Long-term properties of bituminized waste products

International Nuclear Information System (INIS)

Snellman, M.; Valkiainen, M.

1985-10-01

This study is a survey of the factors of importance for long term behaviour of bituminized ion exchange resins. Phenomena occurring in bituminized waste products affected by the treatment, storage and disposal are identified. Test methods have been developed for characterizing product properties, which are important for the long-term behaviour. The long-term properties of bituminized ion-exchange resins are studied in a repository environment with access of water equilibrated with concrete. In these circumstances the most important properties are ralated to the interactions of bituminized waste with the surrounding barriers. The most important phenomena are water uptake due to rehydration of the resins and subsequent swelling of the product. (author)

Development of a methodology to determine the radionuclide inventory of bituminized waste packages; Entwicklung eines Verfahrens zur Bestimmung des Nuklid-Inventars in bituminierten Abfallgebinden

Energy Technology Data Exchange (ETDEWEB)

Mesalic, E.; Kortmann, F.; Lierse von Gostomski, C.

2016-02-22

For the declaration of the nuclide-inventory of bituminous waste there are currently no standardized sampling-, dissolving- and analysis methods such as for cemented waste, resins and sludge is the case. The aim of this project was to develop a method for the destructive sampling and subsequent radionuclide separation and declaration for the characterization of bituminized waste. The qualitative and quantitative results of non-destructive measurement methods (segmented gamma scanning in combination with digital radiography and gamma transmission computed tomography) are compared with results from destructive analysis. The project involves: - the development of a routine method for sampling bituminized 200-L-waste containers, exemplarily applied to real drums with bituminized waste. - the development of destructive treatment and preparation methods for the obtained bitumen samples with subsequent analysis for: - Alpha emitters, e.g. Pu-, Am- and Cm-isotopes, - Beta/Gamma emitters, e.g. Co-60, Cs-137, - pure Beta emitters, e.g. Sr-90. - Comparison of the results from destructive and non-destructive methods.

On the microstructure of bituminous binders

NARCIS (Netherlands)

Fischer, H.R.; Dillingh, E.C.; Hermse, C.G.M.

2014-01-01

The objective of this work is to study the common features and the evolution of microstructures of bituminous binders regardless of their grade (PEN 10/20 to 160/220) and source/origin using the atomic force microscope operated in phase contrast mode. All bituminous binders show the same

Development of a method to determine the nuclide inventory in bituminized waste packages; Entwicklung eines Verfahrens zur Bestimmung des Nuklidinventars in bituminierten Abfallgebinden

Energy Technology Data Exchange (ETDEWEB)

Mesalic, E.; Kortman, F.; Lierse von Gostomski, C. [Technische Univ. Muenchen, Garching (Germany). Zentrale Technisch-Wissenschaftliche Betriebseinheit Radiochemie Muenchen (RCM)

2014-01-15

Until the 1980s, bitumen was used as a conditioning agent for weak to medium radioactive liquid waste. Its use can be ascribed mainly to the properties that indicated that the matrix was optimal. However, fires broke out repeatedly during the conditioning process, so that the method is meanwhile no longer permitted in Germany. There are an estimated 100 waste packages held by the public authorities in Germany that require a supplementary declaration. In contrast to the common matrices, such as for example resins or sludges, there is still no standardized technology for taking samples and subsequently determining the radio-nuclide for bitumen. Aspects, such as the thermoplastic behaviour, make determining the nuclide inventory more difficult in bituminized waste packages. The development of a standardized technology to take samples with a subsequent determination of the radio-nuclide analysis is the objective of a project funded by the BMBF. Known, new methods, specially developed for the project, are examined on inactive bitumen samples and then transferred to active samples. At first non-destructive methods are used. The resulting information forms an important basis to work out and apply destructive strategy for sampling and analysis. Since the project is on-going, this report can only address the development of the sampling process. By developing a sampling system, it will be possible to take samples from an arbitrary selected location of the package across the entire matrix level and thus gain representative analysis material. The process is currently being optimized. (orig.)

Pilot study approach and qualification dossier components

International Nuclear Information System (INIS)

Ammirato, F.; Ashwin, P.

2000-01-01

The aim of the Pilot Project is to evaluate the IAEA Guidelines and methodology for the benefit of IAEA Member States trough a simulation of qualification activities. The Project is based on a real component and available data - NPP Kozloduy unit 5, weld 3. The initial phase is limited to the Qualification dossier. The Project relies on the input from the team members and Member States. Team organization and responsibilities are presented. The components of the Qualification Dossier (technical specification, inspection procedure and preliminary review, qualification procedure) and their current status are also presented. A comparison is done with their qualification programs. The characteristics of performance demonstrations are discussed. The results show that the teamwork has been successful and the IAEA methodology covers all situations. It is expected that the End Project will become 'Benchmark's' for future qualification activities

Leachability of bituminized radioactive waste. Literature survey

International Nuclear Information System (INIS)

Akimoto, Toshiyuki; Nakayama, Shinichi; Iida, Yoshihisa; Nagano, Tetsushi

1999-02-01

Bituminized radioactive waste that will be returned from COGEMA, France is planned to be disposed of in deep geologic repository in Japan. Data on leachability of radionuclides from bituminized waste are required for the performance assessment of the disposal. We made a literature survey on bitumen and bituminized radioactive waste, placing emphasis on leach tests and leach data in terms of geologic disposal. This survey revealed that reliable leach data on transuranium elements and data obtained under reducing conditions that is characteristic to deep underground are lacking. (author). 64 refs

Climate and economy. Climate Policy Dossier

International Nuclear Information System (INIS)

Gielen, A.M.; Koutstaal, P.R.; De Groot, H.L.F.; Tang, P.J.G.

2001-01-01

In this introductory article an overview is given of what can be expected in this dossier on climate policy in the Netherlands, focusing on the economic analysis of climate policy and climatic change. Attention will be paid to flexible mechanisms to reduce the costs of such policy and visions of interested parties. 1 ref

Bituminization of low- and medium-level radioactive wastes

International Nuclear Information System (INIS)

Lefillatre, G.

1976-01-01

French operations are presented concerning mainly: the bituminization of radioactive wastes produced in light water reactors; the direct bituminization of liquid effluents without concentration; the experiments carried out for 18 months on the land burial of concentrates solidified by bitumen into blocks of 100 liters. The knowledge acquired in France is exposed: in Valduc and in Saclay with facilities equipped with thin film evaporators and in Marcoule with the conditioning of trilaurylamine and tributyl-phosphate. At last the Cadarache bituminization [fr

Apparatus for carbonization of bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Krupa, G

1924-08-25

Apparatus is described for carbonization of bituminous fuels and bituminous shale, in which the material to be carbonized slips continuously over sloping surfaces of a retort arranged in a zigzag and thereby it is exposed to a continuously increasing heating. The apparatus is characterized by the sloping surface being of a boxlike solid hearth with internal heating through which every hearth can be heated directly to a determined constant degree of heat.

Response Modelling of Bitumen, Bituminous Mastic and Mortar

NARCIS (Netherlands)

Woldekidan, M.F.

2011-01-01

This research focuses on testing and modelling the viscoelastic response of bituminous binders. The main goal is to find an appropriate response model for bituminous binders. The desired model should allow implementation into numerical environments such as ABAQUS. On the basis of such numerical

Nagra technical report 14-02, geological basics - Dossier V - Hydro-geological conditions

International Nuclear Information System (INIS)

Traber, D.; Gautschi, A.; Marschall, P.; Becker, J.; Waber, N.

2014-01-01

This dossier is the fifth of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. Dossier V looks at hydro-geological considerations in North-Western Switzerland. Rock layers in the region and their hydrological properties are examined. Ground-water and deeper lying aquifers in the various rock formations are discussed. The specific hydrology in the proposed areas for nuclear waste depositories is looked at, including infiltration and exfiltration zones and gradients

Bituminization of low- and intermediate-level radioactive concentrates

International Nuclear Information System (INIS)

Breza, M.; Krejci, F.; Timulak, J.; Tibensky, L.

1985-01-01

The results and experiences are summed up from the research and development of the technology of bituminization of low- and intermediate-level radioactive concentrates generated in the operation of nuclear power plants with WWER-440 reactors. The experiments took place on a pilot plant bituminization line with various model solutions at an evaporator capacity of 70, 100 and 140 litres per hour. The composition of the solutions changed in dependence on the knowledge of the composition of actual concentrates in the V-1 nuclear power plant at Jaslovske Bohunice. The following factors were studied in the concentrate: the effect of its pH, its borate content and content of metal carbonates, the content of organic acid salts, the content of detergents, etc., on the process of bituminization. Physico-chemical conditions are described under which the operation of the evaporator was fail-safe and filling of the bituminization product with salts homogeneous. A low water content of up to 1% was achieved. The properties of the bituminization product were negatively affected by a high level of heavy metal oxides, surfactants, oxalates and citrates. In order to improve the properties of the product it will be necessary to replace bitumen emulsion Silembit-60 used as reinforcement matrix, by a different type of bitumen. (Z.M.)

2005 dossier. ANDRA's researches on the geological disposal of high-level and long-lived radioactive wastes. Results and perspectives

International Nuclear Information System (INIS)

2005-06-01

This document makes a status of the researches carried out by the French national agency of radioactive wastes (ANDRA) about the geologic disposal of high-level and long-lived radioactive wastes in deep geologic formations (argilites and granites). Content: 1 - Research on deep disposal of radioactive waste: general interest task: Legislative framework, ANDRA scientific objectives, Inspections and assessments; 2 - Designing a safe and reversible disposal system: Repository safety, Reversibility: an essential requirement; 3 - Clay Research on a repository in a clay formation, A long research programme, Dossier 2005 Argile; 4 - Meuse/Haute-Marne site clay: Expected properties of the rock formation, Choice of argillite, Meuse/Haute-Marne site, Conclusions from 10 years of research at the Meuse/Haute-Marne site; 5 - Repository installations: Safe and reversible architecture, Disposal of B waste, Disposal of C waste, Possible disposal of spent fuel (CU); 6 - The disposal facility in operation: From waste packages reception to their disposal in cells, Stages of the progressive closure of engineered structures; 7 - Reversible management: Freedom of choice for future generations, Various closure stages; 8 - Long-term evolution of the repository: Apprehending the repository complexity Main evolutions expected, Slow and limited release of radioactive substances; 9 - Repository safety and impact on man: Several evolution scenarios, Normal evolution, Altered evolution; 10 - Granite Research on a repository in a granite formation: A global approach, Scientific co-operations, Dossier 2005 Granite; 11 - Characteristics of French granite formations: What properties are required for a repository?, Different types of granite formations; 12 - Repository installations: Repository design adapted to granite fractures, Clay seals to prevent water flows, Waste disposal packages ensuring long-term leak-tightness, Physical and chemical environment favourable for waste packages, Architecture

Evaluation of mastic in bituminous mixtures

OpenAIRE

Silva, Hugo Manuel Ribeiro Dias da; Pais, Jorge C.; Pereira, Paulo A. A.

2002-01-01

The efficiency of the asphalt-aggregate bond is one of the key factors which affects the mechanical resistance of bituminous mixtures and a better understanding of its performance allows the behaviour of mixture to be more accurately predicted. The asphalt-aggregate bond depends on the properties of the mastic and the mixture of fine aggregate and bitumen which bonds itself to the larger sized particles within the bituminous mixture. This mastic plays an im-portant role in the asphalt-aggr...

Distillation of bituminous substances

Energy Technology Data Exchange (ETDEWEB)

du Buisson, M A.B.B.

1845-06-23

New and improved methods are described for the distillation of bituminous schistus and other bituminous substances, as well as for the purification, rectification, and preparation necessary for the employment of the productions obtained by such distillation for various useful purposes. This invention consists, first, in the arrangement and construction of furnace or apparatus for the distillation of schistus, and (any) other bituminous rocks. This furnace is made of circular brick-work, and is provided with the requisite number of fires placed round the circumference. The retort is of a conical or funnel shape, and when ready for use, has the appearance of one inverted cone being placed within a larger cone, in such a manner as to leave a space between the two cones for the reception of the schistus. Both cones are capable of being closed at their apexes, and their mouths, which are placed upwards, are connected together, and hermetically closed by a flat ring. The flame draft is caused to impinge against the lower portion of the outer cone and ascending, turns over the upper edge and descends within the inner cone to the mouth of the chimney, which is placed in the interior, and as low as may be convenient. A third cone is so placed within the inner cone as to cause the flame draft, in its descent, to bind against the surface of the retort.

On inflammability and explosiveness in bituminization

International Nuclear Information System (INIS)

Zakharova, K.P.; Kulichenko, V.V.; Nazin, E.R.; Sadovnikov, Yu.N.; Ukke, O.V.

1978-01-01

Results of a study of safety in the bituminization of radioactive wastes and storage of the final product are presented. The temperature of interaction of bitumen with one of the basic waste components, i.e. sodium nitrate, is 385-408 deg C. A noticeable decrease in this value is observed only in the presence of an alkali. The introduction of an additive in bitumen does not increase its inflammability as measured by a number of indicators. Bituminous substances containing less than 15% bitumen are capable of detonating, while those with a higer percentage are not

Bituminous breeds oil of Binagady deposite of Azerbaijan

International Nuclear Information System (INIS)

Djabbarova, L.U.; Ibadov, N.A.; Akhmedbekova, S.

2010-11-01

Full text: Processing of such kinds of raw materials like natural bituminous breeds and combustible shales at present represents as a new and perspective direction for satisfaction of growing demand with motor fuels and chemical raw materials. There are 200 million tons of bituminous breeds in 11 deposits in Azerbaijan. Bitumenkeeping soils can be used while road construction in natural form, as a component of asphalt concrete mixes for coverings and basis. Bitumens are irreplaceable waterproofing material that has a wide use in a nuclear power industry by the help of if its resistance to radiation impact, for entombment of radioactive materials. There were presented the results of carried out works about experimental researches of formation laws of gaseous products from bituminous breeds of Kirmaki deposit site of Azerbaijan. Radiation-thermal transformations of bituminous breeds and liquid products of their thermal decomposition have been studied in a wide range of temperature change, absorbed dose and dose capacity. Formation kinetics had been studied, radiation chemical outputs defined, also the structure of gaseous products of disintegration. [ru

Evaluation of bituminized waste reactivity

International Nuclear Information System (INIS)

Camaro, S.; Moulinier, D.

2000-01-01

The bituminization process has been used for conditioning low and medium level (LML) radioactive waste, particularly to immobilize coprecipitation slurries and evaporation concentrates generated by effluent treatment. The process consists in mixing bitumen matrix with inactive soluble and slightly soluble salts added to insolubilize the radionuclides or resulting from the neutralization of acid effluents. This operation is performed at a sufficient temperature - depending on waste composition and bitumen grade to ensure the flow of the resulting mixture into metal containers. Exothermicity due to salts/salts or salts/bitumen reactions depending on the type of waste can be induced during or after the mixing step. This could produce an additional heat emission that the drum must be able to release to avoid a potentially incidental pattern with ignition risk, explaining why the CEA has been involved in evaluating the thermal reactivity of bituminized waste and its repercussions on the bituminization process. Given the difficulty of discriminating each exothermal reaction, the characterization of a global reactivity appears as a further precautionary measure, in addition to the definition of a working safety margin. The CEA has accordingly developed studies on this aspect. The article discusses the experimental methodology developed for the determination of the global reactivity. (authors)

Bituminization plant Jaslovske Bohunice

International Nuclear Information System (INIS)

1999-01-01

In this leaflet the principle of the bituminization plant for radioactive concentrate (the intermediate liquid radioactive waste generated during the NPP A1, V-1, V-2 operations) solidification used in the Bohunice Radwaste Treatment Centre (BSC RAO) is presented

2005 dossier. ANDRA's researches on the geological disposal of high-level and long-lived radioactive wastes. Results and perspectives; Dossier 2005. Les recherches de l'Andra sur le stockage geologique des dechets radioactifs a haute activite et a vie longue. Resultats et perspectives

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-06-15

This document makes a status of the researches carried out by the French national agency of radioactive wastes (ANDRA) about the geologic disposal of high-level and long-lived radioactive wastes in deep geologic formations (argilites and granites). Content: 1 - Research on deep disposal of radioactive waste: general interest task: Legislative framework, ANDRA scientific objectives, Inspections and assessments; 2 - Designing a safe and reversible disposal system: Repository safety, Reversibility: an essential requirement; 3 - Clay Research on a repository in a clay formation, A long research programme, Dossier 2005 Argile; 4 - Meuse/Haute-Marne site clay: Expected properties of the rock formation, Choice of argillite, Meuse/Haute-Marne site, Conclusions from 10 years of research at the Meuse/Haute-Marne site; 5 - Repository installations: Safe and reversible architecture, Disposal of B waste, Disposal of C waste, Possible disposal of spent fuel (CU); 6 - The disposal facility in operation: From waste packages reception to their disposal in cells, Stages of the progressive closure of engineered structures; 7 - Reversible management: Freedom of choice for future generations, Various closure stages; 8 - Long-term evolution of the repository: Apprehending the repository complexity Main evolutions expected, Slow and limited release of radioactive substances; 9 - Repository safety and impact on man: Several evolution scenarios, Normal evolution, Altered evolution; 10 - Granite Research on a repository in a granite formation: A global approach, Scientific co-operations, Dossier 2005 Granite; 11 - Characteristics of French granite formations: What properties are required for a repository?, Different types of granite formations; 12 - Repository installations: Repository design adapted to granite fractures, Clay seals to prevent water flows, Waste disposal packages ensuring long-term leak-tightness, Physical and chemical environment favourable for waste packages, Architecture

Carbonizing bituminous minerals

Energy Technology Data Exchange (ETDEWEB)

1921-05-01

A process for carbonizing bituminous minerals, like oil-shale, in a furnace with addition of air in the presence of heat-receiving material is characterized by the fact that to the feed such solid or liquid material (with the exception of oil) is added, which, through vaporization or heat-binding decomposition or conversion, hinders the establishment of excessive temperatures.

Reuse of steel slag in bituminous paving mixtures.

Science.gov (United States)

Sorlini, Sabrina; Sanzeni, Alex; Rondi, Luca

2012-03-30

This paper presents a comprehensive study to evaluate the mechanical properties and environmental suitability of electric arc furnace (EAF) steel slag in bituminous paving mixtures. A variety of tests were executed on samples of EAF slag to characterize the physical, geometrical, mechanical and chemical properties as required by UNI EN specifications, focusing additionally on the volumetric expansion associated with hydration of free CaO and MgO. Five bituminous mixtures of aggregates for flexible road pavement were designed containing up to 40% of EAF slag and were tested to determine Marshall stability and indirect tensile strength. The leaching behaviour of slag samples and bituminous mixtures was evaluated according to the UNI EN leaching test. The tested slag showed satisfactory physical and mechanical properties and a release of pollutants generally below the limits set by the Italian code. Tests on volume stability of fresh materials confirmed that a period of 2-3 months is necessary to reduce effects of oxides hydration. The results of tests performed on bituminous mixtures with EAF slag were comparable with the performance of mixtures containing natural aggregates and the leaching tests provided satisfactory results. Copyright © 2012 Elsevier B.V. All rights reserved.

Bituminization of liquid radioactive wastes. Part 1

International Nuclear Information System (INIS)

Gradev, G.D.; Ivanov, V.I.; Stefanova, I.G.; Milusheva, A.G.; Guteva, E.S.; Zhelyazkov, V.T.; Stefanov, G.I.; G'oshev, G.S.

1991-01-01

Salt-bitumen products are produced by the method of 'hot mixing' of some Bulgarian bitumens (road bitumen PB 66/99 and the hydroinsulating bitumen HB 80/25) and salts (chlorides, sulphates, borates, salt mixtures modelling the liquid waste from nuclear power plants) in different ratios to determine the optimum conditions for bituminization of liquid radioactive waste. The penetration, ductility and softening temperature were determined. The sedimentation properties and the thermal resistance of the various bitumen-salt mixtures were studied. The most suitable bitumen for technological research at the Kozloduy NPP was found to be the road bitumen PB 66/90 with softening temperature at 48 o C. The optimum amount of salts incorporated in the bitumen - about 45% - was found. No exothermal effects were observed in the bituminization process in the temperature range of up to 200 o C. The results obtained may be useful in the elaboration of a technology for bituminization of liquid radioactive wastes in the Kozloduy NPP. 4 tabs., 5 figs., 4 refs

Process and apparatus for distilling bituminous minerals

Energy Technology Data Exchange (ETDEWEB)

Veyrier, J A

1922-03-27

This process of distillation of bituminous minerals and particularly bituminous limestone is characterized by the fact that the minerals are introduced into the retort where they stand only the temperature necessary to distill the water and lighter oils that they contain and then are drawn out into the hearth and serve for heating the retort. The apparatus is characterized by the fact that the retort has a screw conveyor, placed in the flue of the hearth, supplied with a chamber for evacuation below this hearth.

Distilling bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Forrest, C N; Hayden, H P

1926-12-28

Bituminous materials such as heavy asphaltic residues from petroleum distillation or natural bitumens such as gilsonite, grahamite, etc. are distilled in presence of a carrier consisting of pieces of inert refractory material and by the heat generated by combustion of the coke which remains on the carrier after distillation. A vertical cylindrical retort, in which a wood and coal fire is first made, is charged with an inert refractory substance such as pumice stone, broken firebrick, burnt fire clay, carborundum, ash, etc. mixed with a bituminous substance, which, if fusible, may be melted and added in a rotary drum. The mixture passes downwards through the retort, first through regions in which the hydrocarbons are distilled and cracked and then through a region in which the remaining carbon is burnt by a limited supply of air and steam admitted through a grate. The inert material is discharged through a water seal and used again. Vapors, withdrawn from the retort though an outlet, pass through a heat intercharger and separator and are treated with a spray of sulfuric acid to separate ammonia in a scrubber, with water sprays to condense oil in scrubbers, and with oil in a scrubber.

Framework for replacing steel with aluminum fibers in bituminous mixes

NARCIS (Netherlands)

Pavlatos, N.; Apostolidis, P.; Scarpas, Athanasios

2018-01-01

This research explores the incentives for replacing steel fibers with aluminum fibers in fiber modified bituminous mixes. In this work the focus is on fiber modified bituminous mixes especially designed for induction heating. Inductive fibers are heated up because eddy currents are generated -

Nagra technical report 14-02, geological basics - Dossier III - Long-term geological developments

International Nuclear Information System (INIS)

Schnellmann, M.; Madritsch, H.

2014-01-01

This dossier is the third of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. Dossier III takes a look at long-term geological developments. Developments in the topography and river networks of northern Switzerland over the past five million years are looked at. Data and information derived from high-resolution models and compilations of gravel deposition, glacier developments and moraines are reviewed. Tectonic developments, seismological aspects and erosion are discussed. Their consequences for the long-term geological developments in the proposed depository areas are looked at

Bituminous and asphaltic membranes for radioactive waste repositories on land

International Nuclear Information System (INIS)

1988-03-01

The aim of the study has been to identify, within generic designs for waste facilities, areas where bituminous materials might be incorporated as a barrier. The report is presented in three sections: Part I - The properties of bitumen are described, with particular reference to the long-term behaviour of the material. The durability of bitumen is discussed, including aspects such as ageing, microbial degradation, chemical resistance and radiation resistance. Part II -The use of bituminous materials in hydraulic engineering is outlined. Much of this section of the report concentrates on the use of bituminous materials in embankment dams and reservoir construction. A review of material technology and construction techniques is presented and a detailed assessment made of the performance of the materials in service. Part III - Generic trench type radioactive waste repository designs incorporating bituminous materials are presented. Material and construction specifications for the designs are detailed, and a performance assessment presented. (author)

Special dossier: new energies

International Nuclear Information System (INIS)

Cassin, Fabrice; His, Stephane; Le Lidec, Frederic; Paillard, Michel; Vandevoorde, Patrick; Huby, Jean; Soetaert, Emmanuel; Bertiere, Francois; Zwierski, Didier; Kuntz, Michel; Mallet, Pierre; Leboucher, Nathalie; Isikveren, Murat; Vacher, Romain

2012-01-01

This special dossier about renewable energies is made of 14 contributions dealing with: wind turbines against radars, legal constraints on wind farms location (Fabrice Cassin); the sea, an ocean of wind energy (Stephane His); marine energies, a promising sector (Frederic Le Lidec); Gamesa, an integrated actor of the wind power industry; the great future of renewable marine energies (Michel Paillard); focus on wind power (Patrick Vandevoorde); wind power, a new industrial adventure (Jean Huby); hydropower, a renewed modernity (Emmanuel Soetaert); the new needs of tomorrows' cities (Francois Bertiere); the control of power consumption, a huge market in progress (Didier Zwierski, Michel Kuntz); in the heart of the smart grids revolution (Pierre Mallet); the smart-city, an established reality (Nathalie Leboucher); imagining solutions for the environment (Murat Isikveren); energy: towards a smart consumption (Romain Vacher)

Carbonizing bituminous materials

Energy Technology Data Exchange (ETDEWEB)

1924-03-11

A process for carbonizing bituminous materials, like mineral coal, brown coal, oil shale, and the like, by means of hot gass is characterized in that, these (gases) flush through the feed in the temperature-state above 450/sup 0/C, while below 450/sup 0/C they are led past the feed and act on it by heat conductivity, convection, and gas radiation or only by heat conduction.

State of the art report on bituminized waste forms of radioactive wastes

International Nuclear Information System (INIS)

Kim, Tae Kook; Shon, Jong Sik; Kim, Kil Jeong; Lee, Kang Moo; Jung, In Ha

1998-03-01

In this report, research and development results on the bituminization of radioactive wastes are closely reviewed, especially those regarding waste treatment technologies, waste solidifying procedures and the characteristics of asphalt and solidified forms. A new concept of the bituminization method is suggested in this report which can improve the characteristics of solidified forms. Stable solid forms with high leach resistance, high thermal resistance and good compression strength were produced by the suggested bituminization method, in which spent polyethylene from agricultural farms was added. This report can help further research and development of improved bituminized forms of radioactive wastes that will maintain long term stabilities in disposal sites. (author). 59 refs., 19 tabs., 18 figs

Development of bituminization process for radioactive wastes

International Nuclear Information System (INIS)

Segawa, Takeshi; Yamamoto, Masao; Miyao, Hidehiko; Mizuno, Ryukichi

1973-01-01

For the bituminization of radioactive wastes from a fuel reprocessing plant, the leachability, irradiation stability and burning property of bitumen products have been studied. Sodium nitrate was used for simulated evaporator concentrate, and mixed with distillation bitumen or blown bitumen; the sodium nitrate content in the mixture was 30 to 60 wt%. The distillation bitumen is superior to the blown bitumen in leachability and flash point, but inferior in the increase of volume by irradiation. Since the volume increase is not large, the distillation bitumen is satisfactory for the bituminization of the evaporator concentrate from a fuel reprocessing plant. (Mori, K.)

Investigation and analytical results of bituminized products in drums at filing room

International Nuclear Information System (INIS)

Shibata, Atsuhiro; Kato, Yoshiyuki; Sano, Yuichi; Kitajima, Takafumi; Fujita, Hideto

1999-09-01

This report describes the results of investigation of the bituminized products in drums, liquid waste in the receiving tank V21 and the bituminized mixture in the extruder. The investigation of the products in drums showed most of the unburned products filled after 28B had abnormality, such as hardened surfaces, caves and porous brittle products. The particle sizes of the salt fixed in bituminized products depended neither on batch number nor on feed rate. It indicates the fining of the salt particle caused by the decreased feed rate did not occur. The measured concentrations of metals and anions in the bituminized products showed no abnormality. The catalytic content was not recognized in the products. The infrared absorption spectra obtained with the bituminized products show the oxidation at the incident occurred without oxygen. There was no organic phase on the surface of liquid waste in V21. Chemical analysis and thermal analysis on the precipitate in V21 showed no abnormality. Concentration of sodium nitrate/nitrite in the mixture collected from the extruder was lower than normal products. These results show no chemical activation of the bituminized products. It can be concluded that the chemical characteristics of the products had little abnormality even around the incident. (author)

Bituminous sands : tax issues

International Nuclear Information System (INIS)

Patel, B.

2004-01-01

This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs

Présentation du dossier

Directory of Open Access Journals (Sweden)

2007-02-01

Full Text Available Les textes rassemblés dans ce dossier proviennent de la première Journée d’étude organisée par le groupe COnTEXTES, le 28 mars 2006 à l’Université de Liège. Le choix d’aborder une telle problématique a été guidé par le constat d’un décalage générationnel : tandis que la critique idéologique a mobilisé la plupart des consciences théoriques attentives aux forces sociales qui traversent le littéraire (Louis Althusser, Marc Angenot, Philippe Hamon, parmi d’autres, le concept d’idéologie semble a...

Optimization of the encapsulation process of bituminized radioactive wastes; Otimização do processo de encapsulamento do rejeito radioativo betuminizado

Energy Technology Data Exchange (ETDEWEB)

Silva, Jarine E.C.; Tello, Clédola C.O., E-mail: jarine.silva@cdtn.br, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEC-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The objective of this paper is to propose alternatives for the deposition of bituminized waste in metallic packages coated with a cementitious matrix for surface repository, aiming to meet the standards criteria and increasing the integrity of the metallic packaging during the planned storage time, transportation and disposal. For this purpose, tests will be carried out to evaluate cement pastes and mortar with cementitious additives, aiming at the durability and reduction of pores. Leaching tests with different thicknesses will also be carried out, where optimization of the encapsulation can meet safety, durability and economy standards for the repository, as well as practices that contribute to reduce environmental impacts and the economic burden imposed on future generations.

Influence of radiation on tar fraction of the bituminous oil

International Nuclear Information System (INIS)

Mustafayev, I.I.; Guliyeva, N.G.; Ibadov, N.E.; Melikova, S.Z.

2014-01-01

Full text : The chromato-masspectrometric and IR-spectrometric copic studies of bituminous oil samples irradiated in air and in vacuum are conducted. In the IR spectra of the gamma-irradiated samples, the optical density of some groups has been determined. It can be assumed that as a result of irradiation of the samples both in air and in vacuum, occurs a decrease of optical density both in aliphatic groups and the double bonds. The 27 individual components of initial and irradiated bituminous oil samples identified by mass-spectrometry. The high radiation stability of bituminous oils allows the use of it as a raw material for water proofing material, applied in terms of radiation influence

Bituminization of radioactive wastes at the Nuclear Research Center Karlsruhe

International Nuclear Information System (INIS)

Hild, W.; Kluger, W.; Krause, H.

1976-05-01

A summary is given of the main operational experience gained at the Nuclear Research Center Karlsruhe in 4 years operation of the bituminization plant for evaporator concentrates from low- and medium level wastes. At the same time some of the essential results are compiled that have been obtained in the R + D activities on bituminization. (orig.) [de

Teaching Dossier Documents: A Comparison of Importance by Major Stakeholders

Science.gov (United States)

Burnap, Charles A.; Kohut, Gary F.; Yon, Maria G.

2010-01-01

Most institutions of higher education require evidence of effective teaching as part of the review process for reappointment and for tenure/promotion. This study examines the relative importance of various documents placed in the teaching section of the dossier as rated by pre-tenured faculty members and review committee members. Results indicate…

Rotary drum for distilling bituminous material

Energy Technology Data Exchange (ETDEWEB)

1921-11-02

A rotary drum with insert tubes for distilling bituminous materials, like mineral coal, brown coal, wood, peat, and oil-shale, is characterized in that the insert tube is heated also by superheated steam introduced into the drum.

Behaviour of bituminized radioactive wastes under irradiation

International Nuclear Information System (INIS)

Camaro, S.; Gilardi, T.; Vistoli, P.P.

2000-01-01

Studies are carried out by the CEA in order to predict the behaviour of bituminized radioactive wastes under self irradiation. Bitumen radiolysis produces gas (mainly H 2 ) which diffuses in the organic matrix. If the hydrogen yield is higher than the diffusion flux through the free surface, hydrogen concentration increases and exceeds its solubility in bitumen. Beyond saturation, bubbles are formed and gas is also evacuated by bubbles drift. The aim of these studies is to evaluate the evacuation capacity of radiolytic gas produced in function of initial bituminized wasteform characteristics. A model was developed to achieve this purpose, by calculating the evolution of bubbles population considering all elementary mechanisms of gas evacuation. (authors)

Technological research of bituminization of model concentrates of radioactive wastes

International Nuclear Information System (INIS)

Breza, M.; Timulak, J.; Krejci, F.; Pekar, A.; Krajc, T.; Hladky, E.

1986-01-01

In the years 1981-1984 research was carried out of bituminization technology on model concentrates whose physical and chemical composition approximated that of radioactive concentrates from WWER-440 type nuclear power plants. The bitumen emulsion Silembit EAS-60 was used for bituminization. The process of bituminization took place at a temperature of approximately 180 degC in a rotary film evaporator into which was proportioned both the model concentrate and the bitumen emulsion heated to a temperature of 50 to 60 degC. All basic technical parameters of the process were controlled on an hourly basis. The experiments demonstrated the following technological conditions of bituminization: pressure of heating steam must be maintained within 0.85 and 0.95 MPa; optimal output of the evaporator (type FRO-2 S) is 100 to 120 kg of evaporated water/h; concentrates with a borate content must be heated to a temperature of 80 to 90 degC prior to their introduction into the evaporator; the pH value of the concentrates must be adjusted such as to be within the range of 11.0 to 11.5 or 7.0 to 8.0; the concentrate and the bitumen emulsion must be proportioned evenly; the optimal speed of the rotor is 500 r.p.m.; the load of the rotor must be monitored continuously because it indicates changes in the flow values of the bitumen composition. The experience gained was used in the operation of the pilot plant bituminization line for actual concentrates from the V-1 nuclear power plant. (A.K.)

Process of recovering bituminous materials

Energy Technology Data Exchange (ETDEWEB)

1920-08-22

A modification of the process covered by German Patent 389,393 for recovering bituminous materials from oil shale by extraction is disclosed consisting, in place of or besides wood spirit oil, of acetone oil, suitably of boiling point 80 to 130/sup 0/C, being used as the extraction medium.

Method of recovering oils, etc. , from bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1921-05-23

In the low-temperature distillation of bituminous shales or similar bituminous materials with high ash content for recovery of oil etc., steam or inert gases are introduced from outside through gas taps arranged in a circle in the retort. By the method used steam is introduced simultaneously in levels higher and lower than the one in which the gaseous and vaporized products are removed from the shale material and in such a manner that the zone of oil formation chiefly will be between the two places mentioned where vapors or steam are introduced into the retort. The patent has one additional claim.

Influence of the ionizing radiation on bituminous oil

International Nuclear Information System (INIS)

Aliyeva-Chichek, S.N; Guliyeva, S.; Aliyev, S.; Ahmedbekova, N. Ibadov.

2012-01-01

Full text : Bituminous oil is suitable for the production of road bitumen, lubricant oils, and energy fuel. In their structure, there is found an increased concentration of valuable metals (vanadium, nickel, etc.). The radiation-chemical transformations of bituminous oil, as well as the influence of an ionizing radiation on radiating stability of oil were investigated. Investigated oil was taken from Binagadi deposits from a depth in excess of 100 m.The source of ionizing radiation was used the isotope γ radiation 20 60 Ca MRX - γ 30 . The dose rate of the source of radiation is 0, 49 Gy/s, at the absorbed doses of 34,5-216 kGy. Methods of IR-Spectroscopy with an application of Spectrometer M-80 were used in the determination of the structural-group componential composition. Gas products were analyzed with the method of gas chromatography. Liquid products were identified by mass-spectrometer methods. The kinetics of the formations of gases was investigated by the radiolysis of oil as one of the parameters of the radiating stability of the bituminous oil. Samples of oil were irradiated in a vacuum and air conditions. It was established that presence of oxygen in the system does not significantly influence the radiation-chemical yields of the gases. Because at the room temperature, radiation-chemical disintegration proceeds without the introduction of oxygen into the reaction. This means that the rate of regrouping and splitting in the polycondensed systems is greater than the rate of interaction of the active radiolysis particles with oxygen. The influence of γ - irradiation on the structural-group composition of bituminous oil was investigated. It is visible from the comparison of IR-spectra of initial and irradiated samples of oil in the presence of air and in a vacuum, that there is a decrease in the optical density as a result of irradiation both in the aliphatic groups -CH 2 , -CH 3 , and in the double chemical bonds C=C. This shows that formation of

Treating bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Ginet, J H

1921-03-09

Apparatus for the treatment of bituminous shales is described wherein a number of separate compartments are arranged in alignment and communicate with each other near the bottom thereof, each of the compartments being provided with outlets for the gases evolved therein, while agitators are arranged in each of the compartments, each agitator being composed of a number of shovels which sweep up the comminuted shale at their forward end and discharge it at their rearward end into the path of the next adjacent agitator.

Lutte contre le changement climatique et maîtrise de la demande d’énergie : introduction au dossier thématique

OpenAIRE

Aubrée, Loïc; Calvo-Mendieta, Iratxe

2017-01-01

Cet article constitue l’introduction du dossier thématique consacré à la lutte contre le changement climatique et la maîtrise de la demande d’énergie. Après un dossier de la Revue Développement Durable et Territoires, paru en décembre 2015 et en juillet 2016, abordant la question du climat sous l’angle de l’adaptation, les articles de ce dossier s’intéressent aux politiques, aux programmes et aux instruments qui contribuent à l’atténuation du changement climatique. L’objectif est la diminutio...

Dossier: management of nuclear wastes. Research, results

International Nuclear Information System (INIS)

Anon.

2001-01-01

The researches carried out since many years on nuclear wastes have led to two main ways of management: the long-term conditioning of radio-elements and their advanced separation. The French atomic energy commission (CEA) has chosen to take up also the transmutation challenge, a way to transform long-living radioactive wastes into short-living radioactive wastes or stable compounds. The transmutation programs are based both on simulation and experiments with a huge international collaboration. This dossier presents in a digest way the research activity carried out on nuclear wastes processing and management at the CEA. (J.S.)

Distilling oils and bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Hutz, H

1925-08-25

In the distillation of bituminous materials such as coal, brown coal, peat, or mineral and tar oils or tar, in the presence of hot neutral gases such as hydrogen, illuminating gas, or water-gas, sulfur dioxide is also fed into the above-mentioned materials or into the vapors evolved therefrom. By this treatment better products are obtained.

Influence of association of "EVA-NBR" on indirect tensile strength of modified bituminous concrete

Science.gov (United States)

Chinoun, M.; Soudani, K.; Haddadi, S.

2016-04-01

The aim of this work is to contribute to the improvement of the mechanical properties of bituminous concrete by modification of bituminous concrete. In this study, we present the results of the indirect tensile strength "ITS" of modified bituminous concrete by the combination of two modifiers, one is a plastomer EVA (Ethylene Vinyl Acetate) and the other is a industrial waste from the shoe soles grinding NBR (Nitrile Butadiene Rubber) as crumb rubber. To modify the bitumen a wet process was used. The results show that the modification of bitumen by EVA-NBR combination increases their resistance to the indirect traction "ITS" compared to the bituminous concrete control. The mixture of 5% [50% EVA+ 50% NBR] is given the best result among the other associations.

Bayesian cost-effectiveness analysis with the R package BCEA

CERN Document Server

Baio, Gianluca; Heath, Anna

2017-01-01

The book provides a description of the process of health economic evaluation and modelling for cost-effectiveness analysis, particularly from the perspective of a Bayesian statistical approach. Some relevant theory and introductory concepts are presented using practical examples and two running case studies. The book also describes in detail how to perform health economic evaluations using the R package BCEA (Bayesian Cost-Effectiveness Analysis). BCEA can be used to post-process the results of a Bayesian cost-effectiveness model and perform advanced analyses producing standardised and highly customisable outputs. It presents all the features of the package, including its many functions and their practical application, as well as its user-friendly web interface. The book is a valuable resource for statisticians and practitioners working in the field of health economics wanting to simplify and standardise their workflow, for example in the preparation of dossiers in support of marketing authorisation, or acade...

Apparatus for distillation of bituminous material

Energy Technology Data Exchange (ETDEWEB)

Carthaus, E; von Rittersberg, K; Abraham, A

1917-05-03

Apparatus for dry distillation of bituminous material, such as oil shale and brown coal with simultaneous fractional separation of the distillate, consists in the fact, that the domed water-cooled condenser, arranged above the conveyer carrying it, is divided by double vertical partitions in the chamber.

Nagra technical report 14-02, geological basics - Dossier V - Hydro-geological conditions; SGT Etappe 2: Vorschlag weiter zu untersuchender geologischer Standortgebiete mit zugehörigen Standortarealen für die Oberflächenanlage -- Geologische Grundlagen -- Dossier V -- Hydrogeologische Verhältnisse

Energy Technology Data Exchange (ETDEWEB)

Traber, D.; Gautschi, A.; Marschall, P.; Becker, J. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Waber, N. [Institut of Geological Sciences, University of Berne, Berne (Switzerland)

2014-12-15

This dossier is the fifth of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. Dossier V looks at hydro-geological considerations in North-Western Switzerland. Rock layers in the region and their hydrological properties are examined. Ground-water and deeper lying aquifers in the various rock formations are discussed. The specific hydrology in the proposed areas for nuclear waste depositories is looked at, including infiltration and exfiltration zones and gradients.

Identification of aggregates for Tennessee bituminous surface courses

Science.gov (United States)

Sauter, Heather Jean

Tennessee road construction is a major venue for federal and state spending. Tax dollars each year go to the maintenance and construction of roads. One aspect of highway construction that affects the public is the safety of its state roads. There are many factors that affect the safety of a given road. One factor that was focused on in this research was the polish resistance capabilities of aggregates. Several pre-evaluation methods have been used in the laboratory to predict what will happen in a field situation. A new pre-evaluation method was invented that utilized AASHTO T 304 procedure upscaled to accommodate surface bituminous aggregates. This new method, called the Tennessee Terminal Textural Condition Method (T3CM), was approved by Tennessee Department of Transportation to be used as a pre-evaluation method on bituminous surface courses. It was proven to be operator insensitive, repeatable, and an accurate indication of particle shape and texture. Further research was needed to correlate pre-evaluation methods to the current field method, ASTM E 274-85 Locked Wheel Skid Trailer. In this research, twenty-five in-place bituminous projects and eight source evaluations were investigated. The information gathered would further validate the T3CM and find the pre-evaluation method that best predicted the field method. In addition, new sources of aggregates for bituminous surface courses were revealed. The results of this research have shown T3CM to be highly repeatable with an overall coefficient of variation of 0.26% for an eight sample repeatability test. It was the best correlated pre-evaluation method with the locked wheel skid trailer method giving an R2 value of 0.3946 and a Pearson coefficient of 0.710. Being able to predict field performance of aggregates prior to construction is a powerful tool capable of saving time, money, labor, and possibly lives.

Solidification of radioactive wastes by bituminization technology. II

International Nuclear Information System (INIS)

Stuchlik, S.; Brzobohaty, J.

1985-01-01

The bituminization line consists of a rotor film evaporator, a condenser, reserve tanks of bitumen emulsion and model concentrates, a roller train, a vapour concentrate tank, a control console, a bitumen emulsion pump, a model concentrates pump, and a tank for model concentrate preparation. Anion-active emulsion Silembit S-60 produced by Paramo Pardubice was chosen as the bitumen emulsion. A block diagram is given of the experimental bituminization line and its processing is described of model nonactive concentrates whose composition corresponds to that of actual wastes from the V-1 nuclear power plant. Successful tests of the line showed that it could be used for the disposal of radioactive wastes. (E.S.)

Leaching behavior of a simulated bituminized radioactive waste form under deep geological conditions

International Nuclear Information System (INIS)

Nakayama, Shinichi; Iida, Yoshihisa; Nagano, Tetsushi; Akimoto, Toshiyuki

2003-01-01

The leaching behavior of a simulated bituminized waste form was studied to acquire data for the performance assessment of the geologic disposal of bituminized radioactive waste. Laboratory-scale leaching tests were performed for radioactive and non-radioactive waste specimens simulating bituminized waste of a French reprocessing company, COGEMA. The simulated waste was contacted with deionized water, an alkaline solution (0.03-mol/l KOH), and a saline solution (0.5-mol/l KCl) under atmospheric and anoxic conditions. The concentrations of Na, Ba, Cs, Sr, Np, Pu, NO 3 , SO 4 and I in the leachates were determined. Swelling of the bituminized waste progressed in deionized water and KOH. The release of the soluble components, Na and Cs, was enhanced by the swelling, and considered to be diffusion-controlled in the swelled layers of the specimens. The release of sparingly soluble components such as Ba and Np was solubility-limited in addition to the progression of leaching. Neptunium, a redox-sensitive element, showed a distinct difference in release between anoxic and atmospheric conditions. The elemental release from the bituminized waste specimens leached in the KCl was very low, which is likely due to the suppression of swelling of the specimens at high ionic strength. (author)

Results of exploitation of a pilot-plant installation for bituminization of radioactive sludges

International Nuclear Information System (INIS)

Golinski, M.; Ksiazak, Z.; Surala, J.; Dziubecki, R.

1974-01-01

Results are discussed of exploitation of a pilot-plant installation for bituminization of radioactive sludges of an efficiency of 25 l/h. In a time period of 20 month 120 cycles were carried out in which 60 m 3 of 2-4% sludges from treatment of low-level waste by the phosphate-ferrocyanide method were solidified. The P-60 asphalt was used for bituminization. The bituminization products contained 5-13.5% of mineral substances. Their activity was in the range 5 x 10 -4 - 5 x 10 -3 μCi/g for alpha emitters and 1.2 - 3.8 x 10 -2 μCi/g for beta emitters. (author)

Waste bituminization system in CDTN

International Nuclear Information System (INIS)

Guzella, M.F.R.; Miaw, S.T.W.

1990-01-01

Experimental works on low level waste bituminization have been developed at the Radioactive Waste Treatment Division of CDTN. A small scale bitumen extruder (1 kg/h) similar to the Angra II one is in operation. Some types of Brazilian bitumen have been selected and incorporation experiments with different types of waste were carried out; the operating conditions have been defined and the final product properties investigated. (author) [pt

A Critical Analysis of the Environmental Dossiers from the OECD Sponsorship Programme for the Testing of Manufactured Nanomaterials

DEFF Research Database (Denmark)

Hansen, Steffen Foss; Hjorth, Rune; Skjolding, Lars Michael

2017-01-01

In 2015, the OECD finally published the findings of its seven year testing programme for manufactured nanomaterials. Here, we present the first in-depth analysis of the published OECD dossiers with regards to data on physical and chemical properties, environmental fate and ecotoxicology. Each...... prior, during and/or at the end of the study. We find that the information in the dossiers present an incomplete portfolio of nanomaterial ecotoxicological evaluations that are difficult to draw substantive conclusions from and that most of the studies were not designed to investigate the validity...

Effect of Mixing Process on Polypropylene Modified Bituminous Concrete Mix Properties

OpenAIRE

Noor Zainab Habib; Ibrahim Kamaruddin; Madzalan Napiah; Isa Mohd Tan

2011-01-01

This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely cont...

Process of treating bituminous material, etc

Energy Technology Data Exchange (ETDEWEB)

Pfeiffer, J P

1939-09-28

Process for the preparation of bituminous materials or substances which they contain and of better properties, especially those adhering and subdividing in the presence of water or moisture, in that these materials are mixed with amounts of sulfuric acid esters or arylsufonic aicd esters of low primary aliphatic alcohols or with materials from which these esters can be formed.

Apparatus for carbonizing bituminous substances, etc

Energy Technology Data Exchange (ETDEWEB)

Meguin, A G

1921-06-24

A process is disclosed of carbonizing bituminous substances such as coal, or shale, at a low temperature, the distinguishing feature being that during the gas-distillation period, the material is subjected to centrifugal action in a rotary drum or retort is distributed over the whole circumference of the drum and is at the same time compressed.

Rotary retort for carbonizing bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Meguin, A G; Muller, W

1920-09-05

A process of carbonizing bituminous materials, such as coal and oil shale at a low temperature in a rotary retort with simultaneous compressing the material especially of the semicoke formed that is characterized in that the material during the distillation through rapid rotation of the retort is exposed to the action of centrifugal force and thereby it is compressed.

The problem of extracting oil from bituminous rock

Energy Technology Data Exchange (ETDEWEB)

Liatifov, A.I.; Bagirov, M.K.; Shirinov, S.G.; Sokov, U.I.; Zhirnov, E.I.

1982-01-01

Results are given from experimental laboratory research on flushing bituminous sandstones using diesel or oil alkaline by-products as the flushing agent and a sodium silicate solution as the desensitization initiator for the rock.

Properties of bituminization product from Olkiluoto power plant

International Nuclear Information System (INIS)

Valkiainen, M.; Vuorinen, U.

1985-09-01

In Finland, disposal into repositories excavated into bedrock on the present power plant sites is considered to be the most feasible alternative for the low- and intermediate level wastes. The Nuclear Waste Commission of the Finnish power companies has sponsored mainly experimental research work on long-term properties of bituminized ion exchange resin performed in the Reactor Laboratory of the Technical Research Centre of Finland since 1981. This report presents results on follow-up measurements of the leach tests started in 1981 and results on new leach tests with cement equilibrated water. Swelling of the bituminization product caused by water uptake is considered important. Both unrestricted and restricted swelling measurements were performed and are reported here. In addition to leaching and swelling also radiolytic gas generation and pH-changes of the leachant are discussed

Crumb Rubber in cold recycled bituminous mixes

DEFF Research Database (Denmark)

Dondi, Giulio; Tataranni, Piergiorgio; Pettinari, Matteo

2014-01-01

Today recycling is one of the most innovative and interesting techniques for the rehabilitation of destressed road pavements. In recent years the increased interest in this process, has led to the development of various alternative methods for the recovery and the reuse of road bituminous materials...

Evaluating Self Healing Capability of Bituminous Mastics

NARCIS (Netherlands)

Qiu, J.; Van de Ven, M.; Wu, S.; Yu, J.; Molenaar, A.

2012-01-01

The self-healing capability of bituminous materials has been known for many years. Researches were mostly focused on the self healing behaviour during load repetitions. The tests are either time consuming and/or complex. In this paper, a simple self healing test procedure is presented combining the

Recovery of asphalt from bituminous minerals

Energy Technology Data Exchange (ETDEWEB)

Jossinet, J

1881-12-31

A process is disclosed for the recovery of asphalt from bituminous minerals, consisting in that the mineral is extracted with mineral oil, which is recovered by distilling the raw asphalt and distilling the solution to obtain on the one hand the liquid oil contained in the raw asphalt for use in the extraction and on the other hand distilled asphalt.

Design and verification of bituminous mixtures with the increased content of reclaimed asphalt pavement

Science.gov (United States)

Bańkowski, Wojciech; Król, Jan; Gałązka, Karol; Liphardt, Adam; Horodecka, Renata

2018-05-01

Recycling of bituminous pavements is an issue increasingly being discussed in Poland. The analysis of domestic and foreign experience indicates a need to develop this technology in our country, in particular the hot feeding and production technologies. Various steps are being taken in this direction, including research projects. One of them is the InnGA project entitled: “Reclaimed asphalt pavement: Innovative technology of bituminous mixtures using material from reclaimed asphalt pavement”. The paper presents the results of research involving the design of bituminous mixtures in accordance with the required properties and in excess of the content of reclaimed asphalt permitted by the technical guidelines. It presents selected bituminous mixtures with the content of RAP of up to 50% and the results of tests from verification of industrial production of those mixtures. The article discusses the details of the design process of mixtures with a high content of reclaimed asphalt, the carried out production tests and discusses the results of tests under the verification of industrial production. Testing included basic tests according to the Polish technical requirements of WT- 2 and the extended functional testing. The conducted tests and analyses helped to determine the usefulness of the developed bituminous mixtures for use in experimental sections and confirmed the possibility of using an increased amount of reclaimed asphalt up to 50% in mixtures intended for construction of national roads.

Inductive bituminous mortar with steel and aluminum fibers

NARCIS (Netherlands)

Pavlatos, N.; Apostolidis, P.; Scarpas, Athanasios; Liu, X.; van de Ven, M.F.C.

2018-01-01

This research presents the implementation of a finite element model analysis for assessing the potential of utilizing alternative fibers for the development of inductive bituminous mixes with lower total weight, higher resistance against corrosion, and sufficient induction heating efficiency.

Losses due to weather phenomena in the bituminous concrete construction industry in Wisconsin

Science.gov (United States)

Kuhn, H. A. J.

1973-01-01

The losses (costs) due to weather phenomena as they affect the bituminous concrete industry in Wisconsin were studied. The bituminous concrete industry's response to precipitation, in the form of rain, is identified through the use of a model, albeit crude, which identifies a typical industry decision-response mechanism. Using this mechanism, historical weather data and 1969 construction activity, dollar losses resulting from rain occurrences were developed.

Process of producing fuels from slates or bituminous shales. [distillation at incandescent heat

Energy Technology Data Exchange (ETDEWEB)

Huppenbauer, M

1902-07-31

A process of producing a fuel from slates or bituminous shales by saturating or impregnating them after preliminary distillation with the vapors of tars, resins, oils, etc., is given. The process is characterized by the bituminous shale being submitted in the form of fragments to distillation at incandescent heat to make the shale porous and able to absorb the vapors of the substances already mentioned.

Nagra technical report 14-02, geological basics - Dossier IV - Information on geo-mechanics; SGT Etappe 2: Vorschlag weiter zu untersuchender geologischer Standortgebiete mit zugehörigen Standortarealen für die Oberflächenanlage -- Geologische Grundlagen -- Dossier IV -- Geomechanische Unterlagen

Energy Technology Data Exchange (ETDEWEB)

Marschall, P.; Giger, S.

2014-12-15

This dossier is the fourth of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. This Dossier IV considers the documentation on geo-mechanical aspects that is available. Rock-stress conditions are looked at as are the methods and instrumentation used to establish them. The results of local analyses are presented and discussed, as are the magnitudes and long-term stability of such stress conditions. The geo-mechanical properties of Opalinus Clay as a host rock for a repository are discussed. Mountain-building models and coupled hydro-mechanical processes are also discussed.

Tips for Constructing a Promotion and Tenure Dossier that Documents Engaged Scholarship Endeavors

Science.gov (United States)

Franz, Nancy K.

2011-01-01

The growth of the community engagement movement in higher education over the past 2 decades has resulted in more faculty member interest and practice in engaged scholarship. As more institutions value this work, faculty members are looking for ways to enhance the effectiveness of their engaged scholarship dossiers for promotion and tenure. This…

Development of the ''measurement and sorting'' device for bituminized waste drums at Cogema Marcoule

International Nuclear Information System (INIS)

Chabalier, B.; Artaud, J.L.; Perot, B.; Passard, C.; Romeyer Dherbey, J.; Raoux, A.; Misraki, J.

2000-01-01

This programme is included in the scope of a specific task to retrieve bituminized waste drums stored on the Marcoule site. The objective is to define a non-destructive nuclear measurement facility that makes it possible to: - sort the packages stored on the site according to the radiological acceptance criteria for the waste packages in the surface storage facility, - establish the β and α activities of the packages to be stored in the surface storage facility, - estimate the activity of the packages that will be stored in the ''Entreposage Intermediaire Polyvalent'' (multiple purpose intermediate storage) built on the Marcoule site. A measurement facility, with measurement times compatible with the industrial flow of retrieval of the waste drums was studied, developed and will be validated. It features gamma spectrometry measurements and neutron measurement devices, associated to an imaging device by photonic transmission and an expert system. Studies associated to the definition of this facility mainly concern: - the imaging station: it enables to know up to what height the packages are filled, the actual density of the matrix, and to detect lacks of homogeneity. These data are required for a correct analysis of the neutron or gamma measurements and to minimise uncertainties, - the interpretation of active neutron measurement signals: a simultaneous detection of the prompt and delayed neutrons makes it possible to differentiate the masses of U-235 and of Pu-239 present in the packages, - the reduction of the detection limits: to that end, an ''asti-Compton'' detector was defined providing a gain on the detection limits at low energies according to the type of GeHP semi-conductor detector. - the expert system which performs the interpretation and coupling of measured data with data coming from the waste production files in order to determine the activity of the β γ, pure β and α radionuclides at 300 years. The validation program that will be conducted on a

Apparatus for treating bituminous shale

Energy Technology Data Exchange (ETDEWEB)

1942-11-24

A method is given of transforming finely crushed bituminous shale, for instance of maximum particle size of about 5 mm, into balls, nodules, or similar shapes, in which the shale to be treated is passed in the form of lumps through a rotary drum. The finely crushed shale with a higher content of moisture is brought into contact with finely crushed shale of a lower content of moisture, and thereby serves as kernel material during the formation of the nodules or similar shapes.

8th RILEM International Symposium on Testing and Characterization of Sustainable and Innovative Bituminous Materials

CERN Document Server

Partl, Manfred

2016-01-01

This work presents the results of RILEM TC 237-SIB (Testing and characterization of sustainable innovative bituminous materials and systems). The papers have been selected for publication after a rigorous peer review process and will be an invaluable source to outline and clarify the main directions of present and future research and standardization for bituminous materials and pavements. The following topics are covered: - Characterization of binder-aggregate interaction - Innovative testing of bituminous binders, additives and modifiers - Durability and aging of asphalt pavements - Mixture design and compaction analysis - Environmentally sustainable materials and technologies - Advances in laboratory characterization of bituminous materials - Modeling of road materials and pavement performance prediction - Field measurement and in-situ characterization - Innovative materials for reinforcement and interlayer systems - Cracking and damage characterization of asphalt pavements - Rec...

Biodegradation of bituminous products from processing liquid radioactive wastes

International Nuclear Information System (INIS)

Tibensky, L.; Krejci, F.; Hladky, E.; Halama, D.

1988-01-01

One of the possible ways of disturbing the stability of bituminous products from liquid radioactive waste processing, is biodegradation caused by common microorganisms. Pseudomonas bacteria and a Bacillus cereus culture were selected for experimental study of cultivation of microorganisms. Experiments with mixed cultures were also performed. Pitches, ajatin and imidazoline were used as inhibitors. The thin layer and the emulsion methods were used in assessing biological corrosion. The results of the experiments are discussed with respect to the dependence of bacterial growth on bitumen biodegradation, the effect of pH on bitumen degradation and the effect of inhibitors on bitumen biodegradation. The salts contained in bituminous products were not found to significantly affect the rate of destruction. The degree of degradation was found to mainly depend on the bitumen, its chemical composition, and on the conditions of storage. It was also found that inhibitor additions in some cases modified the properties of the matrix such that it became more liquid. The coefficient of extractibility thus increased of matrix salts. The recultivation of bacteria on a full-value medium resulted in the loss of the inhibitory effect. In some cases, the inhibitor even stimulated the growth of microorganisms. The use of inhibitors in an effort to achieve biostability of bituminous products thus did not solve the problem. (Z.M.). 2 tabs., 9 refs

Drivers of Competitiveness and Strategies for Economic ...

International Development Research Centre (IDRC) Digital Library (Canada)

... Korea's package for enhancing FTA utilization. Téléchargez le PDF. Dossiers. SME loan defaults in Bangladesh. Téléchargez le PDF. Dossiers. Moving freely? : labour mobility in ASEAN. Téléchargez le PDF. Dossiers. Kazakhstan's membership of the Eurasian Customs Union : implications for trade and WTO accession.

Aqueous radioactive waste bituminization

International Nuclear Information System (INIS)

Williamson, A.S.

1980-08-01

The bituminzation of decontamination and ion exchange resin stripping wastes with four grades of asphalt was investigated to determine the effects of asphalt type on the properties of the final products. All waste forms deformed readily under light loads indicating they would flow if not restrained. It was observed in all cases that product leaching rates increased as the hardness of the asphalt used to treat the waste increased. If bituminization is adopted for any Ontario Hydro aqueous radioactive wastes they should be treated with soft asphalt to obtain optimum leaching resistance and mechanical stability during interim storage should be provided by a corrosion resistant container

Pressure analysis in ventilation ducts at bituminization facility

International Nuclear Information System (INIS)

Kikuchi, Naoki; Iimura, Masato; Takahashi, Yuki; Omori, Eiichi; Yamanouchi, Takamichi

1997-09-01

Pressure analysis in cell ventilation ducts at bituminization facility where the fire and explosion accident occured was carried out. This report also describes the results of bench mark calculations for computer code EVENT84 which was used for the accident analysis. The bench mark calculations were performed by comparing the analytical results by EVENT84 code with the experimental data of safety demonstration tests of ventilation system which were carried out by JAERI. We confirmed the applicability of EVENT84 code with the conservative results. The pressure analysis in cell ventilation ducts at bituminization facility were performed by comparing the analytical results of duct pressure by EVENT84 code with the yield stress of destroyed ducts by explosion, in order to estimate the scale of explosion. As a result, we could not explain the damage of ducts quantitatively, but we found the local pressure peaks analytically in downstream ducts where the serious damages were observed. (author)

Concentration of viruses from water on bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Lakhe, S.B.; Parhad, N.M.

1988-05-01

The potential of bituminous coal for adsorption of viruses, using poliovirus as a model, was investigated. Influence of pH of water on the adsorption of viruses on a coal bed with and without addition of cation (Al/sup 3 +/) indicated that poliovirus could be adsorbed efficiently at pH 5 in presence of AlCl/sub 3/ at a concentration of 0.0005 M. studies on the effect of different concentrations of monovalent, divalent and trivalent cations showed that the trivalent cation was more effective and was required at a lower concentration than other cations tested. A coal bed of 1.5 g could adsorb as high as 204,000 PFU from water based on the absence of virus in the filtrate. Total organic carbon content of the water did not interfere in virus adsorption to coal. The results obtained indicated that a bituminous coal bed could be used as one of the methods for efficient concentration of viruses from water. 31 refs., 8 tabs.

Use of additives to improve the capacity of bituminous mixtures to be heated by means of microwaves

International Nuclear Information System (INIS)

Gallego, J.; Val, M.A. del; Contreras, V.; Páez, A.

2017-01-01

This study examines the potential of adding electric arc furnace slag to bituminous mixtures to be heated by microwaves. The susceptibility of bituminous mixtures to microwave energy is limited and so, in order to improve the energy performance of the heating process, it is necessary to incorporate additives or components to the mixture so as to improve the capacity for microwave heating. The article presents the results of adding various components, (steel wool, scrap tire wire, silicon carbide, iron filings) and an alternative aggregate: electric arc furnace slag. According to the results obtained in the laboratory, slag addition of at least 5% by weight of the bituminous mixture represents the best option for both technical and economic reasons. The results may promote the valorization of this steel industry residue in bituminous mixtures by improving microwave heating response. [es

Method of distillation of sulfurous bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Hallback, A J.S.; Bergh, S V

1918-04-22

A method of distillation of sulfur-containing bituminous shales is characterized by passing the hot sulfur-containing and oil-containing gases and vapors formed during the distillation through burned shale containing iron oxide, so that when these gases and vapors are thereafter cooled they will be, as far as possible, free from sulfur compounds. The patent contains six more claims.

Comparison of the performances of several modified bituminous mix formulas

Science.gov (United States)

Saoula, Samia; Haddadi, Smail; Mokhtar, Khedidja Ait

2012-09-01

The mechanical behaviour of several formulas of bituminous concrete containing polymer (HDPE), polymer-bitumens (EVA) and waste of sole of shoes (containing copolymer butadiene-styrene-SBR noted DSBR and ethylene and vinyl acetate-EVA noted DEVA) were studied. The aim of this work is to improvement of the poor mechanicals performances of a bituminous concrete formula (0/14) which isn't conforming to the Algerian standards. Also, the mechanical tests showed that the permanent deformations and the indirect tensile strength at the temperatures of service resistances are improved. At high-temperature service, formulas of asphalt bitumen-EVA most resistant against the average temperature in service, it mixes made with waste are best resistant. All the formulas have a good behaviour with water.

Quality assurance program : bituminous concrete and central mix aggregates.

Science.gov (United States)

1980-01-01

This report presents the results of a pilot quality assurance program initiated in the Richmond District in 1978. Under this program the producer's control tests are used for the acceptance of central mix aggregate and bituminous concrete and the Dep...

Rutting performance of cold bituminous emulsion mixtures

Science.gov (United States)

Arshad, Ahmad Kamil; Ali, Noor Azilatom; Shaffie, Ekarizan; Hashim, Wardati; Rahman, Zanariah Abd

2017-10-01

Cold Bituminous Emulsion Mixture (CBEM) is an environmentally friendly alternative to hot mix asphalt (HMA) for road surfacing, due to its low energy requirements. However, CBEM has generally been perceived to be less superior in performance, compared to HMA. This paper details a laboratory study on the rutting performance of CBEM. The main objective of this study is to determine the Marshall properties of CBEM and to evaluate the rutting performance. The effect of cement in CBEM was also evaluated in this study. The specimens were prepared using Marshall Mix Design Method and rutting performance was evaluated using the Asphalt Pavement Analyzer (APA). Marshall Properties were analysed to confirm compliance with the PWD Malaysia's specification requirements. The rutting performance for specimens with cement was also found to perform better than specimens without cement. It can be concluded that Cold Bituminous Emulsion Mixtures (CBEM) with cement is a viable alternative to Hot Mix Asphalt (HMA) as their Marshall Properties and performance obtained from this study meets the requirements of the specifications. It is recommended that further study be conducted on CBEM for other performance criteria such as moisture susceptibility and fatigue.

FY 1991 report on the bituminous coal liquefaction section; 1991 nendo rekiseitan ekikabukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

The paper reported activities of the bituminous coal liquefaction section in FY 1991. In the 1st bituminous coal liquefaction section meeting, report/discussion were made on the outline of the plan on the FY 1991 research using pilot plant and the support study of pilot plant. In the 2nd section meeting, report was made on 'How the development of coal liquefaction technology should be in the 21st century,' a report made by the joint section of bituminous coal/brown coal liquefaction. In the 3rd section meeting, report/discussion were made on the state of progress of the FY 1991 R and D and results. In the study using the bituminous coal liquefaction pilot plant, report was made on the outline of construction of a 150t/d pilot plant, study on the acquisition of material balance, analytical study of the data on liquefaction tower, testing survey on properties of coal slurry, and testing survey on slurry preheating furnace. In the support study of pilot plant, report was made on the study using 1t/d PUS, study on the development of the optimum coal refining technology and improvement in the distillate distribution, study of conditions for coal liquefaction and study of solvent hydrogenation catalyst. (NEDO)

Pre-treatment of bituminized NPP wastes for disposal in near-surface repository

Energy Technology Data Exchange (ETDEWEB)

Vieira, Vanessa Mota; Tello, Clédola Cássia Oliveira de, E-mail: vanessamotavieira@gmail.com, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The implementation of the national repository is an important technical requirement, and a legal requirement for the entry into operation of the nuclear power plant Angra 3. The Brazilian repository is being planned to be a near-surface one. In Brazil the low and intermediate level radioactive wastes are immobilized using cement and bitumen for Angra 1 and Angra 2 NPP, respectively. The main problems due to the disposal of bituminized wastes in repositories are swelling of the waste products and their degradation in the long term. To accommodate the swelling of the bituminized wastes, the drums are filled up to 70 - 90% of their volume, which reduces the structural the repository stability and the disposal availability. Countries, which use bitumen in the solidification of NPP's radioactive waste and have near-surface repositories, need to immobilize this bituminized waste within other drums containing cement pastes or mortars to disposal them. This study aims to find solutions for the storage in surface repository of bituminized radioactive waste products, making them compatible with the acceptance criteria of cemented waste products. It was also performed a modeling with the results obtained in the leaching test using the ALT program and defined the transport model of the cesium leachate element and it was verified that in the early times the leaching was governed by the diffusion model and later by the partition model. The results obtained in this study can be used in the evaluation of performance of repositories. (author)

Pre-treatment of bituminized NPP wastes for disposal in near-surface repository

International Nuclear Information System (INIS)

Vieira, Vanessa Mota; Tello, Clédola Cássia Oliveira de

2017-01-01

The implementation of the national repository is an important technical requirement, and a legal requirement for the entry into operation of the nuclear power plant Angra 3. The Brazilian repository is being planned to be a near-surface one. In Brazil the low and intermediate level radioactive wastes are immobilized using cement and bitumen for Angra 1 and Angra 2 NPP, respectively. The main problems due to the disposal of bituminized wastes in repositories are swelling of the waste products and their degradation in the long term. To accommodate the swelling of the bituminized wastes, the drums are filled up to 70 - 90% of their volume, which reduces the structural the repository stability and the disposal availability. Countries, which use bitumen in the solidification of NPP's radioactive waste and have near-surface repositories, need to immobilize this bituminized waste within other drums containing cement pastes or mortars to disposal them. This study aims to find solutions for the storage in surface repository of bituminized radioactive waste products, making them compatible with the acceptance criteria of cemented waste products. It was also performed a modeling with the results obtained in the leaching test using the ALT program and defined the transport model of the cesium leachate element and it was verified that in the early times the leaching was governed by the diffusion model and later by the partition model. The results obtained in this study can be used in the evaluation of performance of repositories. (author)

Unexpectedly high uptake of palladium by bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Lakatos, J. [Research Lab. for Mining Chemistry, Hungarian Academy of Sciences, Miskolc-Egyetemvaros (Hungary); Brown, S.D.; Snape, C.E. [Univ. of Strathclyde, Dept. of Pure and Applied Chemistry, Glasgow (United Kingdom)

1997-12-31

The uptake of palladium as a conversion catalyst onto coals of different rank was investigated. Palladium fixation occurs by a different mode to that for alkaline earth and first row transition metals. Therefore, the dispersion of relatively high concentration of palladium by an ion sorption process is even possible for bituminous coals. (orig.)

MECHANICAL BEHAVIOR OF COLD BITUMINOUS MIXTURE UNDER EFFECTS OF STATIC AND REPEATED LOADS1

OpenAIRE

Tamyres Karla da Silva; Carlos Alexandre Braz de Carvalho; Geraldo Luciano de Oliveira Marques; Dario Cardoso de Lima; Taciano Oliveira da Silva; Carlos Cardoso Machado

2017-01-01

Abstract This paper presents the results of an experimental research aimed at analyzing the mechanical behavior of a cold bituminous mixture under effects of static and repeated loads. Initially, a Marshall mixture design was performed to determine the mixture design contents according to standard DNER (1994a). After obtaining the mixture design contents, nine bituminous specimens were molded and subjected to the following tests: resilient modulus, tensile strength by diametral compression, a...

Het digitale sport medisch dossier: zucht of zegen? [Digital Sport Medical Record: Sigh or a blessing?

NARCIS (Netherlands)

Stege, J.P.; Fleuren, M.A.H.; Knaap, E.T.W. van der; Stubbe, J.H.

2013-01-01

Sinds 2004 zijn er verschillende initiatieven ontplooid rondom de ontwikkeling van een digitaal Sport Medisch Dossier (SMD). Uit gesprekken met de Vereniging voor Sportgeneeskunde (VSG) blijkt dat er vooral problemen worden gesignaleerd met de ingebruikname van het digitale SMD. In het voorjaar van

Dossier: renewable energies for heat production; Dossier: energies renouvelables pour la production de chaleur

Energy Technology Data Exchange (ETDEWEB)

Anon.

2002-09-01

This dossier makes a state-of-the-art of today's applications of renewable energy sources in the residential, collective and tertiary sectors for the space heating and the hot water production. In France, three energy sources profit by a particularly favorable evolution: the solar thermal, the wood fuel and the geothermal energies. In these sectors, the offer of reliable and technically achieved appliances has been considerably widen thanks to the impulse of some French and German manufacturers. Part 1 - solar thermal: individual solar water heaters (monobloc, thermosyphon with separate tank, forced circulation systems, auxiliary heating systems); combined solar systems (direct heating floor, system with storage); collective solar systems for hot water production (receivers, efficiency, heat storage and transfer, auxiliary heating, decentralized systems); heating of open-air swimming pools; some attempts in air-conditioning; the warranty of results. Part 2 - wood fuels: domestic space heating (log boilers, installation rules, hydro-accumulation, automatic boilers); collective and tertiary wood-fueled heating plants (design of boiler plants, fuel supply, combustion chamber, smoke purification systems, ash removal, regulation system), fuels for automatic collective plants, design and installation rules. Part 3 - geothermal energy: different types (water-source and ground-source heat pumps, financial incentive). (J.S.)

Aerobic Biofilms Grown from Athabasca Watershed Sediments Are Inhibited by Increasing Concentrations of Bituminous Compounds

Science.gov (United States)

Lawrence, John R.; Sanschagrin, Sylvie; Roy, Julie L.; Swerhone, George D. W.; Korber, Darren R.; Greer, Charles W.

2013-01-01

Sediments from the Athabasca River and its tributaries naturally contain bitumen at various concentrations, but the impacts of this variation on the ecology of the river are unknown. Here, we used controlled rotating biofilm reactors in which we recirculated diluted sediments containing various concentrations of bituminous compounds taken from the Athabasca River and three tributaries. Biofilms exposed to sediments having low and high concentrations of bituminous compounds were compared. The latter were 29% thinner, had a different extracellular polysaccharide composition, 67% less bacterial biomass per μm2, 68% less cyanobacterial biomass per μm2, 64% less algal biomass per μm2, 13% fewer protozoa per cm2, were 21% less productive, and had a 33% reduced content in chlorophyll a per mm2 and a 20% reduction in the expression of photosynthetic genes, but they had a 23% increase in the expression of aromatic hydrocarbon degradation genes. Within the Bacteria, differences in community composition were also observed, with relatively more Alphaproteobacteria and Betaproteobacteria and less Cyanobacteria, Bacteroidetes, and Firmicutes in biofilms exposed to high concentrations of bituminous compounds. Altogether, our results suggest that biofilms that develop in the presence of higher concentrations of bituminous compounds are less productive and have lower biomass, linked to a decrease in the activities and abundance of photosynthetic organisms likely due to inhibitory effects. However, within this general inhibition, some specific microbial taxa and functional genes are stimulated because they are less sensitive to the inhibitory effects of bituminous compounds or can degrade and utilize some bitumen-associated compounds. PMID:24056457

Les dossiers de pensions des troupes coloniales et indigènes. La sous-série GR 13 Yf 

OpenAIRE

HEISER, Sandrine; Guillot, Hélène

2013-01-01

En avril 2011, le Service historique de la Défense (SHD) a débuté le classement des dossiers de pensions des troupes coloniales et des troupes indigènes pour la période 1850-1950. 14 000 premiers dossiers ont été inventoriés, sur un total de 24 000, l’objectif étant d’achevé le classement pour le centenaire de la Grande Guerre. L’opération comporte également une phase importante de reconditionnement permettant une communication immédiate et idéale aux lecteurs au gré des mises à jour régulièr...

Global market trade policy analysis for petroleum oils and oils obtained from bituminous minerals, crude

Directory of Open Access Journals (Sweden)

Bagheri, F.

2012-01-01

Full Text Available This article is based on surveying the custom tariffs imposed on the world export market of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. We obtained the data according to the most updated available data provided online by UNCTAD and World Bank. The results indicate that none of the 142 countries in the world market of this product have imposed non-tariff trade barriers on the import of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. The developed countries and the countries with transition economies are the main world import partners. European Union, United States, China, Japan, South Korea, Canada, Singapore, Taiwan, Thailand, South Africa, Australia, Turkey, Brazil, Sweden and Belarus are the examples and have imposed low custom tariffs on Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude.

Dossiê do Barreado / Barreado Dossier

Directory of Open Access Journals (Sweden)

Joana Pellerano

2015-04-01

Full Text Available A presente resenha apresenta o livro Cozinhando a tradição: Festa, cultura, história e turismo no litoral paranaense, de Maria Henriqueta Sperandio Garcia Gimenes-Minasse, publicado em 2013 pela Editora UFPR. A obra apresenta a história do Barreado, prato tradicional do litoral do Paraná, as transformações que aconteceram no preparo e no consumo e sua relação com o desenvolvimento econômico e turístico da região, que se vê representada na sua preparação culinária. Barreado Dossier - This review presents the book Cooking tradition: Party, culture, history and tourism in the coast of Paraná, of Henrietta Maria Garcia Sperandio Gimenes-Minasse, published in 2013 by UFPR Press. The book presents the history of Barreado, traditional dish of the coast of Paraná, the changes in its preparation and consumption and its relation to economic development and tourism in the region represented in its culinary preparation. 

JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

Energy Technology Data Exchange (ETDEWEB)

Jason Laumb; John Kay; Michael Jones; Brandon Pavlish; Nicholas Lentz; Donald McCollor; Kevin Galbreath

2009-03-29

The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

Prediction of Marshall Parameters of Modified Bituminous Mixtures Using Artificial Intelligence Techniques

Directory of Open Access Journals (Sweden)

Sunil Khuntia

2014-09-01

Full Text Available This study presents the application of artificial neural networks (ANN and least square support vector machine (LS-SVM for prediction of Marshall parameters obtained from Marshall tests for waste polyethylene (PE modified bituminous mixtures. Waste polyethylene in the form of fibres processed from utilized milk packets has been used to modify the bituminous mixes in order to improve their engineering properties. Marshall tests were carried out on mix specimens with variations in polyethylene and bitumen contents. It has been observed that the addition of waste polyethylene results in the improvement of Marshall characteristics such as stability, flow value and air voids, used to evaluate a bituminous mix. The proposed neural network (NN model uses the quantities of ingredients used for preparation of Marshall specimens such as polyethylene, bitumen and aggregate in order to predict the Marshall stability, flow value and air voids obtained from the tests. Out of two techniques used, the NN based model is found to be compact, reliable and predictable when compared with LS-SVM model. A sensitivity analysis has been performed to identify the importance of the parameters considered.

Dossier 'thermal regulation 2000'. Reconciling building and environment; Dossier RT 2000. Reconcilier batiment et environnement

Energy Technology Data Exchange (ETDEWEB)

Grumel, N.

2001-04-01

The works that led to the setup of the new French thermal regulation (TR 2000) for buildings started in 1997 and were carried out by the general direction of urbanism, accommodation and construction (DGUHC) of the ministry of equipment, transport and accommodation, by the agency of environment and energy mastery (Ademe) and by the scientific and technical committee of building trade. The different steps of buildings construction have been reviewed with specialists, industrialists, energy suppliers, design offices, federation of companies and other professional organisms, in order to reduce the energy consumption of buildings and their impact on the environment. The new regulation is based on the determination of the 'C coefficient', the conventional energy consumption coefficient, and of reference values for the six steps of the elaboration of a construction project. The TR 2000 will be enforced in June 1, 2001. Today, the air conditioning is not concerned by the TR 2000, but will be included in 2003. This dossier presents the different aspects of the new thermal regulation. (J.S.)

Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Bauman, R.F.; Coless, L.A.; Davis, S.M. [and others

1995-12-31

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263. Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.

Wetting of bituminized ion-exchangers under simulated repository conditions

International Nuclear Information System (INIS)

Aalto, H.; Valkiainen, M.

2001-01-01

According to the present plans the spent nuclear fuel from four Finnish nuclear power units will be transferred after interim storage to the final disposal site where it will be encapsulated and disposed of in a final repository constructed into the bedrock at a depth of 500 meters. Low and medium level waste generated at nuclear power plants will be finally disposed of in caverns constructed in the bedrock at the power plant site. The safety of the final disposal is based on a multibarrier concept and the degree of safety is estimated by using predictive models. The properties of the waste form are taken into account in the design of the repository construction. Bitumen has been chosen as an immobilisation agent for the wet wastes at Olkiluoto Power Plant, where two BWR units, TVO 1 and TVO 2, have separate bituminization facilities designed by Asea-Atom. Properties of bituminized spent ion-exchange resins from Olkiluoto power plant have been studied by VTT Chemical Technology since the late 70's. These studies have concentrated mainly on determining the long-term behaviour of the bituminization product under the repository conditions. Current interest lies on wetted product as a diffusion barrier. For this purpose a microscopic method for the visualisation of the structure of the wetted product has been developed. The equilibration of the samples in simulated concrete groundwater is currently going on at a temperature of 5-8 deg. C. Preliminary results are presented in this paper. Diffusion experiments have been planned for the further characterising of the wetted product as a release barrier for radionuclides including modelling. (author)

Low NOx firing systems for bituminous coal and lignite

International Nuclear Information System (INIS)

Knyrim, W.; Scheffknecht, G.

1997-01-01

In the case of lignite fluidized boilers the denitrification down to less than 200 mg/m 3 was possible with primary measures on the firing side only. On account of the excellent results achieved with the reconstructed plants the firing systems for the new generation of brown coal fire steam generators with a capacity of 800 MW and more is designed in a similar way. For bituminous coal fire steam generators the primary measures on the firing side are nor sufficient to keep the German NO x emission limit. Therefore these units had to be retrofitted with a SCR-DENOX plant. The experience with the new firing system made in a 110 MW steam generator in Austria with a wide range of fuels is introduced. One of the largest bituminous coal fired once-trough steam generator built by EVT is the boiler for the power station Bexbach I (750 MW). The firing system is designed as a tangential firing system with 32 jet burners. These are arranged in pairs in the corners and divided into 4 burner levels with 4 burner pairs each. One mill is allocated to each burner level. An important characteristic feature is that the four bowl mills are arranged on one side of the steam generator. The plant is constructed with upper air nozzles which are arranged above the top burner level for the reduced of nitrogen oxides. During tests at steam generator with similar design, the nO x formation could be reduced from 750 to 500 mg/m 3 s.t.p. (dry, 6% O 2 ) with an addition of upper air of 20% at 100% unit capacity and constant total flow. As a main approach for the further reduction of the primary NO x emission at bituminous coal fired steam generators with tangential firing systems, the experience gained from the firing of brown coal has also been taken into account. A fundamental aspect in this respect was the vertical air staging in the direction of the furnace height. The results of many tests in a test reactor have shown that the differences of the achievable NO x values of brown and

Bituminization of radioactive wastes at the Nuclear Research Center Karlsruhe. Experience from plant operation and development work

Energy Technology Data Exchange (ETDEWEB)

Hild, W; Kluger, W; Krause, H

1976-05-01

A summary is given of the main operational experience gained at the Nuclear Research Center Karlsruhe in 4 years operation of the bituminization plant for evaporator concentrates from low- and medium level wastes. At the same time some of the essential results are compiled that have been obtained in the R + D activities on bituminization.

Comparative study of test methods for bituminized and other low- and medium-level solidified waste materials

International Nuclear Information System (INIS)

Brodersen, K.; Mose Pedersen, B.; Vinther, A.

1983-12-01

Various aspects of the behaviour of bituminized or cemented simulated low- or medium-level radioactive waste in contact with water or salt solutions have been investigated. The solubility (approximately 0.5%) and the diffusion coefficient (approximately 5.10 -8 cm 2 /sec) determining transort of water in pure bitumen have been measured for Mexphalte 40/50 at room temperature. A weighing method has been used to study water uptake and swelling of bituminized sodium nitrate, sodium sulphate or cation-exchange resin. The swelling of samples in contact with water was in some cases very pronounced. In strong salt solutions the tendency to swell is much less. The particle size of the embedded waste material is an important parameter. Thermal pre-treatment of cation-exchange resin before bituminization does not seem to improve the quality of the final product. The interaction between bituminized-exchange resin and concrete barrier materials has been studied. Microbial degradation of bitumen and bituminized waste under aerobic conditions has been investigated. It is probably of minor importance as far as leaching is concerned. A method for measuring leaching from a plane surface of cemented waste has been developed. The method avoids the problem of cracks between the sample and the container. Leaching from cemented sodium nitrate or sulphate was investigated. Absorption of CO 2 from the atmosphere was found to have only minor effect on Cs- and Na-leaching but gave a pronounced decrease in Ca-leaching. The use of silica-fume as an additive to cemented sodium nitrate decreased the leach rate by a factor 4. (author)

Waste package transfer, emplacement and retrievability in the French deep geological repository

Energy Technology Data Exchange (ETDEWEB)

Roulet, Alain; Delort, Daniel; Herve, Jean Francois; Bosgiraud, Jean Michel; Guenin, Jean Jacques [Technical Department ANDRA (France)

2009-06-15

Safe, reliable and reversible handling of waste is a significant issue related to the design and safety assessment of deep geological repository in France. The first step taken was to study various waste handling solutions. ANDRA also decided to fabricate and demonstrate industrial scale handling equipment for HLW (since 2003) and for ILW-LL wastes (since 2008). We will review the main equipment developed for the transfer process in the repository, for both types of waste, and underline the benefits of developing industrial demonstrators within the framework of international cooperation agreements. Waste retrieval capability will be simultaneously examined. Two types of waste have to be handled underground in Andra's repository. The HLW disposal package for vitrified waste is a 2 ton carbon steel cylindrical canister with a diameter of 600 mm. The weight of ILW-LL concrete disposal packages range from a minimum of 6 tonnes to over 20 tonnes, and their volume from approximately 5 to 10 m3. The underground transfer to the disposal drift requires moving the disposal package within a shielded transfer cask placed on a trailer. Transfer cask design has evolved since 2005, due to optimisation studies and as a result of industrial feedback from SKB. For HLW handling equipment two design options have been studied. In the first solution (Andra's Dossier 2005), the waste package are emplaced, one at a time, in the disposal drift by a pushing robot. Successive steps in design and proto-typing have lead to improve the design of the equipment and to gain confidence. Recently a fully integrated process has been successfully demonstrated, at full scale, (in a 100 m long mock up drift) as part of the EC funded ESDRED Project. This demonstrator is now on display in Andra's Technology Centre at Saudron, near the Bure Underground Laboratory. The second disposal option which has been investigated is based on a concept of utilising an external apparatus to push a row of

Manx Gaelic: The Manx Gaelic Language in Education in the Isle of Man. Regional Dossiers Series

Science.gov (United States)

McArdle, Fiona, Comp.; Teare, Robert, Comp.

2016-01-01

This regional dossier aims at providing a concise description of and basic statistics on minority language education in a specific region of Europe--the Isle of Man. Aspects that are addressed include features of the education system, recent educational policies, main actors, legal arrangements, and support structures, as well as quantitative…

North Frisian: The North Frisian Language in Education in Germany, 3rd Edition. Regional Dossiers Series

Science.gov (United States)

Walker, Alastair G. H., Comp.

2015-01-01

This regional dossier aims to provide a concise, description and basic statistics about minority language education in a specific region of Europe. Aspects that are addressed include features of the education system, recent educational policies, main actors, legal arrangements, and support structures, as well as quantitative aspects, such as the…

Presentación al Dossier de Historia Pública

Directory of Open Access Journals (Sweden)

Diana González Rey

2014-12-01

Full Text Available Con este número cumplimos ocho ediciones de la revista Historia 2.0: Conocimiento Histórico en Clave Digital. Con una política editorial abierta, la revista ha logrado mantener su espacio en la red y su carácter de edición para jóvenes historiadores. La siguiente edición que gratamente les presentamos a nuestros lectores es resultado de un proceso de evaluación variopinto, una continuación del dossier iniciado en la edición número siete dedicado a la historia ambiental. Como complemento se presenta un interesante apartado que pretende abrir el debate en torno a la historia pública, un campo que aunque ha ganado un espacio de especialización en Estados Unidos y Europa es prácticamente desconocido en América Latina.

DEPOSITIONAL ENVIRONMENT AND ORGANIC GEOCHEMICAL CHARACTERISTICS OF LOWER EOCENE BITUMINOUS ROCKS, IN THE KÜRNÜÇ/GÖYNÜK-BOLU AREA

Directory of Open Access Journals (Sweden)

Ali SARI

2016-12-01

Full Text Available In this study, dark gray and dark brown colored, organic-carbon rich bituminous rocks (bituminous marl and bituminous shale exposing around the Kürnüç area (Göynük, Bolu are investigated by means of or- ganic geochemical characteristics. In this respect, rock lithologies, depositional environments, rock source potential, kerogen and organic maturity types and hydrocarbon generation potentials of bituminous rocks were determined. For this reason, pyrolysis (Rock Eval–VI analysis, gas chromatography (GC and gas chromatography-mass spectrometer (GC-MS analyses were carried out. In addition, spore color index (SCI was determined with organic petrographic method and stable carbon analysis (δ13C of the samples were also conducted. Lithology of the studied samples is of clastic source and the depositional environ- ment is a lagoon with a partial connection to the sea. In bituminous rocks with excellent source rock potential TOC values are in the range of 2.52-8.38 wt % (average 6.08 wt %. With the exception of two samples (Type II kerogen type of all samples is Type I. According to pyrolysis, GC and GC-MS organic maturity results, all the samples are in immature stage. Organic geochemical data indicate that bituminous rocks have an excellent oil generation potential and there is no organic contamination.

Long-term behaviour of bituminized waste: modelling self-irradiation and leaching

International Nuclear Information System (INIS)

Simondi-Teisseire, B.; Vistoli, P.P.; Libert, M.; Gilardi, T.; Chaix, P.; Blanc, V.

2001-01-01

During interim storage, the main evolution factor of bituminized wastes is radiolysis, due to self-irradiation. In deep disposal conditions, after site re-saturation and corrosion of the containers, the main evolution will be due to leaching. This paper deals with two models designed to describe respectively radiolytic gas evacuation (JACOB- 2) and bituminized waste leaching (COLONBO), and some of the typical results obtained from these two models. The first model describes radiolytic gas production, diffusive transport of gas, bubble nucleation and ripening and movement under buoyancy. The second one is based on descriptions of water sorption, solubilization, and diffusion into the matrix, water uptake by the most soluble salts leading to alteration of the matrix and finally to diffusive transport of the salts outside the bitumenisate. (author)

Method for obtaining a varnish with a base of mineral oil obtained by distillation of bituminous schists

Energy Technology Data Exchange (ETDEWEB)

Marchionni, A

1945-07-24

A method for obtaining a varnish is described characterized by the fact that the following ingredients are being used; mineral oil from the distillation of bituminous schists in the proportions already cited in the description, diluted with benzene or turpentine, with admixture of coloring matter. Varnish with a base of mineral oil from the distillation of bituminous schists is obtained.

Evaluation de la qualité de la tenue des dossiers médicaux des ...

African Journals Online (AJOL)

Evaluation de la qualité de la tenue des dossiers médicaux des patientes en gynécologie et en obstétrique dans un Centre hospitalier universitaire de référence, Burkina Faso. H. Zamané, S. Kiemtoré, I. Ouédraogo, P.D. Kaïn, Y.A. Sawadogo, S.D. Sanou, A. Ouattara, A. Dembélé, J. Lankoandé ...

Noise Reduction Properties of an Experimental Bituminous Slurry with Crumb Rubber Incorporated by the Dry Process

Directory of Open Access Journals (Sweden)

Moisés Bueno

2014-08-01

Full Text Available Nowadays, cold technology for asphalt pavement in the field of road construction is considered as an alternative solution to conventional procedures from both an economic and environmental point of view. Among these techniques, bituminous slurry surfacing is obtaining an important role due to the properties of the obtained wearing course. The functional performance of this type of surfaces is directly related to its rough texture. Nevertheless, this parameter has a significant influence on the tire/road noise generation. To reduce this undesirable effect on the sound performance, new designs of elastic bituminous slurries have been developed. Within the FENIX project, this work presents the acoustical characterization of an experimental bituminous slurry with crumb rubber from wasted automobile tires incorporated by the dry process. The obtained results show that, under controlled operational parameters, the close proximity sound levels associated to the experimental slurry are considerably lower than those emitted by a conventional slurry wearing course. However, after one year of supporting traffic loads and different weather conditions, the evaluated bituminous slurry, although it conserves the original noise reduction properties in relation to the conventional one, noticeably increases the generated sound emission. Therefore, it is required to continue improving the design of experimental surfaces in order to enhance its long-term performance.

Leaching test of bituminized waste and waste solidified by epoxy resin

International Nuclear Information System (INIS)

Yoshinaka, Kazuyuki; Sugaya, Atsushi; Onizawa, Toshikazu; Takano, Yugo; Kimura, Yukihiko

2008-10-01

About 30,000 bituminized waste drums and about 1800 drums of waste solidified by epoxy resin, generated from Tokai Reprocessing Plant, were stored in storage facilities. And study for disposal of these waste is performed. It was considered that radioactive nuclides and chemical components were released from these waste by contact of underground water, when disposed there waste. This paper is reported that result of leaching tests for these waste, done from 2003 to 2006. We've get precious knowledge and data, as follows. (1) In leaching tests for bituminized waste, it has detected iodine-129 peak, considered difficult too low energy gamma to detect. We've get data and knowledge of iodine-129 behavior first. Leached radioactivity for 50 days calculated by peak area was equal for about 40% and 100% of including radioactivity in bituminized waste sample. And we've get data of behavior of nitric acid ion and so on, important to study for disposal, in various condition of sample shape or leaching liquid temperature. (2) In leaching test for waste solidified by epoxy resin, we've get data of behavior of TBP, radionuclides and so on, important to study for disposal. Leached TBP was equal about 1% of including of sample. And we've get data of iodine-129 behavior, too. It was confirmed that leached iodine-129 was equal for about 60% and 100% of including sample, for 90 days. (author)

Process for carbonization of bituminous combustibles

Energy Technology Data Exchange (ETDEWEB)

1923-02-02

A process for the carbonizing of bituminous materials is characterized in that the material is exposed to the action of radiant heat by insertion of a gas layer between the charge and the gasflames and at the same time to convection heating. The process spreads the material on a permeable support and by employing generator gases form the spent residue and if necessary also the permanent gases from the condenser for heating is characterized in that these gases are conducted directly over the material, and partly passed through it and partly burned over it by means of air.

Dossier for marketing authorization in the European union

Directory of Open Access Journals (Sweden)

Maida Todić

2003-02-01

Full Text Available Extensive and complete documentation must be presented for marketing authorization of a medicinal product in the EU. Presented documentation should prove quality, safety and efficacy of the medicinal product. It is ensured that the applicant supplies the authorities with complete information. The legislation in Federation of Bosnia and Herzegovina has also taken more steps towards those European directions.The presentation and content of the dossier in the European Union has been redefined. The “old” EU format will be replaced with the Common Technical Document (EU CTD format agreed in 2000, within the International Conference on Harmonization framework. These two formats are intended to coexist during the transition period until July 2003. The CTD is an internationally agreed upon format for the preparation of a well structured presentation for applications to be submitted to regulatory authorities in the three ICH regions of Europe, US and Japan.

Nigerian bituminous coal as a fuel-coal. | OGUGBUAJA | Global ...

African Journals Online (AJOL)

Nigerian bituminous coal as a fuel-coal. V O OGUGBUAJA, C L NDIOKWERE, G A DIMARI. http://dx.doi.org/10.4314/gjpas.v6i2.16113 · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL ...

The microstructure of petroleum vacuum residue films for bituminous concrete: a microscopy approach.

Science.gov (United States)

Sourty, E D; Tamminga, A Y; Michels, M A J; Vellinga, W-P; Meijer, H E H

2011-02-01

Selected carbon-rich refinery residues ('binders') mixed with mineral particles can form composite materials ('bituminous concrete') with bulk mechanical properties comparable to those of cement concrete. The microstructural mechanism underlying the remarkable composite properties has been related to the appearance of a rigid percolating network consisting of asphaltenes and mineral particles [Wilbrink M. et al. (2005) Rigidity percolation in dispersions with a structured visco-elastic matrix. Phys. Rev. E71, 031402]. In this paper, we explore the microstructure of thin binder films of varying thickness with a number of microscopic characterization techniques, and attempt to relate the observed microstructure to the distinctive mechanical behaviour. Two binders, only one of which has been proven to be suitable for bituminous concrete were investigated, and their microstructure compared. Both binders show the formation of asphaltene aggregates. The binder suitable for bituminous concrete is distinguished by the fact that the asphaltenes show a stronger tendency towards such aggregation, due to a higher concentration and less stabilization in the maltene phase. They also show a clear affinity to other species (such as waxes) and may act as nucleation sites for crystals and aggregates of those species. © 2010 The Authors Journal compilation © 2010 The Royal Microscopical Society.

Effects of graphite on rheological and conventional properties of bituminous binders

Directory of Open Access Journals (Sweden)

Yunus Erkuş

2017-07-01

Full Text Available In this study, the effects of graphite used for developing the rheological and conventional properties of bitumen were investigated using various bituminous binder tests. Penetration, softening point, rotational viscosity (RV, dynamic shear rheometer (DSR and bending beam rheometer (BBR tests were applied to bituminous binders modified with four different proportions of graphite by bitumen weight. The penetration values declined while softening point values increased with rising graphite content. While graphite induced 8 °C increases in mixing-compacting temperature by increasing the viscosity values, it also increased the rutting parameter. According to the BBR test, the deformation and stiffness values changed significantly with increasing graphite content, but the m-values did not change significantly. These results showed that graphite generally used for improving the thermal properties can improve to high temperature performance of mixtures. Keywords: Graphite, Bitumen, Conventional properties, Rheological properties

DOSSIER: Intelectuales y Editores

Directory of Open Access Journals (Sweden)

Gustavo Sorá

2009-04-01

Full Text Available El intelectual abre ideas, el editor las cierra. El escritor produce textos, el editor impresos. El intelectualescribe pero es el editor quien publica. No por nada, afirman algunos psicólogos, el pensamientoculmina con su publicación. Entre el escritor y el editor se moviliza una energía simbólica y socialsublimada bajo las líneas impresas que llegan al lector. Ese entre-lugar de producción de sentidos, decosmologías, de sociedad que marcó la formación de gran parte de las culturas desde la aparición de laexpresión gráfica de las ideas, permanece como un problema esquivo para la investigación, al menospara la antropología practicada en estas latitudes. Parece una cuestión obturada por el dominanteacúmulo de historias de las ideas, de la literatura, del pensamiento que reactualizan la oposición entreespíritu y materia, estética y sociedad, texto y contexto. Evidencia de ello es la clausura sufrida por lasociología de la literatura, una sub-disciplina tan incómoda para los guardianes del aura del genioliterario nacional.Este dossier busca iluminar esa relación con la certeza de que modela uno de los terrenos másfértiles para repensar el legado de la historia de la cultura en occidente y para generar un basto programade problemas de investigación escasamente explorados por las ciencias sociales y humanas en AméricaLatina, y aplicables al estudio de toda cultura, con o sin escritura.

Presentación Dossier Tema Libre

Directory of Open Access Journals (Sweden)

Diana González Rey

2015-12-01

Full Text Available Con el décimo número de la Revista Historia 2.0: Conocimiento Histórico en Clave Digital, los editores saludamos a los lectores. Durante estos cinco años la publicación ha pasado por diversas etapas de aprendizaje en las que destacamos el apoyo de los autores, estudiantes y de los profesionales de la historia que contribuyen a divulgar y sostener la edición. Hemos querido celebrar nuestros cinco años con un dossier de Tema Libre, tal como fue él de nuestra primera entrega, en ésta nueva edición número diez (10. Los artículos aquí publicados fueron al igual que en todas las ediciones convocados públicamente, en la página de Facebook de AHISAB, a través la distribución mediante listas de correos, de servidores gratuitos como H- México, quiénes nos han colaborado en el proceso de distribución de las convocatorias. Igualmente la evaluación por pares fue de manera anónima de acuerdo a todos los estándares internacionales, una labor que debemos agradecer notoriamente púes constituye la base fundamental y académica de nuestra publicación.

Nagra technical report 14-02, geological basics - Dossier VII - Usage conflicts

International Nuclear Information System (INIS)

Gautschi, A.; Becker, J.; Traber, D.; Leu, W.

2014-01-01

This dossier is the seventh of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It discusses possible conflicts with respect to the use of rock strata below or above the proposed host rock layers. Possible usage could include the extraction of salt, coal or other hydrocarbons. Other possible conflicting uses include the mining of stone, ores and minerals as well as the extraction of mineral water and thermal water. The construction of deep boreholes, for example for geothermal probes, could also cause conflicts with any nuclear waste depositories. The storage of natural gas or carbon sequestration, however, is not considered likely

The UP/SP merger could derail Western bituminous

International Nuclear Information System (INIS)

Vaninetti, J.; Leshock, J.C.

1995-01-01

The 3 billion dollars per year US Western bituminous coal industry annually produces more than 100 million tons of compliance coal to utility, industrial and export markets. About half of production is consumed locally, this sector has grown most in recent years. New markets are utilities in the Mid-west. The UP and SP railroads have profited accordingly. The merger may cause a change in the pricing strategies for the new company, leading to increased freight and coal prices. 1 fig., 1 tab

Relations among pH, sulfate, and metals concentrations in anthracite and bituminous coal-mine discharges, Pennsylvania

Science.gov (United States)

Cravotta, III, Charles A.

2006-01-01

Water-quality data for discharges from 140 abandoned mines in the Bituminous and Anthracite Coalfields of Pennsylvania illustrate relations among pH, sulfate, and dissolved metal concentrations. The pH for the 140 samples ranged from 2.7 to 7.3, with two modes at pH 2.5 to 4 (acidic) and 6 to 7 (near neutral). Generally, flow rates were smaller and solute concentrations were greater for low-pH samples; flow rates increased with pH. Although the pH distribution was similar for the bituminous and anthracite subsets, the bituminous discharges had smaller median flow rates, greater concentrations of sulfate, iron, and aluminum, and smaller concentrations of barium and lead than anthracite discharges with the same pH values. The observed relations between the pH and constituent concentrations can be attributed to (1) dilution of acidic water by alkaline ground water; (2) solubility control of aluminum, iron, manganese, barium, and lead by hydroxide, sulfate, and/or carbonate minerals; and (3) aqueous sulfate-complex formation. The formation of AlSO4+ and AlHSO4+2 complexes adds to the total dissolved aluminum concentration at pH of equilibrium with aluminum hydroxide or hydroxysulfate minerals and can account for 10 to 20 times greater concentrations of dissolved aluminum in bituminous discharges compared to anthracite discharges at similar pH. Sulfate complexation also can account for 10 to 30 times greater concentrations of dissolved ferric iron concentrations at equilibrium with ferrihydrite (Fe(OH)3) and/or schwertmannite (Fe8O8(OH)4.5(SO4)1.75) at pH of 3 to 5. In contrast, lower barium and lead concentrations in bituminous than anthracite discharges indicates elevated sulfate concentration could decrease mobility of these metals by the formation of insoluble minerals such as barite (BaSO4) or anglesite (PbSO4). Most samples were saturated with barite, but none were saturated with anglesite. Hence, lead concentrations could be controlled by coprecipitation with

Os dossiês da REF: além das fronteiras entre academia e militância REF's dossiers: crossing the border between research and politics

Directory of Open Access Journals (Sweden)

Sônia Weidner Maluf

2004-12-01

Full Text Available Este artigo, apresentado originalmente no Encontro da REDEFEM em outubro de 2002, discute os Dossiês publicados desde o surgimento da Revista Estudos Feministas até o presente momento, fazendo um levantamento e uma breve descrição de cada um deles. Os Dossiês constituem uma seção da REF e se dedicam à abertura de um espaço de diálogo entre a produção acadêmica e intelectual e a militância, o ativismo e as políticas feministas. Os textos podem assumir diversos formatos além de artigos ou de ensaios acadêmicos. No final deste artigo, é feita uma breve análise do lugar dos dossiês nas fricções entre academia e militância, buscando ir além das dicotomias entre ação e reflexão ou teoria e prática.This article analyzes the Dossiers of Revista Estudos Feministas. This section is published since the appearance of the journal on 1992. We describe each one of the 24 dossiers published until now and analyze it main characteristics. The main objective of the Dossiers is to establish a dialogue between the feminist academic discussions and the feminist activism and politics. They are open to different styles of text beyond the academic paper. In the end of the article we analyze the place of the dossiers in the discussions about the tensions between academy and activism, trying to go beyond the dichotomies between action and reflection or between theory and practice.

Clay 2001 dossier: progress report on feasibility studies and research into deep geological disposal of high-level, long-lived waste

International Nuclear Information System (INIS)

2001-12-01

A French Act of Parliament passed on 30 December 1991 set out the main areas of research required to prepare solutions for the long-term management of high-level, long-lived radioactive waste. The three avenues of research listed in the Act included a feasibility study of the deep geological disposal of these waste, with responsibility for steering the study given to ANDRA, France National Agency for Radioactive Waste Management. Following government decisions taken in 1998, the study focused on two types of geological medium, clay and granite. The clay formations study is essentially based on results from an underground laboratory sited at the border between the Meuse and Haute-Marne departments, where the Callovo-Oxfordian argillite beds are being investigated. No site has yet been chosen for an underground laboratory for the granite study, so for the time being this will draw on generic work and on research carried out in laboratories outside France. ANDRA has decided to present an initial report on the results of its research programme, publishing a dossier on the work on clay formations in 2001 with a second dossier covering the work on granite due for release in 2002. This dossier is thus a review of the work carried out by ANDRA on the feasibility study into a radioactive waste repository in a clay formation. It represents one step in a process of studies and research work leading up to the submission of a report due in 2005 containing ANDRA conclusions on the feasibility of a repository in the clay formation. (author)

Dossier: sirvientas, trabajadoras y activistas. El género en la historia social inglesa

OpenAIRE

Pita, Valeria Silvina; Andújar, Andrea Norma; Palermo, Silvana; Schettini, Cristiana

2015-01-01

Este trabajo es la introducción al dossier "?Sirvientas, trabajadoras y activistas. El género en la historia social inglesa?, el cual reúne artículos de Dorothy Thompson, Catherine Hall y Carolyn Steedman, tres historiadoras británicas pertenecientes a distintas generaciones e inscriptas en la tradición de la historia social marxista. Los textos que aquí se presentan abordan el estudio de diversas experiencias de trabajo y organización de la clase trabajadora en la Inglaterra de los albores ...

El patrimonio como domesticación de la cultura. Comentarios al Dossier de ICONOS 20

Directory of Open Access Journals (Sweden)

Espinheira , Gey

2005-01-01

Full Text Available Tres de los artículos publicados en el dossier de ICONOS 20 ¿Patrimonio, memoria y ¿regeneración¿ urbana¿, convergen en reconocer algunos efectos perversos de la restauración de centros históricos y espacios públicos. Este artículo explora los argumentos presentados en esos artículos y los entiende como parte de un proceso que, en nombre del turismo, domestica la cultura.

Gamma radiation hazard to miners in bituminous coal mines

International Nuclear Information System (INIS)

Skubacz, K.

1986-01-01

Radiation hazard to miners working in 16 bituminous coal mines was determined by a thermoluminescence method. While the miners exposure to gamma radiation is higher than that of the general population, the yearly dose was never found to exceed 5 mSv in any investigated person. Factors contributing to the estimate of the exposure hazard and the need for individual dose monitoring in mines are discussed in more detail. 3 refs., 4 figs. (author)

Fatigue behaviour of bituminous materials : from binders to mixes

OpenAIRE

SOENEN, H; DE LA ROCHE, C; REDELIUS, P

2003-01-01

Test procedures, aiming at measuring fatigue directly on bituminous binders, are increasingly used. The purpose of this paper is to investigate the relevance of this type of binder fatigue tests and to compare the results with laboratory fatigue properties of the corresponding mixes, using one mix composition for all binders, and similar fatigue tests conditions. Eight binders were selected, derived from two crude sources, including an oxidised and two polymer modified samples. All fatigue te...

Chemomechanics of Damage Accumulation and Damage-Recovery Healing in Bituminous Asphalt Binders

NARCIS (Netherlands)

Pauli, A.T.

2014-01-01

As a contribution to the development of mutli-scale multi-physics approaches to modelling pavement performance, the present thesis considers the topic of damage accumulation accompanied by damage recover self-healing of the bituminous asphalt phase of pavement systems. It is found insightful that by

Research on the thermal decomposition of Mongolian Baganuur lignite and Naryn sukhait bituminous coal

Directory of Open Access Journals (Sweden)

A. Ariunaa

2016-03-01

Full Text Available The technical characteristics, elemental composition of the organic and mineral matters, ash melting behaviors and carbonization and gasification reactivities of coals from Baganuur and Naryn sukhait deposits were investigated. The results of proximate and ultimate analysis confirmed that the coal from Baganuur deposit can be graded as a low rank lignite B2 mark coal and Naryn sukhait coal is a bituminous G mark one. The carbonization and gasification experiments were performed using TGA apparatus and fixed bed quartz reactor. The data obtained with two experimental reactors showed that Baganuur lignite had lower thermal stability and much higher CO2 gasification reactivity at 950°C as compared to those for Naryn sukhait bituminous coal.Mongolian Journal of Chemistry 16 (42, 2015, 22-29

Process for recovering oil from shale and other bituminous materials

Energy Technology Data Exchange (ETDEWEB)

1918-08-23

A process for recovering oil from shale and other bituminous minerals in rotary retorts heated from outside and flushed with water vapor or other oxygen-free gases is characterized by the fact that all kinds of minerals are carbonized, and that during the carbonization process the temperature of the superheated steam or gases is about 50/sup 0/ C higher than the temperature of the carbonized mineral.

A Method to Estimate the Dynamic Displacement and Stress of a Multi-layered Pavement with Bituminous or Concrete Materials

Directory of Open Access Journals (Sweden)

Zheng LU

2014-12-01

Full Text Available In this research work, a method to estimate the dynamic characteristics of a multilayered pavement with bituminous or concrete materials is proposed. A mechanical model is established to investigate the dynamic displacement and stress of the multi-layered pavement structure. Both the flexible and the rigid pavements, corresponding to bituminous materials and concrete materials, respectively, are studied. The theoretical solutions of the multi-layered pavement structure are deduced considering the compatibility condition at the interface of the structural layers. By introducing FFT (Fast Fourier Transform algorithm, some numerical results are presented. Comparisons of the theoretical and experimental result implied that the proposed method is reasonable in predicting the stress and displacement of a multi-layered pavement with bituminous or concrete materials. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6071

The microstructure of petroleum vacuum residue films for bituminous concrete: a microscopy approach

NARCIS (Netherlands)

Sourty, E.; Tamminga, A.Y.; Michels, M.A.J.; Vellinga, W.P.; Meijer, H.E.H.

2011-01-01

Selected carbon-rich refinery residues (‘binders’) mixed with mineral particles can form composite materials (‘bituminous concrete’) with bulk mechanical properties comparable to those of cement concrete. The microstructural mechanism underlying the remarkable composite properties has been related

Effect of bituminous coal properties on carbon dioxide and methane high pressure sorption

Czech Academy of Sciences Publication Activity Database

Weishauptová, Zuzana; Přibyl, Oldřich; Sýkorová, Ivana; Machovič, Vladimír

2015-01-01

Roč. 139, JAN 1 (2015), s. 115-124 ISSN 0016-2361 Institutional support: RVO:67985891 Keywords : bituminous coal * sorption capacity * maceral composition * Upper Silesian Coal Basin Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.611, year: 2015

Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

Directory of Open Access Journals (Sweden)

Dipankar Sarkar

2016-01-01

Full Text Available There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46, 0.50, 0.54, and 0.60 of the weight of brick aggregates. Marshall Method of mix design is carried out to find the optimum bitumen content of such bituminous concrete mix prepared by plastic coated OBBA. Bulk density, Marshall Stability, flow, Marshall Quotient, ITS, TSR, stripping, fatigue life, and deformations have been determined accordingly. Marshall Stability value of 0.54 percent of plastic mix is comparatively higher than the other mixes except 0.60 percent of plastic mix. Test results are within the prescribed limit for 0.54 percent of plastic mix. There is a significant reduction in rutting characteristics of the same plastic mix. The fatigue life of the mix is also significantly higher. Thus plastic coated OBBA is found suitable in construction of bituminous concrete road.

Carbon Isotope Analyses of Individual Hydrocarbon Molecules in Bituminous Coal, Oil Shale and Murchison Meteorite

Directory of Open Access Journals (Sweden)

Kyoungsook Kim

1998-06-01

Full Text Available To study the origin of organic matter in meteorite, terrestrial rocks which contain organic compounds similar to the ones found in carbonaceous chondrites are studied and compared with Murchison meteorite. Hydrocarbon molecules were extracted by benzene and methanol from bituminous coal and oil shale and the extracts were partitioned into aliphatic, aromatic, and polar fractions by silica gel column chromatography. Carbon isotopic ratios in each fractions were analysed by GC-C-IRMS. Molecular compound identifications were carried by GC-MS Engine. Bituminous coal and oil shale show the organic compound composition similar to that of meteorite. Oil shale has a wide range of δ(13C, -20.1%_0 - -54.4%_0 compared to bituminous coal, -25.2%_0 - -34.3%_0. Delta values of several molecular compounds in two terrestrial samples are different. They show several distinct distributions in isotopic ratios compared to those of meteorite; Murchison meteorite has a range of δ(13C from -13%_0 to +30%_0. These results provide interpretation for the source and the formation condition of each rock, in particular alteration and migration processes of organic matter. Especially, they show an important clue whether some hydrocarbon molecules observed in meteorite are indigenous or not.

Log evaluation of sub-bituminous coals in Magallanes, Chile

International Nuclear Information System (INIS)

Weltz, L.S.

1976-01-01

In coal exploration a drilling program is normally used for coal inquest through core analysis, with a high cost and operating time. However, in many cases, there is poor cores recovery due to operating procedures and/or formation conditions which leads to the determination of parameters non-representative of the coal seam. The cost and operating time can be minimized through the use of logs which also represent a continuous and in situ sampling. In the case of sub-bituminous coals, the analysis through logs is more complex due to the high content of clay, which masks the presence of water. This paper describes the analysis of sub-bituminous coals in Magallanes-Chile. The main coal seam components are: coal, clay, secondary quartz and water. An interpretation system using the density log, gamma ray, sonic and microlog, based on rho/sub B/-GR and rho/sub B/--Δ/sub T/ cross plots, permits to know the weight percentages of the following elements: total carbon, ash, moisture, which form the main local coal parameters. Empirical relationships permit us to obtain also the heating value and an estimate strength index to elastic-dynamic forces. The results obtained agree within 3 percent with the Laboratory cores analysis. The method is processed through a sequence of simple computer programs for IBM-360

INVESTIGATION ON UTILITY OF PLASTIC WASTE AS AN ADDITIVE FOR BITUMINOUS CONCRETE USING WET PROCESS OF MIXING

Directory of Open Access Journals (Sweden)

Anurag Virendra Tiwari

2017-12-01

Full Text Available Purpose. Plastic waste has become a major environmental issue of concern due to its exponential growth due to rapid urbanization. The paper investigates utility of plastic waste as an additive for bituminous concrete using wet process of mixing. Methodology. The methodology for the present paper has been designed with complex research consisting of Marshall mix design of the bituminous mix added with plastic waste for modifying bitumen using wet process of mixing, performing the tests on the samples and analyzing the results in the form of table and figures. In the present paper LDPE and HDPE type of plastic waste are used to modify the bitumen. Finding. The results show that addition of 6 percent of bitumen improves the Marshall properties of the mix. Use of plastic to modify the bitumen not only makes the road surface more durable but also it is an eco-friendly way of proper disposal of plastic waste. Originality. The processes used for mixing the plastic waste to the bitumen are dry process and wet process. Dry process of mixing the plastic waste to the bituminous mix is most common and lot of study is carried out on its application. In the present paper wet process of mixing has not yet been studied much. Practical Value. The practical application of utilizing the plastic waste to modify bitumen in the bituminous mix improves the stability values resulting in the more durable road surface. Also the method ensures the proper disposal of plastic waste in eco-friendly way.

Biowaste utilization in the process of co-gasification with bituminous coal and lignite

International Nuclear Information System (INIS)

Howaniec, Natalia; Smoliński, Adam

2017-01-01

Biowaste utilization in co-gasification with bituminous coal and lignite gives the benefits of stable supplies of a primary energy source – coal and utilization of a zero-emission, waste material (i.e. agriculture waste, sewage sludge, etc.) with higher process efficiency and lower negative environmental impact than biomass or coal gasification, respectively. The main focus of the study presented is co-gasification of bituminous coal or lignite with biowaste to hydrogen-rich gas. The experiments were performed in the laboratory scale fixed-bed reactor installation at 700 and 900 °C. The Hierarchical Clustering Analysis complemented with a color map of studied data were applied in the selection of the optimal operating parameters for biowaste utilization in the co-gasification process based on the experimental data of gasification/co-gasification process as well as physical and chemical properties of fuels tested. The experimental results showed that the carbon conversion rate in co-gasification increased with increasing biomass content in a fuel. The total gas volume and hydrogen volume in co-gasification were higher than the values expected based on the results of the gasification process of the fuels analyzed. - Highlights: • Biowaste co-gasification with bituminous coal/lignite to hydrogen-rich gas. • Steam co-gasification in laboratory scale fixed-bed reactor at 700 and 900 °C. • Hierarchical Clustering Analysis complemented with color map of experimental data. • Carbon conversion increase with increasing biomass content. • The highest total gas and hydrogen volume in co-gasification of C-B20 blend at 900C.

Carbonization process for bituminous shale, etc

Energy Technology Data Exchange (ETDEWEB)

1917-11-08

A process for uninterrupted carbonization with possibly greater yield of primary products and subsequent burning of the bituminous shale and other material with preponderantly inorganic constituents through direct flushing-through of the gases is characterized by a rustless shaft furnace wider at the bottom with lower inlets for air through the hot residue and air or gas inlets into the burning zone for the purpose of levelling the burning zone on one hand and regulating it in a determined cross section, and on the other hand to make possible ready determination of the temperature of the burning zone, the requisite means (vapor, wet or dry-air, air-hot gas mixture) going into the shaftcasing in the cross section in which the burning zone should be regulated, through an annular movable and double-sided coolable slit.

A new radiometric instrument designed to measure the parameters of bituminous coal on transport belts

International Nuclear Information System (INIS)

Kubicek, P.

1993-01-01

A new radiometric instrument developed in Czechoslovakia, for the measurement of ash content of bituminous coal, and for the determination of approximate values of moisture and weight is described. (Author)

The effect of petrographical composition of coals and bituminous sediments on the material and isotopic composition of dry natural gases from artificial recoalification reactions. 2

International Nuclear Information System (INIS)

Maass, I.; Huebner, H.; Nitzsche, H.-M.; Schuetze, H.; Zschiesche, M.

1975-01-01

Experimental results indicate that on the basis of the material and isotopic composition of natural gases conclusions can be drawn with regard to the character (humic or bituminous) of the parent rock. Thus, genetic relations assumed to exist between humic sediments (e.g. coal seams) and dry natural gases as well as bituminous rocks and wet natural gases are experimentally confirmed. In addition, from analyses of the materials approximate data can be derived on the degree of carbonization of coal or bituminous sediments in the main phase of gas separation. Furthermore, these analyses were used to elucidate the question whether authochthonous or allochthonous deposits are present. It could be shown that the maceral composition of coals and of the organo-petrographical inclusions in bituminous sediments determines the isotopic composition of methane in recoalification gases to a considerable degree. (author)

Slagging behavior of upgraded brown coal and bituminous coal in 145 MW practical coal combustion boiler

Energy Technology Data Exchange (ETDEWEB)

Akiyama, Katsuya; Pak, Haeyang; Takubo, Yoji [Kobe Steel, Ltd, Kobe (Japan). Mechanical Engineering Research Lab.; Tada, Toshiya [Kobe Steel, Ltd, Takasago (Japan). Coal and Energy Technology Dept.; Ueki, Yasuaki [Nagoya Univ. (Japan). Energy Science Div.; Yoshiie, Ryo; Naruse, Ichiro [Nagoya Univ. (Japan). Dept. of Mechanical Science and Engineering

2013-07-01

The purpose of this study is to quantitatively evaluate behaviors of ash deposition during combustion of Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. A blended coal consisting 20 wt% of the UBC and 80 wt% of the bituminous coal was burned for the combustion tests. Before the actual ash deposition tests, the molten slag fractions of ash calculated by chemical equilibrium calculations under the combustion condition was adopted as one of the indices to estimate the tendency of ash deposition. The calculation results showed that the molten slag fraction for UBC ash reached approximately 90% at 1,523 K. However, that for the blended coal ash became about 50%. These calculation results mean that blending the UBC with a bituminous coal played a role in decreasing the molten slag fraction. Next, the ash deposition tests were conducted, using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at 1,523 K in the boiler to measure the amount of ash deposits. The results showed that the mass of deposited ash for the blended coal increased and shape of the deposited ash particles on the tube became large and spherical. This is because the molten slag fraction in ash for the blended coal at 1,523 K increased and the surface of deposited ash became sticky. However, the mass of the deposited ash for the blended coal did not greatly increase and no slagging problems occurred for 8 days of boiler operation under the present blending conditions. Therefore, appropriate blending of the UBC with a bituminous coal enables the UBC to be used with a low ash melting point without any ash deposition problems in a practical boiler.

Natural radioactivity associated with bituminous coal mining in Nigeria

International Nuclear Information System (INIS)

Balogun, F.A.; Mokobia, C.E.; Fasasi, M.K.; Ogundare, F.O.

2003-01-01

Gamma spectroscopic method was used to determine the natural radioactivity associated with the mining of Nigerian bituminous coal for the purpose of determining the radiological implications of coal mining in the country. The activity concentrations of the radionuclides detected range from 0.20±0.002 to 48.42±5.32 Bq kg -1 . The overall natural radionuclide contribution to the radioactivity of the environment was found to be 404.16±23.44 Bq kg -1 . Of this, coal waste (tailing) alone contributed 49.5% representing the largest contribution. Coal contributed just 5.5%. A comparison of the concentrations obtained in this work for coal with those from other parts of the world indicates that the radioactivity content of the Nigerian bituminous coal is not significantly different. The outdoor and indoor exposure rates in air 1 m above the ground are estimated to be (6.31±1.20)x10 -8 and (7.57±1.20) x10 -8 Gy h -1 , respectively, for the mining environment. These values compare very well with the global values reported by UNSCEAR: 5x10 -8 and 6x10 -8 Gy h -1 , respectively. The resulting annual effective dose equivalent estimated is (4.49±0.74)x10 -4 Sv yr -1 . This also compares favourably with the global value -4x10 -4 Sv yr -1 , reported by UNSCEAR

Towards an Accurate Stress Dependant Time & Frequency Domain VE Response Model for Bituminous Binders

NARCIS (Netherlands)

Woldekidan, M.F.; Huurman, M.; Pronk, A.C.

2010-01-01

Linear viscoelastic properties of bituminous binders for short loading times are analyzed using dynamic mechanical analysis methods. Dynamic Shear Rheometer (DSR) test with parallel plate (PP) configuration is widely used for this purpose. Due to the complex stress distribution over the

Clay 2001 dossier: progress report on feasibility studies and research into deep geological disposal of high-level, long-lived waste; Dossier 2001 argile: sur l'avancement des etudes et recherches relatives a la faisabilite d'un stockage de dechets a haute activite et a vie longue en formation geologique profonde

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-12-01

A French Act of Parliament passed on 30 December 1991 set out the main areas of research required to prepare solutions for the long-term management of high-level, long-lived radioactive waste. The three avenues of research listed in the Act included a feasibility study of the deep geological disposal of these waste, with responsibility for steering the study given to ANDRA, France National Agency for Radioactive Waste Management. Following government decisions taken in 1998, the study focused on two types of geological medium, clay and granite. The clay formations study is essentially based on results from an underground laboratory sited at the border between the Meuse and Haute-Marne departments, where the Callovo-Oxfordian argillite beds are being investigated. No site has yet been chosen for an underground laboratory for the granite study, so for the time being this will draw on generic work and on research carried out in laboratories outside France. ANDRA has decided to present an initial report on the results of its research programme, publishing a dossier on the work on clay formations in 2001 with a second dossier covering the work on granite due for release in 2002. This dossier is thus a review of the work carried out by ANDRA on the feasibility study into a radioactive waste repository in a clay formation. It represents one step in a process of studies and research work leading up to the submission of a report due in 2005 containing ANDRA conclusions on the feasibility of a repository in the clay formation. (author)

Zeolite facies and regional rank of bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Kisch, H J

1966-01-01

The author has correlated diagnostic analcime-, heulandite-, and laumontite-bearing mineral assemblages from four areas in the Upper Carboniferous and the Permian of New South Wales with the rank of the associated coals, represented by the carbon content of vitrinite. The results show that lowest-grade regional metamorphism of the zeolite facies reflects at least in part the same physical conditions of metamorphism as the increase in degree of coalification (rank) in the bituminous coal range. Degree of coalification is probably independent of partial pressures of H/sub 2/O and CO/sub 2/: it is controlled mainly by maximum depth of burial, its duration, and the geothermal gradient.

Characterization of uranium in bituminized radioactive waste drums by self-induced X-ray fluorescence

International Nuclear Information System (INIS)

Pin, Patrick; Perot, Bertrand

2013-06-01

This paper reports the experimental qualification of an original uranium characterization method based on fluorescence X rays induced by the spontaneous gamma emission of bituminized radioactive waste drums. The main 661.7 keV gamma ray following the 137 Cs decay produces by Compton scattering in the bituminized matrix an intense photon continuum around 100 keV, i.e. in the uranium X-ray fluorescence region. 'Self-induced' X-rays produced without using an external source allow a quantitative assessment of uranium as 137 Cs and uranium are homogeneously mixed and distributed in the bituminized matrix. The paper presents the experimental qualification of the method with real waste drums, showing a detection limit well below 1 kg of uranium in 20 min acquisitions while the usual gamma rays of 235 U (185 keV) or 238 U (1001 keV of 234m Pa in the radioactive decay chain) are not detected. The relative uncertainty on the uranium mass assessed by self-induced X-ray fluorescence (SXRF) is about 50%, with a 95% confidence level, taking into account the correction of photon attenuation in the waste matrix. This last indeed contains high atomic numbers elements like uranium, but also barium, in quantities which are not known for each drum. Attenuation is estimated thanks to the peak-to-Compton ratio to limit the corresponding uncertainty. The SXRF uranium masses measured in the real drums are in good agreement with long gamma-ray spectroscopy measurements (1001 keV peak) or with radiochemical analyses. (authors)

Evaluation of bituminous sub-ballast manufactured at low temperatures as an alternative for the construction of more sustainable railway structures

Directory of Open Access Journals (Sweden)

L. Pirozzolo

2017-07-01

Full Text Available Hot bituminous mixtures are becoming widely used in modern railway tracks in the sub-ballast layer. The reason is that these materials allow for both an increase in bearing capacity and greater protection of the substructure respect the traditional granular sub-ballast. Despite these advantages, the fact that these materials are manufactured at a temperature of 160°C means that their application can lead to an important increase in construction costs, pollution and energy consumption. This paper aims to study the possibility of using WMA manufactured at lower temperatures, as bituminous sub-ballast, in order to save energy and reduce emissions throughout the production process, as well as diminish the global costs of this layer. To this end, this study focuses on a comparison of the mechanical behaviour of warm and hot bituminous mixtures as sub-ballast under various loading conditions. The results indicate that WMA offers mechanical behaviour that is comparable to conventional HMA.

Process for treating bituminous coal, lignite, peat, and shale, and products obtained

Energy Technology Data Exchange (ETDEWEB)

Schabelitz, E J

1951-06-27

A process is described comprising leaching bituminous coal, lignite, peat, or shale by immersing said material in ethylene dichloride for a period of time sufficient to remove the ethylene dichloride-soluble constituents, separating the treated material from the ethylene dichloride solution and recovering from the solution the soluble constituents of the material dissolved in the solution. Soluble constituents include oils and waxes.

Chemical activation of bituminous coal for hampering oligomerization of organic contaminants.

Science.gov (United States)

Yan, Liang; Sorial, George A

2011-12-15

Activated carbons prepared by KOH activation of bituminous coal were studied for hampering oligomerization of phenolic compounds on its surface. A total of 24 activated carbons with different microporosity and BET surface area were created. The effect of the different variables of the activation process (KOH/bituminous coal ratio, heating temperature, activation time, and flow rate of nitrogen gas) on critical carbon parameters was analyzed. The impact of activated carbon on oligomerization was examined by conducting isotherm experiments at a neutral pH on Carbon(exp) produced with optimal characteristics and granular activated carbon (GAC) F400 for phenol, 2-methylphenol and 2-ethylphenol. These isotherms were collected under anoxic (absence of molecular oxygen) and oxic (presence of molecular oxygen) conditions. The single solute adsorption of phenol, 2-methylphenol and 2-ethylphenol on Carbon(exp) showed no obvious differences between oxic and anoxic environment, which indicated that the Carbon(exp) sample is very effective in hampering the oligomerization of phenolic compounds under oxic conditions. On the other hand, F400, which have lower micropore percentage and BET surface area, significant increases in the adsorptive capacity had been observed when molecular oxygen was present. Copyright © 2011 Elsevier B.V. All rights reserved.

Clay 2001 dossier: progress report on feasibility studies and research into deep geological disposal of high-level, long-lived waste; Dossier 2001 argile: sur l'avancement des etudes et recherches relatives a la faisabilite d'un stockage de dechets a haute activite et a vie longue en formation geologique profonde

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-12-01

A French Act of Parliament passed on 30 December 1991 set out the main areas of research required to prepare solutions for the long-term management of high-level, long-lived radioactive waste. The three avenues of research listed in the Act included a feasibility study of the deep geological disposal of these waste, with responsibility for steering the study given to ANDRA, France National Agency for Radioactive Waste Management. Following government decisions taken in 1998, the study focused on two types of geological medium, clay and granite. The clay formations study is essentially based on results from an underground laboratory sited at the border between the Meuse and Haute-Marne departments, where the Callovo-Oxfordian argillite beds are being investigated. No site has yet been chosen for an underground laboratory for the granite study, so for the time being this will draw on generic work and on research carried out in laboratories outside France. ANDRA has decided to present an initial report on the results of its research programme, publishing a dossier on the work on clay formations in 2001 with a second dossier covering the work on granite due for release in 2002. This dossier is thus a review of the work carried out by ANDRA on the feasibility study into a radioactive waste repository in a clay formation. It represents one step in a process of studies and research work leading up to the submission of a report due in 2005 containing ANDRA conclusions on the feasibility of a repository in the clay formation. (author)

On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

NARCIS (Netherlands)

Fischer, H.R.; Dillingh, E.C.; Hermse, C.G.M.

2013-01-01

The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in

The bituminization of intermediate level liquid radioactive wastes at Eurochemic. Part 3

International Nuclear Information System (INIS)

Demonie, M.; Hild, W.; Kokkelenberg, F.; Kretschmer, H.

1980-10-01

After 5.050 hours of operation, the screw elements of the extruder evaporator in the bituminization plant have been exchanged for elements with a higher abrasion resistance. The report describes the various working phases that have led, within ten weeks, to a successful accomplishment, and gives details on the required manpower, the total dose commitment, the wastes produced, and the wear of the extruder screw elements. (author)

Analysis of the sensitivity of the impact resonance frequency test as a tool to determine the elastic properties of bituminous materials

Directory of Open Access Journals (Sweden)

R. Tauste

2017-07-01

Full Text Available The modulus value of bituminous materials is a key factor in the design of road pavements and the estimation of their life service. This parameter can be measured in laboratory but, unfortunately, this requires the deterioration of the pavement so as the consumption of time and resources. Therefore, this study analyses the feasibility of using impact resonance frequency tests as an alternative to traditional methods for determining the dynamic modulus of bituminous mixtures. The sensitivity of this technique has been studied by analyzing its repeatability and reproducibility, studying the variations in the values measured by modifying the dimensions of the specimens, test temperatures and types of mixture tested. In addition, this non-destructive technique has been compared with other traditional tests used to determine the elastic properties of bituminous materials. The results show that this test could be an interesting tool to characterize the properties and damage state of asphalt layers.

Analysis of the sensitivity of the impact resonance frequency test as a tool to determine the elastic properties of bituminous materials

International Nuclear Information System (INIS)

Tauste, R.; Moreno-Navarro, F.; Gallego, R.; Rubio-Gámez, M.C.

2017-01-01

The modulus value of bituminous materials is a key factor in the design of road pavements and the estimation of their life service. This parameter can be measured in laboratory but, unfortunately, this requires the deterioration of the pavement so as the consumption of time and resources. Therefore, this study analyses the feasibility of using impact resonance frequency tests as an alternative to traditional methods for determining the dynamic modulus of bituminous mixtures. The sensitivity of this technique has been studied by analyzing its repeatability and reproducibility, studying the variations in the values measured by modifying the dimensions of the specimens, test temperatures and types of mixture tested. In addition, this non-destructive technique has been compared with other traditional tests used to determine the elastic properties of bituminous materials. The results show that this test could be an interesting tool to characterize the properties and damage state of asphalt layers. [es

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

Energy Technology Data Exchange (ETDEWEB)

Anthonissen, Joke, E-mail: joke.anthonissen@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Van den bergh, Wim, E-mail: wim.vandenbergh@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Braet, Johan, E-mail: johan.braet@uantwerpen.be [Department Engineering Management, Faculty of Applied Economics, University of Antwerp, Prinsstraat 13, 2000 Antwerp (Belgium)

2016-09-15

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

International Nuclear Information System (INIS)

Anthonissen, Joke; Van den bergh, Wim; Braet, Johan

2016-01-01

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

Relation between particle size and properties of some bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Palmer, A.D.; Cheng, M.; Goulet, J.-C.; Furimsky, E. (CANMET, Ottawa, ON (Canada). Energy Research Laboratories)

1990-02-01

Coal fractions of different size distributions exhibited different H/C ratio, ash and sulphur contents, and surface structures. This was confirmed using two low-sulphur and two high-sulphur bituminous coals. The effect was much less pronounced for low-sulphur coals than for high-sulphur coals. A significant difference in properties was noted between the two high-sulphur coals in spite of similar basic compositional parameters. This was confirmed by the fractal dimensionality factor D of Illinois No. 6 coal, which exceeded the theoretical value. 14 refs., 9 figs., 5 tabs.

Utilization of Waste Clay from Boron Production in Bituminous Geosynthetic Barrier (GBR-B Production as Landfill Liner

Directory of Open Access Journals (Sweden)

Müfide Banar

2016-01-01

Full Text Available Bituminous geomembranes, one type of geosynthetics, include a hot bituminous mixture with mineral filler and reinforcement. In this study, boron production waste clay (CW was used as filler to produce a geosynthetic barrier with bentonite, waste tire, and bitumen. Bentonite and waste tires were used as auxiliary fillers and bitumen as the binder. CW/bitumen, CW/bentonite/bitumen, and CW/waste tire/bitumen mixtures were prepared by using a laboratory mixer at 100°C. Hot mixtures were extruded into strips by using a lab-scale corotating twin screw extruder (L/D: 40 followed by die casting (2 mm × 100 mm. Glass fleece or nonwoven polyester was used as reinforcement material and while die casting, both sides of the reinforcement materials were covered with bituminous mixture. Thickness, mass per unit area, tensile strength, elongation at yield, and hydraulic conductivity were used to characterize the geomembranes. Among all geomembranes, nonwoven polyester covered with 30% bitumen-70% boron waste clay mixture (PK-BTM30CW70 was found to be the most promising in terms of structure and mechanical behaviour. After that, consequences of its exposure to distilled water (DW, municipal solid waste landfill leachate (L-MSW, and hazardous waste landfill leachate (L-HW were examined to use for an innovative impermeable liner on solid waste landfills.

The X-ray fluorescent method for determination of total sulphur in bituminous coals

International Nuclear Information System (INIS)

Widowska-Kusmierska, J.; Siess, K.

1979-01-01

The X-ray fluorescent technique for the determination of total sulphur covering concentrations from 0,1 to 10% has been applied for bituminous coals showing a great variability in qualitative and quantitative composition of mineral matter (ash). The described method is a quick one giving results during one hour. The obtained good accuracy of determinations gives prospects for wide industrial application. (author)

Isotopic variations in the nitrogen of natural humic and bituminous organic substances

International Nuclear Information System (INIS)

Stiehl, G.; Lehmann, M.

1980-01-01

delta 15 N-values and nitrogen contents of a series of humic and bituminous organic sediments of different ranks were determined. The change of the isotopic abundance of nitrogen was investigated during heating in model experiments, using a gas flame coal. In the case of humic carbon coals the relative nitrogen contents vary from 0.8 to 1.4% and the delta 15 N-values from + 3.5 to + 6.3 parts per thousand increasing from the brown coal to anthracite ranks. During the coalification process both the delta 15 N-values and the relative nitrogen contents do not vary continuously with the rank, but pass through maxima and minima. Model experiments using a gas flame coal show the same trend. Nitrogen with delta 15 N-values of + 2.8 or -7 parts per thousand was released in pyrolysis experiments, applying a gas flame coal and a steam coal at temperatures of 650 and 1000 0 C, respectively. The investigated bituminous sediments yielded relative amounts of 0.1 to 0.8% with delta 15 N-values of + 4.2 to + 10.7 parts per thousand. The obtained results are discussed with respect to the elucidation of nitrogen genesis in natural gas deposits. (author)

Process for continuous distillation of bituminous minerals, etc

Energy Technology Data Exchange (ETDEWEB)

Marie, J J

1923-01-26

An apparatus is described for operating the process, in which the petroleum-bearing asphaltic or bituminous minerals are charged to the upper part of a vertical furnace with a lining of refractory material and varying sections; air is necessary for combustion and inert gas is necessary to regulate this combustion and to remove the hydrocarbons being blown into the lower part of the furnace; the hydrocarbons in vapor state or gases being removed are received in the condensers where they are deposited in the liquid state; the liquid from the condensers is next centrifuged to give oils essentially like natural petroleum, leaving as residue solid hydrocarbons and entrained mineral; the minerals treated are removed by gravity at the bottom of the furnace.

THE HISTORY OF EXPLORATION AND EXPLOITATION OF BITUMINOUS AND KEROGENOUS DEPOSITS IN CROATIA

Directory of Open Access Journals (Sweden)

Berislav Šebečić

1995-12-01

Full Text Available It is assumed thal the first known sedimens of natural bitumen or asphalt in coastal Croatia were exploited as the early moddle ages. Yet authenticated written documents about Vinišće near Trogir derive from no earlier than 1628, about Vrgorac/Paklina from only 1753. By the end of the 18th century, many deposits were discovered in Dalmatia, but it was Škrip on the Island of Brač and Suhi Dolac that were important. The earliest known deposits and occurrences of kerogenous rocks, or bituminous or oil shales, are mentioned as stone or fossil coal in Sovinjak, in the upper course of the River Mirna, and in Rebići in Istria; near Sinj, Slivno not far from the River Neretva, Mirta and near Nerežišće on the Island uf Brač. All if these were well known and described in 1804, while Sovinjak was mentioned in the 16th century. In the article, some of new information derived from mining and geological research into bituminous and kerogenous sediments and deposits are provided (the paper is published in Croatian.

Process for carbonizing hard-to-heat bituminous material like shale

Energy Technology Data Exchange (ETDEWEB)

Nagel, K

1921-11-29

A process is described for carbonizing bituminous material, like shale, with the production of sufficient heat for carbonization by burning a part of the bitumen itself by means of a gas stream going in a circuit, to which oxygen in regulated amounts is admitted. It is characterized by the fact that the gas stream already cooled for detarring before its re-entrance into the carbonization chamber is mixed in the inlet channels with an amount of oxygen (air or other free oxygen containing gases), that without sintering or melting of the residue it is burned and the carbonization is carried out evenly.

Long-term properties of TVO's bituminized resins

International Nuclear Information System (INIS)

Valkiainen, M.; Vuorinen, U.

1989-06-01

Long-term properties of bituminized spent ion-exchange resins from Olkiluoto power plant have been studied since 1981. This report summarizes the results on water uptake and leaching obtained up till now. It is observed that water uptake in excess of rewetting of the ion-exchange resins is taking place. Leach test in water equilibrated with cement have been performed for about five years. Separation of granular resin particles caused by density differences observed in former experiments was further studied and confirmed in this work. Anaerobic corrosion of a steel drum has been studied in laboratory conditions generally giving corrosion rates below l μm/a. Radiolytic gases will accumulate and be trapped in the waste product. The rate of swelling is estimated by a specially constructed device based on ultrasonic distance meter observing changes in level of the product surface in the drum

Assessment of the Remaining Life of Bituminous Layers in Road Pavements

Directory of Open Access Journals (Sweden)

Kálmán Adorjányi

2017-02-01

Full Text Available In this paper, a mechanistic-empirical approach is presented for the assessment of bearing capacity condition of asphalt pavement layers by Falling Weight Deflectometer measurements and laboratory fatigue tests. The bearing capacity condition ratio was determined using past traffic data and the remaining fatigue life which was determined from multilayer pavement response model. The traffic growth rate was taken into account with finite arithmetic and geometric progressions. Fatigue resistance of layers’ bituminous materials was obtained with indirect tensile fatigue tests. Deduct curve of condition scores was derived with Weibull distribution.

Assessing radioactive concentrates and waste vapor condensate in solidifying radioactive wastes by bituminization

International Nuclear Information System (INIS)

Tibensky, L.; Krejci, F.; Breza, M.; Timulak, J.; Hladky, E.

1986-01-01

A brief overview is presented of chemical and radiochemical methods used in the world for the analysis of the concentrate of liquid radioactive wastes from nuclear power plants destined for bituminization. Most methods are also suitable for an analysis of the condensate of waste vapors produced in bituminization. The methods of analysis of the radioactive concentrate from the V-1 nuclear power plant in Jaslovske Bohunice and of the waste vapors condensate were developed and tested in practice. Gross gamma activity was measured using a well-type Na(Tl) scintillation detector, the content of radionuclides was determined using semiconductor Ge(Li) spectrometry. The concentration of boric acid in the concentrate was determined by titration with mannite; in the condensate, using spectrophotometry with curcumine. The content of nitrates in both the concentrate and the condensate was determined spectrophotometrically using salicylic acid, the content of nitrites was determined by spectrophotometry using sulfanilic acid and α-naphthylamine. Carbonates and chlorides were determined by titration, sodium and potassium by flame photometry. The content of organic acids was measured by gravimetry of extracted methyl esters, the content of surfactants by spectrophotometry. Infrared spectrophotometry was used in determining hydrocarbons in the waste vapor condensate. The measured value range and the measurement errors are shown for each method. (A.K.)

Mechanical properties of hot bituminous mixes manufactured with recycled aggregate of Silestone® waste

Directory of Open Access Journals (Sweden)

Rubio, M. C.

2011-03-01

Full Text Available This article presents the results of a research project which analyzes the viability of incorporating waste material from decorative quartz solid surfacing in the manufacture of hot bituminous mixes. For this purpose, various bituminous mixes were manufactured with waste aggregate in different percentage. A set of tests were carried out that permitted the characterization of the mechanical behavior of these mixes. The results of these tests were similar to the results obtained when conventional mixes made from virgin quarry aggregate were tested. The results for moisture sensitivity as well as for wheel track rutting on mixes showed the optimal performance of this waste material even under very demanding traffic conditions. Laboratory studies showed that the use of this waste material in the manufacture of bituminous mixes is technically viable and can provide high-quality recycled aggregates at a very low cost, which can be used in the pavement of road.

Este artículo muestra los resultados de un proyecto de investigación que tiene por objeto analizar la viabilidad de incorporación de residuos procedentes de piedra decorativa en la fabricación de mezclas bituminosas en caliente. Para ello se fabricaron mezclas con áridos reciclados de residuos procedentes de piedra decorativa en distintos porcentajes, realizando un conjunto de ensayos que posibilitaron caracterizar el comportamiento mecánico de dichas mezclas. Los resultados obtenidos fueron similares a los de las mezclas convencionales fabricadas con áridos vírgenes procedentes de cantera. Los valores de resistencia conservada ante la acción del agua y deformación en pista, pusieron de manifiesto la aptitud del residuo incluso ante las condiciones de tráfico más exigentes. Los trabajos realizados en el laboratorio indican que la utilización del residuo en la fabricación de mezclas bituminosas es técnicamente viable, pudiendo obtenerse áridos reciclados de gran calidad y

Challenges for the registration of vaccines in emerging countries: Differences in dossier requirements, application and evaluation processes.

Science.gov (United States)

Dellepiane, Nora; Pagliusi, Sonia

2018-06-07

The divergence of regulatory requirements and processes in developing and emerging countries contributes to hamper vaccines' registration, and therefore delay access to high-quality, safe and efficacious vaccines for their respective populations. This report focuses on providing insights on the heterogeneity of registration requirements in terms of numbering structure and overall content of dossiers for marketing authorisation applications for vaccines in different areas of the world. While it also illustrates the divergence of regulatory processes in general, as well as the need to avoid redundant reviews, it does not claim to provide a comprehensive view of all processes nor existing facilitating mechanisms, nor is it intended to touch upon the differences in assessments made by different regulatory authorities. This report describes the work analysed by regulatory experts from vaccine manufacturing companies during a meeting held in Geneva in May 2017, in identifying and quantifying differences in the requirements for vaccine registration in three aspects for comparison: the dossier numbering structure and contents, the application forms, and the evaluation procedures, in different countries and regions. The Module 1 of the Common Technical Document (CTD) of 10 countries were compared. Modules 2-5 of the CTDs of two regions and three countries were compared to the CTD of the US FDA. The application forms of eight countries were compared and the registration procedures of 134 importing countries were compared as well. The analysis indicates a high degree of divergence in numbering structure and content requirements. Possible interventions that would lead to significant improvements in registration efficiency include alignment in CTD numbering structure, a standardised model-application form, and better convergence of evaluation procedures. Copyright © 2018.

Études des pratiques funéraires éthiopiennes : contextes, sources et enjeux. Introduction au dossier

Directory of Open Access Journals (Sweden)

Anaïs Wion

2012-01-01

Full Text Available Ce dossier rassemble des articles issus d’un séminaire de recherche sur la mort et les funérailles en Éthiopie qui a eu lieu entre 2002 et 2004 au Centre de recherches africaines de l’Université Paris 1 Panthéon-Sorbonne, animé par les enseignants-chercheurs, chercheurs, doctorants et post-doctorants travaillant sur l’Éthiopie. Ce séminaire se voulait délibérément ouvert aux différentes périodes, aux disciplines, aux aires culturelles qui recouvrent l’espace éthiopien d’aujourd’hui, même si l...

Experimental and computational study and development of the bituminous coal entrained-flow air-blown gasifier for IGCC

International Nuclear Information System (INIS)

Abaimov, N A; Osipov, P V; Ryzhkov, A F

2016-01-01

In the paper the development of the advanced bituminous coal entrained-flow air- blown gasifier for the high power integrated gasification combined cycle is considered. The computational fluid dynamics technique is used as the basic development tool. The experiment on the pressurized entrained-flow gasifier was performed by “NPO CKTI” JSC for the thermochemical processes submodel verification. The kinetic constants for Kuznetsk bituminous coal (flame coal), obtained by thermal gravimetric analysis method, are used in the model. The calculation results obtained by the CFD model are in satisfactory agreements with experimental data. On the basis of the verified model the advanced gasifier structure was suggested which permits to increase the hydrogen content in the synthesis gas and consequently to improve the gas turbine efficiency. In order to meet the specified requirements vapor is added on the second stage of MHI type gasifier and heat necessary for air gasification is compensated by supplemental heating of the blasting air. (paper)

Method of distillation of bituminous material

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, E G.T.

1919-11-12

A method is described of dry distillation of bituminous materials by leading warm combustible gases, mixed or not mixed with steam, through the distillation chamber in direct contact with the materials, during which process the distillation chamber may be heated by other means. It is characterized by the mixture of distillation products (formed by the vapors produced by heating the raw materials) and the gas (circulating gas) used for heating in the process, being led through coolers or similar contrivances, in order to separate through condensation the greater part of the content of the products or materials condensable at ordinary temperatures, and also to recover as much as possible of the highly volatile oils in the gas. Thereafter the gas is split, one part is, without further cleaning, and led through the distillation chamber, after this gas has been reheated in suitable apparatus. The other part (surplus gas), which in volume corresponds approximately to the new-formed distillation gases, is treated according to known methods for the extraction of the remaining products of the distillation, such as volatile oils, ammonia, methyl alcohol, sulfuretted hydrogen, and others. The patent contains three other claims.

Cause finding experiments and environmental analysis on the accident of the fire and explosion in TRP bituminization facility

International Nuclear Information System (INIS)

Fujine, Sachio; Murata, Mikio; Abe, Hitoshi

1999-09-01

This report is the summary of the cause finding experiments and environmental analysis on the accident of the fire and explosion occurred at March 11th, 1997, in TRP bituminization facility of PNC (Power Reactor and Nuclear Fuel Development Corporation). Regarding the cause finding experiments, chemical components have been analyzed for the effluent samples taken from PNC's facility, bituminized mock waste has been produced using the simulated salt effluent prepared according to the results of chemical analysis, thermal analysis and experiment of runaway exothermic reaction have been conducted using the mock waste, and the component of flammable gases emitted from the heated waste have been collected and analyzed. Regarding environmental analysis on the accident, the amount of radioactive cesium released by the accident has been calculated by the comparative analysis using the atmospheric dispersion simulation code SPEEDI with the data of environmental monitoring and the public dose has been assessed. (author)

Application of the cementitious grouts on stability and durability of semi flexible bituminous mixtures

Science.gov (United States)

Karami, Muhammad

2017-11-01

This paper describes the results of laboratory test for a high durability semi flexible bituminous mixtures (SFBM). The SFBM consists of an open asphalt structure where a high strength mortar is penetrated into the air voids of the bituminous mixtures. The SFBM combines the cement concrete's strength and the asphalt material flexibility. The objective of this study is to involve in the determination of stability and durability of SFBM by located the position of the specimen on an exposed area for 7, 90, 180 and 240 days. The performance of the SFBM was assessed using Marshall and wheel tracking apparatus. Total 18 specimens were prepared and examined for both of test. The Marshall specimens were cylindrical with dimension of 10.16 cm in diameter and 6.35 cm in high. For wheel tracking test, the specimens consisted of slabs with dimension of 30 cm in length, 30 cm in width and 5 cm in height. The results indicated that the first durability index and second durability index increased significantly. For Marshall test, the first and second durability index increased about 0.9% per day and 52.3%, respectively. However, for wheel tracking test, the first and second durability index increased about 1.9% per day and 119%, respectively.

Energy press kit; Dossier energie

Energy Technology Data Exchange (ETDEWEB)

Czarnes, R.; Chauvot, M.; Depagneux, M.A.; Bollack, L.; Cittanova, M.L.; Madelaine, N.; Alves, J.; Burg, D

2004-06-01

This special dossier treats of the changes that will happen in France with the deregulation of energy markets. It comprises 19 articles dealing with: the big bang of July 1, 2004 in the electricity and gas sector (on July 1, 2004, all professional consumers will have the possibility to chose their electricity and gas supplier. If Electricite de France (EdF) and Gaz de France (GdF) monopolies will split up, several questions remain unanswered for clients); the impossible penetration of the French market (3 weeks before the enhanced opening of power markets, EdF's competitors remain surprisingly limited and are mainly French actors. The big European competitors follow a wait-and-see policy); the independent power producer Compagnie Generale du Rhone wants to diversify its clients and is looking towards local authorities; Direct Energie: the 'low-cost' company for the mutualization of electricity purchases of small professionals; Endesa, the French daughter company of the Spanish electric utility, is looking for a balance between production and sales; HEW, daughter company of Vattenfall Europe and present in France since April 2000, wants to increase its margins more than its capacity; energy profilers are making consumption profiles for EdF's competitors; Poweo, energy retailing company built in 2002, is fetching very small companies; Atel, French daughter company of the Swiss power producer, does not foresee important changes in July 1; interview of F. Roussely, head of EdF about the liberalization of the electricity sector; the main energy groups favorable to deregulation; case study: Accor, the hotel trade group, has chosen Compagnie Generale du Rhone as power supplier; electricity: why prices are increasing; various foreign experiences; UK: the consolidation time (fully liberalized and privatized between several companies, the British energy market is under total re-building); USA: the deregulation process has failed and stays stuck to 24

Process of extraction in liquid way, of the bitumen from asphaltic and bituminous rocks, shale, etc

Energy Technology Data Exchange (ETDEWEB)

Freda, L

1936-06-04

A process is described for liquid extraction of the bitumen in asphaltic and bituminous rocks, shales, and the like. The substances impregnated with bitumen are suitably treated for the extraction of pitch with any given solvent derived from ethylene, in a series of apparatuses fixed and rotary at atmospheric pressure or in vacuum with vapor and hot air.

Effect of organic calcium compounds on combustion characteristics of rice husk, sewage sludge, and bituminous coal: thermogravimetric investigation.

Science.gov (United States)

Zhang, Lihui; Duan, Feng; Huang, Yaji

2015-04-01

Experiments were conducted in a thermogravimetric analyzer to assess the enhancement of combustion characteristics of different solid fuels blended with organic calcium compounds (OCCs). Rice husk, sewage sludge, and bituminous coal, and two OCC were used in this study. Effect of different mole ratios of calcium to sulfur (Ca/S ratio) on the combustion characteristics were also investigated. Results indicated that combustion performance indexes for bituminous coal impregnated by OCC were improved, however, an inverse trend was found for sewage sludge because sewage sludge has lower ignition temperature and higher volatile matter content compared to those of OCC. For rice husk, effect of added OCC on the combustion characteristics is not obvious. Different solid fuels show different combustion characteristics with increases of Ca/S ratio. The maximum combustion performance indexes appear at Ca/S ratios of 1:1, 2:1, and 3:1 for OCC blended with Shenhua coal, rice husk, and sewage sludge, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Study of thermal reactivity during bituminization of radioactive waste

International Nuclear Information System (INIS)

Mouffe, Sh.

2004-10-01

This work deals with the study of chemical reactions and phases transitions which can occur between magnesium nitrate, sodium nitrate, cobalt sulphur product, and nickel potassium ferrocyanide, when they are heated together during bituminization process of nuclear waste. The applied methodology associates a few techniques: temperature, enthalpy, and kinetics of reaction are determined by calorimetry, reaction products are characterised by chemical analyses, mass spectrometry and XRD analysis. Three fields of temperature and energy are observed in function of composition (one compound or a mixture of compounds). The study of reactions between NaNO 3 and cobalt sulphur product shows that the presence of water has got an effect on reaction temperature. The study of Mg(NO 3 ) 2 , 6 H 2 O and CoS shows an overlapping of different signals, and that the reaction rate is very slow (a few hours). (author)

Environmental problems caused by bituminous schist and possible solutions

International Nuclear Information System (INIS)

Elmas, N.; Aykul, H.; Erarslan, K.; Ediz, I.G.

1998-01-01

Schist, as a disposal of mine, has harmful effects on environment. however, several manners can be utilized to prevent the environmental destruction as well as an economical benefit is gained. In this study, environmental problems caused by bituminous schist and other disposals have been investigated on a specific lignite coal mine where schist is disposed as waste material. Pollution and damage on land and in water sources around the coal district and the villages have been observed, recorded and several solutions to environmental problems have been proposed. Discussed proposals will not only solve the environmental pollution problem but also provide waste management facility. Industrial structure of the district enables such a disposal to be used as an economical raw material. Besides, general effects of the coal mine and the power plant nearby have been discussed from environmental point of view, too. 7 refs

Process of heat-treating fuels of a bituminous nature, such as shale

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1927-11-25

A process is described of heat treating any kind of material of a bituminous nature usable as fuel, like shale, mineral coal, peat, etc., whereby the fuel undergoes in a retort or the like a distillation for recovering from it the total amount or the greatest part of gaseous or vaporous distillation products. The warm distillation residue is burned, characterized by the retorts, containing the fuel going through, being wholly or partly surrounded by materials to be heated. These materials and the warm distillation residue resulting from the distillation during the burning are moved forward independently one of the other.

Organic petrology and geochemistry of Eocene Suzak bituminous marl, north-central Afghanistan: Depositional environment and source rock potential

Science.gov (United States)

Hackley, Paul C.; Sanfilipo, John

2016-01-01

Organic geochemistry and petrology of Eocene Suzak bituminous marl outcrop samples from Madr village in north-central Afghanistan were characterized via an integrated analytical approach to evaluate depositional environment and source rock potential. Multiple proxies suggest the organic-rich (TOC ∼6 wt.%) bituminous marls are ‘immature’ for oil generation (e.g., vitrinite Ro  1) indicating organic input from marine algae and/or bacterial biomass, and sterane/hopane ratios are low (0.12–0.14). Monoaromatic steroids are dominated by C28clearly indicating a marine setting. High gammacerane index values (∼0.9) are consistent with anoxia stratification and may indicate intermittent saline-hypersaline conditions. Stable C isotope ratios also suggest a marine depositional scenario for the Suzak samples, consistent with the presence of marine foraminifera including abundant planktic globigerinida(?) and rare benthic discocyclina(?) and nummulites(?). Biomarker 2α-methylhopane for photosynthetic cyanobacteria implies shallow photic zone deposition of Madr marls and 3β-methylhopane indicates presence of methanotrophic archaea in the microbial consortium. The data presented herein are consistent with deposition of Suzak bituminous marls in shallow stratified waters of a restricted marine basin associated with the southeastern incipient or proto-Paratethys. Geochemical proxies from Suzak rock extracts (S content, high polar content, C isotopes, normal (αααR) C27–29 steranes, and C29/C30 and C26/C25 hopane ratios) are similar to extant data from Paleogene oils produced to the north in the Afghan-Tajik Basin. This observation may indicate laterally equivalent strata are effective source rocks as suggested by previous workers; however, further work is needed to strengthen oil-source correlations.

Swelling behavior of several bituminous coals and their thermally treated coals

Energy Technology Data Exchange (ETDEWEB)

Shui, Heng-fu; Cao, Mei-xia; Wang, Zhi-cai [Anhui University of Technology, Maanshan (China). School of Chemistry & Chemical Engineering

2007-07-01

The swelling behavior in different solvents of 4 bituminous coals with different ranks and their residues from extraction by CS{sub 2}/NMP mixed solvent (l:1 in volume) were measured. The change in swelling property of the four coals thermally treated at different temperature was observed. The results show that the swelling ratio decreases with increasing rank of coal. For lower rank bituminous coals the swelling ratios in polar solvent are higher than those in non-polar solvent, and this difference decreases with increasing rank. The cross-linking densities of the four residues decrease, and the swelling ratios increase compared with those of raw coals. The swelling ratios of the four thermally treated coals under 150{sup o}C in CS{sub 2} increase, suggesting the decrease in crosslinking density of them. When the thermal treatment temperature increases to 240{sup o}C, the swelling rations of the other three coals in NMP and CS{sub 2} increase again except gas coal, demonstrating the further decrease in crosslinking density. This result is coincident with the extraction yield change in the mixed solvent of the thermally treated coal. For example, the extraction yield of lean coal treated at 240{sup o}C increases from 6.9% to 17.3%. FT-IR results show the removal of oxygen group of the thermally treated coals. This may explain the increase in swelling ratio and extraction yield in the mixed solvent of coal after thermal treatment. The cross-linking density of the thermally treated coal decreases because of the break of hydrogen bonds due to removal of C = 0 and -OH oxygen groups during the thermal treatment, resulting in the increases of swelling ratio and extraction yield in the mixed solvent of thermally treated coal compared with those of raw coal. 15 refs., 3 figs., 6 tabs.

En diálogo con los artículos del dossier psicoanálisis y filosofía. ¿Hay un diálogo posible?/In dialogue with the articles of dossier psychoanalysis and phylosophy. Is there a possible dialogue?

Directory of Open Access Journals (Sweden)

Ana María Fernández

2010-03-01

Full Text Available A partir de la pregunta que anima este número de la revista ¿hay un diálogo posible entre el psicoanálisis y la filosofía? el presente artículo tiene como cometido realizar un dialogo con algunos autores del Dossier, tomando como punto de referencia los trabajos en los cuales está presente cierta problematización del psicoanálisis a través de los trabajos de Foucault. The main question that brings about this new issue of the Journal is about the possible or impossible dialog between psychoanalysis and philosophy. Particularly, this article considers author contributions to this issue challenging psychoanalysis through the lens of Foucauldian theory.

Reducing the emissions of nitrogen oxides when burning Kuznetsk bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Kotler, V.R.

1983-02-01

Bituminous coals from the Kuzbass have a high nitrogen content. As a result, emissions of NO/SUB/x from power stations burning these coals frequently exceed the existing Standard. In order to reduce NO/SUB/x emissions tests were carried out using stage-wise combustion, supplying to the burners only part of the air required for complete combustion. The remaining air is supplied via tertiary nozzles situated about 14 m above the burners. As a result of the tests, this method of combustion is recommended for low-sulphur Kuznetsk coals for all sub-critical boilers having dry-bottom furnaces. Extension to boilers with wet-bottom furnaces and to supercritical boilers requires further investigation.

Extraction d'association d'EIM à partir de dossiers patients : expérimentation avec les structures de patrons et les ontologies

OpenAIRE

Personeni , Gabin; Devignes , Marie-Dominique; Dumontier , Michel; Smaïl-Tabbone , Malika; Coulet , Adrien

2016-01-01

National audience; Les Dossiers Médicaux Electroniques (DME) constituent une ressource de grand intérêt pour étudier les Evènements Indésirables Médicamenteux (EIM). Nous proposons ici de fouiller les DME pour identifier des EIM fréquemment associés dans des sous-groupes de patients. Les EIM ayant des manifestations complexes, nous utilisons l'analyse formelle de concepts et ses structures de patrons, un cadre mathématique permettant la généralisation, en exploitant les connaissances du domai...

Nagra technical report 14-02, Geological basics - Dossier VI - Barrier properties of proposed host rock sediments and neighbouring rock

International Nuclear Information System (INIS)

Gautschi, A.; Deplazes, G.; Traber, D.; Marschall, P.; Mazurek, M.; Gimmi, T.; Maeder, U.

2014-01-01

This dossier is the sixth of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It discusses the barrier properties of the proposed host rock sediments and neighbouring rock layers. The mineralogical composition of the host rocks are discussed as are their pore densities and hydrological properties. Diffusion aspects are discussed. The aquifer systems in the proposed depository areas and their classification are looked at. The barrier properties of the host rocks and those of neighbouring sediments are discussed. Finally, modelling concepts and parameters for the transport of radionuclides in the rocks are discussed

Advances in Interlaboratory Testing and Evaluation of Bituminous Materials State-of-the-Art Report of the RILEM Technical Committee 206-ATB

CERN Document Server

Bahia, Hussain; Canestrari, Francesco; Roche, Chantal; Benedetto, Hervé; Piber, Herald; Sybilski, Dariusz

2013-01-01

This STAR on asphalt materials presents the achievements of RILEM TC 206 ATB, acquired over many years of interlaboratory tests and international knowledge exchange. It covers experimental aspects of bituminous binder fatigue testing; the background on compaction methods and imaging techniques for characterizing asphalt mixtures including validation of a new imaging software; it focuses on experimental questions and analysis tools regarding mechanical wheel tracking tests, comparing results from different labs and using finite element techniques. Furthermore, long-term rutting prediction and evaluation for an Austrian road are discussed, followed by an extensive analysis and test program on interlayer bond testing of three different test sections which were specifically constructed for this purpose. Finally, the key issue of manufacturing reclaimed hot mix asphalt in the laboratory is studied and recommendations for laboratory ageing of bituminous mixtures are given.

Influence of metal additives on pyrolysis behavior of bituminous coal by TG-FTIR analysis

Energy Technology Data Exchange (ETDEWEB)

Su, Wenjuan; Fang, Mengxiang; Cen, Jianmeng; Li, Chao; Luo, Zhongyang; Cen, Kefa [Zhejiang Univ., Hangzhou (China). State Key Lab. of Clean Energy Utilization

2013-07-01

To study the catalytic effects of alkali, alkaline earth and transition metal additives on coal pyrolysis behavior, bituminous coal loaded NaCl, KCl, CaCl{sub 2}, MgCl{sub 2}, FeCl{sub 3} and NiCl{sub 2} was respectively investigated using Thermogravimetry and Fourier Transform Infrared Spectroscopy (TG-FTIR). Results indicated that the maximum mass loss rate decreased under the metal additives in the primary pyrolysis stage. The total mass loss of pyrolysis was reduced in metals catalyzed pyrolysis except for Na loaded sample. Kinetic analysis was taken for all samples adopting the method of Coats-Redfern. Activation energy of raw coal in the primary pyrolysis stage was 92.15vkJ.mol{sup -1}, which was lowered to 44.59-73.42 kJ.mol{sup -1} under metal additives. The orders of catalytic effect for this bituminous coal were Mg > Fe > Ca > Ni > K > Na according to their activation energies. Several investigated volatiles including CH{sub 4}, CO{sub 2}, CO, toluene, phenol and formic acid were identified from FTIR spectra. The yields of CH{sub 4}, CO{sub 2}, toluene, phenol and formic acid were decreased, but the evolution of CO was increased. The presence of metals in the coal samples have been involved in a repeated bond-forming and bond-breaking process, which greatly hindered the release of tars during pyrolysis as the tar precursors were connected to coal/char matrix and were thermally cracked, becoming a part of char.

High temperature solvent extraction of oil shale and bituminous coal using binary solvent mixtures

Energy Technology Data Exchange (ETDEWEB)

Goetz, G.K.E. [Lehrstuhl fuer Geologie, Geochemie und Lagerstaetten des Erdoels und der Kohle, RWTH Aachen (Germany)

1997-12-31

A high volatile bituminous coal from the Saar Basin and an oil shale from the Messel deposit, both Germany, were extracted with binary solvent mixtures using the Advanced Solvent Extraction method (ASE). Extraction temperature and pressure were kept at 100 C, respectively 150 C, and 20,7 MPa. After the heating phase (5 min) static extractions were performed with mixtures (v:v, 1:3) of methanol with toluene, respectively trichloromethane, for further 5 min. Extract yields were the same or on a higher level compared to those from classical soxhlet extractions (3 days) using the same solvents at 60 C. Comparing the results from ASE with those from supercritical fluid extraction (SFE) the extract yields were similar. Increasing the temperature in ASE releases more soluble organic matter from geological samples, because compounds with higher molecular weight and especially more polar substances were solubilized. But also an enhanced extraction efficiency resulted for aliphatic and aromatic hydrocarbons which are used as biomarkers in Organic Geochemistry. Application of thermochemolysis with tetraethylammonium hydroxide (TEAH) using pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) on the extraction residues shows clearly that at higher extraction temperatures minor amounts of free fatty acids or their methyl esters (original or produced by ASE) were trapped inside the pore systems of the oil shale or the bituminous coal. ASE offers a rapid and very efficient extraction method for geological samples reducing analysis time and costs for solvents. (orig.)

Method of simultaneous recovery of oil and sulfur from bituminous shales

Energy Technology Data Exchange (ETDEWEB)

1919-02-25

The method consists of means for dry distillation of bituminous shales in furnaces heated from inside to recover simultaneously oil and sulfur, and is characterized by obtaining the sulfur partly in the form of sulfuretted hydrogen as a direct distillation product produced in the upper part of the furnace and partly in the form of free sulfur formed in the reduction zone of the furnace by the reduction of the sulfur dioxide formed in the burning zone. It is also characterized by the recovery of sulfur--in so far as the reduction and formation of sulfur dioxide are concerned--being regulated by means of the corresponding regulation of the proportion of the speed of discharging to the amount of air introduced into the process.

Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

Directory of Open Access Journals (Sweden)

Cieślik Ewelina

2018-01-01

Full Text Available One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

Science.gov (United States)

Cieślik, Ewelina; Konieczny, Tomasz; Bobik, Bartłomiej

2018-01-01

One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction) were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

Natural gas storage with activated carbon from a bituminous coal

Science.gov (United States)

Sun, Jielun; Rood, M.J.; Rostam-Abadi, M.; Lizzio, A.A.

1996-01-01

Granular activated carbons ( -20 + 100 mesh; 0.149-0.84 mm) were produced by physical activation and chemical activation with KOH from an Illinois bituminous coal (IBC-106) for natural gas storage. The products were characterized by BET surface area, micropore volume, bulk density, and methane adsorption capacities. Volumetric methane adsorption capacities (Vm/Vs) of some of the granular carbons produced by physical activation are about 70 cm3/cm3 which is comparable to that of BPL, a commercial activated carbon. Vm/Vs values above 100 cm3/cm3 are obtainable by grinding the granular products to - 325 mesh (activated carbons, granular carbons produced by KOH activation have higher micropore volume and higher methane adsorption capacities (g/g). Their volumetric methane adsorption capacities are lower due to their lower bulk densities. Copyright ?? 1996 Elsevier Science Ltd.

Study of bituminous surface treatments in Virginia : Phase II, Summer, 1964 : Distribution characteristics of materials, effectiveness of one size aggregate, setting time.

Science.gov (United States)

1970-01-01

Distribution Characteristics of Materials: Ten bituminous distributors and ten chip spreading operations were investigated the former by cotton pad, cup, and trough tests; the latter by measuring the distance covered by a truckload and by placing pan...

Nuclear magnetic resonance studies of ancient buried wood-II. Observations on the origin of coal from lignite to bituminous coal

Science.gov (United States)

Hatcher, P.G.; Breger, I.A.; Szeverenyi, N.; Maciel, G.E.

1982-01-01

Coalified logs ranging in age from Late Pennsylvania to Miocene and in rank from lignite B to bituminous coal were analyzed by 13C nuclear magnetic resonance (NMR) utilizing the cross-polarization, magic-angle spinning technique, as well as by infrared spectroscopy. The results of this study indicate that at least three major stages of coalification can be observed as wood gradually undergoes transformation to bituminous coal. The first stage involves hydrolysis and loss of cellulose from wood with retention and differential concentration of the resistant lignin. The second stage involves conversion of the lignin residues directly to coalified wood of lignitic rank, during which the oxygen content of intermediate diagenetic products remains constant as the hydrogen content and the carbon content increases. These changes are thought to involve loss of methoxyl groups, water, and C3 side chains from the lignin. In the third major stage of coalification, the coalified wood increases in rank to subbituminous and bituminous coal; during this stage the oxygen content decreases, hydrogen remains constant, and the carbon content increases. These changes are thought to result from loss of soluble humic acids that are rich in oxygen and that are mobilized during compaction and dewatering. Relatively resistant resinous substances are differentially concentrated in the coal during this stage. The hypothesis that humic acids are formed as mobile by-products of the coalification of lignin and function only as vehicles for removal of oxygen represents a dramatic departure from commonly accepted views that they are relatively low-molecular-weight intermediates formed during the degradation of lignin that then condense to form high-molecular-weight coal structures. ?? 1982.

An International Peer Review of the Safety Options Dossier of the Project for Disposal of Radioactive Waste in Deep Geological Formations (Cigéo). Final Report of the IAEA International Review Team November 2016

International Nuclear Information System (INIS)

2017-07-01

The French Nuclear Safety Authority (Autorité de sûreté nucléaire, ASN) is preparing the evaluation of a licence application for the creation of a deep geological disposal facility in 2018, called Cigéo, for intermediate level, high level and long lived radioactive waste. This licence is preceded by the submission of a Safety Options Dossier to ASN, which provides the French National Radioactive Waste Management Agency (Agence nationale pour la gestion des déchets radioactifs, Andra) the possibility to receive advice from ASN on the preparation of the licence application on the safety principles and approach. The Safety Options Dossier sets out the chosen objectives, concepts and principles for ensuring the safety of the facility. ASN requested the IAEA to organize an international peer review of the Safety Options Dossier. This publication presents the consensus view of the international group of experts convened by the IAEA to conduct the review against the relevant IAEA safety standards and proven international practice and experience. The experts acted in a personal capacity and the views expressed do not necessarily reflect those of the IAEA, the governments of the nominating Member States or the nominating organizations. The basis of this peer review is the set of documents provided by Andra, as the agency responsible for the development of the Cigéo project and for its safety. Consequently, the findings of the reviews are addressed directly to Andra. This publication, however, is primarily submitted to ASN to review the outcomes of the Andra project.

Nagra technical report 14-02, geological basics - Dossier II - Sediments and tectonic considerations; SGT Etappe 2: Vorschlag weiter zu untersuchender geologischer Standortgebiete mit zugehörigen Standortarealen für die Oberflächenanlage -- Geologische Grundlagen -- Dossier II -- Sedimentologische und tektonische Verhältnisse

Energy Technology Data Exchange (ETDEWEB)

Madritsch, H.; Deplazes, G.

2014-12-15

This dossier is the second of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It considers the sediments that can be used and discusses tectonic considerations. As an introduction, the geological framework is discussed with the various sediments from the Paleozoic, Mesozoic and Cenozoic periods. The various methods used to investigate the rock, such as drilling and reflection-seismic methods along with the investigation of surface formations are discussed. A detailed discussion of the stratigraphic and sedimentological characteristics of the various formations follows. Geological structures and the tectonics in the proposed areas are discussed, as are the depth and thickness of the structures.

Co-combustion characteristics and blending optimization of tobacco stem and high-sulfur bituminous coal based on thermogravimetric and mass spectrometry analyses.

Science.gov (United States)

Zhang, Kaihua; Zhang, Kai; Cao, Yan; Pan, Wei-ping

2013-03-01

Despite much research on co-combustion of tobacco stem and high-sulfur coal, their blending optimization has not been effectively found. This study investigated the combustion profiles of tobacco stem, high-sulfur bituminous coal and their blends by thermogravimetric analysis. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions were also studied by thermogravimetric and mass spectrometry analyses. The results indicated that combustion of tobacco stem was more complicated than that of high-sulfur bituminous coal, mainly shown as fixed carbon in it was divided into two portions with one early burning and the other delay burning. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions of the blends present variable trends with the increase of tobacco stem content. Taking into account the above three factors, a blending ratio of 0–20% tobacco stem content is conservatively proposed as optimum amount for blending. Copyright © 2012 Elsevier Ltd. All rights reserved.

Adhesion Promoters in Bituminous Road Materials: A Review

Directory of Open Access Journals (Sweden)

Cesare Oliviero Rossi

2017-05-01

Full Text Available This review focuses on certain classes of organic compounds known variously in the specific literature of asphalt as adhesion promoters, antistripping agents, wetting agents, antistrips, or adhesion agents. These kinds of organic additives are currently formulated to enhance the bitumen coating of mineral aggregates and improve the workability of asphalt mixtures. In this review, the term “adhesion promoters” includes both synthetic organic compounds as well as those extracted from natural resources, mixed in trace amounts to bitumen. Their main role is to alter the interfacial energy, so that the presence of water, even in trace, does not weaken the bitumen-aggregate bond and tends to favor adhesion. The report also considers the chemical functionalities that play a predominant role in bonding, as well as the effects of surface modification of the aggregate due to the presence of adhesion promoters in pre-blended bituminous mixtures. Although bitumen is widely used in road pavement construction and the discussion is mainly addressed to the improvement of adhesion in road materials, adhesion and wetting properties can also represent a general issue in various bitumen-based industrial products.

Introduction to Dossier. International Migrations in Latin America: Critical Views on the Production of a Field of Knowledge

Directory of Open Access Journals (Sweden)

Gioconda Herrera

2017-05-01

Full Text Available This article presents a reflection from three dimensions on epistemological and political logics that crosscut the studies on migrations in Latin America: 1 the increasing heterogeneity of flows and the need to rethink the conceptual categories from which migrations are addressed; 2 the dialogue and appropriation of analytical frameworks produced in other regions in Latin American studies; and 3 the political agendas of the States in the region and in the North, and their selective influence on the production of knowledge. The objective is to offer a general reflection on the production of the field of studies on migrations in Latin America to serve as a context for the analysis of the five articles presented in this dossier of Íconos. Revista de Ciencias Sociales.

Geochemistry of radioactive elements in bituminous sands and sandstones of Permian bitumen deposits of Tatarstan (east of the Russian plate)

Science.gov (United States)

Mullakaev, A. I.; Khasanov, R. R.; Badrutdinov, O. R.; Kamaletdinov, I. R.

2018-05-01

The article investigates geochemical features of Permian (Cisuralian, Ufimian Stage and Biarmian, Kazanian Stage of the General Stratigraphic Scale of Russia) bituminous sands and sandstones located on the territory of the Volga-Ural oil and gas province (Republic of Tatarstan). Natural bitumens are extracted using thermal methods as deposits of high-viscosity oils. In the samples studied, the specific activity of natural radionuclides from the 238U (226Ra), 232Th, and 40K series was measured using gamma spectrometry. As a result of the precipitation of uranium and thorium and their subsequent decay, the accumulation of radium (226Ra and 228Ra) has been shown to occur in the bituminous substance. In the process of exploitation of bitumen-bearing rock deposits (as an oil fields) radium in the composition of a water-oil mixture can be extracted to the surface or deposited on sulfate barriers, while being concentrated on the walls of pipes and other equipment. This process requires increased attention to monitoring and inspection the environmental safety of the exploitation procedure.

The Einstein dossiers science and politics - Einstein's Berlin period with an appendix on Einstein's FBI file

CERN Document Server

Grundmann, Siegfried

2004-01-01

In 1919 the Prussian Ministry of Science, Arts and Culture opened a dossier on "Einstein's Theory of Relativity." It was rediscovered by the author in 1961 and is used in conjunction with numerous other subsequently identified 'Einstein' files as the basis of this fascinating book. In particular, the author carefully scrutinizes Einstein's FBI file from 1950-55 against mostly unpublished material from European including Soviet sources and presents hitherto unknown documentation on Einstein's alleged contacts with the German Communist Party and the Comintern. Siegfried Grundmann's thorough study of Einstein's participation on a committee of the League of Nations, based on archival research in Geneva, is also new. This book outlines Einstein's image in politics and German science policy. It covers the period from his appointment as a researcher in Berlin to his fight abroad against the "boycott of German science" after World War I and his struggle at home against attacks on "Jewish physics" of which he was made...

Application of infrared camera to bituminous concrete pavements: measuring vehicle

Science.gov (United States)

Janků, Michal; Stryk, Josef

2017-09-01

Infrared thermography (IR) has been used for decades in certain fields. However, the technological level of advancement of measuring devices has not been sufficient for some applications. Over the recent years, good quality thermal cameras with high resolution and very high thermal sensitivity have started to appear on the market. The development in the field of measuring technologies allowed the use of infrared thermography in new fields and for larger number of users. This article describes the research in progress in Transport Research Centre with a focus on the use of infrared thermography for diagnostics of bituminous road pavements. A measuring vehicle, equipped with a thermal camera, digital camera and GPS sensor, was designed for the diagnostics of pavements. New, highly sensitive, thermal cameras allow to measure very small temperature differences from the moving vehicle. This study shows the potential of a high-speed inspection without lane closures while using IR thermography.

Nagra technical report 14-02, Geological basics - Dossier VI - Barrier properties of proposed host rock sediments and neighbouring rock; SGT Etappe 2: Vorschlag weiter zu untersuchender geologischer Standortgebiete mit zugehörigen Standortarealen für die Oberflächenanlage -- Geologische Grundlagen -- Dossier VI -- Barriereneigenschaften der Wirt- und Rahmengesteine

Energy Technology Data Exchange (ETDEWEB)

Gautschi, A.; Deplazes, G.; Traber, D.; Marschall, P. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Mazurek, M.; Gimmi, T.; Maeder, U. [Institute of Geological Sciences, University of Berne, Berne (Switzerland)

2014-12-15

This dossier is the sixth of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It discusses the barrier properties of the proposed host rock sediments and neighbouring rock layers. The mineralogical composition of the host rocks are discussed as are their pore densities and hydrological properties. Diffusion aspects are discussed. The aquifer systems in the proposed depository areas and their classification are looked at. The barrier properties of the host rocks and those of neighbouring sediments are discussed. Finally, modelling concepts and parameters for the transport of radionuclides in the rocks are discussed.

The projects of reducing environmental pollution at the collieries belonging to Petrosani Autonomous Bituminous Coal Administration

International Nuclear Information System (INIS)

Arad, V.; Arad, S.; Costinas, B.; Marchis, G.

1997-01-01

The economic development in the Jiu Valley, as practised in the mining and processing of bituminous coal, has had a dynamic character without taking into account, however, the harmful impact on the environment. The most severe problem of environmental pollution in the Jiu Valley is that of the pollution of the Jiu River due to the discharge of waste water from the technological processes of mining and processing coal. This paper presents some solutions for reducing this environmental pollution, especially the Jiu water pollution. 1 ref

Adsorption of SO2 on bituminous coal char and activated carbon fiber prepared from phenol formaldehyde

Science.gov (United States)

DeBarr, Joseph A.; Lizzio, Anthony A.; Daley, Michael A.

1996-01-01

Carbon-based materials are used commercially to remove SO2 from coal combustion flue gases. Historically, these materials have consisted of granular activated carbons prepared from lignite or bituminous coal. Recent studies have reported that activated carbon fibers (ACFs) may have potential in this application due to their relatively high SO2 adsorption capacity. In this paper, a comparison of SO2 adsorption for both coal-based carbons and ACFs is presented, as well as ideas on carbon properties that may influence SO2 adsorption

Chemical composition of spoil from bituminous coal and anthracite in Spain. Composicion quimica de los esteriles de hulla y antracita de Espana

Energy Technology Data Exchange (ETDEWEB)

Gonzalez Canibano, J; Fernandez Valcarce, A

1991-05-01

The article describes the chemical composition of spoil from bituminous coal and anthracite in Spain. Chemical composition, mineralogical properties and physical and mechanical characteristics are used to determine the most suitable application for the spoil in order to solve the problem of disposal. 20 refs., 5 figs., 4 tabs.

Report on the bituminous coal liquefaction sub-committee in fiscal 1993; 1993 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This paper reports the activities of the bituminous coal liquefaction sub-committee in fiscal 1993. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant, launched in fiscal 1991, will be performed under the operation research plan for efficient operation, based on the result of discussing the total project cost in fiscal 1992. The status of constructing the 150-t/d pilot plant in fiscal 1993 is in the phase of making the foundations subsequently from fiscal 1992, procurement of devices and construction materials, constructions of iron structures, installation, heat insulation, and painting, and building the central control building and piping facilities outside the battery limit. The paper also reports the tests and investigations on improving performance of natural pylite catalyst, the tests and investigations on improving performance of circulating solvent, and the technological investigations on structuring a liquefying reaction data analyzing system. For the supportive researches on the pilot plant, the paper describes studies by using a 1-t/d PSU, studies on coal liquefaction conditions, studies on synthesized iron sulfide catalysts, and studies on solvent hydrogenating catalysts. A comprehensive discussion was also given. (NEDO)

Low-temperature carbonization of bituminous coal for the production of solid, liquid, and gaseous fuels

Energy Technology Data Exchange (ETDEWEB)

1942-01-01

Properties and uses of low-temperature coke for producing ferrosilicon, CaC/sub 2/ generator gas and water gas, as a fuel for boilers and household use and as a diluent for coking coal, and the properties and uses of low-temperature tar, gasoline, gas, and liquefied gas are described. By using a circulating gas, it is possible to obtain in low-temperature carbonization of bituminous coal a fuel oil for the navy. Aging-test data of such an oil are given. Several plants in Upper Silesia, using the Lurgi circulation process are producing a fuel oil that meets specification.

Determination of bitumen and rubber content in bituminous mixes containing crumb tyre rubber; Determinacion del contenido de betum y de caucho en las mezclas bituminosas que incorporan plvo de caucho procedente de neumaticos fuera de uso

Energy Technology Data Exchange (ETDEWEB)

Rubio Guzamn, B.; Jimenez Saez, R.

2009-07-01

In recent years the use of crumb rubber from scrap tyres as a component of hot bituminous mixes for road construction, has been officially promoted by the Public Administration in Spain, by issuing several publications of both informative and normative nature, aimed to spread knowledge and experiences on the subject and also to specify the requirement and regulate the working applications for this material. However, it also seems necessary to develop new test methods which, allows control of the rubber content in crumb rubber-added mixes, regardless of the process (wet or dry) followed for the mix production. This article describes a procedure reliable enough to determine both the soluble bituminous binder and the rubber contents in bituminous mixes based on two combined, previously standardized test methods: binder extraction with solvent and ignition. (Author) 7 refs.

Polygenic formation model of the planet's bituminous belts

Science.gov (United States)

Dmitrievsky, A. N.; Balanyuk, I. E.

2011-05-01

In recent years, much attention has been paid to nontraditional hydrocarbon sources. Today the portion of nontraditional gas in the world extraction is 15% or 450 billion cubic meters, which hat makes up the volume of total gas exports from Russia. As is known, the easy-prospecting oil has been already found. The innovative technologies in geophysics, drilling, and excavation and the increased extraction coefficient expect further development and industrial compliance with these requirements. Based on calculations, the world oil reserves are now one trillion of stock tank barrels and one trillion barrels have been already extracted. The evergrowing demand for energy gives rise to the necessity of searching for and extracting more oil resources, and both these aspects are unique problems. The search for profitable petroleum deposits has become more and more difficult even in the leading companies. The increment of the world resources is a key vital question; therefore, the elaboration of criteria for the discovery of nontraditional deposits take on special significance in the economic respect. The authors are working out a conception that will be a guideline for future finding of the richest oil deposits in active geodynamic zones. For the first time, we suggest the polygenic formation model of the planet's bituminous belts.

A process for the bituminization of radioactive wastes

International Nuclear Information System (INIS)

Bar-Ziv, E.; Manor, D.; Levin, I.

1977-06-01

A process is described for the incorporation of sodium nitrate solutions in bitumen, with a view to the bituminization of radioactive wastes. This process has involved the development of a chemical process and its technological application. A double jacket reactor equipped with an anchor-type stirrer has been built. Sodium nitrate (NaNO 3 ) solutions with sodium hydroxide (NaOH) are fed into the reactor simultaneously with a bitumen emulsion while heated oil is circulated through the double jacket. After all the water has evaporated, the mixture is ''simmered'' at 170/180 deg C for up to 5 hours in order to get a homogeneous product which will be suitable for final storage. The product contains small salt crystals (10/50 μm) and has high viscosity (200/2000 poise at 160 deg C and 12 rpm), so that the possibility of sedimentation is eliminated. In comparative experiments with molten bitumen, large salt aggregates, inhomogeneously distributed, make the product unsuitable. It has been found that NaOH is responsible for the polimerization of the bitumen, which raises its viscosity. The degree of polimerization depends on the NaOH concentration and ''simmering'' time and temperature. NaOH is added to NaNO 3 in order to raise the mixture's viscosity and thereby prevent sedimentation

PNGMDR 2013-2015. 2015 report by the 'optimisation of the distribution of wastes among management sectors' work-group

International Nuclear Information System (INIS)

2015-01-01

PNGMDR is the French national plan for the management of radioactive materials and wastes. After a discussion of the stakes associated with the optimisation of the different sectors involved in radioactive waste management (production, sorting, processing, packaging, warehousing, storage), this reports proposes a description of wastes for which a sector optimisation study has been performed (graphite wastes, Marcoule bitumen packages, common solid residues, cemented solid wastes in concrete containers from Areva La Hague), describes the various studies optimisation ways and alternate scenarios for these different wastes. It analyses and discusses the progress status of the studies optimisation ways: improvement of the characterisation of graphite and bituminous wastes, studies and works on the storage of low-level-long-lived wastes, studies on the processing of graphite wastes, of bituminous packages and common solid residues. Other issues are evoked: the case of wastes produced by dismantling operations, and a technical-economic approach. Perspectives and future works are discussed for the different considered wastes

Safety Analysis Report - Packages, 9965, 9968, 9972-9975 Packages

International Nuclear Information System (INIS)

Blanton, P.

2000-01-01

This Safety Analysis Report for Packaging (SARP) documents the analysis and testing performed on four type B Packages: the 9972, 9973, 9974, and 9975 packages. Because all four packages have similar designs with very similar performance characteristics, all of them are presented in a single SARP. The performance evaluation presented in this SARP documents the compliance of the 9975 package with the regulatory safety requirements. Evaluations of the 9972, 9973, and 9974 packages support that of the 9975. To avoid confusion arising from the inclusion of four packages in a single document, the text segregates the data for each package in such a way that the reader interested in only one package can progress from Chapter 1 through Chapter 9. The directory at the beginning of each chapter identifies each section that should be read for a given package. Sections marked ''all'' are generic to all packages

Fire and explosion incident at bituminization demonstration facility of PNC Tokai works, on march 11, 1997

International Nuclear Information System (INIS)

Miura, A.; Sato, Y.; Koyama, T.; Omori, E.; Kato, Y.; Suzuki, H.; Norjiri, I.; Yamanouchi, T.

2001-01-01

On March 11, a fire and explosion incident occurred at the Bituminization Demonstration Facility (BDF) of Tokai Reprocessing Plant in Power Reactor and Nuclear Fuel Development Corporation (PNC). Soon after the incident, PNC (now reorganized to JNC) started to investigate the facility damage, operational records around the incident, technical notes including facility design and reviews of R and D results, operators witness and to perform several analysis, tests and calculations. This paper describes outline and cause of the incident which were concluded based on the results of continuous serious investigation, analysis and calculation. (author)

Bituminous solidification, disposal, transport and burial of spent ion-exchange resins. Part of a coordinated programme on treatment of spent ion exchange resins

International Nuclear Information System (INIS)

Mozes, G.; Kristof, M.

1983-07-01

The project dealing with the incorporation of spent ion-exchange resins into bitumen was performed within the Agency coordinated research programme on treatment of spent ion-exchange resins. Physical and chemical properties of commercial ion-exchange resins, bitumens and bituminized resins were studied. It was shown that bitumen with low oil content and with a softening point of 60-70 deg. C are applicable for the incorporation of resins. The final waste form is allowed to contain maximum 50% resin. The comprehensive study of the biological resistance of B-30 bitumen was performed. That showed that any bacteriological attack can be regarded as generally insignificant. A continuously operating technology was realized on a semi-plant scale. The best operating conditions of this technology were determined. On the basis of the experience gained from the experiments a design of the bituminization plant of 50m 3 dry resin/year treatment capacity was proposed

Effect of transesterification degree and post-treatment on the in-service performance of NCO-functionalized vegetable oil bituminous products

OpenAIRE

Cuadri Vega, Antonio Abad; García Morales, Moisés; Navarro Domínguez, Francisco Javier; Partal López, Pedro

2014-01-01

The bitumen modification through polyurethane prepolymers presents significant benefits for the manufacture of bituminous products for the paving industry. In this sense, this work explores the use, as bitumen modifier, of a novel reactive prepolymer synthesized by reaction of 4,4´,diphenylmethane diisocyanate (MDI) and a vegetable oil-based polyol, castor oil (CO), previously transesterified with pentaerythritol. On the one hand, thermal analysis on transesterified CO revealed a highly stabl...

Dependence of carbon dioxide sorption on the petrographic composition of bituminous coals from the Czech part of the Upper Silesian Basin, Czech Republic

Energy Technology Data Exchange (ETDEWEB)

Zuzana Weishauptova; Ivana Sykorova [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Institute of Rock Structure and Mechanics

2011-01-15

The effect of the rank and of the maceral composition of bituminous coal on carbon dioxide sorption capacity was studied on the basis of samples from two coal mines (Darkov, CSM) from the Czech part of the Upper Silesian Basin. The samples from the two mines cover a small but very significant section of coalification within the transition zone between high-volatile bituminous A coal and medium-volatile bituminous coal, where porosity and sorption properties pass through their minima. The coal porous system was characterized by the micropore volume evaluated using the sorption isotherm of carbon dioxide and the volumes of meso-, macro- and coarse pores were determined by high-pressure mercury porosimetry. The micropore fraction in the coal porous system ranged between 53% and 75%. It was particularly high in coals with high vitrinite content, namely collotelinite, and also in coals with high inertinite content. The carbon dioxide sorption capacity was determined from the carbon dioxide sorption isotherms measured using a gravimetric sorption analyzer at 298 K until a relative pressure of 0.015 p/p{sub s}, and was interpreted by characteristic parameters of the Dubinin and Langmuir equations. It was found that the adsorbed amount of CO{sub 2} in the CSM coal increases with the content of vitrinite and collotelinite, whereas no increase or only a slight increase was observed for the Darkov coal. The tendency of adsorption capacity to depend on maceral composition, and also to some extent on coalification, observed for the CSM coal, may be related to higher microporosity due to the coalification process or oxidative processes leading to the formation of pseudovitrinite. 42 refs., 8 figs., 4 tabs.

Petrography and geochemistry of Oligocene bituminous coal from the Jiu Valley, Petrosani basin (southern Carpathian Mountains), Romania

Energy Technology Data Exchange (ETDEWEB)

Belkin, Harvey E.; Tewalt, Susan J. [U.S. Geological Survey, 956 National Center, Reston, VA 20192 (United States); Hower, James C. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); Stucker, J.D. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); University of Kentucky Department of Earth and Environmental Sciences, Lexington, KY 40506 (United States); O' Keefe, Jennifer M.K. [Morehead State University, Morehead, KY, 40351 (United States); Tatu, Calin A. [University of Medicine and Pharmacy, Department of Immunology, Clinical Laboratory No. 1, Pta. E. Murgu No. 2, RO-1900 Timisoara (Romania); Buia, Grigore [University of Petrosani, Department of Geology, University St. 20, RO-2675 Petrosani (Romania)

2010-05-01

Belt samples of Oligocene (Chattian) bituminous coal from 10 underground mines located in the Jiu Valley, Hunedoara County, Petrosani basin, Romania, have been examined and analyzed for proximate and ultimate analysis, major-, minor- and trace-element chemistry, organic petrography, and vitrinite reflectance. The mineral chemistry and mode of occurrence of trace elements also have been investigated using SEM and electron microprobe techniques. Twenty coal beds occur in the Jiu Valley and most of the samples are from bed no. 3, the most productive bed of the Dilja-Uricani Formation of Oligocene age. The Petrosani basin, oriented SW-NE, is 48-km long, 10-km wide at the eastern part and 2-km wide at the western part. The coal mines are distributed along the center of the valley generally following the Jiu de Vest River. Reflectance measurements indicate that the rank of the coals ranges from high-volatile B to high-volatile A bituminous. Overall, rank decreases from the southwest to the northeast. In bed no. 3, R{sub max} varies from 0.75% in the northeast to 0.93% in the southwest. Although, most Oligocene coals in Romania and adjacent countries are lignite in rank, the Jiu Valley bituminous coals have been affected by regional metamorphism and attending hydrothermal fluids related to the Alpine orogenic event. The coals are all dominated by vitrinite; resinite and funginite are important minor macerals in most of the coals. Pyrite and carbonate generally dominate the mineral assemblages with carbonate more abundant in the northwest. Siderite occurs as nodules and masses within the macerals (generally vitrinite). Dolomite and calcite occur as fracture fillings, plant-cell fillings, and in other authigenic forms. Late-stage fracture fillings are siderite, dolomite, calcite, and ankerite. In one instance, two populations of siderite ({proportional_to} 35 and {proportional_to} 45 wt.% FeO) plus ankerite fill a large fracture. Late-stage pyrite framboid alteration is Ni

Report on the bituminous coal liquefaction sub-committee in fiscal 1992; 1992 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the bituminous coal liquefaction sub-committee in the Sunshine Project in fiscal 1992. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant was launched in fiscal 1991. It is necessary to execute the pilot plant plan steadily in the future, and at the same time, reliably acquire different data by means of supportive researches. Economic performance of the process is also important. The first sub-committee meeting presented the following agenda: the status of constructing the 150-t/d pilot plant, tests and investigations thereon, research works by using a 1-t/d PSU, development of the most suitable coal refining technology, development of a coal pretreatment technology, improvement of the distilled oil distribution, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. The second sub-committee meeting presented the following agenda: the status of constructing the pilot plant, tests and investigations on improving the performance of natural pylite catalyst and circulating solvent, technological investigations on structuring a liquefying reaction data analyzing system, studies using a 1-t/d PSU, development of the most suitable coal refining technology, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. (NEDO)

Packaging Solutions : Delivering customer value through Logistical Packaging: A Case Study at Stora Enso Packaging

OpenAIRE

Shan, Kun; Julius, Joezer

2015-01-01

AbstractBackground;Despite of the significant role of packaging within logistics and supply chain management, packaging is infrequently studied as focal point in supply chain. Most of the previous logistics research studies tend to explain the integration between packaging and logistics through logistical packaging. In very rare cases, the studies mentioned about customer value. Therefore the major disadvantage of these studies is that, they didn’t consider logistical packaging and customer v...

Shaft-retort for treating waste materials, like washery waste, bituminous shale, oil-bearing sands and the like

Energy Technology Data Exchange (ETDEWEB)

Koppers, H

1916-10-29

A shaft-retort for converting waste materials, like washery waste, bituminous shale, oil-bearing sands, brown coal and non-coking mineral coal to oil and tar by supplying heat through the shaft wall formed of an iron-sheet to the material, which is forced through a feeding member perforated for the removal of gases and vapors, and moved downward in a thin layer on the shaft wall; that is characterized by the fact that the iron heating sheet is made rotatable for the purpose of equalizing overheating of itself and the material to be treated.

The hydrogasification of lignite and sub-bituminous coals

Science.gov (United States)

Bhatt, B.; Fallon, P. T.; Steinberg, M.

1981-02-01

A North Dakota lignite and a New Mexico sub-bituminous coal have been hydrogenated at up to 900°C and 2500 psi hydrogen pressure. Yields of gaseous hydrocarbons and aromatic liquids have been studied as a function of temperature, pressure, residence time, feed rates and H2/coal ratio. Coal feed rates in excess of 10 lb/hr have been achieved in the 1 in. I. D.×8 ft reactor and methane concentration as high as 55% have been observed. A four-step reaction model was developed for the production and decomposition of the hydrocarbon products. A single object function formulated from the weighted errors for the four dependent process, variables, CH4, C2H6, BTX, and oil yields, was minimized using a program containing three independent iterative techniques. The results of the nonlinear regression analysis for lignite show that a first-order chemical reaction model with respect to C conversion satisfactorily describes the dilute phase hydrogenation. The activation energy for the initial products formation was estimated to be 42,700 cal/gmole and the power of hydrogen partial pressure was found to be +0.14. The overall correlation coefficient was 0.83. The mechanism, the rate expressions, and the design curves developed can be used for scale-up and reactor design.

Packaging fluency

DEFF Research Database (Denmark)

Mocanu, Ana; Chrysochou, Polymeros; Bogomolova, Svetlana

2011-01-01

Research on packaging stresses the need for packaging design to read easily, presuming fast and accurate processing of product-related information. In this paper we define this property of packaging as “packaging fluency”. Based on the existing marketing and cognitive psychology literature on pac...

Method of and arrangement for extracting volatile bituminous condensable materials from shales, etc

Energy Technology Data Exchange (ETDEWEB)

Flodin, H G

1918-06-22

A method and arrangement for extracting volatile bituminous condensable materials, such as oils and similar material, as well as sulfur, whereby the material used is heated in a generator by introduction of a hot indifferent gas, such as carbon monoxide or generator gas, which is brought into circulation through a heating apparatus and the generator are characterized by removal of the shales distilled in the generator and their being charged into another generator or furnace where they are oxidized by means of air. Sulfur dioxide and carbon dioxide and possible carbon monoxide are formed and the sulfur dioxide and carbon dioxide formed by the oxidation of the distilled shales are brought into contact with hot coal for regeneration of sulfur and carbon monoxide. The patent contains five additional claims.

Microelectronic packaging

CERN Document Server

Datta, M; Schultze, J Walter

2004-01-01

Microelectronic Packaging analyzes the massive impact of electrochemical technologies on various levels of microelectronic packaging. Traditionally, interconnections within a chip were considered outside the realm of packaging technologies, but this book emphasizes the importance of chip wiring as a key aspect of microelectronic packaging, and focuses on electrochemical processing as an enabler of advanced chip metallization.Divided into five parts, the book begins by outlining the basics of electrochemical processing, defining the microelectronic packaging hierarchy, and emphasizing the impac

Eocene bituminous coal deposits of the Claiborne group, Webb County, Texas

Science.gov (United States)

Hook, Robert W.; Warwick, Peter D.; Warwick, Peter D.; Karlsen, Alexander K.; Merrill, Matthew D.; Valentine, Brett J.

2011-01-01

Two bituminous coal zones, the San Pedro and the Santo Tomas, in the middle Eocene Claiborne Group of Webb County, south Texas (Figure 1), are among the coal resources that are not evaluated quantitatively as part of the current Gulf Coastal Plain coal resource assessment. Coal beds within these zones were mined by underground methods northwest of Laredo until 1939 and have been intermittently mined at the surface since 1979. These coals have long been regarded as unique within the Gulf Coast Tertiary coal-bearing section because they are high-volatile C bituminous in rank and because their physical characteristics resemble upper Carboniferous cannel coals of the Appalachians and Europe.Discontinuous exposures of the Santo Tomas and the underlying San Pedro coal zone extend northwestward from Dolores for approximately 15 to 21 mi along the breaks of the Rio Grande and its tributaries in Webb County (Figure 1). This part of south Texas lies along the southwestern flank of the Rio Grande Embayment, which extends south and southeastwardly through the Mexican States of Coahuila, Nuevo León, and Tamaulipas (Figure 1). Within the embayment, the lower to middle part of the Claiborne Group consists of marine mudstones (Reklaw Formation) in the east and northeast and sandstones and mudstones (Bigford Formation) in the south and southwest (Figure 2). The marine mudstones coarsen upward into fluvial-deltaic sandstones (Queen City Sand) that prograded gulfward across eastern and central Texas (Guevara and Garcia, 1972). To the west and southwest, the interval overlying the Bigford Formation becomes less sandy, and claystones (El Pico Clay) predominate. Although the San Pedro coal zone has been placed traditionally near the top of the Bigford Formation and the Santo Tomas coal zone near the base of the El Pico Clay, recent work has failed to validate a mappable contact between these formations (Warwick and Hook, 1995). The coal beds dip northeast at less than 2 degrees towards

An evidence for the strong association of N-methyl-2-pyrrolidinone with some organic species in three Chinese bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Liu, C.M.; Zong, Z.M.; Jia, J.X.; Liu, G.F.; Wei, X.Y. [China University of Mining and Technology, Xuzhou (China). School for Chemical Engineering

2008-04-15

Three Chinese bituminous coals collected from Shenfu, Heidaigou and Feicheng coal fields were respectively extracted with carbon-disulfide/N-methyl-2-pyrrolidinone (CS{sub 2}/NMP) mixed solvent (volume ratio 1:1) at room temperature followed by distillation of CS{sub 2} under ambient pressure and subsequent removal of most of NMP by distillation at 110{sup o}C under reduced pressure to afford mixed solvent-extractable fractions (MSEFs) with small amount of NMP. Acetone-extractable fraction 1 (AEF1) was obtained by extracting each MSEF under ultrasonic irradiation at room temperature and subsequently using a Soxhlet extractor. Direct extraction of each bituminous coal affords acetone-soluble fraction 2 (AEF2). GC/MS analysis shows that mlz of base or secondary peak in mass spectra of a series of components from each AEF1 is 98, whereas such components were not detected in AEF2. Since m/z of base peak in mass spectrum of NMP itself is 99, the base or secondary peak at m/z 98 should result from loss of a-H from NMP, i.e., NMP is strongly associated with some organic species (OSs) and thereby the components detected with base or secodary peak at m/z 98 in their mass spectra should be associated NMP-OS.

The Packaging Handbook -- A guide to package design

International Nuclear Information System (INIS)

Shappert, L.B.

1995-01-01

The Packaging Handbook is a compilation of 14 technical chapters and five appendices that address the life cycle of a packaging which is intended to transport radioactive material by any transport mode in normal commerce. Although many topics are discussed in depth, this document focuses on the design aspects of a packaging. The Handbook, which is being prepared under the direction of the US Department of Energy, is intended to provide a wealth of technical guidance that will give designers a better understanding of the regulatory approval process, preferences of regulators in specific aspects of packaging design, and the types of analyses that should be seriously considered when developing the packaging design. Even though the Handbook is concerned with all packagings, most of the emphasis is placed on large packagings that are capable of transporting large radioactive sources that are also fissile (e.g., spent fuel). These are the types of packagings that must address the widest range of technical topics in order to meet domestic and international regulations. Most of the chapters in the Handbook have been drafted and submitted to the Oak Ridge National Laboratory for editing; the majority of these have been edited. This report summarizes the contents

Thermo-mechanical behavior of bituminous mixtures at low temperatures. Links between the binder characteristics and the mix properties; Comportement thermomecanique des enrobes bitumeux a basses temperatures: relations entre les proprietes du liant et de l'enrobe

Energy Technology Data Exchange (ETDEWEB)

Olard, F.

2003-10-01

This thesis has been realized within the framework of a partnership between the Ecole Nationale des TPE, APPIA and EUROVIA. The company Total has also been associated to this project. The study deals with the thermo-mechanical behavior of bituminous materials at low temperatures. The aim is to establish the links between the characteristics of the binder and the properties of bituminous mixes at low temperatures, and to better understand the existing low-temperature parameters and criteria for binders (or to propose new ones), related to the in-situ behavior of bituminous mixtures. A large experimental campaign has been carried out so as to fulfill this goal. After a bibliographical study on the rheology and the thermo-mechanical properties of (pure or modified) binders, putties and mixes, the experimental campaign carried out both in the small strain domain and in the large strain domain, is presented. The low temperature behavior of binders has been evaluated with three common fundamental tests: i)the complex modulus determination, ii)the Bending Beam Rheometer and iii)the tensile strength at a constant strain rate and constant temperatures. A new three point bending test on pre-notched bitumen beams has also been developed at the ENTPE. The low-temperature fracture properties of bitumens were studied at constant temperatures and cross-head speeds considering the Linear Elastic Fracture Mechanics (LEFM) assumptions. The thermo-mechanical behavior of bituminous mixtures has been studied by performing i)complex modulus tests, ii)measurements of the coefficient of thermal dilatation and contraction, iii)tensile tests at constant temperatures and strain rates, and iv)Thermal Stress Restrained Specimen Tests. Apart from the determination of some pertinent links between binder and mix properties and discriminating characteristics with regard to the thermal cracking of bituminous mixes at low temperatures, the analysis has also consisted in modeling the behavior of

Inoculum density of Glomus mosseae and growth of onion plants in unsterilized bituminous coal spoil

Energy Technology Data Exchange (ETDEWEB)

Khan, A.G.

1988-01-01

The effect of inoculum, density (number of vesicular-arbuscular mycorrhizal (VAM) propagules g/sup -1/ of inoculum) on the growth of onions (Allium cepa L.) infected by Glomus mosseae (Nicol and Gerd). Gerdemann and Trappe, Comb nov in unsterilized coal spoil containing indigenous VAM fungi, including G. mosseae, was investigated. The amount of onion roots converted to mycorrhizas by inoculant fungus, estimated by a gridline intersect method, increased with inoculum density (..gamma..0.62, P0.05) until a plateau was reached. Onion growth responses also increased significantly (P<0.05) with the amount of VAM inoculum present in the coal spoil. The initial linear relationship between inoculum propagules (MPN estimates), percent colonization of onion roots and onion shoot dry weight became quadratic as the number of infection propagules increased. VAM infection had no significant effect on root:shoot ratios. Similarly there was no significant interaction (P>0.05) between the inoculum density, VAM-colonized root mass and the onion root:shoot fresh weight ratios. The amount of the windswept bituminous coal spoil bound to VAM (presumably because of VAM external hyphae) also increased as inoculum density increased (..gamma..0.63, P<0.05). There was a stronger correlation (ga0.85, P<0.05) between the amount of spoil adhered per plant and the root fresh wt plant/sup -1/ indicating that root effects were primarily responsible for increasing spoil adherence. There were negative correlations (P<0.05) between root fresh wt plant/sup -1/ (..gamma..-0.68), inoculum density (..gamma..-0.589), percent root elngth infected (..gamma..-0.73) and the amount of spoil adhered g/sup -1/ root fresh wt. The possible exploitation of VAM in revegetation of bituminous coal spoil is discussed. 25 refs., 2 tabs.

Report: Potential environmental impact of exempt site materials - a case study of bituminous road planings and waste soils.

Science.gov (United States)

Bark, Marjorie; Bland, Michael; Grimes, Sue

2009-09-01

The use of waste materials for ecological benefit, agricultural improvement or as part of construction works are often exempt from waste management control in order to maximize the reuse of material that would otherwise be disposed of to landfill. It is important, however, to determine whether there is potential for such waste to cause environmental harm in the context of the basis for granting exemptions under the relevant framework objective to ensure that waste is recovered or disposed of without risk to water, air, soil, plants or animals. The potential for environmental harm was investigated by leaching studies on two wastes commonly found at exempt sites: bituminous road planings and waste soils. For bituminous road planings, the organic components of the waste were identified by their solubility in organic solvents but these components would have low environmental impact in terms of bioavailability. Leaching studies of the heavy metals copper, lead and zinc, into the environment, under specific conditions and particularly those modelling acid rain and landfill leachate conditions showed that, except for copper, the amounts leached fell within Waste Acceptance Criteria compliance limits for defining waste as inert waste. The fact that the amount of copper leached was greater than the Waste Acceptance Criteria level suggests that either additional testing of wastes regarded as exempt should be carried out to ensure that they are in analytical compliance or that legislation should allow for the potential benefits of reuse to supersede deviations from analytical compliance.

Low-temperature tar from bituminous coal and its further treatment

Energy Technology Data Exchange (ETDEWEB)

Hansen, C J

1950-01-01

High-temperature carbonization of bituminous coal yields only 3 to 4 percent tar, as compared with 8 to 10 percent or even more for low-temperature carbonization. The yield of phenols is 20 to 30 times as great from the low-temperature tar. Five conditions that must be met by a satisfactory low-temperature carbonization process are listed. The only method that satisfies all of these conditions is the Brennstoff-Technik (BT) process, in which iron retorts with movable walls are used. One disadvantage of most of the other processes is the high-pitch content of the tar. These tars are processed further to a neutral oil and a phenol-containing oil which are good diesel fuels with high-cetane numbers; the neutral oil can be fractionated to give oils of high-, medium-, and low-cetane number. Attempts to fractionate the tar oil by solvents have not proved commercially useful. However, the tar can be diluted with low-temperature light oil and phenols extracted with NaOH solution without distillation. Some difficulty is found, owing to the simultaneous extraction of viscous resins and other products that are readily removed from the phenols by distillation.

Gasification of high ash, high ash fusion temperature bituminous coals

Science.gov (United States)

Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

2015-11-13

This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

Kinetics and equilibrium modeling of uranium(VI) sorption by bituminous shale from aqueous solution

International Nuclear Information System (INIS)

Ortaboy, Sinem; Atun, Gülten

2014-01-01

Highlights: • Oil shales are sedimentary rocks containing a polymeric matter in a mineral matrix. • Sorption potential of bituminous shale (BS) for uranium recovery was investigated. • U(VI) sorption increased with decreasing pH and increasing temperature. • Kinetic data were analyzed based on single and two resistance diffusion models. • The results fit well to the McKay equation assuming film and intraparticle diffusion. - Abstract: Sorption of U(VI) onto a bituminous shale (BS) from a nuclear power plant project site in Black Sea region was investigated for potential risk assessment when it releases into the environment with contaminated ground and surface water. The sorption characteristics of the BS for U(VI) recovery were evaluated as a function of contact time, adsorbent dosage, initial concentration, pH and temperature. Kinetic results fit better with pseudo-second-order model rather than pseudo-first-order. The possibility of diffusion process was analyzed based on Weber–Morris intra-particle diffusion model. The McKay equation assuming film- and intraparticle diffusion better predicted the data than the Vermeulen approximation presuming surface diffusion. Equilibrium sorption data were modeled according to the Langmuir, Dubinin–Radushkevich (D–R) and Freundlich isotherm equations. Sorption capacity increased from 0.10 to 0.15 mmol g −1 in 298–318 K temperature range. FT-IR analysis and pH dependent sorption studies conducted in hydroxide and carbonate media revealed that U(VI) species were sorbed in uranyl and its hydroxo forms on the BS. Desorption studies showed that U(VI) leaching with Black Sea water was negligible from the loaded BS. The activation parameters (E a , ΔH ∗ and ΔG ∗ ) estimated from diffusion coefficients indicated the presence of an energy barrier in the sorption system. However, thermodynamic functions derived from sorption equilibrium constants showed that overall sorption process was spontaneous in nature

Short story student-writers: active roles in writing through the use of e-portfolio dossier

Directory of Open Access Journals (Sweden)

Liliana Cuesta

2011-06-01

Full Text Available En este artículo se describen los efectos causados por el uso del enfoque de género y proceso y del dossier del portafolio electrónico en el desarrollo de la habilidad para escribir historias cortas de un grupo de estudiantes de undécimo grado de un colegio público en Bogotá. Este estudio nació de la necesidad por despertar el interés de los estudiantes frente al desarrollo de sus habilidades de escritura y por encontrar estrategias instruccionales para guiarlos durante las etapas de este proceso. El análisis de datos revela una mejoría significativa en la producción escrita y evidencia la aparición de nuevos roles por parte de los estudiantes: de un estado pasivo se transformaron en creadores, constructores y evaluadores activos de su proceso de producción escrita de historias cortas. Estos roles les ayudaron a reflexionar sobre su aprendizaje y a mejorar su capacidad para tomar decisiones y desarrollar su pensamiento crítico. Los resultados también validaron el uso que tiene el portafolio electrónico como una herramienta útil en el aprendizaje y la evaluación.

MEMS packaging

CERN Document Server

Hsu , Tai-Ran

2004-01-01

MEMS Packaging discusses the prevalent practices and enabling techniques in assembly, packaging and testing of microelectromechanical systems (MEMS). The entire spectrum of assembly, packaging and testing of MEMS and microsystems, from essential enabling technologies to applications in key industries of life sciences, telecommunications and aerospace engineering is covered. Other topics included are bonding and sealing of microcomponents, process flow of MEMS and microsystems packaging, automated microassembly, and testing and design for testing.The Institution of Engineering and Technology is

Packaging design criteria for the Hanford Ecorok Packaging

International Nuclear Information System (INIS)

Mercado, M.S.

1996-01-01

The Hanford Ecorok Packaging (HEP) will be used to ship contaminated water purification filters from K Basins to the Central Waste Complex. This packaging design criteria documents the design of the HEP, its intended use, and the transportation safety criteria it is required to meet. This information will serve as a basis for the safety analysis report for packaging

Development of advanced air-blown entrained-flow two-stage bituminous coal IGCC gasifier

Directory of Open Access Journals (Sweden)

Abaimov Nikolay A.

2017-01-01

Full Text Available Integrated gasification combined cycle (IGCC technology has two main advantages: high efficiency, and low levels of harmful emissions. Key element of IGCC is gasifier, which converts solid fuel into a combustible synthesis gas. One of the most promising gasifiers is air-blown entrained-flow two-stage bituminous coal gasifier developed by Mitsubishi Heavy Industries (MHI. The most obvious way to develop advanced gasifier is improvement of commercial-scale 1700 t/d MHI gasifier using the computational fluid dynamics (CFD method. Modernization of commercial-scale 1700 t/d MHI gasifier is made by changing the regime parameters in order to improve its cold gas efficiency (CGE and environmental performance, namely H2/CO ratio. The first change is supply of high temperature (900°C steam in gasifier second stage. And the second change is additional heating of blast air to 900°C.

Chemical and Pyrolytic Thermogravimetric Characterization of Nigerian Bituminous Coals

Directory of Open Access Journals (Sweden)

Nyakuma Bemgba Bevan

2016-12-01

Full Text Available The discovery of new coal deposits in Nigeria presents solutions for nation’s energy crises and prospects for socioeconomic growth and sustainable development. Furthermore, the quest for sustainable energy to limit global warming, climate change, and environmental degradation has necessitated the exploration of alternatives using cleaner technologies such as coal pyrolysis. However, a lack of comprehensive data on physico-chemical and thermal properties of Nigerian coals has greatly limited their utilization. Therefore, the physico-chemical properties, rank (classification, and thermal decomposition profiles of two Nigerian bituminous coals – Afuze (AFZ and Shankodi-Jangwa (SKJ – were examined in this study. The results indicate that the coals contain high proportions of C, H, N, S, O and a sufficiently high heating value (HHV for energy conversion. The coal classification revealed that the Afuze (AFZ coal possesses a higher rank, maturity, and coal properties compared to the Shankodi-Jangwa (SKJ coal. A thermal analysis demonstrated that coal pyrolysis in both cases occurred in three stages; drying (30-200 °C, devolatilization (200-600 °C, and char decomposition (600-1000 °C. The results also indicated that pyrolysis at 1000 °C is not sufficient for complete pyrolysis. In general, the thermochemical and pyrolytic fuel properties indicate that the coal from both places can potentially be utilized for future clean energy applications.

Packaging microservices

DEFF Research Database (Denmark)

Montesi, Fabrizio; Thrane, Dan Sebastian

2017-01-01

We describe a first proposal for a new packaging system for microservices based on the Jolie programming language, called the Jolie Package Manager (JPM). Its main features revolve around service interfaces, which make the functionalities that a service provides and depends on explicit. For the f......We describe a first proposal for a new packaging system for microservices based on the Jolie programming language, called the Jolie Package Manager (JPM). Its main features revolve around service interfaces, which make the functionalities that a service provides and depends on explicit...

Bituminization of simulated waste, spent resins, evaporator concentrates and animal ashes by extrusion process

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.

1986-01-01

The results of the study of simulated radwaste, spent ion-exchange resins, borates/evaporator-concentrates and animal ashes, in bituminized form, are presented and discussed. Distilled and oxidized bitumen were used for characterizing the crude material and simulated wastes-bitumen mixtures of varying weight composition 30, 40, 50, 60% by weight the dry waste material. The asphaltine and parafin contents in the bitumens were determined. Some additives and clays were used aiming best characteristics of solidified wastes. For leaching studies, granular ion-exchange resins were loaded with Cs 134 and mixtures of resins-bitumens were prepared. The leaching studies were executed using the IAEA recommendation and the ISO method. It was used a conventional screw-extruder, used in plastic industry, to determine operational conditions and process difficulties. Mixtures resins-bitumen and concentrate-bitumen in differents operational condition were prepared and analysed. (Author) [pt

PRIDE Surveillance Projects Data Packaging Project, Information Package Specification Version 1.0

Energy Technology Data Exchange (ETDEWEB)

Kelleher, D.M.; Shipp, R. L.; Mason, J. D.

2009-09-28

This document contains a specification for a standard XML document format called an information package that can be used to store information and the context required to understand and use that information in information management systems and other types of information archives. An information package consists of packaged information, a set of information metadata that describes the packaged information, and an XML signature that protects the packaged information. The information package described in this specification was designed to be used to store Department of Energy (DOE) and National Nuclear Security Administration (NNSA) information and includes the metadata required for that information: a unique package identifier, information marking that conforms to DOE and NNSA requirements, and access control metadata. Information package metadata can also include information search terms, package history, and notes. Packaged information can be text content, binary content, and the contents of files and other containers. A single information package can contain multiple types of information. All content not in a text form compatible with XML must be in a text encoding such as base64. Package information is protected by a digital XML signature that can be used to determine whether the information has changed since it was signed and to identify the source of the information. This specification has been tested but has not been used to create production information packages. The authors expect that gaps and unclear requirements in this specification will be identified as this specification is used to create information packages and as information stored in information packages is used. The authors expect to issue revised versions of this specification as needed to address these issues.

Burnout behaviour of bituminous coals in air-staged combustion conditions

Energy Technology Data Exchange (ETDEWEB)

Kluger, F.; Spliethoff, H.; Hein, K.R.G. [University of Stuttgart, Stuttgart (Germany). Inst. of Process Engineering and Power Plant (IVD)

2001-07-01

In order to determine the influence on burnout by the combustion conditions and the coal preparation, three bituminous coals sold on the world market, from three different locations in Poland, South Africa, and Australia, were studied more closely. For this purpose, the coals were ground in two different particle size ranges, which, besides the influence of the combustion conditions, such a temperature, residence time, and stoichiometry, made it possible to also investigate the impact on burnout by the coal preparation. The experiments were carried out in an electrically heated entrained-flow reactor with a thermal input of 8.5 kW. The parameters for the experiments are wall temperature (1000-1350{degree}C), air ratio (0.6-1.15) and two particle sizes (70% {lt} 75 {mu}m, 90% {lt} 75 {mu}m). The results show that in general, for increasing temperatures, the burnout quality will improve. For the Australian Illawara coal, another outcome is increased NOx emissions. Lowering the air ratio in the reduction zone leads to less NOx emission but to increased unburnt matter in ash. For the smaller particle size fraction, the analysis of the different particle sizes shows an improvement of the burnout without a change in NOx emissions. 10 refs., 10 figs., 2 tabs.

In-Package Chemistry Abstraction

Energy Technology Data Exchange (ETDEWEB)

P.S. Domski

2003-07-21

The work associated with the development of this model report was performed in accordance with the requirements established in ''Technical Work Plan for Waste Form Degradation Modeling, Testing, and Analyses in Support of SR and LA'' (BSC 2002a). The in-package chemistry model and in-package chemistry model abstraction are developed to predict the bulk chemistry inside of a failed waste package and to provide simplified expressions of that chemistry. The purpose of this work is to provide the abstraction model to the Performance Assessment Project and the Waste Form Department for development of geochemical models of the waste package interior. The scope of this model report is to describe the development and validation of the in-package chemistry model and in-package chemistry model abstraction. The in-package chemistry model will consider chemical interactions of water with the waste package materials and the waste form for commercial spent nuclear fuel (CSNF) and codisposed high-level waste glass (HLWG) and N Reactor spent fuel (CDNR). The in-package chemistry model includes two sub-models, the first a water vapor condensation (WVC) model, where water enters a waste package as vapor and forms a film on the waste package components with subsequent film reactions with the waste package materials and waste form--this is a no-flow model, the reacted fluids do not exit the waste package via advection. The second sub-model of the in-package chemistry model is the seepage dripping model (SDM), where water, water that may have seeped into the repository from the surrounding rock, enters a failed waste package and reacts with the waste package components and waste form, and then exits the waste package with no accumulation of reacted water in the waste package. Both of the submodels of the in-package chemistry model are film models in contrast to past in-package chemistry models where all of the waste package pore space was filled with water. The

In-Package Chemistry Abstraction

International Nuclear Information System (INIS)

P.S. Domski

2003-01-01

The work associated with the development of this model report was performed in accordance with the requirements established in ''Technical Work Plan for Waste Form Degradation Modeling, Testing, and Analyses in Support of SR and LA'' (BSC 2002a). The in-package chemistry model and in-package chemistry model abstraction are developed to predict the bulk chemistry inside of a failed waste package and to provide simplified expressions of that chemistry. The purpose of this work is to provide the abstraction model to the Performance Assessment Project and the Waste Form Department for development of geochemical models of the waste package interior. The scope of this model report is to describe the development and validation of the in-package chemistry model and in-package chemistry model abstraction. The in-package chemistry model will consider chemical interactions of water with the waste package materials and the waste form for commercial spent nuclear fuel (CSNF) and codisposed high-level waste glass (HLWG) and N Reactor spent fuel (CDNR). The in-package chemistry model includes two sub-models, the first a water vapor condensation (WVC) model, where water enters a waste package as vapor and forms a film on the waste package components with subsequent film reactions with the waste package materials and waste form--this is a no-flow model, the reacted fluids do not exit the waste package via advection. The second sub-model of the in-package chemistry model is the seepage dripping model (SDM), where water, water that may have seeped into the repository from the surrounding rock, enters a failed waste package and reacts with the waste package components and waste form, and then exits the waste package with no accumulation of reacted water in the waste package. Both of the submodels of the in-package chemistry model are film models in contrast to past in-package chemistry models where all of the waste package pore space was filled with water. The current in-package

Advancements in meat packaging.

Science.gov (United States)

McMillin, Kenneth W

2017-10-01

Packaging of meat provides the same or similar benefits for raw chilled and processed meats as other types of food packaging. Although air-permeable packaging is most prevalent for raw chilled red meat, vacuum and modified atmosphere packaging offer longer shelf life. The major advancements in meat packaging have been in the widely used plastic polymers while biobased materials and their integration into composite packaging are receiving much attention for functionality and sustainability. At this time, active and intelligent packaging are not widely used for antioxidant, antimicrobial, and other functions to stabilize and enhance meat properties although many options are being developed and investigated. The advances being made in nanotechnology will be incorporated into food packaging and presumably into meat packaging when appropriate and useful. Intelligent packaging using sensors for transmission of desired information and prompting of subsequent changes in packaging materials, environments or the products to maintain safety and quality are still in developmental stages. Copyright © 2017 Elsevier Ltd. All rights reserved.

Color in packaging design : Case: ZheJiang JinSheng packaging Co,Ltd

OpenAIRE

Hu, Cuicui

2010-01-01

Color occupies an important position in packaging design, with the improvement of living standard, the higher requirement of color design in packaging. The aim of this thesis was to discuss key issues concerning aesthetics of packaging design. Topics will include an overview of the packaging design, the influence factor of packaging design, and introduce the aesthetics from packaging aspect. This thesis will also identify common problems of the production process, and list the phases of ho...

Packaging for Sustainability

CERN Document Server

Lewis, Helen; Fitzpatrick, Leanne

2012-01-01

The packaging industry is under pressure from regulators, customers and other stakeholders to improve packaging’s sustainability by reducing its environmental and societal impacts. This is a considerable challenge because of the complex interactions between products and their packaging, and the many roles that packaging plays in the supply chain. Packaging for Sustainability is a concise and readable handbook for practitioners who are trying to implement sustainability strategies for packaging. Industry case studies are used throughout the book to illustrate possible applications and scenarios. Packaging for Sustainability draws on the expertise of researchers and industry practitioners to provide information on business benefits, environmental issues and priorities, environmental evaluation tools, design for environment, marketing strategies, and challenges for the future.

CDIAC catalog of numeric data packages and computer model packages

International Nuclear Information System (INIS)

Boden, T.A.; Stoss, F.W.

1993-05-01

The Carbon Dioxide Information Analysis Center acquires, quality-assures, and distributes to the scientific community numeric data packages (NDPs) and computer model packages (CMPs) dealing with topics related to atmospheric trace-gas concentrations and global climate change. These packages include data on historic and present atmospheric CO 2 and CH 4 concentrations, historic and present oceanic CO 2 concentrations, historic weather and climate around the world, sea-level rise, storm occurrences, volcanic dust in the atmosphere, sources of atmospheric CO 2 , plants' response to elevated CO 2 levels, sunspot occurrences, and many other indicators of, contributors to, or components of climate change. This catalog describes the packages presently offered by CDIAC, reviews the processes used by CDIAC to assure the quality of the data contained in these packages, notes the media on which each package is available, describes the documentation that accompanies each package, and provides ordering information. Numeric data are available in the printed NDPs and CMPs, in CD-ROM format, and from an anonymous FTP area via Internet. All CDIAC information products are available at no cost

The effect of the textural properties of bituminous coal chars on NO emissions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Pis, J.J.; Jones, J.M.; Williams, A. [CSIC, Oviedo (Spain). Inst. Nacional del Carbon

1999-11-01

NO is the primary product of the oxidation of char nitrogen, and in some combustion processes the NO can be reduced on the char surface to give N{sub 2}O and/or N{sub 2}. In this study a range of bituminous coal (low, medium and high volatile matter content) were pyrolysed in a fixed bed reactor at various heating rates. Textural characterisation was carried out by measuring true (He) and apparent (Hg) densities and N{sub 2} (-196{degree}C) and CO{sub 2} (0{degree}C) adsorption isotherms. Pore volume distributions and surface areas were obtained for the chars studied. A thermogravimetric analyser coupled to a quadrupole mass spectrometer (TG-MS) was used to study the combustion behaviour of the samples and the nitrogen compounds evolved during temperature-programmed combustion. Results are discussed in terms of the influence of both textural properties and reactivity on NO emissions and on the heterogeneous reduction of NO. 23 refs., 8 figs., 4 tabs.

Using proximate analysis to characterize airborne dust generation from bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Page, S.J.; Organiscak, J.A.

2005-11-01

Prolonged exposure to airborne respirable coal dust is responsible for coal workers pneumoconiosis (CWP), commonly called black lung. Health research studies have identified that the prevalence and severity of CWP are directly related to both the amount of dust exposure and the coal rank. The amount of airborne respirable dust (ARD) smaller than 10 micrometers generated from breakage of different coals varies widely. To investigate the cause, researchers for the National Institute for Occupational Safety and Health (NIOSH) have conducted experiments to identify the causes of airborne respirable dust liberation. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals from eight mines. The results indicate that the proximate analysis of a coal sample can provide a very good indicator of the potential for a dust problem. For application to the coal mining, processing, and utilization industries, data from 977 US coal seams compiled by the Department of Energy (DoE) has been used to calculate this dust generation potential from an equation based on the NIOSH measured data. A simple procedure for this calculation is provided. 1 fig.

Trace elemental analysis of bituminous coals using the Heidelberg proton microprobe

Energy Technology Data Exchange (ETDEWEB)

Chen, J R; Kneis, H; Martin, B; Nobiling, R; Traxel, K [Max-Planck-Institut fuer Kernphysik, Heidelberg (Germany, F.R.); Heidelberg Univ. (Germany, F.R.). Physikalisches Inst.); Chao, E C.T.; Minkin, J A [Geological Survey, Reston, VA (USA)

1981-03-01

Trace elements in coal can occur as components of either the organic constituents (macerals) or the inorganic constituents (minerals). Studies of the concentrations and distribution of the trace elements are vital to understanding the geochemical milieu in which the coal was formed and in evaluating the attempts to recover rare but technologically valuable metals. In addition, information on the trace element concentrations is important in predicting the environmental impact of burning particular coals, as many countries move toward greater utilization of coal reserves for energy production. Traditionally, the optical and the electron microscopes and more recently the electron microprobe have been used in studying the components of coal. The proton-induced X-ray emission (PIXE) microprobe offers a new complementary approach with an order of magnitude or more better minimum detection limit. We present the first measurements with a PIXE microprobe of the trace element concentrations of bituminous coal samples. Elemental analyses of the coal macerals-vitrinite, exinite, and inertinite - are discussed for three coal samples from the Eastern U.S.A., three samples from the Western U.S.A., and one sample from the Peoples Republic of China.

On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

Energy Technology Data Exchange (ETDEWEB)

Fischer, Hartmut R., E-mail: hartmut.fischer@tno.nl [TNO Technical Sciences, De Rondom 1, 5612 AP Eindhoven (Netherlands); Dillingh, E.C.; Hermse, C.G.M. [TNO Technical Sciences, De Rondom 1, 5612 AP Eindhoven (Netherlands)

2013-01-15

Highlights: Black-Right-Pointing-Pointer Direct measurement of the contact angle between different phases of the microstructure of bitumen and aggregate surfaces of different chemical nature using AFM. Black-Right-Pointing-Pointer Common schema of adhesion of bitumen on aggregates via asphaltene precipitation. Black-Right-Pointing-Pointer Surface roughness/porosity more important than chemical nature for strength of adhesion between aggregate and bitumen. - Abstract: The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in the micro-structure of bitumen, regardless of differences in their chemical nature. The peri/catana-phase shows a preferential wetting due to adsorption of asphaltene aggregates to the mineral surfaces.

On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

International Nuclear Information System (INIS)

Fischer, Hartmut R.; Dillingh, E.C.; Hermse, C.G.M.

2013-01-01

Highlights: ► Direct measurement of the contact angle between different phases of the microstructure of bitumen and aggregate surfaces of different chemical nature using AFM. ► Common schema of adhesion of bitumen on aggregates via asphaltene precipitation. ► Surface roughness/porosity more important than chemical nature for strength of adhesion between aggregate and bitumen. - Abstract: The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in the micro-structure of bitumen, regardless of differences in their chemical nature. The peri/catana-phase shows a preferential wetting due to adsorption of asphaltene aggregates to the mineral surfaces.

Waste package performance assessment

International Nuclear Information System (INIS)

Lester, D.H.

1981-01-01

This paper describes work undertaken to assess the life-expectancy and post-failure nuclide release behavior of high-level and waste packages in a geologic repository. The work involved integrating models of individual phenomena (such as heat transfer, corrosion, package deformation, and nuclide transport) and using existing data to make estimates of post-emplacement behavior of waste packages. A package performance assessment code was developed to predict time to package failure in a flooded repository and subsequent transport of nuclides out of the leaking package. The model has been used to evaluate preliminary package designs. The results indicate, that within the limitation of model assumptions and data base, packages lasting a few hundreds of years could be developed. Very long lived packages may be possible but more comprehensive data are needed to confirm this

Edible packaging materials.

Science.gov (United States)

Janjarasskul, Theeranun; Krochta, John M

2010-01-01

Research groups and the food and pharmaceutical industries recognize edible packaging as a useful alternative or addition to conventional packaging to reduce waste and to create novel applications for improving product stability, quality, safety, variety, and convenience for consumers. Recent studies have explored the ability of biopolymer-based food packaging materials to carry and control-release active compounds. As diverse edible packaging materials derived from various by-products or waste from food industry are being developed, the dry thermoplastic process is advancing rapidly as a feasible commercial edible packaging manufacturing process. The employment of nanocomposite concepts to edible packaging materials promises to improve barrier and mechanical properties and facilitate effective incorporation of bioactive ingredients and other designed functions. In addition to the need for a more fundamental understanding to enable design to desired specifications, edible packaging has to overcome challenges such as regulatory requirements, consumer acceptance, and scaling-up research concepts to commercial applications.

Active Packaging Coatings

Directory of Open Access Journals (Sweden)

Luis J. Bastarrachea

2015-11-01

Full Text Available Active food packaging involves the packaging of foods with materials that provide an enhanced functionality, such as antimicrobial, antioxidant or biocatalytic functions. This can be achieved through the incorporation of active compounds into the matrix of the commonly used packaging materials, or by the application of coatings with the corresponding functionality through surface modification. The latter option offers the advantage of preserving the packaging materials’ bulk properties nearly intact. Herein, different coating technologies like embedding for controlled release, immobilization, layer-by-layer deposition, and photografting are explained and their potential application for active food packaging is explored and discussed.

Safety Analysis Report for packaging (onsite) steel waste package

International Nuclear Information System (INIS)

BOEHNKE, W.M.

2000-01-01

The steel waste package is used primarily for the shipment of remote-handled radioactive waste from the 324 Building to the 200 Area for interim storage. The steel waste package is authorized for shipment of transuranic isotopes. The maximum allowable radioactive material that is authorized is 500,000 Ci. This exceeds the highway route controlled quantity (3,000 A 2 s) and is a type B packaging

PRIDE Surveillance Projects Data Packaging Project Information Package Specification Version 1.1

Energy Technology Data Exchange (ETDEWEB)

Kelleher, D. M.; Shipp, R. L.; Mason, J. D.

2010-08-31

Information Package Specification version 1.1 describes an XML document format called an information package that can be used to store information in information management systems and other information archives. An information package consists of package information, the context required to understand and use that information, package metadata that describes the information, and XML signatures that protect the information. The information package described in this specification was designed to store Department of Energy (DOE) and National Nuclear Security Administration (NNSA) information and includes the metadata required for that information: a unique package identifier, information marking that conforms to DOE and NNSA requirements, and access control metadata. It is an implementation of the Open Archival Information System (OAIS) Reference Model archival information package tailored to meet NNSA information storage requirements and designed to be used in the computing environments at the Y-12 National Security Complex and at other NNSA sites.

Revue Française de Sciences Politique, n° 5-6, 2012, vol. 62, 300 p.Dossier : Retour sur les situations révolutionnaires arabes

OpenAIRE

Saradouni, Karim

2017-01-01

Ce numéro de la Revue Française de Sciences Politiques est consacré aux situations révolutionnaires dans le Monde arabe. Il se veut un retour sur les différents pays concernés par ce qu’il est convenu d’appeler « révolutions arabes ». Contrairement à la littérature prolixe en sciences sociales sur les causes et les conséquences des révolutions arabes, les contributeurs à ce dossier, interrogent, à partir des enquêtes de terrain, les situations révolutionnaires elles-mêmes et les processus qui...

HPLOT: the graphics interface package for the HBOOK histogramming package

International Nuclear Information System (INIS)

Watkins, H.

1978-01-01

The subroutine package HPLOT described in this report, enables the CERN histogramming package HBOOK to produce high-quality pictures by means of high-resolution devices such as plotters. HPLOT can be implemented on any scientific computing system with a Fortran IV compiler and can be interfaced with any graphics package; spectral routines in addition to the basic ones enable users to embellish their histograms. Examples are also given of the use of HPLOT as a graphics package for plotting simple pictures without histograms. (Auth.)

Bituminization of simulated waste, spent resins, evaporator concentrates and animal ashes by extrusion process

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.

1987-01-01

The results of the study of bituminization of simulated radwaste - spennt ion-exchange resins, borate evaporator/concentrates and animal ashes, are presented and discussed. Distilled and oxidizer bitumen were used. Characterization of the crude material and simulated wastes-bitumen mixtures of varying weigt composition (30, 40, 50, 60% by weight of dry waste material) was carried out. The asphaltene and parafin contents in the bitumens were also determined. Some additives and were used with an aim to improve the characteristcs of solidified wastes. For leaching studies, granular ion-exchange resins were with Cs - 134 and mixtures of resin-bitumen were prepared. The leaching studies were executed using the IAEA recommendation and the ISO method. A conventional screw-extruder, common in plastic industry, was used determine operational parameters and process difficulties. Mixtures of resin-bitumen and evaporator concentrate-bitumen obtained from differents operational conditions were characterized. (Author) [pt

Package

Directory of Open Access Journals (Sweden)

Arsić Zoran

2013-01-01

Full Text Available It is duty of the seller to pack the goods in a manner which assures their safe arrival and enables their handling in transit and at the place of destination. The problem of packing is relevant in two main respects. First of all the buyer is in certain circumstances entitled to refuse acceptance of the goods if they are not properly packed. Second, the package is relevant to calculation of price and freight based on weight. In the case of export trade, the package should conform to the legislation in the country of destination. The impact of package on environment is regulated by environment protection regulation of Republic if Serbia.

Packaging-radiation disinfestation relationships

International Nuclear Information System (INIS)

Highland, H.A.

1985-01-01

Foods that are susceptible to insect infestation can be irradiated to destroy the infestation; however, the food must be kept essentially insect-free until consumed, or it must be disinfested again, perhaps repeatedly. Insect-resistant packages can be used to prevent reinfestation, but there are certain requirements that must be fulfilled before a package can be made insect resistant. These include the use of insect-light construction and packaging materials that resist boring insects. The relative insect resistance of various packages and packaging materials is discussed, as are behavior traits such as egressive boring that enables insects to escape from packages and the ability of insects to climb on various packaging materials. Some successful and unsuccessful attempts to make various types of packages insect resistant are discussed, as are factors that must be considered in the selection or development of insect-resistant packages for radiation disinfested foods. The latter factors include biological and physical environments, length of storage periods, stresses on packages during shipment, types of storage facilities, governmental regulations, health requirements, and others

Packaging Printing Today

Directory of Open Access Journals (Sweden)

Stanislav Bolanča

2015-12-01

Full Text Available Printing packaging covers today about 50% of all the printing products. Among the printing products there are printing on labels, printing on flexible packaging, printing on folding boxes, printing on the boxes of corrugated board, printing on glass packaging, synthetic and metal ones. The mentioned packaging are printed in flexo printing technique, offset printing technique, intaglio halftone process, silk – screen printing, ink ball printing, digital printing and hybrid printing process. The possibilities of particular printing techniques for optimal production of the determined packaging were studied in the paper. The problem was viewed from the technological and economical aspect. The possible printing quality and the time necessary for the printing realization were taken as key parameters. An important segment of the production and the way of life is alocation value and it had also found its place in this paper. The events in the field of packaging printing in the whole world were analyzed. The trends of technique developments and the printing technology for packaging printing in near future were also discussed.

Packaged die heater

Science.gov (United States)

Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

2011-06-21

A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

Safety Analysis Report for packaging (onsite) steel waste package

Energy Technology Data Exchange (ETDEWEB)

BOEHNKE, W.M.

2000-07-13

The steel waste package is used primarily for the shipment of remote-handled radioactive waste from the 324 Building to the 200 Area for interim storage. The steel waste package is authorized for shipment of transuranic isotopes. The maximum allowable radioactive material that is authorized is 500,000 Ci. This exceeds the highway route controlled quantity (3,000 A{sub 2}s) and is a type B packaging.

Packaging Printing Today

OpenAIRE

Stanislav Bolanča; Igor Majnarić; Kristijan Golubović

2015-01-01

Printing packaging covers today about 50% of all the printing products. Among the printing products there are printing on labels, printing on flexible packaging, printing on folding boxes, printing on the boxes of corrugated board, printing on glass packaging, synthetic and metal ones. The mentioned packaging are printed in flexo printing technique, offset printing technique, intaglio halftone process, silk – screen printing, ink ball printing, digital printing and hybrid printing process. T...

Thermal Management of Power Semiconductor Packages - Matching Cooling Technologies with Packaging Technologies (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Bennion, K.; Moreno, G.

2010-04-27

Heat removal for power semiconductor devices is critical for robust operation. Because there are different packaging options, different thermal management technologies, and a range of applications, there is a need for a methodology to match cooling technologies and package configurations to target applications. To meet this need, a methodology was developed to compare the sensitivity of cooling technologies on the overall package thermal performance over a range of power semiconductor packaging configurations. The results provide insight into the trade-offs associated with cooling technologies and package configurations. The approach provides a method for comparing new developments in power semiconductor packages and identifying potential thermal control technologies for the package. The results can help users select the appropriate combination of packaging configuration and cooling technology for the desired application.

NRF TRIGA packaging

International Nuclear Information System (INIS)

Clements, M.D.

1995-11-01

Training Reactor Isotopes, General Atomics (TRIGA reg-sign) Reactors are in use at four US Department of Energy (DOE) complex facilities and at least 23 university, commercial, or government facilities. The development of the Neutron Radiography Facility (NRF) TRIGA packaging system began in October 1993. The Hanford Site NRF is being shut down and requires an operationally user-friendly transportation and storage packaging system for removal of the TRIGA fuel elements. The NRF TRIGA packaging system is designed to remotely remove the fuel from the reactor and transport the fuel to interim storage (up to 50 years) on the Hanford Site. The packaging system consists of a cask and an overpack. The overpack is used only for transport and is not necessary for storage. Based upon the cask's small size and light weight, small TRIGA reactors will find it versatile for numerous refueling and fuel storage needs. The NRF TRIGA packaging design also provides the basis for developing a certifiable and economical packaging system for other TRIGA reactor facilities. The small size of the NRF TRIGA cask also accommodates placing the cask into a larger certified packaging for offsite transport. The Westinghouse Hanford Company NRF TRIGA packaging, as described herein can serve other DOE sites for their onsite use, and the design can be adapted to serve university reactor facilities, handling a variety of fuel payloads

Efecto de la tenacidad del asfalto en la resistencia a fatiga de las mezclas asfálticas Asphalt toughness effect on bituminous mixture fatigue behavior

Directory of Open Access Journals (Sweden)

Alfredo H Noguera

2011-08-01

Full Text Available Uno de los parámetros más importantes para definir el comportamiento de la mezcla en servicio es la tenacidad que el asfalto proporciona al aglomerar los agregados, es decir, la energía que se disipa al fracturar la mezcla, entre mayor sea dicha energía mejor será su calidad. Y por lo tanto, deberá existir una relación si dicha cantidad de energía se disipa en un ciclo de carga (tracción o con muchos ciclos durante el tiempo (fatiga. El objetivo de éste trabajo es establecer una relación entre la tenacidad que ofrecen distintos asfaltos y el comportamiento a fatiga de sus correspondientes mezclas asfálticas, para lo cual, se ha obtenido la tenacidad mediante un ensayo de tracción directa y se ha comparado con los valores de las leyes de fatiga y energía disipada obtenidas del ensayo de flexo-tracción dinámica.One of the most important parameters to define bituminous mixture behavior in service is the toughness that the bitumen provides when binding the aggregate particles; that is; the dissipated energy during the materials fracture process. The greater the dissipated energy in fracture, the better the bituminous mixture quality is. Hence, a relationship will have to exist if the toughness is removed during one load cycle (direct tension or during many cycles along time (fatigue. The purpose of this study is to determinate relationships between the toughness of different bitumens and the fatigue behavior of their corresponding bituminous mixtures, for which, the toughness has been obtained by means of direct tension test and has been compared with the value of the fatigue law and dissipated energy obtained by fatigue bending test. Results showed that, this study expect to give important means for further research to predict fatigue life from a static test.

Packaging for Food Service

Science.gov (United States)

Stilwell, E. J.

1985-01-01

Most of the key areas of concern in packaging the three principle food forms for the space station were covered. It can be generally concluded that there are no significant voids in packaging materials availability or in current packaging technology. However, it must also be concluded that the process by which packaging decisions are made for the space station feeding program will be very synergistic. Packaging selection will depend heavily on the preparation mechanics, the preferred presentation and the achievable disposal systems. It will be important that packaging be considered as an integral part of each decision as these systems are developed.

Waste Package Lifting Calculation

International Nuclear Information System (INIS)

H. Marr

2000-01-01

The objective of this calculation is to evaluate the structural response of the waste package during the horizontal and vertical lifting operations in order to support the waste package lifting feature design. The scope of this calculation includes the evaluation of the 21 PWR UCF (pressurized water reactor uncanistered fuel) waste package, naval waste package, 5 DHLW/DOE SNF (defense high-level waste/Department of Energy spent nuclear fuel)--short waste package, and 44 BWR (boiling water reactor) UCF waste package. Procedure AP-3.12Q, Revision 0, ICN 0, calculations, is used to develop and document this calculation

Certification of packagings: compliance with DOT specification 7A packaging requirements

International Nuclear Information System (INIS)

Edling, D.A.

1976-01-01

A study was conducted to determine which of the packagings currently listed in CFR 49 Section 173.395 a.1-5, meet the Specification 7A requirements (CFR 49 Section 173.350). According to DOT HM-111 the present listing of various authorized DOT specifications in Section 173.394 and Section 173.395 (Type A containers) of ICC Tariff No. 27 would be deleted with complete reliance being placed on the use of DOT 7A, Type A general packaging specification. Each user of a Specification 7A package would be required to document and maintain on file for one year a written record of his determination of compliance with the DOT Specification 7A performance requirements. All the specification packagings listed in CFR 49 Section 173.395a.1-5 were tested and shown to meet the Specification 7A criteria; however, in many cases qualifications were placed on their use. Forty-nine specification packagings were tested and shown to meet the DOT Specification 7A performance requirements and since there were several styles of some specific packagings, this amounts to greater than 80 packagings. The extensive testing generally indicated a high degree of containment integrity in the packagings tested and the documentation discussed is a valuable tool for shippers of Type A quantities of radioactive materials

Distillation of shale and other bituminous substances. [shale granules wetted, mixed with lime, heated; sulfur recovered

Energy Technology Data Exchange (ETDEWEB)

Noad, J

1912-09-23

A process is described for the treatment of shale and other bituminous substances containing sulfur and recovering desulfurized distillates. The process consists of first grinding the shale and mixing the granules obtained with a convenient liquid. The shale granules coated or covered with liquid and mixed with slacked lime are fed into a retort with a series of steps or their equivalent, made to descend, step by step, in such manner that they are continually agitated and heated. The volatile constituents escape through the coating or sheath of lime and are carried away at the upper part of the retort to a convenient condensing apparatus, the sulfur being retained by the sheath of lime and is discharged at the bottom of the retort with the spent shale and other impurities.

Report on the final evaluation on the 'development of a bituminous coal liquefaction technology (NEDOL method)' in the Sunshine Project; Rekiseitan ekika gijutsu (NEDOL ho) kaihatsu saishu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

Development of a bituminous coal liquefaction technology (NEDOL method) can be judged appropriate as a national project in the comprehensive view with the 21st century just around the corner. It is a fact that this project has spent the national budget not in a small amount. There is no prospect of the technology to be put into practical use in Japan at the present time. The coal liquefaction technology is a technology required inevitably in the situation where shortage of crude oil supply may endanger the existence of a nation. Therefore, there is sufficient significance in having demonstrated the effectiveness of the NEDOL method which can be applied to a large number of coal types and expected of high liquefaction yield. The contents of the 'technological package' to be prepared are so demanded that its usefulness can be retained until the time of a demonstration plant design and operation will come in the future. It is also desired that the human resources and the testing devices will be kept ensured, and the technologies developed under this project will be maintained and expanded. The present technology has low necessity of immediately putting into practical use in Japan at the present time. However, the technology should be kept available for use at any time, and retained for use in an urgent situation. (NEDO)

Dossier: Introducción ¿Hacia dónde se dirige el Sindicalismo en Argentina y Brasil?

Directory of Open Access Journals (Sweden)

Juan Montes Cató

2016-07-01

Full Text Available Las transformaciones sociopolíticas que atravesó América del Sur desde la década de los 2000, a partir del vuelco de muchos de los gobiernos hacia posturas progresistas y de las muestras de agotamiento del modelo neoliberal se plantean como un desafío a las prácticas y estrategias de las organizaciones obreras en cuanto articuladoras de las demandas de los trabajadores. Estos desafíos asumen proyecciones diferentes en función de las características socioeconómicas de los países, de las tradiciónes de las organizaciones sindicales, de la relación con otros movimientos sociales y políticos y también en el modo en que se estructuran las relaciones hacia el interior del propio sujeto colectivo. Es en la intersección de estas preocupaciones que el Dossier que aquí presentamos adquiere relevancia en cuanto busca actualizar críticamente los debates al discutir los marcos interpretativos desde los cuales fueron pensados los fenómenos sindicales latinoamericanos y comprender las tendencias que vienen operando en largo y mediano plazo en la región del Cono Sur de América en especial retomando los procesos de Argentina y Brasil.

Anhydrous Ammonia Training Module. Trainer's Package. Participant's Package.

Science.gov (United States)

Beaudin, Bart; And Others

This document contains a trainer's and a participant's package for teaching employees on site safe handling procedures for working with anhydrous ammonia, especially on farms. The trainer's package includes the following: a description of the module; a competency; objectives; suggested instructional aids; a training outline (or lesson plan) for…

Green Packaging Development. : A way to efficient, effective and more environmental friendly packaging solutions.

OpenAIRE

Mian Muhammad, Masoud

2011-01-01

Growing pressure on the packaging design to enhance the environmental and logistics performance of a packaging system stresses the packaging designers to search new design strategies that not only fulfill logistics requirements in the supply chain, but also reduce the CO 2emissions during the packaging life cycle. This thesis focuses on the packaging design process and suggests some improvements by considering its logistics performance and CO 2emissions. A Green packaging development model wa...

Relation Between Bitumen Content and Percentage Air Voids in Semi Dense Bituminous Concrete

Science.gov (United States)

Panda, R. P.; Das, Sudhanshu Sekhar; Sahoo, P. K.

2018-06-01

Hot mix asphalt (HMA) is a heterogeneous mix of aggregate, mineral filler, bitumen, additives and air voids. Researchers have indicated that the durability of the HMA is sensitive on the actual bitumen content and percentage air void. This paper aims at establishing the relationship between the bitumen content and the percentage air voids in Semi Dense Bituminous Concrete (SDBC) using Viscosity Grade-30 (VG-30) bitumen. Total 54 samples have been collected, for formulation and validation of relationship and observed that the percentage air voids increases with decrease in actual bitumen content and vice versa. A minor increase in percentage air voids beyond practice of designed air voids in Marshall Method of design is required for better performance, indicating a need for reducing the codal provision of minimum bitumen content for SDBC as specified in Specification for Road & Bridges (Fourth Revision) published by Indian Road Congress, 2001. The study shows a possibility of reducing designed minimum bitumen content from codal provision for SDBC by 0.2% of weight with VG-30 grade of Bitumen.

Continuous distillation of bituminous shale. [hot gas in chamber and chamber heated externally

Energy Technology Data Exchange (ETDEWEB)

1921-04-27

A process of continuous distillation of bituminous shale is given in which the heat necessary is produced not only on the exterior but also in the interior of the distillation apparatus in the form of hot gas directly bathing the shale. The residual carbon in the shale after distillation, or maybe with other fuel added to it, can be utilized; the fuel may be utilized not only for the heat it furnishes but also for the gas it gives and which adds itself to the incondensable gas from the distillation. The temperature of the zone of distillation of the shale is regulated by the quantity of gas, the temperature of this gas (which can be lowered voluntarily by injecting into the air a certain quantity of water vapor), the length of the zone comprised between the zone of gasification and distillation; the injection of water vapor permits the recovery of part of the nitrogen of the shale in the form of ammonia; the materials are withdrawn continuously in a mechanical way.

Effect of processing on the rheological properties of poly-urethane/urea bituminous products

Energy Technology Data Exchange (ETDEWEB)

Carrera, V.; Partal, P.; Garcia-Morales, M.; Gallegos, C. [Dpto. Ingenieria Quimica, Facultad de Ciencias Experimentales, Campus de ' El Carmen' , Universidad de Huelva, 21071, Huelva (Spain); Perez-Lepe, A. [Technology Centre REPSOL YPF. Road N-V, Km 8, 28931, Mostoles (Spain)

2010-09-15

In this work, bitumen modification, by ''in situ'' formation of poly-urethane/urea-based polymers in the bituminous matrix, has been studied. This procedure consisted of a first modification by the addition of MDI-PPG reactive prepolymer (polypropylene-glycol, PPG, functionalized by polymeric MDI, 4,4'-diphenylmethane diisocyanate), in a first stage, and a further modification of the new bitumen-MDI-PPG molecules as water was added, in a second stage. Thin layer chromatography, TLC-FID, and infrared spectroscopy, FTIR, techniques have been used to follow the reactions occurring in four different types of bitumen. Rheological measurements have demonstrated that the resulting bitumen modification strongly depends on the processing conditions selected during the first stage. Thus, bitumen modification degree after water addition increases as processing time does. Furthermore, water addition has been found to promote bitumen foaming at low processing temperatures, which could be used in novel applications where a foamed binder is required. As a result, a reactive bitumen modification mechanism, involving a set of three chemical reactions, has been proposed. (author)

Relation Between Bitumen Content and Percentage Air Voids in Semi Dense Bituminous Concrete

Science.gov (United States)

Panda, R. P.; Das, Sudhanshu Sekhar; Sahoo, P. K.

2018-02-01

Hot mix asphalt (HMA) is a heterogeneous mix of aggregate, mineral filler, bitumen, additives and air voids. Researchers have indicated that the durability of the HMA is sensitive on the actual bitumen content and percentage air void. This paper aims at establishing the relationship between the bitumen content and the percentage air voids in Semi Dense Bituminous Concrete (SDBC) using Viscosity Grade-30 (VG-30) bitumen. Total 54 samples have been collected, for formulation and validation of relationship and observed that the percentage air voids increases with decrease in actual bitumen content and vice versa. A minor increase in percentage air voids beyond practice of designed air voids in Marshall Method of design is required for better performance, indicating a need for reducing the codal provision of minimum bitumen content for SDBC as specified in Specification for Road & Bridges (Fourth Revision) published by Indian Road Congress, 2001. The study shows a possibility of reducing designed minimum bitumen content from codal provision for SDBC by 0.2% of weight with VG-30 grade of Bitumen.

Characteristic Study of Shenmu Bituminous Coal Combustion with Online TG-MS-FTIR

Science.gov (United States)

Pan, Guanfu

2018-01-01

The combustion characteristics of Shenmu bituminous pulverized coal (SBC) were comprehensively investigated with a combined TG-MS-FTIR system by considering the effect of particle size, heating rate and total flowrate. The combustion products were accurately quantified by normalization and numerical analysis of MS results. The results indicate that the decrease of the particle size, heating rate and total flowrate result in lower ignition and burnout temperatures. The activation energy tends to be lower with smaller particle size, lower heating rate and total flowrate. The MS and FTIR results demonstrate that lower concentrations of different products, such as NO, NO2, HCN, CH4 and SO2 were produced with smaller particle size, slower heating rate and lower total flowrate. The decrease of particle size would lead to more contact area with oxygen and slower heating rate could provide more sufficient time for the diffusion. High total flowrate would reduce the oxygen adsorbability on the coal particle surface and shorten the residence time of oxygen, which makes the ignition difficult to occur. This work will guide to understand the combustion kinetics of pulverized coals and be beneficial to control the formation of pollutants.

Fixation of calcined waste by bituminization or cementation

International Nuclear Information System (INIS)

Napravnik, J.; Kyrs, M.; Ditl, P.

1983-01-01

The overall concept is given of the combination of calcination with fixation into bitumen, cement etc. The design is shown of a calciner with the capacity of 10 L/h which was tested on real radioactive wastes for 2000 h. The geometrical and operating parameters of the apparatus have been optimized based on a statistical evaluation of the experiments. Wastes containing nitrates are calcined at 300-550 deg. C, yielding oxides. Wastes containing sulphates, carbonates, KMnO 4 , or borates are calcined at 150-330 deg. C, yielding soluble salts. The content of H 3 BO 4 and Na 2 B 4 O 7 and in some cases of sulphates in the calcinate retards hardening of the mixture with cement. Nitrates and detergents also interfere. The effect of the above components on the products mixed with bitumen is much less. Detergents can be decomposed at 200-300 deg. C; organic acids can be reacted with A1 salts to form insoluble substances lowering the leaching rate of Sr and Cs; small amounts of SiO 2 eliminate the effect of borates on cement hardening. The drawbacks of bituminization with bitumen emulsions are the complicated preparation of the emulsion, higher leaching rate of the product and low stability of the emulsion against breaking. The leachability was determined (1-50 days) of different products containing LWR wastes: 33% of concentrated waste in cement of calcination product stabilized with PVA exhibit approx. 8x10 - 3 g/cm 2 per day, 33% of calcine in cement approx. 3x10 - 3 ; 40% concentrate fixed with bitumen emulsion approx. 9x10 - 4 ; 50% calcine stabilized with PVA in bitumen, pilot-plant scale approx. 2x10 - 5 ; the same but on a laboratory scale approx. 1.10 - 5 . (author)

IN-PACKAGE CHEMISTRY ABSTRACTION

Energy Technology Data Exchange (ETDEWEB)

E. Thomas

2005-07-14

This report was developed in accordance with the requirements in ''Technical Work Plan for Postclosure Waste Form Modeling'' (BSC 2005 [DIRS 173246]). The purpose of the in-package chemistry model is to predict the bulk chemistry inside of a breached waste package and to provide simplified expressions of that chemistry as a function of time after breach to Total Systems Performance Assessment for the License Application (TSPA-LA). The scope of this report is to describe the development and validation of the in-package chemistry model. The in-package model is a combination of two models, a batch reactor model, which uses the EQ3/6 geochemistry-modeling tool, and a surface complexation model, which is applied to the results of the batch reactor model. The batch reactor model considers chemical interactions of water with the waste package materials, and the waste form for commercial spent nuclear fuel (CSNF) waste packages and codisposed (CDSP) waste packages containing high-level waste glass (HLWG) and DOE spent fuel. The surface complexation model includes the impact of fluid-surface interactions (i.e., surface complexation) on the resulting fluid composition. The model examines two types of water influx: (1) the condensation of water vapor diffusing into the waste package, and (2) seepage water entering the waste package as a liquid from the drift. (1) Vapor-Influx Case: The condensation of vapor onto the waste package internals is simulated as pure H{sub 2}O and enters at a rate determined by the water vapor pressure for representative temperature and relative humidity conditions. (2) Liquid-Influx Case: The water entering a waste package from the drift is simulated as typical groundwater and enters at a rate determined by the amount of seepage available to flow through openings in a breached waste package.

IN-PACKAGE CHEMISTRY ABSTRACTION

International Nuclear Information System (INIS)

E. Thomas

2005-01-01

This report was developed in accordance with the requirements in ''Technical Work Plan for Postclosure Waste Form Modeling'' (BSC 2005 [DIRS 173246]). The purpose of the in-package chemistry model is to predict the bulk chemistry inside of a breached waste package and to provide simplified expressions of that chemistry as a function of time after breach to Total Systems Performance Assessment for the License Application (TSPA-LA). The scope of this report is to describe the development and validation of the in-package chemistry model. The in-package model is a combination of two models, a batch reactor model, which uses the EQ3/6 geochemistry-modeling tool, and a surface complexation model, which is applied to the results of the batch reactor model. The batch reactor model considers chemical interactions of water with the waste package materials, and the waste form for commercial spent nuclear fuel (CSNF) waste packages and codisposed (CDSP) waste packages containing high-level waste glass (HLWG) and DOE spent fuel. The surface complexation model includes the impact of fluid-surface interactions (i.e., surface complexation) on the resulting fluid composition. The model examines two types of water influx: (1) the condensation of water vapor diffusing into the waste package, and (2) seepage water entering the waste package as a liquid from the drift. (1) Vapor-Influx Case: The condensation of vapor onto the waste package internals is simulated as pure H 2 O and enters at a rate determined by the water vapor pressure for representative temperature and relative humidity conditions. (2) Liquid-Influx Case: The water entering a waste package from the drift is simulated as typical groundwater and enters at a rate determined by the amount of seepage available to flow through openings in a breached waste package

Hazardous materials package performance regulations

International Nuclear Information System (INIS)

Russell, N.A.; Glass, R.E.; McClure, J.D.; Finley, N.C.

1992-01-01

The hazardous materials (hazmat) packaging development and certification process is currently defined by two different regulatory philosophies, one based on specification packagings and the other based on performance standards. With specification packagings, a packaging is constructed according to an agreed set of design specifications. In contrast, performance standards do not specify the packaging design; they specify performance standards that a packaging design must be able to pass before it can be certified for transport. The packaging can be designed according to individual needs as long as it meets these performance standards. Performance standards have been used nationally and internationally for about 40 years to certify radioactive materials (RAM) packagings. It is reasonable to state that for RAM transport, performance specifications have maintained transport safety. A committee of United Nation's experts recommended the performance standard philosophy as the preferred regulation method for hazmat packaging. Performance standards for hazmat packagings smaller than 118 gallons have been adopted in 49CFR178. Packagings for materials that are classified as toxic-by-inhalation must comply with the performance standards by October 1, 1993, and packagings for all other classes of hazardous materials covered must comply by October 1, 1996. For packages containing bulk (in excess of 188 gallons) quantities of materials that are extremely toxic by inhalation, there currently are no performance requirements. This paper discusses a Hazmat Packaging Performance Evaluation (HPPE) project to look at the subset of bulk packagings that are larger than 2000 gallons. The objectives of this project are the evaluate current hazmat specification packagings and develop supporting documentation for determining performance requirements for packagings in excess of 2000 gallons that transport hazardous materials that have been classified as extremely toxic by inhalation (METBI)

Lithium niobate packaging challenges

International Nuclear Information System (INIS)

Murphy, E.J.; Holmes, R.J.; Jander, R.B.; Schelling, A.W.

1988-01-01

The use of lithium niobate integrated optic devices outside of the research laboratory is predicated on the development of a sound packaging method. The authors present a discussion of the many issues that face the development of a viable, robust packaging technology. The authors emphasize the interaction of lithium niobate's physical properties with available packaging materials and technologies. The broad range of properties (i.e. electro-optic, piezo-electric, pyro-electric, photorefractive...) that make lithium niobate an interesting material in many device applications also make it a packaging challenge. The package design, materials and packaging technologies must isolate the device from the environment so that lithium niobate's properties do not adversely affect the device performance

User friendly packaging

DEFF Research Database (Denmark)

Geert Jensen, Birgitte

2010-01-01

Most consumers have experienced occasional problems with opening packaging. Tomato sauce from the tinned mackerel splattered all over the kitchen counter, the unrelenting pickle jar lid, and the package of sliced ham that cannot be opened without a knife or a pair of scissors. The research project...... “User-friendly Packaging” aims to create a platform for developing more user-friendly packaging. One intended outcome of the project is a guideline that industry can use in development efforts. The project also points the way for more extended collaboration between companies and design researchers. How...... can design research help industry in packaging innovation?...

Packaging Review Guide for Reviewing Safety Analysis Reports for Packagings

Energy Technology Data Exchange (ETDEWEB)

DiSabatino, A; Biswas, D; DeMicco, M; Fisher, L E; Hafner, R; Haslam, J; Mok, G; Patel, C; Russell, E

2007-04-12

This Packaging Review Guide (PRG) provides guidance for Department of Energy (DOE) review and approval of packagings to transport fissile and Type B quantities of radioactive material. It fulfills, in part, the requirements of DOE Order 460.1B for the Headquarters Certifying Official to establish standards and to provide guidance for the preparation of Safety Analysis Reports for Packagings (SARPs). This PRG is intended for use by the Headquarters Certifying Official and his or her review staff, DOE Secretarial offices, operations/field offices, and applicants for DOE packaging approval. This PRG is generally organized at the section level in a format similar to that recommended in Regulatory Guide 7.9 (RG 7.9). One notable exception is the addition of Section 9 (Quality Assurance), which is not included as a separate chapter in RG 7.9. Within each section, this PRG addresses the technical and regulatory bases for the review, the manner in which the review is accomplished, and findings that are generally applicable for a package that meets the approval standards. This Packaging Review Guide (PRG) provides guidance for DOE review and approval of packagings to transport fissile and Type B quantities of radioactive material. It fulfills, in part, the requirements of DOE O 460.1B for the Headquarters Certifying Official to establish standards and to provide guidance for the preparation of Safety Analysis Reports for Packagings (SARPs). This PRG is intended for use by the Headquarters Certifying Official and his review staff, DOE Secretarial offices, operations/field offices, and applicants for DOE packaging approval. The primary objectives of this PRG are to: (1) Summarize the regulatory requirements for package approval; (2) Describe the technical review procedures by which DOE determines that these requirements have been satisfied; (3) Establish and maintain the quality and uniformity of reviews; (4) Define the base from which to evaluate proposed changes in scope

DNA Packaging by λ-Like Bacteriophages: Mutations Broadening the Packaging Specificity of Terminase, the λ-Packaging Enzyme

OpenAIRE

Feiss, Michael; Reynolds, Erin; Schrock, Morgan; Sippy, Jean

2010-01-01

The DNA-packaging specificities of phages λ and 21 depend on the specific DNA interactions of the small terminase subunits, which have support helix-turn-recognition helix-wing DNA-binding motifs. λ-Terminase with the recognition helix of 21 preferentially packages 21 DNA. This chimeric terminase's ability to package λDNA is reduced ∼20-fold. Phage λ with the chimeric terminase is unable to form plaques, but pseudorevertants are readily obtained. Some pseudorevertants have trans-acting suppre...

The paradox of packaging optimization – a characterization of packaging source reduction in the Netherlands

NARCIS (Netherlands)

van Sluisveld, M.A.E.; Worrell, E.

2013-01-01

The European Council Directive 94/62/EC for Packaging and Packaging Waste requires that Member States implement packaging waste prevention measures. However, consumption and subsequently packaging waste figures are still growing annually. It suggests that policies to accomplish packaging waste

Prevention policies addressing packaging and packaging waste: Some emerging trends.

Science.gov (United States)

Tencati, Antonio; Pogutz, Stefano; Moda, Beatrice; Brambilla, Matteo; Cacia, Claudia

2016-10-01

Packaging waste is a major issue in several countries. Representing in industrialized countries around 30-35% of municipal solid waste yearly generated, this waste stream has steadily grown over the years even if, especially in Europe, specific recycling and recovery targets have been fixed. Therefore, an increasing attention starts to be devoted to prevention measures and interventions. Filling a gap in the current literature, this explorative paper is a first attempt to map the increasingly important phenomenon of prevention policies in the packaging sector. Through a theoretical sampling, 11 countries/states (7 in and 4 outside Europe) have been selected and analyzed by gathering and studying primary and secondary data. Results show evidence of three specific trends in packaging waste prevention policies: fostering the adoption of measures directed at improving packaging design and production through an extensive use of the life cycle assessment; raising the awareness of final consumers by increasing the accountability of firms; promoting collaborative efforts along the packaging supply chains. Copyright © 2016 Elsevier Ltd. All rights reserved.

Food packages for Space Shuttle

Science.gov (United States)

Fohey, M. F.; Sauer, R. L.; Westover, J. B.; Rockafeller, E. F.

1978-01-01

The paper reviews food packaging techniques used in space flight missions and describes the system developed for the Space Shuttle. Attention is directed to bite-size food cubes used in Gemini, Gemini rehydratable food packages, Apollo spoon-bowl rehydratable packages, thermostabilized flex pouch for Apollo, tear-top commercial food cans used in Skylab, polyethylene beverage containers, Skylab rehydratable food package, Space Shuttle food package configuration, duck-bill septum rehydration device, and a drinking/dispensing nozzle for Space Shuttle liquids. Constraints and testing of packaging is considered, a comparison of food package materials is presented, and typical Shuttle foods and beverages are listed.

In-Package Chemistry Abstraction

Energy Technology Data Exchange (ETDEWEB)

E. Thomas

2004-11-09

This report was developed in accordance with the requirements in ''Technical Work Plan for: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]). The purpose of the in-package chemistry model is to predict the bulk chemistry inside of a breached waste package and to provide simplified expressions of that chemistry as function of time after breach to Total Systems Performance Assessment for the License Application (TSPA-LA). The scope of this report is to describe the development and validation of the in-package chemistry model. The in-package model is a combination of two models, a batch reactor model that uses the EQ3/6 geochemistry-modeling tool, and a surface complexation model that is applied to the results of the batch reactor model. The batch reactor model considers chemical interactions of water with the waste package materials and the waste form for commercial spent nuclear fuel (CSNF) waste packages and codisposed waste packages that contain both high-level waste glass (HLWG) and DOE spent fuel. The surface complexation model includes the impact of fluid-surface interactions (i.e., surface complexation) on the resulting fluid composition. The model examines two types of water influx: (1) the condensation of water vapor that diffuses into the waste package, and (2) seepage water that enters the waste package from the drift as a liquid. (1) Vapor Influx Case: The condensation of vapor onto the waste package internals is simulated as pure H2O and enters at a rate determined by the water vapor pressure for representative temperature and relative humidity conditions. (2) Water Influx Case: The water entering a waste package from the drift is simulated as typical groundwater and enters at a rate determined by the amount of seepage available to flow through openings in a breached waste package. TSPA-LA uses the vapor influx case for the nominal scenario for simulations where the waste

In-Package Chemistry Abstraction

International Nuclear Information System (INIS)

E. Thomas

2004-01-01

This report was developed in accordance with the requirements in ''Technical Work Plan for: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]). The purpose of the in-package chemistry model is to predict the bulk chemistry inside of a breached waste package and to provide simplified expressions of that chemistry as function of time after breach to Total Systems Performance Assessment for the License Application (TSPA-LA). The scope of this report is to describe the development and validation of the in-package chemistry model. The in-package model is a combination of two models, a batch reactor model that uses the EQ3/6 geochemistry-modeling tool, and a surface complexation model that is applied to the results of the batch reactor model. The batch reactor model considers chemical interactions of water with the waste package materials and the waste form for commercial spent nuclear fuel (CSNF) waste packages and codisposed waste packages that contain both high-level waste glass (HLWG) and DOE spent fuel. The surface complexation model includes the impact of fluid-surface interactions (i.e., surface complexation) on the resulting fluid composition. The model examines two types of water influx: (1) the condensation of water vapor that diffuses into the waste package, and (2) seepage water that enters the waste package from the drift as a liquid. (1) Vapor Influx Case: The condensation of vapor onto the waste package internals is simulated as pure H2O and enters at a rate determined by the water vapor pressure for representative temperature and relative humidity conditions. (2) Water Influx Case: The water entering a waste package from the drift is simulated as typical groundwater and enters at a rate determined by the amount of seepage available to flow through openings in a breached waste package. TSPA-LA uses the vapor influx case for the nominal scenario for simulations where the waste package has been

Radioactive material packaging performance testing

International Nuclear Information System (INIS)

Romano, T.; Cruse, J.M.

1991-02-01

To provide uniform packaging of hazardous materials on an international level, the United Nations has developed packaging recommendations that have been implemented worldwide. The United Nations packaging recommendations are performance oriented, allowing for a wide variety of package materials and systems. As a result of this international standard, efforts in the United States are being directed toward use of performance-oriented packaging and elimination of specification (designed) packaging. This presentation will focus on trends, design evaluation, and performance testing of radioactive material packaging. The impacts of US Department of Transportation Dockets HM-181 and HM-169A on specification and low-specific activity radioactive material packaging requirements are briefly discussed. The US Department of Energy's program for evaluating radioactive material packings per US Department of Transportation Specification 7A Type A requirements, is used as the basis for discussing low-activity packaging performance test requirements. High-activity package testing requirements are presented with examples of testing performed at the Hanford Site that is operated by Westinghouse Hanford Company for the US Department of Energy. 5 refs., 2 tabs

Experimental and theoretical analyses of package-on-package structure under three-point bending loading

International Nuclear Information System (INIS)

Jia Su; Wang Xi-Shu; Ren Huai-Hui

2012-01-01

High density packaging is developing toward miniaturization and integration, which causes many difficulties in designing, manufacturing, and reliability testing. Package-on-Package (PoP) is a promising three-dimensional high-density packaging method that integrates a chip scale package (CSP) in the top package and a fine-pitch ball grid array (FBGA) in the bottom package. In this paper, in-situ scanning electron microscopy (SEM) observation is carried out to detect the deformation and damage of the PoP structure under three-point bending loading. The results indicate that the cracks occur in the die of the top package, then cause the crack deflection and bridging in the die attaching layer. Furthermore, the mechanical principles are used to analyse the cracking process of the PoP structure based on the multi-layer laminating hypothesis and the theoretical analysis results are found to be in good agreement with the experimental results. (condensed matter: structural, mechanical, and thermal properties)

Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; MacPhee, J.A.; Vancea, L.; Ciavaglia, L.A.; Nandi, B.N.

1983-04-01

Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500 C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by N.M.R. and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars. (19 refs.)

Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Ciavaglia, L.A.; MacPhee, J.A.; Nandi, B.N.; Vancea, L.

1983-04-01

Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500/sup 0/C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by n.m.r., and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars.

WASTE PACKAGE TRANSPORTER DESIGN

International Nuclear Information System (INIS)

Weddle, D.C.; Novotny, R.; Cron, J.

1998-01-01

The purpose of this Design Analysis is to develop preliminary design of the waste package transporter used for waste package (WP) transport and related functions in the subsurface repository. This analysis refines the conceptual design that was started in Phase I of the Viability Assessment. This analysis supports the development of a reliable emplacement concept and a retrieval concept for license application design. The scope of this analysis includes the following activities: (1) Assess features of the transporter design and evaluate alternative design solutions for mechanical components. (2) Develop mechanical equipment details for the transporter. (3) Prepare a preliminary structural evaluation for the transporter. (4) Identify and recommend the equipment design for waste package transport and related functions. (5) Investigate transport equipment interface tolerances. This analysis supports the development of the waste package transporter for the transport, emplacement, and retrieval of packaged radioactive waste forms in the subsurface repository. Once the waste containers are closed and accepted, the packaged radioactive waste forms are termed waste packages (WP). This terminology was finalized as this analysis neared completion; therefore, the term disposal container is used in several references (i.e., the System Description Document (SDD)) (Ref. 5.6). In this analysis and the applicable reference documents, the term ''disposal container'' is synonymous with ''waste package''

Effect of mix parameters on longevity of bituminous mixtures

Science.gov (United States)

Reichle, Clayton Matthew

This study was performed to evaluate the effects of varying aggregate sources, aggregate gradations on the stripping and rutting potential of bituminous based plant mixes specified by the Missouri Department of Transportation. The different aggregate combinations included two different aggregate sources (Potosi Dolomite and Jefferson City Dolomite) including two variations for the Jefferson City Dolomite mix to simulate a marginally in-specification mix and an out-of-specification but in-field tolerance mix. The "field" mix simulated the marginal mix where field tolerance of high dust and low binder content were maximized. All three mixes were evaluated for stripping susceptibility using the Tensile Strength Ratio (TSR) test and the Hamburg Wheel Tracking Device (HWTD). The mix characteristics (unit weight, effective binder content, and air voids) were used for a Level 3 analysis in the Mechanistic-Empirical Pavement Design Guide (MEPDG) to determine long term pavement distress conditions such as fatigue cracking, rutting, and IRI (smoothness). The Potosi mix exhibited the best resistance to rutting and stripping during both the TSR testing as well as the Hamburg testing. The Jefferson City In-Spec and Out-of-Spec mixes showed less resistance to rutting and stripping in order, respectively. This was expected for the Jefferson City mixes where the aggregate was of lower quality (higher Los Angeles Abrasion, Micro Deval loss, absorption, and deleterious materials). Also, in the case of the Jefferson City Out-of-Spec mix, the binder content was lower. Upon evaluating the mixes using the MEPDG software, it was shown that mix characteristics such as air voids, VMA, and VFA influenced the fatigue cracking, rutting, and IRI predictions to a minor degree.

Components of Adenovirus Genome Packaging

Science.gov (United States)

Ahi, Yadvinder S.; Mittal, Suresh K.

2016-01-01

Adenoviruses (AdVs) are icosahedral viruses with double-stranded DNA (dsDNA) genomes. Genome packaging in AdV is thought to be similar to that seen in dsDNA containing icosahedral bacteriophages and herpesviruses. Specific recognition of the AdV genome is mediated by a packaging domain located close to the left end of the viral genome and is mediated by the viral packaging machinery. Our understanding of the role of various components of the viral packaging machinery in AdV genome packaging has greatly advanced in recent years. Characterization of empty capsids assembled in the absence of one or more components involved in packaging, identification of the unique vertex, and demonstration of the role of IVa2, the putative packaging ATPase, in genome packaging have provided compelling evidence that AdVs follow a sequential assembly pathway. This review provides a detailed discussion on the functions of the various viral and cellular factors involved in AdV genome packaging. We conclude by briefly discussing the roles of the empty capsids, assembly intermediates, scaffolding proteins, portal vertex and DNA encapsidating enzymes in AdV assembly and packaging. PMID:27721809

Co-gasification of bituminous coal and hydrochar derived from municipal solid waste: Reactivity and synergy.

Science.gov (United States)

Wei, Juntao; Guo, Qinghua; He, Qing; Ding, Lu; Yoshikawa, Kunio; Yu, Guangsuo

2017-09-01

In this work, the influences of gasification temperature and blended ratio on co-gasification reactivity and synergy of Shenfu bituminous coal (SF) and municipal solid waste-derived hydrochar (HTC) were investigated using TGA. Additionally, active alkaline and alkaline earth metal (AAEM) transformation during co-gasification was quantitatively analyzed by inductively coupled plasma optical emission spectrometer for correlating synergy on co-gasification reactivity. The results showed that higher char gasification reactivity existed at higher HTC char proportion and gasification temperature, and the main synergy behaviour on co-gasification reactivity was performed as synergistic effect. Enhanced synergistic effect at lower temperature was mainly resulted from more obviously inhibiting the primary AAEM (i.e. active Ca) transformation, and weak synergistic effect still existed at higher temperature since more active K with prominent catalysis was retained. Furthermore, more active HTC-derived AAEM remaining in SF sample during co-gasification would lead to enhanced synergistic effect as HTC char proportion increased. Copyright © 2017 Elsevier Ltd. All rights reserved.

Technical and economic assessment of process of treatment of coated bituminous sludge by combustion/vitrification (report PNGMDR 2013-2015)

International Nuclear Information System (INIS)

2015-01-01

This note reports the assessment of a processing by combustion/vitrification of about 60.000 parcels of coated bituminous sludge belonging to intermediate-level long-lived and low-level long-lived category, and warehoused on the Marcoule CEA site. This assessment identifies the front-end cost of an exploratory R and D which would be required to undo technological locks, the cost of design, realisation and exploitation of the associated installation, and the negative features dues to the lack of technological maturity and to the management of environmental risks and impacts in comparison with the reference industrial solution (geological storage). As a conclusion, the authors state that the process is still not technically feasible

Genome packaging in viruses

OpenAIRE

Sun, Siyang; Rao, Venigalla B.; Rossmann, Michael G.

2010-01-01

Genome packaging is a fundamental process in a viral life cycle. Many viruses assemble preformed capsids into which the genomic material is subsequently packaged. These viruses use a packaging motor protein that is driven by the hydrolysis of ATP to condense the nucleic acids into a confined space. How these motor proteins package viral genomes had been poorly understood until recently, when a few X-ray crystal structures and cryo-electron microscopy structures became available. Here we discu...

Use of additives to improve the capacity of bituminous mixtures to be heated by means of microwaves; Uso de un material volcánico como filler en la producción de hormigones autocompactantes de baja resistencia.

Energy Technology Data Exchange (ETDEWEB)

Gallego, J.; Val, M.A. del; Contreras, V.; Páez, A.

2017-07-01

This study examines the potential of adding electric arc furnace slag to bituminous mixtures to be heated by microwaves. The susceptibility of bituminous mixtures to microwave energy is limited and so, in order to improve the energy performance of the heating process, it is necessary to incorporate additives or components to the mixture so as to improve the capacity for microwave heating. The article presents the results of adding various components, (steel wool, scrap tire wire, silicon carbide, iron filings) and an alternative aggregate: electric arc furnace slag. According to the results obtained in the laboratory, slag addition of at least 5% by weight of the bituminous mixture represents the best option for both technical and economic reasons. The results may promote the valorization of this steel industry residue in bituminous mixtures by improving microwave heating response. [Spanish] El presente trabajo examina el potencial de añadir escorias siderúrgicas de horno de arco eléctrico en mezclas bituminosas cuando se calientan con energía de microondas. La susceptibilidad de las mezclas bituminosas a las microondas es limitada y con el objetivo de incrementarla es necesario incorporar aditivos o componentes que sí son susceptibles. El artículo presenta los resultados obtenidos con varios aditivos (lana de acero, alambre metálico reciclado de neumáticos fuera de uso, carburo de silíceo y limaduras de hierro) y un árido alternativo: escorias de horno de arco eléctrico. De acuerdo con los resultados obtenidos en el estudio, la incorporación de escorias en al menos un 5% en masa de la mezcla bituminosa representa la mejor opción por motivos técnicos y económicos. Este resultado puede potenciar la valorización de este residuo de la industria del acero en mezclas bituminosas para mejorar su respuesta al calentamiento con energía microondas.

Food packaging history and innovations.

Science.gov (United States)

Risch, Sara J

2009-09-23

Food packaging has evolved from simply a container to hold food to something today that can play an active role in food quality. Many packages are still simply containers, but they have properties that have been developed to protect the food. These include barriers to oxygen, moisture, and flavors. Active packaging, or that which plays an active role in food quality, includes some microwave packaging as well as packaging that has absorbers built in to remove oxygen from the atmosphere surrounding the product or to provide antimicrobials to the surface of the food. Packaging has allowed access to many foods year-round that otherwise could not be preserved. It is interesting to note that some packages have actually allowed the creation of new categories in the supermarket. Examples include microwave popcorn and fresh-cut produce, which owe their existence to the unique packaging that has been developed.

Trends in Food Packaging.

Science.gov (United States)

Ott, Dana B.

1988-01-01

This article discusses developments in food packaging, processing, and preservation techniques in terms of packaging materials, technologies, consumer benefits, and current and potential food product applications. Covers implications due to consumer life-style changes, cost-effectiveness of packaging materials, and the ecological impact of…

WASTE PACKAGE TRANSPORTER DESIGN

Energy Technology Data Exchange (ETDEWEB)

D.C. Weddle; R. Novotny; J. Cron

1998-09-23

The purpose of this Design Analysis is to develop preliminary design of the waste package transporter used for waste package (WP) transport and related functions in the subsurface repository. This analysis refines the conceptual design that was started in Phase I of the Viability Assessment. This analysis supports the development of a reliable emplacement concept and a retrieval concept for license application design. The scope of this analysis includes the following activities: (1) Assess features of the transporter design and evaluate alternative design solutions for mechanical components. (2) Develop mechanical equipment details for the transporter. (3) Prepare a preliminary structural evaluation for the transporter. (4) Identify and recommend the equipment design for waste package transport and related functions. (5) Investigate transport equipment interface tolerances. This analysis supports the development of the waste package transporter for the transport, emplacement, and retrieval of packaged radioactive waste forms in the subsurface repository. Once the waste containers are closed and accepted, the packaged radioactive waste forms are termed waste packages (WP). This terminology was finalized as this analysis neared completion; therefore, the term disposal container is used in several references (i.e., the System Description Document (SDD)) (Ref. 5.6). In this analysis and the applicable reference documents, the term ''disposal container'' is synonymous with ''waste package''.

Mobile hot cell transition design phase study for radioactive waste treatment on the Hanford reservation site

International Nuclear Information System (INIS)

Pons, Y.

2010-01-01

Full text of publication follows: At the US Department of Energy's Hanford Reservation site, 4 caissons in under ground storage contain approximately 23 cubic meters of Transuranic (TRU) waste, in over 5,000 small packages. The retrieval of these wastes presents a number of very difficult issues, including the configuration of the vaults, approximately 50,000 curies of activity, high dose rates, and damaged/degraded waste packages. The waste will require remote retrieval and processing sufficient to produce certifiable RH-TRU waste packages. This RH-TRU will be packaged for staging on site until certification by CCP is completed to authorize shipment to the Waste Isolation Pilot Plant (WIPP). The project has introduced AREVA' s innovative Hot Mobile Cell (HMC) technology to perform size reduction, sorting, characterization, and packaging of the RH waste stream at the point of generation, the retrieval site in the field. This approach minimizes dose and hazard exposure to workers that is usually associated with this operation. The HMC can also be used to provide employee protection, weather protection, and capacity improvements similar to those realized in general burial ground. AREVA TA and his partner AFS will provide this technology based on the existing HMCs developed and operated in France: - ERFB (Bituminized Waste Drum Retrieval Facility): ERFB was built specifically for retrieving the bituminized waste drums (approximately 6,000 stored in trenches in the North zone on the Marcoule site (in operation since 2001). - ERCF (Waste Drum Recovery and Packaging Facility): The ERCF was built specifically to retrieve bituminized waste drums stored in 35 pits located in the south area on Marcoule site (in operation) - FOSSEA (Legacy Waste Removal and Trench Cleanup): The FOSSEA project consists of the retrieval of waste stored on the Basic Nuclear Facility. Waste from the 56 trenches will be inspected, characterised, and if necessary processed or repackaged, and

Recycling of polyethylene terephthalate (PET plastic bottle wastes in bituminous asphaltic concrete

Directory of Open Access Journals (Sweden)

Adebayo Olatunbosun Sojobi

2016-12-01

Full Text Available This research sheds light on the concept of eco-friendly road construction which comprises eco-design, eco-extraction, eco-manufacturing, eco-construction, eco-rehabilitation, eco-maintenance, eco-demolition, and socioeconomic empowerment. It also revealed the challenges being faced in its adoption and the benefits derivable from its application. Furthermore, the effects of recycling PET plastic bottle wastes produced in North Central Nigeria in bituminous asphaltic concrete (BAC used in flexible pavement construction were also evaluated. The mix design consists of 60/70 penetration-grade asphaltic concrete (5%, 68% coarse aggregate, 6% fine aggregate, and 21% filler using the dry process at 170°C. The optimum bitumen content (OBC for conventional BAC was obtained as 4% by weight of total aggregates and filler. Polymer-coated aggregate (PCA-modified BAC seems preferable because it has the potential to utilize more plastic wastes with a higher optimum plastic content (OPC of 16.7% by weight of total aggregates and filler compared to that of 9% by weight of OBC achieved by PMB-BAC. For both PMB- and PCA-modified BAC, an increase in air void, void in mineral aggregate, and Marshall stability were observed. Eco-friendly road construction which recycles PET wastes should be encouraged by government considering its potential environmental and economic benefits.

The Innovative Approaches to Packaging – Comparison Analysis of Intelligent and Active Packaging Perceptions in Slovakia

Directory of Open Access Journals (Sweden)

Loucanova Erika

2017-06-01

Full Text Available Packaging has always served a practical function - to hold goods together and protect it when moving toward the customer through distribution channel. Today packaging is also a container for promoting the product and making it easier and safer to use. The sheer importance of packaging functions is still growing and consequently the interest of the company is to access to the packaging more innovative and creative. The paper deals with the innovative approaches to packaging resulting in the creation of packaging with interactive active features in the form of active and intelligent packaging. Using comparative analysis, we monitored the perception of the active packaging functions in comparison to intelligent packaging function among different age categories. We identified the age categories which are most interested in these functions.

Applications of Active Packaging in Breads

Directory of Open Access Journals (Sweden)

Ali Göncü

2017-10-01

Full Text Available Changes on consumer preferences lead to innovations and improvements in new packaging technologies. With these new developments passive packaging technologies aiming to protect food nowadays have left their place to active and intelligent packaging technologies that have other various functions beside protection of food. Active packaging is defined as an innovative packaging type and its usage increases the shelf life of food significantly. Applications of active packaging have begun to be used for packaging of breads. In this study active packaging applications in breads have been reviewed.

Elemental analysis of Indonesian and Australian bituminous coal used at Kapar Power Station

International Nuclear Information System (INIS)

Muneer Saleh; Ahmad Suhaimi

2008-01-01

An instrumental neutron activation analytical (INAA) technique is used for the determination of thirty elements in five coal samples collected from Kapar power station, imported from Indonesia and Australia. Analyses of the samples are being associated with standards. All irradiation were performed in the nuclear reactor of Malaysia Nuclear Agency (MNA). samples were counted by Hyper Pure Germanium (HPGe) detector for short period irradiations at MNA, while for the long period irradiations the samples were counted at Universiti Kebangsaan Malaysia (UKM). The concentrations of thirty elements have been determined: The major components are Cl, Ca, Mg, K, Fe, Ti, and Na with the mean concentrations in the range between 70±69 ppm-6100±1639 ppm; and the trace elements are Zr, V, Mn, Sc, Cr, Co, As, Br, Rb, Sb, Ba, La, Ce, Nd, Sm, Eu, Tb, Yb, Lu, Hf, Th, U and Ta with the mean concentrations in the range between 0.1381±0.0202 - 69.0±2.8 ppm. The results have been compared to the reported data of eight coal samples from the United States and the reported data of Australian bituminous coal. (Author)

Food Packaging Materials

Science.gov (United States)

1978-01-01

The photos show a few of the food products packaged in Alure, a metallized plastic material developed and manufactured by St. Regis Paper Company's Flexible Packaging Division, Dallas, Texas. The material incorporates a metallized film originally developed for space applications. Among the suppliers of the film to St. Regis is King-Seeley Thermos Company, Winchester, Ma'ssachusetts. Initially used by NASA as a signal-bouncing reflective coating for the Echo 1 communications satellite, the film was developed by a company later absorbed by King-Seeley. The metallized film was also used as insulating material for components of a number of other spacecraft. St. Regis developed Alure to meet a multiple packaging material need: good eye appeal, product protection for long periods and the ability to be used successfully on a wide variety of food packaging equipment. When the cost of aluminum foil skyrocketed, packagers sought substitute metallized materials but experiments with a number of them uncovered problems; some were too expensive, some did not adequately protect the product, some were difficult for the machinery to handle. Alure offers a solution. St. Regis created Alure by sandwiching the metallized film between layers of plastics. The resulting laminated metallized material has the superior eye appeal of foil but is less expensive and more easily machined. Alure effectively blocks out light, moisture and oxygen and therefore gives the packaged food long shelf life. A major packaging firm conducted its own tests of the material and confirmed the advantages of machinability and shelf life, adding that it runs faster on machines than materials used in the past and it decreases product waste; the net effect is increased productivity.

Development of new non destructive methods for bituminized radioactive waste drums characterization; Developpement de nouvelles methodes de caracterisation non destructive pour des dechets radioactifs enrobes dans du bitume

Energy Technology Data Exchange (ETDEWEB)

Pin, P

2004-10-15

Radioactive waste constitute a major issue for the nuclear industry. One of the key points is their characterization to optimize their management: treatment and packaging, orientation towards the suited disposal. This thesis proposes an evaluation method of the low-energy photon attenuation, based on the gamma-ray spectra Compton continuum. Effectively, the {sup 241}Am measurement by gamma-ray spectrometry is difficult due to the low energy of its main gamma-ray (59.5 keV). The photon attenuation strongly depends on the bituminous mix composition, which includes very absorbing elements. As the Compton continuum also depends on this absorption, it is possible to link the 59.5 keV line attenuation to the Compton level. Another technique is proposed to characterize uranium thanks to its fluorescence X-rays induced by the gamma emitters already present in the waste. The uranium present in the drums disturbs the neutron measurements and its measurement by self-induced X-ray fluorescence allows to correct this interference. Due to various causes of error, the total uncertainty is around 50 % on the activity of the radioisotope {sup 241}Am, corrected by the peak to Compton technique. The same uncertainty is announced on the uranium mass measured by self induced X-ray fluorescence. As a consequence of these promising results, the two methods were included in the industrial project of the 'Marcoule Sorting Unit'. One major advantage is that they do not imply any additional material because they use information already present in the gamma-ray spectra. (author)

Plasma physics plotting package

International Nuclear Information System (INIS)

Hyman, D.H.

1981-02-01

We describe a package of plotting routines that do up to six two- or three-dimensional plots on a frame with minimal loss of resolution. The package now runs on a PDP-10 with PLOT-10 TCS primitives and on a Control Data Corporation-7600 and a Cray-1 with TV80LIB primitives on the National Magnetic Fusion Energy Computer Center network. The package is portable to other graphics systems because only the primitive plot calls are used from the underlying system's graphics package

Active food packaging technologies.

Science.gov (United States)

Ozdemir, Murat; Floros, John D

2004-01-01

Active packaging technologies offer new opportunities for the food industry, in the preservation of foods. Important active packaging systems currently known to date, including oxygen scavengers, carbon dioxide emitters/absorbers, moisture absorbers, ethylene absorbers, ethanol emitters, flavor releasing/absorbing systems, time-temperature indicators, and antimicrobial containing films, are reviewed. The principle of operation of each active system is briefly explained. Recent technological advances in active packaging are discussed, and food related applications are presented. The effects of active packaging systems on food quality and safety are cited.

Naval Waste Package Design Report

International Nuclear Information System (INIS)

M.M. Lewis

2004-01-01

A design methodology for the waste packages and ancillary components, viz., the emplacement pallets and drip shields, has been developed to provide designs that satisfy the safety and operational requirements of the Yucca Mountain Project. This methodology is described in the ''Waste Package Design Methodology Report'' Mecham 2004 [DIRS 166168]. To demonstrate the practicability of this design methodology, four waste package design configurations have been selected to illustrate the application of the methodology. These four design configurations are the 21-pressurized water reactor (PWR) Absorber Plate waste package, the 44-boiling water reactor (BWR) waste package, the 5-defense high-level waste (DHLW)/United States (U.S.) Department of Energy (DOE) spent nuclear fuel (SNF) Co-disposal Short waste package, and the Naval Canistered SNF Long waste package. Also included in this demonstration is the emplacement pallet and continuous drip shield. The purpose of this report is to document how that design methodology has been applied to the waste package design configurations intended to accommodate naval canistered SNF. This demonstrates that the design methodology can be applied successfully to this waste package design configuration and support the License Application for construction of the repository

49 CFR 173.24 - General requirements for packagings and packages.

Science.gov (United States)

2010-10-01

... identifiable (without the use of instruments) release of hazardous materials to the environment; (2) The effectiveness of the package will not be substantially reduced; for example, impact resistance, strength... significant chemical or galvanic reaction between the materials and contents of the package. (3) Plastic...

Packaging systems for animal origin food

Directory of Open Access Journals (Sweden)

2011-03-01

Full Text Available The main task of food packaging is to protect the product during storage and transport against the action of biological, chemical and mechanical factors. The paper presents packaging systems for food of animal origin. Vacuum and modified atmosphere packagings were characterised together with novel types of packagings, referred to as intelligent packaging and active packaging. The aim of this paper was to present all advantages and disadvantages of packaging used for meat products. Such list enables to choose the optimal type of packaging for given assortment of food and specific conditions of the transport and storing.

Merganser Download Package

Data.gov (United States)

U.S. Environmental Protection Agency — This data download package contains an Esri 10.0 MXD, file geodatabase and copy of this FGDC metadata record. The data in this package are used in support of the...

Modular assembly of chimeric phi29 packaging RNAs that support DNA packaging.

Science.gov (United States)

Fang, Yun; Shu, Dan; Xiao, Feng; Guo, Peixuan; Qin, Peter Z

2008-08-08

The bacteriophage phi29 DNA packaging motor is a protein/RNA complex that can produce strong force to condense the linear-double-stranded DNA genome into a pre-formed protein capsid. The RNA component, called the packaging RNA (pRNA), utilizes magnesium-dependent inter-molecular base-pairing interactions to form ring-shaped complexes. The pRNA is a class of non-coding RNA, interacting with phi29 motor proteins to enable DNA packaging. Here, we report a two-piece chimeric pRNA construct that is fully competent in interacting with partner pRNA to form ring-shaped complexes, in packaging DNA via the motor, and in assembling infectious phi29 virions in vitro. This is the first example of a fully functional pRNA assembled using two non-covalently interacting fragments. The results support the notion of modular pRNA architecture in the phi29 packaging motor.

The art of packaging: An investigation into the role of color in packaging, marketing, and branding

Directory of Open Access Journals (Sweden)

Behzad Mohebbi

2014-12-01

Full Text Available The purpose of this study is to contribute to the existing research in the field of packaging and marketing and shed more light on the psychology of colors and their effect on packaging and marketing. Nowadays, packaging is proved to be one of the significant factors in the success of promoting product sale. However, there is a perceived gap with respect to the different aspects of packaging, in particular the graphics, design, and color of packaging. The current study provides a comprehensive overview of packaging. It elaborates on different aspects of packaging and summarizes the findings of the most recent research conducted to date probing into packaging from different perspectives. It also discusses the role of color, i.e., the psychology of colors, and graphics in packaging and product sale. It is argued that graphics and color play key roles in promoting product sale and designers and marketers should attach a great deal of importance to color in packaging. The implications for producers, marketers, practitioners, and researchers are discussed in detail and suggestions for future research are provided.

Thermodynamic analysis and economic evaluation of a 1000 MW bituminous coal fired power plant incorporating low-temperature pre-drying (LTPD)

International Nuclear Information System (INIS)

Xu, Cheng; Xu, Gang; Zhu, Mingming; Dong, Wei; Zhang, Yang; Yang, Yongping; Zhang, Dongke

2016-01-01

Highlights: • An improved design of coal pre-drying using flue gas waste heat was proposed. • 0.4% energy efficiency increase was achieved with the proposed system. • The additional net economic benefit of the proposed system is $1.91 M per year. • Proposed concept can be widely applied to improve coal-fired power plant efficiency. - Abstract: Low-temperature pre-drying (LTPD) of lignite has been identified as an effective approach to improve the efficiency of lignite fired power plants. In this study, an improved concept for the pre-drying of medium moisture bituminous coals using flue gas waste heat was proposed and its feasibility was assessed. In the proposed configuration, the boiler exhaust flue gas is drawn to dryers to heat and pre-dry the raw coal, removing a large proportion of the coal moisture and leading to an improvement in the energy efficiency of the power plant. Thermodynamic analysis and economic evaluation were performed based on a typical 1000 MW bituminous coal fired power plant incorporating the proposed LTPD concept. The results showed that the net power plant efficiency gain is as much as 0.4 percentage point with additional net power output of 9.3 MW as compared to the reference plant without coal pre-drying. This was attributed to the reduction in the moisture content from 10.3 to 2.7 wt%. The additional net economic benefit attained due to the coal pre-drying was estimated to reach $1.91 M per year. This work provides a broadly applicable and economically feasible approach to further improve the energy efficiency of power plants firing coals with medium moisture contents.

MINUIT package parallelization and applications using the RooFit package

International Nuclear Information System (INIS)

Lazzaro, Alfio; Moneta, Lorenzo

2010-01-01

The fitting procedures are based on numerical minimization of functions. The MINUIT package is the most common package used for such procedures in High Energy Physics community. The main algorithm in this package, MIGRAD, searches the minimum of a function using the gradient information. For each minimization iteration, MIGRAD requires the calculation of the derivative for each free parameter of the function to be minimized. Minimization is required for data analysis problems based on the maximum likelihood technique. The calculation of complex likelihood functions, with several free parameters, many independent variables and large data samples, can be very CPU-time consuming. Then, the minimization process requires the calculation of the likelihood functions several times for each minimization iteration. In this paper we will show how MIGRAD algorithm and the likelihood function calculation can be easily parallelized using Message Passing Interface techniques. We will present the speed-up improvements obtained in typical physics applications such as complex maximum likelihood fits using the RooFit package.

Waste package performance analysis

International Nuclear Information System (INIS)

Lester, D.H.; Stula, R.T.; Kirstein, B.E.

1982-01-01

A performance assessment model for multiple barrier packages containing unreprocessed spent fuel has been applied to several package designs. The resulting preliminary assessments were intended for use in making decisions about package development programs. A computer model called BARIER estimates the package life and subsequent rate of release of selected nuclides. The model accounts for temperature, pressure (and resulting stresses), bulk and localized corrosion, and nuclide retardation by the backfill after water intrusion into the waste form. The assessment model assumes a post-closure, flooded, geologic repository. Calculations indicated that, within the bounds of model assumptions, packages could last for several hundred years. Intact backfills of appropriate design may be capable of nuclide release delay times on the order of 10 7 yr for uranium, plutonium, and americium. 8 references, 6 figures, 9 tables

Comparative Packaging Study

Science.gov (United States)

Perchonok, Michele H.; Oziomek, Thomas V.

2009-01-01

Future long duration manned space flights beyond low earth orbit will require the food system to remain safe, acceptable and nutritious. Development of high barrier food packaging will enable this requirement by preventing the ingress and egress of gases and moisture. New high barrier food packaging materials have been identified through a trade study. Practical application of this packaging material within a shelf life test will allow for better determination of whether this material will allow the food system to meet given requirements after the package has undergone processing. The reason to conduct shelf life testing, using a variety of packaging materials, stems from the need to preserve food used for mission durations of several years. Chemical reactions that take place during longer durations may decrease food quality to a point where crew physical or psychological well-being is compromised. This can result in a reduction or loss of mission success. The rate of chemical reactions, including oxidative rancidity and staling, can be controlled by limiting the reactants, reducing the amount of energy available to drive the reaction, and minimizing the amount of water available. Water not only acts as a media for microbial growth, but also as a reactant and means by which two reactants may come into contact with each other. The objective of this study is to evaluate three packaging materials for potential use in long duration space exploration missions.

Intelligent food packaging - research and development

Directory of Open Access Journals (Sweden)

Renata Dobrucka

2015-03-01

Full Text Available Packaging also fosters effective marketing of the food through distribution and sale channels. It is of the utmost importance to optimize the protection of the food, a great quality and appearance - better than typical packaged foods. In recent years, intelligent packaging became very popular. Intelligent packaging is becoming more and more widely used for food products. Application of this type of solution contributes to improvement of the quality consumer life undoubtedly. Intelligent packaging refers to a package that can sense environmental changes, and in turn, informs the users about the changes. These packaging systems contain devices that are capable of sensing and providing information about the functions and properties of the packaged foods. Also, this paper will review intelligent packaging technologies and describe different types of indicators (time-temperature indicators, freshness indicators.

Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas

Energy Technology Data Exchange (ETDEWEB)

Carl Richardson; Katherine Dombrowski; Douglas Orr

2006-12-31

This project Final Report is submitted to the U.S. Department of Energy (DOE) as part of Cooperative Agreement DE-FC26-03NT41987, 'Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas.' Sorbent injection technology is targeted as the primary mercury control process on plants burning low/medium sulfur bituminous coals equipped with ESP and ESP/FGD systems. About 70% of the ESPs used in the utility industry have SCAs less than 300 ft2/1000 acfm. Prior to this test program, previous sorbent injection tests had focused on large-SCA ESPs. This DOE-NETL program was designed to generate data to evaluate the performance and economic feasibility of sorbent injection for mercury control at power plants that fire bituminous coal and are configured with small-sized electrostatic precipitators and/or an ESP-flue gas desulfurization (FGD) configuration. EPRI and Southern Company were co-funders for the test program. Southern Company and Reliant Energy provided host sites for testing and technical input to the project. URS Group was the prime contractor to NETL. ADA-ES and Apogee Scientific Inc. were sub-contractors to URS and was responsible for all aspects of the sorbent injection systems design, installation and operation at the different host sites. Full-scale sorbent injection for mercury control was evaluated at three sites: Georgia Power's Plant Yates Units 1 and 2 [Georgia Power is a subsidiary of the Southern Company] and Reliant Energy's Shawville Unit 3. Georgia Power's Plant Yates Unit 1 has an existing small-SCA cold-side ESP followed by a Chiyoda CT-121 wet scrubber. Yates Unit 2 is also equipped with a small-SCA ESP and a dual flue gas conditioning system. Unit 2 has no SO2 control system. Shawville Unit 3 is equipped with two small-SCA cold-side ESPs operated in series. All ESP systems tested in this program had SCAs less than 250 ft2/1000 acfm. Short-term parametric tests were conducted on Yates

Creative Thinking Package

Science.gov (United States)

Jones, Clive

1972-01-01

A look at the latest package from a British managment training organization, which explains and demonstrates creative thinking techniques, including brainstorming. The package, designed for groups of twelve or more, consists of tapes, visuals, and associated exercises. (Editor/JB)

Perspectives on the Elements of Packaging Design : A Qualitative Study on the Communication of Packaging

OpenAIRE

Alervall, Viktoria; Saied, Juan Sdiq

2013-01-01

Background: In today’s markets almost all products we buy come packaged. We use packaging to protect, contain and identify products. Furthermore if this is executed in a skillful way consumers often choose products based on packaging. The work of a designer and marketer is therefore extremely valuable when it comes to the design of a package. Problem: How are packages used to communicate marketing information? Purpose: The focus of this thesis is to identify differences and similarities of a ...

21 CFR 355.20 - Packaging conditions.

Science.gov (United States)

2010-04-01

... conditions. (a) Package size limitation. Due to the toxicity associated with fluoride active ingredients, the... (toothpastes and tooth powders) packages shall not contain more than 276 milligrams (mg) total fluorine per... packages shall not contain more than 120 mg total fluorine per package. (3) Exception. Package size...

19 CFR 191.13 - Packaging materials.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Packaging materials. 191.13 Section 191.13 Customs... (CONTINUED) DRAWBACK General Provisions § 191.13 Packaging materials. (a) Imported packaging material... packaging material when used to package or repackage merchandise or articles exported or destroyed pursuant...

Warpage of QFN Package in Post Mold Cure Process of integrated circuit packaging

Science.gov (United States)

Sriwithoon, Nattha; Ugsornrat, Kessararat; Srisuwitthanon, Warayoot; Thonglor, Panakamon

2017-09-01

This research studied about warpage of QFN package in post mold cure process of integrated circuit (IC) packages using pre-plated (PPF) leadframe. For IC package, epoxy molding compound (EMC) are molded by cross linking of compound stiffness but incomplete crosslinked network and leading the fully cured thermoset by post mold cure (PMC) process. The cure temperature of PMC can change microstructure of EMC in term of stress inside the package and effect to warpage of the package due to coefficient of thermal expansion (CTE) between EMC and leadframe. In experiment, cure temperatures were varied to check the effect of internal stress due to different cure temperature after completed post mold cure for TDFN 2×3 8L. The cure temperature were varied with 180 °C, 170 °C, 160 °C, and 150°C with cure time 4 and 6 hours, respectively. For analysis, the TDFN 2×3 8L packages were analyzed the warpage by thickness gauge and scanning acoustic microscope (SAM) after take the test samples out from the oven cure. The results confirmed that effect of different CTE between EMC and leadframe due to different cure temperature resulting to warpage of the TDFN 2×3 8L packages.

CYPROS - Cybernetic Program Packages

Directory of Open Access Journals (Sweden)

Arne Tyssø

1980-10-01

Full Text Available CYPROS is an interactive program system consisting of a number of special purpose packages for simulation, identification, parameter estimation and control system design. The programming language is standard FORTRAN IV and the system is implemented on a medium size computer system (Nord-10. The system is interactive and program control is obtained by the use of numeric terminals. Output is rapidly examined by extensive use of video colour graphics. The subroutines included in the packages are designed and documented according to standardization rules given by the SCL (Scandinavian Control Library organization. This simplifies the exchange of subroutines throughout the SCL system. Also, this makes the packages attractive for implementation by industrial users. In the simulation package, different integration methods are available and it can be easily used for off-line, as well as real time, simulation problems. The identification package consists of programs for single-input/single-output and multivariablc problems. Both transfer function models and state space models can be handled. Optimal test signals can be designed. The control package consists of programs based on multivariable time domain and frequency domain methods for analysis and design. In addition, there is a package for matrix and time series manipulation. CYPROS has been applied successfully to industrial problems of various kinds, and parts of the system have already been implemented on different computers in industry. This paper will, in some detail, describe the use and the contents of the packages and some examples of application will be discussed.

Characterization of integrated circuit packaging materials

CERN Document Server

Moore, Thomas

1993-01-01

Chapters in this volume address important characteristics of IC packages. Analytical techniques appropriate for IC package characterization are demonstrated through examples of the measurement of critical performance parameters and the analysis of key technological problems of IC packages. Issues are discussed which affect a variety of package types, including plastic surface-mount packages, hermetic packages, and advanced designs such as flip-chip, chip-on-board and multi-chip models.

The ZOOM minimization package

International Nuclear Information System (INIS)

Fischler, Mark S.; Sachs, D.

2004-01-01

A new object-oriented Minimization package is available for distribution in the same manner as CLHEP. This package, designed for use in HEP applications, has all the capabilities of Minuit, but is a re-write from scratch, adhering to modern C++ design principles. A primary goal of this package is extensibility in several directions, so that its capabilities can be kept fresh with as little maintenance effort as possible. This package is distinguished by the priority that was assigned to C++ design issues, and the focus on producing an extensible system that will resist becoming obsolete

Packaging Concerns/Techniques for Large Devices

Science.gov (United States)

Sampson, Michael J.

2009-01-01

This slide presentation reviews packaging challenges and options for electronic parts. The presentation includes information about non-hermetic packages, space challenges for packaging and complex package variations.

Nitrogen-enriched bituminous coal-based active carbons as materials for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

R. Pietrzak; K. Jurewicz; P. Nowicki; K. Babel; H. Wachowska [A. Mickiewicz University, Poznan (Poland). Laboratory of Coal Chemistry and Technology

2010-11-15

The paper presents the results of a study on obtaining N-enriched active carbons from bituminous coal and on testing its use as an electrode material in supercapacitors. The coal was carbonised, activated with KOH and ammoxidised by a mixture of ammonia and air at the ratio 1:3 at 300{sup o}C or 350{sup o}C, at different stages of the production, that is, at those of precursor, carbonisate, and active carbon. The products were microporous N-enriched active carbon samples of well-developed surface area reaching from 1577 to 2510 m{sup 2}/g and containing 1.0 to 8.5 wt% of nitrogen. The XPS measurements have shown that in the active carbons enriched in nitrogen at the stage of precursor and at the stage of carbonisate, the dominant nitrogen species are the N-5 groups, while in the samples ammoxidised at the last stage of the treatment the dominant nitrogen species are the surface groups of imines and/or nitriles, probably accompanied by amines and amides. The paper reports the results of a comprehensive study of the effect of the structure and chemical composition of a series of active carbon samples of different properties on their capacity performance in water solutions of H{sub 2}SO{sub 4} or KOH, with the behaviour of positive and negative electrodes analysed separately. 33 refs., 7 figs., 8 tabs.

Packaging and transport of radioisotopes

International Nuclear Information System (INIS)

Taylor, C.B.G.

1976-01-01

The importance of radioisotope traffic is emphasized. More than a million packages are being transported each year, mostly for medical uses. The involvement of public transport services and the incidental dose to the public (which is very small) are appreciably greater than for movements connected with the nuclear fuel cycle. Modern isotope packages are described, and an outline given of the problems of a large radioisotope manufacturer who has to package many different types of product. Difficulties caused by recent uncoordinated restrictions on the use of passenger aircraft are mentioned. Some specific problems relating to radioisotope packaging are discussed. These include the crush resistance of Type A packages, the closure of steel drums, the design of secure closures for large containers, the Type A packaging of liquids, leak tightness criteria of Type B packages, and the use of 'unit load' overpacks to consign a group of individually approved packages together as a single shipment. Reference is made to recent studies of the impact of radioisotope shipments on the environment. Cost/benefit analysis is important in this field - an important public debate is only just beginning. (author)

Safety Analysis Report - Packages, 9965, 9968, 9972-9975 Packages

International Nuclear Information System (INIS)

Van Alstine, M.N.

1999-01-01

This Safety Analysis Report for Packaging (SARP) documents the performance of the 9965 B, 9968 B, 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages in satisfying the regulatory safety requirements of the Code of Federal Regulations (CFR) 711 and the International Atomic Energy Agency (IAEA) Safety Series No. 6, Regulations for the Safe Transport of Radioactive Material, 1985 edition2. Results of the analysis and testing performed on the 9965 B, 9968 B, 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages are presented in this SARP, which was prepared in accordance with U.S. Department of energy (DOE) Order 5480.33 and in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guides 7.94 and 7.10.5

Safety analysis report - packages 9965, 9968, 9972-9975 packages

International Nuclear Information System (INIS)

Van Alstine, M.N.

1997-10-01

This Safety Analysis Report for Packaging (SARP) documents the performance of the 9965 B( ), 9968 B( ), 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages in satisfying the regulatory safety requirements of the Code of Federal Regulations (CFR) 10 CFR 71 and the International Atomic Energy Agency (IAEA) Safety Series No. 6, Regulations for the Safe Transport of Radioactive Material, 1985 edition. Results of the analysis and testing performed on the 9965 B(), 9968 B(), 9972 B(U), 9973 B(U), and 9975 B(U) packages are presented in this SARP, which was prepared in accordance with U.S. Department of Energy (DOE) Order 5480.3 and in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guides 7.9 and 7.10

Healthy package, healthy product? Effects of packaging design as a function of purchase setting

NARCIS (Netherlands)

van Rompay, Thomas Johannes Lucas; Deterink, Florien; Fenko, Anna

2016-01-01

Inspired by research testifying to the influence of visual packaging appearance and meaning portrayal on food evaluation, here it is argued that effects of packaging design vary depending on purchase context. Realistic packaging variants for a fictitious yoghurt brand varying in health connotation

Integrated Approach to Industrial Packaging Design

Science.gov (United States)

Vorobeva, O.

2017-11-01

The article reviews studies in the field of industrial packaging design. The major factors which influence technological, ergonomic, economic and ecological features of packaging are established. The main modern trends in packaging design are defined, the principles of marketing communications and their influence on consumers’ consciousness are indicated, and the function of packaging as a transmitter of brand values is specified. Peculiarities of packaging technology and printing techniques in modern printing industry are considered. The role of designers in the stage-by-stage development of the construction, form and graphic design concept of packaging is defined. The examples of authentic packaging are given and the mention of the tetrahedron packaging history is made. At the end of the article, conclusions on the key research aspects are made.

Directory of certificates of compliance for radioactive materials packages. Summary report of NRC approved packages

International Nuclear Information System (INIS)

1979-10-01

This directory contains a Summary Report of NRC Approved Packages for radioactive material packages effective September 14, 1979. Purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance number is included at the back of each volume of the directory. The Summary Report includes a listing of all users of each package design prior to the publication date of the directory

Directory of certificates of compliance for radioactive materials packages. Summary report of NRC approved packages

Energy Technology Data Exchange (ETDEWEB)

None

1979-10-01

This directory contains a Summary Report of NRC Approved Packages for radioactive material packages effective September 14, 1979. Purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance number is included at the back of each volume of the directory. The Summary Report includes a listing of all users of each package design prior to the publication date of the directory.

Directory of Certificates of Compliance for Radioactive Materials Packages: Report of NRC approved packages

International Nuclear Information System (INIS)

1988-12-01

This directory contains a Report of the US Nuclear Regulatory Commission's Approved Packages (Volume 1), all Certificates of Compliance (Volume 2), and a Report of NRC Approved Quality Assurance Programs (Volume 3) for Radioactive Material Packages effective October 1, 1988. The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the front of Volume 2 of the directory. A listing by packaging types is included in the back of Volume 2. An alphabetical listing by Company name is included in the back of Volume 3 for approved QA programs. The Reports include a listing of all users of each package design and approved QA programs prior to the publication date of the directory

Directory of certificates of compliance for radioactive materials packages, Report of NRC approved packages

International Nuclear Information System (INIS)

1990-10-01

This directory contains a Report of the US Nuclear Regulatory Commission's Approved Packages (Volume 1), Certificates of Compliance (Volume 2), and a Report of NRC Approved Quality Assurance Programs (Volume 3) for Radioactive Materials Packages effective October 1, 1990. The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the front of Volume 2 of the directory. A listing by packaging types is included in the back of Volume 2. An alphabetical listing by Company name is included in the back of Volume 3 for approved QA programs. The Reports include a listing of all users of each package design and approved QA programs prior to the publication date of the directory

Safety analysis report for packages: packaging of fissile and other radioactive materials. Final report

International Nuclear Information System (INIS)

Chalfant, G.G.

1984-01-01

The 9965, 9966, 9967, and 9968 packages are designed for surface shipment of fissile and other radioactive materials where a high degree of containment (either single or double) is required. Provisions are made to add shielding material to the packaging as required. The package was physically tested to demonstrate that it meets the criteria specified in USDOE Order No. 5480.1, chapter III, dated 5/1/81, which invokes Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packing and Transportation of Radioactive Material, and Title 49, Code of Federal Regulations, Part 100-179, Transportation. By restricting the maximum normal operating pressure of the packages to less than 7 kg/cm 2 (gauge) (99 to 54 psig), the packages will comply with Type B(U) regulations of the International Atomic Energy Agency (IAEA) in its Regulations for the Safe Transport of Radioactive Materials, Safety Series No. 6, 1973 Revised Edition, and may be used for export and import shipments. These packages have been assessed for transport of up to 14.5 kilograms of uranium, excluding uranium-233, or 4.4 kilograms of plutonium metal, oxides, or scrap having a maximum radioactive decay energy of 30 watts. Specific maximum package contents are given. This quantity and the configuration of uranium or plutonium metal cannot be made critical by any combination of hydrogeneous reflection and moderation regardless of the condition of the package. For a uranium-233 shipment, a separate criticality evaluation for the specific package is required

Ensuring socially responsible packaging design

DEFF Research Database (Denmark)

Geert Jensen, Birgitte

Most consumers have experienced occasional problems with opening packaging. Tomato sauce from the tinned mackerel splattered all over the kitchen counter, the unrelenting pickle jar lid, and the package of sliced ham that cannot be opened without a knife or a pair of scissors. The research project...... "User‐friendly Packaging" aims to create a platform for developing more user‐friendly packaging. One intended outcome of the project is a guideline that industry can use in development efforts. The project also points the way for more extended collaboration between companies and design researchers. How...... can design research help industry in packaging innovation?...

Packaging based on polymeric materials

Directory of Open Access Journals (Sweden)

Jovanović Slobodan M.

2005-01-01

Full Text Available In the past two years the consumption of common in the developed countries world wide (high tonnage polymers for packaging has approached a value of 50 wt.%. In the same period more than 50% of the packaging units on the world market were made of polymeric materials despite the fact that polymeric materials present 17 wt.% of all packaging materials. The basic properties of polymeric materials and their environmental and economical advantages, providing them such a position among packaging materials, are presented in this article. Recycling methods, as well as the development trends of polymeric packaging materials are also presented.

Advanced flip chip packaging

CERN Document Server

Lai, Yi-Shao; Wong, CP

2013-01-01

Advanced Flip Chip Packaging presents past, present and future advances and trends in areas such as substrate technology, material development, and assembly processes. Flip chip packaging is now in widespread use in computing, communications, consumer and automotive electronics, and the demand for flip chip technology is continuing to grow in order to meet the need for products that offer better performance, are smaller, and are environmentally sustainable. This book also: Offers broad-ranging chapters with a focus on IC-package-system integration Provides viewpoints from leading industry executives and experts Details state-of-the-art achievements in process technologies and scientific research Presents a clear development history and touches on trends in the industry while also discussing up-to-date technology information Advanced Flip Chip Packaging is an ideal book for engineers, researchers, and graduate students interested in the field of flip chip packaging.

Challenges in the Packaging of MEMS

Energy Technology Data Exchange (ETDEWEB)

Malshe, A.P.; Singh, S.B.; Eaton, W.P.; O' Neal, C.; Brown, W.D.; Miller, W.M.

1999-03-26

The packaging of Micro-Electro-Mechanical Systems (MEMS) is a field of great importance to anyone using or manufacturing sensors, consumer products, or military applications. Currently much work has been done in the design and fabrication of MEMS devices but insufficient research and few publications have been completed on the packaging of these devices. This is despite the fact that packaging is a very large percentage of the total cost of MEMS devices. The main difference between IC packaging and MEMS packaging is that MEMS packaging is almost always application specific and greatly affected by its environment and packaging techniques such as die handling, die attach processes, and lid sealing. Many of these aspects are directly related to the materials used in the packaging processes. MEMS devices that are functional in wafer form can be rendered inoperable after packaging. MEMS dies must be handled only from the chip sides so features on the top surface are not damaged. This eliminates most current die pick-and-place fixtures. Die attach materials are key to MEMS packaging. Using hard die attach solders can create high stresses in the MEMS devices, which can affect their operation greatly. Low-stress epoxies can be high-outgassing, which can also affect device performance. Also, a low modulus die attach can allow the die to move during ultrasonic wirebonding resulting to low wirebond strength. Another source of residual stress is the lid sealing process. Most MEMS based sensors and devices require a hermetically sealed package. This can be done by parallel seam welding the package lid, but at the cost of further induced stress on the die. Another issue of MEMS packaging is the media compatibility of the packaged device. MEMS unlike ICS often interface with their environment, which could be high pressure or corrosive. The main conclusion we can draw about MEMS packaging is that the package affects the performance and reliability of the MEMS devices. There is a

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant| (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations(CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2007-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

User friendly packaging

DEFF Research Database (Denmark)

Geert Jensen, Birgitte

2010-01-01

Most consumers have experienced occasional problems with opening packaging. Tomato sauce from the tinned mackerel splattered all over the kitchen counter, the unrelenting pickle jar lid, and the package of sliced ham that cannot be opened without a knife or a pair of scissors. The research project...

Packaging of control system software

International Nuclear Information System (INIS)

Zagar, K.; Kobal, M.; Saje, N.; Zagar, A.; Sabjan, R.; Di Maio, F.; Stepanov, D.

2012-01-01

Control system software consists of several parts - the core of the control system, drivers for integration of devices, configuration for user interfaces, alarm system, etc. Once the software is developed and configured, it must be installed to computers where it runs. Usually, it is installed on an operating system whose services it needs, and also in some cases dynamically links with the libraries it provides. Operating system can be quite complex itself - for example, a typical Linux distribution consists of several thousand packages. To manage this complexity, we have decided to rely on Red Hat Package Management system (RPM) to package control system software, and also ensure it is properly installed (i.e., that dependencies are also installed, and that scripts are run after installation if any additional actions need to be performed). As dozens of RPM packages need to be prepared, we are reducing the amount of effort and improving consistency between packages through a Maven-based infrastructure that assists in packaging (e.g., automated generation of RPM SPEC files, including automated identification of dependencies). So far, we have used it to package EPICS, Control System Studio (CSS) and several device drivers. We perform extensive testing on Red Hat Enterprise Linux 5.5, but we have also verified that packaging works on CentOS and Scientific Linux. In this article, we describe in greater detail the systematic system of packaging we are using, and its particular application for the ITER CODAC Core System. (authors)

Sensory impacts of food-packaging interactions.

Science.gov (United States)

Duncan, Susan E; Webster, Janet B

2009-01-01

Sensory changes in food products result from intentional or unintentional interactions with packaging materials and from failure of materials to protect product integrity or quality. Resolving sensory issues related to plastic food packaging involves knowledge provided by sensory scientists, materials scientists, packaging manufacturers, food processors, and consumers. Effective communication among scientists and engineers from different disciplines and industries can help scientists understand package-product interactions. Very limited published literature describes sensory perceptions associated with food-package interactions. This article discusses sensory impacts, with emphasis on oxidation reactions, associated with the interaction of food and materials, including taints, scalping, changes in food quality as a function of packaging, and examples of material innovations for smart packaging that can improve sensory quality of foods and beverages. Sensory evaluation is an important tool for improved package selection and development of new materials.

Plutonium stabilization and packaging system

International Nuclear Information System (INIS)

1996-01-01

This document describes the functional design of the Plutonium Stabilization and Packaging System (Pu SPS). The objective of this system is to stabilize and package plutonium metals and oxides of greater than 50% wt, as well as other selected isotopes, in accordance with the requirements of the DOE standard for safe storage of these materials for 50 years. This system will support completion of stabilization and packaging campaigns of the inventory at a number of affected sites before the year 2002. The package will be standard for all sites and will provide a minimum of two uncontaminated, organics free confinement barriers for the packaged material

RH Packaging Operations Manual

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2003-01-01

This procedure provides operating instructions for the RH-TRU 72-B Road Cask, Waste Shipping Package. In this document, ''Packaging'' refers to the assembly of components necessary to ensure compliance with the packaging requirements (not loaded with a payload). ''Package'' refers to a Type B packaging that, with its radioactive contents, is designed to retain the integrity of its containment and shielding when subject to the normal conditions of transport and hypothetical accident test conditions set forth in 10 CFR Part 71. Loading of the RH 72-B cask can be done two ways, on the RH cask trailer in the vertical position or by removing the cask from the trailer and loading it in a facility designed for remote-handling (RH). Before loading the 72-B cask, loading procedures and changes to the loading procedures for the 72-B cask must be sent to CBFO at sitedocuments at wipp.ws for approval

Report on the coal liquefaction committee in fiscal 1992; 1992 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the coal liquefaction committee in fiscal 1992. The first committee meeting was held on August 21. After having confirmed the minutes of the previous meeting, an explanation was given on the research and development plans in fiscal 1992. The explanation covered the general explanation, bituminous coal liquefaction, brown coal liquefaction, and the common and fundamental aspects. The presented topics included the achievements in the operations using a bituminous coal liquefaction PSU and a small device, the status of compiling the achievements in the brown coal liquefaction project, preparation of the basic policy on developing the common basic technologies, and structuring of a coal liquefaction technology package. The second meeting was held on March 18, 1993. The meeting verified the minutes of the previous meeting, and gave the sub-committee reports for fiscal 1992. The sub-committees include those for bituminous coal liquefaction, brown coal liquefaction, environmental safety evaluation, and separation and refining technologies. As the summary of the achievements in fiscal 1992, descriptions were given on the bituminous coal liquefaction, brown coal liquefaction, and common and basic aspects. The fiscal 1993 plan presented included the budget aspect. A description was given as a topic on the economic performance evaluation and the working scheme (the execution plan) for the brown coal liquefaction process. (NEDO)

MARS software package status

International Nuclear Information System (INIS)

Azhgirej, I.L.; Talanov, V.V.

2000-01-01

The MARS software package is intended for simulating the nuclear-electromagnetic cascades and the secondary neutrons and muons transport in the heterogeneous medium of arbitrary complexity in the magnetic fields presence. The inclusive approach to describing the particle production in the nuclear and electromagnetic interactions and by the unstable particles decay is realized in the package. The MARS software package was actively applied for solving various radiation physical problems [ru

CH Packaging Program Guidance

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2003-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP charges the WIPP management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document provides the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs

CH Packaging Program Guidance

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2002-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT Shipping Package, and directly related components. This document complies with the minimum requirements as specified in TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event there is a conflict between this document and the SARP or C of C, the SARP and/or C of C shall govern. C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SAR P charges the WIPP Management and Operation (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document details the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize these operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs

Consumer response to packaging design

NARCIS (Netherlands)

Steenis, Nigel D.; Herpen, van Erica; Lans, van der Ivo A.; Ligthart, Tom N.; Trijp, van Hans C.M.

2017-01-01

Building on theories of cue utilization, this paper investigates whether and how packaging sustainability influences consumer perceptions, inferences and attitudes towards packaged products. A framework is tested in an empirical study among 249 students using soup products varying in packaging

Natural biopolimers in organic food packaging

Science.gov (United States)

Wieczynska, Justyna; Cavoski, Ivana; Chami, Ziad Al; Mondelli, Donato; Di Donato, Paola; Di Terlizzi, Biagio

2014-05-01

Concerns on environmental and waste problems caused by use of non-biodegradable and non-renewable based plastic packaging have caused an increase interest in developing biodegradable packaging using renewable natural biopolymers. Recently, different types of biopolymers like starch, cellulose, chitosan, casein, whey protein, collagen, egg white, soybean protein, corn zein, gelatin and wheat gluten have attracted considerable attention as potential food packaging materials. Recyclable or biodegradable packaging material in organic processing standards is preferable where possible but specific principles of packaging are not precisely defined and standards have to be assessed. There is evidence that consumers of organic products have specific expectations not only with respect to quality characteristics of processed food but also in social and environmental aspects of food production. Growing consumer sophistication is leading to a proliferation in food eco-label like carbon footprint. Biopolymers based packaging for organic products can help to create a green industry. Moreover, biopolymers can be appropriate materials for the development of an active surfaces designed to deliver incorporated natural antimicrobials into environment surrounding packaged food. Active packaging is an innovative mode of packaging in which the product and the environment interact to prolong shelf life or enhance safety or sensory properties, while maintaining the quality of the product. The work will discuss the various techniques that have been used for development of an active antimicrobial biodegradable packaging materials focusing on a recent findings in research studies. With the current focus on exploring a new generation of biopolymer-based food packaging materials with possible applications in organic food packaging. Keywords: organic food, active packaging, biopolymers , green technology

Poverty, inequality and violence in urban India: Towards more ...

International Development Research Centre (IDRC) Digital Library (Canada)

Extrants. Dossiers. Women's safety and transport [Assamese version]. Dossiers. Towards an inclusive and safe Delhi : policy brief. Dossiers. Bombay Hotel : gender insecurity and violence against women. Dossiers. Bombay Hotel : crime, violence and unsafe spaces in informal commercial subdivisions ...

Mathematical simulation of gas pressure in fibre-reinforced concrete container at radiation and biological decomposition of cellulose, bituminized and concrete radwastes

International Nuclear Information System (INIS)

Kuruc, J.; Kvito, P.

2005-01-01

Fibre-reinforced concrete container (FRCC) are used for long-time repository of radioactive wastes. Low- and middle-active radwastes from operation of the NPPs V-1, V-2 Jaslovske Bohunice, Mochovce NPP and from decommissioned NPP A-1 (Jaslovske Bohunice) are treated in the plant SE-VYZ in Jaslovske Bohunice and after immobilisation are deposited in National Radwaste Repository Mochovce (RU RAO). After filling of the RU RAO, FRCC will be stored during 300 years. During this time the integrity of the FRCC must be guaranteed. By the influence of autoradiolysis of the cellulose and bituminized radwastes as well as in cement grout the gases are formed, mainly the hydrogen, methane and carbon dioxide. In the case of presence of available water (a w ≥ 0.63) and in presence of microbes and moulds at appropriate conditions the biological decomposition of cellulose materials may proceed with formation of H 2 , CH 4 a CO 2 . With increasing of developed gases may increase pressure in FRCC, that may initiate the loss of integrity of the FRCC with following endangering of radiation safety of the RU RAO, respectively of the territory over the repository.Authors developed the new mathematical model of pressure of gases in FRCC and in deposited barrels with cellulose and bituminized radwastes. The mathematical model is based on biological decomposition of cellulose materials as well as on radiation decomposition of cellulose, bitumen and concrete. In this mathematical model the diffusion through the walls of FRCC is the main process responsible for decreasing of the pressure. This model was developed in two basic variants: (1) Mathematical model of gas pressure in FRCC as function of dose; (2) Mathematical model of gas pressure in FRCC as function of mass of cellulose

Physical and chemical characteristics of cashew nut flour stored and packaged with different packages

Directory of Open Access Journals (Sweden)

Bruna Carolina GADANI

Full Text Available Abstract The aim of this study was to evaluate the physical and chemical changes in cashew nut flour under different packaging and storage conditions. The flour samples were characterized according to their chemical composition, packaged in polystyrene trays associated with covering chloride polyvinyl (PVC, plastic pot of polyethylene terephthalate (PET, plastic packaging polyethylene (POL and without coating polystyrene trays (CON. All packages were stored for 225 days, evaluating every 45 days the moisture content of the flour as well as extracting their oil by the cold method for characterization on the following indexes: acidity, saponification, iodine, peroxide and refraction. There was slight and gradual increase in the moisture content from the 45th to the 225th day, especially for products packaged in PVC and without coating polystyrene trays (CON. The oil saponification indexes showed gradual decrease during storage, especially in flour without packaging (CON. There was a gradual increase in the iodine index until the 135th day, followed by decay. The acidity and peroxide indexes increased along with the storage time. However packages with lower oxygen and moisture permeability, such as PET and POL, minimized such changes, being therefore the most suitable for long-term storage.

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2008-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the pplication.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2009-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

RH Packaging Program Guidance

International Nuclear Information System (INIS)

2008-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package (also known as the 'RH-TRU 72-B cask') and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous

RH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 Code of Federal Regulations (CFR) 1.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these

Safety analysis report: packages. LP-12 tritium package (packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Gates, A.A.; McCarthy, P.G.; Edl, J.W.

1975-05-01

Elemental tritium is shipped at low pressure in a stainless steel container (LP-12) within an aluminum vessel and surrounded by 3.9 in.-thick Celotex insulation in a steel drum. Information is presented on the packaging design, evaluation of the structural, thermal, containment, shielding, and criticality characteristics of the package, procedures for loading, unloading, transporting, and testing the LP-12, and quality assurance requirements. (U.S.)

40 CFR 157.27 - Unit packaging.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Unit packaging. 157.27 Section 157.27 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS PACKAGING REQUIREMENTS FOR PESTICIDES AND DEVICES Child-Resistant Packaging § 157.27 Unit packaging. Pesticide products...

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2005-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP charges the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.

40 CFR 262.30 - Packaging.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Packaging. 262.30 Section 262.30... APPLICABLE TO GENERATORS OF HAZARDOUS WASTE Pre-Transport Requirements § 262.30 Packaging. Before... the waste in accordance with the applicable Department of Transportation regulations on packaging...

Project monitoring package (PMP) : A package for project activity monitoring

International Nuclear Information System (INIS)

Vyas, K.N.; Kannan, A.; Susandhi, R.; Basu, S.

1987-01-01

A package for preparing PERT/CPM network diagrams has been written for PDP-11/34. The program uses PLOT-10 library calls for device interfacing. The package is essentially non-interactive in nature, and reads input data in the form of activity description and duration. It calculates the critical path time and performs time scaling of the events. The report gives a brief outline of the logic used, a sample plot and tabular output for reference. An additional facility for performing project activity monitoring has also been implemented. Activity monitoring generally requires various reports such as feed back reports from various group co-ordinators, information report for project co-ordinator and brief periodical reports for management. A package 'DATATRIEVE' (DTR) on PDP-11/34 system is utilized for generating the above mentioned reports. As DTR can also use normal sequential files, an interfacing program has been written which reformats the files accepted by PERT program acceptable to DTR. Various types of reports as generated by DTR are included. However this part of the package is not transportable and can be implemented only on systems having DTR. 6 figures. (author)

Perfume Packaging, Seduction and Gender

Directory of Open Access Journals (Sweden)

Magdalena Petersson McIntyre

2013-06-01

Full Text Available This article examines gender and cultural sense-making in relation to perfumes and their packaging. Gendered meanings of seduction, choice, consumption and taste are brought to the fore with the use of go-along interviews with consumers in per-fume stores. Meeting luxury packages in this feminized environment made the interviewed women speak of bottles as objects to fall in love with and they de-scribed packages as the active part in an act of seduction where they were expect-ing packages to persuade them into consumption. The interviewed men on the other hand portrayed themselves as active choice-makers and stressed that they were always in control and not seduced by packaging. However, while their ways of explaining their relationship with packaging on the surface seems to confirm cultural generalizations in relation to gender and seduction, the article argues that letting oneself be seduced is no less active than seducing. Based on a combination of actor network theories and theories of gender performativity the article points to the agency of packaging for constructions of gender and understands the inter-viewees as equally animated by the flows of passion which guide their actions.

Naval Waste Package Design Sensitivity

International Nuclear Information System (INIS)

T. Schmitt

2006-01-01

The purpose of this calculation is to determine the sensitivity of the structural response of the Naval waste packages to varying inner cavity dimensions when subjected to a comer drop and tip-over from elevated surface. This calculation will also determine the sensitivity of the structural response of the Naval waste packages to the upper bound of the naval canister masses. The scope of this document is limited to reporting the calculation results in terms of through-wall stress intensities in the outer corrosion barrier. This calculation is intended for use in support of the preliminary design activities for the license application design of the Naval waste package. It examines the effects of small changes between the naval canister and the inner vessel, and in these dimensions, the Naval Long waste package and Naval Short waste package are similar. Therefore, only the Naval Long waste package is used in this calculation and is based on the proposed potential designs presented by the drawings and sketches in References 2.1.10 to 2.1.17 and 2.1.20. All conclusions are valid for both the Naval Long and Naval Short waste packages

Radioactive material packaging performance testing

International Nuclear Information System (INIS)

Romano, T.

1992-06-01

In an effort to provide uniform packaging of hazardous material on an international level, recommendations for the transport of dangerous goods have been developed by the United Nations. These recommendations are performance oriented and contrast with a large number of packaging specifications in the US Department of Transportation's hazard materials regulations. This dual system presents problems when international shipments enter the US Department of Transportation's system. Faced with the question of continuing a dual system or aligning with the international system, the Research and Special Programs Administration of the US Department of Transportation responded with Docket HM-181. This began the transition toward the international transportation system. Following close behind is Docket HM-169A, which addressed low specific activity radioactive material packaging. This paper will discuss the differences between performance-oriented and specification packaging, the transition toward performance-oriented packaging by the US Department of Transportation, and performance-oriented testing of radioactive material packaging by Westinghouse Hanford Company. Dockets HM-181 and HM-169A will be discussed along with Type A (low activity) and Type B (high activity) radioactive material packaging evaluations

RASPLAV package

International Nuclear Information System (INIS)

1990-01-01

The RASPLAV package for investigation of post-accident mass transport and heat transfer processes is presented. The package performs three dimensional thermal conduction calculations in space nonuniform and temperature dependent conductivities and variable heat sources, taking into account phase transformations. The processes of free-moving bulk material, mixing of melting fuel due to advection and dissolution, and also evaporation/adsorption are modelled. Two-dimensional hydrodynamics with self-consistent heat transfer are also performed. The paper briefly traces the ways the solution procedures are carried out in the program package and outlines the major results of the simulation of reactor vessel melting after a core meltdown. The theoretical analysis and the calculations in this case were carried out in order to define the possibility of localization of the zone reminders. The interactions between the reminders and the concrete are simulated and evaluation of the interaction parameters is carried out. 4 refs. (R.Ts)

7 CFR 58.640 - Packaging.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Packaging. 58.640 Section 58.640 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.640 Packaging. The packaging of the semifrozen product shall be done by means which will in...

Emergency response packaging: A conceptual outline

International Nuclear Information System (INIS)

Luna, R.E.; McClure, J.D.; Bennett, P.C.; Wheeler, T.A.

1992-01-01

The Packaging and Transportation Needs in the 1990's (PATN) component of the Transportation Assessment and Integration (TRAIN) program (DOE Nov. 1991) was designed to survey United States Department of Energy programs, both ongoing and planned, to identify needs for packaging and transportation services over the next decade. PATN also identified transportation elements that should be developed by the DOE Office of Environmental Restoration and Waste Management (DOE EM) Transportation Management Program (TMP). As a result of the predominant involvement of the TMP in radioactive material shipment issues and DOE EM's involvement with waste management issues, the primary focus of PATN was on waste packaging issues. Pending DOE regulations will formalize federal guidelines and regulations for transportation of hazardous and radioactive materials within the boundaries of DOE reservations and facilities and reflect a growing awareness of concern regarding safety environmental responsibility activities on DOE reservations. Future practices involving the transportation of radioactive material within DOE reservations will closely parallel those used for commercial and governmental transportation across the United States. This has added to the perceived need for emergency recovery packaging and emergency response features on primary packaging, for both on-site shipments and shipments between DOE facilities (off-site). Historically, emergency response and recovery functions of packaging have not been adequately considered in packaging design and construction concepts. This paper develops the rationale for emergency response packaging, including both overpack concepts for repackaging compromised packaging and primary packaging redesign to facilitate the recovery of packages via mobile remote handling equipment. The rationale will examine concepts for determination of likely use patterns to identify types of shipments where recovery packaging may have the most favorable payoff

Sustainable packaging. Packaging for a circular economy; Duurzaam verpakken. Verpakken voor de circulaire economie

Energy Technology Data Exchange (ETDEWEB)

Haffmans, S. [Partners for Innovation, Amsterdam (Netherlands); Standhardt, G. [Nederlands Verpaskkingscentrum NVC, Gouda (Netherlands); Hamer, A. [Agentschap NL, Utrecht (Netherlands)

2013-10-15

What is Sustainable Packaging? And what is the most sustainable packaging for a product? The publication is intended for anyone who wants to take into account the environment in the design of a product and packaging. It offers concrete suggestions and inspiring examples to bring sustainable packaging into practice [Dutch] Wat is Duurzaam Verpakken? En wat is de duurzaamste verpakking voor mijn product? De publicatie is bestemd voor iedereen die rekening wil houden met het milieu bij het ontwerp van een product-verpakkingscombinatie. Ze biedt concrete aanknopingspunten en inspirerende voorbeelden om hier praktisch mee aan de slag te gaan.

AN ADA NAMELIST PACKAGE

Science.gov (United States)

Klumpp, A. R.

1994-01-01

The Ada Namelist Package, developed for the Ada programming language, enables a calling program to read and write FORTRAN-style namelist files. A namelist file consists of any number of assignment statements in any order. Features of the Ada Namelist Package are: the handling of any combination of user-defined types; the ability to read vectors, matrices, and slices of vectors and matrices; the handling of mismatches between variables in the namelist file and those in the programmed list of namelist variables; and the ability to avoid searching the entire input file for each variable. The principle user benefits of this software are the following: the ability to write namelist-readable files, the ability to detect most file errors in the initialization phase, a package organization that reduces the number of instantiated units to a few packages rather than to many subprograms, a reduced number of restrictions, and an increased execution speed. The Ada Namelist reads data from an input file into variables declared within a user program. It then writes data from the user program to an output file, printer, or display. The input file contains a sequence of assignment statements in arbitrary order. The output is in namelist-readable form. There is a one-to-one correspondence between namelist I/O statements executed in the user program and variables read or written. Nevertheless, in the input file, mismatches are allowed between assignment statements in the file and the namelist read procedure statements in the user program. The Ada Namelist Package itself is non-generic. However, it has a group of nested generic packages following the nongeneric opening portion. The opening portion declares a variety of useraccessible constants, variables and subprograms. The subprograms are procedures for initializing namelists for reading, reading and writing strings. The subprograms are also functions for analyzing the content of the current dataset and diagnosing errors. Two nested

21 CFR 820.130 - Device packaging.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Device packaging. 820.130 Section 820.130 Food and... QUALITY SYSTEM REGULATION Labeling and Packaging Control § 820.130 Device packaging. Each manufacturer shall ensure that device packaging and shipping containers are designed and constructed to protect the...

76 FR 30551 - Specifications for Packagings

Science.gov (United States)

2011-05-26

... design qualification test and each periodic retest on a packaging, a test report must be prepared. The... where the design qualification tests are conducted, for as long as the packaging is produced and for at... report; (5) Manufacturer of the packaging; (6) Description of the packaging design type (e.g. dimensions...

Thermal relaxation of bituminous coal to improve donation ability of hydrogen radicals in flash pyrolysis; Sekitan kozo kanwa ni yoru suiso radical kyoyo noryoku no kojo wo mezashita netsubunkai mae shori

Energy Technology Data Exchange (ETDEWEB)

Mori, T.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

1996-10-28

In terms of coal conversion reaction, the behavior of bituminous coal heated beyond a glass transition point was examined on the basis of pyrolyzed products, and the effect of an increase in proton mobility on promotion of coal decomposition was evaluated. In experiment, after Illinois bituminous coal specimen was heated up to a specific temperature in N2 or He gas flow at a rate of 5K/min, the specimen was directly transferred to a pyrolyzer for instantaneous pyrolysis. As the experimental result, the glass transition temperature of the Illinois coal specimen was calculated to be 589K from a differential scanning calorimetry (DSC) profile. From the pyrolysis result of the Illinois coal specimen heated up to 623K, the char yield decreased by 3kg as compared with that of the original coal, while the tar yield increased by 4kg up to 27kg per 100kg of the original coal. This tar increase was larger than that of cooled coal. These results suggested that the donation of hydrogen radicals to coal fragments is improved with an increase in proton mobility. 4 refs., 4 figs., 1 tab.

Dossier Imitation - Introduction générale Special section on Imitation – General introduction

Directory of Open Access Journals (Sweden)

Odile Petit

2009-10-01

Full Text Available Dans ce dossier spécial, nous nous sommes intéressés à l’aspect ontogénique et phylogénique de l’imitation. Nous avons invité des spécialistes du développement de l’enfant et des primatologues à discuter de ce que l’imitation représente pour l’espèce humaine, de sa présence chez des espèces de primates non humains et des éventuelles similarités observées au sein de l’ordre des primates. L’imitation possède une double dimension, cognitive et sociale. En effet, les processus d’imitation impliquent des compétences cognitives qui s’inscrivent dans des contextes sociaux et culturels. Ce mode d’apprentissage soulève de nombreuses questions : Peut-on considérer l’imitation comme une compétence innée ? L’étude de son développement permet-elle de comprendre les mécanismes du fonctionnement cognitif ? L’imitation est-elle uniquement humaine ?This special issue is interested in the ontogeny and the phylogeny of imitation. We have invited experts in developmental psychology and in primatology to discuss the definition of imitation in Human, its existence in non human primate species and to address the question of similarities between the different primate species. Imitation has both a cognitive and a social dimension. Imitation involves, indeed, cognitive processes that are part of social and cultural life. Learning occurs via imitation and several questions can be asked: Is imitation innate? Will studying its ontogeny help understanding its cognitive processes? Finally, is imitation human specific?

Cigarette smoking and federal black lung benefits in bituminous coal miners.

Science.gov (United States)

Roy, T M; Collins, L C; Snider, H L; Anderson, W H

1989-02-01

The records of 1000 consecutive coal miners applying for benefits under the Federal Coal Mine Health and Safety Act were examined to determine the contribution of age, dust accumulation, and cigarette smoking to the profile of the miner who satisfies the current pulmonary criteria for disability. Using the presence of pneumoconiosis on chest radiograph as the indication of significant coal dust accumulation, the miners were separated into Group A--those without pneumoconiosis (n = 316) and Group B--those with pneumoconiosis (n = 684). The federal spirometric criteria for disability identified 55/316 miners in Group A (14.5%) and 99/684 miners in Group B (17.4%) potentially eligible for an award (P = .27). The mean ages of miners in both groups did not differ significantly, nor was there difference in the mean ages of groups that did or did not meet the federal criteria. In both groups, those miners potentially eligible for a financial award smoked more cigarettes than did their counterparts (Group A, 31.0 v 18.5 pack-years, P less than .001; Group B, 31.3 v 23.6 pack-years, P less than .001). There was no difference in the smoking histories of the miners from either group who met the federal criteria. Our data indicate that, in the case of bituminous coal miners, the present federal legislation intended to identify and remunerate those who suffer lung impairment from chronic occupational exposure to coal dust is biased in favor of those who sustain additional damage to their ventilatory capacity by smoking cigarettes.

Package Formats for Preserved Digital Material

DEFF Research Database (Denmark)

Zierau, Eld

2012-01-01

This paper presents an investigation of the best suitable package formats for long term digital preservation. The choice of a package format for preservation is crucial for future access, thus a thorough analysis of choice is important. The investigation presented here covers setting up requireme......This paper presents an investigation of the best suitable package formats for long term digital preservation. The choice of a package format for preservation is crucial for future access, thus a thorough analysis of choice is important. The investigation presented here covers setting up...... requirements for package formats used for long term preserved digital material, and using these requirements as the basis for analysing a range of package formats. The result of the concrete investigation is that the WARC format is the package format best suited for the listed requirements. Fulfilling...

Directory of Certificates of Compliance for Radioactive-Materials Packages. Summary report of NRC approved packages

International Nuclear Information System (INIS)

1983-01-01

This directory contains a Summary Report of the US Nuclear Regulatory Commission's Approved Packages (Volume I), all Certificates of Compliance (Volume 2), and Summary Report of NRC Approved Quality Assurance Programs (Volume 3) for Radioactive Material Packages effective December 31, 1982. The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the back of Volumes 1 and 2 of the directory. A listing by packaging types is included in the back of Volume 2. An alphabetical listing by company name is included in the back of Volume 3 for approved QA programs. The Summary Reports include a listing of all users of each package design and approved QA programs prior to the publication date of the directory

9 CFR 354.72 - Packaging.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Packaging. 354.72 Section 354.72... CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Supervision of Marking and Packaging § 354.72 Packaging. No container which bears or may bear any official identification or any abbreviation...

Antimicrobial packaging with natural compunds - a review

Directory of Open Access Journals (Sweden)

Renata Dobrucka

2016-12-01

Full Text Available Background:  Packaging problems are an integral part of logistics and the implementation of packaging significantly affects the effectiveness of logistics processes, as a factor which increases the safety and the quality of products being transported. Active packaging is an area of technology needed to meet the requirements of the contemporary consumer. Active packaging creates additional opportunities in systems for packing goods, as well as offering a solution in which the packaging, the product and surroundings interact. Furthermore, active packaging allows packaging to interact with food and the environment and play a dynamic role in food preservation. The main role of antimicrobial packaging is to inhibit the growth of microorganisms that reduce the quality of the packaged product. Methods: The application of natural antimicrobial agents appears to be safe for food products. Also, these compounds have potential applications as a natural preservative in the food packaging industry. This study presents some antibacterial agents, namely chitosan, nisin and pectins. Results and conclusion: Natural substances used in active packaging can eliminate the danger of chemical substances migrating to food.

Overview of the DOE packaging certification process

Energy Technology Data Exchange (ETDEWEB)

Liu, Y.Y.; Carlson, R.D. [Argonne National Lab., IL (United States); Carlson, R.W. [Lawrence Livermore National Lab., CA (United States); Kapoor, A. [USDOE, Washington, DC (United States)

1995-12-31

This paper gives an overview of the DOE packaging certification process, which is implemented by the Office of Facility Safety Analysis, under the Assistance Secretary for Environment, Safety and Health, for packagings that are not used for weapons and weapons components, nor for naval nuclear propulsion. The overview will emphasize Type B packagings and the Safety Analysis Report for Packaging (SARP) review that parallels the NRC packaging review. Other important elements in the DOE packaging certification program, such as training, methods development, data bases, and technical assistance, are also emphasized, because they have contributed significantly to the improvement of the certification process since DOE consolidated its packaging certification function in 1985. The paper finishes with a discussion of the roles and functions of the DOE Packaging Safety Review Steering Committee, which is chartered to address issues and concerns of interest to the DOE packaging and transportation safety community. Two articles related to DOE packaging certification were published earlier on the SARP review procedures and the DOE Packaging Review Guide. These articles may be consulted for additional information.

Safety analysis report: packages. LP-50 tritium package (packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Gates, A.A.; McCarthy, P.G.; Edl, J.W.

1975-04-01

Elemental tritium is shipped at low pressure in a stainless steel container (LP-50) sealed within an aluminum vessel and surrounded by a minimum of 4-in. thick Celotex insulation in a steel drum. The structural, thermal, containment, shielding, and criticality safety aspects of this package are evaluated. Procedures for loading and unloading, empty cask transport, acceptance testing and maintenance, and quality assurance requirements for the LP-50 package are described in detail. (U.S.)

Safety analysis report; packages LP-50 tritium package. (Packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Gates, A.A.; McCarthy, P.G.; Edl, J.W.; Chalfant, G.G.

1975-05-01

Elemental tritium is shipped at low pressure in a stainless steel container (LP-50) surrounded by an aluminum vessel and Celotex insulation at least 4 in. thick in a steel drum. The total weight of the package is 260 lbs maximum. The various components that constitute the package are described and are shown in 7 figures. The safety analysis includes: structural evaluations; thermal evaluations; containment; operating procedures; acceptance tests and maintenance program; and design review

Large transport packages for decommissioning waste

International Nuclear Information System (INIS)

Price, M.S.T.

1988-08-01

This document reports progress on a study of large transport packages for decommissioning waste and is the semi-annual report for the period 1 January - 30 June 1988. The main tasks performed during the period related to the assembly of package design criteria ie those aspects of manufacture, handling, storage, transport and disposal which impose constraints on design. This work was synthesised into a design specification for packages which formed the conclusion of that task and was the entry into the final task - the development of package design concepts. The design specifications, which concentrated on the Industrial Package category of the IAEA Transport Regulations, has been interpreted for the two main concepts (a) a self-shielded package disposed of in its entirety and (b) a package with returnable shielding. Preliminary information has been prepared on the cost of providing the package as well as transport to a repository and disposal. There is considerable uncertainty about the cost of disposal and variations of over a factor of 10 are possible. Under these circumstances there is merit in choosing a design concept which is relatively insensitive to disposal cost variations. The initial results indicate that on these grounds the package with returnable shielding is preferred. (author)

Innovative Approaches to Large Component Packaging

International Nuclear Information System (INIS)

Freitag, A.; Hooper, M.; Posivak, E.; Sullivan, J.

2006-01-01

Radioactive waste disposal often times requires creative approaches in packaging design, especially for large components. Innovative design techniques are required to meet the needs for handling, transporting, and disposing of these large packages. Large components (i.e., Reactor Pressure Vessel (RPV) heads and even RPVs themselves) require special packaging for shielding and contamination control, as well as for transport and disposal. WMG Inc designed and used standard packaging for RPV heads without control rod drive mechanisms (CRDMs) attached for five RPV heads and has also more recently met an even bigger challenge and developed the innovative Intact Vessel Head Transport System (IVHTS) for RPV heads with CRDMs intact. This packaging system has been given a manufacturer's exemption by the United States Department of Transportation (USDOT) for packaging RPV heads. The IVHTS packaging has now been successfully used at two commercial nuclear power plants. Another example of innovative packaging is the large component packaging that WMG designed, fabricated, and utilized at the West Valley Demonstration Project (WVDP). In 2002, West Valley's high-level waste vitrification process was shut down in preparation for D and D of the West Valley Vitrification Facility. Three of the major components of concern within the Vitrification Facility were the Melter, the Concentrate Feed Makeup Tank (CFMT), and the Melter Feed Holdup Tank (MFHT). The removal, packaging, and disposition of these three components presented significant radiological and handling challenges for the project. WMG designed, fabricated, and installed special packaging for the transport and disposal of each of these three components, which eliminated an otherwise time intensive and costly segmentation process that WVDP was considering. Finally, WMG has also designed and fabricated special packaging for both the Connecticut Yankee (CY) and San Onofre Nuclear Generating Station (SONGS) RPVs. This paper

RF and microwave microelectronics packaging II

CERN Document Server

Sturdivant, Rick

2017-01-01

Reviews RF, microwave, and microelectronics assembly process, quality control, and failure analysis Bridges the gap between low cost commercial and hi-res RF/Microwave packaging technologies Engages in an in-depth discussion of challenges in packaging and assembly of advanced high-power amplifiers This book presents the latest developments in packaging for high-frequency electronics. It is a companion volume to “RF and Microwave Microelectronics Packaging” (2010) and covers the latest developments in thermal management, electrical/RF/thermal-mechanical designs and simulations, packaging and processing methods, and other RF and microwave packaging topics. Chapters provide detailed coverage of phased arrays, T/R modules, 3D transitions, high thermal conductivity materials, carbon nanotubes and graphene advanced materials, and chip size packaging for RF MEMS. It appeals to practicing engineers in the electronic packaging and high-frequency electronics domain, and to academic researchers interested in underst...

Study of stabilization/solidification processes (of solid porous wastes) based on hydraulic or bituminous binders; Etude des procedes de stabilisation/solidification (des dechets solides poreux) a base de liants hydrauliques ou de liants bitumineux

Energy Technology Data Exchange (ETDEWEB)

Sing-Teniere, Ch.

1998-02-01

The first part of this thesis presents the regulatory framework and the technical context linked with the study of stabilized/solidified wastes and with the evaluation of stabilization/solidification processes. A presentation of the two type of ultimate wastes under study (a used catalyst and an activated charcoal) and an analysis of the processes is given. The second part is devoted to the experimental characterization of both types of porous wastes. The third part deals with the processing of such wastes using an hydraulic binder. The study stresses on both on the stabilization/solidification efficiency of the process and on the conditions of its implementation. The same work is made for a process that uses a bituminous binder. Some choice criteria for the selection of the better process are deduced from the examination of the overall data collected. The waste characterization methodology is applied six times: two times for the raw wastes, two times for the same wastes processed with an hydraulic binder, and two times for the same wastes processed with a bituminous binder. (J.S.)

49 CFR 173.3 - Packaging and exceptions.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Packaging and exceptions. 173.3 Section 173.3... SHIPMENTS AND PACKAGINGS General § 173.3 Packaging and exceptions. (a) The packaging of hazardous materials.... standard packaging must be open to inspection by a representative of the Department. (b) The regulations...

Analysis of the use of coal tar as a binder in bituminous mixtures, using Marshall and Ramcodes methodologies

International Nuclear Information System (INIS)

Ochoa-Díaz, R

2013-01-01

This paper presents an alternative use of coal tar, a by-product of the steel industry, given the problems of accumulation and negative environmental impact. Therefore, it is necessary to analyze the incorporation of coal tar as a binder in paving mixtures. First, this paper presents the origin, description of the main characteristics, and properties of tar. Then, this paper evaluates the mix of coal tar by means of the RAMCODES and Marshall methodologies to determine its resistance. The results of the tests explain the physical and mechanical properties of the mix. Taking into account the results of both methods, this paper makes a comparison to determine the suitability of the RAMCODES methodology in the mix design. Finally, it analyzes the alternatives to coal tar that can be used as binders in bituminous mixes for pavement and the advantages of their uses under some specific conditions

Materials for advanced packaging

CERN Document Server

Wong, CP

2017-01-01

This second edition continues to be the most comprehensive review on the developments in advanced electronic packaging technologies, with a focus on materials and processing. Recognized experts in the field contribute to 22 updated and new chapters that provide comprehensive coverage on various 3D package architectures, novel bonding and joining techniques, wire bonding, wafer thinning techniques, organic substrates, and novel approaches to make electrical interconnects between integrated circuit and substrates. Various chapters also address advances in several key packaging materials, including: Lead-free solders Flip chip underfills Epoxy molding compounds Conductive adhesives Die attach adhesives/films Thermal interface materials (TIMS) Materials for fabricating embedded passives including capacitors, inductors, and resistors Materials and processing aspects on wafer-level chip scale package (CSP) and MicroElectroMechanical system (MEMS) Contributors also review new and emerging technologies such as Light ...

Biobased Packaging - Application in Meat Industry

Directory of Open Access Journals (Sweden)

S. Wilfred Ruban

2009-04-01

Full Text Available Because of growing problems of waste disposal and because petroleum is a nonrenewable resource with diminishing quantities, renewed interest in packaging research is underway to develop and promote the use of “bio-plastics.” In general, compared to conventional plastics derived from petroleum, bio-based polymers have more diverse stereochemistry and architecture of side chains which enable research scientists a greater number of opportunities to customize the properties of the final packaging material. The primary challenge facing the food (Meat industry in producing bio-plastic packaging, currently, is to match the durability of the packaging with product shelf-life. Notable advances in biopolymer production, consumer demand for more environmentally-friendly packaging, and technologies that allow packaging to do more than just encompass the food are driving new and novel research and developments in the area of packaging for muscle foods. [Vet. World 2009; 2(2.000: 79-82

Hermeticity of electronic packages

CERN Document Server

Greenhouse, Hal; Romenesco, Bruce

2011-01-01

This is a book about the integrity of sealed packages to resist foreign gases and liquids penetrating the seal or an opening (crack) in the packageùespecially critical to the reliability and longevity of electronics. The author explains how to predict the reliability and the longevity of the packages based on leak rate measurements and the assumptions of impurities. Non-specialists in particular will benefit from the author's long involvement in the technology. Hermeticity is a subject that demands practical experience, and solving one problem does not necessarily give one the background to so

Hermeticity of electronic packages

CERN Document Server

Greenhouse, Hal

2000-01-01

This is a book about the integrity of sealed packages to resist foreign gases and liquids penetrating the seal or an opening (crack) in the package-especially critical to the reliability and longevity of electronics. The author explains how to predict the reliability and the longevity of the packages based on leak rate measurements and the assumptions of impurities. Non-specialists in particular will benefit from the author's long involvement in the technology. Hermeticity is a subject that demands practical experience, and solving one problem does not necessarily give one the background to so

Étude sur les déterminants de l'intention des infirmières de première ligne d'utliser le Dossier de santé du Québec (DSQ) dans leurs activités cliniques

OpenAIRE

Leblanc, Geneviève

2011-01-01

Les technologies de l’information et des communications sont perçues comme étant une solution potentielle aux problèmes actuels du système de santé québécois. Elles peuvent servir d’outils qui soutiennent les organisations et les pratiques professionnelles afin d’augmenter la qualité et l’efficience des soins et des services de santé. Au Québec, le Dossier de santé du Québec (DSQ) est considéré comme étant la pierre angulaire permettant l’intégration d’un ensemble d’informations utiles au sui...

Directory of certificates of compliance for radioactive materials packages; Summary Report of NRC Approved Packages

International Nuclear Information System (INIS)

1980-12-01

This directory contains a Summary Report of NRC approved Packages (Volume 1), Certificates of Compliance (Volume 2), and a Summary Report of NRC Approved Quality Assurance Programs for Radioactive Material Packages (Volume 3). The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the U.S. Nuclear Regulatory Commission. To assist in identifying packaging, and index by Model Number and corresponding Certificate of Compliance number is included at the back of each volume of the directory. The Summary Report includes a listing of all users of each package design prior to the publication date of the directory. Shipments of radioactive material using these packagings must be in accordance with the provisions of 49 CFR 173.393a and 10 CFR Part 71, as applicable. In satisfying the requirements of Section 71.12, it is the responsibility of the licensees to insure them--that they have a copy of the current approval and conduct their transportation activities in accordance with an NRC approved quality assurance program

Fiscal 1989 report on the bituminous coal liquefaction section meeting; 1989 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are given and discussions are made about the progress of research and development. Reported and discussed in relation to the progress of the pilot plant support research are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); development of an optimum decalcification technique (Sumitomo Coal Mining Co., Ltd., and Sumitomo Metal Industries, Ltd.); studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.); and studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.). In relation to studies using a bituminous coal liquefaction pilot plant, the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil, Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.) are reported and discussed, the latter covering liquefaction solvent performance optimization, slurry preheating furnaces, coal slurry properties, and so forth. (NEDO)

Fiscal 1990 report on the bituminous coal liquefaction section meeting; 1990 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are delivered and discussions are made concerning the progress of research and development activities. Reported and discussed in relation to the pilot plant support research, etc., are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); development of an optimum coal refining technique (Sumitomo Coal Mining Co., Ltd.); development of an optimum pretreatment technique and improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.); and studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.). Reported and discussed in relation to researches using a bituminous coal liquefaction pilot plant are the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.), the latter covering liquefaction solvent performance optimization, slurry pre-heating furnaces, coal slurry properties, and so forth. (NEDO)

Thermogravimetric analysis of the behavior of sub-bituminous coal and cellulosic ethanol residue during co-combustion.

Science.gov (United States)

Buratti, C; Barbanera, M; Bartocci, P; Fantozzi, F

2015-06-01

The influence of the addition of cellulosic ethanol residue (CER) on the combustion of Indonesian sub-bituminous coal was analyzed by non isothermal thermo-gravimetric analysis (TGA). The effect of blends ratio (5%, 10%, 15% and 20%), interaction mechanism, and heating rate (5°C/min, 10°C/min, 15°C/min, 20°C/min) on the combustion process was studied. The results show that the increase of the blending ratio allows to achieve the increase of the combustibility index from 7.49E-08 to 5.26E-07 at the blending ratio of 20%. Two types of non-isothermal kinetic analysis methods (Ozawa-Flynn-Wall and Vyazovkin) were also applied. Results indicate that the activation energy of the blends decreases with increasing the conversion rate. In particular, the blending ratio of 20% confirms to have the better combustion performance, with the average value of the activation energy equal to 41.10 kJ/mol obtained by Ozawa-Flynn-Wall model and 31.17 kJ/mol obtained by Vyazovkin model. Copyright © 2015 Elsevier Ltd. All rights reserved.

Energy and packaging

Energy Technology Data Exchange (ETDEWEB)

Boustead, I; Hancock, G F

1981-01-01

Information is given on the energy and raw materials required in the production and use of containers used to package beer, cider, and carbonated soft drinks in the United Kingdom. Topics covered include: methodology of energy analysis, primary and secondary fuels, transport, packaging materials, including glass, aluminum, iron, steel, and tinplate, container production, including plastic bottles, distribution of empty containers, filling and packing, distribution, and disposal. (LEW)

Signalling product healthiness through symbolic package cues: Effects of package shape and goal congruence on consumer behaviour.

Science.gov (United States)

van Ooijen, Iris; Fransen, Marieke L; Verlegh, Peeter W J; Smit, Edith G

2017-02-01

Three studies show that product packaging shape serves as a cue that communicates healthiness of food products. Inspired by embodiment accounts, we show that packaging that simulates a slim body shape acts as a symbolic cue for product healthiness (e.g., low in calories), as opposed to packaging that simulates a wide body shape. Furthermore, we show that the effect of slim package shape on consumer behaviour is goal dependent. Whereas simulation of a slim (vs. wide) body shape increases choice likelihood and product attitude when consumers have a health-relevant shopping goal, packaging shape does not affect these outcomes when consumers have a hedonic shopping goal. In Study 3, we adopt a realistic shopping paradigm using a shelf with authentic products, and find that a slim (as opposed to wide) package shape increases on-shelf product recognition and increases product attitude for healthy products. We discuss results and implications regarding product positioning and the packaging design process. Copyright © 2016 Elsevier Ltd. All rights reserved.

ACTIVE PACKAGING SYSTEM FOR MEAT AND MEAT PRODUCTS

Directory of Open Access Journals (Sweden)

Adriana Pavelková

2012-10-01

Full Text Available In the recent past, food packaging was used to enable marketing of products and to provide passive protection against environmental contaminations or influences that affect the shelf life of the products. However, unlike traditional packaging, which must be totally inert, active packaging is designed to interact with the contents and/or the surrounding environment. Interest in the use of active packaging systems for meat and meat products has increased in recent years. Active packaging systems are developed with the goal of extending shelf life for foods and increasing the period of time that the food is high quality. Developments in active packaging have led to advances in many areas, including delayed oxidation and controlled respiration rate, microbial growth, and moisture migration. Active packaging technologies include some physical, chemical, or biological action which changes interactions between a package, product, and/or headspace of the package in order to get a desired outcome. Active packaging systems discussed include oxygen scavengers, carbon dioxide scavengers and emitters, moisture control agents, flavour/odour absorbers and releasers  and antimicrobial packaging technologies. Active packaging is typically found in two types of systems; sachets and pads which are placed inside of packages, and active ingredients that are incorporated directly into packaging materials.  Recognition of the benefits of active packaging technologies by the food industry, development of economically viable packaging systems and increased consumer acceptance is necessary for commercial realisation of these packaging technologies.doi:10.5219/205

FY 1992 report on the Coal Liquefaction Committee; 1992 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

The paper reported activities of the Coal Liquefaction Committee in FY 1992. In the 1st committee meeting, report/discussion were made of the summary of the FY 1992 R and D plan on the bituminous coal liquefaction, brown coal liquefaction and the common/basic technology. Further, the following were reported as topics: results of the operation by bituminous coal liquefaction PSU and small equipment, state of arrangement of the results of the brown coal liquefaction project, making of the basic policy for development of the common/basic technology, construction of package of coal liquefaction technology. In the 2nd committee meeting, the summary of the results of the FY 1992 R and D was reported/discussed. As to the development of bituminous coal liquefaction technology, study using pilot plant and support study were reported. Concerning the development of brown coal liquefaction technology, study using a 50t/d pilot plant and complementary study of operation. Relating to the development of the common/basic technology, trial manufacture/development of plant equipment/materials, survey of selection of coal kind, etc. The paper also reported a scheme on the evaluation of efficiency of the brown coal liquefaction process. (NEDO)

Power Electronics Packaging Reliability | Transportation Research | NREL

Science.gov (United States)

Packaging Reliability Power Electronics Packaging Reliability A photo of a piece of power electronics laboratory equipment. NREL power electronics packaging reliability research investigates the electronics packaging around a semiconductor switching device determines the electrical, thermal, and

Temperature induced development of porous structure of bituminous coal chars at high pressure

Directory of Open Access Journals (Sweden)

Natalia Howaniec

2016-01-01

Full Text Available The porous structure of chars affects their reactivity in gasification, having an impact on the course and product distribution of the process. The shape, size and connections between pores determine the mechanical properties of chars, as well as heat and mass transport in thermochemical processing. In the study the combined effects of temperature in the range of 973–1273 °K and elevated pressure of 3 MPa on the development of porous structure of bituminous coal chars were investigated. Relatively low heating rate and long residence time characteristic for the in-situ coal conversion were applied. The increase in the temperature to 1173 °K under pressurized conditions resulted in the enhancement of porous structure development reflected in the values of the specific surface area, total pore volume, micropore area and volume, as well as ratio of the micropore volume to the total pore volume. These effects were attributed to the enhanced vaporization and devolatilization, as well as swelling behavior along the increase of temperature and under high pressure, followed by a collapse of pores over certain temperature value. This proves the strong dependence of the porous structure of chars not only on the pyrolysis process conditions but also on the physical and chemical properties of the parent fuel.

Development of waste packages for TRU-disposal. 5. Development of cylindrical metal package for TRU wastes

International Nuclear Information System (INIS)

Mine, Tatsuya; Mizubayashi, Hiroshi; Asano, Hidekazu; Owada, Hitoshi; Otsuki, Akiyoshi

2005-01-01

Development of the TRU waste package for hulls and endpieces compression canisters, which include long-lived and low sorption nuclides like C-14 is essential and will contribute a lot to a reasonable enhancement of safety and economy of the TRU-disposal system. The cylindrical metal package made of carbon steel for canisters to enhance the efficiency of the TRU-disposal system and to economically improve their stacking conditions was developed. The package is a welded cylindrical construction with a deep drawn upper cover and a disc plate for a bottom cover. Since the welding is mainly made only for an upper cover and a bottom disc plate, this package has a better containment performance for radioactive nuclide and can reduce the cost for construction and manufacturing including its welding control. Furthermore, this package can be laid down in pile for stacking in the circular cross section disposal tunnel for the sedimentary rock, which can drastically minimize the space for disposal tunnel as mentioned previously in TRU report. This paper reports the results of the study for application of newly developed metal package into the previous TRU-disposal system and for the stacking equipment for the package. (author)

The development of a digital signal processing and plotting package to support testing of hazardous and radioactive material packages

International Nuclear Information System (INIS)

Ludwigsen, J.S.; Uncapher, W.L.; Arviso, M.; Lattier, C.N.; Hankinson, M.; Cannone, D.J.

1995-01-01

Federal regulations allow package designers to use analysis, testing, or a combination of analysis and testing to support certification of packages used to transport hazardous or radioactive materials. In recent years, many certified packages were subjected to a combination of analysis and testing. A major part of evaluating structural or thermal package response is the collection, reduction and presentation of instrumentation measurement data. Sandia National Laboratories, under the sponsorship of the US Department of Energy, has developed a comprehensive analysis and plotting package (known as KAPP) that performs digital signal processing of both transient structural and thermal data integrated with a comprehensive plotting package designed to support radioactive material package testing

The development of a packaging handbook

International Nuclear Information System (INIS)

Shappert, L.B.

1994-01-01

The Packaging Handbook, dealing with the development of packagings designed to carry radioactive material, is being written for DOE's Transportation and Packaging Safety Division. The primary goal of the Handbook is to provide sufficient technical information and guidance to improve the quality of Safety Analysis Reports on Type B Packagings (SARPs) that are submitted to DOE for certification. This paper provides an update on the status of the Handbook

Smart packaging systems for food applications: a review.

Science.gov (United States)

Biji, K B; Ravishankar, C N; Mohan, C O; Srinivasa Gopal, T K

2015-10-01

Changes in consumer preference for safe food have led to innovations in packaging technologies. This article reviews about different smart packaging systems and their applications in food packaging, packaging research with latest innovations. Active and intelligent packing are such packaging technologies which offer to deliver safer and quality products. Active packaging refers to the incorporation of additives into the package with the aim of maintaining or extending the product quality and shelf life. The intelligent systems are those that monitor the condition of packaged food to give information regarding the quality of the packaged food during transportation and storage. These technologies are designed to the increasing demand for safer foods with better shelf life. The market for active and intelligent packaging systems is expected to have a promising future by their integration into packaging materials or systems.

Development directions of packaging made from polymer materials

Directory of Open Access Journals (Sweden)

Jovanović Slobodan

2011-01-01

Full Text Available World packaging market achieves turnover of about $620 billion per year with one third of this amount being associated to packaging made from polymer materials. It is expected that this kind of packaging consumption will hold at least 3% of world packaging market share in the next five years and that it will surpass the consumption of all other materials used in the packaging production. This can be contributed to product quality, low production costs as well as significant investments made in the development of polymer materials, packaging technology and packaging. This paper presents some development directions for packaging made from polymer materials, such as: packaging in the protective atmosphere, the use of active and intelligent packaging, and the use of biopolymers and recycled polymers for packaging production that come into direct contact with the packed product.

49 CFR 178.915 - General Large Packaging standards.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false General Large Packaging standards. 178.915 Section... PACKAGINGS Large Packagings Standards § 178.915 General Large Packaging standards. (a) Each Large Packaging.... Large Packagings intended for solid hazardous materials must be sift-proof and water-resistant. (b) All...

Directory of certificates of compliance for radioactive materials packages: Summary report of NRC approved packages

International Nuclear Information System (INIS)

1987-11-01

This directory contains a Summary Report of the US Nuclear Regulatory Commission's Approved Packages (Volume 1). This directory makes available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the back of Volume 1

Interim storage of radioactive waste packages

International Nuclear Information System (INIS)

1998-01-01

This report covers all the principal aspects of production and interim storage of radioactive waste packages. The latest design solutions of waste storage facilities and the operational experiences of developed countries are described and evaluated in order to assist developing Member States in decision making and design and construction of their own storage facilities. This report is applicable to any category of radioactive waste package prepared for interim storage, including conditioned spent fuel, high level waste and sealed radiation sources. This report addresses the following issues: safety principles and requirements for storage of waste packages; treatment and conditioning methods for the main categories of radioactive waste; examples of existing interim storage facilities for LILW, spent fuel and high level waste; operational experience of Member States in waste storage operations including control of storage conditions, surveillance of waste packages and observation of the behaviour of waste packages during storage; retrieval of waste packages from storage facilities; technical and administrative measures that will ensure optimal performance of waste packages subject to various periods of interim storage

Design aspects of plutonium air-transportable packages

International Nuclear Information System (INIS)

Allen, G.C.; Moya, J.L.; Pierce, J.D.; Attaway, S.W.

1989-01-01

Recent worldwide interest in transporting plutonium powders by air has created a need for expanding the packaging technology base as well as improving their understanding of how plutonium air transport (PAT) packagings perform during severe accident tests. Historically it has not been possible to establish design rules for individual package components because of the complex way parts interacted in forming a successful whole unit. Also, computer analyses were only considered valid for very limited portions of the design effort because of large deformations, localized tearing occurring in the package during accident testing, and extensive use of orthotropic materials. Consequently, iterative design and experimentation has historically been used to develop plutonium air-transportable packages. Full-scale prototypes have been tested since scaling of packages utilizing wood as an energy absorber and thermal insulator has not proven to be very successful. This is because the wood grain and dynamic performance of the wood during crush do not always scale. The high cost of full-scale testing of large packages has certainly hindered obtaining additional data and development new designs. The testing criteria for PAT packages, as described in the US Nuclear Regulatory Commission's Qualification Criteria to Certify a Package for Air Transport of Plutonium, NUREG-0360, 1978, are summarized. Computer modeling techniques have greatly improved over the last ten years, and there are some areas of opportunity for future applications to plutonium air-transportable package design problems. Having developed a better understanding of the performance of current packages, they have the opportunity to make major improvements in new packaging concepts. Each of these areas is explored in further depth to establish their impact on design practices for air-transportable packages

Best Practice in Policy Package Design

DEFF Research Database (Denmark)

Kessler, Florian; Vesela, Jirina; Vencl, Vaclav

2010-01-01

This deliverable focuses on the identification and analysis of best practice examples of policy package design. For this purpose a methodology is developed that allows the systematic analysis of both national and EU policy packages. Eight packages were selected and analysed, highlighting...... the factors which supported the design and implementation process in each case. The results of the analysis show which factors led to these cases to be considered best practice. In addition, factors are identified which are not yet part of the generic policy packaging framework presented in earlier OPTIC...... Deliverables. The consideration of these factors will help to further improve the framework in the subsequent work packages....

Intelligent food packaging - research and development

OpenAIRE

Renata Dobrucka; Ryszard Cierpiszewski; Andrzej Korzeniowski

2015-01-01

Packaging also fosters effective marketing of the food through distribution and sale channels. It is of the utmost importance to optimize the protection of the food, a great quality and appearance - better than typical packaged foods. In recent years, intelligent packaging became very popular. Intelligent packaging is becoming more and more widely used for food products. Application of this type of solution contributes to improvement of the quality consumer life undoubtedly. Intelligent packa...

Unit-of-Use Versus Traditional Bulk Packaging

Directory of Open Access Journals (Sweden)

Tiffany So

2012-01-01

Full Text Available Background: The choice between unit-of-use versus traditional bulk packaging in the US has long been a continuous debate for drug manufacturers and pharmacies in order to have the most efficient and safest practices. Understanding the benefits of using unit-of-use packaging over bulk packaging by US drug manufacturers in terms of workflow efficiency, economical costs and medication safety in the pharmacy is sometimes challenging.Methods: A time-saving study comparing the time saved using unit-of-use packaging versus bulk packaging, was examined. Prices between unit-of-use versus bulk packages were compared by using the Red Book: Pharmacy’s Fundamental Reference. Other articles were reviewed on the topics of counterfeiting, safe labeling, and implementation of unit-of-use packaging. Lastly, a cost-saving study was reviewed showing how medication adherence, due to improved packaging, could be cost-effective for patients.Results: When examining time, costs, medication adherence, and counterfeiting arguments, unit-of-use packaging proved to be beneficial for patients in all these terms.

Unit-of-Use Versus Traditional Bulk Packaging

Directory of Open Access Journals (Sweden)

Tiffany So

2012-01-01

Full Text Available Background: The choice between unit-of-use versus traditional bulk packaging in the US has long been a continuous debate for drug manufacturers and pharmacies in order to have the most efficient and safest practices. Understanding the benefits of using unit-of-use packaging over bulk packaging by US drug manufacturers in terms of workflow efficiency, economical costs and medication safety in the pharmacy is sometimes challenging. Methods: A time-saving study comparing the time saved using unit-of-use packaging versus bulk packaging, was examined. Prices between unit-of-use versus bulk packages were compared by using the Red Book: Pharmacy's Fundamental Reference. Other articles were reviewed on the topics of counterfeiting, safe labeling, and implementation of unit-of-use packaging. Lastly, a cost-saving study was reviewed showing how medication adherence, due to improved packaging, could be cost-effective for patients. Results: When examining time, costs, medication adherence, and counterfeiting arguments, unit-of-use packaging proved to be beneficial for patients in all these terms.   Type: Student Project

Fresh meat packaging: consumer acceptance of modified atmosphere packaging including carbon monoxide.

Science.gov (United States)

Grebitus, Carola; Jensen, Helen H; Roosen, Jutta; Sebranek, Joseph G

2013-01-01

Consumers' perceptions and evaluations of meat quality attributes such as color and shelf life influence purchasing decisions, and these product attributes can be affected by the type of fresh meat packaging system. Modified atmosphere packaging (MAP) extends the shelf life of fresh meat and, with the inclusion of carbon monoxide (CO-MAP), achieves significant color stabilization. The objective of this study was to assess whether consumers would accept specific packaging technologies and what value consumers place on ground beef packaged under various atmospheres when their choices involved the attributes of color and shelf life. The study used nonhypothetical consumer choice experiments to determine the premiums that consumers are willing to pay for extended shelf life resulting from MAP and for the "cherry red" color in meat resulting from CO-MAP. The experimental design allowed determination of whether consumers would discount foods with MAP or CO-MAP when (i) they are given more detailed information about the technologies and (ii) they have different levels of individual knowledge and media exposure. The empirical analysis was conducted using multinomial logit models. Results indicate that consumers prefer an extension of shelf life as long as the applied technology is known and understood. Consumers had clear preferences for brighter (aerobic and CO) red color and were willing to pay $0.16/lb ($0.35/kg) for each level of change to the preferred color. More information on MAP for extending the shelf life and on CO-MAP for stabilizing color decreased consumers' willingness to pay. An increase in personal knowledge and media exposure influenced acceptance of CO-MAP negatively. The results provide quantitative measures of how packaging affects consumers' acceptance and willingness to pay for products. Such information can benefit food producers and retailers who make decisions about investing in new packaging methods.

Dossier: El catolicismo hispanoamericano en perspectiva atlántica. Redes, debates y actores de primera mitad del siglo XX. Hispano-American Catholicism from an Atlantic Perspective. Networks, Debates and Actors of First Half of the 20th Century

Directory of Open Access Journals (Sweden)

Miranda Lida

2017-10-01

Full Text Available El presente dossier procura bucear en una temática poco explorada: las redes transnacionales atlánticas que cementan y solidifican los movimientos católicos hispanoamericanos de la primera mitad del siglo XX. Cuando se habla del movimiento católico, es ineludible prestarle atención a los vínculos con la Santa Sede, naturalmente, pero suele ser escaso el cuidado que se le presta a otros vínculos transnacionales, ya sea con movimientos católicos europeos, norteamericanos, de diferentes países latinoamericanos o bien alguna combinación entre todos ellos.

16 CFR 503.6 - Packagers' duty to withhold availability of packages imprinted with retail sale price...

Science.gov (United States)

2010-01-01

... THE FAIR PACKAGING AND LABELING ACT STATEMENTS OF GENERAL POLICY OR INTERPRETATION § 503.6 Packagers... reason to know that it will be used as an instrumentality for deception or for frustration of value... fully passes on to the purchasers the represented savings or sale price advantage. (b) A packager or...

Analysis of Type A packaging systems based on greater than 400 individual packaging tests

International Nuclear Information System (INIS)

Edling, D.A.

1976-01-01

Type A packagings commonly used within the U.S. were studied to determine their performance with respect to, ''Tests for demonstrating ability to withstand normal conditions of transport,'' (e.g., water spray, free drop (4 ft), penetration, corner drop, and compression). There are several differences in U.S. and IAEA Type A packaging requirements and these are outlined. For purposes of this study, U. S. requirements were used. More than 100 separate packagings (greater than 400 individual tests) were studied and evaluated. Most of these packagings can be divided into four basic groups: steel drums, wooden boxes, fiberboard containers, and steel boxes. The steel drums met all the requirements with a minimum of qualification and restrictions on use. The wooden boxes performed well, with three-way corner construction providing the best results. The Type A performance requirements had a much greater effect on fiberboard packagings (boxes and drums). In most cases penetration of the fiberboard container did occur, but this was dependent on the inner packagings and materials used. Steel boxes offer a wide flexibility in types of construction, materials usable, volumes, and authorized gross weights. Material usage and construction for wooden and fiberboard containers, such as use of plywood in box construction, banding of boxes, and use of ''firm'' cushioning materials within fiberboard containers, are also discussed

Type B Drum packages

International Nuclear Information System (INIS)

Edwards, W.S.

1995-11-01

The Type B Drum package is a container in which a single drum containing Type B quantities of radioactive material will be packaged for shipment. The Type B Drum containers are being developed to fill a void in the packaging and transportation capabilities of the US Department of Energy (DOE), as no double containment packaging for single drums of Type B radioactive material is currently available. Several multiple-drum containers and shielded casks presently exist. However, the size and weight of these containers present multiple operational challenges for single-drum shipments. The Type B Drum containers will offer one unshielded version and, if needed, two shielded versions, and will provide for the option of either single or double containment. The primary users of the Type B Drum container will be any organization with a need to ship single drums of Type B radioactive material. Those users include laboratories, waste retrieval facilities, emergency response teams, and small facilities

49 CFR 173.23 - Previously authorized packaging.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Previously authorized packaging. 173.23 Section... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.23 Previously authorized packaging. (a) When the regulations specify a packaging with a specification marking...

Watermarking spot colors in packaging

Science.gov (United States)

Reed, Alastair; Filler, TomáÅ.¡; Falkenstern, Kristyn; Bai, Yang

2015-03-01

In January 2014, Digimarc announced Digimarc® Barcode for the packaging industry to improve the check-out efficiency and customer experience for retailers. Digimarc Barcode is a machine readable code that carries the same information as a traditional Universal Product Code (UPC) and is introduced by adding a robust digital watermark to the package design. It is imperceptible to the human eye but can be read by a modern barcode scanner at the Point of Sale (POS) station. Compared to a traditional linear barcode, Digimarc Barcode covers the whole package with minimal impact on the graphic design. This significantly improves the Items per Minute (IPM) metric, which retailers use to track the checkout efficiency since it closely relates to their profitability. Increasing IPM by a few percent could lead to potential savings of millions of dollars for retailers, giving them a strong incentive to add the Digimarc Barcode to their packages. Testing performed by Digimarc showed increases in IPM of at least 33% using the Digimarc Barcode, compared to using a traditional barcode. A method of watermarking print ready image data used in the commercial packaging industry is described. A significant proportion of packages are printed using spot colors, therefore spot colors needs to be supported by an embedder for Digimarc Barcode. Digimarc Barcode supports the PANTONE spot color system, which is commonly used in the packaging industry. The Digimarc Barcode embedder allows a user to insert the UPC code in an image while minimizing perceptibility to the Human Visual System (HVS). The Digimarc Barcode is inserted in the printing ink domain, using an Adobe Photoshop plug-in as the last step before printing. Since Photoshop is an industry standard widely used by pre-press shops in the packaging industry, a Digimarc Barcode can be easily inserted and proofed.

Hanford Site radioactive hazardous materials packaging directory

International Nuclear Information System (INIS)

McCarthy, T.L.

1995-12-01

The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations ampersand Development (PO ampersand D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage

Hanford Site radioactive hazardous materials packaging directory

Energy Technology Data Exchange (ETDEWEB)

McCarthy, T.L.

1995-12-01

The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations & Development (PO&D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage.

Packaging and Embedded Electronics for the Next Generation

Science.gov (United States)

Sampson, Michael J.

2010-01-01

This viewgraph presentation describes examples of electronic packaging that protects an electronic element from handling, contamination, shock, vibration and light penetration. The use of Hermetic and non-hermetic packaging is also discussed. The topics include: 1) What is Electronic Packaging? 2) Why Package Electronic Parts? 3) Evolution of Packaging; 4) General Packaging Discussion; 5) Advanced non-hermetic packages; 6) Discussion of Hermeticity; 7) The Class Y Concept and Possible Extensions; 8) Embedded Technologies; and 9) NEPP Activities.

Grandfathering of competent authority approved packages

International Nuclear Information System (INIS)

Osgood, N.L.

2004-01-01

International Atomic Energy Agency transportation regulations are reviewed and revised on a periodic basis as new technical and scientific information becomes available. The 1996 Edition of the Regulations for the Safe Transport of Radioactive Materials in TS-R-1 includes provisions for the use of package designs approved to previous editions of the regulations. This assures that there is no disruption of transport when the regulations are updated and revised. The revision of package design standards may make certain designs obsolete, though not necessarily unsafe. The U.S. Nuclear Regulatory Commission is the agency in the United States that certifies transportation packages for Type B and fissile materials. NRC regulations include grandfathering provisions that are comparable to and compatible with the IAEA standards. NRC staff is promoting a new system that would eliminate the need to grandfather package designs. Under the new method, any new or revised provision of the regulations that affects package standards would include its own transitional arrangements. In this way, each change would be evaluated for its safety importance. Changes in the package standards that are important to safety would be implemented immediately upon the regulations coming into force. Other changes, that do not significantly affect safety, would have longer implementation periods. In this way, all packages in use would be compatible with the regulations in force, and no specific grandfathering provisions for older designs would be needed. NRC staff has concluded that the package design standards are mature and have been shown to be protective over the past 40 years of shipping experience. We predict that future changes in package design standards will not be substantive in terms of resulting in significant changes in physical performance of a package in transport, including actual transportation accidents. The benefits of the new system would be a more predictable regulatory structure

Package testing capabilities at the Pacific Northwest Laboratory

International Nuclear Information System (INIS)

Taylor, J.M.

1993-01-01

The purpose of this paper is to describe the package testing capabilities at the Pacific Northwest Laboratory (PNL). In the past all of the package testing that was performed at PNL was done on prototype or mocked up radioactive material packaging. Presently, we are developing the capability to perform testing on non-radioactive material packaging. The testing on the non-radioactive material packaging will be done to satisfy the new performance oriented packaging requirements (DOT Docket HM-181, 1991). This paper describes the equipment used to perform the performance oriented packaging tests and also describes some testing capability for testing radioactive material packaging

RECENT TRENDS IN PACKAGING SYSTEMS FOR PHARMACEUTICAL PRODUCTS

Directory of Open Access Journals (Sweden)

Renata Dobrucka

2014-12-01

Full Text Available Background:  In recent years, pharmaceutical packaging market was one of the fastest growing areas of the packaging industry. At the same time the packaging manufacturers put high demands on quality and safety. Methods: Review of innovations in packaging systems for pharmaceutical products was made including newest information of researches and achievements of recent years. Results and conclusion: Observed in recent years the development of pharmaceutical packaging market expanded due to with the huge technological advances that allow introduction of new packaging. Also, in this study presented intelligent packaging in pharmacy and innovation in child-resistance packaging.

K Basin sludge packaging design criteria (PDC) and safety analysis report for packaging (SARP) approval plan

International Nuclear Information System (INIS)

Brisbin, S.A.

1996-01-01

This document delineates the plan for preparation, review, and approval of the Packaging Design Crieteria for the K Basin Sludge Transportation System and the Associated on-site Safety Analysis Report for Packaging. The transportation system addressed in the subject documents will be used to transport sludge from the K Basins using bulk packaging

The impact of packaging on product competition

Directory of Open Access Journals (Sweden)

Maryam Masoumi

2012-09-01

Full Text Available The primary objective of this paper is to detect important factors, which are influencing competitive advantage. The proposed model of this paper uses sampling technique to measure characteristics of society. There are eight independent variables for the proposed study of this paper including packaging endurance, easy distribution, customer promotion through packaging, packaging structure, packaging as silent advertiser, diversity of packaging, clean and healthy packaging and innovation in packaging. The proposed study uses structural equation modeling to either accept or reject all hypotheses associated with the proposed study of this paper. The population of this study includes all managers and experts who are involved in packaging products. We used simple sampling technique and chooses 300 from a population of 450 people who are considered as the population of this survey. Cronbach alpha was determined as 0.732, which is above the minimum acceptable level. The results confirm that all mentioned factors influence competitiveness, effectively.

Migration and sorption phenomena in packaged foods.

Science.gov (United States)

Gnanasekharan, V; Floros, J D

1997-10-01

Rapidly developing analytical capabilities and continuously evolving stringent regulations have made food/package interactions a subject of intense research. This article focuses on: (1) the migration of package components such as oligomers and monomers, processing aids, additives, and residual reactants in to packaged foods, and (2) sorption of food components such as flavors, lipids, and moisture into packages. Principles of diffusion and thermodynamics are utilized to describe the mathematics of migration and sorption. Mathematical models are developed from first principles, and their applicability is illustrated using numerical simulations and published data. Simulations indicate that available models are system (polymer-penetrant) specific. Furthermore, some models best describe the early stages of migration/sorption, whereas others should be used for the late stages of these phenomena. Migration- and/or sorption-related problems with respect to glass, metal, paper-based and polymeric packaging materials are discussed, and their importance is illustrated using published examples. The effects of migrating and absorbed components on food safety, quality, and the environment are presented for various foods and packaging materials. The impact of currently popular packaging techniques such as microwavable, ovenable, and retortable packaging on migration and sorption are discussed with examples. Analytical techniques for investigating migration and sorption phenomena in food packaging are critically reviewed, with special emphasis on the use and characteristics of food-simulating liquids (FSLs). Finally, domestic and international regulations concerning migration in packaged foods, and their impact on food packaging is briefly presented.

Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

Science.gov (United States)

Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

2012-11-01

The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. Copyright © 2012 Elsevier Ltd. All rights reserved.

Young people's perceptions of cigarette packaging and plain packaging: an online survey.

Science.gov (United States)

Moodie, Crawford; Ford, Allison; Mackintosh, Anne Marie; Hastings, Gerard

2012-01-01

In the United Kingdom, with most marketing channels prohibited, packaging is one of the few remaining ways that tobacco companies can promote their products. An online survey with young people aged 10-17 years (N = 658) was used to explore why youth choose cigarettes, perceptions of pack color, and perceptions of plain (nonbranded) cigarette packaging. Young people were also shown an image of 3 plain packs, which differed by shape and method of opening, and asked which they liked most and thought others their age would smoke. Price and what significant others smoke were key factors for choosing cigarettes, with packaging also an important influence. More than a third of the sample associated lighter pack color with weak tasting and less harmful cigarettes. Plain packs were rated negatively as were perceptions of plain pack users. One in 3 showed a preference for either a narrow "perfume type" plain pack or a plain "slide" pack that opened from the side, and 1 in 3 also thought that young people would smoke these packs. Packaging appears to both attract young people and mislead them about product strength and relative harm. Innovative pack construction (novel pack shape and method of opening) and the use of color are instrumental in these effects. The findings therefore suggest that any move to plain packaging should not only consider the benefits of removing branding (including color) but also of standardizing pack construction in terms of shape and method of opening.

Safety Analysis Report for Packaging (SARP): ATMX-500 Railcar nuclear packaging

International Nuclear Information System (INIS)

Griffin, J.F.; Peterson, J.B.; Edling, D.A.; Blauvelt, R.K.

1977-01-01

A Safety Analysis Report for Packaging (SARP) is described that makes available to all potential users the technical specifications and limits pertinent to the modification and use of the ATMX Railcars for which the Department of Transportation has issued Special Permit No. 5948. The SARP includes discussions of structural integrity, thermal resistance, radiation shielding and radiological safety, nuclear criticality safety, and quality control. Much of the information was previously published in a similar report. A complte physical and technical description of the package is presented. The packaging cnsists of a specially modified ATMX Series 500 Railcar loaded with DOT Specification steel drums or fiberglass coated plywood boxes. The results of the nuclear criticality safety analysis provide the maximum quantities of each fissile isotope which may be shipped as Fissile Class I in 30- and 55-gal drums. A limit of 5 g/ft 3 was established for wooden boxes. Design and development considerations regarding the packaging concept and modification of the ATMX-500 Railcar are presented. Tables, dimensional sketches, sequential photographs of the structural modifications, technical references, loading and shipping guidelines, and results of Mound Laboratory's experience in using this container are included. An internal review of this SARP was performed in compliance with the requirements of ERDA Manual Chapter 5201-Part V

7 CFR 58.151 - Packaging and repackaging.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Packaging and repackaging. 58.151 Section 58.151... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Packaging and General Identification § 58.151 Packaging and repackaging. (a) Packaging dairy products or cutting and repackaging all...

Dual Use Packaging, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NASA seeks down-weighted packaging compatible with microwave preparation and perhaps high hydrostatic pressure processing. New packaging must satisfy NASA's 3-year...

Safety analysis report: packages. DOT specification 7A - Type A container Mark 15 sludge shipping package

International Nuclear Information System (INIS)

Zeh, C.W.

1985-03-01

Sludge or filter cake containing 1.1 wt % 235 U enriched uranium from Mark 15 fabrication will be packaged in 55-gallon containers and shipped from SRP to NLO, Fernald, Ohio for recovery of product. About 7 Metric Tons (MT) of filter cake will be produced from fabricating Mark 15 slugs each reactor charge. Packaged shipments of this material, consigned as exclusive use, will be shipped to NLO in Department of Transportation (DOT) Specification 7A - Type A packages under a DOE Certificate of Compliance for Fissile Class III shipments. ''Type A packaging'' is designed to retain containment and shielding integrity under normal conditions of transport. This report documents compliance of the package design, construction methods, material and test performance with DOT Specification 7A. This DOT 7A Type A package contains a carbon steel outer container which is a 0.060-in.-thick 55-gal, galvanized drum equipped with a gasketed closure. The outer container encloses a 0.090-in.-thick, open head, polyethylene liner with lid

K east encapsulation packager modifications

International Nuclear Information System (INIS)

Jensen, M.A.

1994-01-01

This Supporting Document analyzes a proposal for reducing the under-packager volume to decrease the amount of fissile material that could accumulate there. The analysis shows that restricting the under packager volume to no more than 4080 in 3 will assure that if accumulated fissile material beneath the packager is added to the worst-case mass of fissile material in the discharge chute, a k eff of 0.98 will not be exceeded

System issues for multichip packaging

Science.gov (United States)

Sage, Maurice G.; Hartley, Neil

1991-04-01

It is now generally recognised that the performance of an electronic system is governed by the choice of packaging technology. Never before have the technical and financial implications of a packaging technology choice been more critical and never before has technology interdependence or industry globalisation made the choice more difficult. This paper is aimed at examining the choices available and the system issues resulting from the move from single chip to multichip packaging.

APPLICATION OF NANOTECHNOLOGY IN FOOD PACKAGING

Directory of Open Access Journals (Sweden)

Renata Dobrucka

2014-04-01

Full Text Available Nanotechnology involves the design, production and use of structures through control of the size and shape of the materials at the nanometre scale. Also, nanomaterials have been already applied in many fields of human life. Nanocomposites have already led to several innovations with potential applications in the food packaging sector. The use of nanocomposite formulations is expected to considerably enhance the shelf-life of many types of food. This improvement can lead to lower weight packages because less material is needed to obtain the same or even better barrier properties. This, in turn, can lead to reduced package cost with less packaging waste. Antimicrobial packaging is another area with high potential for applying nanocomposite technology. Nanostructured antimicrobials have a higher surface area-to-volume ratio when compared with their higher scale counterparts. Therefore, antimicrobial nanocomposite packaging systems are supposed to be particularly efficient in their activities against microbial cells. In this review, definition of nanomaterials is presented. Besides, the paper shows examples of nanocomposities and antimicrobial nanopackaging mainly with the use of nanosilver. Moreover, nanoparticles such ZnO, TiO2, MgO and nanosensors in packaging were presented.

Function Package for Computing Quantum Resource Measures

Science.gov (United States)

Huang, Zhiming

2018-05-01

In this paper, we present a function package for to calculate quantum resource measures and dynamics of open systems. Our package includes common operators and operator lists, frequently-used functions for computing quantum entanglement, quantum correlation, quantum coherence, quantum Fisher information and dynamics in noisy environments. We briefly explain the functions of the package and illustrate how to use the package with several typical examples. We expect that this package is a useful tool for future research and education.

Packaging and transportation manual. Chapter on the packaging and transportation of hazardous and radioactive waste

International Nuclear Information System (INIS)

1998-03-01

The purpose of this chapter is to outline the requirements that Los Alamos National Laboratory employees and contractors must follow when they package and ship hazardous and radioactive waste. This chapter is applied to on-site, intra-Laboratory, and off-site transportation of hazardous and radioactive waste. The chapter contains sections on definitions, responsibilities, written procedures, authorized packaging, quality assurance, documentation for waste shipments, loading and tiedown of waste shipments, on-site routing, packaging and transportation assessment and oversight program, nonconformance reporting, training of personnel, emergency response information, and incident and occurrence reporting. Appendices provide additional detail, references, and guidance on packaging for hazardous and radioactive waste, and guidance for the on-site transport of these wastes

Packaging and transportation manual. Chapter on the packaging and transportation of hazardous and radioactive waste

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this chapter is to outline the requirements that Los Alamos National Laboratory employees and contractors must follow when they package and ship hazardous and radioactive waste. This chapter is applied to on-site, intra-Laboratory, and off-site transportation of hazardous and radioactive waste. The chapter contains sections on definitions, responsibilities, written procedures, authorized packaging, quality assurance, documentation for waste shipments, loading and tiedown of waste shipments, on-site routing, packaging and transportation assessment and oversight program, nonconformance reporting, training of personnel, emergency response information, and incident and occurrence reporting. Appendices provide additional detail, references, and guidance on packaging for hazardous and radioactive waste, and guidance for the on-site transport of these wastes.

7 CFR 33.6 - Package.

Science.gov (United States)

2010-01-01

... the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... ISSUED UNDER AUTHORITY OF THE EXPORT APPLE ACT Definitions § 33.6 Package. Package means any container of apples. ...

7 CFR 58.444 - Packaging and repackaging.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Packaging and repackaging. 58.444 Section 58.444... Procedures § 58.444 Packaging and repackaging. (a) Packaging rindless cheese or cutting and repackaging all styles of bulk cheese shall be conducted under rigid sanitary conditions. The atmosphere of the packaging...

7 CFR 58.340 - Printing and packaging.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Printing and packaging. 58.340 Section 58.340... Procedures § 58.340 Printing and packaging. Printing and packaging of consumer size containers of butter... packaging equipment should be provided. The outside cartons should be removed from bulk butter in a room...

Waste Package Component Design Methodology Report

International Nuclear Information System (INIS)

D.C. Mecham

2004-01-01

This Executive Summary provides an overview of the methodology being used by the Yucca Mountain Project (YMP) to design waste packages and ancillary components. This summary information is intended for readers with general interest, but also provides technical readers a general framework surrounding a variety of technical details provided in the main body of the report. The purpose of this report is to document and ensure appropriate design methods are used in the design of waste packages and ancillary components (the drip shields and emplacement pallets). The methodology includes identification of necessary design inputs, justification of design assumptions, and use of appropriate analysis methods, and computational tools. This design work is subject to ''Quality Assurance Requirements and Description''. The document is primarily intended for internal use and technical guidance for a variety of design activities. It is recognized that a wide audience including project management, the U.S. Department of Energy (DOE), the U.S. Nuclear Regulatory Commission, and others are interested to various levels of detail in the design methods and therefore covers a wide range of topics at varying levels of detail. Due to the preliminary nature of the design, readers can expect to encounter varied levels of detail in the body of the report. It is expected that technical information used as input to design documents will be verified and taken from the latest versions of reference sources given herein. This revision of the methodology report has evolved with changes in the waste package, drip shield, and emplacement pallet designs over many years and may be further revised as the design is finalized. Different components and analyses are at different stages of development. Some parts of the report are detailed, while other less detailed parts are likely to undergo further refinement. The design methodology is intended to provide designs that satisfy the safety and operational

Waste Package Component Design Methodology Report

Energy Technology Data Exchange (ETDEWEB)

D.C. Mecham

2004-07-12

This Executive Summary provides an overview of the methodology being used by the Yucca Mountain Project (YMP) to design waste packages and ancillary components. This summary information is intended for readers with general interest, but also provides technical readers a general framework surrounding a variety of technical details provided in the main body of the report. The purpose of this report is to document and ensure appropriate design methods are used in the design of waste packages and ancillary components (the drip shields and emplacement pallets). The methodology includes identification of necessary design inputs, justification of design assumptions, and use of appropriate analysis methods, and computational tools. This design work is subject to ''Quality Assurance Requirements and Description''. The document is primarily intended for internal use and technical guidance for a variety of design activities. It is recognized that a wide audience including project management, the U.S. Department of Energy (DOE), the U.S. Nuclear Regulatory Commission, and others are interested to various levels of detail in the design methods and therefore covers a wide range of topics at varying levels of detail. Due to the preliminary nature of the design, readers can expect to encounter varied levels of detail in the body of the report. It is expected that technical information used as input to design documents will be verified and taken from the latest versions of reference sources given herein. This revision of the methodology report has evolved with changes in the waste package, drip shield, and emplacement pallet designs over many years and may be further revised as the design is finalized. Different components and analyses are at different stages of development. Some parts of the report are detailed, while other less detailed parts are likely to undergo further refinement. The design methodology is intended to provide designs that satisfy the safety

Directory of certificates of compliance for radioactive materials packages. Volume 1. Summary report of NRC approved packages

International Nuclear Information System (INIS)

1977-12-01

Purpose of this directory is to make available a convenient source of information on packagings which have been approved by the U.S. Nuclear Regulatory Commission. This volume contains a summary report of NRC-approved packages for radioactive material packages effective Nov. 30, 1977

Advanced organics for electronic substrates and packages

CERN Document Server

Fletcher, Andrew E

1992-01-01

Advanced Organics for Electronic Substrates and Packages provides information on packaging, which is one of the most technologically intensive activities in the electronics industry. The electronics packaging community has realized that while semiconductor devices continue to be improved upon for performance, cost, and reliability, it is the interconnection or packaging of these devices that will limit the performance of the systems. Technology must develop packaging for transistor chips, with high levels of performance and integration providing cooling, power, and interconnection, and yet pre

9 CFR 381.144 - Packaging materials.

Science.gov (United States)

2010-01-01

... to health. All packaging materials must be safe for the intended use within the meaning of section..., from the packaging supplier under whose brand name and firm name the material is marketed to the... distinguishing brand name or code designation appearing on the packaging material shipping container; must...

Grooming. Learning Activity Package.

Science.gov (United States)

Stark, Pamela

This learning activity package on grooming for health workers is one of a series of 12 titles developed for use in health occupations education programs. Materials in the package include objectives, a list of materials needed, information sheets, reviews (self evaluations) of portions of the content, and answers to reviews. These topics are…

Investigating the effect of aesthetic aspect of packaging and its dimensions on purchase intention through packaging preference

OpenAIRE

Abolghasem Ebrahimi; Sayed Moslem Alavi; Mehdi Najafi Seyahroodi

2015-01-01

Companies in the era of quality convergence of products are bound to differentiation. As a differentiating tool, Packaging can be a troubleshooter in this field. One of the ways of differentiation is to consider aesthetic aspect of packaging. According to this fact, current survey has studied the impact of aesthetic aspect of packaging on purchase intention of goods through packaging preference. A sample consisted of 384 customers of the big food stores in Shiraz is selected. To test the vali...

Waste package performance allocation system study report

International Nuclear Information System (INIS)

Memory, R.D.

1994-01-01

The Waste Package Performance Allocation system study was performed in order to provide a technical basis for the selection of the waste package period of substantially complete containment and its resultant contribution to the overall total system performance. This study began with a reference case based on the current Mined Geologic Disposal System (MGDS) baseline design and added a number of alternative designs. The waste package designs were selected from the designs being considered in detail during Advanced Conceptual Design (ACD). The waste packages considered were multi-barrier packages with a 0.95 cm Alloy 825 inner barrier and a 10, 20, or 45 cm thick carbon steel outer barrier. The waste package capacities varied from 6 to 12 to 21 Pressurized Water Reactor (PWR) fuel assemblies. The vertical borehole and in-drift emplacement modes were also considered, as were thermal loadings of 25, 57, and 114 kW/acre. The repository cost analysis indicated that the 21 PWR in-drift emplacement mode option with the 10 cm and 20 cm outer barrier thicknesses are the least expensive and that the 12 PWR in-drift case has approximately the same cost as the 6 PWR vertical borehole. It was also found that the cost increase from the 10 cm outer barrier waste package to the 20 cm waste package was less per centimeter than the increase from the 20 cm outer barrier waste package to the 45 cm outer barrier waste package. However, the repository cost was nearly linear with the outer barrier thickness for the 21 PWR in-drift case. Finally, corrosion rate estimates are provided and the relationship of repository cost versus waste package lifetime is discussed as is cumulative radionuclide release from the waste package and to the accessible environment for time periods of 10,000 years and 100,000 years