WorldWideScience

Sample records for bromine chlorides

  1. A comparison of the virucidal properties of chlorine, chlorine dioxide, bromine chloride and iodine.

    OpenAIRE

    Taylor, G. R.; Butler, M.

    1982-01-01

    Chlorine dioxide, bromine chloride and iodine were compared with chlorine as virucidal agents. Under optimal conditions all disinfectants were effective at low concentrations, but each disinfectant responded differently to acidity and alkalinity. Disinfection by chlorine was impaired by the presence of ammonia, but the other disinfectants retained much of their potency. Disinfection of poliovirus by iodine resulted in structural changes in the virions as seen by electron micrroscopy, but the ...

  2. Effect of brominated furanones on the formation of biofilm by Escherichia coli on polyvinyl chloride materials.

    Science.gov (United States)

    Lianhua, Ye; Yunchao, Huang; Geng, Xu; Youquang, Zhou; Guangqiang, Zhao; Yujie, Lei

    2013-01-01

    To study the influence of brominated furanones on the biofilm (BF) formation by Escherichia coli (E. coli) on polyvinyl chloride (PVC) material, and to provide new ways of surface modification of materials to clinically prevent biomaterial centered infection. Three brominated furanones, dissolved in ethanol, furanone-1(3,4-dibromo-5-hydroxyl-furanone), furanone-2(4-bromo-5-(4-methoxypheny)-3-(methylamino)-furanone), and furanone-3(3,4-dibromo-5,5-dimethoxypheny-2(5H)-furanone) with representative chemical structure, were coated on the surfaces of separate PVC materials (1 × 1 cm), respectively. The surface-modified PVC materials were incubated with E. coli and for controls, 75 % ethanol-treated PVC materials were used. This treatment played as control group. The cultivation incubations were for 6, 12, 18, and 24 h. The thickness of bacterial BF and bacterial community quantity unit area on the PVC materials was determined by confocal laser scanning microscopy (CLSM), and the surface structure of bacterial BF formation was examined by scanning electron microscopy (SEM). The results of CLSM indicated the thickness of bacterial BF and bacterial community quantity unit area on PVC materials treated with furanone-3 were significantly lower than that of control at all time points (P 0.05). The results of SEM indicated that after 6 h incubation, the quantity of bacterial attachment to the surface of PVC material treated with furanone-3 was lower than the control group. By 18 h incubation there was completely formed BF structure on the surface of control PVC material. However, there was no significant BF formation on the surface of PVC material treated with furanone-3. The impact of different brominated furanones on SA biofilm formation on the surface of PVC materials are different, furanone-3 can inhibit E. coli biofilm formation on the surface of PVC material.

  3. Assessment of capacity loss in low-rate lithium/bromine chloride in thionyl chloride cells by microcalorimetry and long-term discharge

    Science.gov (United States)

    Takeuchi, E. S.; Meyer, S. M.; Holmes, C. F.

    1990-06-01

    Real-time discharge is one of the few reliable methods available for determining capacities of low-rate cells. The utilization of high energy density lithium batteries in low-rate implantable applications has increased the need for more time-efficient methods of predicting cell longevity since cells have been shown to last in excess of eight years. The relationship between heat dissipation and self-discharge of low-rate lithium/BCX (bromine chloride in thionyl chloride) cells was studied and allows prediction of cell life prior to the availability of real-time data. The method was verified by real-time cell discharge data and provided estimates of delivered capacity within 6 percent of the actual values.

  4. Use of carbon filaments in place of carbon black as the current collector of a lithium cell with a thionyl chloride bromine chloride catholyte

    Science.gov (United States)

    Frysz, Christine A.; Shui, Xiaoping; Chung, D. D. L.

    Submicron carbon filaments (ADNH, Applied Sciences Inc.) used in place of carbon black as porous reduction electrodes (i.e., current collectors) in plate and jellyroll configurations in carbon limited lithium batteries with the BCX (bromine chloride in thionyl chloride) catholyte gave a specific capacity (at 2 V cut-off) of up to 8700 mAh/g of carbon, compared with a value of up to 2900 mAh/g of carbon for carbon black. The high specific capacity for the filament electrode is partly due to the filaments' processability into sheets as thin as 0.2 mm with good porosity, acceptable mechanical properties and without binder, and partly due to the high catholyte absorptivity and high rate of catholyte absorption of the filament electrode. Use of solvent-cleansed filaments in place of as-received filaments in making electrodes increased the packing density, thus decreasing capacity per g of carbon. The BCX catholyte acted as a cleanser anyway, due to the thionyl chloride in it. The specific capacity per cm 3 of carbon and that per unit density of carbon were also increased by using carbon filaments in place of carbon black, provided that the filament electrode was not pressed after forming by slurry filtration. Though no binder was needed for the filament plate electrode, it was needed for the filament jellyroll electrode. The Teflon™ binder increased the tensile strength and modulus, but decreased the catholyte absorption and rate of absorption. The filament electrode exhibited 405 less volume electrical resistivity than the carbon black electrode, both without a binder.

  5. Bromination of Aromatic Compounds by Residual Bromide in Sodium Chloride Matrix Modifier Salt During Heated Headspace GC/MS Analysis

    Science.gov (United States)

    Analytical artifacts attributed to the bromination of toluene, xylenes, and trimethylbenzenes were found during the heated headspace gas chromatography/mass spectrometry (GC/MS) analysis of aqueous samples. The aqueous samples were produced from Fenton-like chemical oxidation rea...

  6. Bromine Safety

    Energy Technology Data Exchange (ETDEWEB)

    Meyers, B

    2001-04-09

    The production and handling in 1999 of about 200 million kilograms of bromine plus substantial derivatives thereof by Great Lakes Chemical Corp. and Albemarle Corporation in their southern Arkansas refineries gave OSHA Occupational Injury/Illness Rates (OIIR) in the range of 0.74 to 1.60 reportable OIIRs per 200,000 man hours. OIIRs for similar industries and a wide selection of other U.S. industries range from 1.6 to 23.9 in the most recent OSHA report. Occupational fatalities for the two companies in 1999 were zero compared to a range in the U.S.of zero for all computer manufacturing to 0.0445 percent for all of agriculture, forestry and fishing in the most recent OSHA report. These results show that bromine and its compounds can be considered as safe chemicals as a result of the bromine safety standards and practices at the two companies. The use of hydrobromic acid as an electrical energy storage medium in reversible PEM fuel cells is discussed. A study in 1979 of 20 megawatt halogen working fluid power plants by Oronzio de Nora Group found such energy to cost 2 to 2.5 times the prevailing base rate at that time. New conditions may reduce this relative cost. The energy storage aspect allows energy delivery at maximum demand times where the energy commands premium rates. The study also found marginal cost and performance advantages for hydrobromic acid over hydrochloric acid working fluid. Separate studies in the late 70s by General Electric also showed marginal performance advantages for hydrobromic acid.

  7. Bromination of Phenol

    Science.gov (United States)

    Talbot, Christopher

    2013-01-01

    This "Science note" examines the bromination of phenol, a reaction that is commonly taught at A-level and IB (International Baccalaureate) as an example of electrophilic substitution. Phenol undergoes bromination with bromine or bromine water at room temperature. A white precipitate of 2,4,6-tribromophenol is rapidly formed. This…

  8. Zinc-bromine battery development

    Science.gov (United States)

    Richards, Lew; Vanschalwijk, Walter; Albert, George; Tarjanyi, Mike; Leo, Anthony; Lott, Stephen

    1990-05-01

    This report describes development activities on the zinc-bromine battery system conducted by Energy Research Corporation (ERC). The project was a cost-shared program supported by the U.S. Department of Energy and managed through Sandia. The project began in September 1985 and ran through January 1990. The zinc-bromine battery has been identified as a promising alternative to conventional energy storage options for many applications. The low cost of the battery reactants and the potential for long life make the system an attractive candidate for bulk energy storage applications, such as utility load leveling. The battery stores energy by the electrolysis of an aqueous zinc bromide salt to zinc metal and dissolved bromine. Zinc is plated as a layer on the electrode surface while bromine is dissolved in the electrolyte and carried out of the stack. The bromine is then extracted from the electrolyte with an organic complexing agent in the positive electrolyte storage tank. On discharge the zinc and bromine are consumed, regenerating the zinc bromide salt.

  9. Synthesis of 1-Bromo-3-methoxy-4-propoxy-5-iodobenzene-A Novel Efficient Process for the Synthesis of Brominated Aromatic Compound

    Institute of Scientific and Technical Information of China (English)

    Hong Xin SHI; Hui LIN; Gérard MANDVILLE

    2004-01-01

    The reaction of aromatic carboxylic acid with oxalyl chloride gives rise to the corres- ponding acid chloride which without purification is treated with the sodium salt of mercapto- pyridine oxide in the presence of 2,2-azo-bisisobutyronitrile (AIBN), radical initiator to give a brominated aromatic compound. After etherification and oxidation, 5-iodovaniline was converted to trisubstituted benzene carboxylic acid which give 1-bromo-3-methoxy-4-propoxy-5-iodo- benzene by this new brominating process with a yield of 74 %.

  10. Enzymatic chlorination and bromination.

    Science.gov (United States)

    van Pée, Karl-Heinz

    2012-01-01

    Our knowledge about the enzymes catalyzing the incorporation of halide ions during the biosynthesis of halometabolites has increased tremendously during the last 15 years. Between 1960 and 1995, haloperoxidases were the only halogenating enzymes known. However, absolute proof for the connection of haloperoxidases to the biosynthesis of halometabolites is still missing. In 1997, FADH(2)-dependent halogenases were identified as the type of halogenating enzymes responsible for the incorporation of chloride and bromide atoms into aromatic and aliphatic compounds activated for electrophilic attack. FADH(2)-dependent halogenases are two-component systems consisting of a flavin reductase providing the FADH(2) required by the halogenase. Elucidation of the three-dimensional structure of FADH(2)-dependent halogenases led to the understanding of the reaction mechanism, which involves the formation of hypohalous acids. Unactivated carbon atoms were found to be halogenated by nonheme iron, α-ketoglutarate- and O(2)-dependent halogenases. The reaction mechanism of this type of halogenase was shown to involve the formation of a substrate radical. These two types of halogenating enzymes, together with the much less common fluorinases, are the major types of halogenating enzymes. However, the existence of other types of halogenating enzymes, yet not detected, cannot be completely ruled out. Here, we describe the detection, purification, characterization, and reaction mechanisms of flavin-dependent halogenases and of nonheme iron, α-ketoglutarate- and O(2)-dependent halogenases.

  11. Production of bromine-75, a new radionuclide for marking radiopharmaceuticals

    Energy Technology Data Exchange (ETDEWEB)

    Paans, A.M.J.; Wiegman, T.; Hoeve, W.; Vaalburg, W. (Rijksuniversiteit Groningen (Netherlands). Academisch Ziekenhuis)

    1982-01-01

    Bromine-75 is the most useful of all bromine isotopes for nuclear medicine. Its properties like half-life, nuclear reactions, production and chemical preparation, as well as the preparation of radiopharmaceuticals containing bromine-75 are presented.

  12. Systematic vibration thermodynamic properties of bromine

    Science.gov (United States)

    Liu, G. Y.; Sun, W. G.; Liao, B. T.

    2015-11-01

    Based on the analysis of the maturity and finiteness of vibrational levels of bromine molecule in ground state and evaluating the effect on statistical computation, according to the elementary principles of quantum statistical theorem, using the full set of bromine molecular vibrational levels determined with algebra method, the statistical contribution for bromine systematical macroscopic thermodynamic properties is discussed. Thermodynamic state functions Helmholtz free energy, entropy and observable vibration heat capacity are calculated. The results show that the determination of full set of vibrational levels and maximum vibrational quantum number is the key in the correct statistical analysis of bromine systematical thermodynamic property. Algebra method results are clearly different from data of simple harmonic oscillator and the related algebra method results are no longer analytical but numerical and are superior to simple harmonic oscillator results. Compared with simple harmonic oscillator's heat capacities, the algebra method's heat capacities are more consistent with the experimental data in the given temperature range of 600-2100 K.

  13. Two new brominated diterpenes from Laurencia decumbens

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Two new brominated diterpenes, namely, laurendecumtriol and 11-deacetylpinnaterpene C, were isolated and identified from the marine red alga Laurencia decumbens. Their structures were established on the basis of various NMR spectroscopic techniques and HR-ESI-MS analyses.

  14. Stability and metastability of bromine clathrate polymorphs.

    Science.gov (United States)

    Nguyen, Andrew H; Molinero, Valeria

    2013-05-23

    Clathrate hydrates are crystals in which water forms a network of fully hydrogen-bonded polyhedral cages that contain small guests. Clathrate hydrates occur mostly in two cubic crystal polymorphs, sI and sII. Bromine is one of two guests that yield a hydrate with the tetragonal structure (TS), the topological dual of the Frank-Kasper σ phase. There has been a long-standing disagreement on whether bromine hydrate also forms metastable sI and sII crystals. To date there are no data on the thermodynamic range of stability (e.g., the melting temperatures) of the metastable polymorphs. Here we use molecular dynamics simulations with the coarse-grained model of water mW to (i) investigate the thermodynamic stability of the empty and guest-filled the sI, sII, TS, and HS-I hydrate polymorphs, (ii) develop a coarse-grained model of bromine compatible with mW water, and (iii) evaluate the stability of the bromine hydrate polymorphs. The mW model predicts the same relative energy of the empty clathrate polymorphs and the same phase diagram as a function of water-guest interaction than the fully atomistic TIP4P water model. There is a narrow region in water-guest parameter space for which TS is marginally more stable than sI or sII. We parametrize a coarse-grained model of bromine compatible with mW water and use it to determine the order of stability of the bromine hydrate polymorphs. The melting temperatures of the bromine hydrate polymorphs predicted by the coarse-grained model are 281 ± 1 K for TS, 279 ± 1 K for sII, and 276 ± 1 K for sI. The closeness of the melting temperatures supports the plausibility of formation of metastable sII and sI bromine hydrates.

  15. Pulsed Bromine-81 Nuclear Quadrupole Resonance Spectroscopy of Brominated Flame Retardants and Associated Polymer Blends.

    Science.gov (United States)

    Mrse, Anthony A.; Lee, Youngil; Bryant, Pamela L.; Fronczek, Frank R.; Butler, Leslie G.; Simeral, Larry S.

    1998-03-01

    The dispersion of brominated flame retardants in polymers is monitored with bromine-81 NQR using a pulse NQR spectrometer. The NQR spectrometer consists of a homemade 10-300 MHz single-channel NMR console coupled to a broadly tunable probe. The probe is a loop-gap resonator usable from 220 to 300 MHz, and automatically tuned over any 5 MHz region with a stepping motor and an RF bidirectional coupler. Bromine-81 NQR spectra of several brominated aromatic flame retardants, as pure materials and in polymers, were recorded in the range of 227 to 256 MHz in zero applied magnetic field. Two factors affect the bromine-79/81 NQR transition frequencies in brominated aromatics: electron withdrawing substituents on the ring and intermolecular contacts with other bromine atoms in the crystal structure. An existing model for substituents is updated and a point charge model for the intermolecular contacts is developed. In this study, we exploit the bromine-81 NQR transition frequency dependence on intermolecular contacts to learn how a flame retardant is dispersed in a polymer matrix.

  16. A, a Brominated Flame Retardant

    Directory of Open Access Journals (Sweden)

    Tomomi Takeshita

    2013-01-01

    Full Text Available Tetrabromobisphenol A (TBBPA, a brominated flame retardant, has been found to exacerbate pneumonia in respiratory syncytial virus- (RSV- infected mice. We examined the effect of Brazilian propolis (AF-08 on the exacerbation of RSV infection by TBBPA exposure in mice. Mice were fed a powdered diet mixed with 1% TBBPA alone, 0.02% AF-08 alone, or 1% TBBPA and 0.02% AF-08 for four weeks and then intranasally infected with RSV. TBBPA exposure increased the pulmonary virus titer and level of IFN-γ, a representative marker of pneumonia due to RSV infection, in the lungs of infected mice without toxicity. AF-08 was significantly effective in reducing the virus titers and IFN-γ level increased by TBBPA exposure. Also, AF-08 significantly reduced proinflammatory cytokine (TNF-α and IL-6 levels in the lungs of RSV-infected mice with TBBPA exposure, but Th2 cytokine (IL-4 and IL-10 levels were not evidently increased. Neither TBBPA exposure nor AF-08 treatment affected the anti-RSV antibody production in RSV-infected mice. In flow cytometry analysis, AF-08 seemed to be effective in reducing the ratio of pulmonary CD8a+ cells in RSV-infected mice with TBBPA exposure. TBBPA and AF-08 did not exhibit anti-RSV activity in vitro. Thus, AF-08 probably ameliorated pneumonia exacerbated by TBBPA exposure in RSV-infected mice by limiting excess cellular immune responses.

  17. Abiotic Bromination of Soil Organic Matter.

    Science.gov (United States)

    Leri, Alessandra C; Ravel, Bruce

    2015-11-17

    Biogeochemical transformations of plant-derived soil organic matter (SOM) involve complex abiotic and microbially mediated reactions. One such reaction is halogenation, which occurs naturally in the soil environment and has been associated with enzymatic activity of decomposer organisms. Building on a recent finding that naturally produced organobromine is ubiquitous in SOM, we hypothesized that inorganic bromide could be subject to abiotic oxidations resulting in bromination of SOM. Through lab-based degradation treatments of plant material and soil humus, we have shown that abiotic bromination of particulate organic matter occurs in the presence of a range of inorganic oxidants, including hydrogen peroxide and assorted forms of ferric iron, producing both aliphatic and aromatic forms of organobromine. Bromination of oak and pine litter is limited primarily by bromide concentration. Fresh plant material is more susceptible to bromination than decayed litter and soil humus, due to a labile pool of mainly aliphatic compounds that break down during early stages of SOM formation. As the first evidence of abiotic bromination of particulate SOM, this study identifies a mechanistic source of the natural organobromine in humic substances and the soil organic horizon. Formation of organobromine through oxidative treatments of plant material also provides insights into the relative stability of aromatic and aliphatic components of SOM.

  18. 40 CFR 721.2925 - Brominated aromatic ester.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Brominated aromatic ester. 721.2925... Substances § 721.2925 Brominated aromatic ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a brominated aromatic ester (PMN...

  19. 40 CFR 721.3085 - Brominated phthalate ester.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Brominated phthalate ester. 721.3085... Substances § 721.3085 Brominated phthalate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as brominated phthalate ester (PMN P-90-581)...

  20. Nitrogenous disinfection byproducts in English drinking water supply systems: Occurrence, bromine substitution and correlation analysis.

    Science.gov (United States)

    Bond, Tom; Templeton, Michael R; Mokhtar Kamal, Nurul Hana; Graham, Nigel; Kanda, Rakesh

    2015-11-15

    Despite the recent focus on nitrogenous disinfection byproducts in drinking water, there is limited occurrence data available for many species. This paper analyses the occurrence of seven haloacetonitriles, three haloacetamides, eight halonitromethanes and cyanogen chloride in 20 English drinking water supply systems. It is the first survey of its type to compare bromine substitution factors (BSFs) between the haloacetamides and haloacetonitriles. Concentrations of the dihalogenated haloacetonitriles and haloacetamides were well correlated. Although median concentrations of these two groups were lower in chloraminated than chlorinated surface waters, median BSFs for both in chloraminated samples were approximately double those in chlorinated samples, which is significant because of the higher reported toxicity of the brominated species. Furthermore, median BSFs were moderately higher for the dihalogenated haloacetamides than for the haloacetonitriles. This indicates that, while the dihalogenated haloacetamides were primarily generated from hydrolysis of the corresponding haloacetonitriles, secondary formation pathways also contributed. Median halonitromethane concentrations were remarkably unchanging for the different types of disinfectants and source waters: 0.1 μg · mgTOC(-1) in all cases. Cyanogen chloride only occurred in a limited number of samples, yet when present its concentrations were higher than the other N-DBPs. Concentrations of cyanogen chloride and the sum of the halonitromethanes were not correlated with any other DBPs.

  1. Brominated flame retardants and endocrine disruption

    NARCIS (Netherlands)

    Vos, J.G.; Becher, G.; Berg, van den M.; Boer, de J.; Leonards, P.E.G.

    2003-01-01

    From an environmental point of view, an increasing important group of organohalogen compounds are the brominated flame retardants (BFRs), which are widely used in polymers and textiles and applied in construction materials, furniture, and electronic equipment. BFRs with the highest production volume

  2. Bromination of selected pharmaceuticals in water matrices.

    Science.gov (United States)

    Benitez, F Javier; Acero, Juan L; Real, Francisco J; Roldan, Gloria; Casas, Francisco

    2011-11-01

    The bromination of five selected pharmaceuticals (metoprolol, naproxen, amoxicillin, phenacetin, and hydrochlorothiazide) was studied with these compounds individually dissolved in ultra-pure water. The apparent rate constants for the bromination reaction were determined as a function of the pH, obtaining the sequence amoxicillin>naproxen>hydrochlorothiazide≈phenacetin≈metoprolol. A kinetic mechanism specifying the dissociation reactions and the species formed for each compound according to its pK(a) value and the pH allowed the intrinsic rate constants to be determined for each elementary reaction. There was fairly good agreement between the experimental and calculated values of the apparent rate constants, confirming the goodness of the proposed reaction mechanism. In a second stage, the bromination of the selected pharmaceuticals simultaneously dissolved in three water matrices (a groundwater, a surface water from a public reservoir, and a secondary effluent from a WWTP) was investigated. The pharmaceutical elimination trend agreed with the previously determined rate constants. The influence of the main operating conditions (pH, initial bromine dose, and characteristics of the water matrix) on the degradation of the pharmaceuticals was established. An elimination concentration profile for each pharmaceutical in the water matrices was proposed based on the use of the previously evaluated apparent rate constants, and the theoretical results agreed satisfactorily with experiment. Finally, chlorination experiments performed in the presence of bromide showed that low bromide concentrations slightly accelerate the oxidation of the selected pharmaceuticals during chlorine disinfection.

  3. Membrane-less hydrogen bromine flow battery.

    Science.gov (United States)

    Braff, William A; Bazant, Martin Z; Buie, Cullen R

    2013-01-01

    In order for the widely discussed benefits of flow batteries for electrochemical energy storage to be applied at large scale, the cost of the electrochemical stack must come down substantially. One promising avenue for reducing stack cost is to increase the system power density while maintaining efficiency, enabling smaller stacks. Here we report on a membrane-less hydrogen bromine laminar flow battery as a potential high-power density solution. The membrane-less design enables power densities of 0.795 W cm(-2) at room temperature and atmospheric pressure, with a round-trip voltage efficiency of 92% at 25% of peak power. Theoretical solutions are also presented to guide the design of future laminar flow batteries. The high-power density achieved by the hydrogen bromine laminar flow battery, along with the potential for rechargeable operation, will translate into smaller, inexpensive systems that could revolutionize the fields of large-scale energy storage and portable power systems.

  4. Membrane-less hydrogen bromine flow battery

    CERN Document Server

    Braff, W A; Buie, C R

    2014-01-01

    In order for the widely discussed benefits of flow batteries for electrochemical energy storage to be applied at large scale, the cost of the electrochemical stack must come down substantially. One promising avenue for reducing stack cost is to increase the system power density while maintaining efficiency, enabling smaller stacks. Here we report on a membrane-less, hydrogen bromine laminar flow battery as a potential high power density solution. The membrane-less design enables power densities of 0.795 W cm$^{-2}$ at room temperature and atmospheric pressure, with a round-trip voltage efficiency of 92\\% at 25\\% of peak power. Theoretical solutions are also presented to guide the design of future laminar flow batteries. The high power density achieved by the hydrogen bromine laminar flow battery, along with the potential for rechargeable operation, will translate into smaller, inexpensive systems that could revolutionize the fields of large-scale energy storage and portable power systems.

  5. NMR investigation of non-brominated and brominated epoxy ester prepolymers

    Science.gov (United States)

    Žigon, M.; Osredkar, U.; Šebenik, A.

    1992-03-01

    1H, 13C and two-dimensional NMR spectroscopy has been used to investigate the structure of epoxy ester prepolymers, based on non-brominated DGEBA-type or brominated DGETBBA-type epoxy resins, and on an oligomeric carboxylic acid. In the presence of a quaternary phosphonium salt, besides diglycidylether of bisphenol A (DGEBA) or diglycidylether of tetrabromobisphenol A (DGETBBA) and their higher oligomers, monoesters with characteristic R-CH 2-CH(OH)-CH 2-OCOR' groups were detected in prevailing quantities. In dependence of the epoxy-carboxy ratio, isomeric monoesters with hydroxymethyl groups, diesters and diols might also be present.

  6. Chloride transference during electrochemical chloride extraction process

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Chemical titration method and lab-made chloride probes were jointly adopted to investigate the effects of water-to-cement (W/C) ratio and the impressed current density on chloride transport for cement-based materials during electrochemical chloride extraction (ECE) process.The dissolution of bound chlorides and the effect of current density on dissolution were analyzed.The variations of chloride concentration at different depths and the chloride transference process were monitored.Test results show that W/C ratios adopted have slight influence on chloride extraction,while chloride extraction efficiency is mainly determined by the impressed current density.During ECE process a portion of bound chloride ions dissolved and the amount of bound chlorides released is directly proportional to current density.

  7. Polyvinylpolypyrrolidone-bromine complex: Mild and efficient polymeric reagent for bromination of activated aromatic compounds

    Institute of Scientific and Technical Information of China (English)

    Masoud Mokhtary; Moslem M. Lakouraj

    2011-01-01

    Mild and efficient method for bromination of electron-rich aromatic compounds is described using polyvinylpolypyrrolidonebromine complex (PVPP-Br2). The reaction proceeded smoothly with phenols and N,N-alkylated amines to afford the corresponding monobrominated product in good yields at ambient temperature.

  8. The Addition of Bromine to 1,2-Diphenylethene

    Science.gov (United States)

    Amburgey-Peters, Judith C.; Haynes, Leroy W.

    2005-01-01

    The bromination of 1,2-diphenylethene, using a variety of solvents and brominating agents, can be used in both introductory and advanced organic chemistry courses. The reactions can be used to illustrate the effects of changing solvents and reagents, as well as to reveal interesting aspects of organic reaction mechanisms.

  9. Fire-retardant coatings based on organic bromine/phenoxy or brominated epoxy systems

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, D.M.; Chiu, Ing L.

    1989-06-01

    Thin phenoxy and brominated epoxy/curing agent films were prepared by solvent casting on Mylar and Kapton. Thicknesses were approximated assuming volume additivity. Important parameters were uniformity of thickness, distribution of the bromine-containing fire retardant, adhesion to carrier substrate (either Mylar or Kapton), and uniformity of the coating, i.e., absence of pinholes, blush, blistering, etc. Wetting behavior was modified using fluoro, silicone or polyurea surfactants. Several solvent systems were examined and a ternary solvent system was ultimately used. Distribution of fire-retardant bromine was analyzed using electron microprobe, x-ray fluorescence and wet chemical methods. Significant discrepancies in the /mu/m-scale analyses of the microprobe measurements have not been resolved. Some of the brominated fire retardants were insoluble in the resin systems and the phase separation was immediately obvious. Similarly, some of the crystallizable epoxies could not be cast easily into homogeneous, amorphous films. Castings were made on a standard 8'' /times/ 10'' aluminum vacuum plate polished with jeweler's rouge prior to every casting. Solvent was removed in a forced air or vacuum oven. Removal and/or curing was accelerated with temperature. The fire-retardant bromine was required to be stable in alcohol/salt solutions. Final formulation used after a significant amount of testing was phenoxy resin PKHC in a ternary solvent system composed of methylethyl ketone, cellosolve acetate and toluene. Tetrabromobisphenol A was used as the flame retardant with FC-430 as surfactant. The dying schedule was 30 minutes at 150/degree/C. 4 refs., 6 figs., 3 tabs.

  10. Formation of THMs and HANs during bromination of Microcystis aeruginosa

    Institute of Scientific and Technical Information of China (English)

    Yunzhu Pu; Lingzhao Kong; Xin Huang; Guoji Ding; Naiyun Gao

    2013-01-01

    Bromine-contained disinfectants and biocides are widely used in swimming pools,recreational waters and cooling towers.The objective of this study was to evaluate the formation of thrihalomethanes (THMs) and haloacetonitriles (HANs) and their cytotoxicity in algae solutions during free bromine disinfection.Disinfection by-products formation potential experiments were conducted using modelsolutions containing 7mg/L (as total organic carbon) Microcystis aeruginosa cells.Effects of free bromine dosage,pH and ammonia were investigated.The results showed that brominated disinfection by-products were the major products when free bromine was applied.The total THMs formed during bromination was much as that formed during chlorination,whereas HANs were elevated by using bromination instead of chlorination.Dibromoacetonitrice (C2H2NBr2) and bromoform (CHBr3) were the only detected species during free bromine disinfection.The production of C2H2NBr2 and CHBr3 increased with disinfectant dosage but decreased with dosing ammonia.CHBr3 increased with the pH changing from 5 to 9.However,C2H2NBr2 achieved the highest production at neutral pH,which was due to a joint effect of variation in hydrolysis rate and free bromine reactivity.The hydrolysis of C2H2NBr2 was basecatalytic and nearly unaffected by disinfectant.Finally,estimation of cytotoxicity of the disinfected algae solutions showed that HANs formation was responsible for the majority of toxicity.Considering its highest toxicity among the measured disinfection by-products,the elevated C2H2NBr2 should be considered when using bromine-related algaecide.

  11. New infrared spectroscopic database for bromine nitrate

    Science.gov (United States)

    Wagner, Georg; Birk, Manfred

    2016-08-01

    Fourier transform infrared measurements of bromine nitrate have been performed in the spectral region 675-1400 cm-1 at 0.014 cm-1 spectral resolution. Absorption cross sections were derived from 38 spectra covering the temperature range from 203 to 296 K and air pressure range from 0 to 190 mbar. For line-by-line analysis, further spectra were recorded at 0.00094 cm-1 spectral resolution at 223 and 293 K. The sample was synthesized from ClONO2 and Br2. Band strengths of the bands ν3 around 803 cm-1 and ν2 around 1286 cm-1 were determined from three pure BrONO2 measurements at different temperatures and pressures. Number densities in the absorption cell were derived from pressure measurements of the purified sample taking into account small amounts of impurities determined spectroscopically. Resulting band strengths are Sν3 = 2.872(52) × 10-17 cm2 molec-1 cm-1 and Sν2 = 3.63(15) × 10-17 cm2 molec-1 cm-1. Absorption cross sections of all measurements were scaled to these band strengths. Further data reduction was achieved with an interpolation scheme based on two-dimensional polynomials in ln(pressure) and temperature. The database is well-suited for remote-sensing application and should reduce the atmospheric bromine nitrate error budget substantially.

  12. Tribenzylammonium chloride

    Directory of Open Access Journals (Sweden)

    Waly Diallo

    2014-05-01

    Full Text Available Single crystals of the title salt, C21H21NH+·Cl−, were isolated as a side product from the reaction involving [(C6H5CH23NH]2[HPO4] and Sn(CH33Cl in ethanol. Both the cation and the anion are situated on a threefold rotation axis. The central N atom in the cation has a slightly distorted tetrahedral environment, with angles ranging from 107.7 to 111.16 (10°. In the crystal, the tribenzylammonium cations and chloride anions are linked through N—H...Cl and C—H...Cl hydrogen bonds, leading to the formation of infinite chains along [001]. The crystal studied was a merohedral twin.

  13. Use of Bromine and Bromo-Organic Compounds in Organic Synthesis.

    Science.gov (United States)

    Saikia, Indranirekha; Borah, Arun Jyoti; Phukan, Prodeep

    2016-06-22

    Bromination is one of the most important transformations in organic synthesis and can be carried out using bromine and many other bromo compounds. Use of molecular bromine in organic synthesis is well-known. However, due to the hazardous nature of bromine, enormous growth has been witnessed in the past several decades for the development of solid bromine carriers. This review outlines the use of bromine and different bromo-organic compounds in organic synthesis. The applications of bromine, a total of 107 bromo-organic compounds, 11 other brominating agents, and a few natural bromine sources were incorporated. The scope of these reagents for various organic transformations such as bromination, cohalogenation, oxidation, cyclization, ring-opening reactions, substitution, rearrangement, hydrolysis, catalysis, etc. has been described briefly to highlight important aspects of the bromo-organic compounds in organic synthesis.

  14. TG-MS investigation of brominated products from the degradation of brominated flame retardants in high-impact polystyrene.

    Science.gov (United States)

    Grause, Guido; Karakita, Daiki; Ishibashi, Jun; Kameda, Tomohito; Bhaskar, Thallada; Yoshioka, Toshiaki

    2011-10-01

    The thermal degradation of flame retardant containing high-impact polystyrene (HIPS-Br), one of the most commonly employed plastics in electric and electronic appliances, was examined by thermogravimetry coupled with mass spectroscopy (TG-MS) in order to understand the threat that is posed by the release of hazardous brominated compounds. The HIPS samples contained decabromodiphenylether (DPE) and decabromodibenzyl (DDB) as the flame retardants as well as Sb2O3 as the synergist. The largest number of brominated compounds was obtained in the presence of DPE and Sb2O3 and DDB without Sb2O3. From the degradation of DPE, brominated benzenes, phenols, diphenylethers, and dibenzofurans were identified, and from the degradation of DDB, brominated benzenes, dibenzyls, and phenanthrenes were formed. The interaction between the flame retardant and the polymer matrix resulted in α-bromoethylbenzene. The formation of brominated dibenzodioxins was not observed, probably, due to the low phenol concentration in the polymer melt. No other report has, to our knowledge, ever reported on the formation of brominated phenanthrenes from flame retardants. Because they share similar steric features, it may well be that brominated phenanthrenes are similar in their carcinogen and mutagen potential to dibenzofurans and dibenzodioxins. A plausible mechanism for the formation of the observed compounds is presented, and the role of the synergist is considered.

  15. Oxidative treatment of bromide-containing waters: formation of bromine and its reactions with inorganic and organic compounds--a critical review.

    Science.gov (United States)

    Heeb, Michèle B; Criquet, Justine; Zimmermann-Steffens, Saskia G; von Gunten, Urs

    2014-01-01

    Bromide (Br(-)) is present in all water sources at concentrations ranging from ≈ 10 to >1000 μg L(-1) in fresh waters and about 67 mg L(-1) in seawater. During oxidative water treatment bromide is oxidized to hypobromous acid/hypobromite (HOBr/OBr(-)) and other bromine species. A systematic and critical literature review has been conducted on the reactivity of HOBr/OBr(-) and other bromine species with inorganic and organic compounds, including micropollutants. The speciation of bromine in the absence and presence of chloride and chlorine has been calculated and it could be shown that HOBr/OBr(-) are the dominant species in fresh waters. In ocean waters, other bromine species such as Br2, BrCl, and Br2O gain importance and may have to be considered under certain conditions. HOBr reacts fast with many inorganic compounds such as ammonia, iodide, sulfite, nitrite, cyanide and thiocyanide with apparent second-order rate constants in the order of 10(4)-10(9)M(-1)s(-1) at pH 7. No rate constants for the reactions with Fe(II) and As(III) are available. Mn(II) oxidation by bromine is controlled by a Mn(III,IV) oxide-catalyzed process involving Br2O and BrCl. Bromine shows a very high reactivity toward phenolic groups (apparent second-order rate constants kapp ≈ 10(3)-10(5)M(-1)s(-1) at pH 7), amines and sulfamides (kapp ≈ 10(5)-10(6)M(-1)s(-1) at pH 7) and S-containing compounds (kapp ≈ 10(5)-10(7)M(-1)s(-1) at pH 7). For phenolic moieties, it is possible to derive second-order rate constants with a Hammett-σ-based QSAR approach with [Formula in text]. A negative slope is typical for electrophilic substitution reactions. In general, kapp of bromine reactions at pH 7 are up to three orders of magnitude greater than for chlorine. In the case of amines, these rate constants are even higher than for ozone. Model calculations show that depending on the bromide concentration and the pH, the high reactivity of bromine may outweigh the reactions of chlorine during

  16. Bromine pretreated chitosan for adsorption of lead (II) from water

    Indian Academy of Sciences (India)

    Rajendra Dongre; Minakshi Thakur; Dinesh Ghugal; Jostna Meshram

    2012-10-01

    Pollution by heavy metals like lead (II) is responsible for health hazards and environmental degradation. Adsorption is a prevalent method applied for removal of heavy metal pollutants from water. This study explored adsorption performances of 30% bromine pretreated chitosan for lead (II) abatement from water. Bromine pretreatment alters porosity and specific surface area of chitosan by means of physicochemical interaction with cationic sites of chitosan skeleton, besides imparting anionic alteration at amino linkages of chitosan, to remove lead (II) by chemical interactions on superfluous active sites as characterized by FTIR, SEM, DTA and elemental analysis. Lead adsorptions were studied in batch mode by varying parameters viz. pH, bromine loading, sorbent dosage, initial lead concentration, contact time and temperature. The adsorption equilibrium data was well fitted to Freundlich isotherm and maximum sorption capacity of 30% bromine pretreated chitosan sorbent was 1.755 g/kg with 85–90% lead removal efficiency. Though cost and applicability of sorbent is unproven, yet contrast to raw chitosan derivatives, activated carbons and some resins, 30% bromine pretreated chitosan endow benign and efficient lead abatement technique.

  17. Fate of higher brominated PBDEs in lactating cows.

    Science.gov (United States)

    Kierkegaard, Amelie; Asplund, Lillemor; de Wit, Cynthia A; McLachlan, Michael S; Thomas, Gareth O; Sweetman, Andrew J; Jones, Kevin C

    2007-01-15

    Dietary intake studies of lower brominated diphenyl ethers (BDEs) have shown that fish and animal products are important vectors of human exposure, but almost no data exist for higher brominated BDEs. Therefore, the fate of hepta- to decaBDEs was studied in lactating cows exposed to a naturally contaminated diet by analyzing feed, feces, and milk samples from a previous mass balance study of PCB. Tissue distribution was studied in one cow slaughtered after the experiment. BDE-209 was the dominant congener in feed, organs, adipose tissues, and feces, but not in milk. In contrast to PCBs and lower brominated BDEs, concentrations of hepta- to decaBDEs in adipose tissue were 9-80 times higher than in milk fat and the difference increased with degree of bromination/log K(OW). The congener profiles in adipose tissue and feed differed; BDE-207, BDE-196, BDE-197, and BDE-182 accumulated to a surprisingly greater extent in the fat compared to their isomers, suggesting metabolic debromination of BDE-209 to these BDEs. The results indicate that meat rather than dairy product consumption may be an important human exposure route to higher brominated BDEs.

  18. Environmental monitoring of brominated flame retardants

    Science.gov (United States)

    Vagula, Mary C.; Kubeldis, Nathan; Nelatury, Charles F.

    2011-06-01

    Brominated flame retardants (BFRs) are synthetic organobromide compounds which inhibit ignition and combustion processes. Because of their immense ability to retard fire and save life and property, they have been extensively used in many products such as TVs, computers, foam, plastics etc. The five major classes of BFRs are tetrabromobisphenol-A (TBBPA), hexabromocyclododecane (HBCD), pentabromodiphenyl ether, octabromodiphenyl ether, and decabromodiphenyl ether. The last three are also commonly called PBDEs. BDE-85 and BDE-209 are the two prominent congeners of PBDEs and this study reports the adverse effects of these congeners in rodents. Exposure of rat sciatic nerves to 5 μg/mL and 20 μg/mL of BDE-85 and BDE-209 respectively lead to significant, concentration dependent reduction in nerve conduction function. Glucose absorption in the rat intestinal segments exposed to 5 μg/mL of BDE-85 and BDE-209 was significantly reduced for both the compounds tested. Lastly, mice when exposed to 0.25 mg/kg body weight for four days showed a disruption in oxidant and antioxidant equilibrium. The tissues namely liver and brain have shown increase in the levels of lipid hydroperoxides indicating oxidative stress. Moreover, all the protective enzymes namely superoxide dismutase (SOD), glutathione peroxidase (GPx), catalase, and glutathione S transferase (GST) have shown tissue specific alterations indicating the induction of damaging oxidative stress and setting in of lipid peroxidation in exposed animals. The results indicate monitoring of PBDEs in the environment is essential because levels as low as 5 μg/mL and 0.25 mg/kg body weight were able to cause damage to the functions of rodents.

  19. The geochemistry of stable chlorine and bromine isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Eggenkamp, Hans [Onderzock and Beleving, Bussum (Netherlands)

    2014-11-01

    First book solely dedicated to the geochemistry of chlorine and bromine isotopes. Detailed description of analytical techniques, including their advantages and disadvantages. Indication of research fields where measurement of these isotopes is especially useful. This book provides detailed information on the history, analysis and applications of chlorine and bromine isotope geochemistry. Chlorine and bromine are geochemically unique as they prefer to exist as single charged negative ions. For this reason isotope fractionation reflects mostly processes that are not related to changes in the redox state and this fractionation is generally modest. The book will describe the processes that are most easily detected using these isotopes. Also isotope variations, and processes that cause them, measured in oxidised species such as perchlorates and in organic molecules will be described in this book.

  20. 40 CFR 180.519 - Bromide ion and residual bromine; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Bromide ion and residual bromine... Tolerances § 180.519 Bromide ion and residual bromine; tolerances for residues. (a) General. The food additives, bromide ion and residual bromine, may be present in water, potable in accordance with...

  1. An Efficient and Facile Methodology for Bromination of Pyrimidine and Purine Nucleosides with Sodium Monobromoisocyanurate (SMBI

    Directory of Open Access Journals (Sweden)

    Roger Stromberg

    2013-10-01

    Full Text Available An efficient and facile strategy has been developed for bromination of nucleosides using sodium monobromoisocyanurate (SMBI. Our methodology demonstrates bromination at the C-5 position of pyrimidine nucleosides and the C-8 position of purine nucleosides. Unprotected and also several protected nucleosides were brominated in moderate to high yields following this procedure.

  2. Sensing and inactivation of Bacillus anthracis Sterne by polymer-bromine complexes.

    Science.gov (United States)

    D'Angelo, Paola A; Bromberg, Lev; Hatton, T Alan; Wilusz, Eugene

    2016-08-01

    We report on the performance of brominated poly(N-vinylpyrrolidone) (PVP-Br), brominated poly(ethylene glycol) (PEG-Br), and brominated poly(allylamine-co-4-aminopyridine) (PAAm-APy-Br) for their ability to decontaminate Bacillus anthracis Sterne spores in solution while also allowing for the sensing of the spores. The polymers were brominated by bromine using carbon tetrachloride or potassium tribromide as solvents, with bromine loadings ranging from 1.6 to 4.2 mEq/g of polymer. B. anthracis Sterne spores were exposed to increasing concentrations of brominated polymers for 5 min, while the kinetics of the sporicidal activity was assessed. All brominated polymers demonstrated spore log-kills of 8 within 5 min of exposure at 12 mg/mL aqueous polymer concentration. Sensing of spores was accomplished by measuring the release of dipicolinic acid (DPA) from the spore using time-resolved fluorescence. Parent, non-brominated polymers did not cause any release of DPA and the spores remained viable. In contrast, spores exposed to the brominated polymers were inactivated and the release of DPA was observed within minutes of exposure. Also, this release of DPA continued for a long time after spore inactivation as in a controlled release process. The DPA release was more pronounced for spores exposed to brominated PVP and brominated PEG-8000 compared to brominated PAAm-APy and brominated PEG-400. Using time-resolved fluorescence, we detected as low as 2500 B. anthracis spores, with PEG-8000 being more sensitive to low spore numbers. Our results suggest that the brominated polymers may be used effectively as decontamination agents against bacterial spores while also providing the sensing capability.

  3. Brominated Dioxins: Little-Known New Health Hazards - A Review

    Directory of Open Access Journals (Sweden)

    Piskorska-Pliszczyńska Jadwiga

    2014-10-01

    Full Text Available This article reviews the present state of the science concerning the polybrominated dibenzo-p-dioxins (PBDDs and dibenzofurans (PBDFs. Everywhere in the world people are exposed to anthropogenic origin chemicals. Some of them are long-lived organic compounds, which persist over the years in the environment. Persistent organic pollutants, such as organohalogen compounds, accumulate in environmental and biological compartments and have adverse effects on the health of humans and animals. Little is known about the brominated and mixed chloro/bromo dioxin and furans. Existing literature suggests that brominated dioxins and furans have similar toxicity profiles to their chlorinated analogues. The exposure data are extremely limited, showing a major data gap in estimating the potential environmental and health risk of these chemicals. The rapid increase in the use of brominated flame retardants (the main source of these pollutants has raised the level of concern over environmental and health damage from brominated dioxins and furans. It is likely that human as well as wildlife exposure to these contaminants will increase with their greater use. The findings reported here present strong evidence of the PBDDs and PBDFs as an emerging new class of contaminants.

  4. A Sternheimer-like response property of the bromine molecule

    Science.gov (United States)

    Fowler, P. W.; Peebles, S. A.; Legon, A. C.

    The generalised polarisability describing the response to an applied field of the electric field gradient at a nucleus in Br2 is calculated ab initio. A value of 110.55 a-10 is found at the self-consistent -field level. This is about half the value derived by modelling the measured nuclear quadrupole coupling constants of theammonia-bromine complex.

  5. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents the state-of-the art: an analytical model which describes chloride profiles in concrete as function of depth...... makes physical sense for the design engineer, i.e. the achieved chloride diffusion coefficients at 1 year and 100 years, D1 and D100 respectively, and the corresponding achieved chloride concentrations at the exposed concrete surface, C1 and C100. Data from field exposure supports the assumption of time...... dependent surface chloride concentrations and the diffusion coefficients. Model parameters for Portland cement concretes with and without silica fume and fly ash in marine atmospheric and submerged South Scandinavian environment are suggested in a companion paper based on 10 years field exposure data....

  6. Bromine measurements in ozone depleted air over the Arctic Ocean

    Directory of Open Access Journals (Sweden)

    J. A. Neuman

    2010-07-01

    Full Text Available In situ measurements of ozone, photochemically active bromine compounds, and other trace gases over the Arctic Ocean in April 2008 are used to examine the chemistry and geographical extent of ozone depletion in the arctic marine boundary layer (MBL. Data were obtained from the NOAA WP-3D aircraft during the Aerosol, Radiation, and Cloud Processes affecting Arctic Climate (ARCPAC study and the NASA DC-8 aircraft during the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS study. Fast (1 s and sensitive (detection limits at the low pptv level measurements of BrCl and BrO were obtained from three different chemical ionization mass spectrometer (CIMS instruments, and soluble bromide was measured with a mist chamber. The CIMS instruments also detected Br2. Subsequent laboratory studies showed that HOBr rapidly converts to Br2 on the Teflon instrument inlets. This detected Br2 is identified as active bromine and represents a lower limit of the sum HOBr + Br2. The measured active bromine is shown to likely be HOBr during daytime flights in the arctic. In the MBL over the Arctic Ocean, soluble bromide and active bromine were consistently elevated and ozone was depleted. Ozone depletion and active bromine enhancement were confined to the MBL that was capped by a temperature inversion at 200–500 m altitude. In ozone-depleted air, BrO rarely exceeded 10 pptv and was always substantially lower than soluble bromide that was as high as 40 pptv. BrCl was rarely enhanced above the 2 pptv detection limit, either in the MBL, over Alaska, or in the arctic free troposphere.

  7. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash...... in marine atmospheric and submersed South Scandinavian environment. The design parameters are based on sequential measurements of 86 chloride profiles taken over ten years from 13 different types of concrete. The design parameters provide the input for an analytical model for chloride profiles as function...

  8. 五溴苄基氯的合成新工艺%A Novel Synthetic Process of Pentabromobenzyl Chloride

    Institute of Scientific and Technical Information of China (English)

    徐元清; 郭红丽; 房晓敏; 丁涛; 张永光; 牛国臣

    2011-01-01

    A novel one - step synthetic process of pentabromobenzyl chloride was reported, using benzyl chloride as raw material, bromine as solvent as well as bromination reactant, and anhydrous aluminum trichloride as catalyst. The bromination proceeded entirely, giving rise to a high quality of product, and the yield was as high as 99.0%. The structure of pentabromobenzyl chloride was determined by both FT - IR and ' H NMR. Themal gravimetric analysis revealed that the product possesses high thermal stability.%报道了一种阻燃剂五溴苄基氯的合成新工艺,即以氯化苄为原料,液澳为反应物及溶剂,无水三氯化铝为催化剂,经一步反应制备目标产品.该溴化反应完全,产品质量好,产品收率高达99.0%.红外和核磁分析表明产品结构正确;热分析表明产品的热稳定性较高.

  9. Substrate Directed Regioselective Monobromination of Aralkyl Ketones Using N-Bromosuccinimide Catalysed by Active Aluminium Oxide: α -Bromination versus Ring Bromination.

    Science.gov (United States)

    Mohan, Reddy Bodireddy; Reddy, G Trivikram; Gangi Reddy, N C

    2014-01-01

    Bromination of aralkyl ketones using N-bromosuccinimide in presence of active Al2O3 provided either α -monobrominated products in methanol at reflux or mononuclear brominated products in acetonitrile at reflux temperature with excellent isolated yields depending on the nature of substrate employed. The α -bromination was an exclusive process when aralkyl ketones containing moderate activating/deactivating groups were subjected to bromination under acidic Al2O3 conditions in methanol at reflux while nuclear functionalization was predominant when aralkyl ketones containing high activating groups were utilized for bromination in presence of neutral Al2O3 conditions in acetonitrile at reflux temperature. In addition, easy isolation of products, use of inexpensive catalyst, short reaction time (10-20 min), and safe operational practice are the major benefits in the present protocol.

  10. The crystal structure and superconducting properties of monatomic bromine.

    Science.gov (United States)

    Duan, Defang; Meng, Xing; Tian, Fubo; Chen, Changbo; Wang, Liancheng; Ma, Yanming; Cui, Tian; Liu, Bingbing; He, Zhi; Zou, Guangtian

    2010-01-13

    The crystal structure and superconducting properties of monatomic bromine under high pressure have been studied by first-principles calculations. We have found the following phase transition sequence with increasing pressure: from body-centered orthorhombic (bco, phase II) to body-centered tetragonal structure (bct, phase III) at 126 GPa, then to face-centered cubic structure (fcc, phase IV) at 157 GPa, which is stable at least up to 300 GPa. The calculated superconducting critical temperature T(c) = 1.46 K at 100 GPa is consistent with the experimental value of 1.5 K. In addition, our results of T(c) decrease with increasing pressure in all the monatomic phases of bromine, similar to monatomic iodine. Further calculations show that the decrease of λ with pressure in phase IV is mainly attributed to the weakening of the 'soft' vibrational mode caused by pressure.

  11. New Methods for Labeling RGD Peptides with Bromine-76

    Directory of Open Access Journals (Sweden)

    Lixin Lang, Weihua Li, Hong-Mei Jia, De-Cai Fang, Shushu Zhang, Xilin Sun, Lei Zhu, Ying Ma, Baozhong Shen, Dale O. Kiesewetter, Gang Niu, Xiaoyuan Chen

    2011-01-01

    Full Text Available Direct bromination of the tyrosine residues of peptides and antibodies with bromine-76, to create probes for PET imaging, has been reported. For peptides that do not contain tyrosine residues, however, a prosthetic group is required to achieve labeling via conjugation to other functional groups such as terminal α-amines or lysine ε-amines. The goal of this study was to develop new strategies for labeling small peptides with Br-76 using either a direct labeling method or a prosthetic group, depending on the available functional group on the peptides. A new labeling agent, N-succinimidyl-3-[76Br]bromo-2,6-dimethoxybenzoate ([76Br]SBDMB was prepared for cyclic RGD peptide labeling. N-succinimidyl-2, 6-dimethoxybenzoate was also used to pre-attach a 2, 6-dimethoxybenzoyl (DMB moiety to the peptide, which could then be labeled with Br-76. A competitive cell binding assay was performed to determine the binding affinity of the brominated peptides. PET imaging of U87MG human glioblastoma xenografted mice was performed using [76Br]-BrE[c(RGDyK]2 and [76Br]-BrDMB-E[c(RGDyK]2. An ex vivo biodistribution assay was performed to confirm PET quantification. The mechanisms of bromination reaction between DMB-c(RGDyK and the brominating agent CH3COOBr were investigated with the SCRF-B3LYP/6-31G* method with the Gaussian 09 program package. The yield for direct labeling of c(RGDyK and E[c(RGDyK]2 using chloramine-T and peracetic acid at ambient temperature was greater than 50%. The yield for [76Br]SBDMB was over 60% using peracetic acid. The conjugation yields for labeling c(RGDfK and c(RGDyK were over 70% using the prosthetic group at room temperature. Labeling yield for pre-conjugated peptides was over 60%. SDMB conjugation and bromination did not affect the binding affinity of the peptides with integrin receptors. Both [76Br]Br-E[c(RGDyK]2 and [76Br]BrDMB-E[c(RGDyK]2 showed high tumor uptake in U87MG tumor bearing mice. The specificity of the imaging tracers

  12. Bromination of hydrocarbons with CBr4, initiated by light-emitting diode irradiation

    Directory of Open Access Journals (Sweden)

    Yuta Nishina

    2013-08-01

    Full Text Available The bromination of hydrocarbons with CBr4 as a bromine source, induced by light-emitting diode (LED irradiation, has been developed. Monobromides were synthesized with high efficiency without the need for any additives, catalysts, heating, or inert conditions. Action and absorption spectra suggest that CBr4 absorbs light to give active species for the bromination. The generation of CHBr3 was confirmed by NMR spectroscopy and GC–MS spectrometry analysis, indicating that the present bromination involves the homolytic cleavage of a C–Br bond in CBr4 followed by radical abstraction of a hydrogen atom from a hydrocarbon.

  13. Specific heat of pristine and brominated graphite fibers, composites and HOPG. [Highly Oriented Pyrolytic Graphite

    Science.gov (United States)

    Hung, Ching-Chen; Maciag, Carolyn

    1987-01-01

    Differential scanning calorimetry was used to obtain specific heat values of pristine and brominated P-100 graphite fibers and brominated P-100/epoxy composite as well as pristine and brominated highly oriented pyrolytic graphite (HOPG) for comparison. Based on the experimental results obtained, specific heat values are calculated for several different temperatures, with a standard deviation estimated at 1.4 percent of the average values. The data presented here are useful in designing heat transfer devices (such as airplane de-icing heaters) from bromine fibers.

  14. Elemental Bromine Production by TiO2 Photocatalysis and/or Ozonation.

    Science.gov (United States)

    Parrino, Francesco; Camera Roda, Giovanni; Loddo, Vittorio; Palmisano, Leonardo

    2016-08-22

    Significant production of elemental bromine (Br2 ) was observed for the first time when treating bromide containing solutions at acidic pH, with TiO2 photocatalyst, ozone, or a combination thereof. Br2 selectivities up to approximately 85 % were obtained and the corresponding bromine mass balance values satisfied. The process is general and may be applied at a laboratory scale for green bromination reactions, or industrially as a cheap, safe, and environmentally sustainable alternative to the currently applied bromine production methods.

  15. High selectively oxidative bromination of toluene derivatives by the H2O2-HBr system

    Institute of Scientific and Technical Information of China (English)

    Jie Ju; Yu Jin Li; Jian Rong Gao; Jian Hong Jia; Liang Han; Wei Jian Sheng; Yi Xia Jia

    2011-01-01

    An aqueous solution of hydrogen peroxide and hydrogen bromide illuminated by a 60 W incandescent light bulb serves as a source of bromine radicals. Various substituted toluenes (NO2,Cl, Br, H, CH3) were high selectively brominated at the benzyl position for monobromination in CH2C12 at ice water with catalyst free. This simple but effective bromination of toluene derivatives with an aqueous H2O2-HBr system is characterized with the use of inexpensive reagents and a lower impact on the environment, which make it a good alternative to the existing bromination methods.

  16. Measurement-based modeling of bromine chemistry in the boundary layer: 1. Bromine chemistry at the Dead Sea

    OpenAIRE

    Tas, E.; M. Peleg; D. U. Pedersen; Matveev, V; A. Pour Biazar; Luria, M.

    2006-01-01

    International audience; The Dead Sea is an excellent natural laboratory for the investigation of Reactive Bromine Species (RBS) chemistry, due to the high RBS levels observed in this area, combined with anthropogenic air pollutants up to several ppb. The present study investigated the basic chemical mechanism of RBS at the Dead Sea using a numerical one-dimensional chemical model. Simulations were based on data obtained from comprehensive measurements performed at sites along the Dead Sea. Th...

  17. Measurement-based modeling of bromine chemistry in the boundary layer: 1. Bromine chemistry at the Dead Sea

    OpenAIRE

    A. Pour Biazar; Matveev, V; D. U. Pedersen; M. Peleg; Tas, E.; Luria, M.

    2006-01-01

    The Dead Sea is an excellent natural laboratory for the investigation of Reactive Bromine Species (RBS) chemistry, due to the high RBS levels observed in this area, combined with anthropogenic air pollutants up to several ppb. The present study investigated the chemical mechanism of RBS at the Dead Sea using a numerical one-dimensional chemical model. Simulations were based on data obtained from comprehensive measurements performed at sites along the Dead Sea. The simulations showed that the ...

  18. Lithium Sulfuryl Chloride Battery.

    Science.gov (United States)

    Primary batteries , Electrochemistry, Ionic current, Electrolytes, Cathodes(Electrolytic cell), Anodes(Electrolytic cell), Thionyl chloride ...Phosphorus compounds, Electrical conductivity, Calibration, Solutions(Mixtures), Electrical resistance, Performance tests, Solvents, Lithium compounds

  19. Inorganic bromine in the marine boundary layer: a critical review

    Directory of Open Access Journals (Sweden)

    R. Sander

    2003-06-01

    Full Text Available The cycling of inorganic bromine in the marine boundary layer (mbl has received increased attention in recent years. Bromide, a constituent of sea water, is injected into the atmosphere in association with sea-salt aerosol by breaking waves on the ocean surface. Measurements reveal that supermicrometer sea-salt aerosol is depleted in bromine by about 50% relative to conservative tracers, whereas marine submicrometer aerosol is often enriched in bromine. Model calculations, laboratory studies, and field observations strongly suggest that these depletions reflect the chemical transformation of particulate bromide to reactive inorganic gases that influence the processing of ozone and other important constituents of marine air. However, currently available techniques cannot reliably quantify many chem{Br}-containing compounds at ambient concentrations and, consequently, our understanding of inorganic Br cycling over the oceans and its global significance are uncertain. To provide a more coherent framework for future research, we have reviewed measurements in marine aerosol, the gas phase, and in rain. We also summarize sources and sinks, as well as model and laboratory studies of chemical transformations. The focus is on inorganic bromine over the open oceans, excluding the polar regions. The generation of sea-salt aerosol at the ocean surface is the major tropospheric source producing about 6.2 Tg/a of bromide. The transport of  Br from continents (as mineral aerosol, and as products from biomass-burning and fossil-fuel combustion can be of local importance. Transport of degradation products of long-lived Br-containing compounds from the stratosphere and other sources contribute lesser amounts. Available evidence suggests that, following aerosol acidification, sea-salt bromide reacts to form Br2 and BrCl that volatilize to the gas phase and photolyze in daylight to produce atomic Br and Cl. Subsequent transformations can destroy

  20. Determination of iodine and bromine in coal and atmospheric particles by inductively coupled plasma mass spectrometry.

    Science.gov (United States)

    Sun, Mingxing; Gao, Yunchuan; Wei, Biwen; Wu, Xiaowei

    2010-04-15

    Bromine and iodine in atmospheric particles or coal can cause environmental problems such as destruction of ozone in the atmosphere; therefore, the presence of these compounds has recently received increased attention. Here, a rapid and reliable method for the simultaneous determination of total bromine and iodine using ICP-MS analysis is described. Samples were dissolved in mixtures of 5 mL of HNO(3) and 2 mL of H(2)O(2) in a high pressure microwave digester. The solution was then oxidized by per-sulfate (Na(2)S(2)O(8)) in addition to a small amount of silver nitrate, after which the total bromine and iodine were measured simultaneously by ICP-MS. The signal memory effects of bromine and iodine during analysis were effectively decreased by washing with a new mixture agent (2% alcohol acidic solution, pH 1-2 adjusted with HCl). The detection limits for bromine and iodine using this method were about 3.2 microg L(-1) and 1.1 microg L(-1), respectively. Additionally, the spike recoveries were between 78.7% and 121% for bromine and iodine analysis, while the relative standard deviations ranged from 4.3% to 9.7%, and from 1.5% to 3.4% for bromine and iodine, respectively. The results of this study indicate that the method described here is suitable for the analysis of micro-amounts of bromine and iodine in atmospheric particles and coal samples.

  1. 40 CFR 721.775 - Brominated aromatic com-pound (generic name).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Brominated aromatic com-pound (generic name). 721.775 Section 721.775 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.775 Brominated aromatic com-pound (generic name). (a)...

  2. Distribution of bromine in mixed iodide-bromide organolead perovskites and its impact on photovoltaic performance

    NARCIS (Netherlands)

    Zhou, Yang; Wang, Feng; Fang, Hong-Hua; Loi, Maria Antonietta; Xie, Fang-Yan; Zhao, Ni; Wong, Ching-Ping

    2016-01-01

    Mixed iodide-bromide (I-Br) organolead perovskites are of great interest for both single junction and tandem solar cells since the optical bandgap of the materials can be tuned by varying the bromine to iodine ratio. Yet, it remains unclear how bromine incorporation modifies the properties of the pe

  3. Interplay of metals and bromine with dioxin-related compounds concentrated in e-waste open burning soil from Agbogbloshie in Accra, Ghana.

    Science.gov (United States)

    Fujimori, Takashi; Itai, Takaaki; Goto, Akitoshi; Asante, Kwadwo A; Otsuka, Masanari; Takahashi, Shin; Tanabe, Shinsuke

    2016-02-01

    Open burning of electronic waste (e-waste) releases various metals and organohalogen compounds in the environment. Here we investigated the interplay of metals (Cu, Pb, Zn, Fe, Co, and Sr) and bromine (Br) in the formation of dioxin-related compounds (DRCs), including polychlorinated dibenzo-p-dioxins/furans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs), as well as non-regulated DRCs such as polybrominated dibenzo-p-dioxins/furans (PBDD/Fs) and their monobrominated PCDD/Fs in soils sampled from open burning e-waste sites at Agbogbloshie in Accra, Ghana. The predominant DRCs were PBDFs, PCDFs, PCDDs, and DL-PCBs. Statistical analyzes, X-ray absorption spectroscopy, and the PCDF/PCDD ratio suggested possible formation paths of PCDD/Fs and DL-PCBs by catalytic behaviors of copper chlorides (CuCl, CuCl2, and Cu2(OH)3Cl) and thermal breakdown of polyvinyl chloride. Predominant formation of brominated furans may be derived from electron transfer from intermediates of PBDE to copper, Cu(II) → Cu(I). Lead chloride also contributed to generate DRCs and may become highly bioaccessible through the open burning of e-waste. The main zinc species (ZnCl2 and ZnS) suggested a possible relationship to generate DRCs and specific zinc source such as tire burning. Cu, Pb, Zn, and Br contained in various e-wastes, wires/cables, plastics, and tires strongly influenced generation of many DRCs.

  4. The Cyclotron Production and Nuclear Imaging of BROMINE-77.

    Science.gov (United States)

    Galiano, Eduardo

    In this investigation, bromine-77 was produced with a medical cyclotron and imaged with gamma cameras. Br -77 emits a 240 kev photon with a half life of 56 hours. The C-Br bond is stronger than the C-I bond and bromine is not collected in the thyroid. Bromine can be used to label many organic molecules by methods analogous to radioiodination. The only North American source of Br-77 in the 70's and 80's was Los Alamos National Laboratory, but it discontinued production in 1989. In this method, a p,3n reaction on Br-77 produces Kr-77 which decays with a 1.2 hour half life to Br-77. A cyclotron generated 40 MeV proton beam is incident on a nearly saturated NaBr or LiBr solution contained in a copper or titanium target. A cooling chamber through which helium gas is flowed separates the solution from the cyclotron beam line. Helium gas is also flowed through the solution to extract Kr-77 gas. The mixture flows through a nitrogen trap where Kr-77 freezes and is allowed to decay to Br-77. Eight production runs were performed, three with a copper target and five with a titanium target with yields of 40, 104, 180, 679, 1080, 685, 762 and 118 uCi respectively. Gamma ray spectroscopy has shown the product to be very pure, however corrosion has been a major obstacle, causing the premature retirement of the copper target. Phantom and in-vivo rat nuclear images, and an autoradiograph in a rat are presented. The quality of the nuclear scans is reasonable and the autoradiograph reveals high isotope uptake in the renal parenchyma, a more moderate but uniform uptake in pulmonary and hepatic tissue, and low soft tissue uptake. There is no isotope uptake in the brain or the gastric mucosa.

  5. Modelling chemistry over the Dead Sea: bromine and ozone chemistry

    OpenAIRE

    Smoydzin, L.; Glasow, R

    2009-01-01

    Measurements of O3 and BrO concentrations over the Dead Sea indicate that Ozone Depletion Events (ODEs), widely known to happen in polar regions, are also likely to occur over the Dead Sea due to the very high bromine content of the Dead Sea water. However, we show that BrO and O3 levels as they are detected cannot solely be explained by high Br levels in the Dead Sea water and the release of gas phase halogen...

  6. Environmental analysis of higher brominated diphenyl ethers and decabromodiphenyl ethane.

    Science.gov (United States)

    Kierkegaard, Amelie; Sellström, Ulla; McLachlan, Michael S

    2009-01-16

    Methods for environmental analysis of higher brominated diphenyl ethers (PBDEs), in particular decabromodiphenyl ether (BDE209), and the recently discovered environmental contaminant decabromodiphenyl ethane (deBDethane) are reviewed. The extensive literature on analysis of BDE209 has identified several critical issues, including contamination of the sample, degradation of the analyte during sample preparation and GC analysis, and the selection of appropriate detection methods and surrogate standards. The limited experience with the analysis of deBDethane suggests that there are many commonalities with BDE209. The experience garnered from the analysis of BDE209 over the last 15 years will greatly facilitate progress in the analysis of deBDethane.

  7. Deriving an atmospheric budget of total organic bromine using airborne in-situ measurements of brominated hydrocarbons in the Western Pacific during SHIVA

    Science.gov (United States)

    Sala, Stephan; Bönisch, Harald; Keber, Timo; Oram, Dave; Mills, Graham; Engel, Andreas

    2014-05-01

    Halogenated hydrocarbons play a major role as precursors for stratospheric ozone depletion. Released from the surface in the troposphere, the halocarbons reach the stratosphere via transport through the tropical tropopause layer. The contribution of the so called very short lived species (VSLS), having atmospheric lifetimes of less than half a year as sources gases for stratospheric bromine is significant. Source gas observations of long-lived bromine compounds and VSLS have so far not been able to explain the amount of bromine derived in the stratosphere from observations of BrO and modeling of the ratio of BrO to total bromine. Due to the short lifetimes and the high atmospheric variability, the representativeness of the available observations of VSLS source gases remains unclear, as these may vary with region and display seasonal variability. During the SHIVA (Stratospheric Ozone: Halogen Impacts in a Varying Atmosphere) project an extensive dataset with over 700 samples of ambient air of all halogen species relevant for the atmospheric budget of total organic bromine (long lived halocarbons: H-1301, H-1211, H-1202, H-2402 and CH3Br, very short lived substances: CHBr3, CH2Br2, CHBr2Cl, CHBrCl2 and CHBrCl) have been collected from onboard the FALCON aircraft in the West Pacific region. Measurements were performed with the newly developed fully-automated in-situ instrument GHOST-MS (Gas chromatograph for the Observation of Tracers - coupled with a Mass Spectrometer) by the Goethe University of Frankfurt and with the onboard whole-air sampler WASP with subsequent ground based state-of-the-art GC/MS analysis by the University of East Anglia. We will present the datasets, compare these to other observation, derive a bromine budget for the West Pacific and derive an estimate of the amount of bromine from VSLS reaching the stratosphere. Using the mean mixing ratios in the upper troposphere of the halocarbons mentioned above, the calculated budget of the total organic

  8. Effects of bromine on mitosis in root-tips of Allium cepa

    Energy Technology Data Exchange (ETDEWEB)

    Chury, J.; Slouka, V.

    1949-01-01

    The root-tips of Allium cepa, 1.5-2 cm. long, were exposed to pure bromine vapor for five minutes. The root-tips were then washed for ten minutes in water, and kept in fresh-water at a temperature of 20-24/sup 0/C. Squash preparations were made and stained according to the method of Darlington and La Cour. Bromine acting for five minutes on the root-tips of Allium has a specific effect on the cell nucleus in the resting stage. The effects induced are shown thirty-six hours after treatment by spindle abnormalities in metaphase and anaphase, and result in polyploidy in a large number of cells. Bromine produces chromosome and chromatid fragmentation; the latter may be followed by reunion. The effect of the bromine is cumulative and depends on the time which elapses between treatment and fixation. The cytological effects induced by bromine strongly suggest that it is another specific mutafacient chemical.

  9. Effect of bromine substituents in the formation of PXDD from poly halogenated phenols

    Energy Technology Data Exchange (ETDEWEB)

    Sakurai, T.; Ohono, T.; Weber, R.

    2002-07-01

    The condensation of chlorophenols has been studied extensively in the last two decades and was discussed as one mechanism in particular for the formation of PCDD in thermal processes. Brominated flame retardants and brominated and brominated-chlorinated dibenzodioxins and dibenzofurans have received increased attention recently due to the growing use of brominated flame retardants during the last decade. This is resulting than increase of brominated compounds in waste (e.g. Electric and electronic shredder waste), containing a considerable amount of bromine, in the form of brominated flame retardants. Many studies reported on the formation of PBDD/PBDF from brominated diphenylethers, or bromophenosl. However with the exception of Sodhu et al, a comparison of the condensation behaviour of bromophenols and chlorophenols was not done. The condensation of brominated phenols is interesting from several aspects. Bromophenols are used as flame retardants and might be a source of PBDD/F during thermal stress. Bromophenols can also be generated during the combustion/pyrolysis of bromodiphenylether or tetrabromobisphenol A containing material, serving as potential precursors for the formation of PBDD/PBDF. Further, in municipal waste incinerators with sufficient secondary combustion, the largest amount of chlorinated aromatic compounds (PCDD, PCDF, PCBs, PCNs, and chlorophenols) are formed in the cooling section (boiler, duct, dust filtration). Therefore in combustion processes involving high concentrations of brominated flame retardants, mixed PXDD/PXDF might be formed by condensation reactions of precursors or de novo synthesis in the cooling zone. Therefore we investigated the condensation of abrominated phenol in more detail and compare it to the condensation reaction of the analogous chlorophenol. (Author)

  10. Algae form brominated organic compounds in surface waters

    Energy Technology Data Exchange (ETDEWEB)

    Huetteroth, A.; Putschew, A.; Jekel, M. [Tech. Univ. Berlin (Germany)

    2004-09-15

    Monitoring of organic halogen compounds, measured as adsorbable organic bromine (AOBr) revealed seasonal high concentrations of organic bromine compounds in a surface water (Lake Tegel, Berlin, Germany). Usually, in late summer, concentrations are up to five times higher than during the rest of the year. The AOBr of the lake inflows (throughout the year less then 6 {mu}g/L) were always lower then those in the lake, which indicates a production of AOBr in the lake. A correlation of the AOBr and chlorophyll-a concentration (1) in the lake provides first evidence for the influence of phototrophic organisms. The knowledge of the natural production of organohalogens is relatively recent. Up to now there are more then 3800 identified natural organohalogen compounds that have been detected in marine plants, animals, and bacteria and also in terrestrial plants, fungi, lichen, bacteria, insects, some higher animals, and humans. Halogenated organic compounds are commonly considered to be of anthropogenic origin; derived from e.g. pharmaceuticals, herbicides, fungicides, insecticides, flame retardants, intermediates in organic synthesis and solvents. Additionally they are also produced as by-products during industrial processes and by waste water and drinking water disinfection. Organohalogen compounds may be toxic, persistent and/or carcinogenic. In order to understand the source and environmental relevance of naturally produced organobromine compounds in surface waters, the mechanism of the formation was investigated using batch tests with lake water and algae cultures.

  11. Impact of reactive bromine chemistry in the troposphere

    Directory of Open Access Journals (Sweden)

    R. von Glasow

    2004-01-01

    Full Text Available Recently several field campaigns and satellite observations have found strong indications for the presence of bromine oxide (BrO in the free troposphere. Using a global atmospheric chemistry transport model we show that BrO mixing ratios of a few tenths to 2 pmol mol-1 lead to a reduction in the zonal mean O3 mixing ratio of up to 18% in widespread areas and regionally up to 40% compared to a model run without bromine chemistry. A lower limit approach for the marine boundary layer, that does not explicitly include the release of halogens from sea salt aerosol, shows that for dimethyl sulfide (DMS the effect is even larger, with up to 60% reduction of its tropospheric column. This is accompanied by dramatic changes in DMS oxidation pathways, reducing its cooling effect on climate. In addition there are changes in the HO2:OH ratio that also affect NOx and PAN. These results imply that potentially significant strong sinks for O3 and DMS have so far been ignored in many studies of the chemistry of the troposphere.

  12. Maternal exposure to brominated flame retardants and infant Apgar scores.

    Science.gov (United States)

    Terrell, Metrecia L; Hartnett, Kathleen P; Lim, Hyeyeun; Wirth, Julie; Marcus, Michele

    2015-01-01

    Brominated flame retardants (BFRs) and other persistent organic pollutants have been associated with adverse health outcomes in humans and may be particularly toxic to the developing fetus. We investigated the association between in utero polybrominated biphenyl (PBB) and polychlorinated biphenyl (PCB) exposures and infant Apgar scores in a cohort of Michigan residents exposed to PBB through contaminated food after an industrial accident. PBB and PCB concentrations were measured in serum at the time the women were enrolled in the cohort. PBB concentrations were also estimated at the time of conception for each pregnancy using a validated elimination model. Apgar scores, a universal measure of infant health at birth, measured at 1 and 5min, were taken from birth certificates for 613 offspring born to 330 women. Maternal PCB concentrations at enrollment were not associated with below-median Apgar scores in this cohort. However, maternal PBB exposure was associated with a dose-related increase in the odds of a below-median Apgar score at 1min and 5min. Among infants whose mothers had an estimated PBB at conception above the limit of detection of 1 part per billion (ppb) to Apgar score increased with higher maternal PBB at conception. It remains critical that future studies examine possible relationships between in utero exposures to brominated compounds and adverse health outcomes.

  13. Bromine Chemistry in the Tropical UTLS during the 2011, 2013 and 2014 ATTREX Experiments

    Science.gov (United States)

    Werner, Bodo; Stutz, Jochen; Spolaor, Max; Festa, James; Tsai, Catalina; Colosimo, Fedele; Cheung, Ross; Deutschmann, Tim; Raecke, Rasmus; Scalone, Lisa; Tricoli, Ugo; Pfeilsticker, Klaus; Navarro, Maria; Atlas, Elliot; Chipperfield, Martyn; Hossaini, Ryan

    2015-04-01

    Bromine plays an important role for the chemistry of ozone in the stratosphere and upper troposphere. An accurate quantitative understanding of the sources, sinks, and chemical transformation of bromine species is thus important to understand the bromine budget in the upper troposphere and lower stratosphere (UTLS), which also serves as a gate to the stratosphere. Vertical transport of very short-lived organic bromine precursors and inorganic product gases has been identified as the main source of bromine in the UTLS. However, the contribution of inorganic vs. organic compounds is not well quantified, particularly in the tropical UTLS. A limb scanning Differential Optical Absorption Spectroscopy instrument was deployed onboard NASA's UAV Global Hawk during the NASA Airborne Tropical TRopopause EXperiment (ATTREX) during a series of flights into the eastern and western Pacific tropopause layer (flight altitudes up to 18 km), which is a gateway to the stratosphere. The measurement methodology to retrieve vertical trace gas concentration profiles will be briefly presented. Observations of BrO, NO2 and O3 and of other trace species, in particular of brominated hydrocarbons are compared with simulations of the SLIMCAT CTM and interpreted with respect to photochemistry and the budget of bromine within the tropical tropopause layer (TTL).

  14. Conversion of bromine during thermal decomposition of printed circuit boards at high temperature.

    Science.gov (United States)

    Jin, Yu-qi; Tao, Lin; Chi, Yong; Yan, Jian-hua

    2011-02-15

    The conversion of bromine during the thermal decomposition of printed circuit boards (PCBs) was investigated at isothermal temperatures ranging from 800°C to 1100°C by using a quartz tube furnace. The influence of temperature, oxygen concentrations (0%, 10% and 21% in the nitrogen-oxygen atmosphere) and content of steam on conversion of bromine was studied. With the increment of temperature, the conversion from organic bromine in the PCBs to inorganic bromine in the gaseous fraction increased from 69.0% to 96.4%. The bromine was mainly evolved as HBr and Br(2) in oxidizing condition and the Br(2)/HBr mass ratio increased at stronger oxidizing atmosphere. The experimental results also indicated that the existence of steam can reduce the formation of Br(2). Furthermore, co-combustion of PCBs with S and CaO, both as addition agents, was investigated, respectively. In the presence of SO(2), Br(2)/HBr mass ratio obviously decreased. Moreover, the utilization of calcium oxide can efficiently promote the conversion of organic bromine to inorganic bromine. According to the experimental results, incinerating PCBs at high temperature can efficiently destroy the organobrominated compounds that are considered to be possible precursors of polybrominated dibenzeo-p-dioxins and dibenzofurans (PBDD/Fs), but the Br(2) and HBr in flue gas should be efficiently controlled.

  15. The contribution of anthropogenic bromine emissions to past stratospheric ozone trends: a modelling study

    Directory of Open Access Journals (Sweden)

    B.-M. Sinnhuber

    2009-04-01

    Full Text Available Bromine compounds play an important role in the depletion of stratospheric ozone. We have calculated the changes in stratospheric ozone in response to changes in the halogen loading over the past decades, using a two-dimensional (latitude/height model constrained by source gas mixing ratios at the surface. Model calculations of the decrease of total column ozone since 1980 agree reasonably well with observed ozone trends, in particular when the contribution from very short-lived bromine compounds is included. Model calculations with bromine source gas mixing ratios fixed at 1959 levels, corresponding approximately to a situation with no anthropogenic bromine emissions, show an ozone column reduction between 1980 and 2005 at Northern Hemisphere mid-latitudes of only ≈55% compared to a model run including all halogen source gases. In this sense anthropogenic bromine emissions are responsible for ≈45% of the model estimated column ozone loss at Northern Hemisphere mid-latitudes. However, since a large fraction of the bromine induced ozone loss is due to the combined BrO/ClO catalytic cycle, the effect of bromine would have been smaller in the absence of anthropogenic chlorine emissions. The chemical efficiency of bromine relative to chlorine for global total ozone depletion from our model calculations, expressed by the so called α-factor, is 64 on an annual average. This value is much higher than previously published results. Updates in reaction rate constants can explain only part of the differences in α. The inclusion of bromine from very short-lived source gases has only a minor effect on the global mean α-factor.

  16. Brominated lipids identify lipid binding sites on the surface of the reaction center from Rhodobacter sphaeroides.

    Science.gov (United States)

    Roszak, Aleksander W; Gardiner, Alastair T; Isaacs, Neil W; Cogdell, Richard J

    2007-03-20

    This study describes the use of brominated phospholipids to distinguish between lipid and detergent binding sites on the surface of a typical alpha-helical membrane protein. Reaction centers isolated from Rhodobacter sphaeroides were cocrystallized with added brominated phospholipids. X-ray structural analysis of these crystals has revealed the presence of two lipid binding sites from the characteristic strong X-ray scattering from the bromine atoms. These results demonstrate the usefulness of this approach to mapping lipid binding sites at the surface of membrane proteins.

  17. Influence of Main Components in Exhaust Gas on Mercury Adsorption Capacity of Brominated Activated Carbon

    Directory of Open Access Journals (Sweden)

    Tran Hong Con

    2016-01-01

    Full Text Available Brominated activated carbon (AC-Br, which was produced from coconut shell activated carbon (AC and brominated by wet way with elemental bromine, was determined as a material with super high adsorption capacity of mercury vapor. But in real exhaust gases, there are many components such as SO2, NOx, CO, CO2, HCl, H2O can influence on adsorption ability of the AC-Br. In this paper, these influences were studied and compared them between initial AC and AC-Br. Each component has different effect on AC and AC-Br and followed by its particular mechanism.

  18. Benzalkonium Chloride and Glaucoma

    OpenAIRE

    Rasmussen, Carol A.; Kaufman, Paul L.; Kiland, Julie A.

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapo...

  19. Selective nitration and bromination of surprisingly ruffled phosphorus corroles.

    Science.gov (United States)

    Pomarico, Giuseppe; Tortora, Luca; Fronczek, Frank R; Smith, Kevin M; Paolesse, Roberto

    2016-05-01

    Phosphorus complexes of corrole have recently attracted increasing interest since these compounds can be easily prepared in good yields, are stable, and show unusual optical properties. For these reasons, phosphorus corroles represent a class of interesting compounds to be exploited in the field of material science or for biomedical investigations and the definition of synthetic pathways for their functionalization is an important step to optimize their properties for various applications. We report here the reactivity of the phosphorus complex of 5,10,15-tritolylcorrole in the nitration or bromination reaction. Both these attempts were successful, allowing the preparation of substituted phosphorus corroles, which can be used as intermediates of more complex architectures endowed with useful properties. Furthermore, the crystallographic characterization of both complexes shows that they have an unusual ruffled geometry of the corrole core, a conformation that has not been considered possible for such a macrocycle.

  20. Diamagnetic Raman Optical Activity of Chlorine, Bromine, and Iodine Gases.

    Science.gov (United States)

    Šebestík, Jaroslav; Kapitán, Josef; Pačes, Ondřej; Bouř, Petr

    2016-03-01

    Magnetic Raman optical activity of gases provides unique information about their electric and magnetic properties. Magnetic Raman optical activity has recently been observed in a paramagnetic gas (Angew. Chem. Int. Ed. 2012, 51, 11058; Angew. Chem. 2012, 124, 11220). In diamagnetic molecules, it has been considered too weak to be measurable. However, in chlorine, bromine and iodine vapors, we could detect a significant signal as well. Zeeman splitting of electronic ground-state energy levels cannot rationalize the observed circular intensity difference (CID) values of about 10(-4). These are explicable by participation of paramagnetic excited electronic states. Then a simple model including one electronic excited state provides reasonable spectral intensities. The results suggest that this kind of scattering by diamagnetic molecules is a general event observable under resonance conditions. The phenomenon sheds new light on the role of excited states in the Raman scattering, and may be used to probe molecular geometry and electronic structure.

  1. The third international interlaboratory study on brominated flame retardants

    Energy Technology Data Exchange (ETDEWEB)

    Boer, J. de [Netherlands Institute for Fisheries Research, IJmuiden (Netherlands); Wells, D. [FRS Marine Laboratory, Aberdeen (United Kingdom)

    2004-09-15

    Polybrominated diphenyl ethers (PBDEs) have been produced as brominated flame retardants (BFRs) since the early 1970s and have been found in the aquatic environment since the late 1970s. However, as a result of their detection in sperm whales from deeper Atlantic waters and in human milk, many laboratories are now measuring PBDEs in environmental samples. A first international interlaboratory study (ILS) on the analysis of PBDEs, organised by the Bromine Science and Environmental Forum (BSEF), Brussels, Belgium, in collaboration with the Netherlands Institute for Fisheries Research (RIVO) was conducted in 1999-2000. The results showed that the 18 participating laboratories produced comparable results for BDE 47 in various matrices but had analytical difficulties for other BDEs, in particular for the BDEs 99 and 209. A second study was organised in 2001-2002 by BSEF, QUASIMEME and RIVO. That study showed improvement in comparability of the participating laboratories for BDE99 and some other BDEs. However, there was no improvement for BDE209. Hexabromocyclododecane (HBCD), tetrabromobisphenol-A (TBBP-A) and the dimethyl derivative of TBBP-A (dimethyl TBBP-A) were included in the second study. However, it appeared that only two or three laboratories were able to analyse these determinands. Others laboratories were still in the development phase with their methods for these BFRs. This third study was organised as a development exercise by QUASIMEME, in collaboration with RIVO between September and December 2003. The BFRs selected were the same as in the second study. Two biota test materials, a harbor sediment, a sewage sludge, and two standard solutions were dispatched to the participants.

  2. Potent competitive interactions of some brominated flame retardants and related compounds with human transthyretin in vitro

    NARCIS (Netherlands)

    Meerts, I.A.T.M.; Zanden, van J.J.; Luijks, E.A.C.; Leeuwen-Bol, van I.; Marsh, G.; Jakobsson, E.; Bergman, A.; Brouwer, A.

    2000-01-01

    Brominated flame retardants such as polybrominated diphenyl ethers (PBDEs), pentabromophenol (PBP), and tetrabromobisphenol A (TBBPA) are produced in large quantities for use in electronic equipment, plastics, and building materials. Because these compounds have some structural resemblance to the th

  3. Oxidation of mercury by bromine in the subtropical Pacific free troposphere

    Science.gov (United States)

    Gratz, L. E.; Ambrose, J. L.; Jaffe, D. A.; Shah, V.; Jaeglé, L.; Stutz, J.; Festa, J.; Spolaor, M.; Tsai, C.; Selin, N. E.; Song, S.; Zhou, X.; Weinheimer, A. J.; Knapp, D. J.; Montzka, D. D.; Flocke, F. M.; Campos, T. L.; Apel, E.; Hornbrook, R.; Blake, N. J.; Hall, S.; Tyndall, G. S.; Reeves, M.; Stechman, D.; Stell, M.

    2015-12-01

    Mercury is a global toxin that can be introduced to ecosystems through atmospheric deposition. Mercury oxidation is thought to occur in the free troposphere by bromine radicals, but direct observational evidence for this process is currently unavailable. During the 2013 Nitrogen, Oxidants, Mercury and Aerosol Distributions, Sources and Sinks campaign, we measured enhanced oxidized mercury and bromine monoxide in a free tropospheric air mass over Texas. We use trace gas measurements, air mass back trajectories, and a chemical box model to confirm the origin and chemical history of the sampled air mass. We find the presence of elevated oxidized mercury to be consistent with oxidation of elemental mercury by bromine atoms in this subsiding upper tropospheric air mass within the subtropical Pacific High, where dry atmospheric conditions are conducive to oxidized mercury accumulation. Our results support the role of bromine as the dominant oxidant of mercury in the upper troposphere.

  4. Potent anti-inflammatory activity of novel microtubule-modulating brominated noscapine analogs.

    Science.gov (United States)

    Zughaier, Susu; Karna, Prasanthi; Stephens, David; Aneja, Ritu

    2010-02-11

    Noscapine, a plant-derived, non-toxic, over-the-counter antitussive alkaloid has tubulin-binding properties. Based upon the structural resemblance of noscapine to colchicine, a tubulin-binding anti-inflammatory drug, noscapine and its semi-synthetic brominated analogs were examined for in vitro anti-inflammatory activity. Brominated noscapine analogs were found to inhibit cytokine and chemokine release from macrophage cell lines but did not affect cell viability. Brominated noscapine analogs demonstrated anti-inflammatory properties in both TLR- and non-TLR induced in vitro innate immune pathway inflammation models, mimicking septic and sterile infection respectively. In addition, electron microscopy and immunoblotting data indicated that these analogs induced robust autophagy in human macrophages. This study is the first report to identify brominated noscapines as innate immune pathway anti-inflammatory molecules.

  5. Potent anti-inflammatory activity of novel microtubule-modulating brominated noscapine analogs.

    Directory of Open Access Journals (Sweden)

    Susu Zughaier

    Full Text Available Noscapine, a plant-derived, non-toxic, over-the-counter antitussive alkaloid has tubulin-binding properties. Based upon the structural resemblance of noscapine to colchicine, a tubulin-binding anti-inflammatory drug, noscapine and its semi-synthetic brominated analogs were examined for in vitro anti-inflammatory activity. Brominated noscapine analogs were found to inhibit cytokine and chemokine release from macrophage cell lines but did not affect cell viability. Brominated noscapine analogs demonstrated anti-inflammatory properties in both TLR- and non-TLR induced in vitro innate immune pathway inflammation models, mimicking septic and sterile infection respectively. In addition, electron microscopy and immunoblotting data indicated that these analogs induced robust autophagy in human macrophages. This study is the first report to identify brominated noscapines as innate immune pathway anti-inflammatory molecules.

  6. In vitro screening of the endocrine disrupting potency of brominated flame retardants and their metabolites

    NARCIS (Netherlands)

    Hamers, T.H.M.; Kamstra, J.H.; Sonneveld, E.; Murk, A.J.; Zegers, B.N.; Boon, J.P.; Brouwer, A.

    2004-01-01

    DEVELOPMENTAL AND REPRODUCTIVE TOXICITY vitro screening the endocrine disrupting potency brominated flame retardants and their metabolites Timo Hamers Jorke Kamstra Edwin Sonneveld Albertinka Murk Bart Zegers Jan Boon Abraham Brouwer Institute for Environmental Studies IVM Amsterdam BioDetection Sys

  7. A Novel Protocol for the Regioselective Bromination of Primary Alcohols in Unprotected Carbohydrates or Glycosides

    Institute of Scientific and Technical Information of China (English)

    薛伟华; 张立芬

    2012-01-01

    The regioselective and efficient bromination of primary hydroxyl groups in unprotected carbohydrates or glycosides is successfully achieved by using (chloro-phenylthio-methylene)dimethylammoniumchloride (CPMA) in the presence of tetrabutylammonium bromide (TBAB) in dry DMF.

  8. Dynamic dielectric properties and the γ transition of bromine doped polyacrylonitrile

    Directory of Open Access Journals (Sweden)

    2007-10-01

    Full Text Available Based on monitoring the γ process (the lowest temperature-relaxation in polyacrylonitrile (PAN by dynamic dielectric spectroscopy, new evidence for the formation of a charge transfer complex between bromine dopants and nitrile groups is presented. The experimental work is carried out on PAN and nitrile polymerized PAN with and without bromine doping and the effects of these factors on the γ process are measured. Nitrile polymerization results in diminishing of the γ process and in a 15% increase in its activation energy, whereas bromine doping produces splitting of the original γ process in PAN – coupled with a significant activation energy increase – and its complete disappearance in nitrile polymerized PAN. Both the splitting of the γ process and the higher activation energy reflect bromine-nitrile adduct formation..

  9. Evaluation of carbon cryogels used as cathodes for non-flowing zinc-bromine storage cells

    Energy Technology Data Exchange (ETDEWEB)

    Ayme-Perrot, David; Walter, Serge; Gabelica, Zelimir [Groupe Securite et Ecologie Chimiques (GSEC), ENSCMu, 3 rue Alfred Werner, F-68093 Mulhouse Cedex (France); Valange, Sabine [Laboratoire de Catalyse en Chimie Organique (LACCO), ESIP, 40 Avenue du Recteur Pineau, F-86022 Poitiers Cedex (France)

    2008-01-03

    Monolithic megaloporous carbon cryogels were examined for their potential applications as cathodic electrodes in secondary zinc-bromine cells. This work investigates the possibility of using their particular macroporous texture as microscopic bromine tanks in a zinc/bromine battery. The electrochemical behaviour of a cell based upon such a Br{sub 2} electrode was studied and discussed in terms of energy yields, energy storage capability and cycle life. Good storages (over 20 Wh kg{sup -1}) could be obtained during the first 2 h of cell charging for currents between 10 and 20 mA g{sup -1}. The energy yield remains almost constant during a fairly large number of cycles, basically for weak charges (e.g. 25 C g{sup -1}). Our findings show that the good cyclability of the cathodic electrode is a consequence of the liquid state of the active bromine phase. (author)

  10. New insight into photo-bromination processes in saline surface waters: The case of salicylic acid

    Energy Technology Data Exchange (ETDEWEB)

    Tamtam, Fatima; Chiron, Serge, E-mail: serge.chiron@msem.univ-montp2.fr

    2012-10-01

    It was shown, through a combination of field and laboratory observations, that salicylic acid can undergo photo-bromination reactions in sunlit saline surface waters. Laboratory-scale experiments revealed that the photochemical yields of 5-bromosalicylic acid and 3,5-dibromosalicylic acid from salicylic acid were always low (in the 4% range at most). However, this might be of concern since these compounds are potential inhibitors of the 20{alpha}-hydroxysteroid dehydrogenase enzyme, with potential implications in endocrine disruption processes. At least two mechanisms were involved simultaneously to account for the photo-generation of brominated substances. The first one might involve the formation of reactive brominated radical species (Br{center_dot}, Br{sub 2}{center_dot}{sup -}) through hydroxyl radical mediated oxidation of bromide ions. These ions reacted more selectively than hydroxyl radicals with electron-rich organic pollutants such as salicylic acid. The second one might involve the formation of hypobromous acid, through a two electron oxidation of bromine ions by peroxynitrite. This reaction was catalyzed by nitrite, since these ions play a crucial role in the formation of nitric oxide upon photolysis. This nitric oxide further reacts with superoxide radical anions to yield peroxynitrite and by ammonium through the formation of N-bromoamines, probably due to the ability of N-bromoamines to promote the aromatic bromination of phenolic compounds. Field measurements revealed the presence of salicylic acid together with 5-bromosalicylic and 3,5-dibromosalicylic acid in a brackish coastal lagoon, thus confirming the environmental significance of the proposed photochemically induced bromination pathways. -- Highlights: Black-Right-Pointing-Pointer Brominated derivatives of salicylic acid were detected in a brackish lagoon. Black-Right-Pointing-Pointer A photochemical pathway was hypothesized to account for bromination of salicylic acid. Black

  11. Bromine-lithium exchange: An efficient tool in the modular construction of biaryl ligands.

    Science.gov (United States)

    Bonnafoux, Laurence; Leroux, Frédéric R; Colobert, Françoise

    2011-01-01

    Regioselective bromine-lithium exchange reactions on polybrominated biaryls enable the modular synthesis of various polysubstituted biphenyls such as bis(dialkylphosphino)-, bis(diarylphosphino)- and dialkyl(diaryl)phosphinobiphenyls. All permutations of substituents at the ortho positions of the biphenyls are possible. In a similar manner, one can gain access to monophosphine analogues. So far, such a process, based on the effective discrimination between bromine atoms as a function of their chemical environment, has been observed only sporadically.

  12. Gaia Paradigm: A Biotic Origin Of The Polar Sunrise Arctic Bromine Explosion

    OpenAIRE

    Iudin, M.

    2008-01-01

    The main attention is given to discussion of the natural causes and regularities of the Arctic bromine pollution. We make notice of marine microbial organisms and their metabolism as a prime driving force for the elemental biogeochemical cycles. One of the important conclusions of this study is on similarity between ocean bromine concentrating as by-product of the marine microbial activities and nitrogen fixation by soil bacteria. In both cases, microbial organisms and their food webs maintai...

  13. Surface Response of Brominated Carbon Media on Laser and Thermal Excitation: Optical and Thermal Analysis Study

    Science.gov (United States)

    Multian, Volodymyr V.; Kinzerskyi, Fillip E.; Vakaliuk, Anna V.; Grishchenko, Liudmyla M.; Diyuk, Vitaliy E.; Boldyrieva, Olga Yu.; Kozhanov, Vadim O.; Mischanchuk, Oleksandr V.; Lisnyak, Vladyslav V.; Gayvoronsky, Volodymyr Ya.

    2017-02-01

    The present study is objected to develop an analytical remote optical diagnostics of the functionalized carbons surface. Carbon composites with up to 1 mmol g-1 of irreversibly adsorbed bromine were produced by the room temperature plasma treatment of an activated carbon fabric (ACF) derived from polyacrylonitrile textile. The brominated ACF (BrACF) was studied by elastic optical scattering indicatrix analysis at wavelength 532 nm. The obtained data were interpreted within results of the thermogravimetric analysis, X-ray photoelectron spectroscopy and temperature programmed desorption mass spectrometry. The bromination dramatically reduces the microporosity producing practically non-porous material, while the incorporated into the micropores bromine induces the dielectric and structural impact on surface polarizability and conductivity due to the charging effect. We have found that the elastic optical scattering in proper solid angles in the forward and the backward hemispheres is sensitive to the kind of the bromine bonding, e.g., physical adsorption or chemisorption, and the bromination level, respectively, that can be utilized for the express remote fabrication control of the nanoscale carbons with given interfaces.

  14. Photothermally induced bromination of carbon/polymer bipolar plate materials for fuel cell applications

    Energy Technology Data Exchange (ETDEWEB)

    Schade, Martin; Franzka, Steffen [Fakultät für Chemie, Universität Duisburg-Essen, 45117 Essen (Germany); Center for Nanointegration Duisburg-Essen (CENIDE), University of Duisburg-Essen, Carl-Benz-Straße 199, 47057 Duisburg (Germany); Cappuccio, Franco; Peinecke, Volker; Heinzel, Angelika [Center for Nanointegration Duisburg-Essen (CENIDE), University of Duisburg-Essen, Carl-Benz-Straße 199, 47057 Duisburg (Germany); Zentrum für BrennstoffzellenTechnik (ZBT), Carl-Benz-Straße 201, 47057 Duisburg (Germany); Hartmann, Nils, E-mail: nils.hartmann@uni-due.de [Fakultät für Chemie, Universität Duisburg-Essen, 45117 Essen (Germany); Center for Nanointegration Duisburg-Essen (CENIDE), University of Duisburg-Essen, Carl-Benz-Straße 199, 47057 Duisburg (Germany)

    2015-05-01

    Graphical abstract: - Highlights: • Photothermal laser bromination of carbon/polymer materials is demonstrated. • Using a microfocused laser functionalized domains with diameters of 5 μm and 100 μm and more can be fabricated. • Bromine groups can be transformed in a variety of other chemical functionalities, i.e. amine groups. • Depending on the chemical functionality, the local chemical affinity and wettability is changed. • The routine can be applied to standard bipolar plate materials used for fuel cell applications. - Abstract: A facile photothermal procedure for direct functionalization of carbon/polymer bipolar plate materials is demonstrated. Through irradiation with a microfocused beam of an Ar{sup +}-laser at λ = 514 nm in gaseous bromine and distinct laser powers and pulse lengths local bromination of the carbon/polymer material takes place. At a 1/e spot diameter of 2.1 μm, functionalized surface areas with diameters down to 5 μm are fabricated. In complementary experiments large-area bromination is investigated using an ordinary tungsten lamp. For characterization contact angle goniometry, X-ray photoelectron spectroscopy and electron microscopy in conjunction with labeling techniques are employed. After irradiation bromine groups can easily be substituted by other chemical functionalities, e.g. azide and amine groups. This provides a facile approach in order to fabricate surface patterns and gradient structures with varying wetting characteristics. Mechanistic aspects and prospects of photothermal routines in micropatterning of carbon/polymer materials are discussed.

  15. Oxomemazine hydro-chloride.

    Science.gov (United States)

    Siddegowda, M S; Butcher, Ray J; Akkurt, Mehmet; Yathirajan, H S; Ramesh, A R

    2011-08-01

    IN THE TITLE COMPOUND [SYSTEMATIC NAME: 3-(5,5-dioxo-phen-othia-zin-10-yl)-N,N,2-trimethyl-propanaminium chloride], C(18)H(23)N(2)O(2)S(+)·Cl(-), the dihedral angle between the two outer aromatic rings of the phenothia-zine unit is 30.5 (2)°. In the crystal, the components are linked by N-H⋯Cl and C-H⋯Cl hydrogen bonds and C-H⋯π inter-actions.

  16. XPS STUDIES ON SURFACE MODIFIED POLY[1-(TRIMETHYLSILYL)-1-PROPYNE] MEMBRANES Ⅱ SURFACE MODIFICATION BY BROMINE VAPOR

    Institute of Scientific and Technical Information of China (English)

    XU Guanfan; SUN Xiaoguang; QIU Xuepeng; ZHANG Jinlan; ZHENG Guodong

    1994-01-01

    Surface modification of poly [ 1-(trimethylsilyl )-1-propyne ] ( PTMSP ) membranes by bromine vapor has been studied. It is shown that Br/C atomic ratio at the surfacesincreased with the time of bromination until about 60 min, then it reached a plateau. The results of XPS and IR studies indicated that the addition of bromine to double bonds and the replacement of H on CH3 by bromine had taken place so that a new peak at 286.0 eV (C-Br)in C1sspectra and some new bands, e. g. at 1220 and 580cm-1,in IR spectra were formed. The fact, Po2, permeability of oxygen, decreased and αO2/N2, separation factor of oxygen relative to nitrogen, increased with bromination time, shows that surface modification of PTMSP by bromine may be an efficient approachto prepare PTMSP membranes used for practical gas separations.

  17. Bromine partitioning between olivine and melt at OIB source conditions: Indication for volatile recycling

    Science.gov (United States)

    Joachim, Bastian; Ruzié, Lorraine; Burgess, Ray; Pawley, Alison; Clay, Patricia L.; Ballentine, Christopher J.

    2016-04-01

    Halogens play a key role in our understanding of volatile transport processes in the Earth's mantle. Their moderate (fluorine) to highly (iodine) incompatible and volatile behavior implies that their distribution is influenced by partial melting, fractionation and degassing processes as well as fluid mobilities. The heavy halogens, particularly bromine and iodine, are far more depleted in the Earth's mantle than expected from their condensation temperature (Palme and O'Neill 2014), so that their very low abundances in basalts and peridotites (ppb-range) make it analytically challenging to investigate their concentrations in Earth's mantle reservoirs and their behavior during transport processes (Pyle and Mather, 2009). We used a new experimental technique, which combines the irradiation technique (Johnson et al. 2000), laser ablation and conventional mass spectrometry. This enables us to present the first experimentally derived bromine partition coefficient between olivine and melt. Partitioning experiments were performed at 1500° C and 2.3 GPa, a P-T condition that is representative for partial melting processes in the OIB source region (Davis et al. 2011). The bromine partition coefficient between olivine and silicate melt at this condition has been determined to DBrol/melt = 4.37•10-4± 1.96•10-4. Results show that bromine is significantly more incompatible than chlorine (˜1.5 orders of magnitude) and fluorine (˜2 orders of magnitude) due to its larger ionic radius. We have used our bromine partitioning data to estimate minimum bromine abundances in EM1 and EM2 source regions. We used minimum bromine bulk rock concentrations determined in an EM1 (Pitcairn: 1066 ppb) and EM2 (Society: 2063 ppb) basalt (Kendrick et al. 2012), together with an estimated minimum melt fraction of 0.01 in OIB source regions (Dasgupta et al. 2007). The almost perfect bromine incompatibility results in minimum bromine abundances in EM1 and EM2 OIB source regions of 11 ppb and 20

  18. An exemplary case of a bromine explosion event linked to cyclone development in the Arctic

    Science.gov (United States)

    Blechschmidt, A.-M.; Richter, A.; Burrows, J. P.; Kaleschke, L.; Strong, K.; Theys, N.; Weber, M.; Zhao, X.; Zien, A.

    2016-02-01

    Intense, cyclone-like shaped plumes of tropospheric bromine monoxide (BrO) are regularly observed by GOME-2 on board the MetOp-A satellite over Arctic sea ice in polar spring. These plumes are often transported by high-latitude cyclones, sometimes over several days despite the short atmospheric lifetime of BrO. However, only few studies have focused on the role of polar weather systems in the development, duration and transport of tropospheric BrO plumes during bromine explosion events. The latter are caused by an autocatalytic chemical chain reaction associated with tropospheric ozone depletion and initiated by the release of bromine from cold brine-covered ice or snow to the atmosphere. In this manuscript, a case study investigating a comma-shaped BrO plume which developed over the Beaufort Sea and was observed by GOME-2 for several days is presented. By making combined use of satellite data and numerical models, it is shown that the occurrence of the plume was closely linked to frontal lifting in a polar cyclone and that it most likely resided in the lowest 3 km of the troposphere. In contrast to previous case studies, we demonstrate that the dry conveyor belt, a potentially bromine-rich stratospheric air stream which can complicate interpretation of satellite retrieved tropospheric BrO, is spatially separated from the observed BrO plume. It is concluded that weather conditions associated with the polar cyclone favoured the bromine activation cycle and blowing snow production, which may have acted as a bromine source during the bromine explosion event.

  19. Antimicrobial N-brominated hydantoin and uracil grafted polystyrene beads.

    Science.gov (United States)

    Farah, Shady; Aviv, Oren; Laout, Natalia; Ratner, Stanislav; Domb, Abraham J

    2015-10-28

    Hydantoin-N-halamine derivatives conjugated on polystyrene beads are promising disinfectants with broad antimicrobial activity affected by the gradual release of oxidizing halogen in water. The objective of this work was to identify and test of hydantoin-like molecules possessing urea moiety, which may provide N-haloamines releasing oxidizing halogens when exposed to water at different rates and release profiles for tailored antimicrobial agents. In this work, several hydantoin (five member ring) and for the first time reported, uracil (six member ring) derivatives have been conjugated to polystyrene beads and tested for their lasting antimicrobial activity. Four molecules of each series were conjugated onto polystyrene beads from the reaction of the N-potassium hydantoin or uracil derivatives onto chloromethylated polystyrene beads. A distinct difference in bromine loading capacity and release profiles was found for the different conjugated derivatives. All tested materials exhibit strong antimicrobial activity against Escherichia coli and bacteriophages MS2 of 7 and ~4 log reduction, respectively. These results highlight the antimicrobial potential of halogenated cyclic molecules containing urea groups as water disinfection agents.

  20. Modelling chemistry over the Dead Sea: bromine and ozone chemistry

    Directory of Open Access Journals (Sweden)

    R. von Glasow

    2009-07-01

    Full Text Available Measurements of O3 and BrO concentrations over the Dead Sea indicate that Ozone Depletion Events (ODEs, widely known to happen in polar regions, are also occuring over the Dead Sea due to the very high bromine content of the Dead Sea water. However, we show that BrO and O3 levels as they are detected cannot solely be explained by high Br levels in the Dead Sea water and the release of gas phase halogen species out of sea borne aerosol particles and their conversion to reactive halogen species. It is likely that other sources for reactive halogen compounds are needed to explain the observed concentrations for BrO and O3. To explain the chemical mechanism taking place over the Dead Sea leading to BrO levels of several pmol/mol we used the one-dimensional model MISTRA which calculates microphysics, meteorology, gas and aerosol phase chemistry. We performed pseudo Lagrangian studies by letting the model column first move over the desert which surrounds the Dead Sea region and then let it move over the Dead Sea itself. To include an additional source for gas phase halogen compounds, gas exchange between the Dead Sea water and the atmosphere is treated explicitly. Model calculations indicate that this process has to be included to explain the measurements.

  1. Brominated flame retardants in Belgian little owl (Athene noctua) eggs

    Energy Technology Data Exchange (ETDEWEB)

    Jaspers, V.; Covaci, A.; Maervoet, J.; Dauwe, T.; Schepens, P.; Eens, M. [Antwerp Univ. (Belgium)

    2004-09-15

    Since the 1960s, polybrominated diphenylethers (PBDEs), a class of brominated flame retardants (BFRs), are widely used in textiles, plastics, electronic equipment and other materials. Their massive use has led to the ubiquitous presence of PBDEs in the environment and in biota in which the PBDE levels seem to increase rapidly. High concentrations of some congeners may cause adverse effects in both wildlife and in human populations1 and this has led to the growing concern of scientists over the last decade and to the need for more data on environmental levels of PBDEs. The little owl (Athene noctua) is a small sedentary predator, which makes it a very suitable biomonitoring species. This owl species feeds on a variety of preys, including small mammals and birds, reptiles, amphibians, earthworms and beetles, depending on the season and the local circumstances. Because very limited information is available about contamination levels in the little owl, a study was conducted to determine the concentrations of PBDEs, polybrominated biphenyls (PBBs), polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in deserted or addled eggs of little owls in Belgium. Eggs have been used successfully as a monitoring tool for persistent organic pollutants (POPs) in several studies. Although the analysis of POPs in deserted or addled eggs has clear limitations, these can be partially avoided by analysing only highly persistent components, for which the original composition will not change due to 'posthatching' microbiological degradation.

  2. Benzalkonium chloride and glaucoma.

    Science.gov (United States)

    Rasmussen, Carol A; Kaufman, Paul L; Kiland, Julie A

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapoptosis, cytoskeleton changes, and immunoinflammatory reactions. These same effects have been reported in cultured human TM cells exposed to concentrations of BAK found in common glaucoma drugs and in the TM of primary open-angle glaucoma donor eyes. It is possible that a relationship exists between chronic exposure to BAK and glaucoma. The hypothesis that BAK causes/worsens glaucoma is being tested experimentally in an animal model that closely reflects human physiology.

  3. Chloride on the Move

    KAUST Repository

    Li, Bo

    2017-01-09

    Chloride (Cl−) is an essential plant nutrient but under saline conditions it can accumulate to toxic levels in leaves; limiting this accumulation improves the salt tolerance of some crops. The rate-limiting step for this process – the transfer of Cl− from root symplast to xylem apoplast, which can antagonize delivery of the macronutrient nitrate (NO3−) to shoots – is regulated by abscisic acid (ABA) and is multigenic. Until recently the molecular mechanisms underpinning this salt-tolerance trait were poorly defined. We discuss here how recent advances highlight the role of newly identified transport proteins, some that directly transfer Cl− into the xylem, and others that act on endomembranes in ‘gatekeeper’ cell types in the root stele to control root-to-shoot delivery of Cl−.

  4. Measurement-based modeling of bromine chemistry in the boundary layer: 1. Bromine chemistry at the Dead Sea

    Directory of Open Access Journals (Sweden)

    E. Tas

    2006-01-01

    Full Text Available The Dead Sea is an excellent natural laboratory for the investigation of Reactive Bromine Species (RBS chemistry, due to the high RBS levels observed in this area, combined with anthropogenic air pollutants up to several ppb. The present study investigated the basic chemical mechanism of RBS at the Dead Sea using a numerical one-dimensional chemical model. Simulations were based on data obtained from comprehensive measurements performed at sites along the Dead Sea. The simulations showed that the high BrO levels measured frequently at the Dead Sea could only partially be attributed to the highly concentrated Br− present in the Dead Sea water. Furthermore, the RBS activity at the Dead Sea cannot solely be explained by a pure gas phase mechanism. This paper presents a chemical mechanism which can account for the observed chemical activity at the Dead Sea, with the addition of only two heterogeneous processes: the "Bromine Explosion" mechanism and the heterogeneous decomposition of BrONO2. Ozone frequently dropped below a threshold value of ~1 to 2 ppbv at the Dead Sea evaporation ponds, and in such cases, O3 became a limiting factor for the production of BrOx (BrO+Br. The entrainment of O3 fluxes into the evaporation ponds was found to be essential for the continuation of RBS activity, and to be the main reason for the jagged diurnal pattern of BrO observed in the Dead Sea area, and for the positive correlation observed between BrO and O3 at low O3 concentrations. The present study has shown that the heterogeneous decomposition of BrONO2 has a great potential to affect the RBS activity in areas influenced by anthropogenic emissions, mainly due to the positive correlation between the rate of this process and the levels of NO2. Further investigation of the influence of the decomposition of BrONO2 may be especially important in understanding the RBS activity at mid-latitudes.

  5. Measurement-based modeling of bromine chemistry in the boundary layer: 1. Bromine chemistry at the Dead Sea

    Directory of Open Access Journals (Sweden)

    A. Pour Biazar

    2006-06-01

    Full Text Available The Dead Sea is an excellent natural laboratory for the investigation of Reactive Bromine Species (RBS chemistry, due to the high RBS levels observed in this area, combined with anthropogenic air pollutants up to several ppb. The present study investigated the chemical mechanism of RBS at the Dead Sea using a numerical one-dimensional chemical model. Simulations were based on data obtained from comprehensive measurements performed at sites along the Dead Sea. The simulations showed that the high BrO levels measured frequently at the Dead Sea could only partially be attributed to the highly concentrated Br− present in the Dead Sea water. Further, the RBS activity at the Dead Sea cannot solely be explained by a pure gas phase mechanism. This paper presents a chemical mechanism which can account for the observed chemical activity at the Dead Sea, with the addition of only two heterogeneous processes: the "Bromine Explosion" mechanism and the heterogeneous decomposition of BrONO2. Ozone frequently dropped below a threshold value of ~1 to 2 ppbv at the Dead Sea evaporation ponds, and in such cases, O3 became a limiting factor for the production of BrOx (BrO+Br. The entrainment of O3 fluxes into the evaporation ponds was found to be essential for the continuation of RBS activity, and to be the main reason for the positive correlation observed between BrO and O3 at low O3 concentrations, and for the jagged diurnal pattern of BrO observed in the Dead Sea area. The present study has shown that the heterogeneous decomposition of BrONO2 has the potential to greatly affect the RBS activity in areas under anthropogenic influence, mainly due to the positive correlation between the rate of this process and the levels of NO2. Further investigation of the influence of the decomposition of BrONO2 may be especially important in understanding the RBS activity at mid-latitudes.

  6. High-pressure behavior of bromine confined in the one-dimensional channels of zeolite AlPO4-5 single crystals

    Science.gov (United States)

    Liu, Zhaodong; Yao, Zhen; Yao, Mingguang; Lv, Jiayin; Chen, Shuanglong; Li, Quanjun; Lv, Hang; Wang, Tianyi; Lu, Shuangchen; Liu, Ran; Liu, Bo; Liu, Jing; Chen, Zhiqiang; Zou, Bo; Cui, Tian; Liu, Bingbing

    2016-09-01

    We present a joint experimental and theoretical study on the high-pressure behavior of bromine confined in the one-dimensional (1D) nanochannels of zeolite AlPO4-5 (AFI) single crystals. Raman scattering experiments indicate that loading bromine into AFI single crystals can lead to the formation of bromine molecular chains inside the nanochannels of the crystals. High-pressure Raman and X-ray diffraction studies demonstrate that high pressure can increase the length of the confined bromine molecular chains and modify the inter- and intramolecular interactions of the molecules. The confined bromine shows a considerably different high-pressure behavior to that of bulk bromine. The pressure-elongated bromine molecular chains can be preserved when the pressure is reduced to ambient pressure. Theoretical simulations explain the experimental results obtained from the Raman spectroscopy and X-ray diffraction studies. Furthermore, we find that the intermolecular distance between confined bromine molecules gradually becomes comparable to the intramolecular bond length in bromine molecules upon compression. This may result in the dissociation of the bromine molecules and the formation of 1D bromine atomic chains at pressures above 24 GPa. Our study suggests that the unique nanoconfinement has a considerable effect on the high-pressure behavior of bromine, and the confined bromine species concomitantly enhance the structural stability of the host AFI single crystals.

  7. Brominated flame retardants in end-of-life management not problematic regarding formation of brominated dioxins/furans (PBDD/F)

    Energy Technology Data Exchange (ETDEWEB)

    Drohmann, D. [Great Lakes Chemical, Bergisch Gladbach (Germany); Tange, L. [Eurobrom B.V., Rijswijk (Netherlands); Rothenbacher, K. [Bromine Science and Environmental Forum, Brussels (Belgium)

    2004-09-15

    Bromine is used as the building block for some of the most effective flame retarding agents available to the plastics industry today. They are used to protect against the risk of accidental fires in a wide range of products. Brominated flame retardants (BFRs), as all flame retardants, act to decrease the risk of fire by increasing the fire resistance of the materials in which they are applied. There is a perception that BFRs affect adversely the end-of-life management of plastics through formation of brominated dioxins and furans (PBDD/F). In fact, there exists a wide range of data and practical experience demonstrating that the end-of-life management of plastics containing BFRs are fully compliant with legislation setting the strictest limit values for PBDD/F and is fully compatible with an integrated waste management concept. Furthermore, all existing EU Risk Assessments on BFRs according to the European Existing Substance Regulations include an assessment of the potential formation of dioxins and furans. All assessments conclude that the risks along the life-cycle of the chemicals for human health and the environment associated with the potential formation of PBDD/F are negligible. Moreover, two recent Swedish studies found, that consumer products with BFRs emit less pollutants than the same products without any FRs. This paper summarises available studies and presents the latest results regarding potential formation of brominated dioxins and furans in end-of-life management of plastics containing brominated flame retardants. Additionally, before BFR products enter the market they are tested for PBDD/F according to the ''German Dioxin Ordinance''. Depending on the substitution pattern the limit values for PBDD/F are set at <1{mu}g/kg (ppb) respectively <5{mu}g/kg (ppb).

  8. Utilization of oxidation reactions for the spectrophotometric determination of captopril using brominating agents

    Science.gov (United States)

    El-Didamony, Akram M.; Erfan, Eman A. H.

    2010-03-01

    Three simple, accurate and sensitive methods (A-C) for the spectrophotometric assay of captopril (CPL) in bulk drug, in dosage forms and in the presence of its oxidative degradates have been described. The methods are based on the bromination of captopril with a solution of excess brominating mixture in hydrochloric acid medium. After bromination, the excess brominating mixture is followed by the estimation of surplus bromine by three different reaction schemes. In the first method (A), the determination of the residual bromine is based on its ability to bleach the indigo carmine dye and measuring the absorbance at 610 nm. Method B, involves treating the unreacted bromine with a measured excess of iron(II) and the remaining iron(II) is complexed with 1,10-phenanthroline and the increase in absorbance is measured at 510 nm. In method (C), the surplus bromine is treated with excess of iron(II) and the resulting iron(III) is complexed with thiocyanate and the absorbance is measured at 478 nm. In all the methods, the amount of bromine reacted corresponds to the drug content. The different experimental parameters affecting the development and stability of the color are carefully studied and optimized. Beer's law is valid within a concentration range of 0.4-6.0, 0.4-2.8 and 1.2-4.8 μg mL -1 for methods A, B and C, respectively. The calculated apparent molar absorptivity was found to be 5.16 × 10 4, 9.95 × 10 4 and 1.74 × 10 5 L mol -1 cm -1, for methods A, B and C, respectively. Sandell's sensitivity, correlation coefficients, detection and quantification limits are also reported. No interference was observed from common additives found in pharmaceutical preparations. The proposed methods are successfully applied to the determination of CPL in the tablet formulations with mean recoveries of 99.94-100.11% and the results were statistically compared with those of a reference method by applying Student's t- and F-test.

  9. Terminal elimination half-lives of the brominated flame retardants TBBPA, HBCD, and lower brominated PBDEs in humans

    Energy Technology Data Exchange (ETDEWEB)

    Geyer, H.J.; Schramm, K.W.; Feicht, E.A.; Fried, K.W.; Henkelmann, B.; Lenoir, D. [GSF-National Research Center, Institute of Ecological Chemistry, Neuherberg (Germany); Darnerud, P.O.; Aune, M. [Swedish National Food Administration, Uppsala (Sweden); Schmid, P. [Swiss Federal Laboratories for Materials Testing and Research, Laboratory of Organic Chemistry, EMPA Duebendorf (Switzerland); McDonald, T.A. [Office of Environmental Health Assessment, California EPA, Oakland, CA (United States)

    2004-09-15

    Brominated flame retardants (BFRs) are widely used in polymers and textiles and applied in electronic equipment, construction materials, and furniture for the purpose of fire prevention. BFRs with the highest production volume are tetrabromobisphenol A (TBBPA), 1,2,5,6,9,10- hexabromocyclododecanes (HBCDs: {alpha}-HBCD + {beta}-HBCD + {gamma}-HBCD), and polybrominated diphenyl ethers (PBDEs). Several BFRs are highly lipophilic persistent organic pollutants (POPs) which have been identified in the aquatic and terrestrial environment including wildlife and humans. In exposed organisms including humans toxic effects, bioaccumulation, metabolism, and pharmacokinetics (especially half-life t{sub 1/2}) are important criterions in the hazard assessment. The aim of the present study was to estimate the terminal elimination half-lives (t{sub 1/2H}) of the main BFRs from the whole body (also named body-burden half-life) and/or from the adipose tissue (fat) of adult humans. The t{sub 1/2H} data for the following BFRs were evaluated: TBBPA, HBCD, 2,2',4,4'- tetrabromodiphenyl ether (BDE-47), 2,2',4,4',5-pentaBDE (BDE-99), 2,2',4,4',6-pentaBDE (BDE- 100), 2,2',4,4',5,5'-hexaBDE (BDE-153), and 2,2',4,4',5,6-hexaBDE (BDE-154).

  10. A serial dual-electrode detector based on electrogenerated bromine for capillary electrophoresis.

    Science.gov (United States)

    Du, Fuying; Cao, Shunan; Fung, Ying-Sing

    2014-12-01

    A new serial dual-electrode detector for CE has been designed and fabricated for postcolumn reaction detection based on electrogenerated bromine. A coaxial postcolumn reactor was employed to introduce bromide reagent and facilitate the fabrication of upstream generation electrode by simply sputtering Pt film onto the outer surface of the separation capillary. Bromide introduced could be efficiently converted to bromine at this Pt film electrode and subsequently detected by the downstream Pt microdisk detection electrode. Analytes that react with bromine could be determined by the decrease of bromine reduction current at the downstream electrode resulting from the reaction between analytes and bromine. The effects of serial dual-electrode detector working conditions including electrode potentials, bromide flow rate, and bromide concentration on analytical performance were investigated using glutathione (GSH) and glutathione disulfide (GSSG) as test analytes. Under the optimal conditions, detection limits down to 0.16 μM for GSH and 0.14 μM for GSSG (S/N = 3) as well as linear working ranges of two orders of magnitude for GSH and GSSG were achieved. Furthermore, the separation efficiency obtained by our dual-electrode detector design was greatly improved compared with previous reported design. The developed method has been successfully applied to determine the GSH and GSSG impurity in commercial GSH supplement.

  11. Removal of brominated flame retardant from electrical and electronic waste plastic by solvothermal technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Cong-Cong [Research Center For Eco-Environmental Sciences, Chinese Academy of Sciences, 18 Shuangqing Road, Beijing 100085 (China); Zhang, Fu-Shen, E-mail: fszhang@rcees.ac.cn [Research Center For Eco-Environmental Sciences, Chinese Academy of Sciences, 18 Shuangqing Road, Beijing 100085 (China)

    2012-06-30

    Highlights: Black-Right-Pointing-Pointer A process for brominated flame retardants (BFRs) removal in plastic was established. Black-Right-Pointing-Pointer The plastic became bromine-free with the structure maintained after this treatment. Black-Right-Pointing-Pointer BFRs transferred into alcohol solvent were easily debrominated by metallic copper. - Abstract: Brominated flame retardants (BFRs) in electrical and electronic (E and E) waste plastic are toxic, bioaccumulative and recalcitrant. In the present study, tetrabromobisphenol A (TBBPA) contained in this type of plastic was tentatively subjected to solvothermal treatment so as to obtain bromine-free plastic. Methanol, ethanol and isopropanol were examined as solvents for solvothermal treatment and it was found that methanol was the optimal solvent for TBBPA removal. The optimum temperature, time and liquid to solid ratio for solvothermal treatment to remove TBBPA were 90 Degree-Sign C, 2 h and 15:1, respectively. After the treatment with various alcohol solvents, it was found that TBBPA was finally transferred into the solvents and bromine in the extract was debrominated catalyzed by metallic copper. Bisphenol A and cuprous bromide were the main products after debromination. The morphology and FTIR properties of the plastic were generally unchanged after the solvothermal treatment indicating that the structure of the plastic maintained after the process. This work provides a clean and applicable process for BFRs-containing plastic disposal.

  12. Effect of the Bromine-Based Flame Retardant Plastic Pyrolysis of Hydrotalcite

    Directory of Open Access Journals (Sweden)

    Morita N.

    2016-01-01

    Full Text Available In this study, a method is presented to decrease halogen compounds in the product oil from thermolysis of polystyrene and polypropylene mixed plastic spiked with tetrabromobisphenol A. A mixture of hydrotalcite and plastic was pyrolyzed in a glass reactor at 400 °C under a nitrogen atmosphere. Bromine compounds in the residual substances were measured. The yield of product oil increased using hydrotalcite as an additive. The bromine compounds that were the major ingredients in the oil after thermolysis at 400 °C from the mixed plastic, which also included toluene, ethyl benzene, styrene, and 1-methylethyl benzene, were 2-bromohexane, 3-bromo-1-propenyl benzene, 4,5-dibromodecane, 1-bromomethylbenzene, 3-bromophenol, and 4-bromo-2,6-dimethylbenzaniline. However, bromine compounds were not detected in the product oil, residue, or gas when hydrotalcite was added. After the thermolysis of the plastic, bromine compounds in the product oil may decrease because bromine was captured by the added hydrotalcite.

  13. GAS SORPTION AND TRANSPORT IN POLY (PHENYLENE OXIDE )(PPO)AND ARYL-BROMINATED PPO MEMBRANES

    Institute of Scientific and Technical Information of China (English)

    JIA Lianda; F.R.SHEU, R.T. CHERN; H.B. HOPFENBERG

    1989-01-01

    The apparent solubility (S), concentration- average diffusivity (D), and permeability (P), for CO2,CH4 and N2 through PPO and aryl- brominated PPO at 35 ℃ for pressure ranging from 1 to 26 atm are reported. It is found that P,D, and Sof the membranes to all the three gases vary with the extent of bromination. S increases with the increase of the perecnt of bromine in each case, but D to CO2 increases remarkably only at higher degree of bromination, and therefore, P to CO2 is increased by more than 100% over a wide range of pressure in the case .The solubility data are well described by the dual mode sorption model. It is found that the gas molecules sorbed by the Langmuir mode are relatively more immobilized and the contribution of the nonequilibrium character of the polymer to gas permeation increases obviously for CO2 and is hardly changed for CH4 with increasing bromine content. These observations are interpreted in terms of changes in specific free volume (SFV)and the cohesive energy density (CED) of the polymers.

  14. Characterization of unknown brominated disinfection byproducts during chlorination using ultrahigh resolution mass spectrometry.

    Science.gov (United States)

    Zhang, Haifeng; Zhang, Yahe; Shi, Quan; Zheng, Hongdie; Yang, Min

    2014-03-18

    Brominated disinfection byproducts (Br-DBPs), formed from the reaction of disinfectant(s) with natural organic matter in the presence of bromide in raw water, are generally more cytotoxic and genotoxic than their chlorinated analogues. To date, only a few Br-DBPs in drinking water have been identified, while a significant portion of Br-DBPs in drinking water is still unknown. In this study, negative ion electrospray ionization ultrahigh resolution Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS) was used to characterize unknown Br-DBPs in artificial drinking water. In total, 441 formulas for one-bromine-containing products and 37 formulas for two-bromine-containing products, most of which had not been previously reported, were detected in the chlorinated sample. Most Br-DBPs have corresponding chlorine-containing analogues with identical CHO composition. In addition, on-resonance collision-induced dissociation (CID) of single ultrahigh resolved bromine containing mass peaks was performed in the ICR cell to isolate single bromine-containing components in a very complex natural organic matter spectrum and provide structure information. Relatively abundant neutral loss of CO2 was observed in MS-MS spectra, indicating that the unknown Br-DBPs are rich in carboxyl groups. The results demonstrate that the ESI FT-ICR MS method could provide valuable molecular composition and structure information on unknown Br-DBPs.

  15. Sea ice and pollution-modulated changes in Greenland ice core methanesulfonate and bromine

    Science.gov (United States)

    Maselli, Olivia J.; Chellman, Nathan J.; Grieman, Mackenzie; Layman, Lawrence; McConnell, Joseph R.; Pasteris, Daniel; Rhodes, Rachael H.; Saltzman, Eric; Sigl, Michael

    2017-01-01

    Reconstruction of past changes in Arctic sea ice extent may be critical for understanding its future evolution. Methanesulfonate (MSA) and bromine concentrations preserved in ice cores have both been proposed as indicators of past sea ice conditions. In this study, two ice cores from central and north-eastern Greenland were analysed at sub-annual resolution for MSA (CH3SO3H) and bromine, covering the time period 1750-2010. We examine correlations between ice core MSA and the HadISST1 ICE sea ice dataset and consult back trajectories to infer the likely source regions. A strong correlation between the low-frequency MSA and bromine records during pre-industrial times indicates that both chemical species are likely linked to processes occurring on or near sea ice in the same source regions. The positive correlation between ice core MSA and bromine persists until the mid-20th century, when the acidity of Greenland ice begins to increase markedly due to increased fossil fuel emissions. After that time, MSA levels decrease as a result of declining sea ice extent but bromine levels increase. We consider several possible explanations and ultimately suggest that increased acidity, specifically nitric acid, of snow on sea ice stimulates the release of reactive Br from sea ice, resulting in increased transport and deposition on the Greenland ice sheet.

  16. The NBS Reaction: A Simple Explanation for the Predominance of Allylic Substitution over Olefin Addition by Bromine at Low Concentrations.

    Science.gov (United States)

    Wamser, Carl C.; Scott, Lawrence T.

    1985-01-01

    Examines mechanisms related to use of N-bromosuccinimide (NBS) for bromination at an allylic position. Also presents derived rate laws for three possible reactions of molecular bromine with an alkene: (1) free radical substitution; (2) free radical addition; and (3) electrophilic addition. (JN)

  17. Influence of temperature and heating time on bromination of zinc oxide during thermal treatment with tetrabromobisphenol A.

    Science.gov (United States)

    Grabda, Mariusz; Oleszek-Kudlak, Sylwia; Shibata, Etsuro; Nakamura, Takashi

    2009-12-01

    Our prior research indicates that hydrogen bromide (HBr) evolved during thermal decomposition of tetrabromobisphenol A (TBBPA) can be utilized as a reagent for selective bromination and evaporation of zinc oxide. The present work investigated dependency of the bromination reaction on time at selected temperatures using a laboratory-scale furnace. The formed solid, condensed, and gaseous products were analyzed by X-ray diffraction analysis, electron probe microanalysis, inductively coupled plasma analysis, ion chromatography, and gas chromatography coupled with mass spectrometry. Results indicate that the bromination rate is strongly dependent on heating time. This dependency is a direct consequence of progress in the decomposition of TBBPA, which provides inorganic bromine suitable for the reaction. The bromination rate increases with time until the bromine source is depleted. The process is shorter at higher applied temperatures and appears instantaneous at 310 degrees C and above. However, the maximum bromination yield is independent of the applied conditions and ranges from 64 to 70%. Additionally, the influence of oxidizing conditions on the bromination reaction and the effect of ZnO on decomposition of TBBPA were investigated in this study.

  18. Synthesis of 2-arylbenzimidazoles and 2-arylbenzothiazoles in both room temperature and microwave condition catalyzed by hexamethylenetetramine-bromine complex

    Institute of Scientific and Technical Information of China (English)

    Kaveh Khosravi; Samira Kazemi

    2012-01-01

    One-pot condensation of 2-aminothiophenol or 1,2-phenylenediamine with different aldehydes has been catalyzed by hexamethylenetetramine-bromine (HMTA-Bromine) as new,available and effective catalyst.2-Arylbenzo thiazoles and 2-aryl benzimidazoles have been achieved in excellent yield and good purity.

  19. Nitrated and Brominated Narcotine and its Cleaved Adduct as Butyrylcholinesterase Inhibitors

    Directory of Open Access Journals (Sweden)

    M. A. Abbasi

    2013-09-01

    Full Text Available Narcotine is a very antitussive agent and its modification may lead to some more biological activities. In this presented paper, narcotine (1 was first subjected to nitration and bromination to yield nitrated narcotine (2 and brominated narcotine (3. It was further made to react with phenylchloroformate (6 to give a cleaved addition product 4. This adduct 4 was further nitrated and brominated to yield substituted derivatives 5 and 6, respectively. The structure elucidation of the synthesized compounds was processed via IR, EI-MS and 1H-NMR spectra. These were also screened against butyrylcholinesterase enzyme and were found to the moderate inhibitors of butyrylcholinesterase except nitrated product, 2, of narcotine (1.

  20. The separation of waste printed circuit board by dissolving bromine epoxy resin using organic solvent.

    Science.gov (United States)

    Zhu, P; Chen, Y; Wang, L Y; Zhou, M; Zhou, J

    2013-02-01

    Separation of waste printed circuit boards (WPCBs) has been a bottleneck in WPCBs resource processing. In this study, the separation of WPCBs was performed using dimethyl sulfoxide (DMSO) as a solvent. Various parameters, which included solid to liquid ratio, temperature, WPCB sizes, and time, were studied to understand the separation of WPCBs by dissolving bromine epoxy resin using DMSO. Experimental results showed that the concentration of dissolving the bromine epoxy resin increased with increasing various parameters. The optimum condition of complete separation of WPCBs was solid to liquid ratio of 1:7 and WPCB sizes of 16 mm(2) at 145°C for 60 min. The used DMSO was vapored under the decompression, which obtained the regenerated DMSO and dissolved bromine epoxy resin. This clean and non-polluting technology offers a new way to separate valuable materials from WPCBs and prevent the environmental pollution of waste printed circuit boards effectively.

  1. Improved charge carrier lifetime in planar perovskite solar cells by bromine doping

    Science.gov (United States)

    Kiermasch, David; Rieder, Philipp; Tvingstedt, Kristofer; Baumann, Andreas; Dyakonov, Vladimir

    2016-12-01

    The charge carrier lifetime is an important parameter in solar cells as it defines, together with the mobility, the diffusion length of the charge carriers, thus directly determining the optimal active layer thickness of a device. Herein, we report on charge carrier lifetime values in bromine doped planar methylammonium lead iodide (MAPbI3) solar cells determined by transient photovoltage. The corresponding charge carrier density has been derived from charge carrier extraction. We found increased lifetime values in solar cells incorporating bromine compared to pure MAPbI3 by a factor of ~2.75 at an illumination intensity corresponding to 1 sun. In the bromine containing solar cells we additionally observe an anomalously high value of extracted charge, which we deduce to originate from mobile ions.

  2. Bromination of Marine Dissolved Organic Matter following Full Scale Electrochemical Ballast Water Disinfection.

    Science.gov (United States)

    Gonsior, Michael; Mitchelmore, Carys; Heyes, Andrew; Harir, Mourad; Richardson, Susan D; Petty, William Tyler; Wright, David A; Schmitt-Kopplin, Philippe

    2015-08-01

    An extensively diverse array of brominated disinfection byproducts (DBPs) were generated following electrochemical disinfection of natural coastal/estuarine water, which is one of the main treatment methods currently under consideration for ballast water treatment. Ultra-high-resolution mass spectrometry revealed 462 distinct brominated DBPs at a relative abundance in the mass spectra of more than 1%. A brominated DBP with a relative abundance of almost 22% was identified as 2,2,4-tribromo-5-hydroxy-4-cyclopentene-1,3-dione, which is an analogue to several previously described 2,2,4-trihalo-5-hydroxy-4-cyclopentene-1,3-diones in drinking water. Several other brominated molecular formulas matched those of other known brominated DBPs, such as dibromomethane, which could be generated by decarboxylation of dibromoacetic acid during ionization, dibromophenol, dibromopropanoic acid, dibromobutanoic acid, bromohydroxybenzoic acid, bromophenylacetic acid, bromooxopentenoic acid, and dibromopentenedioic acid. Via comparison to previously described chlorine-containing analogues, bromophenylacetic acid, dibromooxopentenoic acid, and dibromopentenedioic acid were also identified. A novel compound at a 4% relative abundance was identified as tribromoethenesulfonate. This compound has not been previously described as a DBP, and its core structure of tribromoethene has been demonstrated to show toxicological implications. Here we show that electrochemical disinfection, suggested as a candidate for successful ballast water treatment, caused considerable production of some previously characterized DBPs in addition to novel brominated DBPs, although several hundred compounds remain structurally uncharacterized. Our results clearly demonstrate that electrochemical and potentially direct chlorination of ballast water in estuarine and marine systems should be approached with caution and the concentrations, fate, and toxicity of DBP need to be further characterized.

  3. Investigation of Mercury Vapor Treatment by Activated Carbon Made from Coconut Shell and Denatured by Elemental Bromine

    Directory of Open Access Journals (Sweden)

    Tran Hong Con

    2015-07-01

    Full Text Available Coconut shell activated carbon of TraVinhcompany, Vietnam was oxidized by bromine solution at pH 4-6 in normal temperature and pressure. The efficiency of bromine carried on AC surface reached 70.95 to 98.50%. The IR spectrum showed that in surface of the brominated AC appeared C-Br, carbonyl and carboxyl groups. The adsorption capacity of brominated AC reached more than 130 mg/g at 40oC and mercury concentration around 32 mg/m3. The mercury vapor adsorption of the material was almost uninfluenced by experimental temperature. Used brominated AC can be regenerated and recovered mercury metal. The regenerated material has adsorption capacity of 86.92% in comparison with initial material and weight loss was 6.23% at laboratory scale examination.

  4. Studies Update Vinyl Chloride Hazards.

    Science.gov (United States)

    Rawls, Rebecca

    1980-01-01

    Extensive study affirms that vinyl chloride is a potent animal carcinogen. Epidemiological studies show elevated rates of human cancers in association with extended contact with the compound. (Author/RE)

  5. Spectral, electrochemical, and catalytic properties of a homologous series of manganese porphyrins as cytochrome P450 model: the effect of the degree of beta-bromination.

    Science.gov (United States)

    da Silva, Dayse Carvalho; DeFreitas-Silva, Gilson; do Nascimento, Eliane; Rebouças, Júlio Santos; Barbeira, Paulo Jorge Sanches; de Carvalho, Maria Eliza Moreira Dai; Idemori, Ynara Marina

    2008-10-01

    A homologous series of beta-brominated porphyrins derived from meso-tetrakis(4-carbomethoxyphenyl)porphyrinatomanganese(III) chloride, i.e., Mn(III)(Br(x)TCMPP)Cl (x=0,2,4,6, and 8), was prepared and investigated as cytochrome P450 models. Hydroxylations of cyclohexane by iodosylbenzene (PhIO) and iodobenzene diacetate (PhI(OAc)(2)) in the presence or absence of water were carried out as P450 model reactions. The influence of the degree of beta-bromination of the macrocycle on the UV-vis spectra, the Mn(III)/Mn(II) reduction potential, and the catalytic properties of the Mn(III)(Br(x)TCMPP)Cl (x=0,2,4,6, and 8) series were examined. The catalytic efficiency does not correlate with the Mn(III)/Mn(II) reduction potential and shows a bell-shaped behavior, where the best results are achieved with the hexabrominated complex. Better hydroxylation yields were achieved by using PhI(OAc)(2) as oxygen donor, but at expenses of catalyst recovery; addition of water to this system resulted in a increase in the reaction rate. Recycling of the more oxidatively robust complexes Mn(III)(Br(6)TCMPP)Cl and Mn(III)(Br(8)TCMPP)Cl is feasible when using PhIO as oxygen donor. Selectivity and UV-vis data suggested that hydroxylation by both PhIO and PhI(OAc)(2) share closely related active species and mechanism. We also show that the Mn(III)/Mn(II) reduction potentials are inappropriate predictors of P450-type activity of Mn porphyrin-catalyzed oxidations.

  6. A Quaternized Polysulfone Membrane for Zinc-Bromine Redox Flow Battery

    OpenAIRE

    Mingqiang Li; Hang Su; Qinggang Qiu; Guang Zhao; Yu Sun; Wenjun Song

    2014-01-01

    A quaternized polysulfone (QNPSU) composite membrane is fabricated for zinc-bromine redox flow battery. The structure of the membrane is examined by FT-IR spectra and SEM. The conductivity of the membrane is tested by electrochemical analyzer. After a zinc-bromine battery with this composite membrane is operated at different voltage while charging and at different current while discharging to examine the performance of the membrane, it is found that the discharge voltage was 0.9672 V and the ...

  7. Parameters Affecting Hydrogen Chloride Measurements

    Science.gov (United States)

    1993-06-01

    contain sea salt, which is hygroscopic because of the magnesium chloride present, or ammonium bisulfate , which mostly comes from sulfur pollution and is...boosters release hydrogen chloride as a combustion product, and hydrazines or nitric acid can be spilled from liquid fuel motors. Monitoring the...solubility constant, and the second is the acid ionization constant. From experimental work, the product of the two constants is well established (Reference

  8. Chloride channels in stroke

    Institute of Scientific and Technical Information of China (English)

    Ya-ping ZHANG; Hao ZHANG; Dayue Darrel DUAN

    2013-01-01

    Vascular remodeling of cerebral arterioles,including proliferation,migration,and apoptosis of vascular smooth muscle cells (VSMCs),is the major cause of changes in the cross-sectional area and diameter of the arteries and sudden interruption of blood flow or hemorrhage in the brain,ie,stroke.Accumulating evidence strongly supports an important role for chloride (Clˉ) channels in vascular remodeling and stroke.At least three Clˉ channel genes are expressed in VSMCs:1) the TMEM16A (or Ano1),which may encode the calcium-activated Clˉ channels (CACCs); 2) the CLC-3 Clˉ channel and Clˉ/H+ antiporter,which is closely related to the volume-regulated Clˉ channels (VRCCs); and 3) the cystic fibrosis transmembrane conductance regulator (CFTR),which encodes the PKA-and PKC-activated Clˉ channels.Activation of the CACCs by agonist-induced increase in intracellular Ca2+ causes membrane depolarization,vasoconstriction,and inhibition of VSMC proliferation.Activation of VRCCs by cell volume increase or membrane stretch promotes the production of reactive oxygen species,induces proliferation and inhibits apoptosis of VSMCs.Activation of CFTR inhibits oxidative stress and may prevent the development of hypertension.In addition,Clˉ current mediated by gammaaminobutyric acid (GABA) receptor has also been implicated a role in ischemic neuron death.This review focuses on the functional roles of Clˉ channels in the development of stroke and provides a perspective on the future directions for research and the potential to develop Clˉ channels as new targets for the prevention and treatment of stroke.

  9. 21 CFR 184.1138 - Ammonium chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution....

  10. Contribution of very short-lived substances to stratospheric bromine loading: uncertainties and constraints

    Directory of Open Access Journals (Sweden)

    J. Aschmann

    2013-02-01

    Full Text Available Very short-lived substances (VSLS still represent a major factor of uncertainty in the quantification of stratospheric bromine loading. One of the major obstacles for short-lived source gases in contributing to the stratosphere is generally thought to be loss of inorganic bromine (Bry in the tropical tropopause layer (TTL due to dehydration. We use sensitivity calculations with a three-dimensional chemistry transport model comprising a consistent parametrization of convective transport and a comprehensive chemistry scheme to investigate the associated processes. The model considers the two most important bromine VSLS, bromoform (CHBr3 and dibromomethane (CH2Br2. The organic bromine source gases as well as the resulting profile of inorganic bromine in the model are consistent with available observations. In contrast to its organic precursors, Bry is assumed to have a significant sorption capacity regarding sedimenting liquid or frozen particles thus the fraction of intact source gases during their ascent through the TTL is a critical factor. We find that source gas injection is the dominant pathway into the stratosphere, about 50% of CHBr3 and 94% of CH2Br2 is able to overcome the cold point tropopause at approximately 17 km altitude, modulated by the interannual variability of the vertical transport efficiency. In fact, our sensitivity calculations indicate that the extent of source gas injection of CHBr3 is highly sensitive to the strength of convection and large-scale ascent; in contrast, modifying the photolysis or the destruction via OH yields a significantly smaller response. In principle, the same applies as well to CH2Br2, though it is considerably less responsive due to its longer lifetime. The next important aspect we identified is that the partitioning of available Bry from short-lived sources is clearly

  11. Contribution of very short-lived substances to stratospheric bromine loading: uncertainties and constraints

    Directory of Open Access Journals (Sweden)

    J. Aschmann

    2012-11-01

    Full Text Available Very short-lived substances (VSLS still represent a major factor of uncertainty in the quantification of stratospheric bromine loading. One of the major obstacles for short-lived source gases in contributing to the stratosphere is generally thought to be loss of inorganic bromine (Bry in the tropical tropopause layer (TTL due to dehydration. We use sensitivity calculations with a~three-dimensional chemistry transport model comprising a consistent parametrization of convective transport and a comprehensive chemistry scheme to investigate the associated processes. The model considers the two most important bromine VSLS, bromoform (CHBr3 and dibromomethane (CH2Br2. The organic bromine source gases as well as the resulting profile of inorganic bromine in the model are consistent with available observations. In contrast to its organic precursors, Bry is assumed to have a~significant sorption capacity regarding sedimenting liquid or frozen particles thus the fraction of intact source gases during their ascent through the TTL is a critical factor. We find that source gas injection is the dominant pathway into the stratosphere, about 50% of CHBr3 and 93% of CH2Br2 is able to overcome the cold point tropopause at approximately 17 km altitude, modulated by the interannual variability of the vertical transport efficiency. In fact, our sensitivity calculations indicate that the extent of source gas injection of CHBr3 is highly sensitive to the strength of convection and large-scale ascent; in contrast, modifying the photolysis or the destruction via OH yields a significantly smaller response. In principal, the same applies as well to CH2Br2, though it is considerably less responsive due to its longer lifetime. The next important aspect we identified is that the partitioning of available Bry from short-lived sources is clearly

  12. 46 CFR 151.50-34 - Vinyl chloride (vinyl chloride monomer).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride (vinyl chloride monomer). 151.50-34... chloride (vinyl chloride monomer). (a) Copper, aluminum, magnesium, mercury, silver, and their alloys shall... equipment that may come in contact with vinyl chloride liquid or vapor. (b) Valves, flanges, and...

  13. 40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... AIR POLLUTANTS National Emission Standard for Vinyl Chloride § 61.65 Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene...

  14. Fate of PBDEs during food processing: Assessment of formation of mixed chlorinated/brominated diphenyl ethers and brominated dioxins/furans.

    Science.gov (United States)

    Roszko, Marek; Szymczyk, Krystyna; Jędrzejczak, Renata

    2015-01-01

    The aim of this study was to evaluate effects of food processing on PBDE levels, in particular influence of heat treatment on degradation of PBDEs, including possible formation of chlorinated diphenyl ethers or brominated dioxins/furans as degradation products. It was shown that PBDEs heated in the presence of chlorine (from either organic or inorganic sources) formed mixed chlorinated/brominated diphenyl ethers. However, no PCDEs were formed in the presence of lipids. Lipid medium increased stability of PBDEs exposed to UV irradiation. Profile of congeners formed in result of the debromination reaction was significantly different than profiles observed by some other authors in aliphatic organic solvents. Grilling processes increased concentrations (calculated on the fresh product basis) of the studied compounds by 4-8/22-34% for electric/coal grill, respectively. Depending on the congener and on the applied heat treatment, PBDE mass in pork meat after grilling dropped by 26-53%. No detectable quantities of either brominated dioxins or furans were formed during thermal processing of food containing typical levels of PBDEs.

  15. Regioselective chlorination and bromination of unprotected anilines under mild conditions using copper halides in ionic liquids

    Directory of Open Access Journals (Sweden)

    Han Wang

    2012-05-01

    Full Text Available By using ionic liquids as solvents, the chlorination or bromination of unprotected anilines at the para-position can be achieved in high yields with copper halides under mild conditions, without the need for potentially hazardous operations such as supplementing oxygen or gaseous HCl.

  16. 二溴海因溴化邻苯二酚%Bromination of Catechol Using Dibromohydantoin

    Institute of Scientific and Technical Information of China (English)

    王宁宁; 鲍猛; 牟宗刚; 王慧; 刘传仁

    2011-01-01

    4, 5 -Dibromocateehol were synthesised by using dibromohydantoin as brominating agent to react with the eatechol, in glacial acetic acid environment, in ice - water bath. The method overcame the shortcomings of the traditional method using liquid bromine as the brominating agent and effectively improved the yield. By studing the molar ratio of brominated agent and raw materials, the reaction time and the reaction temperature, the experiment determined that the optimal molar ratio was 2:1, each appropriate feeding time interval was 20 minutes, and the optimum reaction temperature was -5 -0 ℃.%在冰醋酸环境下,在冰水浴中,用二溴海因作为溴化剂,与邻苯二酚反应合成4,5-二溴邻苯二酚。该方法克服传统方法中用液溴作为溴化剂的缺点并有效地提高了产率。该实验通过对溴化剂与原料的物质的量比、反应时间以及反应温度的研究,确定最佳物质的量比是2:1,每次加料时间间隔为20min为宜、反应最佳温度为-5-O℃。

  17. In vitro profiling of the endocrine-disrupting potency of brominated flame retardants

    NARCIS (Netherlands)

    Hamers, T.H.M.; Kamstra, J.H.; Sonneveld, E.; Murk, A.J.; Kester, M.H.A.; Andersson, P.L.; Legler, J.; Brouwer, A.

    2006-01-01

    Over the last years, increasing evidence has become available that some brominated flame retardants (BFRs) may have endocrine disrupting (ED) potencies. The goal of the current study was to perform a systematic in vitro screening of the ED potencies of BFRs (1) to elucidate possible modes of action

  18. Molecular characterization of brominated persistent pollutants using extended X-ray absorption fine structure (EXAFS) spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Bergknut, Magnus; Skyllberg, Ulf [Swedish University of Agricultural Sciences (SLU), Department of Forest Ecology and Management, Umeaa (Sweden); Persson, Per [Umeaa University, Department of Chemistry, Umeaa (Sweden)

    2008-02-15

    X-ray absorption fine structure (EXAFS) spectroscopy spectra were collected for three brominated persistent pollutants: 6-bromo-2,4,5-trichlorophenol (BrTriClP), pentabromophenol (PentaBrP) and 3,3',5,5'-tetrabromobisphenol A (TBBA). The substances were selected to be symmetrical (BrTriClP and TBBA) or asymmetrical (PentaBrP) with respect to the atomic Br positions and to differ in the number of bromine and other halide atoms, as well as their relative positions. The asymmetrical PentaBrP was modelled with special detail as not all bromine atoms have identical coordination environments. The studied substances displayed unique EXAFS spectra, which could be used to determine the molecular structure in fair detail. We conclude that EXAFS spectroscopy is a suitable technique for molecular characterization of the comparatively complex molecules within the class of compounds of brominated organic persistent pollutants. A detailed understanding of the EXAFS spectra of the pure compounds opens up possibilities to study the interactions with soil and sediment matrices by means of EXAFS spectroscopy. (orig.)

  19. Kinetics of aerobic cometabolic biodegradation of chlorinated and brominated aliphatic hydrocarbons: A review.

    Science.gov (United States)

    Jesus, João; Frascari, Dario; Pozdniakova, Tatiana; Danko, Anthony S

    2016-05-15

    This review analyses kinetic studies of aerobic cometabolism (AC) of halogenated aliphatic hydrocarbons (HAHs) from 2001-2015 in order to (i) compare the different kinetic models proposed, (ii) analyse the estimated model parameters with a focus on novel HAHs and the identification of general trends, and (iii) identify further research needs. The results of this analysis show that aerobic cometabolism can degrade a wide range of HAHs, including HAHs that were not previously tested such as chlorinated propanes, highly chlorinated ethanes and brominated methanes and ethanes. The degree of chlorine mineralization was very high for the chlorinated HAHs. Bromine mineralization was not determined for studies with brominated aliphatics. The examined research period led to the identification of novel growth substrates of potentially high interest. Decreasing performance of aerobic cometabolism were found with increasing chlorination, indicating the high potential of aerobic cometabolism in the presence of medium- and low-halogenated HAHs. Further research is needed for the AC of brominated aliphatic hydrocarbons, the potential for biofilm aerobic cometabolism processes, HAH-HAH mutual inhibition and the identification of the enzymes responsible for each aerobic cometabolism process. Lastly, some indications for a possible standardization of future kinetic studies of HAH aerobic cometabolism are provided.

  20. Deposition history of brominated flame retardant compounds in an ice core from Holtedahlfonna, Svalbard, Norway

    NARCIS (Netherlands)

    Hermanson, M.H.; Isaksson, E.; Forsström, S.; Teixeira, C.; Muir, D.C.G.; Pohjola, V.A.; van de Wal, R.S.W.

    2010-01-01

    Brominated flame retardants (BFRs) have been found in Arctic wildlife, lake sediment, and air. To identify the atmospheric BFR deposition history on Svalbard, Norway, we analyzed 19 BFRs, including hexabromocyclododecane (HBCD), 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE), decabromodiphenyl ethane

  1. Canadian Arctic sea ice reconstructed from bromine in the Greenland NEEM ice core

    Science.gov (United States)

    Spolaor, Andrea; Vallelonga, Paul; Turetta, Clara; Maffezzoli, Niccolò; Cozzi, Giulio; Gabrieli, Jacopo; Barbante, Carlo; Goto-Azuma, Kumiko; Saiz-Lopez, Alfonso; Cuevas, Carlos A.; Dahl-Jensen, Dorthe

    2016-09-01

    Reconstructing the past variability of Arctic sea ice provides an essential context for recent multi-year sea ice decline, although few quantitative reconstructions cover the Holocene period prior to the earliest historical records 1,200 years ago. Photochemical recycling of bromine is observed over first-year, or seasonal, sea ice in so-called “bromine explosions” and we employ a 1-D chemistry transport model to quantify processes of bromine enrichment over first-year sea ice and depositional transport over multi-year sea ice and land ice. We report bromine enrichment in the Northwest Greenland Eemian NEEM ice core since the end of the Eemian interglacial 120,000 years ago, finding the maximum extension of first-year sea ice occurred approximately 9,000 years ago during the Holocene climate optimum, when Greenland temperatures were 2 to 3 °C above present values. First-year sea ice extent was lowest during the glacial stadials suggesting complete coverage of the Arctic Ocean by multi-year sea ice. These findings demonstrate a clear relationship between temperature and first-year sea ice extent in the Arctic and suggest multi-year sea ice will continue to decline as polar amplification drives Arctic temperatures beyond the 2 °C global average warming target of the recent COP21 Paris climate agreement.

  2. Canadian Arctic sea ice reconstructed from bromine in the Greenland NEEM ice core.

    Science.gov (United States)

    Spolaor, Andrea; Vallelonga, Paul; Turetta, Clara; Maffezzoli, Niccolò; Cozzi, Giulio; Gabrieli, Jacopo; Barbante, Carlo; Goto-Azuma, Kumiko; Saiz-Lopez, Alfonso; Cuevas, Carlos A; Dahl-Jensen, Dorthe

    2016-09-21

    Reconstructing the past variability of Arctic sea ice provides an essential context for recent multi-year sea ice decline, although few quantitative reconstructions cover the Holocene period prior to the earliest historical records 1,200 years ago. Photochemical recycling of bromine is observed over first-year, or seasonal, sea ice in so-called "bromine explosions" and we employ a 1-D chemistry transport model to quantify processes of bromine enrichment over first-year sea ice and depositional transport over multi-year sea ice and land ice. We report bromine enrichment in the Northwest Greenland Eemian NEEM ice core since the end of the Eemian interglacial 120,000 years ago, finding the maximum extension of first-year sea ice occurred approximately 9,000 years ago during the Holocene climate optimum, when Greenland temperatures were 2 to 3 °C above present values. First-year sea ice extent was lowest during the glacial stadials suggesting complete coverage of the Arctic Ocean by multi-year sea ice. These findings demonstrate a clear relationship between temperature and first-year sea ice extent in the Arctic and suggest multi-year sea ice will continue to decline as polar amplification drives Arctic temperatures beyond the 2 °C global average warming target of the recent COP21 Paris climate agreement.

  3. Unintentional production of persistent chlorinated and brominated organic pollutants during iron ore sintering processes.

    Science.gov (United States)

    Li, Sumei; Liu, Guorui; Zheng, Minghui; Liu, Wenbin; Li, Jinhui; Wang, Mei; Li, Changliang; Chen, Yuan

    2017-06-05

    Iron ore sintering (SNT) processes are major sources of unintentionally produced chlorinated persistent organic pollutants (POPs), including polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs), and polychlorinated naphthalenes (PCNs). However, few studies of emissions of brominated POPs, such as polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs) and polybrominated diphenyl ethers (PBDEs), during SNT have been performed. Stack gas and fly ash samples from six typical SNT plants in China were collected and analyzed to determine the concentrations and profiles of PCDD/Fs, PCBs, PCNs, PBDD/Fs, and PBDEs, as well as any correlations among these compounds. The PCDD/F, PCB, PCN, PBDD/F, and PBDE emission factors were 2.47, 0.61, 552, 0.32, and 107μgt(-1), respectively (109, 4.07, 10.4, 4.41 and 0.02ng toxic equivalents t(-1), respectively). PCBs were the most abundant compounds by mass, while PCNs were the next most abundant, contributing 51% and 42% to the total POP concentration, respectively. However, PCDD/Fs were the dominant contributors to the chlorinated and brominated POP toxic equivalent concentrations, contributing 89% to the total toxic equivalent concentration. The PCDD/F and other chlorinated and brominated POP concentrations were positively correlated, indicating that chlorinated and brominated POP emissions could be synergistically decreased using the best available technologies/best environmental practices already developed for PCDD/Fs.

  4. Performance and Degradation of A Lithium-Bromine Rechargeable Fuel Cell Using Highly Concentrated Catholytes

    CERN Document Server

    Bai, Peng

    2016-01-01

    Lithium-air batteries have been considered as ultimate solutions for the power source of long-range electrified transportation, but state-of-the-art prototypes still suffer from short cycle life, low efficiency and poor power output. Here, a lithium-bromine rechargeable fuel cell using highly concentrated bromine catholytes is demonstrated with comparable specific energy, improved power density, and higher efficiency. The cell is similar in structure to a hybrid-electrolyte Li-air battery, where a lithium metal anode in nonaqueous electrolyte is separated from aqueous bromine catholytes by a lithium-ion conducting ceramic plate. The cell with a flat graphite electrode can discharge at a peak power density around 9mW cm-2 and in principle could provide a specific energy of 791.8 Wh kg-1, superior to most existing cathode materials and catholytes. It can also run in regenerative mode to recover the lithium metal anode and free bromine with 80-90% voltage efficiency, without any catalysts. Degradation of the sol...

  5. Using the parallelogram approach to estimate human percutaneous bioavailability for novel & legacy brominated flame retardants

    Science.gov (United States)

    (This is an extended abstract. The following text was taken from the Discussion and Conclusion section.) Humans are frequently exposed to brominated flame retardants (BFRs), especially via dermal contact with contaminated dust. Human and rat skin data were integrated using a pa...

  6. On the bromination of the dihydroazulene/vinylheptafulvene photo-/thermoswitch

    DEFF Research Database (Denmark)

    Mazzanti, Virginia; Cacciarini, M.; Broman, Søren Lindbæk;

    2012-01-01

    as of the known 7-bromo-DHA. Results: Radical bromination on two different VHFs by using N-bromosuccinimide/benzoyl peroxide and light, followed by a ring-closure reaction generated the corresponding 3-bromo-DHAs, as confirmed in one case by X-ray crystallography. According to a H-1 NMR spectroscopic study...

  7. Canadian Arctic sea ice reconstructed from bromine in the Greenland NEEM ice core

    Science.gov (United States)

    Spolaor, Andrea; Vallelonga, Paul; Turetta, Clara; Maffezzoli, Niccolò; Cozzi, Giulio; Gabrieli, Jacopo; Barbante, Carlo; Goto-Azuma, Kumiko; Saiz-Lopez, Alfonso; Cuevas, Carlos A.; Dahl-Jensen, Dorthe

    2016-01-01

    Reconstructing the past variability of Arctic sea ice provides an essential context for recent multi-year sea ice decline, although few quantitative reconstructions cover the Holocene period prior to the earliest historical records 1,200 years ago. Photochemical recycling of bromine is observed over first-year, or seasonal, sea ice in so-called “bromine explosions” and we employ a 1-D chemistry transport model to quantify processes of bromine enrichment over first-year sea ice and depositional transport over multi-year sea ice and land ice. We report bromine enrichment in the Northwest Greenland Eemian NEEM ice core since the end of the Eemian interglacial 120,000 years ago, finding the maximum extension of first-year sea ice occurred approximately 9,000 years ago during the Holocene climate optimum, when Greenland temperatures were 2 to 3 °C above present values. First-year sea ice extent was lowest during the glacial stadials suggesting complete coverage of the Arctic Ocean by multi-year sea ice. These findings demonstrate a clear relationship between temperature and first-year sea ice extent in the Arctic and suggest multi-year sea ice will continue to decline as polar amplification drives Arctic temperatures beyond the 2 °C global average warming target of the recent COP21 Paris climate agreement. PMID:27650478

  8. Exposure assessment of Dutch nursing infants to brominated flame retardants via breast milk

    NARCIS (Netherlands)

    Winter-Sorkina R de; Bakker MI; Baumann RA; Hoogerbrugge R; Zeilmaker MJ; SIR

    2004-01-01

    As part of a national survey on the occurrence of persistent organic contaminants in breast milk, a group of brominated flame retardants (polybrominated diphenyl ethers or PBDEs) was measured in breast milk which had been collected in 1998 from Dutch primiparous women on day 6 to 10 after labour. To

  9. Toxicity of brominated flame retardants in fish, with emphasis on endocrine effects and reproduction

    NARCIS (Netherlands)

    Kuiper, R.V.

    2007-01-01

    Abstract The abundant use of brominated flame retardants (BFRs) in modern polymers has over the passed decades resulted in contamination of the environment, and BFRs are increasingly found in fish. Laboratory studies have shown that a number of BFRs and BFR-metabolites can interfere with thyroid and

  10. Brominated Flame Retardants and their metabolites: Novel insights into endocrine disruptive properties.

    NARCIS (Netherlands)

    Fernández Cantón, R.

    2008-01-01

    Brominated flame retardants (BFRs) are chemicals that are added to materials to inhibit or suppress ignition and are incorporated during the manufacture of e.g. electronic equipment, furniture, construction materials and textiles. BFRs have become an increasingly important group of organohalogen com

  11. Brominated flame retardants and the formation of dioxins and furans in fires and combustion.

    Science.gov (United States)

    Zhang, Mengmei; Buekens, Alfons; Li, Xiaodong

    2016-03-05

    The widespread use and increasing inventory of brominated flame retardants (BFRs) have caused considerable concern, as a result of BFRs emissions to the environment and of the formation of both polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs) and mixed polybromochloro-dibenzo-p-dioxins and dibenzofurans (PBCDD/Fs or PXDD/Fs). Structural similarities between PBDD/Fs and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) suggest the existence of comparable formation pathways of both PBDD/Fs and PCDD/Fs, yet BFRs also act as specific precursors to form additional PBDD/Fs. Moreover, elementary bromine (Br2) seems to facilitate chlorination by bromination of organics, followed by Br/Cl-exchange based on displacement through the more reactive halogen. Overall, PBDD/Fs form through three possible pathways: precursor formation, de novo formation, and dispersion of parts containing BFRs as impurities and surviving a fire or other events. The present review summarises the formation mechanisms of both brominated (PBDD/Fs) and mixed dioxins (PXDD/Fs with X=Br or Cl) from BFRs, recaps available emissions data of PBDD/Fs and mixed PXDD/Fs from controlled waste incineration, uncontrolled combustion sources and accidental fires, and identifies and analyses the effects of several local factors of influence, affecting the formation of PBDD/Fs and mixed PXDD/Fs during BFRs combustion.

  12. Thermoelectric properties of bromine filled CoSb3 skutterudite

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, Brenden R.; Crawford, Caitlin M.; McKinney, Robert W.; Parilla, Philip A.; Toberer, Eric S.

    2016-01-01

    Historically, the improved thermoelectric performance of skutterudite compounds has largely been driven by the incorporation of electropositive donors on interstitial sites. These 'rattlers' serve to optimize both electronic and thermal properties by tuning the carrier concentration and scattering phonons. In this work, we show that interstitial bromine can be incorporated into CoSb3 and assess the impact on electronic and thermal transport. In contrast to prior high pressure syntheses with iodine, interstitial bromine incorporation is achieved at ambient pressure. Transport properties are stable up to at least 375 degrees C. Bromine serves as an electronegative acceptor and can induce degenerate (>5 x 1019 cm-3) hole densities. In contrast to other p-type skutterudite compositions, bromine preserves the intrinsically high hole mobility of CoSb3 while significantly reducing the lattice thermal conductivity. The development of a stable p-type dopant for the interstitial filler site enables the development of skutterudites with both donor and acceptor interstitials to maximize phonon scattering while maintaining the high mobility of CoSb3.

  13. The Effects of Bromination Methods on the Microstructure of Brominated Natural Rubbers from Latex%溴化方式对胶乳法溴化天然橡胶结构的影响

    Institute of Scientific and Technical Information of China (English)

    赵法敏; 薛行华; 张子琦; 张利伟; 李光

    2013-01-01

    为改善溴化天然橡胶(BNR)的溶解性能,在胶乳法的基础上改变溴化方式,以常规溴化方式和分步溴化方式分别制备了BNR.通过实验发现,体系溴浓度相同时分步溴化方式的溴含量比常规溴化方式高,而凝胶含量较低,所以分步溴化方式在甲苯中的溶解性能较好.通过傅里叶红外光谱对样品进行表征,并使用核磁共振对其微观结构进行了定性定量分析.红外光谱分析表明,2种溴化方式制备的BNR产物均发生了一定程度的溴加成反应和溴取代反应;核磁共振的分析证实了在体系溴浓度较低的情况下,与胶乳法常规溴化相反,胶乳法分步溴化的溴化过程主要以溴加成反应为主,少量发生溴取代反应.%In order to improve the solubility property of the brominated natural rubbers (BNR)from latex, BNR were prepared by changing the bromination ways from conventional bromination to step bromination. Through the experiment, it was discovered that the bromine content of the latter was higher than the former, but the gel content was less under the same bromine concentration. The latter showed much better solubility in the solvent of toluene. The structure of the procured sample was characterized by Fourier transform infrared spectroscopy (FTIR), and the microstructures of brominated nature rubber were qualitatively and quantitatively analyzed by nuclear magnetic resonance (NMR). FTIR showed that there were both a degree of brominated addition reaction and brominated substitution reaction in the obtained BNR by two different methods; Contrary to the conventional bromination from latex, the analysis of NMR proved that the bromination process of step bromination from latex was mainly in the form of addition reaction, and only a small amount of the substitution reaction did occur.

  14. Electrochemical Chloride extraction using external electrodes?

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul

    2006-01-01

    Electrochemical methods for the removal of chloride from concrete have been developed and the methods are primarily designed for situations where corrosion has started due to an increased chloride concentration in the vicinity of the reinforcement. In these methods the reinforcement is used...... as the cathode. However, some unwanted side effects can occur, including alkali-silica reaction and in some cases hydrogen embrittlement. It is also suggested also to use electrochemical chloride extraction in a preventive way in constructions where chloride induced corrosion is likely to be a problem after...... a period of time, i.e. remove the chlorides before the chloride front reaches the reinforcement. If the chlorides are removed from outer few centimetres from the surface, the chloride will not reach the reinforcement and cause damage. By using the electrochemical chloride removal in this preventive way...

  15. Distribution of copper, silver and gold during thermal treatment with brominated flame retardants

    Energy Technology Data Exchange (ETDEWEB)

    Oleszek, Sylwia, E-mail: sylwia_oleszek@yahoo.com [Institute of Multidisciplinary Research for Advanced Materials (IMRAM), Tohoku University, 1,1 Katahira, 2-Chome, Sendai 980-8577 (Japan); Institute of Environmental Engineering of the Polish Academy of Sciences, 34 M. Sklodowska-Curie St., 41-819 Zabrze (Poland); Grabda, Mariusz, E-mail: mariusz@mail.tagen.tohoku.ac.jp [Institute of Multidisciplinary Research for Advanced Materials (IMRAM), Tohoku University, 1,1 Katahira, 2-Chome, Sendai 980-8577 (Japan); Institute of Environmental Engineering of the Polish Academy of Sciences, 34 M. Sklodowska-Curie St., 41-819 Zabrze (Poland); Shibata, Etsuro, E-mail: etsuro@tagen.tohoku.ac.jp [Institute of Multidisciplinary Research for Advanced Materials (IMRAM), Tohoku University, 1,1 Katahira, 2-Chome, Sendai 980-8577 (Japan); Nakamura, Takashi, E-mail: ntakashi@tagen.tohoku.ac.jp [Institute of Multidisciplinary Research for Advanced Materials (IMRAM), Tohoku University, 1,1 Katahira, 2-Chome, Sendai 980-8577 (Japan)

    2013-09-15

    Highlights: • Copper, silver and gold during thermal treatment with brominated flame retardants. • Distribution of copper, silver and gold during thermal processing. • Thermodynamic considerations of the bromination reactions. - Abstract: The growing consumption of electric and electronic equipment results in creating an increasing amount of electronic waste. The most economically and environmentally advantageous methods for the treatment and recycling of waste electric and electronic equipment (WEEE) are the thermal techniques such as direct combustion, co-combustion with plastic wastes, pyrolysis and gasification. Nowadays, this kind of waste is mainly thermally treated in incinerators (e.g. rotary kilns) to decompose the plastics present, and to concentrate metals in bottom ash. The concentrated metals (e.g. copper, precious metals) can be supplied as a secondary raw material to metal smelters, while the pyrolysis of plastics allows the recovery of fuel gases, volatilising agents and, eventually, energy. Indeed, WEEE, such as a printed circuit boards (PCBs) usually contains brominated flame retardants (BFRs). From these materials, hydrobromic acid (HBr) is formed as a product of their thermal decomposition. In the present work, the bromination was studied of copper, silver and gold by HBr, originating from BFRs, such as Tetrabromobisphenol A (TBBPA) and Tetrabromobisphenol A-Tetrabromobisophenol A diglycidyl ether (TTDE) polymer; possible volatilization of the bromides formed was monitored using a thermo-gravimetric analyzer (TGA) and a laboratory-scale furnace for treating samples of metals and BFRs under an inert atmosphere and at a wide range of temperatures. The results obtained indicate that up to about 50% of copper and silver can evolve from sample residues in the form of volatile CuBr and AgBr above 600 and 1000 °C, respectively. The reactions occur in the molten resin phase simultaneously with the decomposition of the brominated resin. Gold is

  16. Interactions of bromine, chlorine, and iodine photochemistry during ozone depletions in Barrow, Alaska

    Directory of Open Access Journals (Sweden)

    C. R. Thompson

    2014-11-01

    Full Text Available The springtime depletion of tropospheric ozone in the Arctic is known to be caused by active halogen photochemistry resulting from halogen atom precursors emitted from snow, ice, or aerosol surfaces. The role of bromine in driving ozone depletion events (ODEs has been generally accepted, but much less is known about the role of chlorine radicals in ozone depletion chemistry. While the potential impact of iodine in the High Arctic is more uncertain, there have been indications of active iodine chemistry through observed enhancements in filterable iodide, probable detection of tropospheric IO, and recently, detection of atmospheric I2. Despite decades of research, significant uncertainty remains regarding the chemical mechanisms associated with the bromine-catalyzed depletion of ozone, as well as the complex interactions that occur in the polar boundary layer due to halogen chemistry. To investigate this, we developed a zero-dimensional photochemical model, constrained with measurements from the 2009 OASIS field campaign in Barrow, Alaska. We simulated a 7 day period during late March that included a full ozone depletion event lasting 3 days and subsequent ozone recovery to study the interactions of halogen radicals under these different conditions. In addition, the effects of iodine added to our base model were investigated. While bromine atoms were primarily responsible for ODEs, chlorine and iodine were found to enhance the depletion rates and iodine was found to be more efficient per atom at depleting ozone than Br. The interaction between chlorine and bromine is complex, as the presence of chlorine can increase the recycling and production of Br atoms, while also increasing reactive bromine sinks under certain conditions. Chlorine chemistry was also found to have significant impacts on both HO2 and RO2. The results of this work highlight the need for future studies on the production mechanisms of Br2 and Cl2, as well as on the potential

  17. Monitoring of WEEE plastics in regards to brominated flame retardants using handheld XRF

    Energy Technology Data Exchange (ETDEWEB)

    Aldrian, Alexia, E-mail: alexia.aldrian@unileoben.ac.at [Chair of Waste Processing Technology and Waste Management, Montanuniversitaet Leoben, Franz-Josef-Straße 18, 8700 Leoben (Austria); Ledersteger, Alfred, E-mail: a.ledersteger@saubermacher.at [Saubermacher Dienstleistungs AG, Hans-Roth-Straße 1, 8073 Feldkirchen bei Graz (Austria); Pomberger, Roland, E-mail: roland.pomberger@unileoben.ac.at [Chair of Waste Processing Technology and Waste Management, Montanuniversitaet Leoben, Franz-Josef-Straße 18, 8700 Leoben (Austria)

    2015-02-15

    Highlights: • Specification of an empirical factor for conversion from bromine to PBB and PBDE. • The handheld XRF device was validated for this particular application. • A very large number of over 4600 pieces of monitor housings was analysed. • The recyclable fraction mounts up to 85% for TV but only 53% of PC waste plastics. • A high percentage of pieces with bromine contents of over 50,000 ppm was obtained. - Abstract: This contribution is focused on the on-site determination of the bromine content in waste electrical and electronic equipment (WEEE), in particular waste plastics from television sets (TV) and personal computer monitors (PC) using a handheld X-ray fluorescence (XRF) device. The described approach allows the examination of samples in regards to the compliance with legal specifications for polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) directly after disassembling and facilitates the sorting out of plastics with high contents of brominated flame retardants (BFRs). In all, over 3000 pieces of black (TV) and 1600 pieces of grey (PC) plastic waste were analysed with handheld XRF technique for this study. Especially noticeable was the high percentage of pieces with a bromine content of over 50,000 ppm for TV (7%) and PC (39%) waste plastics. The applied method was validated by comparing the data of handheld XRF with results obtained by GC–MS. The results showed the expected and sufficiently accurate correlation between these two methods. It is shown that handheld XRF technique is an effective tool for fast monitoring of large volumes of WEEE plastics in regards to BFRs for on-site measurements.

  18. Determination of iodine and bromine compounds in foodstuffs by CE-inductively coupled plasma MS.

    Science.gov (United States)

    Chen, Jing-Huan; Wang, Kai-en; Jiang, Shiuh-Jen

    2007-11-01

    A CE-inductively coupled plasma mass spectrometric (CE-ICP-MS) method for iodine and bromine speciation analysis is described. Samples containing ionic iodine (I(-) and IO(3)(-)) and bromine (Br(-) and BrO(3)(-)) species are subjected to electrophoretic separation before injection into the microconcentric nebulizer (CEI-100). The separation has been achieved in a 50 cm length x 75 microm id fused-silica capillary. The electrophoretic buffer used is 10 mmol/L Tris (pH 8.0), while the applied voltage is set at -8 kV. Detection limits are 1 and 20-50 ng/mL for various I and Br compounds, respectively, based on peak height. The RSD of the peak areas for seven injections of 0.1 microg/mL I(-), IO(3)(-) and 1 microg/mL Br(-), BrO(3)(-) mixture is in the range of 3-5%. This method has been applied to determine various iodine and bromine species in NIST SRM 1573a Tomato Leaves reference material and a salt and seaweed samples obtained locally. A microwave-assisted extraction method is used for the extraction of these compounds. Over 87% of the total iodine and 83% of the total bromine are extracted using a 10% m/v tetramethylammonium hydroxide (TMAH) solution in a focused microwave field within a period of 10 min. The spike recoveries are in the range of 94-105% for all the determinations. The major species of iodine and bromine in tomato leaves, salt, and seaweed are Br(-), IO(3)(-), I(-), and Br(-), respectively.

  19. Iodine and bromine speciation in snow and the effect of orographically induced precipitation

    Directory of Open Access Journals (Sweden)

    H. Biester

    2007-05-01

    Full Text Available Iodine is an essential trace element for all mammals and may also influence climate through new aerosol formation. Atmospheric bromine cycling is also important due to its well-known ozone depletion capabilities. Despite precipitation being the ultimate source of iodine in the terrestrial environment, the processes effecting its distribution, speciation and transport are relatively unknown. The aim of this study was to determine the effect of orographically induced precipitation on iodine concentrations in snow and also to quantify the inorganic and organic iodine and bromine species. Snow samples were collected over an altitude profile (~840 m from the northern Black Forest and were analysed by ion-chromatography - inductively coupled plasma mass spectrometry (IC-ICP-MS for iodine and bromine species and trace metals (ICP-MS. All elements and species concentrations in snow showed significant (r2>0.65 exponential decrease relationships with altitude despite the short (5 km horizontal distance of the transect. In fact, total iodine more than halved (38 to 13 nmol/l over the 840 m height change. The results suggest that orographic lifting and subsequent precipitation has a major influence on iodine concentrations in snow. This orographically induced removal effect may be more important than lateral distance from the ocean in determining iodine concentrations in terrestrial precipitation. The microphysical removal process was common to all elements indicating that the iodine and bromine are internally mixed within the snow crystals. We also show that organically bound iodine is the dominant iodine species in snow (61–75%, followed by iodide. Iodate was only found in two samples despite a detection limit of 0.3 nmol/l. Two unknown but most likely anionic organo-I species were also identified in IC-ICP-MS chromatograms and comprised 2–10% of the total iodine. The majority of the bromine was inorganic bromide with a max. of 32% organo-Br.

  20. The effect of bromination of carbon fibers on the coefficient of thermal expansion of graphite fiber-epoxy composites

    Science.gov (United States)

    Jaworske, D. A.; Maciag, C.

    1987-01-01

    To examine the effect of bromination of carbon fibers on the coefficient of thermal expansion (CTE) of carbon fiber epoxy composites, several pristine and brominated carbon fiber-epoxy composite samples were subjected to thermomechanical analysis. The CTE's of these samples were measured in the uniaxial and transverse directions. The CTE was dominated by the fibers in the uniaxial direction, while it was dominated by the matrix in the transverse directions. Bromination had no effect on the CTE of any of the composites. In addition, the CTE of fiber tow was measured in the absence of a polymer matrix, using an extension probe. The results from this technique were inconclusive.

  1. Global atmospheric model for mercury including oxidation by bromine atoms

    Directory of Open Access Journals (Sweden)

    C. D. Holmes

    2010-12-01

    Full Text Available Global models of atmospheric mercury generally assume that gas-phase OH and ozone are the main oxidants converting Hg0 to HgII and thus driving mercury deposition to ecosystems. However, thermodynamic considerations argue against the importance of these reactions. We demonstrate here the viability of atomic bromine (Br as an alternative Hg0 oxidant. We conduct a global 3-D simulation with the GEOS-Chem model assuming gas-phase Br to be the sole Hg0 oxidant (Hg + Br model and compare to the previous version of the model with OH and ozone as the sole oxidants (Hg + OH/O3 model. We specify global 3-D Br concentration fields based on our best understanding of tropospheric and stratospheric Br chemistry. In both the Hg + Br and Hg + OH/O3 models, we add an aqueous photochemical reduction of HgII in cloud to impose a tropospheric lifetime for mercury of 6.5 months against deposition, as needed to reconcile observed total gaseous mercury (TGM concentrations with current estimates of anthropogenic emissions. This added reduction would not be necessary in the Hg + Br model if we adjusted the Br oxidation kinetics downward within their range of uncertainty. We find that the Hg + Br and Hg + OH/O3 models are equally capable of reproducing the spatial distribution of TGM and its seasonal cycle at northern mid-latitudes. The Hg + Br model shows a steeper decline of TGM concentrations from the tropics to southern mid-latitudes. Only the Hg + Br model can reproduce the springtime depletion and summer rebound of TGM observed at polar sites; the snowpack component of GEOS-Chem suggests that 40% of HgII deposited to snow in the Arctic is transferred to the ocean and land reservoirs, amounting to a net deposition flux to the Arctic of 60 Mg a−1. Summertime events of depleted Hg0 at Antarctic sites due to subsidence are much better simulated by

  2. Global atmospheric model for mercury including oxidation by bromine atoms

    Directory of Open Access Journals (Sweden)

    C. D. Holmes

    2010-08-01

    Full Text Available Global models of atmospheric mercury generally assume that OH and ozone are the main oxidants converting Hg0 to HgII and thus driving mercury deposition to ecosystems. However, thermodynamic considerations argue against the importance of these reactions. We demonstrate here the viability of atomic bromine (Br as an alternative Hg0 oxidant. We conduct a global 3-D simulation with the GEOS-Chem model assuming Br to be the sole Hg0 oxidant (Hg + Br model and compare to the previous version of the model with OH and ozone as the sole oxidants (Hg + OH/O3 model. We specify global 3-D Br concentration fields based on our best understanding of tropospheric and stratospheric Br chemistry. In both the Hg + Br and Hg + OH/O3 models, we add an aqueous photochemical reduction of HgII in cloud to impose a tropospheric lifetime for mercury of 6.5 months against deposition, as needed to reconcile observed total gaseous mercury (TGM concentrations with current estimates of anthropogenic emissions. This added reduction would not be necessary in the Hg + Br model if we adjusted the Br oxidation kinetics downward within their range of uncertainty. We find that the Hg + Br and Hg + OH/O3 models are equally capable of reproducing the spatial distribution of TGM and its seasonal cycle at northern mid-latitudes. The Hg + Br model shows a steeper decline of TGM concentrations from the tropics to southern mid-latitudes. Only the Hg + Br model can reproduce the springtime depletion and summer rebound of TGM observed at polar sites; the snowpack component of GEOS-Chem suggests that 40% of HgII deposited to snow in the Arctic is transferred to the ocean and land reservoirs, amounting to a net deposition flux of 60 Mg a−1. Summertime events of depleted Hg0 at Antarctic sites due to subsidence are much better simulated by the Hg + Br model. Model

  3. Lubiprostone: a chloride channel activator.

    Science.gov (United States)

    Lacy, Brian E; Levy, L Campbell

    2007-04-01

    In January 2006 the Food and Drug Administration approved lubiprostone for the treatment of chronic constipation in men and women aged 18 and over. Lubiprostone is categorized as a prostone, a bicyclic fatty acid metabolite of prostaglandin E1. Lubiprostone activates a specific chloride channel (ClC-2) in the gastrointestinal (GI) tract to enhance intestinal fluid secretion, which increases GI transit and improves symptoms of constipation. This article reviews the role of chloride channels in the GI tract, describes the structure, function, and pharmacokinetics of lubiprostone, and discusses clinically important data on this new medication.

  4. [Headspace GC/MS analysis of residual vinyl chloride and vinylidene chloride in polyvinyl chloride and polyvinylidene chloride products].

    Science.gov (United States)

    Ohno, Hiroyuki; Mutsuga, Motoh; Kawamura, Yoko; Suzuki, Masako; Aoyama, Taiki

    2005-02-01

    A headspace GC/MS analysis method for the simultaneous determination of residual vinyl chloride (VC) and vinylidene chloride (VDC) in polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) products was developed. A test sample was swelled overnight with N,N-dimethylacetamide in a sealed vial. The vial was incubated for 1 hour at 90 degrees C, then the headspace gas was analyzed by GC/MS using a PLOT capillary column. The recoveries from spiked PVC and PVDC samples were 90.0-112.3% for VC and 85.2-108.3% for VDC. The determination limits were 0.01 microg/g for VC and 0.06/microg/g for VDC, respectively. By this method, VC was detected in two PVC water supply pipes at the levels of 0.61 and 0.01 microg/g. On the other hand, VC and VDC were not detected in any of the food container-packages or toys tested.

  5. 1,5-Diaminotetrazolium chloride

    Directory of Open Access Journals (Sweden)

    Ling-Qiao Meng

    2010-04-01

    Full Text Available The title compound, CH5N6+·Cl−, crystallized with two indepedent 1,5-diaminotetrazolium cations and two independent chloride anions in the asymmetric unit. In the crystal, there are a number of N—H...Cl hydrogen-bonding interactions, which generate a three-dimensional network.

  6. Chloride : The queen of electrolytes?

    NARCIS (Netherlands)

    Berend, Kenrick; van Hulsteijn, Leonard Hendrik; Gans, Rijk O. B.

    2012-01-01

    Background: Channelopathies, defined as diseases that are caused by mutations in genes encoding ion channels, are associated with a wide variety of symptoms and have been documented extensively over the past decade. In contrast, despite the important role of chloride in serum, textbooks in general d

  7. Neonatal exposure to brominated flame retardant BDE-47 reduces long-term potentiation and postsynaptic protein levels in mouse hippocampus

    NARCIS (Netherlands)

    Dingemans, Milou M. L.; Ramakers, Geert M. J.; Gardoni, Fabrizio; van Kleef, Regina G. D. M.; Bergman, Ake; Di Luca, Monica; van den Berg, Martin; Westerink, Remco H. S.; Wijverberg, Henk P. M.

    2007-01-01

    BACKGROUND: Increasing environmental levels of brominated flame retardants raise concern about possible adverse effects, particularly through early developmental exposure. OBJECTIVE: The objective of this research was to investigate neturodevelopmental mechanisms underlying previously observed behav

  8. 21 CFR 173.375 - Cetylpyridinium chloride.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION Specific Usage Additives § 173.375 Cetylpyridinium chloride. Cetylpyridinium chloride (CAS Reg. No... Nutrition's Library, Food and Drug Administration, 5100 Paint Branch Pkwy., College Park, MD 20740, or...

  9. Hydroxylated polybrominated diphenyl ethers exhibit different activities on thyroid hormone receptors depending on their degree of bromination

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Xiao-Min, E-mail: rxm200318@gmail.com; Guo, Liang-Hong, E-mail: LHGuo@rcees.ac.cn; Gao, Yu, E-mail: francesscototti@gmail.com; Zhang, Bin-Tian, E-mail: nktianster@gmail.com; Wan, Bin, E-mail: binwan@rcees.ac.cn

    2013-05-01

    Polybrominated diphenyl ethers (PBDEs) have been shown to disrupt thyroid hormone (TH) functions in experimental animals, and one of the proposed disruption mechanisms is direct binding of hydroxylated PBDE (OH-PBDE) to TH receptors (TRs). However, previous data on TH receptor binding and TH activity of OH-PBDEs were very limited and sometimes inconsistent. In the present paper, we examined the binding potency of ten OH-PBDEs with different degrees of bromination to TR using a fluorescence competitive binding assay. The results showed that the ten OH-PBDEs bound to TR with potency that correlated to their bromination level. We further examined their effect on TR using a coactivator binding assay and GH3 cell proliferation assay. Different TR activities of OH-PBDEs were observed depending on their degree of bromination. Four low-brominated OH-PBDEs (2′-OH-BDE-28, 3′-OH-BDE-28, 5-OH-BDE-47, 6-OH-BDE-47) were found to be TR agonists, which recruited the coactivator peptide and enhanced GH3 cell proliferation. However, three high-brominated OH-PBDEs (3-OH-BDE-100, 3′-OH-BDE-154, 4-OH-BDE-188) were tested to be antagonists. Molecular docking was employed to simulate the interactions of OH-PBDEs with TR and identify the structural determinants for TR binding and activity. According to the docking results, low-brominated OH-PBDEs, which are weak binders but TR agonists, bind with TR at the inner side of its binding pocket, whereas high-brominated compounds, which are potent binders but TR antagonists, reside at the outer region. These results indicate that OH-PBDEs have different activities on TR (agonistic or antagonistic), possibly due to their different binding geometries with the receptor. - Highlights: ► Thyroid hormone (TH) activity of OH-PBDEs with different Br number was evaluated. ► Four different experimental approaches were employed to investigate the mechanism. ► Low-brominated OH-PBDEs were agonists, but high-brominated ones were antagonists.

  10. Progress of Carbonation in Chloride Contaminated Concretes

    OpenAIRE

    Wang, Yaocheng; Basheer, P. A.M.; Nanukuttan, S; Bai, Y.

    2016-01-01

    Concretes used in marine environment are generally under the cyclic effect of CO2 and chloride ions (Cl-). To date, the influence of carbonation on ingress of chloride ions in concretes has been widely studied; in comparison, study on the influence of Cl- on the progress of carbonation is limited. During the study, concretes were exposed to independent and combined mechanisms of carbonation and chloride ingress regimes. Profiles of apparent pH and chloride concentration were used to indicate ...

  11. Microbial reductive dehalogenation of vinyl chloride

    Energy Technology Data Exchange (ETDEWEB)

    Spormann, Alfred M [Stanford, CA; Muller, Jochen A [Baltimore, MD; Rosner, Bettina M [Berlin, DE; Von Abendroth, Gregory [Mannheim, DE; Meshulam-Simon, Galit [Los Angeles, CA; McCarty, Perry L [Stanford, CA

    2014-02-11

    Compositions and methods are provided that relate to the bioremediation of chlorinated ethenes, particularly the bioremediation of vinyl chloride by Dehalococcoides-like organisms. An isolated strain of bacteria, Dehalococcoides sp. strain VS, that metabolizes vinyl chloride is provided; the genetic sequence of the enzyme responsible for vinyl chloride dehalogenation; methods of assessing the capability of endogenous organisms at an environmental site to metabolize vinyl chloride; and a method of using the strains of the invention for bioremediation.

  12. 21 CFR 184.1426 - Magnesium chloride.

    Science.gov (United States)

    2010-04-01

    ... mineral bischofite. It is prepared by dissolving magnesium oxide, hydroxide, or carbonate in aqueous... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium chloride. 184.1426 Section 184.1426 Food... Specific Substances Affirmed as GRAS § 184.1426 Magnesium chloride. (a) Magnesium chloride (MgC12·6H2O,...

  13. Cystic Fibrosis (CF): Chloride Sweat Test

    Science.gov (United States)

    ... Old Feeding Your 1- to 2-Year-Old Cystic Fibrosis (CF) Chloride Sweat Test KidsHealth > For Parents > Cystic Fibrosis (CF) Chloride Sweat Test Print A A A ... It Is A chloride sweat test helps diagnose cystic fibrosis (CF) , an inherited disorder that makes kids sick ...

  14. 75 FR 33824 - Barium Chloride From China

    Science.gov (United States)

    2010-06-15

    ... COMMISSION Barium Chloride From China Determination On the basis of the record\\1\\ developed in the subject... order on barium chloride from China would be likely to lead to continuation or recurrence of material... Barium Chloride from China: Investigation No. 731-TA-149 (Third Review). By order of the...

  15. 75 FR 19657 - Barium Chloride From China

    Science.gov (United States)

    2010-04-15

    ... COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of... chloride from China. SUMMARY: The Commission hereby gives notice that it will proceed with a full review... revocation of the antidumping duty order on barium chloride from China would be likely to lead...

  16. 21 CFR 172.180 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... Preservatives § 172.180 Stannous chloride. The food additive stannous chloride may be safely used for color... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Stannous chloride. 172.180 Section 172.180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR...

  17. Kinetics and mechanism of the oxidative bromination of o-xylene in solution

    Energy Technology Data Exchange (ETDEWEB)

    Dorfman, Ya.A.; Emel' yanova, V.S.; Efremenko, I.G.; Doroshkevich, D.M.; Korolev, A.V.

    1988-07-01

    The kinetics of oxidative bromination of aromatic compounds have been studied in HNO/sub 3/-HBr-H/sub 2/SO/sub 4/-H/sub 2/O-O/sub 2/ solution. A kinetic equation which describes the results was derived for P/sub O/sub 2// > 5 /times/ 10/sup 4/ Pa. The equation parameters were determined at a temperature of 323 K. Quantum mechanical CNDO calculations were carried out in order to study the nature of the reactive intermediates involved: NO/sub 2/ NO(OH)/sup +/, N(OH)/sub 2//sup 2 +/, NO(OH)Br, and N(OH)/sub 2/Br/sup +/. A mechanism has been proposed to account for the oxidative bromination of aromatic compounds in HNO/sub 3/-H/sub 2/SO/sub 4/-HBr-O/sub 2/-H/sub 2/ solution.

  18. A Quaternized Polysulfone Membrane for Zinc-Bromine Redox Flow Battery

    Directory of Open Access Journals (Sweden)

    Mingqiang Li

    2014-01-01

    Full Text Available A quaternized polysulfone (QNPSU composite membrane is fabricated for zinc-bromine redox flow battery. The structure of the membrane is examined by FT-IR spectra and SEM. The conductivity of the membrane is tested by electrochemical analyzer. After a zinc-bromine battery with this composite membrane is operated at different voltage while charging and at different current while discharging to examine the performance of the membrane, it is found that the discharge voltage was 0.9672 V and the power density was 6 mW/cm2 at a current of 0.1 A, which indicated that the novel composite membrane is a promising material for the flow battery.

  19. Co-doping of Potassium and Bromine in Carbon Nanotubes: A Density Functional Theory Study

    Institute of Scientific and Technical Information of China (English)

    XIAO Yong; YAN xiao-Hong; DING Jian-Wen

    2007-01-01

    We investigate the co-doping of potassium and bromine in singlewalled carbon nanotubes (SWCNTs)and doublewalled carbon nanotubes(DWCNTs)based on density functional theory.In the co-doped(6,O)SWCNTs,the 4s electron of potassium is transferred to nanotube and Br,leading to the n-type feature of SWCNTs.When potassium is intercalated into inner tube and bromine is put on outer tube,the positive and negative charges reside on the outer and inner tubes of the(7.0)@(16,0)DWCNT,respectively.It is expected that DWCNTs would be an ideal candidate for p-n junction and diode applications.

  20. Analysis and occurrence of emerging brominated flame retardants in the Llobregat River basin

    Science.gov (United States)

    Guerra, Paula; Eljarrat, Ethel; Barceló, Damià

    2010-03-01

    SummaryIn response to increasing international regulations on brominated flame retardants (BFR) formulations, alternative additive flame retardants for achieving commercial product fire safety standards are being developed and used. Some of these non-BDE (brominated diphenyl ethers) BFRs are pentabromoethylbenzene (PBEB), hexabromobenzene (hexaBBz), and decabromodiphenylethane (deBDethane). The present study investigated the occurrence of these emerging BFRs, together with 38 BDE congeners (from di- to deca-BDE) in sediments sampled from different points along Llobregat basin (Spain) in three different sampling campaigns between 2005 and 2006. Emerging BFRs were detected in all sediment samples analyzed, at concentrations ranging from 3.1 to 9.6 ng/g for PBEB, from 0.4 to 2.4 ng/g for hexaBBz and from 4.8 to 23 ng/g for deBDethane. These levels are lower than concentrations obtained for PBDEs (from nd to 82 ng/g).

  1. A review of mathematical modeling of the zinc/bromine flow cell and battery

    Science.gov (United States)

    Evans, T. I.; White, R. E.

    1987-11-01

    Mathematical models which have been developed to study various aspects of the zinc/bromine cell and stack of cells are reviewed. Development of these macroscopic models begins with a material balance, a transport equation which includes a migration term for charged species in an electric field, and an electrode kinetic expression. Various types of models are discussed: partial differential equation models that can be used to predict current and potential distributions, an algebraic model that includes shunt currents and associated energy losses and can be used to determine the optimum resistivity of an electrolyte, and ordinary differential equation models that can be used to predict the energy efficiency of the cell as a function of the state of charge. These models have allowed researchers to better understand the physical phenomena occurring within parallel plate electrochemical flow reactors and have been instrumental in the improvement of the zinc/bromine cell design. Suggestions are made for future modeling work.

  2. The effect of representing bromine from VSLS on the simulation and evolution of Antarctic ozone

    Science.gov (United States)

    Oman, Luke D.; Douglass, Anne R.; Salawitch, Ross J.; Canty, Timothy P.; Ziemke, Jerald R.; Manyin, Michael

    2016-09-01

    We use the Goddard Earth Observing System Chemistry-Climate Model, a contributor to both the 2010 and 2014 World Meteorological Organization Ozone Assessment Reports, to show that inclusion of 5 parts per trillion (ppt) of stratospheric bromine (Bry) from very short lived substances (VSLS) is responsible for about a decade delay in ozone hole recovery. These results partially explain the significantly later recovery of Antarctic ozone noted in the 2014 report, as bromine from VSLS was not included in the 2010 Assessment. We show multiple lines of evidence that simulations that account for VSLS Bry are in better agreement with both total column BrO and the seasonal evolution of Antarctic ozone reported by the Ozone Monitoring Instrument on NASA's Aura satellite. In addition, the near-zero ozone levels observed in the deep Antarctic lower stratospheric polar vortex are only reproduced in a simulation that includes this Bry source from VSLS.

  3. Formation pathways of brominated products from benzophenone-4 chlorination in the presence of bromide ions

    Institute of Scientific and Technical Information of China (English)

    Ming Xiao; Dongbin Wei; Liping Li; Qi Liu; Huimin Zhao; Yuguo Du

    2014-01-01

    The brominated products,formed in chlorination treatment of benzophenone-4 in the presence of bromide ions,were identified,and the formation pathways were proposed.Under disinfection conditions,benzophenone-4 would undertake electrophilic substitution generating mono-or di-halogenated products,which would be oxidized to esters and further hydrolyzed to phenol derivatives.The generated catechol intermediate would be transformed into furan-like heterocyclic product.The product species were pH-dependent,while benzophenone-4 ehmination was chlorine dose-dependent.When the chlorination treatment was performed on ambient water spiked with benzophenone-4 and bromide ions,most of brominated byproducts could be detected,and the acute toxicity significantly increased as well.

  4. Improved charge carrier lifetime in planar perovskite solar cells by bromine doping

    OpenAIRE

    Kiermasch, David; Rieder, Philipp; Tvingstedt, Kristofer; Baumann, Andreas; Dyakonov, Vladimir

    2016-01-01

    The charge carrier lifetime is an important parameter in solar cells as it defines, together with the mobility, the diffusion length of the charge carriers, thus directly determining the optimal active layer thickness of a device. Herein, we report on charge carrier lifetime values in bromine doped planar methylammonium lead iodide (MAPbI3) solar cells determined by transient photovoltage. The corresponding charge carrier density has been derived from charge carrier extraction. We found incre...

  5. Tropospheric bromine chemistry: implications for present and pre-industrial ozone and mercury

    Directory of Open Access Journals (Sweden)

    J. P. Parrella

    2012-04-01

    Full Text Available We present a new model for the global tropospheric chemistry of inorganic bromine (Bry coupled to oxidant-aerosol chemistry in the GEOS-Chem chemical transport model (CTM. Sources of tropospheric Bry include debromination of sea-salt aerosol, photolysis and oxidation of short-lived bromocarbons, and transport from the stratosphere. Comparison to a GOME-2 satellite climatology of tropospheric BrO columns shows that the model can reproduce the observed increase of BrO with latitude, the northern mid-latitudes maximum in winter, and the Arctic maximum in spring. This successful simulation is contingent on the HOBr + HBr reaction taking place in aqueous aerosols and ice clouds. Bromine chemistry in the model decreases tropospheric ozone concentrations by <1−8 nmol mol−1 (6.5% globally, with the largest effects in the northern extratropics in spring. The global mean tropospheric OH concentration decreases by 4%. Inclusion of bromine chemistry improves the ability of global models (GEOS-Chem and p-TOMCAT to simulate observed 19th-century ozone and its seasonality. Bromine effects on tropospheric ozone are comparable in the present-day and pre-industrial atmospheres so that estimates of anthropogenic radiative forcing are minimally affected. Br atom concentrations are 40% higher in the pre-industrial atmosphere due to lower ozone, which would decrease by a factor of 2 the atmospheric lifetime of elemental mercury against oxidation by Br. This suggests that historical anthropogenic mercury emissions may have mostly deposited to northern mid-latitudes, enriching the corresponding surface reservoirs. The persistent rise in background surface ozone at northern mid-latitudes during the past decades could possibly contribute to the observations of elevated mercury in subsurface waters of the North Atlantic.

  6. Brominated and organophosphate flame retardants in selected consumer products on the Japanese market in 2008

    Energy Technology Data Exchange (ETDEWEB)

    Kajiwara, Natsuko, E-mail: kajiwara.natsuko@nies.go.jp [Research Center for Material Cycles and Waste Management, National Institute for Environmental Studies, 16-2 Onogawa, Tsukuba, Ibaraki 305-8506 (Japan); Noma, Yukio; Takigami, Hidetaka [Research Center for Material Cycles and Waste Management, National Institute for Environmental Studies, 16-2 Onogawa, Tsukuba, Ibaraki 305-8506 (Japan)

    2011-09-15

    Highlights: {yields} We examined the flame retardants in electronics, curtains, wallpaper and insulator. {yields} Use of alternative brominated and organophosphate flame retardants was suggested. {yields} All the products investigated also contained PBDEs, TBBPA and polybromophenols. {yields} Incorporation of recycled materials containing hazardous substance was suggested. - Abstract: The concentrations of traditional brominated flame retardants (BFRs) and organophosphate flame retardants (OPFRs) in new consumer products, including electronic equipment, curtains, wallpaper, and building materials, on the Japanese market in 2008 were investigated. Although some components of the electronic equipment contained bromine at concentrations on the order of percent by weight, as indicated by X-ray fluorescence analysis, the bromine content could not be fully accounted for by the BFRs analyzed in this study, which included polybrominated diphenylethers, decabromodiphenyl ethane, tetrabromobisphenol A, polybromophenols, and hexabromocyclododecanes. These results suggest the use of alternative BFRs such as newly developed formulations derived from tribromophenol, tetrabromobisphenol A, or both. Among the 11 OPFRs analyzed, triphenylphosphate was present at the highest concentrations in all the products investigated, which suggests the use of condensed-type OPFRs as alternative flame retardants, because they contain triphenylphosphate as an impurity. Tripropylphosphate was not detected in any samples; and trimethylphosphate, tributyl tris(2-butoxyethyl)phosphate, and tris(1,3-dichloro-2-propyl)phosphate were detected in only some components and at low concentrations. Note that all the consumer products evaluated in this study also contained traditional BFRs in amounts that were inadequate to impart flame retardancy, which implies the incorporation of recycled plastic materials containing BFRs that are of global concern.

  7. Bromine-catalyzed conversion of CO2 and epoxides to cyclic carbonates under continuous flow conditions.

    Science.gov (United States)

    Kozak, Jennifer A; Wu, Jie; Su, Xiao; Simeon, Fritz; Hatton, T Alan; Jamison, Timothy F

    2013-12-11

    A continuous method for the formation of cyclic carbonates from epoxides and carbon dioxide (CO2) is described. The catalysts used are inexpensive and effective in converting the reagents to the products in a residence time (t(R)) of 30 min. The cyclic carbonate products are obtained in good to excellent yield (51-92%). On the basis of a series of kinetics experiments, we propose a reaction mechanism involving epoxide activation by electrophilic bromine and CO2 activation by an amide.

  8. Tropospheric bromine chemistry: implications for present and pre-industrial ozone and mercury

    Directory of Open Access Journals (Sweden)

    J. P. Parrella

    2012-08-01

    Full Text Available We present a new model for the global tropospheric chemistry of inorganic bromine (Bry coupled to oxidant-aerosol chemistry in the GEOS-Chem chemical transport model (CTM. Sources of tropospheric Bry include debromination of sea-salt aerosol, photolysis and oxidation of short-lived bromocarbons, and transport from the stratosphere. Comparison to a GOME-2 satellite climatology of tropospheric BrO columns shows that the model can reproduce the observed increase of BrO with latitude, the northern mid-latitudes maximum in winter, and the Arctic maximum in spring. This successful simulation is contingent on the HOBr + HBr reaction taking place in aqueous aerosols and ice clouds. Bromine chemistry in the model decreases tropospheric ozone mixing ratios by <1–8 nmol mol−1 (6.5% globally, with the largest effects in the northern extratropics in spring. The global mean tropospheric OH concentration decreases by 4%. Inclusion of bromine chemistry improves the ability of global models (GEOS-Chem and p-TOMCAT to simulate observed 19th-century ozone and its seasonality. Bromine effects on tropospheric ozone are comparable in the present-day and pre-industrial atmospheres so that estimates of anthropogenic radiative forcing are minimally affected. Br atom concentrations are 40% higher in the pre-industrial atmosphere due to lower ozone, which would decrease by a factor of 2 the atmospheric lifetime of elemental mercury against oxidation by Br. This suggests that historical anthropogenic mercury emissions may have mostly deposited to northern mid-latitudes, enriching the corresponding surface reservoirs. The persistent rise in background surface ozone at northern mid-latitudes during the past decades could possibly contribute to the observations of elevated mercury in subsurface waters of the North Atlantic.

  9. Preparation of hydrophilic vinyl chloride copolymer hollow fiber membranes with antifouling properties

    Science.gov (United States)

    Rajabzadeh, Saeid; Sano, Rie; Ishigami, Toru; Kakihana, Yuriko; Ohmukai, Yoshikage; Matsuyama, Hideto

    2015-01-01

    Hydrophilic vinyl chloride copolymer hollow fiber membranes with antifouling properties were prepared from brominated vinyl chloride-hydroxyethyl methacrylate copolymer (poly(VC-co-HEMA-Br)). The base membrane was grafted with two different zwitterionic monomers, (2-methacryloyloxyethylphosphorylcholine) (MPC) and [2-(methacryloyloxy) ethyl] dimethyl (3-sulfopropyl) ammonium hydroxide) (MEDSAH), and poly(ethylene glycol) methyl ether methacrylate (PEGMA). The effect of the grafting on the base membrane hydrophilicity and antifouling properties was investigated. For comparison of the results, the pure water permeabilities and pore sizes at the outer surfaces of the grafted hollow fiber membranes were controlled to be similar. A poly(VC-co-HEMA-Br) hollow fiber membrane with similar pure water permeability and pore size was also prepared as a control membrane. A BSA solution was used as a model fouling solution for evaluation of the antifouling properties. Grafting with zwitterionic monomers and PEGMA improved the antifouling properties compared with the control membrane. The PEGMA grafted membrane showed the best antifouling properties among the grafted membranes

  10. On the age of stratospheric air and inorganic chlorine and bromine release

    Science.gov (United States)

    Daniel, J. S.; Schauffler, S. M.; Pollock, W. H.; Solomon, S.; Weaver, A.; Heidt, L. E.; Garcia, R. R.; Atlas, E. L.; Vedder, J. F.

    1996-07-01

    We estimate the average transport time from the tropical tropopause to various regions of the northern hemisphere lower stratosphere (stratospheric age) using simultaneous mixing ratio measurements of CFC-115 and CO2 measured by the Whole Air Sampler (WAS) during Airborne Arctic Stratospheric Expedition II (AASE II). Our inferred ages are consistent with those presented in previous studies. We discuss sources of uncertainties that affect age estimates in general, as well as specific uncertainties arising from inferring ages using CO2 and CFC-115 abundances. We infer inorganic chlorine (Cly) and bromine (Bry) at various lower stratospheric locations using the WAS organic chlorine and bromine measurements in combination with modeled tropospheric halocarbon trends and with our estimated ages. Inferred Cly and Bry abundances generally increase with increasing latitude and altitude. For our analyzed locations inside the polar vortex, we estimate a maximum Cly abundance of about 2.7 parts per billion by volume (ppbv) and a maximum Bry abundance of about 13.7 parts per trillion by volume (pptv). The locations of these maxima correspond to an average N2O mixing ratio of about 100 ppbv, and to a fractional dissociation of organic chlorine and bromine of 0.85 and 0.90, respectively. Finally, we discuss the expected future limitations of using CFC-115 to estimate stratospheric age due to the production limitations prescribed by the amendments and adjustments to the Montreal Protocol.

  11. Examination of the kinetics of degradation of the antineoplastic drug 5-fluorouracil by chlorine and bromine.

    Science.gov (United States)

    Li, Wei; Tanumihardja, Jessica; Masuyama, Takaaki; Korshin, Gregory

    2015-01-23

    This study examined the degradation of the widely used antineoplastic drug 5-fluorouracil (5FU) by chlorine and bromine. 5FU was determined to interact readily with free chlorine and bromine but was stable in the presence of chloramine. The removal of 5FU followed a second-order kinetic pattern. Apparent rates (kapp) of 5FU removal by chlorine and bromine were strongly pH dependent and had maximum 14.8M(-1)s(-1) and 1.9×10(3)M(-1)s(-1)kapp values, respectively at pH 7. Modeling of the dependence of the kapp values vs. pH indicated the presence of a relatively acidic (pK 6.4 vs. 8.5 of 5FU per se) 5FU intermediate generated in the presence of halogen species. Spectrophotometric measurements confirmed the increased acidity of 5FU chlorination products and allowed proposing a degradation pathway of 5FU by chlorine. This pathway suggests that 5FU chlorination proceeds via chlorine incorporation at the 6th carbon in the heterocyclic ring of 5FU.

  12. Effects of Assistant Solvents and Mixing Intensity on the Bromination Process of Butyl Rubber

    Institute of Scientific and Technical Information of China (English)

    王伟; 邹海魁; 初广文; 向阳; 彭晗; 陈建峰

    2014-01-01

    A slow bromination process of butyl rubber (IIR) suffers from low efficiency and low selectivity (S) of target-product. To obtain suitable approach to intensify the process, effects of assistant solvents and mixing inten-sity on the bromination process were systemically studied in this paper. The reaction process was found constantly accelerated with the increasing dosage and polarity of assistant solvent. Hexane with 30%(by volume) dichloro-methane was found as the suitable solvent component, where the stable conversion of 1,4-isoprene transferring to target product (xA1s) of 80.2%and the corresponding S of 91.2%were obtained in 5 min. The accelerated reaction process was demonstrated being remarkably affected by mixing intensity until the optimal stirring rate of 1100 r·min-1 in a stirred tank reactor. With better mixing condition, a further intensification of the process was achieved in a ro-tating packed bed (RPB) reactor, where xA1s of 82.6% and S of 91.9% were obtained in 2 min. The usage of the suitable solvent component and RPB has potential application in the industrial bromination process intensification.

  13. Computer simulation of the cluster destruction of stratospheric ozone by bromine

    Institute of Scientific and Technical Information of China (English)

    A.E.Galashev; O.R.Rakhmanova

    2012-01-01

    The interaction of (Br-)i(H2O)50-i,0≤i≤6 clusters with oxygen and ozone molecules is investigated by the method of molecular dynamics simulation.The ozone molecules as well as the bromine ions do not leave the cluster during the calculation of 25 ps.The ability of the cluster containing molecular oxygen to absorb the infrared (IR)radiation is reduced in the frequency range of 0 ≤ ω ≤ 3500 cm-1 when the number of the bromine ions in the cluster grows.The intensity of the Raman spectrum is not changed significantly when the Br-ions are added to the ozonecontaining system.The power of the emitted IR radiation is increased when the number of bromine ions grows in the oxygen-containing system.The data obtained in this study on the IR and the Raman spectra of the water clusters that contain ozone,oxygen,and Br-can be used to develop an investigation of the mechanisms of ozone depletion.

  14. Discrimination of hexabromocyclododecane from new polymeric brominated flame retardant in polystyrene foam by nuclear magnetic resonance.

    Science.gov (United States)

    Jeannerat, Damien; Pupier, Marion; Schweizer, Sébastien; Mitrev, Yavor Nikolaev; Favreau, Philippe; Kohler, Marcel

    2016-02-01

    Hexabromocyclododecane (HBCDD) is a brominated flame retardant (BFR) and major additive to polystyrene foam thermal insulation that has recently been listed as a persistent organic pollutant by the Stockholm Convention. During a 2013/2014 field analytical survey, we measured HBCDD content ranging from 0.2 to 2.4% by weight in 98 polystyrene samples. Liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) analyses indicated that expandable (EPS) and extruded (XPS) polystyrene foams significantly differed in the α/γ HBCDD isomer ratio, with a majority of α and γ isomers in XPS and EPS, respectively. Interestingly, this technique indicated that some recent materials did not contain HBCDD, but demonstrated bromine content when analysed with X-ray fluorescence (XRF). Further investigation by Nuclear Magnetic Resonance (NMR) was able to discriminate between the BFRs present. In addition to confirming the absence or presence of HBCDD in polystyrene samples, high-field NMR spectroscopy provided evidence of the use of brominated butadiene styrene (BBS) as copolymer in the production of polystyrene. Use of this alternative flame retardant is expected to cause fewer health and environmental concerns. Our results highlight a trend towards the use of copolymerized BFRs as an alternative to HBCDD in polystyrene foam boards. In addition to providing a rapid NMR method to identify polymeric BFR, our analytical approach is a simple method to discriminate between flame-retardants in polystyrene foam insulating materials.

  15. Mechanochemical conversion of brominated POPs into useful oxybromides: a greener approach

    Science.gov (United States)

    Cagnetta, Giovanni; Liu, Han; Zhang, Kunlun; Huang, Jun; Wang, Bin; Deng, Shubo; Wang, Yujue; Yu, Gang

    2016-06-01

    Brominated organic pollutants are considered of great concern for their adverse effect on human health and the environment, so an increasing number of such compounds are being classified as persistent organic pollutants (POPs). Mechanochemical destruction is a promising technology for POPs safe disposal because it can achieve their complete carbonization by solvent-free high energy ball milling at room temperature. However, a large amount of co-milling reagent usually is necessary, so a considerable volume of residue is produced. In the present study a different approach to POPs mechanochemical destruction is proposed. Employing stoichiometric quantities of Bi2O3 or La2O3 as co-milling reagent, brominated POPs are selectively and completely converted into their corresponding oxybromides (i.e. BiOBr and LaOBr), which possess very peculiar properties and can be used for some actual and many more potential applications. In this way, bromine is beneficially reused in the final product, while POPs carbon skeleton is safely destroyed to amorphous carbon. Moreover, mechanochemical destruction is employed in a greener and more sustainable manner.

  16. Determination of bromine in regulated foods with a field-portable X-ray fluorescence analyzer.

    Science.gov (United States)

    Anderson, David L

    2009-01-01

    A field-portable X-ray fluorescence analyzer, factory-calibrated for soil analysis, was used to measure bromine (Br) mass fractions in reference materials, flour, bakery products, malted barley, selected U.S. Food and Drug Administration Total Diet Study foods, and other food products. By using a calibration based on instrumental neutron activation analysis results for Br in reference materials, accurate quantitative results, confirmed by z-scores, could be obtained for mass fractions of about 2-55 mg/kg. These results confirmed accuracy of results (with larger uncertainties) obtained by applying a simple correction factor to the analyzer's output value. Results showed that very short analysis times (content at regulatory levels for brominated and enriched brominated flour (24 mg/kg Br) and whole wheat flour and bakery products (36 mg/kg Br). Feasibility for determination of Br in malted barley at the regulatory level (75 mg/kg Br) was demonstrated, but quantitative results at that level could not be assured because no reference material with a suitable mass fraction was available. Br mass fractions for all foods tested were well below regulatory levels.

  17. Brominated and organophosphate flame retardants in selected consumer products on the Japanese market in 2008.

    Science.gov (United States)

    Kajiwara, Natsuko; Noma, Yukio; Takigami, Hidetaka

    2011-09-15

    The concentrations of traditional brominated flame retardants (BFRs) and organophosphate flame retardants (OPFRs) in new consumer products, including electronic equipment, curtains, wallpaper, and building materials, on the Japanese market in 2008 were investigated. Although some components of the electronic equipment contained bromine at concentrations on the order of percent by weight, as indicated by X-ray fluorescence analysis, the bromine content could not be fully accounted for by the BFRs analyzed in this study, which included polybrominated diphenylethers, decabromodiphenyl ethane, tetrabromobisphenol A, polybromophenols, and hexabromocyclododecanes. These results suggest the use of alternative BFRs such as newly developed formulations derived from tribromophenol, tetrabromobisphenol A, or both. Among the 11 OPFRs analyzed, triphenylphosphate was present at the highest concentrations in all the products investigated, which suggests the use of condensed-type OPFRs as alternative flame retardants, because they contain triphenylphosphate as an impurity. Tripropylphosphate was not detected in any samples; and trimethylphosphate, tributyl tris(2-butoxyethyl)phosphate, and tris(1,3-dichloro-2-propyl)phosphate were detected in only some components and at low concentrations. Note that all the consumer products evaluated in this study also contained traditional BFRs in amounts that were inadequate to impart flame retardancy, which implies the incorporation of recycled plastic materials containing BFRs that are of global concern.

  18. Heterogeneous processing of bromine compounds by atmospheric aerosols: Relation to the ozone budget

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, J.M.; Henson, B.F.; Dubey, M.K.; Casson, J.L.; Johal, M.S. [Los Alamos National Lab., NM (US); Wilson, K.R. [Univ. of California, Berkeley, CA (US)

    1998-11-01

    This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The depletion of ozone, particularly above Antarctica, has been investigated extensively to formulate public policy on the use of halocarbons. While it has been shown that heterogeneous reactions of chlorine compounds on stratospheric particulates cause the ozone hole, little is known of the analogous bromine mechanisms, even though it has been recognized for two decades that catalytic destruction of ozone by bromine could be more efficient than chlorine. Furthermore, field measurements and modeling calculations suggest that these heterogeneous (gas/surface) reactions are not restricted to the Antarctic regions but occur globally. The authors have performed laboratory measurements of the uptake of bromine compounds and other halogens on simulated stratospheric aerosols to help elucidate their role in catalytic ozone destruction cycles. Their studies contribute to the data base required to make assessments of the effects of human activities on global change, including the Montreal Protocol.

  19. Removal of brominated flame retardant from electrical and electronic waste plastic by solvothermal technique.

    Science.gov (United States)

    Zhang, Cong-Cong; Zhang, Fu-Shen

    2012-06-30

    Brominated flame retardants (BFRs) in electrical and electronic (E&E) waste plastic are toxic, bioaccumulative and recalcitrant. In the present study, tetrabromobisphenol A (TBBPA) contained in this type of plastic was tentatively subjected to solvothermal treatment so as to obtain bromine-free plastic. Methanol, ethanol and isopropanol were examined as solvents for solvothermal treatment and it was found that methanol was the optimal solvent for TBBPA removal. The optimum temperature, time and liquid to solid ratio for solvothermal treatment to remove TBBPA were 90°C, 2h and 15:1, respectively. After the treatment with various alcohol solvents, it was found that TBBPA was finally transferred into the solvents and bromine in the extract was debrominated catalyzed by metallic copper. Bisphenol A and cuprous bromide were the main products after debromination. The morphology and FTIR properties of the plastic were generally unchanged after the solvothermal treatment indicating that the structure of the plastic maintained after the process. This work provides a clean and applicable process for BFRs-containing plastic disposal.

  20. A satellite based study of tropospheric bromine explosion events and their linkages to polar cyclone development

    Science.gov (United States)

    Blechschmidt, Anne-Marlene; Richter, Andreas; Burrows, John P.; Kaleschke, Lars; Strong, Kimberly; Theys, Nicolas; Weber, Mark; Zhao, Xiaoyi; Zien, Achim; Hodges, Kevin I.

    2016-04-01

    Intense, cyclone-like shaped plumes of tropospheric bromine monoxide (BrO) are regularly observed by the UV-vis satellite instruments GOME-2/MetOp-A and SCIAMACHY/Envisat over Arctic and Antarctic sea ice in polar spring. The plumes are associated with an autocatalytic chemical chain reaction involving tropospheric ozone depletion and initiated by the release of bromine from cold brine-covered ice or snow to the atmosphere. This influences atmospheric chemistry as it affects the oxidising capacity of the troposphere through OH production and may also influence the local weather/temperature of the polar atmosphere, as ozone is a major greenhouse gas. Here, we make combined use of satellite retrievals and numerical model simulations to study individual BrO plume cases in the polar atmosphere. In agreement with previous studies, our analysis shows that the plumes are often transported by high latitude cyclones, sometimes over several days despite the short atmospheric lifetime of BrO. Moreover, general characteristics of bromine explosion events linked to transport by polar weather systems, such as frequency, spatial distribution and favourable weather conditions are derived based on a new detection method. Our results show that BrO cyclone transport events are by far more common in the Antarctic than in the Arctic.

  1. Enhanced crystal grain size by bromine doping in electrodeposited Cu{sub 2}O

    Energy Technology Data Exchange (ETDEWEB)

    Han Kunhee; Kang Feng [Department of Electrical Engineering, University of Texas at Arlington, Arlington, TX 76019 (United States); Han Xiaofei [Department of Material Science and Engineering, University of Texas at Arlington, Arlington, TX 76019 (United States); Tao Meng, E-mail: meng.tao@asu.edu [Department of Electrical Engineering, University of Texas at Arlington, Arlington, TX 76019 (United States)

    2012-06-01

    Extremely large crystal grains are obtained by bromine doping in electrodeposited Cu{sub 2}O on indium tin oxide (ITO) substrate through an acetate bath. The grains are as large as 10,000 {mu}m{sup 2} in area, or {approx} 100 {mu}m in linear dimension, while the film is only 1-5 {mu}m thick. The enhanced grain size is explained by the effect of over-potential for the Cu{sup 2+}/Cu{sup +} redox couple on nucleation density of Cu{sub 2}O on ITO substrate. The over-potential is a function of several deposition conditions including solution pH, deposition potential, deposition temperature, bromine precursor concentration, and copper precursor concentration. In addition, undoped Cu{sub 2}O displays a high resistivity of 100 M{Omega}cm. Bromine doping in Cu{sub 2}O significantly reduces the resistivity to as low as 42 {Omega}cm after vacuum annealing. Br-doped Cu{sub 2}O shows n-type behavior. - Highlights: Black-Right-Pointing-Pointer Extremely large crystal grains ({approx} 100 {mu}m) achieved in electrodeposited Br-doped Cu{sub 2}O. Black-Right-Pointing-Pointer Large grains reduce carrier recombination and carrier scattering at grain boundaries. Black-Right-Pointing-Pointer N-type behavior demonstrated in naturally p-type Cu{sub 2}O by Br doping.

  2. MISCIBILITY AND MORPHOLOGY OF THIN FILMS OF BLENDS OF POLYSTYRENE WITH BROMINATED POLYSTYRENES: EFFECTS OF VARYING THE MOLECULAR WEIGHT,BROMINATION DEGREE AND ANNEALING

    Institute of Scientific and Technical Information of China (English)

    Rui Song; De-bin Yang; Ling-hao He; Guang-tao Yao

    2006-01-01

    Thin films of incompatible polymer blends can form a variety of structures during preparation and subsequent annealing process. For the polymer blend system consisting of polystyrene and poly(styrene-co-p-bromo-styrene), I.e.,PS/PBrxS, its compatibility could be adjusted by varying the degree of bromination and the molecular weight of both components comprised. In this paper, surface chemical compositions of the cast and the annealing films were investigated by X-ray photoelectron spectroscopy (XPS) and contact angle measurement; meanwhile, surface topographical changes are followed by atomic force microscopy (AFM). In addition, substantial attention was paid to the effect of annealing on the morphologic variations induced by phase separation and/or dewetting of the thin film. Moreover, the influences of the molecular weight, Mw, as well as the brominated degree, x%, on the sample surface are explored systematically, and the corresponding observations are explained in virtue of the Flory-Huggins theory, along with the dewetting of the polymer thin film.

  3. Study Of The Fundamental Physical Principles in Atmospheric Modeling Based On Identification Of Atmosphere - Climate Control Factors: Bromine Explosion At The Polar Arctic Sunrise

    OpenAIRE

    Iudin, M.

    2007-01-01

    We attempt is to provide accumulated evidence and qualitative understanding of the associated atmospheric phenomena of the Arctic bromine explosion and their role in the functioning of the biotic Earth. We rationalize the empirical expression of the bromine influx into atmospheric boundary layer and calculate total amounts of the tropospheric BrO and Bry of the Arctic origin. Based on the quantities and partitioning of the reactive bromine species, we estimate the biogeochemical parametric co...

  4. Oxomemazine hydro­chloride

    OpenAIRE

    Siddegowda, M. S.; Butcher, Ray J.; Mehmet Akkurt; Yathirajan, H.S.; Ramesh, A. R.

    2011-01-01

    In the title compound [systematic name: 3-(5,5-dioxophenothiazin-10-yl)-N,N,2-trimethylpropanaminium chloride], C18H23N2O2S+·Cl−, the dihedral angle between the two outer aromatic rings of the phenothiazine unit is 30.5 (2)°. In the crystal, the components are linked by N—H...Cl and C—H...Cl hydrogen bonds and C—H...π interactions.

  5. Shock compression of polyvinyl chloride

    Science.gov (United States)

    Neogi, Anupam; Mitra, Nilanjan

    2016-04-01

    This study presents shock compression simulation of atactic polyvinyl chloride (PVC) using ab-initio and classical molecular dynamics. The manuscript also identifies the limits of applicability of classical molecular dynamics based shock compression simulation for PVC. The mechanism of bond dissociation under shock loading and its progression is demonstrated in this manuscript using the density functional theory based molecular dynamics simulations. The rate of dissociation of different bonds at different shock velocities is also presented in this manuscript.

  6. Developing chloride resisting concrete using PFA

    Energy Technology Data Exchange (ETDEWEB)

    Dhir, R.K.; El-Mohr, M.A.K.; Dyer, T.D. [Univ. of Dundee (United Kingdom). Dept. of Civil Engineering

    1997-11-01

    PFA concrete mixes were designed to optimize resistance to chloride ingress. Chloride binding capacity, intrinsic permeability and their concomitant influence on the coefficient of chloride diffusion have been investigated. PFA replacements up to 67% and exposure concentrations of 0.1, 0.5, 1.0 and 5.0 mole/liter were used. Chloride binding capacity was found to increase with increasing PFA replacement up to 50% and to then decline. It increased with chloride exposure concentration as well as water/binder ratio. The coefficient of chloride diffusion of concrete samples was found to be dependent on both the intrinsic permeability of the concrete and the ability of its cement matrix to bind chlorides.

  7. Salt, chloride, bleach, and innate host defense.

    Science.gov (United States)

    Wang, Guoshun; Nauseef, William M

    2015-08-01

    Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense.

  8. Bromine monoxide / sulphur dioxide ratios in relation to volcanological observations at Mt. Etna 2006–2009

    Directory of Open Access Journals (Sweden)

    G. Giuffrida

    2012-12-01

    Full Text Available Over a 3-yr period, from 2006 to 2009, frequent scattered sunlight DOAS measurements were conducted at Mt. Etna at a distance of around 6 km downwind from the summit craters. During the same period and in addition to these measurements, volcanic observations were made by regularly visiting various parts of Mt. Etna. Here, results from these measurements and observations are presented and their relation is discussed. The focus of the investigation is the bromine monoxide/sulphur dioxide (BrO / SO2 ratio, and its variability in relation to volcanic processes. That the halogen/sulphur ratio can serve as a precursor or indicator for the onset of eruptive activity was already proposed by earlier works (e.g. Noguchi and Kamiya 1963; Menyailov, 1975; Pennisi and Cloarec, 1998; Aiuppa et al., 2002. However, there is still a limited understanding today because of the complexity with which halogens are released, depending on magma composition and degassing conditions. Our understanding of these processes is far from complete, for example of the rate and mechanism of bubble nucleation, growth and ascent in silicate melts (Carroll and Holloway, 1994, the halogen vapour-melt partitioning and the volatile diffusivity in the melt (Aiuppa et al., 2009. With this study we aim to add one more piece to the puzzle of what halogen/sulphur ratios might tell about volcanic activities. Our data set shows an increase of the BrO / SO2 ratio several weeks prior to an eruption, followed by a decline before and during the initial phase of eruptive activities. Towards the end of activity or shortly thereafter, the ratio increases to baseline values again and remains more or less constant during quiet phases. To explain the observed evolution of the BrO / SO2 ratio, a first empirical model is proposed. This model suggests that bromine, unlike chlorine and fluorine, is less soluble in the magmatic melt than sulphur. By using the DOAS method to determine SO2, we actually

  9. Brominated flame retardants and organochlorine pollutants in eggs of little owls (Athene noctua) from Belgium

    Energy Technology Data Exchange (ETDEWEB)

    Jaspers, Veerle [Department of Biology, University of Antwerp, Campus Drie Eiken, Universiteitsplein 1, 2610 Wilrijk (Belgium); Covaci, Adrian [Toxicological Centre, University of Antwerp, Campus Drie Eiken, Universiteitsplein 1, 2610 Wilrijk (Belgium)]. E-mail: adrian.covaci@ua.ac.be; Maervoet, Johan [Toxicological Centre, University of Antwerp, Campus Drie Eiken, Universiteitsplein 1, 2610 Wilrijk (Belgium); Dauwe, Tom [Department of Biology, University of Antwerp, Campus Drie Eiken, Universiteitsplein 1, 2610 Wilrijk (Belgium); Voorspoels, Stefan [Toxicological Centre, University of Antwerp, Campus Drie Eiken, Universiteitsplein 1, 2610 Wilrijk (Belgium); Schepens, Paul [Toxicological Centre, University of Antwerp, Campus Drie Eiken, Universiteitsplein 1, 2610 Wilrijk (Belgium); Eens, Marcel [Department of Biology, University of Antwerp, Campus Drie Eiken, Universiteitsplein 1, 2610 Wilrijk (Belgium)

    2005-07-15

    Residues of brominated diphenylethers (PBDEs), organochlorinated pesticides (OCPs) and polychlorinated biphenyls (PCBs) were measured in 40 eggs of little owls (Athene noctua), a terrestrial top predator from Belgium. The major organohalogens detected were PCBs (median 2,600 ng/g lipid, range 790-23000 ng/g lipid). PCB 153,138/163, 170, 180 and 187 were the predominant congeners and constituted 71% of total sum PCBs. PBDEs were measurable in all samples, but their concentrations were much lower than for PCBs, with a range from 29-572 ng/g lipid (median 108 ng/g lipid). The most prevalent PBDE congeners in little owl egg samples were BDE 47, 99 and 153. This profile differs from the profile in marine bird species, for which BDE 47 was the dominant congener, indicating that terrestrial birds may be more exposed to higher brominated BDE congeners than marine birds. The fully brominated BDE 209 could be detected in one egg sample (17 ng/g lipid), suggesting that higher brominated BDEs may accumulate in terrestrial food chains. Brominated biphenyl (BB) 153 was determined in all egg samples, with levels ranging from 0.6 to 5.6 ng/g lipid (median 1.3 ng/g lipid). Additionally, hexabromocyclododecane (HBCD) could be identified and quantified in only two eggs at levels of 20 and 50 ng/g lipid. OCPs were present at low concentrations, suggesting a rather low contamination of the sampled environment with OCPs (median concentrations of sum DDTs: 826 ng/g lipid, sum chlordanes: 1,016 ng/g lipid, sum HCHs: 273 ng/g lipid). Hexachlorobenzene (HCB) and octachlorostyrene (OCS) were also found at low median levels of 134 and 3.4 ng/g lipid, respectively. Concentrations of most analytes were significantly higher in eggs collected from deserted nests in comparison to addled (unhatched) eggs, while eggshell thickness did not differ between deserted and addled eggs. No significant correlations were found between eggshell thickness and the analysed organohalogens. - PBDEs are measurable

  10. Hydrolysis of cupric chloride in aqueous ammoniacal ammonium chloride solutions

    Directory of Open Access Journals (Sweden)

    Limpo, J. L.

    1995-06-01

    Full Text Available Cupric solubility in the CuCl2-NH4Cl-NH3-H2O system for chloride concentrations lower than 4 molal in the temperature range 25-60 °C was studied. The experimental results show that for chloride concentration between 3.0 and 1.0 molal the cupric solubility is determined by the solubility of the cupric hydroxychloride Cu(OH1.5Cl0.5. For a chloride concentration value of 4.0 molal, there are two cupric compounds, the hydroxychloride Cu(OH1.5Cl0.5 or the diammine chloride Cu(NH32Cl2, on which the solubility of Cu(II depends, according to the temperature and the value of the ratio [NH3]Total/[Cu]Total.

    Se estudia la solubilidad del Cu(II en el sistema CuCl2-NH4Cl-NH3-H2O para concentraciones de cloruro inferiores a 4 molal en el intervalo de temperaturas 25-60 °C. Los resultados experimentales muestran que, para concentraciones de cloruros comprendidas entre 3,0 y 1,0 molal, la solubilidad cúprica viene determinada por la solubilidad del hidroxicloruro cúprico, Cu(OH1.5Cl0.5. Para concentraciones de cloruro 4,0 molal, existen dos compuestos cúpricos, el hidroxicloruro, Cu(OH1.5Cl0.5 o el cloruro de diamina, Cu(NH32Cl2, de los que, de acuerdo con la temperatura y con el valor de la relación [NH3]Total/[Cu]Total depende la solubilidad del Cu(II.

  11. Oxomemazine hydro­chloride

    Science.gov (United States)

    Siddegowda, M. S.; Butcher, Ray J.; Akkurt, Mehmet; Yathirajan, H. S.; Ramesh, A. R.

    2011-01-01

    In the title compound [systematic name: 3-(5,5-dioxo­phen­othia­zin-10-yl)-N,N,2-trimethyl­propanaminium chloride], C18H23N2O2S+·Cl−, the dihedral angle between the two outer aromatic rings of the phenothia­zine unit is 30.5 (2)°. In the crystal, the components are linked by N—H⋯Cl and C—H⋯Cl hydrogen bonds and C—H⋯π inter­actions. PMID:22090928

  12. Simple chloride sensors for continuous groundwater monitoring

    DEFF Research Database (Denmark)

    Thorn, Paul; Mortensen, John

    2012-01-01

    The development of chloride sensors which can be used for continuous, on-line monitoring of groundwater could be very valuable in the management of our coastal water resources. However, sensor stability, drift, and durability all need to be addressed in order for the sensors to be used...... in continuous application. This study looks at the development of a simple, inexpensive chloride electrode, and evaluates its performance under continuous use, both in the laboratory and in a field test in a monitoring well. The results from the study showed a consistent response to changing chloride...... sensor remained responsive even at low chloride concentrations, where the conductivity electrode was no longer responding to changing chloride levels. With the results, it is believed that the simple chloride sensor could be used for continuous monitoring of groundwater quality....

  13. Chloride Ion Critical Content in Reinforced Concrete

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Chloride ion critical content was studied under soaking and cycle of dry and wet conditions,with three electrochemical nondestructive measuring techniques, i e, half-cell potential, A C impedance, and time potential. The experimental results show that chloride ion critical content is primarily determined by the water cement ratio, while for the same concrete mixture the chloride ion critical content in soaking conditions is larger than that in a cycle of dry and wet conditions.

  14. Chloride binding site of neurotransmitter sodium symporters

    DEFF Research Database (Denmark)

    Kantcheva, Adriana Krassimirova; Quick, Matthias; Shi, Lei

    2013-01-01

    Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs...... have a serine. The LeuT-E290S mutant displays chloride-dependent activity. We show that, in LeuT-E290S cocrystallized with bromide or chloride, the anion is coordinated by side chain hydroxyls from Tyr47, Ser290, and Thr254 and the side chain amide of Gln250. The bound anion and the nearby sodium ion...

  15. Chloride ingress in cement paste and mortar

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, O.M.; Hansen, P.F.; Coats, A.M.; Glasser, F.P.

    1999-09-01

    In this paper chloride ingress in cement paste and mortar is followed by electron probe microanalysis. The influence of several paste and exposure parameters on chloride ingress are examined (e.g., water-cement ratio, silica fume addition, exposure time, and temperature). The measurements are modelled on Fick's law modified by a term for chloride binding. Inclusion of chloride binding significantly improves the profile shape of the modelled ingress profiles. The presence of fine aggregate and formation of interfacial transition zones at paste-aggregate boundaries does not significantly affect diffusion rates.

  16. Green process to recover magnesium chloride from residue solution of potassium chloride production plant

    Institute of Scientific and Technical Information of China (English)

    Lin WANG; Yunliang HE; Yanfei WANG; Ying BAO; Jingkang WANG

    2008-01-01

    The green process to recover magnesium chlor-ide from the residue solution of a potassium chloride pro-duction plant, which comes from the leach solution of a potash mine in Laos, is designed and optimized. The res-idue solution contains magnesium chloride above 25 wt-%, potassium chloride and sodium chloride together below 5 wt-% and a few other ions such as Br-, SO2-4and Ca2+. The recovery process contains two steps: the previous impurity removal operation and the two-stage evapora-tion-cooling crystallization procedure to produce magnes-ium chloride. The crystallized impurity carnallite obtained from the first step is recycled to the potassium chloride plant to recover the potassium salt. The developed process is a zero discharge one and thus fulfills the requirements for green chemical industrial production. The produced magnesium chloride is up to industrial criteria.

  17. ENVIRONMENTAL EXPOSURE TO VINYL CHLORIDE

    Directory of Open Access Journals (Sweden)

    Henryka Langauer-Lewowicka

    2010-09-01

    Full Text Available Vinyl chloride (VC monomer is a wellknown carcinogenic and mutagenic substance causes liver damages, angiosarcoma of the liver, acro – osteolysis, sclerodermalike changes in workers chronically exposed to this gas. There are following VC emitors to the environment: VC production plants, polymerization facilities and planes where polyvinyl products are fabricated. Because of that, the general population is coming into VC contact through polluted air, food and water. VC concentration in all mentioned sites is very low, often not detectable. There was found any health risk for the general population. The VC air concentration in the vicinity to antropogenic emitors is always higher. Such a situation may causes undesirable health effect for residents living in the neighbourhood. Epidemiological studies are performed to detect the adverse VC effect in selected cohorts. Non of the study did not confirmed cases of angiosarcoma among residents living near a vinyl chloride sites. VC production is growing permanently, so VC emission will be higher. Because of that health monitoring of general population and especially of selected groups seems to be necessary in the future.

  18. Tropospheric Bromine Chemistry: Implications for Present and Pre-industrial Ozone and Mercury

    Science.gov (United States)

    Parella, J. P.; Jacob, D. J.; Liang, Q.; Zhang, Y.; Mickley, L. J.; Miller, B.; Evans, M. J.; Yang, X.; Pyle, J. A.; Theys, N.; VanRoozendael, M.

    2012-01-01

    We present a new model for the global tropospheric chemistry of inorganic bromine (Bry) coupled to oxidant-aerosol chemistry in the GEOS-Chem chemical transport model (CTM). Sources of tropospheric Bry include debromination of sea-salt aerosol, photolysis and oxidation of short-lived bromocarbons, and transport from the stratosphere. Comparison to a GOME-2 satellite climatology of tropospheric BrO columns shows that the model can reproduce the observed increase of BrO with latitude, the northern mid-latitudes maximum in winter, and the Arctic maximum in spring. This successful simulation is contingent on the HOBr + HBr reaction taking place in aqueous aerosols and ice clouds. Bromine chemistry in the model decreases tropospheric ozone mixing ratios by chemistry improves the ability of global models (GEOS-Chem and p-TOMCAT) to simulate observed 19th-century ozone and its seasonality. Bromine effects on tropospheric ozone are comparable in the present-day and pre-industrial atmospheres so that estimates of anthropogenic radiative forcing are minimally affected. Br atom concentrations are 40% higher in the pre-industrial atmosphere due to lower ozone, which would decrease by a factor of 2 the atmospheric lifetime of elemental mercury against oxidation by Br. This suggests that historical anthropogenic mercury emissions may have mostly deposited to northern mid-latitudes, enriching the corresponding surface reservoirs. The persistent rise in background surface ozone at northern mid-latitudes during the past decades could possibly contribute to the observations of elevated mercury in subsurface waters of the North Atlantic.

  19. Distribution of copper, silver and gold during thermal treatment with brominated flame retardants.

    Science.gov (United States)

    Oleszek, Sylwia; Grabda, Mariusz; Shibata, Etsuro; Nakamura, Takashi

    2013-09-01

    The growing consumption of electric and electronic equipment results in creating an increasing amount of electronic waste. The most economically and environmentally advantageous methods for the treatment and recycling of waste electric and electronic equipment (WEEE) are the thermal techniques such as direct combustion, co-combustion with plastic wastes, pyrolysis and gasification. Nowadays, this kind of waste is mainly thermally treated in incinerators (e.g. rotary kilns) to decompose the plastics present, and to concentrate metals in bottom ash. The concentrated metals (e.g. copper, precious metals) can be supplied as a secondary raw material to metal smelters, while the pyrolysis of plastics allows the recovery of fuel gases, volatilising agents and, eventually, energy. Indeed, WEEE, such as a printed circuit boards (PCBs) usually contains brominated flame retardants (BFRs). From these materials, hydrobromic acid (HBr) is formed as a product of their thermal decomposition. In the present work, the bromination was studied of copper, silver and gold by HBr, originating from BFRs, such as Tetrabromobisphenol A (TBBPA) and Tetrabromobisphenol A-Tetrabromobisophenol A diglycidyl ether (TTDE) polymer; possible volatilization of the bromides formed was monitored using a thermo-gravimetric analyzer (TGA) and a laboratory-scale furnace for treating samples of metals and BFRs under an inert atmosphere and at a wide range of temperatures. The results obtained indicate that up to about 50% of copper and silver can evolve from sample residues in the form of volatile CuBr and AgBr above 600 and 1000°C, respectively. The reactions occur in the molten resin phase simultaneously with the decomposition of the brominated resin. Gold is resistant to HBr and remains unchanged in the residue.

  20. Production of HBR from bromine and steam for off-peak electrolytic hydrogen generation

    Energy Technology Data Exchange (ETDEWEB)

    Schlief, R.E.; Hanrahan, R.J.; Stoy, M.A. [Univ. of Florida, Gainesville, FL (United States)] [and others

    1995-09-01

    Progress is reported on the development of a renewable energy source based solar-electrolytic system for production of hydrogen and oxygen. It employs water, bromine, solar energy and supplemental electrical power. The concept is being developed by Solar Reactor Technologies, Inc., (SRT), with the U.S. Department of Energy (DOE). An overview of the nature and objectives of this program is provided here, and technical progress made during the first (three-month) performance period of the Phase I work effort is reported. The SRT concept entails (1) absorption of concentrated solar radiation by bromine vapor Br{sub 2(g)} in a high-temperature reactor producing Br{sub (g)} atoms, (2) reaction of Br{sub (g)} with water yielding hydrogen bromide (HBr), and (3) electrolysis of stored hydrogen bromide for production of H{sub 2(g)} and recovery of Br{sub 2(I)}. Incorporation of solar radiation in the primary photochemical step (1) reduces by 50 - 70% the electrical power required to split water. The SRT concept is very attractive from an economic viewpoint as well. The reversible fuel cell, employed in the SRT electrolysis concept is capitalized via its use in load leveling by the utility. A 1 kW solar reactor was designed and constructed during the first three-month performance period by SRT personnel at the University of Florida, Gainesville. It was employed in taking survey data of the reaction between bromine and steam at temperatures between 900 and 1300 K. This reaction was run under purely thermal conditions, i.e. in the absence of solar photons. The experimental data are reported and interpreted employing concomitant thermodynamic calculations. The anticipated improvement is discussed briefly as well as the effect of a photochemical boost to the reaction. The amount of this enhancement will be studied in the next three month performance period.

  1. Ways of reducing the bromine numbers of benzene for nitration with the use of the piperylene additive

    Energy Technology Data Exchange (ETDEWEB)

    Kolyandr, L.Ya.; Litvinenko, A.M.; Mastyukov, V.A.; Potapchenko, A.A.; Savikkova, M.T.; Shoherbakova, T.G.; Shuzhenko, E.A.; Titarenko, V.G.; Tkachenko, L.A.

    1981-01-01

    To study the diminution of the bromine numbers of benzene for nitration, an investigation has been made of the impurities according to the fractions of the tests of benzene production of three coke and chemical works: the works in Makeev-a, ka, Bagleisk and Yenakievo. It has been found that when the piperylene additive is used, the value of the bromine numbers of benzene for nitration is determined, in the main, not by the piperylenes removed during purification. When the intermediate BT fractions are not sufficiently clearly selected, the value of the bromine numbers of benzene is influenced also by the impurities which are concentrated in its terminal fractions. To radically remove piperylenes, it is necessary to improve the contact between the acid and the fraction being purified; this is attained by intensifying mixing and lengthening the purification process.

  2. Comparing polyaluminum chloride and ferric chloride for antimony removal.

    Science.gov (United States)

    Kang, Meea; Kamei, Tasuku; Magara, Yasumoto

    2003-10-01

    Antimony has been one of the contaminants required to be regulated, however, only limited information has been collected to date regarding antimony removal by polyaluminium chloride (PACl) and ferric chloride (FC). Accordingly, the possible use of coagulation by PACl or FC for antimony removal was investigated. Jar tests were used to determine the effects of solution pH, coagulant dosage, and pre-chlorination on the removal of various antimony species. Although high-efficiency antimony removal by aluminum coagulation has been expected because antimony is similar to arsenic in that both antimony and arsenic are a kind of metalloid in group V of the periodic chart, this study indicated: (1) removal density (arsenic or antimony removed per mg coagulant) for antimony by PACl was about one forty-fifth as low as observed for As(V); (2) although the removal of both Sb(III) and Sb(V) by coagulation with FC was much higher than that of PACl, a high coagulant dose of 10.5mg of FeL(-1) at optimal pH of 5.0 was still not sufficient to meet the standard antimony level of 2 microg as SbL(-1) for drinking water when around 6 microg as SbL(-1) were initially present. Consequently, investigation of a more appropriate treatment process is necessary to develop economical Sb reduction; (3) although previous studies concluded that As(V) is more effectively removed than As(III), this study showed that the removal of Sb(III) by coagulation with FC was much more pronounced than that of Sb(V); (4) oxidation of Sb(III) with chlorine decreased the ability of FC to remove antimony. Accordingly, natural water containing Sb(III) under anoxic condition should be coagulated without pre-oxidation.

  3. Electrochemical Behavior of Copper in Thionyl Chloride Solutions.

    Science.gov (United States)

    1980-12-01

    lithium - thionyl chloride batteries . Thionyl chloride is known *3 to react...electrolyte for lithium - thionyl chloride batteries . 8R. K. McAlpine and B. A. Soule, Prescott and Johnson’s Qualitative Chemical Analysis, D. Van...black carbon electrodes, cupric chloride appears to be a useful cathode additive for lithium - thionyl chloride batteries . Preliminary results2l

  4. Package of double helical bromine chains inside single-walled carbon nanotubes

    Science.gov (United States)

    Yao, Zhen; Liu, Chun Jian; Lv, Hang; Yang, Xi Bao

    2016-10-01

    The helicity of stable double helical bromine chains inside single-walled carbon nanotubes (SWCNTs) was studied through the calculation of systematic interaction energy, using the van der Waals interaction potential. The results presented clear images of stable double helical structures inside SWCNTs. The optimal helical radius and helical angle of chain structure increase and decrease, respectively, with the increase of tube radius. The detailed analysis indicated that some metastable structures in SWCNTs may also co-exist with the optimal structures, but not within the same tubes. In addition, a detailed simulation of X-ray diffraction patterns was performed for the obtained optimal helical structures.

  5. SYNTHESIS AND GREEN BROMINATION OF SOME CHALCONES AND THEIR ANTIMICROBIAL SCREENING

    Directory of Open Access Journals (Sweden)

    Mayur R. Adokar

    2013-04-01

    Full Text Available Chalcones are the versatile molecules having the structural flexibility which permits structural transformations into flavonoids, flavanones, pyrazoles, oxazoles, pyrimidines etc. Changes in their structure have offered the development of new medicinal agents having improved pharmacological potency. Their derivatives have attracts increasing attention due to numerous pharmacological potential. In the present communication we report the synthesis of chalcones from various acetophenone derivatives with different aromatic aldehydes and green chemistry approach to their bromination with the help of Tetrabutylammonium Tribromide (TBATB. All the synthesized chalcone dibromides were screened for their antimicrobial activity against Aspergillus flavus, Rhizopus sp., Fusarium solani and Aspergillus niger.

  6. Brominated flame retardants in waste electrical and electronic equipment: substance flows in a recycling plant.

    Science.gov (United States)

    Morf, Leo S; Tremp, Josef; Gloor, Rolf; Huber, Yvonne; Stengele, Markus; Zennegg, Markus

    2005-11-15

    Brominated flame retardants (BFRs) are synthetic additives mainly used in electrical and electronic appliances and in construction materials. The properties of some BFRs are typical for persistent organic pollutants, and certain BFRs, in particular some polybrominated diphenyl ether (PBDE) congeners and hexabromocyclododecane (HBCD), are suspected to cause adverse health effects. Global consumption of the most demanded BFRs, i.e., penta-, octa-, and decaBDE, tetrabromobisphenol A (TBBPA), and HBCD, has doubled in the 1990s. Only limited and rather uncertain data are available regarding the occurrence of BFRs in consumer goods and waste fractions as well as regarding emissions during use and disposal. The knowledge of anthropogenic substance flows and stocks is essential for early recognition of environmental impacts and effective chemicals management. In this paper, actual levels of penta-, octa-, and decaBDE, TBBPA, and HBCD in waste electrical and electronic equipment (WEEE) as a major carrier of BFRs are presented. These BFRs have been determined in products of a modern Swiss recycling plant applying gas chromatography/electron capture detection and gas chromatography/mass spectrometry analysis. A substance flow analysis (SFA) technique has been used to characterize the flows of target substances in the recycling process from the bulk WEEE input into the output products. Average concentrations in small size WEEE, representing the relevant electric and electronic appliances in WEEE, sampled in 2003 amounted to 34 mg/kg for pentaBDE, 530 mg/kg for octaBDE, 510 mg/kg for decaBDE, 1420 mg/kg for TBBPA (as an additive), 17 mg/kg for HBCD, 5500 mg/kg for bromine, and 1700 mg/kg for antimony. In comparison to data that have been calculated by SFA for Switzerland from literature for the 1990s, these measured concentrations in small size WEEE were 7 times higher for pentaBDE, unexpectedly about 50% lower for decaBDE, and agreed fairly well for TBBPA (as an additive) and

  7. Theoretical performance of hydrogen-bromine rechargeable SPE fuel cell. [Solid Polymer Electrolyte

    Science.gov (United States)

    Savinell, R. F.; Fritts, S. D.

    1988-01-01

    A mathematical model was formulated to describe the performance of a hydrogen-bromine fuel cell. Porous electrode theory was applied to the carbon felt flow-by electrode and was coupled to theory describing the solid polymer electrolyte (SPE) system. Parametric studies using the numerical solution to this model were performed to determine the effect of kinetic, mass transfer, and design parameters on the performance of the fuel cell. The results indicate that the cell performance is most sensitive to the transport properties of the SPE membrane. The model was also shown to be a useful tool for scale-up studies.

  8. Antibacterial Activities of a New Brominated Diterpene from Borneon Laurencia spp

    Science.gov (United States)

    Vairappan, Charles Santhanaraju; Ishii, Takahiro; Lee, Tan Kai; Suzuki, Minoru; Zhaoqi, Zhan

    2010-01-01

    In our continuous interest to study the diversity of halogenated metabolites of Malaysian species of the red algal genus Laurencia, we examined the chemical composition of five populations of unrecorded Laurencia sp. A new brominated diterpene, 10-acetoxyangasiol (1), and four other known metabolites, aplysidiol (2), cupalaurenol (3), 1-methyl-2,3,5-tribromoindole (4), and chamigrane epoxide (5), were isolated and identified. Isolated metabolites exhibited potent antibacterial activities against clinical bacteria, Staphylococcus aureus, Staphylococcus sp., Streptococcus pyogenes, Salmonella sp. and Vibrio cholerae. PMID:20631866

  9. Antibacterial Activities of a New Brominated Diterpene from Borneon Laurencia spp.

    Directory of Open Access Journals (Sweden)

    Charles Santhanaraju Vairappan

    2010-05-01

    Full Text Available In our continuous interest to study the diversity of halogenated metabolites of Malaysian species of the red algal genus Laurencia, we examined the chemical composition of five populations of unrecorded Laurencia sp. A new brominated diterpene, 10-acetoxyangasiol (1, and four other known metabolites, aplysidiol (2, cupalaurenol (3, 1-methyl-2,3,5-tribromoindole (4, and chamigrane epoxide (5, were isolated and identified. Isolated metabolites exhibited potent antibacterial activities against clinical bacteria, Staphylococcus aureus, Staphylococcus sp., Streptococcus pyogenes, Salmonella sp. and Vibrio cholerae.

  10. Characterization of Some Real Mixed Plastics from WEEE: A Focus on Chlorine and Bromine Determination by Different Analytical Methods

    Directory of Open Access Journals (Sweden)

    Beatrice Beccagutti

    2016-10-01

    Full Text Available Bromine and chlorine are almost ubiquitous in waste of electrical and electronic equipment (WEEE and the knowledge of their content in the plastic fraction is an essential step for proper end of life management. The aim of this study is to compare the following analytical methods: energy dispersive X-ray fluorescence spectroscopy (ED-XRF, ion chromatography (IC, ion-selective electrodes (ISEs, and elemental analysis for the quantitative determination of chlorine and bromine in four real samples taken from different WEEE treatment plants, identifying the best analytical technique for waste management workers. Home-made plastic standard materials with known concentrations of chlorine or bromine have been used for calibration of ED-XRF and to test the techniques before the sample analysis. Results showed that IC and ISEs, based upon dissolution of the products of the sample combustion, have not always achieved a quantitative absorption of the analytes in the basic solutions and that bromine could be underestimated since several oxidation states occur after combustion. Elemental analysis designed for chlorine determination is subjected to strong interference from bromine and required frequent regeneration and recalibration of the measurement cell. The most reliable method seemed to be the non-destructive ED-XRF. Calibration with home-made standards, having a similar plastic matrix of the samples, enabled us to carry out quantitative determinations, which have been revealed to be satisfactorily accurate and precise. In all the analyzed samples a total concentration of chlorine and/or bromine between 0.6 and 4 w/w% was detected, compromising the feasibility of a mechanical recycling and suggesting the exploration of an alternative route for managing these plastic wastes.

  11. Chronopotentiometric chloride sensing using transition time measurement

    NARCIS (Netherlands)

    Abbas, Y.; Graaf, de D.B.; Olthuis, W.; Berg, van den A.

    2013-01-01

    Detection of chloride ions is crucial to accurately access the concrete structure durability[1]. The existing electrochemical method of chloride ions detection in concrete, potentiometry[1], is not suitable for in-situ measurement due to the long term stability issue of conventional reference electr

  12. 29 CFR 1915.1017 - Vinyl chloride.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Vinyl chloride. 1915.1017 Section 1915.1017 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... § 1915.1017 Vinyl chloride. Note: The requirements applicable to shipyard employment under this...

  13. 29 CFR 1926.1117 - Vinyl chloride.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Vinyl chloride. 1926.1117 Section 1926.1117 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Toxic and Hazardous Substances § 1926.1117 Vinyl chloride. Note: The requirements applicable to construction work under this section are identical to...

  14. Chemische contaminanten in diervoeder additief Choline Chloride

    NARCIS (Netherlands)

    Traag, W.A.; Hoogenboom, L.A.P.; Jong, de J.; Egmond, van H.J.; Dam, ten G.

    2010-01-01

    Dit briefrapport beschrijft de resultaten van een onderzoek naar chemische contaminanten in Choline Chloride. De doelstellingen waren: 1) Inzicht te verkrijgen in het voorkomen van (gebromeerde) vlamvertragers en broomdioxines in het diervoederadditief Choline Chloride en het, op basis van de result

  15. Chloride ingress in cement paste and mortar

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede; Hansen, Per Freiesleben; Coats, Alison M.

    1999-01-01

    In this paper chloride ingress in cement paste and mortar is followed by electron probe microanalysis. The influence of several paste and exposure parameters on chloride ingress are examined (e.g., water-cement ratio, silica fume addition, exposure time, and temperature), The measurements...

  16. Electrospun Nafion®/Polyphenylsulfone Composite Membranes for Regenerative Hydrogen Bromine Fuel Cells

    Directory of Open Access Journals (Sweden)

    Jun Woo Park

    2016-02-01

    Full Text Available The regenerative H2/Br2-HBr fuel cell, utilizing an oxidant solution of Br2 in aqueous HBr, shows a number of benefits for grid-scale electricity storage. The membrane-electrode assembly, a key component of a fuel cell, contains a proton-conducting membrane, typically based on the perfluorosulfonic acid (PFSA ionomer. Unfortunately, the high cost of PFSA membranes and their relatively high bromine crossover are serious drawbacks. Nanofiber composite membranes can overcome these limitations. In this work, composite membranes were prepared from electrospun dual-fiber mats containing Nafion® PFSA ionomer for facile proton transport and an uncharged polymer, polyphenylsulfone (PPSU, for mechanical reinforcement, and swelling control. After electrospinning, Nafion/PPSU mats were converted into composite membranes by softening the PPSU fibers, through exposure to chloroform vapor, thus filling the voids between ionomer nanofibers. It was demonstrated that the relative membrane selectivity, referenced to Nafion® 115, increased with increasing PPSU content, e.g., a selectivity of 11 at 25 vol% of Nafion fibers. H2-Br2 fuel cell power output with a 65 μm thick membrane containing 55 vol% Nafion fibers was somewhat better than that of a 150 μm Nafion® 115 reference, but its cost advantage due to a four-fold decrease in PFSA content and a lower bromine species crossover make it an attractive candidate for use in H2/Br2-HBr systems.

  17. Development of Zinc/Bromine Batteries for Load-Leveling Applications: Phase 2 Final Report

    Energy Technology Data Exchange (ETDEWEB)

    CLARK,NANCY H.; EIDLER,PHILLIP

    1999-10-01

    This report documents Phase 2 of a project to design, develop, and test a zinc/bromine battery technology for use in utility energy storage applications. The project was co-funded by the U.S. Department of Energy Office of Power Technologies through Sandia National Laboratories. The viability of the zinc/bromine technology was demonstrated in Phase 1. In Phase 2, the technology developed during Phase 1 was scaled up to a size appropriate for the application. Batteries were increased in size from 8-cell, 1170-cm{sup 2} cell stacks (Phase 1) to 8- and then 60-cell, 2500-cm{sup 2} cell stacks in this phase. The 2500-cm{sup 2} series battery stacks were developed as the building block for large utility battery systems. Core technology research on electrolyte and separator materials and on manufacturing techniques, which began in Phase 1, continued to be investigated during Phase 2. Finally, the end product of this project was a 100-kWh prototype battery system to be installed and tested at an electric utility.

  18. Biodegradation kinetics of selected brominated flame retardants in aerobic and anaerobic soil

    Energy Technology Data Exchange (ETDEWEB)

    Nyholm, Jenny Rattfelt, E-mail: jenny.rattfelt@chem.umu.s [Department of Chemistry, Umea University, SE-901 87 Umea (Sweden); Lundberg, Charlott; Andersson, Patrik L. [Department of Chemistry, Umea University, SE-901 87 Umea (Sweden)

    2010-06-15

    The purpose of the present study was to investigate the biodegradation kinetics in aerobic and anaerobic soil of the following brominated flame retardants: 2,4,4'-tribromodiphenyl ether (BDE 28), decabromodiphenyl ether (BDE 209), tetrabromobisphenol A (TBBPA), 1,2-dibromo-4-(1,2-dibromoethyl)cyclohexane (TBECH), 2,4,6-tribromophenol (246BrPh), and hexabromobenzene (HxBrBz). For comparison, the biodegradation of the chlorinated compounds 2,4,4'-trichlorodiphenyl ether (CDE 28), 2,4,6-trichlorophenol (246ClPh), hexachlorobenzene (HxClBz), and 2,2',4,4',5,5'-hexachlorobiphenyl (PCB 153) was also assessed. In aerobic soil, BDE 209 showed no significant degradation during the test period, but concentrations of the other BFRs declined, with half-lives decreasing in the following order: BDE 28 > TBBPA > TBECH > HxBrBz > 246BrPh. Declines in almost the same order were observed in anaerobic soil: BDE 28, BDE 209 > TBBPA > HxBrBz > TBECH >246BrPh. - Intra- and extrapolated half-lives in soil of tested brominated flame retardants ranged from 7 days for 2,4,6-tribromorophenol to >400 days for decabromodiphenyl ether.

  19. Hair as an indicator of endogenous tissue levels of brominated flame retardants in mammals.

    Science.gov (United States)

    D'Havé, Helga; Covaci, Adrian; Scheirs, Jan; Schepens, Paul; Verhagen, Ron; De Coen, Wim

    2005-08-15

    Few data are available on brominated flame retardants (BFRs) in terrestrial mammalian wildlife. Moreover, the use of hair in nondestructive monitoring of BFRs in mammals or humans has not been investigated. In the present study, concentrations of polybrominated diphenyl ethers (PBDEs) and brominated biphenyl 153 (BB 153) were analyzed in tissues of the European hedgehog Erinaceus europaeus. Road kills and carcasses from wildlife rescue centers were used to investigate relationships between concentrations of BFRs in hair and internal tissues, BFR tissue distribution (hair, liver, kidney, muscle, and adipose tissue), and PBDE congener tissue pattern dissimilarities. Liver concentrations of PBDEs and BB 153 were in the ranges 1-1178 and 0-2.5 ng/g of liver wet weight, respectively. PBDEs were predominant in adipose tissue and liver, while accumulation of BB 153 was tissue independent. The less persistent compound BDE 99 was more dominant in hair than in internal tissues. We observed positive relationships between BFR levels in hair and internal tissues for sum PBDEs and BDE 47 (0.37 terrestrial mammals which can be used in nondestructive monitoring schemes.

  20. Synthesis of α-Bromine- Terminated Polystyrene Macroinitiator and Its Initiation of MMA Polymerization by ATRP

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In the present paper the synthesis of block copolymers via the transformation from living anionic polymerization (LAP) to atom transfer radical polymerization (ATRP) was described. Α-Bromine-terminated polystyrenes(PStBr) in the LAP step was prepared by using n-BuLi as initiator, tetrahydrofuran (THF) as the activator, α-methylstyrene (α-MeSt) as the capping group and liquid bromine (Br2) as the bromating agent. The effects of reaction conditions such as the amounts of α-MeSt, THF, and Br2 as well as molecular weight of polystyrene on the bromating efficiency (BE) and coupling extent (CE) were examined. The present results show that the yield of PStBr obtained was more than 93.8% and the coupling reaction was substantially absent. PStBr was further used as the macroinitiator in the polymerization of methyl-methacrylate(MMA) in the presence of copper(Ⅰ) halogen and 2,2-bipyridine(bpy) complexes. It was found that the molecular weight of the resulted PSt-b-PMMA increased linearly with the increase of the conversion of MMA and the polydispersity was 1.2-1.6. The structures of PStBr and P(St-b-MMA) were characterized by 1H NMR spectra.

  1. Novel Spectrophotometric Method for Determination of Macro-paracetamol via Reaction with Bromine

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The reaction between Br2 and paracetamol(p-AAP) leads to the formation of a coloured product, which can be used for spectrophotometric determination of the p-AAP content in its pure form and in different pharmaceutical preparations with p-AAP. The stoichiometric composition of the reaction was found to be n(p-AAP)∶n(bromine)=1∶3. The effects of pH and time on the spectra of p-AAP-bromine redox reaction product were studied. The interference of different additives on the measured spectra of the obtained product was also studied. The results obtained by the present method were compared with those obtained by the standard method. The F- and t- test values were calculated for both of the applied procedures and they met a confidence level of 99%. The proposed procedure actually needs no separation of these drugs from their sources before analysis and was unaffected by interference of other phenolic compounds. The proposed method is simpler and faster than the repoeted ones.

  2. Brominated diphenyl ethers in the sediments, porewater, and biota of the Chesapeake Bay, USA

    Energy Technology Data Exchange (ETDEWEB)

    Baker, K.; Klosterhaus, S.; Liebert, D.; Stapleton, H. [Maryland Univ., Solomons, MD (United States)

    2004-09-15

    Levels of brominated diphenyl ethers (BDEs) are rapidly increasing in the environment, and in a short time these chemicals have evolved from 'emerging contaminants' to globally-distributed organic pollutants. Recent research demonstrates BDEs are sufficiently stable to be transported long distances in the environment and to accumulate in higher trophic levels. Photolysis and metabolism appear to be dominant loss processes for the parent compounds, generating a variety of lower brominated diphenyl ethers, hydroxylated metabolites, and other products. BDEs are hydrophobic, and therefore their transport in aquatic systems is likely controlled by sorption to sediments and perhaps exchange across the air-water interface. To date, few studies have examined the geochemistry of BDEs in natural waters. In this paper, we review our recent measurements of BDEs in the Chesapeake Bay, a shallow, productive estuary in eastern North America. We focus on the distribution of BDE congeners sediment, porewater, and in faunal benthos along a contamination gradient downstream from a wastewater treatment plant and on the spatial distribution of BDEs in bottom-feeding and pelagic fish species.

  3. Dissolution of brominated epoxy resins by dimethyl sulfoxide to separate waste printed circuit boards.

    Science.gov (United States)

    Zhu, Ping; Chen, Yan; Wang, Liangyou; Qian, Guangren; Zhang, Wei Jie; Zhou, Ming; Zhou, Jin

    2013-03-19

    Improved methods are required for the recycling of waste printed circuit boards (WPCBs). In this study, WPCBs (1-1.5 cm(2)) were separated into their components using dimethyl sulfoxide (DMSO) at 60 °C for 45 min and a metallographic microscope was used to verify their delamination. An increased incubation time of 210 min yielded a complete separation of WPCBs into their components, and copper foils and glass fibers were obtained. The separation time decreased with increasing temperature. When the WPCB size was increased to 2-3 cm(2), the temperature required for complete separation increased to 90 °C. When the temperature was increased to 135 °C, liquid photo solder resists could be removed from the copper foil surfaces. The DMSO was regenerated by rotary decompression evaporation, and residues were obtained. Fourier transform infrared spectroscopy (FT-IR), thermal analysis, nuclear magnetic resonance, scanning electron microscopy, and energy-dispersive X-ray spectroscopy were used to verify that these residues were brominated epoxy resins. From FT-IR analysis after the dissolution of brominated epoxy resins in DMSO it was deduced that hydrogen bonding may play an important role in the dissolution mechanism. This novel technology offers a method for separating valuable materials and preventing environmental pollution from WPCBs.

  4. Natural solar photolysis of total organic chlorine, bromine and iodine in water.

    Science.gov (United States)

    Abusallout, Ibrahim; Hua, Guanghui

    2016-04-01

    Municipal wastewater has been increasingly used to augment drinking water supplies due to the growing water scarcity. Wastewater-derived disinfection byproducts (DBPs) may negatively affect the aquatic ecosystems and human health of downstream communities during water reuse. The objective of this research was to determine the degradation kinetics of total organic chlorine (TOCl), bromine (TOBr) and iodine (TOI) in water by natural sunlight irradiation. Outdoor solar photolysis experiments were performed to investigate photolytic degradation of the total organic halogen (TOX) formed by fulvic acid and real water and wastewater samples. The results showed that TOX degradation by sunlight irradiation followed the first-order kinetics with half-lives in the range of 2.6-10.7 h for different TOX compounds produced by fulvic acid. The TOX degradation rates were generally in the order of TOI > TOBr ≅ TOCl(NH2Cl) > TOCl(Cl2). High molecular weight TOX was more susceptible to solar photolysis than corresponding low molecular weight halogenated compounds. The nitrate and sulfite induced indirect TOX photolysis rates were less than 50% of the direct photolysis rates under the conditions of this study. Fulvic acid and turbidity in water reduced TOX photodegradation. These results contribute to a better understanding of the fate of chlorinated, brominated and iodinated DBPs in surface waters.

  5. Chloride Transport in Undersea Concrete Tunnel

    Directory of Open Access Journals (Sweden)

    Yuanzhu Zhang

    2016-01-01

    Full Text Available Based on water penetration in unsaturated concrete of underwater tunnel, a diffusion-advection theoretical model of chloride in undersea concrete tunnel was proposed. The basic parameters including porosity, saturated hydraulic conductivity, chloride diffusion coefficient, initial water saturation, and moisture retention function of concrete specimens with two water-binder ratios were determined through lab-scale experiments. The variation of chloride concentration with pressuring time, location, solution concentration, initial saturation, hydraulic pressure, and water-binder ratio was investigated through chloride transport tests under external water pressure. In addition, the change and distribution of chloride concentration of isothermal horizontal flow were numerically analyzed using TOUGH2 software. The results show that chloride transport in unsaturated concrete under external water pressure is a combined effect of diffusion and advection instead of diffusion. Chloride concentration increased with increasing solution concentration for diffusion and increased with an increase in water pressure and a decrease in initial saturation for advection. The dominant driving force converted with time and saturation. When predicting the service life of undersea concrete tunnel, it is suggested that advection is taken into consideration; otherwise the durability tends to be unsafe.

  6. Subacute effects of the brominated flame retardants hexabromocyclododecane and tetrabromobisphenol A on hepatic cytochrome P450 levels in rats.

    NARCIS (Netherlands)

    Germer, Silke; Piersma, Aldert H; Ven, Leo T M van der; Kamyschnikow, Andreas; Fery, Yvonne; Schmitz, Hans-Joachim; Schrenk, Dieter

    2006-01-01

    The brominated flame retardants tetrabromobisphenol A (TBBPA) and hexabromocyclododecane (HBCD) are found in the environment, e.g., in sediments and organisms, in food items, human blood samples and mother's milk. In this study, the effects of both compounds on rat hepatic cytochrome P450 (CYP) leve

  7. Rapid Formation of Molecular Bromine from Deliquesced NaBr Aerosol in the Presence of Ozone and UV Light

    Science.gov (United States)

    The formation of gas-phase bromine from aqueous sodium bromide aerosols is investigated through a combination of chamber experiments and chemical kinetics modeling. Experiments show that Br2(g) is produced rapidly from deliquesced NaBr aerosols in the presence of OH radicals prod...

  8. Exposure to brominated trihalomethanes in water during pregnancy and micronuclei frequency in maternal and cord blood lymphocytes

    DEFF Research Database (Denmark)

    Stayner, Leslie Thomas; Pedersen, Marie; Patelarou, Evridiki;

    2014-01-01

    BACKGROUND: Water disinfection by-products have been associated with an increased cancer risk. Micronuclei (MN) frequency in lymphocytes is a marker of genomic damage and can predict adult cancer risk. OBJECTIVE: We evaluated maternal exposure to drinking water brominated trihalomethanes (BTHM) i...

  9. Prenatal Exposure to Organohalogens, Including Brominated Flame Retardants, Influences Motor, Cognitive, and Behavioral Performance at School Age

    NARCIS (Netherlands)

    Roze, Elise; Meijer, Lisethe; Bakker, Attie; Van Braeckel, Koenraad N. J. A.; Sauer, Pieter J. J.; Bos, Arend F.

    2009-01-01

    BACKGROUND: Organohalogen compounds (OHCs) are known to have neurotoxic effects on the developing brain. OBJECTIVE: We investigated the influence of prenatal exposure to OHCs, including brominated flame retardants, on motor, cognitive, and behavioral outcome in healthy children of school age. METHOD

  10. Suppressing effect of calcium-based waste on control of bromine flux during the pyrolysis of printed circuit boards.

    Science.gov (United States)

    Jie, Guan; Min, Xu; Wu, Wenjie; Zhang, Chenglong; Wang, Jingwei; Bai, Jianfeng

    2012-11-01

    The effect of calcium-based addition on the brominate flux during printed circuit board (PCB) pyrolysis was investigated. It was found that bromine (Br) can be effectively fixed in solid phase during PCB pyrolysis by adding calcium-based waste materials. Phenol and 4-ethylphenol are the major products of pyrolysis. When the two kinds of red mud were used as additive, their content was 85.25 and 84.81%, respectively, which was higher than others. The 2-bromophenol and 2-bromo-4-methyl-benzene are the main Br-containing pyrolysis volatiles. After adding calcium-based additive, these two volatiles were apparently reduced and only small amounts of 2-bromo-4-methyl-benzene were detected in the products, namely 0.71 and 0.86%, respectively for the two kinds of red mud. Hence, no matter from the perspective of product use or simple Br-fixing, the bromine in the three-phase products can be effectively regulated and controlled by adding calcium-based waste residue during PCB pyrolysis. Finally, the Br-fixing mechanism was analysed. As a result, when calcium-based waste materials were added to the PCB pyrolysis it made bromine fix easily in the resident yielding a byproduct that can be further used.

  11. Temporal development of brominated flame retardants in peregrine falcon (Fako peregrinus) eggs from South Greenland (1986-2003)

    NARCIS (Netherlands)

    Vorkamp, K.; Thomsen, M.; Falk, K.; Leslie, H.A.; Moller, S.; Sorensen, P.B.

    2005-01-01

    A time trend between 1986 and 2003 was found for brominated flame retardants in peregrine falcon eggs from South Greenland, with significantly increasing concentrations of the polybrominated diphenyl ethers (PBDEs) 99, 100, 153, 154, and 209. For BDE-99 and -100, the concentration increased approxim

  12. The detection of some halogenated phenols and nitrophenols in thin-layer chromatography by means of bromine

    NARCIS (Netherlands)

    Tadema, G.; Batelaan, P.H.

    1968-01-01

    A method is described for the detection of halogeno- and nitro-phenols in sub-microgram quantities. Theses compounds are made visible by exposure of the developed thin layer plates to bromine vapour and subsequent spraying with an aqueous solution of potassium iodide or an ethanolic solution of fluo

  13. Corrosion mechanism of 13Cr stainless steel in completion fluid of high temperature and high concentration bromine salt

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yan [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Xu, Lining, E-mail: xulining@ustb.edu.cn [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Lu, Minxu [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Meng, Yao [Beijing Institute of Aeronautical Materials, Beijing 100095 (China); Zhu, Jinyang; Zhang, Lei [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China)

    2014-09-30

    Highlights: • The corrosion behavior of 13Cr steel exposed to bromine salt completion fluid containing high concentration bromine ions was investigated. • There are passive circles around pits on the 13Cr steel surface after 7 d of exposure. • Macroscopic galvanic corrosion formed between the passive halo and the pit. • The mechanism of pitting corrosion on 13Cr stainless steel exposed to heavy bromine brine was established. - Abstract: A series of corrosion tests of 13Cr stainless steel were conducted in a simulated completion fluid environment of high temperature and high concentration bromine salt. Corrosion behavior of specimens and the component of corrosion products were investigated by means of scanning electron microscope (SEM), confocal laser scanning microscopy (CLSM) and X-ray photoelectron spectroscopy (XPS). The results indicate that 13Cr steel suffers from severe local corrosion and there is always a passive halo around every pit. The formation mechanism of the passive halo is established. OH{sup −} ligand generates and adsorbs in a certain scale because of abundant OH{sup −} on the surface around the pits. Passive film forms around each pit, which leads to the occurrence of passivation in a certain region. Finally, the dissimilarities in properties and morphologies of regions, namely the pit and its corresponding passive halo, can result in different corrosion sensitivities and may promote the formation of macroscopic galvanic pairs.

  14. Reaction of bromine and chlorine with phenolic compounds and natural organic matter extracts--Electrophilic aromatic substitution and oxidation.

    Science.gov (United States)

    Criquet, Justine; Rodriguez, Eva M; Allard, Sebastien; Wellauer, Sven; Salhi, Elisabeth; Joll, Cynthia A; von Gunten, Urs

    2015-11-15

    Phenolic compounds are known structural moieties of natural organic matter (NOM), and their reactivity is a key parameter for understanding the reactivity of NOM and the disinfection by-product formation during oxidative water treatment. In this study, species-specific and/or apparent second order rate constants and mechanisms for the reactions of bromine and chlorine have been determined for various phenolic compounds (phenol, resorcinol, catechol, hydroquinone, phloroglucinol, bisphenol A, p-hydroxybenzoic acid, gallic acid, hesperetin and tannic acid) and flavone. The reactivity of bromine with phenolic compounds is very high, with apparent second order rate constants at pH 7 in the range of 10(4) to 10(7) M(-1) s(-1). The highest value was recorded for the reaction between HOBr and the fully deprotonated resorcinol (k = 2.1 × 10(9) M(-1) s(-1)). The reactivity of phenolic compounds is enhanced by the activating character of the phenolic substituents, e.g. further hydroxyl groups. With the data set from this study, the ratio between the species-specific rate constants for the reactions of chlorine versus bromine with phenolic compounds was confirmed to be about 3000. Phenolic compounds react with bromine or chlorine either by oxidation (electron transfer, ET) or electrophilic aromatic substitution (EAS) processes. The dominant process mainly depends on the relative position of the hydroxyl substituents and the possibility of quinone formation. While phenol, p-hydroxybenzoic acid and bisphenol A undergo EAS, hydroquinone, catechol, gallic acid and tannic acid, with hydroxyl substituents in ortho or para positions, react with bromine by ET leading to quantitative formation of the corresponding quinones. Some compounds (e.g. phloroglucinol) show both partial oxidation and partial electrophilic aromatic substitution and the ratio observed for the pathways depends on the pH. For the reaction of six NOM extracts with bromine, electrophilic aromatic substitution

  15. Chloride Ingress into Concrete under Water Pressure

    OpenAIRE

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent; Hansen, Kurt Kielsgaard

    2011-01-01

    The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 kPa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly infl...

  16. Reliability-Based Planning of Chloride Measurements

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Engelund, S.

    1996-01-01

    on measurements of the chloride content obtained from the given structure. In the present paper optimal planning of measurements of the chloride content in reinforced concrete structures is considered. It is shown how optimal experimental plans can be obtained using FORM-analysis. Bayesian statistics are used......In reinforced concrete structures corrosion is initiated when the chloride concentration around the reinforcement exceeds a threshold value. If corrosion starts then expensive repairs can be necessary. The estimation of the probability that corrosion has been initiated in a given structure is based...

  17. Assessing the persistence, bioaccumulation potential and toxicity of brominated flame retardants: data availability and quality for 36 alternative brominated flame retardants.

    Science.gov (United States)

    Stieger, Greta; Scheringer, Martin; Ng, Carla A; Hungerbühler, Konrad

    2014-12-01

    Polybrominated diphenylethers (PBDEs) and hexabromocyclododecane (HBCDD) are major brominated flame retardants (BFRs) that are now banned or under restrictions in many countries because of their persistence, bioaccumulation potential and toxicity (PBT properties). However, there is a wide range of alternative BFRs, such as decabromodiphenyl ethane and tribromophenol, that are increasingly used as replacements, but which may possess similar hazardous properties. This necessitates hazard and risk assessments of these compounds. For a set of 36 alternative BFRs, we searched 25 databases for chemical property data that are needed as input for a PBT assessment. These properties are degradation half-life, bioconcentration factor (BCF), octanol-water partition coefficient (Kow), and toxic effect concentrations in aquatic organisms. For 17 of the 36 substances, no data at all were found for these properties. Too few persistence data were available to even assess the quality of these data in a systematic way. The available data for Kow and toxicity show surprisingly high variability, which makes it difficult to identify the most reliable values. We propose methods for systematic evaluations of PBT-related chemical property data that should be performed before data are included in publicly available databases. Using these methods, we evaluated the data for Kow and toxicity in more detail and identified several inaccurate values. For most of the 36 alternative BFRs, the amount and the quality of the PBT-related property data need to be improved before reliable hazard and risk assessments of these substances can be performed.

  18. Bromine release during Plinian eruptions along the Central American Volcanic Arc

    Science.gov (United States)

    Hansteen, T. H.; Kutterolf, S.; Appel, K.; Freundt, A.; Perez-Fernandez, W.; Wehrmann, H.

    2010-12-01

    Volcanoes of the Central American Volcanic Arc (CAVA) have produced at least 72 highly explosive eruptions within the last 200 ka. The eruption columns of all these “Plinian” eruptions reached well into the stratosphere such that their released volatiles may have influenced atmospheric chemistry and climate. While previous research has focussed on the sulfur and chlorine emissions during such large eruptions, we here present measurements of the heavy halogen bromine by means of synchrotron radiation induced micro-XRF microanalysis (SR-XRF) with typical detection limits at 0.3 ppm (in Fe rich standard basalt ML3B glass). Spot analyses of pre-eruptive glass inclusions trapped in minerals formed in magma reservoirs were compared with those in matrix glasses of the tephras, which represent the post-eruptive, degassed concentrations. The concentration difference between inclusions and matrix glasses, multiplied by erupted magma mass determined by extensive field mapping, yields estimates of the degassed mass of bromine. Br is probably hundreds of times more effective in destroying ozone than Cl, and can accumulate in the stratosphere over significant time scales. Melt inclusions representing deposits of 22 large eruptions along the CAVA have Br contents between 0.5 and 13 ppm. Br concentrations in matrix glasses are nearly constant at 0.4 to 1.5 ppm. However, Br concentrations and Cl/Br ratios vary along the CAVA. The highest values of Br contents (>8 ppm) and lowest Cl/Br ratios (170 to 600) in melt inclusions occur across central Nicaragua and southern El Salvador, and correlate with bulk-rock compositions of high Ba/La > 85 as well as low La/Yb discharged 700 kilotons of Br. On average, each of the remaining 21 CAVA eruptions studied have discharged c.100 kilotons of bromine. During the past 200 ka, CAVA volcanoes have emitted a cumulative mass of 3.2 Mt of Br through highly explosive eruptions. There are six periods in the past (c. 2ka, 6ka, 25ka, 40ka, 60ka, 75

  19. Investigating the lifetime of bromine-quenched G.M. Counters with temperature

    Energy Technology Data Exchange (ETDEWEB)

    Abilama, Marc [Centronic Ltd., Croydon (United Kingdom); University of Surrey, Guildford (United Kingdom); Bates, Mike [Centronic Ltd., Croydon (United Kingdom); Lohstroh, Annika [University of Surrey, Guildford (United Kingdom)

    2015-09-21

    The amount of halogen quench gas as a percentage of the total fill gas contained within a gas-filled Geiger–Müller detector is directly linked to its operational characteristics. Preserving this halogen gas will help maintain the operating lifetime of the detectors. Such halogen gases are highly corrosive and the small quantities within a gas-filled detector can deplete rapidly via interactions with surrounding materials. The rate of interactions is thought to be proportional to not only temperature, but also to the current initiated by ionisation events associated with the formation of each signal pulse. As all pulses are of similar magnitudes, GM detector operational lifetimes are quantified in accumulated counts rather than a given operating time. We have studied three different types of corrosion-resistant mechanisms to protect the bromine halogen gas from any interactions with 446 stainless steel detector components of ZP1200 Geiger–Müller tubes at temperatures up to 125 °C. Three types of surface treatments for these detectors used were labelled as “raw” using only an oxygen-plasma-bombardment process, “passivated” using a combination of nitric acid passivation followed by an oxygen plasma-bombardment process, and thirdly plating with a few micron thickness of chromium followed by an oxygen plasma-bombardment process. 32 detector samples were irradiated at room temperature with a Caesium-137 source at dose rates of approximately 1.3 mSv/hr up to 5.7×10{sup 10} accumulated counts; another 32 detector samples were aged to 3.3×10{sup 10} counts at 125 °C. At room temperature, the chromium-plated samples exhibited an initial rise in their starting voltage readings. All other detector performance characteristics, for all detector types, did not change significantly during the ageing process, and the surface morphology of the detector cathodes was unaffected. At 125 °C, the chromium-based plating produced the most stable long-term response. These

  20. Mercury oxidation from bromine chemistry in the free troposphere over the southeastern US

    Directory of Open Access Journals (Sweden)

    S. Coburn

    2015-10-01

    Full Text Available The elevated deposition of atmospheric mercury over the Southeastern United States is currently not well understood. Here we measure partial columns and vertical profiles of bromine monoxide (BrO radicals, a key component of mercury oxidation chemistry, to better understand the processes and altitudes at which mercury is being oxidized in the atmosphere. We use the data from a ground-based MAX-DOAS instrument located at a coastal site ~ 1 km from the Gulf of Mexico in Gulf Breeze, FL, where we had previously detected tropospheric BrO (Coburn et al., 2011. Our profile retrieval assimilates information about stratospheric BrO from the WACCM chemical transport model, and uses only measurements at moderately low solar zenith angles (SZA to estimate the BrO slant column density contained in the reference spectrum (SCDRef. The approach has 2.6 degrees of freedom, and avoids spectroscopic complications that arise at high SZA; knowledge about SCDRef helps to maximize sensitivity in the free troposphere (FT. A cloud-free case study day with low aerosol load (9 April 2010 provided optimal conditions for distinguishing marine boundary layer (MBL: 0–1 km and free tropospheric (FT: 1–15 km BrO from the ground. The average daytime tropospheric BrO vertical column density (VCD of ~ 2.3 × 1013 molec cm−2 (SZA 5 molec cm−2 s−1 for bromine, while contributions from ozone (O3 and chlorine (Cl were 0.9 × 105 and 0.2 × 105 molec cm−2 s−1, respectively. The GOM formation rate is sensitive to recently proposed atmospheric scavenging reactions of the HgBr adduct by nitrogen dioxide (NO2, and to a lesser extent also HO2 radicals. Using a 3-D chemical transport model, we find that surface GOM variations are typical also of other days, and are mainly derived from the free troposphere. Bromine chemistry is active in the FT over Gulf Breeze, where it forms water-soluble GOM that is subsequently available for wet scavenging by thunderstorms or transport to

  1. Seasonal variation of bromine monoxide over the Rann of Kutch salt marsh seen from space

    Science.gov (United States)

    Hörmann, Christoph; Beirle, Steffen; Penning de Vries, Marloes; Sihler, Holger; Platt, Ulrich; Wagner, Thomas

    2015-04-01

    Bromine monoxide (BrO) is an important catalyst in the depletion of tropospheric and stratospheric ozone (O3). In the troposphere, reactive bromine can be released from sea ice, volcanoes, sea-salt aerosol or salt lakes. For all of these natural sources enhanced BrO vertical column densities (VCDs) have been successfully observed from ground using Differential Optical Absorption Spectroscopy (DOAS). Until now, satellite observations were only reported for polar regions during springtime and volcanic emissions (mostly for major eruptions). We present the first satellite observations of enhanced monthly mean BrO VCDs over a salt marsh, the Rann of Kutch (India/Pakistan), during 2004-2014 as seen by the Ozone Monitoring Instrument (OMI). The Rann of Kutch is a so-called 'seasonal' salt marsh. During India's summer monsoon (June/July - September/October), the flat desert of salty clay and mudflats, which average 15 meters above sea level, fills with standing rain and sea water. With more than 7500 km2 it is the largest salt desert in the world and additionally one of the hottest areas of India with summer temperatures around 50 ° C and winter temperatures decreasing below 0 ° C. Probably due to these rather extreme conditions, the Rann of Kutch has not been yet investigated for atmospheric composition measurements by ground-based instruments. Satellite observations, however, provide the unique possibility to investigate the entire area remotely over a long-time period. The OMI data reveals recurring maximum BrO VCDs during April/May, but no enhanced column densities during the monsoon season while the area is flooded. In the following months the signal only recovers slowly while the salty surface dries up. We discuss the possible effects of temperature, precipitation and relative humidity on the release of enhanced reactive bromine concentrations. In order to investigate a possible diurnal cycle of the BrO concentration, the OMI results (at a local overflight time

  2. Determination of bromide, chloride, fluoride, nitrate and sulphate by ion chromatography: comparisons of methodologies for rainfall, cloud water and river waters at the Plynlimon catchments of mid-Wales

    Directory of Open Access Journals (Sweden)

    2007-01-01

    Full Text Available The results of determination of bromide, chloride, fluoride, nitrate and sulphate using ion chromatography (IC are compared with those obtained by colorimetric and inductively coupled plasma optical emission spectroscopy (ICPOES for rainfall, cloud water and stream waters in the Plynlimon experimental catchments of mid-Wales. For bromide, the concentrations determined by IC are lower than those for the colorimetric method used; the colorimetric method probably determined bromide plus organo-bromine compounds. It is suggested that the values determined by the colorimetric method be termed dissolved labile bromine (DLBr. The study shows that sulphate is the overriding form of sulphur in the waters. For chloride and nitrate, measurements by both methods approach a 1:1 relationship that is barely statistically significantly different from unity. For fluoride, the IC method gives lower values than the colorimetric, especially for the stream waters. However, the colorimetric method determines total fluorine so that a difference is to be expected (for example, fluoride strongly complexes with aluminium that is present, especially in the streamwater.

  3. Catastrophic event modeling. [lithium thionyl chloride batteries

    Science.gov (United States)

    Frank, H. A.

    1981-01-01

    A mathematical model for the catastrophic failures (venting or explosion of the cell) in lithium thionyl chloride batteries is presented. The phenomenology of the various processes leading to cell failure is reviewed.

  4. Surface adsorption in strontium chloride ammines

    DEFF Research Database (Denmark)

    Ammitzbøll, Andreas L.; Lysgaard, Steen; Klukowska, Agata

    2013-01-01

    An adsorbed state and its implications on the ab- and desorption kinetics of ammonia in strontium chloride ammine is identified using a combination of ammonia absorption measurements, thermogravimetric analysis, and density functional theory calculations. During thermogravimetric analysis, ammoni...

  5. Qualitative Determination of Nitrate with Triphenylbenzylphosphonium Chloride.

    Science.gov (United States)

    Berry, Donna A.; Cole, Jerry J.

    1984-01-01

    Discusses two procedures for the identification of nitrate, the standard test ("Brown Ring" test) and a new procedure using triphenylbenzylphosphonium chloride (TPBPC). Effectiveness of both procedures is compared, with the TPBPC test proving to be more sensitive and accurate. (JM)

  6. Corneal Neurotoxicity Due to Topical Benzalkonium Chloride

    OpenAIRE

    Sarkar, Joy; Chaudhary, Shweta; Namavari, Abed; Ozturk, Okan; Chang, Jin-Hong; Yco, Lisette; Sonawane, Snehal; Khanolkar, Vishakha; Hallak, Joelle; Jain, Sandeep

    2012-01-01

    Topical application of benzalkonium chloride (BAK) to the eye causes dose-related corneal neurotoxicity. Corneal inflammation and reduction in aqueous tear production accompany neurotoxicity. Cessation of BAK treatment leads to recovery of corneal nerve density.

  7. Chloride Ingress into Concrete under Water Pressure

    DEFF Research Database (Denmark)

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent;

    2011-01-01

    The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 k......Pa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly influences the chloride ingress into the concrete and thereby the life length models for concrete structures....

  8. 75 FR 20625 - Barium Chloride From China

    Science.gov (United States)

    2010-04-20

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Revised schedule for the subject review. DATES: Effective Date: April 9, 2010. FOR FURTHER INFORMATION CONTACT:...

  9. Telomerization of Vinyl Chloride with Chloroform Initiated by Ferrous Chloride-Dimethylacetamide under Ultrasonic Conditions

    Directory of Open Access Journals (Sweden)

    Hua Qian

    2015-01-01

    Full Text Available Telomerization of vinyl chloride with chloroform was investigated using ferrous chloride-dimethylacetamide system, and 42.1% yield, more than four times the one reported before, was achieved. The addition of ultrasound further improved the reaction and yield was raised to 51.9% with trace byproducts at highly reduced reaction time and temperature. Ferrous chloride-dimethylacetamide under ultrasonic irradiation acts as a very efficient catalyst system for the 1 : 1 telomerization.

  10. Air-snowpack exchange of bromine, ozone and mercury in the springtime Arctic simulated by the 1-D model PHANTAS – Part 1: In-snow bromine activation and its impact on ozone

    Directory of Open Access Journals (Sweden)

    K. Toyota

    2013-08-01

    Full Text Available To provide a theoretical framework towards better understanding of ozone depletion events (ODEs and atmospheric mercury depletion events (AMDEs in the polar boundary layer, we have developed a one-dimensional model that simulates multiphase chemistry and transport of trace constituents from porous snowpack and through the atmospheric boundary layer (ABL as a unified system. In this paper, we describe a general configuration of the model and the results of simulations related to reactive bromine release from the snowpack and ODEs during the Arctic spring. The model employs a chemical mechanism adapted from the one previously used for the simulation of multiphase halogen chemistry involving deliquesced sea-salt aerosols in the marine boundary layer. A common set of aqueous-phase reactions describe chemistry both in the liquid-like (or brine layer on the grain surface of the snowpack and in "haze" aerosols mainly composed of sulfate in the atmosphere. The process of highly soluble/reactive trace gases, whether entering the snowpack from the atmosphere or formed via gas-phase chemistry in the snowpack interstitial air (SIA, is simulated by the uptake on brine-covered snow grains and subsequent reactions in the aqueous phase while being traveled vertically within the SIA. A "bromine explosion", by which, in a conventional definition, HOBr formed in the ambient air is deposited and then converted heterogeneously to Br2, is a dominant process of reactive bromine formation in the top 1 mm (or less layer of the snowpack. Deeper in the snowpack, HOBr formed within the SIA leads to an in-snow bromine explosion, but a significant fraction of Br2 is also produced via aqueous radical chemistry in the brine on the surface of the snow grains. These top- and deeper-layer productions of Br2 both contribute to the Br2 release into the atmosphere, but the deeper-layer production is found to be more important for the net outflux of reactive bromine. Although ozone

  11. Air-snowpack exchange of bromine, ozone and mercury in the springtime Arctic simulated by the 1-D model PHANTAS - Part 1: In-snow bromine activation and its impact on ozone

    Science.gov (United States)

    Toyota, K.; McConnell, J. C.; Staebler, R. M.; Dastoor, A. P.

    2014-04-01

    To provide a theoretical framework towards a better understanding of ozone depletion events (ODEs) and atmospheric mercury depletion events (AMDEs) in the polar boundary layer, we have developed a one-dimensional model that simulates multiphase chemistry and transport of trace constituents from porous snowpack and through the atmospheric boundary layer (ABL) as a unified system. This paper constitutes Part 1 of the study, describing a general configuration of the model and the results of simulations related to reactive bromine release from the snowpack and ODEs during the Arctic spring. A common set of aqueous-phase reactions describes chemistry both within the liquid-like layer (LLL) on the grain surface of the snowpack and within deliquesced "haze" aerosols mainly composed of sulfate in the atmosphere. Gas-phase reactions are also represented by the same mechanism in the atmosphere and in the snowpack interstitial air (SIA). Consequently, the model attains the capacity of simulating interactions between chemistry and mass transfer that become particularly intricate near the interface between the atmosphere and the snowpack. In the SIA, reactive uptake on LLL-coated snow grains and vertical mass transfer act simultaneously on gaseous HOBr, a fraction of which enters from the atmosphere while another fraction is formed via gas-phase chemistry in the SIA itself. A "bromine explosion", by which HOBr formed in the ambient air is deposited and then converted heterogeneously to Br2, is found to be a dominant process of reactive bromine formation in the top 1 mm layer of the snowpack. Deeper in the snowpack, HOBr formed within the SIA leads to an in-snow bromine explosion, but a significant fraction of Br2 is also produced via aqueous radical chemistry in the LLL on the surface of the snow grains. These top- and deeper-layer productions of Br2 both contribute to the release of Br2 to the atmosphere, but the deeper-layer production is found to be more important for the

  12. Cesium chloride-induced torsades de pointes

    OpenAIRE

    Wiens, Matthew; Gordon, Wendy; Baulcomb, Daisy; Mattman, Andre; Mock, Tom; Brown, Robert

    2009-01-01

    The chloride salt of cesium, a group 1A element, is gaining popularity as an alternative treatment of advanced cancers. Cesium chloride has primarily been used in cardiovascular research for arrhythmogenesis in animals because of its potassium-blocking effects. The present report describes a 45-year-old woman with metastatic breast cancer who experienced repeated episodes of torsades de pointes polymorphic ventricular tachycardia after several months of oral cesium therapy. There was a clear ...

  13. The kinetics of the hydrogen chloride oxidation

    Directory of Open Access Journals (Sweden)

    Gonzalez Martinez Isai

    2013-01-01

    Full Text Available Hydrogen chloride (HCl oxidation has been investigated on technical membrane electrode assemblies in a cyclone flow cell. Influence of Nafion loading, temperature and hydrogen chloride mole fraction in the gas phase has been studied. The apparent kinetic parameters like reaction order with respect to HCl, Tafel slope and activation energy have been determined from polarization data. The apparent kinetic parameters suggest that the recombination of adsorbed Cl intermediate is the rate determining step.

  14. Effect of Chloride Type on Penetration of Chloride Ions in Concrete

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The influence of chloride type on the diffusivity of chloride ions in concrete was studied by experiment. The result shows that the glectric resistance of concrete and the chloride diffusion coefficient are influenced by chloride type. For the same water/cement ratio (W/C), the diffusion coefficient D in KCl solution is larger than that in NaCl solution; however, the concrete resistance in KCl solution is smaller than that in NaCl solution. The experimental result is analyzed with theory of diffusion.

  15. Influence of Chloride-Ion Adsorption Agent on Chloride Ions in Concrete and Mortar

    Directory of Open Access Journals (Sweden)

    Gai-Fei Peng

    2014-04-01

    Full Text Available The influence of a chloride-ion adsorption agent (Cl agent in short, composed of zeolite, calcium aluminate hydrate and calcium nitrite, on the ingress of chloride ions into concrete and mortar has been experimentally studied. The permeability of concrete was measured, and the chloride ion content in mortar was tested. The experimental results reveal that the Cl agent could adsorb chloride ions effectively, which had penetrated into concrete and mortar. When the Cl agent was used at a dosage of 6% by mass of cementitious materials in mortar, the resistance to the penetration of chloride ions could be improved greatly, which was more pronounced when a combination of the Cl agent and fly ash or slag was employed. Such an effect is not the result of the low permeability of the mortar, but might be a result of the interaction between the Cl agent and the chloride ions penetrated into the mortar. There are two possible mechanisms for the interaction between the Cl agent and chloride ion ingress. One is the reaction between calcium aluminate hydrate in the Cl agent and chloride ions to form Friedel’s salt, and the other one is that calcium aluminate hydrate reacts with calcium nitrite to form AFm during the early-age hydration of mortar and later the NO2− in AFm is replaced by chloride ions, which then penetrate into the mortar, also forming Friedel’s salt. More research is needed to confirm the mechanisms.

  16. Responses of marine unicellular algae to brominated organic compounds in six growth media

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, G.E.; Yoder, M.J.; McLaughlin, L.L.; Lores, E.M.

    1987-12-01

    Marine unicellular algae, Skeletonema costatum, Thalassiosira pseudonana, and Chlorella sp. were exposed to the industrial brominated compounds tetrabromobisphenol A, decabromobiphenyloxide (DBBO), hexabromocyclododecane (HBCD), pentabromomethylbenzene (PBMB), pentabromoethylbenzene (PBEB), and the herbicide bromoxynil (BROM), in six algal growth media. High concentrations of DBBO (1 mg liter-1), PBMB (1 mg liter-1), and PBEB (0.5 mg liter-1) reduced growth by less than 50%. EC50s of the other compounds varied with growth medium, with high EC50/low EC50 ratios between 1.3 and 9.9. Lowest EC50s, 9.3 to 12.0 micrograms liter-1, were obtained with S. costatum and HBCD. It is concluded that responses to toxicants in different media are the results of interactions among algae, growth medium, toxicant, and solvent carrier.

  17. Thinning of CIGS solar cells: Part I: Chemical processing in acidic bromine solutions

    Energy Technology Data Exchange (ETDEWEB)

    Bouttemy, M.; Tran-Van, P. [Institut Lavoisier de Versailles (ILV-UMR 8180 CNRS/UVSQ), 45 av. des Etats Unis, 78035 Versailles (France); Gerard, I., E-mail: gerard@chimie.uvsq.fr [Institut Lavoisier de Versailles (ILV-UMR 8180 CNRS/UVSQ), 45 av. des Etats Unis, 78035 Versailles (France); Hildebrandt, T.; Causier, A. [Institut Lavoisier de Versailles (ILV-UMR 8180 CNRS/UVSQ), 45 av. des Etats Unis, 78035 Versailles (France); Pelouard, J.L.; Dagher, G. [Laboratoire de Photonique et de Nanostructures (LPN-CNRS), route de Nozay 91460 Marcoussis (France); Jehl, Z.; Naghavi, N. [Institut de Recherche et Developpement sur l' Energie Photovoltaique (IRDEP -UMR 7174 CNRS/EDF/Chimie-ParisTech), 6 quai Watier, 78401 Chatou (France); Voorwinden, G.; Dimmler, B. [Wuerth Elektronik Research GmbH, Industriestr. 4, 70565 Stuttgart (Germany); Powalla, M. [Zentrum fuer Sonnenenergie- und Wasserstoff-Forschung (ZSW), Industriestr. 6, 70565 Stuttgart (Germany); Guillemoles, J.F. [Institut de Recherche et Developpement sur l' Energie Photovoltaique (IRDEP -UMR 7174 CNRS/EDF/Chimie-ParisTech), 6 quai Watier, 78401 Chatou (France); Lincot, D. [Laboratoire de Photonique et de Nanostructures (LPN-CNRS), route de Nozay 91460 Marcoussis (France); Etcheberry, A. [Institut Lavoisier de Versailles (ILV-UMR 8180 CNRS/UVSQ), 45 av. des Etats Unis, 78035 Versailles (France)

    2011-08-31

    CIGSe absorber was etched in HBr/Br{sub 2}/H{sub 2}O to prepare defined thicknesses of CIGSe between 2.7 and 0.5 {mu}m. We established a reproducible method of reducing the absorber thickness via chemical etching. We determine the dissolution kinetics rate of CIGSe using trace analysis by graphite furnace atomic absorption spectrometry of Ga and Cu. The roughness of the etching surface decreases during the first 500 nm of the etching to a steady state value of the root-mean-square roughness near 50 nm. X-ray photoelectron spectroscopy analyses demonstrate an etching process occurring with a constant chemical composition of the treated surface acidic bromine solutions provide a controlled chemical thinning process resulting in an almost flat surface and a very low superficial Se{sup 0} enrichment.

  18. Short-lived brominated hydrocarbons – observations in the source regions and the tropical tropopause layer

    Directory of Open Access Journals (Sweden)

    S. Brinckmann

    2012-02-01

    Full Text Available We conducted measurements of the five important short-lived organic bromine species in the marine boundary layer (MBL. Measurements were made in the Northern Hemisphere mid-latitudes (Sylt Island, North Sea in June 2009 and in the tropical Western Pacific during the TransBrom ship campaign in October 2009. For the one-week time series on Sylt Island, mean mixing ratios of CHBr3, CH2Br2, CHBr2Cl and CH2BrCl were 2.0, 1.1, 0.2, 0.1 ppt, respectively. We found maxima of 5.8 and 1.6 ppt for the two main components CHBr3 and CH2Br2. Along the cruise track in the Western Pacific (between 41° N and 13° S we measured mean mixing ratios of 0.9, 0.9, 0.2, 0.1 and 0.1 ppt for CHBr3, CH2Br2, CHBrCl2, CHBr2Cl and CH2BrCl. Air samples with coastal influence showed considerably higher mixing ratios than the samples with open ocean origin. Correlation analyses of the two data sets yielded strong linear relationships between the mixing ratios of four of the five species (except for CH2BrCl. Using a combined data set from the two campaigns and a comparison with the results from two former studies, rough estimates of the molar emission ratios between the correlated substances were: 9/1/0.35/0.35 for CHBr3/CH2Br2/CHBrCl2/CHBr2Cl. Additional measurements were made in the tropical tropopause layer (TTL above Teresina (Brazil, 5° S in June 2008, using balloon-borne cryogenic whole air sampling technique. Near the level of zero clear-sky net radiative heating (LZRH at 14.8 km about 2.25 ppt organic bromine was bound to the five short-lived species, making up 13% of total organic bromine (17.82 ppt. CH2Br2 (1.45 ppt and CHBr3 (0.56 ppt accounted for 90% of the budget of short-lived compounds in that region. Near the

  19. Surface-confined 2D polymerization of a brominated copper-tetraphenylporphyrin on Au(111)

    CERN Document Server

    Smykalla, Lars; Korb, Marcus; Lang, Heinrich; Hietschold, Michael

    2015-01-01

    A coupling-limited approach for the Ullmann reaction-like on-surface synthesis of a two-dimensional covalent organic network starting from a halogenated metallo-porphyrin is demonstrated. Copper-octabromo-tetraphenylporphyrin molecules can diffuse and self-assemble when adsorbed on the inert Au(111) surface. Splitting-off of bromine atoms bonded at the macrocyclic core of the porphyrin starts at room temperature after the deposition and is monitored by X-ray photoelectron spectroscopy for different annealing steps. Direct coupling between the reactive carbon sites of the molecules is, however, hindered by the molecular shape. This leads initially to an ordered non-covalently interconnected supramolecular structure. Further heating to 300{\\deg}C and an additional hydrogen dissociation step is required to link the molecular macrocycles via a phenyl group and form large ordered polymeric networks. This approach leads to a close-packed covalently bonded network of overall good quality. The structures are characte...

  20. Kinetics and mechanism of the oxidation of some -hydroxy acids by hexamethylenetetramine-bromine

    Indian Academy of Sciences (India)

    Dimple Garg; Seema Kothari

    2004-11-01

    The oxidation of lactic acid, mandelic acid and ten monosubstituted mandelic acids by hexamethylenetetramine-bromine (HABR) in glacial acetic acid, leads to the formation of the corresponding oxoacid. The reaction is first order with respect to each of the hydroxy acids and HABR. It is proposed that HABR itself is the reactive oxidizing species. The oxidation of -deuteriomandelic acid exhibits the presence of a substantial kinetic isotope effect (/ = 5.91 at 298 K). The rates of oxidation of the substituted mandelic acids show excellent correlation with Brown’s + values. The reaction constants are negative. The oxidation exhibits an extensive cross conjugation between the electron-donating substituent and the reaction centre in the transition state. A mechanism involving transfer of a hydride ion from the acid to the oxidant is postulated.

  1. Hydrothermal Synthesis of Mesoporous Nanocrystalline Tetragonal ZrO2 Using Dehydroabietyltrimethyl Ammonium Bromine

    Directory of Open Access Journals (Sweden)

    Peng Wang

    2015-01-01

    Full Text Available Mesoporous nanocrystalline tetragonal zirconias were successfully synthesized through a hydrothermal method using a novel bioresource-derived quaternary ammonium salt, dehydroabietyltrimethyl ammonium bromine (DTAB, as a templating agent. The templating agent provides a surface area (242.02 m2/g, high pore volume (0.53 cm3/g, and large average pore diameter (7.65 nm, which suggests that DTAB is a good candidate for mesostructure synthesis. The hydrothermal treatments give the materials improved thermal stabilities because of the generation of tetragonal nanocrystallites that are more stable than the bulk amorphous ones in the hydrothermal process. However, because of the absence of stabilizers, the sizes of the crystallites of the as-synthesized sample increase gradually with increasing calcination temperature. As the crystalline size of the sample rises to 25 nm, the nanocrystallites become too large to integrate well together, causing the well-organized mesostructure to collapse.

  2. 42 CFR 84.250 - Vinyl chloride respirators; description.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Vinyl chloride respirators; description. 84.250... Respirators § 84.250 Vinyl chloride respirators; description. Vinyl chloride respirators, including all... escape from vinyl chloride atmospheres containing adequate oxygen to support life, are...

  3. Co-leaching of brominated compounds and antimony from bottled water.

    Science.gov (United States)

    Andra, Syam S; Makris, Konstantinos C; Shine, James P; Lu, Chensheng

    2012-01-01

    A fast-growing bottled water market is occasionally challenged by reports calling for contaminant leaching from water-contact materials (plastics). Our focus was on leaching of antimony (Sb) and brominated compounds expressed by total soluble bromine (Br) measurements, including those of polybrominated diphenyl ethers (PBDE). Studies are lacking on concomitant leaching of two or more inorganic plastic constituents from the same bottle. A market-representative basket survey of bottled water was initiated in Boston, USA supermarkets. Bottled water classes sampled were: i) non-carbonated (NCR), ii) carbonated (CR), and iii) non-carbonated and enriched (NCRE). Plastic bottle materials sampled were: polyethylene terephthalate (PET), high-density polyethylene (HDPE), polystyrene (PS), and polycarbonate (PC). Storage conditions for the 31 bottled water samples were: 23°C temperature, no-shaking and 12h/12h light/dark for 60days of equilibration. Average Br and Sb concentrations after 60-days of storage followed the order of NCR

  4. Meteorological controls on the vertical distribution of bromine monoxide in the lower troposphere

    Directory of Open Access Journals (Sweden)

    P. K. Peterson

    2014-09-01

    Full Text Available Multiple axis differential absorption spectroscopy (MAX-DOAS measurements of bromine monoxide (BrO probed the vertical structure of halogen activation events during March–May 2012 at Barrow, Alaska. An analysis of the BrO averaging kernels and degrees of freedom obtained by optimal-estimation-based inversions from raw MAX-DOAS measurements reveals the information is best represented by reducing the retrieved BrO profile to two quantities, the integrated column from the surface through 200 m (VCD200 m, and the lower tropospheric vertical column density (LT-VCD which represents the integrated column of BrO from the surface through 2 km. The percentage of lower-tropospheric BrO in the lowest 200 m was found to be highly variable ranging from shallow layer events, where BrO is present primarily in the lowest 200 m to distributed column events where BrO is observed at higher altitudes. The highest observed LT-VCD events occurred when BrO was distributed throughout the lower troposphere, rather than concentrated near the surface. Atmospheric stability in the lowest 200 m influenced the percentage of LT-VCD that is in the lowest 200 m, with inverted temperature structures having a first-to-third quartile range (Q1–Q3 of VCD200 m/LT-VCD from 15–39% while near neutral temperature structures had a Q1–Q3 range of 7–13%. Data from this campaign show no clear influence of wind speed on either lower-tropospheric bromine activation (LT-VCD or the vertical distribution of BrO, while examination of seasonal trends and the temperature dependence of the vertical distribution supported the conclusion that the atmospheric stability affects the vertical distribution of BrO.

  5. Scientific Opinion on Emerging and Novel Brominated Flame Retardants (BFRs in Food

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Contaminants in the Food Chain (CONTAM

    2012-10-01

    Full Text Available EFSA was asked to deliver a scientific opinion on brominated flame retardants (BFRs other than PBDEs, PBBs, HBCDDs, TBBPA and brominated phenols and their derivatives. The BFRs that are the subject of the current opinion, were classified in groups termed ‘emerging’ and ‘novel’ BFRs. Information on 17 emerging and 10 novel BFRs was collected. The information varied widely for these BFRs. There is a lack of experimental data on physico-chemical characteristics, stability/reactivity and current use and production volume of all the emerging and novel BFRs. Due to the very limited information on occurrence, exposure and toxicity, the CONTAM Panel could not perform a risk characterisation for any of the BFRs considered. Instead, an attempt was made to identify those BFRs that could be a potential health concern and should be considered first for future investigations. For this purpose the Panel first evaluated the available experimental data on occurrence in food, behaviour in the environment and toxicity. Secondly, a modelling exercise was performed focussing on the potential of the emerging and novel BFRs for persistence in the environment and for their possible bioaccumulation potential. There is convincing evidence that tris(2,3-dibromopropyl phosphate (TDBPP and dibromoneopentyl glycol (DBNPG are genotoxic and carcinogenic, warranting further surveillance of their occurrence in the environment and in food. Based on the limited experimental data on environmental behaviour, 1,2-bis(2,4,6-tribromophenoxyethane (BTBPE and hexabromobenzene (HBB were identified as compounds that could raise a concern for bioaccumulation. For the modelling exercise, the CONTAM Panel selected two environmental characteristics, overall persistence and potential for bioaccumulation, as being most relevant to provide insight into the possibility that emerging or novel BFRs might accumulate in the food chain, and thus might appear in food intended for human

  6. Associations between brominated flame retardants in house dust and hormone levels in men

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Paula I. [Department of Environmental Health Sciences, University of Michigan, 1415 Washington Heights, Ann Arbor, MI 48109 (United States); Stapleton, Heather M. [Nicholas School of the Environment, Box 90328, Duke University, Durham, NC 27708 (United States); Mukherjee, Bhramar [Department of Biostatistics, University of Michigan, 1415 Washington Heights, Ann Arbor, MI 48109 (United States); Hauser, Russ [Department of Environmental Health, Harvard School of Public Health, 677 Huntington Ave., Boston, MA 02115 (United States); Meeker, John D., E-mail: meekerj@umich.edu [Department of Environmental Health Sciences, University of Michigan, 1415 Washington Heights, Ann Arbor, MI 48109 (United States)

    2013-02-15

    Brominated flame retardants (BFRs) are used in the manufacture of a variety of materials and consumer products in order to meet fire safety standards. BFRs may persist in the environment and have been detected in wildlife, humans and indoor dust and air. Some BFRs have demonstrated endocrine and reproductive effects in animals, but human studies are limited. In this exploratory study, we measured serum hormone levels and flame retardant concentrations [31 polybrominated diphenyl ether (PBDE) congeners and 6 alternate flame retardants] in house dust from men recruited through a US infertility clinic. PBDE congeners in dust were grouped by commercial mixtures (i.e. penta-, octa- and deca-BDE). In multivariable linear regression models adjusted by age and body mass index (BMI), significant positive associations were found between house dust concentrations of pentaBDEs and serum levels of free T4, total T3, estradiol, and sex hormone binding globulin (SHBG), along with an inverse association with follicle stimulating hormone (FSH). There were also positive associations of octaBDE concentrations with serum free T4, thyroid stimulating hormone (TSH), luteinizing hormone (LH) and testosterone and an inverse association of decaBDE concentrations with testosterone. Hexabromocyclododecane (HBCD) was associated with decreased SHBG and increased free androgen index. Dust concentrations of bis-tribromophenoxyethane (BTBPE) and tetrabromo-diethylhexylphthalate (TBPH) were positively associated with total T3. These findings are consistent with our previous report of associations between PBDEs (BDE 47, 99 and 100) in house dust and hormone levels in men, and further suggest that exposure to contaminants in indoor dust may be leading to endocrine disruption in men. - Highlights: ► Brominated flame retardants (BFRs) including PBDEs and alternates were measured. ► Exposure to BFRs is characterized from concentrations in participant vacuum bag dust. ► Exposure to PBDEs and

  7. UTILIZATION OF BROMINATION REACTION FOR THE SPECTROPHOTOMETRIC ASSAY OF DOMPERIDONE IN PHARMACEUTICALS

    Directory of Open Access Journals (Sweden)

    O. ZENITA DEVI

    2011-03-01

    Full Text Available Three simple and sensitive spectrophotometric methods are described for the determination of domperidone (DOM in bulk drug and in dosage forms using bromate-bromide mixture as brominating agent in acid medium and three dyes, meta-cresol purple (MCP, amaranth (AMR and erioglaucine (EGC. The methods involve the addition of a known excess of bromate-bromide mixture to an acidified solution of DOM followed by the determination of the residual bromine by reacting with a fixed amount of either MCP dye and measuring the absorbance at 530 nm (method A or AMR dye and measuring the absorbance at 520 nm (method B or EGC dye and measuring the absorbance at 630 nm (method C. Beer’s law is obeyed over the concentration ranges, 0.63–10.0, 0.25-4.0 and 0.13-2.0 µg mL-1 for method A, B and C, respectively. The ap¬parent molar absorptivities are calculated to be 3.751x104, 6.604x104 and 1.987x105 L mol-1cm-1 for method A, B and C, respectively, and the corresponding sandell sensitivity values are 0.011, 0.006 and 0.002 μg cm-2. The limit of detection and the limit of quantification are also reported for all the three methods. No interference was observed from common additives found in pharmaceutical preparations. Statistical comparisons of the results with those of the reference method showed excellent agreement, and indicated no significant difference in accuracy and precision. The accuracy and reliability of the methods were further ascertained by performing recovery tests via standardaddition technique.

  8. Brominated flame retardants in children's toys: concentration, composition, and children's exposure and risk assessment.

    Science.gov (United States)

    Chen, She-Jun; Ma, Yun-Juan; Wang, Jing; Chen, Da; Luo, Xiao-Jun; Mai, Bi-Xian

    2009-06-01

    Brominated flame retardants (BFRs), including polybrominated diphenyl ethers (PBDEs), 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE), decabromodiphenyl ethane (DBDPE), and polybrominated biphenyls (PBBs) were found in children's toys purchased from South China. The median BFR concentrations in the hard plastic toys were 53,000, 5540 ng/g, 101.1 ng/g, and 27.9 ng/g, fortotal PBDEs, DBDPE, BTBPE, and PBBs, respectively,which were notably higher than values in other toys. The PBDE concentrations were below the threshold limit (1000 ppm) required bythe European Commission's Restriction of Hazardous Substances (RoHS) and Waste Electrical and Electronic Equipment (WEEE) directives in all of the toys, except for one hard plastic toy with a total PBDE concentration of 5,344,000 ng/g. The BFR profiles in the toys were consistent with the patterns of their current production and consumption in China, where PBDEs, specifically decaBDE product, were the dominant BFR, followed by the emerging DBDPE. The relatively high concentrations of octa- and nonaBDEs in the foam toys and the results of principal component analysis (PCA) may suggest the decomposition of highly brominated BDEs during the manufacturing processes of the toys. Daily total PBDE exposures associated with toys via inhalation, mouthing, dermal contact, and oral ingestion ranged from 82.6 to 8992 pg/kg bw-day for children of 3 months to 14 years of age. Higher exposures, predominantly contributed through the mouthing pathway, were observed for infants and toddlers than for the other subgroups. In most cases, children's BFR exposure via the toys likely accounts for a small proportion of their daily BFR exposure, and the hazard quotients for noncancer risk evaluation were far below 1. To the author's knowledge, this is the first study to examine the concentrations of BFRs in toys, and the potential exposures to children.

  9. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    Directory of Open Access Journals (Sweden)

    H. Guan

    2009-09-01

    Full Text Available Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the CMB approach. Furthermore, intensive vegetation clearance for agriculture, for example during the European settlement in many coastal areas of Australia, may have perturbed catchment chloride balance conditions for appropriate use in CMB applications. In order to deal with these issues, a high resolution chloride deposition map in the coastal region is needed. In this study, we examined geographic, orographic, and atmospheric factors influencing chloride deposition in the Mount Lofty Ranges (MLR, a coastal hilly area of approximately 9000 km2 spatial extent in South Australia, using partial correlation and regression analyses. The results indicate that coastal distance, and terrain aspect and slope are two most significant factors controlling chloride deposition. Coastal distance accounts for 65% spatial variability in chloride deposition, with terrain aspect and slope for 8%. The deposition gradient is about 0.08 gm-2 year-1 km-1 as one progresses inland. The results are incorporated into a published de-trended residual kriging approach (ASOADeK to produce a 1 km×1 km resolution annual chloride deposition map and a bulk precipitation chloride concentration map. The average uncertainty of the deposition map is about 30% in the western MLR, and over 50% in the eastern MLR. The maps will form a very useful basis for examining catchment chloride balances for use in the CMB application in the study area.

  10. Slow Phospholipid Exchange between a Detergent-Solubilized Membrane Protein and Lipid-Detergent Mixed Micelles Brominated Phospholipids as Tools to Follow Its Kinetics

    DEFF Research Database (Denmark)

    Montigny, Cédric; Dieudonné, Thibaud; Orlowski, Stéphane

    2017-01-01

    Membrane proteins are largely dependent for their function on the phospholipids present in their immediate environment, and when they are solubilized by detergent for further study, residual phospholipids are critical, too. Here, brominated phosphatidylcholine, a phospholipid which behaves as an ...

  11. A comprehensive probabilistic model of chloride ingress in unsaturated concrete

    OpenAIRE

    Bastidas-Arteaga, Emilio; Chateauneuf, Alaa; Sánchez-Silva, Mauricio; Bressolette, Philippe; Schoefs, Franck

    2011-01-01

    International audience; Corrosion induced by chloride ions has become a critical issue for many reinforced concrete structures. The chloride ingress into concrete has been usually simplified as a diffusion problem where the chloride concentration throughout concrete is estimated analytically. However, this simplified approach has several limitations. For instance, it does not consider chloride ingress by convection which is essential to model chloride penetration in unsaturated conditions as ...

  12. Inhibition of nitrite-induced toxicity in channel catfish by calcium chloride and sodium chloride

    Science.gov (United States)

    Tommasso J.R., Wright; Simco, B.A.; Davis, K.B.

    1980-01-01

    Environmental chloride has been shown to inhibit methemoglobin formation in fish, thereby offering a protective effect against nitrite toxicity. Channel catfish (Ictalurus punctatus) were simultaneously exposed to various environmental nitrite and chloride levels (as either CaCl2 or NaCl) in dechlorinated tap water (40 mg/L total hardness, 47 mg/L alkalinity, 4 mg/L chloride, pH = 6.9-7.1, and temperature 21-24°C). Methemoglobin levels in fish simultaneously exposed to 2.5 mg/L nitrite and up to 30 mg/L chloride as either CaCl2 or NaCl were similar but significantly lower than in unprotected fish. Exposure to 10 mg/L nitrite and 60 mg/L chloride resulted in methemoglobin levels similar to those of the controls; most unprotected fish died. Fish exposed to 10 mg/L nitrite had significantly lower methemoglobin levels when protected with 15.0 mg/L chloride as CaCl2 than with NaCl. Fish exposed to nitrite in the presence of 60 mg/L chloride (as either CaCl2 or NaCl) had similar 24-h LC50 values that were significantly elevated above those obtained in the absence of chloride. Calcium had little effect on tolerance to nitrite toxicity in channel catfish in contrast to its large effect reported in steelhead trout (Salmo gairdneri).

  13. Congenital Chloride Diarrhea: Diagnosis by Easy-Accessible Chloride Measurement in Feces

    Directory of Open Access Journals (Sweden)

    C. Gils

    2016-01-01

    Full Text Available Background. Congenital chloride diarrhea (CCD is an autosomal recessive disorder caused by mutations in the genes encoding the intestinal Cl−/HCO3- exchanger and is clinically characterized by watery, profound diarrhea, electrolyte disturbances, and metabolic alkalosis. The CCD diagnosis is based on the clinical symptoms and measurement of high chloride concentration in feces (>90 mmol/L and is confirmed by DNA testing. Untreated CCD is lethal, while long-term clinical outcome improves when treated correctly. Case Presentation. A 27-year-old woman had an emergency caesarian due to pain and discomfort in gestational week 36 + 4. The newborn boy had abdominal distension and yellow fluid per rectum. Therapy with intravenous glucose and sodium chloride decreased his stool frequency and improved his clinical condition. A suspicion of congenital chloride diarrhea was strongly supported using blood gas analyzer to measure an increased chloride concentration in the feces; the diagnosis was confirmed by DNA testing. Discussion. Measurement of chloride in feces using an ordinary blood gas analyzer can serve as a preliminary analysis when congenital chloride diarrhea is suspected. This measurement can be easily performed with a watery feces composition. An easy-accessible chloride measurement available will facilitate the diagnostics and support the initial treatment if CCD is suspected.

  14. Amine and Titanium (IV Chloride, Boron (III Chloride or Zirconium (IV Chloride-Promoted Baylis-Hillman Reactions

    Directory of Open Access Journals (Sweden)

    Shi-Cong Cui

    2001-10-01

    Full Text Available The Baylis-Hillman reactions of various aryl aldehydes with methyl vinyl ketone at temperatures below -20oC using Lewis acids such as titanium (IV chloride, boron (III chloride or zirconium (IV chloride in the presence of a catalytic amount of selected amines used as a Lewis bases afford the chlorinated compounds 1 as the major product in very high yields. Acrylonitrile can also undergo the same reaction to give the corresponding chlorinated product in moderate yield. A plausible reaction mechanism is proposed. However, if the reaction was carried out at room temperature (ca. 20oC, then the Z-configuration of the elimination product 3, derived from 1, was formed as the major product.

  15. Synthesis of Trans-5-propyl-2-(4'-bromine-phenyl)-tetrahydropyran%反-5-丙基-2-(4'-溴-苯基)-四氢吡喃的合成

    Institute of Scientific and Technical Information of China (English)

    高丰琴; 何汉江; 郭强; 王小明; 李鹏; 张彦军

    2012-01-01

    以对溴苯甲酸为起始原料,经酰化后生成酰氯,酰氯与N,O-二甲基羟胺盐酸盐反应生成酰胺,再与氯乙烯基镁反应生成α,β不饱和酬. 同时,正戊醛与二正丙胺反应生成烯胺.α,β不饱和酬与烯胺经迈克尔加成反应生成分子内醛酮,分子内醛酮经关环反应、乙醇重结晶可得到色谱纯度99.5%以上的反-5-丙基-2-(4'-溴-苯基)-四氢吡喃.%The starting material of 4-bromobenzene carboxylic acid was aeylated to generate aeyl chloride. Then,acyl chloride reacted with N, O-dimethyl hydroxylamine hydrochloride to synthesize the amides, which then reacted with chlorovinylmagnesium to synthesize α, β unsaturated ketone. Meanwhile, allyl amine was synthesized from the reaction of pentanal with di-n-propylamine. By Michael addition reaction, α,β unsaturated ketone and allyl amine reacted to synthesize intramolecular aldehyde and ketone, which further reacted to synthesize trans-5-pmpyl-2-( 4'-bromine-phenyl ) -tetrahydropyran (3PyPBr) with a purity of more than 99.5% by closed loop reaction and recrystallization with ethanol.

  16. Levels and congener profiles of polybrominated diphenyl ethers (PBDEs) in breast milk from Shanghai: implication for exposure route of higher brominated BDEs.

    Science.gov (United States)

    Ma, Shengtao; Yu, Zhiqiang; Zhang, Xiaolan; Ren, Guofa; Peng, Ping'an; Sheng, Guoying; Fu, Jiamo

    2012-07-01

    Breast milk has been widely used as a bioindicator to assess the extent of human exposure to PBDEs via various exposure routes. In this study, 48 breast milk samples were collected from primiparous women in Shanghai city, and 14 PBDEs congeners (BDE-28, -47, -99, -100, -153, -154, -183, -196, -197, -203, -206, -207, -208, and -209) were quantified using gas chromatography-electron capture negative ionization-mass spectrometry. The mean concentration of total PBDEs was 8.6 ng/g lipid weight, and ranged from 1.8 to 26.7 ng/g lipid weight. These concentration levels were similar to those reported in Europe and Asia, but one order of magnitude lower than those in North America. The congener profiles in this study exhibited a specific pattern in human milk found worldwide, BDE-153 and BDE-28 accounted for a relatively higher proportion of lower brominated BDEs (from tri- to hepta-BDEs), whereas higher brominated BDEs (from octa- to deca-BDEs) contributed more than 70% of the total PBDEs. The Spearman's correlation coefficient among higher brominated BDEs showed a positive relationship, and concentration levels of higher brominated BDEs were statistically different between office workers and housewives. Due to relatively higher proportion of PBDEs from octa- to deca-BDEs were detected, air inhalation and dust ingestion might be the major exposure routes of higher brominated BDEs. Further research is needed to clarify the major exposure route of higher brominated BDEs to humans.

  17. Dynamic Electrochemical Measurement of Chloride Ions.

    Science.gov (United States)

    Abbas, Yawar; de Graaf, Derk B; Olthuis, Wouter; van den Berg, Albert

    2016-02-05

    This protocol describes the dynamic measurement of chloride ions using the transition time of a silver silver chloride (Ag/AgCl) electrode. Silver silver chloride electrode is used extensively for potentiometric measurement of chloride ions concentration in electrolyte. In this measurement, long-term and continuous monitoring is limited due to the inherent drift and the requirement of a stable reference electrode. We utilized the chronopotentiometric approach to minimize drift and avoid the use of a conventional reference electrode. A galvanostatic pulse is applied to an Ag/AgCl electrode which initiates a faradic reaction depleting the Cl- ions near the electrode surface. The transition time, which is the time to completely deplete the ions near the electrode surface, is a function of the ion concentration, given by the Nernst equation. The square root of the transition time is in linear relation to the chloride ion concentration. Drift of the response over two weeks is negligible (59 µM/day) when measuring 1 mM [Cl-]using a current pulse of 10 Am(-2). This is a dynamic measurement where the moment of transition time determines the response and thus is independent of the absolute potential. Any metal wire can be used as a pseudo-reference electrode, making this approach feasible for long-term measurement inside concrete structures.

  18. Chloride binding site of neurotransmitter sodium symporters.

    Science.gov (United States)

    Kantcheva, Adriana K; Quick, Matthias; Shi, Lei; Winther, Anne-Marie Lund; Stolzenberg, Sebastian; Weinstein, Harel; Javitch, Jonathan A; Nissen, Poul

    2013-05-21

    Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs have a serine. The LeuT-E290S mutant displays chloride-dependent activity. We show that, in LeuT-E290S cocrystallized with bromide or chloride, the anion is coordinated by side chain hydroxyls from Tyr47, Ser290, and Thr254 and the side chain amide of Gln250. The bound anion and the nearby sodium ion in the Na1 site organize a connection between their coordinating residues and the extracellular gate of LeuT through a continuous H-bond network. The specific insights from the structures, combined with results from substrate binding studies and molecular dynamics simulations, reveal an anion-dependent occlusion mechanism for NSS and shed light on the functional role of chloride binding.

  19. Chloride equilibrium potential in salamander cones

    Directory of Open Access Journals (Sweden)

    Bryson Eric J

    2004-12-01

    Full Text Available Abstract Background GABAergic inhibition and effects of intracellular chloride ions on calcium channel activity have been proposed to regulate neurotransmission from photoreceptors. To assess the impact of these and other chloride-dependent mechanisms on release from cones, the chloride equilibrium potential (ECl was determined in red-sensitive, large single cones from the tiger salamander retinal slice. Results Whole cell recordings were done using gramicidin perforated patch techniques to maintain endogenous Cl- levels. Membrane potentials were corrected for liquid junction potentials. Cone resting potentials were found to average -46 mV. To measure ECl, we applied long depolarizing steps to activate the calcium-activated chloride current (ICl(Ca and then determined the reversal potential for the current component that was inhibited by the Cl- channel blocker, niflumic acid. With this method, ECl was found to average -46 mV. In a complementary approach, we used a Cl-sensitive dye, MEQ, to measure the Cl- flux produced by depolarization with elevated concentrations of K+. The membrane potentials produced by the various high K+ solutions were measured in separate current clamp experiments. Consistent with electrophysiological experiments, MEQ fluorescence measurements indicated that ECl was below -36 mV. Conclusions The results of this study indicate that ECl is close to the dark resting potential. This will minimize the impact of chloride-dependent presynaptic mechanisms in cone terminals involving GABAa receptors, glutamate transporters and ICl(Ca.

  20. Chemistry of recoil atoms of bromine-82 in neutron-irradiated crystalline perbromates of the alkali metals and ammonium

    Energy Technology Data Exchange (ETDEWEB)

    Gavrilov, V.V.; Isupov, V.K.; Kirin, I.S.

    1975-01-01

    It was established by ion exchange chromatography that the recoil atoms of bromine-82 in perbromates with thermal neutrons are stabilized in the form of five valence forms: BrO/sub 4//sup -/, BrO/sub 3//sup -/, BrO/sub 2//sup -/, BrO/sup -/, Br/sup -/. The retention of bromine-82 of BrO/sub 4//sup -/ is 2.1 +- 0.4 percent for LiBrO/sub 4/, 2.1 +- 0.4 percent for NaBrO/sub 4/, 2.3 +- 0.4 percent for KBrO/sub 4/, 2.6 +- 0.4 percent for RbBrO/sub 4/, 2.2 +- 0.4 percent for CsBrO/sub 4/, and 1.6 +- 0.4 percent for NH/sub 4/BrO/sub 4/.

  1. The mercury species and their association with carbonaceous compositions, bromine and iodine in PM2.5 in Shanghai.

    Science.gov (United States)

    Duan, Lian; Xiu, Guangli; Feng, Ling; Cheng, Na; Wang, Chenggang

    2016-03-01

    PM2.5 samples were collected in south Shanghai from November 2013 to October 2014. The species of particulate bounded mercury (PBM), including hydrochloric soluble particle-phase mercury (HPM), element soluble particle-phase mercury (EPM) and residual soluble particle-phase mercury (RPM), were determined in PM2.5. The chemical composition of PM2.5 including organic carbon (OC) and elemental carbon (EC), total bromine and iodine were also analyzed. The results showed that the annual average concentration of PBM was 0.30 ± 0.31 ng m(-3) and 0.34 ± 0.32 ng m(-3) in winter, 0.31 ± 0.19 ng m(-3) in spring, 0.30 ± 0.45 ng m(-3) in fall and 0.28 ± 0.17 ng m(-3) in summer. HPM took the highest fraction 51.2% in PBM, followed by RPM 27.7% and EPM 21.1%. EC positively correlated to particle mercury, especially in winter (r = 0.70), the same for OC in winter (r = 0.72), which indicated that the carbonaceous composition may affect the transformation of Hg in the atmosphere. Mercury species showed different correlations with bromine and iodine in the four seasons. The strongest correlation between bromine, iodine and mercury was found in spring and fall, respectively. Bromine showed the stronger correlation with total mercury and speciated particle mercury than iodine. In addition, the days were classified into haze and non-haze days based on the visibility and relative humidity, while the ratio of HPM in haze days was much higher than that in non-haze days. EC strongly correlated with PBM during haze and non-haze days while OC only positively correlated with PBM in non-haze days, this may indicate that the different carbonaceous part may affect PBM differently.

  2. Impact of biogenic very short-lived bromine on the Antarctic ozone hole during the 21st century

    OpenAIRE

    Fernandez, Rafael P.; Kinnison, Douglas E.; Lamarque, Jean-Francois; Tilmes, Simone; Saiz-Lopez, Alfonso

    2017-01-01

    Active bromine released from the photochemical decomposition of biogenic very short-lived bromocarbons (VSLBr) enhances stratospheric ozone depletion. Based on a dual set of 1960–2100 coupled chemistry–climate simulations (i.e. with and without VSLBr), we show that the maximum Antarctic ozone hole depletion increases by up to 14 % when natural VSLBr are considered, which is in better agreement with ozone observations. The impact of the additional 5 pptv VSLBr on Antarctic...

  3. Impact of biogenic very short-lived bromine on the Antarctic ozone hole during the 21st century

    OpenAIRE

    Fernandez, Rafael P.; Kinnison, Douglas E.; Lamarque, Jean-Francois; Tilmes, Simone; Saiz-Lopez, Alfonso

    2016-01-01

    Active bromine released from the photochemical decomposition of biogenic very short-lived bromocarbons (VSLBr) enhances stratospheric ozone depletion. Based on a dual set of 1960–2100 coupled chemistry-climate simulations (i.e. with and without VSLBr), we show that the maximum Antarctic ozone hole depletion increases by up to 14 % when natural VSLBr are considered, in better agreement with ozone observations. The impact of the additional 5 pptv VSLBr on Antarctic ozone is ...

  4. Temporal development of brominated flame retardants in peregrine falcon (Falco peregrinus) eggs from South Greenland (1986-2003)

    DEFF Research Database (Denmark)

    Vorkamp, Katrin; Thomsen, Marianne; Falk, Knud;

    2005-01-01

    A time trend between 1986 and 2003 was found for brominated flame retardants in peregrine falcon eggs from South Greenland, with significantly increasing concentrations of the polybrominated diphenyl ethers (PBDEs) 99, 100, 153, 154, and 209. For BDE-99 and -100, the concentration increased...... with increasing time trends exist for the BDEs 99, 100, 153, 154, and 209, while a decreasing contamination with the BDEs 183, 49, 47, 66 and 153 was indicated in a subset of eggs....

  5. An Empirical Approach to Determining the Boundary Layer Bromine Monoxide (BrO) Abundance from Satellite Total Column Measurements

    Science.gov (United States)

    Simpson, W. R.; Donohoue, D.; Carlson, D. A.

    2009-12-01

    Unique chemistry in the Arctic boundary layer during springtime liberates bromine from sea salt, producing reactive halogen gases (e.g. atomic bromine and bromine monoxide radicals) that then drastically alter atmospheric oxidation pathways. This phenomenon causes ozone depletion events and affects mercury deposition to the snowpack. Satellite remote sensing (e.g. OMI and GOME2 observations) techniques can detect the total column abundance of BrO, which is generally the primary species of the reactive bromine family. However, BrO is also present in the stratosphere, so it is necessary to partition the satellite-observed BrO column abundance into boundary layer and non-boundary layer (primarily stratospheric) partial columns to be able to infer boundary layer abundances and hence chemical affects near the Earth's surface (i.e. ozone and mercury impacts). In this presentation, we describe an empirical method for partitioning the BrO total column and apply it globally during spring 2008. The method indicates that some BrO total column enhancements ("hotspots") are not actually enhancements in the boundary layer BrO abundance but occur aloft. Movies and a statistical analysis of the inferred boundary layer BrO abundance are presented. The method has been tested and performs well at the Barrow field site. However, in areas that lack routine ground truth BrO measurements (e.g. Hudson Bay, Canada), large tropospheric BrO abundances are indicated. It is not clear if these inferred boundary layer BrO events are real or if the simple empirical method described here is failing in those locations. Verification of this method over large spatial regions of the Arctic is needed.

  6. Utilization of a Green Brominating Agent for the Spectrophotometric Determination of Pipazethate HCl in Pure Form and Pharmaceutical Preparations

    Directory of Open Access Journals (Sweden)

    Ayman A. Gouda

    2013-01-01

    Full Text Available Five simple, accurate, and sensitive spectrophotometric methods (A–E have been described for the indirect assay of pipazethate HCl (PZT either in pure form or in pharmaceutical preparations. The proposed methods are based on the bromination of pipazethate HCl with a solution of excess bromate-bromide mixture in hydrochloric acid medium and subsequent estimation of the residual bromine by different reaction schemes. In the first three methods (A–C, the determination of the residual bromine is based on its ability to bleach the color of methyl orange, indigo carmine, or thymol blue dyes and measuring the absorbance at 520, 610, and 550 nm for methods A, B, and C, respectively. Methods D and E involves treating the unreacted bromine with a measured excess of iron(II, and the remaining iron(II is complexed with 1,10-phenanthroline, and the increase in absorbance is measured at 510 nm for method D and the resulting iron(III is complexed with thiocyanate and the absorbance is measured at 480 nm for method E. The different experimental parameters affecting the development and stability of the color are carefully studied and optimized. Regression analysis of the Beer-Lambert plots showed good correlation in the concentration ranges of 0.5–8.0 μg . The apparent molar absorptivity, Sandell's sensitivity, detection and quantitation limits were evaluated. The proposed methods have been applied and validated successfully for the analysis of the drug in its pure form and pharmaceutical formulations with mean recoveries of 99.94%–100.15% and relative standard deviation ≤1.53. No interference was observed from a common pharmaceutical adjuvant. Statistical comparison of the results with the reference method shows excellent agreement and indicates no significant difference in accuracy and precision.

  7. [Formation of disinfection by-products by Microcystis aeruginosa intracellular organic matter: comparison between chlorination and bromination].

    Science.gov (United States)

    Tian, Chuan; Guo, Ting-Ting; Liu, Rui-Ping; Jefferson, William; Liu, Hui-Juan; Qu, Jiu-Hui

    2013-11-01

    In order to illustrate the effects of released algal organic matter in cyanobacteria blooms on raw water quality and water treatment process, intracellular organic matter (IOM) of Microcystis aeruginosa, which is the dominant species in cyanobacteria blooms, was chosen as a precursor and characterized. In addition, the transformation of IOM and the formation of disinfection byproducts were evaluated at different pH of 6.5, 7.1 and 8.4 after chlorination or bromination, with subsequent correlation analysis. The results indicated that IOM was primarily composed of macromolecular matter, i. e. , the species with relative molecular weight of > 30 x 10(3), constituting 68.8% of dissolved organic carbon (DOC). Fluorescence excitation-emission matrix indicated that IOM was mainly composed of aromatic protein-like matter with an intensity of 92.6 AU x L x mg(-1). After reaction with chlorine or bromine, the intensity of aromatic protein-like peaks decreased sharply by 76.6% - 93.3%, and its reduction correlated well with the formation of trihalomethane (THMs, R2 = 0.81) and haloacetic acid (HAAs, R2 = 0.77). The formation of THMs and HAAs increased with the increase in pH. Compared with chlorine, bromine formed more THMs and HAAs, and tended to form highly halogenated HAAs. However, with increasing pH, the reactivity with IOM between chlorine and bromine was closer, i.e, k(OBr-IOM)/k(OCl-(IOM) < k(HOBr-IOM/k(HOCl-IOM).

  8. Efficient cellulose solvent: quaternary ammonium chlorides.

    Science.gov (United States)

    Kostag, Marc; Liebert, Tim; El Seoud, Omar A; Heinze, Thomas

    2013-10-01

    Pure quaternary tetraalkylammonium chlorides with one long alkyl chain dissolved in various organic solvents constitute a new class of cellulose solvents. The electrolytes are prepared in high yields and purity by Menshutkin quaternization, an inexpensive and easy synthesis route. The pure molten tetraalkylammonium chlorides dissolve up to 15 wt% of cellulose. Cosolvents, including N,N-dimethylacetamide (DMA), may be added in large excess, leading to a system of decreased viscosity. Contrary to the well-established solvent DMA/LiCl, cellulose dissolves in DMA/quaternary ammonium chlorides without any pretreatment. Thus, the use of the new solvent avoids some disadvantages of DMA/LiCl and ionic liquids, the most extensively employed solvents for homogeneous cellulose chemistry.

  9. Alkali metal and ammonium chlorides in water and heavy water (binary systems)

    CERN Document Server

    Cohen-Adad, R

    1991-01-01

    This volume surveys the data available in the literature for solid-fluid solubility equilibria plus selected solid-liquid-vapour equilibria, for binary systems containing alkali and ammonium chlorides in water or heavy water. Solubilities covered are lithium chloride, sodium chloride, potassium chloride, rubidium chloride, caesium chloride and ammonium chloride in water and heavy water.

  10. Probing the subtropical lowermost stratosphere and the tropical upper troposphere and tropopause layer for inorganic bromine

    Science.gov (United States)

    Werner, Bodo; Stutz, Jochen; Spolaor, Max; Scalone, Lisa; Raecke, Rasmus; Festa, James; Fedele Colosimo, Santo; Cheung, Ross; Tsai, Catalina; Hossaini, Ryan; Chipperfield, Martyn P.; Taverna, Giorgio S.; Feng, Wuhu; Elkins, James W.; Fahey, David W.; Gao, Ru-Shan; Hintsa, Erik J.; Thornberry, Troy D.; Moore, Free Lee; Navarro, Maria A.; Atlas, Elliot; Daube, Bruce C.; Pittman, Jasna; Wofsy, Steve; Pfeilsticker, Klaus

    2017-01-01

    We report measurements of CH4 (measured in situ by the Harvard University Picarro Cavity Ringdown Spectrometer (HUPCRS) and NOAA Unmanned Aircraft System Chromatograph for Atmospheric Trace Species (UCATS) instruments), O3 (measured in situ by the NOAA dual-beam ultraviolet (UV) photometer), NO2, BrO (remotely detected by spectroscopic UV-visible (UV-vis) limb observations; see the companion paper of Stutz et al., 2016), and of some key brominated source gases in whole-air samples of the Global Hawk Whole Air Sampler (GWAS) instrument within the subtropical lowermost stratosphere (LS) and the tropical upper troposphere (UT) and tropopause layer (TTL). The measurements were performed within the framework of the NASA-ATTREX (National Aeronautics and Space Administration - Airborne Tropical Tropopause Experiment) project from aboard the Global Hawk (GH) during six deployments over the eastern Pacific in early 2013. These measurements are compared with TOMCAT/SLIMCAT (Toulouse Off-line Model of Chemistry And Transport/Single Layer Isentropic Model of Chemistry And Transport) 3-D model simulations, aiming at improvements of our understanding of the bromine budget and photochemistry in the LS, UT, and TTL.Changes in local O3 (and NO2 and BrO) due to transport processes are separated from photochemical processes in intercomparisons of measured and modeled CH4 and O3. After excellent agreement is achieved among measured and simulated CH4 and O3, measured and modeled [NO2] are found to closely agree with ≤ 15 ppt in the TTL (which is the detection limit) and within a typical range of 70 to 170 ppt in the subtropical LS during the daytime. Measured [BrO] ranges between 3 and 9 ppt in the subtropical LS. In the TTL, [BrO] reaches 0.5 ± 0.5 ppt at the bottom (150 hPa/355 K/14 km) and up to about 5 ppt at the top (70 hPa/425 K/18.5 km; see Fueglistaler et al., 2009 for the definition of the TTL used), in overall good agreement with the model simulations. Depending on the

  11. Degradation of Polymeric Brominated Flame Retardants: Development of an Analytical Approach Using PolyFR and UV Irradiation.

    Science.gov (United States)

    Koch, Christoph; Dundua, Alexander; Aragon-Gomez, Jackelyn; Nachev, Milen; Stephan, Susanne; Willach, Sarah; Ulbricht, Mathias; Schmitz, Oliver J; Schmidt, Torsten C; Sures, Bernd

    2016-12-06

    Many well-established methods for studying the degradation of brominated flame retardants are not useful when working with polymeric and water insoluble species. An example for this specific class of flame retardants is PolyFR (polymeric flame retardant; CAS No 1195978-93-8), which is used as a substituent for hexabromocyclododecane. Although it has been on the market for two years now, almost no information is available about its long time behavior in the environment. Within this study, we focus on how to determine a possible degradation of both pure PolyFR as well as PolyFR in the final insulation product, expanded polystyrene foam. Therefore, we chose UV radiation followed by analyses of the total bromine content at different time points via ICP-MS and identified possible degradation products such as 2,4,6-tribromophenol through LC-MS. These results were then linked with measurements of the adsorbable organically bound bromine and total organic carbon in order to estimate their concentrations. With respect to the obtained (1)H NMR, GPC, and contact angle results, the possibility for further degradation was discussed, as UV irradiation can influence the decomposition of molecules in combination with other environmental factors like biodegradation.

  12. Bromination of Graphene: A New Route to Making High Performance Transparent Conducting Electrodes with Low Optical Losses

    KAUST Repository

    Mansour, Ahmed

    2015-07-22

    The unique optical and electrical properties of graphene have triggered great interest in its application as a transparent conducting electrode material and significant effort has been invested in achieving high conductivity while maintaining transparency. Doping of graphene has been a popular route for reducing its sheet resistance, but this has typically come at a significant cost in optical transmission. We demonstrate doping of few layers graphene with bromine as a means of enhancing the conductivity via intercalation without major optical losses. Our results demonstrate the encapsulation of bromine leads to air-stable transparent conducting electrodes with five-fold improvement of sheet resistance reaching at the cost of only 2-3% loss of optical transmission. The remarkably low tradeoff in optical transparency leads to the highest enhancements in the figure of merit reported thus far for FLG. Furthermore, we tune the workfunction by up to 0.3 eV by tuning the bromine content. These results should help pave the way for further development of graphene as a potential substitute to transparent conducting polymers and metal oxides used in optoelectronics, photovoltaics and beyond.

  13. Brominated flame retardants in the surrounding soil of two manufacturing plants in China: Occurrence, composition profiles and spatial distribution.

    Science.gov (United States)

    Li, Wen-Long; Liu, Li-Yan; Zhang, Zi-Feng; Song, Wei-Wei; Huo, Chun-Yan; Qiao, Li-Na; Ma, Wan-Li; Li, Yi-Fan

    2016-06-01

    Surface soil samples were collected surrounding two brominated flame retardants (BFRs) manufacturing plants in China in August 2014 and analyzed for 23 polybrominated diphenyl ethers (PBDEs) and 8 novel brominated flame retardants (NBFRs). BDE209 and decabromodiphenylethane (DBDPE) were the predominant compounds in soil with the median levels of 1600 and 560 ng/g dw, respectively. The PBDEs profiles in soil samples were consistent with that of commercial product (comDecaBDE). The percentage contributions to total PBDEs decreased from higher to lower brominated homologues. Lower concentrations of NBFRs (excluding DBDPE) were detected in soil surrounding the two plants, suggesting they are byproducts or degradation products of the manufacturing activities. The concentrations of most BFRs dropped exponentially within 3-5 km of the manufacturing plants, suggesting recent deposition of these compounds to the soil. Directional distribution indicated that PBDEs and DBDPE concentrations were highest in the north direction of Plants 1. Three-day air parcel forward trajectories confirmed that the air parcel was responsible for the higher concentration of BFRs in the soil of north direction of the plant.

  14. Brominated flame retardants in food and environmental samples from a production area in China: concentrations and human exposure assessment.

    Science.gov (United States)

    Li, Peng; Wu, Hui; Li, Qiuxu; Jin, Jun; Wang, Ying

    2015-11-01

    Human exposure to brominated flame retardants (BFRs: decabromodiphenyl ether (BDE209), decabromodiphenyl ethane (DBDPE), hexabromobenzene (HBB), pentabromoethylbenzene (PBEB), pentabromotoluene (PBT), 1,2,3,4,5-pentabromobenzene (PBBz), and 2,3,5,6-tetrabromo-p-xylene (TBX)) in a brominated flame retardant production area (Weifang, Shandong Province, China) was estimated. Thirty food samples, 14 air samples, and 13 indoor dust samples were analyzed. BDE209 and DBDPE were the dominant BFRs in all samples. Higher alternative brominated flame retardant (including DBDPE, HBB, PBEB, PBT, PBBz, and TBX) concentrations were found in vegetables than in fish and meat; thus, plant-original foods might be important alternative BFR sources in the study area. The BDE209 and alternative BFR concentrations in air were 1.5×10(4) to 2.2×10(5) and 620 to 3.6×10(4) pg/m3, respectively. Mean total BFR exposures through the diet, inhalation, and indoor dust ingestion were 570, 3000, and 69 ng/d, respectively (16, 82, and 2% of total intake, respectively). Inhalation was the dominant BFR source except for DBDPE, for which diet dominated. BDE209 contributed 85% of the total BFR intake in the study area.

  15. Impact of biogenic very short-lived bromine on the Antarctic ozone hole during the 21st century

    Science.gov (United States)

    Fernandez, Rafael P.; Kinnison, Douglas E.; Lamarque, Jean-Francois; Tilmes, Simone; Saiz-Lopez, Alfonso

    2017-02-01

    Active bromine released from the photochemical decomposition of biogenic very short-lived bromocarbons (VSLBr) enhances stratospheric ozone depletion. Based on a dual set of 1960-2100 coupled chemistry-climate simulations (i.e. with and without VSLBr), we show that the maximum Antarctic ozone hole depletion increases by up to 14 % when natural VSLBr are considered, which is in better agreement with ozone observations. The impact of the additional 5 pptv VSLBr on Antarctic ozone is most evident in the periphery of the ozone hole, producing an expansion of the ozone hole area of ˜ 5 million km2, which is equivalent in magnitude to the recently estimated Antarctic ozone healing due to the implementation of the Montreal Protocol. We find that the inclusion of VSLBr in CAM-Chem (Community Atmosphere Model with Chemistry, version 4.0) does not introduce a significant delay of the modelled ozone return date to 1980 October levels, but instead affects the depth and duration of the simulated ozone hole. Our analysis further shows that total bromine-catalysed ozone destruction in the lower stratosphere surpasses that of chlorine by the year 2070 and indicates that natural VSLBr chemistry would dominate Antarctic ozone seasonality before the end of the 21st century. This work suggests a large influence of biogenic bromine on the future Antarctic ozone layer.

  16. Local Structural and Electronic Changes Associated with the Bromination of YBCO: Charge Transfer and Cu-O Distortions

    Science.gov (United States)

    Dieng, Lamine M.; Tyson, Trevor A.; Croft, M.; Dogan, F.; Woicik, Joseph; Grow, James

    2000-03-01

    In order to understand the role of bromination in the recovery of superconductivity and metallic transport in underdoped YBCO, we have measured the local structural changes in brominated single crystal samples and compared them with normal samples. From the c-axis polarized near edge x-ray absorption measurements, we see, for the first time, direct evidence for the transfer of hole density into the Cu(2)O2 planes in brominated samples. The corresponding XAFS measurements show large changes in the c-axis Cu-O bond distribution. Measurements of the local structure about Ba and Br were also performed. No evidence was found for the incorporation of Br onto the O(4) sites as previously suggested by some authors. We were able to model the coordination of Br and found it to be consistent with BaBr2 as suggested by Fukuda et al. [1] and Potrepka et al. [2]. This work is supported by National Science Foundation Career Grant DMR-9733862. [1] Y. Fukuda et al. Phys. Rev. B 47, 418 (1993). [2] D. M. Potrepka et al., Phys. Rev. B 60, 10489 (1999).

  17. Formation potentials of bromate and brominated disinfection by-products in bromide-containing water by ozonation.

    Science.gov (United States)

    Lin, Tao; Wu, Shouke; Chen, Wei

    2014-12-01

    The ozonation involved in drinking water treatment raises issues of water quality security when the raw water contains bromide (Br(-)). Br(-) ions may be converted to bromate (BrO3 (-)) during ozonation and some brominated disinfection by-products (Br-DBPs) in the following chlorination. In this study, the effects of ozone (O3) dosage, contact time, pH, and Br(-) and ammonia (NH3-N) concentrations on the formation of BrO3 (-) and Br-DBPs have been investigated. The results show that decreasing the initial Br(-) concentration is an effective means of controlling the formation of BrO3 (-). When the concentration of Br(-) was lower than 100 μg/L, by keeping the ratio of O3 dosage to dissolved organic carbon (DOC) concentration at less than 1, BrO3 (-) production was effectively suppressed. The concentration of BrO3 (-) steadily increased with increasing O3 dosage at high Br(-) concentration (>900 μg/L). Additionally, a longer ozonation time increased the concentrations of BrO3 (-) and total organic bromine (TOBr), while it had less impact on the formation potentials of brominated trihalomethanes (Br-THMFP) and haloacetic acids (Br-HAAFP). Higher pH value and the presence of ammonia may lead to an increase in the formation potential of BrO3 (-) and Br-DBPs.

  18. Hazards of lithium thionyl chloride batteries

    Science.gov (United States)

    Parry, J. M.

    1978-01-01

    Two different topics which only relate in that they are pertinent to lithium thionyl chloride battery safety are discussed. The first topic is a hazards analysis of a system (risk assessment), a formal approach that is used in nuclear engineering, predicting oil spills, etc. It is a formalized approach for obtaining assessment of the degree of risk associated with the use of any particular system. The second topic is a small piece of chemistry related to the explosions that can occur with lithium thionyl chloride systems. After the two topics are presented, a discussion is generated among the Workshop participants.

  19. EVALUATION OF BACTERICIDAL EFFECTIVENESS OF BENZALKONIUM CHLORIDE

    Directory of Open Access Journals (Sweden)

    K. Imandel

    1996-06-01

    Full Text Available Benzalkonium chloride is a quaternary ammounium Compounds derivative under different names such as Afxhang, Hamoon, Mahan etc, which have great and expanded use in sanitation and medical affairs. Bactericidal activity of these disinfectants was fulfilled according to National Standard Method No.2842 on Staph. Aureus, Sal. Typhimouium and E. coli. This laboratory test showed that, except Mahan that has not bactericidal efficacy on E.coli at concentration 0.4 percent, other disinfectants under the study in concentrations of 0.4, 0.8, 1, 1.2 percent have reliable antibacterial properties, and bacterial resistance to benzalkonium chloride has not occurred yet.

  20. Cesium chloride-induced torsades de pointes.

    Science.gov (United States)

    Wiens, Matthew; Gordon, Wendy; Baulcomb, Daisy; Mattman, Andre; Mock, Tom; Brown, Robert

    2009-09-01

    The chloride salt of cesium, a group 1A element, is gaining popularity as an alternative treatment of advanced cancers. Cesium chloride has primarily been used in cardiovascular research for arrhythmogenesis in animals because of its potassium-blocking effects. The present report describes a 45-year-old woman with metastatic breast cancer who experienced repeated episodes of torsades de pointes polymorphic ventricular tachycardia after several months of oral cesium therapy. There was a clear temporal relationship between cesium ingestion and the arrhythmia, which later resolved following discontinuation of cesium therapy. Serial cesium plasma and whole blood levels were measured over the ensuing six months and pharmacokinetic analysis was performed.

  1. Theoretical study of the reaction kinetics of atomic bromine with tetrahydropyran

    KAUST Repository

    Giri, Binod

    2015-02-12

    A detailed theoretical analysis of the reaction of atomic bromine with tetrahydropyran (THP, C5H10O) was performed using several ab initio methods and statistical rate theory calculations. Initial geometries of all species involved in the potential energy surface of the title reaction were obtained at the B3LYP/cc-pVTZ level of theory. These molecular geometries were reoptimized using three different meta-generalized gradient approximation (meta-GGA) functionals. Single-point energies of the stationary points were obtained by employing the coupled-cluster with single and double excitations (CCSD) and fourth-order Møller-Plesset (MP4 SDQ) levels of theory. The computed CCSD and MP4(SDQ) energies for optimized structures at various DFT functionals were found to be consistent within 2 kJ mol-1. For a more accurate energetic description, single-point calculations at the CCSD(T)/CBS level of theory were performed for the minimum structures and transition states optimized at the B3LYP/cc-pVTZ level of theory. Similar to other ether + Br reactions, it was found that the tetrahydropyran + Br reaction proceeds in an overall endothermic addition-elimination mechanism via a number of intermediates. However, the reactivity of various ethers with atomic bromine was found to vary substantially. In contrast with the 1,4-dioxane + Br reaction, the chair form of the addition complex (c-C5H10O-Br) for THP + Br does not need to undergo ring inversion to form a boat conformer (b-C4H8O2-Br) before the intramolecular H-shift can occur to eventually release HBr. Instead, a direct, yet more favorable route was mapped out on the potential energy surface of the THP + Br reaction. The rate coefficients for all relevant steps involved in the reaction mechanism were computed using the energetics of coupled cluster calculations. On the basis of the results of the CCSD(T)/CBS//B3LYP/cc-pVTZ level of theory, the calculated overall rate coefficients can be expressed as kov.,calc.(T) = 4.60 × 10

  2. Measurement-based modeling of bromine-induced oxidation of mercury above the Dead Sea

    Science.gov (United States)

    Tas, E.; Obrist, D.; Peleg, M.; Matveev, V.; Faïn, X.; Asaf, D.; Luria, M.

    2011-08-01

    Atmospheric mercury depletion events (AMDEs) outside the polar regions - driven by high levels of reactive bromine species (RBS) - were observed recently in the warm Dead Sea boundary layer. Efficient oxidation of gaseous elemental mercury (GEM) under temperate conditions by RBS was unexpected considering that the thermal back dissociation reaction of HgBr, a proposed key mechanism, is more than 2.5 orders of magnitude higher under Dead Sea temperatures compared with polar temperatures. The goal of this study was to improve understanding of RBS-mercury interactions using numerical simulations based on a comprehensive measurement campaign performed at the Dead Sea during summer 2009. Results demonstrate a high efficiency and central role of BrOx (i.e., Br + BrO) for AMDEs at the Dead Sea, with relative contributions for GEM depletion of more than ~90 %. BrO was found to be the dominant oxidant with relative contribution above 80 %. Best agreement between simulations and observations was achieved by applying rate constants for kHg+Br and kHg+BrO of 2.7×10-13 cm3 molecule-1 s-1 and 1.5 × 10-13 cm3 molecule-1 s-1, respectively - indicating that kHg+BrO is higher than most reported values and that BrO is a more efficient oxidant than Br in the ozone-rich atmosphere (i.e., for [BrO]/[Br] >2). This further explains why the efficiency of GEM oxidation by reactive bromine species at the Dead Sea doesn't critically depend on Br and, therefore, is comparable to the efficiency in polar regions even under much higher temperatures. These findings also support the hypothesis identified in a previous study, that Br-induced GEM depletion can be important above oceans in the mid-latitudes and tropics. In the presence of anthropogenic NO2, RBS activity can lead to enhanced NO3 formation, which then causes significant nighttime GEM depletion.

  3. Modelling the impact of chlorine and bromine emissions from large Plinian eruptions on ozone

    Science.gov (United States)

    Brenna, Hans; Krüger, Kirstin; Kutterolf, Steffen

    2016-04-01

    Large Plinian volcanic eruptions inject large amounts of atmosphere-relevant gases (e.g. S, Cl, Br) and materials into the stratosphere. If the eruption occurs in the tropics, it can have a global impact due to the dispersal through the large scale meridional overturning circulation. Most climate model studies concentrate on the sulfate aerosol effects on climate. In contrast, ozone-depletion initiated by volcanic halogens from tropical eruptions was believed to play an insignificant role for the global atmosphere, based on observations from the recent El Chichon and Pinatubo eruptions. New results regarding the halogen release by Plinian eruptions, as well as recent volcanic plume observations and model simulations facilitate now our investigation into what effect the combined chlorine and bromine emissions from large tropical eruptions have on ozone and the atmosphere in general. A complete halogen data set for the last 200 ka (Kutterolf et al., 2015), derived by the petrological method from paleo-eruptions of the Central American Volcanic Arc (CAVA), are used to force simulations with the advanced chemistry climate model WACCM (Whole Atmosphere Community Climate Model). The goal is to quantify the impact of volcanic halogens on the preindustrial atmosphere when the background chlorine levels were low compared to the present day with the main focus on stratospheric ozone. We carried out 5 model simulations assuming that 10% of the Cl and Br (9.51e+6 kg Br and 2.93e+9 kg Cl) emitted from the average CAVA eruption is injected into the tropical stratosphere during January. The model response reveals a global impact on the ozone layer affecting via radiation also atmospheric dynamics for more than 5 years. Given the current decline in anthropogenic chlorine, the results will become relevant for future halogen-rich explosive eruptions in the tropics. References: Kutterolf, S., T. Hansteen, A. Freundt, H. Wehrmann, K. Appel, K. Krüger, and W. Pérez (2015), Bromine

  4. Development of Zinc/Bromine Batteries for Load-Leveling Applications: Phase 1 Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Eidler, Phillip

    1999-07-01

    The Zinc/Bromine Load-Leveling Battery Development contract (No. 40-8965) was partitioned at the outset into two phases of equal length. Phase 1 started in September 1990 and continued through December 1991. In Phase 1, zinc/bromine battery technology was to be advanced to the point that it would be clear that the technology was viable and would be an appropriate choice for electric utilities wishing to establish stationary energy-storage facilities. Criteria were established that addressed most of the concerns that had been observed in the previous development efforts. The performances of 8-cell and 100-cell laboratory batteries demonstrated that the criteria were met or exceeded. In Phase 2, 100-kWh batteries will be built and demonstrated, and a conceptual design for a load-leveling plant will be presented. At the same time, work will continue to identify improved assembly techniques and operating conditions. This report details the results of the efforts carried out in Phase 1. The highlights are: (1) Four 1-kWh stacks achieved over 100 cycles, One l-kWh stack achieved over 200 cycles, One 1-kWh stack achieved over 300 cycles; (2) Less than 10% degradation in performance occurred in the four stacks that achieved over 100 cycles; (3) The battery used for the zinc loading investigation exhibited virtually no loss in performance for loadings up to 130 mAh/cm{sup 2}; (4) Charge-current densities of 50 ma/cm{sup 2} have been achieved in minicells; (5) Fourteen consecutive no-strip cycles have been conducted on the stack with 300+ cycles; (6) A mass and energy balance spreadsheet that describes battery operation was completed; (7) Materials research has continued to provide improvements in the electrode, activation layer, and separator; and (8) A battery made of two 50-cell stacks (15 kWh) was produced and delivered to Sandia National Laboratories (SNL) for testing. The most critical development was the ability to assemble a battery stack that remained leak free. The

  5. Temperature dependence of bromine activation due to reaction with ozone in a proxy for organic aerosols

    Science.gov (United States)

    Edebeli, Jacinta; Ammann, Markus; Gilgen, Anina; Eichler, Anja; Schneebeli, Martin; Bartels-Rausch, Thorsten

    2016-04-01

    The discovery of boundary layer ozone depletion events in the Polar Regions [1] and in the mid-latitudes [2], two areas of very different temperature regimes, begs the question of temperature dependence of reactions responsible for these observations [3]. These ODEs have been attributed to ozone reacting with halides leading to reactive halogens (halogen activation) of which bromide is extensively studied, R1 - R3 [4, 5] (R1 is a multiphase reaction). O3 + Br-→ O2 + OBr- (R1) OBr- + H+ ↔ HOBr (R2) HOBr + H+ + Br-→ Br2 + H2O (R3) Despite extensive studies of ozone-bromide interactions, the temperature dependence of bromine activation is not clear [3]. This limits parameterization of the involved reactions and factors in atmospheric models [3, 6]. Viscosity changes in the matrix (such as organic aerosols) due to temperature have been shown to influence heterogeneous reaction rates and products beyond pure temperature effect [7]. With the application of coated wall flow-tubes, the aim of this study is therefore to investigate the temperature dependence of bromine activation by ozone interaction while attempting to characterize the contributions of the bulk and surface reactions to observed ozone uptake. Citric acid is used in this study as a hygroscopically characterized matrix whose viscosity changes with temperature and humidity. Here, we present reactive ozone uptake measured between 258 and 289 K. The data show high reproducibility. Comparison of measured uptake with modelled bulk uptake at different matrix compositions (and viscosities) indicate that bulk reactive uptake dominates, but there are other factors which still need further consideration in the model. References 1. Barrie, L.A., et al., Nature, 1988. 334: p. 138 - 141. 2. Hebestreit, K., et al., Science, 1999. 283: p. 55-57. 3. Simpson, W.R., et al., Atmospheric Chemistry and Physics, 2007. 7: p. 4375 - 4418. 4. Haag, R.W. and J. Hoigné, Environ Sci Technol, 1983. 17: p. 261-267. 5. Oum, K.W., et

  6. Measurement-based modeling of bromine-induced oxidation of mercury above the Dead Sea

    Directory of Open Access Journals (Sweden)

    E. Tas

    2011-08-01

    Full Text Available Atmospheric mercury depletion events (AMDEs outside the polar regions – driven by high levels of reactive bromine species (RBS – were observed recently in the warm Dead Sea boundary layer. Efficient oxidation of gaseous elemental mercury (GEM under temperate conditions by RBS was unexpected considering that the thermal back dissociation reaction of HgBr, a proposed key mechanism, is more than 2.5 orders of magnitude higher under Dead Sea temperatures compared with polar temperatures. The goal of this study was to improve understanding of RBS-mercury interactions using numerical simulations based on a comprehensive measurement campaign performed at the Dead Sea during summer 2009.

    Results demonstrate a high efficiency and central role of BrOx (i.e., Br + BrO for AMDEs at the Dead Sea, with relative contributions for GEM depletion of more than ~90 %. BrO was found to be the dominant oxidant with relative contribution above 80 %. Best agreement between simulations and observations was achieved by applying rate constants for kHg+Br and kHg+BrO of 2.7×10−13 cm3 molecule−1 s−1 and 1.5 × 10−13 cm3 molecule−1 s−1, respectively – indicating that kHg+BrO is higher than most reported values and that BrO is a more efficient oxidant than Br in the ozone-rich atmosphere (i.e., for [BrO]/[Br] >2. This further explains why the efficiency of GEM oxidation by reactive bromine species at the Dead Sea doesn't critically depend on Br and, therefore, is comparable to the efficiency in polar regions even under much higher temperatures. These findings also support the hypothesis identified in a previous study, that Br-induced GEM depletion can be important above oceans in the mid-latitudes and tropics. In the presence of anthropogenic NO2, RBS activity can lead to enhanced NO3

  7. Brominated flame retardants in the Arctic. An overview of spatial and temporal trends

    Energy Technology Data Exchange (ETDEWEB)

    Wit, C. de [Institute of Applied Environmental Research, Stockholm (Sweden); Alaee, M.; Muir, D. [National Water Research Institute, Burlington, MA (United States)

    2004-09-15

    The Stockholm Convention on Persistent Organic Pollutants (POPs), which entered into force on May 17, 2004, includes wording that chemicals with the characteristics of POPs are those found in locations ''distant from sources'' and those for which ''monitoring data showing that long-range environmental transport of the chemical may have occurred''. Thus, the Arctic has become an important indicator region for assessment of persistence and bioaccumulation. The Arctic environment is well suited as a region in which to evaluate POPs. Some regions of thee Arctic, particularly the Barents Sea area north of Norway and western Russia are relatively close to source regions of POPs. Cold conditions favor persistence of POPs relative to temperate or tropical environments. The presence of fourth level carnivores (e.g. polar bears and seabirds), and storage of lipid as an energy source, make Arctic food webs vulnerable to bioaccumulative chemicals. Indigenous people in the Arctic utilizing a traditional diet, which is high in nutritionally beneficial fat, results in their elevated exposure to some POPs. The first indication that brominated flame retardants (BFRs) were reaching the Arctic was the detection by Jansson et al. of lower molecular weight polybrominated diphenyl ethers (PBDEs) in Svalbard Brunnichfs guillemots (130 ng/g lipid weight) and ringed seals (40 ng/g lw) collected in 1981. Whitefish collected from Lake Storvindeln in 1986, a pristine mountain lake in the Swedish mountains near Ammarnas, had {sigma}PBDE levels of 26 ng/g lw. Despite these early findings, only recently have the spatial and temporal trends of BFRs been studied in detail in the Arctic. The purpose of this paper is to review the new data on BFRs in the Arctic and assess whether this information supports the view that PBDEs and other BFRs of similar molecular weight are POPs and potential global pollutants. This review is based on a recent assessment of POPs

  8. Synoptic-scale meteorological control on reactive bromine production and ozone depletion in the Arctic boundary layer: 3-D simulation with the GEM-AQ model

    Directory of Open Access Journals (Sweden)

    K. Toyota

    2010-11-01

    Full Text Available Episodes of high bromine levels and surface ozone depletion in the springtime Arctic are simulated by an online air-quality model, GEM-AQ, with gas-phase and heterogeneous reactions of inorganic bromine species and a simple scheme of air-snowpack chemical interactions implemented for this study. Snowpack on sea ice is assumed to be the only source of bromine to the atmosphere and capable of converting relatively stable bromine species to photolabile Br2 via air-snowpack interactions. A "bromine explosion", by which Br retained in the snowpack is autocatalytically released to the atmosphere as a result of dry deposition of HOBr and BrONO2, is assumed to occur on young, first-year (FY sea ice (or its overlying snowpack, whereas the snowpack on old, multi-year (MY sea ice and over land is assumed only to recycle a part (but up to 100% of bromine reservoirs lost via dry deposition back to Br2. Model runs are performed for April 2001 at a horizontal resolution of approximately 100 km × 100 km in the Arctic. The model simulates temporal variations in surface ozone mixing ratios as observed at stations in the high Arctic and the synoptic-scale evolution of enhanced BrO column amounts ("BrO clouds" as seen from satellite reasonably well. The results strongly suggest: (1 a ubiquitous source of reactive bromine exists on the FY sea ice during the Arctic springtime; and (2 the timing of bromine release to the atmosphere is largely controlled by meteorological forcing on the transport of ozone to the near-surface air. Also, if the surface snowpack supplies most of the reactive bromine in the Arctic boundary layer, it should be capable of releasing reactive bromine at temperatures as high as −10 °C, particularly on the FY sea ice in the central and eastern Arctic Ocean. Dynamically-induced BrO column variability in the lowermost stratosphere appears to interfere with the use of satellite BrO column

  9. Solvothermal synthesis of strontium phosphate chloride nanowire

    Science.gov (United States)

    Lam, W. M.; Wong, C. T.; Li, Z. Y.; Luk, K. D. K.; Chan, W. K.; Yang, C.; Chiu, K. Y.; Xu, B.; Lu, W. W.

    2007-08-01

    Strontium phosphate chloride nanowire was synthesized via a solvothermal treatment of strontium tri-polyphosphate and Collin salt in 1,4-dioxane at 150 °C. The effects of 1,4-dioxane concentration on particle morphology, crystallinity and phase purity were investigated in this study. The specimen morphology was analyzed by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). When the concentration of 1,4-dioxane was below 10%, micron-sized whisker was the dominant form. At 20-25% concentration of 1,4-dioxane, strontium phosphate chloride single-crystalline nanowire was 31±12 nm in diameter and 1.43±0.6 μm in length with an aspect ratio of 52.28±29.41. X-ray diffraction (XRD) pattern of this nanowire matched with that of strontium phosphate chloride (JCPDS #083-0973). When 1,4-dioxane concentration exceeded 25%, nanorod aggregate was the dominant form instead of nanowire. At 20-25% 1,4-dioxane concentration suitable strontium concentration combine with high chemical potential environment favors the formation of nanowires. By adding 1,4-dioxane impure phase such as β-strontium hydrogen phosphate, nanorod formation was suppressed. This method provides an efficient way to synthesize high aspect ratio strontium phosphate chloride nanowire. It has potential bioactive nanocomposite, high mechanical performance bioactive bone cement filler and fluorescent material applications.

  10. Controlling chloride ions diffusion in concrete.

    Science.gov (United States)

    Zeng, Lunwu; Song, Runxia

    2013-11-28

    The corrosion of steel in concrete is mainly due to the chemical reaction between the chloride ions and iron ions. Indeed, this is a serious threaten for reinforced concrete structure, especially for the reinforced concrete structure in the sea. So it is urgent and important to protect concrete against chloride ions corrosion. In this work, we report multilayer concrete can cloak chloride ions. We formulated five kinds of concrete A, B, C, D and E, which are made of different proportion of cement, sand and glue, and fabricated six-layer (ABACAD) cylinder diffusion cloak and background media E. The simulation results show that the six-layer mass diffusion cloak can protect concrete against chloride ions penetration, while the experiment results show that the concentration gradients are parallel and equal outside the outer circle in the diffusion flux lines, the iso-concentration lines are parallel outside the outer circle, and the concentration gradients in the inner circle are smaller than those outside the outer circle.

  11. Influence of compaction on chloride ingress

    NARCIS (Netherlands)

    Zlopasa, J.

    2012-01-01

    Experiences from practice show the need for more of an understanding and optimization of the compaction process in order to design a more durable concrete structure. Local variations in compaction are very often the reason for initiation of local damage and initiation of chloride induced corrosion.

  12. Liquid crystalline critical dynamics in decylammonium chloride

    CERN Document Server

    Lee, K W; Lee, C E; Kang, K H; Rhee, C; Kang, J K

    1999-01-01

    Collective chain dynamics and phase transitions in a model biomembrane, decylammonium chloride (C sub 1 sub 0 H sub 2 sub 1 NH sub 3 Cl), were studied by means of proton nuclear magnetic resonance. Our measurements sensitively reflect the critical dynamics associated with the smectic C to smectic A transition of the lipid bilayer.

  13. Chloride migration in concrete with superabsorbent polymers

    DEFF Research Database (Denmark)

    Hasholt, Marianne Tange; Jensen, Ole Mejlhede

    2015-01-01

    Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete mixt...

  14. Gebromeerde vlamvertragers en broomdioxines in Choline Chloride

    NARCIS (Netherlands)

    Egmond, van H.J.; Traag, W.A.; Hoogenboom, L.A.P.

    2008-01-01

    Sinds begin 2008 worden in het Nationaal Plan Diervoeder Choline Chloride monsters (= diervoeder additief) gevonden waarbij de DR CALUX screenings-assay een sterk verdacht signaal geeft, maar bij de GC-HRMS geen dioxines en dl-PCB's worden gevonden. Dit rapport beschrijft de resultaten van nader ond

  15. Amperometric Sensor for Detection of Chloride Ions

    Directory of Open Access Journals (Sweden)

    Rene Kizek

    2008-09-01

    Full Text Available Chloride ion sensing is important in many fields such as clinical diagnosis, environmental monitoring and industrial applications. We have measured chloride ions at a carbon paste electrode (CPE and at a CPE modified with solid AgNO3, a solution of AgNO3 and/or solid silver particles. Detection limits (3 S/N for chloride ions were 100 μM, 100 μM and 10 μM for solid AgNO3, solution of AgNO3 and/or solid silver particles, respectively. The CPE modified with silver particles is the most sensitive to the presence chloride ions. After that we approached to the miniaturization of the whole electrochemical instrument. Measurements were carried out on miniaturized instrument consisting of a potentiostat with dimensions 35 × 166 × 125 mm, screen printed electrodes, a peristaltic pump and a PC with control software. Under the most suitable experimental conditions (Britton-Robinson buffer, pH 1.8 and working electrode potential 550 mV we estimated the limit of detection (3 S/N as 500 nM.

  16. Regulated trafficking of the CFTR chloride channel

    NARCIS (Netherlands)

    Braakman, L.J.; Kleizen, B.; Jonge, H.R. de

    2000-01-01

    The cystic fibrosis transmembrane conductance regulator (CFTR), the ABC transporter encoded by the cystic fibrosis gene, is localized in the apical membrane of epithelial cells where it functions as a cyclic AMP-regulated chloride channel and as a regulator of other ion channels and transporters. Wh

  17. 21 CFR 582.3845 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Stannous chloride. 582.3845 Section 582.3845 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  18. 29 CFR 1910.1017 - Vinyl chloride.

    Science.gov (United States)

    2010-07-01

    ... possible exposure conditions. (2) Protective garments shall be provided clean and dry for each use. (i... Required Authorized Personnel Only (3) Containers of polyvinyl chloride resin waste from reactors or other... which may be useful: A. For kidney dysfunction: urine examination for albumin, red blood cells,...

  19. Assessing oestrogenic effects of brominated flame retardants hexabromocyclododecane and tetrabromobisphenol A on MCF-7 cells.

    Science.gov (United States)

    Dorosh, A; Děd, L; Elzeinová, F; Pěknicová, J

    2011-01-01

    Tetrabromobisphenol A (TBBPA) is the main flame retardant used in printed circuit boards and laminates. The human population is highly exposed to TBBPA as it is used in consumer electronics as well as office and communication equipment. The main use of hexabromocyclododecane (HBCD) is in insulation foam boards, which are widely used in the construction sector. Brominated flame retardants may possess endocrine disrupting activity and thus represent a threat to the environment, including humans and their reproduction. The aim of this work was to evaluate the oestrogenic effects of TBBPA and HBCD in vitro on MCF-7 cells. We used the proliferation test (E-screen assay) in MCF-7 breast cancer cells and reverse transcription quantitative polymerase chain reaction analysis of TFF1 gene expression to analyse oestrogenicity of the studied compounds. RT-qPCR has proved to be a fast and valuable molecular technique in gene expression quantification. HBCD but not TBBPA increased cell proliferation in MCF-7 cells and up-regulated TFF1 gene expression in a concentration-dependent manner. Anti-oestrogen ICI 182,780 inhibited up-regulation of TFF1 by HBCD. We have shown that HBCD displays oestrogen- like effects on MCF-7 cells. TBBPA, on the other hand, has not shown any oestrogenic effect mediated by the oestrogen receptor α.

  20. Crystal structure of a photobiologically active brominated angular pyranocoumarin: bromo-hydroxy-seselin

    Directory of Open Access Journals (Sweden)

    A. K. Bauri

    2017-03-01

    Full Text Available The title compound, C14H13BrO3 [systematic name: rac-(9S,10R-9-bromo-10-hydroxy-8,8-dimethyl-9,10-dihydro-2H,8H-pyrano[2,3-f]chromen-2-one], is a substituted pyranocoumarin, obtained by bromination of seselin [8,8-dimethyl-2H,8H-pyrano[2,3-f]chromen-2-one], which was isolated from the Indian herb Trachyspermum stictocarpum (Aajmod. The pyrano ring has a distorted half-chair conformation and its mean plane is inclined to the coumarin mean plane by 1.6 (2°. In the crystal, molecules are linked by pairs of O—H...O hydrogen bonds, forming inversion dimers with an R22(16 ring motif. The dimers stack along the a-axis direction and are linked by offset π–π interactions, forming columns [intercentroid distance = 3.514 (4 Å].

  1. In vitro screening of the endocrine disrupting potency of brominated flame retardants and their metabolites

    Energy Technology Data Exchange (ETDEWEB)

    Hamers, T.; Kamstra, J.H. [Inst. for Environmental Studies (IVM), Amsterdam (Netherlands); Sonneveld, E. [BioDetection Systems (BDS), Amsterdam (Netherlands); Murk, A.J. [Wageningen Univ., Toxicology Group, Wageningen (Netherlands); Zegers, B.N.; Boon, J.P. [Royal Netherlands Inst. for Sea Research (NIOZ), Den Burg (Netherlands); Brouwer, A. [Umea Univ., Umea (Sweden)

    2004-09-15

    Substantial evidence is recently becoming available that brominated flame retardants (BFRs) are potential endocrine disruptors. The toxicological profile of BFRs, however, is too incomplete and insufficient to perform human and ecological risk assessment. To fill these gaps, the EU funded research program FIRE was started in December 2002. This program aims at the identification and toxicological characterization of the most potent and environmentally relevant BFRs and their possible risk for human and wildlife health. As part of a hazard identification approach, twenty seven BFRs have been selected within the framework of FIRE for pre-screening their endocrinedisrupting potencies. Selection of test compounds was based on a maximal variation in physicochemical characteristics of BFRs within the test set, allowing the establishment of quantitative structure-activity relationships (QSARs). In addition, environmental relevance (e.g. high production volumes and persistence) and availability for testing were used as selection criteria. BFRs were tested in seven different in vitro bioassays for their potency to interfere via estrogenic, thyroidal, androgenic, progestagenic, and Ah-receptor mediated pathways. Metabolisation rates of BFRs were determined using phenobarbital-induced rat liver microsomes. Finally, the endocrine disrupting potency of the metabolites was determined in the same in vitro bio-assays and compared to the potency of the parent compounds.

  2. A study of the presence of brominated flame retardants in Australian fauna

    Energy Technology Data Exchange (ETDEWEB)

    Symons, R.; Burniston, D.; Piro, N.; Stevenson, G.; Yates, A. [Australian Government Analytical Laboratories, Sydney (Australia)

    2004-09-15

    Brominated flame retardants, in particular polybrominated diphenyl ethers (PBDEs) gained prominence in the late nineties when Noren et al. reported an exponential increase in PBDE levels found in Swedish mothers milk over a quarter of a century period with an associated decrease in levels of dioxin-like compounds. PBDEs have since become exceptionally widely studied being detected in most environmental compartments and food as well as human tissues. Only limited information on the distribution if PBDEs is available for the Southern Hemisphere, however, elevated levels of PBDEs in pork fat were detected during the routine screening for organochlorine pesticide residues. More recently an investigation of breast milk for PBDE levels also demonstrated that levels were comparable with those in the Northern Hemisphere. BFRs are not manufactured in Australia but it has been estimated that over 500 tonnes are imported yearly of which 340 tonnes are PBDEs. In addition, the amount of PBDEs that are contained in imported articles used both in domestic and industrial applications is unknown. In this paper, we report levels of PBDEs in a range of different Australian fauna that show that these POPs have indeed become widely distributed both in terms of the types of the fauna but also the levels determined.

  3. Persistent brominated and chlorinated dioxin blood levels in a chemist. 35 years after dioxin exposure

    Energy Technology Data Exchange (ETDEWEB)

    Schecter, A.; Ryan, J.J. (Department of Preventive Medicine, College of Medicine, SUNY Health Science Center-Syracuse, NY (United States))

    1992-07-01

    This is the first report on occupational health hazards to dioxin chemists associated with laboratory exposure to 2,3,7,8-tetrabromodibenzodioxin (TBrDD), and further characterizes the human response to 2,3,7,8 tetrachlorodibenzodioxin (TCDD). In this case study the chemist was exposed on two separate occasions. In March 1956, after synthesizing 10 g of TBrDD, the chemist suffered from mild and transient chloracne of the neck and wrists; in September 1956, after synthesizing 16 g of TCDD, he suffered severe chloracne of the entire body, headaches, backache, and leg pain on exertion. His measured 2,3,7,8-TBrDD in 1991 was 625 parts per trillion (ppt) in whole blood lipid, 35 years after initial exposure and 18 ppt TCDD, an elevated level in comparison with the mean 2,3,7,8-TCDD level of 5 ppt in the US population. This is the first reported detection of a brominated dioxin in human tissue. The total halogenated dioxin body burden in September 1956 is estimated to have been between 13,005 ppt and 146,726 ppt. This amount can be considered to be, at least in this person, a strong chloracnegenic dose, and a dose causing human nervous system and muscular or circulatory system responses. This uptake demonstrates an occupational hazard to chemists and chemical workers, and the usefulness of human tissue dioxin measurements to document absorption.

  4. Brominated diphenyl ether levels. A comparison of tributary sediments versus biosolid material

    Energy Technology Data Exchange (ETDEWEB)

    Kolic, T.M.; MacPherson, K.A.; Reiner, E.J. [Ontario Ministry of the Environment, Laboratory Services Branch, Toronto, ON (Canada); Ho, T.; Kleywegt, S. [Ontario Ministry of the Environment, Standards Development Branch, Toronto, ON (Canada); Dove, A.; Marvin, C. [Environment Canada, Burlington, ON (Canada)

    2004-09-15

    PBDEs are persistent in the environment, have low water solubility and are known to have a tendency to bioaccumulate in wildlife and humans. There are 209 possible PBDE congeners. There has been concern over the bioaccumulation of these compounds since they have been found in mother's milk. Some of the brominated diphenyl ethers are known to metabolize into hydroxylated compounds and these metabolites are known to compete with and reduce thyroxine (T4) from binding to the thyroxine binding protein, transthyretin. This disrupts the thyroid hormone system interaction that has recently been notable amongst women in the form of hypothyroidism that can affect the fetus development in the form of neurodevelopmental deficits. There have been reports of estrogenic activities regarding PBDEs and their hydroxylated counterparts. Information such as this is indicative that PBDEs are endocrine disruptors. Due to their lipophilic nature, PBDEs have a high binding affinity to particulates and accumulate in sediments. Various reports on sediments and sludge type matrices have been reported in Austria, Switzerland, Netherlands and Canada. The following paper is a presentation of levels of PBDEs found in Tributary sediments and their comparison of levels to nearby biosolid sampling locations along Lake Ontario.

  5. QSAR classification models for the prediction of endocrine disrupting activity of brominated flame retardants.

    Science.gov (United States)

    Kovarich, Simona; Papa, Ester; Gramatica, Paola

    2011-06-15

    The identification of potential endocrine disrupting (ED) chemicals is an important task for the scientific community due to their diffusion in the environment; the production and use of such compounds will be strictly regulated through the authorization process of the REACH regulation. To overcome the problem of insufficient experimental data, the quantitative structure-activity relationship (QSAR) approach is applied to predict the ED activity of new chemicals. In the present study QSAR classification models are developed, according to the OECD principles, to predict the ED potency for a class of emerging ubiquitary pollutants, viz. brominated flame retardants (BFRs). Different endpoints related to ED activity (i.e. aryl hydrocarbon receptor agonism and antagonism, estrogen receptor agonism and antagonism, androgen and progesterone receptor antagonism, T4-TTR competition, E2SULT inhibition) are modeled using the k-NN classification method. The best models are selected by maximizing the sensitivity and external predictive ability. We propose simple QSARs (based on few descriptors) characterized by internal stability, good predictive power and with a verified applicability domain. These models are simple tools that are applicable to screen BFRs in relation to their ED activity, and also to design safer alternatives, in agreement with the requirements of REACH regulation at the authorization step.

  6. QSAR modeling and prediction of the endocrine-disrupting potencies of brominated flame retardants.

    Science.gov (United States)

    Papa, Ester; Kovarich, Simona; Gramatica, Paola

    2010-05-17

    In the European Union REACH regulation, the chemicals with particularly harmful behaviors, such as endocrine disruptors (EDs), are subject to authorization, and the identification of safer alternatives to these chemicals is required. In this context, the use of quantitative structure-activity relationships (QSAR) becomes particularly useful to fill the data gap due to the very small number of experimental data available to characterize the environmental and toxicological profiles of new and emerging pollutants with ED behavior such as brominated flame retardants (BFRs). In this study, different QSAR models were developed on different responses of endocrine disruption measured for several BFRs. The multiple linear regression approach was applied to a variety of theoretical molecular descriptors, and the best models, which were identified from all of the possible combinations of the structural variables, were internally validated for their performance using the leave-one-out (Q(LOO)(2) = 73-91%) procedure and scrambling of the responses. External validation was provided, when possible, by splitting the data sets in training and test sets (range of Q(EXT)(2) = 76-90%), which confirmed the predictive ability of the proposed equations. These models, which were developed according to the principles defined by the Organization for Economic Co-operation and Development to improve the regulatory acceptance of QSARs, represent a simple tool for the screening and characterization of BFRs.

  7. From Clothing to Laundry Water: Investigating the Fate of Phthalates, Brominated Flame Retardants, and Organophosphate Esters.

    Science.gov (United States)

    Saini, Amandeep; Thaysen, Clara; Jantunen, Liisa; McQueen, Rachel H; Diamond, Miriam L

    2016-09-01

    The accumulation of phthalate esters, brominated flame retardants (BFRs) and organophosphate esters (OPEs) by clothing from indoor air and transfer via laundering to outdoors were investigated. Over 30 days cotton and polyester fabrics accumulated 3475 and 1950 ng/dm(2) ∑5phthalates, 65 and 78 ng/dm(2) ∑10BFRs, and 1200 and 310 ng/dm(2) ∑8OPEs, respectively. Planar surface area concentrations of OPEs and low molecular weight phthalates were significantly greater in cotton than polyester and similar for BFRs and high molecular weight phthalates. This difference was significantly and inversely correlated with KOW, suggesting greater sorption of polar compounds to polar cotton. Chemical release from cotton and polyester to laundry water was >80% of aliphatic OPEs (log KOW phthalates (log KOW 4-6), and phthalates (log KOW > 8) and BFRs (log KOW > 6). These results support the hypothesis that clothing acts an efficient conveyer of soluble semivolatile organic compounds (SVOCs) from indoors to outdoors through accumulation from air and then release during laundering. Clothes drying could as well contribute to the release of chemicals emitted by electric dryers. The results also have implications for dermal exposure.

  8. Characterization of brominated flame retardants in construction and demolition waste components: HBCD and PBDEs.

    Science.gov (United States)

    Duan, Huabo; Yu, Danfeng; Zuo, Jian; Yang, Bo; Zhang, Yukui; Niu, Yongning

    2016-12-01

    The vast majority of construction material is inert and can be managed as nonhazardous. However, structures may have either been built with some environmentally unfriendly substances such as brominated flame retardants (BFRs), or have absorbed harmful elements such as heavy metals. This study focuses on end-of-life construction materials, i.e. construction and demolition (C&D) waste components. The aim was to characterize the concentration of extremely harmful substances, primarily BFRs, including hexabromocyclododecane (HBCD) and polybrominateddiphenyl ethers (PBDEs). Results revealed extremely high contents of HBCD and PBDEs in typical C&D waste components, particularly polyurethane foam materials. Policies should therefore be developed for the proper management of C&D waste, with priority for POP-containing debris. The first priority is to develop a classification system and procedures to separate out the harmful materials for more extensive processing. Additionally, identification and quantification of the environmental implications associated with dumping-dominated disposal of these wastes are required. Finally, more sustainable materials should be selected for use in the construction industry.

  9. Plasma brominated polymer particles as grafting substrate for thiol-terminated telomers.

    Science.gov (United States)

    Byström, Emil; Nordborg, Anna; Limé, Fredrik; Dinh, Ngoc Phuoc; Irgum, Knut

    2010-06-01

    A combined surface activation and "grafting to" strategy was developed to convert divinylbenzene particles into weak cation exchangers suitable for protein separation. The initial activation step was based on plasma modification with bromoform, which rendered the particles amenable to further reaction with nucleophiles by introducing Br to a surface content of 11.2 atom-%, as determined by X-ray photoelectron spectroscopy. Grafting of thiol-terminated glydicyl methacrylate telomers to freshly plasma activated surfaces was accomplished without the use of added initiator, and the grafting was verified both by reduction in bromine content and the appearance of sulfur-carbon linkages, showing that the surface grafts were covalently bonded. Following grafting the attached glydicyl methacrylate telomer tentacles were further modified by a two-step procedure involving hydrolysis to 2,3-hydroxypropyl groups and conversion of hydroxyl groups to carboxylate functionality by succinic anhydride. The final material was capable of baseline separating four model proteins in 3 min by gradient cation exchange chromatography in a fully aqueous eluent.

  10. [Aqueous iodine solutions as disinfectants: composition, stability, comparison with chlorine and bromine solution (author's transl)].

    Science.gov (United States)

    Gottardi, W

    1978-09-01

    The equilibrium concentrations of aqueous iodine solutions in dependence of the total concentration and the pH-value have been calculated with and without regard of the iodate formation. The values obtained by the latter methode enabled by application of the known rate law to calculate the initial rate of the iodate formation and to draw from this conclusions concerning the stability of iodine solutions. On the grounds of these calculations to aqueous iodine solutions in the concentration and pH-range which is relevant for disinfection (greater than 10(-5) M/l, pH 6--9) one can attribute a stability sufficient for the use in practice and - unlike chlorine and bromine solutions - a content of bactericidal "free halogene" which is higher and independent of the pH-value. The disinfecting action of the iodine cation (H2O+J) which is supposed to be very powerful can be neglected because of its low concentration (10(-3)--10(-6%) of the total concentration). Hypoiodic acid which has already been converted into iodate by disproportionation is as good as lost for the disinfection because of the extremely slow reverse reaction.

  11. Natural Oxidation of Bromide to Bromine in Evaporated Dead Sea Brines

    Science.gov (United States)

    Gavrieli, Ittai; Golan, Rotem; Lazar, Boaz; Baer, Gidi; Zakon, Yevgeni; Ganor, Jiwchar

    2016-04-01

    Highly evaporated Dead Sea brines are found in isolated sinkholes along the Dead Sea. Many of these brines reach densities of over 1.3 kg/L and pHDead Sea brine that drain into the sinkholes. The low pH and the reddish to brownish hue of these brines were an enigma until recently. Despite the rather high total alkalinity (TA) of the Dead Sea (3.826 mmol/kg) the pH of the Dead Sea brine is known to be slightly acidic with a value of ~6.3. In comparison, seawater with the same alkalinity would have a pH value well above 8.3, meaning that H+ activity is 100 fold lower than that of Dead Sea brine. In the present work we assess the apparent dissociation constant value of boric acid (K`B) for the Dead Sea brine and use it to explain the brine's low pH value. We then show that pH decreases further as the brine evaporates and salinity increases. Finally we explain the reddish hue of the hypersaline brines in the sinkholes as due to the presence of dissolved bromine. The latter is the product of oxidation of dissolved bromide, a process that is enabled by the low pH of the hypersaline brines and their high bromide concentration.

  12. Shuttle Environmental Assurance: Brominated Flame Retardants - Concerns, Drivers, Potential Impacts and Mitigation Strategies

    Science.gov (United States)

    Clark-Ingram, Marceia

    2010-01-01

    Brominated Flame Retardants (BFRs) are widely used in the manufacture of electrical and electronic components and as additives in formulations for foams, plastics and rubbers. The United States (US) and the European Union (EU)have increased regulation and monitoring of of targeted BFRs, such as Polybrominated Diphenyl Ethers (PBDEs) due to the bioaccumulative effects in humans and animals. In response, manufacturers and vendors of BFR-containing materials are changing flame-retardant additives, sometimes without notifying BFR users. In some instances, Deca-bromodiphenylether (Deca-BDE) and other families of flame retardants are being used as replacement flame retardants for penta-BDE and octa-BDE. The reformulation of the BFR-containing material typically results in the removal of the targeted PBDE and replacement with a non-PBDE chemical or non-targeted PBDE. Many users of PBDE -based materials are concerned that vendors will perform reformulation and not inform the end user. Materials performance such as flammability, adhesion , and tensile strength may be altered due to reformulation. The requalification of newly formulated materials may be required, or replacement materials may have to be identified and qualified. The Shuttle Enviornmental Assurance (SEA) team indentified a risk to the Space Shuttle Program associated with the possibility that targeted PBDEs may be replaced without notification. Resultant decreases in flame retardancy, Liquid Oxygen (LOX) compatibility, or material performance could have serious consequences.

  13. Simple and rapid quantification of brominated vegetable oil in commercial soft drinks by LC-MS.

    Science.gov (United States)

    Chitranshi, Priyanka; Gamboa da Costa, Gonçalo

    2016-12-15

    We report here a simple and rapid method for the quantification of brominated vegetable oil (BVO) in soft drinks based upon liquid chromatography-electrospray ionization mass spectrometry. Unlike previously reported methods, this novel method does not require hydrolysis, extraction or derivatization steps, but rather a simple "dilute and shoot" sample preparation. The quantification is conducted by mass spectrometry in selected ion recording mode and a single point standard addition procedure. The method was validated in the range of 5-25μg/mL BVO, encompassing the legal limit of 15μg/mL established by the US FDA for fruit-flavored beverages in the US market. The method was characterized by excellent intra- and inter-assay accuracy (97.3-103.4%) and very low imprecision [0.5-3.6% (RSD)]. The direct nature of the quantification, simplicity, and excellent statistical performance of this methodology constitute clear advantages in relation to previously published methods for the analysis of BVO in soft drinks.

  14. Brominated flame retardants (BFRs): A review on environmental contamination in China.

    Science.gov (United States)

    Yu, Gang; Bu, Qingwei; Cao, Zhiguo; Du, Xinming; Xia, Jing; Wu, Min; Huang, Jun

    2016-05-01

    Brominated flame retardants (BFRs) which were detected extensively in environmental and biota samples worldwide, have raised significant concerns during past decades for their persistence, bioaccumulation and potential toxicity to ecological environment and human health. In this paper, we have compiled and reviewed existing literature on the contamination status of BFRs in abiotic and biotic environments in China, including polybrominated diphenyl ethers (PBDEs), hexabromocyclododecane, tetrabromobisphenol A and new BFRs. Temporal trends were also summarized and evaluated. Based on this review, it has been concluded that (1) high concentrations of PBDEs were generally related to the e-waste disposal processing, while the spatial distribution pattern of other BFRs was not necessarily in accordance with this; (2) extremely high concentrations of BFRs in indoor dust emphasized the importance of indoor contamination to human body burdens, while more work need to be done to confirm its contribution; (3) PBDEs in electronics dismantling workers were higher compared to the general population, indicating the occupational exposure should be of particular concern; (4) more data are now becoming available for BFRs in aquatic and terrestrial organisms not previously studied, while studies that consider the occurrence of BFRs in organisms of different trophic levels are still of urgent need for evaluating the fate of BFRs in the food web; and (5) limited data showed a decreasing trend for PBDEs, while more data on time trends of BFR contamination in various matrices and locations are still needed before the impact of regulation of BFRs can be assessed.

  15. Soil contamination by brominated flame retardants in open waste dumping sites in Asian developing countries.

    Science.gov (United States)

    Eguchi, Akifimi; Isobe, Tomohiko; Ramu, Karri; Tue, Nguyen Minh; Sudaryanto, Agus; Devanathan, Gnanasekaran; Viet, Pham Hung; Tana, Rouch Seang; Takahashi, Shin; Subramanian, Annamalai; Tanabe, Shinsuke

    2013-03-01

    In Asian developing countries, large amounts of municipal wastes are dumped into open dumping sites each day without adequate management. This practice may cause several adverse environmental consequences and increase health risks to local communities. These dumping sites are contaminated with many chemicals including brominated flame retardants (BFRs) such as polybrominated diphenyl ethers (PBDEs) and hexabromocyclododecanes (HBCDs). BFRs may be released into the environment through production processes and through the disposal of plastics and electronic wastes that contain them. The purpose of this study was to elucidate the status of BFR pollution in municipal waste dumping sites in Asian developing countries. Soil samples were collected from six open waste dumping sites and five reference sites in Cambodia, India, Indonesia, Malaysia, and Vietnam from 1999 to 2007. The results suggest that PBDEs are the dominant contaminants in the dumping sites in Asian developing countries, whereas HBCD contamination remains low. Concentrations of PBDEs and HBCDs ranged from ND to 180 μg/kg dry wt and ND to 1.4 μg/kg dry wt, respectively, in the reference sites and from 0.20 to 430 μg/kg dry wt and ND to 2.5 μg/kg dry wt, respectively, in the dumping sites. Contamination levels of PBDEs in Asian municipal dumping sites were comparable with those reported from electronic waste dismantling areas in Pearl River delta, China.

  16. Spatial variability of chloride in concrete within homogeneously exposed areas

    NARCIS (Netherlands)

    Angst, U.M.; Polder, R.B.

    2014-01-01

    The concept of variability is increasingly considered in service life predictions. This paper reports experimental data on the spatial distribution of chloride in uncracked concrete subjected to homogeneous exposure. Chloride concentrations were measured with potentiometric sensors embedded in concr

  17. Viscosity and density tables of sodium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Fair, J.A.; Ozbek, H. (comps.)

    1977-04-01

    A file is presented containing tabulated data extracted from the scientific literature on the density and viscosity of aqueous sodium chloride solutions. Also included is a bibliography of the properties of aqueous sodium chloride solutions. (MHR)

  18. Hydrolysis of ferric chloride in solution

    Energy Technology Data Exchange (ETDEWEB)

    Lussiez, G.; Beckstead, L.

    1996-11-01

    The Detox{trademark} process uses concentrated ferric chloride and small amounts of catalysts to oxidize organic compounds. It is under consideration for oxidizing transuranic organic wastes. Although the solution is reused extensively, at some point it will reach the acceptable limit of radioactivity or maximum solubility of the radioisotopes. This solution could be cemented, but the volume would be increased substantially because of the poor compatibility of chlorides and cement. A process has been developed that recovers the chloride ions as HCl and either minimizes the volume of radioactive waste or permits recycling of the radioactive chlorides. The process involves a two-step hydrolysis at atmospheric pressure, or preferably under a slight vacuum, and relatively low temperature, about 200{degrees}C. During the first step of the process, hydrolysis occurs according to the reaction below: FeCl{sub 3 liquid} + H{sub 2}O {r_arrow} FeOCl{sub solid} + 2 HCl{sub gas} During the second step, the hot, solid, iron oxychloride is sprayed with water or placed in contact with steam, and hydrolysis proceeds to the iron oxide according to the following reaction: 2 FeOCl{sub solid} + H{sub 2}O {r_arrow} Fe{sub 2}O{sub 3 solid} + 2 HCl{sub gas}. The iron oxide, which contains radioisotopes, can then be disposed of by cementation or encapsulation. Alternately, these chlorides can be washed off of the solids and can then either be recycled or disposed of in some other way.

  19. Investigation of factors influencing chloride extraction efficiency during electrochemical chloride extraction from reinforcing concrete

    Science.gov (United States)

    Sharp, Stephen R.

    2005-11-01

    Electrochemical chloride extraction (ECE) is an accelerated bridge restoration method similar to cathodic protection, but operates at higher current densities and utilizes a temporary installation. Both techniques prolong the life of a bridge by reducing the corrosion rate of the reinforcing bar when properly applied. ECE achieves this by moving chlorides away from the reinforcement and out of the concrete while simultaneously increasing the alkalinity of the electrolyte near the reinforcing steel. Despite the proven success, significant use of ECE has not resulted in part due to an incomplete understanding in the following areas: (1) An estimation of the additional service life that can be expected following treatment when the treated member is again subjected to chlorides; (2) The cause of the decrease in current flow and, therefore, chloride removal rate during treatment; (3) Influence of water-to-cement (w/c) ratio and cover depth on the time required for treatment. This dissertation covers the research that is connected to the last two areas listed above. To begin examining these issues, plain carbon steel reinforcing bars (rebar) were embedded in portland cement concrete slabs of varying water-to-cement (w/c) ratios and cover depths, and then exposed to chlorides. A fraction of these slabs had sodium chloride added as an admixture, with all of the slabs subjected to cyclical ponding with a saturated solution of sodium chloride. ECE was then used to remove the chlorides from these slabs while making electrical measurements in the different layers between the rebar (cathode) and the titanium mat (anode) to follow the progress of the ECE process. During this study, it was revealed that the resistance of the outer concrete surface layer increases during ECE, inevitably restricting current flow, while the resistance of the underlying concrete decreases or remains constant. During ECE treatment, a white residue formed on the surface of the concrete. Analyses of the

  20. Aspergilli Response to Benzalkonium Chloride and Novel-Synthesized Fullerenol/Benzalkonium Chloride Nanocomposite

    OpenAIRE

    Nikola Unković; Milica Ljaljević Grbić; Miloš Stupar; Jelena Vukojević; Vesna Janković; Danica Jović; Aleksandar Djordjević

    2015-01-01

    A comprehensive comparative analysis of antifungal potential of benzalkonium chloride and newly synthesized fullerenol/benzalkonium chloride nanocomposite was conducted to assess the possible impact of carbon-based nanocarrier on antimicrobial properties of the commonly used biocide. Physical characterization of synthesized nanocomposite showed zeta potential of +37.4 mV and inhomogeneous particles size distribution, with nanocomposite particles’ dimensions within 30–143 nm and maximum number...

  1. Prenatal susceptibility to carcinogenesis by xenobiotic substances including vinyl chloride.

    OpenAIRE

    Rice, J M

    1981-01-01

    The carcinogenicity of vinyl chloride for experimental animals when administered transplacentally is reviewed in comparison with known transplacental carcinogens, including those that, like vinyl chloride, are dependent on enzyme-mediated metabolic conversion to a reactive intermediate in maternal or fetal tissues. Vinyl chloride is converted by mixed-function oxidases to the reactive metabolite chlorooxirane, the carcinogenicity of which is also reviewed. Vinyl chloride is unequivocally a tr...

  2. Neutrophils employ the myeloperoxidase system to generate antimicrobial brominating and chlorinating oxidants during sepsis

    OpenAIRE

    Gaut, Joseph P.; Yeh, George C.; Tran, Hung Duy; Byun, Jaeman; Henderson, Jeffrey P.; Richter, Grace M.; Brennan, Marie-Luise; Lusis, Aldons J.; Belaaouaj, Abderrazzaq; Richard S Hotchkiss; Heinecke, Jay W.

    2001-01-01

    The myeloperoxidase system of neutrophils uses hydrogen peroxide and chloride to generate hypochlorous acid, a potent bactericidal oxidant in vitro. In a mouse model of polymicrobial sepsis, we observed that mice deficient in myeloperoxidase were more likely than wild-type mice to die from infection. Mass spectrometric analysis of peritoneal inflammatory fluid from septic wild-type mice detected elevated concentrations of 3-chlorotyrosine, a characteristic end product of the myeloperoxidase s...

  3. Stability of Alprostadil in 0.9% Sodium Chloride Stored in Polyvinyl Chloride Containers.

    Science.gov (United States)

    McCluskey, Susan V; Kirkham, Kylian; Munson, Jessica M

    2017-01-01

    The stability of alprostadil diluted in 0.9% sodium chloride stored in polyvinyl chloride (VIAFLEX) containers at refrigerated temperature, protected from light, is reported. Five solutions of alprostadil 11 mcg/mL were prepared in 250 mL 0.9% sodium chloride polyvinyl chloride (PL146) containers. The final concentration of alcohol was 2%. Samples were stored under refrigeration (2°C to 8°C) with protection from light. Two containers were submitted for potency testing and analyzed in duplicate with the stability-indicating high-performance liquid chromatography assay at specific time points over 14 days. Three containers were submitted for pH and visual testing at specific time points over 14 days. Stability was defined as retention of 90% to 110% of initial alprostadil concentration, with maintenance of the original clear, colorless, and visually particulate-free solution. Study results reported retention of 90% to 110% initial alprostadil concentration at all time points through day 10. One sample exceeded 110% potency at day 14. pH values did not change appreciably over the 14 days. There were no color changes or particle formation detected in the solutions over the study period. This study concluded that during refrigerated, light-protected storage in polyvinyl chloride (VIAFLEX) containers, a commercial alcohol-containing alprostadil formulation diluted to 11 mcg/mL with 0.9% sodium chloride 250 mL was stable for 10 days.

  4. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Quaternary ammonium chloride combination. 172.165... HUMAN CONSUMPTION Food Preservatives § 172.165 Quaternary ammonium chloride combination. The food additive, quaternary ammonium chloride combination, may be safely used in food in accordance with...

  5. Intrinsic Resistance of Burkholderia cepacia Complex to Benzalkonium Chloride

    OpenAIRE

    Youngbeom Ahn; Jeong Myeong Kim; Ohgew Kweon; Seong-Jae Kim; Jones, Richard C.; Kellie Woodling; Goncalo Gamboa da Costa; LiPuma, John J.; David Hussong; Marasa, Bernard S.; Cerniglia, Carl E.

    2016-01-01

    ABSTRACT Pharmaceutical products that are contaminated with Burkholderia cepacia complex (BCC) bacteria may pose serious consequences to vulnerable patients. Benzyldimethylalkylammonium chloride (BZK) cationic surfactants are extensively used in medical applications and have been implicated in the coselection of antimicrobial resistance. The ability of BCC to degrade BZK, tetradecyldimethylbenzylammonium chloride (C14BDMA-Cl), dodecyldimethylbenzylammonium chloride (C12BDMA-Cl), decyldimethyl...

  6. Retention of vinyl chloride in the human lung.

    OpenAIRE

    Krajewski, J.; Dobecki, M; Gromiec, J

    1980-01-01

    Experiments with volunteers showed that 42% of an inhaled dose of vinyl chloride is retained in the lungs. This value is independent of the concentration of vinyl chloride in the air. Elimination of vinyl chloride through the lungs is negligible since its concentration in expired air decreases immediately after the cessation of exposure.

  7. Kinetics of Vinyl Chloride Polymerization with Mixture of Initiators

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Kinetic models for the rate constants of vinyl chloride polymerization in the presence of initiator mixtures were proposed. They may be used to design the initiator recipes for the vinyl chloride polymerization with uniform rate at different temperatures at which various grades of poly(vinyl chloride) will be prepared.

  8. 46 CFR 154.1740 - Vinyl chloride: Inhibiting and inerting.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride: Inhibiting and inerting. 154.1740... Operating Requirements § 154.1740 Vinyl chloride: Inhibiting and inerting. When a vessel is carrying vinyl chloride, the master shall ensure that: (a) Section 154.1818 is met; or (b) Section 154.1710 is met,...

  9. The role of bromine and chlorine chemistry for arctic ozone depletion events in Ny-Ålesund and comparison with model calculations

    Directory of Open Access Journals (Sweden)

    M. Martinez

    Full Text Available During the Arctic Tropospheric Ozone Chemistry (ARCTOC campaigns at Ny-Ålesund, Spitsbergen, the role of halogens in the depletion of boundary layer ozone was investigated. In spring 1995 and 1996 up to 30 ppt bromine monoxide were found whenever ozone decreased from normal levels of about 40 ppb. Those main trace gases and others were specifically followed in the UV-VIS spectral region by differential optical absorption spectroscopy (DOAS along light paths running between 20 and 475 m a.s.l.. The daily variation of peroxy radicals closely followed the ozone photolysis rate J(O3(O1D in the absence of ozone depletion most of the time. However, during low ozone events this close correlation was no longer found because the measurement of radicals by chemical amplification (CA turned out to be sensitive to peroxy radicals and ClOx. Large CA signals at night can sometimes definitely be assigned to ClOx and reached up to 2 ppt. Total bromine and iodine were both stripped quantitatively from air by active charcoal traps and measured after neutron activation of the samples. Total bromine increased from background levels of about 15 ppt to a maximum of 90 ppt during an event of complete ozone depletion. For the spring season a strong source of bromine is identified in the pack ice region according to back trajectories. Though biogenic emission sources cannot be completely ruled out, a primary activation of halogenides by various oxidants seems to initiate an efficient autocatalytic process, mainly driven by ozone and light, on ice and perhaps on aerosols. Halogenides residing on pack ice surfaces are continuously oxidised by hypohalogenous acids releasing bromine and chlorine into the air. During transport and especially above open water this air mixes with upper layer pristine air. As large quantities of bromine, often in the form of BrO, have been observed at polar sunrise also around Antarctica, its release

  10. Novel analytical approach for brominated flame retardants based on the use of gas chromatography-atmospheric pressure chemical ionization-tandem mass spectrometry with emphasis in highly brominated congeners.

    Science.gov (United States)

    Portolés, Tania; Sales, Carlos; Gómara, Belén; Sancho, Juan Vicente; Beltrán, Joaquim; Herrero, Laura; González, María José; Hernández, Félix

    2015-10-06

    The analysis of brominated flame retardants (BFRs) commonly relies on the use of gas chromatography coupled to mass spectrometry (GC-MS) operating in electron ionization (EI) and electron capture negative ionization (ECNI) modes using quadrupole, triple quadrupole, ion trap, and magnetic sector analyzers. However, these brominated contaminants are examples of compounds for which a soft and robust ionization technique might be favorable since they show high fragmentation in EI and low specificity in ECNI. In addition, the low limits of quantification (0.01 ng/g) required by European Commission Recommendation 2014/118/EU on the monitoring of traces of BFRs in food put stress on the use of highly sensitive techniques/methods. In this work, a new approach for the extremely sensitive determination of BFRs taking profit of the potential of atmospheric pressure chemical ionization (APCI) combined with GC and triple quadrupole (QqQ) mass analyzer is proposed. The objective was to explore the potential of this approach for the BFRs determination in samples at pg/g levels, taking marine samples and a cream sample as a model. Ionization and fragmentation behavior of 14 PBDEs (congeners 28, 47, 66, 85, 99, 100, 153, 154, 183, 184, 191, 196, 197, and 209) and two novel BFRs, decabromodiphenyl ethane (DBDPE) and 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE), in the GC-APCI-MS system has been investigated. The formation of highly abundant (quasi) molecular ion was the main advantage observed in relation to EI. Thus, a notable improvement in sensitivity and specificity was observed when using it as precursor ion in tandem MS. The improved detectability (LODs < 10 fg) achieved when using APCI compared to EI has been demonstrated, which is especially relevant for highly brominated congeners. Analysis of samples from an intercomparison exercise and samples from the marine field showed the potential of this approach for the reliable identification and quantification at very low

  11. Relation between chloride exchange diffusion and a conductive chloride pathway across the isolated skin of the toad (Bufo bufo)

    DEFF Research Database (Denmark)

    Kristensen, P; Larsen, Erik Hviid

    1978-01-01

    Substitution of chloride in the outside bathing medium of the toad skin with bromide, iodide, nitrate and sulphate leads to a reduction in the apparent exchange diffusion of chloride across this tissue, and also to a reduction of the chloride current recorded during hyperpolarization. A series of...

  12. 40 CFR 61.64 - Emission standard for polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... Standard for Vinyl Chloride § 61.64 Emission standard for polyvinyl chloride plants. An owner or operator of a polyvinyl chloride plant shall comply with the requirements of this section and § 61.65. (a... is not to exceed 0.02 g vinyl chloride/kg (0.04 lb vinyl chloride/ton) of polyvinyl chloride...

  13. Calcium/thionyl chloride battery technology

    Science.gov (United States)

    Counts, T.

    1985-12-01

    This final report documents the development efforts conducted by the Lithium Batteries Group of the Couples Department of Eagle-Picher Industries. The objective of the project was to develop calcium-thionyl chloride cell technology. The original project was divided into two main tasks. Task One was to consist of component optimization and stability studies. Once sufficiently advanced, the ongoing results of Task One were to be integrated with Task Two. Task Two was to consist of demonstration of an optimized primary cell. In July, 1983, the program was redirected. Task Two was split, with effort to be directed toward both the original primary cell and toward a high discharge rate reserve configuration cell. Additional electrolyte salts were to be evaluated as a means of improving the storability of the active calcium-thionyl chloride cell.

  14. Benzalkonium chloride. Health hazard evaluation report

    Energy Technology Data Exchange (ETDEWEB)

    Bernholc, N.M.

    1984-01-01

    Health hazards associated with the use of benzalkonium chlorides (BAC) are reviewed. Benzalkonium chloride is extensively used as a cationic disinfectant. It is found in a great many over-the-counter and prescription eye products, disinfectants, shampoos, and deodorants, and is used in concentrations that range from 0.001 to 0.01% in eyedrops, up to 2.5% in concentrated liquid disinfectants. Solutions of 0.03 to 0.04% BAC may cause temporary eye irritation in humans but are unlikely to cause any skin response except in persons allergic to quaternary ammonium compounds. Inhalation of a vaporized 10% solution of BAC produced a bronchospasmodic reaction in a previously sensitized individual. At present no other human health effects from BAC have been documented or inferred from exposure to such dilute concentrations.

  15. BARRIER PROPERTIES OF VINYLIDENE CHLORIDE COPOLYMERS

    Institute of Scientific and Technical Information of China (English)

    LI Yuesheng; WENG Zhixue; HUANG Zhiming; PAN Zuren

    1996-01-01

    The permeability coefficients of a series of copolymers of vinylidene chloride (VDC)with methyl acrylate (MA), butyl acrylate (BA) or vinyl chloride (VC) (as comonomer)to oxygen and carbon dioxide have been measured at 1.0 MPa and 30℃, while those to water vapor have been measured at 30℃ and 100% relative humidity. All the copolymers are semicrystalline. VDC/MA copolymers have lower melting temperature compared with VDC/BA copolymers, while that melting temperature of VDC/VC copolymer is higher than that of VDC/acrylate copolymers with the same VDC content. The barrier property of the copolymers is predominantly controlled by crystallite, free volume fraction, and cohesive energy. The permeability coefficients of VDC/MA copolymers to oxygen, carbon dioxide, and water vapor were successfully correlated with the ratio of free volume to cohesive energy.

  16. STABILISATION OF SILTY CLAY SOIL USING CHLORIDE

    Directory of Open Access Journals (Sweden)

    TAMADHER T. ABOOD

    2007-04-01

    Full Text Available The object of this paper is to investigate the effect of adding different chloride compounds including (NaCl, MgCl2, CaCl2 on the engineering properties of silty clay soil. Various amounts of salts (2%, 4%, and 8% were added to the soil to study the effect of salts on the compaction characteristics, consistency limits and compressive strength. The main findings of this study were that the increase in the percentage of each of the chloride compounds increased the maximum dry density and decrease the optimum moisture content. The liquid limit, plastic limit and plasticity index decreased with the increase in salt content. The unconfinedcompressive strength increased as the salt content increased.

  17. Iron (III) chloride doping of CVD graphene.

    Science.gov (United States)

    Song, Yi; Fang, Wenjing; Hsu, Allen L; Kong, Jing

    2014-10-03

    Chemical doping has been shown as an effective method of reducing the sheet resistance of graphene. We present the results of our investigations into doping large area chemical vapor deposition graphene using Iron (III) Chloride (FeCl(3)). It is shown that evaporating FeCl(3) can increase the carrier concentration of monolayer graphene to greater than 10(14) cm(-2) and achieve resistances as low as 72 Ω sq(-1). We also evaluate other important properties of the doped graphene such as surface cleanliness, air stability, and solvent stability. Furthermore, we compare FeCl(3) to three other common dopants: Gold (III) Chloride (AuCl(3)), Nitric Acid (HNO(3)), and TFSA ((CF(3)SO(2))(2)NH). We show that compared to these dopants, FeCl(3) can not only achieve better sheet resistance but also has other key advantages including better solvent stability.

  18. Inhibition of thyroid hormone sulfotransferase activity by brominated flame retardants and halogenated phenolics.

    Science.gov (United States)

    Butt, Craig M; Stapleton, Heather M

    2013-11-18

    Many halogenated organic contaminants (HOCs) are considered endocrine disruptors and affect the hypothalamic-pituitary-thyroid axis, often by interfering with circulating levels of thyroid hormones (THs). We investigated one potential mechanism for TH disruption, inhibition of sulfotransferase activity. One of the primary roles of TH sulfation is to support the regulation of biologically active T3 through the formation of inactive THs. We investigated TH sulfotransferase inhibition by 14 hydroxylated polybrominated diphenyl ethers (OH BDEs), BDE 47, triclosan, and fluorinated, chlorinated, brominated, and iodinated analogues of 2,4,6-trihalogenated phenol and bisphenol A (BPA). A new mass spectrometry-based method was also developed to measure the formation rates of 3,3'-T2 sulfate (3,3'-T2S). Using pooled human liver cytosol, we investigated the influence of these HOCs on the sulfation of 3,3'-T2, a major substrate for TH sulfation. For the formation of 3,3'-T2S, the Michaelis constant (Km) was 1070 ± 120 nM and the Vmax was 153 ± 6.6 pmol min(-1) (mg of protein)(-1). All chemicals investigated inhibited sulfotransferase activity with the exception of BDE 47. The 2,4,6-trihalogenated phenols were the most potent inhibitors followed by the OH BDEs and then halogenated BPAs. The IC50 values for the OH BDEs were primarily in the low nanomolar range, which may be environmentally relevant. In silico molecular modeling techniques were also used to simulate the binding of OH BDE to SULT1A1. This study suggests that some HOCs, including antimicrobial chemicals and metabolites of flame retardants, may interfere with TH regulation through inhibition of sulfotransferase activity.

  19. Fabric phase sorptive extraction: Two practical sample pretreatment techniques for brominated flame retardants in water.

    Science.gov (United States)

    Huang, Guiqi; Dong, Sheying; Zhang, Mengfei; Zhang, Haihan; Huang, Tinglin

    2016-09-15

    Sample pretreatment is the critical section for residue monitoring of hazardous pollutants. In this paper, using the cellulose fabric as host matrix, three extraction sorbents such as poly (tetrahydrofuran) (PTHF), poly (ethylene glycol) (PEG) and poly (dimethyldiphenylsiloxane) (PDMDPS), were prepared on the surface of the cellulose fabric. Two practical extraction techniques including stir bar fabric phase sorptive extraction (stir bar-FPSE) and magnetic stir fabric phase sorptive extraction (magnetic stir-FPSE) have been designed, which allow stirring of fabric phase sorbent during the whole extraction process. In the meantime, three brominated flame retardants (BFRs) [tetrabromobisphenol A (TBBPA), tetrabromobisphenol A bisallylether (TBBPA-BAE), tetrabromobisphenol A bis(2,3-dibromopropyl)ether (TBBPA-BDBPE)] in the water sample were selected as model analytes for the practical evaluation of the proposed two techniques using high-performance liquid chromatography (HPLC). Moreover, various experimental conditions affecting extraction process such as the type of fabric phase, extraction time, the amount of salt and elution conditions were also investigated. Due to the large sorbent loading capacity and unique stirring performance, both techniques possessed high extraction capability and fast extraction equilibrium. Under the optimized conditions, high recoveries (90-99%) and low limits of detection (LODs) (0.01-0.05 μg L(-1)) were achieved. In addition, the reproducibility was obtained by evaluating the intraday and interday precisions with relative standard deviations (RSDs) less than 5.1% and 6.8%, respectively. The results indicated that two pretreatment techniques were promising and practical for monitoring of hazardous pollutants in the water sample. Due to low solvent consumption and high repeated use performance, proposed techniques also could meet green analytical criteria.

  20. Response of wheat and pea seedlings on increase of bromine concentration in the growth medium.

    Science.gov (United States)

    Shtangeeva, Irina; Niemelä, Matti; Perämäki, Paavo; Timofeev, Sergey

    2015-12-01

    Biogeochemical cycles of bromine (Br) and its quantitative requirements for different plant species are still studied poorly. There is a need to examine Br pathways in plants and evaluate the factors important for Br accumulation in a plant. In the present work, the effects of different Br compounds on an uptake of Br by two plant species (wheat and pea) that tolerate Br differently (pea is more sensitive to Br compared with wheat) have been studied. The growth medium was spiked with either KBr or NaBr at concentrations 0, 10, 50 and 100 mg/L. Elemental analysis of the plants was performed using inductively coupled plasma optical emission spectrometry (ICP-OES) and ICP-MS analytical techniques after leaching of the samples with tetramethyl ammonium hydroxide at mild temperature (60 °C). The experimental results have shown that wheat and pea seedlings can accumulate rather large amounts of Br. An increase of Br concentration in a plant was not always directly proportional to the variations in the Br concentration in the growth medium. In wheat, the greater part of Br was accumulated during first 7 days. In pea, the uptake of Br lasted until the end of the experiment. Certain differences in the ability of plants to accumulate Br were observed when the plants were grown in a medium spiked with different Br compounds. In most cases, Br accumulation was higher in the leaves of the plants grown in the medium spiked with KBr. The same tendency was observed for another halogen, chlorine (Cl).

  1. Critical review of the analysis of brominated flame retardants and their environmental levels in Africa.

    Science.gov (United States)

    Brits, Martin; de Vos, Jayne; Weiss, Jana M; Rohwer, Egmont R; de Boer, Jacob

    2016-12-01

    World-wide, the prevalence of brominated flame retardants (BFRs) is well documented for routine analysis of environmental and biological matrices. There is, however, limited information on these compounds in the African environment and insufficient information on the analytical approaches used to obtain data. This paper presents a review on BFR levels in the African environment and the various analytical methodologies specifically applied in Africa for polybrominated diphenyl ethers (PBDEs), polybrominated biphenyls and alternative-BFRs. The analyses include liquid sample preparation using liquid-liquid and solid phase extraction and solid sample preparation involving Soxhlet extraction, with ultrasound-assisted extraction increasingly being applied. Instrumental detection techniques were limited to gas chromatography coupled with electron capture detector and electron impact ionisation with single quadrupole mass spectrometers. Information on congener profile prevalence in indoor dust, soil, aquatic environment (water, sediment, and aquatic organisms), eggs, wastewater treatment plant compartments, landfills (leachate and sediment) and breast milk are presented. Although PBDEs were inconsistently detected, contamination was reported for all investigated matrices in the African environment. The manifestation in remote regions indicates the ubiquitous prevalence and long-range transport of these compounds. Levels in sediment, and breast milk from some African countries were higher than reported for Asia and Europe. Due to limited data or non-detection of alternative-BFRs, it is unclear whether banned formulations were replaced in Africa. Most of the data reported for BFR levels in Africa were obtained in non-African laboratories or in South Africa and formed the basis for our discussion of reported contamination levels and related methodologies.

  2. Evaluation of Common Use Brominated Flame Retardant (BFR Toxicity Using a Zebrafish Embryo Model

    Directory of Open Access Journals (Sweden)

    Crystal Y. Usenko

    2016-09-01

    Full Text Available Brominated flame retardants (BFRs are used to reduce the flammability of plastics, textiles, and electronics. BFRs vary in their chemical properties and structures, and it is expected that these differences alter their biological interactions and toxicity. Zebrafish were used as the model organism for assessing the toxicity of nine structurally-diverse BFRs. In addition to monitoring for overt toxicity, the rate of spontaneous movement, and acetylcholinesterase and glutathione-S-transferase (GST activities were assessed following exposure. The toxicities of BFRs tested can be ranked by LC50 as tetrabromobisphenol A (TBBPA < 4,4′-isopropylidenebis[2-(2,6-dibromophenoxylethanol] (TBBPA-OHEE < Pentabromochlorocyclohexane (PBCH < 2-ethylhexyl 2,3,4,5-tetrabromobenzoate (TBB < hexabromocyclododecane (HBCD < hexabromobenzene (HBB < Tetrabromophthalic anhydride (PHT4. No adverse effect was observed in di(2-ethylhexyl tetrabromophthalate (TBPH or dibromoneopentyl glycol (DBNPG-treated embryos. The rate of spontaneous movement was decreased in a concentration-dependent manner following exposure to four of the nine compounds. GST activity was elevated following treatment with PBCH, TBBPA, HBCD, and HBB. The results indicate that exposure to several BFRs may activate an antioxidant response and alter behavior during early development. Some of the BFRs, such as TBBPA and TBBPA-OHEE, induced adverse effects at concentrations lower than chemicals that are currently banned. These results suggest that zebrafish are sensitive to exposure to BFRs and can be used as a comparative screening model, as well as to determine alterations in behavior following exposure and probe mechanisms of action.

  3. Associations between brominated flame retardants in house dust and hormone levels in men

    Science.gov (United States)

    Johnson, Paula I.; Stapleton, Heather M.; Mukherjee, Bhramar; Hauser, Russ; Meeker, John D.

    2013-01-01

    Brominated flame retardants (BFRs) are used in the manufacture of a variety of materials and consumer products in order to meet fire safety standards. BFRs may persist in the environment and have been detected in wildlife, humans and indoor dust and air. Some BFRs have demonstrated endocrine and reproductive effects in animals, but human studies are limited. In this exploratory study, we measured serum hormone levels and flame retardant concentrations [31 polybrominated diphenyl ether (PBDE) congeners and 6 alternate flame retardants] in house dust from men recruited through a US infertility clinic. PBDE congeners in dust were grouped by commercial mixtures (i.e. penta-, octaand deca-BDE). In multivariable linear regression models adjusted by age and body mass index (BMI), significant positive associations were found between house dust concentrations of pentaBDEs and serum levels of free T4, total T3, estradiol, and sex hormone binding globulin (SHBG), along with an inverse association with follicle stimulating hormone (FSH). There were also positive associations of octaBDE concentrations with serum free T4, thyroid stimulating hormone (TSH), luteinizing hormone (LH) and testosterone and an inverse association of decaBDE concentrations with testosterone. Hexabromocyclododecane (HBCD) was associated with decreased SHBG and increased free androgen index. Dust concentrations of bis-tribromophenoxyethane (BTBPE) and tetrabromo-diethylhexylphthalate (TBPH) were positively associated with total T3. These findings are consistent with our previous report of associations between PBDEs (BDE 47, 99 and 100) in house dust and hormone levels in men, and further suggest that exposure to contaminants in indoor dust may be leading to endocrine disruption in men. PMID:23333513

  4. Industry-sponsored research on the potential health and environmental effects of selected brominated flame retardants.

    Science.gov (United States)

    Hardy, M L; Biesemeier, J; Manor, O; Gentit, W

    2003-09-01

    Modern fire-fighting techniques, equipment and fire-resistant building design has lead to less destruction than in the previous centuries. However, a high fuel load in either a residence or a commercial building can overwhelm even the best firefighters or building construction, and factors affecting the fuel load have changed in recent decades. The fire load in a typical home has doubled over the last 50 years, furnishings typically include those made of petrochemicals that can behave as if containing built-in accelerant, and modern energy-efficient buildings are less able to disperse heat in the event of a fire. Flame retardant chemicals (FRs) are one means used to reduce the risk of fire. FRs are typically added or incorporated chemically into a polymer to slow or hinder the ignition or growth of a fire in low-to-moderate cost commodity polymers. One type of FR contains bromine atoms as the active moiety. The FR industry, either as individual companies or as consortia, has conducted a broad range of studies on the commercial deca-, octa- and pentabromodiphenyl oxide/ether, tetrabromobisphenol A and hexabromocyclododecane products. These five products have data in excess of the OECD Screening Informational Data Set (SIDS) and the U.S. High Production Volume (HPV) program, and sufficient data for the performance of formal EU risk assessments. The objective of this paper is to present the range of data developed by industry consortia and to provide sources for the information. We hope to facilitate further research by assembling references to industry consortia-sponsored research here.

  5. Chlorinated and brominated organic contaminants in fish from Shanghai markets: a case study of human exposure.

    Science.gov (United States)

    Qiu, Yanling; Strid, Anna; Bignert, Anders; Zhu, Zhiliang; Zhao, Jianfu; Athanasiadou, Maria; Athanassiadis, Ioannis; Bergman, Åke

    2012-10-01

    In the present study were two favorite edible fish species for local residents, i.e., mandarin fish and crawfish, collected from the Shanghai market and analyzed for selected organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs), hexabromocyclododecane (HBCDD), polybrominated diphenyl ethers (PBDEs) and methoxylated PBDEs (MeO-PBDEs). Efforts were also made to identify the potential sources of these contaminants. Comparable concentrations of hexachlorocyclohexanes (HCHs), dichlorodiphenyltrichloroethanes (DDTs) and HBCDD were found in muscle tissue of mandarin fish from Guangdong (GDF), the Pearl River Delta and from Taihu Lake (TLF), the Yangtze River Delta. Levels of chlordanes, PCBs and PBDEs were about one magnitude lower in TLF compared to GDF. The concentrations of OCPs in the butter-like gland of the crawfish (CFB) were 2-5 times of those in the crawfish muscle (CFM) while concentrations of PCBs, PBDEs and MeO-PBDEs were comparable. The different patterns and levels of chlorinated and brominated organohalogen contaminants seen in mandarin fish from GDF and TLF indicates that different types of chemicals might be used in the two delta regions. The present study also shows a good correlation between the concentrations of hexachlorobenzene (HCB) and pentachloroanisol (PCA) in fish for the first time. Fish consumption limits based on chemical contaminants with non-carcinogenic effects were calculated. The estimated maximum daily consumption limit for GDF, TLF, CFM and CFB were 1.5, 2.6, 3.7 and 0.08 kg, respectively, indicating no significant risk regarding the persistent organic pollutants measured in the present study.

  6. Leaching characteristics of heavy metals and brominated flame retardants from waste printed circuit boards

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Xiaoyu [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Guo, Jie, E-mail: guojie@ecust.edu.cn [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Lin, Kuangfei [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Shanghai Key Laboratory of Functional Materials Chemistry, East China University of Science and Technology, Shanghai 200237 (China); Huang, Kai; Deng, Jingjing [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China)

    2013-02-15

    Highlights: ► Cu and Pb were the most leachable heavy metals in WPCBs according to TCLP and SPLP. ► Penta-BDE congeners were dominated in all extracts. ► High dissolved organic matter condition promoted the BFRs leaching rate. ► Leaching from WPCBs was a significant emission source of BFRs in landfill. -- Abstract: Leaching assessment on five heavy metals (copper, zinc, lead, nickel and cadmium) and two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs) and tetrabromobisphenol A (TBBPA), from waste printed circuit boards (WPCBs) were conducted using various leaching methods. The mean leaching concentrations of copper were the highest in both toxicity characteristic leaching procedures (TCLP) and synthetic precipitation leaching procedures (SPLP) tests at 8.6 mg/L and 1.1 mg/L, while only lead (6.2 mg/L) exceeded the TCLP criteria and Chinese EPA regulatory limit (both 5.0 mg/L). However, PBDEs and TBBPA were not detected in TCLP and SPLP tests. Then the BFRs leaching trends and potential leachabilities were further investigated in actual landfill leachates using a modified method. Leaching characteristics that fast-leaching initially followed by slow-desorption over time were generally observed. In landfill leachate tests, the highest leaching concentrations of PBDEs and TBBPA were determined at 30.39 and 12.27 μg/L. Meanwhile, the highest leaching rates were estimated to reach 0.08% and 1.00%, respectively, which were significantly influenced by the dissolved organic carbon contents of extracts, the hydrophobicities of target BFRs and the specific surface areas of WPCBs materials. These results proved that leaching from WPCBs was a significant emission source of BFRs in landfill and electronic waste recycling dumpsite.

  7. Photochemical reactions of brominated diphenylethers in organic solvents and adsorbed on silicon dioxide in aqueous suspension

    Energy Technology Data Exchange (ETDEWEB)

    Palm, W.U.; Kopetzky, R.; Sossinka, W.; Ruck, W. [Univ. of Lueneburg, Environmental Chemistry, Lueneburg (Germany); Zetzsch, C. [Univ. of Bayreuth, Atmos. Chem. Research, Bayreuth, and Fraunhofer-Inst. of Toxicology and Experimental Medicine, Hannover (Germany)

    2004-09-15

    Polybrominated diphenylethers (BDEs) are in use as flame retardants worldwide and are found as xenobiotics in environmental samples. Photolysis by sunlight, one of the potential abiotic degradation pathways, is found to be rapid in laboratory experiments, especially for deca-BDE, the most prominent BDE as compared to commercial penta- and octa-BDEs. Due to the extremely low water solubility of BDEs, these experiments were mostly performed in organic solvents so far, and a few in environmental matrices (sand and soil) and on dry and hydrated quartz glass. However, detailed UV absorption spectra of deca-BDE and debrominated BDEs in the relevant wavelength range above 300 nm have become available only recently, besides the UV maxima of a number of synthesized congeners at shorter wavelengths and an exploratory study from our laboratory. Other important parameters to assess the abiotic degradation in the environment, such as OH-rate constants and photolytic quantum yields of BDEs are not available. Furthermore, analysis of BDEs was mostly performed by GC-MS, and the capability of HPLC with a diode array detector (DAD) has not yet been exploited. This study presents kinetic results on the photolysis of BDEs in tetrahydrofuran (THF) with detailed photolytic pathways for a tetra-BDE (2,2'4,4'-BDE), a hexa-BDE (2,2'4,4',5,5'-BDE) and deca-BDE. Employing HPLC with a diode array detector (DAD) as analytical tool, quantum yields of BDEs with N{sub Br} = 1-10 are determined. Furthermore, the formation of brominated dibenzofurans (BDFs) was investigated. Since the environmental relevance of photolysis experiments in organic solvents is questionable, first results on photolysis of deca-BDE adsorbed on silicon dioxide particles, suspended in water, are presented.

  8. Formation of new brominated disinfection byproducts during chlorination of saline sewage effluents.

    Science.gov (United States)

    Ding, Guoyu; Zhang, Xiangru; Yang, Mengting; Pan, Yang

    2013-05-15

    Chlorination could be the most cost-effective method for disinfecting saline sewage effluents resulting from toilet flushing with seawater. Upon chlorination, the high levels of bromide ions in saline sewage effluents (up to 32 mg/L) can be oxidized to hypobromous acid/hypobromite, which could then react with organic matter in the sewage effluents to form brominated disinfection byproducts (Br-DBPs). In this study, primary and secondary saline sewage effluents were collected and chlorinated at different chlorine doses, and a powerful precursor ion scan method using ultra performance liquid chromatography/electrospray ionization-triple quadrupole mass spectrometry was adopted for detection and identification of polar Br-DBPs in these samples. With the new method, 54 major polar Br-DBPs were detected in the chlorinated saline effluents and six of them were newly identified as wastewater DBPs, including bromomaleic acid, 5-bromosalicylic acid, 3,5-dibromo-4-hydroxybenzaldehyde, 3,5-dibromo-4-hydroxybenzoic acid, 2,6-dibromo-4-nitrophenol, and 2,4,6-tribromophenol. The formation of polar Br-DBPs, especially those newly detected ones, during chlorination of the saline effluents was studied. For the secondary saline effluent, various polar Br-DBPs formed and reached their maximum levels at different chlorine doses, whereas for the primary saline effluent, the formation of polar Br-DBPs basically kept increasing with increasing chlorine dose. Compared with the secondary saline effluent, the primary saline effluent generated fewer and less Br-DBPs and rarely generated nitrogenous Br-DBPs.

  9. Characterization of bromine-76-labelled 5-bromo-6-nitroquipazine for PET studies of the serotonin transporter

    Energy Technology Data Exchange (ETDEWEB)

    Lundkvist, Camilla E-mail: Lundkvis@shfj.cea.fr; Loc' h, Christian; Halldin, Christer; Bottlaender, Michel; Ottaviani, Michele; Coulon, Christine; Fuseau, Chantal; Mathis, Chester; Farde, Lars; Maziere, Bernard

    1999-07-01

    The development of suitable radioligands for brain imaging of the serotonin transporter is of great importance for the study of depression and other affective disorders. The potent and selective serotonin transporter ligand, 5-iodo-6-nitro-2-piperazinylquinoline, has been labelled with iodine-123 and used as a radioligand for single photon emission computerized tomography. To evaluate the potential of the bromine-76-labelled analogue, 5-bromo-6-nitroquipazine, as a radioligand for positron emission tomography (PET), its brain distribution and binding characteristics were examined in rats. In vivo brain distribution and ex vivo autoradiography demonstrated that [{sup 76}Br]5-bromo-6-nitroquipazine enters the brain rapidly. The regional brain distribution of [{sup 76}Br]5-bromo-6-nitroquipazine was consistent with the known distribution of serotonin transporters in the midbrain, pons, thalamus, striatum, and neocortex. Specific binding was inhibited by the selective serotonin reuptake inhibitor citalopram. The peripheral metabolism in plasma was rapid, but more than 90% of the radioactivity in brain represented unchanged radioligand 2 h postinjection (p.i.). A preliminary PET study was also performed in a baboon. Following the intravenous injection of [{sup 76}Br]5-bromo-6-nitroquipazine in a baboon, there was a conspicuous accumulation of radioactivity in thalamus, striatum, and pons. The radioactivity in these brain regions was 1.5 times higher than in the cerebellum at 3 h and 2.5-4 times higher at 24 h. A rapid metabolism of the radioligand in plasma was observed (38% unchanged after 5 min). The results indicate that [{sup 76}Br]5-bromo-6-nitroquipazine has potential for PET imaging of the serotonin transporter.

  10. Geographical distribution of non-PBDE-brominated flame retardants in mussels from Asian coastal waters.

    Science.gov (United States)

    Isobe, Tomohiko; Ogawa, Shohei P; Ramu, Karri; Sudaryanto, Agus; Tanabe, Shinsuke

    2012-09-01

    Hexabromocyclododecanes (HBCDs), 1,2-bis(2,4,6-tribromophenoxy) ethane (BTBPE), and decabromodiphenyl ethane (DBDPE) used as alternatives for polybrominated diphenyl ethers (PBDEs) are also persistent in the environment as PBDEs. Limited information on these non-PBDE brominated flame retardants (BFRs) is available; in particular, there are only few publications on environmental pollution by these contaminants in the coastal waters of Asia. In this regard, we investigated the contamination status of HBCDs, BTBPE, and DBDPE in the coastal waters of Asia using mussels as a bioindicator. Concentrations of HBCDs, BTBPE, and DBDPE were determined in green (Perna viridis) and blue mussels (Mytilus edulis) collected from the coastal areas in Cambodia, China (mainland), SAR China (Hong Kong), India, Indonesia, Japan, Malaysia, the Philippines, and Vietnam on 2003-2008. BTBPE and DBDPE were analyzed using GC-MS, whereas HBCDs were determined by LC-MS/MS. HBCDs, BTBPE, and DBDPE were found in mussels at levels ranging from <0.01 to 1,400, <0.1 to 13, and <0.3 to 22 ng/g lipid wt, respectively. Among the three HBCD diastereoisomers, α-HBCD was the dominant isomer followed by γ- and β-HBCDs. Concentrations of HBCDs and DBDPE in mussels from Japan and Korea were higher compared to those from the other Asian countries, indicating extensive usage of these non-PBDE BFRs in Japan and Korea. Higher levels of HBCDs and DBDPE than PBDEs were detected in some mussel samples from Japan. The results suggest that environmental pollution by non-PBDE BFRs, especially HBCDs in Japan, is ubiquitous. This study provides baseline information on the contamination status of these non-PBDE BFRs in the coastal waters of Asia.

  11. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    OpenAIRE

    Güler, Ekrem; Olgar, Şeref; Davutoğlu, Mehmet; Garipardıç, Mesut; Karabiber, Hamza

    2011-01-01

    Benzalkonium chloride (BAC) is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is ...

  12. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    OpenAIRE

    Ekrem Güler; Şeref Olgar; Mehmet Davutoğlu; Mesut Garipardıç; Hamza Karabiber

    2014-01-01

    Benzalkonium chloride (BAC) is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is...

  13. EVALUATION OF BACTERICIDAL EFFECTIVENESS OF BENZALKONIUM CHLORIDE

    OpenAIRE

    K. Imandel; M.B. Shaywaard; F. Mobaraki

    1996-01-01

    Benzalkonium chloride is a quaternary ammounium Compounds derivative under different names such as Afxhang, Hamoon, Mahan etc, which have great and expanded use in sanitation and medical affairs. Bactericidal activity of these disinfectants was fulfilled according to National Standard Method No.2842 on Staph. Aureus, Sal. Typhimouium and E. coli. This laboratory test showed that, except Mahan that has not bactericidal efficacy on E.coli at concentration 0.4 percent, other disinfectants under ...

  14. Inactivation of Viruses by Benzalkonium Chloride

    Science.gov (United States)

    Armstrong, J. A.; Froelich, E. J.

    1964-01-01

    Benzalkonium chloride (as Roccal or Zephiran) was found to inactivate influenza, measles, canine distemper, rabies, fowl laryngotracheitis, vaccinia, Semliki Forest, feline pneumonitis, meningopneumonitis, and herpes simplex viruses after 10 min of exposure at 30 C or at room temperature. Poliovirus and encephalomyocarditis virus were not inactivated under the same conditions. It was concluded that all viruses tested were sensitive except members of the picorna group. The literature was reviewed. PMID:4288740

  15. Electrochemical Studies in Aluminum Chloride Melts

    Science.gov (United States)

    1976-07-31

    Molten Salt Systems", Symposium on Molten Salts, Symposium Volume, The Electrochemical Society , in press (1976). Manuscripts in Preparation--Related to...Fused Salt Technology, Electrochemical Society Meeting, Chicaao, May 8-13, 1973. R. A. Osteryoung, R. H. Abel, L. G. Boxall and B. H. Vassos, "An...aluminate Melts", Electrochemical Society , San Francisco, CA, May, 1974. R. A. Osteryoung, "Chemistry in Aluminum Chloride Melts", Fifth International

  16. Developing Polymer Cathode Material for the Chloride Ion Battery.

    Science.gov (United States)

    Zhao, Xiangyu; Zhao, Zhigang; Yang, Meng; Xia, Hui; Yu, Tingting; Shen, Xiaodong

    2017-01-25

    The chloride ion battery is an attractive rechargeable battery owing to its high theoretical energy density and sustainable components. An important challenge for research and development of chloride ion batteries lies in the innovation of the cathode materials. Here we report a nanostructured chloride ion-doped polymer, polypyrrole chloride, as a new type of potential cathode material for the chloride ion battery. The as-prepared polypyrrole chloride@carbon nanotubes (PPyCl@CNTs) cathode shows a high reversible capacity of 118 mAh g(-1) and superior cycling stability. Reversible electrochemical reactions of the PPyCl@CNTs cathode based on the redox reactions of nitrogen species and chloride ion transfer are demonstrated. Our work may guide and offer electrode design principles for accelerating the development of rechargeable batteries with anion transfer.

  17. The Accelerated Test of Chloride Permeability of Concrete

    Institute of Scientific and Technical Information of China (English)

    TAN Ke-feng; ODD E Gjφrv

    2003-01-01

    The availability of accelerated chloride permeability test and the effect of w/c ratio, incorporation of silica fume, maximum aggregate size and aggregate type on the chloride permeability were studied. The mathematic analysis certifies that there is a linear relationship between accelerated test and natural diffusion. Test results show that the chloride permeability of concrete increases as w/c ratio increases whilst a limited amount of replacement of cement with silica fume, the chloride permeability decreases dramatically. The maximum aggregate size in the range of 8 to 25 mm seems also affect chloride permeability but with a much less significant level. The chloride permeability of silica fume lightweight aggregate concrete is very low, especially the concrete made with dry lightweight concrete. The chloride permeability can be evaluated by this accelerated test method.

  18. Deriving an atmospheric budget of total organic bromine using airborne in-situ measurements from the Western Pacific during SHIVA

    Science.gov (United States)

    Sala, S.; Bönisch, H.; Keber, T.; Oram, D. E.; Mills, G.; Engel, A.

    2014-02-01

    During the SHIVA (Stratospheric Ozone: Halogen Impacts in a Varying Atmosphere) project an extensive dataset of all halogen species relevant for the atmospheric budget of total organic bromine has been collected in the West Pacific region using the FALCON aircraft operated by the German Aerospace agency DLR (Deutsches Zentrum für Luft- und Raumfahrt) covering a vertical range from the planetary boundary layer up to the ceiling altitude of the aircraft of 13 km. In total, more than 700 measurements were performed with the newly developed fully-automated in-situ instrument GHOST-MS (Gas cHromatograph for the Observation of Tracers - coupled with a Mass Spectrometer) by the Goethe University of Frankfurt (GUF) and with the onboard whole-air sampler WASP with subsequent ground based state-of-the-art GC/MS analysis by the University of East Anglia (UEA). Both instruments yield good agreement for all major (CHBr3 and CH2Br2) and minor (CHBrCl, CHBrCl2 and CHBr2Cl) VSLS (very short-lived substances), at least at the level of their 2 σ measurement uncertainties. In contrast to the suggestion that the Western Pacific could be a major source region for VSLS (Pyle et al., 2011), we found only slightly enhanced mixing ratios of brominated halogen source gases relative to the levels reported in Montzka et al. (2011) for other tropical regions. A budget for total organic bromine, including all four halons,CH3Br and the VSLS, is derived for the upper troposphere, the input region for the TTL and thus also for the stratosphere, compiled from the SHIVA dataset. With exception of the two minor VSLS CHBrCl2 and CHBr2Cl, excellent agreement with the values reported in Montzka et al. (2011) is found, while being slightly higher than previous studies from our group based on balloon-borne measurements.

  19. Field and Satellite Observations of the Formation and Distribution of Arctic Atmospheric Bromine Above a Rejuvenated Sea Ice Cover

    Science.gov (United States)

    Nghiem, Son V.; Rigor, Ignatius G.; Richter, Andreas; Burrows, John P.; Shepson, Paul B.; Bottenheim, Jan; Barber, David G.; Steffen, Alexandra; Latonas, Jeff; Wang, Feiyue; Stern, Gary; Clemente-Colon, Pablo; Martin, Seelye; Hall, Dorothy K.; Kaleschke, Lars; Tackett, Philip; Neumann, Gregory; Asplin, Matthew G.

    2012-01-01

    Recent drastic reduction of the older perennial sea ice in the Arctic Ocean has resulted in a vast expansion of younger and saltier seasonal sea ice. This increase in the salinity of the overall ice cover could impact tropospheric chemical processes. Springtime perennial ice extent in 2008 and 2009 broke the half-century record minimum in 2007 by about one million km2. In both years seasonal ice was dominant across the Beaufort Sea extending to the Amundsen Gulf, where significant field and satellite observations of sea ice, temperature, and atmospheric chemicals have been made. Measurements at the site of the Canadian Coast Guard Ship Amundsen ice breaker in the Amundsen Gulf showed events of increased bromine monoxide (BrO), coupled with decreases of ozone (O3) and gaseous elemental mercury (GEM), during cold periods in March 2008. The timing of the main event of BrO, O3, and GEM changes was found to be consistent with BrO observed by satellites over an extensive area around the site. Furthermore, satellite sensors detected a doubling of atmospheric BrO in a vortex associated with a spiral rising air pattern. In spring 2009, excessive and widespread bromine explosions occurred in the same region while the regional air temperature was low and the extent of perennial ice was significantly reduced compared to the case in 2008. Using satellite observations together with a Rising-Air-Parcel model, we discover a topographic control on BrO distribution such that the Alaskan North Slope and the Canadian Shield region were exposed to elevated BrO, whereas the surrounding mountains isolated the Alaskan interior from bromine intrusion.

  20. Potassium chloride production by microcline chlorination

    Energy Technology Data Exchange (ETDEWEB)

    Orosco, Pablo, E-mail: porosco@unsl.edu.ar [Instituto de Investigaciones en Tecnología Química (INTEQUI), Chacabuco y Pedernera, San Luis (Argentina); Facultad de Química, Bioquímica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, San Luis (Argentina); Ruiz, María del Carmen [Instituto de Investigaciones en Tecnología Química (INTEQUI), Chacabuco y Pedernera, San Luis (Argentina)

    2015-08-10

    Highlights: • Use of chlorination for the KCl production. • The reagents used were microcline, hydromagnesite and chlorine. • Isothermal and non-isothermal assays were performed in Cl{sub 2}–N{sub 2} mixture. • The chlorination generated KCl at 700 °C. • The chlorination products promote KCl formation. - Abstract: The potassium chloride is one of the most important fertilizers used in agriculture. The current demand of this salt makes interesting the study of potassium chloride production from unconventional potassium resources. In this work the potassium chloride production by chlorination of microcline was investigated. The starting reagents were microcline, hydromagnesite and chlorine. Non-isothermal and isothermal chlorination assays were carried out in a thermogravimetric device adapted to work in corrosive atmospheres. The temperature effect on potassium extraction and the phase transformations produced during chlorination of microcline were studied. The reagents and reaction products were analyzed by X-ray fluorescence (XRF) and X-ray diffraction (XRD). The experimental results indicated that by chlorination of microcline an important extraction of potassium in the temperature range from 800 to 900 °C was produced. Moreover, at 800 °C the forsterite, enstatite and magnesium aluminate spinel phases were generated.

  1. Boldine action against the stannous chloride effect.

    Science.gov (United States)

    Reiniger, I W; Ribeiro da Silva, C; Felzenszwalb, I; de Mattos, J C; de Oliveira, J F; da Silva Dantas, F J; Bezerra, R J; Caldeira-de-Araújo, A; Bernardo-Filho, M

    1999-12-15

    Peumus boldus extract has been used in popular medicine in the treatment of biliar litiase, hepatic insufficiency and liver congestion. Its effects are associated to the substance boldine that is present in its extract. In the present work, we evaluated the influence of boldine both in: (i) the structural conformation of a plasmid pUC 9.1 through gel electrophoresis analysis; and in (ii) the survival of the strain of Escherichia coli AB1157 submitted to reactive oxygen species (ROS), generated by a Fenton like reaction, induced by stannous chloride. Our results show a reduction of the lethal effect induced by stannous chloride on the survival of the E. coli culture in the presence of boldine. The supercoiled form of the plasmid is not modified by stannous chloride in the presence of boldine. We suggest that the protection induced by boldine could be explained by its anti-oxidant mechanism. In this way, the boldine could be reacting with stannous ions, protecting them against the oxidation and, consequently, avoiding the generation of ROS.

  2. Understanding microwave vessel contamination by chloride species.

    Science.gov (United States)

    Recchia, Sandro; Spanu, Davide; Bianchi, Davide; Dossi, Carlo; Pozzi, Andrea; Monticelli, Damiano

    2016-10-01

    Microwaves are widely used to assist digestion, general sample treatment and synthesis. The use of aqua regia is extensively adopted for the closed vessel mineralization of samples prior to trace element detection, leading to the contamination of microwave vessels by chlorine containing species. The latter are entrapped in the polymeric matrix of the vessels, leading to memory effects that are difficult to remove, among which the risk of silver incomplete recoveries by removal of the sparingly soluble chloride is the predominant one. In the present paper, we determined by mass spectrometry that hydrogen chloride is the species entrapped in the polymeric matrix and responsible for vessel contamination. Moreover, several decontamination treatments were considered to assess their efficiency, demonstrating that several cleaning cycles with water, nitric acid or silver nitrate in nitric acid were inefficient in removing chloride contamination (contamination reduction around 90%). Better results (≈95% decrease) were achieved by a single decontamination step in alkaline environment (sodium hydroxide or ammonia). Finally, a thermal treatment in a common laboratory oven (i.e. without vacuum and ventilation) was tested: a one hour heating at 150°C leads to a 98.5% decontamination, a figure higher than the ones obtained by wet treatments which requires comparable time. The latter treatment is a major advancement with respect to existing treatments as it avoids the need of a vacuum oven for at least 17h as presently proposed in the literature.

  3. Highly brominated anthracenes as precursors for the convenient synthesis of 2,9,10-trisubstituted anthracene derivatives

    Directory of Open Access Journals (Sweden)

    2008-12-01

    Full Text Available When 9,10-dibromoanthracene was treated with bromine in CCl4 without a catalyst, 1,2,3,4,9,10-hexabromo-1,2,3,4-tetrahydroanthracene (3 was obtained in 95% yield in the absence of other stereoisomers or rearomatization products. We investigated the base-induced elimination reaction of hexabromide 3 under various conditions. Pyridine-induced elimination of hexabromide 3 afforded 2,9,10-tribromoanthracene (12 in 75% yield, and tribromide 12 was transformed to trimethoxy compound 13 and trinitrile 14 by copper-assisted nucleophilic substitution reactions.

  4. Neurobehavioral function and low-level exposure to brominated flame retardants in adolescents: a cross-sectional study

    Directory of Open Access Journals (Sweden)

    Kiciński Michał

    2012-11-01

    Full Text Available Abstract Background Animal and in vitro studies demonstrated a neurotoxic potential of brominated flame retardants, a group of chemicals used in many household and commercial products to prevent fire. Although the first reports of detrimental neurobehavioral effects in rodents appeared more than ten years ago, human data are sparse. Methods As a part of a biomonitoring program for environmental health surveillance in Flanders, Belgium, we assessed the neurobehavioral function with the Neurobehavioral Evaluation System (NES-3, and collected blood samples in a group of high school students. Cross-sectional data on 515 adolescents (13.6-17 years of age was available for the analysis. Multiple regression models accounting for potential confounders were used to investigate the associations between biomarkers of internal exposure to brominated flame retardants [serum levels of polybrominated diphenyl ether (PBDE congeners 47, 99, 100, 153, 209, hexabromocyclododecane (HBCD, and tetrabromobisphenol A (TBBPA] and cognitive performance. In addition, we investigated the association between brominated flame retardants and serum levels of FT3, FT4, and TSH. Results A two-fold increase of the sum of serum PBDE’s was associated with a decrease of the number of taps with the preferred-hand in the Finger Tapping test by 5.31 (95% CI: 0.56 to 10.05, p = 0.029. The effects of the individual PBDE congeners on the motor speed were consistent. Serum levels above the level of quantification were associated with an average decrease of FT3 level by 0.18 pg/mL (95% CI: 0.03 to 0.34, p = 0.020 for PBDE-99 and by 0.15 pg/mL (95% CI: 0.004 to 0.29, p = 0.045 for PBDE-100, compared with concentrations below the level of quantification. PBDE-47 level above the level of quantification was associated with an average increase of TSH levels by 10.1% (95% CI: 0.8% to 20.2%, p = 0.033, compared with concentrations below the level of quantification. We did not

  5. Isoquinolinium bromochromate: An efficient and stable reagent for bromination of hydroxylated aromatic compounds and oxidation of alcohols

    Institute of Scientific and Technical Information of China (English)

    Sandeep V. Khansole; Shivaji B. Patwari; Archana Y. Vibhute; Yeshwant B. Vibhute

    2009-01-01

    The new chromium (VI) oxidizing reagent isoquinolinium bromochromate (IQBC) was prepared and characterized. The IQBC has been found to be stable and an efficient solid reagent which can be easily prepared in good yield. It act as an efficient brominating reagent for hydroxylated aromatic compounds as well as good oxidizing reagent for the conversion of alcohols to carbonyl compounds in good to excellent yield. The synthesized isoquinolinium bromochromate is more ideal reagent, with number of specification including: higher yield, mild conditions and easy preparation. The results obtained with isoquinolinium bromochromate are satisfactory and suggest that the reagent has few advantages over the existing chromium (VI) reagents.

  6. Analysis of Causes Leading to High Bromine Number of C8+Aromatics and Short Clay Service Life and Countermeasures Proposed

    Institute of Scientific and Technical Information of China (English)

    Li Yousong; Ni Xiaoliang; Yan Jun

    2007-01-01

    After comparing the operating status of other catalytic reforming units and evaluation of the side-cut stream tests,the refinery investigated the influence of the feedstock property,clay types,and operating regime of the clay tower and catalytic reforming unit on the service life of the clay.Test results had revealed that the low potential aromatic content of the reformer feed and high operating severity were the critical causes leading to high bromine number of the C8+ aromatics feed for the PX unit and the shortened service life of clay.This article also puts forward the corresponding remedial measures.

  7. Slow Phospholipid Exchange between a Detergent-Solubilized Membrane Protein and Lipid-Detergent Mixed Micelles: Brominated Phospholipids as Tools to Follow Its Kinetics

    Science.gov (United States)

    Montigny, Cédric; Dieudonné, Thibaud; Orlowski, Stéphane; Vázquez-Ibar, José Luis; Gauron, Carole; Georgin, Dominique; Lund, Sten; le Maire, Marc; Møller, Jesper V.; Champeil, Philippe

    2017-01-01

    Membrane proteins are largely dependent for their function on the phospholipids present in their immediate environment, and when they are solubilized by detergent for further study, residual phospholipids are critical, too. Here, brominated phosphatidylcholine, a phospholipid which behaves as an unsaturated phosphatidylcholine, was used to reveal the kinetics of phospholipid exchange or transfer from detergent mixed micelles to the environment of a detergent-solubilized membrane protein, the paradigmatic P-type ATPase SERCA1a, in which Trp residues can experience fluorescence quenching by bromine atoms present on phospholipid alkyl chains in their immediate environment. Using dodecylmaltoside as the detergent, exchange of (brominated) phospholipid was found to be much slower than exchange of detergent under the same conditions, and also much slower than membrane solubilization, the latter being evidenced by light scattering changes. The kinetics of this exchange was strongly dependent on temperature. It was also dependent on the total concentration of the mixed micelles, revealing the major role for such exchange of the collision of detergent micelles with the detergent-solubilized protein. Back-transfer of the brominated phospholipid from the solubilized protein to the detergent micelle was much faster if lipid-free DDM micelles instead of mixed micelles were added for triggering dissociation of brominated phosphatidylcholine from the solubilized protein, or in the additional presence of C12E8 detergent during exchange, also emphasizing the role of the chemical nature of the micelle/protein interface. This protocol using brominated lipids appears to be valuable for revealing the possibly slow kinetics of phospholipid transfer to or from detergent-solubilized membrane proteins. Independently, continuous recording of the activity of the protein can also be used in some cases to correlate changes in activity with the exchange of a specific phospholipid, as shown here

  8. OLGA experiments with {sup 261}104 under chlorinating and brominating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Gaeggeler, H.W.; Eichler, B.; Jost, D.T.; Piguet, D.; Tuerler, A. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Buklanov, G.; Lebedev, V.; Timokhin, S.; Vedeev, M.V.; Yakushev, A.; Zvara, I. [FLNR, Dubna (Russian Federation); Huebener, S. [FZR (Germany)

    1997-09-01

    With the On-Line Gas chemistry Apparatus OLGA III the retention times of element 104 chloride and bromide was measured in a quartz column using the isotope {sup 261}104 with a half-life of 78 s. With HCl as chlorinating agent element 104 was found to quantitatively pass through the column at 150{sup o}C, whereas with HBr this temperature shifted to about 300{sup o}C. Under both halogenating conditions, the homologuous element Hf passed through the column at higher temperatures than element 104, in agreement with expectations. (author) 2 figs., 2 refs.

  9. Anti-chloride permeability and anti-chloride corrodibility of a green high performance concrete admixture in concrete

    Institute of Scientific and Technical Information of China (English)

    ZHENG Yongbao; LIU Xinrong; LIU Dongyan; CHEN Jiangong; HUANG Xiongjun

    2003-01-01

    The effects of green high performance concrete (GHPC) admixture on the anti-chloride permeability and anti- chloride corrodibility of concrete are studied by a series of experiments designed on the basis of the diffusion principle and electrochemical principle. The GHPC admixture consists of fly ash, gangue, slag, red mud, etc., of which the mass fraction of industrial residues is over 96 %. The anti-permeabilities and anti-corrodibilities of the tested GHPC and normal concrete (NC) are evaluated by the Diffusion Coefficients of chloride which was obtained by measuring the concentration of chloride in the tested systems by the voltage difference method. It is found that the adoption of GHPC admixture greatly improves the anti-chloride permeability and anti-chloride corrodibility by modifying the inner structure and contracting the porosity of concrete to the reduce considerably the diffusion rate of chloride. The admixture is desirable regarding its engineering performances as well as economical and environmental interests.

  10. Chloride Ingress in Concrete with Different Age at Time of First Chloride Exposure

    DEFF Research Database (Denmark)

    Hansen, Esben Østergaard; Iskau, Martin Riis; Hasholt, Marianne Tange

    2016-01-01

    Concrete structures cast in spring have longer time to hydrate and are therefore denser and more resistant to chloride ingress when first subjected to deicing salts in winter than structures cast in autumn. Consequently, it is expected that a spring casting will have a longer service life....... This hypothesis is investigated in the present study by testing drilled cores from concrete cast in 2012 and 2013 on the Svendborgsund Bridge. The cores are subject to petrographic examination and mapping of chloride profiles. Moreover, chloride migration coefficients have been measured. The study shows...... that the effect of the extra time of hydration obtained when casting in spring increases the expected service life of the concrete structure significantly....

  11. Brominated polyunsaturated lipids from the Chinese sponge Xestospongia testudinaria as a new class of pancreatic lipase inhibitors.

    Science.gov (United States)

    Liang, Lin-Fu; Wang, Ting; Cai, You-Sheng; He, Wen-Fei; Sun, Peng; Li, Yu-Fen; Huang, Qi; Taglialatela-Scafati, Orazio; Wang, He-Yao; Guo, Yue-Wei

    2014-05-22

    Chemical analysis of the Chinese marine sponge Xestospongia testudinaria afforded a library of brominated polyunsaturated lipids including eight new compounds, named xestonarienes A-H (3-10) and thirteen known analogues (11-23). The structures of the new compounds were elucidated by detailed spectroscopic analysis and by comparison with literature data. The isolated lipids were evaluated for their inhibitory activity against pancreatic lipase (PL), an essential enzyme for efficient fat digestion and the major metabolite, 14, exhibited a marked inhibitory activity (IC50 = 3.11 μM), similar to that of the positive control Orlistat (IC50 = 0.78 μM). The preliminary structure-activity relationships on the series of compounds clearly evidenced that a terminal (E)-enyne functionality, a diyne within the chain, and methyl ester group are all key functional groups for the activity of this class of PL inhibitors. Further biological investigation on compound 14 revealed a significant decrease in the plasma triglyceride level following an oral lipid challenge in C57BLKS/J male mice. Acute toxicology study demonstrated that compound 14 was non-toxic up to 1600 mg/kg p.o in mice. This is the first report of the PL inhibitory activity for brominated polyunsaturated lipids and the obtained results qualify compound 14 as a potent and bioavailable drug candidate for a mild and safe treatment to prevent and reduce obesity.

  12. BROMINATION OF 4-VINYLCYCLOHEXANE AND APPLYING THE RESULTING PRODUCT TO IMPROVE THE FLAME RETARDANT PROPERTIES OF WOOD

    Directory of Open Access Journals (Sweden)

    N. S. Nikulina

    2014-01-01

    Full Text Available Currently, the demand for timber is increasing. Wood and products on its basis are considered to be the most popular in the construction industry, furniture industry, as building materials and other However, along with the positive features of this material there are also negative factors, which include low resistance to biological degradation, high temperature, resistance. Wood and materials based on it are the most flammable, and fire safety is characterized by the velocity of propagation of fire on the wooden structure. He is able to destroy it in a matter of minutes. So the wooden house elements must be protected from fire. It was therefore necessary for the fire protection of wood. It is in the handling of wood with flame retardants. Basic fire fighting methods is the impregnation of wood antipyrene composition, painting fire paint and constructive ways - insulation of timber, non-combustible compositions which can resist the fire. In the work of brominated 4-vinylcyclohexane formed as a by-product in the petrochemical industry, in chloroform synthesized compound with bromine 62-64 % and the possibility of using this product to get antiferromag composition. It is established that the application for the protective treatment of wood synthesized flame retardant has shown that this product can be used for the protective treatment of natural wood to make it flame retardant properties. Use as antiperiodic compositions bromodomain based products 4-vinylcyclohexane allows to obtain images of wood first group of flame retardant efficiency.

  13. An efficient and fast analytical procedure for the bromine determination in waste electrical and electronic equipment plastics.

    Science.gov (United States)

    Taurino, R; Cannio, M; Mafredini, T; Pozzi, P

    2014-01-01

    In this study, X-ray fluorescence (XRF) spectroscopy was used, in combination with micro-Raman spectroscopy, for a fast determination of bromine concentration and then of brominated flame retardants (BFRs) compounds in waste electrical and electronic equipments. Different samples from different recycling industries were characterized to evaluate the sorting performances of treatment companies. This investigation must be considered of prime research interest since the impact of BFRs on the environment and their potential risk on human health is an actual concern. Indeed, the new European Restriction of Hazardous Substances Directive (RoHS 2011/65/EU) demands that plastics with BFRs concentration above 0.1%, being potential health hazards, are identified and eliminated from the recycling process. Our results show the capability and the potential of Raman spectroscopy, together with XRF analysis, as effective tools for the rapid detection of BFRs in plastic materials. In particular, the use of these two techniques in combination can be considered as a promising method suitable for quality control applications in the recycling industry.

  14. On-line detection of heavy metals and brominated flame retardants in technical polymers with laser-induced breakdown spectrometry

    Science.gov (United States)

    Stepputat, Michael; Noll, Reinhard

    2003-10-01

    The use of laser-induced breakdown spectrometry (LIBS) for the analysis of heavy metals and brominated flame retardants in end-of-life waste electric and electronic equipment (EOL-WEEE) pieces is investigated. Single- and double-pulse plasma excitation as well as the influence of detection parameters is studied to yield a parameter field with improved sensitivity and limits of detection. A LIBS analyzer was set up as an on-line measuring unit to detect heavy metals and brominated flame retardants in moving EOL-WEEE pieces in an automatic sorting line. An autofocusing unit with an adjustment range of 50 mm was incorporated to permit measurements of objects that pass by a LIBS analyzer with their surfaces at various distances from it. Tests with EOL-WEEE monitor housings on the conveyor belt of a pilot sorting system successfully demonstrated the capability of the LIBS analyzer to quantify the concentration of hazardous elements in real waste EOL-WEEE pieces.

  15. Study of the transference rules for bromine in waste printed circuit boards during microwave-induced pyrolysis.

    Science.gov (United States)

    Sun, Jing; Wang, Wenlong; Liu, Zhen; Ma, Chunyuan

    2011-05-01

    The production of waste printed circuit boards (WPCBs) has drawn increasing global concern, especially because the high bromine (Br) content (5-15%) places obstacles in the way of simple disposal techniques. Microwave-induced pyrolysis of WPCBs provides a promising way to dispose of these hazardous and resource-filled wastes. The transference rules for Br during microwave-induced pyrolysis have been investigated experimentally. It was found that the microwave energy could be used more efficiently to accelerate the heating rate and improve the final pyrolysis temperature by adding some activated carbon (AC) as microwave absorbents. The high temperature and rapid pyrolysis process promoted the yields of gaseous products and the decomposition of brominated compounds into hydrogen bromide and then benefited the capture of Br and the debromination of byproducts. The application of a calcium carbonate (CaCO3) layer overhead led to over 95% debromination of the liquid products and over 50% capture of the total Br. It can be concluded that the presented method is suitable for the control of Br transference in the recycling of WPCBs. This method can also be extended to the disposal of the electronic scraps.

  16. Bromination of graphene: a new route to making high performance transparent conducting electrodes with low optical losses

    KAUST Repository

    Mansour, Ahmed

    2015-09-03

    The high optical transmittance, electrical conductivity, flexibility and chemical stability of graphene have triggered great interest in its application as a transparent conducting electrode material and as a potential replacement for indium doped tin oxide. However, currently available large scale production methods such as chemical vapor deposition produce polycrystalline graphene, and require additional transfer process which further introduces defects and impurities resulting in a significant increase in its sheet resistance. Doping of graphene with foreign atoms has been a popular route for reducing its sheet resistance which typically comes at a significant loss in optical transmission. Herein, we report the successful bromine doping of graphene resulting in air-stable transparent conducting electrodes with up to 80% reduction of sheet resistance reaching ~180 Ω/ at the cost of 2-3% loss of optical transmission in case of few layer graphene and 0.8% in case of single layer graphene. The remarkably low tradeoff in optical transparency leads to the highest enhancements in figure of merit reported thus far. Furthermore, our results show a controlled increase in the workfunction up to 0.3 eV with the bromine content. These results should help pave the way for further development of graphene as potentially a highly transparent substitute to other transparent conducting electrodes in optoelectronic devices.

  17. HPLC-ED of low-molecular weight brominated phenols and tetrabromobisphenol A using pretreated carbon fiber microelectrode.

    Science.gov (United States)

    Bartosova, Zdenka; Jirovsky, David; Riman, Daniel; Halouzka, Vladimir; Svidrnoch, Martin; Hrbac, Jan

    2014-05-01

    Electrochemically pretreated carbon fiber microelectrode was used to develop a simple, fast and sensitive HPLC-ECD method for the determination of brominated phenols. In addition to simple mono-, di- and tri-bromophenols (4-bromophenol, 2,4-dibromophenol, 2,6-dibromophenol, 2,4,6-tri-bromophenol) the possibility of electrochemical detection of 3,3',5,5'-tetrabromobisphenol A in oxidation mode is reported for the first time. The isocratic separation was achieved within 14 min using ternary mobile phase consisting of 50mM-phosphate buffer (pH 3.5), acetonitrile and methanol (35/15/50, v/v), and detection potential of E=+1450 mV (vs. Ag/AgCl). The carbon fiber microelectrode permitted to use high anodic potentials (up to +1800 mV vs. Ag/AgCl), the optimum analytical response was achieved at +1450 mV vs. Ag/AgCl. The limits of detection (LOD) for the studied analytes were within the range of 1.8-56.6 ng mL(-1). The developed method was applied to determination of brominated phenols in spiked water samples. Furthermore, after simple extraction with methyl tert-butyl ether, it was possible to quantify tetrabromobisphenol A (TBBA) in a piece of CRT monitor plastic casing. The found amount of TBBA was 10.22 mg kg(-1) (±0.43).

  18. Measurement-based modelling of bromine-induced oxidation of mercury above the Dead Sea

    Science.gov (United States)

    Tas, E.; Obrist, D.; Peleg, M.; Matveev, V.; Faïn, X.; Asaf, D.; Luria, M.

    2012-03-01

    Atmospheric mercury depletion events (AMDEs) outside the polar region - driven by high levels of gaseous Br and BrO (i.e., BrOx) - were observed recently in the warm Dead Sea boundary layer. The efficient oxidation of gaseous elemental mercury (GEM) under temperate conditions by BrOx was unexpected considering that the thermal back dissociation reaction of HgBr is about 2.5 orders of magnitude higher under Dead Sea temperatures compared to polar temperatures, and hence was expected to significantly slow down GEM oxidation under warm temperatures. The goal of this modelling study was to improve understanding of the interaction of reactive bromine and mercury during Dead Sea AMDEs using numerical simulations based on a comprehensive measurement campaign in summer 2009. Our analysis is focused on daytime AMDE when chemical processes dominate concentration changes. Best agreements between simulations and observations were achieved using rate constants for kHg+Br and kHg+BrO of 2.7 × 10-13 cm3 molecule-1 s-1 and 1.5 × 10-13 cm3 molecule-1 s-1, respectively. Our model also predicted that a rate constant kHg+BrO of 5.0 × 10-14 cm3 molecule-1 s-1 may be considered as a minimum, which is higher than most reported values. These rate constants suggest that BrO could be a more efficient oxidant than Br in the troposphere as long as [Br]/[BrO] ratios are smaller than ~0.2 to 0.5. Under Dead Sea conditions, these kinetics demonstrate a high efficiency and central role of BrOx for AMDEs, with relative contributions to GEM depletion of more than ~90%. Unexpectedly, BrO was found to be the dominant oxidant with relative contributions above 80%. The strong contribution of BrO could explain why the efficiency of GEM oxidation at the Dead Sea does not critically depend on Br and, therefore, is comparable to that in cold polar regions. In order to confirm the suggested kinetics, additional studies, particularly for temperature-dependence of rate constants, are required.

  19. Tracing organophosphorus and brominated flame retardants and plasticizers in an estuarine food web.

    Science.gov (United States)

    Brandsma, Sicco H; Leonards, Pim E G; Leslie, Heather A; de Boer, Jacob

    2015-02-01

    Nine organophosphorus flame retardants (PFRs) were detected in a pelagic and benthic food web of the Western Scheldt estuary, The Netherlands. Concentrations of several PFRs were an order of magnitude higher than those of the brominated flame retardants (BFRs). However, the detection frequency of the PFRs (6-56%) was lower than that of the BFRs (50-97%). Tris(2-butoxyethyl) phosphate (TBOEP), tris(isobutyl) phosphate (TIBP) and tris(2-chloroisopropyl) phosphate (TCIPP) were the dominant PFRs in sediment with median concentrations of 7.0, 8.1 and 1.8 ng/g dry weight (dw), respectively. PFR levels in the suspended particular matter (SPM) were 2-12 times higher than that in sediment. TBOEP, TCIPP, TIBP, tris(2-chloroethyl) phosphate (TCEP) and tris(phenyl) phosphate (TPHP) were found in organisms higher in the estuarine food web. The highest PFR concentrations in the benthic food web were found in sculpin, goby and lugworm with median concentrations of 17, 7.4, 4.6 and 2.0 ng/g wet weight (ww) for TBOEP, TIBP, TCIPP and TPHP, respectively. Comparable levels were observed in the pelagic food web, BDE209 was the predominant PBDE in sediment and SPM with median concentrations up to 9.7 and 385 ng/g dw, respectively. BDE47 was predominant in the biotic compartment of the food web with highest median levels observed in sculpin and common tern eggs of 79 ng/g lipid weight (lw) (2.5 ng/g ww) and 80 ng/g lw (11 ng/g ww), respectively. Trophic magnification was observed for all PBDEs with the exception of BDE209. Indications of trophic magnification of PFRs were observed in the benthic food web for TBOEP, TCIPP and TCEP with tentative trophic magnification factors of 3.5, 2.2 and 2.6, respectively (pwebs. The relative high PFR levels in several fish species suggest high emissions and substantial exposure of organisms to PFRs in the Western Scheldt.

  20. Measurement-based modelling of bromine-induced oxidation of mercury above the Dead Sea

    Directory of Open Access Journals (Sweden)

    E. Tas

    2012-03-01

    Full Text Available Atmospheric mercury depletion events (AMDEs outside the polar region – driven by high levels of gaseous Br and BrO (i.e., BrOx – were observed recently in the warm Dead Sea boundary layer. The efficient oxidation of gaseous elemental mercury (GEM under temperate conditions by BrOx was unexpected considering that the thermal back dissociation reaction of HgBr is about 2.5 orders of magnitude higher under Dead Sea temperatures compared to polar temperatures, and hence was expected to significantly slow down GEM oxidation under warm temperatures. The goal of this modelling study was to improve understanding of the interaction of reactive bromine and mercury during Dead Sea AMDEs using numerical simulations based on a comprehensive measurement campaign in summer 2009.

    Our analysis is focused on daytime AMDE when chemical processes dominate concentration changes. Best agreements between simulations and observations were achieved using rate constants for kHg+Br and kHg+BrO of 2.7 × 10−13 cm3 molecule−1 s−1 and 1.5 × 10−13 cm3 molecule−1 s−1, respectively. Our model also predicted that a rate constant kHg+BrO of 5.0 × 10−14 cm3 molecule−1 s−1 may be considered as a minimum, which is higher than most reported values. These rate constants suggest that BrO could be a more efficient oxidant than Br in the troposphere as long as [Br]/[BrO] ratios are smaller than ~0.2 to 0.5. Under Dead Sea conditions, these kinetics demonstrate a high efficiency and central role of BrOx for AMDEs, with relative contributions to GEM depletion of more than ~90%. Unexpectedly, BrO was found to be the dominant oxidant with relative contributions above 80%. The strong contribution of BrO could explain why the efficiency of GEM

  1. Selective pressurized liquid extraction of replacement and legacy brominated flame retardants from soil.

    Science.gov (United States)

    McGrath, Thomas J; Morrison, Paul D; Ball, Andrew S; Clarke, Bradley O

    2016-08-05

    Polybrominated diphenyl ethers (PBDEs) are a class of flame retardant registered as UN POPs due to their persistence in the environment, bioaccumulation potential and toxicity. Replacement novel brominated flame retardants (NBFRs) have exhibited similar health hazards and environmental distribution, becoming recognized as significant contaminants. This work describes the development and validation of a sensitive and reliable method for the simultaneous quantitation of PBDEs and NBFRs in environmental soil samples using selective pressurized liquid extraction (S-PLE) and gas chromatography coupled to triple quadrupole mass spectrometry (GC-(EI)-MS/MS). Under optimal conditions, extraction of eight PBDEs (-28, -47, -99, -100, -153, -154, -183 and -209) and five NBFRs; pentabromotoluene (PBT), pentabromoethylbenzene (PBEB), hexabromobenzene (HBB), 2-ethylhexyl-2,3,4,5-tetrabromobenzoate (EH-TBB) and bis(2,4,6-tribromophenoxy)ethane (BTBPE) was performed at 100°C and 1500psi using a 1:1 mixture of hexane and dichloromethane. The method utilized 33mL capacity PLE cells containing, from bottom to top, a single cellulose filter, 3g activated Florisil, 6g acid silica (10% w/w), 3g Na2SO4, another cellulose filter, 2g activated copper powder and 3g soil sample dispersed in 2g Na2SO4 and 1g of Hydromatrix. The method was evaluated by repeated extraction and analysis of all analytes from 3g soil at three spike concentrations. Good recoveries were observed for most analytes at each of the spiking levels with RSD values generally below 20%. MDLs ranged from 0.01 to 4.8ng/g dw for PBDEs and 0.01-0.55ng/g dw for NBFRs. The described one-step combined extraction and cleanup method reduces sample processing times compared with traditional procedures, while delivering comparable analytical performance. The method was successfully applied to environmental soil samples (n=5), detecting PBDEs in each sample and providing the first account of NBFR contamination in Australian soils.

  2. Heterogeneous nano-Fe/Ca/CaO catalytic ozonation for selective surface hydrophilization of plastics containing brominated and chlorinated flame retardants (B/CFRs): separation from automobile shredder residue by froth flotation.

    Science.gov (United States)

    Mallampati, Srinivasa Reddy; Lee, Byoung Ho; Mitoma, Yoshiharu; Simion, Cristian

    2016-12-09

    One method of weakening the inherently hydrophobic surface of plastics relevant to flotation separation is heterogeneous nano-Fe/Ca/CaO catalytic ozonation. Nano-Fe/Ca/CaO-catalyzed ozonation for 15 min efficiently decreases the surface hydrophobicity of brominated and chlorinated flame retardant (B/CFR)-containing plastics (such as acrylonitrile-butadienestyrene (ABS), high-impact polystyrene (HIPS), and polyvinyl chloride (PVC)) in automobile shredder residue (ASR) to such an extent that their flotation ability is entirely depressed. Such a hydrophilization treatment also stimulates the ABS, HIPS, and PVC surface roughness, wetting of the surface, and the thermodynamic equilibrium conditions at the surface and ultimately changes surface polarity. SEM-EDS, AFM, and XPS analyses of the PVC and ABS surfaces demonstrated a marked decrease in [Cl/Br] and a significant increase in the number of hydrophilic groups, such as C-O, C=O, and (C=O)-O. Under froth flotation conditions at 50 rpm, about 99.5 % of ABS and 99.5 % of HIPS in ASR samples settled out, resulting in a purity of 98 and 98.5 % for ABS and HIPS in ASR samples, respectively. Furthermore, at 150 rpm, we also obtained 100 % PVC separation in the settled fraction, with 98 % purity in ASR. Total recovery of non-B/CFR-containing plastics reached nearly 100 % in the floating fraction. The amount of nano-Fe/Ca/CaO reagent employed during ozonation is very small, and additional removal of surface contaminants from the recycled ASR plastic surfaces by ozonation makes the developed process simpler, greener, and more effective.

  3. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    Directory of Open Access Journals (Sweden)

    Ekrem Güler

    2011-06-01

    Full Text Available Benzalkonium chloride (BAC is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is to draw attention to the fact that BAC application to the scalp for treating pediculosis capitis may resemble the herpes encephalitis clinical picture.

  4. N-(2-Benzoylethylpropan-2-aminium chloride

    Directory of Open Access Journals (Sweden)

    Abdullah Aydın

    2012-09-01

    Full Text Available In the title salt, C12H18NO+·Cl−, N—H...Cl interactions between the free chloride anions and the organic cations connect the molecules into hydrogen-bond dimers, forming a R22(8 motif. The dimers are linked by C—H...O hydrogen bonds into chains extending along [301]. The carbonyl group is co-planar with the phenyl ring [C—C—C=O torsion angle = −3.3 (7°]. The side chain has an E conformation.

  5. Oral cadmium chloride intoxication in mice

    DEFF Research Database (Denmark)

    Andersen, O; Nielsen, J B; Svendsen, P

    1988-01-01

    Diethyldithiocarbamate (DDC) is known to alleviate acute toxicity due to injection of cadmium salts. However, when cadmium chloride was administered by the oral route, DDC enhanced rather than alleviated the acute toxicity; both oral and intraperitoneal (i.p.) administration of DDC had this effect....... Thus, orally administered DDC enhanced cadmium-induced duodenal and ileal tissue damage and inhibition of peristalsis, as indicated by an increased intestinal transit time. At low cadmium doses, the whole-body retention of cadmium was increased by oral DDC administration. Intraperitoneally administered...

  6. Synthesis of Aminolaurylpyridinium Chloride as Antimicrobial Agent

    Institute of Scientific and Technical Information of China (English)

    ZHAO Tao; SONG Xin-yuan; SUN Gang

    2008-01-01

    4-amino-laurylpyridinium chloride (ALPC) was synthesized and employed in antimicrobial finishing of wool fabrics. The structures of the salt was fully characterized by using FTIR, 1 H-NMR and 13 C-NMR analysis. The effects of pH conditions of finishing baths, finishing time and temperature, and salt concentrations were investigated. ALPC could form ionic interactions with anionic groups on wool, which contribute to durable antimicrobial functions. The finished wool fabrics exhibited antimicrobial efficacy against Escherichia coli. The washing durability of antimicrobial functions on the finished wool fabrics was also studied.

  7. Magnesium anode for chloride ion batteries.

    Science.gov (United States)

    Zhao, Xiangyu; Li, Qiang; Zhao-Karger, Zhirong; Gao, Ping; Fink, Karin; Shen, Xiaodong; Fichtner, Maximilian

    2014-07-23

    A key advantage of chloride ion battery (CIB) is its possibility to use abundant electrode materials that are different from those in Li ion batteries. Mg anode is presented as such a material for the first time and Mg/C composite prepared by ball milling of Mg and carbon black powders or thermally decomposed MgH2/C composite has been tested as anode for CIB. The electrochemical performance of FeOCl/Mg and BiOCl/Mg was investigated, demonstrating the feasibility of using Mg as anode.

  8. Chloride diffusion in partially saturated cementitious material

    DEFF Research Database (Denmark)

    Nielsen, Erik Pram; Geiker, Mette Rica

    2003-01-01

    The paper proposes a combined application of composite theory and Powers' model for microstructural development for the estimation of the diffusion coefficient as a function of the moisture content of a defect-free cementitious material. Measurements of chloride diffusion in mortar samples (440 kg....../m(3) rapid-hardening Portland cement, w/c = 0.5, maturity minimum 6 months) stored at 65% and 85% RH, as well as in vacuum-saturated mortar samples, illustrate the applicability of the method. (C) 2003 Elsevier Science Ltd. All rights reserved....

  9. Chloride regulates afferent arteriolar contraction in response to depolarization

    DEFF Research Database (Denmark)

    Hansen, P B; Jensen, B L; Skott, O

    1998-01-01

    . The results show that K+-induced contraction of smooth muscle cells in the afferent arteriole is highly sensitive to chloride, whereas neurotransmitter release and ensuing contraction is not dependent on chloride. Thus, there are different activation pathways for depolarizing vasoconstrictors......-Renal vascular reactivity is influenced by the level of dietary salt intake. Recent in vitro data suggest that afferent arteriolar contractility is modulated by extracellular chloride. In the present study, we assessed the influence of chloride on K+-induced contraction in isolated perfused rabbit...... afferent arterioles. In 70% of vessels examined, K+-induced contraction was abolished by acute substitution of bath chloride. Consecutive addition of Cl- (30, 60, 80, 100, 110, and 117 mmol/L) restored the sensitivity to K+, and half-maximal response was observed at 82 mmol/L chloride. The calcium channel...

  10. Investigation of Lithium-Thionyl Chloride Battery Safety Hazards.

    Science.gov (United States)

    1983-01-01

    LITHIUM - THIONYL CHLORIDE BATTERY SAFETY HAZARDS(U) GOULD RESEARCH CENTER ROLLING MEADOWS IL MATERIALS LAB A I ATTIA ET...838-012 7 ontract No. 60921-81-C-0363 6// Investigation of Lithium - Thionyl Chloride Battery Safety Hazards AD A 1 T 2 , Alan I. Attia Gould Research...REPORT & PERIOD COVERED Investigation of Lithium - Thionyl Chloride Final Report Battery Safety Hazards 9/28/81 - 12/31/82 6. PERFORMING ORG. REPORT

  11. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    OpenAIRE

    Jun Liu; Kaifeng Tang; Dong Pan; Zongru Lei; Weilun Wang; Feng Xing

    2014-01-01

    Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions...

  12. Chloride ingress profiles measured by electron probe micro analysis

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, O.M. [Univ. of Aberdeen (United Kingdom). Dept. of Chemistry]|[Technical Univ. of Denmark, Lyngby (Denmark). Dept. of Structural Engineering and Materials; Coats, A.M.; Glasser, F.P. [Univ. of Aberdeen (United Kingdom). Dept. of Chemistry

    1996-11-01

    Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA is demonstrated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA.

  13. Chloride ingress profiles measured by electron probe micro analysis

    DEFF Research Database (Denmark)

    Jensen, Ole mejlhede; Coats, Alison M.; Glasser, Fred P.

    1996-01-01

    Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA...... is demonstated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA. Copyright (C) 1996 Elsevier Science Ltd...

  14. On barium oxide solubility in barium-containing chloride melts

    Energy Technology Data Exchange (ETDEWEB)

    Nikolaeva, Elena V.; Zakiryanova, Irina D.; Bovet, Andrey L.; Korzun, Iraida V. [Ural Federal Univ., Yekaterinburg (Russian Federation). Inst. of High Temperature Electrochemistry

    2016-11-01

    Oxide solubility in chloride melts depends on temperature and composition of molten solvent. The solubility of barium oxide in the solvents with barium chloride content is essentially higher than that in molten alkali chlorides. Spectral data demonstrate the existence of oxychloride ionic groupings in such melts. This work presents the results of the BaO solubility in two molten BaCl{sub 2}-NaCl systems with different barium chloride content. The received data together with earlier published results revealed the main regularities of BaO solubility in molten BaO-BaCl{sub 2}-MCl systems.

  15. Stochastic modeling of reinforced concrete structures exposed to chloride attack

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Frier, Christian

    2004-01-01

    the reinforcement exceeds a critical threshold value. In the present paper a stochastic model is described by which the chloride content in a reinforced concrete structure can be estimated. The chloride ingress is modeled by a 2-dimensional diffusion process and the diffusion coefficient, surface chloride......For many reinforced concrete structures corrosion of reinforcement is an important problem since it can result in expensive maintenance and repair actions. Further, a significant reduction of the load-bearing capacity can occur. One mode of corrosion initiation is that the chloride content around...

  16. Fire's effect on chloride ingress related durability of concrete structure

    Institute of Scientific and Technical Information of China (English)

    JIN Wei-liang; ZHANG Yi

    2007-01-01

    This paper describes the effects of fire on durability of reinforced concrete structures, and points out that fire not only damages the chemical composition and physical structure of concrete by high temperature, but also leads to an additional risk due to the generation of polyvinyl chloride (PVC)combustion gases. A mathematical model is proposed to calculate chloride ingress profiles in fire damaged concrete, so as to explore the service life prediction of the structure. Rapid Chloride Migration (RCM) test was carried out to determine the chloride diffusion coefficients for the application of the mathematical model. Finally, the detected results of a reported case testified to the validity of the mathematical model.

  17. Catalytic Conversion of Cellulose to Levulinic Acid by Metal Chlorides

    Directory of Open Access Journals (Sweden)

    Beixiao Zhang

    2010-08-01

    Full Text Available The catalytic performance of various metal chlorides in the conversion of cellulose to levulinic acid in liquid water at high temperatures was investigated. The effects of reaction parameters on the yield of levulinic acid were also explored. The results showed that alkali and alkaline earth metal chlorides were not effective in conversion of cellulose, while transition metal chlorides, especially CrCl3, FeCl3 and CuCl2 and a group IIIA metal chloride (AlCl3, exhibited high catalytic activity. The catalytic performance was correlated with the acidity of the reaction system due to the addition of the metal chlorides, but more dependent on the type of metal chloride. Among those metal chlorides, chromium chloride was found to be exceptionally effective for the conversion of cellulose to levulinic acid, affording an optimum yield of 67 mol % after a reaction time of 180 min, at 200 °C, with a catalyst dosage of 0.02 M and substrate concentration of 50 wt %. Chromium metal, most of which was present in its oxide form in the solid sample and only a small part in solution as Cr3+ ion, can be easily separated from the resulting product mixture and recycled. Finally, a plausible reaction scheme for the chromium chloride catalyzed conversion of cellulose in water was proposed.

  18. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    Directory of Open Access Journals (Sweden)

    Jun Liu

    2014-09-01

    Full Text Available Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions are immersed in NaCl solution with a mass concentration of 5%, to simulate the shallow immersion condition in sea water, and the surface chloride concentrations are measured at different ages. It is found that the surface chloride concentration increases following the increasing immersion durations, and varies from a weight percentage of 0.161%–0.781% in concretes with different mix proportions. The w/c (water-to-cement ratio influences the surface chloride concentration significantly, and the higher the w/c is, the higher the surface chloride concentration will be, at the same age. However, following the prolonging of immersion duration, the difference in surface chloride concentration induced by w/c becomes smaller and smaller. The incorporation of fly ash leads to higher surface chloride concentration. The phenomena are explained based on pore structure analyses.

  19. Interpretation of postmortem vitreous concentrations of sodium and chloride.

    Science.gov (United States)

    Zilg, B; Alkass, K; Berg, S; Druid, H

    2016-06-01

    Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time.

  20. Durability of cracked fibre reinforced concrete structures exposed to chlorides

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Ekman, Tom; Hansen, Kurt Kielsgaard

    1999-01-01

    is used as environmental load. The chloride penetration is characterized both qualitatively (UV-test) and quantitatively (chloride profile) and by microscopy. The test programme involves three different concrete qualities. Both steel fibres and polypropylene fibres are used in the concrete beams as well......Durability studies are carried out by subjecting FRC-beams to combined mechanical and environmental load. Mechanical load is obtained by exposing beams to 4-point bending until a predefined crack width is reached, using a newly developed test setup. Exposure to a concentrated chloride solution...... as main reinforcement. The effect of the cracks, the fibres and the concrete quality on the chloride penetration is studied....

  1. Biotransformation of brominated flame retardants into potentially endocrine-disrupting metabolites, with special attention to 2,2 ',4,4 '-tetrabromodiphenyl ether (BDE-47)

    NARCIS (Netherlands)

    Hamers, T.; Kamstra, J.H.; Sonneveld, E.; Murk, A.J.; Visser, T.J.; Velzen, van M.J.M.; Brouwer, A.; Bergman, A.

    2008-01-01

    In this study, the endocrine-disrupting (ED) potency of metabolites from brominated flame retardants (BFRs) was determined. Metabolites were obtained by incubating single-parent compound BFRs with phenobarbital-induced rat liver microsomes. Incubation extracts were tested in seven in vitro bioassays

  2. Brominated flame retardants in fish and shellfish - levels and contribution of fish consumption to dietary exposure of Dutch citizens to HBCD

    NARCIS (Netherlands)

    Leeuwen, van S.P.J.; Boer, de J.

    2008-01-01

    In order to determine the contamination with brominated flame retardants (BFR) in fish regularly consumed by Dutch citizens, 44 samples of freshwater fish, marine fish, and shellfish were analyzed for polybrominated diphenyl ethers (PBDE), tetrabromobisphenol-A (TBBP-A) and its methylated derivative

  3. A comparison of the in vitro cyto- and neurotoxicity of brominated and halogen-free flame retardants : prioritization in search for safe(r) alternatives

    NARCIS (Netherlands)

    Hendriks, Hester S; Meijer, Marieke; Muilwijk, Mirthe; van den Berg, Martin; Westerink, Remco H S

    2014-01-01

    Brominated flame retardants (BFRs) are abundant persistent organic pollutants with well-studied toxicity. The toxicological and ecological concerns associated with BFRs argue for replacement by safe(r) alternatives. Though previous research identified the nervous system as a sensitive target organ f

  4. Formation of brominated disinfection byproducts from natural organic matter isolates and model compounds in a sulfate radical-based oxidation process

    KAUST Repository

    Wang, Yuru

    2014-12-16

    A sulfate radical-based advanced oxidation process (SR-AOP) has received increasing application interest for the removal of water/wastewater contaminants. However, limited knowledge is available on its side effects. This study investigated the side effects in terms of the production of total organic bromine (TOBr) and brominated disinfection byproducts (Br-DBPs) in the presence of bromide ion and organic matter in water. Sulfate radical was generated by heterogeneous catalytic activation of peroxymonosulfate. Isolated natural organic matter (NOM) fractions as well as low molecular weight (LMW) compounds were used as model organic matter. Considerable amounts of TOBr were produced by SR-AOP, where bromoform (TBM) and dibromoacetic acid (DBAA) were identified as dominant Br-DBPs. In general, SR-AOP favored the formation of DBAA, which is quite distinct from bromination with HOBr/OBr- (more TBM production). SR-AOP experimental results indicate that bromine incorporation is distributed among both hydrophobic and hydrophilic NOM fractions. Studies on model precursors reveal that LMW acids are reactive TBM precursors (citric acid > succinic acid > pyruvic acid > maleic acid). High DBAA formation from citric acid, aspartic acid, and asparagine was observed; meanwhile aspartic acid and asparagine were the major precursors of dibromoacetonitrile and dibromoacetamide, respectively.

  5. Exposure to brominated flame retardants, perfluorinated compounds, phthalates and phenols in European birth cohorts: ENRIECO evaluation, first human biomonitoring results, and recommendations

    NARCIS (Netherlands)

    Casas, M.; Chevrier, C.; Hond, E.D.; Fernandez, M.F.; Pierik, F.; Philippat, C.; Slama, R.; Toft, G.; Vandentorren, S.; Wilhelm, M.; Vrijheid, M.

    2013-01-01

    There are emerging concerns about potential effects on child health and development of early-life exposure to substances such as brominated flame retardants (BFRs), perfluorinated compounds (PFCs), phthalates and phenols (including bisphenol A (BPA)); pregnancy and birth cohort studies are ideally d

  6. The DELTA 181 lithium thionyl chloride battery

    Science.gov (United States)

    Sullivan, Ralph M.; Brown, Lawrence E.; Leigh, A. P.

    In 1986, the Johns Hopkins University/Applied Physics Laboratory (JHU/APL) undertook the development of a sensor module for the DELTA 181 spacecraft, a low earth orbit (LEO) mission of less than two months duration. A large lithium thionyl chloride battery was developed as the spacecraft's primary power source, the first known such use for this technology. The exceptionally high energy density of the lithium thionyl chloride cell was the primary driver for its use, resulting in a completed battery with a specific energy density of 120 Wh/lb. Safety requirements became the primary driver shaping all aspects of the power system design and development due to concerns about the potential hazards of this relatively new, high-energy technology. However, the program was completed without incident. The spacecraft was launched on February 8, 1988, from Kennedy Space Center (KSC) with over 60,000 Wh of battery energy. It reentered on April 2, 1988, still operating after 55 days, providing a successful, practical, and visible demonstration of the use of this technology for spacecraft applications.

  7. Regulated trafficking of the CFTR chloride channel.

    Science.gov (United States)

    Kleizen, B; Braakman, I; de Jonge, H R

    2000-08-01

    The cystic fibrosis transmembrane conductance regulator (CFTR), the ABC transporter encoded by the cystic fibrosis gene, is localized in the apical membrane of epithelial cells where it functions as a cyclic AMP-regulated chloride channel and as a regulator of other ion channels and transporters. Whereas a key role of cAMP-dependent phosphorylation in CFTR-channel gating has been firmly established, more recent studies have provided clear evidence for the existence of a second level of cAMP regulation, i.e. the exocytotic recruitment of CFFR to the plasma membrane and its endocytotic retrieval. Regulated trafficking of the CFTR Cl- channel has sofar been demonstrated only in a subset of CFTR-expressing cell types. However, with the introduction of more sensitive methods to measure CFTR cycling and submembrane localization, it might turn out to be a more general phenomenon that could contribute importantly to both the regulation of CFTR-mediated chloride transport itself and to the regulation of other transporters and CFTR-modulated cellular functions. This review aims to summarize the present state of knowledge regarding polarized and regulated CFTR trafficking and endosomal recycling in epithelial cells, to discuss present gaps in our understanding of these processes at the cellular and molecular level, and to consider its possible implications for cystic fibrosis.

  8. Synthesis and structure characterization of diethyldiallylammonium chloride

    Institute of Scientific and Technical Information of China (English)

    刘立华; 龚竹青; 郑雅杰

    2003-01-01

    The unsaturated quaternary ammonium salt diethyldiallylammonium chloride(DEDAAC) was synthesized in a two-step synthetic method. The influences of the adding method of raw materials and temperature on the yields of diethylallylamine (DEAA), and drying and temperature on the synthesis of DEDAAC were investigated. The content of in-process product DEAA was determined by non-aqueous titration. The structure of product DEDAAC was identified with IR, 1 H NMR and elemental analysis. The results show that adding allyl chloride and sodium hydroxide alternately can increase the yield of DEAA and decrease by-products. In further synthesizing of DEDAAC from DEAA, the step of drying DEAA is very necessary. When DEAA is dried by solid sodium hydroxide, good columnar crystals with a high purity(mp 199.5-201.0 ℃) are obtained; when DEAA is undried or the content of water in DEAA is above 20%, only platelets with bad quality are obtained even without crystals. The suitable synthesis conditions for DEAA and DEDAAC are 35 ℃, 6 h and 40 ℃, 36 h, respectively, and their yields are 69.7% and 67.3%, respectively.

  9. Fault locator of an allyl chloride plant

    Directory of Open Access Journals (Sweden)

    Savković-Stevanović Jelenka B.

    2004-01-01

    Full Text Available Process safety analysis, which includes qualitative fault event identification, the relative frequency and event probability functions, as well as consequence analysis, was performed on an allye chloride plant. An event tree for fault diagnosis and cognitive reliability analysis, as well as a troubleshooting system, were developed. Fuzzy inductive reasoning illustrated the advantages compared to crisp inductive reasoning. A qualitative model forecast the future behavior of the system in the case of accident detection and then compared it with the actual measured data. A cognitive model including qualitative and quantitative information by fuzzy logic of the incident scenario was derived as a fault locator for an ally! chloride plant. The obtained results showed the successful application of cognitive dispersion modeling to process safety analysis. A fuzzy inductive reasoner illustrated good performance to discriminate between different types of malfunctions. This fault locator allowed risk analysis and the construction of a fault tolerant system. This study is the first report in the literature showing the cognitive reliability analysis method.

  10. THE COMPATIBILITY OF BLENDS OF POLY(VINYL CHLORIDE) OR CHLORINATED POLY(VINYL CHLORIDE) WITH POLY(METHYL METHACRYLATE)

    Institute of Scientific and Technical Information of China (English)

    WANG Qingguo; CHENG Rongshi

    1988-01-01

    IR spectral shifts of carbonyl vibrational absorption for ethyl acetate, which acts analogically as the structural unit of poly(methyl methacrylate), in cyclohexane, chloroform, chlorinated paraffins, poly(vinyl chloride) and chlorinated poly(vinyl chloride) were measured. The results suggest that there are specific interactions between the carbonyl groups and the chlorinated hydrocarbons which could be responsible for the apparent compatibility of poly(vinyl chloride) -poly(methyl methacrylate) and chlorinated poly(vinyl chloride) -poly(methyl methacrylate) blends. Additionally, the effects of the preparation mode of blend films on phase separation and observed compatibility are discussed.

  11. Speciation of the bio-available iodine and bromine forms in edible seaweed by high performance liquid chromatography hyphenated with inductively coupled plasma-mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Romaris-Hortas, Vanessa; Bermejo-Barrera, Pilar [Department of Analytical Chemistry, Nutrition and Bromatology, Faculty of Chemistry, University of Santiago de Compostela, Avenida das Ciencias, s/n. 15782 - Santiago de Compostela (Spain); Moreda-Pineiro, Jorge [Department of Analytical Chemistry, Faculty of Sciences, University of A Coruna, Campus da Zapateira, s/n. 15071, A Coruna (Spain); Moreda-Pineiro, Antonio, E-mail: antonio.moreda@usc.es [Department of Analytical Chemistry, Nutrition and Bromatology, Faculty of Chemistry, University of Santiago de Compostela, Avenida das Ciencias, s/n. 15782 - Santiago de Compostela (Spain)

    2012-10-01

    Highlights: Black-Right-Pointing-Pointer Bioavailable iodine and bromine speciation in edible seaweed were developed. Black-Right-Pointing-Pointer In vitro dialyzability was used to assess the bioavailable fractions. Black-Right-Pointing-Pointer AEC hyphenated with inductively coupled plasma-mass spectrometry was used. Black-Right-Pointing-Pointer Iodide, MIT, DIT, bromide and bromate were found in dialyzates from edible seaweed. Black-Right-Pointing-Pointer Positive correlation between bioavailability and protein contents was found. - Abstract: A bioavailability study based on an in vitro dialyzability approach has been applied to assess the bio-available fractions of iodine and bromine species from edible seaweed. Iodide, iodate, 3-iodo-tyrosine (MIT), 3,5-diiodo-tyrosine (DIT), bromide and bromate were separated by anion exchange chromatography under a gradient elution mode (175 mM ammonium nitrate plus 15% (v/v) methanol, pH 3.8, as a mobile phase, and flow rates within the 0.5-1.5 mL min{sup -1} range). Inductively coupled plasma-mass spectrometry (ICP-MS) was used as a selective detector for iodine ({sup 127}I) and bromine ({sup 79}Br). Low dialyzability ratios (within the 2.0-18% range) were found for iodine species; whereas, moderate dialyzability percentages (from 9.0 to 40%) were obtained for bromine species. Iodide and bromide were the major species found in the dialyzates from seaweed, although MIT and bromate were also found in the dialyzates from most of the seaweed samples analysed. However, DIT was only found in dialyzates from Wakame, Kombu, and NIES 09 (Sargasso) certified reference material; whereas, iodate was not found in any dialyzate. Iodine dialyzability was found to be dependent on the protein content (negative correlation), and on the carbohydrate and dietary fibre levels (positive correlation). However, bromine dialyzability was only dependent on the protein amount in seaweed (negative correlation).

  12. Rapid identification of polystyrene foam wastes containing hexabromocyclododecane or its alternative polymeric brominated flame retardant by X-ray fluorescence spectroscopy.

    Science.gov (United States)

    Schlummer, Martin; Vogelsang, Jörg; Fiedler, Dominik; Gruber, Ludwig; Wolz, Gerd

    2015-07-01

    The brominated flame retardant hexabromocyclododecane (HBCDD) was added to Annex A of the list of persistent organic pollutants (POPs) of the Stockholm Convention. Thus, production and use of HBCDD will be banned, and the recycling of HBCDD-containing foam waste will be restricted. In reaction a special polymeric brominated flame retardant (PolyFR) was developed to replace HBCDD in expanded and extruded polystyrene foams for building and construction applications. A decision has to be made at some future time whether expanded and extruded polystyrene foam waste is to be subjected to incineration (with HBCDD) or to recycling (without HBCDD). Therefore, an appropriate and rapid field method is required to distinguish between foams containing HBCDD and foams free from HBCDD. Here we present a screening method for identifying HBCDD containing expanded and extruded polystyrene foams. The test principle is based on the fact that PolyFR (a brominated polymeric macromolecule) is not extractable whereas HBCDD (a low molecular weight substance) is extractable. Following rapid extraction of HBCDD the brominated flame retardant is identified and quantified via bromine analysis using a handheld X-ray fluorescence instrument. The method was applied successfully to 27 expanded and extruded polystyrene foam samples (foams and extruded polystyrene foam raw materials), which were provided without any information about the applied flame retardant. The presence of HBCDD was confirmed for all HBCDD-positive samples in the test. A robustness test revealed a high degree of correctness and a high repeatability for the test system: samples containing HBCDD and HBCDD-free samples were identified correctly with relative standard deviations of quantitative results below 14%. Moreover, X-ray fluorescence spectroscopy test results agree well with HBCDD determinations performed in a laboratory with a gas chromatograph coupled to a flame ionisation detector.

  13. Deriving an atmospheric budget of total organic bromine using airborne in situ measurements from the western Pacific area during SHIVA

    Science.gov (United States)

    Sala, S.; Bönisch, H.; Keber, T.; Oram, D. E.; Mills, G.; Engel, A.

    2014-07-01

    During the recent SHIVA (Stratospheric Ozone: Halogen Impacts in a Varying Atmosphere) project an extensive data set of all halogen species relevant for the atmospheric budget of total organic bromine was collected in the western Pacific region using the Falcon aircraft operated by the German Aerospace agency DLR (Deutsches Zentrum für Luft- und Raumfahrt) covering a vertical range from the planetary boundary layer up to the ceiling altitude of the aircraft of 13 km. In total, more than 700 measurements were performed with the newly developed fully automated in situ instrument GHOST-MS (Gas chromatograph for the Observation of Tracers - coupled with a Mass Spectrometer) by the Goethe University of Frankfurt (GUF) and with the onboard whole-air sampler WASP with subsequent ground-based state-of-the-art GC / MS analysis by the University of East Anglia (UEA). Both instruments yield good agreement for all major (CHBr3 and CH2Br2) and minor (CH2BrCl, CHBrCl2 and CHBr2Cl) VSLS (very short-lived substances), at least at the level of their 2σ measurement uncertainties. In contrast to the suggestion that the western Pacific could be a region of strongly increased atmospheric VSLS abundance (Pyle et al., 2011), we found only in the upper troposphere a slightly enhanced amount of total organic bromine from VSLS relative to the levels reported in Montzka and Reimann et al. (2011) for other tropical regions. From the SHIVA observations in the upper troposphere, a budget for total organic bromine, including four halons (H-1301, H-1211, H-1202, H-2402), CH3Br and the VSLS, is derived for the level of zero radiative heating (LZRH), the input region for the tropical tropopause layer (TTL) and thus also for the stratosphere. With the exception of the two minor VSLS CHBrCl2 and CHBr2Cl, excellent agreement with the values reported in Montzka and Reimann et al. (2011) is found, while being slightly higher than previous studies from our group based on balloon-borne measurements.

  14. Maternal transfer of emerging brominated and chlorinated flame retardants in European eels

    Energy Technology Data Exchange (ETDEWEB)

    Sühring, Roxana, E-mail: roxana.suehring@hzg.de [Helmholtz-Zentrum Geesthacht, Centre for Materials and Coastal Research, Institute of Coastal Research, Department for Environmental Chemistry, Max-Planck-Strasse 1, 21502 Geesthacht (Germany); Leuphana University Lüneburg, Institute of Sustainable and Environmental Chemistry, Scharnhorststraße 1, 21335 Lüneburg (Germany); Freese, Marko [Thünen Institute of Fisheries Ecology, Palmaille 9, 22767 Hamburg (Germany); Schneider, Mandy [Leuphana University Lüneburg, Institute of Sustainable and Environmental Chemistry, Scharnhorststraße 1, 21335 Lüneburg (Germany); Schubert, Sophia; Pohlmann, Jan-Dag [Thünen Institute of Fisheries Ecology, Palmaille 9, 22767 Hamburg (Germany); Alaee, Mehran [Water Science and Technology Directorate, Environment Canada, Burlington, Ontario, L7R4A6 Canada (Canada); Wolschke, Hendrik [Helmholtz-Zentrum Geesthacht, Centre for Materials and Coastal Research, Institute of Coastal Research, Department for Environmental Chemistry, Max-Planck-Strasse 1, 21502 Geesthacht (Germany); Leuphana University Lüneburg, Institute of Sustainable and Environmental Chemistry, Scharnhorststraße 1, 21335 Lüneburg (Germany); Hanel, Reinhold [Thünen Institute of Fisheries Ecology, Palmaille 9, 22767 Hamburg (Germany); Ebinghaus, Ralf [Helmholtz-Zentrum Geesthacht, Centre for Materials and Coastal Research, Institute of Coastal Research, Department for Environmental Chemistry, Max-Planck-Strasse 1, 21502 Geesthacht (Germany); Marohn, Lasse [Thünen Institute of Fisheries Ecology, Palmaille 9, 22767 Hamburg (Germany)

    2015-10-15

    The European eel (Anguilla anguilla) is regarded as a critically endangered species. Scientists are in agreement that the “quality of spawners” is a vital factor for the survival of the species. This quality can be impaired by parasites, disease and pollution. Especially endocrine disrupting organic chemicals pose a potential threat to reproduction and development of offspring. To our knowledge, the findings in this publication for the first time describe maternal transfer of contaminants in eels. We analysed the concentrations of in total 53 polybrominated diphenyl ethers (PBDEs) and their halogenated substitutes in muscle, gonads and eggs of artificially matured European eels and in muscle and gonads of untreated European eels that were used for comparison. We found evidence that persistent organic pollutants such as PBDEs, as well as their brominated and chlorinated substitutes are redistributed from muscle tissue to gonads and eggs. Concentrations ranged from 0.001 ng g{sup −1} ww for sum Dechlorane metabolites (DPMA, aCL{sub 10}DP, aCl{sub 11}DP) to 2.1 ng g{sup −1} ww for TBA in eggs, 0.001 ng g{sup −1} ww for Dechlorane metabolites to 9.4 ng g{sup −1} ww for TBA in gonads and 0.002 ng g{sup −1} ww for Dechlorane metabolites to 54 ng g{sup −1} ww for TBA in muscle tissue. Average egg muscle ratios (EMRs) for compounds detectable in artificially matured eels from both Schlei Fjord and Ems River ranged from 0.01 for Dechlorane 602 (DDC-DBF) to 10.4 for PBEB. Strong correlations were found between flame retardant concentrations and lipid content in the analysed tissue types, as well as transfer rates and octanol–water partitioning coefficient, indicating that these parameters were the driving factors for the observed maternal transfer. Furthermore, indications were found, that TBP-DBPE, TBP-AE, BATE and TBA have a significant uptake from the surrounding water, rather than just food and might additionally be formed by metabolism or

  15. 21 CFR 177.1980 - Vinyl chloride-propylene copolymers.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use as... applicable to vinyl chloride-propylene copolymers used in food-packaging adhesives complying with § 175.105... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Vinyl chloride-propylene copolymers....

  16. 46 CFR 154.1745 - Vinyl chloride: Transferring operations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride: Transferring operations. 154.1745 Section 154.1745 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS... Operating Requirements § 154.1745 Vinyl chloride: Transferring operations. A vessel carrying vinyl...

  17. Phosphatase inhibitors activate normal and defective CFTR chloride channels

    OpenAIRE

    Becq, F; Jensen, T J; Chang, X B; Savoia, A.; Rommens, J M; Tsui, L C; Buchwald, M; Riordan, J R; Hanrahan, J W

    1994-01-01

    The cystic fibrosis transmembrane conductance regulator (CFTR) chloride channel is regulated by phosphorylation and dephosphorylation at multiple sites. Although activation by protein kinases has been studied in some detail, the dephosphorylation step has received little attention. This report examines the mechanisms responsible for the dephosphorylation and spontaneous deactivation ("rundown") of CFTR chloride channels excised from transfected Chinese hamster ovary (CHO) and human airway epi...

  18. Experimental and numerical investigation of chloride ingress in cracked concrete

    NARCIS (Netherlands)

    Šavija, B.

    2014-01-01

    Chloride induced corrosion of reinforcing steel is recognized as the most common deterioration mechanism affecting reinforced concrete structures. As such, it has been in focus of research for more than thirty years. Numerous studies of chloride ingress, corrosion initiation, and corrosion propagati

  19. Microwave Mapping Demonstration Using the Thermochromic Cobalt Chloride Equilibrium

    Science.gov (United States)

    Nguyen, Vu D.; Birdwhistell, Kurt R.

    2014-01-01

    An update to the thermochromic cobalt(II) chloride equilibrium demonstration is described. Filter paper that has been saturated with aqueous cobalt(II) chloride is heated for seconds in a microwave oven, producing a color change. The resulting pink and blue map is used to colorfully demonstrate Le Châtelier's principle and to illuminate the…

  20. Hydrophobic treatment of concrete as protection against chloride penetration

    NARCIS (Netherlands)

    Vries, J. de; Polder, R.B.; Borsje, H.

    1996-01-01

    Hydrophobic treatment makes a concrete surface absorb less water and less chloride. Hydrophobic treatment was studied as a protection agninst chloride penetration from deicing salts. Test methods were designed. Nine hydrophobic products were tested, of which three complied to the requirements on fin

  1. Chloride penetration into cementitious mortar at early age

    NARCIS (Netherlands)

    Caballero, J.; Polder, R.B.; Leegwater, G.A.; Fraaij, A.L.A.

    2012-01-01

    Modern service life design methods for concrete structures use chloride diffusion data as an input parameter. Abundant data exist for concrete at 28 days and, to a lesser extent, at later ages. This paper presents chloride diffusion data for mortar at ages between 1 day and 28 days age. Rapid Chlori

  2. Atmospheric bromine flux from the coastal Abu Dhabi sabkhat: A ground-water mass-balance investigation

    Science.gov (United States)

    Wood, Warren W.; Sanford, Ward E.

    2007-07-01

    A solute mass-balance study of ground water of the 3000 km2 coastal sabkhat (salt flats) of the Emirate of Abu Dhabi, United Arab Emirates, documents an annual bromide loss of approximately 255 metric tons (0.0032 Gmoles), or 85 kg/km2. This value is an order of magnitude greater than previously published direct measurements from the atmosphere over an evaporative environment of a salar in Bolivia. Laboratory evidence, consistent with published reports, suggests that this loss is by vapor transport to the atmosphere. If this bromine flux to the atmosphere is representative of the total earth area of active salt flats then it is a significant, and generally under recognized, input to the global atmospheric bromide flux.

  3. Corrosion mechanism of 13Cr stainless steel in completion fluid of high temperature and high concentration bromine salt

    Science.gov (United States)

    Liu, Yan; Xu, Lining; Lu, Minxu; Meng, Yao; Zhu, Jinyang; Zhang, Lei

    2014-09-01

    A series of corrosion tests of 13Cr stainless steel were conducted in a simulated completion fluid environment of high temperature and high concentration bromine salt. Corrosion behavior of specimens and the component of corrosion products were investigated by means of scanning electron microscope (SEM), confocal laser scanning microscopy (CLSM) and X-ray photoelectron spectroscopy (XPS). The results indicate that 13Cr steel suffers from severe local corrosion and there is always a passive halo around every pit. The formation mechanism of the passive halo is established. OH- ligand generates and adsorbs in a certain scale because of abundant OH- on the surface around the pits. Passive film forms around each pit, which leads to the occurrence of passivation in a certain region. Finally, the dissimilarities in properties and morphologies of regions, namely the pit and its corresponding passive halo, can result in different corrosion sensitivities and may promote the formation of macroscopic galvanic pairs

  4. Unsteady growth of ammonium chloride dendrites

    Science.gov (United States)

    Martyushev, L. M.; Terentiev, P. S.; Soboleva, A. S.

    2016-02-01

    Growth of ammonium chloride dendrites from aqueous solution is experimentally investigated. The growth rate υ and the radius ρ of curvature of branches are measured as a function of the relative supersaturation Δ for steady and unsteady growth conditions. It is shown that the experimental results are quantitatively described by the dependences ρ=a/Δ+b, υ=cΔ2, where the factors for primary branches are a=(1.3±0.2)·10-7 m, b=(2.5±0.4)·10-7 m, and c=(2.2±0.3)·10-4 m/s. The factor c is found to be approximately 7 times smaller for the side branches than that for the primary branches.

  5. Electrochemical properties of actinides in molten chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Lambertin, D.; Lacquement, J. [CEA/VALRHO - site de Marcoule, Dept. de Recherche en Retraitement et en Vitrification, DRRV, 30 - Marcoule (France); Sanchez, S.; Picard, G. [Ecole Nationale Superieure de Chimie de Paris, Lab. d' Electrochimie et de Chimie Analytique, UMR 7575 du CNRS, 75 - Paris (France)

    2000-07-01

    The chemical properties of plutonium and cerium chlorides have been studied in the fused CaCl{sub 2}-NaCl equimolar mixture at 550 deg. C using a tungsten working electrode and a pO{sup 2-} indicator electrode. The standard potential of Pu(III)/Pu was determined using cyclic voltammetry. The solubility product of Pu{sub 2}O{sub 3} was calculated by potentiometric titration. The standard potential of Ce(III)/Ce have been determined by a potentiometry method. Potentiometric titrations of Ce(III) have been shown the existence of a soluble cerium oxychloride. All these data allowed us to draw the potential-pO{sup 2-} diagram which summarises the properties of plutonium and cerium compounds in the melt. (authors)

  6. [Survey of plasticizers in polyvinyl chloride toys].

    Science.gov (United States)

    Abe, Yutaka; Yamaguchi, Miku; Mutsuga, Motoh; Hirahara, Yoshichika; Kawamura, Yoko

    2012-01-01

    Plasticizers in 101 samples of polyvinyl chloride (PVC) toys on the Japanese market were surveyed. No phthalates were detected in designated toys, though bis(2-ethylhexyl)phthalate, diisononyl phthalate, diisobutyl phthalate, dibutyl phthalate, diisodecyl phthalate and benzyl butyl phthalate were detected in more than half of other toys. 2,2,4-Tributyl-1,3-pentanediol diisobutylate, o-acetyl tributyl citrate, adipates and diacetyl lauroyl glycerol, which are alternative plasticizers to phthalates, were detected. The results of structural analysis confirmed the presence of di(2-ethylhexyl)terephthalate, tributyl citrate, diisononyl 1,2-cyclohexanedicarboxylate and neopentyl glycol esters; these have not previonsly been reported in Japan. There appears to be a shift in plasticizers used for designated toys from phthalates to new plasticizers, and the number of different plasticizers is increasing.

  7. Estimating the chloride transport in cement paste

    Directory of Open Access Journals (Sweden)

    Princigallo, A.

    2012-06-01

    Full Text Available A method was developed to measure the diffusion coefficient of chloride ions in cement paste based on an analytical solution to Fick’s 2nd law in a cylindrical coordinate system. This natural method yielded diffusivity results within as little as a month. Testing time was reduced by exploiting the three-dimensional inward flux in the specimen. In an attempt to determine the saturation concentration, dense portland cement pastes were exposed to a concentrated chloride solution. The method proved to be useful for exploring cement hydration-induced changes in the diffusion coefficient of cement paste.

    Se ha desarrollado un método para medir el coeficiente de difusión de los iones cloruro en la pasta de cemento, partiendo de una aplicación analítica de la segunda ley de Fick en un sistema de coordinadas cilíndrico. Este método, que es natural, demostró ser capaz de producir resultados de difusividad en tan solo un mes. Se consiguió reducir el tiempo de ensayo mediante el aprovechamiento de la tridimensionalidad del flujo desde el exterior al interior de la probeta. A fin de determinar la concentración de saturación, se sometieron las pastas de cemento Portland a una disolución de cloruros concentrada. Este método resultó ser útil en el estudio de los cambios del coeficiente de difusión de la pasta de cemento provocados por las reacciones de hidratación que tienen lugar en esta.

  8. Exposure to Brominated Trihalomethanes in Water During Pregnancy and Micronuclei Frequency in Maternal and Cord Blood Lymphocytes

    Science.gov (United States)

    Pedersen, Marie; Patelarou, Evridiki; Decordier, Ilse; Vande Loock, Kim; Chatzi, Leda; Espinosa, Ana; Fthenou, Eleni; Nieuwenhuijsen, Mark J.; Gracia-Lavedan, Esther; Stephanou, Euripides G.; Kirsch-Volders, Micheline; Kogevinas, Manolis

    2013-01-01

    Background: Water disinfection by-products have been associated with an increased cancer risk. Micronuclei (MN) frequency in lymphocytes is a marker of genomic damage and can predict adult cancer risk. Objective: We evaluated maternal exposure to drinking water brominated trihalomethanes (BTHM) in relation to MN frequency in maternal and cord blood lymphocytes. Methods: MN frequency was examined in 214 mothers and 223 newborns from the Rhea mother–child cohort in Crete, Greece, in 2007–2008. Residential BTHM water concentrations were estimated during pregnancy using tap water analyses and modeling. Questionnaires on water related habits were used to estimate BTHM exposure from all routes. Associations between BTHM and MN frequency were estimated using negative binomial regression. Results: BTHM concentrations in residential tap water during pregnancy ranged from 0.06 to 7.1 μg/L. MN frequency in maternal binucleated lymphocytes was found to increase with BTHM concentrations in residential water for exposure during the first [rate ratio (RR) for 1 μg/L = 1.05; 95% CI: 1.00, 1.11] and second trimesters (RR for 1 μg/L = 1.03; 95% CI: 1.00, 1.06), and through all routes of BTHM exposure during the first trimester (RR for 1 μg/week = 3.14; 95% CI: 1.16, 8.50). Conclusions: These findings suggest that exposure to BTHM may increase the frequency of MN in maternal binucleated lymphocytes. Citation: Stayner LT, Pedersen M, Patelarou E, Decordier I, Vande Loock K, Chatzi L, Espinosa A, Fthenou E, Nieuwenhuijsen MJ, Gracia-Lavedan E, Stephanou EG, Kirsch-Volders M, Kogevinas M. 2014. Exposure to brominated trihalomethanes in water during pregnancy and micronuclei frequency in maternal and cord blood lymphocytes. Environ Health Perspect 122:100–106; http://dx.doi.org/10.1289/ehp.1206434 PMID:24184846

  9. Polybrominated diphenyl ethers (PBDEs) and alternative brominated flame retardants in air and seawater of the European Arctic

    Energy Technology Data Exchange (ETDEWEB)

    Moeller, Axel, E-mail: axel.moeller@hzg.de [Helmholtz-Zentrum Geesthacht, Centre for Materials and Coastal Research, Institute of Coastal Research, Department for Environmental Chemistry, Max-Planck-Strasse 1, 21502 Geesthacht (Germany); Xie Zhiyong; Sturm, Renate; Ebinghaus, Ralf [Helmholtz-Zentrum Geesthacht, Centre for Materials and Coastal Research, Institute of Coastal Research, Department for Environmental Chemistry, Max-Planck-Strasse 1, 21502 Geesthacht (Germany)

    2011-06-15

    The spatial distribution of polybrominated diphenyl ethers (PBDEs) and several alternative non-PBDE, non-regulated brominated flame retardants (BFRs) in air and seawater and the air-seawater exchange was investigated in East Greenland Sea using high-volume air and water samples. Total PBDE concentrations (O{sub 10}PBDEs) ranged from 0.09 to 1.8 pg m{sup -3} in the atmosphere and from 0.03 to 0.64 pg L{sup -1} in seawater. Two alternative BFRs, Hexabromobenzene (HBB) and 2,3-dibromopropyl-2,4,6-tribromophenyl ether (DPTE), showed similar concentrations and spatial trends as PBDEs. The air-seawater gas exchange was dominated by deposition with fluxes up to -492 and -1044 pg m{sup -2} day{sup -1} for BDE-47 and DPTE, respectively. This study shows the first occurrence of HBB, DPTE and other alternative flame retardants (e.g., pentabromotoluene (PBT)) in the Arctic atmosphere and seawater indicating that they have a similar long-range atmospheric transport potential (LRAT) as the banned PBDEs. - Highlights: > Flame retardants undergo long-range atmospheric transport to East Greenland Sea. > Western Europe is a source of flame retardants in the European Arctic. > Alternative flame retardants HBB and DPTE show concentrations similar to PBDEs. > Air-sea exchange of brominated flame retardants is dominated by net deposition. - Alternative flame retardants hexabromobenzene (HBB) and 2,3-dibromopropyl-2,4,6-tribromophenyl ether (DPTE) undergo long-range atmospheric transport to the Arctic.

  10. Levels of brominated flame retardants and other pesistent organic pollutants in breast milk samples from Limpopo province, South Africa

    Energy Technology Data Exchange (ETDEWEB)

    Darnerud, Per Ola, E-mail: poda@slv.se [Toxicology Division, National Food Administration, P.O. Box 622, SE-751 26 Uppsala (Sweden); Aune, Marie; Larsson, Lotta [Chemistry Division 2, National Food Administration, P.O. Box 622, SE-751 26 Uppsala (Sweden); Lignell, Sanna [Toxicology Division, National Food Administration, P.O. Box 622, SE-751 26 Uppsala (Sweden); Mutshatshi, Tshinanne; Okonkwo, Jonathan; Botha, Ben [Faculty of Science, Tshwane University of Technology, Pretoria (South Africa); Agyei, Nana [Department of Chemistry, Limpopo University, Medunsa (South Africa)

    2011-09-01

    The non-occupational exposure to brominated flame retardants, and other persistent organic pollutants (POPs) was studied by collecting human breast milk samples from mothers residing in Thohoyandou area, a rural district in the Limpopo Province, northern part of South Africa (SA). Of all collected samples to be analysed (n = 28), those with large enough milk volumes, (n = 14) were quantified for polybrominated diphenyl ethers (PBDEs) (9 congeners: BDE-28, 47, 66, 99, 100, 138, 153, 154, and 183) and hexabromocyclododecane (HBCD) on a GC equipped with dual capillary columns and dual electron-capture detectors (ECD). The levels of PBDE congeners (median sumBDE 1.3 ng/g of lipids) and of HBCD were not far from levels generally found in European studies, and this study may be the first report on the presence of PBDEs and HBCD in SA breast milk. On a congener basis, the finding of comparably high BDE-183 levels suggests a specific PBDE usage, or contamination situation in SA. Apart from BFRs, the high DDT levels found in the breast milk from this area (median and maximum sumDDT levels of about 4 600 and over 20 000 ng/g of lipids, respectively; n = 28) have earlier been reported. In addition, other POPs (PCBs, HCB and HCHs) were found in SA breast milk, at relatively low levels. To conclude, measurable levels of PBDEs and HBCD, and a specific BDE congener pattern, were found in breast milk from the Limpopo province, SA. A number of other POPs, including DDTs in high levels, were also present. - Highlights: {yields} Persistent organic pollutants (POPs) were analysed in South African breast milk. {yields} Focus of interest were brominated flame retardants (BRFs). {yields} Sampling area was the rural Limpopo Province, northern SA. {yields} Probably the first reported African data on BFRs (PBDEs, HBCD) in breast milk. {yields} Reported BFR data similar to European levels.

  11. Behavior and products of mechano-chemical dechlorination of polyvinyl chloride and poly (vinylidene chloride).

    Science.gov (United States)

    Xiao, Xiao; Zeng, Zigao; Xiao, Songwen

    2008-02-28

    The mechano-chemical (MC) dechlorination of polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) was performed by mechanical milling PVC/PVDC powder with zinc powder in a planetary ball mill, and the products of dechlorination were characterized by Infrared spectra (IR), X-ray diffraction (XRD), Raman spectroscopy, gas chromatography-mass spectrometry (GC-MS), and 13C solid-state nuclear magnetic resonance (NMR). The experimental results show that PVC/PVDC can be easily dechlorinated by milling with zinc powder, and formed various kinds of inorganic and organic products. Inorganic compounds included Zn2OCl(2).2H2O, Zn5(OH)8Cl2.H2O etc., and organic products involved diamond-like carbon, carbyne fragment, polyacetylene etc. Organic products formed following the paths of dechlorination, dehydrochlorination, crosslink, and oxidation. The mechano-chemical dechlorination process of PVC/PVDC may be an effective approach for carbyne synthesizing in the appropriate condition.

  12. Effects of cyclic chloride exposure on penetration of concrete cover

    Energy Technology Data Exchange (ETDEWEB)

    Hong, K.; Hooton, R.D.

    1999-09-01

    Concretes are in a state of flux between saturated and partially saturated conditions as they undergo continuous cycles of wetting and drying. In saturated concrete, dissolved ions enter through diffusion, whereas in partially saturated concrete, ion-containing fluids are absorbed by capillary suction and concentrated by evaporation of water. The primary focus of this study was to examine the effects of cyclic wetting and drying with sodium chloride solution on chloride ingress into concrete. Chloride profiles of samples exposed to various lengths and numbers of cycles were determined for three mixtures of concrete: two containing slag and/or silica fume with a 0.4 w/cm (water to cementing materials ratio) and one with a 0.3 w/cm. It was found that longer drying times increase the rate of chloride ingress. A good relationship exists between the depth of chloride penetration and the square root of the number of cycles.

  13. Determination of the heat capacities of Lithium/BCX (bromide chloride in thionyl chloride) batteries

    Science.gov (United States)

    Kubow, Stephen A.; Takeuchi, Kenneth J.; Takeuchi, Esther S.

    1989-12-01

    Heat capacities of twelve different Lithium/BCX (BrCl in thionyl chloride) batteries in sizes AA, C, D, and DD were determined. Procedures and measurement results are reported. The procedure allowed simple, reproducible, and precise determinations of heat capacities of industrially important Lithium/BCX cells, without interfering with performance of the cells. Use of aluminum standards allowed the accuracy of the measurements to be maintained. The measured heat capacities were within 5 percent of calculated heat capacity values.

  14. PHASE EQUILIBRIUM FOR THE TERNARY SYSTEM VINYL CHLORIDE-CHLORINATED POLYETHYLENE-POLY (VINYL CHLORIDE)

    Institute of Scientific and Technical Information of China (English)

    LOU Jianfeng; WENG Zhixue; HUANG Zhiming; PAN Zuren

    1991-01-01

    Swelling capacity of vinyl chloride (VC) in chlorinated polyethylene (CPE) with 25- 40 wt% Cl at temperature 30- 57 ℃ was studied and their relationships were correlated with Langmuir and Freundlich adsorption equations. A ternary phase diagram for VC-CPE-PVC was also established.In-situ polymerization conditions of CPE-g -VC were proposed and CPE content control was analyzed for the manufacturing process of CPE-g-VC graft product based on results of phase equilibrium study.

  15. Genetically encoded optical sensors for monitoring of intracellular chloride and chloride-selective channel activity

    Directory of Open Access Journals (Sweden)

    Piotr Bregestovski

    2009-12-01

    Full Text Available This review briefly discusses the main approaches for monitoring chloride (Cl−, the most abundant physiological anion. Noninvasive monitoring of intracellular Cl− ([Cl−]i is a challenging task owing to two main difficulties: (i the low transmembrane ratio for Cl−, approximately 10:1; and (ii the small driving force for Cl−, as the Cl− reversal potential (ECl is usually close to the resting potential of the cells. Thus, for reliable monitoring of intracellular Cl−, one has to use highly sensitive probes. From several methods for intracellular Cl− analysis, genetically encoded chloride indicators represent the most promising tools. Recent achievements in the development of genetically encoded chloride probes are based on the fact that yellow fluorescent protein (YFP exhibits Cl−-sensitivity. YFP-based probes have been successfully used for quantitative analysis of Cl− transport in different cells and for high-throughput screening of modulators of Cl−-selective channels. Development of a ratiometric genetically encoded probe, Clomeleon, has provided a tool for noninvasive estimation of intracellular Cl− concentrations. While the sensitivity of this protein to Cl− is low (EC50 about 160 mM, it has been successfully used for monitoring intracellular Cl− in different cell types. Recently a CFP–YFP-based probe with a relatively high sensitivity to Cl− (EC50 about 30 mM has been developed. This construct, termed Cl-Sensor, allows ratiometric monitoring using the fluorescence excitation ratio. Of particular interest are genetically encoded probes for monitoring of ion channel distribution and activity. A new molecular probe has been constructed by introducing into the cytoplasmic domain of the Cl−-selective glycine receptor (GlyR channel the CFP–YFP-based Cl-Sensor. This construct, termed BioSensor-GlyR, has been successfully expressed in cell lines. The new genetically encoded chloride probes offer means of screening

  16. Optical, thermal and magnetic studies of pure and cobalt chloride doped L-alanine cadmium chloride

    Science.gov (United States)

    Benila, B. S.; Bright, K. C.; Delphine, S. Mary; Shabu, R.

    2017-03-01

    Single crystals of L-alanine cadmium chloride (LACC) and cobalt chloride (Co2+) doped LACC have been grown by the slow evaporation solution growth technique. The grown crystals were subjected to various characterizations such as powder XRD, SXRD, FTIR, UV-vis, EDAX, TG/DTA, VSM, Dielectric and Second Harmonic Generation (SHG) measurements. The lattice parameters of the grown crystals were determined by single crystal X-ray analysis. EDAX analysis confirms the presence of Co2+ ion in the host material. The functional group and optical behavior of the crystals were identified from FTIR and UV-vis spectrum analysis. Electrical parameters such as dielectric constant, dielectric loss have been studied. The thermal stability of the compound was found out using TGA/DTA analysis. Second Harmonic Generation of the samples was confirmed by Kurtz-Perry powder technique. Magnetic properties of the crystals studied by VSM were also reported. The encouraging results show that the cobalt chloride doped LACC crystals have greater potential applications in optical devices.

  17. Comparative effects of hydrogen chloride gas on tomato and chrysanthemum. I. Distribution and accumulation of chloride following exposure. II. Pathological anatomy of hydrogen chloride gas injury

    Energy Technology Data Exchange (ETDEWEB)

    Shriner, D.S.

    1969-01-01

    Hydrogen chloride (HCl) gas damage to plants has not been a historically important problem. However, recent practices in a number of industries, particularly glass manufacturing and pyrolysis of waste plastics, have increased the seriousness of the problem. Studies were carried out under carefully controlled exposure conditions to determine the effects of HCl gas on a relatively sensitive and a relatively resistant plant species. The macroscopic symptoms of most importance in acute damage to tomato and chrysanthemum are glazing of the lower surface, and a bifacial bronzing of interveinal and marginal areas of leaves. Microscopically, glazing was shown to be caused by a collapse of the lower epidermal cells and a partial disorganization of the spongy mesophyll of leaves. Bronzing was shown to be caused by the further collapse of the spongy mesophyll, and in some cases the palisade mesophyll and upper epidermis. Analysis of plant tissues for their free chloride content following an exposure to HCl gas was done with cell-free water extracts which were titrated on an automatic chloride titrator. On the basis of such studies, evidence suggest that the mechanism of accumulation of chlorides in plants is similar to that of fluorides, and that in subacute doses, chlorides are translocated toward the extremities of the foliar portions of the plant. In areas where a number of different types of pollution sources exist, and symptomotology is not definitive in pinpointing the source, chloride analysis of plant tissues should prove valuable as an aid to diagnosis if HCl gas was suspected.

  18. Acute lethal and teratogenic effects of tributyltin chloride and copper chloride on mahi mahi (Coryphaena hippurus) eggs and larvae.

    Science.gov (United States)

    Adema-Hannes, Rachel; Shenker, Jonathan

    2008-10-01

    Acute and chronic bioassays were used to evaluate the lethal and sublethal effects of copper chloride and tributyltin chloride on mahi mahi (Coryphaena hippurus) embryos, a pelagic life stage often found in the surface microlayer where anthropogenic contaminants can accumulate. Acute bioassay testing determined the median lethal concentration (LC50) for the test organism after 48 h of exposure. Chronic toxicity tests were used to determine the measurement of sublethal parameters, such as developmental abnormalities after 72-h exposures to the toxicants. Embryos were collected 4 h postfertilization and subsequently exposed to 1, 5, 25, 50, and 100 microg/L of copper chloride and 3, 10, 20, 30, and 50 microg/L of tributyltin chloride. Analysis of hatch rate percentage determined that the mean 48-h LC50 of copper chloride and tributyltin chloride was 32.8 and 16.7 microg/L, respectively, based on the pooled data of four experiments with four replicates for each metal. Consistent abnormalities, such as yolk sac swelling, spinal deformities, and decreased hatch rates, were observed for each metal. Teratogenic responses to copper chloride and tributyltin chloride demonstrate the need to investigate further the impacts of pollution in the open oceans to a species indigenous to, and commercially important to, the Florida (USA) coasts. This information could then lead to the future development of a surface microlayer bioassay using mahi mahi embryos.

  19. Chloride penetration into concrete under simulated field conditions

    Energy Technology Data Exchange (ETDEWEB)

    Motohashi, K.; Misra, S.; Yamamoto, A. (Kajima Corp., Tokyo (Japan))

    1991-10-31

    The purpose of this study is to clarify the effect of field conditions such curing period, slump, maximum size of aggregate, etc. on chloride penetration into concrete. With a view to closely simulate the field conditions, all specimens were exposed to chloride attack for five days after casting. From the preliminary results obtained after a six month immersion in 3.3% NaCl solution, higher degrees of chloride ingress were observed in cases when the concrete was prematurely exposed to chloride attack or had a higher slump. In addition, apart from properties, such as water-cement ratio, etc., the relative orientation of the direction of penetration to that of casting, the mortar content of the mix, and the properties of the transition zone between the coarse aggregate and mortar were found to affect the diffusivity of the chloride. Under a limited number of conditions, soluble chloride content was also illustrated in addition to the total chlorides. 10 refs., 6 figs., 6 tabs.

  20. Modeling and experimental studies to optimize the performance of a hydrogen - bromine fuel cell

    Science.gov (United States)

    Yarlagadda, Venkata Raviteja

    The regenerative Hydrogen-Bromine (H2-Br 2) fuel cells are considered to be one of the viable systems for large scale energy storage because of their high energy conversion efficiency, flexible operation, highly reversible reactions and low capital cost. The preliminary performance of a H2-Br2 fuel cell using both conventional as well as novel materials (Nafion and electrospun composite membranes along with platinum and rhodium sulfide electrocatalysts) was discussed. A maximum power density of 0.65 W/cm2 was obtained with a thicker Br 2 electrode (780 mum) and cell temperature of 45°C. The active area and wetting characteristics of Br2 electrodes were improved upon by either pre-treating with HBr or boiling them in de-ionized water. On the other hand, similar or better performances were obtained using dual fiber electrospun composite membranes (maximum power densities of 0.61 W/cm2 and 0.45 W/cm2 obtained with 25 mum and 65 mum electrospun membranes at 45°C) versus using Nafion membranes (maximum power densities of 0.52 W/cm 2 and 0.41 W/cm2 obtained with Nafion 212 and Nafion 115 membranes at 45°C). The rhodium sulfide (RhxSy) electrocatalyst proved to be more stable in the presence of HBr/Br2 than pure Pt. However, the H2 oxidation activity on RhxS y was quite low compared to that of Pt. In conclusion, a stable H 2 electrocatalyst that can match the hydrogen oxidation activity obtained with Pt and a membrane with low Br2/Br- permeability are essential to prolong the lifetime of a H2-Br2 fuel cell. A 1D mathematical model was developed to serve as a theoretical guiding tool for the experimental studies. The impact of convective and diffusive transport and kinetic rate on the performance of a H2-Br2 fuel cell is shown in this study. Of the two flow designs (flow-by and flow-through) incorporated in this study, the flow-through design demonstrated better performance, which can be attributed to the dominant convective transport inside the porous electrode. Both

  1. Acetogenic microbial degradation of vinyl chloride

    Science.gov (United States)

    Bradley, P.M.; Chapelle, F.H.

    2000-01-01

    Under methanogenic conditions, microbial degradation of [1,2-14C]vinyl chloride (VC) resulted in significant (14 ?? 3% maximum recovery) but transient recovery of radioactivity as 14C-acetate. Subsequently, 14C- acetate was degraded to 14CH4 and 14CO2 (18 ?? 2% and 54 ?? 3% final recoveries, respectively). In contrast, under 2-bromoethanesulfonic acid (BES) amended conditions, 14C-acetate recovery remained high (27 ?? 1% maximum recovery) throughout the study, no 14CH4 was produced, and the final recovery of 14CO2 was only 35 ?? 4%. These results demonstrate that oxidative acetogenesis may be an important mechanism for anaerobic VC biodegradation. Moreover, these results (1) demonstrate that microbial degradation of VC to CH4 and CO2 may involve oxidative acetogenesis followed by acetotrophic methanogenesis and (2) suggest that oxidative acetogenesis may be the initial step in the net oxidation of VC to CO2 reported previously under Fe(III)-reducing, SO4-reducing, and humic acids- reducing conditions.Under methanogenic conditions, microbial degradation of [1,2-14C]vinyl chloride (VC) resulted in significant (14 ?? 3% maximum recovery) but transient recovery of radioactivity as 14C-acetate. Subsequently, 14C-acetate was degraded to 14CH4 and 14CO2 (18 ?? 2% and 54 ?? 3% final recoveries respectively). In contrast, under 2-bromoethanesulfonic acid (BES) amended conditions, 14C-acetate recovery remained high (27 ?? 1% maximum recovery) throughout the study, no 14CH4 was produced, and the final recovery of 14CO2 was only 35 ?? 4%. These results demonstrate that oxidative acetogenesis may be an important mechanism for anaerobic VC biodegradation. Moreover, these results (1) demonstrate that microbial degradation of VC to CH4 and CO2 may involve oxidative acetogenesis followed by acetotrophic methanogenesis and (2) suggest that oxidative acetogenesis may be the initial step in the net oxidation of VC to CO2 reported previously under Fe(III)-reducing, SO4-reducing, and

  2. Studies on Hypokalemia Induced by Trimethyltin Chloride

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    To determine the possible relationship between plasma potassium concentration and severity of acute trimethyltin chloride (TMT) poisoning and to assess the mechanism of TMT induced hypokalemia. Methods SD rats were treated with various dosages of TMT (ip). All the indices were measured and analysed for determing their possible relations with plasma K+. Results With increase of dosage, the plasma K+ level dropped rapidly, and deaths appeared more quickly. The LDs0 of TMT (ip) was 14.7 mg/kgbw. In the low dosage group (10 mg/kgbw), the plasma K+ level dropped slowly with the lowest dosage on day 6 (4.85 mmol/L). It rose again on day 11 (5.06 mmol/L), and recoverd on day 28. The poisoning signs corresponded with decline of the span of K+ level. The plasma Na+ level dropped half an hour after TMT treatment, but recovered 24 h later. In the high dosage group (46.4 mg/kgbw), the levels of plasma K+ and Na+ fell rapidly within half an hour (P<0.05), the intracellular potassium concentration of RBC did not decrerase obviously (P>0.05), the activities of Na+-K+-ATPase and Mg2+-ATPase in RBC membrane were depressed remarkably (P<0.01, P<0.05, respectively), the plasma aldosterone concentrations rose as high as tenfold (P<0.01), the arterial blood pH fell from 7.434 to 7.258 (P<0.01),pCO2 was raised from 29.62 to 45.33 mmHg (P<0.01). In the 24 h urine test, when rats were treated with TMT (21.5 mg/kgbw, ip), urine volume, urinary potassium, sodium and chloride increased significantly in comparison with those in the controls (P<0.01). Conclusion TMT could induce hypokalemia in SD rats. The available evidence suggests that TMT can induce acute renal leakage of potassium. At the same time, a significant rise of plasma aldosterone may play an important role in promoting potassium leakage from kidney to result in severe hypokalemia with inhaling acid-base abnormalities produced, which aggravate the poisoning symptoms. In the end the rats would die of respiratory

  3. Molten Triazolium Chloride Systems as New Aluminum Battery Electrolytes

    DEFF Research Database (Denmark)

    Vestergaard, B.; Bjerrum, Niels; Petrushina, Irina;

    1993-01-01

    The possibility of using molten mixtures of 1,4-dimethyl-1,2,4-triazolium chloride (DMTC) and aluminum chloride (AlCl3) as secondary battery electrolytes was studied, in some cases extended by the copresence of sodium chloride. DMTC-AlCl, mixtures demonstrated high specific conductivity in a wide...... of milliamperes per square centimeter) was observed at 0.344 V on the acidic sodium tetrachloroaluminate background, involving a free triazolium radical mechanism. Molten DMTC-AlCl3 electrolytes are acceptable for battery performance and both the aluminum anode and the triazolium electrolyte can be used as active...

  4. Calcium chloride in stabilised soil roads and runways

    Directory of Open Access Journals (Sweden)

    Harsh Vardhan

    1952-09-01

    Full Text Available Mudless, dustless, hard and all weather driving surfaces is a serious requirement of the forces.  surfacing by mixtures of definite amounts of locally available stone, gravel, sand, clay and Silt to which calculated amount of calcium chloride is added quickly compact and ultimately harden like concrete. This provides an easy, quick and economic- means of meeting the requirement.  Necessity of such surfaces, use and action of calcium chloride and resulting effects are discussed. Different methods of construction and application of calcium chloride are briefly related.

  5. Microwave evaluation of accelerated chloride ingress in mortar

    Science.gov (United States)

    Hu, C.; Case, T.; Castle, M.; Zoughi, R.; Kurtis, K.

    2001-04-01

    Corrosion of steel in reinforced concrete structures can be induced by the presence of chloride ions near the steel/concrete interface. To show the potential of microwave nondestructive testing techniques for evaluating chloride ingress, 8″×8″×8″ mortar specimens with different mixture designs were prepared. To accelerate chloride ingress, they were exposed to cyclical wet/dry conditions, where the wet condition included exposure to salt bath. A complete discussion of the results will be presented in this paper.

  6. Denitrification of fertilizer wastewater at high chloride concentration

    DEFF Research Database (Denmark)

    Ucisik, Ahmed Süheyl; Henze, Mogens

    Wastewater from fertilizer industry is characterized by high contents of chloride concentration, which normally vary between 60 and 76 g/l. Experiments with bilogical denitrification were performed in lab-scale "fill and draw" reactors with synthetic wastewater with chloride concentrations up to 77.......4 g/l. The results of the experiments showed that biological denitrification was feasible at the extreme environmental conditions prevailing in fertilizer wastewater. Stable continuous biological denitrfication of the synthetic high chloride wastewater was performed up to 77.4 g Cl/l at 37 degree C...

  7. The ionic product of water in concentrated tetramethylammonium chloride solutions.

    Science.gov (United States)

    Sipos, P; Bódi, I; May, P M; Hefter, G T

    1997-04-01

    The ionic product of water, pK(w) = - log[H(+)][OH(-)] has been determined in aqueous solutions of tetramethylammonium chloride over the concentration range of 0.1-5.5 M at 25 degrees C using high-precision glass electrode potentiometric titrations. pK(w) data relating to aqueous potassium and sodium chlorides at ionic strengths up to 5 M are markedly lower than the tetramethylammonium chloride results. These differences are almost certainly due to weak associations between potassium and (especially) sodium and hydroxide ions.

  8. Ionometric determination of chloride ion in circulating and waste waters

    Energy Technology Data Exchange (ETDEWEB)

    Bebeshko, G.I.; Afanas' eva, V.I.; Danielova, I.I.; Dmitriev, M.A.; Radchenko, A.F.

    1986-09-01

    The authors attempt to develop selective ionometric methods to determine chloride ion in waste and circulating waters from technological ore processing, containing significant amounts of sulfide ion and various flotation reagents. These waters contain practically no cations that form hard to dissolve compounds with chloride ion such as Ag/sup +/, Cu/sup +/, Hg/sup +/ or Pb/sup 2 +/. The chloride ion concentration in water varies between 10 and 100 mg/liter. Information is shown on the concentration of the main anions and flotation reagents in waters that were analyzed.

  9. Stochastic Modeling of Reinforced Concrete Structures Exposed to Chloride Attack

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Frier, Christian

    2003-01-01

    concentration and reinforcement cover depth are modeled by stochastic fields. The paper contains a description of the parameters to be included in a stochastic model and a proposal for the information needed to obtain values for the parameters in order to be ab le to perform reliability investigations...... the reinforcement exceeds a critical threshold value. In the present paper a stochastic model is described by which the chloride content in a reinforced concrete structure can be estimated. The chloride ingress is modeled by a 2-dimensional diffusion process and the diffusion coefficient, surface chloride...

  10. Levels and sources of brominated flame retardants in human hair from urban, e-waste, and rural areas in South China.

    Science.gov (United States)

    Zheng, Jing; Luo, Xiao-Jun; Yuan, Jian-Gang; Wang, Jing; Wang, Yu-Tao; Chen, Shen-Jun; Mai, Bi-Xian; Yang, Zhong-Yi

    2011-12-01

    Human hair and indoor dust from urban, e-waste, and rural areas in south China were collected and analyzed for brominated flame retardants (BFRs). BFRs concentrations in hair from occupational e-waste recycling workers were higher than those from non-occupational exposed residents in other sampling areas. Polybrominated diphenyl ethers (PBDEs) and decabromodiphenyl ethane (DBDPE) are two major BFRs in hair samples. The PBDE congener profiles in hair from the e-waste area are different from those from urban and rural areas with relatively higher contribution of lower brominated congeners. DBDPE, instead of BDE209, has become the major BFR in non-e-waste recycling areas. Significant correlations were found between hair level and dust level for DBDPE and BTBPE but not for PBDEs. The different PBDE congener profiles between dust and hair may suggest that exogenous exposure to the PBDE adsorbed on dust is not a major source of hair PBDEs.

  11. Standard test method for determination of bromine and chlorine in UF6 and uranyl nitrate by X-Ray fluorescence (XRF) spectroscopy

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2001-01-01

    1.1 This method covers the determination of bromine (Br) and chlorine (Cl) in uranium hexafluoride (UF6) and uranyl nitrate solution. The method as written covers the determination of bromine in UF6 over the concentration range of 0.2 to 8 μg/g, uranium basis. The chlorine in UF6 can be determined over the range of 4 to 160 μg/g, uranium basis. Higher concentrations may be covered by appropriate dilutions. The detection limit for Br is 0.2 μg/g uranium basis and for Cl is 4 μg/g uranium basis. 1.2 This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  12. Chloride, bromide and iodide scintillators with europium

    Science.gov (United States)

    Zhuravleva, Mariya; Yang, Kan

    2016-09-27

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  13. Piezoresistive Properties of Polyvinyl Chloride Composites

    Science.gov (United States)

    Toprakci, Hatice Aylin Karahan

    Textile based sensors provide an interface between the user and the electronic system by converting any type of physiological or environmental signal into electrical signals. Common applications include health monitoring, rehabilitation, multimedia, and surveillance. In this research we demonstrate fabrication of piezoresistive sensors on textile fabrics through application of a screen-printed conductive nanocomposite layer of plasticized poly(vinyl chloride) (PVC), and carbon nanofiber (CNF). In order to understand the behavior of conductive plastisol, morphological, mechanical and electrical properties of composite films were investigated for different molecular weights of PVC. Homogeneous filler dispersion and good filler/polymer interphase were observed without any dominant filler orientation. Mechanical and electrical properties were found to be affected by CNF, plasticizer content and matrix molecular weight. CNFs were found to provide substantial bridging in the matrix and enhance strength. These nanostructured composite sensors were found to be sensitive under different levels of strain which can be monitored by change in electrical resistance. Finally, we demonstrate the fabrication of piezoresistive sensors on textile fabrics through application of a screen-printed conductive nanocomposite layer of conductive plastisol. Conductive plastisol was found to show good adhesion to fabric with homogeneous CNF distribution. As in composite films, samples were found to show negative piezoresistance at different levels of strain. Strain level and filler concentration were found to affect the piezoresistive behavior and sensitivity of the printed sensors.

  14. Analysis of brominated and phosphate-based flame retardants in polymer samples by HPLC-UV/MS and online-GPC-HPLC-UV

    Energy Technology Data Exchange (ETDEWEB)

    Schlummer, M.; Brandl, F. [Fraunhofer-Institut fuer Verfahrenstechnik und Verpackung (IVV), Freising (Germany); Maeurer, A.

    2004-09-15

    Here we present two analytical approaches for the identification and quantification of brominated and phosphate-based flame retardants. The first is an HPLC-UV/MS approach, which allows the separation and unequivocal identification and quantification of at least 15 different technical flame retardants. The second approach was set-up as a screening tool, consisting of a GPC separation coupled to an HPLC-UV device.

  15. Recent Development on Environmental Geochemistry of Bromine in Atmosphere%大气中溴的环境地球化学研究进展

    Institute of Scientific and Technical Information of China (English)

    彭炳先; 吴代赦; 李萍

    2011-01-01

    溴是大气平流层和对流层中的重要物种,能参与大气中的多种化学过程,对臭氧的损耗影响很大,同时也干扰大气的硫循环和汞循环,在大气化学中起着十分重要的作用.综述了近年来大气对流层和平流层溴的种类和含量、自然来源和人为来源,以及化学性质,并重点总结了活性溴物种BrO在大气中的存在情况及其在臭氧损耗中的作用.最后,提出了目前大气研究的不足之处和尚待深入开展研究的一些重要科学问题.%Bromine species are important components in troposphere and stratosphere, which can participate in many atmospheric chemical processes, play important role in the ozone depletion, and affect sulfur and mercury cycle of atmosphere. This paper provides an up-to-date overview of global bromine emissions from natural and anthropogenic sources, summarizes the level, species and chemistry of bromine in troposphere and stratosphere, and especially reviews the presence and important role of BrO of reactive bromine species in the ozone depletion. Finally,the shortcomings in current atmospheric research and prospect of main scientific problems are put forward.

  16. 溴制冷机的泄漏与防止%Cause Analysis and Protection of Leakage Occurred in Refrigeration Machine Using Bromine

    Institute of Scientific and Technical Information of China (English)

    张学滨; 陈洁

    2001-01-01

    本文介绍了溴制冷机泄漏的原因,对泄漏后引起故障进行了分析,并提出防止泄漏的措施。%The cause of the leakage occurred in the refrigeration machinesusing bromine was introduced in this article.Then,the result of the leakage was analyzed and the measures to protect the leakage were suggested.

  17. An X-ray photoelectron spectroscopy study of surface changes on brominated and sulfur-treated activated carbon sorbents during mercury capture: performance of pellet versus fiber sorbents.

    Science.gov (United States)

    Saha, Arindom; Abram, David N; Kuhl, Kendra P; Paradis, Jennifer; Crawford, Jenni L; Sasmaz, Erdem; Chang, Ramsay; Jaramillo, Thomas F; Wilcox, Jennifer

    2013-12-03

    This work explores surface changes and the Hg capture performance of brominated activated carbon (AC) pellets, sulfur-treated AC pellets, and sulfur-treated AC fibers upon exposure to simulated Powder River Basin-fired flue gas. Hg breakthrough curves yielded specific Hg capture amounts by means of the breakthrough shapes and times for the three samples. The brominated AC pellets showed a sharp breakthrough after 170-180 h and a capacity of 585 μg of Hg/g, the sulfur-treated AC pellets exhibited a gradual breakthrough after 80-90 h and a capacity of 661 μg of Hg/g, and the sulfur-treated AC fibers showed no breakthrough even after 1400 h, exhibiting a capacity of >9700 μg of Hg/g. X-ray photoelectron spectroscopy was used to analyze sorbent surfaces before and after testing to show important changes in quantification and oxidation states of surface Br, N, and S after exposure to the simulated flue gas. For the brominated and sulfur-treated AC pellet samples, the amount of surface-bound Br and reduced sulfur groups decreased upon Hg capture testing, while the level of weaker Hg-binding surface S(VI) and N species (perhaps as NH4(+)) increased significantly. A high initial concentration of strong Hg-binding reduced sulfur groups on the surface of the sulfur-treated AC fiber is likely responsible for this sorbent's minimal accumulation of S(VI) species during exposure to the simulated flue gas and is linked to its superior Hg capture performance compared to that of the brominated and sulfur-treated AC pellet samples.

  18. Polybrominated diphenyl ethers listed as Stockholm Convention POPs, other brominated flame retardants and heavy metals in e-waste polymers in Nigeria.

    Science.gov (United States)

    Sindiku, Omotayo; Babayemi, Joshua; Osibanjo, Oladele; Schlummer, Martin; Schluep, Mathias; Watson, Alan; Weber, Roland

    2015-10-01

    Polybrominated diphenyl ethers (PBDEs) were the first brominated persistent organic pollutants (POPs) listed in the Stockholm Convention. Parties to the convention are currently establishing inventories for developing action plans for the environmentally sound management of PBDE-containing materials. The major use of commercial octabromodiphenyl ether (c-OctaBDE) has been in casings from cathode ray tube (CRT) TVs and computer monitors. Large quantities of used e-waste and electronic equipment have been exported to developing countries with Nigeria being a major importer in Africa. The casings from 382 TVs and computers imported from major world regions to Nigeria were sampled in backyards and waste dumps. The samples were screened with X-ray flourescence (XRF) for bromine and analysed by gas chromatography/ electron capture detection (GC/ECD) for brominated flame retardants (BFRs). A high proportion of the CRT casings (61 %) contained more than 10,000 ppm bromine from BFRs. Decabromodiphenyl ether (DecaBDE) was the major flame retardant used in TV sets and tetrabromobisphenol A (TBBPA) for computer CRTs.The screening suggests that average PBDE levels (of c-OctaBDE + DecaBDE) in Nigerian-stockpiled CRT casings were 1.1 % for TV and 0.13 % for PC CRTs. These are above the Restriction of Hazardous Substances (RoHS) limit and should be separated for RoHS compliant recycling. The Nigerian e-waste inventory of 237,000 t of CRT plastic would therefore contain approx. 594 t c-OctaBDE and 1,880 t of DecaBDE. In Nigeria, as for most developing countries, there is currently no adequate e-waste management, plastic separation or destruction capacity. The data highlight the urgent need to develop environmentally sound management for this large material flow.

  19. Quorum sensing-disrupting brominated furanones protect the gnotobiotic brine shrimp Artemia franciscana from pathogenic Vibrio harveyi, Vibrio campbellii, and Vibrio parahaemolyticus isolates.

    Science.gov (United States)

    Defoirdt, Tom; Crab, Roselien; Wood, Thomas K; Sorgeloos, Patrick; Verstraete, Willy; Bossier, Peter

    2006-09-01

    Autoinducer 2 (AI-2) quorum sensing was shown before to regulate the virulence of Vibrio harveyi towards the brine shrimp Artemia franciscana. In this study, several different pathogenic V. harveyi, Vibrio campbellii, and Vibrio parahaemolyticus isolates were shown to produce AI-2. Furthermore, disruption of AI-2 quorum sensing by a natural and a synthetic brominated furanone protected gnotobiotic Artemia from the pathogenic isolates in in vivo challenge tests.

  20. Emissions of brominated flame retardants in Asia: consideration of its potential risk form the view point of the Norwegian regulation

    Science.gov (United States)

    Kikuchi, Ryunosuke; Gerardo, Romeu; Gorbacheva, Tamara

    2010-05-01

    Flame retardants can be divided into two broad categories: additive or reactive, which can be further more divided into brominated or non-brominated sub-categories. These retardants are found in many commercial products such as computers, television sets, furniture, carpets, etc. They are of environmental concern due to their persistence, potential for bioaccumulation and widespread distribution via atmospheric transport, and possible adverse effects in wildlife and humans. Tetrabromobisphenol-A (TBBPA) is mainly used in electrical and electronic appliances (circuit board in particular), and the application of TBBPA accounts for about two thirds of the global production of brominated flame retardant (BFR). The European Union Risk Assessment does not support the restriction of TBBPA: i.e. no risk is identified for the reactive use of TBBPA such as in epoxy resin used in circuit boards. By contrast, in 2007 Norway notified the World Trade Organization of its intention to prohibit 18 substances from consumer goods (Notification No. 2007/9016/N), called the Prohibition on Certain Hazardous Substances in Consumer Products (PoHS). TBBPA is listed in this prohibition list. Marine conservation is recognized as a key issue in Norwegian fishery management e.g. wastewater management in the framework of the North Sea Declarations. TBBPA is very water-soluble, and dimethyl-TBBPA is lipophilic and may accumulate in fat. TBBPA is not readily biodegradable and can have long-term effects in the aquatic environment. Norwegian examples are summarized: TBBPA was found in marine sediment samples from Tromsø harbor (northern Norway) and in Atlantic cod from Lofoten and Varanger; TBBPA has been detected in Norwegian peregrine falcon and golden eagle eggs; and TBBPA has been detected in the blood in the general population of Norway. From these viewpoints, it can be considered that Norway needs to strictly control TBBPA emissions. In recent times, Asia has emerged as one of the leading