WorldWideScience

Sample records for bench-scale experiments

  1. Bench-Scale Experiments to Evaluate ERT as a Monitoring Tool for Geologic CO2 Sequestration

    Science.gov (United States)

    Breen, S. J.; Detwiler, R. L.; Carrigan, C. R.

    2010-12-01

    Field-scale studies have shown Electrical Resistivity Tomography (ERT) to be an effective tool for imaging resistivity anomalies and monitoring changing saturations in the near subsurface. Despite the challenges of implementing ERT in the deep subsurface, it has potential as a surveying technology for visualizing sequestered CO2, in part because it can be localized within the target reservoir. Currently, the technology is being evaluated as part of a geologic sequestration project in Cranfield, MS, where supercritical CO2 is injected to ten thousand feet below the surface. In support of this field-scale activity, we have designed an analog bench-scale experimental system to further evaluate the ability of ERT to quantify both the volume and spatial distribution of gas injected into a saline aquifer. Our translucent sand chambers measure 58cm x 30cm x 1cm and are lined with twenty-one stainless steel electrodes on each long side, inserted into a nonconductive plastic gasket. We fill the chamber with quartz sand with different grain sizes with a filling procedure that generates small-scale layering within the injection zone, which is overlain by a fine-grained layer that serves as a capillary barrier. Prior to gas injection, the porous medium is saturated with a low resistivity salt solution. We then inject gas into the bottom of the injection zone. Buoyant forces drive gas migration into the chamber, resulting in a combination of small-scale trapping in horizontal layers, fingering between the horizontal layers, and large-scale trapping of the gas plume along the upper capillary barrier. During pauses in gas injection, a CCD camera captures high-resolution images, and an ERT data acquisition system scans the chamber. Quantitative visualization techniques are used to process the CCD images resulting in high-resolution measurements of the spatial distribution of the injected gas. These results are directly compared to resistivity fields that result from the inversion

  2. Molten salt oxidation of mixed waste: Preliminary bench-scale experiments without radioactivity

    International Nuclear Information System (INIS)

    Haas, P.A.; Rudolph, J.C.; Bell, J.T.

    1994-06-01

    Molten salt oxidation (MSO) is a process in which organic wastes are oxidized by sparging them with air through a bed of molten sodium carbonate (bp 851 degrees C) at ≥ 900 degrees C. This process is readily applicable to the mixed waste because acidic products from Cl, S, P, etc., in the waste, along with most metals and most radionuclides, are retained within the melt as oxides or salts. Rockwell International has studied the application of MSO to various wastes, including some mixed waste. A unit used by Rockwell to study the mixed waste treatment is presently in use at Oak Ridge National Laboratory (ORNL). ORNL's studies to date have concentrated on chemical flowsheet questions. Concerns that were studied included carbon monoxide (CO) emissions, NO x , emissions, and metal retention under a variety of conditions. Initial experiments show that CO emissions increase with increasing NaCl content in the melt, increasing temperature, and increasing airflow. Carbon monoxide content is especially high (> 2000 ppm) with high chlorine content (> 10%). Thermal NO x , emissions are relatively low ( x , The metal contents of the melt and of knockout pot samples of condensed salt show high volatilities of Cs as CsCl. Average condensed salt concentrations were 60% for barium and 100% for strontium and cobalt. The cerium disappeared -- perhaps from deposition on the alumina reactor walls

  3. Investigation of mixing enhancement in porous media under helical flow conditions: 3-D bench-scale experiments

    DEFF Research Database (Denmark)

    Chiogna, Gabriele; Ye, Yu; Cirpka, Olaf A.

    2017-01-01

    Lateral mass exchange at the fringe of solute plumes is a fundamental process leading to plume dilution and reactive mixing. Mass transfer between the plume and ambient water can be considerably enhanced by helical flow occurring in three-dimensional heterogeneous anisotropic porous media [1-3]. We...... performed steady-state conservative tracer experiments in a fully three-dimensional flow-through chamber to investigate the effects of helical flow on plume spiraling and deformation, as well as on its dilution [4]. Helical flow was created by packing the porous medium in angled stripes of materials...... with different grain sizes to create blocks with macroscopically anisotropic hydraulic conductivity. The hydraulic conductivity of the blocks was varied in different experiments. Solute concentrations and flow rates were measured at high spatial resolution for samples collected at 49 outlet ports. This allowed...

  4. Electrodialytic remediation of air pollution control residues in bench scale

    DEFF Research Database (Denmark)

    Jensen, Pernille Erland; Ferreira, Celia; Hansen, Henrik K.

    2008-01-01

    Air pollution control (APC) residue from municipal solid waste incineration (MSWI) is considered a hazardous waste due to its alkalinity and high content of salts and mobile heavy metals. Various solutions for the handling of APC-residue exist in different regions; however, most commercial...... solutions are concerned with deposition. A demand for more environmentally friendly alternatives exists. Electrodialysis could be such an alternative, and the potential is being explored. This work presents a bench scale study of the feasibility of treating APC-residue from a dry system by electrodialysis....... A system resembling conventional electrodialysis was designed and adjusted to fit the high solids content feed solution (10% APC residue, 90% water). Experiments were made in bench scale with raw residue (natural pH > 12), water pre-residue (natural pH > 12), acid pre-washed residue (pH 10), and acid...

  5. BENCH SCALE SALTSTONE PROCESS DEVELOPMENT MIXING STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Cozzi, A.; Hansen, E.

    2011-08-03

    The Savannah River National Laboratory (SRNL) was requested to develop a bench scale test facility, using a mixer, transfer pump, and transfer line to determine the impact of conveying the grout through the transfer lines to the vault on grout properties. Bench scale testing focused on the effect the transfer line has on the rheological property of the grout as it was processed through the transfer line. Rheological and other physical properties of grout samples were obtained prior to and after pumping through a transfer line. The Bench Scale Mixing Rig (BSMR) consisted of two mixing tanks, grout feed tank, transfer pump and transfer hose. The mixing tanks were used to batch the grout which was then transferred into the grout feed tank. The contents of the feed tank were then pumped through the transfer line (hose) using a progressive cavity pump. The grout flow rate and pump discharge pressure were monitored. Four sampling stations were located along the length of the transfer line at the 5, 105 and 205 feet past the transfer pump and at 305 feet, the discharge of the hose. Scaling between the full scale piping at Saltstone to bench scale testing at SRNL was performed by maintaining the same shear rate and total shear at the wall of the transfer line. The results of scaling down resulted in a shorter transfer line, a lower average velocity, the same transfer time and similar pressure drops. The condition of flow in the bench scale transfer line is laminar. The flow in the full scale pipe is in the transition region, but is more laminar than turbulent. The resulting plug in laminar flow in the bench scale results in a region of no-mixing. Hence mixing, or shearing, at the bench scale should be less than that observed in the full scale, where this plug is non existent due to the turbulent flow. The bench scale tests should be considered to be conservative due to the highly laminar condition of flow that exists. Two BSMR runs were performed. In both cases, wall

  6. Bench-scale Kinetics Study of Mercury Reactions in FGD Liquors

    Energy Technology Data Exchange (ETDEWEB)

    Gary Blythe; John Currie; David DeBerry

    2008-03-31

    This document is the final report for Cooperative Agreement DE-FC26-04NT42314, 'Kinetics Study of Mercury Reactions in FGD Liquors'. The project was co-funded by the U.S. DOE National Energy Technology Laboratory and EPRI. The objective of the project has been to determine the mechanisms and kinetics of the aqueous reactions of mercury absorbed by wet flue gas desulfurization (FGD) systems, and develop a kinetics model to predict mercury reactions in wet FGD systems. The model may be used to determine optimum wet FGD design and operating conditions to maximize mercury capture in wet FGD systems. Initially, a series of bench-top, liquid-phase reactor tests were conducted and mercury species concentrations were measured by UV/visible light spectroscopy to determine reactant and byproduct concentrations over time. Other measurement methods, such as atomic absorption, were used to measure concentrations of vapor-phase elemental mercury, that cannot be measured by UV/visible light spectroscopy. Next, a series of bench-scale wet FGD simulation tests were conducted. Because of the significant effects of sulfite concentration on mercury re-emission rates, new methods were developed for operating and controlling the bench-scale FGD experiments. Approximately 140 bench-scale wet FGD tests were conducted and several unusual and pertinent effects of process chemistry on mercury re-emissions were identified and characterized. These data have been used to develop an empirically adjusted, theoretically based kinetics model to predict mercury species reactions in wet FGD systems. The model has been verified in tests conducted with the bench-scale wet FGD system, where both gas-phase and liquid-phase mercury concentrations were measured to determine if the model accurately predicts the tendency for mercury re-emissions. This report presents and discusses results from the initial laboratory kinetics measurements, the bench-scale wet FGD tests, and the kinetics modeling

  7. Lab and Bench-Scale Pelletization of Torrefied Wood Chips

    DEFF Research Database (Denmark)

    Shang, Lei; Nielsen, Niels Peter K.; Stelte, Wolfgang

    2013-01-01

    content, additive addition, and the degree of torrefaction on the pelletizing properties and pellet quality, i.e., density, static friction, and pellet strength. Results were compared with pellet production using a bench-scale pelletizer. The results indicate that friction is the key factor when scaling...... up from single-pellet press to bench-scale pelletizer. Tuning moisture content or increasing the die temperature did not ease the pellet production of torrefied wood chips significantly. The addition of rapeseed oil as a lubricant reduced the static friction by half and stabilized pellet production...

  8. Bench scale flotation of spodume/quartz and lepidolite/quartz synthetic mixtures

    International Nuclear Information System (INIS)

    Valadao, G.E.S.; Gontijo, C.F.; Peres, A.E.C.

    1985-01-01

    Based on results of zeta potential determinations and microflotation tests, bench scale flotation experiments were carried out using spodume/quartz and lepodolite/quartz synthetic mixtures. Pure natural samples, further purified in laboratory, and commercial reagents were employed. The minerals were characterized by X-ray diffraction technique. Selectivity between spodume and quartz was achieved through modification with corn starch and between lepidolite and quartz through pH control in the acidic range. (Author) [pt

  9. Recycling of polyethene and polypropene in a novel bench-scale rotating cone reactor by high temperature pyrolysis.

    NARCIS (Netherlands)

    Westerhout, R.W.J.; Westerhout, R.W.J.; Waanders, J.; Kuipers, J.A.M.; van Swaaij, Willibrordus Petrus Maria

    1998-01-01

    The high-temperature pyrolysis of polyethene (PE), polypropene (PP), and mixtures of these polymers was studied in a novel bench-scale rotating cone reactor (RCR). Experiments showed that the effect of the sand or reactor temperature on the product spectrum obtained is large compared to the effect

  10. In situ remediation of hexavalent chromium with pyrite fines : bench scale demonstration

    International Nuclear Information System (INIS)

    Cathum, S.; Wong, W.P.; Brown, C.E.

    2002-01-01

    An in situ remediation technique for chromium contaminated soil with pyrite fines was presented. Past industrial activities and lack of disposal facilities have contributed to a serious problem dealing with chromium, which cannot be eliminated from the environment because it is an element. Both bench-scale and laboratory testing was conducted to confirm the efficiency of the proposed process which successfully converted Cr(VI) into Cr(III) in soil and water. Cr(III) is less toxic and immobile in the environment compared to Cr(VI) which moves freely in the soil matrix, posing a risk to the groundwater quality. pH in the range of 2.0 to 7.6 has no effect on the reactivity of pyrite towards Cr(VI). The optimization of the bench-scale treatment resulted in a large volume of chromium waste, mostly from the control experiments and column hydrology testing. These waste streams were treated according to municipal guidelines before disposal to the environment. Samples of chromium waste before and after treatment were analyzed. Cr (VI) was completely mineralized to below guideline levels. It was determined that several conditions, including contact time between pyrite and Cr(VI), are crucial for complete mineralization of Cr(VI). 13 refs., 8 tabs., 9 figs

  11. Bench-Scale Demonstration of Hot-Gas Desulfurization Technology

    International Nuclear Information System (INIS)

    Portzer, Jeffrey W.; Gangwal, Santosh K.

    1997-01-01

    Prior to the current project, development of the DSRP was done in a laboratory setting, using synthetic gas mixtures to simulate the regeneration off-gas and coal gas feeds. The objective of the current work is to further the development of zinc titanate fluidized-bed desulfurization (ZTFBD) and the DSRP for hot-gas cleanup by testing with actual coal gas. The objectives of this project are to: (1) Develop and test an integrated, skid-mounted, bench-scale ZTFBD/DSRP reactor system with a slipstream of actual coal gas; (2) Test the bench-scale DSRP over an extended period with a slipstream of actual coal gas to quantify the degradation in performance, if any, caused by the trace contaminants present in coal gas (including heavy metals, chlorides, fluorides, and ammonia); (3) Expose the DSRP catalyst to actual coal gas for extended periods and then test its activity in a laboratory reactor to quantify the degradation in performance, if any, caused by static exposure to the trace contaminants in coal gas; (4) Design and fabricate a six-fold larger-scale DSRP reactor system for future slipstream testing; (5) Further develop the fluidized-bed DSRP to handle high concentrations (up to 14 percent) of SO 2 that are likely to be encountered when pure air is used for regeneration of desulfurization sorbents; and (6) Conduct extended field testing of the 6X DSRP reactor with actual coal gas and high concentrations of SO 2 . The accomplishment of the first three objectives--testing the DSRP with actual coal gas, integration with hot-gas desulfurization, and catalyst exposure testing--was described previously (Portzer and Gangwal, 1994, 1995; Portzer et al., 1996). This paper summarizes the results of previous work and describes the current activities and plans to accomplish the remaining objectives

  12. A bench-scale biotreatability methodology to evaluate field bioremediation

    International Nuclear Information System (INIS)

    Saberiyan, A.G.; MacPherson, J.R. Jr.; Moore, R.; Pruess, A.J.; Andrilenas, J.S.

    1995-01-01

    A bench-scale biotreatability methodology was designed to assess field bioremediation of petroleum contaminated soil samples. This methodology was performed successfully on soil samples from more than 40 sites. The methodology is composed of two phases, characterization and experimentation. The first phase is physical, chemical, and biological characterization of the contaminated soil sample. This phase determines soil parameters, contaminant type, presence of indigenous contaminant-degrading bacteria, and bacterial population size. The second phase, experimentation, consists of a respirometry test to measure the growth of microbes indirectly (via generation of CO 2 ) and the consumption of their food source directly (via contaminant loss). Based on a Monod kinetic analysis, the half-life of a contaminant can be calculated. Abiotic losses are accounted for based on a control test. The contaminant molecular structure is used to generate a stoichiometric equation. The stoichiometric equation yields a theoretical ratio for mg of contaminant degraded per mg of CO 2 produced. Data collected from the respirometry test are compared to theoretical values to evaluate bioremediation feasibility

  13. Oxygen-controlled Biosurfactant Production in a Bench Scale Bioreactor

    Science.gov (United States)

    de Kronemberger, Frederico Araujo; Anna, Lidia Maria Melo Santa; Fernandes, Ana Carolina Loureiro Brito; de Menezes, Reginaldo Ramos; Borges, Cristiano Piacsek; Freire, Denise Maria Guimarães

    Rhamnolipids have been pointed out as promising biosurfactants. The most studied microorganisms for the aerobic production of these molecules are the bacteria of the genus Pseudomonas. The aim of this work was to produce a rhamnolipid-type biosurfactant in a bench-scale bioreactor by one strain of Pseudomonas aeruginosa isolated from oil environments. To study the microorganism growth and production dependency on oxygen, a nondispersive oxygenation device was developed, and a programmable logic controller (PLC) was used to set the dissolved oxygen (DO) concentration. Using the data stored in a computer and the predetermined characteristics of the oxygenation device, it was possible to evaluate the oxygen uptake rate (OUR) and the specific OUR (SOUR) of this microorganism. These rates, obtained for some different DO concentrations, were then compared to the bacterial growth, to the carbon source consumption, and to the rhamnolipid and other virulence factors production. The SOUR presented an initial value of about 60.0 mg02/gdw h. Then, when the exponential growth phase begins, there is a rise in this rate. After that, the SOUR reduces to about 20.0 mg02/gdw h. The carbon source consumption is linear during the whole process.

  14. 100 Area groundwater biodenitrification bench-scale treatability study procedures

    Energy Technology Data Exchange (ETDEWEB)

    Peyton, B.M.; Martin, K.R.

    1993-05-01

    This document describes the methodologies and procedures for conducting the bench-scale biodenitrification treatability tests at Pacific Northwest Laboratory{sup a} (PNL). Biodenitrification is the biological conversion of nitrate and nitrite to gaseous nitrogen. The tests will use statistically designed batch studies to determine if biodenitrification can reduce residual nitrate concentrations to 45 mg/L, the current maximum contaminant level (MCL). These tests will be carried out in anaerobic flasks with a carbon source added to demonstrate nitrate removal. At the pilot scale, an incremental amount of additional carbon will be required to remove the small amount of oxygen present in the incoming groundwater. These tests will be conducted under the guidance of Westinghouse Hanford Company (WHC) and the 100-HR-3 Groundwater Treatability Test Plan (DOE/RL-92-73) and the Treatability Study Program Plan (DOE/RL-92-48) using groundwater from 100-HR-3. In addition to the procedures, requirements for safety, quality assurance, reporting, and schedule are given. Appendices include analytical procedures, a Quality Assurance Project Plan, a Health and Safety Plan, and Applicable Material Data Safety Sheets. The procedures contained herein are designed specifically for the 100-HR-3 Groundwater Treatability Test Plan, and while the author believes that the methods described herein are scientifically valid, the procedures should not be construed or mistaken to be generally applicable to any other treatability study.

  15. Design of a Compact and Versatile Bench Scale Tubular Reactor

    Directory of Open Access Journals (Sweden)

    R. Prasad

    2009-06-01

    Full Text Available A compact and versatile laboratory tubular reactor has been designed and fabricated keeping in view of reducing capital cost and minimising energy consumption for gas/vapor-phase heterogeneous catalytic reactions. The reactor is consisted of two coaxial corning glass tubes with a helical coil of glass tube in between the coaxial tubes serving as vaporiser and pre-heater, the catalyst bed is in the inner tube. A schematic diagram of the reactor with detailed dimensions and working principles are described. The attractive feature of the reactor is that the vaporiser, pre-heater and fixed bed reactor are merged in a single compact unit. Thus, the unit minimises separate vaporiser and pre-heater, also avoids separate furnaces used for them and eliminate auxiliary instrumentation such as temperature controller etc. To demonstrate the system operation and illustrate the key features, catalyst screening data and the efficient collection of complete, and accurate intrinsic kinetic data are provided for oxidation of CO over copper chromite catalyst. CO oxidation is an important reaction for auto-exhaust pollution control. The suitability of the versatile nature of the reactor has been ascertained for catalytic reactions where either volatile or vaporizable feeds can be introduced to the reaction zone, e.g. oxidation of iso-octane, reduction of nitric oxide, dehydrogenation of methanol, ethanol and iso-propanol, hydrogenation of nitrobenzene to aniline, etc. Copyright (c 2009 by BCREC. All Rights reserved.[Received: 10 February 2009, Accepted: 9 May 2009][How to Cite: R. Prasad, G. Rattan. (2009. Design of a Compact and Versatile Bench Scale Tubular Reactor. Bulletin of Chemical Reaction Engineering and Catalysis, 4(1: 5-9.  doi:10.9767/bcrec.4.1.1250.5-9][How to Link/ DOI: http://dx.doi.org/10.9767/bcrec.4.1.1250.5-9

  16. Bench scale demonstration and conceptual engineering for DETOXSM catalyzed wet oxidation

    International Nuclear Information System (INIS)

    Moslander, J.; Bell, R.; Robertson, D.; Dhooge, P.; Goldblatt, S.

    1994-01-01

    Laboratory and bench scale studies of the DETOX SM catalyzed wet oxidation process have been performed with the object of developing the process for treatment of hazardous and mixed wastes. Reaction orders, apparent rates, and activation energies have been determined for a range of organic waste surrogates. Reaction intermediates and products have been analyzed. Metals' fates have been determined. Bench scale units have been designed, fabricated, and tested with solid and liquid organic waste surrogates. Results from the laboratory and bench scale studies have been used to develop conceptual designs for application of the process to hazardous and mixed wastes

  17. Pyrolysis of automotive shredder residue in a bench scale rotary kiln.

    Science.gov (United States)

    Notarnicola, Michele; Cornacchia, Giacinto; De Gisi, Sabino; Di Canio, Francesco; Freda, Cesare; Garzone, Pietro; Martino, Maria; Valerio, Vito; Villone, Antonio

    2017-07-01

    Automotive shredder residue (ASR) can create difficulties when managing, with its production increasing. It is made of different type of plastics, foams, elastomers, wood, glasses and textiles. For this reason, it is complicated to dispose of in a cost effective way, while also respecting the stringent environmental restrictions. Among thermal treatments, pyrolysis seems to offer an environmentally attractive method for the treatment of ASR; it also allows for the recovery of valuable secondary materials/fuels such as pyrolysis oils, chars, and gas. While, there is a great deal of significant research on ASR pyrolysis, the literature on higher scale pyrolysis experiments is limited. To improve current literature, the aim of the study was to investigate the pyrolysis of ASR in a bench scale rotary kiln. The Italian ASR was separated by dry-sieving into two particle size fractions: d30mm. Both the streams were grounded, pelletized and then pyrolyzed in a continuous bench scale rotary kiln at 450, 550 and 650°C. The mass flow rate of the ASR pellets was 200-350g/h and each test ran for about 4-5h. The produced char, pyrolysis oil and syngas were quantified to determine product distribution. They were thoroughly analyzed with regard to their chemical and physical properties. The results show how higher temperatures increase the pyrolysis gas yield (44wt% at 650°C) as well as its heating value. The low heating value (LHV) of syngas ranges between 18 and 26MJ/Nm 3 dry. The highest pyrolysis oil yield (33wt.%) was observed at 550°C and its LHV ranges between 12.5 and 14.5MJ/kg. Furthermore, only two out of the six produced chars respect the LHV limit set by the Italian environmental regulations for landfilling. The obtained results in terms of product distribution and their chemical-physical analyses provide useful information for plant scale-up. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Bauman, R.F.; Coless, L.A.; Davis, S.M. [and others

    1995-12-31

    In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263. Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.

  19. Bench-scale treatability studies for simulated incinerator scrubber blowdown containing radioactive cesium and strontium

    International Nuclear Information System (INIS)

    Coroneos, A.C.; Taylor, P.A.; Arnold, W.D. Jr.; Bostick, D.A.; Perona, J.J.

    1994-12-01

    The purpose of this report is to document the results of bench-scale testing completed to remove 137 Cs and 90 Sr from the Oak Ridge K-25 Site Toxic Substances Control Act (TSCA) Incinerator blowdown at the K-25 Site Central Neutralization Facility, a wastewater treatment facility designed to remove heavy metals and uranium from various wastewaters. The report presents results of bench-scale testing using chabazite and clinoptilolite zeolites to remove cesium and strontium; using potassium cobalt ferrocyanide (KCCF) to remove cesium; and using strontium chloride coprecipitation, sodium phosphate coprecipitation, and calcium sulfate coprecipitation to remove strontium. Low-range, average-range, and high-range concentration blowdown surrogates were used to complete the bench-scale testing

  20. Bench-Scale Process for Low-Cost Carbon Dioxide (CO2) Capture Using a Phase-Changing Absorbent

    Energy Technology Data Exchange (ETDEWEB)

    Westendorf, Tiffany; Caraher, Joel; Chen, Wei; Farnum, Rachael; Perry, Robert; Spiry, Irina; Wilson, Paul; Wood, Benjamin

    2015-03-31

    The objective of this project is to design and build a bench-scale process for a novel phase-changing aminosilicone-based CO2-capture solvent. The project will establish scalability and technical and economic feasibility of using a phase-changing CO2-capture absorbent for post-combustion capture of CO2 from coal-fired power plants with 90% capture efficiency and 95% CO2 purity at a cost of $40/tonne of CO2 captured by 2025 and a cost of <$10/tonne of CO2 captured by 2035. In the first budget period of this project, the bench-scale phase-changing CO2 capture process was designed using data and operating experience generated under a previous project (ARPA-e project DE-AR0000084). Sizing and specification of all major unit operations was completed, including detailed process and instrumentation diagrams. The system was designed to operate over a wide range of operating conditions to allow for exploration of the effect of process variables on CO2 capture performance.

  1. Treatment of Synthetic Wastewater Containing AB14 Pigment by Electrooxidation in both Pilot and Bench Scale Reactors

    Directory of Open Access Journals (Sweden)

    Jalal Basiri parsa

    2016-01-01

    Full Text Available The electrochemical oxidation process was used for the degradation of Acid Brown 14 in both bench and pilot scale reactors. The bench scale one with a working volume of 0.5 L was equipped with platinum plate used as the anode and stainless steel (SS-304 plates as the cathode. The pilot scale reactor had a volume of 9 L and was equipped with SS-304 plates used as both the anode and the cathode. Experiments were run using these reactors to investigate the two parameters of energy consumption and anode efficiency. The bench scale reactor was capable of removing 92% and 36% of the dye and COD, respectively, after 18 min of operation. The pilot scale reactor, however, was capable of removing 87% and 59% of the dye and the COD content, respectively, after 60 min of operation. The kinetic study of both the bench and pilot reactors for dye and COD removals showed that both processes followed a zero order kinetic.

  2. Cometabolic biotreatment of TCE-contaminated groundwater: Laboratory and bench-scale development studies

    International Nuclear Information System (INIS)

    Donaldson, T.L.; Jennings, H.L.; Lucero, A.J.; Strandberg, G.W.; Morris, M.I.; Palumbo, A.V.; Boerman, P.A.; Tyndall, R.L.

    1992-01-01

    The Oak Ridge National Laboratory is conducting a demonstration of two cometabolic technologies for biotreatment of groundwater contaminated with trichloroethylene (TCE) and other organics. Technologies based on methanotrophic (methane-utilizing) and toluene-degrading microorganisms will be compared side-by-side on the same groundwater stream. Laboratory and bench-scale bioreactor studies have been conducted to guide selection of microbial cultures and operating conditions for the field demonstration. This report presents the results of the laboratory and bench-scale studies for the methanotrophic system

  3. Bench scale demonstration of the Supermethanol concept : The synthesis of methanol from glycerol derived syngas

    NARCIS (Netherlands)

    van Bennekom, J. G.; Venderbosch, R. H.; Assink, D.; Lemmens, K. P. J.; Heeres, H. J.

    2012-01-01

    An integrated process for the synthesis of methanol from aqueous glycerol involving reforming of the feed to syngas followed by methanol synthesis is successfully demonstrated in a continuous bench scale unit. Glycerol reforming was carried out at pressures of 24-27 MPa and temperatures of 948-998 K

  4. DEGRADATION OF POLYNUCLEAR AROMATIC HYDROCARBONS UNDER BENCH-SCALE COMPOST CONDITIONS

    Science.gov (United States)

    The relationship between biomass growth and degradation of polynuclear aromatic hydrocarbons (PAHs) in soil, and subsequent toxicity reduction, was evaluated in 10 in-vessel, bench-scale compost units. Field soil was aquired from the Reilly Tar and Chemical Company Superfund site...

  5. Development of continuous bench scale unit for direct liquefaction

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Wang Lai [Korea Inst. of Energy and Resources, Daeduk (Korea, Republic of)

    1995-12-31

    Batch coal liquefaction experiments using tubing bombs and continuous experiments by cell liquefaction test facility were carried out. The main purpose was to maximize the coal liquefaction yields by improving the activity of coal dissolution catalysts which are oil soluble transition metal naphthenate and to supplement the incomplete research results. In the meantime, the study on the reaction characteristics of coal liquefaction and coal liquid upgrading catalyst upon sulfiding conditions and phosphorous addition have been conducted (author). 102 refs., 35 figs.

  6. Bench-scale arc melter for R&D in thermal treatment of mixed wastes

    Energy Technology Data Exchange (ETDEWEB)

    Kong, P.C.; Grandy, J.D.; Watkins, A.D.; Eddy, T.L.; Anderson, G.L.

    1993-05-01

    A small dc arc melter was designed and constructed to run bench-scale investigations on various aspects of development for high-temperature (1,500-1,800{degrees}C) processing of simulated transuranic-contaminated waste and soil located at the Radioactive Waste Management Complex (RWMC). Several recent system design and treatment studies have shown that high-temperature melting is the preferred treatment. The small arc melter is needed to establish techniques and procedures (with surrogates) prior to using a similar melter with the transuranic-contaminated wastes in appropriate facilities at the site. This report documents the design and construction, starting and heating procedures, and tests evaluating the melter`s ability to process several waste types stored at the RWMC. It is found that a thin graphite strip provides reliable starting with initial high current capability for partially melting the soil/waste mixture. The heating procedure includes (1) the initial high current-low voltage mode, (2) a low current-high voltage mode that commences after some slag has formed and arcing dominates over the receding graphite conduction path, and (3) a predominantly Joule heating mode during which the current can be increased within the limits to maintain relatively quiescent operation. Several experiments involving the melting of simulated wastes are discussed. Energy balance, slag temperature, and electrode wear measurements are presented. Recommendations for further refinements to enhance its processing capabilities are identified. Future studies anticipated with the arc melter include waste form processing development; dissolution, retention, volatilization, and collection for transuranic and low-level radionuclides, as well as high vapor pressure metals; electrode material development to minimize corrosion and erosion; refractory corrosion and/or skull formation effects; crucible or melter geometry; metal oxidation; and melt reduction/oxidation (redox) conditions.

  7. Bench-scale and full-scale studies of nitric oxides reduction by gaseous fuel reburning

    International Nuclear Information System (INIS)

    Su, S.; Xiang, J.; Sun, L.S.; Hu, S.; Zhu, J.M.

    2008-01-01

    Nitrogen oxides (NOx) emissions from coal-fired boilers are significant contributors to atmospheric pollution. China has specified more rigorous legal limits for NOx emissions from power plants. As a result of the need to reduce NOx emissions, cost-effective NOx reduction strategies must be explored. This paper presented detailed experimental studies on a gaseous fuel reburning process that was performed in a 36 kilowatt bench-scale down-fired furnace to define the optimal reburning operating conditions when different Chinese coals were fired in the furnace. In addition, the combustion system of a 350 megawatt full-scale boiler was retrofitted according to the experimental results. Finally, the gaseous fuel reburning was applied to the retrofitted full-scale boiler. The purpose of the study was to obtain a better understanding of the influence of the key parameters on nitric oxide (NO) reduction efficiency of the reburning process and demonstrate the gaseous fuel reburning on a 350 MWe coal-fired boiler in China. The paper described the experimental procedure with particular reference to the experimental facility and measurement; a schematic diagram of the experimental system; experimental fuels; and characteristics of coals for the reburning experiments. Results that were presented included influence of reburn zone residence time; influence of gaseous reburn fuel per cent; influence of excess air coefficient; and unburned carbon in fly ash. It was concluded that both an above 50 per cent NO reduction efficiency and low carbon loss can be obtained by the gaseous fuel reburning process under the optimal operating conditions. 20 refs., 5 tabs., 10 figs

  8. Bench-scale arc melter for R ampersand D in thermal treatment of mixed wastes

    International Nuclear Information System (INIS)

    Kong, P.C.; Grandy, J.D.; Watkins, A.D.; Eddy, T.L.; Anderson, G.L.

    1993-05-01

    A small dc arc melter was designed and constructed to run bench-scale investigations on various aspects of development for high-temperature (1,500-1,800 degrees C) processing of simulated transuranic-contaminated waste and soil located at the Radioactive Waste Management Complex (RWMC). Several recent system design and treatment studies have shown that high-temperature melting is the preferred treatment. The small arc melter is needed to establish techniques and procedures (with surrogates) prior to using a similar melter with the transuranic-contaminated wastes in appropriate facilities at the site. This report documents the design and construction, starting and heating procedures, and tests evaluating the melter's ability to process several waste types stored at the RWMC. It is found that a thin graphite strip provides reliable starting with initial high current capability for partially melting the soil/waste mixture. The heating procedure includes (1) the initial high current-low voltage mode, (2) a low current-high voltage mode that commences after some slag has formed and arcing dominates over the receding graphite conduction path, and (3) a predominantly Joule heating mode during which the current can be increased within the limits to maintain relatively quiescent operation. Several experiments involving the melting of simulated wastes are discussed. Energy balance, slag temperature, and electrode wear measurements are presented. Recommendations for further refinements to enhance its processing capabilities are identified. Future studies anticipated with the arc melter include waste form processing development; dissolution, retention, volatilization, and collection for transuranic and low-level radionuclides, as well as high vapor pressure metals; electrode material development to minimize corrosion and erosion; refractory corrosion and/or skull formation effects; crucible or melter geometry; metal oxidation; and melt reduction/oxidation (redox) conditions

  9. Performance of a bench-scale fast fluidized bed carbonator

    DEFF Research Database (Denmark)

    Pathi, Sharat Kumar; Lin, Weigang; Illerup, Jytte Boll

    2014-01-01

    by applying a new experimental method with accurate control of the particle recirculation rate. The experimental results show that the inlet calcium to carbon molar ratio is the main factor on the CO2 capture efficiency in the carbonator, that is, increasing the inlet Ca/C from 4 to 13 results in increasing...... is estimated from experiments under stable operating conditions with constant bed inventory, reactor temperature and exit CO2 concentration. The validated CFB carbonator model was used to simulate different operating conditions relevant for CO2 capture from a power plant and from a cement plant. The results...... the CO2 capture efficiency from 40 to 85% with limestone having a maximum CO2 capture capacity of only 11.5%. Furthermore, a reactor model for a carbonator is developed based on the Kunii-Levenspiels model. A key parameter in the model is the particle distribution along the height of the reactor, which...

  10. An integrated testing facility for bench scale catalyst research

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, H.D.; Hogan, R.J.; McMurtrie, D.E.

    1983-08-01

    Discovering new catalysts and designing new catalytic processes has long been hindered by equipment that is either designed for hand operation with the data acquisition functions in some stage of automation or is patterned after refinery installations to smaller, pilot plant like facilities. The latter approach has required large vessels (and hence large amounts of experimental catalyst and feedstocks) to be used or the use of improperly fitted control equipment with constant attention to the operation of a small reactor system. Constant attention partially negates the intent of the automation effort. Results from some of these systems are often unsatisfactory because of poor material balances and control. The data from some schemes must then be manually transferred into other databases for use in reports, correlations, etc. An earlier paper from this laboratory (1) described an initial attempt to provide a reliable, reproducible method for more productive catalyst screening, but that system still lacked an automatic data management system and was not flexible with regards to wide range changes of pressure and flow. Also, several different types of experiments could not be run concurrently. Recently, several schemes have appeared (2-6) which deal with distributed systems as they apply to various laboratory and pilot plant operations. This paper describes an automated system that allows for up to 21 reactors to be in operation concurrently with a staff of five people. All units are independently run without normal operator intervention and the system is designed fail safe for unattended operation. It has been used extensively for screening exploratory catalysts, catalytic process optimization, kinetic modeling and increasingly in refinery process optimization.

  11. Bench Scale Process for Low Cost CO2 Capture Using a Phase-Changing Absorbent: Final Scientific/Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Westendorf, Tiffany [GE Global Research, Niskayuna, New York (United States); Buddle, Stanlee [GE Global Research, Niskayuna, New York (United States); Caraher, Joel [GE Global Research, Niskayuna, New York (United States); Chen, Wei [GE Global Research, Niskayuna, New York (United States); Doherty, Mark [GE Global Research, Niskayuna, New York (United States); Farnum, Rachel [GE Global Research, Niskayuna, New York (United States); Giammattei, Mark [GE Global Research, Niskayuna, New York (United States); Hancu, Dan [GE Global Research, Niskayuna, New York (United States); Miebach, Barbara [GE Global Research, Niskayuna, New York (United States); Perry, Robert [GE Global Research, Niskayuna, New York (United States); Rubinsztajn, Gosia; Spiry, Irina; Wilson, Paul; Wood, Benjamin

    2017-05-31

    The objective of this project is to design and build a bench-scale process for a novel phase-changing aminosilicone-based CO2-capture solvent. The project will establish scalability and technical and economic feasibility of using a phase-changing CO2-capture absorbent for post-combustion capture of CO2 from coal-fired power plants. The U.S. Department of Energy’s goal for Transformational Carbon Capture Technologies is the development of technologies available for demonstration by 2025 that can capture 90% of emitted CO2 with at least 95% CO2 purity for less than $40/tonne of CO2 captured. In the first budget period of the project, the bench-scale phase-changing CO2 capture process was designed using data and operating experience generated under a previous project (ARPA-e project DE-AR0000084). Sizing and specification of all major unit operations was completed, including detailed process and instrumentation diagrams. The system was designed to operate over a wide range of operating conditions to allow for exploration of the effect of process variables on CO2 capture performance. In the second budget period of the project, individual bench-scale unit operations were tested to determine the performance of each of each unit. Solids production was demonstrated in dry simulated flue gas across a wide range of absorber operating conditions, with single stage CO2 conversion rates up to 75mol%. Desorber operation was demonstrated in batch mode, resulting in desorption performance consistent with the equilibrium isotherms for GAP-0/CO2 reaction. Important risks associated with gas humidity impact on solids consistency and desorber temperature impact on thermal degradation were explored, and adjustments to the bench-scale process were made to address those effects. Corrosion experiments were conducted to support selection of suitable materials of construction for the major

  12. Design and fabrication of a glovebox for the Plasma Hearth Process radioactive bench-scale system

    International Nuclear Information System (INIS)

    Wahlquist, D.R.

    1996-01-01

    This paper presents some of the design considerations and fabrication techniques for building a glovebox for the Plasma Hearth Process (PHP) radioactive bench-scale system. The PHP radioactive bench-scale system uses a plasma torch to process a variety of radioactive materials into a final vitrified waste form. The processed waste will contain plutonium and trace amounts of other radioactive materials. The glovebox used in this system is located directly below the plasma chamber and is called the Hearth Handling Enclosure (HHE). The HHE is designed to maintain a confinement boundary between the processed waste and the operator. Operations that take place inside the HHE include raising and lowering the hearth using a hydraulic lift table, transporting the hearth within the HHE using an overhead monorail and hoist system, sampling and disassembly of the processed waste and hearth, weighing the hearth, rebuilding a hearth, and sampling HEPA filters. The PHP radioactive bench-scale system is located at the TREAT facility at Argonne National Laboratory-West in Idaho Falls, Idaho

  13. Embedded Sensors and Controls to Improve Component Performance and Reliability -- Bench-scale Testbed Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Melin, Alexander M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kisner, Roger A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Drira, Anis [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Reed, Frederick K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-09-01

    Embedded instrumentation and control systems that can operate in extreme environments are challenging due to restrictions on sensors and materials. As a part of the Department of Energy's Nuclear Energy Enabling Technology cross-cutting technology development programs Advanced Sensors and Instrumentation topic, this report details the design of a bench-scale embedded instrumentation and control testbed. The design goal of the bench-scale testbed is to build a re-configurable system that can rapidly deploy and test advanced control algorithms in a hardware in the loop setup. The bench-scale testbed will be designed as a fluid pump analog that uses active magnetic bearings to support the shaft. The testbed represents an application that would improve the efficiency and performance of high temperature (700 C) pumps for liquid salt reactors that operate in an extreme environment and provide many engineering challenges that can be overcome with embedded instrumentation and control. This report will give details of the mechanical design, electromagnetic design, geometry optimization, power electronics design, and initial control system design.

  14. Bench-scale evaluation of drinking water treatment parameters on iron particles and water quality.

    Science.gov (United States)

    Rahman, M Safiur; Gagnon, Graham A

    2014-01-01

    Discoloration of water resulting from suspended iron particles is one of the main customer complaints received by water suppliers. However, understanding of the mechanisms of discoloration as well as role of materials involved in the process is limited. In this study, an array of bench scale experiments were conducted to evaluate the impact of the most common variables (pH, PO4, Cl2 and DOM) on the properties of iron particles and suspensions derived from the oxygenation of Fe(II) ions in NaHCO3 buffered synthetic water systems. The most important factors as well as their rank influencing iron suspension color and turbidity formation were identified for a range of water quality parameters. This was accomplished using a 2(4) full factorial design approach at a 95% confidence level. The statistical analysis revealed that phosphate was found to be the most significant factor to alter color (contribution: 37.9%) and turbidity (contribution: 45.5%) in an iron-water system. A comprehensive study revealed that phosphate and chlorine produced iron suspension with reduced color and turbidity, made ζ-potential more negative, reduced the average particle size, and increased iron suspension stability. In the presence of DOM, color was observed to increase but a reverse trend was observed to decrease the turbidity and to alter particle size distribution. HPSEC results suggest that higher molecular weight fractions of DOM tend to adsorb onto the surfaces of iron particles at early stages, resulting in alteration of the surface charge of iron particles. This in turn limits particles aggregation and makes iron colloids highly stable. In the presence of a phosphate based corrosion inhibitor, this study demonstrated that color and turbidity resulting from suspended iron were lower at a pH value of 6.5 (compared to pH of 8.5). The same trend was observed in presence of DOM. This study also suggested that iron colloid suspension color and turbidity in chlorinated drinking water

  15. Accumulation of uranium, cesium, and radium by microbial cells: bench-scale studies

    International Nuclear Information System (INIS)

    Strandberg, G.W.; Shumate, S.E. II.

    1982-07-01

    This report describes bench-scale studies on the utilization of microbial cells for the concentration and removal of uranium, radium, and cesium from nuclear processing waste streams. Included are studies aimed at elucidating the basic mechanism of uranium uptake, process development efforts for the use of a combined denitrification-uranium removal process to treat a specific nuclear processing waste stream, and a preliminary investigation of the applicability of microorganisms for the removal of 137 Cs and 226 Ra from existing waste solutions

  16. From a single pellet press to a bench scale pellet mill - Pelletizing six different biomass feedstocks

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Shang, Lei; Sárossy, Zsuzsa

    2016-01-01

    The increasing demand for biomass pellets requires the investigation of alternative raw materials for pelletizetion. In the present paper, the pelletization process of fescue, alfalfa, sorghum, triticale, miscanthus and willow is studied to determine if results obtained in a single pellet press...... (SPP) can be extrapolated to larger scale pellet mills. The single pellet press was used to find the optimum moisture content and die operating temperature for pellet production. Then, these results were compared with those obtained from a bench-scale pellet mill. A moisture content of around 10 wt...

  17. Bench-Scale Silicone Process for Low-Cost CO{sub 2} Capture

    Energy Technology Data Exchange (ETDEWEB)

    Wood, Benjamin; Genovese, Sarah; Perry, Robert; Spiry, Irina; Farnum, Rachael; Sing, Surinder; Wilson, Paul; Buckley, Paul; Acharya, Harish; Chen, Wei; McDermott, John; Vipperia, Ravikumar; Yee, Michael; Steele, Ray; Fresia, Megan; Vogt, Kirk

    2013-12-31

    A bench-scale system was designed and built to test an aminosilicone-based solvent. A model was built of the bench-scale system and this model was scaled up to model the performance of a carbon capture unit, using aminosilicones, for CO{sub 2} capture and sequestration (CCS) for a pulverized coal (PC) boiler at 550 MW. System and economic analysis for the carbon capture unit demonstrates that the aminosilicone solvent has significant advantages relative to a monoethanol amine (MEA)-based system. The CCS energy penalty for MEA is 35.9% and the energy penalty for aminosilicone solvent is 30.4% using a steam temperature of 395 °C (743 °F). If the steam temperature is lowered to 204 °C (400 °F), the energy penalty for the aminosilicone solvent is reduced to 29%. The increase in cost of electricity (COE) over the non-capture case for MEA is ~109% and increase in COE for aminosilicone solvent is ~98 to 103% depending on the solvent cost at a steam temperature of 395 °C (743 °F). If the steam temperature is lowered to 204 °C (400 °F), the increase in COE for the aminosilicone solvent is reduced to ~95-100%.

  18. Production of uranium hexafluoride by the catalysed fluorox process: pilot plant and supporting bench-scale studies

    International Nuclear Information System (INIS)

    Janov, J.; Charlton, B.G.; LePage, A.H.; Vilkaitis, V.K.

    1982-04-01

    The feasibility of producing UF 6 by the catalysed reaction of UF 4 with oxygen (the Fluorox process) was investigated in a 150 mm diameter fluidised bed reactor and in supporting bench-scale experiments. The rate of the Fluorox reaction in batch experiments was increased by an order of magnitude with 1 to 5 per cent catalyst (containing 3 to 4 per cent platinum on alumina). The maximum UF 6 production rate at 650 deg. C was 0.9 kg h -1 . However, the platinum catalyst was completely poisoned after production of only 1 and 20 kg UF 6 per kg of catalyst when using respectively French and British UF 4 . Regeneration of the catalyst was demonstrated to be technically feasible by washing with water or ammonium oxalate solution or treating with hydrogen and hydrogen fluoride at 350-650 deg. C. However, since the very fast rate of poisoning would necessitate higher catalyst concentrations and/or frequent regeneration, the catalysed Fluorox process in unlikely to be economically competitive with the direct fluorination of UF 4

  19. Bench-scale study of active mine water treatment using cement kiln dust (CKD) as a neutralization agent.

    Science.gov (United States)

    Mackie, Allison L; Walsh, Margaret E

    2012-02-01

    The overall objective of this study was to investigate the potential impact on settled water quality of using cement kiln dust (CKD), a waste by-product, to replace quicklime in the active treatment of acidic mine water. Bench-scale experiments were conducted to evaluate the treatment performance of calcium hydroxide (Ca(OH)(2)) slurries generated using four different CKD samples compared to a control treatment with quicklime (CaO) in terms of reducing acidity and metals concentrations in acid mine drainage (AMD) samples taken from the effluent of a lead/zinc mine in Atlantic Canada. Results of the study showed that all of the CKD samples evaluated were capable of achieving greater than 97% removal of total zinc and iron. The amount of solid alkaline material required to achieve pH targets required for neutralization of the AMD was found to be higher for treatment with the CKD slurries compared to the quicklime slurry control experiments, and varied linearly with the free lime content of the CKD. The results of this study also showed that a potential benefit of treating mine water with CKD could be reduced settled sludge volumes generated in the active treatment process, and further research into the characteristics of the sludge generated from the use of CKD-generated calcium hydroxide slurries is recommended. Copyright © 2011 Elsevier Ltd. All rights reserved.

  20. PNNL Report on the Development of Bench-scale CFD Simulations for Gas Absorption across a Wetted Wall Column

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Chao; Xu, Zhijie; Lai, Canhai; Whyatt, Greg A.; Marcy, Peter; Gattiker, J. R.; Sun, Xin

    2016-05-01

    This report is prepared for the demonstration of hierarchical prediction of carbon capture efficiency of a solvent-based absorption column. A computational fluid dynamics (CFD) model is first developed to simulate the core phenomena of solvent-based carbon capture, i.e., the CO2 physical absorption and chemical reaction, on a simplified geometry of wetted wall column (WWC) at bench scale. Aqueous solutions of ethanolamine (MEA) are commonly selected as a CO2 stream scrubbing liquid. CO2 is captured by both physical and chemical absorption using highly CO2 soluble and reactive solvent, MEA, during the scrubbing process. In order to provide confidence bound on the computational predictions of this complex engineering system, a hierarchical calibration and validation framework is proposed. The overall goal of this effort is to provide a mechanism-based predictive framework with confidence bound for overall mass transfer coefficient of the wetted wall column (WWC) with statistical analyses of the corresponding WWC experiments with increasing physical complexity.

  1. The hot bench scale plant Ester for the vitrification of high level wastes

    International Nuclear Information System (INIS)

    Nannicini, R.; Strazzer, A.; Cantale, C; Donato, A.; Grossi, G.

    1985-01-01

    In this paper the hot bench-scale plant ESTER for the vitrification of the high-level radioactive wastes is described, and the main results of the first radioactive campaign are reported. The ESTER plant, which is placed in the ADECO-ESSOR hot cells of the C.C.R.-EURATOM-ISPRA, has been built and is operated by the ENEA, Departement of Fuel Cycle. It began operating with real radioactive wastes about 1 year ago, solidifying a total of 12 Ci of fission products into 2,02 Kg of borosilicate glass, corresponding to 757 ml of glass. During the vitrification many samples of liquid and gaseous streams have been taken and analyzed. A radioactivity balance in the plant has been calculated, as well as a mass balance of nitrates and of the 137 Cs and 106 Ru volatized in the process

  2. Final PHP bench-scale report for the DOE-ID/SAIC sole source contract

    International Nuclear Information System (INIS)

    1997-04-01

    The Plasma Hearth Process (PHP) Technology Development Project was established to develop, test, and evaluate a new concept for treating mixed waste. The new concept uses direct current (dc) transferred-arc plasma torch technology to process mixed waste into a glass-like end-product. Under the cognizance of the US Department of Energy (DOE) Office of Technology Development (OTD) Mixed Waste Focus Area (MWFA), the technology is being explored for its potential to treat mixed waste. Because it is a mature technology, well-understood and commercially available, it is expected to develop rapidly in this new application. This report summarizes the radioactive bench-scale system activities funded under PHP Sole Source Contract DE-AC07-94ID13266 through the end of the contract

  3. BENCH-SCALE STEAM REFORMING OF ACTUAL TANK 48H WASTE

    Energy Technology Data Exchange (ETDEWEB)

    Burket, P; Gene Daniel, G; Charles Nash, C; Carol Jantzen, C; Michael Williams, M

    2008-09-25

    Fluidized Bed Steam Reforming (FBSR) has been demonstrated to be a viable technology to remove >99% of the organics from Tank 48H simulant, to remove >99% of the nitrate/nitrite from Tank 48H simulant, and to form a solid product that is primarily carbonate based. The technology was demonstrated in October of 2006 in the Engineering Scale Test Demonstration Fluidized Bed Steam Reformer1 (ESTD FBSR) at the Hazen Research Inc. (HRI) facility in Golden, CO. The purpose of the Bench-scale Steam Reformer (BSR) testing was to demonstrate that the same reactions occur and the same product is formed when steam reforming actual radioactive Tank 48H waste. The approach used in the current study was to test the BSR with the same Tank 48H simulant and same Erwin coal as was used at the ESTD FBSR under the same operating conditions. This comparison would allow verification that the same chemical reactions occur in both the BSR and ESTD FBSR. Then, actual radioactive Tank 48H material would be steam reformed in the BSR to verify that the actual tank 48H sample reacts the same way chemically as the simulant Tank 48H material. The conclusions from the BSR study and comparison to the ESTD FBSR are the following: (1) A Bench-scale Steam Reforming (BSR) unit was successfully designed and built that: (a) Emulated the chemistry of the ESTD FBSR Denitration Mineralization Reformer (DMR) and Carbon Reduction Reformer (CRR) known collectively as the dual reformer flowsheet. (b) Measured and controlled the off-gas stream. (c) Processed real (radioactive) Tank 48H waste. (d) Met the standards and specifications for radiological testing in the Savannah River National Laboratory (SRNL) Shielded Cells Facility (SCF). (2) Three runs with radioactive Tank 48H material were performed. (3) The Tetraphenylborate (TPB) was destroyed to > 99% for all radioactive Bench-scale tests. (4) The feed nitrate/nitrite was destroyed to >99% for all radioactive BSR tests the same as the ESTD FBSR. (5) The

  4. Bench scale testing of micronized magnetite beneficiation. Quarterly technical progress report 4, October--December, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Anast, K.

    1994-01-25

    This project is aimed at development of a process that, by using ultra fine magnetite suspension, would expand the application of heavy media separation technology to processing fine, {minus}28 mesh coals. These coal fines, produced during coal mining and crushing, are separated in the conventional coal preparation plant and generally impounded in a tailings pond. Development of an economic process for processing these fines into marketable product will expand the utilization of coal for power production in an environmentally acceptable and economically viable way. This process has been successfully researched at PETC but has not been studied on a continuous bench-scale unit, which is a necessary step towards commercial development of this promising technology. The goal of the program is to investigate the technology in a continuous circuit at a reasonable scale to provide a design basis for larger plants and a commercial feasibility data.

  5. Bench-scale testing of a micronized magnetite, fine-coal cleaning process

    Energy Technology Data Exchange (ETDEWEB)

    Suardini, P.J. [Custom Coals, International, Pittsburgh, PA (United States)

    1995-11-01

    Custom Coals, International has installed and is presently testing a 500 lb/hr. micronized-magnetite, fine-coal cleaning circuit at PETC`s Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program`s, High Efficiency Preparation Subprogram. The project includes design, construction, testing, and decommissioning of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense medium cycloning of the 300 by 30 micron feed coal using a nominal minus 10 micron size magnetite medium, and medium recovery using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

  6. Performance evaluation of the DCMD desalination process under bench scale and large scale module operating conditions

    KAUST Repository

    Francis, Lijo

    2014-04-01

    The flux performance of different hydrophobic microporous flat sheet commercial membranes made of poly tetrafluoroethylene (PTFE) and poly propylene (PP) was tested for Red Sea water desalination using the direct contact membrane distillation (DCMD) process, under bench scale (high δT) and large scale module (low δT) operating conditions. Membranes were characterized for their surface morphology, water contact angle, thickness, porosity, pore size and pore size distribution. The DCMD process performance was optimized using a locally designed and fabricated module aiming to maximize the flux at different levels of operating parameters, mainly feed water and coolant inlet temperatures at different temperature differences across the membrane (δT). Water vapor flux of 88.8kg/m2h was obtained using a PTFE membrane at high δT (60°C). In addition, the flux performance was compared to the first generation of a new locally synthesized and fabricated membrane made of a different class of polymer under the same conditions. A total salt rejection of 99.99% and boron rejection of 99.41% were achieved under extreme operating conditions. On the other hand, a detailed water characterization revealed that low molecular weight non-ionic molecules (ppb level) were transported with the water vapor molecules through the membrane structure. The membrane which provided the highest flux was then tested under large scale module operating conditions. The average flux of the latter study (low δT) was found to be eight times lower than that of the bench scale (high δT) operating conditions.

  7. Uncertainty Quantification Analysis of Both Experimental and CFD Simulation Data of a Bench-scale Fluidized Bed Gasifier

    Energy Technology Data Exchange (ETDEWEB)

    Shahnam, Mehrdad [National Energy Technology Lab. (NETL), Morgantown, WV (United States). Research and Innovation Center, Energy Conversion Engineering Directorate; Gel, Aytekin [ALPEMI Consulting, LLC, Phoeniz, AZ (United States); Subramaniyan, Arun K. [GE Global Research Center, Niskayuna, NY (United States); Musser, Jordan [National Energy Technology Lab. (NETL), Morgantown, WV (United States). Research and Innovation Center, Energy Conversion Engineering Directorate; Dietiker, Jean-Francois [West Virginia Univ. Research Corporation, Morgantown, WV (United States)

    2017-10-02

    Adequate assessment of the uncertainties in modeling and simulation is becoming an integral part of the simulation based engineering design. The goal of this study is to demonstrate the application of non-intrusive Bayesian uncertainty quantification (UQ) methodology in multiphase (gas-solid) flows with experimental and simulation data, as part of our research efforts to determine the most suited approach for UQ of a bench scale fluidized bed gasifier. UQ analysis was first performed on the available experimental data. Global sensitivity analysis performed as part of the UQ analysis shows that among the three operating factors, steam to oxygen ratio has the most influence on syngas composition in the bench-scale gasifier experiments. An analysis for forward propagation of uncertainties was performed and results show that an increase in steam to oxygen ratio leads to an increase in H2 mole fraction and a decrease in CO mole fraction. These findings are in agreement with the ANOVA analysis performed in the reference experimental study. Another contribution in addition to the UQ analysis is the optimization-based approach to guide to identify next best set of additional experimental samples, should the possibility arise for additional experiments. Hence, the surrogate models constructed as part of the UQ analysis is employed to improve the information gain and make incremental recommendation, should the possibility to add more experiments arise. In the second step, series of simulations were carried out with the open-source computational fluid dynamics software MFiX to reproduce the experimental conditions, where three operating factors, i.e., coal flow rate, coal particle diameter, and steam-to-oxygen ratio, were systematically varied to understand their effect on the syngas composition. Bayesian UQ analysis was performed on the numerical results. As part of Bayesian UQ analysis, a global sensitivity analysis was performed based on the simulation results, which shows

  8. Hydrogen generation from bioethanol reforming : bench-scale unit performance with Cu/Nb2O5 catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Machado, N.R.C.F.; Rizzo, R.C.P.; Calsavara, V.; Takahashi, F.; Almeida, A.A.; Melo, F.R. de; Zschornack, M.A.; Bessani, A.N.; Rodrigues, R.M.O. [State University of Maringa, Maringa (Brazil). Dept. of Chemical Engineering Lab. of Catalysis; Schmal, M. [Cidade Universitaria, Rio de Janeiro (Brazil). Centro de Tecnologia, Graduate School and Research in Engineering Alberto Luiz Coimbra Institute; Cantao, M.P. [Institute of Technology for Development, Curitiba (Brazil). Dept. of Materials

    2003-07-01

    A series of experiments have been conducted to produce hydrogen from ethanol reforming. This paper presents the bench-scale study unit that uses a 5 per cent copper-niobium2oxygen5 (Cu/Nb2O5) catalyst previously selected in a micro reactor. X-ray diffraction analysis revealed that the catalyst contained copper oxide in an amorphous form and that the Nb2O5 was highly crystalline. The calcinated catalyst was analysed with X-ray photoelectron spectroscopy and showed that 35 per cent of total copper was on the surface as Cu{sup I} (55 per cent) and Cu{sup II} (45 per cent). The surface area was mainly comprised of meso and macro pores. There was a two-step reduction of Cu{sup II} to Cu at 245 and 306 degrees C, as shown by temperature programmed reduction, as well as a 6 per cent reduction of Nb2O5. An internal reactor with 16 grams (g) of catalyst pellets was contained in the reaction unit. To optimize hydrogen production, reaction temperature and feed rate were varied, and the major by-product was carbon dioxide. Reagents (water and ethanol) were fed into and vaporized in, an electric pre-heater in stoichiometric proportion. Mean conversion increased from 17 per cent to 35 per cent through an increase of reaction temperature from 300 to 400 degrees C. Minor by-products were detected in the form of ethene and ethyl ether. 9 refs., 3 tabs., 4 figs.

  9. 100 Area soil washing: Bench scale tests on 116-F-4 pluto crib soil

    Energy Technology Data Exchange (ETDEWEB)

    Field, J.G.

    1994-06-10

    The Pacific Northwest Laboratory conducted a bench-scale treatability study on a pluto crib soil sample from 100 Area of the Hanford Site. The objective of this study was to evaluate the use of physical separation (wet sieving), treatment processes (attrition scrubbing, and autogenous surface grinding), and chemical extraction methods as a means of separating radioactively-contaminated soil fractions from uncontaminated soil fractions. The soil washing treatability study was conducted on a soil sample from the 116-F-4 Pluto Crib that had been dug up as part of an excavation treatability study. Trace element analyses of this soil showed no elevated concentrations above typically uncontaminated soil background levels. Data on the distribution of radionuclide in various size fractions indicated that the soil-washing tests should be focused on the gravel and sand fractions of the 116-F-4 soil. The radionuclide data also showed that {sup 137}Cs was the only contaminant in this soil that exceeded the test performance goal (TPG). Therefore, the effectiveness of subsequent soil-washing tests for 116-F-4 soil was evaluated on the basis of activity attenuation of {sup 137}Cs in the gravel- and sand-size fractions.

  10. Performance of Dolomite Calcination in a Bench-Scale Rotary Kiln

    Directory of Open Access Journals (Sweden)

    Wulandari Winny

    2018-01-01

    Full Text Available Dolomite calcination is one of process steps to prepare calcined dolomite for raw materials in magnesium production. Calcination of dolomite involves heating the raw material at sufficient temperature in order to release the carbon dioxide from its carbonate minerals. This process is commonly conducted in a rotary kiln. There have been a number of calcination studies in a laboratory scale, but the study of dolomite calcination in a larger scale is very scarce. This research is aimed to study the performance of dolomite calcination in a bench-scale rotary kiln with 500 gram of feed. The effect of various parameters, including temperatures, feed rate, rotating frequency, and particle size were examined. The temperature of rotary kiln was varied between 700 and 1000 °C, while the particle size of dolomite was varied between 0.149 – 0.297 mm and up to 10 – 15 mm. The temperature distribution inside the rotary kiln was also measured. It is obtained that a conversion of 92% was attained at operation temperature of 1000 °C, which is at a higher temperature compared to the laboratory scale, where a conversion of 100% was obtained at 900 °C. This imply that the effect of heat transfer also plays important role in the calcination of dolomite especially at a larger scale.

  11. Bench-scale demonstration of treatment technologies for contaminated sediments in Sydney Tar Ponds

    International Nuclear Information System (INIS)

    Volchek, K.; Velicogna, D.; Punt, M.; Wong, B.; Weimer, L.; Tsangaris, A.; Brown, C.E.

    2003-01-01

    A series of bench-scale tests were conducted to determine the capabilities of selected commercially available technologies for treating contaminated sediments from the South Pond of Sydney Tar Ponds. This study was conducted under the umbrella of a technology demonstration program aimed at evaluating technologies to be used in the remediation of such sediments. The following approach was proposed by SAIC Canada for the treatment of the sediments: (1) solvent extraction for the removal of organic contaminants, (2) acid/chelant leaching for the removal of inorganic contaminants such as heavy metals, and (3) plasma hearth process for the destruction of toxic streams resulting from the first two processes. Solvent extraction followed by plasma treatment proved effective for removing and destroying organic contaminants. The removal of metals did not achieve the expected results through leaching. An approach was proposed for treating those sediments based on the results of the study. The approach differed depending on the level of organic content. An assessment of associated process costs for both a pilot-scale field demonstration and a full-scale treatment was provided. 11 tabs., 4 figs

  12. Destruction of chemical agent simulants in a supercritical water oxidation bench-scale reactor

    International Nuclear Information System (INIS)

    Veriansyah, Bambang; Kim, Jae-Duck; Lee, Jong-Chol

    2007-01-01

    A new design of supercritical water oxidation (SCWO) bench-scale reactor has been developed to handle high-risk wastes resulting from munitions demilitarization. The reactor consists of a concentric vertical double wall in which SCWO reaction takes place inside an inner tube (titanium grade 2, non-porous) whereas pressure resistance is ensured by a Hastelloy C-276 external vessel. The performances of this reactor were investigated with two different kinds of chemical warfare agent simulants: OPA (a mixture of isopropyl amine and isopropyl alcohol) as the binary precursor for nerve agent of sarin and thiodiglycol [TDG (HOC 2 H 4 ) 2 S] as the model organic sulfur heteroatom. High destruction rates based on total organic carbon (TOC) were achieved (>99.99%) without production of chars or undesired gases such as carbon monoxide and methane. The carbon-containing product was carbon dioxide whereas the nitrogen-containing products were nitrogen and nitrous oxide. Sulfur was totally recovered in the aqueous effluent as sulfuric acid. No corrosion was noticed in the reactor after a cumulative operation time of more than 250 h. The titanium tube shielded successfully the pressure vessel from corrosion

  13. Treatment studies of plutonium-bearing INEEL waste surrogates in a bench-scale arc furnace

    International Nuclear Information System (INIS)

    Freeman, C.J.

    1997-05-01

    Since 1989, the Subsurface Disposal Area (SDA) at the Idaho National Environmental and Engineering Laboratory (INEEL) has been included on the National Priority List for remediation. Arc- and plasma-heated furnaces are being considered for converting the radioactive mixed waste buried in the SDA to a stabilized-vitreous form. Nonradioactive, surrogate SDA wastes have been melted during tests in these types of furnaces, but data are needed on the behavior of transuranic (TRU) constituents, primarily plutonium, during thermal treatment. To begin collecting this data, plutonium-spiked SDA surrogates were processed in a bench-scale arc furnace to quantify the fate of the plutonium and other hazardous and nonhazardous metals. Test conditions included elevating the organic, lead, chloride, and sodium contents of the surrogates. Blends having higher organic contents caused furnace power levels to fluctuate. An organic content corresponding to 50% INEEL soil in a soil-waste blend was the highest achievable before power fluctuations made operating conditions unacceptable. The glass, metal, and off-gas solids produced from each surrogate blend tested were analyzed for elemental (including plutonium) content and the partitioning of each element to the corresponding phase was calculated

  14. Domestic Wastewater Reuse in Concrete Using Bench-Scale Testing and Full-Scale Implementation

    Directory of Open Access Journals (Sweden)

    Ayoup M. Ghrair

    2016-08-01

    Full Text Available Demand for fresh water by the construction sector is expected to increase due to the high increase in the growth of construction activities in Jordan. This study aims to evaluate the potential of scale-up of the application of treated domestic wastewater in concrete from bench-scale to a full-scale. On the lab scale, concrete and mortar mixes using Primary and Secondary Treated Wastewater (PTW, STW and Distilled Water (DW were cast and tested after various curing ages (7, 28, 120, and 200 days. Based on wastewater quality, according to IS 456-2000, the STW is suitable for mortar and concrete production. Mortar made with STW at curing time up to 200 days has no significant negative effect on the mortar’s compressive strength. Conversely, the PTW exceeded the maximum permissible limits of total organic content and E coli. for concrete mixing-water. Using PTW results, a significant increase in the initial setting time of up to 16.7% and a decrease in the concrete workability are observed. In addition, using PTW as mixing water led to a significant reduction in the compressive strength up to 19.6%. The results that came out from scaling up to real production operation of ready-mix concrete were in harmony with the lab-scale results.

  15. Safety analysis of the CSTR-1 bench-scale coal liquefaction unit

    Energy Technology Data Exchange (ETDEWEB)

    Hulburt, D.A.

    1981-05-01

    The objective of the program reported herein was to provide a Safety Analysis of the CSTR-1 bench scale unit located in Building 167 at the Pittsburgh Energy Technology Center. It was apparent that considerable effort was expended in the design and construction of the unit, and in the development of operating procedures, with regard to safety. Exhaust ventilation, H/sub 2/ and H/sub 2/S monitoring, overpressure protection, overtemperature protection, and interlock systems have been provided. Present settings on the pressure and temperature safety systems are too high, however, to insure prevention of vessel deformation or damage in all cases. While the occurrence of catastrophic rupture of a system pressure vessel (e.g., reactor, high pressure separators) is unlikely, the potential consequences to personnel are severe. Feasibility of providing shielding for these components should be considered. A more probable mode of vessel failure in the event of overpressure or overtemperature and failure of the safety system is yielding of the closure bolts followed by high pressure flow across the mating surfaces. As a minimum, shielding should be designed to restrict travel of resultant spray. The requirements for personal protective equipment are presently stated in rather broad and general terms in the operating procedures. Safe practices and procedures would be more assured if specific requirements were stated and included for each operational step. Recommendations were developed for all hazards triggered by the guidelines.

  16. Bench-Scale Evaluation of Hydrothermal Processing Technology for Conversion of Wastewater Solids to Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Marrone, Philip A.; Elliott, Douglas C.; Billing, Justin M.; Hallen, Richard T.; Hart, Todd R.; Kadota, Paul; Moeller, Jeff C.; Randel, Margaaret A.; Schmidt, Andrew J.

    2018-04-01

    Hydrothermal Liquefaction (HTL) and Catalytic Hydrothermal Gasification (CHG) proof-of-concept bench-scale tests were performed to assess the potential of hydrothermal treatment for handling municipal wastewater sludge. HTL tests were conducted at 300-350°C and 20 MPa on three different feeds: primary sludge, secondary sludge, and digested solids. Corresponding CHG tests were conducted at 350°C and 20 MPa on the HTL aqueous phase output using a ruthenium based catalyst. Biocrude yields ranged from 25-37%. Biocrude composition and quality were comparable to biocrudes generated from algae feeds. Subsequent hydrotreating of biocrude resulted in a product with comparable physical and chemical properties to crude oil. CHG product gas methane yields on a carbon basis ranged from 47-64%. Siloxane concentrations in the CHG product gas were below engine limits. The HTL-CHG process resulted in a chemical oxygen demand (COD) reduction of > 99.9% and a reduction in residual solids for disposal of 94-99%.

  17. Hierarchical calibration and validation for modeling bench-scale solvent-based carbon capture. Part 1: Non-reactive physical mass transfer across the wetted wall column: Original Research Article: Hierarchical calibration and validation for modeling bench-scale solvent-based carbon capture

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Chao [Physical and Computational Sciences Directorate, Pacific Northwest National Laboratory, Richland WA; Xu, Zhijie [Physical and Computational Sciences Directorate, Pacific Northwest National Laboratory, Richland WA; Lai, Canhai [Physical and Computational Sciences Directorate, Pacific Northwest National Laboratory, Richland WA; Whyatt, Greg [Pacific Northwest National Laboratory, Energy and Environment Directorate, Richland WA; Marcy, Peter [Statistical Sciences Group, Los Alamos National Laboratory, Los Alamos NM; Sun, Xin [Physical and Computational Sciences Directorate, Pacific Northwest National Laboratory, Richland WA

    2017-04-27

    A hierarchical model calibration and validation is proposed for quantifying the confidence level of mass transfer prediction using a computational fluid dynamics (CFD) model, where the solvent-based carbon dioxide (CO2) capture is simulated and simulation results are compared to the parallel bench-scale experimental data. Two unit problems with increasing level of complexity are proposed to breakdown the complex physical/chemical processes of solvent-based CO2 capture into relatively simpler problems to separate the effects of physical transport and chemical reaction. This paper focuses on the calibration and validation of the first unit problem, i.e. the CO2 mass transfer across a falling ethanolamine (MEA) film in absence of chemical reaction. This problem is investigated both experimentally and numerically using nitrous oxide (N2O) as a surrogate for CO2. To capture the motion of gas-liquid interface, a volume of fluid method is employed together with a one-fluid formulation to compute the mass transfer between the two phases. Bench-scale parallel experiments are designed and conducted to validate and calibrate the CFD models using a general Bayesian calibration. Two important transport parameters, e.g. Henry’s constant and gas diffusivity, are calibrated to produce the posterior distributions, which will be used as the input for the second unit problem to address the chemical adsorption of CO2 across the MEA falling film, where both mass transfer and chemical reaction are involved.

  18. Bench-Scale Development of a Hot Carbonate Absorption Process with Crystallization-Enabled High-Pressure Stripping for Post-Combustion CO{sub 2} Capture

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yongqi; DeVries, Nicholas; Ruhter, David; Manoranjan, Sahu; Ye, Qing; Ye, Xinhuai; Zhang, Shihan; Chen, Scott; Li, Zhiwei; O' Brien, Kevin

    2014-03-31

    A novel Hot Carbonate Absorption Process with Crystallization-Enabled High-Pressure Stripping (Hot-CAP) has been developed by the University of Illinois at Urbana-Champaign and Carbon Capture Scientific, LLC in this three-year, bench-scale project. The Hot-CAP features a concentrated carbonate solution (e.g., K{sub 2}CO{sub 3}) for CO{sub 2} absorption and a bicarbonate slurry (e.g., KHCO{sub 3}) for high-pressure CO{sub 2} stripping to overcome the energy use and other disadvantages associated with the benchmark monoethanolamine (MEA) process. The project was aimed at performing laboratory- and bench-scale experiments to prove its technical feasibility and generate process engineering and scale-up data, and conducting a techno-economic analysis (TEA) to demonstrate its energy use and cost competitiveness over MEA. To meet project goals and objectives, a combination of experimental, modeling, process simulation, and economic analysis studies were applied. Carefully designed and intensive experiments were conducted to measure thermodynamic and reaction engineering data relevant to four major unit operations in the Hot-CAP (i.e., CO{sub 2} absorption, CO{sub 2} stripping, bicarbonate crystallization, and sulfate reclamation). The rate promoters that could accelerate the CO{sub 2} absorption rate into the potassium carbonate/bicarbonate (PCB) solution to a level greater than that into the 5 M MEA solution were identified, and the superior performance of CO{sub 2} absorption into PCB was demonstrated in a bench-scale packed-bed column. Kinetic data on bicarbonate crystallization were developed and applied for crystallizer design and sizing. Parametric testing of high-pressure CO{sub 2} stripping with concentrated bicarbonate-dominant slurries at high temperatures ({>=}140{degrees}C) in a bench-scale stripping column demonstrated lower heat use than with MEA. The feasibility of a modified process for combining SO{sub 2} removal with CO{sub 2} capture was preliminarily

  19. Environmental data from laboratory- and bench-scale Pressurized Fluidized-Bed Hydroretorting of Eastern oil shale

    Energy Technology Data Exchange (ETDEWEB)

    Mensinger, M.C.; Rue, D.M.; Roberts, M.J.

    1991-01-01

    As part of a 3-year program to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) Process for Eastern oil shales, IGT conducted tests in laboratory-scale batch and continuous units as well as a 45-kg/h bench-scale unit to generate a data base for 6 Eastern shales. Data were collected during PFH processing of raw Alabama and Indiana shales and a beneficiated Indiana shale for environmental mitigation analyses. The data generated include trace element analyses of the raw feeds and spent shales, product oils, and sour waters. The sulfur compounds present in the product gas and trace components in the sour water were also determined. In addition, the leaching characteristics of the feed and residue solids were determined. The data obtained were used to evaluate the environmental impact of a shale processing plant based on the PFH process. This paper presents the environmental data obtained from bench-scale tests conducted during the program.

  20. Environmental data from laboratory- and bench-scale Pressurized Fluidized-Bed Hydroretorting of Eastern oil shale

    Energy Technology Data Exchange (ETDEWEB)

    Mensinger, M.C.; Rue, D.M.; Roberts, M.J.

    1991-12-31

    As part of a 3-year program to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) Process for Eastern oil shales, IGT conducted tests in laboratory-scale batch and continuous units as well as a 45-kg/h bench-scale unit to generate a data base for 6 Eastern shales. Data were collected during PFH processing of raw Alabama and Indiana shales and a beneficiated Indiana shale for environmental mitigation analyses. The data generated include trace element analyses of the raw feeds and spent shales, product oils, and sour waters. The sulfur compounds present in the product gas and trace components in the sour water were also determined. In addition, the leaching characteristics of the feed and residue solids were determined. The data obtained were used to evaluate the environmental impact of a shale processing plant based on the PFH process. This paper presents the environmental data obtained from bench-scale tests conducted during the program.

  1. A novel bench-scale column assay to investigate site-specific nitrification biokinetics in biological rapid sand filters

    DEFF Research Database (Denmark)

    Tatari, Karolina; Smets, Barth F.; Albrechtsen, Hans-Jørgen

    2013-01-01

    A bench-scale assay was developed to obtain site-specific nitrification biokinetic information from biological rapid sand filters employed in groundwater treatment. The experimental set-up uses granular material subsampled from a full-scale filter, packed in a column, and operated with controlled...... and continuous hydraulic and ammonium loading. Flowrates and flow recirculation around the column are chosen to mimic full-scale hydrodynamic conditions, and minimize axial gradients. A reference ammonium loading rate is calculated based on the average loading experienced in the active zone of the full......-scale filter. Effluent concentrations of ammonium are analyzed when the bench-scale column is subject to reference loading, from which removal rates are calculated. Subsequently, removal rates above the reference loading are measured by imposing short-term loading variations. A critical loading rate...

  2. Results of bench-scale plasma system testing in support of the Plasma Hearth Process

    International Nuclear Information System (INIS)

    Leatherman, G.L.; Cornelison, C.; Frank, S.

    1996-01-01

    The Plasma Hearth Process (PHP) is a high-temperature process that destroys hazardous organic components and stabilizes the radioactive components and hazardous metals in a leach-resistant vitreous slag waste form. The PHP technology development program is targeted at mixed waste that cannot be easily treated by conventional means. For example, heterogeneous debris, which may contain hazardous organics, toxic metals, and radionuclides, is difficult to characterize and cannot be treated with conventional thermal, chemical, or physical treatment methods. A major advantage of the PHP over other plasma processes is its ability to separate nonradioactive, non-hazardous metals from the non-metallic and radioactive components which are contained in the vitreous slag. The overall PHP program involves the design, fabrication, and operation of test hardware to demonstrate and certify that the PHP concept is viable for DOE waste treatment. The program involves bench-scale testing of PHP equipment in radioactive service, as well as pilot-scale demonstration of the PHP concept using nonradioactive, surrogate test materials. The fate of secondary waste streams is an important consideration for any technology considered for processing mixed waste. The main secondary waste stream generated by the PHP is flyash captured by the fabric- filter baghouse. The PHP concept is that flyash generated by the process can, to a large extent, be treated by processing this secondary waste stream in the PHP. Prior to the work presented in the paper, however, the PHP project has not quantitatively demonstrated the ability to treat PHP generated flyash. A major consideration is the quantity of radionuclides and RCRA-regulated metals in the flyash that can be retained the resultant waste form

  3. Bench-Scale Silicone Process for Low-Cost CO{sub 2} Capture

    Energy Technology Data Exchange (ETDEWEB)

    Fresia, Megan; Vogt, Kirk

    2013-12-31

    GE Global Research is developing technology to remove carbon dioxide (CO{sub 2}) from the flue gas of coal-fired power plants. A mixture of 3-aminopropyl end-capped polydimethylsiloxane (GAP-1m) and triethylene glycol (TEG) is the preferred CO{sub 2} capture solvent. GE Global Research was contracted by the Department of Energy to test a bench-scale continuous CO{sub 2} absorption/desorption system using a GAP-1m/TEG mixture as the solvent. SiVance LLC was sub-contracted to provide the GAP-1m material and conduct an Environmental, Health, and Safety (EH&S) assessment for a 550 MW coal-fired power plant. Five components of the solvent, CAS#2469-55-8 (GAP-0), CAS#106214-84-0 (GAP-1-4), TEG, and methanol and xylene (minor contaminants from the aminosilicone) are included in this assessment. One by-product, GAP-1m/SOX salt, and dodecylbenzenesulfonic acid (DDBSA) were also identified for analysis. All of the solvent components and DDBSA are listed on the EPA’s TSCA Inventory allowing companies to manufacture and use the chemicals commercially. The toxicological effects of each component were defined, and control mechanisms necessary to comply with U.S. EH&S regulations are summarized. An engineering and control system, including environmental abatement, was described for minimizing exposure and release of the chemical components. Proper handling and storage recommendations are made for each chemical to minimize risk to workers and the surrounding community.

  4. Technical Approach for In Situ Biological Treatment Research: Bench- Scale Experiments

    Science.gov (United States)

    1993-08-01

    cultures derived from ferulic acid-degrading sewage sludge enrichments (Grbic-Galic and Vogel 1987). These cultures utilize exogenously supplied CO2 for...GAC reactor. They observed bioregeneration of the carbon media through desorption of adsorbed phenol and subsequent biogas production . They found that...the contribution of biogas production , adsorption, and biomass production were all important In the removal of phenol. 88 238. Speitel et al. (1989

  5. Experience gained in bench scale and pilot scale fluidised bed processing

    CSIR Research Space (South Africa)

    Hadley, TD

    2005-01-01

    Full Text Available , considerable progress has been made. The earliest developments were in coal combustion. This was formalised in the formation of the NFBC boiler in the early 1980’s for the investigation of utilising discard and duff coals. Work has been done on in-bed sulphur...

  6. Experience gained in pilot-scale and bench-scale fluidised beds processing

    CSIR Research Space (South Africa)

    Hadley, TD

    2006-02-01

    Full Text Available , considerable progress has been made. The earliest developments were in coal combustion. Work has been done on in-bed sulphur capture to reduce the sulphur dioxide off-gas content. Expertise in the design and commissioning of industrial-scale plants has led...

  7. Performance study of protective clothing against hot water splashes: from bench scale test to instrumented manikin test.

    Science.gov (United States)

    Lu, Yehu; Song, Guowen; Wang, Faming

    2015-03-01

    Hot liquid hazards existing in work environments are shown to be a considerable risk for industrial workers. In this study, the predicted protection from fabric was assessed by a modified hot liquid splash tester. In these tests, conditions with and without an air spacer were applied. The protective performance of a garment exposed to hot water spray was investigated by a spray manikin evaluation system. Three-dimensional body scanning technique was used to characterize the air gap size between the protective clothing and the manikin skin. The relationship between bench scale test and manikin test was discussed and the regression model was established to predict the overall percentage of skin burn while wearing protective clothing. The results demonstrated strong correlations between bench scale test and manikin test. Based on these studies, the overall performance of protective clothing against hot water spray can be estimated on the basis of the results of the bench scale hot water splashes test and the information of air gap size entrapped in clothing. The findings provide effective guides for the design and material selection while developing high performance protective clothing. Published by Oxford University Press on behalf of the British Occupational Hygiene Society 2014.

  8. Bench-Scale Evaluation of the Genifuel Hydrothermal Processing Technology for Wastewater Solids

    Energy Technology Data Exchange (ETDEWEB)

    Marrone, Philip A.; Elliott, Douglas C.; Billing, Justin M.; Hallen, Richard T.; Hart, Todd R.; Kadota, Paul; Moeller, Jeff C.; Randel, Margaaret A.; Schmidt, Andrew J.

    2017-10-03

    Hydrothermal Liquefaction (HTL) and Catalytic Hydrothermal Gasification (CHG) proof-of-concept bench-scale tests were performed to assess the potential of the Genifuel hydrothermal process technology for handling municipal wastewater sludge. HTL tests were conducted at 300-350°C and 20 MPa on three different feeds: primary sludge (11.9 wt% solids), secondary sludge (9.7 wt% solids), and post-digester sludge (also referred to as digested solids) (16.0 wt% solids). Corresponding CHG tests were conducted at 350°C and 20 MPa on the HTL aqueous phase output using a ruthenium based catalyst. A comprehensive analysis of all feed and effluent phases was also performed. Total mass and carbon balances closed to within ± 15% in all but one case. Biocrude yields from HTL tests were 37%, 25%, and 34% for primary sludge, secondary sludge, and digested solids feeds, respectively. The biocrude yields accounted for 59%, 39%, and 49% of the carbon in the feed for primary sludge, secondary sludge, and digested solids feeds, respectively. Biocrude composition and quality were comparable to that seen with biocrudes generated from algae feeds. Subsequent hydrotreating (i.e., upgrading) of the biocrude produced from primary sludge and digested solids resulted in a product with comparable physical and chemical properties to petroleum crude oil. CHG product gas consisted primarily of methane, with methane yields (relative to CHG input) on a carbon basis of 47%, 61%, and 64% for aqueous feeds that were the output of HTL tests with primary sludge, secondary sludge, and digested solids, respectively. Siloxane concentrations in the CHG product gas were below the detection limit and well below fuel input composition limits set by several engine manufacturers. Relative to that of the sludge feeds, the HTL-CHG process resulted in a reduction in chemical oxygen demand (COD) of greater than 99.9% and a reduction in residual solids for disposal of 94-99%. The test results, as a whole, support

  9. Bench Scale Thin Film Composite Hollow Fiber Membranes for Post-Combustion Carbon Dioxide Capture

    Energy Technology Data Exchange (ETDEWEB)

    Glaser, Paul [General Electric Global Research, Niskayuna, NY (United States); Bhandari, Dhaval [General Electric Global Research, Niskayuna, NY (United States); Narang, Kristi [General Electric Global Research, Niskayuna, NY (United States); McCloskey, Pat [General Electric Global Research, Niskayuna, NY (United States); Singh, Surinder [General Electric Global Research, Niskayuna, NY (United States); Ananthasayanam, Balajee [General Electric Global Research, Niskayuna, NY (United States); Howson, Paul [General Electric Global Research, Niskayuna, NY (United States); Lee, Julia [General Electric Global Research, Niskayuna, NY (United States); Wroczynski, Ron [General Electric Global Research, Niskayuna, NY (United States); Stewart, Frederick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Orme, Christopher [Idaho National Lab. (INL), Idaho Falls, ID (United States); Klaehn, John [Idaho National Lab. (INL), Idaho Falls, ID (United States); McNally, Joshua [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rownaghi, Ali [Georgia Inst. of Technology, Atlanta, GA (United States); Lu, Liu [Georgia Inst. of Technology, Atlanta, GA (United States); Koros, William [Georgia Inst. of Technology, Atlanta, GA (United States); Goizueta, Roberto [Georgia Inst. of Technology, Atlanta, GA (United States); Sethi, Vijay [Western Research Inst., Laramie, WY (United States)

    2015-04-01

    GE Global Research, Idaho National Laboratory (INL), Georgia Institute of Technology (Georgia Tech), and Western Research Institute (WRI) proposed to develop high performance thin film polymer composite hollow fiber membranes and advanced processes for economical post-combustion carbon dioxide (CO2) capture from pulverized coal flue gas at temperatures typical of existing flue gas cleanup processes. The project sought to develop and then optimize new gas separations membrane systems at the bench scale, including tuning the properties of a novel polyphosphazene polymer in a coating solution and fabricating highly engineered porous hollow fiber supports. The project also sought to define the processes needed to coat the fiber support to manufacture composite hollow fiber membranes with high performance, ultra-thin separation layers. Physical, chemical, and mechanical stability of the materials (individual and composite) towards coal flue gas components was considered via exposure and performance tests. Preliminary design, technoeconomic, and economic feasibility analyses were conducted to evaluate the overall performance and impact of the process on the cost of electricity (COE) for a coal-fired plant including capture technologies. At the onset of the project, Membranes based on coupling a novel selective material polyphosphazene with an engineered hollow fiber support was found to have the potential to capture greater than 90% of the CO2 in flue gas with less than 35% increase in COE, which would achieve the DOE-targeted performance criteria. While lab-scale results for the polyphosphazene materials were very promising, and the material was incorporated into hollow-fiber modules, difficulties were encountered relating to the performance of these membrane systems over time. Performance, as measured by both flux of and selectivity for CO2 over other flue gas constituents was found to deteriorate over time, suggesting a system that was

  10. Size distribution of chromate paint aerosol generated in a bench-scale spray booth.

    Science.gov (United States)

    Sabty-Daily, Rania A; Hinds, William C; Froines, John R

    2005-01-01

    Spray painters are potentially exposed to aerosols containing hexavalent chromium [Cr(VI)] via inhalation of chromate-based paint sprays. Evaluating the particle size distribution of a paint spray aerosol, and the variables that may affect this distribution, is necessary to determine the site and degree of respiratory deposition and the damage that may result from inhaled Cr(VI)-containing paint particles. This study examined the effect of spray gun atomization pressure, aerosol generation source and aerosol aging on the size distribution of chromate-based paint overspray aerosols generated in a bench-scale paint spray booth. The study also determined the effect of particle bounce inside a Marple personal cascade impactor on measured size distributions of paint spray aerosols. Marple personal cascade impactors with a modified inlet were used for sample collection. The data indicated that paint particle bounce did not occur inside the cascade impactors sufficiently to affect size distribution when using uncoated stainless steel or PVC substrate sampling media. A decrease in paint aerosol mass median aerodynamic diameter (MMAD) from 8.2 to 7.0 mum was observed as gun atomization pressure increased from 6 to 10 psi. Overspray aerosols were sampled at two locations in the spray booth. A downstream sampling position simulated the exposure of a worker standing between the painted surface and exhaust, a situation encountered in booths with multiple workers. The measured mean MMAD was 7.2 mum. The distance between the painted surface and sampler was varied to sample oversprays of varying ages between 2.8 and 7.7 s. Age was not a significant factor for determining MMAD. Overspray was sampled at a 90 degrees position to simulate a worker standing in front of the surface being painted with air flowing to the worker's side, a common situation in field applications. The resulting overspray MMAD averaged 5.9 mum. Direct-spray aerosols were sampled at ages from 5.3 to 11.7 s

  11. Soluble Microbial Product Characterization of Biofilm Formation in Bench-Scale

    KAUST Repository

    Mines, Paul

    2012-12-01

    The biological process known as activated sludge (AS) in conjunction with membrane separation technology for the treatment of wastewater has been employed for over four decades. While, membrane biological reactors (MBR) are now widely employed, the phenomenon of membrane fouling is still the most significant factor leading to performance decline of MBRs. Although much research has been done on the subject of MBR fouling over the past two decades, many questions remain unanswered, and consensus within the scientific community is rare. However, research has led to one system parameter generally being regarded as a contributor to membrane fouling, extracellular polymeric compounds (EPS). EPS, and more specifically, the soluble fraction of EPS known as soluble microbial products (SMP), must be further investigated in order to better understand membrane fouling. The biological activity and performance of the MBR is affected by myriad operational parameters, which in turn affects the SMP generated. A commonly varied operational parameter is, depending on the specific treatment needs of a MBR, the sludge retention time (SRT). This study aims to characterize the SMP in three bench-scale MBRs as the SRT is gradually lowered. By studying how the SMP change as the operation of the system is altered, greater understanding of how SMP are related to fouling can be achieved. At the onset of the study, a steady state was established in the system with a SRT of 20 days. Upon stabilization of a 20 day SRT, the system was gradually transitioned to a five and a half day SRT, in stepwise adjustments. Initially, both the trans-membrane pressure (TMP) and the SMP concentrations were at relatively low values, indicating the presence of minimal amounts of biofilm on the membrane surfaces. As the system was altered and more activated sludge was wasted from the reactors, the SRT inherently decreased. As the lower SRT was transitioned and established, the data from TMP measurements, as well

  12. Catalytic multi-stage liquefaction of coal at HTI: Bench-scale studies in coal/waste plastics coprocessing

    Energy Technology Data Exchange (ETDEWEB)

    Pradhan, V.R.; Lee, L.K.; Stalzer, R.H. [Hydrocarbon Technologies, Inc., Lawrenceville, NJ (United States)] [and others

    1995-12-31

    The development of Catalytic Multi-Stage Liquefaction (CMSL) at HTI has focused on both bituminous and sub-bituminous coals using laboratory, bench and PDU scale operations. The crude oil equivalent cost of liquid fuels from coal has been curtailed to about $30 per barrel, thus achieving over 30% reduction in the price that was evaluated for the liquefaction technologies demonstrated in the late seventies and early eighties. Contrary to the common belief, the new generation of catalytic multistage coal liquefaction process is environmentally very benign and can produce clean, premium distillates with a very low (<10ppm) heteroatoms content. The HTI Staff has been involved over the years in process development and has made significant improvements in the CMSL processing of coals. A 24 month program (extended to September 30, 1995) to study novel concepts, using a continuous bench scale Catalytic Multi-Stage unit (30kg coal/day), has been initiated since December, 1992. This program consists of ten bench-scale operations supported by Laboratory Studies, Modelling, Process Simulation and Economic Assessments. The Catalytic Multi-Stage Liquefaction is a continuation of the second generation yields using a low/high temperature approach. This paper covers work performed between October 1994- August 1995, especially results obtained from the microautoclave support activities and the bench-scale operations for runs CMSL-08 and CMSL-09, during which, coal and the plastic components for municipal solid wastes (MSW) such as high density polyethylene (HDPE)m, polypropylene (PP), polystyrene (PS), and polythylene terphthlate (PET) were coprocessed.

  13. EFRT M12 Issue Resolution: Comparison of PEP and Bench-Scale Oxidative Leaching Results

    Energy Technology Data Exchange (ETDEWEB)

    Rapko, Brian M.; Brown, Christopher F.; Eslinger, Paul W.; Fountain, Matthew S.; Hausmann, Tom S.; Huckaby, James L.; Hanson, Brady D.; Kurath, Dean E.; Minette, Michael J.

    2009-08-14

    20 wt% solids using cross-flow ultrafiltration before the addition of caustic. For wastes that have significantly high chromium content, the caustic leaching and slurry dewatering is followed by adding sodium permanganate to UFP-VSL-T02A, and the slurry is subjected to oxidative leaching at nominally ambient temperature. The purpose of the oxidative leaching is to selectively oxidize the poorly alkaline-soluble Cr(III) believed to be the insoluble form in Hanford tank sludge to the much more alkaline-soluble Cr(VI), e.g., chromate. The work described in this report provides the test results that are related to the efficiency of the oxidative leaching process to support process modeling based on tests performed with a Hanford waste simulant. The tests were completed both at the lab-bench scale and in the PEP. The purpose of this report is to summarize the results from both scales that are related to oxidative leaching chemistry to support a scale factor for the submodels to be used in the G2 model, which predicts WTP operating performance. Owing to schedule constraints, the PEP test data to be included in this report are limited to those from Integrated Tests A (T01 A/B caustic leaching) and B (T02A caustic leaching).

  14. Treatment of waste gas containing low concentration of dimethyl sulphide (DMS) in a bench-scale biofilter.

    Science.gov (United States)

    Giri, B S; Mudliar, S N; Deshmukh, S C; Banerjee, S; Pandey, R A

    2010-04-01

    Biological treatment of dimethyl sulphide (DMS) was investigated in a bench-scale biofilter, packed with compost along with wood chips, and enriched with DMS degrading microorganism Bacillus sphaericus. The biofilter could remove 62-74% of the inlet DMS, at an optimum loading of 0.484 g/m(3)/h with optimum empty bed contact time (EBCT) of 384 s and an average moisture range of 65-70%. The biodegradative products of DMS were sulphide, thiosulphate and sulphate. Evaluation of microbiological status of the biofilter indicated the presence of other bacterial cultures viz. Paenibacillus polymyxa, and Bacillus megaterium, besides B. sphaericus. Copyright 2009 Elsevier Ltd. All rights reserved.

  15. Bench-Scale Development of a Non-Aqueous Solvent (NAS) CO2 Capture Process for Coal-Fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Lail, Marty

    2017-09-12

    The project aimed to advance RTI’s non-aqueous amine solvent technology by improving the solvent to reduce volatility, demonstrating long-term continuous operation at lab- (0.5 liters solvent) and bench-scale (~120 liters solvent), showing low reboiler heat duty measured during bench-scale testing, evaluating degradation products, building a rate-based process model, and evaluating the techno-economic performance of the process. The project team (RTI, SINTEF, Linde Engineering) and the technology performed well in each area of advancement. The modifications incorporated throughout the project enabled the attainment of target absorber and regenerator conditions for the process. Reboiler duties below 2,000 kJt/kg CO2 were observed in a bench-scale test unit operated at RTI.

  16. Experimental and modelling studies on continuous synthesis and refining of biodiesel in a dedicated bench scale unit using centrifugal contactor separator technology

    NARCIS (Netherlands)

    Abduh, Muhammad Yusuf; Martinez, Alberto Fernandez; Kloekhorst, Arjan; Manurung, Robert; Heeres, Hero J.

    Continuous synthesis and refining of biodiesel (FAME) using a laboratory scale bench scale unit was explored. The unit consists of three major parts: (i) a continuous centrifugal contactor separator (CCCS) to perform the reaction between sunflower oil and methanol; (ii) a washing unit for the crude

  17. Crucible melts and bench-scale ISV [in situ vitrification] tests on simulated wastes in INEL [Idaho National Engineering Laboratory] soils

    International Nuclear Information System (INIS)

    Farnsworth, R.K.; Oma, K.H.; Reimus, M.A.H.

    1990-05-01

    This report summarizes the results of eight crucible melt tests and three bench-scale in situ vitrification (ISV) test that were performed on simulated metals/soils mixtures containing actual site soils from the Idaho National Engineering Laboratory (INEL). The crucible melt and bench-scale ISV tests are a part of efforts by the Pacific Northwest Laboratory (PNL) to assist the INEL in conducting a treatability study on ISV for application to the mixed waste buried at the INEL subsurface disposal area (SDA). The crucible melt tests were performed to evaluate the effect of various chemical additives and metal oxidation techniques on soil melting temperatures, melt viscosities, metals versus electrode oxidation potentials, and metals incorporation in the glass. The bench-scale ISV tests were performed to supplement the existing ISV data base with information on certain hazardous materials that have not been adequately evaluated in previous ISV tests. These materials included five EP toxicity metals, various volatile organic materials fixed in a cementitious matrix [including carbon tetrachloride (CCl 4 ), trichloroethylene (TCE), and tetrachloroethylene (PCE)], and asbestos. In addition, the bench-scale test were used to evaluated the effect of the proposed chemical additive on ISV processing performance and product quality. 8 refs., 24 figs., 19 tabs

  18. Bench Scale Development and Testing of Aerogel Sorbents for CO2 Capture Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Begag, Redouane [Aspen Aerogels, Northborough, MA (United States)

    2017-03-30

    The primary objective of this project was scaling up and evaluating a novel Amine Functionalized Aerogel (AFA) sorbent in a bench scale fluidized bed reactor. The project team (Aspen Aerogels, University of Akron, ADA-ES, and Longtail Consulting) has carried out numerous tests and optimization studies to demonstrate the CO2 capture performance of the AFA sorbent in all its forms: powder, pellet, and bead. The CO2 capture target performance of the AFA sorbent (all forms) were set at > 12 wt.% and > 6 wt.% for total and working CO2 capacity, respectively (@ 40 °C adsorption / 100 – 120 °C desorption). The optimized AFA powders outperformed the performance targets by more than 30%, for the total CO2 capacity (14 - 20 wt.%), and an average of 10 % more for working CO2 capacity (6.6 – 7.0 wt.%, and could be as high as 9.6 wt. % when desorbed at 120 °C). The University of Akron developed binder formulations, pellet production methods, and post treatment technology for increased resistance to attrition and flue gas contaminants. In pellet form the AFA total CO2 capacity was ~ 12 wt.% (over 85% capacity retention of that of the powder), and there was less than 13% degradation in CO2 capture capacity after 20 cycles in the presence of 40 ppm SO2. ADA-ES assessed the performance of the AFA powder, pellet, and bead by analyzing sorption isotherms, water uptake analysis, cycling stability, jet cup attrition and crush tests. At bench scale, the hydrodynamic and heat transfer properties of the AFA sorbent pellet in fluidized bed conditions were evaluated at Particulate Solid Research, Inc. (PSRI). After the process design requirements were completed, by Longtail Consulting LLC, a techno-economic analysis was achieved using guidance from The National Energy Technology Laboratory (NETL) report. This report provides the necessary framework to estimate costs for a temperature swing post

  19. Bench Scale Treatability Studies of Contaminated Soil Using Soil Washing Technique

    Directory of Open Access Journals (Sweden)

    M. K. Gupta

    2010-01-01

    Full Text Available Soil contamination is one of the most widespread and serious environmental problems confronting both the industrialized as well as developing nations like India. Different contaminants have different physicochemical properties, which influence the geochemical reactions induced in the soils and may bring about changes in their engineering and environmental behaviour. Several technologies exist for the remediation of contaminated soil and water. In the present study soil washing technique using plain water with surfactants as an enhancer was used to study the remediation of soil contaminated with (i an organic contaminant (engine lubricant oil and (ii an inorganic contaminant (heavy metal. The lubricant engine oil was used at different percentages (by dry weight of the soil to artificially contaminate the soil. It was found that geotechnical properties of the soil underwent large modifications on account of mixing with the lubricant oil. The sorption experiments were conducted with cadmium metal in aqueous medium at different initial concentration of the metal and at varying pH values of the sorbing medium. For the remediation of contaminated soil matrices, a nonionic surfactant was used for the restoration of geotechnical properties of lubricant oil contaminated soil samples, whereas an anionic surfactant was employed to desorb cadmium from the contaminated soil matrix. The surfactant in case of soil contaminated with the lubricant oil was able to restore properties to an extent of 98% vis-à-vis the virgin soil, while up to 54% cadmium was desorbed from the contaminated soil matrix in surfactant aided desorption experiments.

  20. In Developping a Bench-Scale Circulating Fluidized Bed Combustor to Burn High Ash Brazilian Coal-Dolomites Mixtures

    Science.gov (United States)

    Ramírez Behainne, Jhon Jairo; Hory, Rogério Ishikawa; Goldstein, Leonardo; Bernárdez Pécora, Araí Augusta

    This work considers some of the questions in burning high ash Brazilian coal-dolomite mixtures in a bench-scale circulating fluidized bed combustor (CFBC). Experimental tests were performed with the CE4500 coal from Santa Catarina State, in southern Brazil, with a Sauter mean diameter d p =43 μm. The coal particles were mixed with dolomite particles of d p = 111 μm and this fuel mixture was fed into the circulating fluidized reactor, previously loaded with quartz sand particles of d p =353 μm. This inert material was previously heated by the combustion of liquefied petroleum gas up to the ignition temperature of the fuel mixture. The CFBC unit has a 100mm internal diameter riser, 4.0m high, as well as a 62.8mm internal diameter downcomer. The loop has a cyclone, a sampling valve to collect particles and a 62.8mm internal diameter L-valve to recirculate the particles in the loop. A screw feeder with a rotation control system was used to feed the fuel mixture to the reactor. The operational conditions were monitored by pressure taps and thermocouples installed along the loop. A data acquisition system showed the main operational conditions to control. Experimental tests performed put in evidence the problems found during bed operation, with special attention to the solids feed device, to the L-valve operation, to particle size, solids inventory, fluidized gas velocity, fuel mixture and recirculated solids feeding positions.

  1. In-situ biogas upgrading during anaerobic digestion of food waste amended with walnut shell biochar at bench scale.

    Science.gov (United States)

    Linville, Jessica L; Shen, Yanwen; Ignacio-de Leon, Patricia A; Schoene, Robin P; Urgun-Demirtas, Meltem

    2017-06-01

    A modified version of an in-situ CO 2 removal process was applied during anaerobic digestion of food waste with two types of walnut shell biochar at bench scale under batch operating mode. Compared with the coarse walnut shell biochar, the fine walnut shell biochar has a higher ash content (43 vs. 36 wt%) and higher concentrations of calcium (31 vs. 19 wt% of ash), magnesium (8.4 vs. 5.6 wt% of ash) and sodium (23.4 vs. 0.3 wt% of ash), but a lower potassium concentration (0.2 vs. 40% wt% of ash). The 0.96-3.83 g biochar (g VS added ) -1 fine walnut shell biochar amended digesters produced biogas with 77.5%-98.1% CH 4 content by removing 40%-96% of the CO 2 compared with the control digesters at mesophilic and thermophilic temperature conditions. In a direct comparison at 1.83 g biochar (g VS added ) -1 , the fine walnut shell biochar amended digesters (85.7% CH 4 content and 61% CO 2 removal) outperformed the coarse walnut shell biochar amended digesters (78.9% CH 4 content and 51% CO 2 removal). Biochar addition also increased alkalinity as CaCO 3 from 2800 mg L -1 in the control digesters to 4800-6800 mg L -1 , providing process stability for food waste anaerobic digestion.

  2. Bench scale synthesis of p-hydroxybenzoic acid using whole-cell nitrilase of Gordonia terrae mutant E9.

    Science.gov (United States)

    Kumar, Vijay; Kumar, Virender; Thakur, Neerja; Bhalla, Tek Chand

    2015-07-01

    Mutants of Gordonia terrae were generated using chemical mutagens for better activity, stability and higher substrate/product tolerance of its nitrilase enzyme. Mutant E9 showed two-time increase in activity and tolerated p-hydroxybenzonitrile (p-HBN) up to 50 mM. Response surface methodology and inducer mediation approach further enhanced the production of enzyme to 2.5-fold. The bench scale production of p-hydroxybenzoic acid (p-HBA) was carried out in a fed-batch reaction (500-mL scale) using whole-cell nitrilase of mutant E9 in 0.1 M potassium phosphate buffer (pH 8.0) at 40 °C. Total six feedings each at an interval of 45 min resulted in accumulation of 360 mM (21.6 g) of p-HBA with a purity of 99%. The catalytic and volumetric productivity of bioprocess using mutant G. terrae was improved to 1.8 g h(-1) g DCW (-1) and 43.2 g L(-1), respectively, from 0.78 g h(-1) g DCW (-1) and 28.8 g L(-1) using resting cells of wild strain. K m and V max of purified nitrilase from mutant E9 were 55 U mg(-1) and 1.8 mM for p-HBN with a higher turnover number of 36 s(-1) × 10(-3).

  3. Modeling a bench-scale alternating aerobic/anoxic activated sludge system for nitrogen removal using a modified ASM1.

    Science.gov (United States)

    Kim, Hyunook; Noh, Soohong; Colosimo, Mark

    2009-07-01

    The Activated Sludge Model No. 1 (ASM1), developed by The International Association of Water Pollution Research and Control, was applied to model dynamics of NH4+, and NO3- in a bench scale alternating aerobic-anoxic (AAA) activated sludge system for nitrogen removal. The model was modified by eliminating inert soluble COD (S(I)) and inert particulate COD (X(I)) from the model's state variables as these two variables are not involved in any biological reaction and are not readily measurable with conventional routine COD analysis. It was assumed that the soluble COD and particulate COD of wastewater represent readily biodegradable COD (S(S)) and slowly biodegradable (X(S)) in the model, respectively. In addition, alkalinity was also removed from the model, since alkalinity of an AAA system remains stable due to the cyclic modes of the system. Even with the elimination of the three state variables and the assumption made, the model could reasonably predict the NH4+ and NO3- dynamics of the AAA system, and effluent NH4+ and NO3- concentrations with adjustment of only a few kinetic parameters. Compared to the original ASM1, it is expected that the modified ASM1 presented in this study can be more easily utilized by engineers in designing or operating an AAA system in practice, since it requires simple characterization of wastewater COD.

  4. 15N NMR investigation of the reduction and binding of TNT in an aerobic bench scale reactor simulating windrow composting

    Science.gov (United States)

    Thorn, K.A.; Pennington, J.C.; Hayes, C.A.

    2002-01-01

    T15NT was added to a soil of low organic carbon content and composted for 20 days in an aerobic bench scale reactor. The finished whole compost and fulvic acid, humic acid, humin, and lignocellulose fractions extracted from the compost were analyzed by solid-state CP/MAS and DP/MAS 15N NMR. 15N NMR spectra provided direct spectroscopic evidence for reduction of TNT followed by covalent binding of the reduced metabolites to organic matter of the composted soil, with the majority of metabolite found in the lignocellulose fraction, by mass also the major fraction of the compost. In general, the types of bonds formed between soil organic matter and reduced TNT amines in controlled laboratory reactions were observed in the spectra of the whole compost and fractions, confirming that during composting TNT is reduced to amines that form covalent bonds with organic matter through aminohydroquinone, aminoquinone, heterocyclic, and imine linkages, among others. Concentrations of imine nitrogens in the compost spectra suggestthat covalent binding bythe diamines 2,4DANT and 2,6DANT is a significant process in the transformation of TNT into bound residues. Liquid-phase 15N NMR spectra of the fulvic acid and humin fractions provided possible evidence for involvement of phenoloxidase enzymes in covalent bond formation.

  5. Inactivation of Escherichia coli by ozone under bench-scale plug flow and full-scale hydraulic conditions.

    Science.gov (United States)

    Smeets, P W M H; van der Helm, A W C; Dullemont, Y J; Rietveld, L C; van Dijk, J C; Medema, G J

    2006-10-01

    To determine the disinfection efficacy of ozonation, water companies can apply several disinfection calculation methods. The goal of this study was to evaluate the use of the T10 and continuous stirred tank reactor (CSTR) method to extrapolate inactivation rates of ozone sensitive microorganisms observed in laboratory tests to full-scale ozonation in drinking water treatment. The inactivation efficacy of the ozonation at the Amsterdam water treatment works was assessed by determining Escherichia coli concentrations in large volume samples before and after ozonation over a period of 1 year. The inactivation of dosed E. coli WR1 was tested in a bench-scale dissolved ozone plug flow reactor (DOPFR) on the same feed water as the full-scale ozonation in which a concentrated ozone solution in Milli-Q water was dosed. Applying the T10 method on the inactivation rates observed in the DOPFR strongly overestimated the inactivation capacity of the full-scale ozonation. The expected inactivation based on the CSTR method (LT2ESWTR) approached the observed inactivation at full-scale. Therefore, the CSTR method should be preferred to calculate inactivation of ozone sensitive organisms such as E. coli, viruses, Giardia and Campylobacter by full-scale ozonation.

  6. Bench-scale study of the effect of phosphate on an aerobic iron oxidation plant for mine water treatment.

    Science.gov (United States)

    Tischler, Judith S; Wiacek, Claudia; Janneck, Eberhard; Schlömann, Michael

    2014-01-01

    At the opencast pit Nochten acidic iron- and sulfate-rich mine waters are treated biotechnologically in a mine-water treatment plant by microbial iron oxidation. Due to the low phosphate concentration in such waters the treatment plant was simulated in bench-scale to investigate the influence of addition of potassium dihydrogen phosphate on chemical and biological parameters of the mine-water treatment. As a result of the phosphate addition the number of cells increased, which resulted in an increase of the iron oxidation rate in the reactor with phosphate addition by a factor of 1.7 compared to a reference approach without phosphate addition. Terminal restriction fragment length polymorphism (T-RFLP) analysis during the cultivation revealed a shift of the microbial community depending on the phosphate addition. While almost exclusively iron-oxidizing bacteria related to "Ferrovum" sp. were detected with phosphate addition, the microbial community was more diverse without phosphate addition. In the latter case, iron-oxidizing bacteria ("Ferrovum" sp., Acidithiobacillus spp.) as well as non-iron-oxidizing bacteria (Acidiphilium sp.) were identified. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Thermochemical water-splitting cycle, bench-scale investigations, and process engineering. Final report, February 1977-December 31, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Norman, J.H.; Besenbruch, G.E.; Brown, L.C.; O' Keefe, D.R.; Allen, C.L.

    1982-05-01

    The sulfur-iodine water-splitting cycle is characterized by the following three reactions: 2H/sub 2/O + SO/sub 2/ + I/sub 2/ ..-->.. H/sub 2/SO/sub 4/ + 2HI; H/sub 2/SO/sub 4/ ..-->.. H/sub 2/O + SO/sub 2/ + 1/2 O/sub 2/; and 2HI ..-->.. H/sub 2/ + I/sub 2/. This cycle was developed at General Atomic after several critical features in the above reactions were discovered. These involved phase separations, catalytic reactions, etc. Estimates of the energy efficiency of this economically reasonable advanced state-of-the-art processing unit produced sufficiently high values (to approx.47%) to warrant cycle development effort. The DOE contract was largely directed toward the engineering development of this cycle, including a small demonstration unit (CLCD), a bench-scale unit, engineering design, and costing. The work has resulted in a design that is projected to produce H/sub 2/ at prices not yet generally competitive with fossil-fuel-produced H/sub 2/ but are projected to be favorably competitive with respect to H/sub 2/ from fossil fuels in the future.

  8. Dynamics of bacterial populations during bench-scale bioremediation of oily seawater and desert soil bioaugmented with coastal microbial mats.

    Science.gov (United States)

    Ali, Nidaa; Dashti, Narjes; Salamah, Samar; Sorkhoh, Naser; Al-Awadhi, Husain; Radwan, Samir

    2016-03-01

    This study describes a bench-scale attempt to bioremediate Kuwaiti, oily water and soil samples through bioaugmentation with coastal microbial mats rich in hydrocarbonoclastic bacterioflora. Seawater and desert soil samples were artificially polluted with 1% weathered oil, and bioaugmented with microbial mat suspensions. Oil removal and microbial community dynamics were monitored. In batch cultures, oil removal was more effective in soil than in seawater. Hydrocarbonoclastic bacteria associated with mat samples colonized soil more readily than seawater. The predominant oil degrading bacterium in seawater batches was the autochthonous seawater species Marinobacter hydrocarbonoclasticus. The main oil degraders in the inoculated soil samples, on the other hand, were a mixture of the autochthonous mat and desert soil bacteria; Xanthobacter tagetidis, Pseudomonas geniculata, Olivibacter ginsengisoli and others. More bacterial diversity prevailed in seawater during continuous than batch bioremediation. Out of seven hydrocarbonoclastic bacterial species isolated from those cultures, only one, Mycobacterium chlorophenolicum, was of mat origin. This result too confirms that most of the autochthonous mat bacteria failed to colonize seawater. Also culture-independent analysis of seawater from continuous cultures revealed high-bacterial diversity. Many of the bacteria belonged to the Alphaproteobacteria, Flavobacteria and Gammaproteobacteria, and were hydrocarbonoclastic. Optimal biostimulation practices for continuous culture bioremediation of seawater via mat bioaugmentation were adding the highest possible oil concentration as one lot in the beginning of bioremediation, addition of vitamins, and slowing down the seawater flow rate. © 2016 The Author. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

  9. Bench-Scale and Pilot-Scale Treatment Technologies for the ...

    Science.gov (United States)

    Coal mine water (CMW) is typically treated to remove suspended solids, acidity, and soluble metals, but high concentrations of total dissolved solids (TDS) have been reported to impact the environment at several CMW discharge points. Consequently, various states have established TDS wastewater regulations and the US EPA has proposed a benchmark conductivity limit to reduce TDS impacts in streams near mining sites. Traditional CMW treatment effectively removes some TDS components, but is not effective in removing major salt ions due to their higher solubility. This paper describes the basic principles, effectiveness, advantages and disadvantages of various TDS removal technologies (adsorption, bioremediation, capacitive deionization, desalination, electro-chemical ion exchange, electrocoagulation, electrodialysis, ion exchange, membrane filtration, precipitation, and reverse osmosis) that have at least been tested in bench- and pilot-scale experiments. Recent discussions about new regulations to include total dissolved solids TDS) limits would propel interest in the TDS removal technologies focused on coal mine water. TDS removal is not a new concept and has been developed using different technologies for a number of applications, but coal mine water has unique characteristics (depending on the site, mining process, and solid-water-oxygen interactions), which make it unlikely to have a single technology predominating over others. What are some novel technolog

  10. Effect of temperature downshifts on a bench-scale hybrid A/O system: Process performance and microbial community dynamics.

    Science.gov (United States)

    Zhou, Hexi; Li, Xiangkun; Chu, Zhaorui; Zhang, Jie

    2016-06-01

    Effect of temperature downshifts on process performance and bacterial community dynamics was investigated in a bench-scale hybrid A/O system treating real domestic wastewater. Results showed that the average COD removal in this system reached 90.5%, 89.1% and 90.3% for Run 1 (25 °C), Run 2 (15 °C) and Run 3 (10 °C), respectively, and variations in temperature barely affected the effluent COD concentration. The average removal efficiencies of NH4(+)-N were 98.4%, 97.8%, 95.7%, and that of TN were 77.1%, 61.8%, 72% at 25 °C, 15 °C and 10 °C, respectively. Although the hybrid system was subjected to low temperature, this process effectively removed NH4(+)-N and TN even at 10 °C with the average effluent concentrations of 2.4 mg/L and 14.3 mg/L, respectively. Results from high-throughput sequencing analysis revealed that when the operation temperature decreased from 25 °C to 10 °C, the richness and diversity indexes of the system decreased in the sludge samples, while underwent an increase in the biofilm samples. Furthermore, the major heterotrophic bacteria consisted of Lewinella, Lutimonas, Chitinophaga and Fluviicola at 10 °C, which could be central to effective COD removal at low temperature. Additionally, Azospira, one denitrifying-related genus increased from 0.4% to 4.45% in the biofilm samples, with a stable TN removal in response to temperature downshifts. Nitrosomonas and Nitrospira increased significantly in the biofilm samples, implying that the attached biofilm contributed to more nitrification at low temperature. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Destruction of hazardous and mixed wastes using mediated electrochemical oxidation in a Ag(II)HNO3 bench scale system

    International Nuclear Information System (INIS)

    Balazs, B.; Chiba, Z.; Hsu, P.; Lewis, P.; Murguia, L.; Adamson, M.

    1997-01-01

    Mediated Electrochemical Oxidation (MEO) is a promising technology for the destruction of organic containing wastes and the remediation of mixed wastes containing transuranic components. The combination of a powerful oxidant and an acid solution allows the conversion of nearly all organics, whether present in hazardous or in mixed waste, to carbon dioxide. Insoluble transuranics are dissolved in this process and may be recovered by separation and precipitation.The MEO technique offers several advantages which are inherent in the system. First, the oxidation/dissolution processes are accomplished at near ambient pressures and temperatures (30-70 degrees C). Second, all waste stream components and oxidation products (with the exception of evolved gases) are contained in an aqueous environment. This electrolyte acts as an accumulator for inorganics which were present in the original waste stream, and the large volume of electrolyte provides a thermal buffer for the energy released during oxidation of the organics. Third, the generation of secondary waste is minimal, as the process needs no additional reagents. Finally, the entire process can be shut down by simply turning off the power, affording a level of control unavailable in some other techniques.Numerous groups, both in the United States and Europe, have made substantial progress in the last decade towards understanding the mechanistic pathways, kinetics, and engineering aspects of the process. At Lawrence Livermore National Laboratory, substantial contributions have been made to this knowledge base in these areas and others. Conceptual design and engineering development have been completed for a pilot plant-scale MEO system, and numerous data have been gathered on the efficacy of the process for a wide variety of anticipated waste components. This presentation will review the data collected at LLNL for a bench scale system based primarily on the use of a Ag(II) mediator in a nitric acid electrolyte; results

  12. Archaeal and bacterial community dynamics and bioprocess performance of a bench-scale two-stage anaerobic digester.

    Science.gov (United States)

    Gonzalez-Martinez, Alejandro; Garcia-Ruiz, Maria Jesus; Rodriguez-Sanchez, Alejandro; Osorio, Francisco; Gonzalez-Lopez, Jesus

    2016-07-01

    Two-stage technologies have been developed for anaerobic digestion of waste-activated sludge. In this study, the archaeal and bacterial community structure dynamics and bioprocess performance of a bench-scale two-stage anaerobic digester treating urban sewage sludge have been studied by the means of high-throughput sequencing techniques and physicochemical parameters such as pH, dried sludge, volatile dried sludge, acid concentration, alkalinity, and biogas generation. The coupled analyses of archaeal and bacterial communities and physicochemical parameters showed a direct relationship between archaeal and bacterial populations and bioprocess performance during start-up and working operation of a two-stage anaerobic digester. Moreover, results demonstrated that archaeal and bacterial community structure was affected by changes in the acid/alkalinity ratio in the bioprocess. Thus, a predominance of the acetoclastic methanogen Methanosaeta was observed in the methanogenic bioreactor at high-value acid/alkaline ratio, while a predominance of Methanomassilicoccaeceae archaea and Methanoculleus genus was observed in the methanogenic bioreactor at low-value acid/alkaline ratio. Biodiversity tag-iTag sequencing studies showed that methanogenic archaea can be also detected in the acidogenic bioreactor, although its biological activity was decreased after 4 months of operation as supported by physicochemical analyses. Also, studies of the VFA producers and VFA consumers microbial populations showed as these microbiota were directly affected by the physicochemical parameters generated in the bioreactors. We suggest that the results obtained in our study could be useful for future implementations of two-stage anaerobic digestion processes at both bench- and full-scale.

  13. Experimental investigation of pyrolysis of rice straw using bench-scale auger, batch and fluidized bed reactors

    International Nuclear Information System (INIS)

    Nam, Hyungseok; Capareda, Sergio C.; Ashwath, Nanjappa; Kongkasawan, Jinjuta

    2015-01-01

    Energy conversion efficiencies of three pyrolysis reactors (bench-scale auger, batch, and fluidized bed) were investigated using rice straw as the feedstock at a temperature of 500 °C. The highest bio-oil yield of 43% was obtained from the fluidized bed reactor, while the maximum bio-char yield of 48% was obtained from the batch reactor. Similar bio-oil yields were obtained from the auger and batch type reactors. The GCMS and FTIR were used to evaluate the liquid products from all reactors. The best quality bio-oil and bio-char from the batch reactor was determined to have a heating value of 31 MJ/kg and 19 MJ/kg, respectively. The highest alkali mineral was found in the bio-char produced from the auger reactor. The energy conversion efficiencies of the three reactors indicated that the majority of the energy (50–64%) was in the bio-char products from the auger and batch reactors, while the bio-oil from the fluidized bed reactor contained the highest energy (47%). A Sankey diagram has been produced to show the flows of product energy from each pyrolysis process. The result will help determine which conversion process would be optimal for producing specific products of bio-char, bio-oil, and gas depending on the needs. - Highlights: • Pyrolysis products from auger, batch, and fluidized bed reactor were examined. • O/C ratios of bio-oils stayed in specific ranges depending on the process reactors. • The largest quantity of bio-oil from fluidized, while the best quality from batch. • The highest alkali concentration of 37 g/kg included in the auger based bio-char. • Sankey diagram was used to understand the energy distribution from reactors.

  14. In-situ subaqueous capping of mercury-contaminated sediments in a fresh-water aquatic system, Part I—Bench-scale microcosm study to assess methylmercury production

    Energy Technology Data Exchange (ETDEWEB)

    Randall, Paul M., E-mail: randall.paul@epa.gov [U.S. Environmental Protection Agency, Office of Research and Development, National Risk Management Research Laboratory, 26 W. Martin Luther King Drive, Cincinnati, OH 45268 (United States); Fimmen, Ryan [Geosyntec Consultants, 150 E. Wilson Bridge Road, Suite 232, Worthington, OH 43085 (United States); Lal, Vivek; Darlington, Ramona [Battelle, 505 King Ave., Columbus, OH 43201 (United States)

    2013-08-15

    Bench-scale microcosm experiments were designed to provide a better understanding of the potential for Hg methylation in sediments from an aquatic environment. Experiments were conducted to examine the function of sulfate concentration, lactate concentration, the presence/absence of an aqueous inorganic Hg spike, and the presence/absence of inoculums of Desulfovibrio desulfuricans, a strain of sulfate-reducing bacteria (SRB) commonly found in the natural sediments of aquatic environments. Incubations were analyzed for both the rate and extent of (methylmercury) MeHg production. Methylation rates were estimated by analyzing MeHg and Hg after 2, 7, 14, 28, and 42 days. The production of metabolic byproducts, including dissolved gases as a proxy for metabolic utilization of carbon substrate, was also monitored. In all treatments amended with lactate, sulfate, Hg, and SRB, MeHg was produced (37 ng/g-sediment dry weight) after only 48 h of incubation and reached a maximum sediment concentration of 127 ng/g-sediment dry weight after the 42 day incubation period. Aqueous phase production of MeHg was observed to be 10 ng/L after 2 day, reaching a maximum observed concentration of 32.8 ng/L after 14 days, and declining to 10.8 ng/L at the end of the incubation period (42 day). The results of this study further demonstrates that, in the presence of an organic carbon substrate, sulfate, and the appropriate consortia of microorganisms, sedimentary Hg will be transformed into MeHg through bacterial metabolism. Further, this study provided the basis for evaluation of an in-situ subaqueous capping strategy that may limit (or potentially enhance) MeHg production. -- Highlights: • Hg methylation by SRB is limited by the depletion of sulfate and carbon. • Hg methylation is sensitive to competition by methanogens for carbon substrate. • In high lactate environment, all lactate was utilized in the microcosms within seven days. • In the absence of adequate metabolic fuel, Me

  15. In-situ subaqueous capping of mercury-contaminated sediments in a fresh-water aquatic system, Part I—Bench-scale microcosm study to assess methylmercury production

    International Nuclear Information System (INIS)

    Randall, Paul M.; Fimmen, Ryan; Lal, Vivek; Darlington, Ramona

    2013-01-01

    Bench-scale microcosm experiments were designed to provide a better understanding of the potential for Hg methylation in sediments from an aquatic environment. Experiments were conducted to examine the function of sulfate concentration, lactate concentration, the presence/absence of an aqueous inorganic Hg spike, and the presence/absence of inoculums of Desulfovibrio desulfuricans, a strain of sulfate-reducing bacteria (SRB) commonly found in the natural sediments of aquatic environments. Incubations were analyzed for both the rate and extent of (methylmercury) MeHg production. Methylation rates were estimated by analyzing MeHg and Hg after 2, 7, 14, 28, and 42 days. The production of metabolic byproducts, including dissolved gases as a proxy for metabolic utilization of carbon substrate, was also monitored. In all treatments amended with lactate, sulfate, Hg, and SRB, MeHg was produced (37 ng/g-sediment dry weight) after only 48 h of incubation and reached a maximum sediment concentration of 127 ng/g-sediment dry weight after the 42 day incubation period. Aqueous phase production of MeHg was observed to be 10 ng/L after 2 day, reaching a maximum observed concentration of 32.8 ng/L after 14 days, and declining to 10.8 ng/L at the end of the incubation period (42 day). The results of this study further demonstrates that, in the presence of an organic carbon substrate, sulfate, and the appropriate consortia of microorganisms, sedimentary Hg will be transformed into MeHg through bacterial metabolism. Further, this study provided the basis for evaluation of an in-situ subaqueous capping strategy that may limit (or potentially enhance) MeHg production. -- Highlights: • Hg methylation by SRB is limited by the depletion of sulfate and carbon. • Hg methylation is sensitive to competition by methanogens for carbon substrate. • In high lactate environment, all lactate was utilized in the microcosms within seven days. • In the absence of adequate metabolic fuel, Me

  16. Bench scale experiments for the remediation of Hanford Waste Treatment Plant low activity waste melter off-gas condensate

    Energy Technology Data Exchange (ETDEWEB)

    Taylor-Pashow, Kathryn M.L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Poirier, Michael [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McCabe, Daniel J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-08-11

    The Low Activity Waste (LAW) vitrification facility at the Hanford Waste Treatment and Immobilization Plant (WTP) will generate an aqueous condensate recycle stream (LAW Off-Gas Condensate) from the off-gas system. The plan for disposition of this stream during baseline operations is to send it to the WTP Pretreatment Facility, where it will be blended with LAW, concentrated by evaporation and recycled to the LAW vitrification facility again. The primary reason to recycle this stream is so that the semi-volatile 99Tc isotope eventually becomes incorporated into the glass. This stream also contains non-radioactive salt components that are problematic in the melter, so diversion of this stream to another process would eliminate recycling of these salts and would enable simplified operation of the LAW melter and the Pretreatment Facilities. This diversion from recycling this stream within WTP would have the effect of decreasing the LAW vitrification mission duration and quantity of glass waste. The concept being tested here involves removing the 99Tc so that the decontaminated aqueous stream, with the problematic salts, can be disposed elsewhere.

  17. Permeable Reactive Biobarriers for In Situ Cr(VI) Reduction: Bench Scale Tests Using Cellulomonas sp. Strain ES6

    Energy Technology Data Exchange (ETDEWEB)

    Sridhar Viamajala; Brent M. Peyton; Robin Gerlach; Vaideeswaran; William A. Apel; James N. Petersen

    2008-12-01

    Chromate (Cr(VI)) reduction studies were performed in bench scale flow columns using the fermentative subsurface isolate Cellulomonas sp. strain ES6. In these tests, columns packed with either quartz sand or hydrous ferric oxide (HFO)-coated quartz sand, were inoculated with strain ES6 and fed nutrients to stimulate growth before nutrient-free Cr(VI) solutions were injected. Results show that in columns containing quartz sand, a continuous inflow of 2 mg/L Cr(VI) was reduced to below detection limits in the effluent for durations of up to 5.7 residence times after nutrient injection was discontinued proving the ability of strain ES6 to reduce chromate in the absence of an external electron donor. In the HFO-containing columns, Cr(VI) reduction was significantly prolonged and effluent Cr(VI) concentrations remained below detectable levels for periods of up to 66 residence times after nutrient injection was discontinued. Fe was detected in the effluent of the HFO-containing columns throughout the period of Cr(VI) removal indicating that the insoluble Fe(III) bearing solids were being continuously reduced to form soluble Fe(II) resulting in prolonged abiotic Cr(VI) reduction. Thus, growth of Cellulomonas within the soil columns resulted in formation of permeable reactive barriers that could reduce Cr(VI) and Fe(III) for extended periods even in the absence of external electron donors. Other bioremediation systems employing Fe(II)-mediated reactions require a continuous presence of external nutrients to regenerate Fe(II). After depletion of nutrients, contaminant removal within these systems occurs by reaction with surface-associated Fe(II) that can rapidly become inaccessible due to formation of crystalline Fe-minerals or other precipitates. The ability of fermentative organisms like Cellulomonas to reduce metals without continuous nutrient supply in the subsurface offers a viable and economical alternative technology for in situ remediation of Cr

  18. Permeable reactive biobarriers for in situ Cr(VI) reduction: bench scale tests using Cellulomonas sp. strain ES6.

    Science.gov (United States)

    Viamajala, Sridhar; Peyton, Brent M; Gerlach, Robin; Sivaswamy, Vaideeswaran; Apel, William A; Petersen, James N

    2008-12-15

    Chromate (Cr(VI)) reduction studies were performed in bench scale flow columns using the fermentative subsurface isolate Cellulomonas sp. strain ES6. In these tests, columns packed with either quartz sand or hydrous ferric oxide (HFO)-coated quartz sand, were inoculated with strain ES6 and fed nutrients to stimulate growth before nutrient-free Cr(VI) solutions were injected. Results show that in columns containing quartz sand, a continuous inflow of 2 mg/L Cr(VI) was reduced to below detection limits in the effluent for durations of up to 5.7 residence times after nutrient injection was discontinued proving the ability of strain ES6 to reduce chromate in the absence of an external electron donor. In the HFO-containing columns, Cr(VI) reduction was significantly prolonged and effluent Cr(VI) concentrations remained below detectable levels for periods of up to 66 residence times after nutrient injection was discontinued. Fe was detected in the effluent of the HFO-containing columns throughout the period of Cr(VI) removal indicating that the insoluble Fe(III) bearing solids were being continuously reduced to form soluble Fe(II) resulting in prolonged abiotic Cr(VI) reduction. Thus, growth of Cellulomonas within the soil columns resulted in formation of permeable reactive barriers that could reduce Cr(VI) and Fe(III) for extended periods even in the absence of external electron donors. Other bioremediation systems employing Fe(II)-mediated reactions require a continuous presence of external nutrients to regenerate Fe(II). After depletion of nutrients, contaminant removal within these systems occurs by reaction with surface-associated Fe(II) that can rapidly become inaccessible due to formation of crystalline Fe-minerals or other precipitates. The ability of fermentative organisms like Cellulomonas to reduce metals without continuous nutrient supply in the subsurface offers a viable and economical alternative technology for in situ remediation of Cr

  19. Flue gas conditioning for improved particle collection in electrostatic precipitators. Second topical report, Results of bench-scale screening of additives

    Energy Technology Data Exchange (ETDEWEB)

    Durham, M.D.

    1993-08-13

    ADA Technologies, Inc. (ADA) has completed the bench-scale testing phase of a program to evaluate additives that will improve the collection of fine particles in electrostatic precipitators (ESPs). A bench-scale ESP was installed at the Consolidation Coal Company (CONSOL) combustion research and development facility in Library, PA in order to conduct the evaluation. During a two-week test, four candidate additives were injected into the flue gas ahead of a 100 acfm ESP to determine the effect on fly ash collectability. Two additives were found to reduce the emissions from the ESP. Additives ``C`` and ``D`` performed better than initially anticipated -- reducing emissions initially by 17%. Emissions were reduced by 27% after the ESP was modified by the installation of baffles to minimize sneakage. In addition to the measured improvements in performance, no detrimental effects (i.e., electrode fouling) were observed in the operation of the ESP during the testing. The measures of success identified for the bench-scale phase of the program have been surpassed. Since the additives will affect only non-rapping reentrainment particle losses, it is expected that an even greater improvement in particle collection will be observed in larger-scale ESPs. Therefore, positive results are anticipated during the pilot-scale phase of the program and during a future full-scale demonstration test. A preliminary economic analysis was performed to evaluate the cost of the additive process and to compare its costs against alternative means for reducing emissions from ESPs. The results show that conditioning with additive C at a rate of 0.05% (wt. additive to wt. fly ash) is much less expensive than adding new ESP capacity, and more cost competitive than existing chemical conditioning processes. Preliminary chemical analysis of conditioned fly ash shows that it passes the Toxicity Characteristic Leaching Procedure criteria.

  20. Bench-Scale Synthetic Optimization of 1,2-bis(2-aminophenylthio)ethane (APO-Link) Used in the Production of APO-BMI Resin

    Energy Technology Data Exchange (ETDEWEB)

    Hilary Wheeler; Crystal Densmore

    2007-07-31

    The diamine reagent 1,2-bis(2-aminophenylthio)ethane is no longer commercially available but still required for the synthesis of the bismaleimide resin, APO-BMI, used in syntactic foams. In this work, we examined the hydrolysis of benzothiazole followed the by reaction with dichloroethane or dibromoethane. We also studied the deprotonation of 2-aminothiophenol followed by the reaction with dibromoethane. We optimized the latter for scale-up by scrutinizing all aspects of the reaction conditions, work-up and recrystallization. On bench-scale, our optimized procedure consistently produced a 75-80% overall yield of finely divided, high purity product (>95%).

  1. EVALUATION OF THE TREATABILITY OF MUNICIPAL WASTE LANDFILL LEACHATE IN A SBR AND BY COAGULATION-FLOCCULATION ON A BENCH SCALE

    Directory of Open Access Journals (Sweden)

    E. Fleck

    Full Text Available Abstract This article describes bench scale sequential, biological and coagulation-flocculation treatment of mature leachate for the removal of nitrogen and biodegradable and recalcitrant carbonaceous material. The biological stage was conducted on two SBRs, one of which inoculated with nitrifying sludge, another without an inoculum, for 152 and 133 days, respectively. The coagulation-flocculation stage used four coagulants at different doses and pH adjustments. The treatment conducted on the inoculated SBR when a pH control was used produced mean removals of BOD5, COD and TKN of 69.6%, 38.5% and 51.6%, respectively, and practically complete denitrification. Coagulation-flocculation applied to the effluent of the inoculated biological reactor showed a superior effectiveness of the ferric coagulants, when the pH was adjusted to close to 6.0, producing removals of turbidity, COD and true color close to 95%, 78% and 92%, respectively.

  2. Appling hydrolysis acidification-anoxic–oxic process in the treatment of petrochemical wastewater: From bench scale reactor to full scale wastewater treatment plant

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Changyong [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); Research Center of Water Pollution Control Technology, Chinese Research Academy of Environment Sciences, Beijing 100012 (China); Zhou, Yuexi, E-mail: zhouyuexi@263.net [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); Research Center of Water Pollution Control Technology, Chinese Research Academy of Environment Sciences, Beijing 100012 (China); Sun, Qingliang [School of Chemical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Fu, Liya [Research Center of Water Pollution Control Technology, Chinese Research Academy of Environment Sciences, Beijing 100012 (China); School of Environment, Tsinghua University, Beijing 100084 (China); Xi, Hongbo; Yu, Yin [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); Research Center of Water Pollution Control Technology, Chinese Research Academy of Environment Sciences, Beijing 100012 (China); Yu, Ruozhen [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012 (China)

    2016-05-15

    Highlights: • Hydrolysis acidification-anoxic–oxic process can be used to treat petrochemical wastewater. • The toxicity and treatability changed significantly after hydrolysis acidification. • The type and concentration of organics reduced greatly after treatment. • The effluent shows low acute toxicity by luminescent bacteria assay. • Advanced treatment is recommended for the effluent. - Abstract: A hydrolysis acidification (HA)-anoxic–oxic (A/O) process was adopted to treat a petrochemical wastewater. The operation optimization was carried out firstly by a bench scale experimental reactor. Then a full scale petrochemical wastewater treatment plant (PCWWTP, 6500 m{sup 3} h{sup −1}) was operated with the same parameters. The results showed that the BOD{sub 5}/COD of the wastewater increased from 0.30 to 0.43 by HA. The effluent COD was 54.4 mg L{sup −1} for bench scale reactor and 60.9 mg L{sup −1} for PCWWTP when the influent COD was about 480 mg L{sup −1} on optimized conditions. The organics measured by gas chromatography-mass spectrometry (GC–MS) reduced obviously and the total concentration of the 5 organics (1,3-dioxolane, 2-pentanone, ethylbenzene, 2-chloromethyl-1,3-dioxolane and indene) detected in the effluent was only 0.24 mg L{sup −1}. There was no obvious toxicity of the effluent. However, low acute toxicity of the effluent could be detected by the luminescent bacteria assay, indicating the advanced treatment is needed. The clone library profiling analysis showed that the dominant bacteria in the system were Acidobacteria, Proteobacteria and Bacteriodetes. HA-A/O process is suitable for the petrochemical wastewater treatment.

  3. Appling hydrolysis acidification-anoxic–oxic process in the treatment of petrochemical wastewater: From bench scale reactor to full scale wastewater treatment plant

    International Nuclear Information System (INIS)

    Wu, Changyong; Zhou, Yuexi; Sun, Qingliang; Fu, Liya; Xi, Hongbo; Yu, Yin; Yu, Ruozhen

    2016-01-01

    Highlights: • Hydrolysis acidification-anoxic–oxic process can be used to treat petrochemical wastewater. • The toxicity and treatability changed significantly after hydrolysis acidification. • The type and concentration of organics reduced greatly after treatment. • The effluent shows low acute toxicity by luminescent bacteria assay. • Advanced treatment is recommended for the effluent. - Abstract: A hydrolysis acidification (HA)-anoxic–oxic (A/O) process was adopted to treat a petrochemical wastewater. The operation optimization was carried out firstly by a bench scale experimental reactor. Then a full scale petrochemical wastewater treatment plant (PCWWTP, 6500 m 3 h −1 ) was operated with the same parameters. The results showed that the BOD 5 /COD of the wastewater increased from 0.30 to 0.43 by HA. The effluent COD was 54.4 mg L −1 for bench scale reactor and 60.9 mg L −1 for PCWWTP when the influent COD was about 480 mg L −1 on optimized conditions. The organics measured by gas chromatography-mass spectrometry (GC–MS) reduced obviously and the total concentration of the 5 organics (1,3-dioxolane, 2-pentanone, ethylbenzene, 2-chloromethyl-1,3-dioxolane and indene) detected in the effluent was only 0.24 mg L −1 . There was no obvious toxicity of the effluent. However, low acute toxicity of the effluent could be detected by the luminescent bacteria assay, indicating the advanced treatment is needed. The clone library profiling analysis showed that the dominant bacteria in the system were Acidobacteria, Proteobacteria and Bacteriodetes. HA-A/O process is suitable for the petrochemical wastewater treatment.

  4. Bench-scale testing of on-line control of column flotation using a novel analyzer. Third quarterly technical progress report, April 1, 1993--June 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-24

    This document contains the third quarterly technical progress report for PTI`s Bench-Scale Testing Project of a circuit integrating PTI`s KEN-FLOTETM Column Flotation Technology and PTI`s On-Line Quality Monitor and Control System. The twelve-month project involves installation and testing of a 200--300 lb/hr. bench-scale flotation circuit at PETC`s Coal Preparation Process Research Facility (CPPRF) for two bituminous coals (Upper Freeport and Pittsburgh No. 8 Seam Raw Coals). Figure 1 contains the project plan, as well as the approach to completing the major tasks within the twelve-month project schedule. The project is broken down into three phases, which include: Phase I -- Preparation: The preparation phase was performed principally at PTI`s Calumet offices from October through December, 1992. It involved building of the equipment and circuitry, as well as some preliminary design and equipment testing; Phase II -- ET Circuit Installation and Testing: This installation and testing phase of the project was performed at PETC`s CPPRF from January through June, 1993, and was the major focus of the project. It involved testing of the continuous 200--300 lb/hr. circuit; and Phase III -- Project Finalization: The project finalization phase is occurring from July through September, 1993, at PTI`s Calumet offices and involves finalizing analytical work and data evaluation, as well as final project reporting. This Third Quarterly Technical Progress Report principally summarizes the results from the benchscale testing with the second coal (Pittsburgh No. 8 Seam Coal), which occurred in April through June, 1993. It also contains preliminary economic evaluations that will go into the Final Report, as well as the plan for the final reporting task.

  5. BENCH-SCALE VISUALIZATION OF DNAPL REMEDIATION PROCESSES IN ANALOG HETEROGENEOUS AQUIFERS: SURFACTANT FLOODS, AND IN SITU OXIDATION USING PERMANGANATE

    Science.gov (United States)

    We have conducted well-controlled DNAPL remediation experiments using surfactants (Aerosol MA and Tween 80) to increase solubility and an oxidant (permanganate) to chemically degrade the DNAPL. Photographs and digital image analysis illustrate previously unobserved interactions b...

  6. Production of Jet Fuels from Coal Derived Liquids. Volume 9. Results of Bench-Scale and Pilot Plant Testing

    Science.gov (United States)

    1989-06-01

    Great Plains Coal Gasification Plant in Beulah, North Dakota. Experiments show that the hydroprocessing conditions recommended in Task 1 are not severe...50 REFERENCES. ............................ 51 APPENDIX A: LCI Test Report on Expanded-Bed Al Hydroprocessing of 300*F+ Great Plains Tar ...recovered by gravity separation. The heaviest portion of the tar oil, which contains about 20 percent coal dust, is recycled to the gasifiers. The recycle

  7. TDT-3R Clean Multi Fuels. ECN contribution to WP3. Lab-/bench-scale pyrolysis test of biomass and analysis of byproducts

    International Nuclear Information System (INIS)

    Bos, A.; Oudhuis, A.B.J.; Zwart, R.W.R.; Boersma, A.R.

    2005-11-01

    Under the present conditions it is expected that coal will still be used for a long period as a energy source. Furthermore, biomass is emerging as a new renewable CO2-neutral energy source in the future. Both fuels need significantly lower emissions to meet new (future) European Union environmental norms for sustainable clean energy production. Several technologies and 'end-of pipe' solutions have been developed in the past to reach these stricter emission limits. Examples are integrated combined cycle gasification systems (IGCC) for large scale use (>250 MW capacity). Also, a large number of gas cleaning technologies have been developed. These technologies are up-to-now rather complicated and/or costly and therefore also new solutions have to be developed. The 3R Multifuel process is aimed to offer a solution to these problems, especially for low-rank coals like brown coal, lignite, high sulfur coal, derived fuels and biomass. The objectives for ECN in the Work Package 3 of this project are: (a) to summarise and update data for the potential of biomass and waste streams in Europe for power production; and (b) to select biomass/waste streams to be tested in the lab/bench-scale facility and to generate design data for clean solid fuel production from biomass to be used for a pilot facility in Hungary. TDT-3R stands for Thermal Desorption Technology-Recycle-Reduce-Reuse

  8. Flexible Bench-Scale Recirculating Flow CPC Photoreactor for Solar Photocatalytic Degradation of Methylene Blue Using Removable TiO2 Immobilized on PET Sheets

    Directory of Open Access Journals (Sweden)

    Doaa M. EL-Mekkawi

    2016-01-01

    Full Text Available TiO2 immobilized on polyethylene (PET nonwoven sheet was used in the solar photocatalytic degradation of methylene blue (MB. TiO2 Evonik Aeroxide P25 was used in this study. The amount of loaded TiO2 on PET was approximately 24%. Immobilization of TiO2 on PET was conducted by dip coating process followed by exposing to mild heat and pressure. TiO2/PET sheets were wrapped on removable Teflon rods inside home-made bench-scale recirculating flow Compound Parabolic Concentrator (CPC photoreactor prototype (platform 0.7 × 0.2 × 0.4 m3. CPC photoreactor is made up of seven low iron borosilicate glass tubes connected in series. CPC reflectors are made of stainless steel 304. The prototype was mounted on a platform tilted at 30°N local latitude in Cairo. A centrifugal pump was used to circulate water containing methylene blue (MB dye inside the glass tubes. Efficient photocatalytic degradation of MB using TiO2/PET was achieved upon the exposure to direct sunlight. Chemical oxygen demand (COD analyses reveal the complete mineralization of MB. Durability of TiO2/PET composite was also tested under sunlight irradiation. Results indicate only 6% reduction in the amount of TiO2 after seven cycles. No significant change was observed for the physicochemical characteristics of TiO2/PET after the successive irradiation processes.

  9. Characterization of mercury, arsenic, and selenium in the product streams of a bench-scale, inert-gas, oil shale retort

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, K.B.; Evans, J.C.; Fruchter, J.S.; Girvin, D.C.; Nelson, C.L. (Pacific Northwest Lab., Richland, WA (USA))

    1990-02-01

    The purpose of this study was to determine the effects of heating rates and maximum temperatures on the redistribution of mercury, arsenic, and selenium into the shale oil, retort water, and offgas of a 6-kg bench-scale retort. A Green River shale (western) from Colorado and a New Albany shale (eastern) from Kentucky were heated at 1-2{degree}C/min to a maximum temperature of 500{degree}C. The eastern and western shales were also heated at 2{degree}C/min to 750{degree}C and at 10{degree}C/min to 750{degree}C. Real-time monitoring of the offgas stream for mercury was accomplished with Zeeman atomic absorption spectroscopy or a microwave-induced helium plasma spectroscopy. Microwave-induced helium plasma spectroscopy was also used to monitor for arsenic in the offgas during retorting; little or no arsenic was observed in the offgas. Mass balance calculations for arsenic and selenium accounted for essentially 100% of those elements in the spent shale, shale oil, and retort water. The mass balance calculations suggest little offgas component for arsenic and selenium. This agrees with the results of the MPD monitoring of the offgas. These results indicate the potential pathway for mercury to enter the environment is from the offgas. Arsenic and selenium preferential redistribution into the shale oil may present problems during the upgrading process.

  10. Influence of toluene and salinity on biosurfactant production by Bacillus sp.: scale up from flasks to a bench-scale bioreactor

    Directory of Open Access Journals (Sweden)

    Ellen Cristina Souza

    Full Text Available ABSTRACT To select the best biosurfactant producer, Pseudomonas putida, Bacillus megatherium, Bacillus licheniformis and Bacillus subtilis were cultured in flasks on media with different salinity [low salinity (LS, Bushnell-Haas (BH and artificial sea water (SW media] supplemented or not with toluene as a model pollutant. Toluene inhibited the growth of all microorganisms and stimulated the biosurfactant production. B. subtilis exhibited the best performance, being able to lower the surface tension (ST in the LS medium to 65.5 mN/min in the absence of toluene, and to 46.5 mN/min in the BH medium in the presence of toluene, corresponding to ST reductions of 13.0 and 27.5 mN/m, respectively. Scaling up the process to a bench-scale fermentor, the best results were obtained in the LS medium, where B. subtilis was able to reduce the toluene concentration from 26.0 to 4.3 g/L within 12 h and ST by 17.2 mN/m within 18 h. The results of this study point out that B. subtilis is an interesting biosurfactant producer, which could be used in the bioremediation of toluene-contaminated water.

  11. Bench Scale Process for Low Cost CO2 Capture Using a Phase-Changing Absorbent: Topical Report EH&S Risk Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Westendorf, Tiffany; Farnum, Rachel; Perry, Robert; Herwig, Mark; Giolando, Salvatore; Green, Dianne; Morall, Donna

    2016-05-11

    GE Global Research was contracted by the Department of Energy to design and build a bench-scale process for a novel phase-changing aminosilicone-based CO2 capture solvent (award number DEFE0013687). As part of this program, a technology EH&S assessment (Subtask 5.1) has been completed for a CO2 capture system for a 550 MW coal-fired power plant. The assessment focuses on two chemicals used in the process, the aminosilicone solvent, GAP-0, and dodecylbenzenesulfonic acid (DDBSA), the GAP-0 carbamate formed upon reaction of the GAP-0 with CO2, and two potential byproducts formed in the process, GAP-0/SOx salts and amine-terminated, urea-containing silicone (also referred to as “ureas” in this report). The EH&S assessment identifies and estimates the magnitude of the potential air and water emissions and solid waste generated by the process and reviews the toxicological profiles of the chemicals associated with the process. Details regarding regulatory requirements, engineering controls, and storage and handling procedures are also provided in the following sections.

  12. Characterization of L-asparaginase from marine-derived Aspergillus niger AKV-MKBU, its antiproliferative activity and bench scale production using industrial waste.

    Science.gov (United States)

    Vala, Anjana K; Sachaniya, Bhumi; Dudhagara, Dushyant; Panseriya, Haresh Z; Gosai, Haren; Rawal, Rakesh; Dave, Bharti P

    2018-03-01

    L-asparaginase (LA), an enzyme with anticancer activities, produced by marine-derived Aspergillus niger was subjected to purification and characterization. The purified enzyme was observed to have molecular weight ∼90KDa. The enzyme retained activity over a wide range of pH, i.e. pH 4-10. The enzyme was quite stable in temperature range 20-40°C. Tween 80 and Triton X-100 were observed to enhance LA activity while inhibition of LA activity was observed in presence of heavy metals. The values for K m was found to be 0.8141 mM and V max was 6.228μM/mg/min. The enzyme exhibited noteworthy antiproliferative activity against various cancer cell lines tested. Successful bench scale production (in 5L bioreacator) of LA using groundnut oil cake as low cost substrate has also been carried out. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Integrating a 250 mL-spinner flask with other stirred bench-scale cell culture devices: a mass transfer perspective.

    Science.gov (United States)

    Vallejos, Jose R; Brorson, Kurt A; Moreira, Antonio R; Rao, Govind

    2011-01-01

    The bioprocess development cycle is a complex task that requires a complete understanding of the engineering of the process (e.g., mass transfer, mixing, CO(2) removal, process monitoring, and control) and its affect on cell biology and product quality. Despite their widespread use in bioprocess development, spinner flasks generally lack engineering characterization of critical physical parameters such as k(L)a, P/V, or mixing time. In this study, mass transfer characterization of a 250-mL spinner flask using optical patch-based sensors is presented. The results quantitatively show the effect of the impeller type, liquid filling volume, and agitation speed on the volumetric mass transfer coefficient (k(L)a) in a 250-mL spinner flask, and how they can be manipulated to match mass transfer capability at large culture devices. Thus, process understanding in spinner flasks can be improved, and these devices can be seamlessly integrated in a rational scale-up strategy from cell thawing to bench-scale bioreactors (and beyond) in biomanufacturing. Copyright © 2011 American Institute of Chemical Engineers (AIChE).

  14. Determination and modeling of the influence of the fluid-dynamics in hydro-treating bench scale plants

    Energy Technology Data Exchange (ETDEWEB)

    Burkhardt, T.

    1999-09-16

    At an industrial scale, the hydro-treating of oil fractions is carried out in multiphase fixed bed reactors. The oil and hydrogen cross the catalyst bed, usually in co-current downflow. Since the product specifications are steadily becoming more severe, the testing of new catalysts and of modified operating conditions in pilot plants becomes increasingly important. Although these pilot plants are frequently by a factor of 100 000 smaller than the industrial units, they still have to allow the up-scaling to industrial units. In the literature relatively low conversion degrees in pilot plants are frequently reported, especially in downflow. The significantly lower fluid velocities in pilot plants seem to be responsible for such differences, as the influence of fluid-dynamic non-idealities and of the extra-particle mass transfer phenomena increases with a decrease of the fluid velocities. In the present work, the influence of important fluid-dynamic non-idealities on the hydro-treating of gas oil fractions in pilot plants was examined. This was done on the one hand in experiments with different pilot plants and on the other hand by simulations with an especially developed multiphase model. The phenomena were considered as well in an isolated manner. In order to examine any interactions with the chemical reactions, they were also studied in a reactive system. This methodology was applied to the phenomena, 'axial dispersion'and 'gas-liquid mass transfer'. (author)

  15. Removal of strontium from drinking water by conventional treatment and lime softening in bench-scale studies.

    Science.gov (United States)

    O'Donnell, Alissa J; Lytle, Darren A; Harmon, Stephen; Vu, Kevin; Chait, Hannah; Dionysiou, Dionysios D

    2016-10-15

    The United States Environmental Protection Agency Contaminant Candidate List 3 lists strontium as a contaminant for potential regulatory consideration in drinking water. Very limited data is available on strontium removal from drinking water and as a result, there is an immediate need for treatment information. The objective of this work is to evaluate the effectiveness of coagulation/filtration and lime-soda ash softening treatment methods to remove strontium from surface and ground waters. Coagulation/filtration jar test results on natural waters showed that conventional treatment with aluminum and iron coagulants were able to achieve only 12% and 5.9% strontium removal, while lime softening removed as high as 78% from natural strontium-containing ground water. Controlled batch experiments on synthetic water showed that strontium removal during the lime-soda ash softening was affected by pH, calcium concentration and dissolved inorganic carbon concentration. In all softening jar tests, the final strontium concentration was directly related to the initial strontium concentration and the removal of strontium was directly associated with calcium removal. Precipitated solids showed well-formed crystals or agglomerates of mixed solids, two polymorphs of calcium carbonate (vaterite and calcite), and strontianite, depending on initial water quality conditions. X-ray diffraction analysis suggested that strontium was likely incorporated in the calcium carbonate crystal lattice and was likely responsible for removal during lime softening. Copyright © 2016. Published by Elsevier Ltd.

  16. Hydrogen production with short contact time. Catalytic partial oxidation of hydrocarbons and oxygenated compounds: Recent advances in pilot- and bench-scale testing and process design

    Energy Technology Data Exchange (ETDEWEB)

    Guarinoni, A.; Ponzo, R.; Basini, L. [ENI Refining and Marketing Div., San Donato Milanese (Italy)

    2010-12-30

    ENI R and D has been active for fifteen years in the development of Short Contact Time - Catalytic Partial Oxidation (SCT-CPO) technologies for producing Hydrogen/Synthesis Gas. From the beginning the experimental work addressed either at defining the fundamental principles or the technical and economical potential of the technology. Good experimental responses, technical solutions' simplicity and flexibility, favourable techno-economical evaluations promoted the progressive widening of the field of the investigations. From Natural Gas (NG) the range of ''processable'' Hydrocarbons extended to Liquefied Petroleum Gas (LPG) and Gasoils, including those characterised by high levels of unsaturated and sulphurated molecules and, lately, to other compounds with biological origin. The extensive work led to the definition of different technological solutions, grouped as follows: Technology 1: Air Blown SCT-CPO of Gaseous Hydrocarbons and/or Light Compounds with biological origin Technology 2: Enriched Air/Oxygen Blown SCT-CPO of Gaseous Hydrocarbons and/or Light Compounds with biological origin Technology 3: Enriched Air/Oxygen Blown SCT-CPO of Liquid Hydrocarbons and/or Compounds with biological origin Recently, the licence rights on a non-exclusive basis for the commercialisation of SCT-CPO based processes for H{sub 2}/Synthesis gas production from light hydrocarbons with production capacity lower than 5,000 Nm{sup 3}/h of H{sub 2} or 7,500 Nm3/h of syngas have been assigned to two external companies. In parallel, development of medium- and large-scale plant solutions is progressing within the ENI group framework. These last activities are addressed to the utilisation of SCT-CPO for matching the variable Hydrogen demand in several contexts of oil refining operation. This paper will report on the current status of SCT-CPO with a focus on experimental results obtained, either at pilot- and bench- scale level. (orig.)

  17. Hydrogen generation from bioethanol reforming: bench-scale unit performance with Cu/Nb{sub 2}O{sub 5} catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes Machado, N.R.C. [State Univ. of Maringa (UEM), Chemical Engineering Dept., Lab. of Catalysis, Maringa (Brazil); Schmal, M. [PEQ/COPPE/UFRJ Cidade Univ., Centro de Tecnologia, Graduate School and Research in Engineering Alberto Luiz Coimbra Institute, Rio De Janeiro (Brazil); Cantao, M.P. [LACTEC, Dept. of Materials, Inst. of Technology for Development, Curitiba (Brazil)] [and others

    2003-07-01

    As an alternative route for hydrogen production, ethanol reforming was studied in a bench-scale unit using a 5%Cu/Nb{sub 2}O{sub 5} catalyst previously selected in a micro reactor. X-Ray Diffraction analysis has shown that this catalyst contains copper oxide in an amorphous form, or in particles smaller than 20 nm, while the Nb{sub 2}O{sub 5} is highly crystalline. Analysis of the calcinated catalyst by X-Ray Photoelectron Spectroscopy revealed that 35% of total copper was on the surface as Cu{sup I} (55%) or Cu{sup II} (45%). The catalyst presented a low surface area (35 m{sup 2}/g), mainly from meso and macropores, as textural analysis revealed. Temperature Programmed Reduction showed a two-step reduction of Cu{sup II} to Cu, at 245{sup o}C and 306{sup o}C. It was also observed the reduction of 6% of Nb{sub 2}O{sub 5}. The reaction unit consisted of an integral reactor with 16 g of catalyst pellets, approximately 3 mm x 5 mm in size. Reaction temperature and feed rate were varied to optimize hydrogen production, with CO{sub 2} as the main byproduct. Reagents (water and ethanol) in stoichiometric proportion were fed into an electric pre-heater and vaporized. An increase on reaction temperature from 300{sup o}C to 400{sup o}C has led to an increase in mean conversion from 17% to 35%. Ethene and ethyl ether were also detected as minor byproducts. (author)

  18. Bench Scale Process for Low Cost CO2 Capture Using a PhaseChanging Absorbent: Techno-Economic Analysis Topical Report

    Energy Technology Data Exchange (ETDEWEB)

    Miebach, Barbara [GE Global Research, Niskayuna, New York (United States); McDuffie, Dwayne [GE Global Research, Niskayuna, New York (United States); Spiry, Irina [GE Global Research, Niskayuna, New York (United States); Westendorf, Tiffany [GE Global Research, Niskayuna, New York (United States)

    2017-01-27

    The objective of this project is to design and build a bench-scale process for a novel phase-changing CO2 capture solvent. The project will establish scalability and technical and economic feasibility of using a phase-changing CO2 capture absorbent for post-combustion capture of CO2 from coal-fired power plants with 90% capture efficiency and 95% CO2 purity at a cost of $40/tonne of CO2 captured by 2025 and a cost of <$10/tonne of CO2 captured by 2035. This report presents system and economic analysis for a process that uses a phase changing aminosilicone solvent to remove CO2 from pulverized coal (PC) power plant flue gas. The aminosilicone solvent is a pure 1,3-bis(3-aminopropyl)-1,1,3,3-tetramethyldisiloxane (GAP-0). Performance of the phase-changing aminosilicone technology is compared to that of a conventional carbon capture system using aqueous monoethanolamine (MEA). This analysis demonstrates that the aminosilicone process has significant advantages relative to an MEA-based system. The first-year CO2 removal cost for the phase-changing CO2 capture process is $52.1/tonne, compared to $66.4/tonne for the aqueous amine process. The phase-changing CO2 capture process is less costly than MEA because of advantageous solvent properties that include higher working capacity, lower corrosivity, lower vapor pressure, and lower heat capacity. The phase-changing aminosilicone process has approximately 32% lower equipment capital cost compared to that of the aqueous amine process. However, this solvent is susceptible to thermal degradation at CSTR desorber operating temperatures, which could add as much as $88/tonne to the CO2 capture cost associated with solvent makeup. Future work is focused on mitigating this critical risk by developing an advanced low-temperature desorber that can deliver comparable desorption performance and significantly reduced

  19. The effects of physical separtation treatment on the removal of uranium from contaminated soils at Fernald: A bench-scale study

    International Nuclear Information System (INIS)

    Sadler, K.G.; Krstich, M.A.

    1994-01-01

    A bench-scale treatability study incorporating the use of physical separation techniques and chemical dispersants/extractants was conducted on uranium contaminated soils at the Fernald Environmental Management Project (FEMP) site. The soils contained approximately 497 and 450 milligrams per kilogram (mg/kg) of total uranium, respectively. Geotechnical characterization indicated that 77.4 and 74.6 percent of the soil was in the less that 50 micrometer (μm) size fraction for the ID-A and ID-B soils, respectively. An initial characterization effort indicated that uranium was distributed among all particle size fractions. After each soil was dispersed in water, it was noted that the uranium concentrated in the sand and clay fractions for the ID-A soil (1028 and 1475 mg kg -1 , respectively) and the clay fraction for ID-B soil (2710 mg kg -1 ). Four 1 millimolar (mM) sodium reagent solutions (sodium hydroxide, sodium carbonate, sodium bicarbonate, and a sodium citrate-bicarbonate-dithionite mixture) and potable water were evaluated for effectiveness in dispersing each soil into single grain separates and extracting total uranium from each of the resulting particle size fractions. Dilute sodium solutions were more effective than water in dispersing the soil. The use of dispersants, as compared to water, on the less than 2 mm size fraction causes a shift in the distribution of uranium out of the sand fraction and into the silt and clay fractions for ID-A soil and into the clay fraction for the ID-B soil. Attrition scrubbing tests were conducted on the less than 2 mm size fraction for the ID-A and ID-B soils using water and three alkaline extraction solutions, sodium pyrophosphate, sodium carbonate/bicarbonate, and ammonium carbonate/bicarbonate. There was little difference among the chemical extractants on their effectiveness in removing uranium from the greater than 53 μm (sand) or less than 53 μm (silt and clay) soil fraction

  20. Bench-scale Development of an Advanced Solid Sorbent-based CO2 Capture Process for Coal-fired Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Thomas [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Kataria, Atish [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Soukri, Mustapha [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Farmer, Justin [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Mobley, Paul [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Tanthana, Jak [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Wang, Dongxiang [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Wang, Xiaoxing [Research Triangle Institute (RTI), Research Triangle Park, NC (United States); Song, Chunshan [Research Triangle Institute (RTI), Research Triangle Park, NC (United States)

    2015-12-31

    It is increasingly clear that CO2 capture and sequestration (CCS) must play a critical role in curbing worldwide CO2 emissions to the atmosphere. Development of these technologies to cost-effectively remove CO2 from coal-fired power plants is very important to mitigating the impact these power plants have within the world’s power generation portfolio. Currently, conventional CO2 capture technologies, such as aqueous-monoethanolamine based solvent systems, are prohibitively expensive and if implemented could result in a 75 to 100% increase in the cost of electricity for consumers worldwide. Solid sorbent CO2 capture processes – such as RTI’s Advanced Solid Sorbent CO2, Capture Process – are promising alternatives to conventional, liquid solvents. Supported amine sorbents – of the nature RTI has developed – are particularly attractive due to their high CO2 loadings, low heat capacities, reduced corrosivity/volatility and the potential to reduce the regeneration energy needed to carry out CO2 capture. Previous work in this area has failed to adequately address various technology challenges such as sorbent stability and regenerability, sorbent scale-up, improved physical strength and attrition-resistance, proper heat management and temperature control, proper solids handling and circulation control, as well as the proper coupling of process engineering advancements that are tailored for a promising sorbent technology. The remaining challenges for these sorbent processes have provided the framework for the project team’s research and development and target for advancing the technology beyond lab- and bench-scale testing. Under a cooperative agreement with the US Department of Energy, and part of NETL’s CO2 Capture Program, RTI has led an effort to address and mitigate the challenges associated with solid sorbent CO2 capture. The overall objective

  1. Hierarchical calibration and validation framework of bench-scale computational fluid dynamics simulations for solvent-based carbon capture. Part 2: Chemical absorption across a wetted wall column: Original Research Article: Hierarchical calibration and validation framework of bench-scale computational fluid dynamics simulations

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Chao [Pacific Northwest National Laboratory, Physical and Computational Sciences Directorate, Richland WA; Xu, Zhijie [Pacific Northwest National Laboratory, Physical and Computational Sciences Directorate, Richland WA; Lai, Kevin [Pacific Northwest National Laboratory, Physical and Computational Sciences Directorate, Richland WA; Whyatt, Greg [Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland WA; Marcy, Peter W. [Los Alamos National Laboratory, Statistical Sciences Group, Los Alamos NM; Sun, Xin [Oak Ridge National Laboratory, Energy and Transportation Science Division, Oak Ridge TN

    2017-10-24

    The first part of this paper (Part 1) presents a numerical model for non-reactive physical mass transfer across a wetted wall column (WWC). In Part 2, we improved the existing computational fluid dynamics (CFD) model to simulate chemical absorption occurring in a WWC as a bench-scale study of solvent-based carbon dioxide (CO2) capture. To generate data for WWC model validation, CO2 mass transfer across a monoethanolamine (MEA) solvent was first measured on a WWC experimental apparatus. The numerical model developed in this work has the ability to account for both chemical absorption and desorption of CO2 in MEA. In addition, the overall mass transfer coefficient predicted using traditional/empirical correlations is conducted and compared with CFD prediction results for both steady and wavy falling films. A Bayesian statistical calibration algorithm is adopted to calibrate the reaction rate constants in chemical absorption/desorption of CO2 across a falling film of MEA. The posterior distributions of the two transport properties, i.e., Henry’s constant and gas diffusivity in the non-reacting nitrous oxide (N2O)/MEA system obtained from Part 1 of this study, serves as priors for the calibration of CO2 reaction rate constants after using the N2O/CO2 analogy method. The calibrated model can be used to predict the CO2 mass transfer in a WWC for a wider range of operating conditions.

  2. EVALUATION OF SOIL WASHING TECHNOLOGY: RESULTS OF BENCH SCALE EXPERIMENTS ON PETROLEUM FUELS CONTAMINATED SOILS - EPA/600/S2-91/023

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) through its Risk Reduction Engineering Laboratory's Release Control Branch has undertaken research and development efforts to address the problem of leaking underground storage tanks (USTs). Under this effort, EPA is currently eva...

  3. Bench-Scale Study of Hydrogen Separation Using Pre-Commercial Membranes; Estudio, a Escala de Planta Piloto, del Proceso de Separacion de Hidrogeno mediante Membranas Pre-Comerciales

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez Hervas, J. M.; Marano, M.

    2011-11-10

    This report compiles the research undertaken by CIEMAT over 2009-2011 in the sub-project 8 Purification and Separation of Hydrogen of the PSE H2ENOV Project funded by the Spanish Ministry of Science and Innovation, MICINN. Permeability and hydrogen selectivity of a pre-commercial palladium membrane was studied at bench scale level. The effect of main operating parameters - pressure, temperature and feed-flow-rate- on permeate flow-rate was determined. The influence of other gas components on hydrogen permeation was evaluated. Mixtures of H{sub 2}-N{sub 2} and H{sub 2}-CO{sub 2} were studied. Although nitrogen and carbon dioxide did not permeate, both components decreased hydrogen permeation rate. Operating the membrane for around 1000 h under various conditions showed a small decrease in hydrogen permeation, but not in selectivity. A literature review was done in order to identify causes for permeation inhibition and reduction and for the definition of procedures for membrane regeneration. (Author) 29 refs.

  4. THOR Bench-Scale Steam Reforming Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    D. W. Marshall; N. R. Soelberg; K. M. Shaber

    2003-05-01

    The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by THORsm Treatment Technologies, LLC, for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrates were not detected in the product and NOx destruction exceeded 98%. The demonstration was successful.

  5. TWR Bench-Scale Steam Reforming Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, D.W.; Soelberg, N.R.

    2003-05-21

    The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by ThermoChem Waste Remediation, LLC, (TWR) for treatment of SBW into a ''road ready'' waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). TWR is the licensee of Manufacturing Technology Conservation International (MTCI) steam-reforming technology in the field of radioactive waste treatment. A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrate residues were about 400 ppm in the product and NOx destruction exceeded 86%. The demonstration was successful.

  6. TWR Bench-Scale Steam Reforming Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    D. W. Marshall; N. R. Soelberg

    2003-05-01

    The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by ThermoChem Waste Remediation, LLC, (TWR) for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). TWR is the licensee of Manufacturing Technology Conservation International (MTCI) steam-reforming technology in the field of radioactive waste treatment. A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrate residues were about 400 ppm in the product and NOx destruction exceeded 86%. The demonstration was successful.

  7. THOR Bench-Scale Steam Reforming Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, D.W.; Soelberg, N.R.; Shaber, K.M.

    2003-05-21

    The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by THORsm Treatment Technologies, LLC, for treatment of SBW into a ''road ready'' waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrates were not detected in the product and NOx destruction exceeded 98%. The demonstration was successful.

  8. THOR Bench-Scale Steam Reforming Demonstration

    International Nuclear Information System (INIS)

    Marshall, D.W.; Soelberg, N.R.; Shaber, K.M.

    2003-01-01

    The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by THORsm Treatment Technologies, LLC, for treatment of SBW into a ''road ready'' waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrates were not detected in the product and NOx destruction exceeded 98%. The demonstration was successful

  9. Polymeric Traypack Integrity: Bench-Scale Unit

    National Research Council Canada - National Science Library

    Canavan, Jeffrey

    2002-01-01

    .... Additional experimentation was conducted to determine the applicability of the unit for non-destructive residual gas testing since current destructive tests represent a substantial continuing expense...

  10. Surfactant studies for bench-scale operation

    Science.gov (United States)

    Hickey, Gregory S.; Sharma, Pramod K.

    1993-01-01

    A phase 2 study has been initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This report covers the second quarter of work. The major accomplishments were: completion of coal liquefaction autoclave reactor runs with Illinois number 6 coal at processing temperatures of 300, 325, and 350 C, and pressures of 1800 psig; analysis of the filter cake and the filtrate obtained from the treated slurry in each run; and correlation of the coal conversions and the liquid yield quality to the surfactant concentration. An increase in coal conversions and upgrading of the liquid product quality due to surfactant addition was observed for all runs.

  11. Bench Scale Saltcake Dissolution Test Report

    International Nuclear Information System (INIS)

    BECHTOLD, D.B.; PACQUET, E.A.

    2000-01-01

    A potential scenario for retrieving saltcake from single shell tanks is the ''Rainbird(reg s ign) sprinkler'' method. Water is distributed evenly across the surface of the saltcake and allowed to percolate by gravity through the waste. The salt dissolves in the water, forming a saturated solution. The saturated liquid is removed by a saltwell pump situated near the bottom of the tank. By this method, there is never a large inventory of liquid in the tank that could pose a threat of leakage. There are many variables or factors that can influence the hydrodynamics of this retrieval process. They include saltcake porosity; saltwell pumping rate; salt dissolution chemistry; factors that could promote flow channeling (e.g. tank walls, dry wells, inclusions or discontinuities in the saltcake); method of water distribution; plug formation due to crystal formations or accumulation of insoluble solids. A brief literature search indicates that very little experimental data exist on these aspects of saltcake dissolution (Wiersma 1996, 1997). The tests reported here were planned (Herting, 2000) to provide preliminary data and information for planning future, scaled-up tests of the sprinkler method

  12. Eficiencia del proceso de lavado en la obtención del citrato de calcio y magnesio a escala de banco Effectiveness of washout process to obtain calcium and magnesium citrate at bench scale

    Directory of Open Access Journals (Sweden)

    Jorge E Rodríguez Chanfrau

    2010-03-01

    Full Text Available Como parte de la optimización del proceso tecnológico para obtener citrato de calcio y magnesio a partir de dolomitas, se estudió a escala de banco la etapa de lavado para disminuir el contenido de ácido cítrico libre. Las variantes de lavado estudiadas permitieron disminuir el contenido de ácido cítrico libre por debajo del 3 %, mientras que los valores de calcio y magnesio son similares a los del lote antes de realizar el proceso de lavado. Por otro lado, el estudio toxicológico en ratas, comprobó que los lotes a los cuales se les aplicó las diferentes variantes de lavado no provocaron irritabilidad gástrica a las dosis de 2 000 mg/kg de peso corporal, por lo que se puede afirmar que el proceso de lavado establecido es adecuado para garantizar la calidad de la materia prima.As part of the technological process optomization to obtain calcium citrate and magnesium from dolomites, we studied at bench scale, the washout stage to decrease the free citric acid content. Washout variants allowed to decrease the free citric acid content under 3 %, whereas the calcium and magnesium values are similar to those of batch before to carry out the wahout process. On the other hand, toxicity study in rats, proved that the batches where different washout variables were applied not provoke gastric irritability at doses of 2 000 mg/kg of body weight confirming that above mentioned established process is approproate to guarantee the raw material quality.

  13. SUPERFUND TREATABILITY CLEARINGHOUSE: CERCLA BDAT SARM PREPARATION AND RESULTS OF PHYSICAL SOILS WASHING EXPERIMENTS (FINAL REPORT)

    Science.gov (United States)

    This study reports on the results of work preparing 30,000 Ibs of SARM or synthetic analytical reference matrix, a surrogate Superfund soil containing a vide range of contaminants. It also reports the results ©f bench scale treatability experiments designed to simulate the EP...

  14. 100 Area soil washing bench-scale test procedures

    International Nuclear Information System (INIS)

    Freeman, H.D.; Gerber, M.A.; Mattigod, S.V.; Serne, R.J.

    1993-03-01

    This document describes methodologies and procedures for conducting soil washing treatability tests in accordance with the 100 Area Soil Washing Treatability Test Plan (DOE-RL 1992, Draft A). The objective of this treatability study is to evaluate the use of physical separation systems and chemical extraction methods as a means of separating chemically and radioactively contaminated soil fractions from uncontaminated soil fractions. These data will be primarily used for determining feasibility of the individual unit operations and defining the requirements for a system, or systems, for pilot-scale testing

  15. Modified IRC bench-scale arc melter for waste processing

    International Nuclear Information System (INIS)

    Eddy, T.L.; Sears, J.W.; Grandy, J.D.; Kong, P.C.; Watkins, A.D.

    1994-03-01

    This report describes the INEL Research Center (IRC) arc melter facility and its recent modifications. The arc melter can now be used to study volatilization of toxic and high vapor pressure metals and the effects of reducing and oxidizing (redox) states in the melt. The modifications include adding an auger feeder, a gas flow control and monitoring system, an offgas sampling and exhaust system, and a baghouse filter system, as well as improving the electrode drive, slag sampling system, temperature measurement and video monitoring and recording methods, and oxidation lance. In addition to the volatilization and redox studies, the arc melter facility has been used to produce a variety of glass/ceramic waste forms for property evaluation. Waste forms can be produced on a daily basis. Some of the melts performed are described to illustrate the melter's operating characteristics

  16. Thymol Hydrogenation in Bench Scale Trickle Bed Reactor

    Czech Academy of Sciences Publication Activity Database

    Dudas, J.; Hanika, Jiří; Lepuru, J.; Barkhuysen, M.

    2005-01-01

    Roč. 19, č. 3 (2005), s. 255-262 ISSN 0352-9568 Institutional research plan: CEZ:AV0Z40720504 Keywords : thymol hydrogenation * trickle bed reactor * gas-liquid-solid reaction Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.632, year: 2005

  17. Bench-scale/field-scale interpretations: Session overview

    International Nuclear Information System (INIS)

    Cunningham, A.B.; Peyton, B.M.

    1995-04-01

    In situ bioremediation involves complex interactions between biological, chemical, and physical processes and requires integration of phenomena operating at scales ranging from that of a microbial cell (10 -6 ) to that of a remediation site (10 to 1000 m). Laboratory investigations of biodegradation are usually performed at a relatively small scale, governed by convenience, cost, and expedience. However, extending the results from a laboratory-scale experimental system to the design and operation of a field-scale system introduces (1) additional mass transport mechanisms and limitations; (2) the presence of multiple phases, contants, and competing microorganisms (3) spatial geologic heterogeneities; and (4) subsurface environmental factors that may inhibit bacterial growth such as temperature, pH, nutrient, or redox conditions. Field bioremediation rates may be limited by the availability of one of the necessary constituents for biotransformation: substrate, contaminant, electron acceptor, nutrients, or microorganisms capable of degrading the target compound. The factor that limits the rate of bioremediation may not be the same in the laboratory as it is in the field, thereby leading, to development of unsuccessful remediation strategies

  18. Extended Dry Storage Signature Bench Scale Detector Conceptual Design

    Energy Technology Data Exchange (ETDEWEB)

    Rauch, Eric Benton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-09-02

    This report is the conceptual design of a detector based on research within the Extended Dry Storage Signature Development project under the DOE-­NE MPACT campaign. This is the second year of the project; from this year’s positive results, the next step is building a prototype and testing with real materials .

  19. Goethite Bench-scale and Large-scale Preparation Tests

    Energy Technology Data Exchange (ETDEWEB)

    Josephson, Gary B.; Westsik, Joseph H.

    2011-10-23

    The Hanford Waste Treatment and Immobilization Plant (WTP) is the keystone for cleanup of high-level radioactive waste from our nation's nuclear defense program. The WTP will process high-level waste from the Hanford tanks and produce immobilized high-level waste glass for disposal at a national repository, low activity waste (LAW) glass, and liquid effluent from the vitrification off-gas scrubbers. The liquid effluent will be stabilized into a secondary waste form (e.g. grout-like material) and disposed on the Hanford site in the Integrated Disposal Facility (IDF) along with the low-activity waste glass. The major long-term environmental impact at Hanford results from technetium that volatilizes from the WTP melters and finally resides in the secondary waste. Laboratory studies have indicated that pertechnetate ({sup 99}TcO{sub 4}{sup -}) can be reduced and captured into a solid solution of {alpha}-FeOOH, goethite (Um 2010). Goethite is a stable mineral and can significantly retard the release of technetium to the environment from the IDF. The laboratory studies were conducted using reaction times of many days, which is typical of environmental subsurface reactions that were the genesis of this new process. This study was the first step in considering adaptation of the slow laboratory steps to a larger-scale and faster process that could be conducted either within the WTP or within the effluent treatment facility (ETF). Two levels of scale-up tests were conducted (25x and 400x). The largest scale-up produced slurries of Fe-rich precipitates that contained rhenium as a nonradioactive surrogate for {sup 99}Tc. The slurries were used in melter tests at Vitreous State Laboratory (VSL) to determine whether captured rhenium was less volatile in the vitrification process than rhenium in an unmodified feed. A critical step in the technetium immobilization process is to chemically reduce Tc(VII) in the pertechnetate (TcO{sub 4}{sup -}) to Tc(Iv)by reaction with the ferrous ion, Fe{sup 2+}-Fe{sup 2+} is oxidized to Fe{sup 3+} - in the presence of goethite seed particles. Rhenium does not mimic that process; it is not a strong enough reducing agent to duplicate the TcO{sub 4}{sup -}/Fe{sup 2+} redox reactions. Laboratory tests conducted in parallel with these scaled tests identified modifications to the liquid chemistry necessary to reduce ReO{sub 4}{sup -} and capture rhenium in the solids at levels similar to those achieved by Um (2010) for inclusion of Tc into goethite. By implementing these changes, Re was incorporated into Fe-rich solids for testing at VSL. The changes also changed the phase of iron that was in the slurry product: rather than forming goethite ({alpha}-FeOOH), the process produced magnetite (Fe{sub 3}O{sub 4}). Magnetite was considered by Pacific Northwest National Laboratory (PNNL) and VSL to probably be a better product to improve Re retention in the melter because it decomposes at a higher temperature than goethite (1538 C vs. 136 C). The feasibility tests at VSL were conducted using Re-rich magnetite. The tests did not indicate an improved retention of Re in the glass during vitrification, but they did indicate an improved melting rate (+60%), which could have significant impact on HLW processing. It is still to be shown whether the Re is a solid solution in the magnetite as {sup 99}Tc was determined to be in goethite.

  20. 100 Area soil washing bench-scale test procedures

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Gerber, M.A.; Mattigod, S.V.; Serne, R.J.

    1993-03-01

    This document describes methodologies and procedures for conducting soil washing treatability tests in accordance with the 100 Area Soil Washing Treatability Test Plan (DOE-RL 1992, Draft A). The objective of this treatability study is to evaluate the use of physical separation systems and chemical extraction methods as a means of separating chemically and radioactively contaminated soil fractions from uncontaminated soil fractions. These data will be primarily used for determining feasibility of the individual unit operations and defining the requirements for a system, or systems, for pilot-scale testing.

  1. Effect of nutrient sources on bench scale vinegar production using response surface methodology Efeito das fontes de nutrientes sobre a produção de vinagre em escala de bancada, usando-se a metodologia de superfície de resposta

    Directory of Open Access Journals (Sweden)

    Joelma M. Ferreira

    2005-03-01

    Full Text Available The present work aims to evaluate on a bench scale, the effects of nitrogen and phosphorous nutrient source concentrations in vinegar production, a process that is used by small scale industries in the State of Paraiba. The response surface methodology has been utilized for modeling and optimization of the fermentation process. Initially a 2³ complete factorial design was used, where the effects of initial concentrations of ethyl alcohol, phosphorous and nitrogen sources were observed. After this analysis the concentration range of the nutrient variables were extended and a two level plus a star configuration factorial experimental design was performed. The experimental values are well represented by the linear and quadratic model equations obtained. The optimum concentration of ethanol was 4% in which the yield and the productivity of the acetic acid were maximized to the values of 70% and 0.87 g L-1 h-1 respectively, for a 24 hours fermentation period. The evaluation of the quadratic models showed that the yield of vinegar is maximized from 28.1 to 51.04% and the productivity from 0.69 to 1.29 g L-1 h-1 when the concentration of the nitrogen nutrient in the medium is increased from 0.2 to 2.3 g mL-1. Thus, at the optimized nitrogen nutrient concentration both the yield and the productivity of the vinegar are increased by 1.85 times.Objetivou-se com o presente trabalho, estudar em escala de bancada, os efeitos de concentrações de fontes dos nutrientes nitrogênio e fósforo sobre a produção de vinagre de álcool, um processo muito utilizado nas indústrias de pequeno porte do Estado da Paraíba. A metodologia de superfície de resposta foi usada na modelagem e otimização de processo de fermentação acética. Inicialmente, a metodologia de planejamento fatorial completo 2³ foi utilizada, onde os efeitos das concentrações iniciais de etanol, de fontes de fósforo e de nitrogênio foram observados. Após esta análise as faixas das

  2. The reaction of fish to light (laboratory experiments)

    International Nuclear Information System (INIS)

    De Potter, M.R.

    1993-01-01

    The results of the study on the title subject can contribute to the realization of decreasing the damage to sea trout, caused by cooling water input of thermal power plants and turbines of hydroelectric power plants. Trout can be diverted from the cooling water inlets by means of light screens. Bench-scale experiments were executed to analyze the impact of the rate of the water flow to the reaction of young sea trout (smolts) to light. Also the effectiveness of light bulbs and fluorescence lamps are compared. The smolts show a clear aversion to a small amount of light. For a high water flow and in standing water the aversion reaction to light is considerably smaller or absent

  3. The reaction of fish to light (laboratory experiments)

    International Nuclear Information System (INIS)

    De Potter, M.R.

    1993-01-01

    The results of the study on the title subject can contribute to the realization of decreasing the damage to eel, caused by cooling water input of thermal power plants and turbines of hydroelectric power plants. Eel can be diverted from the cooling water inlets by means of light screens. Bench-scale experiments were executed to analyze the impact of the rate of the water flow to the reaction of eel to light. Also the effectiveness of light bulbs and fluorescence lamps are compared. Eel shows a clear aversion to a small amount of light. The diversion percentage decreases with a higher velocity of the water flow. Application of energy-efficient fluorescent lamps is considered to be a good option for diversion light systems

  4. The superconducting magnet system for the WENDELSTEIN 7-X fusion experiment

    International Nuclear Information System (INIS)

    Sapper, J.

    1995-01-01

    In devices of the TOKAMAK type (JET/Culham, GB, and TFTR/Princeton Laboratory, U.S.A.), successful plasma ignition was achieved, and fusion-induced generation of electricity of some megawatts, for a period of seconds. Experiments of the next generation will tackle the problems of electricity generation sustained over longer periods, for which the STELLARATOR machines are the device of choice, as these, other than the TOKAMAKS, do not require generation of plasma ring currents between 10 and 20 MA. The magnet system in the STELLARATOR devices has to be a superconducting magnet system. At present, bench-scale LT superconductors are available made of materials on the basis of NbTi or Nb 3 Sn, which are applied according to system configuration ( induction at the conductor, current density, temperature, alternating magnetic field load). The paper explains the magnet system intended for use in the planned STELLARATOR WENDELSTEIN 7-X experiments at IPP, Garching. (orig./MM) [de

  5. Sequential UASB and dual media packed-bed reactors for domestic wastewater treatment - experiment and simulation.

    Science.gov (United States)

    Rodríguez-Gómez, Raúl; Renman, Gunno

    2016-01-01

    A wastewater treatment system composed of an upflow anaerobic sludge blanket (UASB) reactor followed by a packed-bed reactor (PBR) filled with Sorbulite(®) and Polonite(®) filter material was tested in a laboratory bench-scale experiment. The system was operated for 50 weeks and achieved very efficient total phosphorus (P) removal (99%), 7-day biochemical oxygen demand removal (99%) and pathogenic bacteria reduction (99%). However, total nitrogen was only moderately reduced in the system (40%). A model focusing on simulation of organic material, solids and size of granules was then implemented and validated for the UASB reactor. Good agreement between the simulated and measured results demonstrated the capacity of the model to predict the behaviour of solids and chemical oxygen demand, which is critical for successful P removal and recovery in the PBR.

  6. Assessment of crown fire initiation and spread models in Mediterranean conifer forests by using data from field and laboratory experiments

    Energy Technology Data Exchange (ETDEWEB)

    Rodríguez y Silva, F.; Guijarro, M.; Madrigal, J.; Jiménez, E.; Molina, J.R.; Hernando, C.; Vélez, R.; Vega, J.A.

    2017-11-01

    Aims of study: To conduct the first full-scale crown fire experiment carried out in a Mediterranean conifer stand in Spain; to use different data sources to assess crown fire initiation and spread models, and to evaluate the role of convection in crown fire initiation. Area of study: The Sierra Morena mountains (Coordinates ETRS89 30N: X: 284793-285038; Y: 4218650-4218766), southern Spain, and the outdoor facilities of the Lourizán Forest Research Centre, northwestern Spain. Material and methods: The full-scale crown fire experiment was conducted in a young Pinus pinea stand. Field data were compared with data predicted using the most used crown fire spread models. A small-scale experiment was developed with Pinus pinaster trees to evaluate the role of convection in crown fire initiation. Mass loss calorimeter tests were conducted with P. pinea needles to estimate residence time of the flame, which was used to validate the crown fire spread model. Main results: The commonly used crown fire models underestimated the crown fire spread rate observed in the full-scale experiment, but the proposed new integrated approach yielded better fits. Without wind-forced convection, tree crowns did not ignite until flames from an intense surface fire contacted tree foliage. Bench-scale tests based on radiation heat flux therefore offer a limited insight to full-scale phenomena. Research highlights: Existing crown fire behaviour models may underestimate the rate of spread of crown fires in many Mediterranean ecosystems. New bench-scale methods based on flame buoyancy and more crown field experiments allowing detailed measurements of fire behaviour are needed.

  7. Heavy metal contaminant remediation study of western Xiamen Bay sediment, China: laboratory bench scale testing results.

    Science.gov (United States)

    Zhang, Luoping; Feng, Huan; Li, Xiaoxia; Ye, Xin; Jing, Youhai; Ouyang, Tong; Yu, Xingtian; Liang, Rongyuan; Chen, Weiqi

    2009-12-15

    A surface sediment sample (metal removal, whereas agitation, aeration and rotation of the samples in chemical complexation solutions yield much better metal removal efficiency (up to 90%). A low pH condition (e.g., pHliquid ratio (e.g., S:L=1:50) could increase metal removal efficiency. The experimental results suggest that 0.20 M (NH4)2C2O4+0.025 M EDTA combination with solid:liquid ratio=1:50 and 0.50 M ammonium acetate (NH4Ac)+0.025 M EDTA combination with solid:liquid ratio=1:50 are the most effective methods for metal removal from the contaminated sediments. This research provides additional useful information for sediment metal remediation technology development.

  8. Comparison of complex effluent treatability in different bench scale microbial electrolysis cells.

    Science.gov (United States)

    Ullery, Mark L; Logan, Bruce E

    2014-10-01

    A range of wastewaters and substrates were examined using mini microbial electrolysis cells (mini MECs) to see if they could be used to predict the performance of larger-scale cube MECs. COD removals and coulombic efficiencies corresponded well between the two reactor designs for individual samples, with 66-92% of COD removed for all samples. Current generation was consistent between the reactor types for acetate (AC) and fermentation effluent (FE) samples, but less consistent with industrial (IW) and domestic wastewaters (DW). Hydrogen was recovered from all samples in cube MECs, but gas composition and volume varied significantly between samples. Evidence for direct conversion of substrate to methane was observed with two of the industrial wastewater samples (IW-1 and IW-3). Overall, mini MECs provided organic treatment data that corresponded well with larger scale reactor results, and therefore it was concluded that they can be a useful platform for screening wastewater sources. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Comparison of complex effluent treatability in different bench scale microbial electrolysis cells

    KAUST Repository

    Ullery, Mark L.

    2014-10-01

    A range of wastewaters and substrates were examined using mini microbial electrolysis cells (mini MECs) to see if they could be used to predict the performance of larger-scale cube MECs. COD removals and coulombic efficiencies corresponded well between the two reactor designs for individual samples, with 66-92% of COD removed for all samples. Current generation was consistent between the reactor types for acetate (AC) and fermentation effluent (FE) samples, but less consistent with industrial (IW) and domestic wastewaters (DW). Hydrogen was recovered from all samples in cube MECs, but gas composition and volume varied significantly between samples. Evidence for direct conversion of substrate to methane was observed with two of the industrial wastewater samples (IW-1 and IW-3). Overall, mini MECs provided organic treatment data that corresponded well with larger scale reactor results, and therefore it was concluded that they can be a useful platform for screening wastewater sources. © 2014 Elsevier Ltd.

  10. Development of a bench-scale fluidized bed combustor (FBC) for ...

    African Journals Online (AJOL)

    The high technological level of equipment for combustion of fuels, as well as the necessity for rational and efficient use of non-renewable energy resources, has resulted demanding requirements that must be fulfilled by equipment for energy production, via combustion. These requirements form the characteristics of ...

  11. Bacterial communities associated with biofouling materials used in bench-scale hydrocarbon bioremediation.

    Science.gov (United States)

    Al-Mailem, Dina; Kansour, Mayada; Radwan, Samir

    2015-03-01

    Biofouling material samples from the Arabian (Persian) Gulf, used as inocula in batch cultures, brought about crude oil and pure-hydrocarbon removal in a mineral medium. Without any added nitrogen fertilizers, the hydrocarbon-removal values were between about 10 and 50 %. Fertilization with NaNO3 alone or together with a mixture of the vitamins thiamine, pyridoxine, vitamin B12, biotin, riboflavin, and folic acid increased the hydrocarbon-removal values, to reach 90 %. Biofouling material samples harbored total bacteria in the magnitude of 10(7) cells g(-1), about 25 % of which were hydrocarbonoclastic. These numbers were enhanced by NaNO3 and vitamin amendment. The culture-independent analysis of the total bacterioflora revealed the predominance of the gammaproteobacterial genera Marinobacter, Acinetobacter, and Alcanivorax, the Flavobacteriia, Flavobacterium, Gaetbulibacter, and Owenweeksia, and the Alphaproteobacteria Tistrella, Zavarzinia, and others. Most of those bacteria are hydrocarbonoclastic. Culture-dependent analysis of hydrocarbonoclastic bacteria revealed that Marinobacter hydrocarbonoclasticus, Dietzia maris, and Gordonia bronchialis predominated in the fouling materials. In addition, each material had several more-specific hydrocarbonoclastic species, whose frequencies were enhanced by NaNO3 and vitamin fertilization. The same samples of fouling materials were used in four successive crude-oil-removal cycles without any dramatic loss of their hydrocarbon-removal potential nor of their associated hydrocarbonoclastic bacteria. In the fifth cycle, the oil-removal value was reduced by about 50 % in only one of the studied samples. This highlights how firmly biofouling materials were immobilizing the hydrocarbonoclastic bacteria.

  12. Full-Scale and Bench-Scale Studies on the Removal of Strontium from Water (abstract)

    Science.gov (United States)

    Strontium (Sr) is a natural and commonly occurring alkaline earth metal which has an oxidation state of +2 under normal environmental conditions. Stable strontium is suspended in water and is dissolved after water runs through rocks and soil. It behaves very similar to calcium. G...

  13. WASTE SOLIDIFICATION BUILDING BENCH SCALE HIGH ACTIVITY WASTE SIMULANT VARIABILITY STUDY FY2008

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, E; Timothy Jones, T; Tommy Edwards, T; Alex Cozzi, A

    2009-03-20

    The primary objective of this task was to perform a variability study of the high activity waste (HAW) acidic feed to determine the impact of feed variability on the quality of the final grout and on the mixability of the salt solution into the dry powders. The HAW acidic feeds were processed through the neutralization/pH process, targeting a final pH of 12. These fluids were then blended with the dry materials to make the final waste forms. A secondary objective was to determine if elemental substitution for cost prohibitive or toxic elements in the simulant affects the mixing response, thus providing a more economical simulant for use in full scale tests. Though not an objective, the HAW simulant used in the full scale tests was also tested and compared to the results from this task. A statistically designed test matrix was developed based on the maximum molarity inputs used to make the acidic solutions. The maximum molarity inputs were: 7.39 HNO{sub 3}, 0.11618 gallium, 0.5423 silver, and 1.1032 'other' metals based on their NO{sub 3}{sup -} contribution. Substitution of the elements aluminum for gallium and copper for silver was also considered in this test matrix, resulting in a total of 40 tests. During the NaOH addition, the neutralization/pH adjustment process was controlled to a maximum temperature of 60 C. The neutralized/pH adjusted simulants were blended with Portland cement and zircon flour at a water to cement mass ratio of 0.30. The mass ratio of zircon flour to Portland cement was 1/12. The grout was made using a Hobart N-50 mixer running at low speed for two minutes to incorporate and properly wet the dry solids with liquid and at medium speed for five minutes for mixing. The resulting fresh grout was measured for three consecutive yield stress measurements. The cured grout was measured for set, bleed, and density. Given the conditions of preparing the grout in this task, all of the grouts were visually well mixed prior to preparing the grouts for measurements. All of the cured grouts were measured for bleed and set. All of the cured grouts satisfied the bleed and set requirements, where no bleed water was observed on any of the grout samples after one day and all had set within 3 days of curing. This data indicates, for a well mixed product, bleed and set requirement are satisfied for the range of acidic feeds tested in this task. The yield stress measurements provide both an indication on the mixability of the salt solution with dry materials and an indication of how quickly the grout is starting to form structure. The inability to properly mix these two streams into a well mixed grout product will lead to a non-homogeneous mixture that will impact product quality. Product quality issues could be unmixed regions of dry material and hot spots having high concentrations of americium 241. Mixes that were more difficult to incorporate typically resulted in grouts with higher yield stresses. The mixability from these tests will provide Waste Solidification Building (WSB) an indication of which grouts will be more challenging to mix. The first yield stress measurements were statistically compared to a list of variables, specifically the batched chemicals used to make the acidic solutions. The first yield stress was also compared to the physical properties of the acidic solutions, physical and pH properties of the neutralized/pH adjusted solutions, and chemical and physical properties of the grout.

  14. Copper recovery in a bench-scale carrier facilitated tubular supported liquid membrane system

    Directory of Open Access Journals (Sweden)

    Makaka S.

    2010-01-01

    Full Text Available The extraction of copper ions in a tubular supported liquid membrane using LIX 984NC as a mobile carrier was studied, evaluating the effect of the feed characteristics (flowrate, density, viscosity on the feedside laminar layer of the membrane. A vertical countercurrent, double pipe perspex benchscale reactor consisting of a single hydrophobic PVDF tubular membrane mounted inside was used in all test work. The membrane was impregnated with LIX 984NC and became the support for this organic transport medium. Dilute Copper solution passed through the centre pipe and sulphuric acid as strippant passed through the shell side. Copper was successfully transported from the feedside to the stripside and from the data obtained, a relationship between Schmidt, Reynolds and Sherwood number was achieved of.

  15. DESIGN AND EVALUATION OF BENCH-SCALE COMPOST TREATMENT SYSTEM FOR HAZARDOUS WASTE

    Science.gov (United States)

    Soil bound contamination presents a significant set of problems to those attempting to remediate the soil. Bioremediation has received considerable attention, as a potential answer to the obvious remediation needs. Composting technology represents a promising means to use indigen...

  16. Evaluation of effluents from bench-scale treatment combinations for landfill leachate in Ibadan, Nigeria.

    Science.gov (United States)

    Aluko, Olufemi Oludare; Sridhar, Mkc

    2014-01-01

    The removal of pollutants in landfill leachate was investigated using constructed wetlands, a trickling filter, alum flocculation and coagulation, and a sequencing batch reactor in various combinations. Thirteen combined operations were investigated involving three out of the four unit treatment methods in series. The study was conducted because unit operations, though achieved reductions in pollutants concentrations had effluent values above the national regulatory guideline values. The suspended solids of effluents were permissible in most treatment processes, while reductions in 5-day biochemical oxygen demand (BOD5), chemical oxygen demand (COD) and ammonia (NH3) of leachates ranged from 80% to 97%; 86% to 97% and 92% to 98% respectively. However, there were significant increases in nitrate (85%) and dissolved oxygen of treatment (218%). In addition, the characteristics of the recommended treatment sequence, involving constructed wetlands, alum and trickling filter produced effluents with reductions in colour (97%), alkalinity (97%), BOD (97%), COD (97%) and NH3 (98%), and in metals, except nickel (29% reduction from the influent values). The recommended treatment combination is suitable for effective leachate management at the landfill. The cost of constructing and operating the recommended treatment combination at the facility, for 5 years, would be NGN6,009,750.00 ($38,036.39). The performance should be monitored on site prior to full adoption if effluent characteristics remain consistently low over dry and wet seasons.

  17. Bench Scale Development and Testing of a Novel Adsorption Process for Post-Combustion CO₂ Capture

    Energy Technology Data Exchange (ETDEWEB)

    Jain, Ravi [Innosepra Limited Liability Company, Middlesex, NJ (United States)

    2015-09-01

    A physical sorption process to produce dry CO₂ at high purity (>98%) and high recovery (>90%) from the flue gas taken before or after the FGD was demonstrated both in the lab and in the field (one ton per day scale). A CO₂ recovery of over 94% and a CO₂ purity of over 99% were obtained in the field tests. The process has a moisture, SOX, and Hg removal stage followed by a CO₂ adsorption stage. Evaluations based on field testing, process simulation and detailed engineering studies indicate that the process has the potential for more than 40% reduction in the capital and more than 40% reduction in parasitic power for CO₂ capture compared to MEA. The process has the potential to provide CO₂ at a cost (<$40/tonne) and quality (<1 ppm H₂O, <1 ppm SOX, <10 ppm O₂) suitable for EOR applications which can make CO₂ capture profitable even in the absence of climate legislation. The process is applicable to power plants without SOX, Hg and NOX removal equipment.

  18. Treatability study for the bench-scale solidification of nonincinerable LDR low-level mixed waste

    International Nuclear Information System (INIS)

    Gering, K.L.

    1993-01-01

    The focus of this report is the solidification of nonincinerable, land disposal restricted (LDR) low-level mixed waste generated at the Idaho National Engineering Laboratory. Benchscale solidification was performed on samples of this mixed waste, which was done under a Resource Conservation and Recovery Act treatability study. Waste forms included liquids, sludges, and solids, and treatment techniques included the use of conventional Portland cement and sulphur polymer cement (SPC). A total of 113 monoliths were made under the experimental design matrix for this study; 8 of these were ''blank'' monoliths (contained no waste). Thus, 105 monoliths were used to solidify 21.6 kg of mixed waste; 92 were made with Portland cement systems, and 13 were made with SPC. Recipes for all monoliths are given, and suggested recipes (as based on the minimized leaching of toxic components) are summarized. In most cases, the results presented herein indicate that solidification was successful in immobilizing toxic metals, thereby transforming low-level mixed waste into low-level nonhazardous waste. The ultimate goal of this project is to use appropriate solidification techniques, as described in the literature, to transform low-level mixed waste to low-level nonhazardous waste by satisfying pertinent disposal requirements for this waste. Disposal requirements consider the toxicity characteristic leaching procedure tests, a free liquids test, and radiological analyses. This work is meaningful in that it will provide a basis for the disposal of waste that is currently categorized as LDR low-level mixed waste

  19. BENCH-SCALE STUDIES TO IDENTIFY PROCESS PARAMETERS CONTROLLING REBURNING WITH PULVERIZED COAL

    Science.gov (United States)

    The report addresses the evaluation of a technology which is a combination of two technologies used to control the atmospheric emission of NOx by stationary sources: (1) combustion modification (controls flame temperature and maximizes fuel-rich residence time to minimize NOx for...

  20. Bench-scale composting of source-separated human faeces for sanitation.

    Science.gov (United States)

    Niwagaba, C; Nalubega, M; Vinnerås, B; Sundberg, C; Jönsson, H

    2009-02-01

    In urine-diverting toilets, urine and faeces are collected separately so that nutrient content can be recycled unmixed. Faeces should be sanitized before use in agriculture fields due to the presence of possible enteric pathogens. Composting of human faeces with food waste was evaluated as a possible method for this treatment. Temperatures were monitored in three 78-L wooden compost reactors fed with faeces-to-food waste substrates (F:FW) in wet weight ratios of 1:0, 3:1 and 1:1, which were observed for approximately 20 days. To achieve temperatures higher than 15 degrees C above ambient, insulation was required for the reactors. Use of 25-mm thick styrofoam insulation around the entire exterior of the compost reactors and turning of the compost twice a week resulted in sanitizing temperatures (>or=50 degrees C) to be maintained for 8 days in the F:FW=1:1 compost and for 4 days in the F:FW=3:1 compost. In these composts, a reduction of >3 log(10) for E. coli and >4 log(10) for Enterococcus spp. was achieved. The F:FW=1:0 compost, which did not maintain >or=50 degrees C for a sufficiently long period, was not sanitized, as the counts of E. coli and Enterococcus spp. increased between days 11 and 15. This research provides useful information on the design and operation of family-size compost units for the treatment of source-separated faeces and starchy food residues, most likely available amongst the less affluent rural/urban society in Uganda.

  1. Recommendations for Filler Material Composition and Delivery Method for Bench-Scale Testing

    Energy Technology Data Exchange (ETDEWEB)

    Hardin, Ernest [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brady, Patrick Vane [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2018-03-01

    This report supplements Joint Workplan on Filler Investigations for DPCs (SNL 2017) providing new and some corrected information for use in planning Phase 1 laboratory testing of slurry cements as possible DPC fillers. The scope description is to "Describe a complete laboratory testing program for filler composition, delivery, emplacement in surrogate canisters, and post-test examination. To the extent possible specify filler material and equipment sources." This report includes results from an independent expert review (Dr. Arun Wagh, retired from Argonne National Laboratory and contracted by Sandia) that helped to narrow the range of cement types for consideration, and to provide further guidance on mix variations to optimize injectability, durability, and other aspects of filler performance.

  2. EFRT M-12 Issue Resolution: Comparison of PEP and Bench-Scale Oxidative Leaching Results

    Energy Technology Data Exchange (ETDEWEB)

    Rapko, Brian M.; Schonewill, Philip P.; Brown, Christopher F.; Eslinger, Paul W.; Fountain, Matthew S.; Hausmann, Tom S.; Huckaby, James L.; Hanson, Brady D.; Kurath, Dean E.; Minette, Michael J.

    2010-01-01

    Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes” of the External Flowsheet Review Team (EFRT) issue response plan.( ) The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing.

  3. Removal of enteroviruses from sewage by bench-scale rotary-tube trickling filters.

    Science.gov (United States)

    Clarke, N A; Chang, S L

    1975-08-01

    The efficacy of a rotary-tube type of trickling filter for removing coxsackievirus A9, poliovirus 1, and echovirus 12 suspended in raw settled sewage was investigated. At filtration rates equivalent to about 10 MGD (million gallons per day)/acre (ca. 3,785 m3/day per acre), the filters removed 95% of the poliovirus, 83% of echovirus 12, and 94% of coxsackievirus A9. Coliform, fecal streptococci, biochemical oxygen demand, and chemical oxygen demand removals were remarkably similar, averaging 94, 92, 93, and 95%, respectively. At filtration rates equivalent to about 23 MGD/acre, 59% of the poliovirus, 63% of the echovirus 23, and 81% of the coxsackievirus A9 were removed. Coliform, fecal streptococci, biochemical oxygen demand, and chemical oxygen demand removals at this filtration rate were 68, 75, 72, and 56%, respectively. Viruses were assumed to be adsorbed to the biological slime growing in the filters, but attempts to disassociate the viruses from the slime were unsuccessful, indicating that the slime-virus complex is very stable or that the viruses were somehow inactivated. The data indicate that coliform and fecal streptococci reductions in this type sewage treatment process can be used as an index of virus reduction. Disinfection, however, must be used to ensure a virus-free final effluent.

  4. Bench Scale Treatability Studies of Contaminated Soil Using Soil Washing Technique

    OpenAIRE

    Gupta, M. K.; Srivastava, R. K.; Singh, A. K.

    2010-01-01

    Soil contamination is one of the most widespread and serious environmental problems confronting both the industrialized as well as developing nations like India. Different contaminants have different physicochemical properties, which influence the geochemical reactions induced in the soils and may bring about changes in their engineering and environmental behaviour. Several technologies exist for the remediation of contaminated soil and water. In the present study soil washing technique using...

  5. Heat and Mass Transfer in a Reforming Catalyst Bed: Quantitative Evaluation of the Controlling Factor by Experiment

    Science.gov (United States)

    Usami, Yutaka; Fukusako, Shoichiro; Yamada, Masahiko

    Heat and mass transfer characteristics in a reforming catalyst bed have been experimentally investigated. Experiments were carried out with a single bench-scaled reforming tube which was filled with reforming catalyst. The tube wall was uniformly heated, and mixtures of steam and methane or propane were reformed through the catalyst bed. Most part of the reaction was completed in the upper part of the test tube. The effects of space velocity, which is a ratio of volumetric flow rate of process gas to the catalyst volume, steam carbon molar ratio, wall temperature, bed temperature, and catalyst particle diameter on the transport phenomena with chemical reaction, were determined. A correlation to heat transfer coefficient was determined by Nu, Rep, Pr, dp/d, and Da. The prediction of the overall methane conversion rate was also presented.

  6. Transverse dispersion: From laboratory experiments to field applications

    Science.gov (United States)

    Grathwohl, Peter; Rügner, Hermann

    2016-04-01

    Transverse dispersion is relevant for dilution of contaminant plumes in groundwater and in many cases controls the length of steady state plumes during natural attenuation. Also dissolution kinetics of NAPLs in porous media and mass transfer of vapor phase compounds across the capillary fringe (e.g. supply of oxygen) is limited by transverse dispersion. In bench scale laboratory experiments typically very small dispersion coefficients are observed. Transverse dispersivities determined in DNAPL pool dissolution experiments in coarse sands are less than 0.1 mm which agrees with results from lab experiments on dilution of tracers and transfer of oxygen across the capillary fringe. Such low dispersivities lead to long-term persistence of DNAPL pools of many decades to centuries which is confirmed e.g. for chlorinated solvents and coal tars by observations at contaminated sites. However, larger scale investigations, e.g. determination of the length of steady state plumes or reduction of mass fluxes of biodegradable compounds suggest that transverse dispersivities at field scale are up to 3 orders of magnitude higher (1 -10 cm). Reasons for this discrepancy are still unclear, but may be partly explained by processes enhancing transverse mixing such as flow focusing due to aquifer geometries or high permeability inclusions and helical groundwater flow induced by herringbone structures in sediments.

  7. Science Support for Space-Based Droplet Combustion: Drop Tower Experiments and Detailed Numerical Modeling

    Science.gov (United States)

    Marchese, Anthony J.; Dryer, Frederick L.

    1997-01-01

    This program supports the engineering design, data analysis, and data interpretation requirements for the study of initially single component, spherically symmetric, isolated droplet combustion studies. Experimental emphasis is on the study of simple alcohols (methanol, ethanol) and alkanes (n-heptane, n-decane) as fuels with time dependent measurements of drop size, flame-stand-off, liquid-phase composition, and finally, extinction. Experiments have included bench-scale studies at Princeton, studies in the 2.2 and 5.18 drop towers at NASA-LeRC, and both the Fiber Supported Droplet Combustion (FSDC-1, FSDC-2) and the free Droplet Combustion Experiment (DCE) studies aboard the shuttle. Test matrix and data interpretation are performed through spherically-symmetric, time-dependent numerical computations which embody detailed sub-models for physical and chemical processes. The computed burning rate, flame stand-off, and extinction diameter are compared with the respective measurements for each individual experiment. In particular, the data from FSDC-1 and subsequent space-based experiments provide the opportunity to compare all three types of data simultaneously with the computed parameters. Recent numerical efforts are extending the computational tools to consider time dependent, axisymmetric 2-dimensional reactive flow situations.

  8. Gasification experience with biomass and wastes

    Energy Technology Data Exchange (ETDEWEB)

    Schiffer, H.P.; Adlhoch, W. [Rheinbraun AG, Cologne (Germany)

    1996-12-31

    The HTW process is particularly favourable for the gasification of low-rank feedstocks. During various tests - performed in b-bench- scale, pilot-scale and industrial scale units - consequences with regard to feedstock preparation. Gasification behaviour, corrosion, emission and residual matter were carefully studied for a large number of different feedstocks. Information is now available for optimal utilisation of several types of biomass and waste materials in relation to plant operation, emission and residue utilization. Different types of biomass were tested in bench-scale conditions in an atmospheric HTW process development unit. Industrial-scale experience concerning biomass is available from the Gasification plant at Oulu, Finland, which operated from 1988 to 1991, producing ammonia synthesis gas from dried Finnish peat. During several test campaigns performed at the HTW demonstration plant sewage sludge, loaded coke and used plastics were co-gasified at feeding rates of up to 5 t/h. Operability, conversion efficiency, syngas contaminants, solid residue characteristics and emissions were monitored very carefully. Co-gasification in a dried lignite mixture allows synthesis gas for methanol production to be obtained also from waste materials. Thus, waste is converted into a useful chemical feedstock. For both sewage sludge and loaded coke, conversion efficiency and syngas yield were sufficient. Within the scope of a solid residue characterization various contaminants, including chlorine, sulphur, heavy metals and other trace elements or organic compounds, their formation and/or release were detected. Emissions were well below the limits. However, an increase in the benzene and naphthalene concentrations in the crude gas occurred. Thus, a commercial application requires additional gas treatment. In the next few years, feedstock recycling of mixed plastics household waste from Duales System Deutschland GmbH will call for a plant capacity of 350 000 to 400 000

  9. Uranium Release from Acidic Weathered Hanford Sediments: Single-Pass Flow-Through and Column Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Guohui [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Um, Wooyong [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Pohang University of Science and Technology (POSTECH), Pohang, South Korea; Wang, Zheming [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Reinoso-Maset, Estela [Sierra; Washton, Nancy M. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Mueller, Karl T. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Perdrial, Nicolas [Department; Department; O’Day, Peggy A. [Sierra; Chorover, Jon [Department

    2017-09-21

    The reaction of acidic radioactive waste with sediments can induce mineral transformation reactions that, in turn, control contaminant fate. Here, sediment weathering by synthetic uranium-containing acid solutions was investigated using bench-scale experiments to simulate waste disposal conditions at Hanford’s cribs, USA. During acid weathering, the presence of phosphate exerted a strong influence over uranium mineralogy and a rapidly precipitated, crystalline uranium phosphate phase (meta-ankoleite [K(UO2)(PO4)·3H2O]) was identified using spectroscopic and diffraction-based techniques. In phosphate-free system, uranium oxyhydroxide minerals such as K-compreignacite [K2(UO2)6O4(OH)6·7H2O] were formed. Single-pass flow-through (SPFT) and column leaching experiments using synthetic Hanford pore water showed that uranium precipitated as meta-ankoleite during acid weathering was strongly retained in the sediments, with an average release rate of 2.67E-12 mol g-1 s-1. In the absence of phosphate, uranium release was controlled by dissolution of uranium oxyhydroxide (compreignacite-type) mineral with a release rate of 1.05-2.42E-10 mol g-1 s-1. The uranium mineralogy and release rates determined for both systems in this study support the development of accurate U-release models for prediction of contaminant transport. These results suggest that phosphate minerals may be a good candidate for uranium remediation approaches at contaminated sites.

  10. Indoor Secondary Pollutants from Household Product Emissions inthe Presence of Ozone: A Bench-Scale Chamber Study

    Energy Technology Data Exchange (ETDEWEB)

    Destaillats, Hugo; Lunden, Melissa M.; Singer, Brett C.; Coleman,Beverly K.; Hodgson, Alfred T.; Weschler, Charles J.; Nazaroff, William W.

    2005-10-01

    Ozone-driven chemistry is a major source of indoor secondary pollutants of health concern. This study investigates secondary air pollutants formed from reactions between constituents of household products and ozone. Gas-phase product emissions were introduced along with ozone at constant rates into a 198-L Teflon-lined reaction chamber. Gas-phase concentrations of reactive terpenoids and oxidation products were measured. Formaldehyde was a predominant oxidation byproduct for the three studied products, with yields under most conditions of 20-30% with respect to ozone consumed. Acetaldehyde, acetone, glycolaldehyde, formic acid and acetic acid were each also detected for two or three of the products. Immediately upon mixing of reactants, a scanning mobility particle sizer detected particle nucleation events that were followed by a significant degree of ultrafine particle growth. The production of secondary gaseous pollutants and particles depended primarily on the ozone level and was influenced by other parameters such as the air-exchange rate. Hydroxyl radical concentrations in the range 0.04-200 x 10{sup 5} molecules cm{sup -3} were measured. OH concentrations were observed to vary strongly with residual ozone level in the chamber, which was in the range 1-25 ppb, as is consistent with expectations from a simplified kinetic model. In a separate test, we exposed the dry residue of two products to ozone in the chamber and observed the formation of gas-phase and particle-phase secondary oxidation products.

  11. Bench-Scale Investigation of Composting for Remediation of Explosives-Contaminated Soils from Naval Surface Warfare Center, Crane, Indiana

    National Research Council Canada - National Science Library

    Preston, Kurt

    1998-01-01

    ...), and octahydro-1,3,5,7-tetranitro-1,3,5,7- tetrazocine (HMX). The Naval Surface Warfare Center (NSWC), Crane, Indiana, provides material and logistic support to the Navy's weapon systems, including expendable and nonexpendable ordnance items...

  12. An optimisation approach for culturing shear-sensitive dinoflagellate microalgae in bench-scale bubble column photobioreactors.

    Science.gov (United States)

    López-Rosales, L; García-Camacho, F; Sánchez-Mirón, A; Contreras-Gómez, A; Molina-Grima, E

    2015-12-01

    The dinoflagellate Karlodinium veneficum was grown in bubble column photobioreactors and a genetic algorithm-based stochastic search strategy used to find optimal values for the culture parameters gas flow rate, culture height, and nozzle sparger diameter. Cell production, concentration of reactive oxygen species (ROS), membrane fluidity and photosynthetic efficiency were studied throughout the culture period. Gas-flow rates below 0.26Lmin(-1), culture heights over 1.25m and a nozzle diameter of 1.5mm were found to provide the optimal conditions for cell growth, with an increase of 60% in cell production with respect to the control culture. Non-optimal conditions produced a sufficiently high shear stress to negatively affect cell growth and even produce cell death. Cell physiology was also severely affected in stressed cultures. The production of ROS increased by up to 200%, whereas cell membrane fluidity decreased by 60% relative to control cultures. Photosynthetic efficiency decreased concomitantly with membrane fluidity. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Removal of Strontium from Drinking Water by Conventional Treatment and Lime Softening in Bench-Scale Studies

    Science.gov (United States)

    The United States Environmental Protection Agency Contaminant Candidate List 3 lists strontium as a contaminant for potential regulatory consideration in drinking water. There is very little data available on strontium removal from drinking water. As a result, there is an immedia...

  14. Removal of uranium from uranium-contaminated soils -- Phase 1: Bench-scale testing. Uranium in Soils Integrated Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Francis, C. W.

    1993-09-01

    To address the management of uranium-contaminated soils at Fernald and other DOE sites, the DOE Office of Technology Development formed the Uranium in Soils Integrated Demonstration (USID) program. The USID has five major tasks. These include the development and demonstration of technologies that are able to (1) characterize the uranium in soil, (2) decontaminate or remove uranium from the soil, (3) treat the soil and dispose of any waste, (4) establish performance assessments, and (5) meet necessary state and federal regulations. This report deals with soil decontamination or removal of uranium from contaminated soils. The report was compiled by the USID task group that addresses soil decontamination; includes data from projects under the management of four DOE facilities [Argonne National Laboratory (ANL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), and the Savannah River Plant (SRP)]; and consists of four separate reports written by staff at these facilities. The fundamental goal of the soil decontamination task group has been the selective extraction/leaching or removal of uranium from soil faster, cheaper, and safer than current conventional technologies. The objective is to selectively remove uranium from soil without seriously degrading the soil`s physicochemical characteristics or generating waste forms that are difficult to manage and/or dispose of. Emphasis in research was placed more strongly on chemical extraction techniques than physical extraction techniques.

  15. Two-stage alkaline hydrothermal liquefaction of wood to biocrude in a continuous bench-scale system

    DEFF Research Database (Denmark)

    Sintamarean, Iulia-Maria; Grigoras, Ionela; Jensen, Claus Uhrenholt

    2017-01-01

    Feedstock pumpability is one of the main obstacles for continuous processing of biomass through hydrothermal liquefaction (HTL), due to their tendency to form heterogeneous slurries. In this work, a novel strategy is proposed to ensure lignocellulosic feed pumpability in HTL processing, even while...

  16. Waste acid detoxification and reclamation: Summary of bench-scale tests for FY 1986 and FY 1987

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, T.L.

    1987-09-01

    Processes to reduce the volume, quantity, and toxicity of metal-bearing waste acid are being demonstrated at Pacific Northwest Laboratory. Two precipitation processes and a distillation process are being developed to minimize waste from fuel fabrication operations, which comprise a series of metal-finishing operations. Waste process acids such as HF-HNO/sub 3/, etch solutions containing Zr as a major metal impurity, and HNO/sub 3/ strip solution containing Cu as a major metal impurity are detoxified and reclaimed by concurrently precipitating heavy metals and regenerating acid for recycle. Acid from a third waste acid stream generated from chemical milling operations will be reclaimed using distillation. This stream comprises HNO/sub 3/ and H/sub 2/SO/sub 4/ containing U as the major metal impurity. Distillation allows NO/sub 3//sup -/ to be displaced by SO/sub 4//sup -2/ in metal salts; free HNO/sub 3/ is then vaporized from the U-bearing sulfate stream. Uranium can be recovered from the sulfate stream in a downstream precipitation step. 10 refs., 15 figs., 13 tabs.

  17. Effects of turbulence modelling on prediction of flow characteristics in a bench-scale anaerobic gas-lift digester

    OpenAIRE

    Coughtrie, AR; Borman, DJ; Sleigh, PA

    2013-01-01

    Flow in a gas-lift digester with a central draft-tube was investigated using computational fluid dynamics (CFD) and different turbulence closure models. The k-ω Shear-Stress-Transport (SST), Renormalization-Group (RNG) k-∊, Linear Reynolds-Stress-Model (RSM) and Transition-SST models were tested for a gas-lift loop reactor under Newtonian flow conditions validated against published experimental work. The results identify that flow predictions within the reactor (where flow is transitional) ar...

  18. Effects of turbulence modelling on prediction of flow characteristics in a bench-scale anaerobic gas-lift digester.

    Science.gov (United States)

    Coughtrie, A R; Borman, D J; Sleigh, P A

    2013-06-01

    Flow in a gas-lift digester with a central draft-tube was investigated using computational fluid dynamics (CFD) and different turbulence closure models. The k-ω Shear-Stress-Transport (SST), Renormalization-Group (RNG) k-∊, Linear Reynolds-Stress-Model (RSM) and Transition-SST models were tested for a gas-lift loop reactor under Newtonian flow conditions validated against published experimental work. The results identify that flow predictions within the reactor (where flow is transitional) are particularly sensitive to the turbulence model implemented; the Transition-SST model was found to be the most robust for capturing mixing behaviour and predicting separation reliably. Therefore, Transition-SST is recommended over k-∊ models for use in comparable mixing problems. A comparison of results obtained using multiphase Euler-Lagrange and singlephase approaches are presented. The results support the validity of the singlephase modelling assumptions in obtaining reliable predictions of the reactor flow. Solver independence of results was verified by comparing two independent finite-volume solvers (Fluent-13.0sp2 and OpenFOAM-2.0.1). Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Intermediate pyrolysis of agro-industrial biomasses in bench-scale pyrolyser: Product yields and its characterization.

    Science.gov (United States)

    Tinwala, Farha; Mohanty, Pravakar; Parmar, Snehal; Patel, Anant; Pant, Kamal K

    2015-01-01

    Pyrolysis of woody biomass, agro-residues and seed was carried out at 500 ± 10 °C in a fixed bed pyrolyser. Bio-oil yield was found varying from 20.5% to 47.5%, whereas the biochar and pyrolysis gas ranged from 27.5% to 40% and 24.5% to 40.5%, respectively. Pyrolysis gas was measured for flame temperature along with CO, CO2, H2, CH4 and other gases composition. HHV of biochar (29.4 MJ/kg) and pyrolitic gas (8.6 MJ/kg) of woody biomass was higher analogous to sub-bituminous coal and steam gasification based producer gas respectively, whereas HHV of bio-oil obtained from seed (25.6 MJ/kg) was significantly more than husks, shells and straws. TGA-DTG studies showed the husks as potential source for the pyrolysis. Bio-oils as a major by-product of intermediate pyrolysis have several applications like substitute of furnace oil, extraction of fine chemicals, whereas biochar as a soil amendment for enhancing soil fertility and gases for thermal application. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Bench-Scale Development of a Hybrid Membrane-Absorption CO{sub 2} Capture Process: Preliminary Cost Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, Brice; Kniep, Jay; Pingjiao, Hao; Baker, Richard; Rochelle, Gary; Chen, Eric; Frailie, Peter; Ding, Junyuan; Zhang, Yue

    2014-03-31

    This report describes a study of capture costs for a hybrid membrane-absorption capture system based on Membrane Technology and Research, Inc. (MTR)’s low-pressure membrane contactors and the University of Texas at Austin’s 5 m piperazine (PZ) Advanced Flash Stripper (AFS; 5 m PZ AFS) based CO2 capture system. The report is submitted for NETL review, and may be superseded by a final topical report on this topic that will be submitted to satisfy the Task 2 report requirement of the current project (DE-FE0013118).

  1. Evaluation of adipic acid addition to a bench-scale Chiyoda Thoroughbred 121 FGD system. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Behrens, G.P.

    1981-12-01

    An experimental laboratory study testing the effectiveness of adipic acid in the Chiyoda Thoroughbred 121 FGD system has been sponsored by the Electric Power Research Institute. Additionally, economic calculations for the cost effectiveness of usng adipic acid in a commercial scale CT-121 FGD system have been performed. The results of this study indicate that although adipic acid can increase the SO/sub 2/ removal capability of the CT-121 system, it is not an economically attractive process improvement. This result is due to the CT-121 process chemistry which minimizes limestone consumption and sludge volume without the need of adipic acid. These two areas realize major cost savings when adipic is used in a conventional limestone FGD system. The economic evaluation indicates even though a lower gas-side pressue drop is achieved when adipic acid is used, the savings in electrical costs are insufficient to offset the cost of adipic acid.

  2. The stability of aerobic granular sludge treating municipal sludge deep dewatering filtrate in a bench scale sequencing batch reactor.

    Science.gov (United States)

    Long, Bei; Yang, Chang-Zhu; Pu, Wen-Hong; Yang, Jia-Kuan; Shi, Ya-Fei; Wang, Jing; Bai, Jun; Zhou, Xuan-Yue; Jiang, Guo-Sheng; Li, Chun-Yang; Liu, Fu-Biao

    2014-10-01

    Inoculated with mature aerobic granular sludge in a sequencing batch reactor, gradually increasing the proportion of municipal sludge deep dewatering filtrate in influent, aerobic granular sludge was domesticated after 84 days and maintained its structure during the operation. The domesticated AGS was yellowish-brown, dense and irregular spherical shape, average size was 1.49 mm, water content and specific density were 98.13% and 1.0114, the SVI and settling velocity were 40 ml/g and 46.5m/h. After 38 days, NO3(-)-N accumulated obviously in the reactor as lack of carbon sources. When adding 1-3g solid CH3COONa at 4.5 and 5.5h of each cycle from the 57th day, the removal rate of TN rose to above 90% after 20 days, where effective COD removal and denitrification were realized in a single bioreactor. Finally, the removal rates of COD, TP, TN and NH4(+)-N were higher than 95%, 88%, 96% and 99%. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Nitrate to ammonia and ceramic (NAC) bench scale stabilization studies. Final technical progress report, May 1995--May 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    The Department of Energy (DOE) has large quantities of sodium-nitrate based liquid wastes. Around 1 billion liters of high level waste tank supernatant are present at Hanford, Savannah River Plant, Rocky Flats Plant, Idaho National Engineering Laboratory, and Oak Ridge National Laboratory. The largest quantity of these wastes is in the 149 single shell tanks at Hanford which hold up to 1 million gallons each. These tank waste are typically 4 to 5 molar in nitrate and contain radionuclides, various salts, and heavy metals. INEL high-level waste tank supernatant contains about 0.7 and 0.6 grams per liter of chromium and mercury, respectively. SRP high-level waste tank supernatant contains about 0.2 g/L of chromium. Other heavy metals could well be present at lower levels in theses tank wastes. The major components present in these wastes are summarized in Appendix A. These wastes are currently regulated and managed by the DOE. Under the Federal Facility Compliance Act (FFCA) DOE is subject to RCRA, which would apply to these tank supernatants. Stabilization of this waste is difficult because nitrates are very mobile. Additionally, vitrification of these wastes produces large quantities of hard-to-manage NO{sub x} emissions. The conversion of sodium nitrate to ammonia is discussed.

  4. Scaling up for the industrial production of rifamycin B; optimization of the process conditions in bench-scale fermentor

    Directory of Open Access Journals (Sweden)

    Hewaida F. El-Sedawy

    2013-06-01

    Full Text Available Optimization of fermentation process conditions using a gene amplified variant of Amycolatopsis mediterranei (NCH was carried out. The use of aeration level 1.5 vvm increased the yield by 16.6% (from 13.81 to 16.1 g/l upon controlling the temperature at 28 °C. Adjustment of the aeration level at 1.5 vvm for 3 days then controlling the dissolved oxygen (DO at 30% saturation further increased the yield to 17.8 g/l. The optimum pH was 6.5 for 3 days then 7 thereafter when a production yield of 16.1 g/l was recorded using an aeration rate of 1.5 vvm. Controlling the pH at constant value (6.5 or 7 all through the fermentation process decreased the yield by 5–21%. Controlling the temperature at 30 °C for 3 days then 28 °C thereafter slightly increased the yield by 5% upon using an aeration rate of 1 vvm while it decreased upon using an aeration rate of 1.5 vvm. Integration of the most optimum conditions increased the production yield by 22% from 13.81 to 17.8 g/l.

  5. Bench-scale testing of the micronized magnetite process. Eighth quarterly technical progress report, April--June, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-13

    The major focus of the project is to install and test a 500 lbs./hr. fine-coal cleaning circuit at DOE`s Process Research Facility (PRF), located at the Pittsburgh Energy Technology Center (PETC). The circuit will utilize an extremely fine, micron-sized magnetite media and small diameter cyclones to make efficient density separations on minus-28-Mesh coal. The circuit consists of three subcircuits: Classification Circuit; Dense-Medium Cycloning Circuit; and Magnetite Recovery Circuit. The testing scope involves initial closed-loop testing of each subcircuit to optimize the performance of the equipment in each subcircuit (i.e., Component Testing), followed by open-circuit testing of the entire integrated circuit to optimize the process and quantify the process efficiency (i.e., Integrated Testing). This report contains a short discussion of the project description, objectives, budget, schedule, and teaming arrangement. It also includes a detailed discussion of the above mentioned project accomplishments and plans, organized by the various task series within the project work plan. The final section contains an outline of the specific project goals for the next quarterly reporting period.

  6. A bench-scale study on the removal and recovery of phosphate by hydrous zirconia-coated magnetite nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhe; Fang, Wenkan; Xing, Mingchao; Wu, Deyi, E-mail: dywu@sjtu.edu.cn

    2017-02-15

    Owing to the easy magnetic separation from water for reuse, magnetic nanoparticles have drawn great interest as adsorbents. Herein hydrous zirconia-coated magnetite nanoparticles (Fe{sub 3}O{sub 4}@ZrO{sub 2}) were created by a facile method and a bench–scale study was undertaken to evaluate its effectiveness and mechanism to remove phosphate at low concentrations. Results indicated that phosphate removal by Fe{sub 3}O{sub 4}@ZrO{sub 2} was fast (95% of phosphate removal within 10 min) and nearly complete removal could be achieved at the adsorbent dosage >0.6 g/L. In tap water or wastewater where competitive anions coexist, regulation of pH was found to be quite effective to augment the performance of phosphate removal. In pH–lowered adsorption systems, phosphate removal followed a good pattern similarly to pure water, i.e., a continuous high efficiency removal followed by a rapid saturation. Adsorption–desorption–regeneration studies showed that Fe{sub 3}O{sub 4}@ZrO{sub 2} could be repeatedly used for phosphate removal and adsorbed phosphate could be stripped for recovery. The fractionation of adsorbed phosphorus suggested that NaOH-P fraction was dominant. We also found that the adsorption reaction of phosphate with Fe{sub 3}O{sub 4}@ZrO{sub 2} shifted the isoelectric point of Fe{sub 3}O{sub 4}@ZrO{sub 2} from ~9.0 to ~3.0. FTIR measurements further showed the direct coordination of phosphate onto zirconium by replacement of hydroxyl groups. The formation of the monodentate (ZrO)PO{sub 2}(OH) complex was proposed. - Highlights: • Hydrous zirconia–coated magnetite was used for phosphate capture. • Regulation of pH was able to enhance P removal in the presence of coexisting ions. • Phosphate was coordinated onto zirconium by replacement of hydroxyl groups. • The material could be easily separated from water for reuse by a magnet. • Desorption of phosphate from the material could be achieved with NaOH treatment.

  7. CFD modeling of space-time evolution of fast pyrolysis products in a bench-scale fluidized-bed reactor

    International Nuclear Information System (INIS)

    Boateng, A.A.; Mtui, P.L.

    2012-01-01

    A model for the evolution of pyrolysis products in a fluidized bed has been developed. In this study the unsteady constitutive transport equations for inert gas flow and decomposition kinetics were modeled using the commercial computational fluid dynamics (CFD) software FLUENT-12. The Eulerarian-Eulerian multiphase model system described herein is a fluidized bed of sand externally heated to a predetermined temperature prior to introduction of agricultural biomass. We predict the spontaneous emergence of pyrolysis vapors, char and non-condensable (permanent) gases and confirm the observation that the kinetics are fast and that bio-oil vapor evolution is accomplished in a few seconds, and occupying two-thirds of the spatial volume of the reactor as widely reported in the open literature. The model could be advantageous in the virtual design of fast pyrolysis reactors and their optimization to meet economic scales required for distributed or satellite units. - Highlights: ► We model the evolution of pyrolysis products in a fluidized bed via CFD. ► We predict the spontaneous emergence of pyrolysis products. ► We confirm the experimental observation that the kinetics are fast. ► And that bio-oil vapor evolution is accomplished in a few seconds. ► The model is advantageous in the virtual design of fast pyrolysis reactors.

  8. Autochthonous bioaugmentation with environmental samples rich in hydrocarbonoclastic bacteria for bench-scale bioremediation of oily seawater and desert soil.

    Science.gov (United States)

    Ali, Nedaa; Dashti, Narjes; Salamah, Samar; Al-Awadhi, Husain; Sorkhoh, Naser; Radwan, Samir

    2016-05-01

    Oil-contaminated seawater and desert soil batches were bioaugmented with suspensions of pea (Pisum sativum) rhizosphere and soil with long history of oil pollution. Oil consumption was measured by gas-liquid chromatography. Hydrocarbonoclastic bacteria in the bioremediation batches were counted using a mineral medium with oil vapor as a sole carbon source and characterized by their 16S ribosomal RNA (rRNA)-gene sequences. Most of the oil was consumed during the first 2-4 months, and the oil-removal rate decreased or ceased thereafter due to nutrient and oxygen depletion. Supplying the batches with NaNO3 (nitrogen fertilization) at a late phase of bioremediation resulted in reenhanced oil consumption and bacterial growth. In the seawater batches bioaugmented with rhizospheric suspension, the autochthonous rhizospheric bacterial species Microbacterium oxidans and Rhodococcus spp. were established and contributed to oil-removal. The rhizosphere-bioaugmented soil batches selectively favored Arthrobacter nitroguajacolicus, Caulobacter segnis, and Ensifer adherens. In seawater batches bioaugmented with long-contaminated soil, the predominant oil-removing bacterium was the marine species Marinobacter hydrocarbonoclasticus. In soil batches on the other hand, the autochthonous inhabitants of the long-contaminated soil, Pseudomonas and Massilia species were established and contributed to oil removal. It was concluded that the use of rhizospheric bacteria for inoculating seawater and desert soil and of bacteria in long-contaminated soil for inoculating desert soil follows the concept of "autochthonous bioaugmentation." Inoculating seawater with bacteria in long-contaminated soil, on the other hand, merits the designation "allochthonous bioaugmentation."

  9. Experiments on densely-loaded non-Newtonian slurries in laminar and turbulent pipe flows

    Science.gov (United States)

    Mannheimer, R. J.; Grimley, T. A.; Park, J. T.; Morrow, T. B.

    1987-04-01

    The structure of non-Newtonian slurries in laminar, transitional, and turbulent flow regimes in pipes is studied. Experiments are conducted in a large-scale pipe slurry flow facility with an inside pipe diameter of 51 mm. Flow measurements including turbulence quantities such as Reynolds stress are taken with a two-component laser-Doppler velocimeter in a transparent test section with a transparent model slurry. Two transparent model slurries have been developed with non-Newtonian rheological properties. Silica gel particles with diameters on the order of one micron are suspended in two different hydrocarbon liquid mixtures with viscosities of 1.19 and 6.39 cS. In rheological measurements with a concentric cylinder viscometer, slurries from both liquid mixtures exhibited slip. From a linear regression analysis with a power-law model, slurries with the higher viscosity fluid had yield values of 80 and 30 dyn/sq cm for silica gel concentrations of 5.6 and 4.0% by weight, respectively, and the exponents were 0.584 and 0.763. The measured refractive index for the transparent slurries is 1.454 where the difference in refractive index between the fluid and silica gel is estimated to be less than 0.001. Bench scale tests with large diameter silica gel particles on the order of 100 microns have produced slurries with excessive turbidity. A silica gel manufactured by a different process which may form a less turbid slurry is currently under investigation.

  10. Development of the integrated, in-situ remediation technology. Topical report for tasks No. 8 and No. 10 entitled: Laboratory and pilot scale experiments of Lasagna{trademark} process, September 26, 1994--May 25, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Ho, Sa V.; Athmer, C.J.; Sheridan, P.W. [and others

    1997-04-01

    Contamination in low permeability soils poses a significant technical challenge to in-situ remediation efforts. Poor accessibility to the contaminants and difficulty in delivery of treatment reagents have rendered existing in-situ treatments such as bioremediation, vapor extraction, pump and treat rather ineffective when applied to low permeability soils present at many contaminated sites. This technology is an integrated in-situ treatment in which established geotechnical methods are used to install degradation zones directly in the contaminated W and electro-osmosis is utilized to move the contaminants back and forth through those zones until the treatment is completed. This topical report summarizes the results of the lab and pilot sized Lasagna{trademark} experiments conducted at Monsanto. Experiments were conducted with kaofinite and an actual Paducah soil in units ranging from bench-scale containing kg-quantity of soil to pilot-scale containing about half a ton of soil having various treatment zone configurations. The obtained data support the feasibility of scaling up this technology with respect to electrokinetic parameters as well as removal of organic contaminants. A mathematical model was developed that was successful in predicting the temperature rises in the soil. The information and experience gained from these experiments along with the modeling effort enabled us to successfully design and operate a larger field experiment at a DOE TCE-contaminated clay site.

  11. Removal of trace organic chemicals in onsite wastewater soil treatment units: a laboratory experiment.

    Science.gov (United States)

    Teerlink, Jennifer; Martínez-Hernández, Virtudes; Higgins, Christopher P; Drewes, Jörg E

    2012-10-15

    Onsite wastewater treatment is used by 20% of residences in the United States. The ability of these systems, specifically soil treatment units (STUs), to attenuate trace organic chemicals (TOrCs) is not well understood. TOrCs released by STUs pose a potential risk to downstream groundwater and hydraulically-connected surface water that may be used as a drinking water source. A series of bench-scale experiments were conducted using sand columns to represent STUs and to evaluate the efficacy of TOrC attenuation as a function of hydraulic loading rate (1, 4, 8, 12, and 30 cm/day). Each hydraulic loading rate was examined using triplicate experimental columns. Columns were initially seeded with raw wastewater to establish a microbial community, after which they were fed with synthetic wastewater and spiked with 17 TOrCs, in four equal doses per day, to provide a consistent influent water quality. After an initial start-up phase, effluent from all columns consistently demonstrated >90% reductions in dissolved organic carbon and nearly complete (>85%) oxidation of ammonia to nitrate, comparable to the performance of field STUs. The results of this study suggest STUs are capable of attenuating many TOrCs present in domestic wastewater, but attenuation is compound-specific. A subset of TOrCs exhibited an inverse relationship with hydraulic loading rate and attenuation efficiency. Atenolol, cimetidine, and TCPP were more effectively attenuated over time in each experiment, suggesting that the microbial community evolved to a stage where these TOrCs were more effectively biotransformed. Aerobic conditions as compared to anaerobic conditions resulted in more efficient attenuation of acetaminophen and cimetidine. Copyright © 2012. Published by Elsevier Ltd.

  12. Geothermal reservoir engineering research at Stanford University. Third annual report for the period October 1, 1982-September 30, 1983

    Energy Technology Data Exchange (ETDEWEB)

    Ramey, H.J. Jr.; Kruger, P.; Horne, R.N.; Brigham, W.E.; Miller, F.G.

    1983-09-01

    Progress is reported in the following areas: heat extraction from hydrothermal reservoirs; radon reservoir engineering; well test analysis and bench scale experiments; field applications; workshop, seminars, and technical information; reinjection technology; and seismic monitoring of vapor/liquid interfaces. (MHR)

  13. Bench-Scale Silicone Process for Low-Cost CO{sub 2} Capture. Manufacturing Plan for Aminosilicone-based CO{sub 2} Absorption Material

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, Kirkland

    2013-02-01

    A commercially cost effective manufacturing plan was developed for GAP-1m, the aminosilicone-based part of the CO{sub 2} capture solvent described in DE-FE0007502, and the small-scale synthesis of GAP-1m was confirmed. The plan utilizes a current intermediate at SiVance LLC to supply the 2013-2015 needs for GE Global Research. Material from this process was supplied to GE Global Research for evaluation and creation of specifications. GE Global Research has since ordered larger quantities (60 liters) for the larger scale evaluations that start in first quarter, 2013. For GE’s much larger future commercial needs, an improved, more economical pathway to make the product was developed after significant laboratory and literature research. Suppliers were identified for all raw materials.

  14. RADIOACTIVE DEMONSTRATION OF FINAL MINERALIZED WASTE FORMS FOR HANFORD WASTE TREATMENT PLANT SECONDARY WASTE BY FLUIDIZED BED STEAM REFORMING USING THE BENCH SCALE REFORMER PLATFORM

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C.; Burket, P.; Cozzi, A.; Daniel, W.; Jantzen, C.; Missimer, D.

    2012-02-02

    The U.S. Department of Energy's Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford's tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. In addition, the WTP LAW vitrification facility off-gas condensate known as WTP Secondary Waste (WTP-SW) will be generated and enriched in volatile components such as {sup 137}Cs, {sup 129}I, {sup 99}Tc, Cl, F, and SO{sub 4} that volatilize at the vitrification temperature of 1150 C in the absence of a continuous cold cap (that could minimize volatilization). The current waste disposal path for the WTP-SW is to process it through the Effluent Treatment Facility (ETF). Fluidized Bed Steam Reforming (FBSR) is being considered for immobilization of the ETF concentrate that would be generated by processing the WTP-SW. The focus of this current report is the WTP-SW. FBSR offers a moderate temperature (700-750 C) continuous method by which WTP-SW wastes can be processed irrespective of whether they contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be as durable as LAW glass. Monolithing of the granular FBSR product is being investigated to prevent dispersion during transport or burial/storage, but is not necessary for performance. A Benchscale Steam Reformer (BSR) was designed and constructed at the SRNL to treat actual radioactive wastes to confirm the findings of the non-radioactive FBSR pilot scale tests and to qualify the waste form for applications at Hanford. BSR testing with WTP SW waste surrogates and associated analytical analyses and tests of granular products (GP) and monoliths began in the Fall of 2009, and then was continued from the Fall of 2010 through the Spring of 2011. Radioactive testing commenced in 2010 with a demonstration of Hanford's WTP-SW where Savannah River Site (SRS) High Level Waste (HLW) secondary waste from the Defense Waste Processing Facility (DWPF) was shimmed with a mixture of {sup 125/129}I and {sup 99}Tc to chemically resemble WTP-SW. Prior to these radioactive feed tests, non-radioactive simulants were also processed. Ninety six grams of radioactive granular product were made for testing and comparison to the non-radioactive pilot scale tests. The same mineral phases were found in the radioactive and non-radioactive testing.

  15. Hydrothermal and alkaline hydrothermal pretreatments plus anaerobic digestion of sewage sludge for dewatering and biogas production: Bench-scale research and pilot-scale verification.

    Science.gov (United States)

    Li, Chunxing; Wang, Xingdong; Zhang, Guangyi; Yu, Guangwei; Lin, Jingjiang; Wang, Yin

    2017-06-15

    To test the feasibility and practicability of the process combing hydrothermal pretreatment for dewatering with biogas production for full utilization of sewage sludge, hydrothermal/alkaline hydrothermal pretreatments and in turn anaerobic digestion of the filtrates obtained after dewatering the pretreated sludge were performed at bench- and pilot-scales. The hydrothermal temperature fell within the range of 140 °C-220 °C and the pretreatment time varied from 30 min to 120 min. For the alkaline hydrothermal pretreatment the pH value of the sludge was adjusted to 9.0-11.0 by adding Ca(OH) 2 . The results showed that the dewaterability of the sewage sludge was improved with increasing pretreatment temperature but the impact of the pretreatment time was not significant. The addition of Ca(OH) 2 gave better performance on the subsequent mechanical dewatering of the pretreated sludge compared to pure hydrothermal pretreatment, and the higher the pH value was, the better the dewaterability of the pretreated sludge was. The conditions of 180 °C/30 min and 160 °C/60 min/pH = 10.0 (for hydrothermal and alkaline hydrothermal pretreatments, respectively) resulted in relatively good results in the theoretical energy balance, which were verified in the pilot-scale tests. Based on the data from the pilot tests, the alkaline hydrothermal process realized self-sufficiency in energy at the cost of a proper amount of CaO. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. TASK TECHNICAL AND QUALITY ASSURANCE PLAN FOR OUT-OF-TANK DESTRUCTION OF TETRAPHENYLBORATE VIA WET AIR OXIDATION TECHNOLOGY: PHASE I - BENCH SCALE TESTS

    Energy Technology Data Exchange (ETDEWEB)

    Adu-Wusu, K

    2006-03-31

    Tank 48H return to service is critical to the processing of high level waste (HLW) at Savannah River Site (SRS). Liquid Waste Disposition (LWD) management has the goal of returning Tank 48H to routine service by January 2010 or as soon as practical. Tank 48H currently holds legacy material containing organic tetraphenylborate (TPB) compounds from the operation of the In-Tank Precipitation process. This material is not compatible with the waste treatment facilities at SRS and must be removed or undergo treatment to destroy the organic compounds before the tank can be returned to Tank Farm service. Tank 48H currently contains {approx}240,000 gallons of alkaline slurry with about 2 wt % potassium and cesium tetraphenylborate (KTPB and CsTPB). The main radioactive component in Tank 48H is {sup 137}Cs. The waste also contains {approx}0.15 wt % Monosodium Titanate (MST) which has adsorbed {sup 90}Sr, U, and Pu isotopes. A System Engineering Evaluation of technologies/ideas for the treatment of TPB identified Wet Air Oxidation (WAO) as a leading alternative technology to the baseline aggregation approach. Over 75 technologies/ideas were evaluated overall. Forty-one technologies/ideas passed the initial screening evaluation. The 41 technologies/ideas were then combined to 16 complete solutions for the disposition of TPB and evaluated in detail. Wet Air Oxidation (WAO) is an aqueous phase process in which soluble or suspended waste components are oxidized using molecular oxygen contained in air. The process operates at elevated temperatures and pressures ranging from 150 to 320 C and 7 to 210 atmospheres, respectively. The products of the reaction are CO{sub 2}, H{sub 2}O, and low molecular weight oxygenated organics (e.g. acetate, oxalate). The basic flow scheme for a typical WAO system is as follows. The waste solution or slurry is pumped through a high-pressure feed pump. An air stream containing sufficient oxygen to meet the oxygen requirements of the waste stream is injected into the pressurized waste stream, and the air/liquid mixture is preheated to the required reactor inlet temperature. The reactor provides sufficient retention time to allow the oxidation to approach the desired level of organic decomposition. Typical reaction time is about 30-120 minutes. Heat exchangers are routinely employed to recover energy contained in the reactor effluent to preheat the waste feed/air entering the reactor. Auxiliary energy, usually steam, is necessary for startup and can provide trim heat if required. Since the oxidation reactions are exothermic, sufficient energy may be released in the reactor to allow the WAO system to operate without any additional heat input. After cooling, the oxidized reactor effluent passes through a pressure control valve where the pressure is reduced. A separator downstream of the pressure control valve allows the depressurized and cooled vapor to separate from the liquid. Typical industrial WAO applications have a feed flow rate of 1 to 220 gallons per minute (gpm) per train, with a chemical oxygen demand (COD) from 10,000 to 150,000 mg/L (higher CODs with dilution). Note that catalysts, such as homogeneous copper and iron, their heterogeneous counterparts, or precious metals can be used to enhance the effectiveness (i.e., to lower temperature, pressure, and residence time as well as increase oxidation efficiencies) of the WAO reaction if deemed necessary.

  17. Bench-Scale Development of a Hot Carbonate Absorption Process with Crystallization-Enabled High Pressure Stripping for Post-Combustion CO{sub 2} Capture

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yongqi

    2014-02-01

    This report summarizes the methodology and preliminary results of a techno-economic analysis on a hot carbonate absorption process (Hot-CAP) with crystallization-enabled high pressure stripping for post-combustion CO{sub 2} capture (PCC). This analysis was based on the Hot-CAP that is fully integrated with a sub-critical steam cycle, pulverized coal-fired power plant adopted in Case 10 of the DOE/NETL’s Cost and Performance Baseline for Fossil Energy Plants. The techno-economic analysis addressed several important aspects of the Hot-CAP for PCC application, including process design and simulation, equipment sizing, technical risk and mitigation strategy, performance evaluation, and cost analysis. Results show that the net power produced in the subcritical power plant equipped with Hot-CAP is 611 MWe, greater than that with Econoamine (550 MWe). The total capital cost for the Hot-CAP, including CO{sub 2} compression, is $399 million, less than that for the Econoamine PCC ($493 million). O&M costs for the power plant with Hot-CAP is $175 million annually, less than that with Econoamine ($178 million). The 20-year levelized cost of electricity (LCOE) for the power plant with Hot-CAP, including CO2 transportation and storage, is 119.4 mills/kWh, a 59% increase over that for the plant without CO2 capture. The LCOE increase caused by CO{sub 2} capture for the Hot-CAP is 31% lower than that for its Econoamine counterpart.

  18. Generalized Test Plan for the Vitrification of Simulated High-Level -Waste Calcine in the Idaho National Laboratory‘s Bench -Scale Cold Crucible Induction Melter

    Energy Technology Data Exchange (ETDEWEB)

    Vince Maio

    2011-08-01

    This Preliminary Idaho National Laboratory (INL) Test Plan outlines the chronological steps required to initially evaluate the validity of vitrifying INL surrogate (cold) High-Level-Waste (HLW) solid particulate calcine in INL's Cold Crucible Induction Melter (CCIM). Its documentation and publication satisfies interim milestone WP-413-INL-01 of the DOE-EM (via the Office of River Protection) sponsored work package, WP 4.1.3, entitled 'Improved Vitrification' The primary goal of the proposed CCIM testing is to initiate efforts to identify an efficient and effective back-up and risk adverse technology for treating the actual HLW calcine stored at the INL. The calcine's treatment must be completed by 2035 as dictated by a State of Idaho Consent Order. A final report on this surrogate/calcine test in the CCIM will be issued in May 2012-pending next fiscal year funding In particular the plan provides; (1) distinct test objectives, (2) a description of the purpose and scope of planned university contracted pre-screening tests required to optimize the CCIM glass/surrogate calcine formulation, (3) a listing of necessary CCIM equipment modifications and corresponding work control document changes necessary to feed a solid particulate to the CCIM, (4) a description of the class of calcine that will be represented by the surrogate, and (5) a tentative tabulation of the anticipated CCIM testing conditions, testing parameters, sampling requirements and analytical tests. Key FY -11 milestones associated with this CCIM testing effort are also provided. The CCIM test run is scheduled to be conducted in February of 2012 and will involve testing with a surrogate HLW calcine representative of only 13% of the 4,000 m3 of 'hot' calcine residing in 6 INL Bin Sets. The remaining classes of calcine will have to be eventually tested in the CCIM if an operational scale CCIM is to be a feasible option for the actual INL HLW calcine. This remaining calcine's make-up is HLW containing relatively high concentrations of zirconium and aluminum, representative of the cladding material of the reprocessed fuel that generated the calcine. A separate study to define the CCIM testing needs of these other calcine classifications in currently being prepared under a separate work package (WP-0) and will be provided as a milestone report at the end of this fiscal year.

  19. In vitro and in vivo evaluation of amorphous solid dispersions generated by different bench-scale processes, using griseofulvin as a model compound.

    Science.gov (United States)

    Chiang, Po-Chang; Cui, Yong; Ran, Yingqing; Lubach, Joe; Chou, Kang-Jye; Bao, Linda; Jia, Wei; La, Hank; Hau, Jonathan; Sambrone, Amy; Qin, Ann; Deng, Yuzhong; Wong, Harvey

    2013-04-01

    Drug polymer-based amorphous solid dispersions (ASD) are widely used in the pharmaceutical industry to improve bioavailability for poorly water-soluble compounds. Spray-drying is the most common process involved in the manufacturing of ASD material. However, spray-drying involves a high investment of material quantity and time. Lower investment manufacturing processes such as fast evaporation and freeze-drying (lyophilization) have been developed to manufacture ASD at the bench level. The general belief is that the overall performance of ASD material is thermodynamically driven and should be independent of the manufacturing process. However, no formal comparison has been made to assess the in vivo performance of material generated by different processes. This study compares the in vitro and in vivo properties of ASD material generated by fast evaporation, lyophilization, and spray-drying methods using griseofulvin as a model compound and hydroxypropyl methylcellulose acetate succinate as the polymer matrix. Our data suggest that despite minor differences in the formulation release properties and stability of the ASD materials, the overall exposure is comparable between the three manufacturing processes under the conditions examined. These results suggest that fast evaporation and lyophilization may be suitable to generate ASD material for oral evaluation. However, caution should be exercised since the general applicability of the present findings will need to be further evaluated.

  20. Bench-Scale and Pilot-Scale Treatment Technologies for the Removal of Total Dissolved Solids from Coal Mine Water: A Review.

    Data.gov (United States)

    U.S. Environmental Protection Agency — There is no database. This dataset is not publicly accessible because: This is a review manuscript, there was not data generated under this effort. All data used was...

  1. Bench-Scale and Pilot-Scale Treatment Technologies for the Removal of Total Dissolved Solids from Coal Mine Water: A Review

    Science.gov (United States)

    Coal mine water (CMW) is typically treated to remove suspended solids, acidity, and soluble metals, but high concentrations of total dissolved solids (TDS) have been reported to impact the environment at several CMW discharge points. Consequently, various states have establishe...

  2. Increasing Desalination by Mitigating Anolyte pH Imbalance Using Catholyte Effluent Addition in a Multi-Anode Bench Scale Microbial Desalination Cell

    KAUST Repository

    Davis, Robert J.

    2013-09-03

    A microbial desalination cell (MDC) uses exoelectrogenic bacteria to oxidize organic matter while desalinating water. Protons produced from the oxidation of organics at the anode result in anolyte acidification and reduce performance. A new method was used here to mitigate anolyte acidification based on adding non-buffered saline catholyte effluent from a previous cycle to the anolyte at the beginning of the next cycle. This method was tested using a larger-scale MDC (267 mL) containing four anode brushes and a three cell pair membrane stack. With an anolyte salt concentration increased by an equivalent of 75 mM NaCl using the catholyte effluent, salinity was reduced by 26.0 ± 0.5% (35 g/L NaCl initial solution) in a 10 h cycle, compared to 18.1 ± 2.0% without catholyte addition. This improvement was primarily due to the increase in buffering capacity of the anolyte, although increased conductivity slightly improved performance as well. There was some substrate loss from the anolyte by diffusion into the membrane stack, but this was decreased from 11% to 2.6% by increasing the anolyte conductivity (7.6 to 14 mS/cm). These results demonstrated that catholyte effluent can be utilized as a useful product for mitigating anolyte acidification and improving MDC performance. © 2013 American Chemical Society.

  3. Alkali deposits found in biomass boilers: The behavior of inorganic material in biomass-fired power boilers -- Field and laboratory experiences. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, L.L. [Sandia National Labs., Livermore, CA (United States). Combustion Research Facility; Miles, T.R.; Miles, T.R. Jr. [Miles (Thomas R.), Portland, OR (United States); Jenkins, B.M. [California Univ., Davis, CA (United States); Dayton, D.C.; Milne, T.A. [National Renewable Energy Lab., Golden, CO (United States); Bryers, R.W. [Foster Wheeler Development Corp., Livingston, NJ (United States); Oden, L.L. [Bureau of Mines, Albany, OR (United States). Albany Research Center

    1996-03-01

    This report documents the major findings of the Alkali Deposits Investigation, a collaborative effort to understand the causes of unmanageable ash deposits in biomass-fired electric power boilers. Volume 1 of this report provide an overview of the project, with selected highlights. This volume provides more detail and discussion of the data and implications. This document includes six sections. The first, the introduction, provides the motivation, context, and focus for the investigation. The remaining sections discuss fuel properties, bench-scale combustion tests, a framework for considering ash deposition processes, pilot-scale tests of biomass fuels, and field tests in commercially operating biomass power generation stations. Detailed chemical analyses of eleven biomass fuels representing a broad cross-section of commercially available fuels reveal their properties that relate to ash deposition tendencies. The fuels fall into three broad categories: (1) straws and grasses (herbaceous materials); (2) pits, shells, hulls and other agricultural byproducts of a generally ligneous nature; and (3) woods and waste fuels of commercial interest. This report presents a systematic and reasonably detailed analysis of fuel property, operating condition, and boiler design issues that dictate ash deposit formation and property development. The span of investigations from bench-top experiments to commercial operation and observations including both practical illustrations and theoretical background provide a self-consistent and reasonably robust basis to understand the qualitative nature of ash deposit formation in biomass boilers. While there remain many quantitative details to be pursued, this project encapsulates essentially all of the conceptual aspects of the issue. It provides a basis for understanding and potentially resolving the technical and environmental issues associated with ash deposition during biomass combustion. 81 refs., 124 figs., 76 tabs.

  4. Customer experience

    OpenAIRE

    Koperdáková, Zuzana

    2016-01-01

    Bachelor thesis deals with the theme of customer experience and terms related to this topic. The thesis consists of three parts. The first part explains the terms generally, as the experience or customer loyalty. The second part is dedicated to medotology used for Customer Experience Management. In the third part is described application of Customer Experience Management in practice, particularly in the context Touch Point Analyses in GE Money Bank.

  5. OPERA experiment

    International Nuclear Information System (INIS)

    Komatsu, M.

    2003-01-01

    OPERA is an accelerator experiment designed to explore Super-Kamiokande suggested ν μ ↔ν τ oscillation region in CNGS beam from CERN to LNGS. The key technique in OPERA is modern emulsion read out which applied to CHORUS and DONUT experiments. ECC technique which used in DONUT and OPERA has good modularity to enlarge apparatus for future Neutrino Factory experiments

  6. Seabed gallery intakes: Investigation of the water pretreatment effectiveness of the active layer using a long-term column experiment

    KAUST Repository

    Dehwah, Abdullah

    2017-05-11

    Seabed gallery intake systems used for seawater reverse osmosis facilities employ the same principle of water treatment as slow sand filtration in freshwater systems. An investigation concerning the effectiveness of the active layer (top layer) in improving raw water quality was conducted by using a long-term bench-scale columns experiment. Two different media types, silica and carbonate sand, were tested in 1 m columns to evaluate the effectiveness of media type in terms of algae, bacteria, Natural Organic Matter (NOM) and Transparent Exopolymer Particles (TEP) removal over a period of 620 days. Nearly all algae in the silica sand column, 87% (σ = 0.04) of the bacteria, 59% (σ = 0.11) of the biopolymer fraction of NOM, 59% (σ = 0.16) of particulate and 32% (σ = 0.25) of colloidal TEP were removed during the last 330 days of the experiment. Total removal was observed in the carbonate sand column for algal concentration, while the bacterial removal was lower at 74% (σ = 0.08). Removal of biopolymers, particulate and colloidal TEP were higher in the carbonate column during the last 330 days with 72% (σ = 0.15), 66% (σ = 0.08) and 36% (σ = 0.12) removed for these organics respectively. Removal of these key organics through the 1 m thick column, representing the active layer, will likely reduce the rate of biofouling, reduce chemical usage and minimize operating cost in SWRO systems. The data show that the media will require several months at the beginning of operation to reach equilibrium so that high organic removal rates can be achieved. No development of a “schmutzdecke” layer occurred. The experimental results suggest that unlike freshwater slow sand filtration wherein most water treatment occurs in the upper 10 cm, in seawater systems treatment occurs throughout the full active layer depth of 1 m. The results of this study will help in designing and operating seabed gallery intake systems in varied geological conditions.

  7. Seabed gallery intakes: Investigation of the water pretreatment effectiveness of the active layer using a long-term column experiment.

    Science.gov (United States)

    Dehwah, Abdullah H A; Missimer, Thomas M

    2017-09-15

    Seabed gallery intake systems used for seawater reverse osmosis facilities employ the same principle of water treatment as slow sand filtration in freshwater systems. An investigation concerning the effectiveness of the active layer (top layer) in improving raw water quality was conducted by using a long-term bench-scale columns experiment. Two different media types, silica and carbonate sand, were tested in 1 m columns to evaluate the effectiveness of media type in terms of algae, bacteria, Natural Organic Matter (NOM) and Transparent Exopolymer Particles (TEP) removal over a period of 620 days. Nearly all algae in the silica sand column, 87% (σ = 0.04) of the bacteria, 59% (σ = 0.11) of the biopolymer fraction of NOM, 59% (σ = 0.16) of particulate and 32% (σ = 0.25) of colloidal TEP were removed during the last 330 days of the experiment. Total removal was observed in the carbonate sand column for algal concentration, while the bacterial removal was lower at 74% (σ = 0.08). Removal of biopolymers, particulate and colloidal TEP were higher in the carbonate column during the last 330 days with 72% (σ = 0.15), 66% (σ = 0.08) and 36% (σ = 0.12) removed for these organics respectively. Removal of these key organics through the 1 m thick column, representing the active layer, will likely reduce the rate of biofouling, reduce chemical usage and minimize operating cost in SWRO systems. The data show that the media will require several months at the beginning of operation to reach equilibrium so that high organic removal rates can be achieved. No development of a "schmutzdecke" layer occurred. The experimental results suggest that unlike freshwater slow sand filtration wherein most water treatment occurs in the upper 10 cm, in seawater systems treatment occurs throughout the full active layer depth of 1 m. The results of this study will help in designing and operating seabed gallery intake systems in varied geological conditions. Copyright

  8. OPERA experiment

    CERN Document Server

    Komatsu, M

    2003-01-01

    OPERA is an accelerator experiment designed to explore Super- Kamiokande suggested nu//mu arrow left right nu//tau oscillation region in CNGS beam from CERN to LNGS. The key technique in OPERA is modern emulsion read out which applied to CHORUS and DONUT experiments. ECC technique which used in DONUT and OPERA has good modularity to enlarge apparatus for future Neutrino Factory experiments.

  9. TRIO experiment

    Energy Technology Data Exchange (ETDEWEB)

    Clemmer, R.G.; Finn, P.A.; Malecha, R.F.; Misra, B.; Billone, M.C.; Bowers, D.L.; Fischer, A.K.; Greenwood, L.R.; Mattas, R.F.; Tam, S.W.

    1984-09-01

    The TRIO experiment is a test of in-situ tritium recovery and heat transfer performance of a miniaturized solid breeder blanket assembly. The assembly (capsule) was monitored for temperature and neutron flux profiles during irradiation and a sweep gas flowed through the capsule to an anaytical train wherein the amounts of tritium in its various chemical forms were determined. The capsule was designed to operate at different temperatures and sweep gas conditions. At the end of the experiment the amount of tritium retained in the solid was at a concentration of less than 0.1 wppM. More than 99.9% of tritium generated during the experiment was successfully recovered. The results of the experiment showed that the tritium inventories at the beginning and at the end of the experiment follow a relationship which appears to be characteristic of intragranular diffusion.

  10. Pixel Experiments

    DEFF Research Database (Denmark)

    Petersen, Kjell Yngve; Søndergaard, Karin; Augustesen, Christina

    2015-01-01

    Pixel Experiments The term pixel is traditionally defined as any of the minute elements that together constitute a larger context or image. A pixel has its own form and is the smallest unit seen within a larger structure. In working with the potentials of LED technology in architectural lighting...... for using LED lighting in lighting design practice. The speculative experiments that have been set-up have aimed to clarify the variables that can be used as parameters in the design of lighting applications; including, for example, the structuring and software control of light. The experiments also...... elucidate and exemplify already well-known problems in relation to the experience of vertical and horizontal lighting. Pixel Experiments exist as a synergy between speculative test setups and lighting design in practice. This book is one of four books that is published in connection with the research...

  11. Collaborative experience

    DEFF Research Database (Denmark)

    Mortensen, Thomas Bøtker

    Literature review: Collaborative experience has been shown to have a positive effect on the collaborative outcome in general (Anand & Khanna, 2000; Kale, Dyer & Singh, 2002). Furthermore, it has been linked to the ability to exploit the network of the firm for learning (Powell, Koput and Smith...... experience was largest the higher the hypothesized ambiguity. Theoretically contribution: This research project aims at contributing to existing literature by arguing, that collaborative experience is a moderating variable which moderates the effects on collaborative outcome from the level of complexity......, that the largest effects from collaborative experience is from recent collaborative experience, since knowledge depreciates when it is not used. Methodologically contribution: The research project studies the dyad and aims at introducing, to this field of research, an established way of collecting data, a new...

  12. Mixture Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Piepel, Gregory F.

    2007-12-01

    A mixture experiment involves combining two or more components in various proportions or amounts and then measuring one or more responses for the resulting end products. Other factors that affect the response(s), such as process variables and/or the total amount of the mixture, may also be studied in the experiment. A mixture experiment design specifies the combinations of mixture components and other experimental factors (if any) to be studied and the response variable(s) to be measured. Mixture experiment data analyses are then used to achieve the desired goals, which may include (i) understanding the effects of components and other factors on the response(s), (ii) identifying components and other factors with significant and nonsignificant effects on the response(s), (iii) developing models for predicting the response(s) as functions of the mixture components and any other factors, and (iv) developing end-products with desired values and uncertainties of the response(s). Given a mixture experiment problem, a practitioner must consider the possible approaches for designing the experiment and analyzing the data, and then select the approach best suited to the problem. Eight possible approaches include 1) component proportions, 2) mathematically independent variables, 3) slack variable, 4) mixture amount, 5) component amounts, 6) mixture process variable, 7) mixture of mixtures, and 8) multi-factor mixture. The article provides an overview of the mixture experiment designs, models, and data analyses for these approaches.

  13. Simulated experiments

    International Nuclear Information System (INIS)

    Bjerknes, R.

    1977-01-01

    A cybernetic model has been developed to elucidate some of the main principles of the growth regulation system in the epidermis of the hairless mouse. A number of actual and theoretical biological experiments have been simulated on the model. These included simulating the cell kinetics as measured by pulse labelling with tritiated thymidine and by continuous labelling with tritiated thymidine. Other simulated experiments included steady state, wear and tear, painting with a carcinogen, heredity and heredity and tumour. Numerous diagrams illustrate the results of these simulated experiments. (JIW)

  14. Researching experiences

    DEFF Research Database (Denmark)

    Gjedde, Lisa; Ingemann, Bruno

    , dialogue, moods, values and narratives have been investigated qualitatively with more than sixty informants in a range of projects. The processual methodological insights are put into a theoretical perspective and also presented as pragmatic dilemmas. Researching Experiences is relevant not only...... for students and researchers in media and communication studies but also for practitioners within the fields of media, communication and experience design....... for researching experiences in a variety of settings ranging from the museum, to news photography, and interactive media. The research led to the development of a set of methodological tools and approaches we term the reflexivity lab. The interaction in the experimental situation between the media and body...

  15. Researching experiences

    DEFF Research Database (Denmark)

    Gjedde, Lisa; Ingemann, Bruno

    In the beginning was - not the word - but the experience. This phenomenological approach provides the basis for this book, which focuses on how a person-in-situation experiences and constructs meaning from a variety of cultural visual events. This book presents video-based processual methods...... for researching experiences in a variety of settings ranging from the museum, to news photography, and interactive media. The research led to the development of a set of methodological tools and approaches we term the reflexivity lab. The interaction in the experimental situation between the media and body......, dialogue, moods, values and narratives have been investigated qualitatively with more than sixty informants in a range of projects. The processual methodological insights are put into a theoretical perspective and also presented as pragmatic dilemmas. Researching Experiences is relevant not only...

  16. Interpretive Experiments

    Science.gov (United States)

    DeHaan, Frank, Ed.

    1977-01-01

    Describes an interpretative experiment involving the application of symmetry and temperature-dependent proton and fluorine nmr spectroscopy to the solution of structural and kinetic problems in coordination chemistry. (MLH)

  17. Antimatter Experiments

    CERN Multimedia

    2004-01-01

    Antimatter should behave in identical fashion to matter if a form of spacetime symmetry called CPT invariance holds. Two experiments at CERN near Geneva are testing this hypothesis using antihydrogen atoms

  18. Media experiences

    DEFF Research Database (Denmark)

    Buhl, Mie

    2010-01-01

    on their particular iconic systems of meaning perceived through form, lines, contrasts, colours, structures textures, rhythm and composite qualities with embedded interdependent codes and culturally conditioned potential for construction of knowledge and meaning. Mediated experience adds new perspectives...

  19. Experiment Databases

    Science.gov (United States)

    Vanschoren, Joaquin; Blockeel, Hendrik

    Next to running machine learning algorithms based on inductive queries, much can be learned by immediately querying the combined results of many prior studies. Indeed, all around the globe, thousands of machine learning experiments are being executed on a daily basis, generating a constant stream of empirical information on machine learning techniques. While the information contained in these experiments might have many uses beyond their original intent, results are typically described very concisely in papers and discarded afterwards. If we properly store and organize these results in central databases, they can be immediately reused for further analysis, thus boosting future research. In this chapter, we propose the use of experiment databases: databases designed to collect all the necessary details of these experiments, and to intelligently organize them in online repositories to enable fast and thorough analysis of a myriad of collected results. They constitute an additional, queriable source of empirical meta-data based on principled descriptions of algorithm executions, without reimplementing the algorithms in an inductive database. As such, they engender a very dynamic, collaborative approach to experimentation, in which experiments can be freely shared, linked together, and immediately reused by researchers all over the world. They can be set up for personal use, to share results within a lab or to create open, community-wide repositories. Here, we provide a high-level overview of their design, and use an existing experiment database to answer various interesting research questions about machine learning algorithms and to verify a number of recent studies.

  20. Researching Experiences

    DEFF Research Database (Denmark)

    Gjedde, Lisa; Ingemann, Bruno

    In the beginning was - not the word - but the experience. This phenomenological approach provides the basis for this book, which focuses on how a person-in-situation experiences and constructs meaning from a variety of cultural visual events. This book presents video-based processual methods for ...... for students and researchers in media and communication studies but also for practitioners within the fields of media, communication and experience design.......In the beginning was - not the word - but the experience. This phenomenological approach provides the basis for this book, which focuses on how a person-in-situation experiences and constructs meaning from a variety of cultural visual events. This book presents video-based processual methods...... for researching experiences in a variety of settings ranging from the museum, to news photography, and interactive media. The research led to the development of a set of methodological tools and approaches we term the ReflexivityLab. The interaction in the experimental situation between the media and body...

  1. The experience of an experience

    DEFF Research Database (Denmark)

    Rasmussen, Alexandra Marie

    2016-01-01

    This paper examines a popular phenomenon that allows us to see ourselves from various perspectives, and allows us to perpetuate moments enabling us to relive experiences in a different state of mind or at a different time. To examine the phenomenon of experiencing an experience hermeneutic...... is a tool to create a particular mindset, in the developer, to generate a new way of thinking. This model is dynamic by nature and although it is not completed in every branch, it is complete in relation to experiencing your own experience. A company can apply the PoC to gain insight into primary...

  2. The Experiment

    Science.gov (United States)

    Mariana Nicoara, Floare

    2016-04-01

    My name is Nicoara Floarea and I am teacher at Secondary School Calatele and I teach students from preparatory class and the second grade . They are six-eight years old. In my activity, for introducing scientific concepts to my students, I use various and active methods or traditional methods including experiments. The experiment stimulates students' curiosity, their creativity, the understanding and knowledge taught accessibility. I propose you two such experiments: The life cycle of the plants (long-term experiment, with rigorous observation time):We use beans, wheat or other; They are grown in pots and on the cotton soaked with water,keeping under students' observation protecting them ( just soak them regularly) and we waiting the plants rise. For discussions and comments of plant embryo development we use the plants which rose on the cotton soaked with water plants at the end of the first week. Last school year we had in the pot climbing beans which in May made pods. They were not too great but our experiment was a success. The students could deduce that there will develop those big beans which after drying will be planted again. The influence of light on plants (average duration experiment with the necessary observation time): We use two pots in which plants are of the same type (two geraniums), one of them is situated so as to get direct sunlight and other plant we put in a closed box. Although we wet both plants after a week we see that the plant that benefited from sunlight has turned strain in direct sunlight, developing normally in return the plant out of the box I have yellowed leaves, photosynthesis does not She has occurred . Students will understand the vital role of the Sun in plants' life, both in the classroom and in nature. The experiment is a method of teaching students extremely pleasant, with a remarkable percentage of acquiring more knowledge.

  3. Pixel Experiments

    DEFF Research Database (Denmark)

    Søndergaard, Karin; Petersen, Kjell Yngve; Augustesen, Christina

    2015-01-01

    Pixel Experiments The term pixel is traditionally defined as any of the minute elements that together constitute a larger context or image. A pixel has its own form and is the smallest unit seen within a larger structure. In working with the potentials of LED technology in architectural lighting...... design it became relevant to investigate the use of LEDs as the physical equivalent of a pixel as a design approach. In this book our interest has been in identifying how the qualities of LEDs can be used in lighting applications. With experiences in the planning and implementation of architectural...... lighting design in practice, one quickly experiences and realises that there are untapped potentials in the attributes of LED technology. In this research, speculative studies have been made working with the attributes of LEDs in architectural contexts, with the ambition to ascertain new strategies...

  4. Researching Experiences

    DEFF Research Database (Denmark)

    Gjedde, Lisa; Ingemann, Bruno

    , dialogue, moods, values and narratives have been investigated qualitatively with more than sixty informants in a range of projects. The processual methodological insights are put into a theoretical perspective and also presented as pragmatic dilemmas.      Researching Experiences is relevant not only...... for students and researchers in media and communication studies but also for practitioners within the fields of media, communication and experience design....... for researching experiences in a variety of settings ranging from the museum, to news photography, and interactive media. The research led to the development of a set of methodological tools and approaches we term the ReflexivityLab. The interaction in the experimental situation between the media and body...

  5. Catalytic tar removal from biomass producer gas with secondary air

    Energy Technology Data Exchange (ETDEWEB)

    Lammers, G.; Beenackers, A.A.C.M. [University of Groningen (Netherlands). Dept. of Chemical Engineering; Corella, J. [Universidad Complutense, Madrid (Spain)

    1997-12-31

    The effect of air addition on biomass tar conversion in catalytic packed bed crackers was studied using both an isothermal micro reactor and a fluidised bed bench scale biomass gasification set up with down stream tar crackers. The micro reactor was applied for experiments with artificial biomass producer gas containing naphthalene as a model tar compound. Experiments were carried out with inert silica and catalytically active calcined dolomite bed material both with and without air addition. Experimental results with real tar from the fluidised bed bench scale gasification set up were in qualitative agreement with results from the micro reactor experiments. (author)

  6. EXPERIENCE WITH

    African Journals Online (AJOL)

    SURGERY DEPT

    Abstract. Background:Island flap techniques currently used in urethroplasty utilize the prepuce and the dorsal penile skin. Our experience with a one-stage island flap urethroplasty for urethral strictures utilizing the ventral penile skin is described. Patients and Method: This is a longitudinal study of seventy six consecutive ...

  7. Sulfur-Iodine Integrated Lab Scale Experiment Development

    International Nuclear Information System (INIS)

    Russ, Ben

    2011-01-01

    The sulfur-iodine (SI) cycle was determined to be the best cycle for coupling to a high temperature reactor (HTR) because of its high efficiency and potential for further improvement. The Japanese Atomic Energy Agency (JAEA) has also selected the SI process for further development and has successfully completed bench-scale demonstrations of the SI process at atmospheric pressure. JEA also plans to proceed with pilot-scale demonstrations of the SI process and eventually plans to couple an SI demonstration plant to its High Temperature Test Reactor (HHTR). As part of an international NERI project, GA, SNL, and the Frech Commissariat L'Energie Atomique performed laboratory-scale demonstrations of the SI process at prototypical temperatures and pressures. This demonstration was performed at GA in San Diego, CA and concluded in April 2009.

  8. Sulfur-Iodine Integrated Lab Scale Experiment Development

    Energy Technology Data Exchange (ETDEWEB)

    Russ, Ben

    2011-05-27

    The sulfur-iodine (SI) cycle was deermined to be the best cycle for coupling to a high temperature reactor (HTR) because of its high efficiency and potential for further improvement. The Japanese Atomic Energy Agency (JAEA) has also selected the SI process for further development and has successfully completed bench-scale demonstrations of the SI process at atmospheric pressure. JEA also plans to proceed with pilot-scale demonstrations of the SI process and eventually plans to couple an SI demonstration plant to its High Temperature Test Reactor (HHTR). As part of an international NERI project, GA, SNL, and the Frech Commissariat L'Energie Atomique performed laboratory-scale demonstrations of the SI process at prototypical temperatures and pressures. This demonstration was performed at GA in San Diego, CA and concluded in April 2009.

  9. Extending Experiences

    DEFF Research Database (Denmark)

    A computer game's player is experiencing not only the game as a designer-made artefact, but also a multitude of social and cultural practices and contexts of both computer game play and everyday life. As a truly multidisciplinary anthology, Extending Experiences sheds new light on the mesh...... of possibilities and influences the player engages with. Part one, Experiential Structures of Play, considers some of the key concepts commonly used to address the experience of a computer game player. The second part, Bordering Play, discusses conceptual and practical overlaps of games and everyday life...... and the impacts of setting up, crossing and breaking the boundaries of game and non-game. Part three, Interfaces of Play, looks at games as technological and historical artefacts and commodities. The fourth part, Beyond Design, introduces new models for the practical and theoretical dimensions of game design....

  10. Dirac experiment

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, F.; Adeva, B.; Afanasev, L.; Benayoun, M.; Brekhovskikh, V.; Caragheorgheopol, G.; Cechak, T.; Chiba, M.; Constantinescu, S.; Doudarev, A.; Dreossi, D.; Drijard, D.; Ferro-Luzzi, M.; Gallas, M.V.; Gerndt, J.; Giacomich, R.; Gianotti, P.; Goldin, D.; Gorin, A.; Gortchakov, O.; Guaraldo, C.; Hansroul, M.; Hosek, R.; Iliescu, M.; Jabitski, M.; Kalinina, N.; Karpoukhine, V.; Kluson, J.; Kobayashi, M.; Kokkas, P.; Komarov, V.; Koulikov, A.; Kouptsov, A.; Krouglov, V.; Krouglova, L.; Kuroda, K.-I.; Lanaro, A.; Lapshine, V.; Lednicky, R.; Leruste, P.; Levisandri, P.; Lopez Aguera, A.; Lucherini, V.; Maki, T.; Manuilov, I.; Montanet, L.; Narjoux, J.-L.; Nemenov, L.; Nikitin, M.; Nunez Pardo, T.; Okada, K.; Olchevskii, V.; Pazos, A.; Pentia, M.; Penzo, A.; Perreau, J.-M.; Petrascu, C.; Plo, M.; Ponta, T.; Pop, D.; Riazantsev, A.; Rodriguez, J.M.; Rodriguez Fernandez, A.; Rykaline, V.; Santamarina, C.; Saborido, J.; Schacher, J.; Sidorov, A.; Smolik, J.; Takeutchi, F.; Tarasov, A.; Tauscher, L.; Tobar, M.J.; Trusov, S.; Vazquez, P.; Vlachos, S.; Yazkov, V.; Yoshimura, Y.; Zrelov, P

    2001-04-01

    The main objective of DIRAC experiment is the measurement of the lifetime {tau} of the exotic hadronic atom consisting of {pi}{sup +} and {pi}{sup -} mesons. The lifetime of this atom is determined by the decay mode {pi}{sup +} {pi}{sup -} {yields} {pi}{sup 0} {pi}{sup 0} due to the strong interaction. Through the precise relationship between the lifetime and the S-wave pion-pion scattering length difference |a{sub 0} - a{sub 2}| for isospin 0 and 2 (respectively), a measurement of {tau} with an accuracy of 10% will allow a determination of |a{sub 0} - a{sub 2}| at a 5% precision level. Pion-pion scattering lengths have been calculated in the framework of chiral perturbation theory with an accuracy below 5%. In this way DIRAC experiment will provide a crucial test of the chiral symmetry breaking scheme in QCD effective theories at low energies.

  11. Dirac experiment

    CERN Document Server

    Gómez, F; Afanasev, L; Benayoun, M; Brekhovskikh, V; Caragheorgheopol, G; Cechák, T; Chiba, M; Constantinescu, S; Doudarev, A; Dreossi, D; Drijard, Daniel; Ferro-Luzzi, M; Gallas, M V; Gerndt, J; Giacomich, R; Gianotti, P; Goldin, D; Gorin, A; Gortchakov, O; Guaraldo, C; Hansroul, M; Hosek, R; Iliescu, M; Jabitski, M; Kalinina, N; Karpoukhine, V; Kluson, J; Kobayshi, M; Kokkas, P; Komarov, V; Koulikov, A; Kouptsov, A; Krouglov, V; Krouglova, L; Kuroda, K I; Lanaro, A; Lapshine, B; Lednicky, R; Leruste, P; Levisandri, P; López-Aguera, A; Lucherini, V; Mäki, T; Manuilov, I; Montanet, L; Narjoux, J L; Nemenov, L; Nikitin, M; Nunez Pardo, T; Okada, K; Olchevskii, V; Pazos, A; Pentia, M; Penzo, Aldo L; Perreau, J M; Petrascu, C; Pló, M; Ponta, T; Pop, D; Riazantsev, A; Rodríguez, J M; Rodriguez Fernandez, A; Rykaline, V; Santamarina, C; Saborido, J; Schacher, J; Sidorov, A; Smolik, J; Takeutchi, F; Tarasov, A; Tauscher, L; Tobar, M J; Trusov, S; Vasquez, P; Vlachos, S; Yazkov, V; Yoshimura, Y; Zrelov, P

    2001-01-01

    The main objective of DIRAC experiment is the measurement of the lifetime tau of the exotic hadronic atom consisting of pi /sup +/ and pi /sup -/ mesons. The lifetime of this atom is determined by the decay mode pi /sup +/ pi /sup -/ to pi /sup 0/ pi /sup 0/ due to the strong interaction. Through the precise relationship between the lifetime and the S-wave pion-pion scattering length difference a/sub 0/-a/sub 2/ for isospin 0 and 2 (respectively), a measurement of tau with an accuracy of 10% will allow a determination of a/sub 0/-a/sub 2/at a 5% precision level. Pion-pion scattering lengths have been calculated in the framework of chiral perturbation theory with an accuracy below 5%. In this way DIRAC experiment will provide a crucial test of the chiral symmetry breaking scheme in QCD effective theories at low energies. (19 refs).

  12. Experiment 7

    CERN Multimedia

    CERN PhotoLab

    1968-01-01

    Over-all view of the arrangement of counters around the polarized target in the kaon-polarized proton experiment. The beam enters through the quadrupole magnet on the left, and strikes the target placed in a 18.5 kG field (one pole of the magnet is just visible above the ring of counters). The scatterred kaon and recoil proton are detected by the counters on the ring and recorded onto magnetic tape.

  13. QUBIC Experiment

    OpenAIRE

    Stolpovskiy, Mikhail

    2016-01-01

    QUBIC is a ground-based experiment, currently under construction, that uses the novel bolometric interferometry technology. It is dedicated to measure the primordial B-modes of CMB. As a bolometric interferometer, QUBIC has high sensitivity and good systematics control. Dust contamination is controlled by operating with two bands -- 150 and 220 GHz. There are two possible sites for QUBIC: either Concordia station in Antarctic or in the Argentinian Puna desert. It is planned to see the first l...

  14. Experiments expectations

    OpenAIRE

    Gorini, B; Meschi, E

    2014-01-01

    This paper presents the expectations and the constraints of the experiments relatively to the commissioning procedure and the running conditions for the 2015 data taking period. The views about the various beam parameters for the p-p period, like beam energy, maximum pileup, bunch spacing and luminosity limitation in IP2 and IP8, are discussed. The goals and the constraints of the 2015 physics program are also presented, including the heavy ions period as well as the special...

  15. On-site treatment and landfilling of MSWI air pollution control residues

    DEFF Research Database (Denmark)

    Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

    2003-01-01

    Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are difficult to landfill due to substantial leaching of trace metals. An on-site pretreatment prior to landfilling of APC-residues was investigated in terms of bench-scale experiments with a semidry APC-residue a......Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are difficult to landfill due to substantial leaching of trace metals. An on-site pretreatment prior to landfilling of APC-residues was investigated in terms of bench-scale experiments with a semidry APC...

  16. Experimenting with a design experiment

    Directory of Open Access Journals (Sweden)

    Bakker, Judith

    2012-12-01

    Full Text Available The design experiment is an experimental research method that aims to help design and further develop new (policy instruments. For the development of a set of guidelines for the facilitation of citizens’ initiatives by local governments, we are experimenting with this method. It offers good opportunities for modeling interventions by testing their instrumental validity –the usefulness for the intended practical purposes. At the same time design experiments are also useful for evaluating the empirical validity of theoretical arguments and the further development of these arguments in the light of empirical evidence (by using e.g. the technique of pattern matching. We describe how we have applied this methodology in two cases and discuss our research approach. We encountered some unexpected difficulties, especially in the cooperation with professionals and citizens. These difficulties complicate the valid attribution of causal effects to the use of the new instrument. However, our preliminary conclusion is that design experiments are useful in our field of study

    El experimento de diseño es un método de investigación experimental que tiene como objetivo diseñar y desarrollar posteriormente nuevas herramientas (políticas. En este artículo experimentamos con este método para desarrollar un conjunto de directrices que permitan a los gobiernos locales facilitar las iniciativas ciudadanas. El método ofrece la oportunidad de modelar las intervenciones poniendo a prueba su validez instrumental (su utilidad para el fin práctico que se proponen. Al mismo tiempo, los experimentos de diseño son útiles también para evaluar la validez empírica de las discusiones teóricas y el posterior desarrollo de esas discusiones a la luz de la evidencia empírica (usando, por ejemplo, técnicas de concordancia de patrones. En este trabajo describimos cómo hemos aplicado este método a dos casos y discutimos nuestro enfoque de

  17. Operating experience

    International Nuclear Information System (INIS)

    McRae, L.P.; Six, D.E.

    1991-01-01

    In 1987, Westinghouse Hanford Company began operating a first-generation integrated safeguards system in the Plutonium Finishing Plant storage vaults. This Vault Safety and Inventory System is designed to integrate data into a computer-based nuclear material inventory monitoring system. The system gathers, in real time, measured physical parameters that generate nuclear material inventory status data for thousands of stored items and sends tailored report to the appropriate users. These data include canister temperature an bulge data reported to Plant Operations and Material Control and Accountability personnel, item presence and identification data reported to Material Control and Accountability personnel, and unauthorized item movement data reported to Security response forces and Material Control and Accountability personnel. The Westinghouse Hanford Company's experience and operational benefits in using this system for reduce radiation exposure, increase protection against insider threat, and real-time inventory control are discussed in this paper

  18. Management Experiences

    Directory of Open Access Journals (Sweden)

    Gheorghe Popovici

    2016-12-01

    Full Text Available The paper presents the results of the survey about the changes in modern management, identified from the experience of Romanian managers. By this online study one presents both the obstacles encountered and the recommendations for such a type of management that the present and future mangers must take into account. What motivated the respondent Romanian managers most to open their own business is the independence it offered them. They work in the field they have liked since they were young. The second reason was the perspective to have an additional income from the business development. The third argument in favour of opening a business is the possibility to assure the balance between personal life and career.

  19. Particle physics experiments 1983

    International Nuclear Information System (INIS)

    Stuart, G.W.

    1983-01-01

    The report describes work carried out in 1983 on experiments approved by the Particle Physics Experiments Selection Panel. The contents consist of unedited contributions from each experiment. (author)

  20. Radioactive demonstration of final mineralized waste forms for Hanford waste treatment plant secondary waste (WTP-SW) by fluidized bed steam reforming (FBSR) using the bench scale reformer platform

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Jantzen, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-08-01

    The U.S. Department of Energy’s Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford’s tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. In addition, the WTP LAW vitrification facility off-gas condensate known as WTP Secondary Waste (WTP-SW) will be generated and enriched in volatile components such as 137Cs, 129I, 99Tc, Cl, F, and SO4 that volatilize at the vitrification temperature of 1150°C in the absence of a continuous cold cap (that could minimize volatilization). The current waste disposal path for the WTP-SW is to process it through the Effluent Treatment Facility (ETF). Fluidized Bed Steam Reforming (FBSR) is being considered for immobilization of the ETF concentrate that would be generated by processing the WTP-SW. The focus of this current report is the WTP-SW.

  1. An integrated practical implementation of continuous aqueous two-phase systems for the recovery of human IgG: From the microdevice to a multistage bench-scale mixer-settler device.

    Science.gov (United States)

    Espitia-Saloma, Edith; Vâzquez-Villegas, Patricia; Rito-Palomares, Marco; Aguilar, Oscar

    2016-05-01

    Aqueous two-phase systems (ATPS) are a liquid-liquid extraction technology with clear process benefits; however, its lack of industrial embracement is still a challenge to overcome. Antibodies are a potential product to be recovered by ATPS in a commercial context. The objective of this work is to present a more integral approach of the different isolated strategies that have arisen in order to enable a practical, generic implementation of ATPS, using human immunoglobulin G (IgG) as experimental model. A microfluidic device is used for ATPS parameters preselection for product recovery. ATPS were continuously operated in a mixer-settler device in one stage, multistage and multistage with recirculation configuration. Single-stage pure IgG extraction with a polyethylene glycol (PEG) 3350-phophates ATPS within continuous operation allowed a 65% recovery. Further implementation of a multistage platform promoted a higher particle partitioning reaching a 90% recovery. The processing of IgG from a cell supernatant culture harvest in a multistage system with top phase recirculation resulted in 78% IgG recovery in bottom phase. This work conjugates three not widely spread methodologies for ATPS: microfluidics, continuous and multistage operation. Copyright © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Effect of solids retention time on Microthrix parvicella growth ...

    African Journals Online (AJOL)

    The objective of this study was to evaluate the effect of solids retention time (SRT) on M. parvicella growth and to calculate growth kinetic parameters of this filamentous species. Bench-scale continuous-flow experiments showed that M. parvicella growth can be significantly suppressed at an SRT of lower than 5.7 d for ...

  3. Experimental and theoretical study of combined solvent and steam stripping of 1,2,3,4,5,6-hexachlorocyclohexane (HCH) and mercury from contaminated natural soil

    NARCIS (Netherlands)

    Brouwers, Jos

    1996-01-01

    This paper reports on an experimental and theoretical study of the combined solvent and steam stripping of contaminated soil. First, feasibility experiments on the bench scale are reported concerning the stripping of soil contaminated with 1,2,3,4,5,6-hexachlorocyclohexane (HCH) and mercury. This

  4. Bacterial Mercury Methylation At The Sediment-Water Interface Of Mercury Contaminated Sediments

    Science.gov (United States)

    Bench scale experiments were conducted to improve our understanding of bacterial mediation of mercury transformation (methylation), specifically those factors which govern the production of methyl mercury (MeHg) at the sediment-water interface. The greatest cause for concern re...

  5. Phosphorus release from decomposing water hyacinth and effects of ...

    African Journals Online (AJOL)

    Mo

    Abstract. Bench scale experiments were done to assess the effects of decomposition of water hyacinth on phosphorus release and water quality. Hyacinth plants from the lake were chopped to fine pieces. In replicate incubation tubes, 50 g of plant material was stocked to which 1.6 L of lake water was added. One set was ...

  6. Coulombic interactions during advection-dominated transport of ions in porous media

    DEFF Research Database (Denmark)

    Muniruzzaman, Muhammad; Stolze, Lucien; Rolle, Massimo

    2017-01-01

    bench-scale experiments and numerical simulations. The investigation aims at quantifying the key role of small-scale electrostatic interactions in flow-through systems, especially when advection is the dominant mass-transfer process. Considering dilute solutions of strong electrolytes (e.g., MgCl2...

  7. 2018-03-08T08:37:09Z https://www.ajol.info/index.php/all/oai oai:ojs ...

    African Journals Online (AJOL)

    Maleic acid and oxalic acid in the ozonized wastewater were degraded completely by the activated sludge in shake-flasks and bench-scale aerated bioreactor experiments. The immobilized activated sludge culture using polyurethane foam (PUF) was most effective in degrading organic acids in continuous culture condition ...

  8. Alternative fuels in cement industry; Alternativa braenslen i cementindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Nyman, K.E.; Ek, R. [Finnsementti Oy, Parainen (Finland); Maekelae, K. [Finreci Oy (Finland)

    1997-10-01

    In this project the cement industry`s possibilities to replace half of the fossil fuels with waste derived fuels are investigated. Bench-scale experiments, pilot plant tests and full scale tests have been done with used tires and plastics wastes

  9. Sleep Monitoring Experiment - Skylab Experiment M133

    Science.gov (United States)

    1970-01-01

    This 1970 photograph shows equipment for the Skylab's Sleep Monitoring Experiment (M133), a medical evaluation designed to objectively determine the amount and quality of crewmembers' inflight sleep. The experiment monitored and recorded electroencephalographic (EEG) and electrooculographic (EOG) activity during astronauts' sleep periods. One of the astronauts was selected for this experiment and wore a fitted cap during his sleep periods. The Marshall Space Flight Center had program management responsibility for the development of Skylab hardware and experiments.

  10. Design of modern experiments

    International Nuclear Information System (INIS)

    Park, Sung Hweon

    1984-03-01

    This book is for researchers and engineers, which is written to focus on practical design of experiments. It gives descriptions of conception of design of experiments, basic statistics theory, one way design of experiment, two-way layout without repetition, two-way layout with repetition, partition, a correlation analysis and regression analysis, latin squares, factorial design, design of experiment by table of orthogonal arrays, design of experiment of response surface, design of experiment on compound, Evop, and design of experiment of taguchi.

  11. Data acquisition. GRAAL experiment. Hybrid reactor experiment. AMS experiment

    International Nuclear Information System (INIS)

    Barancourt, D.; Barbier, G.; Bosson, G.; Bouvier, J.; Gallin-Martel, L.; Meillon, B.; Stassi, P.; Tournier, M.

    1997-01-01

    The main activity of the data acquisition team has consisted in hardware and software developments for the GRAAL experiment with the trigger board, for the 'Reacteurs Hybrides' group with an acquisition board ADCVME8V and for the AMS experiment with the monitoring of the aerogel detector. (authors)

  12. Particle physics experiments 1989

    International Nuclear Information System (INIS)

    Bairstow, R.

    1990-01-01

    This report describes work carried out in 1989 on experiments approved by the Particle Physics Experiments Selection Panel of Rutherford Appleton Laboratory. The contents consist of unedited contributions from each experiment. (author)

  13. Particle physics experiments

    International Nuclear Information System (INIS)

    Stuart, G.W.

    1986-01-01

    The report of the Rutherford Appleton Laboratory describes the work carried out in 1985 on experiments approved by the Particle Physics Experiments Selection Panel. The contents consist of unedited contributions from each experiment. (author)

  14. Particle physics experiments 1987

    International Nuclear Information System (INIS)

    Stuart, G.W.

    1988-01-01

    This report describes work carried out in 1987 on experiments approved by the Particle Physics Experiments Selection Panel (United Kingdom). The contents consist of unedited contributions from each experiment. (author)

  15. Particle physics experiments 1986

    International Nuclear Information System (INIS)

    Stuart, G.W.

    1987-01-01

    The paper presents research work carried out in 1986 on 52 elementary particle experiments approved by the Particle Physics Experiments Selection Panel. Most of the experiments were collaborative and involved research groups from different countries. About half of the experiments were conducted at CERN, the remaining experiments employed the accelerators: LAMPT, LEP, PETRA, SLAC, and HERA. The contents consist of unedited contributions from each experiment. (U.K.)

  16. Data acquisition. GRAAL experiment. Hybrid reactor experiment. AMS experiment; Acquisition de donnees. Experience GRAAL. Experience reacteurs hybrides. Experience AMS

    Energy Technology Data Exchange (ETDEWEB)

    Barancourt, D.; Barbier, G.; Bosson, G.; Bouvier, J.; Gallin-Martel, L.; Meillon, B.; Stassi, P.; Tournier, M. [Inst. des Sciences Nucleaires, Grenoble-1 Univ., 38 (France)

    1997-12-31

    The main activity of the data acquisition team has consisted in hardware and software developments for the GRAAL experiment with the trigger board, for the `Reacteurs Hybrides` group with an acquisition board ADCVME8V and for the AMS experiment with the monitoring of the aerogel detector. (authors) 2 figs.

  17. Particle physics experiments 1982

    International Nuclear Information System (INIS)

    Rousseau, M.D.; Stuart, G.

    1983-01-01

    Work carried out in 1982 on 52 experiments approved by the Particle Physics Experiments Selection Panel is described. Each experiment is listed under title, collaboration, technique, accelerator, year of running, status and spokesman. Unedited contributions are given from each experiment. (U.K.)

  18. The User Experience

    Science.gov (United States)

    Schmidt, Aaron

    2010-01-01

    User experience (UX) is about arranging the elements of a product or service to optimize how people will interact with it. In this article, the author talks about the importance of user experience and discusses the design of user experiences in libraries. He first looks at what UX is. Then he describes three kinds of user experience design: (1)…

  19. Indian summer monsoon experiments

    OpenAIRE

    Bhat, GS; Narasimha, R

    2007-01-01

    Eight major field experiments have been carried out so far addressing the Indian summer monsoon. While these experiments were international and the impetus was external till 1980, India’s own monsoon programmes evolved since then. In this article, objectives and outcomes from some of these experiments are described. It is shown that monsoon experiments have contributed in several ways. Each experiment enhanced the infrastructure facilities in the country, brought together scientists from diff...

  20. Adaptive structures flight experiments

    Science.gov (United States)

    Martin, Maurice

    The topics are presented in viewgraph form and include the following: adaptive structures flight experiments; enhanced resolution using active vibration suppression; Advanced Controls Technology Experiment (ACTEX); ACTEX program status; ACTEX-2; ACTEX-2 program status; modular control patch; STRV-1b Cryocooler Vibration Suppression Experiment; STRV-1b program status; Precision Optical Bench Experiment (PROBE); Clementine Spacecraft Configuration; TECHSAT all-composite spacecraft; Inexpensive Structures and Materials Flight Experiment (INFLEX); and INFLEX program status.

  1. The ERASMUS experiment archive

    Science.gov (United States)

    Isakeit, Dieter; Sabbatini, Massimo; Carey, William

    2005-08-01

    The Erasmus Experiment Archive is an electronic database, accessible through the Internet, that collects in a single reference repository scientific, technical and operational information regarding the experiments performed in the experiment facilities which fall under the responsibility of the ESA Directorate of Human Spaceflight, Microgravity and Exploration. The archive is operated, filled with content and kept up-to-date by the Erasmus User Centre. which forms part of the Directorate. The archive shares its records and is interoperable with similar experiment archives of the partner agencies NASA USA) and JAXA (Japan) through a mutually agreed standard for experiment records called the International Distributed Experiment Archive (IDEA).

  2. Experiment WA1 (CDHS Neutrino Experiment)

    CERN Multimedia

    CERN PhotoLab

    1977-01-01

    Experiment WA1, also known under CDHS (CERN, Dortmund, Heidelberg, Saclay; spokesman Jack Steinberger), was the first neutrino experiment on the SPS, in its West Area. Magnetized iron (with a toroidal field) forms the core of the detector. On its outside we see drift chambers and photomultipliers (detecting the light from the plastic scintillators further in). Peter Schilly is wearing a white coat. See also CERN Annual Report 1976, p.57.

  3. Particle physics experiments 1984

    International Nuclear Information System (INIS)

    Stuart, G.

    1985-01-01

    The Rutherford Appleton laboratory report describes work carried out in 1984 on experiments approved by the Particle Physics selection panel. The contents consist of unedited contributions from each experiment. (author)

  4. GARP Atlantic Tropical Experiment

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The GARP Atlantic Tropical Experiment (GATE) was the first major international experiment of the Global Atmospheric Research Program (GARP). It was conducted over...

  5. Social experience infrastructure

    DEFF Research Database (Denmark)

    Kvistgaard, Peter

    2006-01-01

    and explorative fashion to share with others thoughts and ideas concerning the development of new ways to construct/reconstruct recreational spaces with a better coherence with regard to designing experiences. This article claims that it is possible to design recreational spaces with good social experience...... infrastructure in order to create experience spaces for personal experiences (in line with Schultze’s social constructivist view of experiences) without completely adhering to the economic rationalist thoughts and guidelines of Pine & Gilmore that claim that experiences can be designed and controlled...... by experience designers. The notion of social experience infrastructure may be placed in the cross field between the social constructivist and the economic rationalist approach....

  6. Organic chemistry experiment

    International Nuclear Information System (INIS)

    Mun, Seok Sik

    2005-02-01

    This book deals with organic chemistry experiments, it is divided five chapters, which have introduction, the way to write the experiment report and safety in the laboratory, basic experiment technic like recrystallization and extraction, a lot of organic chemistry experiments such as fischer esterification, ester hydrolysis, electrophilic aromatic substitution, aldol reaction, benzoin condensation, wittig reaction grignard reaction, epoxidation reaction and selective reduction. The last chapter introduces chemistry site on the internet and way to find out reference on chemistry.

  7. The Experiment Factory: standardizing behavioral experiments

    Directory of Open Access Journals (Sweden)

    Vanessa V Sochat

    2016-04-01

    Full Text Available The administration of behavioral and experimental paradigms for psychology research is hindered by lack of a coordinated effort to develop and deploy standardized paradigms. While several frameworks (de Leeuw (2015; McDonnell et al. (2012; Mason and Suri (2011; Lange et al. (2015 have provided infrastructure and methods for individual research groups to develop paradigms, missing is a coordinated effort to develop paradigms linked with a system to easily deploy them. This disorganization leads to redundancy in development, divergent implementations of conceptually identical tasks, disorganized and error-prone code lacking documentation, and difficulty in replication. The ongoing reproducibility crisis in psychology and neuroscience research (Baker (2015; Open Science Collaboration (2015 highlights the urgency of this challenge: reproducible research in behavioral psychology is conditional on deployment of equivalent experiments. A large, accessible repository of experiments for researchers to develop collaboratively is most efficiently accomplished through an open source framework. Here we present the Experiment Factory, an open source framework for the development and deployment of web-based experiments. The modular infrastructure includes experiments, virtual machines for local or cloud deployment, and an application to drive these components and provide developers with functions and tools for further extension. We release this infrastructure with a deployment (http://www.expfactory.org that researchers are currently using to run a set of over 80 standardized web-based experiments on Amazon Mechanical Turk. By providing open source tools for both deployment and development, this novel infrastructure holds promise to bring reproducibility to the administration of experiments, and accelerate scientific progress by providing a shared community resource of psychological paradigms.

  8. Designing Urban Experiences

    DEFF Research Database (Denmark)

    Jantzen, Christian; Vetner, Mikael

    2008-01-01

    , and deals with how urban experiences can be designed through careful consideration of how experiences are constituted. Taking the psychological structure of experiences into account when designing urbanity is not only interesting, but also highly relevant as Zuidas is competing with other international...

  9. Virtual neutron scattering experiments

    DEFF Research Database (Denmark)

    Overgaard, Julie Hougaard; Bruun, Jesper; May, Michael

    2016-01-01

    We describe how virtual experiments can be utilized in a learning design that prepares students for hands-on experiments at large-scale facilities. We illustrate the design by showing how virtual experiments are used at the Niels Bohr Institute in a master level course on neutron scattering....... In the last week of the course, students travel to a large-scale neutron scattering facility to perform real neutron scattering experiments. Through student interviews and survey answers, we argue, that the virtual training prepares the students to engage more fruitfully with experiments by letting them focus...

  10. Virtual neutron scattering experiments

    DEFF Research Database (Denmark)

    Overgaard, Julie Hougaard; Bruun, Jesper; May, Michael

    2017-01-01

    We describe how virtual experiments can be utilized in a learning design that prepares students for hands-on experiments at large-scale facilities. We illustrate the design by showing how virtual experiments are used at the Niels Bohr Institute in a master level course on neutron scattering....... In the last week of the course, students travel to a large-scale neutron scattering facility to perform real neutron scattering experiments. Through student interviews and survey answers, we argue, that the virtual training prepares the students to engage more fruitfully with experiments by letting them focus...

  11. Experiments in physical chemistry

    CERN Document Server

    Wilson, J M; Denaro, A R

    1968-01-01

    Experiments in Physical Chemistry, Second Edition provides a compilation of experiments concerning physical chemistry. This book illustrates the link between the theory and practice of physical chemistry. Organized into three parts, this edition begins with an overview of those experiments that generally have a simple theoretical background. Part II contains experiments that are associated with more advanced theory or more developed techniques, or which require a greater degree of experimental skill. Part III consists of experiments that are in the nature of investigations wherein these invest

  12. The Belle II Experiment

    CERN Document Server

    Kahn, J

    2017-01-01

    Set to begin data taking at the end of 2018, the Belle II experiment is the next-generation B-factory experiment hosted at KEK in Tsukuba, Japan. The experiment represents the cumulative effort from the collaboration of experimental and detector physics, computing, and software development. Taking everything learned from the previous Belle experiment, which ran from 1998 to 2010, Belle II aims to probe deeper than ever before into the field of heavy quark physics. By achieving an integrated luminosity of 50 ab−1 and accumulating 50 times more data than the previous experiment across its lifetime, along with a rewritten analysis framework, the Belle II experiment will push the high precision frontier of high energy physics. This paper will give an overview of the key components and development activities that make the Belle II experiment possible.

  13. Diagnostics for pellet experiments

    International Nuclear Information System (INIS)

    Johnson, R.R.

    1978-01-01

    The target diagnostics which are being used and planned in current laser driven ICF Experiments are described. Most of these diagnostics can be easily applied to future ion-beam fusion experiments. The status of laser fusion diagnostics has been much improved in the last 5 years and further improvements can be expected and should be available when the first ICF experiments using ion beams are performed. As an example, x-ray temporal and spatial resolutions are now approximately 5 psec and 3 μm, which is approximately a factor of 4 better than the resolution reported in the first implosion experiments. As one plans ahead for ion-beam fusion experiments it should be emphasized that high yield experiments are easier to diagnose provided adequate shielding is employed. However, in the event that the first high yield experiments fail it will be necessary to have diagnostics available to determine where the problems lie. In laser fusion it is interesting to note that higher laser powers are required now for breakeven experiments than first anticipated, mainly because some aspects of the laser-interaction physics were not recognized until the experiments were carefully diagnosed. Thus as has been pointed out, it may be necessary to increase the energy of the ion-beam driver to enable us to do breakeven experiments with high confidence

  14. Learning and Experience

    DEFF Research Database (Denmark)

    Olesen, Henning Salling

    2017-01-01

    Abstract: This chapter introduces a psycho-societal approach to theorizing learning, combining a materialist theory of socialization with a hermeneutic interpretation methodology. The term "approach" indicates the intrinsic connection between theory, empirical research process and epistemic subject....... Learning is theorized as dynamic subjective experience of (socially situated) realities, counting on individual subjectivity as well as subjective aspects of social interaction. This psycho-societal theory of subjective experiences conceptualizes individual psychic development as interactional experience...... of societal relations, producing an inner psycho-dynamic as a conscious and unconscious individual resource in future life. The symbolization of immediate sensual experiences form an individual life experience of social integration, language use being the medium of collective, social experience (knowledge...

  15. Experiment, right or wrong

    CERN Document Server

    Franklin, Allan

    2008-01-01

    In Experiment, Right or Wrong, Allan Franklin continues his investigation of the history and philosophy of experiment presented in his previous book, The Neglect of Experiment. In this new study, Franklin considers the fallibility and corrigibility of experimental results and presents detailed histories of two such episodes: 1) the experiment and the development of the theory of weak interactions from Fermi's theory in 1934 to the V-A theory of 1957 and 2) atomic parity violation experiments and the Weinberg-Salam unified theory of electroweak interactions of the 1970s and 1980s. In these episodes Franklin demonstrates not only that experimental results can be wrong, but also that theoretical calculations and the comparison between experiment and theory can also be incorrect. In the second episode, Franklin contrasts his view of an "evidence model" of science in which questions of theory choice, confirmation, and refutation are decided on the basis of reliable experimental evidence, with that proposed by the ...

  16. Stimulated Brillouin scattering experiments

    International Nuclear Information System (INIS)

    Slater, D.C.; Berger, R.L.; Busch, G.; Kinzer, C.M.; Mayer, F.J.; Powers, L.V.; Tanner, D.J.

    1981-01-01

    This report describes two experiments in which SBS would be expected to play an important role. In the first experiment, we find a clear signature of the Brillouin backscatter of a short (100 psec) pulse from a long (approx. 50 μm) gradient length gas target plasma. The second experiment used much longer (approx. 1 nsec) pulses on spherical glass shell targets. These experiments were done with both narrow ( 30A) bandwidth laser light. Using one-dimensional, spherically symmetric fluid simulations, we have attempted to model many of the laser-plasma interaction processes which combine to determine the amount of absorbed energy in the long-pulse experiments. These simulations indicate that modest laser bandwidths are successful in reducing the level of SBS at the irradiances ( 15 W/cm 2 ) used in these experiments

  17. Experience composite worth: A combination of experience quality ...

    African Journals Online (AJOL)

    This research suggests that experience quality and experience value be combined into a single multi-dimensional construct, termed experience composite worth. It briefly describes customer experience, experience quality and experience value and the overlap in the dimensions used in outlining experience quality and ...

  18. Linking consumer experiences

    DEFF Research Database (Denmark)

    Smed, Karina Madsen

    become part of the individual self, worldview, and behaviour. This paper seeks to explore links between consumer experiences through the exploration of narrative sequences in travel blogs. Findings indicate that non-consumption is a central element to the bloggers and also indicative of a community......Consumers consume products in various ways serving a number of purposes. Much attention has been paid to experiences attached to consumption, sometimes very explicitly, e.g. in tourism, the essence of which is experiences of various sorts, but often also implicitly as internalised experiences...

  19. Real Life Experiences with Experience Design

    DEFF Research Database (Denmark)

    Dalsgård, Peter; Halskov, Kim

    2006-01-01

    technologies for knowledge dissemination and marketing, in cooperation with public institutions and businesses. We argue that collaborative formulation of core design intentions and values is a valuable instrument in guiding experience design processes, and present three cases from this project, two of which...... resulted in interactive installations. The case installations range from walk-up-and-use consoles, to immersive, responsive, environments based on bodily interaction. We compare the installations, and discuss the interrelations between the resulting interfaces and the intentions for creating...

  20. Experience with MODSIM II

    International Nuclear Information System (INIS)

    Streets, J.; Berg, D.; Oleynik, G.; Pordes, R.; Slimmer, D.

    1992-02-01

    We present results of computer simulations for Data Acquisition systems for large fixed target experiments in an object oriented simulation language, MODSIM. This paper summarizes our experiences and presents preliminary results from the simulation already completed. We also indicate the resources required for this project

  1. Experiments as politics

    NARCIS (Netherlands)

    Spears, R; Smith, HJ

    The purpose of this paper is to illustrate the political nature of laboratory experiments. Such experiments can be construed as paradigms of power, open to construction and debate, where different agents and interests are involved in a process of struggle over both (re)presentation and substance.

  2. Long baseline neutrino experiments

    Indian Academy of Sciences (India)

    High statistics experiment with NNO = 3000/year. Can measure P(νµ → νe). So good sensitivity to θ13 and CP violation but not to matter effects. BNL to Homestake: L = 2540 km, being planned. Ultimate accelerator beam experiment with very high statistics with NNO = 3000/year. Can achieve all the goals listed above with a ...

  3. ATLAS Experiment Brochure - Italian

    CERN Multimedia

    2018-01-01

    ATLAS is one of the four major experiments at the Large Hadron Collider at CERN. It is a general-purpose particle physics experiment run by an international collaboration, and is designed to exploit the full discovery potential and the huge range of physics opportunities that the LHC provides.

  4. ATLAS Experiment Brochure - Serbian

    CERN Multimedia

    2018-01-01

    ATLAS is one of the four major experiments at the Large Hadron Collider at CERN. It is a general-purpose particle physics experiment run by an international collaboration, and is designed to exploit the full discovery potential and the huge range of physics opportunities that the LHC provides.

  5. ATLAS Experiment Brochure

    CERN Multimedia

    AUTHOR|(INSPIRE)INSPIRE-00085461

    2016-01-01

    ATLAS is one of the four major experiments at the Large Hadron Collider at CERN. It is a general-purpose particle physics experiment run by an international collaboration, and is designed to exploit the full discovery potential and the huge range of physics opportunities that the LHC provides.

  6. Realisation, experience, and purification

    DEFF Research Database (Denmark)

    Sobisch, Jan-Ulrich

    2013-01-01

    Often Buddhist mantra practises are portrayed as making and maintaining meditation experiences. Jigten Sumgön explains in his dGongs gcig (5.19) that such a 'making and maintaining' is only a mental fabrication and needs to be purified. Realisation does not arise from experience, but from...

  7. Neutrino oscillation experiments

    International Nuclear Information System (INIS)

    Camilleri, L.

    1996-01-01

    Neutrino oscillation experiments (ν μ →ν e and ν μ →ν τ ) currently being performed at accelerators are reviewed. Future plans for short and long base-line experiments are summarized. (author) 10 figs., 2 tabs., 29 refs

  8. On the Poggendorff Experiment

    Science.gov (United States)

    Coelho, Ricardo Lopes; Silva, P. A. S.; Borges, Paulo de Faria

    2015-01-01

    Poggendorff showed experimentally, in the middle of the 19th century, that the weight of an Atwood machine is reduced when it is brought to motion. His experiment has been revisited from time to time, making use of instrumentation that reflects the technological development of the moment. In this paper, the evolution of the experiment is briefly…

  9. Particle physics experiments 1992

    International Nuclear Information System (INIS)

    Roberts, B.A.

    1993-03-01

    The research programs described here were carried out in 1992 at Rutherford Appleton Laboratory and funded by the United Kingdom Science and Engineering Research Council. The area covered in these experiments is particle physics. Unedited contributions from over forty experimental programs are included. Experiments are listed according to their current status, the accelerator used and its years of operation. (UK)

  10. Ball Collision Experiments

    Science.gov (United States)

    Cross, R.

    2015-01-01

    Experiments are described on collisions between two billiard balls and between a bat and a ball. The experiments are designed to extend a student's understanding of collision events and could be used either as a classroom demonstration or for a student project.

  11. Neutrino oscillation experiments

    Energy Technology Data Exchange (ETDEWEB)

    Camilleri, L. [European Organization for Nuclear Research, Geneva (Switzerland)

    1996-11-01

    Neutrino oscillation experiments ({nu}{sub {mu}}{yields}{nu}{sub e} and {nu}{sub {mu}}{yields}{nu}{sub {tau}}) currently being performed at accelerators are reviewed. Future plans for short and long base-line experiments are summarized. (author) 10 figs., 2 tabs., 29 refs.

  12. Future of neutrino experiments

    Indian Academy of Sciences (India)

    January 2009 physics pp. 109–117. Future of neutrino experiments. TAKAAKI KAJITA. ICRR and IPMU, University of Tokyo, Kashiwa-no-ha 5-1-5, Kashiwa, Chiba 277-8582,. Japan. E-mail: kajita@icrr.u-tokyo.ac.jp. Abstract. Atmospheric, solar, reactor and accelerator neutrino oscillation experiments have measured Δm2.

  13. Human Simulated Diving Experiments.

    Science.gov (United States)

    Bruce, David S.; Speck, Dexter F.

    1979-01-01

    This report details several simulated divinq experiments on the human. These are suitable for undergraduate or graduate laboratories in human or environmental physiology. The experiment demonstrates that a diving reflex is precipitated by both facial cooling and apnea. (Author/RE)

  14. ATLAS Experiment Brochure - French

    CERN Document Server

    2018-01-01

    ATLAS is one of the four major experiments at the Large Hadron Collider at CERN. It is a general-purpose particle physics experiment run by an international collaboration, and is designed to exploit the full discovery potential and the huge range of physics opportunities that the LHC provides.

  15. A Duplicate Construction Experiment.

    Science.gov (United States)

    Bridgeman, Brent

    This experiment was designed to assess the ability of item writers to construct truly parallel tests based on a "duplicate-construction experiment" in which Cronbach argues that if the universe description and sampling are ideally refined, the two independently constructed tests will be entirely equivalent, and that within the limits of item…

  16. Science Experience Unit: Conservation.

    Science.gov (United States)

    Ferguson-Florissant School District, Ferguson, MO.

    GRADES OR AGES: Intermediate grades. SUBJECT MATTER: Conservation. ORGANIZATION AND PHYSICAL APPEARANCE: The guide is divided into 24 experiments. It is mimeographed and staple-bound with a paper cover. OBJECTIVES AND ACTIVITIES: A specific skill or knowledge objective is stated at the beginning of each experiment. Detailed procedures are listed…

  17. Peak Experience Project

    Science.gov (United States)

    Scott, Daniel G.; Evans, Jessica

    2010-01-01

    This paper emerges from the continued analysis of data collected in a series of international studies concerning Childhood Peak Experiences (CPEs) based on developments in understanding peak experiences in Maslow's hierarchy of needs initiated by Dr Edward Hoffman. Bridging from the series of studies, Canadian researchers explore collected…

  18. THX Experiment Overview

    Science.gov (United States)

    Wernet, Mark; Wroblewski, Adam; Locke, Randy; Georgiadis, Nick

    2016-01-01

    This presentation provides an overview of experiments conducted at NASA GRC to provide turbulent flow measurements needed for new turbulence model development and validation. The experiments include particle image velocimetry (PIV) and hot-wire measurements of mean flow velocity and temperature fields, as well as fluctuating components.

  19. Students Experience in Radiography

    International Nuclear Information System (INIS)

    Nyambane, K.D.; Faith Wanjiku Kimunge, W.F.

    2015-01-01

    The Radiography Students from Jomo Kenyatta University of Agriculture and Technology, Kenya share experiences of College Experience, Challenges, Myths and the Radiography dream. The Cultural shock and expectations towards Radiography has changed for the first timers’ students in the radiography class. This has motivated them to remove the fear of the unknown and negatives effects of radiation

  20. Teaching Knowledge Engineering: Experiences

    DEFF Research Database (Denmark)

    Andersen, Tom; Hartvig, Susanne C

    1998-01-01

    Includes description of experiences gained by teaching KE in construction domains. It outlines good starting points and overall guidance to education in applied AI.......Includes description of experiences gained by teaching KE in construction domains. It outlines good starting points and overall guidance to education in applied AI....

  1. Understanding patient experience

    DEFF Research Database (Denmark)

    Andersen, Tariq O.; Andersen, Pernille R. D.; Kornum, Anders C.

    2017-01-01

    , safety) arise from getting feedback on symptoms and from continuous and comforting interaction with clinicians. With this paper, we aim to sensitise UX researchers and designers of patient-centred e-health by proposing three UX dimensions: connectedness, comprehension, and compassion.......The term 'patient experience' is currently part of a global discourse on ways to improve healthcare. This study empirically explores what patient experience is in cardiac remote monitoring and considers the implications for user experience (UX). Through interviews around the deployment of a mobile...... app that enables patients to collaborate with clinicians, we unpack experiences in six themes and present narratives of patients' lifeworlds. We find that patients' emotions are grounded in negative feelings (uncertainty, anxiety, loss of hope) and that positive experiences (relief, reassurance...

  2. Molybdenum solar neutrino experiment

    International Nuclear Information System (INIS)

    Wolfsberg, K.; Cowan, G.A.; Bryant, E.A.

    1984-01-01

    The goal of the molybdenum solar neutrino experiment is to deduce the 8 B solar neutrino flux, averaged over the past several million years, from the concentration of 98 Tc in a deeply buried molybdenum deposit. The experiment is important to an understanding of stellar processes because it will shed light on the reason for the discrepancy between theory and observation of the chlorine solar neutrino experiment. Possible reasons for the discrepancy may lie in the properties of neutrinos (neutrino oscillations or massive neutrinos) or in deficiencies of the standard solar model. The chlorine experiment only measures the 8 B neutrino flux in current times and does not address possible temporal variations in the interior of the sun, which are also not considered in the standard model. In the molybdenum experiment, we plan to measure 98 Tc (4.2 Myr), also produced by 8 B neutrinos, and possibly 97 Tc (2.6 Myr), produced by lower energy neutrinos

  3. Cryogenics for LHC experiments

    CERN Multimedia

    2001-01-01

    Cryogenic systems will be used by LHC experiments to maximize their performance. Institutes around the world are collaborating with CERN in the construction of these very low temperature systems. The cryogenic test facility in hall 180 for ATLAS magnets. High Energy Physics experiments have frequently adopted cryogenic versions of their apparatus to achieve optimal performance, and those for the LHC will be no exception. The two largest experiments for CERN's new flagship accelerator, ATLAS and CMS, will both use large superconducting magnets operated at 4.5 Kelvin - almost 270 degrees below the freezing point of water. ATLAS also includes calorimeters filled with liquid argon at 87 Kelvin. For the magnets, the choice of a cryogenic version was dictated by a combination economy and transparency to emerging particles. For the calorimeters, liquid argon was selected as the fluid best suited to the experiment's physics requirements. High Energy Physics experiments are the result of worldwide collaborations and...

  4. Space Experiment Module (SEM)

    Science.gov (United States)

    Brodell, Charles L.

    1999-01-01

    The Space Experiment Module (SEM) Program is an education initiative sponsored by the National Aeronautics and Space Administration (NASA) Shuttle Small Payloads Project. The program provides nationwide educational access to space for Kindergarten through University level students. The SEM program focuses on the science of zero-gravity and microgravity. Within the program, NASA provides small containers or "modules" for students to fly experiments on the Space Shuttle. The experiments are created, designed, built, and implemented by students with teacher and/or mentor guidance. Student experiment modules are flown in a "carrier" which resides in the cargo bay of the Space Shuttle. The carrier supplies power to, and the means to control and collect data from each experiment.

  5. Undergraduate reactor control experiment

    International Nuclear Information System (INIS)

    Edwards, R.M.; Power, M.A.; Bryan, M.

    1992-01-01

    A sequence of reactor and related experiments has been a central element of a senior-level laboratory course at Pennsylvania State University (Penn State) for more than 20 yr. A new experiment has been developed where the students program and operate a computer controller that manipulates the speed of a secondary control rod to regulate TRIGA reactor power. Elementary feedback control theory is introduced to explain the experiment, which emphasizes the nonlinear aspect of reactor control where power level changes are equivalent to a change in control loop gain. Digital control of nuclear reactors has become more visible at Penn State with the replacement of the original analog-based TRIGA reactor control console with a modern computer-based digital control console. Several TRIGA reactor dynamics experiments, which comprise half of the three-credit laboratory course, lead to the control experiment finale: (a) digital simulation, (b) control rod calibration, (c) reactor pulsing, (d) reactivity oscillator, and (e) reactor noise

  6. Simulation - modeling - experiment; Simulation - modelisation - experience

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    After two workshops held in 2001 on the same topics, and in order to make a status of the advances in the domain of simulation and measurements, the main goals proposed for this workshop are: the presentation of the state-of-the-art of tools, methods and experiments in the domains of interest of the Gedepeon research group, the exchange of information about the possibilities of use of computer codes and facilities, about the understanding of physical and chemical phenomena, and about development and experiment needs. This document gathers 18 presentations (slides) among the 19 given at this workshop and dealing with: the deterministic and stochastic codes in reactor physics (Rimpault G.); MURE: an evolution code coupled with MCNP (Meplan O.); neutronic calculation of future reactors at EdF (Lecarpentier D.); advance status of the MCNP/TRIO-U neutronic/thermal-hydraulics coupling (Nuttin A.); the FLICA4/TRIPOLI4 thermal-hydraulics/neutronics coupling (Aniel S.); methods of disturbances and sensitivity analysis of nuclear data in reactor physics, application to VENUS-2 experimental reactor (Bidaud A.); modeling for the reliability improvement of an ADS accelerator (Biarotte J.L.); residual gas compensation of the space charge of intense beams (Ben Ismail A.); experimental determination and numerical modeling of phase equilibrium diagrams of interest in nuclear applications (Gachon J.C.); modeling of irradiation effects (Barbu A.); elastic limit and irradiation damage in Fe-Cr alloys: simulation and experiment (Pontikis V.); experimental measurements of spallation residues, comparison with Monte-Carlo simulation codes (Fallot M.); the spallation target-reactor coupling (Rimpault G.); tools and data (Grouiller J.P.); models in high energy transport codes: status and perspective (Leray S.); other ways of investigation for spallation (Audoin L.); neutrons and light particles production at intermediate energies (20-200 MeV) with iron, lead and uranium targets (Le Colley F

  7. Understanding customer experience.

    Science.gov (United States)

    Meyer, Christopher; Schwager, Andre

    2007-02-01

    Anyone who has signed up for cell phone service, attempted to claim a rebate, or navigated a call center has probably suffered from a company's apparent indifference to what should be its first concern: the customer experiences that culminate in either satisfaction or disappointment and defection. Customer experience is the subjective response customers have to direct or indirect contact with a company. It encompasses every aspect of an offering: customer care, advertising, packaging, features, ease of use, reliability. Customer experience is shaped by customers' expectations, which largely reflect previous experiences. Few CEOs would argue against the significance of customer experience or against measuring and analyzing it. But many don't appreciate how those activities differ from CRM or just how illuminating the data can be. For instance, the majority of the companies in a recent survey believed they have been providing "superior" experiences to customers, but most customers disagreed. The authors describe a customer experience management (CEM) process that involves three kinds of monitoring: past patterns (evaluating completed transactions), present patterns (tracking current relationships), and potential patterns (conducting inquiries in the hope of unveiling future opportunities). Data are collected at or about touch points through such methods as surveys, interviews, focus groups, and online forums. Companies need to involve every function in the effort, not just a single customer-facing group. The authors go on to illustrate how a cross-functional CEM system is created. With such a system, companies can discover which customers are prospects for growth and which require immediate intervention.

  8. DT experiment on JET

    International Nuclear Information System (INIS)

    Itoh, Sanae; Itoh, Kimitaka

    1992-01-01

    In November, 1991, at the JET tokamak in Abingdon, the U.K., DT plasma combustion experiment was carried out for the first time in history. The output power by nuclear fusion of 1.7 MW at maximum and the total power output of 2 MJ were attained, and it was proved that the controlled nuclear fusion accompanied by considerable power output can be carried out on the ground as a real thing. One milestone of the dream and target of nuclear fusion reactors was attained. In this paper, the results of the experiment are reported, and their meaning for the research of hereafter is considered. In the experiment this time, 0.24 g of tritium in total was used, including conditioning. The last two shots became the power output experiment of MW class nuclear fusion reaction, in which about 13% of tritium fuel ratio was estimated. The preliminary tritium experiment was divided into six phases, and was carried out for three weeks, aiming at collecting the basic data for the full scale DT experiment. The examination of the research program, the preliminary tritium experiment and the success of the PTE and the new development are described. (K.I.)

  9. Conducting interactive experiments online.

    Science.gov (United States)

    Arechar, Antonio A; Gächter, Simon; Molleman, Lucas

    2018-01-01

    Online labor markets provide new opportunities for behavioral research, but conducting economic experiments online raises important methodological challenges. This particularly holds for interactive designs. In this paper, we provide a methodological discussion of the similarities and differences between interactive experiments conducted in the laboratory and online. To this end, we conduct a repeated public goods experiment with and without punishment using samples from the laboratory and the online platform Amazon Mechanical Turk. We chose to replicate this experiment because it is long and logistically complex. It therefore provides a good case study for discussing the methodological and practical challenges of online interactive experimentation. We find that basic behavioral patterns of cooperation and punishment in the laboratory are replicable online. The most important challenge of online interactive experiments is participant dropout. We discuss measures for reducing dropout and show that, for our case study, dropouts are exogenous to the experiment. We conclude that data quality for interactive experiments via the Internet is adequate and reliable, making online interactive experimentation a potentially valuable complement to laboratory studies.

  10. Temporal Experience and Metaphysics

    Directory of Open Access Journals (Sweden)

    Graham Peebles

    Full Text Available ABSTRACT The well-known phenomenological argument draws metaphysical conclusions about time, specifically about change through time and the resulting passage or flow of time, from our temporal experience. The argument begins with the phenomenological premise that there is a class of properties which underlies our experience of time and change through time, and its conclusion is that these properties are not merely experienced but exemplified. I argue that the phenomenological argument is best served by the adoption of a representational theory of perception. I then present a representational theory of temporal experience.

  11. The Experiment as Act

    DEFF Research Database (Denmark)

    Søndergaard, Morten

    to identify and locate the experiments of POEX65 as acts; and to ask the questions: what constitutes those acts as experiments? and how do we possibly archive them? My purpose, then, is to define the methodologies to obtain the contours of a post-phenomenology of experimental artistic production in order...... to be able to analyse the phenomena found at POEX65. Here I will use the notion of the ‘ontological theatre’ (Pickering), which, according to Pickering, is acted out in experimental art productions. The experiment could thus be seen as an ‘agency-realism’ – as an ‘act’ of relations across the aesthetics...

  12. Making the Experience City

    DEFF Research Database (Denmark)

    Jensen, Ole B.

    2009-01-01

    This paper describes the latest research into cultural planning and architectural branding in Denmark based on the ‘Experience City' research project located at Aalborg University. The paper explores the implication of the turn towards culture and experience in the contemporary Danish city. It thus...... makes an investigation into the complex relationship between the words and policies of the ‘Experience Economy' and the actual urban transformations made in cities with reference to these changes. The paper discusses the cases researched in relation to the state, market, civil society framework as well...

  13. Experimenting for resilience

    DEFF Research Database (Denmark)

    Hagedorn-Rasmussen, Peter; Dupret, Katia

    Focusing on how an experimental approach to organizing may pave the way for organizational resilience, we explore opportunities and barriers of experimental organizing by following a concrete social experiment in civil society and discuss its adaptability in traditional organizations. The social...... experiment is called Civic Desire. The founders explicitly call for new ways of organizing that can develop social sustainability. We discuss how these experiments may create platforms of new unforeseen goals that organizations may choose to follow. In conclusion we argue for organizational resilience...

  14. Nightshade Prototype Experiments (Silverleaf)

    Energy Technology Data Exchange (ETDEWEB)

    Danielson, Jeremy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bauer, Amy L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-12-23

    The Red Sage campaign is a series of subcritical dynamic plutonium experiments designed to measure ejecta. Nightshade, the first experiments in Red Sage scheduled for fiscal year 2019, will measure the amount of ejecta emission into vacuum from a double-­shocked plutonium surface. To address the major technical risks in Nightshade, a Level 2 milestone was developed for fiscal year 2016. Silverleaf, a series of four experiments, was executed at the Los Alamos National Laboratory in July and August 2016 to demonstrate a prototype of the Nightshade package and to satisfy this Level 2 milestone. This report is documentation that Red Sage Level 2 milestone requirements were successfully met.

  15. CANDU operating experience

    International Nuclear Information System (INIS)

    McConnell, L.G.; Woodhead, L.W.; Fanjoy, G.R.; Thurygill, E.W.

    1980-05-01

    The CANDU-PHW program is based upon 38 years of heavy water reactor experience with 35 years of operating experience. Canada has had 72 reactor years of nuclear-electric operations experience with 10 nuclear units in 4 generating stations during a period of 18 years. All objectives have been met with outstanding performance: worker safety, public safety, environmental emissions, reliable electricity production, and low electricity cost. The achievement has been realized through total teamwork involving all scientific disciplines and all project functions (research, design, manufacturing, construction, and operation). (auth)

  16. Game user experience evaluation

    CERN Document Server

    Bernhaupt, Regina

    2015-01-01

    Evaluating interactive systems for their user experience (UX) is a standard approach in industry and research today. This book explores the areas of game design and development and Human Computer Interaction (HCI) as ways to understand the various contributing aspects of the overall gaming experience. Fully updated, extended and revised this book is based upon the original publication Evaluating User Experience in Games, and provides updated methods and approaches ranging from user- orientated methods to game specific approaches. New and emerging methods and areas explored include physiologi

  17. General relativity and experiment

    OpenAIRE

    Damour, T.

    1994-01-01

    The confrontation between Einstein's theory of gravitation and experiment is summarized. Although all current experimental data are compatible with general relativity, the importance of pursuing the quest for possible deviations from Einstein's theory is emphasized.

  18. Lidar calibration experiments

    DEFF Research Database (Denmark)

    Ejsing Jørgensen, Hans; Mikkelsen, T.; Streicher, J.

    1997-01-01

    A series of atmospheric aerosol diffusion experiments combined with lidar detection was conducted to evaluate and calibrate an existing retrieval algorithm for aerosol backscatter lidar systems. The calibration experiments made use of two (almost) identical mini-lidar systems for aerosol cloud...... detection to test the reproducibility and uncertainty of lidars. Lidar data were obtained from both single-ended and double-ended Lidar configurations. A backstop was introduced in one of the experiments and a new method was developed where information obtained from the backstop can be used in the inversion...... algorithm. Independent in-situ aerosol plume concentrations were obtained from a simultaneous tracer gas experiment with SF6, and comparisons with the two lidars were made. The study shows that the reproducibility of the lidars is within 15%, including measurements from both sides of a plume...

  19. Muon ionization cooling experiment

    CERN Multimedia

    CERN. Geneva

    2003-01-01

    A neutrino factory based on a muon storage ring is the ultimate tool for studies of neutrino oscillations, including possibly leptonic CP violation. It is also the first step towards muon colliders. The performance of this new and promising line of accelerators relies heavily on the concept of ionisation cooling of minimum ionising muons, for which much R&D is required. The concept of a muon ionisation cooling experiment has been extensively studied and first steps are now being taken towards its realisation by a joint international team of accelerator and particle physicists. The aim of the workshop is to to explore at least two versions of an experiment based on existing cooling channel designs. If such an experiment is feasible, one shall then select, on the basis of effectiveness, simplicity, availability of components and overall cost, a design for the proposed experiment, and assemble the elements necessary to the presentation of a proposal. Please see workshop website.

  20. LADEE LUNAR DUST EXPERIMENT

    Data.gov (United States)

    National Aeronautics and Space Administration — This archive bundle includes data taken by the Lunar Dust Experiment (LDEX) instrument aboard the Lunar Atmosphere and Dust Environment Explorer (LADEE) spacecraft....

  1. Experiments on Tape

    Science.gov (United States)

    Whitfield, Eddie

    1976-01-01

    The use of science experiments on tape are shown to provide for individual differences from the gifted child to the handicapped in developing skills in the languare art area, developing significant concepts, and making learning come alive. (EB)

  2. Experiments with needle bearings

    Science.gov (United States)

    Ferretti, Pericle

    1933-01-01

    Experiments and results are presented in testing needle bearings, especially in comparison with roller bearings. Reduction in coefficient of friction is discussed as well as experimental methods and recording devices.

  3. The experiments ALICE

    CERN Document Server

    Fabjan, Christian

    2009-01-01

    This article documents the main design choices and the close to 20 years of preparation, detector R&D, construction and installation of ALICE, the dedicated heavy ion experiment at the CERN LHC accelerator.

  4. Experience Communication and Aesthetics

    DEFF Research Database (Denmark)

    Thorlacius, Lisbeth

    to user aspect (web 2.0), the personal engagement or the community spirit. This increasing demand of experiences reflects the postmodern cultural trends where rules for how to think and behave no longer exist. This results in individualism, where the identity of the human being has changed from something...... are produced within the field of experience communication. Aesthetical experiences may be a product of the concept of novelty, the unpredictable, the inexpressible, the making of identity, the self-actualization, the self-staging, the interactive aspect, the co-producer role (the prosumer role), the user...... challenge in terms of creating experience based communication designs which meet the need of self-actualization and creation of own identities of the target audiences.  ...

  5. The Northfield experiments.

    Science.gov (United States)

    Harrison, T; Clarke, D

    1992-05-01

    The Northfield Experiments took place at Hollymoor Hospital, Northfield, Birmingham, during World War II. The first experiment was conducted by Bion & Rickman. The second evolved gradually; many people contributed to its success, including Foulkes, Main and Bridger. The experiments were an important landmark in the evolution of theory and practice in group psychotherapy and in the therapeutic community movement. They were not carried out solely as responses to the need for mass treatment of neurotic disorders among army personnel; antecedent factors, the theoretical orientation of the practitioners and the nature of army life were equally important. The two experiments differed in pace and in recognition of the needs of higher-order systems, particularly the military hierarchy. They shared many underlying concepts, including responsibility to society, the therapeutic use of groups (including the hospital community) and an emphasis on process. Lessons learned at Northfield remain relevant to the practice of psychiatry today.

  6. User Experience Dimensions

    DEFF Research Database (Denmark)

    Lykke, Marianne; Jantzen, Christian

    2016-01-01

    The present study develops a set of 10 dimensions based on a systematic understanding of the concept of experience as a holistic psychological. Seven of these are derived from a psychological conception of what experiencing and experiences are. Three supplementary dimensions spring from...... the observation that experiences apparently have become especially valuable phenomena in Western societies. The 10 dimensions are tried out in a field study at the Center for Art and Media (ZKM) in Germany with the purpose to study their applicability in the evaluation of interactive sound archives. 29 walk......-alongs were carried out with 58 museums visitors. Our analysis showed that it was possible to identify the 10 experience dimensions in the study material. Some dimensions were expressed more frequently than others. The distribution of expressed dimensions and the content of the user comments provided a clear...

  7. The world's biggest experiment

    CERN Multimedia

    Gregson, Liz

    2008-01-01

    According to CERN, our understanding of the Universe is about the change. Meet the Imperial alumni and staff who are involved in CERN's Large Hadron Collider, the world's biggest experiment. (3 pages)

  8. The Brain Experiment

    Science.gov (United States)

    Polenta, G.; Calvo, M.; Conversi, L.; de Bernardis, P.; Giordano, C.; Iacoangeli, A.; Maiello, M.; Marini-Bettolo, C.; Masi, S.; Nati, F.; Nati, L.; Peterzen, S.; Piacentini, F.; Sordini, R.; Veneziani, M.; Bartlett, J.; Bréelle, E.; Dufour, C.; Galli, S.; Ganga, K.; Ghribi, A.; Giraud-Heraud, Y.; Guglielmi, L.; Hamilton, J. C.; Kaplan, J.; Piat, M.; Gervasi, M.; Sironi, G.; Spinelli, S.; Tartari, A.; Zannoni, M.; Maffei, B.; Piccirillo, L.; Pisano, G.; Ade, P.; Orlando, A.; Savini, G.; Brossard, J.; Giard, M.; Landé, J.; Bergé, L.; Dumoulin, L.; Juillard, A.; Marnieros, S.; Pajot, F.; Rosset, C.

    2008-09-01

    The rotational component of the CMB polarization, the so-called B-modes, is one of the major topic for next generation CMB experiments. This signal traces the effect on the CMB due to primordial gravitational waves produced during the inflationary epoch, probing the physics of the very early universe at GUT energy scales. This is a challenge, being the expected amplitude of B-mode polarization ~ 0.1μK. In this paper we describe the BRAIN experiment, a bolometric interferometer which combines high sensitivity bolometric detectors with the excellent control of systematic effects proper of interferometers. Being a ground based experiment, we identified Dome Charlie in Antarctica as the best site for such measurements. In order to validate the goodness of the site, as well as some of the implemented technical solutions, we built a pathfinder experiment which has been successfully operated during last Antarctic summer, and we report about preliminary results obtained.

  9. Experiments in Animal Behavior

    Science.gov (United States)

    Polt, James M.

    1971-01-01

    Describes experiments in conditioning, sensory processes, social behavior, imprinting, innate preferences for color and form, and discrimination learning suitable for secondary school students. Mealworms, crickets, and chicks are used as subjects. (AL)

  10. Stimulation and reservoir engineering of geothermal resources. Second annual report, July 1, 1978-September 30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Kruger, P.; Ramey, H.J. Jr.

    1979-09-01

    Individual projects are grouped under four main areas of study: energy extraction, bench-scale flow experiments, radon tracer techniques, and well test analysis. The energy extraction experiments concern the efficiency with which the in-place heat and fluids can be produced in the most economical manner. The bench-scale flow experiments cover the results of three models used to examine the properties of flow through porous media at elevated temperature and pressures. Random tracer techniques describe accelerated efforts to field test several geothermal reservoirs by both transient and transect test procedures. The well test analysis section describes several new developments: analysis of earth-tide effects, pressure transient analysis of multilayered systems, interference testing with storage and skin effects, determination of steam-water relative permeability from wellhead data, well test analysis for wells produced at constant pressure, the parallelepiped model, slug test DST analysis, and pressure transient behavior in naturally fractured reservoirs. (MHR)

  11. Experiment-o-mania

    Science.gov (United States)

    Drndarski, Marina

    2015-04-01

    Every 21st century student is expected to develop science literacy skills. As this is not part of Serbian national curriculum yet, we decided to introduce it with this project. Experiment-o-mania provides students to experience science in different and exciting way. It makes opportunity for personalized learning offering space and time to ask (why, where, how, what if) and to try. Therefore, we empower young people with skills of experimenting, and they love science back. They ask questions, make hypothesis, make problems and solve them, make mistakes, discuss about the results. Subsequently this raises the students' interest for school curriculum. This vision of science teaching is associated with inquiry-based learning. Experiment-o-mania is the unique and recognizable teaching methodology for the elementary school Drinka Pavlović, Belgrade, Serbia. Experiment-o-mania implies activities throughout the school year. They are held on extra class sessions, through science experiments, science projects or preparations for School's Days of science. Students learn to ask questions, make observations, classify data, communicate ideas, conduct experiments, analyse results and make conclusions. All science teachers participate in designing activities and experiments for students in Experiment-o-mania teaching method. But they are not alone. Teacher of fine arts, English teachers and others also take part. Students have their representatives in this team, too. This is a good way to blend knowledge among different school subject and popularize science in general. All the experiments are age appropriate and related to real life situations, local community, society and the world. We explore Fibonacci's arrays, saving energy, solar power, climate change, environmental problems, pollution, daily life situations in the country or worldwide. We introduce great scientists as Nikola Tesla, Milutin Milanković and sir Isaac Newton. We celebrate all relevant international days, weeks

  12. The MAJORANA Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Aguayo Navarrete, Estanislao; Avignone, F. T.; Back, Henning O.; Barabash, Alexander S.; Bergevin, M.; Bertrand, F.; Boswell, M.; Brudanin, V.; Busch, Matthew; Chan, Yuen-Dat; Christofferson, Cabot-Ann; Collar, J. I.; Combs, Dustin C.; Cooper, R. J.; Detwiler, Jason A.; Doe, Peter J.; Efremenko, Yuri; Egorov, Viatcheslav; Ejiri, H.; Elliott, Steven R.; Esterline, James H.; Fast, James E.; Fields, N.; Finnerty, P.; Fraenkle, Florian; Gehman, Victor M.; Giovanetti, G. K.; Green, Matthew P.; Guiseppe, Vincente; Gusey, K.; Hallin, A. L.; Hazama, R.; Henning, R.; Hime, Andrew; Hoppe, Eric W.; Horton, Mark; Howard, Stanley; Howe, M. A.; Johnson, R. A.; Keeter, K.; Keillor, Martin E.; Keller, C.; Kephart, Jeremy D.; Kidd, Mary; Knecht, A.; Kochetov, Oleg; Konovalov, S.; Kouzes, Richard T.; LaFerriere, Brian D.; LaRoque, B. H.; Leon, Jonathan D.; Leviner, L.; Loach, J. C.; MacMullin, S.; Marino, Michael G.; Martin, R. D.; Mei, Dong-Ming; Merriman, Jason H.; Miller, M. L.; Mizouni, Leila; Nomachi, Masaharu; Orrell, John L.; Overman, Nicole R.; Phillips, D.; Poon, Alan; Perumpilly, Gopakumar; Prior, Gersende; Radford, D. C.; Rielage, Keith; Robertson, R. G. H.; Ronquest, M. C.; Schubert, Alexis G.; Shima, T.; Shirchenko, M.; Snavely, Kyle J.; Sobolev, V.; Steele, David; Strain, J.; Thomas, K.; Timkin, V.; Tornow, W.; Vanyushin, I.; Varner, R. L.; Vetter, Kai; Vorren, Kris R.; Wilkerson, John; Wolfe, B. A.; Yakushev, E.; Young, A.; Yu, Chang-Hong; Yumatov, Vladimir; Zhang, C.

    2011-10-01

    The Majorana collaboration is actively pursuing research and development aimed at a tonne-scale {sup 76}Ge neutrinoless double-beta decay ({beta}{beta}(0{nu})-decay) experiment. The current, primary focus is the construction of the Majorana Demonstrator experiment, an R and D effort that will field approximately 40 kg of germanium detectors with mixed enrichment levels. This article provides a status update on the construction of the Demonstrator.

  13. Particle physics experiments 1980

    International Nuclear Information System (INIS)

    Rousseau, M.D.; Stuart, G.

    1981-01-01

    This report describes work carried out in 1980 on experiments approved by the Particle Physics Ezperiments Selection Panel. A table of contents giving, title and collaboration, technique, accelerator used, year of running, status as at December 1980, the spokesman and experimental code, is followed by unedited contributions from each of the 54 experiments included in this annual review including lists of submitted publications. (U.K.)

  14. The CLOUD experiment

    CERN Multimedia

    Maximilien Brice

    2006-01-01

    The Cosmics Leaving Outdoor Droplets (CLOUD) experiment as shown by Jasper Kirkby (spokesperson). Kirkby shows a sketch to illustrate the possible link between galactic cosmic rays and cloud formations. The CLOUD experiment uses beams from the PS accelerator at CERN to simulate the effect of cosmic rays on cloud formations in the Earth's atmosphere. It is thought that cosmic ray intensity is linked to the amount of low cloud cover due to the formation of aerosols, which induce condensation.

  15. The MAJORANA Experiment

    International Nuclear Information System (INIS)

    Aguayo Navarrete, Estanislao; Avignone, F.T.; Back, Henning O.; Barabash, Alexander S.; Bergevin, M.; Bertrand, F.; Boswell, M.; Brudanin, V.; Busch, Matthew; Chan, Yuen-Dat; Christofferson, Cabot-Ann; Collar, J.I.; Combs, Dustin C.; Cooper, R.J.; Detwiler, Jason A.; Doe, Peter J.; Efremenko, Yuri; Egorov, Viatcheslav; Ejiri, H.; Elliott, Steven R.; Esterline, James H.; Fast, James E.; Fields, N.; Finnerty, P.; Fraenkle, Florian; Gehman, Victor M.; Giovanetti, G.K.; Green, Matthew P.; Guiseppe, Vincente; Gusey, K.; Hallin, A.L.; Hazama, R.; Henning, R.; Hime, Andrew; Hoppe, Eric W.; Horton, Mark; Howard, Stanley; Howe, M.A.; Johnson, R.A.; Keeter, K.; Keillor, Martin E.; Keller, C.; Kephart, Jeremy D.; Kidd, Mary; Knecht, A.; Kochetov, Oleg; Konovalov, S.; Kouzes, Richard T.; LaFerriere, Brian D.; LaRoque, B.H.; Leon, Jonathan D.; Leviner, L.; Loach, J.C.; MacMullin, S.; Marino, Michael G.; Martin, R.D.; Mei, Dong-Ming; Merriman, Jason H.; Miller, M.L.; Mizouni, Leila; Nomachi, Masaharu; Orrell, John L.; Overman, Nicole R.; Phillips, D.; Poon, Alan; Perumpilly, Gopakumar; Prior, Gersende; Radford, D.C.; Rielage, Keith; Robertson, R.G.H.; Ronquest, M.C.; Schubert, Alexis G.; Shima, T.; Shirchenko, M.; Snavely, Kyle J.; Sobolev, V.; Steele, David; Strain, J.; Thomas, K.; Timkin, V.; Tornow, W.; Vanyushin, I.; Varner, R.L.; Vetter, Kai; Vorren, Kris R.; Wilkerson, John; Wolfe, B.A.; Yakushev, E.; Young, A.; Yu, Chang-Hong; Yumatov, Vladimir; Zhang, C.

    2011-01-01

    The Majorana collaboration is actively pursuing research and development aimed at a tonne-scale 76 Ge neutrinoless double-beta decay (ββ(0ν)-decay) experiment. The current, primary focus is the construction of the Majorana Demonstrator experiment, an R and D effort that will field approximately 40 kg of germanium detectors with mixed enrichment levels. This article provides a status update on the construction of the Demonstrator.

  16. Digital Heritage Experiences

    DEFF Research Database (Denmark)

    Munar, Ana Maria; Ooi, Can-Seng

    The evolution of the Web and the expansion of social media are transforming our heritage experiences. Social media offer an innovative element to personal travel reflections by providing digital global platforms on which tourists can create and publish their travel stories. Social media transform...... the traditional creative processes, distribution mechanisms and consumption patterns of these experiences. This study provides insight on how personal heritage moments are constructed, digitalized and shared. The methodological perspective adopted draws on a constructivist epistemology (Markham 2004...

  17. The LHCb experiment

    CERN Document Server

    Nakada, Tatsuya

    2000-01-01

    The LHCb experiment is designed to fully exploit the large number of b hadrons expected at the LHC energy and luminosity. The experiment is equipped with particle identification devices and can efficiently trigger events with different B-meson final states, allowing systematic studies of CP violation and other rare phenomena in the b hadron system with a high precision which could reveal physics beyond the standard model.

  18. Impact of compost process conditions on organic micro pollutant degradation during full scale composting.

    Science.gov (United States)

    Sadef, Yumna; Poulsen, Tjalfe Gorm; Bester, Kai

    2015-06-01

    Knowledge about the effects of oxygen concentration, nutrient availability and moisture content on removal of organic micro-pollutants during aerobic composting is at present very limited. Impact of oxygen concentration, readily available nitrogen content (NH4(+), NO3(-)), and moisture content on biological transformation of 15 key organic micro-pollutants during composting, was therefore investigated using bench-scale degradation experiments based on non-sterile compost samples, collected at full-scale composting facilities. In addition, the adequacy of bench-scale composting experiments for representing full-scale composting conditions, was investigated using micro-pollutant concentration measurements from both bench- and full-scale composting experiments. Results showed that lack of oxygen generally prevented transformation of organic micro-pollutants. Increasing readily available nitrogen content from about 50 mg N per 100 g compost to about 140 mg N per 100 g compost actually reduced micro-pollutant transformation, while changes in compost moisture content from 50% to 20% by weight, only had minor influence on micro-pollutant transformation. First-order micro-pollutant degradation rates for 13 organic micro-pollutants were calculated using data from both full- and bench-scale experiments. First-order degradation coefficients for both types of experiments were similar and ranged from 0.02 to 0.03 d(-1) on average, indicating that if a proper sampling strategy is employed, bench-scale experiments can be used to represent full-scale composting conditions. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Experiments in computing: a survey.

    Science.gov (United States)

    Tedre, Matti; Moisseinen, Nella

    2014-01-01

    Experiments play a central role in science. The role of experiments in computing is, however, unclear. Questions about the relevance of experiments in computing attracted little attention until the 1980s. As the discipline then saw a push towards experimental computer science, a variety of technically, theoretically, and empirically oriented views on experiments emerged. As a consequence of those debates, today's computing fields use experiments and experiment terminology in a variety of ways. This paper analyzes experimentation debates in computing. It presents five ways in which debaters have conceptualized experiments in computing: feasibility experiment, trial experiment, field experiment, comparison experiment, and controlled experiment. This paper has three aims: to clarify experiment terminology in computing; to contribute to disciplinary self-understanding of computing; and, due to computing's centrality in other fields, to promote understanding of experiments in modern science in general.

  20. Qualitative experiments in psychology

    DEFF Research Database (Denmark)

    Wagoner, Brady

    2015-01-01

    In this article, I explore the meaning of experiments in early twentieth century psychology, focusing on the qualitative experimental methodology of psychologist Frederic BARTLETT. I begin by contextualizing BARTLETT's experiments within the continental research tradition of his time, which...... was in a state of transition from a focus on elements (the concern of psychophysics) to a focus on wholes (the concern of Gestalt psychology). The defining feature of BARTLETT's early experiments is his holistic treatment of human responses, in which the basic unit of analysis is the active person relating...... to some material within the constraints of a social and material context. This manifests itself in a number of methodological principles that contrast with contemporary understandings of experimentation in psychology. The contrast is further explored by reviewing the history of "replications...

  1. The BLAST experiment

    International Nuclear Information System (INIS)

    Hasell, D.; Akdogan, T.; Alarcon, R.; Bertozzi, W.; Booth, E.; Botto, T.; Calarco, J.R.; Clasie, B.; Crawford, C.; DeGrush, A.; Dow, K.; Dutta, D.; Farkhondeh, M.; Fatemi, R.; Filoti, O.; Franklin, W.; Gao, H.; Geis, E.; Gilad, S.; Hersman, W.

    2009-01-01

    The Bates large acceptance spectrometer toroid (BLAST) experiment was operated at the MIT-Bates Linear Accelerator Center from 2003 until 2005. The detector and experimental program were designed to study, in a systematic manner, the spin-dependent electromagnetic interaction in few-nucleon systems. As such the data will provide improved measurements for neutron, proton, and deuteron form factors. The data will also allow details of the reaction mechanism, such as the role of final state interactions, pion production, and resonances to be studied. The experiment used: a longitudinally polarized electron beam stored in the South Hall Storage Ring; a highly polarized, isotopically pure, internal gas target of hydrogen or deuterium provided by an atomic beam source; and a symmetric, general purpose detector based on a toroidal spectrometer with tracking, time-of-flight, Cherenkov, and neutron detectors. Details of the experiment and operation are presented.

  2. Experiences of depression

    DEFF Research Database (Denmark)

    Rønberg, Mette

    In this thesis, I examine the complex experiences of what we call depression in everyday life, the multifaceted and ambiguous experiences of getting a depression diagnosis, and the in-depth processes involved in learning to live under the description of depression. The thesis is based...... on ethnographic fieldwork among adults diagnosed with depression in Denmark, and consists of three articles that provide glimpses into experiences of depression and diagnostic processes. The articles deal with creativity, variability and resistance in diagnostic processes and illustrates how these not are once......-and-for-all-dealt-with matters but rather messy and complicated processes, that involve several actors and multiple relations to the diagnosis. The thesis furthermore challenges the dominant diagnostic understanding depression as a neurobiological, and individual disorder in present-day diagnostic cultures, by arguing...

  3. Experiments in mixed reality

    Science.gov (United States)

    Krum, David M.; Sadek, Ramy; Kohli, Luv; Olson, Logan; Bolas, Mark

    2010-01-01

    As part of the Institute for Creative Technologies and the School of Cinematic Arts at the University of Southern California, the Mixed Reality lab develops technologies and techniques for presenting realistic immersive training experiences. Such experiences typically place users within a complex ecology of social actors, physical objects, and collections of intents, motivations, relationships, and other psychological constructs. Currently, it remains infeasible to completely synthesize the interactivity and sensory signatures of such ecologies. For this reason, the lab advocates mixed reality methods for training and conducts experiments exploring such methods. Currently, the lab focuses on understanding and exploiting the elasticity of human perception with respect to representational differences between real and virtual environments. This paper presents an overview of three projects: techniques for redirected walking, displays for the representation of virtual humans, and audio processing to increase stress.

  4. The Dialogue of Experience

    DEFF Research Database (Denmark)

    Jørgensen, Dorthe

    2016-01-01

    In “The Dialogue of Experience,” Dorthe Jørgensen presents Gianni Vattimo’s understanding, expressed in his The Responsibility of the Philosopher, of what it means to be a philosopher. According to Jørgensen, Vattimo’s work as a philosopher is an example of ‘world-engaged philosophy’ as distinct...... from ‘school philosophy’ or ‘applied philosophy.’ The concept of ‘world-engaged philosophy’ is associated with Jørgensen’s concept of ‘world poetry’: that the immanent world is ambiguous; it occasions experiences of a surplus of meaning, traditionally called beauty. Furthermore, both concepts...... are associated with her concept of ‘basic experience’ and with her understanding of it as characterized by an immanent ‘dialogue’ between sensation, faith, and comprehension. According to Jørgensen, all experiences are rooted in sensation, faith, and comprehension; art, religion, and thought, or aesthetics...

  5. Magnetic scattering experiments

    International Nuclear Information System (INIS)

    Vettier, C.

    2001-01-01

    We discuss the relative use of neutrons and X-rays as scattering tools to probe the magnetic properties of materials. Neutron diffraction experiments continue to be the most appropriate tool to determine the magnetic structure of bulk solids. Synchrotron X-ray experiments are and will be used to investigate selectively the magnetic behaviour of different chemical species and/or electronic shells in magnetic systems. There exist some grey areas where the two probes can be used depending on the scientific problem under investigation. In particular, neutrons allow very accurate measurements of magnetic form factors, but X-rays provide a separation of the orbital momentum contribution to magnetisation. Comparisons between X-rays and neutrons studies of magnetism at surfaces are presented. Finally, one can anticipate that only inelastic neutron scattering experiments will allow the observation of magnetic excitations across the whole Brillouin zone

  6. Operating experience feedback

    International Nuclear Information System (INIS)

    Cimesa, S.

    2007-01-01

    Slovenian Nuclear Safety Administration (SNSA) has developed its own system for tracking, screening and evaluating the operating experiences of the nuclear installations. The SNSA staff regularly tracks the operating experiences throughout the world and screens them on the bases of applicability for the Slovenian nuclear facilities. The operating experiences, which pass the screening, are thoroughly evaluated and also recent operational events in these facilities are taken into account. If needed, more information is gathered to evaluate the conditions of the Slovenian facilities and appropriate corrective actions are considered. The result might be the identification of the need for modification at the licensee, the need for modification of internal procedures in the SNSA or even the proposal for the modification of regulations. Information system helps everybody to track the process of evaluation and proper logging of activities. (author)

  7. Experience Innovation in Tourism

    DEFF Research Database (Denmark)

    Jensen, Jens Friis; Sørensen, Flemming

    2017-01-01

    This paper discusses how front-line employees can play an important role in innovation processes that lead tourism companies from service production to experience creation. The increasing focus on experiential value by customers in general (Sundbo and Sørensen, 2013) puts pressure on service...... and typically do not consider front-line employees to be important innovation agents (Sørensen and Jensen, 2012). However, in this paper, an analysis of an experiment in Tivoli Gardens exemplifies the innovation and value creating potential of involving front-line employees in developing new practices...... companies to move from functional service production to creating experiences (Pine and Gilmore, 2013). This is also the case in tourism companies. In tourism, most encounters between employees and tourists operate on a service logic (Sørensen and Jensen, 2015). Thus, we suggest there is a value potential...

  8. ATLAS IBL operational experience

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00237659; The ATLAS collaboration

    2016-01-01

    The Insertable B-Layer (IBL) is the inner most pixel layer in the ATLAS experiment, which was installed at 3.3 cm radius from the beam axis in 2014 to improve the tracking performance. To cope with the high radiation and hit occupancy due to proximity to the interaction point, a new read-out chip and two different silicon sensor technologies (planar and 3D) have been developed for the IBL. After the long shut-down period over 2013 and 2014, the ATLAS experiment started data-taking in May 2015 for Run-2 of the Large Hadron Collider (LHC). The IBL has been operated successfully since the beginning of Run-2 and shows excellent performance with the low dead module fraction, high data-taking efficiency and improved tracking capability. The experience and challenges in the operation of the IBL is described as well as its performance.

  9. Cooperative Prototyping Experiments

    DEFF Research Database (Denmark)

    Bødker, Susanne; Grønbæk, Kaj

    1989-01-01

    This paper describes experiments with a design technique that we denote cooperative prototyping. The experiments consider design of a patient case record system for municipal dental clinics in which we used HyperCard, an off the shelf programming environment for the Macintosh. In the ecperiments we...... tried to achieve a fluent work-like evaluation of prototypes where users envisioned future work with a computer tool, at the same time as we made on-line modifications of prototypes in cooperation with the users when breakdown occur in their work-like evaluation. The experiments showed...... that it was possible to make a number of direct manipulation changes of prototypes in cooperation with the users, in interplay with their fluent work-like evaluation of these. However, breakdown occurred in the prototyping process when we reached the limits of the direct manipulation support for modification. From...

  10. Nuclear power experience

    International Nuclear Information System (INIS)

    1983-01-01

    The International Conference on Nuclear Power Experience, organized by the International Atomic Energy Agency, was held at the Hofburg Conference Center, Vienna, Austria, from 13 to 17 September 1982. Almost 1200 participants and observers from 63 countries and 20 organizations attended the conference. The 239 papers presented were grouped under the following seven main topics: planning and development of nuclear power programmes; technical and economic experience of nuclear power production; the nuclear fuel cycle; nuclear safety experience; advanced systems; international safeguards; international co-operation. The proceedings are published in six volumes. The sixth volume contains a complete Contents of Volume 1 to 5, a List of Participants, Authors and Transliteration Indexes, a Subject Index and an Index of Papers by Number

  11. The interprofessional learning experience

    DEFF Research Database (Denmark)

    Jakobsen, Flemming; Morcke, Anne Mette; Hansen, Torben Baek

    2017-01-01

    who worked in an interprofessional outpatient orthopaedic clinic from March 2015 to January 2016. The interviews were transcribed and analysed using systematic text condensation. The students’ self-reported learning experience in this outpatient clinic was characterised by direct patient contact...... we ensure that this shift maximises learning. The purpose of this article is to understand the authentic learning experience in an interprofessional outpatient clinic setting. We performed an exploratory case study with interviews of four nursing students, 13 medical students, and six staff members...... and by authentic, interprofessional, task-based learning, and a preference for indirect supervision when conducting uncomplicated patient consultations. The supervisors intended to create this interprofessional outpatient clinic experience by having a clear teaching approach based on adult learning principles...

  12. Initial Cooling Experiment (ICE)

    CERN Multimedia

    Photographic Service; CERN PhotoLab

    1978-01-01

    In 1977, in a record-time of 9 months, the magnets of the g-2 experiment were modified and used to build a proton/antiproton storage ring: the "Initial Cooling Experiment" (ICE). It served for the verification of the cooling methods to be used for the "Antiproton Project". Stochastic cooling was proven the same year, electron cooling followed later. Also, with ICE the experimental lower limit for the antiproton lifetime was raised by 9 orders of magnitude: from 2 microseconds to 32 hours. For its previous life as g-2 storage ring, see 7405430. More on ICE: 7711282, 7809081, 7908242.

  13. World Ocean Circulation Experiment

    Science.gov (United States)

    Clarke, R. Allyn

    1992-01-01

    The oceans are an equal partner with the atmosphere in the global climate system. The World Ocean Circulation Experiment is presently being implemented to improve ocean models that are useful for climate prediction both by encouraging more model development but more importantly by providing quality data sets that can be used to force or to validate such models. WOCE is the first oceanographic experiment that plans to generate and to use multiparameter global ocean data sets. In order for WOCE to succeed, oceanographers must establish and learn to use more effective methods of assembling, quality controlling, manipulating and distributing oceanographic data.

  14. The OPERA experiment

    International Nuclear Information System (INIS)

    Dracos, M.

    2004-01-01

    The OPERA (Oscillation Project with Emulsion-tRacking Apparatus) experiment aims to observe an ν μ ↔ ν τ oscillation in the parameter region allowed by previous experiments. The OPERA detector will be installed in the underground Gran Sasso Laboratory, where the CNGS (CERN Neutrino beam to Gran Sasso) ν μ beam will be produced. The signature of the presence of ν τ 's in the ν μ beam will be detection of τ leptons produced by ν τ interactions. Nuclear emulsions will be used for precise event reconstruction, while electronic detectors will be used for triggering [ru

  15. The OPERA experiment

    International Nuclear Information System (INIS)

    Jollet, C.

    2006-01-01

    The aim of the OPERA experiment is to provide unambiguous evidence for the ν μ ↔ ν τ oscillation by looking at the appearance of ν τ in a pure ν μ beam. This oscillation will be sought in the region of the oscillation parameters indicated by the atmospheric neutrino results. The experiment is part of the CNGS (CERN Neutrino beam to Gran Sasso) project. The νμ beam produced at CERN will be sent towards the Gran Sasso underground laboratory, where the OPERA detector is under construction. The detector, the physics potential, and performance for neutrino oscillation studies including the subleading ν μ ↔ ν ε search are presented

  16. The OPERA experiment

    International Nuclear Information System (INIS)

    Dracos, M.

    2004-01-01

    The OPERA (oscillation project with emulsion-tracking apparatus) experiment aims to observe an unambiguous ν μ ↔ ν τ oscillation in the parameter region allowed by previous experiments. The OPERA detector will be installed in the underground Gran Sasso Laboratory, 732 km away from CERN, where the CNGS (CERN neutrino beam to Gran Sasso) ν μ beam will be produced. The signature of the presence of ν τ 's in the ν μ beam will be the detection of τ leptons produced by ν τ interactions. Nuclear emulsions will be used for precise event reconstruction, while electronic detectors will be used for triggering

  17. The LDMX Experiment

    OpenAIRE

    Mans Jeremiah

    2017-01-01

    The thermal-relic mechanism for the production of dark-matter in the early universe, combined with the precision measurements of the cosmic microwave background and the lack of observation of dark matter at the LHC, motivates the search for dark matter in the mass range between 1 MeV and 1 GeV. We describe the concept for the Light Dark Matter Experiment (LDMX), which could carry out such a search using the missing-momentum technique. The experiment would utilize a unique high-rate, low-curre...

  18. Accessibility and sensory experiences

    DEFF Research Database (Denmark)

    Ryhl, Camilla

    2010-01-01

    and accessibility. Sensory accessibility accommodates aspects of a sensory disability and describes architectural design requirements needed to ensure access to architectural experiences. In the context of architecture accessibility has become a design concept of its own. It is generally described as ensuring...... physical access to the built environment by accommodating physical disabilities. While the existing concept of accessibility ensures the physical access of everyone to a given space, sensory accessibility ensures the choice of everyone to stay and be able to participate and experience....

  19. SUPERCOLLIDER: Planning for experiments

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    To push forward the necessarily lengthy preparations for experiments at the proposed US Superconducting Super Collider, a Workshop on Experiments, Detectors and Experimental Areas was held at Berkeley from 7 to 17 July. Participants looked ahead to the task of extracting physics (like the search for Higgs particles, supersymmetry or other heavy quarks and leptons) from the chaos of hadron collisions at 20 TeV beam energies with luminosities in excess of 10 32 . The door would also have to be left open for unexpected physics in these higher energy regions

  20. Who Needs Business Experience?

    DEFF Research Database (Denmark)

    Walter, Achim; Ritter, Thomas; Coviello, Nicole

    the founding teams’ pre-foundation R&D and customer collaborations to early exports. We also show that pre-foundation involvement in these various forms of collaboration, as well as a diverse stock of prior technical knowledge, can compensate for a lack of business experience in the team. The results also show...... that prior business experience does not predict very early export (within three years). Our results offer fresh insight to the international business and international entrepreneurship literatures, and implications for policy development. In particular, international R&D collaborations at public research...

  1. Experience and Sustainable Consumption

    DEFF Research Database (Denmark)

    Rasmussen, Tove Arendt

    2014-01-01

    Experience understood as experience-based consumption is by now fairly absent from the research agenda of the different theories on sustainable consumption. On the basis of Colin Campbell’s notion of romantic ethics and emotional sentimentality in modern hedonism, I claim that sustainable....... Very often, however, the actual purchase does not live up to the demands of doing good in the sustainable consumption chain, and the individual might end up with a guilty conscience, which again is a possible trigger for lingering in a sentimental mode of guilt. Emotions of sentimentality may actually...

  2. Experimenting with alternative economies

    DEFF Research Database (Denmark)

    Longhurst, Noel; Avelino, Flor; Wittmayer, Julia

    2016-01-01

    Neoliberalism is a powerful narrative that has shaped processes of urban economic development across the globe. This paper reports on four nascent ‘new economic’ narratives which represent fundamentally different imaginaries of the urban economy. Experiments informed by these narratives challenge...... the dominant neoliberal logic in four key dimensions: What is the purpose of economic development? What are the preferred distributive mechanisms? Who governs the economy? What is the preferred form of economic organisation? The emergence of these experiments illustrates that cities are spaces where counter...

  3. AGS experiments---1987, 1988, 1989

    International Nuclear Information System (INIS)

    Depken, J.C.

    1989-04-01

    This report contains: Experimental Areas Layout; Table of Beam Parameters and Fluxes; Experiment Schedule ''as run''; Experiment Long Range Schedule; A listing of experiments by number; Two-page summaries of each experiment begin here, also ordered by number; Publications of AGS experiments; and List of experimenters

  4. AGS experiments, 1988, 1989, 1990

    International Nuclear Information System (INIS)

    Depken, J.C.

    1991-04-01

    This report contains: experimental areas layout; table of beam parameters and fluxes; experiment schedule ''as run''; experiment long range schedule; a listing of experiments by number; two-page summaries of each experiment begin here, also ordered by number; publications of AGS experiments; and list of experimenters

  5. AGS experiments: 1985, 1986, 1987

    International Nuclear Information System (INIS)

    Depken, J.C.

    1987-01-01

    This report contains: Experimental areas layout, table of beam parameters and fluxes, experiment schedule ''as run,'' experiment long range schedule, a listing of experiments by number, two-page summaries of each experiment, also ordered by number, and publications of AGS experiments, 1982-1987

  6. A Vibrating String Experiment

    Science.gov (United States)

    Tsutsumanova, Gichka; Russev, Stoyan

    2013-01-01

    A simple experiment demonstrating the excitation of a standing wave in a metal string is presented here. Several tasks using the set-up are considered, which help the students to better understand the standing waves, the interaction between electric current and magnetic field and the resonance phenomena. This can serve also as a good lecture…

  7. The Santabot Experiment

    DEFF Research Database (Denmark)

    2009-01-01

    The focus is to study people's willingness to interact, and their reaction when a robot enters their daily environment. The robot autonomously detects and follows people, while keeping a safe distance. The conclusion was that people were positive towards robots in their daily life. The experiments...

  8. The Majorana Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Aalseth, Craig E.; Aguayo Navarrete, Estanislao; Amman, M.; Avignone, F. T.; Back, Henning O.; Bai, Xinhua; Barabash, Alexander S.; Barbeau, P. S.; Bergevin, M.; Bertrand, F.; Boswell, M.; Brudanin, V.; Bugg, William; Burritt, Tom H.; Busch, Matthew; Capps, Greg L.; Chan, Yuen-Dat; Collar, J. I.; Cooper, R. J.; Creswick, R.; Detwiler, Jason A.; Diaz, J.; Doe, Peter J.; Efremenko, Yuri; Egorov, Viatcheslav; Ejiri, H.; Elliott, S. R.; Ely, James H.; Esterline, James H.; Farach, H. A.; Fast, James E.; Fields, N.; Finnerty, P.; Fraenkle, Florian; Gehman, Victor M.; Giovanetti, G. K.; Green, M.; Guiseppe, Vincente; Gusey, K.; Hallin, A. L.; Harper, Gregory; Hazama, R.; Henning, Reyco; Hime, Andrew; Hong, H.; Hoppe, Eric W.; Hossbach, Todd W.; Howard, Stanley; Howe, M. A.; Johnson, R. A.; Keeter, K.; Keillor, Martin E.; Keller, C.; Kephart, Jeremy D.; Kidd, M. F.; Knecht, A.; Kochetov, Oleg; Konovalov, S.; Kouzes, Richard T.; LaRoque, B. H.; Leviner, L.; Loach, J. C.; Luke, P.; MacMullin, S.; Marino, Michael G.; Martin, R. D.; Medlin, D.; Mei, Dong-Ming; Miley, Harry S.; Miller, M. L.; Mizouni, Leila; Myers, Allan W.; Nomachi, Masaharu; Orrell, John L.; Peterson, David; Phillips, D.; Poon, Alan; Perevozchikov, O.; Perumpilly, Gopakumar; Prior, Gersende; Radford, D. C.; Reid, Douglas J.; Rielage, Keith; Robertson, R. G. H.; Rodriguez, Larry; Ronquest, M. C.; Salazar, Harold; Schubert, Alexis G.; Shima, T.; Shirchenko, M.; Sobolev, V.; Steele, David; Strain, J.; Swift, Gary; Thomas, K.; Timkin, V.; Tornow, W.; Van Wechel, T. D.; Vanyushin, I.; Varner, R. L.; Vetter, Kai; Vorren, Kris R.; Wilkerson, J. F.; Wolfe, B. A.; Xiang, W.; Yakushev, E.; Yaver, Harold; Young, A.; Yu, Chang-Hong; Yumatov, V.; Zhang, C.

    2011-08-01

    The Majorana Collaboration is assembling an array of HPGe detectors to search for neutrinoless double-beta decay in 76Ge. Initially, Majorana aims to construct a prototype module to demonstrate the potential of a future 1-tonne experiment. The design and potential reach of this prototype Demonstrator module are presented.

  9. The OLYMPUS experiment

    International Nuclear Information System (INIS)

    Milner, R.; Hasell, D.K.; Kohl, M.; Schneekloth, U.; Akopov, N.; Alarcon, R.; Andreev, V.A.; Ates, O.; Avetisyan, A.; Bayadilov, D.; Beck, R.; Belostotski, S.; Bernauer, J.C.; Bessuille, J.; Brinker, F.; Buck, B.; Calarco, J.R.; Carassiti, V.; Cisbani, E.; Ciullo, G.

    2014-01-01

    The OLYMPUS experiment was designed to measure the ratio between the positron–proton and electron–proton elastic scattering cross-sections, with the goal of determining the contribution of two-photon exchange to the elastic cross-section. Two-photon exchange might resolve the discrepancy between measurements of the proton form factor ratio, μ p G E p /G M p , made using polarization techniques and those made in unpolarized experiments. OLYMPUS operated on the DORIS storage ring at DESY, alternating between 2.01 GeV electron and positron beams incident on an internal hydrogen gas target. The experiment used a toroidal magnetic spectrometer instrumented with drift chambers and time-of-flight detectors to measure rates for elastic scattering over the polar angular range of approximately 25°–75°. Symmetric Møller/Bhabha calorimeters at 1.29° and telescopes of GEM and MWPC detectors at 12° served as luminosity monitors. A total luminosity of approximately 4.5 fb −1 was collected over two running periods in 2012. This paper provides details on the accelerator, target, detectors, and operation of the experiment

  10. Future of neutrino experiments

    Indian Academy of Sciences (India)

    needs to be controlled to be less than 1%. To achieve this goal, each experimental group has been carefully designing the experiment with the identical near and far detectors, optimized baseline length (1 to 2 km), deep enough locations to reduce the cosmic ray-induced backgrounds, thick enough shielding, veto counters, ...

  11. The COMPASS experiment

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    Detail of one of the magnets on the Common Muon and Proton Apparatus for Structure and Spectroscopy (COMPASS) experiment. COMPASS studies the structure of composite particles which interact via the strong force, called hadrons. These have a complicated internal structure due to the nature of their force carriers, gluons, which can form self interacting bunches called glueballs.

  12. Electronics for LHC Experiments

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    This document gathers the abstracts of most presentations made at this workshop on electronics for the large hadron collider (LHC) experiments. The presentations were arranged into 6 sessions: 1) electronics for tracker, 2) trigger electronics, 3) detector control systems, 4) data acquisition, 5) electronics for calorimeters and electronics for muons, and 6) links, power systems, grounding and shielding, testing and quality assurance.

  13. HCDA bubble experiment, (2)

    International Nuclear Information System (INIS)

    Sakata, Kaoru; Mashiko, Hiroyuki; Oka, Yoshiaki; An, Shigehiro; Isozaki, Tadashi.

    1981-06-01

    An experiment simulating the behavior of the very large steam bubbles generated at the time of an accident of core collapse was carried out with a warm water tank, and the applicability of the theory of very small bubble disappearance known at present was examined. The bubbles generated in HCDA (hypothetical core disruptive accident) are expected to be very large, containing sodium, fuel, FP gas and so on, and play important role in the mechanism of emitting radioactive substances in the safety analysis of LMFBRs. In this experiment, the degree of subcool of the warm water pool, the initial radii of steam bubbles and the blowoff pressure of steam were taken as the parameters. The radius of the steam bubbles generated in the experiment was about 6.5 cm, and the state of disappearance was different above and below the degree of unsaturation of 10 deg C. Comparing the disappearance curve obtained by the experiment with the theory of disappearance of small bubbles, the experimental values were between inertia-controlled disappearance and heat transfer-controlled disappearance, and this result was able to be explained generally with the model taking the pressure change within steam bubbles into account. The rise of bubbles was also observed. (Kako, I.)

  14. Experience as Excursion

    DEFF Research Database (Denmark)

    Svabo, Connie; Shanks, Michael

    2014-01-01

    researchers and practitioners to travel – making it possible to follow experiences as they are enacted across and between places, modes of transportation, mobile mediation and assemblages of things. Drawing on the nomadic metaphysics of philosopher Michel Serres, the journeying, shifting and propagating...

  15. Experience and Sustainable Consumption

    DEFF Research Database (Denmark)

    Rasmussen, Tove Arendt

    Experience understood as experience-based consumption is by now fairly absent from the research agenda of the different theories on sustainable consumption. On the basis of Colin Campbell’s notion of romantic ethics and emotional sentimentality in modern hedonism, I claim that sustainable consump...... convince the individual that she really does care for others and thereby provide a positive experience of feeling good – even if it takes place in the universe of consumption fantasies only....... consumption may re-enchant ordinary consumption and thereby even become a part of marketing and the experience economy. New layers of meaning are at stake and altruistic motives come into play; doing something good for someone or something, aside from oneself, is a very strong trigger of positive emotions....... Very often, however, the actual purchase does not live up to the demands of doing good in the sustainable consumption chain, and the individual might end up with a guilty conscience, which again is a possible trigger for lingering in a sentimental mode of guilt. Emotions of sentimentality may actually...

  16. New neutrino experiments

    Indian Academy of Sciences (India)

    1999-03-26

    radioactive waste left from the research and production of nuclear weapons. After more than 20 years of scientific study, public input, and regulatory struggles, WIPP began operations on March 26, 1999. It is considered as a possible site for the supernova experiment OMNIs which will feature a measurement of the neutral.

  17. Stage theta pinch experiments

    International Nuclear Information System (INIS)

    Linford, R.K.; Downing, J.N.; Gribble, R.F.; Jacobson, A.R.; Platts, D.A.; Thomas, K.S.

    1975-01-01

    The Staged Theta Pinch program is designed to study the technological and physics problems associated with producing fat plasmas and separating the implosion heating from the adiabatic compression. Several methods of implosion heating are discussed. Circuit diagrams and theoretical magnetic field behavior are described for the STP and resonant heating experiments. (MOW)

  18. The OLYMPUS experiment

    Energy Technology Data Exchange (ETDEWEB)

    Milner, R.; Hasell, D.K. [Massachusetts Institute of Technology, Cambridge, MA (United States); Kohl, M. [Hampton Univ., Hampton, VA (United States); Collaboration: The OLYMPUS Collaboration; and others

    2013-12-15

    The OLYMPUS experiment was designed to measure the ratio between the positron-proton and electron-proton elastic scattering cross sections, with the goal of determining the contribution of two-photon exchange to the elastic cross section. Two-photon exchange might resolve the discrepancy between measurements of the proton form factor ratio, {mu}{sub p}G{sup p}{sub E}/G{sup p}{sub M}, made using polarization techniques and those made in unpolarized experiments. OLYMPUS operated on the DORIS storage ring at DESY, alternating between 2.01 GeV electron and positron beams incident on an internal hydrogen gas target. The experiment used a toroidal magnetic spectrometer instrumented with drift chambers and time-of-flight detectors to measure rates for elastic scattering over the polar angular range of approximately 25 -75 . Symmetric Moeller/Bhabha calorimeters at 1.29 and telescopes of GEM and MWPC detectors at 12 served as luminosity monitors. A total luminosity of approximately 4.5 fb{sup -1} was collected over two running periods in 2012. This paper provides details on the accelerator, target, detectors, and operation of the experiment.

  19. Prospects in coincidence experiments

    International Nuclear Information System (INIS)

    Laget, J.M.

    1984-01-01

    The sensitivity of virtual photons to the local variations of the charge and magnetization densities is exploited to study the short-range part of the nucleon-nucleon interaction inside the nucleus. The possibility of varying energy, squared mass and longitudinal polarization of the photons independently enables us to disentangle the mechanisms related to the internal structure of the nucleon (e.g. quark interchange) and the contribution due to meson exchange. Coincidence experiments of the type (e,e'N) and (e,e'NN) are performed to suppress the meson contribution to the longitudinal part of the quasi-elastic peak. Four typical examples of coincidence experiments induced by virtual photons are discussed: experiments (1) on the spectroscopic structure of the quasi-elastic peak and the problem of deep lying hole states; (2) on the structure of the continuum; (3) on the low energy side of the quasi-elastic peak; and finally a three-arm coincidence experiment. (Auth.)

  20. The KOSI experiments

    International Nuclear Information System (INIS)

    Huebner, W.F.

    1991-01-01

    Whipply's icy conglomerate model of the comet nucleus has enjoyed progressively increasing acceptance and success in explaining Earth-based observations of comets since its very inception (Whipple, 1950, 1951). According to this model, the nucleus is a solid body composed of frozen gases and dust. The missions to Comet Halley in 1986, in particular the Vega and the Giotto missions, have confirmed that there is a single solid nucleus that is the root of all the observed phenomena that can be associated with an active comet. Two new comet mission (CRAF and Rosetta) are planned by NASA and ESA to extract further details about the structure and composition of the nucleus. Laboratory experiments play an important role in defining and identifying the objectives of these missions. Although such experiments have been carried out in many laboratories in Europe, the Soviet Union, the USA, Israel, and Japan, the KOSI experiments are the first large-scale investigations (in spatial dimensions and duration). (KOSI is an acronym for Kometensimulation, German for comet simulation). Starting with a summary and explanation of the KOSI experiments by Grun et al. (1991) and some of the experimental limitations by Keller and Markiewicz (1991), the author reports in this special issue the progress achieved about halfway through the planned series of investigations

  1. Experiments with Retraining.

    Science.gov (United States)

    Shultz, George P.; Weber, Arnold R.

    When Armour and Company faced a shutdown of six plants, it joined in a cooperative program of vocational retraining with two labor unions; an Automation Fund Committee was formed, with representation from management, the unions, and "public" (college professors); and an experimental program in Oklahoma City provided experience which was…

  2. Self managing experiment resources

    International Nuclear Information System (INIS)

    Stagni, F; Ubeda, M; Charpentier, P; Tsaregorodtsev, A; Romanovskiy, V; Roiser, S; Graciani, R

    2014-01-01

    Within this paper we present an autonomic Computing resources management system, used by LHCb for assessing the status of their Grid resources. Virtual Organizations Grids include heterogeneous resources. For example, LHC experiments very often use resources not provided by WLCG, and Cloud Computing resources will soon provide a non-negligible fraction of their computing power. The lack of standards and procedures across experiments and sites generated the appearance of multiple information systems, monitoring tools, ticket portals, etc... which nowadays coexist and represent a very precious source of information for running HEP experiments Computing systems as well as sites. These two facts lead to many particular solutions for a general problem: managing the experiment resources. In this paper we present how LHCb, via the DIRAC interware, addressed such issues. With a renewed Central Information Schema hosting all resources metadata and a Status System (Resource Status System) delivering real time information, the system controls the resources topology, independently of the resource types. The Resource Status System applies data mining techniques against all possible information sources available and assesses the status changes, that are then propagated to the topology description. Obviously, giving full control to such an automated system is not risk-free. Therefore, in order to minimise the probability of misbehavior, a battery of tests has been developed in order to certify the correctness of its assessments. We will demonstrate the performance and efficiency of such a system in terms of cost reduction and reliability.

  3. Ultrafast gas switching experiments

    International Nuclear Information System (INIS)

    Frost, C.A.; Martin, T.H.; Patterson, P.E.; Rinehart, L.F.; Rohwein, G.J.; Roose, L.D.; Aurand, J.F.; Buttram, M.T.

    1993-01-01

    We describe recent experiments which studied the physics of ultrafast gas breakdown under the extreme overvoltages which occur when a high pressure gas switch is pulse charged to hundreds of kV in 1 ns or less. The highly overvolted peaking gaps produce powerful electromagnetic pulses with risetimes Khz at > 100 kV/m E field

  4. SAMBA Project Experiences

    Science.gov (United States)

    Fuhrhop, Christian; Vaidya, Raju; Mayora, Oscar; Furtado, Elizabeth

    The purpose of the SAMBA project, running from January 2007 to February 2009, was to create a framework for allowing local communities and citizens (including low income population) to access community-oriented content and services by means of iDTV channels, specifically MHP over DVB-T. This paper summarises the project and the experiences gained from it.

  5. [The AMY experiment

    International Nuclear Information System (INIS)

    1989-01-01

    The AMY experiment is one of three major experiments at TRISTAN which is studying the states the matter produced in electron positron annihilations in the center of mass energy range of 50--65GeV. It provides information between the lower energy facilities such as PEP and PETRA and the new facilities SLC and LEP which are designed to operate in the region of the Z 0 mass near 90GeV. In the region of the AMY experiment, interaction cross sections are near their minimum of about 100pb, making it difficult to acquire large data samples during typical running cycles. This last year has seen an accumulation of about 10---12pb -1 of integrated luminosity in the energy range from 58 to 61.7GeV. Despite this limited data sample, the AMY experiment has been extremely active in attempting to extract the minimum amount of information from the data. Some of the most significant results are discussed in this paper. 9 refs

  6. Expectations for neutron experiments

    International Nuclear Information System (INIS)

    Tonomura, Akira

    1993-01-01

    An electron wave function's phase distribution can now be precisely measured to 1/100th of the electron wavelength using both electron holography and a 'coherent' field-emission electron beam. This technique has opened up a new way to conduct thought experiments once regarded as experimentally impossible and also allows the ultra-fine measurement of material structures and field distributions. (author)

  7. FLORIDA TOWER FOOTPRINT EXPERIMENTS

    Energy Technology Data Exchange (ETDEWEB)

    WATSON,T.B.; DIETZ, R.N.; WILKE, R.; HENDREY, G.; LEWIN, K.; NAGY, J.; LECLERC, M.

    2007-01-01

    The Florida Footprint experiments were a series of field programs in which perfluorocarbon tracers were released in different configurations centered on a flux tower to generate a data set that can be used to test transport and dispersion models. These models are used to determine the sources of the CO{sub 2} that cause the fluxes measured at eddy covariance towers. Experiments were conducted in a managed slash pine forest, 10 km northeast of Gainesville, Florida, in 2002, 2004, and 2006 and in atmospheric conditions that ranged from well mixed, to very stable, including the transition period between convective conditions at midday to stable conditions after sun set. There were a total of 15 experiments. The characteristics of the PFTs, details of sampling and analysis methods, quality control measures, and analytical statistics including confidence limits are presented. Details of the field programs including tracer release rates, tracer source configurations, and configuration of the samplers are discussed. The result of this experiment is a high quality, well documented tracer and meteorological data set that can be used to improve and validate canopy dispersion models.

  8. Modelling Urban Experiences

    DEFF Research Database (Denmark)

    Jantzen, Christian; Vetner, Mikael

    2008-01-01

    How can urban designers develop an emotionally satisfying environment not only for today's users but also for coming generations? Which devices can they use to elicit interesting and relevant urban experiences? This paper attempts to answer these questions by analyzing the design of Zuidas, a new...

  9. Olkiluoto 3 Experience

    International Nuclear Information System (INIS)

    Tiippana, Petteri

    2011-01-01

    This paper discusses the experience from the Olkiluoto 3 nuclear power plant project from regulator's point of view. There are certain factors that have affected greatly the project progress. First, Olkiluoto 3 nuclear power plant is the first European Pressurised Reactor (EPR) being constructed. Secondly, construction of the unit started after a fairly long break in nuclear power plant construction in Europe, which had resulted in loss of experienced and qualified engineering and manufacturing resources. These factors have to be kept in mind when evaluating the experience from Olkiluoto 3. Experience discussed in this paper have to do with the licensing and regulatory oversight process, completion of the design prior to construction, experience and know-how of the participating organisations, quality management in a nuclear construction project, advanced manufacturing and construction technologies, turnkey contract with regard to licensee's responsibility, safety culture aspects in a nuclear construction project, and the role and importance of regulator's oversight. (author)

  10. Experience, Poetry and Truth

    DEFF Research Database (Denmark)

    Gahrn-Andersen, Rasmus

    2017-01-01

    of philosophical thinking. Specifically, I show that, beneath a highly poetic and obscure prose, Jünger posits how subjective experience and poetry allow individuals to realize truth. I relate parts of Jünger’s insights to contributions by Husserl, Heidegger and Merleau-Ponty, arguing that Jünger offers a unique...

  11. United Kingdom's experience

    International Nuclear Information System (INIS)

    Drummond, S.M.

    1994-01-01

    This is a presentation of the United Kingdom's experience with power transmission open access. The topics of the presentation include the objectives of changing, commercial arrangements and economic drivers, long term effects, the effects of moving to a more competitive environment, and factors affecting open access such as political climate and market regulation

  12. Alignement experience in STAR

    CERN Document Server

    Margetis, S; Lauret, J; Perevozchikov, V; Van Buren, G; Bouchef, J

    2007-01-01

    The STAR experiment at RHIC uses four layers of silicon strip and silicon drift detectors for secondary vertex reconstruction. An attempt for a direct charm meson measurement put stringent requirements on alignment and calibration. We report on recent alignment and drift velocity calibration work performed on the inner silicon tracking system.

  13. Caring Experience and Knowledge

    DEFF Research Database (Denmark)

    Dybbroe, Betina

    2005-01-01

    ,didactics and educational thinking- and students experiences and sensing, and illuminates excluding processes in classrooms related to emotional, non-cognitive and relational aspects of the qualifying process. This is set into a larger framework of the biographical professionalization processes of students......, and to the clash between competing rationalities, that cause dilemmas in care....

  14. Experiments using coincidence methods

    International Nuclear Information System (INIS)

    Anwar Dhani.

    1978-01-01

    Experiments on γ spectroscopy using the simple coincidence techniques, including investigation of angular distribution of γ radiation from annihilation process in decay of Na 22 , γ - γ angular correlation technique in decay of Co 60 , decay scheme study of Bi 207 and life time measurement of nuclear Pb 207 excited state have been carried out. (author)

  15. The Transgender Military Experience

    Directory of Open Access Journals (Sweden)

    Michelle Dietert

    2015-04-01

    Full Text Available Although there have been studies that focus on the experiences of the gay and lesbian population serving in the United States military, few have focused on the experience of active duty transgender service members. Transgender individuals transgress the binary conception of gender by deviating from societal gender norms associated with assigned sex at birth. The Department of Defense has set policies and standards that reflect a binary conception of gender, with a focus on conformity. We argue that able-bodied gender variant service personnel are just as capable of serving their country as anyone else. Because of the repercussions associated with active duty transgender military personnel, our sample is small and involves nine clandestine service members and two international service members who wanted to share their stories from a different perspective. Snowball sampling was aimed at finding current active duty and reserve transgender service members. Using a combination of telephone interviews and questionnaires, data were collected from active duty transgender service personnel throughout the United States and two from international militaries that allow transgender people to serve. Data collection focused on the overall experiences of the participants along with questions regarding workplace discrimination, suggestions for policy changes, and their views about the overturn of Don’t Ask, Don’t Tell. Our findings add to a growing source of information about the transgender military experience in the U.S. armed forces and the importance of overturning discriminatory workplace policies that negatively impact transgender service members.

  16. [Ethics and animal experiments.].

    Science.gov (United States)

    Schnaider, Taylor Brandão; Souza, Cláudio de

    2003-04-01

    This is a major subject since the aim is to grant human beings physical, mental, social and spiritual well-being without forgetting the sacred rights of all animals. Most international codes dealing with health-related research practices state that research developed in human beings should be based on previous lab animal experiments or on other scientific data. This article aimed at explaining ethics in animal experiments. The concepts of dissertation and thesis, experimental thesis, experimental essay or pilot experiment and experimental animal facilities are reviewed. Then, a historical retrospective is drawn about the first attempt to develop experimental research policies during the mid 19th Century, in London. It is highlighted that some criteria defined by that time still persist. The first animal research ethical committee was created in Sweden in 1979, followed by the USA in1984. In Brazil, animal research ethical committees were created as late as in the 90s. The Federal Law 6638 was passed in May 1979 and provides for the didactic-scientific practice of animal vivisection. This law, however, is still waiting for regulation. In addition, there are some drafts being analyzed by the Congress, which provide for the use of animals for teaching and research purposes. Finally, the policies adopted by the Brazilian College of Animal Experiments and the Universal Declaration of Animal Rights are presented. Professors, postgraduates, residents and graduate students of a Medical School involved in animal research should be aware of the ethical principles aiming at protecting animals selected for scientific work.

  17. Long baseline neutrino experiments

    Indian Academy of Sciences (India)

    Atmospheric neutrino experiments (IMB, Kamiokande, Super-Kamiokande (SK)) show that νµ created in cosmic ray interactions with atmospheric nuclei are being converted into ντ but νe created in such interactions are unaffected. SK measure- ment of νµ and νe event rates as functions of zenith angle is the key ...

  18. Belief Elicitation in Experiments

    DEFF Research Database (Denmark)

    Blanco, Mariana; Engelmann, Dirk; Koch, Alexander

    Belief elicitation in economics experiments usually relies on paying subjects according to the accuracy of stated beliefs in addition to payments for other decisions. Such incentives, however, allow risk-averse subjects to hedge with their stated beliefs against adverse outcomes of other decisions......-belief elicitation treatment using a financial investment frame, where hedging arguably would be most natural....

  19. The big experiment

    CERN Multimedia

    MacEacheran, Mike

    2010-01-01

    "From an academic laboratory in Switzerland, Cern, the European Organisation for Nuclear Research, is conducting physics experiments that are mesmerising everyone. But are its scientitsts really going to answer the questions of life, the Univers and everyhing in between?" (4 pages)

  20. My experience with research

    Indian Academy of Sciences (India)

    Lawrence

    me to Guwahati to Cotton College, the premier college of the. North Eastern region. ... ate college. Although it was a very rewarding experience, I knew in my heart that scientific research was my true calling. The Head of the Department of Physics at Dibrugarh Uni- ... Let alone the State Government, even other physicists in ...

  1. Visual experience and blindsight

    DEFF Research Database (Denmark)

    Overgaard, Morten

    2011-01-01

    Blindsight is classically defined as residual visual capacity, e.g., to detect and identify visual stimuli, in the total absence of perceptual awareness following lesions to V1. However, whereas most experiments have investigated what blindsight patients can and cannot do, the literature contains...

  2. Psychotic experiences and religiosity

    DEFF Research Database (Denmark)

    Kovess-Masfety, V; Saha, S; Lim, C C W

    2018-01-01

    OBJECTIVES: Religiosity is often associated with better health outcomes. The aim of the study was to examine associations between psychotic experiences (PEs) and religiosity in a large, cross-national sample. METHODS: A total of 25 542 adult respondents across 18 countries from the WHO World Ment...

  3. Enhance Your Twitter Experience

    Science.gov (United States)

    Miller, Shannon McClintock

    2010-01-01

    The author has been encouraging teachers, students, and others to join Twitter and build their personal learning networks (PLNs) ever since she delved into this great social networking site. In this article, she offers a few other tools and tips that can improve the Twitter experience of those who have opened up an account and dabbled a bit but…

  4. Sampling the Deaf Experience.

    Science.gov (United States)

    Teller, Henry E.; And Others

    1993-01-01

    Two graduate students in deaf education wore ear plugs for two months to simulate hearing loss, and recorded their experiences and feelings. Excerpts from their journals are presented, commenting on such daily activities as shopping at a mall, watching television, driving, babysitting, and attending a football game. (JDD)

  5. A Harmonic Motion Experiment

    Science.gov (United States)

    Gluck, P.; Krakower, Zeev

    2010-01-01

    We present a unit comprising theory, simulation and experiment for a body oscillating on a vertical spring, in which the simultaneous use of a force probe and an ultrasonic range finder enables one to explore quantitatively and understand many aspects of simple and damped harmonic motions. (Contains 14 figures.)

  6. Water Flow Experiments

    Indian Academy of Sciences (India)

    This is a simple exercise in elementary fluid dynamics for the undergraduate and the secondary school level. Here, we explore the flow of water through an orifice at the bottom of a cylindri- cal bottle/tank, first through a tube attached to the bottom of the bottle/tank and then without the tube. The experiment is easy to perform.

  7. T be Nnewi Experience

    African Journals Online (AJOL)

    Ugochukwu EF, Ezechukwu CC, Agbata CC, Ezumba I. Preterm Admissions in a. Special Care Baby Unit: The Nnewi Experience. Nigerian Journal of Paediatrics. 2002;29:75. A review of all preterm admissions into the Special Care Bay Unit' of the. Nnamdi Azikiwe University Teaching Hospital (NAUTH), Nnewi, over a ...

  8. A Simple Adsorption Experiment

    Science.gov (United States)

    Guirado, Gonzalo; Ayllon, Jose A.

    2011-01-01

    The study of adsorption phenomenon is one of the most relevant and traditional physical chemistry experiments performed by chemistry undergraduate students in laboratory courses. In this article, we describe an easy, inexpensive, and straightforward way to experimentally determine adsorption isotherms using pieces of filter paper as the adsorbent…

  9. Parent Hearing Aid Experiences

    Science.gov (United States)

    Munoz, Karen; Roberts, Mallory; Mullings, Day; Harward, Richard

    2012-01-01

    This study addresses parent experiences in obtaining and managing hearing aids for their young child. The purpose was to identify challenges parents encounter to determine what state agencies can do to improve parent access to amplification. Data were collected July through September of 2010; 40 parents of children ages birth to 3 years old…

  10. Literature on photoproduction experiments

    International Nuclear Information System (INIS)

    Joos, P.

    1975-10-01

    Literature on gamma-proton, gamma-neutron, gamma-deuteron, gamma-nucleus experiments, inclusive photoproduction, particle yields in gamma-proton and gamma-nucleus, inelastic compton scattering, search for new particles, Primakoff effect, photofission, and QED-tests are compiled. (BJ) [de

  11. CANDU operating experience

    International Nuclear Information System (INIS)

    McConnell, L.G.; Woodhead, L.W.; Fanjoy, G.R.

    1982-03-01

    The CANDU Pressurized Heavy Water (CANDU-PHW) type of nuclear electric generating station has been developed jointly by Atomic Energy of Canada Limited and Ontario Hydro. This paper highlights Ontario Hydro's operating experience using the CANDU-PHW system, with a focus on the operating performance and costs, reliability of system components and nuclear safety considerations both to the workers and the public

  12. Electronics for LHC Experiments

    International Nuclear Information System (INIS)

    2004-01-01

    This document gathers the abstracts of most presentations made at this workshop on electronics for the large hadron collider (LHC) experiments. The presentations were arranged into 6 sessions: 1) electronics for tracker, 2) trigger electronics, 3) detector control systems, 4) data acquisition, 5) electronics for calorimeters and electronics for muons, and 6) links, power systems, grounding and shielding, testing and quality assurance

  13. Globalization: The European Experience.

    Science.gov (United States)

    Goldsmith, Peter

    1996-01-01

    The experience of the United Kingdom and other European countries in designing legal education which responds to the changing needs of the European Union is described. The three-stage British system of legal education is outlined, and the impact of European Union formation discussed briefly. Changes in undergraduate study, professional training,…

  14. The Mobilisatsia experience

    International Nuclear Information System (INIS)

    De Boever, P.

    2005-01-01

    The hazards of long-duration manned space flight are real. In order to participate effectively in long duration orbital missions or to continue the exploration of space, the health of the astronaut must be secured. There is mounting evidence that changes in the immune response of an astronaut in short-term flights, resemble those occurring after acute stress, while the changes during long-term flights resemble those caused by chronic stress. This blunting of the immune system occurs concomitant with a relative increase in microbial contamination in the space cabin environment. Such a combination of events results in an increased probability of in-flight infectious events. Micro-organisms are subject to a genetic evolution, which may lead to the capacity to colonize new environments and to cause infections. Central players in this evolutionary process are mobile genetic elements. They help to mobilize and reorganize genes, be it within a given genome (intragenomic mobility) or between bacterial cells (intercellular mobility). Hence, the processes of genetic exchange can mobilize genetic elements between bacterial strains, and therefore play a role in determining the infectious potential. The specific confined environment and space-flight related factors (such as microgravity and cosmic radiation) may increase the frequency in which mobile genetic elements are exchanged between micro organisms. The aim of the Mobilisatsia experiment was to promote microbial gene transfer under space flight conditions during a short-term experiment conducted aboard the International Space Station (ISS). The efficiency of the gene exchange process was compared with a synchronously performed ground control experiment. An experiment was carried out with well-characterized Gram-negative reference strains and one experiment was done with Gram-positive reference strains

  15. Continuous solvent extraction feed adjustment for HTGR fuel reprocessing. Interim development report

    International Nuclear Information System (INIS)

    Olguin, L.J.

    1978-06-01

    The two-cycle Acid-Thorex solvent extraction process requires that the feed stream to each thorium cycle be processed to reduce its nitric acid concentration (feed adjustment). This interim development report presents the results of bench-scale and pilot-plant-scale feed adjustment experiments using a continuous mode of operation. An examination of formic acid denitration and fluoride ion volatilization is also included

  16. Upscaling of U(VI) Desorption and Transport Using Decimeter-Scale Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, Derrick [Colorado School of Mines, Golden, CO (United States)

    2014-12-22

    Experimental work was used to validate modeling studies and develop multicontinuum models of U(VI) transport in a contaminated aquifer. At the bench scale, it has been shown that U(VI) desorption is rate-limited and that rates are dependent on the bicarbonate concentration. Two decimeter-scale experiments were conducted in order to help establish rigorous upscaling approaches that could be tested at the tracer test and plume scales.

  17. Sulfur dioxide reactions on ice surfaces: Implications for dry deposition to snow

    Science.gov (United States)

    Martha H. Conklin; Richard A. Sommerfeld; S. Kay Laird; John E. Villinski

    1993-01-01

    Controlled exposure of ice to a reactive gas, SO2, demonstrated the importance of the chemical composition of the ice surface on the accumulation of acidity in snow. In a series of bench-scale continuous-flow column experiments run at four temperatures (-1, -8, -30 and -60°C), SO2 was shown to dissolve and to react with other species in the ice-air interfacial region...

  18. Water as a Reagent for Soil Remediation

    Energy Technology Data Exchange (ETDEWEB)

    Jayaweera, Indira S.; Marti-Perez, Montserrat; Diaz-Ferrero, Jordi; Sanjurjo, Angel

    2003-03-06

    SRI International conducted experiments in a two-year, two-phase process to develop and evaluate hydrothermal extraction technology, also known as hot water extraction (HWE) technology, for remediating petroleum-contaminated soils. The bench-scale demonstration of the process has shown great promise, and the implementation of this technology will revolutionize the conventional use of water in soil remediation technologies and provide a standalone technology for removal of both volatile and heavy components from contaminated soil.

  19. Transformations of emotional experience.

    Science.gov (United States)

    de Cortiñas, Lia Pistiner

    2013-06-01

    In this paper the author approaches mental pain and the problems in a psychoanalytic treatment of patients with difficulties in the psychic transformation of their emotional experiences. The author is interested in the symbolic failure related to the obstruction of development of phantasies, dreams, dream-thoughts, etc. She differentiates symbolization disturbances related to hypertrophic projective identification from a detention of these primitive communications and emotional isolation. She puts forward the conjecture that one factor in the arrest of this development is the detention of projective identifications and that, when this primitive means of communication is re-established in a container-contained relationship of mutual benefit, this initiates the development of a symbolization process that can replace the pathological 'protection'. Another hypothesis she develops is that of inaccessible caesuras that, associated with the detention of projective identification, obstruct any integrative or interactive movement. This caesura and the detention of projective identifications affect mental functions needed for dealing with mental pain. The personality is left with precarious mental equipment for transforming emotional experiences. How can a psychoanalytical process stimulate the development of creative symbolization, transforming the emotional experiences and leading towards mental growth? The author approaches the clinical problem with the metaphor of the psychic birth of emotional experience. The modulation of mental pain in a container-contained relationship is a central problem for the development of the human mind. For discovering and giving a meaning to emotional experience, the infant depends on reverie, a function necessary in order to develop an evolved consciousness capable of being aware, which is different from the rudimentary consciousness that perceives but does not understand. The development of mature mental equipment is associated with the

  20. Results of recent LOFT experiments

    International Nuclear Information System (INIS)

    Leach, L.P.; Hanson, D.J.; Batt, D.L.

    1982-01-01

    Five experiments were performed in the Loss-of-Fluid Test (LOFT) facility during the past year. The experiments conducted spanned a wide range of potential accident scenarios, including large and small break loss-of-coolant accidents (LOCAs), control rod withdrawal accidents, uncontrolled boron dilution, and anticipated transients without scram (ATWS). This summary describes these experiments and presents results available from the experiments and experiment prediction calculations. A brief overview is given for the remaining experiment planned in the LOFT Program

  1. LCLS The First Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Galayda, John N

    2003-02-10

    The Scientific Advisory Committee (SAC) for the Linac Coherent Light Source (LCLS) has selected six scientific experiments for the early phase of the project. The LCLS, with proposed construction in the 2003-2006 time frame, has been designed to utilize the last third of the existing Stanford Linear Accelerator Center (SLAC) linac. The linac produces a high-current 5-15 GeV electron beam that is bunched into 230 fs slices with a 120 Hz repetition rate. When traveling through a sufficiently long (of order of 100 m) undulator, the electron bunches will lead to self amplification of the emitted x-ray intensity constituting an x-ray free electron laser (XFEL). If funded as proposed, the LCLS will be the first XFEL in the world, operating in the 800-8,000 eV energy range. The emitted coherent x-rays will have unprecedented brightness with 10{sup 12}-10{sup 13} photons/pulse in a 0.2-0.4% energy bandpass and an unprecedented time structure with a design pulse length of 230 fs. Studies are under way to reduce the pulse length to tens of femtoseconds. This document presents descriptions of the early scientific experiments selected by SAC in the spring of 2000. They cover a wide range of scientific fields. The experimental teams consist of many internationally recognized scientists who are excited about the unprecedented x-ray capabilities of LCLS that surely will lead to new scientific frontiers. More generally, this document serves to forward the scientific case for an accelerator-based XFEL source, as requested by the BESAC subpanel on Novel Coherent Light Sources, chaired by Stephen R. Leone. Two general classes of experiments are proposed for the LCLS. The first class consists of experiments where the x-ray beam is used to probe the sample without modifying it, as is done in most experiments at current synchrotron sources. In the second class, the LCLS beam is used to induce non-linear photo-processes or matter in extreme conditions. The same source can be used for

  2. Experimenting with Bulbs

    Science.gov (United States)

    Cavicchi, Elizabeth M.

    1998-04-01

    What questions come about as learners explore physical materials? How does their learning deepen through inventing experiments and making and testing their own interpretations? I present episodes from the investigatory work of three adult learners who met regularly with me to explore batteries, bulbs and wires. I taught by engaging the learners' interest in these materials and by interactively researching their developing understandings. As both teacher and researcher, I used what I learned about their understandings to support their efforts to extend the body of experimental knowledge they were developing. Development is evident in experimental details. Initially, by hand-holding, they light a bulb with a wire and battery. Later, in soldering connections, they wonder about the bulb's internal structure. They research thoughts about this through dissecting a bulb -- and lighting its exposed filament. Such experimenting changed thinking: from imagining sequential loops, to questioning electrical contacts, to inferring circuital paths.

  3. Transgressive first clinical experiences

    DEFF Research Database (Denmark)

    Jensen, Carsten Juul; Jeppesen, Lise Kofoed; Drachmann, Merete

    2014-01-01

    . The nursing students’ learning seems to be oriented towards socialization in the clinic as a workplace. This means that the nursing students seek to deal with overwhelming experiences concerning the naked bodies of patients and death, useful application of theoretical knowledge, the path from novice......This Study seeks to comprehend learning experiences of nursing students during their first clinical in-service placement. This Paper is part of a longitudinal development project interviewing the Student Nurse after each one of the five clinical in-service placements and then one year after...... graduation as a Nurse. The Study has a qualitative methodology, inspired by Michael Eraut’s thoughts on learning in the workplace. When the workplace perspective is applied, learning seems to be concentrated on actual situations which the Learner is in, in contrast to employing constructed concepts...

  4. The LDMX Experiment

    Directory of Open Access Journals (Sweden)

    Mans Jeremiah

    2017-01-01

    Full Text Available The thermal-relic mechanism for the production of dark-matter in the early universe, combined with the precision measurements of the cosmic microwave background and the lack of observation of dark matter at the LHC, motivates the search for dark matter in the mass range between 1 MeV and 1 GeV. We describe the concept for the Light Dark Matter Experiment (LDMX, which could carry out such a search using the missing-momentum technique. The experiment would utilize a unique high-rate, low-current electron beam with an energy between 4 GeV and 10 GeV, and would have sensitivity to the thermal-relic hypothesis over a wide range of masses below 1 GeV.

  5. Engaging the Shopping Experience

    DEFF Research Database (Denmark)

    Sørensen, Sanne Dollerup

    The revenues in brick-and-mortar stores have declined in the last decade, not least due to competition from online shopping. This thesis investigates how traditional stores might use principles from experience design to reverse this tendency. Brick-and-mortar stores are very important...... research, experience design, literary theory, the history and sociology of shopping. The method used is observation studies of cases that more or less successfully have been able to engage customers. This has resulted in an in-depth study of one such store and a typology of different types of engaging...... the interest in brick-and-mortar stores by engaging the customers emotionally. This thesis suggests that using insights from Possible World Theory in designing stores is one way to do this. Theoretically the thesis is interdisciplinary by drawing on knowledge from a wide spectrum of fields such as consumer...

  6. Future flavour physics experiments

    Science.gov (United States)

    2015-01-01

    The current status of flavour physics and the prospects for present and future experiments will be reviewed. Measurements in B‐physics, in which sensitive probes of new physics are the CKM angle γ, the Bs mixing phase ϕs, and the branching ratios of the rare decays B(s)0→μ+μ− , will be highlighted. Topics in charm and kaon physics, in which the measurements of ACP and the branching ratios of the rare decays K→πνν¯ are key measurements, will be discussed. Finally the complementarity of the future heavy flavour experiments, the LHCb upgrade and Belle‐II, will be summarised. PMID:26877543

  7. Commissioning the CMS experiment

    CERN Document Server

    Camporesi, T.

    2008-01-01

    The CMS experiment is getting ready to take data at the LHC accelerator at CERN. Due to late delivery of the experimental caverns the detector had to be pre-assembled on the surface and lowered in large segments. This has constrained the commissioning strategy of the experiment. Global commissioning has started in Spring of 2007 and has progressed in parallel with the construction and assembly of detector and services underground. This paper describes the strategy adopted in order to commission components of the system in incremental steps in order to be ready to accept collisions from LHC with a well debugged and understood system, including the detector, acquisition system, trigger, software, computing and data shipping.

  8. Digital Heritage Experiences

    DEFF Research Database (Denmark)

    Munar, Ana Maria; Ooi, Can-Seng

    The evolution of the Web and the expansion of social media are transforming our heritage experiences. Social media offer an innovative element to personal travel reflections by providing digital global platforms on which tourists can create and publish their travel stories. Social media transform...... the traditional creative processes, distribution mechanisms and consumption patterns of these experiences. This study provides insight on how personal heritage moments are constructed, digitalized and shared. The methodological perspective adopted draws on a constructivist epistemology (Markham 2004......) and netnography (Kozinets, 2002). The social media platform analysed is TripAdvisor, which is the largest networking site focusing on tourism and travel. Study findings indicate that while heritage sites tend to promote their uniqueness and the cultural value of their products, tourists are just as concerned...

  9. New Experiments with Antiprotons

    Science.gov (United States)

    Kaplan, D. M.

    2011-12-01

    Fermilab operates the world's most intense antiproton source. Recently proposed experiments can use those antiprotons either parasitically during Teva-tron Collider running or after the Tevatron Collider finishes in about 2011. For example, the annihilation of 8 GeV antiprotons might make the world's most intense source of tagged D0 mesons, and thus the best near-term opportunity to study charm mixing and search for new physics via its CP-violation signature. Other possible precision measurements include properties of the X(3872) and the charmonium system. An experiment using a Penning trap and an atom interferometer could make the world's first measurement of the gravitational force on antimatter. These and other potential measurements using antiprotons could yield a broad physics program at Fermilab in the post-Tevatron era.

  10. Muon science experiments

    International Nuclear Information System (INIS)

    Nishiyama, Kusuo

    2001-01-01

    Muon experimental facility is in the planning stage as a part of the high intensity proton accelerator project of KEK and JAERI. Outline of muon experimental facility and physical experiments are described. There are five kinds of beam channels such as superconducting solenoid, surface muon, ultra-slow muon, high momentum muon and ultra-high intensity muon. The μSR method by positive electric charge muon makes possible to study antiferromagnet, spin glass, muon spin high-frequency resonance and paramagnetic shift. The positive electric charge muon is one of hydrogen isotopes. Accordingly, the quantum diffusion experiments of metals, semiconductor and insulator are carried out by the isotope effect. Development of muon catalyzed fusion by negative electric charge muon is one of problems of this facility. It can be applied to chemical reaction and non-destructive analysis. An illustration of the history of muon science is shown. (S.Y.)

  11. Quantum Gravity Experiments

    Directory of Open Access Journals (Sweden)

    Cahill R. T.

    2015-10-01

    Full Text Available A new quantum gravity experiment is reported with the data confirming the generali- sation of the Schrödinger equation to include the interaction of the wave function with dynamical space. Dynamical space turbulence, via this interaction process, raises and lowers the energy of the electron wave function, which is detected by observing conse- quent variations in the electron quantum barrier tunnelling rate in reverse-biased Zener diodes. This process has previously been reported and enabled the measurement of the speed of the dynamical space flow, which is consistent with numerous other detection experiments. The interaction process is dependent on the angle between the dynamical space flow velocity and the direction of the electron flow in the diode, and this depen- dence is experimentally demonstrated. This interaction process explains gravity as an emergent quantum process, so unifying quantum phenomena and gravity. Gravitational waves are easily detected.

  12. Microwave Tokamak Experiment

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    The Microwave Tokamak Experiment, now under construction at the Laboratory, will use microwave heating from a free-electron laser. The intense microwave pulses will be injected into the tokamak to realize several goals, including a demonstration of the effects of localized heat deposition within magnetically confined plasma, a better understanding of energy confinement in tokamaks, and use of the new free-electron laser technology for plasma heating. The experiment, soon to be operational, provides an opportunity to study dense plasmas heated by powers unprecedented in the electron-cyclotron frequency range required by the especially high magnetic fields used with the MTX and needed for reactors. 1 references, 5 figures, 3 tables

  13. Copenhagen Sonic Experience Map

    DEFF Research Database (Denmark)

    Kreutzfeldt, Jacob

    2011-01-01

    In the wake of present European interest for mapping urban noise, it seems increasingly relevant to investigate the multiple ways in which sound intersects with the everyday experiences of urban citizens. Focusing on the polluting effects of infrastructural noise, the EU-initiated project...... of assessment and management of environmental noise brings forth the disturbing and potentially damaging effect of environmental sound.1 But as maps of coloured streets start to circulate, and real estate prices drop in designated blue and red areas,2 it is worth remembering that sound itself is not a killer....... Most of the time sound is a trivial part of everyday life involved in interactions, experiences, atmospheres, actions, etc. Although trivial, the role of the aural in the urban life world is more complex than what is suggested by sound level maps, and as such it may be a vital part of urbanity itself...

  14. Gross decontamination experiment report

    Energy Technology Data Exchange (ETDEWEB)

    Mason, R.; Kinney, K.; Dettorre, J.; Gilbert, V.

    1983-07-01

    A Gross Decontamination Experiment was conducted on various levels and surfaces of the TMI - Unit 2 reactor building in March 1982. The polar crane, D-rings, missile shields, refueling canals, refueling bridges, equipment, and elevations 305' and 347'-6'' were flushed with low pressure water. Additionally, floor surfaces on elevation 305' and floor surfaces and major pieces of equipment on elevation 347'-6'' were sprayed with high pressure water. Selective surfaces were decontaminated with a mechanical scrubber and chemicals. Strippable coating was tested and evaluated on equipment and floor surfaces. The effectiveness, efficiency, and safety of several decontamination techniques were established for the large, complex decontamination effort. Various decontamination equipment was evaluated and its effectiveness was documented. Decontamination training and procedures were documented and evaluated, as were the support system and organization for the experiment.

  15. Gross decontamination experiment report

    International Nuclear Information System (INIS)

    Mason, R.; Kinney, K.; Dettorre, J.; Gilbert, V.

    1983-07-01

    A Gross Decontamination Experiment was conducted on various levels and surfaces of the TMI - Unit 2 reactor building in March 1982. The polar crane, D-rings, missile shields, refueling canals, refueling bridges, equipment, and elevations 305' and 347'-6'' were flushed with low pressure water. Additionally, floor surfaces on elevation 305' and floor surfaces and major pieces of equipment on elevation 347'-6'' were sprayed with high pressure water. Selective surfaces were decontaminated with a mechanical scrubber and chemicals. Strippable coating was tested and evaluated on equipment and floor surfaces. The effectiveness, efficiency, and safety of several decontamination techniques were established for the large, complex decontamination effort. Various decontamination equipment was evaluated and its effectiveness was documented. Decontamination training and procedures were documented and evaluated, as were the support system and organization for the experiment

  16. Experiments around I-8

    CERN Multimedia

    CERN PhotoLab

    1975-01-01

    The lithium transition-radiation detectors and the large liquid argon calorimeters of experiment R806T are shown above and below the intersection at I-8 (Brookhaven-CERN-Saclay-Syracuse-Yale Collaboration, Study of large transverse momentum phenomena by electron and photon detection). At 90 deg to the intersecting beams are the monitoring proporional chambers of experiment R805 (Measurement of real to imaginary ratio of forward scattering amplitude - Coulomb interference - by the CERN-Rome Collaboration). Left and right of the intersection one sees, symmetrically placed around the interaction region, the large scintillation counters hodoscopes used by R801 (Pisa-Stony Brook Collaboration) to measure the pp total cross section and the features of inelastic collisions.

  17. The MOZART experiment

    International Nuclear Information System (INIS)

    Briec, M.; Abassin, J.J.; Masson, M.; Johnson, C.E.; Roux, N.

    1989-01-01

    The MOZART experiment was carried out within the framework of the BEATRIX program, as part of the Commissariat a l'Energie Atomique contribution to this international collaboration program. This experiment was run during 45 days in the MELUSIN reactor at Grenoble. Tested ceramics were Li 2 O and LiAlO 2 from Japan, Li 2 ZrO 3 from USA, LiAlO 2 from CEA. Influence of parameters such as temperature, sweep gas composition was investigated. Tritium residence times as a function of temperature were calculated. The comparison of the tritium release performance of the three ceramic breeders was made. This investigation has first evidenced the very good tritium release characteristics of Li 2 ZrO 3 especially at low temperatures. (author). 7 refs.; 5 figs.; 3 tabs

  18. The Vinca dosimetry experiment

    International Nuclear Information System (INIS)

    1962-03-01

    On 15 October 1958 there occurred a very brief uncontrolled run of the zero-power reactor at the Boris Kidric Institute of Nuclear Science, Vinca, near Belgrade, Yugoslavia. During this run six persons received various doses of radiation. They were subsequently given medical treatment of a novel kind at the Curie Hospital, Paris. In atomic energy operations to date, very few accidents involving excessive radiation exposure to human beings have occurred. In fact, the cases of acute radiation injury are limited to about 30 known high exposures, few of which were in the lethal or near-lethal range. Since direct experiment to determine the effects of ionizing radiation on man is unacceptable, information on these effects has to be based on a consideration of data relating to accidental exposures, viewed in the light of the much more extensive data obtained from experiments on animals. Therefore, any direct information on the effects of radiation on humans is very valuable. The international dosimetry project described in this report was carried out at Vinca, Yugoslavia, under the auspices of the International Atomic Energy Agency to determine the precise amount of radiation to which the persons had been exposed during the accident. These dosimetry data, together with the record of the carefully observed clinical effects, are of importance both for the scientific study of radiation effects on man and for the development of methods of therapy. The experiment and measurements were carried out at the end of April 1960. The project formed part of the Agency's research programme in the field of health and safety. The results of the experiment are made available through this report to all Member States

  19. CANDU operating experience

    International Nuclear Information System (INIS)

    McConnell, L.G.; Woodhead, L.W.; Fanjoy, G.R.

    1982-09-01

    The CANDU (CANada Deuterium Uranium) Pressurized Heavy Water (PHW) type of nuclear-electric generating station was developed jointly by Atomic Energy of Canada Limited and Ontario Hydro. This paper summarizes Ontario Hydro's operating experience using the CANDU-PHW system, with a focus on the operating performance and costs, reliability of system components, and nuclear safety considerations to both the workers and the public

  20. submitter LHC experiments

    CERN Document Server

    Tanaka, Shuji

    2001-01-01

    Large Hadron Collider (LHC) is under construction at the CERN Laboratory in Switzerland. Four experiments (ATLAS, CMS, LHCb, ALICE) will try to study the new physics by LHC from 2006. Its goal to explore the fundamental nature of matter and the basic forces. The PDF file of the transparency is located on http://www-atlas.kek.jp/sub/documents/lepsymp-stanaka.pdf.

  1. Delivering ideal employee experiences.

    Science.gov (United States)

    Weiss, Marjorie D; Tyink, Steve; Kubiak, Curt

    2009-05-01

    Employee-centric strategies have moved from employee satisfaction and brand awareness to employee "affinity" or "attachment." In today's marketplace, occupational health nurses understand that differentiation (i.e., the perception of uniqueness) is the direct result of superior employee interactions, which lead to better employee care, enduring employee relationships, loyal employees, and satisfied employers. What drives employees to occupational health nurse attachment? The answer is a passion for rising above the competition to create ideal employee experiences.

  2. DIRAC experiment at CERN

    CERN Document Server

    Benelli, Angela

    2012-01-01

    The precise measurements of $\\pi^+\\pi^-$ and $\\pi K$ atom lifetime allow to check the predictions of Chiral Perturbation Theory for the pion-pion s-wave scattering lengths with isospin 0 and 2 and for the pion-kaon scattering lengths with isospin 1/2 and 3/2. The DIRAC experiment with the latest results is presented together with the proposal for future investigations.

  3. The MUSE experiment

    OpenAIRE

    Downie E. J.

    2014-01-01

    The proton radius puzzle is the difference between the proton radius as measured with electron scattering and in the excitation spectrum of atomic hydrogen, and that measured with muonic hydrogen spectroscopy. The MUSE experiment seeks to resolve this puzzle by simultaneously measuring elastic electron and muon scattering on the proton, in both charge states, thereby providing new information to the puzzle. MUSE addresses issues of two-photon effects, lepton universality and, possibly, new ph...

  4. The global accounting experiment

    OpenAIRE

    Nicolas Véron

    2007-01-01

    In this essay, Nicolas Véron presents accounting standard-setting as a frontier experiment in international governance, where private initiative can succeed in solving a collective problem that nation-states could not tackle effectively. To make the adoption of International Financial Reporting Standards (IFRS) in Europe and other jurisdictions sustainable, the legitimacy of the International Accounting Standards Board has to be bolstered through significant governance changes; and their impl...

  5. The CONNIE experiment

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar-Arevalo, A.; et al.

    2016-10-19

    The CONNIE experiment uses fully depleted, high resistivity CCDs as particle detectors in an attempt to measure for the first time the Coherent Neutrino-Nucleus Elastic Scattering of antineutrinos from a nuclear reactor with silicon nuclei.This talk, given at the XV Mexican Workshop on Particles and Fields (MWPF), discussed the potential of CONNIE to perform this measurement, the installation progress at the Angra dos Reis nuclear power plant, as well as the plans for future upgrades.

  6. Holodeck-ISS Experience

    Science.gov (United States)

    Rainbolt, Phillip

    2016-01-01

    For the duration of my internship here at JSC for the summer 2016 session, the main project that I worked on dealt with hybrid reality simulations of the ISS. As an ER6 intern for the spacecraft software division, the main project that I worked alongside others was with regards to the Holodeck Virtual Reality Project, specifically with the ISS experience, with the use of the HTC Vive and controllers.

  7. The NEXT experiment

    Energy Technology Data Exchange (ETDEWEB)

    DIaz, J; Yahlali, N; Ball, M; Carcel, S; Cervera, A; Gil, A [Instituto de Fisica Corpuscular (Centro mixto UV-CSIC), Apdo. de Correos 22085, E-46071 Valencia (Spain) (Spain); Barata, J A S; Borges, F I G M; Conde, C A N; Dias, T H V T; Fernandes, L M P; Freitas, E D C [Universidade de Coimbra (Portugal); Calvo, E [Instituto de Fisica de Altas EnergIas, IFAE, Barcelona (Spain); Carmona, J M; Cebrian, S; Dafni, T; Galan, J [U. Zaragoza (Spain); Cid, X [Universidade de Santiago de Compostela (Spain); Ferrer-Ribas, E [CEA, IRFU, Saclay (France); Gil, I, E-mail: jose.diaz@uv.e [CIEMAT (Spain)

    2009-07-01

    Neutrinoless double beta decay measurements are the most promising experiments both to reveal the Majorana nature of the neutrino and to set a value for its mass. The NEXT project propose to build a High pressure Xenon TPC in the Canfranc Underground Laboratory (Huesca, Spain) to measure double-beta decay of {sup 136}Xe, both normal and neutrinoless, with a source mass of 100 kg of enriched xenon.

  8. The COMPASS experiment

    CERN Multimedia

    2006-01-01

    Artistic view of the 60 m long Common Muon and Proton Apparatus for Structure and Spectroscopy (COMPASS) experiment. COMPASS takes beams from the SPS accelerator at CERN. This beam enters from the lower left and passes through the cylindrical target solenoid. COMPASS is used to study the internal structure of hadrons (composite particles interacting via the strong force) by looking at a property called spin and a phenomenon known as glueballs.

  9. The ACE experiment

    CERN Multimedia

    Maximilien Brice

    2006-01-01

    The Antiproton Cell Experiment (ACE) as shown by Michael Holzscheiter (spokesperson), Niels Bassler (co-spokesperson) and Helge Knudsen. ACE is located on the Antiproton Decelerator (AD) at CERN. An antiproton annihilates a proton in the nucleus of a cancer cell, producing a pair of gamma rays, destroying the entire cell and some surrounding cells. Many fewer antiprotons are required in this treatment than in the equivalent proton hadron therapy, so there is less risk of healthy tissue damage.

  10. Crossed beam experiments

    International Nuclear Information System (INIS)

    Dolder, K.T.

    1976-01-01

    Many natural phenomena can only be properly understood if one has a detailed knowledge of interactions involving atoms, molecules, ions, electrons or photons. In the laboratory these processes are often studied by preparing beams of two types of particle and observing the reactions which occur when the beams intersect. Some of the more interesting of these crossed beam experiments and their results are discussed. Proposals to extend colliding beam techniques to high energy particle physics are also outlined. (author)

  11. Creating Sustainable Digital Experiences

    Directory of Open Access Journals (Sweden)

    Kozinets Robert V.

    2014-11-01

    Full Text Available Is the social media hype about being cool or about making money? For Adam Froman, the answer is easy: Marketers need to be very clear about how social media activity supports overall business strategy. Only if the digital experience fi ts into the whole customer journey will consumers become engaged and add value to the company … and only then will the social brand become cool.

  12. NRC Construction Experience

    International Nuclear Information System (INIS)

    Rasmussen, Richard

    2013-01-01

    This presentation deals with the domestic and international construction experience sources. From the domestic (USA) point of view, the sources are event notifications, non-compliance reports, inspection reports, etc. Internationally, the presentation highlights the following sources: IRS and ConEx reports, Nuclear Events Web Based System (NEWS), bilateral agreements, MDEP, etc. It also mentions and describes briefly reported on concrete, rebar, fabrication and digital issues

  13. Relay mirror experiment

    Science.gov (United States)

    Begley, David L.

    1996-04-01

    Originating out of a SDIO-funded, Phase 1 study effort, two ground systems and an orbiting EO payload/spacecraft were the primary equipment for the RME. The RME was originally conceived to be a shuttle deployed experiment. Shortly after program start, the Challenger disaster occurred, with the promise of extensive delays. A completely new space segment was to be designed incorporating a free-flying spacecraft. During the midphase of the program, a variety of launch vehicles were envisioned to replace the shuttle, requiring the BASD team to design accommodations for Delta, Atlas, and Titan, with a Delta launch being the final solution. The ground systems tracked the spacecraft and illuminated it with green and blue beacon lasers. The Payload Experiment Package (PEP) housed the bisection tracker, a key innovation central to the experiment. The bisection tracker acquired both beacons and controlled steerable mirrors to accomplish fine tracking of the two cooperative beacons. In the process, the relay mirror was precisely positioned to enable a successful relay of a third infrared laser between the two ground sites via the orbiting spacecraft. Many of the key technologies employed in the PEP were originally developed for Ball laser communications research and development programs and other laser pointing efforts. The WAVE sensor package, built by ATA and integrated by Ball, measured the vibrations of the optical base structure on which it was mounted. These spacecraft vibration data are critical to the accurate pointing of space laser communication terminals.

  14. Experimenting with practice

    DEFF Research Database (Denmark)

    Knudsen, Hanne; Adriansen, Hanne Kirstine

    2016-01-01

    Abstract Purpose Teaching executive courses always raises the challenge of how to deal with the tension between theory and practice. The present chapter analyses the use of experiments in practice as a pedagogical approach to deal with this tension in Master’s programmes. Design/methodology/appro......Abstract Purpose Teaching executive courses always raises the challenge of how to deal with the tension between theory and practice. The present chapter analyses the use of experiments in practice as a pedagogical approach to deal with this tension in Master’s programmes. Design...... creates a liminal zone with hybrid characteristics. Research limitations/implications The chapter provides new conceptualizations of the tensions between theory and practice based on our experiences from one degree programme. It would have been interesting to study other executive programmes and which....... It does not solve the tension between theory and practice but creates new challenges, potentialities, dilemmas and insights. Originality/value We suggest using ‘monstrosity’ as an umbrella term for ‘hybrid’ and ‘liminality’ of the complex relations that are at play in further education of practitioners...

  15. Sequential Design of Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Anderson-Cook, Christine Michaela [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-06-30

    A sequential design of experiments strategy is being developed and implemented that allows for adaptive learning based on incoming results as the experiment is being run. The plan is to incorporate these strategies for the NCCC and TCM experimental campaigns to be run in the coming months. This strategy for experimentation has the advantages of allowing new data collected during the experiment to inform future experimental runs based on their projected utility for a particular goal. For example, the current effort for the MEA capture system at NCCC plans to focus on maximally improving the quality of prediction of CO2 capture efficiency as measured by the width of the confidence interval for the underlying response surface that is modeled as a function of 1) Flue Gas Flowrate [1000-3000] kg/hr; 2) CO2 weight fraction [0.125-0.175]; 3) Lean solvent loading [0.1-0.3], and; 4) Lean solvent flowrate [3000-12000] kg/hr.

  16. Shock tube Multiphase Experiments

    Science.gov (United States)

    Middlebrooks, John; Allen, Roy; Paudel, Manoj; Young, Calvin; Musick, Ben; McFarland, Jacob

    2017-11-01

    Shock driven multiphase instabilities (SDMI) are unique physical phenomena that have far-reaching practical applications in engineering and science. The instability is present in high energy explosions, scramjet combustors, and supernovae events. The SDMI arises when a multiphase interface is impulsively accelerated by the passage of a shockwave. It is similar in development to the Richtmyer-Meshkov (RM) instability however, particle-to-gas coupling is the driving mechanism of the SDMI. As particle effects such as lag and phase change become more prominent, the SDMI's development begins to significantly deviate from the RM instability. We have developed an experiment for studying the SDMI in our shock tube facility. In our experiments, a multiphase interface is created using a laminar jet and flowed into the shock tube where it is accelerated by the passage of a planar shockwave. The interface development is captured using CCD cameras synchronized with planar laser illumination. This talk will give an overview of new experiments conducted to examine the development of a shocked cylindrical multiphase interface. The effects of Atwood number, particle size, and a second acceleration (reshock) of the interface will be discussed.

  17. Hyperon Beam Experiment

    CERN Multimedia

    2002-01-01

    The experiment WA89 uses the upgraded Omega facility together with a hyperon beam installed at the end of the H1 beamline. The beam can deliver 2~10$ ^{5} \\% Sigma ^- $ per machine burst at 330 GeV/c with a background of 5 10$ ^{5} \\% \\pi ^- $. \\\\ \\\\ The goals of the experiment are: observation of charmed particles, mainly the charmed-strange baryons and measurements of their production in the kinematical range x$ _{F} $~$>$~0.2, and their decay properties, a search for exotic states such as U(3100) observed in the previous CERN hyperon beam experiment WA62, measurements of hyperon polarization and production properties. \\\\ \\\\ A vertex detector consisting of 24 silicon microstrip planes with 25~$\\mu$m pitch and 6~planes with 50~$\\mu$m pitch provides track measurements of sufficient accuracy to identify the decays of short living charmed particles and measure their lifetimes. A RICH detector provides good $\\pi$/K separation for momenta up to 100~GeV/c and $\\pi$/p separation up to 150~GeV/c. Photons are detecte...

  18. Measuring the User Experience

    Directory of Open Access Journals (Sweden)

    Harry B. Santoso

    2016-01-01

    Full Text Available The aim of the current study is to develop an adapted version of User Experience Questionnaire (UEQ and evaluate a learning management system. Although there is a growing interest on User Experience, there are still limited resources (i.e. measurement tools or questionnaires available to measure user experience of any products, especially learning management systems. Two hundreds and thirteen computer science students participated and completed the adapted version of UEQ. In the study, the researchers used a learning management system named Student Centered e-Learning Environment (SCELE. Several types of learning materials are posted in SCELE such as audio files, simulations, PowerPoint slides, multimedia contents, and webpage links. Most of the lecturers use discussion forums in their courses to encourage students to participate in active learning setting. Staff and lecturers sometimes post academic-related announcements on the SCELE homepage. Two hundred thirteen students enrolled in Computer Science program were invited to evaluate the SCELE. This study will benefit UX practitioners, HCI educators, program and center of learning resources administrators, and learning management system developers. Findings of the present study may also be valuable for universities and high schools which are using computer-based learning environments.

  19. Tango for experiment control

    International Nuclear Information System (INIS)

    Meyer, J.; Claustre, L.; Petitdemange, S.; Svensson, O.; Götz, A.; Coutinho, T.; Klora, J.; Picca, F.; Ounsy, M.; Buteau, A.

    2012-01-01

    The Tango control system framework allows you to control an accelerator complex as well as single equipment. The framework contains the communication bus with the standard communication modes (synchronous, asynchronous, event driven) as well as the basic hardware access modules, GUI tools and development kits, bindings to commercial products (LabView, Matlab, IgorPro) and services (administration, archiving, access control) to set up a control system. Tango was mainly developed by several synchrotron light sources that have to support not only the accelerator complex but also a lot of experimental end stations. For synchrotron experiments we have to control the whole process from basic hardware access over data taking to data analysis. This paper describes in the first part the special features of Tango allowing flexible experiment control. The dynamic configuration, the rapid hardware interface development and the sequencing and scanning framework are some examples. The second part gives an overview of some packages developed in the Tango community for experiment control: A HKL library for diffraction computation and diffractometer control, a library to control 2D detectors and a data analysis workbench with workflow engine for on-line and off-line data analysis. These packages are not part of Tango and can be used with other control systems. (author)

  20. AGS experiments: 1990, 1991, 1992

    International Nuclear Information System (INIS)

    Depken, J.C.

    1993-04-01

    This report contains a description of the following: AGS Experimental Area - High Energy Physics FY 1993 and Heavy Ion Physics FY 1993; Table of Beam Parameters and Fluxes; Experiment Schedule ''as run''; Proposed 1993 Schedule; A listing of experiments by number; Two-page summaries of each experiment begin here, also ordered by number; Publications of AGS Experiments; and List of AGS Experimenters

  1. AGS Experiments: 1989, 1990, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.

    1992-02-01

    This report contains: Experimental areas layout; table of beam parameters and fluxes; experiment schedule as run''; proposed 1992 schedule; a listing of experiments by number; two-page summaries of each experiment begin here, also ordered by number; publications of AGS Experiments begin here; and list of AGS Experimenters begins here.

  2. AGS Experiments: 1989, 1990, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Depken, J.C.

    1992-02-01

    This report contains: Experimental areas layout; table of beam parameters and fluxes; experiment schedule ``as run``; proposed 1992 schedule; a listing of experiments by number; two-page summaries of each experiment begin here, also ordered by number; publications of AGS Experiments begin here; and list of AGS Experimenters begins here.

  3. Supporting planning and conducting experiments

    NARCIS (Netherlands)

    van Riesen, Siswa; Gijlers, Aaltje H.; Anjewierden, Anjo Allert; de Jong, Anthonius J.M.; Looi, Chee-Kit; Polman, Joseph; Cress, Ulrike; Reimann, Peter

    2016-01-01

    In inquiry learning learners design and conduct experiments. Learners experience difficulties with the involved processes and need guidance to design useful experiments. To guide students in this we created a configurable experiment design tool that is usable in multiple domains. The tool was tested

  4. Urban Experiments and Concrete Utopias

    DEFF Research Database (Denmark)

    Andersson, Lasse

    2009-01-01

    The paper explores how concrete urban experiments can challenge the pecuniary version of the experience city and stimulate a locally rooted and democratic version of an experience based city using heterotopias and concrete utopias as the link between top down planning and bottom up experiments...

  5. AGS Experiments: 1989, 1990, 1991

    International Nuclear Information System (INIS)

    Depken, J.C.

    1992-02-01

    This report contains: Experimental areas layout; table of beam parameters and fluxes; experiment schedule ''as run''; proposed 1992 schedule; a listing of experiments by number; two-page summaries of each experiment begin here, also ordered by number; publications of AGS Experiments begin here; and list of AGS Experimenters begins here

  6. AGS experiments - 1982, 1983, 1984

    International Nuclear Information System (INIS)

    Bunce, G.

    1983-01-01

    The report contains layouts of experimental areas, a table of beam parameters and fluxes, the experiment schedule as run, the experiment long range schedule, a listing of experiments by number, and a section of two-page summaries of each experiment

  7. Electronics for LHC experiments

    International Nuclear Information System (INIS)

    Bourgeois, Francois

    1995-01-01

    Full text: A major effort is being mounted to prepare the way handling the high interaction rates expected from CERN's new LHC proton-proton collider (see, for example, November, page 6). September saw the First Workshop on Electronics for LHC Experiments, organized by Lisbon's Particle Physics Instrumentation Laboratory (LIP) on behalf of CERN's LHC Electronics Review Board (LERB - March, page 2). Its purpose was not only for the LERB to have a thorough review of ongoing activities, but also to promote cross fertilization in the engineering community involved in electronics design for LHC experiments. The Workshop gathered 187 physicists and engineers from 20 countries including USA and Japan. The meeting comprised six sessions and 82 talks, with special focus on radiation-hard microelectronic processes, electronics for tracking, calorimetry and muon detectors, optoelectronics, trigger and data acquisition systems. Each topic was introduced by an invited speaker who reviewed the requirements set by the particular detector technology at LHC. At the end of each session, panel discussions were chaired by each invited speaker. Representatives from four major integrated circuit manufacturers covered advanced radiation hard processes. Two talks highlighted the importance of obsolescence and quality systems in the long-lived and demanding environment of LHC. The Workshop identified areas and encouraged efforts for rationalization and common developments within and between the different detector groups. As a result, it will also help ensure the reliability and the long term maintainability of installed equipment. The proceedings of the Workshop are available from LIP Lisbon*. The LERB Workshop on Electronics for LHC Experiments will become a regular event, with the second taking place in Hungary, by Lake Balaton, from 23-27 September 1996. The Hungarian institutes KFKIRMKI have taken up the challenge of being as successful as LIP Lisbon in the organization

  8. Experience the Moon

    Science.gov (United States)

    Ortiz-Gil, A.; Benacchio, L.; Boccato, C.

    2011-10-01

    The Moon is, together with the Sun, the very first astronomical object that we experience in our life. As this is an exclusively visual experience, people with visual impairments need a different mode to experience it too. This statement is especially true when events, such as more and more frequent public observations of sky, take place. This is the reason why we are preparing a special package for visual impaired people containing three brand new items: 1. a tactile 3D Moon sphere in Braille with its paper key in Braille. To produce it we used imaging data obtained by NASA's mission Clementine, along with free image processing and 3D rendering software. In order to build the 3D small scale model funding by Europlanet and the Italian Ministry for Research have been used. 2. a multilingual web site for visually impaired users of all ages, on basic astronomy together with an indepth box about the Moon; 3. a book in Braille with the same content of the Web site mentioned above. All the items will be developed with the collaboration of visually impaired people that will check each step of the project and support their comments and criticism to improve it. We are going to test this package during the next International Observe the Moon Night event. After a first testing phase we'll collect all the feedback data in order to give an effective form to the package. Finally the Moon package could be delivered to all those who will demand it for outreach or educational goals.

  9. 2169 steel waveform experiments.

    Energy Technology Data Exchange (ETDEWEB)

    Furnish, Michael David; Alexander, C. Scott; Reinhart, William Dodd; Brown, Justin L.

    2012-11-01

    In support of LLNL efforts to develop multiscale models of a variety of materials, we have performed a set of eight gas gun impact experiments on 2169 steel (21% Cr, 6% Ni, 9% Mn, balance predominantly Fe). These experiments provided carefully controlled shock, reshock and release velocimetry data, with initial shock stresses ranging from 10 to 50 GPa (particle velocities from 0.25 to 1.05 km/s). Both windowed and free-surface measurements were included in this experiment set to increase the utility of the data set, as were samples ranging in thickness from 1 to 5 mm. Target physical phenomena included the elastic/plastic transition (Hugoniot elastic limit), the Hugoniot, any phase transition phenomena, and the release path (windowed and free-surface). The Hugoniot was found to be nearly linear, with no indications of the Fe phase transition. Releases were non-hysteretic, and relatively consistent between 3- and 5-mmthick samples (the 3 mm samples giving slightly lower wavespeeds on release). Reshock tests with explosively welded impactors produced clean results; those with glue bonds showed transient releases prior to the arrival of the reshock, reducing their usefulness for deriving strength information. The free-surface samples, which were steps on a single piece of steel, showed lower wavespeeds for thin (1 mm) samples than for thicker (2 or 4 mm) samples. A configuration used for the last three shots allows release information to be determined from these free surface samples. The sample strength appears to increase with stress from ~1 GPa to ~ 3 GPa over this range, consistent with other recent work but about 40% above the Steinberg model.

  10. Southeast Regional Experiment Station

    Science.gov (United States)

    1994-08-01

    This is the final report of the Southeast Regional Experiment Station project. The Florida Solar Energy Center (FSEC), a research institute of the University of Central Florida (UCF), has operated the Southeast Regional Experiment Station (SE RES) for the US Department of Energy (DOE) since September 1982. Sandia National Laboratories, Albuquerque (SNLA) provides technical program direction for both the SE RES and the Southwest Regional Experiment Station (SW RES) located at the Southwest Technology Development Institute at Las Cruces, New Mexico. This cooperative effort serves a critical role in the national photovoltaic program by conducting system evaluations, design assistance and technology transfer to enhance the cost-effective utilization and development of photovoltaic technology. Initially, the research focus of the SE RES program centered on utility-connected PV systems and associated issues. In 1987, the SE RES began evaluating amorphous silicon (a-Si) thin-film PV modules for application in utility-interactive systems. Stand-alone PV systems began receiving increased emphasis at the SE RES in 1986. Research projects were initiated that involved evaluation of vaccine refrigeration, water pumping and other stand-alone power systems. The results of this work have led to design optimization techniques and procedures for the sizing and modeling of PV water pumping systems. Later recent research at the SE RES included test and evaluation of batteries and charge controllers for stand-alone PV system applications. The SE RES project provided the foundation on which FSEC achieved national recognition for its expertise in PV systems research and related technology transfer programs. These synergistic products of the SE RES illustrate the high visibility and contributions the FSEC PV program offers to the DOE.

  11. Simulation - modeling - experiment

    International Nuclear Information System (INIS)

    2004-01-01

    After two workshops held in 2001 on the same topics, and in order to make a status of the advances in the domain of simulation and measurements, the main goals proposed for this workshop are: the presentation of the state-of-the-art of tools, methods and experiments in the domains of interest of the Gedepeon research group, the exchange of information about the possibilities of use of computer codes and facilities, about the understanding of physical and chemical phenomena, and about development and experiment needs. This document gathers 18 presentations (slides) among the 19 given at this workshop and dealing with: the deterministic and stochastic codes in reactor physics (Rimpault G.); MURE: an evolution code coupled with MCNP (Meplan O.); neutronic calculation of future reactors at EdF (Lecarpentier D.); advance status of the MCNP/TRIO-U neutronic/thermal-hydraulics coupling (Nuttin A.); the FLICA4/TRIPOLI4 thermal-hydraulics/neutronics coupling (Aniel S.); methods of disturbances and sensitivity analysis of nuclear data in reactor physics, application to VENUS-2 experimental reactor (Bidaud A.); modeling for the reliability improvement of an ADS accelerator (Biarotte J.L.); residual gas compensation of the space charge of intense beams (Ben Ismail A.); experimental determination and numerical modeling of phase equilibrium diagrams of interest in nuclear applications (Gachon J.C.); modeling of irradiation effects (Barbu A.); elastic limit and irradiation damage in Fe-Cr alloys: simulation and experiment (Pontikis V.); experimental measurements of spallation residues, comparison with Monte-Carlo simulation codes (Fallot M.); the spallation target-reactor coupling (Rimpault G.); tools and data (Grouiller J.P.); models in high energy transport codes: status and perspective (Leray S.); other ways of investigation for spallation (Audoin L.); neutrons and light particles production at intermediate energies (20-200 MeV) with iron, lead and uranium targets (Le Colley F

  12. Operating experience: safety perspective

    International Nuclear Information System (INIS)

    Piplani, Vivek; Krishnamurthy, P.R.; Kumar, Neeraj; Upadhyay, Devendra

    2015-01-01

    Operating Experience (OE) provides valuable information for improving NPP safety. This may include events, precursors, deviations, deficiencies, problems, new insights to safety, good practices, lessons and corrective actions. As per INSAG-10, an OE program caters as a fundamental means for enhancing the defence-in-depth at NPPs and hence should be viewed as ‘Continuous Safety Performance Improvement Tool’. The ‘Convention on Nuclear Safety’ also recognizes the OE as a tool of high importance for enhancing the NPP safety and its Article 19 mandates each contracting party to establish an effective OE program at operating NPPs. The lessons drawn from major accidents at Three Mile Island, Chernobyl and Fukushima Daiichi NPPs had prompted nuclear stalwarts to change their safety perspective towards NPPs and to frame sound policies on issues like safety culture, severe accident prevention and mitigation. An effective OE program, besides correcting current/potential problems, help in proactively improving the NPP design, operating and maintenance procedures, practices, training, etc., and thus plays vital role in ensuring safe and efficient operation of NPPs. Further it enhances knowledge with regard to equipment operating characteristics, system performance trends and provides data for quantitative and qualitative safety analysis. Besides all above, an OE program inculcates a learning culture in the organisation and thus helps in continuously enhancing the expertise, technical competency and knowledge base of its staff. Nuclear and Radiation Facilities in India are regulated by Atomic Energy Regulatory Board (AERB). Operating Plants Safety Division (OPSD) of AERB is involved in managing operating experience activities. This paper provides insights about the operating experience program of OPSD, AERB (including its on-line data base namely OPSD STAR) and its utilisation in improving the regulations and safety at Indian NPPs/projects. (author)

  13. Supersymmetry shaken by experiment

    International Nuclear Information System (INIS)

    Glavieux, Vincent

    2012-01-01

    The author comments how experiments performed within the CERN large hadron collider (LHC) may bring answers to the issue of the existence of supersymmetrical particles, i.e. the fact that a super-particle would be associated with each particle according to the ideas of Pierre Fayet, and more particularly the relationship between fermions and bosons. The theoretical background is presented as well as the different tested models: the GMSB (gauge mediated supersymmetry breaking) and the mSugra (minimal supergravity) models. Since 2009, if researchers actually identified all known particles, they could not find any trace of superparticles. This may put the models into question again

  14. Experience City.DK

    DEFF Research Database (Denmark)

    Marling, Gitte; Kiib, Hans; Jensen, Ole B.

    om en stribe af kulturelle begivenheder. Kulturnætter, karneval, festuger og events med i udgangspunkt i så forskellige temaer som historie, poesi, lys, naturvidenskab og musik mv. Der er tale om en "kulturel podning af byen" - både aktivitesmæssigt, fysisk og arkitektonisk som gør, at de centrale...... bydele omtales som "oplevelsesbyen". Den kulturelle podning stiller krav til de fysiske omgivelser, til arkitekturen og til design af byrum. Experience City.DK undersøger betingelser for og konsekvenser af nye hybride kulturprojekter og performative byrum i danske byer....

  15. Survey of Tokamak experiments

    International Nuclear Information System (INIS)

    Bickerton, R.J.

    1977-01-01

    The survey covers the following topics:- Introduction and history of tokamak research; review of tokamak apparatus, existing and planned; remarks on measurement techniques and their limitations; main results in terms of electron and ion temperatures, plasma density, containment times, etc. Empirical scaling; range of operating densities; impurities, origin, behaviour and control (including divertors); data on fluctuations and instabilities in tokamak plasmas; data on disruptive instabilities; experiments on shaped cross-sections; present experimental evidence on β limits; auxiliary heating; experimental and theoretical problems for the future. (author)

  16. Installation for rewetting experiments

    International Nuclear Information System (INIS)

    Rezende, H.C.; Ladeira, L.C.D.

    1986-03-01

    A test facility for rewetting experiments (ITR), has been erected at the Thermalhydraulics Laboratory of Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), with the objective of performing investigation of basic phenomena that occur during the reflood phase of a Loss of Coolant Accident (LOCA), in a Pressurized Water Reactor (PWR), utilizing tubular and annular test sections. The mechanical aspects of the facility, its power supply system and its instrumentation are described. The results of the calibration of the instruments and the description of two typical testes performed to verify the operational conditions are presented. A comparison with calculations using a computer code is also presented. (Author) [pt

  17. Double Chooz experiment

    International Nuclear Information System (INIS)

    Palomares, C.

    2009-01-01

    Double Chooz will use two identical detectors at different distances from the Chooz nuclear power station to search for a non-vanishing value of θ 13 , and, hopefully, to open the way to experiments aspiring to discover CP violation in the leptonic sector. The far detector is expected to be operative by the end of 2009. Installation of the near detector will occur in 2010. Double Chooz has the capacity to exclude sin 2 (2θ 13 ) 31 2 = 2.5 x 10 -3 eV 2 with three years of data running both near and far detectors. (author)

  18. VVER ballooning experiments

    International Nuclear Information System (INIS)

    Gyoeri, Cs.; Hozer, Z.; Maroti, L.; Matus, L.

    1998-01-01

    A series of ballooning experiments was performed at the KFKI-AEKI in order to compare the mechanical behaviour and strength of Zircaloy-4 and Zr1%Nb claddings. The effects of temperature, oxidation and iodine absorption on deformation and burst pressure was investigated in almost 100 biaxial tests. Numerical post-test analyses have also been performed with the stand-alone fuel module of the French CATHARE code and the US fuel behaviour code FRAP-T6. Comparing the experimental and the analytical results, relevant differences of high temperature strength due to different α-β phase transition temperature were revealed between the investigated cladding materials. (author)

  19. The European experience.

    Science.gov (United States)

    Roels, Leo; Rahmel, Axel

    2011-04-01

    This mini-review on European experiences with tackling the problem of organ shortage for transplantation was based on a literature review of predominantly European publications dealing with the issue of organ donation from deceased donors. The authors tried to identify the most significant factors that have demonstrated to impact on donation rates from deceased donors and subsequent transplant successes. These factors include legislative measures (national laws and European Directives), optimization of the donation process, use of expanded criteria donors, innovative preservation and surgical techniques, organizational efforts, and improved allocation algorithms. © 2011 The Authors. Transplant International © 2011 European Society for Organ Transplantation.

  20. Ontario Hydro decontamination experience

    International Nuclear Information System (INIS)

    Lacy, C.S.; Patterson, R.W.; Upton, M.S.

    1991-01-01

    Ontario Hydro currently operates 18 nuclear electric generating units of the CANDU design with a net capacity of 12,402 MW(e). An additional 1,762 MW(e) is under construction. The operation of these facilities has underlined the need to have decontamination capability both to reduce radiation fields, as well as to control and reduce contamination during component maintenance. This paper presents Ontario Hydro decontamination experience in two key areas - full heat transport decontamination to reduce system radiation fields, and component decontamination to reduce loose contamination particularly as practised in maintenance and decontamination centres. (author)

  1. The OPERA experiment

    International Nuclear Information System (INIS)

    Gustavino, Carlo

    2006-01-01

    OPERA is a neutrino oscillation experiment designed to perform a ν τ appearance search in the future CNGS beam from CERN to Gran Sasso. The identification of the τ lepton produced by a CC ν τ interaction is based on the use of the nuclear emulsion technique. The OPERA detector is presently under construction in the Gran Sasso underground laboratory, 730 km from CERN, and will receive its first neutrinos in 2006. The experimental technique is reviewed and the development of the project described. Foreseen performances in measuring ν τ appearance and also in searching for ν e appearance are discussed

  2. Solar neutrino experiments

    Energy Technology Data Exchange (ETDEWEB)

    Hampel, W. [Max-Planck-Institut fuer Kernphysik, Heidelberg (Germany)

    1996-11-01

    The present status of experimental solar neutrino research is reviewed. Updated results from the Homestake, Kamiokande, GALLEX and SAGE detectors all show a deficit when compared to recent standard solar model calculations. Two of these detectors, GALLEX and SAGE, have recently been checked with artificial {sup 51}Cr neutrino sources. It is shown that astrophysical scenarios to solve the solar neutrino problems are not favoured by the data. There is hope that the results of forthcoming solar neutrino experiments can provide the answers to the open questions. (author) 6 figs., 3 tabs., 36 refs.

  3. The MUSE experiment

    Directory of Open Access Journals (Sweden)

    Downie E. J.

    2014-06-01

    Full Text Available The proton radius puzzle is the difference between the proton radius as measured with electron scattering and in the excitation spectrum of atomic hydrogen, and that measured with muonic hydrogen spectroscopy. The MUSE experiment seeks to resolve this puzzle by simultaneously measuring elastic electron and muon scattering on the proton, in both charge states, thereby providing new information to the puzzle. MUSE addresses issues of two-photon effects, lepton universality and, possibly, new physics, while providing simultaneous form factor, and therefore radius, measurements with both muons and electrons.

  4. Magnetic monopole search experiments

    International Nuclear Information System (INIS)

    Stone, J.L.

    1986-01-01

    Experimental searches for the elusive magnetic monopole have extended over 50 years -- ever since Dirac showed that the existence of isolated magnetic charges could account for the observation of quantized electric charge. Early searches for Dirac's monopole were hampered since there was no indication of the expected monopole mass, velocity, or origin in the theory. Consequently, numerous experiments searched more or less blindly for relativistic low mass monopoles in the cosmic rays and in particle collisions at high energy accelerators. In this paper, the author reviews briefly the monopole properties which are relevant for their detection and summarize current experimental efforts using induction, ionization/excitation, and catalysis techniques

  5. Copenhagen Sonic Experience Map

    DEFF Research Database (Denmark)

    Kreutzfeldt, Jacob

    2011-01-01

    of assessment and management of environmental noise brings forth the disturbing and potentially damaging effect of environmental sound.1 But as maps of coloured streets start to circulate, and real estate prices drop in designated blue and red areas,2 it is worth remembering that sound itself is not a killer....... Most of the time sound is a trivial part of everyday life involved in interactions, experiences, atmospheres, actions, etc. Although trivial, the role of the aural in the urban life world is more complex than what is suggested by sound level maps, and as such it may be a vital part of urbanity itself...

  6. The OTTI space experiments

    International Nuclear Information System (INIS)

    Brewer, D.A.; Clifton, K.S.; Pearson, S.D.; Barth, J.L.; LaBel, K.; Ritter, J.C.; Peden, J.; Campbell, A.; Liang, R.

    1999-01-01

    The orbiting technology tested initiative (OTTI) provides a concept for a series of space experiment platforms to be flown at 2-year interval over the next ten years. The long-term purpose of this program is to provide a convenient test-beds to simulate high radiation environments. The purposes of the first platform is to evaluate the on-orbit performance of novel, emerging, breakthrough technologies and advanced state-of-the-art devices in high radiation orbits and to provide correlations between the natural space radiation environment and the device response in the flight test-bed. This short article presents the concept of the OTTI program

  7. The QUIJOTE CMB Experiment

    Science.gov (United States)

    Rubiño-Martín, J. A.; Rebolo, R.; Tucci, M.; Génova-Santos, R.; Hildebrandt, S. R.; Hoyland, R.; Herreros, J. M.; Gómez-Reñasco, F.; Caraballo, C. López; Martínez-González, E.; Vielva, P.; Herranz, D.; Casas, F. J.; Artal, E.; Aja, B.; Fuente, L. dela; Cano, J. L.; Villa, E.; Mediavilla, A.; Pascual, J. P.; Piccirillo, L.; Maffei, B.; Pisano, G.; Watson, R. A.; Davis, R.; Davies, R.; Battye, R.; Saunders, R.; Grainge, K.; Scott, P.; Hobson, M.; Lasenby, A.; Murga, G.; Gómez, C.; Gómez, A.; Ariño, J.; Sanquirce, R.; Pan, J.; Vizcargüenaga, A.; Etxeita, B.

    We present the current status of the QUIJOTE (Q-U-I JOint TEnerife) CMB Experiment, a new instrument which will start operations early in 2009 at Teide Observatory with the aim of characterizing the polarization of the CMB and other processes of galactic and extragalactic emission in the frequency range 10-30GHz and at large angular scales. QUIJOTE will be a valuable complement at low frequencies for the PLANCK mission, and will have the required sensitivity to detect a primordial gravitational-wave component if the tensor-to-scalar ratio is larger than r = 0.05.

  8. The Experience City

    DEFF Research Database (Denmark)

    Marling, Gitte; Jensen, Ole B.; Kiib, Hans

    2012-01-01

    , for learning and for experience. The performative activity can take on the guise of events – something temporary, but still recurring, which influences the shape and identity of the space. The article contains four sections. In the first section we present three European cases outside Denmark in order...... findings. The projects are categorised according to their content, structure and urban localisation. In particular the cases are labelled in relation to their strategic and urban planning importance, their social and cultural content and their architectural representation and the programmes they contain...

  9. The Digital Archive Experience

    DEFF Research Database (Denmark)

    Søndergaard, Morten

    2009-01-01

    This article, as well as the book, investigates the ways in which new digital media may enhance the experience of the art-archive. Taken as a whole, the new media is a vital component of a 'transdisciplinary' and transformative field, a cultural landscape that is changing rapidly the conditions....... The book discusses the challenges of the archive and the (art)museum in the age of digital media. It is based upon documentation from a research project, MAP - Media Art Platform, that drew upon the talents and collaboration of many institutions, artists, programmers, art historians, designers and others...

  10. Experience of exclusion

    DEFF Research Database (Denmark)

    Pedersen, Maria; Overgaard, Dorthe; Andersen, Ingelise

    2017-01-01

    Background: The Danish public healthcare system provides comprehensive care based on the principle of equal access. However, it is well documented that patients with low socioeconomic position are less likely to participate in cardiac rehabilitation. More knowledge is needed to understand...... this phenomenon. The aim of the study was to explore the patient experience of barriers to completion of phase II cardiac rehabilitation, and to investigate the impact of socioeconomic factors on completion of cardiac rehabilitation. Methods: The study had a qualitative explorative design using semi...

  11. The Malaysia LNG experience

    International Nuclear Information System (INIS)

    Muhammed, M.

    1991-01-01

    This paper summarizes the nature of the LNG trade, the essential components and characteristics of an LNG project, and relates the Malaysia LNG experience to project realization with some emphasis on the financial aspects of the project. Twelve offshore lending institutions were involved in the total project loop providing U.S. dollar equivalents of 4.0 billions with interest rates ranging from 5% to 8%. The total project was completed on schedule and within budget except for the ships which got caught in the political development of the Malaysian petroleum industry at that time

  12. Magnetohydrodynamic Augmented Propulsion Experiment

    Science.gov (United States)

    Litchford, Ron J.; Cole, John; Lineberry, John; Chapman, Jim; Schmidt, Harold; Cook, Stephen (Technical Monitor)

    2002-01-01

    A fundamental obstacle to routine space access is the specific energy limitations associated with chemical fuels. In the case of vertical take-off, the high thrust needed for vertical liftoff and acceleration to orbit translates into power levels in the 10 GW range. Furthermore, useful payload mass fractions are possible only if the exhaust particle energy (i.e., exhaust velocity) is much greater than that available with traditional chemical propulsion. The electronic binding energy released by the best chemical reactions (e.g., LOX/LH2 for example, is less than 2 eV per product molecule (approx. 1.8 eV per H2O molecule), which translates into particle velocities less than 5 km/s. Useful payload fractions, however, will require exhaust velocities exceeding 15 km/s (i.e., particle energies greater than 20 eV). As an added challenge, the envisioned hypothetical RLV (reusable launch vehicle) should accomplish these amazing performance feats while providing relatively low acceleration levels to orbit (2-3g maximum). From such fundamental considerations, it is painfully obvious that planned and current RLV solutions based on chemical fuels alone represent only a temporary solution and can only result in minor gains, at best. What is truly needed is a revolutionary approach that will dramatically reduce the amount of fuel and size of the launch vehicle. This implies the need for new compact high-power energy sources as well as advanced accelerator technologies for increasing engine exhaust velocity. Electromagnetic acceleration techniques are of immense interest since they can be used to circumvent the thermal limits associated with conventional propulsion systems. This paper describes the Magnetohydrodynamic Augmented Propulsion Experiment (MAPX) being undertaken at NASA Marshall Space Flight Center (MSFC). In this experiment, a 1-MW arc heater is being used as a feeder for a 1-MW magnetohydrodynamic (MHD) accelerator. The purpose of the experiment is to demonstrate

  13. Demarcating User eXperience

    Science.gov (United States)

    Roto, Virpi

    This panel discusses the scoping of user experience as a research field. User experience is a crossing point of several disciplines, each of which tends to define user experience from their own perspective. The distinguished panelists from academia and industry represent the different perspectives to user experience: Traditional human-computer interaction, Psychology, Cognitive psychology, and Design. The goal of the panel is to get one step closer to a shared understanding of the concept of user experience.

  14. Jinping Neutrino Experiment

    Science.gov (United States)

    Wan, Linyan; Jinping Neutrino Experiment Research Group

    2017-09-01

    Jinping Neutrino Experiment (Jinping) is a unique observatory for low-energy neutrino physics, astrophysics and geophysics. Jinping is located in China JinPing underground Laboratory (CJPL), identified by the thickest overburden, lowest reactor neutrino background, etc. For solar neutrinos, Jinping has the capacity to measure the oscillation transition phase from vacuum to matter, to discover the CNO cycle neutrino, and to address the solar metallicity problem. Jinping will be able to precisely measure geo-neutrinos with signal-to-background ratio of 8.2:1.0 in the energy range of 1.8 MeV to 3.3 MeV. The ratio of U/Th can be determined to 10%. We also expect a promising sensitivity for neutrinos from a Milky Way supernova, the diffuse supernova neutrino background, and dark matter annihilation. The first, small phase of the laboratory (CJPL I) is already in operation, hosting dark matter experiments. The second, large phase (CJPL II) is already under construction, with ≈ 100,000 m3 being excavated.

  15. The EBEX Experiment

    International Nuclear Information System (INIS)

    Oxley, P.; Ade, P.; Baccigalupi, C.; deBernardis, P.; Cho, H-M.; Devlin, M.J.; Hanany, S.; Johnson, B.R.; Jones, T.; Lee, A.T.; Matsumura, T.; Miller, A.D.; Milligan, M.; Renbarger, T.; Spieler, H.G.; Stompor, R.; Tucker, G.S.; Zaldarriaga, M.

    2005-01-01

    EBEX is a balloon-borne polarimeter designed to measure the intensity and polarization of the cosmic microwave background radiation. The measurements would probe the inflationary epoch that took place shortly after the big bang and would significantly improve constraints on the values of several cosmological parameters. EBEX is unique in its broad frequency coverage and in its ability to provide critical information about the level of polarized Galactic foregrounds which will be necessary for all future CMB polarization experiments. EBEX consists of a 1.5 m Dragone-type telescope that provides a resolution of less than 8 arcminutes over four focal planes each of 4. diffraction limited field of view at frequencies up to 450 GHz. The experiment is designed to accommodate 330 transition edge bolometric detectors per focal plane, for a total of up to 1320 detectors. EBEX will operate with frequency bands centered at 150, 250, 350, and 450 GHz. Polarimetry is achieved with a rotating achromatic half-wave plate. EBEX is currently in the design and construction phase, and first light is scheduled for 2008

  16. Female physicist doctoral experiences

    Science.gov (United States)

    Dabney, Katherine P.; Tai, Robert H.

    2013-06-01

    The underrepresentation of women in physics doctorate programs and in tenured academic positions indicates a need to evaluate what may influence their career choice and persistence. This qualitative paper examines eleven females in physics doctoral programs and professional science positions in order to provide a more thorough understanding of why and how women make career choices based on aspects both inside and outside of school and their subsequent interaction. Results indicate that female physicists experience conflict in achieving balance within their graduate school experiences and personal lives and that this then influences their view of their future careers and possible career choices. Female physicists report both early and long-term support outside of school by family, and later departmental support, as being essential to their persistence within the field. A greater focus on informal and out-of-school science activities for females, especially those that involve family members, early in life may help influence their entrance into a physics career later in life. Departmental support, through advisers, mentors, peers, and women’s support groups, with a focus on work-life balance can help females to complete graduate school and persist into an academic career.

  17. Female physicist doctoral experiences

    Directory of Open Access Journals (Sweden)

    Katherine P. Dabney

    2013-04-01

    Full Text Available The underrepresentation of women in physics doctorate programs and in tenured academic positions indicates a need to evaluate what may influence their career choice and persistence. This qualitative paper examines eleven females in physics doctoral programs and professional science positions in order to provide a more thorough understanding of why and how women make career choices based on aspects both inside and outside of school and their subsequent interaction. Results indicate that female physicists experience conflict in achieving balance within their graduate school experiences and personal lives and that this then influences their view of their future careers and possible career choices. Female physicists report both early and long-term support outside of school by family, and later departmental support, as being essential to their persistence within the field. A greater focus on informal and out-of-school science activities for females, especially those that involve family members, early in life may help influence their entrance into a physics career later in life. Departmental support, through advisers, mentors, peers, and women’s support groups, with a focus on work-life balance can help females to complete graduate school and persist into an academic career.

  18. The Halogen Occultation Experiment

    Science.gov (United States)

    Russell, James M., III; Gordley, Larry L.; Park, Jae H.; Drayson, S. R.; Hesketh, W. D.; Cicerone, Ralph J.; Tuck, Adrian F.; Frederick, John E.; Harries, John E.; Crutzen, Paul J.

    1993-01-01

    The Halogen Occultation Experiment (HALOE) uses solar occultation to measure vertical profiles of O3, HCl, HF, CH4, H2O, NO, NO2, aerosol extinction, and temperature versus pressure with an instantaneous vertical field of view of 1.6 km at the earth limb. Latitudinal coverage is from 80 deg S to 80 deg N over the course of 1 year and includes extensive observations of the Antarctic region during spring. The altitude range of the measurements extends from about 15 km to about 60-130 km, depending on channel. Experiment operations have been essentially flawless, and all performance criteria either meet or exceed specifications. Internal data consistency checks, comparisons with correlative measurements, and qualitative comparisons with 1985 atmospheric trace molecule spectroscopy (ATMOS) results are in good agreement. Examples of pressure versus latitude cross sections and a global orthographic projection for the September 21 to October 15, 1992, period show the utility of CH4, HF, and H2O as tracers, the occurrence of dehydration in the Antarctic lower stratosphere, the presence of the water vapor hygropause in the tropics, evidence of Antarctic air in the tropics, the influence of Hadley tropical upwelling, and the first global distribution of HCl, HF, and NO throughout the stratosphere. Nitric oxide measurements extend through the lower thermosphere.

  19. PAC Experiments at ISOLDE

    CERN Multimedia

    2002-01-01

    The study of hyperfine interactions offers the possibility to use radioactive nuclei as probes in matter. The @g-@g perturbated angular correlation (PAC) technique following implantation has found widespread application in this field. At ISOLDE we have been investigating electric field gradients at impurities in non-cubic metals in an ongoing series of experiments. \\\\ \\\\ The small number of probe atoms necessary for these measurements make them also ideally suited for studies of surface problems like diffusion, structure and dynamics. Cd on a molybdenum O110? surface will be studied as first system. For this purpose 10|1|0~atoms of |1|1|1|mCd will be evaporated onto the clean surface and the electric field gradient for isolated adatoms on terrace sites will be determined by PAC. The UHV system constructed for such experiments at ISOLDE is shown in the schematic drawing. It is coupled to the beam line through differential pumping stations and contains standard surface treatment and analysis equipment.

  20. Postmenopausal osteoporosis: Our experience

    Directory of Open Access Journals (Sweden)

    R N Mehrotra

    2012-01-01

    Full Text Available Introduction: There is very little published literature about experience with osteoporosis treatment from our country. Materials and Methods: It is a retrospective analysis of first 50 patients enrolled in our clinic for osteoporosis. Postmenopausal women with T score of less than -2.5 or history suggestive fragility fracture with supportive bone mineral density (BMD were included. Patients having hypercalcemia, abnormal renal function, myeloma and on long-term steroids were also excluded. Results: Nearly 34% subjects were below the age of 60 years, 47% of subjects were between 60 and 70 years, whereas 18% were above 70 years. Nearly 6% had family history of osteoporosis s or history of osteoporotic fractures. Nearly 20% subjects had fracture prior to starting of any treatment. A total of 86% (40/46 had evidence of Vitamin D (VD deficiency. Nearly 80% of patients were treated with bisphosphonates, 12% were treated with injectable bisphosphonates, and 8% were treated with teriperatide. Nearly 16% patients had duration of more than 5 years of experience with bisphosphonates. Follow up BMD was available in 25 subjects. BMD had improved significantly in 68% of subjects. In 24% the BMD was stable (the change was less than least significant change (LSC. In 8% BMD had shown a significant decline while being on treatment. Conclusion: Postmenopausal osteoporosis occurs in relatively younger women in our country. Majority of them are VD deficient. Oral bisphosphonates is the most common used drug; it is fairly well tolerated and effective.