WorldWideScience

Sample records for bituminous macadam

  1. Research on differences and correlation between tensile, compression and flexural moduli of cement stabilized macadam

    Directory of Open Access Journals (Sweden)

    Yi Yang

    2017-07-01

    Full Text Available In order to reveal the differences and conversion relations between the tensile, compressive and flexural moduli of cement stabilized macadam, in this paper, we develop a new test method for measuring three moduli simultaneously. By using the materials testing system, we test three moduli of the cement stabilized macadam under different loading rates, propose a flexural modulus calculation formula which considers the shearing effect, reveal the change rules of the tensile, compression and flexural moduli with the loading rate and establish the conversion relationships between the three moduli. The results indicate that: three moduli become larger with the increase of the loading rate, showing a power function pattern; with the shear effect considered, the flexural modulus is increased by 47% approximately over that in the current test method; the tensile and compression moduli of cement stabilized macadam are significantly different. Therefore, if only the compression modulus is used as the structural design parameter of asphalt pavement, there will be a great deviation in the analysis of the load response. In order to achieve scientific design and calculation, the appropriate design parameters should be chosen based on the actual stress state at each point inside the pavement structure.

  2. Number of discernible colors for color-deficient observers estimated from the MacAdam limits.

    Science.gov (United States)

    Perales, Esther; Martínez-Verdú, Francisco Miguel; Linhares, João Manuel Maciel; Nascimento, Sérgio Miguel Cardoso

    2010-10-01

    We estimated the number of colors perceived by color normal and color-deficient observers when looking at the theoretic limits of object-color stimuli. These limits, the optimal color stimuli, were computed for a color normal observer and CIE standard illuminant D65, and the resultant colors were expressed in the CIELAB and DIN99d color spaces. The corresponding color volumes for abnormal color vision were computed using models simulating for normal trichromatic observers the appearance for dichromats and anomalous trichomats. The number of colors perceived in each case was then computed from the color volumes enclosed by the optimal colors also known as MacAdam limits. It was estimated that dichromats perceive less than 1% of the colors perceived by normal trichromats and that anomalous trichromats perceive 50%-60% for anomalies in the medium-wavelength-sensitive and 60%-70% for anomalies in the long-wavelength-sensitive cones. Complementary estimates obtained similarly for the spectral locus of monochromatic stimuli suggest less impairment for color-deficient observers, a fact that is explained by the two-dimensional nature of the locus.

  3. Cold bituminous mixes

    OpenAIRE

    Delak, Boštjan

    2012-01-01

    Asphalt mix (short also asphalt) can be obtained from nature (natural asphalt) or produced technically (artificial asphalt), i. e. as a mix of bituminous binder, stone grain, and other additives that improve the asphalt properties. The beginnings of the use of asphalt can be traced from 6,000 to 4,000 BC since people back then knew some materials that contained bitumen as a binder. A more frequent use of the natural asphalt, however, starts around 3,000 BC. Different peoples used it primar...

  4. Aqueous radioactive waste bituminization

    International Nuclear Information System (INIS)

    Williamson, A.S.

    1980-08-01

    The bituminzation of decontamination and ion exchange resin stripping wastes with four grades of asphalt was investigated to determine the effects of asphalt type on the properties of the final products. All waste forms deformed readily under light loads indicating they would flow if not restrained. It was observed in all cases that product leaching rates increased as the hardness of the asphalt used to treat the waste increased. If bituminization is adopted for any Ontario Hydro aqueous radioactive wastes they should be treated with soft asphalt to obtain optimum leaching resistance and mechanical stability during interim storage should be provided by a corrosion resistant container

  5. Nonlinearity of bituminous mixtures

    Science.gov (United States)

    Mangiafico, S.; Babadopulos, L. F. A. L.; Sauzéat, C.; Di Benedetto, H.

    2018-02-01

    This paper presents an experimental characterization of the strain dependency of the complex modulus of bituminous mixtures for strain amplitude levels lower than about 110 μm/m. A series of strain amplitude sweep tests are performed at different temperatures (8, 10, 12 and 14°C) and frequencies (0.3, 1, 3 and 10 Hz), during which complex modulus is monitored. For each combination of temperature and frequency, four maximum strain amplitudes are targeted (50, 75, 100 and 110 μm/m). For each of them, two series of 50 loading cycles are applied, respectively at decreasing and increasing strain amplitudes. Before each decreasing strain sweep and after each increasing strain sweep, 5 cycles are performed at constant maximum targeted strain amplitude. Experimental results show that the behavior of the studied material is strain dependent. The norm of the complex modulus decreases and phase angle increases with strain amplitude. Results are presented in Black and Cole-Cole plots, where characteristic directions of nonlinearity can be identified. Both the effects of nonlinearity in terms of the complex modulus variation and of the direction of nonlinearity in Black space seem to validate the time-temperature superposition principle with the same shift factors as for linear viscoelasticity. The comparison between results obtained during increasing and decreasing strain sweeps suggests the existence of another phenomenon occurring during cyclic loading, which appears to systematically induce a decrease of the norm of the complex modulus and an increase of the phase angle, regardless of the type of the strain sweep (increasing or decreasing).

  6. Bituminization of liquid radioactive waste. Part 3

    International Nuclear Information System (INIS)

    G'oshev, G.S.; Gradev, G.D.; Stefanova, I.G.; Milusheva, A.G.; Guteva, E.S.; Stefanov, G.I.

    1991-01-01

    The elaborated technology for bituminization of liquid radioactive wastes (salt concentrates) is characterized by the fact that the bituminization process takes place in two stages: concentration of the liquid residue and evaporation of the water with simultaneous homogeneous incorporation of the salts in the melted bitumen. An experimental installation for bituminization of salt concentrates was designed on the basis of this technology. The experience accumulated during the design and construction of the installation for bituminization of salt concentrates could be used for designing and constructing an industrial installation for bituminization of the liquid residue of the nuclear power plants. 2 tabs., 3 figs., 3 refs

  7. Economy of bituminous coal hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    von Hochstetter, H.

    1944-05-11

    The influence of various factors on the production cost of (Janina) bituminous coal hydrogenation is analyzed briefly. The initial reckoning yielded a production cost of 188 marks per metric ton of gasoline and middle oils. The savings concomitant to changes of one percent in gasification, one percent in utilization of purified coal, one percent raising of space/time yield, one percent increase in throughput, one percent in coal concentration in the paste, and one percent in low temperature carbonization yield are listed. Factors affecting hydrogen consumption are listed in a table. Investigations showed the carbon-richest coal to produce a deviation in the effect of gasification upon the working costs by only 10 percent when compared with the Janina coal. Thus, the values listed were considered as guidelines for all kinds of bituminous coal. The calculations admitted the following conclusions: a maximum concentration of coal in the paste is desirable; one can assume a 2 percent reduction in the utilization with a 10 percent increase in throughput, as long as no changes in low temperature carbonization yield take place by changing the distribution in oil production; this configuration would change if the major concern were gas production instead of working costs, or if hydrogen production were the bottleneck. 1 table.

  8. 30 CFR 716.4 - Special bituminous coal mines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Special bituminous coal mines. 716.4 Section... INTERIOR INITIAL PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.4 Special bituminous coal mines. (a) Definition. Special bituminous coal surface mines as used in this section means those bituminous...

  9. Leachability of bituminized radioactive waste. Literature survey

    International Nuclear Information System (INIS)

    Akimoto, Toshiyuki; Nakayama, Shinichi; Iida, Yoshihisa; Nagano, Tetsushi

    1999-02-01

    Bituminized radioactive waste that will be returned from COGEMA, France is planned to be disposed of in deep geologic repository in Japan. Data on leachability of radionuclides from bituminized waste are required for the performance assessment of the disposal. We made a literature survey on bitumen and bituminized radioactive waste, placing emphasis on leach tests and leach data in terms of geologic disposal. This survey revealed that reliable leach data on transuranium elements and data obtained under reducing conditions that is characteristic to deep underground are lacking. (author). 64 refs

  10. Cold weather paving requirements for bituminous concrete.

    Science.gov (United States)

    1973-01-01

    Cold weather paving specifications were developed from work by Corlew and Dickson, who used a computer solution to predict the cooling rate of bituminous concrete. Virginia had used a minimum atmospheric temperature as a criterion; however, it was ev...

  11. Development of bituminization process for radioactive wastes

    International Nuclear Information System (INIS)

    Segawa, Takeshi; Yamamoto, Masao; Miyao, Hidehiko; Mizuno, Ryukichi

    1973-01-01

    For the bituminization of radioactive wastes from a fuel reprocessing plant, the leachability, irradiation stability and burning property of bitumen products have been studied. Sodium nitrate was used for simulated evaporator concentrate, and mixed with distillation bitumen or blown bitumen; the sodium nitrate content in the mixture was 30 to 60 wt%. The distillation bitumen is superior to the blown bitumen in leachability and flash point, but inferior in the increase of volume by irradiation. Since the volume increase is not large, the distillation bitumen is satisfactory for the bituminization of the evaporator concentrate from a fuel reprocessing plant. (Mori, K.)

  12. Crumb Rubber in cold recycled bituminous mixes

    DEFF Research Database (Denmark)

    Dondi, Giulio; Tataranni, Piergiorgio; Pettinari, Matteo

    2014-01-01

    Today recycling is one of the most innovative and interesting techniques for the rehabilitation of destressed road pavements. In recent years the increased interest in this process, has led to the development of various alternative methods for the recovery and the reuse of road bituminous materials....... Cold recycling is, among the recycling techniques, certainly the most studied and developed: it allows the recovering of bituminous material from an existing pavement without the addition of heat, whilst ensuring the creation of high quality bound base layers. A wide range of materials have been tested...

  13. Firing a sub-bituminous coal in pulverized coal boilers configured for bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    N. Spitz; R. Saveliev; M. Perelman; E. Korytni; B. Chudnovsky; A. Talanker; E. Bar-Ziv [Ben-Gurion University of the Negev, Beer-Sheva (Israel)

    2008-07-15

    It is important to adapt utility boilers to sub-bituminous coals to take advantage of their environmental benefits while limiting operation risks. We discuss the performance impact that Adaro, an Indonesian sub-bituminous coal with high moisture content, has on opposite-wall and tangentially-fired utility boilers which were designed for bituminous coals. Numerical simulations were made with GLACIER, a computational-fluid-dynamic code, to depict combustion behavior. The predictions were verified with full-scale test results. For analysis of the operational parameters for firing Adaro coal in both boilers, we used EXPERT system, an on-line supervision system developed by Israel Electric Corporation. It was concluded that firing Adaro coal, compared to a typical bituminous coal, lowers NOx and SO{sub 2} emissions, lowers LOI content and improves fouling behavior but can cause load limitation which impacts flexible operation. 21 refs., 7 figs., 3 tabs.

  14. Radioactive wastes bituminization by the pilot-plant equipment

    International Nuclear Information System (INIS)

    Golinsky, M.; Ferenc, M.; Ksendzak, Z.; Tikal, A.

    1978-01-01

    Operation experience of pilot-plant for bituminization of radioactive wastes by the method of hot mixing is described. The results obtained have conffirmed parameters of the process gained in laboratory conditions for asphalts D-35 and P-60. The results are stated for experiments of bituminization of still residuums obtained as a result of distillation of low and intermediate-level of activity sewage waters. Chemical composition of the still residuums and characteristics of the P-60 asphalt are given. Bituminization of crystal sodium nitrate and supersaturated solutions at 200 centigrades up to 30% contents of salt in the compound was performed. It is shown that bituminization results depend on salts composition of radioactive wastes subject to solidification. The results are described of investigations of bituminization by the method of hot mixing of still residuums of radioactive wastes containing sodium nitrates on the pilot-plant. Parameters are given of bituminization process and characteristics of compounds obtained in bituminization of still residuums in a form of concentrates. Leachind process for wastes solidificated by the method of bituminization has been investigated. Leaching rate for radionuclides incorporated into bituminization products depending on time of storage is given. Results of the spectrometric analysis of solidificated concentrates, bituminization product and gaseous products of radioactive wastes processing by the method of hot mixing are given. (I.T.) [ru

  15. Behaviour of bituminized radioactive wastes under irradiation

    International Nuclear Information System (INIS)

    Camaro, S.; Gilardi, T.; Vistoli, P.P.

    2000-01-01

    Studies are carried out by the CEA in order to predict the behaviour of bituminized radioactive wastes under self irradiation. Bitumen radiolysis produces gas (mainly H 2 ) which diffuses in the organic matrix. If the hydrogen yield is higher than the diffusion flux through the free surface, hydrogen concentration increases and exceeds its solubility in bitumen. Beyond saturation, bubbles are formed and gas is also evacuated by bubbles drift. The aim of these studies is to evaluate the evacuation capacity of radiolytic gas produced in function of initial bituminized wasteform characteristics. A model was developed to achieve this purpose, by calculating the evolution of bubbles population considering all elementary mechanisms of gas evacuation. (authors)

  16. Bituminization of liquid radioactive wastes. Part 1

    International Nuclear Information System (INIS)

    Gradev, G.D.; Ivanov, V.I.; Stefanova, I.G.; Milusheva, A.G.; Guteva, E.S.; Zhelyazkov, V.T.; Stefanov, G.I.; G'oshev, G.S.

    1991-01-01

    Salt-bitumen products are produced by the method of 'hot mixing' of some Bulgarian bitumens (road bitumen PB 66/99 and the hydroinsulating bitumen HB 80/25) and salts (chlorides, sulphates, borates, salt mixtures modelling the liquid waste from nuclear power plants) in different ratios to determine the optimum conditions for bituminization of liquid radioactive waste. The penetration, ductility and softening temperature were determined. The sedimentation properties and the thermal resistance of the various bitumen-salt mixtures were studied. The most suitable bitumen for technological research at the Kozloduy NPP was found to be the road bitumen PB 66/90 with softening temperature at 48 o C. The optimum amount of salts incorporated in the bitumen - about 45% - was found. No exothermal effects were observed in the bituminization process in the temperature range of up to 200 o C. The results obtained may be useful in the elaboration of a technology for bituminization of liquid radioactive wastes in the Kozloduy NPP. 4 tabs., 5 figs., 4 refs

  17. Bituminization of low- and medium-level radioactive wastes

    International Nuclear Information System (INIS)

    Lefillatre, G.

    1976-01-01

    French operations are presented concerning mainly: the bituminization of radioactive wastes produced in light water reactors; the direct bituminization of liquid effluents without concentration; the experiments carried out for 18 months on the land burial of concentrates solidified by bitumen into blocks of 100 liters. The knowledge acquired in France is exposed: in Valduc and in Saclay with facilities equipped with thin film evaporators and in Marcoule with the conditioning of trilaurylamine and tributyl-phosphate. At last the Cadarache bituminization [fr

  18. Pretreatment of bituminous coal for hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer, H.

    1943-03-29

    Bituminous coal became plastic at certain temperature ranges and swelled, causing plugging of preheater tubes. With few exceptions, this problem was encountered only when hydrogenating bituminous coal. This swelling often appeared in the coking of coals, and for the majority of the cases it was found that efforts to reduce the baking ability of bituminous coal also reduced the swelling of coal paste in the preheater tubes. Three methods of pretreatment to reduce swelling were preheating, oxidation (anoxidation), and sulfur treatment. The preheating by hot nitrogen at 250 atm for 3 hours showed no improvement in swelling characteristics, but produced a greater asphalt content and a lower amount of gasification. Absorption of oxygen was shown to increase the viscosity of the coal paste, while preheating in a vacuum showed no effects. Oxidation (anoxidation) increased the splitting and gasification and gave higher asphalt content. The baking ability of Saar coal could be destroyed by addition of 2.5% sulfur and heating for 1/sup 1///sub 2/ hours at 110/sup 0/C, in a stream of H/sub 2/S. The volatile content dropped significantly when the same coal was heated to 200/sup 0/ to 250/sup 0/C. When neutralized Saar coal was dried under a stream of H/sub 2/S, only slight deterioration of the yield was noted with equal degree of gasification. It was concluded that a more or less distinct improvement would be observed from the absorption of sulfur, but that residue processing would have to be altered to account for the sulfur content.

  19. Bituminization of radioactive wastes at the Nuclear Research Center Karlsruhe

    International Nuclear Information System (INIS)

    Hild, W.; Kluger, W.; Krause, H.

    1976-05-01

    A summary is given of the main operational experience gained at the Nuclear Research Center Karlsruhe in 4 years operation of the bituminization plant for evaporator concentrates from low- and medium level wastes. At the same time some of the essential results are compiled that have been obtained in the R + D activities on bituminization. (orig.) [de

  20. Response Modelling of Bitumen, Bituminous Mastic and Mortar

    NARCIS (Netherlands)

    Woldekidan, M.F.

    2011-01-01

    This research focuses on testing and modelling the viscoelastic response of bituminous binders. The main goal is to find an appropriate response model for bituminous binders. The desired model should allow implementation into numerical environments such as ABAQUS. On the basis of such numerical

  1. Simple volatility test for bituminous materials

    Energy Technology Data Exchange (ETDEWEB)

    Sharp, J.A.

    1980-04-01

    A simple, inexpensive test measuring the volatility or fuming propensity of bituminous materials with good repeatability has been devised. The test depends on measuring the mass loss which occurs when a small sample of the material is heated in a shallow open dish on a thermostatic hotplate for a fixed time. A rectilinear inverse relation between the mass losses and the softening points of a series of pitches from one source has been found, and the test has been shown to give results which correlate well with other methods for characterizing pitch volatility. Test results obtained with a range of tar products from pitches to creosotes all showed similarly good repeatability. (4 refs.)

  2. Rutting performance of cold bituminous emulsion mixtures

    Science.gov (United States)

    Arshad, Ahmad Kamil; Ali, Noor Azilatom; Shaffie, Ekarizan; Hashim, Wardati; Rahman, Zanariah Abd

    2017-10-01

    Cold Bituminous Emulsion Mixture (CBEM) is an environmentally friendly alternative to hot mix asphalt (HMA) for road surfacing, due to its low energy requirements. However, CBEM has generally been perceived to be less superior in performance, compared to HMA. This paper details a laboratory study on the rutting performance of CBEM. The main objective of this study is to determine the Marshall properties of CBEM and to evaluate the rutting performance. The effect of cement in CBEM was also evaluated in this study. The specimens were prepared using Marshall Mix Design Method and rutting performance was evaluated using the Asphalt Pavement Analyzer (APA). Marshall Properties were analysed to confirm compliance with the PWD Malaysia's specification requirements. The rutting performance for specimens with cement was also found to perform better than specimens without cement. It can be concluded that Cold Bituminous Emulsion Mixtures (CBEM) with cement is a viable alternative to Hot Mix Asphalt (HMA) as their Marshall Properties and performance obtained from this study meets the requirements of the specifications. It is recommended that further study be conducted on CBEM for other performance criteria such as moisture susceptibility and fatigue.

  3. Processing of bituminous coal tar at high temperature with bituminous coal additive

    Energy Technology Data Exchange (ETDEWEB)

    von Hartmann, G.B.; Hupfer, H.; Leonhardt, P.

    1943-05-10

    In short tests, results of the effects of a bituminous coal addition to the processing of tar and pitch were obtainable. Coal used was that from the Heinitz Mines (Upper Silesian), saturated with 1--1.2% iron sulphate. On a mixture of bituminous coal tar residue and tar oil, with a relatively low level of solids and asphalt, a substitution was made for the addition of 2% alkalized iron-grude-catalyst with 20% coal. The same yield was reached using a straight-run procedure. The coal gave somewhat more gasification and additional asphalt in the sludge without increasing the solids content correspondingly. In spite of this, the carbonization results were somewhat improved, which led one to conclude that the coal addition fostered the decomposition of the tar asphalt, and, that the asphalt from the coal could be better carbonized than that out of the tar. One found, also, that the tar mixture with coal additive permitted trouble-free hydrogenation to gasoline and middle oil. Still another short test met with success. A bituminous coal tar pitch containing 24% benzene solids and 36% asphalt, which could not be processed with iron catalyst or even molybdenum-grude, was hydrogenated to gasoline and middle oil with a usable yield of .25 by a 20--25% addition of coal. Here too, the carbonization results were good. The addition of coal had no notable influence on the properties of the resulting oils. The document included test procedures. 11 tables.

  4. Bituminization of radioactive wastes: safety problems and application fields

    International Nuclear Information System (INIS)

    Lefillatre, G.; Leconnetable, J.

    1975-01-01

    The bituminization of low and medium radioactive wastes has many advantages: volume and weight reduction; homogeneity of the solid obtained; good resistance to leaching (biological resistance to microorganisms, resistance to radiations); very favorable characteristics for transport and storage. The latest bituminization facility put into service at the CEA is that of the Saclay Center. The bituminization unit is located after a primary evaporator having a distillation capacity of 2m 3 /h. It enables the coating of effluents at the rate of 60l/h [fr

  5. Skid resistance of bituminous surfaces in Ohio

    Science.gov (United States)

    Colony, D. C.

    1984-03-01

    Statistical studies of skid number (SN) on the state highway system in Ohio reveal apparently systematic variations in distributions of SN among the twelve districts in the state. These variations appear to be significantly related to traffic and to geological characteristics of a given district. Regression calculations using traffic index, a function of ADT and age of the pavement surface in months, show a high correlation with SN, although standard errors of estimate were too large to make the equations useful for predicting SN from traffic variables. Similar results were obtained by elating SN to physiographic features in the state. Pavement surface type (bituminous or pcc) and coarse aggregate type (limestone, gravel or slag) are significantly related to SN.

  6. Effect of antistripping additives on the compaction of bituminous concrete.

    Science.gov (United States)

    1981-01-01

    The objective of this investigation was to determine the effect of antistripping additives on the compaction of bituminous concrete. To do this, the densities obtained on test sections with and without additive were compared. Comparisons of nuclear d...

  7. Long-term properties of bituminized waste products

    International Nuclear Information System (INIS)

    Snellman, M.; Valkiainen, M.

    1985-10-01

    This study is a survey of the factors of importance for long term behaviour of bituminized ion exchange resins. Phenomena occurring in bituminized waste products affected by the treatment, storage and disposal are identified. Test methods have been developed for characterizing product properties, which are important for the long-term behaviour. The long-term properties of bituminized ion-exchange resins are studied in a repository environment with access of water equilibrated with concrete. In these circumstances the most important properties are ralated to the interactions of bituminized waste with the surrounding barriers. The most important phenomena are water uptake due to rehydration of the resins and subsequent swelling of the product. (author)

  8. Long-term properties of bituminized waste products

    International Nuclear Information System (INIS)

    Snellman, M.; Valkiainen, M.

    1985-10-01

    This study is a survey of the factors of importance for the long term behaviour of bituminized ion exchange resins. Phenomena occurring in bituminized waste products affected by the treatment, storage and disposal are identified. Test methods have been developed for characterizing product properties, which are important for the long-term behaviour. The long-term properties of bituminized ion-exchange resins are studied in a repository environment with access of water equilibrated with concrete. In these circumstances the most important properties are related to the interactions of bituminized waste with the surrounding barriers. The most important phenomena are water uptake due to rehydration of the resins and subsequent swelling of the product

  9. Design of bituminous surface mixes with high skid resistance.

    Science.gov (United States)

    1974-01-01

    The Virginia Highway Research Council has proposed a study of the skid resistance of bituminous surfaces incorporating relatively hard and expensive aggregates. The hardness of the aggregates to be used aluminum oxide (Exolon) and calcined kaolin -- ...

  10. Design of bituminous mixes with high skid resistance.

    Science.gov (United States)

    1979-01-01

    Certain highway locations need exceptionally high skid resistance because of the alignment, geometry, and drainage of the roadway and the complex turning maneuvers required. Several beam specimens made of bituminous mixes incorporating unconventional...

  11. Bituminous and asphaltic membranes for radioactive waste repositories on land

    International Nuclear Information System (INIS)

    1988-03-01

    The aim of the study has been to identify, within generic designs for waste facilities, areas where bituminous materials might be incorporated as a barrier. The report is presented in three sections: Part I - The properties of bitumen are described, with particular reference to the long-term behaviour of the material. The durability of bitumen is discussed, including aspects such as ageing, microbial degradation, chemical resistance and radiation resistance. Part II -The use of bituminous materials in hydraulic engineering is outlined. Much of this section of the report concentrates on the use of bituminous materials in embankment dams and reservoir construction. A review of material technology and construction techniques is presented and a detailed assessment made of the performance of the materials in service. Part III - Generic trench type radioactive waste repository designs incorporating bituminous materials are presented. Material and construction specifications for the designs are detailed, and a performance assessment presented. (author)

  12. Measurement of heat generation from simulated bituminized product

    Energy Technology Data Exchange (ETDEWEB)

    Kato, Yoshiyuki; Yoneya, Masayuki [TRP Safety Evaluation and Analysis team, Japan Nuclear Cycle Development Inst., Tokai, Ibaraki (Japan)

    1999-09-01

    The fire and explosion incident occurred at Bituminization Demonstration Facility of PNC Tokai Works on March 11, 1997. In order to ascertain the cause of incident, the investigation has been pushed forward. For the investigation, we prepared simulated bituminized product of measurement of heat generation in low temperature region less than 200degC. We used calvet Calorimeter MS80 for the heat generation measurement. Result of measurement, we were able to catch the feeble heat generation from bituminized product. The maximum calorific value that was able to detect it in isothermal measurement was approximately 1 mW/g in 160degC. It was approximately 2 mW/g in 200degC. And, as the another measurement, the measurement condition went heat rate by 0.01degC/minute, the highest temperature 190degC. As a result, the maximum generation of heat value that was able to detect it was approximately 0.5 mW/g. I changed simulated bituminized products and measured these. A difference of condition is salt particle size, salt content rate (45%, 60%), addition of the simulated precipitate. But there was not a difference in the generation of heat characteristic detected. (author)

  13. Reuse of steel slag in bituminous paving mixtures.

    Science.gov (United States)

    Sorlini, Sabrina; Sanzeni, Alex; Rondi, Luca

    2012-03-30

    This paper presents a comprehensive study to evaluate the mechanical properties and environmental suitability of electric arc furnace (EAF) steel slag in bituminous paving mixtures. A variety of tests were executed on samples of EAF slag to characterize the physical, geometrical, mechanical and chemical properties as required by UNI EN specifications, focusing additionally on the volumetric expansion associated with hydration of free CaO and MgO. Five bituminous mixtures of aggregates for flexible road pavement were designed containing up to 40% of EAF slag and were tested to determine Marshall stability and indirect tensile strength. The leaching behaviour of slag samples and bituminous mixtures was evaluated according to the UNI EN leaching test. The tested slag showed satisfactory physical and mechanical properties and a release of pollutants generally below the limits set by the Italian code. Tests on volume stability of fresh materials confirmed that a period of 2-3 months is necessary to reduce effects of oxides hydration. The results of tests performed on bituminous mixtures with EAF slag were comparable with the performance of mixtures containing natural aggregates and the leaching tests provided satisfactory results. Copyright © 2012 Elsevier B.V. All rights reserved.

  14. Properties of bituminization product from Olkiluoto power plant

    International Nuclear Information System (INIS)

    Valkiainen, M.; Vuorinen, U.

    1985-09-01

    In Finland, disposal into repositories excavated into bedrock on the present power plant sites is considered to be the most feasible alternative for the low- and intermediate level wastes. The Nuclear Waste Commission of the Finnish power companies has sponsored mainly experimental research work on long-term properties of bituminized ion exchange resin performed in the Reactor Laboratory of the Technical Research Centre of Finland since 1981. This report presents results on follow-up measurements of the leach tests started in 1981 and results on new leach tests with cement equilibrated water. Swelling of the bituminization product caused by water uptake is considered important. Both unrestricted and restricted swelling measurements were performed and are reported here. In addition to leaching and swelling also radiolytic gas generation and pH-changes of the leachant are discussed

  15. Pulp and paper plant wastes valorisation in bituminous mixes.

    Science.gov (United States)

    Modolo, R; Benta, A; Ferreira, V M; Machado, L M

    2010-04-01

    Nowadays, the increasing amount of wastes is a concerning reality and the environmental aspects has become a major priority. Following this worry, the purpose of this experimental study was to investigate the possibility of using pulp and paper inorganic wastes, named dregs and grits, in bituminous mixtures as aggregate replacement to reduce environmental effects of these wastes disposal. First, the wastes were chemically and physically characterized and also tested primarily taking into account the requirements for aggregates in bituminous mixtures. Then, formulations were prepared replacing aggregates with wastes in different amounts. The mechanical properties of these mixtures containing wastes were compared with reference samples based on standard methods. According to the results it was possible to verify that grits had a good performance and it might be directly tested industrially as an aggregate in road construction. On the other hand, dregs need to be treated before incorporation to guarantee stable mixes in terms of water sensitivity. Copyright 2009 Elsevier Ltd. All rights reserved.

  16. Solidification of radioactive wastes by bituminization technology. II

    International Nuclear Information System (INIS)

    Stuchlik, S.; Brzobohaty, J.

    1985-01-01

    The bituminization line consists of a rotor film evaporator, a condenser, reserve tanks of bitumen emulsion and model concentrates, a roller train, a vapour concentrate tank, a control console, a bitumen emulsion pump, a model concentrates pump, and a tank for model concentrate preparation. Anion-active emulsion Silembit S-60 produced by Paramo Pardubice was chosen as the bitumen emulsion. A block diagram is given of the experimental bituminization line and its processing is described of model nonactive concentrates whose composition corresponds to that of actual wastes from the V-1 nuclear power plant. Successful tests of the line showed that it could be used for the disposal of radioactive wastes. (E.S.)

  17. Comparison of the performances of several modified bituminous mix formulas

    Science.gov (United States)

    Saoula, Samia; Haddadi, Smail; Mokhtar, Khedidja Ait

    2012-09-01

    The mechanical behaviour of several formulas of bituminous concrete containing polymer (HDPE), polymer-bitumens (EVA) and waste of sole of shoes (containing copolymer butadiene-styrene-SBR noted DSBR and ethylene and vinyl acetate-EVA noted DEVA) were studied. The aim of this work is to improvement of the poor mechanicals performances of a bituminous concrete formula (0/14) which isn't conforming to the Algerian standards. Also, the mechanical tests showed that the permanent deformations and the indirect tensile strength at the temperatures of service resistances are improved. At high-temperature service, formulas of asphalt bitumen-EVA most resistant against the average temperature in service, it mixes made with waste are best resistant. All the formulas have a good behaviour with water.

  18. Nigerian bituminous coal as a fuel-coal. | OGUGBUAJA | Global ...

    African Journals Online (AJOL)

    Nigerian bituminous coal as a fuel-coal. V O OGUGBUAJA, C L NDIOKWERE, G A DIMARI. http://dx.doi.org/10.4314/gjpas.v6i2.16113 · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL ...

  19. Identification of aggregates for Tennessee bituminous surface courses

    Science.gov (United States)

    Sauter, Heather Jean

    Tennessee road construction is a major venue for federal and state spending. Tax dollars each year go to the maintenance and construction of roads. One aspect of highway construction that affects the public is the safety of its state roads. There are many factors that affect the safety of a given road. One factor that was focused on in this research was the polish resistance capabilities of aggregates. Several pre-evaluation methods have been used in the laboratory to predict what will happen in a field situation. A new pre-evaluation method was invented that utilized AASHTO T 304 procedure upscaled to accommodate surface bituminous aggregates. This new method, called the Tennessee Terminal Textural Condition Method (T3CM), was approved by Tennessee Department of Transportation to be used as a pre-evaluation method on bituminous surface courses. It was proven to be operator insensitive, repeatable, and an accurate indication of particle shape and texture. Further research was needed to correlate pre-evaluation methods to the current field method, ASTM E 274-85 Locked Wheel Skid Trailer. In this research, twenty-five in-place bituminous projects and eight source evaluations were investigated. The information gathered would further validate the T3CM and find the pre-evaluation method that best predicted the field method. In addition, new sources of aggregates for bituminous surface courses were revealed. The results of this research have shown T3CM to be highly repeatable with an overall coefficient of variation of 0.26% for an eight sample repeatability test. It was the best correlated pre-evaluation method with the locked wheel skid trailer method giving an R2 value of 0.3946 and a Pearson coefficient of 0.710. Being able to predict field performance of aggregates prior to construction is a powerful tool capable of saving time, money, labor, and possibly lives.

  20. Gamma radiation hazard to miners in bituminous coal mines

    International Nuclear Information System (INIS)

    Skubacz, K.

    1986-01-01

    Radiation hazard to miners working in 16 bituminous coal mines was determined by a thermoluminescence method. While the miners exposure to gamma radiation is higher than that of the general population, the yearly dose was never found to exceed 5 mSv in any investigated person. Factors contributing to the estimate of the exposure hazard and the need for individual dose monitoring in mines are discussed in more detail. 3 refs., 4 figs. (author)

  1. An experimental evaluation of coke production from bituminous coal tar

    Energy Technology Data Exchange (ETDEWEB)

    Kaloc, M.; Janik, M.; Rojak, A.

    1981-01-01

    Results of studies of laboratory coking of bituminous coal tar are presented, which verify the technical feasibility and suitability of this engineering process for coke production. Thanks to the closed-system character of the process, it is suitable for technological and hygienic reasons. The yield of pitch coke is higher by comparison with that from chamber coking; also the properties of this coke are better; it is suitable for more varied applications, including the production of large-diameter graphite electrodes.

  2. Biodegradation of bituminous products from processing liquid radioactive wastes

    International Nuclear Information System (INIS)

    Tibensky, L.; Krejci, F.; Hladky, E.; Halama, D.

    1988-01-01

    One of the possible ways of disturbing the stability of bituminous products from liquid radioactive waste processing, is biodegradation caused by common microorganisms. Pseudomonas bacteria and a Bacillus cereus culture were selected for experimental study of cultivation of microorganisms. Experiments with mixed cultures were also performed. Pitches, ajatin and imidazoline were used as inhibitors. The thin layer and the emulsion methods were used in assessing biological corrosion. The results of the experiments are discussed with respect to the dependence of bacterial growth on bitumen biodegradation, the effect of pH on bitumen degradation and the effect of inhibitors on bitumen biodegradation. The salts contained in bituminous products were not found to significantly affect the rate of destruction. The degree of degradation was found to mainly depend on the bitumen, its chemical composition, and on the conditions of storage. It was also found that inhibitor additions in some cases modified the properties of the matrix such that it became more liquid. The coefficient of extractibility thus increased of matrix salts. The recultivation of bacteria on a full-value medium resulted in the loss of the inhibitory effect. In some cases, the inhibitor even stimulated the growth of microorganisms. The use of inhibitors in an effort to achieve biostability of bituminous products thus did not solve the problem. (Z.M.). 2 tabs., 9 refs

  3. Wetting of bituminized ion-exchangers under simulated repository conditions

    International Nuclear Information System (INIS)

    Aalto, H.; Valkiainen, M.

    2001-01-01

    According to the present plans the spent nuclear fuel from four Finnish nuclear power units will be transferred after interim storage to the final disposal site where it will be encapsulated and disposed of in a final repository constructed into the bedrock at a depth of 500 meters. Low and medium level waste generated at nuclear power plants will be finally disposed of in caverns constructed in the bedrock at the power plant site. The safety of the final disposal is based on a multibarrier concept and the degree of safety is estimated by using predictive models. The properties of the waste form are taken into account in the design of the repository construction. Bitumen has been chosen as an immobilisation agent for the wet wastes at Olkiluoto Power Plant, where two BWR units, TVO 1 and TVO 2, have separate bituminization facilities designed by Asea-Atom. Properties of bituminized spent ion-exchange resins from Olkiluoto power plant have been studied by VTT Chemical Technology since the late 70's. These studies have concentrated mainly on determining the long-term behaviour of the bituminization product under the repository conditions. Current interest lies on wetted product as a diffusion barrier. For this purpose a microscopic method for the visualisation of the structure of the wetted product has been developed. The equilibration of the samples in simulated concrete groundwater is currently going on at a temperature of 5-8 deg. C. Preliminary results are presented in this paper. Diffusion experiments have been planned for the further characterising of the wetted product as a release barrier for radionuclides including modelling. (author)

  4. Low NOx firing systems for bituminous coal and lignite

    International Nuclear Information System (INIS)

    Knyrim, W.; Scheffknecht, G.

    1997-01-01

    In the case of lignite fluidized boilers the denitrification down to less than 200 mg/m 3 was possible with primary measures on the firing side only. On account of the excellent results achieved with the reconstructed plants the firing systems for the new generation of brown coal fire steam generators with a capacity of 800 MW and more is designed in a similar way. For bituminous coal fire steam generators the primary measures on the firing side are nor sufficient to keep the German NO x emission limit. Therefore these units had to be retrofitted with a SCR-DENOX plant. The experience with the new firing system made in a 110 MW steam generator in Austria with a wide range of fuels is introduced. One of the largest bituminous coal fired once-trough steam generator built by EVT is the boiler for the power station Bexbach I (750 MW). The firing system is designed as a tangential firing system with 32 jet burners. These are arranged in pairs in the corners and divided into 4 burner levels with 4 burner pairs each. One mill is allocated to each burner level. An important characteristic feature is that the four bowl mills are arranged on one side of the steam generator. The plant is constructed with upper air nozzles which are arranged above the top burner level for the reduced of nitrogen oxides. During tests at steam generator with similar design, the nO x formation could be reduced from 750 to 500 mg/m 3 s.t.p. (dry, 6% O 2 ) with an addition of upper air of 20% at 100% unit capacity and constant total flow. As a main approach for the further reduction of the primary NO x emission at bituminous coal fired steam generators with tangential firing systems, the experience gained from the firing of brown coal has also been taken into account. A fundamental aspect in this respect was the vertical air staging in the direction of the furnace height. The results of many tests in a test reactor have shown that the differences of the achievable NO x values of brown and

  5. Pretreatment of bituminous coal for hydrogenation (older experiments)

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer, H.

    1943-03-29

    The tendency for coal paste to become plastic inside a certain temperature range, which sometimes caused plugging in the preheater tubes, was observed only in bituminous coal. This phenomenon, called swelling, was seen as parallel to the increase in volume of the coal in coking or carbonization, which had been observed with melting bituminous coal. Although the parallel did not hold for all cases, the frequent simultaneous occurrence of the two phenomena suggested the possibility that those treatments of coal which reduced its baking ability would also improve its behavior in the preheater. Unequivocal results were not obtained, but certain predictions could be made about a pretreatment of coal for hydrogenation. (1) With preheating, no influence with regard to pressure plugging was detected in Brassert coal, although Saar coal Louisenthal, preheated, produced a better asphalt content and lower gasification experimentally. (2) Change in coal due to anoxidation increased the viscosity of the coal paste, while preheating in vacuum had no effect. (3) The baking ability of Saar coal could be destroyed by a sulfur treatment, without appreciably diminishing the volatile content. In general, a distinct improvement was observed with the absorption of sulfur.

  6. Co-pyrolysis characteristic of biomass and bituminous coal.

    Science.gov (United States)

    Li, Shuaidan; Chen, Xueli; Liu, Aibin; Wang, Li; Yu, Guangsuo

    2015-03-01

    Co-pyrolysis characteristics of biomass and bituminous coal have been studied in this work. The temperature was up to 900°C with the heating rates of 10, 15, 20, 25 and 30°C/min. Rice straw, saw dust, microcrystalline cellulose, lignin and Shenfu bituminous coal were chosen as samples. Six different biomass ratios were used. The individual thermal behavior of each sample was obtained. The experimental weight fractions of the blended samples and the calculated values were compared. The results show that the weight fractions of the blended samples behave differently with calculated ones during the co-pyrolysis process. With the increasing biomass ratio, relative deviations between experimental weight fractions and calculated ones are larger. H/C molar ratio, heat transfer properties of biomass would affect to the interaction between biomass and coal. The maximum degradation rates are slower than the calculated ones. The activation energy distributions also changed by adding some biomass into coal. Copyright © 2014 Elsevier Ltd. All rights reserved.

  7. Natural radioactivity associated with bituminous coal mining in Nigeria

    International Nuclear Information System (INIS)

    Balogun, F.A.; Mokobia, C.E.; Fasasi, M.K.; Ogundare, F.O.

    2003-01-01

    Gamma spectroscopic method was used to determine the natural radioactivity associated with the mining of Nigerian bituminous coal for the purpose of determining the radiological implications of coal mining in the country. The activity concentrations of the radionuclides detected range from 0.20±0.002 to 48.42±5.32 Bq kg -1 . The overall natural radionuclide contribution to the radioactivity of the environment was found to be 404.16±23.44 Bq kg -1 . Of this, coal waste (tailing) alone contributed 49.5% representing the largest contribution. Coal contributed just 5.5%. A comparison of the concentrations obtained in this work for coal with those from other parts of the world indicates that the radioactivity content of the Nigerian bituminous coal is not significantly different. The outdoor and indoor exposure rates in air 1 m above the ground are estimated to be (6.31±1.20)x10 -8 and (7.57±1.20) x10 -8 Gy h -1 , respectively, for the mining environment. These values compare very well with the global values reported by UNSCEAR: 5x10 -8 and 6x10 -8 Gy h -1 , respectively. The resulting annual effective dose equivalent estimated is (4.49±0.74)x10 -4 Sv yr -1 . This also compares favourably with the global value -4x10 -4 Sv yr -1 , reported by UNSCEAR

  8. Study of thermal reactivity during bituminization of radioactive waste

    International Nuclear Information System (INIS)

    Mouffe, Sh.

    2004-10-01

    This work deals with the study of chemical reactions and phases transitions which can occur between magnesium nitrate, sodium nitrate, cobalt sulphur product, and nickel potassium ferrocyanide, when they are heated together during bituminization process of nuclear waste. The applied methodology associates a few techniques: temperature, enthalpy, and kinetics of reaction are determined by calorimetry, reaction products are characterised by chemical analyses, mass spectrometry and XRD analysis. Three fields of temperature and energy are observed in function of composition (one compound or a mixture of compounds). The study of reactions between NaNO 3 and cobalt sulphur product shows that the presence of water has got an effect on reaction temperature. The study of Mg(NO 3 ) 2 , 6 H 2 O and CoS shows an overlapping of different signals, and that the reaction rate is very slow (a few hours). (author)

  9. Environmental problems caused by bituminous schist and possible solutions

    International Nuclear Information System (INIS)

    Elmas, N.; Aykul, H.; Erarslan, K.; Ediz, I.G.

    1998-01-01

    Schist, as a disposal of mine, has harmful effects on environment. however, several manners can be utilized to prevent the environmental destruction as well as an economical benefit is gained. In this study, environmental problems caused by bituminous schist and other disposals have been investigated on a specific lignite coal mine where schist is disposed as waste material. Pollution and damage on land and in water sources around the coal district and the villages have been observed, recorded and several solutions to environmental problems have been proposed. Discussed proposals will not only solve the environmental pollution problem but also provide waste management facility. Industrial structure of the district enables such a disposal to be used as an economical raw material. Besides, general effects of the coal mine and the power plant nearby have been discussed from environmental point of view, too. 7 refs

  10. Optimization of the encapsulation process of bituminized radioactive wastes

    International Nuclear Information System (INIS)

    Silva, Jarine E.C.; Tello, Clédola C.O.

    2017-01-01

    The objective of this paper is to propose alternatives for the deposition of bituminized waste in metallic packages coated with a cementitious matrix for surface repository, aiming to meet the standards criteria and increasing the integrity of the metallic packaging during the planned storage time, transportation and disposal. For this purpose, tests will be carried out to evaluate cement pastes and mortar with cementitious additives, aiming at the durability and reduction of pores. Leaching tests with different thicknesses will also be carried out, where optimization of the encapsulation can meet safety, durability and economy standards for the repository, as well as practices that contribute to reduce environmental impacts and the economic burden imposed on future generations

  11. Application of infrared camera to bituminous concrete pavements: measuring vehicle

    Science.gov (United States)

    Janků, Michal; Stryk, Josef

    2017-09-01

    Infrared thermography (IR) has been used for decades in certain fields. However, the technological level of advancement of measuring devices has not been sufficient for some applications. Over the recent years, good quality thermal cameras with high resolution and very high thermal sensitivity have started to appear on the market. The development in the field of measuring technologies allowed the use of infrared thermography in new fields and for larger number of users. This article describes the research in progress in Transport Research Centre with a focus on the use of infrared thermography for diagnostics of bituminous road pavements. A measuring vehicle, equipped with a thermal camera, digital camera and GPS sensor, was designed for the diagnostics of pavements. New, highly sensitive, thermal cameras allow to measure very small temperature differences from the moving vehicle. This study shows the potential of a high-speed inspection without lane closures while using IR thermography.

  12. Influence of association of "EVA-NBR" on indirect tensile strength of modified bituminous concrete

    Science.gov (United States)

    Chinoun, M.; Soudani, K.; Haddadi, S.

    2016-04-01

    The aim of this work is to contribute to the improvement of the mechanical properties of bituminous concrete by modification of bituminous concrete. In this study, we present the results of the indirect tensile strength "ITS" of modified bituminous concrete by the combination of two modifiers, one is a plastomer EVA (Ethylene Vinyl Acetate) and the other is a industrial waste from the shoe soles grinding NBR (Nitrile Butadiene Rubber) as crumb rubber. To modify the bitumen a wet process was used. The results show that the modification of bitumen by EVA-NBR combination increases their resistance to the indirect traction "ITS" compared to the bituminous concrete control. The mixture of 5% [50% EVA+ 50% NBR] is given the best result among the other associations.

  13. State of the art report on bituminized waste forms of radioactive wastes

    International Nuclear Information System (INIS)

    Kim, Tae Kook; Shon, Jong Sik; Kim, Kil Jeong; Lee, Kang Moo; Jung, In Ha

    1998-03-01

    In this report, research and development results on the bituminization of radioactive wastes are closely reviewed, especially those regarding waste treatment technologies, waste solidifying procedures and the characteristics of asphalt and solidified forms. A new concept of the bituminization method is suggested in this report which can improve the characteristics of solidified forms. Stable solid forms with high leach resistance, high thermal resistance and good compression strength were produced by the suggested bituminization method, in which spent polyethylene from agricultural farms was added. This report can help further research and development of improved bituminized forms of radioactive wastes that will maintain long term stabilities in disposal sites. (author). 59 refs., 19 tabs., 18 figs

  14. A new radiometric instrument designed to measure the parameters of bituminous coal on transport belts

    International Nuclear Information System (INIS)

    Kubicek, P.

    1993-01-01

    A new radiometric instrument developed in Czechoslovakia, for the measurement of ash content of bituminous coal, and for the determination of approximate values of moisture and weight is described. (Author)

  15. Investigation on Using SBS and Active Carbon Filler to Reduce the VOC Emission from Bituminous Materials

    OpenAIRE

    Cui, Peiqiang; Wu, Shaopeng; Li, Fuzhou; Xiao, Yue; Zhang, Honghua

    2014-01-01

    Bituminous materials are playing a vital role in pavement design and the roofing industry because of outstanding properties. Unfortunately, bituminous materials will release volatile organic compounds (VOC), making them non-environmentally friendly. Therefore, technologies that can be used to decrease the VOC emission are urgently required. In this research, the VOC emission and material behaviors were analyzed and compared to investigate the possibility of adding styrene butadiene styrene (S...

  16. Investigation and analytical results of bituminized products in drums at filing room

    International Nuclear Information System (INIS)

    Shibata, Atsuhiro; Kato, Yoshiyuki; Sano, Yuichi; Kitajima, Takafumi; Fujita, Hideto

    1999-09-01

    This report describes the results of investigation of the bituminized products in drums, liquid waste in the receiving tank V21 and the bituminized mixture in the extruder. The investigation of the products in drums showed most of the unburned products filled after 28B had abnormality, such as hardened surfaces, caves and porous brittle products. The particle sizes of the salt fixed in bituminized products depended neither on batch number nor on feed rate. It indicates the fining of the salt particle caused by the decreased feed rate did not occur. The measured concentrations of metals and anions in the bituminized products showed no abnormality. The catalytic content was not recognized in the products. The infrared absorption spectra obtained with the bituminized products show the oxidation at the incident occurred without oxygen. There was no organic phase on the surface of liquid waste in V21. Chemical analysis and thermal analysis on the precipitate in V21 showed no abnormality. Concentration of sodium nitrate/nitrite in the mixture collected from the extruder was lower than normal products. These results show no chemical activation of the bituminized products. It can be concluded that the chemical characteristics of the products had little abnormality even around the incident. (author)

  17. Bituminous reference document: synthesis of knowledge on the long time behavior of bituminous packages; Dossier de reference bitume: synthese des connaissances sur le comportement a long terme des colis bitumes

    Energy Technology Data Exchange (ETDEWEB)

    Sercombe, J.; Adenot, F.; Vistoli, P.P.; Parraud, S.; Riglet-Martial, C.; Gwinner, B.; Felines, I.; Tiffreau, C.; Libert, M

    2004-07-01

    This document is a synthesis of the knowledge acquired at the CEA on the behavior of bituminous packages. In this framework, the CEA studied bituminous packages in generic conditions of a package lifetime. The main factors, the evolution mechanisms and influential parameters have been determined and quantitative s simulation have been developed. After a description of the main initial bituminous packages characterizations, the evolutions in saturated and un-saturated environment are exposed. (A.L.B.)

  18. Development of bituminous coal chambers with respect to throughput

    Energy Technology Data Exchange (ETDEWEB)

    Schappert, H.

    1942-10-17

    This short report compared three coal liquefaction plants in Germany which operated principally on bituminous coal and which had been built a few years apart in time. From the earliest plant (Scholven) to the latest (Blechhammer), the liquid-phase throughput had been almost tripled, partly because of the change from 300-atm to 700-atm operation, and partly because of the use of heat exchange to heat the coal paste part way to reaction temperature. This introduction of coal paste heat exchange reduced the load on preheaters so much that the amount of heat necessary in the preheater to heat one (metric) ton of coal paste to reaction temperature was reduced from 320,000 kcal to 170,000 kcal. Another development in the middle plant (Gelsenberg) was the addition of a portion of the cold coal paste at the input to the second reaction oven in each chamber, letting the heat of reaction itself heat that paste to reaction temperature (and at the same time regulating the temperature of the reaction better). Finally it was noted that for the production of a given amount of synthetic fuel, Blechhammer needed only about half as many reaction chambers as did Scholven.

  19. The hydrogasification of lignite and sub-bituminous coals

    Science.gov (United States)

    Bhatt, B.; Fallon, P. T.; Steinberg, M.

    1981-02-01

    A North Dakota lignite and a New Mexico sub-bituminous coal have been hydrogenated at up to 900°C and 2500 psi hydrogen pressure. Yields of gaseous hydrocarbons and aromatic liquids have been studied as a function of temperature, pressure, residence time, feed rates and H2/coal ratio. Coal feed rates in excess of 10 lb/hr have been achieved in the 1 in. I. D.×8 ft reactor and methane concentration as high as 55% have been observed. A four-step reaction model was developed for the production and decomposition of the hydrocarbon products. A single object function formulated from the weighted errors for the four dependent process, variables, CH4, C2H6, BTX, and oil yields, was minimized using a program containing three independent iterative techniques. The results of the nonlinear regression analysis for lignite show that a first-order chemical reaction model with respect to C conversion satisfactorily describes the dilute phase hydrogenation. The activation energy for the initial products formation was estimated to be 42,700 cal/gmole and the power of hydrogen partial pressure was found to be +0.14. The overall correlation coefficient was 0.83. The mechanism, the rate expressions, and the design curves developed can be used for scale-up and reactor design.

  20. A process for the bituminization of radioactive wastes

    International Nuclear Information System (INIS)

    Bar-Ziv, E.; Manor, D.; Levin, I.

    1977-06-01

    A process is described for the incorporation of sodium nitrate solutions in bitumen, with a view to the bituminization of radioactive wastes. This process has involved the development of a chemical process and its technological application. A double jacket reactor equipped with an anchor-type stirrer has been built. Sodium nitrate (NaNO 3 ) solutions with sodium hydroxide (NaOH) are fed into the reactor simultaneously with a bitumen emulsion while heated oil is circulated through the double jacket. After all the water has evaporated, the mixture is ''simmered'' at 170/180 deg C for up to 5 hours in order to get a homogeneous product which will be suitable for final storage. The product contains small salt crystals (10/50 μm) and has high viscosity (200/2000 poise at 160 deg C and 12 rpm), so that the possibility of sedimentation is eliminated. In comparative experiments with molten bitumen, large salt aggregates, inhomogeneously distributed, make the product unsuitable. It has been found that NaOH is responsible for the polimerization of the bitumen, which raises its viscosity. The degree of polimerization depends on the NaOH concentration and ''simmering'' time and temperature. NaOH is added to NaNO 3 in order to raise the mixture's viscosity and thereby prevent sedimentation

  1. Chemical and Pyrolytic Thermogravimetric Characterization of Nigerian Bituminous Coals

    Directory of Open Access Journals (Sweden)

    Nyakuma Bemgba Bevan

    2016-12-01

    Full Text Available The discovery of new coal deposits in Nigeria presents solutions for nation’s energy crises and prospects for socioeconomic growth and sustainable development. Furthermore, the quest for sustainable energy to limit global warming, climate change, and environmental degradation has necessitated the exploration of alternatives using cleaner technologies such as coal pyrolysis. However, a lack of comprehensive data on physico-chemical and thermal properties of Nigerian coals has greatly limited their utilization. Therefore, the physico-chemical properties, rank (classification, and thermal decomposition profiles of two Nigerian bituminous coals – Afuze (AFZ and Shankodi-Jangwa (SKJ – were examined in this study. The results indicate that the coals contain high proportions of C, H, N, S, O and a sufficiently high heating value (HHV for energy conversion. The coal classification revealed that the Afuze (AFZ coal possesses a higher rank, maturity, and coal properties compared to the Shankodi-Jangwa (SKJ coal. A thermal analysis demonstrated that coal pyrolysis in both cases occurred in three stages; drying (30-200 °C, devolatilization (200-600 °C, and char decomposition (600-1000 °C. The results also indicated that pyrolysis at 1000 °C is not sufficient for complete pyrolysis. In general, the thermochemical and pyrolytic fuel properties indicate that the coal from both places can potentially be utilized for future clean energy applications.

  2. Adhesion Promoters in Bituminous Road Materials: A Review

    Directory of Open Access Journals (Sweden)

    Cesare Oliviero Rossi

    2017-05-01

    Full Text Available This review focuses on certain classes of organic compounds known variously in the specific literature of asphalt as adhesion promoters, antistripping agents, wetting agents, antistrips, or adhesion agents. These kinds of organic additives are currently formulated to enhance the bitumen coating of mineral aggregates and improve the workability of asphalt mixtures. In this review, the term “adhesion promoters” includes both synthetic organic compounds as well as those extracted from natural resources, mixed in trace amounts to bitumen. Their main role is to alter the interfacial energy, so that the presence of water, even in trace, does not weaken the bitumen-aggregate bond and tends to favor adhesion. The report also considers the chemical functionalities that play a predominant role in bonding, as well as the effects of surface modification of the aggregate due to the presence of adhesion promoters in pre-blended bituminous mixtures. Although bitumen is widely used in road pavement construction and the discussion is mainly addressed to the improvement of adhesion in road materials, adhesion and wetting properties can also represent a general issue in various bitumen-based industrial products.

  3. Gasification of high ash, high ash fusion temperature bituminous coals

    Science.gov (United States)

    Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

    2015-11-13

    This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

  4. Investigation on Using SBS and Active Carbon Filler to Reduce the VOC Emission from Bituminous Materials

    Directory of Open Access Journals (Sweden)

    Peiqiang Cui

    2014-08-01

    Full Text Available Bituminous materials are playing a vital role in pavement design and the roofing industry because of outstanding properties. Unfortunately, bituminous materials will release volatile organic compounds (VOC, making them non-environmentally friendly. Therefore, technologies that can be used to decrease the VOC emission are urgently required. In this research, the VOC emission and material behaviors were analyzed and compared to investigate the possibility of adding styrene butadiene styrene (SBS and active carbon filler into bituminous materials to develop environmentally-friendly materials. Thermal gravimetric analysis-mass spectrometry (TG-MS and ultraviolet-visible spectroscopy testing (UV-Vis were employed to characterize the VOC emission process. Temperature sweep testing and frequency sweep testing were conducted to evaluate the rheological properties of bituminous materials. Research results indicated that the combined introduction of 4 wt% styrene butadiene styrene (SBS and 4 wt% active carbon filler cannot only significantly lower the VOC emission speed and amount, but also improve the deformation resistance behavior at a higher temperature. SBS and active carbon filler can be used to reduce the VOC emission form bituminous materials.

  5. Investigation on Using SBS and Active Carbon Filler to Reduce the VOC Emission from Bituminous Materials.

    Science.gov (United States)

    Cui, Peiqiang; Wu, Shaopeng; Li, Fuzhou; Xiao, Yue; Zhang, Honghua

    2014-08-26

    Bituminous materials are playing a vital role in pavement design and the roofing industry because of outstanding properties. Unfortunately, bituminous materials will release volatile organic compounds (VOC), making them non-environmentally friendly. Therefore, technologies that can be used to decrease the VOC emission are urgently required. In this research, the VOC emission and material behaviors were analyzed and compared to investigate the possibility of adding styrene butadiene styrene (SBS) and active carbon filler into bituminous materials to develop environmentally-friendly materials. Thermal gravimetric analysis-mass spectrometry (TG-MS) and ultraviolet-visible spectroscopy testing (UV-Vis) were employed to characterize the VOC emission process. Temperature sweep testing and frequency sweep testing were conducted to evaluate the rheological properties of bituminous materials. Research results indicated that the combined introduction of 4 wt% styrene butadiene styrene (SBS) and 4 wt% active carbon filler cannot only significantly lower the VOC emission speed and amount, but also improve the deformation resistance behavior at a higher temperature. SBS and active carbon filler can be used to reduce the VOC emission form bituminous materials.

  6. Leaching behavior of a simulated bituminized radioactive waste form under deep geological conditions

    International Nuclear Information System (INIS)

    Nakayama, Shinichi; Iida, Yoshihisa; Nagano, Tetsushi; Akimoto, Toshiyuki

    2003-01-01

    The leaching behavior of a simulated bituminized waste form was studied to acquire data for the performance assessment of the geologic disposal of bituminized radioactive waste. Laboratory-scale leaching tests were performed for radioactive and non-radioactive waste specimens simulating bituminized waste of a French reprocessing company, COGEMA. The simulated waste was contacted with deionized water, an alkaline solution (0.03-mol/l KOH), and a saline solution (0.5-mol/l KCl) under atmospheric and anoxic conditions. The concentrations of Na, Ba, Cs, Sr, Np, Pu, NO 3 , SO 4 and I in the leachates were determined. Swelling of the bituminized waste progressed in deionized water and KOH. The release of the soluble components, Na and Cs, was enhanced by the swelling, and considered to be diffusion-controlled in the swelled layers of the specimens. The release of sparingly soluble components such as Ba and Np was solubility-limited in addition to the progression of leaching. Neptunium, a redox-sensitive element, showed a distinct difference in release between anoxic and atmospheric conditions. The elemental release from the bituminized waste specimens leached in the KCl was very low, which is likely due to the suppression of swelling of the specimens at high ionic strength. (author)

  7. Surface Properties of Photo-Oxidized Bituminous Coals: Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Natural weathering has a detrimental effect on the hydrophobic nature of coal, which in turn can influence clean-coal recovery during flotation. Few techniques are available that can establish the quality of coal surfaces and that have a short analysis time to provide input for process control. Luminescence emissions which can be quantified with an optical microscope and photometer system, are measurably influenced by degree of weathering as well as by mild storage deterioration. In addition, it has been shown that when vitrinite is irradiated with a relatively high intensity flux of violet- or ultraviolet- light in the presence of air, photo-oxidation of the surface occurs. The combination of measuring the change in luminescence emission intensity with degree of surface oxidation provided the impetus for the current investigation. The principal aim of this research was to determine whether clear correlations could be established among surface oxygen functionality, hydrophobicity induced by photo-oxidation, and measurements of luminescence intensity and alteration. If successful, the project would result in quantitative luminescence techniques based on optical microscopy that would provide a measure of the changes in surface properties as a function of oxidation and relate them to coal cleanability. Two analytical techniques were designed to achieve these goals. Polished surfaces of vitrain bands or a narrow size fraction of powdered vitrain concentrates were photo-oxidized using violet or ultraviolet light fluxes and then changes in surface properties and chemistry were measured using a variety of near-surface analytical techniques. Results from this investigation demonstrate that quantitative luminescence intensity measurements can be performed on fracture surfaces of bituminous rank coals (vitrains) and that the data obtained do reveal significant variations depending upon the level of surface oxidation. Photo-oxidation induced by violet or ultraviolet light

  8. Global market trade policy analysis for petroleum oils and oils obtained from bituminous minerals, crude

    Directory of Open Access Journals (Sweden)

    Bagheri, F.

    2012-01-01

    Full Text Available This article is based on surveying the custom tariffs imposed on the world export market of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. We obtained the data according to the most updated available data provided online by UNCTAD and World Bank. The results indicate that none of the 142 countries in the world market of this product have imposed non-tariff trade barriers on the import of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. The developed countries and the countries with transition economies are the main world import partners. European Union, United States, China, Japan, South Korea, Canada, Singapore, Taiwan, Thailand, South Africa, Australia, Turkey, Brazil, Sweden and Belarus are the examples and have imposed low custom tariffs on Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude.

  9. Study on the coprocessing of Xingiang Heishan bituminous coal with Tahe petroleum residue

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, C.; Zhao, P.; Li, K. [China Shenhua Coal to Liquefaction Corporation Ltd., Ordo (China)

    2007-02-15

    The reaction process of coprocessing Xinjiang Heishan bituminous coal and petroleum residue from Tahe petroleum chemical corporation was studied by using a Japanese vibrating horizontal autoclave. The effects of different petroleum residual addition on coal liquefaction was investigated and compared with the liquefaction result under the condition of exclusive Heishan bituminous coal. The results show that compared with the liquefaction results with only Heishan bituminous coal, coal-residual coprocessing has the characteristics of low hydrogen consumption, low gas and high oil yield. Coal conversion and oil yield was increased with proper addition of petroleum residues. In this experimental system, the optimum addition of petroleum residue is 20%. Coal conversion and oil yield are increased by 1.5% and 11% respectively. 2 refs., 1 fig., 5 tabs.

  10. Results of exploitation of a pilot-plant installation for bituminization of radioactive sludges

    International Nuclear Information System (INIS)

    Golinski, M.; Ksiazak, Z.; Surala, J.; Dziubecki, R.

    1974-01-01

    Results are discussed of exploitation of a pilot-plant installation for bituminization of radioactive sludges of an efficiency of 25 l/h. In a time period of 20 month 120 cycles were carried out in which 60 m 3 of 2-4% sludges from treatment of low-level waste by the phosphate-ferrocyanide method were solidified. The P-60 asphalt was used for bituminization. The bituminization products contained 5-13.5% of mineral substances. Their activity was in the range 5 x 10 -4 - 5 x 10 -3 μCi/g for alpha emitters and 1.2 - 3.8 x 10 -2 μCi/g for beta emitters. (author)

  11. Estimated Valuation of the Cost of Road Construction with the Use of Composite Cationic Bituminous Structures

    Directory of Open Access Journals (Sweden)

    Vorotynseva Anna

    2017-01-01

    Full Text Available The need for formation of prices for road construction works producing, by using composite of cationic bituminous structures, is dictated by absence of this type of work in estimate-normative base, due to the fact that this type of materials had never been used before. Estimated specifications could be used either for determination of work cost or for substantiation of efficiency of using new type of materials. This paper provides basic concepts, related to formation of estimate-normative base for determination of construction and installation works cost, particularly road construction works, also it shows formation of coating installation prices by using composite of cationic bituminous emulsions.

  12. Microstructural self-healing of bituminous materials : Combined experimental and numerical study

    NARCIS (Netherlands)

    Pauli, A.; Schmets, A.J.M.; Kasbergen, C.; Varveri, K.; Scarpas, A.

    2013-01-01

    Bituminous materials form a class of materials that possess the intrinsic ability to selfheal. This self-healing capability is evidenced by the observation that the service life of these materials ‘in the field’ exceeds the service life as predicted by standard mechanical laboratory tests. This

  13. The X-ray fluorescent method for determination of total sulphur in bituminous coals

    International Nuclear Information System (INIS)

    Widowska-Kusmierska, J.; Siess, K.

    1979-01-01

    The X-ray fluorescent technique for the determination of total sulphur covering concentrations from 0,1 to 10% has been applied for bituminous coals showing a great variability in qualitative and quantitative composition of mineral matter (ash). The described method is a quick one giving results during one hour. The obtained good accuracy of determinations gives prospects for wide industrial application. (author)

  14. Assessment of underground coal gasification in bituminous coals. Volume I. Executive summary. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-01-01

    This report describes the bituminous coal resources of the United States, identifies those resources which are potentially amenable to Underground Coal Gasification (UCG), identifies products and markets in the vicinity of selected target areas, identifies UCG concepts, describes the state of the art of UCG in bituminous coal, and presents three R and D programs for development of the technology to the point of commercial viability. Of the 670 billion tons of bituminous coal remaining in-place as identified by the National Coal Data System, 32.2 billion tons or 4.8% of the total are potentially amenable to UCG technology. The identified amenable resource was located in ten states: Alabama, Colorado, Illinois, Kentucky, New Mexico, Ohio, Oklahoma, Utah, Virginia, and West Virginia. The principal criteria which eliminated 87.3% of the resource was the minimum thickness (42 inches). Three R and D programs were developed using three different concepts at two different sites. Open Borehole, Hydraulic Fracture, and Electrolinking concepts were developed. The total program costs for each concept were not significantly different. The study concludes that much of the historical information based on UCG in bituminous coals is not usable due to the poor siting of the early field tests and a lack of adequate diagnostic equipment. This information gap requires that much of the early work be redone in view of the much improved understanding of the role of geology and hydrology in the process and the recent development of analytical tools and methods.

  15. Effect of bituminous coal properties on carbon dioxide and methane high pressure sorption

    Czech Academy of Sciences Publication Activity Database

    Weishauptová, Zuzana; Přibyl, Oldřich; Sýkorová, Ivana; Machovič, Vladimír

    2015-01-01

    Roč. 139, JAN 1 (2015), s. 115-124 ISSN 0016-2361 Institutional support: RVO:67985891 Keywords : bituminous coal * sorption capacity * maceral composition * Upper Silesian Coal Basin Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.611, year: 2015

  16. Noise Reduction Properties of an Experimental Bituminous Slurry with Crumb Rubber Incorporated by the Dry Process

    Directory of Open Access Journals (Sweden)

    Moisés Bueno

    2014-08-01

    Full Text Available Nowadays, cold technology for asphalt pavement in the field of road construction is considered as an alternative solution to conventional procedures from both an economic and environmental point of view. Among these techniques, bituminous slurry surfacing is obtaining an important role due to the properties of the obtained wearing course. The functional performance of this type of surfaces is directly related to its rough texture. Nevertheless, this parameter has a significant influence on the tire/road noise generation. To reduce this undesirable effect on the sound performance, new designs of elastic bituminous slurries have been developed. Within the FENIX project, this work presents the acoustical characterization of an experimental bituminous slurry with crumb rubber from wasted automobile tires incorporated by the dry process. The obtained results show that, under controlled operational parameters, the close proximity sound levels associated to the experimental slurry are considerably lower than those emitted by a conventional slurry wearing course. However, after one year of supporting traffic loads and different weather conditions, the evaluated bituminous slurry, although it conserves the original noise reduction properties in relation to the conventional one, noticeably increases the generated sound emission. Therefore, it is required to continue improving the design of experimental surfaces in order to enhance its long-term performance.

  17. Chemomechanics of Damage Accumulation and Damage-Recovery Healing in Bituminous Asphalt Binders

    NARCIS (Netherlands)

    Pauli, A.T.

    2014-01-01

    As a contribution to the development of mutli-scale multi-physics approaches to modelling pavement performance, the present thesis considers the topic of damage accumulation accompanied by damage recover self-healing of the bituminous asphalt phase of pavement systems. It is found insightful that by

  18. 8th RILEM International Symposium on Testing and Characterization of Sustainable and Innovative Bituminous Materials

    CERN Document Server

    Partl, Manfred

    2016-01-01

    This work presents the results of RILEM TC 237-SIB (Testing and characterization of sustainable innovative bituminous materials and systems). The papers have been selected for publication after a rigorous peer review process and will be an invaluable source to outline and clarify the main directions of present and future research and standardization for bituminous materials and pavements. The following topics are covered: - Characterization of binder-aggregate interaction - Innovative testing of bituminous binders, additives and modifiers - Durability and aging of asphalt pavements - Mixture design and compaction analysis - Environmentally sustainable materials and technologies - Advances in laboratory characterization of bituminous materials - Modeling of road materials and pavement performance prediction - Field measurement and in-situ characterization - Innovative materials for reinforcement and interlayer systems - Cracking and damage characterization of asphalt pavements - Rec...

  19. Pre-treatment of bituminized NPP wastes for disposal in near-surface repository

    Energy Technology Data Exchange (ETDEWEB)

    Vieira, Vanessa Mota; Tello, Clédola Cássia Oliveira de, E-mail: vanessamotavieira@gmail.com, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2017-07-01

    The implementation of the national repository is an important technical requirement, and a legal requirement for the entry into operation of the nuclear power plant Angra 3. The Brazilian repository is being planned to be a near-surface one. In Brazil the low and intermediate level radioactive wastes are immobilized using cement and bitumen for Angra 1 and Angra 2 NPP, respectively. The main problems due to the disposal of bituminized wastes in repositories are swelling of the waste products and their degradation in the long term. To accommodate the swelling of the bituminized wastes, the drums are filled up to 70 - 90% of their volume, which reduces the structural the repository stability and the disposal availability. Countries, which use bitumen in the solidification of NPP's radioactive waste and have near-surface repositories, need to immobilize this bituminized waste within other drums containing cement pastes or mortars to disposal them. This study aims to find solutions for the storage in surface repository of bituminized radioactive waste products, making them compatible with the acceptance criteria of cemented waste products. It was also performed a modeling with the results obtained in the leaching test using the ALT program and defined the transport model of the cesium leachate element and it was verified that in the early times the leaching was governed by the diffusion model and later by the partition model. The results obtained in this study can be used in the evaluation of performance of repositories. (author)

  20. Aerobic Biofilms Grown from Athabasca Watershed Sediments Are Inhibited by Increasing Concentrations of Bituminous Compounds

    Science.gov (United States)

    Lawrence, John R.; Sanschagrin, Sylvie; Roy, Julie L.; Swerhone, George D. W.; Korber, Darren R.; Greer, Charles W.

    2013-01-01

    Sediments from the Athabasca River and its tributaries naturally contain bitumen at various concentrations, but the impacts of this variation on the ecology of the river are unknown. Here, we used controlled rotating biofilm reactors in which we recirculated diluted sediments containing various concentrations of bituminous compounds taken from the Athabasca River and three tributaries. Biofilms exposed to sediments having low and high concentrations of bituminous compounds were compared. The latter were 29% thinner, had a different extracellular polysaccharide composition, 67% less bacterial biomass per μm2, 68% less cyanobacterial biomass per μm2, 64% less algal biomass per μm2, 13% fewer protozoa per cm2, were 21% less productive, and had a 33% reduced content in chlorophyll a per mm2 and a 20% reduction in the expression of photosynthetic genes, but they had a 23% increase in the expression of aromatic hydrocarbon degradation genes. Within the Bacteria, differences in community composition were also observed, with relatively more Alphaproteobacteria and Betaproteobacteria and less Cyanobacteria, Bacteroidetes, and Firmicutes in biofilms exposed to high concentrations of bituminous compounds. Altogether, our results suggest that biofilms that develop in the presence of higher concentrations of bituminous compounds are less productive and have lower biomass, linked to a decrease in the activities and abundance of photosynthetic organisms likely due to inhibitory effects. However, within this general inhibition, some specific microbial taxa and functional genes are stimulated because they are less sensitive to the inhibitory effects of bituminous compounds or can degrade and utilize some bitumen-associated compounds. PMID:24056457

  1. Treatments for clays in aggregates used to produce cement concrete, bituminous materials, and chip seals : technical report.

    Science.gov (United States)

    2013-07-01

    The clay contamination of coarse and fine aggregates and its effects on pavement performance of portland cement concrete, bituminous mixes and chip seals is a major concern for Texas Department of Transportation. We proposed (i) to determine what typ...

  2. Use of additives to improve the capacity of bituminous mixtures to be heated by means of microwaves

    International Nuclear Information System (INIS)

    Gallego, J.; Val, M.A. del; Contreras, V.; Páez, A.

    2017-01-01

    This study examines the potential of adding electric arc furnace slag to bituminous mixtures to be heated by microwaves. The susceptibility of bituminous mixtures to microwave energy is limited and so, in order to improve the energy performance of the heating process, it is necessary to incorporate additives or components to the mixture so as to improve the capacity for microwave heating. The article presents the results of adding various components, (steel wool, scrap tire wire, silicon carbide, iron filings) and an alternative aggregate: electric arc furnace slag. According to the results obtained in the laboratory, slag addition of at least 5% by weight of the bituminous mixture represents the best option for both technical and economic reasons. The results may promote the valorization of this steel industry residue in bituminous mixtures by improving microwave heating response. [es

  3. Water Accumulation and Behavior of Surfactant Associated with Moisture Permeation in Bituminous Pavement on Concrete Deck Bridge

    OpenAIRE

    Sasaki, Iwao; Moriyoshi, Akihiro; Tsunekawa, Masami

    2006-01-01

    Water-related damage is one of the major problems for the durability of the bituminous pavement and concrete slabs of concrete deck bridges. In particular, damage can be drastically accelerated by the intervention of water and some chemicals such as surfactants and salts. Therefore, the mass transfer mechanism of water and the mechanism of chemical absorption in pavement materials are important to study. The authors previously pointed out that water storage in bituminous pavement layers is ca...

  4. Long-term behaviour of bituminized waste: modelling self-irradiation and leaching

    Energy Technology Data Exchange (ETDEWEB)

    Simondi-Teisseire, B.; Vistoli, P.P.; Libert, M.; Gilardi, T. [CEA Cadarache, Dept. de Physico-Chimie, DPC, 13 - Saint-Paul-lez-Durance (France); Chaix, P. [CEA Saclay, Dept. de Physico-Chimie, DPC, 91 - Gif-sur-Yvette (France); Blanc, V. [Cogema, 78 - Saint Quentin en Yvelines (France)

    2001-07-01

    During interim storage, the main evolution factor of bituminized wastes is radiolysis, due to self-irradiation. In deep disposal conditions, after site re-saturation and corrosion of the containers, the main evolution will be due to leaching. This paper deals with two models designed to describe respectively radiolytic gas evacuation (JACOB- 2) and bituminized waste leaching (COLONBO), and some of the typical results obtained from these two models. The first model describes radiolytic gas production, diffusive transport of gas, bubble nucleation and ripening and movement under buoyancy. The second one is based on descriptions of water sorption, solubilization, and diffusion into the matrix, water uptake by the most soluble salts leading to alteration of the matrix and finally to diffusive transport of the salts outside the bitumenisate. (author)

  5. Research on the thermal decomposition of Mongolian Baganuur lignite and Naryn sukhait bituminous coal

    Directory of Open Access Journals (Sweden)

    A. Ariunaa

    2016-03-01

    Full Text Available The technical characteristics, elemental composition of the organic and mineral matters, ash melting behaviors and carbonization and gasification reactivities of coals from Baganuur and Naryn sukhait deposits were investigated. The results of proximate and ultimate analysis confirmed that the coal from Baganuur deposit can be graded as a low rank lignite B2 mark coal and Naryn sukhait coal is a bituminous G mark one. The carbonization and gasification experiments were performed using TGA apparatus and fixed bed quartz reactor. The data obtained with two experimental reactors showed that Baganuur lignite had lower thermal stability and much higher CO2 gasification reactivity at 950°C as compared to those for Naryn sukhait bituminous coal.Mongolian Journal of Chemistry 16 (42, 2015, 22-29

  6. Estimated Valuation of the Cost of Road Construction with the Use of Composite Cationic Bituminous Structures

    OpenAIRE

    Vorotynseva Anna; Ovsiannikov Andrey; Bolgov Vladimir

    2017-01-01

    The need for formation of prices for road construction works producing, by using composite of cationic bituminous structures, is dictated by absence of this type of work in estimate-normative base, due to the fact that this type of materials had never been used before. Estimated specifications could be used either for determination of work cost or for substantiation of efficiency of using new type of materials. This paper provides basic concepts, related to formation of estimate-normative bas...

  7. Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

    OpenAIRE

    Sarkar, Dipankar; Pal, Manish; Sarkar, Ashoke K.

    2016-01-01

    There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46...

  8. [Determination of aromatic polycyclic hydrocarbons during the installation of bituminous acoustic insulation panels].

    Science.gov (United States)

    Gianello, G; Marrubini, G; La Bua, R; Laurini, C; Bergamaschi, A

    2006-01-01

    Two kinds of bituminous European and Asiatic origin panels, used as acoustic insulators in the production of electrical household appliances have been analysed. The tests, made at 180 degrees C, operation temperature during the assembly phases, have been executed by sampling the smokes released during the thermal treatment, subsequently analysed by GC-MS. The results showed a marked difference between the two samples in the amount of the issued compounds, essentially constituted by alkyl-aromatic hydrocarbons, IPA and Alkyl-IPA.

  9. Noise Reduction Properties of an Experimental Bituminous Slurry with Crumb Rubber Incorporated by the Dry Process

    OpenAIRE

    Bueno, Moisés; Luong, Jeanne; Terán, Fernando; Viñuela, Urbano; Vázquez, Víctor; Paje, Santiago

    2014-01-01

    Nowadays, cold technology for asphalt pavement in the field of road construction is considered as an alternative solution to conventional procedures from both an economic and environmental point of view. Among these techniques, bituminous slurry surfacing is obtaining an important role due to the properties of the obtained wearing course. The functional performance of this type of surfaces is directly related to its rough texture. Nevertheless, this parameter has a significant influence on th...

  10. Carbon Isotope Analyses of Individual Hydrocarbon Molecules in Bituminous Coal, Oil Shale and Murchison Meteorite

    Directory of Open Access Journals (Sweden)

    Kyoungsook Kim

    1998-06-01

    Full Text Available To study the origin of organic matter in meteorite, terrestrial rocks which contain organic compounds similar to the ones found in carbonaceous chondrites are studied and compared with Murchison meteorite. Hydrocarbon molecules were extracted by benzene and methanol from bituminous coal and oil shale and the extracts were partitioned into aliphatic, aromatic, and polar fractions by silica gel column chromatography. Carbon isotopic ratios in each fractions were analysed by GC-C-IRMS. Molecular compound identifications were carried by GC-MS Engine. Bituminous coal and oil shale show the organic compound composition similar to that of meteorite. Oil shale has a wide range of δ(13C, -20.1%_0 - -54.4%_0 compared to bituminous coal, -25.2%_0 - -34.3%_0. Delta values of several molecular compounds in two terrestrial samples are different. They show several distinct distributions in isotopic ratios compared to those of meteorite; Murchison meteorite has a range of δ(13C from -13%_0 to +30%_0. These results provide interpretation for the source and the formation condition of each rock, in particular alteration and migration processes of organic matter. Especially, they show an important clue whether some hydrocarbon molecules observed in meteorite are indigenous or not.

  11. Prediction of Marshall Parameters of Modified Bituminous Mixtures Using Artificial Intelligence Techniques

    Directory of Open Access Journals (Sweden)

    Sunil Khuntia

    2014-09-01

    Full Text Available This study presents the application of artificial neural networks (ANN and least square support vector machine (LS-SVM for prediction of Marshall parameters obtained from Marshall tests for waste polyethylene (PE modified bituminous mixtures. Waste polyethylene in the form of fibres processed from utilized milk packets has been used to modify the bituminous mixes in order to improve their engineering properties. Marshall tests were carried out on mix specimens with variations in polyethylene and bitumen contents. It has been observed that the addition of waste polyethylene results in the improvement of Marshall characteristics such as stability, flow value and air voids, used to evaluate a bituminous mix. The proposed neural network (NN model uses the quantities of ingredients used for preparation of Marshall specimens such as polyethylene, bitumen and aggregate in order to predict the Marshall stability, flow value and air voids obtained from the tests. Out of two techniques used, the NN based model is found to be compact, reliable and predictable when compared with LS-SVM model. A sensitivity analysis has been performed to identify the importance of the parameters considered.

  12. Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Bauman, R.F.; Coless, L.A.; Davis, S.M. [and others

    1995-12-31

    In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263. Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.

  13. Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

    Directory of Open Access Journals (Sweden)

    Dipankar Sarkar

    2016-01-01

    Full Text Available There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46, 0.50, 0.54, and 0.60 of the weight of brick aggregates. Marshall Method of mix design is carried out to find the optimum bitumen content of such bituminous concrete mix prepared by plastic coated OBBA. Bulk density, Marshall Stability, flow, Marshall Quotient, ITS, TSR, stripping, fatigue life, and deformations have been determined accordingly. Marshall Stability value of 0.54 percent of plastic mix is comparatively higher than the other mixes except 0.60 percent of plastic mix. Test results are within the prescribed limit for 0.54 percent of plastic mix. There is a significant reduction in rutting characteristics of the same plastic mix. The fatigue life of the mix is also significantly higher. Thus plastic coated OBBA is found suitable in construction of bituminous concrete road.

  14. JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

    Energy Technology Data Exchange (ETDEWEB)

    Jason Laumb; John Kay; Michael Jones; Brandon Pavlish; Nicholas Lentz; Donald McCollor; Kevin Galbreath

    2009-03-29

    The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

  15. Towards improved correlations between bitumen properties and rutting resistance of bituminous mixtures - FunDBitS literature review

    Science.gov (United States)

    Batista, Fátima A.; Hofko, Bernhard; De Visscher, Joëlle; Tanghe, Tine; da Costa, Margarida Sá

    2017-09-01

    Bitumen is the most common binder used in the production of bituminous mixtures for road paving, having a fundamental influence on the performance of the pavement. However, it is not yet fully understood which bitumen properties have a significant influence on the behaviour of bituminous mixtures. In this context, the FunDBitS project was developed. Its main objective was to prepare recommendations on the properties of the bitumen to be specified in order to obtain suitable bituminous mixtures, namely in what concerns to its resistance to permanent deformation (rutting), stiffness, low temperature cracking, fatigue cracking and binder/aggregate interaction. In this framework, the research studies that have become internationally available since the BiTVal project were reviewed in order to assess performance-based bitumen characteristics, which may be introduced into bitumen specification standards. This paper specifically presents the main conclusions regarding the properties of bitumen related to the behaviour to permanent deformation of bituminous mixtures. It was concluded that the most promising test is the “non-recoverable creep compliance” (Jnr) from the Multiple Stress Creep and Recovery (MSCR) test method, although Zero/Low Shear Viscosity (ZSV/LSV) by creep or oscillation test method can also give good correlations with permanent deformation of bituminous mixtures.

  16. Time dependent viscoelastic rheological response of pure, modified and synthetic bituminous binders

    Science.gov (United States)

    Airey, G. D.; Grenfell, J. R. A.; Apeagyei, A.; Subhy, A.; Lo Presti, D.

    2016-08-01

    Bitumen is a viscoelastic material that exhibits both elastic and viscous components of response and displays both a temperature and time dependent relationship between applied stresses and resultant strains. In addition, as bitumen is responsible for the viscoelastic behaviour of all bituminous materials, it plays a dominant role in defining many of the aspects of asphalt road performance, such as strength and stiffness, permanent deformation and cracking. Although conventional bituminous materials perform satisfactorily in most highway pavement applications, there are situations that require the modification of the binder to enhance the properties of existing asphalt material. The best known form of modification is by means of polymer modification, traditionally used to improve the temperature and time susceptibility of bitumen. Tyre rubber modification is another form using recycled crumb tyre rubber to alter the properties of conventional bitumen. In addition, alternative binders (synthetic polymeric binders as well as renewable, environmental-friendly bio-binders) have entered the bitumen market over the last few years due to concerns over the continued availability of bitumen from current crudes and refinery processes. This paper provides a detailed rheological assessment, under both temperature and time regimes, of a range of conventional, modified and alternative binders in terms of the materials dynamic (oscillatory) viscoelastic response. The rheological results show the improved viscoelastic properties of polymer- and rubber-modified binders in terms of increased complex shear modulus and elastic response, particularly at high temperatures and low frequencies. The synthetic binders were found to demonstrate complex rheological behaviour relative to that seen for conventional bituminous binders.

  17. Biowaste utilization in the process of co-gasification with bituminous coal and lignite

    International Nuclear Information System (INIS)

    Howaniec, Natalia; Smoliński, Adam

    2017-01-01

    Biowaste utilization in co-gasification with bituminous coal and lignite gives the benefits of stable supplies of a primary energy source – coal and utilization of a zero-emission, waste material (i.e. agriculture waste, sewage sludge, etc.) with higher process efficiency and lower negative environmental impact than biomass or coal gasification, respectively. The main focus of the study presented is co-gasification of bituminous coal or lignite with biowaste to hydrogen-rich gas. The experiments were performed in the laboratory scale fixed-bed reactor installation at 700 and 900 °C. The Hierarchical Clustering Analysis complemented with a color map of studied data were applied in the selection of the optimal operating parameters for biowaste utilization in the co-gasification process based on the experimental data of gasification/co-gasification process as well as physical and chemical properties of fuels tested. The experimental results showed that the carbon conversion rate in co-gasification increased with increasing biomass content in a fuel. The total gas volume and hydrogen volume in co-gasification were higher than the values expected based on the results of the gasification process of the fuels analyzed. - Highlights: • Biowaste co-gasification with bituminous coal/lignite to hydrogen-rich gas. • Steam co-gasification in laboratory scale fixed-bed reactor at 700 and 900 °C. • Hierarchical Clustering Analysis complemented with color map of experimental data. • Carbon conversion increase with increasing biomass content. • The highest total gas and hydrogen volume in co-gasification of C-B20 blend at 900C.

  18. Review and environmental impact assessment of green technologies for base courses in bituminous pavements

    International Nuclear Information System (INIS)

    Anthonissen, Joke; Van den bergh, Wim; Braet, Johan

    2016-01-01

    This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

  19. Review and environmental impact assessment of green technologies for base courses in bituminous pavements

    Energy Technology Data Exchange (ETDEWEB)

    Anthonissen, Joke, E-mail: joke.anthonissen@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Van den bergh, Wim, E-mail: wim.vandenbergh@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Braet, Johan, E-mail: johan.braet@uantwerpen.be [Department Engineering Management, Faculty of Applied Economics, University of Antwerp, Prinsstraat 13, 2000 Antwerp (Belgium)

    2016-09-15

    This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

  20. Mineral matter in Spanish bituminous and brown coals. Part 2: mineral matter quantification

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Tarazona, M.R.; Martinez Alonso, A.; Tascon, J.M.D. (Instituto Nacional del Carbon y sus Derivados, Oviedo (Spain))

    1993-05-01

    A number of methods for mineral matter quantification were applied to a set of Spanish coals. Bituminous coals of different rank from the Asturian Central basin and brown coals from Galician basins were studied. Normative analysis was shown to be an adequate procedure for determining the concentrations of individual mineral species. It was found that mineral constituents of Asturian bituminous coals are, in decreasing abundance order, clay minerals (muscovite, kaolinite), quartz and carbonates. In the case of Galician brown coals kaolinite is the most abundant mineral, followed by quartz and pyrite. Extraction with ammonium acetate and oxidation with hydrogen peroxide yielded equivalent values for the concentrations of alkali and alkaline-earth elements bound to organic matter in brown coals. A series of direct and indirect procedures as well as numerical methods for determining the total mineral matter content of coals were compared. Optimum methods for determining the total mineral matter contents of bituminous coals were low-temperature ashing (LTA) and acid demineralisation. The sum of the LTA yield of ammonium acetate-extracted coal and the total concentration of ion-exchanged elements provided the most reliable results for brown coals. Correction formulae from ash yield previously derived for coals from other basins yielded only slightly satisfactory results for the Spanish coals under study. Results obtained evidence the importance of correctly establishing the nature and concentration of clay minerals present in coal. Also, the convenience of carrying out more comprehensive work to unequivocally establish the mineral matter/ash factors for the various types of Spanish coals is suggested. 65 refs., 6 tabs.

  1. Synergistic effect on thermal behavior during co-pyrolysis of lignocellulosic biomass model components blend with bituminous coal.

    Science.gov (United States)

    Wu, Zhiqiang; Wang, Shuzhong; Zhao, Jun; Chen, Lin; Meng, Haiyu

    2014-10-01

    Co-thermochemical conversion of lignocellulosic biomass and coal has been investigated as an effective way to reduce the carbon footprint. Successful evaluating on thermal behavior of the co-pyrolysis is prerequisite for predicting performance and optimizing efficiency of this process. In this paper, pyrolysis and kinetics characteristics of three kinds of lignocellulosic biomass model components (cellulose, hemicellulose, and lignin) blended with a kind of Chinese bituminous coal were explored by thermogravimetric analyzer and Kissinger-Akahira-Sunose method. The results indicated that the addition of model compounds had different synergistic effects on thermal behavior of the bituminous coal. The cellulose showed positive synergistic effects on the thermal decomposition of the coal bituminous coal with lower char yield than calculated value. For hemicellulose and lignin, whether positive or negative synergistic was related to the mixed ratio and temperature range. The distribution of the average activation energy values for the mixtures showed nonadditivity performance. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. A Method to Estimate the Dynamic Displacement and Stress of a Multi-layered Pavement with Bituminous or Concrete Materials

    Directory of Open Access Journals (Sweden)

    Zheng LU

    2014-12-01

    Full Text Available In this research work, a method to estimate the dynamic characteristics of a multilayered pavement with bituminous or concrete materials is proposed. A mechanical model is established to investigate the dynamic displacement and stress of the multi-layered pavement structure. Both the flexible and the rigid pavements, corresponding to bituminous materials and concrete materials, respectively, are studied. The theoretical solutions of the multi-layered pavement structure are deduced considering the compatibility condition at the interface of the structural layers. By introducing FFT (Fast Fourier Transform algorithm, some numerical results are presented. Comparisons of the theoretical and experimental result implied that the proposed method is reasonable in predicting the stress and displacement of a multi-layered pavement with bituminous or concrete materials. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6071

  3. The projects of reducing environmental pollution at the collieries belonging to Petrosani Autonomous Bituminous Coal Administration

    International Nuclear Information System (INIS)

    Arad, V.; Arad, S.; Costinas, B.; Marchis, G.

    1997-01-01

    The economic development in the Jiu Valley, as practised in the mining and processing of bituminous coal, has had a dynamic character without taking into account, however, the harmful impact on the environment. The most severe problem of environmental pollution in the Jiu Valley is that of the pollution of the Jiu River due to the discharge of waste water from the technological processes of mining and processing coal. This paper presents some solutions for reducing this environmental pollution, especially the Jiu water pollution. 1 ref

  4. Investigation of activity release from bituminized intermediate-level waste forms under thermal stresses

    International Nuclear Information System (INIS)

    Kluger, W.; Vejmelka, P.; Koester, R.

    1983-01-01

    To determine the consequences of a fire during fabrication, intermediate storage and transport of bituminized NaNO 3 waste forms, the fractions of plutonium released from the waste forms were assessed. For this purpose, laboratory tests were made with PuO 2 -containing specimens as well as a field test with specimens containing Eu 2 O 3 . By the evaluation of plutonium release in the laboratory and by the determination of the total sodium release and the relative Eu/Na release in the field tests the plutonium release can be deduced from full-scale specimens. The results show that for bituminized waste forms with high NaNO 3 contents (approx. 36 wt%) the average plutonium release obtained in laboratory testing is 15%. In the field tests (IAEA fire test conditions) an average Eu release of 8% was found. These results justify the statement that also for waste forms in open 175 L drum inserts a maximum plutonium release of about 15% can be expected. From the time-dependence of Eu/Na release in the field tests an induction period of 15-20 minutes between the start of testing and the first Na/Eu release can be derived. The maximum differential Na/Eu release occurs after a test period of 45 to 60 minutes duration and after 90 to 105 minutes (tests K2 and K4, respectively); after that time also the highest temperatures in the products are measured. The release values were determined for products in open 175 L drum inserts which in this form are not eligible for intermediate and ultimate storage. For bituminized waste forms in concrete packages (lost concrete shieldings) a delayed increase in temperature to only 70-80 deg. C takes place (4-5 hours after extinction of the fire) if the fire lasts 45 minutes. The concrete package remains intact under test conditions. This means that activity release from bituminized waste forms packaged in this way can be ruled out in the case under consideration. (author)

  5. Assessment of the Remaining Life of Bituminous Layers in Road Pavements

    Directory of Open Access Journals (Sweden)

    Kálmán Adorjányi

    2017-02-01

    Full Text Available In this paper, a mechanistic-empirical approach is presented for the assessment of bearing capacity condition of asphalt pavement layers by Falling Weight Deflectometer measurements and laboratory fatigue tests. The bearing capacity condition ratio was determined using past traffic data and the remaining fatigue life which was determined from multilayer pavement response model. The traffic growth rate was taken into account with finite arithmetic and geometric progressions. Fatigue resistance of layers’ bituminous materials was obtained with indirect tensile fatigue tests. Deduct curve of condition scores was derived with Weibull distribution.

  6. Fixed-bed gasification research using US coals. Volume 13. Gasification of Blind Canyon bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Thimsen, D.; Maurer, R.E.; Pooler, A.R.; Pui, D.; Liu, B.; Kittelson, D.

    1985-05-01

    A single-staged, fixed-bed Wellman-Galusha gasifier coupled with a hot, raw gas combustion system and scrubber has been used to gasify numerous coals from throughout the United States. The gasification test program is organized as a cooperative effort by private industrial participants and governmental agencies. The consortium of participants is organized under the Mining and Industrial Fuel Gas (MIFGa) Group. This report is the thirteenth volume in a series of reports describing the atmospheric pressure, fixed-bed gasification of US coals. This specific report describes the gasification of Blind Canyon bituminous coal, from July 31, 1984 to August 11, 1984. 6 refs., 22 figs., 20 tabs.

  7. Testing of bituminized ion-exchange resin waste products from a nuclear power plant

    International Nuclear Information System (INIS)

    Muurinen, A.K.; Vuorinen, U.S.

    Testing methods are described and preliminary results presented for the bituminized waste products from TVO nuclear power plant. Radiation effects on the physical and chemical characteristics of the waste product and a pure bitumen sample were studied using an external 60 Co gamma source. Results of the postirradiation study show that the relative density decreases for both the waste products and the bitumen. Softening points rise for waste products but drop for bitumen. Breaking point of the powder resin waste product drops; in the granular resin waste product it rises on the surface and slightly decreases or does not significantly change at the bottom. For bitumen the breaking point rises

  8. Biomarker geochemistry of bituminous shale sequence and crude oil in the Ereǧli-Bor Basin (Konya-Niǧde), Central Anatolia, Turkey

    Science.gov (United States)

    Kara-Gulbay, Reyhan; Erdogan, Mert; Korkmaz, Sadettin; Kadinkiz, Gökhan

    2016-04-01

    In the Ereǧli-Bor Basin (Konya-Niǧde), Central Anatolia, bituminous shale sequence with thickness ranging between 72 and 160 m occurs in lacustrine deposits of Upper Miocene-Pliocene age. The live oil has also been observed in this bituminous shale sequence. Rock-Eval/TOC, GC and GC-MS analyses were conducted on selected bituminous shale samples from four borehole (key-12/1, key-12/2, key-12/3 key-12/4) and one crude oil sample from a borehole (key-12/2) in the basin. In this study, organic matter type, maturity and depositional environment of bituminous shale are evaluated and the origin of crude oil is determined by the bituminous shale-crude oil correlation. The total organic carbon (TOC) values of the bituminous shale samples range from 1.21-13.98 wt% with an average TOC value of 4.75wt%. The bituminous shale sequence is characterized by high HI (127-662 mg HC/g TOC) and low OI (7-50 mgCO2/TOC). Tmax varies from 332-419ᵒC. Very low Pr/Ph ratios of bituminous shale (0.09-0.22) are indicative of anoxic depositional conditions. C27 is dominate sterane for bituminous shale and crude oil samples with C27>C29>C28. Normal steranes are more dominant compare to iso- and diasteranes. Ouite high sterane/hopane ratios (1.14-2.70) indicate dominant algal organic matter input for bituminous shale and source rock of crude oil. C31R/hopane ratio for bituminous shale and crude oil samples are very low (0.09-0.13) and these ratio show a lacustrine depositional envirronment for bituminous shale and source rock of crude oil. Sterane and terpane distributions of bituminous shale and crude oil are very similar. A very good correlation in terms of biomarker between bituminous shale and crude oil samples indicate that source rock of crude oil is bituminous shale. The 22S/(22R + 22S) C32 homohopane ratios of bituminous shale and crude oil samples are found to be 0.56 and 0.61, indicating that homohopane isomerization has attained equilibrium and bituminous shale and crude oil are

  9. Feasibility study of producing lump fuel using oil-bituminous sands

    Energy Technology Data Exchange (ETDEWEB)

    Moldybaev, A.B.; Ermagambetov, B.T.; Mamraeva, K.M.; Shin, R.G.; Bakirova, R.K. (Institut Organicheskogo Sinteza i Uglekhimii AN KazSSR (USSR))

    1991-04-01

    Describes production of lump fuel by briquetting and coking different mixtures of non-caking coal with coal preparation sludge and bitumen extracted from oil sands. The coal used was from the Shubarkol'sk coal deposit (USSR); the sludge was from the Saburkhanskaya preparation plant. Properties and composition of oil-bituminous sands and of bitumen to be used as binder are given. Technological details of the briquetting and coking processes are provided. Results show that briquets produced from mixtures of coal and oil-bituminous sands can only be used as a high-ash lump fuel, which cannot be further processed into semicoke. Experiments were carried out briquetting coal or coke, sludge and 6-8% bitumen extracted from the sands, varying coal or coke grain fractions and composition of the mixture. An increased briquet strength was found after using the vacuum-distilled 300-350 C bitumen fraction. Briquets from this non-caking coal with bitumen binder are regarded as ecologically clean fuel. 5 refs.

  10. THE HISTORY OF EXPLORATION AND EXPLOITATION OF BITUMINOUS AND KEROGENOUS DEPOSITS IN CROATIA

    Directory of Open Access Journals (Sweden)

    Berislav Šebečić

    1995-12-01

    Full Text Available It is assumed thal the first known sedimens of natural bitumen or asphalt in coastal Croatia were exploited as the early moddle ages. Yet authenticated written documents about Vinišće near Trogir derive from no earlier than 1628, about Vrgorac/Paklina from only 1753. By the end of the 18th century, many deposits were discovered in Dalmatia, but it was Škrip on the Island of Brač and Suhi Dolac that were important. The earliest known deposits and occurrences of kerogenous rocks, or bituminous or oil shales, are mentioned as stone or fossil coal in Sovinjak, in the upper course of the River Mirna, and in Rebići in Istria; near Sinj, Slivno not far from the River Neretva, Mirta and near Nerežišće on the Island uf Brač. All if these were well known and described in 1804, while Sovinjak was mentioned in the 16th century. In the article, some of new information derived from mining and geological research into bituminous and kerogenous sediments and deposits are provided (the paper is published in Croatian.

  11. Isotopic variations in the nitrogen of natural humic and bituminous organic substances

    International Nuclear Information System (INIS)

    Stiehl, G.; Lehmann, M.

    1980-01-01

    delta 15 N-values and nitrogen contents of a series of humic and bituminous organic sediments of different ranks were determined. The change of the isotopic abundance of nitrogen was investigated during heating in model experiments, using a gas flame coal. In the case of humic carbon coals the relative nitrogen contents vary from 0.8 to 1.4% and the delta 15 N-values from + 3.5 to + 6.3 parts per thousand increasing from the brown coal to anthracite ranks. During the coalification process both the delta 15 N-values and the relative nitrogen contents do not vary continuously with the rank, but pass through maxima and minima. Model experiments using a gas flame coal show the same trend. Nitrogen with delta 15 N-values of + 2.8 or -7 parts per thousand was released in pyrolysis experiments, applying a gas flame coal and a steam coal at temperatures of 650 and 1000 0 C, respectively. The investigated bituminous sediments yielded relative amounts of 0.1 to 0.8% with delta 15 N-values of + 4.2 to + 10.7 parts per thousand. The obtained results are discussed with respect to the elucidation of nitrogen genesis in natural gas deposits. (author)

  12. Assessing radioactive concentrates and waste vapor condensate in solidifying radioactive wastes by bituminization

    International Nuclear Information System (INIS)

    Tibensky, L.; Krejci, F.; Breza, M.; Timulak, J.; Hladky, E.

    1986-01-01

    A brief overview is presented of chemical and radiochemical methods used in the world for the analysis of the concentrate of liquid radioactive wastes from nuclear power plants destined for bituminization. Most methods are also suitable for an analysis of the condensate of waste vapors produced in bituminization. The methods of analysis of the radioactive concentrate from the V-1 nuclear power plant in Jaslovske Bohunice and of the waste vapors condensate were developed and tested in practice. Gross gamma activity was measured using a well-type Na(Tl) scintillation detector, the content of radionuclides was determined using semiconductor Ge(Li) spectrometry. The concentration of boric acid in the concentrate was determined by titration with mannite; in the condensate, using spectrophotometry with curcumine. The content of nitrates in both the concentrate and the condensate was determined spectrophotometrically using salicylic acid, the content of nitrites was determined by spectrophotometry using sulfanilic acid and α-naphthylamine. Carbonates and chlorides were determined by titration, sodium and potassium by flame photometry. The content of organic acids was measured by gravimetry of extracted methyl esters, the content of surfactants by spectrophotometry. Infrared spectrophotometry was used in determining hydrocarbons in the waste vapor condensate. The measured value range and the measurement errors are shown for each method. (A.K.)

  13. Reuse of bituminous pavements: A mini-review of research, regulations and modelling.

    Science.gov (United States)

    Anthonissen, Joke; Van den Bergh, Wim; Braet, Johan

    2017-04-01

    Bituminous pavement can be recycled - even multiple times - by reusing it in new bituminous mixtures. If the mechanical properties of the binder get worse, this reclaimed asphalt is often used in the sub-structure of the road. Apparently, up till now, no end-of-life phase exists for the material. Actually, defining the end-of-life and the end-of-waste stage of a material is important for life cycle assessment modelling. Various standards and scientific studies on modelling life cycle assessment are known, but the crucial stages are not yet defined for reclaimed asphalt pavement. Unlike for iron, steel and aluminium scrap, at this moment, no legislative end-of-waste criteria for aggregates are formulated by the European Commission. More research is necessary in order to develop valuable end-of-life criteria for aggregates. This contribution is a mini-review article of the current regulations, standards and studies concerning end-of-life and end-of-waste of reclaimed asphalt pavement. The existing methodology in order to define end-of-waste criteria, a case study on aggregates and the argumentation used in finished legislative criteria are the basis to clarify some modelling issues for reclaimed asphalt material. Hence, this contribution elucidates the assignment of process environmental impacts to a life cycle stage as defined by EN15804, that is, end-of-life stage (C) and the supplementary information Module D with benefits and loads beyond the system boundary.

  14. Application of the cementitious grouts on stability and durability of semi flexible bituminous mixtures

    Science.gov (United States)

    Karami, Muhammad

    2017-11-01

    This paper describes the results of laboratory test for a high durability semi flexible bituminous mixtures (SFBM). The SFBM consists of an open asphalt structure where a high strength mortar is penetrated into the air voids of the bituminous mixtures. The SFBM combines the cement concrete's strength and the asphalt material flexibility. The objective of this study is to involve in the determination of stability and durability of SFBM by located the position of the specimen on an exposed area for 7, 90, 180 and 240 days. The performance of the SFBM was assessed using Marshall and wheel tracking apparatus. Total 18 specimens were prepared and examined for both of test. The Marshall specimens were cylindrical with dimension of 10.16 cm in diameter and 6.35 cm in high. For wheel tracking test, the specimens consisted of slabs with dimension of 30 cm in length, 30 cm in width and 5 cm in height. The results indicated that the first durability index and second durability index increased significantly. For Marshall test, the first and second durability index increased about 0.9% per day and 52.3%, respectively. However, for wheel tracking test, the first and second durability index increased about 1.9% per day and 119%, respectively.

  15. INVESTIGATION ON UTILITY OF PLASTIC WASTE AS AN ADDITIVE FOR BITUMINOUS CONCRETE USING WET PROCESS OF MIXING

    Directory of Open Access Journals (Sweden)

    Anurag Virendra Tiwari

    2017-12-01

    Full Text Available Purpose. Plastic waste has become a major environmental issue of concern due to its exponential growth due to rapid urbanization. The paper investigates utility of plastic waste as an additive for bituminous concrete using wet process of mixing. Methodology. The methodology for the present paper has been designed with complex research consisting of Marshall mix design of the bituminous mix added with plastic waste for modifying bitumen using wet process of mixing, performing the tests on the samples and analyzing the results in the form of table and figures. In the present paper LDPE and HDPE type of plastic waste are used to modify the bitumen. Finding. The results show that addition of 6 percent of bitumen improves the Marshall properties of the mix. Use of plastic to modify the bitumen not only makes the road surface more durable but also it is an eco-friendly way of proper disposal of plastic waste. Originality. The processes used for mixing the plastic waste to the bitumen are dry process and wet process. Dry process of mixing the plastic waste to the bituminous mix is most common and lot of study is carried out on its application. In the present paper wet process of mixing has not yet been studied much. Practical Value. The practical application of utilizing the plastic waste to modify bitumen in the bituminous mix improves the stability values resulting in the more durable road surface. Also the method ensures the proper disposal of plastic waste in eco-friendly way.

  16. Appropriate use of locally available materials in concrete, bituminous surfacings and layerworks for roads in rural areas

    CSIR Research Space (South Africa)

    Paige-Green, P

    2009-06-17

    Full Text Available and durability of the concrete and probably to increase the shrinkage. Bituminous surfacings are currently tightly specified and comparison with other countries indicates that certain areas of relaxation are possible. These are mostly with respect to the grading...

  17. Mechanical properties of hot bituminous mixes manufactured with recycled aggregate of Silestone® waste

    Directory of Open Access Journals (Sweden)

    Rubio, M. C.

    2011-03-01

    Full Text Available This article presents the results of a research project which analyzes the viability of incorporating waste material from decorative quartz solid surfacing in the manufacture of hot bituminous mixes. For this purpose, various bituminous mixes were manufactured with waste aggregate in different percentage. A set of tests were carried out that permitted the characterization of the mechanical behavior of these mixes. The results of these tests were similar to the results obtained when conventional mixes made from virgin quarry aggregate were tested. The results for moisture sensitivity as well as for wheel track rutting on mixes showed the optimal performance of this waste material even under very demanding traffic conditions. Laboratory studies showed that the use of this waste material in the manufacture of bituminous mixes is technically viable and can provide high-quality recycled aggregates at a very low cost, which can be used in the pavement of road.

    Este artículo muestra los resultados de un proyecto de investigación que tiene por objeto analizar la viabilidad de incorporación de residuos procedentes de piedra decorativa en la fabricación de mezclas bituminosas en caliente. Para ello se fabricaron mezclas con áridos reciclados de residuos procedentes de piedra decorativa en distintos porcentajes, realizando un conjunto de ensayos que posibilitaron caracterizar el comportamiento mecánico de dichas mezclas. Los resultados obtenidos fueron similares a los de las mezclas convencionales fabricadas con áridos vírgenes procedentes de cantera. Los valores de resistencia conservada ante la acción del agua y deformación en pista, pusieron de manifiesto la aptitud del residuo incluso ante las condiciones de tráfico más exigentes. Los trabajos realizados en el laboratorio indican que la utilización del residuo en la fabricación de mezclas bituminosas es técnicamente viable, pudiendo obtenerse áridos reciclados de gran calidad y

  18. Comparative study of test methods for bituminized and other low- and medium-level solidified waste materials

    International Nuclear Information System (INIS)

    Brodersen, K.; Mose Pedersen, B.; Vinther, A.

    1983-12-01

    Various aspects of the behaviour of bituminized or cemented simulated low- or medium-level radioactive waste in contact with water or salt solutions have been investigated. The solubility (approximately 0.5%) and the diffusion coefficient (approximately 5.10 -8 cm 2 /sec) determining transort of water in pure bitumen have been measured for Mexphalte 40/50 at room temperature. A weighing method has been used to study water uptake and swelling of bituminized sodium nitrate, sodium sulphate or cation-exchange resin. The swelling of samples in contact with water was in some cases very pronounced. In strong salt solutions the tendency to swell is much less. The particle size of the embedded waste material is an important parameter. Thermal pre-treatment of cation-exchange resin before bituminization does not seem to improve the quality of the final product. The interaction between bituminized-exchange resin and concrete barrier materials has been studied. Microbial degradation of bitumen and bituminized waste under aerobic conditions has been investigated. It is probably of minor importance as far as leaching is concerned. A method for measuring leaching from a plane surface of cemented waste has been developed. The method avoids the problem of cracks between the sample and the container. Leaching from cemented sodium nitrate or sulphate was investigated. Absorption of CO 2 from the atmosphere was found to have only minor effect on Cs- and Na-leaching but gave a pronounced decrease in Ca-leaching. The use of silica-fume as an additive to cemented sodium nitrate decreased the leach rate by a factor 4. (author)

  19. Bituminization of simulated waste, spent resins, evaporator concentrates and animal ashes by extrusion process

    International Nuclear Information System (INIS)

    Grosche Filho, C.E.; Chandra, U.

    1987-01-01

    The results of the study of bituminization of simulated radwaste - spennt ion-exchange resins, borate evaporator/concentrates and animal ashes, are presented and discussed. Distilled and oxidizer bitumen were used. Characterization of the crude material and simulated wastes-bitumen mixtures of varying weigt composition (30, 40, 50, 60% by weight of dry waste material) was carried out. The asphaltene and parafin contents in the bitumens were also determined. Some additives and were used with an aim to improve the characteristcs of solidified wastes. For leaching studies, granular ion-exchange resins were with Cs - 134 and mixtures of resin-bitumen were prepared. The leaching studies were executed using the IAEA recommendation and the ISO method. A conventional screw-extruder, common in plastic industry, was used determine operational parameters and process difficulties. Mixtures of resin-bitumen and evaporator concentrate-bitumen obtained from differents operational conditions were characterized. (Author) [pt

  20. Influence of Antioxidant-Enhanced Polymers in Bitumen Rheology and Bituminous Concrete Mixtures Mechanical Performance

    Directory of Open Access Journals (Sweden)

    Samer Dessouky

    2015-01-01

    Full Text Available This paper evaluates the effect of polymer enhancement with antioxidant in the rheological properties of bitumen and mechanical properties of bituminous concrete mixture (BCM. In this study, two antioxidant-enhanced polymers were utilized in mitigating bitumen hardening due to aging. The rheological testing consists of temperature sweep using Dynamic Shear Rheometer at various aging conditions. Critical stiffness temperature data from the sweep test suggested that enhanced polymer exhibits less long-term hardening and brittleness compared to standard polymer. The mechanical testing consists of dynamic modulus, indirect tensile, flow number, and beam fatigue tests on BCM exposed to short-term aging. Hamburg wheel tracking test was also performed to assess moisture-damage susceptibility. It is found that the enhanced-polymer BCM exhibited higher modulus, higher tensile strength ratio, improved rutting resistance, lower moisture-damage susceptibility, and slightly increased fatigue life as compared to standard-polymer BCM.

  1. Study of Rheological Properties of Bituminous Binders in Middle and High Temperatures

    Directory of Open Access Journals (Sweden)

    Remišová Eva

    2016-05-01

    Full Text Available The bitumen binders in road pavements are exposed traffic loading effect at different climatic conditions. A resistance to these stresses depends on bitumen properties as well. The paper presents rheological properties (G*, δ, ν* determined and compared for four bituminous binders (unmodified and polymer modified bitumen at temperature 46 – 60 (80 °C and dynamic viscosity at temperature 130 – 190 °C (Brookfield viscometer. On the basis of viscosity results it is possible to set optimal production and compaction temperatures. Elastic and viscous behavior of binder in the middle temperature is determined in rheometers. The higher value of complex modulus, the stiffer bitumen binder is able to resist deformation. The greater content of elastic components (e.g. polymer in bitumen varies mainly elastic-viscous properties of primary bitumen.

  2. Development of advanced air-blown entrained-flow two-stage bituminous coal IGCC gasifier

    Directory of Open Access Journals (Sweden)

    Abaimov Nikolay A.

    2017-01-01

    Full Text Available Integrated gasification combined cycle (IGCC technology has two main advantages: high efficiency, and low levels of harmful emissions. Key element of IGCC is gasifier, which converts solid fuel into a combustible synthesis gas. One of the most promising gasifiers is air-blown entrained-flow two-stage bituminous coal gasifier developed by Mitsubishi Heavy Industries (MHI. The most obvious way to develop advanced gasifier is improvement of commercial-scale 1700 t/d MHI gasifier using the computational fluid dynamics (CFD method. Modernization of commercial-scale 1700 t/d MHI gasifier is made by changing the regime parameters in order to improve its cold gas efficiency (CGE and environmental performance, namely H2/CO ratio. The first change is supply of high temperature (900°C steam in gasifier second stage. And the second change is additional heating of blast air to 900°C.

  3. Development of advanced air-blown entrained-flow two-stage bituminous coal IGCC gasifier

    Science.gov (United States)

    Abaimov, Nikolay A.; Ryzhkov, Alexander F.

    2017-10-01

    Integrated gasification combined cycle (IGCC) technology has two main advantages: high efficiency, and low levels of harmful emissions. Key element of IGCC is gasifier, which converts solid fuel into a combustible synthesis gas. One of the most promising gasifiers is air-blown entrained-flow two-stage bituminous coal gasifier developed by Mitsubishi Heavy Industries (MHI). The most obvious way to develop advanced gasifier is improvement of commercial-scale 1700 t/d MHI gasifier using the computational fluid dynamics (CFD) method. Modernization of commercial-scale 1700 t/d MHI gasifier is made by changing the regime parameters in order to improve its cold gas efficiency (CGE) and environmental performance, namely H2/CO ratio. The first change is supply of high temperature (900°C) steam in gasifier second stage. And the second change is additional heating of blast air to 900°C.

  4. Fixed-bed gasification research using US coals. Volume 9. Gasification of Elkhorn bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Thimsen, D.; Maurer, R.E.; Pooler, A.R.; Pui, D.; Liu, B.; Kittelson, D.

    1985-05-01

    A single-staged, fixed-bed Wellman-Galusha gasifier coupled with a hot, raw gas combustion system and scrubber has been used to gasify numerous coals from throughout the United States. The gasification test program is organized as a cooperative effort by private industrial participants and governmental agencies. The consortium of participants is organized under the Mining and Industrial Fuel Gas (MIFGa) group. This report is the ninth volume in a series of reports describing the atmospheric pressure, fixed-bed gasification of US coals. This specific report describes the gasification of Elkhorn bituminous coal. The period of gasificastion test was September 13 to October 12, 1983. 9 refs., 24 figs., 35 tabs.

  5. Application of laser microprobe (LAMMA 1000) to "fingerprinting" of coal constituents in bituminous coal

    Science.gov (United States)

    Lyons, P.C.; Hercules, D.M.; Morelli, J.J.; Sellers, G.A.; Mattern, D.; Thompson-Rizer, C. L.; Brown, F.W.; Millay, M.A.

    1987-01-01

    A laser microprobe (LAMMA-1000) microchemical analysis of vitrinites of different morphologies but similar reflectances within the same bituminous coal bed indicates distinct "fingerprint" spectra. The banded form of vitrinite contains Li, Ti, Ba, Sr, F, and Cl which were not detected in the nonbanded vitrinite. These differences may indicate a different plant source or the introduction of these elements from fluids mobilized during diagenesis. The nonbanded vitrinite (called corpocollinite), which was contained in a pyrite coal-ball seed fern permineralization of Myeloxylon, may have been protected from influx of these elements due to entrapment by pyrite during an early peat stage. An ion at M/Z 65, which is characteristic of the banded vitrinite, may indicate C5H5+ and, perhaps a difference in the chemical structure of the two vitrinites. These results demonstrate that "fingerprint" spectra can be obtained from vitrinite macerals by LAMMA and that these "fingerprints" have genetic implications. ?? 1987.

  6. Distribution of inorganic and organic substances in the hydrocyclone separated Slovak sub-bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Anton Zubrik; Slavomir Hredzak; Ludmila Turcaniova; Michal Lovas; Ingo Bergmann; Klaus Dieter Becker; Maria Lukcova; Vladimir Sepelak [Slovak Academy of Sciences, Kosice (Slovakia). Institute of Geotechnics

    2010-08-15

    A low-rank Slovak sub-bituminous coal from the Handlova deposit was physically treated by washing in a water-only cyclone with the goal to find the separation effect for inorganic (mainly Fe-bearing minerals) and organic substances (humic acids, diterpanes). A high-quality coal product with the ash content in the dry matter of 9.02% and carbon content of C{sup d} = 68.12% at a mass yield of 29.51% was obtained using the water-only cyclone processing. At first, the physically treated coal samples were detailed characterized by XRD, {sup 57}Fe Moessbauer spectroscopy, FT-IR and HR-TEM. In addition to non-crystalline organic coal components, inorganic compounds belonging to silicate minerals (kaolinite, muscovite and quartz) as well as to Fe-bearing sulphide minerals (pyrite) were identified in the sub-bituminous coal by XRD. {sup 57}Fe Moessbauer spectroscopy detected the presence of iron carbonate (siderite), iron-containing clay mineral and two sulphur-containing minerals (pyrite, jarosite) in the untreated coal. On the other hand, only one Fe-bearing mineral, (pyrite) was found in the washed coal. Effect of the physical separation is also demonstrated in FT-IR spectra, where the peak at 1040 cm{sup -1} representing the silicate component in the untreated sample is not detectable in the washed coal sample. Presence of extractive organic substances, i.e. humic acids and tetracyclic diterpane (16a(H)-phyllocladane), in the hydrocyclone products is also evidenced. It was confirmed that the isolated diterpenoic compound is attendant in the washed product with the lowest ash content and it is assimilated with the organic part of coal. Surprisingly, humic acids were found in the highest concentration in the slurry that has the highest content of ash (63.14%). 54 refs., 8 figs., 5 tabs.

  7. The Structure of Sandstones in Productive Horizons of the Permian Bituminous Deposits of Tatarstan (Russia

    Directory of Open Access Journals (Sweden)

    R.R. Khasanov

    2017-03-01

    Full Text Available The features of sandstones in productive horizons of the Permian bituminous deposits of Tatarstan (Russia have been considered. The composition and internal structure of sandstones have been studied by optical microscopy, electron paramagnetic resonance (EPR, and electron microscopy, as well as using a number of physical and chemical methods to solve special problems. The investigated sandstones belong to the greywacke group. The clastic material of sandstones contains grains of feldspar, quartz, mica, and particles of volcanic rocks. The nature and composition of cement are important parameters that determine the filtration-capacity properties of sedimentary rocks. Bituminous deposits are characterized by vertical zoning, which is expressed in the alternation of sites with varying degrees of cementation of rocks. Atten-tion has been also paid to post-sedimentation processes, such as pyritization and calcification. Pyrite forms rare xenomorphic isometric grains. The formation of pyrite occurs in diagenesis and is associated with the processes of biogenic sulfate reduction. The source of calcium for the crystallization of dispersed cal-cite in the porous space of sandstones is the underground waters of red-colored Ufimian deposits characterized by the alkaline properties favorable for calcium migration. According to the data of X-ray computed tomography, the internal space of the studied rocks is not homogeneous and represented by a system of communicated and isolated pores. In the studied samples, two types of organic matter differing in organic radicals have been detected. The first type is an organic substance of coal origin. The second type of organic matter belongs to the oil origin and refers to bitumens in its properties. The presence of a significant percentage of asphaltenes in the bitumen composition indicates the destruction of the oil substance in the near-surface conditions.

  8. Using proximate analysis to characterize airborne dust generation from bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Page, S.J.; Organiscak, J.A. [NIOSH, Pittsburgh, PA (United States). Pittsburgh Research Lab.

    2002-06-01

    Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals to investigate the various factors influencing airborne respirable dust generation. Bituminous coal samples from 8 mines (5 U.S. and 3 Polish) were uniformly prepared and processed through a double roll crusher located in a low air velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific quantity of airborne respirable dust generated. A combination of factors is associated with the generation of airborne respirable dust. One factor involved is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics. However, since coals of high moist fuel ratio (high rank) are generally more extensively cleated, it is suggested that the degree of cleating is directly responsible for the quantity of respirable-sized particles produced in the crushed product material for eastern U.S. coals. This is implied by the relationship of ash content and at least one mineral constituent (pyrite, determined from pyritic sulfur analysis) to the percentage of airborne respirable dust. A clear delineation of coals, based on well-known proximate analysis characteristics, that generate the most respirable dust appears to be possible. It was also shown that the dust-generating characteristics of coals could be reasonably described by both the moist fuel ratio and the Hardgrove Grindability Index (HGI). These results show a clear distinction between eastern and western U.S. coals. However, no consistent distinction for Polish coal was observed.

  9. DEPOSITIONAL ENVIRONMENT AND ORGANIC GEOCHEMICAL CHARACTERISTICS OF LOWER EOCENE BITUMINOUS ROCKS, IN THE KÜRNÜÇ/GÖYNÜK-BOLU AREA

    Directory of Open Access Journals (Sweden)

    Ali SARI

    2016-12-01

    Full Text Available In this study, dark gray and dark brown colored, organic-carbon rich bituminous rocks (bituminous marl and bituminous shale exposing around the Kürnüç area (Göynük, Bolu are investigated by means of or- ganic geochemical characteristics. In this respect, rock lithologies, depositional environments, rock source potential, kerogen and organic maturity types and hydrocarbon generation potentials of bituminous rocks were determined. For this reason, pyrolysis (Rock Eval–VI analysis, gas chromatography (GC and gas chromatography-mass spectrometer (GC-MS analyses were carried out. In addition, spore color index (SCI was determined with organic petrographic method and stable carbon analysis (δ13C of the samples were also conducted. Lithology of the studied samples is of clastic source and the depositional environ- ment is a lagoon with a partial connection to the sea. In bituminous rocks with excellent source rock potential TOC values are in the range of 2.52-8.38 wt % (average 6.08 wt %. With the exception of two samples (Type II kerogen type of all samples is Type I. According to pyrolysis, GC and GC-MS organic maturity results, all the samples are in immature stage. Organic geochemical data indicate that bituminous rocks have an excellent oil generation potential and there is no organic contamination.

  10. Processing of a Silesian bituminous coal tar mixture at 600 atm to heavy oil excess in a 10-liter oven

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer, H.

    1942-10-28

    An analysis was made of a bituminous coal tar mixture for consideration as raw material for Blechhammer. A breakdown of the composition and yield charts is provided. A table compared it to a coke tar pitch and a bituminous tar mixture from a different carbonization process and its yields were approximately between the yield values of these two. Although the sludge extraction produced sufficient yields in the experiment, the yields would not be as good within full-scale industry. A day by day progress description of the experimentation is provided including all operational details. The experimental results and the pros and cons are summarized briefly. Fifteen tables of data provide analysis of all the elements tested.

  11. Fuel-oils from co-pyrolysis of scrap tyres with coal and a bituminous waste. Influence of oven configuration

    OpenAIRE

    Acevedo Muñoz, Beatriz; Barriocanal Rueda, Carmen

    2014-01-01

    Two wastes from the tyre recycling industry – the fibers used as reinforcing material and tyre crumbs – were pyrolyzed in two ovens of different configuration. Blends with a low rank coal and a bituminous waste were also prepared to modify the composition of the oils obtained from the pyrolysis of the tyre wastes. Elemental analysis, calorific value, Fourier transform infrared spectroscopy (FTIR) and gas chromatography were used to determine the oil composition. A comparative study taking int...

  12. Catalytic Two-Stage Liquefaction (CTSL) process bench studies with bituminous coal. Final report, [October 1, 1988--December 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Comolli, A.G.; Johanson, E.S.; Karolkiewicz, W.F.; Lee, L.K.; Stalzer, R.H.; Smith, T.O.

    1993-03-01

    Reported herein are the details and results of Laboratory and Bench-Scale experiments using bituminous coal concluded at Hydrocarbon Research, Inc., under DOE contract during the period October 1, 1988 to December 31, 1992. The work described is primarily concerned with the application of coal cleaning methods and solids separation methods to the Catalytic Two-Stage Liquefaction (CTSL) Process. Additionally a predispersed catalyst was evaluated in a thermal/catalytic configuration, and an alternative nickel molybdenum catalyst was evaluated for the CTSL process. Three coals were evaluated in this program: Bituminous Illinois No. 6 Burning Star and Sub-bituminous Wyoming Black Thunder and New Mexico McKinley Mine seams. The results from a total of 16 bench-scale runs are reported and analyzed in detail. The tests involving the Illinois coal are reported herein, and the tests involving the Wyoming and New Mexico coals are described in Topical Report No. 1. On the laboratory scale, microautoclave tests evaluating coal, start-up oils, catalysts, thermal treatment, CO{sub 2} addition and sulfur compound effects are reported in Topical Report No. 3. Other microautoclave tests, such as tests on rejuvenated catalyst, coker liquids, and cleaned coals, are described in the Bench Run sections to which they refer. The microautoclave tests conducted for modelling the CTSL process are described in the CTSL Modelling section of Topical Report No. 3 under this contract.

  13. Utilization of Waste Clay from Boron Production in Bituminous Geosynthetic Barrier (GBR-B Production as Landfill Liner

    Directory of Open Access Journals (Sweden)

    Müfide Banar

    2016-01-01

    Full Text Available Bituminous geomembranes, one type of geosynthetics, include a hot bituminous mixture with mineral filler and reinforcement. In this study, boron production waste clay (CW was used as filler to produce a geosynthetic barrier with bentonite, waste tire, and bitumen. Bentonite and waste tires were used as auxiliary fillers and bitumen as the binder. CW/bitumen, CW/bentonite/bitumen, and CW/waste tire/bitumen mixtures were prepared by using a laboratory mixer at 100°C. Hot mixtures were extruded into strips by using a lab-scale corotating twin screw extruder (L/D: 40 followed by die casting (2 mm × 100 mm. Glass fleece or nonwoven polyester was used as reinforcement material and while die casting, both sides of the reinforcement materials were covered with bituminous mixture. Thickness, mass per unit area, tensile strength, elongation at yield, and hydraulic conductivity were used to characterize the geomembranes. Among all geomembranes, nonwoven polyester covered with 30% bitumen-70% boron waste clay mixture (PK-BTM30CW70 was found to be the most promising in terms of structure and mechanical behaviour. After that, consequences of its exposure to distilled water (DW, municipal solid waste landfill leachate (L-MSW, and hazardous waste landfill leachate (L-HW were examined to use for an innovative impermeable liner on solid waste landfills.

  14. Potential of water-washing of rape straw on thermal properties and interactions during co-combustion with bituminous coal.

    Science.gov (United States)

    Ma, Qiulin; Han, Lujia; Huang, Guangqun

    2017-06-01

    The aim of this work was to study the thermal properties and interactions during co-combustion of rape straw (RS) before and after water-washing with bituminous coal. A series of experiments was conducted to investigate the properties and interactions during co-combustion of RS with bituminous coal (at 10, 20, 40 and 60% RS). The feasibility and potential of water-washing as an RS pre-treatment was also explored. Reactivity and the amount of heat released followed a quadratic trend, while changes to the degree of interactions between the fuels conformed to a cosine curve. Water-washing increased the ignition and burn-out temperatures and slightly decreased reactivity. Demineralization negatively affected the previously synergistic co-firing relationship, nevertheless, the amount of heat released increased by 10.28% and the average activation energy (146kJ/mol) was lower than that of the unwashed blend (186kJ/mol). Overall, water-washing of RS could prove a useful pre-treatment before co-combustion with bituminous coal. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Assessment of an Impulse GPR Antenna Abilities in Investigation of Transversal Cracks of the Bituminous Pavement

    Science.gov (United States)

    Krysiński, L.; Sudyka, J.

    2012-04-01

    Ground Penetrating Radar (GPR) technique is commonly used for detection of internal singularities of construction structure. The method is particularly efficient in the case of linear horizontal objects when profile scanning is being performed in the direction perpendicular to object elongation and polarization of the electric field is parallel to the elongation. Then the singular object manifests itself in the echogram as a scattering hyperbola. Similar response is generated by an object having shape close to a vertical half plane with horizontal edge, when the edge acts like the scattering linear object. The use of GPR technique for investigation of transversal cracks in the bituminous pavement would seem to be promising, but numerous paradoxes occur just at the beginning tests. Even well visible cracks of more than ten millimeters thickness doesn't generate noticeable GPR response, while thinner ones sometimes can produce strong response but in the deeper interior of the pavement. Thus arise a more general question: what the GPR technique can tell us about the cracks? Trying to study this problem some laboratory tests were performed to estimate efficiency of signal generation by structures simulating idealized cracks' shapes. Next long-term (several years) visual observation and repeated GPR scanning was performed on the three road sections (each one of several hundred meters length) with heavy traffic, where ongoing cracking process occurs. The preliminary measurements were directed to obtain the proper way of scanning. The main aim of the analysis was to find GPR characteristics of cracks that can be noticed on echograms. It was performed by detailed correlation of the visually observed cracks position with echograms using decimeter precision. These efforts provided a list of diagnostic GPR characteristics of cracks and some provisional scale of their intensity. In several cases the cracks were probed by drillings to recognize structures responsible for signal

  16. Relations among pH, sulfate, and metals concentrations in anthracite and bituminous coal-mine discharges, Pennsylvania

    Science.gov (United States)

    Cravotta, III, Charles A.

    2006-01-01

    Water-quality data for discharges from 140 abandoned mines in the Bituminous and Anthracite Coalfields of Pennsylvania illustrate relations among pH, sulfate, and dissolved metal concentrations. The pH for the 140 samples ranged from 2.7 to 7.3, with two modes at pH 2.5 to 4 (acidic) and 6 to 7 (near neutral). Generally, flow rates were smaller and solute concentrations were greater for low-pH samples; flow rates increased with pH. Although the pH distribution was similar for the bituminous and anthracite subsets, the bituminous discharges had smaller median flow rates, greater concentrations of sulfate, iron, and aluminum, and smaller concentrations of barium and lead than anthracite discharges with the same pH values. The observed relations between the pH and constituent concentrations can be attributed to (1) dilution of acidic water by alkaline ground water; (2) solubility control of aluminum, iron, manganese, barium, and lead by hydroxide, sulfate, and/or carbonate minerals; and (3) aqueous sulfate-complex formation. The formation of AlSO4+ and AlHSO4+2 complexes adds to the total dissolved aluminum concentration at pH of equilibrium with aluminum hydroxide or hydroxysulfate minerals and can account for 10 to 20 times greater concentrations of dissolved aluminum in bituminous discharges compared to anthracite discharges at similar pH. Sulfate complexation also can account for 10 to 30 times greater concentrations of dissolved ferric iron concentrations at equilibrium with ferrihydrite (Fe(OH)3) and/or schwertmannite (Fe8O8(OH)4.5(SO4)1.75) at pH of 3 to 5. In contrast, lower barium and lead concentrations in bituminous than anthracite discharges indicates elevated sulfate concentration could decrease mobility of these metals by the formation of insoluble minerals such as barite (BaSO4) or anglesite (PbSO4). Most samples were saturated with barite, but none were saturated with anglesite. Hence, lead concentrations could be controlled by coprecipitation with

  17. Contribution to physico-chemical study of Timahdit bituminous schists (Morocco): Organic matters and metalloporphyrins

    International Nuclear Information System (INIS)

    Saoiabi, A.

    1982-01-01

    The Timahdit bituminous schists have been analysed by different methods. The experimental results obtained using these methods concern the behaviour of the schists and the Kerogen facing the pyrolysis, as well as the separation of the hydrocarbons and the metalloporphyrins. For this purpose the techniques used are: 'Rock Eval' pyrolysis, thermogravimetric analysis and electron paramagnetic resonance (E.P.R.) for the raw rock and the Kerogen; infrared (I.R.), gas chromatography and E.P.R. for the extracted organic matters; E.P.R., I.R., nuclear magnetic resonance (N.M.R.), ultraviolet (U.V.) and mass spectrometry for the metalloporphyrins identification and characterization. The analysis of these schists has shown that: We can extract per solvent only 1% of organic matters, ferric oxide hasn't any effect neither on the pyrolysis nor on the organic matters extraction and that the Kerogen of these schists are relatively rich in hydrocarbonic compounds. The gas chromatography reveal the presence of alkanes with odd number of carbons and isoprenoids. All these criteria indicate an immature, little developped organic matter which having probably a marine origin but possessing a good oil potential. It has also been observed that a part of Iron, Nickel and Vanadium in the schists are incorporated into the organic matters. Nickel and Vanadium are into macrocycles which are porphyrins. A method for extracting and separating these porphyrins has been developped. 43 figs., 21 tabs., 58 refs. (author)

  18. Highly crystalline Zeolite-A from flyash of bituminous and lignite coal combustion.

    Science.gov (United States)

    Rayalu, S S; Udhoji, J S; Munshi, K N; Hasan, M Z

    2001-11-16

    Flyash is being generated in voluminous amounts by large scale coal combustion process. It poses a serious threat to thermal power industries specifically, in India, wherein the percent of utilisation of flyash is very poor (3-5%). In view of this problem, newer methods of its disposal and utilisation are being explored. The synthesis of zeolite from flyash appears to be one of the most promising alternatives as it has emphasis on value addition to waste material. Flyashes originating from different sources of coal differ in their characteristics and have implications in this work on Zeolite-A production. These factors have been thoroughly investigated and the conditions favourable for formation of Zeolite-A have been delineated. The reactivity of flyash towards zeolite formation is directly dependent on the SiO(2)/Al(2)O(3) ratio, Fe(2)O(3) and CaO content. Amongst the flyashes investigated, so far the sub-bituminous coal based flyash with SiO(2)/Al(2)O(3) ratio of 3.47 appears to be a suitable substrate for Zeolite-A synthesis. These zeolites have been characterised with respect to XRD crystallinity, calcium binding capacity (CBC) and sorption capacity, wherein the crystallinity ranges from 50 to 100%, the CBC ranges from 290 to 560meq/100g and sorption capacity ranges from 16.6 to 23.8%.

  19. Note on the chemical composition of the asphalts of bituminous coal hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Boente, L.

    1942-10-13

    This report was written not as a result of extensive unified experiments, but as a result of collected observations during the course of various investigations. It interpreted two of the major groups of constituents of the asphalts from hydrogenation of bituminous coal as the following: (1) highly condensed aromatics (including heterocyclic compounds with oxygen, nitrogen, or sulfur in the rings) (a) in dehydrogenated form, or (b) in partially hydrogenated form, and (2) reaction products from labile, partially hydrogenated highly condensed aromatics (a) through oxidation reactions, or (b) through condensation and polymerization reactions. These types of compounds seemed to come from rather symmetric precursors that were not split during pressure hydrogenation, as were most constituents of coal, but were dehydrogenated instead. The types of compounds mentioned above shared several properties with the asphalts, including precipitation and adsorption properties. Some examples given of Group 1 compounds were coronene and several derived from it, as well as napthoxanthene, carbazole, and diphenylene sulfide. One example given to illustrate Group 2 was some hypothetical reactions of a proposed hexakeideca-hydrocoronene.

  20. Co-gasification of bituminous coal and hydrochar derived from municipal solid waste: Reactivity and synergy.

    Science.gov (United States)

    Wei, Juntao; Guo, Qinghua; He, Qing; Ding, Lu; Yoshikawa, Kunio; Yu, Guangsuo

    2017-09-01

    In this work, the influences of gasification temperature and blended ratio on co-gasification reactivity and synergy of Shenfu bituminous coal (SF) and municipal solid waste-derived hydrochar (HTC) were investigated using TGA. Additionally, active alkaline and alkaline earth metal (AAEM) transformation during co-gasification was quantitatively analyzed by inductively coupled plasma optical emission spectrometer for correlating synergy on co-gasification reactivity. The results showed that higher char gasification reactivity existed at higher HTC char proportion and gasification temperature, and the main synergy behaviour on co-gasification reactivity was performed as synergistic effect. Enhanced synergistic effect at lower temperature was mainly resulted from more obviously inhibiting the primary AAEM (i.e. active Ca) transformation, and weak synergistic effect still existed at higher temperature since more active K with prominent catalysis was retained. Furthermore, more active HTC-derived AAEM remaining in SF sample during co-gasification would lead to enhanced synergistic effect as HTC char proportion increased. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Recycling of polyethylene terephthalate (PET plastic bottle wastes in bituminous asphaltic concrete

    Directory of Open Access Journals (Sweden)

    Adebayo Olatunbosun Sojobi

    2016-12-01

    Full Text Available This research sheds light on the concept of eco-friendly road construction which comprises eco-design, eco-extraction, eco-manufacturing, eco-construction, eco-rehabilitation, eco-maintenance, eco-demolition, and socioeconomic empowerment. It also revealed the challenges being faced in its adoption and the benefits derivable from its application. Furthermore, the effects of recycling PET plastic bottle wastes produced in North Central Nigeria in bituminous asphaltic concrete (BAC used in flexible pavement construction were also evaluated. The mix design consists of 60/70 penetration-grade asphaltic concrete (5%, 68% coarse aggregate, 6% fine aggregate, and 21% filler using the dry process at 170°C. The optimum bitumen content (OBC for conventional BAC was obtained as 4% by weight of total aggregates and filler. Polymer-coated aggregate (PCA-modified BAC seems preferable because it has the potential to utilize more plastic wastes with a higher optimum plastic content (OPC of 16.7% by weight of total aggregates and filler compared to that of 9% by weight of OBC achieved by PMB-BAC. For both PMB- and PCA-modified BAC, an increase in air void, void in mineral aggregate, and Marshall stability were observed. Eco-friendly road construction which recycles PET wastes should be encouraged by government considering its potential environmental and economic benefits.

  2. Temperature induced development of porous structure of bituminous coal chars at high pressure

    Directory of Open Access Journals (Sweden)

    Natalia Howaniec

    2016-01-01

    Full Text Available The porous structure of chars affects their reactivity in gasification, having an impact on the course and product distribution of the process. The shape, size and connections between pores determine the mechanical properties of chars, as well as heat and mass transport in thermochemical processing. In the study the combined effects of temperature in the range of 973–1273 °K and elevated pressure of 3 MPa on the development of porous structure of bituminous coal chars were investigated. Relatively low heating rate and long residence time characteristic for the in-situ coal conversion were applied. The increase in the temperature to 1173 °K under pressurized conditions resulted in the enhancement of porous structure development reflected in the values of the specific surface area, total pore volume, micropore area and volume, as well as ratio of the micropore volume to the total pore volume. These effects were attributed to the enhanced vaporization and devolatilization, as well as swelling behavior along the increase of temperature and under high pressure, followed by a collapse of pores over certain temperature value. This proves the strong dependence of the porous structure of chars not only on the pyrolysis process conditions but also on the physical and chemical properties of the parent fuel.

  3. Relation Between Bitumen Content and Percentage Air Voids in Semi Dense Bituminous Concrete

    Science.gov (United States)

    Panda, R. P.; Das, Sudhanshu Sekhar; Sahoo, P. K.

    2018-02-01

    Hot mix asphalt (HMA) is a heterogeneous mix of aggregate, mineral filler, bitumen, additives and air voids. Researchers have indicated that the durability of the HMA is sensitive on the actual bitumen content and percentage air void. This paper aims at establishing the relationship between the bitumen content and the percentage air voids in Semi Dense Bituminous Concrete (SDBC) using Viscosity Grade-30 (VG-30) bitumen. Total 54 samples have been collected, for formulation and validation of relationship and observed that the percentage air voids increases with decrease in actual bitumen content and vice versa. A minor increase in percentage air voids beyond practice of designed air voids in Marshall Method of design is required for better performance, indicating a need for reducing the codal provision of minimum bitumen content for SDBC as specified in Specification for Road & Bridges (Fourth Revision) published by Indian Road Congress, 2001. The study shows a possibility of reducing designed minimum bitumen content from codal provision for SDBC by 0.2% of weight with VG-30 grade of Bitumen.

  4. Characteristic Study of Shenmu Bituminous Coal Combustion with Online TG-MS-FTIR

    Science.gov (United States)

    Pan, Guanfu

    2018-01-01

    The combustion characteristics of Shenmu bituminous pulverized coal (SBC) were comprehensively investigated with a combined TG-MS-FTIR system by considering the effect of particle size, heating rate and total flowrate. The combustion products were accurately quantified by normalization and numerical analysis of MS results. The results indicate that the decrease of the particle size, heating rate and total flowrate result in lower ignition and burnout temperatures. The activation energy tends to be lower with smaller particle size, lower heating rate and total flowrate. The MS and FTIR results demonstrate that lower concentrations of different products, such as NO, NO2, HCN, CH4 and SO2 were produced with smaller particle size, slower heating rate and lower total flowrate. The decrease of particle size would lead to more contact area with oxygen and slower heating rate could provide more sufficient time for the diffusion. High total flowrate would reduce the oxygen adsorbability on the coal particle surface and shorten the residence time of oxygen, which makes the ignition difficult to occur. This work will guide to understand the combustion kinetics of pulverized coals and be beneficial to control the formation of pollutants.

  5. Using proximate analysis to characterize airborne dust generation from bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Page, S.J.; Organiscak, J.A.

    2005-11-01

    Prolonged exposure to airborne respirable coal dust is responsible for coal workers pneumoconiosis (CWP), commonly called black lung. Health research studies have identified that the prevalence and severity of CWP are directly related to both the amount of dust exposure and the coal rank. The amount of airborne respirable dust (ARD) smaller than 10 micrometers generated from breakage of different coals varies widely. To investigate the cause, researchers for the National Institute for Occupational Safety and Health (NIOSH) have conducted experiments to identify the causes of airborne respirable dust liberation. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals from eight mines. The results indicate that the proximate analysis of a coal sample can provide a very good indicator of the potential for a dust problem. For application to the coal mining, processing, and utilization industries, data from 977 US coal seams compiled by the Department of Energy (DoE) has been used to calculate this dust generation potential from an equation based on the NIOSH measured data. A simple procedure for this calculation is provided. 1 fig.

  6. Elemental analysis of Indonesian and Australian bituminous coal used at Kapar Power Station

    International Nuclear Information System (INIS)

    Muneer Saleh; Ahmad Suhaimi

    2008-01-01

    An instrumental neutron activation analytical (INAA) technique is used for the determination of thirty elements in five coal samples collected from Kapar power station, imported from Indonesia and Australia. Analyses of the samples are being associated with standards. All irradiation were performed in the nuclear reactor of Malaysia Nuclear Agency (MNA). samples were counted by Hyper Pure Germanium (HPGe) detector for short period irradiations at MNA, while for the long period irradiations the samples were counted at Universiti Kebangsaan Malaysia (UKM). The concentrations of thirty elements have been determined: The major components are Cl, Ca, Mg, K, Fe, Ti, and Na with the mean concentrations in the range between 70±69 ppm-6100±1639 ppm; and the trace elements are Zr, V, Mn, Sc, Cr, Co, As, Br, Rb, Sb, Ba, La, Ce, Nd, Sm, Eu, Tb, Yb, Lu, Hf, Th, U and Ta with the mean concentrations in the range between 0.1381±0.0202 - 69.0±2.8 ppm. The results have been compared to the reported data of eight coal samples from the United States and the reported data of Australian bituminous coal. (Author)

  7. Cigarette smoking and federal black lung benefits in bituminous coal miners.

    Science.gov (United States)

    Roy, T M; Collins, L C; Snider, H L; Anderson, W H

    1989-02-01

    The records of 1000 consecutive coal miners applying for benefits under the Federal Coal Mine Health and Safety Act were examined to determine the contribution of age, dust accumulation, and cigarette smoking to the profile of the miner who satisfies the current pulmonary criteria for disability. Using the presence of pneumoconiosis on chest radiograph as the indication of significant coal dust accumulation, the miners were separated into Group A--those without pneumoconiosis (n = 316) and Group B--those with pneumoconiosis (n = 684). The federal spirometric criteria for disability identified 55/316 miners in Group A (14.5%) and 99/684 miners in Group B (17.4%) potentially eligible for an award (P = .27). The mean ages of miners in both groups did not differ significantly, nor was there difference in the mean ages of groups that did or did not meet the federal criteria. In both groups, those miners potentially eligible for a financial award smoked more cigarettes than did their counterparts (Group A, 31.0 v 18.5 pack-years, P less than .001; Group B, 31.3 v 23.6 pack-years, P less than .001). There was no difference in the smoking histories of the miners from either group who met the federal criteria. Our data indicate that, in the case of bituminous coal miners, the present federal legislation intended to identify and remunerate those who suffer lung impairment from chronic occupational exposure to coal dust is biased in favor of those who sustain additional damage to their ventilatory capacity by smoking cigarettes.

  8. Surface composition of silica particles embedded in an Australian bituminous coal.

    Science.gov (United States)

    Gong, B; Pigram, P J; Lamb, R N

    1999-07-01

    The composition and structure of the surface layers of a series of silica particles (10-20 microns across), embedded in a bituminous coal from the Whybrow seam, Sydney Basin, Australia, have been characterized in situ using time-of-flight secondary ion mass spectrometry (TOFSIMS), ion imaging, and depth profiling. The silica particles investigated are typically encased in a multilayered shell, the composition of which differs from average composition of both the silica and the bulk coal. The analysis directly demonstrates the presence of a silanol-rich (Si-OH) interfacial layer 3 nm in thickness. This silanol-rich region separates the bulk silica and a complex non-silica layer encasing the particles. The interfacial region also shows significant lithium enrichment (approximately fivefold over bulk) which implies diffusion and precipitation of lithium-containing species during the authigenetic formation of the surface layers of the silica grains. The outer layer encasing the silica particles is 10 nm in thickness and is composed of clays and carbonates, and, in some cases, includes organic material. The elemental constituents of this layer include aluminium, sodium, potassium, magnesium, iron, and lesser amounts of titanium and copper. The variation in the aluminium concentration from the outermost surface to the deeper layers is less than that of other non-silica species. A relatively high amount of calcium is found associated with the silica bulk. Although only non-respirable-sized silica particles are examined in this work, the methods of analysis developed have potential in providing an insight into the surface composition of respirable particles and in further studies of the surface bioavailability of silica species.

  9. Characterize Cold Bituminous Emulsion Mixtures Incorporated Ordinary Portland Cement Filler for Local Surface Layer

    Directory of Open Access Journals (Sweden)

    Mustafa Amoori Kadhim

    2018-02-01

    Full Text Available Cold Bituminous Emulsion Mixtures have many environmental, logistical, and economic advantages over conventional Hot Mix Asphalt. Nevertheless, their inferior performance and high water sensitivity at early life attract little attentions. Moreover, it is impossible to apply CBEM as a structural surface layer if left without treatment or enhancement. The main aim of this study is to enhance the properties of CBEM for the hope of using it as a structural layer. Thus, a trial has been made to improve CBEM mechanical and durability properties by replacing the Ordinary Portland Cement by the Conventional Mineral Filler with 3 percentages; namely, 0, 50%, and 100%. CBEM mixtures mechanical properties were evaluated in term of Marshall Stability and Flow, Indirect Tensile Strength, and Wheel Track Test. While Moisture damage was evaluated in terms of Retained Marshall Stability. Test results showed that the addition of 100%OPC filler can improve CBEM mechanical and durability properties efficiently. In terms of mechanical properties results, CBEM comprised 100%OPC, can be used as a structural Surface layer based on local Iraqi specifications limits, where mixture enhanced about 1.9, 1.78, 9,4.85, and 2.6  times in term of MS, MF, rutting deformation resistance, resistance to tensile cracking, and moisture damage resistance, respectively as compared to untreated CBEM. Also, CBEM-100%OPC mix seemed comparable (and sometime superior to HMA, e.g., resistance to rutting of CBEM is about 6.2 times higher than that of HMA. It’s worth to say that OPC upgrades CBEM to a significant level that enables it to use as a structural layer in terms of the mechanical and the durability properties.

  10. Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Carl Richardson; Katherine Dombrowski; Douglas Orr

    2006-12-31

    This project Final Report is submitted to the U.S. Department of Energy (DOE) as part of Cooperative Agreement DE-FC26-03NT41987, 'Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas.' Sorbent injection technology is targeted as the primary mercury control process on plants burning low/medium sulfur bituminous coals equipped with ESP and ESP/FGD systems. About 70% of the ESPs used in the utility industry have SCAs less than 300 ft2/1000 acfm. Prior to this test program, previous sorbent injection tests had focused on large-SCA ESPs. This DOE-NETL program was designed to generate data to evaluate the performance and economic feasibility of sorbent injection for mercury control at power plants that fire bituminous coal and are configured with small-sized electrostatic precipitators and/or an ESP-flue gas desulfurization (FGD) configuration. EPRI and Southern Company were co-funders for the test program. Southern Company and Reliant Energy provided host sites for testing and technical input to the project. URS Group was the prime contractor to NETL. ADA-ES and Apogee Scientific Inc. were sub-contractors to URS and was responsible for all aspects of the sorbent injection systems design, installation and operation at the different host sites. Full-scale sorbent injection for mercury control was evaluated at three sites: Georgia Power's Plant Yates Units 1 and 2 [Georgia Power is a subsidiary of the Southern Company] and Reliant Energy's Shawville Unit 3. Georgia Power's Plant Yates Unit 1 has an existing small-SCA cold-side ESP followed by a Chiyoda CT-121 wet scrubber. Yates Unit 2 is also equipped with a small-SCA ESP and a dual flue gas conditioning system. Unit 2 has no SO2 control system. Shawville Unit 3 is equipped with two small-SCA cold-side ESPs operated in series. All ESP systems tested in this program had SCAs less than 250 ft2/1000 acfm. Short-term parametric tests were conducted on Yates

  11. Analysis of the sensitivity of the impact resonance frequency test as a tool to determine the elastic properties of bituminous materials

    Directory of Open Access Journals (Sweden)

    R. Tauste

    2017-07-01

    Full Text Available The modulus value of bituminous materials is a key factor in the design of road pavements and the estimation of their life service. This parameter can be measured in laboratory but, unfortunately, this requires the deterioration of the pavement so as the consumption of time and resources. Therefore, this study analyses the feasibility of using impact resonance frequency tests as an alternative to traditional methods for determining the dynamic modulus of bituminous mixtures. The sensitivity of this technique has been studied by analyzing its repeatability and reproducibility, studying the variations in the values measured by modifying the dimensions of the specimens, test temperatures and types of mixture tested. In addition, this non-destructive technique has been compared with other traditional tests used to determine the elastic properties of bituminous materials. The results show that this test could be an interesting tool to characterize the properties and damage state of asphalt layers.

  12. Analysis of the sensitivity of the impact resonance frequency test as a tool to determine the elastic properties of bituminous materials

    International Nuclear Information System (INIS)

    Tauste, R.; Moreno-Navarro, F.; Gallego, R.; Rubio-Gámez, M.C.

    2017-01-01

    The modulus value of bituminous materials is a key factor in the design of road pavements and the estimation of their life service. This parameter can be measured in laboratory but, unfortunately, this requires the deterioration of the pavement so as the consumption of time and resources. Therefore, this study analyses the feasibility of using impact resonance frequency tests as an alternative to traditional methods for determining the dynamic modulus of bituminous mixtures. The sensitivity of this technique has been studied by analyzing its repeatability and reproducibility, studying the variations in the values measured by modifying the dimensions of the specimens, test temperatures and types of mixture tested. In addition, this non-destructive technique has been compared with other traditional tests used to determine the elastic properties of bituminous materials. The results show that this test could be an interesting tool to characterize the properties and damage state of asphalt layers. [es

  13. Multinomial logit analysis of injury severity in U.S. underground bituminous coal mines, 1975-1982.

    Science.gov (United States)

    Bennett, J D; Passmore, D L

    1985-10-01

    Relationships among mine and injured miner characteristics and degrees of injury are examined for 91 404 injuries in underground bituminous coal mines in the United States from 1975 through 1982. Injury severity varies by the mining system, geographical region, circumstances surrounding the injury, the injured miner's age, whether the miner was using powered equipment, the year in which the injury occurred and the location in the mine where the injury happened. Injury severity is not related to the injured miner's total mining experience, job experience and experience in the mine in which the injury occurred.

  14. Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

    Science.gov (United States)

    Cieślik, Ewelina; Konieczny, Tomasz; Bobik, Bartłomiej

    2018-01-01

    One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction) were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

  15. Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

    Directory of Open Access Journals (Sweden)

    Cieślik Ewelina

    2018-01-01

    Full Text Available One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

  16. Report: Potential environmental impact of exempt site materials - a case study of bituminous road planings and waste soils.

    Science.gov (United States)

    Bark, Marjorie; Bland, Michael; Grimes, Sue

    2009-09-01

    The use of waste materials for ecological benefit, agricultural improvement or as part of construction works are often exempt from waste management control in order to maximize the reuse of material that would otherwise be disposed of to landfill. It is important, however, to determine whether there is potential for such waste to cause environmental harm in the context of the basis for granting exemptions under the relevant framework objective to ensure that waste is recovered or disposed of without risk to water, air, soil, plants or animals. The potential for environmental harm was investigated by leaching studies on two wastes commonly found at exempt sites: bituminous road planings and waste soils. For bituminous road planings, the organic components of the waste were identified by their solubility in organic solvents but these components would have low environmental impact in terms of bioavailability. Leaching studies of the heavy metals copper, lead and zinc, into the environment, under specific conditions and particularly those modelling acid rain and landfill leachate conditions showed that, except for copper, the amounts leached fell within Waste Acceptance Criteria compliance limits for defining waste as inert waste. The fact that the amount of copper leached was greater than the Waste Acceptance Criteria level suggests that either additional testing of wastes regarded as exempt should be carried out to ensure that they are in analytical compliance or that legislation should allow for the potential benefits of reuse to supersede deviations from analytical compliance.

  17. A note on the market potential of low-volatile bituminous coal, Willow Creek property, northeastern British Columbia

    Energy Technology Data Exchange (ETDEWEB)

    Barry Ryan; Ted Todoschuk; Bob Lane [British Columbia Ministry of Energy and Mines, BC (Canada)

    2004-07-01

    The international coking coal market is very competitive and is segmented into many non inter changeable coal products. Two products, that are more in demand than many are, low-volatile bituminous high rank coking coal for blends into coke ovens, and low-volatile bituminous coal for pulverization and injection into blast furnaces (PCI coal). The Willow Creek property contains coal that may be suitable for these two markets. The higher priced market is the low-volatile coking coal market where up to 30% of this coal can be added into coal blends for coke ovens. This is a higher priced market than the PCI market and it is advantageous for mines if possible to switch from the low-volatile PCI market to the low-volatile coking coal market. Low-volatile coking coal is also in short supply as reserves in the US and other countries are running out. This note looks at the possible use of 7 Seam from the Willow Creek property in northeastern British Columbia as a low-volatile component in a standard coke oven blend. The Willow Creek property is located 40 kilometres west of Chetwynd and overlies seams in the Gething Formation. 15 refs., 4 figs., 11 tabs.

  18. Sedimentation technique of waste bituminization and thermogravimetric characteristics of the finalproducts

    International Nuclear Information System (INIS)

    Zeger, J.; Knotik, K.

    1976-01-01

    In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GesmbH a semitechnical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant is using a new technological process for embedding. One of the important features of this new process is that the, normally inactive solution water is distilled off prior to the embedding, resulting in dry and powdery salts. The second important feature is that the mixing of these dry salts with the thin fluid bitumen is done by sedimentation. Expecially there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant, were carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. Analysis was performed by heating the samples, consisting of various mixtures of bitumen and inorganic salts, in a METTLER-Thermoanalyzer up to 500 0 C using different atmospheres (air, nitrogen). It could be shown that only nitrate and nitrite especially in combination with Fe(III)-ions are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410 0 C (above the melting point of both NaNO 2 and NaNO 3 ). The Fe-ions hava a catalytic influence, as it could be shown that 1 1% addiation of Fe(NO 3 ) 3 to NaNO 3 leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extend by a hydrolysis prior to the embedding. In preparation of further studies concerning the behaviour of radiation damaged bitumen there has been developed a method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture. This is done by making two measurements with glass dosimeters. One with a beta-absorber to get a pure gamma-dose and the other without it to get the combined beta and gamma dose. (author)

  19. Non-catalytic co-gasification of sub-bituminous coal and biomass

    Science.gov (United States)

    Nyendu, Guevara Che

    Fluidization characteristics and co-gasification of pulverized sub-bituminous coal, hybrid poplar wood, corn stover, switchgrass, and their mixtures were investigated. Co-gasification studies were performed over temperature range from 700°C to 900°C in different media (N2, CO2, steam) using a bubbling fluidized bed reactor. In fluidization experiments, pressure drop (Delta P) observed for coal-biomass mixtures was higher than those of single coal and biomass bed materials in the complete fluidization regime. There was no systematic trend observed for minimum fluidization velocity ( Umf) with increasing biomass content. However, porosity at minimum fluidization (εmf) increased with increasing biomass content. Channeling effects were observed in biomass bed materials and coal bed with 40 wt.% and 50 wt.% biomass content at low gas flowrates. The effect of coal pressure overshoot reduced with increasing biomass content. Co-gasification of coal and corn stover mixtures showed minor interactions. Synergetic effects were observed with 10 wt.% corn stover. Coal mixed with corn stover formed agglomerates during co-gasification experiments and the effect was severe with increase in corn stover content and at 900°C. Syngas (H2 + CO) concentrations obtained using CO2 as co-gasification medium were higher (~78 vol.% at 700°C, ~87 vol.% at 800°C, ~93 vol.% at 900°C) than those obtained with N2 medium (~60 vol.% at 700°C, ~65 vol.% at 800°C, ~75 vol.% at 900°C). Experiments involving co-gasification of coal with poplar showed no synergetic effects. Experimental yields were identical to predicted yields. However, synergetic effects were observed on H2 production when steam was used as the co-gasification medium. Additionally, the presence of steam increased H2/CO ratio up to 2.5 with 10 wt.% hybrid poplar content. Overall, char and tar yields decreased with increasing temperature and increasing biomass content, which led to increase in product gas.

  20. Dependence of carbon dioxide sorption on the petrographic composition of bituminous coals from the Czech part of the Upper Silesian Basin, Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Weishauptová, Zuzana; Sýkorová, Ivana

    2011-01-01

    Roč. 90, č. 1 (2011), s. 312-323 ISSN 0016-2361 R&D Projects: GA ČR GA106/08/1146; GA AV ČR IAA300460804 Institutional research plan: CEZ:AV0Z30460519 Keywords : bituminous coal * sorption capacity * maceral composition Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.248, year: 2011

  1. Organic petrology and geochemistry of Eocene Suzak bituminous marl, north-central Afghanistan: Depositional environment and source rock potential

    Science.gov (United States)

    Hackley, Paul C.; Sanfilipo, John

    2016-01-01

    Organic geochemistry and petrology of Eocene Suzak bituminous marl outcrop samples from Madr village in north-central Afghanistan were characterized via an integrated analytical approach to evaluate depositional environment and source rock potential. Multiple proxies suggest the organic-rich (TOC ∼6 wt.%) bituminous marls are ‘immature’ for oil generation (e.g., vitrinite Ro extracts with high polar components, consistent with extraction from S-rich Type IIs organic matter which could generate hydrocarbons at low thermal maturity. Low Fe-sulfide mineral abundance and comparison of Pr/Ph ratios between saturate and whole extracts suggest limited Fe concentration resulted in sulfurization of organic matter during early diagenesis. From these observations, we infer that a Type IIs kerogen in ‘immature’ bituminous marl at Madr could be generating high sulfur viscous oil which is seeping from outcrop. However, oil-seep samples were not collected for correlation studies. Aluminum-normalized trace element concentrations indicate enrichment of redox sensitive trace elements Mo, U and V and suggest anoxic-euxinic conditions during sediment deposition. The bulk of organic matter observed via optical microscopy is strongly fluorescent amorphous bituminite grading to lamalginite, possibly representing microbial mat facies. Short chain n-alkanes peak at C14–C16 (n-C17/n-C29 > 1) indicating organic input from marine algae and/or bacterial biomass, and sterane/hopane ratios are low (0.12–0.14). Monoaromatic steroids are dominated by C28clearly indicating a marine setting. High gammacerane index values (∼0.9) are consistent with anoxia stratification and may indicate intermittent saline-hypersaline conditions. Stable C isotope ratios also suggest a marine depositional scenario for the Suzak samples, consistent with the presence of marine foraminifera including abundant planktic globigerinida(?) and rare benthic discocyclina(?) and nummulites(?). Biomarker 2

  2. Analysis of the use of coal tar as a binder in bituminous mixtures, using Marshall and Ramcodes methodologies

    Science.gov (United States)

    Ochoa-Díaz, R.

    2013-11-01

    This paper presents an alternative use of coal tar, a by-product of the steel industry, given the problems of accumulation and negative environmental impact. Therefore, it is necessary to analyze the incorporation of coal tar as a binder in paving mixtures. First, this paper presents the origin, description of the main characteristics, and properties of tar. Then, this paper evaluates the mix of coal tar by means of the RAMCODES and Marshall methodologies to determine its resistance. The results of the tests explain the physical and mechanical properties of the mix. Taking into account the results of both methods, this paper makes a comparison to determine the suitability of the RAMCODES methodology in the mix design. Finally, it analyzes the alternatives to coal tar that can be used as binders in bituminous mixes for pavement and the advantages of their uses under some specific conditions.

  3. Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

    Science.gov (United States)

    Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

    2012-11-01

    The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. Bituminous solidification, disposal, transport and burial of spent ion-exchange resins. Part of a coordinated programme on treatment of spent ion exchange resins

    International Nuclear Information System (INIS)

    Mozes, G.; Kristof, M.

    1983-07-01

    The project dealing with the incorporation of spent ion-exchange resins into bitumen was performed within the Agency coordinated research programme on treatment of spent ion-exchange resins. Physical and chemical properties of commercial ion-exchange resins, bitumens and bituminized resins were studied. It was shown that bitumen with low oil content and with a softening point of 60-70 deg. C are applicable for the incorporation of resins. The final waste form is allowed to contain maximum 50% resin. The comprehensive study of the biological resistance of B-30 bitumen was performed. That showed that any bacteriological attack can be regarded as generally insignificant. A continuously operating technology was realized on a semi-plant scale. The best operating conditions of this technology were determined. On the basis of the experience gained from the experiments a design of the bituminization plant of 50m 3 dry resin/year treatment capacity was proposed

  5. Advances in Interlaboratory Testing and Evaluation of Bituminous Materials State-of-the-Art Report of the RILEM Technical Committee 206-ATB

    CERN Document Server

    Bahia, Hussain; Canestrari, Francesco; Roche, Chantal; Benedetto, Hervé; Piber, Herald; Sybilski, Dariusz

    2013-01-01

    This STAR on asphalt materials presents the achievements of RILEM TC 206 ATB, acquired over many years of interlaboratory tests and international knowledge exchange. It covers experimental aspects of bituminous binder fatigue testing; the background on compaction methods and imaging techniques for characterizing asphalt mixtures including validation of a new imaging software; it focuses on experimental questions and analysis tools regarding mechanical wheel tracking tests, comparing results from different labs and using finite element techniques. Furthermore, long-term rutting prediction and evaluation for an Austrian road are discussed, followed by an extensive analysis and test program on interlayer bond testing of three different test sections which were specifically constructed for this purpose. Finally, the key issue of manufacturing reclaimed hot mix asphalt in the laboratory is studied and recommendations for laboratory ageing of bituminous mixtures are given.

  6. Effect of transesterification degree and post-treatment on the in-service performance of NCO-functionalized vegetable oil bituminous products

    OpenAIRE

    Cuadri Vega, Antonio Abad; García Morales, Moisés; Navarro Domínguez, Francisco Javier; Partal López, Pedro

    2014-01-01

    The bitumen modification through polyurethane prepolymers presents significant benefits for the manufacture of bituminous products for the paving industry. In this sense, this work explores the use, as bitumen modifier, of a novel reactive prepolymer synthesized by reaction of 4,4´,diphenylmethane diisocyanate (MDI) and a vegetable oil-based polyol, castor oil (CO), previously transesterified with pentaerythritol. On the one hand, thermal analysis on transesterified CO revealed a highly stabl...

  7. Evaluation of bituminous sub-ballast manufactured at low temperatures as an alternative for the construction of more sustainable railway structures

    Directory of Open Access Journals (Sweden)

    L. Pirozzolo

    2017-07-01

    Full Text Available Hot bituminous mixtures are becoming widely used in modern railway tracks in the sub-ballast layer. The reason is that these materials allow for both an increase in bearing capacity and greater protection of the substructure respect the traditional granular sub-ballast. Despite these advantages, the fact that these materials are manufactured at a temperature of 160°C means that their application can lead to an important increase in construction costs, pollution and energy consumption. This paper aims to study the possibility of using WMA manufactured at lower temperatures, as bituminous sub-ballast, in order to save energy and reduce emissions throughout the production process, as well as diminish the global costs of this layer. To this end, this study focuses on a comparison of the mechanical behaviour of warm and hot bituminous mixtures as sub-ballast under various loading conditions. The results indicate that WMA offers mechanical behaviour that is comparable to conventional HMA.

  8. Sphagnum mosses from 21 ombrotrophic bogs in the athabasca bituminous sands region show no significant atmospheric contamination of "heavy metals".

    Science.gov (United States)

    Shotyk, William; Belland, Rene; Duke, John; Kempter, Heike; Krachler, Michael; Noernberg, Tommy; Pelletier, Rick; Vile, Melanie A; Wieder, Kelman; Zaccone, Claudio; Zhang, Shuangquan

    2014-11-04

    Sphagnum moss was collected from 21 ombrotrophic (rain-fed) peat bogs surrounding open pit mines and upgrading facilities of Athabasca bituminous sands in Alberta (AB). In comparison to contemporary Sphagnum moss from four bogs in rural locations of southern Germany (DE), the AB mosses yielded lower concentrations of Ag, Cd, Ni, Pb, Sb, and Tl, similar concentrations of Mo, but greater concentrations of Ba, Th, and V. Except for V, in comparison to the "cleanest", ancient peat samples ever tested from the northern hemisphere (ca. 6000-9000 years old), the concentrations of each of these metals in the AB mosses are within a factor of 3 of "natural, background" values. The concentrations of "heavy metals" in the mosses, however, are proportional to the concentration of Th (a conservative, lithophile element) and, therefore, contributed to the plants primarily in the form of mineral dust particles. Vanadium, the single most abundant trace metal in bitumen, is the only anomaly: in the AB mosses, V exceeds that of ancient peat by a factor of 6; it is therefore enriched in the mosses, relative to Th, by a factor of 2. In comparison to the surface layer of peat cores collected in recent years from across Canada, from British Columbia to New Brunswick, the Pb concentrations in the mosses from AB are far lower.

  9. Utilising neural networks and closed form solutions to determine static creep behaviour and optimal polypropylene amount in bituminous mixtures

    Directory of Open Access Journals (Sweden)

    Serkan Tapkın

    2012-12-01

    Full Text Available The testing procedure in order to determine the precise mechanical testing results in Marshall design is very time consuming. Also, the physical properties of the asphalt samples are obtained by further calculations. Therefore if the researchers can obtain the stability and flow values of a standard mixture with the help of mechanical testing, the rest of the calculations will just be mathematical manipulations. Determination of mechanical testing parameters such as strain accumulation, creep stiffness, stability, flow and Marshall Quotient of dense bituminous mixtures by utilising artificial neural networks is important in the sense that, cumbersome testing procedures can be avoided with the help of the closed form solutions provided in this study. Marshall specimens, prepared by utilising polypropylene fibers, were tested by universal testing machine carrying out static creep tests to investigate the rutting potential of these mixtures. On the very well trained data basis, artificial neural network analyses were carried out to propose five separate models for mechanical testing properties. The explicit formulation of these five main mechanical testing properties by closed form solutions are presented for further use for researches.

  10. Study on co-pyrolysis characteristics of rice straw and Shenfu bituminous coal blends in a fixed bed reactor.

    Science.gov (United States)

    Li, Shuaidan; Chen, Xueli; Liu, Aibin; Wang, Li; Yu, Guangsuo

    2014-03-01

    Co-pyrolysis behaviors of rice straw and Shenfu bituminous coal were studied in a fixed bed reactor under nitrogen atmosphere. The pyrolysis temperatures were 700°C, 800°C and 900°C, respectively. Six different biomass ratios were used. Gas, tar components were analyzed by a gas chromatograph and a gas chromatography-mass spectrometry respectively. Under co-pyrolysis conditions, the gas volume yields are higher than the calculated values. Co-pyrolysis tar contains more phenolics, less oxygenate compounds than calculated values. The addition of biomass changes the atmosphere during the pyrolysis process and promotes tar decomposition. The SEM results show that the differences between the blended char and their parents char are not significant. The results of char yields and ultimate analysis also show that no significant interactions exist between the two kinds of particles. The changes of gas yield and components are caused by the secondary reactions and tar decomposition. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Applied Technological Direction of Power Plant Ash and Slag Waste Management when Kuznetsk Bituminous Coal is Burned

    Directory of Open Access Journals (Sweden)

    Lihach Snejana A.

    2016-01-01

    Full Text Available Currently a lot of power plants have a problem with storage of coal combustion solid by-products (ash and slag. Holding capacity of existing power plants available ash dumps were enlarged and modernized repeatedly. Many plants have two or even three of them. Today new ash dump construction is economically inconvenient due to need to assign new plots of land and their inconveniently big distance from a plant, which increase ash and slag transportation expenses. The goal of our research work is to find promising directions for ash and slag waste mass utilization based on Kuznetsk bituminous coals experimental data on ultimate composition and properties. The experimental research of ash, slag and their mixture samples from ash dumps brought us to conclusion that the most promising direction for these materials application in large quantities is construction industry including road construction. Be-sides, we lined up some other directions for ash, slag, and ash and slag mixture possible application. These directions might not provide mass utilization but they are promising from a point of view of the researched waste properties.

  12. Co-combustion of bituminous coal and biomass fuel blends: Thermochemical characterization, potential utilization and environmental advantage.

    Science.gov (United States)

    Zhou, Chuncai; Liu, Guijian; Wang, Xudong; Qi, Cuicui

    2016-10-01

    The thermochemical characteristics and gaseous trace pollutant behaviors during co-combustion medium-to-low ash bituminous coal with typical biomass residues (corn stalk and sawdust) were investigated. Lowering of ignition index, burnout temperature and activation energy in the major combustion stage are observed in the coal/biomass blends. The blending proportion of 20% and 30% are regarded as the optimum blends for corn stalk and sawdust, respectively, in according the limitations of heating value, activation energy, flame stability and base/acid ratio. The reductions of gaseous As, Cd, Cu, Pb, Zn and polycyclic aromatic hydrocarbon (PAHs) were 4.5%, 7.8%, 6.3%, 9.8%, 9.4% and 17.4%, respectively, when co-combustion coal with 20% corn stalk. The elevated capture of trace elements were found in coal/corn stalk blend, while the coal/sawdust blend has the better PAHs control potential. The reduction mechanisms of gaseous trace pollutants were attributed to the fuel property, ash composition and relative residence time during combustion. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Assessment of underground coal gasification in bituminous coals: potential UCG products and markets. Final report, Phase I

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-01-31

    The following conclusions were drawn from the study: (1) The US will continue to require new sources of energy fuels and substitutes for petrochemical feedstocks into the foreseeable future. Most of this requirement will be met using coal. However, the cost of mining, transporting, cleaning, and preparing coal, disposing of ash or slag and scrubbing stack gases continues to rise; particularly, in the Eastern US where the need is greatest. UCG avoids these pitfalls and, as such, should be considered a viable alternative to the mining of deeper coals. (2) Of the two possible product gases LBG and MBG, MBG is the most versatile. (3) The most logical use for UCG product in the Eastern US is to generate power on-site using a combined-cycle or co-generation system. Either low or medium Btu gas (LBG or MBG) can be used. (4) UCG should be an option whenever surface gasification is considered; particularly, in areas where deeper, higher sulfur coal is located. (5) There are environmental and social benefits to use of UCG over surface gasification in the Eastern US. (6) A site could be chosen almost anywhere in the Illinois and Ohio area where amenable UCG coal has been determined due to the existence of existing transportation or transmission systems. (7) The technology needs to be demonstrated and the potential economic viability determined at a site in the East-North-Central US which has commercial quantities of amenable bituminous coal before utilities will show significant interest.

  14. Dye-adsorption capacity of bituminous fly ash and its pozzolanic property after used as dye-adsorbent

    Directory of Open Access Journals (Sweden)

    Penpolcharoen, M.

    2004-02-01

    Full Text Available Bituminous fly ash, which is an industrial waste, was used as an adsorbent to remove dyestuff from the textile-dye wastewater. The batch kinetic and isotherm experiments of the synthetic wastewater were firstly conducted to determine the adsorption behavior and optimal conditions for adsorption. The optimal conditions were then applied to the actual textile-dye wastewater. Under the original conditions of fly ash and wastewater, the results indicated that the color could be removed up to 86.65% by 12 g of the fly ash /L of the wastewater within 30 min. Its adsorption was described by the Freundlich isotherm. The dye-adsorbed fly ash was further studied on its pozzolanic property in terms of compressive strength by using it as a partial substitute to Portland cement type I to produce mortar. The result revealed that the highest compressive strength was of the sample containing 10% by weight of the dye-adsorbed fly ash in replacement of cement. It possessed 215 kg/cm2 at 28 days, which is 92.67% of the sample containing 10% by weight of the original fly ash in replacement of cement, or 83.33 of the cement mortar. For the environmental concern, leachabilities of lead (Pb, chromium (Cr, copper (Cu and zinc (Zn from all mortars were also carried out. No leaching of the heavy metals from any samples could be detected. Hence, the dye-adsorbed fly ash can be used as an environmental friendly construction material.

  15. Effect of asphaltene and resin oils on the viscosity of bituminous petroleum materials to be used as asphalt primers

    Directory of Open Access Journals (Sweden)

    Bencomo, M. R.

    2006-03-01

    Full Text Available The bituminous crude from the Machete, Venezuela, area, which has such a fluid consistency that it falls outside the normal scope of the A5TM D-5 (1 penetration test exceeding the 3D-mm ceiling specified in that standard and can be used as an asphalt primer: Like other asphalt products, these materials are -chemically speaking- a mix of numerous naphthenic, paraffinic and aromatic hydrocarbons and heterocyclic compounds containing sulphur, nitrogen, oxygen and so on. They have a dense and a malthene oil phase which, along with the natural hydrocarbons additives used in these products acts as a volatile fluidizer. The former is described as a mix of asphaltenes: complex high molecular weight substances that are insoluble in paraffinic hydrocarbons and soluble in aromatic compounds such as benzene. The malthene oil phase, in turn, consists in a mix of resins and hydrocarbons and together the two constitute a colloidal system. The experiments discussed in the present paper were conducted to determine the effect of the proportion of asphaltenes and resin oils on the viscosity of such bituminous crude emulsions/ with a view to their use as primers. These experiments were run in a Parr batch reactor in a nitrogen atmosphere using n-heptane as a solvent. The resins were separated after the asphaltenes precipitated from the samples and subsequently from the malthene fraction obtained. The results showed that the asphaltenes account for the structural characteristics and consistency of the medium and the resin oils for its cohesive properties/,the malthene oils act as solvents.Los crudos extrapesados procedentes del área Machete (Venezuela son materiales de consistencia blanda o fluida, por lo que se salen del campo en el que normalmente se aplica el ensayo de penetración a productos asfálticos según el método ASTM D-5 (1, cuyo límite máximo es 30 mm, y pueden ser utilizados como pinturas asfálticas de imprimación. Al igual que otros productos

  16. Effects of Steam and CO2 in the Fluidizing Gas when Using Bituminous Coal in Chemical-Looping Combustion

    Science.gov (United States)

    Leion, H.; Lyngfelt, A.; Mattisson, T.

    Chemical-looping combustion (CLC) is a combustion technology where an oxygen carrier is used to transfer oxygen from the combustion air to the fuel in order to avoid direct contact between air and fuel. Thus, the CO2 is inherently separated from the flue gases with a potential for considerably lower energy penalty and cost compared to other techniques for CO2 separation. The oxygen carrier is circulated between two reactors, a fuel and an air reactor, where the flue gas from the air reactor contains oxygen depleted air and the flue gas from the fuel reactor contains mainly CO2 and H2O. The water can easily be condensed and the remaining CO2 can be transported for underground storage. Most of the prior work with CLC has focused on using natural gas and syngas as fuel and oxygen carrying material normally produced from pure chemicals. However, recent work on adapting the CLC process for solid fuels with ores and natural minerals as oxygen carrier shows promising results. This paper will present results from reactivity investigations in a laboratory fluidized-bed reactor system using previously investigated natural mineral ilmenite as oxygen carrier and a bituminous Colombian coal as fuel. Experiments were conducted at a temperature of 970°C with N2, steam, and/or CO2 in the fluidizing gas. Synergy effects between steam and CO2 on fuel conversion was noted. The results show that the fuel conversion was a roughly a factor 5 faster with steam as compared to CO2 in the fluidizing gas.

  17. Adapting palynological preparation methods in subbituminous and bituminous coals from Colombia to improve palynofacies and hydrocarbon source rock evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Blandon, Astrid; Arango, Fredy [Facultad de Minas, Universidad Nacional de Colombia, Calle 65, 78-28, Medellin (Colombia); Parra, Norberto [Facultad de Ciencias, Universidad Nacional de Colombia, Calle 59A, 63-020, Medellin (Colombia); Gorin, Georges E. [Dpmt. Geology-Paleontology, University of Geneva, 13 rue des Maraichers, 1205 Geneva (Switzerland)

    2008-01-21

    Apart from their potential as fossil fuel, bituminous and subbituminous coals in Colombia may prove to be potential source rocks for the generation of hydrocarbons. The assessment of such properties requires the combination of petrographic and palynofacies studies. The latter correspond to the microscopic investigation in transmitted white and reflected UV lights of sedimentary organic matter insoluble in organic and inorganic solvents. To date, mineral acid and Schulze methods have failed to produce good samples of palynofacies constituents from Cenozoic coals in Colombia, so that the latter method had to be modified. The main modifications consist in adapting the KClO{sub 3} to HNO{sub 3} ratio in the Schulze mixture and introducing two extra phases of oxidation with NaOH and NH{sub 4}OH, which permit the washing off of humic substances. This method yields the full spectrum of palynofacies constituents, which are not destroyed or damaged by the alkali treatment. Neither is their fluorescence colour affected by the initial acid treatment. On the contrary, the particle fluorescence intensity tends to increase because of the dissolution of humic acids, making their identification easier. The achievements of the modified method are threefold: 1) it permits the correlation between macerals in petrographic polished sections and their equivalent in palynofacies slides, making the two methods complementary; 2) palynofacies provides a better identification of sporomorphs than petrography, resulting in better paleoenvironmental interpretations; 3) palynofacies tend to give a more precise quantitative evaluation of the liptinitic constituents, and consequently, of the coal hydrocarbon generation potential. (author)

  18. The influence of seam height on lost-time injury and fatality rates at small underground bituminous coal mines.

    Science.gov (United States)

    Peters, R H; Fotta, B; Mallett, L G

    2001-11-01

    Due to variations in the thickness of U.S. coal seams, there is great variability in the height of the roof where underground miners work. Restrictions imposed by low seam heights have important safety consequences. As the height of their workplace decreases, miners must stoop, duck walk, or crawl, and their vision, posture, and mobility become increasingly restricted. Low seam height also places important restrictions on the design of mobile equipment and other mining machinery. Using the employment and injury data reported to the Mine Safety and Health Administration (MSHA) from 1990 to 1996, small underground bituminous coal mines with less than 50 employees were stratified by average coal seam height according to the following categories: low ( or =61"). Injury rates for both nonfatal days lost and fatality cases were examined by seam height and leading type of injury incidents. The leading types of incidents associated with fatalities were roof falls and powered haulage equipment. In comparison to high-seam mines, miners working in low or medium seams are at higher risk of being killed by powered haulage equipment, roof bolting machines, and falls of unsupported roof. The leading types of incidents associated with nonfatal injuries were handling materials and powered haulage. As mining height decreases, miners are at increasingly higher risk of having a nonfatal injury from incidents involving roof bolting machines, load-haul-dump equipment, personnel carriers, and powered haulage conveyors. As mining height increases, miners are at increasingly higher risk of having a nonfatal injury from slips and falls and incidents involving shuttle cars and roof and rib falls. Knee injuries are a particularly severe problem in low-seam mines. The rate of injuries to miners while crawling or kneeling is 10 times higher in low seams than in high seams.

  19. Catalytic Two-Stage Liquefaction (CTSL{trademark}) process bench studies and PDU scale-up with sub-bituminous coal. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Comolli, A.G.; Johanson, E.S.; Karolkiewicz, W.F.; Lee, L.K.T.; Stalzer, R.H.; Smith, T.O.

    1993-03-01

    Reported are the details and results of Laboratory and Bench-Scale experiments using sub-bituminous coal conducted at Hydrocarbon Research, Inc., under DOE Contract No. DE-AC22-88PC88818 during the period October 1, 1988 to December 31, 1992. The work described is primarily concerned with testing of the baseline Catalytic Two-Stage Liquefaction (CTSL{trademark}) process with comparisons with other two stage process configurations, catalyst evaluations and unit operations such as solid separation, pretreatments, on-line hydrotreating, and an examination of new concepts. In the overall program, three coals were evaluated, bituminous Illinois No. 6, Burning Star and sub-bituminous Wyoming Black Thunder and New Mexico McKinley Mine seams. The results from a total of 16 bench-scale runs are reported and analyzed in detail. The runs (experiments) concern process variables, variable reactor volumes, catalysts (both supported, dispersed and rejuvenated), coal cleaned by agglomeration, hot slurry treatments, reactor sequence, on-line hydrotreating, dispersed catalyst with pretreatment reactors and CO{sub 2}/coal effects. The tests involving the Wyoming and New Mexico Coals are reported herein, and the tests involving the Illinois coal are described in Topical Report No. 2. On a laboratory scale, microautoclave tests evaluating coal, start-up oils, catalysts, thermal treatment, CO{sub 2} addition and sulfur compound effects were conducted and reported in Topical Report No. 3. Other microautoclave tests are described in the Bench Run sections to which they refer such as: rejuvenated catalyst, coker liquids and cleaned coals. The microautoclave tests conducted for modelling the CTSL{trademark} process are described in the CTSL{trademark} Modelling section of Topical Report No. 3 under this contract.

  20. Determination of bitumen and rubber content in bituminous mixes containing crumb tyre rubber; Determinacion del contenido de betum y de caucho en las mezclas bituminosas que incorporan plvo de caucho procedente de neumaticos fuera de uso

    Energy Technology Data Exchange (ETDEWEB)

    Rubio Guzamn, B.; Jimenez Saez, R.

    2009-07-01

    In recent years the use of crumb rubber from scrap tyres as a component of hot bituminous mixes for road construction, has been officially promoted by the Public Administration in Spain, by issuing several publications of both informative and normative nature, aimed to spread knowledge and experiences on the subject and also to specify the requirement and regulate the working applications for this material. However, it also seems necessary to develop new test methods which, allows control of the rubber content in crumb rubber-added mixes, regardless of the process (wet or dry) followed for the mix production. This article describes a procedure reliable enough to determine both the soluble bituminous binder and the rubber contents in bituminous mixes based on two combined, previously standardized test methods: binder extraction with solvent and ignition. (Author) 7 refs.

  1. Controls on coalbed methane potential and gas sorption characteristics of high-volatile bituminous coals in Indiana

    Science.gov (United States)

    Solano-Acosta, Wilfrido

    distribution, and adsorption experiments at high and low gas pressures are employed to estimate reservoir gas capacity and to characterize high volatile bituminous coals of Indiana for potential future CO2 sequestration. Understanding the mechanisms and geologic conditions that control the occurrence of gas in coal allows us to better characterize: (1) CBM reservoirs for their potential economic use, and (2) coal seams as future receptacles of anthropogenic carbon dioxide.

  2. Bituminous concrete overlay studies.

    Science.gov (United States)

    1971-01-01

    Deflection tests conducted on eight sections of primary highway, both before and after asphaltic concrete resurfacings, were analyzed as a study of the utility of such tests in the design of overlays. The application of tentative traffic and allowabl...

  3. Technical and economic assessment of process of treatment of coated bituminous sludge by combustion/vitrification (report PNGMDR 2013-2015)

    International Nuclear Information System (INIS)

    2015-01-01

    This note reports the assessment of a processing by combustion/vitrification of about 60.000 parcels of coated bituminous sludge belonging to intermediate-level long-lived and low-level long-lived category, and warehoused on the Marcoule CEA site. This assessment identifies the front-end cost of an exploratory R and D which would be required to undo technological locks, the cost of design, realisation and exploitation of the associated installation, and the negative features dues to the lack of technological maturity and to the management of environmental risks and impacts in comparison with the reference industrial solution (geological storage). As a conclusion, the authors state that the process is still not technically feasible

  4. Comparative study on combined co-pyrolysis/gasification of walnut shell and bituminous coal by conventional and congruent-mass thermogravimetric analysis (TGA) methods.

    Science.gov (United States)

    Zhang, Yan; Fan, Di; Zheng, Yan

    2016-01-01

    Combined co-pyrolysis/gasification of bituminous coal (BC) and walnut shell (WS) are comparatively studied with both conventional and congruent-mass thermogravimertric analysis (TGA) methods. The results indicate that BC and WS exhibit additivity in the co-pyrolysis step. However, the gasification reactivity of chars in subsequent gasification step exhibits remarkable sample-mass dependence, which causes the illusions in synergy and inhibition effects when conventional TGA tests are conducted. A congruent-mass TGA method has been developed to overcome the limitations of the conventional TGA mode. One of the advantages of this method is that it can reduce to a minimum the effect of sample mass on reactivity. Thus, the degree of synergy or inhibition can be directly estimated from the deviation of the experimental TG curves between the two separated and blended samples. We recommend this method in studying the co-processing behavior between coal and biomass. Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Real-time analysis of soot emissions from bituminous coal pyrolysis and combustion with a vacuum ultraviolet photoionization aerosol time-of-flight mass spectrometer.

    Science.gov (United States)

    Gao, Shaokai; Zhang, Yang; Meng, Junwang; Shu, Jinian

    2009-01-15

    This paper reports on-line analyses of the soot emissions from the Inner Mongolia bituminous coal combustion and pyrolysis processes with a vacuum ultraviolet photoionization aerosol time-of-flight mass spectrometer (VUV-ATOFMS). The soot particles are generated by heating a small amount of screened coal powder in synthetic air and nitrogen atmosphere in a tubular oven. The vacuum ultraviolet photoionization time-of-flight (VUV-TOF) mass spectra of the soot particles emitted from combustion and pyrolysis at different oven temperatures and different stages are obtained. The VUV-TOF mass spectra are assigned with the references of the results of the off-line GC/MS analysis.

  6. Thermodynamic analysis and economic evaluation of a 1000 MW bituminous coal fired power plant incorporating low-temperature pre-drying (LTPD)

    International Nuclear Information System (INIS)

    Xu, Cheng; Xu, Gang; Zhu, Mingming; Dong, Wei; Zhang, Yang; Yang, Yongping; Zhang, Dongke

    2016-01-01

    Highlights: • An improved design of coal pre-drying using flue gas waste heat was proposed. • 0.4% energy efficiency increase was achieved with the proposed system. • The additional net economic benefit of the proposed system is $1.91 M per year. • Proposed concept can be widely applied to improve coal-fired power plant efficiency. - Abstract: Low-temperature pre-drying (LTPD) of lignite has been identified as an effective approach to improve the efficiency of lignite fired power plants. In this study, an improved concept for the pre-drying of medium moisture bituminous coals using flue gas waste heat was proposed and its feasibility was assessed. In the proposed configuration, the boiler exhaust flue gas is drawn to dryers to heat and pre-dry the raw coal, removing a large proportion of the coal moisture and leading to an improvement in the energy efficiency of the power plant. Thermodynamic analysis and economic evaluation were performed based on a typical 1000 MW bituminous coal fired power plant incorporating the proposed LTPD concept. The results showed that the net power plant efficiency gain is as much as 0.4 percentage point with additional net power output of 9.3 MW as compared to the reference plant without coal pre-drying. This was attributed to the reduction in the moisture content from 10.3 to 2.7 wt%. The additional net economic benefit attained due to the coal pre-drying was estimated to reach $1.91 M per year. This work provides a broadly applicable and economically feasible approach to further improve the energy efficiency of power plants firing coals with medium moisture contents.

  7. Mathematical simulation of gas pressure in fibre-reinforced concrete container at radiation and biological decomposition of cellulose, bituminized and concrete radwastes

    International Nuclear Information System (INIS)

    Kuruc, J.; Kvito, P.

    2005-01-01

    Fibre-reinforced concrete container (FRCC) are used for long-time repository of radioactive wastes. Low- and middle-active radwastes from operation of the NPPs V-1, V-2 Jaslovske Bohunice, Mochovce NPP and from decommissioned NPP A-1 (Jaslovske Bohunice) are treated in the plant SE-VYZ in Jaslovske Bohunice and after immobilisation are deposited in National Radwaste Repository Mochovce (RU RAO). After filling of the RU RAO, FRCC will be stored during 300 years. During this time the integrity of the FRCC must be guaranteed. By the influence of autoradiolysis of the cellulose and bituminized radwastes as well as in cement grout the gases are formed, mainly the hydrogen, methane and carbon dioxide. In the case of presence of available water (a w ≥ 0.63) and in presence of microbes and moulds at appropriate conditions the biological decomposition of cellulose materials may proceed with formation of H 2 , CH 4 a CO 2 . With increasing of developed gases may increase pressure in FRCC, that may initiate the loss of integrity of the FRCC with following endangering of radiation safety of the RU RAO, respectively of the territory over the repository.Authors developed the new mathematical model of pressure of gases in FRCC and in deposited barrels with cellulose and bituminized radwastes. The mathematical model is based on biological decomposition of cellulose materials as well as on radiation decomposition of cellulose, bitumen and concrete. In this mathematical model the diffusion through the walls of FRCC is the main process responsible for decreasing of the pressure. This model was developed in two basic variants: (1) Mathematical model of gas pressure in FRCC as function of dose; (2) Mathematical model of gas pressure in FRCC as function of mass of cellulose

  8. Thermo-mechanical behavior of bituminous mixtures at low temperatures. Links between the binder characteristics and the mix properties; Comportement thermomecanique des enrobes bitumeux a basses temperatures: relations entre les proprietes du liant et de l'enrobe

    Energy Technology Data Exchange (ETDEWEB)

    Olard, F.

    2003-10-01

    This thesis has been realized within the framework of a partnership between the Ecole Nationale des TPE, APPIA and EUROVIA. The company Total has also been associated to this project. The study deals with the thermo-mechanical behavior of bituminous materials at low temperatures. The aim is to establish the links between the characteristics of the binder and the properties of bituminous mixes at low temperatures, and to better understand the existing low-temperature parameters and criteria for binders (or to propose new ones), related to the in-situ behavior of bituminous mixtures. A large experimental campaign has been carried out so as to fulfill this goal. After a bibliographical study on the rheology and the thermo-mechanical properties of (pure or modified) binders, putties and mixes, the experimental campaign carried out both in the small strain domain and in the large strain domain, is presented. The low temperature behavior of binders has been evaluated with three common fundamental tests: i)the complex modulus determination, ii)the Bending Beam Rheometer and iii)the tensile strength at a constant strain rate and constant temperatures. A new three point bending test on pre-notched bitumen beams has also been developed at the ENTPE. The low-temperature fracture properties of bitumens were studied at constant temperatures and cross-head speeds considering the Linear Elastic Fracture Mechanics (LEFM) assumptions. The thermo-mechanical behavior of bituminous mixtures has been studied by performing i)complex modulus tests, ii)measurements of the coefficient of thermal dilatation and contraction, iii)tensile tests at constant temperatures and strain rates, and iv)Thermal Stress Restrained Specimen Tests. Apart from the determination of some pertinent links between binder and mix properties and discriminating characteristics with regard to the thermal cracking of bituminous mixes at low temperatures, the analysis has also consisted in modeling the behavior of

  9. Effect of the temperature of different combustion zones in the boiler grate on changes in physical and chemical parameters of bituminous coal and slags

    Directory of Open Access Journals (Sweden)

    Przemysław Rompalski

    2016-01-01

    Full Text Available This paper presents the results of a study on the influence of the temperature of characteristic zones of coal combustion in a stoker fired boiler (drying, degassing, and burn-out, on changes in physical and chemical parameters of bituminous coal and slags. This information is important as it helps identify the impact of coal properties on the accumulation of trace elements, primarily mercury, in combustion waste. The study is the continuation of research work on the impact of mercury compounds accumulated in combustion waste on the natural environment (mercury from landfills of slag, and fly ash. Studies were undertaken because no in-depth analysis of the impact of the temperature of particular zones of stoker fired boilers on the physical and chemical parameters of the post-process slag, including mercury content, had been reported in literature. Both of the coals examined, classified as bituminous coal according to the International Classification of Seam Coals and of type 32.1 according to the PN-G-97002:1982 standard, showed an average mercury content of 0.0849 μg/g. In the chemical composition determined for the ash derived from burnt coal, the dominance of SiO2 and Al2O3 over other oxides was found. This feature results in the increase of the softening temperature and ash melting and, therefore, during the combustion of coal tested in a stoker fired boiler, only ash was subjected to the sintering process. Mercury content in the other examined samples taken from various locations of the stoker fired boiler (drying – 32–1050 °C, degassing – 1050–1020 °C, and burn-out – 1020–400 °C varied from 0.0668 to 0.0009 μg/g and was determined with the use of a LECO atomic absorption spectrometer. The analyses of the elemental composition, performed with the application of XRF spectrometry, for ash obtained from samples collected from different sampling points of the stoker fired boiler showed that the largest concentration of

  10. Mercury emissions during cofiring of sub-bituminous coal and biomass (chicken waste, wood, coffee residue, and tobacco stalk) in a laboratory-scale fluidized bed combustor.

    Science.gov (United States)

    Cao, Yan; Zhou, Hongcang; Fan, Junjie; Zhao, Houyin; Zhou, Tuo; Hack, Pauline; Chan, Chia-Chun; Liou, Jian-Chang; Pan, Wei-Ping

    2008-12-15

    Four types of biomass (chicken waste, wood pellets, coffee residue, and tobacco stalks) were cofired at 30 wt % with a U.S. sub-bituminous coal (Powder River Basin Coal) in a laboratory-scale fluidized bed combustor. A cyclone, followed by a quartz filter, was used for fly ash removal during tests. The temperatures of the cyclone and filter were controlled at 250 and 150 degrees C, respectively. Mercury speciation and emissions during cofiring were investigated using a semicontinuous mercury monitor, which was certified using ASTM standard Ontario Hydra Method. Test results indicated mercury emissions were strongly correlative to the gaseous chlorine concentrations, but not necessarily correlative to the chlorine contents in cofiring fuels. Mercury emissions could be reduced by 35% during firing of sub-bituminous coal using only a quartz filter. Cofiring high-chlorine fuel, such as chicken waste (Cl = 22340 wppm), could largely reduce mercury emissions by over 80%. When low-chlorine biomass, such as wood pellets (Cl = 132 wppm) and coffee residue (Cl = 134 wppm), is cofired, mercury emissions could only be reduced by about 50%. Cofiring tobacco stalks with higher chlorine content (Cl = 4237 wppm) did not significantly reduce mercury emissions. This was also true when limestone was added while cofiring coal and chicken waste because the gaseous chlorine was reduced in the freeboard of the fluidized bed combustor, where the temperature was generally below 650 degrees C without addition of the secondary air. Gaseous speciated mercury in flue gas after a quartz filter indicated the occurrence of about 50% of total gaseous mercury to be the elemental mercury for cofiring chicken waste, but occurrence of above 90% of the elemental mercury for all other cases. Both the higher content of alkali metal oxides or alkali earth metal oxides in tested biomass and the occurrence of temperatures lower than 650 degrees C in the upper part of the fluidized bed combustor seemed to be

  11. Flow sheet at Lu-Op plant for auto gasoline for 170/sup 0/ E. P. gasoline for DHD from bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    1942-11-02

    Several tables with varied information concerning gasoline production are presented. The first table concerned the 700 atm liquid phase running to produce: (1) gasoline and middle oil or (2) 32% heavy oil excess. This gave information such as the rate of primary crusing, drying, paste milling and pressing, gas circulation, oil washing, compression, centrifuge plant operations, kiln plant operations, cold catchpot products, and yields. It also gave stall sizes. The second and third charts contained information for the 300 atm and 700 atm vapor phase processes with subdivisions for auto gasoline and 170/sup 0/C endpoint gasoline. It showed rates for injection pumps, gas circulation, compression, yield from columns, L.P.G. production, gasoline stabilization and wash, hydrogenation gas production with 95% recovery, percent of aromatic recovery, and total hydrogen consumption. The fourth chart concerned hydrogen production for the Lu-Op plant from bituminous coal. The first major category was coke with subcategories of DHD gasoline in the 700 atm vapor phase system and in the 300 atm vapor phase system. The second category was hydrogenation gas splitting with the same subcategories as above. A table of power requirements for 170/sup 0/C endpoint gasoline including the liquid phase and hydrogen production for 300 atm and 700 atm vapor phase processes is included. 5 tables

  12. Rapid co-pyrolysis of rice straw and a bituminous coal in a high-frequency furnace and gasification of the residual char.

    Science.gov (United States)

    Yuan, Shuai; Dai, Zheng-hua; Zhou, Zhi-jie; Chen, Xue-li; Yu, Guang-suo; Wang, Fu-chen

    2012-04-01

    Rapid pyrolysis of rice straw (RS) and Shenfu bituminous coal (SB) separately, and rapid co-pyrolysis of RS/SB blends (mass ratio 1:4, 1:4, and 4:1), were carried out in a high-frequency furnace which can ensure both high heating rate and satisfying contact of fuel particles. Synergies between RS and SB during rapid co-pyrolysis were investigated. Intrinsic and morphological structures of residual char from co-pyrolysis, and their effects on gasification characteristics were also studied. Synergies occurred during rapid co-pyrolysis of RS and SB (RS/SB=1:4) resulting in decreasing char yields and increasing volatile yields. Synergies also happened during gasification of the char derived from co-pyrolysis of RS and SB with mass ratio of 1:4. The increased mass ratio of RS to SB did not only weaken synergies during co-pyrolysis, but significantly reduced the gasification rates of the co-pyrolysis char compared to the calculated values. Results can help to optimize co-conversion process of biomass/coal. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. Analysis of Porous Structure Parameters of Biomass Chars Versus Bituminous Coal and Lignite Carbonized at High Pressure and Temperature—A Chemometric Study

    Directory of Open Access Journals (Sweden)

    Adam Smoliński

    2017-09-01

    Full Text Available The characteristics of the porous structure of carbonized materials affect their physical properties, such as density or strength, their sorption capacity, and their reactivity in thermochemical processing, determining both their applicability as fuels or sorbents and their efficiency in various processes. The porous structure of chars is shaped by the combined effects of physical and chemical properties of a carbonaceous material and the operating parameters applied in the carbonization process. In the study presented, the experimental dataset covering parameters of various fuels, ranging from biomass through lignite to bituminous coal, and chars produced at 1273 K and under the pressure of 1, 2, 3, and 4 MPa was analyzed with the application of the advanced method of data exploration. The principal component analysis showed that the sample of the highest coal rank was characterized by lower values of parameters reflecting the development of the porous structure of chars. A negative correlation was also observed between the carbon content in a fuel and the evolution of the porous structure of chars at high pressure. The highest total pore volume of chars produced under 1 and 3 MPa and the highest micropore surface area under 3 MPa were reported for a carbonized fuel sample of the highest moisture content.

  14. Changes in optical properties, chemistry, and micropore and mesopore characteristics of bituminous coal at the contact with dikes in the Illinois Basin

    Science.gov (United States)

    Mastalerz, Maria; Drobniak, A.; Schimmelmann, A.

    2009-01-01

    Changes in high-volatile bituminous coal (Pennsylvanian) near contacts with two volcanic intrusions in Illinois were investigated with respect to optical properties, coal chemistry, and coal pore structure. Vitrinite reflectance (Ro) increases from 0.62% to 5.03% within a distance of 5.5??m from the larger dike, and from 0.63% to 3.71% within 3.3??m from the small dike. Elemental chemistry of the coal shows distinct reductions in hydrogen and nitrogen content close to the intrusions. No trend was observed for total sulfur content, but decreases in sulfate content towards the dikes indicate thermochemical sulfate reduction (TSR). Contact-metamorphism has a dramatic effect on coal porosity, and microporosity in particular. Around the large dike, the micropore volume, after a slight initial increase, progressively decreases from 0.0417??cm3/g in coal situated 4.7??m from the intrusive contact to 0.0126??cm3/g at the contact. Strongly decreasing mesopore and micropore volumes in the altered zone, together with frequent cleat and fracture filling by calcite, indicate deteriorating conditions for both coalbed gas sorption and gas transmissibility. ?? 2008 Elsevier B.V. All rights reserved.

  15. Changes in optical properties, chemistry, and micropore and mesopore characteristics of bituminous coal at the contact with dikes in the Illinois Basin

    Energy Technology Data Exchange (ETDEWEB)

    Mastalerz, M.; Drobniak, A. [Indiana University, Indiana Geological Survey, Bloomington, IN 47405 (United States); Schimmelmann, A. [Indiana University, Dept. of Geological Sciences, Bloomington, IN 47405-1405 (United States)

    2009-01-31

    Changes in high-volatile bituminous coal (Pennsylvanian) near contacts with two volcanic intrusions in Illinois were investigated with respect to optical properties, coal chemistry, and coal pore structure. Vitrinite reflectance (R{sub o}) increases from 0.62% to 5.03% within a distance of 5.5 m from the larger dike, and from 0.63% to 3.71% within 3.3 m from the small dike. Elemental chemistry of the coal shows distinct reductions in hydrogen and nitrogen content close to the intrusions. No trend was observed for total sulfur content, but decreases in sulfate content towards the dikes indicate thermochemical sulfate reduction (TSR). Contact-metamorphism has a dramatic effect on coal porosity, and microporosity in particular. Around the large dike, the micropore volume, after a slight initial increase, progressively decreases from 0.0417 cm{sup 3}/g in coal situated 4.7 m from the intrusive contact to 0.0126 cm{sup 3}/g at the contact. Strongly decreasing mesopore and micropore volumes in the altered zone, together with frequent cleat and fracture filling by calcite, indicate deteriorating conditions for both coalbed gas sorption and gas transmissibility. (author)

  16. Evaluation of Control Strategies to Effectively Meet 70-90% Mercury Reduction on an Eastern Bituminous Coal Cyclone Boiler with SCR

    Energy Technology Data Exchange (ETDEWEB)

    Tom Campbell

    2008-12-31

    This is the final site report for testing conducted at Public Service of New Hampshire's (PSNH) Merrimack Unit 2 (MK2). This project was funded through the DOE/NETL Innovations for Existing Plants program. It was a Phase III project with the goal to develop mercury control technologies that can achieve 50-70% mercury capture at costs 25-50% less than baseline estimates of $50,000-$70,000/lb of mercury removed. While results from testing at Merrimack indicate that the DOE goal was partially achieved, further improvements in the process are recommended. Merrimack burned a test blend of eastern bituminous and Venezuelan coals, for a target coal sulfur content of 1.2%, in its 335-MW Unit 2. The blend ratio is approximately a 50/50 split between the two coals. Various sorbent injection tests were conducted on the flue gas stream either in front of the air preheater (APH) or in between the two in-series ESPs. Initial mercury control evaluations indicated that, without SO3 control, the sorbent concentration required to achieve 50% control would not be feasible, either economically or within constraints specific to the maximum reasonable particle loading to the ESP. Subsequently, with SO{sub 3} control via trona injection upstream of the APH, economically feasible mercury removal rates could be achieved with PAC injection, excepting balance-of-plant concerns. The results are summarized along with the impacts of the dual injection process on the air heater, ESP operation, and particulate emissions.

  17. Pyrolysis and liquefaction of acetone and mixed acetone/ tetralin swelled Mukah Balingian Malaysian sub-bituminous coal-The effect on coal conversion and oil yield

    International Nuclear Information System (INIS)

    Mohd Pauzi Abdullah; Mohd Azlan Mohd Ishak; Khudzir Ismail

    2008-01-01

    The effect of swelling on Mukah Balingian (MB) Malaysian sub-bituminous coal macrostructure was observed by pyrolysing the swelled coal via thermogravimetry under nitrogen at ambient pressure. The DTG curves of the pyrolyzed swelled coal samples show the presence of evolution peaks at temperature ranging from 235 - 295 degree Celsius that are due to releasing of light molecular weight hydrocarbons. These peaks, however, were not present in the untreated coal, indicating some changes in the coal macrostructure has occurred in the swelled coal samples. The global pyrolysis kinetics for coal that follows the first-order decomposition reaction was used to evaluate the activation energy of the pyrolyzed untreated and swelled coal samples. The results thus far have shown that the activation energy for the acetone and mixed acetone/ tetralin-swelled coal samples exhibit lower values than untreated coal, indicating less energy is required during the pyrolysis process due to the weakening of the coal-coal macromolecular interaction network. Moreover, liquefaction on the swelled coal samples that was carried out at temperatures ranging from 360 to 450 degree Celsius at 4 MPa of nitrogen pressure showed the enhancement of the coal conversion and oil yield at temperature of 420 degree Celsius, with retrogressive reaction started to dominate at higher temperature as indicated by decreased and increased in oil yield and high molecular weight pre-asphaltene, respectively. These observations suggest that the solvent swelling pre-treatment using acetone and mixed acetone/ tetralin can improve the coal conversion and oil yields at less severe liquefaction condition. (author)

  18. Development of new non destructive methods for bituminized radioactive waste drums characterization; Developpement de nouvelles methodes de caracterisation non destructive pour des dechets radioactifs enrobes dans du bitume

    Energy Technology Data Exchange (ETDEWEB)

    Pin, P

    2004-10-15

    Radioactive waste constitute a major issue for the nuclear industry. One of the key points is their characterization to optimize their management: treatment and packaging, orientation towards the suited disposal. This thesis proposes an evaluation method of the low-energy photon attenuation, based on the gamma-ray spectra Compton continuum. Effectively, the {sup 241}Am measurement by gamma-ray spectrometry is difficult due to the low energy of its main gamma-ray (59.5 keV). The photon attenuation strongly depends on the bituminous mix composition, which includes very absorbing elements. As the Compton continuum also depends on this absorption, it is possible to link the 59.5 keV line attenuation to the Compton level. Another technique is proposed to characterize uranium thanks to its fluorescence X-rays induced by the gamma emitters already present in the waste. The uranium present in the drums disturbs the neutron measurements and its measurement by self-induced X-ray fluorescence allows to correct this interference. Due to various causes of error, the total uncertainty is around 50 % on the activity of the radioisotope {sup 241}Am, corrected by the peak to Compton technique. The same uncertainty is announced on the uranium mass measured by self induced X-ray fluorescence. As a consequence of these promising results, the two methods were included in the industrial project of the 'Marcoule Sorting Unit'. One major advantage is that they do not imply any additional material because they use information already present in the gamma-ray spectra. (author)

  19. Thermal relaxation of bituminous coal to improve donation ability of hydrogen radicals in flash pyrolysis; Sekitan kozo kanwa ni yoru suiso radical kyoyo noryoku no kojo wo mezashita netsubunkai mae shori

    Energy Technology Data Exchange (ETDEWEB)

    Mori, T.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In terms of coal conversion reaction, the behavior of bituminous coal heated beyond a glass transition point was examined on the basis of pyrolyzed products, and the effect of an increase in proton mobility on promotion of coal decomposition was evaluated. In experiment, after Illinois bituminous coal specimen was heated up to a specific temperature in N2 or He gas flow at a rate of 5K/min, the specimen was directly transferred to a pyrolyzer for instantaneous pyrolysis. As the experimental result, the glass transition temperature of the Illinois coal specimen was calculated to be 589K from a differential scanning calorimetry (DSC) profile. From the pyrolysis result of the Illinois coal specimen heated up to 623K, the char yield decreased by 3kg as compared with that of the original coal, while the tar yield increased by 4kg up to 27kg per 100kg of the original coal. This tar increase was larger than that of cooled coal. These results suggested that the donation of hydrogen radicals to coal fragments is improved with an increase in proton mobility. 4 refs., 4 figs., 1 tab.

  20. Study of stabilization/solidification processes (of solid porous wastes) based on hydraulic or bituminous binders; Etude des procedes de stabilisation/solidification (des dechets solides poreux) a base de liants hydrauliques ou de liants bitumineux

    Energy Technology Data Exchange (ETDEWEB)

    Sing-Teniere, Ch.

    1998-02-01

    The first part of this thesis presents the regulatory framework and the technical context linked with the study of stabilized/solidified wastes and with the evaluation of stabilization/solidification processes. A presentation of the two type of ultimate wastes under study (a used catalyst and an activated charcoal) and an analysis of the processes is given. The second part is devoted to the experimental characterization of both types of porous wastes. The third part deals with the processing of such wastes using an hydraulic binder. The study stresses on both on the stabilization/solidification efficiency of the process and on the conditions of its implementation. The same work is made for a process that uses a bituminous binder. Some choice criteria for the selection of the better process are deduced from the examination of the overall data collected. The waste characterization methodology is applied six times: two times for the raw wastes, two times for the same wastes processed with an hydraulic binder, and two times for the same wastes processed with a bituminous binder. (J.S.)

  1. Hydrogenation balances for bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Hoelscher

    1944-02-11

    This report was intended to set up predictive curves concerning how certain variables involved in coal hydrogenation output would change in response to changes in certain operational or input variables, for hydrogenation of Gelsenberg coal. The particular dependences investigated in the article were the following: (1) for liquid phase, the dependence of oil output, amount of product to be distilled, and hydrogen use upon the ash content of the coal, the carbon content of the coal, and the percentage of formation of gases, and (2) for vapor phase, the dependence of gasoline yield, hydrogen use, and excess hydrocarbon gas products on the percentage of gasification in the 6434 step. Within certain limits of validity, these dependences seemed mostly to be linear and were illustrated in graphs in the report (most of which were very hard to read on the microfilm image). The limits of validity were 2 to 8% ash content, 80 to 86.2% carbon content, 20 to 25% gasification in liquid phase, and 17 to 25% gasification in the 6434 vapor phase. As an example of the data and calculations, it was observed that at 2% ash content, there was 628 kg of oil output in the liquid phase, at 4% ash content, there was 621 kg oil output, and at 8% ash content, there was 607 kg oil output, so it was calculated that oil output would decrease by 0.56% for each percent increase in ash content between 2% and 8%. 7 tables, 2 graphs.

  2. Dust is the dominant source of "heavy metals" to peat moss (Sphagnum fuscum) in the bogs of the Athabasca Bituminous Sands region of northern Alberta.

    Science.gov (United States)

    Shotyk, William; Bicalho, Beatriz; Cuss, Chad W; Duke, M John M; Noernberg, Tommy; Pelletier, Rick; Steinnes, Eiliv; Zaccone, Claudio

    2016-01-01

    Sphagnum fuscum was collected from twenty-five ombrotrophic (rain-fed) peat bogs surrounding open pit mines and upgrading facilities of Athabasca Bituminous Sands (ABS) in northern Alberta (AB) in order to assess the extent of atmospheric contamination by trace elements. As a control, this moss species was also collected at a bog near Utikuma (UTK) in an undeveloped part of AB and 264km SW of the ABS region. For comparison, this moss was also collected in central AB, in the vicinity of the City of Edmonton which is approximately 500km to the south of the ABS region, from the Wagner Wetland which is 22km W of the City, from Seba Beach (ca. 90km W) and from Elk Island National Park (ca. 45km E). All of the moss samples were digested and trace elements concentrations determined using ICP-SMS at a commercial laboratory, with selected samples also analyzed using instrumental neutron activation analysis at the University of Alberta. The mosses from the ABS region yielded lower concentrations of Ag, As, Bi, Cd, Cu, Pb, Sb, Tl, and Zn compared to the moss from the Edmonton area. Concentrations of Ni and Mo in the mosses were comparable in these two regions, but V was more abundant in the ABS samples. Compared with the surface vegetation of eight peat cores collected in recent years from British Columbia, Ontario, Quebec and New Brunswick, the mean concentrations of Ag, As, Bi, Cd, Cu, Mo, Ni, Pb, Sb, Tl and Zn in the mosses from the ABS region are generally much lower. In fact, the concentrations of these trace elements in the samples from the ABS region are comparable to the corresponding values in forest moss from remote regions of central and northern Norway. Lithophile element concentrations (Ba, Be, Ga, Ge, Li, Sc, Th, Ti, Zr) explain most of the variation in trace metal concentrations in the moss samples. The mean concentrations of Th and Zr are greatest in the moss samples from the ABS region, reflecting dust inputs to the bogs from open pit mines, aggregate

  3. Microbial activity in argillite waste storage cells for the deep geological disposal of French bituminous medium activity long lived nuclear waste: Impact on redox reaction kinetics and potential

    Science.gov (United States)

    Albrecht, A.; Leone, L.; Charlet, L.

    2009-04-01

    Micro-organisms are ubiquitous and display remarkable capabilities to adapt and survive in the most extreme environmental conditions. It has been recognized that microorganisms can survive in nuclear waste disposal facilities if the required major (P, N, K) and trace elements, a carbon and energy source as well as water are present. The space constraint is of particular interest as it has been shown that bacteria do not prosper in compacted clay. An evaluation of the different types of French medium and high level waste, in a clay-rich host rock storage environment at a depth between 500 and 600 m, has shown that the bituminous waste is the most likely candidate to accommodate significant microbial activity. The waste consists of a mixture of bitumen (source of bio-available organic matter and H2 as a consequence of its degradation and radiolysis) and nitrates and sulphates kept in a stainless steel container. The assumption, that microbes only have an impact on reaction kinetics needs to be reassessed in the case where nitrates and sulphates are present since both are known not to react at low temperatures without bacterial catalysis. The additional impact of both oxy-anions and their reduced species on redox conditions, radionuclide speciation and mobility gives this evaluation their particular relevance. Storage architecture proposes four primary waste containers positioned into armoured cement over packs and placed with others into the waste storage cell itself composed of a cement mantle enforcing the argillite host rock, the latter being characterized by an excavation damaged zone constricted both in space and in time and a pristine part of 60 m thickness. Bacterial activity within the waste and within the pristine argillite is disregarded because of the low water activity (colonies is the high pH controlled by the cement solution. Archea are able to survive at high pH, when hydrogen gas is available as an energy sources; they are therefore likely candidates

  4. Bituminous coal production in the Appalachian basin: past, present, and future: Chapter D.3 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Science.gov (United States)

    Milici, Robert C.; Polyak, Désirée E.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    Although small quantities of coal first were produced from the Appalachian basin in the early 1700s, the first production statistics of significance were gathered during the census of 1830 (Eavenson, 1942). Since then, about 35 billion short tons of bituminous coal have been produced from the Appalachian basin from an original potential coal reserve (PCR(o)) estimated to range from about 60 to 90 billion short tons. The term “reserve” refers to economically producible coal, and a “potential coal reserve” (PCR(n)) is an estimate of the amount of coal economically recoverable in a region (State, coal field) over a defined time period (n = number of years) and under a range of economic, societal, and technological conditions. Thus, the current cumulative production plus the PCR(n) equals an estimated cumulative production (ECP(n)). The maps in this report (oversized figures 1, 2, 3, and 4) were produced from a digital database of historical and current coal production records by county. Sources of the original data include various State geological surveys, the U.S. Geological Survey, the former U.S. Bureau of Mines, and the U.S. Department of Energy’s Energy Information Administration. This report is part of the U.S. Geological Survey’s National Coal Resource Assessment Project.

  5. Influence of natural weathering of two medium-volatile bituminous coals of similar rank on coke quality; Influencia de la alteracion meteorica de dos carbones coquizables con contenido medio de materia volatil en la calidad del coque producido

    Energy Technology Data Exchange (ETDEWEB)

    Casal, M.D.; Diez, M.A.; Alvarez, R.; Barriocanal, C.; Canga, C.S.; Pis, J.J. [Instituto Nacional del Carbon. Oviedo (Spain)

    1998-06-01

    The study of the weathering of the two bituminous coals stored at the INCAR stockyard and its influence on coke quality is presented. These coals of similar rank are present in industrial blends used by the Corporation Siderurgica Integral (CSI) for the production of blast-furnace coke. Of all the techniques used to determine the degree of weathering, via thermoplastic properties. Gieseler plastometry was found to be the most sensitive. Coking tests were carried out in the semi-industrial coking plant at INCAR. The effect of weathering on each coal series is completely different. Weathering produces a loss of maximum fluidity accompanied by a decrease in aliphatic hydrogen in both coals. However, the los rate is different in each case. Coke quality clearly decreases in one, while in the other improves at first but then gradually deteriorates. An improvement in coke quality due to weathering not only affects some high-volatile coals as it is well known but also medium-volatile coals. (Author) 16 refs.

  6. Cellulose-containing Waste and Bituminized Salts

    International Nuclear Information System (INIS)

    Valcke, E.

    2005-01-01

    In Belgium, Medium-Level radioactive Waste (MLW) would be eventually disposed off in an underground repository in a geological formation such as the Boom Clay, which is studied as a reference host rock formation. MLW contains large quantities of non-radioactive chemicals that are released upon contact with pore water. It could be the case, for instance, for plutonium bearing cellulosic waste - such as paper tissues used to clean alpha glove boxes - issued from nuclear fuel fabrication (Belgonucleaire). At high pH, as in a disposal gallery backfilled with cement, the chemical degradation of cellulose will generate water-soluble products that may form strong complexes with actinides such as Am, Pu, Np, and U. This could lower the sorption of these elements onto the clay minerals, and hence increase their migration through the clay barrier. Another chemical perturbation could occur from the 3000 m 3 of so-called Eurobitum bituminised MLW, with precipitation sludges from the chemical treatment of spent nuclear fuel, and containing about 750 tons of NaNO 3 . The presence of NaNO 3 in this waste will give rise to several processes susceptible to affect the safety of the disposal system. Amongst others, it is necessary to verify that the swelling pressure of bitumen on the gallery wall and the osmotic pressure within the near-field are not too high to induce a fissuration of the host rock, leading to the formation of preferential migration pathways. The major objective of our work is to obtain a broad understanding of the different processes induced by the release of non-radioactive chemicals in the clay formation, to assess the chemical compatibility of different MLW forms with the clay

  7. Development of New Bituminous Pavement Design Method

    DEFF Research Database (Denmark)

    Ullidtz, Per

    The report and work of COST Action 333 sets in place the foundation for a coherent, cost-effective and harmonised European pavement design method. In order to do this, the work programme focused on information gathering, identification of requirements and the selection of the necessary design...

  8. Deformation Properties and Fatigue of Bituminous Mixtures

    Directory of Open Access Journals (Sweden)

    Frantisek Schlosser

    2013-01-01

    Full Text Available Deformation properties and fatigue performance are important characteristics of asphalt bound materials which are used for construction of pavement layers. Viscoelastic asphalt mixtures are better characterized via dynamic tests. This type of tests allows us to collate materials with regard to axle vibrations which lie usually in the range of 6 Hz–25 Hz for standard conditions. Asphalt modified for heat sensitivity in the range from −20°C to +60°C has significant impact on the overall characteristics of the mixture. Deformation properties are used as inputs for empirical mixture design, and fatigue performance of asphalt mixtures reflects the parameters of functional tests. Master curves convey properties of asphalt mixtures for various conditions and allow us to evaluate them without the need of time expensive testing.

  9. Bituminization of liquid radioactive wastes. Part 2

    International Nuclear Information System (INIS)

    Gradev, G.D.; Ivanov, V.I.; Stefanova, I.G.; Milusheva, A.G.; Guteva, E.S.; Stefanov, G.I.; G'oshev, G.S.

    1991-01-01

    The leaching of alcaline cations, as well as of chloride, sulphate and borate anions and radionuclides was studied. The leach rates and the diffusion coefficients of some of the incorporated ions for the salt-bitumen products obtained from Bulgarian bitumens (road bitumen PB 66/90 and hydroinsulating bitumen HB 80/25) and salts (chlorides, sulphates, borates, salt mixtures modelling the concentrate from the evaporators at the Kozloduy NPP and radionuclides) were determined. Most suitable for technological research under the conditions of the Kozloduy NPP proved to be the road bitumen PB 66/90 with softening temperature at 48 o C. The optimum bitumen/salt ratio is found to be about 1.2. Admixtures of natural inorganic sorbents (clinoptiolite, vermiculite and bentonite) in quantities of 5-10% are found to decrease the leaching of radionuclides from the bitumen products. The action of the hydromica vermiculite is particularly pronounced. 6 tabs., 5 refs

  10. Calorific efficiency of bituminous coal hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Wilde, H.; Schappert, H.

    1942-02-20

    The calorific efficiency of coal hydrogenation was the relation between the calories contained in the desired final product, that is, gasoline and liquefied petroleum gas (L.P.G.), and the calories contained in the coal required to produce the desired final product. A table of the efficiency of the power plant was given. Calorific efficiency of hydrogen production was then discussed, with figure 1 showing the heat flow diagram; tables 1 and 2 contained data for the coke plant and the water gas plant, respectively. Calorific efficiency of hydrogenation proper was discussed, with figure 2 showing the heat flow diagram for the production of aviation gasoline, and with the corresponding energy values given in table 3. The next topic of discussion was the possibility of increasing the calorific efficiency of total hydrogenation by: introduction of Linde process, utilization of kiln residues, introduction of paste heat exchange, and recovering the waste heat from the hot letdown and products. Table 4 gave data on the hydrogenation for aviation gasoline. The efficiency of hydrogen production was 26.3% without counting possible improvements or by-products for the process. The efficiency of the hydrogenation process itself was 49.0% for production of aviation gasoline and 51.1% for production of auto gasoline. However, for combined hydrogenation and hydrogen production, the efficiencies became 27.2% and 28.9% respectively. If all of the improvements mentioned above (including hydrogen production by Linde-process decomposition of product gases) were introduced, the efficiencies would rise to about 34.6% and 36.8%, respectively. 5 diagrams, 4 tables

  11. Solar Radiation effect on the bituminous binder

    International Nuclear Information System (INIS)

    Tadeo Rico, A.; Torres Perez, A.

    2010-01-01

    Asphalt, used as binder in road construction, becomes more brittle and harder during working life on the surface of the road pavement, conducting toward their deterioration. This is caused by the oxidation of the molecular functional groups of the asphalt molecular structure. Moreover, it is observed that ultraviolet radiation increases the oxidation process. However, the effect of solar light on the asphalt degradation has been poorly researched. The aim of this work is to study asphalt ageing caused by effect of solar radiation, by using standard test. Four commercial asphalts from different companies were selected: two with penetration number 50/70, and the other two polymer modified asphalts. From each of the asphalts forty samples were taken off and placed in four different aging conditions of temperature and radiation for a period ranging from 40 to 500 days. Ring and Ball test, and Fraass breaking Point test, were used to analyse the changes of asphalt properties after exposition to solar radiation. The results of the four analyzed asphalts showed a distinct behaviour; not only in the test temperature increase but also in the rate. Another experiment was carried out. Samples from a hot mix asphalt batch were placed under solar radiation, and were compacted by the Marshall procedure after increasing periods of time. Density and resistance to plastic flow using Marshall Apparatus were measured. Results showed an increase in the stability of samples under radiation. Both experiments show that the solar radiation is enough to cause changes in the asphalt molecular structure due to oxidation. So that, the study of the effect of the solar radiation on the asphalt properties could be a good tool to asses the performances of asphalt pavement. (Author) 26 refs.

  12. The Role of Bituminous Sands in Extending the Petroleum Era Beyond 2000 A. D. (Summary Le rôle des sables bitumineux pour prolonger l'ère du pétrole au-delà de l'an 2000 (résumé

    Directory of Open Access Journals (Sweden)

    Carrigy M.

    2006-10-01

    Full Text Available Bituminous sand is an energy resource that is receiving increasing attention and there is a strong interest by the international community in co-operating in the development of new methods of exploration, and in the solution of common technological problems to reduce the time when oil from this enormous energy source is available. A detailed knowledge of the geological setting and the reservoir is of paramount importance to the assessment of the magnitude of the resource, its successful exploitation and to facilitate the transfer of the highly complicated recovery technology from one deposit to another. Much research also remains to be done to improve our understanding of the origin of the bitumen and the factors controlling the location of its accumulation. Based on the scant information we have, it is estimated that bituminous sand deposits contain from 5 to 10 x 10. 12 (trillion barrels of crude bitumen and are surely large enough to make a significant contribution to extending the petroleum era until alternative energy sources are developed. However, great amounts of synthetic oil from this source will probably not be brought onto the market until after the year 2000 A. D. because of the high capital cost, and large numbers of skilled technicians required to bring them into production. In the more industrialized nations where the demand for portable liquid fuel is strongest, notably Canada, Venezuela, and USA, billions of dollars are being spent on exploring and exploiting their bituminous sand resources. It is, however, in those undeveloped nations, who cannot afford to buy light crude oil, and who have bituminous deposits, where exploitation of this resource should have its greatest impact. It is therefore imperative that all geologists be aware of the new technologies that are now available to turn these low-grade hydrocarbons into high-grade products. Une attention croissante est accordée aux sables bitumineux comme source d

  13. Report on results for fiscal 1997 (B edition) on development of coal liquefaction technology. Development of bituminous coal liquefaction technology (research by pilot plant) 1/2; 1997 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu) 2/2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    This paper reports the operation of a pilot plant of a bituminous coal liquefaction technology as the 1/2 report. The operation research of the Run-2 through the Run-4-2 was conducted using, as the material, tanitoharum coal which is operating basis coal. The Run-2 achieved a coal charging continuous operation for 42 days. During the operation of 80% slurry supply load, various data were obtained including material balance under the NEDOL standard liquefaction conditions, with a liquefaction yield of 54% daf coal achieved. Steam blowing into the heating tube was found effective as measures to cope with coking generation in the heating furnace of a vacuum distillation tower. The softening point of liquefaction residuals was improved to 178 degrees C through the extracting adjustment of reduced pressure heavy gravity light oil fraction for washing. The Run-3/4-1 achieved a plant load ratio of 100% and a long-term coal charging continuous operation for 80 days, while the Run-3 achieved a slurry supply load of 100% under the NEDOL standard liquefaction conditions. The Run-4-1 achieved a high liquefaction yield of 58wt% daf coal. Performance was confirmed of a neutron beam source irradiation apparatus/measuring system and a tracer injection equipment. (NEDO)

  14. Characterizing volumetric deformation behavior of naturally occuring bituminous sand materials

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2009-05-01

    Full Text Available indicated that the considerable amount of bitumen in the oil sands, high applied loads from mining equipment and seasonal changes in temperature are major fac- tors that control the modulus and deformation behavior of oil sands (Joseph 2002). To date... angle and cohesion are the material properties used for modeling the strength and stiffness behavior. Bulk modulus is an important material property that describes the resistance to volume change when an element of soil is subjected to hydrostat- ic...

  15. Shear strength properties of naturally occurring bituminous sands

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2009-06-01

    Full Text Available on the oil sand materials with bitumen contents of 8.5%, 13.3% and 14.5% at 20C and 30C test temperatures. Results from the two tests could not be effectively compared since the triaxial tests produced zero fric-tion angles for all the oil sand materials...

  16. Permanent deformation behavior of naturally occurring bituminous sands

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2008-01-01

    Full Text Available were compacted close to field densities and then tested for permanent deformation at two temperatures using a newly proposed test procedure. The procedure applied stress states and ratios determined from field-loading characteristics of haul trucks...

  17. Advanced testing and characterization of transportation soils and bituminous sands

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2007-12-01

    Full Text Available , Illinois Doctoral Committee: Associate Professor Erol Tutumluer, Chair Professor Imad L. Al-Qadi Professor Emeritus Samuel H. Carpenter Professor Emeritus Marshall R. Thompson Dr. Liqun Chi, Caterpillar Inc., Peoria, IL ii ABSTRACT... ................................................................. 30 2.5 Review of Wheel-Soil Interaction Models ........................................................... 35 2.5.1 Vertical Stress-Displacement (Pressure-Sinkage) Models ............................ 36 2.5.2 Horizontal Shear Stress...

  18. Natural analogues of bitumen and bituminized radioactive waste

    International Nuclear Information System (INIS)

    Hellmuth, K.-H.

    1989-07-01

    Occurrences of natural bitumen provide possibilities to identify and assess materials, processes, phenomena and conditions in nature which can serve as model cases valid also with respect to a final repository. Natural bitumens meet the basic requirements for use as natural analogues. In natural sites, processes of bitumen formation and degradation often work simultaneously. The major processes are thermal alteration, evaporation, reaction with water, biodegradation, oxidation, weathering and radiation degradation. Progress in analytical organic geochemistry made during recent years has enabled a deeper understanding of the structural and compositional effects of these processes on bitumen. This is necessary in natural analogue applications. The time scales involved in degradation processes, as observed in natural occurrences, exceed the time scales dictated by the half-lives of most important fission products in low and medium level waste by orders of magnitude. Only exposure to the weather at the surface leads to a more rapid destruction of bitumen. Trace metals in bitumen arenot released until the matrix is completely destroyed. Products of radiation degradation and weathering of bitumen are able, to a certain degree, to delay migration of the metal ions released. Impregnation with bitumen may effectively reduce the microbial decomposition of easily destructable organic waste components, as can be deduced on the basis of the excellent preservation of fossils observed in bitumen. The complexity of all the natural sites described requires extensive understanding of the origin and kind of organic material in bitumen, its maturation, migration, alteration and degradation and of the geological and tectonic evolution of the site. The latter is used for establishing the time scale

  19. Provenance Study Of Bituminous Sands In Eastern Dahomey Basin ...

    African Journals Online (AJOL)

    The separation of these heavy minerals using bromoform (specific gravity 2.85) and slide examination under the petrographic microscope indicated the presence of zircon, rutile, staurolite, sillimanite, kyanite, garnet and epidote. Opaque minerals dominate the assemblage and they occur in significant quantities in some ...

  20. An evaluation of fracture toughness of bituminous coal

    International Nuclear Information System (INIS)

    Pathan, A.G.

    2005-01-01

    The role of fracture mechanics in the design of rock structures is vitally important. However, because of the complexities of rock structures and lack of understanding of the fundamentals of the failure mechanism, it has become customary to use the engineering properties approach in the design of stable rock structures. Recently considerable attention has been given and attempts are being made to apply the fracture mechanics approach to the design of safe mining structures. In mining engineering the fracture mechanics may be applied to calculate the formation of fracture zones around mine opening, thus estimating support requirements and formulating guide lines for the selection of mine roadway support system. The research work presented here is concerned with the evaluation of fracture toughness of coal under laboratory conditions. Diametral compression test method is used to determine the fracture toughness parameter of coal in the opening model failure. The effect of crack length and dimensionless crack length on the fracture toughness was studied also. A laboratory investigation of fracture toughness of coal in tensile mode failure has led to the conclusion that fracture toughness could be treated as a material property. (author)

  1. Characterization and Identification of Bituminous Materials Modified with Montmorillonite Nanoclay

    NARCIS (Netherlands)

    Liu, G.

    2011-01-01

    Montmorillonite (Mt) nanoclay is a layered silicate mineral with a 2:1-type layer structure, two tetrahedrals sandwiching one octahedral. In recent decades, it is successfully introduced into polymer systems to form polymer-clay nanocomposites (PCN) in which the silicate layers of the Mt are

  2. Full depth bituminous recycling of I-70, Thomas County, Kansas

    Science.gov (United States)

    2004-01-01

    In 1990, 13 full depth asphalt pavement test sections were built on a portion of I-70 in Thomas County, Kansas. Various combinations of hot mix and cold recycle mixes with different additives were used to build the test sections. Two of the test sect...

  3. Polyfunctional Modifiers for Bitumen and Bituminous Materials with High Performance

    Directory of Open Access Journals (Sweden)

    Alim Feizrakhmanovich Kemalov

    2018-01-01

    Full Text Available Over the last decade increase in capacity and the intensity of vehicular traffic has increased manifoldly, including heavy trucks, super singles, and higher tire pressures, resulting in significant increase of dynamic loads on the road surface which in turn lead to high quality requirements for bitumen in order to avoid premature wear and failure of asphalt concrete pavements. One of the possibilities to increase the quality of bitumen is to use special additives and modifiers that can provide a high adhesion to mineral filler and inhibit the aging and degradation processes in the asphalt coating. To achieve this, in the present study composite modifiers based on bisimidazolines derivatives were synthesized. The developed polyfunctional modifier (PFM of complex action provides enhanced thermal stability, significantly improves the adhesion between bitumen binder and aggregates, and also improves the physical-mechanical properties of the asphalt concrete. Based on the test results it is recommended to use the synthesized samples of the PFM additive with complex action in asphalt mixtures for road paving.

  4. 30 CFR 75.380 - Escapeways; bituminous and lignite mines.

    Science.gov (United States)

    2010-07-01

    ... coil at least eight inches in length. The spiraled coil must be placed within reach of the lifeline..., provided they are located on or near a working section and are moved as the section advances or retreats... located on or near a working section that are moved as the section advances or retreats; (E) Pumps...

  5. Bituminization process of radioactive liquid wastes by domestic bitumen

    International Nuclear Information System (INIS)

    Sang, H.L.

    1977-11-01

    A study has been carried out of the incorporation of intermediate level wastes in bitumen. Two kinds of wastes: a) an evaporator concentrate from a PWR (containing boric acid), b) second cycle wastes from the Purex process (containing sodium salts), were satisfactorily incorporated into a mixture of straight and blown domestic bitumen, to yield a product containing 50wt% solids. The products were stable to radiation exposure of 5'8x10 8 rads. Leach rates were measured in both distilled and sea water over periods up to 200 days at 5 0 C and 25 0 C and at both 1 atm and 8 atm pressure. Results confirmed that long term storage of the products would be satisfactory

  6. Use of expanded clay aggregate in bituminous construction.

    Science.gov (United States)

    1959-01-01

    In an effort to find a solution to the shortage of aggregate, for use in highway construction, Louisiana Department of Highways initiated a study. : In early 1955, we started experimenting with expanded aggregate or lightweight aggregate as commonly ...

  7. Use of emulsion for warm mix asphalt

    Directory of Open Access Journals (Sweden)

    Mahabir Panda

    2017-06-01

    Full Text Available Due to increase in energy costs and emission problems in hot mix asphalt usually used, it brought a great interest to the researchers to develop the warm mix technology for pavement constructions. Commonly known as warm mix asphalt (WMA, it is a typical method in the bituminous paving technology, which allows production and placement of bituminous mixes at lower temperatures than that used for hot mix asphalt (HMA. The WMA involves an environmental friendly production process that utilises organic additives, chemical additives and water based technologies. The organic and chemical additives are normally very costly and still involve certain amount of environmental issues. These factors motivated the authors to take up this technology using simple, environment friendly and somewhat cost effective procedure. In this study, an attempt has been made to prepare warm mixes by first pre-coating the aggregates with medium setting bitumen emulsion (MS and then mixing the semi-coated aggregates with VG 30 bitumen at a lower temperature than normally required. After a number of trials it was observed that mostly three mixing temperatures, namely temperatures 110 °C, 120 °C and 130 °C were appropriate to form the bituminous mixes with satisfactory homogeneity and consistency and as such were maintained throughout this study. Marshall samples for paving mixes were prepared using this procedure for dense bituminous macadam (DBM gradings as per the specifications of Ministry of Road Transport and Highways (MORTH and subsequently Marshall properties of the resultant mixes were studied with the main objective of deciding the different parameters that were considered for development of appropriate warm mix asphalt. In this study it has been observed that out of three mixing temperatures tried, the mixes prepared at 120 °C with bitumen-emulsion composition of 80B:20E for DBM warm mix, offer highest Marshall stability and highest indirect tensile strength

  8. Amenability of some Witbank bituminous ultra fine coals to binderless briquetting

    CSIR Research Space (South Africa)

    Mangena, SJ

    2004-10-15

    Full Text Available briquetting press, at various feed moisture contents. The formed briquettes were then tested for compressive strength and water resistance and the values correlated with the coal characteristics and the briquetting conditions. The coals were found...

  9. Development and evaluation of an automated reflectance microscope system for the petrographic characterization of bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Hoover, D. S.; Davis, A.

    1980-10-01

    The development of automated coal petrographic techniques will lessen the demands on skilled personnel to do routine work. This project is concerned with the development and successful testing of an instrument which will meet these needs. The fundamental differences in reflectance of the three primary maceral groups should enable their differentiation in an automated-reflectance frequency histogram (reflectogram). Consequently, reflected light photometry was chosen as the method for automating coal petrographic analysis. Three generations of an automated system (called Rapid Scan Versions I, II and III) were developed and evaluated for petrographic analysis. Their basic design was that of a reflected-light microscope photometer with an automatic stage, interfaced with a minicomputer. The hardware elements used in the Rapid Scan Version I limited the system's flexibility and presented problems with signal digitization and measurement precision. Rapid Scan Version II was designed to incorporate a new microscope photometer and computer system. A digital stepping stage was incorporated into the Rapid Scan Version III system. The precision of reflectance determination of this system was found to be +- 0.02 percent reflectance. The limiting factor in quantitative interpretation of Rapid Scan reflectograms is the resolution of reflectance populations of the individual maceral groups. Statistical testing indicated that reflectograms were highly reproducible, and a new computer program, PETAN, was written to interpret the curves for vitrinite reflectance parameters ad petrographic.

  10. Case study: dynamic modulus characterization of naturally occurring bituminous sands for sustainable pavement applications

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2010-11-01

    Full Text Available . The presence of high bitumen content makes oil sand materials problematic for field operations of off-road haul trucks and shovels during the warm spring and summer months. The behavior of oil sand materials is primarily dependent upon stress states...

  11. Alternative Fillers for the Production of Bituminous Mixtures: A Screening Investigation on Waste Powders

    Directory of Open Access Journals (Sweden)

    Cesare Sangiorgi

    2017-06-01

    Full Text Available There has been a significant increase in the demand for using recycled materials in construction because of the lack and limitation of available natural resources. A number of industrial and domestic waste products are being used in the replacement of traditional materials for road construction, and many studies have been carried out in recent years on the use of different recycled materials in substitution of conventional fillers in Asphalt Concretes (AC. The aim of this laboratory research is to analyze the physical characteristics of three different recycled fillers and compare them with those of a traditional limestone filler. The alternative fillers presented in this paper are: a waste bleaching clay that comes from two consecutive stages in the industrial process for decolouring vegetable oils and producing biogas (Ud filler, a dried mud waste from a tungsten mine (MW filler and a recycled glass powder (Gl filler. Results show significant differences between the fillers, and, in particular, Rigden Voids (RV seem to have the largest potential influence on the rheology of ACs.

  12. Utilization of polyethylene terephthalate (PET) in bituminous mixture for improved performance of roads

    Science.gov (United States)

    Ahmad, A. F.; Razali, A. R.; Razelan, I. S. M.; Jalil, S. S. A.; Noh, M. S. M.; Idris, A. A.

    2017-05-01

    Plastic bottle for recycling can be found from the household waste stream, and most of them are made from Polyethylene Terephthalate. In this research, PET is utilized to explore the potential prospects to upgrade asphalt mixture properties. The objectives include deciding the best measure of PET to be used. For experimental, Marshall mix design was utilized to determine the ideal bitumen binder content and to test the modified mixture properties. The samples were created per the requirement for aggregate course wearing (ACW14) using the Standard Specification of Road Work (SSRW) in Malaysia. 20 samples were utilized to determine the binder content, and 30 samples were used to research the impact of modifying asphalt mixtures. 2%, 5%, 10%, 15% and 20% of PET by weight of the optimum binder content (4.8%) were tested. Optimum PET content is 10%, and the result shows a good stability with 16.824kN, 2.32g/cm3 bulk density, void filled with bitumen (VFB) with 71.35%, flow with 3.2248mm, air void (AV) with 4.53%, and void of mineral aggregate (VMA) with 15.15%. The outcomes showed that PET modifier gives better engineering properties. Therefore, 10% of PET by the weight of binder content was suggested as the best amount of the modifier.

  13. XRD and FT–IR investigations of sub-bituminous Assam coals

    Indian Academy of Sciences (India)

    TECS

    ash content (5⋅70 %wt). The percentage of ash is of signi- ficance in the usefulness of coals. On the other hand, the highest ash containing Tipong coal has lower sulphur content with a value of 4⋅14 (%wt). The composition of ash varies with the rank of coal and in some cases, variations are observed in the same seam.

  14. Use of bottom ash from thermal power plant and lime as filler in bituminous mixtures

    Directory of Open Access Journals (Sweden)

    López-López, E.

    2015-06-01

    Full Text Available This study focuses on the characterization of bottom ash (PCC-BA and determining the mechanical characteristics of hot mix asphalt (HMA using PCC-BA and hydrated lime (HL as filler. Physical and chemical characterization of the bottom ash was carried out to evaluate its eventual reutilization as filler substitute. The materials tested in this study were made using 0%, 25%, 50%, 70% and 100% of PCC-BA combined with HL. HMA mixes were evaluated in terms of their engineering properties, namely: air voids in the mixes, water sensitivity, stiffness modulus, performance in wheel tracking test and fatigue resistance. The results obtained indicate that HMA mixes with a filler blend of 70% PCC-BA and 30% HL fulfil European standards and are suitable for light traffic or small infrastructures.Este estudio se centra en la caracterización de las cenizas de fondo (PCC-BA y la determinación de las características mecánicas de mezclas bituminosas en caliente (HMA, utilizando cenizas de fondo y la cal hidratada (HL como filler. Se realizó la caracterización física y química de las cenizas de fondo para evaluar su empleo como sustituto de filler. Las mezclas ensayadas en este estudio se realizaron utilizando 0%, 25%, 50%, 70% y 100% de cenizas de fondo combinadas con cal hidratada. Se evaluaron propiedades ingenieriles de las mezclas bituminosas, tales como los huecos de aire en las mezclas, la sensibilidad al agua, el módulo de rigidez, el ensayo de pista y la resistencia a la fatiga. Los resultados obtenidos indican que las mezclas bituminosas fabricadas con una combinación de filler del 70% de cenizas de fondo y el 30% cal hidratada, cumplen con las normas europeas y son adecuados para su aplicación con tráficos ligeros o en pequeñas infraestructuras.

  15. Current developments in performance testing of bituminous emulsions used in chip seals

    CSIR Research Space (South Africa)

    Johannes, PT

    2015-08-01

    Full Text Available literature review identifying common distresses occurring in chip seals, both during construction and in-service. Emulsion properties related to specific distresses as well as potential laboratory test methods for evaluating the identified emulsion properties...

  16. Modeling of bubble growth in complex fluids. Application to radiolytic swelling of nuclear bituminized waste products

    International Nuclear Information System (INIS)

    Marchal, Antoine

    2015-01-01

    The aim of this PhD thesis is to predict the swelling of bitumen barrels in which radioactive salts are mixed. The bitumen exposed to radioactivity undergoes a chemical reaction: the radiolysis. This implies a generation of dihydrogen. The created is solubilized until the concentration reaches a limit value which is called saturation. Over this limit nucleation of bubbles is observed. Then they will grow thank to the contribution of the gas generated by radiolysis and they will be submitted to Archimede's principle so that they will rise in the fluid. The swelling is the result of the competition between generation and evacuation of gas. A model has been built to describe the evolution of a bubble population. Because of it is not possible to solve it analytically, a numerical program was developed. The results show that an increase of the fluid viscosity, the gas generation or the container height lead to an increase of the swelling and that an increase of the diffusion coefficient contributes to a decrease of the swelling. In the particular case of a yield stress fluid, the behavior of the bubble population is modified and the evacuation of gas is done with several shots, at the opposite of the case of a Newtonian fluid for which a stationary evacuation is reached. (author)

  17. Characterization of granite and limestone powders for use as fillers in bituminous mastics dosage

    Directory of Open Access Journals (Sweden)

    BRENO BARRA

    2014-06-01

    Full Text Available This paper discusses the importance of studies on materials known as fillers from different mineral origins, used in asphalt mixes, specifically in the formulation of mastics. The research was carried out on samples of limestone and granite rock filler and asphalt binder (50/70. The samples were evaluated through semiquantitative chemical analyses by X-ray fluorescence, granulometry by low angle laser emission, scanning electron microscopy, softening point tests, penetration tests, and aggregate-asphalt binder and aggregate-mastic adhesion tests. The results highlighted convergent trends, indicating that the active behavior of the fillers in the mastic formulation is not related to the size of the particles, but rather to their form, surface texture, specific surface area and mineralogical nature, allowing the filler activity concept to be divided into two components: physical (hardening and chemical (adhesion.

  18. Creep recovery behaviour of bituminous binders - relevance to permanent deformation of asphalt pavements

    CSIR Research Space (South Africa)

    Mturi, GAJ

    2012-05-01

    Full Text Available to differentiate the resistance to permanent deformation of different road binders. The MSCR test is essentially a repeated creep-recovery test at a fixed loading/unloading interval. This paper aims to highlight the limitations of the MSCR test but also show how...

  19. Evolution of rheological properties of nuclear bituminized waste products, towards an ageing/viscosity law

    International Nuclear Information System (INIS)

    Mouazen, M.

    2011-01-01

    This work is a contribution to the understanding of rheological properties of bitumen and their evolution under gamma irradiation. The prediction of swelling ratio is necessary to evaluate the state of the containers, particularly during the reversibility phase of the storage. The objective of this work is thus to establish the rheological data its evolution under irradiation in order to predict the container swelling with time. After the rheological and thermal characterization of pure bitumen, a series of extrusion trials has been carried out. The state of dispersion essentially depends on the ratio N/Q (screw speed to feed rate). Extreme values of N/Q show the highest yield stress, indicating an improved dispersion state. The industrial bitumen compound exhibits the highest viscosity compared to model compounds, which limits bubble migration. Finally, the effect of gamma irradiation on pure bitumen and compounds behaviour has been studied. External and structural modifications have been evidenced. A theoretical model based on Krieger-Dougherty equation has been developed and shows a good agreement with experimental data. (author)

  20. Production costs of auto gasoline and DHD feed from bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    1942-11-04

    This report consists of three tables. The first table shows data concerning the 700 atm liquid phase and a production capacity of 146,000 tons/yr of gasoline and middle oil. The cost is shown in Reichsmarks per ton of gasoline and middle oil for individual areas such as: 1.73 tons of hydrogenation coal, with 10% water and 4% ash as being 40 RM, 1900 m/sup 3/ H/sub 2/ being 83.50 RM, catalysts and chemicals being 2.40 RM, power being 32.0 RM, and wages, materials, operating materials and laboratory costs as being 19.6 RM. The total of all areas listed was 211.60 RM/ton of gasoline and middle oil. The second table is for the 300 atm vapor phase showing RM/ton of auto gasoline and RM/ton 170/sup 0/-endpoint gasoline based on the gasoline being free of C/sub 4/. This is given for liquid phase gasoline and middle oil, hydrogen, liquid petroleum gasoline credit, hydrogenation gas credit, catalyst and chemicals, power, wages, repairs, fire protection and taxes, amortization, general, 3% interest, and 5% interest. The same information given in the second chart is also given in the third chart except it was for a 700 atm vapor phase operation. The 300 atm-process seemed to have slightly higher cost than the 700 atm process, partly because of using more hydrogen and more expensive catalyst. 3 tables

  1. Rheological behaviour of polymer-modified bituminous mastics : a comparative analysis between physical and chemical modification

    OpenAIRE

    Shivokhin, Maxim; García Morales, Moisés; Partal López, Pedro; Cuadri Vega, Antonio Abad; Gallegos Montes, Críspulo

    2012-01-01

    Mastic, a bitumen/filler blend which naturally forms when bitumen is mixed with aggregates is the actual product used to bind coarse mineral particles in the asphalt mixtures. As a result, the characterisation of mastics is essential to improve the understanding of the response and performance of asphalt concrete pavements. On the other hand, the lack of experimental data concerning the behaviour of mastics and, above all, polymer-modified mastics has been lately claimed. In that sense, this ...

  2. Hydrogen production by two-stage co-pyrolysis of bituminous coal-polymers mixtures

    Czech Academy of Sciences Publication Activity Database

    Straka, Pavel; Kříž, Vlastimil

    2008-01-01

    Roč. 5, č. 1 (2008), s. 77-82 ISSN 1214-9705 R&D Projects: GA ČR(CZ) GA105/07/1407 Institutional research plan: CEZ:AV0Z30460519 Keywords : co-pyrolysis * coal * polymers Subject RIV: CD - Macromolecular Chemistry

  3. Aggregate strength for bituminous surfacings for low volume roads: a heavy vehicle simulator experience

    CSIR Research Space (South Africa)

    Paige-Green, P

    2004-09-01

    Full Text Available This paper discusses an investigation using the CSIR Transportek Heavy Vehicle Simulator (HVS) to determine the impact of using aggregates softer than specified in chip seals and to propose possible relaxations in the currently specified strength...

  4. Eastern gas shales bibliography selected annotations: gas, oil, uranium, etc. Citations in bituminous shales worldwide

    Energy Technology Data Exchange (ETDEWEB)

    Hall, V.S. (comp.)

    1980-06-01

    This bibliography contains 2702 citations, most of which are annotated. They are arranged by author in numerical order with a geographical index following the listing. The work is international in scope and covers the early geological literature, continuing through 1979 with a few 1980 citations in Addendum II. Addendum I contains a listing of the reports, well logs and symposiums of the Unconventional Gas Recovery Program (UGR) through August 1979. There is an author-subject index for these publications following the listing. The second part of Addendum I is a listing of the UGR maps which also has a subject-author index following the map listing. Addendum II includes several important new titles on the Devonian shale as well as a few older citations which were not found until after the bibliography had been numbered and essentially completed. A geographic index for these citations follows this listing.

  5. Temperature induced healing in strained bituminous materials observed by atomic force microscopy

    NARCIS (Netherlands)

    Nahar, S.N.; Schmets, A.J.M.; Scarpas, A.; Schitter, G.

    2013-01-01

    Bitumen is the binder in the composite material named asphalt concrete. Under cyclic mechanical loading of traffic passing over the pavement, eventually damage will initiate in the pavement, leading to eventual structural failure. This damaging process is accelerated by time dependent change of the

  6. Evaluation of the fatigue macro-cracking behavior of crumb rubber modified bituminous mixes

    Directory of Open Access Journals (Sweden)

    Moreno-Navarro, F.

    2014-09-01

    Full Text Available The use of crumb rubber modified bitumen (CRMB in asphalt mixes is a road engineering technology that has become increasingly important in recent years. Given the many economic and environmental benefits of this type of binder, the goal is to give CRMB the same level of performance as conventional polymer-modified bitumen. The appearance and propagation of cracks due to fatigue phenomena is one of the most common distresses affecting road pavements. Since crumb rubber enhances the mechanical properties of asphalt mixes, it can provide a viable solution for fatigue cracking. This paper presents the results of a comparative analysis of the fatigue-cracking behavior of asphalt mixtures manufactured with crumb rubber modified bitumen and polymer-modified bitumen.El empleo de betunes modificados con polvo de neumático usado en la fabricación de mezclas bituminosas es una de las técnicas que mayor auge está teniendo en los últimos años en la ingeniería de carreteras. Dadas sus grandes ventajas económicas y ambientales, este tipo de ligantes pretende conseguir prestaciones similares a la de los betunes modificados con polímeros utilizados habitualmente. La aparición de fisuras debido a fenómenos de fatiga es una de las patologías más comunes en firmes de carretera. Debido a las mejoras de las propiedades mecánicas del betún aportadas tras la incorporación de polvo de neumático, las mezclas fabricadas con estos ligantes se postulan como una posible solución a dicho problema. En este artículo se lleva a cabo un análisis comparativo del comportamiento a fisuración por fatiga realizado sobre mezclas bituminosas fabricadas con betún modificado con polvo de neumático y con polímeros.

  7. Interfacial interactions and mass transfer at the interfacial region of bituminous hydrocarbon mixtures

    NARCIS (Netherlands)

    Van Lent, D.Q.

    2014-01-01

    The adhesion between bitumen and aggregate is a complex process with numerous of variables. To improve the understanding of the bond between bitumen and aggregates in road applications, this research focuses on preferential adsorption, which is one aspect of bitumen-aggregate adhesion. The main

  8. The analysis and use of black steel slag in bituminous mixtures

    OpenAIRE

    Korbar, Primož

    2013-01-01

    In my diploma thesis I dealt with the use of black steel slag in road construction. In the introductory part of my work I discussed the general characteristics of the materials used in road construction and later on in the paper I focused exclusively on black steel slag. I described the history of the use of slag in the construction industry, various types of iron and steel slags, and the processing of black and white steel slag. I was interested in positive and negative characteristics of sl...

  9. Recommended procedures and techniques for the petrographic description of bituminous coals

    Science.gov (United States)

    Chao, E.C.T.; Minkin, J.A.; Thompson, C.L.

    1982-01-01

    Modern coal petrology requires rapid and precise description of great numbers of coal core or bench samples in order to acquire the information required to understand and predict vertical and lateral variation of coal quality for correlation with coal-bed thickness, depositional environment, suitability for technological uses, etc. Procedures for coal description vary in accordance with the objectives of the description. To achieve our aim of acquiring the maximum amount of quantitative information within the shortest period of time, we have adopted a combined megascopic-microscopic procedure. Megascopic analysis is used to identify the distinctive lithologies present, and microscopic analysis is required only to describe representative examples of the mixed lithologies observed. This procedure greatly decreases the number of microscopic analyses needed for adequate description of a sample. For quantitative megascopic description of coal microlithotypes, microlithotype assemblages, and lithotypes, we use (V) for vitrite or vitrain, (E) for liptite, (I) for inertite or fusain, (M) for mineral layers or lenses other than iron sulfide, (S) for iron sulfide, and (X1), (X2), etc. for mixed lithologies. Microscopic description is expressed in terms of V representing the vitrinite maceral group, E the exinite group, I the inertinite group, and M mineral components. volume percentages are expressed as subscripts. Thus (V)20(V80E10I5M5)80 indicates a lithotype or assemblage of microlithotypes consisting of 20 vol. % vitrite and 80% of a mixed lithology having a modal maceral composition V80E10I5M5. This bulk composition can alternatively be recalculated and described as V84E8I4M4. To generate these quantitative data rapidly and accurately, we utilize an automated image analysis system (AIAS). Plots of VEIM data on easily constructed ternary diagrams provide readily comprehended illustrations of the range of modal composition of the lithologic units making up a given coal bed. The use of bulk-specific-gravity determinations is alo recommended for identification and characterization of the distinctive lithologic units. The availability of an AIAS also enhances the capability to acquire textural information. Ranges of size of maceral and mineral grains can be quickly and precisely determined by use of an AIAS. We assume that shape characteristics of coal particles can also be readily evaluated by automated image analysis, although this evaluation has not yet been attempted in our laboratory. Definitive data on the particulate mineral content of coal constitute another important segment of petrographic description. Characterization of mineral content may be accomplished by optical identification, electron microprobe analysis, X-ray diffraction, and scanning and transmission electron microscopy. Individual mineral grains in place in polished blocks or polished this sections, or separated from the coal matrix by sink-float methods are studied by analytical techniques appropriate to the conditions of sampling. Finally, whenever possible, identification of the probable genus or plant species from which a given coal component is derived will add valuable information and meaning to the petrographic description. ?? 1982.

  10. ANALYSIS OF COAL TAR COMPOSITIONS PRODUCED FROM SUB-BITUMINOUS KALIMANTAN COAL TAR

    OpenAIRE

    Dewi Selvia Fardhyanti; Astrilia Damayanti

    2016-01-01

    Coal tar is a liquid by-product of coal pyrolysis processes. This liquid oil mixture contains various kinds of useful compounds such as benzoic aromatic compounds and phenolic compounds. These compounds are widely used as raw material for insecticides, dyes, medicines, perfumes, coloring matters, and many others. The coal tar was collected by pyrolysis process of coal obtained from PT Kaltim Prima Coal and Arutmin-Kalimantan. The experiments typically occurred at the atmo...

  11. ANALYSIS OF COAL TAR COMPOSITIONS PRODUCED FROM SUB-BITUMINOUS KALIMANTAN COAL TAR

    Directory of Open Access Journals (Sweden)

    Dewi Selvia Fardhyanti

    2016-10-01

    Full Text Available Coal tar is a liquid by-product of coal pyrolysis processes. This liquid oil mixture contains various kind of useful compounds such as benzoic aromatic compounds and phenolic compounds. These compounds are widely used as raw material for insecticides, dyes, medicines, perfumes, coloring matters, and many others. The coal tar was collected by pyrolysis process of coal obtained from PT Kaltim Prima Coal and Arutmin-Kalimantan. The experiments typically occurred at the atmospheric pressure in a laboratory furnace at temperatures ranging from 300 to 550oC with a heating rate of 10oC/min and a holding time of 1 hour at the pyrolysis temperature. The Gas Chromatography-Mass Spectroscopy (GCMS was used to analyze the coal tar components. The obtained coal tar has the viscosity of 3.12 cp, the density of 2.78 g/cm3, the calorific value of 11,048.44 cal/g, and the molecular weight of 222.67. The analysis result showed that the coal tar contained more than 78 chemical compounds such as benzene, cresol, phenol, xylene, naphtalene, etc. The total phenolic compounds contained in coal tar is 33.25% (PT KPC and 17.58% (Arutmin-Kalimantan. The total naphtalene compounds contained in coal tar is 14.15% (PT KPC and 17.13% (ArutminKalimantan.

  12. Data for comparing hydrogenation with low temperature carbonization (L. T. C. ) of bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Fahr

    1943-05-24

    A chart is presented with three main headings for processes applied to coal with 7,000 heat units/kg and 8% H/sub 2/O: (A) Lurgi Spuelgas (rinsing gas) Carbonization for Upper Silesia, and (B) Brennstoff-Technik (B.T.) Carbonization for Upper Silesia, and (C) Coke Plant for Upper Silesia. The following were given for each heading: coke yield at 7,000 heat units and 5% H/sub 2/O; tar yield; LTC gas; heat requirements for the kiln drum; production involving coal for weak gas; power requirements; steam requirements; coal for current and steam; and tar processing. Coke with 0% H/sub 2/O based on a dry coal basis showed yields of 72.5% for (A), 75.0% for (B), and 71.0% for (C). Coke with 5% H/sub 2/O based on anhydrated dry coal showed 70.2% for (A), 72.5% for (B), and 68.7% for (C). Particle sizes that were 20 mm in size or larger constituted 82.3% of (A), 71.6% of (B), and 85.0% of (C). Volatile constituents were given as 7.0% for (A), 9.0% for (B), and 7.0% for (C). Tar yield based on dry coal was 9.2% for (A), 8.5% for (B), and 4.0% for (C). Tar yield based on anhydrated dry coal was 10.1% for (A), 9.8% for (B), and 5.0% for (C). Power requirements in KW hr/hr for 1 million tons dry coal were 2,100 for (A), 3,100 for (B), and 2,000 for (C). Coal for current and steam for 1 million tons anhydrated dry coal were 12,900 tons/yr for (A), 12,000 tons/yr for (B), and 20,000 tons/yr for (C). 1 table

  13. Characterizing resilient behavior of naturally occurring bituminous sands for road construction

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2010-11-01

    Full Text Available large capacity haul trucks and shovels. This paper focuses on determining in laboratory the resilient behavior of three oil sand materials with bitumen contents of 8.5, 13.3, and 14.5% by weight. The resilient modulus MR properties were obtained using a...

  14. Chemical characteristics of organic aerosol in Bab-Ezzouar (Algiers). Contribution of bituminous product manufacture.

    Science.gov (United States)

    Yassaa, N; Meklati, B Y; Cecinato, A; Marino, F

    2001-10-01

    The organic compositions of atmospheric particulate matter from Bab-Ezzouar (Algiers) have been investigated to assess the air pollution levels suspected to be caused by asphalt product and yeast manufactures. After a medium-volume air sampling, soxhlet extraction, alumina elution and HPLC separation, the extracts were analysed by high-resolution gas chromatography (HRGC) and gas chromatography coupled to mass spectrometry (GC-MS). The composition of n-alkane and polycyclic aromatic hydrocarbons (PAH) fractions reflected the petrogenic origin from the emission of asphalt materials production in addition to vascular plant wax emissions. In contrast, microbial activities seemed to play the main role for the presence of n-alkanoic acids at Bab-Ezzouar. The sole nitrated polycyclic aromatic hydrocarbons (NPAH) observed, i.e., 2-nitrofluoranthene (2NFA), was very likely to arise from gas-phase photochemical reaction of parent PAH in the atmosphere. The total aerial levels ranged from 75 to 206 ng m(-3) for n-alkanes, from 153 to 345 ng m(-3) for n-alkanoic acids and from 44 to 100 ng m(-3) for PAH and NPAH. Although the samples were collected during the hot season, the levels of these pollutants seemed to be important and of environmental concern, especially for PAH species.

  15. Acid mine drainage abatement resulting from pressure grouting of buried bituminous mine spoils

    International Nuclear Information System (INIS)

    Scheetz, B.; Silsbee, M.; Schueck, J.

    1998-01-01

    A 37 acre surface coal mine located in Clinton County, PA, USA, was mined and reclaimed between 1974 and 1977. Buried pyrite-rich pit floor cleanings and tipple refuse were found to be producing severe acid mine drainage. The pyritic material is located in discrete piles or pods in the backfill. The pods and the resulting contaminant plumes were initially defined using geophysical techniques and confirmed by drilling. The approach taken was to use a cementitious grout, composed of fluidized bed combustion ash and water, which would be placed in a manner which would prevent water and oxygen from contacting the pyritic materials. Statistically significant water quality improvements have been noted as a result of the grouting. After four years of post-grouting monitoring, reductions in concentrations of most of the mine drainage parameters range from 40 to 90%. 12 refs., 1 fig., 4 tabs

  16. Solar Radiation effect on the bituminous binder; Efecto de la radiacion solar sobre el ligante bituminoso

    Energy Technology Data Exchange (ETDEWEB)

    Tadeo Rico, A.; Torres Perez, A.

    2010-07-01

    Asphalt, used as binder in road construction, becomes more brittle and harder during working life on the surface of the road pavement, conducting toward their deterioration. This is caused by the oxidation of the molecular functional groups of the asphalt molecular structure. Moreover, it is observed that ultraviolet radiation increases the oxidation process. However, the effect of solar light on the asphalt degradation has been poorly researched. The aim of this work is to study asphalt ageing caused by effect of solar radiation, by using standard test. Four commercial asphalts from different companies were selected: two with penetration number 50/70, and the other two polymer modified asphalts. From each of the asphalts forty samples were taken off and placed in four different aging conditions of temperature and radiation for a period ranging from 40 to 500 days. Ring and Ball test, and Fraass breaking Point test, were used to analyse the changes of asphalt properties after exposition to solar radiation. The results of the four analyzed asphalts showed a distinct behaviour; not only in the test temperature increase but also in the rate. Another experiment was carried out. Samples from a hot mix asphalt batch were placed under solar radiation, and were compacted by the Marshall procedure after increasing periods of time. Density and resistance to plastic flow using Marshall Apparatus were measured. Results showed an increase in the stability of samples under radiation. Both experiments show that the solar radiation is enough to cause changes in the asphalt molecular structure due to oxidation. So that, the study of the effect of the solar radiation on the asphalt properties could be a good tool to asses the performances of asphalt pavement. (Author) 26 refs.

  17. Hydrogen from the two-stage pyrolysis of bituminous coal/waste plastics mixtures

    Czech Academy of Sciences Publication Activity Database

    Kříž, Vlastimil; Bičáková, Olga

    2011-01-01

    Roč. 36, č. 15 (2011), s. 9014-9022 ISSN 0360-3199 R&D Projects: GA ČR(CZ) GA105/07/1407 Institutional research plan: CEZ:AV0Z30460519 Keywords : hydrogen * two-stage pyrolysis * coal Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 4.054, year: 2011 http://www.sciencedirect.com/science/article/pii/S0360319911007622

  18. XRD and FT–IR investigations of sub-bituminous Assam coals

    Indian Academy of Sciences (India)

    TECS

    extremely difficult and therefore, research on coal structure is still a challenging task and continues to be pursued intensively. The investigation of the chemical structure of coal has led to comprehensive and well-defined results on the basis of development of spectroscopic methods. These are FTIR, UV-visible spectroscopy, ...

  19. Modification of a force plate system for equine gait analysis on hard road surfaces: a technical note.

    Science.gov (United States)

    Wilson, A M; Pardoe, C H

    2001-04-01

    Studies on horseshoe materials have been limited to the analysis of kinematic data to determine slip times and distances, since equine force plate analysis is traditionally undertaken on a rubber-surfaced force plate. The purpose of this study was to modify a force plate for measuring ground reaction forces on a road surface and report preliminary data from the system. A steel-reinforced concrete top plate of 18 mm thickness and mass 23 kg, and a 12 mm thick top plate of 6 mm bituminous macadam wear coat (road surface) contained in a tray constructed of 2 mm thick steel, mass 21 kg, were constructed. The top plates were bolted to a forceplate and resonance frequency of the force plate top plate combinations were 278 Hz (concrete) and 218 Hz (roadway), respectively. Simultaneous kinetic and kinematic data were collected while a horse, shod in steel horseshoes, was trotted over the concrete-topped force plate until 8 foot placements were recorded. The foot slipped for mean +/- s.d. 35 +/- 7 mm in 29 +/- 8 ms after impact and both Fy and Fz increased during foot slip. The ratio of Fy/Fz during slip was relatively constant at 0.56 +/- 0.05. The top plates have proved resilient in use and have withstood a variety of horseshoe designs and tungsten-capped stud nails with minimal damage. They enable measurement of ground reaction forces on hard surfaces and the calculation of the energy dissipated via foot slippage by integration of the craniocaudal force-foot position data after impact.

  20. Geodynamic methods for assessing methane distribution in bituminous coal deposits and measures to intensify methane fluxes during mine gas drainage

    Directory of Open Access Journals (Sweden)

    Е. В. Гончаров

    2016-12-01

    Full Text Available This paper explores states of methane within the coal bearing stratum and shows heavy dependency of the intrastratal gas migration on the forms of porous space and petrographic properties of coal. The adsorbed methane is found to be predominant in the coal of Kuznetsk Basin. Different forms of coal diffusion and filtration are described revealing their dependency on geological and thermodynamic conditions. The paper provides justification for the primary focus on geodynamic processes when designing gas drainage systems and applicability of morphometric methods and remote sensing data for their identification. The significance of researches into the processes activating exothermic reactions resulting in methane transition to free state is explained. The paper presents the results of using seismic-acoustic stimulation techniques as one of the practical approaches to addressing this issue. Results of successful industrial testing have been compared with the results of numerical modelling of stress-strain state, which can also be managed through seismic-acoustic stimulation.

  1. Research on Reasonable Particle Size of Coal Blends for Blast Furnace Injection: Semi Coke and Bituminous Coal

    Science.gov (United States)

    Wang, Haiyang; Xu, Runsheng; Song, Tengfei; Zhang, Pengcheng

    Semi coke, a byproduct in the chemical industry, is a new fuel for blast furnace injection in China. In this study, semi coke and bitumite were milled into different size, ranged from 0.147mm to under 0.074mm. The content of volatile matter and ash, which affect the combustibility of semi coke, were measured using muffle furnace. The mixture, in which the proportion of coal in different sizes changed, was blend by semi coke and bitumite with different size. Activation energy calculation and the comprehensive combustion characteristic index of all kinds of blends was also discussed. The result obtained by Thermogravimetry -Derivative Thermogravimetry curves indicates that the smaller the size of mixture is, the lower for the characteristic temperature, and the better for its combustibility, Semi coke can be a substitute for anthracite in blast furnace injection.

  2. Waste tire and shingle scrap/bituminous paving test sections on the Munger Recreational Trail Gateway segment. interim report

    Science.gov (United States)

    1991-02-01

    The need to reduce Minnesota's dependence on land fills resulted in a unique cooperative venture by three state agencies. A partnership was forged between the Minnesota Pollution Control Agency (MPCA), the Minnesota Department of Natural Resources (D...

  3. Study on the structure and gasification characteristics of selected South African bituminous coal in fluidised bed gasification

    CSIR Research Space (South Africa)

    Oboirien, BO

    2009-10-01

    Full Text Available . The microstructural characteristics of the parent coals and their resultant chars were determined using XRD, FTIR, Raman and petrographic analysis. The microstructural changes that occurred in the organic (maceral) and the inorganic (mineral) fractions of the selected...

  4. Study on the conditions of bituminization of radioactive wastes and their influence on the stability of stored products

    International Nuclear Information System (INIS)

    Golinski, M.; Ksiazak, Z.

    1975-05-01

    Investigations carried out on a laboratory and semi-industrial scale showed that the Polish oxidised industrial bitumen P-60 was suitable for the solidification of liquid radioactive waste and particularly for non-concentrated post-precipitation sludges. The bitumen products were highly stable and were resistant to leaching by acids, salt solutions and water. Laboratory leach tests gave values similar to those obtained by others using different bitumen. By evaluating the sorption characteristics of the soil and the hydrogeological conditions existing at a proposed storage site, it was shown that the solidified wastes could be stored directly in the soil without further isolation from the soil water. Based on the liquid wastes arising from a nuclear power plant it has been shown that solidification of the wastes in bitumen will be cheaper than solidification of the same wastes using cement

  5. Comprehensive geobiological characterization of a bituminous carbonate facies with Ediacara-type fossils (Shibantan Member, South China)

    Science.gov (United States)

    Duda, Jan-Peter; Blumenberg, Martin; Thiel, Volker; Simon, Klaus; Zhu, Maoyan; Reitner, Joachim

    2015-04-01

    The Shibantan Member (Dengying Formation, Ediacaran Period) is one of only few carbonate settings with Ediacara-type fossils worldwide (e.g. Ding & Chen, 1981; Sun, 1986; Xiao et al., 2005; Shen et al., 2009; Chen et al., 2014). However, only little is known about the sedimentology and biogeochemistry of the environments in which these organisms throve. Here we provide a comprehensive geobiological characterization of the Shibantan Member, addressing the interplay between sedimentary and (bio-) geochemical processes. Sedimentary analysis revealed that black laminated limestones of the lower Shibantan Member were deposited after a sudden local deepening in a subtidal lower- to middle ramp environment close to the storm wave base, while the dark wavy dolomites of the upper Shibantan Member were deposited in a subtidal middle ramp environment between storm- and fair weather wave base. Sedimentation in the Shibantan basin was generally highly dynamic as evidenced by a distinct slumping horizon and mass-flow deposits that were possibly due to synsedimentary tectonic processes. The microbial-mat associated biota including Ediacara-type fossils is restricted to the lower Shibantan Member. Sedimentary analysis of this part reveals a close relationship between autochthonous mat growth and allochthonous and/or para-autochthonous event deposition. During deposition of the lower Shibantan Member the water column was probably temporarily stratified, with a sub- to anoxic water layer (evidenced by Ni/Co-, V/(V+Ni) and V/Sc ratios) overlain by a oxygenated upper layer (evidenced by negative Ce anomalies and low V/Cr ratios). However, such stratification was not permanent, as mixing by storm events is evidenced by hummocky cross stratification structures. 13C-enrichments in carbonates of the Lower Shibantan Member (δ13C = +3.3 to +4.0o VPDB) together with 13C-depletions of syngenetic n-alkanes cleaved from the respective extraction residue using catalytic hydropyrolysis (HyPy; δ13C = -31.7 to -36.3o VPDB) indicate a significant withdrawal of 12C by primary producers that thrived within the microbial mats. At the same time, sulphurised biomarkers in the bitumen and HyPy-treated extraction residue hint at organic matter decomposition and concomitant sulphide production by sulphate-reducing bacteria. Given the sedimentological evidence for periodical ventilation of the water column by storms, sulphide oxidising bacteria were possibly favoured whenever oxygen became available at the sediment-water interface. Taken together, the environments in which the microbial-mat-associated biota including Ediacara-type fossils throve were highly dynamic due to a complex interplay of geological and biological processes. References Chen Z., Zhou C., Xiao S., Wang W., Guan C., Hua H., Yuan X., 2014. New Ediacara fossils preserved in marine limestone and their ecological implications. Scientific Reports, 4 Ding Q. and Chen Y., 1981. Discovery of soft metazoan from the Sinian System along eastern Yangtze Gorge, Hubei. Journal of the Wuhan College of Geology, 2, 53-57. Shen, B., Xiao S., Zhou C., Yuan X., 2009. Yangtziramulus zhangi New Genus and Species, a Carbonate-Hosted Macrofossil from the Ediacaran Dengying Formation in the Yangtze Gorges Area, South China. Journal of Paleontology, 83(4): 575-587. Sun W., 1986. Late precambrian pennatulids (sea pens) from the eastern Yangtze Gorge, China: Paracharnia gen. nov. Precambrian Research, 31(4), 361-375. Xiao S., Shen B., Zhou C., Xie G., Yuan X., 2005. A uniquely preserved Ediacaran fossil with direct evidence for a quilted bodyplan. Proceedings of the National Academy of Sciences of the United States of America, 102(29), 10227-10232.

  6. An adsorption diffusion model for removal of para-chlorophenol by activated carbon derived from bituminous coal.

    Science.gov (United States)

    Sze, M F F; McKay, G

    2010-05-01

    Batch adsorption experiments were carried out to study the adsorptive removal and diffusion mechanism of para-chlorophenol (p-CP) onto Calgon Filtrasorb 400 (F400) activated carbon. The external mass transfer resistance is negligible in the adsorption process carried out under different conditions in batch operation. Intraparticle diffusion model plots were used to correlate the batch p-CP adsorption data; three distinct linear sections were obtained for every batch operation. The textural properties of F400 activated carbon showed that it has a large portion of supermicropores, which is comparable to the size of the p-CP molecules. Due to the stronger interactions between p-CP molecules and F400 micropores, p-CP molecules predominantly diffused and occupied active sites in micropore region by hopping mechanism, and eventually followed by a slow filling of mesopores and micropores. This hypothesis is proven by the excellent agreement of the intraparticle diffusion model plots and the textural properties of F400 activated carbon. Copyright 2009 Elsevier Ltd. All rights reserved.

  7. Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

    OpenAIRE

    Cieślik Ewelina; Konieczny Tomasz; Bobik Bartłomiej

    2018-01-01

    One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures ...

  8. Valuation of investments in natural resources using contingent-claim framework with application to bituminous coal developments in Korea

    International Nuclear Information System (INIS)

    Won, Chaehwan

    2009-01-01

    As Brennan and Schwartz [Brennan M, Schwartz E. Evaluating natural resource investment. Journal of Business 1985;58:135-57] point out in their pioneering work, the valuation of natural resources projects is particularly difficult due to the high degree of uncertainty in output prices of resources. In general, there are two competing procedures to evaluate risky projects in natural resources developments. One is decision analytic, based on traditional discounted cash flow and stochastic dynamic programming [Fleten SE, Maribu KM, Wangensteen I. Optimal investment strategies in decentralized renewable power generation under uncertainty. Energy 2007;32:803-15; Smith J, McCardle K. Valuing oil properties: integrating option pricing and decision analysis approaches. Operations Research 1998;46(2):198-217; Szklo AS, Carneiro JTG, Machado G. Break-even price for upstream activities in Brazil: evaluation of the opportunity cost of oil production delay in a non-mature sedimentary production region. Energy 2008;33:589-600], and the other is contingent claims analysis, based on the no-arbitrage theory of financial markets [Brennan M, Schwartz E. Evaluating natural resource investment. Journal of Business 1985;58:135-57; Emhjellen M, Alaouze CM. A comparison of discounted cash flow and modern asset pricing methods - project selection and policy implications. Energy Policy 2003;31:1213-20; Laughton D. The management of flexibility in the upstream petroleum industry. The Energy Journal 1998;19:83-114; Paddock L, Siegel D, Smith J. Option valuation of claims on real assets: the case of offshore petroleum leases. Quarterly Journal of Economics 1988;103(3):479-508; Schwartz ES. Valuing long-term commodity assets. Journal of Energy Finance and Development 1998;3(2):85-99; Sezgen O, Goldman CA, Krishnarao P. Option value of electricity demand response. Energy 2007;32:108-19]. In this paper, we use the second approach to develop a new model, and the main contributions are providing a tractable and realistic means of incorporating the option value and optimal timing into the investment decision in natural resources and presenting an example that shows option and timing considerations to be important. We demonstrated the validity of the model using both numerical analysis and real data.

  9. Study on the structure and gasification characteristics of selected South African bituminous coals in fluidised bed gasification

    CSIR Research Space (South Africa)

    Oboirien, BO

    2011-04-01

    Full Text Available . The microstructural characteristics of the parent coals and their resultant chars were determined using XRD, FT-IR, Raman and petrographic analysis. The microstructural changes that occurred in the organic (maceral) and the inorganic (mineral) fractions...

  10. Down-scaling of bituminous coal mining, restructuring of steel works and heavy engineering in the Ostrava region

    Czech Academy of Sciences Publication Activity Database

    Klusáček, Petr

    2005-01-01

    Roč. 13, č. 2 (2005), s. 3-12 ISSN 1210-8812 R&D Projects: GA AV ČR(CZ) IBS3086005 Institutional research plan: CEZ:AV0Z30860518 Keywords : Ostrava region * restructuring * steemaking and heavy industry * downscaling of coal- mining Subject RIV: DE - Earth Magnetism, Geodesy, Geography

  11. The Metric of Colour Space

    DEFF Research Database (Denmark)

    Gravesen, Jens

    2015-01-01

    The space of colours is a fascinating space. It is a real vector space, but no matter what inner product you put on the space the resulting Euclidean distance does not correspond to human perception of difference between colours. In 1942 MacAdam performed the first experiments on colour matching...... and found the MacAdam ellipses which are often interpreted as defining the metric tensor at their centres. An important question is whether it is possible to define colour coordinates such that the Euclidean distance in these coordinates correspond to human perception. Using cubic splines to represent...

  12. AUTOMATED CONTROL SYSTEM AND MONITORING BY TECHNOLOGICAL PROCESSES BY PRODUCTION OF POLYMERIC AND BITUMINOUS TAPES ON THE BASIS OF APPLICATION OF SCADA OF SYSTEM

    Directory of Open Access Journals (Sweden)

    A. S. Kirienko

    2016-01-01

    Full Text Available Expediency of use of a control system and monitoring of technological processes of production is proved in article that will allow to lower work expenses, and also to increase productivity due to the best production process.The main objective of system, remote monitoring is that gives the chance far off and to quickly give an assessment to the current situation on production, to accept reasonable and timely administrative decisions.

  13. Laboratory and field evaluations of non-bituminous hot melt pavement marker adhesive Georgia test deck : two year evaluation (fall 2006 product submissions).

    Science.gov (United States)

    2008-10-01

    Purpose: : The purpose of the National Transportation Product Evaluation Program (NTPEP) is to provide a cost-effective method of evaluation for materials of common interest among all participating NTPEP member departments. NTPEP reports allow member...

  14. Evaluation of co-cokes from bituminous coal with vacuum resid or decant oil, and evaluation of anthracites, as precursors to graphite

    Science.gov (United States)

    Nyathi, Mhlwazi S.

    2011-12-01

    Graphite is utilized as a neutron moderator and structural component in some nuclear reactor designs. During the reactor operaction the structure of graphite is damaged by collision with fast neutrons. Graphite's resistance to this damage determines its lifetime in the reactor. On neutron irradiation, isotropic or near-isotropic graphite experiences less structural damage than anisotropic graphite. The degree of anisotropy in a graphite artifact is dependent on the structure of its precursor coke. Currently, there exist concerns over a short supply of traditional precursor coke, primarily due to a steadily increasing price of petroleum. The main goal of this study was to study the anisotropic and isotropic properties of graphitized co-cokes and anthracites as a way of investigating the possibility of synthesizing isotropic or near-isotropic graphite from co-cokes and anthracites. Demonstrating the ability to form isotropic or near-isotropic graphite would mean that co-cokes and anthracites have a potential use as filler material in the synthesis of nuclear graphite. The approach used to control the co-coke structure was to vary the reaction conditions. Co-cokes were produced by coking 4:1 blends of vacuum resid/coal and decant oil/coal at temperatures of 465 and 500 °C for reaction times of 12 and 18 hours under autogenous pressure. Co-cokes obtained were calcined at 1420 °C and graphitized at 3000 °C for 24 hours. Optical microscopy, X-ray diffraction, temperature-programmed oxidation and Raman spectroscopy were used to characterize the products. It was found that higher reaction temperature (500 °C) or shorter reaction time (12 hours) leads to an increase in co-coke structural disorder and an increase in the amount of mosaic carbon at the expense of textural components that are necessary for the formation of anisotropic structure, namely, domains and flow domains. Characterization of graphitized co-cokes showed that the quality, as expressed by the degree of graphitization and crystallite dimensions, of the final product is dependent on the nature of the precursor co-coke. The methodology for studying anthracites was to select two anthracites on basis of rank, PSOC1515 being semi-anthracite and DECS21 anthracite. The selected anthracites were graphitized, in both native and demineralized states, under the same conditions as co-cokes. Products obtained from DECS21 showed higher degrees of graphitization and larger crystallite dimensions than products obtained from PSOC1515. Demineralization of anthracites served to increase the degree of graphitization, indicating that the minerals contained in these anthracites have no graphitization-enhancing ability. A larger crystallite length for products obtained from native versions, compared to demineralized versions, was attributed to a formation and decomposition of a silicon carbide during graphitization of native versions. In order to examine the anisotropic and isotropic properties, nuclear-grade graphite samples obtained from Oak Ridge National Laboratory (ORNL) and commercial graphite purchased from Fluka were characterized under similar conditions as graphitized co-cokes and anthracites. These samples served as representatives of "two extremes", with ORNL samples being the isotropic end and commercial graphite being the anisotropic end. Through evaluating relationships between structural parameters, it was observed that graphitized co-cokes are situated, structurally, somewhere between the "two extremes", whereas graphitized anthracites are closer to the anisotropic end. Basically, co-cokes have a better potential than anthracites to transform to isotropic or near-isotropic graphite upon graphitization. By co-coking vacuum resid/coal instead of decant oil/coal or using 500 °C instead of 465 °C, a shift away from commercial graphite towards ORNL samples was attained. Graphitizing a semi-anthracite or demineralizing anthracites before graphitization also caused a shift towards ORNL samples.

  15. Efecto de la tenacidad del asfalto en la resistencia a fatiga de las mezclas asfálticas Asphalt toughness effect on bituminous mixture fatigue behavior

    OpenAIRE

    Alfredo H Noguera; Rodrigo Miró

    2011-01-01

    Uno de los parámetros más importantes para definir el comportamiento de la mezcla en servicio es la tenacidad que el asfalto proporciona al aglomerar los agregados, es decir, la energía que se disipa al fracturar la mezcla, entre mayor sea dicha energía mejor será su calidad. Y por lo tanto, deberá existir una relación si dicha cantidad de energía se disipa en un ciclo de carga (tracción) o con muchos ciclos durante el tiempo (fatiga). El objetivo de éste trabajo es establecer una relación en...

  16. BITUMINOUS MIX RESPONSE TO PLASTIC DEFORMATIONS: COMPARISON OF THE SPANISH NLT-173 AND UNE-EN 12697-22 WHEEL-TRACKING TESTS

    Directory of Open Access Journals (Sweden)

    GEMA GARCÍA-TRAVÉ

    2012-01-01

    Full Text Available La formación de roderas es uno de los mayores deterioros que se producen en los firmes flexibles, lo que ocasiona la pérdida de regularidad superficial que repercute de forma negativa en la calidad del servicio prestado a los usuarios. Existen distintos ensayos de laboratorio que permiten evaluar las deformaciones plásticas producidas en las capas del pavimento, entre ellos podemos destacar los ensayos de simulación. El objetivo de esta investigación es analizar el comportamiento de una mezcla bituminosa en caliente frente a deformaciones plásticas, mediante dos métodos de ensayo diferentes; ensayo en pista de laboratorio de acuerdo a la normativa española NLT-173 y el ensayo de rodadura UNE-EN 12697-22 (ensayo obligatorio tras la entrada en vigor del Marcado CE de mezclas bituminosas en 2008. La finalidad última de este artículo es formular una propuesta de modificación de la normativa española (PG-3 sobre los límites exigibles en éste último ensayo.

  17. The effect of aggregate type and mix design on the wet skid resistance of bituminous pavement : recommendations for Virginia's Wet Accident Reduction Program.

    Science.gov (United States)

    1995-01-01

    This report (1) identified and characterized Virginia's nonpolishing aggregates in terms of their wet skid resistance, (2) compared the standard ASTM E 274-90 skid test to the British Accelerated Polishing Machine (BAPM) and British PendulumTester (B...

  18. Fluid-dynamical and poro-elastic coupling of gas permeability of inert and sorbing gases on an Australian sub-bituminous coal

    Science.gov (United States)

    Gensterblum, Y.; Krooss, B. M.

    2013-12-01

    The interaction and the coupling of slip-flow, a fluid dynamic phenomenon, and the cleat volume compressibility which is a poroelastic phenomenon has been investigated on two samples from the Taroom coal measure, Surat Basin, Queensland Australia. Measurements were performed using inert (helium and argon) and sorbing gases (nitrogen, methane and carbon dioxide) at controlled effective stress. We observed the following regular sequence of permeability coefficients for the different gases: Helium >> argon => nitrogen > methane >> CO2 Even after slip-flow correction, different intrinsic permeability coefficients are obtained for the same sample if different gases are used in the tests. The permeability values determined with helium are largest while those measured with CO2 are lowest. Inert gases like helium and argon show higher apparent- and even slip flow-corrected permeability coefficients than sorbing gases like methane or carbon dioxide. This observation is contrary to the prediction that the slip-flow corrected permeability have to be the same for all gases. The cleat volume compressibility cf was evaluated using the 'matchstick approach' [1, 2]. The cleat volume compressibility coefficients cf are almost identical for the two samples taken from the same well. However, for one sample a strong dependence of the cf with the mean pore pressure was observed. This is attributed to a strong slip-flow effect caused by a narrow cleat system as compared to the sister sample. The cleat volume compressibility coefficient cf is almost the same for inert and sorbing gases. We conclude that the occurrence of slip-flow in coals is able to compensate the permeability reduction resulting from increasing effective stress. This should lead to a much higher productivity of coal bed methane reservoirs in the third production phase (pseudo-steady state phase; [3]). This conclusion appears to be also valid for shale gas and tight gas reservoirs, where the gas transport takes place in meso- and micropores, as well.

  19. Blackened bioclasts and bituminous impregnations in the Koněprusy Limestone (Lover Devonian), the Barrandian area, Czech Republic: Implications for basin analysis

    Czech Academy of Sciences Publication Activity Database

    Suchý, V.; Sýkorová, Ivana; Dobeš, P.; Machovič, Vladimír; Filip, Jiří; Zeman, Antonín; Stejskal, M.

    2012-01-01

    Roč. 58, č. 4 (2012), s. 759-777 ISSN 0172-9179 R&D Projects: GA ČR GA205/09/1162 Institutional support: RVO:67985891 ; RVO:68378297 ; RVO:67985831 Keywords : blackened bioclasts * bitumen * reef carbonates Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.771, year: 2012

  20. Morphology and microstructure of co-pyrolysis char from bituminous coal blended with lignocellulosic biomass: Effects of cellulose, hemicellulose and lignin

    International Nuclear Information System (INIS)

    Wu, Zhiqiang; Yang, Wangcai; Chen, Lin; Meng, Haiyu; Zhao, Jun; Wang, Shuzhong

    2017-01-01

    Highlights: • Influence of biomass model compounds on co-pyrolysis char structure was investigated. • Transformation of carbon structure was explored by Raman and spectral deconvolution. • Evolution of surface morphology was quantitatively described by the fractal analysis. • Three biomass model compounds showed different influence on the structure evolution. - Abstract: Co-pyrolysis of coal and lignocellulose biomass and coal is the key step of other co-thermochemical conversion, and conversion of co-pyrolysis char is the rate-determining step of co-gasification and co-combustion. In this paper, the influence of biomass model compounds (cellulose, hemicellulose, and lignin, abbreviated as CE, HCE and LIG) on the co-pyrolysis char structure transformation was investigated. Carbon structure and surface morphology of co-pyrolysis char were examined by Raman spectroscopy and scanning electron microscope (SEM). A comprehensive comparison of Raman spectral deconvolution methods based on various fitting functions and peak numbers was explored, and Gaussian-Lorentzian-function with no less than nine peaks showed the best performance. Three biomass model show different effects on the transformation of microstructure structure. The addition of CE increased the ordering of char structure. HCE promoted the disordering degree of microstructure structure and reached the maximum at 50% HCE mass ratio. The microstructure structure changes of co-pyrolysis char for 25% and 50% LIG mass ratios were not evident, while 75% LIG increased the disordering degree of the co-pyrolysis char. Fractal analysis was applied for describing the char surface morphology quantitatively with two and three-dimensional fractal dimensions. CE decreased the fractal dimensions of co-pyrolysis, and the influence of HCE and LIG depended on the mass ratio.

  1. Development of Advanced Manufacturing Methods for Warm White LEDs for General Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Deshpande, Anirudha; Kolodin, Boris; Jacob, Cherian; Chowdhury, Ashfaqul; Kuenzler, Glenn; Sater, Karen; Aesram, Danny; Glaettli, Steven; Gallagher, Brian; Langer, Paul; Setlur, Anant; Beers, Bill

    2012-03-31

    GE Lighting Solutions will develop precise and efficient manufacturing techniques for the “remote phosphor” platform of warm-white LED products. In volume, this will be demonstrated to drive significant materials, labor and capital productivity to achieve a maximum possible 53% reduction in overall cost. In addition, the typical total color variation for these white LEDs in production will be well within the ANSI bins and as low as a 4-step MacAdam ellipse centered on the black body curve. Achievement of both of these objectives will be demonstrated while meeting a performance target of > 75 lm/W for a warm-white LED and a reliability target of <30% lumen drop / <2-step MacAdam ellipse shift, estimated over 50,000 hrs.

  2. Estimation of the real colour gamut

    OpenAIRE

    Perales Romero, Esther; Chorro Calderón, Elísabet; Viqueira Pérez, Valentín; Martínez Verdú, Francisco Miguel

    2009-01-01

    Comunicación presentada en AIC 2009, 11th Congress of the International Colour Association (AIC), 27 September-2 October 2009, University of New South Wales, Sydney, Australia. In the present work, we have assessed the gamut of colour surfaces currently available for different colour technologies. Their colour reproduction capability have been analyzed by plotting CIELAB data under the illuminant D65 into constant lightness and hue-angle planes to be compared with MacAdam limits which defi...

  3. What factors affect the carriage of epinephrine auto-injectors by teenagers?

    OpenAIRE

    Macadam, C; Barnett, J; Roberts, G; Stiefel, G; King, R; Erlewyn-Lajeunesse, M; Holloway, JA; Lucas, JS

    2012-01-01

    Copyright @ 2012 Macadam et al; licensee BioMed Central Ltd. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. This article is made available through the Brunel Open Access Publishing Fund. BACKGROUND: Teenagers with allergies are at particular risk of severe and f...

  4. Development of clean coal and clean soil technologies using advanced agglomeration technologies

    International Nuclear Information System (INIS)

    Ignasiak, B.; Pawlak, W.; Szymocha, K.; Marr, J.

    1990-04-01

    The specific objectives of the bituminous coal program were to explore and evaluate the application of advanced agglomeration technology for: (1)desulphurization of bituminous coals to sulphur content acceptable within the current EPA SO 2 emission guidelines; (2) deashing of bituminous coals to ash content of less than 10 percent; and (3)increasing the calorific value of bituminous coals to above 13,000 Btu/lb. (VC)

  5. Appalachian basin bituminous coal: sulfur content and potential sulfur dioxide emissions of coal mined for electrical power generation: Chapter G.5 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Science.gov (United States)

    Trippi, Michael H.; Ruppert, Leslie F.; Attanasi, E.D.; Milici, Robert C.; Freeman, P.A.

    2014-01-01

    Data from 157 counties in the Appalachian basin of average sulfur content of coal mined for electrical power generation from 1983 through 2005 show a general decrease in the number of counties where coal mining has occurred and a decrease in the number of counties where higher sulfur coals (>2 percent sulfur) were mined. Calculated potential SO2 emissions (assuming no post-combustion SO2 removal) show a corresponding decrease over the same period of time.

  6. Estimate of cost of plant producing 125,000 t/ann. DHD feed for 100,000 t/ann. high performance gasoline from bituminous coal, at Ludwigshafen-Oppau

    Energy Technology Data Exchange (ETDEWEB)

    1942-11-03

    The first table was a summary showing the costs in Reichsmarks as follows: (1) hydrogen production--RM 20,700,000; (2) hydrogenation proper--RM 40,000,000; (3) hygas cleaning--RM 1,400,000; (4) power production RM 7,000,000; (5) power distribution--RM 4,000,000; (6) auxiliary plants--RM 11,000,000; and (7) miscellaneous--5,500,000 RM. The total cost was given as RM 90,000,000. A table showing the cost of hydrogen production broken down into smaller units showed the water gas plant for 50,000 m/sup 3//hr of hydrogen at RM 6,500,000 as the major cost, followed closely by compression to 325 atm at RM 5,000,000. Catalytic hydrogen production at RM 2,300,000 and CO/sub 2/ cleaning at RM 2,000,000 were also major factors in the cost. The major cost for hydrogenation proper was the liquid phase costing RM 25,300,000, with the vapor phase costing RM 9,900,000 for 300 atm processing or RM 12,200,000 for 700 atm processing. In the liquid phase, two four-stage coal stalls cost RM 10,000,000, while the paste press division, coal preparation division, and circulating gas wash cost RM 2,400,000, RM 2,300,000, and RM 2,000,000 respectively. In the vapor phase, four stalls would cost RM 5,400,000 for 300 atm or RM 7,300,000 for 700 atm. Hydrogenation gas cleaning showed the Claus Plant, which appeared to be oxygen-burning, as the main cost at RM 600,000. The major cost of power production was shown by the expansion of the power plant by one boiler and one turbine with a cost of RM 5,000,000. The main cost for power distribution was electric power lines which cost RM 2,000,000. The major costs for auxiliary plants were in construction and the miscellaneous heading included such things as catalysts, design, and construction.

  7. Specific provisions applicable to the production, inspection, treatment, packaging and interim storage of low and medium level bituminized wastes resulting from the reprocessing of fuels irradiated in pressurized water reactors

    International Nuclear Information System (INIS)

    1984-04-01

    The Fundamental Safety Rules applicable to certain types of nuclear installation are intended to clarify the conditions of which observance, for the type of installation concerned and for the subject that they deal with, is considered as equivalent to compliance with regulatory French technical practice. These Rules should facilitate safety analysises and the clear understanding between persons interested in matters related to nuclear safety. They in no way reduce the operator's liability and pose no obstacle to statutory provisions in force. For any installation to which a Fundamental Safety Rule applies according to the foregoing paragraph, the operator may be relieved from application of the Rule if he shows proof that the safety objectives set by the Rule are attained by other means that he proposes within the framework of statutory procedures. Furthermore, the Central Service for the Safety of Nuclear Installations reserves the right at all times to alter any Fundamental Safety Rule, as required, should it deem this necessary, while specifying the applicability conditions. This rule sets forth the specific provisions applicable to the production, inspection, treatment, packaging and interim storage of the wastes, resulting from the reprocessing of fuels irradiated in a PWR and coated in bitumen

  8. Collection and record-keeping activities on operational records in the BDF (Bituminization development facility). Investigation of the cause of fire and explosion, and preventing measures-against recurrence

    International Nuclear Information System (INIS)

    Kobayashi, K.; Nakazawa, Y.; Numata, S.; Sasaki, A.; Yamauchi, T.

    1998-01-01

    On March 11 1997, a fire and explosion accident occurred at the BDF of the Tokai Works of PNC. The facility was under operation to solidify low level radioactive liquid waste. All the operational records necessary to determine the root cause of the accident including data sheets, operation reports, and related instruments and controller records were collected and taken on films immediately. They were rearranged in each taken order and compiled each recorded time. Further, the filmed data were processed digital images in compact disks and input to personal computer database. In addition, the computerized records of extruder operating temperature variation, its torque variation and its rotation change each batch were restored actual size at the accident time. This report is concerned with the work of collection and record-keeping of the operational records related to the accident. (H. Itami)

  9. アスファルト混合物の摩耗抵抗改善に関する実験的研究

    OpenAIRE

    新田, 登; 磯崎, 真一

    1987-01-01

    The development of wear resistant bituminous paving mixtures has been considered as one of the important problems in the field of bituminous pavement design in cold regions. In order to contribute to this problem, a series of laboratory tests used an accelerated wearing equipment were made on wearing resistance properties of bituminous mixtures: one is on the wearing process, another is on the effects of mixture components, including volume, size and gradation of coarse aggregate and types of...

  10. RESOURCE SAVING IN CONSTRUCTION INDUSTRY WITH HIGHWAY BRANCH AS EXAMPLE

    OpenAIRE

    A. V. Roudensky

    2011-01-01

    Consumption of energy is an objective (independent on cost fluctuations) technical efficiency criterion of any construction or repair work. Highway/road (particularly bituminous pavement) sector is an important construction industry part. Bituminous road pavement construction consists of such components as excavation and preparation of basic materials, manufacture of mixes, ready mix laying/compacting and transportation of all materials. Average energy consumption for every bituminous pavemen...

  11. Design of SMA - 13 asphalt mixture ratio on Z3and Z18 of the capital airport

    Science.gov (United States)

    Tian, Shuaituan; Ye, Song; Kong, Fandong

    2017-12-01

    According to the demand of T2 terminal airlines to operate A380 models, to meet the smooth running of the A380 airliner at the west end of the Capital Airport, So Z3 and Z18 taxiway area of the transformation is imperative. According to the design, the upper layer of this project adopts SMA - 13 modified asphalt mastic macadam mixture. We design the SMA-13 modified asphalt mixture on Z3 and Z18 of the capital airport from any respects, including coarse and fine aggregate, filler, asphalt, fiber and anti-rutting agent, and we hope we can find the best SMA-13 modified asphalt mixture.

  12. Dynamic Finite Element Investigation of Wave Attack on Sea Dikes : A Coupled Approach using Plate and Volume Elements

    NARCIS (Netherlands)

    Tan, S.

    2016-01-01

    Approximately 400 kilometres of Dutch sea dikes are protected by bituminous concrete revetments to prevent damage from erosion and repeated wave attacks during storms. The numerical analysis of sea dikes subjected to cyclic wave loading needs to consider the behaviour of the bituminous concrete

  13. Thermal stability of carboxylic acid functionality in coal; Sekitanchu ni sonzaisuru karubokishiruki no netsubunkai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, Y.; Aida, T. [Kinki University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    Carboxyl in coal was focused in discussing its pyrolytic behavior while tracking change of its absolute amount relative to the heating temperatures. A total of four kinds of coals, consisting of two kinds brown coals, sub-bituminous coal and bituminous coal were used. Change in the absolute amount of carboxyl due to heating varies with coalification degree. Decomposition starts in the bituminous coal from around 300{degree}C, and is rapidly accelerated when 400{degree}C is exceeded. Carboxyls in brown coals exist two to three times as much as those in bituminous and sub-bituminous coals, of which 40% is decomposed at a temperature as low as about 300{degree}C. Their pyrolytic behavior at temperatures higher than 400{degree}C resembles that of the bituminous coal. Carboxyls consist of those easy to decompose and difficult to decompose. Aromatic and aliphatic carboxylic acids with simple structure are stable at temperatures lower than 300{degree}C, and decompose abruptly from about 400{degree}C, hence their behavior resembles that of carboxyls in bituminous and sub-bituminous coals. Structure of low-temperature decomposing carboxyls in brown coals is not known, but it is assumed that humic acid originated from natural materials remains in the structure. 4 refs., 3 figs., 1 tab.

  14. METHANE de-NOX for Utility PC Boilers

    Energy Technology Data Exchange (ETDEWEB)

    Bruce Bryan; Joseph Rabovitser; Serguei Nester; Stan Wohadlo

    2004-12-31

    Preparations for conducting large-scale combustion tests with caking bituminous coal continued during the start of this quarter. Major project accomplishments related to bituminous coal testing included: a CFD preheat model and evaluation, an update of the process flow diagram and a detailed preheat burner mechanical design (suitable for construction) for firing bituminous coal. Installation and testing of the 85 MMBtu/h bituminous coal preheating system was planned to take place before the end of December. Based on the inability to conduct testing in Riley's Commercial Burner Test Facility (CBTF) during freezing weather, a schedule review indicated required site work for testing bituminous coal at the CBTF could not be completed before freezing weather set in at the site. Further bituminous preheat modification work was put on hold and efforts turned to securing the test facility over the winter season. Bituminous coal tests are therefore delayed; April-May 2005 is earliest estimate of when testing can resume. A request for a time extension was submitted to DOE to extend the project through September 2005 to allow time to secure additional funding and complete the bituminous coal testing. Removal of the PRB PC Preheater from the CBTF burner deck was completed. Decommissioning of the CBTF for the winter was also completed.

  15. Trees for strip-mined lands

    Science.gov (United States)

    George Hart; William R. Byrnes

    1960-01-01

    Open-pit or strip mining has become an important method of mining bituminous coal in Pennsylvania. In 1958 some 19.5 million tons of soft coal - 29 percent of the total bituminous production in the State - were produced by this method.

  16. 77 FR 67337 - Certain Activated Carbon From the People's Republic of China; 2010-2011; Final Results of...

    Science.gov (United States)

    2012-11-09

    ....\\7\\ The products are currently classifiable under the Harmonized Tariff Schedule of the United States... Considerations A. Anthracite Coal B. Bituminous Coal C. Carbonized Material D. Hydrochloric Acid E. Labor F... V: VALUATION OF JACOBI'S CONSUMPTION OF BITUMINOUS COAL FOR HEATING COMMENT VI: VALUATION OF JACOBI...

  17. Fly Ash Amendments Catalyze Soil Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Amonette, James E.; Kim, Jungbae; Russell, Colleen K.; Palumbo, A. V.; Daniels, William L.

    2003-09-15

    We tested the effects of four alkaline fly ashes {Class C (sub-bituminous), Class F (bituminous), Class F [bituminous with flue-gas desulfurization (FGD) products], and Class F (lignitic)} on a reaction that simulates the enzyme-mediated formation of humic materials in soils. The presence of FGD products completely halted the reaction, and the bituminous ash showed no benefit over an ash-free control. The sub-bituminous and lignitic fly ashes, however, increased the amount of polymer formed by several-fold. The strong synergetic effect of these ashes when enzyme is present apparently arises from the combined effects of metal oxide co-oxidation (Fe and Mn oxides), alkaline pH, and physical stabilization of the enzyme (porous silica cenospheres).

  18. Sequential solvent extraction for the modes of occurrence of selenium in coals of different ranks from the Huaibei Coalfield, China

    Directory of Open Access Journals (Sweden)

    Wang Lei

    2007-12-01

    Full Text Available Abstract Forms of selenium in bituminous coal, anthracite, and cokeite (natural coke from Huaibei Coalfield, Anhui, China, have been determined by sequential solvent extraction. The selenium content in bulk samples is 4.0, 2.4, and 2.0 μg/g in bituminous coal, anthracite, and cokeite, respectively. The six forms of selenium determined by six-step solvent extraction are water-leachable, ion-exchangeable, organic matter-associated, carbonate-associated, silicate-associated, and sulfide-associated. The predominant forms of selenium in bituminous coal are organic matter-associated (39.0%, sulfide-associated (21.1%, and silicate bound (31.8%; these three forms account for 92% of the total. The organic matter bound-selenium decrease dramatically from bituminous coal (39.0% to anthracite (11.6% and to cokeite (0%, indicating that organic matter bound selenium is converted to other forms during metamorphism of the coal, most likely sulfide-form. The sulfide-associated form increased remarkably from bituminous coal (21.1% to anthracite (50.4% and cokeite (54.5%, indicating the formation of selenium sulfide, possibly in pyrite during the transformation of bituminous coal to anthracite and cokeite. The silicate-associated selenium in bituminous coal (31.8% is much higher than that in anthracite (16.4% and cokeite (15.8%, indicating that silicate-associated selenium is partly converted to sulfide during metamorphism.

  19. Report on results for fiscal 1997 (B edition) on development of coal liquefaction technology. Development of bituminous coal liquefaction technology (research by pilot plant) 1/2; 1997 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B gan). Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu) 1/2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    Through the design, construction and operation of a pilot plant, the NEDOL method was verified, with its operation technology established, and also with a target set in collecting and accumulating data and knowledge required for a commercial plant in the future. With the Run-2, 3, 4 implemented using operating basis coal as the material, the operating stability of equipment/machines was confirmed, and a method of obtaining material balance as well as the operation technology was established, thereby demonstrating the NEDOL process, proving a long-term continuous operability and verifying the highest liquefaction yield. In addition, various process data, engineering data, operation control data, etc., were acquired, classified and analyzed. In the Run-3/4-1, a long-term coal charging continuous operation for 80 days was achieved, as was a high liquefaction yield of 58%. Moreover, data of material balance and thermal balance were obtained, with the performance confirmed of various kinds of equipment. Using the operating basis coat as the material, the coal charging operation of the Run-4-2 was commenced, with the performance verification test carried out for a neutron attenuation tracer method (NAT method), for the purpose of obtaining data of the flow characteristics of the liquefaction reaction tower. (NEDO)

  20. Achievement report on developing coal liquefaction technologies in fiscal 1998 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant) 2/2; 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. 2/2. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1998. In the operation study, the coal charging operation has been carried out for 269 days (6,169 hours) in total since the operation has been launched, and the targets were achieved. In the facility repairs, periodical inspections were performed including daily maintenance during the operation, the legal inspection on the boiler and the pressure vessel of the category one after completing the RUN-5, and disassembling and opening inspections on other devices. After having completed the RUN-6 and 7, the final verification inspection and the facility rinsing were performed after the operation studies have been completed. The data acquired in the facility maintenance were summarized as part of the technological package after the assessment. The investigative researches have executed development of a liquefying reaction simulator, tests and investigations on pulverization of the liquefying catalyst, evaluation on the activity of the used hydrogenating catalyst, and investigation on the effect of the coal liquefaction facilities and products on the environment. The technologies were investigated on coal liquefaction, and the plans for disassembling studies were established. (NEDO)

  1. Fiscal 1998 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1998 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. For the modification of facilities, product oil reforming facilities were installed. In the coal injection operation, a 59-day slurry operation was carried out using Tanito Harum coal, which was for the evaluation of the reforming effect under the product reforming conditions, operationality, and liquefaction characteristics. A 37-day slurry operation was also performed using Chinese coal, which was intended to pursue improved cost performance and to collect the light oil fraction in the flow of reforming operation. In the operation for maintenance, investigations were conducted into conditions for hydrogenation in a 1-through operation involving the solvent hydrogenation process and the normal pressure distillation facilities and into the effect of pre-hydrogenation solvent properties, which aimed at grasping the effect of product oil reforming measures and their influence on operationality. In the survey of environments, the properties of wastewater from the liquefaction process using Tanito Harum coal were studied and toxicity evaluation tests were conducted for activated sludge. (NEDO)

  2. Achievement report on developing coal liquefaction technologies in fiscal 1998 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant) 1/2; 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. 1/2. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1998. In the operation study RUN-5, the operation was carried out by using the Tanito Harum coal of Indonesia, and raising the slurry concentration to 50% by weight. The operation stability when the high concentration slurry was used was verified, and the liquefying reaction column fluidity property data, and the material balance and heat balance data were acquired by using the NAT method. In the RUN-6 and 7, for the purpose of verifying the applicability of the NEDOL process to the wide range of coal types as the process feature, the Adaro coal of Indonesia and the Ikejima coal of Japan were used, and the operation at high slurry concentration was performed at 80% load and under the standard NEDOL conditions. The operation stability when the upper and lower limit coals was used was verified, and the operability at high slurry concentration was identified. At the same time, the liquefying reaction column fluidity property data, and the material balance and heat balance data were acquired. The development targets established by the Industrial Technology Council have all been achieved. (NEDO)

  3. Fiscal 1997 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1997 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. In the modification of facilities, equipment and devices were procured for the product oil reforming facilities and their installation was partly accomplished. In the coal injection operation, a 60-day slurry operation was conducted, using coal types of the upper limit and lower limit qualities, for expanding the scope of coal types applicable to the NEDOL process and for exploring optimum conditions, and another operation of 37 days was conducted using Chinese coal and Chinese-prepared liquefaction catalysts, and the two operations were studied for difference in yields and in operationality. Characteristics of the liquefaction reactors were investigated and basic studies were made relative to the physical property of the yielded coal oil. In the operation for maintenance, the 1st liquefaction reactor was singly operated for an 8-day slurry operation, which was to check the progress of liquefaction in a 1-reactor setup. Concerning the reforming of the product oil, the hydrogenation reactors were checked for their response to temperature control. Moreover, hydrogenation solvents were produced for the PSU and for China. (NEDO)

  4. Achievement report on developing coal liquefaction technologies in fiscal 1999 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant); 1999 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1999. In the disassembling study, wear, corrosion, and wall thickness change were investigated, and non-destructive inspection was performed on the major four facilities, and such newly developed devices as the liquefying catalyst manufacturing facilities, the slurry heat exchanger, and the let-down valves. The sampled test pieces were investigated of changes in the mechanical properties by means of the metallic structure inspection, hardness test, tensile test, and impact test. Deposits in the devices were investigated of their depositing conditions and constituents. The result reveals that the 3 Cr-1Mo-1/4V-Ti-B steel developed for the high-temperature, high-pressure, and hydrogen environment of the coal liquefaction plant showed excellent low-temperature tenacity and maintained good characteristics. No problems were discovered in corrosion resistance if PP using materials are used. The slurry handling centrifugal pump and instrumentation vales were worn out severely requiring replacements during the operation, for which further discussions are desired to be given. (NEDO)

  5. Fiscal 1996 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1996 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. In the modification of facilities, detailed designs were prepared for product oil reforming facilities and some equipment and devices were procured. In addition, the 3rd liquefaction reactor cone section and the neutron attenuation-aided measuring device were refurbished. In the injection of coal, a 62-day and 23-day slurry injection operations were accomplished using Tanito Harum coal, when the impact imposed on the yield of the product, etc., by the change of liquefaction catalysts and by gas phase hydrogen concentration enriching conditions was investigated, and the unit was examined for operationality. During a 42-day operation for maintenance, the unit was operated using only the slurry heater for the investigation of the initial reaction in liquefaction, and studies were conducted about the heater exit temperature, G/L (gas-liquid ratio), and the effect to ensue from the use of a different solvent. In the effort to develop and evaluate new materials, implantation tests were conducted for metallic materials and the 3rd liquefaction reactor was subjected to a non-destructive inspection. Wastewater from the process was examined for quality, and environment-related measurements were performed for the atmosphere. (NEDO)

  6. RESOURCE SAVING IN CONSTRUCTION INDUSTRY WITH HIGHWAY BRANCH AS EXAMPLE

    Directory of Open Access Journals (Sweden)

    A. V. Roudensky

    2011-01-01

    Full Text Available Consumption of energy is an objective (independent on cost fluctuations technical efficiency criterion of any construction or repair work. Highway/road (particularly bituminous pavement sector is an important construction industry part. Bituminous road pavement construction consists of such components as excavation and preparation of basic materials, manufacture of mixes, ready mix laying/compacting and transportation of all materials. Average energy consumption for every bituminous pavement construction component is assessed. Approach to resource and energy saving presented in the article may be used in construction industry to develop and implement innovativetechnical and organizational solutions both of general application and for individual projects.

  7. Efeito do transtorno depressivo maior na percepção de cor em adultos

    OpenAIRE

    Espínola, Everton de Lira

    2013-01-01

    A capacidade discriminativa de cores tem sido utilizada como forma de avaliação da percepção de cores em condições neuropsiquiátricas. No presente estudo investigou-se a existência de possíveis alterações na percepção de cores em adultos com Transtorno Depressivo Maior, utilizando-se como parâmetros os limiares de discriminação para os eixos de confusão Protan, Deutan e Tritan, a área da elipse de MacAdam e sua elipticidade. O estudo contou com 23 voluntários, sendo 11 com depressão maior (Gr...

  8. Computation of radiative image formation in isolated source and collimated irradiation problems

    Energy Technology Data Exchange (ETDEWEB)

    Li Hongshun [School of Energy and Power Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)]. E-mail: lihs_hust@yahoo.com.cn; Werther, Joachim [Chemical Engineering I, Technical University Hamburg-Harburg, Denickestrasse 15, 21071 Hamburg (Germany)

    2006-01-15

    Due to the ray effect, it is not suitable to employ the discrete ordinates method to calculate the radiation field and the image-formation process in radiative problems with isolated radiative sources (such as point and line sources, isolated medium or boundary source). In this paper, a hybrid method, named Monte Carlo-discrete ordinates method (Macadam) is developed. Firstly, the Monte Carlo method is used to calculate the emission process. Secondly, the discrete ordinates method is employed to calculate the scattering process, correspondingly, an alternative energy partitioning method is proposed to combine the above two conventional methods. Thirdly, the DOS+ISW algorithm (JQSRT, 2003, 78: 437-453) is used to calculate the image-formation process. Finally, the MCDOM is applied to computing the image formation of an endoscope, which was used to study the hydrodynamics of circulating fluidized beds (Powder Technology, 2001;114:71-83)

  9. Installation report : evaluation of recycled hot mix asphaltic concrete on Route 220.

    Science.gov (United States)

    1982-01-01

    This report describes a project in which the bituminous pavement on an approximately 8-mi. (13-km) section of roadway was removed, recycled through a conventional asphalt batch plant, and relaid. The project was accomplished with little difficulty an...

  10. Great Lakes/St. Lawrence Seaway Regional Transportation Study; Great Lakes Area Industries.

    Science.gov (United States)

    1981-11-01

    18.6 1.8 21.5 22.0 * Pacific Rim countries are Hong Kong, Japan, the Philippines, Peoples Republic of China, India and Korea. Source: Agrizultural...Illinois Bituminous 10,775 2.92 11.4 Alabama Bituminous 11,740 1.43 14.1 Texas Lignite 6,601 0.66 12.0 Colorado Bituminous 10,925 0.49 9.4 Wyoming...Subbituminous 9,037 0.50 8.3 Utah Bituminous 11,569 0.63 11.9 North Dakota Lignite 6,556 0.65 9.9 Montana Subbituminous 8,957 0.64 7.6 Pennsylvania

  11. Best practices and performance assessment for preventive maintenance treatments for Virginia pavements.

    Science.gov (United States)

    2015-08-01

    Preventive maintenance has the potential to improve network condition by retarding future pavement deterioration. This : report outlines guidelines for implementing a preventive maintenance policy for bituminous pavements. : Preventive maintenance tr...

  12. Seal coat research project

    Science.gov (United States)

    1999-12-01

    This study evaluates the use of seal coating as a method to protect bituminous pavements from oxidation, water infiltration, and raveling. The Minnesota Department of Transportation (Mn/DOT) applied seal coating to a roadway segment of Trunk Highway ...

  13. Chip seal performance measures : best practices.

    Science.gov (United States)

    2015-03-01

    The Washington State Department of Transportation (WSDOT) has a long history of designing, constructing, : and maintaining chip seal or bituminous surface treatment pavements. However, to date WSDOT has not : developed pavement performance indicators...

  14. Review and analysis of Hamburg Wheel Tracking Device test data : [technical summary].

    Science.gov (United States)

    2014-02-01

    Approximately 89% of the paved-road network in Kansas is asphalt surfaced (bituminous and : composite). According to the Kansas Department of Transportation (KDOT), typical design : performance period of hot-mix asphalt (HMA) pavement for new constru...

  15. Saw & seal, airport pavement.

    Science.gov (United States)

    2009-05-01

    Due to extreme cold temperatures, hot bituminous pavements on Maines airports are subject to transverse : or thermal cracking. This can lead to poorly performing pavement structure causing heaving and : settlement problems. Studies have shown that...

  16. Effect of waste plastic as modifier on thermal stability and degradation kinetics of bitumen/waste plastics blend

    International Nuclear Information System (INIS)

    Naskar, M.; Chaki, T.K.; Reddy, K.S.

    2010-01-01

    Different modified bituminous binders are used in pavement construction for improved durability and for enhanced performance in resisting cracking and permanent deformation of bituminous layers. Waste plastics, whose disposal is a matter of concern, have been used successfully for modifying bitumen. This paper reports the thermogravimetric studies conducted on waste plastic modified bituminous binders. Modified bituminous binders prepared using different plastic contents (0-7 wt% by weight of bitumen) were investigated. The activation energies were determined from thermogravimetric analysis (TGA) data using Kissinger and the Flynn-Wall-Ozawa methods, which do not require knowledge of the reaction mechanism. Modified bitumen (WPMB5) with 5 wt% plastic was found to have the highest thermal stability compared to other binders investigated. Differential scanning calorimetry (DSC) studies were carried out to find crystalline melting temperature and fusion enthalpy. Rheological parameters of modified binders prepared with different plastic contents also suggest that the 5 wt% plastic content is expected to yield optimal performance.

  17. 40 CFR 61.143 - Standard for roadways.

    Science.gov (United States)

    2010-07-01

    ... mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must... for Construction of Roads and Bridges on Federal Highway Projects, FP-85, 1985, or their equivalent. ...

  18. Field evaluation of skid resistant surfaces : final report : part I.

    Science.gov (United States)

    1970-06-01

    This project was undertaken to establish a thin bituminous surface course that would possess good skid resistant qualities as well as, being both economical and durable. : This is the final report on the evaluation of skid resistant surfaces which wa...

  19. Soot, organics, and ultrafine ash from air- and oxy-fired coal combustion

    Data.gov (United States)

    U.S. Environmental Protection Agency — Pulverized bituminous coal was burned in a 10W externally heated entrained flow furnace under air-combustion and three oxy-combustion inlet oxygen conditions (28,...

  20. an experimental study on the use of polypropylene waste

    African Journals Online (AJOL)

    HOD

    PM) asphalt concrete. The specimens ... as poor materials selection and quality, design and construction lapses, climatic ... AN EXPERIMENTAL STUDY ON THE USE OF POLYPROPYLENE WASTE IN BITUMINOUS MIX. H. S. Otuoze & A. A. ...

  1. Management of the used ion-exchangers contaminated with C-14 generated by NPP Cernavoda

    International Nuclear Information System (INIS)

    Boteanu, O.; Valeca, M.; Arsene, C.

    2016-01-01

    For the conditioning of ion-exchangers generated from operation of Cernavoda NPP Unit 1, techniques of direct immobilization in cement, bitumen and organic polymers have been experimented. The selected process for conditioning of spent resins is the bituminization. The bituminization process consists of the incorporation in bitumen of the spent resin, at temperatures between 110 and 1200C, and the solidification of the mixture by cooling. The percentage of incorporated spent resin in bitumen is ranged from 40 to 50% dry resin. The advantages of bituminization are: the bitumen is insoluble in water, the bituminization installation is simple, the matrix is not cost expensive, the temperature process is low, bitumen is compatible with wastes having various compositions, and the volume of the final product is smaller. The main disadvantage is that bitumen is combustible, although not easily flammable, and, at high temperature, interaction between bitumen matrix and chemical components, might occur. (authors)

  2. Overlay design method based on visual pavement distress.

    Science.gov (United States)

    1978-01-01

    A method for designing the thickness of overlays for bituminous concrete pavements in Virginia is described. In this method the thickness is calculated by rating the amount and severity of observed pavement distress and determining the total accumula...

  3. 78 FR 43870 - Hydrogen Energy California's Integrated Gasification Combined Cycle Project; Preliminary Staff...

    Science.gov (United States)

    2013-07-22

    ... western sub-bituminous coal and 25 percent petroleum coke (petcoke) into a synthesis gas (syngas). The... project could generate urea, ammonia, and perhaps other nitrogenous compounds for sale. The project's urea...

  4. 75 FR 70950 - Request for Certification of Compliance-Rural Industrialization Loan and Grant Program

    Science.gov (United States)

    2010-11-19

    ... enterprise is: 212112 Bituminous Coal Underground Mining. DATES: All interested parties may submit comments... buildings, purchase mining equipment, and to create working capital. The office and mine are to be located...

  5. Performance oriented guidance for Mississippi chip seals - volume I.

    Science.gov (United States)

    2013-12-01

    A five year laboratory study was conducted to investigate near surface properties of flexible pavements in relation to : how they are affected by bituminous surface treatments. Chip seals and scrub seals (a specialized type of chip seal) : were the f...

  6. Simulation of one-dimensional heat transfer system based on the blended coal combustion

    Science.gov (United States)

    Jin, Y. G.; Li, W. B.; Cheng, Z. S.; Cheng, J. W.; liu, Y.

    2017-12-01

    In this paper, the supercritical boiler thermodynamic calculation model is studied. Three types of heat exchangers are proposed, namely furnace (total radiation type), semi-radiation and convection, and discussed. Two cases were simulated - mixing of two bituminous coals and mixing of a bituminous coal and lignite- order to analyze the performance on the flue gas side. The study shows that the influence of flue air leakage and gas distribution coefficient on the system.

  7. The Case of Coal Water Slurry Fuel for Industrial Use in Pakistan

    OpenAIRE

    Muhammad Irfan; Mohammad A. Irfan; Afzal Khan; Irfan Ullah; Noman Wazir

    2015-01-01

    This research presents the case for design and development of Coal Water Slurry (CWS) Plant for industrial use in Pakistan. After exclusive comparison between coal quality quantification for CWS it was found that Darra mines at Pakistan provide best coal for CWS. Highly volatile, A and B Bituminous coal and Sub-Bituminous coal is selected for making CWS because of its low Sulfur contents, Ash contents and high heating value through experimentation. The purpose of this research was to present ...

  8. Greenhouse gas emission factor development for coal-fired power plants in Korea

    International Nuclear Information System (INIS)

    Jeon, Eui-Chan; Myeong, Soojeong; Sa, Jae-Whan; Kim, Jinsu; Jeong, Jae-Hak

    2010-01-01

    Accurate estimation of greenhouse gas emissions is essential for developing an appropriate strategy to mitigate global warming. This study examined the characteristics of greenhouse gas emission from power plants, a major greenhouse gas source in Korea. The power plants examined use bituminous coal, anthracite, and sub-bituminous coal as fuel. The CO 2 concentration from power plants was measured using GC-FID with methanizer. The amount of carbon, hydrogen, and calorific values in the input fuel was measured using an elemental analyzer and calorimeter. For fuel analysis, CO 2 emission factors for anthracite, bituminous coal, and sub-bituminous coal were 108.9, 88.4, and 97.9 Mg/kJ, respectively. The emission factors developed in this study were compared with those for IPCC. The results showed that CO 2 emission was 10.8% higher for anthracite, 5.5% lower for bituminous coal, and 1.9% higher for sub-bituminous coal than the IPCC figures.

  9. Fiscal 1995 achievement report 1/2. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1995 nendo seika hokokusho 1/2. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. In the modification of facilities, oil product reforming facilities basic designs were prepared enabling the hydrogenation of coal oil after the liquefaction reaction process for reducing hetero compounds in coal oil in the NEDOL process. In the study of operation, pre-operation verification was accomplished under facilities cost performance exploring conditions for the pilot plant and, for the purpose of exploring optimum conditions for the NEDOL process, a 62-day and 25-day slurry injection operations were conducted using Tanito Harum coal and natural pyrite. In a 16-day operation for maintenance, data including mass balance were collected for the investigation of the initial reaction in liquefaction. The specimen sampling section of the high-temperature/high-pressure sampling device, which had been moved to the 3rd liquefaction reactor, was tentatively operated. In the solvent hydrogenation process, 2 hydrogenation reactors were connected in series and then operated for the verification of operationality. (NEDO)

  10. Fiscal 1994 achievement report 1/2. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1994 nendo seika hokokusho 1/2. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The operation of a 1t/d PSU (process support unit) was studied in the NEDOL coal liquefaction process. Modification was made, which involved the installation of a high-temperature/high-pressure sampling device for observing reaction and fluidity in the liquefaction reactor, a differential pressure measuring device, and a neutron attenuation-aided measuring device. Relative to coal injection, a 49.5-day and 49.3-day slurry injections were carried out using Tanito Harum coal, when impacts on the product yield and the operability of the unit were examined. A verification test was conducted for an improved hydrogenation catalyst, and liquefaction reactor characteristics were investigated. During a 19-day operation for the study of maintenance, newly installed equipment and devices were verified for function, and operating methods were probed into. In the survey of environments, characteristics were examined of the wastewater discharged from the Tanito Harum coal liquefaction process, and wastewater treatment methods were studied. The air, odor, and tar mist were examined with the PSU in operation, and the measured values were found to be below the management limits showing that its operation did not pose any problems relating to working environments. (NEDO)

  11. Viscoelastic behaviour of cold recycled asphalt mixes

    Science.gov (United States)

    Cizkova, Zuzana; Suda, Jan

    2017-09-01

    Behaviour of cold recycled mixes depends strongly on both the bituminous binder content (bituminous emulsion or foamed bitumen) and the hydraulic binder content (usually cement). In the case of cold recycled mixes rich in bitumen and with low hydraulic binder content, behaviour is close to the viscoelastic behaviour of traditional hot mix asphalt. With decreasing bituminous binder content together with increasing hydraulic binder content, mixes are characteristic with brittle behaviour, typical for concrete pavements or hydraulically bound layers. The behaviour of cold recycled mixes with low content of both types of binders is similar to behaviour of unbound materials. This paper is dedicated to analysing of the viscoelastic behaviour of the cold recycled mixes. Therefore, the tested mixes contained higher amount of the bituminous binder (both foamed bitumen and bituminous emulsion). The best way to characterize any viscoelastic material in a wide range of temperatures and frequencies is through the master curves. This paper includes interesting findings concerning the dependency of both parts of the complex modulus (elastic and viscous) on the testing frequency (which simulates the speed of heavy traffic passing) and on the testing temperature (which simulates the changing climate conditions a real pavement is subjected to).

  12. Methane de-NOX for Utility PC Boilers

    Energy Technology Data Exchange (ETDEWEB)

    Bruce Bryan; Joseph Rabovitser; Serguei Nester; Stan Wohadlo

    2005-03-31

    Large-scale combustion tests with caking bituminous coal was on hold this quarter mainly due to Riley's Commercial Burner Test Facility (CBTF) not having adequate weatherproofing to support operation under freezing conditions. The CBTF was secured and decommissioned for the winter season. CBTF bituminous coal tests shall continue to remain on hold now as a result of project funding limitations, however. No further modifications at the CBTF are planned until needed support is obtained. Activities this quarter have concentrated on finding additional support for the project. Currently, GTI has been granted a no-cost time extension through September 2005 and efforts to secure more support will continue in hopes that large-scale preheat caking bituminous combustion tests will be carried out as planned.

  13. Health risk assessment for a MWC ash utilization demonstration project

    International Nuclear Information System (INIS)

    Roffman, H.K.

    1992-01-01

    A Health Risk Assessment (HRA) was conducted for the proposed joint Hennepin County/Municipal Services Corporation (MSC) MSW Ash Utilization Demonstration Project, in which combined HERC ash was shipped to the MSC Pilot Plan near Atlanta, Georgia and used in the production of a synthetic aggregate. The synthetic aggregate, or TAP, will serve as a partial replacement for natural aggregates in a section of bituminous pavement that is proposed to be constructed on Pioneer Trail in the City of Corcoran, Minnesota. In this paper, the assessment compares the following three scenarios: a section of roadway paved using the MSC synthetic aggregate product (TAP) as a replacement for 30 percent of the natural aggregates used in bituminous pavement; a section of regular bituminous (asphalt) pavement; and a section of unpaved road currently in place at the site

  14. Intrusion resistant underground structure (IRUS) : design and operations

    International Nuclear Information System (INIS)

    Lange, B.A.

    1997-01-01

    The safety case for the IRUS low-level radioactive waste disposal facility is based on the fact that IRUS will contain three specific types of wastes only. The types of these wastes are baled wastes, bituminized incinerator ash, and bituminized reverse osmosis concentrate. IRUS will be a below-ground vault consisting of an open bottom reinforced-concrete structure (approximate dimensions 30m x 20m x 8m) with a reinforced-concrete roof. This paper covers the vault design and construction and operational features. 2 tabs

  15. Proceedings of Symposium on Energy Engineering in the 21st Century (SEE 2000). Volume Four

    Science.gov (United States)

    2000-01-13

    9.6%, respectively, based on the proximate analysis results of each paper. The heating value of the paper mixture is equivalent to that of the lignite ...Char A Bituminous 10-10 bars He + Lignite ° Bituminous 0 bar • » I bar He 600 700 Pyrolysis Temperature 800 0(< 900 1000...Mechanics, v. 2, pp.437-440, Allied Publishers Ltd, Chennai, India (1997). ^ 10 J. Mi, R.E. Luxton and G.J. Nathan, "The mean velocity field of a

  16. Intrusion resistant underground structure (IRUS) : design and operations

    Energy Technology Data Exchange (ETDEWEB)

    Lange, B.A. [Atomic Energy of Canada Ltd., Chalk River, ON (Canada)

    1997-12-31

    The safety case for the IRUS low-level radioactive waste disposal facility is based on the fact that IRUS will contain three specific types of wastes only. The types of these wastes are baled wastes, bituminized incinerator ash, and bituminized reverse osmosis concentrate. IRUS will be a below-ground vault consisting of an open bottom reinforced-concrete structure (approximate dimensions 30m x 20m x 8m) with a reinforced-concrete roof. This paper covers the vault design and construction and operational features. 2 tabs.

  17. Adsorption of Non-ionic Surface Active Agent on Fine Coal and Lignite

    OpenAIRE

    AKTAŞ, Zeki

    2014-01-01

    The adsorption of Triton X-100 in aqueous solution on the less than 53 \\mm size fractions of Tunçbilek lignite and Zonguldak bituminous coal was studied. The adsorption isotherms were formed for 5, 30 and 1,440 (equilibrium) minutes. The isotherms were evaluated using both Langmuir and Freundlich adsorption equations. Concentrations of the reagent in the monolayer after equilibrium adsorption were determined to be 8.17 and 7.27 \\mM/g coal for the lignite and bituminous coal using th...

  18. Routine Testing of Bitumen Binders

    Directory of Open Access Journals (Sweden)

    Holý Michal

    2017-12-01

    Full Text Available The quality of bituminous binders used in the construction and maintenance of road surfaces is currently assessed by empirical testing based on obtaining one value for specific boundary conditions, which were designed about 100 years ago. Basic empirical tests include the softening point and penetration, but the practice shows that these tests appear to be inadequate. The evaluation of changes of bitumen properties during the production and paving process of bituminous mixture is also important. The paper points out how the “traditional” tests as softening point and penetration and viscosity are sufficient to evaluate properties of bitumen binders.

  19. Routine Testing of Bitumen Binders

    Science.gov (United States)

    Holý, Michal; Remišová, Eva

    2017-12-01

    The quality of bituminous binders used in the construction and maintenance of road surfaces is currently assessed by empirical testing based on obtaining one value for specific boundary conditions, which were designed about 100 years ago. Basic empirical tests include the softening point and penetration, but the practice shows that these tests appear to be inadequate. The evaluation of changes of bitumen properties during the production and paving process of bituminous mixture is also important. The paper points out how the "traditional" tests as softening point and penetration and viscosity are sufficient to evaluate properties of bitumen binders.

  20. Near-Zero Emissions Oxy-Combustion Flue Gas Purification - Power Plant Performance

    Energy Technology Data Exchange (ETDEWEB)

    Andrew Seltzer; Zhen Fan

    2011-03-01

    A technical feasibility assessment was performed for retrofitting oxy-fuel technology to an existing power plant burning low sulfur PRB fuel and high sulfur bituminous fuel. The focus of this study was on the boiler/power generation island of a subcritical steam cycle power plant. The power plant performance in air and oxy-firing modes was estimated and modifications required for oxy-firing capabilities were identified. A 460 MWe (gross) reference subcritical PC power plant was modeled. The reference air-fired plant has a boiler efficiency (PRB/Bituminous) of 86.7%/89.3% and a plant net efficiency of 35.8/36.7%. Net efficiency for oxy-fuel firing including ASU/CPU duty is 25.6%/26.6% (PRB/Bituminous). The oxy-fuel flue gas recirculation flow to the boiler is 68%/72% (PRB/bituminous) of the flue gas (average O{sub 2} in feed gas is 27.4%/26.4%v (PRB/bituminous)). Maximum increase in tube wall temperature is less than 10ºF for oxy-fuel firing. For oxy-fuel firing, ammonia injected to the SCR was shut-off and the FGD is applied to remove SOx from the recycled primary gas stream and a portion of the SOx from the secondary stream for the high sulfur bituminous coal. Based on CFD simulations it was determined that at the furnace outlet compared to air-firing, SO{sub 3}/SO{sub 2} mole ratio is about the same, NOx ppmv level is about the same for PRB-firing and 2.5 times for bituminous-firing due to shutting off the OFA, and CO mole fraction is approximately double. A conceptual level cost estimate was performed for the incremental equipment and installation cost of the oxyfuel retrofit in the boiler island and steam system. The cost of the retrofit is estimated to be approximately 81 M$ for PRB low sulfur fuel and 84 M$ for bituminous high sulfur fuel.

  1. Radioactivity of combustion residues from coal-fired power stations

    International Nuclear Information System (INIS)

    Vom Berg, W.; Puch, K.H.

    1996-01-01

    Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

  2. Development of clean coal and clean soil technologies using advanced agglomeration techniques

    International Nuclear Information System (INIS)

    Ignasiak, B.; Ignasiak, T.; Szymocha, K.

    1990-01-01

    Three major topics are discussed in this report: (1) Upgrading of Low Rank Coals by the Agflotherm Process. Test data, procedures, equipment, etc., are described for co-upgrading of subbituminous coals and heavy oil; (2) Upgrading of Bituminous Coals by the Agflotherm Process. Experimental procedures and data, bench and pilot scale equipments, etc., for beneficiating bituminous coals are described; (3) Soil Clean-up and Hydrocarbon Waste Treatment Process. Batch and pilot plant tests are described for soil contaminated by tar refuse from manufactured gas plant sites. (VC)

  3. Health and safety plan for the removal action at the former YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-04-28

    This health and safety plan sets forth the requirements and procedures to protect the personnel involved in the Lead Source Removal Project at the Former YS-86O Firing Ranges. This project will be conducted in a manner that ensures the protection of the safety and health of workers, the public, and the environment. The purpose of this removal action is to address lead contaminated soil and reduce a potential risk to human health and the environment. This site is an operable unit within the Upper East Fork Poplar Creek watershed. The removal action will contribute to early source actions within the watershed. The project will accomplish this through the removal of lead-contaminated soil in the target areas of the two small arms firing ranges. This plan covers the removal actions at the Former YS-86O Firing Ranges. These actions involve the excavation of lead-contaminated soils, the removal of the concrete trench and macadam (asphalt) paths, verification/confirmation sampling, grading and revegetation. The primary hazards include temperature extremes, equipment operation, noise, potential lead exposure, uneven and slippery working surfaces, and insects.

  4. Color Maintenance of LEDs in Laboratory and Field Applications

    Energy Technology Data Exchange (ETDEWEB)

    Royer, Michael P.; Tuttle, Ralph; Rosenfeld, Scott M.; Miller, Naomi J.

    2013-09-30

    Synopsis: To date, consideration for parametric failure of LED products has largely been focused on lumen maintenance. However, color shift is a cause of early failure for some products, and is especially important to consider in certain applications, like museums, where visual appearance is critical. Example data collected by the GATEWAY program for LED lamps installed in museums shows that many have changed color beyond a reasonable tolerance well before their rated lifetime was reached, necessitating replacement. Similar data collected by the CALiPER program between 2008 and 2010 reveals that many early products shifted beyond acceptable tolerances in as little as a few thousand hours. In contrast, data from the L Prize program illustrates that commercially available LED products can have exemplary color stability that is unmatched by traditional light sources. Beyond presenting data from the aforementioned DOE programs, this report discusses the metrics used for communicating color shift—namely MacAdam ellipses and Δu'v'—as well as providing guidance for end users on how to monitor color shift and what to look for in manufacturer warranties. Also included are descriptions of the physical changes that have been documented as leading to color shift in some example types of LED packages. As with complete products, the data presented herein for LED packages shows that a wide variety of products are available; in order for specifiers and consumers to make educated choices, more detailed and standardized information should be made available.

  5. Development of New Correlation and Assessment of Correlations for Two-Phase Pressure Drop in Rectangular Microchannels

    International Nuclear Information System (INIS)

    Choi, Chi Woong; Yu, Dong In; Kim, Moo Hwan

    2010-01-01

    There are two kinds of models in two-phase pressured drop; homogeneous flow model and separated flow model. Many previous researchers have developed correlations for two-phase pressure drop in a microchannel. Most correlations were modified Lockhart and Martinelli's correlation, which was based on the separated flow model. In this study, experiments for adiabatic liquid water and nitrogen gas flow in rectangular microchannels were conducted to investigate two-phase pressure drop in the rectangular microchannels. Two-phase frictional pressure drop in the rectangular microchannels is highly related with flow regime. Homogeneous model with six two-phase viscosity models: Owen(21)'s, MacAdams(22)'s, Cicchitti et al.(23)'s, Dukler et al.(24)'s, Beattie and Whalley(25)'s, Lin et al.(26)'s models and six separated flow models: Lockhart and Martinelli(27)'s, Chisholm(31)'s, Zhang et al.(15)'s, Lee and Lee(5)'s, Moriyama and Inue(4)'s, Qu and Mudawar(8)'s models were assessed with our experimental data. The best two-phase viscosity model is Beattie and Whalley's model. The best separated flow model is Qu and Mudawar's correlation. Flow regime dependency in both homogeneous and separated flow models was observed. Therefore, new flow pattern based correlations for both homogeneous and separated flow models were individually proposed

  6. Quality assurance project plan for the removal action at the former YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1998-03-01

    This quality assurance project plan defines project organization and roles of responsibility, sampling and field procedures, sample documentation and chain-of-custody protocols, equipment calibration, analytical procedures, data reduction and validation, and internal quality control procedures for the former YS-860 Firing Ranges removal action at the Oak Ridge Y-12 Plant. The ENTECH Team will maintain the highest standards to ensure strict compliance with this plan. Implementation of this plan will include consideration of the technical, as well as administrative, aspects of activities affecting quality. Plan implementation is based on the premise that quality controls selected for each element of work are consistent with the risk, importance, and health and safety considerations of performing the work. The purpose of this removal action is to address lead-contaminated soil and reduce a potential risk to human health and the environment. This site is an operable unit within the Upper East Fork Poplar Creek watershed. The removal action will contribute to early source actions within the watershed. The project will accomplish this through the removal of lead-contaminated soil in the target areas of two small arms firing ranges. This plan covers the removal action at the former YS-86O Firing Ranges. These actions involve the excavation of lead-contaminated soils, the removal of the concrete trench and macadam (asphalt) paths, verification sampling, grading, and revegetation

  7. De-entangling colorfulness and fidelity for a complete statistical description of color quality.

    Science.gov (United States)

    Quintero, Jesús M; Hunt, Charles E; Carreras, Josep

    2012-12-01

    In this Letter, the main attributes known to affect color quality are treated statistically over a set of 118 spectra representing the current mainstream lighting technology. The color rendering index (CRI) is used to assess color fidelity while colorfulness is used to complement CRI-R(a), supported by the growing evidence that assessment of light spectra cannot overlook color preference inputs. Colorfulness is evaluated by our optimal color (O(c)) index, through a code that computes the (MacAdam) theoretical maximum volumetric gamut of objects under a given illuminant for all the spectra in our database. Pearson correlation coefficients for CRI-R(a), the (Y. Ohno's) color quality scale (CQS) and O(c) show a high correlation (0.950) between CRI-R(a) and CQS-Q(a), while O(c) shows the lowest correlation (0.577) with CRI-R(a), meaning that O(c) represents the best complement to CRI-R(a) and Q(a) for an in-depth study of color quality.

  8. Health and safety plan for the removal action at the former YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1998-01-01

    This health and safety plan sets forth the requirements and procedures to protect the personnel involved in the Lead Source Removal Project at the Former YS-86O Firing Ranges. This project will be conducted in a manner that ensures the protection of the safety and health of workers, the public, and the environment. The purpose of this removal action is to address lead contaminated soil and reduce a potential risk to human health and the environment. This site is an operable unit within the Upper East Fork Poplar Creek watershed. The removal action will contribute to early source actions within the watershed. The project will accomplish this through the removal of lead-contaminated soil in the target areas of the two small arms firing ranges. This plan covers the removal actions at the Former YS-86O Firing Ranges. These actions involve the excavation of lead-contaminated soils, the removal of the concrete trench and macadam (asphalt) paths, verification/confirmation sampling, grading and revegetation. The primary hazards include temperature extremes, equipment operation, noise, potential lead exposure, uneven and slippery working surfaces, and insects

  9. Petrographic and mineral characterization of Balkan coals and their solid waste products from coal preparation

    International Nuclear Information System (INIS)

    Yossifova, M.

    1995-01-01

    This paper is part of a complex petrographic, mineralogical and chemical investigation on Balkan bituminous coals and their solid waste products from coal preparation. The petrographic and phase-mineralogical composition in ten composite samples and four water extracts have been studied by optical microscopy, scanning electron microscopy and X-ray diffraction. 4 refs., 4 tabs

  10. METHANE de-NOX for Utility PC Boilers

    Energy Technology Data Exchange (ETDEWEB)

    Bruce Bryan; Joseph Rabovitser; Serguei Nester; Stan Wohadlo

    2004-09-30

    Large-scale PRB testing during the current quarter was cut short due to the inability of the coal mill to meet the 85 MMBtu/h design firing rate. The project was therefore redirected toward design, installation and testing of the 85-million Btu/h preheater for bituminous coal. Based on extensive pilot-scale testing completed earlier in the project, 2-D modeling and preliminary design activities were started based on the use of staged, annular protective air films to control temperature and prevent deposition on the preheater walls. A total of 14 2-D modeling cases were completed for the modified preheater for bituminous coal. The preheater concept modeled was based on an expanding preheater chamber where the diameter of the chamber is increased in steps along its length and annular cooling/protective air is introduced at each step. A process flow diagram for the bituminous coal preheating system and a preliminary preheater design drawing were developed based on the modeling results. A project schedule to complete design, installation and testing of the 85 MMBtu/h bituminous coal preheating system before the end of December was also developed.

  11. CO2 capture from power plants. Part I : A parametric study of the technical performance based on monoethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, M. R. M.; Schneiders, L. H. J.; Niederer, J. P. M.; Feron, P. H. M.; Versteeg, G. F.

    Capture and storage of CO2 from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO2 capture process from flue gas of a 600 MWe bituminous coal fired power plant, based

  12. 40 CFR 52.2054 - Control of asphalt paving material.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control of asphalt paving material. 52... asphalt paving material. (a) Notwithstanding any provisions to the contrary in the Pennsylvania... bituminous asphalt paving material used shall be cutback asphalt; and (2) No more than 2,615,000 gallons of...

  13. Uruguay minerals fuels

    International Nuclear Information System (INIS)

    Goso, H.

    1967-01-01

    In this report the bases for the development of the necessary works of prospection are exposed on mineral fuels of Uruguay. We have taken the set from: coal, lutitas bituminous, uranium, petroleum and disturbs. In all the cases we have talked about to the present state of the knowledge and to the works that we considered necessary to develop in each case

  14. Co-combustion of tannery sludge in a commercial circulating fluidized bed boiler.

    Science.gov (United States)

    Dong, Hao; Jiang, Xuguang; Lv, Guojun; Chi, Yong; Yan, Jianhua

    2015-12-01

    Co-combusting hazardous wastes in existing fluidized bed combustors is an alternative to hazardous waste treatment facilities, in shortage in China. Tannery sludge is a kind of hazardous waste, considered fit for co-combusting with coal in fluidized bedboilers. In this work, co-combustion tests of tannery sludge and bituminous coal were conducted in a power plant in Jiaxing, Zhejiang province. Before that, the combustion behavior of tannery sludge and bituminous were studied by thermogravimetric analysis. Tannery sludge presented higher reactivity than bituminous coal. During the co-combustion tests, the emissions of harmful gases were monitored. The results showed that the pollutant emissions met the Chinese standard except for NOx. The Concentrations of seven trace elements (As, Cr, Cd, Ni, Cu, Pb, Mn) in three exit ash flows (bottom ash in bed, fly ash in filter, and submicrometer aerosol in flue gas) were analyzed. The results of mono-combustion of bituminous coal were compared with those of co-combustion with tannery sludge. It was found that chromium enriched in fly ash. At last, the leachability of fly ash and bottom ash was analyzed. The results showed that most species were almost equal to or below the limits except for As in bottom ashes and Cr in the fly ash of co-combustion test. The concentrations of Cr in leachates of co-combustion ashes are markedly higher than that of coal mono-combustion ashes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. 78 FR 52973 - ICG Knott County, LLC, a Subsidiary of ICG, Inc., a Subsidiary of Arch Coal, Inc.; Including On...

    Science.gov (United States)

    2013-08-27

    ... Regarding Application for Reconsideration for the workers and former workers of ICG Knott County, LLC, a... Officer, a mis- interpretation of facts or of the law justified reconsideration of the decision. The... increased use of natural gas instead of bituminous coal by customers of the subject firm and customers of...

  16. Best practice: bitumen-emulsion and foamed bitumen materials laboratory processing

    CSIR Research Space (South Africa)

    Kekwick, SV

    2005-07-01

    Full Text Available of these materials, which can include both active and inactive fillers such as lime, cement, fly ash, etc., as well as the bituminous binder and parent material. The complexities of the various chemical reactions and interactions that will occur during the treatment...

  17. Technical report on NEDO-conducted Western US steam coal (for power generation and boiler) survey

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    The New Energy and Industrial Technology Development Organization (NEDO) conducted studies covering Wyoming, Utah, Colorado, New Mexico, and North Dakota, all in the West. Illinois and Gulf-Texas are also included. The bituminous coal of Utah and Colorado is given the highest priority as coal to be exported to Japan. It is feared, however, that the price of the bituminous coal from these areas may soar if demand increases. As for sub-bituminous coal, its price is far more stable because its reserves are basically limitless. The sub-bituminous coal, however, is not expected to be imported to Japan in the very near future because it is low in calorific power and fails to meet the conditions prerequisite to Japan's boiler fuel. Illinois can receive large orders but its coal contains more sulfur than the Western coal and a longer distance has to be covered for its transportation. As for transportation to the West Cost, freight cars are available and the port capacity can be enlarged dependent on the magnitude of demand for coal. Loading a deep draft bulk ship off shore with coarse coal slurry by pipeline is an attractive scheme. (NEDO)

  18. A toadfish (Batrachoidiformes) from the Oligocene of the Eastern Carpathians (Piatra Neamt, Romania)

    Czech Academy of Sciences Publication Activity Database

    Přikryl, Tomáš; Grădianu, I.; Georgescu, V.; Carnevale, G.

    2018-01-01

    Roč. 287, č. 2 (2018), s. 241-248 ISSN 0077-7749 R&D Projects: GA ČR(CZ) GA16-21523S Institutional support: RVO:67985831 Keywords : Batrachoidiformes * toadfish * Bituminous Marls Formation * Eastern Carpathians * Oligocene Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.777, year: 2016

  19. the optimum value index in the yield of carbon through continuous

    African Journals Online (AJOL)

    Dr Obe

    In this work, a brief summary of the production of pitch from coal tar and petroleum residues has been ... employed in the construction of rocket motors for re-entry ... Residue. 61. Smith et al, in bituminous materials. 2.3 Petroleum pitch: Petroleum pitch is a readily available product, which can be obtained from the bottom of.

  20. Evaluation of open-graded friction course mixture : technical assistance report.

    Science.gov (United States)

    2004-10-01

    Open-graded friction course (OGFC) is a porous, gap-graded, predominantly single size aggregate bituminous mixture that contains a high percentage of air voids. The high air void content and the open structure of this mix promote the effective draina...

  1. WaiGao Qiao: taking supercritical technology to new heights

    Energy Technology Data Exchange (ETDEWEB)

    Kessel, W.; Weiss, G.; Kawa, P. [Alstom, Stuttgart (Germany)

    2006-06-15

    In their first two years of commercial life the two supercritical boilers of Wai Gao Qiao Phase II, at 900 MWe each the largest operating coal fired units in China and the largest tangentially fired bituminous coal fired boilers in the world have performed reliably and efficiently. 11 figs., 1 tab.

  2. Translations on Eastern Europe, Political, Sociological, and Military Affairs, Number 1496.

    Science.gov (United States)

    1978-01-19

    34 And this not only in Europe: in Egypt, India and elsewhere in the world, August of 1968 was a lesson for the politicians, who saw what it meant to...progressive technologies. d) Insuring and rationally managing fuels and energy by utilizing brown coal, lignite and bituminous shales reserves, by

  3. The Economy of Romania: How it Compares to Other Centrally-Planned Economies in Eastern Europe.

    Science.gov (United States)

    1984-06-01

    Argen- 20 percent tina, Brazil, Egypt, Greece, India , Iran, Iraq, Israel, Jordan, Lebanon, Libya, Portugal, Spain, Syria, Turkey) 109 10 9...Land, Forestry Area Plate 2 Natural Resources A = Oil S = Natural Gas S = Coal (Pitcoal, Lignite , Anthracite, and Bituminous) Plate 3 Distribution of

  4. Radium contamination in the Nizzana-1 water well, Negev Desert, Israel

    International Nuclear Information System (INIS)

    Minster, T.; Ilani, S.; Kronfeld, J.; Even, O.; Godfrey-Smith, D.I.

    2004-01-01

    In a search for fresh groundwater reserves in the northwestern Negev Desert of Israel, the Nizzana-1 water well drilled into the Judea Group aquifer encountered water that exhibits an anomalously high 226 Ra activity of 2.4 Bq/l, along with 133 Bq/l 222 Rn. The exploited well water is a mixture of the original Judea Group aquifer water and the underlying more saline artesian water of the Kurnub Group (or Nubian Sandstone) aquifer that is currently intruding via faults. Both aquifers elsewhere contain intrinsically low radioactivity. A study of the sedimentary sequence transected by the borehole revealed that much of the bituminous sequence of the Mount Scopus Group of Upper Cretaceous age is substantially depleted in 226 Ra. During its ascent, the Nubian Sandstone water flushes the moderately uranium enriched bituminous sediments, selectively leaching radium and/or receiving alpha-recoil additions of radium. These bituminous chalks and marls are regionally widespread. It is thus suggested that radium should be monitored where faulting allows for inter-aquiferial connections across uranium enriched bituminous sections

  5. Behaviour of six sulphided iron hydroliquefaction catalysts

    International Nuclear Information System (INIS)

    Cook, P.S.; Cashion, J.D.; Bell, A.P.

    1994-01-01

    Five iron ore samples and a synthetic magnetite were added to Wandoan bituminous coal as hydroliquefaction catalysts. Catalyst transformations after sulphiding and after subsequent hydrogenation were analysed. The conversion efficiency increased with decreasing particle size or increased crystallographic disorder and showed that different catalytic mechanisms operate in the hydroliquefaction of brown and black coals. (orig.)

  6. Untitled

    African Journals Online (AJOL)

    tion studies of the origins of coal. This paper reports an investigation carried out on four. Nigerian sub-bituminous coals (Onyeama,. Okpara, Okaba and Owukpa) using simple solvents. The urea-adducts obtained from the extracted and fractionated materials were analysed by gas chro- matography. EXERMENTAL.

  7. major oxides and trace element distributions in coal and coaly shale ...

    African Journals Online (AJOL)

    Admin

    Elemental distributions in nine (9) sub-bituminous coal and four coaly shale samples from the Anambra Basin, south- ... Coal occurs also in other sedimentary formation in Nigeria, such as in Lafia-Obi, Lamja, Gombe, Bauchi, Pindiga among others. Most trace elements in coal are ..... Journal of Fuel Chemistry and.

  8. 26 CFR 1.404(c)-1 - Certain negotiated plans; effect of section 404(c).

    Science.gov (United States)

    2010-04-01

    ... TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Pension, Profit-Sharing, Stock Bonus Plans, Etc... such an agreement in the bituminous coal industry, a similar trust established about the same time in the anthracite coal industry would be covered by this provision. (c) If any such trust becomes...

  9. 21 CFR 358.703 - Definitions.

    Science.gov (United States)

    2010-04-01

    ... distillation of bituminous coal at temperatures in the range of 900 °C to 1,100 °C. It may be further processed using either extraction with alcohol and suitable dispersing agents and maceration times or fractional distillation with or without the use of suitable organic solvents. (b) Dandruff. A condition involving an...

  10. Untitled

    African Journals Online (AJOL)

    2004-04-30

    Apr 30, 2004 ... "Department of Geology and > Centre for Energy Research and Development,. Obafemi Awolowo ... Gamma ray spectrometric and Energy-dispersive X-ray fluorescence analyses were carried out on samples of bituminous sand deposits of ..... Geothermal gradients, heat flow and hydrocarbon recovery, In: ...

  11. Model based decision support for planning of road maintenance

    NARCIS (Netherlands)

    van Harten, Aart; Worm, J.M.; Worm, J.M.

    1996-01-01

    In this article we describe a Decision Support Model, based on Operational Research methods, for the multi-period planning of maintenance of bituminous pavements. This model is a tool for the road manager to assist in generating an optimal maintenance plan for a road. Optimal means: minimising the

  12. Molecular characterization of flash pyrolysates of two Carboniferous coals and their constituting maceral fractions

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Hartgers, W.A.; Ling, Y.; Leeuw, J.W. de; Dyrckacz, G.

    1994-01-01

    Two high-volatile bituminous Upper Carboniferous coals from the Argonne Premium Coal Set and their constituting liptinite, vitrinite, and inertinite fractions, obtained by density gradient centrifugation (DGC), were characterized by Curie point pyrolysis-gas chromatography-mass spectrometry. A

  13. System for transport and removal of radioactive wastes

    International Nuclear Information System (INIS)

    Kucharik, D.

    1985-01-01

    A detailed description is given of basic components of the equipment for removing radioactive concentrates from storage tanks in the V-1 nuclear power plant and their transport to the bituminization line. The system was tried in operation with actual radioactive wastes and meets the demands placed on the continuous operation of the bituminization line with regard to the firmly adjustable parameters of the bituminization process. This is achieved by homogenization of the concentrate in the storage tank by means of an in-built system and recirculation, of an own pumping system and of heating the concentrate in a special steam-heated heat exchanger. Transport containers are filled using a remote controlled filling head which is suspended on a rotary arm whose rotation as well as the application of the head to the container are provided with a pneumatic cylinder. A similar device serves the remote controlled emptying of containers. PC-55 containers mounted on trucks are used for transporting radioactive wastes to the bituminization line. The 55 mm thick shielding of containers ensures that the maximum exposure rate is 5 mR/h at a distance of 2 metres from the containers. (Z.M.)

  14. De lichttechnische eigenschappen van lichtgekleurde wegoppervlakken : artikel Wegen 56 10: 803-824 t/m 803-325.

    NARCIS (Netherlands)

    Schreuder, D.A.

    1982-01-01

    Cement concrete road surfaces have, because of their light colour, a double luminance yield as compared with bituminous roads. Savings in electricity amount to at least 20% in illumination costs or 5-10% of total maintenance costs. Light colour improves visibility at night. Road markings in white

  15. De lichttechnische eigenschappen van lichtgekleurde wegoppervlakken.

    NARCIS (Netherlands)

    Schreuder, D.A.

    1982-01-01

    Cement concretes road surface have, because of their light colour, a double luminance yield as compared with bituminous roads. Savings in electricity amount to at least 20% in illumination costs or 5-10% of total maintenance costs. Light colour improves visibility at night. Road markings in white

  16. Transuranic contaminated waste form characterization and data base

    International Nuclear Information System (INIS)

    Kniazewycz, B.G.; McArthur, W.C.

    1980-07-01

    This volume contains appendices A to F. The properties of transuranium (TRU) radionuclides are described. Immobilization of TRU wastes by bituminization, urea-formaldehyde polymers, and cements is discussed. Research programs at DOE facilities engaged in TRU waste characterization and management studies are described

  17. A review of the timing of coalification in the light of coal seam erosion, clastic dykes and coal clasts

    Czech Academy of Sciences Publication Activity Database

    Pešek, J.; Sýkorová, Ivana

    2006-01-01

    Roč. 66, 1-2 (2006), s. 13-34 ISSN 0166-5162 R&D Projects: GA AV ČR IAA3111103 Institutional research plan: CEZ:AV0Z30460519 Keywords : timming of coalification * bituminous coal seam * erosion of coal seams Subject RIV: DD - Geochemistry Impact factor: 1.667, year: 2006

  18. Download this PDF file

    African Journals Online (AJOL)

    rather cheaper means of stabilizing lateritic soils that has become very important for the construction industry. The soil samples were subjected to ... in road construction had been in practice since the. Roman times, . . . . . . Stabilization is ... This is also known as oil-sands or bituminous sands, contain oil impregnated rocks ...

  19. 76 FR 77502 - Intent To Prepare a Draft Environmental Impact Statement Regarding the Wolfpen Knob Development...

    Science.gov (United States)

    2011-12-13

    ... construction of the proposed Mason Dixon Mining Complex. The Corps will prepare the EIS in accordance with the... applicant, the Wolfpen Knob Development Company, is to extract bituminous coal from the Pittsburgh coal seam... preparation plant and dust control at the deep mine, preparation plant, and associated haul roads. A railroad...

  20. Full-Scale Accelerated Pavement Testing of Warm-Mix Asphalt (WMA) for Airfield Pavements

    Science.gov (United States)

    2014-01-01

    Rushing Geotechnical and Structures Laboratory US Army Engineer Research and Development Center 3909 Halls Ferry Road Vicksburg, MS 39180-6199...Table 1. Foundation layer soil properties as constructed . ...................................................................... 7  Table 2. WMA...during production of bituminous paving materials. In recent years, warm-mix asphalt (WMA) has replaced HMA for many paving projects. WMA is a general

  1. Integrated evolution of the medium power CANDU{sup MD} reactors; Evolution integree des reacteurs CANDU{sup MD} de moyenne puissance

    Energy Technology Data Exchange (ETDEWEB)

    Nuzzo, F. [AECL Accelerators, Kanata, ON (Canada)

    2002-07-01

    The aim of this document is the main improvements of the CANDU reactors in the economic, safety and performance domains. The presentation proposes also other applications as the hydrogen production, the freshening of water sea and the bituminous sands exploitation. (A.L.B.)

  2. 77 FR 33420 - Certain Activated Carbon From the People's Republic of China: Final Results of Expedited Sunset...

    Science.gov (United States)

    2012-06-06

    ... China (``PRC'') pursuant to section 751(c) of the Tariff Act of 1930, as amended (``the Act''). On the... steam various materials containing carbon, including but not limited to coal (including bituminous... Harmonized Tariff Schedule of the United States (``HTSUS'') subheading 3802.10.00. Although the HTSUS...

  3. 75 FR 70208 - Certain Activated Carbon From the People's Republic of China: Final Results and Partial...

    Science.gov (United States)

    2010-11-17

    ... steam various materials containing carbon, including but not limited to coal (including bituminous... Harmonized Tariff Schedule of the United States (``HTSUS'') subheading 3802.10.00. Although the HTSUS... the Tariff Act of 1930, as amended (``Act''), and preliminarily found that Jacobi has absorbed...

  4. 77 FR 55808 - Certain Preserved Mushrooms From the People's Republic of China: Final Results of Antidumping...

    Science.gov (United States)

    2012-09-11

    ... the Harmonized Tariff Schedule of the United States (HTSUS). Although the HTSUS subheadings are.... (2) For Blue Field, we revised our calculation of the surrogate value for coal to include bituminous coal and corrected a conversion error in the calculation of that surrogate value.\\13\\ \\13\\ See Id. at 2...

  5. 75 FR 981 - Certain Activated Carbon From the People's Republic of China: Notice of Rescission of Changed...

    Science.gov (United States)

    2010-01-07

    ...(b)(1) and 782(h)(2) of the Tariff Act of 1930, as amended (``the Act''), with respect to the same..., including but not limited to coal (including bituminous, lignite, and anthracite), wood, coconut shells... order are currently classifiable under the Harmonized Tariff Schedule of the United States (``HTSUS...

  6. 77 FR 76871 - Approval and Promulgation of Implementation Plans; State of Colorado; Regional Haze State...

    Science.gov (United States)

    2012-12-31

    ... to a number of different fuels. The State determined that Units 4 and 5 are not capable of burning... average annual emission rates that Colorado used for cost calculations with 30- day rolling average... based on the primary type of coal burned there, which is sub-bituminous. EPA should establish the...

  7. Properties and long-term behaviour of bitumen and radioactive waste-bitumen mixtures

    International Nuclear Information System (INIS)

    Eschrich, H.

    1980-10-01

    Part I represents a survey of the properties and the long-term behaviour of pure bitumens and mixtures of bitumens with radioactive reactor and reprocessing wastes. This survey includes information on the origin, amounts, and composition of the various wastes considered for bituminization and the different waste bituminization techniques used. The influence of various factors on the quality of waste-bitumen products and on the radiological safety during transport, short- and long-term storage of the final products is described. Special consideration is given to the most important safety relevant factors associated to the use of bitumen as matrix material for radioactive wastes, such as leach-resistance, radiolysis, chemical and mechanical stability, combustibility, and microbial attack. Part II consists of a comprehensive bibliography on the bituminization of radioactive wastes, giving about 300 references to literature published from the beginning of the use of bitumen in radioactive waste management in 1960 until the beginning of 1979. Methods for the quality control of bituminous materials and some useful data are given in an annex. (author)

  8. Transuranic contaminated waste form characterization and data base

    Energy Technology Data Exchange (ETDEWEB)

    Kniazewycz, B.G.; McArthur, W.C.

    1980-07-01

    This volume contains appendices A to F. The properties of transuranium (TRU) radionuclides are described. Immobilization of TRU wastes by bituminization, urea-formaldehyde polymers, and cements is discussed. Research programs at DOE facilities engaged in TRU waste characterization and management studies are described.

  9. Development of non-petroleum-based binders for use in flexible pavements - phase II.

    Science.gov (United States)

    2015-10-01

    Bio-binders can be utilized as asphalt modifiers, extenders, and replacements for conventional asphalt in bituminous binders. : From the rheology results of Phase I of this project, it was found that the bio-binders tested had good performance, simil...

  10. Quartz in ash, and air in a high lung cancer incidence area in China

    NARCIS (Netherlands)

    Downward, George S|info:eu-repo/dai/nl/412435667; Hu, Wei; Rothman, Nat; Reiss, Boris|info:eu-repo/dai/nl/314119205; Tromp, Peter; Wu, Guoping; Wei, Fusheng; Xu, Jun; Seow, Wei Jie; Chapman, Robert S.; Lan, Qing; Vermeulen, Roel|info:eu-repo/dai/nl/216532620

    Exposure to crystalline silica (quartz) has been implicated as a potential cause of the high lung cancer rates in the neighbouring counties of Xuanwei and Fuyuan, China, where the domestic combustion of locally sourced "smoky" coal (a bituminous coal) is responsible for some of the highest lung

  11. Using bamboo (Bambusa vulgaris) as a field drainage material in ...

    African Journals Online (AJOL)

    user

    shaped ceramic tile, circular clay tile, concrete tile, bituminized fibre perforated pipe, perforated smooth plastic pipe to corrugated plastic pipe. Currently, corrugated pipes are frequently used, although clay and concrete pipes are still being used as well. The use of drainage pipes made of various assorted materials is.

  12. Charakterizace produktů pyrolýzy uhlí s přídavkem směsných plastů

    Czech Academy of Sciences Publication Activity Database

    Havelcová, Martina; Bičáková, Olga; Sýkorová, Ivana; Melegy, A.

    2015-01-01

    Roč. 7, č. 1 (2015), s. 1-6 ISSN 1804-2058 Institutional support: RVO:67985891 Keywords : pyrolysis * sub-bituminous coal * mixed plastic wastes Subject RIV: DM - Solid Waste and Recycling http://paliva.vscht.cz/cz/archiv-clanku/detail/26

  13. Cool products for building envelope - Part II: Experimental and numerical evaluation of thermal performances

    NARCIS (Netherlands)

    Revel, G.M.; Martarelli, M.; Emiliani, M.; Celotti, L.; Nadalini, R.; Ferrari, A.D.; Hermanns, S.; Beckers, E.

    2014-01-01

    Cool materials have a large potential as cost-effective solution for reducing cooling energy consumption in hot summer and mild winter regions like Mediterranean countries. A previous paper has described in detail the development of cool coloured ceramic tiles, acrylic paints and bituminous

  14. An assessment of health implications of natural radioactivity in the ...

    African Journals Online (AJOL)

    Gamma ray spectrometric and Energy-dispersive X-ray fluorescence analyses were carried out on samples of bituminous sand deposits of Ondo State. The objectives were to determine the presence and level of radioactivity; assess the impact of radioactivity on the environment and provide a geochemical baseline data for ...

  15. Production and characterization of activated carbon from a ...

    African Journals Online (AJOL)

    In this study, the use of a bituminous coal for the production of activated carbons with chemical activation was investigated. The effects of process variables such as chemical reagents, activation temperature, impregnation ratio and carbonization temperature were investigated to optimize these parameters. The resultant ...

  16. NO Reduction over Biomass and Coal Char during Simultaneous Combustion

    DEFF Research Database (Denmark)

    Zhao, Ke; Glarborg, Peter; Jensen, Anker Degn

    2013-01-01

    This paper reports an experimental study of NO reduction over chars of straw, bark, bituminous coal, and lignite. The experiments were performed in a fixed bed reactor in the temperature range 850–1150 °C. The chars were generated by in situ pyrolysis at the reaction temperature to minimize further...

  17. Heterogeneity in coal composition and implications for lung cancer risk in Xuanwei and Fuyuan counties, China

    NARCIS (Netherlands)

    Downward, George S.|info:eu-repo/dai/nl/412435667; Hu, Wei; Large, David; Veld, Harry; Xu, Jun; Reiss, Boris|info:eu-repo/dai/nl/314119205; Wu, Guoping; Wei, Fusheng; Chapman, Robert S.; Rothman, Nat; Qing, Lan; Vermeulen, Roel|info:eu-repo/dai/nl/216532620

    2014-01-01

    Background: Xuanwei and Fuyuan counties in Yunnan Province, China have among the highest lung cancer rates in the country. This has been associated with the domestic combustion of bituminous coal (referred to as "smoky" coal). Additionally, significant geographical variation in cancer rates among

  18. A brief petrographic review on Nigerian coal resources

    International Nuclear Information System (INIS)

    Obaje, N. G.; Abaa, S. I.; Najime, T.; Suh, C. E.

    2000-01-01

    The coal resources of Nigeria are located mainly within the Benue Trough. In the lower Benue, subbituminous coals occur within the Maastrichtian Mamu Formation. High - volatile bituminous coals are found within the Turonian - Santonian Awgu Formation in the middle Benue while the upper Benue contains lignites and sub-bituminous coals in the Maastrichtian Gombe Sandstone Formation. Maceral analyses show that himinite dominates in the petrographic composition of the lower and upper Benue Trough coals with vitrinite reflectance values ranging from 0.30 to 0.63% Rm. In coals from the middle Benue, vitrinite macerals predominate and Rm values range from 0.74 to 1.25%. The present review suggests that the sub-bituminous coals in the lower and upper Benue are optimum for combustion and sub-optimum for liquefaction; while the high-volatile bituminous coals in the middle Benue, apart form being optimum for liquefaction, are the most suitable as raw material for coke making (carbonization) in steel manufacture

  19. 30 CFR 75.325 - Air quantity.

    Science.gov (United States)

    2010-07-01

    ... coal by simply energizing the equipment on the section. (c) In longwall and shortwall mining systems... utilizing diesel-powered equipment in underground coal mines shall submit to the appropriate MSHA district... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and...

  20. 75 FR 57849 - Maintenance of Incombustible Content of Rock Dust in Underground Coal Mines

    Science.gov (United States)

    2010-09-23

    ... With Constitutionally Protected Property Rights E. Executive Order 12988: Civil Justice Reform F... poverty of families and children. This ETS impacts only the underground bituminous coal mine industry... analysis is required. E. Executive Order 12988: Civil Justice Reform This ETS was written to provide a...

  1. Turning Back Time : Rheological and Microstructural Assessment of Rejuvenated Bitumen

    NARCIS (Netherlands)

    Nahar, S.N.; Schmets, A.J.M.; Schlangen, E.; Shirazi, M.; van de Ven, M.F.C.; Schitter, G.; Scarpas, A.

    2014-01-01

    Countermeasures to the ageing of bituminous asphalt binders is a highly important topic, both for service-life extension of asphalt ‘in the field’ and for recycling old pavements (RAP) into new structures with similar functional requirements as the original structure. Usually this is achieved by

  2. The National Metrology Laboratory of South Africa: the first 50 years (1947-1997)

    CSIR Research Space (South Africa)

    McDowell, M

    1997-01-01

    Full Text Available standards got the treatment it was to expect over the next decades, with the comfortable house being allocated to the new Bituminous Binder Research Unit and Physics of Matter being rewarded with the servants' quarters. To the scientists of those days...

  3. Radwaste treatment and disposal

    International Nuclear Information System (INIS)

    Ehn, L.; Breza, M.; Pekar, A.

    2000-01-01

    In this lecture is given the basic information, that is concerning on the RAW treatment and long term disposal of the treated RAW in repository at Mochovce. Then here is given the basic technical and technological information, that is concerning bituminization, plant, the vitrification unit, center for the RAW-treatment (BSC) and repository at Mochovce. (authors)

  4. Expanded clay hot mix study : final report: part I.

    Science.gov (United States)

    1969-04-01

    This is part I of a two part final report on expanded clay hot mix to: (1) evaluate the use of various expanded clay bituminous mixtures under high traffic counts, (2) accumulate through experience testing, suitable information on the physical proper...

  5. FOSSIL FUEL ENERGY RESOURCES OF ETHIOPIA Wolela Ahmed ...

    African Journals Online (AJOL)

    a

    Ethiopian coals fall under the soft coal series (lignite to bituminous coal), and genetically classified under humic, sapropelic and ... 106 and 653 x 106 to 1 x 109 tones of coal and oil shale deposits registered in Ethiopia, .... gaseous (S1), liquid hydrocarbon, which is released by the thermal breakdown of kerogen appears as ...

  6. CHARACTERIZATION OF DATE PALM FRONDS AS A FUEL FOR ...

    African Journals Online (AJOL)

    relative to liquid water, whereas we call lower heating value when the heat of combustion of the sample is determined relative to ... Bituminous coal ha approximated about 57%. Ajwah and sug. 0.2%. Generally, the fixed carbon conte except to rice husk, and higher than date pa. Table 1. Proximate analysis comparison of ...

  7. Development of nanomodifiers and research into their influence on the properties of bituminous binders Разработка наномодификаторов и исследование их влияния на свойства битумных вяжущих веществ

    Directory of Open Access Journals (Sweden)

    Inozemtsev Sergey Sergeevich

    2013-09-01

    Full Text Available Nine types of nanomodifiers designated for asphalt binder are considered in the article. Three mineral material types of are considered, including dolomite powder MP-1, diatomite and activated silica sand. As the second component cotton oil, synthetic rubber and a colloid solution of ferric (III hydroxide and silica acid are selected. The results of the study disclose the influence of nanomodifiers on needle penetration depth at 0 °C and 25 °C, as well as the softening temperature, brittleness properties and stability after aging. The penetration depth is a criterion of the ability of the bitumen to resist mechanical stress, while brittleness and / or softening are the criteria of its ability to resist temperature. The generalized effectiveness criterion of bitumen modifiers is also taken into account. The generalized effectiveness criterion of nanomodifiers was revealed based on the obtained data. One of the most effective modifiers is diatomite with a colloid solution of ferric hydroxide (III and silica acid. Dolomite powder with sol and diatomite with synthetic rubber (layer 70 nm are promising methods of modification, though they require optimization in terms of their technology and formulations.Рассмотрено несколько вариантов наномодификаторов для битумного вяжущего, синтез которых заключается в нанесении на минеральные компоненты (минеральный порошок МП-1, диатомит, активированный кварцевый песок нанометрового слоя госсиполовой смолы, каучука СКДН или двухкомпонентного золя. Приведены результаты исследования влияния разработанных наномодификаторов на свойства битумного вяжущего. На основании полученных данных проведена критериальная оценка эффективности применения наномодификаторов. Показано, что наиболее эффективным является применение наномодификатора на основе диатомита, обработанного коллоидным раствором гидроксида железа (III и кремниевой кислоты. Представленные данные указывают также на перспективность модифицирования битума добавкой на основе минерального порошка МП-1, обработанного двухкомпонентным золем, и диатомита, обработанного каучуком, которые требуют технологической и рецептурной оптимизации.

  8. Underwater behaviour of bitumen coated radioactive wastes: experimental validation of the Colonbo degradation model; Comportement sous eau des dechets radioactifs bitumes: validation experimentale du modele de degradation Colonbo

    Energy Technology Data Exchange (ETDEWEB)

    Gwinner, B

    2004-03-01

    In the release scenario considered for geologic repository, water is thought to be the main aggressive agent with regards to bituminized radioactive waste (composed in general of 60 weight % of bitumen, 40% of soluble/insoluble salts and a few ppm of radionuclides). Since liquid water can diffuse in pure bitumen, leaching of bituminized waste results in the dissolution of the most soluble salts and leads to the development of a more or less concentrated saline solution-filled pore structure (called permeable layer). In consequence of the generation of a porous layer in the bituminized waste, leaching of salts and radionuclides can then take place. Research performed at the Atomic Energy Commission (CEA) aims therefore at understanding the consequences of ground-water immersion on the transport properties and radionuclides leaching of bituminized waste materials. To this end, a constitutive model (called COLONBO) which describes mathematically the leaching of bituminized waste has been developed. The COLONBO model is based on the following assumptions: 1. Water and dissolved salts migrate in the permeable layer according to Fick's first law. The diffusion of water and salts are quantified by effective diffusion coefficients which are unknown. 2. The mechanical properties of the bitumen matrix are not considered during leaching (free swelling). Up to now, the COLONBO model has been used only to model experimental water uptake and salt leach curves, leading (theoretical) estimates of the effective diffusion coefficients of water and salts in the permeable layer. The aim of this work was to validate experimentally the numerical results obtained with the COLONBO model. First, the correspondence between experimental and simulated water uptake and salt leach rates obtained on various bituminized waste materials is checked, leading estimates of the effective diffusion coefficients of water and salts in the permeable layer. Second, the evolution of the thickness and of

  9. The potential risk of environmental contamination by mercury contained in Polish coal mining waste

    Directory of Open Access Journals (Sweden)

    Tomasz Antoszczyszyn

    2016-01-01

    Full Text Available The paper contains reference literature analysis concerning mercury content in Polish bituminous coal and post-mining waste as well as the impact of mercury content on the environment. The aim of the paper was to determine the occurrence of the risk of contamination of the environment with mercury compounds found in demolition bituminous coal landfills. Mercury, due to its toxic properties has been classified among the most dangerous substances to human health. There are three groups of sources of mercury release into the environment: natural, anthropogenic and remission. Coal mining, its processing and use in the energy sector has the greatest relevance regarding the pollution of the environment with mercury compounds in Poland. A review of reference literature shows that the average content of mercury in Polish bituminous coal varies within a wide range of 41–399 ppb, which is conditional on the origin, age and type of coal. The production of coal has led to a number of facilities in the form of structurally and age-varied landfills, heaps and mining waste dumps. The content of mercury in post-mining waste is in the range from approximately 55 to 380 ppb. The problem of environmental contamination with mercury has attracted considerable interest due to the effects that its concentration have in the biosphere. On the basis of the existing data it has been found that the content of mercury in soils in areas degraded by mining and processing of coal is even 10–16 times higher, compared to the geochemical background. It is necessary to conduct research in this area due to the limited results of research on mercury content in deposited waste from the preparation and flotation of Polish bituminous coals and the potential harmful effect of mercury on the environment. The paper is dedicated to the mercury content in waste from the extraction and processing of bituminous coal.

  10. Close-coupled Catalytic Two-Stage Liquefaction (CTSL{trademark}) process bench studies. Final report, [October 1, 1988--July 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Comolli, A.G.; Johanson, E.S.; Karolkiewicz, W.F.; Lee, L.K.; Popper, G.A.; Stalzer, R.H.; Smith, T.O.

    1993-06-01

    This is the final report of a four year and ten month contract starting on October 1, 1988 to July 31, 1993 with the US Department of Energy to study and improve Close-Coupled Catalytic Two-Stage Direct Liquefaction of coal by producing high yields of distillate with improved quality at lower capital and production costs in comparison to existing technologies. Laboratory, Bench and PDU scale studies on sub-bituminous and bituminous coals are summarized and referenced in this volume. Details are presented in the three topical reports of this contract; CTSL Process Bench Studies and PDU Scale-Up with Sub-Bituminous Coal-DE-88818-TOP-1, CTSL Process Bench Studies with Bituminous Coal-DE-88818-TOP-2, and CTSL Process Laboratory Scale Studies, Modelling and Technical Assessment-DE-88818-TOP-3. Results are summarized on experiments and studies covering several process configurations, cleaned coals, solid separation methods, additives and catalysts both dispersed and supported. Laboratory microautoclave scale experiments, economic analysis and modelling studies are also included along with the PDU-Scale-Up of the CTSL processing of sub-bituminous Black Thunder Mine Wyoming coal. During this DOE/HRI effort, high distillate yields were maintained at higher throughput rates while quality was markedly improved using on-line hydrotreating and cleaned coals. Solid separations options of filtration and delayed coking were evaluated on a Bench-Scale with filtration successfully scaled to a PDU demonstration. Directions for future direct coal liquefaction related work are outlined herein based on the results from this and previous programs.

  11. Radionuclides distribution in blooming of the permian sediments from the Irati Formation of the Parana Basin; Distribuicao de radionuclideos em um afloramento de sedimentos permianos da Formacao Irati na Bacia do Parana

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Ademar de Oliveira

    2008-02-15

    The objective of this work is to study natural radionuclides in sedimentary rocks. The concentration of them reflects the origin of the sediments, the depositional environment as well as some mineralogical characteristics of the rock matrix, and also more recent events as weathering and erosion. Using gamma ray high resolution spectrometry, the profile of activity concentration of the natural radionuclides was assessed for {sup 226}Ra, {sup 238}U, {sup 32}Th and {sup 40}K in rocks of the Irati Formation belonging to Parana Sedimentary Basin. The samples were collected at a limestone abandoned mine, in the city of Sapopema, (PR). 24 samples were collected, eleven from the exposed vertical profile with approximately 5.50 m, whose stratigraphy is represented by an alternation among decimetrics layers of limestones, bituminous shales, and some rhythmits layers (milimetric sheets of limestone and bituminous shales), 9 repetitions of a sample to study the variability, and three rigolits samples in sequential apprenticeships of weathering. Each sample was dried in the sun during about 48 hours, broken, drizzled in a sieve of 4 mesh and put, in a cylindrical container. The measures were accomplished using a Germanium Hyper Pure detector (HPGe) with relative efficiency of 66%, connected to a standard spectrometry electronic chain. The measured concentrations of activity of {sup 238}U were smaller for the limestones (17.80 {+-}0.09 Bq.Kg{sup -1}), larger for the bituminous shales (125.5 {+-} 2.6 Bq.Kg{sup -1} with enrichment of uranium in the sample (200), 548 {+-} 16 Bq.Kg{sup -1}, upper part of the column), and intermediate for the rhythmits (23.0 {+-} 1,3 Bq.Kg{sup -1}. The ratio eTh/K obtained for the studied profiles has equivalent values, indicating similar mineralogical characteristics for the limestones, bituminous shales, rhythmits and studied rigolits. On the other hand, to the ratio eTh/eU showed that two of the three regolits samples belong to oxidizer

  12. Radionuclides distribution in blooming of the permian sediments from the Irati Formation of the Parana Basin

    International Nuclear Information System (INIS)

    Ferreira, Ademar de Oliveira

    2008-02-01

    The objective of this work is to study natural radionuclides in sedimentary rocks. The concentration of them reflects the origin of the sediments, the depositional environment as well as some mineralogical characteristics of the rock matrix, and also more recent events as weathering and erosion. Using gamma ray high resolution spectrometry, the profile of activity concentration of the natural radionuclides was assessed for 226 Ra, 238 U, 32 Th and 40 K in rocks of the Irati Formation belonging to Parana Sedimentary Basin. The samples were collected at a limestone abandoned mine, in the city of Sapopema, (PR). 24 samples were collected, eleven from the exposed vertical profile with approximately 5.50 m, whose stratigraphy is represented by an alternation among decimetrics layers of limestones, bituminous shales, and some rhythmits layers (milimetric sheets of limestone and bituminous shales), 9 repetitions of a sample to study the variability, and three rigolits samples in sequential apprenticeships of weathering. Each sample was dried in the sun during about 48 hours, broken, drizzled in a sieve of 4 mesh and put, in a cylindrical container. The measures were accomplished using a Germanium Hyper Pure detector (HPGe) with relative efficiency of 66%, connected to a standard spectrometry electronic chain. The measured concentrations of activity of 238 U were smaller for the limestones (17.80 ±0.09 Bq.Kg -1 ), larger for the bituminous shales (125.5 ± 2.6 Bq.Kg -1 with enrichment of uranium in the sample (200), 548 ± 16 Bq.Kg -1 , upper part of the column), and intermediate for the rhythmits (23.0 ± 1,3 Bq.Kg -1 . The ratio eTh/K obtained for the studied profiles has equivalent values, indicating similar mineralogical characteristics for the limestones, bituminous shales, rhythmits and studied rigolits. On the other hand, to the ratio eTh/eU showed that two of the three regolits samples belong to oxidizer atmospheres, favoring the leaching of uranium, what can be

  13. Coal biodegradation study; Estudio de Biodegradacion del Carbon

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    A screening procedure has been set up for isolating microorganisms capable of liquefying coal. Spanish coals were used in the tests, namely a brown lignite from Galicia, sub-bituminous coal from Teruel and hard coal from MINAS DE FIGAREDO, S.A. (ASTURIAS). Among the isolated strains several microorganisms proved of liquefying untreated lignite. When lignites were pretreated a more intense and rapid liquefaction was achieved, chelating agents being among the best pretreatments. None of the isolated microorganisms could satisfactorily liquefy sub-bituminous and hard coals in solid media. On the other hand, some fungi grew specifically on the untreated coals, engulfing them and in many cases a soft and slurry was obtained. Several of the isolated microorganisms were able to solubilized all three untreated Spanish coals in liquid media. Coal solubilization was measured spectrophotometrically at 300, 400 and 450 nm.

  14. JV Task 5 - Evaluation of Residual Oil Fly Ash As A Mercury Sorbent For Coal Combustion Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Robert Patton

    2006-12-31

    The mercury adsorption capacity of a residual oil fly ash (ROFA) sample collected form Florida Power and Light Company's Port Everglades Power Plant was evaluated using a bituminous coal combustion flue gas simulator and fixed-bed testing protocol. A size-segregated (>38 {micro}g) fraction of ROFA was ground to a fine powder and brominated to potentially enhance mercury capture. The ROFA and brominated-ROFA were ineffective in capturing or oxidizing the Hg{sup 0} present in a simulated bituminous coal combustion flue gas. In contrast, a commercially available DARCO{reg_sign} FGD initially adsorbed Hg{sup 0} for about an hour and then catalyzed Hg{sup 0} oxidation to produce Hg{sup 2+}. Apparently, the unburned carbon in ROFA needs to be more rigorously activated in order for it to effectively capture and/or oxidize Hg{sup 0}.

  15. Kinetics of coal combustion: Part 3, Mechanisms and kinetics of char combustion

    Energy Technology Data Exchange (ETDEWEB)

    Gavalas, G. R.; Flagan, R. C. [California Inst. of Tech., Pasadena, CA (USA)

    1988-09-01

    This report summarizes a three-year research program aimed at developing this level of understanding of char combustion through a combination of detailed analysis of chars as produced during devolatilization and as they evolve during oxidation, and theoretical studies of the porous microstructures and of pore diffusion and reaction within the coal particles. A small number of coals have been studied in detail, namely a HVA bituminous (PSOC 1451), a sub-bituminous (PSOC 1488), and a lignite (PSOC 1443). Chars have been generated from size-classified samples of these coals by pyrolysis in an inert atmosphere in a drop tube furnace. The chars were then characterized both chemically and physically. Subsequent oxidation studies were performed on these chars. 42 refs., 54 figs., 4 tabs.

  16. Effect of intermolecular cohesion on coal liquefaction. 3. Reactivity of oxygen methylated coal; Sekitan teibunshika hanno ni okeru bunshikan gyoshuryoku no koka. 3. O-methyl ka tan no hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, M.; Nagaishi, H.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    The reactivity of oxygen methylated coal was studied to control hydrogen bond in bituminous coal liquefaction and intermolecular cohesion such as van der Waals force. In experiment, crushed and dried Illinois coal of 100mesh or less was used as specimen, and oxygen methylated coal was prepared by Liotta`s method using tetrabutylammonium halide. Coal liquefaction was conducted in an electromagnetic agitation autoclave using tetralin solvent under initial hydrogen pressure of 100kg/cm{sup 2} while heating. The molecular weight distribution of the products obtained was measured by gel permeation chromatography (GPC) analysis. The experimental results are as follows. The effect of intermolecular cohesion in bituminous coal on the reactivity is mainly derived from decomposing reaction from preasphaltene to oil. Yields of oil fraction by methylation increase corresponding to release of intermolecular cohesion. Since the thermal release is promoted with temperature rise, the difference in yield due to different treatments decreases. 5 refs., 3 figs., 1 tab.

  17. Denitration of medium level liquid radioactive wastes by catalytic destruction of nitrogen oxides

    International Nuclear Information System (INIS)

    Donato, A.; Ricci, G.

    1984-01-01

    The catalytic abatement by means of NH 3 of the NOsub(x) produced in the radwaste conditioning has been studied. With reference to the gas produced in a bituminization plant, the thermodynamics and the chemistry of the NOsub(x) catalytic reduction to nitrogen and H 2 O have been evaluated. The following operational parameters have been experimentally studied: the catalyst bed temperature; the gas residence time; the vapour concentration; the NOsub(x) concentration; the gas velocity; the catalyst grain size distribution; the catalyst time-life. Abatement yields of the order of 99,5% have been obtained following experimental conditions must be selected. In the case of a bituminization plant, a NOsub(x) catalytic reactor, if installed between the evaporator denitrator and the condenser, could reduce to less than 1/100 the volume of the NaNO 3 secondary wastes produced by the gas scrubbing

  18. A Factorial Design Approach to Analyse the Effect of Coarse Recycled Concrete Aggregates on the Properties of Hot Mix Asphalt

    Science.gov (United States)

    Tanty, Kiranbala; Mukharjee, Bibhuti Bhusan; Das, Sudhanshu Shekhar

    2018-02-01

    The present study investigates the effect of replacement of coarse fraction of natural aggregates by recycled concrete aggregates on the properties of hot mix asphalt (HMA) using general factorial design approach. For this two factors i.e. recycled coarse aggregates percentage [RCA (%)] and bitumen content percentage [BC (%)] are considered. Tests have been carried out on the HMA type bituminous concrete, prepared with varying RCA (%) and BC (%). Analysis of variance has been performed on the experimental data to determine the effect of the chosen factors on various parameters such as stability, flow, air void, void mineral aggregate, void filled with bitumen and bulk density. The study depicts that RCA (%) and BC (%) have significant effect on the selected responses as p value is less than the chosen significance level. In addition to above, the outcomes of the statistical analysis indicate that interaction between factors have significant effects on void mineral aggregate and bulk density of bituminous concrete.

  19. Hydrogen usage

    Energy Technology Data Exchange (ETDEWEB)

    1942-10-22

    This short tabular report listed the number of m/sup 3/ of hydrogen required for a (metric) ton of product for various combinations of raw material and product in a hydrogenation procedure. In producing auto gasoline, bituminous coal required 2800 m/sup 3/, brown coal required 2400 m/sup 3/, high-temperature-carbonization tar required 2100 m/sup 3/, bituminous coal distillation tar required 1300 m/sup 3/, brown-coal low-temperature-carbonization tar required 850 m/sup 3/, petroleum residues required 900 m/sup 3/, and gas oil required 500 m/sup 3/. In producing diesel oil, brown coal required 1900 m/sup 3/, whereas petroleum residues required 500 m/sup 3/. In producing diesel oil, lubricants, and paraffin by the TTH (low-temperature-hydrogenation) process, brown-coal low-temperature-carbonization tar required 550 m/sup 3/. 1 table.

  20. A kinetic study of gaseous potassium capture by coal minerals in a high temperature fixed-bed reactor

    DEFF Research Database (Denmark)

    Zheng, Yuanjing; Jensen, Peter Arendt; Jensen, Anker Degn

    2008-01-01

    into long cylindrical pellets. Kaolin and bituminous coal ash that both have significant amounts of Si and Al show superior potassium capture characteristics. Experimental results show that capture of potassium by kaolin is independent of the gas oxygen content. Kaolin releases water and forms metakaolin......The reactions between gaseous potassium chloride and coal minerals were investigated in a lab-scale high temperature fixed-bed reactor using single sorbent pellets. The applied coal minerals included kaolin, mullite, silica, alumina, bituminous coal ash, and lignite coal ash that were formed...... at temperatures below 1300°C. However, the weight gain by mullite is only slightly smaller than that by kaolin in the temperature range of 1300-1500°C. A simple model was developed for the gas-solid reaction between potassium vapor and metakaolin pellet at 900°C....

  1. Analysis of coals and biomass pyrolysis using the distributed activation energy model.

    Science.gov (United States)

    Li, Zhengqi; Liu, Chunlong; Chen, Zhichao; Qian, Juan; Zhao, Wei; Zhu, Qunyi

    2009-01-01

    The thermal decomposition of coals and biomass was studied using thermogravimetric analysis with the distributed activation energy model. The integral method resulted in Datong bituminous coal conversions of 3-73% at activation energies of 100-486 kJ/mol. The corresponding frequency factors were e(19.5)-e(59.0)s(-1). Jindongnan lean coal conversions were 8-52% at activation energies of 100-462 kJ/mol. Their corresponding frequency factors were e(13.0)-e(55.8)s(-1). The conversion of corn-stalk skins were 1-84% at activation energies of 62-169 kJ/mol with frequency factors of e(10.8)-e(26.5)s(-1). Datong bituminous coal, Jindongnan lean coal and corn-stalk skins had approximate Gaussian distribution functions with linear ln k(0) to E relationships.

  2. Experimental Investigation of NO from Pulverized Char Combustion

    DEFF Research Database (Denmark)

    Jensen, Lars Skaarup; Jannerup, Hans Erik; Glarborg, Peter

    2001-01-01

    NO formation and reduction during pulverized char combustion in the temperature range 850–1150°C have been investigated in fixed-bed combustion experiments. Chars from a high-volatile bituminous coal and an anthracite have been used. Under single-particle conditions the selectivity for NO formation......-particle conditions, net NO formation is significantly lower due to NO reduction taking place simultaneously with NO formation. Rate expressions for NO reduction on char both in the presence and in the absence of O2 have been determined. For bituminous coal char, these rates are 10–100 times more rapid than values...... previously reported in literature, but are consistent with reburn-type experiments employing char as fuel. This discrepancy is mainly attributed to rapid char deactivation prior to measuring of NO reduction rates in previous determinations. Shortly after pyrolysis, the effective NO-char reaction rate...

  3. Field cracking performance of airfield rigid pavements

    Directory of Open Access Journals (Sweden)

    Yusuf Mehta

    2017-08-01

    Full Text Available This paper discusses cracking in airport pavements as studied in Construction Cycle 6 of testing carried out at the National Airport Pavement Testing Facility by the Federal Aviation Administration. Pavements of three different flexural strengths as well as two different subgrades, a soft bituminous layer and a more rigid layer known as econocrete, were tested. In addition to this, cracking near two types of isolated transition joints, a reinforced edge joint and a thickened edge joint, was considered. The pavement sections were tested using a moving load simulating that of an aircraft. It has been determined that the degree of cracking was reduced as the flexural strength of the pavement was increased and that fewer cracks formed over the econocrete base than over the bituminous base. In addition, the thickened edge transition joint was more effective in preventing cracking at the edges compared to the reinforced edge joint.

  4. The airport pavements reinforced with Mineral-Asphalt Mixtures’ (MAM layers

    Directory of Open Access Journals (Sweden)

    Jan Marszałek

    2016-09-01

    Full Text Available The article presents original solutions, methodology, and procedure for determining the thickness of bituminous overlays for renovation and modernization of the existing airfield pavements.Using the Westergaard method, the algorithm and nomograms were developed in order to determine the edge stress and the loading force. The nomograms are a state of the art solutions that have never been presented in a similar form. After derivation of aforementioned dependencies, the practical way to use the nomograms, depending on the existing bituminous airport pavement, was demonstrated.The plots were developed on the basis of calculations using the derived equations. They will definitely facilitate the procedure of selecting the thickness of the flexible overlay to the airport pavements which require repair or modernization.[b]Keywords[/b]: airport rigid pavements, airport vulnerable pavements, strengthening the pavement

  5. Historical U.S. Residential Coal Use and Female Lung Cancer Mortality

    Energy Technology Data Exchange (ETDEWEB)

    Cullen, Jennifer; Bogen, Kenneth T.

    2001-03-01

    Recent ecological and case-control studies have indicated elevated lung cancer mortality (LCM) associated with bituminous "smoky" coal use in China, but no similar study has been conducted using U.S. populations. Early 20th century U.S. home cooking and heating fuels were examined in relation to age-specific female LCM, focusing on county-level mortality during 1950-54 to reduce potential inter-county confounding due to cigarette smoking among women aged 40* vs. 60* years (among whom 11% vs. 5% ever smoked, respectively). Overall, a significant relationship was found between female LCM and county-level average per capita bituminous coal use with and without adjustment for numerous covariates in counties where ~75% of homes used coal for heating. This positive association was similar in each female age group after adjustment of 190 combinations of variates considered in addition t

  6. Aspects of solid state 13C CPMAS NMR spectroscopy in coals from the Balkan peninsula

    Directory of Open Access Journals (Sweden)

    ANDREAS GEORGAKOPOULOS

    2003-09-01

    Full Text Available The cross-polarized magic-angle-spinning NMR (CPMAS-NMR technique was used in this work to assess the carbon distribution in coals of different rank (peat, lignite, xylite, sub-bituminous coal from important deposits in Greece and Bulgaria. The technique is assumed to be only semiquantitative, due to a number of interferences, such as spinning side bands (SSB in the spectra, paramagnetic species in the samples, and low or remote protonation of aromatic carbons. The Bulgarian sub-bituminous coal shows the greatest amounts of aromatic structures. The lignite sample from the Drama basin, Northern Greece, is relatively unaltered and largely unweathered, and shows the greatest amounts of aliphatic groups. The 13C-NMR spectra of Pliocene lignites from endemic areas in Serbia and Montenegro and Bosnia, taken from published papers, show significantly more intense resonances for methoxyl, phenolic, and polysaccharide moieties compared to the Drama lignite NMR spectrum. Xylite reveals high contents of carbohydrates.

  7. Fire retardant formulations

    DEFF Research Database (Denmark)

    2017-01-01

    The present invention relates to compositions where a substrate is liable to catch fire such as bituminous products, paints, carpets or the like. The invention relates to a composition comprising 40-95 weight % of a substrate to be rendered fire resistant such as bituminous material or paint......, carpets which substrate is mixed with 5-60 weight % of a fire retardant component. The invention relates to a fire retardant component comprising or being constituted of attapulgite, and a salt being a source of a blowing or expanding agent, where the attapulgite and the salt are electrostatically...... connected by mixing and subjecting the mixture of the two components to agitation. Also, the invention relates to compositions comprising 40-95 weight % of a substrate to be rendered fire resistant mixed with 5-60 weight % of a fire retardant according to claim 1 or 2, which fire retardant component...

  8. Stratigraphy and structure of the northern and western flanks of the Black Hills Uplift, Wyoming, Montana, and South Dakota

    International Nuclear Information System (INIS)

    Robinson, C.S.; Mapel, W.J.; Bergendahl, M.H.

    1981-01-01

    This report describes the stratigraphy and structure of an area of about 5000 square miles in northeastern Wyoming and adjacent parts of Montana and South Dakota. The area includes the northern end and part of the western side of the Black Hills Uplift and the adjoining part of the Powder River Basin. About 11,000 ft of sedimentary rocks ranging in age from Mississippian to Early Tertiary are exposed in the area, not including surficial deposits of Tertiary (.) and Quaternary age. Oil is produced from several fields on the wet side of the Black Hills Uplift in Wyoming. Bentonite is mined at many places. The Fort Union and Wasatch Formations contain large reserves of sub-bituminous coal, and Lakota Formation contains some bituminous coal

  9. PNGMDR 2013-2015. 2015 report by the 'optimisation of the distribution of wastes among management sectors' work-group

    International Nuclear Information System (INIS)

    2015-01-01

    PNGMDR is the French national plan for the management of radioactive materials and wastes. After a discussion of the stakes associated with the optimisation of the different sectors involved in radioactive waste management (production, sorting, processing, packaging, warehousing, storage), this reports proposes a description of wastes for which a sector optimisation study has been performed (graphite wastes, Marcoule bitumen packages, common solid residues, cemented solid wastes in concrete containers from Areva La Hague), describes the various studies optimisation ways and alternate scenarios for these different wastes. It analyses and discusses the progress status of the studies optimisation ways: improvement of the characterisation of graphite and bituminous wastes, studies and works on the storage of low-level-long-lived wastes, studies on the processing of graphite wastes, of bituminous packages and common solid residues. Other issues are evoked: the case of wastes produced by dismantling operations, and a technical-economic approach. Perspectives and future works are discussed for the different considered wastes

  10. Direct Coal Oxidation in Modified Solid Oxide Fuel Cells

    DEFF Research Database (Denmark)

    Deleebeeck, Lisa; Gil, Vanesa; Ippolito, Davide

    2015-01-01

    Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon-carbonate s......Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon......-carbonate slurry or anode layer. The nature of the coal affects both open circuit voltage and power output. Highest OCV and power densities were observed for bituminous coal and by adding manganese oxide or praseodymium-doped ceria to the carbon/carbonate mixture. Comparing the carbon black fueled performance...... bituminous coal (73 mW/cm2). © 2015 ECS - The Electrochemical Society...

  11. Direct Coal Oxidation in Modified Solid Oxide Fuel Cells

    DEFF Research Database (Denmark)

    Deleebeeck, Lisa; Gil, Vanesa; Ippolito, Davide

    2017-01-01

    Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon-carbonate s......Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon......-carbonate slurry or anode layer. The nature of the coal affects both open circuit voltage and power output. Highest OCV and power densities were observed for bituminous coal and by adding manganese oxide or praseodymium-doped ceria to the carbon/carbonate mixture. Comparing the carbon black fueled performance...... bituminous coal (73 mW/cm2)....

  12. NO formation during oxy-fuel combustion of coal and biomass chars

    DEFF Research Database (Denmark)

    Zhao, Ke; Jensen, Anker Degn; Glarborg, Peter

    2014-01-01

    The yields of NO from combustion of bituminous coal, lignite, and biomass chars were investigated in O2/N2 and O2/CO 2 atmospheres. The experiments were performed in a laboratory-scale fixed-bed reactor in the temperature range of 850-1150 °C. To minimize thermal deactivation during char preparat......The yields of NO from combustion of bituminous coal, lignite, and biomass chars were investigated in O2/N2 and O2/CO 2 atmospheres. The experiments were performed in a laboratory-scale fixed-bed reactor in the temperature range of 850-1150 °C. To minimize thermal deactivation during char...

  13. Characterization of Activated Carbon from Coal and Its Application as Adsorbent on Mine Acid Water Treatment

    Directory of Open Access Journals (Sweden)

    Siti Hardianti

    2017-06-01

    Full Text Available Anthracite and Sub-bituminous as activated carbon raw material had been utilized especially in mining field as adsorbent of dangerous heavy metal compound resulted in mining activity. Carbon from coal was activated physically and chemically in various temperature and particle sizes. Characterization was carried out in order to determine the adsorbent specification produced hence can be used and applied accordingly. Proximate and ultimate analysis concluded anthracite has fixed carbon 88.91% while sub-bituminous 49.05%. NaOH was used in chemical activation while heated at 400-500°C whereas physical activation was conducted at 800-1000°C. Activated carbon has high activity in adsorbing indicated by high iodine number resulted from analysis. SEM-EDS result confirmed that activated carbon made from coal has the quality in accordance to SNI and can be used as adsorbent in acid water treatment.

  14. Study on coal char ignition by radiant heat flux.

    Science.gov (United States)

    Korotkikh, A. G.; Slyusarskiy, K. V.

    2017-11-01

    The study on coal char ignition by CO2-continuous laser was carried out. The coal char samples of T-grade bituminous coal and 2B-grade lignite were studied via CO2-laser ignition setup. Ignition delay times were determined at ambient condition in heat flux density range 90–200 W/cm2. The average ignition delay time value for lignite samples were 2 times lower while this difference is larger in high heat flux region and lower in low heat flux region. The kinetic constants for overall oxidation reaction were determined using analytic solution of simplified one-dimensional heat transfer equation with radiant heat transfer boundary condition. The activation energy for lignite char was found to be less than it is for bituminous coal char by approximately 20 %.

  15. An integrated material metabolism model for stocks of urban road system in Beijing, China.

    Science.gov (United States)

    Guo, Zhen; Hu, Dan; Zhang, Fuhua; Huang, Guolong; Xiao, Qiang

    2014-02-01

    Rapid urbanization has greatly altered the urban metabolism of material and energy. As a significant part of the infrastructure, urban roads are being rapidly developed worldwide. Quantitative analysis of metabolic processes on urban road systems, especially the scale, composition and spatial distribution of their stocks, could help to assess the resource appropriation and potential environmental impacts, as well as improve urban metabolism models. In this paper, an integrated model, which covered all types of roads, intersection structures and ancillary facilities, was built for calculating the material stocks of urban road systems. Based on a bottom-up method, the total stocks were disassembled into a number of stock parts rather than obtained by input-output data, which provided an approach promoting data availability and inner structure understanding. The combination with GIS enabled the model to tackle the complex structures of road networks and avoid double counting. In the case study of Beijing, the following results are shown: 1) The total stocks for the entire road system reached 159 million tons, of which nearly 80% was stored in roads, and 20% in ancillary facilities. 2) Macadam was the largest stock (111 million tons), while stone mastic asphalt, polyurethane plastics, and atactic polypropylene accounted for smaller components of the overall system. 3) The stock per unit area of pedestrian overcrossing was higher than that of the other stock units in the entire system, and its steel stocks reached 0.49 t/m(2), which was 10 times as high as that in interchanges. 4) The high stock areas were mainly distributed in ring-shaped and radial expressways, as well as in major interchanges. 5) Expressways and arterials were excessively emphasized, while minor roads were relatively ignored. However, the variation of cross-sectional thickness in branches and neighborhood roads will have a significant impact on the scale of material stocks in the entire road system

  16. Psychophysical Evaluation of Congenital Colour Vision Deficiency: Discrimination between Protans and Deutans Using Mollon-Reffin's Ellipses and the Farnsworth-Munsell 100-Hue Test.

    Science.gov (United States)

    Bento-Torres, Natáli Valim Oliver; Rodrigues, Anderson Raiol; Côrtes, Maria Izabel Tentes; Bonci, Daniela Maria de Oliveira; Ventura, Dora Fix; Silveira, Luiz Carlos de Lima

    2016-01-01

    We have used the Farnsworth-Munsell 100-hue (FM 100) test and Mollon-Reffin (MR) test to evaluate the colour vision of 93 subjects, 30.4 ± 9.7 years old, who had red-green congenital colour vision deficiencies. All subjects lived in Belém (State of Pará, Brazil) and were selected by the State of Pará Traffic Department. Selection criteria comprised the absence of visual dysfunctions other than Daltonism and no history of systemic diseases that could impair the visual system performance. Results from colour vision deficient were compared with those from 127 normal trichromats, 29.3 ± 10.3 years old. For the MR test, measurements were taken around five points of the CIE 1976 colour space, along 20 directions irradiating from each point, in order to determine with high-resolution the corresponding colour discrimination ellipses (MacAdam ellipses). Three parameters were used to compare results obtained from different subjects: diameter of circle with same ellipse area, ratio between ellipse's long and short axes, and ellipse long axis angle. For the FM 100 test, the parameters were: logarithm of the total number of mistakes and positions of mistakes in the FM diagram. Data were also simultaneously analysed in two or three dimensions as well as by using multidimensional cluster analysis. For the MR test, Mollon-Reffin Ellipse #3 (u' = 0.225, v' = 0.415) discriminated more efficiently than the other four ellipses between protans and deutans once it provided larger angular difference in the colour space between protan and deutan confusion lines. The MR test was more sensitive than the FM 100 test. It separated individuals by dysfunctional groups with greater precision, provided a more sophisticated quantitative analysis, and its use is appropriate for a more refined evaluation of different phenotypes of red-green colour vision deficiencies.

  17. Psychophysical Evaluation of Congenital Colour Vision Deficiency: Discrimination between Protans and Deutans Using Mollon-Reffin’s Ellipses and the Farnsworth-Munsell 100-Hue Test

    Science.gov (United States)

    Bento-Torres, Natáli Valim Oliver; Rodrigues, Anderson Raiol; Côrtes, Maria Izabel Tentes; Bonci, Daniela Maria de Oliveira; Ventura, Dora Fix

    2016-01-01

    We have used the Farnsworth-Munsell 100-hue (FM 100) test and Mollon-Reffin (MR) test to evaluate the colour vision of 93 subjects, 30.4 ± 9.7 years old, who had red-green congenital colour vision deficiencies. All subjects lived in Belém (State of Pará, Brazil) and were selected by the State of Pará Traffic Department. Selection criteria comprised the absence of visual dysfunctions other than Daltonism and no history of systemic diseases that could impair the visual system performance. Results from colour vision deficient were compared with those from 127 normal trichromats, 29.3 ± 10.3 years old. For the MR test, measurements were taken around five points of the CIE 1976 colour space, along 20 directions irradiating from each point, in order to determine with high-resolution the corresponding colour discrimination ellipses (MacAdam ellipses). Three parameters were used to compare results obtained from different subjects: diameter of circle with same ellipse area, ratio between ellipse’s long and short axes, and ellipse long axis angle. For the FM 100 test, the parameters were: logarithm of the total number of mistakes and positions of mistakes in the FM diagram. Data were also simultaneously analysed in two or three dimensions as well as by using multidimensional cluster analysis. For the MR test, Mollon-Reffin Ellipse #3 (u’ = 0.225, v’ = 0.415) discriminated more efficiently than the other four ellipses between protans and deutans once it provided larger angular difference in the colour space between protan and deutan confusion lines. The MR test was more sensitive than the FM 100 test. It separated individuals by dysfunctional groups with greater precision, provided a more sophisticated quantitative analysis, and its use is appropriate for a more refined evaluation of different phenotypes of red-green colour vision deficiencies. PMID:27101124

  18. Disposal of radioactive wastes from Czechoslovak nuclear power plants

    International Nuclear Information System (INIS)

    Neumann, L.

    In gaseous radioactive waste disposal, aerosol particles are filtered and gaseous wastes are discharged in the environment. The filters and filter materials used are stored on solid radioactive waste storage sites in the individual power plants. Liquid radioactive wastes are concentrated and the concentrates are stored. Distillates and low-level radioactive waste water are discharged into the hydrosphere. Solid radioactive wastes are stored without treatment in power plant bunkers. Bituminization and cementation of liquid radioactive wastes are discussed. (H.S.)

  19. A380 pavement experimental program-rigid campaign : slab pattern, instrumentation, static test procedure, fatigue test introduction

    OpenAIRE

    LERAT, P; FABRE, C; BALAY, JM

    2003-01-01

    The paper describes several experimentations on rigid pavements at Toulouse Blagnac airport, tested with heavy aircraft landing gear simulator developed by Airbus S.A.S. The main contributors of this program are Airbus, the French Civil Aviation Administration (STBA) and the French Road and Bridges Laboratory (LCPC). The first part of the program (1998 2000) deals with bituminous pavement. In 2001-2002-2003 the program has focused on Rigid tests. The main aim has been therefore to improve th...

  20. Coal-Burning Technologies Applicable to Air Force Central Heating Plants

    Science.gov (United States)

    1989-12-01

    using a process such as the Stretford acid gas removal technology.39 It should be noted that any such treatment of the gas will significantly...or limestone wet scrubbing system *....... . ... **.* .* .** ....** 48 15 Typical spray dryer/particulate collection process flow diagram *...*..*.a...using bituminous coats, this process is expected to produce a hot gas with a higher-heating-value range of about 130 to 180 Btu per dry standard

  1. Tire-to-Surface Friction-Coefficient Measurements with a C-123B Airplane on Various Runway Surfaces

    Science.gov (United States)

    Sawyer, Richard H.; Kolnick, Joseph J.

    1959-01-01

    An investigation was conducted to obtain information on the tire-to-surface friction coefficients available in aircraft braking during the landing run. The tests were made with a C-123B airplane on both wet and dry concrete and bituminous pavements and on snow-covered and ice surfaces at speeds from 12 to 115 knots. Measurements were made of the maximum (incipient skidding) friction coefficient, the full-skidding (locked wheel) friction coefficient, and the wheel slip ratio during braking.

  2. SE-VYZ

    International Nuclear Information System (INIS)

    Anon

    2004-01-01

    On this CD compact disc 6 video-films (A-1 NPP; Bituminization; Cementation; Pressing; The Interim spent fuel storage facility; Transport into the National radioactive waste repository Mochovce; Ignition; and Vitrification). In these films process of radioactive waste treatment in the Bohunice Radioactive Waste Processing Center (SE-VYZ) is presented. 2 presentations about radioactive wastes treatment in the SE-VYZ are included

  3. Mineralogy of fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Moon Young; Park, Suk Whan [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of); Lee, Moo Seung [Chonbuk National University, Chonju (Korea, Republic of)

    1995-12-01

    This study is focused on mineralogical and chemical characteristics of coal fly ash collected from Boreong, Honam, Samcheonpo, Gunsan, Seocheon power plants. Mineralogical and chemical characters of fly ashes are clarified by experimental studies, using x-ray diffractometer, scanning electron microscope, differential thermal analyzer, grain size analyzer and chemical analysis. The results of this study can be summarized as follows; The coal fly ashes from the all power plants are mainly consisted with mullite and quartz, and minor quantity of hematite. In particular, fly ash from the Honam power plant is converted into the anorthite under the 1200 degree. According to the result grain size analysis, most of the fly ashes are under the 200 mesh except 66% of fly ashes from the Boreong and Honam, 54% from Seocheon, 83% from Gunsan and 31% from Samcheonpo power plants. The unburned carbon contents are decreased in the small grain size of fly ashes. Under the 200 mesh grain size of Honam fly ashes shows particularly less than 1% content of unburned carbon. Chemical components of fly ashes are found to be 49-80% of SiO{sub 2} and Al{sub 2}O{sub 3} contents in the bituminous and anthracite coal ash are 49-69% and 75-80%, respectively. The Fe{sub 2}O{sub 3} and CaO concentrations in the bituminous coal ash are higher than anthracite coal ash. The trace elements such as Pb and Zn are higher anthracite coal ash than bituminous coal ash, which is mainly due to the grain size characteristic. The fly ash from Honam power plant with high CaO content can be used potassium silicate fertilizer and raw materials for cements after separation of 200 mesh. Anorthite are formed after 1200 degree heating of bituminous coal ash, which can be utilized as aggregate and bricks. (author). 21 refs., 32 figs., 7 tabs.

  4. Activity report 1979

    International Nuclear Information System (INIS)

    Delande, E.; Drent, W.

    1980-07-01

    The activites of the Eurochemic (European Company for the Chemical Processing of Irradiated Fuels) at Mol is summarized under the following headings: the decontamination and intervention in the Fuel Reception and Storage Building, the active operation of the bituminization facility, the construction of two additional storage bunkers, the full active operation of the section for the handling of solid waste and the construction of various units for the conditioning of organic liquid waste and plutonium hearing solid wastes. (AF)

  5. Factors influencing the selection of the past and future strategies for electricity generation in the Czech Republic

    International Nuclear Information System (INIS)

    Sivek, Martin; Kavina, Pavel; Jirásek, Jakub; Malečková, Veronika

    2012-01-01

    The Czech Republic is the world's sixth largest exporter of electricity. It currently faces a fundamental decision on a new orientation of its energy strategy. Current electricity generation is based on coal (54.7%) and nuclear energy (32.7%). Nowadays the lifespan of the recoverabe reserves is less than 20 years in case of sub-bituminous coal and less than 2 years in case of uranium. Also the original lifespan of all 4 blocks of the power station Dukovany, one of county's two nuclear power plants, is approaching. These are the main reason why the Czech Republic is forced to revise its future energy strategy as well as its current optimal energy mix. This paper analyses the role of individual energy minerals in the future electricity generation portfolio of the Czech Republic. From the point of the energy security, it seems to be optimal to increase the availability of domestic sub-bituminous coal and continue with the preparation of new nuclear energy blocks and extending the lifespan of existing ones. These actions should be supported by investments to the geological survey of domestic uranium deposits. Impartial evaluation of RES potential and impact of their use on the electricity price is advisable simultaneously. - Highlights: ► Czech Republic ranks sixth in the world and fourth in Europe in electricity exports. ► Sub-bituminous coal accounts for 47.7 % of electricity generation, nuclear energy for 32.7%. ► Accessible sub-bituminous coal reserves are decreasing significantly. ► Oil and gas reserves are marginal, uranium reserves are inadequately explored. ► A new energy strategy must be found.

  6. Bitumen and cement solidifications of LL and ML liquid radwaste. The SGN experience

    International Nuclear Information System (INIS)

    Tchemitcheff, E.; Roux, P.

    1993-01-01

    The presentation is focused on the thin-film evaporator technology and the experience gained in the field of the NPPs and research centers on radwaste conditioning. As early as 1970, SGN was licensed by the CEA for the bituminization of LL and ML radwaste. With the support of EDF and COGEMA, SGN has been performing in depth research on cement solidification of borated concentrates and ion exchange resins generated by reactors or reprocessing plant since 1983

  7. Product Manager Combat Engineering and Material Handling Equipment

    Science.gov (United States)

    2012-04-16

    Asphalt Mixing Plant  Skid Steer Loader Type 2 & 3  EMM Water Distributor  Hasty Road Repair  Soil Density Tester  Vibratory Plate Compactor...Engineer/Material Handling Equipment  Eng Rapid Airfield Cont Capability IV  Bituminous Paving Machine  Type 2 Heavy ATEC  Water Well Drill Rig...maneuver support, enable theater access, assured mobility, and airstrip/airfield construction . The FOD also provides earthmoving operational capabilities

  8. Biochemically enhanced methane production from coal

    Science.gov (United States)

    Opara, Aleksandra

    For many years, biogas was connected mostly with the organic matter decomposition in shallow sediments (e.g., wetlands, landfill gas, etc.). Recently, it has been realized that biogenic methane production is ongoing in many hydrocarbon reservoirs. This research examined microbial methane and carbon dioxide generation from coal. As original contributions methane production from various coal materials was examined in classical and electro-biochemical bench-scale reactors using unique, developed facultative microbial consortia that generate methane under anaerobic conditions. Facultative methanogenic populations are important as all known methanogens are strict anaerobes and their application outside laboratory would be problematic. Additional testing examined the influence of environmental conditions, such as pH, salinity, and nutrient amendments on methane and carbon dioxide generation. In 44-day ex-situ bench-scale batch bioreactor tests, up to 300,000 and 250,000 ppm methane was generated from bituminous coal and bituminous coal waste respectively, a significant improvement over 20-40 ppm methane generated from control samples. Chemical degradation of complex hydrocarbons using environmentally benign reagents, prior to microbial biodegradation and methanogenesis, resulted in dissolution of up to 5% bituminous coal and bituminous coal waste and up to 25% lignite in samples tested. Research results confirm that coal waste may be a significant underutilized resource that could be converted to useful fuel. Rapid acidification of lignite samples resulted in low pH (below 4.0), regardless of chemical pretreatment applied, and did not generate significant methane amounts. These results confirmed the importance of monitoring and adjusting in situ and ex situ environmental conditions during methane production. A patented Electro-Biochemical Reactor technology was used to supply electrons and electron acceptor environments, but appeared to influence methane generation in a

  9. Sustainable development with clean coal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-08-01

    This paper discusses the opportunities available with clean coal technologies. Applications include new power plants, retrofitting and repowering of existing power plants, steelmaking, cement making, paper manufacturing, cogeneration facilities, and district heating plants. An appendix describes the clean coal technologies. These include coal preparation (physical cleaning, low-rank upgrading, bituminous coal preparation); combustion technologies (fluidized-bed combustion and NOx control); post-combustion cleaning (particulate control, sulfur dioxide control, nitrogen oxide control); and conversion with the integrated gasification combined cycle.

  10. Improvement of compatibility and stability on polyethylene-modified bitumen by use of an aromatic extra as compatibilizer.

    OpenAIRE

    Viñas Sánchez, María Teresa; Paez, Antonio; Sánchez Caba, Jesús

    2012-01-01

    Bitumen modification by polyethylene addition usually improves the mechanical properties of the binder and, therefore, the behavior in service of the bituminous mix: thermal susceptibility and rutting can be diminished, whilst the resistance to low temperature cracking may increase. To achieve this improvement it is necessary a good compatibility between the base bitumen and the polyethylene. Low compatibility between bitumen and polyethylene can lead to phase separation: the polymer- asph...

  11. DURABILITY OF ASPHALT CONCRETE MIXTURES USING DOLOMITE AGGREGATES

    Directory of Open Access Journals (Sweden)

    Imad Al-Shalout

    2015-12-01

    Full Text Available This study deals with the durability of asphalt concrete, including the effects of different gradations, compaction temperatures and immersion time on the durability potential of mixtures. The specific objectives of this study are: to investigate the effect of compaction temperature on the mechanical properties of asphalt concrete mixtures; investigate the effect of bitumen content and different aggregate gradations on the durability potential of bituminous mixtures.

  12. Major breakthrough in personal dust protection

    Energy Technology Data Exchange (ETDEWEB)

    Chadwick, J.

    2004-09-15

    With new studies highlighting one in every 20 miners developing 'black lung', USA labour, industry and government have joined forces to develop a solution. The rapid advance in Personal Dust Monitor (PDM) technology is a perfect example. The article reports a PDM, which is developed by the US National Institute for Occupational Safety and Health, working in the partnership with the United Mine Workers of America, the Bituminous Coal Operators Association and the National Mining Association.

  13. Production technologies and analysis of use of rubberised asphalt

    OpenAIRE

    Pevec, Rok

    2013-01-01

    Used tires present a major enviormental problem worldwide since most of them are burned as fuel in the cement industry, but most of them lie illegally in landfills in nature. It is identified and confirmed in practice that the properties of bituminous binder, to which rubber particles, which are the product of recycling waste automobile and truck tires, are added, and consequently also the properties of asphalt mixtures are significantly improved. Research in this area and the ...

  14. Characterization of products from pyrolysis of coal with the addition of polyethylene terephthalate

    Czech Academy of Sciences Publication Activity Database

    Havelcová, Martina; Bičáková, Olga; Sýkorová, Ivana; Weishauptová, Zuzana; Melegy, A.

    2016-01-01

    Roč. 154, DEC 15 (2016), 123-131 ISSN 0378-3820 R&D Projects: GA ČR(CZ) GA13-18482S Grant - others:OPPK(XE) CZ.2.16/3.1.00/21538 Program:OPPK Institutional support: RVO:67985891 Keywords : pyrolysis * sub-bituminous coal * polyethylene terephthalate * coke Subject RIV: DD - Geochemistry Impact factor: 3.752, year: 2016

  15. Investigation on the Use of Equivalency Factors for the Design and Evaluation of Flexible Airfield Pavements

    Science.gov (United States)

    2014-03-27

    M o st C o m m o n Lime Clayey soils with a plasticity index (PI) of 12 or more Portland Cement Well-graded sandy gravels or gravelly sands...Hutchinson, Ulery, Ladd, and Barker (1977) utilized three experiments to investigate cement , bituminous, and lime stabilization techniques. From their report...researchers concluded that the equivalency factors for lime , cement , or a combination of lime , cement , and fly ash are calculated as a function of the

  16. Tritium sorption on protective coatings for concrete

    International Nuclear Information System (INIS)

    Miller, J.M.; Senohrabek, J.A.; Allsop, P.A.

    1992-11-01

    Because of the high sorption level of tritium on unprotected concrete, a program to examine the effectiveness of various concrete coatings and sealants in reducing tritium sorption was undertaken, and various exposure conditions were examined. Coatings of epoxy, polyurethane, bituminous sealant, bituminous sealant covered with polyvinylidene chloride wrap, alkyd paint, and sodium silicate were investigated with tritium (HTO) vapor concentration, humidity and contact time being varied. An exposure to HT was also carried out, and the effect of humidity on the tritium desorption rate was investigated. The relative effectiveness of the coatings was in the order of bituminous sealant + wrap > bituminous sealant > solvent-based epoxy > 100%-solids epoxy > alkyd paint > sodium silicate. The commercially available coatings for concrete resulted in tritium sorption being reduced to less than 7% of unprotected concrete. This was improved to ∼0.1% with the use of the Saran wrap (polyvinylidene chloride). The amount of tritium sorbed was proportional to tritium concentration. The total tritium sorbed decreased with an increase in humidity. A saturation effect was observed with increasing exposure time for both the coated and unprotected samples. Under the test conditions, complete saturation was not achieved within the maximum 8-hour contact time, except for the solvent-based epoxy. The desorption rate increased with a higher-humidity air purge stream. HT desorbed more rapidly than HTO, but the amount sorbed was smaller. The experimental program showed that HTO sorption by concrete can be significantly reduced with the proper choice of coating. However, tritium sorption on concrete and proposed coatings will continue to be a concern until the effects of the various conditions that affect the adsorption and desorption of tritium are firmly established for both chronic and acute tritium release conditions. Material sorption characteristics must also be considered in

  17. Power industry and the environment III

    International Nuclear Information System (INIS)

    1993-11-01

    The conference was primarily concerned with the future role of brown and bituminous coal in the energy policy of the Czech Republic and with their environmental impacts. Attention was also paid to remediation of consequences of open pit mining in the North Bohemian brown coal district and to the environmental impacts of coal-fired power plants operated by the CEZ utility, especially to air pollution with sulfur dioxide in northwestern Bohemia. (J.B.)

  18. Apparatus for entrained coal pyrolysis

    Science.gov (United States)

    Durai-Swamy, Kandaswamy

    1982-11-16

    This invention discloses a process and apparatus for pyrolyzing particulate coal by heating with a particulate solid heating media in a transport reactor. The invention tends to dampen fluctuations in the flow of heating media upstream of the pyrolysis zone, and by so doing forms a substantially continuous and substantially uniform annular column of heating media flowing downwardly along the inside diameter of the reactor. The invention is particularly useful for bituminous or agglomerative type coals.

  19. Pyrolysis process and apparatus

    Science.gov (United States)

    Lee, Chang-Kuei

    1983-01-01

    This invention discloses a process and apparatus for pyrolyzing particulate coal by heating with a particulate solid heating media in a transport reactor. The invention tends to dampen fluctuations in the flow of heating media upstream of the pyrolysis zone, and by so doing forms a substantially continuous and substantially uniform annular column of heating media flowing downwardly along the inside diameter of the reactor. The invention is particularly useful for bituminous or agglomerative type coals.

  20. Advanced coal liquefaction research: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gall, W.; McIlvried, III, H. G.

    1988-07-01

    This study had two objectives: (1) To enhance the fundamental understanding of observed differences in the short contact time, donor solvent liquefaction of bituminous and subbituminous coals. (2) To determine if physical refining of subbituminous coals could be used to give a better feedstock for the first stage of two-stage liquefaction processes. Liquefaction studies using microautoclaves were carried out. Results are discussed. 11 refs., 25 figs., 29 tabs.

  1. Assessment of low-rank (LRC) drying technologies

    International Nuclear Information System (INIS)

    Willson, W.G.; Young, B.C.; Irwinj, W.

    1992-01-01

    This paper reports that low-rank coals (LRCs), brown, lignitic, and subbituminous coals, represent nearly half of the estimated coal resources in the world. In many of the developing nations, LRCs are the only source of low-cost energy. LRCs are geologically younger than higher-rank bituminous coals and are typically present in thick seams with less cover (overburden) than bituminous coals, making them recoverable by low-cost strip mining. Current pit-head coal prices for LRCs range from a low of around $0.25 per MM Btus for subbituminous coals from the USA's Powder River Basin, to highs of around $1,00 for those that are more costly to mine. On the other hand, the pit-head price of bituminous coals in the USA range from a low of around $1 to over $2 per MM Btu. Unfortunately, this differential in favor of LRC is more than offset in distant markers where, until now, it has been considered a nuisance. Often less than half of its weight is combustible, the rest being water and ash. Thus the cost of hauling it any distance at all in its untreated dry bulk form is prohibitive. However, from a utilization aspect, LRCs have a lower fuel ration (fixed carbon to volatile matter) and are typically an order of magnitude more reactive than bituminous coals. Many LRCs, including the enormous reserves in Alaska, Australia, and Indonesia, also have extremely low sulfur contents of only a few tenths of a percent. Low mining costs, high reactivity, and extremely low sulfur content would make these coals premium fuel were it not for their high moisture levels, which range from around 25% w/w to over 60% w/w. High moisture creates a mistaken perception, among major coal importers, of inferior quality, and the many positive features of LRCs are overlooked

  2. Mechanisms and interaction phenomena influencing releases in a low- and medium-level waste disposal system

    International Nuclear Information System (INIS)

    Brodersen, K.; Nilsson, K.

    1991-01-01

    The report covers work done 1986-1990 at Riso National Laboratory as part of the third EC Research Programme on Radioactive Waste Management. The report is divided into three parts: 1) Waste product characterization: - leaching and volume stability of cemented ion-exchange resins. - Hydroscopic properties of cemented and bituminized radioactive waste. - Water uptake and swelling of bituminized waste, water migration in bitumen membranes and measurements of swelling pressures. - Ageing of bituminized products. 2) Barrier material properties: - The influence of the pore structure in concrete on the hydraulic transport of water and ions through concrete barriers was investigated - Healing of cracks in concrete barriers by precipitation of calcium carbonate was demonstrated experimentally - Transport of components between two thin plates of cement paste with different composition stored together in water - The structure of degraded cement paste was studied using SANS (small angle neutron scattering). 3) Interaction phenomena: - Integral experiments with migration of radioisotopes from cemented waste through barriers made from kaolin, chalk or concrete were made under different external conditions. 51 figs., 15 tabs., 25 refs

  3. Extraction of low rank coals by coal derived oils at 350 degrees C for producing clean fuels

    Energy Technology Data Exchange (ETDEWEB)

    Miura, K.; Mae, K.; Shindo, H.; Ashida, R.; Ihara, T. [Kyoto University, Kyoto (Japan). Dept. of Chemistry

    2003-07-01

    The authors have recently presented a new coal solvent extraction method that enhances the extraction yield dramatically. The method extracts coal using a flowing stream of either tetralin or 1-methylnaphthalene under 10 MPa at 200 to 400{sup o}C. The extract yield reached 65 to 80% for bituminous coals at 350{sup o}C, and the extract was almost free from mineral matter. Thus, this method was found to be effective to recover clean fuels from bituminous coals under rather mild conditions. To extend the extraction method to low rank coals and to make the method practically applicable, coal derived oils, carbol oil and creosote oil, were used in addition to tetralin in this study. Twenty kinds of coals were subjected to the extraction by tetralin and the coal derived oils at 350{sup o}C. Almost all sub-bituminous coals and brown coals examined were surprisingly extracted by 80% in the carbol oil at 350{sup o}C. It was also found that the extract was almost free from mineral matter and that most of sulfur was retained in the coal through the extraction by tetralin, whereas most of sulfur including pyritic sulfur was transferred into the soluble fraction through the extraction by the carbol oil. Thus, it was clarified that the proposed method was effective to produce a large amount of clean fuels from low rank coals under rather mild conditions.

  4. Formation and retention of methane in coal

    Energy Technology Data Exchange (ETDEWEB)

    Hucka, V.J.; Bodily, D.M.; Huang, H.

    1992-05-15

    The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seams and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.

  5. Formation and retention of methane in coal. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hucka, V.J.; Bodily, D.M.; Huang, H.

    1992-05-15

    The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seams and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.

  6. Asphalt mixtures with a high amount of RAP - case study

    Science.gov (United States)

    Koudelka, Tomas; Varaus, Michal

    2017-09-01

    A case study of one trial section in the Pilsen region is presented. The pavement in the section was newly constructed in 2015 using one type of an asphalt concrete mixtures with varying RAP content. The constructed surface course comprises of 0% to 50% RAP. In order to restore the aged binder properties and to avoid the embrittlement of the produced mixtures, a rubber-based modifier/rejuvenator was employed. For technological reasons during manufacturing processes, which engage a parallel drying drum, a crude oil-based rejuvenator was also added. This article contains the preliminary data from an on-going project focused on monitoring the properties of bituminous binders contained in asphalt mixtures. The actual bituminous binders were extracted straight after production, after 6 months and after 12 months. The binder characteristics are evaluated using empirical testing as well as functional tests. Low temperature properties are measured by a Bending Beam Rheometer (BBR). The preliminary results show, that the bituminous binders properties change significantly in a relatively short period of time. The progress in binder’ characteristics is contradictory to up-to date knowledge. The probability that the phenomenon of diffusion between aged binder and rejuvenator agents occurs exists. Moreover, the data might indicate that the process of rejuvenator evaporation takes place.

  7. Spectroscopy study of electron spin resonance of coal oxidation of different rank

    International Nuclear Information System (INIS)

    Enciso Prieto, Hector Manuel

    1992-01-01

    The present work constitutes an initial step for the knowledge of the coal oxidation, with the purpose of preventing the adverse influences caused by this phenomenon in the physical-chemical characteristics and in the tendency to the spontaneous combustion. Since the knowledge the influence of the free radicals in this process, their relative concentration was measured by means of the use of the technique of resonance spin electron. This technique measures the absorption of electromagnetic radiation, generally in the microwaves region, for the materials that not have electrons matched up in a strong magnetic field. In the essays of oxidation three coal of different range and different characteristics of mass were used and it was studied the influence of the temperature, particle size and the range. The results showed that the coal of Guacheta (bituminous low in volatile) it presents bigger concentration of free radicals, after the reaction with the atmospheric oxygen, with regard to the coal of the Cerrejon (bituminous high in volatile B) and Amaga (bituminous high in volatile C). Although this doesn't indicate that the coal of Guacheta is that more easily is oxidized, but rather it possibly presents stabilization of radicals for resonance. It concluded that there are differences in the oxidation mechanism between coal of different rank and different agglomeration properties

  8. Oxy-fuel combustion of millimeter-sized coal char: Particle temperatures and NO formation

    DEFF Research Database (Denmark)

    Brix, Jacob; Navascués, Leyre Gómez; Nielsen, Joachim Bachmann

    2013-01-01

    as the O2 concentration or the particle size increased. However, for the bituminous coal char, a peak in NO yield was observed at an intermediate particle size of 0.1–0.2 g. The differences in the effect of gas atmosphere, O2 concentration, and particle mass on the NO yield from oxidation of bituminous...... coal char and lignite char, respectively, cannot be fully explained. Char/NO interactions appear to be quite complex, and mineral catalysis and release to the gas-phase of volatile N-species such as HCN, either from secondary pyrolysis or as a product of the char–N + O2 reaction, may play a role.......In this work, differences in particle temperature and NO yield during char oxidation in O2/N2 and O2/CO2 atmospheres, respectively, have been examined. A laboratory scale fixed bed reactor, operated isothermally at 1073 K, was used for combustion of millimeter-sized lignite and bituminous coal char...

  9. Mechanical Properties of Non-Woven Polyester Fibers and Polymer-Modified Bitumen Composites

    Directory of Open Access Journals (Sweden)

    V. Hadadi

    2007-12-01

    Full Text Available Blown bitumen (110/10 was mixed with heavy vacuum slops (H.V.S, 60/70 penetration grade bitumen and recycled isotactic polypropylene (iPP at different levels. The resulting resins were used to impregnate non-woven poly(ethylene terephthalate fibers to form composites. The modulus and penetration grade of the resulting bituminous resins were determined. It was found that these bituminous resins drastically affect the modulus of the composites formed by low-Young’s modulus fibers such as polyesters. Consequently, interactions between resin and fibers and the correlation length of asphalthenes (in absence of iPP and interdiffused coalescence and segregated network of asphalthenes (in presence of iPP result in a non-linear behavior of composite’s modulus. The behavior of the composites with or without iPP is controlled by resin toughness and resin interactions with the fiber through the viscosity. Comparison of the experimental composite modulus data with the theoretical modulus data revealed that the Takayanangi’s model best predicts the behavior of these composites. The adjustment factors of this model were reported and proposed as an indication of fiber-resin interaction. It was also found that the modulus of fibers is affected by toughness, viscosity and the iPP content of the bituminous resin.

  10. Organic emissions from coal pyrolysis: mutagenic effects.

    Science.gov (United States)

    Braun, A G; Wornat, M J; Mitra, A; Sarofim, A F

    1987-01-01

    Four different types of coal have been pyrolyzed in a laminar flow, drop tube furnace in order to establish a relationship between polycyclic aromatic compound (PAC) evolution and mutagenicity. Temperatures of 900K to 1700K and particle residence times up to 0.3 sec were chosen to best simulate conditions of rapid rate pyrolysis in pulverized (44-53 microns) coal combustion. The specific mutagenic activity (i.e., the activity per unit sample weight) of extracts from particulates and volatiles captured on XAD-2 resin varied with coal type according to the order: subbituminous greater than high volatile bituminous greater than lignite greater than anthracite. Total mutagenic activity (the activity per gram of coal pyrolyzed), however, varied with coal type according to the order: high volatile bituminous much greater than subbituminous = lignite much greater than anthracite, due primarily to high organic yield during high volatile bituminous coal pyrolysis. Specific mutagenic activity peaked in a temperature range of 1300K to 1500K and generally appeared at higher temperatures and longer residence times than peak PAC production. PMID:3311724

  11. Thermal analysis and kinetics of coal during oxy-fuel combustion

    Science.gov (United States)

    Kosowska-Golachowska, Monika

    2017-08-01

    The pyrolysis and oxy-fuel combustion characteristics of Polish bituminous coal were studied using non-isothermal thermogravimetric analysis. Pyrolysis tests showed that the mass loss profiles were almost similar up to 870°C in both N2 and CO2 atmospheres, while further mass loss occurred in CO2 atmosphere at higher temperatures due to char-CO2 gasification. Replacement of N2 in the combustion environment by CO2 delayed the combustion of bituminous coal. At elevated oxygen levels, TG/DTG profiles shifted through lower temperature zone, ignition and burnout temperatures decreased and mass loss rate significantly increased and complete combustion was achieved at lower temperatures and shorter times. Kinetic analysis for the tested coal was performed using Kissinger-Akahira-Sunose (KAS) method. The activation energies of bituminous coal combustion at the similar oxygen content in oxy-fuel with that of air were higher than that in air atmosphere. The results indicated that, with O2 concentration increasing, the activation energies decreased.

  12. Hydrogasification of various carbonaceous sources using pressure change properties

    Energy Technology Data Exchange (ETDEWEB)

    Cha, W.S.; Baek, I.H.; Jang, H.T. [Kunsan National University, Kunsan (Republic of Korea)

    2007-05-15

    Hydrogasification experiments were carried out in a batch reactor capable of operating at 800{sup o}C and 8 MPa. Carbonaceous matters used in the experiments were bituminous and anthracite coal and sawdust. It was found that the decreasing rate of hydrogen gas pressure was closely related to the rate of gas production. This result was confirmed by the change of char conversion. The methane content in the gas products and char conversion rose with the increase of temperature and pressure. The addition of water activated the hydrogasification reaction until the proper level of water amount (up to 30 wt%), but an excess level of water inhibited the reaction. The activation energy of bituminous coal and sawdust char obtained by the Arrhenius plot was 187 KJ/mole and 77 KJ/mole, respectively. In case of loading of catalysts, all catalysts loaded to the char did not give a positive effect in hydrogasification, but the catalytic effect depended on type of catalyst metals and char. In the present hydrogasification of bituminous coal and sawdust, the order of activities for the catalysts tested was K{sub 2}CO{sub 3} does not satisfy NaCO{sub 3} {gt} Fe(NO{sub 3}{sup 2}){gt} Ni(NO{sub 3}{sup 2}){gt} FeSO{sub 4}.

  13. Photocatalyticpaving concrete

    Directory of Open Access Journals (Sweden)

    Lyapidevskaya Ol'ga Borisovna

    2014-02-01

    Full Text Available Today bituminous concrete is a conventional paving material. Among its advantages one can name dustlessness and noiselessness, fine wear (up to 1 mm a year and fine maintainability. As the main disadvantages of this material one can name high slipperiness under humidification, low durability and weather resistance. Besides that, during placement of the bituminous concrete a lot of different air pollutants are emitted, which are harmful for environment and human’s health (they are listed in the paper according to the US Environmental Protection Agency materials. As an alternative, one can use cement-concrete pavement, which is in many ways more efficient than the bituminous concrete. It is proposed to enhance environmental performance of the cement-concrete pavement via usage of photocatalysis. The mechanism of different photocatalytic reactions is described in the paper, namely heterogeneous and homogeneous photocatalysis, photo-induces, photoactivated catalysis and catalytical photoreactions. It is pro-posed to use heterogeneous photocatalysis with titanium dioxide as a photocatalyst. The mechanism of photo oxidation of air contaminants, with the usage of titanium dioxide is2described. The paper sets problems, connected with the sensibilization of TiOto thevisible light (it is proposed to use titanium dioxide, doped with the atoms of certain elements to increase its sensibility to the visible light and with the development of a new photocatalytic paving concrete, which will meet the requirements, specified for paving in the climatic and traffic conditions of the Russian Federation.

  14. The release of iron during coal combustion. Milestone report

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, L.L. [Sandia National Labs., Livermore, CA (United States). Combustion Research Facility

    1995-06-01

    Iron plays an important role in the formation of both fly ash and deposits in many pulverized-coal-fired boilers. Several authors indicate that iron content is a significant indicator of the slagging propensity of a majority of US bituminous coals, in particular eastern bituminous coals. The pyritic iron content of these coals is shown to be a particularly relevant consideration. A series of investigations of iron release during combustion is reported for a suite of coals ranging in rank from lignite to low-volatile bituminous coal under combustion conditions ranging from oxidizing to inert. Experimental measurements are described in which, under selected conditions, major fractions of the iron in the coal are released within a 25 ms period immediately following coal devolatilization. Mechanistic interpretation of the data suggest that the iron is released as a consequence of oxygen attack on porous pyrrhotite particles. Experimental testing of the proposed mechanism reveals that the release is dependent on the presence of both pyrite in the raw coal and oxygen in the gas phase, that slow preoxidation (weathering) of the pyrite significantly inhibits the iron release, and that iron loss increases as oxygen penetration of the particle increases. Each observation is consistent with the postulated mechanism.

  15. Laboratory and On-Site Tests for Rapid Runway Repair

    Directory of Open Access Journals (Sweden)

    Federico Leonelli

    2017-11-01

    Full Text Available The attention to rapid pavement repair has grown fast in recent decades: this topic is strategic for the airport management process for civil purposes and peacekeeping missions. This work presents the results of laboratory and on-site tests for rapid runway repair, in order to analyse and compare technical and mechanical performances of 12 different materials currently used in airport. The study focuses on site repairs, a technique adopted most frequently than repairs with modular elements. After describing mechanical and physical properties of the examined materials (2 bituminous emulsions, 5 cement mortars, 4 cold bituminous mixtures and 1 expanding resin, the study presents the results of carried out mechanical tests. The results demonstrate that the best performing material is a one-component fast setting and hardening cement mortar with graded aggregates. This material allows the runway reopening 6 h after the work. A cold bituminous mixture (bicomponent premixed cold asphalt with water as catalyst and the ordinary cement concrete allow the reopening to traffic after 18 h, but both ensure a lower service life (1000 coverages than the cement mortar (10,000 coverages. The obtained results include important information both laboratory level and field, and they could be used by airport management bodies and road agencies when scheduling and evaluating pavement repairs.

  16. Development of methods for treatment and conditioning of biological radioactive waste in the Czech Republic

    International Nuclear Information System (INIS)

    Holub, J.

    1997-01-01

    Incineration of biological radioactive waste was performed in a facility manufactured in the Czech Republic for combustion of burnable, radioactive and non-radioactive residues. The equipment has shown an adequate capability for combustion of biological waste. Basic technical parameters of the incinerator SP-603 can guarantee combustion of majority of wastes from different radionuclide users in the country. To ensure proper further handling with the resulting ash, three conditioning options were studied, the bituminization process, incorporation into cement, and embedding of ash into a mixture of bituminous and cementitious materials. Mechanical properties of the conditioned ash were in good compliance with those published elsewhere. Bituminized ash exhibits lowest leachibility, followed by the ash conditioned by means of the mixed process. Potential abnormal operation conditions were evaluated and their consequences assessed. The evaluation encompassed sensitivity analysis of the consequences potentially affecting the operating staff, nearby population and the environment. Cost estimate was carried out using a national approach for the calculation. From the results it can be seen that there are no large differences between the conditioning and disposal of wastes resulting from different conditioning processes. (author). 16 refs, 4 figs, 15 tabs

  17. The analysis of mercury content in coals and ashes

    Directory of Open Access Journals (Sweden)

    Kasprzyk Marta

    2017-01-01

    Full Text Available It is well known that mercury that enters the atmosphere is a serious threat to the natural environment. From the available literature, it can be stated that fossil fuels are among the main carriers of this fuel. The question arises whether it is the right approach. While the enrichment of bituminous coal produces limited amounts of mercury, they are being released into the atmosphere as a result of the combustion of coal. The situation is similar in the case of biomass, which releases large amounts of mercury into the atmosphere when subjected to the combustion process. While bituminous coal is the carrier of mercury, the application of currently known technology, rational production and the use of fossil fuels make it possible to maximally minimize mercury emissions into the atmosphere. This study evaluated the mercury content in the ashes resulting from the combustion of bituminous coal subjected to the enrichment process. The samples were collected from ten mines located in the Polish part of the Upper Silesian Coal Basin (USCB. In total, thirty coal samples and thirty products of the combustion process were examined. All sixty samples were subjected to physicochemical analysis, including: moisture content, ash content, sulfur content, carbon content, and Gross Calorific Value.

  18. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Gary Blythe

    2007-05-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB cofired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems to be tested. IPL, an AES company, provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Degussa Corporation is providing the TMT-15 additive and technical support to the test program as cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot

  19. Risk Assessment and Monitoring of Stored CO2 in Organic Rocks Under Non-Equilibrium Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Malhotra, Vivak

    2014-06-30

    The USA is embarking upon tackling the serious environmental challenges posed to the world by greenhouse gases, especially carbon dioxide (CO2). The dimension of the problem is daunting. In fact, according to the Energy Information Agency, nearly 6 billion metric tons of CO2 were produced in the USA in 2007 with coal-burning power plants contributing about 2 billion metric tons. To mitigate the concerns associated with CO2 emission, geological sequestration holds promise. Among the potential geological storage sites, unmineable coal seams and shale formations in particular show promise because of the probability of methane recovery while sequestering the CO2. However. the success of large-scale sequestration of CO2 in coal and shale would hinge on a thorough understanding of CO2's interactions with host reservoirs. An important parameter for successful storage of CO2 reservoirs would be whether the pressurized CO2 would remain invariant in coal and shale formations under reasonable internal and/or external perturbations. Recent research has brought to the fore the potential of induced seismicity, which may result in caprock compromise. Therefore, to evaluate the potential risks involved in sequestering CO2 in Illinois bituminous coal seams and shale, we studied: (i) the mechanical behavior of Murphysboro (Illinois) and Houchin Creek (Illinois) coals, (ii) thermodynamic behavior of Illinois bituminous coal at - 100oC ≤ T ≤ 300oC, (iii) how high pressure CO2 (up to 20.7 MPa) modifies the viscosity of the host, (iv) the rate of emission of CO2 from Illinois bituminous coal and shale cores if the cores, which were pressurized with high pressure (≤ 20.7 MPa) CO2, were exposed to an atmospheric pressure, simulating the development of leakage pathways, (v) whether there are any fractions of CO2 stored in these hosts which are resistance to emission by simply exposing the cores to atmospheric pressure, and (vi) how compressive shockwaves applied to the coal and

  20. Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

    Science.gov (United States)

    Kostova, I.J.; Hower, J.C.; Mastalerz, Maria; Vassilev, S.V.

    2011-01-01

    Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture. ?? 2010 Elsevier Ltd.

  1. Soot, organics, and ultrafine ash from air- and oxy-fired coal combustion

    KAUST Repository

    Andersen, Myrrha E.

    2016-10-19

    Pulverized bituminous coal was burned in a 10. W externally heated entrained flow furnace under air-combustion and three oxy-combustion inlet oxygen conditions (28, 32, and 36%). Experiments were designed to produce flames with practically relevant stoichiometric ratios (SR. =1.2-1.4) and constant residence times (2.3. s). Size-classified fly ash samples were collected, and measurements focused on the soot, elemental carbon (EC), and organic carbon (OC) composition of the total and ultrafine (<0.6. μm) fly ash. Results indicate that although the total fly ash carbon, as measured by loss on ignition, was always acceptably low (<2%) with all three oxy-combustion conditions lower than air-combustion, the ultrafine fly ash for both air-fired and oxy-fired combustion conditions consists primarily of carbonaceous material (50-95%). Carbonaceous components on particles <0.6. μm measured by a thermal optical method showed that large fractions (52-93%) consisted of OC rather than EC, as expected. This observation was supported by thermogravimetric analysis indicating that for the air, 28% oxy, and 32% oxy conditions, 14-71% of this material may be OC volatilizing between 100. C and 550. C with the remaining 29-86% being EC/soot. However, for the 36% oxy condition, OC may comprise over 90% of the ultrafine carbon with a much smaller EC/soot contribution. These data were interpreted by considering the effects of oxy-combustion on flame attachment, ignition delay, and soot oxidation of a bituminous coal, and the effects of these processes on OC and EC emissions. Flame aerodynamics and inlet oxidant composition may influence emissions of organic hazardous air pollutants (HAPs) from a bituminous coal. During oxy-coal combustion, judicious control of inlet oxygen concentration and placement may be used to minimize organic HAP and soot emissions.

  2. Flash hydropyrolysis of coal. Quarterly report No. 11, October 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Steinberg, M.; Fallon, P.; Bhatt, B.L.

    1980-02-01

    The following conclusions can be drawn from this work: (1) when the caking bituminous coals are used with diluents, only 20% Pittsburgh No. 8 coal can be added to the diluent swhile 40% Illinois No. 6 could be added due to the higher free swelling index of the Pittsburgh No. 8; (2) When limestone is used as a diluent, considerably more sulfur is retained in the char than when using sand; (3) when the char from an experiment using limestone is recycled as the diluent for another experiment, the char continually retains additional sulfur through at least three recycles; (4) decomposition of the limestone and reduction is indicated by the high concentrations of CO observed at 900/sup 0/C; (5) increasing the coal feed rate by a factor of 4 from 2.4 to 10.7 lb/hr at low H/sub 2//Coal ratios (approx. = 0.6) results in no appreciable change in gaseous HC yields (approx. = 27%) or concentration (approx. = 45%) but higher BTX yields (1.1% vs. 5.4%); (6) although only one experiment was conducted, it appears that hydrogasification of untreated New Mexico sub-bituminous coal at 950/sup 0/C does not give an increase in yield over hydrogasification at 900/sup 0/C; (7) the hydrogasification of Wyodak lignite gives approximately the same gaseous HC yields as that obtained from North Dakota lignite but higher BTX yields particularly at 900/sup 0/C and 1000 psi (9% vs. 2%); (8) treating New Mexico sub-bituminous coal with NaCO/sub 3/ does not increase its hydrogasification qualities between 600/sup 0/C and 900/sup 0/C at 1000 psi but does decrease the BTX yield.

  3. Mechanisms and interaction phenomena influencing releases in low- and medium-level waste disposal systems

    International Nuclear Information System (INIS)

    Brodersen, K.; Nilsson, K.

    1990-11-01

    The report covers work done 1986-1990 at Risoe National Laboratory as part of the third EC Research Programme on Radioactive Waste Management. Waste product characterization: Leaching and volume stability of cemented ion-exchange resins. Wet/dry cycling was found to be an important degradation mechanism. Hygroscopic properties of cemented and bituminized radioactive waste. Water uptake from the air can be an important release mechanism when waste containing soluble salts are disposed of by shallow land burial. Water uptake and swelling of bituminized waste including studies on water migration in bitumen membranes and measurements of swelling pressures. Ageing of bituminized products was demonstrated to result in increasing stiffness of the materials. Nickel ferrocyanide in precipitation sludge was found to be unstable in contact with concrete. Barrier material properties: The influence of the pore structure in concrete on the hydraulic or diffusive transport of water and ions through concrete barriers was investigated. The main parameter is the water/cement ratio. A theoretical interpretation is given. Healing of cracks in concrete barriers by precipitation of calcium carbonate was demonstrated experimentally and described by a simplified model. Transport of components between two thin plates of cement paste with different composition stored together in water was found to take place at a low rate. The structure of degraded cement paste was studied using SANS (small angle neutron scattering). Interaction phenomena: - Integral experiments with migration of radioisotopes from cemented waste through barriers made from kaolin, chalk or concrete were made under different external conditions. The results can be used for model validation and some preliminary work was done. (author) 16 tabs., 51 ills., 25 refs

  4. Studies of the fate of sulfur trioxide in coal-fired utility boilers based on modified selected condensation methods.

    Science.gov (United States)

    Cao, Yan; Zhou, Hongcang; Jiang, Wu; Chen, Chien-Wei; Pan, Wei-Ping

    2010-05-01

    The formation of sulfur trioxide (SO(3)) in coal-fired utility boilers can have negative effects on boiler performance and operation, such as fouling and corrosion of equipment, efficiency loss in the air preheater (APH), increase in stack opacity, and the formation of PM(2.5). Sulfur trioxide can also compete with mercury when bonding with injected activated carbons. Tests in a lab-scale reactor confirmed there are major interferences between fly ash and SO(3) during SO(3) sampling. A modified SO(3) procedure to maximize the elimination of measurement biases, based on the inertial-filter-sampling and the selective-condensation-collecting of SO(3), was applied in SO(3) tests in three full-scale utility boilers. For the two units burning bituminous coal, SO(3) levels starting at 20 to 25 ppmv at the inlet to the selective catalytic reduction (SCR), increased slightly across the SCR, owing to catalytic conversion of SO(2) to SO(3,) and then declined in other air pollutant control device (APCD) modules downstream to approximately 5 ppmv and 15 ppmv at the two sites, respectively. In the unit burning sub-bituminous coal, the much lower initial concentration of SO(3) estimated to be approximately 1.5 ppmv at the inlet to the SCR was reduced to about 0.8 ppmv across the SCR and to about 0.3 ppmv at the exit of the wet flue gas desulfurization (WFGD). The SO(3) removal efficiency across the WFGD scrubbers at the three sites was generally 35% or less. Reductions in SO(3) across either the APH or the dry electrostatic precipitator (ESP) in units burning high-sulfur bituminous coal were attributed to operating temperatures being below the dew point of SO(3).

  5. Single-coal-particle combustion in O{sub 2}/N{sub 2} and O{sub 2}/CO{sub 2} environments

    Energy Technology Data Exchange (ETDEWEB)

    Bejarano, Paula A.; Levendis, Yiannis A. [Mechanical and Industrial Engineering, Northeastern University, Boston, MA 02115 (United States)

    2008-04-15

    A fundamental investigation has been conducted on the combustion of single particles of a bituminous coal (45-53, 75-90, and 150-180 {mu}m), of a lignite coal (45-53 and 75-90 {mu}m), and of spherical and monodisperse synthetic chars (43 {mu}m) at increasing O{sub 2} mole fractions in either N{sub 2} or CO{sub 2} balance gases. The synthetic particles were used to facilitate the observation of combustion phenomena with minimum distractions from particle-to-particle variabilities. The laboratory setup consisted of a drop-tube furnace operated at temperatures of 1400 and 1600 K. A calibrated three-color pyrometer, interfaced with the furnace, recorded luminous particle temperature-time profiles. Experimental results revealed that coal particles burned at higher mean temperatures and shorter combustion times in O{sub 2}/N{sub 2} than in O{sub 2}/CO{sub 2} environments at analogous oxygen mole fractions. In the case of the bituminous coal used herein and for the experimental combustion conditions tested, measured volatile and char temperatures as in air (21% O{sub 2}) were attained with an oxygen content in the CO{sub 2} mixtures in the neighborhood of 30%. Bituminous coal volatile and char burnout times comparable to those in air (21% O{sub 2}) were attained with oxygen content in the CO{sub 2} mixtures in the range of 30-35%. In the case of the lignite coal burned, the corresponding differences in oxygen mole fractions, which result in similar particle temperatures and burnout times in the two different gas mixtures, were less pronounced. (author)

  6. Characterizing thermogenic coalbed gas from Polish coals of different ranks by hydrous pyrolysis

    Science.gov (United States)

    Kotarba, M.J.; Lewan, M.D.

    2004-01-01

    To provide a better characterization of origin and volume of thermogenic gas generation from coals, hydrous pyrolysis experiments were conducted at 360??C for 72 h on Polish coals ranging in rank from lignite (0.3% R r) to semi-anthracite (2.0% Rr). Under these conditions, the lignites attained a medium-volatile bituminous rank (1.5% Rr), high-volatile bituminous coals attained a low-volatile bituminous rank (1.7% Rr), and the semi-anthracite obtained an anthracite rank (4.0% R r). Hydrous pyrolysis of a coal, irrespective of rank, provides a diagnostic ??13C value for its thermogenic hydrocarbon gases. This value can be used quantitatively to interpret mixing of indigenous thermogenic gas with microbial methane or exogenous thermogenic gas from other sources. Thermogenic methane quantities range from 20 dm3/kg of lignite (0.3% Rr) to 0.35 dm3/kg of semi-anthracite (2.0% Rr). At a vitrinite reflectance of 1.7% Rr, approximately 75% of the maximum potential for a coal to generate thermogenic methane has been expended. At a vitrinite reflectance of 1.7% Rr, more than 90% of the maximum potential for a coal to generate CO2 has been expended. Assuming that these quantities of generated CO2 remain associated with a sourcing coal bed as uplift or erosion provide conditions conducive for microbial methanogenesis, the resulting quantities of microbial methane generated by complete CO2 reduction can exceed the quantities of thermogenic methane generated from the same coal bed by a factor of 2-5. ?? 2004 Elsevier Ltd. All rights reserved.

  7. Intrinsic and extrinsic defects in a family of coal-derived graphene quantum dots

    Science.gov (United States)

    Singamaneni, Srinivasa Rao; van Tol, Johan; Ye, Ruquan; Tour, James M.

    2015-11-01

    In this letter, we report on the high frequency (239.2 and 336 GHz) electron spin resonance (ESR) studies performed on graphene quantum dots (GQDs), prepared through a wet chemistry route from three types of coal: (a) bituminous, (b) anthracite, and (c) coke; and from non-coal derived GQDs. The microwave frequency-, power-, and temperature-dependent ESR spectra coupled with computer-aided simulations reveal four distinct magnetic defect centers. In bituminous- and anthracite-derived GQDs, we have identified two of them as intrinsic carbon-centered magnetic defect centers (a broad signal of peak to peak width = 697 (10-4 T), g = 2.0023; and a narrow signal of peak to peak width = 60 (10-4 T), g = 2.003). The third defect center is Mn2+ (6S5/2, 3d5) (signal width = 61 (10-4 T), g = 2.0023, Aiso = 93(10-4 T)), and the fourth defect is identified as Cu2+ (2D5/2, 3d9) (g⊥ = 2.048 and g‖ = 2.279), previously undetected. Coke-derived and non-coal derived GQDs show Mn2+ and two-carbon related signals, and no Cu2+ signal. The extrinsic impurities most likely originate from the starting coal. Furthermore, Raman, photoluminescence, and ESR measurements detected no noticeable changes in the properties of the bituminous GQDs after one year. This study highlights the importance of employing high frequency ESR spectroscopy in identifying the (magnetic) defects, which are roadblocks for spin relaxation times of graphene-based materials. These defects would not have been possible to probe by other spin transport measurements.

  8. Regulation of coal polymer degradation by fungi. Tenth Quartery report, October 1996--December 1996

    Energy Technology Data Exchange (ETDEWEB)

    Irvine, R.L. [Univ. of Notre Dame, IN (United States). Dept. of Civil Engineering and Geological Sciences; Bumpus, J.A. [Univ. of Northern Iowa, Cedar Falls, IA (United States). Dept. of Chemistry

    1997-01-28

    It has long been known that low rank coal such as leonardite can be solubilized by strong base (>pH 12). Recent discoveries have also shown that leonardite is solubilized by Lewis bases at considerably lower pH values and by fungi that secrete certain Lewis bases (i.e., oxalate ion). During the current reporting period we have studied the ability of a strong base (sodium hydroxide, pH 12), and two fungi, Phanerochaete chrysosporium and Trametes versicolor, to solubilize Argonne Premium Coals. In general, Argonne Premium Coals were relatively resistant to base mediated solubilization. However, when these coals were preoxidized (150{degrees}C for seven days), substantial amounts of several coals were solubilized. Most affected were the Lewiston-Stockton bituminous coal, the Beulah-Zap lignite, the Wyodak-Anderson subbituminous coal and the Blind Canyon bituminous coal. Argonne Premium Coals were previously shown by us to be relatively resistant to solubilization by sodium oxalate. When preoxidized coals were treated with sodium oxalate, only the Beulah-Zap lignite was substantially solubilized. Although very small amounts of the other preoxidized coals were solubilized by treatment with oxalate, the small amount of solubilization that did take place was generally increased relative to that observed for coals that were not preoxidized. None of the Argonne Premium Coals were solubilized by P. chrysosporium or T. versicolor. Of considerable interest, however, is the observation that P. chrysosporium and T. versicolor mediated extensive solubilization of Lewiston-Stockton bituminous coal, the Beulah-Zap lignite and the Wyodak-Anderson subbituminous coal.

  9. Mercury in coal and the impact of coal quality on mercury emissions from combustion systems

    International Nuclear Information System (INIS)

    Kolker, Allan; Senior, Constance L.; Quick, Jeffrey C.

    2006-01-01

    The proportion of Hg in coal feedstock that is emitted by stack gases of utility power stations is a complex function of coal chemistry and properties, combustion conditions, and the positioning and type of air pollution control devices employed. Mercury in bituminous coal is found primarily within Fe-sulfides, whereas lower rank coal tends to have a greater proportion of organic-bound Hg. Preparation of bituminous coal to reduce S generally reduces input Hg relative to in-ground concentrations, but the amount of this reduction varies according to the fraction of Hg in sulfides and the efficiency of sulfide removal. The mode of occurrence of Hg in coal does not directly affect the speciation of Hg in the combustion flue gas. However, other constituents in the coal, notably Cl and S, and the combustion characteristics of the coal, influence the species of Hg that are formed in the flue gas and enter air pollution control devices. The formation of gaseous oxidized Hg or particulate-bound Hg occurs post-combustion; these forms of Hg can be in part captured in the air pollution control devices that exist on coal-fired boilers, without modification. For a given coal type, the capture efficiency of Hg by pollution control systems varies according to type of device and the conditions of its deployment. For bituminous coal, on average, more than 60% of Hg in flue gas is captured by fabric filter (FF) and flue-gas desulfurization (FGD) systems. Key variables affecting performance for Hg control include Cl and S content of the coal, the positioning (hot side vs. cold side) of the system, and the amount of unburned C in coal ash. Knowledge of coal quality parameters and their effect on the performance of air pollution control devices allows optimization of Hg capture co-benefit

  10. Development and evaluation of highly-loaded coal slurries. Phase I summary report, October 15, 1977-December 31, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Scheffee, R.S.

    1979-05-01

    Slurry fuels comprised of either bituminous, subbituminous, or lignite coal, and either aqeuous media or emulsions of No. 6 oil in water as the carrier were developed and evaluated at solids loadings up to 70% by weight. Emphasis was placed on aqueous slurries of bituminous coal. These slurries were developed for use in place of No. 6 oil in oil-fired burners. High solids loadings were attained by use of bimodal particle size distributions, which are blends of coarse-grind coal (approx. 50 to 85% -50 mesh) and fine-grind coal (generally 90% -200 mesh). The effect of the blends on slurry viscosity was determined to find the blends that minimize viscosity. The effect of mill conditions on particle size distribution was determined for each coal, using a hammermill pulverizer. A large number of water-soluble resins were evaluated for effect on slurry stability and viscosity. The best of these was found to be hydroxypropylated corn starch. Slurries based on the use of 3% solutions of the starch in water were prepared with up to 70% by weight bituminous coal and up to 65% subbituminous coal. The slurries are pourable pseudo-plastic fluids having room-temperature viscosities in the range of 550 to 1100 cp at a shear rate of 3000 sec/sup -1/, depending on the type of coal, solids loading, and particle size distribution. None of the slurries exhibited hard pack settling, even after room-temperature storage up to 74 days. Oil-in-water emulsions made with polyethylene glycol (23) lauryl ether as an emulsifier were found to be stable with respect to phase separation when stored at 160/sup 0/F. Slurries made with these emulsions do not exhibit hard pack settling after one week storage at 160/sup 0/F.

  11. A reconsideration of effect of energy scarcity on economic growth

    International Nuclear Information System (INIS)

    Uri, N.D.

    1995-01-01

    This analysis is concerned with the effect of energy scarcity on economic growth in the U.S. After defining the notion of scarcity and introducing measures of scarcity (unit costs and relative energy price), changes in the trend in resource scarcity for NG, bituminous coal, anthracite coal, and crude oil over the most recent three decades are investigated. Each of the energy resources became a significantly scarcer resource during the decade of the 1970s in the Malthusian Stock Scarcity and Malthusian Flow Scarcity sense. Unit costs exhibit a similar change for NG and crude oil but not for bituminous and anthracite coals. The situation reversed itself during the 1980s. NG, bituminous and anthracite coals, and crude oil all became significantly less scarce resources during the decade of the 1980s than they had been during the 1970s, i.e. the increase in scarcity as measured by relative energy prices observed during the decade of the 1970s was not reversed completely during the 1980s for NG and crude oil demonstrate similar patterns. Given that change has taken place, it has implications for future economic growth to the extent resource scarcity and economic growth are interrelated. To see whether this is a relevant concern, subsequent to the examination of changing resource scarcity trends, an objective effort is made to identify a long run equilibrium relationship between energy scarcity and economic growth. Relying on cointegration techniques, only for crude oil is there a suggestion that resource scarcity has affected economic growth in the U.S. over the period 1889-1992. (author)

  12. High-Functioning Wetland Formed Atop Abandoned Pavement in Eutrophic Reservoir Watershed

    Science.gov (United States)

    Clifford, C.; Heffernan, J. B.

    2017-12-01

    Water scientists and managers regularly observe how wetlands, whether natural or created, can mitigate the influence of artificial impervious surfaces on water quality. However, we rarely study or mention wetlands accidentally (sensu Palta et al. 2017) formed atop impervious surfaces. This silence occurs even though many urbanites have likely noticed sedges rimming a clogged drainage grate or in the low bits of a poorly graded or aging parking lot, or similar. A more extreme example occurs in the Little River Waterfowl Impoundment vicinity of the Butner-Falls of Neuse Game Land in Durham, North Carolina. There, a macadam road that connected local residents and a store, and served as the primary route through the area, by 1910-1920, was apparently abandoned by 1951. Later, damming nearby downstream Falls Lake Reservoir in 1981, and smaller-scale construction locally, apparently increased water table depth and flow exposure. Yet, the road remains largely intact structurally, though mostly buried and sometimes underwater. In a particularly wet segment of the road, surrounded by and partially holding back standing water even in drought, a substantial, mostly native wetland plant community has formed. This community includes trees such as overcup oak (Quercus lyrata) as large as 15 cm in diameter, shrubs such as (Cephalanthus occidentalus), sedges such as woolgrass (Scirpus cyperinus), rushes (multiple Juncus species), grasses such as wood oats (Chasmanthium latifolium), crayfish and fish, and multiple orders of herptiles. The plants grow rooted in fluffy sediment three to rarely more than 20cm deep, over solid pavement. Alongside the old road, the ditches have widened and become shallower and less surficially connected through tree roots and debris dams; they resemble pools. Sediment in these abandoned ditches has accumulated to depths of tens of centimeters, generally reforming a clay-dominated, gleyed soil, in some places buried under more tens of centimeters of very

  13. Color vision loss in patients treated with chloroquine

    Directory of Open Access Journals (Sweden)

    Ventura Dora F.

    2003-01-01

    Full Text Available Patients that make use of chloroquine or hydroxychloroquine, drugs which are frequently administered for treatment of rheumatoid arthritis, lupus erithromatosus or malaria, may suffer alterations in color vision and in contrast sensitivity. The present work evaluates the visual function of these patients in a joint study of the University of São Paulo (USP, in São Paulo, and of the Federal University of Pará (UFPA, in Belém. Thirty two chloroquine user patients without alterations in the eye fundus exam were evaluated in São Paulo (n=10; aged 38 to 71 years; mean=55,8 years and in Belém (n=22; aged 20 to 67; mean=40 years. The prescribed accumulated chloroquine dose was 45 to 430 g (mean=213 g; sd = 152 g for the São Paulo group, and 36 to 540 g (mean=174 g; sd=183 g for the Belém group. Tests were performed monocularly with corrected eye refractive state. Color discrimination was evaluated using the Cambridge Colour Test (CCT: the color discrimination threshold was measured first in the protan, deutan and tritan axes and, in succession, three MacAdam's ellipses were determined. The patient's color vision was also evaluated with color arrangement tests: the Farnsworth-Munsell 100 Hue (FM100, the Farnsworth-Munsell D15, and the Lanthony Desaturated (D15d tests. We also measured the contrast sensitivity for black-and-white sine wave grating of twenty two patients. The results were compared with controls without ophthalmologic or neuro-ophthalmologic pathologies. Twenty four patients presented acquired dyschromatopsia. There were cases of selective loss (11 patients and of diffuse loss (13 patients. Although losses were present in the FM100 there was no correlation between the FM100 error score and the ellipse area measured by the CCT. Moreover, three patients that scored normal in the FM100, failed to reach normal threshold in the CCT. The Lanthony test was less sensitive than the other two tests, since it failed to indicate loss in about

  14. Design approaches in quarrying and pit-mining reclamation

    Science.gov (United States)

    Arbogast, Belinda F.

    1999-01-01

    Reclaimed mine sites have been evaluated so that the public, industry, and land planners may recognize there are innovative designs available for consideration and use. People tend to see cropland, range, and road cuts as a necessary part of their everyday life, not as disturbed areas despite their high visibility. Mining also generates a disturbed landscape, unfortunately one that many consider waste until reclaimed by human beings. The development of mining provides an economic base and use of a natural resource to improve the quality of human life. Equally important is a sensitivity to the geologic origin and natural pattern of the land. Wisely shaping out environment requires a design plan and product that responds to a site's physiography, ecology, function, artistic form, and publication perception. An examination of selected sites for their landscape design suggested nine approaches for mining reclamation. The oldest design approach around is nature itself. Humans may sometimes do more damage going to an area in the attempt to repair it. Given enough geologic time, a small-site area, and stable adjacent ecosystems, disturbed areas recover without mankind's input. Visual screens and buffer zones conceal the facility in a camouflage approach. Typically, earth berms, fences, and plantings are used to disguise the mining facility. Restoration targets social or economic benefits by reusing the site for public amenities, most often in urban centers with large populations. A mitigation approach attempts to protect the environment and return mined areas to use with scientific input. The reuse of cement, building rubble, macadam meets only about 10% of the demand from aggregate. Recognizing the limited supply of mineral resources and encouraging recycling efforts are steps are steps in a renewable resource approach. An educative design approach effectively communicates mining information through outreach, land stewardship, and community service. Mine sites used for

  15. METHANE de-NOX for Utility PC Boilers

    Energy Technology Data Exchange (ETDEWEB)

    Bruce Bryan; Joseph Rabovitser; Serguei Nester; Stan Wohadlo

    2005-06-30

    Large-scale combustion tests with caking bituminous coal has stopped. This stoppage has come about due to limitations in current funding available to continue large scale research and development activities at Riley's Commercial Burner Test Facility (CBTF) of the PC Preheat technology. The CBTF was secured and decommissioned in the previous quarter; work this quarter has focused on disposition of PC Preheat experimental equipment at the CBTF as well as methods for disposal of about 100 tons of residual PRB test coal in storage. GTI was granted a no-cost time extension through September 2005; a final report is due in December 2005.

  16. Management of radioactive wastes in China

    International Nuclear Information System (INIS)

    Pan Ziqiang

    1994-01-01

    The policy and principles on management of radioactive wastes are stipulated. Cement solidification and bituminization unit has come into trial run. Solid radioactive waste is stored in tentative storage vault built in each of nuclear facilities. Seventeen storages associated with applications of nuclear technology and radioisotopes have been built for provinces. Disposal of low and intermediate level radioactive wastes pursues the policy of 'regional disposal'. Four repositories have been planned to be built in northwest, southwest, south and east China respectively. A program for treatment and disposal of high level radioactive waste has been made

  17. Fifth symposium on surface mining and reclamation. NCA/BCR coal conference and Expo IV

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-01-01

    The Fifth Symposium on Surface Mining and Reclamation, sponsored by the National Coal Association and Bituminous Coal Research, Inc., was held at the Kentucky Fair and Exposition Center, Louisville, Kentucky, October 18-20, 1977. Twenty-six papers from the proceedings have been entered individually into EDB and ERA. Topics covered include spoil bank revegetation, use of aerial photography, reclamation for row crop production, hydrology, computer programs related to this work, subirrigated alluvial valley floors, reclamation on steep slopes, mountain top removal, surface mine road design, successional processes involved in reclamation, land use planning, etc. (LTN)

  18. The influence of the pyrolysis conditions in a rotary oven on the characteristics of the products

    OpenAIRE

    Acevedo Muñoz, Beatriz; Barriocanal Rueda, Carmen

    2014-01-01

    The pyrolysis of 1:1 blends of reinforcing fibre (RF) from tyre wastes with low rank bituminous coal was carried out in a rotary oven. The pyrolysis conditions were modified in order to study their influence on the yield and characteristics of the char and oil obtained. The variables studied were as follows: rotation speed, final pyrolysis temperature, N2 flow and heating rate. The textural characteristics of the char were studied by means of N2 adsorption at 77 K, whereas the oil composition...

  19. Evaluation of bitumens for nuclear facilities radioactive waste immobilization

    International Nuclear Information System (INIS)

    Guzella, Marcia F.R.; Silva, Tania V. da; Loiola, Roberto; Monte, Lauro J.B.

    2000-01-01

    The activities developed at the Nuclear Technology Development Centre, Centro de Desenvolvimento da Tecnologia Nuclear - CDTN/CNEN, include the research and development work of the radioactive wastes immobilization in different kind of bitumen. The present work describes the bituminization of simulated low level wastes of evaporator concentrates.Two types of bitumen are used for incorporation of the simulated wastes generated by nuclear power plants. Studies on rheological properties, leaching data, differential thermoanalysis and water content of the waste-products have been carried out. (author)

  20. Design Constructibility Reviews.

    Science.gov (United States)

    1987-01-01

    specifications for base and sub-base courses, and wearing course.I Item 21 - Has provision been made in the specifications for positive control of the temperature...of the bituminous material? Item 22 - Test results on samples of asphalt , aggregate, sand and mix should be obtained from the plant prior to placing...in the * drawings. Item 3 - Make sure that stud types, sizes and pacinqs are spelled out in the plans and sc-i catr-. Item 4 - All welders that will