WorldWideScience

Sample records for boron lined ionisation

  1. Ionisation chamber containing boron as a neutron detector in medical accelerator fields.

    Science.gov (United States)

    Zielczynski, M; Gryzinski, M A; Golnik, N; Tulik, P

    2007-01-01

    A combination of the recombination principle of H(10) measurements with the use of the ionisation chambers containing boron has been presented, in order to increase the relative sensitivity of the chamber to neutrons by a factor close to the radiation quality factor of photoneutrons. Three types of the chambers were investigated. Two of them were filled with BF(3) and the third one contained electrodes covered with B(4)C. All the chambers were placed in paraffin moderators. The response of the chambers was investigated, depending on gas pressure and polarising voltage. The results showed that it was possible to obtain nearly the same response of the chamber to H(10) for photons and neutrons in a restricted energy range; however, further investigations are needed to make an optimum design.

  2. Evidence for Ionised Accretion Discs in Five Narrow-Line Seyfert 1 Galaxies

    CERN Document Server

    Ballantyne, D R; Fabian, A C

    2000-01-01

    (Abridged) We present the results of fitting ASCA spectra of six narrow-line Seyfert 1 (NLS1) galaxies with the ionised reflection models of Ross & Fabian (1993). We find that five of the galaxies (TONS 180, PKS 0558-504, Ark 564, Mrk 335 and PG 1244+026) are well fit by the ionised disc model, and these are often better fits than the alternative models considered. The sixth galaxy, NGC 4051, has additional spectral complexity that cannot be well described by a simple ionised disc model or any of the other alternative models. All six of the NLS1s we considered show evidence for a broad Fe Kalpha line, but none of the line centroids are consistent with emission from highly ionised Fe. This is most likely due to the line being redshifted because of relativistic effects. We note that sources with larger ionisation parameters tend to have larger Fe Kalpha EWs. We interpret this as evidence that ionised Fe features are making their presence felt in the spectra. Since most of our sources have steep spectra, hig...

  3. Boron tolerance in NS wheat lines

    Directory of Open Access Journals (Sweden)

    Brdar Milka

    2006-01-01

    Full Text Available Boron is an essential micronutrient for higher plants. Present in excessive amounts boron becomes toxic and can limit plant growth and yield. Suppression of root growth is one of the symptoms of boron toxicity in wheat. This study was undertaken to investigate the response of 10 perspective NS lines of wheat to high concentrations of boron. Analysis of root growth was done on young plants, germinated and grown in the presence of different concentrations of boric acid (0, 50,100 and 150 mg/1. Significant differences occurred between analyzed genotypes and treatments regarding root length. Average suppression of root growth was between 11,6 and 34,2%, for line NS 252/02 are even noted 61,4% longer roots at treatments in relation to the control. Lines with mean suppression of root growth less than 20% (NS 101/02, NS 138/01, NS 53/03 and NS 73/02 may be considered as boron tolerant. Spearmans coefficients showed high level of agreement regarding rang of root length for genotypes treated with 100 and 150 mg H3BO3/l.

  4. Test of on-line alkali detector based on surface ionisation technique

    Energy Technology Data Exchange (ETDEWEB)

    Wiktorsson, L.-P.A.; Sjoestroem, L.K. [Chemical Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    1998-12-31

    The objective of this project is to test on-line alkali metal measuring equipment in a reducing atmosphere. The equipment is based on surface ionisation (SI) technique. The tests have taken place in reactors of varying sizes, from mg per batch to continuous feeding of kg/h, non-pressurised and pressurised. On-line alkali metal detector prototypes have been tested in real gases at atmospheric and elevated pressure. The primary parts of the detector prototypes are a platinum filament and an ion collector. The first prototype (A) of the surface ionisation detector was tested in a mg-scale pyrolysis reactor, a so-called Pyrojector, by introducing the coal sample with a `pelletizer`. The generated detector signal, a current in the pA to {mu}A range, was directly proportional to the sample weight. The second prototype (B) of the surface ionisation detector was tested in a very tarry gas flow, 20 g tar/Nm{sup 3}, at atmospheric pressure in a continuously fed g/min-scale biomass pyrolysis apparatus. The generated detector signal, a current in the {mu}A range, was measured by a picoammeter and sampled on a computer. The feedstocks were pine and birch and straw. A third prototype (D) of the surface ionisation detector was tested during pressurised gasification in a fluidised bed reactor. The feedstock was birch. The prototype detected alkali in the gas, though the temperature was only 773-793 K in the vicinity of the detector. The filament temperature control has to be further developed and tested. 1 ref., 19 figs., 6 tabs.

  5. P-MaNGA Galaxies: Emission Lines Properties - Gas Ionisation and Chemical Abundances from Prototype Observations

    CERN Document Server

    Belfiore, F; Bundy, K; Thomas, D; Maraston, C; Wilkinson, D; Sánchez, S F; Bershady, M; Blanc, G A; Bothwell, M; Cales, S L; Coccato, L; Drory, N; Emsellem, E; Fu, H; Gelfand, J; Law, D; Masters, K; Parejko, J; Tremonti, C; Wake, D; Weijmans, A; Yan, R; Xiao, T; Zhang, K; Zheng, T; Bizyaev, D; Kinemuchi, K; Oravetz, D; Simmons, A

    2014-01-01

    MaNGA (Mapping Nearby Galaxies at Apache Point Observatory) is a SDSS-IV survey that will obtain spatially resolved spectroscopy from 3600 \\AA\\ to 10300 \\AA\\ for a representative sample of over 10000 nearby galaxies. In this paper we present the analysis of nebular emission line properties using observations of 14 galaxies obtained with P-MaNGA, a prototype of the MaNGA instrument. By using spatially resolved diagnostic diagrams we find extended star formation in galaxies that are centrally dominated by Seyfert/LINER-like emission, illustrating that galaxy characterisations based on single fibre spectra are necessarily incomplete. We observe extended (up to $\\rm 1 R_{e}$) LINER-like emission in the central regions of three galaxies. We make use of the $\\rm EW(H \\alpha)$ to argue that the observed emission is consistent with ionisation from hot evolved stars. Using stellar population indices we conclude that galactic regions which are ionised by a Seyfert/LINER-like radiation field are also devoid of recent st...

  6. Evidence for an ionised disc in the narrow-line Seyfert 1 galaxy Ark 564

    CERN Document Server

    Vaughan, S; Reeves, J; Warwick, R; Edelson, R

    1999-01-01

    We present simultaneous ASCA and RXTE observations of Ark 564, the brightest known ``narrow-line'' Seyfert 1 in the 2-10 keV band. The measured X-ray spectrum is dominated by a steep (Gamma~2.7) power-law continuum extending to at least 20 keV, with imprinted Fe K-line and -edge features and an additional ``soft excess'' below ~1.5 keV. The energy of the iron K-edge indicates the presence of highly ionised material, which we identify in terms of reflection from a strongly irradiated accretion disc. The high reflectivity of this putative disc, together with its strong intrinsic O VIII Ly-alpha and O VIII recombination emission, can also explain much of the observed soft excess flux. Furthermore, the same spectral model also provides a reasonable match to the very steep 0.1-2 keV spectrum deduced from ROSAT data. The source is much more rapidly variable than ``normal'' Seyfert 1s of comparable luminosity, increasing by a factor of ~50% in 1.6 hours, with no measurable lag between the 0.5-2 keV and 3-12 keV band...

  7. Modelling of spectral lines emitted by hydrogen isotopes for ionising and recombining plasma conditions of Tokamak edges

    Energy Technology Data Exchange (ETDEWEB)

    Koubiti, M.; Marandet, Y.; Godbert-Mouret, L.; Stamm, R.; Touati, K. [Physique des Interactions Ioniques et Moleculaires, UMR 6633 CNRS/Universite de Provence, centre de Saint-Jerome, Marseille (Spain); Capes, H.; Escarguel, A.; Guirlet, R.; Michelis, C. De [Departement de Recherches sur la Fusion Controlee, Association EURATOM-CEA Cadrache, Saint Paul lez Durance (France)

    2001-07-01

    The plasma in the periphery of a magnetic fusion device plays an important role in the spread of particle and heat power. To optimise its role, it is necessary to characterize the edge plasma and understand all the interaction processes between the plasma constituents (ions, electrons and neutrals), and also their interactions with the device walls. For that purpose, high-resolution passive emission spectroscopy is well suitable since it is a non-intrusive method However, edge plasma diagnostics based on this method requires the accurate modelling of the observed spectra. A lineshape model initially developed for Stark broadening has been recently updated to include the Zeeman effect. The synthetic line profiles can be convolved with a Gaussian or a Lorentzian to account for the Doppler broadening and the instrumental function. For ionising conditions of edge plasmas such as those realized in front of the neutraliser plates (NP) of the Tore-Supra (TS) Ergodic Divertor where the electron temperature and density are usually higher than 10 eV and lower than 10{sup 19} m{sup -3}, the electron excitation of deuterium atoms dominates the recombination and only the first lines of the Balmer series are measured By fitting and analysing the spectrum of the deuterium Balmer {alpha} line (D{alpha}) emitted at different radial positions, information on the edge neutral populations can be obtained. In particular the neutral pro' auction mechanism and the dominant neutral relaxation processes can be identified from Doppler profile analysis. For this purpose we have analysed the lineshape of (D{alpha}) emitted in front of an equatorial NP of the ergodic diverter by a plasma region extending up to 2 cm radially away from the NP surface. For recombining plasma conditions such as Hose obtained in axisymmetric divertors, the electron temperature and density are respectively lower than 1 eV and higher than 10{sup 20} m{sup -3}, the volume recombination dominates the excitation

  8. Boron

    Science.gov (United States)

    ... an eye wash. Boron was used as a food preservative between 1870 and 1920, and during World Wars ... chemical symbol), B (symbole chimique), Borate, Borate de Sodium, Borates, Bore, Boric Acid, Boric Anhydride, Boric Tartrate, ...

  9. Looking into individual coffee beans during the roasting process: direct micro-probe sampling on-line photo-ionisation mass spectrometric analysis of coffee roasting gases.

    Science.gov (United States)

    Hertz-Schünemann, Romy; Streibel, Thorsten; Ehlert, Sven; Zimmermann, Ralf

    2013-09-01

    A micro-probe (μ-probe) gas sampling device for on-line analysis of gases evolving in confined, small objects by single-photon ionisation time-of-flight mass spectrometry (SPI-TOFMS) was developed. The technique is applied for the first time in a feasibility study to record the formation of volatile and flavour compounds during the roasting process within (inside) or in the direct vicinity (outside) of individual coffee beans. A real-time on-line analysis of evolving volatile and semi-volatile organic compounds (VOC and SVOC) as they are formed under the mild pyrolytic conditions of the roasting process was performed. The soft-ionisation mass spectra depict a molecular ion signature, which is well corresponding with the existing knowledge of coffee roasting and evolving compounds. Additionally, thereby it is possible to discriminate between Coffea arabica (Arabica) and Coffea canephora (Robusta). The recognized differences in the roasting gas profiles reflect the differences in the precursor composition of the coffee cultivars very well. Furthermore, a well-known set of marker compounds for Arabica and Robusta, namely the lipids kahweol and cafestol (detected in their dehydrated form at m/z 296 and m/z 298, respectively) were observed. If the variation in time of different compounds is observed, distinctly different evolution behaviours were detected. Here, phenol (m/z 94) and caffeine (m/z 194) are exemplary chosen, whereas phenol shows very sharp emission peaks, caffeine do not have this highly transient behaviour. Finally, the changes of the chemical signature as a function of the roasting time, the influence of sampling position (inside, outside) and cultivar (Arabica, Robusta) is investigated by multivariate statistics (PCA). In summary, this pilot study demonstrates the high potential of the measurement technique to enhance the fundamental knowledge of the formation processes of volatile and semi-volatile flavour compounds inside the individual coffee bean.

  10. Development and construction of a neutron beam line for accelerator-based boron neutron capture synovectomy.

    Science.gov (United States)

    Gierga, D P; Yanch, J C; Shefer, R E

    2000-01-01

    A potential application of the 10B(n, alpha)7Li nuclear reaction for the treatment of rheumatoid arthritis, termed Boron Neutron Capture Synovectomy (BNCS), is under investigation. In an arthritic joint, the synovial lining becomes inflamed and is a source of great pain and discomfort for the afflicted patient. The goal of BNCS is to ablate the synovium, thereby eliminating the symptoms of the arthritis. A BNCS treatment would consist of an intra-articular injection of boron followed by neutron irradiation of the joint. Monte Carlo radiation transport calculations have been used to develop an accelerator-based epithermal neutron beam line for BNCS treatments. The model includes a moderator/reflector assembly, neutron producing target, target cooling system, and arthritic joint phantom. Single and parallel opposed beam irradiations have been modeled for the human knee, human finger, and rabbit knee joints. Additional reflectors, placed to the side and back of the joint, have been added to the model and have been shown to improve treatment times and skin doses by about a factor of 2. Several neutron-producing charged particle reactions have been examined for BNCS, including the 9Be(p,n) reaction at proton energies of 4 and 3.7 MeV, the 9Be(d,n) reaction at deuteron energies of 1.5 and 2.6 MeV, and the 7Li(p,n) reaction at a proton energy of 2.5 MeV. For an accelerator beam current of 1 mA and synovial boron uptake of 1000 ppm, the time to deliver a therapy dose of 10,000 RBEcGy ranges from 3 to 48 min, depending on the treated joint and the neutron producing charged particle reaction. The whole-body effective dose that a human would incur during a knee treatment has been estimated to be 3.6 rem or 0.75 rem, for 1000 ppm or 19,000 ppm synovial boron uptake, respectively, although the shielding configuration has not yet been optimized. The Monte Carlo design process culminated in the construction, installation, and testing of a dedicated BNCS beam line on the high

  11. Modelling of spectral lines emitted by hydrogen isotopes for ionising and recombining plasma conditions of tokamak edges

    Energy Technology Data Exchange (ETDEWEB)

    Koubiti, M.; Marandet, Y.; Godbert-Mouret, L.; Stamm, R.; Touati, K. [Universite de Provence, Marseille (France). PIIM; Loch, S.; Summers, H.P. [Strathclyde Univ., Glasgow (United Kingdom). Dept. of Physics and Applied Physics; Meigs, A. [UKAEA-Euratom Fusion Association, Culham Science Centre, Abingdon (United Kingdom); Capes, H.; Escarguel, A.; Guirlet, R.; Michelis, C. de [Association Euratom-CEA, Centre d' Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. de Recherches sur la Fusion Controlee

    2002-07-01

    The plasma in the periphery or in a divertor chamber of a magnetic fusion device plays an important role in the spread of particle and heat power. Optimising the role of such a plasma requires its characterization and the understanding of all the mutual interactions of its constituents (ions, electrons, and neutrals), and also their interactions with the device materials. Among the various diagnostic methods, high-resolution passive spectroscopy is well suitable for such a purpose since it is non-intrusive. However, diagnostics based on this method requires an accurate modelling of the observed spectra. A fitting routine has been developed for the interpretation of D{alpha} spectra measured in front of a neutraliser plate of the Tore-Supra Ergodic Divertor. It takes into account both Zeeman and Doppler effects, the instrumental function, and the relaxation of the neutrals induced by elastic collisions with the plasma ions. On the other side, in order to study high-n Balmer lines and the continuum emission of deuterium in detached divertor plasmas, a more complex lineshape code developed for Stark broadening has been recently coupled to a code accounting for line-merging into the continuum. The code allows the convolution with a Gaussian (or a Lorentzian) to account for the Doppler broadening and the instrumental function. The Stark lineshape code has also been updated to include Zeeman effect and can be used for conditions where both Stark and Zeeman effects are important like in ITER-divertor plasmas. (orig.)

  12. First field application of a thermal desorption resonance-enhanced multiphoton-ionisation single particle time-of-flight mass spectrometer for the on-line detection of particle-bound polycyclic aromatic hydrocarbons.

    Science.gov (United States)

    Oster, Markus; Elsasser, Michael; Schnelle-Kreis, Jürgen; Zimmermann, Ralf

    2011-12-01

    The on-line analysis of single aerosol particles with mass spectrometrical methods is an important tool for the investigation of aerosols. Often, a single laser pulse is used for one-step laser desorption/ionisation of aerosol particles. Resulting ions are detected with time-of-flight mass spectrometry. With this method, the detection of inorganic compounds is possible. The detection of more fragile organic compounds and carbon clusters can be accomplished by separating the desorption and the ionisation in two steps, e.g. by using two laser pulses. A further method is, using a heated metal surface for thermal desorption of aerosol particles. If an ultraviolet laser is used for ionisation, a selective ionisation of polycyclic aromatic hydrocarbons (PAH) and alkylated PAH is possible via a resonance-enhanced multiphoton-ionisation process. Laser velocimetry allows individual laser triggering for single particles and additionally delivers information on aerodynamic particle diameters. It was shown that particles deriving from different combustion sources can be differentiated according to their PAH patterns. For example, retene, a C(4)-alkylated phenanthrene derivative, is a marker for the combustion of coniferous wood. In this paper, the first field application of a thermal desorption resonance-enhanced multiphoton-ionisation single particle time-of-flight mass spectrometer during a measurement campaign in Augsburg, Germany in winter 2010 is presented. Larger PAH-containing particles (i.e. with aerodynamic diameters larger than 1 μm), which are suspected to be originated by re-suspension processes of agglomerated material, were in the focus of the investigation. Due to the low concentration of these particles, an on-line virtual impactor enrichment system was used. The detection of particle-bound PAH in ambient particles in this larger size region was possible and in addition, retene could be detected on several particles, which allows to identify wood combustion as

  13. Use of GEANT4 vs. MCNPX for the characterization of a boron-lined neutron detector

    Science.gov (United States)

    van der Ende, B. M.; Atanackovic, J.; Erlandson, A.; Bentoumi, G.

    2016-06-01

    This work compares GEANT4 with MCNPX in the characterization of a boron-lined neutron detector. The neutron energy ranges simulated in this work (0.025 eV to 20 MeV) are the traditional domain of MCNP simulations. This paper addresses the question, how well can GEANT4 and MCNPX be employed for detailed thermal neutron detector characterization? To answer this, GEANT4 and MCNPX have been employed to simulate detector response to a 252Cf energy spectrum point source, as well as to simulate mono-energetic parallel beam source geometries. The 252Cf energy spectrum simulation results demonstrate agreement in detector count rate within 3% between the two packages, with the MCNPX results being generally closer to experiment than are those from GEANT4. The mono-energetic source simulations demonstrate agreement in detector response within 5% between the two packages for all neutron energies, and within 1% for neutron energies between 100 eV and 5 MeV. Cross-checks between the two types of simulations using ISO-8529 252Cf energy bins demonstrates that MCNPX results are more self-consistent than are GEANT4 results, by 3-4%.

  14. Water Stress and Foliar Boron Application Altered Cell Wall Boron and Seed Nutrition in Near-Isogenic Cotton Lines Expressing Fuzzy and Fuzzless Seed Phenotypes

    Science.gov (United States)

    2015-01-01

    Our previous research, conducted under well-watered conditions without fertilizer application, showed that fuzziness cottonseed trait resulted in cottonseed nutrition differences between fuzzy (F) and fuzzless (N) cottonseed. Under water stress conditions, B mobility is further limited, inhibiting B movement within the plant, affecting seed nutrition (quality). Therefore, we hypothesized that both foliar B and water stress can affect B mobility, altering cottonseed protein, oil, and mineral nutrition. The objective of the current research was to evaluate the effects of the fuzziness seed trait on boron (B) and seed nutrition under water stress and foliar B application using near-isogenic cotton lines (NILs) grown in a repeated greenhouse experiment. Plants were grown under-well watered conditions (The soil water potential was kept between -15 to -20 kPa, considered field capacity) and water stress conditions (soil water potential between -100 and -150 kPa, stressed conditions). Foliar B was applied at a rate of 1.8 kg B ha-1 as H3BO3. Under well-watered conditions without B the concentrations of seed oil in N lines were higher than in F lines, and seed K and N levels were lower in N lines than in F lines. Concentrations of K, N, and B in leaves were higher in N lines than in F lines, opposing the trend in seeds. Water-stress resulted in higher seed protein concentrations, and the contribution of cell wall (structural) B to the total B exceeded 90%, supporting the structural role of B in plants. Foliar B application under well-watered conditions resulted in higher seed protein, oil, C, N, and B in only some lines. This research showed that cottonseed nutrition differences can occur due to seed fuzziness trait, and water stress and foliar B application can alter cottonseed nutrition. PMID:26098564

  15. Water Stress and Foliar Boron Application Altered Cell Wall Boron and Seed Nutrition in Near-Isogenic Cotton Lines Expressing Fuzzy and Fuzzless Seed Phenotypes.

    Science.gov (United States)

    Bellaloui, Nacer; Turley, Rickie B; Stetina, Salliana R

    2015-01-01

    Our previous research, conducted under well-watered conditions without fertilizer application, showed that fuzziness cottonseed trait resulted in cottonseed nutrition differences between fuzzy (F) and fuzzless (N) cottonseed. Under water stress conditions, B mobility is further limited, inhibiting B movement within the plant, affecting seed nutrition (quality). Therefore, we hypothesized that both foliar B and water stress can affect B mobility, altering cottonseed protein, oil, and mineral nutrition. The objective of the current research was to evaluate the effects of the fuzziness seed trait on boron (B) and seed nutrition under water stress and foliar B application using near-isogenic cotton lines (NILs) grown in a repeated greenhouse experiment. Plants were grown under-well watered conditions (The soil water potential was kept between -15 to -20 kPa, considered field capacity) and water stress conditions (soil water potential between -100 and -150 kPa, stressed conditions). Foliar B was applied at a rate of 1.8 kg B ha(-1) as H3BO3. Under well-watered conditions without B the concentrations of seed oil in N lines were higher than in F lines, and seed K and N levels were lower in N lines than in F lines. Concentrations of K, N, and B in leaves were higher in N lines than in F lines, opposing the trend in seeds. Water-stress resulted in higher seed protein concentrations, and the contribution of cell wall (structural) B to the total B exceeded 90%, supporting the structural role of B in plants. Foliar B application under well-watered conditions resulted in higher seed protein, oil, C, N, and B in only some lines. This research showed that cottonseed nutrition differences can occur due to seed fuzziness trait, and water stress and foliar B application can alter cottonseed nutrition.

  16. Water Stress and Foliar Boron Application Altered Cell Wall Boron and Seed Nutrition in Near-Isogenic Cotton Lines Expressing Fuzzy and Fuzzless Seed Phenotypes.

    Directory of Open Access Journals (Sweden)

    Nacer Bellaloui

    Full Text Available Our previous research, conducted under well-watered conditions without fertilizer application, showed that fuzziness cottonseed trait resulted in cottonseed nutrition differences between fuzzy (F and fuzzless (N cottonseed. Under water stress conditions, B mobility is further limited, inhibiting B movement within the plant, affecting seed nutrition (quality. Therefore, we hypothesized that both foliar B and water stress can affect B mobility, altering cottonseed protein, oil, and mineral nutrition. The objective of the current research was to evaluate the effects of the fuzziness seed trait on boron (B and seed nutrition under water stress and foliar B application using near-isogenic cotton lines (NILs grown in a repeated greenhouse experiment. Plants were grown under-well watered conditions (The soil water potential was kept between -15 to -20 kPa, considered field capacity and water stress conditions (soil water potential between -100 and -150 kPa, stressed conditions. Foliar B was applied at a rate of 1.8 kg B ha(-1 as H3BO3. Under well-watered conditions without B the concentrations of seed oil in N lines were higher than in F lines, and seed K and N levels were lower in N lines than in F lines. Concentrations of K, N, and B in leaves were higher in N lines than in F lines, opposing the trend in seeds. Water-stress resulted in higher seed protein concentrations, and the contribution of cell wall (structural B to the total B exceeded 90%, supporting the structural role of B in plants. Foliar B application under well-watered conditions resulted in higher seed protein, oil, C, N, and B in only some lines. This research showed that cottonseed nutrition differences can occur due to seed fuzziness trait, and water stress and foliar B application can alter cottonseed nutrition.

  17. Porosity calculations using a C/O logging tool with boron-lined NaI detectors

    Energy Technology Data Exchange (ETDEWEB)

    Metwally, Walid A., E-mail: Walid.Metwally@GNF.co [Global Nuclear Fuel (GNF) 3901 Castle Hayne Road, M/C A-55 Wilmington, NC 28401 (United States)

    2011-01-15

    In the present work, a boron lining is added to a NaI detector assembly to study the possibility of combining both the C/O tool and the thermal neutron porosity tool in one tool, both of which are commonly used tools in oil well logging. The combined tool proposed in this paper was modeled with the general purpose Monte Carlo N-particle (MCNP) transport code. The simulation results show a good porosity sensitivity (especially to low porosity values). The results also show a great reduction in the neutron flux incident on the detectors and consequently the reduction of detector activation by thermal neutrons.

  18. Porosity calculations using a C/O logging tool with boron-lined NaI detectors.

    Science.gov (United States)

    Metwally, Walid A

    2011-01-01

    In the present work, a boron lining is added to a NaI detector assembly to study the possibility of combining both the C/O tool and the thermal neutron porosity tool in one tool, both of which are commonly used tools in oil well logging. The combined tool proposed in this paper was modeled with the general purpose Monte Carlo N-particle (MCNP) transport code. The simulation results show a good porosity sensitivity (especially to low porosity values). The results also show a great reduction in the neutron flux incident on the detectors and consequently the reduction of detector activation by thermal neutrons.

  19. On-line DLTS investigations of vacancy related defects in low-temperature electron irradiated, boron-doped Si

    Science.gov (United States)

    Zangenberg, N. R.; Nylandsted Larsen, A.

    2005-02-01

    Vacancy-related defects in Si are explored with deep level transient spectroscopy (DLTS). The measurements are performed on-line on irradiated p-type Si and a new trap with the signature (Epa, σpa) = (0.18 eV, 6.5×10-15 cm2) only present at cryogenic temperatures is studied. Furthermore, the bi-stable boron-vacancy complex is studied and it’s configuration at low temperatures is investigated and found to have the signature (Epa, σpa) = (0.11 eV, 8.2×10-15 cm2).

  20. Excitation wavelength dependence of water-window line emissions from boron-nitride laser-produced plasmas.

    Science.gov (United States)

    Crank, M; Harilal, S S; Hassan, S M; Hassanein, A

    2012-02-01

    We investigated the effects of laser excitation wavelength on water-window emission lines of laser-produced boron-nitride plasmas. Plasmas are produced by focusing 1064 nm and harmonically generated 532 and 266 nm radiation from a Nd:YAG laser on BN target in vacuum. Soft x-ray emission lines in the water-window region are recorded using a grazing-incidence spectrograph. Filtered photodiodes are used to obtain complementary data for water-window emission intensity and angular dependence. Spectral emission intensity changes in nitrogen Ly-α and He-α are used to show how laser wavelength affects emission. Our results show that the relative intensity of spectral lines is laser wavelength dependent, with the ratio of Ly-α to He-α emission intensity decreasing as laser wavelength is shortened. Filtered photodiode measurements of angular dependence showed that 266 and 532 nm laser wavelengths produce uniform emission.

  1. Selective on-line detection of boronic acids and derivatives in high-performance liquid chromatography eluates by post-column reaction with alizarin

    NARCIS (Netherlands)

    Duval, F.L.; Wardani, P.A.; Zuilhof, H.; Beek, van T.A.

    2015-01-01

    An on-line high-performance liquid chromatography (HPLC) method for the rapid and selective detection of boronic acids in complex mixtures was developed. After optimization experiments at an HPLC flow rate of 0.40 mL/min, the HPLC-separated analytes were mixed post-column with a solution of 75 µM al

  2. A NLTE line formation for neutral and singly-ionised titanium in model atmospheres of the reference A-K stars

    CERN Document Server

    Sitnova, T M; Ryabchikova, T A

    2016-01-01

    We construct a comprehensive model atom for TiI-II using more than 3600 measured and predicted energy levels of TiI and 1800 energy levels of TiII, and quantum mechanical photoionisation cross-sections. Non-local thermodynamical equilibrium (NLTE) line formation for the two ions of titanium is treated through a wide range of spectral types from A to K, including metal-poor stars with [Fe/H] down to -2.6 dex. NLTE leads to systematically depleted total absorption in the TiI lines and to positive abundance corrections. The magnitude of NLTE abundance corrections is smaller compared to the available literature data for the cool (FGK type) atmospheres. NLTE leads to strengthened TiII lines and to negative NLTE abundance corrections. For the first time, we performed the NLTE calculations for TiI-II in the 6500 K 4.1, and neglecting inelastic collisions with HI for the VMP giant HD 122563. For the very metal-poor turn-off stars ([Fe/H] < -2 and log g < 4.1), the abundance difference TiI-TiII was obtained to ...

  3. Photo-ionisation mass spectrometry as detection method for gas chromatography. Optical selectivity and multidimensional comprehensive separations.

    Science.gov (United States)

    Zimmermann, Ralf; Welthagen, Werner; Gröger, Thomas

    2008-03-14

    Mass spectrometry (MS) with soft ionisation techniques (i.e. ionisation without fragmentation of the analyte molecules) for gaseous samples exhibits interesting analytical properties for direct analysis applications (i.e. direct inlet mass spectrometric on-line monitoring) as well as mass spectrometric detection method for gas chromatography (GC-MS). Commonly either chemical ionisation (CI) or field ionisation (FI) is applied as soft ionisation technology for GC-MS. An interesting alternative to the CI and FI technologies methods are photo-ionisation (PI) methods. PI overcomes some of the limitations of CI and FI and furthermore add some unique analytical properties. The resonance enhanced multi-photon ionisation (REMPI) method uses intense UV-laser pulses (wavelength range approximately 350-193 nm) for highly selective, sensitive and soft ionisation of predominately aromatic compounds. The single photon ionisation (SPI) method utilises VUV light (from lamps or laser sources, wavelengths range approximately 150-110 nm) can be used for a universal soft ionisation of organic molecules. In this article the historical development as well as the current status and concepts of gas chromatography hyphenated to photo-ionisation mass spectrometry are reviewed.

  4. A gamma-ray telescope for on-line measurements of low boron concentrations in a head-phantom for BNCT

    Energy Technology Data Exchange (ETDEWEB)

    Verbakel, W.F.A.R.

    1996-06-01

    In Boron Neutron Capture Therapy the {sup 10}B(n, {alpha}){sup 7}Li reaction is used to create a tumour destructing field by the emitted high-LET (Linear Energy Transfer) particles. This reaction is accompanied by the emission of a photon of energy 478 keV. This can serve as a probe for detection of the reaction rate and thereby provide a tool to assess the boron concentration during therapy. An experimental configuration has been designed for on-line measurements of the {sup 10}B prompt gamma rays in a background of hydrogen neutron capture prompt gamma rays, neutrons and gamma rays coming from the reactor. At a facility with epithermal neutrons of the Low Flux Reactor a head phantom has been irradiated with neutorns. This phantom is filled with water and a small volume of 7.8 cm{sup 3} containing 62 ppm {sup 10}B, simulating a tumour. The experimental configuration for prompt gamma measurements has been expanded to perform tomography. The reconstruction of the position and the size of the tumour and its boron cencentration appeared to be possible. The first experiments at the therapy room in the High Flux Reactor showed that this method can probably be expanded for on-line monitoring of the total boron amount in a patients head. Next to this, Monte Carlo calculations and foil activation measurements have been performed to obtain the neutron spectrum of the epithermal beam of the LFR. With the insight achieved with these calculations it has been possible to optimize the total neutron flux. By introduction of a graphite scatter in the beam tube close to the reactr core, the flux has been rainsed with about 65%. With the computer code DORT neutron distributions over the phantom have been calculated for 47 energy groups. These calculations are necessary for ultimate boron tomography. (orig.).

  5. Selective on-line detection of boronic acids and derivatives in high-performance liquid chromatography eluates by post-column reaction with alizarin.

    Science.gov (United States)

    Duval, Florine; Wardani, Puspita A; Zuilhof, Han; van Beek, Teris A

    2015-10-23

    An on-line high-performance liquid chromatography (HPLC) method for the rapid and selective detection of boronic acids in complex mixtures was developed. After optimization experiments at an HPLC flow rate of 0.40 mL/min, the HPLC-separated analytes were mixed post-column with a solution of 75 μM alizarin and 0.1% triethylamine in acetonitrile, which was delivered at a flow rate of 0.60 mL/min. The reaction between alizarin and boronic acids occurred in a reaction coil of dimensions of 3.5 m × 0.25 mm at a temperature of 50 °C, resulting in fluorescent complexes that were detected as positive peaks by a fluorescence detector (λexc 469 nm and λe m 610 nm). The method enabled the selective detection of various boronic acids and derivatives, with a limit of detection of phenylboronic acid of 1.2 ng or 1 μM. It could successfully monitor the progress of two organic reactions involving boronic acid-containing compounds, and provided useful insights into the course of the reactions. Copyright © 2015 Elsevier B.V. All rights reserved.

  6. Cosmic-ray ionisation in collapsing clouds

    CERN Document Server

    Padovani, Marco; Galli, Daniele

    2013-01-01

    Cosmic rays (CR) play an important role in dense molecular cores, affecting their thermal and dynamical evolution and initiating the chemistry. Several studies have shown that the formation of protostellar discs in collapsing clouds is severely hampered by the braking torque exerted by the entrained magnetic field on the infalling gas, as long as the field remains frozen to the gas. We examine the possibility that the concentration and twisting of the field lines in the inner region of collapse can produce a significant reduction of the ionisation fraction. To check whether the CR ionisation rate (CRir) can fall below the critical value required to maintain good coupling, we first study the propagation of CRs in a model of a static magnetised cloud varying the relative strength of the toroidal/poloidal components and the mass-to-flux ratio. We then follow the path of CRs using realistic magnetic field configurations generated by numerical simulations of a rotating collapsing core. We find that an increment of...

  7. A γ-ray telescope for on-line measurements of low boron concentrations in a head phantom for BNCT

    Science.gov (United States)

    Verbakel, W. F. A. R.; Stecher-Rasmussen, F.

    1997-02-01

    In Boron Neutron Capture Therapy the 10B(n, α)7 Li reaction is used to create a tumour-destructing field of high Linear Energy Transfer (LET) particles. The therapy requires a high boron concentration in the tumour and a low boron concentration in the healthy tissue. The boron neutron capture reaction is accompanied by the emission of a photon of energy 478 keV. It is investigated whether measuring of these photons can serve as a tool to determine the boron concentration during therapy in the tumour as well as in the healthy tissue. Such a measurement is complicated by the presence of a large background photon field. To study the feasibility, an experimental configuration has been designed at a test facility of the Low-Flux Reactor (LFR). The LFR provides an epithermal neutron beam for irradiation of a head phantom which simulates a human head with a tumour. This paper shows that the reconstruction of the position and the size of the tumour as well as the ratio of the boron concentrations appeared to be possible. In a second stage it is shown that these measurements can be expanded to experiments with the therapy neutron beam of the High-Flux Reactor (HFR).

  8. Radiative effects of tropospheric ionisation

    Directory of Open Access Journals (Sweden)

    K. L. Aplin

    2003-06-01

    Full Text Available Despite the increasing evidence that cosmic ray variations may influence clouds and climate, there has been little discussion of the direct radiative effects of atmospheric ionisation. Laboratory experiments show that hydrated molecular cluster-ions, formed in the atmosphere by cosmic rays, absorb in the infra-red continuum at wavelengths of 9–12 μm. The tropospheric magnitude of this effect is estimated: transmittance anomalies from clear sky ion concentrations peak at ~2% at 10 km in the mid-latitudes. A simple isothermal clear sky atmospheric model suggests the integrated effect of the absorption is ~2 Wm−2. The effect appears detectable in existing surface data sets; surface micrometeorological data shows a significant anticorrelation between downwelling infra-red radiation and atmospheric cosmic ray ionisation. This is consistent with the infra-red attenuation observed in laboratory studies of cluster-ion absorption. If atmospheric ionisation from cosmic rays has universally direct radiative effects, then reinterpretation of satellite cloud data may be necessary.

  9. A Preliminary experimental study of the boron concentration in vapor and the isotopic A preliminary experimental study of the boron concentrationin vapor and the isotopic fractionation of boron betweenseawater and vapor during evaporation of seawater

    Institute of Scientific and Technical Information of China (English)

    XIAO; Yingkai

    2001-01-01

    [1]Gast, J. A., Thompson, T. G., Evaporation of boric acid from seawater, Tellus, 1959, 6: 344-347.[2]Nishimura, M., Tanaka, K., Seawater may not be a source of boron in the atmosphere, J. Geoph. Res., 1972, 77: 5239-5242.[3]Fogg, T. R., Duce, R. A., Fasching, J. L., Sampling and determination of boron in the atmosphere, Anal. Chem., 1983, 55:2179-2184.[4]Fogg, T. R., Duce, R. A., Boron in the troposphere: Distribution and fluxes, J. Geoph. Res., 1985, 90: 3781-3796.[5]Spivack, A. J., Berndt, M. E., Seyfreid, W. E., Boron isotope fractionation during supercritical phase separation, Geochim.Cosmochim. Acta, 1990, 54: 2337-2339.[6]Palmer, M. R., London, D., Morgan, G. B. et al., Experimental determination of fractionation of 11B/10B between tourma-line and aqueous vapor: A temperature and pressure-dependent isotopic system, Chem. Geol., 1992, 101:123-129.[7]Hervig, R. L., London, D., Morgan, G. B. et al., Large boron isotope fractionation between hydrous vapor and silicate meltat igneous temperatures, in the Seventh Annual V. M. Goldschmidt Conf., LPI Contribution No. 921, Houston: Lunar and Planetary Institute, 1997, 93-94.[8]Vengosh, A., Starinsky, A., Kolodny, Y. et al., Boron isotope variations during fractional evaporation of seawater: New constraints on the marine vs. nonmarine debate, Geology, 1992, 20: 799-802.[9]Zhang, X. P., Shi, Y. E, Yao, T. D., The variation characteristics of δo18O in precipitation in Northeastern Qing-Zhang Plateau, Science in China, Series B (in Chinese), 1995, 25(5): 540-547.[10]Yu, J. S., Yu, E J., Liu, D. P., The hydrogen and oxygen of isotopic compositions of meteoric water in the eastern part of China, Geochimica (in Chinese), 1987, (1): 22-26.[11]Xiao, Y. K., Xiao, Y., Swihart, G. H. et al., Separation of boron by ion exchange with boron specific resin, Acta Geosci.Sinica (in Chinese), 1997, 18: 286-289.[12]Kiss, E., Ion-exchange separation and spectrophotometric determination of

  10. Measurement of in-phantom neutron flux and gamma dose in Tehran research reactor boron neutron capture therapy beam line

    OpenAIRE

    Elham Bavarnegin; Alireza Sadremomtaz; Hossein Khalafi; Yaser Kasesaz

    2016-01-01

    Aim: Determination of in-phantom quality factors of Tehran research reactor (TRR) boron neutron capture therapy (BNCT) beam. Materials and Methods: The doses from thermal neutron reactions with 14N and 10B are calculated by kinetic energy released per unit mass approach, after measuring thermal neutron flux using neutron activation technique. Gamma dose is measured using TLD-700 dosimeter. Results: Different dose components have been measured in a head phantom which has been designed an...

  11. Space-Confined Synthesis of Three-Dimensional Boron/Nitrogen-Doped Carbon Nanotubes/Carbon Nanosheets Line-in-Wall Hybrids and Their Electrochemical Energy Storage Applications

    DEFF Research Database (Denmark)

    Zhu, Shan; Li, Jiajun; Li, Qingfeng

    2016-01-01

    This research demonstrates a flexible one-pot strategy for fabricating three-dimensional (3D) boron/nitrogen-doped networks of carbon nanotubes(CNTs)/carbon nanosheets "Line-in-Wall" hybrids (LIWNB) based on the space-confined template method. In the synthesis, the high rate of freezing step...... and CNTs in this unique pattern, the LIW-NB integrates advantages of three aspects: first, the doped heteroatoms enhancing electrochemical properties of carbon matrix; second, the warp-proof nanosheets supplying high specific surface area; and the extracted and embedded CNTs serving as electron conductive...... and freeze-dried process enable the CNTs and carbon-heteroatoms sources confined in the limited space of the self-assembled NaCl salts, which are then heat-treated to obtain a B/N-doped network constructed by "Line-in-Wall" type of carbon hybrids. By combining the 3D B/N-doped carbon nanosheets network...

  12. Boron reclamation

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.M.

    1980-07-01

    A process to recover high purity /sup 10/B enriched crystalline boron powder from a polymeric matrix was developed on a laboratory basis and ultimately scaled up to production capacity. The process is based on controlled pyrolysis of boron-filled scrap followed by an acid leach and dry sieving operation to return the powder to the required purity and particle size specifications. Typically, the recovery rate of the crystalline powder is in excess of 98.5 percent, and some of the remaining boron is recovered in the form of boric acid. The minimum purity requirement of the recovered product is 98.6 percent total boron.

  13. Bioaerosol detection by aerosol TOF-mass spectrometry: Application of matrix assisted laser desorption/ionisation

    NARCIS (Netherlands)

    Wuijckhuijse, A.L. van; Stowers, M.A.; Kientz, Ch.E.; Marijnissen, J.C.M.; Scarlett, B.

    2000-01-01

    In previous publications the use of an aerosol time of flight mass spectrometer was reported for the on-line measurements of aerosols (Weiss 1997, Kievit 1995). The apparatus is capable of measuring the size as well as the chemical composition, by the use of Laser Desorption/Ionisation (LDI), of an

  14. Nucleation in an ultra low ionisation environment

    DEFF Research Database (Denmark)

    Enghoff, Martin Andreas Bødker

    In this work we have studied aerosol formation at ultra-low ionisation levels, using the existing deep underground science facility at Boulby mine, UK. At 1100 m depth, with a corresponding factor 106 reduction in cosmic ray muon flux, the Boulby facility is an ideal place to study the role of ions...

  15. Ionising radiation exposure in the Netherlands

    NARCIS (Netherlands)

    Eleveld H; LSO

    2003-01-01

    The Dutch population is exposed to ionising radiation from various sources, both natural and man-made. This is a review of the radiation exposure for members of the public from all sources for the year 2000. The average annual effective dose per capita is estimated at 2.5 mSv, which is almost the

  16. European Code against Cancer 4th Edition: Ionising and non-ionising radiation and cancer.

    Science.gov (United States)

    McColl, Neil; Auvinen, Anssi; Kesminiene, Ausrele; Espina, Carolina; Erdmann, Friederike; de Vries, Esther; Greinert, Rüdiger; Harrison, John; Schüz, Joachim

    2015-12-01

    Ionising radiation can transfer sufficient energy to ionise molecules, and this can lead to chemical changes, including DNA damage in cells. Key evidence for the carcinogenicity of ionising radiation comes from: follow-up studies of the survivors of the atomic bombings in Japan; other epidemiological studies of groups that have been exposed to radiation from medical, occupational or environmental sources; experimental animal studies; and studies of cellular responses to radiation. Considering exposure to environmental ionising radiation, inhalation of naturally occurring radon is the major source of radiation in the population - in doses orders of magnitude higher than those from nuclear power production or nuclear fallout. Indoor exposure to radon and its decay products is an important cause of lung cancer; radon may cause approximately one in ten lung cancers in Europe. Exposures to radon in buildings can be reduced via a three-step process of identifying those with potentially elevated radon levels, measuring radon levels, and reducing exposure by installation of remediation systems. In the 4th Edition of the European Code against Cancer it is therefore recommended to: "Find out if you are exposed to radiation from naturally high radon levels in your home. Take action to reduce high radon levels". Non-ionising types of radiation (those with insufficient energy to ionise molecules) - including extremely low-frequency electric and magnetic fields as well as radiofrequency electromagnetic fields - are not an established cause of cancer and are therefore not addressed in the recommendations to reduce cancer risk.

  17. Flash ionisation signature in coherent cyclotron emission from Brown Dwarfs

    CERN Document Server

    Vorgul, Irena

    2016-01-01

    Brown dwarfs form mineral clouds in their atmospheres, where charged particles can produce large-scale discharges in form of lightning resulting in a substantial sudden increase of local ionisation. Brown dwarfs are observed to emit cyclotron radio emission. We show that signatures of strong transient atmospheric ionisation events (flash ionisation) can be imprinted on a pre-existing radiation. Detection of such flash ionisation events will open investigations into the ionisation state and atmospheric dynamics. Such ionisation events can also result from explosion shock waves, bursts or eruptions. We present an analytical model that describes the modulation of a pre-existing electromagnetic radiation by a time-dependent (flash) conductivity that is characteristic for flash ionisation events like lightning. Our conductivity model reproduces the conductivity function derived from observations of Terrestrial Gamma Ray Flashes, and is applicable to astrophysical objects with strong temporal variations in the loca...

  18. Ionisation Potentials of Metal Carbide Clusters

    Science.gov (United States)

    Dryza, Viktoras; Addicoat, M.; Gascooke, Jason; Buntine, Mark; Metha, Gregory

    2006-03-01

    Photo-Ionisation Efficiency (PIE) experiments have been performed on gas phase niobium and tantalum carbide clusters to determine their ionisation potentials (IPs). For TanCm (n = 3-4, m = 0-4) clusters an oscillatory behaviour is observed such that clusters with an odd number of carbon atoms have higher IPs and clusters with an even number of carbons have lower IPs. Excellent agreement is found with relative IPs calculated using density functional theory for the lowest energy structures, which are consistent with the development of a 2x2x2 face-centred nanocrystal. For the niobium carbide clusters we observe the species Nb4C5 and Nb4C6. Initial calculations suggest that these clusters contain carbon-carbon bonding. Interestingly, the stoichiometry for Nb4C6 is half that of a metcar, M8C12. Preliminary data will also be shown on bimetallic-carbide clusters.

  19. The ionising radiations: a daily reality

    Directory of Open Access Journals (Sweden)

    Eduardo Gallego Díaz

    2010-12-01

    Full Text Available This paper introduce the nature of the radioactive substances and of the ionising radiation, the effects that they cause on the matter and the available media for their detection and measure, as well as the sources of natural radiation, to which the human being are exposed. Next, in the more detailed part of this paper, it is described the wide range of ionising radiations uses in: medicine, agriculture, earth sciences, biology and in some other scientific fields, that allow to pose its impact in the perspective of facing the ones from natural sources. The article concludes that for avoiding damages it is necessary proper protection against the radioactive substances, but avoiding limitation their beneficial uses in the various ranges described. For finishing this paper, the basic principles of radiation protection are described, due to they are the its principal aim.

  20. Food ionisation. Realities and perspectives; L'ionisation alimentaire. Realites et perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Bonnet, G

    1994-06-01

    The ionisation of food is a treatment using a certain type of energy. the radiations used in the industrial treatments are limited to three sources. The gamma radiations, the x radiations and the electrons beams emitted with accelerators. The physical treatments by ionizing radiations have for aim to cleanse and to increase the conservation time of food. Now, the applications in agriculture and food industry, are still marginal. The industrial using ionisation are these ones that did not find any alternative decontamination method. The barriers are more scientific or technical or economical than a question of regulation or behaviour. (N.C.)

  1. No evidence for large-scale outflows in the extended ionised halo of ULIRG Mrk273

    CERN Document Server

    Spence, R A W; Tadhunter, C N; Rose, M; Cabrera-Lavers, A; Spoon, H; Munoz-Tunon, C

    2016-01-01

    We present deep new GTC/OSIRIS narrow-band images and optical WHT/ISIS long-slit spectroscopy of the merging system Mrk273 that show a spectacular extended halo of warm ionised gas out to a radius of $\\sim45$ kpc from the system nucleus. Outside of the immediate nuclear regions (r > 6 kpc), there is no evidence for kinematic disturbance in the ionised gas: in the extended regions covered by our spectroscopic slits the emission lines are relatively narrow (FWHM $\\lesssim$ 350 km$\\rm s^{-1}$) and velocity shifts small (|$\\Delta$V| $\\lesssim{} $250 km$\\rm s^{-1}$). This is despite the presence of powerful near-nuclear outflows (FWHM > 1000 km$\\rm s^{-1}$; |$\\Delta$V| > 400 km$\\rm s^{-1}$; r < 6 kpc). Diagnostic ratio plots are fully consistent with Seyfert 2 photo-ionisation to the NE of the nuclear region, however to the SW the plots are more consistent with low-velocity radiative shock models. The kinematics of the ionised gas, combined with the fact that the main structures are aligned with low-surface-bri...

  2. Muon Ionisation Cooling in Reduced RF

    CERN Document Server

    Prior, G

    2010-01-01

    In Muon Ionisation Cooling, closely packed high-field RF cavities are interspersed with energy-absorbing material in order to reduce particle beam emittance. Transverse focussing of the muon beams is achieved by superconducting magnets. This results in the RF cavities sitting in intense magnetic fields. Recent studies have shown that this may limit the peak gradient that can be achieved in the RF cavities. In this paper, we study the effect that a reduced RF gradient may have on the cooling performance of the Neutrino Factory lattice and examine methods to mitigate the effect.

  3. Crystalline boron nitride aerogels

    Science.gov (United States)

    Zettl, Alexander K.; Rousseas, Michael; Goldstein, Anna P.; Mickelson, William; Worsley, Marcus A.; Woo, Leta

    2017-04-04

    This disclosure provides methods and materials related to boron nitride aerogels. In one aspect, a material comprises an aerogel comprising boron nitride. The boron nitride has an ordered crystalline structure. The ordered crystalline structure may include atomic layers of hexagonal boron nitride lying on top of one another, with atoms contained in a first layer being superimposed on atoms contained in a second layer.

  4. Crystalline boron nitride aerogels

    Energy Technology Data Exchange (ETDEWEB)

    Zettl, Alexander K.; Rousseas, Michael; Goldstein, Anna P.; Mickelson, William; Worsley, Marcus A.; Woo, Leta

    2017-04-04

    This disclosure provides methods and materials related to boron nitride aerogels. In one aspect, a material comprises an aerogel comprising boron nitride. The boron nitride has an ordered crystalline structure. The ordered crystalline structure may include atomic layers of hexagonal boron nitride lying on top of one another, with atoms contained in a first layer being superimposed on atoms contained in a second layer.

  5. Boron Nitride Nanotubes

    Science.gov (United States)

    Smith, Michael W. (Inventor); Jordan, Kevin (Inventor); Park, Cheol (Inventor)

    2012-01-01

    Boron nitride nanotubes are prepared by a process which includes: (a) creating a source of boron vapor; (b) mixing the boron vapor with nitrogen gas so that a mixture of boron vapor and nitrogen gas is present at a nucleation site, which is a surface, the nitrogen gas being provided at a pressure elevated above atmospheric, e.g., from greater than about 2 atmospheres up to about 250 atmospheres; and (c) harvesting boron nitride nanotubes, which are formed at the nucleation site.

  6. Boron nitride composites

    Energy Technology Data Exchange (ETDEWEB)

    Kuntz, Joshua D.; Ellsworth, German F.; Swenson, Fritz J.; Allen, Patrick G.

    2017-02-21

    According to one embodiment, a composite product includes: a matrix material including hexagonal boron nitride and one or more borate binders; and a plurality of cubic boron nitride particles dispersed in the matrix material. According to another embodiment, a composite product includes: a matrix material including hexagonal boron nitride and amorphous boron nitride; and a plurality of cubic boron nitride particles dispersed in the matrix material.

  7. Connecting the dots: a correlation between ionising radiation and cloud mass-loss rate traced by optical integral field spectroscopy

    CERN Document Server

    McLeod, A F; Dale, J E; Ginsburg, A; Klaassen, P D; Mottram, J C; Preibisch, T; Ramsay, S; Reiter, M; Testi, L

    2016-01-01

    We present an analysis of the effect of feedback from O- and B-type stars with data from the integral field spectrograph MUSE mounted on the Very Large Telescope of pillar-like structures in the Carina Nebular Complex, one of the most massive star-forming regions in the Galaxy. For the observed pillars, we compute gas electron densities and temperatures maps, produce integrated line and velocity maps of the ionised gas, study the ionisation fronts at the pillar tips, analyse the properties of the single regions, and detect two ionised jets originating from two distinct pillar tips. For each pillar tip we determine the incident ionising photon flux $Q_\\mathrm{0,pil}$ originating from the nearby massive O- and B-type stars and compute the mass-loss rate $\\dot{M}$ of the pillar tips due to photo-evaporation caused by the incident ionising radiation. We combine the results of the Carina data set with archival MUSE data of a pillar in NGC 3603 and with previously published MUSE data of the Pillars of Creation in M...

  8. An important step forward in continuous spectroscopic imaging of ionising radiations using ASICs

    CERN Document Server

    Fessler, P; Eberle, H; Raad-Iseli, C D; Hilt, B; Huss, D; Krummenacher, F; Lutz, Jean Robert; Prevot, G; Renouprez, Albert Jean; Sigward, M H; Schwaller, B; Voltolini, C

    1999-01-01

    Characterization results are given for an original ASIC allowing continuous acquisition of ionising radiation images in spectroscopic mode. Ionising radiation imaging in general and spectroscopic imaging in particular must primarily be guided by the attempt to decrease statistical noise, which requires detection systems designed to allow very high counting rates. Any source of dead time must therefore be avoided. Thus, the use of on-line corrections of the inevitable dispersion of characteristics between the large number of electronic channels of the detection system, shall be precluded. Without claiming to achieve ultimate noise levels, the work described is focused on how to prevent good individual acquisition channel noise performance from being totally destroyed by the dispersion between channels without introducing dead times. With this goal, we developed an automatic charge amplifier output voltage offset compensation system which operates regardless of the cause of the offset (detector or electronic). ...

  9. Non-targeted effects of ionising radiation—Implications for low dose risk

    DEFF Research Database (Denmark)

    Kadhim, Munira; Salomaa, Sisko; Wright, Eric

    2013-01-01

    Non-DNA targeted effects of ionising radiation, which include genomic instability, and a variety of bystander effects including abscopal effects and bystander mediated adaptive response, have raised concerns about the magnitude of low-dose radiation risk. Genomic instability, bystander effects...... with respect to systemic (human health) consequences at low and intermediate doses of ionising radiation. Other outstanding questions include links between the different non-targeted responses and the variations in response observed between individuals and cell lines, possibly a function of genetic background......) Integrated Project funded by the European Union. Here we critically examine the evidence for non-targeted effects, discuss apparently contradictory results and consider implications for low-dose radiation health effects. © 2012 Elsevier B.V. All rights reserved....

  10. Methods of forming boron nitride

    Science.gov (United States)

    Trowbridge, Tammy L; Wertsching, Alan K; Pinhero, Patrick J; Crandall, David L

    2015-03-03

    A method of forming a boron nitride. The method comprises contacting a metal article with a monomeric boron-nitrogen compound and converting the monomeric boron-nitrogen compound to a boron nitride. The boron nitride is formed on the same or a different metal article. The monomeric boron-nitrogen compound is borazine, cycloborazane, trimethylcycloborazane, polyborazylene, B-vinylborazine, poly(B-vinylborazine), or combinations thereof. The monomeric boron-nitrogen compound is polymerized to form the boron nitride by exposure to a temperature greater than approximately 100.degree. C. The boron nitride is amorphous boron nitride, hexagonal boron nitride, rhombohedral boron nitride, turbostratic boron nitride, wurzite boron nitride, combinations thereof, or boron nitride and carbon. A method of conditioning a ballistic weapon and a metal article coated with the monomeric boron-nitrogen compound are also disclosed.

  11. Methods of forming boron nitride

    Energy Technology Data Exchange (ETDEWEB)

    Trowbridge, Tammy L; Wertsching, Alan K; Pinhero, Patrick J; Crandall, David L

    2015-03-03

    A method of forming a boron nitride. The method comprises contacting a metal article with a monomeric boron-nitrogen compound and converting the monomeric boron-nitrogen compound to a boron nitride. The boron nitride is formed on the same or a different metal article. The monomeric boron-nitrogen compound is borazine, cycloborazane, trimethylcycloborazane, polyborazylene, B-vinylborazine, poly(B-vinylborazine), or combinations thereof. The monomeric boron-nitrogen compound is polymerized to form the boron nitride by exposure to a temperature greater than approximately 100.degree. C. The boron nitride is amorphous boron nitride, hexagonal boron nitride, rhombohedral boron nitride, turbostratic boron nitride, wurzite boron nitride, combinations thereof, or boron nitride and carbon. A method of conditioning a ballistic weapon and a metal article coated with the monomeric boron-nitrogen compound are also disclosed.

  12. Ionisation clusters at DNA level: experimental modelling

    Energy Technology Data Exchange (ETDEWEB)

    Pszona, S.; Kula, J

    2002-07-01

    The importance of initial clustered damage to DNA is a hypothesis, which has to be approached also from physical modelling of the initial products of single charged particle interaction with DNA. A new tool for such studies, presented here, is based on modelling of the ionisation patterns resulting from a single charged particle crossing a nitrogen cavity of nanometre size. The nanometre size sites equivalent in unit density to DNA and nucleosome, have been modelled in a device, called a Jet Counter, consisting of a pulse operated valve which inject nitrogen in the form of an expansion jet into a interaction chamber. The distributions of the number of ions in a cluster created by a single alpha particle of 4.6 MeV along 0.15 nm to 13 nm size in nitrogen have been measured. A new descriptor of radiation action at DNA level is proposed. (author)

  13. The ionised, radical and molecular Milky Way: spectroscopic surveys with the SKA

    CERN Document Server

    Thompson, Mark; Dickinson, Clive; Mottram, Joseph C; Klaassen, Pamela; Ginsburg, Adam; Longmore, Steve; Remijan, Anthony; Menten, Karl

    2014-01-01

    The bandwith, sensitivity and sheer survey speed of the SKA offers unique potential for deep spectroscopic surveys of the Milky Way. Within the frequency bands available to the SKA lie many transitions that trace the ionised, radical and molecular components of the interstellar medium and which will revolutionise our understanding of many physical processes. In this chapter we describe the impact on our understanding of the Milky Way that can be achieved by spectroscopic SKA surveys, including "out of the box" early science with radio recombination lines, Phase 1 surveys of the molecular ISM using anomalous formaldehyde absorption, and full SKA surveys of ammonia inversion lines.

  14. On the Ionisation of Warm Opaque Interstellar Clouds and the Intercloud Medium

    CERN Document Server

    Sciama, Dennis William

    1997-01-01

    In this paper we use a number of observations to construct an integrated picture of the ionisation in the interiors of quiescent warm opaque interstellar clouds and in the intercloud medium (ICM) outside dense HII regions and hot dilute bubbles. Our main conclusion is that within $\\sim$ 1kpc of the sun the ionisation rate of hydrogen per unit volume in both the interiors of such clouds and in the ICM is independent of the local density of neutral hydrogen, and varies with position by less than $\\sim$ 20 per cent. These conclusions strongly favour the decaying neutrino hypothesis for the ionisation of the interstellar medium in these regions. Our analysis is based on a variety of observations, of which the most remarkable is the discovery by Spitzer and Fitzpatrick (1993) that, in the four slowly moving clouds along the line of sight to the halo star HD93521, the column densities of both SII and CII$^*$, which individually range over a factor $\\sim$4, are proportional to the column density of HI to within $\\si...

  15. New low-frequency electromagnetic modes associated with neutral dynamics in partially ionised plasma

    Directory of Open Access Journals (Sweden)

    A. A. Shaikh

    2013-05-01

    Full Text Available We have investigated the low frequency electromagnetic (EM modes in inhomogeneous, magnetised partially ionised plasma by incorporating neutral dynamics. We have derived a general EM dispersion relation by using a two-fluids magnetohydrodynamics (MHD model. Our analysis shows that the neutral dynamics is playing an extremely important role in the physics of magnetised partially ionised plasma by giving rise to new kind of EM modes. We found (1 the new instability is linked with compressibility of neutral particles, the collision between neutral and charged species and the relative streaming in hot/cold, inhomogeneous, magnetised partially ionised plasma, (2 and that neutral dynamics is responsible for the modified (complex inertial effect on magnetic field lines. Its consequences on the propagation characteristics of Alfvén wave and cyclotron frequency are discussed. Furthermore, a new mode similar to the Langmuir mode is reported. Finally, we discuss our results, for limiting cases, that may be appropriate for applications to space plasma environments including probable mechanism of escaping H+ and O− from the Martian atmosphere.

  16. Total ionisation cross sections in (e/sup +/-Li) scattering

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, K.K.; Mazumdar, P.S.

    1988-06-28

    Total ionisation cross sections for the positron impact ionisation of the lithium atom are calculated using a distorted-wave approximation in which both the effect of screening in the final state of the system and the distortion of the outgoing waves are taken into account. The present results are different from those using the first Born approximation and from an earlier distorted-wave calculation by other workers.

  17. IFU Spectroscopy of Southern Planetary Nebulae V: Low-Ionisation Structures

    Science.gov (United States)

    Ali, A.; Dopita, M. A.

    2017-08-01

    In this fifth paper of the series, we examine the spectroscopy and morphology of four southern Galactic planetary nebulae Hen 2-141, NGC 5307, IC 2553, and PB 6 using new integral field spectroscopy data. The morphologies and ionisation structures of the sample are given as a set of emission-line maps. In addition, the physical conditions, chemical compositions, and kinematical characteristics of these objects are derived. The results show that PB 6 and Hen 2-141 are of very high excitation classes and IC 2553 and NGC 5307 are mid to high excitation objects. The elemental abundances reveal that PB 6 is of Type I, Hen 2-141 and IC 2553 are of Type IIa, and NGC 5307 is of Type IIb/III. The observations unveil the presence of well-defined low-ionisation structures or `knots' in all objects. The diagnostic diagrams reveal that the excitation mechanism of these knots is probably by photoionisation of dense material by the nebular central stars. The physical analysis of six of these knots show no significant differences with their surrounding nebular gas, except their lower electron densities. In spite of the enhancement of the low-ionisation emission lines of these knots, their chemical abundances are nearly comparable to their surrounding nebulae, with the exception of perhaps slightly higher nitrogen abundances in the NGC 5307 knots. The integrated spectrum of IC 2553 reveals that nearly all key lines that have led researchers to characterise its central star as a weak-emission line star type are in fact of nebular origin.

  18. Boron nitride converted carbon fiber

    Science.gov (United States)

    Rousseas, Michael; Mickelson, William; Zettl, Alexander K.

    2016-04-05

    This disclosure provides systems, methods, and apparatus related to boron nitride converted carbon fiber. In one aspect, a method may include the operations of providing boron oxide and carbon fiber, heating the boron oxide to melt the boron oxide and heating the carbon fiber, mixing a nitrogen-containing gas with boron oxide vapor from molten boron oxide, and converting at least a portion of the carbon fiber to boron nitride.

  19. The properties of the extended warm ionised gas around low-redshift QSOs and the lack of extended high-velocity outflows

    CERN Document Server

    Husemann, B; Sánchez, S F; Jahnke, K

    2012-01-01

    (Abridged) We present a detailed analysis of a large sample of 31 low-redshift, mostly radio-quiet type 1 QSOs observed with integral field spectroscopy to study their extended emission-line regions (EELRs). We focus on the ionisation state of the gas, size and luminosity of extended narrow line regions (ENLRs), which corresponds to those parts of the EELR dominated by ionisation from the QSO, as well as the kinematics of the ionised gas. We detect EELRs around 19 of our 31 QSOs (61%) after deblending the unresolved QSO emission and the extended host galaxy light in the integral field data. We identify 13 EELRs to be entirely ionised by the QSO radiation, 3 EELRs are composed of HII regions and 3 EELRs display signatures of both ionisation mechanisms at different locations. The typical size of the ENLR is 10kpc at a median nuclear [OIII] luminosity of log(L([OIII])/[erg/s])=42.7+-0.15. We show that the ENLR sizes are least a factor of 2 larger than determined with HST, but are consistent with those of recentl...

  20. Boron-10 ABUNCL Active Testing

    Energy Technology Data Exchange (ETDEWEB)

    Kouzes, Richard T.; Ely, James H.; Lintereur, Azaree T.; Siciliano, Edward R.

    2013-07-09

    The Department of Energy Office of Nuclear Safeguards and Security (NA-241) is supporting the project Coincidence Counting With Boron-Based Alternative Neutron Detection Technology at Pacific Northwest National Laboratory (PNNL) for the development of a 3He proportional counter alternative neutron coincidence counter. The goal of this project is to design, build and demonstrate a system based upon 10B-lined proportional tubes in a configuration typical for 3He-based coincidence counter applications. This report provides results from testing of the active mode of the General Electric Reuter-Stokes Alternative Boron-Based Uranium Neutron Coincidence Collar (ABUNCL) at Los Alamos National Laboratory using sources and fuel pins.

  1. Spatially resolved study of the physical properties of the ionised gas in NGC 595

    CERN Document Server

    Relano, M; Vilchez, J M; Kennicutt, R C

    2009-01-01

    We present Integral Field Spectroscopy (IFS) of NGC 595, one of the most luminous HII regions in M33. This type of observations allows studying the variation of the principal emission line ratios across the surface of the nebula. At each position of the field of view, we fit the main emission line features of the spectrum within the spectral range 3650-6990A, and create maps of the principal emission line ratios for the total surface of the region. The extinction map derived from the Balmer decrement and the absorbed H-alpha luminosity show good spatial correlation with the 24 micron emission from Spitzer. We also show here the capability of the IFS to study the existence of Wolf-Rayet (WR) stars, identifying the previously catalogued WRs and detecting a new candidate towards the north of the region. The ionisation structure of the region nicely follows the H-alpha shell morphology and is clearly related to the location of the central ionising stars. The electron density distribution does not show strong vari...

  2. Glioblastoma stem cells: radiobiological response to ionising radiations of different qualities.

    Science.gov (United States)

    Pecchia, I; Dini, V; Ricci-Vitiani, L; Biffoni, M; Balduzzi, M; Fratini, E; Belli, M; Campa, A; Esposito, G; Cirrone, G; Romano, F; Stancampiano, C; Pelacchi, F; Pallini, R; Tabocchini, M A

    2015-09-01

    Glioblastoma multiforme (GBM) is the most common and malignant primary brain tumour, with very poor prognosis. The high recurrence rate and failure of conventional treatments are expected to be related to the presence of radio-resistant cancer stem cells (CSCs) inside the tumour mass. CSCs can both self-renew and differentiate into the heterogeneous lineages of cancer cells. Recent evidence showed a higher effectiveness of C-ions and protons in inactivating CSCs, suggesting a potential advantage of Hadrontherapy compared with conventional radiotherapy for GBM treatment. To investigate the mechanisms involved in the molecular and cellular responses of CSCs to ionising radiations, two GBM stem cell (GSC) lines, named lines 1 and 83, which were derived from patients with different clinical outcomes and having different metabolic profiles (as shown by NMR spectroscopy), were irradiated with (137)Cs photons and with protons or C-ions of 62 MeV u(-1) in the dose range of 5-40 Gy. The biological effects investigated were: cell death, cell cycle progression, and DNA damage induction and repair. Preliminary results show a different response to ionising radiation between the two GSC lines for the different end points investigated. Further experiments are in progress to consolidate the data and to get more insights on the influence of radiation quality.

  3. Invasive oral cancer stem cells display resistance to ionising radiation.

    Science.gov (United States)

    Gemenetzidis, Emilios; Gammon, Luke; Biddle, Adrian; Emich, Helena; Mackenzie, Ian C

    2015-12-22

    There is a significant amount of evidence to suggest that human tumors are driven and maintained by a sub-population of cells, known as cancer stem cells (CSC). In the case of head and neck cancer, such cells have been characterised by high expression levels of CD44 cell surface glycoprotein, while we have previously shown the presence of two diverse oral CSC populations in vitro, with different capacities for cell migration and proliferation. Here, we examined the response of oral CSC populations to ionising radiation (IR), a front-line measure for the treatment of head and neck tumors. We show that oral CSC initially display resistance to IR-induced growth arrest as well as relative apoptotic resistance. We propose that this is a result of preferential activation of the DNA damagerepair pathway in oral CSC with increased activation of ATM and BRCA1, elevated levels of DNA repair proteins RAD52, XLF, and a significantly faster rate of DNA double-strand-breaks clearance 24 hours following IR. By visually identifying CSC sub-populations undergoing EMT, we show that EMT-CSC represent the majority of invasive cells, and are more radio-resistant than any other population in re-constructed 3D tissues. We provide evidence that IR is not sufficient to eliminate CSC in vitro, and that sensitization of CD44hi/ESAlow cells to IR, followed by secondary EMT blockade, could be critical in order to reduce primary tumor recurrence, but more importantly to be able to eradicate cells capable of invasion and distant metastasis.

  4. Boron in sillimanite.

    Science.gov (United States)

    Grew, E S; Hinthorne, J R

    1983-08-05

    Sillimanite in six granulite-facies, kornerupine-bearing rocks contains 0.035 to 0.43 percent B(2)O(3) and 0.02 to 0.23 percent MgO (by weight). Substitution of boron for silicon and magnesium for aluminum is coupled such that the ratio of magnesium to boron is about 0.5. Sillimanite incorporates more than 0.1 percent B(2)O(3) only at high temperatures in a boron-rich environment at very low partial pressures of water. In the amphibolite facies, the sillimanite boron contents are too low to appreciably affect the stability relations of sillimanite with kyanite and andalusite.

  5. The effectiveness of photocatalytic ionisation disinfection of filter materials.

    Science.gov (United States)

    Pietrzak, Katarzyna; Gutarowska, Beata

    2013-01-01

    The purpose of this study was to determine the effectiveness of photocatalytic ionisation as a disinfection method for filter materials contaminated by microorganisms, and to assess how air relative humidity (RH), time and microbe type influence the effectiveness of this disinfection. In the quantitative analysis of a used car air filter, bacterial contamination equalled 1.2 x 10(5) cfu/cm2, fungal contamination was 3.8 x 10(6) cfu/cm2, and the isolated microorganisms were Aspergillus niger, Bacillus megaterium, Cladosporium herbarum, Cryptococcus laurenti, Micrococcus sp., Rhodotorula glutinis and Staphylococcus cohnii. In the model experiment, three isolates (C. herbarum, R. glutinis, S. cohnii) and 3 ATCC species (A. niger, E. coli, S. aureus) were used for photocatalytic ionisation disinfection. The conditions of effective photocatalytic ionisation disinfection (R > or = 99.9%) were established as 2-3 h at RH = 77% (bacteria) and 6-24 h at RH = 53% (fungi). RH has an influence on the effectiveness of the photocatalytic disinfection process; the highest effectiveness was obtained for bacteria at RH = 77%, with results 5% higher than for RH = 49%. The studies show that the sensitivity of microorganisms to photocatalytic ionisation disinfection is ordered as follows: Gram-positive bacteria (S. cohnii, S. aureus), Gram-negative bacteria (E. coli), yeasts (R. glutinis), and moulds (C. herbarum, A. niger). Of all the mathematical models used for the description of death dynamics after photocatalytic ionisation disinfection, the Chick-Watson model is the most useful, but for more resistant microorganisms, the delayed Chick-Watson model is highly recommended. It therefore seems, that the presented disinfection method of photocatalytic ionisation can be successfully used to clean filtration materials.

  6. Charge transfer and ionisation by intermediate-energy heavy ions.

    Science.gov (United States)

    Toburen, L H; McLawhorn, S L; McLawhorn, R A; Evans, N L; Justiniano, E L B; Shinpaugh, J L; Schultz, D R; Reinhold, C O

    2006-01-01

    The use of heavy ion beams for microbeam studies of mammalian cell response leads to a need to better understand interaction cross sections for collisions of heavy ions with tissue constituents. For ion energies of a few MeV u(-1) or less, ions capture electrons from the media in which they travel and undergo subsequent interactions as partially 'dressed' ions. For example, 16 MeV fluorine ions have an equilibrium charge of 7(+), 32 MeV sulphur ions have an equilibrium charge of approximately 11(+), and as the ion energies decrease the equilibrium charge decreases dramatically. Data for interactions of partially dressed ions are extremely rare, making it difficult to estimate microscopic patterns of energy deposition leading to damage to cellular components. Such estimates, normally obtained by Monte Carlo track structure simulations, require a comprehensive database of differential and total ionisation cross sections as well as charge transfer cross sections. To provide information for track simulation, measurement of total ionisation cross sections have been initiated at East Carolina University using the recoil ion time-of-flight method that also yields cross sections for multiple ionisation processes and charge transfer cross sections; multiple ionisation is prevalent for heavy ion interactions. In addition, measurements of differential ionisation cross sections needed for Monte Carlo simulation of detailed event-by-event particle tracks are under way. Differential, total and multiple ionisation cross sections and electron capture and loss cross sections measured for C(+) ions with energies of 100 and 200 keV u(-1) are described.

  7. Ionisation and the Formation of Low-Mass Protostars

    Science.gov (United States)

    Wurster, James; Bate, M. R.; Price, D. J.

    2017-06-01

    Molecular clouds are known to have strong magnetic fields and low ionisation rates. Numerical simulations performed with these more realistic conditions yield results closer to those observed, and furthermore, suggest additional observational signatures not yet explored. I will discuss my simulations of the formation of a single protostar starting from one solar mass of gas; the models include a self-consistent treatment of all three non-ideal MHD processes. My focus will be on how the ionisation parameters and non-ideal MHD processes affect the formation of the protostar and its environment.

  8. [Bipolar ionisation of indoor air through ion generators mountable into inflow ventilation and conditioning].

    Science.gov (United States)

    Dudarev, A A; Spichkin, G L; Denisikhina, D M; Burtsev, S I

    2010-01-01

    Experimental studies and digital modelling of artificial indoor air ionisation through bipolar ionisers mountable into inflow ventilation and conditioning proved possible creation of continuous even bipolar ion background in indoor air, similar to the natural one.

  9. Kinematic alignment of non-interacting CALIFA galaxies: Quantifying the impact of bars on stellar and ionised gas velocity field orientations

    CERN Document Server

    Barrera-Ballesteros, J K; García-Lorenzo, B; van de Ven, G; Aguerri, J A L; Mendez-Abreu, J; Spekkens, K; Sánchez, S F; Husemann, B; Mast, D; García-Benito, R; Iglesias-Paramo, J; del Olmo, A; Márquez, I; Masegosa, J; Kehrig, C; Marino, R A; Verdes-Montenegro, L; Ziegler, B; MacIntosh, D H; Bland-Hawthorn, J; Walcher, C J

    2014-01-01

    We present 80 stellar and ionised gas velocity maps from the Calar Alto Legacy Integral Field Area (CALIFA) survey in order to characterize the kinematic orientation of non-interacting galaxies. The study of galaxies in isolation is a key step towards understanding how fast-external processes, such as major mergers, affect kinematic properties in galaxies. We derived the global and individual (projected approaching and receding sides) kinematic position angles (PAs) for both the stellar and ionised gas line-of-sight velocity distributions. When compared to the photometric PA, we find that morpho-kinematic differences are smaller than 22 degrees in 90% of the sample for both components; internal kinematic misalignments are generally smaller than 16 degrees. We find a tight relation between the global stellar and ionised gas kinematic PA consistent with circular-flow pattern motions in both components. This relation also holds generally in barred galaxies across the bar and galaxy disk scales. Our findings sugg...

  10. 用于 n/γ混合场测量的涂硼电离室研制%Development of Boron-lined Ionization Chamber Used in n/γ Mixed Field

    Institute of Scientific and Technical Information of China (English)

    朱立; 魏志勇; 陈国云; 雷升杰; 方美华; 贾文宝; 张紫霞; 府宇

    2013-01-01

    研制了一种能同时测量混合场中γ和中子注量率的涂硼电离室,并实验测试了其性能。涂硼电离室由两个大小和结构一致的腔室组成:1个仅对γ灵敏,另1个对γ与中子均灵敏。用强度为2.7×107 s-1的Am-Be源测得电离室的中子灵敏度达9.2×10-16 A/(cm-2· s-1),在剂量率为5.24μGy/h的137 Csγ场中,电离室的γ灵敏度达7.36×10-16 A/(MeV · cm -2· s-1)。涂硼电离室 I-V 曲线坪长为600 V ,坪斜小于4%/100 V ,在工作电压为-400 V时,其γ补偿修正系数<5%,可用于核设施周围的混合场监测。%A boron-lined ionization chamber used in n/γ mixed field with better performance was developed .The boron-lined ionization chamber consists of two cavity rooms with the same size:One is for γ ,the other is for both γ and neutron .The neutron sensitivity reaches a level of 9.2 × 10 -16 A/(cm -2 · s-1 ) with a calibrated Am-Be neutron source with neutron intensity estimated to be 2.7 × 107 s-1 , and the γsensitivity reaches a level of 7.36 × 10 -16 A/(MeV · cm -2 · s-1 ) with a calibrated 137 Cs source with 5.24 μGy/h dose rate .The plateau length is 600 V and the slope is less than 4% /100 V .An average γ compensation coefficient is less than 5% at work voltage of-400 V ,w hich can be used to monitor the n/γ mixed field around reactors .

  11. Boron isotope determinations in waters and other geological materials: analytical techniques and inter-calibration of measurements.

    Science.gov (United States)

    Tonarini, Sonia; Pennisi, Maddalena; Gonfiantini, Roberto

    2009-06-01

    The (11)B/(10)B ratio exhibits wide variations in nature; thus, boron isotopes have found numerous applications in geochemistry, hydrology, and environmental studies. The main analytical techniques used are as follows: positive thermal ionisation mass spectrometry is the most precise (about 0.2 per thousand of the boron isotope ratio), but requires complex and laborious sample preparation; negative thermal ionisation mass spectrometry is less precise (about 0.5 per thousand), but rapid and suitable for water samples, whereas total evaporation-NTIMS allows for identification of the precise boron isotope composition of marine carbonates. It is expected that multi-collection system inductively coupled plasma mass spectrometry (MC-ICPMS) will eventually combine high precision with simple analytical procedures. Secondary ion mass spectrometry and laser ablation (LA)-MC-ICPMS allow in situ determinations on solid samples, but require the availability of calibration materials which are chemically and mineralogically similar to samples. These features of boron isotope measurement techniques were confirmed by the results of the first inter-laboratory comparison of measurements, organised by the Istituto di Geoscienze e Georisorse in Pisa. Finally, two examples of boron isotope applications in groundwater investigations are reported.

  12. An important step forward in continuous spectroscopic imaging of ionising radiations using ASICs

    Energy Technology Data Exchange (ETDEWEB)

    Fessler, P. [11 rue Rabelais, 92170 Vanves (France); Coffin, J. [Institut de Recherches Subatomiques, B.P. 28, 67037 Strasbourg (France); Eberle, H. [Institut de Recherches Subatomiques, B.P. 28, 67037 Strasbourg (France); Raad Iseli, C. de [Smart Silicon Systems SA, Ch. de la Graviere 6, CH-1007 Lausanne (Switzerland); Hilt, B. [Universite de Haute-Alsace, GRPHE, 61, rue Albert Camus, 68093 Mulhouse (France); Huss, D. [Universite de Haute-Alsace, GRPHE, 61, rue Albert Camus, 68093 Mulhouse (France); Krummenacher, F. [Smart Silicon Systems SA, Ch. de la Graviere 6, CH-1007 Lausanne (Switzerland); Lutz, J.R. [Institut de Recherches Subatomiques, B.P. 28, 67037 Strasbourg (France); Prevot, G. [Institut de Recherches Subatomiques, B.P. 28, 67037 Strasbourg (France); Renouprez, A. [Institut de Recherche sur la Catalyse, 2 Avenue Albert Einstein, 69626 Villeurbanne (France); Sigward, M.H. [Institut de Recherches Subatomiques, B.P. 28, 67037 Strasbourg (France); Schwaller, B. [Universite de Haute-Alsace, GRPHE, 61, rue Albert Camus, 68093 Mulhouse (France); Voltolini, C. [Institut de Recherches Subatomiques, B.P. 28, 67037 Strasbourg (France)

    1999-01-21

    Characterization results are given for an original ASIC allowing continuous acquisition of ionising radiation images in spectroscopic mode. Ionising radiation imaging in general and spectroscopic imaging in particular must primarily be guided by the attempt to decrease statistical noise, which requires detection systems designed to allow very high counting rates. Any source of dead time must therefore be avoided. Thus, the use of on-line corrections of the inevitable dispersion of characteristics between the large number of electronic channels of the detection system, shall be precluded. Without claiming to achieve ultimate noise levels, the work described is focused on how to prevent good individual acquisition channel noise performance from being totally destroyed by the dispersion between channels without introducing dead times. With this goal, we developed an automatic charge amplifier output voltage offset compensation system which operates regardless of the cause of the offset (detector or electronic). The main performances of the system are the following: the input equivalent noise charge is 190 e rms (input non connected, peaking time 500 ns), the highest gain is 255 mV/fC, the peaking time is adjustable between 200 ns and 2 {mu}s and the power consumption is 10 mW per channel. The agreement between experimental data and theoretical simulation results is excellent.

  13. Boron and the kidney.

    Science.gov (United States)

    Pahl, Madeleine V; Culver, B Dwight; Vaziri, Nosratola D

    2005-10-01

    Boron, the fifth element in the periodic table, is ubiquitous in nature. It is present in food and in surface and ocean waters, and is frequently used in industrial, cosmetic, and medical settings. Exposure to boron and related compounds has been recently implicated as a potential cause of chronic kidney disease in Southeast Asia. This observation prompted the present review of the published data on the effects of acute and chronic exposure to boron on renal function and structure in human beings and in experimental animals.

  14. Innovative method for boron extraction from iron ore containing boron

    Science.gov (United States)

    Wang, Guang; Wang, Jing-song; Yu, Xin-yun; Shen, Ying-feng; Zuo, Hai-bin; Xue, Qing-guo

    2016-03-01

    A novel process for boron enrichment and extraction from ludwigite based on iron nugget technology was proposed. The key steps of this novel process, which include boron and iron separation, crystallization of boron-rich slag, and elucidation of the boron extraction behavior of boron-rich slag by acid leaching, were performed at the laboratory. The results indicated that 95.7% of the total boron could be enriched into the slag phase, thereby forming a boron-rich slag during the iron and slag melting separation process. Suanite and kotoite were observed to be the boron-containing crystalline phases, and the boron extraction properties of the boron-rich slag depended on the amounts and grain sizes of these minerals. When the boron-rich slag was slowly cooled to 1100°C, the slag crystallized well and the efficiency of extraction of boron (EEB) of the slag was the highest observed in the present study. The boron extraction property of the slow-cooled boron-rich slag obtained in this study was much better than that of szaibelyite ore under the conditions of 80% of theoretical sulfuric acid amount, leaching time of 30 min, leaching temperature of 40°C, and liquid-to-solid ratio of 8 mL/g.

  15. Boron-Based Drug Design.

    Science.gov (United States)

    Ban, Hyun Seung; Nakamura, Hiroyuki

    2015-06-01

    The use of the element boron, which is not generally observed in a living body, possesses a high potential for the discovery of new biological activity in pharmaceutical drug design. In this account, we describe our recent developments in boron-based drug design, including boronic acid containing protein tyrosine kinase inhibitors, proteasome inhibitors, and tubulin polymerization inhibitors, and ortho-carborane-containing proteasome activators, hypoxia-inducible factor 1 inhibitors, and topoisomerase inhibitors. Furthermore, we applied a closo-dodecaborate as a water-soluble moiety as well as a boron-10 source for the design of boron carriers in boron neutron capture therapy, such as boronated porphyrins and boron lipids for a liposomal boron delivery system.

  16. LINES

    Directory of Open Access Journals (Sweden)

    Minas Bakalchev

    2015-10-01

    Full Text Available The perception of elements in a system often creates their interdependence, interconditionality, and suppression. The lines from a basic geometrical element have become the model of a reductive world based on isolation according to certain criteria such as function, structure, and social organization. Their traces are experienced in the contemporary world as fragments or ruins of a system of domination of an assumed hierarchical unity. How can one release oneself from such dependence or determinism? How can the lines become less “systematic” and forms more autonomous, and less reductive? How is a form released from modernistic determinism on the new controversial ground? How can these elements or forms of representation become forms of action in the present complex world? In this paper, the meaning of lines through the ideas of Le Corbusier, Leonidov, Picasso, and Hitchcock is presented. Spatial research was made through a series of examples arising from the projects of the architectural studio “Residential Transformations”, which was a backbone for mapping the possibilities ranging from playfulness to exactness, as tactics of transformation in the different contexts of the contemporary world.

  17. Boron nitride composites

    Science.gov (United States)

    Kuntz, Joshua D.; Ellsworth, German F.; Swenson, Fritz J.; Allen, Patrick G.

    2016-02-16

    According to one embodiment, a composite product includes hexagonal boron nitride (hBN), and a plurality of cubic boron nitride (cBN) particles, wherein the plurality of cBN particles are dispersed in a matrix of the hBN. According to another embodiment, a composite product includes a plurality of cBN particles, and one or more borate-containing binders.

  18. Boron nitride composites

    Energy Technology Data Exchange (ETDEWEB)

    Kuntz, Joshua D.; Ellsworth, German F.; Swenson, Fritz J.; Allen, Patrick G.

    2016-02-16

    According to one embodiment, a composite product includes hexagonal boron nitride (hBN), and a plurality of cubic boron nitride (cBN) particles, wherein the plurality of cBN particles are dispersed in a matrix of the hBN. According to another embodiment, a composite product includes a plurality of cBN particles, and one or more borate-containing binders.

  19. Magnetorotational instability in stratified, weakly ionised accretion discs

    CERN Document Server

    Salmeron, Roberto Aureliano; Salmeron, Raquel; Wardle, Mark

    2003-01-01

    We present a linear analysis of the vertical structure and growth of the magnetorotational instability in stratified, weakly ionised accretion discs, such as protostellar and quiescent dwarf novae systems. The method includes the effects of the magnetic coupling, the conductivity regime of the fluid and the strength of the magnetic field, which is initially vertical. The conductivity is treated as a tensor and assumed constant with height. We obtained solutions for the structure and growth rate of global unstable modes for different conductivity regimes, strengths of the initial magnetic field and coupling between ionised and neutral components of the fluid. The envelopes of short-wavelenght perturbations are determined by the action of competing local growth rates at different heights, driven by the vertical stratification of the disc. Ambipolar diffusion perturbations peak consistently higher above the midplane than modes including Hall conductivity. For weak coupling, perturbations including the Hall effec...

  20. Fully kinetic simulations of magnetic reconnection in partially ionised gases

    Science.gov (United States)

    Innocenti, M. E.; Jiang, W.; Lapenta, G.; Markidis, S.

    2016-12-01

    Magnetic reconnection has been explored for decades as a way to convert magnetic energy into kinetic energy and heat and to accelerate particles in environments as different as the solar surface, planetary magnetospheres, the solar wind, accretion disks, laboratory plasmas. When studying reconnection via simulations, it is usually assumed that the plasma is fully ionised, as it is indeed the case in many of the above-mentioned cases. There are, however, exceptions, the most notable being the lower solar atmosphere. Small ionisation fractions are registered also in the warm neutral interstellar medium, in dense interstellar clouds, in protostellar and protoplanetary accreditation disks, in tokamak edge plasmas and in ad-hoc laboratory experiments [1]. We study here how magnetic reconnection is modified by the presence of a neutral background, i.e. when the majority of the gas is not ionised. The ionised plasma is simulated with the fully kinetic Particle-In-Cell (PIC) code iPic3D [2]. Collisions with the neutral background are introduced via a Monte Carlo plug-in. The standard Monte Carlo procedure [3] is employed to account for elastic, excitation and ionization electron-neutral collisions, as well as for elastic scattering and charge exchange ion-neutral collisions. Collisions with the background introduce resistivity in an otherwise collisionless plasma and modifications of the particle distribution functions: particles (and ions at a faster rate) tend to thermalise to the background. To pinpoint the consequences of this, we compare reconnection simulations with and without background. References [1] E E Lawrence et al. Physical review letters, 110(1):015001, 2013. [2] S Markidis et al. Mathematics and Computers in Simulation, 80(7):1509-1519, 2010. [3] K Nanbu. IEEE Transactions on plasma science, 28(3):971-990, 2000.

  1. Medical response to effects of ionising radiation. [Nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    Crosbie, W.A.; Gittus, J.H. (UKAEA Headquarters, London (UK))

    1989-01-01

    The proceedings of a conference on 'Medical Response to Effects of Ionising Radiation' in 1989 in the form of nineteen papers published as a book. Topics discussed include radiation accidents at nuclear facilities, the medical management of radiation casualties, the responsibilities, plans and resources for coping with a nuclear accident and finally the long term effects of radiation, including leukaemia epidemiology studies. All papers were selected and indexed separately. (UK).

  2. IEC standards for individual monitoring of ionising radiation.

    Science.gov (United States)

    Voytchev, M; Ambrosi, P; Behrens, R; Chiaro, P

    2011-03-01

    This paper presents IEC/SC 45B 'Radiation protection instrumentation' and its standards for individual monitoring of ionising radiation: IEC 61526 Ed. 3 for active personal dosemeters and IEC 62387-1 for passive integrating dosimetry systems. The transposition of these standards as CENELEC (European) standards is also discussed together with the collaboration between IEC/SC 45B and ISO/TC 85/SC 2.

  3. Ionising radiation metrology for the metallurgical industry

    Directory of Open Access Journals (Sweden)

    García-Toraño E.

    2014-01-01

    Full Text Available Every year millions tons of steel are produced worldwide from recycled scrap loads. Although the detection systems in the steelworks prevent most orphan radioactive sources from entering the furnace, there is still the possibility of accidentally melting a radioactive source. The MetroMetal project, carried out in the frame of the European Metrology Research Programme (EMRP, addresses this problem by studying the existing measurement systems, developing sets of reference sources in various matrices (cast steel, slag, fume dust and proposing new detection instruments. This paper presents the key lines of the project and describes the preparation of radioactive sources as well as the intercomparison exercises used to test the calibration and correction methods proposed within the project.

  4. Electrospray ionisation mass spectrometry: principles and clinical applications.

    Science.gov (United States)

    Ho, C S; Lam, C W K; Chan, M H M; Cheung, R C K; Law, L K; Lit, L C W; Ng, K F; Suen, M W M; Tai, H L

    2003-01-01

    This mini-review provides a general understanding of electrospray ionisation mass spectrometry (ESI-MS) which has become an increasingly important technique in the clinical laboratory for structural study or quantitative measurement of metabolites in a complex biological sample. The first part of the review explains the electrospray ionisation process, design of mass spectrometers with separation capability, characteristics of the mass spectrum, and practical considerations in quantitative analysis. The second part then focuses on some clinical applications. The capability of ESI-tandem-MS in measuring bio-molecules sharing similar molecular structures makes it particularly useful in screening for inborn errors of amino acid, fatty acid, purine, pyrimidine metabolism and diagnosis of galactosaemia and peroxisomal disorders. Electrospray ionisation is also efficient in generating cluster ions for structural elucidation of macromolecules. This has fostered a new and improved approach (vs electrophoresis) for identification and quantification of haemoglobin variants. With the understanding of glycohaemoglobin structure, an IFCC reference method for glycohaemoglobin assay has been established using ESI-MS. It represents a significant advancement for the standardisation of HbA1c in diabetic monitoring. With its other applications such as in therapeutic drug monitoring, ESI-MS will continue to exert an important influence in the future development and organisation of the clinical laboratory service.

  5. Erich Regener and the maximum in ionisation of the atmosphere

    CERN Document Server

    Carlson, P

    2014-01-01

    In the 1930s the German physicist Erich Regener (1881-1955) did important work on the measurement of the rate of production of ionisation deep under-water and in the atmosphere. He discovered, along with one of his students, Georg Pfotzer, the altitude at which the production of ionisation in the atmosphere reaches a maximum, often, but misleadingly, called the Pfotzer maximum. Regener was one of the first to estimate the energy density of cosmic rays, an estimate that was used by Baade and Zwicky to bolster their postulate that supernovae might be their source. Yet Regener's name is less recognised by present-day cosmic ray physicists than it should be largely because in 1937 he was forced to take early retirement by the National Socialists as his wife had Jewish ancestors. In this paper we briefly review his work on cosmic rays and recommend an alternative naming of the ionisation maximum. The influence that Regener had on the field through his son, his son-in-law, his grandsons and his students and through...

  6. Atmospheric pressure chemical ionisation liquid chromatography/mass spectrometry of bacteriochlorophylls from Chlorobiaceae: characteristic fragmentations.

    Science.gov (United States)

    Airs, Ruth L; Keely, Brendan J

    2002-01-01

    Atmospheric pressure chemical ionisation liquid chromatography/mass spectrometry/mass spectrometry (APCI-LC/MS/MS) has been applied to the study of bacteriochlorophylls c, d, and e of phototrophic prokaryotes. Cultures of Chlorobiaceae containing bacteriochlorophyll c, d or e were examined using a high-resolution high-performance liquid chromatography (HPLC) method and APCI-LC/MS/MS employing post-column addition of formic acid. The results reveal complex distributions of bacteriochlorophyll homologues, with some closely eluting species giving isobaric protonated molecules. On-line LC/MS/MS studies reveal characteristic fragment ions for bacteriochlorophylls c, d, and e. Fragmentations involving loss of the extended alkyl substituents that are unique to bacteriochlorophylls c, d and e and their derivatives have been rationalised by studying the phaeophorbides and the results applied to the direct study of the bacteriochlorophylls.

  7. Boron - A potential goiterogen?

    Science.gov (United States)

    Popova, Elizaveta V; Tinkov, Alexey A; Ajsuvakova, Olga P; Skalnaya, Margarita G; Skalny, Anatoly V

    2017-07-01

    The iodine deficiency disorders (IDD) include a variety of disturbances such as decreased fertility, increased perinatal and infant mortality, impaired physical and intellectual development, mental retardation, cretinism, hypothyroidism, and endemic goiter (EG). The occurrence of the latter is determined by interplay between genetic and environmental factors. The major environmental factor is iodine status that is required for normal thyroid hormone synthesis. However, other factors like intake of micronutrients and goiterogens also have a significant impact. Essential and toxic trace elements both play a significant role in thyroid physiology. We hypothesize that in terms of overexposure boron may serve as a potential goiterogen. In particular, it is proposed that boron overload may impair thyroid physiology ultimately leading to goiter formation. Certain studies provide evidential support of the hypothesis. In particular, it has been demonstrated that serum and urinary B levels are characterized by a negative association with thyroid hormone levels in exposed subjects. Single indications on the potential efficiency of B in hypothyroidism also exist. Moreover, the levels of B were found to be interrelated with thyroid volume in children environmentally exposed to boron. Experimental studies also demonstrated a significant impact of boron on thyroid structure and hormone levels. Finally, the high rate of B cumulation in thyroid may also indicate that thyroid is the target for B activity. Chemical properties of iodine and boron also provide a background for certain competition. However, it is questionable whether these interactions may occur in the biological systems. Further clinical and experimental studies are required to support the hypothesis of the involvement of boron overexposure in goiter formation. If such association will be confirmed and the potential mechanisms elucidated, it will help to regulate the incidence of hypothyroidism and goiter in endemic

  8. Boronated liposome development and evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Hawthorne, M.F. [Univ. of California, Los Angeles, CA (United States)

    1995-11-01

    The boronated liposome development and evaluation effort consists of two separate tasks. The first is the development of new boron compounds and the synthesis of known boron species with BNCT potential. These compounds are then encapsulated within liposomes for the second task, biodistribution testing in tumor-bearing mice, which examines the potential for the liposomes and their contents to concentrate boron in cancerous tissues.

  9. Semiclassical calculation of ionisation rate for Rydberg helium atoms in an electric field

    Institute of Scientific and Technical Information of China (English)

    Wang De-Hua

    2011-01-01

    The ionisation of Rydberg helium atoms in an electric field above the classical ionisation threshold has been examined using the semiclassical method, with particular emphasis on discussing the influence of the core scattering on the escape dynamics of electrons. The results show that the Rydberg helium atoms ionise by emitting a train of electron pulses. Unlike the case of the ionisation of Rydberg hydrogen atom in parallel electric and magnetic fields,where the pulses of the electron are caused by the external magnetic field, the pulse trains for Rydberg helium atoms are created through core scattering. Each peak in the ionisation rate corresponds to the contribution of one core-scattered combination trajectory. This fact further illustrates that the ionic core scattering leads to the chaotic property of the Rydberg helium atom in external fields. Our studies provide a simple explanation for the escape dynamics in the ionisation of nonhydrogenic atoms in external fields.

  10. In Vivo Boron Uptake Determination for Boron Neutron Capture Synovectomy

    Energy Technology Data Exchange (ETDEWEB)

    Binello, Emanuela; Shortkroff, Sonya; Yanch, Jacquelyn C.

    1999-06-06

    Boron neutron capture synovectomy (BNCS) has been proposed as a new application of the boron neutron capture reaction for the treatment of rheumatoid arthritis. In BNCS, a boron compound is injected into the joint space, where it is taken up by the synovium. The joint is then irradiated with neutrons of a desired energy range, inducing the boron neutron capture reaction in boron-loaded cells. Boron uptake by the synovium is an important parameter in the assessment of the potential of BNCS and in the determination of whether to proceed to animal irradiations for the testing of therapeutic efficacy. We present results from an investigation of boron uptake in vivo by the synovium.

  11. Effect of Boronization on Ohmic Plasmas in NSTX

    Energy Technology Data Exchange (ETDEWEB)

    Skinner, C.H.; Kugel, H.; Maingi, R.; Wampler, W.R.; Blanchard, W.; Bell, M.; Bell, R.; LeBlanc, B.; Gates, D.; Kaye, S.; LaMarche, P.; Menard, J.; Mueller, D.; Na, H.K.; Nishino, N.; Paul, S.; Sabbagh, S.; Soukhanovskii, V.

    2001-03-27

    Boronization of the National Spherical Torus Experiment (NSTX) has enabled access to higher density, higher confinement plasmas. A glow discharge with 4 mTorr helium and 10% deuterated trimethyl boron deposited 1.7 g of boron on the plasma facing surfaces. Ion beam analysis of witness coupons showed a B+C areal density of 10 to the 18 (B+C) cm to the -2 corresponding to a film thickness of 100 nm. Subsequent ohmic discharges showed oxygen emission lines reduced by x15, carbon emission reduced by two and copper reduced to undetectable levels. After boronization, the plasma current flattop time increased by 70% enabling access to higher density, higher confinement plasmas.

  12. Trefoil factor 3 (TFF3) enhances the oncogenic characteristics of prostate carcinoma cells and reduces sensitivity to ionising radiation.

    Science.gov (United States)

    Perera, Omesha; Evans, Angharad; Pertziger, Mikhail; MacDonald, Christa; Chen, Helen; Liu, Dong-Xu; Lobie, Peter E; Perry, Jo K

    2015-05-28

    Trefoil factor 3 (TFF3) is a secreted protein which functions in mucosal repair of the gastrointestinal tract. This is achieved through the combined stimulation of cell migration and prevention of apoptosis and anoikis, thus facilitating repair. Deregulated TFF3 expression at the gene and protein level is implicated in numerous cancers. In prostate cancer TFF3 has previously been reported as a potential biomarker, overexpressed in a subset of primary and metastatic cases. Here we investigated the effect of increased TFF3 expression on prostate cancer cell behaviour. Oncomine analysis demonstrated that TFF3 mRNA expression was upregulated in prostate cancer compared to normal tissue. Forced-expression models were established in the prostate cancer cell lines, DU145 and PC3, by stable transfection of an expression vector containing the TFF3 cDNA. Forced expression of TFF3 significantly increased total cell number and cell viability, cell proliferation and cell survival. In addition, TFF3 enhanced anchorage independent growth, 3-dimensional colony formation, wound healing and cell migration compared to control transfected cell lines. We also observed reduced sensitivity to ionising radiation in stably transfected cell lines. In dose response experiments, forced expression of TFF3 significantly enhanced the regrowth of PC3 cells following ionising radiation compared with control transfected cells. In addition, TFF3 enhanced clonogenic survival of DU145 and PC3 cells. These studies indicate that targeting TFF3 for the treatment of prostate cancer warrants further investigation.

  13. Intercomparison of ionisation chamber measurements from (125)I seeds.

    Science.gov (United States)

    Davies, J B; Enari, K F; Baldock, C

    2007-05-01

    The reference air kerma rates of a set of individual (125)I seeds were calculated from current measurements of a calibrated re-entrant ionisation chamber. Single seeds were distributed to seven Australian brachytherapy centres for the same measurement with the user's instrumentation. Results are expressed as the ratio of the reference air kerma rate measured by the Australian Nuclear Science & Technology Organisation (ANSTO) to the reference air kerma rate measured at the centre. The intercomparison ratios of all participants were within +/-5% of unity.

  14. Ionisation constants of inorganic acids and bases in aqueous solution

    CERN Document Server

    Perrin, D D

    2013-01-01

    Ionisation Constants of Inorganic Acids and Bases in Aqueous Solution, Second Edition provides a compilation of tables that summarize relevant data recorded in the literature up to the end of 1980 for the ionization constants of inorganic acids and bases in aqueous solution. This book includes references to acidity functions for strong acids and bases, as well as details about the formation of polynuclear species. This text then explains the details of each column of the tables, wherein column 1 gives the name of the substance and the negative logarithm of the ionization constant and column 2

  15. Lattice dynamics of {alpha} boron and of boron carbide; Proprietes vibrationnelles du bore {alpha} et du carbure de bore

    Energy Technology Data Exchange (ETDEWEB)

    Vast, N

    1999-07-01

    The atomic structure and the lattice dynamics of {alpha} boron and of B{sub 4}C boron carbide have been studied by Density Functional Theory (D.F.T.) and Density Functional Perturbation Theory (D.F.P.T.). The bulk moduli of the unit-cell and of the icosahedron have been investigated, and the equation of state at zero temperature has been determined. In {alpha} boron, Raman diffusion and infrared absorption have been studied under pressure, and the theoretical and experimental Grueneisen coefficients have been compared. In boron carbide, inspection of the theoretical and experimental vibrational spectra has led to the determination of the atomic structure of B{sub 4}C. Finally, the effects of isotopic disorder have been modeled by an exact method beyond the mean-field approximation, and the effects onto the Raman lines has been investigated. The method has been applied to isotopic alloys of diamond and germanium. (author)

  16. Plasma boron and the effects of boron supplementation in males.

    Science.gov (United States)

    Green, N R; Ferrando, A A

    1994-11-01

    Recently, a proliferation of athletic supplements has been marketed touting boron as an ergogenic aid capable of increasing testosterone. The effect of boron supplementation was investigated in male bodybuilders. Ten male bodybuilders (aged 20 to 26) were given a 2.5-mg boron supplement, while nine male bodybuilders (aged 21 to 27) were given a placebo for 7 weeks. Plasma total and free testosterone, plasma boron, lean body mass, and strength measurements were determined on day 1 and day 49 of the study. A microwave digestion procedure followed by inductively coupled argon plasma spectroscopy was used for boron determination. Twelve subjects had boron values at or above the detection limit with median value of 25 ng/ml (16 ng/ml lower quartile and 33 ng/ml upper quartile). Of the ten subjects receiving boron supplements, six had an increase in their plasma boron. Analysis of variance indicated no significant effect of boron supplementation on any of the other dependent variables. Both groups demonstrated significant increases in total testosterone (p bodybuilding can increase total testosterone, lean body mass, and strength in lesser-trained bodybuilders, but boron supplementation affects these variables not at all.

  17. Boron contamination in drinking - irrigation water and boron removal methods

    Directory of Open Access Journals (Sweden)

    Meltem Bilici Başkan

    2014-03-01

    Full Text Available Boron presents in IIIA group of periodic table and has high ionization capacity. Therefore it is classified as a metalloid. Average boron concentration in earth's crust is 10 mg/kg. It presents in the environment as a salts of Ca, Na, and Mg. Boron reserves having high concentration and economical extent are found mostly in Turkey and in arid, volcanic and high hydrothermal activity regions of U.S. as compounds of boron attached to oxygen. Boron is an essential micronutrient for plants, although it may be toxic at higher levels. The range in which it is converted from a nutrient to a contaminant is quite narrow. Boron presents in water environment as a boric acid and rarely borate salts. The main boron sources, whose presence is detected in surface waters, are urban wastes and industrial wastes, which can come from a wide range of different activities as well as several chemical products used in agriculture. In Turkey, the most pollutant toxic element in drinking and irrigation water is boron. Therefore boron removal is very important in terms of human health and agricultural products in high quality. Mainly boron removal methods from drinking water and irrigation water are ion exchange, ultrafiltration, reverse osmosis, and adsorption.

  18. BCM6: New Generation of Boron Meter

    Energy Technology Data Exchange (ETDEWEB)

    Pirat, P. [Rolls-Royce Civil Nuclear SAS (France)

    2010-07-01

    Full text of publication follows: Rolls-Royce has developed a new generation of boron meter, based on more than 30 years of experience. The Rolls-Royce BCM6 boron meter provides Nuclear Power Plant (NPP) operators with the boron concentration of the primary circuit. The meter provides continuous and safe measurements with no manual sampling and no human contact. In this paper, technical features, advantages and customer benefits of the use of the new generation of Rolls-Royce BCM6 boron meter will be detailed. Values and associated alarms are provides over different media: 4-20 mA outputs, relays, displays in the main control room and in the chemical lab, and digital links. A special alarm avoids unexpected homogeneous dilution of the primary circuit, which is a critical operational parameter. The Rolls-Royce BCM6 boron meter is fully configurable over a set of parameters allowing adaptation to customer needs. It has a differential capability, thus eliminating neutronic noise and keeping measurements accurate, even in the case of fuel clad rupture. Measurements are accurate, reliable, and have a quick response time. Equipment meets state-of-the-art qualification requests. Designed in 2008, the BCM6 boron meter is the newest equipment of Rolls-Royce boron meters product line. It has been chosen to equip the French EPR NPP and complies with the state-of-the-art of the technology. Rolls-Royce has more than 30 years of experience in Instrumentation and Controls with more than 75 NPP units operating worldwide. All of this experience return has been put in this new generation of equipment to provide the customer with the best operation. About Rolls-Royce Rolls-Royce is a global business providing integrated power systems for use on land, at sea and in the air. The Group has a balanced business portfolio with leading market positions. Rolls-Royce has a broad range of civil nuclear expertise, including work related to licensing and safety reviews, engineering design

  19. Methods of producing continuous boron carbide fibers

    Energy Technology Data Exchange (ETDEWEB)

    Garnier, John E.; Griffith, George W.

    2015-12-01

    Methods of producing continuous boron carbide fibers. The method comprises reacting a continuous carbon fiber material and a boron oxide gas within a temperature range of from approximately 1400.degree. C. to approximately 2200.degree. C. Continuous boron carbide fibers, continuous fibers comprising boron carbide, and articles including at least a boron carbide coating are also disclosed.

  20. Bright prospects for boron

    NARCIS (Netherlands)

    Wassink, J.

    2012-01-01

    Professor Lis Nanver at Dimes has laid the foundation for a range of new photodetectors by creating a thin coating of boron on a silicon substrate. The sensors are used in ASML’s latest lithography machines and FEI’s most sensitive electron microscopes.

  1. Bright prospects for boron

    NARCIS (Netherlands)

    Wassink, J.

    2012-01-01

    Professor Lis Nanver at Dimes has laid the foundation for a range of new photodetectors by creating a thin coating of boron on a silicon substrate. The sensors are used in ASML’s latest lithography machines and FEI’s most sensitive electron microscopes.

  2. Nothing Boring About Boron.

    Science.gov (United States)

    Pizzorno, Lara

    2015-08-01

    The trace mineral boron is a micronutrient with diverse and vitally important roles in metabolism that render it necessary for plant, animal, and human health, and as recent research suggests, possibly for the evolution of life on Earth. As the current article shows, boron has been proven to be an important trace mineral because it (1) is essential for the growth and maintenance of bone; (2) greatly improves wound healing; (3) beneficially impacts the body's use of estrogen, testosterone, and vitamin D; (4) boosts magnesium absorption; (5) reduces levels of inflammatory biomarkers, such as high-sensitivity C-reactive protein (hs-CRP) and tumor necrosis factor α (TNF-α); (6) raises levels of antioxidant enzymes, such as superoxide dismutase (SOD), catalase, and glutathione peroxidase; (7) protects against pesticide-induced oxidative stress and heavy-metal toxicity; (8) improves the brains electrical activity, cognitive performance, and short-term memory for elders; (9) influences the formation and activity of key biomolecules, such as S-adenosyl methionine (SAM-e) and nicotinamide adenine dinucleotide (NAD(+)); (10) has demonstrated preventive and therapeutic effects in a number of cancers, such as prostate, cervical, and lung cancers, and multiple and non-Hodgkin's lymphoma; and (11) may help ameliorate the adverse effects of traditional chemotherapeutic agents. In none of the numerous studies conducted to date, however, do boron's beneficial effects appear at intakes > 3 mg/d. No estimated average requirements (EARs) or dietary reference intakes (DRIs) have been set for boron-only an upper intake level (UL) of 20 mg/d for individuals aged ≥ 18 y. The absence of studies showing harm in conjunction with the substantial number of articles showing benefits support the consideration of boron supplementation of 3 mg/d for any individual who is consuming a diet lacking in fruits and vegetables or who is at risk for or has osteopenia; osteoporosis; osteoarthritis (OA

  3. Characterisation of bacteria by matrix-assisted laser desorption/ionisation and electrospray mass spectrometry

    NARCIS (Netherlands)

    Baar, B.L.M. van

    2000-01-01

    Chemical analysis for the characterisation of micro-organisms is rapidly evolving, after the recent advent of new ionisation methods in mass spectrometry (MS): electrospray (ES) and matrix-assisted laser desorption/ionisation (MALDI). These methods allow quick characterisation of micro-organisms, ei

  4. Controlling ionisation and fragmentation processes in CO2 via inelastic electron recollisions

    Directory of Open Access Journals (Sweden)

    Frasinski L. J.

    2013-03-01

    Full Text Available The angular dependence of nonsequential double ionisation and dissociation induced by laser driven inelastic electron rescattering was investigated experimentally in aligned CO2. A clear dependence on the recollision angle was found demonstrating quantum control of ionisation and dissociation processes in the strong field regime.

  5. Boron-10 ABUNCL Models of Fuel Testing

    Energy Technology Data Exchange (ETDEWEB)

    Siciliano, Edward R.; Lintereur, Azaree T.; Kouzes, Richard T.; Ely, James H.

    2013-10-01

    The Department of Energy Office of Nuclear Safeguards and Security (NA-241) is supporting the project Coincidence Counting With Boron-Based Alternative Neutron Detection Technology at Pacific Northwest National Laboratory (PNNL) for the development of a 3He proportional counter alternative neutron coincidence counter. The goal of this project is to design, build and demonstrate a system based upon 10B-lined proportional tubes in a configuration typical for 3He-based coincidence counter applications. This report provides results from MCNP simulations of the General Electric Reuter-Stokes Alternative Boron-Based Uranium Neutron Coincidence Collar (ABUNCL) active configuration model with fuel pins previously measured at Los Alamos National Laboratory. A comparison of the GE-ABUNCL simulations and simulations of 3He based UNCL-II active counter (the system for which the GE-ABUNCL was targeted to replace) with the same fuel pin assemblies is also provided.

  6. Oxidation of Silicon and Boron in Boron Containing Molten Iron

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A new process of directly smelting boron steel from boron-containing pig iron has been established. The starting material boron-containing pig iron was obtained from ludwigite ore, which is very abundant in the eastern area of Liaoning Province of China. The experiment was performed in a medium-frequency induction furnace, and Fe2O3 powder was used as the oxidizing agent. The effects of temperature, addition of Fe2O3, basicity, stirring, and composition of melt on the oxidation of silicon and boron were investigated respectively. The results showed that silicon and boron were oxidized simultaneously and their oxidation ratio exceeded 90% at 1 400 ℃. The favorable oxidation temperature of silicon was about 1 300-1 350 C. High oxygen potential of slag and strong stirring enhanced the oxidation of silicon and boron.

  7. Transferring calibration coefficients from ionisation chambers used for diagnostic radiology to transmission chambers.

    Science.gov (United States)

    Yoshizumi, Maíra T; Caldas, Linda V E

    2012-07-01

    In this work, the response of a double volume transmission ionisation chamber, developed at the Instituto de Pesquisas Energéticas e Nucleares, was compared to that of a commercial transmission chamber. Both ionisation chambers were tested in different X-ray beam qualities using secondary standard ionisation chambers as reference dosimeters. These standard ionisation chambers were a parallel-plate and a cylindrical ionisation chambers, used for diagnostic radiology and mammography beam qualities, respectively. The response of both transmission chambers was compared to that of the secondary standard chambers to obtain coefficients of equivalence. These coefficients allow the transmission chambers to be used as reference equipment. Copyright © 2011 Elsevier Ltd. All rights reserved.

  8. Lattice vibrations of icosahedral boron-rich solids

    Energy Technology Data Exchange (ETDEWEB)

    Beckel, C.L.; Yousaf, M. (The University of New Mexico, Albuquerque, New Mexico 87131 (United States))

    1991-07-01

    The rhombohedral lattices for {alpha}-boron, boron arsenide, and boron phosphide are each of D{sub 3d} symmetry and have bases that include B{sub 12} icosahedra. Boron carbide with B{sub 4}C stoichiometry has near-D{sub 3d} symmetry and is almost certainly composed of B{sub 11}C icosahedra and C-B-C chains. Comparable classical force field models are applied to each of these crystals to correlate q=0 phonon structure with experimental Raman and IR spectra. We here describe our methods and contrast interaction strengths for different materials. Vibrations are correlated in the different crystals through normal mode eigenvector expansions. Acoustic wave velocities from Brillouin zone dispersion curves in two distinct symmetry-axis directions are presented and contrasted for {alpha}-boron and B{sub 12}As{sub 2}. The origin of lines with anomalous polarization and width in {alpha}-boron, B{sub 12}As{sub 2}, and B{sub 12}P{sub 2} is considered.

  9. Structures, stability, mechanical and electronic properties of α-boron and α*-boron

    OpenAIRE

    Chaoyu He; J. X. Zhong

    2013-01-01

    The structures, stability, mechanical and electronic properties of α-boron and a promising metastable boron phase (α*-boron) have been studied by first-principles calculations. α-boron and α*-boron consist of equivalent icosahedra B12 clusters in different connecting configurations of “3S-6D-3S” and “2S-6D-4S”, respectively. The total energy calculations show that α*-boron is less stable than α-boron but more favorable than the well-known β-boron and γ-boron at zero pressure. Both α-boron and...

  10. Fivefold twinned boron carbide nanowires.

    Science.gov (United States)

    Fu, Xin; Jiang, Jun; Liu, Chao; Yuan, Jun

    2009-09-01

    Chemical composition and crystal structure of fivefold twinned boron carbide nanowires have been determined by electron energy-loss spectroscopy and electron diffraction. The fivefold cyclic twinning relationship is confirmed by systematic axial rotation electron diffraction. Detailed chemical analysis reveals a carbon-rich boron carbide phase. Such boron carbide nanowires are potentially interesting because of their intrinsic hardness and high temperature thermoelectric property. Together with other boron-rich compounds, they may form a set of multiply twinned nanowire systems where the misfit strain could be continuously tuned to influence their mechanical properties.

  11. Viscous Kelvin-Helmholtz instabilities in highly ionised plasmas

    CERN Document Server

    Roediger, E; Nulsen, P; Churazov, E; Forman, W; Brueggen, M; Kokotanekova, R

    2013-01-01

    Transport coefficients in highly ionised plasmas like the intra-cluster medium (ICM) are still ill-constrained. They influence various processes, among them the mixing at shear flow interfaces due to the Kelvin-Helmholtz instability (KHI). The observed structure of potential mixing layers can be used to infer the transport coefficients, but the data interpretation requires a detailed knowledge of the long-term evolution of the KHI under different conditions. Here we present the first systematic numerical study of the effect of constant and temperature-dependent isotropic viscosity over the full range of possible values. We show that moderate viscosities slow down the growth of the KHI and reduce the height of the KHI rolls and their rolling-up. Viscosities above a critical value suppress the KHI. The effect can be quantified in terms of the Reynolds number Re = U{\\lambda}/{\

  12. RF System for the MICE Demonstration of Ionisation Cooling

    Energy Technology Data Exchange (ETDEWEB)

    Ronald, K.; et al.

    2017-04-01

    Muon accelerators offer an attractive option for a range of future particle physics experiments. They can enable high energy (TeV+) high energy lepton colliders whilst mitigating the difficulty of synchrotron losses, and can provide intense beams of neutrinos for fundamental physics experiments investigating the physics of flavor. The method of production of muon beams results in high beam emittance which must be reduced for efficient acceleration. Conventional emittance control schemes take too long, given the very short (2.2 microsecond) rest lifetime of the muon. Ionisation cooling offers a much faster approach to reducing particle emittance, and the international MICE collaboration aims to demonstrate this technique for the first time. This paper will present the MICE RF system and its role in the context of the overall experiment.

  13. Fragmentation dynamics of ammonia cluster ions after single photon ionisation

    Energy Technology Data Exchange (ETDEWEB)

    Kaiser, E.; Vries, J. de; Steger, H.; Menzel, C.; Kamke, W.; Hertel, I.V. (Freiburg Univ. (Germany, F.R.). Fakultaet fuer Physik Freiburg Univ. (Germany, F.R.). Freiburger Materialforschungszentrum)

    1991-01-01

    A reflecting time of flight mass spectrometer (RETOF) is used to study unimolecular and collision induced fragmentation of ammonia cluster ions. Synchrotron radiation from the BESSY electron storage ring is used in a range of photon energies from 9.08 up to 17.7 eV for single photon ionisation of neutral clusters in a supersonic beam. The threshold photoelectron photoion coincidence technique (TPEPICO) is used to define the energy initially deposited into the cluster ions. Metastable unimolecular decay ({mu}s range) is studied using the RETOF's capacity for energy analysis. Under collision free conditions the by far most prominent metastable process is the evaporation of one neutral NH{sub 3} monomer from protonated clusters (NH{sub 3}){sub x}NH{sub 4}{sup +}. Abundance of homogeneous vs. protonated cluster ions and of metastable fragments are reported as a function of photon energy and cluster size up to n=10. (orig.).

  14. Studies of Non-Targeted Effects of Ionising Radiation

    Energy Technology Data Exchange (ETDEWEB)

    Oleg V Belyakov; Heli Mononen; Marjo Peraelae [STUK - Radiation and Nuclear Safety Authority, Helsinki (Finland)

    2006-07-01

    The discovery of ionising radiation induced non-targeted effects is important for understanding the dose-response mechanisms relevant to low dose irradiation in vivo. One important question is whether the non-targeted effects relates to a protective mechanism or whether, conversely, it amplifies the number of cells damaged by the isolated radiation tracks of low dose exposures leading to an increased risk of carcinogenesis. One theory supported by the experimental data obtained during this project is that the main functions of the non-targeted effects are to decrease the risk of transformation in a multicellular organism exposed to radiation. Differences in the gene expression profiles, temporal and spatial patterns of key proteins expressed in directly irradiated and bystander cells may determine how the cells ultimately respond to low doses of radiation. Such a mechanism of co-operative response would make the tissue system much more robust. (N.C.)

  15. Predictive value of derived calcium figures based on the measurement of ionised calcium.

    Science.gov (United States)

    Gardner, M D; Dryburgh, F J; Fyffe, J A; Jenkins, A S

    1981-03-01

    The algorithms used in this hospital to assess calcium status are calculated ionised serum calcium and the serum calcium concentration adjusted for albumin. In order to establish their clinical usefulness, they were compared with the ionised calcium concentration measured on the Nova 2 instrument in patients with various calcium and protein abnormalities. Good correlation was found between the measured and calculated values. The predictive values for the calculated results and for total serum calcium concentrations are presented. In this series, the derived values were useful in predicting the serum ionised calcium concentration of the patients studied.

  16. Double Ionisation in R-Matrix Theory Using a 2-electron Outer Region

    CERN Document Server

    Wragg, Jack; van der Hart, H W

    2015-01-01

    We have developed a two-electron outer region for use within R-matrix theory to describe double ionisation processes. The capability of this method is demonstrated for single-photon double ionisation of He in the photon energy region between 80 eV to 180 eV. The cross sections are in agreement with established data. The extended RMT method also provides information on higher-order processes, as demonstrated by the identification of signatures for sequential double ionisation processes involving an intermediate He$^{+}$ state with $n=2$.

  17. Differential ionisation of natural antioxidant polyenes in electrospray and nanospray mass spectrometry.

    Science.gov (United States)

    Guaratini, Thais; Gates, Paul J; Pinto, Ernani; Colepicolo, Pio; Lopes, Norberto P

    2007-01-01

    Carotenoids are natural products with high economic relevance for the pharmaceutical industries and are a common subject for biochemical research. Reported here is a comparative study of the ionisation of carotenoids by electrospray mass spectrometry (ESI-MS) and nanospray mass spectrometry (nanoESI-MS). The results demonstrate that, along with solvent choice, the influence of the different ionisation processes of ESI and nanoESI are fundamental in determining how ionisation is achieved and which ions (molecular ion or protonated molecule) are observed in MS. The increased understanding afforded by this study will help in the development of unequivocal microanalytical methods for carotenoids and related antioxidant polyenes.

  18. A theranostic approach based on the use of a dual boron/Gd agent to improve the efficacy of Boron Neutron Capture Therapy in the lung cancer treatment.

    Science.gov (United States)

    Alberti, Diego; Protti, Nicoletta; Toppino, Antonio; Deagostino, Annamaria; Lanzardo, Stefania; Bortolussi, Silva; Altieri, Saverio; Voena, Claudia; Chiarle, Roberto; Geninatti Crich, Simonetta; Aime, Silvio

    2015-04-01

    This study aims at developing an innovative theranostic approach for lung tumor and metastases treatment, based on Boron Neutron Capture Therapy (BNCT). It relies on to the use of low density lipoproteins (LDL) as carriers able to maximize the selective uptake of boron atoms in tumor cells and, at the same time, to quantify the in vivo boron distribution by magnetic resonance imaging (MRI). Tumor cells uptake was initially assessed by ICP-MS and MRI on four types of tumor (TUBO, B16-F10, MCF-7, A549) and one healthy (N-MUG) cell lines. Lung metastases were generated by intravenous injection of a Her2+ breast cancer cell line (i.e. TUBO) in BALB/c mice and transgenic EML4-ALK mice were used as primary tumor model. After neutron irradiation, tumor growth was followed for 30-40 days by MRI. Tumor masses of boron treated mice increased markedly slowly than the control group. From the clinical editor: In this article, the authors described an improvement to existing boron neutron capture therapy. The dual MRI/BNCT agent, carried by LDLs, was able to maximize the selective uptake of boron in tumor cells, and, at the same time, quantify boron distribution in tumor and in other tissues using MRI. Subsequent in vitro and in vivo experiments showed tumor cell killing after neutron irradiation. Copyright © 2015 Elsevier Inc. All rights reserved.

  19. Boron isotopic compositions of some boron minerals

    Energy Technology Data Exchange (ETDEWEB)

    Oi, Takao; Musashi, Masaaki; Ossaka, Tomoko; Kakihana, Hidetake (Sophia Univ., Tokyo (Japan)); Nomura, Masao; Okamoto, Makoto (Tokyo Institute of Technology (Japan))

    1989-12-01

    Boron minerals that have different structural formulae but are supposed to have the same geologic origin have been collected and analyzed for the {sup 11}B/{sup 10}B isotopic ratio. It has been reconfirmed that minerals of marine origin have higher {sup 11}B/{sup 10}B ratios than those of nonmarine origin. It has been found that the sequence of decreasing {sup 11}B/{sup 10}B values among the minerals with the same geologic origin is; borax, tincal, kernite (Na borates) > ulexite (Na/Ca borate) > colemanite, iyoite, meyerhofferite (Ca borates). This sequence is explainable on the basis of the difference in crystal structure among the minerals. That is, minerals with high BO{sub 3}/BO{sub 4} ratios, (the ratio of the number of the BO{sub 3} triangle units to the number of the BO{sub 4} tetrahedron units in the structural formula of a mineral) have higher {sup 11}B/{sup 10}B ratios.

  20. Boron supplementation in broiler diets

    Directory of Open Access Journals (Sweden)

    EJ Fassani

    2004-12-01

    Full Text Available Boron supplementation in broiler feed is not a routine practice. However, some reports suggest a positive effect of boron on performance. This study assessed the effects of boron supplementation on broiler performance. Diets were based on maize and soybean meal, using boric acid P.A. as boron source. Six supplementation levels (0, 30, 60, 90, 120 and 150 ppm were evaluated using 1,440 one-day old males housed at a density of 30 chickens in each of 48 experimental plots of 3m². A completely randomized block design was used with 8 replicates. Feed intake, weight gain and feed conversion were assessed in the periods from 1 to 7 days, 1 to 21 days and 1 to 42 days of age, and viability was evaluated for the total 42-day rearing period. No performance variable was affected by boron supplementation (p>0.05 in the period from 1 to 7 days. The regression analysis indicated an ideal level of 37.4 ppm of boron for weight gain from 1 to 21 days (p0.05, although feed intake was reduced linearly with increased boron levels (p0.05. Ash and calcium percentages in the tibias of broilers and viability in the total rearing period were not affected by boron supplementation (p>0.05.

  1. Introduction to Neutron Coincidence Counter Design Based on Boron-10

    Energy Technology Data Exchange (ETDEWEB)

    Kouzes, Richard T.; Ely, James H.; Lintereur, Azaree T.; Siciliano, Edward R.

    2012-01-22

    The Department of Energy Office of Nonproliferation Policy (NA-241) is supporting the project 'Coincidence Counting With Boron-Based Alternative Neutron Detection Technology' at Pacific Northwest National Laboratory (PNNL) for development of an alternative neutron coincidence counter. The goal of this project is ultimately to design, build and demonstrate a boron-lined proportional tube based alternative system in the configuration of a coincidence counter. This report, providing background information for this project, is the deliverable under Task 1 of the project.

  2. Functionalized boron nitride nanotubes

    Science.gov (United States)

    Sainsbury, Toby; Ikuno, Takashi; Zettl, Alexander K

    2014-04-22

    A plasma treatment has been used to modify the surface of BNNTs. In one example, the surface of the BNNT has been modified using ammonia plasma to include amine functional groups. Amine functionalization allows BNNTs to be soluble in chloroform, which had not been possible previously. Further functionalization of amine-functionalized BNNTs with thiol-terminated organic molecules has also been demonstrated. Gold nanoparticles have been self-assembled at the surface of both amine- and thiol-functionalized boron nitride Nanotubes (BNNTs) in solution. This approach constitutes a basis for the preparation of highly functionalized BNNTs and for their utilization as nanoscale templates for assembly and integration with other nanoscale materials.

  3. Medical exposure to ionising radiation and the risk of brain tumours

    DEFF Research Database (Denmark)

    Blettner, Maria; Schlehofer, Brigitte; Samkange-Zeeb, Florence

    2007-01-01

    BACKGROUND: The role of exposure to low doses of ionising radiation in the aetiology of brain tumours has yet to be clarified. The objective of this study was to investigate the association between medically or occupationally related exposure to ionising radiation and brain tumours. METHODS: We...... used self-reported medical and occupational data collected during the German part of a multinational case-control study on mobile phone use and the risk of brain tumours (Interphone study) for the analyses. RESULTS: For any exposure to medical ionising radiation we found odds ratios (ORs) of 0.63 (95...... regions. CONCLUSION: We did not find any significant increased risk of brain tumours for exposure to medical ionising radiation....

  4. Transition from non-sequential to sequential double ionisation in many-electron systems

    CERN Document Server

    Pullen, Michael G; Wang, Xu; Tong, Xiao-Min; Sclafani, Michele; Baudisch, Matthias; Pires, Hugo; Schröter, Claus Dieter; Ullrich, Joachim; Pfeifer, Thomas; Moshammer, Robert; Eberly, J H; Biegert, Jens

    2016-01-01

    Obtaining a detailed understanding of strong-field double ionisation of many-electron systems (heavy atoms and molecules) remains a challenging task. By comparing experimental and theoretical results in the mid-IR regime, we have unambiguously identified the transition from non-sequential (e,2e) to sequential double ionisation in Xe and shown that it occurs at an intensity below $10^{14}$ Wcm$^{-2}$. In addition, our data demonstrate that ionisation from the Xe 5s orbital is decisive at low intensities. Moreover, using the acetylene molecule, we propose how sequential double ionisation in the mid-IR can be used to study molecular dynamics and fragmentation on unprecedented few-femtosecond timescales.

  5. Chronic boron exposure and human semen parameters.

    Science.gov (United States)

    Robbins, Wendie A; Xun, Lin; Jia, Juan; Kennedy, Nola; Elashoff, David A; Ping, Liu

    2010-04-01

    Boron found as borates in soil, food, and water has important industrial and medical applications. A panel reviewing NTP reproductive toxicants identified boric acid as high priority for occupational studies to determine safe versus adverse reproductive effects. To address this, we collected boron exposure/dose measures in workplace inhalable dust, dietary food/fluids, blood, semen, and urine from boron workers and two comparison worker groups (n=192) over three months and determined correlations between boron and semen parameters (total sperm count, sperm concentration, motility, morphology, DNA breakage, apoptosis and aneuploidy). Blood boron averaged 499.2 ppb for boron workers, 96.1 and 47.9 ppb for workers from high and low environmental boron areas (pBoron concentrated in seminal fluid. No significant correlations were found between blood or urine boron and adverse semen parameters. Exposures did not reach those causing adverse effects published in animal toxicology work but exceeded those previously published for boron occupational groups.

  6. Nailfold Capillaroscopic Monitoring as Preventive Medicine in Subjects Exposed to Ionising Radiation

    Energy Technology Data Exchange (ETDEWEB)

    Pennarola, R.; Perdereau, B.; Trenta, G.; Cosset, J. M.

    2004-07-01

    Capillaroscopy consists of in vivo observation of microvessels using special microscopes with a short focal length. Normally, when looking at the nail fold, where capillaroscopy is commonly used, the capillaries ares arranged like hairpins, lined up in parallel or obliquely to the field of vision in three or four layers above the subpapillary venous network, approximately 20 loops per mm''2. Ionising radiation can badly damage the skin and underlying tissues. The capillary network is among the first structures to show an effect. Moderate doses of radiation cause damage endothelial cells with hypertrophy or hyperplasia of endothelial cells, which can block capillaries while having little effect on larger vessels. Occlusion of capillaries impedes blood flow no only in nearby tissue but also in areas farther away. Capillaroscopic examination of the nail fold is irreplaceable in the field of radioprotection especially in cases of exposure of the hands. Nailfold capillaroscopic monitoring lets us observe the degree to which qualitative and quantitative alterations of the capillaries are a function of the evolution of the lesion. Therefore, for biological monitoring of subjects exposed to radiation the authors propose to use this microvascular quantitative analysis of the nailfold region. Experience, matured over many years by our team, highlights the relation between the sum of repeated exposure and the importance of tissue alterations evidenced by microcirculation. (Author) 9 refs.

  7. PGNAA of human arthritic synovium for boron neutron capture synovectomy

    Energy Technology Data Exchange (ETDEWEB)

    Binello, E.; Yanch, J.C. [Massashucetts Institute of Technology, Cambridge, MA (United States); Shortkroff, S. [Brigham and Women`s Hospital, Boston, MA (United States)

    1997-12-01

    Boron neutron capture synovectomy (BNCS), is a proposed new therapy modality for the treatment of rheumatoid arthritis, an autoimmune disease afflicting the joints. The synovium, which is the membrane lining the joint, becomes inflamed and represents the target tissue for therapy. When a joint is unresponsive to drug treatment, physical removal of the synovium, termed synovectomy, becomes necessary. Existing options include surgery and radiation synovectomy. BNCS has advantages over these options in that it is noninvasive and does not require the administration of radioactive substances. Previous studies have shown that the uptake of {sup 10}B by human arthritic synovium ex vivo is high, ranging from 194 to 545 ppm with an unenriched boron compound. While tissue samples remain viable up to 1 week, ex vivo conditions do not accurately reflect those in vivo. This paper presents results from experiments assessing the washout of boron from the tissue and examines the implications for in vivo studies.

  8. Simulating the 21-cm signal from reionisation including non-linear ionisations and inhomogeneous recombinations

    OpenAIRE

    Hassan, Sultan; Davé, Romeel; Finlator, Kristian; Santos, Mario G.

    2015-01-01

    We explore the impact of incorporating physically motivated ionisation and recombination rates on the history and topology of cosmic reionisation, by incorporating inputs from small-volume hydrodynamic simulations into a semi-numerical code, SimFast21, that evolves reionisation on large scales. We employ radiative hydrodynamic simulations to parameterize the ionisation rate Rion and recombination rate Rrec as functions of halo mass, overdensity and redshift. We find that Rion is super-linearl...

  9. Boron-Based Nanostructures, Stability, Functionality and Synthetic Routes

    Energy Technology Data Exchange (ETDEWEB)

    Yakobson, Boris I. [Rice Univ., Houston, TX (United States); Ajayan, Pulickel M. [Rice Univ., Houston, TX (United States)

    2017-08-04

    Boron (B) is one of the most intriguing elements not only because of its position between metals and nonmetals in periodic table but also because of its ability to form an enormous number of allotropes. Apart from several bulk three-dimensional (3D) phases, boron can form 0D clusters, 1D nanotubes and nanowires, and 2D layers. In particular, boron sheets of monoatomic thickness have raised interest as a potential new 2D-material and as a (conceptual) precursor, for example, so-called α-sheets, from which other boron structures - fullerene cages and tubes - might be constructed. In fact, a number of planar B clusters up to tens of atoms, found in experiments, appear as seeds for extended sheets. In this project we developed theoretical methods to guide synthesis, have successfully identified the material substrates (Ag, Au, Cu) to producing the pure boron layers, and further even predicted what atomistic structures should be expected. These guidelines have successfully led to discoveries in several labs and now have grown into an active line of research worldwide.

  10. Influence of easily ionised elements on the delayed responses of the emission intensities of an analyte in a power modulated U-shaped argon stabilised DC arc plasma with an aerosol supply

    Directory of Open Access Journals (Sweden)

    MIROSLAV KUZMANOVIC

    2005-09-01

    Full Text Available The current of a U-shaped argon stabilised DC arc was square modulated with a 40 Hz repetition frequency between 6 and 3 A. The delayed line intensity responses to the modulation of the arc current were investigated using calcium as a representative analyte. The intensities of both the atomic and ionic lines were monitored at different distances from the arc axis in the presence of various concentrations of the easily ionised element. Temporal evolutions were monitored on a millisecond time scale. It was found that the responses of the line intesity to the arc current change strongly depended on the observed radial position, especially in the vicinity of the arc axis. The obtained results showed a significant influence of even small amounts of the easily ionised element on the excitation and transport of the analyte and indicated a way of possibly improving the analytical capabilities of the excitation source.

  11. ER stress induced by ionising radiation in IEC-6 cells.

    Science.gov (United States)

    Zhang, Bo; Wang, Yan; Pang, Xueli; Su, Yongping; Ai, Guoping; Wang, Tao

    2010-06-01

    Ionising radiation (IR) can evoke a series of biochemical events inside the cell. However, whether IR can directly induce endoplasmic reticulum (ER) stress is not clear. In our previous study, we found that there might be a causative link between IR and ER stress. In this study, we further characterised the type of ER stress induced by IR. Rat intestinal epithelial cells IEC-6 were irradiated at a dose of 10 Gy, and total RNA and proteins were harvested at indicated time points. The mRNA and protein expression of immunoglobulin heavy chain binding protein (BiP) and glucose regulated protein 94 (GRP94) was detected along with proteins associated with ER stress signal pathways. Our results indicated that IR induced up-regulation of ER stress marker including BiP and GRP94 at protein and mRNA levels in IEC-6 cells. Increased phosphorylation of eukaryotic translation initiation factor 2 (eIF2alpha) and induced mRNA splicing of X-box binding protein 1 (XBP1) suggested that PERK (interferon-induced double-stranded RNA-activated protein kinase (PRKR) -like endoplasmic reticulum kinase) and IRE1 (inositol requirement 1) signal transduction pathways were involved in this kind of ER stress. However, the active form of activating transcription factor 6 (ATF6) did not change significantly in irradiated cells, which suggested that the ATF6 pathway was not involved. Thus, we concluded that IR could induce moderate ER stress directly in IEC-6 cells.

  12. Martian sub-surface ionising radiation: biosignatures and geology

    Directory of Open Access Journals (Sweden)

    J. M. Ward

    2007-07-01

    Full Text Available The surface of Mars, unshielded by thick atmosphere or global magnetic field, is exposed to high levels of cosmic radiation. This ionising radiation field is deleterious to the survival of dormant cells or spores and the persistence of molecular biomarkers in the subsurface, and so its characterisation is of prime astrobiological interest. Here, we present modelling results of the absorbed radiation dose as a function of depth through the Martian subsurface, suitable for calculation of biomarker persistence. A second major implementation of this dose accumulation rate data is in application of the optically stimulated luminescence technique for dating Martian sediments.

    We present calculations of the dose-depth profile in the Martian subsurface for various scenarios: variations of surface composition (dry regolith, ice, layered permafrost, solar minimum and maximum conditions, locations of different elevation (Olympus Mons, Hellas basin, datum altitude, and increasing atmospheric thickness over geological history. We also model the changing composition of the subsurface radiation field with depth compared between Martian locations with different shielding material, determine the relative dose contributions from primaries of different energies, and discuss particle deflection by the crustal magnetic fields.

  13. Dosimetry of ionising radiation in modern radiation oncology

    Science.gov (United States)

    Kron, Tomas; Lehmann, Joerg; Greer, Peter B.

    2016-07-01

    Dosimetry of ionising radiation is a well-established and mature branch of physical sciences with many applications in medicine and biology. In particular radiotherapy relies on dosimetry for optimisation of cancer treatment and avoidance of severe toxicity for patients. Several novel developments in radiotherapy have introduced new challenges for dosimetry with small and dynamically changing radiation fields being central to many of these applications such as stereotactic ablative body radiotherapy and intensity modulated radiation therapy. There is also an increasing awareness of low doses given to structures not in the target region and the associated risk of secondary cancer induction. Here accurate dosimetry is important not only for treatment optimisation but also for the generation of data that can inform radiation protection approaches in the future. The article introduces some of the challenges and highlights the interdependence of dosimetric calculations and measurements. Dosimetric concepts are explored in the context of six application fields: reference dosimetry, small fields, low dose out of field, in vivo dosimetry, brachytherapy and auditing of radiotherapy practice. Recent developments of dosimeters that can be used for these purposes are discussed using spatial resolution and number of dimensions for measurement as sorting criteria. While dosimetry is ever evolving to address the needs of advancing applications of radiation in medicine two fundamental issues remain: the accuracy of the measurement from a scientific perspective and the importance to link the measurement to a clinically relevant question. This review aims to provide an update on both of these.

  14. Dedicated Trigger for Highly Ionising Particles at ATLAS

    CERN Document Server

    Katre, Akshay; The ATLAS collaboration

    2015-01-01

    In 2012, a novel strategy was designed to detect signatures of Highly Ionising Particles (HIPs) such as magnetic monopoles, dyons or Qballs with the ATLAS trigger system. With proton-proton collisions at a centre of mass enegy of 8 TeV, the trigger was designed to have unique properties as a tracker for HIPs. It uses only the Transition Radiation Tracker (TRT) system, applying an algorithm distinct from standard tracking ones. The unique high threshold readout capability of the TRT is used at the location where HIPs in the detector are looked for. In particular the number and the fraction of TRT high threshold hits is used to distinguish HIPs from background processes. The trigger requires significantly lower energy depositions in the electro-magnetic calorimeters as a seed unlike previously used trigger algorithms for such searches. Thus the new trigger is capable of probing a large range of HIP masses and charges. We will give a description of the algorithms for this newly developed trigger for HIP searches...

  15. Rapid accurate isotopic measurements on boron in boric acid and boron carbide.

    Science.gov (United States)

    Duchateau, N L; Verbruggen, A; Hendrickx, F; De Bièvre, P

    1986-04-01

    A procedure is described whereby rapid and accurate isotopic measurements can be performed on boron in boric acid and boron carbide after fusion of these compounds with calcium carbonate. It allows the determination of the isotopic composition of boron in boric acid and boron carbide and the direct assay of boron or the (10)B isotope in boron carbide by isotope-dilution mass spectrometry.

  16. A new and effective approach to boron removal by using novel boron-specific fungi isolated from boron mining wastewater.

    Science.gov (United States)

    Taştan, Burcu Ertit; Çakir, Dilara Nur; Dönmez, Gönül

    2016-01-01

    Boron-resistant fungi were isolated from the wastewater of a boron mine in Turkey. Boron removal efficiencies of Penicillium crustosum and Rhodotorula mucilaginosa were detected in different media compositions. Minimal Salt Medium (MSM) and two different waste media containing molasses (WM-1) or whey + molasses (WM-2) were tested to make this process cost effective when scaled up. Both isolates achieved high boron removal yields at the highest boron concentrations tested in MSM and WM-1. The maximum boron removal yield by P. crustosum was 45.68% at 33.95 mg l(-1) initial boron concentration in MSM, and was 38.97% at 42.76 mg l(-1) boron for R. mucilaginosa, which seemed to offer an economically feasible method of removing boron from the effluents.

  17. Boron-10 ABUNCL Prototype Initial Testing

    Energy Technology Data Exchange (ETDEWEB)

    Kouzes, Richard T.; Ely, James H.; Lintereur, Azaree T.; Siciliano, Edward R.

    2012-12-01

    The Department of Energy Office of Nuclear Safeguards and Security (NA-241) is supporting the project Coincidence Counting With Boron-Based Alternative Neutron Detection Technology at Pacific Northwest National Laboratory (PNNL) for the development of a 3He proportional counter alternative neutron coincidence counter. The goal of this project is to design, build and demonstrate a system based upon 10B-lined proportional tubes in a configuration typical for 3He-based coincidence counter applications. This report provides results of initial testing of an Alternative Boron-Based Uranium Neutron Coincidence Collar (ABUNCL) design built by General Electric Reuter-Stokes. Several configurations of the ABUNCL models, which use 10B-lined proportional counters in place of 3He proportional counters for the neutron detection elements, were previously reported. The ABUNCL tested is of a different design than previously modeled. Initial experimental testing of the as-delivered passive ABUNCL was performed, and modeling will be conducted. Testing of the system reconfigured for active testing will be performed in the near future, followed by testing with nuclear fuel.

  18. Nothing Boring About Boron

    Science.gov (United States)

    Pizzorno, Lara

    2015-01-01

    The trace mineral boron is a micronutrient with diverse and vitally important roles in metabolism that render it necessary for plant, animal, and human health, and as recent research suggests, possibly for the evolution of life on Earth. As the current article shows, boron has been proven to be an important trace mineral because it (1) is essential for the growth and maintenance of bone; (2) greatly improves wound healing; (3) beneficially impacts the body’s use of estrogen, testosterone, and vitamin D; (4) boosts magnesium absorption; (5) reduces levels of inflammatory biomarkers, such as high-sensitivity C-reactive protein (hs-CRP) and tumor necrosis factor α (TNF-α); (6) raises levels of antioxidant enzymes, such as superoxide dismutase (SOD), catalase, and glutathione peroxidase; (7) protects against pesticide-induced oxidative stress and heavy-metal toxicity; (8) improves the brains electrical activity, cognitive performance, and short-term memory for elders; (9) influences the formation and activity of key biomolecules, such as S-adenosyl methionine (SAM-e) and nicotinamide adenine dinucleotide (NAD+); (10) has demonstrated preventive and therapeutic effects in a number of cancers, such as prostate, cervical, and lung cancers, and multiple and non-Hodgkin’s lymphoma; and (11) may help ameliorate the adverse effects of traditional chemotherapeutic agents. In none of the numerous studies conducted to date, however, do boron’s beneficial effects appear at intakes > 3 mg/d. No estimated average requirements (EARs) or dietary reference intakes (DRIs) have been set for boron—only an upper intake level (UL) of 20 mg/d for individuals aged ≥ 18 y. The absence of studies showing harm in conjunction with the substantial number of articles showing benefits support the consideration of boron supplementation of 3 mg/d for any individual who is consuming a diet lacking in fruits and vegetables or who is at risk for or has osteopenia; osteoporosis

  19. Re-entrant-Groove-Assisted VLS Growth of Boron Carbide Five-Fold Twinned Nanowires

    Institute of Scientific and Technical Information of China (English)

    FU Xin; JIANG Jun; LIU Chao; YU Zhi-Yang; Steffan LEA; YUAN Jun

    2009-01-01

    We report a preferential growth of boron carbide nanowires with a Eve-fold twinned internal structure.The nanowires are found to grow catalytically via iron boron nanoparticles,but unusually the catalytic particle is in contact with the low-energy surfaces of boron carbide with V-shaped contact lines.We propose that this catalytical growth may be caused by preferential nucleation at the re-entrant grooves due to the twinning planes,followed by rapid spreading of atomic steps.This is consistent with the observed temperature dependence of the five-fold twinned nanowire growth.

  20. Boronated monoclonal antibodies for potential neutron capture therapy of malignant melanoma and leukaemia

    Energy Technology Data Exchange (ETDEWEB)

    Tamat, S.R.; Patwardhan, A.; Moore, D.E.; Kabral, A.; Bradstock, K.; Hersey, P.; Allen, B.J.

    The authors report a preparation and characterisation of boronated melanoma and leukaemia antibodies and the separation from native antibody by anion exchange liquid chromatography. Two types of biodistribution experiments were performed with the boronated melanoma antibody 225.28S using Balb/c derived nude mice in which melanoma tumours had been raised in the thigh by subcutaneous injection of a human malignant melanoma cell line, designated CMC. From these experiments, one may conclude that the boronated antibody has the ability to localise in the melanoma following systemic injection, but more efficient use of the preparation is achieved with perilesional administration.

  1. Structural characterization of electrodeposited boron

    Indian Academy of Sciences (India)

    Ashish Jain; C Ghosh; T R Ravindran; S Anthonysamy; R Divakar; E Mohandas; G S Gupta

    2013-12-01

    Structural characterization of electrodeposited boron was carried out by using transmission electron microscopy and Raman spectroscopy. Electron diffraction and phase contrast imaging were carried out by using transmission electron microscopy. Phase identification was done based on the analysis of electron diffraction patterns and the power spectrum calculated from the lattice images from thin regions of the sample. Raman spectroscopic examination was carried out to study the nature of bonding and the allotropic form of boron obtained after electrodeposition. The results obtained from transmission electron microscopy showed the presence of nanocrystallites embedded in an amorphous mass of boron. Raman microscopic studies showed that amorphous boron could be converted to its crystalline form at high temperatures.

  2. Analysis of boron dilution in a four-loop PWR

    Energy Technology Data Exchange (ETDEWEB)

    Sun, J.G.; Sha, W.T. [Argonne National Lab., IL (United States)

    1995-03-01

    Thermal mixing and boron dilution in a pressurized water reactor were analyzed with COMMIX codes. The reactor system was the four-loop Zion reactor. Two boron dilution scenarios were analyzed. In the first scenario, the plant is in cold shutdown and the reactor coolant system has just been filled after maintenance on the steam generators. To flush the air out of the steam generator tubes, a reactor coolant pump (RCP) is started, with the water in the pump suction line devoid of boron and at the same temperature as the coolant in the system. In the second scenario, the plant is at hot standby and the reactor coolant system has been heated to operating temperature after a long outage. It is assumed that an RCP is started, with the pump suction line filled with cold unborated water, forcing a slug of diluted coolant down the downcomer and subsequently through the reactor core. The subsequent transient thermal mixing and boron dilution that would occur in the reactor system is simulated for these two scenarios. The reactivity insertion rate and the total reactivity are evaluated and a sensitivity study is performed to assess the accuracy of the numerical modeling of the geometry of the reactor coolant system.

  3. Analysis of boron dilution in a four-loop PWR

    Energy Technology Data Exchange (ETDEWEB)

    Sun, J.G.; Sha, W.T.

    1995-12-31

    Thermal mixing and boron dilution in a pressurized water reactor were analyzed with COMMIX codes. The reactor system was the four loop Zion reactor. Two boron dilution scenarios were analyzed. In the first scenario, the plant is in cold shutdown and the reactor coolant system has just been filled after maintenance on the steam generators. To flush the air out of the steam generator tubes, a reactor coolant pump (RCP) is started, with the water in the pump suction line devoid of boron and at the same temperature as the coolant in the system. In the second scenario, the plant is at hot standby and the reactor coolant system has been heated up to operating temperature after a long outage. It is assumed that an RCP is started, with the pump suction line filled with cold unborated water, forcing a slug of diluted coolant down the downcomer and subsequently through the reactor core. The subsequent transient thermal mixing and boron dilution that would occur in the reactor system is simulated for these two scenarios. The reactivity insertion rate and the total reactivity are evaluated.

  4. Nanostructured Boron Nitride With High Water Dispersibility For Boron Neutron Capture Therapy

    Science.gov (United States)

    Singh, Bikramjeet; Kaur, Gurpreet; Singh, Paviter; Singh, Kulwinder; Kumar, Baban; Vij, Ankush; Kumar, Manjeet; Bala, Rajni; Meena, Ramovatar; Singh, Ajay; Thakur, Anup; Kumar, Akshay

    2016-10-01

    Highly water dispersible boron based compounds are innovative and advanced materials which can be used in Boron Neutron Capture Therapy for cancer treatment (BNCT). Present study deals with the synthesis of highly water dispersible nanostructured Boron Nitride (BN). Unique and relatively low temperature synthesis route is the soul of present study. The morphological examinations (Scanning/transmission electron microscopy) of synthesized nanostructures showed that they are in transient phase from two dimensional hexagonal sheets to nanotubes. It is also supported by dual energy band gap of these materials calculated from UV- visible spectrum of the material. The theoretically calculated band gap also supports the same (calculated by virtual nano lab Software). X-ray diffraction (XRD) analysis shows that the synthesized material has deformed structure which is further supported by Raman spectroscopy. The structural aspect of high water disperse ability of BN is also studied. The ultra-high disperse ability which is a result of structural deformation make these nanostructures very useful in BNCT. Cytotoxicity studies on various cell lines (Hela(cervical cancer), human embryonic kidney (HEK-293) and human breast adenocarcinoma (MCF-7)) show that the synthesized nanostructures can be used for BNCT.

  5. The Ionising Radiations Advisory Committee Open Meeting 10 October 2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-12-01

    Full text: The Ionising Radiations Advisory Committee (IRAC) held its first open meeting on 10 October 2001 in response to a request from the Health and Safety Commission (HSC) that all its advisory committees should follow the Commission's example and hold such meetings. Some of the other advisory committees have already held open meetings and others are planning to do so shortly. The aim of the meeting was to enable members of the public to meet IRAC members and to find out more about the Committee - how it worked and the type of issues it dealt with. The first two sessions were devoted to short presentations describing IRAC's work and influences, now and in the future, on radiation protection generally. The third session was a discussion forum. The agenda for the meeting and the presentations are posted on the web at: www.hse.gov.uk/foi/iracopen.htm. Each session of presentations was followed by questions of clarification and the third session of the meeting comprised an open forum. Many of the questions raised were not directly relevant to IRAC but, nevertheless, members provided brief responses and referred questions on to others as appropriate. One question had been notified in advance, asking whether members of IRAC agreed that it is now (regrettably) reasonably foreseeable that a loss of containment of radioactive material may occur at a nuclear facility as a result of impact by an aeroplane or by other hostile acts, and that this should be made clear in published guidance on REPPIR. This question was not within IRAC's remit. The Chairman of the Nuclear Safety Advisory Committee offered to take the question to the Committee's next meeting. Issues discussed included: Concerns that exposure to ionising radiation at low levels is more dangerous than is currently reflected in risk estimates. The European Parliament has adopted a resolution calling on the main international bodies, including the International Commission on Radiological

  6. Excitation and Ionisation dynamics in high-frequency plasmas

    Science.gov (United States)

    O'Connell, D.

    2008-07-01

    Non-thermal low temperature plasmas are widely used for technological applications. Increased demands on plasma technology have resulted in the development of various discharge concepts based on different power coupling mechanisms. Despite this, power dissipation mechanisms in these discharges are not yet fully understood. Of particular interest are low pressure radio-frequency (rf) discharges. The limited understanding of these discharges is predominantly due to the complexity of the underlying mechanisms and difficult diagnostic access to important parameters. Optical measurements are a powerful diagnostic tool offering high spatial and temporal resolution. Optical emission spectroscopy (OES) provides non-intrusive access, to the physics of the plasma, with comparatively simple experimental requirements. Improved advances in technology and modern diagnostics now allow deeper insight into fundamental mechanisms. In low pressure rf discharges insight into the electron dynamics within the rf cycle can yield vital information. This requires high temporal resolution on a nano-second time scale. The optical emission from rf discharges exhibits temporal variations within the rf cycle. These variations are particularly strong, in for example capacitively coupled plasmas (CCPs), but also easily observable in inductively coupled plasmas (ICPs), and can be exploited for insight into power dissipation. Interesting kinetic and non-linear coupling effects are revealed in capacitive systems. The electron dynamics exhibits a complex spatio-temporal structure. Excitation and ionisation, and, therefore, plasma sustainment is dominated through directed energetic electrons created through the dynamics of the plasma boundary sheath. In the relatively simple case of an asymmetric capacitively coupled rf plasma the complexity of the power dissipation is exposed and various mode transitions can be clearly observed and investigated. At higher pressure secondary electrons dominate the

  7. Boron diffusion in silicon devices

    Science.gov (United States)

    Rohatgi, Ajeet; Kim, Dong Seop; Nakayashiki, Kenta; Rounsaville, Brian

    2010-09-07

    Disclosed are various embodiments that include a process, an arrangement, and an apparatus for boron diffusion in a wafer. In one representative embodiment, a process is provided in which a boric oxide solution is applied to a surface of the wafer. Thereafter, the wafer is subjected to a fast heat ramp-up associated with a first heating cycle that results in a release of an amount of boron for diffusion into the wafer.

  8. Combustion of boron containing compositions

    Energy Technology Data Exchange (ETDEWEB)

    Frolov, Y.; Pivkina, A. [Institute of Chemical Physics, Russian Academy of Science, Moscow (Russian Federation)

    1996-12-31

    Boron is one of the most energetic components for explosives, propellants and for heterogeneous condensed systems in common. The combustion process of mixtures of boron with different oxidizers was studied. The burning rate, concentration combustion limits, the agglomeration and dispersion processes during reaction wave propagation were analysed in the respect of the percolation theory. The linear dependence of the burning rate on the contact surface value was demonstrated. The percolative model for the experimental results explanation is proposed. (authors) 5 refs.

  9. Determination of the boron content in polyethylene samples using the reactor Orphée

    CERN Document Server

    Gunsing, F; Aberle, O

    2017-01-01

    The boron content of two unknown types of polyethylene has been determined relative to a known reference type. Samples of polyethylene, including a known boron-less one, were irradiated with thermal neutrons at the reactor Orphée at Saclay in France. Prompt gamma rays were measured with a CeBr$_3$ detector and the intensity of the 478~keV line from $^{10}${B}(n,$\\alpha_1\\gamma$)$^{7}{Li*} was extracted.

  10. Kinematics of Ionised Gas in the Barred Seyfert Galaxy NGC 4151

    CERN Document Server

    Asif, M W; Pedlar, A

    2005-01-01

    We have determined the structure and kinematics of ionised gas in the weak oval bar of the archetypal Seyfert 1 galaxy, NGC 4151, using the TAURUS Fabry-Perot interferometer to simultaneously map the distribution and kinematics of Hbeta emission. We also present broad-band ultraviolet imaging of the host galaxy, obtained with XMM-Newton, that shows the detailed distribution of star formation in the bar and in the optically-faint outer spiral arms. We compare the distribution and kinematics of ionised gas with that previously determined in neutral hydrogen by Mundell & Shone; we suggest that the distribution of bright, patchy UV emission close to the HI shocks is consistent with ionisation by star clusters that have formed in compressed pre-shock gas. These clusters then travel ballistically through the gaseous shock to ionise gas downstream along the leading edge of the bar. In addition, we detect, for the first time, ionised gas within the shock itself which is streaming to smaller radii in the same mann...

  11. Student and intern awareness of ionising radiation exposure from common diagnostic imaging procedures.

    Science.gov (United States)

    Zhou, G Z; Wong, D D; Nguyen, L K; Mendelson, R M

    2010-02-01

    This study aims to evaluate medical student and intern awareness of ionising radiation exposure from common diagnostic imaging procedures and to suggest how education could be improved. Fourth to sixth year medical students enrolled at a Western Australian university and interns from three teaching hospitals in Perth were recruited. Participants were asked to complete a questionnaire consisting of 26 questions on their background, knowledge of ionising radiation doses and learning preferences for future teaching on this subject. A total of 331 completed questionnaires were received (95.9%). Of the 17 questions assessing knowledge of ionising radiation, a mean score of 6.0 was obtained by respondents (95% CI 5.8-6.2). Up to 54.8% of respondents underestimated the radiation dose from commonly requested radiological procedures. Respondents (11.3 and 25.5%) incorrectly believed that ultrasound and MRI emit ionising radiation, respectively. Of the four subgroups of respondents, the intern doctor subgroup performed significantly better (mean score 6.9, P medical student subgroups. When asked for the preferred method of teaching for future radiation awareness, a combination of lectures, tutorials and workshops was preferred. This study has clearly shown that awareness of ionising radiation from diagnostic imaging is lacking among senior medical students and interns. The results highlight the need for improved education to minimise unnecessary exposure of patients and the community to radiation. Further studies are required to determine the most effective form of education.

  12. Formation of the helium EUV resonance lines

    CERN Document Server

    Golding, Thomas Peter; Carlsson, Mats

    2016-01-01

    Context: While classical models successfully reproduce intensities of many transition region lines, they predict helium EUV line intensities roughly an order of magnitude lower than the observed value. Aims: To determine the relevant formation mechanism(s) of the helium EUV resonance lines, capable of explaining the high intensities under quiet sun conditions. Methods: We synthesise and study the emergent spectra from a 3D radiation-magnetohydrodynamics simulation model. The effects of coronal illumination and non-equilibrium ionisation of hydrogen and helium are included self-consistently in the numerical simulation. Results: Radiative transfer calculations result in helium EUV line intensities that are an order of magnitude larger than the intensities calculated under the classical assumptions. The enhanced intensity of He I 584 is primarily caused by He II recombination cascades. The enhanced intensity of He II 304 and He II 256 is caused primarily by non-equilibrium helium ionisation. Conclusion: The anal...

  13. Preparation of High Purity Amorphous Boron Powder

    Directory of Open Access Journals (Sweden)

    K.V. Tilekar

    2005-10-01

    Full Text Available Amorphous boron powder of high purity (92-94 % with a particle size of l-2 mm is preferred as a fuel for fuel-rich propellants for integrated rocket ramjets and for igniter formulations. Thispaper describes the studies on process optimisation of two processes, ie, oxidative roasting of boron (roasting boron in air and roasting boron with zinc in an inert medium for preparing high purity boron. Experimental studies reveal that roasting boron with zinc at optimised process conditions yields boron of purity more than 93 per cent, whereas oxidative roasting method yields boron of purity - 92 per cent. Oxidative roasting has comparative edge over the other processes owing to its ease of scale-up and simplicity

  14. The biological effects of ionising radiation on Crustaceans: A review

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Neil; Lerebours, Adélaïde [Institute of Marine Sciences, School of Biological Sciences, University of Portsmouth, Ferry Road, Portsmouth, Hampshire PO4 9LY (United Kingdom); Smith, Jim T. [School of Earth & Environmental Sciences, University of Portsmouth, Burnaby Building, Burnaby Road, Portsmouth, Hampshire PO1 3QL (United Kingdom); Ford, Alex T., E-mail: alex.ford@port.ac.uk [Institute of Marine Sciences, School of Biological Sciences, University of Portsmouth, Ferry Road, Portsmouth, Hampshire PO4 9LY (United Kingdom)

    2015-10-15

    Highlights: • We comprehensively review the effects of ionising radiation in crustaceans. • Current environmental radioprotection levels found to be inadequate in some cases. • Mutation is shown to be a sensitive endpoint of radiation exposure. • Lowest observed effect dose rate varies by orders of magnitude. - Abstract: Historic approaches to radiation protection are founded on the conjecture that measures to safeguard humans are adequate to protect non-human organisms. This view is disparate with other toxicants wherein well-developed frameworks exist to minimise exposure of biota. Significant data gaps for many organisms, coupled with high profile nuclear incidents such as Chernobyl and Fukushima, have prompted the re-evaluation of our approach toward environmental radioprotection. Elucidating the impacts of radiation on biota has been identified as priority area for future research within both scientific and regulatory communities. The crustaceans are ubiquitous in aquatic ecosystems, comprising greater than 66,000 species of ecological and commercial importance. This paper aims to assess the available literature of radiation-induced effects within this subphylum and identify knowledge gaps. A literature search was conducted pertaining to radiation effects on four endpoints as stipulated by a number of regulatory bodies: mortality, morbidity, reproduction and mutation. A major finding of this review was the paucity of data regarding the effects of environmentally relevant radiation doses on crustacean biology. Extremely few studies utilising chronic exposure durations or wild populations were found across all four endpoints. The dose levels at which effects occur was found to vary by orders of magnitude thus presenting difficulties in developing phyla-specific benchmark values and reference levels for radioprotection. Based on the limited data, mutation was found to be the most sensitive endpoint of radiation exposure, with mortality the least sensitive

  15. Solar Hard X-ray Source Sizes in a Beam-Heated and Ionised Chromosphere

    CERN Document Server

    O'Flannagain, A; Gallagher, P T

    2014-01-01

    Solar flare hard X-rays (HXRs) are produced as bremsstrahlung when an accelerated population of electrons interacts with the dense chromospheric plasma. HXR observations presented by using the Ramaty High-Energy Solar Spectroscopic Imager (RHESSI) have shown that HXR source sizes are 3-6 times more extended in height than those predicted by the standard collisional thick target model (CTTM). Several possible explanations have been put forward including the multi-threaded nature of flare loops, pitch-angle scattering, and magnetic mirroring. However, the nonuniform ionisation (NUI) structure along the path of the electron beam has not been fully explored as a solution to this problem. Ionised plasma is known to be less effective at producing nonthermal bremsstrahlung HXRs when compared to neutral plasma. If the peak HXR emission was produced in a locally ionised region within the chromosphere, the intensity of emission will be preferentially reduced around this peak, resulting in a more extended source. Due to...

  16. The spatial damping of magnetohydrodynamic waves in a flowing partially ionised prominence plasma

    CERN Document Server

    Carbonell, M; Oliver, R; Ballester, J L

    2010-01-01

    Solar prominences are partially ionised plasmas displaying flows and oscillations. These oscillations show time and spatial damping and, commonly, have been explained in terms of magnetohydrodynamic (MHD) waves. We study the spatial damping of linear non-adiabatic MHD waves in a flowing partially ionised plasma, having prominence-like physical properties. We consider single fluid equations for a partially ionised hydrogen plasma including in the energy equation optically thin radiation, thermal conduction by electrons and neutrals, and heating. Keeping the frequency real and fixed, we have solved the obtained dispersion relations for the complex wavenumber, k, and have analysed the behaviour of the damping length, wavelength and the ratio of the damping length to the wavelength, versus period, for Alfven, fast, slow and thermal waves.

  17. The ionisation energy of cyclopentadienone: a photoelectron-photoion coincidence study

    Science.gov (United States)

    Ormond, Thomas K.; Hemberger, Patrick; Troy, Tyler P.; Ahmed, Musahid; Stanton, John F.; Ellison, G. Barney

    2015-08-01

    Imaging photoelectron photoion coincidence (iPEPICO) spectra of cyclopentadienone (C5H4=O and C5D4=O) have been measured at the Swiss Light Source Synchrotron (Paul Scherrer Institute, Villigen, Switzerland) at the Vacuum Ultraviolet (VUV) Beamline. Complementary to the photoelectron spectra, photoionisation efficiency curves were measured with tunable VUV radiation at the Chemical Dynamics Beamline at the Advanced Light Source Synchrotron (Lawrence Berkeley National Laboratory, Berkeley, CA, USA). For both experiments, molecular beams diluted in argon and helium were generated from the vacuum flash pyrolysis of o-phenylene sulphite in a resistively heated microtubular SiC flow reactor. The Franck-Condon profiles and ionisation energies were calculated at the CCSD(T) level of theory, and are in excellent agreement with the observed iPEPICO spectra. The ionisation energies of both cyclopentadienone-d0, IE(C5H4=O), and cyclopentadienone-d4, IE(C5D4=O), were observed to be the same: 9.41 ± 0.01 eV. The mass-selected threshold photoelectron spectrum (ms-TPES) of cyclopentadienone reveals that the C=C stretch in the ground state of the cation is excited upon ionisation, supporting computational evidence that the ground state of the cation is ? 2A2, and is in agreement with previous studies. However, the previously reported ionisation potential has been improved considerably in this work. In addition, since o-benzoquinone (o-O=C6H4=O and o-O=C6D4=O) is also produced in this process, its ms-TPES has been recorded. From the iPEPICO and photoionisation efficiency spectra, we infer an adiabatic ionisation energy of IE(o-O=C6H4=O) = 9.3 ± 0.1 eV, but the rather structureless spectrum indicates a strong change in geometry upon ionisation making this value less reliable.

  18. The Suzaku view of highly-ionised outflows in AGN: I - Statistical detection and global absorber properties

    CERN Document Server

    Gofford, Jason; Tombesi, Francesco; Braito, Valentina; Turner, T Jane; Miller, Lance; Cappi, Massimo

    2012-01-01

    We present the results of a new spectroscopic study of Fe K-band absorption in Active Galactic Nuclei (AGN). Using data obtained from the Suzaku public archive we have performed a statistically driven blind search for Fe XXV Hea and/or Fe XXVI Lyb absorption lines in a large sample of 51 type 1.0-1.9 AGN. Through extensive Monte Carlo simulations we find statistically significant absorption is detected at E>6.7 keV in 20/51 sources at the P(MC)>95% level, which corresponds to ~40% of the total sample. In all cases, individual absorption lines are detected independently and simultaneously amongst the two (or three) available XIS detectors which confirms the robustness of the line detections. The most frequently observed outflow phenomenology consists of two discrete absorption troughs corresponding to Fe XXV Hea and Fe XXVI Lyb at a common velocity shift. From xstar fitting the mean column density and ionisation parameter for the Fe K absorption components are log(NH/cm^{-2})~23 and log(xi/erg cm s^{-1})~4.5, ...

  19. Effect of factors on the extraction of boron from slags

    Science.gov (United States)

    Zhang, Peixin; Sui, Zhitong

    1995-04-01

    The effects of slag composition, additive agent, and heat treatment on the crystal morphologies, the crystallization behavior, and the efficiency of extraction of boron (EEB) from slags were investigated by chemical analysis, polarization microscope, and X-ray diffraction (XRD) as well as differential thermal analysis (DTA). The EEB varied with the slag composition. The farther the slag composition deviated from the line between 2MgO · B2O3 and 2MgO · SiO2 in the MgO-B2O3-SiO2 system, the lower the EEB. The EEB was directly related to the precipitating characteristics of the boron component in the slags. The EEB was high if the boron component existed in the form of a crystalline phase, otherwise the EEB was low when boron was in the form of an amorphous phase. The EEB from MgO-Al2O3-CaO-B2O3-SiO2 slag varied with the temperature of heat treatment; the highest EEB appeared at 1100 °C. The EEB and the crystallinities were increased by addition of TiO2 and MOx (M = Mg, Ca, Fe, Si). The effect of MOx was more notable than that of TiO2.

  20. Structures, stability, mechanical and electronic properties of a-boron and its twined brother a*-boron

    OpenAIRE

    He, Chaoyu; Zhong, Jianxin

    2013-01-01

    The structures, stability, mechanical and electronic properties of a-boron and its twined brother a*-boron have been studied by first-principles calculations. Both a-boron and a*-boron consist of equivalent icosahedra B12 clusters in different connecting configurations of "3S-6D-3S" and "2S-6D-4S", respectively. The total energy calculations show that a*-boron is less stable than a-boron but more favorable than beta-boron and Gamma-boron at zero pressure. Both a-boron and a*-boron are confirm...

  1. Coupled-channel calculations of K-shell ionisation in asymmetric collision systems

    Energy Technology Data Exchange (ETDEWEB)

    Mehler, G.; Greiner, W.; Soff, G.

    1987-06-28

    Theoretical results on K-shell ionisation for a variety of asymmetric collision systems are reported. The calculated ionisation rates are compared with experimental data. The coupled-channel formalism underlying these calculations is presented. It is based on a set of relativistic target centred states, taking a screened potential of Dirac-Fock-Slater type into account. The effects of different matrix elements are discussed, e.g. continuum-continuum couplings. The binding effect is inherently contained in the present approach and described in a dynamical way.

  2. A micro-gap, air-filled ionisation chamber as a detector for criticality accident dosimetry.

    Science.gov (United States)

    Murawski, Ł; Zielczyński, M; Golnik, N; Gryziński, M A

    2014-10-01

    A micro-gap air-filled ionisation chamber was designed for criticality dosimetry. The special feature of the chamber is its very small gap between electrodes of only 0.3 mm. This prevents ion recombination at high dose rates and minimises the influence of gas on secondary particles spectrum. The electrodes are made of polypropylene because of higher content of hydrogen in this material, when compared with soft tissue. The difference between neutron and gamma sensitivity in such chamber becomes practically negligible. The chamber's envelope contains two specially connected capacitors, one for polarising the electrodes and the other for collecting the ionisation charge.

  3. Tools to discover anionic and nonionic polyfluorinated alkyl surfactants by liquid chromatography electrospray ionisation mass spectrometry

    DEFF Research Database (Denmark)

    Trier, Xenia; Granby, Kit; Christensen, Jan H.

    2011-01-01

    A tiered approach is proposed for the discovery of unknown anionic and nonionic polyfluorinated alkyl surfactants (PFASs) by reversed phase ultra high performance liquid chromatography (UHPLC) – negative electrospray ionisation – quadrupole time of flight mass spectrometry (UHPLC......–ESI−–QTOF–MS). The chromatographic separation, ionisation and detection of PFASs mixtures, was achieved at high pH (pH=9.7) with NH4OH as additive. To distinguish PFASs from other chemicals we used the characteristic negative mass defects of PFASs, their specific losses of 20Da (HF) and the presence of series of chromatographic...

  4. Non-dissociative and dissociative ionisation of H sub 2 by 50-2000 keV antiprotons

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, L.H.; Hvelplund, P.; Knudsen, H.; Moeller, S.P.; Pedersen, J.O.P.; Tang-Petersen, S.; Uggerhoej, E. (Aarhus Univ. (Denmark). Inst. of Physics); Elsener, K. (European Organization for Nuclear Research, Geneva (Switzerland)); Morenzoni, E. (Paul Scherrer Inst. (PSI), Villigen (Switzerland))

    1990-08-14

    A beam of antiprotons with energies between 50 keV and 2 MeV has been used for measurements of non-dissociative ionisation and dissociative ionisation cross sections of H{sub 2}. The results are compared with cross sections for equivelocity protons and electrons, and the role of interference effects in two-electron processes is discussed. (author).

  5. Measurement of the electronic density of ionised media by hyper frequency methods; Mesure de la densite electronique des milieux ionises par des methodes hyperfrequences

    Energy Technology Data Exchange (ETDEWEB)

    Consoli, T. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    Within the limits of the I.N.S.T.N. courses on plasmas, this analytical study summarizes the articles quoted in the references on hyper-frequency techniques for the measurement of electronic density of an ionised gas. It is neither exhaustive nor complete and further details may be obtained by referring to the works mentioned. The first part, devoted to the theoretical side, concert the propagation of electromagnetic waves ionised media and the excitation of stationary raves in electromagnetic cavities. The second part deals with the measurement techniques themselves. It includes those techniques which hare become classic, and also more recent ones being developed in various laboratories and in the Service of Applied Physics at Saclay. (author) [French] Dans le cadre des cours sur les plasmas a l'l.N.S.T. cette etude d'analyse resume les articles cites en bibliographie sur les techniques hyperfrequences pour la mesure de la densite electronique d'un gas ionise. Elle n'est ni exhaustive, ni complete. Pour plus de details on voudra bien se rapporter aux travaux mentionnes. La premiere partie consacree a des rappels theoriques, concerne la propagation des ondes electromagnetiques dans les milieux ionises et sur l'excitation d'ondes stationnaires dans les cavites electromagnetiques. La seconde se rapporte aux techniques de mesures proprement dites. On a fait figurer dans cette partie des techniques devenues classiques et celles plus recentes en cours d'etudes dans divers laboratoires et au Service de Physique Appliquee a SACLAY. (auteur)

  6. Boron doping a semiconductor particle

    Science.gov (United States)

    Stevens, Gary Don; Reynolds, Jeffrey Scott; Brown, Louanne Kay

    1998-06-09

    A method (10,30) of boron doping a semiconductor particle using boric acid to obtain a p-type doped particle. Either silicon spheres or silicon powder is mixed with a diluted solution of boric acid having a predetermined concentration. The spheres are dried (16), with the boron film then being driven (18) into the sphere. A melt procedure mixes the driven boron uniformly throughout the sphere. In the case of silicon powder, the powder is metered out (38) into piles and melted/fused (40) with an optical furnace. Both processes obtain a p-type doped silicon sphere with desired resistivity. Boric acid is not a restricted chemical, is inexpensive, and does not pose any special shipping, handling, or disposal requirements.

  7. Fuzzy Logic Application in Boron and Cadmium Analysis in U3O8 use of Emission Spectrograph Method

    Directory of Open Access Journals (Sweden)

    S. Simbolon

    2011-04-01

    Full Text Available Boron and cadmium in U3O8 have been analyzed with emission spectrograph. Three inputs of emission spectrograph, current (A, exposure time (second and gap between electrodes (mm were varied. Two outputs, boron and cadmium lines intensities respectively were selected and measured. Thirteen experiments have been carried out and data found were calculated by fuzzy logic Mamdani-type. Three and five memberships functions of straight-line (Triangular, Trapezoidal, Generalized-bell and Gaussian curve were used to analyze the found data. The result found that five memberships functions had less error percentage range than three memberships functions of straight-line (Triangular, Trapezoidal, Generalized-bell and Gaussian curve. The error percentage range of cadmium analysis was wider than boron analysis with this method. Analysis of cadmium in U3O8 with this method needs much exposure time compare to analysis of boron

  8. Liposomal bortezomib nanoparticles via boronic ester prodrug formulation for improved therapeutic efficacy in vivo.

    Science.gov (United States)

    Ashley, Jonathan D; Stefanick, Jared F; Schroeder, Valerie A; Suckow, Mark A; Kiziltepe, Tanyel; Bilgicer, Basar

    2014-06-26

    In this study, we describe the development of liposomal bortezomib nanoparticles, which was accomplished by synthesizing bortezomib prodrugs with reversible boronic ester bonds and then incorporating the resulting prodrugs into the nanoparticles via surface conjugation. Initially, several prodrug candidates were screened based upon boronic ester stability using isobutylboronic acid as a model boronic acid compound. The two most stable candidates were then selected to create surface conjugated bortezomib prodrugs on the liposomes. Our strategy yielded stable liposomal bortezomib nanoparticles with a narrow size range of 100 nm and with high reproducibility. These liposomal bortezomib nanoparticles demonstrated significant proteasome inhibition and cytotoxicity against multiple myeloma cell lines in vitro and remarkable tumor growth inhibition with reduced systemic toxicity compared to free bortezomib in vivo. Taken together, this study demonstrates the incorporation of bortezomib into liposomal nanoparticles via reversible boronic ester bond formation to enhance the therapeutic index for improved patient outcome.

  9. The ionised X-ray outflowing torus in ESO 323-G77: low-ionisation clumps confined by homogeneous warm absorbers

    CERN Document Server

    Sanfrutos, Mario; Krongold, Yair; Agís-González, Beatriz; Longinotti, Anna Lia

    2015-01-01

    We report on the long- and short-term X-ray spectral analysis of the polar-scattered Seyfert 1.2 galaxy ESO 323-G77, observed in three epochs between 2006 and 2013 with Chandra and XMM-Newton. Four high-resolution Chandra observations give us a unique opportunity to study the properties of the absorbers in detail, as well as their short time-scale (days) variability. From the rich set of absorption features seen in the Chandra data, we identify two warm absorbers with column densities and ionisations that are consistent with being constant on both short and long time-scales, suggesting that those are the signature of a rather homogeneous and extended outflow. A third absorber, ionised to a lesser degree, is also present and it replaces the strictly neutral absorber that is ubiquitously inferred from the X-ray analysis of obscured Compton-thin sources. This colder absorber appears to vary in column density on long time-scales, suggesting a non-homogeneous absorber. Moreover, its ionisation responds to the nucl...

  10. Thermal conductivity of boron carbides

    Science.gov (United States)

    Wood, C.; Emin, D.; Gray, P. E.

    1985-01-01

    Knowledge of the thermal conductivity of boron carbide is necessary to evaluate its potential for high-temperature thermoelectric energy conversion applications. Measurements have been conducted of the thermal diffusivity of hot-pressed boron carbide BxC samples as a function of composition (x in the range from 4 to 9), temperature (300-1700 K), and temperature cycling. These data, in concert with density and specific-heat data, yield the thermal conductivities of these materials. The results are discussed in terms of a structural model that has been previously advanced to explain the electronic transport data. Some novel mechanisms for thermal conduction are briefly discussed.

  11. Evaluation of Aluminum-Boron Carbide Neutron Absorbing Materials for Interim Storage of Used Nuclear Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lumin [Univ. of Michigan, Ann Arbor, MI (United States). Department of Nuclear Engineering and Radiological Science; Wierschke, Jonathan Brett [Univ. of Michigan, Ann Arbor, MI (United States). Department of Nuclear Engineering and Radiological Science

    2015-04-08

    The objective of this work was to understand the corrosion behavior of Boral® and Bortec® neutron absorbers over long-term deployment in a used nuclear fuel dry cask storage environment. Corrosion effects were accelerated by flowing humidified argon through an autoclave at temperatures up to 570°C. Test results show little corrosion of the aluminum matrix but that boron is leaching out of the samples. Initial tests performed at 400 and 570°C were hampered by reduced flow caused by the rapid build-up of solid deposits in the outlet lines. Analysis of the deposits by XRD shows that the deposits are comprised of boron trioxide and sassolite (H3BO3). The collection of boron- containing compounds in the outlet lines indicated that boron was being released from the samples. Observation of the exposed samples using SEM and optical microscopy show the growth of new phases in the samples. These phases were most prominent in Bortec® samples exposed at 570°C. Samples of Boral® exposed at 570°C showed minimal new phase formation but showed nearly the complete loss of boron carbide particles. Boron carbide loss was also significant in Boral samples at 400°C. However, at 400°C phases similar to those found in Bortec® were observed. The rapid loss of the boron carbide particles in the Boral® is suspected to inhibit the formation of the new secondary phases. However, Material samples in an actual dry cask environment would be exposed to temperatures closer to 300°C and less water than the lowest test. The results from this study conclude that at the temperature and humidity levels present in a dry cask environment, corrosion and boron leaching will have no effect on the performance of Boral® and Bortec® to maintain criticality control.

  12. Boron Nitride Nanoribbons from Exfoliation of Boron Nitride Nanotubes

    Science.gov (United States)

    Hung, Ching-Cheh; Hurst, Janet; Santiago, Diana

    2017-01-01

    Two types of boron nitride nanotubes (BNNTs) were exfoliated into boron nitride nanoribbons (BNNR), which were identified using transmission electron microscopy: (1) commercial BNNTs with thin tube walls and small diameters. Tube unzipping was indicated by a large decrease of the sample's surface area and volume for pores less than 2 nm in diameter. (2) BNNTs with large diameters and thick walls synthesized at NASA Glenn Research Center. Here, tube unraveling was indicated by a large increase in external surface area and pore volume. For both, the exfoliation process was similar to the previous reported method to exfoliate commercial hexagonal boron nitride (hBN): Mixtures of BNNT, FeCl3, and NaF (or KF) were sequentially treated in 250 to 350 C nitrogen for intercalation, 500 to 750 C air for exfoliation, and finally HCl for purification. Property changes of the nanosized boron nitride throughout this process were also similar to the previously observed changes of commercial hBN during the exfoliation process: Both crystal structure (x-ray diffraction data) and chemical properties (Fourier-transform infrared spectroscopy data) of the original reactant changed after intercalation and exfoliation, but most (not all) of these changes revert back to those of the reactant once the final, purified products are obtained.

  13. Computational Studies of Nanostructures of Boron

    Science.gov (United States)

    Tandy, P.; Yu, M.; Leahy, C.; Tian, W. Q.; Wu, S. Y.; Jayanthi, C. S.

    2009-03-01

    The goal of this work is to develop a reliable semi-empirical Hamiltonian for boron that may be used to predict nanostructures of boron. It is well known that bonding in boron is complicated as it may form three-center, two-electron bonds. The semi-empirical Hamiltonian used here was recently developed by Leahy et al. in the framework of linear combination of atomic orbitals[1]. The salient feature of this Hamiltonian is that it treats environment dependency and charge redistributions on equal footing. It will be shown that such a parameterized Hamiltonian can predict the B80 cage structure with C1 symmetry as found in a recent first-principles study [2]. Having validated our semi-empirical Hamiltonian for boron with small boron clusters and the B80 cage, we have performed a systematic study of other boron nanostructures: (i) larger cage structures (e.g., B215), (ii) boron clusters cut from the bulk alpha boron, and (iii) boron sheets (triangular sheets with and without holes). We will discuss the ground state structures of these boron nanostructures as well as the energetics and HOMO-LUMO gaps of different families of boron clusters as a function their diameters. 1. C. Leahy et al. Phys. Rev. B74, 155408 (2006). 2. N. G. Szwacki et al. PRL 100, 159901 (2008).

  14. For discussion: obtaining consent for ionising radiation: has the time come?

    Science.gov (United States)

    Mendelson, Richard M

    2010-10-01

    The aim of this paper is to promote debate on the issues surrounding the provision of information to, and the obtaining of valid consent from patients exposed to ionising radiation (IR) from diagnostic and interventional imaging procedures. This is especially pertinent in view of recent interest in the risks of IR expressed in the medical and lay press.

  15. Examining Pre-Service Teachers' Use of Atomic Models in Explaining Subsequent Ionisation Energy Values

    Science.gov (United States)

    Wheeldon, Ruth

    2012-01-01

    Chemistry students' explanations of ionisation energy phenomena often involve a number of non-scientific or inappropriate ideas being used to form causality arguments. Research has attributed this to many science teachers using these ideas themselves (Tan and Taber, in "J Chem Educ" 86(5):623-629, 2009). This research extends this work by…

  16. Calculated ionisation potentials to determine the oxidation of vanillin precursors by lignin peroxidase.

    NARCIS (Netherlands)

    Have, ten R.; Rietjens, I.M.C.M.; Hartmans, S.; Swarts, H.J.; Field, J.A.

    1998-01-01

    In view of the biocatalytic production of vanillin, this research focused on the lignin peroxidase (LiP) catalysed oxidation of naturally occurring phenolic derivatives: O-methyl ethers, O-acetyl esters, and O-glucosyl ethers. The ionisation potential (IP) of a series of model compounds was

  17. Time dependent non-LTE calculations of ionisation in the early universe

    CERN Document Server

    Wehrse, R; Davé, R; Dav\\'e, Romeel

    2005-01-01

    We present a new implicit numerical algorithm for the calculation of the time dependent non-Local Thermodynamic Equilibrium of a gas in an external radiation field that is accurate, fast and unconditionally stable for all spatial and temporal increments. The method is presented as a backward difference scheme in 1-D but can be readily generalised to 3-D. We apply the method for calculating the evolution of ionisation domains in a hydrogen plasma with plane-parallel Gaussian density enhancements illuminated by sources of UV radiation. We calculate the speed of propagation of ionising fronts through different ambient densities and the interaction of such ionising fronts with density enhancements. We show that for a typical UV source that may be present in the early universe, the introduction of a density enhancement of a factor ~10 above an ambient density 10^{-4} atoms/cm^3 could delay the outward propagation of an ionisation front by millions of years. Our calculations show that within the lifetime of a singl...

  18. The impact of high and low dose ionising radiation on the central nervous system

    Directory of Open Access Journals (Sweden)

    Calina Betlazar

    2016-10-01

    Full Text Available Responses of the central nervous system (CNS to stressors and injuries, such as ionising radiation, are modulated by the concomitant responses of the brains innate immune effector cells, microglia. Exposure to high doses of ionising radiation in brain tissue leads to the expression and release of biochemical mediators of ‘neuroinflammation’, such as pro-inflammatory cytokines and reactive oxygen species (ROS, leading to tissue destruction. Contrastingly, low dose ionising radiation may reduce vulnerability to subsequent exposure of ionising radiation, largely through the stimulation of adaptive responses, such as antioxidant defences. These disparate responses may be reflective of non-linear differential microglial activation at low and high doses, manifesting as an anti-inflammatory or pro-inflammatory functional state. Biomarkers of pathology in the brain, such as the mitochondrial Translocator Protein 18 kDa (TSPO, have facilitated in vivo characterisation of microglial activation and ‘neuroinflammation’ in many pathological states of the CNS, though the exact function of TSPO in these responses remains elusive. Based on the known responsiveness of TSPO expression to a wide range of noxious stimuli, we discuss TSPO as a potential biomarker of radiation-induced effects.

  19. Calculated ionisation potentials to determine the oxidation of vanillin precursors by lignin peroxidase.

    NARCIS (Netherlands)

    ten Have, R.; Rietjens, I.M.C.M.; Hartmans, S.; Swarts, H.J.; Field, J.A.

    1998-01-01

    In view of the biocatalytic production of vanillin, this research focused on the lignin peroxidase (LiP) catalysed oxidation of naturally occurring phenolic derivatives: O-methyl ethers, O-acetyl esters, and O-glucosyl ethers. The ionisation potential (IP) of a series of model compounds was calculat

  20. Resolving Ionisation and Metallicity on Parsec Scales Across Mrk 71 (NGC2363) with HST-WFC3

    CERN Document Server

    James, Bethan L; Aloisi, Alessandra; Calzetti, Daniela; Kewley, Lisa

    2015-01-01

    Blue Compact Dwarf (BCD) Galaxies in the nearby Universe provide a means for studying feedback mechanisms and star-formation processes in low-metallicity environments in great detail. Due to their vicinity, these local analogues to young galaxies are well suited for high-resolution studies that would be unfeasible for primordial galaxies in the high-redshift universe. Here we present HST-WFC3 observations of one such BCD, Mrk 71 (NGC 2363), one of the most powerful local starbursts known, in the light of [O II], He II, Hb, [O III], Ha, and [S II]. At D=3.44 Mpc, this extensive suite of emission line images enables us to explore the chemical and physical conditions of Mrk 71 on ~2 pc scales. Using these high spatial-resolution observations, we use emission line diagnostics to distinguish ionisation mechanisms on a pixel-by-pixel basis and show that despite the previously reported hypersonic gas and super-bubble blow out, the gas in Mrk 71 is photoionised, with no sign of shock-excited emission. Using strong-li...

  1. Advanced microstructure of boron carbide.

    Science.gov (United States)

    Werheit, Helmut; Shalamberidze, Sulkhan

    2012-09-26

    The rhombohedral elementary cell of the complex boron carbide structure is composed of B(12) or B(11)C icosahedra and CBC, CBB or B□B (□, vacancy) linear arrangements, whose shares vary depending on the actual chemical compound. The evaluation of the IR phonon spectra of isotopically pure boron carbide yields the quantitative concentrations of these components within the homogeneity range. The structure formula of B(4.3)C at the carbon-rich limit of the homogeneity range is (B(11)C) (CBC)(0.91) (B□B)(0.09) (□, vacancy); and the actual structure formula of B(13)C(2) is (B(12))(0.5)(B(11)C)(0.5)(CBC)(0.65)(CBB)(0.16) (B□B)(0.19), and deviates fundamentally from (B(12))CBC, predicted by theory to be the energetically most favourable structure of boron carbide. In reality, it is the most distorted structure in the homogeneity range. The spectra of (nat)B(x)C make it evident that boron isotopes are not randomly distributed in the structure. However, doping with 2% silicon brings about a random distribution.

  2. Destruction of Raman biosignatures by ionising radiation and the implications for life detection on Mars.

    Science.gov (United States)

    Dartnell, Lewis R; Page, Kristian; Jorge-Villar, Susana E; Wright, Gary; Munshi, Tasnim; Scowen, Ian J; Ward, John M; Edwards, Howell G M

    2012-04-01

    Raman spectroscopy has proven to be a very effective approach for the detection of microorganisms colonising hostile environments on Earth. The ExoMars rover, due for launch in 2018, will carry a Raman laser spectrometer to analyse samples of the martian subsurface collected by the probe's 2-m drill in a search for similar biosignatures. The martian surface is unprotected from the flux of cosmic rays, an ionising radiation field that will degrade organic molecules and so diminish and distort the detectable Raman signature of potential martian microbial life. This study employs Raman spectroscopy to analyse samples of two model organisms, the cyanobacterium Synechocystis sp. PCC 6803 and the extremely radiation resistant polyextremophile Deinococcus radiodurans, that have been exposed to increasing doses of ionising radiation. The three most prominent peaks in the Raman spectra are from cellular carotenoids: deinoxanthin in D. radiodurans and β-carotene in Synechocystis. The degradative effect of ionising radiation is clearly seen, with significant diminishment of carotenoid spectral peak heights after 15 kGy and complete erasure of Raman biosignatures by 150 kGy of ionising radiation. The Raman signal of carotenoid in D. radiodurans diminishes more rapidly than that of Synechocystis, believed to be due to deinoxanthin acting as a superior scavenger of radiolytically produced reactive oxygen species, and so being destroyed more quickly than the less efficient antioxidant β-carotene. This study highlights the necessity for further experimental work on the manner and rate of degradation of Raman biosignatures by ionising radiation, as this is of prime importance for the successful detection of microbial life in the martian near subsurface.

  3. Friction anisotropy in boronated graphite

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, N., E-mail: niranjan@igcar.gov.in [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Radhika, R. [Crystal Growth Centre, Anna University, Chennai (India); Kozakov, A.T. [Research Institute of Physics, Southern Federal University, Rostov-on-Don (Russian Federation); Pandian, R. [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Chakravarty, S. [UGC-DAE CSR, Kalpakkam (India); Ravindran, T.R.; Dash, S.; Tyagi, A.K. [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    2015-01-01

    Graphical abstract: - Highlights: • Friction anisotropy in boronated graphite is observed in macroscopic sliding condition. • Low friction coefficient is observed in basal plane and becomes high in prismatic direction. • 3D phase of boronated graphite transformed into 2D structure after friction test. • Chemical activity is high in prismatic plane forming strong bonds between the sliding interfaces. - Abstract: Anisotropic friction behavior in macroscopic scale was observed in boronated graphite. Depending upon sliding speed and normal loads, this value was found to be in the range 0.1–0.35 in the direction of basal plane and becomes high 0.2–0.8 in prismatic face. Grazing-incidence X-ray diffraction analysis shows prominent reflection of (0 0 2) plane at basal and prismatic directions of boronated graphite. However, in both the wear tracks (1 1 0) plane become prominent and this transformation is induced by frictional energy. The structural transformation in wear tracks is supported by micro-Raman analysis which revealed that 3D phase of boronated graphite converted into a disordered 2D lattice structure. Thus, the structural aspect of disorder is similar in both the wear tracks and graphite transfer layers. Therefore, the crystallographic aspect is not adequate to explain anisotropic friction behavior. Results of X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy shows weak signature of oxygen complexes and functional groups in wear track of basal plane while these species dominate in prismatic direction. Abundance of these functional groups in prismatic plane indicates availability of chemically active sites tends to forming strong bonds between the sliding interfaces which eventually increases friction coefficient.

  4. Boron-10 ABUNCL Prototype Models And Initial Active Testing

    Energy Technology Data Exchange (ETDEWEB)

    Kouzes, Richard T.; Ely, James H.; Lintereur, Azaree T.; Siciliano, Edward R.

    2013-04-23

    The Department of Energy Office of Nuclear Safeguards and Security (NA-241) is supporting the project Coincidence Counting With Boron-Based Alternative Neutron Detection Technology at Pacific Northwest National Laboratory (PNNL) for the development of a 3He proportional counter alternative neutron coincidence counter. The goal of this project is to design, build and demonstrate a system based upon 10B-lined proportional tubes in a configuration typical for 3He-based coincidence counter applications. This report provides results from MCNPX model simulations and initial testing of the active mode variation of the Alternative Boron-Based Uranium Neutron Coincidence Collar (ABUNCL) design built by General Electric Reuter-Stokes. Initial experimental testing of the as-delivered passive ABUNCL was previously reported.

  5. Synthesis and biological activity of peptide proline-boronic acids as proteasome inhibitors.

    Science.gov (United States)

    Han, Liqiang; Wen, Yanzhao; Li, Ridong; Xu, Bo; Ge, Zemei; Wang, Xin; Cheng, Tieming; Cui, Jingrong; Li, Runtao

    2017-08-01

    On the basis of the application of proline-boronic acid as pharmacophore in the kinase inhibitors and our previous research results, using proline-boronic acid as warhead, two series of peptide proline-boronic acids, dipeptide proline-boronic acids (I) and tripeptide proline-boronic acids (II), were designed and synthesized. All the synthesized compounds were first evaluated for their biological activity against MGC803 cell, and then, the best compound II-7 was selected to test its anti-tumor spectrum on six human tumor cell lines and proteasome inhibition against three subunits. The results indicated that series II have much better biological activities than series I. The compound II-7 exhibited not only excellent biological activities with IC50 values of nM level in both cell and proteasome models, but also much better subunit selectivity. Thus, proline-boronic acid as warhead is reasonable in the design of proteasome inhibitors. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Jaguar Procedures for Detonation Behavior of Explosives Containing Boron

    Science.gov (United States)

    Stiel, L. I.; Baker, E. L.; Capellos, C.

    2009-12-01

    The Jaguar product library was expanded to include boron and boron containing products by analysis of Available Hugoniot and static volumetric data to obtain constants of the Murnaghan relationships for the components. Experimental melting points were also utilized to obtain the constants of the volumetric relationships for liquid boron and boron oxide. Detonation velocities for HMX—boron mixtures calculated with these relationships using Jaguar are in closer agreement with literature values at high initial densities for inert (unreacted) boron than with the completely reacted metal. These results indicate that the boron does not react near the detonation front or that boron mixtures exhibit eigenvalue detonation behavior (as shown by some aluminized explosives), with higher detonation velocities at the initial points. Analyses of calorimetric measurements for RDX—boron mixtures indicate that at high boron contents the formation of side products, including boron nitride and boron carbide, inhibits the detonation properties of the formulation.

  7. Synthesis of Boron Nanowires, Nanotubes, and Nanosheets

    Directory of Open Access Journals (Sweden)

    Rajen B. Patel

    2015-01-01

    Full Text Available The synthesis of boron nanowires, nanotubes, and nanosheets using a thermal vapor deposition process is reported. This work confirms previous research and provides a new method capable of synthesizing boron nanomaterials. The materials were made by using various combinations of MgB2, Mg(BH42, MCM-41, NiB, and Fe wire. Unlike previously reported methods, a nanoparticle catalyst and a silicate substrate are not required for synthesis. Two types of boron nanowires, boron nanotubes, and boron nanosheets were made. Their morphology and chemical composition were determined through the use of scanning electron microscopy, transmission electron microscopy, and electron energy loss spectroscopy. These boron-based materials have potential for electronic and hydrogen storage applications.

  8. Prediction of boron carbon nitrogen phase diagram

    Science.gov (United States)

    Yao, Sanxi; Zhang, Hantao; Widom, Michael

    We studied the phase diagram of boron, carbon and nitrogen, including the boron-carbon and boron-nitrogen binaries and the boron-carbon-nitrogen ternary. Based on the idea of electron counting and using a technique of mixing similar primitive cells, we constructed many ''electron precise'' structures. First principles calculation is performed on these structures, with either zero or high pressures. For the BN binary, our calculation confirms that a rhmobohedral phase can be stablized at high pressure, consistent with some experimental results. For the BCN ternary, a new ground state structure is discovered and an Ising-like phase transition is suggested. Moreover, we modeled BCN ternary phase diagram and show continuous solubility from boron carbide to the boron subnitride phase.

  9. On-line neutron beam monitoring of the Finnish BNCT facility

    Science.gov (United States)

    Tanner, Vesa; Auterinen, Iiro; Helin, Jori; Kosunen, Antti; Savolainen, Sauli

    1999-02-01

    A Boron Neutron Capture Therapy (BNCT) facility has been built at the FiR 1 research reactor of VTT Chemical Technology in Espoo, Finland. The facility is currently undergoing dosimetry characterisation and neutron beam operation research for clinical trials. The healthy tissue tolerance study, which was carried out in the new facility during spring 1998, demonstrated the reliability and user-friendliness of the new on-line beam monitoring system designed and constructed for BNCT by VTT Chemical Technology. The epithermal neutron beam is monitored at a bismuth gamma shield after an aluminiumfluoride-aluminium moderator. The detectors are three pulse mode U 235-fission chambers for epithermal neutron fluence rate and one current mode ionisation chamber for gamma dose rate. By using different detector sensitivities the beam intensity can be measured over a wide range of reactor power levels (0.001-250 kW). The detector signals are monitored on-line with a virtual instrumentation (LabView) based PC-program, which records and displays the actual count rates and total counts of the detectors in the beam. Also reactor in-core power instrumentation and control rod positions can be monitored via another LabView application. The main purpose of the monitoring system is to provide a dosimetric link to the dose in a patient during the treatment, as the fission chamber count rates have been calibrated to the induced thermal neutron fluence rate and to the absorbed dose rate at reference conditions in a tissue substitute phantom.

  10. Composite Reinforcement using Boron Nitride Nanotubes

    Science.gov (United States)

    2014-05-09

    Final 3. DATES COVERED (From - To) 11-Mar-2013 to 10-Mar-2014 4. TITLE AND SUBTITLE Composite Reinforcement using Boron Nitride Nanotubes...AVAILABILITY STATEMENT Approved for public release. 13. SUPPLEMENTARY NOTES 14. ABSTRACT Boron nitride nanotubes have been proposed as a...and titanium (Ti) metal clusters with boron nitride nanotubes (BNNT). First-principles density-functional theory plus dispersion (DFT-D) calculations

  11. Oxygen radical functionalization of boron nitride nanosheets

    OpenAIRE

    MAY, PETER; Coleman, Jonathan; MCGOVERN, IGNATIUS; GOUNKO, IOURI; Satti, Amro

    2012-01-01

    PUBLISHED The covalent chemical functionalization of exfoliated hexagonal boron-nitride nanosheets (BNNSs) is achieved by the solution phase oxygen radical functionalization of boron atoms in the h-BN lattice. This involves a two-step procedure to initially covalently graft alkoxy groups to boron atoms and the subsequent hydrolytic defunctionalisation of the groups to yield hydroxyl-functionalized BNNSs (OH-BNNSs). Characterization of the functionalized-BNNSs using HR-TEM, Raman, UV-Vis, F...

  12. Magnetorotational instability in weakly ionised, stratified accretion discs

    CERN Document Server

    Salmeron, Roberto Aureliano; Salmeron, Raquel; Wardle, Mark

    2003-01-01

    The magnetorotational instability (MRI) (Balbus and Hawley 1991, Hawley and Balbus 1991) transports angular momentum radially outwards in accretion discs through the distortion of the magnetic field lines that connect fluid elements. In protostellar discs, low conductivity is important, especially in the inner regions (Gammie 1996, Wardle 1997). As a result, low k modes are relevant and vertical stratification is a key factor of the analysis. However, most models of the MRI in these environments have adopted either the ambipolar diffusion or resistive approximations and have not simultaneously treated stratification and Hall conductivity. We present here a linear analysis of the MRI, including the Hall effect, in a stratified disc.

  13. Mineral resource of the month: boron

    Science.gov (United States)

    Crangle, Robert D.

    2012-01-01

    The article offers information on the mineral, boron. Boron compounds, particularly borates, have more commercial applications than its elemental relative which is a metalloid. Making up the 90% of the borates that are used worldwide are colemanite, kernite, tincal, and ulexite. The main borate deposits are located in the Mojave Desert of the U.S., the Tethyan belt in southern Asia, and the Andean belt of South America. Underground and surface mining are being used in gathering boron compounds. INSETS: Fun facts;Boron production and consumption.

  14. Boron deposition from fused salts. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.L.

    1980-08-01

    A partial evaluation of the feasibility of a process to electrodeposit pure coherent coatings of elemental boron from molten fluorides has been performed. The deposit produced was powdery and acicular, unless the fluoride melt was purified to have very low oxygen concentration. When the oxygen activity was reduced in the melt by addition of crystalline elemental boron, dense, amorphous boron deposit was produced. The boron deposits produced had cracks but were otherwise pure and dense and ranged up to 0.35 mm thick. Information derived during this project suggests that similar deposits might be obtained crack-free up to 1.00 mm thick by process modifications and improvements.

  15. Boron removal from geothermal waters by electrocoagulation

    Energy Technology Data Exchange (ETDEWEB)

    Yilmaz, A. Erdem [Atatuerk University, Faculty of Engineering, Department of Environmental Engineering., 25240 Erzurum (Turkey)], E-mail: aerdemy@atauni.edu.tr; Boncukcuoglu, Recep [Atatuerk University, Faculty of Engineering, Department of Environmental Engineering., 25240 Erzurum (Turkey); Kocakerim, M. Muhtar [Atatuerk University, Faculty of Engineering, Department of Chemical Engineering, 25240 Erzurum (Turkey); Yilmaz, M. Tolga; Paluluoglu, Cihan [Atatuerk University, Faculty of Engineering, Department of Environmental Engineering., 25240 Erzurum (Turkey)

    2008-05-01

    Most of the geothermal waters in Turkey contain extremely high concentration of boron when they are used for irrigation. The use of geothermal waters for irrigation can results in excess amount deposition of boron in soil. On the other hand, a minimal boron concentration is required for irrigational waters. In this study, electrocoagulation (EC) was selected as a treatment process for the removal of boron from thermal waters obtained from Ilica-Erzurum in Turkey. Current density (CD), pH of solution and temperature of solution were selected as operational parameters. The results showed that boron removal efficiency increased from pH 4.0 to 8.0 and decreased at pH 10.0. Although boron removal efficiency was highest at pH 8.0, energy consumption was very high at this pH value compared to other pH intervals. Boron removal efficiency reached to 95% with increasing current density from 1.5 to 6.0 mA/cm{sup 2}, but energy consumption was also increased in this interval. At higher temperatures of solution, such as 313 and 333 K, boron removal efficiency increased. At optimum conditions, boron removal efficiency in geothermal water reached up to 95%.

  16. Conduction mechanism in boron carbide

    Science.gov (United States)

    Wood, C.; Emin, D.

    1984-01-01

    Electrical conductivity, Seebeck-coefficient, and Hall-effect measurements have been made on single-phase boron carbides, B(1-x)C(x), in the compositional range from 0.1 to 0.2 X, and between room temperature and 1273 K. The results indicate that the predominant conduction mechanism is small-polaron hopping between carbon atoms at geometrically inequivalent sites.

  17. Boron Isotopes in Benthic Foraminifera by MC-ICPMS: Unlocking the Ocean's Carbon Cycle

    Science.gov (United States)

    Rae, J. W.; Foster, G. L.; Schmidt, D. N.; Elliott, T. R.

    2008-12-01

    The cause of glacial-interglacial CO2 cycles has been described as the "holy grail" of climate science. All models currently proposed invoke changes in deep ocean carbon storage, but the mechanisms by which this took place remain unclear. Proxies for two components of the ocean carbonate system would allow us to fully reconstruct ocean carbonate equilibria and trace the spatial and temporal pattern of glacial carbon storage, providing valuable constraints on the causal mechanisms of atmospheric CO2 change. The theory behind the boron isotope pH proxy is well understood, but its reliability has been questioned, primarily due to uncertainty in the fractionation factor between boron species in seawater, and analytical difficulties associated with negative thermal ionisation (NTIMS) measurements. We have developed a new technique for boron isotopic analysis by multicollector inductively coupled plasma mass spectrometry (MC- ICPMS), which overcomes many of the problems associated with NTIMS measurements. Our method is precise (better than 0.25%, or ~0.02 pH units, on full procedural replicates at 95% confidence), rapid (allowing duplicate measurement of 10-20 samples per analytical session), and has small sample size requirements of ~10 ng boron (~0.5 mg foraminiferal tests). As MC-ICPMS analysis requires separation of boron prior to measurement, any bias between samples and standards with different matrices is also removed. Recent experimental work has also improved uncertainty in the isotopic fractionation factor (now measured at 1.0272 ±0.0006 [1]), providing a powerful independent means to test the behaviour of the foram-based δ11B proxy, and its ability to provide absolute pH values. We have measured δ11B in several species of benthic foraminifera from a range of core-top samples. In contrast to previous studies, we find a very close match between foraminiferal δ11B values and the δ11B of seawater B(OH)4- - predicted using the recently determined fractionation

  18. How do air ions reflect variations in ionising radiation in the lower atmosphere in a boreal forest?

    Science.gov (United States)

    Chen, Xuemeng; Kerminen, Veli-Matti; Paatero, Jussi; Paasonen, Pauli; Manninen, Hanna E.; Nieminen, Tuomo; Petäjä, Tuukka; Kulmala, Markku

    2016-11-01

    Most of the ion production in the atmosphere is attributed to ionising radiation. In the lower atmosphere, ionising radiation consists mainly of the decay emissions of radon and its progeny, gamma radiation of the terrestrial origin as well as photons and elementary particles of cosmic radiation. These types of radiation produce ion pairs via the ionisation of nitrogen and oxygen as well as trace species in the atmosphere, the rate of which is defined as the ionising capacity. Larger air ions are produced out of the initial charge carriers by processes such as clustering or attachment to pre-existing aerosol particles. This study aimed (1) to identify the key factors responsible for the variability in ionising radiation and in the observed air ion concentrations, (2) to reveal the linkage between them and (3) to provide an in-depth analysis into the effects of ionising radiation on air ion formation, based on measurement data collected during 2003-2006 from a boreal forest site in southern Finland. In general, gamma radiation dominated the ion production in the lower atmosphere. Variations in the ionising capacity came from mixing layer dynamics, soil type and moisture content, meteorological conditions, long-distance transportation, snow cover attenuation and precipitation. Slightly similar diurnal patterns to variations in the ionising capacity were observed in air ion concentrations of the cluster size (0.8-1.7 nm in mobility diameters). However, features observed in the 0.8-1 nm ion concentration were in good connection to variations of the ionising capacity. Further, by carefully constraining perturbing variables, a strong dependency of the cluster ion concentration on the ionising capacity was identified, proving the functionality of ionising radiation in air ion production in the lower atmosphere. This relationship, however, was only clearly observed on new particle formation (NPF) days, possibly indicating that charges after being born underwent different

  19. Exploring the Powerful Ionised Wind in the Seyfert Galaxy PG1211+143

    Science.gov (United States)

    Pounds, Ken

    2013-10-01

    Highly-ionised high-speed winds in AGN (UFOs) were first detected with XMM-Newton a decade ago, and are now established as a key factor in the study of SMBH accretion, and in the growth and metal enrichment of their host galaxies. However, information on the ionisation and dynamical structure, and the ultimate fate of UFOs remains very limited. We request a 600ks extended XMM-Newton study of the prototype UFO PG1211+143 in AO-13, to obtain high quality EPIC and RGS spectra, to map the flow structure and variability, while seeking evidence for the anticipated interaction with the ISM and possible conversion of the energetic wind to a momentum-driven flow.

  20. Constraints on ionising photon production from the large-scale Lyman-alpha forest

    CERN Document Server

    Pontzen, Andrew; Peiris, Hiranya; Verde, Licia

    2014-01-01

    Recent work has shown that the z~2.5 Lyman-alpha forest on large scales encodes information about the galaxy and quasar populations that keep the intergalactic medium photoionized. We present the first forecasts for constraining the populations with data from current and next-generation surveys. At a minimum the forest should tell us whether galaxies or, conversely, quasars dominate the photon production. The number density and clustering strength of the ionising sources might be estimated to sub-10% precision with a DESI-like survey if degeneracies (e.g., with the photon mean-free-path, small-scale clustering power normalization and potentially other astrophysical effects) can be broken by prior information. We demonstrate that, when inhomogeneous ionisation is correctly handled, constraints on dark energy do not degrade.

  1. The effect of highly ionising particles on the CMS silicon strip tracker

    CERN Document Server

    Adam, W; Bergauer, T; Bouhali, O; Clerbaux, B; De Langhe, E; De Lentdecker, G; De Wolf, E; Friedl, M; Frühwirth, R; Hrubec, Josef; Krammer, Manfred; Pernicka, Manfred; Tasevsky, M; Waltenberger, W

    2005-01-01

    Inelastic nuclear collisions of hadrons incident on silicon sensors can generate secondary highly ionising particles (HIPs) and deposit as much energy within the sensor bulk as several hundred minimum ionising particles. The large signals generated by these 'HIP events' can momentarily saturate the APV25 front-end readout chip for the silicon strip tracker (SST) sub-detector of the compact muon solenoid (CMS) experiment, resulting in deadtime in the detector readout system. This paper presents studies of this phenomenon through simulation, laboratory measurements and dedicated beam tests. A proposed change to a front-end component to reduce the APV25 sensitivity to HIP events is also examined. The results are used to infer the expected effect on the performance of the CMS SST at the future large hadron collider. The induced inefficiencies are at the percent level and will have a negligible effect on the physics performance of the SST.

  2. Ionisation and discharge in cloud-forming atmospheres of brown dwarfs and extrasolar planets

    CERN Document Server

    Helling, Ch; Rodriguez-Barrera, I M; Wood, Kenneth; Robertson, G B; Stark, C R

    2016-01-01

    Brown dwarfs and giant gas extrasolar planets have cold atmospheres with a rich chemical compositions from which mineral cloud particles form. Their properties, like particle sizes and material composition, vary with height, and the mineral cloud particles are charged due to triboelectric processes in such dynamic atmospheres. The dynamics of the atmospheric gas is driven by the irradiating host star and/or by the rotation of the objects that changes during its lifetime. Thermal gas ionisation in these ultra-cool but dense atmospheres allows electrostatic interactions and magnetic coupling of a substantial atmosphere volume. Combined with a strong magnetic field $\\gg B_{\\rm Earth}$, a chromosphere and aurorae might form as suggested by radio and X-ray observations of brown dwarfs. Non-equilibrium processes like cosmic ray ionisation and discharge processes in clouds will increase the local pool of free electrons in the gas. Cosmic rays and lighting discharges also alter the composition of the local atmospheri...

  3. Positron-impact ionisation of atomic hydrogen in the presence of a bichromatic laser field

    Institute of Scientific and Technical Information of China (English)

    Lou Jun; Li Shu-Min

    2010-01-01

    The positron impact-ionisation of atomic hydrogen in the presence of a linearly polarised bichromatic field is investigated in the first Born approximation.The field is composed of a fundamental frequency and its second harmonic.The state of positron in the field is described by the Volkov wavefunction,and the continuum state of the ejected electron is described by the Coulomb-Volkov wavefunction.The dressed ground state of target is a first order time-dependent perturbative wavefunction.The triple differential cross sections and their dependencies on laser field parameters are discussed and compared with the results modified by a monochromatic field.Numerical results show that the coherent phase control is significant and the laser-assisted ionisation cross sections caused by positron and electron are different.

  4. Characterisation of surface ionisation and adsorption of phenol and 4-nitrophenol on non-porous carbon blacks

    OpenAIRE

    Carrott, Peter; Carrott, Manuela; Vale, Tania; Valente Nabais, Joao; Mourao, Paulo

    2008-01-01

    The adsorption of phenol and 4-nitrophenol from aqueous solutions by carbon blacks was studied. Particular attention was paid to the characterisation of the surface chemistry and ionisation of the carbon blacks by use of a simple carbon surface ionisation model, as well as the use of a normalised form of the Freundlich equation for the analysis of the adsorption isotherms. The results indicated that the solutes interact directly with the graphene layers and that the adsorpti...

  5. Boron coating on boron nitride coated nuclear fuels by chemical vapor deposition

    Science.gov (United States)

    Durmazuçar, Hasan H.; Gündüz, Güngör

    2000-12-01

    Uranium dioxide-only and uranium dioxide-gadolinium oxide (5% and 10%) ceramic nuclear fuel pellets which were already coated with boron nitride were coated with thin boron layer by chemical vapor deposition to increase the burn-up efficiency of the fuel during reactor operation. Coating was accomplished from the reaction of boron trichloride with hydrogen at 1250 K in a tube furnace, and then sintering at 1400 and 1525 K. The deposited boron was identified by infrared spectrum. The morphology of the coating was studied by using scanning electron microscope. The plate, grainy and string (fiber)-like boron structures were observed.

  6. Ionisation and discharge in cloud-forming atmospheres of brown dwarfs and extrasolar planets

    Science.gov (United States)

    Helling, Ch; Rimmer, P. B.; Rodriguez-Barrera, I. M.; Wood, Kenneth; Robertson, G. B.; Stark, C. R.

    2016-07-01

    Brown dwarfs and giant gas extrasolar planets have cold atmospheres with rich chemical compositions from which mineral cloud particles form. Their properties, like particle sizes and material composition, vary with height, and the mineral cloud particles are charged due to triboelectric processes in such dynamic atmospheres. The dynamics of the atmospheric gas is driven by the irradiating host star and/or by the rotation of the objects that changes during its lifetime. Thermal gas ionisation in these ultra-cool but dense atmospheres allows electrostatic interactions and magnetic coupling of a substantial atmosphere volume. Combined with a strong magnetic field \\gg {{B}\\text{Earth}} , a chromosphere and aurorae might form as suggested by radio and x-ray observations of brown dwarfs. Non-equilibrium processes like cosmic ray ionisation and discharge processes in clouds will increase the local pool of free electrons in the gas. Cosmic rays and lighting discharges also alter the composition of the local atmospheric gas such that tracer molecules might be identified. Cosmic rays affect the atmosphere through air showers in a certain volume which was modelled with a 3D Monte Carlo radiative transfer code to be able to visualise their spacial extent. Given a certain degree of thermal ionisation of the atmospheric gas, we suggest that electron attachment to charge mineral cloud particles is too inefficient to cause an electrostatic disruption of the cloud particles. Cloud particles will therefore not be destroyed by Coulomb explosion for the local temperature in the collisional dominated brown dwarf and giant gas planet atmospheres. However, the cloud particles are destroyed electrostatically in regions with strong gas ionisation. The potential size of such cloud holes would, however, be too small and might occur too far inside the cloud to mimic the effect of, e.g. magnetic field induced star spots.

  7. Exposure of the French paediatric population to ionising radiation from diagnostic medical procedures in 2010

    Energy Technology Data Exchange (ETDEWEB)

    Etard, Cecile; Aubert, Bernard [Institut de Radioprotection et de Surete Nucleaire, Medical Expertise Unit, Fontenay-aux-Roses (France); Mezzarobba, Myriam [Institut de Radioprotection et de Surete Nucleaire, Laboratory of Epidemiology, Fontenay-aux-Roses (France); Bernier, Marie-Odile [Institut de Radioprotection et de Surete Nucleaire, Laboratory of Epidemiology, Fontenay-aux-Roses (France); Institut de Radioprotection et de Surete Nucleaire, IRSN/PRP-HOM/SRBE/LEPID, Laboratoire d' Epidemiologie, Fontenay-aux-Roses (France)

    2014-12-15

    Medical examination is the main source of artificial radiation exposure. Because children present an increased sensitivity to ionising radiation, radiology practices at a national level in paediatrics should be monitored. This study describes the ionising radiation exposure from diagnostic medical examinations of the French paediatric population in 2010. Data on frequency of examinations were provided by the French National Health Insurance through a representative sample including 107,627 children ages 0-15 years. Effective doses for each type of procedure were obtained from the published French literature. Median and mean effective doses were calculated for the studied population. About a third of the children were exposed to at least one examination using ionising radiation in 2010. Conventional radiology, dental exams, CT scans and nuclear medicine and interventional radiology represent respectively 55.3%, 42.3%, 2.1% and 0.3% of the procedures. Children 10-15 years old and babies from birth to 1 year are the most exposed populations, with respectively 1,098 and 734 examinations per 1,000 children per year. Before 1 year of age, chest and pelvis radiographs are the most common imaging tests, 54% and 32%, respectively. Only 1% of the studied population is exposed to CT scan, with 62% of these children exposed to a head-and-neck procedure. The annual median and mean effective doses were respectively 0.03 mSv and 0.7 mSv for the exposed children. This study gives updated reference data on French paediatric exposure to medical ionising radiation that can be used for public health or epidemiological purposes. Paediatric diagnostic use appears much lower than that of the whole French population as estimated in a previous study. (orig.)

  8. Ionising radiation and risk of death from leukaemia and lymphoma in radiation-monitored workers (INWORKS)

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, Bernd

    2015-07-01

    Since July 2015 the study ''ionising radiation and risk of death from leukaemia and lymphoma in radiation-monitored workers (INWORKS) - an international cohort study'' is available. INWORKS comprised data from 300.000 occupational exposed and dosimetric monitored persons from France, USA and UK. The contribution is a critical discussion of this study with respect to the conclusion of a strong evidence of positive associations between protracted low-dose irradiation exposure and leukemia.

  9. Safety Culture in activities involving ionising radiation-education project

    Energy Technology Data Exchange (ETDEWEB)

    Sahyun, A.; Sordi, G. M.; Sanches, M. P.; Levy, P. J.; Levy, D. S.

    2004-07-01

    The Brazilian National Commission of Nuclear Energy (CNEN) requires a Radiological Protection Plan for all installations authorized to work with radioactive material and a qualified Radiological Protection Supervisor. The CNEN requires the certification of practical experience in the area plus a qualification exam, applied by them. ATOMO, has opted to develop on-line courses, using multimedia resources, available at the time this congress takes place. OMICCRON, a multimedia enterprise, is in charge of the program and design. First, the research and brochures have to be adapted for the electronic language, through links, hot words and icons, especially developed for additional information. Besides the images and graphs from the original brochures, Omiccron developed, in graphic computing, specific animation explaining the procedures in more details, illustrating and simplifying the comprehension of the more complex subjects. The CD ROM presentation was enhanced with some slide displays, automatically changing the pictures, as the explanations are given. For practical visualization of these complex and important procedures, the CD also shows some technical videos. At the end of each unit covering a specific subject, the students will be submitted to self-evaluation tests, for more profitable results. This CD is not only an electronic brochure, but mainly an on-line course with weekly Internet support via e-mail or chat site, where the learners will access the instructors and a frequent questions database, useful links and related sites, permanently upgraded. Before going to the following module, the learner has to pass a written test prepared by ATOMO, via Internet. At the end of the course, a certificate will be given. The control will be made through the use of a password, provided for the authorized company and /or users. The instructors will evaluate the learners' advancement by Internet. In the case of companies, this tool will be equally offered, by using

  10. A Search for Boron in Damped Ly{\\alpha} Systems

    CERN Document Server

    Berg, Trystyn A M; Venn, Kim A; Prochaska, J Xavier

    2013-01-01

    We present the first systematic study of boron beyond the Local Group. This analysis is performed on a sample of 30 damped Ly{\\alpha} systems (DLAs) with strong metal-lines, which are expected to trace the interstellar medium of high z galaxies. We report on two boron detections at > 3{\\sigma} significance; one new detection and one confirmation. The ratios of B/O and, for the first time, B/S are compared with previous stellar and interstellar measurements in the Milky Way and Small Magellanic Cloud. The novel comparison with sulphur, which tracks oxygen's abundance, alleviates the uncertainty associated with stellar oxygen measurements. For both detections, the inferred B/S ratio is in excess of the prediction of primary boron production from spallation processes. Possible sources of contamination are discussed, as well as physical effects that could impact the observed ratios. However taken at face value, the implication of these measurements suggest potentially higher cosmic ray fluxes in DLAs. The prospec...

  11. Ambient ionisation mass spectrometry for the characterisation of polymers and polymer additives: a review.

    Science.gov (United States)

    Paine, Martin R L; Barker, Philip J; Blanksby, Stephen J

    2014-01-15

    The purpose of this review is to showcase the present capabilities of ambient sampling and ionisation technologies for the analysis of polymers and polymer additives by mass spectrometry (MS) while simultaneously highlighting their advantages and limitations in a critical fashion. To qualify as an ambient ionisation technique, the method must be able to probe the surface of solid or liquid samples while operating in an open environment, allowing a variety of sample sizes, shapes, and substrate materials to be analysed. The main sections of this review will be guided by the underlying principle governing the desorption/extraction step of the analysis; liquid extraction, laser ablation, or thermal desorption, and the major component investigated, either the polymer itself or exogenous compounds (additives and contaminants) present within or on the polymer substrate. The review will conclude by summarising some of the challenges these technologies still face and possible directions that would further enhance the utility of ambient ionisation mass spectrometry as a tool for polymer analysis.

  12. On the Ionisation Fraction in Protoplanetary Disks I: Comparing Different Reaction Networks

    CERN Document Server

    Ilgner, M; Ilgner, Martin; Richard P. Nelson

    2005-01-01

    We calculate the ionisation fraction in protostellar disk models using a number of different chemical reaction networks, including gas-phase and gas-grain reaction schemes. The disk models we consider are conventional alpha-disks, which include viscous heating and radiative cooling. The primary source of ionisation is assumed to be X-ray irradiation from the central star. We consider a number of gas-phase chemical networks. In general we find that the simple models predict higher fractional ionisation levels and more extensive active zones than the more complex models. When heavy metal atoms are included the simple models predict that the disk is magnetically active throughout. The complex models predict that extensive regions of the disk remain magnetically uncoupled even with a fractional abundance of magnesium of 10(-8). The addition of submicron sized grains with a concentration of 10(-12) causes the size of the dead zone to increase dramatically for all kinetic models considered. We find that the simple ...

  13. Field calibration studies for ionisation chambers in mixed high-energy radiation fields.

    Science.gov (United States)

    Theis, C; Forkel-Wirth, D; Fuerstner, M; Mayer, S; Otto, Th; Roesler, S; Vincke, H

    2007-01-01

    The monitoring of ambient doses at work places around high-energy accelerators is a challenging task due the complexity of the mixed stray radiation fields encountered. At CERN, mainly Centronics IG5 high-pressure ionisation chambers are used to monitor radiation exposure in mixed fields. The monitors are calibrated in the operational quantity ambient dose equivalent H*(10) using standard, source-generated photon- and neutron fields. However, the relationship between ionisation chamber reading and ambient dose equivalent in a mixed high-energy radiation field can only be assessed if the spectral response to every component and the field composition is known. Therefore, comprehensive studies were performed at the CERN-EU high-energy reference field facility where the spectral fluence for each particle type has been assessed with Monte Carlo simulations. Moreover, studies have been performed in an accessible controlled radiation area in the vicinity of a beam loss point of CERN's proton synchrotron. The comparison of measurements and calculations has shown reasonable agreement for most exposure conditions. The results indicate that conventionally calibrated ionisation chambers can give satisfactory response in terms of ambient dose equivalent in stray radiation fields at high-energy accelerators in many cases. These studies are one step towards establishing a method of 'field calibration' of radiation protection instruments in which Monte Carlo simulations will be used to establish a correct correlation between the response of specific detectors to a given high-energy radiation field.

  14. Nuclear recoil scintillation and ionisation yields in liquid xenon from ZEPLIN-III data

    CERN Document Server

    Horn, M; Akimov, D Yu; Araújo, H M; Barnes, E J; Burenkov, A A; Chepel, V; Currie, A; Edwards, B; Ghag, C; Hollingsworth, A; Kalmus, G E; Kobyakin, A S; Kovalenko, A G; Lebedenko, V N; Lindote, A; Lopes, M I; Lüscher, R; Majewski, P; Murphy, A StJ; Neves, F; Paling, S M; da Cunha, J Pinto; Preece, R; Quenby, J J; Reichhart, L; Scovell, P R; Silva, C; Solovov, V N; Smith, N J T; Smith, P F; Stekhanov, V N; Sumner, T J; Thorne, C; de Viveiros, L; Walker, R J

    2011-01-01

    Scintillation and ionisation yields for nuclear recoils in liquid xenon above 10 keVnr (nuclear recoil energy) are deduced from data acquired using broadband Am-Be neutron sources. The nuclear recoil data from several exposures to two sources were compared to detailed simulations. Energy-dependent scintillation and ionisation yields giving acceptable fits to the data were derived. Efficiency and resolution effects are treated using a light collection Monte Carlo, measured photomultiplier response profiles and hardware trigger studies. A gradual fall in scintillation yield below ~40 keVnr is found, together with a rising ionisation yield; both are in good agreement with the latest independent measurements. The analysis method is applied to both the most recent ZEPLIN-III data, acquired with a significantly upgraded detector and a precision-calibrated Am-Be source, as well as to the earlier data from the first run in 2008. A new method for deriving the recoil scintillation yield, which includes sub-threshold S1...

  15. Time-dependent hydrogen ionisation in the solar chromosphere. I: Methods and first results

    CERN Document Server

    Wedemeyer-Boehm, J L S

    2006-01-01

    An approximate method for solving the rate equations for the hydrogen populations was extended and implemented in the three-dimensional radiation (magneto-)hydrodynamics code CO5BOLD. The method is based on a model atom with six energy levels and fixed radiative rates. It has been tested extensively in one-dimensional simulations. The extended method has been used to create a three-dimensional model that extends from the upper convection zone to the chromosphere. The ionisation degree of hydrogen in our time-dependent simulation is comparable to the corresponding equilibrium value up to 500 km above optical depth unity. Above this height, the non-equilibrium ionisation degree is fairly constant over time and space, and tends to be at a value set by hot propagating shock waves. The hydrogen level populations and electron density are much more constant than the corresponding values for statistical equilibrium, too. In contrast, the equilibrium ionisation degree varies by more than 20 orders of magnitude between...

  16. Boron Separation by the Two-step Ion-Exchange for the Isotopic Measurement of Boron

    Institute of Scientific and Technical Information of China (English)

    WANG,Qing-Zhong(王庆忠); XIAO,Ying-Kai(肖应凯); WANG,Yun-Hui(王蕴惠); ZHANG,Chong-Geng(张崇耿); WEI,Hai-Zhen(魏海珍)

    2002-01-01

    An improved procedure for extraction and purification of boron from natural samples is presented. The separation and purification of boron was carried out using a boron-specific resin, Amberlite IRA743, and a mixed ion exchange resin,Dowex 50W × 8 and Ion Exchanger Ⅱ resin. Using the mixed ion exchange resin which adsorbs all cations and anions except boron, the HCl and other cations and anions left in eluant from the Amberlite IRA 743 were removed effectively. In this case, boron loss can be avoided because the boron-bearing solution does not have to be evaporated to reach dryness to dislodge HCl. The boron recovery ranged from 97.6% to 102% in this study. The isotopic fractionation of boron can be negligible within the precision of the isotopic measurement. The results show that boron separation for the isotopic measurement by using both Amberlite IRA 743 resin and the mixed rein is more effective than that using Amberlite IRA 743 resin alone. The boron in samples of brine, seawater, rock, coral and foraminifer were separated by this procedure. Boron isotopic compositions of these samples were measured by thermal ionization mass spectrometry in this study.

  17. The noble gases adsorption on boron-rich boron nitride nanotubes: A theoretical investigation

    Science.gov (United States)

    Wang, Chong; Guo, Chen

    2017-07-01

    In this work, using density functional theory (DFT) calculations, we have systematically explored the noble gases (Ng = He, Ne, Ar, Kr) adsorption on boron-rich boron nitride nanotubes (BNNTs) surface with antisite boron atom. One or two nitrogen atoms of BNNTs are replaced by boron atoms, which are considered as boron-rich BNNTs for Ng adsorption. It is found that the boron-rich BNNTs can adsorb Ng in exothermic process, and the adsorption energies increase in order from He to Kr. The quantum theory of atoms in molecules (QTAIM) and noncovalent interactions (NCIs) calculations show that the interactions between boron-rich BNNTs and Ng are noncovalent, and the interactions for Ar and Kr are obviously larger than those for He and Ne. The charge transfer from Ng to boron-rich BNNTs and the changes of energy gap caused by Ng adsorption demonstrate that the boron-rich BNNTs are expected to become the Ng adsorption and sensing materials. Moreover, the 2B-BNNTs do not decrease the Ng adsorption interactions on boron-rich BNNTs, compared with 1B-BNNTs. It is expected that the present results will provide a useful guide to develop novel boron nitride nanomaterials for storage and application of Ng.

  18. Study of boron detection limit using the in-air PIGE set-up at LAMFI-USP

    Science.gov (United States)

    Moro, M. V.; Silva, T. F.; Trindade, G. F.; Added, N.; Tabacniks, M. H.

    2014-11-01

    The quantification of small amounts of boron in materials is of extreme importance in different areas of materials science. Boron is an important contaminant and also a silicon dopant in the semiconductor industry. Boron is also extensively used in nuclear power plants, either for neutron shielding or for safety control and boron is an essential nutrient for life, either vegetable or animal. The production of silicon solar cells, by refining metallurgical-grade silicon (MG-Si) requires the control and reduction of several silicon contaminants to very low concentration levels. Boron is one of the contaminants of solar-grade silicon (SG-Si) that must be controlled and quantified at sub-ppm levels. In the metallurgical purification, boron quantification is usually made by Inductive Coupled Plasma Mass Spectrometry, (ICP-MS) but the results need to be verified by an independent analytical method. In this work we present the results of the analysis of silicon samples by Particle Induced Gamma-Ray Emission (PIGE) aiming the quantification of low concentrations of boron. PIGE analysis was carried out using the in-air external beam line of the Laboratory for Materials Analysis with Ion Beans (LAMFI-USP) by the 10B ( p ,αγ(7Be nuclear reaction, and measuring the 429 keV γ-ray. The in-air PIGE measurements at LAMFI have a quantification limit of the order of 1016 at/cm2.

  19. Study of boron detection limit using the in-air PIGE set-up at LAMFI-USP

    Energy Technology Data Exchange (ETDEWEB)

    Moro, M. V.; Silva, T. F.; Trindade, G. F.; Added, N.; Tabacniks, M. H. [Institute of Physics, University of São Paulo, SP (Brazil)

    2014-11-11

    The quantification of small amounts of boron in materials is of extreme importance in different areas of materials science. Boron is an important contaminant and also a silicon dopant in the semiconductor industry. Boron is also extensively used in nuclear power plants, either for neutron shielding or for safety control and boron is an essential nutrient for life, either vegetable or animal. The production of silicon solar cells, by refining metallurgical-grade silicon (MG-Si) requires the control and reduction of several silicon contaminants to very low concentration levels. Boron is one of the contaminants of solar-grade silicon (SG-Si) that must be controlled and quantified at sub-ppm levels. In the metallurgical purification, boron quantification is usually made by Inductive Coupled Plasma Mass Spectrometry, (ICP-MS) but the results need to be verified by an independent analytical method. In this work we present the results of the analysis of silicon samples by Particle Induced Gamma-Ray Emission (PIGE) aiming the quantification of low concentrations of boron. PIGE analysis was carried out using the in-air external beam line of the Laboratory for Materials Analysis with Ion Beams (LAMFI-USP) by the {sup 10}B(p,αγ({sup 7}Be nuclear reaction, and measuring the 429 keV γ-ray. The in-air PIGE measurements at LAMFI have a quantification limit of the order of 10{sup 16} at/cm{sup 2}.

  20. Boron rates for triticale and wheat crops

    Directory of Open Access Journals (Sweden)

    Corrêa Juliano Corulli

    2005-01-01

    Full Text Available No reports are registered on responses to boron fertilization nutrient deficiency and toxicity in triticale crops. The aim of this study was to evaluate triticale response to different rates of boron in comparison to wheat in an hapludox with initial boron level at 0.08 mg dm-3 4 4 factorial design trial completely randomized blocks design (n = 4. Boron rates were 0; 0.62; 1.24 and 1.86 mg dm-3; triticale cultivars were IAC 3, BR 4 and BR 53 and IAPAR 38 wheat crop was used for comparison. The wheat (IAPAR 38 crop presented the highest boron absorption level of all. Among triticale cultivars, the most responsive was IAC 53, presenting similar characteristics to wheat, followed by BR 4; these two crops are considered tolerant to higher boron rates in soil. Regarding to BR 53, no absorption effect was observed, and the cultivars was sensitive to boron toxicity. Absorption responses differed for each genotype. That makes it possible to choose and use the best-adapted plants to soils with different boron rates.

  1. Computational Evidence for the Smallest Boron Nanotube

    Institute of Scientific and Technical Information of China (English)

    Xian Jie LIN; Dong Ju ZHANG; Cheng Bu LIU

    2006-01-01

    The structure of boron nanotubes (BNTs) was found not to be limited to hexagonal pyramidal structures. Based on density functional theory calculations we provided evidence for the smallest boron nanotube, a geometrical analog of the corresponding carbon nanotube. As shown by our calculations, the smallest BNT possesses highly structural, dynamical, and thermal stability, which should be interest for attempts at its synthesis.

  2. Boron carbide whiskers produced by vapor deposition

    Science.gov (United States)

    1965-01-01

    Boron carbide whiskers have an excellent combination of properties for use as a reinforcement material. They are produced by vaporizing boron carbide powder and condensing the vapors on a substrate. Certain catalysts promote the growth rate and size of the whiskers.

  3. Ultratough single crystal boron-doped diamond

    Science.gov (United States)

    Hemley, Russell J [Carnegie Inst. for Science, Washington, DC ; Mao, Ho-Kwang [Carnegie Inst. for Science, Washington, DC ; Yan, Chih-Shiue [Carnegie Inst. for Science, Washington, DC ; Liang, Qi [Carnegie Inst. for Science, Washington, DC

    2015-05-05

    The invention relates to a single crystal boron doped CVD diamond that has a toughness of at least about 22 MPa m.sup.1/2. The invention further relates to a method of manufacturing single crystal boron doped CVD diamond. The growth rate of the diamond can be from about 20-100 .mu.m/h.

  4. Behaviour of boron in Mandovi estuary (Goa)

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Anand, S.P.

    the postmonsoon and removal upto 31.30% in the monsoon were observed. In the postmonsoon months, removal of boron to some extent was observed due to phytoplankton. The pH and dissolved oxygen showed a negative correlation with boron whereas chlorinity...

  5. Possible toxicity of boron on sugar cane

    Energy Technology Data Exchange (ETDEWEB)

    Bravo C., M.

    Analyses of necrotic and green leaf tissues from sugar cane grown in the Tambo Valley (Arequipa, Peru) have shown that the boron concentration in necrotic tissue (average 657.7 ppm) is several times higher than that in the green tissue (average 55.7 ppm). This suggests that the necrosis may be due to boron toxicity.

  6. Boron Carbides As Thermo-electric Materials

    Science.gov (United States)

    Wood, Charles

    1988-01-01

    Report reviews recent theoretical and experimental research on thermoelectric materials. Recent work with narrow-band semiconductors demonstrated possibility of relatively high thermoelectric energy-conversion efficiencies in materials withstanding high temperatures needed to attain such efficiencies. Among promising semiconductors are boron-rich borides, especially boron carbides.

  7. Short and long-term exposure of CNS cell lines to BPA-f a radiosensitizer for boron neutron capture therapy: safety dose evaluation by a battery of cytotoxicity tests.

    Science.gov (United States)

    De Simone, U; Manzo, L; Ferrari, C; Bakeine, J; Locatelli, C; Coccini, T

    2013-03-01

    Despite the current clinical use of boronophenylalanine-fructose (BPA-f), as radiosensitizer, in BNCT application for brain tumors, still remains to be determined the safety dose of this agent. We evaluated the potential risk of primary BPA-f toxicity before neutronic irradiation at different concentrations (0-100μgBeq/ml) after short- and long-term exposure (4-48h and 7-10 days), using a battery of tests (i.e. MTT assay, calcein-AM/Propidium Iodide staining, clonogenic test) in CNS cell models (D384 and SH-SY5Y), and non-neuronal primary human fibroblasts (F26). MTT data showed: (i) no cytotoxic effects after short-term exposure (4h) to any of BPA-f concentrations tested in all cell models; (ii) dose- and time-dependent mitochondrial activity impairment in D384 and SH-SY5Y cells only (with 60% and 40% cell death in D384 and SH-SY5Y, respectively, after 48h exposure to BPA-f 100μgBeq/ml). By Calcein-AM/PI staining, BPA-f treatment was specific toward SH-SY5Y cells only: a dose-dependent cell density reduction was observed, with a more pronounced effect after 48h exposure (15-40% at doses ranging 20-100μgBeq/ml). Clonogenic data revealed dose-dependent decrease of cell proliferative capacity in all cell lines, still the SH-SY5Y cells were the most sensitive ones: the lowest dose (20μgBeq/ml) produced 90% cell decrease. These results indicate dose- and time-dependent cytotoxic effects of BPA-f, with CNS cells showing a lower tolerance compared to fibroblasts. Long-term exposure to BPA-f compromised the proliferative capacity regardless of cell model type (cell sensitivity being SH-SY5Y>D384>F26). In short-time exposure, BPA-f exhibits a safe dosage up to 40μgBeq/ml for the viability of CNS cell lines. Copyright © 2012 Elsevier Inc. All rights reserved.

  8. XPS analysis of boron doped heterofullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Schnyder, B.; Koetz, R. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Muhr, H.J.; Nesper, R. [ETH Zurich, Zurich (Switzerland)

    1997-06-01

    Boron heterofullerenes were generated through arc-evaporation of doped graphite rods in a helium atmosphere. According to mass spectrometric analysis only mono-substituted fullerenes like C{sub 59}B, C{sub 69}B and higher homologues together with a large fraction of higher undoped fullerenes were extracted and enriched when pyridine was used as the solvent. XPS analysis of the extracts indicated the presence of two boron species with significantly different binding energies. One peak was assigned to borid acid. The second one corresponds to boron in the fullerene cage, which is mainly C{sub 59}B, according to the mass spectrum. This boron is in a somewhat higher oxidation state than that of ordinary boron-carbon compounds. The reported synthesis and extraction procedure opens a viable route for production of macroscopic amounts of these compounds. (author) 2 figs., 1 tab., 7 refs.

  9. Stabilization of boron carbide via silicon doping.

    Science.gov (United States)

    Proctor, J E; Bhakhri, V; Hao, R; Prior, T J; Scheler, T; Gregoryanz, E; Chhowalla, M; Giulani, F

    2015-01-14

    Boron carbide is one of the lightest and hardest ceramics, but its applications are limited by its poor stability against a partial phase separation into separate boron and carbon. Phase separation is observed under high non-hydrostatic stress (both static and dynamic), resulting in amorphization. The phase separation is thought to occur in just one of the many naturally occurring polytypes in the material, and this raises the possibility of doping the boron carbide to eliminate this polytype. In this work, we have synthesized boron carbide doped with silicon. We have conducted a series of characterizations (transmission electron microscopy, scanning electron microscopy, Raman spectroscopy and x-ray diffraction) on pure and silicon-doped boron carbide following static compression to 50 GPa non-hydrostatic pressure. We find that the level of amorphization under static non-hydrostatic pressure is drastically reduced by the silicon doping.

  10. Boronated mesophase pitch coke for lithium insertion

    Science.gov (United States)

    Frackowiak, E.; Machnikowski, J.; Kaczmarska, H.; Béguin, F.

    Boronated carbons from mesophase pitch have been used as materials for lithium storage in Li/carbon cells. Doping by boron has been realized by co-pyrolysis of coal tar pitch with the pyridine-borane complex. Amount of boron in mesocarbon microbeads (MCMB) varied from 1.4 to 1.8 wt.% affecting the texture of carbon. Optical microscopy and X-ray diffractograms have shown tendency to more disordered structure for boron-doped carbon. The values of specific reversible capacity ( x) varied from 0.7 to 1.1 depending significantly on the final temperature of pyrolysis (700-1150°C). The optimal charge/discharge performance was observed for boronated carbon heated at 1000°C.

  11. Analysis of peptides and protein digests by reversed phase high performance liquid chromatography-electrospray ionisation mass spectrometry using neutral pH elution conditions.

    Science.gov (United States)

    Yang, Yuanzhong; Boysen, Reinhard I; Chowdhury, Jamil; Alam, Asif; Hearn, Milton T W

    2015-05-04

    In this study, the advantages of carrying out the analysis of peptides and tryptic digests of proteins under gradient elution conditions at pH 6.5 by reversed-phase liquid chromatography (RP-HPLC) and in-line electrospray ionisation mass spectrometry (ESI-MS) are documented. For these RP separations, a double endcapped, bidentate anchored n-octadecyl wide pore silica adsorbent was employed in a capillary column format. Compared to the corresponding analysis of the same peptides and protein tryptic digests using low pH elution conditions for their RP-HPLC separation, this alternative approach provides improved selectivity and more efficient separation of these analytes, thus allowing a more sensitive identification of proteins at different abundance levels, i.e. more tryptic peptides from the same protein could be confidently identified, enabling higher sequence coverage of the protein to be obtained. This approach was further evaluated with very complex tryptic digests derived from a human plasma protein sample using an online two-dimensional (2D) strong cation-exchange (SCX)-RP-HPLC-ESI-MS/MS system. Again, at pH 6.5, with mobile phases of different compositions, improved chromatographic selectivities were obtained, concomitant with more sensitive on-line electrospray ionisation tandem mass spectrometric (ESI-MS/MS) analysis. As a consequence, more plasma proteins could be confidently identified, highlighting the potential of these RP-HPLC methods with elution at pH 6.5 to extend further the scope of proteomic investigations. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Collision strengths and transition probabilities for Co III forbidden lines

    CERN Document Server

    Storey, P J

    2016-01-01

    In this paper we compute the collision strengths and their thermally-averaged Maxwellian values for electron transitions between the fifteen lowest levels of doubly-ionised cobalt, Co^{2+}, which give rise to forbidden emission lines in the visible and infrared region of spectrum. The calculations also include transition probabilities and predicted relative line emissivities. The data are particularly useful for analysing the thermodynamic conditions of supernova ejecta.

  13. The Evaluation of Underground Water Recourses' Boron Concentration and Variation Pattern

    Directory of Open Access Journals (Sweden)

    M Malakootian

    2007-10-01

    Full Text Available Background: Rafsanjan -Noogh- Anar's plain (54°, 52′- 56°, 34′ longitudinally & 29°, 51′- 31°, 31′ latitudinally is one of the Iran's plains located in sub- basin of Daranjir desert. Anar's plain is located at the lowest part of Rafsanjan -Noogh- Anar's plain. According to the geological and field studies of the area, the presence of west and east mounts and deposits re­sulting from evaporation in lower parts of the area are indicative of boron contamination of Anar underground water.Methods: In the present study, 50 deep wells covering Anar plain were selected based on statistical methods. Boron con­centration in each well was measured by Azomethine- H method in the middle of each season, from 2003 to 2007.Results: Comparing the obtained boron concentrations with WHO guidelines, Anar underground water is not safe for drink­ing (mean= 8.88 mg/L. In major part of the plain, the quality of water is not suitable for the growth of plants that are sensi­tive and unresisting to boron. Only in 17.1% of the samples boron concentration was between 0.7-3 mg/L that based on the guide­lines of Food and Agriculture Organization is suitable for some types of plants. Field studies about the area flora con­firm the obtained results too. Changes in the quality of underground water during the years of study, showed a worsening proc­ess over time.Conclusion: To solve the problem, mixing of the water of low boron wells with high boron wells is recommended.

  14. Boron enrichment in martian clay.

    Directory of Open Access Journals (Sweden)

    James D Stephenson

    Full Text Available We have detected a concentration of boron in martian clay far in excess of that in any previously reported extra-terrestrial object. This enrichment indicates that the chemistry necessary for the formation of ribose, a key component of RNA, could have existed on Mars since the formation of early clay deposits, contemporary to the emergence of life on Earth. Given the greater similarity of Earth and Mars early in their geological history, and the extensive disruption of Earth's earliest mineralogy by plate tectonics, we suggest that the conditions for prebiotic ribose synthesis may be better understood by further Mars exploration.

  15. Boron Enrichment in Martian Clay

    Science.gov (United States)

    Nagashima, Kazuhide; Freeland, Stephen J.

    2013-01-01

    We have detected a concentration of boron in martian clay far in excess of that in any previously reported extra-terrestrial object. This enrichment indicates that the chemistry necessary for the formation of ribose, a key component of RNA, could have existed on Mars since the formation of early clay deposits, contemporary to the emergence of life on Earth. Given the greater similarity of Earth and Mars early in their geological history, and the extensive disruption of Earth's earliest mineralogy by plate tectonics, we suggest that the conditions for prebiotic ribose synthesis may be better understood by further Mars exploration. PMID:23762242

  16. Electrophilic Trifluoromethylselenolation of Boronic Acids

    Directory of Open Access Journals (Sweden)

    Clément Ghiazza

    2017-05-01

    Full Text Available Trifluoromethylselenylated compounds are emergent compounds with interesting physicochemical properties that still suffer from a lack of efficient synthetic methods. We recently developed an efficient one-pot strategy to generate in situ CF3SeCl and use it in various reactions. Herein, we continue our study of the reactivity scope of this preformed reagent. Cross-coupling reactions with aromatic and heteroaromatic boronic acids have been investigated. The expected products have been obtained, using a stoichiometric amount of copper, with moderate yields.

  17. Hyaluronic acid as a potential boron carrier for BNCT: Preliminary evaluation.

    Science.gov (United States)

    Zaboronok, A; Yamamoto, T; Nakai, K; Yoshida, F; Uspenskii, S; Selyanin, M; Zelenetskii, A; Matsumura, Akira

    2015-12-01

    Hyaluronic acid (HA), a nonimmunogenic, biocompatible polymer found in different biological tissues, has the potential to attach to CD44 receptors on the surface of certain cancer cells, where the receptor is overexpressed compared with normal cells. Boron-hyaluronic acid (BHA) was tested for its feasibility as a potential agent for BNCT. BHA with low-viscosity 30 kDa HA could be administered by intravenous injection. The compound showed a certain degree of cytotoxicity and accumulation in C6 rat glioma cells in vitro. Instability of the chelate bonds between boron and HA and/or insufficient specificity of CD44 receptors on C6 cells to BHA could account for the insufficient in vitro accumulation. To ensure the future eligibility of BHA for BNCT experiments, using alternative tumor cell lines and chemically securing the chelate bonds or synthesizing BHA with boron covalently attached to HA might be required.

  18. Efficient Synthesis of Boron-Containing α-Acyloxyamide Analogs via Microwave Irradiation

    Directory of Open Access Journals (Sweden)

    Po-Shen Pan

    2013-08-01

    Full Text Available In this report, a Passerini three-component reaction utilizing boron-containing carboxylic acids or aldehydes is discussed. The reaction was carried out in water and facilitated by the use of microwave irradiation. This methodology allowed for the efficient formation of a broad range of boron-containing α-acyloxyamides under mild conditions within a short time. Two series of boron-containing α-acyloxyamides were synthesized and subsequently screened for cytotoxicity using the MTT cell viability assay. Two potential lead compounds were found to have potent activity against the HepG2 cancer cell line, demonstrating the potential of this methodology for use in the development of novel pharmaceuticals.

  19. Prompt gamma-ray emission for future imaging applications in proton-boron fusion therapy

    Science.gov (United States)

    Petringa, G.; Cirrone, G. A. P.; Caliri, C.; Cuttone, G.; Giuffrida, L.; La Rosa, G.; Manna, R.; Manti, L.; Marchese, V.; Marchetta, C.; Margarone, D.; Milluzzo, G.; Picciotto, A.; Romano, F.; Romano, F. P.; Russo, A. D.; Russo, G.; Santonocito, D.; Scuderi, V.

    2017-03-01

    Recently, an approach exploiting the proton therapy biological enhancement by using Boron atoms injected inside a tumor, has been proposed [1-3]. Here, the 11B(p,α)2α nuclear fusion reaction channel, where three alpha particles are produced with an average energy around 4 MeV, is considered [4]. These alphas are able to penetrate the cells nucleus and strongly damage their DNA. In addition, gamma prompts emitted by the proton Boron nuclear reactions can be used for on-line proton beam imaging purposes. In this work an experimental study of the gamma prompt emissions from the proton Boron nuclear reactions has been carried out with the main aim to understand and quantify the most probable emission for future clinical applications.

  20. Boron nanoparticles inhibit turnour growth by boron neutron capture therapy in the murine B16-OVA model

    DEFF Research Database (Denmark)

    Petersen, Mikkel Steen; Petersen, Charlotte Christie; Agger, Ralf

    2008-01-01

    Background: Boron neutron capture therapy usually relies on soluble, rather than particulate, boron compounds. This study evaluated the use of a novel boron nanoparticle for boron neutron capture therapy. Materials and Methods: Two hundred and fifty thousand B16-OVA tumour cells, pre-incubated wi...

  1. Boronline, a new generation of boron meter

    Energy Technology Data Exchange (ETDEWEB)

    Pirat, P. [Rolls-Royce Company, Meylan (France)

    2011-07-01

    Rolls-Royce is a global business providing integrated power systems for use on land, at sea and in the air. The Group has a balanced business portfolio with leading market positions - civil aerospace, defence aerospace, marine and energy Rolls-Royce understands the challenges of design, procurement, manufacture, operation and in-service support of nuclear reactor plants, with over 50 years of experience through the Royal Navy submarine programme. Rolls-Royce can therefore offer full product life-cycle management for new civil nuclear installations, as well as support to existing installations, including plant lifetime extensions. Rolls-Royce produced for 40 years, Instrumentation and Control (I and C) systems of and associated services for nuclear reactors in Europe, including 58 French reactors and others situated in the United States and in others countries, such as China. Rolls-Royce equipped in this domain 200 nuclear reactors in 20 countries. Among all of its nuclear systems, Rolls Royce is presenting to the conference its new generation of on-line boron measurement system, so called Boronline. (authors)

  2. Autoionizing states of atomic boron

    Science.gov (United States)

    Argenti, Luca; Moccia, Roberto

    2016-04-01

    We present a B -spline K -matrix method for three-active-electron atoms in the presence of a polarizable core, with which it is possible to compute multichannel single-ionization scattering states with good accuracy. We illustrate the capabilities of the method by computing the parameters of several autoionizing states of the boron atom, with S2e, 2,o2P and D2e symmetry, up to at least the 2 p2(1S) excitation threshold of the B ii parent ion, as well as selected portions of the photoionization cross section from the ground state. Our results exhibit remarkable gauge consistency, they significantly extend the existing sparse record of data for the boron atom, and they are in good agreement with the few experimental and theoretical data available in the literature. These results open the way to extend to three-active-electron systems the spectral analysis of correlated wave packets in terms of accurate scattering states that has already been demonstrated for two-electron atoms in Argenti and Lindroth [Phys. Rev. Lett. 105, 053002 (2010), 10.1103/PhysRevLett.105.053002].

  3. Combustion synthesis of novel boron carbide

    Science.gov (United States)

    Harini, R. Saai; Manikandan, E.; Anthonysamy, S.; Chandramouli, V.; Eswaramoorthy, D.

    2013-02-01

    The solid-state boron carbide is one of the hardest materials known, ranking third behind diamond and cubic boron nitride. Boron carbide (BxCx) enriched in the 10B isotope is used as a control rod material in the nuclear industry due to its high neutron absorption cross section and other favorable physico-chemical properties. Conventional methods of preparation of boron carbide are energy intensive processes accompanied by huge loss of boron. Attempts were made at IGCAR Kalpakkam to develop energy efficient and cost effective methods to prepare boron carbide. The products of the gel combustion and microwave synthesis experiments were characterized for phase purity by XRD. The carbide formation was ascertained using finger-print spectroscopy of FTIR. Samples of pyrolized/microwave heated powder were characterized for surface morphology using SEM. The present work shows the recent advances in understanding of structural and chemical variations in boron carbide and their influence on morphology, optical and vibrational property results discussed in details.

  4. Method of synthesizing cubic system boron nitride

    Energy Technology Data Exchange (ETDEWEB)

    Yuzu, S.; Sumiya, H.; Degawa, J.

    1987-10-13

    A method is described for synthetically growing cubic system boron nitride crystals by using boron nitride sources, solvents for dissolving the boron nitride sources, and seed crystals under conditions of ultra-high pressure and high temperature for maintaining the cubic system boron nitride stable. The method comprises the following steps: preparing a synthesizing vessel having at least two chambers, arrayed in order in the synthesizing vessel so as to be heated according to a temperature gradient; placing the solvents having different eutectic temperatures in each chamber with respect to the boron nitride sources according to the temperature gradient; placing the boron nitride source in contact with a portion of each of the solvents heated at a relatively higher temperature and placing at least a seed crystal in a portion of each of the solvents heated at a relatively lower temperature; and growing at least one cubic system boron nitride crystal in each of the solvents in the chambers by heating the synthesizing vessel for establishing the temperature gradient while maintaining conditions of ultra-high pressure and high temperature.

  5. X-ray diffraction study of boron produced by pyrolysis of boron tribromide

    Science.gov (United States)

    Rosenberg, David

    The goal of this research was to determine the composition of boron deposits produced by pyrolysis of boron tribromide, and to use the results to (a) determine the experimental conditions (reaction temperature, etc.) necessary to produce alpha-rhombohedral boron and (b) guide the development/refinement of the pyrolysis experiments such that large, high purity crystals of alpha-rhombohedral boron can be produced with consistency. Developing a method for producing large, high purity alpha-rhombohedral boron crystals is of interest because such crystals could potentially be used to achieve an alpha-rhombohedral boron based neutron detector design (a solid-state detector) that could serve as an alternative to existing neutron detector technologies. The supply of neutron detectors in the United States has been hampered for a number of years due to the current shortage of helium-3 (a gas used in many existing neutron detector technologies); the development of alternative neutron detector technology such as an alpha-rhombohedral boron based detector would help provide a more sustainable supply of neutron detectors in this country. In addition, the prospect/concept of an alpha-rhombohedral boron based neutron detector is attractive because it offers the possibility of achieving a design that is smaller, longer life, less power consuming, and potentially more sensitive than existing neutron detectors. The main difficulty associated with creating an alpha-rhombohedral boron based neutron detector is that producing large, high purity crystals of alpha-rhombohedral boron is extremely challenging. Past researchers have successfully made alpha-rhombohedral boron via a number of methods, but no one has developed a method for consistently producing large, high purity crystals. Alpha-rhombohedral boron is difficult to make because it is only stable at temperatures below around 1100-1200 °C, its formation is very sensitive to impurities, and the conditions necessary for its

  6. From Boron Cluster to Two-Dimensional Boron Sheet on Cu(111) Surface: Growth Mechanism and Hole Formation

    OpenAIRE

    Hongsheng Liu; Junfeng Gao; Jijun Zhao

    2013-01-01

    As attractive analogue of graphene, boron monolayers have been theoretically predicted. However, due to electron deficiency of boron atom, synthesizing boron monolayer is very challenging in experiments. Using first-principles calculations, we explore stability and growth mechanism of various boron sheets on Cu(111) substrate. The monotonic decrease of formation energy of boron cluster BN with increasing cluster size and low diffusion barrier for a single B atom on Cu(111) surface ensure cont...

  7. KINETIC SIMULATIONS OF THERMOLUMINESCENCE DOSE RESPONSE: LONG OVERDUE CONFRONTATION WITH THE EFFECTS OF IONISATION DENSITY.

    Science.gov (United States)

    Horowitz, Y S; Eliyahu, I; Oster, L

    2016-12-01

    The reader will time-travel through almost seven decades of kinetic models and mathematical simulations of thermoluminescence (TL) characteristics based on the band-gap theory of the solid state. From post-World-War II, ideas concerning electron trapping mechanisms to the highly idealised one trap-one recombination (OTOR) model first elaborated in 1956 but still in 'high gear' today. The review caresses but purposely avoids in-depth discussion of the endless stream of papers discussing the intricacies of glow peak shapes arising from first-order, second-order, mixed-order and general-order kinetics predominantly based on non-interacting systems, and then on to the more physically realistic scenarios that have attempted to analyse complex systems involving ever greater numbers of interacting trapping centres, luminescent centres and non-luminescent centres. The review emphasises the difficulty the band-gap models have in the simulation of dose response linear/supralinear behaviour and especially the dependence of the supralinearity on ionisation density. The significance of the non-observation of filling-rate supralinearity in the absorption stage is emphasised since it removes from consideration the possibility of TL supralinearity arising from irradiation stage supralinearity. The importance of the simultaneous action of both localised and delocalised transitions has gradually penetrated the mindset of the community of kinetic researchers, but most simulations have concentrated on the shape of glow peaks and the extraction of the glow peak parameters, E (the thermal activation energy) and s (the attempt-to-escape frequency). The simulation of linear/supralinear dose response and its dependence on ionisation density have been largely avoided until recently due to the fundamental schism between the effects of ionisation density and some basic assumptions of the band-gap model. The review finishes with an in-depth presentation and discussion of the most recent

  8. Tribochemical interactions of boron carbides against steel

    Energy Technology Data Exchange (ETDEWEB)

    Gogotsi, Yu.G. (Univ. Karlsruhe, Inst. fuer Keramik im Maschinenbau (Germany)); Koval' chenko, A.M.; Kossko, I.A. (Inst. for Problems of Materials Science, Ukrainian Academy of Sciences, Kiev (Ukraine))

    1992-04-15

    Auger electron spectroscopy and electron microscopy were used to investigate the surface chemistry and tribological properties of boron carbide sliding against steel. It was revealed that the interacting process was accompanied by the diffusion of the ceramic elements into steel and by the oxidation of the steel and ceramic surfaces due to the oxygen presence in the atmosphere. It was established that the oxidation process in air or during friction tests leads to a graphitized layer on the boron carbide surface under the B{sub 2}O{sub 3} film. It was demonstrated that the oxidation caused a decrease in the friction coefficient of boron carbide sliding against steel. (orig.).

  9. Developments in boron magnetic resonance imaging (MRI)

    Energy Technology Data Exchange (ETDEWEB)

    Schweizer, M.

    1995-11-01

    This report summarizes progress during the past year on maturing Boron-11 magnetic resonance imaging (MRI) methodology for noninvasive determination of BNCT agents (BSH) spatially in time. Three major areas are excerpted: (1) Boron-11 MRI of BSH distributions in a canine intracranial tumor model and the first human glioblastoma patient, (2) whole body Boron-11 MRI of BSH pharmacokinetics in a rat flank tumor model, and (3) penetration of gadolinium salts through the BBB as a function of tumor growth in the canine brain.

  10. Characterisation of the Muon Beams for the Muon Ionisation Cooling Experiment

    CERN Document Server

    Adams, D.; Alekou, A.; Apollonio, M.; Asfandiyarov, R.; Back, J.; Barber, G.; Barclay, P.; de Bari, A.; Bayes, R.; Bayliss, V.; Bertoni, R.; Blackmore, V.J.; Blondel, A.; Blot, S.; Bogomilov, M.; Bonesini, M.; Booth, C.N.; Bowring, D.; Boyd, S.; Bradshaw, T.W.; Bravar, U.; Bross, A.D.; Capponi, M.; Carlisle, T.; Cecchet, G.; Charnley, G.; Cobb, J.H.; Colling, D.; Collomb, N.; Coney, L.; Cooke, P.; Courthold, M.; Cremaldi, L.M.; DeMello, A.; Dick, A.; Dobbs, A.; Dornan, P.; Fayer, S.; Filthaut, F.; Fish, A.; Fitzpatrick, T.; Fletcher, R.; Forrest, D.; Francis, V.; Freemire, B.; Fry, L.; Gallagher, A.; Gamet, R.; Gourlay, S.; Grant, A.; Graulich, J.S.; Griffiths, S.; Hanlet, P.; Hansen, O.M.; Hanson, G.G.; Harrison, P.; Hart, T.L.; Hartnett, T.; Hayler, T.; Heidt, C.; Hills, M.; Hodgson, P.; Iaciofano, A.; Ishimoto, S.; Kafka, G.; Kaplan, D.M.; Karadzhov, Y.; Kim, Y.K.; Kolev, D.; Kuno, Y.; Kyberd, P.; Lau, W.; Leaver, J.; Leonova, M.; Li, D.; Lintern, A.; Littlefield, M.; Long, K.; Lucchini, G.; Luo, T.; Macwaters, C.; Martlew, B.; Martyniak, J.; Middleton, S.; Moretti, A.; Moss, A.; Muir, A.; Mullacrane, I.; Nebrensky, J.J.; Neuffer, D.; Nichols, A.; Nicholson, R.; Nugent, J.C.; Onel, Y.; Orestano, D.; Overton, E.; Owens, P.; Palladino, V.; Palmer, R.B.; Pasternak, J.; Pastore, F.; Pidcott, C.; Popovic, M.; Preece, R.; Prestemon, S.; Rajaram, D.; Ramberger, S.; Rayner, M.A.; Ricciardi, S.; Richards, A.; Roberts, T.J.; Robinson, M.; Rogers, C.; Ronald, K.; Rubinov, P.; Rucinski, R.; Rusinov, I.; Sakamoto, H.; Sanders, D.A.; Santos, E.; Savidge, T.; Smith, P.J.; Snopok, P.; Soler, F.J.P.; Stanley, T.; Summers, D.J.; Takahashi, M.; Tarrant, J.; Taylor, I.; Tortora, L.; Torun, Y.; Tsenov, R.; Tunnell, C.D.; Vankova, G.; Verguilov, V.; Virostek, S.; Vretenar, M.; Walaron, K.; Watson, S.; White, C.; Whyte, C.G.; Wilson, A.; Wisting, H.; Zisman, M.

    2013-01-01

    A novel single-particle technique to measure emittance has been developed and used to characterise seventeen different muon beams for the Muon Ionisation Cooling Experiment (MICE). The muon beams, whose mean momenta vary from 171 to 281 MeV/c, have emittances of approximately 1.5--2.3 \\pi mm-rad horizontally and 0.6--1.0 \\pi mm-rad vertically, a horizontal dispersion of 90--190 mm and momentum spreads of about 25 MeV/c. There is reasonable agreement between the measured parameters of the beams and the results of simulations. The beams are found to meet the requirements of MICE.

  11. Liquid chromatography with electrospray ionisation mass spectrometric detection of phenolic compounds from Olea europaea.

    Science.gov (United States)

    Ryan, D; Robards, K; Prenzler, P; Jardine, D; Herlt, T; Antolovich, M

    1999-09-10

    The results demonstrate the potential of electrospray ionisation mass spectrometry for the specific detection of phenolic species in olives. Phenolic compounds were detected with greater sensitivity in the negative ion mode, but results from positive and negative ion modes were complementary with the positive ion mode showing structurally significant fragments. This is demonstrated by the identification of oleuropein and isomers of verbascoside. The structure of the latter were confirmed by retention, mass spectral and nuclear magnetic resonance data. These isomers have not previously been reported in olive.

  12. EVOLUTION OF THE IEC AND EN STANDARDS FOR INDIVIDUAL MONITORING OF IONISING RADIATION.

    Science.gov (United States)

    Voytchev, M; Behrens, R; Ambrosi, P; Radev, R; Chiaro, P

    2016-09-01

    This article presents the evolution of the International Electrotechnical Commission (IEC) and the European standards for individual monitoring of ionising radiation issued, respectively, from the committees IEC/Sub Committee 45B and European Committee for Electro-technical Standardization/Technical Committee 45B 'Radiation protection instrumentation'. Standards for passive individual photon and beta dosimetry systems as well as those for active individual monitors are discussed. A neutron ambient dose equivalent (rate) meter standard and a technical report concerning the determination of uncertainty in measurement are also covered. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  13. Characterisation of the muon beams for the Muon Ionisation Cooling Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Adams, D.; et al.,

    2013-10-01

    A novel single-particle technique to measure emittance has been developed and used to characterise seventeen different muon beams for the Muon Ionisation Cooling Experiment (MICE). The muon beams, whose mean momenta vary from 171 to 281 MeV/c, have emittances of approximately 1.5--2.3 \\pi mm-rad horizontally and 0.6--1.0 \\pi mm-rad vertically, a horizontal dispersion of 90--190 mm and momentum spreads of about 25 MeV/c. There is reasonable agreement between the measured parameters of the beams and the results of simulations. The beams are found to meet the requirements of MICE.

  14. The potential use of diamond coated tungsten tips as a field ionisation source

    Energy Technology Data Exchange (ETDEWEB)

    Brown, A.; Prawer, S.; Legge, G.J.F.; Kostidis, L.I. [Melbourne Univ., Parkville, VIC (Australia). School of Physics

    1996-12-31

    Tungsten tips are convenient for use in a high brightness gaseous phase field ionisation source. However, the lifetime of these tips is not adequate for practical use. The authors are investigating whether coating tungsten tips with diamond using Chemical Vapor Deposition (CVD) will improve the practicality of using these tips by an improvement in longevity of the source and/or an improvement in brightness due to the effects of the property of negative electron affinity which has been observed on CVD diamond. 1 ref.

  15. Design and performance of an ionisation chamber for the measurement of low alpha-activities

    CERN Document Server

    Hartmann, Andreas; Krüger, Felix; Sobiella, Manfred; Wilsenach, Heinrich; Zuber, Kai

    2015-01-01

    A new ionisation chamber for alpha-spectroscopy has been built from radio-pure materials for the purpose of investigating long lived alpha-decays. The measurement makes use of pulse shape analysis to discriminate between signal and background events. The design and performance of the chamber is described in this paper. A background rate of ($10.9 \\pm 0.6$) counts per day in the energy region of 1 MeV to 9 MeV was achieved with a run period of 30.8 days. The background is dominantly produced by radon daughters.

  16. Characterisation of the muon beams for the Muon Ionisation Cooling Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Adams, D.; Barclay, P.; Bayliss, V.; Bradshaw, T.W.; Courthold, M.; Francis, V.; Fry, L.; Hayler, T.; Hills, M.; Lintern, A.; Macwaters, C.; Nichols, A.; Preece, R.; Ricciardi, S.; Rogers, C.; Stanley, T.; Tarrant, J.; Watson, S.; Wilson, A. [Harwell Oxford, STFC Rutherford Appleton Laboratory, Didcot (United Kingdom); Adey, D.; Back, J.; Boyd, S.; Harrison, P.; Pidcott, C.; Taylor, I. [University of Warwick, Department of Physics, Coventry (United Kingdom); Alekou, A.; Apollonio, M.; Barber, G.; Colling, D.; Dobbs, A.; Dornan, P.; Fayer, S.; Fish, A.; Hunt, C.; Leaver, J.; Long, K.; Martyniak, J.; Middleton, S.; Pasternak, J.; Richards, A.; Santos, E.; Savidge, T.; Takahashi, M. [Imperial College London, Department of Physics, Blackett Laboratory, London (United Kingdom); Asfandiyarov, R.; Blondel, A.; Graulich, J.S.; Karadzhov, Y.; Verguilov, V.; Wisting, H. [Universite de Geneve, DPNC, Section de Physique, Geneva (Switzerland); De Bari, A.; Cecchet, G. [Sezione INFN Pavia (Italy); Dipartimento di Fisica Nucleare e Teorica, Pavia (Italy); Bayes, R.; Forrest, D.; Nugent, J.C.; Soler, F.J.P.; Walaron, K. [The University of Glasgow, School of Physics and Astronomy, Glasgow (United Kingdom); Bertoni, R.; Bonesini, M.; Lucchini, G. [Sezione INFN Milano Bicocca (Italy); Dipartimento di Fisica G. Occhialini, Milano (Italy); Blackmore, V.J.; Carlisle, T.; Cobb, J.H.; Lau, W.; Rayner, M.A.; Tunnell, C.D. [University of Oxford, Department of Physics, Oxford (United Kingdom); Blot, S.; Kim, Y.K. [University of Chicago, Enrico Fermi Institute, Chicago, IL (United States); Bogomilov, M.; Kolev, D.; Rusinov, I.; Tsenov, R.; Vankova, G. [St. Kliment Ohridski University of Sofia, Department of Atomic Physics, Sofia (Bulgaria); Booth, C.N.; Hodgson, P.; Nicholson, R.; Overton, E.; Robinson, M.; Smith, P.J. [University of Sheffield, Department of Physics and Astronomy, Sheffield (United Kingdom); Bowring, D.; DeMello, A.; Gourlay, S.; Li, D.; Prestemon, S.; Virostek, S.P.; Zisman, M.S. [Lawrence Berkeley National Laboratory, Berkeley, CA (United States); Bravar, U. [University of New Hampshire, Durham, NH (United States); Bross, A.D.; Fitzpatrick, T.; Leonova, M.; Moretti, A.; Neuffer, D.; Popovic, M.; Rubinov, P.; Rucinski, R. [Fermilab, Batavia, IL (United States); Capponi, M.; Iaciofano, A.; Orestano, D.; Pastore, F.; Tortora, L. [Sezione INFN Roma Tre e Dipartimento di Fisica, Roma (Italy); Charnley, G.; Collomb, N.; Gallagher, A.; Grant, A.; Griffiths, S.; Hartnett, T.; Martlew, B.; Moss, A.; Muir, A.; Mullacrane, I.; Owens, P.; White, C. [STFC Daresbury Laboratory, Cheshire (United Kingdom); Coney, L.; Fletcher, R.; Hanson, G.G.; Heidt, C. [University of California, Riverside, CA (United States); Cooke, P.; Gamet, R. [University of Liverpool, Department of Physics, Liverpool (United Kingdom); Cremaldi, L.M.; Hart, T.L.; Luo, T.; Sanders, D.A.; Summers, D.J. [University of Mississippi, Oxford, MS (United States); Dick, A.J.; Ronald, K.; Whyte, C.G. [University of Strathclyde, Department of Physics, Glasgow (United Kingdom); Filthaut, F. [NIKHEF, Amsterdam (Netherlands); Freemire, B.; Hanlet, P.; Kafka, G.; Kaplan, D.M.; Rajaram, D.; Snopok, P.; Torun, Y. [Illinois Institute of Technology, Chicago, IL (United States); Hansen, O.M.; Ramberger, S.; Vretenar, M. [CERN, Geneva (Switzerland); Ishimoto, S. [Institute of Particle and Nuclear Studies, High Energy Accelerator Research Organization (KEK), Tsukuba, Ibaraki (Japan); Kuno, Y.; Sakamoto, H. [Osaka University, Graduate School of Science, Department of Physics, Toyonaka, Osaka (Japan); Kyberd, P.; Littlefield, M.; Nebrensky, J.J. [Brunel University, Uxbridge (United Kingdom); Onel, Y. [University of Iowa, Department of Physics and Astronomy, Iowa City, IA (United States); Palladino, V. [Universita Federico II, Sezione INFN Napoli (Italy); Dipartimento di Fisica, Napoli (Italy); Palmer, R.B. [Brookhaven National Laboratory, Upton, NY (US); Roberts, T.J. [Muons, Inc., Batavia, IL (US); Collaboration: The MICE Collaboration

    2013-10-15

    A novel single-particle technique to measure emittance has been developed and used to characterise seventeen different muon beams for the Muon Ionisation Cooling Experiment (MICE). The muon beams, whose mean momenta vary from 171 to 281 MeV/c, have emittances of approximately 1.2-2.3 {pi} mm-rad horizontally and 0.6-1.0 {pi} mm-rad vertically, a horizontal dispersion of 90-190 mm and momentum spreads of about 25 MeV/c. There is reasonable agreement between the measured parameters of the beams and the results of simulations. The beams are found to meet the requirements of MICE. (orig.)

  17. Boronophenylalanine, a boron delivery agent for boron neutron capture therapy, is transported by ATB0,+, LAT1 and LAT2.

    Science.gov (United States)

    Wongthai, Printip; Hagiwara, Kohei; Miyoshi, Yurika; Wiriyasermkul, Pattama; Wei, Ling; Ohgaki, Ryuichi; Kato, Itsuro; Hamase, Kenji; Nagamori, Shushi; Kanai, Yoshikatsu

    2015-03-01

    The efficacy of boron neutron capture therapy relies on the selective delivery of boron carriers to malignant cells. p-Boronophenylalanine (BPA), a boron delivery agent, has been proposed to be localized to cells through transporter-mediated mechanisms. In this study, we screened aromatic amino acid transporters to identify BPA transporters. Human aromatic amino acid transporters were functionally expressed in Xenopus oocytes and examined for BPA uptake and kinetic parameters. The roles of the transporters in BPA uptake were characterized in cancer cell lines. For the quantitative assessment of BPA uptake, HPLC was used throughout the study. Among aromatic amino acid transporters, ATB(0,+), LAT1 and LAT2 were found to transport BPA with Km values of 137.4 ± 11.7, 20.3 ± 0.8 and 88.3 ± 5.6 μM, respectively. Uptake experiments in cancer cell lines revealed that the LAT1 protein amount was the major determinant of BPA uptake at 100 μM, whereas the contribution of ATB(0,+) became significant at 1000 μM, accounting for 20-25% of the total BPA uptake in MCF-7 breast cancer cells. ATB(0,+), LAT1 and LAT2 transport BPA at affinities comparable with their endogenous substrates, suggesting that they could mediate effective BPA uptake in vivo. The high and low affinities of LAT1 and ATB(0,+), respectively, differentiate their roles in BPA uptake. ATB(0,+), as well as LAT1, could contribute significantly to the tumor accumulation of BPA at clinical dose.

  18. Characterization of boron tolerant bacteria isolated from a fly ash dumping site for bacterial boron remediation.

    Science.gov (United States)

    Edward Raja, Chellaiah; Omine, Kiyoshi

    2013-08-01

    Boron is an essential micronutrient for plants, but can above certain concentrations be toxic to living organisms. A major environmental concern is the removal of boron from contaminated water and fly ash. For this purpose, the samples were collected from a fly ash dumping site, Nagasaki prefecture, Japan. The chemical characteristics and heavy metal concentration of the samples were performed by X-ray fluorescent analysis and leaching test. For bacterial analysis, samples were collected in sterile plastic sheets and isolation was carried out by serial dilution method. The boron tolerant isolates that showed values of maximum inhibitory concentration toward boron ranging from 100 to 260 mM level were screened. Based on 16S rRNA sequencing and phylogenetic analysis, the isolates were most closely related to the genera Bacillus, Lysinibacillus, Microbacterium and Ralstonia. The boron tolerance of these strains was also associated with resistant to several heavy metals, such as As (III), Cr (VI), Cd, Cu, Pb, Ni, Se (III) and Zn. Indeed, these strains were arsenic oxidizing bacteria confirmed by silver nitrate test. These strains exhibited their salt resistances ranging from 4 to 15 % were determined in Trypticase soy agar medium. The boron tolerant strains were capable of removing 0.1-2.0 and 2.7-3.7 mg l(-1) boron from the medium and fly ash at 168 h. Thus, we have successfully identified the boron tolerant and removal bacteria from a fly ash dumping site for boron remediation.

  19. Bonding in boron: building high-pressure phases from boron sheets

    Energy Technology Data Exchange (ETDEWEB)

    Kunstmann, Jens [Institute for Materials Science and Max Bergmann Center of Biomaterials, Dresden University of Technology (Germany); Boeri, Lilia [Max Planck Institute for Solid State Research, Stuttgart (Germany); Kortus, Jens [Institute for Theoretical Physics, TU Bergakademie Freiberg (Germany)

    2010-07-01

    We present the results of a study of the high pressure phase diagram of elemental boron, using full-potential density functional calculations. We show that at high pressures (P > 100 GPa) boron crystallizes in quasi-layered bulk phases, characterized by in-plane multicenter bonds and out-of-plane unidimensional sigma bonds. These structures are all metallic, in contrast to the low-pressure icosahedral ones, which are semiconducting. We show that the structure and bonding of layered bulk phases can be easily described in terms of single puckered boron sheets. Our results bridge the gap between boron nanostructures and bulk phases.

  20. Formation of the helium extreme-UV resonance lines

    Science.gov (United States)

    Golding, T. P.; Leenaarts, J.; Carlsson, M.

    2017-01-01

    Context. While classical models successfully reproduce intensities of many transition region lines, they predict helium extreme-UV (EUV) line intensities roughly an order of magnitude lower than the observed value. Aims: Our aim is to determine the relevant formation mechanism(s) of the helium EUV resonance lines capable of explaining the high intensities under quiet Sun conditions. Methods: We synthesised and studied the emergent spectra from a 3D radiation-magnetohydrodynamics simulation model. The effects of coronal illumination and non-equilibrium ionisation of hydrogen and helium are included self-consistently in the numerical simulation. Results: Radiative transfer calculations result in helium EUV line intensities that are an order of magnitude larger than the intensities calculated under the classical assumptions. The enhanced intensity of He iλ584 is primarily caused by He ii recombination cascades. The enhanced intensity of He iiλ304 and He iiλ256 is caused primarily by non-equilibrium helium ionisation. Conclusions: The analysis shows that the long standing problem of the high helium EUV line intensities disappears when taking into account optically thick radiative transfer and non-equilibrium ionisation effects.

  1. Boron-Based (Nano-Materials: Fundamentals and Applications

    Directory of Open Access Journals (Sweden)

    Umit B. Demirci

    2016-09-01

    Full Text Available The boron (Z = 5 element is unique. Boron-based (nano-materials are equally unique. Accordingly, the present special issue is dedicated to crystalline boron-based (nano-materials and gathers a series of nine review and research articles dealing with different boron-based compounds. Boranes, borohydrides, polyhedral boranes and carboranes, boronate anions/ligands, boron nitride (hexagonal structure, and elemental boron are considered. Importantly, large sections are dedicated to fundamentals, with a special focus on crystal structures. The application potentials are widely discussed on the basis of the materials’ physical and chemical properties. It stands out that crystalline boron-based (nano-materials have many technological opportunities in fields such as energy storage, gas sorption (depollution, medicine, and optical and electronic devices. The present special issue is further evidence of the wealth of boron science, especially in terms of crystalline (nano-materials.

  2. Boron-10 loaded inorganic shielding material

    Science.gov (United States)

    Baker, S. I.; Ryskiewicz, R. S.

    1972-01-01

    Shielding material containing Boron 10 and gadoliunium for neutron absorption has been developed to reduce interference from low energy neutrons in measurement of fission neutron spectrum using Li-6 fast neutron spectrometer.

  3. Catalytic Asymmetric Synthesis of Phosphine Boronates

    NARCIS (Netherlands)

    Hornillos, Valentin; Vila, Carlos; Otten, Edwin; Feringa, Ben L.

    2015-01-01

    The first catalytic enantioselective synthesis of ambiphilic phosphine boronate esters is presented. The asymmetric boration of ,-unsaturated phosphine oxides catalyzed by a copper bisphosphine complex affords optically active organoboronate esters that bear a vicinal phosphine oxide group in good y

  4. Boron-Filled Hybrid Carbon Nanotubes

    Science.gov (United States)

    Patel, Rajen B.; Chou, Tsengming; Kanwal, Alokik; Apigo, David J.; Lefebvre, Joseph; Owens, Frank; Iqbal, Zafar

    2016-07-01

    A unique nanoheterostructure, a boron-filled hybrid carbon nanotube (BHCNT), has been synthesized using a one-step chemical vapor deposition process. The BHCNTs can be considered to be a novel form of boron carbide consisting of boron doped, distorted multiwalled carbon nanotubes (MWCNTs) encapsulating boron nanowires. These MWCNTs were found to be insulating in spite of their graphitic layered outer structures. While conventional MWCNTs have great axial strength, they have weak radial compressive strength, and do not bond well to one another or to other materials. In contrast, BHCNTs are shown to be up to 31% stiffer and 233% stronger than conventional MWCNTs in radial compression and have excellent mechanical properties at elevated temperatures. The corrugated surface of BHCNTs enables them to bond easily to themselves and other materials, in contrast to carbon nanotubes (CNTs). BHCNTs can, therefore, be used to make nanocomposites, nanopaper sheets, and bundles that are stronger than those made with CNTs.

  5. Spectromicroscopy in Boron Neutron Capture Therapy Research

    Science.gov (United States)

    Gilbert, Benjamin; Redondo, Jose; Andres, Roger; Suda, Takashi; Neumann, Michael; Steen, Steffi; Gabel, Detlef; Mercanti, Delio; Ciotti, Teresa; Perfetti, Paolo; Margaritondo, Giorgio; de Stasio, Gelsomina

    1998-03-01

    The MEPHISTO synchrotron imaging spectromicroscope can analyse ashed cells or tissue sections to reveal the microdistribution of trace elements. MEPHISTO performs core level x-ray absorption spectroscopy with synchrotron radiation, and uses an electron optics system to provide magnified photoelectron images. An application of the MEPHISTO spectromicroscope is in boron neutron capture therapy (BNCT). BNCT is a binary cancer therapy that will selectively destroy cancer cells provided that compounds containing a boron isotope are selectively accumulated in tumor tissue. Important factors for the success of BNCT include the ability to target every cancer cell, and the distribution of boron inside the cell. To investigate the boron distribution in tissue, sections of human glioblastoma containing a BNCT compound, and stained with nickel against a protein found in the nuclei of proliferating (cancer) cells, were studied with MEPHISTO.

  6. Boron-Filled Hybrid Carbon Nanotubes

    Science.gov (United States)

    Patel, Rajen B.; Chou, Tsengming; Kanwal, Alokik; Apigo, David J.; Lefebvre, Joseph; Owens, Frank; Iqbal, Zafar

    2016-01-01

    A unique nanoheterostructure, a boron-filled hybrid carbon nanotube (BHCNT), has been synthesized using a one-step chemical vapor deposition process. The BHCNTs can be considered to be a novel form of boron carbide consisting of boron doped, distorted multiwalled carbon nanotubes (MWCNTs) encapsulating boron nanowires. These MWCNTs were found to be insulating in spite of their graphitic layered outer structures. While conventional MWCNTs have great axial strength, they have weak radial compressive strength, and do not bond well to one another or to other materials. In contrast, BHCNTs are shown to be up to 31% stiffer and 233% stronger than conventional MWCNTs in radial compression and have excellent mechanical properties at elevated temperatures. The corrugated surface of BHCNTs enables them to bond easily to themselves and other materials, in contrast to carbon nanotubes (CNTs). BHCNTs can, therefore, be used to make nanocomposites, nanopaper sheets, and bundles that are stronger than those made with CNTs. PMID:27460526

  7. Synthesis of Boron-Containing Primary Amines

    Directory of Open Access Journals (Sweden)

    Sheng-Hsuan Chung

    2013-10-01

    Full Text Available In this study, boron-containing primary amines were synthesized for use as building blocks in the study of peptoids. In the first step, Gabriel synthesis conditions were modified to enable the construction of seven different aminomethylphenyl boronate esters in good to excellent yields. These compounds were further utilized to build peptoid analogs via an Ugi four-component reaction (Ugi-4CR under microwave irradiation. The prepared Ugi-4CR boronate esters were then successfully converted to the corresponding boronic acids. Finally, the peptoid structures were successfully modified by cross-coupling to aryl/heteroaryl chlorides via a palladium-mediated Suzuki coupling reaction to yield the corresponding derivatives in moderate to good yields.

  8. Boron toxicity in oil palm (Elaeis guineensis)

    Energy Technology Data Exchange (ETDEWEB)

    Rajaratnam, J.A.

    1973-01-01

    Potted oil palms were treated with fertilizer of borate-46 at several concentrations and the plants were observed for boron toxicity effects. Toxicity symptoms were apparent at high rates but not at rates equivalent to typical Malaysian soils.

  9. Room-temperature near-infrared electroluminescence from boron-diffused silicon pn junction diodes

    Directory of Open Access Journals (Sweden)

    Si eLi

    2015-02-01

    Full Text Available Silicon pn junction diodes with different doping concentrations were prepared by boron diffusion into Czochralski (CZ n-type silicon substrate. Their room-temperature near-infrared electroluminescence (EL was measured. In the EL spectra of the heavily boron doped diode, a luminescence peak at ~1.6 m (0.78 eV was observed besides the band-to-band line (~1.1eV under the condition of high current injection, while in that of the lightly boron doped diode only the band-to-band line was observed. The intensity of peak at 0.78 eV increases exponentially with current injection with no observable saturation at room temperature. Furthermore, no dislocations were found in the cross-sectional transmission electron microscopy image, and no dislocation-related luminescence was observed in the low-temperature photoluminescence spectra. We deduce the 0.78 eV emission originates from the irradiative recombination in the strain region of diodes caused by the diffusion of large number of boron atoms into silicon crystal lattice.

  10. Combustion Behavior of Free Boron Slurry Droplets,

    Science.gov (United States)

    2014-09-26

    weak disruptive behavior while pure JP-1t burn quiescently, except for a flash extinction which occurs at the termination of combustion. The...I AD-R158 628 COMBUSTION BEHAVIOR OF FREE BORON SLURRY DROPLETS(U) i/i I PRINCETON UNIV NJ DEPT OF MECHANICAL AND AEROSPACE ENINEERIN., F TAKAHASHI...COMBUSTION BEHAVIOR OF FREE BORON SLURRY DROPLETS TAM by F. Takahashi, F.L. Dryer, and F.A. Williams Department of M~echanical and keyosase Engineering

  11. Alternative Process for Manufacturing of Thin Layers of Boron for Neutron Measurement

    Energy Technology Data Exchange (ETDEWEB)

    Auge, Gregoire; Partyka, Stanislas [Onet Technologies (France); Guerard, Bruno; Buffet, Jean-Claude [Institut Laue Langevin - ILL, Grenoble (France)

    2015-07-01

    Due to the worldwide shortage of helium 3, Boron-lined proportional counters are developed intensively by several groups. Up to now, thin boron containing layers for neutron detectors are essentially produced by sputtering of boron carbide (B{sub 4}C). This technology provides high quality films but it is slow and expensive. Our paper describes a novel and inexpensive technology for producing boron layers. This technology is based on chemical synthesis of boron 10 nanoparticles, and on electrophoretic deposition of these particles on metallic plates, or on metallic pieces with more complex shapes. The chemical synthesis consists in: - Heating boron 10 with lithium up to 700 deg. C under inert atmosphere: an intermetallic compound, LiB, is produced; - Hydrolysing this intermetallic compound: LiB + H{sub 2}O → B + Li{sup +} + OH{sup -} + 1/2H{sub 2}, where B is under the form of nanoparticles; - Purifying the suspension of boron nanoparticles in water, from lithium hydroxide, by successive membrane filtrations; - Evaporating the purified suspension, in order to get a powder of nanoparticles. The obtained nanoparticles have size around 300 nm, with a high porosity, of about 50%. This particle size is equivalent to about 150 nm massive particles. The nanoparticles are then put into suspension in a specific solvent, in order to perform deposition on metallic surfaces, by electrophoretic method. The solvent is chosen so that it is not electrolysed even under voltages of several tens of volts. An acid is dissolved into the solvent, so that the nanoparticles are positively charged. Deposition is performed on the cathode within about 10 min. The cathode could be an aluminium plate, or a nickel coated aluminium plate. Homogeneous deposition may also be performed on complex shapes, like grids in a Multigrid detector. A large volume of pieces, can be coated with a Boron-10 film in a few hours. The thickness of the layer can be adjusted according to the required neutron

  12. On the effect of the ionising background on the Ly{\\alpha} forest autocorrelation function

    CERN Document Server

    Gontcho, Satya Gontcho A; Busca, Nicolás G

    2014-01-01

    An analytical framework is presented to understand the effects of a fluctuating intensity of the cosmic ionising background on the correlations of the Ly{\\alpha} forest transmission fraction measured in quasar spectra. In the absence of intensity fluctuations, the Ly{\\alpha} power spectrum should have the expected cold dark matter power spectrum with redshift distortions in the linear regime, with a bias factor b_{\\delta} and a redshift distortion parameter {\\beta} that depend on redshift but are independent of scale. The intensity fluctuations introduce a scale dependence in both b_{\\delta} and {\\beta}, but keeping their product b_{\\delta}{\\beta} fixed. Observations of the Ly{\\alpha} correlations and cross-correlations with radiation sources like those being done at present in the BOSS survey of SDSS-III (Busca et al. 2013; Slosar et al. 2013; Font-Ribera et al. 2014) have the potential to measure this scale dependence, which reflects the biasing properties of the sources and absorbers of the ionising backgr...

  13. The energy and momentum input of supernova explosions in structured and ionised molecular clouds

    CERN Document Server

    Walch, S K

    2014-01-01

    We investigate the early impact of single and binary supernova (SN) explosions on dense gas clouds with three-dimensional, high-resolution, hydrodynamic simulations. The effect of cloud structure, radiative cooling, and ionising radiation from the progenitor stars on the net input of kinetic energy, f_kin=E_kin/E_SN, thermal energy, f_therm=E_therm/E_SN, and gas momentum f_P=P/P_SN to the interstellar medium (ISM) is tested. For clouds with n=100 cm^{-3}, the momentum generating Sedov and pressure-driven snowplough phases are terminated early (~ 0.01 Myr) and radiative cooling limits the coupling to f_therm ~ 0.01, f_kin ~ 0.05, and f_P ~ 9, significantly lower than for the case without cooling. For pre-ionised clouds these numbers are only increased by ~ 50%, independent of the cloud structure. This only suffices to accelerate ~ 5% of the cloud to radial velocities >30km/s. A second SN might further enhance the coupling efficiencies if delayed past the Sedov phase of the first explosion. Such very low coupli...

  14. Kinematically complete study on electron impact ionisation of aligned hydrogen molecules

    Energy Technology Data Exchange (ETDEWEB)

    Senftleben, Arne

    2009-10-28

    Within the work presented here, single ionisation of spatially aligned hydrogen molecules by 200 eV electrons was studied in a kinematically complete experiment. For the first time, a comprehensive set of fully differential cross sections (FDCS) was obtained for this process on a molecular target. The direction of the internuclear axis was derived from the fragment emission of post-collision dissociation of the residual H{sub 2}{sup +} ion. Therefore, a protonic fragment was detected in coincidence with the two final-state electrons using a dedicated reaction microscope and sophisticated data analysis. For direct ionisation into the ionic ground state, existing theoretical cross sections for aligned molecules were tested. Additionally, we observed molecular frame angular distributions of Auger electrons emitted through dissociative autoionisation of H{sub 2}. Earlier findings of kinematically incomplete experiments were reproduced, but the FDCS reveal structures so far unknown. Furthermore, for random alignment, differential cross sections at two distinct values of the mean internuclear distance were obtained, providing new arguments in the current discussion on the nature of discrepancies observed between atomic and molecular collisions. (orig.)

  15. Towards a Symmetric Momentum Distribution in the Muon Ionisation Cooling Experiment

    CERN Document Server

    Hansen, O M; Efthymiopoulos, I

    2013-01-01

    TheMuon Ionisation Cooling Experiment (MICE) is under development at Rutherford Appleton Labratory (UK). It is a proof-of-principle experiment for ionisation cooling, which is a prerequisite for a future Neutrino Factory (NF) or a Muon Collider. The muon beam will have a symmetrical momentum distribution in the cooling channel of theNF [1]. In the MICE beamline pions are captured by a quadrupole triplet, beam momentum is selected by dipole 1 (D1) before the beam traverses the decay solenoid. After the decay solenoid the beam momentum is selected by dipole 2 (D2), the beam is focused in two quadrupole triplets and characterised by time-of-flight (TOF) detectors TOF0 and TOF1 before entering the cooling channel. By doing a so-called D1-scan, where the optics parameters are scaled according to the upstream beam momentum, the purity and momentum distribution of the decay muons are changed. In this paper simulation results from G4Beamline (G4BL) [2] and data from MICE are presented and compared.

  16. Activity standardisation of (18)F and ionisation chamber calibration for nuclear medicine.

    Science.gov (United States)

    Schrader, H; Klein, R; Kossert, K

    2007-05-01

    Primary activity standardisations were performed on solutions of (18)F using 4pibeta-gamma coincidence counting and liquid scintillation counting (LSC) according to the CIEMAT/NIST method. A beta(+)-emission probability of 96.86% was used for both methods. The various standardised (18)F solutions were measured in ionisation chambers of the Physikalisch-Technische Bundesanstalt (PTB) and compared by determining radionuclide calibration factors. Already in 2001 an (18)F solution had been standardised at the PTB and compared with the results of nine national metrology institutes (NMIs), using the ISOCAL IV secondary radionuclide calibrators of the National Physical Laboratory (NPL) as transfer instruments and a (68)Ge check source solution. These results were linked to the International Reference System (SIR) at the Bureau International des Poids et Mesures (BIPM) by aliquots of solutions sent by the Laboratoire National Henri Becquerel (BNM-LNHB) and the NPL. Further on, in 2005, PTB sent an aliquot of an (18)F solution to the SIR for ionisation chamber measurements. A value of the equivalent activity was determined and included in the key comparison database (KCDB). The recent PTB value of the equivalent activity of the SIR is in good agreement with the key comparison reference value determined from five NMIs. These results confirm that the standardisation of (18)F solutions can be achieved with the accuracy required for use in nuclear medicine and, in particular, for applications in positron emission tomography (PET).

  17. Adaptive response to ionising radiation induced by cadmium in zebrafish embryos.

    Science.gov (United States)

    Choi, V W Y; Ng, C Y P; Kong, M K Y; Cheng, S H; Yu, K N

    2013-03-01

    An adaptive response is a biological response where the exposure of cells or animals to a low priming exposure induces mechanisms that protect the cells or animals against the detrimental effects of a subsequent larger challenging exposure. In realistic environmental situations, living organisms can be exposed to a mixture of stressors, and the resultant effects due to such exposures are referred to as multiple stressor effects. In the present work we demonstrated, via quantification of apoptosis in the embryos, that embryos of the zebrafish (Danio rerio) subjected to a priming exposure provided by one environmental stressor (cadmium in micromolar concentrations) could undergo an adaptive response against a subsequent challenging exposure provided by another environmental stressor (alpha particles). We concluded that zebrafish embryos treated with 1 to 10 μM Cd at 5 h postfertilisation (hpf) for both 1 and 5 h could undergo an adaptive response against subsequent ~4.4 mGy alpha-particle irradiation at 10 hpf, which could be interpreted as an antagonistic multiple stressor effect between Cd and ionising radiation. The zebrafish has become a popular vertebrate model for studying the in vivo response to ionising radiation. As such, our results suggested that multiple stressor effects should be carefully considered for human radiation risk assessment since the risk may be perturbed by another environmental stressor such as a heavy metal.

  18. Spectacular tails of ionised gas in the Virgo cluster galaxy NGC 4569

    CERN Document Server

    Boselli, A; Fossati, M; Boissier, S; Bomans, D; Consolandi, G; Anselmi, G; Cortese, L; Cote, P; Durrell, P; Ferrarese, L; Fumagalli, M; Gavazzi, G; Gwyn, S; Hensler, G; Sun, M; Toloba, E

    2016-01-01

    We obtained using MegaCam at the CFHT a deep narrow band Halpha+[NII] wide field image of NGC 4569, the brightest late-type galaxy in the Virgo cluster. The image reveals the presence of long tails of diffuse ionised gas without any associated stellar component extending from the disc of the galaxy up to ~ 80 kpc (projected distance) with a typical surface brightness of a few 10^-18 erg s-1 cm-2 arcsec-2. These features provide direct evidence that NGC 4569 is undergoing a ram presure stripping event. The image also shows a prominent 8 kpc spur of ionised gas associated to the nucleus that spectroscopic data identify as an outflow. With some assumptions on the 3D distribution of the gas, we use the Halpha surface brightness of these extended low surface brightness features to derive the density and the mass of the gas stripped during the interaction of the galaxy with the ICM. The comparison with ad-hoc chemo-spectrophotometric models of galaxy evolution indicates that the mass of the Halpha emitting gas in t...

  19. The effect of non ionising electromagnetic radiation on RAAF personnel during World War II.

    Science.gov (United States)

    Flaherty, J A

    1994-05-01

    Did exposure to non ionising electromagnetic radiation during World War II in the short term have a stimulating effect on the anterior pituitary gland, and in turn on the gonads of both sexes, since the figures obtained appeared to affect the sexes equally? Is it that the long-term effect of microwave radiation on personnel is to cause adenoma and carcinoma? Is this long-term effect similar to the long-term effect of X-rays on infants, children and adolescents? According to Harrison's Principles of Internal Medicine 1980 (page 1710): "X-rays to the head and neck in infancy, childhood or adolescence is associated with a high incidence of thyroid disease later in life. Nodular disease is found to be particularly common on 20% of patients at risk, and may not be apparent until 30 years or more after exposure. One-third of the nodular type are found to be carcinomatous." The effect of non ionising electromagnetic and microwave radiation on those who work in these fields certainly needs much more investigation. What will be the long-term effect of using micro-ovens on the rising generation?

  20. Occupational external exposure to ionising radiation in France (2005-2011).

    Science.gov (United States)

    Feuardent, J; Scanff, P; Crescini, D; Rannou, A

    2013-12-01

    The Institute for Radiological Protection and Nuclear Safety (IRSN) produces the French annual report on occupational exposure to ionising radiation, collecting all national data and aggregating the results according to a unique activity classification expected to be shared by all involved in personal dosimetric monitoring (employers, external dosimetry services and IRSN). Nearly 344,000 monitored workers were counted in France in 2011, with a collective dose of 64.24 man.Sv. The average annual dose (as calculated over the number of measurably exposed workers) differed among the main activity fields: 0.54 mSv in medical and veterinary activities, 1.18 mSv in the nuclear field, 1.60 mSv in non-nuclear industry and 0.47 mSv in research activities. Because of improved knowledge about worker activities, the results for year 2011 are detailed per activity sectors in each field. Lasting limitations prevent from having complete and reliable worker activity information. Solutions are considered to reduce the inaccuracy in the annually published statistics. The evolution of occupational external exposure to ionising radiation from 2005 to 2011 in France is then presented for the main activity fields.

  1. Innovative boron nitride-doped propellants

    Directory of Open Access Journals (Sweden)

    Thelma Manning

    2016-04-01

    Full Text Available The U.S. military has a need for more powerful propellants with balanced/stoichiometric amounts of fuel and oxidants. However, balanced and more powerful propellants lead to accelerated gun barrel erosion and markedly shortened useful barrel life. Boron nitride (BN is an interesting potential additive for propellants that could reduce gun wear effects in advanced propellants (US patent pending 2015-026P. Hexagonal boron nitride is a good lubricant that can provide wear resistance and lower flame temperatures for gun barrels. Further, boron can dope steel, which drastically improves its strength and wear resistance, and can block the formation of softer carbides. A scalable synthesis method for producing boron nitride nano-particles that can be readily dispersed into propellants has been developed. Even dispersion of the nano-particles in a double-base propellant has been demonstrated using a solvent-based processing approach. Stability of a composite propellant with the BN additive was verified. In this paper, results from propellant testing of boron nitride nano-composite propellants are presented, including closed bomb and wear and erosion testing. Detailed characterization of the erosion tester substrates before and after firing was obtained by electron microscopy, inductively coupled plasma and x-ray photoelectron spectroscopy. This promising boron nitride additive shows the ability to improve gun wear and erosion resistance without any destabilizing effects to the propellant. Potential applications could include less erosive propellants in propellant ammunition for large, medium and small diameter fire arms.

  2. Innovative boron nitride-doped propellants

    Institute of Scientific and Technical Information of China (English)

    Thelma MANNING; Henry GRAU; Paul MATTER; Michael BEACHY; Christopher HOLT; Samuel SOPOK; Richard FIELD; Kenneth KLINGAMAN; Michael FAIR; John BOLOGNINI; Robin CROWNOVER; Carlton P. ADAM; Viral PANCHAL; Eugene ROZUMOV

    2016-01-01

    The U.S. military has a need for more powerful propellants with balanced/stoichiometric amounts of fuel and oxidants. However, balanced and more powerful propellants lead to accelerated gun barrel erosion and markedly shortened useful barrel life. Boron nitride (BN) is an interesting potential additive for propellants that could reduce gun wear effects in advanced propellants (US patent pending 2015-026P). Hexagonal boron nitride is a good lubricant that can provide wear resistance and lower flame temperatures for gun barrels. Further, boron can dope steel, which drastically improves its strength and wear resistance, and can block the formation of softer carbides. A scalable synthesis method for producing boron nitride nano-particles that can be readily dispersed into propellants has been developed. Even dispersion of the nano-particles in a double-base propellant has been demonstrated using a solvent-based processing approach. Stability of a composite propellant with the BN additive was verified. In this paper, results from propellant testing of boron nitride nano-composite propellants are presented, including closed bomb and wear and erosion testing. Detailed characterization of the erosion tester substrates before and after firing was obtained by electron microscopy, inductively coupled plasma and x-ray photoelectron spectroscopy. This promising boron nitride additive shows the ability to improve gun wear and erosion resistance without any destabilizing effects to the propellant. Potential applications could include less erosive propellants in propellant ammunition for large, medium and small diameter fire arms.

  3. On magnetospheric electron impact ionisation and dynamics in Titan's ram-side and polar ionosphere – a Cassini case study

    Directory of Open Access Journals (Sweden)

    G. R. Lewis

    2007-11-01

    Full Text Available We present data from the sixth Cassini flyby of Titan (T5, showing that the magnetosphere of Saturn strongly interacts with the moon's ionosphere and exo-ionosphere. A simple electron ionisation model provides a reasonable agreement with the altitude structure of the ionosphere. Furthermore, we suggest that the dense and cold exo-ionosphere (from the exobase at 1430 km and outward to several Titan radii from the surface can be explained by magnetospheric forcing and other transport processes whereas exospheric ionisation by impacting low energy electrons seems to play a minor role.

  4. Collision strengths and transition probabilities for Co II infrared forbidden lines

    CERN Document Server

    Storey, P J; Sochi, Taha

    2016-01-01

    We calculate collision strengths and their thermally-averaged Maxwellian values for electron excitation and de-excitation between the fifteen lowest levels of singly-ionised cobalt, Co+, which give rise to emission lines in the near- and mid-infrared. Transition probabilities are also calculated and relative line intensities predicted for conditions typical of supernova ejecta. The diagnostic potential of the 10.52, 15.46 and 14.74 micro-metre transition lines is briefly discussed.

  5. Junctions between a boron nitride nanotube and a boron nitride sheet.

    Science.gov (United States)

    Baowan, Duangkamon; Cox, Barry J; Hill, James M

    2008-02-20

    For future nanoelectromechanical signalling devices, it is vital to understand how to connect various nanostructures. Since boron nitride nanostructures are believed to be good electronic materials, in this paper we elucidate the classification of defect geometries for combining boron nitride structures. Specifically, we determine possible joining structures between a boron nitride nanotube and a flat sheet of hexagonal boron nitride. Firstly, we determine the appropriate defect configurations on which the tube can be connected, given that the energetically favourable rings for boron nitride structures are rings with an even number of sides. A new formula E = 6+2J relating the number of edges E and the number of joining positions J is established for each defect, and the number of possible distinct defects is related to the so-called necklace and bracelet problems of combinatorial theory. Two least squares approaches, which involve variation in bond length and variation in bond angle, are employed to determine the perpendicular connection of both zigzag and armchair boron nitride nanotubes with a boron nitride sheet. Here, three boron nitride tubes, which are (3, 3), (6, 0) and (9, 0) tubes, are joined with the sheet, and Euler's theorem is used to verify geometrically that the connected structures are sound, and their relationship with the bonded potential energy function approach is discussed. For zigzag tubes (n,0), it is proved that such connections investigated here are possible only for n divisible by 3.

  6. The effect of boron deficiency on gene expression and boron compartmentalization in sugarbeet

    Science.gov (United States)

    NIP5, BOR1, NIP6, and WRKY6 genes were investigated for their role in boron deficiency in sugar beet, each with a proposed role in boron use in model plant species. All genes showed evidence of polymorphism in fragment size and gene expression in the target genomic DNA and cDNA libraries, with no co...

  7. Proceedings of workshop on 'boron science and boron neutron capture therapy'

    Energy Technology Data Exchange (ETDEWEB)

    Kitaoka, Y. [ed.

    1998-12-01

    This volume contains the abstracts and programs of the 8th (1996), 9th (1997) and 10th (1998) of the workshop on 'the Boron Science and Boron Neutron Capture Therapy' and the recent progress reports especially subscribed. The 11 of the presented papers are indexed individually. (J.P.N.)

  8. Spectromicroscopy of boron for the optimization of boron neutron capture therapy (BNCT) for cancer

    Science.gov (United States)

    Gilbert, B.; Redondo, J.; Baudat, P.-A.; Lorusso, G. F.; Andres, R.; Van Meir, E. G.; Brunet, J.-F.; Hamou, M.-F.; Suda, T.; Mercanti, Delio; Ciotti, M. Teresa; Droubay, T. C.; Tonner, B. P.; Perfetti, P.; Margaritondo, M.; DeStasio, Gelsomina

    1998-10-01

    We used synchrotron spectromicroscopy to study the microscopic distribution of boron in rat brain tumour and healthy tissue in the field of boron neutron capture therapy (BNCT). The success of this experimental cancer therapy depends on the preferential uptake of ? in tumour cells after injection of a boron compound (in our case ?, or BSH). With the Mephisto (microscope à emission de photoélectrons par illumination synchrotronique de type onduleur) spectromicroscope, high-magnification imaging and chemical analysis was performed on brain tissue sections from a rat carrying an implanted brain tumour and the results were compared with inductively coupled plasma-atomic emission spectroscopy (ICP-AES) detection of boron in bulk tissue. Boron was found to have been taken up more favourably by regions of tumour rather than healthy tissue, but the resulting boron distribution in the tumour was inhomogeneous. The results demonstrate that Mephisto can perform microchemical analysis of tissue sections, detect and localize the presence of boron with submicron spatial resolution. The application of this technique to boron in brain tissue can therefore be used to evaluate the current efforts to optimize BNC therapy.

  9. Spectromicroscopy of boron for the optimization of boron neutron capture therapy (BNCT) for cancer

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, B.; Redondo, J.; Baudat, P-A. [Institut de Physique Appliquee, Ecole Polytechnique Federale, Lausanne (Switzerland)] [and others

    1998-10-07

    We used synchrotron spectromicroscopy to study the microscopic distribution of boron in rat brain tumour and healthy tissue in the field of boron neutron capture therapy (BNCT). The success of this experimental cancer therapy depends on the preferential uptake of {sup 10}B in tumour cells after injection of a boron compound (in our case B{sub 12}H{sub 11}SH, or BSH). With the Mephisto (microscope a emission de photoelectrons par illumination synchrotronique de type onduleur) spectromicroscope, high-magnification imaging and chemical analysis was performed on brain tissue sections from a rat carrying an implanted brain tumour and the results were compared with inductively coupled plasma-atomic emission spectroscopy (ICP-AES) detection of boron in bulk tissue. Boron was found to have been taken up more favourably by regions of tumour rather than healthy tissue, but the resulting boron distribution in the tumour was inhomogeneous. The results demonstrate that Mephisto can perform microchemical analysis of tissue sections, detect and localize the presence of boron with submicron spatial resolution. The application of this technique to boron in brain tissue can therefore be used to evaluate the current efforts to optimize BNC therapy. (author)

  10. DABO Boronates: Stable Heterocyclic Boronic Acid Complexes for Use in Suzuki-Miyaura Cross-Coupling Reactions.

    Science.gov (United States)

    Reilly, Maureen K; Rychnovsky, Scott D

    2011-10-01

    Diethanolamine complexed heterocyclic boronic acids (DABO boronates) are air-stable reagents that can be used directly in Suzuki-Miyaura reactions in the presence of water or a protic co-solvent. Interestingly, heterocyclic DABO boronates can be stored for extended periods of time at room temperature with no noticeable degradation, unlike their boronic acid counterparts. Heterocyclic DABO boronates constitute an operationally simple and efficient alternative to other boronic acid derivatives as coupling partners in palladium catalyzed cross-coupling reactions under standard Suzuki-Miyaura conditions.

  11. Stark broadening of B IV spectral lines

    CERN Document Server

    Dimitrijevic, Milan S; Simic, Zoran; Kovacevic, Andjelka; Sahal-Brechot, Sylvie

    2016-01-01

    Stark broadening parameters for 157 multiplets of helium like boron (B IV) have been calculated using the impact semiclassical perturbation formalism. Obtained results have been used to investigate the regularities within spectral series. An example of the influence of Stark broadening on B IV lines in DO white dwarfs is given.

  12. A quantitative comparison between electrocoagulation and chemical coagulation for boron removal from boron-containing solution

    Energy Technology Data Exchange (ETDEWEB)

    Yilmaz, A. Erdem [Atatuerk University, Faculty of Engineering, Department of Environmental Engineering, 25240 Erzurum (Turkey)], E-mail: aerdemy@atauni.edu.tr; Boncukcuoglu, Recep [Atatuerk University, Faculty of Engineering, Department of Environmental Engineering, 25240 Erzurum (Turkey); Kocakerim, M. Muhtar [Atatuerk University, Faculty of Engineering, Department of Chemical Engineering, 25240 Erzurum (Turkey)

    2007-10-22

    This paper provides a quantitative comparison of electrocoagulation and chemical coagulation approaches based on boron removal. Electrocoagulation process delivers the coagulant in situ as the sacrificial anode corrodes, due to a fixed current density, while the simultaneous evolution of hydrogen at the cathode allows for pollutant removal by flotation. By comparison, conventional chemical coagulation typically adds a salt of the coagulant, with settling providing the primary pollutant removal path. Chemical coagulation was carried out via jar tests using aluminum chloride. Comparison was done with the same amount of coagulant between electrocoagulation and chemical coagulation processes. Boron removal obtained was higher with electrocoagulation process. In addition, it was seen that chemical coagulation has any effect for boron removal from boron-containing solution. At optimum conditions (e.g. pH 8.0 and aluminum dose of 7.45 g/L), boron removal efficiencies for electrocoagulation and chemical coagulation were 94.0% and 24.0%, respectively.

  13. A quantitative comparison between electrocoagulation and chemical coagulation for boron removal from boron-containing solution.

    Science.gov (United States)

    Yilmaz, A Erdem; Boncukcuoğlu, Recep; Kocakerim, M Muhtar

    2007-10-22

    This paper provides a quantitative comparison of electrocoagulation and chemical coagulation approaches based on boron removal. Electrocoagulation process delivers the coagulant in situ as the sacrificial anode corrodes, due to a fixed current density, while the simultaneous evolution of hydrogen at the cathode allows for pollutant removal by flotation. By comparison, conventional chemical coagulation typically adds a salt of the coagulant, with settling providing the primary pollutant removal path. Chemical coagulation was carried out via jar tests using aluminum chloride. Comparison was done with the same amount of coagulant between electrocoagulation and chemical coagulation processes. Boron removal obtained was higher with electrocoagulation process. In addition, it was seen that chemical coagulation has any effect for boron removal from boron-containing solution. At optimum conditions (e.g. pH 8.0 and aluminum dose of 7.45 g/L), boron removal efficiencies for electrocoagulation and chemical coagulation were 94.0% and 24.0%, respectively.

  14. Ceramic silicon-boron-carbon fibers from organic silicon-boron-polymers

    Science.gov (United States)

    Riccitiello, Salvatore R. (Inventor); Hsu, Ming-Ta S. (Inventor); Chen, Timothy S. (Inventor)

    1993-01-01

    Novel high strength ceramic fibers derived from boron, silicon, and carbon organic precursor polymers are discussed. The ceramic fibers are thermally stable up to and beyond 1200 C in air. The method of preparation of the boron-silicon-carbon fibers from a low oxygen content organosilicon boron precursor polymer of the general formula Si(R2)BR(sup 1) includes melt-spinning, crosslinking, and pyrolysis. Specifically, the crosslinked (or cured) precursor organic polymer fibers do not melt or deform during pyrolysis to form the silicon-boron-carbon ceramic fiber. These novel silicon-boron-carbon ceramic fibers are useful in high temperature applications because they retain tensile and other properties up to 1200 C, from 1200 to 1300 C, and in some cases higher than 1300 C.

  15. Atmospheric contribution to boron enrichment in aboveground wheat tissues.

    Science.gov (United States)

    Wang, Cheng; Ji, Junfeng; Chen, Mindong; Zhong, Cong; Yang, Zhongfang; Browne, Patrick

    2017-05-01

    Boron is an essential trace element for all organisms and has both beneficial and harmful biological functions. A particular amount of boron is discharged into the environment every year because of industrial activities; however, the effects of environmental boron emissions on boron accumulation in cereals has not yet been estimated. The present study characterized the accumulation of boron in wheat under different ecological conditions in the Yangtze River Delta (YRD) area. This study aimed to estimate the effects of atmospheric boron that is associated with industrial activities on boron accumulation in wheat. The results showed that the concentrations of boron in aboveground wheat tissues from the highly industrialized region were significantly higher than those from the agriculture-dominated region, even though there was no significant difference in boron content in soils. Using the model based on the translocation coefficients of boron in the soil-wheat system, we estimated that the contribution of atmosphere to boron accumulation in wheat straw in the highly industrialized region exceeded that in the agriculture-dominated region by 36%. In addition, from the environmental implication of the model, it was estimated that the development of boron-utilizing industries had elevated the concentration of boron in aboveground wheat tissues by 28-53%. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Thermoluminescent properties of CVD diamond: applications to ionising radiation dosimetry; Proprietes thermoluminescentes du diamant CVD: applications a la dosimetrie des rayonnements ionisants

    Energy Technology Data Exchange (ETDEWEB)

    Petitfils, A

    2007-09-15

    Remarkable properties of synthetic diamond (human soft tissue equivalence, chemical stability, non-toxicity) make this material suitable for medical application as thermoluminescent dosimeter (TLD). This work highlights the interest of this material as radiotherapy TLD. In the first stage of this work, we looked after thermoluminescent (TL) and dosimetric properties of polycrystalline diamond made by Chemically Vapor Deposited (CVD) synthesis. Dosimetric characteristics are satisfactory as TLD for medical application. Luminescence thermal quenching on diamond has been investigated. This phenomenon leads to a decrease of dosimetric TL peak sensitivity when the heating rate increases. The second part of this work analyses the use of synthetic diamond as TLD in radiotherapy. Dose profiles, depth dose distributions and the cartography of an electron beam obtained with our samples are in very good agreement with results from an ionisation chamber. It is clearly shown that CVD) diamond is of interest to check beams of treatment accelerators. The use of these samples in a control of treatment with Intensity Modulated Radiation Therapy underlines good response of synthetic diamond in high dose gradient areas. These results indicate that CVD diamond is a promising material for radiotherapy dosimetry. (author)

  17. Study and optimization of the ionisation channel in the Edelweiss dark matter direct detection experiment; Etude et optimisation de la voie ionisation dans l'experience Edelweiss de detection directe de la matiere noire

    Energy Technology Data Exchange (ETDEWEB)

    Censier, B

    2006-02-15

    The EDELWEISS experiment is aiming at the detection of Weakly Interactive Massive Particles (WIMPs), today's most favoured candidates for solving the dark matter issue. Background ionising particles are identified thanks to the simultaneous measurement of heat and ionisation in the detectors. The main limitation to this method is coming from the ionisation measurement, charge collection being less efficient in some part of the detectors known as 'dead' areas. The specificity of the measurement is due to the use of very low temperatures and low collection fields. This thesis is dedicated to the study of carrier trapping. It involves time-resolved charge measurements as well as a simulation code adapted to the specific physical conditions. We first present results concerning charge trapping at the free surfaces of the detectors. Our method allows to build a surface-charge in a controlled manner by irradiation with a strong radioactive source. This charge is then characterised with a weaker source which acts as a probe. In a second part of the work, bulk-trapping characteristics are deduced from charge collection efficiency measurements, and by an original method based on event localisation in the detector. The results show that a large proportion of the doping impurities are ionised, as indicated independently by the study of degradation by space-charge build-up. In this last part, near-electrodes areas are found to contain large densities of charged trapping centres, in connection with dead-layer effects. (author)

  18. Quantifying the pH ‘vital effect’ in the temperate zooxanthellate coral Cladocora caespitosa: Validation of the boron seawater pH proxy

    Science.gov (United States)

    Trotter, Julie; Montagna, Paolo; McCulloch, Malcolm; Silenzi, Sergio; Reynaud, Stéphanie; Mortimer, Graham; Martin, Sophie; Ferrier-Pagès, Christine; Gattuso, Jean-Pierre; Rodolfo-Metalpa, Riccardo

    2011-03-01

    Boron isotopic and elemental systematics are used to define the vital effects for the temperate shallow water Mediterranean coral Cladocora caespitosa. The corals are from a range of seawater pH conditions (pHT ~ 7.6 to ~ 8.1) and environmental settings: (1) naturally living colonies harvested from normal pH waters offshore Levanto, (2) colonies transplanted nearby a subsea volcanic vent system, and (3) corals cultured in aquaria exposed to high (700 μatm) and near present day (400 μatm) pCO2 levels. B/Ca compositions measured using laser ablation inductively coupled mass spectrometry (LA-ICPMS) show that boron uptake by C. caespitosa cultured at different pCO2 levels is independent of ambient seawater pH being mainly controlled by temperature-dependent calcification. In contrast, the boron isotope compositions (δ11Bcarb) of the full suite of corals determined by positive thermal ionisation mass spectrometry (PTIMS) shows a clear trend of decreasing δ11Bcarb (from 26.7 to 22.2‰) with decreasing seawater pH, reflecting the strong pH dependence of the boron isotope system. The δ11Bcarb compositions together with measurements of ambient seawater parameters enable calibration of the boron pH proxy for C. caespitosa, by using a new approach that defines the relationship between ambient seawater pH (pHsw) and the internally controlled pH at the site of calcification (pHbiol). C. caespitosa exhibits a linear relationship between pHsw and the shift in pH due to physiological processes (ΔpH = pHbiol - pHsw) giving the regression ΔpHClad = 4.80 - 0.52 × pHsw for this species. We further apply this method (“ΔpH-pHsw”) to calibrate tropical species of Porites, Acropora, and Stylophora reported in the literature. The temperate and tropical species calibrations are all linearly correlated (r2 > 0.9) and the biological fractionation component (ΔpH) between species varies within ~ 0.2 pH units. Our “ΔpH-pHsw” approach provides a robust and accurate tool to

  19. Boron remobilization at low boron supply in olive (Olea europaea) in relation to leaf and phloem mannitol concentrations.

    Science.gov (United States)

    Liakopoulos, Georgios; Stavrianakou, Sotiria; Filippou, Manolis; Fasseas, Costas; Tsadilas, Christos; Drossopoulos, Ioannis; Karabourniotis, George

    2005-02-01

    For plant species in which a considerable portion of the photoassimilates are translocated in the phloem as sugar alcohols, boron is freely translocated from mature organs to growing tissues. However, the effects of decreased plant boron status on boron remobilization are poorly understood. We conducted a growth chamber experiment (CE) and a field experiment (FE) to study the effects of low boron supply on boron remobilization in olive (Olea europaea L.), a species that transports considerable amounts of mannitol in the phloem. For the CE, several physiological parameters were compared between control (B+) and boron-deficient olive plants (B-) during the expansion of new leaves. Boron remobilization was assessed by measuring boron content of selected leaves at the beginning and at the end of the CE. As expected, boron was remobilized from mature leaves to young leaves of B+ plants; however, considerable boron remobilization was also observed in B- plants, suggesting a mechanism whereby olive can sustain a minimum boron supply for growth of new tissues despite an insufficient external boron supply. Boron deficiency caused inhibition of new growth but had no effect on photosynthetic capacity per unit leaf surface area of young and mature leaves, thereby altering the carbon utilization pattern and resulting in carbon allocation to structures within the source leaves and accumulation of soluble carbohydrates. Specifically, in mature B- leaves in the CE and in B- leaves in the FE, mannitol concentration on a leaf water content basis increased by 48 and 27% respectively, compared with controls. Carbon export ability (assessed by both phloem anatomy and phloem exudate composition of FE leaves) was enhanced at low boron supply. We conclude that, at low boron supply, increased mannitol concentrations maintain boron remobilization from source leaves to boron-demanding sink leaves.

  20. Multidisciplinary approach to assess the sensitivity of dwarf tomato plants to low-LET ionising radiation

    Science.gov (United States)

    De Micco, Veronica; De Pascale, Stefania; Aronne, Giovanna; Paradiso, Roberta; Vitaglione, Paola; Turano, Mimmo; Arena, Carmen

    Ionising radiation, acting alone or in interaction with microgravity and other environmental constraints, may affect plant at molecular, morpho-structural and physiological level. The intensity of the plant’s response depends on the properties of radiation and on the features of the plant itself. Indeed, different species are characterised by different susceptibility to radiation which may change during the life course. The aim of this research was to study the radiosensitivity to low-LET ionising radiation of plants of dwarf tomato (Solanum lycopersicum L. ‘Microtom’) at two phenological phases (vegetative and reproductive), within the purpose of analysing plants for consideration as candidates for Bioregenerative Life Support Systems (BLSS) in Space. To pursue this objective, plants of the cultivar Microtom were irradiated with different doses of X-rays either at the stage of the second true leaf (VP - vegetative phase) or when at least one flower was blossomed (RP - reproductive phase). Plant’s response to ionising radiation was assessed through a multidisciplinary approach combining genetic analyses, ecophysiological measurements, morpho-anatomical characterisation of leaves and fruits, nutritional analyses of fruits. Growth, molecular and morpho-functional traits were measured during plant development up to fruiting in both VP and RP plant groups, and compared with non-irradiated control plants. Plant growth was monitored weekly recording parameters such as plant height, number of leaves, leaf area, flowering and fruiting rate. Potential DNA alterations were explored through Random Amplified Polymorphic DNA (RAPD) technique. The efficiency of the photosynthetic apparatus was evaluated by determining photosynthetic pigment composition, photochemistry and leaf gas exchanges. Leaf and fruit structure were analysed through light and epi-fluorescence microscopy. Leaf anatomical traits related to photosynthetic efficiency, and to structural radioprotection

  1. Method of manufacture of atomically thin boron nitride

    Science.gov (United States)

    Zettl, Alexander K

    2013-08-06

    The present invention provides a method of fabricating at least one single layer hexagonal boron nitride (h-BN). In an exemplary embodiment, the method includes (1) suspending at least one multilayer boron nitride across a gap of a support structure and (2) performing a reactive ion etch upon the multilayer boron nitride to produce the single layer hexagonal boron nitride suspended across the gap of the support structure. The present invention also provides a method of fabricating single layer hexagonal boron nitride. In an exemplary embodiment, the method includes (1) providing multilayer boron nitride suspended across a gap of a support structure and (2) performing a reactive ion etch upon the multilayer boron nitride to produce the single layer hexagonal boron nitride suspended across the gap of the support structure.

  2. Studies on Separation Process and Production Technology of Boron Isotope

    Directory of Open Access Journals (Sweden)

    LI Jian-ping

    2014-02-01

    Full Text Available The boron isotopes separation test was performed by chemical exchange reaction in the benzene ether -three boron fluoride system, which resulted to the boron isotopic enrichment of -10 in the liquid phase, the boron isotopic enrichment of -11 in the gas phase. After then, boron isotope separation trial production has been finished. In this process, the exchange column and complex tower normal operating parameters and the complex tower technology have been obtained, the problems of material distillation purification is solved, boron isotopes feasibility with PTFE packing enrichment is verified in an exchange column. Also, effect of operating pressure, flow and other parameters on boron -10 isotopic enrichment experiments and the effect and properties of the PTFE packing have been investigated in the existing system. All the results are very useful for the industrialization of the boron isotopes separation system.

  3. Enhanced Boron Tolerance in Plants Mediated by Bidirectional Transport Through Plasma Membrane Intrinsic Proteins.

    Science.gov (United States)

    Mosa, Kareem A; Kumar, Kundan; Chhikara, Sudesh; Musante, Craig; White, Jason C; Dhankher, Om Parkash

    2016-02-23

    High boron (B) concentration is toxic to plants that limit plant productivity. Recent studies have shown the involvement of the members of major intrinsic protein (MIP) family in controlling B transport. Here, we have provided experimental evidences showing the bidirectional transport activity of rice OsPIP1;3 and OsPIP2;6. Boron transport ability of OsPIP1;3 and OsPIP2;6 were displayed in yeast HD9 mutant strain (∆fps1∆acr3∆ycf1) as a result of increased B sensitivity, influx and accumulation by OsPIP1;3, and rapid efflux activity by OsPIP2;6. RT-PCR analysis showed strong upregulation of OsPIP1;3 and OsPIP2;6 transcripts in roots by B toxicity. Transgenic Arabidopsis lines overexpressing OsPIP1;3 and OsPIP2;6 exhibited enhanced tolerance to B toxicity. Furthermore, B concentration was significantly increased after 2 and 3 hours of tracer boron ((10)B) treatment. Interestingly, a rapid efflux of (10)B from the roots of the transgenic plants was observed within 1 h of (10)B treatment. Boron tolerance in OsPIP1;3 and OsPIP2;6 lines was inhibited by aquaporin inhibitors, silver nitrate and sodium azide. Our data proved that OsPIP1;3 and OsPIP2;6 are indeed involved in both influx and efflux of boron transport. Manipulation of these PIPs could be highly useful in improving B tolerance in crops grown in high B containing soils.

  4. ESR-dosimetry in thermal and epithermal neutron fields for application in boron neutron capture therapy

    Energy Technology Data Exchange (ETDEWEB)

    Schmitz, Tobias

    2016-01-22

    Dosimetry is essential for every form of radiotherapy. In Boron Neutron Capture Therapy (BNCT) mixed neutron and gamma fields have to be considered. Dose is deposited in different neutron interactions with elements in the penetrated tissue and by gamma particles, which are always part of a neutron field. The therapeutic dose in BNCT is deposited by densely ionising particles, originating from the fragmentation of the isotope boron-10 after capture of a thermal neutron. Despite being investigated for decades, dosimetry in neutron beams or fields for BNCT remains complex, due to the variety in type and energy of the secondary particles. Today usually ionisation chambers combined with metal foils are used. The applied techniques require extensive effort and are time consuming, while the resulting uncertainties remain high. Consequently, the investigation of more effective techniques or alternative dosimeters is an important field of research. In this work the possibilities of ESR-dosimeters in those fields have been investigated. Certain materials, such as alanine, generate stable radicals upon irradiation. Using Electron Spin Resonance (ESR) spectrometry the amount of radicals, which is proportional to absorbed dose, can be quantified. Different ESR detector materials have been irradiated in the thermal neutron field of the research reactor TRIGA research reactor in Mainz, Germany, with five setups, generating different secondary particle spectra. Further irradiations have been conducted in two epithermal neutron beams. The detector response, however, strongly depends on the dose depositing particle type and energy. It is hence necessary to accompany measurements by computational modelling and simulation. In this work the Monte Carlo code FLUKA was used to calculate absorbed doses and dose components. The relative effectiveness (RE), linking absorbed dose and detector response, has been calculated using amorphous track models. For the simulation, detailed models of

  5. Characterisation of exposure to non-ionising electromagnetic fields in the Spanish INMA birth cohort: Study protocol

    NARCIS (Netherlands)

    M. Gallastegi (Mara); M. Guxens (Mònica ); A. Jiménez-Zabala (Ana); I. Calvente (Irene); M. Fernández (Marta); L. Birks (Laura); B. Struchen (Benjamin); M. Vrijheid (Martine); M. Estarlich (Marisa); M.F. Fernandez (Mariana); M. Torrent (Maties); F. Ballester (Ferran); J.J. Aurrekoetxea (Juan José); J. Ibarluzea (Jesús); D. Guerra (David); J. González (Julián); M. Röösli (Martin); L. Santa-Marina (Loreto)

    2016-01-01

    textabstractBackground: Analysis of the association between exposure to electromagnetic fields of non-ionising radiation (EMF-NIR) and health in children and adolescents is hindered by the limited availability of data, mainly due to the difficulties on the exposure assessment. This study protocol de

  6. Brain Radiation Information Data Exchange (BRIDE): Integration of experimental data from low-dose ionising radiation research for pathway discovery

    NARCIS (Netherlands)

    C. Karapiperis (Christos); S.J. Kempf (Stefan J.); R. Quintens (Roel); O. Azimzadeh (Omid); V.L. Vidal (Victoria Linares); S. Pazzaglia; D. Bazyka (Dimitry); P.G. Mastroberardino (Pier); Z.G. Scouras (Zacharias G.); S. Tapio (Soile); M.A. Benotmane (Mohammed Abderrafi); C.A. Ouzounis (Christos A.)

    2016-01-01

    textabstractBackground: The underlying molecular processes representing stress responses to low-dose ionising radiation (LDIR) in mammals are just beginning to be understood. In particular, LDIR effects on the brain and their possible association with neurodegenerative disease are currently being ex

  7. On the ionisation fraction in protoplanetary disks III. The effect of X-ray flares on gas-phase chemistry

    CERN Document Server

    Ilgner, M; Ilgner, Martin; Nelson, Richard P.

    2006-01-01

    Context. Recent observations of the X-ray emission from T Tauri stars in the Orion nebula have shown that they undergo frequent outbursts in their X-ray luminosity. These X-ray flares are characterised by increases in luminosity by two orders of magnitude, a typical duration of less than one day, and a significant hardening of the X-ray spectrum. Aims. It is unknown what effect these X-ray flares will have on the ionisation fraction and dead-zone structure in protoplanetary disks. We present the results of calculations designed to address this question. Methods. We have performed calculations of the ionisation fraction in a standard $\\alpha$-disk model using two different chemical reaction networks. We include in our models ionisation due to X-rays from the central star, and calculate the time-dependent ionisation fraction and dead--zone structure for the inner 10 AU of a protoplanetary disk model. Results. We find that the disk response to X-ray flares depends on whether the plasma temperature increases duri...

  8. Comparison of quantification methods for the analysis of polychlorinated alkanes using electron capture negative ionisation mass spectrometry

    NARCIS (Netherlands)

    Rusina, T.; Korytar, P.; Boer, de J.

    2011-01-01

    Four quantification methods for short-chain chlorinated paraffins (SCCPs) or polychlorinated alkanes (PCAs) using gas chromatography electron capture negative ionisation low resolution mass spectrometry (GC-ECNI-LRMS) were investigated. The method based on visual comparison of congener group pattern

  9. Determination of kava lactones in food supplements by liquid chromatography-atmospheric pressure chemical ionisation tandem mass spectrometry

    NARCIS (Netherlands)

    Bobeldijk, I.; Boonzaaijer, G.; Spies-Faber, E.J.; Vaes, W.H.J.

    2005-01-01

    Reversed-phase liquid chromatography and detection with atmospheric pressure chemical ionisation tandem mass spectrometry was used for the determination of kava extracts in herbal mixtures. One percent of kava extract can be detected, corresponding to approximately 0.05-0.2 mg/g of the individual ka

  10. Time-dependent hydrogen ionisation in 3D simulations of the solar chromosphere. Methods and first results

    NARCIS (Netherlands)

    Leenaarts, J.; Wedemeyer-Bohm, S.

    2006-01-01

    Context. The hydrogen ionisation degree deviates substantially from statistical equilibrium under the conditions of the solar chromosphere. A realistic description of this atmospheric layer thus must account for time-dependent non-equilibrium effects. Aims. Advancing the realism of numerical simulat

  11. Characterisation of exposure to non-ionising electromagnetic fields in the Spanish INMA birth cohort: Study protocol

    NARCIS (Netherlands)

    M. Gallastegi (Mara); M. Guxens (Mònica ); A. Jiménez-Zabala (Ana); I. Calvente (Irene); M. Fernández (Marta); L. Birks (Laura); B. Struchen (Benjamin); M. Vrijheid (Martine); M. Estarlich (Marisa); M.F. Fernandez (Mariana); M. Torrent (Maties); F. Ballester (Ferran); J.J. Aurrekoetxea (Juan José); J. Ibarluzea (Jesús); D. Guerra (David); J. González (Julián); M. Röösli (Martin); L. Santa-Marina (Loreto)

    2016-01-01

    textabstractBackground: Analysis of the association between exposure to electromagnetic fields of non-ionising radiation (EMF-NIR) and health in children and adolescents is hindered by the limited availability of data, mainly due to the difficulties on the exposure assessment. This study protocol

  12. Brain Radiation Information Data Exchange (BRIDE): Integration of experimental data from low-dose ionising radiation research for pathway discovery

    NARCIS (Netherlands)

    C. Karapiperis (Christos); S.J. Kempf (Stefan J.); R. Quintens (Roel); O. Azimzadeh (Omid); V.L. Vidal (Victoria Linares); S. Pazzaglia; D. Bazyka (Dimitry); P.G. Mastroberardino (Pier); Z.G. Scouras (Zacharias G.); S. Tapio (Soile); M.A. Benotmane (Mohammed Abderrafi); C.A. Ouzounis (Christos A.)

    2016-01-01

    textabstractBackground: The underlying molecular processes representing stress responses to low-dose ionising radiation (LDIR) in mammals are just beginning to be understood. In particular, LDIR effects on the brain and their possible association with neurodegenerative disease are currently being

  13. Spin-Orbit Larmor Clock for Ionisation Times in One-Photon and Strong-Field Regimes

    CERN Document Server

    Kaushal, Jivesh; Torlina, Lisa; Ivanov, Misha; Smirnova, Olga

    2015-01-01

    Photoionisation is a process where absorption of one or several photons liberates an electron and creates a hole in a quantum system, such as an atom or a molecule. Is it faster to remove an electron using one or many photons, and how to define this time? Here we introduce a clock that allows us to define ionisation time for both one-photon and many-photon ionisation regimes. The clock uses the interaction of the electron or hole spin with the magnetic field created by their orbital motion, known as the spin-orbit interaction. The angle of spin precession in the magnetic field records time. We use the combination of analytical theory and ab-initio calculations to show how ionisation delay depends on the number of absorbed photons, how it appears in the experiment and what electron dynamics it signifies. In particular, we apply our method to calculate the derived time delays in tunnelling regime of strong-field ionisation.

  14. Boron neutron capture therapy in cancer: past, present and future

    Energy Technology Data Exchange (ETDEWEB)

    Pisarev, Mario A.; Dagrosa, Maria Alejandra; Juvenal, Guilermo J. [National Atomic Energy Commission, Buenos Aires (Argentina). Div. of Nuclear Biochemistry; University of Buenos Aires (Argentina). School of Medicine. Dept. of Human Biochemistry

    2007-07-15

    Undifferentiated thyroid cancer (UTC) is a very aggressive tumor with no effective treatment, since it lacks iodine uptake and does not respond to radio or chemotherapy. The prognosis of these patients is bad, due to the rapid growth of the tumor and the early development of metastasis. Boron neutron capture therapy (BNCT) is based on the selective uptake of certain boron non-radioactive compounds by a tumor, and the subsequent irradiation of the area with an appropriate neutron beam. {sup 10}B is then activated to {sup 11}B, which will immediately decay releasing alpha particles and {sup 7}Li, of high linear energy transfer (LET) and limited reach. Clinical trials are being performed in patients with glioblastoma multiform and melanoma. We have explored its possible application to UTC. Our results demonstrated that a cell line of human UTC has a selective uptake of borophenylalanine (BPA) both in vitro and after transplantation to nude mice. Treatment of mice by BNCT led to a complete control of growth and cure of 100% of the animals. Moreover dogs with spontaneous UTC also have a selective uptake of BPA. At the present we are studying the biodistribution of BPA in patients with UTC before its application in humans. (author)

  15. Electron spin relaxation of a boron-containing heterocyclic radical

    Science.gov (United States)

    Eaton, Sandra S.; Huber, Kirby; Elajaili, Hanan; McPeak, Joseph; Eaton, Gareth R.; Longobardi, Lauren E.; Stephan, Douglas W.

    2017-03-01

    Preparation of the stable boron-containing heterocyclic phenanthrenedione radical, (C6F5)2B(O2C14H8), by frustrated Lewis pair chemistry has been reported recently. Electron paramagnetic resonance measurements of this radical were made at X-band in toluene:dichloromethane (9:1) from 10 to 293 K, in toluene from 180 to 293 K and at Q-band at 80 K. In well-deoxygenated 0.1 mM toluene solution at room temperature hyperfine splittings from 11B, four pairs of 1H, and 5 pairs of 19F contribute to an EPR spectrum with many resolved lines. Observed hyperfine couplings were assigned based on DFT calculations and account for all of the fluorines and protons in the molecule. Rigid lattice g values are gx = 2.0053, gy = 2.0044, and gz = 2.0028. Near the melting point of the solvent 1/Tm is enhanced due to motional averaging of g and A anisotropy. Increasing motion above the melting point enhances 1/T1 due to contributions from tumbling-dependent processes. The overall temperature dependence of 1/T1 from 10 to 293 K was modeled with the sum of contributions of a process that is linear in T, a Raman process, spin rotation, and modulation of g anisotropy by molecular tumbling. The EPR measurements are consistent with the description of this compound as a substituted aromatic radical, with relatively small spin density on the boron.

  16. Characterization of boron carbide with an electron microprobe

    Science.gov (United States)

    Matteudi, G.; Ruste, J.

    1983-01-01

    Within the framework of a study of heterogeneous materials (Matteudi et al., 1971: Matteudi and Verchery, 1972) thin deposits of boron carbide were characterized. Experiments using an electronic probe microanalyzer to analyze solid boron carbide or boron carbide in the form of thick deposits are described. Quantitative results on boron and carbon are very close to those obtained when applying the Monte Carlo-type correction calculations.

  17. The KMOS AGN Survey at High redshift (KASHz): the prevalence and drivers of ionised outflows in the host galaxies of X-ray AGN

    CERN Document Server

    Harrison, C M; Mullaney, J R; Stott, J P; Swinbank, A M; Arumugam, V; Bauer, F E; Bower, R G; Bunker, A J; Sharples, R M

    2015-01-01

    We present the first results from the KMOS AGN Survey at High redshift (KASHz), a VLT/KMOS integral-field spectroscopic survey of z>0.6 AGN. We present galaxy-integrated spectra of 89 X-ray AGN (Lx=10^42-10^45 erg/s), for which we observed [O III] (z=1.1-1.7) or Halpha emission (z=0.6-1.1). The targets have X-ray luminosities representative of the parent AGN population and we explore the emission-line luminosities as a function of X-ray luminosity. For the [O III] targets, ~50 per cent have ionised gas velocities indicative of gas that is dominated by outflows and/or highly turbulent material (i.e., overall line-widths >~600 km/s). The most luminous half (i.e., Lx>6x10^43 erg/s) have a >~2 times higher incidence of such velocities. On the basis of our results, we find no evidence that X-ray obscured AGN are more likely to host extreme kinematics than unobscured AGN. Our KASHz sample has a distribution of gas velocities that is consistent with a luminosity-matched sample of z<0.4 AGN. This implies little ev...

  18. Boron Removal in Seawater Reverse Osmosis System

    KAUST Repository

    Rahmawati, Karina

    2011-07-01

    Reverse osmosis successfully proves to remove more than 99% of solute in seawater, providing fresh water supply with satisfied quality. Due to some operational constraints, however, some trace contaminants removal, such as boron, cannot be achieved in one pass system. The stringent criterion for boron from World Health Organization (WHO) and Saudi Arabia local standard (0.5 mg/l) is hardly fulfilled by single pass sea water reverse osmosis (SWRO) plants. Some design processes have been proposed to deal with boron removal, but they are not economically efficient due to high energy and chemical consumption. The objective of this study was to study boron removal by different reverse osmosis membranes in two pH conditions, with and without antiscalant addition. Thus, it was expected to observe the possibility of operating single pass system and necessity to operate two pass system using low energy membrane. Five membrane samples were obtained from two different manufacturers. Three types of feed water pH were used, pH 8, pH 10, and pH 10 with antiscalant addition. Experiment was conducted in parallel to compare membrane performance from two manufacturers. Filtration was run with fully recycle mode for three days. Sample of permeate and feed were taken every 12 hours, and analyzed for their boron and TDS concentration. Membrane samples were also tested for their surface charge. The results showed that boron rejection increases as the feed pH increases. This was caused by dissociation of boric acid to negatively charged borate ion and more negatively charged membrane surface at elevated pH which enhance boron rejection. This study found that single pass reverse osmosis system, with and without elevating the pH, may not be possible to be applied because of two reasons. First, permeate quality in term of boron, does not fulfill WHO and local Saudi Arabia regulations. Second, severe scaling occurs due to operation in alkaline condition, since Ca and Mg concentration are

  19. Ionisation in turbulent magnetic molecular clouds. I. Effect on density and mass-to-flux ratio structures

    Science.gov (United States)

    Bailey, Nicole D.; Basu, Shantanu; Caselli, Paola

    2017-05-01

    Context. Previous studies show that the physical structures and kinematics of a region depend significantly on the ionisation fraction. These studies have only considered these effects in non-ideal magnetohydrodynamic simulations with microturbulence. The next logical step is to explore the effects of turbulence on ionised magnetic molecular clouds and then compare model predictions with observations to assess the importance of turbulence in the dynamical evolution of molecular clouds. Aims: In this paper, we extend our previous studies of the effect of ionisation fractions on star formation to clouds that include both non-ideal magnetohydrodynamics and turbulence. We aim to quantify the importance of a treatment of the ionisation fraction in turbulent magnetised media and investigate the effect of the turbulence on shaping the clouds and filaments before star formation sets in. In particular, here we investigate how the structure, mass and width of filamentary structures depend on the amount of turbulence in ionised media and the initial mass-to-flux ratio. Methods: To determine the effects of turbulence and mass-to-flux ratio on the evolution of non-ideal magnetised clouds with varying ionisation profiles, we have run two sets of simulations. The first set assumes different initial turbulent Mach values for a fixed initial mass-to-flux ratio. The second set assumes different initial mass-to-flux ratio values for a fixed initial turbulent Mach number. Both sets explore the effect of using one of two ionisation profiles: step-like (SL) or cosmic ray only (CR-only). We compare the resulting density and mass-to-flux ratio structures both qualitatively and quantitatively via filament and core masses and filament fitting techniques (Gaussian and Plummer profiles). Results: We find that even with almost no turbulence, filamentary structure still exists although at lower density contours. Comparison of simulations shows that for turbulent Mach numbers above 2, there is

  20. INFLUENCE OF FINE-DISPERSED BORON CARBIDE ON THE STRUCTURE AND CHARACTERISTICS OF IRON-BORON ALLOY

    Directory of Open Access Journals (Sweden)

    N. F. Nevar

    2010-01-01

    Full Text Available The influence of boron carbide as fine-dispersed material input into the melt on structure morphology, founding, technological and exploitation characterisstics of cast iron-boron material is shown.

  1. Update on human health effects of boron.

    Science.gov (United States)

    Nielsen, Forrest H

    2014-10-01

    In vitro, animal, and human experiments have shown that boron is a bioactive element in nutritional amounts that beneficially affects bone growth and central nervous system function, alleviates arthritic symptoms, facilitates hormone action and is associated with a reduced risk for some types of cancer. The diverse effects of boron suggest that it influences the formation and/or activity of substances that are involved in numerous biochemical processes. Several findings suggest that this influence is through the formation of boroesters in biomolecules containing cis-hydroxyl groups. These biomolecules include those that contain ribose (e.g., S-adenosylmethionine, diadenosine phosphates, and nicotinamide adenine dinucleotide). In addition, boron may form boroester complexes with phosphoinositides, glycoproteins, and glycolipids that affect cell membrane integrity and function. Both animal and human data indicate that an intake of less than 1.0mg/day inhibits the health benefits of boron. Dietary surveys indicate such an intake is not rare. Thus, increasing boron intake by consuming a diet rich in fruits, vegetables, nuts and pulses should be recognized as a reasonable dietary recommendation to enhance health and well-being.

  2. Axial residual stresses in boron fibers

    Science.gov (United States)

    Behrendt, D. R.

    1978-01-01

    A method of measuring axial residual stresses in boron fibers is presented. With this method, the axial residual stress distribution as a function of radius is determined from the fiber surface to the core including the average residual stress in the core. Such measurements on boron on tungsten (B/W) fibers show that the residual stresses for 102, 142, 203, and 366 micron diam fibers are similar, being compressive at the surface and changing monotonically to a region of tensile stress within the boron. At approximately 25% of the original radius, the stress reaches a maximum tensile stress of about 860 MN sq m and then decreases to a compressive stress near the tungsten boride core. Data are presented for 203-micron diam B/W fibers that show annealing above 900 C reduces the residual stresses. A comparison between 102-micron diam B/W and boron on carbon (B/C) show that the residual stresses are similar in the outer regions of the fibers, but that large differences near and in the core are observed. Fracture of boron fibers is discussed.

  3. First gaseous boronization during pulsed discharge cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Ko, J., E-mail: jinseok@nfri.re.kr [Department of Physics, University of Wisconsin, Madison, WI (United States); Den Hartog, D.J.; Goetz, J.A.; Weix, P.J.; Limbach, S.T. [Department of Physics, University of Wisconsin, Madison, WI (United States)

    2013-01-15

    The first successful gaseous boronization during a pulsed discharge is reported. Sublimation of o-carborane (C{sub 2}B{sub 10}H{sub 12}) combined with pulsed discharge plasmas with a repetition rate of 1 Hz is used to produce a hard boron-containing coating for reversed field pinch (RFP) plasmas in the Madison Symmetric Torus. X-ray photoelectron spectroscopy with Ar ion beam etching for silicon coupons installed at the plasma boundary shows about 60% boron concentration in the deposited layer. Both profilometer and scanning electron microscope analyses of the silicon coupons imply a strong toroidally non-uniform deposition depending on the location of the o-carborane injection. The layer thickness ranges from 50 to 300 nm. Ellipsometry calibrated with the profilometer results yields a refractive index of 2.2-2.3 for the films. The high refractive index implies that the coating is hard and has a well-ordered morphology. A reduction in wall recycling has consistently been observed after all boronization sessions. Comparison of the X-ray spectra in standard RFP plasmas before and after boronization indicates a slight decrease in the effective ionic charge.

  4. First gaseous boronization during pulsed discharge cleaning

    Science.gov (United States)

    Ko, J.; Den Hartog, D. J.; Goetz, J. A.; Weix, P. J.; Limbach, S. T.

    2013-01-01

    The first successful gaseous boronization during a pulsed discharge is reported. Sublimation of o-carborane (C2B10H12) combined with pulsed discharge plasmas with a repetition rate of 1 Hz is used to produce a hard boron-containing coating for reversed field pinch (RFP) plasmas in the Madison Symmetric Torus. X-ray photoelectron spectroscopy with Ar ion beam etching for silicon coupons installed at the plasma boundary shows about 60% boron concentration in the deposited layer. Both profilometer and scanning electron microscope analyses of the silicon coupons imply a strong toroidally non-uniform deposition depending on the location of the o-carborane injection. The layer thickness ranges from 50 to 300 nm. Ellipsometry calibrated with the profilometer results yields a refractive index of 2.2-2.3 for the films. The high refractive index implies that the coating is hard and has a well-ordered morphology. A reduction in wall recycling has consistently been observed after all boronization sessions. Comparison of the X-ray spectra in standard RFP plasmas before and after boronization indicates a slight decrease in the effective ionic charge.

  5. Boron-Loaded Silicone Rubber Scintillators

    CERN Document Server

    Bell, Z W; Maya, L; Sloop, F V J

    2003-01-01

    Silicone rubber received attention as an alternative to polyvinyltoluene in applications in which the scintillator is exposed to high doses because of the increased resistance of the rubber to the formation of blue-absorbing color centers. Work by Bowen, et al., and Harmon, et al., demonstrated their properties under gamma/x-ray irradiation, and Bell, et al. have shown their response to thermal neutrons. This last work, however, provided an example of a silicone in which both the boron and the scintillator were contained in the rubber as solutes, a formulation which led to the precipitation of solids and sublimation of the boron component. In the present work we describe a scintillator in which the boron is chemically bonded to the siloxane and so avoids the problem of precipitation and loss of boron to sublimation. Material containing up to 18% boron, by weight, was prepared, mounted on photomultipliers, and exposed to both neutron and gamma fluxes. Pulse height spectra showing the neutron and photon respons...

  6. Chemical profile of mango (Mangifera indica L.) using electrospray ionisation mass spectrometry (ESI-MS).

    Science.gov (United States)

    Oliveira, Bruno G; Costa, Helber B; Ventura, José A; Kondratyuk, Tamara P; Barroso, Maria E S; Correia, Radigya M; Pimentel, Elisângela F; Pinto, Fernanda E; Endringer, Denise C; Romão, Wanderson

    2016-08-01

    Mangifera indica L., mango fruit, is consumed as a dietary supplement with purported health benefits; it is widely used in the food industry. Herein, the chemical profile of the Ubá mango at four distinct maturation stages was evaluated during the process of growth and maturity using negative-ion mode electrospray ionisation Fourier transform ion cyclotron resonance mass spectrometry (ESI(-)FT-ICR MS) and physicochemical characterisation analysis (total titratable acidity (TA), total soluble solids (TSS), TSS/TA ratio, and total polyphenolic content). Primary (organic acids and sugars) and secondary metabolites (polyphenolic compounds) were mostly identified in the third maturation stage, thus indicating the best stage for harvesting and consuming the fruit. In addition, the potential cancer chemoprevention of the secondary metabolites (phenolic extracts obtained from mango samples) was evaluated using the induction of quinone reductase activity, concluding that fruit polyphenols have the potential for cancer chemoprevention. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Small-Field Dosimetry in A 6 MV Photon Beam Using Alanine and Liquid Ionisation Chamber

    DEFF Research Database (Denmark)

    Zimmermann, S.; Riis, H. L.; Hjelm-Hansen, M.

    2012-01-01

    Lion ionisation chamber for small-field dosimetry in liquid water. Materials and Methods: The measurements were carried out on a Siemens Primus 58 leaves MLC. The alanine dosimeters were cylindric Ø4.9 mm × 3.0 mm and density of 1.2 g/cm3. The alanine dosimeters were placed on the top of a solid water stick of Ø4......, 2 times 4 sweeps with a 90° turn in between, total measurement time was 3 minutes per dosimeter. The alanine dosimetry system was calibrated using a Co60 gamma cell ensuring traceability to a national standard. Results: The results are summarized in Table 1. At depths below 2 mm, we noted...

  8. Electrifying atmospheres charging, ionisation and lightning in the solar system and beyond

    CERN Document Server

    Aplin, Karen L

    2013-01-01

    Electrical processes take place in all planetary atmospheres. There is evidence for lightning on Venus, Jupiter, Saturn, Uranus and Neptune, it is possible on Mars and Titan, and cosmic rays ionise every atmosphere, leading to charged droplets and particles. Controversy surrounds the role of atmospheric electricity in physical climate processes on Earth; here, a comparative approach is employed to review the role of electrification in the atmospheres of other planets and their moons. This book reviews the theory, and, where available, measurements, of planetary atmospheric electricity, taken to include ion production and ion-aerosol interactions. The conditions necessary for a global atmospheric electric circuit similar to Earth’s, and the likelihood of meeting these conditions in other planetary atmospheres, are briefly discussed. Atmospheric electrification is more important at planets receiving little solar radiation, increasing the relative significance of electrical forces. Nucleation onto atmospheric ...

  9. Molecular alterations in thyroid tumors induced after exposure to ionising radiation in infancy

    Energy Technology Data Exchange (ETDEWEB)

    Bounacer, A.; Wicker, R.; Sarasin, A.; Suarez, H.G. [Institut Gustave Roussy, 94 - Villejuif (France); Schlumberger, M.; Caillou, B. [Institut de Recherches sur le Cancer, 94 - Villejuif (France)

    1997-03-01

    We investigated the presence of molecular lesions in the ras, gsp and ret genes, in epithelial thyroid tumors developed in patients who had received ionising radiation therapy in infancy for benign or malignant conditions. Our data showed: a similar frequency of ras and gsp activating mutations in radiation-associated and `spontaneous` tumors. However, while the mutations are only transversions in the radiation-associated tumors, they are transversions as well as transitions in the `spontaneous` ones and a mutation in codon 691 giving rise to a polymorphism in the ret gene, and frequently associated to a C-cell hyperplasia in radiation-associated tumors. The frequency of this mutation was significantly higher (60%) in these tumors, than in normal controls (21%) or `spontaneous` epithelial thyroid tumors (23%). (author)

  10. Determination of potato glycoalkaloids using high-pressure liquid chromatography-electrospray ionisation/mass spectrometry.

    Science.gov (United States)

    Matsuda, Fumio; Morino, Keiko; Miyazawa, Haruna; Miyashita, Masahiro; Miyagawa, Hisashi

    2004-01-01

    A method for quantifying two toxic glycoalkaloids, alpha-solanine and alpha-chaconine, in potato (Solanum tuberosum) tuber tissue was developed using HPLC-electrospray ionisation (ESI)/MS. Potato samples were extracted with 5% aqueous acetic acid, and the extracts were subjected directly to HPLC-ESI/MS after filtration. By determining the intensities of the protonated molecules of alpha-solanine (m/z 868) and alpha-chaconine (m/z 852) using selected ion monitoring (positive ion mode), a sensitive assay was attained with detection limits of 38 and 14 ppb for the two glycoalkaloids, respectively. The high sensitivity and selectivity of MS detection effectively reduced the time of analysis thus enabling a high throughput assay of glycoalkaloids in potato tubers.

  11. Beer fingerprinting by Matrix-Assisted Laser Desorption-Ionisation-Time of Flight Mass Spectrometry.

    Science.gov (United States)

    Šedo, Ondrej; Márová, Ivana; Zdráhal, Zbyněk

    2012-11-15

    A method allowing parallel fingerprinting of proteins and maltooligosaccharides directly from untreated beer samples is presented. These two classes of compounds were detected by Matrix-Assisted Laser Desorption-Ionisation-Time of Flight-Mass Spectrometry (MALDI-TOF-MS) analysis of beer mixed with 2,5-dihydroxybenzoic acid solution. The maltooligosaccharide profiles acquired from the MALDI sample spot center were not found characteristic for beers of different source and technology. On the other hand, according to profiles containing protein signals acquired from crystals formed on the border of the MALDI sample spot, we were able to distinguish beer samples of the same brand produced by different breweries. The discriminatory abilities of the method were further examined on a set of 17 lager beers, where the fingerprints containing protein signals enabled resolution of majority of examined brands. We propose MALDI-TOF-MS profiling as a rapid tool for beer brewing technology process monitoring, quality control, and determination of beer authenticity.

  12. Ionisation in atmospheres of Brown Dwarfs and extrasolar planets I The role of electron avalanche

    CERN Document Server

    Helling, Ch; Witte, S; Diver, D A

    2010-01-01

    Brown Dwarf and extrasolar planet atmospheres form clouds which strongly influence the local chemistry and physics. These clouds are globally neutral obeying dust-gas charge equilibrium which is, on short time scales, inconsistent with the observation of stochastic ionisation events of the solar system planets. We argue that a significant volume of the clouds in Brown Dwarfs and extrasolar planets is susceptible to local discharge events. These are electron avalanches triggered by charged dust grains. Such intra-cloud discharges occur on time scales shorter than the time needed to neutralise the dust grains by collisional processes. An ensemble of discharges is likely to produce enough free charges to suggest a partial and stochastic coupling of the atmosphere to a large-scale magnetic field.

  13. Biological effects induced by K photo-ionisation in and near constituent atoms of DNA

    Energy Technology Data Exchange (ETDEWEB)

    Touati, A.; Herve du Penhoot, M.A.; Fayard, B.; Champion, C.; Abel, F.; Gobert, F.; Lamoureux, M.; Politis, M.F.; Martins, L.; Ricoul, M.; Sabatier, L.; Sage, E.; Chetioui, A

    2002-07-01

    In order to assess the lethal efficiency and other biological effects of inner shell ionisations of constituent atoms of DNA ('K' events), experiments were developed at the LURE synchrotron facility using ultrasoft X rays as a probe of K events. The lethal efficiency of ultrasoft X rays above the carbon K threshold was especially investigated using V79 cells and compared with their efficiency to induce double strand breaks in dry plasmid-DNA. A correlation between the K event efficiencies for these processes is shown. Beams of 340 eV were found to be twice as efficient at killing cells than were beams at 250 eV. In addition, a rough two-fold increase of the relative biological effectiveness for dicentric+ring induction has also been observed between 250 and 340 eV radiations. (author)

  14. Non-ionising radiation human exposure assessment near telecommunication devices in Croatia.

    Science.gov (United States)

    Simunić, Dina

    2006-03-01

    This paper gives an overview of the regulatory acts in non-ionising radiation in the world, with a special emphasis on basic guidelines issued by the International Commission on Non-Ionizing Radiation Protection (ICNIRP). ICNIRP Guidelines are implemented in many countries worldwide. Croatia has also implemented them indirectly through the European Recommendation 1999/519/EC. The Croatian regulatory acts include the Non-lonising Radiation Protection Act, Ordinance on Electromagnetic Fields (EMF) Protection, and the Ordinance on Basic Requirements for Devices which produce Optical Radiation and Measures for Optical Radiation Protection. Dosimetry and densitometry are compliant with relevant international and European standards. The paper presents an example of densitometric human exposure assessment in complex indoor exposure conditions. In spite of a high number of indoor and outdoor sources and the "worst-case exposure assessment", the results are within the limits defined by the Croatian EMF Ordinance.

  15. Dietary boron: possible roles in human and animal physiology

    Science.gov (United States)

    Boron is a bioactive element of low molecular weight. Since discovery of the first boron biomolecule, boromycin, in 1967, several other similar biomolecules are now well-characterized. Most recently described was a bacterial cell-to-cell communication signal that requires boron, autoinducer-II. Boro...

  16. Mechanical and physical properties of modern boron fibers

    Science.gov (United States)

    Dicarlo, J. A.

    1978-01-01

    Measurements of the Young's modulus, flexural modulus, shear modulus and Poisson's ratio for boron fibers prepared by modern deposition techniques are reported. Physical properties of the boron fibers, including density, thermal expansion and resistance, are also surveyed. In addition, prediction of the total deformation strain in an anelastic boron fiber subjected to tensile or flexural stress is discussed.

  17. Boronic acid functionalized polymers and hydrogels for biomedical applications

    NARCIS (Netherlands)

    Piest, Martin

    2011-01-01

    Boronic acid functionalized polymers are a very interesting class of materials capable of forming reversible covalent boronic esters. With boronic acids reversible binding of diols and polyols, including carbohydrates, is possible. Although such polymers are promising biomaterials, they are only rar

  18. Colorimetric Sugar Sensing Using Boronic Acid-Substituted Azobenzenes

    Science.gov (United States)

    Egawa, Yuya; Miki, Ryotaro; Seki, Toshinobu

    2014-01-01

    In association with increasing diabetes prevalence, it is desirable to develop new glucose sensing systems with low cost, ease of use, high stability and good portability. Boronic acid is one of the potential candidates for a future alternative to enzyme-based glucose sensors. Boronic acid derivatives have been widely used for the sugar recognition motif, because boronic acids bind adjacent diols to form cyclic boronate esters. In order to develop colorimetric sugar sensors, boronic acid-conjugated azobenzenes have been synthesized. There are several types of boronic acid azobenzenes, and their characteristics tend to rely on the substitute position of the boronic acid moiety. For example, o-substitution of boronic acid to the azo group gives the advantage of a significant color change upon sugar addition. Nitrogen-15 Nuclear Magnetic Resonance (NMR) studies clearly show a signaling mechanism based on the formation and cleavage of the B–N dative bond between boronic acid and azo moieties in the dye. Some boronic acid-substituted azobenzenes were attached to a polymer or utilized for supramolecular chemistry to produce glucose-selective binding, in which two boronic acid moieties cooperatively bind one glucose molecule. In addition, boronic acid-substituted azobenzenes have been applied not only for glucose monitoring, but also for the sensing of glycated hemoglobin and dopamine. PMID:28788510

  19. Colorimetric Sugar Sensing Using Boronic Acid-Substituted Azobenzenes

    Directory of Open Access Journals (Sweden)

    Yuya Egawa

    2014-02-01

    Full Text Available In association with increasing diabetes prevalence, it is desirable to develop new glucose sensing systems with low cost, ease of use, high stability and good portability. Boronic acid is one of the potential candidates for a future alternative to enzyme-based glucose sensors. Boronic acid derivatives have been widely used for the sugar recognition motif, because boronic acids bind adjacent diols to form cyclic boronate esters. In order to develop colorimetric sugar sensors, boronic acid-conjugated azobenzenes have been synthesized. There are several types of boronic acid azobenzenes, and their characteristics tend to rely on the substitute position of the boronic acid moiety. For example, o-substitution of boronic acid to the azo group gives the advantage of a significant color change upon sugar addition. Nitrogen-15 Nuclear Magnetic Resonance (NMR studies clearly show a signaling mechanism based on the formation and cleavage of the B–N dative bond between boronic acid and azo moieties in the dye. Some boronic acid-substituted azobenzenes were attached to a polymer or utilized for supramolecular chemistry to produce glucose-selective binding, in which two boronic acid moieties cooperatively bind one glucose molecule. In addition, boronic acid-substituted azobenzenes have been applied not only for glucose monitoring, but also for the sensing of glycated hemoglobin and dopamine.

  20. CF3(+) and CF2H(+): new reagents for n-alkane determination in chemical ionisation reaction mass spectrometry.

    Science.gov (United States)

    Blake, Robert S; Ouheda, Saleh A; Evans, Corey J; Monks, Paul S

    2016-11-28

    Alkanes provide a particular analytical challenge to commonly used chemical ionisation methods such as proton-transfer from water owing to their basicity. It is demonstrated that the fluorocarbon ions CF3(+) and CF2H(+), generated from CF4, as reagents provide an effective means of detecting light n-alkanes in the range C2-C6 using direct chemical ionisation mass spectrometry. The present work assesses the applicability of the reagents in Chemical Ionisation Mass Spectrometric (CI-TOF-MS) environments with factors such as high moisture content, operating pressures of 1-10 Torr, accelerating electric fields (E/N) and long-lived intermediate complex formation. Of the commonly used chemical ionisation reagents, H3O(+) and NO(+) only react with hexane and higher while O2(+) reacts with all the target samples, but creates significant fragmentation. By contrast, CF3(+) and CF2H(+) acting together were found to produce little or no fragmentation. In dry conditions with E/N = 100 Td or higher the relative intensity of CF2H(+) to CF3(+) was mostly less than 1% but always less than 3%, making CF3(+) the main reagent ion. Using O2(+) in a parallel series of experiments, a substantially greater degree of fragmentation was observed. The detection sensitivities of the alkanes with CF3(+) and CF2H(+), while relatively low, were found to be better than those observed with O2(+). Experiments using alkane mixtures in the ppm range have shown the ionisation technique based on CF3(+) and CF2H(+) to be particularly useful for measurements of alkane/air mixtures found in polluted environments. As a demonstration of the technique's effectiveness in complex mixtures, the detection of n-alkanes in a smoker's breath is demonstrated.

  1. Application of Lithium Attachment Mass Spectrometry for Knudsen Evaporation and Chemical Ionisation Mass Spectrometry (KEMS, CIMS)

    Science.gov (United States)

    Bannan, Thomas; Booth, A. Murray; Alfarra, Rami; Bacak, Asan; Pericval, Carl

    2016-04-01

    Lithium ion attachment mass spectrometry provides a non-specific, non-fragmenting and sensitive method for detection of volatile species in the gas phase. The design, manufacture, and results from lithium ion attachment ionisation sources for two mass spectrometry systems are presented. Trace gas analysis is investigated using a modified Chemical Ionization Mass Spectrometer (CIMS) and vapour pressure (VP) measurements using a modified Knudsen Effusion Mass Spectrometer (KEMS) are presented. The Li+ modified CIMS provided limits of detection of 4 ppt for acetone, 0.2 ppt for formic acid, 15 ppt for nitric acid and 120 ppt from ammonia. Despite improvements, the problem of burnout remained persistent. The Li+ CIMS would unlikely be suitable for field or aircraft work, but could be appropriate for certain lab applications. The KEMS currently utilizes an electron impact (EI) ionisation source which provides a highly sensitive source, with the drawback of fragmentation of ionized molecules (Booth et al., 2009). Using Li+ KEMS the VP of samples can be measured without fragmentation and can therefore be used to identify VPs of individual components in mixtures. The validity of using Li+ for determining the VP of mixtures was tested by making single component VP measurements, which showed good agreement with EI measurements of Poly ethylene glycol (PEG) 3 and PEG 4, both when individually measured and when mixed. The Li+ KEMS was then used to investigate a system of atmospheric relevance, α-pinene secondary organic aerosol, generated in a reaction chamber (Alfarra et al., 2012). The VPs of the individual components from this generated sample are within the range we expect for compounds capable of partitioning between the particle and gas phase of an aerosol (0.1-10-5 Pa). Li+ source has a calculated sensitivity approximately 75 times less than that of EI, but the lack of fragmentation using the Li+ source is a significant advantage.

  2. The ionising radiations: a daily reality Las radiaciones ionizantes: una realidad cotidiana

    Directory of Open Access Journals (Sweden)

    Eduardo Gallego Díaz

    2010-12-01

    Full Text Available This paper introduce the nature of the radioactive substances and of the ionising radiation, the effects that they cause on the matter and the available media for their detection and measure, as well as the sources of natural radiation, to which the human being are exposed. Next, in the more detailed part of this paper, it is described the wide range of ionising radiations uses in: medicine, agriculture, earth sciences, biology and in some other scientific fields, that allow to pose its impact in the perspective of facing the ones from natural sources. The article concludes that for avoiding damages it is necessary proper protection against the radioactive substances, but avoiding limitation their beneficial uses in the various ranges described. For finishing this paper, the basic principles of radiation protection are described, due to they are the its principal aim.Este trabajo introduce la naturaleza de las sustancias radiactivas y de la radiación ionizante, los efectos que causa sobre la materia y los medios disponibles para su detección y medida, así como las fuentes de radiación naturales a las que los seres humanos estamos expuestos. Seguidamente, en el apartado más amplio del trabajo, se describen las múltiples aplicaciones de las radiaciones ionizantes en la medicina, la agricultura, la industria, las ciencias de la tierra, la biología y otras ramas, lo que permite poder poner su impacto en perspectiva frente al de las fuentes naturales. La tesis final del artículo es que para evitar sufrir daños resulta necesario protegerse adecuadamente de los efectos nocivos de la radiación y las sustancias radiactivas, pero sin limitar innecesariamente su utilización beneficiosa en los numerosos ámbitos descritos. Ese es el objetivo fundamental de la protección radiológica, cuyos principios básicos se presentan para terminar.

  3. Mapping boron in silicon solar cells using electron energy-loss spectroscopy

    DEFF Research Database (Denmark)

    -doped layers. The typical boron concentration in the p-doped layer is ~10^21cm -3 and should not exceed 1017cm-3 in the neighbouring intrinsic (i) layer [1], where it acts as a charge recombination centre and decreases the internal electric field [2]. The detection of low boron concentrations with high spatial...... resolution using TEM is highly challenging [3]. Recently, scanning TEM (STEM) combined with electron energy-loss spectroscopy (EELS) and spherical aberration-correction has allowed the direct detection of dopant concentration of 10^20cm-3 in 65-nm-wide silicon devices [4]. Here, we prepare TEM samples...... by focused ion beam milling in order to map the boron distribution across a 200-nm-thick n-p amorphous silicon junction using energy-filtered TEM and EELS spectrum acquisition. EELS line scans are used to detect boron concentrations as low as 10^20cm-3. We also use monochromated EELS to measure changes...

  4. The study of some thiazinic and indaminic dye syntheses induced by ionising radiation; Etude de quelques syntheses de colorants thianziniques et indaminiques amorcees par les rayonnements ionisants

    Energy Technology Data Exchange (ETDEWEB)

    Balestic, S. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-03-15

    With a view to finding some radiochemical reactions applicable on an industrial scale for evaluating the radioactive waste from nuclear reactors, a systematic study was made of the radiochemical synthesis of thiazinic dyes such as methylene blue and Lauths' violet, on which the first tests were carried out in 1954. The first part of the study concerned the identification and the dosage, during radiolysis, of dyes by means of their absorption spectra after separation from the reaction medium by adsorption chromatography or ion-exchange; other radiolysis products such as ammonium chloride and hydrogen peroxide were also identified. During a later stage by systematically varying the physico-chemical parameters it was possible to determine the most favourable conditions for radio-synthesis; the maximum radiochemical yields obtained had the following values: G (Lauths' violet) 1,65; G (Methylene blue) = 1,75. Furthermore, the study of the influence of variously substituted aminated products on the radiochemical yield showed the possibility of synthesising Bindsehedlers green and Wursters blue by radiochemical methods. Finally the discovery of a fundamental intermediate product, Wursters red, together with the kinetic study of the chemical synthesis of methylene blue made it possible to determine the main stages of the reaction mechanism and to decide which of these stages could be attributed to ionising radiations in the case of the radiochemical synthesis. (author) [French] Dans le but de trouver des reactions radiochimiques susceptibles d'une application industrielle pour valoriser les dechets radioactifs provenant des reacteurs nucleaires, il a ete entrepris une etude systematique de la synthese radiochimique des colorants thiazimiques tels que le Bleu de Methylene et le Violet de Lauth dont les premiers essais ont ete effectues par Loiseleur en 1954. La premiere partie de l'etude a porte sur l'identification et le dosage des colorants formes

  5. Simultaneous determination of volatile and non-volatile nitrosamines in processed meat products by liquid chromatography tandem mass spectrometry using atmospheric pressure chemical ionisation and electrospray ionisation.

    Science.gov (United States)

    Herrmann, S S; Duedahl-Olesen, L; Granby, K

    2014-02-21

    A sensitive, selective and generic method has been developed for the simultaneous determination of the contents (μgkg(-1) range) of both volatile nitrosamines (VNA) and non-volatile nitrosamines (NVNA) in processed meat products. The extraction procedure only requires basic laboratory equipment and a small volume of organic solvent. Separation and quantification were performed by the developed LC-(APCI/ESI)MS/MS method. The method was validated using spiked samples of three different processed meat products. Satisfactory recoveries (50-130%) and precisions (2-23%) were obtained for eight VNA and six NVNAs with LODs generally between 0.2 and 1μgkg(-1), though for a few analyte/matrix combinations higher LODs were obtained (3 to 18μgkg(-1)). The validation results show that results obtained for one meat product is not always valid for other meat products. We were not able to obtain satisfactory results for N-nitrosohydroxyproline (NHPRO), N-nitrosodibenzylamine (NDBzA) and N-nitrosodiphenylamine (NDPhA). Application of the APCI interface improved the sensitivity of the method, because of less matrix interference, and gave the method a wider scope, as some NAs were ionisable only by APCI. However, it was only possible to ionize N-nitroso-thiazolidine-4-carboxylic acid (NTCA) and N-nitroso-2-methyl-thiazolidine-4-carboxylic acid (NMTCA) by ESI. The validated method was applied for the analysis of processed meat products and contents of N-nitrosodimethylamine (NDMA), N-nitrosopyrrolidine (NPYR), N-nitrosomethylaniline (NMA), N-nitrosoproline (NPRO), NTCA, and NMTCA were found in one or several nitrite cured meat products, whereas none were detected in non-nitrite cured bacon.

  6. Conducting Boron Sheets Formed by the Reconstruction of the α-Boron (111) Surface

    Science.gov (United States)

    Amsler, Maximilian; Botti, Silvana; Marques, Miguel A. L.; Goedecker, Stefan

    2013-09-01

    Systematic ab initio structure prediction was applied for the first time to predict low energy surface reconstructions by employing the minima hopping method on the α-boron (111) surface. Novel reconstruction geometries were identified and carefully characterized in terms of structural and electronic properties. Our calculations predict the formation of a planar, monolayer sheet at the surface, which is responsible for conductive surface states. Furthermore, the isolated boron sheet is shown to be the ground state 2D structure in vacuum at a hole density of η=1/5 and is therefore a potential candidate as a precursor for boron nanostructures.

  7. Lateral gas phase diffusion length of boron atoms over Si/B surfaces during CVD of pure boron layers

    NARCIS (Netherlands)

    Mohammadi, V.; Nihtianov, S.

    2016-01-01

    The lateral gas phase diffusion length of boron atoms, LB, along silicon and boron surfaces during chemical vapor deposition(CVD) using diborane (B2H6) is reported. The value of LB is critical for reliable and uniform boron layer coverage. The presented information was obtained experimentally and co

  8. Lateral gas phase diffusion length of boron atoms over Si/B surfaces during CVD of pure boron layers

    NARCIS (Netherlands)

    Mohammadi, V.; Nihtianov, S.

    2016-01-01

    The lateral gas phase diffusion length of boron atoms, LB, along silicon and boron surfaces during chemical vapor deposition(CVD) using diborane (B2H6) is reported. The value of LB is critical for reliable and uniform boron layer coverage. The presented information was obtained experimentally and co

  9. Oxygen radical functionalization of boron nitride nanosheets.

    Science.gov (United States)

    Sainsbury, Toby; Satti, Amro; May, Peter; Wang, Zhiming; McGovern, Ignatius; Gun'ko, Yurii K; Coleman, Jonathan

    2012-11-14

    The covalent chemical functionalization of exfoliated hexagonal boron-nitride nanosheets (BNNSs) is achieved by the solution-phase oxygen radical functionalization of boron atoms in the h-BN lattice. This involves a two-step procedure to initially covalently graft alkoxy groups to boron atoms and the subsequent hydrolytic defunctionalization of the groups to yield hydroxyl-functionalized BNNSs (OH-BNNSs). Characterization of the functionalized-BNNSs using HR-TEM, Raman, UV-vis, FTIR, NMR, and TGA was performed to investigate both the structure of the BNNSs and the covalent functionalization methodology. OH-BNNSs were used to prepare polymer nanocomposites and their mechanical properties analyzed. The influence of the functional groups grafted to the surface of the BNNSs is investigated by demonstrating the impact on mechanical properties of both noncovalent and covalent bonding at the interface between the nanofiller and polymer matrixes.

  10. Probing Field Emission from Boron Carbide Nanowires

    Institute of Scientific and Technical Information of China (English)

    TIAN Ji-Fa; GAO Hong-Jun; BAO Li-Hong; WANG Xing-Jun; HUI Chao; LIU Fei; LI Chen; SHEN Cheng-Min; WANG Zong-Li; GU Chang-Zhi

    2008-01-01

    High density boron carbide nanowires are grown by an improved carbon thermal reduction technique. Transmission electron microscopy and electron energy lose spectroscopy of the sample show that the synthesized nanowires are B4 C with good crystallization. The field emission measurement for an individual boron nanowire is performed by using a Pt tip installed in the focused ion beam system. A field emission current with enhancement factor of 106 is observed and the evolution process during emission is also carefully studied. Furthermore, a two-step field emission with stable emission current density is found from the high-density nanowire film. Our results together suggest that boron carbide nanowires are promising candidates for electron emission nanodevices.

  11. Metallicity of boron carbides at high pressure

    Science.gov (United States)

    Dekura, Haruhiko; Shirai, Koun; Yanase, Akira

    2010-03-01

    Electronic structure of semiconducting boron carbide at high pressure has been theoretically investigated, because of interests in the positive pressure dependence of resistivity, in the gap closure, and in the phase transition. The most simplest form B12(CCC) is assumed. Under assumptions of hydrostatic pressure and neglecting finite-temperature effects, boron carbide is quite stable at high pressure. The crystal of boron carbide is stable at least until a pressure higher than previous experiments showed. The gap closure occurs only after p=600 GPa on the assumption of the original crystal symmetry. In the low pressure regime, the pressure dependence of the energy gap almost diminishes, which is an exceptional case for semiconductors, which could be one of reasons for the positive pressure dependence of resistivity. A monotonous increase in the apex angle of rhombohedron suggests that the covalent bond continues to increase. The C chain inserted in the main diagonal of rhombohedral structure is the chief reason of this stability.

  12. Depth resolved investigations of boron implanted silicon

    Energy Technology Data Exchange (ETDEWEB)

    Sztucki, M. E-mail: michael@sztucki.de; Metzger, T.H.; Milita, S.; Berberich, F.; Schell, N.; Rouviere, J.L.; Patel, J

    2003-01-01

    We have studied the depth distribution and structure of defects in boron implanted silicon (0 0 1). Silicon wafers were implanted with a boron dose of 6x10{sup 15} ions/cm{sup -2} at 32 keV and went through different annealing treatments. Using diffuse X-ray scattering at grazing incidence and exit angles we are able to distinguish between different kinds of defects (point defect clusters and extrinsic stacking faults on {l_brace}1 1 1{r_brace} planes) and to determine their depth distribution as a function of the thermal budget. Cross-section transmission electron microscopy was used to gain complementary information. In addition we have determined the strain distribution caused by the boron implantation as a function of depth from rocking curve measurements.

  13. Boron removal by electrocoagulation and recovery.

    Science.gov (United States)

    Isa, Mohamed Hasnain; Ezechi, Ezerie Henry; Ahmed, Zubair; Magram, Saleh Faraj; Kutty, Shamsul Rahman Mohamed

    2014-03-15

    This work investigated the removal of boron from wastewater and its recovery by electrocoagulation and hydrothermal mineralization methods respectively. The experimental design was developed using Box-Behnken Model. An initial study was performed based on four preselected variables (pH, current density, concentration and time) using synthetic wastewater. Response surface methodology (RSM) was used to evaluate the effect of process variables and their interaction on boron removal. The optimum conditions were obtained as pH 6.3, current density 17.4 mA/cm(2), and time 89 min. At these applied optimum conditions, 99.7% boron removal from an initial concentration of 10.4 mg/L was achieved. The process was effectively optimized by RSM with a desirability value of 1.0. The results showed that boron removal efficiency enhanced with increase in current density and treatment time. Removal efficiency also increased when pH was increased from 4 to 7 and subsequently decreased at pH 10. Adsorption kinetics study revealed that the reaction followed pseudo second order kinetic model; evidenced by high correlation and goodness of fit. Thermodynamics study showed that mechanism of boron adsorption was chemisorption and the reaction was endothermic in nature. Furthermore, the adsorption process was spontaneous as indicated by negative values of the adsorption free energy. Treatment of real produced water using electrocoagulation resulted in 98% boron removal. The hydrothermal mineralization study showed that borate minerals (Inyoite, Takadaite and Nifontovite) can be recovered as recyclable precipitate from electrocoagulation flocs of produced water.

  14. Dietary boron: progress in establishing essential roles in human physiology.

    Science.gov (United States)

    Hunt, Curtiss D

    2012-06-01

    This review summarizes the progress made in establishing essential roles for boron in human physiology and assesses that progress in view of criteria for essentiality of elements. The evidence to date suggests that humans and at least some higher animals may use boron to support normal biological functions. These include roles in calcium metabolism, bone growth and maintenance, insulin metabolism, and completion of the life cycle. The biochemical mechanisms responsible for these effects are poorly understood but the nature of boron biochemistry suggests further characterization of the cell signaling molecules capable of complexing with boron. Such characterization may provide insights into the biochemical function(s) of boron in humans.

  15. Low pressure growth of cubic boron nitride films

    Science.gov (United States)

    Ong, Tiong P. (Inventor); Shing, Yuh-Han (Inventor)

    1997-01-01

    A method for forming thin films of cubic boron nitride on substrates at low pressures and temperatures. A substrate is first coated with polycrystalline diamond to provide a uniform surface upon which cubic boron nitride can be deposited by chemical vapor deposition. The cubic boron nitride film is useful as a substitute for diamond coatings for a variety of applications in which diamond is not suitable. any tetragonal or hexagonal boron nitride. The cubic boron nitride produced in accordance with the preceding example is particularly well-suited for use as a coating for ultra hard tool bits and abrasives, especially those intended to use in cutting or otherwise fabricating iron.

  16. Nuclear quadrupole resonance of boron in borate glasses

    Science.gov (United States)

    Gravina, Samuel J.; Bray, Phillip J.

    A continuous wave nuclear quadrupole resonance spectrometer that has a high sensitivity even at low frequencies has been built. Boron and aluminum NQR has been detected in the region 200 kHz to 1.4 MHz. For the first time, boron NQR has been detected in a glass. The NQR spectrum of pure B 20 3 glass is consistent with 85 ± 2% of the boron atoms belonging to boroxol rings. In sodium borate glasses, the number of borons in boroxol rings decreases with increasing sodium content, until when sodium oxide comprises 20 mol% of the glass less than 2% of the borons are in boroxol rings.

  17. Urea-containing peptide boronic acids as potent proteasome inhibitors.

    Science.gov (United States)

    Han, Li-Qiang; Yuan, Xia; Wu, Xing-Yu; Li, Ri-Dong; Xu, Bo; Cheng, Qing; Liu, Zhen-Ming; Zhou, Tian-Yan; An, Hao-Yun; Wang, Xin; Cheng, Tie-Ming; Ge, Ze-Mei; Cui, Jing-Rong; Li, Run-Tao

    2017-01-05

    A novel class of urea-containing peptide boronic acids as proteasome inhibitors was designed by introducing a urea scaffold to replace an amido bond. Compounds were synthesized and their antitumor activities were evaluated. After two rounds of optimizations, the compound I-14 was found to be a potent proteasome inhibitor. Compared with Bortezomib, I-14 showed higher potency against the chymotrypsin-like activity of human 20S proteasome (IC50 < 1 pM), similar potency against four different cancer cell lines (IC50 < 10 nM), and better pharmacokinetic profile. Furthermore, I-14 significantly inhibited tumor growth in Bel7404 mouse xenograft model. The excellent proteasome inhibition by I-14 was rationalized through docking and molecular dynamics studies. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  18. Line, LINER, linest - from micro-AGN to ultra-luminous LINERs. One and the same?

    CERN Document Server

    Winkler, Hartmut

    2014-01-01

    This paper compares the optical spectra of a wide range of galaxies categorised as members of the Low Ionisation Nuclear Emission Region (LINER) class of active galactic nuclei (AGN). LINERs are defined by emission spectra with relatively faint high ionisation lines (compared to other AGN classes). The gas emission luminosity ranges from the weak flux emanating from some nearby galactic nuclei all the way to extremely luminous radio galaxies, where the line emission can completely dominate the host galaxy starlight component. In this study I analyse the Sloane Digital Sky Survey optical spectra of 15 LINERS identified in the course of the preparation of the new edition of the ZORROASTER AGN catalogue, spanning the largest possible luminosity range. I compare relative emission line strengths, focusing on uncommonly analysed ratios such as those involving [N I], line widths, profiles and even the spectral features of the host galaxy stellar continuum. The study identifies possible luminosity dependent trends in...

  19. Fragmentation d'agrégats de carbone (multi) chargés formés par ionisation et excitation en collision de haute vitesse

    OpenAIRE

    2005-01-01

    M L. ADOUI, Rapporteur Mme L. CHEN, Rapporteur M P.A. HERVIEUX Mme C. JOBLIN Mme L. TCHANG-BRILLET, Présidente du jury; The present work is devoted to the study of the excitation, ionisation and fragmentation of monocharged carbon clusters C^+_n (n \\leq 10) induced by high velocity (2.6au) collision on helium gas. For this velocity regime the electronic mechanisms of excitation and ionisation are dominant. The collision processes (electronic excitation, simple and (multi) ionisation, fragment...

  20. The use of particle beam mass spectrometry for the measurement of impurities in a nabumetone drug substance, not easily amenable to atmospheric pressure ionisation techniques.

    Science.gov (United States)

    Wolff, J C; Hawtin, P N; Monté, S; Balogh, M; Jones, T

    2001-01-01

    Liquid chromatography/particle beam mass spectrometry (LC/PB-MS) was used for the structural elucidation of some impurities in nabumetone as this compound poorly ionises by atmospheric pressure ionisation (API) techniques. PB-MS was optimised for nabumetone and a sensitivity study was carried out. To obtain full scan electron ionisation spectra a minimum of 100 ng of compound on column was needed. By using 20 mg/mL solutions of nabumetone, impurities at levels of about 250 ppm mass fraction relative to nabumetone could be detected. Results were compared with LC/API-MS and previous GC/MS.

  1. Boron Nitride Nanotubes for Spintronics

    Directory of Open Access Journals (Sweden)

    Kamal B. Dhungana

    2014-09-01

    Full Text Available With the end of Moore’s law in sight, researchers are in search of an alternative approach to manipulate information. Spintronics or spin-based electronics, which uses the spin state of electrons to store, process and communicate information, offers exciting opportunities to sustain the current growth in the information industry. For example, the discovery of the giant magneto resistance (GMR effect, which provides the foundation behind modern high density data storage devices, is an important success story of spintronics; GMR-based sensors have wide applications, ranging from automotive industry to biology. In recent years, with the tremendous progress in nanotechnology, spintronics has crossed the boundary of conventional, all metallic, solid state multi-layered structures to reach a new frontier, where nanostructures provide a pathway for the spin-carriers. Different materials such as organic and inorganic nanostructures are explored for possible applications in spintronics. In this short review, we focus on the boron nitride nanotube (BNNT, which has recently been explored for possible applications in spintronics. Unlike many organic materials, BNNTs offer higher thermal stability and higher resistance to oxidation. It has been reported that the metal-free fluorinated BNNT exhibits long range ferromagnetic spin ordering, which is stable at a temperature much higher than room temperature. Due to their large band gap, BNNTs are also explored as a tunnel magneto resistance device. In addition, the F-BNNT has recently been predicted as an ideal spin-filter. The purpose of this review is to highlight these recent progresses so that a concerted effort by both experimentalists and theorists can be carried out in the future to realize the true potential of BNNT-based spintronics.

  2. Boron nitride nanotubes for spintronics.

    Science.gov (United States)

    Dhungana, Kamal B; Pati, Ranjit

    2014-09-22

    With the end of Moore's law in sight, researchers are in search of an alternative approach to manipulate information. Spintronics or spin-based electronics, which uses the spin state of electrons to store, process and communicate information, offers exciting opportunities to sustain the current growth in the information industry. For example, the discovery of the giant magneto resistance (GMR) effect, which provides the foundation behind modern high density data storage devices, is an important success story of spintronics; GMR-based sensors have wide applications, ranging from automotive industry to biology. In recent years, with the tremendous progress in nanotechnology, spintronics has crossed the boundary of conventional, all metallic, solid state multi-layered structures to reach a new frontier, where nanostructures provide a pathway for the spin-carriers. Different materials such as organic and inorganic nanostructures are explored for possible applications in spintronics. In this short review, we focus on the boron nitride nanotube (BNNT), which has recently been explored for possible applications in spintronics. Unlike many organic materials, BNNTs offer higher thermal stability and higher resistance to oxidation. It has been reported that the metal-free fluorinated BNNT exhibits long range ferromagnetic spin ordering, which is stable at a temperature much higher than room temperature. Due to their large band gap, BNNTs are also explored as a tunnel magneto resistance device. In addition, the F-BNNT has recently been predicted as an ideal spin-filter. The purpose of this review is to highlight these recent progresses so that a concerted effort by both experimentalists and theorists can be carried out in the future to realize the true potential of BNNT-based spintronics.

  3. Ultrahard nanotwinned cubic boron nitride.

    Science.gov (United States)

    Tian, Yongjun; Xu, Bo; Yu, Dongli; Ma, Yanming; Wang, Yanbin; Jiang, Yingbing; Hu, Wentao; Tang, Chengchun; Gao, Yufei; Luo, Kun; Zhao, Zhisheng; Wang, Li-Min; Wen, Bin; He, Julong; Liu, Zhongyuan

    2013-01-17

    Cubic boron nitride (cBN) is a well known superhard material that has a wide range of industrial applications. Nanostructuring of cBN is an effective way to improve its hardness by virtue of the Hall-Petch effect--the tendency for hardness to increase with decreasing grain size. Polycrystalline cBN materials are often synthesized by using the martensitic transformation of a graphite-like BN precursor, in which high pressures and temperatures lead to puckering of the BN layers. Such approaches have led to synthetic polycrystalline cBN having grain sizes as small as ∼14 nm (refs 1, 2, 4, 5). Here we report the formation of cBN with a nanostructure dominated by fine twin domains of average thickness ∼3.8 nm. This nanotwinned cBN was synthesized from specially prepared BN precursor nanoparticles possessing onion-like nested structures with intrinsically puckered BN layers and numerous stacking faults. The resulting nanotwinned cBN bulk samples are optically transparent with a striking combination of physical properties: an extremely high Vickers hardness (exceeding 100 GPa, the optimal hardness of synthetic diamond), a high oxidization temperature (∼1,294 °C) and a large fracture toughness (>12 MPa m(1/2), well beyond the toughness of commercial cemented tungsten carbide, ∼10 MPa m(1/2)). We show that hardening of cBN is continuous with decreasing twin thickness down to the smallest sizes investigated, contrasting with the expected reverse Hall-Petch effect below a critical grain size or the twin thickness of ∼10-15 nm found in metals and alloys.

  4. Hollow boron nitride nanospheres as boron reservoir for prostate cancer treatment

    Science.gov (United States)

    Li, Xia; Wang, Xiupeng; Zhang, Jun; Hanagata, Nobutaka; Wang, Xuebin; Weng, Qunhong; Ito, Atsuo; Bando, Yoshio; Golberg, Dmitri

    2017-01-01

    High global incidence of prostate cancer has led to a focus on prevention and treatment strategies to reduce the impact of this disease in public health. Boron compounds are increasingly recognized as preventative and chemotherapeutic agents. However, systemic administration of soluble boron compounds is hampered by their short half-life and low effectiveness. Here we report on hollow boron nitride (BN) spheres with controlled crystallinity and boron release that decrease cell viability and increase prostate cancer cell apoptosis. In vivo experiments on subcutaneous tumour mouse models treated with BN spheres demonstrated significant suppression of tumour growth. An orthotopic tumour growth model was also utilized and further confirmed the in vivo anti-cancer efficacy of BN spheres. Moreover, the administration of hollow BN spheres with paclitaxel leads to synergetic effects in the suppression of tumour growth. The work demonstrates that hollow BN spheres may function as a new agent for prostate cancer treatment.

  5. Hierarchical supramolecules and organization using boronic acid building blocks.

    Science.gov (United States)

    Kubo, Yuji; Nishiyabu, Ryuhei; James, Tony D

    2015-02-07

    Current progress on hierarchical supramolecules using boronic acids has been highlighted in this feature article. Boronic acids can participate in "click reactions" with diols and their congeners with dynamic covalent functionality. By comprehensively exploring versatile sequential boronate esterification linkages between plural boronic acid-appended molecules and multiple hydroxyl counterparts, not only versatile supramolecular polymers but also structurally well-defined network nanostructures have been developed. In addition orthogonal interactions such as dative bonds of the boron center with Lewis bases have led to the formation of hierarchical nano/microstructures. Boronate systems have the potential to be used as materials for smart gels, chemosensors, active architectures for electronics, heterogeneous catalysts, chemical-stimulus responsive systems for drug delivery, etc. Here, we fully discuss the feasibility of the structure-directing ability of boronic acids from the standpoint of the generation of new smart materials.

  6. Efficient boron abstraction using honeycomb-like porous magnetic hybrids: Assessment of techno-economic recovery of boric acid.

    Science.gov (United States)

    Oladipo, Akeem Adeyemi; Gazi, Mustafa

    2016-12-01

    Porous magnetic hybrids were synthesized and functionalized with glycidol to produce boron-selective adsorbent. The magnetic hybrid (MH) comparatively out-performed the existing expensive adsorbents. MH had a saturation magnetisation of 63.48 emu/g and average pore diameter ranging from meso to macropores. The magnetic hybrids showed excellent selectivity towards boron and resulted in 79-93% boron removal even in the presence of competing metal ions (Na(+) and Cr(2+)). Experiments were performed in a column system, and breakthrough time was observed to increase with bed depths and decreased with flow rates. The batch experiments revealed that 60 min was enough to achieve equilibrium, and the level of boron sorption was 108.5 mg/g from a synthetic solution. Several adsorption-desorption cycles were performed using a simple acid-water treatment and evaluated using various kinetic models. The spent adsorbents could be separated easily from the mixture by an external magnetic field. The cost-benefit analysis was performed for the treatment of 72 m(3)/year boron effluent, including five years straight line depreciation charges of equipment. The net profit and standard percentage confirmed that the recovery process is economically feasible.

  7. Relationship Between Soil Boron Adsorption Kinetics and Rape Plant Boron Response

    Institute of Scientific and Technical Information of China (English)

    ZHUDUANWEI; PIMEIMEI; 等

    1997-01-01

    The boron adsorption kinetic experiment in soil by means a flow displacement technique showed that the kinetic data could be described with some mathematic equations.The average values of the coorealtion coefficeint for zero-order,first-order,parabolic diffusion ,Elovich,power function and eponential equations were 0.957,0.982,0.981,0.984,0.981 and 0.902 ,respectively,The correlation between adsorbed boron or its other expression form and time were the highest for first-order ,parabloic diffusion Elovich,and pwer function equations,the second for the zeroorder equation,and the tlowest for the exponential equation.The parabloic diffusion equation fitted well the expermiental results,with the least standard error among the six kinetic equation,showing that the monvemetn of boron from soil solution to soil colloid surface may be controlled by boron diffusion speed.The boron content of rape seedling obtained from soil cultvation was correlated with the rate constants of the kinetic equations.The constants of first-order ,parabloic diffusion,and exponential equaitions were significanlty correlated with the boron content of the crop of NPK treatment at a 95% probaility level ,with correation coeffecients being 0.686,0.691 and 0.64 and 0.641,respectively.In the case of zero-order equation,it Was significant at 99% probability level(r=0.736),These results showed that the adsorption kinetic constants of soil boron were closely related with the rape plant response to boron.

  8. Boron carbide coating deposition on tungsten substrates from atomic fluxes of boron and carbon

    Science.gov (United States)

    Sadovskiy, Y.; Begrambekov, L.; Ayrapetov, A.; Gretskaya, I.; Grunin, A.; Dyachenko, M.; Puntakov, N.

    2016-09-01

    A device used for both coating deposition and material testing is presented in the paper. By using lock chambers, sputtering targets are easily exchanged with sample holder thus allowing testing of deposited samples with high power density electron or ion beams. Boron carbide coatings were deposited on tungsten samples. Methods of increasing coating adhesion are described in the paper. 2 μm boron carbide coatings sustained 450 heating cycles from 100 to 900 C. Ion beam tests have shown satisfactory results.

  9. Multi-dimensional boron transport modeling in subchannel approach: Part II. Validation of CTF boron tracking model and adding boron precipitation model

    Energy Technology Data Exchange (ETDEWEB)

    Ozdemir, Ozkan Emre, E-mail: ozdemir@psu.edu; Avramova, Maria N., E-mail: mna109@psu.edu

    2014-10-15

    Highlights: • Validation of implemented multi-dimensional subchannel boron transport model. • Extension of boron transport model to entrained droplets. • Implementation of boron precipitation model. • Testing of the boron precipitation model under transient condition. - Abstract: The risk of small-break loss of coolant accident (SB-LOCA) and other reactivity initiated transients caused by boron dilution in the light water reactors (LWRs), and the complications of tracking the soluble boron concentration experimentally inside the primary coolant have stimulated the interest in computational studies for accurate boron tracking simulations in nuclear reactors. In Part I of this study, the development and implementation of a multi-dimensional boron transport model with modified Godunov scheme based on a subchannel approach within the COBRA-TF (CTF) thermal-hydraulic code was presented. The modified Godunov scheme approach with a physical diffusion term was determined to provide the most accurate and precise solution. Current paper extends these conclusions and presents the model validation studies against experimental data from the Rossendorf coolant mixing model (ROCOM) test facility. In addition, the importance of the two-phase flow characteristics in modeling boron transient are emphasized, especially during long-term cooling period after the loss of coolant accident (LOCA) condition in pressurized water reactors (PWRs). The CTF capabilities of boron transport modeling are further improved based on the three-field representation of the two-phase flow utilized in the code. The boron transport within entrained droplets is modeled, and a model for predicting the boron precipitation under transient conditions is developed and tested. It is aimed to extend the applicability of CTF to reactor transient simulations, and particularly to a large-break loss of coolant accident (LB-LOCA) analysis.

  10. Synthesis and evaluation of boron folates for Boron-Neutron-Capture-Therapy (BNCT)

    Energy Technology Data Exchange (ETDEWEB)

    Kettenbach, Kathrin; Schieferstein, Hanno; Grunewald, Catrin; Hampel, Gabriele; Schuetz, Christian L. [Mainz Univ. (Germany). Inst. of Nuclear Chemistry; Iffland, Dorothee; Bings, Nicolas H. [Mainz Univ. (Germany). Inst. of Inorganic Chemistry and Analytical Chemistry; Reffert, Laura M. [Hannover Medical School (Germany). Radiopharmaceutical Chemistry; Ross, Tobias L. [Mainz Univ. (Germany). Inst. of Nuclear Chemistry; Hannover Medical School (Germany). Radiopharmaceutical Chemistry

    2015-07-01

    Boron neutron capture therapy (BNCT) employs {sup 10}B-pharmaceuticals administered for the treatment of malignancies, and subsequently irradiated with thermal neutrons. So far, clinical established pharmaceuticals like boron phenylalanine (BPA) or sodium boron mercaptate (BSH) use imperfect (BPA) or passive (BSH) targeting for accumulation at target sites. Due to the need of a selective transportation of boron drugs into cancer cells and sparing healthy tissues, we combined the BNCT approach with the specific and effective folate receptor (FR) targeting concept. The FR is overexpressed on many human carcinomas and provides a selective and specific target for molecular imaging as well as for tumor therapy. We synthesized and characterized a carborane-folate as well as a BSH-folate to study their in vitro characteristics and their potential as new boron-carriers for BNCT. Uptake studies were carried out using human KB cells showing a significant increase of the boron content in cells and demonstrating the successful combination of active FR-targeting and BNCT.

  11. Rapid mass-spectrometric determination of boron isotopic distribution in boron carbide.

    Science.gov (United States)

    Rein, J E; Abernathey, R M

    1972-07-01

    Boron isotopic ratios are measured in boron carbide by thermionic ionization mass spectrometry with no prior chemical separation. A powder blend of boron carbide and sodium hydroxide is prepared, a small portion is transferred to a tantalum filament, the filament is heated to produce sodium borate, and the filament is transferred to the mass spectrometer where the(11)B/(10)B ratio is measured, using the Na(2)BO(2)(+) ion. Variables investigated for their effect on preferential volatilization of (10)B include the sodium hydroxide-boron carbide ratio and the temperature and duration of filament heating. A series of boron carbide pellets containing natural boron, of the type proposed for the control rods of the Fast Flux Test Facility reactor, were analysed with an apparently unbiased result of 4.0560 for the (11)B/(10)B ratio (standard deviation 0.0087). The pellets contained over 3% metal impurities typically found in this material. Time of analysis is 45 min per sample, with one analyst.

  12. The investigation of physical conditions of boron uptake region in proton boron fusion therapy (PBFT)

    Science.gov (United States)

    Jung, Joo-Young; Yoon, Do-Kun; Lee, Heui Chang; Lu, Bo; Suh, Tae Suk

    2016-09-01

    We conducted a quantitative study to identify the effectiveness of proton boron fusion therapy (PBFT). Four simulation scenarios were designed to investigate the escalation in total dose with the proton boron reaction using a Monte Carlo n-particle extended (MCNPX 2.6.0) simulation. The peak integrated dose was obtained for three different physical conditions (i.e., boron uptake region (BUR) thickness, BUR location, and boron concentration) with differing proton beam energy (60-90 MeV). We found that the peak integrated dose was increased by up to 96.62% compared to the pristine proton Bragg-peak. For the synergetic effect to take place with 60-70 MeV proton beam, the BUR had to be at least 0.3 cm thick while spanning the Bragg-peak. Similarly to the thickness, the BUR location needed to be within 0.3 cm from the Bragg-peak when the thickness was maintained at 0.9 cm. An effective proton boron reaction required the boron concentration to be equal to or greater than 14.4 mg/g. These results demonstrate the impact of various physical and beam conditions of the PBFT, which are critical environmental factors for the treatment planning. We envision that this study will advance our understanding of the PBFT, which can be an invaluable treatment method for maximizing the potential of proton therapy.

  13. The investigation of physical conditions of boron uptake region in proton boron fusion therapy (PBFT

    Directory of Open Access Journals (Sweden)

    Joo-Young Jung

    2016-09-01

    Full Text Available We conducted a quantitative study to identify the effectiveness of proton boron fusion therapy (PBFT. Four simulation scenarios were designed to investigate the escalation in total dose with the proton boron reaction using a Monte Carlo n-particle extended (MCNPX 2.6.0 simulation. The peak integrated dose was obtained for three different physical conditions (i.e., boron uptake region (BUR thickness, BUR location, and boron concentration with differing proton beam energy (60–90 MeV. We found that the peak integrated dose was increased by up to 96.62% compared to the pristine proton Bragg-peak. For the synergetic effect to take place with 60–70 MeV proton beam, the BUR had to be at least 0.3 cm thick while spanning the Bragg-peak. Similarly to the thickness, the BUR location needed to be within 0.3 cm from the Bragg-peak when the thickness was maintained at 0.9 cm. An effective proton boron reaction required the boron concentration to be equal to or greater than 14.4 mg/g. These results demonstrate the impact of various physical and beam conditions of the PBFT, which are critical environmental factors for the treatment planning. We envision that this study will advance our understanding of the PBFT, which can be an invaluable treatment method for maximizing the potential of proton therapy.

  14. Identification of a Novel System for Boron Transport: Atr1 Is a Main Boron Exporter in Yeast▿ †

    Science.gov (United States)

    Kaya, Alaattin; Karakaya, Huseyin C.; Fomenko, Dmitri E.; Gladyshev, Vadim N.; Koc, Ahmet

    2009-01-01

    Boron is a micronutrient in plants and animals, but its specific roles in cellular processes are not known. To understand boron transport and functions, we screened a yeast genomic DNA library for genes that confer resistance to the element in Saccharomyces cerevisiae. Thirty boron-resistant transformants were isolated, and they all contained the ATR1 (YML116w) gene. Atr1 is a multidrug resistance transport protein belonging to the major facilitator superfamily. C-terminal green fluorescent protein-tagged Atr1 localized to the cell membrane and vacuole, and ATR1 gene expression was upregulated by boron and several stress conditions. We found that atr1Δ mutants were highly sensitive to boron treatment, whereas cells overexpressing ATR1 were boron resistant. In addition, atr1Δ cells accumulated boron, whereas ATR1-overexpressing cells had low intracellular levels of the element. Furthermore, atr1Δ cells showed stronger boron-dependent phenotypes than mutants deficient in genes previously reported to be implicated in boron metabolism. ATR1 is widely distributed in bacteria, archaea, and lower eukaryotes. Our data suggest that Atr1 functions as a boron efflux pump and is required for boron tolerance. PMID:19414602

  15. Boron nanoparticles inhibit turnour growth by boron neutron capture therapy in the murine B16-OVA model

    DEFF Research Database (Denmark)

    Petersen, Mikkel Steen; Petersen, Charlotte Christie; Agger, Ralf;

    2008-01-01

    Background: Boron neutron capture therapy usually relies on soluble, rather than particulate, boron compounds. This study evaluated the use of a novel boron nanoparticle for boron neutron capture therapy. Materials and Methods: Two hundred and fifty thousand B16-OVA tumour cells, pre......-incubated with boron nanoparticles for 12 hours, were injected subcutaneously into C57BL16J mice. The tumour sites were exposed to different doses of neutron radiation one, four, or eight days after tumour cell inoculation. Results: When the tumour site was irradiated with thermal neutrons one day after injection......, tumour growth was delayed and the treated mice survived longer than untreated controls (median survival time 20 days (N=8) compared with 10 days (N=7) for untreated mice). Conclusion: Boron nanoparticles significantly delay the growth of an aggressive B16-OVA tumour in vivo by boron neutron capture...

  16. Composite Reinforcement using Boron Nitride Nanotubes

    Science.gov (United States)

    2016-11-15

    ApprovedOMB No. 0704-0188 The public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for...nitride nanotubes change with the presence of atomic oxygen were also carried out. 15.  SUBJECT TERMS Nanotubes, Boron Nitride, Composites, Theoretical

  17. Pechmann Reaction Promoted by Boron Trifluoride Dihydrate

    Directory of Open Access Journals (Sweden)

    J. Mezger

    2005-08-01

    Full Text Available The Pechmann reaction of substituted phenols 1a-e with methyl acetoacetate (2 can be activated by boron trifluoride dihydrate (3 to give the corresponding 4-methyl- coumarin derivatives 4a-e in excellent yield (98-99 %.

  18. NEW ADVANCES IN BORON SOIL CHEMISTRY

    Science.gov (United States)

    Boron is an essential plant micronutrient for which the range between deficiency and toxicity is narrower than for any other nutrient element. Plants respond directly to the amount of B in soil solution and only indirectly to the amount of B adsorbed on soil particle surfaces. ...

  19. New insight into pecan boron nutrition

    Science.gov (United States)

    Alternate bearing by individual pecan [Carya illinoinensis (Wangenh.) K. Koch] trees is problematic for nut producers and processors. There are many unknowns regarding alternate bearing physiology, such as the relationship between boron and fruit set, nutmeat quality, and kernel maladies. Evidence...

  20. NEW ADVANCES IN BORON SOIL CHEMISTRY - Paper

    Science.gov (United States)

    Boron is an essential plant micronutrient for which the range between deficiency and toxicity is narrower than for any other nutrient element. Plants respond directly to the amount of B in soil solution and only indirectly to the amount of B adsorbed on soil particle surfaces. ...

  1. Catalytic Asymmetric Synthesis of Phosphine Boronates.

    Science.gov (United States)

    Hornillos, Valentín; Vila, Carlos; Otten, Edwin; Feringa, Ben L

    2015-06-26

    The first catalytic enantioselective synthesis of ambiphilic phosphine boronate esters is presented. The asymmetric boration of α,β-unsaturated phosphine oxides catalyzed by a copper bisphosphine complex affords optically active organoboronate esters that bear a vicinal phosphine oxide group in good yields and high enantiomeric excess. The synthetic utility of the products is demonstrated through stereospecific transformations into multifunctional optically active compounds.

  2. Boron carbide morphology changing under purification

    Science.gov (United States)

    Rahmatullin, I. A.; Sivkov, A. A.

    2015-10-01

    Boron carbide synthesized by using coaxial magnetoplasma accelerator with graphite electrodes was purified by two different ways. XRD-investigations showed content changing and respectively powder purification. Moreover TEM-investigations demonstrated morphology changing of product under purification that was discussed in the work.

  3. NEW ADVANCES IN BORON SOIL CHEMISTRY

    Science.gov (United States)

    Boron is an essential plant micronutrient for which the range between deficiency and toxicity is narrower than for any other nutrient element. Plants respond directly to the amount of B in soil solution and only indirectly to the amount of B adsorbed on soil particle surfaces. ...

  4. NEW ADVANCES IN BORON SOIL CHEMISTRY - Paper

    Science.gov (United States)

    Boron is an essential plant micronutrient for which the range between deficiency and toxicity is narrower than for any other nutrient element. Plants respond directly to the amount of B in soil solution and only indirectly to the amount of B adsorbed on soil particle surfaces. ...

  5. Novel Boron Based Multilayer Thermal Neutron Detector

    CERN Document Server

    SCHIEBER, M

    2010-01-01

    The detector contains four or more layers of natural Boron absorbing thermal neutrons. Thickness of a layer is 0.4 - 1.2 mg/cm2. The layers are deposited on one or on both sides of a metal surface used as contacts. Between the absorbing layers there are gas-filled gaps 3 - 6 mm thick. Electric field of 100 - 200 V/cm is applied to the gas-filled gaps. Natural Boron contains almost 20% of 10B isotope. When atoms of 10B capture a thermal neutron, nuclear reaction occurs, as a result of which two heavy particles - alpha particle and ion 7Li - from the thin absorber layer are emitted in opposing sides. One of the two particles penetrates into gas-filled gap between Boron layers and ionizes the gas. An impulse of electric current is created in the gas-filled gap actuated by the applied electric field. The impulse is registered by an electronic circuit. We have made and tested detectors containing from two to sixteen layers of natural Boron with an efficiency of thermal neutron registration from 2.9% to 12.5% accor...

  6. Substitution reactions at boron atoms in metallacarboranes

    Energy Technology Data Exchange (ETDEWEB)

    Bregadze, Vladimir I; Timofeev, Sergei V; Sivaev, Igor B; Lobanova, Irina A [A.N. Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Moscow (Russian Federation)

    2004-05-31

    Data on substitution reactions at boron atoms in 10-12-vertex metallacarboranes, which are of fundamental and applied significance, are generalised. The possible mechanisms of substitution reactions and the influence of the metal fragment on substitution positions in the polyhedron are discussed.

  7. Assessment of Boron Steels for Army Use

    Science.gov (United States)

    1978-11-01

    transform the microstructure from austenite to the lower tempera- ture transformation product martensite (lower bainite may also be satisfactory for... bainite , carbides, or pearlite. Thus, as long as low tem- perature transformation products are desired (martensite and lower bainite ), boron 13

  8. Investigating the Boron Requirement of Plants.

    Science.gov (United States)

    Bohnsack, Charles W.

    1991-01-01

    This article describes a simple and rapid method for using summer squash to investigate born deficiency in plants. Author asserts that students are likely to feel challenged by laboratory exercises and projects that focus on the role boron plays in plant growth because it is an unresolved problem in biology. (PR)

  9. Influence of pollution of boron chlorinity ratio

    Digital Repository Service at National Institute of Oceanography (India)

    Narvekar, P.V.; Zingde, M.D.

    Presence of boron in domestic wastewater has resulted in high B/CI ratio at some locations in the coastal water around Bombay. A widest range (0.215-0.281) of B/CI was observed at a location with high influence of wastewater release. The mean B...

  10. Trapping and Sympathetic Cooling of Boron Ions

    CERN Document Server

    Rugango, Rene; Shu, Gang; Brown, Kenneth R

    2016-01-01

    We demonstrate the trapping and sympathetic cooling of B$^{+}$ ions in a Coulomb crystal of laser-cooled Ca$^{+}$, We non-destructively confirm the presence of the both B$^+$ isotopes by resonant excitation of the secular motion. The B$^{+}$ ions are loaded by ablation of boron and the secular excitation spectrum also reveals features consistent with ions of the form B$_{n}^{+}$.

  11. Powdered Hexagonal Boron Nitride Reducing Nanoscale Wear

    Science.gov (United States)

    Chkhartishvili, L.; Matcharashvili, T.; Esiava, R.; Tsagareishvili, O.; Gabunia, D.; Margiev, B.; Gachechiladze, A.

    2013-05-01

    A morphology model is suggested for nano-powdered hexagonal boron nitride that can serve as an effective solid additive to liquid lubricants. It allows to estimate the specific surface, that is a hard-to-measure parameter, based on average size of powder particles. The model can be used also to control nanoscale wear processes.

  12. Risks of low dose ionising radiation exposures Riesgos derivados de la exposición a dosis bajas de radiación ionizante

    National Research Council Canada - National Science Library

    Almudena Real Gallego

    2010-01-01

    ... by ionising radiation, with special emphasis on those effects occurring after low dose exposures.La radiación ionizante ha mostrado tener diversas aplicaciones beneficiosas para el hombre, pero...

  13. Studies for the application of boron neutron capture therapy to the treatment of differentiated thyroid cancer

    Energy Technology Data Exchange (ETDEWEB)

    Dagrosa, A., E-mail: dagrosa@cnea.gov.ar [Department of Radiobiology, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina)] [National Research Council of Argentina (CONICET), Rivadavia 1917, (1033) Buenos Aires (Argentina); Carpano, M. [Department of Radiobiology, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina); Perona, M. [Department of Radiobiology, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina)] [National Research Council of Argentina (CONICET), Rivadavia 1917, (1033) Buenos Aires (Argentina); Thomasz, L. [Department of Radiobiology, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina); Nievas, S. [Department of Chemistry, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina); Cabrini, R. [Department of Radiobiology, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina); Juvenal, G. [Department of Radiobiology, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina)] [National Research Council of Argentina (CONICET), Rivadavia 1917, (1033) Buenos Aires (Argentina); Pisarev, M. [Department of Radiobiology, National Atomic Energy Commission (CNEA), Av General Paz 1499, San Martin (1560) (Argentina)] [National Research Council of Argentina (CONICET), Rivadavia 1917, (1033) Buenos Aires (Argentina)] [Department of Biochemistry, UBA School of Medicine (Argentina)

    2011-12-15

    The aim of these studies was to evaluate the possibility of treating differentiated thyroid cancer by BNCT. These carcinomas are well controlled with surgery followed by therapy with {sup 131}I; however, some patients do not respond to this treatment. BPA uptake was analyzed both in vitro and in nude mice implanted with cell lines of differentiated thyroid carcinoma. The boron intracellular concentration in the different cell lines and the biodistribution studies showed the selectivity of the BPA uptake by this kind of tumor.

  14. Emission Line Galaxies and Active Galactic Nuclei in WINGS clusters

    CERN Document Server

    Marziani, P; Bettoni, D; Poggianti, B M; Moretti, A; Fasano, G; Fritz, J; Cava, A; Varela, J; Omizzolo, A

    2016-01-01

    We present the analysis of the emission line galaxies members of 46 low redshift (0.04 < z < 0.07) clusters observed by WINGS (WIde-field Nearby Galaxy cluster Survey, Fasano et al. 2006). Emission line galaxies were identified following criteria that are meant to minimize biases against non-star forming galaxies and classified employing diagnostic diagrams. We have examined the emission line properties and frequencies of star forming galaxies, transition objects and active galactic nuclei (AGNs: LINERs and Seyferts), unclassified galaxies with emission lines, and quiescent galaxies with no detectable line emission. A deficit of emission line galaxies in the cluster environment is indicated by both a lower frequency with respect to control samples, and by a systematically lower Balmer emission line equivalent width and luminosity (up to one order of magnitude in equivalent width with respect to control samples for transition objects) that implies a lower amount of ionised gas per unit mass and a lower s...

  15. Eddy covariance flux measurements of ammonia by high temperature chemical ionisation mass spectrometry

    Directory of Open Access Journals (Sweden)

    J. Sintermann

    2011-03-01

    Full Text Available A system for fast ammonia (NH3 measurements with chemical ionisation mass spectrometry (CIMS based on a commercial Proton Transfer Reaction-Mass Spectrometer (PTR-MS is presented. It uses electron transfer reaction as ionisation pathway and features a drift tube of polyetheretherketone (PEEK and silica-coated steel. Heating the instrumental inlet and the drift tube to 180 °C enabled an effective time resolution of ~1 s and made it possible to apply the instrument for eddy covariance (EC measurements. EC fluxes of NH3 were measured over two agricultural fields in Oensingen, Switzerland, following fertilisations with cattle slurry. Air was aspirated close to a sonic anemometer at a flow of 100 STP L min−1 and was directed through a 23 m long 1/2" PFA tube heated to 150 °C to an air-conditioned trailer where the gas was sub-sampled from the large bypass stream. This setup minimised damping of fast NH3 concentration changes between the sampling point and the actual measurement. High-frequency attenuation loss of the NH3 fluxes of 20 to 40% was quantified and corrected for using an empirical ogive method. The instrumental NH3 background signal showed a minor interference with H2O which was characterised in the laboratory. The resulting correction of the NH3 flux after slurry spreading was less than 1‰. The flux detection limit of the EC system was about 5 ng m−2 s−1 while the accuracy of individual flux measurements was estimated 16% for the high-flux regime during these experiments. The NH3 emissions after broad spreading of the slurry showed an initial maximum of 150 μg m−2 s−1 with a fast decline in the following hours.

  16. Ionisation differential cross section measurements for N2 at low incident energy in coplanar and non-coplanar geometries

    Science.gov (United States)

    Sakaamini, Ahmad; Amami, Sadek; Murray, Andrew James; Ning, Chuangang; Madison, Don

    2016-10-01

    Ionisation triple differential cross sections have been determined experimentally and theoretically for the neutral molecule N2 over a range of geometries from coplanar to the perpendicular plane. Data were obtained at incident electron energies ∼10 and ∼20 eV above the ionisation potential of the 3σ g, 1π u and 2σ g states, using both equal and non-equal outgoing electron energies. The data were taken with the incident electron beam in the scattering plane (ψ = 0°), at 45° to this plane and orthogonal to the plane (ψ = 90°). The set of nine measured differential cross sections at a given energy were then inter-normalised to each other. The data are compared to new calculations using various distorted wave methods, and differences between theory and experiment are discussed.

  17. Serum ionised calcium and cardiovascular disease in 45-years old men and women followed for 18 years

    DEFF Research Database (Denmark)

    Ogard, Christina Gerlach; Petersen, Janne; Jørgensen, Torben

    2006-01-01

    a health survey in 1981 in Copenhagen had ionised serum calcium and different cardiovascular risk factors measured. The participants were followed until 1999 in The National Hospital Patients Registry and The National Death Registry in Denmark regarding the diagnosis ischemic heart disease (IHD...... to persons in the lower quintiles. The increased risk disappeared when gender and cardiovascular confounders were included in a Cox proportional hazards analysis (p=0.20 for IHD and p=0.50 for CVD, respectively). In a separate analysis of men and IHD the result remained insignificant (p=0.07). Conclusions......High level of total serum calcium within the normal range has been associated with increased cardiovascular risk. We wanted to evaluate whether the physiological active ionised form of calcium also was a risk factor for cardiovascular disease (CVD). Methods: A total of 974 participants from...

  18. Photoluminescence study of 1018 meV defect lines from ion-implanted silicon

    CERN Document Server

    Lee, H S; Seong, E Z; Kim, S M; Lim, H J

    1999-01-01

    We investigated the defects of ion-implanted silicon with boron and argon ions using photoluminescence method. The 1018 meV line, so called I sub 1 line, and its phonon side bands were observed in both boron- and argon-implanted silicon crystals. In argon-implanted silicon crystals, we observed 1009 meV line (I sub r - Ar) and its phonon side bands which arose from argon-I sub 1 complex in addition to the splitting of the I sub 1 line. Annealing temperature dependence of the intensities of the I sub 1 and I sub 1 -Ar lines in argon-implanted silicon was very similar for both Czochralski and float zone silicon crystals whereas that of boron-implanted silicon was very different between the two growing methods. We discussed on the origin of the defects responsible for the I sub 1 and I sub 1 - Ar lines.

  19. Potential errors in relative dose measurements in kilovoltage photon beams due to polarity effects in plane-parallel ionisation chambers.

    Science.gov (United States)

    Dowdell, S; Tyler, M; McNamara, J; Sloan, K; Ceylan, A; Rinks, A

    2016-11-15

    Plane-parallel ionisation chambers are regularly used to conduct relative dosimetry measurements for therapeutic kilovoltage beams during commissioning and routine quality assurance. This paper presents the first quantification of the polarity effect in kilovoltage photon beams for two types of commercially available plane-parallel ionisation chambers used for such measurements. Measurements were performed at various depths along the central axis in a solid water phantom and for different field sizes at 2 cm depth to determine the polarity effect for PTW Advanced Markus and Roos ionisation chambers (PTW-Freiburg, Germany). Data was acquired for kilovoltage beams between 100 kVp (half-value layer (HVL)  =  2.88 mm Al) and 250 kVp (HVL  =  2.12 mm Cu) and field sizes of 3-15 cm diameter for 30 cm focus-source distance (FSD) and 4  ×  4 cm(2)-20  ×  20 cm(2) for 50 cm FSD. Substantial polarity effects, up to 9.6%, were observed for the Advanced Markus chamber compared to a maximum 0.5% for the Roos chamber. The magnitude of the polarity effect was observed to increase with field size and beam energy but was consistent with depth. The polarity effect is directly influenced by chamber design, with potentially large polarity effects for some plane-parallel ionisation chambers. Depending on the specific chamber used, polarity corrections may be required for output factor measurements of kilovoltage photon beams. Failure to account for polarity effects could lead to an incorrect dose being delivered to the patient.

  20. Potential errors in relative dose measurements in kilovoltage photon beams due to polarity effects in plane-parallel ionisation chambers

    Science.gov (United States)

    Dowdell, S.; Tyler, M.; McNamara, J.; Sloan, K.; Ceylan, A.; Rinks, A.

    2016-12-01

    Plane-parallel ionisation chambers are regularly used to conduct relative dosimetry measurements for therapeutic kilovoltage beams during commissioning and routine quality assurance. This paper presents the first quantification of the polarity effect in kilovoltage photon beams for two types of commercially available plane-parallel ionisation chambers used for such measurements. Measurements were performed at various depths along the central axis in a solid water phantom and for different field sizes at 2 cm depth to determine the polarity effect for PTW Advanced Markus and Roos ionisation chambers (PTW-Freiburg, Germany). Data was acquired for kilovoltage beams between 100 kVp (half-value layer (HVL)  =  2.88 mm Al) and 250 kVp (HVL  =  2.12 mm Cu) and field sizes of 3-15 cm diameter for 30 cm focus-source distance (FSD) and 4  ×  4 cm2-20  ×  20 cm2 for 50 cm FSD. Substantial polarity effects, up to 9.6%, were observed for the Advanced Markus chamber compared to a maximum 0.5% for the Roos chamber. The magnitude of the polarity effect was observed to increase with field size and beam energy but was consistent with depth. The polarity effect is directly influenced by chamber design, with potentially large polarity effects for some plane-parallel ionisation chambers. Depending on the specific chamber used, polarity corrections may be required for output factor measurements of kilovoltage photon beams. Failure to account for polarity effects could lead to an incorrect dose being delivered to the patient.

  1. Synthesis and characterization of ammonium phosphate fertilizers with boron

    Directory of Open Access Journals (Sweden)

    ANGELA MAGDA

    2010-07-01

    Full Text Available The concentration of boron, an essential micronutrient for plants, presents a narrow range between deficiency and toxicity. In order to provide the boron requirement for plants, and to avoid toxicity problems, boron compounds are mixed with basic fertilizers. Sodium borate pentahydrate was used as a boron source. Ammonium orthophosphates fertilizers with boron were prepared by neutralizing phosphoric acid with ammonia and addition of variable amounts of sodium tetraborate pentahydrate to the reaction mixture at a NH3:H3PO4 molar ratio of 1.5. The fertilizers obtained with boron contents ranging from 0.05 to 1 % (w/w were fully characterized by chemical analysis, thermal analysis, X-ray diffraction and infrared spectrophotometry. The studies showed that up to 500 °C, regardless of the boron content, no significant changes concerning thermal stability and nutritional properties occurred. Above 500 °C, an increase of thermal stability with an increase of the boron content was observed. X-Ray diffraction of a heat-treated sample containing 5 % (w/w boron indicated the appearance of boron orthophosphate, BPO4, as a new crystalline phase, and the disappearance of the previous structures above 500 °C, which explains the increase in thermal stability.

  2. Higher boron rejection with a new TFC forward osmosis membrane

    KAUST Repository

    Valladares Linares, Rodrigo

    2014-07-17

    Due to the stringent limits for boron in drinking and irrigation water, water treatment facilities have to incur additional treatment to remove boron down to a safe concentration. Forward osmosis (FO) is a membrane technology that may reduce the energy required to remove boron present in seawater. In direct FO desalination hybrid systems, fresh water is recovered from seawater using a recoverable draw solution, FO membranes are expected to show high boron rejection. This study focuses on determining the boron rejection capabilities of a new generation thin-film composite (TFC) FO membrane compared to a first generation cellulose triacetate (CTA) FO membrane. The effects of water permeate flux, membrane structure, draw solute charge, and reverse solute flux on boron rejection were determined. For TFC and CTA FO membranes, experiments showed that when similar operating conditions are applied (e.g. membrane type and draw solute type) boron rejection decreases with increase in permeate flux. Reverse draw solute flux and membrane fouling have no significant impact on boron rejection. Compared to the first generation CTA FO membrane operated at the same conditions, the TFC FO membrane showed a 40% higher boron rejection capability and a 20% higher water flux. This demonstrates the potential for boron removal for new generation TFC FO membranes. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

  3. Effects of auxin and boron on the rooting of Laurus nobilis L. stem cuttings

    Directory of Open Access Journals (Sweden)

    Fernando Perez Leal

    2004-05-01

    Full Text Available The purpose of this study was to evaluate the effect of indolebutyric acid (IBA, applied with or without boric acid, on rooting laurel (Laurus nobilis L. stem cuttings. The cuttings (15cm that presented two apical leaves were collected from the apexes. They were treated with IBA 0, 50, 150 and 300 mg L-1, with or without boron 150 mg mL-1, for 24 hours. After the treatments, the cuttings were cultivated in polystyrene trays with carbonized rice linings and maintained under intermittent nebulization for 70 days when the percentages for rooting, stem cuttings with callus, and live and dead cuttings, root numbers and root lengths were evaluated. The results showed that IBA 50 mg L-1, IBA 150 and 300mg L-1 with boron enhanced the rooting percentage. The treatment with IBA 150 mg L-1 showed the highest root number in stem cuttings.

  4. Phonon symmetries in hexagonal boron nitride probed by incoherent light emission

    Science.gov (United States)

    Vuong, T. Q. P.; Cassabois, G.; Valvin, P.; Jacques, V.; Van Der Lee, A.; Zobelli, A.; Watanabe, K.; Taniguchi, T.; Gil, B.

    2017-03-01

    Layered compounds are stacks of weakly bound two-dimensional atomic crystals, with a prototypal hexagonal structure in graphene, transition metal dichalcogenides and boron nitride. This crystalline anisotropy results in vibrational modes with specific symmetries depending on the in-plane or out-of-plane atomic displacements. We show that polarization-resolved photoluminescence measurements in hexagonal boron nitride reflect the phonon symmetries in this layered semiconductor. Experiments performed with a detection on the sample edge, perpendicular to the c-axis, reveal the strong polarization-dependence of the emission lines corresponding to the recombination assisted by the three acoustic phonon modes. We elucidate the dipole orientation of the fundamental indirect exciton. We demonstrate evidence of the so-far missing phonon replica due to the optical out-of-plane phonon mode.

  5. Antitumor potential induction and free radicals production in melanoma cells by Boron Neutron Capture Therapy

    Energy Technology Data Exchange (ETDEWEB)

    Faiao-Flores, F. [Biochemical and Biophysical Laboratory, Butantan Institute, 1500 Vital Brasil Avenue, Sao Paulo (Brazil)] [Faculty of Medicine, University of Sao Paulo, 455 Doutor Arnaldo Avenue, Sao Paulo (Brazil); Coelho, P.R.P.; Muniz, R.O.R.; Souza, G.S. [Institute for Nuclear and Energy Research, 2242 Lineu Prestes Avenue, Sao Paulo (Brazil); Arruda-Neto, J. [Physics Institute, University of Sao Paulo, 187 Matao Street, Sao Paulo (Brazil)] [FESP, Sao Paulo Engineering School, 5520 Nove de Julho Avenue, Sao Paulo (Brazil); Maria, Durvanei A., E-mail: durvaneiaugusto@yahoo.com.br [Biochemical and Biophysical Laboratory, Butantan Institute, 1500 Vital Brasil Avenue, Sao Paulo (Brazil)

    2011-12-15

    Antiproliferative and oxidative damage effects occurring in Boron Neutron Capture Therapy (BNCT) in normal fibroblasts and melanoma cell lines were analyzed. Melanoma cells and normal fibroblasts were treated with different concentrations of Boronophenylalanine and irradiated with thermal neutron flux. The cellular viability and the oxidative stress were determined. BNCT induced free radicals production and proliferative potential inhibition in melanoma cells. Therefore, this therapeutic technique could be considered efficient to inhibit growth of melanoma with minimal effects on normal tissues. - Highlights: Black-Right-Pointing-Pointer Boron Neutron Capture Therapy (BNCT) induces melanoma cell death. Black-Right-Pointing-Pointer BNCT stimulates free radicals production and proliferative inhibition in melanoma cells. Black-Right-Pointing-Pointer It produces tumor membrane degeneration and destruction with apoptotic bodies formation. Black-Right-Pointing-Pointer This therapy damages tumor cells selectively, with minimum effects on normal adjacent tissue.

  6. Mapping the ionised gas around the luminous QSO HE 1029-1401: Evidence for minor merger events?

    CERN Document Server

    Husemann, B; Wisotzki, L; Jahnke, K; Kupko, D; Nugroho, D; Schramm, M

    2010-01-01

    We present VIMOS integral field spectroscopy of the brightest radio-quiet QSO on the southern sky HE 1029-1401 at a redshift of z=0.086. Standard decomposition techniques for broad-band imaging are extended to integral field data in order to deblend the QSO and host emission. We perform a tentative analysis of the stellar continuum finding a young stellar population (<100Myr) or a featureless continuum embedded in an old stellar population (10Gyr) typical for a massive elliptical galaxy. The stellar velocity dispersion of sigma_*=320\\pm90 km/s and the estimated black hole mass log(M_BH/M_sun)=8.7\\pm0.3 are consistent with the local M_BH-sigma_* relation within the errors. For the first time we map the two-dimensional ionised gas distribution and the gas velocity field around HE 1029-1401. While the stellar host morphology is purely elliptical we find a highly structured distribution of ionised gas out to 16 kpc from the QSO. The gas is highly ionised solely by the QSO radiation and has a significantly lowe...

  7. Calculs de doses générées par les rayonnements ionisants principes et utilitaires

    CERN Document Server

    Vivier, Alain

    2012-01-01

    Cet ouvrage s'adresse aux utilisateurs de sources de rayonnements ionisants : techniciens et ingénieurs ou personnes compétentes en radioprotection, médecins, chercheurs, concepteurs... Les contraintes croissantes liées à la radioprotection rendent indispensable l'utilisation de codes (ou programmes) de calculs pour évaluer les débits de dose générée par les sources de rayonnements ionisants. De nombreux codes existent mais ils sont souvent relativement complexes à mettre en oeuvre et restent réservés aux bureaux d'études. En outre, ces codes sont souvent des "boîtes noires " qui ne permettent pas de comprendre la physique sous-jacente. L'objectif de cet ouvrage est double. Exposer les principes physiques permettant de comprendre les phénomènes à l'oeuvre lorsque la matière est irradiée par des rayonnements ionisants. Il devient ainsi possible de développer un sens physique pour appréhender ces phénomènes, alors même que nos propres sens sont impuissants à en percevoir la cause et le...

  8. An isotopic analysis of ionising radiation as a source of sulphuric acid

    Directory of Open Access Journals (Sweden)

    M. B. Enghoff

    2012-06-01

    Full Text Available Sulphuric acid is an important factor in aerosol nucleation and growth. It has been shown that ions enhance the formation of sulphuric acid aerosols, but the exact mechanism has remained undetermined. Furthermore some studies have found a deficiency in the sulphuric acid budget, suggesting a missing source. In this study the production of sulphuric acid from SO2 through a number of different pathways is investigated. The production methods are standard gas phase oxidation by OH radicals produced by ozone photolysis with UV light, liquid phase oxidation by ozone, and gas phase oxidation initiated by gamma rays. The distributions of stable sulphur isotopes in the products and substrate were measured using isotope ratio mass spectrometry. All methods produced sulphate enriched in 34S and we find an enrichment factor (δ34S of 8.7 ± 0.4‰ (1 standard deviation for the UV-initiated OH reaction. Only UV light (Hg emission at 253.65 nm produced a clear non-mass-dependent excess of 33S. The pattern of isotopic enrichment produced by gamma rays is similar, but not equal, to that produced by aqueous oxidation of SO2 by ozone. This, combined with the relative yields of the experiments, suggests a mechanism in which ionising radiation may lead to hydrated ion clusters that serve as nanoreactors for S(IV to S(VI conversion.

  9. An isotope view on ionising radiation as a source of sulphuric acid

    Directory of Open Access Journals (Sweden)

    M. B. Enghoff

    2012-02-01

    Full Text Available Sulphuric acid is an important factor in aerosol nucleation and growth. It has been shown that ions enhance the formation of sulphuric acid aerosols, but the exact mechanism has remained undetermined. Furthermore some studies have found a deficiency in the sulphuric acid budget, suggesting a missing source. In this study the production of sulphuric acid from SO2 through a number of different pathways is investigated. The production methods are standard gas phase oxidation by OH radicals produced by ozone photolysis with UV light, liquid phase oxidation by ozone, and gas phase oxidation initiated by gamma rays. The distributions of stable sulphur isotopes in the products and substrate were measured using isotope ratio mass spectrometry. All methods produced sulphate enriched in 34S and we find a δ34S value of 8.7 ± 0.4‰ (1 standard deviation for the UV-initiated OH reaction. Only UV light (Hg emission at 253.65 nm produced a clear non-mass-dependent excess of 33S. The pattern of isotopic enrichment produced by gamma rays is similar, but not equal, to that produced by aqueous oxidation of SO2 by ozone. This, combined with the relative yields of the experiments, suggests a mechanism in which ionising radiation may lead to hydrated ion clusters that serve as nanoreactors for S(IV to S(VI conversion.

  10. Les neuropeptides gastro-intestinaux cibles des effets des rayonnements ionisants : altérations fonctionnelles

    Science.gov (United States)

    Linard, C.; Esposito, V.; Wysocki, J.; Griffiths, N. M.

    1998-04-01

    The symptoms associated with exposure to ionizing radiation are nausea, vomiting, diarrhoea. The response of the gut is complex involving modifications of motility and fluid and electrolyte transport. Gastrointestinal regulatory peptides have an important role in these functions. This study showed that radiation-induced tissue variations of neuropeptides have some repercussions on intestinal biological activity of these peptides soon after irradiation. In addition such modifications are also seen a few years after irradiation. Les symptômes associés à l'exposition aux rayonnements ionisants sont des nausées, vomissements et diarrhées. La réponse du système digestif est complexe, impliquant des modifications de la motilité et du transport d'eau et d'électrolytes. les neuropeptides gastro-intestinaux ont un rôle important dans ces fonctions. Cette étude montre que les variations tissulaires de ces neuropeptides induites par l'irradiation ont des répercussions sur l'activité biologique intestinale pour des temps précoces mais que ces perturbations sont encore visibles quelques années après l'irradiation.

  11. Determination of moxonidine in human plasma by liquid chromatography-electrospray ionisation-mass spectrometry.

    Science.gov (United States)

    Zhao, Luhua; Ding, Li; Wei, Xin

    2006-01-23

    A sensitive and specific liquid chromatography-electrospray ionisation-mass spectrometry (LC-ESI-MS) method has been developed and validated for the identification and quantification of moxonidine in human plasma. After the addition of clonidine-HCl, the internal standard (IS) and sodium hydrogen carbonate, plasma samples were extracted using 5 mL ethyl acetate. The compounds were separated on a Lichrospher ODS (5 microm, 250 mm x 4.6 mm) column using an elution system of 10 mmol/L ammonium acetate buffer-methanol (20:80 v/v) as the mobile phase. Analytes were determined using electrospary ionization in a single quadrupole mass spectrometer. LC-ESI-MS was performed in the selected-ion monitoring (SIM) mode using target ions at m/z: 242.2 for moxonidine and m/z: 230.1 for the IS. The method has shown to be sensitive and specific by testing six different blank plasma batches. Linearity was established for the range of concentrations 0.01976-9.88 ng/mL with a coefficient of correlation (r) of 0.9999. The lower limit of quantification (LOQ) was identifiable and reproducible at 0.01976 ng/mL. The method has been successfully applied to study the pharmacokinetics of moxonidine in healthy male Chinese volunteers.

  12. A gas ionisation Direct-STIM detector for MeV ion microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Norarat, Rattanaporn, E-mail: rattanaporn@rmutl.ac.th [University of Applied Sciences (HES-SO), Haute Ecole Arc Ingénierie, Eplatures-Gris 17, CH-2300 La Chaux-de-Fonds (Switzerland); Faculty of Science and Agriculture, Rajamangala University of Technology Lanna, Chiang Rai, 57120 Chiang Rai (Thailand); Department of Physics, University of Jyväskylä, P.O. Box 35, Jyväskylä FI-40014 (Finland); Guibert, Edouard; Jeanneret, Patrick; Dellea, Mario; Jenni, Josef [University of Applied Sciences (HES-SO), Haute Ecole Arc Ingénierie, Eplatures-Gris 17, CH-2300 La Chaux-de-Fonds (Switzerland); Roux, Adrien; Stoppini, Luc [Tissue Engineering Laboratory, Campus Biotech, Chemin des Mines 9, Geneva (Switzerland); Whitlow, Harry J. [University of Applied Sciences (HES-SO), Haute Ecole Arc Ingénierie, Eplatures-Gris 17, CH-2300 La Chaux-de-Fonds (Switzerland)

    2015-04-01

    Direct-Scanning Transmission Ion Microscopy (Direct-STIM) is a powerful technique that yields structural information in sub-cellular whole cell imaging. Usually, a Si p-i-n diode is used in Direct-STIM measurements as a detector. In order to overcome the detrimental effects of radiation damage which appears as a broadening in the energy resolution, we have developed a gas ionisation detector for use with a focused ion beam. The design is based on the ETH Frisch grid-less off-axis Geiger–Müller geometry. It is developed for use in a MeV ion microscope with a standard Oxford Microbeams triplet lens and scanning system. The design has a large available solid angle for other detectors (e.g. proton induced fluorescence). Here we report the performance for imaging ReNcells VM with μm resolution where energy resolutions of <24 keV fwhm could be achieved for 1 MeV protons using isobutane gas.

  13. Complete Ionisation of the Neutral Gas in High Redshift Radio Galaxies and Quasars

    CERN Document Server

    Curran, S J

    2012-01-01

    Cool neutral gas provides the raw material for all star formation in the Universe, and yet, from a survey of the hosts of high redshift radio galaxies and quasars, we find a complete dearth of atomic (HI 21-cm) and molecular (OH, CO, HCO+ & HCN) absorption at redshifts z > 3. Upon a thorough analysis of the optical photometry, we find that all of our targets have ionising ultra-violet continuum luminosities of logL > 23 W/Hz. We therefore attribute this deficit to the traditional optical selection of targets biasing surveys towards the most ultra-violet luminous objects, where the intense radiation excites the neutral gas to the point where it cannot engage in star formation. However, this hypothesis does not explain why there is a critical luminosity, rather than a continuum where the detections gradually become fewer and fewer as the harshness of the radiation increases. We show that by placing a quasar within a galaxy of gas there is always a finite ultra-violet luminosity above which all of the gas is...

  14. Impact of chronic, low-level ionising radiation exposure on terrestrial invertebrates

    Energy Technology Data Exchange (ETDEWEB)

    Hingston, J.; Wood, M.D.; Copplestone, D.; Zinger, I. [Liverpool Univ., School of Biological Sciences, Merseyside (United Kingdom)

    2004-07-01

    There is a need to confirm that the environment is being adequately protected from the mixture of contaminants released into it. In the field of environmental radioactivity, tools have been developed to assess the impacts of ionising radiation on wildlife. The scientific data upon which these assessments are based is, however, lacking. New documentation has been produced by the UK Environment Agency to provide guidelines on structuring experiments (using environmentally relevant doses) and select suitable non-human species and endpoints for study. It is anticipated that this documentation will be used to direct future experiments in this field. This paper presents the results of the first of these experiments. Numbers of the earthworm Eisenia fetida and the wood louse Porcellio scaber were segregated and constantly exposed to one of six radiation doses (background, 0.1, 0.4, 1.5, 4.0 and 8.0 mGyh{sup -1}) for a total of 16 and 14 weeks respectively. The endpoints of mortality, number of viable offspring and average weight of an individual were recorded and the results of this study will be discussed here. (author)

  15. Effect of penetrating ionising radiation on the mechanical properties of pericardium

    Energy Technology Data Exchange (ETDEWEB)

    Daar, Eman, E-mail: e.daar@surrey.ac.u [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom); Woods, E. [Royal Free Hampstead NHS Trust, Pond Street, Hampstead, London NW3 2QG (United Kingdom); Keddie, J.L. [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom); Nisbet, A. [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom); Royal Surrey County Hospital, Guildford (United Kingdom); Bradley, D.A. [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom)

    2010-07-21

    The pericardium is an anistropic composite material made up of collagen and elastin fibres embedded in an amorphous matrix mainly composed of proteoglycan and hyaluronan. The collagen fibres are arranged in layers, with different directions of alignment in each layer, giving rise to interesting mechanical properties of pericardium, including the ability to undergo large deformation during performance of regular physiological functions. The present study aims to investigate the effect of penetrating photon ionising radiation on bovine pericardium tissue, being part of a study of the effect of cardiac doses received in breast radiotherapy and the possibility that this can give rise to cardiovascular complications. Irradiation doses in the range 5-80 Gy were used. To characterise the various mechanical properties [elastic modulus, stress relaxation, ultimate tensile strength (UTS) and fracture] a uniaxial tensile test method was applied. The preliminary results reflect the wide inter-sample variations that are expected in dealing with tissues, with only a weak indication of increase in the UTS of the pericardium tissue with increase in radiation dose. Such an effect has also been observed by others, with reduction in UTS at doses of 80 Gy.

  16. 3-D model for cosmic ray planetary ionisation in the middle atmosphere

    Directory of Open Access Journals (Sweden)

    P. I. Y. Velinov

    2005-11-01

    Full Text Available A 3-D planetary model of the cosmic ray electron production rate q(h (cm-3 s-1 has been developed for the strato-mesosphere and lower thermosphere (altitude range 30-100 km with a 10-km step. The spectrum of the primary cosmic rays is modelled by an analytical expression using input data from the CREME96 model. An isotropic penetration of the cosmic rays from the upper hemisphere is assumed in the model and a spherical shape of the Earth's atmosphere is taken into account. The longitudinal effect of ionisation from cosmic rays in the mesosphere and lower thermosphere is calculated. A graphical presentation of the computational results is given for 50 and 90 km at 0°, 40°, 50° and 70° N, S latitudes and all longitudes with a step of 30°. The results of this paper provide a basis for a quantitative understanding of the energetic processes of the middle atmosphere and mechanisms affecting the thermodynamical balance of the Earth's atmosphere.

  17. Monte Carlo configuration interaction applied to multipole moments, ionisation energies and electron affinities

    CERN Document Server

    Coe, J P; Paterson, M J

    2013-01-01

    The method of Monte Carlo configuration interaction (MCCI) [1,2] is applied to the calculation of multipole moments. We look at the ground and excited state dipole moments in carbon monoxide. We then consider the dipole of NO, the quadrupole of the nitrogen molecule and of BH. An octupole of methane is also calculated. We consider experimental geometries and also stretched bonds. We show that these non-variational quantities may be found to relatively good accuracy when compared with FCI results, yet using only a small fraction of the full configuration interaction space. MCCI results in the aug-cc-pVDZ basis are seen to generally have reasonably good agreement with experiment. We also investigate the performance of MCCI when applied to ionisation energies and electron affinities of atoms in an aug-cc-pVQZ basis. We compare the MCCI results with full configuration-interaction quantum Monte Carlo [3,4] and `exact' non-relativistic results [3,4]. We show that MCCI could be a useful alternative for the calculati...

  18. Performance characteristics of a Bioassay method for plutonium using thermal ionisation mass spectrometry (TIMS)

    Energy Technology Data Exchange (ETDEWEB)

    Linauskas, S.H.; Elliot, N.L.; Paterson, L.M.; Totland, M.M

    2003-01-01

    Plutonium-in-urine analysis by radiochemical isolation of Pu followed by thermal ionisation mass spectrometry (TIMS) is capable of high sensitivity and precision measurements {sup 239}Pu and {sup 240}Pu. Bias and precision estimates for the TIMS bioassay program at Chalk River Laboratories easily met the ANSI N13.30 performance criteria standards with {sup 239}Pu results of 1.5% and 3.0%, respectively. Analytical blanks derived from water, artificial urine and true urine samples did not produce any statistically different results. During a four-year period of development and implementation of {sup 239}Pu measurements by TIMS, average sample blank values were reduced from 3.9 fg (9.0 {mu}Bq) to 0.57 fg (1.3 {mu}Bq). This reduction was achieved through rigorous application of clean-room handling techniques throughout sample processing. Blank data were found to follow a Iognormal distribution, and current detection limit parameters for L{sub c} and L{sub d} at the 95% significance levels are 0.85 fg {sup 239}Pu (2.0 {mu}Bq) and 1.3 fg {sup 239}Pu (3.0 {mu}Bq), respectively. Detection limits in this range are expected to be sufficient to identify intakes of Pu/Am mixtures at levels that are around one-twentieth of an ALl or better under routine monitoring situations for ICRP Type S and Type M inhalation solubility classes. (author)

  19. Increased activity of ionised calcium in gall bladder bile in gall stone disease.

    Science.gov (United States)

    Rudnicki, M; Jørgensen, T; Thode, J

    1992-10-01

    The actual activity of ionised calcium (Ca2+) in gall bladder bile determined with an ion-selective electrode was significantly higher in patients with gall stone disease (n = 15) than in patients without gall stones (n = 10) (0.43 mmol/kg v 0.31 mmol/kg; p titration with HCl/NaOH, however, the Ca2+ activity fell with increasing pH in a biphasic manner, with the breaking point occurring at a significantly lower median pH in patients with gall stones than in patients without (pH 7.1 v 8.2; p < 0.0001). The combination of a higher activity of calcium in bile and precipitation of bile salts taking place at a lower pH in patients with gall stone disease than in patients without gall stones suggests a major role for calcium and pH in the pathogenesis of gall stones. Strict anaerobic sampling is not necessary for the measurements of Ca2+ in gall bladder bile, because the Ca2+ was not significantly affected by the changes in pCO2. The metabolic studies suggest, however, that simultaneous measurements of the activity of Ca2+ and pH is important in order to interpret data for the calcium activity in gall bladder bile.

  20. On the divergences in assessment of environmental impacts from ionising radiation following the Fukushima accident.

    Science.gov (United States)

    Strand, P; Sundell-Bergman, S; Brown, J E; Dowdall, M

    2017-01-21

    The accident at the Fukushima-Daiichi Nuclear Power Station on March 11, 2011, led to significant contamination of the surrounding terrestrial and marine environments. Whilst impacts on human health remain the primary concern in the aftermath of such an accident, recent years have seen a significant body of work conducted on the assessment of the accident's impacts on both the terrestrial and marine environment. Such assessments have been undertaken at various levels of biological organisation, for different species, using different methodologies and coming, in many cases, to divergent conclusions as to the effects of the accident on the environment. This article provides an overview of the work conducted in relation to the environmental impacts of the Fukushima accident, critically comparing and contrasting methodologies and results with a view towards finding reasons for discrepancies, should they indeed exist. Based on the outcomes of studies conducted to date, it would appear that in order to avoid the fractured and disparate conclusions drawn in the aftermath of previous accidents, radioactive contaminants and their effects can no longer simply be viewed in isolation with respect to the ecosystems these effects may impact. A combination of laboratory based and field studies with a focus on ecosystem functioning and effects could offer the best opportunities for coherence in the interpretation of the results of studies into the environmental impacts of ionising radiation.

  1. Genomic instability in rat: Breakpoints induced by ionising radiation and interstitial telomeric-like sequences

    Energy Technology Data Exchange (ETDEWEB)

    Camats, Nuria [Institut de Biotecnologia i Biomedicina (IBB), Universitat Autonoma de Barcelona, 08193 Barcelona (Spain); Departament de Biologia Cel.lular, Fisiologia i Immunologia Universitat Autonoma de Barcelona, 08193 Barcelona (Spain); Ruiz-Herrera, Aurora [Departament de Biologia Cel.lular, Fisiologia i Immunologia Universitat Autonoma de Barcelona, 08193 Barcelona (Spain); Parrilla, Juan Jose [Servicio de Ginecologia y Obstetricia, Hospital Universitario Virgen de la Arrixaca, Ctra, Madrid-Cartagena, s/n, El Palmar, 30120 Murcia (Spain); Acien, Maribel [Servicio de Ginecologia y Obstetricia, Hospital Universitario Virgen de la Arrixaca, Ctra, Madrid-Cartagena, s/n, El Palmar, 30120 Murcia (Spain); Paya, Pilar [Servicio de Ginecologia y Obstetricia, Hospital Universitario Virgen de la Arrixaca, Ctra, Madrid-Cartagena, s/n, El Palmar, 30120 Murcia (Spain); Giulotto, Elena [Dipartimento di Genetica e Microbiologia Adriano Buzzati Traverso, Universita degli Studi di Pavia, 27100 Pavia (Italy); Egozcue, Josep [Departament de Biologia Cel.lular, Fisiologia i Immunologia Universitat Autonoma de Barcelona, 08193 Barcelona (Spain); Garcia, Francisca [Institut de Biotecnologia i Biomedicina (IBB), Universitat Autonoma de Barcelona, 08193 Barcelona (Spain); Garcia, Montserrat [Institut de Biotecnologia i Biomedicina (IBB), Universitat Autonoma de Barcelona, 08193 Barcelona (Spain) and Departament de Biologia Cellular, Fisiologia i Immunologia Universitat Autonoma de Barcelona, 08193 Barcelona (Spain)]. E-mail: Montserrat.Garcia.Caldes@uab.es

    2006-03-20

    The Norwegian rat (Rattus norvegicus) is the most widely studied experimental species in biomedical research although little is known about its chromosomal structure. The characterisation of possible unstable regions of the karyotype of this species would contribute to the better understanding of its genomic architecture. The cytogenetic effects of ionising radiation have been widely used for the study of genomic instability, and the importance of interstitial telomeric-like sequences (ITSs) in instability of the genome has also been reported in previous studies in vertebrates. In order to describe the unstable chromosomal regions of R. norvegicus, the distribution of breakpoints induced by X-irradiation and ITSs in its karyotype were analysed in this work. For the X-irradiation analysis, 52 foetuses (from 14 irradiated rats) were studied, 4803 metaphases were analysed, and a total of 456 breakpoints induced by X-rays were detected, located in 114 chromosomal bands, with 25 of them significantly affected by X-irradiation (hot spots). For the analysis of ITSs, three foetuses (from three rats) were studied, 305 metaphases were analysed and 121 ITSs were detected, widely distributed in the karyotype of this species. Seventy-six percent of all hot spots analysed in this study were co-localised with ITSs.

  2. Cancer mortality risk of nuclear power workers due to the exposure of ionising radiation in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Fehringer, F.; Seitz, G. [Berufsgenossenschaft der Feinmechanik und Elektrotechnik, Koln (Germany); Hammer, G.P.; Blettner, M. [Johannes Gutenberg-Universitat Mainz, Institut fur Medizinische Biometrie, Epidemiologie und Informatik des Klinikums (Germany)

    2006-07-01

    A cohort study of German nuclear power workers was set up to investigate overall and cancer mortality risk related to a chronic exposure to ionising radiation of low-level dose. The German study was performed as a part of an international study carried out by the International Agency for Research on Cancer (IARC), Lyon. First results of the international study have been published recently [1]. German data are not yet included in this analysis. The German cohort consists of 4844 employees from 10 nuclear power plants. All persons who worked in these nuclear power plants in 1991 or started employment between 1991 und 1997 are included (except for employees of one plant, whose observation period started in 1992). These persons accumulated about 31,000 person years. Overall, 68 deaths were observed in the observation period between 1.1.1991-31.12.1997. Standardized mortality ratios (SMR) were computed for all causes of death, all cancers, cardiovascular diseases, external causes, and all other causes. Overall, a strong healthy worker effect was observed (SMR=0.52 [95% CI: 0.41;0.67]). No increase in total cancer mortality was seen (SMR=0.85 [95% CI: 0.53;1.30]). However, numbers are too small for stable risk estimates and further effort is under way to complete the cohort in terms of power plants and to extend the follow-up until 2005. (authors)

  3. Boron Arsenide and Boron Phosphide for High Temperature and Luminescent Devices. [semiconductor devices - crystal growth/crystal structure

    Science.gov (United States)

    Chu, T. L.

    1975-01-01

    The crystal growth of boron arsenide and boron phosphide in the form of bulk crystals and epitaxial layers on suitable substrates is discussed. The physical, chemical, and electrical properties of the crystals and epitaxial layers are examined. Bulk crystals of boron arsenide were prepared by the chemical transport technique, and their carrier concentration and Hall mobility were measured. The growth of boron arsenide crystals from high temperature solutions was attempted without success. Bulk crystals of boron phosphide were also prepared by chemical transport and solution growth techniques. Techniques required for the fabrication of boron phosphide devices such as junction shaping, diffusion, and contact formation were investigated. Alloying techniques were developed for the formation of low-resistance ohmic contacts to boron phosphide. Four types of boron phosphide devices were fabricated: (1) metal-insulator-boron phosphide structures, (2) Schottky barriers; (3) boron phosphide-silicon carbide heterojunctions; and (4) p-n homojunctions. Easily visible red electroluminescence was observed from both epitaxial and solution grown p-n junctions.

  4. Van Hove singularities of some icosahedral boron-rich solids by differential reflectivity spectra

    Science.gov (United States)

    Werheit, Helmut

    2015-09-01

    Differential reflectivity spectra of some icosahedral boron rich solids, β-rhombohedral boron, boron carbide and YB66-type crystals, were measured. The derivatives yield the van Hove singularities, which are compared with results obtained by other experimental methods.

  5. Pilot in vivo toxicological investigation of boron nitride nanotubes

    Directory of Open Access Journals (Sweden)

    Ciofani G

    2012-01-01

    Full Text Available Gianni Ciofani1, Serena Danti2, Giada Graziana Genchi1,3, Delfo D'Alessandro2, Jean-Luc Pellequer4, Michaël Odorico4, Virgilio Mattoli1, Mario Giorgi51Italian Institute of Technology, Center of MicroBioRobotics co Scuola Superiore Sant'Anna, 2Department of Neuroscience, University of Pisa, 3The BioRobotics Institute, Scuola Superiore Sant'Anna, Pisa, Italy; 4Commissariat à l'Energie Atomique, Institut de Biologie Environnementale et Biotechnologie, Department of Biochemistry and Nuclear Toxicology, Bagnols-sur-Cèze, France; 5Division of Pharmacology and Toxicology, Veterinary Clinics Department, University of Pisa, Pisa, ItalyAbstract: Boron nitride nanotubes (BNNTs have attracted huge attention in many different research fields thanks to their outstanding chemical and physical properties. During recent years, our group has pioneered the use of BNNTs for biomedical applications, first of all assessing their in vitro cytocompatibility on many different cell lines. At this point, in vivo investigations are necessary before proceeding toward realistic developments of the proposed applications. In this communication, we report a pilot toxicological study of BNNTs in rabbits. Animals were injected with a 1 mg/kg BNNT solution and blood tests were performed up to 72 hours after injection. The analyses aimed at evaluating any acute alteration of hematic parameters that could represent evidence of functional impairment in blood, liver, and kidneys. Even if preliminary, the data are highly promising, as they showed no adverse effects on all the evaluated parameters, and therefore suggest the possibility of the realistic application of BNNTs in the biomedical field.Keywords: boron nitride nanotubes, in vivo testing, toxicology

  6. 11B nuclear magnetic resonance in boron-doped diamond

    Directory of Open Access Journals (Sweden)

    Miwa Murakami, Tadashi Shimizu, Masataka Tansho and Yoshihiko Takano

    2008-01-01

    Full Text Available This review summarizes recent results obtained by 11B solid-state nuclear magnetic resonance (NMR on boron-doped diamond, grown by the high-pressure high-temperature (HPHT or chemical vapor deposition techniques. Simple single-pulse experiments as well as advanced two-dimensional NMR experiments were applied to the boron sites in diamond. It is shown that magic-angle spinning at magnetic fields above 10 T is suitable for observation of high-resolution 11B spectra of boron-doped diamond. For boron-doped HPHT diamonds, the existence of the excess boron that does not contribute to electrical conductivity was confirmed and its 11B NMR signal was characterized. The point-defect structures (B+H complexes and -B-B-/-B-C-B- clusters, postulated previously for the excess boron, were discarded and graphite-like structures were assigned instead.

  7. Synthesis of borophenes: Anisotropic, two-dimensional boron polymorphs

    Science.gov (United States)

    Mannix, Andrew J.; Zhou, Xiang-Feng; Kiraly, Brian; Wood, Joshua D.; Alducin, Diego; Myers, Benjamin D.; Liu, Xiaolong; Fisher, Brandon L.; Santiago, Ulises; Guest, Jeffrey R.; Yacaman, Miguel Jose; Ponce, Arturo; Oganov, Artem R.; Hersam, Mark C.; Guisinger, Nathan P.

    2016-01-01

    At the atomic-cluster scale, pure boron is markedly similar to carbon, forming simple planar molecules and cage-like fullerenes.Theoretical studies predict that two-dimensional (2D) boron sheets will adopt an atomic configuration similar to that of boron atomic clusters. We synthesized atomically thin, crystalline 2D boron sheets (i.e., borophene) on silver surfaces under ultrahigh-vacuum conditions. Atomic-scale characterization, supported by theoretical calculations, revealed structures reminiscent of fused boron clusters with multiple scales of anisotropic, out-of-plane buckling. Unlike bulk boron allotropes, borophene shows metallic characteristics that are consistent with predictions of a highly anisotropic, 2D metal. PMID:26680195

  8. Boron Rich Solids Sensors, Ultra High Temperature Ceramics, Thermoelectrics, Armor

    CERN Document Server

    Orlovskaya, Nina

    2011-01-01

    The objective of this book is to discuss the current status of research and development of boron-rich solids as sensors, ultra-high temperature ceramics, thermoelectrics, and armor. Novel biological and chemical sensors made of stiff and light-weight boron-rich solids are very exciting and efficient for applications in medical diagnoses, environmental surveillance and the detection of pathogen and biological/chemical terrorism agents. Ultra-high temperature ceramic composites exhibit excellent oxidation and corrosion resistance for hypersonic vehicle applications. Boron-rich solids are also promising candidates for high-temperature thermoelectric conversion. Armor is another very important application of boron-rich solids, since most of them exhibit very high hardness, which makes them perfect candidates with high resistance to ballistic impact. The following topical areas are presented: •boron-rich solids: science and technology; •synthesis and sintering strategies of boron rich solids; •microcantileve...

  9. Application of Cycloaddition Reactions to the Syntheses of Novel Boron Compounds

    OpenAIRE

    Maguire, John A.; Hosmane, Narayan S; Yinghuai Zhu; Xiao Siwei

    2010-01-01

    This review covers the application of cycloaddition reactions in forming the boron-containing compounds such as symmetric star-shaped boron-enriched dendritic molecules, nano-structured boron materials and aromatic boronic esters. The resulting boron compounds are potentially important reagents for both materials science and medical applications such as in boron neutron capture therapy (BNCT) in cancer treatment and as drug delivery agents and synthetic intermediates for carbon-carbon cross-c...

  10. Potential of using boric acid as a boron drug for boron neutron capture therapy for osteosarcoma

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, C.F.; Lin, S.Y. [Institute of Nuclear Engineering and Science, National Tsing Hua University, Taiwan (China); Peir, J.J. [Nuclear Science and Technology Development Center, National Tsing Hua University, Taiwan (China); Liao, J.W. [Graduate Institute of Veterinary Pathobiology, National Chung Hsing University, Taiwan (China); Lin, Y.C. [Department of Veterinary Medicine, National Chung Hsing University, Taiwan (China); Chou, F.I., E-mail: fichou@mx.nthu.edu.tw [Institute of Nuclear Engineering and Science, National Tsing Hua University, Taiwan (China)] [Nuclear Science and Technology Development Center, National Tsing Hua University, Taiwan (China)

    2011-12-15

    Osteosarcoma is a malignant tumor commonly found in human and animals. The ability of boric acid (BA) to accumulate in osteosarcoma due to the mechanism of the bone formation of cancer cells would make boron neutron capture therapy (BNCT) an alternative therapy for osteosarcoma. This study evaluated the feasibility of using BA as the boron drug for BNCT of bone cancer. The cytotoxicity of BA to L929 cells exceeded that of UMR-106 cells. With 25 {mu}g {sup 10}B/mL medium of BA treatment, the boron concentration in UMR-106 cells was higher than that in L929 cells. The biodistribution and pharmacokinetics of BA in Sprague-Dawley (SD) rats were studied by administrating 25 mg {sup 10}B/kg body weight to SD rats. Blood boron level decreased rapidly within one hour after BA injection. Boron concentration in the long bone was 4-6 time higher than that of blood. Results of this study suggest that BA may be a potential drug for BNCT for osteosarcoma.

  11. Successive Boronizing and Austempering for GGG-40 Grade Ductile Iron

    Institute of Scientific and Technical Information of China (English)

    Murat Baydogan; Seckin Izzet Akray

    2009-01-01

    Boronizing and austempering were successively applied to a GGG-40 grade ductile iron in order to combine the advantages of both process in a single treatment. This new procedure formed a 30 μm thick boride layer on the surface with subsurface matrix structure consisted of acicular ferrite and retained austenite. Reciprocating wear tests showed that successive boronizing and austempering exhibited considerably higher wear resistance than conventional boronizing having a subsurface matrix structure consisting of ferrite and pearlite.

  12. Measurement of boron isotopes by negative thermal ionization mass spectrometry

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The isobaric interference for boron isotopic measurement by negative thermal ionization mass spectrometry (NTIMS) has been studied. The result shows that the CNO- is not only from the organic material, but also from nitrate in loading reagent in NTIMS. Monitoring the mass 43 ion intensity and 43/42 ratio of blank are also necessary for the boron isotopic measurement by NTIMS, other than is only boron content.

  13. Apparatus for the production of boron nitride nanotubes

    Science.gov (United States)

    Smith, Michael W; Jordan, Kevin

    2014-06-17

    An apparatus for the large scale production of boron nitride nanotubes comprising; a pressure chamber containing; a continuously fed boron containing target; a source of thermal energy preferably a focused laser beam; a cooled condenser; a source of pressurized nitrogen gas; and a mechanism for extracting boron nitride nanotubes that are condensed on or in the area of the cooled condenser from the pressure chamber.

  14. Isotopic effects on the phonon modes in boron carbide.

    Science.gov (United States)

    Werheit, H; Kuhlmann, U; Rotter, H W; Shalamberidze, S O

    2010-10-01

    The effect of isotopes ((10)B-(11)B; (12)C-(13)C) on the infrared- and Raman-active phonons of boron carbide has been investigated. For B isotopes, the contributions of the virtual crystal approximation, polarization vector and isotopical disorder are separated. Boron and carbon isotope effects are largely opposite to one another and indicate the share of the particular atoms in the atomic assemblies vibrating in specific phonon modes. Some infrared-active phonons behave as expected for monatomic boron crystals.

  15. Synthesis of an orthorhombic high pressure boron phase

    Science.gov (United States)

    Zarechnaya, Evgeniya Yu; Dubrovinsky, Leonid; Dubrovinskaia, Natalia; Miyajima, Nobuyoshi; Filinchuk, Yaroslav; Chernyshov, Dmitry; Dmitriev, Vladimir

    2008-12-01

    The densest boron phase (2.52 g cm-3) was produced as a result of the synthesis under pressures above 9 GPa and temperatures up to ~1800 °C. The x-ray powder diffraction pattern and the Raman spectra of the new material do not correspond to those of any known boron phases. A new high-pressure high-temperature boron phase was defined to have an orthorhombic symmetry (Pnnm (No. 58)) and 28 atoms per unit cell.

  16. A Solid-State 11B NMR and Computational Study of Boron Electric Field Gradient and Chemical Shift Tensors in Boronic Acids and Boronic Esters

    Science.gov (United States)

    2010-01-01

    The results of a solid-state 11B NMR study of a series of 10 boronic acids and boronic esters with aromatic substituents are reported. Boron-11 electric field gradient (EFG) and chemical shift (CS) tensors obtained from analyses of spectra acquired in magnetic fields of 9.4 and 21.1 T are demonstrated to be useful for gaining insight into the molecular and electronic structure about the boron nucleus. Data collected at 21.1 T clearly show the effects of chemical shift anisotropy (CSA), with tensor spans (Ω) on the order of 10−40 ppm. Signal enhancements of up to 2.95 were achieved with a DFS-modified QCPMG pulse sequence. To understand the relationship between the measured tensors and the local structure better, calculations of the 11B EFG and magnetic shielding tensors for these compounds were conducted. The best agreement was found between experimental results and those obtained from GGA revPBE DFT calculations. A positive correlation was found between Ω and the dihedral angle (ϕCCBO), which describes the orientation of the boronic acid/ester functional group relative to an aromatic system bound to boron. The small boron CSA is discussed in terms of paramagnetic shielding contributions as well as diamagnetic shielding contributions. Although there is a region of overlap, both Ω and the 11B quadrupolar coupling constants tend to be larger for boronic acids than for the esters. We conclude that the span is generally the most characteristic boron NMR parameter of the molecular and electronic environment for boronic acids and esters, and show that the values result from a delicate interplay of several competing factors, including hydrogen bonding, the value of ϕCCBO, and the electron-donating or withdrawing substituents bound to the aromatic ring. PMID:20337440

  17. Characterization of boron doped nanocrystalline diamonds

    Energy Technology Data Exchange (ETDEWEB)

    Peterlevitz, A C; Manne, G M; Sampaio, M A; Quispe, J C R; Pasquetto, M P; Iannini, R F; Ceragioli, H J; Baranauskas, V [Faculdade de Engenharia Eletrica e Computacao, Departamento de Semicondutores, Instrumentos e Fotonica, Universidade Estadual de Campinas, UNICAMP, Av. Albert Einstein N.400, 13083-852 Campinas SP Brasil (Brazil)], E-mail: vitor.baranauskas@gmail.com

    2008-03-15

    Nanostructured diamond doped with boron was prepared using a hot-filament assisted chemical vapour deposition system fed with an ethyl alcohol, hydrogen and argon mixture. The reduction of the diamond grains to the nanoscale was produced by secondary nucleation and defects induced by argon and boron atoms via surface reactions during chemical vapour deposition. Raman measurements show that the samples are nanodiamonds embedded in a matrix of graphite and disordered carbon grains, while morphological investigations using field electron scanning microscopy show that the size of the grains ranges from 20 to 100 nm. The lowest threshold fields achieved were in the 1.6 to 2.4 V/{mu}m range.

  18. Boron Nitride Nanotube: Synthesis and Applications

    Science.gov (United States)

    Tiano, Amanda L.; Park, Cheol; Lee, Joseph W.; Luong, Hoa H.; Gibbons, Luke J.; Chu, Sang-Hyon; Applin, Samantha I.; Gnoffo, Peter; Lowther, Sharon; Kim, Hyun Jung; Danehy, Paul M.; Inman, Jennifer A.; Jones, Stephen B.; Kang, Jin Ho; Sauti, Godfrey; Thibeault, Sheila A.; Yamakov, Vesselin; Wise, Kristopher E.; Su, Ji; Fay, Catharine C.

    2014-01-01

    Scientists have predicted that carbon's immediate neighbors on the periodic chart, boron and nitrogen, may also form perfect nanotubes, since the advent of carbon nanotubes (CNTs) in 1991. First proposed then synthesized by researchers at UC Berkeley in the mid 1990's, the boron nitride nanotube (BNNT) has proven very difficult to make until now. Herein we provide an update on a catalyst-free method for synthesizing highly crystalline, small diameter BNNTs with a high aspect ratio using a high power laser under a high pressure and high temperature environment first discovered jointly by NASA/NIA JSA. Progress in purification methods, dispersion studies, BNNT mat and composite formation, and modeling and diagnostics will also be presented. The white BNNTs offer extraordinary properties including neutron radiation shielding, piezoelectricity, thermal oxidative stability (> 800 C in air), mechanical strength, and toughness. The characteristics of the novel BNNTs and BNNT polymer composites and their potential applications are discussed.

  19. Behavior of disordered boron carbide under stress.

    Science.gov (United States)

    Fanchini, Giovanni; McCauley, James W; Chhowalla, Manish

    2006-07-21

    Gibbs free-energy calculations based on density functional theory have been used to determine the possible source of failure of boron carbide just above the Hugoniot elastic limit (HEL). A range of B4C polytypes is found to be stable at room pressure. The energetic barrier for shock amorphization of boron carbide is by far the lowest for the B12(CCC) polytype, requiring only 6 GPa approximately = P(HEL) for collapse under hydrostatic conditions. The results clearly demonstrate that the collapse of the B12(CCC) phase leads to segregation of B12 and amorphous carbon in the form of 2-3 nm bands along the (113) lattice direction, in excellent agreement with recent transmission electron microscopy results.

  20. Microadditions of boron and vanadium in ADI

    Directory of Open Access Journals (Sweden)

    Rzychoń T.

    2007-01-01

    Full Text Available In the second part of the study, describing the role of vanadium and boron microadditions in the process of structure formation in heavy-walled castings made from ADI, the results of own investigations were presented. Within this study two series of melts of the ductile iron were made, introducing microadditions of the above mentioned elements to both unalloyed ductile iron and the ductile iron containing high levels of nickel and copper (the composition typical of ADI. Melts were conducted with iron-nickel-magnesium master alloy. Thermal analysis of the solidification process of the cast keel blocks was conducted, the heat treatment of the alloys was carried out, and then the effect of the introduced additions of boron and vanadium on the hardenability of the investigated cast iron was examined and evaluated.

  1. Facile Synthesis of Ternary Boron Carbonitride Nanotubes

    Directory of Open Access Journals (Sweden)

    Luo Lijie

    2009-01-01

    Full Text Available Abstract In this study, a novel and facile approach for the synthesis of ternary boron carbonitride (B–C–N nanotubes was reported. Growth occurred by heating simple starting materials of boron powder, zinc oxide powder, and ethanol absolute at 1150 °C under a mixture gas flow of nitrogen and hydrogen. As substrate, commercial stainless steel foil with a typical thickness of 0.05 mm played an additional role of catalyst during the growth of nanotubes. The nanotubes were characterized by SEM, TEM, EDX, and EELS. The results indicate that the synthesized B–C–N nanotubes exhibit a bamboo-like morphology and B, C, and N elements are homogeneously distributed in the nanotubes. A catalyzed vapor–liquid–solid (VLS mechanism was proposed for the growth of the nanotubes.

  2. Boron nitride encapsulated graphene infrared emitters

    Energy Technology Data Exchange (ETDEWEB)

    Barnard, H. R.; Zossimova, E.; Mahlmeister, N. H.; Lawton, L. M.; Luxmoore, I. J.; Nash, G. R., E-mail: g.r.nash@exeter.ac.uk [College of Engineering, Mathematics and Physical Sciences, University of Exeter, Exeter EX4 4QF (United Kingdom)

    2016-03-28

    The spatial and spectral characteristics of mid-infrared thermal emission from devices containing a large area multilayer graphene layer, encapsulated using hexagonal boron nitride, have been investigated. The devices were run continuously in air for over 1000 h, with the emission spectrum covering the absorption bands of many important gases. An approximate solution to the heat equation was used to simulate the measured emission profile across the devices yielding an estimated value of the characteristic length, which defines the exponential rise/fall of the temperature profile across the device, of 40 μm. This is much larger than values obtained in smaller exfoliated graphene devices and reflects the device geometry, and the increase in lateral heat conduction within the devices due to the multilayer graphene and boron nitride layers.

  3. Screen printed boron emitters for solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Recart, F.; Freire, I.; Perez, L.; Lago-Aurrekoetxea, R.; Jimeno, J.C.; Bueno, G. [Instituto de Tecnologia Microelectronica, Teknologia Mikroelektronikoaren Institutua UPV/EHU, Alda.Urquijo s/n, 48013 Bilbao (Spain)

    2007-06-15

    Screen printed (SP) boron emitters are presented as a useful option for the manufacturing of p-type emitters of solar cells. Details are provided on the diffusion process, including deposition, drying and firing steps, the latter performed in an infrared belt furnace. Besides their main dependences on the firing conditions, the sheet resistances and dopant profiles of the resulting emitters reveal the relevance of the drying step and the exhaustion limits of the doping source. A characterization of the recombination concludes that moderate emitter saturation currents (J{sub oe}<0.5 pA/cm{sup 2}) and acceptable bulk lifetimes ({tau}{sub B}>40 {mu}s) can be obtained on Czochralski silicon wafers. Finally, Cz n-type 0.7 {omega} cm solar cells are presented, which once again prove the feasibility of SP boron emitters and point to issues regarding their metallization. (author)

  4. Boron removal from molten silicon using sodium-based slags

    Institute of Scientific and Technical Information of China (English)

    Yin Changhao; Hu Bingfeng; Huang Xinming

    2011-01-01

    Slag refining,as an important option for boron removal to produce solar grade silicon (SOG-Si) from metallurgical grade silicon (MG-Si),has attracted increasing attention.In this paper,Na2CO3-SiO2 systems were chosen as the sodium-based refining slag materials for boron removal from molten silicon.Furthermore,the effect of Al2O3 addition for boron removal was studied in detail,which showed that an appropriate amount of Al2O3 can help retention of the basicity of the slags,hence improving the boron removal rate.

  5. Switchable Surface Wettability by Using Boronic Ester Chemistry.

    Science.gov (United States)

    Taleb, Sabri; Noyer, Elisabeth; Godeau, Guilhem; Darmanin, Thierry; Guittard, Frédéric

    2016-01-18

    Here, we report for the first time the use of a boronic ester as an efficient tool for reversible surface post-functionalization. The boronic ester bond allows surfaces to be reversibly switched from hydrophilic to hydrophobic. Based on the well-known boronic acid/glycol affinity, this strategy offers the opportunity to play with surface hydrophobic properties by adding various boronic acids onto substrates bearing glycol groups. The post-functionalization can then be reversed to regenerate the starting glycol surface. This pathway allows for the preparation of various switchable surfaces for a large range of applications in biosensors, liquid transportation, and separation membranes.

  6. Laser Boronizing of Stainless Steel with Direct Diode Laser

    Science.gov (United States)

    Kusuhara, Takayoshi; Morimoto, Junji; Abe, Nobuyuki; Tsukamoto, Masahiro

    Boronizing is a thermo-chemical surface treatment in which boron atoms are diffused into the surface of a work piece to form borides with the base material. When applied to the metallic materials, boronizing provides wear and abrasion resistance comparable to sintered carbides. However conventional boronizing is carried out at temperatures ranging from 800°C to 1050°C and takes from one to several hours. The structure and properties of the base material is influenced considerably by the high temperature and long treatment time. In order to avoid these drawbacks of conventional boronizing, laser-assisted boronizing is investigated which activates the conventional boronizing material and the work piece with a high density laser power. In this study, effect of laser characteristics was examined on the laser boronizing of stainless steel. After laser boronizing, the microstructure of the boride layer was analyzed with an optical microscope, electron probe micro analyser(EPMA) and X-ray diffractometer (XRD). The mechanical properties of borided layer were evaluated using Vickers hardness tester and sand erosion tester. Results showed that the boride layer was composed of NiB, CrB, FeB and Fe2B, and get wear resistance.

  7. Doping Silicon Wafers with Boron by Use of Silicon Paste

    Institute of Scientific and Technical Information of China (English)

    Yu Gao; Shu Zhou; Yunfan Zhang; Chen Dong; Xiaodong Pi; Deren Yang

    2013-01-01

    In this work we introduce recently developed silicon-paste-enabled p-type doping for silicon.Boron-doped silicon nanoparticles are synthesized by a plasma approach.They are then dispersed in solvents to form silicon paste.Silicon paste is screen-printed at the surface of silicon wafers.By annealing,boron atoms in silicon paste diffuse into silicon wafers.Chemical analysis is employed to obtain the concentrations of boron in silicon nanoparticles.The successful doping of silicon wafers with boron is evidenced by secondary ion mass spectroscopy (SIMS) and sheet resistance measurements.

  8. Lateral gas phase diffusion length of boron atoms over Si/B surfaces during CVD of pure boron layers

    Energy Technology Data Exchange (ETDEWEB)

    Mohammadi, V., E-mail: V.Mohammadi@tudelft.nl; Nihtianov, S. [Department of Microelectronics, Delft University of Technology, Mekelweg 4, 2628 CD, Delft (Netherlands)

    2016-02-15

    The lateral gas phase diffusion length of boron atoms, L{sub B}, along silicon and boron surfaces during chemical vapor deposition (CVD) using diborane (B{sub 2}H{sub 6}) is reported. The value of L{sub B} is critical for reliable and uniform boron layer coverage. The presented information was obtained experimentally and confirmed analytically in the boron deposition temperature range from 700 °C down to 400 °C. For this temperature range the local loading effect of the boron deposition is investigated on the micro scale. A L{sub B} = 2.2 mm was determined for boron deposition at 700 °C, while a L{sub B} of less than 1 mm was observed at temperatures lower than 500 °C.

  9. New nanoforms of carbon and boron nitride

    Energy Technology Data Exchange (ETDEWEB)

    Pokropivny, V V [Institute for Problems of Materials Science of National Academy of Sciences of Ukraine (Ukraine); Ivanovskii, A L [Institute of Solid State Chemistry, Urals Branch of the Russian Academy of Sciences, Ekaterinburg (Russian Federation)], e-mail: Ivanovskii@ihim.uran.ru

    2008-10-31

    Data on new carbon nanostructures including those based on fullerenes, nanotubes as well monolithic diamond-like nanoparticles, nanofibres, various nanocomposites, etc., published in the last decade are generalised. The experimental and theoretical data on their atomic and electronic structures, the nature of chemical bonds and physicochemical properties are discussed. These data are compared with the results obtained in studies of nanoforms of boron nitride, an isoelectronic analogue of carbon. Potential fields of applications of the new nanostructures are considered.

  10. New nanoforms of carbon and boron nitride

    Science.gov (United States)

    Pokropivny, V. V.; Ivanovskii, A. L.

    2008-10-01

    Data on new carbon nanostructures including those based on fullerenes, nanotubes as well monolithic diamond-like nanoparticles, nanofibres, various nanocomposites, etc., published in the last decade are generalised. The experimental and theoretical data on their atomic and electronic structures, the nature of chemical bonds and physicochemical properties are discussed. These data are compared with the results obtained in studies of nanoforms of boron nitride, an isoelectronic analogue of carbon. Potential fields of applications of the new nanostructures are considered.

  11. Electron-Spin Resonance in Boron Carbide

    Science.gov (United States)

    Wood, Charles; Venturini, Eugene L.; Azevedo, Larry J.; Emin, David

    1987-01-01

    Samples exhibit Curie-law behavior in temperature range of 2 to 100 K. Technical paper presents studies of electron-spin resonance of samples of hot pressed B9 C, B15 C2, B13 C2, and B4 C. Boron carbide ceramics are refractory solids with high melting temperatures, low thermal conductives, and extreme hardnesses. They show promise as semiconductors at high temperatures and have unusually large figures of merit for use in thermoelectric generators.

  12. Amorphous Carbon-Boron Nitride Nanotube Hybrids

    Science.gov (United States)

    Kim, Jae Woo (Inventor); Siochi, Emilie J. (Inventor); Wise, Kristopher E. (Inventor); Lin, Yi (Inventor); Connell, John (Inventor)

    2016-01-01

    A method for joining or repairing boron nitride nanotubes (BNNTs). In joining BNNTs, the nanotube structure is modified with amorphous carbon deposited by controlled electron beam irradiation to form well bonded hybrid a-C/BNNT structures. In repairing BNNTs, the damaged site of the nanotube structure is modified with amorphous carbon deposited by controlled electron beam irradiation to form well bonded hybrid a-C/BNNT structures at the damage site.

  13. Formation and Structure of Boron Nitride Nanotubes

    Institute of Scientific and Technical Information of China (English)

    Jiang ZHANG; Zongquan LI; Jin XU

    2005-01-01

    Boron nitride (BN) nanotubes were simply synthesized by heating well-mixed boric acid, urea and iron nitrate powders at 1000℃. A small amount of BN nanowires was also obtained in the resultants. The morphological and structural characters of the BN nanostructures were studied using transmission electron microscopy. Other novel BN nanostructures, such as Y-junction nanotubes and bamboo-like nanotubes, were simultaneously observed. The growth mechanism of the BN nanotubes was discussed briefly.

  14. Critical Range of Soil Boron for Prognosis of Boron Deficiency in Oilseed Rape

    Institute of Scientific and Technical Information of China (English)

    WEIYOUZHANG

    2001-01-01

    Relationships between seed yields of oilseed rape(Brassica napus L.) and extractable boron concen-trations in three soil layers(A,P and W) were investigated through ten experiments on three types of soils(Alluvic Entisols,Udic Ferrisols and Sagnic Anthrosols) in northern,Western and middle Zhejing Province.Among several mathematical models used to described the relationships,the polynomial equation,y=a+bx+cx2+dx3,where y is the yield of oilseed rape seed and x the extractable boron concentration in P layer of soil,was the best one.The critical range of the concentrations corresponding to 90% of the maximum oilseed rape yield was 0.40-0.52 mg kg-1,The extractable boron concentration of the P layers of the soils was the most stable,The critical range determined was verified through the production practices of oilseed rape in Zhejiang and Anhui provinces.

  15. Critical Range of Soil Boron for Prognosis of Boron Deficiency in Oilseed Rape

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Relationships between seed yields of oilseed rape (Brassica napus L.) and extractable boron concen- trations in three soil layers (A, P and W) were investigated through ten experiments on three types of soils (Alluvic Entisols, Udic Ferrisols and Stagnic Anthrosols) in northern, western and middle Zhejiang Province. Among several mathematical models used to described the relationships, the polynomial equation, y = a + bx + cx2 + dx3, where y is the yield of oilseed rape seed and x the extractable boron concentration in P layer of soil, was the best one. The critical range of the concentrations corresponding to 90% of the maximum oilseed rape yield was 0.40~0.52 mg kg-1. The extractable boron concentration of the P layers of the soils was the most stable. The critical range determined was verified through the production practices of oilseed rape in Zhejiang and Anhui provinces.

  16. Galaxy emission line classification using 3D line ratio diagrams

    CERN Document Server

    Vogt, Frédéric P A; Kewley, Lisa J; Sutherland, Ralph S; Scharwaechter, Julia; Basurah, Hassan M; Ali, Alaa; Amer, Morsi A

    2014-01-01

    Two-dimensional (2D) line ratio diagnostic diagrams have become a key tool in understanding the excitation mechanisms of galaxies. The curves used to separate the different regions - HII-like or else excited by an active galactic nucleus (AGN) - have been refined over time but the core technique has not evolved significantly. However, the classification of galaxies based on their emission line ratios really is a multi-dimensional problem. Here we exploit recent software developments to explore the potential of three-dimensional (3D) line ratio diagnostic diagrams. We introduce a specific set of 3D diagrams, the ZQE diagrams, which separate the oxygen abundance and the ionisation parameter of HII region-like spectra, and which also enable us to probe the excitation mechanism of the gas. By examining these new 3D spaces interactively, we define a new set of 2D diagnostics, the ZE diagnostics, which can provide the metallicity of objects excited by hot young stars, and which cleanly separate HII region-like obje...

  17. Boron neutron capture therapy. Synthesis of boronated amines- and DNA intercalating agents for potential use in cancer therapy

    Energy Technology Data Exchange (ETDEWEB)

    Ghaneolhosseini, H

    1998-05-01

    Boron Neutron Capture Therapy is a binary cancer treatment modality, involving the delivery of a suitable boron compound to tumour cells followed by irradiation of the tumour by thermal neutrons. Boronated agents can selectively be delivered to tumour cells either directly with tumour-specific boron compounds, or by use of targeting strategies. However, the efficacy of this method would increase if the boron agents are localised in the cell nucleus rather than in the cell cytoplasm when neutron irradiation takes place. With these considerations in mind, some boronated DNA intercalating/interacting agents such as phenanthridine- acridine- spermidine- and naphthalimide derivatives were synthesised. Aminoalkyl-o-carboranes were synthesised in order to be used both for coupling to macromolecules and also for halogenation of their corresponding nido-derivatives. The amino groups were introduced using the Gabriel reagent N, N-dibenzyl iminodicarboxylate to provide 1-(aminomethyl)- and 1-(2-aminoethyl)-o-carboranes. The first attempt to achieve the possibility to accumulate a higher concentration of boron atoms in the cell nucleus was to synthesize carboranyl phenanthridinium analogues by reacting a p- or o-carboranyl moiety with phenanthridine, a chromophore with a planar aromatic ring system as DNA intercalator. Boronated acridine-spermidine, boronated diacridine, and boronated dispermidine were obtained in order to increase water solubility to avoid the interaction of these agents with non-DNA sides of the cell, especially membranes; and to enhance the feasibility of a higher DNA-binding constant and also decrease the DNA-drug dissociation rate. Finally, the synthesis of a boronated naphthalimide derivative was carried out by nucleophilic reaction of a primary aminoalkyl-p-carborane with naphthalic anhydride. Biological evaluations on DNA-binding, toxicity, and cellular binding with carboranyl phenanthridinium analogues, boronated acridine- and spermidine are described

  18. Boron impregnation treatment of Eucalyptus grandis wood.

    Science.gov (United States)

    Dhamodaran, T K; Gnanaharan, R

    2007-08-01

    Eucalyptus grandis is suitable for small timber purposes, but its wood is reported to be non-durable and difficult to treat. Boron compounds being diffusible, and the vacuum-pressure impregnation (VPI) method being more suitable for industrial-scale treatment, the possibility of boron impregnation of partially dry to green timber was investigated using a 6% boric acid equivalent (BAE) solution of boric acid and borax in the ratio 1:1.5 under different treatment schedules. It was found that E. grandis wood, even in green condition, could be pressure treated to desired chemical dry salt retention (DSR) and penetration levels using 6% BAE solution. Up to a thickness of 50mm, in order to achieve a DSR of 5 kg/m(3) boron compounds, the desired DSR level as per the Indian Standard for perishable timbers for indoor use, it was found that neither the moisture content of wood nor the treatment schedule posed any problem as far as the treatability of E. grandis wood was concerned.

  19. Tracing Inflows and Outflows with Absorption Lines in Circumgalactic Gas

    CERN Document Server

    Ford, Amanda Brady; Oppenheimer, Benjamin D; Katz, Neal; Kollmeier, Juna A; Thompson, Robert; Weinberg, David H

    2013-01-01

    We examine how HI and metal absorption lines within low-redshift galaxy halos trace the dynamical state of circumgalactic gas, using cosmological hydrodynamic simulations that include a well-vetted heuristic model for galactic outflows. We categorize inflowing, outflowing, and ambient gas based on its history and fate as tracked in our simulation. Following our earlier work showing that the ionisation level of absorbers was a primary factor in determining the physical conditions of absorbing gas, we show here that it is also a governing factor for its dynamical state. Low-ionisation metal absorbers (e.g. MgII) tend to arise in gas that will fall onto galaxies within several Gyr, while high-ionisation metal absorbers (e.g. OVI) generally trace material that was deposited by outflows many Gyr ago. Inflowing gas is dominated by enriched material that was previously ejected in an outflow, hence accretion at low redshifts is typically substantially enriched. Recycling wind material is preferentially found closer t...

  20. Derivation of hazardous doses for amphibians acutely exposed to ionising radiation.

    Science.gov (United States)

    Fuma, Shoichi; Watanabe, Yoshito; Kawaguchi, Isao; Takata, Toshitaro; Kubota, Yoshihisa; Ban-Nai, Tadaaki; Yoshida, Satoshi

    2012-01-01

    Derivation of effect benchmark values for each taxonomic group, which has been difficult due to lack of experimental effects data, is required for more adequate protection of the environment from ionising radiation. Estimation of effects doses from nuclear DNA mass and subsequent species sensitivity distribution (SSD) analysis were proposed as a method for such a derivation in acute irradiation situations for assumed nuclear accident scenarios. As a case study, 5% hazardous doses (HD₅s), at which only 5% of species are acutely affected at 50% or higher lethality, were estimated on a global scale. After nuclear DNA mass data were obtained from a database, 50% lethal doses (LD₅₀s) for 4.8 and 36% of the global Anura and Caudata species, respectively, were estimated by correlative equations between nuclear DNA mass and LD₅₀s. Differences between estimated and experimental LD₅₀s were within a factor of three. The HD₅s obtained by the SSD analysis of these estimated LD₅₀s data were 5.0 and 3.1 Gy for Anura and Caudata, respectively. This approach was also applied to the derivation of regional HD₅s. The respective HD₅s were 6.5 and 3.2 Gy for Anura and Caudata inhabiting Japan. This HD₅ value for the Japanese Anura was significantly higher than the global value, while Caudata had no significant difference in global and Japanese HD₅s. These results suggest that this approach is also useful for derivation of regional benchmark values, some of which are likely different from the global values.

  1. Resveratrol and its methoxy-derivatives as modulators of DNA damage induced by ionising radiation.

    Science.gov (United States)

    Traversi, Gianandrea; Fiore, Mario; Leone, Stefano; Basso, Emiliano; Di Muzio, Elena; Polticelli, Fabio; Degrassi, Francesca; Cozzi, Renata

    2016-07-01

    Various naturally occurring stilbene-like compounds that are related to resveratrol (RSV) possess some of the beneficial effects of the parent molecule and provide even further benefits. Therefore, a series of methoxylated analogues of RSV were prepared with the aim of increasing antitumour and proapoptotic activity. In a previous article, we studied two methoxy-derivatives, pterostilbene (PTERO) and trimethoxystilbene (TRIMETHOXY), in which the first was formed by the substitution of two hydroxyl groups with two methoxy groups (trans-3,5-dimethoxy-4'-hydroxystilbene) and the second was formed by the replacement of all three OH groups with methoxy groups (trans-3,5,4'-trimethoxystilbene). Both methoxy-derivatives showed stronger antioxidant activity when compared with RSV. In the present article, we focused on the analysis of the ability of RSV and its two methoxylated derivatives to protect proliferating non-tumoural cells from the damage induced by ionising radiation (IR). First we showed that the methoxy derivatives, contrary to their parental compound, are unable to affect topoisomerase enzyme and consequently are not clastogenic per se Second we showed that both PTERO and TRIMETHOXY more efficiently reduce the chromosome damage induced by IR. Furthermore, TRIMETHOXY, but not PTERO, causes a delay in cell proliferation, particularly in mitosis progression increasing the number of cells in metaphase at the expense of prophases and ana/telophases. © The Author 2016. Published by Oxford University Press on behalf of the UK Environmental Mutagen Society. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  2. The electrical charging of inactive aerosols in high ionised atmosphere, the electrical charging of artificial beta radioactive aerosols; Le processus de charge electrique: des aerosols non radioactifs en milieu fortement ionise, des aerosols radioactifs artificiels emetteurs beta

    Energy Technology Data Exchange (ETDEWEB)

    Gensdarmes, F

    2000-07-01

    The electrical properties of aerosols greatly influence their transport and deposition in a containment. In a bipolar ionic atmosphere, a neutral electric charge on aerosols is commonly assumed. However, many studies report a different charge distribution in some situations, like highly ionised atmosphere or in the case of radioactive aerosols. Such situations could arise from a hypothetical accident in a nuclear power plant. Within the framework of safety studies which are carried out at IPSN, our aims were the study of electrical properties of aerosols in highly ionised atmosphere, and the study of artificial radioactive aerosols, in order to suggest experimental validation of available theories. For this purpose, we designed an experimental device that allows us to measure non-radioactive aerosol charge distribution under high gamma irradiation, up to 10{sup 4} Gy/h. With our experimental device we also studied the properties of small ions in the medium. Our results show a variation of the charge distribution in highly ionised atmosphere. The charge increases with the dose of gamma ray. We have related this variation with the one of the small ions in the gases, according to theoretical prediction. However, the model overestimates slightly our experimental results. In the case of the radioactive aerosols, we have designed an original experimental device, which allows us to study the charge distribution of a {sup 137}Cs aerosol. Our results show that the electric charging of such aerosols is strongly dependent on evolution parameters in a containment. So, our results underline a great enhancement of self-charging of particles which are sampled in a confined medium. Our results are qualitatively in agreement with the theoretical model; nevertheless the latter underestimates appreciably the self-charging, owing to the fact that wall effects are not taken into account. (author)

  3. External dosimetry for ionising radiation. From the national standard to the users in radiotherapy and radiation protection; La dosimetrie externe des rayonnements ionisants de la reference nationale aux utilisateurs en radiotherapie et en radioprotection

    Energy Technology Data Exchange (ETDEWEB)

    Bordy, J.M

    2009-07-01

    This report presents a review of the external dosimetry of the ionising radiations for the protection of the human being. Looking at this topic, at first we are confronted with its diversity: the protection of the workers and the public against radiations, the medical exposures for radiotherapy, diagnosis and surgery, and the accidental situations. These aspects are often artificially separated so that the global comprehension becomes more difficult. We underline the points of convergence and the bonds which exist between the concepts of dosimetry adopted to deal with its different aspects. It also appeared useful to avoid proposing a dictionary of definitions copied in the reports of the international commissions, and adopting the formalism of the ICRU reports. This is why the definitions, when they are essential, are put in appendix. This text presents the reasons which led to the adoption of the system of quantity used today for the external dosimetry of the ionising radiations. After an introduction dealing with the general principle, the first chapter deals with the 'physical' quantities and the methods used for the determination of the national references. The second chapter, through the protection against radiation of the workers and the public, describes the bonds between the measurable 'operational' quantities and the non measurable 'protections' quantities which allow establishing the radiation protection limits and check that they are respected. The third chapter deals with the difficulties encountered for the measurements in area and personal dosimetry. The fourth chapter deals with the specificities of the medical exposures with the 'practical' quantities, the principle of optimisation and how radiotherapy is implemented. The fifth chapter briefly describes the case of the concerted exposures and of the accident. In conclusion, we analyse the needs and some potential new avenues of work for the metrology of the

  4. Boron Removal in Radioactive Liquid Waste by Forward Osmosis Membrane

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Dooseong; Choi, Hei Min; Lee, Kune Woo; Moon Jeikwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    These wastes contain about 0.3-0.8 wt% boric acid and have been concentrated through an evaporation treatment. Boric acid tends to crystallize owing to its solubility, and to plug the evaporator. The volume reduction obtained through evaporation is limited by the amount of boric acid in the waste. As an emerging technology, forward osmosis (FO) has attracted growing interest in wastewater treatment and desalination. FO is a membrane process in which water flows across a semi-permeable membrane from a feed solution of lower osmotic pressure to a draw solution of higher osmotic pressure. However, very few studies on the removal of boron by FO have been performed. The objective of this study is to evaluate the possibility of boron separation in radioactive liquid waste by FO. In this study, the performance of FO was investigated to separate boron in the simulated liquid waste under the factors such as pH, osmotic pressure, ionic strength of the solution, and membrane characteristic. The boron separation in radioactive borate liquid waste was investigated with an FO membrane. When the feed solution containing boron is treated by the FO membrane, the boron permeation depends on the type of membrane, membrane orientation, pH of the feed solution, salt and boron concentration in the feed solution, and osmotic pressure of the draw solution. The boron flux begins to decline from pH 7, and increases with an increase in the osmotic driving force. The boron flux of the CTA-ES and ALFD membrane orientation is higher than those of the CTA-NW and ALFF orientation, respectively. The boron permeation rate is constant regardless of the osmotic pressure and membrane orientation. The boron flux decreases slightly with the salt concentration, but it is not heavily influenced at a low salt concentration.

  5. The soft X-ray spectrum of the luminous narrow line Seyfert galaxy PG1211+143

    CERN Document Server

    Pounds, K A

    2013-01-01

    An XMM-Newton observation of the luminous Seyfert galaxy PG1211+143 in 2001 showed the first evidence for a highly ionised high speed wind (in a non-BAL AGN), with a velocity of v~0.1c based on the identification of blue-shifted absorption lines in both EPIC and RGS spectra. An order-of-magnitude lower velocity was subsequently claimed based on an ion-by-ion model fit to the soft X-ray data. Although repeated observations with XMM-Newton, Chandra and Suzaku confirmed a high velocity, all were based on detection of blue-shifted absorption lines of highly ionised Fe. We show here, in a new analysis of the XMM-Newton RGS data, that the high velocity is indeed present in the soft X-ray spectra, with the higher spectral resolution providing evidence for a second, lower ionisation component close to the systemic velocity of PG1211+143. Variability of the more highly ionised absorption component conforms with that found previously in EPIC spectra in excluding a local origin, while broad emission features are identif...

  6. Selective uptake of p-boronophenylalanine by osteosarcoma cells for boron neutron capture therapy

    Energy Technology Data Exchange (ETDEWEB)

    Ferrari, C. [Department of Surgery, Experimental Surgery Laboratory, University of Pavia, Piazza Botta, Pavia (Italy)], E-mail: ferraric@unipv.it; Zonta, C.; Cansolino, L.; Clerici, A.M.; Gaspari, A. [Department of Surgery, Experimental Surgery Laboratory, University of Pavia, Piazza Botta, Pavia (Italy); Altieri, S.; Bortolussi, S.; Stella, S. [Department of Nuclear and Theoretical Physics of University, Via Bassi, 6, Pavia (Italy); National Institute of Nuclear Physics (INFN) Section of Pavia, Via Bassi, 6, Pavia (Italy); Bruschi, P. [Department of Nuclear and Theoretical Physics of University, Via Bassi, 6, Pavia (Italy); Dionigi, P.; Zonta, A. [Department of Surgery, Experimental Surgery Laboratory, University of Pavia, Piazza Botta, Pavia (Italy)

    2009-07-15

    Osteosarcoma is the most common non-hematologic primary cancer type that develops in bone. Current osteosarcoma treatments combine multiagent chemotherapy with extensive surgical resection, which in some cases makes necessary the amputation of the entire limb. Nevertheless its infiltrative growth leads to a high incidence of local and distant recurrences that reduce the percentage of cured patients to less than 60%. These poor data required to set up a new therapeutic approach aimed to restrict the surgical removal meanwhile performing a radical treatment. Boron neutron capture therapy (BNCT), a particular radiotherapy based on the nuclear capture and fission reactions by atoms of {sup 10}B, when irradiated with thermal neutrons, could be a valid alternative or integrative option in case of osteosarcoma management, thanks to its peculiarity in selectively destroying neoplastic cells without damaging normal tissues. Aim of the present work is to investigate the feasibility of employing BNCT to treat the limb osteosarcoma. Boronophenylalanine (BPA) is used to carry {sup 10}B inside the neoplastic cells. As a first step the endocellular BPA uptake is tested in vitro on the UMR-106 osteosarcoma cell line. The results show an adequate accumulation capability. For the in vivo experiments, an animal tumor model is developed in Sprague-Dawley rats by means of an intrafemoral injection of UMR-106 cells at the condyle site. The absolute amounts of boron loading and the tumor to normal tissue {sup 10}B ratio are evaluated 2 h after the i.v. administration of BPA. The boron uptake by the neoplastic tissue is almost twice the normal one. However, higher values of boron concentration in tumor are requested before upholding BNCT as a valid therapeutic option in the treatment of osteosarcoma.

  7. Valence one-electron and shake-up ionisation bands of polycyclic aromatic hydrocarbons. IV. The dibenzanthracene species

    Energy Technology Data Exchange (ETDEWEB)

    Deleuze, Michael S. [Theoretische Chemie, Departement SBG, Universiteit Hasselt, Agoralaan, Gebouw D, B-3590 Diepenbeek (Belgium)], E-mail: michael.deleuze@uhasselt.be

    2006-10-26

    A comprehensive study of the He (I) ultra-violet photoelectron spectra of the 1.2,3.4; 1.2,5.6 and 1.2,7.8 isomers of dibenzanthracene up to the double ionisation threshold at {approx}18 eV is presented with the aid of one-particle Green's Function calculations performed using the outer-valence Green's Function (OVGF) approach and the third-order algebraic diagrammatic construction [ADC(3)] scheme, along with basis sets of improving quality. Suited extrapolations of the ADC(3) results for the one-electron energies characterising the {pi}-band system ({epsilon} {sub b} < 10 eV) to Dunning's correlation consistent basis set of triple zeta quality (cc-pVTZ) enable theoretical insights into HeI measurements which approach chemical accuracy (1 kcal/mol or 43.4 meV). In contrast, a confrontation of simulated spectral envelopes with high-resolution He I photoelectron spectra indicates that polycyclic aromatic molecules with sterically overcrowded bay regions are more susceptible to undergo vibronic coupling complications at the {sigma}-ionisation onset. OVGF/cc-pVDZ or OVGF/cc-pVTZ pole strengths smaller than 0.85 systematically corroborate a breakdown of the orbital (or one-electron) picture of ionisation at the ADC(3)/6-31G levels. The extent of shake-up bands is correspondingly related to topological, structural and magnetic criteria of aromaticity. Comparison is made with calculations of the lowest doublet-doublet excitation energies of the related radical cations, by means of time-dependent density functional theory (TDDFT)

  8. Lightning-driven inner radiation belt energy deposition into the atmosphere: implications for ionisation-levels and neutral chemistry

    Directory of Open Access Journals (Sweden)

    C. J. Rodger

    2007-08-01

    Full Text Available Lightning-generated whistlers lead to coupling between the troposphere, the Van Allen radiation belts and the lower-ionosphere through Whistler-induced electron precipitation (WEP. Lightning produced whistlers interact with cyclotron resonant radiation belt electrons, leading to pitch-angle scattering into the bounce loss cone and precipitation into the atmosphere. Here we consider the relative significance of WEP to the lower ionosphere and atmosphere by contrasting WEP produced ionisation rate changes with those from Galactic Cosmic Radiation (GCR and solar photoionisation. During the day, WEP is never a significant source of ionisation in the lower ionosphere for any location or altitude. At nighttime, GCR is more significant than WEP at altitudes <68 km for all locations, above which WEP starts to dominate in North America and Central Europe. Between 75 and 80 km altitude WEP becomes more significant than GCR for the majority of spatial locations at which WEP deposits energy. The size of the regions in which WEP is the most important nighttime ionisation source peaks at ~80 km, depending on the relative contributions of WEP and nighttime solar Lyman-α. We also used the Sodankylä Ion Chemistry (SIC model to consider the atmospheric consequences of WEP, focusing on a case-study period. Previous studies have also shown that energetic particle precipitation can lead to large-scale changes in the chemical makeup of the neutral atmosphere by enhancing minor chemical species that play a key role in the ozone balance of the middle atmosphere. However, SIC modelling indicates that the neutral atmospheric changes driven by WEP are insignificant due to the short timescale of the WEP bursts. Overall we find that WEP is a significant energy input into some parts of the lower ionosphere, depending on the latitude/longitude and altitude, but does not play a significant role in the neutral chemistry of the mesosphere.

  9. Event-based versus process-based informed consent to address scientific evidence and uncertainties in ionising medical imaging.

    Science.gov (United States)

    Recchia, Virginia; Dodaro, Antonio; Braga, Larissa

    2013-10-01

    Inappropriate ionising medical imaging has been escalating in the last decades. This trend leads to potential damage to health and has been associated to bioethical and legal issues of patient autonomy. While the doctrine underlines the importance of using informed consent to improve patient autonomy and physician-patient communication, some researchers have argued that it often falls short of this aim. There are basically two different informed consent practices. The first - the so-called "event-based model" - regards informed consent as a passive signature of a standard unreadable template, performed only once in each medical pathway. The second - the so-called "process-based model" - integrates information into the continuing dialogue between physician and patient, vital for diagnosis and treatment. Current medical behaviour often embraces the event-based model, which is considered ineffective and contributes to inappropriateness. We sought, in this review, to analyse from juridical and communication standpoints whether process-based informed consent can deal with scientific uncertainties in radiological decision-making. The informed consent is still a distinctive process in defence of both patients' and physicians' health and dignity in rule-of-law states and consequently in curtailing the abuse of ionising medical radiation. • Inappropriate ionising medical imaging is widespread and increasing worldwide. • This trend leads to noteworthy damage to health and is linked to the issue of patient autonomy. • Some authors have argued that informed consent often falls short of improving patient autonomy. • Process-based informed consent can deal with scientific uncertainties to contrast inappropriateness. • Informed consent is still a distinctive process in defence of both patients and physicians.

  10. Phase diagrams and synthesis of cubic boron nitride

    CERN Document Server

    Turkevich, V Z

    2002-01-01

    On the basis of phase equilibria, the lowest temperatures, T sub m sub i sub n , above which at high pressures cubic boron nitride crystallization from melt solution is allowable in terms of thermodynamics have been found for a number of systems that include boron nitride.

  11. Contamination of urban garden soils with copper and boron

    Energy Technology Data Exchange (ETDEWEB)

    Purves, D.

    1966-06-04

    Spectrochemical analyses of garden soils sampled in the Edinburgh and Dundee areas indicate that there is substantial contamination of urban soils with copper and boron. These soils were analyzed spectrochemically with respect to total copper and water-extractable boron content with the view of comparing the levels obtained in urban areas with levels in arable soils in rural areas. The results indicate that urban garden soils contain about four times as much copper and two to three times as much water-soluble boron as rural arable soils. The existence of such a marked disparity between the levels of two potentially toxic elements in urban and rural areas is evidence of slow poisoning of the soil environment in built-up areas and is cause for concern. While the major source of contamination of soils with copper and boron is still a matter for speculation, it is probable that the addition of soot to garden soils and the fall-out of sooty material in built-up areas where atmospheric pollution is a problem make a substantial contribution to the water-extractable boron content of urban soils. Three samples of soot from domestic chimneys, obtained from independent sources, were found on analysis to contain 640, 650 and 555 p.p.m. water-extractable boron, and it is evident that the addition to soil of even small amounts of soot with a boron content of this order would have a marked effect on its water-extractable boron content.

  12. Growing evidence for human health benefits of boron

    Science.gov (United States)

    Growing evidence from numerous laboratories using a variety of experimental models shows that boron is a bioactive beneficial, perhaps essential, element for humans. Reported beneficial actions of boron include arthritis alleviation or risk reduction; bone growth and maintenance; central nervous sys...

  13. Low-dimensional boron structures based on icosahedron B12

    Science.gov (United States)

    Kah, C. B.; Yu, M.; Tandy, P.; Jayanthi, C. S.; Wu, S. Y.

    2015-10-01

    One-dimensional icosahedral boron chains and two-dimensional icosahedral boron sheets (icosahedral α, δ6, and δ4 sheets) that contain icosahedra B12 as their building units have been predicted in a computer simulation study using a state-of-the-art semi-empirical Hamiltonian. These novel low-dimensional icosahedral structures exhibit interesting bonding and electronic properties. Specifically, the three-center, two-electron bonding between icosahedra B12 of the boron bulk (rhombohedral boron) transforms into a two-center bonding in these new allotropes of boron sheets. In contrast to the previously reported stable buckled α and triangular boron monolayer sheets, these new allotropes of boron sheets form a planar network. Calculations of electronic density of states (DOS) reveal a semiconducting nature for both the icosahedral chain and the icosahedral δ6 and δ4 sheets, as well as a nearly gapless (or metallic-like) feature in the DOS for the icosahedral α sheet. The results for the energy barrier per atom between the icosahedral δ6 and α sheets (0.17 eV), the icosahedral δ6 and δ4 sheets (0.38 eV), and the icosahedral α and δ4 sheets (0.27 eV), as indicated in the respective parentheses, suggest that these new allotropes of boron sheets are relatively stable.

  14. Predicted phase diagram of boron-carbon-nitrogen

    Science.gov (United States)

    Zhang, Hantao; Yao, Sanxi; Widom, Michael

    2016-04-01

    Noting the structural relationships between phases of carbon and boron carbide with phases of boron nitride and boron subnitride, we investigate their mutual solubilities using a combination of first-principles total energies supplemented with statistical mechanics to address finite temperatures. Thus we predict the solid-state phase diagram of boron-carbon-nitrogen (B-C-N). Owing to the large energy costs of substitution, we find that the mutual solubilities of the ultrahard materials diamond and cubic boron nitride are negligible, and the same for the quasi-two-dimensional materials graphite and hexagonal boron nitride. In contrast, we find a continuous range of solubility connecting boron carbide to boron subnitride at elevated temperatures. An electron-precise ternary compound B13CN consisting of B12 icosahedra with NBC chains is found to be stable at all temperatures up to melting. It exhibits an order-disorder transition in the orientation of NBC chains at approximately T =500 K. We also propose that the recently discovered binary B13N2 actually has composition B12.67N2 .

  15. BORON NITRIDE CAPACITORS FOR ADVANCED POWER ELECTRONIC DEVICES

    Energy Technology Data Exchange (ETDEWEB)

    N. Badi; D. Starikov; C. Boney; A. Bensaoula; D. Johnstone

    2010-11-01

    This project fabricates long-life boron nitride/boron oxynitride thin film -based capacitors for advanced SiC power electronics with a broad operating temperature range using a physical vapor deposition (PVD) technique. The use of vapor deposition provides for precise control and quality material formation.

  16. New applications of the interaction between diols and boronic acids

    NARCIS (Netherlands)

    Duval, F.L.

    2015-01-01

    Florine Duval - New applications of the interaction between diols and boronic acids – Summary Chapter 1 introduces the theory and known applications of the interaction between boronic acids and diols, and explains the context of this thesis. Diagnosis of depre

  17. Progress in preparation, properties and application of boron nitride nanomaterials

    Science.gov (United States)

    Wang, Youjun; Han, Jiaqi; Li, Yanjiao; Chen, Hao

    2017-08-01

    Boron nitride nanomaterials have attracted much and more interest in scientific research workers because of their excellent physical and chemical properties. They have become an important research hotspot in today's materials field. In this paper, boron nitride nanoparticles, "fullerenes", nanotubes, nanoribbons and Nano sheets were reviewed in terms of preparation methods, properties and potential applications.

  18. Vacancy complexes in carbon and boron nitride nanotubes

    CSIR Research Space (South Africa)

    Mashapa, MG

    2012-10-01

    Full Text Available The effect of divacancies on the stability, structural and electronic properties of carbon and boron nitride nanotubes is studied using the ab initio density functional method. VBBN is more stable in the boron-rich and less stable in the nitrogen...

  19. The investigation of parameters affecting boron removal by electrocoagulation method

    Energy Technology Data Exchange (ETDEWEB)

    Yilmaz, A. Erdem [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey)]. E-mail: aerdemy@atauni.edu.tr; Boncukcuoglu, Recep [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey); Kocakerim, M. Muhtar [Department of Chemical Engineering, 25240, Atatuerk University, Faculty of Engineering Erzurum (Turkey); Keskinler, Buelent [Department of Environmental Engineering, Gebze Institute of Technology, Gebze/Kocaeli 41400 (Turkey)

    2005-10-17

    Boron removal from wastewaters by electrocoagulation using aluminum electrode material was investigated in this paper. Several working parameters, such as pH, current density, boron concentration and type and concentration of supporting electrolyte were studied in an attempt to achieve a higher removal capacity. The experiments were carried out by keeping the pH of solution constant and optimum pH of solution was determined 8.0 for the aluminum electrode. Although energy consumption increased with decreasing boron concentration, which conductivity of these solutions were low, boron removal efficiency was higher at 100 mg/L than that of 1000 mg/L. Current density was an important parameter affecting removal efficiency. Boron removal efficiency and energy consumption increased with increasing current density from 1.2 to 6.0 mA/cm{sup 2}. The types of different supporting electrolyte were experimented in order to investigate to this parameter effect on boron removal. The highest boron removal efficiency, 97%, was found by CaCl{sub 2}. Added CaCl{sub 2} increased more the conductivity of solution according to other supporting electrolytes, but decreased energy consumption. The results showed to have a high effectiveness of the electrocoagulation method in removing boron from aqueous solutions.

  20. Synthesis, characterization, and antifungal activity of boron-containing thiosemicarbazones.

    Science.gov (United States)

    Hicks, Justin W; Kyle, Christian B; Vogels, Christopher M; Wheaton, Susan L; Baerlocher, Felix J; Decken, Andreas; Westcott, Stephen A

    2008-11-01

    Addition of thiosemicarbazide, 4-allylthiosemicarbazide, and 4-phenylthiosemicarbazide to (formylphenyl)boronic acids affords a series of thiosemicarbazones containing boronic acids. Addition of 2-formylphenylboronic acid to the thiosemicarbazides gave the corresponding cyclic 2,3,1-benzodiazaborines. All new compounds have been investigated for potential antifungal activity.

  1. Method for removal of phosgene from boron trichloride

    Science.gov (United States)

    Freund, S.M.

    1983-09-20

    Selective ultraviolet photolysis using an unfiltered mercury arc lamp has been used to substantially reduce the phosgene impurity in a mixture of boron trichloride and phosgene. Infrared spectrophotometric analysis of the sample before and after irradiation shows that it is possible to highly purify commercially available boron trichloride with this method. 5 figs.

  2. New applications of the interaction between diols and boronic acids

    NARCIS (Netherlands)

    Duval, F.L.

    2015-01-01

    Florine Duval - New applications of the interaction between diols and boronic acids – Summary Chapter 1 introduces the theory and known applications of the interaction between boronic acids and diols, and explains the context of this thesis. Diagnosis of

  3. Determination of boron in silicates after ion exchange separation

    Science.gov (United States)

    Kramer, H.

    1955-01-01

    Existing methods for the determination of boron in silicates are not entirely satisfactory. Separation as the methyl ester is lengthy and frequently erratic. An accurate and rapid method applicable to glass, mineral, ore, and water samples uses ion exchange to remove interfering cations, and boron is determined titrimetrically in the presence of mannitol, using a pH meter to indicate the end point.

  4. Finite Element Analysis Of Boron Diffusion In Wood

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Hoffmeyer, Preben; Bechgaard, Carl;

    2002-01-01

    The coupled heat and mass transfer equations for air, water and heat transfer are supplemented with a conservation equation for an additional species representing the concentration of boron in wood. Boundary conditions for wood-air. wood-soil and wood-boron interfaces arc discussed and finally th...

  5. The effects of boron management on soil microbial population and ...

    African Journals Online (AJOL)

    Administrator

    2011-06-15

    Jun 15, 2011 ... boron content of soil as maximum boron release corresponds with the highest microbial activity. The objective of .... different levels of B fertilizers on microbial population. (bacteria, fungi .... Urease enzyme (UE) activity was assayed by using urea solution .... g-1 soil 2h-1) and 0 kg ha-1 (control) B application.

  6. Interpretation of ionospheric F-region structures in the vicinity of ionisation troughs observed by satellite radio tomography

    Directory of Open Access Journals (Sweden)

    G. A. Aladjev

    Full Text Available Tomographic images of the spatial distribution of electron density in the ionospheric F-region are presented from the Russian-American Tomography Experiment (RATE in November 1993 as well as from campaigns carried out in northern Scandinavia in November 1995 and in Russia in April 1990. The reconstructions selected display the ionisation troughs above the tomographic chains of receivers during geomagnetically quiet and disturbed periods. Two mathematical models of the high-latitude ionosphere developed in the Polar Geophysical Institute have been applied for interpretation of the observed tomographic images.

    Key words. Ionosphere (electric fields and currents; ion chemistry and composition; plasma convection

  7. The ENEA calibration service for ionising radiations; Il centro di taratura per le radiazioni ionizzanti di Bologna. Parte 1: Fotoni

    Energy Technology Data Exchange (ETDEWEB)

    Monteventi, F.; Sermenghi, I. [ENEA, Centro Ricerche Ezio Clementel, Bologna (Italy). Dipt. Ambiente

    1999-07-01

    The report describes all the facilities available at the the service of the ENEA Calibration Service for Ionising Radiations at Bologna (Italy). It gives a detailed description of all equipment qualified for photon fields metrology including the secondary standards and the calibration procedures performed for radiation monitoring devices and dosemeters. [Italian] Il presente lavoro descrive i servizi e le attivita' del Centro di Taratura dell'ENEA di Bologna, in particolare delle attrezzature qualificate per la metrologia fotonica, dei campioni di misura e delle procedure adottate per la taratura degli strumenti e dei dosimetri.

  8. Current status of matrix-assisted laser desorption ionisation-time of flight mass spectrometry in the clinical microbiology laboratory.

    Science.gov (United States)

    Kok, Jen; Chen, Sharon C A; Dwyer, Dominic E; Iredell, Jonathan R

    2013-01-01

    The integration of matrix-assisted laser desorption ionisation-time of flight mass spectrometry (MALDI-TOF MS) into many clinical microbiology laboratories has revolutionised routine pathogen identification. MALDI-TOF MS complements and has good potential to replace existing phenotypic identification methods. Results are available in a more clinically relevant timeframe, particularly in bacteraemic septic shock. Novel applications include strain typing and the detection of antimicrobial resistance, but these are not widely used. This review discusses the technical aspects, current applications, and limitations of MALDI-TOF MS.

  9. Capillary electrophoresis with electrospray ionisation-mass spectrometry for the characterisation of degradation products in aged papers.

    Science.gov (United States)

    Dupont, Anne-Laurence; Seemann, Agathe; Lavédrine, Bertrand

    2012-01-30

    A methodology for capillary electrophoresis/electrospray ionisation mass spectrometry (CE/ESI-MS) was developed for the simultaneous analysis of degradation products from paper among two families of compounds: low molar mass aliphatic organic acids, and aromatic (phenolic and furanic) compounds. The work comprises the optimisation of the CE separation and the ESI-MS parameters for improved sensitivity with model compounds using two successive designs of experiments. The method was applied to the analysis of lignocellulosic paper at different stages of accelerated hygrothermal ageing. The compounds of interest were identified. Most of them could be quantified and several additional analytes were separated.

  10. Evaluation of a pulse-discharge helium ionisation detector for the determination of neon concentrations by gas chromatography.

    Science.gov (United States)

    Lasa, J; Mochalski, P; Pusz, J

    2004-05-07

    A pulse-discharge helium ionisation detector, PDHID (Valco, PD-D2-I) with sample introduced to the discharge zone is shown to be applicable for reliable determinations of neon by gas chromatography. The detection level of 80 pg was obtained, but the dependence between detector response and neon mass was non-linear. However, for the discharge gas doped with 33 ppm of neon, a linear response to the neon mass up to 10(-5) g and the detection level of 0.5 ng were obtained. The method can be used for measuring neon concentrations in groundwater systems for hydrogeological purposes.

  11. Thermally and optically stimulated luminescence of AlN-Y2O3 ceramics after ionising irradiation

    DEFF Research Database (Denmark)

    Trinkler, L.; Bos, A.J.J.; Winkelman, A.J.M.;

    1999-01-01

    Thermally (TL) and optically stimulated luminescence (OSL) were studied in AlN-Y2O3 ceramics after irradiation with ionising radiation. The extremely high TL sensitivity (approximately 60 times the sensitivity of LiF:Mg,Tl (TLD-100)) makes AlN-Y2O3 ceramics attractive as a TLD material. However......, an essential drawback of AlN-Y2O3 is its high fading rate. Special attention has been focused on understanding and improving the fading properties. In particular, the influence of the ceramics production conditions and the additive concentration on the fading rate have been studied. Experimental results...

  12. Predicting the effects of ionising radiation on ecosystems by a generic model based on the Lotka-Volterra equations

    Energy Technology Data Exchange (ETDEWEB)

    Monte, Luigi [ENEA CR Casaccia, Via P. Anguillarese 301 00100 Rome (Italy)], E-mail: luigi.monte@enea.it

    2009-06-15

    The present work describes a model for predicting the population dynamics of the main components (resources and consumers) of terrestrial ecosystems exposed to ionising radiation. The ecosystem is modelled by the Lotka-Volterra equations with consumer competition. Linear dose-response relationships without threshold are assumed to relate the values of the model parameters to the dose rates. The model accounts for the migration of consumers from areas characterised by different levels of radionuclide contamination. The criteria to select the model parameter values are motivated by accounting for the results of the empirical studies of past decades. Examples of predictions for long-term chronic exposure are reported and discussed.

  13. Predicting the effects of ionising radiation on ecosystems by a generic model based on the Lotka-Volterra equations.

    Science.gov (United States)

    Monte, Luigi

    2009-06-01

    The present work describes a model for predicting the population dynamics of the main components (resources and consumers) of terrestrial ecosystems exposed to ionising radiation. The ecosystem is modelled by the Lotka-Volterra equations with consumer competition. Linear dose-response relationships without threshold are assumed to relate the values of the model parameters to the dose rates. The model accounts for the migration of consumers from areas characterised by different levels of radionuclide contamination. The criteria to select the model parameter values are motivated by accounting for the results of the empirical studies of past decades. Examples of predictions for long-term chronic exposure are reported and discussed.

  14. Headspace analysis of new psychoactive substances using a Selective Reagent Ionisation-Time of Flight-Mass Spectrometer

    OpenAIRE

    2014-01-01

    The rapid expansion in the number and use of new psychoactive substances presents a significant analytical challenge because highly sensitive instrumentation capable of detecting a broad range of chemical compounds in real-time with a low rate of false positives is required. A Selective Reagent Ionisation-Time of Flight-Mass Spectrometry (SRI-ToF-MS) instrument is capable of meeting all of these requirements. With its high mass resolution (up to m/Δm of 8000), the application of variations in...

  15. A computational study of carbon dioxide adsorption on solid boron.

    Science.gov (United States)

    Sun, Qiao; Wang, Meng; Li, Zhen; Du, Aijun; Searles, Debra J

    2014-07-07

    Capturing and sequestering carbon dioxide (CO2) can provide a route to partial mitigation of climate change associated with anthropogenic CO2 emissions. Here we report a comprehensive theoretical study of CO2 adsorption on two phases of boron, α-B12 and γ-B28. The theoretical results demonstrate that the electron deficient boron materials, such as α-B12 and γ-B28, can bond strongly with CO2 due to Lewis acid-base interactions because the electron density is higher on their surfaces. In order to evaluate the capacity of these boron materials for CO2 capture, we also performed calculations with various degrees of CO2 coverage. The computational results indicate CO2 capture on the boron phases is a kinetically and thermodynamically feasible process, and therefore from this perspective these boron materials are predicted to be good candidates for CO2 capture.

  16. Synthesis and photoluminescence property of boron carbide nanowires

    Institute of Scientific and Technical Information of China (English)

    Bao Li-Hong; Li Chen; Tian Yuan; Tian Ji-Fa; Hui Chao; Wang Xing-Jun; Shen Cheng-Min; Gao Hong-Jun

    2008-01-01

    Large scale, high density boron carbide nanowires have been synthesized by using an improved carbothermal reduction method with B/B2O3/C powder precursors under an argon flow at 1100~C. The boron carbide nanowires are 5-10 μm in length and 80-100 nm in diameter. Transmission electron microscopy (TEM) and selected area electron diffraction (SAED) characterizations show that the boron carbide nanowire has a B4C rhombohedral structure with good crystallization. The Raman spectrum of the as-grown boron carbide nanowires is consistent with that of a B4C structure consisting of B11C icosahedra and C-B-C chains. The room temperature photoluminescence spectrum of the boron carbide nanowires exhibits a visible range of emission centred at 638 nm.

  17. APPLICATION OF BORON MODIFIED SILICA SOL ON RETENTION AND DRAINAGE

    Institute of Scientific and Technical Information of China (English)

    JinxiaMa; YuxiuPeng; ZhongzhengLi

    2004-01-01

    In this paper it was studied that these dosage effectsof CPAM, cationic starch,boron modified silica sol(BMS), A12(SO4)3, pH value and electrolyte on theretention and drainage of different microparticulatesystems including CPAM, cationic starch and boronsilica sol. The research results indicated that CPAMhad no good retention when used with boron silicasol. The best retention efficiency was the micropar-ticulate system of CPAM + cationic starch withboron modified silica sol; Secondly was that ofcationic starch with boron modified silica sol; Theworst was that of CPAM with boron modified silicasol. The retention efficiency had no relation with theaddition order between CPAM and cationic starch. Itwas also found that the microparticulate retentionsystem of boron modified silica sol could be used inalum-rosin sizing and in acidity, neutral or alkalinepapermaking conditions. This system also could beused with close circulate water so that it could reducethe water pollution and waste.

  18. Additive Manufacturing of Dense Hexagonal Boron Nitride Objects

    Energy Technology Data Exchange (ETDEWEB)

    Marquez Rossy, Andres E [ORNL; Armstrong, Beth L [ORNL; Elliott, Amy M [ORNL; Lara-Curzio, Edgar [ORNL

    2017-05-12

    The feasibility of manufacturing hexagonal boron nitride objects via additive manufacturing techniques was investigated. It was demonstrated that it is possible to hot-extrude thermoplastic filaments containing uniformly distributed boron nitride particles with a volume concentration as high as 60% and that these thermoplastic filaments can be used as feedstock for 3D-printing objects using a fused deposition system. Objects 3D-printed by fused deposition were subsequently sintered at high temperature to obtain dense ceramic products. In a parallel study the behavior of hexagonal boron nitride in aqueous solutions was investigated. It was shown that the addition of a cationic dispersant to an azeotrope enabled the formulation of slurries with a volume concentration of boron nitride as high as 33%. Although these slurries exhibited complex rheological behavior, the results from this study are encouraging and provide a pathway for manufacturing hexagonal boron nitride objects via robocasting.

  19. Safety Assessment of Boron Nitride as Used in Cosmetics.

    Science.gov (United States)

    Fiume, Monice M; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

    2015-01-01

    The Cosmetic Ingredient Review Expert Panel (Panel) assessed the safety of boron nitride which functions in cosmetics as a slip modifier (ie, it has a lubricating effect). Boron nitride is an inorganic compound with a crystalline form that can be hexagonal, spherical, or cubic; the hexagonal form is presumed to be used in cosmetics. The highest reported concentration of use of boron nitride is 25% in eye shadow formulations. Although boron nitride nanotubes are produced, boron nitride is not listed as a nanomaterial used in cosmetic formulations. The Panel reviewed available chemistry, animal data, and clinical data and concluded that this ingredient is safe in the present practices of use and concentration in cosmetic formulations.

  20. Localization of dislocation-related luminescence centers in self-ion implanted silicon and effect of additional boron ion doping

    Energy Technology Data Exchange (ETDEWEB)

    Tetelbaum, D.I.; Mikhaylov, A.N.; Belov, A.I.; Korolev, D.S.; Shushunov, A.N.; Bobrov, A.I.; Pavlov, D.A. [Lobachevsky State University of Nizhni Novgorod (Russian Federation); Shek, E.I.; Sobolev, N.A. [Ioffe Physical Technical Institute, St. Petersburg (Russian Federation)

    2015-01-01

    The depth distribution of light-emitting centers of the D1 dislocation-related photoluminescence line (∝ 1.5 μm) in silicon implanted with Si{sup +} ions and annealed at 1100 C in the oxidizing chlorine-containing atmosphere has been investigated by means of the layer-by-layer chemical etching. It is established with the application of cross-sectional transmission electron microscopy that the main contribution to the D1 line is made by the centers located at the depths of up to ∝ 150 nm, i.e. in the region of Si{sup +} ion ranges, whereas the dislocations produced by Si{sup +} implantation and annealing at 1100 C penetrate to the depth of ∝ 1000 nm. Additional boron ion doping with subsequent annealing at 800 C in N{sub 2} atmosphere improves the emission in comparison with the undoped but annealed reference sample, however the additional annealing at 800 C per se results in the photoluminescence weakening. The dependence of the D1 line intensity on boron ion dose is found to be nonmonotonous. The interpretation of the obtained results is given in relation to the key role of selfinterstitials and boron impurity in the formation of radiative and nonradiative centers. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)