirable dose to the patient body and to personnel and general public. In this study, the Monte Carlo N-Particle MCNP5 code has been used to model the radiotherapy room of a medical linear accelerator operating at 18 MV and to calculate the neutron and the secondary gamma ray energy spectra and the dose equivalents at various points inside the treatment room and along the maze. To validate our Monte Carlo simulation we compared our results with those evaluated by the recommended analytical methods of IAEA Report No. 47, and with experimental and simulated values published in the literature. After validation, the Monte Carlo simulation has been used to evaluate the shielding performance of the radiotherapy room. The obtained results showed that the use of paraffin wax containing boron carbide, in the lining of the radiotherapy room walls, presents enough effectiveness to reduce both neutron and gamma ray doses inside the treatment room and at the maze entrance. Such evaluation cannot be performed by the analytical methods since room material and wall surface lining are not taken into consideration.

  14. Using Nuclear Theory, Data and Uncertainties in Monte Carlo Transport Applications

    Energy Technology Data Exchange (ETDEWEB)

    Rising, Michael Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-11-03

    These are slides for a presentation on using nuclear theory, data and uncertainties in Monte Carlo transport applications. The following topics are covered: nuclear data (experimental data versus theoretical models, data evaluation and uncertainty quantification), fission multiplicity models (fixed source applications, criticality calculations), uncertainties and their impact (integral quantities, sensitivity analysis, uncertainty propagation).

  15. Shape based Monte Carlo code for light transport in complex heterogeneous tissues

    NARCIS (Netherlands)

    Margallo-Balbás, E.; French, P.J.

    2007-01-01

    A Monte Carlo code for the calculation of light transport in heterogeneous scattering media is presented together with its validation. Triangle meshes are used to define the interfaces between different materials, in contrast with techniques based on individual volume elements. This approach allows

  16. Neutron imaging of ion transport in mesoporous carbon materials.

    Science.gov (United States)

    Sharma, Ketki; Bilheux, Hassina Z; Walker, Lakeisha M H; Voisin, Sophie; Mayes, Richard T; Kiggans, Jim O; Yiacoumi, Sotira; DePaoli, David W; Dai, Sheng; Tsouris, Costas

    2013-07-28

    Neutron imaging is presented as a tool for quantifying the diffusion of ions inside porous materials, such as carbon electrodes used in the desalination process via capacitive deionization and in electrochemical energy-storage devices. Monolithic mesoporous carbon electrodes of ∼10 nm pore size were synthesized based on a soft-template method. The electrodes were used with an aqueous solution of gadolinium nitrate in an electrochemical flow-through cell designed for neutron imaging studies. Sequences of neutron images were obtained under various conditions of applied potential between the electrodes. The images revealed information on the direction and magnitude of ion transport within the electrodes. From the time-dependent concentration profiles inside the electrodes, the average value of the effective diffusion coefficient for gadolinium ions was estimated to be 2.09 ± 0.17 × 10(-11) m(2) s(-1) at 0 V and 1.42 ± 0.06 × 10(-10) m(2) s(-1) at 1.2 V. The values of the effective diffusion coefficient obtained from neutron imaging experiments can be used to evaluate model predictions of the ion transport rate in capacitive deionization and electrochemical energy-storage devices. PMID:23756558

  17. Exact-to-precision generalized perturbation for neutron transport calculation

    International Nuclear Information System (INIS)

    This manuscript extends the exact-to-precision generalized perturbation theory (EPGPT), introduced previously, to neutron transport calculation whereby previous developments focused on neutron diffusion calculation only. The EPGPT collectively denotes new developments in generalized perturbation theory (GPT) that place premium on computational efficiency and defendable accuracy in order to render GPT a standard analysis tool in routine design and safety reactor calculations. EPGPT constructs a surrogate model with quantifiable accuracy which can replace the original neutron transport model for subsequent engineering analysis, e.g. functionalization of the homogenized few-group cross sections in terms of various core conditions, sensitivity analysis and uncertainty quantification. This is achieved by reducing the effective dimensionality of the state variable (i.e. neutron angular flux) by projection onto an active subspace. Confining the state variations to the active subspace allows one to construct a small number of what is referred to as the 'active' responses which are solely dependent on the physics model rather than on the responses of interest, the number of input parameters, or the number of points in the state phase space. (authors)

  18. Modelling photon transport in non-uniform media for SPECT with a vectorized Monte Carlo code.

    Science.gov (United States)

    Smith, M F

    1993-10-01

    A vectorized Monte Carlo code has been developed for modelling photon transport in non-uniform media for single-photon-emission computed tomography (SPECT). The code is designed to compute photon detection kernels, which are used to build system matrices for simulating SPECT projection data acquisition and for use in matrix-based image reconstruction. Non-uniform attenuating and scattering regions are constructed from simple three-dimensional geometric shapes, in which the density and mass attenuation coefficients are individually specified. On a Stellar GS1000 computer, Monte Carlo simulations are performed between 1.6 and 2.0 times faster when the vector processor is utilized than when computations are performed in scalar mode. Projection data acquired with a clinical SPECT gamma camera for a line source in a non-uniform thorax phantom are well modelled by Monte Carlo simulations. The vectorized Monte Carlo code was used to stimulate a 99Tcm SPECT myocardial perfusion study, and compensations for non-uniform attenuation and the detection of scattered photons improve activity estimation. The speed increase due to vectorization makes Monte Carlo simulation more attractive as a tool for modelling photon transport in non-uniform media for SPECT. PMID:8248288

  19. Deterministic methods to solve the integral transport equation in neutronic

    International Nuclear Information System (INIS)

    We present a synthesis of the methods used to solve the integral transport equation in neutronic. This formulation is above all used to compute solutions in 2D in heterogeneous assemblies. Three kinds of methods are described: - the collision probability method; - the interface current method; - the current coupling collision probability method. These methods don't seem to be the most effective in 3D. (author). 9 figs

  20. Electron transport through nuclear pasta in magnetized neutron stars

    CERN Document Server

    Yakovlev, D G

    2015-01-01

    We present a simple model for electron transport in a possible layer of exotic nuclear clusters (in the so called nuclear pasta layer) between the crust and liquid core of a strongly magnetized neutron star. The electron transport there can be strongly anisotropic and gyrotropic. The anisotropy is produced by different electron effective collision frequencies along and across local symmetry axis in domains of exotic ordered nuclear clusters and by complicated effects of the magnetic field. We also calculate averaged kinetic coefficients in case local domains are freely oriented. Possible applications of the obtained results and open problems are outlined.

  1. Improvements in Neutronics/Thermal-Hydraulics Coupling in Two-Phase Flow Systems Using Stochastic-Mixture Transport Models

    CERN Document Server

    Palmer, T S

    2003-01-01

    In this NEER project, researchers from Oregon State University have investigated the limitations of the treatment of two-phase coolants as a homogeneous mixture in neutron transport calculations. Improved methods of calculating the neutron distribution in binary stochastic mixtures have been developed over the past 10-15 years and are readily available in the transport literature. These methods are computationally more expensive than the homogeneous (or atomic mix) models, but can give much more accurate estimates of ensemble average fluxes and reaction rates provided statistical descriptions of the distributions of the two materials are know. A thorough review of the two-phase flow literature has been completed and the relevant mixture distributions have been identified. Using these distributions, we have performed Monte Carlo criticality calculations of fuel assemblies to assess the accuracy of the atomic mix approximation when compared to a resolved treatment of the two-phase coolant. To understand the ben...

  2. Development and benchmarking of higher energy neutron transport data libraries

    International Nuclear Information System (INIS)

    Neutron cross-section evaluations covering the energy range from 10/sup /minus/11/ to 100 MeV have been prepared for several materials. The principal method used to generate this data base has employed statistical-preequilibrium nuclear models, sophisticated phase shift analyses, and R-matrix techniques. The library takes advantage of formats developed for Version 6 of the Evaluated Nuclear Data File, ENDF. Methods to efficiently utilize the ENDF/B-VI representation of this library in the MCNP Monte Carlo code have been developed. MCNP results using the new library have been compared with calculated results using codes or data based upon intranuclear cascade models. 7 refs., 8 figs

  3. Numerical research on the anisotropic transport of thermal neutron in heterogeneous porous media with micron X-ray computed tomography

    Science.gov (United States)

    Wang, Yong; Yue, Wenzheng; Zhang, Mo

    2016-06-01

    The anisotropic transport of thermal neutron in heterogeneous porous media is of great research interests in many fields. In this paper, it is the first time that a new model based on micron X-ray computed tomography (CT) has been proposed to simultaneously consider both the separation of matrix and pore and the distribution of mineral components. We apply the Monte Carlo method to simulate thermal neutrons transporting through the model along different directions, and meanwhile detect those unreacted thermal neutrons by an array detector on the other side of the model. Therefore, the anisotropy of pore structure can be imaged by the amount of received thermal neutrons, due to the difference of rock matrix and pore-filling fluids in the macroscopic reaction cross section (MRCS). The new model has been verified by the consistent between the simulated data and the pore distribution from X-ray CT. The results show that the evaluation of porosity can be affected by the anisotropy of media. Based on the research, a new formula is developed to describe the correlation between the resolution of array detectors and the quality of imaging. The formula can be further used to analyze the critical resolution and the suitable number of thermal neutrons emitted in each simulation. Unconventionally, we find that a higher resolution cannot always lead to a better image.

  4. User manual for version 4.3 of the Tripoli-4 Monte-Carlo method particle transport computer code

    International Nuclear Information System (INIS)

    This manual relates to Version 4.3 TRIPOLI-4 code. TRIPOLI-4 is a computer code simulating the transport of neutrons, photons, electrons and positrons. It can be used for radiation shielding calculations (long-distance propagation with flux attenuation in non-multiplying media) and neutronic calculations (fissile medium, criticality or sub-criticality basis). This makes it possible to calculate keff (for criticality), flux, currents, reaction rates and multi-group cross-sections. TRIPOLI-4 is a three-dimensional code that uses the Monte-Carlo method. It allows for point-wise description in terms of energy of cross-sections and multi-group homogenized cross-sections and features two modes of geometrical representation: surface and combinatorial. The code uses cross-section libraries in ENDF/B format (such as JEF2-2, ENDF/B-VI and JENDL) for point-wise description cross-sections in APOTRIM format (from the APOLLO2 code) or a format specific to TRIPOLI-4 for multi-group description. (authors)

  5. Comparison and physical interpretation of MCNP and TART neutron and γ Monte Carlo shielding calculations for a heavy-ion ICF system

    International Nuclear Information System (INIS)

    Inertial confinement fusion (ICF) aims to induce implosions of D-T pellets to obtain a extremely dense and hot plasma with lasers or heavy-ion beams. For heavy-ion fusion (HIF), recent research has focused on 'liquid-protected' designs that allow highly compact target chambers. In the design of a reactor such as HYLIFE-II [Fus. Techol. 25 (1984); HYLIFE-II Progress Report, UCID-21816, 4.82-100], the liquid used is a molten salt made of F10, Li6, Li7, Be9 (called flibe). Flibe allows the final-focus magnets to be closer to the target, which helps to reduce the focus spot size and in turn the size of the driver, with a large reduction of the cost of HIF electricity. Consequently the superconducting coils of the magnets closer to the D-T neutron source will potentially suffer higher damage though they can stand only a certain amount of energy deposited before quenching. This work has been primarily focusing on verifying that total energy deposited by fusion neutrons and induced γ rays remain under such limit values and the final purpose is the optimization of the shielding of the magnetic lens system from the points of view of the geometrical configuration and of the physical nature of the materials adopted. The system is analyzed in terms of six geometrical models going from simplified up to much more realistic representations of a system of 192 beam lines, each focused by six magnets. A 3-D transport calculation of the radiation penetrating through ducts, that takes into account the complexity of the system, requires Monte Carlo methods. The technical nature of the design problem and the methodology followed were presented in a previous paper [Nucl. Instr. and Meth. A 464 (2001) 410] by summarizing briefly the results for the deposited energy distribution on the six focal magnets of a beam line. Now a comparison of the performances of the two codes TART98 [TART98: A Coupled Neutron-Photon 3-D Combinational Geometry Monte Carlo Transport Code, Lawrence Livermore

  6. Monte Carlo modeling and analyses of YALINA-booster subcritical assembly part 1: analytical models and main neutronics parameters.

    Energy Technology Data Exchange (ETDEWEB)

    Talamo, A.; Gohar, M. Y. A.; Nuclear Engineering Division

    2008-09-11

    This study was carried out to model and analyze the YALINA-Booster facility, of the Joint Institute for Power and Nuclear Research of Belarus, with the long term objective of advancing the utilization of accelerator driven systems for the incineration of nuclear waste. The YALINA-Booster facility is a subcritical assembly, driven by an external neutron source, which has been constructed to study the neutron physics and to develop and refine methodologies to control the operation of accelerator driven systems. The external neutron source consists of Californium-252 spontaneous fission neutrons, 2.45 MeV neutrons from Deuterium-Deuterium reactions, or 14.1 MeV neutrons from Deuterium-Tritium reactions. In the latter two cases a deuteron beam is used to generate the neutrons. This study is a part of the collaborative activity between Argonne National Laboratory (ANL) of USA and the Joint Institute for Power and Nuclear Research of Belarus. In addition, the International Atomic Energy Agency (IAEA) has a coordinated research project benchmarking and comparing the results of different numerical codes with the experimental data available from the YALINA-Booster facility and ANL has a leading role coordinating the IAEA activity. The YALINA-Booster facility has been modeled according to the benchmark specifications defined for the IAEA activity without any geometrical homogenization using the Monte Carlo codes MONK and MCNP/MCNPX/MCB. The MONK model perfectly matches the MCNP one. The computational analyses have been extended through the MCB code, which is an extension of the MCNP code with burnup capability because of its additional feature for analyzing source driven multiplying assemblies. The main neutronics parameters of the YALINA-Booster facility were calculated using these computer codes with different nuclear data libraries based on ENDF/B-VI-0, -6, JEF-2.2, and JEF-3.1.

  7. Lorentz force correction to the Boltzmann radiation transport equation and its implications for Monte Carlo algorithms

    International Nuclear Information System (INIS)

    To establish a theoretical framework for generalizing Monte Carlo transport algorithms by adding external electromagnetic fields to the Boltzmann radiation transport equation in a rigorous and consistent fashion. Using first principles, the Boltzmann radiation transport equation is modified by adding a term describing the variation of the particle distribution due to the Lorentz force. The implications of this new equation are evaluated by investigating the validity of Fano’s theorem. Additionally, Lewis’ approach to multiple scattering theory in infinite homogeneous media is redefined to account for the presence of external electromagnetic fields. The equation is modified and yields a description consistent with the deterministic laws of motion as well as probabilistic methods of solution. The time-independent Boltzmann radiation transport equation is generalized to account for the electromagnetic forces in an additional operator similar to the interaction term. Fano’s and Lewis’ approaches are stated in this new equation. Fano’s theorem is found not to apply in the presence of electromagnetic fields. Lewis’ theory for electron multiple scattering and moments, accounting for the coupling between the Lorentz force and multiple elastic scattering, is found. However, further investigation is required to develop useful algorithms for Monte Carlo and deterministic transport methods. To test the accuracy of Monte Carlo transport algorithms in the presence of electromagnetic fields, the Fano cavity test, as currently defined, cannot be applied. Therefore, new tests must be designed for this specific application. A multiple scattering theory that accurately couples the Lorentz force with elastic scattering could improve Monte Carlo efficiency. The present study proposes a new theoretical framework to develop such algorithms. (paper)

  8. SHIELD-HIT12A - a Monte Carlo particle transport program for ion therapy research

    DEFF Research Database (Denmark)

    Bassler, Niels; Hansen, David Christoffer; Lühr, Armin;

    2014-01-01

    Abstract. Purpose: The Monte Carlo (MC) code SHIELD-HIT simulates the transport of ions through matter. Since SHIELD-HIT08 we added numerous features that improves speed, usability and underlying physics and thereby the user experience. The “-A” fork of SHIELD-HIT also aims to attach SHIELD...... of computation time. Scheduled for later release are CT import and photon-electron transport. Conclusions: SHIELD-HIT12A is an interesting alternative ion transport engine. Apart from being a flexible particle therapy research tool, it can also serve as a back end for a MC ion treatment planning system. More...

  9. High-resolution Monte Carlo simulation of flow and conservative transport in heterogeneous porous media 2. Transport results

    Science.gov (United States)

    Naff, R.L.; Haley, D.F.; Sudicky, E.A.

    1998-01-01

    In this, the second of two papers concerned with the use of numerical simulation to examine flow and transport parameters in heterogeneous porous media via Monte Carlo methods, results from the transport aspect of these simulations are reported on. Transport simulations contained herein assume a finite pulse input of conservative tracer, and the numerical technique endeavors to realistically simulate tracer spreading as the cloud moves through a heterogeneous medium. Medium heterogeneity is limited to the hydraulic conductivity field, and generation of this field assumes that the hydraulic- conductivity process is second-order stationary. Methods of estimating cloud moments, and the interpretation of these moments, are discussed. Techniques for estimation of large-time macrodispersivities from cloud second-moment data, and for the approximation of the standard errors associated with these macrodispersivities, are also presented. These moment and macrodispersivity estimation techniques were applied to tracer clouds resulting from transport scenarios generated by specific Monte Carlo simulations. Where feasible, moments and macrodispersivities resulting from the Monte Carlo simulations are compared with first- and second-order perturbation analyses. Some limited results concerning the possible ergodic nature of these simulations, and the presence of non- Gaussian behavior of the mean cloud, are reported on as well.

  10. Data decomposition of Monte Carlo particle transport simulations via tally servers

    Energy Technology Data Exchange (ETDEWEB)

    Romano, Paul K., E-mail: paul.k.romano@gmail.com [Massachusetts Institute of Technology, Department of Nuclear Science and Engineering, 77 Massachusetts Ave., Cambridge, MA 02139 (United States); Siegel, Andrew R., E-mail: siegala@mcs.anl.gov [Argonne National Laboratory, Theory and Computing Sciences, 9700 S Cass Ave., Argonne, IL 60439 (United States); Forget, Benoit, E-mail: bforget@mit.edu [Massachusetts Institute of Technology, Department of Nuclear Science and Engineering, 77 Massachusetts Ave., Cambridge, MA 02139 (United States); Smith, Kord, E-mail: kord@mit.edu [Massachusetts Institute of Technology, Department of Nuclear Science and Engineering, 77 Massachusetts Ave., Cambridge, MA 02139 (United States)

    2013-11-01

    An algorithm for decomposing large tally data in Monte Carlo particle transport simulations is developed, analyzed, and implemented in a continuous-energy Monte Carlo code, OpenMC. The algorithm is based on a non-overlapping decomposition of compute nodes into tracking processors and tally servers. The former are used to simulate the movement of particles through the domain while the latter continuously receive and update tally data. A performance model for this approach is developed, suggesting that, for a range of parameters relevant to LWR analysis, the tally server algorithm should perform with minimal overhead on contemporary supercomputers. An implementation of the algorithm in OpenMC is then tested on the Intrepid and Titan supercomputers, supporting the key predictions of the model over a wide range of parameters. We thus conclude that the tally server algorithm is a successful approach to circumventing classical on-node memory constraints en route to unprecedentedly detailed Monte Carlo reactor simulations.

  11. Electron transport in radiotherapy using local-to-global Monte Carlo

    International Nuclear Information System (INIS)

    Local-to-Global (L-G) Monte Carlo methods are a way to make three-dimensional electron transport both fast and accurate relative to other Monte Carlo methods. This is achieved by breaking the simulation into two stages: a local calculation done over small geometries having the size and shape of the ''steps'' to be taken through the mesh; and a global calculation which relies on a stepping code that samples the stored results of the local calculation. The increase in speed results from taking fewer steps in the global calculation than required by ordinary Monte Carlo codes and by speeding up the calculation per step. The potential for accuracy comes from the ability to use long runs of detailed codes to compile probability distribution functions (PDFs) in the local calculation. Specific examples of successful Local-to-Global algorithms are given

  12. Application of Photon Transport Monte Carlo Module with GPU-based Parallel System

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chang Je [Sejong University, Seoul (Korea, Republic of); Shon, Heejeong [Golden Eng. Co. LTD, Seoul (Korea, Republic of); Lee, Donghak [CoCo Link Inc., Seoul (Korea, Republic of)

    2015-05-15

    In general, it takes lots of computing time to get reliable results in Monte Carlo simulations especially in deep penetration problems with a thick shielding medium. To mitigate such a weakness of Monte Carlo methods, lots of variance reduction algorithms are proposed including geometry splitting and Russian roulette, weight windows, exponential transform, and forced collision, etc. Simultaneously, advanced computing hardware systems such as GPU(Graphics Processing Units)-based parallel machines are used to get a better performance of the Monte Carlo simulation. The GPU is much easier to access and to manage when comparing a CPU cluster system. It also becomes less expensive these days due to enhanced computer technology. There, lots of engineering areas adapt GPU-bases massive parallel computation technique. based photon transport Monte Carlo method. It provides almost 30 times speedup without any optimization and it is expected almost 200 times with fully supported GPU system. It is expected that GPU system with advanced parallelization algorithm will contribute successfully for development of the Monte Carlo module which requires quick and accurate simulations.

  13. Application of Photon Transport Monte Carlo Module with GPU-based Parallel System

    International Nuclear Information System (INIS)

    In general, it takes lots of computing time to get reliable results in Monte Carlo simulations especially in deep penetration problems with a thick shielding medium. To mitigate such a weakness of Monte Carlo methods, lots of variance reduction algorithms are proposed including geometry splitting and Russian roulette, weight windows, exponential transform, and forced collision, etc. Simultaneously, advanced computing hardware systems such as GPU(Graphics Processing Units)-based parallel machines are used to get a better performance of the Monte Carlo simulation. The GPU is much easier to access and to manage when comparing a CPU cluster system. It also becomes less expensive these days due to enhanced computer technology. There, lots of engineering areas adapt GPU-bases massive parallel computation technique. based photon transport Monte Carlo method. It provides almost 30 times speedup without any optimization and it is expected almost 200 times with fully supported GPU system. It is expected that GPU system with advanced parallelization algorithm will contribute successfully for development of the Monte Carlo module which requires quick and accurate simulations

  14. A ''local'' exponential transform method for global variance reduction in Monte Carlo transport problems

    International Nuclear Information System (INIS)

    Numerous variance reduction techniques, such as splitting/Russian roulette, weight windows, and the exponential transform exist for improving the efficiency of Monte Carlo transport calculations. Typically, however, these methods, while reducing the variance in the problem area of interest tend to increase the variance in other, presumably less important, regions. As such, these methods tend to be not as effective in Monte Carlo calculations which require the minimization of the variance everywhere. Recently, ''Local'' Exponential Transform (LET) methods have been developed as a means of approximating the zero-variance solution. A numerical solution to the adjoint diffusion equation is used, along with an exponential representation of the adjoint flux in each cell, to determine ''local'' biasing parameters. These parameters are then used to bias the forward Monte Carlo transport calculation in a manner similar to the conventional exponential transform, but such that the transform parameters are now local in space and energy, not global. Results have shown that the Local Exponential Transform often offers a significant improvement over conventional geometry splitting/Russian roulette with weight windows. Since the biasing parameters for the Local Exponential Transform were determined from a low-order solution to the adjoint transport problem, the LET has been applied in problems where it was desirable to minimize the variance in a detector region. The purpose of this paper is to show that by basing the LET method upon a low-order solution to the forward transport problem, one can instead obtain biasing parameters which will minimize the maximum variance in a Monte Carlo transport calculation

  15. The specific purpose Monte Carlo code McENL for simulating the response of epithermal neutron lifetime well logging tools

    International Nuclear Information System (INIS)

    A new specific purpose Monte Carlo code called McENL for modeling the time response of epithermal neutron lifetime tools is described. The code was developed so that the Monte Carlo neophyte can easily use it. A minimum amount of input preparation is required and specified fixed values of the parameters used to control the code operation can be used. The weight windows technique, employing splitting and Russian Roulette, is used with an automated importance function based on the solution of an adjoint diffusion model to improve the code efficiency. Complete composition and density correlated sampling is also included in the code and can be used to study the effect on tool response of small variations in the formation, borehole, or logging tool composition and density. An illustration of the latter application is given here for the density of a thermal neutron filter. McENL was benchmarked against test-pit data for the Mobil pulsed neutron porosity (PNP) tool and found to be very accurate. Results of the experimental validation and details of code performance are presented

  16. Beam-transport optimization for cold-neutron spectrometer

    Directory of Open Access Journals (Sweden)

    Nakajima Kenji

    2015-01-01

    Full Text Available We report the design of the beam-transport system (especially the vertical geometry for a cold-neutron disk-chopper spectrometer AMATERAS at J-PARC. Based on the elliptical shape, which is one of the most effective geometries for a ballistic mirror, the design was optimized to obtain, at the sample position, a neutron beam with high flux without serious degrading in divergence and spacial homogeneity within the boundary conditions required from actual spectrometer construction. The optimum focal point was examined. An ideal elliptical shape was modified to reduce its height without serious loss of transmission. The final result was adapted to the construction requirements of AMATERAS. Although the ideas studied in this paper are considered for the AMATERAS case, they can be useful also to other spectrometers in similar situations.

  17. Discretized mesh tools and related treatment for hybrid transport application with 3d discrete ordinates and Monte Carlo

    International Nuclear Information System (INIS)

    Hybrid methods of neutron transport have increased greatly in use, for example, in applications of using both Monte Carlo and deterministic transport methods to calculate quantities of interest, such as the flux and eigenvalue in a nuclear reactor. Many 3d parallel Sn codes apply a Cartesian mesh, and thus for nuclear reactors the representation of curved fuels (cylinder, sphere, etc.) are impacted in the representation of proper fuel inventory, resulting in both a deviation of mass and exact geometry in the computer model representation. In addition, we discuss auto-conversion techniques with our 3d Cartesian mesh generation tools to allow for full generation of MCNP5 inputs (Cartesian mesh and Multigroup XS) from a basis PENTRAN Sn model. For a PWR assembly eigenvalue problem, we explore the errors associated with this Cartesian discrete mesh representation, and perform an analysis to calculate a slope parameter that relates the pcm to the percent areal/volumetric deviation (areal → 2d problems, volumetric → 3d problems). This paper analysis demonstrates a linear relationship between pcm change and areal/volumetric deviation using Multigroup MCNP on a PWR assembly compared to a reference exact combinatorial MCNP geometry calculation. For the same MCNP multigroup problems, we also characterize this linear relationship in discrete ordinates (3d PENTRAN). Finally, for 3D Sn models, we show an application of corner fractioning, a volume-weighted recovery of underrepresented target fuel mass that reduced pcm error to < 100, compared to reference Monte Carlo, in the application to a PWR assembly. (author)

  18. Validation and benchmarking of calculation methods for photon and neutron transport at cask configurations

    International Nuclear Information System (INIS)

    The reliability of calculation tools to evaluate and calculate dose rates appearing behind multi-layered shields is important with regard to the certification of transport and storage casks. Actual benchmark databases like SINBAD do not offer such configurations because they were developed for reactor and accelerator purposes. Due to this, a bench-mark-suite based on own experiments that contain dose rates measured in different distances and levels from a transport and storage cask and on a public benchmark to validate Monte-Carlo-transport-codes has been developed. The analysed and summarised experiments include a 60Co point-source located in a cylindrical cask, a 252Cf line-source shielded by iron and polyethylene (PE) and a bare 252Cf source moderated by PE in a concrete-labyrinth with different inserted shielding materials to quantify neutron streaming effects on measured dose rates. In detail not only MCNPTM (version 5.1.6) but also MAVRIC, included in the SCALE 6.1 package, have been compared for photon and neutron transport. Aiming at low deviations between calculation and measurement requires precise source term specification and exact measurements of the dose rates which have been evaluated carefully including known uncertainties. In MAVRIC different source-descriptions with respect to the group-structure of the nuclear data library are analysed for the calculation of gamma dose rates because the energy lines of 60Co can only be modelled in groups. In total the comparison shows that MCNPTM fits very wall to the measurements within up to two standard deviations and that MAVRIC behaves similarly under the prerequisite that the source-model can be optimized. (author)

  19. Geant4 Simulation of Neutron Penumbral Imaging

    Institute of Scientific and Technical Information of China (English)

    ZHENG; Yu-lai; WANG; Qiang; YANG; Lu; LI; Yong

    2012-01-01

    <正>The penumbral imaging technology is effective analysis method of Inertial Confinement Fusion (ICF) neutron imaging. To meet neutron penumbral imaging need, simulation of neutron transport in penumbral imaging systems was done by using Monte Carlo program Geant4, and two-dimensional image was got.

  20. Minimizing the cost of splitting in Monte Carlo radiation transport simulation

    Energy Technology Data Exchange (ETDEWEB)

    Juzaitis, R.J.

    1980-10-01

    A deterministic analysis of the computational cost associated with geometric splitting/Russian roulette in Monte Carlo radiation transport calculations is presented. Appropriate integro-differential equations are developed for the first and second moments of the Monte Carlo tally as well as time per particle history, given that splitting with Russian roulette takes place at one (or several) internal surfaces of the geometry. The equations are solved using a standard S/sub n/ (discrete ordinates) solution technique, allowing for the prediction of computer cost (formulated as the product of sample variance and time per particle history, sigma/sup 2//sub s/tau p) associated with a given set of splitting parameters. Optimum splitting surface locations and splitting ratios are determined. Benefits of such an analysis are particularly noteworthy for transport problems in which splitting is apt to be extensively employed (e.g., deep penetration calculations).

  1. The use of Monte Carlo radiation transport codes in radiation physics and dosimetry

    CERN Document Server

    CERN. Geneva; Ferrari, Alfredo; Silari, Marco

    2006-01-01

    Transport and interaction of electromagnetic radiation Interaction models and simulation schemes implemented in modern Monte Carlo codes for the simulation of coupled electron-photon transport will be briefly reviewed. In these codes, photon transport is simulated by using the detailed scheme, i.e., interaction by interaction. Detailed simulation is easy to implement, and the reliability of the results is only limited by the accuracy of the adopted cross sections. Simulations of electron and positron transport are more difficult, because these particles undergo a large number of interactions in the course of their slowing down. Different schemes for simulating electron transport will be discussed. Condensed algorithms, which rely on multiple-scattering theories, are comparatively fast, but less accurate than mixed algorithms, in which hard interactions (with energy loss or angular deflection larger than certain cut-off values) are simulated individually. The reliability, and limitations, of electron-interacti...

  2. Monte-Carlo simulation of cement neutron field distribution characteristics in PGNAA

    International Nuclear Information System (INIS)

    The distribution characteristics of the neutron field in cement was simulated using the MCNP code to comply with the requirements of an online Prompt Gamma Neutron Activation Analysis system. Simulation results showed that the neutron relative flux proportion reduced with increasing cement thickness. When the cement thickness remains unchanged, the reduced proportion of thermal neutrons increases to a small extent, but the epithermal, intermediate, and fast neutrons will decrease according to the geometric progression. H element in the cement mainly affects the reduction of fast neutrons and other single-substance elements, e.g., O, Ca, 56Fe, Si, and Al. It also slows down the reduction of the fast neutrons via inelastic scattering. O contributes more than other elements in the reduction of fast neutrons. Changing the H content affects the thermal, epithermal, intermediate, and fast neutrons, while changing the Ca, Fe, and Si contents only influences the thermal, epithermal, and intermediate neutrons; hence, there is little effect on the reduction of fast neutrons. (authors)

  3. A comparison between the Monte Carlo radiation transport codes MCNP and MCBEND

    Energy Technology Data Exchange (ETDEWEB)

    Sawamura, Hidenori; Nishimura, Kazuya [Computer Software Development Co., Ltd., Tokyo (Japan)

    2001-01-01

    In Japan, almost of all radiation analysts are using the MCNP code and MVP code on there studies. But these codes have not had automatic variance reduction. MCBEND code made by UKAEA have automatic variance reduction. And, MCBEND code is user friendly more than other Monte Carlo Radiation Transport Codes. Our company was first introduced MCBEND code in Japan. Therefore, we compared with MCBEND code and MCNP code about functions and production capacity. (author)

  4. A Monte Carlo Simulation for the Ion Transport in Glow Discharges with Dusts

    Institute of Scientific and Technical Information of China (English)

    SUN Ai-Ping; PU Wei; QIU Xiao-Ming

    2001-01-01

    We use the Monte Carlo method to simulate theion transport in the rf parallel plate glow discharge with a negative-voltage pulse connected to the electrode. It is found that self-consistent field, dust charge, dust concentration,and dust size influence the energy distribution and the density of the ions arriving at the target, and in particular, the latter two make significant influence. As dust concentration or dust size increases, the number of ions arriving at the target reduces greatly.

  5. Salt-dependent DNA superhelix diameter studied by small angle neutron scattering measurements and Monte Carlo simulations.

    OpenAIRE

    Hammermann, M; Brun, N; Klenin, K V; May, R.; Tóth, K; Langowski, J.

    1998-01-01

    Using small angle neutron scattering we have measured the static form factor of two different superhelical DNAs, p1868 (1868 bp) and pUC18 (2686 bp), in dilute aqueous solution at salt concentrations between 0 and 1.5 M Na+ in 10 mM Tris at 0% and 100% D2O. For both DNA molecules, the theoretical static form factor was also calculated from an ensemble of Monte Carlo configurations generated by a previously described model. Simulated and measured form factors of both DNAs showed the same behav...

  6. Monte Carlo simulation of an in-situ search of water on the Martian surface by using neutron spectroscopy

    CERN Document Server

    Vincke, H H; Müller, H; Bruckner, J

    2003-01-01

    In this paper the concept for in-situ search of water in the Martian soil by applying neutron spectroscopy is examined. Monte-Carlo simulations were carried out to determine homogeneous water concentrations in the Martian surface. In addition, the effect of an ice layer with a thickness of 10 cm, buried in the soil, was investigated. Furthermore, a method is presented that provides the ability to distinguish between the effects caused by a homogeneous water distribution and an ice layer located at different depths.

  7. Combining measurements and 3D neutron transport calculations. A powerful tool in detailed neutron dosimetry and damage analysis

    International Nuclear Information System (INIS)

    It is shown that the combination of 3D neutron transport calculations and the results from activation foil measurements at a limited number of locations in a materials testing irradiation experiment can provide information at any position in the experiment for detailed neutron dosimetry and damage analysis. 4 refs

  8. Monte Carlo simulation of the property of a scintillation bar in the multi-neutron correlation spectrometer

    Institute of Scientific and Technical Information of China (English)

    SONG Yu-Shou; YE Yan-Lin; GE Yu-Cheng; L(U) Lin-Hui; Faisal Q.; JIANG Dong-Xing; HUA Hui; ZHENG Wao; LI Zhi-Huan; LI Xiang-Qing; LOU Jian-Ling; LU Fei; FAN Feng-Ying; CAO Zhong-Xin; LI Qi-Te; XIAO Jun

    2009-01-01

    To perform a kinematically complete measurement of the dissociation reaction for neutron-rich nuclei, a multi-neutron correlation spectrometer is proposed at Peking University.A Monte Carlo simulation code based on GEANT4 is developed for a single scintillation bar which processes not only the energy deposition but also the light propagation in the scintillator and the light collection and conversion to signal at the end of the bar in a realistic way. The simulating method is described in detail in this paper, and the timing and position resolutions and detector efficiency are studied based on the simulation and compared with the experimental results.A new method of crosstalk rejection has been demonstrated to be important for the design of the whole spectrometer.

  9. Variance analysis of the Monte-Carlo perturbation source method in inhomogeneous linear particle transport problems

    International Nuclear Information System (INIS)

    The perturbation source method may be a powerful Monte-Carlo means to calculate small effects in a particle field. In a preceding paper we have formulated this methos in inhomogeneous linear particle transport problems describing the particle fields by solutions of Fredholm integral equations and have derived formulae for the second moment of the difference event point estimator. In the present paper we analyse the general structure of its variance, point out the variance peculiarities, discuss the dependence on certain transport games and on generation procedures of the auxiliary particles and draw conclusions to improve this method

  10. Time-implicit Monte-Carlo collision algorithm for particle-in-cell electron transport models

    International Nuclear Information System (INIS)

    A time-implicit Monte-Carlo collision algorithm has been developed to allow particle-in-cell electron transport models to be applied to arbitrarily collisional systems. The algorithm is formulated for electrons moving in response to electric and magnetic accelerations and subject to collisional drag and scattering due to a background plasma. The correct fluid or streaming transport results are obtained in the respective limits of strongly- or weakly-collisional systems, and reasonable behavior is produced even for time steps greatly exceeding the magnetic-gyration and collisional-scattering times

  11. Sensitivity of the scalar and the angular neutron flux to the anisotropic scattering in Monte Carlo calculations

    International Nuclear Information System (INIS)

    The anisotropic scattering influences both the transport and slowing processes of neutrons. Since Practical shields are usually anisotropic scatters, several parameterized, anisotropic scattering kernels were used to present a general class of anisotropies. To study the anisotropic sensitivity of the flux in thick shield medium, the feasibility of track- length distribution biasing for calculations of scalar and angular neutron flux and their sensitivity to anisotropic scattering was investigated. To represent more realistic angular distribution in a parameterized functional form, an exponential angular density for sampling the scattering angle is proposed, also an empirical formula for the choice of optimal parameter for track length biasing depending on the anisotropic scattering is proposed. The calculations are performed for a particle transport model having an exact solution. The results show that this distribution covers also isotropic and the anisotropic scattering case. The anisotropic effect has a great influence on the behavior of neutron distribution particularly in thick shield. (author)

  12. Monte Carlo assessment of soil moisture effect on high-energy thermal neutron capture gamma-ray by 14N.

    Science.gov (United States)

    Pazirandeh, Ali; Azizi, Maryam; Farhad Masoudi, S

    2006-01-01

    Among many conventional techniques, nuclear techniques have shown to be faster, more reliable, and more effective in detecting explosives. In the present work, neutrons from a 5 Ci Am-Be neutron source being in water tank are captured by elements of soil and landmine (TNT), namely (14)N, H, C, and O. The prompt capture gamma-ray spectrum taken by a NaI (Tl) scintillation detector indicates the characteristic photo peaks of the elements in soil and landmine. In the high-energy region of the gamma-ray spectrum, besides 10.829 MeV of (15)N, single escape (SE) and double escape (DE) peaks are unmistakable photo peaks, which make the detection of concealed explosive possible. The soil has the property of moderating neutrons as well as diffusing the thermal neutron flux. Among many elements in soil, silicon is more abundant and (29)Si emits 10.607 MeV prompt capture gamma-ray, which makes 10.829 MeV detection difficult. The Monte Carlo simulation was used to adjust source-target-detector distances and soil moisture content to yield the best result. Therefore, we applied MCNP4C for configuration very close to reality of a hidden landmine in soil.

  13. Thermal neutron response of a boron-coated GEM detector via GEANT4 Monte Carlo code.

    Science.gov (United States)

    Jamil, M; Rhee, J T; Kim, H G; Ahmad, Farzana; Jeon, Y J

    2014-10-22

    In this work, we report the design configuration and the performance of the hybrid Gas Electron Multiplier (GEM) detector. In order to make the detector sensitive to thermal neutrons, the forward electrode of the GEM has been coated with the enriched boron-10 material, which works as a neutron converter. A total of 5×5cm(2) configuration of GEM has been used for thermal neutron studies. The response of the detector has been estimated via using GEANT4 MC code with two different physics lists. Using the QGSP_BIC_HP physics list, the neutron detection efficiency was determined to be about 3%, while with QGSP_BERT_HP physics list the efficiency was around 2.5%, at the incident thermal neutron energies of 25meV. The higher response of the detector proves that GEM-coated with boron converter improves the efficiency for thermal neutrons detection.

  14. Thermal neutron response of a boron-coated GEM detector via GEANT4 Monte Carlo code.

    Science.gov (United States)

    Jamil, M; Rhee, J T; Kim, H G; Ahmad, Farzana; Jeon, Y J

    2014-10-22

    In this work, we report the design configuration and the performance of the hybrid Gas Electron Multiplier (GEM) detector. In order to make the detector sensitive to thermal neutrons, the forward electrode of the GEM has been coated with the enriched boron-10 material, which works as a neutron converter. A total of 5×5cm(2) configuration of GEM has been used for thermal neutron studies. The response of the detector has been estimated via using GEANT4 MC code with two different physics lists. Using the QGSP_BIC_HP physics list, the neutron detection efficiency was determined to be about 3%, while with QGSP_BERT_HP physics list the efficiency was around 2.5%, at the incident thermal neutron energies of 25meV. The higher response of the detector proves that GEM-coated with boron converter improves the efficiency for thermal neutrons detection. PMID:25464183

  15. Transport methods: general. 2. Monte Carlo Particle Transport in Media with Exponentially Varying Time-Dependent Cross Sections

    International Nuclear Information System (INIS)

    We have investigated Monte Carlo schemes for analyzing particle transport through media with exponentially varying time-dependent cross sections. For such media, the cross sections are represented in the form Σ(t) = Σ0 e-at (1) or equivalently as Σ(x) = Σ0 e-bx (2) where b = av and v is the particle speed. For the following discussion, the parameters a and b may be either positive, for exponentially decreasing cross sections, or negative, for exponentially increasing cross sections. For most time-dependent Monte Carlo applications, the time and spatial variations of the cross-section data are handled by means of a stepwise procedure, holding the cross sections constant for each region over a small time interval Δt, performing the Monte Carlo random walk over the interval Δt, updating the cross sections, and then repeating for a series of time intervals. Continuously varying spatial- or time-dependent cross sections can be treated in a rigorous Monte Carlo fashion using delta-tracking, but inefficiencies may arise if the range of cross-section variation is large. In this paper, we present a new method for sampling collision distances directly for cross sections that vary exponentially in space or time. The method is exact and efficient and has direct application to Monte Carlo radiation transport methods. To verify that the probability density function (PDF) is correct and that the random-sampling procedure yields correct results, numerical experiments were performed using a one-dimensional Monte Carlo code. The physical problem consisted of a beam source impinging on a purely absorbing infinite slab, with a slab thickness of 1 cm and Σ0 = 1 cm-1. Monte Carlo calculations with 10 000 particles were run for a range of the exponential parameter b from -5 to +20 cm-1. Two separate Monte Carlo calculations were run for each choice of b, a continuously varying case using the random-sampling procedures described earlier, and a 'conventional' case where the

  16. HEXANN-EVALU - a Monte Carlo program system for pressure vessel neutron irradiation calculation

    International Nuclear Information System (INIS)

    The Monte Carlo program HEXANN and the evaluation program EVALU are intended to calculate Monte Carlo estimates of reaction rates and currents in segments of concentric angular regions around a hexagonal reactor-core region. The report describes the theoretical basis, structure and activity of the programs. Input data preparation guides and a sample problem are also included. Theoretical considerations as well as numerical experimental results suggest the user a nearly optimum way of making use of the Monte Carlo efficiency increasing options included in the program

  17. Neutronics computational methods for cores

    International Nuclear Information System (INIS)

    This engineering-oriented publication contains a detailed presentation of neutronics computational methods for cores. More precisely, it presents neutronics equations: Boltzmann equation for neutron transport, resolution principles, use of high performance computing. The next parts present the problematic (values to be computed, computation software and methods), nuclear data and their processing. Then the authors describe the application of the Monte Carlo method to reactor physics: resolution of the transport equation by the Monte Carlo method, convergence of a Monte Carlo calculation and notion of quality factor, and software. Deterministic methods are then addressed: discretization, processing of resonant absorption, network calculations, core calculation, deterministic software, fuel evolution, and kinetics. The next chapter addresses multi-physical aspects: necessity of a coupling, principles of neutronic/thermal hydraulic coupling, example of an accidental transient. The last part addresses the checking approach, and neutronics computational code validation

  18. Neutron and gamma ray transport calculations in shielding system

    Energy Technology Data Exchange (ETDEWEB)

    Masukawa, Fumihiro; Sakamoto, Hiroki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-03-01

    In the shields for radiation in nuclear facilities, the penetrating holes of various kinds and irregular shapes are made for the reasons of operation, control and others. These penetrating holes and gaps are filled with air or the substances with relatively small shielding performance, and radiation flows out through them, which is called streaming. As the calculation techniques for the shielding design or analysis related to the streaming problem, there are the calculations by simplified evaluation, transport calculation and Monte Carlo method. In this report, the example of calculation by Monte Carlo method which is represented by MCNP code is discussed. A number of variance reduction techniques which seem effective for the analysis of streaming problem were tried. As to the investigation of the applicability of MCNP code to streaming analysis, the object of analysis which are the concrete walls without hole and with horizontal hole, oblique hole and bent oblique hole, the analysis procedure, the composition of concrete, and the conversion coefficient of dose equivalent, and the results of analysis are reported. As for variance reduction technique, cell importance was adopted. (K.I.)

  19. Monte-Carlo simulation of soil carbon measurements by inelastic neutron scattering

    Science.gov (United States)

    Measuring soil carbon is critical for assessing the potential impact of different land management practices on carbon sequestration. The inelastic neutron scattering (INS) of fast neutrons (with energy around 14 MeV) on carbon-12 nuclei produces gamma rays with energy of 4.43 MeV; this gamma flux ca...

  20. Monte Carlo simulation of a very high resolution thermal neutron detector composed of glass scintillator microfibers

    CERN Document Server

    Yushou, Song; Zhang, Xiaodong; Hayward, Jason P

    2016-01-01

    In order to develop a high spatial resolution (micron level) thermal neutron detector, a detector assembly composed of cerium doped lithium glass microfibers, each with a diameter of 1\\,$\\mu$m, is proposed, where the neutron absorption location is reconstructed from the observed charged particle products that result from neutron absorption. To suppress the cross talk of the scintillation light, each scintillating fiber is surrounded by air-filled glass capillaries with the same diameter as the fiber. This pattern is repeated to form a bulk microfiber detector. On one end, the surface of the detector is painted with a thin optical reflector to increase the light collection efficiency at the other end. Then the scintillation light emitted by any neutron interaction is transmitted to one end, magnified, and recorded by an intensified CCD camera. A simulation based on the Geant4 toolkit was developed to model this detector. All the relevant physics processes including neutron interaction, scintillation, and optic...

  1. Thermoluminescence dosimetry of a thermal neutron field and comparison with Monte Carlo calculations.

    Science.gov (United States)

    Fernandes, A C; Santos, J P; Kling, A; Marques, J G; Gonçalves, I C; Carvalho, A Ferro; Santos, L; Cardoso, J; Osvay, M

    2004-01-01

    The characteristics of thermoluminescence dosemeters (TLDs) regarding the determination of photon and neutron absorbed doses were investigated in a thermal neutron beam. Harshaw TLD-100 (LiF:Mg,Ti) and TLD-700 (7LiF:Mg,Ti) were compared with similar materials from Solid Dosimetric Detector and Method Laboratory (People's Republic of China). Harshaw TLD-700H (7LiF:Mg,Cu,P) and aluminium oxide (Al2O3:Mg,Y) from Hungary were also considered for photon dose measurement. The neutron sensitivity of the investigated materials was measured and found to be consistent with values reported by other authors. A comparison was made between the TL dose measurements and results obtained via conventional methods. An agreement within 20% was obtained, which demonstrates the ability of TLD for measuring neutron and photon doses in a mixed field, using careful calibration procedures and determining the neutron sensitivity for the usage conditions. PMID:15367765

  2. An object-oriented implementation of a parallel Monte Carlo code for radiation transport

    Science.gov (United States)

    Santos, Pedro Duarte; Lani, Andrea

    2016-05-01

    This paper describes the main features of a state-of-the-art Monte Carlo solver for radiation transport which has been implemented within COOLFluiD, a world-class open source object-oriented platform for scientific simulations. The Monte Carlo code makes use of efficient ray tracing algorithms (for 2D, axisymmetric and 3D arbitrary unstructured meshes) which are described in detail. The solver accuracy is first verified in testcases for which analytical solutions are available, then validated for a space re-entry flight experiment (i.e. FIRE II) for which comparisons against both experiments and reference numerical solutions are provided. Through the flexible design of the physical models, ray tracing and parallelization strategy (fully reusing the mesh decomposition inherited by the fluid simulator), the implementation was made efficient and reusable.

  3. Implementation, capabilities, and benchmarking of Shift, a massively parallel Monte Carlo radiation transport code

    Science.gov (United States)

    Pandya, Tara M.; Johnson, Seth R.; Evans, Thomas M.; Davidson, Gregory G.; Hamilton, Steven P.; Godfrey, Andrew T.

    2016-03-01

    This work discusses the implementation, capabilities, and validation of Shift, a massively parallel Monte Carlo radiation transport package authored at Oak Ridge National Laboratory. Shift has been developed to scale well from laptops to small computing clusters to advanced supercomputers and includes features such as support for multiple geometry and physics engines, hybrid capabilities for variance reduction methods such as the Consistent Adjoint-Driven Importance Sampling methodology, advanced parallel decompositions, and tally methods optimized for scalability on supercomputing architectures. The scaling studies presented in this paper demonstrate good weak and strong scaling behavior for the implemented algorithms. Shift has also been validated and verified against various reactor physics benchmarks, including the Consortium for Advanced Simulation of Light Water Reactors' Virtual Environment for Reactor Analysis criticality test suite and several Westinghouse AP1000® problems presented in this paper. These benchmark results compare well to those from other contemporary Monte Carlo codes such as MCNP5 and KENO.

  4. The application of Monte Carlo method to electron and photon beams transport; Zastosowanie metody Monte Carlo do analizy transportu elektronow i fotonow

    Energy Technology Data Exchange (ETDEWEB)

    Zychor, I. [Soltan Inst. for Nuclear Studies, Otwock-Swierk (Poland)

    1994-12-31

    The application of a Monte Carlo method to study a transport in matter of electron and photon beams is presented, especially for electrons with energies up to 18 MeV. The SHOWME Monte Carlo code, a modified version of GEANT3 code, was used on the CONVEX C3210 computer at Swierk. It was assumed that an electron beam is mono directional and monoenergetic. Arbitrary user-defined, complex geometries made of any element or material can be used in calculation. All principal phenomena occurring when electron beam penetrates the matter are taken into account. The use of calculation for a therapeutic electron beam collimation is presented. (author). 20 refs, 29 figs.

  5. Thermal neutron response of a boron-coated GEM detector via GEANT4 Monte Carlo code

    International Nuclear Information System (INIS)

    In this work, we report the design configuration and the performance of the hybrid Gas Electron Multiplier (GEM) detector. In order to make the detector sensitive to thermal neutrons, the forward electrode of the GEM has been coated with the enriched boron-10 material, which works as a neutron converter. A total of 5×5 cm2 configuration of GEM has been used for thermal neutron studies. The response of the detector has been estimated via using GEANT4 MC code with two different physics lists. Using the QGSPBICHP physics list, the neutron detection efficiency was determined to be about 3%, while with QGSPBERTHP physics list the efficiency was around 2.5%, at the incident thermal neutron energies of 25 meV. The higher response of the detector proves that GEM-coated with boron converter improves the efficiency for thermal neutrons detection. - Highlights: • The results of boron-coated GEM for thermal neutrons are described. • The simulations were performed by GEANT4 MC code. • The evaluation was determined by GEANT4 using two physics lists. • The response of the detector was taken for En=25–100 meV

  6. Monte Carlo Study of Temperature-dependent Non-diffusive Thermal Transport in Si Nanowires

    CERN Document Server

    Ma, Lei; Liu, Mengmeng; Zhao, Xuxin; Wu, Qixing; Sun, Hongyuan

    2016-01-01

    Non-diffusive thermal transport has gained extensive research interest recently due to its important implications on fundamental understanding of material phonon mean free path distributions and many nanoscale energy applications. In this work, we systematically investigate the role of boundary scattering and nanowire length on the nondiffusive thermal transport in thin silicon nanowires by rigorously solving the phonon Boltzmann transport equation using a variance reduced Monte Carlo technique across a range of temperatures. The simulations use the complete phonon dispersion and spectral lifetime data obtained from first-principle density function theory calculations as input without any adjustable parameters. Our BTE simulation results show that the nanowire length plays an important role in determining the thermal conductivity of silicon nanowires. In addition, our simulation results suggest significant phonon confinement effect for the previously measured silicon nanowires. These findings are important fo...

  7. METHES: A Monte Carlo collision code for the simulation of electron transport in low temperature plasmas

    Science.gov (United States)

    Rabie, M.; Franck, C. M.

    2016-06-01

    We present a freely available MATLAB code for the simulation of electron transport in arbitrary gas mixtures in the presence of uniform electric fields. For steady-state electron transport, the program provides the transport coefficients, reaction rates and the electron energy distribution function. The program uses established Monte Carlo techniques and is compatible with the electron scattering cross section files from the open-access Plasma Data Exchange Project LXCat. The code is written in object-oriented design, allowing the tracing and visualization of the spatiotemporal evolution of electron swarms and the temporal development of the mean energy and the electron number due to attachment and/or ionization processes. We benchmark our code with well-known model gases as well as the real gases argon, N2, O2, CF4, SF6 and mixtures of N2 and O2.

  8. Chemical composition of the lunar surface from neutron leakage fluxes%Chemical composition of the lunar surface from neutron leakage fluxes

    Institute of Scientific and Technical Information of China (English)

    程宇; 黄铁矿; 董武东; 任中洲; 许敖敖

    2011-01-01

    The neutron leakage fluxes from the lunar surface are calculated by Monte Carlo transport code based on Geant4. The integral fluxes of fast neutrons, epi-thermal neutrons and thermal neutrons are analyzed. Numerical results for 20 kinds of lunar soils and

  9. Srna-Monte Carlo codes for proton transport simulation in combined and voxelized geometries

    International Nuclear Information System (INIS)

    This paper describes new Monte Carlo codes for proton transport simulations in complex geometrical forms and in materials of different composition. The SRNA codes were developed for three dimensional (3D) dose distribution calculation in proton therapy and dosimetry. The model of these codes is based on the theory of proton multiple scattering and a simple model of compound nucleus decay. The developed package consists of two codes: SRNA-2KG and SRNA-VOX. The first code simulates proton transport in combined geometry that can be described by planes and second order surfaces. The second one uses the voxelized geometry of material zones and is specifically adopted for the application of patient computer tomography data. Transition probabilities for both codes are given by the SRNADAT program. In this paper, we will present the models and algorithms of our programs, as well as the results of the numerical experiments we have carried out applying them, along with the results of proton transport simulation obtained through the PETRA and GEANT programs. The simulation of the proton beam characterization by means of the Multi-Layer Faraday Cup and spatial distribution of positron emitters obtained by our program indicate the imminent application of Monte Carlo techniques in clinical practice. (author)

  10. Srna - Monte Carlo codes for proton transport simulation in combined and voxelized geometries

    Directory of Open Access Journals (Sweden)

    Ilić Radovan D.

    2002-01-01

    Full Text Available This paper describes new Monte Carlo codes for proton transport simulations in complex geometrical forms and in materials of different composition. The SRNA codes were developed for three dimensional (3D dose distribution calculation in proton therapy and dosimetry. The model of these codes is based on the theory of proton multiple scattering and a simple model of compound nucleus decay. The developed package consists of two codes: SRNA-2KG and SRNA-VOX. The first code simulates proton transport in combined geometry that can be described by planes and second order surfaces. The second one uses the voxelized geometry of material zones and is specifically adopted for the application of patient computer tomography data. Transition probabilities for both codes are given by the SRNADAT program. In this paper, we will present the models and algorithms of our programs, as well as the results of the numerical experiments we have carried out applying them, along with the results of proton transport simulation obtained through the PETRA and GEANT programs. The simulation of the proton beam characterization by means of the Multi-Layer Faraday Cup and spatial distribution of positron emitters obtained by our program indicate the imminent application of Monte Carlo techniques in clinical practice.

  11. Piecewise linear discretization of Symbolic Implicit Monte Carlo radiation transport in the difference formulation

    Energy Technology Data Exchange (ETDEWEB)

    Brooks III, E D; Szoke, A; Peterson, J L

    2005-11-15

    We describe a Monte Carlo solution for time dependent photon transport, in the difference formulation with the material in local thermodynamic equilibrium (LTE), that is piecewise linear in its treatment of the material state variable. Our method employs a Galerkin solution for the material energy equation while using Symbolic Implicit Monte Carlo (SIMC) to solve the transport equation. In constructing the scheme, one has the freedom to choose between expanding the material temperature, or the equivalent black body radiation energy density at the material temperature, in terms of finite element basis functions. The former provides a linear treatment of the material energy while the latter provides a linear treatment of the radiative coupling between zones. Subject to the conditional use of a lumped material energy in the vicinity of strong gradients, possible with a linear treatment of the material energy, our approach provides a robust solution for time dependent transport of thermally emitted radiation that can address a wide range of problems. It produces accurate results in the diffusion limit.

  12. Development of a Monte Carlo software to photon transportation in voxel structures using graphic processing units

    International Nuclear Information System (INIS)

    As the most accurate method to estimate absorbed dose in radiotherapy, Monte Carlo Method (MCM) has been widely used in radiotherapy treatment planning. Nevertheless, its efficiency can be improved for clinical routine applications. In this thesis, the CUBMC code is presented, a GPU-based MC photon transport algorithm for dose calculation under the Compute Unified Device Architecture (CUDA) platform. The simulation of physical events is based on the algorithm used in PENELOPE, and the cross section table used is the one generated by the MATERIAL routine, also present in PENELOPE code. Photons are transported in voxel-based geometries with different compositions. There are two distinct approaches used for transport simulation. The rst of them forces the photon to stop at every voxel frontier, the second one is the Woodcock method, where the photon ignores the existence of borders and travels in homogeneous fictitious media. The CUBMC code aims to be an alternative of Monte Carlo simulator code that, by using the capability of parallel processing of graphics processing units (GPU), provide high performance simulations in low cost compact machines, and thus can be applied in clinical cases and incorporated in treatment planning systems for radiotherapy. (author)

  13. Gamma transport and diffusion calculation capability coupled with neutron transport simulation in KARMA 1.2

    International Nuclear Information System (INIS)

    Highlights: ► We have extended the KAERI library generation system to include gamma cross section generation capability. ► A gamma transport/diffusion calculation module has been implemented in KARMA 1.2. ► The computational results for benchmark problems show that the gamma library and gamma simulation in KARMA are reasonable. - Abstract: KAERI has developed a lattice transport calculation code KARMA (Kernel Analyzer by Ray-tracing Method for fuel Assembly) and its library generation system. Recently, the library generation system has been extended to include a gamma cross section generation capability and a gamma transport/diffusion calculation module has been implemented in KARMA 1.2. The method of characteristics for the neutron transport calculation to estimate eigenvalue has been utilized to predict gamma flux distribution and energy deposition. In addition, the coarse mesh finite difference method with diffusion approximation has also been utilized to estimate gamma flux distribution and energy depositions for each coarse mesh with homogenized pins as a computationally efficient alternative. This paper describes the procedure to generate neutron induced gamma production and gamma cross section data, and the methods to predict gamma flux distribution, gamma energy deposition and gamma smeared pin power distribution. The computational results for benchmark problems show that the gamma library and gamma simulation in KARMA are reasonable. And it is noted that gamma smeared power distributions predicted by coarse mesh diffusion calculation are very accurate compared to the results of transport calculation

  14. Monte Carlo simulation of a very high resolution thermal neutron detector composed of glass scintillator microfibers.

    Science.gov (United States)

    Song, Yushou; Conner, Joseph; Zhang, Xiaodong; Hayward, Jason P

    2016-02-01

    In order to develop a high spatial resolution (micron level) thermal neutron detector, a detector assembly composed of cerium doped lithium glass microfibers, each with a diameter of 1 μm, is proposed, where the neutron absorption location is reconstructed from the observed charged particle products that result from neutron absorption. To suppress the cross talk of the scintillation light, each scintillating fiber is surrounded by air-filled glass capillaries with the same diameter as the fiber. This pattern is repeated to form a bulk microfiber detector. On one end, the surface of the detector is painted with a thin optical reflector to increase the light collection efficiency at the other end. Then the scintillation light emitted by any neutron interaction is transmitted to one end, magnified, and recorded by an intensified CCD camera. A simulation based on the Geant4 toolkit was developed to model this detector. All the relevant physics processes including neutron interaction, scintillation, and optical boundary behaviors are simulated. This simulation was first validated through measurements of neutron response from lithium glass cylinders. With good expected light collection, an algorithm based upon the features inherent to alpha and triton particle tracks is proposed to reconstruct the neutron reaction position in the glass fiber array. Given a 1 μm fiber diameter and 0.1mm detector thickness, the neutron spatial resolution is expected to reach σ∼1 μm with a Gaussian fit in each lateral dimension. The detection efficiency was estimated to be 3.7% for a glass fiber assembly with thickness of 0.1mm. When the detector thickness increases from 0.1mm to 1mm, the position resolution is not expected to vary much, while the detection efficiency is expected to increase by about a factor of ten.

  15. New Capabilities in Mercury: A Modern, Monte Carlo Particle Transport Code

    Energy Technology Data Exchange (ETDEWEB)

    Procassini, R J; Cullen, D E; Greenman, G M; Hagmann, C A; Kramer, K J; McKinley, M S; O' Brien, M J; Taylor, J M

    2007-03-08

    The new physics, algorithmic and computer science capabilities of the Mercury general-purpose Monte Carlo particle transport code are discussed. The new physics and algorithmic features include in-line energy deposition and isotopic depletion, significant enhancements to the tally and source capabilities, diagnostic ray-traced particles, support for multi-region hybrid (mesh and combinatorial geometry) systems, and a probability of initiation method. Computer science enhancements include a second method of dynamically load-balancing parallel calculations, improved methods for visualizing 3-D combinatorial geometries and initial implementation of an in-line visualization capabilities.

  16. Neutron transport and Montecarlo method: analysis and revision

    International Nuclear Information System (INIS)

    The resolution of the neutron transport equation by the Montecarlo method is presented. Coming from an extensive discussion on the best formulation of that equation in order to be treated through the mentioned method, the theoretical bases of the estimator and random-walk generation is extensively explained. The most general expression for the estimators in different physical situations, each with a diverse random-walk, is included in this basical theoretical part. Furthemore, a large revision on the variance reduction methods is made. Its theoretical presentation is claimed to be in connection with the need for each one of them. The use of the adjoint equation, as a part of the importance sampling, Russian Roulette, splitting, exponential transform, conditional and correlated Montecarlo, and one-collision and next-event extimators, are discussed. Finally, come comments in the presentation of the last works on the theoretical prediction of errors in the generation of estimators-random walks are made. (author)

  17. Parallel processing of neutron transport in fuel assembly calculation

    International Nuclear Information System (INIS)

    Group constants, which are used for reactor analyses by nodal method, are generated by fuel assembly calculations based on the neutron transport theory, since one or a quarter of the fuel assembly corresponds to a unit mesh in the current nodal calculation. The group constant calculation for a fuel assembly is performed through spectrum calculations, a two-dimensional fuel assembly calculation, and depletion calculations. The purpose of this study is to develop a parallel algorithm to be used in a parallel processor for the fuel assembly calculation and the depletion calculations of the group constant generation. A serial program, which solves the neutron integral transport equation using the transmission probability method and the linear depletion equation, was prepared and verified by a benchmark calculation. Small changes from the serial program was enough to parallelize the depletion calculation which has inherent parallel characteristics. In the fuel assembly calculation, however, efficient parallelization is not simple and easy because of the many coupling parameters in the calculation and data communications among CPU's. In this study, the group distribution method is introduced for the parallel processing of the fuel assembly calculation to minimize the data communications. The parallel processing was performed on Quadputer with 4 CPU's operating in NURAD Lab. at KAIST. Efficiencies of 54.3 % and 78.0 % were obtained in the fuel assembly calculation and depletion calculation, respectively, which lead to the overall speedup of about 2.5. As a result, it is concluded that the computing time consumed for the group constant generation can be easily reduced by parallel processing on the parallel computer with small size CPU's

  18. An Advanced Neutronic Analysis Toolkit with Inline Monte Carlo capability for BHTR Analysis

    Energy Technology Data Exchange (ETDEWEB)

    William R. Martin; John C. Lee

    2009-12-30

    Monte Carlo capability has been combined with a production LWR lattice physics code to allow analysis of high temperature gas reactor configurations, accounting for the double heterogeneity due to the TRISO fuel. The Monte Carlo code MCNP5 has been used in conjunction with CPM3, which was the testbench lattice physics code for this project. MCNP5 is used to perform two calculations for the geometry of interest, one with homogenized fuel compacts and the other with heterogeneous fuel compacts, where the TRISO fuel kernels are resolved by MCNP5.

  19. Radiation Transport for Explosive Outflows: A Multigroup Hybrid Monte Carlo Method

    Science.gov (United States)

    Wollaeger, Ryan T.; van Rossum, Daniel R.; Graziani, Carlo; Couch, Sean M.; Jordan, George C., IV; Lamb, Donald Q.; Moses, Gregory A.

    2013-12-01

    We explore Implicit Monte Carlo (IMC) and discrete diffusion Monte Carlo (DDMC) for radiation transport in high-velocity outflows with structured opacity. The IMC method is a stochastic computational technique for nonlinear radiation transport. IMC is partially implicit in time and may suffer in efficiency when tracking MC particles through optically thick materials. DDMC accelerates IMC in diffusive domains. Abdikamalov extended IMC and DDMC to multigroup, velocity-dependent transport with the intent of modeling neutrino dynamics in core-collapse supernovae. Densmore has also formulated a multifrequency extension to the originally gray DDMC method. We rigorously formulate IMC and DDMC over a high-velocity Lagrangian grid for possible application to photon transport in the post-explosion phase of Type Ia supernovae. This formulation includes an analysis that yields an additional factor in the standard IMC-to-DDMC spatial interface condition. To our knowledge the new boundary condition is distinct from others presented in prior DDMC literature. The method is suitable for a variety of opacity distributions and may be applied to semi-relativistic radiation transport in simple fluids and geometries. Additionally, we test the code, called SuperNu, using an analytic solution having static material, as well as with a manufactured solution for moving material with structured opacities. Finally, we demonstrate with a simple source and 10 group logarithmic wavelength grid that IMC-DDMC performs better than pure IMC in terms of accuracy and speed when there are large disparities between the magnitudes of opacities in adjacent groups. We also present and test our implementation of the new boundary condition.

  20. Neutron analysis of spent fuel storage installation using parallel computing and advance discrete ordinates and Monte Carlo techniques.

    Science.gov (United States)

    Shedlock, Daniel; Haghighat, Alireza

    2005-01-01

    In the United States, the Nuclear Waste Policy Act of 1982 mandated centralised storage of spent nuclear fuel by 1988. However, the Yucca Mountain project is currently scheduled to start accepting spent nuclear fuel in 2010. Since many nuclear power plants were only designed for -10 y of spent fuel pool storage, > 35 plants have been forced into alternate means of spent fuel storage. In order to continue operation and make room in spent fuel pools, nuclear generators are turning towards independent spent fuel storage installations (ISFSIs). Typical vertical concrete ISFSIs are -6.1 m high and 3.3 m in diameter. The inherently large system, and the presence of thick concrete shields result in difficulties for both Monte Carlo (MC) and discrete ordinates (SN) calculations. MC calculations require significant variance reduction and multiple runs to obtain a detailed dose distribution. SN models need a large number of spatial meshes to accurately model the geometry and high quadrature orders to reduce ray effects, therefore, requiring significant amounts of computer memory and time. The use of various differencing schemes is needed to account for radial heterogeneity in material cross sections and densities. Two P3, S12, discrete ordinate, PENTRAN (parallel environment neutral-particle TRANsport) models were analysed and different MC models compared. A multigroup MCNP model was developed for direct comparison to the SN models. The biased A3MCNP (automated adjoint accelerated MCNP) and unbiased (MCNP) continuous energy MC models were developed to assess the adequacy of the CASK multigroup (22 neutron, 18 gamma) cross sections. The PENTRAN SN results are in close agreement (5%) with the multigroup MC results; however, they differ by -20-30% from the continuous-energy MC predictions. This large difference can be attributed to the expected difference between multigroup and continuous energy cross sections, and the fact that the CASK library is based on the old ENDF

  1. Production of neutron cross section library based on JENDL-4.0 to continuous-energy Monte Carlo code MVP and its application to criticality analysis of benchmark problems in the ICSBEP handbook

    International Nuclear Information System (INIS)

    In May 2010, JENDL-4.0 was released from Japan Atomic Energy Agency as the updated Japanese Nuclear Data Library. It was processed by the nuclear data processing system LICEM and an arbitrary-temperature neutron cross section library MVPlib-nJ40 was produced for the neutron and photon transport calculation code MVP based on the continuous-energy Monte Carlo method. The library contains neutron cross sections for 406 nuclides on the free gas model, thermal scattering cross sections, and cross sections of pseudo fission products for burn-up calculations with MVP. Criticality benchmark calculations were carried out with MVP and MVPlib-nJ40 for about 1,000 cases of critical experiments stored in the hand book of International Criticality Safety Benchmark Evaluation Project (ICSBEP), which covers a wide variety of fuel materials, fuel forms, and neutron spectra. We report all comparison results (C/E values) of effective neutron multiplication factors between calculations and experiments to give a validation data for the prediction accuracy of JENDL-4.0 for criticalities. (author)

  2. Assessment of the neutron emission anisotropy factor of a sealed AmBe source by means of measurements and Monte Carlo simulations

    Energy Technology Data Exchange (ETDEWEB)

    Loreti, S.; Pietropaolo, A., E-mail: antonino.pietropaolo@enea.it

    2015-10-11

    The neutron emission anisotropy factor of a sealed Americium–Beryllium source is experimentally determined and compared to Monte Carlo simulations. The measurements were done at the Italian Institute for Metrology of Ionizing Radiations using a long counter neutron detector and a “X.3” type AmBe sealed neutron source. Experimental data are compared to simulations performed with the MCNP code where the precise structure of the source is taken into account starting from its technical design. The contributions of the single structural parts are described to point out the effective sources of the emission anisotropy.

  3. Experimental study and Monte Carlo modeling of operational quantities in metrology of ionizing radiation: application to neutrons dosimetry by radio-photoluminescence

    International Nuclear Information System (INIS)

    We characterize a passive dosimeter capable of measuring both fast and thermal neutrons for ambient and personal dosimetry. These neutrons can be detected in a mixed neutron-gamma field with appropriate converters (polyethylene for fast neutrons, cadmium for thermal neutrons). Monte Carlo simulations with MCNPX helped with the geometrical conception of the dosimeter and the choice of materials. The responses of the RPL dosimeter to these neutrons are linear in H*(10) and Hp(10) with detection limits of 2 mSv for fast neutrons and 0.19 mSv for thermal neutrons. The angular dependencies are satisfactory according to the ISO 21909 norm. A calibration factor of (9.5 ± 0.5)*10-2 mSv.cm2/RPL signal is obtained to the fast neutrons of the IPHC's 241Am-Be calibrator. This factor is (9.7 ± 0.3)*10-3 mSv.cm2/RPL signal for the thermalized neutrons. (author)

  4. Atomic structure of glassy Mg60Cu30Y10 investigated with EXAFS, x-ray and neutron diffraction, and reverse Monte Carlo simulations

    DEFF Research Database (Denmark)

    Jovari, P.; Saksl, K.; Pryds, Nini;

    2007-01-01

    Short range order of amorphous Mg60Cu30Y10 was investigated by x-ray and neutron diffraction, Cu and Y K-edge x-ray absorption fine structure measurements, and the reverse Monte Carlo simulation technique. We found that Mg-Mg and Mg-Cu nearest neighbor distances are very similar to values found i...

  5. Ge(Li) intrinsic efficiency calculation using Monte Carlo simulation for γ radiation transport

    International Nuclear Information System (INIS)

    To solve a radiation transport problem by using Monte Carlo simulation method, the evolution of a large number of radiations must be simulated and also the analysis of their history must be done. The evolution of a radiation starts by the radiation emission, followed by the radiation unperturbed propagation in the medium between the successive interactions and then the radiation parameters modification in the points where interactions occur. The goal of this paper consists in the calculation of the total detection efficiency and the intrinsic efficiency for a coaxial Ge(Li) detector, using Monte Carlo method in order to simulate the γ radiation transport. A Ge(Li) detector with 106 cm3 active volume and γ photons with energies in 50 keV - 2 MeV range, emitted by a point source situated on the detector axis, were considered. Each γ photon evolution is simulated by an analogue process step-by-step until the photon escapes from the detector or is completely absorbed in the active volume of the detector. (author)

  6. Particle Communication and Domain Neighbor Coupling: Scalable Domain Decomposed Algorithms for Monte Carlo Particle Transport

    International Nuclear Information System (INIS)

    In order to run Monte Carlo particle transport calculations on new supercomputers with hundreds of thousands or millions of processors, care must be taken to implement scalable algorithms. This means that the algorithms must continue to perform well as the processor count increases. In this paper, we examine the scalability of: (1) globally resolving the particle locations on the correct processor, (2) deciding that particle streaming communication has finished, and (3) efficiently coupling neighbor domains together with different replication levels. We have run domain decomposed Monte Carlo particle transport on up to 221 = 2,097,152 MPI processes on the IBM BG/Q Sequoia supercomputer and observed scalable results that agree with our theoretical predictions. These calculations were carefully constructed to have the same amount of work on every processor, i.e. the calculation is already load balanced. We also examine load imbalanced calculations where each domain's replication level is proportional to its particle workload. In this case we show how to efficiently couple together adjacent domains to maintain within workgroup load balance and minimize memory usage.

  7. Particle Communication and Domain Neighbor Coupling: Scalable Domain Decomposed Algorithms for Monte Carlo Particle Transport

    Energy Technology Data Exchange (ETDEWEB)

    O' Brien, M. J.; Brantley, P. S.

    2015-01-20

    In order to run Monte Carlo particle transport calculations on new supercomputers with hundreds of thousands or millions of processors, care must be taken to implement scalable algorithms. This means that the algorithms must continue to perform well as the processor count increases. In this paper, we examine the scalability of:(1) globally resolving the particle locations on the correct processor, (2) deciding that particle streaming communication has finished, and (3) efficiently coupling neighbor domains together with different replication levels. We have run domain decomposed Monte Carlo particle transport on up to 221 = 2,097,152 MPI processes on the IBM BG/Q Sequoia supercomputer and observed scalable results that agree with our theoretical predictions. These calculations were carefully constructed to have the same amount of work on every processor, i.e. the calculation is already load balanced. We also examine load imbalanced calculations where each domain’s replication level is proportional to its particle workload. In this case we show how to efficiently couple together adjacent domains to maintain within workgroup load balance and minimize memory usage.

  8. A 'local' exponential transform method for global variance reduction in Monte Carlo transport problems

    International Nuclear Information System (INIS)

    We develop a 'Local' Exponential Transform method which distributes the particles nearly uniformly across the system in Monte Carlo transport calculations. An exponential approximation to the continuous transport equation is used in each mesh cell to formulate biasing parameters. The biasing parameters, which resemble those of the conventional exponential transform, tend to produce a uniform sampling of the problem geometry when applied to a forward Monte Carlo calculation, and thus they help to minimize the maximum variance of the flux. Unlike the conventional exponential transform, the biasing parameters are spatially dependent, and are automatically determined from a forward diffusion calculation. We develop two versions of the forward Local Exponential Transform method, one with spatial biasing only, and one with spatial and angular biasing. The method is compared to conventional geometry splitting/Russian roulette for several sample one-group problems in X-Y geometry. The forward Local Exponential Transform method with angular biasing is found to produce better results than geometry splitting/Russian roulette in terms of minimizing the maximum variance of the flux. (orig.)

  9. 3D imaging using combined neutron-photon fan-beam tomography: A Monte Carlo study.

    Science.gov (United States)

    Hartman, J; Yazdanpanah, A Pour; Barzilov, A; Regentova, E

    2016-05-01

    The application of combined neutron-photon tomography for 3D imaging is examined using MCNP5 simulations for objects of simple shapes and different materials. Two-dimensional transmission projections were simulated for fan-beam scans using 2.5MeV deuterium-deuterium and 14MeV deuterium-tritium neutron sources, and high-energy X-ray sources, such as 1MeV, 6MeV and 9MeV. Photons enable assessment of electron density and related mass density, neutrons aid in estimating the product of density and material-specific microscopic cross section- the ratio between the two provides the composition, while CT allows shape evaluation. Using a developed imaging technique, objects and their material compositions have been visualized. PMID:26953978

  10. Predicting fissile content of spent nuclear fuel assemblies with the Passive Neutron Albedo Reactivity technique and Monte Carlo code emulation

    International Nuclear Information System (INIS)

    There is a great need in the safeguards community to be able to nondestructively quantify the mass of plutonium of a spent nuclear fuel assembly. As part of the Next Generation of Safeguards Initiative, we are investigating several techniques, or detector systems, which, when integrated, will be capable of quantifying the plutonium mass of a spent fuel assembly without dismantling the assembly. This paper reports on the simulation of one of these techniques, the Passive Neutron Albedo Reactivity with Fission Chambers (PNAR-FC) system. The response of this system over a wide range of spent fuel assemblies with different burnup, initial enrichment, and cooling time characteristics is shown. A Monte Carlo method of using these modeled results to estimate the fissile content of a spent fuel assembly has been developed. A few numerical simulations of using this method are shown. Finally, additional developments still needed and being worked on are discussed. (author)

  11. Predicting fissile content of spent nuclear fuel assemblies with the passive neutron Albedo reactivity technique and Monte Carlo code emulation

    International Nuclear Information System (INIS)

    There is a great need in the safeguards community to be able to nondestructively quantify the mass of plutonium of a spent nuclear fuel assembly. As part of the Next Generation of Safeguards Initiative, we are investigating several techniques, or detector systems, which, when integrated, will be capable of quantifying the plutonium mass of a spent fuel assembly without dismantling the assembly. This paper reports on the simulation of one of these techniques, the Passive Neutron Albedo Reactivity with Fission Chambers (PNAR-FC) system. The response of this system over a wide range of spent fuel assemblies with different burnup, initial enrichment, and cooling time characteristics is shown. A Monte Carlo method of using these modeled results to estimate the fissile content of a spent fuel assembly has been developed. A few numerical simulations of using this method are shown. Finally, additional developments still needed and being worked on are discussed.

  12. Borehole prompt gamma neutron activation and comparison with Monte Carlo simulation using MCNP code Borehole PGNAA experiment comparison with MCNP

    Energy Technology Data Exchange (ETDEWEB)

    Sohrabpour, M. [Gamma Irradiation Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of); Shahriari, M. [Physics Department, Amir Kabir University of Technology, Tehran (Iran, Islamic Republic of); Zarifian, V.; Moghadam, K.K. [Nuclear Research Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of)

    1999-04-01

    A borehole experiment using prompt gamma neutron activation analysis has been performed in a large sample box having a volume of 1 m{sup 3}. Brine solutions having a salt concentration in the range of 0-10 wt% of sodium chloride has been used. Chlorine prompt gamma spectral response as a function of the salt concentrations have been obtained. A simulation of the above experiments has also been carried out using the MCNP4A Monte Carlo code. Comparison of the experimental spectral response versus the simulated MCNP4A data has produced excellent agreement. In view of the good benchmark data it is proposed that due to the inherent problems associated with the ordinary calibration procedures for the borehole logging tools, one could employ a combined calibration/simulation scheme to circumvent these difficulties and achieve more effective results.

  13. An inner-crystal neutron-scatter camera: Monte carlo simulation

    Science.gov (United States)

    Jo, Ajin; Lee, Wonho

    2016-05-01

    Neutron energy emitted from special nuclear materials (SNMs) can be measured by using neutronproton scattering; also, the scattering angle can be calculated from the ratio of the scattered energy to the incident energy. By using position and energy information, we can image the original source position by using the backprojection and list-mode maximum-likelihood expectation maximization (MLEM) method. In this paper, we propose an inner-crystal neutron scatter camera system in which the detectors are not separated to obtain interactions at a variety of scatter angles; based on this system, we analyzed the characteristics of the corresponding neutron-scattering camera. The factors that affected the neutron-scatter image were the neutron velocity after scattering, the cut-off level of the time of flight (ToF), and the width of the cones used for image reconstruction. To determine the optimal point for the reconstruction of an image, we estimated the performance of the system by using the figure of merit (FoM). The optimal neutron-velocity (d/ToF) was ~0.3 × 107 m/s according to our simulation result, while the optimal cut-off level of the ToF was 4 ns as the latter minimized the noise while maintaining the required efficiency. The widths of the cones ( ɛ) also affected the full width at half maximum (FWHM) and the noise of the image. In terms of a simple source-geometry, whereby concepts such as "point source" were used, a large e value was suitable to achieve noise reduction; however, regarding the complicated source geometry, a small e value was favorable for precise reconstruction of the original source geometry for both the backprojection and the list-mode MLEM methods.

  14. Characterization of the storage pool of the Neutron Standards Laboratory of CIEMAT, using Monte Carlo techniques

    Energy Technology Data Exchange (ETDEWEB)

    Campo B, X.; Mendez V, R.; Embid S, M. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas, Av. Complutense 40, 28040 Madrid (Spain); Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98060 Zacatecas (Mexico); Sanz G, J., E-mail: xandra.campo@ciemat.es [Universidad Nacional de Educacion a Distancia, Escuela Tecnica Superior de Ingenieros Industriales, C. Juan del Rosal 12, 28040 Madrid (Spain)

    2014-08-15

    Neutron Standards Laboratory of CIEMAT in Spain is a brand new irradiation facility, with {sup 241}Am-Be (185 GBq) and {sup 252}Cf (5 GBq) calibrated neutron sources which are stored in a water pool with a concrete cover. From this storage place an automated system is able to take the selected source and place it in the irradiation position, 4 m over the ground level and in the geometrical center of the Irradiation Room with 9 m (length) x 7.5 m (width) x 8 m (height). For calibration or irradiation purposes, detectors or materials can be placed on a bench but it is possible to use the pool (1.0 m x 1.5 m and more than 1.0 m depth) for long time irradiations in thermal neutron fields. For this reason it is essential to characterize the pool itself in terms of neutron spectrum. In this document, the main features of this facility are presented and the characterization of the storage pool in terms of neutron fluence rate and neutron spectrum has been carried out using simulations with MCNPX-2.7.e code. The MCNPX-2.7.e model has been validated using experimental measurements outside the pool (Bert hold LB6411). Inside the pool, the fluence rate decreases and the spectra is thermalized with the distance to the {sup 252}Cf source. This source predominates and the effect of the {sup 241}Am-Be source in these magnitudes is not shown until positions closer than 20 cm from it. (author)

  15. Monte Carlo analysis of accelerator-driven systems studies on spallation neutron yield and energy gain

    CERN Document Server

    Hashemi-Nezhad, S R; Westmeier, W; Bamblevski, V P; Krivopustov, M I; Kulakov, B A; Sosnin, A N; Wan, J S; Odoj, R

    2001-01-01

    The neutron yield in the interaction of protons with lead and uranium targets has been studied using the LAHET code system. The dependence of the neutron multiplicity on target dimensions and proton energy has been calculated and the dependence of the energy amplification on the proton energy has been investigated in an accelerator-driven system of a given effective multiplication coefficient. Some of the results are compared with experimental findings and with similar calculations by the DCM/CEM code of Dubna and the FLUKA code system used in CERN. (14 refs).

  16. An analysis on changes in reservoir fluid based on numerical simulation of neutron log using a Monte Carlo N-Particle algorithm

    Science.gov (United States)

    Ku, B.; Nam, M.

    2012-12-01

    Neutron logging has been widely used to estimate neutron porosity to evaluate formation properties in oil industry. More recently, neutron logging has been highlighted for monitoring the behavior of CO2 injected into reservoir for geological CO2 sequestration. For a better understanding of neutron log interpretation, Monte Carlo N-Particle (MCNP) algorithm is used to illustrate the response of a neutron tool. In order to obtain calibration curves for the neutron tool, neutron responses are simulated in water-filled limestone, sandstone and dolomite formations of various porosities. Since the salinities (concentration of NaCl) of borehole fluid and formation water are important factors for estimating formation porosity, we first compute and analyze neutron responses for brine-filled formations with different porosities. Further, we consider changes in brine saturation of a reservoir due to hydrocarbon production or geological CO2 sequestration to simulate corresponding neutron logging data. As gas saturation decreases, measured neutron porosity confirms gas effects on neutron logging, which is attributed to the fact that gas has slightly smaller number of hydrogen than brine water. In the meantime, increase in CO2 saturation due to CO2 injection reduces measured neutron porosity giving a clue to estimation the CO2 saturation, since the injected CO2 substitute for the brine water. A further analysis on the reduction gives a strategy for estimating CO2 saturation based on time-lapse neutron logging. This strategy can help monitoring not only geological CO2 sequestration but also CO2 flood for enhanced-oil-recovery. Acknowledgements: This work was supported by the Energy Efficiency & Resources of the Korea Institute of Energy Technology Evaluation and Planning (KETEP) grant funded by the Korea government Ministry of Knowledge Economy (No. 2012T100201588). Myung Jin Nam was partially supported by the National Research Foundation of Korea(NRF) grant funded by the Korea

  17. A Complex-Geometry Validation Experiment for Advanced Neutron Transport Codes

    Energy Technology Data Exchange (ETDEWEB)

    David W. Nigg; Anthony W. LaPorta; Joseph W. Nielsen; James Parry; Mark D. DeHart; Samuel E. Bays; William F. Skerjanc

    2013-11-01

    The Idaho National Laboratory (INL) has initiated a focused effort to upgrade legacy computational reactor physics software tools and protocols used for support of core fuel management and experiment management in the Advanced Test Reactor (ATR) and its companion critical facility (ATRC) at the INL.. This will be accomplished through the introduction of modern high-fidelity computational software and protocols, with appropriate new Verification and Validation (V&V) protocols, over the next 12-18 months. Stochastic and deterministic transport theory based reactor physics codes and nuclear data packages that support this effort include MCNP5[1], SCALE/KENO6[2], HELIOS[3], SCALE/NEWT[2], and ATTILA[4]. Furthermore, a capability for sensitivity analysis and uncertainty quantification based on the TSUNAMI[5] system has also been implemented. Finally, we are also evaluating the Serpent[6] and MC21[7] codes, as additional verification tools in the near term as well as for possible applications to full three-dimensional Monte Carlo based fuel management modeling in the longer term. On the experimental side, several new benchmark-quality code validation measurements based on neutron activation spectrometry have been conducted using the ATRC. Results for the first four experiments, focused on neutron spectrum measurements within the Northwest Large In-Pile Tube (NW LIPT) and in the core fuel elements surrounding the NW LIPT and the diametrically opposite Southeast IPT have been reported [8,9]. A fifth, very recent, experiment focused on detailed measurements of the element-to-element core power distribution is summarized here and examples of the use of the measured data for validation of corresponding MCNP5, HELIOS, NEWT, and Serpent computational models using modern least-square adjustment methods are provided.

  18. The Monte Carlo code CSSE for the simulation of realistic thermal neutron sensor devices for Humanitarian Demining

    Energy Technology Data Exchange (ETDEWEB)

    Palomba, M. E-mail: maurizio.palomba@ba.infn.it; D' Erasmo, G.; Pantaleo, A

    2003-02-11

    The CSSE code, a GEANT3-based Monte Carlo simulation program, has been developed in the framework of the EXPLODET project (Nucl. Instr. and Meth. A 422 (1999) 918) with the aim to simulate experimental set-ups employed in Thermal Neutron Analysis (TNA) for the landmines detection. Such a simulation code appears to be useful for studying the background in the {gamma}-ray spectra obtained with this technique, especially in the region where one expects to find the explosive signature (the {gamma}-ray peak at 10.83 MeV coming from neutron capture by nitrogen). The main features of the CSSE code are introduced and original innovations emphasized. Among the latter, an algorithm simulating the time correlation between primary particles, according with their time distributions is presented. Such a correlation is not usually achievable within standard GEANT-based codes and allows to reproduce some important phenomena, as the pulse pile-up inside the NaI(Tl) {gamma}-ray detector employed, producing a more realistic detector response simulation. CSSE has been successfully tested by reproducing a real nuclear sensor prototype assembled at the Physics Department of Bari University.

  19. Recommended direct simulation Monte Carlo collision model parameters for modeling ionized air transport processes

    Energy Technology Data Exchange (ETDEWEB)

    Swaminathan-Gopalan, Krishnan; Stephani, Kelly A., E-mail: ksteph@illinois.edu [Department of Mechanical Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois 61801 (United States)

    2016-02-15

    A systematic approach for calibrating the direct simulation Monte Carlo (DSMC) collision model parameters to achieve consistency in the transport processes is presented. The DSMC collision cross section model parameters are calibrated for high temperature atmospheric conditions by matching the collision integrals from DSMC against ab initio based collision integrals that are currently employed in the Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) and Data Parallel Line Relaxation (DPLR) high temperature computational fluid dynamics solvers. The DSMC parameter values are computed for the widely used Variable Hard Sphere (VHS) and the Variable Soft Sphere (VSS) models using the collision-specific pairing approach. The recommended best-fit VHS/VSS parameter values are provided over a temperature range of 1000-20 000 K for a thirteen-species ionized air mixture. Use of the VSS model is necessary to achieve consistency in transport processes of ionized gases. The agreement of the VSS model transport properties with the transport properties as determined by the ab initio collision integral fits was found to be within 6% in the entire temperature range, regardless of the composition of the mixture. The recommended model parameter values can be readily applied to any gas mixture involving binary collisional interactions between the chemical species presented for the specified temperature range.

  20. COMET-PE as an Alternative to Monte Carlo for Photon and Electron Transport

    Science.gov (United States)

    Hayward, Robert M.; Rahnema, Farzad

    2014-06-01

    Monte Carlo methods are a central component of radiotherapy treatment planning, shielding design, detector modeling, and other applications. Long calculation times, however, can limit the usefulness of these purely stochastic methods. The coarse mesh method for photon and electron transport (COMET-PE) provides an attractive alternative. By combining stochastic pre-computation with a deterministic solver, COMET-PE achieves accuracy comparable to Monte Carlo methods in only a fraction of the time. The method's implementation has been extended to 3D, and in this work, it is validated by comparison to DOSXYZnrc using a photon radiotherapy benchmark. The comparison demonstrates excellent agreement; of the voxels that received more than 10% of the maximum dose, over 97.3% pass a 2% / 2mm acceptance test and over 99.7% pass a 3% / 3mm test. Furthermore, the method is over an order of magnitude faster than DOSXYZnrc and is able to take advantage of both distributed-memory and shared-memory parallel architectures for increased performance.

  1. Charge transport in a-Si:H detectors: Comparison of analytical and Monte Carlo simulations

    International Nuclear Information System (INIS)

    To understand the signal formation in hydrogenated amorphous silicon (a-Si:H) p-i-n detectors, dispersive charge transport due to multiple trapping in a-Si:H tail states is studied both analytically and by Monte Carlo simulations. An analytical solution is found for the free electron and hole distributions n(x,t) and the transient current I(t) due to an initial electron-hole pair generated at an arbitrary depth in the detector for the case of exponential band tails and linear field profiles; integrating over all e-h pairs produced along the particle's trajectory yields the actual distributions and current; the induced charge Q(t) is obtained by numerically integrating the current. This generalizes previous models used to analyze time-of-flight experiments. The Monte Carlo simulation provides the same information but can be applied to arbitrary field profiles, field dependent mobilities and localized state distributions. A comparison of both calculations is made in a simple case to show that identical results are obtained over a large time domain. A comparison with measured signals confirms that the total induced charge depends on the applied bias voltage. The applicability of the same approach to other semiconductors is discussed

  2. Neutron Transmission through Sapphire Crystals

    DEFF Research Database (Denmark)

    Sapphire crystals are excellent filters of fast neutrons, while at the same time exhibit moderate to very little absorption at smaller energies. We have performed an extensive series of measurements in order to quantify the above effect. Alongside our experiments, we have performed a series...... of simulations, in order to reproduce the transmission of cold neutrons through sapphire crystals. Those simulations were part of the effort of validating and improving the newly developed interface between the Monte-Carlo neutron transport code MCNP and the Monte Carlo ray-tracing code McStas....

  3. Cooperative learning of neutron diffusion and transport theories

    International Nuclear Information System (INIS)

    A cooperative group instructional strategy is being used to teach a unit on neutron transport and diffusion theory in a first-year-graduate level, Reactor Theory course that was formerly presented in the traditional lecture/discussion style. Students are divided into groups of two or three for the duration of the unit. Class meetings are divided into traditional lecture/discussion segments punctuated by cooperative group exercises. The group exercises were designed to require the students to elaborate, summarize, or practice the material presented in the lecture/discussion segments. Both positive interdependence and individual accountability are fostered by adjusting individual grades on the unit exam by a factor dependent upon group achievement. Group collaboration was also encouraged on homework assignments by assigning each group a single grade on each assignment. The results of the unit exam have been above average in the two classes in which the cooperative group method was employed. In particular, the problem solving ability of the students has shown particular improvement. Further,the students felt that the cooperative group format was both more educationally effective and more enjoyable than the lecture/discussion format

  4. Neutron and photon transport calculations in fusion system. 2

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Satoshi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    1998-03-01

    On the application of MCNP to the neutron and {gamma}-ray transport calculations for fusion reactor system, the wide range design calculation has been carried out in the engineering design activities for the international thermonuclear fusion experimental reactor (ITER) being developed jointly by Japan, USA, EU and Russia. As the objects of shielding calculation for fusion reactors, there are the assessment of dose equivalent rate for living body shielding and the assessment of the nuclear response for the soundness of in-core structures. In the case that the detailed analysis of complicated three-dimensional shapes is required, the assessment using MCNP has been carried out. Also when the nuclear response of peripheral equipment due to the gap streaming between blanket modules is evaluated with good accuracy, the calculation with MCNP has been carried out. The analyses of the shieldings for blanket modules and NBI port are explained, and the examples of the results of analyses are shown. In the blanket modules, there are penetrating holes and continuous gap. In the case of the NBI port, shielding plug cannot be installed. These facts necessitate the MCNP analysis with high accuracy. (K.I.)

  5. Core-scale solute transport model selection using Monte Carlo analysis

    CERN Document Server

    Malama, Bwalya; James, Scott C

    2013-01-01

    Model applicability to core-scale solute transport is evaluated using breakthrough data from column experiments conducted with conservative tracers tritium (H-3) and sodium-22, and the retarding solute uranium-232. The three models considered are single-porosity, double-porosity with single-rate mobile-immobile mass-exchange, and the multirate model, which is a deterministic model that admits the statistics of a random mobile-immobile mass-exchange rate coefficient. The experiments were conducted on intact Culebra Dolomite core samples. Previously, data were analyzed using single- and double-porosity models although the Culebra Dolomite is known to possess multiple types and scales of porosity, and to exhibit multirate mobile-immobile-domain mass transfer characteristics at field scale. The data are reanalyzed here and null-space Monte Carlo analysis is used to facilitate objective model selection. Prediction (or residual) bias is adopted as a measure of the model structural error. The analysis clearly shows ...

  6. penORNL: a parallel Monte Carlo photon and electron transport package using PENELOPE

    Energy Technology Data Exchange (ETDEWEB)

    Bekar, Kursat B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Miller, Thomas Martin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Patton, Bruce W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Weber, Charles F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-01-01

    The parallel Monte Carlo photon and electron transport code package penORNL was developed at Oak Ridge National Laboratory to enable advanced scanning electron microscope (SEM) simulations on high performance computing systems. This paper discusses the implementations, capabilities and parallel performance of the new code package. penORNL uses PENELOPE for its physics calculations and provides all available PENELOPE features to the users, as well as some new features including source definitions specifically developed for SEM simulations, a pulse-height tally capability for detailed simulations of gamma and x-ray detectors, and a modified interaction forcing mechanism to enable accurate energy deposition calculations. The parallel performance of penORNL was extensively tested with several model problems, and very good linear parallel scaling was observed with up to 512 processors. penORNL, along with its new features, will be available for SEM simulations upon completion of the new pulse-height tally implementation.

  7. Monte Carlo simulation of phonon transport in variable cross-section nanowires

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    A dedicated Monte Carlo (MC) model is proposed to investigate the mechanism of phonon transport in variable cross-section silicon nanowires (NWs). Emphasis is placed on understanding the thermal rectification effect and thermal conduction in tapered cross-section and incremental cross-section NWs. In the simulations, both equal and unequal heat input conditions are discussed. Under the latter condition, the tapered cross-section NW has a more prominent thermal rectification effect. Additionally, the capacity of heat conduction in the tapered cross-section NW is always higher than that of the incremental one. Two reasons may be attributed to these behaviors: one is their different boundary conditions and the other is their different volume distribution. Although boundary scattering plays an important role in nanoscale structures, the results suggest the influence of boundary scattering on heat conduction is less obvious than that of volume distribution in NWs with variable cross-sections.

  8. Improved cache performance in Monte Carlo transport calculations using energy banding

    Science.gov (United States)

    Siegel, A.; Smith, K.; Felker, K.; Romano, P.; Forget, B.; Beckman, P.

    2014-04-01

    We present an energy banding algorithm for Monte Carlo (MC) neutral particle transport simulations which depend on large cross section lookup tables. In MC codes, read-only cross section data tables are accessed frequently, exhibit poor locality, and are typically too much large to fit in fast memory. Thus, performance is often limited by long latencies to RAM, or by off-node communication latencies when the data footprint is very large and must be decomposed on a distributed memory machine. The proposed energy banding algorithm allows maximal temporal reuse of data in band sizes that can flexibly accommodate different architectural features. The energy banding algorithm is general and has a number of benefits compared to the traditional approach. In the present analysis we explore its potential to achieve improvements in time-to-solution on modern cache-based architectures.

  9. MCPT: A Monte Carlo code for simulation of photon transport in tomographic scanners

    International Nuclear Information System (INIS)

    MCPT is a special-purpose Monte Carlo code designed to simulate photon transport in tomographic scanners. Variance reduction schemes and sampling games present in MCPT were selected to characterize features common to most tomographic scanners. Combined splitting and biasing (CSB) games are used to systematically sample important detection pathways. An efficient splitting game is used to tally particle energy deposition in detection zones. The pulse height distribution of each detector can be found by convolving the calculated energy deposition distribution with the detector's resolution function. A general geometric modelling package, HERMETOR, is used to describe the geometry of the tomographic scanners and provide MCPT information needed for particle tracking. MCPT's modelling capabilites are described and preliminary experimental validation is presented. (orig.)

  10. Monte Carlo Simulations of Spin Transport in Nanoscale InGaAs Field Effect Transistors

    CERN Document Server

    Thorpe, B; Langbein, F; Schirmer, S

    2016-01-01

    By augmenting an in-house developed, experimentally verified Monte Carlo device simulator with a Bloch equation model with a spin-orbit interaction Hamiltonian accounting for Dresselhaus and Rashba couplings, we simulate electron spin transport in a \\SI{25}{nm} gate length InGaAs MOSFET. We observe non-uniform decay of the net magnetization between the source and gate electrodes and an interesting magnetization recovery effect due to spin refocusing induced by high electric field between the gate and drain electrodes. We demonstrate coherent control of the polarization vector of the drain current via the source-drain and gate voltages, and show that the magnetization of the drain current is sensitive to strain in the channel, suggesting that the device could act as a room-temperature nanoscale strain sensor.

  11. Monte Carlo Simulations of Charge Transport in 2D Organic Photovoltaics.

    Science.gov (United States)

    Gagorik, Adam G; Mohin, Jacob W; Kowalewski, Tomasz; Hutchison, Geoffrey R

    2013-01-01

    The effect of morphology on charge transport in organic photovoltaics is assessed using Monte Carlo. In isotopic two-phase morphologies, increasing the domain size from 6.3 to 18.3 nm improves the fill factor by 11.6%, a result of decreased tortuosity and relaxation of Coulombic barriers. Additionally, when small aggregates of electron acceptors are interdispersed into the electron donor phase, charged defects form in the system, reducing fill factors by 23.3% on average, compared with systems without aggregates. In contrast, systems with idealized connectivity show a 3.31% decrease in fill factor when domain size was increased from 4 to 64 nm. We attribute this to a decreased rate of exciton separation at donor-acceptor interfaces. Finally, we notice that the presence of Coulomb interactions increases device performance as devices become smaller. The results suggest that for commonly found isotropic morphologies the Coulomb interactions between charge carriers dominates exciton separation effects.

  12. Analysis of Light Transport Features in Stone Fruits Using Monte Carlo Simulation.

    Directory of Open Access Journals (Sweden)

    Chizhu Ding

    Full Text Available The propagation of light in stone fruit tissue was modeled using the Monte Carlo (MC method. Peaches were used as the representative model of stone fruits. The effects of the fruit core and the skin on light transport features in the peaches were assessed. It is suggested that the skin, flesh and core should be separately considered with different parameters to accurately simulate light propagation in intact stone fruit. The detection efficiency was evaluated by the percentage of effective photons and the detection sensitivity of the flesh tissue. The fruit skin decreases the detection efficiency, especially in the region close to the incident point. The choices of the source-detector distance, detection angle and source intensity were discussed. Accurate MC simulations may result in better insight into light propagation in stone fruit and aid in achieving the optimal fruit quality inspection without extensive experimental measurements.

  13. Comparison of implicit and symbolic implicit Monte Carlo line transport with frequency weight vector extension

    Science.gov (United States)

    McKinley, Michael Scott; Brooks, Eugene D., III; Szoke, Abraham

    2003-07-01

    We compare the implicit Monte Carlo (IMC) technique to the symbolic IMC (SIMC) technique, with and without weight vectors in frequency space, for time-dependent line transport in the presence of collisional pumping. We examine the efficiency and accuracy of the IMC and SIMC methods for test problems involving the evolution of a collisionally pumped trapping problem to its steady-state, the surface heating of a cold medium by a beam, and the diffusion of energy from a localized region that is collisionally pumped. The importance of spatial biasing and teleportation for problems involving high opacity is demonstrated. Our numerical solution, along with its associated teleportation error, is checked against theoretical calculations for the last example.

  14. A Monte Carlo transport code study of the space radiation environment using FLUKA and ROOT

    CERN Document Server

    Wilson, T; Carminati, F; Brun, R; Ferrari, A; Sala, P; Empl, A; MacGibbon, J

    2001-01-01

    We report on the progress of a current study aimed at developing a state-of-the-art Monte-Carlo computer simulation of the space radiation environment using advanced computer software techniques recently available at CERN, the European Laboratory for Particle Physics in Geneva, Switzerland. By taking the next-generation computer software appearing at CERN and adapting it to known problems in the implementation of space exploration strategies, this research is identifying changes necessary to bring these two advanced technologies together. The radiation transport tool being developed is tailored to the problem of taking measured space radiation fluxes impinging on the geometry of any particular spacecraft or planetary habitat and simulating the evolution of that flux through an accurate model of the spacecraft material. The simulation uses the latest known results in low-energy and high-energy physics. The output is a prediction of the detailed nature of the radiation environment experienced in space as well a...

  15. ITS Version 6 : the integrated TIGER series of coupled electron/photon Monte Carlo transport codes.

    Energy Technology Data Exchange (ETDEWEB)

    Franke, Brian Claude; Kensek, Ronald Patrick; Laub, Thomas William

    2008-04-01

    ITS is a powerful and user-friendly software package permitting state-of-the-art Monte Carlo solution of lineartime-independent coupled electron/photon radiation transport problems, with or without the presence of macroscopic electric and magnetic fields of arbitrary spatial dependence. Our goal has been to simultaneously maximize operational simplicity and physical accuracy. Through a set of preprocessor directives, the user selects one of the many ITS codes. The ease with which the makefile system is applied combines with an input scheme based on order-independent descriptive keywords that makes maximum use of defaults and internal error checking to provide experimentalists and theorists alike with a method for the routine but rigorous solution of sophisticated radiation transport problems. Physical rigor is provided by employing accurate cross sections, sampling distributions, and physical models for describing the production and transport of the electron/photon cascade from 1.0 GeV down to 1.0 keV. The availability of source code permits the more sophisticated user to tailor the codes to specific applications and to extend the capabilities of the codes to more complex applications. Version 6, the latest version of ITS, contains (1) improvements to the ITS 5.0 codes, and (2) conversion to Fortran 90. The general user friendliness of the software has been enhanced through memory allocation to reduce the need for users to modify and recompile the code.

  16. Srna-Monte Carlo codes for proton transport simulation in combined and voxelized geometries

    CERN Document Server

    Ilic, R D; Stankovic, S J

    2002-01-01

    This paper describes new Monte Carlo codes for proton transport simulations in complex geometrical forms and in materials of different composition. The SRNA codes were developed for three dimensional (3D) dose distribution calculation in proton therapy and dosimetry. The model of these codes is based on the theory of proton multiple scattering and a simple model of compound nucleus decay. The developed package consists of two codes: SRNA-2KG and SRNA-VOX. The first code simulates proton transport in combined geometry that can be described by planes and second order surfaces. The second one uses the voxelized geometry of material zones and is specifically adopted for the application of patient computer tomography data. Transition probabilities for both codes are given by the SRNADAT program. In this paper, we will present the models and algorithms of our programs, as well as the results of the numerical experiments we have carried out applying them, along with the results of proton transport simulation obtaine...

  17. Comparison of Bonner sphere responses calculated by different Monte Carlo codes at energies between 1 MeV and 1 GeV – Potential impact on neutron dosimetry at energies higher than 20 MeV

    CERN Document Server

    Rühm, W; Pioch, C; Agosteo, S; Endo, A; Ferrarini, M; Rakhno, I; Rollet, S; Satoh, D; Vincke, H

    2014-01-01

    Bonner Spheres Spectrometry in its high-energy extended version is an established method to quantify neutrons at a wide energy range from several meV up to more than 1 GeV. In order to allow for quantitative measurements, the responses of the various spheres used in a Bonner Sphere Spectrometer (BSS) are usually simulated by Monte Carlo (MC) codes over the neutron energy range of interest. Because above 20 MeV experimental cross section data are scarce, intra-nuclear cascade (INC) and evaporation models are applied in these MC codes. It was suspected that this lack of data above 20 MeV may translate to differences in simulated BSS response functions depending on the MC code and nuclear models used, which in turn may add to the uncertainty involved in Bonner Sphere Spectrometry, in particular for neutron energies above 20 MeV. In order to investigate this issue in a systematic way, EURADOS (European Radiation Dosimetry Group) initiated an exercise where six groups having experience in neutron transport calcula...

  18. Neutron production and time resolution of a new class moderator for pulsed neutron diffraction. Measurements and transport calculations

    International Nuclear Information System (INIS)

    Measurements of neutron pulse time-width and intensity have been carried out on grids of small moderators placed side by side and decoupled by cadmium strips; a moderator concept introduced by the authors through previous publications. Transport calculations are based on the standard reactor code DOT 3.5 with the ENDF-B IV nuclear data library. (orig.)

  19. Modeling parameterized geometry in GPU-based Monte Carlo particle transport simulation for radiotherapy.

    Science.gov (United States)

    Chi, Yujie; Tian, Zhen; Jia, Xun

    2016-08-01

    Monte Carlo (MC) particle transport simulation on a graphics-processing unit (GPU) platform has been extensively studied recently due to the efficiency advantage achieved via massive parallelization. Almost all of the existing GPU-based MC packages were developed for voxelized geometry. This limited application scope of these packages. The purpose of this paper is to develop a module to model parametric geometry and integrate it in GPU-based MC simulations. In our module, each continuous region was defined by its bounding surfaces that were parameterized by quadratic functions. Particle navigation functions in this geometry were developed. The module was incorporated to two previously developed GPU-based MC packages and was tested in two example problems: (1) low energy photon transport simulation in a brachytherapy case with a shielded cylinder applicator and (2) MeV coupled photon/electron transport simulation in a phantom containing several inserts of different shapes. In both cases, the calculated dose distributions agreed well with those calculated in the corresponding voxelized geometry. The averaged dose differences were 1.03% and 0.29%, respectively. We also used the developed package to perform simulations of a Varian VS 2000 brachytherapy source and generated a phase-space file. The computation time under the parameterized geometry depended on the memory location storing the geometry data. When the data was stored in GPU's shared memory, the highest computational speed was achieved. Incorporation of parameterized geometry yielded a computation time that was ~3 times of that in the corresponding voxelized geometry. We also developed a strategy to use an auxiliary index array to reduce frequency of geometry calculations and hence improve efficiency. With this strategy, the computational time ranged in 1.75-2.03 times of the voxelized geometry for coupled photon/electron transport depending on the voxel dimension of the auxiliary index array, and in 0

  20. Modeling parameterized geometry in GPU-based Monte Carlo particle transport simulation for radiotherapy

    Science.gov (United States)

    Chi, Yujie; Tian, Zhen; Jia, Xun

    2016-08-01

    Monte Carlo (MC) particle transport simulation on a graphics-processing unit (GPU) platform has been extensively studied recently due to the efficiency advantage achieved via massive parallelization. Almost all of the existing GPU-based MC packages were developed for voxelized geometry. This limited application scope of these packages. The purpose of this paper is to develop a module to model parametric geometry and integrate it in GPU-based MC simulations. In our module, each continuous region was defined by its bounding surfaces that were parameterized by quadratic functions. Particle navigation functions in this geometry were developed. The module was incorporated to two previously developed GPU-based MC packages and was tested in two example problems: (1) low energy photon transport simulation in a brachytherapy case with a shielded cylinder applicator and (2) MeV coupled photon/electron transport simulation in a phantom containing several inserts of different shapes. In both cases, the calculated dose distributions agreed well with those calculated in the corresponding voxelized geometry. The averaged dose differences were 1.03% and 0.29%, respectively. We also used the developed package to perform simulations of a Varian VS 2000 brachytherapy source and generated a phase-space file. The computation time under the parameterized geometry depended on the memory location storing the geometry data. When the data was stored in GPU’s shared memory, the highest computational speed was achieved. Incorporation of parameterized geometry yielded a computation time that was ~3 times of that in the corresponding voxelized geometry. We also developed a strategy to use an auxiliary index array to reduce frequency of geometry calculations and hence improve efficiency. With this strategy, the computational time ranged in 1.75–2.03 times of the voxelized geometry for coupled photon/electron transport depending on the voxel dimension of the auxiliary index array, and in 0

  1. Modeling parameterized geometry in GPU-based Monte Carlo particle transport simulation for radiotherapy.

    Science.gov (United States)

    Chi, Yujie; Tian, Zhen; Jia, Xun

    2016-08-01

    Monte Carlo (MC) particle transport simulation on a graphics-processing unit (GPU) platform has been extensively studied recently due to the efficiency advantage achieved via massive parallelization. Almost all of the existing GPU-based MC packages were developed for voxelized geometry. This limited application scope of these packages. The purpose of this paper is to develop a module to model parametric geometry and integrate it in GPU-based MC simulations. In our module, each continuous region was defined by its bounding surfaces that were parameterized by quadratic functions. Particle navigation functions in this geometry were developed. The module was incorporated to two previously developed GPU-based MC packages and was tested in two example problems: (1) low energy photon transport simulation in a brachytherapy case with a shielded cylinder applicator and (2) MeV coupled photon/electron transport simulation in a phantom containing several inserts of different shapes. In both cases, the calculated dose distributions agreed well with those calculated in the corresponding voxelized geometry. The averaged dose differences were 1.03% and 0.29%, respectively. We also used the developed package to perform simulations of a Varian VS 2000 brachytherapy source and generated a phase-space file. The computation time under the parameterized geometry depended on the memory location storing the geometry data. When the data was stored in GPU's shared memory, the highest computational speed was achieved. Incorporation of parameterized geometry yielded a computation time that was ~3 times of that in the corresponding voxelized geometry. We also developed a strategy to use an auxiliary index array to reduce frequency of geometry calculations and hence improve efficiency. With this strategy, the computational time ranged in 1.75-2.03 times of the voxelized geometry for coupled photon/electron transport depending on the voxel dimension of the auxiliary index array, and in 0

  2. PHISICS multi-group transport neutronic capabilities for RELAP5

    Energy Technology Data Exchange (ETDEWEB)

    Epiney, A.; Rabiti, C.; Alfonsi, A.; Wang, Y.; Cogliati, J.; Strydom, G. [Idaho National Laboratory (INL), 2525 N. Fremont Ave., Idaho Falls, ID 83402 (United States)

    2012-07-01

    PHISICS is a neutronic code system currently under development at INL. Its goal is to provide state of the art simulation capability to reactor designers. This paper reports on the effort of coupling this package to the thermal hydraulic system code RELAP5. This will enable full prismatic core and system modeling and the possibility to model coupled (thermal-hydraulics and neutronics) problems with more options for 3D neutron kinetics, compared to the existing diffusion theory neutron kinetics module in RELAP5 (NESTLE). The paper describes the capabilities of the coupling and illustrates them with a set of sample problems. (authors)

  3. Transport calculation of thermal and cold neutrons using NMTC/JAERI-MCNP4A code system

    Energy Technology Data Exchange (ETDEWEB)

    Iga, Kiminori [Kyushu Univ., Fukuoka (Japan); Takada, Hiroshi; Nagao, Tadashi

    1998-01-01

    In order to investigate the applicability of the NMTC/JAERI-MCNP4A code system to the neutronics design study in the neutron science research project of JAERI, transport calculations of thermal and cold neutrons are performed with the code system on a spallation neutron source composed of light water cooled tantalum target with a moderator and a reflector system. The following neutronic characteristics are studied in the calculation : the variation of the intensity of neutrons emitted from a light water moderator or a liquid hydrogen with/without the B{sub 4}C decoupler, which are installed to produce sharp pulse, and that dependent on the position of external source neutrons in the tantalum target. The calculated neutron energy spectra are reproduced well by the semi-empirical formula with the parameter values reliable in physical meanings. It is found to be necessary to employ proper importance sampling technique in the statistics. It is confirmed from this work that the NMTC/JAERI-MCNP4A code system is applicable to the neutronics design study of spallation neutron sources proposed for the neutron science research project. (author)

  4. Monte Carlo simulation in the reaction rate's calculation with neutron-activation method

    International Nuclear Information System (INIS)

    With MCNP/4B code, the influence of cut-off energy, flux tallies, nuclear databases and perturbation on the reaction rate's calculation with neutron-activation method are analysed. When the effective reaction threshold is chosen as the cut-off energy, calculation time is considerably reduced and yet the results are not changed. Comparing calculations with cell tallies (F4) with those performed with detector tallies (F5), the counting efficiency of cell tallies is higher and the results are slightly higher, but still credible. With different nuclear databases, calculated results can be different. The perturbation among the detectors doesn't effect on the calculated results. (authors)

  5. The coupling of the neutron transport application RATTLESNAKE to the nuclear fuels performance application BISON under the MOOSE framework

    International Nuclear Information System (INIS)

    The MOOSE based reactor physics tool MAMMOTH provides the capability to seamlessly couple the neutron transport application RATTLESNAKE to the fuels performance application BISON to produce a higher fidelity tool for fuel performance simulations. The ultimate purpose of this coupling is to provide a tool with the predictive capabilities to gain new knowledge and help resolve fundamental questions in the fuel performance arena, i.e. high-burnup structures, pellet-cladding interaction, missing pellet surface, etc. RATTLESNAKE solves the self-adjoint angular flux transport equation, derived from the linearized Boltzmann transport equation, and provides a sub-pin level resolution of the multigroup neutron flux. BISON solves the coupled thermomechanical equations for the fuel on a sub-millimeter scale. The coupling within the MOOSE framework allows both applications to solve their respective systems on aligned and unaligned unstructured finite element meshes. MAMMOTH uses the power density calculated by RATTLESNAKE to compute the local burnup evolution. Subsequently, MAMMOTH transfers the power density and burnup distribution to BISON with the MOOSE Multiapp transfer system. BISON in turn is able to provide sub-pin level temperature for cross section feed back effects. Multiple depletion cases were run with one-way and two-way data transfer in MAMMOTH for RATTLESNAKE-BISON. The one-way eigenvalues obtained show good agreement with the reference values obtained from the lattice physics code DRAGON4 while the two-way eigenvalue show expected differences. The power distributions obtained are consistent with both DRAGON4 and the SERPENT Monte Carlo code. The one-way and two-way calculations produce power density results that are comparable with those of the internal, static, Lassmannstyle model in BISON. Differences in the power densities arise from the use of better neutron energy deposition parameters obtained from the DRAGON4 tabulations, and differences in the fuel

  6. Monte Carlo neutron fluence calculations, activation measurements and spectrum adjustment for the KORPUS dosimetry experiment

    International Nuclear Information System (INIS)

    KORPUS is an irradiation facility located at the lateral core surface of the 6 MW experimental reactor RBT-6 in Dimitrovgrad. In this work the KORPUS irradiation experiment has been used to demonstrate the capability of the pressure vessel dosimetry methodology developed in Rossendorf to solve these problems. At the same time the experiments were used to test recent improvements of this methodology including a new procedure for treatment of elastic scattering in the Monte Carlo code TRAMO and a new multispectrum version of the adjustment code. By means of a series of calculations the influence of model and data approximations were investigated aiming at an evaluation of the uncertainties of the calculations. Further, uncertainty investigations were carried out in connection with spectrum adjustment resulting in covariances of spectra, measured reaction rates and fluence integrals. (orig.)

  7. Monte Carlo Studies of two Different Conversion Layers for Neutron Measurements with Medipix Silicon Detector.

    CERN Document Server

    Larsen, Andreas

    2013-01-01

    In 2007 the ventilation system of CNGS failed and investigations showed that the failure was due to Single Event Upset (SEU). Since then there has been increased interest in studies of neutron flux, that can potentially cause SEU. Two Medipix detectors have previously been installed in the CMS cavern on a test basis and have shown to work as intended[1]. More Medipix detectors will be installed to provide high resolution measurements of the particle flux in the vicinity of the CMS, focusing on measurements of the neutron flux. The measurements will provide an important basis to know what precautions to take to avoid another failure due to SEU. The measurements will also constitute a valuably reference to the FLUKA simulations of the general flux in the CMS cavern, that can potentially lead to important corrections of the simulations. Furthermore, measurements from the Medipix detectors will act as a cross check on the hadronic forward detector radiation monitoring system (HF radmon). Bonnos spheres are alread...

  8. Development and application of neutron transport methods and uncertainty analyses for reactor core calculations. Technical report; Entwicklung und Einsatz von Neutronentransportmethoden und Unsicherheitsanalysen fuer Reaktorkernberechnungen. Technischer Bericht

    Energy Technology Data Exchange (ETDEWEB)

    Zwermann, W.; Aures, A.; Bernnat, W.; and others

    2013-06-15

    This report documents the status of the research and development goals reached within the reactor safety research project RS1503 ''Development and Application of Neutron Transport Methods and Uncertainty Analyses for Reactor Core Calculations'' as of the 1{sup st} quarter of 2013. The superordinate goal of the project is the development, validation, and application of neutron transport methods and uncertainty analyses for reactor core calculations. These calculation methods will mainly be applied to problems related to the core behaviour of light water reactors and innovative reactor concepts. The contributions of this project towards achieving this goal are the further development, validation, and application of deterministic and stochastic calculation programmes and of methods for uncertainty and sensitivity analyses, as well as the assessment of artificial neutral networks, for providing a complete nuclear calculation chain. This comprises processing nuclear basis data, creating multi-group data for diffusion and transport codes, obtaining reference solutions for stationary states with Monte Carlo codes, performing coupled 3D full core analyses in diffusion approximation and with other deterministic and also Monte Carlo transport codes, and implementing uncertainty and sensitivity analyses with the aim of propagating uncertainties through the whole calculation chain from fuel assembly, spectral and depletion calculations to coupled transient analyses. This calculation chain shall be applicable to light water reactors and also to innovative reactor concepts, and therefore has to be extensively validated with the help of benchmarks and critical experiments.

  9. SU-E-T-558: Monte Carlo Photon Transport Simulations On GPU with Quadric Geometry

    International Nuclear Information System (INIS)

    Purpose: Monte Carlo simulation on GPU has experienced rapid advancements over the past a few years and tremendous accelerations have been achieved. Yet existing packages were developed only in voxelized geometry. In some applications, e.g. radioactive seed modeling, simulations in more complicated geometry are needed. This abstract reports our initial efforts towards developing a quadric geometry module aiming at expanding the application scope of GPU-based MC simulations. Methods: We defined the simulation geometry consisting of a number of homogeneous bodies, each specified by its material composition and limiting surfaces characterized by quadric functions. A tree data structure was utilized to define geometric relationship between different bodies. We modified our GPU-based photon MC transport package to incorporate this geometry. Specifically, geometry parameters were loaded into GPU’s shared memory for fast access. Geometry functions were rewritten to enable the identification of the body that contains the current particle location via a fast searching algorithm based on the tree data structure. Results: We tested our package in an example problem of HDR-brachytherapy dose calculation for shielded cylinder. The dose under the quadric geometry and that under the voxelized geometry agreed in 94.2% of total voxels within 20% isodose line based on a statistical t-test (95% confidence level), where the reference dose was defined to be the one at 0.5cm away from the cylinder surface. It took 243sec to transport 100million source photons under this quadric geometry on an NVidia Titan GPU card. Compared with simulation time of 99.6sec in the voxelized geometry, including quadric geometry reduced efficiency due to the complicated geometry-related computations. Conclusion: Our GPU-based MC package has been extended to support photon transport simulation in quadric geometry. Satisfactory accuracy was observed with a reduced efficiency. Developments for charged

  10. SU-E-T-558: Monte Carlo Photon Transport Simulations On GPU with Quadric Geometry

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Y; Tian, Z; Jiang, S; Jia, X [The University of Texas Southwestern Medical Ctr, Dallas, TX (United States)

    2015-06-15

    Purpose: Monte Carlo simulation on GPU has experienced rapid advancements over the past a few years and tremendous accelerations have been achieved. Yet existing packages were developed only in voxelized geometry. In some applications, e.g. radioactive seed modeling, simulations in more complicated geometry are needed. This abstract reports our initial efforts towards developing a quadric geometry module aiming at expanding the application scope of GPU-based MC simulations. Methods: We defined the simulation geometry consisting of a number of homogeneous bodies, each specified by its material composition and limiting surfaces characterized by quadric functions. A tree data structure was utilized to define geometric relationship between different bodies. We modified our GPU-based photon MC transport package to incorporate this geometry. Specifically, geometry parameters were loaded into GPU’s shared memory for fast access. Geometry functions were rewritten to enable the identification of the body that contains the current particle location via a fast searching algorithm based on the tree data structure. Results: We tested our package in an example problem of HDR-brachytherapy dose calculation for shielded cylinder. The dose under the quadric geometry and that under the voxelized geometry agreed in 94.2% of total voxels within 20% isodose line based on a statistical t-test (95% confidence level), where the reference dose was defined to be the one at 0.5cm away from the cylinder surface. It took 243sec to transport 100million source photons under this quadric geometry on an NVidia Titan GPU card. Compared with simulation time of 99.6sec in the voxelized geometry, including quadric geometry reduced efficiency due to the complicated geometry-related computations. Conclusion: Our GPU-based MC package has been extended to support photon transport simulation in quadric geometry. Satisfactory accuracy was observed with a reduced efficiency. Developments for charged

  11. Oxygen transport properties estimation by classical trajectory–direct simulation Monte Carlo

    Energy Technology Data Exchange (ETDEWEB)

    Bruno, Domenico, E-mail: domenico.bruno@cnr.it [Istituto di Metodologie Inorganiche e dei Plasmi, Consiglio Nazionale delle Ricerche– Via G. Amendola 122, 70125 Bari (Italy); Frezzotti, Aldo, E-mail: aldo.frezzotti@polimi.it; Ghiroldi, Gian Pietro, E-mail: gpghiro@gmail.com [Dipartimento di Scienze e Tecnologie Aerospaziali, Politecnico di Milano–Via La Masa 34, 20156 Milano (Italy)

    2015-05-15

    Coupling direct simulation Monte Carlo (DSMC) simulations with classical trajectory calculations is a powerful tool to improve predictive capabilities of computational dilute gas dynamics. The considerable increase in computational effort outlined in early applications of the method can be compensated by running simulations on massively parallel computers. In particular, Graphics Processing Unit acceleration has been found quite effective in reducing computing time of classical trajectory (CT)-DSMC simulations. The aim of the present work is to study dilute molecular oxygen flows by modeling binary collisions, in the rigid rotor approximation, through an accurate Potential Energy Surface (PES), obtained by molecular beams scattering. The PES accuracy is assessed by calculating molecular oxygen transport properties by different equilibrium and non-equilibrium CT-DSMC based simulations that provide close values of the transport properties. Comparisons with available experimental data are presented and discussed in the temperature range 300–900 K, where vibrational degrees of freedom are expected to play a limited (but not always negligible) role.

  12. Cosmic ray heliospheric transport study with neutron monitor data

    Science.gov (United States)

    Ahluwalia, H. S.; Ygbuhay, R. C.; Modzelewska, R.; Dorman, L. I.; Alania, M. V.

    2015-10-01

    Determining transport coefficients for galactic cosmic ray (GCR) propagation in the turbulent interplanetary magnetic field (IMF) poses a fundamental challenge in modeling cosmic ray modulation processes. GCR scattering in the solar wind involves wave-particle interaction, the waves being Alfven waves which propagate along the ambient field (B). Empirical values at 1 AU are determined for the components of the diffusion tensor for GCR propagation in the heliosphere using neutron monitor (NM) data. At high rigidities, particle density gradients and mean free paths at 1 AU in B can only be computed from the solar diurnal anisotropy (SDA) represented by a vector A (components Ar, Aϕ, and Aθ) in a heliospherical polar coordinate system. Long-term changes in SDA components of NMs (with long track record and the median rigidity of response Rm ~ 20 GV) are used to compute yearly values of the transport coefficients for 1963-2013. We confirm the previously reported result that the product of the parallel (to B) mean free path (λ||) and radial density gradient (Gr) computed from NM data exhibits a weak Schwabe cycle (11y) but strong Hale magnetic cycle (22y) dependence. Its value is most depressed in solar activity minima for positive (p) polarity intervals (solar magnetic field in the Northern Hemisphere points outward from the Sun) when GCRs drift from the polar regions toward the helioequatorial plane and out along the heliospheric current sheet (HCS), setting up a symmetric gradient Gθs pointing away from HCS. Gr drives all SDA components and λ|| Gr contributes to the diffusive component (Ad) of the ecliptic plane anisotropy (A). GCR transport is commonly discussed in terms of an isotropic hard sphere scattering (also known as billiard-ball scattering) in the solar wind plasma. We use it with a flat HCS model and the Ahluwalia-Dorman master equations to compute the coefficients α (=λ⊥/λ∥) and ωτ (a measure of turbulence in the solar wind) and transport

  13. STUDI PEMODELAN DAN PERHITUNGAN TRANSPORT MONTE CARLO DALAM TERAS HTR PEBBLE BED

    Directory of Open Access Journals (Sweden)

    Zuhair .

    2013-01-01

    Full Text Available Konsep sistem energi VHTR baik yang berbahan bakar pebble (VHTR pebble bed maupun blok prismatik (VHTR prismatik menarik perhatian fisikawan reaktor nuklir. Salah satu kelebihan teknologi bahan bakar bola adalah menawarkan terobosan teknologi pengisian bahan bakar tanpa harus menghentikan produksi listrik. Selain itu, partikel bahan bakar pebble dengan kernel uranium oksida (UO2 atau uranium oksikarbida (UCO yang dibalut TRISO dan pelapisan silikon karbida (SiC dianggap sebagai opsi utama dengan pertimbangan performa tinggi pada burn-up bahan bakar dan temperatur tinggi. Makalah ini mendiskusikan pemodelan dan perhitungan transport Monte Carlo dalam teras HTR pebble bed. HTR pebble bed adalah reaktor berpendingin gas temperatur tinggi dan bermoderator grafit dengan kemampuan kogenerasi. Perhitungan dikerjakan dengan program MCNP5 pada temperatur 1200 K. Pustaka data nuklir energi kontinu ENDF/B-V dan ENDF/B-VI dimanfaatkan untuk melengkapi analisis. Hasil perhitungan secara keseluruhan menunjukkan konsistensi dengan nilai keff yang hampir sama untuk pustaka data nuklir yang digunakan. Pustaka ENDF/B-VI (66c selalu memproduksi keff lebih besar dibandingkan ENDF/B-V (50c maupun ENDF/B-VI (60c dengan bias kurang dari 0,25%. Kisi BCC memprediksi keff hampir selalu lebih kecil daripada kisi lainnya, khususnya FCC. Nilai keff kisi BCC lebih dekat dengan kisi FCC dengan bias kurang dari 0,19% sedangkan dengan kisi SH bias perhitungannya kurang dari 0,22%. Fraksi packing yang sedikit berbeda (BCC= 61%, SH= 60,459% tidak membuat bias perhitungan menjadi berbeda jauh. Estimasi keff ketiga model kisi menyimpulkan bahwa model BCC lebih bisa diadopsi dalam perhitungan HTR pebble bed dibandingkan model FCC dan SH. Verifikasi hasil estimasi ini perlu dilakukan dengan simulasi Monte Carlo atau bahkan program deterministik lainnya guna optimisasi perhitungan teras reaktor temperatur tinggi.   Kata-kunci: kernel, TRISO, bahan bakar pebble, HTR pebble bed

  14. Neutron interaction and their transport with bulk materials

    Energy Technology Data Exchange (ETDEWEB)

    Rani, Esther Kalpana, E-mail: esther.kalpanarani@gmail.com [Department of Physics JNT University, Nachupally, Karimnagar, Telangana, 500055 (India); Radhika, K., E-mail: radhikanit@gmail.com [Department of Humanities and Applied Sciences, Talla Padmavathi College of Engineering, Warangal, Telangana, 506004 (India)

    2015-05-15

    In the current paper an attempt was made to study and provide fundamental information about neutron interactions that are important to nuclear material measurements. The application of this study is explained about macroscopic interactions with bulk compound materials through a program in DEV C++ language which is done by enabling interaction of neutrons in nature. The output of the entire process depends upon the random number (i.e., incident neutron number), thickness of the material and mean free path as input parameters. Further the current study emphasizes on the usage of materials in shielding.

  15. The structure of calcium metaphosphate glass obtained from x-ray and neutron diffraction and reverse Monte Carlo modelling

    International Nuclear Information System (INIS)

    The short range structure of (CaO)0.5(P2O5)0.5 glass has been studied using x-ray and neutron diffraction and modelled using the reverse Monte Carlo method. Using this combination of techniques has allowed six interatomic correlations to be distinguished and fitted to obtain a set of bond lengths and coordination numbers that describe the structure of the glass. The glass consists of metaphosphate chains of phosphate tetrahedra and each phosphate unit has two non-bridging oxygen atoms available for coordination with Ca. The Ca-O correlation was fitted with two peaks at 2.35 and 2.86 A, representing a broad distribution of bond lengths. The total Ca-O coordination is 6.9 and is consistent with distorted polyhedral units such as capped octahedra or capped trigonal prisms. It is found that most non-bridging oxygen atoms are bonded to two calcium atoms. All of these observations are consistent with Hoppe's model for phosphate glasses. Furthermore, the medium range order is revealed to consist of phosphate chains intertwined with apparently elongated clusters of Ca ions, and the Ca-O and Ca-P correlations contributed significantly to the first sharp diffraction peak in x-ray diffraction.

  16. A GPU-based Monte Carlo dose calculation code for photon transport in a voxel phantom

    International Nuclear Information System (INIS)

    As the most accurate method to estimate absorbed dose in radiotherapy, Monte Carlo method has been widely used in radiotherapy treatment planning. Nevertheless, its efficiency can be improved for clinical routine applications. In this paper, we present the CUBMC code, a GPU-based Mc photon transport algorithm for dose calculation under the Compute Unified Device Architecture platform. The simulation of physical events is based on the algorithm used in Penelope, and the cross section table used is the one generated by the Material routine, als present in Penelope code. Photons are transported in voxel-based geometries with different compositions. To demonstrate the capabilities of the algorithm developed in the present work four 128 x 128 x 128 voxel phantoms have been considered. One of them is composed by a homogeneous water-based media, the second is composed by bone, the third is composed by lung and the fourth is composed by a heterogeneous bone and vacuum geometry. Simulations were done considering a 6 MeV monoenergetic photon point source. There are two distinct approaches that were used for transport simulation. The first of them forces the photon to stop at every voxel frontier, the second one is the Woodcock method, where the photon stop in the frontier will be considered depending on the material changing across the photon travel line. Dose calculations using these methods are compared for validation with Penelope and MCNP5 codes. Speed-up factors are compared using a NVidia GTX 560-Ti GPU card against a 2.27 GHz Intel Xeon CPU processor. (Author)

  17. A GPU-based Monte Carlo dose calculation code for photon transport in a voxel phantom

    Energy Technology Data Exchange (ETDEWEB)

    Bellezzo, M.; Do Nascimento, E.; Yoriyaz, H., E-mail: mbellezzo@gmail.br [Instituto de Pesquisas Energeticas e Nucleares / CNEN, Av. Lineu Prestes 2242, Cidade Universitaria, 05508-000 Sao Paulo (Brazil)

    2014-08-15

    As the most accurate method to estimate absorbed dose in radiotherapy, Monte Carlo method has been widely used in radiotherapy treatment planning. Nevertheless, its efficiency can be improved for clinical routine applications. In this paper, we present the CUBMC code, a GPU-based Mc photon transport algorithm for dose calculation under the Compute Unified Device Architecture platform. The simulation of physical events is based on the algorithm used in Penelope, and the cross section table used is the one generated by the Material routine, als present in Penelope code. Photons are transported in voxel-based geometries with different compositions. To demonstrate the capabilities of the algorithm developed in the present work four 128 x 128 x 128 voxel phantoms have been considered. One of them is composed by a homogeneous water-based media, the second is composed by bone, the third is composed by lung and the fourth is composed by a heterogeneous bone and vacuum geometry. Simulations were done considering a 6 MeV monoenergetic photon point source. There are two distinct approaches that were used for transport simulation. The first of them forces the photon to stop at every voxel frontier, the second one is the Woodcock method, where the photon stop in the frontier will be considered depending on the material changing across the photon travel line. Dose calculations using these methods are compared for validation with Penelope and MCNP5 codes. Speed-up factors are compared using a NVidia GTX 560-Ti GPU card against a 2.27 GHz Intel Xeon CPU processor. (Author)

  18. Spin diffusive modes and thermal transport in neutron star crusts

    CERN Document Server

    Sedrakian, Armen

    2015-01-01

    In this contribution we first review a method for obtaining the collective modes of pair-correlated neutron matter as found in a neutron star inner crust. We discuss two classes of modes corresponding to density and spin perturbations with energy spectra $\\omega = \\omega_0 + \\alpha q^2$, where $\\omega_0 = 2\\Delta$ is the threshold frequency and $\\Delta$ is the gap in the neutron fluid spectrum. For characteristic values of Landau parameters in neutron star crusts the exitonic density modes have $\\alpha 0$ and they exist above $\\omega_0$ which implies that these modes are damped. As an application of these findings we compute the thermal conductivity due to spin diffusive modes and show that it scales as $T^{1/2} \\exp(-2\\omega_0/T)$ in the case where their two-by-two scattering cross-section is weakly dependent on temperature.

  19. Neutron shielding calculations in a proton therapy facility based on Monte Carlo simulations and analytical models: Criterion for selecting the method of choice

    International Nuclear Information System (INIS)

    Proton therapy facilities are shielded to limit the amount of secondary radiation to which patients, occupational workers and members of the general public are exposed. The most commonly applied shielding design methods for proton therapy facilities comprise semi-empirical and analytical methods to estimate the neutron dose equivalent. This study compares the results of these methods with a detailed simulation of a proton therapy facility by using the Monte Carlo technique. A comparison of neutron dose equivalent values predicted by the various methods reveals the superior accuracy of the Monte Carlo predictions in locations where the calculations converge. However, the reliability of the overall shielding design increases if simulation results, for which solutions have not converged, e.g. owing to too few particle histories, can be excluded, and deterministic models are being used at these locations. Criteria to accept or reject Monte Carlo calculations in such complex structures are not well understood. An optimum rejection criterion would allow all converging solutions of Monte Carlo simulation to be taken into account, and reject all solutions with uncertainties larger than the design safety margins. In this study, the optimum rejection criterion of 10% was found. The mean ratio was 26, 62% of all receptor locations showed a ratio between 0.9 and 10, and 92% were between 1 and 100. (authors)

  20. Parallel Monte Carlo transport modeling in the context of a time-dependent, three-dimensional multi-physics code

    Energy Technology Data Exchange (ETDEWEB)

    Procassini, R.J. [Lawrence Livermore National lab., CA (United States)

    1997-12-31

    The fine-scale, multi-space resolution that is envisioned for accurate simulations of complex weapons systems in three spatial dimensions implies flop-rate and memory-storage requirements that will only be obtained in the near future through the use of parallel computational techniques. Since the Monte Carlo transport models in these simulations usually stress both of these computational resources, they are prime candidates for parallelization. The MONACO Monte Carlo transport package, which is currently under development at LLNL, will utilize two types of parallelism within the context of a multi-physics design code: decomposition of the spatial domain across processors (spatial parallelism) and distribution of particles in a given spatial subdomain across additional processors (particle parallelism). This implementation of the package will utilize explicit data communication between domains (message passing). Such a parallel implementation of a Monte Carlo transport model will result in non-deterministic communication patterns. The communication of particles between subdomains during a Monte Carlo time step may require a significant level of effort to achieve a high parallel efficiency.

  1. Spectrometry and emission tomographic image reconstruction stimulated by neutrons via EM algorithm and Monte Carlo Method

    International Nuclear Information System (INIS)

    The NSECT (Neutron Stimulated Emission Computed Tomography) figures as a new spectrographic technique able to evaluate in vivo the concentration of elements using the inelastic scattering reaction (n,n'). Since its introduction, several improvements have been proposed with the aim of investigating applications for clinical diagnosis and reduction of absorbed dose associated with CT acquisition. In this context, two new diagnostic applications are presented using spectroscopic and tomographic approaches from NSECT. A new methodology has also been proposed to optimize the sinogram sampling that is directly related to the quality of the reconstruction by the irradiation protocol. The studies were developed based on simulations with MCNP5 code. Diagnosis of Renal Cell Carcinoma (RCC) and the detection of breast microcalcifications were evaluated in studies conducted using a human phantom. The obtained results demonstrate the ability of the NSECT technique to detect changes in the composition of the modeled tissues as a function of the development of evaluated pathologies. The proposed method for optimizing sinograms was able to analytically simulate the composition of the irradiated medium allowing the assessment of quality of reconstruction and effective dose in terms of the sampling rate. However, future research must be conducted to quantify the sensitivity of detection according to the selected elements. (author)

  2. Discrete ordinates method for three-dimensional neutron transport equation based on unstructured-meshes

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A discrete ordinates method for a threedimensional first-order neutron transport equation based on unstructured-meshes that avoids the singularity of the second-order neutron transport equation in void regions was derived.The finite element variation equation was obtained using the least-squares method.A three-dimensional transport calculation code was developed.Both the triangular-z and the tetrahedron elements were included.The numerical results of some benchmark problems demonstrated that this method can solve neutron transport problems in unstructuredmeshes very well.For most problems,the error of the eigenvalue and the angular flux is less than 0.3% and 3.0% respectively.

  3. SU-E-T-591: Measurement and Monte Carlo Simulation of Stray Neutrons in Passive Scattering Proton Therapy: Needs and Challenges

    Energy Technology Data Exchange (ETDEWEB)

    Farah, J; Bonfrate, A; Donadille, L; Dubourg, N; Lacoste, V; Martinetti, F; Sayah, R; Trompier, F; Clairand, I [IRSN - Institute for Radiological Protection and Nuclear Safety, Fontenay-aux-roses (France); Caresana, M [Politecnico di Milano, Milano (Italy); Delacroix, S; Nauraye, C [Institut Curie - Centre de Protontherapie d Orsay, Orsay (France); Herault, J [Centre Antoine Lacassagne, Nice (France); Piau, S; Vabre, I [Institut de Physique Nucleaire d Orsay, Orsay (France)

    2014-06-01

    Purpose: Measure stray radiation inside a passive scattering proton therapy facility, compare values to Monte Carlo (MC) simulations and identify the actual needs and challenges. Methods: Measurements and MC simulations were considered to acknowledge neutron exposure associated with 75 MeV ocular or 180 MeV intracranial passively scattered proton treatments. First, using a specifically-designed high sensitivity Bonner Sphere system, neutron spectra were measured at different positions inside the treatment rooms. Next, measurement-based mapping of neutron ambient dose equivalent was fulfilled using several TEPCs and rem-meters. Finally, photon and neutron organ doses were measured using TLDs, RPLs and PADCs set inside anthropomorphic phantoms (Rando, 1 and 5-years-old CIRS). All measurements were also simulated with MCNPX to investigate the efficiency of MC models in predicting stray neutrons considering different nuclear cross sections and models. Results: Knowledge of the neutron fluence and energy distribution inside a proton therapy room is critical for stray radiation dosimetry. However, as spectrometry unfolding is initiated using a MC guess spectrum and suffers from algorithmic limits a 20% spectrometry uncertainty is expected. H*(10) mapping with TEPCs and rem-meters showed a good agreement between the detectors. Differences within measurement uncertainty (10–15%) were observed and are inherent to the energy, fluence and directional response of each detector. For a typical ocular and intracranial treatment respectively, neutron doses outside the clinical target volume of 0.4 and 11 mGy were measured inside the Rando phantom. Photon doses were 2–10 times lower depending on organs position. High uncertainties (40%) are inherent to TLDs and PADCs measurements due to the need for neutron spectra at detector position. Finally, stray neutrons prediction with MC simulations proved to be extremely dependent on proton beam energy and the used nuclear models and

  4. Physics models and nuclear data evaluations for enhanced Monte Carlo transport

    International Nuclear Information System (INIS)

    We describe recent evaluations of neutron and proton interaction cross sections up to 150 MeV in the LA150 Data Library, for use in MCNPX computer code simulations of accelerator-driven systems (ADS). An overview is provided of the nuclear theory used. A number of benchmark comparisons against experiments are described, for thin and thick-target neutron production, neutron transmission through macroscopic slabs, and neutron heating and damage. Future data needs for waste transmutation are also briefly described. (orig.)

  5. The Wigner Monte-Carlo method for nanoelectronic devices a particle description of quantum transport and decoherence

    CERN Document Server

    Querlioz, Damien

    2013-01-01

    This book gives an overview of the quantum transport approaches for nanodevices and focuses on the Wigner formalism. It details the implementation of a particle-based Monte Carlo solution of the Wigner transport equation and how the technique is applied to typical devices exhibiting quantum phenomena, such as the resonant tunnelling diode, the ultra-short silicon MOSFET and the carbon nanotube transistor. In the final part, decoherence theory is used to explain the emergence of the semi-classical transport in nanodevices.

  6. Development of a GPU-based Monte Carlo dose calculation code for coupled electron-photon transport

    CERN Document Server

    Jia, Xun; Sempau, Josep; Choi, Dongju; Majumdar, Amitava; Jiang, Steve B

    2009-01-01

    Monte Carlo simulation is the most accurate method for absorbed dose calculations in radiotherapy. Its efficiency still requires improvement for routine clinical applications, especially for online adaptive radiotherapy. In this paper, we report our recent development on a GPU-based Monte Carlo dose calculation code for coupled electron-photon transport. We have implemented the Dose Planning Method (DPM) Monte Carlo dose calculation package (Sempau et al, Phys. Med. Biol., 45(2000)2263-2291) on GPU architecture under CUDA platform. The implementation has been tested with respect to the original sequential DPM code on CPU in two cases. Our results demonstrate the adequate accuracy of the GPU implementation for both electron and photon beams in radiotherapy energy range. A speed up factor of 4.5 and 5.5 times have been observed for electron and photon testing cases, respectively, using an NVIDIA Tesla C1060 GPU card against a 2.27GHz Intel Xeon CPU processor .

  7. Comparison of some popular Monte Carlo solution for proton transportation within pCT problem

    Energy Technology Data Exchange (ETDEWEB)

    Evseev, Ivan; Assis, Joaquim T. de; Yevseyeva, Olga [Universidade do Estado do Rio de Janeiro (UERJ), Nova Friburgo, RJ (Brazil). Inst. Politecnico], E-mail: evseev@iprj.uerj.br, E-mail: joaquim@iprj.uerj.br, E-mail: yevseyeva@iprj.uerj.br; Lopes, Ricardo T.; Cardoso, Jose J.B.; Silva, Ademir X. da [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Lab. de Instrumentacao Nuclear], E-mail: ricardo@lin.ufrj.br, E-mail: jjbrum@oi.com.br, E-mail: ademir@con.ufrj.br; Vinagre Filho, Ubirajara M. [Instituto de Engenharia Nuclear IEN/CNEN-RJ, Rio de Janeiro, RJ (Brazil)], E-mail: bira@ien.gov.br; Hormaza, Joel M. [UNESP, Botucatu, SP (Brazil). Inst. de Biociencias], E-mail: jmesa@ibb.unesp.br; Schelin, Hugo R.; Paschuk, Sergei A.; Setti, Joao A.P.; Milhoretto, Edney [Universidade Tecnologica Federal do Parana, Curitiba, PR (Brazil)], E-mail: schelin@cpgei.cefetpr.br, E-mail: sergei@utfpr.edu.br, E-mail: jsetti@gmail.com, E-mail: edneymilhoretto@yahoo.com

    2007-07-01

    The proton transport in matter is described by the Boltzmann kinetic equation for the proton flux density. This equation, however, does not have a general analytical solution. Some approximate analytical solutions have been developed within a number of significant simplifications. Alternatively, the Monte Carlo simulations are widely used. Current work is devoted to the discussion of the proton energy spectra obtained by simulation with SRIM2006, GEANT4 and MCNPX packages. The simulations have been performed considering some further applications of the obtained results in computed tomography with proton beam (pCT). Thus the initial and outgoing proton energies (3 / 300 MeV) as well as the thickness of irradiated target (water and aluminum phantoms within 90% of the full range for a given proton beam energy) were considered in the interval of values typical for pCT applications. One from the most interesting results of this comparison is that while the MCNPX spectra are in a good agreement with analytical description within Fokker-Plank approximation and the GEANT4 simulated spectra are slightly shifted from them the SRIM2006 simulations predict a notably higher mean energy loss for protons. (author)

  8. Core-scale solute transport model selection using Monte Carlo analysis

    Science.gov (United States)

    Malama, Bwalya; Kuhlman, Kristopher L.; James, Scott C.

    2013-06-01

    Model applicability to core-scale solute transport is evaluated using breakthrough data from column experiments conducted with conservative tracers tritium (3H) and sodium-22 (22Na ), and the retarding solute uranium-232 (232U). The three models considered are single-porosity, double-porosity with single-rate mobile-immobile mass-exchange, and the multirate model, which is a deterministic model that admits the statistics of a random mobile-immobile mass-exchange rate coefficient. The experiments were conducted on intact Culebra Dolomite core samples. Previously, data were analyzed using single-porosity and double-porosity models although the Culebra Dolomite is known to possess multiple types and scales of porosity, and to exhibit multirate mobile-immobile-domain mass transfer characteristics at field scale. The data are reanalyzed here and null-space Monte Carlo analysis is used to facilitate objective model selection. Prediction (or residual) bias is adopted as a measure of the model structural error. The analysis clearly shows single-porosity and double-porosity models are structurally deficient, yielding late-time residual bias that grows with time. On the other hand, the multirate model yields unbiased predictions consistent with the late-time -5/2 slope diagnostic of multirate mass transfer. The analysis indicates the multirate model is better suited to describing core-scale solute breakthrough in the Culebra Dolomite than the other two models.

  9. Monte Carlo model of neutral-particle transport in diverted plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Heifetz, D.; Post, D.; Petravic, M.; Weisheit, J.; Bateman, G.

    1981-11-01

    The transport of neutral atoms and molecules in the edge and divertor regions of fusion experiments has been calculated using Monte-Carlo techniques. The deuterium, tritium, and helium atoms are produced by recombination in the plasma and at the walls. The relevant collision processes of charge exchange, ionization, and dissociation between the neutrals and the flowing plasma electrons and ions are included, along with wall reflection models. General two-dimensional wall and plasma geometries are treated in a flexible manner so that varied configurations can be easily studied. The algorithm uses a pseudo-collision method. Splitting with Russian roulette, suppression of absorption, and efficient scoring techniques are used to reduce the variance. The resulting code is sufficiently fast and compact to be incorporated into iterative treatments of plasma dynamics requiring numerous neutral profiles. The calculation yields the neutral gas densities, pressures, fluxes, ionization rates, momentum transfer rates, energy transfer rates, and wall sputtering rates. Applications have included modeling of proposed INTOR/FED poloidal divertor designs and other experimental devices.

  10. Verification of Monte Carlo transport codes: FLUKA, MARS and SHIELD-A

    Energy Technology Data Exchange (ETDEWEB)

    Chetvertkova, Vera [IAP, J. W. Goethe-University, Frankfurt am Main (Germany); GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Mustafin, Edil; Strasik, Ivan [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Ratzinger, Ulrich [IAP, J. W. Goethe-University, Frankfurt am Main (Germany); Latysheva, Ludmila; Sobolevskiy, Nikolai [Institute for Nuclear Research RAS, Moscow (Russian Federation)

    2011-07-01

    Monte Carlo transport codes like FLUKA, MARS and SHIELD are widely used for the estimation of radiation hazards in accelerator facilities. Accurate simulations are especially important with increasing energies and intensities of the machines. As the physical models implied in the codes are being constantly further developed, the verification is needed to make sure that the simulations give reasonable results. We report on the verification of electronic stopping modules and the verification of nuclide production modules of the codes. The verification of electronic stopping modules is based on the results of irradiation of stainless steel, copper and aluminum by 500 MeV/u and 950 MeV/u uranium ions. The stopping ranges achieved experimentally are compared with the simulated ones. The verification of isotope production modules is done via comparing the experimental depth profiles of residual activity (aluminum targets were irradiated by 500 MeV/u and 950 MeV/u uranium ions) with the results of simulations. Correspondences and discrepancies between the experiment and the simulations are discussed.

  11. Verification of Monte Carlo transport codes: FLUKA, MARS and SHIELD-A

    International Nuclear Information System (INIS)

    Monte Carlo transport codes like FLUKA, MARS and SHIELD are widely used for the estimation of radiation hazards in accelerator facilities. Accurate simulations are especially important with increasing energies and intensities of the machines. As the physical models implied in the codes are being constantly further developed, the verification is needed to make sure that the simulations give reasonable results. We report on the verification of electronic stopping modules and the verification of nuclide production modules of the codes. The verification of electronic stopping modules is based on the results of irradiation of stainless steel, copper and aluminum by 500 MeV/u and 950 MeV/u uranium ions. The stopping ranges achieved experimentally are compared with the simulated ones. The verification of isotope production modules is done via comparing the experimental depth profiles of residual activity (aluminum targets were irradiated by 500 MeV/u and 950 MeV/u uranium ions) with the results of simulations. Correspondences and discrepancies between the experiment and the simulations are discussed.

  12. A study of a transportable thermal neutron radiography unit based on a compact RFI linac

    International Nuclear Information System (INIS)

    A transportable thermal neutron radiography system, incorporating a compact proton accelerator as neutron source has been simulated using the MCNP4B code. The neutron source will be produced via the 7Li(p,n)7Be reactions by a 2.5 MeV, 10 mA proton beam into a thick lithium target. Variable values for the collimator ratio were calculated. Thermal neutron radiography parameters are comparable to the research nuclear reactors. Sapphire filter was treated in order to improve the results. Simple and advanced neutron shielding materials considered which was further enhanced with layers of bismuth. The system was compatible with the European Union Directive on 'Restriction of Hazardous Substances' (RoHS) 2002/95/EC, hence excluding the use of cadmium and lead. (author)

  13. In situ studies of mass transport in liquid alloys by means of neutron radiography.

    Science.gov (United States)

    Kargl, F; Engelhardt, M; Yang, F; Weis, H; Schmakat, P; Schillinger, B; Griesche, A; Meyer, A

    2011-06-29

    When in situ techniques became available in recent years this led to a breakthrough in accurately determining diffusion coefficients for liquid alloys. Here we discuss how neutron radiography can be used to measure chemical diffusion in a ternary AlCuAg alloy. Neutron radiography hereby gives complementary information to x-ray radiography used for measuring chemical diffusion and to quasielastic neutron scattering used mainly for determining self-diffusion. A novel Al(2)O(3) based furnace that enables one to study diffusion processes by means of neutron radiography is discussed. A chemical diffusion coefficient of Ag against Al around the eutectic composition Al(68.6)Cu(13.8)Ag(17.6) at.% was obtained. It is demonstrated that the in situ technique of neutron radiography is a powerful means to study mass transport properties in situ in binary and ternary alloys that show poor x-ray contrast. PMID:21654050

  14. Computational benchmarking of fast neutron transport throughout large water thicknesses; Benchmark theorique du transport de neutrons rapides a travers de larges epaisseurs d`eau

    Energy Technology Data Exchange (ETDEWEB)

    Risch, P.; Dekens, O.; Ait Abderrahim, H. [SCK-CEN, Fuel Research Department, (Belgium); Wouters, R. de [Tractebel, Energy Engineering, (Belgium)

    1997-10-01

    Neutron dosimetry experiments seem to point our difficulties in the treatment of large water thickness like those encountered between the core baffle and the pressure vessel. This paper describes the theoretical benchmark undertaken by EDF, SCK/CEN and TRACTEBEL ENERGY ENGINEERING, concerning the transport of fast neutrons throughout a one meter cube of water, located after a U-235 fission sources plate. The results showed no major discrepancies between the calculations up to 50 cm from the source, accepting that a P3 development of the Legendre polynomials is necessary for the Sn calculations. The main differences occurred after 50 cm, reaching 20 % at the end of the water cube. This results lead us to consider an experimental benchmark, dedicated to the problem of fast neutron deep penetration in water, which has been launched at SCK/CEN. (authors). 7 refs.

  15. Physical qualification and improvements of the numerical model of a method of characteristics for the resolution of the neutron transport equation in non-structured grids

    International Nuclear Information System (INIS)

    This research thesis addresses the resolution of the neutron transport equation inside reactor cells in non-structured grids and in general geometry by using the method of characteristics (MoC) and two acceleration methods developed during this research. The author introduces the MoC with a flat approximation of the neutron collision source within each computation area. This formulation leads to a linear approximation. The next part presents the mathematical framework for the use of the Lanczos iterative scheme. A new acceleration method is then introduced. The last part reports realistic cases with a high spatial and angular heterogeneity. Results obtained by using the Apollo2-TDT code are compared with those obtained with the Tripoli4 Monte-Carlo code

  16. Computational Transport Modeling of High-Energy Neutrons Found in the Space Environment

    Science.gov (United States)

    Cox, Brad; Theriot, Corey A.; Rohde, Larry H.; Wu, Honglu

    2012-01-01

    The high charge and high energy (HZE) particle radiation environment in space interacts with spacecraft materials and the human body to create a population of neutrons encompassing a broad kinetic energy spectrum. As an HZE ion penetrates matter, there is an increasing chance of fragmentation as penetration depth increases. When an ion fragments, secondary neutrons are released with velocities up to that of the primary ion, giving some neutrons very long penetration ranges. These secondary neutrons have a high relative biological effectiveness, are difficult to effectively shield, and can cause more biological damage than the primary ions in some scenarios. Ground-based irradiation experiments that simulate the space radiation environment must account for this spectrum of neutrons. Using the Particle and Heavy Ion Transport Code System (PHITS), it is possible to simulate a neutron environment that is characteristic of that found in spaceflight. Considering neutron dosimetry, the focus lies on the broad spectrum of recoil protons that are produced in biological targets. In a biological target, dose at a certain penetration depth is primarily dependent upon recoil proton tracks. The PHITS code can be used to simulate a broad-energy neutron spectrum traversing biological targets, and it account for the recoil particle population. This project focuses on modeling a neutron beamline irradiation scenario for determining dose at increasing depth in water targets. Energy-deposition events and particle fluence can be simulated by establishing cross-sectional scoring routines at different depths in a target. This type of model is useful for correlating theoretical data with actual beamline radiobiology experiments. Other work exposed human fibroblast cells to a high-energy neutron source to study micronuclei induction in cells at increasing depth behind water shielding. Those findings provide supporting data describing dose vs. depth across a water-equivalent medium. This

  17. Collision of Physics and Software in the Monte Carlo Application Toolkit (MCATK)

    International Nuclear Information System (INIS)

    The topic is presented in a series of slides organized as follows: MCATK overview, development strategy, available algorithms, problem modeling (sources, geometry, data, tallies), parallelism, miscellaneous tools/features, example MCATK application, recent areas of research, and summary and future work. MCATK is a C++ component-based Monte Carlo neutron-gamma transport software library with continuous energy neutron and photon transport. Designed to build specialized applications and to provide new functionality in existing general-purpose Monte Carlo codes like MCNP, it reads ACE formatted nuclear data generated by NJOY. The motivation behind MCATK was to reduce costs. MCATK physics involves continuous energy neutron & gamma transport with multi-temperature treatment, static eigenvalue (keff and α) algorithms, time-dependent algorithm, and fission chain algorithms. MCATK geometry includes mesh geometries and solid body geometries. MCATK provides verified, unit-test Monte Carlo components, flexibility in Monte Carlo application development, and numerous tools such as geometry and cross section plotters.

  18. Least-squares finite element discretizations of neutron transport equations in 3 dimensions

    Energy Technology Data Exchange (ETDEWEB)

    Manteuffel, T.A [Univ. of Colorado, Boulder, CO (United States); Ressel, K.J. [Interdisciplinary Project Center for Supercomputing, Zurich (Switzerland); Starkes, G. [Universtaet Karlsruhe (Germany)

    1996-12-31

    The least-squares finite element framework to the neutron transport equation introduced in is based on the minimization of a least-squares functional applied to the properly scaled neutron transport equation. Here we report on some practical aspects of this approach for neutron transport calculations in three space dimensions. The systems of partial differential equations resulting from a P{sub 1} and P{sub 2} approximation of the angular dependence are derived. In the diffusive limit, the system is essentially a Poisson equation for zeroth moment and has a divergence structure for the set of moments of order 1. One of the key features of the least-squares approach is that it produces a posteriori error bounds. We report on the numerical results obtained for the minimum of the least-squares functional augmented by an additional boundary term using trilinear finite elements on a uniform tesselation into cubes.

  19. Improvement of the symbolic Monte-Carlo method for the transport equation: P1 extension and coupling with diffusion

    Energy Technology Data Exchange (ETDEWEB)

    Clouet, J.F.; Samba, G. [CEA Bruyeres-le-Chatel, 91 (France)

    2005-07-01

    We use asymptotic analysis to study the diffusion limit of the Symbolic Implicit Monte-Carlo (SIMC) method for the transport equation. For standard SIMC with piecewise constant basis functions, we demonstrate mathematically that the solution converges to the solution of a wrong diffusion equation. Nevertheless a simple extension to piecewise linear basis functions enables to obtain the correct solution. This improvement allows the calculation in opaque medium on a mesh resolving the diffusion scale much larger than the transport scale. Anyway, the huge number of particles which is necessary to get a correct answer makes this computation time consuming. Thus, we have derived from this asymptotic study an hybrid method coupling deterministic calculation in the opaque medium and Monte-Carlo calculation in the transparent medium. This method gives exactly the same results as the previous one but at a much lower price. We present numerical examples which illustrate the analysis. (authors)

  20. Assessment of the neutron activation of a stainless steel sample in a Research Nuclear Reactor using the Monte Carlo method and CINDER'90

    Science.gov (United States)

    Lázaro, Ignacio; Ródenas, José; Marques, José G.; Gallardo, Sergio

    2014-06-01

    Materials in a nuclear reactor are activated by neutron irradiation. When they are withdrawn from the reactor and placed in some storage, the potential dose received by workers in the surrounding area must be taken into account. In previous papers, activation of control rods in a NPP with BWR and dose rates around the storage pool have been estimated using the MCNP5 code based on the Monte Carlo method. Models were validated comparing simulation results with experimental measurements. As the activation is mostly produced in stainless steel components of control rods the activation model can be also validated by means of experimental measurements on a stainless steel sample after being irradiated in a reactor. This has been done in the Portuguese Research Reactor at Instituto Tecnológico e Nuclear. The neutron activation has been calculated by two different methods, Monte Carlo and CINDER'90, and results have been compared. After irradiation, dose rates at the water surface of the reactor pool were measured, with the irradiated stainless steel sample submerged at different positions under water. Experimental measurements have been compared with simulation results using Monte Carlo. The comparison shows a good agreement confirming the validation of models.

  1. Qualitative Simulation of Photon Transport in Free Space Based on Monte Carlo Method and Its Parallel Implementation

    Directory of Open Access Journals (Sweden)

    Xueli Chen

    2010-01-01

    Full Text Available During the past decade, Monte Carlo method has obtained wide applications in optical imaging to simulate photon transport process inside tissues. However, this method has not been effectively extended to the simulation of free-space photon transport at present. In this paper, a uniform framework for noncontact optical imaging is proposed based on Monte Carlo method, which consists of the simulation of photon transport both in tissues and in free space. Specifically, the simplification theory of lens system is utilized to model the camera lens equipped in the optical imaging system, and Monte Carlo method is employed to describe the energy transformation from the tissue surface to the CCD camera. Also, the focusing effect of camera lens is considered to establish the relationship of corresponding points between tissue surface and CCD camera. Furthermore, a parallel version of the framework is realized, making the simulation much more convenient and effective. The feasibility of the uniform framework and the effectiveness of the parallel version are demonstrated with a cylindrical phantom based on real experimental results.

  2. Monte Carlo calculation for the development of a BNCT neutron source (1eV-10KeV) using MCNP code.

    Science.gov (United States)

    El Moussaoui, F; El Bardouni, T; Azahra, M; Kamili, A; Boukhal, H

    2008-09-01

    Different materials have been studied in order to produce the epithermal neutron beam between 1eV and 10KeV, which are extensively used to irradiate patients with brain tumors such as GBM. For this purpose, we have studied three different neutrons moderators (H(2)O, D(2)O and BeO) and their combinations, four reflectors (Al(2)O(3), C, Bi, and Pb) and two filters (Cd and Bi). Results of calculation showed that the best obtained assembly configuration corresponds to the combination of the three moderators H(2)O, BeO and D(2)O jointly to Al(2)O(3) reflector and two filter Cd+Bi optimize the spectrum of the epithermal neutron at 72%, and minimize the thermal neutron to 4% and thus it can be used to treat the deep tumor brain. The calculations have been performed by means of the Monte Carlo N (particle code MCNP 5C). Our results strongly encourage further studying of irradiation of the head with epithermal neutron fields.

  3. Flexible polyvinyl chloride neutron guides for transporting ultracold and very cold neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Arzumanov, S. S., E-mail: sarzumanov@yandex.ru; Bondarenko, L. N. [Russian Research Center Kurchatov Institute (Russian Federation); Geltenbort, P. [Institut Laue-Langevin (France); Morozov, V. I. [Russian Research Center Kurchatov Institute (Russian Federation); Nesvizhevsky, V. V. [Institut Laue-Langevin (France); Panin, Yu. N.; Strepetov, A. N.; Chuvilin, D. Yu. [Russian Research Center Kurchatov Institute (Russian Federation)

    2011-12-15

    The transmission of ultracold neutrons (UCNs) through flexible polyvinyl chloride (PVC) tubes with lengths of up to 3 m and an internal diameter of 6-8 mm has been studied. High UCN transmission is found even for arbitrarily bent tubes (single bend, double bend, triple bend, figure eight, etc.). The transmission can be improved significantly by coating the inner surface of the tube with a thin layer of liquid fluorine polymer. The prospects of these neutron guides in fundamental and applied research are discussed.

  4. Flexible polyvinyl chloride neutron guides for transporting ultracold and very cold neutrons

    International Nuclear Information System (INIS)

    The transmission of ultracold neutrons (UCNs) through flexible polyvinyl chloride (PVC) tubes with lengths of up to 3 m and an internal diameter of 6–8 mm has been studied. High UCN transmission is found even for arbitrarily bent tubes (single bend, double bend, triple bend, figure eight, etc.). The transmission can be improved significantly by coating the inner surface of the tube with a thin layer of liquid fluorine polymer. The prospects of these neutron guides in fundamental and applied research are discussed.

  5. Antiproton annihilation physics in the Monte Carlo particle transport code SHIELD-HIT12A

    Energy Technology Data Exchange (ETDEWEB)

    Taasti, Vicki Trier; Knudsen, Helge [Dept. of Physics and Astronomy, Aarhus University (Denmark); Holzscheiter, Michael H. [Dept. of Physics and Astronomy, Aarhus University (Denmark); Dept. of Physics and Astronomy, University of New Mexico (United States); Sobolevsky, Nikolai [Institute for Nuclear Research of the Russian Academy of Sciences (INR), Moscow (Russian Federation); Moscow Institute of Physics and Technology (MIPT), Dolgoprudny (Russian Federation); Thomsen, Bjarne [Dept. of Physics and Astronomy, Aarhus University (Denmark); Bassler, Niels, E-mail: bassler@phys.au.dk [Dept. of Physics and Astronomy, Aarhus University (Denmark)

    2015-03-15

    The Monte Carlo particle transport code SHIELD-HIT12A is designed to simulate therapeutic beams for cancer radiotherapy with fast ions. SHIELD-HIT12A allows creation of antiproton beam kernels for the treatment planning system TRiP98, but first it must be benchmarked against experimental data. An experimental depth dose curve obtained by the AD-4/ACE collaboration was compared with an earlier version of SHIELD-HIT, but since then inelastic annihilation cross sections for antiprotons have been updated and a more detailed geometric model of the AD-4/ACE experiment was applied. Furthermore, the Fermi–Teller Z-law, which is implemented by default in SHIELD-HIT12A has been shown not to be a good approximation for the capture probability of negative projectiles by nuclei. We investigate other theories which have been developed, and give a better agreement with experimental findings. The consequence of these updates is tested by comparing simulated data with the antiproton depth dose curve in water. It is found that the implementation of these new capture probabilities results in an overestimation of the depth dose curve in the Bragg peak. This can be mitigated by scaling the antiproton collision cross sections, which restores the agreement, but some small deviations still remain. Best agreement is achieved by using the most recent antiproton collision cross sections and the Fermi–Teller Z-law, even if experimental data conclude that the Z-law is inadequately describing annihilation on compounds. We conclude that more experimental cross section data are needed in the lower energy range in order to resolve this contradiction, ideally combined with more rigorous models for annihilation on compounds.

  6. Diagnostic and Impact Estimation of Nuclear Data Inconsistencies on Energy Deposition Calculations in Coupled Neutron-Photon Monte-Carlo Simulation, with TRIPOLI-4®

    Science.gov (United States)

    Péron, A.; Malouch, F.; Zoia, A.; Diop, C. M.

    2014-06-01

    Nuclear heating evaluation by Monte-Carlo simulation requires coupled neutron-photon calculation so as to take into account the contribution of secondary photons. Nuclear data are essential for a good calculation of neutron and photon energy deposition and for secondary photon generation. However, a number of isotopes of the most common nuclear data libraries happen to be affected by energy and/or momentum conservation errors concerning the photon production or inaccurate thresholds for photon emission sections. In this paper, we perform a comprehensive survey of the three evaluations JEFF3.1.1, JEFF3.2T2 (beta version) and ENDF/B-VII.1, over 142 isotopes. The aim of this survey is, on the one hand, to check the existence of photon production data by neutron reaction and, on the other hand, to verify the consistency of these data using the kinematic limits method recently implemented in the TRIPOLI-4 Monte-Carlo code, developed by CEA (Saclay center). Then, the impact of these inconsistencies affecting energy deposition scores has been estimated for two materials using a specific nuclear heating calculation scheme in the context of the OSIRIS Material Testing Reactor (CEA/Saclay).

  7. Neutron Transport Methods for Accelerator-Driven Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nicholas Tsoulfanidis; Elmer Lewis

    2005-02-09

    The objective of this project has been to develop computational methods that will enable more effective analysis of Accelerator Driven Systems (ADS). The work is centered at the University of Missouri at Rolla, with a subcontract at Northwestern University, and close cooperation with the Nuclear Engineering Division at Argonne National Laboratory. The work has fallen into three categories. First, the treatment of the source for neutrons originating from the spallation target which drives the neutronics calculations of the ADS. Second, the generalization of the nodal variational method to treat the R-Z geometry configurations frequently needed for scoping calculations in Accelerator Driven Systems. Third, the treatment of void regions within variational nodal methods as needed to treat the accelerator beam tube.

  8. Neutron absorber plate and radioactive material transportation cask

    International Nuclear Information System (INIS)

    Aluminum alloy flame-coating layers are formed at the outer surface of a neutron absorber plate in order to prevent corrosion due to potential difference. However, pin holes of micron order are sometimes formed on the flame-coating membranes, which are hard to be found by usual inspection. Then, ferrous flame-coating membranes are formed at the outer surface of boron carbide and aluminum alloy flame-coating membranes are formed at the outer surface thereof. The outer surface of a boron carbide plate is coated with the ferrous flame-coating membranes instead of being coated with an external plate made of neutron cells, and an aluminum alloy flame-coating membranes or mixed flame-coating layers of aluminum oxide and titania are coated thereover in order to prevent rusts. Whether the pin holes are present or not can be confirmed easily by a ferroxyl test. If there are pin holes, flame-coating is applied again to form complete membranes. Then, since it is no more necessary to fix a neutron absorbing cell at the outer surface of a fuel cell by means of welding, production cost can be reduced. (N.H.)

  9. Quantifying moisture transport in cementitious materials using neutron radiography

    Science.gov (United States)

    Lucero, Catherine L.

    A portion of the concrete pavements in the US have recently been observed to have premature joint deterioration. This damage is caused in part by the ingress of fluids, like water, salt water, or deicing salts. The ingress of these fluids can damage concrete when they freeze and expand or can react with the cementitious matrix causing damage. To determine the quality of concrete for assessing potential service life it is often necessary to measure the rate of fluid ingress, or sorptivity. Neutron imaging is a powerful method for quantifying fluid penetration since it can describe where water has penetrated, how quickly it has penetrated and the volume of water in the concrete or mortar. Neutrons are sensitive to light atoms such as hydrogen and thus clearly detect water at high spatial and temporal resolution. It can be used to detect small changes in moisture content and is ideal for monitoring wetting and drying in mortar exposed to various fluids. This study aimed at developing a method to accurately estimate moisture content in mortar. The common practice is to image the material dry as a reference before exposing to fluid and normalizing subsequent images to the reference. The volume of water can then be computed using the Beer-Lambert law. This method can be limiting because it requires exact image alignment between the reference image and all subsequent images. A model of neutron attenuation in a multi-phase cementitious composite was developed to be used in cases where a reference image is not available. The attenuation coefficients for water, un-hydrated cement, and sand were directly calculated from the neutron images. The attenuation coefficient for the hydration products was then back-calculated. The model can estimate the degree of saturation in a mortar with known mixture proportions without using a reference image for calculation. Absorption in mortars exposed to various fluids (i.e., deionized water and calcium chloride solutions) were investigated

  10. Neutron Transport and Nuclear Burnup Analysis for the Laser Inertial Confinement Fusion-Fission Energy (LIFE) Engine

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, K J; Latkowski, J F; Abbott, R P; Boyd, J K; Powers, J J; Seifried, J E

    2008-10-24

    Lawrence Livermore National Laboratory is currently developing a hybrid fusion-fission nuclear energy system, called LIFE, to generate power and burn nuclear waste. We utilize inertial confinement fusion to drive a subcritical fission blanket surrounding the fusion chamber. It is composed of TRISO-based fuel cooled by the molten salt flibe. Low-yield (37.5 MJ) targets and a repetition rate of 13.3 Hz produce a 500 MW fusion source that is coupled to the subcritical blanket, which provides an additional gain of 4-8, depending on the fuel. In the present work, we describe the neutron transport and nuclear burnup analysis. We utilize standard analysis tools including, the Monte Carlo N-Particle (MCNP) transport code, ORIGEN2 and Monteburns to perform the nuclear design. These analyses focus primarily on a fuel composed of depleted uranium not requiring chemical reprocessing or enrichment. However, other fuels such as weapons grade plutonium and highly-enriched uranium are also under consideration. In addition, we have developed a methodology using {sup 6}Li as a burnable poison to replace the tritium burned in the fusion targets and to maintain constant power over the lifetime of the engine. The results from depleted uranium analyses suggest up to 99% burnup of actinides is attainable while maintaining full power at 2GW for more than five decades.

  11. Asymptotic Analysis of Time-Dependent Neutron Transport Coupled with Isotopic Depletion and Radioactive Decay

    Energy Technology Data Exchange (ETDEWEB)

    Brantley, P S

    2006-09-27

    We describe an asymptotic analysis of the coupled nonlinear system of equations describing time-dependent three-dimensional monoenergetic neutron transport and isotopic depletion and radioactive decay. The classic asymptotic diffusion scaling of Larsen and Keller [1], along with a consistent small scaling of the terms describing the radioactive decay of isotopes, is applied to this coupled nonlinear system of equations in a medium of specified initial isotopic composition. The analysis demonstrates that to leading order the neutron transport equation limits to the standard time-dependent neutron diffusion equation with macroscopic cross sections whose number densities are determined by the standard system of ordinary differential equations, the so-called Bateman equations, describing the temporal evolution of the nuclide number densities.

  12. Monte Carlo simulation of prompt gamma-ray spectra from depleted uranium under D-T neutron irradiation and electron recoil spectra in a liquid scintillator detector

    OpenAIRE

    Qin, Jianguo; Lai, Caifeng; Liu, Rong; Zhu, Tonghua; Zhang, Xinwei; Ye, Bangjiao

    2015-01-01

    To overcome the problem of inefficient computing time and unreliable results in MCNP5 calculation, a two-step method is adopted to calculate the energy deposition of prompt gamma-rays in detectors for depleted uranium spherical shells under D-T neutrons irradiation. In the first step, the gamma-ray spectrum for energy below 7 MeV is calculated by MCNP5 code; secondly, the electron recoil spectrum in a BC501A liquid scintillator detector is simulated based on EGSnrc Monte Carlo Code with the g...

  13. User manual for version 4.3 of the Tripoli-4 Monte-Carlo method particle transport computer code; Notice d'utilisation du code Tripoli-4, version 4.3: code de transport de particules par la methode de Monte Carlo

    Energy Technology Data Exchange (ETDEWEB)

    Both, J.P.; Mazzolo, A.; Peneliau, Y.; Petit, O.; Roesslinger, B

    2003-07-01

    This manual relates to Version 4.3 TRIPOLI-4 code. TRIPOLI-4 is a computer code simulating the transport of neutrons, photons, electrons and positrons. It can be used for radiation shielding calculations (long-distance propagation with flux attenuation in non-multiplying media) and neutronic calculations (fissile medium, criticality or sub-criticality basis). This makes it possible to calculate k{sub eff} (for criticality), flux, currents, reaction rates and multi-group cross-sections. TRIPOLI-4 is a three-dimensional code that uses the Monte-Carlo method. It allows for point-wise description in terms of energy of cross-sections and multi-group homogenized cross-sections and features two modes of geometrical representation: surface and combinatorial. The code uses cross-section libraries in ENDF/B format (such as JEF2-2, ENDF/B-VI and JENDL) for point-wise description cross-sections in APOTRIM format (from the APOLLO2 code) or a format specific to TRIPOLI-4 for multi-group description. (authors)

  14. Monte Carlo simulations and benchmark measurements on the response of TE(TE) and Mg(Ar) ionization chambers in photon, electron and neutron beams

    Science.gov (United States)

    Lin, Yi-Chun; Huang, Tseng-Te; Liu, Yuan-Hao; Chen, Wei-Lin; Chen, Yen-Fu; Wu, Shu-Wei; Nievaart, Sander; Jiang, Shiang-Huei

    2015-06-01

    The paired ionization chambers (ICs) technique is commonly employed to determine neutron and photon doses in radiology or radiotherapy neutron beams, where neutron dose shows very strong dependence on the accuracy of accompanying high energy photon dose. During the dose derivation, it is an important issue to evaluate the photon and electron response functions of two commercially available ionization chambers, denoted as TE(TE) and Mg(Ar), used in our reactor based epithermal neutron beam. Nowadays, most perturbation corrections for accurate dose determination and many treatment planning systems are based on the Monte Carlo technique. We used general purposed Monte Carlo codes, MCNP5, EGSnrc, FLUKA or GEANT4 for benchmark verifications among them and carefully measured values for a precise estimation of chamber current from absorbed dose rate of cavity gas. Also, energy dependent response functions of two chambers were calculated in a parallel beam with mono-energies from 20 keV to 20 MeV photons and electrons by using the optimal simple spherical and detailed IC models. The measurements were performed in the well-defined (a) four primary M-80, M-100, M120 and M150 X-ray calibration fields, (b) primary 60Co calibration beam, (c) 6 MV and 10 MV photon, (d) 6 MeV and 18 MeV electron LINACs in hospital and (e) BNCT clinical trials neutron beam. For the TE(TE) chamber, all codes were almost identical over the whole photon energy range. In the Mg(Ar) chamber, MCNP5 showed lower response than other codes for photon energy region below 0.1 MeV and presented similar response above 0.2 MeV (agreed within 5% in the simple spherical model). With the increase of electron energy, the response difference between MCNP5 and other codes became larger in both chambers. Compared with the measured currents, MCNP5 had the difference from the measurement data within 5% for the 60Co, 6 MV, 10 MV, 6 MeV and 18 MeV LINACs beams. But for the Mg(Ar) chamber, the derivations reached 7

  15. In situ neutron depth profiling: A powerful method to probe lithium transport in micro-batteries

    NARCIS (Netherlands)

    Oudenhoven, J.F.M.; Labohm, F.; Mulder, M.; Niessen, R.A.H.; Mulder, F.M.; Notten, P.H.L.

    2011-01-01

    In situ neutron depth profiling (NDP) offers the possibility to observe lithium transport inside micro-batteries during battery operation. It is demonstrated that NDP results are consistent with the results of electrochemical measurements, and that the use of an enriched6LiCoO2 cathode offers more i

  16. The neutron transport code DTF-Traca users manual and input data

    Energy Technology Data Exchange (ETDEWEB)

    Ahnert, C.

    1979-07-01

    This is a users manual of the neutron transport code DTF-TRACA, which is a version of the original DTF-IV with some modifications made at JEN. A detailed input data descriptions is given. The new options developed at JEN are included too. (Author) 18 refs.

  17. Existence result for the kinetic neutron transport problem with a general albedo boundary condition

    International Nuclear Information System (INIS)

    We present an existence result for the kinetic neutron transport equation with a general albedo boundary condition. The proof is constructive in the sense that we build a sequence that converges to the solution of the problem by iterating on the albedo term. Both nonhomogeneous and albedo boundary conditions are studied. (authors)

  18. Two-group neutron transport theory in adjacent space with lineary anisotropic scattering

    International Nuclear Information System (INIS)

    A solution method for two-group neutron transport theory with anisotropic scattering is introduced by the combination of case method (expansion method of self singular function) and the invariant imbedding (invariance principle). The numerical results for the Milne problem in light water and borated water is presented to demonstrate the avalibility of the method

  19. The adjoint neutron transport equation and the statistical approach for its solution

    CERN Document Server

    Saracco, Paolo; Ravetto, Piero

    2016-01-01

    The adjoint equation was introduced in the early days of neutron transport and its solution, the neutron importance, has ben used for several applications in neutronics. The work presents at first a critical review of the adjoint neutron transport equation. Afterwards, the adjont model is constructed for a reference physical situation, for which an analytical approach is viable, i.e. an infinite homogeneous scattering medium. This problem leads to an equation that is the adjoint of the slowing-down equation that is well-known in nuclear reactor physics. A general closed-form analytical solution to such adjoint equation is obtained by a procedure that can be used also to derive the classical Placzek functions. This solution constitutes a benchmark for any statistical or numerical approach to the adjoint equation. A sampling technique to evaluate the adjoint flux for the transport equation is then proposed and physically interpreted as a transport model for pseudo-particles. This can be done by introducing appr...

  20. Recoil proton, alpha particle, and heavy ion impacts on microdosimetry and RBE of fast neutrons: analysis of kerma spectra calculated by Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Pignol, J.-P. [Toronto-Sunnybrook Regional Cancer Centre, Radiotherapy Dept., Toronto, Ontario (Canada); Slabbert, J. [National Accelerator Centre, Faure (South Africa)

    2001-02-01

    Fast neutrons (FN) have a higher radio-biological effectiveness (RBE) compared with photons, however the mechanism of this increase remains a controversial issue. RBE variations are seen among various FN facilities and at the same facility when different tissue depths or thicknesses of hardening filters are used. These variations lead to uncertainties in dose reporting as well as in the comparisons of clinical results. Besides radiobiology and microdosimetry, another powerful method for the characterization of FN beams is the calculation of total proton and heavy ion kerma spectra. FLUKA and MCNP Monte Carlo code were used to simulate these kerma spectra following a set of microdosimetry measurements performed at the National Accelerator Centre. The calculated spectra confirmed major classical statements: RBE increase is linked to both slow energy protons and alpha particles yielded by (n,{alpha}) reactions on carbon and oxygen nuclei. The slow energy protons are produced by neutrons having an energy between 10 keV and 10 MeV, while the alpha particles are produced by neutrons having an energy between 10 keV and 15 MeV. Looking at the heavy ion kerma from <15 MeV and the proton kerma from neutrons <10 MeV, it is possible to anticipate y* and RBE trends. (author)

  1. Monte Carlo assessment of soil moisture effect on high-energy thermal neutron capture gamma-ray by {sup 14}N

    Energy Technology Data Exchange (ETDEWEB)

    Pazirandeh, Ali [Physics Department, University of Tehran, Tehran (Iran, Islamic Republic of) and Institute for Theoretical and Applied Physics, Tabriz (Iran, Islamic Republic of)]. E-mail: paziran@ut.ac.ir; Azizi, Maryam [Physics Department, University of Tehran, Tehran (Iran, Islamic Republic of); Institute for Theoretical and Applied Physics, Tabriz (Iran, Islamic Republic of); Farhad Masoudi, S. [Physics Department, University of Tehran, Tehran (Iran, Islamic Republic of); Institute for Theoretical and Applied Physics, Tabriz (Iran, Islamic Republic of)

    2006-01-01

    Among many conventional techniques, nuclear techniques have shown to be faster, more reliable, and more effective in detecting explosives. In the present work, neutrons from a 5 Ci Am-Be neutron source being in water tank are captured by elements of soil and landmine (TNT), namely {sup 14}N, H, C, and O. The prompt capture gamma-ray spectrum taken by a NaI (Tl) scintillation detector indicates the characteristic photo peaks of the elements in soil and landmine. In the high-energy region of the gamma-ray spectrum, besides 10.829 MeV of {sup 15}N, single escape (SE) and double escape (DE) peaks are unmistakable photo peaks, which make the detection of concealed explosive possible. The soil has the property of moderating neutrons as well as diffusing the thermal neutron flux. Among many elements in soil, silicon is more abundant and {sup 29}Si emits 10.607 MeV prompt capture gamma-ray, which makes 10.829 MeV detection difficult. The Monte Carlo simulation was used to adjust source-target-detector distances and soil moisture content to yield the best result. Therefore, we applied MCNP4C for configuration very close to reality of a hidden landmine in soil.

  2. Development of a Monte Carlo software to photon transportation in voxel structures using graphic processing units; Desenvolvimento de um software de Monte Carlo para transporte de fotons em estruturas de voxels usando unidades de processamento grafico

    Energy Technology Data Exchange (ETDEWEB)

    Bellezzo, Murillo

    2014-09-01

    As the most accurate method to estimate absorbed dose in radiotherapy, Monte Carlo Method (MCM) has been widely used in radiotherapy treatment planning. Nevertheless, its efficiency can be improved for clinical routine applications. In this thesis, the CUBMC code is presented, a GPU-based MC photon transport algorithm for dose calculation under the Compute Unified Device Architecture (CUDA) platform. The simulation of physical events is based on the algorithm used in PENELOPE, and the cross section table used is the one generated by the MATERIAL routine, also present in PENELOPE code. Photons are transported in voxel-based geometries with different compositions. There are two distinct approaches used for transport simulation. The rst of them forces the photon to stop at every voxel frontier, the second one is the Woodcock method, where the photon ignores the existence of borders and travels in homogeneous fictitious media. The CUBMC code aims to be an alternative of Monte Carlo simulator code that, by using the capability of parallel processing of graphics processing units (GPU), provide high performance simulations in low cost compact machines, and thus can be applied in clinical cases and incorporated in treatment planning systems for radiotherapy. (author)

  3. Analytical three-dimensional neutron transport benchmarks for verification of nuclear engineering codes. Final report

    International Nuclear Information System (INIS)

    Because of the requirement of accountability and quality control in the scientific world, a demand for high-quality analytical benchmark calculations has arisen in the neutron transport community. The intent of these benchmarks is to provide a numerical standard to which production neutron transport codes may be compared in order to verify proper operation. The overall investigation as modified in the second year renewal application includes the following three primary tasks. Task 1 on two dimensional neutron transport is divided into (a) single medium searchlight problem (SLP) and (b) two-adjacent half-space SLP. Task 2 on three-dimensional neutron transport covers (a) point source in arbitrary geometry, (b) single medium SLP, and (c) two-adjacent half-space SLP. Task 3 on code verification, includes deterministic and probabilistic codes. The primary aim of the proposed investigation was to provide a suite of comprehensive two- and three-dimensional analytical benchmarks for neutron transport theory applications. This objective has been achieved. The suite of benchmarks in infinite media and the three-dimensional SLP are a relatively comprehensive set of one-group benchmarks for isotropically scattering media. Because of time and resource limitations, the extensions of the benchmarks to include multi-group and anisotropic scattering are not included here. Presently, however, enormous advances in the solution for the planar Green's function in an anisotropically scattering medium have been made and will eventually be implemented in the two- and three-dimensional solutions considered under this grant. Of particular note in this work are the numerical results for the three-dimensional SLP, which have never before been presented. The results presented were made possible only because of the tremendous advances in computing power that have occurred during the past decade

  4. Analytical three-dimensional neutron transport benchmarks for verification of nuclear engineering codes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Ganapol, B.D.; Kornreich, D.E. [Univ. of Arizona, Tucson, AZ (United States). Dept. of Nuclear Engineering

    1997-07-01

    Because of the requirement of accountability and quality control in the scientific world, a demand for high-quality analytical benchmark calculations has arisen in the neutron transport community. The intent of these benchmarks is to provide a numerical standard to which production neutron transport codes may be compared in order to verify proper operation. The overall investigation as modified in the second year renewal application includes the following three primary tasks. Task 1 on two dimensional neutron transport is divided into (a) single medium searchlight problem (SLP) and (b) two-adjacent half-space SLP. Task 2 on three-dimensional neutron transport covers (a) point source in arbitrary geometry, (b) single medium SLP, and (c) two-adjacent half-space SLP. Task 3 on code verification, includes deterministic and probabilistic codes. The primary aim of the proposed investigation was to provide a suite of comprehensive two- and three-dimensional analytical benchmarks for neutron transport theory applications. This objective has been achieved. The suite of benchmarks in infinite media and the three-dimensional SLP are a relatively comprehensive set of one-group benchmarks for isotropically scattering media. Because of time and resource limitations, the extensions of the benchmarks to include multi-group and anisotropic scattering are not included here. Presently, however, enormous advances in the solution for the planar Green`s function in an anisotropically scattering medium have been made and will eventually be implemented in the two- and three-dimensional solutions considered under this grant. Of particular note in this work are the numerical results for the three-dimensional SLP, which have never before been presented. The results presented were made possible only because of the tremendous advances in computing power that have occurred during the past decade.

  5. On the use of monte Carlo perturbation in neutron transport problems

    International Nuclear Information System (INIS)

    Two methods to estimate the variations on the collision density between different configurations are presented: the 'multiple estimate method' and the 'Taylor expansion method'. First and foremost, we recall the bases of analogue simulation and present the notations used to define the collision density in the integral Boltzmann equation. In the second part we discuss the different non analogue techniques used to obtain a small variance. The third part of this work deals with correlated sampling that we call multiple estimate. The principle is similar to non analogue simulation when we introduce a biased law to simulate the propagation of particles. Finally, we calculate perturbed results owing to a Taylor expansion following Rief's nice representation. We extend the method to an arbitrary order of the Taylor expansion for one and two variables. We present several examples and bring in light the advantages and drawbacks of the 'multiple estimate method' and the 'Taylor expansion method'. In every case, we compare the collision densities estimated by these two methods with the collision densities estimated by independent simulations. (author)

  6. Post-merger evolution of a neutron star-black hole binary with neutrino transport

    CERN Document Server

    Foucart, Francois; Roberts, Luke; Duez, Matthew D; Haas, Roland; Kidder, Lawrence E; Ott, Christian D; Pfeiffer, Harald P; Scheel, Mark A; Szilagyi, Bela

    2015-01-01

    We present a first simulation of the post-merger evolution of a black hole-neutron star binary in full general relativity using an energy-integrated general relativistic truncated moment formalism for neutrino transport. We describe our implementation of the moment formalism and important tests of our code, before studying the formation phase of a disk after a black hole-neutron star merger. We use as initial data an existing general relativistic simulation of the merger of a neutron star of 1.4 solar mass with a black hole of 7 solar mass and dimensionless spin a/M=0.8. Comparing with a simpler leakage scheme for the treatment of the neutrinos, we find noticeable differences in the neutron to proton ratio in and around the disk, and in the neutrino luminosity. We find that the electron neutrino luminosity is much lower in the transport simulations, and that the remnant is less neutron-rich. The spatial distribution of the neutrinos is significantly affected by relativistic effects. Over the short timescale e...

  7. The use of neutron generators for the detection of illicit materials in the sea transportation system

    International Nuclear Information System (INIS)

    In today's society acts of terrorism must involve in some stages the illicit trafficking either of explosives, chemical agents and/or nuclear materials. Therefore society must rely on an anti-trafficking infrastructure which encompasses responsible authorities, field personnel and adequate instrumental networks. Modern inspection systems for personnel, parcel, vehicle and cargo, as noninvasive imaging techniques, are based on the use of nuclear analytical methods. The inspection systems make use of penetrating radiation (neutrons, gamma and x-rays) in a scanning geometry, with the detection of radiation either transmitted or produced in the interrogated object. Explosives and chemical agent detection systems are based on the fact that the problem of identification can be reduced to the measurement of elemental concentrations. Different nuclear analytical techniques could be used for this purpose; however the use of neutrons has some specific advantages due to the high penetrability in large payloads. Of special interest is the design and use of a transportable neutron system coupled to a gamma-ray radiographic device for inspecting large containers searching for contraband, explosives, weapons etc. The use of neutron induced reactions for non-destructive bulk elemental analysis is well documented. All neutrons, in particular fast neutrons, are well suited to explore large volume samples because of their high penetration in bulk material. Fast neutrons can be produced efficiently and economically by natural radioactive sources, small accelerators or compact electronic neutron generators, making possible the use of neutron based techniques in field applications. Gamma-rays produced by irradiating the sample with neutrons gives the elemental composition of the material, moreover, knowing the nuclear cross-sections and estimating the absorption factors in the different materials, it is possible to perform a quantitative analysis of elements in the sample even in depth

  8. Numerical solution of neutron transport equations in discrete ordinates and slab geometry

    International Nuclear Information System (INIS)

    An unified formalism to solve numerically, between other equation, the neutron transport in discrete ordinates, slab geometry, several energy groups and independents of time, has been developed recently. Such a formalism cover some of the conventional schemes as diamond difference, (WDD) characteristic step (SC) lineal characteristic (LC), quadratic characteristic (QC) and lineal discontinuous. Unified formation gives before hand the convergence order of the previously selected scheme. In fact it allows besides to generate a big amount of numerical schemes, with which is also possible to solve numerical equations as soon as neutron transport. The essential purpose of this work was to solve the neutron transport equations in slab geometry and discrete ordinates considering several energy groups without to take under advisement time dependence based in the above mentioned unified formalism. To reach this purpose it was necesary to design a computer code with the name TNOD1 (Neutron transport in discrete ordinates and 1 dimension) which includes each one of the schemes already pointed out. there exist two numerical schemes, also recently developed, quadratic continuous (QC) and cubic continuous (CN), although covered by unified formalism, it has been possible to include them inside this computer code without make substantial changes in its structure. In chapter I, derivative of neutron transport equation independent of time is taken, for angular flux, including boundary conditions and discontinuity. In chapter II the neutron transport equations are obtained in multigroups, independents of time, for approximation of discrete ordinates. Description of theory related with unified formalism and its relationship with mentioned discretization schemes is presented in chapter III. Chapter IV describes the computer code developed and finally, in chapter V different numerical results obtained with TNOD1 program are shown. In Appendix A theorems and mathematical arguments used

  9. NASA astronaut dosimetry: Implementation of scalable human phantoms and benchmark comparisons of deterministic versus Monte Carlo radiation transport

    Science.gov (United States)

    Bahadori, Amir Alexander

    Astronauts are exposed to a unique radiation environment in space. United States terrestrial radiation worker limits, derived from guidelines produced by scientific panels, do not apply to astronauts. Limits for astronauts have changed throughout the Space Age, eventually reaching the current National Aeronautics and Space Administration limit of 3% risk of exposure induced death, with an administrative stipulation that the risk be assured to the upper 95% confidence limit. Much effort has been spent on reducing the uncertainty associated with evaluating astronaut risk for radiogenic cancer mortality, while tools that affect the accuracy of the calculations have largely remained unchanged. In the present study, the impacts of using more realistic computational phantoms with size variability to represent astronauts with simplified deterministic radiation transport were evaluated. Next, the impacts of microgravity-induced body changes on space radiation dosimetry using the same transport method were investigated. Finally, dosimetry and risk calculations resulting from Monte Carlo radiation transport were compared with results obtained using simplified deterministic radiation transport. The results of the present study indicated that the use of phantoms that more accurately represent human anatomy can substantially improve space radiation dose estimates, most notably for exposures from solar particle events under light shielding conditions. Microgravity-induced changes were less important, but results showed that flexible phantoms could assist in optimizing astronaut body position for reducing exposures during solar particle events. Finally, little overall differences in risk calculations using simplified deterministic radiation transport and 3D Monte Carlo radiation transport were found; however, for the galactic cosmic ray ion spectra, compensating errors were observed for the constituent ions, thus exhibiting the need to perform evaluations on a particle

  10. Ageing of a neutron shielding used in transport/storage casks

    Energy Technology Data Exchange (ETDEWEB)

    Nizeyiman, Fidele; Alami, Aatif; Issard, Herve; Bellenger, Veronique [TN International, 1 rue des herons, Montigny le Bretonneux, 78054 Saint Quentin en Yvelines (France); Laboratoire PIMM, Arts and Metiers ParisTech, 151 Bd de l' Hopital, 75013 Paris (France)

    2012-07-11

    In radioactive materials transport/storage casks, a mineral-filled vinylester composite is used for neutron shielding which relies on its hydrogen and boron atoms content. During cask service life, this composite is mainly subjected to three types of ageing: hydrothermal ageing, thermal oxidation and neutron irradiation. The aim of this study is to investigate the effect of hydrothermal ageing on the properties and chemical composition of this polymer composite. At high temperature (120 Degree-Sign C and 140 Degree-Sign C), the main consequence is the strong decrease of mechanical properties induced by the filler/matrix debonding.

  11. Development of a 1D neutron transport code employing the method of characteristics

    International Nuclear Information System (INIS)

    To investigate the 2D/1D fusion core analysis method, a 1D neutron transport problem solver, PEACH-ID, is developed. It is a code of method of characteristics (MOC), both the usual fiat-source step characteristics (SC) scheme and linear source (LS) approximation scheme are adopted for tracking calculation along the neutron flying trajectory. Exponential function interpolation table and fission source extrapolation are adopted as two major methods to accelerate the computational process. Numerical results demonstrate that PEACH-1D is accurate and efficient, and the proposed LS scheme is able to handle quite larger mesh division and deserves much more application in the MOC codes. (authors)

  12. Monte Carlo simulations of the secondary neutron ambient and effective dose equivalent rates from surface to suborbital altitudes and low Earth orbit

    Science.gov (United States)

    El-Jaby, Samy; Richardson, Richard B.

    2015-07-01

    Occupational exposures from ionizing radiation are currently regulated for airline travel (tourism vehicles will reach suborbital altitudes of approximately 100 km and, therefore, the annual occupational dose to flight crew during repeated transits is expected to fall somewhere between those observed for aircrew and astronauts. Unfortunately, measurements of the radiation environment at the high altitudes reached by suborbital vehicles are sparse, and modelling efforts have been similarly limited. In this paper, preliminary MCNPX radiation transport code simulations are developed of the secondary neutron flux profile in air from surface altitudes up to low Earth orbit at solar minimum conditions and excluding the effects of spacecraft shielding. These secondary neutrons are produced by galactic cosmic radiation interacting with Earth's atmosphere and are among the sources of radiation that can pose a health risk. Associated estimates of the operational neutron ambient dose equivalent, used for radiation protection purposes, and the neutron effective dose equivalent that is typically used for estimates of stochastic health risks, are provided in air. Simulations show that the neutron radiation dose rates received at suborbital altitudes are comparable to those experienced by aircrew flying at 7 to 14 km. We also show that the total neutron dose rate tails off beyond the Pfotzer maximum on ascension from surface up to low Earth orbit.

  13. An Overview of the Monte Carlo Application ToolKit (MCATK)

    Energy Technology Data Exchange (ETDEWEB)

    Trahan, Travis John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-01-07

    MCATK is a C++ component-based Monte Carlo neutron-gamma transport software library designed to build specialized applications and designed to provide new functionality in existing general-purpose Monte Carlo codes like MCNP; it was developed with Agile software engineering methodologies under the motivation to reduce costs. The characteristics of MCATK can be summarized as follows: MCATK physics – continuous energy neutron-gamma transport with multi-temperature treatment, static eigenvalue (k and α) algorithms, time-dependent algorithm, fission chain algorithms; MCATK geometry – mesh geometries, solid body geometries. MCATK provides verified, unit-tested Monte Carlo components, flexibility in Monte Carlo applications development, and numerous tools such as geometry and cross section plotters. Recent work has involved deterministic and Monte Carlo analysis of stochastic systems. Static and dynamic analysis is discussed, and the results of a dynamic test problem are given.

  14. Simulation response of B4C-coated PPAC for thermal neutrons using GEANT4 Monte Carlo approach

    Science.gov (United States)

    Jamil, M.; Rhee, J. T.; Jeon, Y. J.

    2013-08-01

    In this work we report a technique employed for the detection of thermal neutrons using the parallel plate avalanche counter (PPAC). In order to make the detector sensitive to thermal neutrons a thin layer of B4C has been coated on the forward electrode of the PPAC configuration. Upon falling on the converter coating, charged particles were generated via the 10B (n , α)7Li reaction. In this simulation study, thermal neutrons have been simulated using the GEANT4 MC code, and the response of the detector has been evaluated as a function of neutron energy. For a better understanding of the simulation response, the performance of the detector has been found using the two different physics list i.e., QGSP _ BIC _ HP and QGSP _ BERT _ HP. The obtained results predict that such boron-carbide based PPAC can be potentially utilized for thermal neutron detection. A complete description of the detector configuration and the simulation results is also presented.

  15. Verification of Three Dimensional Triangular Prismatic Discrete Ordinates Transport Code ENSEMBLE-TRIZ by Comparison with Monte Carlo Code GMVP

    Science.gov (United States)

    Homma, Yuto; Moriwaki, Hiroyuki; Ohki, Shigeo; Ikeda, Kazumi

    2014-06-01

    This paper deals with verification of three dimensional triangular prismatic discrete ordinates transport calculation code ENSEMBLE-TRIZ by comparison with multi-group Monte Carlo calculation code GMVP in a large fast breeder reactor. The reactor is a 750 MWe electric power sodium cooled reactor. Nuclear characteristics are calculated at beginning of cycle of an initial core and at beginning and end of cycle of equilibrium core. According to the calculations, the differences between the two methodologies are smaller than 0.0002 Δk in the multi-plication factor, relatively about 1% in the control rod reactivity, and 1% in the sodium void reactivity.

  16. A Monte Carlo Method for the Analysis of Gamma Radiation Transport from Distributed Sources in Laminated Shields

    International Nuclear Information System (INIS)

    A description is given of a method for calculating the penetration and energy deposition of gamma radiation, based on Monte Carlo techniques. The essential feature is the application of the exponential transformation to promote the transport of penetrating quanta and to balance the steep spatial variations of the source distributions which appear in secondary gamma emission problems. The estimated statistical errors in a number of sample problems, involving concrete shields with thicknesses up to 500 cm, are shown to be quite favorable, even at relatively short computing times. A practical reactor shielding problem is also shown and the predictions compared with measurements

  17. Variance analysis of the Monte Carlo perturbation source method in inhomogeneous linear particle transport problems. Derivation of formulae

    International Nuclear Information System (INIS)

    The perturbation source method is used in the Monte Carlo method in calculating small effects in a particle field. It offers primising possibilities for introducing positive correlation between subtracting estimates even in the cases where other methods fail, in the case of geometrical variations of a given arrangement. The perturbation source method is formulated on the basis of integral equations for the particle fields. The formulae for the second moment of the difference of events are derived. Explicity a certain class of transport games and different procedures for generating the so-called perturbation particles are considered

  18. Correlation of electron transport and photocatalysis of nanocrystalline clusters studied by Monte-Carlo continuity random walking.

    Science.gov (United States)

    Liu, Baoshun; Li, Ziqiang; Zhao, Xiujian

    2015-02-21

    In this research, Monte-Carlo Continuity Random Walking (MC-RW) model was used to study the relation between electron transport and photocatalysis of nano-crystalline (nc) clusters. The effects of defect energy disorder, spatial disorder of material structure, electron density, and interfacial transfer/recombination on the electron transport and the photocatalysis were studied. Photocatalytic activity is defined as 1/τ from a statistical viewpoint with τ being the electron average lifetime. Based on the MC-RW simulation, a clear physical and chemical "picture" was given for the photocatalytic kinetic analysis of nc-clusters. It is shown that the increase of defect energy disorder and material spatial structural disorder, such as the decrease of defect trap number, the increase of crystallinity, the increase of particle size, and the increase of inter-particle connection, can enhance photocatalytic activity through increasing electron transport ability. The increase of electron density increases the electron Fermi level, which decreases the activation energy for electron de-trapping from traps to extending states, and correspondingly increases electron transport ability and photocatalytic activity. Reducing recombination of electrons and holes can increase electron transport through the increase of electron density and then increases the photocatalytic activity. In addition to the electron transport, the increase of probability for electrons to undergo photocatalysis can increase photocatalytic activity through the increase of the electron interfacial transfer speed.

  19. Comparison of neutronic transport equation resolution nodal methods

    International Nuclear Information System (INIS)

    In this work, some transport equation resolution nodal methods are comparatively studied: the constant-constant (CC), linear-nodal (LN) and the constant-quadratic (CQ). A nodal scheme equivalent to finite differences has been used for its programming, permitting its inclusion in existing codes. Some bidimensional problems have been solved, showing that linear-nodal (LN) are, in general, obtained with accuracy in CPU shorter times. (Author)

  20. VIM4.0, Stead-State 3-D Neutron Transport Using ENDF/B or Multigroup Cross Sections

    International Nuclear Information System (INIS)

    1 - Description of program or function: VIM solves the steady-state neutron or photon transport problem in any detailed three-dimensional geometry using either continuous energy-dependent ENDF nuclear data or multigroup cross sections. Neutron transport is carried out in a criticality mode, or in a fixed source mode (optionally incorporating subcritical multiplication). Photon transport is simulated in the fixed source mode. The geometry options are infinite medium, combinatorial geometry, and hexagonal or rectangular lattices of combinatorial geometry unit cells, and rectangular lattices of cells of assembled plates. Boundary conditions include vacuum, specular and white reflection, and periodic boundaries for reactor cell calculations. The VIM 4.0 distribution includes data from ENDF/B-IV, ENDF/B-V, ENDF/B-VI and JEF2.2. Binary sequential data libraries for use with the code system on IBM or Sun workstations are included. ASCII data libraries and a convenient means to convert them to binary on a target machine are included for users on other systems. In addition to be included in the RSICC distribution files, the VIM User Guide is available on the developer's web site http://www.ra.anl.gov/vimguide/. 2 - Methods:VIM uses standard Monte Carlo methods for particle tracking with several optional variance-reduction techniques. These include splitting/Russian roulette, non-terminating absorption with non-analog weight cutoff energy. The keff is determined by the optimum linear combinations of two of the three eigenvalue estimates - analog, collision, and track length. Resonance and smooth cross sections are specified pointwise with linear-linear interpolation, frequently with many thousands of energy points. Unresolved resonances are described by the probability table method, which allows the statistical nature of the evaluated resonance cross sections to be incorporated naturally into self-shielding. Neutron interactions are elastic, inelastic and thermal scattering

  1. Development of Monte Carlo depletion code MCDEP

    Energy Technology Data Exchange (ETDEWEB)

    Kim, K. S.; Kim, K. Y.; Lee, J. C.; Ji, S. K. [KAERI, Taejon (Korea, Republic of)

    2003-07-01

    Monte Carlo neutron transport calculation has been used to obtain a reference solution in reactor physics analysis. The typical and widely-used Monte Carlo transport code is MCNP (Monte Carlo N-Particle Transport Code) developed in Los Alamos National Laboratory. The drawbacks of Monte-Carlo transport codes are the lacks of the capacities for the depletion and temperature dependent calculations. In this research we developed MCDEP (Monte Carlo Depletion Code Package) using MCNP with the capacity of the depletion calculation. This code package is the integration of MCNP and depletion module of ORIGEN-2 using the matrix exponential method. This code package enables the automatic MCNP and depletion calculations only with the initial MCNP and MCDEP inputs prepared by users. Depletion chains were simplified for the efficiency of computing time and the treatment of short-lived nuclides without cross section data. The results of MCDEP showed that the reactivity and pin power distributions for the PWR fuel pins and assemblies are consistent with those of CASMO-3 and HELIOS.

  2. Reference neutron transport calculation note for Korea nuclear power plants with 3-loop PWR reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Byung Cheol; Chang, Ki Oak

    1997-05-01

    Reactor pressure vessel (RPV) steels are subjected to neutron irradiation at a temperature of about 290 deg C. This radiation exposure alters the mechanical properties, leading to a shift of the brittle-to-ductile transition temperature toward higher temperatures and to a diminution of the rupture energy as determined by Charpy V-notch tests. This radiation embrittlement is one of the important aging factors of nuclear power plants. U.S. NRC recommended the basic requirements for the determination of the pressure vessel fluence by regulatory guide DG-1025 in order to reduce the uncertainty in the determination of neutron fluence calculation and measurements. The determination of the pressure vessel fluence is based on both calculations and measurements. The fluence prediction is made with a calculation and the measurements are used to qualify the calculational methodology. Because of the importance and the difficulty of these calculations, the method`s qualification by comparison to measurement must be made to ensure a reliable and accurate vessel fluence determination. This reference calculation note is to provide a series of forward and adjoint neutron transport calculations for use in the evaluation of neutron dosimetry from surveillance capsule irradiations at 3-loop PWR reactor as well as for use in the determination of the neutron exposure of the reactor vessel wall in accordance with U.S Regulatory Guide DG-1025 requirements. The calculations of the pressure vessel fluence consist of the following steps; (1) Determination of the geometrical and material input data, (2) Determination of the core neutron source, and (3) Propagation of the neutron fluence from the core to the vessel and into the cavity. (author). 12 tabs., 3 figs., 7 refs.

  3. Sampling of transport coefficients in steady state Townsend Monte Carlo simulation

    International Nuclear Information System (INIS)

    In this paper a complete and consistent set of equations for sampling of the data in steady state Townsend (SST) Monte Carlo simulations (MCS) is developed. Standard implementation of a Monte Carlo simulation code for time of flight (TOF) allows us to add SST sampling. Membrane's sampling has an advantage in obtaining spatial variation of properties with high spatial resolution but with a problem in poor statistics for low energy electrons that move perpendicular to the field axis. The box sampling overcomes this problem but suffers from a poorer statistics than membrane sampling. The results show the effect of non-conservative collisions in the difference between SST and TOF results. In addition the internal consistency between two methods of SST sampling is very good. The present paper also gives a complete set of equations for conversion between the two types of experiments TOF and SST. Our simulation provided us also with a way to test the conversion formulae and their convergence

  4. Neutron- and proton-induced evaluated transport library up to 150 MeV

    International Nuclear Information System (INIS)

    A new evaluated nuclear data library has been created. The library consists of two sub-libraries for neutron and proton incident particles. The neutron sub-library contains nuclear data for transport, heating and shielding applications for 242 nuclides with atomic numbers ranging from 8 to 82 in the energy region of primary neutrons from 10-5 eV to 150 MeV. Data below 20 MeV are taken mainly from ENDF/B-VI (revision 8) and for some nuclides, from the JENDL-3.3 and JEFF-3.0 libraries. The proton sub-library should contain data for the same range of target nuclides and energies. Proton-induced evaluated cross-section files are available for 15 nuclides at the moment. The evaluation of emitted particle energy and angular distributions at energies above 20 MeV (for incident neutrons) and above the reaction threshold (for incident protons) was performed with the help of the ALICE/ASH code and the analysis of available experimental data. The total cross-sections, elastic cross-sections and elastic scattering angular distributions were calculated with the help of the coupled channel model. The results of the calculation were adjusted to the data from ENDF/B-VI, JENDL-3.3, or JEFF-3.0 at the neutron energy equal to 20 MeV. The library is written in ENDF-6 format using the MF=3/MT=5 and MF=6/MT=5 representations

  5. An improved Monte Carlo study of coherent scattering effects of low energy charged particle transport in Percus-Yevick liquids

    CERN Document Server

    Tattersall, W J; Boyle, G J; White, R D

    2015-01-01

    We generalize a simple Monte Carlo (MC) model for dilute gases to consider the transport behavior of positrons and electrons in Percus-Yevick model liquids under highly non-equilibrium conditions, accounting rigorously for coherent scattering processes. The procedure extends an existing technique [Wojcik and Tachiya, Chem. Phys. Lett. 363, 3--4 (1992)], using the static structure factor to account for the altered anisotropy of coherent scattering in structured material. We identify the effects of the approximation used in the original method, and develop a modified method that does not require that approximation. We also present an enhanced MC technique that has been designed to improve the accuracy and flexibility of simulations in spatially-varying electric fields. All of the results are found to be in excellent agreement with an independent multi-term Boltzmann equation solution, providing benchmarks for future transport models in liquids and structured systems.

  6. A fast GPU-based Monte Carlo simulation of proton transport with detailed modeling of non-elastic interactions

    CERN Document Server

    Tseung, H Wan Chan; Beltran, C

    2014-01-01

    Purpose: Very fast Monte Carlo (MC) simulations of proton transport have been implemented recently on GPUs. However, these usually use simplified models for non-elastic (NE) proton-nucleus interactions. Our primary goal is to build a GPU-based proton transport MC with detailed modeling of elastic and NE collisions. Methods: Using CUDA, we implemented GPU kernels for these tasks: (1) Simulation of spots from our scanning nozzle configurations, (2) Proton propagation through CT geometry, considering nuclear elastic scattering, multiple scattering, and energy loss straggling, (3) Modeling of the intranuclear cascade stage of NE interactions, (4) Nuclear evaporation simulation, and (5) Statistical error estimates on the dose. To validate our MC, we performed: (1) Secondary particle yield calculations in NE collisions, (2) Dose calculations in homogeneous phantoms, (3) Re-calculations of head and neck plans from a commercial treatment planning system (TPS), and compared with Geant4.9.6p2/TOPAS. Results: Yields, en...

  7. A comparison of electron transport coefficient predictions using spherical harmonic and Monte Carlo methods

    International Nuclear Information System (INIS)

    The electron drift velocity W, and the first Townsend ionization coefficient, α, are calculated for nitrogen, over the range 7000 is the electric field to pressure ratio. The pressure P0 is reduced to 00C. The spherical harmonic expansion calculation predicts α values which are 50-100% larger than those predicted by the Monte Carlo calculation. The predicted drift velocities agree to within 10-20%. (Auth.)

  8. Collocation method for the solution of the neutron transport equation with both symmetric and asymmetric scattering

    Energy Technology Data Exchange (ETDEWEB)

    Morel, J.E.

    1981-01-01

    A collocation method is developed for the solution of the one-dimensional neutron transport equation in slab geometry with both symmetric and polarly asymmetric scattering. For the symmetric scattering case, it is found that the collocation method offers a combination of some of the best characteristics of the finite-element and discrete-ordinates methods. For the asymmetric scattering case, it is found that the computational cost of cross-section data processing under the collocation approach can be significantly less than that associated with the discrete-ordinates approach. A general diffusion equation treating both symmetric and asymmetric scattering is developed and used in a synthetic acceleration algorithm to accelerate the iterative convergence of collocation solutions. It is shown that a certain type of asymmetric scattering can radically alter the asymptotic behavior of the transport solution and is mathematically equivalent within the diffusion approximation to particle transport under the influence of an electric field. The method is easily extended to other geometries and higher dimensions. Applications exist in the areas of neutron transport with highly anisotropic scattering (such as that associated with hydrogenous media), charged-particle transport, and particle transport in controlled-fusion plasmas. 23 figures, 6 tables.

  9. Overview of the MCU Monte Carlo software package

    International Nuclear Information System (INIS)

    Highlights: • MCU is the Monte Carlo code for particle transport in 3D systems with depletion. • Criticality and fixed source problems are solved using pure point-wise approximation. • MCU is parallelized with MPI in three different modes. • MCU has coolant, fuel and xenon feedback for VVER calculations. • MCU is verified for reactors with thermal, intermediate and fast neutron spectrum. - Abstract: MCU (Monte Carlo Universal) is a project on development and practical use of a universal computer code for simulation of particle transport (neutrons, photons, electrons, positrons) in three-dimensional systems by means of the Monte Carlo method. This paper provides the information on the current state of the project. The developed libraries of constants are briefly described, and the potentialities of the MCU-5 package modules and the executable codes compiled from them are characterized. Examples of important problems of reactor physics solved with the code are presented

  10. A new paradigm for whole core neutron transport without homogenization

    International Nuclear Information System (INIS)

    A new paradigm is introduced which allows the performance of whole core transport calculations without lattice homogenization. Quasi-reflected interface conditions are formulated to partially decouple periodic lattice effects from the pin-cell to pin-cell flux variation in the finite sub-element form of the variational nodal code VARIANT. With fuel-coolant homogenization eliminated, the interface variables that couple pin-cell sized nodes are divided into low-order and high-order spherical harmonic terms. Reflected interface conditions are subsequently applied to the high-order terms to remove them from the system of unknowns. Combined with an integral transport treatment within the node, the new approach dramatically reduces both the formation time and the size of the response matrices and leads to sharply reduced memory and CPU requirements. The method is applied to the two-dimensional C5-G7 problem, an OECD/NEA PWR benchmark containing MOX and UO2 fuel assemblies. Results indicate the new approach results in very little loss of accuracy relative to the corresponding full spherical harmonics expansions while reducing CPU times by well over an order of magnitude. (authors)

  11. Monte Carlo studies of accelerator driven systems: energy and spatial distribution of neutrons in multiplying and non-multiplying media

    International Nuclear Information System (INIS)

    The LAHET code system is used to study the behaviour of the spallation neutrons resulting from the interaction of 2.5 GeV/c protons with a massive lead target within a large (∼32 m3) lead and graphite moderating environments. The spatial and energy distribution of the neutrons with presence and absence of a fissile material in Accelerator Driven Systems (ADS) are investigated. It is shown that the energy spectra of the neutrons in graphite and lead moderators are very different and such difference is expected to result in noticeable differences in the nuclear waste transmutation abilities of the ADSs that use graphite and lead for neutron moderation and storage

  12. Monte Carlo simulation and Boltzmann equation analysis of non-conservative positron transport in H{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Bankovic, A., E-mail: ana.bankovic@gmail.com [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia); Dujko, S. [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia); Centrum Wiskunde and Informatica (CWI), P.O. Box 94079, 1090 GB Amsterdam (Netherlands); ARC Centre for Antimatter-Matter Studies, School of Engineering and Physical Sciences, James Cook University, Townsville, QLD 4810 (Australia); White, R.D. [ARC Centre for Antimatter-Matter Studies, School of Engineering and Physical Sciences, James Cook University, Townsville, QLD 4810 (Australia); Buckman, S.J. [ARC Centre for Antimatter-Matter Studies, Australian National University, Canberra, ACT 0200 (Australia); Petrovic, Z.Lj. [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia)

    2012-05-15

    This work reports on a new series of calculations of positron transport properties in molecular hydrogen under the influence of spatially homogeneous electric field. Calculations are performed using a Monte Carlo simulation technique and multi term theory for solving the Boltzmann equation. Values and general trends of the mean energy, drift velocity and diffusion coefficients as a function of the reduced electric field E/n{sub 0} are reported here. Emphasis is placed on the explicit and implicit effects of positronium (Ps) formation on the drift velocity and diffusion coefficients. Two important phenomena arise; first, for certain regions of E/n{sub 0} the bulk and flux components of the drift velocity and longitudinal diffusion coefficient are markedly different, both qualitatively and quantitatively. Second, and contrary to previous experience in electron swarm physics, there is negative differential conductivity (NDC) effect in the bulk drift velocity component with no indication of any NDC for the flux component. In order to understand this atypical manifestation of the drift and diffusion of positrons in H{sub 2} under the influence of electric field, the spatially dependent positron transport properties such as number of positrons, average energy and velocity and spatially resolved rate for Ps formation are calculated using a Monte Carlo simulation technique. The spatial variation of the positron average energy and extreme skewing of the spatial profile of positron swarm are shown to play a central role in understanding the phenomena.

  13. Ant colony algorithm implementation in electron and photon Monte Carlo transport: Application to the commissioning of radiosurgery photon beams

    International Nuclear Information System (INIS)

    Purpose: In this work, the authors describe an approach which has been developed to drive the application of different variance-reduction techniques to the Monte Carlo simulation of photon and electron transport in clinical accelerators. Methods: The new approach considers the following techniques: Russian roulette, splitting, a modified version of the directional bremsstrahlung splitting, and the azimuthal particle redistribution. Their application is controlled by an ant colony algorithm based on an importance map. Results: The procedure has been applied to radiosurgery beams. Specifically, the authors have calculated depth-dose profiles, off-axis ratios, and output factors, quantities usually considered in the commissioning of these beams. The agreement between Monte Carlo results and the corresponding measurements is within ∼3%/0.3 mm for the central axis percentage depth dose and the dose profiles. The importance map generated in the calculation can be used to discuss simulation details in the different parts of the geometry in a simple way. The simulation CPU times are comparable to those needed within other approaches common in this field. Conclusions: The new approach is competitive with those previously used in this kind of problems (PSF generation or source models) and has some practical advantages that make it to be a good tool to simulate the radiation transport in problems where the quantities of interest are difficult to obtain because of low statistics.

  14. A multi-agent quantum Monte Carlo model for charge transport: Application to organic field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Thilo; Jäger, Christof M. [Department of Chemistry and Pharmacy, Computer-Chemistry-Center and Interdisciplinary Center for Molecular Materials, Friedrich-Alexander-Universität Erlangen-Nürnberg, Nägelsbachstrasse 25, 91052 Erlangen (Germany); Jordan, Meredith J. T. [School of Chemistry, University of Sydney, Sydney, NSW 2006 (Australia); Clark, Timothy, E-mail: tim.clark@fau.de [Department of Chemistry and Pharmacy, Computer-Chemistry-Center and Interdisciplinary Center for Molecular Materials, Friedrich-Alexander-Universität Erlangen-Nürnberg, Nägelsbachstrasse 25, 91052 Erlangen (Germany); Centre for Molecular Design, University of Portsmouth, Portsmouth PO1 2DY (United Kingdom)

    2015-07-28

    We have developed a multi-agent quantum Monte Carlo model to describe the spatial dynamics of multiple majority charge carriers during conduction of electric current in the channel of organic field-effect transistors. The charge carriers are treated by a neglect of diatomic differential overlap Hamiltonian using a lattice of hydrogen-like basis functions. The local ionization energy and local electron affinity defined previously map the bulk structure of the transistor channel to external potentials for the simulations of electron- and hole-conduction, respectively. The model is designed without a specific charge-transport mechanism like hopping- or band-transport in mind and does not arbitrarily localize charge. An electrode model allows dynamic injection and depletion of charge carriers according to source-drain voltage. The field-effect is modeled by using the source-gate voltage in a Metropolis-like acceptance criterion. Although the current cannot be calculated because the simulations have no time axis, using the number of Monte Carlo moves as pseudo-time gives results that resemble experimental I/V curves.

  15. Ant colony algorithm implementation in electron and photon Monte Carlo transport: Application to the commissioning of radiosurgery photon beams

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Pareja, S.; Galan, P.; Manzano, F.; Brualla, L.; Lallena, A. M. [Servicio de Radiofisica Hospitalaria, Hospital Regional Universitario ' ' Carlos Haya' ' , Avda. Carlos Haya s/n, E-29010 Malaga (Spain); Unidad de Radiofisica Hospitalaria, Hospital Xanit Internacional, Avda. de los Argonautas s/n, E-29630 Benalmadena (Malaga) (Spain); NCTeam, Strahlenklinik, Universitaetsklinikum Essen, Hufelandstr. 55, D-45122 Essen (Germany); Departamento de Fisica Atomica, Molecular y Nuclear, Universidad de Granada, E-18071 Granada (Spain)

    2010-07-15

    Purpose: In this work, the authors describe an approach which has been developed to drive the application of different variance-reduction techniques to the Monte Carlo simulation of photon and electron transport in clinical accelerators. Methods: The new approach considers the following techniques: Russian roulette, splitting, a modified version of the directional bremsstrahlung splitting, and the azimuthal particle redistribution. Their application is controlled by an ant colony algorithm based on an importance map. Results: The procedure has been applied to radiosurgery beams. Specifically, the authors have calculated depth-dose profiles, off-axis ratios, and output factors, quantities usually considered in the commissioning of these beams. The agreement between Monte Carlo results and the corresponding measurements is within {approx}3%/0.3 mm for the central axis percentage depth dose and the dose profiles. The importance map generated in the calculation can be used to discuss simulation details in the different parts of the geometry in a simple way. The simulation CPU times are comparable to those needed within other approaches common in this field. Conclusions: The new approach is competitive with those previously used in this kind of problems (PSF generation or source models) and has some practical advantages that make it to be a good tool to simulate the radiation transport in problems where the quantities of interest are difficult to obtain because of low statistics.

  16. A multi-agent quantum Monte Carlo model for charge transport: Application to organic field-effect transistors

    International Nuclear Information System (INIS)

    We have developed a multi-agent quantum Monte Carlo model to describe the spatial dynamics of multiple majority charge carriers during conduction of electric current in the channel of organic field-effect transistors. The charge carriers are treated by a neglect of diatomic differential overlap Hamiltonian using a lattice of hydrogen-like basis functions. The local ionization energy and local electron affinity defined previously map the bulk structure of the transistor channel to external potentials for the simulations of electron- and hole-conduction, respectively. The model is designed without a specific charge-transport mechanism like hopping- or band-transport in mind and does not arbitrarily localize charge. An electrode model allows dynamic injection and depletion of charge carriers according to source-drain voltage. The field-effect is modeled by using the source-gate voltage in a Metropolis-like acceptance criterion. Although the current cannot be calculated because the simulations have no time axis, using the number of Monte Carlo moves as pseudo-time gives results that resemble experimental I/V curves

  17. Monte-Carlo Simulations of Radiation-Induced Activation in a Fast-Neutron and Gamma- Based Cargo Inspection System

    OpenAIRE

    Bromberger, B.; Bar, D.; Brandis, M.; Dangendorf, V.; Goldberg, M B; Kaufmann, F.; Mor, I.; Nolte, R.; SCHMIEDEL M.; Tittelmeier, K.; Vartsky, D.; H. Wershofen

    2012-01-01

    An air cargo inspection system combining two nuclear reaction based techniques, namely Fast-Neutron Resonance Radiography and Dual-Discrete-Energy Gamma Radiography is currently being developed. This system is expected to allow detection of standard and improvised explosives as well as special nuclear materials. An important aspect for the applicability of nuclear techniques in an airport inspection facility is the inventory and lifetimes of radioactive isotopes produced by the neutron and ga...

  18. Numerical evaluation of the light transport properties of alternative He-3 neutron detectors using ceramic scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Ohzu, A., E-mail: ohzu.akira@jaea.go.jp [Nuclear Science and Engineering Center, Japan Atomic Energy Agency, Tokai, Naka, Ibaraki 319-1195 (Japan); Takase, M.; Haruyama, M.; Kurata, N.; Kobayashi, N.; Kureta, M. [Nuclear Science and Engineering Center, Japan Atomic Energy Agency, Tokai, Naka, Ibaraki 319-1195 (Japan); Nakamura, T.; Toh, K.; Sakasai, K.; Suzuki, H.; Soyama, K. [J-PARC, Japan Atomic Energy Agency, Tokai, Naka, Ibaraki 319-1195 (Japan); Seya, M. [Integrated Support Center for Nuclear Nonproliferation and Nuclear Security, Japan Atomic Energy Agency, Tokai, Naka, Ibaraki 319-1195 (Japan)

    2015-10-21

    The light transport properties of scintillator light inside alternative He-3 neutron detectors using scintillator sheets have been investigated by a ray-tracing simulation code. The detector consists of a light-reflecting tube, a thin rectangular ceramic scintillator sheet laminated on a glass plate, and two photo-multiplier tubes (PMTs) mounted at both ends of the detector tube. The flashes of light induced on the surface of the scintillator sheet via nuclear interaction between the scintillator and neutrons are detected by the two PMTs. The light output at both ends of various detectors in which the scintillator sheets are installed with several different arrangements were examined and evaluated in comparison with experimental results. The results derived from the simulation reveal that the light transport property is strongly dependent on the arrangement of the scintillator sheet inside the tube and the shape of the tube.

  19. Neutron transport solver parallelization using a Domain Decomposition method

    International Nuclear Information System (INIS)

    A domain decomposition (DD) method is investigated for the parallel solution of the second-order even-parity form of the time-independent Boltzmann transport equation. The spatial discretization is performed using finite elements, and the angular discretization using spherical harmonic expansions (PN method). The main idea developed here is due to P.L. Lions. It consists in having sub-domains exchanging not only interface point flux values, but also interface flux 'derivative' values. (The word 'derivative' is here used with quotes, because in the case considered here, it in fact consists in the Ω.∇ operator, with Ω the angular variable vector and ∇ the spatial gradient operator.) A parameter α is introduced, as proportionality coefficient between point flux and 'derivative' values. This parameter can be tuned - so far heuristically - to optimize the method. (authors)

  20. Deterministic methods to solve the differential transport equation in neutronic

    International Nuclear Information System (INIS)

    We present a synthesis of the methods used to solve the integro-differential form of the transport equation. This form is used above all to achieve whole core calculations in 2 and 3D. First, we discretize the equation in energy and it leads us to an one group energy equation. For each of these groups, the scope of the calculation is so big that we have to calculate our solution on homogenized cells. On this homogenized medium, we describe different angular and spatial discretizations with acceleration methods. Finally we select some promising schemes to test: - SN Linear Nodal method with a Diffusion Synthetic Acceleration method; - Variational Nodal Method. These methods could be compared with more classical ones. To say, finite element or finite difference methods. (author). 65 refs., 3 annexes

  1. New contributions to neutron stochastic transport theory in the time and in the frequency domain

    International Nuclear Information System (INIS)

    The authors generalize the stochastic transport theory of Pal and Munoz-Cobo and Perez methodology, to include the delayed neutron effects. They apply this theory to interpret several experiments measuring the cross power spectral density G12(W), G13(W), G23(W) of three detectors 1, 2 and 3, located in and out of a tank containing a UO2F2 solution in water. (Auth.)

  2. Instrumentation development for magneto-transport and neutron scattering measurements at high pressure and low temperature

    OpenAIRE

    Wang, Weiwei

    2013-01-01

    High pressure, high magnetic field and low temperature techniques are required to investigate magnetic transitions and quantum critical behaviour in different ferromagnetic materials to elucidate how novel forms of superconductivity and other new states are brought about. In this project, several instruments for magneto-transport and neutron scattering measurements have been designed and built. They include inserts for a dilution refrigerator and pressure cells for resistivity,...

  3. Normal and adjoint integral and integrodifferential neutron transport equations. Pt. 2

    International Nuclear Information System (INIS)

    Using the simplifying hypotheses of the integrodifferential Boltzmann equations of neutron transport, given in JEN 334 report, several integral equations, and theirs adjoint ones, are obtained. Relations between the different normal and adjoint eigenfunctions are established and, in particular, proceeding from the integrodifferential Boltzmann equation it's found out the relation between the solutions of the adjoint equation of its integral one, and the solutions of the integral equation of its adjoint one (author)

  4. Multilevel Monte Carlo methods using ensemble level mixed MsFEM for two-phase flow and transport simulations

    KAUST Repository

    Efendiev, Yalchin R.

    2013-08-21

    In this paper, we propose multilevel Monte Carlo (MLMC) methods that use ensemble level mixed multiscale methods in the simulations of multiphase flow and transport. The contribution of this paper is twofold: (1) a design of ensemble level mixed multiscale finite element methods and (2) a novel use of mixed multiscale finite element methods within multilevel Monte Carlo techniques to speed up the computations. The main idea of ensemble level multiscale methods is to construct local multiscale basis functions that can be used for any member of the ensemble. In this paper, we consider two ensemble level mixed multiscale finite element methods: (1) the no-local-solve-online ensemble level method (NLSO); and (2) the local-solve-online ensemble level method (LSO). The first approach was proposed in Aarnes and Efendiev (SIAM J. Sci. Comput. 30(5):2319-2339, 2008) while the second approach is new. Both mixed multiscale methods use a number of snapshots of the permeability media in generating multiscale basis functions. As a result, in the off-line stage, we construct multiple basis functions for each coarse region where basis functions correspond to different realizations. In the no-local-solve-online ensemble level method, one uses the whole set of precomputed basis functions to approximate the solution for an arbitrary realization. In the local-solve-online ensemble level method, one uses the precomputed functions to construct a multiscale basis for a particular realization. With this basis, the solution corresponding to this particular realization is approximated in LSO mixed multiscale finite element method (MsFEM). In both approaches, the accuracy of the method is related to the number of snapshots computed based on different realizations that one uses to precompute a multiscale basis. In this paper, ensemble level multiscale methods are used in multilevel Monte Carlo methods (Giles 2008a, Oper.Res. 56(3):607-617, b). In multilevel Monte Carlo methods, more accurate

  5. Theoretical simulation of neutron albedo experiment

    International Nuclear Information System (INIS)

    The purpose of neutron albedo experiment is to check and scale the programs, parameters and methods used in engineering design. Monte-Carlo particle transport code is used to simulate the experiment, and the neutron activation rate and albedo coefficient of each detecting point on iron spherical shell's outer surface were obtained. It is proved that the theoretical results are in good agreement with the experiment data within the range of data's uncertainty. (authors)

  6. Monte Carlo simulation of the neutron porosity logging using D-D neutron generator%D-D中子源孔隙度测井的蒙特卡洛模拟

    Institute of Scientific and Technical Information of China (English)

    严岩; 李炳营; 郑世平; 闫永宏; 杨尧; 姚泽恩; 刘炯

    2012-01-01

    The D-D neutron source model was developed according to the neutron energy spectrum and angular distribution of D-D reaction and the standard calibration well model was developed too. The D-D neutron transports in the well model were simulated using the MCNP code. The distributions of relative thermal neutron flux in axis and the relative porosity sensitivity for different source spacing were presented. The results show that the location of zero porosity sensitivity was about 17 cm, and the detector should be located at 25~60 cm space. According to the neutron energy spectrum and angular distribution data, the models of D-T and Am-Be neutron source were also developed. The near-to-far count ratio R and the porosity sensitivities S of the compensated neutron porosity logging were investigated respectively for D-T, D-D and Am-Be neutron sources using the MCNP code, and the results show that the D-D neutron source exhibited a higher sensitivity and higher neutron efficiency in contrast with D-T and Am-Be neutron sources.%根据D-D反应中子的能谱和角分布数据,建立了D-D中子源模型.根据标准刻度井数据,建立了井模型.采用MCNP程序模拟了D-D中子在井中的输运,给出了热中子相对通量沿轴线的分布和孔隙度探测灵敏度随源距的变化,结果显示对D-D中子源,孔隙度测量零灵敏约在17 cm附近,探测器的适宜布置区间为25~60 cm.根据D-T反应中子和Am-Be中子源的能谱及角分布数据,建立了其中子源模型,通过MCNP模拟,研究了补偿法孔隙度测井时近远探测器中的热中子计数比值R及测量灵敏度S随孔隙度的变化,并与D-D中子源的模拟结果进行了比较,结果显示D-D源有更高的测量灵敏度和更高的中子利用率.

  7. Development of a New Monte Carlo reactor physics code

    OpenAIRE

    Leppänen, Jaakko

    2007-01-01

    Monte Carlo neutron transport codes are widely used in various reactor physics applications, traditionally related to criticality safety analyses, radiation shielding problems, detector modelling and validation of deterministic transport codes. The main advantage of the method is the capability to model geometry and interaction physics without major approximations. The disadvantage is that the modelling of complicated systems is very computing-intensive, which restricts the applications to so...

  8. ITS version 5.0 : the integrated TIGER series of coupled electron/photon Monte Carlo transport codes.

    Energy Technology Data Exchange (ETDEWEB)

    Franke, Brian Claude; Kensek, Ronald Patrick; Laub, Thomas William

    2004-06-01

    ITS is a powerful and user-friendly software package permitting state of the art Monte Carlo solution of linear time-independent couple electron/photon radiation transport problems, with or without the presence of macroscopic electric and magnetic fields of arbitrary spatial dependence. Our goal has been to simultaneously maximize operational simplicity and physical accuracy. Through a set of preprocessor directives, the user selects one of the many ITS codes. The ease with which the makefile system is applied combines with an input scheme based on order-independent descriptive keywords that makes maximum use of defaults and internal error checking to provide experimentalists and theorists alike with a method for the routine but rigorous solution of sophisticated radiation transport problems. Physical rigor is provided by employing accurate cross sections, sampling distributions, and physical models for describing the production and transport of the electron/photon cascade from 1.0 GeV down to 1.0 keV. The availability of source code permits the more sophisticated user to tailor the codes to specific applications and to extend the capabilities of the codes to more complex applications. Version 5.0, the latest version of ITS, contains (1) improvements to the ITS 3.0 continuous-energy codes, (2)multigroup codes with adjoint transport capabilities, and (3) parallel implementations of all ITS codes. Moreover the general user friendliness of the software has been enhanced through increased internal error checking and improved code portability.

  9. Monte-Carlo Simulations of Radiation-Induced Activation in a Fast-Neutron and Gamma- Based Cargo Inspection System

    CERN Document Server

    Bromberger, B; Brandis, M; Dangendorf, V; Goldberg, M B; Kaufmann, F; Mor, I; Nolte, R; Schmiedel, M; Tittelmeier, K; Vartsky, D; Wershofen, H

    2012-01-01

    An air cargo inspection system combining two nuclear reaction based techniques, namely Fast-Neutron Resonance Radiography and Dual-Discrete-Energy Gamma Radiography is currently being developed. This system is expected to allow detection of standard and improvised explosives as well as special nuclear materials. An important aspect for the applicability of nuclear techniques in an airport inspection facility is the inventory and lifetimes of radioactive isotopes produced by the neutron and gamma radiation inside the cargo, as well as the dose delivered by these isotopes to people in contact with the cargo during and following the interrogation procedure. Using MCNPX and CINDER90 we have calculated the activation levels for several typical inspection scenarios. One example is the activation of various metal samples embedded in a cotton-filled container. To validate the simulation results, a benchmark experiment was performed, in which metal samples were activated by fast-neutrons in a water-filled glass jar. T...

  10. Atomic structure of glassy Mg60Cu30Y10 investigated with EXAFS, x-ray and neutron diffraction, and reverse Monte Carlo simulations

    DEFF Research Database (Denmark)

    Jovari, P.; Saksl, K.; Pryds, Nini;

    2007-01-01

    Short range order of amorphous Mg60Cu30Y10 was investigated by x-ray and neutron diffraction, Cu and Y K-edge x-ray absorption fine structure measurements, and the reverse Monte Carlo simulation technique. We found that Mg-Mg and Mg-Cu nearest neighbor distances are very similar to values found in...... studied by differential scanning calorimetry and in situ x-ray powder diffraction. The alloy shows a glass transition and three crystallization events, the first and dominant one at 456 K corresponding to eutectic crystallization of at least three phases: Mg2Cu and most likely cubic MgY and CuMgY....

  11. Monte Carlo simulation of prompt gamma-ray spectra from depleted uranium under D-T neutron irradiation and electron recoil spectra in a liquid scintillator detector

    CERN Document Server

    Qin, Jianguo; Liu, Rong; Zhu, Tonghua; Zhang, Xinwei; Ye, Bangjiao

    2015-01-01

    To overcome the problem of inefficient computing time and unreliable results in MCNP5 calculation, a two-step method is adopted to calculate the energy deposition of prompt gamma-rays in detectors for depleted uranium spherical shells under D-T neutrons irradiation. In the first step, the gamma-ray spectrum for energy below 7 MeV is calculated by MCNP5 code; secondly, the electron recoil spectrum in a BC501A liquid scintillator detector is simulated based on EGSnrc Monte Carlo Code with the gamma-ray spectrum from the first step as input. The comparison of calculated results with experimental ones shows that the simulations agree well with experiment in the energy region 0.4-3 MeV for the prompt gamma-ray spectrum and below 4 MeVee for the electron recoil spectrum. The reliability of the two-step method in this work is validated.

  12. Monte Carlo simulations and benchmark measurements on the response of TE(TE) and Mg(Ar) ionization chambers in photon, electron and neutron beams

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Yi-Chun [Health Physics Division, Institute of Nuclear Energy Research, Taoyuan County, Taiwan (China); Huang, Tseng-Te, E-mail: huangtt@iner.gov.tw [Health Physics Division, Institute of Nuclear Energy Research, Taoyuan County, Taiwan (China); Liu, Yuan-Hao [Nuclear Science and Technology Development Center, National Tsing Hua University, Hsinchu City, Taiwan (China); Chen, Wei-Lin [Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu City, Taiwan (China); Chen, Yen-Fu [Atomic Energy Council, New Taipei City, Taiwan (China); Wu, Shu-Wei [Dept. of Biomedical Engineering and Environmental Sciences, National Tsing Hua University, Hsinchu, Taiwan (China); Nievaart, Sander [Institute for Energy, Joint Research Centre, European Commission, Petten (Netherlands); Jiang, Shiang-Huei [Dept. of Engineering and System Science, National Tsing Hua University, Hsinchu, Taiwan (China)

    2015-06-01

    The paired ionization chambers (ICs) technique is commonly employed to determine neutron and photon doses in radiology or radiotherapy neutron beams, where neutron dose shows very strong dependence on the accuracy of accompanying high energy photon dose. During the dose derivation, it is an important issue to evaluate the photon and electron response functions of two commercially available ionization chambers, denoted as TE(TE) and Mg(Ar), used in our reactor based epithermal neutron beam. Nowadays, most perturbation corrections for accurate dose determination and many treatment planning systems are based on the Monte Carlo technique. We used general purposed Monte Carlo codes, MCNP5, EGSnrc, FLUKA or GEANT4 for benchmark verifications among them and carefully measured values for a precise estimation of chamber current from absorbed dose rate of cavity gas. Also, energy dependent response functions of two chambers were calculated in a parallel beam with mono-energies from 20 keV to 20 MeV photons and electrons by using the optimal simple spherical and detailed IC models. The measurements were performed in the well-defined (a) four primary M-80, M-100, M120 and M150 X-ray calibration fields, (b) primary {sup 60}Co calibration beam, (c) 6 MV and 10 MV photon, (d) 6 MeV and 18 MeV electron LINACs in hospital and (e) BNCT clinical trials neutron beam. For the TE(TE) chamber, all codes were almost identical over the whole photon energy range. In the Mg(Ar) chamber, MCNP5 showed lower response than other codes for photon energy region below 0.1 MeV and presented similar response above 0.2 MeV (agreed within 5% in the simple spherical model). With the increase of electron energy, the response difference between MCNP5 and other codes became larger in both chambers. Compared with the measured currents, MCNP5 had the difference from the measurement data within 5% for the {sup 60}Co, 6 MV, 10 MV, 6 MeV and 18 MeV LINACs beams. But for the Mg(Ar) chamber, the derivations

  13. Criticality prompt gamma and neutron dose equations validated by Monte Carlo analyses and compared to known criticality accident doses

    Science.gov (United States)

    Hochhalter, Eugene

    The United States (US) Department of Energy [DOE] and the Nuclear Regulatory Commission [NRC] have provided the nuclear industry with requirements, goals, and objectives for the preparation of safety analysis and the finalization of that safety analysis in the form of a documented safety analysis (DSA) and technical safety requirements (TSRs). The deterministic guidance provided by the NRC in Regulatory Guide (RG) 3.33 for calculating the prompt gamma and neutron doses from a criticality has a number of potential issues associated with the semi-empirical equations, which make these equations potentially out dated. The NRC guidance for estimating the prompt gamma and neutron doses to a facility worker due to an accidental criticality was withdrawn without newer deterministic guidance being issued. This research project determined the original basis for the RG prompt gamma and neutron equations, evaluated the potential issues associated with the RG 3.33 prompt gamma and neutron equations, and modified the RG 3.33 point source prompt gamma and neutron equations to calculate the doses for the selected set of criticality accidents. The criticality accidents addressed by this dissertation include: 1. U-235, Pu-239, and Pu-241 point source criticality, 2. U-235, Pu-239, and Pu-241 sphere source criticality, 3. Uranyl nitrate and plutonium nitrate solutions in a cylindrical process vessel and 4. Low level waste in 55-gallon and 30-gallon drums. The prompt gamma and neutron equation doses (RG 3.33/3.34/3.35) are compared to actual nuclear industry criticality accident worker doses to assess the conservatism of the RG equations. Finally, the RG 3.33 prompt gamma and neutron dose equations are compared to MCNP5 results to investigate consistency with respect to the modified prompt gamma and neutron dose equations and the representative dose estimates for each of the criticality configurations (point source, spherical source, and cylindrical source). Knowledge and accurate

  14. A stochastic transport theory of neutron and photon coupled fields neutron and photon counting statistics in nuclear assemblies

    International Nuclear Information System (INIS)

    The behavior of neutrons and gamma rays in a nuclear reactor or configuration of fissile material can be represented as a stochastic process. The observation of this stochastic process is usually achieved by measuring the fluctuations of the neutron and gamma ray population on the system. The general theory of the stochastic neutron field has been developed to a high degree. However, the theory of the stochastic nature of the gamma rays and neutrons couples the two processes. The generalized probability balances are developed from which the first and higher moments of the neutron and gamma rays fields are obtained. The paper also provides a description of the probability generating functions for both photon and neutron detectors that are the foundations for measurements of the fluctuations. The formalism developed in this paper for the representation of the statistical descriptors of the neutron-photon coupled field is applicable for many neutron noise analysis measurements

  15. Static properties of polystyrene in semidilute solutions: A comparison of Monte Carlo simulation and small-angle neutron scattering results

    DEFF Research Database (Denmark)

    Pedersen, J.S.; Schurtenberger, P.

    1999-01-01

    determined for the simulations as well as experimentally for polystyrene in d-toluene by small-angle neutron scattering (SANS), and excellent agreement is found. Interpolations of the MC scattering functions fit the SANS data in the full measured range of scattering vectors, demonstrating agreement almost...

  16. A Monte Carlo simulation to study a design of a gamma-ray detector for neutron resonance densitometry

    Science.gov (United States)

    Tsuchiya, H.; Harada, H.; Koizumi, M.; Kitatani, F.; Takamine, J.; Kureta, M.; Iimura, H.

    2013-11-01

    Neutron resonance densitometry (NRD) has been proposed to quantify nuclear materials in melted fuel (MF) that will be removed from the Fukushima Daiichi nuclear power plant. The problem is complex due to the expected presence of strong neutron absorbing impurities such as 10B and high radiation field that is mainly caused by 137Cs. To identify the impurities under the high radiation field, NRD is based on a combination of neutron resonance transmission analysis (NRTA) and neutron resonance capture analysis (NRCA). We investigated with Geant4 the performance of a gamma-ray detector for NRCA in NRD. The gamma-ray detector has a well shape, consisting of cylindrical and tube type LaBr3 scintillators. We show how it measures 478 keV gamma rays derived from 10B(n, αγ) reaction in MF under a high 137Cs-radiation environment. It was found that the gamma-ray detector was able to well suppress the Compton edge of 662-keV gamma rays of 137Cs and had a high peak-to-Compton continuum ratio, by using the tube type scintillator as a back-catcher detector. Then, we demonstrate that with this ability, detection of 478-keV gamma rays from 10B is accomplished in realistic measuring time.

  17. Monte Carlo Simulation of Light Transport in Five-Layered Skin Tissue

    Institute of Scientific and Technical Information of China (English)

    XUE Ling-Ling; ZHANG Chun-Ping; WANG Xin-Yu; ZHU Ming-Yao; ZHANG Lian-Shun; CHI Rong-Hua; ZHANG Jian-Dong; ZHANG Guang-Yin

    2000-01-01

    The light propagation and distribution in skin tissue is studied by using Monte Carlo technique. The radially resolved diffuse reflectance R and transmittance T vs radius r, angularly resolved R and Tvs the exiting angle of the photon, absorption energy density A and internal fiuence F vs r and z are simulated. Our results reveal that the light distribution for Gaussian beam is more centralized and its change is more rapid than those of circularly flat beam under the same incident energy and radius, no matter what R and T or A and F are. In addition,except that R(r) for circularly flat beam needs to be fitted by 15-order curve, the others can be fitted by 5-order or 6-order curve.

  18. Monte Carlo simulation on electron transport in Si sub 1 sub - sub y C sub y alloy layers

    CERN Document Server

    Ihm, S H; Lee, C H; Lee, H J; Kim, J Y; Chun, S K

    1999-01-01

    We investigated electron transport in strained Si sub 1 sub - sub y C sub y alloy layers grown on Si(100) substrates using the Monte Carlo simulation. The electron mobility higher than that of bulk Si over a wide range of temperatures from 40 K to 300 K is mainly attributed to the valley splitting induced by the tensile strain in the Si sub 1 sub - sub y C sub y layer. For lower temperatures less than 100 K the mobility increases sharply depending on the carbon fraction up to about 0.6%. Beyond the fraction, however, it keeps almost constant regardless of increasing the carbon fraction. On the other hand, we observe a monotonic mobility increase with increasing the carbon for a higher temperature regime.

  19. Observing gas and dust in simulations of star formation with Monte Carlo radiation transport on Voronoi meshes

    CERN Document Server

    Hubber, D A; Dale, J

    2015-01-01

    Ionising feedback from massive stars dramatically affects the interstellar medium local to star forming regions. Numerical simulations are now starting to include enough complexity to produce morphologies and gas properties that are not too dissimilar from observations. The comparison between the density fields produced by hydrodynamical simulations and observations at given wavelengths relies however on photoionisation/chemistry and radiative transfer calculations. We present here an implementation of Monte Carlo radiation transport through a Voronoi tessellation in the photoionisation and dust radiative transfer code MOCASSIN. We show for the first time a synthetic spectrum and synthetic emission line maps of an hydrodynamical simulation of a molecular cloud affected by massive stellar feedback. We show that the approach on which previous work is based, which remapped hydrodynamical density fields onto Cartesian grids before performing radiative transfer/photoionisation calculations, results in significant ...

  20. Monte-Carlo simulations of neutron-induced activation in a Fast-Neutron and Gamma-Based Cargo Inspection System

    Science.gov (United States)

    Bromberger, B.; Bar, D.; Brandis, M.; Dangendorf, V.; Goldberg, M. B.; Kaufmann, F.; Mor, I.; Nolte, R.; Schmiedel, M.; Tittelmeier, K.; Vartsky, D.; Wershofen, H.

    2012-03-01

    An air cargo inspection system combining two nuclear reaction based techniques, namely Fast-Neutron Resonance Radiography and Dual-Discrete-Energy Gamma Radiography is currently being developed. This system is expected to allow detection of standard and improvised explosives as well as special nuclear materials. An important aspect for the applicability of nuclear techniques in an airport inspection facility is the inventory and lifetimes of radioactive isotopes produced by the neutron radiation inside the cargo, as well as the dose delivered by these isotopes to people in contact with the cargo during and following the interrogation procedure. Using MCNPX and CINDER90 we have calculated the activation levels for several typical inspection scenarios. One example is the activation of various metal samples embedded in a cotton-filled container. To validate the simulation results, a benchmark experiment was performed, in which metal samples were activated by fast-neutrons in a water-filled glass jar. The induced activity was determined by analyzing the gamma spectra. Based on the calculated radioactive inventory in the container, the dose levels due to the induced gamma radiation were calculated at several distances from the container and in relevant time windows after the irradiation, in order to evaluate the radiation exposure of the cargo handling staff, air crew and passengers during flight. The possibility of remanent long-lived radioactive inventory after cargo is delivered to the client is also of concern and was evaluated.