Removal of alpha-pinene from gases using biofilters containing fungi

Science.gov (United States)

van Groenestijn, J. W.; Liu, J. X.

Biofiltration is cost-effective for the treatment of gases containing low concentrations of volatile organic compounds (elimination of hydrophobic compounds. Besides that, biofilter operational stability is often hampered by acidification and drying out of the filter bed. To overcome these problems, biofilters with fungi on inert packing material have been developed. Fungi are more resistant to acid and dry conditions than bacteria, and it is hypothesised that the aerial mycelia of fungi, which are in direct contact with the gas, can take up hydrophobic compounds faster than flat aqueous bacterial biofilm surfaces. Alpha-pinene was chosen as a model compound. It is an odorous compound emitted by the wood processing industry. In 2 l biofilter columns four different packing materials were tested: perlite, expanded clay granules, polyurethane foam cubes and compost. The filters were inoculated with forest soil and ventilated with gas containing alpha-pinene. Start up took 1-2 months and removal efficiencies of more than 90% were observed, but mostly ranged from 50% to 90% due to overloading. In the filters containing perlite, clay, polyurethane and compost volumetric removal capacities of, respectively, 24, 33, 38 and 24 g alpha- pinene m -3 filter bed h -1 were attained and the gas pressure drops in the 60 cm high filter beds measured at a superficial gas velocity of 35 m h -1 were 70, 550, 180 and 250 Pa. The results indicate that it is possible to develop biofilters based on the action of fungi with higher elimination capacities for alpha-pinene as reported in literature for bacterial biofilters. The use of polyurethane foam cubes is preferred because of the low gas pressure drop in combination with a high volumetric elimination capacity.

Dynamic model development and validation for a nitrifying moving bed biofilter: Effect of temperature and influent load on the performance

DEFF Research Database (Denmark)

Sin, Gürkan; Weijma, Jan; Spanjers, Henri

2008-01-01

A mathematical model with adequate complexity integrating hydraulics, biofilm and microbial conversion processes is successfully developed for a continuously moving bed biofilter performing tertiary nitrification. The model was calibrated and validated using data from Nether Stowey pilot plant...... on the ammonium removal efficiency, doubling nitrification capacity every 5 degrees C increase. However, at temperatures higher than 20 degrees C, the biofilm thickness starts to decrease due to increased decay rate. The influent nitrogen load was also found to be influential on the filter performance, while...... the hydraulic loading had relatively negligible impact. Overall, the calibrated model can now reliably be used for design and process optimization purposes....

Effects of periods of nonuse and fluctuating ammonia concentration on biofilter performance.

Science.gov (United States)

Chen, Ying-Xu; Yin, Jun; Wang, Kai-Xiong; Fang, Shi

2004-01-01

A systematic study on the transient behavior of odor treatment using biofilters is described. The biofilters were exposed to variations in contaminant loading and periods of nonuse. Two bench-scale biofilters with different filter media were used. Mixtures of compost/perlite (5:1) and dry sludge/granular active carbon (5:1) were used as filter media. Ammonia (NH3), one of the main malodorous gases, was used as the target compound. The response of each biofilter to variations in contaminant mass loading, periodic nonuse, water content, and inlet concentration pulse was studied. The nonuse period comprised of two stages: the "idle phase" when no air was passing through the biofilters, and the "no-contaminant-loading phase" when only humidified air was passing through the biofilters. Concentration spike was applied to study the effects of shock loading on the biofilter performance. Biofilters responded effectively to NH3 concentration variations and shock loading by rapidly recovering to the original removal rates within 6-12h. The results indicated re-acclimation times ranged from several hours to longer than a day. Longer idle phase produced longer re-acclimation periods than periods of no contaminant loading. When the media was dried during the biofiltration process, elimination capacity dropped accordingly for both biofilters. After 24 h of drying, the biofilter experiment could be restarted and run for a few days for recovering.

Aerated biofilters with multiple-level air injection configurations to enhance biological treatment of methane emissions.

Science.gov (United States)

Farrokhzadeh, Hasti; Hettiaratchi, J Patrick A; Jayasinghe, Poornima; Kumar, Sunil

2017-09-01

Aiming to improve conventional methane biofilter performance, a multiple-level aeration biofilter design is proposed. Laboratory flow-through column experiments were conducted to evaluate three actively-aerated methane biofilter configurations. Columns were aerated at one, two, and three levels of the bed depth, with air introduced at flow rates calculated from methane oxidation reaction stoichiometry. Inlet methane loading rates were increased in five stages between 6 and 18mL/min. The effects of methane feeding rate, levels of aeration, and residence time on methane oxidation rates were determined. Samples collected after completion of flow-through experiments were used to determine methane oxidation kinetic parameters, V max , K m , and methanotrophic community distribution across biofilter columns. Results obtained from mixed variances analysis and response surfaces, as well as methanotrophic activity data, suggested that, biofilter column with two aeration levels has the most even performance over time, maintaining 85.1% average oxidation efficiency over 95days of experiments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Degradation and effect of hydrogen peroxide in small-scale recirculation aquaculture system biofilters

DEFF Research Database (Denmark)

Møller, Martin Sune; Arvin, Erik; Pedersen, Lars-Flemming

2010-01-01

From an environmental point of view, hydrogen peroxide (HP) has beneficial attributes compared with other disinfectants in terms of its ready degradation and neutral by-products. The rapid degradation of HP can, however, cause difficulties with regard to safe and efficient water treatment when...... applied in different systems. In this study, we investigated the degradation kinetics of HP in biofilters from water recirculating aquaculture systems (RAS). The potential effect of HP on the nitrification process in the biofilters was also examined. Biofilter elements from two different pilot-scale RAS......−1 maintained over 3 h had a moderate inhibitory effect on the biofilter elements from one of the RAS with relatively high organic loading, while the nitrification was severely inhibited in the pilot-scale biofilters from the other RAS with a relatively low organic loading. A pilot-scale RAS...

Microbial Community in a Biofilter for Removal of Low Load Nitrobenzene Waste Gas.

Directory of Open Access Journals (Sweden)

Jian Zhai

Full Text Available To improve biofilter performance, the microbial community of a biofilter must be clearly defined. In this study, the performance of a lab-scale polyurethane biofilter for treating waste gas with low loads of nitrobenzene (NB (< 20 g m-3 h-1 was investigated when using different empty bed residence times (EBRT (64, 55.4 and 34 s, respectively. In addition, the variations of the bacterial community in the biofilm on the longitudinal distribution of the biofilters were analysed by using Illumina MiSeq high-throughput sequencing. The results showed that NB waste gas was successfully degraded in the biofilter. High-throughput sequencing data suggested that the phylum Actinobacteria and genus Rhodococcus played important roles in the degradation of NB. The variations of the microbial community were attributed to the different intermediate degradation products of NB in each layer. The strains identified in this study were potential candidates for purifying waste gas effluents containing NB.

Ethylbenzene removal under mesophilic conditions in a multiple-stage biofilter with macadamia nutshells as carrier material

OpenAIRE

Volckaert, Diego; Alvarez Hornos, Francisco Javier; Heynderickx, Philippe; Van Langenhove, Herman

2011-01-01

A biofilter was used to treat air polluted with ethylbenzene. Macadamia nutshells, which are a cheap waste product in Thailand, were chosen as the packing material for the biofilter. The moisture content (6.6 w%), water holding capacity (16.8 w%), nutshell density (1.3 g ml-1) and organic content (78.0 w%) of the macadamia nutshell were measured. The biofilter was operated during 5 months, in which several inlet loads (IL), empty bed residence times (EBRT) and temperatures (T) were applied. A...

Biofiltration of Chloroform in a Trickle Bed Air Biofilter Under ...

Science.gov (United States)

In this paper, the application of biofiltration is investigated for controlled removal of gas phase chloroform through cometabolic degradation with ethanol. A trickle bed air biofilter (TBAB) operated under acidic pH 4 is subjected to aerobic biodegradation of chloroform and ethanol. The TBAB is composed of pelleted diatomaceous earth filter media inoculated with filamentous fungi species, which served as the principle biodegrading microorganism. The removal efficiencies of 5 ppmv of chloroform mixed with different ratios of ethanol as cometabolite (25, 50, 100, 150, and 200 ppmv) ranged between 69.9 and 80.9%. The removal efficiency, reaction rate kinetics, and the elimination capacity increased proportionately with an increase in the cometabolite concentration. The carbon recovery from the TBAB amounted to 69.6% of the total carbon input. It is postulated that the remaining carbon contributed to excess biomass yield within the system. Biomass control strategies such as starvation and stagnation were employed at different phases of the experiment. The chloroform removal kinetics provided a maximum reaction rate constant of 0.0018 s−1. The highest ratio of chemical oxygen demand (COD)removal/nitrogenutilization was observed at 14.5. This study provides significant evidence that the biodegradation of a highly chlorinated methane can be favored by cometabolism in a fungi-based TBAB. Chloroform is volatile hazardous chemical emitted from publicly owned treatment

Treatment of Benzene and n-Hexane Mixtures in Trickle-Bed Air Biofilters.

Science.gov (United States)

Hassan, Ashraf Aly; Sorial, George A

2011-02-01

Trickle-bed air biofilters (TBABs) are suitable for treatment of hydrophilic volatile organic compounds, but they pose a challenge for hydrophobic compounds. Three laboratory-scale TBABs were used for the treatment of an airstream contaminated with different ratios of n-hexane and benzene mixtures. The ratios studied were 1:1, 2:1, and 1:3 n-hexane:benzene by volume. Each TBAB was operated at a pH of 4 and a temperature of 20 °C. The use of acidic-buffered nutrient solution was targeted for changing the microorganism consortium to fungi as the main biodegradation element. The experimental plan was designed to investigate the long-term performance of the TBABs with an emphasis on different mixture loading rates, removal efficiency with TBAB depth, volatile suspended solids, and carbon mass balance closure. n-Hexane loading rate was kept constant in the TBABs for comparison reasons and ranged from 4 to 22 g/(m 3 .hr). Corresponding benzene loadings ranged from 4 to 43 g/(m 3 .hr). Generally, benzene behavior in the TBAB was superior to that of n-hexane because of its higher solubility. n-Hexane showed improved performance in the 2:1 mixing ratio as compared with the other two ratios. [Box: see text].

Treatment of waste gas containing low concentration of dimethyl sulphide (DMS) in a bench-scale biofilter.

Science.gov (United States)

Giri, B S; Mudliar, S N; Deshmukh, S C; Banerjee, S; Pandey, R A

2010-04-01

Biological treatment of dimethyl sulphide (DMS) was investigated in a bench-scale biofilter, packed with compost along with wood chips, and enriched with DMS degrading microorganism Bacillus sphaericus. The biofilter could remove 62-74% of the inlet DMS, at an optimum loading of 0.484 g/m(3)/h with optimum empty bed contact time (EBCT) of 384 s and an average moisture range of 65-70%. The biodegradative products of DMS were sulphide, thiosulphate and sulphate. Evaluation of microbiological status of the biofilter indicated the presence of other bacterial cultures viz. Paenibacillus polymyxa, and Bacillus megaterium, besides B. sphaericus. Copyright 2009 Elsevier Ltd. All rights reserved.

A simple biofilter for treatment of pig slurry in Malaysia.

Science.gov (United States)

Sommer, S G; Mathanpaal, G; Dass, G T

2005-03-01

On commercial pig production farms in South East (SE) Asia, the liquid effluent is often discharged into rivers. The discharge is a hazard to the environment and to the health of people using water from the river either for consumption or for irrigation. Therefore, a simple percolation biofilter for treatment of the liquid effluent was developed. Pig slurry was treated in test-biofilters packed with different biomass for the purpose of selecting the most efficient material, thereafter the efficiency of the biofilter was examined at farm scale with demo biofilters using the most efficient material. The effect of using "Effective Microorganisms" (EM) added to slurry that was treated with biofilter material mixed with Glenor KR+ was examined. Slurry treatment in the test-biofilters indicated that rice straw was better than coconut husks, wood shavings, rattan strips and oil palm fronds in reducing BOD. Addition of EM and Glenor KR+ to slurry and biofilter material, respectively, had no effect on the temperature of the biofilter material or on the concentrations of organic and inorganic components of the treated slurry. The BOD of slurry treated in test biofilters is reduced to between 80 and 637 mg O2 I(-1) and in the demo biofilter to between 3094 and 3376 mg O2 l(-1). The concentration of BOD in the effluent is related to the BOD in the slurry being treated and the BOD concentration in slurry treated in test biofilters was lower than BOD of slurry treated in demo biofilters. The demo biofilter can reduce BOD to between 52 an 56% of the original value, and TSS, COD (chemical oxygen demand) and ammonium (NH4+) to 41-55% of the original slurry. The treated effluent could not meet the standards for discharge to rivers. The composted biofilter material has a high content of nitrogen and phosphorus; consequently, the fertilizer value of the compost is high. The investments costs were 123 US dollar per SPP which has to be reduced if this method should be a treatment option

Biological treatment of aqueous effluents in a bacterial bed

Energy Technology Data Exchange (ETDEWEB)

1978-12-14

Biological treatment of aqueous effluents in a bacterial bed is carried out effectively for refinery waters having a low five-day BOD by using a plastic packing to support the bacteria in place of the less reliable pozzolana (volcanic ash) formerly employed. Such biofilters, developed by Lurgi S.A., are more sensitive to BOD overloading than activated sludge beds, so that very stable operating conditions are required. In these bacterial beds, the water trickles over the plastic packing and becomes oxygenated, which leads to degradation of undesirable substances in the water. In the refinery, this process can give excellent results when properly carried out, but the biofilter may generate suspended matter under unsatisfactory operating conditions, and is therefore usually placed upstream from the flocculation and filtration units. To date, all installations have remained below the required standard limit of 30 mg/l. of suspended matter.

Influence of fixed and moving bed biofilters on micro particle dynamics in a recirculating aquaculture system

DEFF Research Database (Denmark)

Fernandes, Paulo; Pedersen, Lars-Flemming; Pedersen, Per Bovbjerg

2017-01-01

(Oncorhynchus mykiss), and operatedunder constant feed loading conditions (1 kg feed/m3of make-up water) for more than three months.Production or removal of micro particles according to biofilter mode of operation (FBB vs. MBB) wasassessed by operating all biofilters simultaneously as well as separately...... particle concentration also represented a 10% reduction in total particle surface area and particlevolume. In MBB, a 10% increase in particle concentration also represented a 10% increase in total particlesurface area, but had no effect on total particle volume. A volumetric reduction of particles >100 m...... due to disintegration of particles inMBB. In the RAS, ammonia and nitrite were observed at concentrations below 0.20 mg N/L throughoutthe majority of the experiment. However, during the phase where only MBB were in operation, TAN(Total Ammonia Nitrogen) and nitrite levels increased significantly...

Biofiltration of methanol in an organic biofilter using peanut shells as medium.

Science.gov (United States)

Ramirez-Lopez, E M; Corona-Hernandez, J; Avelar-Gonzalez, F J; Omil, F; Thalasso, F

2010-01-01

Biofiltration consists of a filter-bed of organic matter serving both as carrier for the active biomass and as nutrient supply, through which the polluted gas passes. The selection of a suitable medium material is of major importance to ensure optimum biofilter efficiency. Peanut shells are an agricultural byproduct locally available in large quantities at a low price in most tropical and sub-tropical countries. A previous study showed that peanut shells are physically and chemically suitable for biofiltration. This paper presents the results obtained during a six month biofiltration experiment using peanut shells as medium and methanol as air pollutant. It is shown that peanut shells are potentially suitable as biofiltration medium, since degradation rates of up to 30 kg MeOH/m(3)d with an empty bed residence time of 19s was obtained. The biofilter showed a good resistance to shock load and no operational problems were observed.

Use of biofilters and suspended-growth reactors to treat VOC's

Energy Technology Data Exchange (ETDEWEB)

Neal, A.B.; Loehr, R.C.

2000-07-01

The greater limits placed on volatile organic compound (VOC) emissions by the Clean Air Act Amendments have stimulated evaluation of various VOC treatment methods. Two applicable gas phase treatment technologies are biofiltration and suspended growth reactors. Biofiltration removes contaminants from gas streams that are passed through a bed of biologically active solids. An aerobic suspended-growth reactor (SGR) removes VOCs by biologically treating contaminated air bubbled through an aqueous suspension of active microorganisms. This research compared the performance of a typical compost biofilter to a SGR for the removal of a common VOC (toluene) from gas streams. The objective was to evaluate the impact of mass loading on process performance. Major performance parameters investigated were (1) mass emitted and elimination capacity, (2) off-gas concentrations exiting each type of reactor for various mass loadings, and (3) removal efficiencies obtained by each type of reactor. The results indicated that SGRs can effectively treat gases containing VOCs. For mass loadings ranging from 5 to 30 mg/l-h, the biofilters and SGRs achieved similar VOC removals, in the range of 96--99.7%. Drying of the biofilter medium occurred a high mass loadings. In the SGRs, at mass loadings greater than 17 mg/l-h, process performance decreased when an unknown colored substance was present.

A High Performance Biofilter for VOC Emission Control.

Science.gov (United States)

Wu, G; Conti, B; Leroux, A; Brzezinski, R; Viel, G; Heitz, M

1999-02-01

Biofiltration is a cleaning technique for waste air contaminated with some organic compounds. The advantages of the conventional biofilter over other biological systems are a high-superficial area best suited for the treatment of some compounds with poor water solubility, ease of operation, and low operating costs. It has crucial disadvantages, however; for example, it is not suitable to treat waste gases with high VOC concentrations and it has poor control of reaction conditions. To improve on these problems and to build a high-performance biofilter, three structured peat media and two trickling systems have been introduced in this study. The influences of media size and composition have been investigated experimentally. Peat bead blended with 30% (w/w) certain mineral material with a good binding capacity has advantages over other packing materials, for example, suitable size to prevent blockage due to microbial growth, strong buffering capacity to neutralize acidic substances in the system, and a pH range of 7.0-7.2 suitable for the growth of bacteria. Dropwise trickling system offers an effective measure to easily control the moisture content of the bed and the reaction conditions (pH, nutrient) and to partially remove excess biomass produced during the metabolic processes of microorganisms. The influence of nutrient supplementation has also been investigated in this study, which has revealed that the biological system was in a condition of nutrient limitation instead of carbon limitation. The biofilters built in our laboratory were used to treat waste gas contaminated with toluene in a concentration range of 1 to 3.2 g/m 3 and at the specific gas flow rate of 24 to120 m 3 /m 2 .hr. Under the conditions employed, a high elimination capacity (135 g/m 3 .hr) was obtained in the biofilter packed with peat beads (blended with 30% of the mineral material), and no blockage problem was observed in an experimental period of 2-3 months.

Temporal and Spatial Stability of Ammonia-Oxidizing Archaea and Bacteria in Aquarium Biofilters

KAUST Repository

Bagchi, Samik; Vlaeminck, Siegfried E.; Sauder, Laura A.; Mosquera, Mariela; Neufeld, Josh D.; Boon, Nico; Poulain, Alexandre

2014-01-01

Nitrifying biofilters are used in aquaria and aquaculture systems to prevent accumulation of ammonia by promoting rapid conversion to nitrate via nitrite. Ammonia-oxidizing archaea (AOA), as opposed to ammonia-oxidizing bacteria (AOB), were recently identified as the dominant ammonia oxidizers in most freshwater aquaria. This study investigated biofilms from fixed-bed aquarium biofilters to assess the temporal and spatial dynamics of AOA and AOB abundance and diversity. Over a period of four months, ammonia-oxidizing microorganisms from six freshwater and one marine aquarium were investigated at 4–5 time points. Nitrogen balances for three freshwater aquaria showed that active nitrification by aquarium biofilters accounted for ≥81–86% of total nitrogen conversion in the aquaria. Quantitative PCR (qPCR) for bacterial and thaumarchaeal ammonia monooxygenase (amoA) genes demonstrated that AOA were numerically dominant over AOB in all six freshwater aquaria tested, and contributed all detectable amoA genes in three aquarium biofilters. In the marine aquarium, however, AOB outnumbered AOA by three to five orders of magnitude based on amoA gene abundances. A comparison of AOA abundance in three carrier materials (fine sponge, rough sponge and sintered glass or ceramic rings) of two three-media freshwater biofilters revealed preferential growth of AOA on fine sponge. Denaturing gel gradient electrophoresis (DGGE) of thaumarchaeal 16S rRNA genes indicated that community composition within a given biofilter was stable across media types. In addition, DGGE of all aquarium biofilters revealed low AOA diversity, with few bands, which were stable over time. Nonmetric multidimensional scaling (NMDS) based on denaturing gradient gel electrophoresis (DGGE) fingerprints of thaumarchaeal 16S rRNA genes placed freshwater and marine aquaria communities in separate clusters. These results indicate that AOA are the dominant ammonia-oxidizing microorganisms in freshwater aquarium

Temporal and Spatial Stability of Ammonia-Oxidizing Archaea and Bacteria in Aquarium Biofilters

KAUST Repository

Bagchi, Samik

2014-12-05

Nitrifying biofilters are used in aquaria and aquaculture systems to prevent accumulation of ammonia by promoting rapid conversion to nitrate via nitrite. Ammonia-oxidizing archaea (AOA), as opposed to ammonia-oxidizing bacteria (AOB), were recently identified as the dominant ammonia oxidizers in most freshwater aquaria. This study investigated biofilms from fixed-bed aquarium biofilters to assess the temporal and spatial dynamics of AOA and AOB abundance and diversity. Over a period of four months, ammonia-oxidizing microorganisms from six freshwater and one marine aquarium were investigated at 4–5 time points. Nitrogen balances for three freshwater aquaria showed that active nitrification by aquarium biofilters accounted for ≥81–86% of total nitrogen conversion in the aquaria. Quantitative PCR (qPCR) for bacterial and thaumarchaeal ammonia monooxygenase (amoA) genes demonstrated that AOA were numerically dominant over AOB in all six freshwater aquaria tested, and contributed all detectable amoA genes in three aquarium biofilters. In the marine aquarium, however, AOB outnumbered AOA by three to five orders of magnitude based on amoA gene abundances. A comparison of AOA abundance in three carrier materials (fine sponge, rough sponge and sintered glass or ceramic rings) of two three-media freshwater biofilters revealed preferential growth of AOA on fine sponge. Denaturing gel gradient electrophoresis (DGGE) of thaumarchaeal 16S rRNA genes indicated that community composition within a given biofilter was stable across media types. In addition, DGGE of all aquarium biofilters revealed low AOA diversity, with few bands, which were stable over time. Nonmetric multidimensional scaling (NMDS) based on denaturing gradient gel electrophoresis (DGGE) fingerprints of thaumarchaeal 16S rRNA genes placed freshwater and marine aquaria communities in separate clusters. These results indicate that AOA are the dominant ammonia-oxidizing microorganisms in freshwater aquarium

Influence of fixed and moving bed biofilters on micro particle dynamics in a recirculating aquaculture system

DEFF Research Database (Denmark)

Fernandes, Paulo; Pedersen, Lars-Flemming; Pedersen, Per Bovbjerg

2017-01-01

(Oncorhynchus mykiss), and operatedunder constant feed loading conditions (1 kg feed/m3of make-up water) for more than three months.Production or removal of micro particles according to biofilter mode of operation (FBB vs. MBB) wasassessed by operating all biofilters simultaneously as well as separately...... due to disintegration of particles inMBB. In the RAS, ammonia and nitrite were observed at concentrations below 0.20 mg N/L throughoutthe majority of the experiment. However, during the phase where only MBB were in operation, TAN(Total Ammonia Nitrogen) and nitrite levels increased significantly...

Hydrodynamic behaviour and comparison of technologies for the removal of excess biomass in gas-phase biofilters.

Science.gov (United States)

Mendoza, J A; Prado, O J; Veiga, M C; Kennes, C

2004-01-01

The hydrodynamic behaviour of a biofilter fed toluene and packed with an inert carrier was evaluated on start-up and after long-term operation, using both methane and styrene as tracers in Residence Time Distribution experiments. Results indicated some deviation from ideal plug flow behaviour after 2-year operation. It was also observed that the retention time of VOCs gradually increased with time and was significantly longer than the average residence time of the bulk gas phase. Non-ideal hydrodynamic behaviour in packed beds may be due to excess biomass accumulation and affects both reactor modeling and performance. Therefore, several methods were studied for the removal of biomass after long-term biofilter operation: filling with water and draining, backwashing, and air sparging. Several flow rates and temperatures (20-60 degrees C) were applied using either water or different chemicals (NaOH, NaOCl, HTAB) in aqueous solution. Usually, higher flow rates and higher temperatures allowed the removal of more biomass, but the efficiency of biomass removal was highly dependent on the pressure drop reached before the treatment. The filling/draining method was the least efficient for biomass removal, although the treatment did basically not generate any biological inhibition. The efficiency of backwashing and air sparging was relatively similar and was more effective when adding chemicals. However, treatments with chemicals resulted in a significant decrease of the biofilter's performance immediately after applying the treatment, needing periods of several days to recover the original performance. The effect of manually mixing the packing material was also evaluated in duplicate experiments. Quite large amounts of biomass were removed but disruption of the filter bed was observed. Batch assays were performed simultaneously in order to support and quantify the observed inhibitory effects of the different chemicals and temperatures used during the treatments.

Fate of water borne therapeutic agents and associated effects on nitrifying biofilters in recirculating aquaculture systems

DEFF Research Database (Denmark)

Pedersen, Lars-Flemming

of these agents on biofilter nitrification performance. All experiments were conducted through addition of chemical additives to closed pilot scale recirculating aquaculture systems (RAS) with fixed media submerged biofilters under controlled operating conditions with rainbow trout (Oncorhynchus mykiss...... to positively correlate to temperature, available biofilter surface-area, and the frequency of FA-exposure. Prolonged biofilter exposure to FA did not negatively affect nitrification, and could therefore be a method to optimize FA treatment in RAS and reduce FA discharge. HP degradation was rapid and could...... prolonged multiple HP dosages at 10 mg/L were found to inhibit nitrite oxidation in systems with low organic loading. PAA decay was found to be concentration-dependent. It had a considerable negative effect on nitrite oxidation over a prolonged period of time when applied at a dosage ≥2 mg/L. PAA and HP...

Evaluating the impact of water supply strategies on p-xylene biodegradation performance in an organic media-based biofilter.

Science.gov (United States)

Gallastegui, G; Muñoz, R; Barona, A; Ibarra-Berastegi, G; Rojo, N; Elías, A

2011-01-30

The influence of water irrigation on both the long-term and short-term performance of p-xylene biodegradation under several organic loading scenarios was investigated using an organic packing material composed of pelletised sawdust and pig manure. Process operation in a modular biofilter, using no external water supply other than the moisture from the saturated inlet air stream, showed poor p-xylene abatement efficiencies (≈33 ± 7%), while sustained irrigation every 25 days rendered a high removal efficiency (RE) for a critical loading rate of 120 g m(-3)h(-1). Periodic profiles of removal efficiency, temperature and moisture content were recorded throughout the biofilter column subsequent to each biofilter irrigation. Hence, higher p-xylene biodegradation rates were always initially recorded in the upper module, which resulted in a subsequent increase in temperature and a decrease in moisture content. This decrease in the moisture content in the upper module resulted in a higher removal rate in the middle module, while the moisture level in the lower module steadily increased as a result of water condensation. Based on these results, mass balance calculations performed using measured bed temperatures and relatively humidity values were successfully used to account for water balances in the biofilter over time. Finally, the absence of bed compaction after 550 days of continuous operation confirmed the suitability of this organic material for biofiltration processes. Copyright © 2010 Elsevier B.V. All rights reserved.

Treatment of waste gas from the breather vent of a vertical fixed roof p-xylene storage tank by a trickle-bed air biofilter.

Science.gov (United States)

Chang, Shenteng; Lu, Chungsying; Hsu, Shihchieh; Lai, How-Tsan; Shang, Wen-Lin; Chuang, Yeong-Song; Cho, Chi-Huang; Chen, Sheng-Han

2011-01-01

This study applied a pilot-scale trickle-bed air biofilter (TBAB) system for treating waste gas emitted from the breather vent of a vertical fixed roof storage tank containing p-xylene (p-X) liquid. The volatile organic compound (VOC) concentration of the waste gas was related to ambient temperature as well as solar radiation, peaking at above 6300 ppmv of p-X and 25000 ppmv of total hydrocarbons during the hours of 8 AM to 3 PM. When the activated carbon adsorber was employed as a VOC buffer, the peak waste gas VOC concentration was significantly reduced resulting in a stably and efficiently performing TBAB system. The pressure drop appeared to be low, reflecting that the TBAB system could be employed in the prolonged operation with a low running penalty. These advantages suggest that the TBAB system is a cost-effective treatment technology for VOC emission from a fixed roof storage tank. Copyright © 2010 Elsevier Ltd. All rights reserved.

Nitrogen Transformation and Microbial Spatial Distribution in Drinking Water Biofilter

Science.gov (United States)

Qian, Yongxing; Zhang, Huining; Jin, Huizheng; Wu, Chengxia

2018-02-01

Well understanding the rule of nitrogen mutual transformation in biofilters is important for controlling the DBPs formation in the subsequent disinfection process. Ammonia nitrogen removal effect and nitrogen transformation approach in biofilter of drinking water was researched in the study. The biofilter removed ammonia of 48.5% and total phosphorus of 72.3%. And the removal rate of TN, NO3 --N, DON were 37.1%, 33.1%, 46.9%, respectively. Biomass and bioactivity of different depth of the biofilter were determined, too. The overall distribution of biomass showed a decreasing trend from top to bottom. The bioactivity in lower layer gradually increased. Especially the bioactivity of heterotrophic microorganisms showed a gradual increase trend. The amount of the nitrogen loss was 3.06mg/L. Non-nitrification pathway of “nitrogen loss” phenomenon in biofilter might exist assimilation, nitrification and denitrification in autotrophic.

Liquid Film Diffusion on Reaction Rate in Submerged Biofilters

DEFF Research Database (Denmark)

Christiansen, Pia; Hollesen, Line; Harremoës, Poul

1995-01-01

Experiments were carried out in order to investigate the influence of liquid film diffusion on reaction rate in a submerged biofilter with denitrification and in order to compare with a theoretical study of the mass transfer coefficient. The experiments were carried out with varied flow, identified...... by the empty bed velocity of inflow and recirculation, respectively 1.3, 2.8, 5.6 and 10.9 m/h. The filter material consisted of 3 mm biostyren spheres. The results indicate that the influence of liquid film diffusion on reaction rate can be ignored....

Relevance and diversity of Nitrospira populations in biofilters of brackish RAS.

Directory of Open Access Journals (Sweden)

Myriam Kruse

Full Text Available Lithoautotrophic nitrite-oxidizing bacterial populations from moving-bed biofilters of brackish recirculation aquaculture systems (RAS; shrimp and barramundi were tested for their metabolic activity and phylogenetic diversity. Samples from the biofilters were labeled with (13C-bicarbonate and supplemented with nitrite at concentrations of 0.3, 3 and 10 mM, and incubated at 17 and 28°C, respectively. The biofilm material was analyzed by fatty acid methyl ester - stable isotope probing (FAME-SIP. High portions of up to 45% of Nitrospira-related labeled lipid markers were found confirming that Nitrospira is the major autotrophic nitrite oxidizer in these brackish systems with high nitrogen loads. Other nitrite-oxidizing bacteria such as Nitrobacter or Nitrotoga were functionally not relevant in the investigated biofilters. Nitrospira-related 16S rRNA gene sequences were obtained from the samples with 10 mM nitrite and analyzed by a cloning approach. Sequence studies revealed four different phylogenetic clusters within the marine sublineage IV of Nitrospira, though most sequences clustered with the type strain of Nitrospira marina and with a strain isolated from a marine RAS. Three lipids dominated the whole fatty acid profiles of nitrite-oxidizing marine and brackish enrichments of Nitrospira sublineage IV organisms. The membranes included two marker lipids (16∶1 cis7 and 16∶1 cis11 combined with the non-specific acid 16∶0 as major compounds and confirmed these marker lipids as characteristic for sublineage IV species. The predominant labeling of these characteristic fatty acids and the phylogenetic sequence analyses of the marine Nitrospira sublineage IV identified organisms of this sublineage as main autotrophic nitrite-oxidizers in the investigated brackish biofilter systems.

Ammonia-nitrogen and Phosphate Reduction by Bio-Filter using Factorial Design

Science.gov (United States)

Kasmuri, Norhafezah; Ashikin Mat Damin, Nur; Omar, Megawati

2018-02-01

Untreated landfill leachate is known to have endangered the environment. As such new treatment must be sought to ensure its cost-effective and sustainable treatment. Thus this paper reports the effectiveness of bio-filter to remove pollutants. In this research, the reduction of nutrients concentration was evaluated in two conditions: using bio-filter and without bio-filter. Synthetic wastewater was used in the batch culture. It was conducted within 21 days in the initial mediums of 100 mg/L ammonia-nitrogen. The nitrification medium consisted of 100 mg/L of ammonia-nitrogen while the nitrite assay had none. The petri dish experiment was also conducted to observe the existence of any colony. The results showed 22% of ammonia- nitrogen reduction and 33% phosphate in the nitrification medium with the bio-filter. The outcome showed that the bio-filter was capable to reduce the concentration of pollutants by retaining the slow growing bacteria (AOB and NOB) on the plastic carrier surface. The factorial design was applied to study the effect of the initial ammonia-nitrogen concentration and duration on nitrite-nitrogen removal. Finally, a regression equation was produced to predict the rate of nitrite-nitrogen removal without conducting extended experiments and to reduce the number of trials experiment.

Removal of benzene under acidic conditions in a controlled Trickle Bed Air Biofilter.

Science.gov (United States)

Hassan, Ashraf Aly; Sorial, George A

2010-12-15

Trickle Bed Air Biofilters (TBABs) are considered to be economical and environmental-friendly for treatment of Volatile Organic Compounds (VOCs). Hydrophilic VOCs are easily degradable while hydrophobic ones pose a great challenge for adequate treatment due to the transfer of the VOC to the liquid phase. In this study the utilization of acidic pH is proposed for the treatment of benzene vapors. The acidic pH would encourage the growth of fungi as the main consortium. A TBAB operated at pH 4 was used for the treatment of an air stream contaminated with benzene under different loading rates ranging from 37 to 76.8 g/(m(3)h). The purpose of introducing fungi was to compare the performance with traditional TBAB operating under neutral pH in order to assess the biodegradation of benzene in mixtures with other compounds favoring acidic conditions. The experimental plan was designed to assess long-term performance with emphasis based on different benzene loading rates, removal efficiency with TBAB depth, and carbon mass balance closure. At benzene loading rate of 64 g/(m(3)h), the removal efficiency was 90%. At the maximum loading rate of 77 g/(m(3)h), the removal efficiency was 75% marking the maximum elimination capacity for the TBAB at 58.8 g/(m(3)h). Operating at acidic pH successfully supported the degradation of benzene in TBAB. It is worthwhile to note that benzene appears in mixtures with n-hexane and toluene, which are reported to be better degraded under such conditions. Copyright © 2010 Elsevier B.V. All rights reserved.

EFEKTIVITAS SISTEM BIOFILTER AEROB DALAM MENURUNKAN KADAR AMONIA PADA AIR LIMBAH

Directory of Open Access Journals (Sweden)

Ni Made Indra Wahyuni

2015-06-01

Full Text Available The increasingpopulationand activity of the Balinese people can increase the amount of waste as a byproduct of community activities. The presence of the metabolites in wastewater as ammonia is toxic to aquatic organisms. Application aerobic biofilter system can be used as an attempt to reduce levels of ammonia. In the aerobic biofilter, contact between the gravel media with microorganisms that form biofilmsare able to accelerate the degradation of organic matter and nitrification processes. The aims of this research are to determine the best consortium of activated sludge to reduce ammonia levels by aerobic biofilter system and to determine the effectivity of aerobic biofilter system. The first stage of this research were seeding of activated sludge from three sources are Wastewater Treatment Plan (WWTP of Suwung Denpasar, WWTP of Wangaya Hospital and WWTP of Bali Tourism Development Corporation (BTDC Nusa Dua Bali, for six days. This research was done by measuring Volatile Suspended Solid (VSS value that showed the growth rate of biomass in activated sludge. The second stage wereapplication of activated sludges and control in aerobic biofilter to reduce ammonia levels, for five days. This study used a Completely Randomized Design with four treatments and three repetitions. The results showed that the best activated sludge obtained from WWTP of Suwung Denpasar indicated by the highest biomass growth (VSS value of 2396.6 mg/L and was able to reduce ammonia up to 0.78 mg/ L. The effectivity of aerobic biofilter system with activated sludge from WWTP of Suwung Denpasar achieve effectivity of treatment process up to 92.20 % and have been able to pass the effectivity of quality standards (90% during five days of processing. The effectivity levels was the highest compared to control and activated sludgetreatments.

Filter bed systems treating domestic wastewater in the Nordic countries - Performance and reuse of filter media

DEFF Research Database (Denmark)

Jenssen, Petter D.; Krogstad, T.; Paruch, A.M.

2010-01-01

Nine filter beds have been constructed in the Nordic countries, Denmark, Finland, Norway and Sweden. Filter beds consist of a septic tank followed by an aerobic pre-treatment biofilter and a subsequent saturated flow grass-covered filter. Thus, filter beds are similar to subsurface flow construct...

Pengolahan Limbah Rumah Makan dengan Proses Biofilter Aerobik

Directory of Open Access Journals (Sweden)

Laily Zoraya Zahra

2015-03-01

Full Text Available Berkembangnya rumah makan/restoran yang semakin pesat dapat dipastikan akan turut menambah buangan air limbah domestik dengan kadar organik yang tinggi dalam jumlah yang tidak sedikit yang dibuang ke badan air.Tingginya kadar organik dalam limbah domestik rumah makan akan menyebabkan aroma yang tidak sedap jika tidak ada pengolahan terlebih dahulu, maka pengolahan yang dapat digunakan untuk mengolah air limbah rumah makan tersebut adalah proses biofilter aerobik. Penelitian dilakukan dengan proses biofilter aerobik dengan aliran downflow dan menggunakan sistem intermitten.Variabel dalam penelitian ini adalah media biofilter berupa kerikil dan batu alam serta Hydraulic Retention Time (HRT 8 jam. Parameter pencemar yang diukur efisiensinya adalah BOD, COD, dan TSS. Besarnya penyisihan parameter BOD, COD dan TSS dengan menggunakan biofilter aerob berturut-turut mencapai 94,83%, 92,95%, dan 95%. Reaktor paling baik dalam mengolah air limbah adalah reaktor biofilter dengan media kerikil pada HRT 8 jam.

DEGRADATION OF AROMATIC COMPOUNDS USING MOVING BED BIOFILM REACTORS

Directory of Open Access Journals (Sweden)

B. Ayati, H. Ganjidoust, M. Mir Fattah

2007-04-01

Full Text Available For biological treatment of water, there are many different biofilm systems in use. Examples of them are trickling filters, rotating biological contactors, fixed media submerged biofilters, granular media biofilters and fluidized bed reactors. They all have their advantages and disadvantages. Hence, the Moving Bed Biofilm Reactor process was developed in Norway in the late 1980s and early 1990s to adopt the best features of the activated sludge process as well as those of the biofilter processes, without including the worst. Two cylindrical moving bed biofilm reactors were used in this study working in upflow stream conditions. Experiments have been done in aerobic batch flow regime. Laboratory experiments were conducted at room temperature (23–28C and synthetic wastewater comprising a composition of phenol and hydroquinone in each reactor as the main organic constituents, plus balanced nutrients and alkalinity were used to feed the reactor. The ratio of influent to effluent COD was determined at different retention times. The results indicated that the removal efficiency of each selected compound is affected by the detention time. At low phenol and hydroquinone concentration (from 700 to 1000 mg/L maximum removal efficiency (over 80 % was obtained. By further increasing in COD loading rate up to 3000 mg/L, a decrease in COD removal rate was occurred. In the reactor containing pyrogallol in COD of 1500 mg/L, the removal rate decreased to 10 percent because of its toxicity for microorganisms.

Research on the Aerodynamic Resistance of Trickle Biofilter

Directory of Open Access Journals (Sweden)

Alvydas Zagorskis

2011-12-01

Full Text Available A four – section trickle biofilter was constructed for experimental research. The filter was filled with the packing material of artificial origin. The material consists of plastic balls having a large surface area. The dependence of biofilter aerodynamic resistance on supply air flow rate and the number of filter sections was determined. The aerodynamic resistance of the biofilter was measured in two cases. In the first case, the packing material of the filter was dry, whereas in the second case it was wet. The experimental research determined that an increase in the air flow rate from 0.043 m/s to 0.076 m/s causes an increase in biofilter aerodynamic resistance from 30.5 to 62.5 Pa after measuring four layers of dry packing material. In case of wet packing material, biofilter aerodynamic resistance after measuring four layers of plastic balls increases from 42.1 to 90.4 Pa.Article in Lithuanian

Sulfide oxidation in a biofilter

DEFF Research Database (Denmark)

Pedersen, Claus Lunde; Dezhao, Liu; Hansen, Michael Jørgen

Observed hydrogen sulfide uptake rates in a biofilter treating waste air from a pig farm were too high to be explained within conventional limits of sulfide solubility, diffusion in a biofilm and bacterial metabolism. Clone libraries of 16S and 18S rRNA genes from the biofilter found no sulfide...... higher hydrogen sulfide uptake followed by oxidation catalyzed by iron-containing enzymes such as cytochrome c oxidase in a process uncoupled from energy conservation....

Sulfide oxidation in a biofilter

DEFF Research Database (Denmark)

Pedersen, Claus Lunde; Liu, Dezhao; Hansen, Michael Jørgen

2012-01-01

Observed hydrogen sulfide uptake rates in a biofilter treating waste air from a pig farm were too high to be explained within conventional limits of sulfide solubility, diffusion in a biofilm and bacterial metabolism. Clone libraries of 16S and 18S rRNA genes from the biofilter found no sulfide...... higher hydrogen sulfide uptake followed by oxidation catalyzed by iron-containing enzymes such as cytochrome c oxidase in a process uncoupled from energy conservation....

INDUSTRIAL GAS PURIFICATION USE OF BIOFILTERS

Directory of Open Access Journals (Sweden)

Irina Ramona PECINGINĂ

2012-05-01

Full Text Available Biological filtration systems is one of the current alternatives to remove residual volatile components of the air through biological means, without affecting the natural environment. Biofilters have a technology that uses microorganisms (bacteria to treat emissions, in a secure economic and environmental quality. Biofilters consist of porous filters, which is distributed flue gas stream

Efficient Total Nitrogen Removal in an Ammonia Gas Biofilter through High-Rate OLAND

DEFF Research Database (Denmark)

De Clippeleir, Haydée; Courtens, Emilie; Mosquera, Mariela

2012-01-01

Ammonia gas is conventionally treated in nitrifying biofilters; however, addition of organic carbon to perform post-denitrification is required to obtain total nitrogen removal. Oxygen-limited autotrophic nitrification/denitrification (OLAND), applied in full-scale for wastewater treatment, can...... offer a cost-effective alternative for gas treatment. In this study, the OLAND application thus was broadened toward ammonia loaded gaseous streams. A down flow, oxygen-saturated biofilter (height of 1.5 m; diameter of 0.11 m) was fed with an ammonia gas stream (248 ± 10 ppmv) at a loading rate of 0...... at water flow rates of 1.3 ± 0.4 m3 m–2 biofilter section d–1. Profile measurements revealed that 91% of the total nitrogen activity was taking place in the top 36% of the filter. This study demonstrated for the first time highly effective and sustainable autotrophic ammonia removal in a gas biofilter...

Exploring the potential of fungi for methane abatement: Performance evaluation of a fungal-bacterial biofilter.

Science.gov (United States)

Lebrero, Raquel; López, Juan Carlos; Lehtinen, Iiro; Pérez, Rebeca; Quijano, Guillermo; Muñoz, Raúl

2016-02-01

Despite several fungal strains have been retrieved from methane-containing environments, the actual capacity and role of fungi on methane abatement is still unclear. The batch biodegradation tests here performed demonstrated the capacity of Graphium sp. to co-metabolically biodegrade methane and methanol. Moreover, the performance and microbiology of a fungal-bacterial compost biofilter treating methane at concentrations of ∼2% was evaluated at empty bed residence times of 40 and 20 min under different irrigation rates. The daily addition of 200 mL of mineral medium resulted in elimination capacities of 36.6 ± 0.7 g m(-3) h(-1) and removal efficiencies of ≈90% at the lowest residence time. The indigenous fungal community of the compost was predominant in the final microbial population and outcompeted the inoculated Graphium sp. during biofilter operation. Copyright © 2015 Elsevier Ltd. All rights reserved.

The influence of temperature and salt on metal and sediment removal in stormwater biofilters.

Science.gov (United States)

Søberg, Laila C; Viklander, Maria; Blecken, Godecke-Tobias

2014-01-01

Stormwater biofilters are used to treat stormwater runoff. In countries with cold winter climates, biofilters are subject to low temperatures which, in some cases, are combined with potentially high salt concentrations from road de-icing, potentially affecting the biofilter's performance. Since stormwater biofilters have been developed without consideration of their critical winter use, a laboratory study was carried out to evaluate the performance of stormwater biofilters subjected to low and high temperatures, with and without salt. Both factors and their interaction had a significant effect on outflow concentrations and removal percentages. Salt had a negative impact on outflow concentrations, causing lower removal percentages for (especially dissolved) metals, this impact being most pronounced for Cu and Pb. The unrealistic combination of salt with high temperature seemed to further amplify the negative impacts of salt despite the fact that temperature alone did not cause significant differences in outflow concentrations and removal percentages. Still, biofilters showed the ability to treat stormwater efficiently under the simulated winter conditions; outflow concentrations for total metals as a minimum met the class 4 threshold value defined in the Swedish freshwater quality guidelines, while inflow concentrations clearly exceeded the threshold value for class 5. The relatively coarse filter material (which is recommended to facilitate infiltration during winter) did not seem to exacerbate biofilter performance.

Performance of a pilot-scale compost biofilter treating gasoline vapor

International Nuclear Information System (INIS)

Wright, W.F.; Schroeder, E.D.; Chang, D.P.Y.

1997-01-01

A pilot-scale compost biofiltration system was operated as gasoline soil vapor extraction site in Hayward, California for one year. The media was composed of equal volumes of compost and perlite, a bulking agent. Supplements added included nitrogen (as KNO 3 ), a gasoline degrading microbial inoculum, buffer (crushed oyster shell), and water. The biofiltration system was composed of four identical units with outside dimensions of 1.2 x 1.2 x 1.2 m (4 x 4 x 4 ft) operated in an up-flow mode. The units were configured in parallel during the first eight months and then reconfigured to two parallel systems of two units in series. Air flux values ranged from 0.29 to 1.0 m 3 /m 2 per min. Inlet total petroleum hydrogen hydrocarbon (TPH gas ) concentrations ranged from 310 to 2,700 mg/m 3 . The average empty bed contact time was 2.2 min. Following start-up, performance of the individual biofilters varied considerably for a seven-month period. The principal factor affecting performance appeared to be bed moisture content. Overall TPH gas removals reached 90% for short periods in one unit, and BTEX removals were typically above 90%. Drying resulted in channeling and loss of bed activity. Management of bed moisture content improved over the study period, and recovery of system performance was achieved without replacement of bed media. Overall TPH gas removals exceeded 90% during the final 50 days of the study

Utilization of toxic and vapors as alternate electron acceptors in biofilters

Energy Technology Data Exchange (ETDEWEB)

Lee, B.D.; Apel, W.A.; Walton, M.R.

1997-08-01

Conceptually, biofilters are vapor phase bioreactors that rely on microorganisms in the bed medium to oxidize contaminants in off-gases flowing through the bed to less hazardous compounds. In the most studied and utilized systems reduced compounds such as fuel hydrocarbons are enzymatically oxidized to compounds such as carbon dioxide and water. In these types of reactions the microorganisms in the bed oxidize the contaminant and transfer the electrons to oxygen which is the terminal electron acceptor in the process. In essence the contaminant is the carbon and energy source for the microorganisms in the bed medium and through this catabolic process oxygen is reduced to water. An example of this oxidation process can be seen during the degradation of benzene and similar aromatic compounds. Aromatics are initially attacked by a dioxygenase enzyme which oxidizes the compounds to a labile dihydrodiole which is spontaneously converted to a catechol. The dihydroxylated aromatic rings is then opened by oxidative {open_quotes}ortho{close_quotes} or {open_quotes}meta{close_quotes} cleavage yielding cis, cis-muconic acid or 2-hydroxy-cis, cis-muconic semialdehyde, respectively. These organic compounds are further oxidized to carbon dioxide or are assimilated for cellular material. This paper describes the conversion of carbon tetrachloride using methanol as the primary carbon and energy source.

Investigation of efficiency of air cleaning from acetone using a segmental construction biofilter

Directory of Open Access Journals (Sweden)

Denas Bacevičius

2015-10-01

Full Text Available Volatile organic compounds, e. g. acetone, have a direct impact on climate change, decrease of ozone in the air, and on the growth of greenhouse effect. One of the most popular air purifying methods from VOC is a biological air cleaning. Experimental investigations were conducted to determine the efficiency of the new structure of biofilter with polypropylene plates segments. During the investigations the efficiency of segmental construction biofilter of air purification at different initial concentrations of pollutants was determined. Different concentrations of pollutants were estimated during the acetone dilution with water. During the tests the efficiency of biofilter air purification from acetone vapor and its change under different concentrations of vapors was set. Based on test results, the maximum efficiency of biofilter air purification was up to 93%. Studies have shown that increasing the allowable pollutant concentration, the efficiency of air purification unit decreases. Increasing the concentration of supplied acetone vapor into the biofilter from 232 to 701 mg/m3, cleaning efficiency decreased from 92.8 to 82.3%. Since microorganisms fail to oxidize organic compounds, the filter works better at lower initial concentrations of pollutants.

Pollution Removal Performance of Laboratory Simulations of Sydney’s Street Stormwater Biofilters

Directory of Open Access Journals (Sweden)

James Macnamara

2017-11-01

Full Text Available The City of Sydney is constructing more than 21,000 square metres of street biofilter units (raingardens in terms of their Decentralised Water Master Plan (DWMP, for improving the quality of stormwater runoff to Port Jackson, the Cooks River, and the historical Botany Bay. Recharge of the Botany Sand Beds aquifer, currently undergoing remediation by extraction of industrial chlorinated hydrocarbon pollutants, is also envisaged. To anticipate the pollution removal efficiency of field biofilter designs, laboratory soil-column simulations were developed by Western Sydney University partnered with the City. Synthetic stormwater containing stoichiometric amounts of high-solubility pollutant salts in deionised water was passed through 104 mm columns that were layered to simulate monophasic and biphasic field designs. Both designs met the City’s improvement targets for total nitrogen (TN and total phosphorus (TP, with >65% median removal efficiency. Prolonged release of total suspended solids (SS on startup emphasised the need for specifications and testing of proprietary fills. Median removal efficiency for selected heavy metal ecotoxicants was >75%. The researchers suggested that Zinc be added to the targets as proxy for metals, polycyclic aromatic hydrocarbons (PAH and oils/greases co-generated during road use. Simulation results suggested that field units will play an important role in meeting regional stormwater improvement targets.

Phaeobacter grown in biofilters: a new strategy for the control of Vibrionaceae in aquaculture

DEFF Research Database (Denmark)

Prol García, María Jesús; Gomez, Marina; Sanchez, Lorenzo

2014-01-01

materials, but a multilayer biofilm was only observed in the ceramic biofilters. In sterile seawater, plastic and ceramic biofilters reduced Vibrio anguillarum and V. splendidus concentration in one-two Log after 24-48h, showing 10(2)-10(3)CFUmL(-1). Sintered glass biofilters only inactivated V. anguillarum...... showed the lowest detachment and, after 11days, Phaeobacter (10(6) bacteria center dot cm(-3)) covered more than 80% of biofilters total culturable bacteria. DGGE profiles showed that Phaeobacter biofilters stabilizes the green seawater bacterial microbiota....

Dracaena marginata biofilter: design of growth substrate and treatment of stormwater runoff.

Science.gov (United States)

Vijayaraghavan, K; Praveen, R S

2016-01-01

The purpose of this research was to investigate the efficiency of Dracaena marginata planted biofilters to decontaminate urban runoff. A new biofilter growth substrate was prepared using low-cost and locally available materials such as red soil, fine sand, perlite, vermiculite, coco-peat and Sargassum biomass. The performance of biofilter substrate was compared with local garden soil based on physical and water quality parameters. Preliminary analyses indicated that biofilter substrate exhibited desirable characteristics such as low bulk density (1140 kg/m(3)), high water holding capacity (59.6%), air-filled porosity (7.82%) and hydraulic conductivity (965 mm/h). Four different biofilter assemblies, with vegetated and non-vegetated systems, were examined for several artificial rain events (un-spiked and metal-spiked). Results from un-spiked artificial rain events suggested that concentrations of most of the chemical components in effluent were highest at the beginning of rain events and thereafter subsided during the subsequent rain events. Biofilter growth substrate showed superior potential over garden soil to retain metal ions such as Al, Fe, Cu, Cr, Ni, Zn, Cd and Pb during metal-spiked rain events. Significant differences were also observed between non-vegetated and vegetated biofilter assemblies in runoff quality, with the latter producing better results.

Microbiological and kinetic aspects of a biofilter for the removal of toluene from waste gases

Science.gov (United States)

Acuna; Perez; Auria; Revah

1999-04-20

Microbiological and kinetic aspects of a biofilter inoculated with a consortium of five bacteria and two yeast adapted to remove toluene vapors were investigated. Initially the toluene sorption isotherm on peat and the effect of different environmental conditions on the toluene consumption rates of this consortium were measured. The fast start-up of the biofilter and the decay in the elimination capacity (EC) were reproduced using microcosm assays with toluene successive additions. Nutrient limitation and a large degree of heterogeneity were also detected. EC values, extrapolated from microcosms, were higher than biofilter EC when it was operating close to 100% efficiency but tended to relate better as the biofilter EC diminished. In studies on the microbial evolution in the biofilter, an increase in the cell count and variation in the ecology of the consortium were noted. Bacterial counts up to 10 x 10(11) cfu/gdry peat were found in 88 days, which corresponds to about a 10(4) increase from inoculum. Observations with SEM showed a nonuniform biofilm development on the support and the presence of an extracellular material. The results obtained in this work demonstrated that activity measurement in microcosms concomitant to the biofilter operation could be an important tool for understanding, predicting and improving the biofiltration performance. Copyright 1999 John Wiley & Sons, Inc.

Styrene biofiltration in a trickle-bed reactor

Directory of Open Access Journals (Sweden)

V. Novak

2008-04-01

Full Text Available The biological treatment of styrene waste gas in a trickle-bed filter (TBF was investigated. The bioreactor consisted of a two-part glass cylinder (ID 150 mm filled with 25 mm polypropylene Pall rings serving as packing material. The bed height was 1m. Although the laboratory temperature was maintained at 22 ºC, the water temperature in the trickle-bed filter was slightly lower (about 18 ºC.The main aim of our study was to observe the effect of empty-bed residence time (EBRT on bioreactor performance at a constant pollutant concentration over an extended time period. The bioreactor was inoculated with a mixed microbial consortium isolated from a styrene-degrading biofilter that had been running for the previous two years. After three weeks of acclimation period, the bioreactor was loaded with styrene (100 mg.m-3. EBRT was in the range of 53 s to 13 s. A maximum elimination capacity (EC of 11.3 gC.m-3.h-1 was reached at an organic loading (OL rate of 18.6 gC.m-3.h-1.

Modelling of suspended matter transport and turnover in biofilters for waste water treatment; Modellierung von Stofftransport und -umsatz in Biofiltern zur Abwasserreinigung

Energy Technology Data Exchange (ETDEWEB)

Telgmann, U. [Kassel Univ. (Gesamthochschule) (Germany). Fachgebiet Siedlungswasserwirtschaft; Horn, H. [Fachhochschule Magdeburg (Germany). Hydro- und Abfallchemie

1999-07-01

Essential elements of the presented model for biofilters are suspended matter transfer in the boundary layer water/biofilm, the gradient of concentration for substrate turnover in the biofilm with limited diffusion, and the gradient of concentration and biomass distribution both in the biofilm and over the height of the reactor. Problematic in biofilm modelling is linking the turnover of substrate in the biofilm affixed to the carrier material with changes in concentration along the reactor height. This means that concentration profiles need to be calculated both in the biofilm and over the height of the reactor. The presented model describes substrate turnover in the biofilm by means of a Monod kinetics, and diffusive suspended matter transport with the aid of Fick's second law. The change in concentration over the filter bed height is taken into account by dividing the reactor volume into five complete-mixing segments. Further elements of modelling are biomass production and the corresponding discharge from the biofilter. In exemplary manner, a biofilter for downstream denitrification with methanol was modelled and the results were compared with measurements taken at a semi-technical pilot plant. (orig.) [German] Wesentliche Elemente des hier vorgestellten Modells fuer Biofilter sind der Stoffuebergang in der Grenzschicht Wasser/Biofilm, der Konzentrationsgradient beim diffusionslimitierten Substratumsatz im Biofilm, der Konzentrationsgradient und die Biomasseverteilung sowohl im Biofilm als auch ueber die Reaktorhoehe. Problematik bei der Modellierung eines Biofilms ist die Verknuepfung von Substratumsatz in dem auf dem Traegermaterial haftenden Biofilm mit der Konzentrationsveraenderung entlang der Reaktorhoehe. Die Konzentrationsprofile muessen also sowohl im Biofilm als auch ueber die Reaktorhoehe berechnet werden. Im praesentierten Modell wird der Substratumsatz im Biofilm mit einer Monodkinetik und der diffusive Stofftransport mit Hilfe des 2. Fick

Evaluation of dispersion methods for enumeration of microorganisms from peat and activated carbon biofilters treating volatile organic compounds.

Science.gov (United States)

Khammar, Nadia; Malhautier, Luc; Degrange, Valérie; Lensi, Robert; Fanlo, Jean-Louis

2004-01-01

To enumerate microorganisms having colonized biofilters treating volatile organic compounds, it is necessary firstly to evaluate dispersion methods. Crushing, shaking and sonication were then tested for the removal of microflora from biofilters packing materials (peat and activated carbon). Continuous or discontinuous procedures, and addition of glass beads had no effect on the number of microorganisms removed from peat particles. The duration of treatment also had no effect for shaking and crushing, but the number of microorganisms after 60 min of treatment with ultrasound was significantly higher than that obtained after 0.5 min. The comparison between these methods showed that crushing was the most efficient for the removal of microorganisms from both peat and activated carbon. The comparison between three chemical dispersion agents showed that 1% Na-pyrophosphate was less efficient, compared with 200 mM phosphate buffer or 1% Na-hexametaphosphate. To optimize the cultivation of microorganisms, three different agar media were compared. Tryptic soy agar tenfold diluted (TSA 1/10) was the most suitable medium for the culture of microflora from a peat biofilter. For the activated carbon biofilter, there was no significant difference between Luria Bertoni, TSA 1/10, and plate count agar. The optimized extraction and enumeration protocols were used to perform a quantitative characterization of microbial populations in an operating laboratory activated carbon biofilter and in two parallel peat biofilters.

Biological elimination of volatile, organic compounds from waste gases in a biofilter

Energy Technology Data Exchange (ETDEWEB)

Wu, G.; Chabot, J.C.; Caron, J.J.; Heitz, M. [Universite de Sherbrooke, Sherbrooke, PQ (Canada). Dept. de Genie Chimique

1998-01-01

A great deal of research has been directed towards the problem of reduction and control of volatile organic compounds (VOCs). The aim of this research is to find a process that is both efficient and inexpensive in comparison with traditional air treatment technologies. The biofilter used, a one stage system, 2 m in height, is an aerobic system for waste gases containing VOC`s using the degradation properties of microbial flora (assorted cultures of Bacillus, Micrococcus, Acinetobacter and yeast). In this process, polluted gas diffuses across a filter bed into which a microbial culture has previously been introduced. Peat is the medium of choice for inoculation with microorganisms because of its adsorption and absorption properties, ability to retain moisture, and buffering capacity. Furthermore, the peat utilized is spherical in shape; thus, it is possible to avoid problems related to compacting. The objective of this study was to eliminate VOCs emitted from a rotogravure process. The team was able to achieve promising results from biofiltration of two types of VOCs (a mixed solvent containing isopropyl acetate and 1-nitropropane, and the solvent: 1-nitropropane). The results obtained indicate that the elimination of nitropropane and the mixed solvent in the biofilter are considered to follow zero-order kinetics with reaction rate limitation and diffusion rate limitation, respectively. 8 refs., 5 figs.

Biofilter design for effective nitrogen removal from stormwater - influence of plant species, inflow hydrology and use of a saturated zone.

Science.gov (United States)

Payne, Emily G I; Pham, Tracey; Cook, Perran L M; Fletcher, Tim D; Hatt, Belinda E; Deletic, Ana

2014-01-01

The use of biofilters to remove nitrogen and other pollutants from urban stormwater runoff has demonstrated varied success across laboratory and field studies. Design variables including plant species and use of a saturated zone have large impacts upon performance. A laboratory column study of 22 plant species and designs with varied outlet configuration was conducted across a 1.5-year period to further investigate the mechanisms and influences driving biofilter nitrogen processing. This paper presents outflow concentrations of total nitrogen from two sampling events across both 'wet' and 'dry' frequency dosing, and from sampling across two points in the outflow hydrograph. All plant species were effective under conditions of frequent dosing, but extended drying increased variation between species and highlighted the importance of a saturated zone in maintaining biofilter function. The saturated zone also effectively treated the volume of stormwater stored between inflow events, but this extended detention provided no additional benefit alongside the rapid processing of the highest performing species. Hence, the saturated zone reduced performance differences between plant species, and potentially acts as an 'insurance policy' against poor sub-optimal plant selection. The study shows the importance of biodiversity and inclusion of a saturated zone in protecting against climate variability.

Modelling and simulation of a nitrification biofilter for drinking water ...

African Journals Online (AJOL)

For the purification of pure and microbiologically safe drinking water, different treatment steps are necessary. One of those steps is the removal of ammonium, which can, e.g. be accomplished through nitrification in a biofilter. In this study, a model for such a nitrifying biofilter was developed and the model was ...

The effect of nitrate on ethylene biofiltration

International Nuclear Information System (INIS)

Lee, Sang-Hun; Li, Congna; Heber, Albert J.

2012-01-01

Highlights: ► Ethylene biofiltration strongly depends on nitrate concentrations and media types. ► We examine reduced N supply can increase ethylene removals in biofilters. ► Perlite medium is better for ethylene biofiltration than activated carbon medium. - Abstract: This study investigated the effects of filter media types and nitrate (NO 3 − ) concentrations in nutrient solutions on C 2 H 4 biofiltration. A new nutrient solution with zero NO 3 − concentration was supplied to two perlite-bed biotrickling filters, two perlite-bed biofilters, and two GAC (Granular Activated Carbon)-bed biofilters, while the other with 2 g L −1 of NO 3 − was used for the other two GAC biofilters. All reactors underwent a total test duration of over 175 days with an EBRT (Empty Bed Residence Time) of 30 s, inlet gas flow rate of 7 L min −1 , and inlet C 2 H 4 concentrations of 20–30 mg m −3 . NO 3 − concentration and media type significantly affected the C 2 H 4 removal efficiencies in all types of biofiltration. The perlite media with no NO 3 − achieved C 2 H 4 removal efficiencies 10–50% higher than the others. A NO 3 − concentration as high as 2 g L −1 in the original nutrient solution may act as an inhibitor that suppresses the growth or activity of C 2 H 4 degraders. In addition, the perlite media resulted in higher C 2 H 4 removal efficiencies than GAC media, because the hydrophilic surface of the perlite leads to a higher moisture content and thus to favorable microbial growth.

Performance of low pH biofilters treating a paint solvent mixture: Continuous and intermittent loading

International Nuclear Information System (INIS)

Qi Bing; Moe, William M.

2006-01-01

Two biofilters packed with a reticulated polyurethane foam medium were inoculated with a compost-derived enrichment culture grown under acidic conditions (pH 3.0) and then operated over a period lasting 63 days. Both biofilters were supplied with a humidified gas stream containing a five-component mixture of acetone, methyl ethyl ketone, toluene, ethylbenzene, and p-xylene at a total VOC loading rate 80.3 g m -3 h -1 to simulate treatment of air emissions resulting from manufacture of reformulated paint. One biofilter was operated under continuous loading conditions and the other received intermittent loading with contaminants supplied only 8 h/day. Nutrient solution with pH 3.0 was supplied approximately once per week to provide nitrogen and other nutrients. Data are presented which demonstrate that undefined mixed cultures acclimated at low pH can successfully treat paint solvent mixtures in biofilters. The biofilter receiving continuous loading reached high overall removal efficiency (greater than 90% overall removal) 3 weeks after startup, and performance increased over time reaching overall removal in the range of 97-99% after 50 days. Performance of the intermittently loaded biofilter developed more slowly, requiring 6 weeks to stabilize at an overall removal efficiency in excess of 90%. In both biofilters, ketone components were more rapidly degraded than aromatic components, and removal of aromatic compounds was somewhat unstable even after 2 months of biofilter operation. Scanning electron microscopy (SEM) revealed that fungi dominated the microbial populations in both biofilters

PERANAN MANGROVE SEBAGAI BIOFILTER PENCEMARAN AIR WILAYAH TAMBAK BANDENG TAPAK, SEMARANG (Role of Mangrove as Water Pollution Biofilter in Milkfish Pond, Tapak, Semarang

Directory of Open Access Journals (Sweden)

Nana T.M. Kariada

2014-10-01

Full Text Available ABSTRAK Mangrove yang tumbuh di ujung sungai besar berperan sebagai penampung terakhir bagi limbah dari industri di perkotaan dan perkampungan hulu yang terbawa aliran sungai. Area hutan mangrove mempunyai kemampuan mengakumulasi logam berat yang terdapat dalam ekosistem tempat tumbuhnya. Tujuan yang hendak dicapai dari  penelitian ini adalah mengkaji peranan mangrove sebagai biofilter pencemaran air dan  mengetahui jenis mangrove yang terbaik berperan sebagai biofilter pencemaran air di di lingkungan tambak bandeng Tapak Kota Semarang. Desain yang digunakan dalam penelitian ini adalah deskriptif eksploratif. Berdasarkan hasil penelitian tentang akumulasi logam berat Cu antara air dan sedimen tambak, diperoleh hasil telah terjadi akumulasi Cu dengan Faktor Konsentrasi antara 43-400.  Pada stasiun 3 dan 4 terdapat akumulasi Cu dengan nilai Faktor Konsentrasi 3 dan 0,3. Hal ini menunjukkan akumulasi Cu dari sedimen ke akar mangrove relatif masih kecil. Perbedaan akumulasi dari tiap stasiun penelitian yang diamati menunjukkan adanya perbedaan jenis mangrove yang tumbuh pada masing-masing stasiun penelitian. Mangrove yang berada di lingkungan tambak bandeng wilayah Tapak Kota Semarang disimpulkan dapat berperan sebagai biofilter pencemaran air yang ada di perairan tersebut. Mangrove dari jenis Avicennia marina mempunyai peranan yang lebih baik dari jenis Rhizophora sp sebagai biofilter pencemaran air di lingkungan tambak bandeng Tapak Kota Semarang.   ABSTRACT Mangroves,  that is growing at the end of a great river, has a role as the last place for the waste water from urban and domestic industry at the upstream that were carried by the flow of river. Mangrove area  has  ability to accumulate a heavy metals  which is contained in it. The  goals  from this research is to assess role of mangrove as biofilter of water pollution and to find out the best species of mangrove as biofilter of water pollution in milkifish pond in Tapak, Semarang

Development of a novel biofilter for aerobic biodegradation of volatile organic compounds (VOCs)

International Nuclear Information System (INIS)

Govind, R.; Utgikar, V.; Shan, Y.; Zhao, Wang; Sayles, G.D.; Bishop, D.F.; Safferman, S.I.

1992-01-01

In recent years, the emission into the atmosphere of volatile organic compounds (VOCs) has undergone increased regulation by EPA, OSHA and other government agencies due to potential human health hazards. The sources of these VOCs include releases during industrial production and use, from contaminated wastewaters in collection systems and treatment plants, and from hazardous wastes in landfills and contaminated ground water. Conventional methods for treating VOC emissions include adsorption on solids, absorption in solvents, incineration and catalytic oxidation. One alternative to these conventional treatment methods is the biological destruction of the VOCs in gas phase biofilters. This method has the advantage of pollution destruction (as compared to transfer to another medium) at lower operation and maintenance costs. The biofilter method also can be combined with various stripping or vapor extraction separation processes which effectively transfer VOCs from liquid or solid matrices into the gas phase entering biofilters

Study of performances, stability and microbial characterization of a Sequencing Batch Biofilter Granular Reactor working at low recirculation flow.

Science.gov (United States)

De Sanctis, Marco; Beccari, Mario; Di Iaconi, Claudio; Majone, Mauro; Rossetti, Simona; Tandoi, Valter

2013-02-01

The Sequencing Batch Biofilter Granular Reactor (SBBGR) is a promising wastewater treatment technology characterized by high biomass concentration in the system, good depuration performance and low sludge production. Its main drawback is the high energy consumption required for wastewater recirculation through the reactor bed to ensure both shear stress and oxygen supply. Therefore, the effect of low recirculation flow on the long-term (38 months) performance of a laboratory scale SBBGR was studied. Both the microbial components of the granules, and their main metabolic activities were evaluated (heterotrophic oxidation, nitrification, denitrification, fermentation, sulphate reduction and methanogenesis). The results indicate that despite reduced recirculation, the SBBGR system maintained many of its advantageous characteristics. Copyright © 2012 Elsevier Ltd. All rights reserved.

Potential of Biofilters for Treatment of De-Icing Chemicals

Directory of Open Access Journals (Sweden)

Gema Sakti Raspati

2018-05-01

Full Text Available Organic de-icing chemicals, such as propylene glycol and potassium formate, cause environmental degradation in receiving water if left untreated, due to the high organic load resulting in oxygen depletion. Biofilters are commonly used for the treatment of biodegradable organic carbon in water treatment. This study investigated the potential for using biofilters for treating organic de-icing compounds. Lab-scale adsorption tests using filter media made of crushed clay (Filtralite and granular activated carbon were conducted. Further, a column filtration experiment testing two different crushed clay size ranges was carried out investigating the effect of filter media depth, nutrient addition, and filtration rate. The surrogate parameter used to monitor the removal of de-icing chemicals was dissolved organic carbon (DOC. The adsorption test showed no significant adsorption of DOC was observed. The column test showed that the most active separation occurred in the first ~20 cm of the filter depth. This was confirmed by results from (1 water quality analysis (i.e., DOC removal and adenosine tri-phosphate (ATP measurement; and (2 calculations based on a filtration performance analysis (Iwasaki model and filter hydraulic evaluation (Lindquist diagram. The results showed that, for the highest C:N:P ratio tested (molar ratio of 24:7:1, 50–60% DOC removal was achieved. The addition of nutrients was found to be important for determining the biofilter performance.

A Method for Estimating Mass-Transfer Coefficients in a Biofilter from Membrane Inlet Mass Spectrometer Data

DEFF Research Database (Denmark)

Nielsen, Anders Michael; Nielsen, Lars Peter; Feilberg, Anders

2009-01-01

A membrane inlet mass spectrometer (MIMS) was used in combination with a developed computer model to study and improve management of a biofilter (BF) treating malodorous ventilation air from a meat rendering facility. The MIMS was used to determine percentage removal efficiencies (REs) of selected...... sulfur gases and to provide toluene retention profiles for the model to determine the air velocity and overall mass-transfer coefficient of toluene. The mass-transfer coefficient of toluene was used as a reference for determining the mass transfer of sulfur gases. By presenting the model to scenarios...... of a filter bed with a consortium of effective sulfur oxidizers, the most likely mechanism for incomplete removal of sulfur compounds from the exhaust air was elucidated. This was found to be insufficient mass transfer and not inadequate bacterial activity as anticipated by the manager of the BF. Thus...

Moisture effects on greenhouse gases generation in nitrifying gas-phase compost biofilters.

Science.gov (United States)

Maia, Guilherme D N; Day, George B; Gates, Richard S; Taraba, Joseph L; Coyne, Mark S

2012-06-01

Gas-phase compost biofilters are extensively used in concentrated animal feeding operations to remove odors and, in some cases, ammonia from air sources. The expected biochemical pathway for these predominantly aerobic systems is nitrification. However, non-uniform media with low oxygen levels can shift biofilter microbial pathways to denitrification, a source of greenhouse gases. Several factors contribute to the formation of anoxic/anaerobic zones: media aging, media and particle structure, air velocity distribution, compaction, biofilm thickness, and moisture content (MC) distribution. The present work studies the effects of media moisture conditions on ammonia (NH(3)) removal and greenhouse gas generation (nitrous oxide, N(2)O and methane, CH(4)) for gas-phase compost biofilters subject to a 100-day controlled drying process. Continuous recordings were made for the three gases and water vapor (2.21-h sampling cycle, each cycle consisted of three gas species, and water vapor, for a total of 10,050 data points). Media moisture conditions were classified into three corresponding media drying rate (DR) stages: Constant DR (wetter media), falling DR, and stable-dry system. The first-half of the constant DR period (0-750 h; MC=65-52%, w.b.) facilitated high NH(3) removal rates, but higher N(2)O generation and no CH(4) generation. At the drier stages of the constant DR (750-950 h; MC=52-48%, w.b.) NH(3) removal remained high but N(2)O net generation decreased to near zero. In the falling DR stage (1200-1480 h; MC=44-13%) N(2)O generation decreased, CH(4) increased, and NH(3) was no longer removed. No ammonia removal or greenhouse gas generation was observed in the stable-dry system (1500-2500 h; MC=13%). These results indicate that media should remain toward the drier region of the constant DR (in close proximity to the falling DR stage; MC=50%, approx.), to maintain high levels of NH(3) removal, reduced levels of N(2)O generation, and nullify levels of CH(4

Potential of Biofilters for Treatment of De-Icing Chemicals

OpenAIRE

Raspati, Gema Sakti; Lindseth, Hanna Kristine; Muthanna, Tone Merete; Azrague, Kamal

2018-01-01

Organic de-icing chemicals, such as propylene glycol and potassium formate, cause environmental degradation in receiving water if left untreated, due to the high organic load resulting in oxygen depletion. Biofilters are commonly used for the treatment of biodegradable organic carbon in water treatment. This study investigated the potential for using biofilters for treating organic de-icing compounds. Lab-scale adsorption tests using filter media made of crushed clay (Filtralite) and granular...

Do benthic biofilters contribute to sustainability and restoration of the benthic environment impacted by offshore cage finfish aquaculture?

International Nuclear Information System (INIS)

Aguado-Gimenez, F.; Piedecausa, M.A.; Carrasco, C.; Gutierrez, J.M.; Aliaga, V.; Garcia-Garcia, B.

2011-01-01

Highlights: → Benthic biofilters were deployed under an offshore fish farm and in control locations. → We checked the farm influence on fouling, wild fish and sediment near the biofilters. → Fouling under the cages used fish farm-derived wastes, but at low efficiency. → Wild fish were more abundant in the biofilters located below the cages. → Despite these clear benefits, sediment quality around the biofilters did not improve. - Abstract: Benthic biofilters were deployed under a cage fish farm and in two reference locations to assess the influence of the farm on the biofilters and the surroundings, as well as to verify the usefulness of this technology as a mitigation tool. The biofilters underneath the farm recruited a fouling community practically identical to that of the control biofilters, which included a variety of trophic strategies. The former showed a higher 15 N enrichment, indicating that fouling beneath the farm was benefiting from the farm waste. The waste retention efficiency was low (0.02 g N m -2 month -1 ) beneath the farm. Benthic biofilters aggregated demersal wild fish around and within them. Pelagic wild fish also frequently used the biofilters beneath the farm, forming compact shoals around them. The increased complexity of the habitat below the fish farm enhanced biodiversity, but this improvement did not lead to the recovery of the sediments around the biofilters.

A hybridized membrane-botanical biofilter for improving air quality in occupied spaces

Science.gov (United States)

Llewellyn, David; Darlington, Alan; van Ras, Niels; Kraakman, Bart; Dixon, Mike

Botanical biofilters have been shown to be effective in improving indoor air quality through the removal of complex mixtures of gaseous contaminants typically found in human-occupied environments. Traditional, botanical biofilters have been comprised of plants rooted into a thin and highly porous synthetic medium that is hung on vertical surfaces. Water flows from the top of the biofilter and air is drawn horizontally through the rooting medium. These botanical biofilters have been successfully marketed in office and institutional settings. They operate efficiently, with adequate contaminant removal and little maintenance for many years. Depending on climate and outdoor air quality, botanical biofiltration can substantially reduce costs associated with ventilation of stale indoor air. However, there are several limitations that continue to inhibit widespread acceptance: 1. Current designs are architecturally limiting and inefficient at capturing ambient light 2. These biofilters can add significant amounts of humidity to an indoor space. This water loss also leads to a rapid accumulation of dissolved salts; reducing biofilter health and performance 3. There is the perception of potentially actively introducing harmful bioaerosols into the air stream 4. Design and practical limitations inhibit the entrance of this technology into the lucrative residential marketplace This paper describes the hybridization of membrane and botanical biofiltration technologies by incorporating a membrane array into the rootzone of a conventional interior planting. This technology has the potential for addressing all of the above limitations, expanding the range of indoor settings where botanical biofiltration can be applied. This technology was developed as the CSA-funded Canadian component an ESA-MAP project entitled: "Biological airfilter for air quality control of life support systems in manned space craft and other closed environments", A0-99-LSS-019. While the project addressed a

Investigation of Removal Capacities of Biofilters for Airborne Viable Micro-Organisms

Science.gov (United States)

Soret, Rémi; Fanlo, Jean-Louis; Malhautier, Luc; Geiger, Philippe; Bayle, Sandrine

2018-01-01

New emerging issues appears regarding the possible aerosolization of micro-organisms from biofilters to the ambient air. Traditional bioaerosol sampling and cultural methods used in literature offer relative efficiencies. In this study, a new method revolving around a particle counter capable of detecting total and viable particles in real time was used. This counter (BioTrak 9510-BD) uses laser-induced fluorescence (LIF) technology to determine the biological nature of the particle. The concentration of viable particles was measured on two semi-industrial pilot scale biofilters in order to estimate the Removal Efficiency in viable particles (REvp) in stable conditions and to examine the influence of pollutant feeding and relative humidification of the gaseous effluent on the REvp. The REvp of biofilters reached near 80% and highlighted both the stability of that removal and the statistical equivalence between two identical biofilters. Pollutant deprivation periods of 12 h, 48 h and 30 days were shown to have no influence on the biofilters’ removal capacity, demonstrating the robustness and adaptation capacities of the flora. In contrast, a 90-day famine period turned the biofilters into emitters of viable particles. Finally, the humidification of the effluent was shown to negatively influence the removal capacity for viable particles, as drying off the air was shown to increase the REvp from 60 to 85%. PMID:29562709

The effect of nitrate on ethylene biofiltration

Energy Technology Data Exchange (ETDEWEB)

Lee, Sang-Hun, E-mail: lee323@alumni.purdue.edu [Department of Agricultural and Biological Engineering, Purdue University, 225 South University St., West Lafayette, 47907-2093 IN (United States); Li, Congna; Heber, Albert J. [Department of Agricultural and Biological Engineering, Purdue University, 225 South University St., West Lafayette, 47907-2093 IN (United States)

2012-11-30

Highlights: Black-Right-Pointing-Pointer Ethylene biofiltration strongly depends on nitrate concentrations and media types. Black-Right-Pointing-Pointer We examine reduced N supply can increase ethylene removals in biofilters. Black-Right-Pointing-Pointer Perlite medium is better for ethylene biofiltration than activated carbon medium. - Abstract: This study investigated the effects of filter media types and nitrate (NO{sub 3}{sup -}) concentrations in nutrient solutions on C{sub 2}H{sub 4} biofiltration. A new nutrient solution with zero NO{sub 3}{sup -} concentration was supplied to two perlite-bed biotrickling filters, two perlite-bed biofilters, and two GAC (Granular Activated Carbon)-bed biofilters, while the other with 2 g L{sup -1} of NO{sub 3}{sup -} was used for the other two GAC biofilters. All reactors underwent a total test duration of over 175 days with an EBRT (Empty Bed Residence Time) of 30 s, inlet gas flow rate of 7 L min{sup -1}, and inlet C{sub 2}H{sub 4} concentrations of 20-30 mg m{sup -3}. NO{sub 3}{sup -} concentration and media type significantly affected the C{sub 2}H{sub 4} removal efficiencies in all types of biofiltration. The perlite media with no NO{sub 3}{sup -} achieved C{sub 2}H{sub 4} removal efficiencies 10-50% higher than the others. A NO{sub 3}{sup -} concentration as high as 2 g L{sup -1} in the original nutrient solution may act as an inhibitor that suppresses the growth or activity of C{sub 2}H{sub 4} degraders. In addition, the perlite media resulted in higher C{sub 2}H{sub 4} removal efficiencies than GAC media, because the hydrophilic surface of the perlite leads to a higher moisture content and thus to favorable microbial growth.

Antimicrobial media for passive removal of pathogen by stormwater biofilters

OpenAIRE

Li, Yali

2017-01-01

Stormwater biofilters (designed primarily for nutrient and metal removal) are gaining popularity globally for the treatment of urban stormwater runoff. However, their reported faecal indicator removal efficiency varies from several log to net leaching, and the effluent concentrations rarely meet the requirements for stormwater harvesting. In order to improve the stormwater biofilter design for reliable pathogen treatment, research in three Stages is therefore conducted systematically: identif...

Investigating bacterial populations in styrene-degrading biofilters by 16S rDNA tag pyrosequencing.

Science.gov (United States)

Portune, Kevin J; Pérez, M Carmen; Álvarez-Hornos, F Javier; Gabaldón, Carmen

2015-01-01

Microbial biofilms are essential components in the elimination of pollutants within biofilters, yet still little is known regarding the complex relationships between microbial community structure and biodegradation function within these engineered ecosystems. To further explore this relationship, 16S rDNA tag pyrosequencing was applied to samples taken at four time points from a styrene-degrading biofilter undergoing variable operating conditions. Changes in microbial structure were observed between different stages of biofilter operation, and the level of styrene concentration was revealed to be a critical factor affecting these changes. Bacterial genera Azoarcus and Pseudomonas were among the dominant classified genera in the biofilter. Canonical correspondence analysis (CCA) and correlation analysis revealed that the genera Brevundimonas, Hydrogenophaga, and Achromobacter may play important roles in styrene degradation under increasing styrene concentrations. No significant correlations (P > 0.05) could be detected between biofilter operational/functional parameters and biodiversity measurements, although biological heterogeneity within biofilms and/or technical variability within pyrosequencing may have considerably affected these results. Percentages of selected bacterial taxonomic groups detected by fluorescence in situ hybridization (FISH) were compared to results from pyrosequencing in order to assess the effectiveness and limitations of each method for identifying each microbial taxon. Comparison of results revealed discrepancies between the two methods in the detected percentages of numerous taxonomic groups. Biases and technical limitations of both FISH and pyrosequencing, such as the binding of FISH probes to non-target microbial groups and lack of classification of sequences for defined taxonomic groups from pyrosequencing, may partially explain some differences between the two methods.

THE USE OF BIOFILTERS FOR DEODORISATION OF THE NOXIOUS GASES

Directory of Open Access Journals (Sweden)

Monika Wierzbińska

2015-01-01

Full Text Available One of the methods of deodorization of noxious gases is biofiltration. This method consists of pollutants biodegradation by using micro-organisms, what leads to the formation of nontoxic and innoxious compounds. In comparison with conventional techniques, bio-filtration requires lower investments and exploitation costs, moreover it is nature friendly. This technique is still developing. Scientists have carried out research on the optimization of biofiltration process, biofilters and selecting parameters of purified gases or improving the method of efficiency. However, industrial application of biofilters is still difficult for many reasons. In this paper we present the mechanism of biofiltration process, the parameters and conditions which have to be fulfilled by purified gases, installation structure for gases biofiltration, application field of this method and specific example of exploited biofilters, including practical operational guidelines.

Hexane abatement and spore emission control in a fungal biofilter-photoreactor hybrid unit

Energy Technology Data Exchange (ETDEWEB)

Saucedo-Lucero, J.O. [Department of Chemical Engineering and Environmental Technology, University of Valladolid, Dr. Mergelina s/n, 47011 Valladolid (Spain); IPICyT, Instituto Potosino de Investigación Científica y Tecnológica, División de Ciencias Ambientales, Camino a la Presa San José No. 2055, C.P., 78216 San Luis Potosí (Mexico); Quijano, G. [Department of Chemical Engineering and Environmental Technology, University of Valladolid, Dr. Mergelina s/n, 47011 Valladolid (Spain); Arriaga, S. [IPICyT, Instituto Potosino de Investigación Científica y Tecnológica, División de Ciencias Ambientales, Camino a la Presa San José No. 2055, C.P., 78216 San Luis Potosí (Mexico); Muñoz, R., E-mail: mutora@iq.uva.es [Department of Chemical Engineering and Environmental Technology, University of Valladolid, Dr. Mergelina s/n, 47011 Valladolid (Spain)

2014-07-15

Highlights: • A fungal biofilter/photoreactor was evaluated in terms of hexane and spore removal. • Biofilter supported elimination capacities of ≈35 g m{sup −3} h{sup −1} and CO{sub 2} yields of ≈75%. • The photocatalytic process slightly boosted the hexane abatement performance. • Biofilter emitted fungal spores at concentrations of 2.4 × 10{sup 3}–9.0 × 10{sup 4} CFU m{sup −3}. • Photo-assisted post-treatments resulted in spore deactivation efficiencies of 98%. - Abstract: The performance of a fungal perlite-based biofilter coupled to a post-treatment photoreactor was evaluated over 234 days in terms of n-hexane removal, emission and deactivation of fungal spores. The biofilter and photoreactor were operated at gas residence times of 1.20 and 0.14 min, respectively, and a hexane loading rate of 115 ± 5 g m{sup −3} h{sup −1}. Steady n-hexane elimination capacities of 30–40 g m{sup −3} h{sup −1} were achieved, concomitantly with pollutant mineralization efficiencies of 60–90%. No significant influence of biofilter irrigation frequency or irrigation nitrogen concentration on hexane abatement was recorded. Photolysis did not support an efficient hexane post-treatment likely due to the short EBRT applied in the photoreactor, while overall hexane removal and mineralization enhancements of 25% were recorded when the irradiated photoreactor was packed with ZnO-impregnated perlite. However, a rapid catalyst deactivation was observed, which required a periodic reactivation every 48 h. Biofilter irrigation every 3 days supported fungal spore emissions at concentrations ranging from 2.4 × 10{sup 3} to 9.0 × 10{sup 4} CFU m{sup −3}. Finally, spore deactivation efficiencies of ≈98% were recorded for the photolytic and photocatalytic post-treatment processes. This study confirmed the potential of photo-assisted post-treatment processes to mitigate the emission of hazardous fungal spores and boost the abatement performance of

Evaluation of a cost effective technique for treating aquaculture water discharge using Lolium perenne Lam as a biofilter.

Science.gov (United States)

Nduwimana, André; Yang, Xiang-Long; Wang, Li-Ren

2007-01-01

Wastewater stabilization ponds generate low cost by-products that are useful for agriculture. The utilization of these by-products for soil amendment and as a source of nutrients for plants requires a high level of sanitation and stabilization of the organic matter, to maintain acceptable levels of soil, water and air quality. In this study, two aquaculture wastewater treatment systems; recirculating system and a floating plant bed system were designed to improve the quality of irrigation water in local communities with low income. In both systems the grass species Lolium perenne Lam was used as a plant biofilter while vegetable specie Amaranthus viridis was used to evaluate the performance of the system and the suitability of the phyto-treated water for irrigation. It was found that the harmful material removal rate for recirculating system was 88.9% for TAN (total ammonia nitrogen), 90% for NO2(-)-N, 64.8% for NO3(-)-N while for floating plant bed system 82.7% for TAN, 82% for NO2(-)-N and 60.5% for NO3(-)-N. Comparative analysis of the efficiency of waste element removal between the two systems revealed that both systems performed well, however, plant growth was not robust for floating plant bed system while recirculating system is energy consuming. Although both systems did not attain sufficient levels of TN (total nitrogen) and TP (total phosphorus) load reduction, the treatment with L. perenne remarkably improved the irrigation water quality. A. viridis plants irrigated with the phyto-treated discharge water had lesser concentrations of heavy metals in their tissues compared to those irrigated with untreated discharge. The control plants irrigated with untreated discharge were also found to be highly lignified with few stems and small leaves.

High performance of nitrogen and phosphorus removal in an electrolysis-integrated biofilter.

Science.gov (United States)

Gao, Y; Xie, Y W; Zhang, Q; Yu, Y X; Yang, L Y

A novel electrolysis-integrated biofilter system was developed in this study to evaluate the intensified removal of nitrogen and phosphorus from contaminated water. Two laboratory-scale biofilter systems were established, one with electrolysis (E-BF) and one without electrolysis (BF) as control. The dynamics of intensified nitrogen and phosphorus removal and the changes of inflow and outflow water qualities were also evaluated. The total nitrogen (TN) removal rate was 94.4% in our newly developed E-BF, but only 74.7% in the control BF. Ammonium removal rate was up to 95% in biofilters with or without electrolysis integration with an influent ammonium concentration of 40 mg/L, and the accumulation of nitrate and nitrite was much lower in the effluent of E-BF than that of BF. Thus electrolysis plays an important role in TN removal especially the nitrate and nitrite removal. Phosphorus removal was significantly enhanced, exceeding 90% in E-BF by chemical precipitation, physical adsorption, and flocculation of phosphorus because of the in situ formation of ferric ions by the anodizing of sacrificial iron anodes. Results from this study indicate that the electrolysis integrated biofilter is a promising solution for intensified nitrogen and phosphorus removal.

Role of Thiobacillus thioparus in the biodegradation of carbon disulfide in a biofilter packed with a recycled organic pelletized material.

Science.gov (United States)

Prenafeta-Boldú, Francesc X; Rojo, Naiara; Gallastegui, Gorka; Guivernau, Miriam; Viñas, Marc; Elías, Ana

2014-07-01

This study reports the biodegradation of carbon disulfide (CS2) in air biofilters packed with a pelletized mixture of composted manure and sawdust. Experiments were carried out in two lab-scale (1.2 L) biofiltration units. Biofilter B was seeded with activated sludge enriched previously on CS2-degrading biomass under batch conditions, while biofilter A was left as a negative inoculation control. This inoculum was characterized by an acidic pH and sulfate accumulation, and contained Achromobacter xylosoxidans as the main putative CS2 biodegrading bacterium. Biofilter operation start-up was unsuccessfully attempted under xerophilic conditions and significant CS2 elimination was only achieved in biofilter A upon the implementation of an intermittent irrigation regime. Sustained removal efficiencies of 90-100 % at an inlet load of up to 12 g CS2 m(-3) h(-1) were reached. The CS2 removal in this biofilter was linked to the presence of the chemolithoautotrophic bacterium Thiobacillus thioparus, known among the relatively small number of species with a reported capacity of growing on CS2 as the sole energy source. DGGE molecular profiles confirmed that this microbe had become dominant in biofilter A while it was not detected in samples from biofilter B. Conventional biofilters packed with inexpensive organic materials are suited for the treatment of low-strength CS2 polluted gases (IL biofiltration of recalcitrant compounds has been highlighted.

ASSESSMENT OF ODOUR EMISSIONS FROM AN OPEN BIOFILTER

Directory of Open Access Journals (Sweden)

Marlon Brancher

2014-12-01

Full Text Available Odour annoyances are considered a major cause of public complaints to regulatory agencies regarding air quality and represent a growing social problem, especially in industrialized countries. In view of the need to diagnose odour sources for control and mitigation of possible impacts on communities, was assessed, through a case study, the odorous emissions from an open biofilter. The equipment was responsible for gas treatment generated in the wastewater plant treatment of a textile industry. Sampling was conducted in the inlet duct of the biofilter using direct sampling and on the emission surface (output using a hood (VDI 3477:2004. Samples were stored in plastic bags manufactured in polyvinyl fluoride (Tedlar® and transported to the laboratory, where the odour concentration (in UO m-3 was determined based on the dynamic olfactometry dilution procedure (EN 13725:2003. To calculate the odour emission rate (OER (in UO h-1, the volumetric flow rate (in m3 h-1 was measured in the inlet duct of the biofilter. The values obtained for the efficiency and the OER were 98.7 % and 0.34 x 106 UO h-1, respectively. Comparing the efficiency value with the criterion established by Article 12 of Resolution SEMA No 054:2006 (State of Paraná, Brazil, adopted as reference, the biofiltration system meets the minimum efficiency rating of 85 % required in removing odour.

Start-up of a drinking water biofilter

DEFF Research Database (Denmark)

Ramsay, Loren; Søborg, Ditte; Breda, Inês Lousinha Ribeiro

When virgin filter media is placed in drinking water biofilters, a start-up period of some months typically ensues. During this period, the necessary inorganic coating and bacterial community are established on the filter medium, after which the treated water complies with drinking water criteria...

Autotrophic nitrogen removal process in a potable water treatment biofilter that simultaneously removes Mn and NH4(+)-N.

Science.gov (United States)

Cai, Yan'an; Li, Dong; Liang, Yuhai; Zeng, Huiping; Zhang, Jie

2014-11-01

Ammonia (NH4(+)-N) removal pathways were investigated in a potable water treatment biofilter that simultaneously removes manganese (Mn) and NH4(+)-N. The results indicated a significant loss of nitrogen in the biofilter. Both the completely autotrophic nitrogen removal over nitrite (CANON) process and nitrification were more likely to contribute to NH4(+)-N removal. Moreover, the model calculation results demonstrated that the CANON process contributed significantly to the removal of NH4(+)-N. For influent NH4(+)-N levels of 1.030 and 1.749mg/L, the CANON process contribution was about 48.5% and 46.6%, respectively. The most important finding was that anaerobic ammonia oxidation (ANAMMOX) bacteria were detectable in the biofilter. It is interesting that the CANON process was effective even for such low NH4(+)-N concentrations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Evaluation of the Efficiency of a Biofilter System’s Phenol Removal From Wastewater

Directory of Open Access Journals (Sweden)

Reza Shokoohi

2016-06-01

Full Text Available Phenol is a toxic hydrocarbon that has been found in the wastewater of several industries, including the petroleum and petrochemical industries. The discharge of untreated wastewater from these industries causes environmental pollution, especially in water. The aim of this study was to evaluate the efficiency of phenol removal from wastewater using a biofiltration system. In this experimental study, a cylindrical plexiglass biofilter reactor with an effective volume of 12 liters was used. A total of 30 pcs of plastic grid discs were placed inside the reactor by plastic pipes to maintain the biofilm media in the reactor. The microorganisms used in this study were obtained from the biological sludge of a municipal wastewater treatment plant. The reproduction and adaptation of the microorganisms to 500 mg/L of phenol lasted three months. The effects of pH, phenol, nitrogen, phosphorus, glucose concentration, and hydraulic retention time on the biofilter system’s performance was evaluated. The results of this study showed that in optimal conditions, this system can reduce the phenol concentration from 500 mg/L to zero within about 4 hr. Maximum efficiency occurred in pH = 7, and the proper COD/N/P ratio was 100/10/2, respectively. In general, this biofilter system is capable of removing 500 mg/L of phenol concentrations and an organic load of 4 - 4.5 kg COD/m3.d within 4 - 5 hr. with high efficiency.

Dimethylamine biodegradation by mixed culture enriched from drinking water biofilter.

Science.gov (United States)

Liao, Xiaobin; Chen, Chao; Zhang, Jingxu; Dai, Yu; Zhang, Xiaojian; Xie, Shuguang

2015-01-01

Dimethylamine (DMA) is one of the important precursors of drinking water disinfection by-product N-nitrosodimethylamine (NDMA). Reduction of DMA to minimize the formation of carcinogenic NDMA in drinking water is of practical importance. Biodegradation plays a major role in elimination of DMA pollution in the environment, yet information on DMA removal by drinking water biofilter is still lacking. In this study, microcosms with different treatments were constructed to investigate the potential of DMA removal by a mixed culture enriched from a drinking water biofilter and the effects of carbon and nitrogen sources. DMA could be quickly mineralized by the enrichment culture. Amendment of a carbon source, instead of a nitrogen source, had a profound impact on DMA removal. A shift in bacterial community structure was observed with DMA biodegradation, affected by carbon and nitrogen sources. Proteobacteria was the predominant phylum group in DMA-degrading microcosms. Microorganisms from a variety of bacterial genera might be responsible for the rapid DMA mineralization. Copyright © 2014 Elsevier Ltd. All rights reserved.

Anaerobe-Aerobe Submerged Biofilter Technology for Domestic Waste Water Treatment; Teknologi Biofilter Anaerob-Aerob Tercelup untuk Pengolahan Air Limbah Domestik

Energy Technology Data Exchange (ETDEWEB)

Nusa-Idaman-Said, [The Agency for the Assessment and Application of Technology, Jakarta (Indonesia)

2000-02-15

Water pollution in the big cities in Indonesia, especially in DKI Jakarta has shown serious problems. One of the potential sources of water pollution is domestic wastewater that is wastewater from kitchens, laundry, bathing and toilets. These problems have become more serious since the spreads of sewerage systems are still low, so that domestic, institutional and commercial wastewater cause severe water pollution in many rivers or shallow ground water. Bases on the fact that the progress of development of sewerage system is still low, it is important to develop low cost technology for individual house hold or semi communal wastewater treatment such as using anaerobic and aerobic submerged biofilter. This paper describes alternative technology for treatment of household wastewater or organic wastewater using anaerobic and aerobic submerged biofilter. Using this technology can decrease BOD, COD and Suspended Solids (SS) concentration more than 90 %. (author)

Combined denitrification and phosphorus removal in a biofilter

DEFF Research Database (Denmark)

Falkentoft, Christina Maria; Harremoes, Poul; Mosbæk, Hans

2000-01-01

A lab-scale biofilter was run continuously for 11/2 years for combined denitrification and phosphorus removal. Alternation between anaerobic and anoxic (nitrate) conditions was used to obtain an enriched culture of denitrifying, phosphate accumulating organisms. Batch experiments were performed...

Air purification from TCE and PCE contamination in a hybrid bioreactors and biofilter integrated system.

Science.gov (United States)

Tabernacka, Agnieszka; Zborowska, Ewa; Lebkowska, Maria; Borawski, Maciej

2014-01-15

A two-stage waste air treatment system, consisting of hybrid bioreactors (modified bioscrubbers) and a biofilter, was used to treat waste air containing chlorinated ethenes - trichloroethylene (TCE) and tetrachloroethylene (PCE). The bioreactor was operated with loadings in the range 0.46-5.50gm(-3)h(-1) for TCE and 2.16-9.02gm(-3)h(-1) for PCE. The biofilter loadings were in the range 0.1-0.97gm(-3)h(-1) for TCE and 0.2-2.12gm(-3)h(-1) for PCE. Under low pollutant loadings, the efficiency of TCE elimination was 23-25% in the bioreactor and 54-70% in the biofilter. The efficiency of PCE elimination was 44-60% in the bioreactor and 50-75% in the biofilter. The best results for the bioreactor were observed one week after the pollutant loading was increased. However, the process did not stabilize. In the next seven days contaminant removal efficiency, enzymatic activity and biomass content were all diminished. Copyright © 2013 Elsevier B.V. All rights reserved.

Coal-packed methane biofilter for mitigation of green house gas emissions from coal mine ventilation air.

Science.gov (United States)

Limbri, Hendy; Gunawan, Cindy; Thomas, Torsten; Smith, Andrew; Scott, Jason; Rosche, Bettina

2014-01-01

Methane emitted by coal mine ventilation air (MVA) is a significant greenhouse gas. A mitigation strategy is the oxidation of methane to carbon dioxide, which is approximately twenty-one times less effective at global warming than methane on a mass-basis. The low non-combustible methane concentrations at high MVA flow rates call for a catalytic strategy of oxidation. A laboratory-scale coal-packed biofilter was designed and partially removed methane from humidified air at flow rates between 0.2 and 2.4 L min-1 at 30°C with nutrient solution added every three days. Methane oxidation was catalysed by a complex community of naturally-occurring microorganisms, with the most abundant member being identified by 16S rRNA gene sequence as belonging to the methanotrophic genus Methylocystis. Additional inoculation with a laboratory-grown culture of Methylosinus sporium, as investigated in a parallel run, only enhanced methane consumption during the initial 12 weeks. The greatest level of methane removal of 27.2±0.66 g methane m-3 empty bed h-1 was attained for the non-inoculated system, which was equivalent to removing 19.7±2.9% methane from an inlet concentration of 1% v/v at an inlet gas flow rate of 1.6 L min-1 (2.4 min empty bed residence time). These results show that low-cost coal packing holds promising potential as a suitable growth surface and contains methanotrophic microorganisms for the catalytic oxidative removal of methane.

Removal of hydrogen sulphide from pig house using biofilter with fungi

DEFF Research Database (Denmark)

Hansen, Michael J.; Pedersen, Claus L.; Søgaard Jensen, Louise H.

2018-01-01

was to investigate if this high removal could be due to the presence of fungi. The removal of reduced sulphur compounds in a 600-mm wide cellulose biofilter was measured at depths of 0, 200, 400 and 600 mm and the results compared with estimated fungal hyphae surface area per biofilm area. Over 19 months, removal...... of hydrogen sulphide was measured during periods with and without fungi. The results demonstrate a correlation between the fungal hyphae surface area and the removal of hydrogen sulphide with the highest removal in the first 200 mm of the biofilter and decreasing removal with depth. During periods...... area caused by the hyphae....

Long-term ammonia removal in a coconut fiber-packed biofilter: analysis of N fractionation and reactor performance under steady-state and transient conditions.

Science.gov (United States)

Baquerizo, Guillermo; Maestre, Juan P; Machado, Vinicius C; Gamisans, Xavier; Gabriel, David

2009-05-01

A comprehensive study of long-term ammonia removal in a biofilter packed with coconut fiber is presented under both steady-state and transient conditions. Low and high ammonia loads were applied to the reactor by varying the inlet ammonia concentration from 90 to 260 ppm(v) and gas contact times ranging from 20 to 36 s. Gas samples and leachate measurements were periodically analyzed and used for characterizing biofilter performance in terms of removal efficiency (RE) and elimination capacity (EC). Also, N fractions in the leachate were quantified to both identify the experimental rates of nitritation and nitratation and to determine the N leachate distribution. Results showed stratification in the biofilter activity and, thus, most of the NH(3) removal was performed in the lower part of the reactor. An average EC of 0.5 kg N-NH(3)m(-3)d(-1) was obtained for the whole reactor with a maximum local average EC of 1.7 kg N-NH(3)m(-3)d(-1). Leachate analyses showed that a ratio of 1:1 of ammonium and nitrate ions in the leachate was obtained throughout steady-state operation at low ammonia loads with similar values for nitritation and nitratation rates. Low nitratation rates during high ammonia load periods occurred because large amounts of ammonium and nitrite accumulated in the packed bed, thus causing inhibition episodes on nitrite-oxidizing bacteria due to free ammonia accumulation. Mass balances showed that 50% of the ammonia fed to the reactor was oxidized to either nitrite or nitrate and the rest was recovered as ammonium indicating that sorption processes play a fundamental role in the treatment of ammonia by biofiltration.

Microbial Biotreatment of Actual Textile Wastewater in a Continuous Sequential Rice Husk Biofilter and the Microbial Community Involved

Science.gov (United States)

Lindh, Markus V.; Pinhassi, Jarone; Welander, Ulrika

2017-01-01

Textile dying processes often pollute wastewater with recalcitrant azo and anthraquinone dyes. Yet, there is little development of effective and affordable degradation systems for textile wastewater applicable in countries where water technologies remain poor. We determined biodegradation of actual textile wastewater in biofilters containing rice husks by spectrophotometry and liquid chromatography mass spectrometry. The indigenous microflora from the rice husks consistently performed >90% decolorization at a hydraulic retention time of 67 h. Analysis of microbial community composition of bacterial 16S rRNA genes and fungal internal transcribed spacer (ITS) gene fragments in the biofilters revealed a bacterial consortium known to carry azoreductase genes, such as Dysgonomonas, and Pseudomonas and the presence of fungal phylotypes such as Gibberella and Fusarium. Our findings emphasize that rice husk biofilters support a microbial community of both bacteria and fungi with key features for biodegradation of actual textile wastewater. These results suggest that microbial processes can substantially contribute to efficient and reliable degradation of actual textile wastewater. Thus, development of biodegradation systems holds promise for application of affordable wastewater treatment in polluted environments. PMID:28114377

Microbial Biotreatment of Actual Textile Wastewater in a Continuous Sequential Rice Husk Biofilter and the Microbial Community Involved.

Directory of Open Access Journals (Sweden)

Jörgen Forss

Full Text Available Textile dying processes often pollute wastewater with recalcitrant azo and anthraquinone dyes. Yet, there is little development of effective and affordable degradation systems for textile wastewater applicable in countries where water technologies remain poor. We determined biodegradation of actual textile wastewater in biofilters containing rice husks by spectrophotometry and liquid chromatography mass spectrometry. The indigenous microflora from the rice husks consistently performed >90% decolorization at a hydraulic retention time of 67 h. Analysis of microbial community composition of bacterial 16S rRNA genes and fungal internal transcribed spacer (ITS gene fragments in the biofilters revealed a bacterial consortium known to carry azoreductase genes, such as Dysgonomonas, and Pseudomonas and the presence of fungal phylotypes such as Gibberella and Fusarium. Our findings emphasize that rice husk biofilters support a microbial community of both bacteria and fungi with key features for biodegradation of actual textile wastewater. These results suggest that microbial processes can substantially contribute to efficient and reliable degradation of actual textile wastewater. Thus, development of biodegradation systems holds promise for application of affordable wastewater treatment in polluted environments.

Methanol removal efficiency and bacterial diversity of an activated carbon biofilter.

Science.gov (United States)

Babbitt, Callie W; Pacheco, Adriana; Lindner, Angela S

2009-12-01

Motivated by the need to establish an economical and environmentally friendly methanol control technology for the pulp and paper industry, a bench-scale activated carbon biofiltration system was developed. This system was evaluated for its performance in removing methanol from an artificially contaminated air stream and characterized for its bacterial diversity over time, under varied methanol loading rates, and in different spatial regions of the filter. The biofilter system, composed of a novel packing mixture, provided an excellent support for growth and activity of methanol-degrading bacteria, resulting in approximately 100% methanol removal efficiency for loading rates of 1-17 g/m(3) packing/h, when operated both with and without inoculum containing enriched methanol-degrading bacteria. Although bacterial diversity and abundance varied over the length of the biofilter, the populations present rapidly formed a stable community that was maintained over the entire 138-day operation of the system and through variable operating conditions, as observed by PCR-DGGE methods that targeted all bacteria as well as specific methanol-oxidizing microorganisms. Phylogenetic analysis of bands excised and sequenced from DGGE gels indicated that the biofilter system supported a diverse community of methanol-degrading bacteria, with high similarity to species in the genera Methylophilus (beta-proteobacteria), Hyphomicrobium and Methylocella (both alpha-proteobacteria).

Nitrogen removal capacity and bacterial community dynamics of a Canon biofilter system at different organic matter concentrations.

Science.gov (United States)

García-Ruiz, María J; Maza-Márquez, Paula; González-López, Jesús; Osorio, Francisco

2018-02-01

Three Canon bench-scale bioreactors with a volume of 2 L operating in parallel were configured as submerged biofilters. In the present study we investigated the effects of a high ammonium concentration (320 mgNH 4 + · L -1 ) and different concentrations of organic matter (0, 100 and 400 mgCOD·L -1 ) on the nitrogen removal capacity and the bacterial community structure. After 60 days, the Canon biofilters operated properly under concentrations of 0 and 100 mgCOD·L -1 of organic matter, with nitrogen removal efficiencies up to 85%. However, a higher concentration of organic matter (400 mgCOD·L -1 ) produced a partial inhibition of nitrogen removal (68.1% efficiency). The addition of higher concentrations of organic matter a modified the bacterial community structure in the Canon biofilter, increasing the proliferation of heterotrophic bacteria related to the genera of Thauera, Longilinea, Ornatilinea, Thermomarinilinea, unclassified Chlorobiales and Denitratisoma. However, heterotrophic bacteria co-exist with Nitrosomonas and Candidatus Scalindua. Thus, our study confirms the co-existence of different microbial activities (AOB, Anammox and denitrification) and the adaptation of a fixed-biofilm system to different concentrations of organic matter. Copyright © 2017 Elsevier Ltd. All rights reserved.

Coal-Packed Methane Biofilter for Mitigation of Green House Gas Emissions from Coal Mine Ventilation Air

Science.gov (United States)

Limbri, Hendy; Gunawan, Cindy; Thomas, Torsten; Smith, Andrew; Scott, Jason; Rosche, Bettina

2014-01-01

Methane emitted by coal mine ventilation air (MVA) is a significant greenhouse gas. A mitigation strategy is the oxidation of methane to carbon dioxide, which is approximately twenty-one times less effective at global warming than methane on a mass-basis. The low non-combustible methane concentrations at high MVA flow rates call for a catalytic strategy of oxidation. A laboratory-scale coal-packed biofilter was designed and partially removed methane from humidified air at flow rates between 0.2 and 2.4 L min−1 at 30°C with nutrient solution added every three days. Methane oxidation was catalysed by a complex community of naturally-occurring microorganisms, with the most abundant member being identified by 16S rRNA gene sequence as belonging to the methanotrophic genus Methylocystis. Additional inoculation with a laboratory-grown culture of Methylosinus sporium, as investigated in a parallel run, only enhanced methane consumption during the initial 12 weeks. The greatest level of methane removal of 27.2±0.66 g methane m−3 empty bed h−1 was attained for the non-inoculated system, which was equivalent to removing 19.7±2.9% methane from an inlet concentration of 1% v/v at an inlet gas flow rate of 1.6 L min−1 (2.4 min empty bed residence time). These results show that low-cost coal packing holds promising potential as a suitable growth surface and contains methanotrophic microorganisms for the catalytic oxidative removal of methane. PMID:24743729

PENGOLAHAN AIR LINDI DENGAN PROSES KOMBINASI BIOFILTER ANAEROB-AEROB DAN WETLAND

Directory of Open Access Journals (Sweden)

Mochtar Hadiwidodo

2012-09-01

Full Text Available In Indonesia leachate is still an issue yet to be addressed. With a high content of pollutant parameters and lack of government support resulting landfill must think about the appropriate treatment to be safe for treating waste when discarded into the environment. Biofilter methods and wetland is the one of alternatives leachate treatment that can be used. This method does not require a large operating costs and does not require skilled professionals to operate it. With a combination of wetland and biofilter, it is expected to reduce the content of pollutants in the leachate, so it can be meet the wastewater quality standards which set by the government. The levels of pollutants were tested in this study is the BOD5, COD, TSS, ammonia, nitrite and nitrate

Anaerobe-Aerobe Submerged Biofilter Technology for Domestic Waste Water Treatment

International Nuclear Information System (INIS)

Nusa-Idaman-Said

2000-01-01

Water pollution in the big cities in Indonesia, especially in DKI Jakarta has shown serious problems. One of the potential sources of water pollution is domestic wastewater that is wastewater from kitchens, laundry, bathing and toilets. These problems have become more serious since the spreads of sewerage systems are still low, so that domestic, institutional and commercial wastewater cause severe water pollution in many rivers or shallow ground water. Bases on the fact that the progress of development of sewerage system is still low, it is important to develop low cost technology for individual house hold or semi communal wastewater treatment such as using anaerobic and aerobic submerged biofilter. This paper describes alternative technology for treatment of household wastewater or organic wastewater using anaerobic and aerobic submerged biofilter. Using this technology can decrease BOD, COD and Suspended Solids (SS) concentration more than 90 %. (author)

A Comparative Study of Physical and Chemical Processes for Removal of Biomass in Biofilters

Directory of Open Access Journals (Sweden)

Jorge Alberto Mendoza-Pérez

2011-08-01

Full Text Available After 6 months of operation a long-term biofilter was stopped for two weeks and then it was started up again for a second experimental period of almost 1.3 years, with high toluene loads and submitted to several physical and chemical treatments in order to remove excess biomass that could affect the reactor’s performance due to clogging, whose main effect is a high pressure drop. Elimination capacity and removal efficiency were determined after each treatment. The methods applied were: filling with water and draining, backwashing, and air sparging. Different flows and temperatures (20, 30, 45 and 60 °C were applied, either with distilled water or with different chemicals in aqueous solutions. Treatments with chemicals caused a decrease of the biofilter performance, requiring periods of 1 to 2 weeks to recover previous values. The results indicate that air sparging with pure distilled water as well as with solutions of NaOH (0.01% w/v and NaOCl (0.01% w/v were the treatments that removed more biomass, working either at 20, 30 or 45 °C and at relatively low flow rates (below 320 L h−1, but with a high biodegradation inhibition after the treatments. Dry biomass (g VS content was determined at three different heights of the biofilter in order to carry out each experiment under the same conditions. The same amount of dry biomass when applying a treatment was established so it could be considered that the biofilm conditions were identical. Wet biomass was used as a control of the biofilter’s water content during treatments. Several batch assays were performed to support and quantify the observed inhibitory effects of the different chemicals and temperatures applied.

Elimination of butanal from odorous air by a labscale biofilter

NARCIS (Netherlands)

Weckhuysen, B.M.; Vriens, L.; Verachtert, H.

1991-01-01

Butanal was chosen as a model compound for testing the performance of biofilters. It's a member of an important class of odour compounds released by waste water treatment plants of animal rendering and food processing industry. The influence of nutrient supplementation has been investigated using

Inside Story of Gas Processes within Stormwater Biofilters: Does Greenhouse Gas Production Tarnish the Benefits of Nitrogen Removal?

Science.gov (United States)

Payne, Emily G I; Pham, Tracey; Cook, Perran L M; Deletic, Ana; Hatt, Belinda E; Fletcher, Tim D

2017-04-04

Stormwater biofilters are dynamic environments, supporting diverse processes that act to capture and transform incoming pollutants. However, beneficial water treatment processes can be accompanied by undesirable greenhouse gas production. This study investigated the potential for nitrous oxide (N 2 O) and methane (CH 4 ) generation in dissolved form at the base of laboratory-scale stormwater biofilter columns. The influence of plant presence, species, inflow frequency, and inclusion of a saturated zone and carbon source were studied. Free-draining biofilters remained aerobic with negligible greenhouse gas production during storm events. Designs with a saturated zone were oxygenated at their base by incoming stormwater before anaerobic conditions rapidly re-established, although extended dry periods allowed the reintroduction of oxygen by evapotranspiration. Production of CH 4 and N 2 O in the saturated zone varied significantly in response to plant presence, species, and wetting and drying. Concentrations of N 2 O typically peaked rapidly following stormwater inundation, associated with limited plant root systems and poorer nitrogen removal from biofilter effluent. Production of CH 4 also commenced quickly but continued throughout the anaerobic interevent period and lacked clear relationships with plant characteristics or nitrogen removal performance. Dissolved greenhouse gas concentrations were highly variable, but peak concentrations of N 2 O accounted for nitrogen load. While further work is required to measure surface emissions, the potential for substantial release of N 2 O or CH 4 in biofilter effluent appears relatively low.

Effect of bed particles to combustion of gases in fluidized bed

Energy Technology Data Exchange (ETDEWEB)

Raiko, R.; Wallen, V.; Etelaeaho, R.; Correia, S. [Tampere Univ. of Technology (Finland). Energy and Process Engineering

1997-10-01

The objective of this project was to obtain experimental data on effects of sand particles to the combustion of gases. The effect of the surface area of the particles was tested using different sized particles. The fluidized bed reactor used in these experiments was a stainless-steel tube with an internal diameter of 42 mm surrounded by an electric heater. The test rig was built in the Laboratory of Energy and Process Engineering at Tampere University of Technology. In order to elucidate the possible changes of particle surface, microscopic and porosimetric studies were conducted with both fresh bed particles and used bed particles. These measurements indicate that carbon monoxide significantly reacts with oxygen in the particulate or emulsion phase of a fluidized bed, if the residence time is long enough. The reaction rate depends mainly on temperature, air coefficient, residence time and particle size of the solids. It seems that the combustion enhances if the average particle size increases. Whether this is caused by increased free path length or reduced specific surface area of the bed is yet unknown. The first might be more probable cause because the majority of reactions often took place in the freeboard right above the bed. It was clear that the bed hindered proper combustion in several cases. (orig.)

Dynamic olfactometry and GC–TOFMS to monitor the efficiency of an industrial biofilter

Energy Technology Data Exchange (ETDEWEB)

Gutiérrez, M.C.; Martín, M.A. [University of Cordoba, Department of Inorganic Chemical and Chemical Engineering, Campus Universitario de Rabanales, Carretera N-IV, km 396, Edificio Marie Curie, 14071 Córdoba (Spain); Pagans, E.; Vera, L. [Odournet SL, Parc de Recerca UAB, Edificio Eureka, Espacio P2M2, 08193, Bellaterra, Cerdanyola del Vallès, Barcelona (Spain); García-Olmo, J. [NIR/MIR Spectroscopy Unit, Central Service for Research Support (SCAI), University of Cordoba, Campus de Rabanales, 14071 Cordoba (Spain); Chica, A.F., E-mail: afchica@uco.es [University of Cordoba, Department of Inorganic Chemical and Chemical Engineering, Campus Universitario de Rabanales, Carretera N-IV, km 396, Edificio Marie Curie, 14071 Córdoba (Spain)

2015-04-15

Biofiltration is the most widely used technique for eliminating odours in waste treatment plants. Volatile organic compounds (VOCs) are among the odorous compounds emitted by waste management plants, and serve as variables to measure odour emissions depending on the type of aeration process used. In this work, we assess the performance of an industrial-scale biofilter where composting is the main source of VOCs and odour emissions. Dynamic olfactometry is the sensorial technique used to determine odour concentration, while gas chromatography–time of flight-mass spectrometry (GC–TOFMS) is used to perform the chemical characterization. This work examines a total of 82 compounds belonging to 15 odorous families of VOCs, particularly mercaptans, sulphur-containing compounds, alcohols and terpenes, among others. Principal component analysis (PCA) is used to assess the influence of each of these families of VOCs on the total variance of the measure with regard to both the input and output flow of the biofilter. Finally, partial least-squares (PLS) regression is used to estimate the odour concentration in each of the samples taken at the inlet and outlet of the biofilter in each of the samples based on the chemical information provided by chromatographic analysis. The study shows that there is an adequate correlation (r = 0.9751) between real and estimated odour concentrations, both of which are expressed in European odour units per cubic metre (ou{sub E}·m{sup −3}). - Highlights: • Odour and VOC removal by industrial biofilter was evaluated. • Dynamic olfactometry and GC-TOF MS were the techniques used. • The compost aeration mode was considered in this study. • The influence of 15 VOC families on sample variance was demonstrated by PCA. • Odour concentration was predicted from selected chromatographic information by PLS.

Long-term operational studies of lab-scale pumice-woodchip packed stormwater biofilters.

Science.gov (United States)

Cheng, Jing; Yuan, Qingke; Kim, Youngchul

2017-06-13

The performance of three pumice-woodchip packed stormwater biofilter (PWSWBF) systems with three packing volume ratios of pumice to woodchip (1:2, 1:1 and 2:1) were compared. The results show that the PWSWBF system packed with a lower percentage of woodchip attained a higher removal efficiency of TCOD, TN, NH 4 -N and TP, whereas all three systems completely removed nitrate. The highest removal efficiencies for TCOD, TN, NH 4 -N, NO 3 -N and TP were 95%, 70%, 86%, 100% and 100%, respectively. In the biofilter with a lower percentage of woodchip, the pollutants that get removed through aerobic biological processes were removed more significantly, which is attributed to less oxygen depletion via woodchip decomposition, which is common under wet conditions. Nitrate was significantly removed via denitrification in all three systems, indicating that the woodchip that occupied one-third of the main media was sufficient for denitrification, and also that the oxygen condition inside the column was proper for denitrification to proceed. A smaller amount of woodchip as the packing material also mitigated the adverse effect of the release of organics from the media during the initial period. In addition, the system showed very good buffering capacity, in that the outflow pH was constant within the optimal range for microorganism growth.

Effect of bed configuration on pebble flow uniformity and stagnation in the pebble bed reactor

International Nuclear Information System (INIS)

Gui, Nan; Yang, Xingtuan; Tu, Jiyuan; Jiang, Shengyao

2014-01-01

Highlights: • Pebble flow uniformity and stagnation characteristics are very important for HTR-PM. • Arc- and brachistochrone-shaped configuration effects are studied by DEM simulation. • Best bed configurations with uniform flow and no stagnated pebbles are suggested. • Detailed quantified characteristics of bed configuration effects are shown for explanation. - Abstract: Pebble flow uniformity and stagnation characteristics are very important for the design of pebble bed high temperature gas-cooled reactor. Pebble flows inside some specifically designed contraction configurations of pebble bed are studied by discrete element method. The results show the characteristics of stagnation rates, recycling rates, radial distribution of pebble velocity and residence time. It is demonstrated clearly that the bed with a brachistochrone-shaped configuration achieves optimum levels of flow uniformity and recycling rate concentration, and almost no pebbles are stagnated in the bed. Moreover, the optimum choice among the arc-shaped bed configurations is demonstrated too. Detailed information shows the quantified characteristics of bed configuration effects on flow uniformity. In addition, a good design of the pebble bed configuration is suggested

Impact of water boundary layer diffusion on the nitrification rate of submerged biofilter elements from a recirculating aquaculture system

DEFF Research Database (Denmark)

Prehn, Jonas; Waul, Christopher Kevin; Pedersen, Lars-Flemming

2012-01-01

Total ammonia nitrogen (TAN) removal by microbial nitrification is an essential process in recirculating aquaculture systems (RAS). In order to protect the aquatic environment and fish health, it is important to be able to predict the nitrification rates in RAS’s. The aim of this study was to det...... biofilters. The results may thus have practical implications in relation to the design, operational strategy of RAS biofilters and how to optimize TAN removal in fixed film biofilter systems......Total ammonia nitrogen (TAN) removal by microbial nitrification is an essential process in recirculating aquaculture systems (RAS). In order to protect the aquatic environment and fish health, it is important to be able to predict the nitrification rates in RAS’s. The aim of this study...

Nitrogen waste from rainbow trout (Oncorhynchus mykiss) with particular focus on urea

DEFF Research Database (Denmark)

Dalsgaard, Anne Johanne Tang; Larsen, Bodil Katrine; Pedersen, Per Bovbjerg

2015-01-01

a laboratory, mass-balance approach, the current study examined the effects of commercially applied feeding levels on the loading of different N waste forms, including daily fluctuations in dissolved total nitrogen (TN), total ammonia nitrogen (TAN), urea-N, and non-characterized, dissolved N deriving from...... juvenile rainbow trout (Oncorhynchus mykiss). In addition, the study examined whether there was a removal of urea-N across a moving bed biofilter operated as end-of-pipe under commercial conditions. The laboratory, mass-balance study showed that there were no effects of feeding levels (1.3, 1.5 or 1....../nitrogen. Results from the commercially operated, nitrifying biofilter showed that urea-N was removed at a rate of 0.014 g N m2 day−1. Compared to the removal of TAN (0.208 g N m2 day−1), the moving bed biofilter was 1.07 times more active in removing dissolved N than immediately expected when only considering TAN...

Determination of the efficiency of sawdust and coco fiber used as Biofilter for pollutant removal for the treatment of wastewater

Directory of Open Access Journals (Sweden)

Jimmy Vicente Reyes

2016-09-01

Full Text Available Water is a resource used by mankind for industrial and domestic needs, which once used, is discharged into the public sewer system or septic tanks. This project proposes an ecological alternative for the treatment of wastewater from domestic use named Biofilter, which is built of living material (worms and inert material (chip and gravel, which filters the wastewater; the biological filter has shown high efficiency in the removal of organic matter and pathogens. The field work was carried out with experimental biological filters, to ascertain the best composition of inert material, different variants were used. Two experimental Biofilters, one using sawdust and the other coco fiber were used in the treatment of domestic wastewater; treated samples from each reactor were subjected to laboratory analysis. The analysis and interpretation of results showed that the Biofilter using sawdust removed 53.53 % of pollutants and is outside the required norm for wastewater treatment and the Biofilter using coco fiber removed 82.37 % of contaminants and is within the Environmental Quality Norm and Effluent Discharge: Water Resource.

Respirometric oxygen demand determinations of laboratory- and field-scale biofilters

International Nuclear Information System (INIS)

Rho, D.; Mercier, P.; Jette, J.F.

1995-01-01

A biofiltration experiment operated at three inlet concentrations (425, 830, and 1,450 mg m -3 ), showed that the specific oxygen consumption rate was highly correlated (R = 0.938, n = 23) with the toluene elimination capacity. A radiorespirometric test was found to be more sensitive and appropriate for the field-scale biofilter treating gasoline vapors

Petroleum environmental research forum field study on biofilters for control of volatile hydrocarbons

International Nuclear Information System (INIS)

Leson, G.; Smith, B.J.

1997-01-01

A field study on the treatment of volatile petroleum hydrocarbons (PHC) by biofiltration was conducted by the Petroleum Environmental Research Forum (PERF) between 1992 and 1994. Its objective was to assess the technical, regulatory, and economic feasibility of biofiltration for off-gases from petroleum processing and soil remediation equipment. It involved three small-scale biofilters provided by US vendors, treating off-gas from two soil vapor extraction sites and a source of refinery wastewater. Comprehensive monitoring of biofilter operating parameters and performance was conducted. Typically more than 95% of aromatic compounds such as benzene, and odorous reduced sulfur compounds can be removed at residence times of one minute or less, while removal of more than 70% of light aliphatics will require residence times of several minutes, and will thus require correspondingly large filter volumes and higher capital expenditure. The high percentage removal of aromatic hazardous air pollutants (HAP) and odors can generally be accomplished at comparatively short residence times while the need for high-percentage removal, particular of light aliphatics ( 5 ) will generally render biofiltration noncompetitive. Finally, a preliminary economic comparison of biofilters and established control technologies suggested that biofiltration may, for a representative design case involving off-gas from a refinery wastewater treatment operation, offer considerable savings in total cost of air pollution control for petroleum hydrocarbon streams if regulations require the control of aromatic HAP or odors

Development of constructed wetland using hydroponic biofilter method for purification of hyper-eutrophic lake water; Fueiyoka kosui no joka no tameno suiko seibutsu rokaho wo mochiita jinko shicchi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Aizaki, M. [Shimane Univ., Matsue (Japan)] Nakasato, H. [Top Ecology Co. Ltd., Tokyo (Japan)

1997-09-10

Applying the hydroponic biofilter method as a direct purification method for a hyper-eutrophic lake water, an experiment was carried out at the Tsuchiura Port on Lake Kasumigaura to obtain data for constructing a hydrophilic artificial wetland. Purification of hyper-eutrophic lake water containing a large amount of water blooms in summer was attempted applying the hydroponic biofilter method for which hydrophyte is used. As a result, it was clarified, by applying the hydroponic biofilter method, that capturing effect of suspended substances can be achieved in the rooting zone, captured suspended substances are decomposed at high rate, and the revolved nutrient salt can be absorbed and assimilated by the use of plants having high growth rates. Ipomoea aquatica had the highest removal activity, followed by nasturtium officinal, menthe spicata, and oenanthe javanica. As a result, it became clear that a constructed wetland made with the hydroponic biofilter method can be applied as a direct purifying method for hyper-eutrophic lake water by selecting appropriate plants in accordance with season. 18 refs., 1 fig., 4 tabs.

Bed diameter effects and incipient slugging in gas fluidized beds

International Nuclear Information System (INIS)

Agarwal, P.K.

1986-01-01

The coalescence and growth of bubble swarms formed at the distributor of a fluidized bed gives rise to lateral as well as vertical distributions of bubble properties. However, existing models employ average bubble properties obtained largely from semi-empirical considerations. In a recent Paper, the author developed a bubble growth model based on a population balance approach. Analytical expressions were derived for the bubble characteristic distributions and averages. However, the model, developed for unconstrained growth, did not take into account the effect of the bed diameter and the possibility of slugging. In this Paper, the model is extended to take these aspects into account. A slugging criterion is also developed which is expected to be valid for the regime where incipient slugging depends on the bed height as well as the region where bed height does not significantly affect minimum slugging conditions

Macrokinetic determination of isopropanol removal using a downward flow biofilter

Directory of Open Access Journals (Sweden)

Vissanu Meeyoo

2004-02-01

Full Text Available Biofiltration is a process for eliminating contaminants in air using microorganisms immobilized on a surface of solid support media. This technique has been used successfully to control a number of air contaminants such as odors, Volatile Organic Compounds (VOCs, and Hazardous Air Pollutants (HAPs due to its economic attraction.Microorganisms obtained from local activated sludge (Huay-Kwang wastewater treatment plant (Bangkok, Thailand were selectively enriched and inoculated to the biofilter. The downward flow biofilterwas chosen, due to the ease of water compensation at the dry zone, to operate continuously for more than 3 months under various concentrations of isopropanol alcohol (IPA input at a constant filtered air flow rate of 3 L/min. The maximum IPA elimination capacity of 276 g/m3-h was achieved at the IPA inlet of 342 g/m3-h with acetone production rate of 56 g/m3-h as the intermediate. It was also found that the acetone vapour was partly degraded by the acetone-utilizing microorganisms before leaving the bed. In order to understand the transport phenomena of biofiltration, it is necessary to consider the kinetic behavior of the bioreaction. Therefore, this paper introduces Wani’s method of macrokinetic determination based on the simple Monod kinetic (Wani, Lau and Branion, 1999. In this study, the maximum reaction rate per unit volume (Rm and the Monod constant (KM were found to be 0.12 g/m3 -s and 2.72 g/m3 respectively.

Which species? A decision-support tool to guide plant selection in stormwater biofilters

Science.gov (United States)

Payne, Emily G. I.; Pham, Tracey; Deletic, Ana; Hatt, Belinda E.; Cook, Perran L. M.; Fletcher, Tim D.

2018-03-01

Plant species are diverse in form, function and environmental response. This provides enormous potential for designing nature-based stormwater treatment technologies, such as biofiltration systems. However, species can vary dramatically in their pollutant-removal performance, particularly for nitrogen removal. Currently, there is a lack of information on how to efficiently select from the vast palette of species. This study aimed to identify plant traits beneficial to performance and create a decision-support tool to screen species for further testing. A laboratory experiment using 220 biofilter columns paired plant morphological characteristics with nitrogen removal and water loss for 20 Australian native species and two lawn grasses. Testing was undertaken during wet and dry conditions, for two biofilter designs (saturated zone and free-draining). An extensive root system and high total biomass were critical to the effective removal of total nitrogen (TN) and nitrate (NO3-), driven by high nitrogen assimilation. The same characteristics were key to performance under dry conditions, and were associated with high water use for Australian native plants; linking assimilation and transpiration. The decision-support tool uses these scientific relationships and readily-available information to identify the morphology, natural distribution and stress tolerances likely to be good predictors of plant nitrogen and water uptake.

Application of two-stage biofilter system for the removal of odorous compounds.

Science.gov (United States)

Jeong, Gwi-Taek; Park, Don-Hee; Lee, Gwang-Yeon; Cha, Jin-Myeong

2006-01-01

Biofiltration is a biological process which is considered to be one of the more successful examples of biotechnological applications to environmental engineering, and is most commonly used in the removal of odoriferous compounds. In this study, we have attempted to assess the efficiency with which both single and complex odoriferous compounds could be removed, using one- or two-stage biofiltration systems. The tested single odor gases, limonene, alpha-pinene, and iso-butyl alcohol, were separately evaluated in the biofilters. Both limonene and alpha-pinene were removed by 90% or more EC (elimination capacity), 364 g/m3/h and 321 g/m3/h, respectively, at an input concentration of 50 ppm and a retention time of 30 s. The iso-butyl alcohol was maintained with an effective removal yield of more than 90% (EC 375 g/m3/h) at an input concentration of 100 ppm. The complex gas removal scheme was applied with a 200 ppm inlet concentration of ethanol, 70 ppm of acetaldehyde, and 70 ppm of toluene with residence time of 45 s in a one- or two-stage biofiltration system. The removal yield of toluene was determined to be lower than that of the other gases in the one-stage biofilter. Otherwise, the complex gases were sufficiently eliminated by the two-stage biofiltration system.

Biopiles and biofilters combined for soil cleanup

International Nuclear Information System (INIS)

Lei, J.; Sansregret, J.L.; Cyr, B.

1994-01-01

Bioremediation of hydrocarbon-contaminated soils can be completed using a combination of biopile and biofiltration technologies. Target contaminants, such as gasoline, jet fuel, diesel fuel and other petroleum-derived products are removed from the soil by biodegradation and volatilization in the biopile. Air emissions from the biopile containing volatile hydrocarbons are treated subsequently in a biofilter, where the pollutants are degraded and mineralized by heterotrophic aerobic microorganisms. In the biopile process, contaminated soil is excavated and stockpiled in a treatment area. Remediation of the soil relies on microbial degradation and volatilization of hydrocarbons under controlled treatment conditions

Technological and life cycle assessment of organics processing odour control technologies

Energy Technology Data Exchange (ETDEWEB)

Bindra, Navin [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Dubey, Brajesh, E-mail: bkdubey@civil.iitkgp.ernet.in [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Environmental Engineering Division, Department of Civil Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Dutta, Animesh [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada)

2015-09-15

As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. - Highlights: • Assessment of odour control technologies for organics processing facilities. • Comparative life cycle assessment of three odour control technologies was conducted

Effects of bed-load movement on flow resistance over bed forms

Indian Academy of Sciences (India)

Abstract. The effect of bed-load transport on flow resistance of alluvial channels with undulated bed was experimentally investigated. The experiments were carried out in a tilting flume 250mm wide and 12·5m long with glass-sides of rectan- gular cross-section and artificial dune shaped floor that was made from Plexi-glass.

Styrene removal from wate gas by the fungus Exophiala Jeanselmei in a biofilter

NARCIS (Netherlands)

Cox, Hubertus Henricus Jacobus

1995-01-01

Styrene is an environmental pollutant, emitted in large quantities to the atmosphere by various industrial sectors. Legislation requires industry to reduce the emission of styrene. One option to purify industrial waste gases is biological treatment in biofilters. ... Zie: Summary

The effect of bed non-uniformities and porosity of particles on dryout in boiling particle beds

International Nuclear Information System (INIS)

Macbeth, R.V.; Mogford, D.J.; Willshire, S.J.

1988-03-01

This report relates to an on-going experimental programme concerned with the coolability of beds of reactor core debris or rubble immersed in a liquid coolant, as might occur in an accident situation. The objectives are to develop experimental techniques, improve the understanding of bed cooling mechanisms, determine dry-out limitations of various bed configurations and particle shapes and sizes and devise ways of improving bed coolability. The report concentrates on a recently discovered effect on bed coolability of particle porosity, such as exists in fragmented UO 2 fuel pellets. It is shown that porosity can lower bed dry-out powers by a factor of 4 or 5. A mechanism which explains the effect is presented. The report also gives results of bed non-uniformities obtained by mixing glass particles with the dielectrically heated 'ferrite' particles used in the experiments. (author)

Biological treatment of H(2)S using pellet activated carbon as a carrier of microorganisms in a biofilter.

Science.gov (United States)

Duan, Huiqi; Koe, Lawrence C C; Yan, Rong; Chen, Xiaoge

2006-08-01

Biological treatment is an emerging technology for treating off-gases from wastewater treatment plants. The most commonly reported odourous compound in off-gases is hydrogen sulfide (H(2)S), which has a very low odor threshold. This study aims to evaluate the feasibility of using a biological activated carbon as a novel packing material, to achieve a performance-enhanced biofiltration processes in treating H(2)S through an optimum balance and combination of the adsorption capacity with the biodegradation of H(2)S by the bacteria immobilized on the material. The biofilm was mostly developed through culturing the bacteria in the presence of carbon pellets in mineral media. Scanning electron microscopy (SEM) was used to identify the biofilm development on carbon surface. Two identical laboratory scale biofilters, one was operated with biological activated carbon (BAC) and another with virgin carbon without bacteria immobilization. Various concentrations of H(2)S (up to 125 ppmv) were used to determine the optimum column performance. A rapid startup (a few days) was observed for H(2)S removal in the biofilter. At a volumetric loading of 1600 m(3)m(-3)h(-1) (at 87 ppmv H(2)S inlet concentration), elimination capacity of the BAC (181 gH(2)Sm(-3)h(-1)) at removal efficiency (RE) of 94% was achieved. If the inlet concentration was kept at below 30 ppmv, high H(2)S removal (over 99%) was achieved at a gas retention time (GRT) as low as 2s, a value, which is shorter than most previously reported for biofilter operations. The bacteria population in the acidic biofilter demonstrated capacity for removal of H(2)S in a broad pH range (pH 1-7). There are experimental evidences showing that the spent BAC could be re-used as packing material in a biofilter based on BAC. Overall, the results indicated that an unprecedented performance could be achieved by using BAC as the supporting media for H(2)S biofiltration.

Biofilters for stormwater harvesting: understanding the treatment performance of key metals that pose a risk for water use.

Science.gov (United States)

Feng, Wenjun; Hatt, Belinda E; McCarthy, David T; Fletcher, Tim D; Deletic, Ana

2012-05-01

A large-scale stormwater biofilter column study was conducted to evaluate the impact of design configurations and operating conditions on metal removal for stormwater harvesting and protection of aquatic ecosystems. The following factors were tested over 8 months of operation: vegetation selection (plant species), filter media type, filter media depth, inflow volume (loading rate), and inflow pollutant concentrations. Operational time was also integrated to evaluate treatment performance over time. Vegetation and filter type were found to be significant factors for treatment of metals. A larger filter media depth resulted in increased outflow concentrations of iron, aluminum, chromium, zinc, and lead, likely due to leaching and mobilization of metals within the media. Treatment of all metals except aluminum and iron was generally satisfactory with respect to drinking water quality standards, while all metals met standards for irrigation. However, it was shown that biofilters could be optimized for removal of iron to meet the required drinking water standards. Biofilters were generally shown to be resilient to variations in operating conditions and demonstrated satisfactory removal of metals for stormwater-harvesting purposes. © 2012 American Chemical Society

Performance of double-layer biofilter packed with coal fly ash ceramic granules in treating highly polluted river water.

Science.gov (United States)

Jing, Zhaoqian; Li, Yu-You; Cao, Shiwei; Liu, Yuyu

2012-09-01

To improve trickling filters' denitrification efficiency, a biofilter with a trickling upper layer and a submerged lower layer was developed and applied in treating highly polluted river water. It was packed with porous coal fly ash ceramic granules. Its start-up characteristics, influence of hydraulic loading rates (HLR), carbon/nitrogen (C/N) ratio and filter depth on pollutants removal were investigated. The results indicated this biofilter was started quickly in 16 days with river sediment as inoculum. Alternating nitrification and denitrification were achieved when water flowed downwards. COD and nitrogen were mainly removed in the upper layer and the lower layer, respectively. With HLR of 4.0-5.0m(3)/(m(2)d), chemical oxygen demand (COD), ammonium (NH(4)(+)-N) and total nitrogen (TN) in the effluent were below 50, 5 and 15 mg/L, respectively. This biofilter removed more than 80% of COD, 85% of NH(4)(+)-N and 60% of TN with C/N ratios ranging from 6 to 10. Copyright © 2012 Elsevier Ltd. All rights reserved.

Microbial Biotreatment of Actual Textile Wastewater in a Continuous Sequential Rice Husk Biofilter and the Microbial Community Involved

OpenAIRE

Forss, J?rgen; Lindh, Markus V.; Pinhassi, Jarone; Welander, Ulrika

2017-01-01

Textile dying processes often pollute wastewater with recalcitrant azo and anthraquinone dyes. Yet, there is little development of effective and affordable degradation systems for textile wastewater applicable in countries where water technologies remain poor. We determined biodegradation of actual textile wastewater in biofilters containing rice husks by spectrophotometry and liquid chromatography mass spectrometry. The indigenous microflora from the rice husks consistently performed >90% de...

The effect of vibration on bed voidage behaviors in fluidized beds with large particles

Directory of Open Access Journals (Sweden)

H. Jin

2007-09-01

Full Text Available The effects of vibration parameters, operating conditions and material properties on bed voidage were investigated using an optical fiber probe approach in a vibrating fluidized bed with a diameter of 148 mm. Variables studied included frequency (0-282 s-1, amplitude (0 mm-1 mm, bed height (0.1 m-0.4 m as well as four kinds of particles (belonging to Geldart's B and D groups. The axial and radial voidage distribution with vibration is compared with that without vibration, which shows vibration can aid in the fluidization behaviors of particles. For a larger vibration amplitude, the vibration seriously affects bed voidage. The vibration energy can damp out for particle layers with increasing the bed height. According to analysis of experimental data, an empirical correlation for predicting bed voidage, giving good agreement with the experimental data and a deviation within ±15%, was proposed.

Structure of the bacterial community in a biofilter during dimethyl sulfide (DMS) removal processes.

Science.gov (United States)

Chung, Ying-Chien; Cheng, Chiu-Yu; Chen, Tzu-Yu; Hsu, Jo-Shan; Kui, Chun-Chi

2010-09-01

We report here both the successful treatment of DMS in a biofilter and the dynamic changes that occur in the composition of the bacterial community of the biofilter during this process. Denaturing gradient gel electrophoresis of eubacterial 16S rDNA samples taken from packing material at different DMS removal stages revealed 11 distinct bands. Phylogenetic analysis showed that the sequences of these bands were closest to sequences of species of the Proteobacteria, Firmicutes, and Actinobacteria. The specific occurrence of these bacterial species varied mainly with DMS load, but it was also affected by the addition of glucose and by ambient temperature. Based on the characteristics of the identified species, the system is conducive for such processes as sulfur oxidation, sulfate reduction, carbon oxidation, and fermentation. The strains identified in this study are potential candidates for purifying waste gas effluents containing DMS gas. Copyright 2010 Elsevier Ltd. All rights reserved.

Mass transfer dynamics of ammonia in high rate biomethanation of poultry litter leachate.

Science.gov (United States)

Gangagni Rao, A; Gandu, Bharath; Swamy, Y V

2012-04-01

In the present study possibility of coupling biofilter to arrest ammonia (NH(3)) emission to the atmosphere from the integrated UASB and stripper (UASB+ST) system treating poultry litter leachate was studied. UASB+ST with biofilter (UASB+ST+BF) exhibited removal efficiency (RE) of NH(3) in the range of 98-99% (below 28 ppmV (parts per million by volume)) with low cost agricultural residue as a bedding material. Mass transfer dynamics of TAN in the system revealed that TAN loss to atmosphere was below 1% in UASB+ST+BF where as it was in the range of 70-90% in UASB+ST. Cost estimates revealed that financial implications due to the addition of biofilter were below 10% of total capital cost. TAN retained in the bedding material of biofilter could also be utilized as soil conditioner upon saturation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Biofilter media gas pressure loss as related to media particle size and particle shape

DEFF Research Database (Denmark)

Pugliese, Lorenzo; Poulsen, Tjalfe G.; Røjgaard Andreasen, Rune

2013-01-01

Pressure loss (ΔP) is a key parameter for estimating biofilter energy consumption. Accurate predictions of ΔP as a function of air velocity (V) are therefore essential, to assess energy consumption and minimize operation costs. This paper investigates the combined impact of medium particle size...

The use of oak chips and coconut fiber as biofilter media to remove vocs in rendering process.

Science.gov (United States)

Tymczyna, Leszek; Chmielowiec-Korzeniowska, Anna; Paluszak, Zbigniew; Dobrowolska, Magadalena; Banach, Marcin; Pulit, Jolanta

2013-01-01

The study evaluated the effectiveness of air biofiltration in rendering plants. The biofilter material comprised compost soil (40%) and peat (40%) mixed up with coconut fiber (medium A) and oak bark (medium B). During biofiltration average VOCs reduction reached 88.4% for medium A and 89.7% for medium B. A positive relationship of aldehyde reduction from material humidity (r = 0.502; α<0.05) was also noted. Other biomaterial parameters did not affect the treatment efficiency.

Theory and measurements of electrophoretic effects in monolith, fixed-bed, and fluidized-bed plasma reactors

International Nuclear Information System (INIS)

Morin, T.J.

1989-01-01

Pressure gradients and secondary flow fields generated by the passage of electrical current in a d.c. gas discharge or gas laser are topics of longstanding interest in the gaseous electronics literature. These hydrodynamic effects of space charge fields and charged particle density gradients have been principally exploited in the development of gas separation and purification processes. In recent characterization studies of fixed-bed and fluidized-bed plasma reactors several anomalous flow features have been observed. These reactors involve the contacting of a high-frequency, resonantly-sustained, disperse gas discharge with granular solids in a fixed or fluidized bed. Anomalies in the measured pressure drops and fluidization velocities have motivated the development of an appropriate theoretical approach to, and some additional experimental investigations of electrophoretic effects in disperse gas discharges. In this paper, a theory which includes the effects of space charge and diffusion is used to estimate the electric field and charged particle density profiles. These profiles are then used to calculate velocity fields and gas flow rates for monolith, fixed-bed, and fluidized-bed reactors. These results are used to rationalize measurements of gas flow rates and axial pressure gradients in high-frequency disperse gas discharges with and without an additional d.c. axial electric field

Efficacy of a novel biofilter in hatchery sanitation: II. Removal of odorogenous pollutants.

Science.gov (United States)

Tymczyna, Leszek; Chmielowiec-Korzeniowska, Anna; Drabik, Agata; Skórska, Czesława; Sitkowska, Jolanta; Cholewa, Grazyna; Dutkiewicz, Jacek

2007-01-01

The present research assessed the treatment efficiency of odorogenous pollutants in air from a hatchery hall vented on organic and organic-mineral beds of an enclosed-container biofilter. In this study, the following media were used: organic medium containing compost and peat (OM); organic-mineral medium containing bentonite, compost and peat (BM); organic-mineral medium containing halloysite, compost and peat (HM). The concentration of odorogenous gaseous pollutants (sulfur compounds and amines) in the hatching room air and in the air after biotreatment were determined by gas chromatography. In the hatchery hall among the typical odorogenous pollutants, there were determined 2 amines: 2-butanamine and 2-pentanamine, hydrogen sulfide, sulfur dioxide, carbon disulfide, sulfides and mercaptans. Ethyl mercaptan showed the highest levels as its mean concentration in the hatchery hall air exceeded 60 microg/m3 and in single samples even 800 microg/m3. A mean concentration of 2-butanamine and sulfur dioxide in the examined air also appeared to be relatively high--21.405 microg/m3 and 15.279 microg/m3, respectively. In each filter material, the air treatment process ran in a different mode. As the comparison reveals, the mean reduction of odorogenous contaminants recorded in the hall and subjected to biotreatment was satisfying as it surpassed 60% for most established pollutants. These high removal values were confirmed statistically only for single compounds. However, a low removal level was reported for hydrogen sulfide and sulfur dioxide. No reduction was recorded in the bentonite supplemented medium (BM) for sulfur dioxide and methyl mercaptan. In the organic medium (OM) no concentration fall was noted for dipropyl sulfide either. In all the media investigated, the highest removal rate (100%), not confirmed statistically, was observed for carbon disulfide. Very good results were obtained in the medium with a bentonite additive (BM) for both identified amines, whose

1 The Effect of Camber Bed Drainage

African Journals Online (AJOL)

User

The Effect of Camber Bed Drainage Landforms on Soil. Nutrient Distribution and Grain Yield of Maize on the Vertisols ... The Vertisols of the Accra Plains of Ghana are water logged after significant rainfall ... Excess application of 15-15-15 NPK and sulphate of ammonia fertilizers (150% .... beds, before planting and nutrient.

Improved lignin pyrolysis for phenolics production in a bubbling bed reactor--Effect of bed materials.

Science.gov (United States)

Li, Dongbing; Briens, Cedric; Berruti, Franco

2015-01-01

Lignin pyrolysis was studied in a bubbling fluidized bed reactor equipped with a fractional condensation train, using nitrogen as the fluidization gas. The effect of different bed materials (silica sand, lignin char, activated lignin char, birch bark char, and foamed glass beads) on bio-oil yield and quality was investigated for a pyrolysis temperature of 550 °C. Results how that a bed of activated lignin char is preferable to the commonly used silica sand: pyrolysis of Kraft lignin with a bed of activated lignin char not only provides a pure char product, but also a higher dry bio-oil yield (with a relative increase of 43%), lower pyrolytic water production, and better bio-oil quality. The bio-oil obtained from Kraft lignin pyrolysis with a bed of activated lignin char has a lower average molecular weight, less tar, more phenolics, and less acidity than when sand is used as bed material. Copyright © 2015 Elsevier Ltd. All rights reserved.

TECHNOLOGICAL ASPECTS OF PRODUCING POLYMERIC COMPOSITIONS FOR BIOFILTER WITH IMPROVED IMMOBILIZATION PROPERTIES

Directory of Open Access Journals (Sweden)

L. N. Studenikina

2015-01-01

Full Text Available As the material loading of the filters, it is recommended to use a polymer composition having high immobilization capacity. The introduction of the polyolefins natural polysaccharides attached polymer composition, the ability to retain on its surface microflora, and additional content in the composition of nutrients will ensure the maintenance of microbial life in the event of termination of enrolment in the biofilter nutrients. We have investigated the technological aspects of polymer compositions based on polyethylene (PE, containing natural polysaccharides starch and alkaline pulp (waste vegetable oil refining, in the ratio of 80 : 20 wt.%, when the processing in modern high-speed equipment. In the study of rheological indicators, it was found that contained in the cellulose fatty acid and wax soften the composition, where the effective viscosity is filled with PE with the use of cellulose is celebrated on 30 ÷ 35 % lower than the composition with starch. For polymer compositions containing as starch and cellulose, at a temperature of processing 200 °С observed fracture of flow curves, and when the critical temperature 220 °С there is a rapid release, followed by decomposition of the compositions. It is noted that the composition containing the cellulose has a higher porosity than containing starch, which facilitates immobilization of the microflora. For use as a load of biofilters more recommended songs based on PE and cellulose because they have superior immobilization due to their porous structure, and the presence in the composition of polysaccharides and nutrients, as evidenced development on the surface of the samples of the composition of microscopic fungi (Aspergillus, Penicillium.

Thermomechanical interactions of particle bed-structural wall in a layered configuration. Pt. 1. Effect of particle bed thermal expansions

International Nuclear Information System (INIS)

Tehranian, F.

1995-01-01

Materials in the form of particle beds have been considered for shielding and tritium breeding as well as neutron multiplication in many of the conceptual reactor design studies. As the level of effort of the fusion blanket community in the area of out-of-pile and in-pile (ITER) testing of integrated test modules increases, so does the need for modelling capability for predicting the thermomechanical responses of the test modules under reactor environment.In this study, the thermomechanical responses of a particle bed-structural wall system in a layered configuration, subjected to bed temperature rise and/or external coolant pressure, were considered. Equations were derived which represent the dependence of the particle-to-particle and particle-to-wall contact forces and areas on the structural wall deformations and in turn on the thermomechanical loads. Using the derived equations, parametric analyses were performed to study the variations in the thermomechanical response quantities of a beryllium particle bed-stainless steel structural wall when subjected to thermomechanical loads. The results are presented in two parts. In Part I, presented in this paper, the derivation of the analytical equations and the effects of bed temperature rise are discussed. In Part II of this study, also presented in this symposium, the effects of external coolant pressure as well as the combined effects of bed temperature rise and coolant pressure on the thermomechanical responses are given.It is shown that, depending on the stiffness of the structural walls, uniform bed temperature rises in the range 100-400 C result in non-uniform effective thermal properties through the prticle bed and could increase the bed effective thermal conductivity by a factor of 2-5 and the bed-wall interface thermal conductance by even a larger factor. (orig.)

Culture scale-up and immobilisation of a mixed methanotrophic consortium for methane remediation in pilot-scale bio-filters.

Science.gov (United States)

Karthikeyan, Obulisamy Parthiba; Saravanan, Nadarajan; Cirés, Samuel; Alvarez-Roa, Carlos; Razaghi, Ali; Chidambarampadmavathy, Karthigeyan; Velu, Chinnathambi; Subashchandrabose, Gobalakrishnan; Heimann, Kirsten

2017-02-01

Robust methanotrophic consortia for methane (CH 4 ) remediation and by-product development are presently not readily available for industrial use. In this study, a mixed methanotrophic consortium (MMC), sequentially enriched from a marine sediment, was assessed for CH 4 removal efficiency and potential biomass-generated by-product development. Suitable packing material for bio-filters to support MMC biofilm establishment and growth was also evaluated. The enriched MMC removed ∼7-13% CH 4 under a very high gas flow rate (2.5 L min -1 ; 20-25% CH 4 ) in continuous-stirred tank reactors (∼10 L working volume) and the biomass contained long-chain fatty acids (i.e. C 16 and C 18 ). Cultivation of the MMC on plastic bio-balls abated ∼95-97% CH 4 in pilot-scale non-sterile outdoor-operated bio-filters (0.1 L min -1 ; 1% CH 4 ). Contamination by cyanobacteria had beneficial effects on treating low-level CH 4 , by providing additional oxygen for methane oxidation by MMC, suggesting that the co-cultivation of MMC with cyanobacterial mats does not interfere with and may actually be beneficial for remediation of CH 4 and CO 2 at industrial scale.

Effects of oxygen and water content on microbial distribution in the polyurethane foam cubes of a biofilter for SO2 removal.

Science.gov (United States)

Zhang, Jingying; Li, Lin; Liu, Junxin; Wang, Yanjie

2018-01-01

The performance of a biofilter for off-gas treatment relies on the activity of microorganisms and adequate O 2 and H 2 O. In present study, a microelectrode was applied to analyze O 2 in polyurethane foam cubes (PUFCs) packed in a biofilter for SO 2 removal. The O 2 distribution varied with the density and water-containing rate (WCR) of PUFCs. The O 2 concentration dropped sharply from 10.2 to 0.8mg/L from the surface to the center of a PUFC with 97.20% of WCR. The PUFCs with high WCR presented aerobic-anoxic-aerobic areas. Three-dimensional simulated images demonstrated that the structure of PUFCs with high WCR consisted of an aerobic "shell" and an anoxic "core", with high-density PUFCs featuring a larger anoxic area than low-density PUFCs. Moreover, the H 2 O distribution in the PUFC was uneven and affected the O 2 concentration. Whereas aerobic bacteria were observed in the PUFC surface, facultative anaerobic microorganisms were found at the PUFC core, where the O 2 concentration was relatively low. O 2 and H 2 O distributions differed in the PUFCs, and the distribution of microorganisms varied accordingly. Copyright © 2017. Published by Elsevier B.V.

Biostimulation strategies to enhance manganese removal in drinking water biofilters

DEFF Research Database (Denmark)

Breda, Inês Lousinha Ribeiro; Ramsay, Loren; Søborg, Ditte

to national drinking water criteria. The period during which virgin filter media matures into a fully functional biofilter is designated as the start-up period. The duration of a start-up for efficient manganese removal varies from weeks to more than a year. The aim of this study was to investigate...... growth and activity of specific bacteria. Biostimulation of virgin media to enhance initial manganese removal using different amendments strategies is possible especially in the early stages of filter development whereas autocatalytic processes appear to become dominant with time. The complex...

Balancing and dynamic behaviour of a biofilter plant for complete cleaning of municipal sewage; Bilanzierung und dynamisches Verhalten einer Biofilteranlage zur Vollreinigung von kommunalem Abwasser

Energy Technology Data Exchange (ETDEWEB)

Dickgreber, M.; Luebbecke, S. [Preussag Wassertechnik GmbH, Bremen (Germany)

1999-07-01

Where municipal sewage treatment plants need to be extended or enlarged, biofilter systems represent an economical alternative. They can be used both for supplementary residual elimination purposes and to treat complete sewage streams. For a biofilter system for complete cleaning of sewage employing the DENIPOR trademark -NCS process which has been in operation since 1996 (2*500 population value), studies in process dynamics are carried out and a complete balance is set up. (orig.) [German] Biofilter stellen bei notwendigen Erweiterungen und Ausbaumassnahmen von kommunalen Klaeranlagen eine wirtschaftliche Alternative dar. Sie koennen fuer weitergehende Restreinigungsaufgaben und zur Vollstrombehandlung eingesetzt werden. An einer seit 1996 in Betrieb befindlichen Biofilteranlage zur Vollreinigung von kommunalem Abwasser nach dem DENIPOR {sup trademark} -NCS Verfahren (2*500EW) werden Untersuchungen zur Prozessdynamik sowie eine vollstaendige Bilanzierung durchgefuehrt. (orig.)

Treating domestic effluent wastewater treatment by aerobic biofilter with bioballs medium

Science.gov (United States)

Permatasari, R.; Rinanti, A.; Ratnaningsih, R.

2018-01-01

This laboratory scale research aimed to treat wastewater effluent with advanced treatment utilizing aerobic biofilter with bio-balls medium to obtain effluent quality in accordance with DKI Jakarta Governor Regulation No. 122 of 2005. The seeding and acclimatization were conducted in 4 weeks. The effluent were accommodated in a 150 L water barrel supported by a submersible pump. The effluent were treated in two boxes shaped reactors made of glasses with 36 L of each capacity. These reactors were equipped with aquarium aerators, sampling tap is 10 cm from the base of reactors, and bio-balls with 3 cm diameter are made of PVC. Reactors operated continuously with variations of retention time of 4 hours, 8 hours, 12 hours, 18 hours, and 24 hours and also variations of Carbon: Nitrogen: Phosphor = C: N: P ratio were, 100:5:1, 100:8:1, 100:10:1, 100:12:1, 100:15:1. The results showed that the optimum variance of retention time was 24 hours and the ratio of C:N:P was 100:10:1 yielded the largest removal efficiency for 83,33% of COD, 87,33% of BOD, 82,5% of Ammonia, 79,1% of Nitrate, 92% of Nitrite, 84,82% of Oil and Grease. The concentration parameter resulted from outlet biofilter has met the domestic wastewater quality standard of DKI Jakarta.

Effect of particle stratification on debris-bed dryout

International Nuclear Information System (INIS)

Gabor, J.D.; Cassulo, J.C.; Pederson, D.R.

1982-01-01

Significant work has been performed on debris-bed dryout on beds of either uniformly sized particles or particles of a wide size range which are well mixed. This work has provided an understanding of the mechanisms of dryout and an empirical basis for containment analysis. However, the debris bed resulting from a HCDA would not consist of uniformly sized particles and for certain scenarios the bed could be stratified rather than well mixed. Tests have been conducted on the effect of particle size distribution on dryout and concluded that not only is the mean particle size an important parameter but also the standard deviation of the distribution and change in porosity. The D6 in-pile test at Sandia with a 114-mm deep stratified bed resulted in a reduced dryout heat flux compared to a uniformly mixed bed. Because of the many questions concerning the dryout behavior of stratified beds of wide size distribution out-of-pile experiments in which metal particles in water pools are inductively heated were initiated at Argonne

Treatment of micropollutants in municipal wastewater: study of a sequential batch biofilter

OpenAIRE

Contijoch Culleré, Andreu

2014-01-01

All the experimental part of this final project was done at Laboratoire de Biotechnologie Environnementale (LBE) from the École Polytechnique Fédérale de Lausanne (EPFL), Switzerland, during 6 months (November 2013- May 2014). A fungal biofilter composed of woodchips was designed in order to remove micropollutants from the effluents of waste water treatment plants. Two fungi were tested: Pleurotus ostreatus and Trametes versicolor in order to evaluate their efficiency for the r...

Influence of synthetic packing materials on the gas dispersion and biodegradation kinetics in fungal air biofilters

NARCIS (Netherlands)

Prenafeta-Boldú, F.X.; Illa, J.; Groenestijn, J.W. van; Flotats, X.

2008-01-01

The biodegradation of toluene was studied in two lab-scale air biofilters operated in parallel, packed respectively with perlite granules (PEG) and polyurethane foam cubes (PUC) and inoculated with the same toluene-degrading fungus. Differences on the material pore size, from micrometres in PEG to

Stabilizing effect of plasma discharge on bubbling fluidized granular bed

International Nuclear Information System (INIS)

Hu Mao-Bin; Dang Sai-Chao; Ma Qiang; Xia Wei-Dong

2015-01-01

Fluidized beds have been widely used for processing granular materials. In this paper, we study the effect of plasma on the fluidization behavior of a bubbling fluidized bed with an atmospheric pressure plasma discharger. Experiment results show that the bubbling fluidized bed is stabilized with the discharge of plasma. When the discharge current reaches a minimum stabilization current C ms , air bubbles in the bed will disappear and the surface fluctuation is completely suppressed. A simplified model is proposed to consider the effect of electric Coulomb force generated by the plasma. It is found that the Coulomb force will propel the particles to move towards the void area, so that the bubbling fluidized bed is stabilized with a high enough plasma discharge. (paper)

Application of bacteriophages to selectively remove Pseudomonas aeruginosa in water and wastewater filtration systems.

Science.gov (United States)

Zhang, Yanyan; Hunt, Heather K; Hu, Zhiqiang

2013-09-01

Water and wastewater filtration systems often house pathogenic bacteria, which must be removed to ensure clean, safe water. Here, we determine the persistence of the model bacterium Pseudomonas aeruginosa in two types of filtration systems, and use P. aeruginosa bacteriophages to determine their ability to selectively remove P. aeruginosa. These systems used beds of either anthracite or granular activated carbon (GAC), which were operated at an empty bed contact time (EBCT) of 45 min. The clean bed filtration systems were loaded with an instantaneous dose of P. aeruginosa at a total cell number of 2.3 (± 0.1 [standard deviation]) × 10(7) cells. An immediate dose of P. aeruginosa phages (1 mL of phage stock at the concentration of 2.7 × 10(7) PFU (Plaque Forming Units)/mL) resulted in a reduction of 50% (± 9%) and >99.9% in the effluent P. aeruginosa concentrations in the clean anthracite and GAC filters, respectively. To further evaluate the effects of P. aeruginosa phages, synthetic stormwater was run through anthracite and GAC biofilters where mixed-culture biofilms were present. Eighty five days after an instantaneous dose of P. aeruginosa (2.3 × 10(7) cells per filter) on day 1, 7.5 (± 2.8) × 10(7) and 1.1 (± 0.5) × 10(7) P. aeruginosa cells/g filter media were detected in the top layer (close to the influent port) of the anthracite and GAC biofilters, respectively, demonstrating the growth and persistence of pathogenic bacteria in the biofilters. A subsequent 1-h dose of phages, at the concentration of 5.1 × 10(6) PFU/mL and flow rate of 1.6 mL/min, removed the P. aeruginosa inside the GAC biofilters and the anthracite biofilters by 70% (± 5%) and 56% (± 1%), respectively, with no P. aeruginosa detected in the effluent, while not affecting ammonia oxidation or the ammonia-oxidizing bacterial community inside the biofilters. These results suggest that phage treatment can selectively remove pathogenic bacteria with minimal impact on beneficial

Removal of Hydrogen Sulfide from Septic Tank by Vermicomposting Bio Filter

Directory of Open Access Journals (Sweden)

Abdol Kazem Neisi

2016-09-01

Full Text Available Background & Aims of the Study: Hydrogen sulfide (H2S is a colorless and highly toxic, easily dissolved in water, flammable and explosive gas. Hydrogen sulfide gas is the main cause of odor emissions from municipal sewage plants. One method for removal of hydrogen sulfide gas is the use of biological systems, biofilter. The aim of this study was to survey removal hydrogen sulfide provide in septic tank by vermicomposting biofilter. Materials and Methods: In this study pilot-scale biofilter has been made of bed vermicompost and wood trash. To survey biofilter performance under real condition, the pilot installed in one wastewater pumping station of Ahwaz city, Iran. The study was carried out over 80 days. Inlet and outlet H2S concentration were measured on regular basis. To provide an optimal condition for bacterial growth, moisture was adjusted between 40% and 60% throughout the experiment. Results: Results showed that H2S concentration emitted from the pumping station during the study varied greatly between 33 and 54ppm .The maximum adsorption capacity of the biological bedding was recorded at 22.4 g/m3.hr and the mean efficiency of H2S removal account the startup time was 89.31% .The mean performance efficiency during the biological activity after the startup was recorded at 96.88%. Conclusion: use up biofilter with vermicompost bed and woodchip is an economic method for H2S removal of septic tanks. Removal efficiency of more than 96% is expected with this method.

Isolation and characterization of dimethyl sulfide (DMS)-degrading bacteria from soil and biofilter treating waste gas containing DMS from the laboratory and pulp and paper industry.

Science.gov (United States)

Giri, Balendu Shekher; Juwarkar, Asha A; Satpute, D B; Mudliar, S N; Pandey, R A

2012-07-01

Dimethyl sulfide (DMS) is one of the sulfurous pollutants present in the waste gas generated from the pulp and paper industry. DMS has environmental health implications; therefore, it is necessary to treat the waste gas containing DMS prior to discharge into the environment. A bench-scale biofilter was operated in the laboratory as well as in a pulp and paper industry for the treatment of DMS. Both the biofilters were packed with pre-sterilized wood chips and cow dung/compost of the same origin seeded with biomass developed from garden soil enriched with DMS. The biofilters were operated for the generation of process parameters, and the potential microorganisms isolated from both the biofilters have been purified and characterized for degradation of DMS. Further, these cultures were purified on a basal medium using DMS as a sole carbon source for the growth. Further, the purified cultures were characterized through standard fatty acid methyl esters (FAME)-gas chromatography method, and the isolates were found to be mesophilic, aerobic microbes. These microbes were identified as Bacillus sphaericus-GC subgroup F, Paenibacillus polymyxa, B. sphaericus-GC subgroup F, B. sphaericus-GC subgroup F, and Bacillus megaterium-GC subgroup A, respectively. The potential culture for degradation of DMS was identified as B. sphaericus by 16s rRNA molecular analysis.

Effects of biofilter media depth and moisture content on removal of gases from a swine barn.

Science.gov (United States)

Liu, Tongshuai; Dong, Hongmin; Zhu, Zhiping; Shang, Bin; Yin, Fubin; Zhang, Wanqin; Zhou, Tanlong

2017-12-01

Media depth (MD) and moisture content (MC) are two important factors that greatly influence biofilter performance. The purpose of this study was to investigate the combined effect of MC and MD on removing ammonia (NH 3 ), hydrogen sulfide (H 2 S), and nitrous oxide (N 2 O) from swine barns. Biofiltration performance of different MDs and MCs in combination based on a mixed medium of wood chips and compost was monitored. A 3 × 3 factorial design was adopted, which included three levels of the two factors (MC: 45%, 55%, and 67% [wet basis]; MD: 0.17, 0.33, and 0.50 m). Results indicated that high MC and MD could improve NH 3 removal efficiency, but increase outlet N 2 O concentration. When MC was 67%, the average NH 3 removal efficiency of three MDs (0.17, 0.33, and, 0.50 m) ranged from 77.4% to 78.7%; the range of average H 2 S removal efficiency dropped from 68.1-90.0% (1-34 days of the test period) to 36.8-63.7% (35-58 days of the test period); and the average outlet N 2 O concentration increased by 25.5-60.1%. When MC was 55%, the average removal efficiency of NH 3 , H 2 S, and N 2 O for treatment with 0.33 m MD was 72.8 ± 5.9%, 70.9 ± 13.3%, and -18.9 ± 8.1%, respectively; and the average removal efficiency of NH 3 , H 2 S, and N 2 O for treatment with 0.50 m MD was 77.7 ± 4.2%, 65.8 ± 13.7%, and -24.5 ±12.1%, respectively. When MC was 45%, the highest average NH 3 reduction efficiency among three MDs was 60.7% for 0.5 m MD, and the average N 2 O removal efficiency for three MDs ranged from -18.8% to -12.7%. In addition, the pressure drop of 0.33 m MD was significantly lower than that of 0.50 m MD (p moisture contents (45%, 55%, and 67% [wet basis]) were compared to remove gases from a swine barn. Using wood chips and compost mixture as the biofilters media, the combination of 0.33 m media depth and 55% media moisture content is recommended to obtain good reduction of NH 3 and H 2 S, and to simultaneously prevent elevated emission of N 2 O and large

Manganese oxidation and bacterial diversity on different filter media coatings during the start-up of drinking water biofilters

DEFF Research Database (Denmark)

Breda, I. L.; Ramsay, L.; Roslev, P.

2017-01-01

Manganese removal is a typical concern in drinking water production. Biofiltration may be used when treating groundwater sources but the onset of manganese removal in virgin biofilters can vary considerably. The aim of this study was to investigate the effect of different filter media on manganese...... by manganese oxide, while 48, 57 and 72 days were required by virgin quartz, calcium carbonate and polystyrene, respectively. The bacterial community was investigated using DAPI staining, quantitative polymerase chain reaction (qPCR), 16S rRNA gene pyrosequencing, and bacterial enrichments. Bacterial abundance...

Removal of gasoline vapors from air streams by biofiltration

Energy Technology Data Exchange (ETDEWEB)

Apel, W.A.; Kant, W.D.; Colwell, F.S.; Singleton, B.; Lee, B.D.; Andrews, G.F.; Espinosa, A.M.; Johnson, E.G.

1993-03-01

Research was performed to develop a biofilter for the biodegradation of gasoline vapors. The overall goal of this effort was to provide information necessary for the design, construction, and operation of a commercial gasoline vapor biofilter. Experimental results indicated that relatively high amounts of gasoline vapor adsorption occur during initial exposure of the biofilter bed medium to gasoline vapors. Biological removal occurs over a 22 to 40{degrees}C temperature range with removal being completely inhibited at 54{degrees}C. The addition of fertilizer to the relatively fresh bed medium used did not increase the rates of gasoline removal in short term experiments. Microbiological analyses indicated that high levels of gasoline degrading microbes are naturally present in the bed medium and that additional inoculation with hydrocarbon degrading cultures does not appreciably increase gasoline removal rates. At lower gasoline concentrations, the vapor removal rates were considerably lower than those at higher gasoline concentrations. This implies that system designs facilitating gasoline transport to the micro-organisms could substantially increase gasoline removal rates at lower gasoline vapor concentrations. Test results from a field scale prototype biofiltration system showed volumetric productivity (i.e., average rate of gasoline degradation per unit bed volume) values that were consistent with those obtained with laboratory column biofilters at similar inlet gasoline concentrations. In addition, total benzene, toluene, ethyl-benzene, and xylene (BTEX) removal over the operating conditions employed was 50 to 55%. Removal of benzene was approximately 10 to 15% and removal of the other members of the BTEX group was much higher, typically >80%.

Removal of gasoline vapors from air streams by biofiltration

Energy Technology Data Exchange (ETDEWEB)

Apel, W.A.; Kant, W.D.; Colwell, F.S.; Singleton, B.; Lee, B.D.; Andrews, G.F.; Espinosa, A.M.; Johnson, E.G.

1993-03-01

Research was performed to develop a biofilter for the biodegradation of gasoline vapors. The overall goal of this effort was to provide information necessary for the design, construction, and operation of a commercial gasoline vapor biofilter. Experimental results indicated that relatively high amounts of gasoline vapor adsorption occur during initial exposure of the biofilter bed medium to gasoline vapors. Biological removal occurs over a 22 to 40[degrees]C temperature range with removal being completely inhibited at 54[degrees]C. The addition of fertilizer to the relatively fresh bed medium used did not increase the rates of gasoline removal in short term experiments. Microbiological analyses indicated that high levels of gasoline degrading microbes are naturally present in the bed medium and that additional inoculation with hydrocarbon degrading cultures does not appreciably increase gasoline removal rates. At lower gasoline concentrations, the vapor removal rates were considerably lower than those at higher gasoline concentrations. This implies that system designs facilitating gasoline transport to the micro-organisms could substantially increase gasoline removal rates at lower gasoline vapor concentrations. Test results from a field scale prototype biofiltration system showed volumetric productivity (i.e., average rate of gasoline degradation per unit bed volume) values that were consistent with those obtained with laboratory column biofilters at similar inlet gasoline concentrations. In addition, total benzene, toluene, ethyl-benzene, and xylene (BTEX) removal over the operating conditions employed was 50 to 55%. Removal of benzene was approximately 10 to 15% and removal of the other members of the BTEX group was much higher, typically >80%.

Experimental measurement of effective thermal conductivity of packed lithium-titanate pebble bed

International Nuclear Information System (INIS)

Mandal, D.; Sathiyamoorthy, D.; Vinjamur, M.

2012-01-01

Lithium titanate is a promising solid breeder material for the fusion reactor blanket. Packed lithium titanate pebble bed is considered for the blanket. The thermal energy; that will be produced in the bed during breeding and the radiated heat from the reactor core absorbed must be removed. So, the experimental thermal property data are important for the blanket design. In past, a significant amount of works were conducted to determine the effective thermal conductivity of packed solid breeder pebble bed, in helium atmosphere, but no flow of gas was considered. With increase in gas flow rate, effective thermal conductivity of pebble bed increases. Particle size and void fraction also affect the thermal properties of the bed significantly. An experimental facility with external heat source was designed and installed. Experiments were carried out with lithium-titanate pebbles of different sizes at variable gas flow rates and at different bed wall temperature. It was observed that effective thermal conductivity of pebble bed is a function of particle Reynolds number and temperature. From the experimental data two correlations have been developed to estimate the effective thermal conductivity of packed lithium-titanate pebble bed for different particle Reynolds number and at different temperatures. The experimental details and results are discussed in this paper.

An investigation into the removal of Salmonella and enteric indicator bacteria from the separated liquid fraction of raw or anaerobically digested pig manure using novel on-farm woodchip biofilters.

Science.gov (United States)

McCarthy, G; Lawlor, P G; Carney, K N; Zhan, X; Gutierrez, M; Gardiner, G E

2015-05-01

The objective was to investigate the removal of Salmonella and enteric indicator bacteria from the liquid fraction of raw and anaerobically digested (AD) pig manure in woodchip biofilters over a 14 week (98 day) period. Antibiotic susceptible Salmonella Infantis was detected in one influent material (liquid fraction of raw manure) on two occasions but was not found in the effluent at any time point. Furthermore, mean coliform reductions of 56% were observed in the biofilters treating the liquid fraction of raw manure. However, a mean increase of 228% was found in those treating the liquid from AD manure, despite the fact that the microbial challenge to these biofilters was lower. In addition, relatively high coliform counts were still present in the effluent from both biofilter treatments, especially in the systems treating the liquid fraction of AD manure. However, findings for Escherichia coli and Enterococcus were more promising, with reductions observed for both treatments (10 and 18.5% for E. coli and 71 and 87% for Enterococcus). Moreover, E. coli and Enterococcus were at, or just above, the limit of detection in the final effluents. Overall, although, there are no microbial limits for discharge or washwaters, the woodchip filter effluent would appear safe for discharge to waterways or use on-farm as regards Salmonella, E. coli and Enterococcus but not coliform. In conclusion, woodchip biofilters offer potential as a low-cost sustainable novel treatment option for the removal of pathogens from the liquid fraction of pig manure. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of bedding quality on lying behavior of dairy cows.

Science.gov (United States)

Fregonesi, J A; Veira, D M; von Keyserlingk, M A G; Weary, D M

2007-12-01

Cows prefer to spend more time lying down in free stalls with more bedding, but no research to date has addressed the effects of bedding quality. Bedding in stalls often becomes wet either from exposure to the elements or from feces and urine. The aim of this study was to test the effect of wet bedding on stall preference and use. Four groups of 6 nonlactating Holstein cows were housed in free stalls bedded daily with approximately 0.1 m of fresh sawdust. Following a 5-d adaptation period, each group of cows was tested sequentially with access to stalls with either dry or wet sawdust bedding (86.4 +/- 2.1 vs. 26.5 +/- 2.1% dry matter), each for 2 d. These no-choice phases were followed by a 2-d free-choice phase during which cows had simultaneous access to stalls containing either wet or dry bedding. Stall usage was assessed by using 24-h video recordings scanned at 10-min intervals, and responses were analyzed by using a mixed model, with group (n = 4) as the observational unit. The minimum and maximum environmental temperatures during the experiment were 3.4 +/- 2.2 and 6.8 +/- 2.5 degrees C, respectively. When cows had access only to stalls with wet bedding, they spent 8.8 +/- 0.8 h/d lying down, which increased to 13.8 +/- 0.8 h/d when stalls with dry bedding were provided. Cows spent more time standing with their front 2 hooves in the stall when provided with wet vs. dry bedding (92 +/- 10 vs. 32 +/- 10 min/d). During the free-choice phase, all cows spent more time lying down in the dry stalls, spending 12.5 +/- 0.3 h/d in the dry stalls vs. 0.9 +/- 0.3 h/ d in stalls with wet bedding. In conclusion, dairy cows show a clear preference for a dry lying surface, and they spend much more time standing outside the stall when only wet bedding is available.

Soil-biofilters for elimination of xenobiotics from wastewaters

DEFF Research Database (Denmark)

Bester, Kai; Schäfer, D; Janzen, N.

treatment plants are not designed to eliminate these compounds. Even more of these compounds are discharged by storm waters and combined sewer overflows. It is generally suggested that separating sewers into waste water and rainwater systems might help to improve the situation. However in the last few years...... it has been demonstrated, that storm waters can be heavily polluted with biocides, lubricants and PAHs. In this study we investigated the possibilities to eliminate lipophilic fragrances, bactericides, UV blockers, lubricants etc, as well as more hydrophilic organophosphate flame retardants, biocides...... and other components with low cost soil biofilter techniques suited for on-site decentralised treatment of storm waters and combined sewer overflows. On the other hand the same systems and compounds were tested in for polishing treated waste water in respect of further elimination of xenobiotic compounds....

Numerical Simulations of the Effects of a Tidal Turbine Array on Near-Bed Velocity and Local Bed Shear Stress

Directory of Open Access Journals (Sweden)

Philip A. Gillibrand

2016-10-01

Full Text Available We apply a three-dimensional hydrodynamic model to consider the potential effects of energy extraction by an array of tidal turbines on the ambient near-bed velocity field and local bed shear stress in a coastal channel with strong tidal currents. Local bed shear stress plays a key role in local sediment dynamics. The model solves the Reynold-averaged Navier-Stokes (RANS equations on an unstructured mesh using mixed finite element and finite volume techniques. Tidal turbines are represented through an additional form drag in the momentum balance equation, with the thrust imparted and power generated by the turbines being velocity dependent with appropriate cut-in and cut-out velocities. Arrays of 1, 4 and 57 tidal turbines, each of 1.5 MW capacity, were simulated. Effects due to a single turbine and an array of four turbines were negligible. The main effect of the array of 57 turbines was to cause a shift in position of the jet through the tidal channel, as the flow was diverted around the tidal array. The net effect of this shift was to increase near-bed velocities and bed shear stress along the northern perimeter of the array by up to 0.8 m·s−1 and 5 Pa respectively. Within the array and directly downstream, near-bed velocities and bed shear stress were reduced by similar amounts. Changes of this magnitude have the potential to modify the known sand and shell banks in the region. Continued monitoring of the sediment distributions in the region will provide a valuable dataset on the impacts of tidal energy extraction on local sediment dynamics. Finally, the mean power generated per turbine is shown to decrease as the turbine array increased in size.

Evaluation of the bioremoval of Cr(VI) and TOC in biofilters under continuous operation using response surface methodology.

Science.gov (United States)

Leles, Daniela M A; Lemos, Diego A; Filho, Ubirajara C; Romanielo, Lucienne L; de Resende, Miriam M; Cardoso, Vicelma L

2012-06-01

In the present study, the bioremoval of Cr(VI) and the removal of total organic carbon (TOC) were achieved with a system composed by an anaerobic filter and a submerged biofilter with intermittent aeration using a mixed culture of microorganisms originating from contaminated sludge. In the aforementioned biofilters, the concentrations of chromium, carbon, and nitrogen were optimized according to response surface methodology. The initial concentration of Cr(VI) was 137.35 mg l(-1), and a bioremoval of 85.23% was attained. The optimal conditions for the removal of TOC were 4 to 8 g l(-1) of sodium acetate, >0.8 g l(-1) of ammonium chloride and 60 to 100 mg l(-1) of Cr(VI). The results revealed that ammonium chloride had the strongest effect on the TOC removal, and 120 mg l(-1) of Cr(VI) could be removed after 156 h of operation. Moreover, 100% of the Cr(VI) and the total chromium content of the aerobic reactor output were removed, and TOC removals of 80 and 87% were attained after operating the anaerobic and aerobic reactors for 130 and 142 h, respectively. The concentrations of cells in both reactors remained nearly constant over time. The residence time distribution was obtained to evaluate the flow through the bioreactors.

Assessing the Efficacy of the Aerobic Methanotrophic Biofilter in Methane Hydrate Environments

Energy Technology Data Exchange (ETDEWEB)

Valentine, David

2012-09-30

In October 2008 the University of California at Santa Barbara (UCSB) initiated investigations of water column methane oxidation in methane hydrate environments, through a project funded by the National Energy Technology Laboratory (NETL) entitled: assessing the efficacy of the aerobic methanotrophic biofilter in methane hydrate environments. This Final Report describes the scientific advances and discoveries made under this award as well as the importance of these discoveries in the broader context of the research area. Benthic microbial mats inhabit the sea floor in areas where reduced chemicals such as sulfide reach the more oxidizing water that overlies the sediment. We set out to investigate the role that methanotrophs play in such mats at locations where methane reaches the sea floor along with sulfide. Mats were sampled from several seep environments and multiple sets were grown in-situ at a hydrocarbon seep in the Santa Barbara Basin. Mats grown in-situ were returned to the laboratory and used to perform stable isotope probing experiments in which they were treated with 13C-enriched methane. The microbial community was analyzed, demonstrating that three or more microbial groups became enriched in methane?s carbon: methanotrophs that presumably utilize methane directly, methylotrophs that presumably consume methanol excreted by the methanotrophs, and sulfide oxidizers that presumably consume carbon dioxide released by the methanotrophs and methylotrophs. Methanotrophs reached high relative abundance in mats grown on methane, but other bacterial processes include sulfide oxidation appeared to dominate mats, indicating that methanotrophy is not a dominant process in sustaining these benthic mats, but rather a secondary function modulated by methane availability. Methane that escapes the sediment in the deep ocean typically dissolved into the overlying water where it is available to methanotrophic bacteria. We set out to better understand the efficacy of this

Biofiltration of gasoline and ethanol-amended gasoline vapors.

Science.gov (United States)

Soares, Marlene; Woiciechowski, Adenise L; Kozliak, Evguenii I; Paca, Jan; Soccol, Carlos R

2012-01-01

Assuming the projected increase in use of ethanol as a biofuel, the current study was conducted to compare the biofiltration efficiencies for plain and 25% ethanol-containing gasoline. Two biofilters were operated in a downflow mode for 7 months, one of them being compost-based whereas the other using a synthetic packing material, granulated tire rubber, inoculated with gasoline-degrading microorganisms. Inlet concentrations measured as total hydrocarbon (TH) ranged from 1.9 to 5.8 g m(-3) at a constant empty bed retention time of 6.84 min. Contrary to the expectations based on microbiological considerations, ethanol-amended gasoline was more readily biodegraded than plain hydrocarbons, with the respective steady state elimination capacities of 26-43 and 14-18 gTH m(-3) h(-1) for the compost biofilter. The efficiency of both biofilters significantly declined upon the application of higher loads of plain gasoline, yet immediately recovering when switched back to ethanol-blended gasoline. The unexpected effect of ethanol in promoting gasoline biodegradation was explained by increasing hydrocarbon partitioning into the aqueous phase, with mass transfer being rate limiting for the bulk of components. The tire rubber biofilter, after a long acclimation, surpassed the compost biofilter in performance, presumably due to the 'buffering' effect of this packing material increasing the accessibility of gasoline hydrocarbons to the biofilm. With improved substrate mass transfer, biodegradable hydrocarbons were removed in the tire rubber biofilter's first reactor stage, with most of the remaining poorly degradable smaller-size hydrocarbons being degraded in the second stage.

Methodologies for pre-validation of biofilters and wetlands for stormwater treatment.

Directory of Open Access Journals (Sweden)

Kefeng Zhang

Full Text Available Water Sensitive Urban Design (WSUD systems are frequently used as part of a stormwater harvesting treatment trains (e.g. biofilters (bio-retentions and rain-gardens and wetlands. However, validation frameworks for such systems do not exist, limiting their adoption for end-uses such as drinking water. The first stage in the validation framework is pre-validation, which prepares information for further validation monitoring.A pre-validation roadmap, consisting of five steps, is suggested in this paper. Detailed methods for investigating target micropollutants in stormwater, and determining challenge conditions for biofilters and wetlands, are provided.A literature review was undertaken to identify and quantify micropollutants in stormwater. MUSIC V5.1 was utilized to simulate the behaviour of the systems based on 30-year rainfall data in three distinct climate zones; outputs were evaluated to identify the threshold of operational variables, including length of dry periods (LDPs and volume of water treated per event.The paper highlights that a number of micropollutants were found in stormwater at levels above various worldwide drinking water guidelines (eight pesticides, benzene, benzo(apyrene, pentachlorophenol, di-(2-ethylhexyl-phthalate and a total of polychlorinated biphenyls. The 95th percentile LDPs was exponentially related to system design area while the 5th percentile length of dry periods remained within short durations (i.e. 2-8 hours. 95th percentile volume of water treated per event was exponentially related to system design area as a percentage of an impervious catchment area.The out-comings of this study show that pre-validation could be completed through a roadmap consisting of a series of steps; this will help in the validation of stormwater treatment systems.

Analysis of Metabolites and Carbon Balance in the Biofilteration of Cumene Using Loofa Sponge as Biofilter Media.

Science.gov (United States)

Shahi, Amrita; Rai, B N; Singh, R S

2016-09-01

A laboratory-scale biofilter study was performed to treat cumene-inoculated mixed culture of bacterial community and loofa sponge (Luffa cylindrica) as support media for a period of 120 days in five distinct phases. The removal efficiency was obtained in the range of 40-85 % with maximum elimination capacity of 700 g m(-3) h(-1) at the inlet load of 1167 g m(-3) h(-1). The result demonstrated that loofa sponge is good support media for the removal of cumene at higher loading rates. Loofa sponge was characterized via chemical analysis and analytical techniques such as XRD; FTIR; XPS; and CHN, and the result obtained confirms its suitability as biofilter media. The SEM results of loofa with inoculum shows the formation of a biofilm layer on the surface of loofa. The GC-MS analysis of leachate confirms the presence of different organic compounds such as acetaldehyde and 4-hydroxy-2-oxopentanoic acids which are stable metabolites during cumene biodegradation. About 12.69 % of carbon present in inlet cumene was converted to biomass.

Effectiveness of Bed Bug Pesticides

Science.gov (United States)

Before EPA allows a bed bug claim on a label, the product must be supported by data showing it will kill bed bugs when applied according to the label. Also consider factors such as extent of infestation, site preparation, and insect life stages.

Two-Phase Flow Effect on the Ex-Vessel Corium Debris Bed Formation in Severe Accident

International Nuclear Information System (INIS)

Kim, Eunho; Park, Jin Ho; Kim, Moo Hwan; Park, Hyun Sun; Ma, Weimin; Bechta, Sevostian V.

2014-01-01

In Korean IVR-ERVC(In-Vessel Retention of molten corium through External Reactor Vessel Cooling) strategy, if the situation degenerates into insufficient external vessel cooling, the molten core mixture can directly erupt into the flooded cavity pool from the weakest point of the vessel. Then, FCI (molten Fuel Coolant Interaction) will fragment the corium jet into small particulates settling down to make porous debris bed on the cavity basemat. To secure the containment integrity against the MCCI (Molten Core - Concrete Interaction), cooling of the heat generating porous corium debris bed is essential and it depends on the characteristics of the bed itself. For the characteristics of corium debris bed, many previous experimental studies with simulant melts reported the heap-like shape mostly. There were also following experiments to develop the correlation for the heap-like shaped debris bed. However, recent studies started to consider the effect of the decay heat and reported some noticeable results with the two-phase flow effect on the debris bed formation. The Kyushu University and JAEA group reported the experimental studies on the 'self-leveling' effect which is the flattening effect of the particulate bed by the inside gas generation. The DECOSIM simulation study of RIT (Royal Institute of Technology, Sweden) with Russian researchers showed the 'large cavity pool convection' effect, which is driven by the up-rising gas bubble flow from the pre-settled debris bed, on the particle settling trajectories and ultimately final bed shape. The objective of this study is verification of the two-phase flow effect on the ex-vessel corium debris bed formation in the severe accident. From the analysis on the test movie and resultant particle beds, the two-phase flow effect on the debris bed formation, which has been reported in the previous studies, was verified and the additional findings were also suggested. For the first, in quiescent pool the

Fungal biocatalysts in the biofiltration of VOC-polluted air.

Science.gov (United States)

Kennes, Christian; Veiga, María C

2004-09-30

Gas-phase biofilters used for the treatment of waste gases were originally packed with compost or other natural filter beds containing indigenous microorganisms. Over the past decade much effort has been made to develop new carrier materials, more performant biocatalysts and new types of bioreactors. Elimination capacities reached nowadays are 5 to 10 times higher than those originally reported with conventional compost biofilters. With the recently developed inert filter beds, inoculation is a prerequisite for successful start-up and operation. Either non-defined mixed cultures or pure bacterial cultures have originally been used. The search for efficient fungal biocatalysts started only a few years ago, mainly for the biofiltration of waste gases containing hydrophobic compounds, such as styrene, alpha-pinene, benzene, or alkylbenzenes. In this review, recently isolated new fungal strains able to degrade alkylbenzenes and other related volatile organic pollutants are described, as well as their major characteristics and their use as biocatalysts in gas-phase biofilters for air pollution control. In biofiltration, the most extensively studied organism belongs to the genus Exophiala, although strains of Scedosporium, Paecilomyces, Cladosporium, Cladophialophora, and white-rot fungi are all potential candidates for use in biofilters. Encouraging results were obtained in most of the cases in which some of those organisms were present in gas-phase biofilters. They allow reaching high elimination capacities and are resistant to low pH values and to reduce moisture content.

A prediction model for the effective thermal conductivity of mono-sized pebble beds

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiaoliang; Zheng, Jie; Chen, Hongli, E-mail: hlchen1@ustc.edu.cn

2016-02-15

Highlights: • One new method to couple the contact area with bed strain is developed. • The constant coefficient to correlate the effect of gas flow is determined. • This model is valid for various cases, and its advantages are showed obviously. - Abstract: A model is presented here to predict the effective thermal conductivity of porous medium packed with mono-sized spherical pebbles, and it is valid when pebbles’ size is far less than the characteristic length of porous medium just like the fusion pebble beds. In this model, the influences of parameters such as properties of pebble and gas materials, bed porosity, pebble size, gas flow, contact area, thermal radiation, contact resistance, etc. are all taken into account, and one method to couple the contact areas with bed strains is also developed and implemented preliminarily. Compared with available theoretical models, CFD numerical simulations and experimental data, this model is verified to be successful to forecast the bed effective thermal conductivity in various cases and its advantages are also showed obviously. Especially, the convection in pebble beds is focused on and a constant coefficient C to correlate the effect of gas flow is determined for the fully developed region of beds by numerical simulation, which is close to some experimental data.

Tile Effect of P reconsolidation on the Thermal Conductivity of Particulate Beds

International Nuclear Information System (INIS)

Weidenfeld, G.

2001-09-01

The thermal conductivity of particulate beds is an important property for many industrial handling processes as well as storage of particulate materials. This property can be affected by a few conditions, such as, temperature and external axial pressure. In the first part of this work, a background for the thermal conductivity of particulate bed is given. This includes a review of experimental and theoretical studies on the thermal conductivity of particulate beds. It is also a reviewed parameters that influence the thermal conductivity of particulate beds, such as, temperature. This study presents a new experimental apparatus that enables to measure the thermal conductivity in steady-state while the particulate bed is under axial consolidation stresses. The experimental apparatus was analyzed and characterized experimentally and by numerical simulations. An analytical model, that predicts the thermal conductivity of particulate beds under axial consolidation stress was developed. The model results were compared to the experimental results for 0.5 and 1 mm steel spheres and showed a good agreement. The experimental results showed a significant effect of the compression state on the bed and its pre-consolidation for 0.5 and 1 mm steel spheres. The effect of the compression state on the bed and its pre-consolidation was even more significant for limestone powder

The Effect of Bedding Structure on Mechanical Property of Coal

Directory of Open Access Journals (Sweden)

Zetian Zhang

2014-01-01

Full Text Available The mechanical property of coal, influencing mining activity considerably, is significantly determined by the natural fracture distributed within coal mass. In order to study the effecting mechanism of bedding structure on mechanical property of coal, a series of uniaxial compression tests and mesoscopic tests have been conducted. The experimental results show that the distribution characteristic of calcite particles, which significantly influences the growth of cracks and the macroscopic mechanical properties of coal, is obviously affected by the bedding structure. Specifically, the uniaxial compression strength of coal sample is mainly controlled by bedding structure, and the average peak stress of specimens with axes perpendicular to the bedding planes is 20.00 MPa, which is 2.88 times the average amount of parallel ones. The test results also show a close relationship between the bedding structure and the whole deformation process under uniaxial loading.

Influence of gas pressure on the effective thermal conductivity of ceramic breeder pebble beds

International Nuclear Information System (INIS)

Dai, Weijing; Pupeschi, Simone; Hanaor, Dorian; Gan, Yixiang

2017-01-01

Highlights: • This study explicitly demonstrates the influence of the gas pressure on the effective thermal conductivity of pebble beds. • The gas pressure influence is shown to correlated to the pebble size. • The effective thermal conductivity is linked to thermal-mechanical properties of pebbles and packing structure. - Abstract: Lithium ceramics have been considered as tritium breeder materials in many proposed designs of fusion breeding blankets. Heat generated in breeder pebble beds due to nuclear breeding reaction must be removed by means of actively cooled plates while generated tritiums is recovered by purge gas slowly flowing through beds. Therefore, the effective thermal conductivity of pebble beds that is one of the governing parameters determining heat transport phenomenon needs to be addressed with respect to mechanical status of beds and purge gas pressure. In this study, a numerical framework combining finite element simulation and a semi-empirical correlation of gas gap conduction is proposed to predict the effective thermal conductivity. The purge gas pressure is found to vary the effective thermal conductivity, in particular with the presence of various sized gaps in pebble beds. Random packing of pebble beds is taken into account by an approximated correlation considering the packing factor and coordination number of pebble beds. The model prediction is compared with experimental observation from different sources showing a quantitative agreement with the measurement.

Influence of gas pressure on the effective thermal conductivity of ceramic breeder pebble beds

Energy Technology Data Exchange (ETDEWEB)

Dai, Weijing [School of Civil Engineering, The University of Sydney, Sydney (Australia); Pupeschi, Simone [Institute for Applied Materials, Karlsruhe Institute of Technology (KIT) (Germany); Hanaor, Dorian [School of Civil Engineering, The University of Sydney, Sydney (Australia); Institute for Materials Science and Technologies, Technical University of Berlin (Germany); Gan, Yixiang, E-mail: yixiang.gan@sydney.edu.au [School of Civil Engineering, The University of Sydney, Sydney (Australia)

2017-05-15

Highlights: • This study explicitly demonstrates the influence of the gas pressure on the effective thermal conductivity of pebble beds. • The gas pressure influence is shown to correlated to the pebble size. • The effective thermal conductivity is linked to thermal-mechanical properties of pebbles and packing structure. - Abstract: Lithium ceramics have been considered as tritium breeder materials in many proposed designs of fusion breeding blankets. Heat generated in breeder pebble beds due to nuclear breeding reaction must be removed by means of actively cooled plates while generated tritiums is recovered by purge gas slowly flowing through beds. Therefore, the effective thermal conductivity of pebble beds that is one of the governing parameters determining heat transport phenomenon needs to be addressed with respect to mechanical status of beds and purge gas pressure. In this study, a numerical framework combining finite element simulation and a semi-empirical correlation of gas gap conduction is proposed to predict the effective thermal conductivity. The purge gas pressure is found to vary the effective thermal conductivity, in particular with the presence of various sized gaps in pebble beds. Random packing of pebble beds is taken into account by an approximated correlation considering the packing factor and coordination number of pebble beds. The model prediction is compared with experimental observation from different sources showing a quantitative agreement with the measurement.

Biodegradation of formaldehyde from contaminated air using a laboratory scale static-bed bioreactor

Directory of Open Access Journals (Sweden)

Yaghoub Hajizadeh

2014-01-01

Full Text Available Aims: The objective of the present study was to evaluate the performance of an aerobic fixed-bed bioreactor (FBR enriched with microorganisms of sewage sludge in biodegradation of formaldehyde in air stream with various retention times and airflow rates in laboratory scale. Materials and Methods: An aerobic biofilter 60 cm in height and 14 cm internal diameter made of steel was constructed and packed with a mixture of pumice and compost as a medium and utilized in this study. The microorganism′s growth, which is derived from the sludge of a municipal wastewater treatment plant, was initiated by adding nutrient. During the first few days of run, the airflow containing different concentrations of formaldehyde (from 24 ± 3 to 224 ± 5 mg/m 3 was introduced to the reactor to ensure biological adaptation. Sampling was performed through a series of two impingers containing adsorbent, and analyzed by chromotropic acid assay using DR-5000. Results: The maximum removal and elimination capacity of formaldehyde was yielded at 0.48 ± 0.06 g/m 3 /h inlet loading rate and 180 s of empty bed retention time (EBRT. These values for stabilized days were almost 88% and 0.42 g/m 3 /h, respectively. Conclusion: The results showed that by increasing the inlet concentration of formaldehyde and reducing the EBRT, the formaldehyde removal capacity of the system decreases. Aerobic bioreactor with appropriate bed volume and compatible with inlet pollutant mass flow rate in optimum retention time will admissibly degrade and reduce the formaldehyde concentration from contaminated gas phase, such as gases produced in municipal wastewater treatment facilities.

The effect of hydraulic bed movement on the quality of chest compressions.

Science.gov (United States)

Park, Maeng Real; Lee, Dae Sup; In Kim, Yong; Ryu, Ji Ho; Cho, Young Mo; Kim, Hyung Bin; Yeom, Seok Ran; Min, Mun Ki

2017-08-01

The hydraulic height control systems of hospital beds provide convenience and shock absorption. However, movements in a hydraulic bed may reduce the effectiveness of chest compressions. This study investigated the effects of hydraulic bed movement on chest compressions. Twenty-eight participants were recruited for this study. All participants performed chest compressions for 2min on a manikin and three surfaces: the floor (Day 1), a firm plywood bed (Day 2), and a hydraulic bed (Day 3). We considered 28 participants of Day 1 as control and each 28 participants of Day 2 and Day 3 as study subjects. The compression rates, depths, and good compression ratios (>5-cm compressions/all compressions) were compared between the three surfaces. When we compared the three surfaces, we did not detect a significant difference in the speed of chest compressions (p=0.582). However, significantly lower values were observed on the hydraulic bed in terms of compression depth (p=0.001) and the good compression ratio (p=0.003) compared to floor compressions. When we compared the plywood and hydraulic beds, we did not detect significant differences in compression depth (p=0.351) and the good compression ratio (p=0.391). These results indicate that the movements in our hydraulic bed were associated with a non-statistically significant trend towards lower-quality chest compressions. Copyright © 2017 Elsevier Inc. All rights reserved.

Preliminary acclimation strategies for successful startup in conventional biofilters.

Science.gov (United States)

Elías, Ana; Barona, Astrid; Gallastegi, Gorka; Rojo, Naiara; Gurtubay, Luis; Ibarra-Berastegi, Gabriel

2010-08-01

The question of how to obtain the best inocula for conventional biofilters arises when an acclimation/adaptation procedure is to be applied. Bearing in mind that no standardized procedure for acclimating inocula exists, certain preliminary strategies for obtaining an active inoculum from wastewater treatment sludge are proposed in this work. Toluene was the contaminant to be degraded. Concerning the prior separation of sludge phases, no obvious advantage was found in separating the supernatant phase of the sludge before acclimation. As far as a continuous or discontinuous acclimation mode is concerned, the latter is recommended for rapidly obtaining acclimated sludge samples by operating the system for no longer than 1 month. The continuous mode rendered similar degradation rates, although it required longer operating time. Nevertheless, the great advantage of the continuous system lay in the absence of daily maintenance and the ready availability of the activated sample.

Loading and Unloading Weaned Pigs: Effects of Bedding Types, Ramp Angle, and Bedding Moisture

Directory of Open Access Journals (Sweden)

Arlene Garcia

2014-12-01

Full Text Available The use of non-slip surfaces during loading and unloading of weaned pigs plays an important role in animal welfare and economics of the pork industry. Currently, the guidelines available only suggest the use of ramps below 20° to load and unload pigs. Three ramp angles (0°, 10° or 20°, five bedding materials (nothing, sand, feed, wood shavings or wheat straw hay, two moistures (dry or wet bedding; >50% moisture over two seasons (>23.9 °C summer, <23.9 °C winter were assessed for slips/falls/vocalizations (n = 6,000 pig observations. “Score” was calculated by the sum of slips, falls, and vocalizations. With the exception of using feed as a bedding, all beddings provided some protection against elevated slips, falls, and vocalizations (P < 0.01. Providing bedding reduced (P < 0.05 scores regardless of whether the bedding was dry or wet. Scores increased as the slope increased (P < 0.01. Provision of bedding, other than feed, at slopes greater than zero, decreased slips, falls and vocalizations. The total time it took to load and unload pigs was

The effect of 8 days of strict bed rest on the incretin effect in healthy volunteers.

Science.gov (United States)

Nielsen, Signe Tellerup; Harder-Lauridsen, Nina Majlund; Benatti, Fabiana Braga; Wedell-Neergaard, Anne-Sophie; Lyngbæk, Mark Preben; Møller, Kirsten; Pedersen, Bente Klarlund; Krogh-Madsen, Rikke

2016-03-15

Bed rest and physical inactivity are the consequences of hospital admission for many patients. Physical inactivity induces changes in glucose metabolism, but its effect on the incretin effect, which is reduced in, e.g., Type 2 diabetes, is unknown. To investigate how 8 days of strict bed rest affects the incretin effect, 10 healthy nonobese male volunteers underwent 8 days of strict bed rest. Before and after the intervention, all volunteers underwent an oral glucose tolerance test (OGTT) followed by an intravenous glucose infusion (IVGI) on the following day to mimic the blood glucose profile from the OGTT. Blood glucose, serum insulin, serum C-peptide, plasma incretin hormones [glucagon-like peptide (GLP-1) and glucose-dependent insulinotropic peptide (GIP)], and serum glucagon were measured serially during both the OGTT and the IVGI. The incretin effect is calculated as the relative difference between the area under the curve for the insulin response during the OGTT and that of the corresponding IVGI, respectively. Concentrations of glucose, insulin, C-peptide, and GIP measured during the OGTT were higher after the bed rest intervention (all P effect (P = 0.6). In conclusion, 8 days of bed rest induces insulin resistance, but we did not see evidence of an associated change in the incretin effect. Copyright © 2016 the American Physiological Society.

Effect of Bedding Material on Dust and Ammonia Emission from Broiler Houses

NARCIS (Netherlands)

Harn, van J.; Aarnink, A.J.A.; Mosquera Losada, J.; Riel, van J.W.; Ogink, N.W.M.

2012-01-01

Ammonia emission, Bedding material, Broilers, Dust emission The objective of this study was to determine the effects of different bedding materials on fine dust (PM10 and PM2.5) and ammonia emissions from broiler houses. The effects on broiler performance and footpad lesions were also studied. The

Effect of various drying bed on thermodynamic characteristics

Directory of Open Access Journals (Sweden)

Ali Motevali

2017-09-01

Full Text Available In this study thermodynamic parameter and energy consumption in drying of two plant dill and mint in three bed drying including fix, semi fix and fluid with using a hot air drying was investigated. Experimental was conducted in three bed drying including fix, semi fix and fluid and four levels temperature (30, 40, 50 and 60 °C. Maximum energy consumption in dill drying at 40 °C and fluid bed to be 16.41 MJ and minimum energy consumption at 30 °C and fix bed to be 2.77 MJ. Also minimum energy consumption in mint drying at 60 °C and fix bed to be 3.64 MJ and maximum energy consumption at 40 °C and fluid bed to be 28.65 MJ. The highest energy, drying and thermal efficiency for both mint and dill was achieved at 60 °C on the fixed bed, whereas the lowest efficiency was at 40 °C and on the fluidized bed. Also the highest power and specific heat consumption for both mint and dill was achieved at 40 °C on the fluid bed, whereas the lowest efficiency was at 30 °C and on the fluidized bed.

Experimental study of flow field characteristics on bed configurations in the pebble bed reactor

International Nuclear Information System (INIS)

Jia, Xinlong; Gui, Nan; Yang, Xingtuan; Tu, Jiyuan; Jia, Haijun; Jiang, Shengyao

2017-01-01

Highlights: • PTV study of flow fields of pebble bed reactor with different configurations are carried out. • Some criteria are proposed to quantify vertical velocity field and flow uniformity. • The effect of different pebble bed configurations is also compared by the proposed criteria. • The displacement thickness is used analogically to analyze flow field characteristics. • The effect of mass flow variation in the stagnated region of the funnel flow is measured. - Abstract: The flow field characteristics are of fundamental importance in the design work of the pebble bed high temperature gas cooled reactor (HTGR). The different effects of bed configurations on the flow characteristics of pebble bed are studied through the PTV (Particle Tracking Velocimetry) experiment. Some criteria, e.g. flow uniformity (σ) and mass flow level (α), are proposed to estimate vertical velocity field and compare the bed configurations. The distribution of the Δθ (angle difference between the individual particle velocity and the velocity vector sum of all particles) is also used to estimate the resultant motion consistency level. Moreover, for each bed configuration, the thickness of displacement is analyzed to measure the effect of the funnel flow zone based on the boundary layer theory. Detailed information shows the quantified characteristics of bed configuration effects on flow uniformity and other characteristics; and the sequence of levels of each estimation criterion is obtained for all bed configurations. In addition, a good design of the pebble bed configuration is suggested and these estimation criteria can be also applied and adopted in testing other geometry designs of pebble bed.

(Case Study: Wastewater Pump Station of Khoramabad

Directory of Open Access Journals (Sweden)

Masoud Taheriyoun

2014-10-01

Full Text Available Evaluation of a Biofilter System for Removal of Hydrogen Sulfide Gas (Case Study: Wastewater Pump Station of Khorramabad Abstract The biofilter system is one of the methods commonly used for the removal of hydrogen sulfide as the main source of odors emitted from wastewater facilities. The system is based on using the contaminant material as bedding to feed microorganisms. To achieve the desirable removal efficiency, it is, therefore, essential to create the proper conditions for the bacteria to grow on the bedding. In this study, a pilot-scale biofilter made of compost and woodchip (with a compost/woodchip ratio of 5:1 was used as the bedding material at Khorrmabad wastewater pumping station to investigate the performance of the system under real conditions. The experiment was carried out over 75 days during which time the input and output H2S concentrations were measured on a regular basis. Moisture was adjusted between 40% and 60% throughout the experiment to provide optimal conditions for bacterial growth. The results showed that the concentration of H2S emitted from the pumping station during 24 hours varied greatly between 0 and 48 PPM. The maximum adsorption capacity of the biological bedding was recorded at 2.874 g/m3.hr and the mean efficiency of H2S removal including the startup time was 89%. The mean performance efficiency during the biological activity after the startup was recorded at 98%.

The effect of bedding system selected by manual muscle testing on sleep-related cardiovascular functions.

Science.gov (United States)

Kuo, Terry B J; Li, Jia-Yi; Lai, Chun-Ting; Huang, Yu-Chun; Hsu, Ya-Chuan; Yang, Cheryl C H

2013-01-01

Different types of mattresses affect sleep quality and waking muscle power. Whether manual muscle testing (MMT) predicts the cardiovascular effects of the bedding system was explored using ten healthy young men. For each participant, two bedding systems, one inducing the strongest limb muscle force (strong bedding system) and the other inducing the weakest limb force (weak bedding system), were identified using MMT. Each bedding system, in total five mattresses and eight pillows of different firmness, was used for two continuous weeks at the participant's home in a random and double-blind sequence. A sleep log, a questionnaire, and a polysomnography were used to differentiate the two bedding systems. Heart rate variability and arterial pressure variability analyses showed that the strong bedding system resulted in decreased cardiovascular sympathetic modulation, increased cardiac vagal activity, and increased baroreceptor reflex sensitivity during sleep as compared to the weak bedding system. Different bedding systems have distinct cardiovascular effects during sleep that can be predicted by MMT.

Effects of random pebble distribution on the multiplication factor in HTR pebble bed reactors

Energy Technology Data Exchange (ETDEWEB)

Auwerda, G.J., E-mail: g.j.auwerda@tudelft.n [Department of Physics of Nuclear Reactors at the Delft University of Technology, Mekelweg 15, Delft (Netherlands); Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der [Department of Physics of Nuclear Reactors at the Delft University of Technology, Mekelweg 15, Delft (Netherlands)

2010-08-15

In pebble bed reactors the pebbles have a random distribution within the core. The usual approach in modeling the bed is homogenizing the entire bed. To quantify the errors arising in such a model, this article investigates the effect on k{sub eff} of three phenomena in random pebble distributions: non-uniform packing density, neutron streaming in between the pebbles, and variations in Dancoff factor. For a 100 cm high cylinder with reflective top and bottom boundary conditions 25 pebble beds were generated. Of each bed three core models were made: a homogeneous model, a zones model including density fluctuations, and an exact model with all pebbles modeled individually. The same was done for a model of the PROTEUS facility. k{sub eff} calculations were performed with three codes: Monte Carlo, diffusion, and finite element transport. By comparing k{sub eff} of the homogenized and zones model the effect of including density fluctuations in the pebble bed was found to increase k{sub eff} by 71 pcm for the infinite cylinder and 649 pcm for PROTEUS. The large value for PROTEUS is due to the low packing fraction near the top of the pebble bed, causing a significant lower packing fraction for the bulk of the pebble bed in the homogenized model. The effect of neutron streaming was calculated by comparing the zones model with the exact model, and was found to decrease k{sub eff} by 606 pcm for the infinite cylinder, and by 1240 pcm for PROTEUS. This was compared with the effect of using a streaming correction factor on the diffusion coefficient in the zones model, which resulted in {Delta}{sub streaming} values of 340 and 1085 pcm. From this we conclude neutron streaming is an important effect in pebble bed reactors, and is not accurately described by the correction factor on the diffusion coefficient. Changing the Dancoff factor in the outer part of the pebble bed to compensate for the lower probability of neutrons to enter other fuel pebbles caused no significant changes

Use of planted biofilters in integrated recirculating aquaculture-hydroponics systems in the Mekong Delta, Vietnam

DEFF Research Database (Denmark)

Trang, N.T.D.; Brix, Hans

2014-01-01

The feasibility of using planted biofilters for purification of recirculated aquaculture water in the Mekong Delta of Vietnam was assessed. The plant trenches were able to clean tilapia aquaculture water and to maintain good water quality in the fish tanks without renewal of the water. NH4-N was ...... rates of 725 kg N and 234 kg P ha-1 year-1. This research demonstrates that integrated recirculating aquaculture-hydroponics (aquaponics) systems provide significant water savings and nutrient recycling as compared with traditional fish ponds....

Removal of volatile organic compounds at extreme shock-loading using a scaled-up pilot rotating drum biofilter.

Science.gov (United States)

Sawvel, Russell A; Kim, Byung; Alvarez, Pedro J J

2008-11-01

A pilot-scale rotating drum biofilter (RDB), which is a novel biofilter design that offers flexible flow-through configurations, was used to treat complex and variable volatile organic compound (VOC) emissions, including shock loadings, emanating from paint drying operations at an Army ammunition plant. The RDB was seeded with municipal wastewater activated sludge. Removal efficiencies up to 86% and an elimination capacity of 5.3 g chemical oxygen demand (COD) m(-3) hr(-1) were achieved at a filter-medium contact time of 60 sec. Efficiency increased at higher temperatures that promote higher biological activity, and decreased at lower pH, which dropped down to pH 5.5 possibly as a result of carbon dioxide and volatile fatty acid production and ammonia consumption during VOC degradation. In comparison, other studies have shown that a bench-scale RDB could achieve a removal efficiency of 95% and elimination capacity of 331 g COD m(-3) hr(-1). Sustainable performance of the pilot-scale RDB was challenged by the intermittent nature of painting operations, which typically resulted in 3-day long shutdown periods when bacteria were not fed. This challenge was overcome by adding sucrose (2 g/L weekly) as an auxiliary substrate to sustain metabolic activity during shutdown periods.

PERBANDINGAN DESAIN IPAL ANAEROBIC BIOFILTER DENGAN ROTATING BIOLOGICAL CONTACTOR UNTUK LIMBAH CAIR TEKSTIL DI SURABAYA

Directory of Open Access Journals (Sweden)

Yogie Restu Firmansyah

2017-01-01

Full Text Available Effluen Instalasi Pengolahan Air Limbah (IPAL di Pabrik Tekstil X belum memenuhi kriteria yang ada, terutama untuk masalah warna. Sistem pengolahan IPAL menggunakan Anaerobic Biofilter memiliki kelebihan menyisihkan bahan organik yang tinggi, kebutuhan lahan yang relatif tidak besar, dan biaya operasi yang murah dibandingkan dengan sistem lumpur aktif yang menggunakan proses aerasi. Rotating Biological Contactor (RBC juga memiliki kelebihan yang sama dengan anaerobic biofilter. Perbandingan antara kedua sistem tersebut diperlukan untuk mengetahui sistem yang paling efektif untuk mengolah air limbah di Pabrik Textil X. Pengolahan adsorbsi batok arang kelapa dipilih untuk menghilangkan warna. Perencanaan ini dilakukan dengan menggunakan metode yang sistematis dimulai pengumpulan data primer dan sekunder yang berupa data karakteristik dan debit air limbah, lalu dilakukan perhitungan dan penggambaran Detail Engineering Desan (DED, volume pekerjaan dan Rancangan Anggaran Biaya (RAB, setelah itu dilakukan pembahasan untuk membandingkan kelebihan dan kekurangan dari unit anaerobic Biofilter yang dilengkapi adsorbsi arang batok kelapa dan Rotating Biological Contactor yang dilengkapi adsorbsi arang batok kelapa, lalu diambil kesimpulan dan saran yang relevan dengan tujuan dari perancanaan ini. Dari perhitungan DED didapat dimensi untuk masing masing unit IPAL sebagai berikut Bak ekualisasi (2,6 m x 2,6 m x 2 m, Septic tank (1,75 m x 1,5m x 2,5m, Anaerobic Filter 4 kompartemen (4,5m x 2,5m x 2,5m, , RBC 2 shaft  (2,75m x 2,75 m x 1m, Adsorbsi (3,5 mx 6,75m x 0,55m. Biaya investasi alternative 1 sebesar Rp   700.193.694,29, biaya operasi sebesar Rp 50.222.462,40, biaya perawatan sebesar Rp 3.495.000,00. Alternatif 2 biaya investasi sebesar Rp 777.526.655,53, biaya operasi sebesar Rp Rp 53.012.599,20  , biaya perawatan sebesar Rp 3.495.000,00. Kelebihan anaerobic filter adalah biaya investasi yang lebih kecil, kebutuhan lahan yang lebih sedikit yaitu

Infant's bed climate and bedding in the Japanese home.

Science.gov (United States)

Nakamura Ikeda, Rie; Fukai, Kiyoko; Okamoto Mizuno, Kazue

2012-06-01

to assess the bed climate of infants in their homes in Japan. descriptive, exploratory, non-experimental research design. the data were collected at the participants' homes under normal circumstances. nineteen healthy infants between the ages of two and five months. Their mothers, who joined a parenting class organised by a maternity clinic in Okayama, Japan, consented to participate in this study. we visited the infants' homes and interviewed their mothers concerning the types and use of bedding. The temperature and relative humidity of the bed climate at the back and foot of the bedding, and in the room were measured every minute for four consecutive days. Differences among the bed climates measured during three seasons (spring, summer, and autumn) were assessed by one-way analysis of variance. The bed temperature was higher for infants than for adults. No significant difference in temperature was noted among the three seasons. The bed temperature was about 36.0°C when waterproof sheets and futon mattresses for children or adult were used. The average relative humidity of the bed climate at the back was highest in summer, followed by that in spring and autumn; the differences were significant. The use of waterproof sheets and futon mattresses for children in summer increased the relative humidity to 80% or more. The use of infant beds, sunoko drainboards, and cotton futon mattresses in summer was effective in reducing the bed humidity. these results suggest that nurse-midwives should advise the parents on comfortable bed climates for their infants, as well as how to select and use bedding for them. Copyright © 2010 Elsevier Ltd. All rights reserved.

The effect of patient migration in bed on torso elevation.

Science.gov (United States)

Wiggermann, Neal; Kotowski, Susan; Davis, Kermit; VanGilder, Catherine

2015-01-01

Elevating the hospital head of bed (HOB) to at least 30° is recommended practice to reduce the risk of ventilator-associated pneumonia (VAP) in mechanically ventilated patients. However, this common practice prescribes the position of the bed and not of the patient, which could be significantly different. The aim of this research was to determine the relationship between patient migration in bed and anatomic torso angle. Ten healthy participants were positioned in a hospital bed that was raised from flat to 30° and 45° HOB elevations. Prior to bed movement, participants were aligned to different locations along the length of the bed to represent different amounts of migration. A motion capture system was used to measure torso angle and migration toward the foot of the bed. The relationship between torso angle and migration was estimated by linear regression. Patient migration resulted in lower torso angles for both 30° and 45° HOB articulations. A migration of 10 cm resulted in a loss of 9.1° and 13.0° of torso angle for HOB articulations of 30° and 45°, respectively (for 30° articulations: (Equation is included in full-text article.)= -0.91, R = .96; for 45° articulations: (Equation is included in full-text article.)= -1.30, R = .98). Migration toward the foot of the bed flattens the torso. To maintain a torso angle that is likely to protect against VAP, healthcare providers need to manage both HOB angle and migration. Protocols and equipment that minimize patient migration will help support effective clinical practice. Future research on patient migration, as it relates to VAP or other outcomes, should measure patient torso angle to allow accurate translation of the results to care practice.

Effects of pressure drop and superficial velocity on the bubbling fluidized bed incinerator.

Science.gov (United States)

Wang, Feng-Jehng; Chen, Suming; Lei, Perng-Kwei; Wu, Chung-Hsing

2007-12-01

Since performance and operational conditions, such as superficial velocity, pressure drop, particles viodage, and terminal velocity, are difficult to measure on an incinerator, this study used computational fluid dynamics (CFD) to determine numerical solutions. The effects of pressure drop and superficial velocity on a bubbling fluidized bed incinerator (BFBI) were evaluated. Analytical results indicated that simulation models were able to effectively predict the relationship between superficial velocity and pressure drop over bed height in the BFBI. Second, the models in BFBI were simplified to simulate scale-up beds without excessive computation time. Moreover, simulation and experimental results showed that minimum fluidization velocity of the BFBI must be controlled in at 0.188-3.684 m/s and pressure drop was mainly caused by bed particles.

Effect of Fluidized Bed Stirring on Drying Process of Adhesive Particles

Directory of Open Access Journals (Sweden)

P. Hoffman

2017-04-01

Full Text Available This paper presents an attempt to optimize fluidized bed drying of wet and adhesive particles (with an initial diameter of about 580 mm with the use of stirring, and discusses the influence of stirring on the total drying time. The goal was to demonstrate the positive effect of stirring a fluidized bed to the drying time, to find the optimal parameters (stirrer design, speed, and size. Experiments were conducted on a drying chamber in batch operation. The objective was to evaluate the effect of stirring on the total drying time. The drying chambers were 85 mm, 100 mm, and 140 mm in diameter. An optimal stirrer shape and speed were specified. Our arrangement of the fluidized bed resulted in a decrease in drying time by up to 40 %.

A comparative study on the effective thermal conductivity of a single size beryllium pebble bed

International Nuclear Information System (INIS)

Abou-Sena, A.; Ying, A.; Abdou, M.

2004-01-01

Solid breeder blankets generally use beryllium-helium pebble beds to ensure sufficient tritium breeding. The data of the effective thermal conductivity, k eff , of beryllium pebble beds is important to the design of fusion blankets. It serves as a database for benchmarking the models of pebble beds. The objective of this paper is to review and compare the available data (obtained by several studies) of the effective thermal conductivity of beryllium pebble beds in order to address the current status of these data. Two comparisons are presented: one for the data of k eff versus bed mean temperature and the second one for the data of k eff versus external applied pressures. The data (k eff versus bed temperature) reported by Enoeda et al., Dalle Donne et al., and UCLA, have a similar particle size and packing fraction. Despite their similarity, the standard deviation values of their data are around 32%. Also, the data of the effective thermal conductivity as a function of mechanical pressure have standard deviation values of ∼50%. From the presented comparisons, significant discrepancies among the available data of k eff of the beryllium pebble beds were observed. These discrepancies may be attributed to the apparent differences among available studies, such as experiment technique, packing fraction, particle characteristics, bed dimensions, and temperature range and gradient across the bed. (author)

Biofiltration of air contaminated with methanol and toluene

Directory of Open Access Journals (Sweden)

Pakamas Chetpattananondh

2005-12-01

Full Text Available Biofiltration of air contaminated with VOCs is inexpensive compared with the conventional techniques and very effective for treating large volumes of moist air streams with low concentrations of VOCs. In this study, biofiltration for the purification of polluted air from methanol, a hydrophilic VOC, and toluene, a hydrophobic VOC, was investigated. The experiments were operated using three separated stainless steel biofilters, for methanol, toluene, and a mixture of methanol and toluene, respectively. Biofilter consisted of a mixture of palm shells and activated sludge as a filter-bed material. Only the indigenous microorganisms of the bed medium without any addition of extra inoculum were used throughout the whole process. The polluted air inlet concentration was varied from 0.3-4.7 g/m3 with flow rates ranging from 0.06-0.45 m3/h, equivalent to the empty bed residence times of 9-71 sec. Polluted air was successfully treated by biofiltration, 100% removal efficiencies would be obtained when the air flow rate was lower than 0.45 m3/h. The presence of toluene did not affect the removal rate of methanol while the removal rate of toluene was decreased with the presence of methanol in air stream according to the competition phenomenon.

Evaluation on Biofilter in Recirculating Integrated Multi-Trophic Aquaculture

Directory of Open Access Journals (Sweden)

S. Sumoharjo

2013-06-01

Full Text Available Integrated multi-trophic aquaculture pays more attention as a bio-integrated food production system that serves as a model of sustainable aquaculture, minimizes waste discharge, increases diversity and yields multiple products. The objectives of this research were to analyze the efficiency of total ammonia nitrogen biofiltration and its effect on carrying capacity of fish rearing units. Pilot-scale bioreactor was designed with eight run-raceways (two meters of each that assembled in series. Race 1-3 were used to stock silky worm (Tubifex sp as detrivorous converter, then race 4-8 were used to plant three species of leaf-vegetable as photoautotrophic converters, i.e; spinach (Ipomoea reptana, green mustard (Brassica juncea and basil (Ocimum basilicum. The three plants were placed in randomized block design based on water flow direction. Mass balance of nutrient analysis, was applied to figure out the efficiency of bio-filtration and its effect on carrying capacity of rearing units. The result of the experiment showed that 86.5 % of total ammonia nitrogen removal was achieved in 32 days of culturing period. This efficiency able to support the carrying capacity of the fish tank up to 25.95 kg/lpm with maximum density was 62.69 kg/m3 of fish biomass productionDoi: http://dx.doi.org/10.12777/ijse.4.2.2013.80-85 [How to cite this article: Sumoharjo, S.  and Maidie, A. (2013. Evaluation on Biofilter in Recirculating Integrated Multi-Trophic Aquaculture.  International Journal of  Science and Engineering, 4(2,80-85. Doi: http://dx.doi.org/10.12777/ijse.4.2.2013.80-85

Design of combination biofilter and subsurface constructed wetland-multilayer filtration with vertical flow type using Vetiveria zizanioides (akar wangi)

Science.gov (United States)

Astuti, A. D.; Lindu, M.; Yanidar, R.; Faruq, M.

2018-01-01

As environmental regulation has become stricter in recent years, there is an increasing concern about the issue of wastewater treatment in urban areas. Senior High School as center of student activity has a potential source to generated domestic wastewater from toilet, bathroom and canteen. Canteen wastewater contains high-organic content that to be treated before discharged. Based on previous research the subsurface constructed wetland-multilayer filtration with vertical flow is an attractive alternative to provide efficient treatment of canteen wastewater. The effluent concentration complied with regulation according to [9]. Due to limited land, addition of preliminary treatment such as the presence of biofilter was found to improve the performance. The aim of this study was to design combination biofilter and subsurface constructed wetland-multilayer filtration with vertical flow type using vetiveria zizanioides (akar wangi) treating canteen wastewater. Vetiveria zizanioides (akar wangi) is used because from previous research, subsurface constructed wetland-multilayer filtration (SCW-MLF) with vertical flow type using vetiveria zizanioides (akar wangi) can be an alternative canteen wastewater treatment that is uncomplicated in technology, low cost in operational and have a beautiful landscape view, besides no odors or insects were presented during the operation.

Chemical characteristics of beddings for swine: effects of bedding depths and of addition of inoculums in a pilot-scale.

Science.gov (United States)

Corrêa, E K; Corezzolla, J L; Corrêa, M N; Bianchi, I; Gil-Turnes, C; Lucia, T

2012-11-01

The effect of depths and of addition of inoculums on the chemical content of swine beddings was evaluated. For beddings 0.25m (25D) and 0.50m (50D) deep, three treatments were tested in two repeats with the same beddings: control (no inoculums); T1 (250g of Bacillus cereus var. toyoii at 8.4×10(7)CFU/g); and T2 (250g of a pool of Bacillus sp. at 8.4×10(7)CFU/g) (250g for 25D and 500g for 50D). For 25D, the C:N ratio was lower, but N, K and C contents were greater than for 50D (P0.05). In the second repeat, beddings presented lower C:N ratio and greater N, P and K contents than in the first repeat (P<0.05). Thus, the compost produced after using 25D twice had greater fertilizer value than that of 50D. Copyright © 2012 Elsevier Ltd. All rights reserved.

Branched-chain amino acid supplementation during bed rest: effect on recovery

Science.gov (United States)

Stein, T. P.; Donaldson, M. R.; Leskiw, M. J.; Schluter, M. D.; Baggett, D. W.; Boden, G.

2003-01-01

Bed rest is associated with a loss of protein from the weight-bearing muscle. The objectives of this study are to determine whether increasing dietary branched-chain amino acids (BCAAs) during bed rest improves the anabolic response after bed rest. The study consisted of a 1-day ambulatory period, 14 days of bed rest, and a 4-day recovery period. During bed rest, dietary intake was supplemented with either 30 mmol/day each of glycine, serine, and alanine (group 1) or with 30 mmol/day each of the three BCAAs (group 2). Whole body protein synthesis was determined with U-(15)N-labeled amino acids, muscle, and selected plasma protein synthesis with l-[(2)H(5)]phenylalanine. Total glucose production and gluconeogenesis from alanine were determined with l-[U-(13)C(3)]alanine and [6,6-(2)H(2)]glucose. During bed rest, nitrogen (N) retention was greater with BCAA feeding (56 +/- 6 vs. 26 +/- 12 mg N. kg(-1). day(-1), P < 0.05). There was no effect of BCAA supplementation on either whole body, muscle, or plasma protein synthesis or the rate of 3-MeH excretion. Muscle tissue free amino acid concentrations were increased during bed rest with BCAA (0.214 +/- 0.066 vs. 0.088 +/- 0.12 nmol/mg protein, P < 0.05). Total glucose production and gluconeogenesis from alanine were unchanged with bed rest but were significantly reduced (P < 0.05) with the BCAA group in the recovery phase. In conclusion, the improved N retention during bed rest is due, at least in part, to accretion of amino acids in the tissue free amino acid pools. The amount accreted is not enough to impact protein kinetics in the recovery phase but does improve N retention by providing additional essential amino acids in the early recovery phase.

Effects of Fluidization Velocity and Bed Particle Size on Bed Defluidization during Biomass Combustion in FB boilers; Effekten av fluidiseringshastighet och kornstorlek paa agglomereringsrisk vid biobraensleeldning i FB-pannor

Energy Technology Data Exchange (ETDEWEB)

Eriksson, Morgan; Oehman, Marcus [Umeaa Univ. (Sweden). Applied Physics and Electronics; Wikman, Karin; Berg, Magnus [AaF-Energi och Miljoe AB, Stockholm (Sweden)

2004-11-01

Studies on the effect of bed particle size and fluidization velocity on the agglomeration/defluidization risk during biomass combustion in BFB/CFB plants have not previously been published. Therefore, the objective of this project has been to determine the influence of these two parameters on the risk for agglomeration in typical biofuel fired fluidized beds. The study has also resulted in information on how variations in the coating characteristics of the bed particles are depending on the fuel ash content and the particle size of the bed material. Furthermore, the conditions at large scale commercial plants have been surveyed with respect to the choice of bed material, fluidization velocity, bed sand consumption etc. Bed materials have been sampled from seven full-scale boilers, four CFB and three BFB. The samples have been sieved to achieve sieve curves, analyzed with respect to the coating characteristics, and studied by experiments in a bench-scale fluidized bed. It could be concluded from the analyses that there are no significant differences in the coating thickness or the coating composition between fine and coarse particles in the bed samples. The bench-scale agglomeration experiments showed that increased fluidization velocity results in bed agglomeration at a higher temperature. This effect was stronger at relatively low fluidization velocities. The fluidization velocity has probably no significant effect on the risk for agglomeration at normal gas velocities in a commercial CFB boiler. Though, it could have an influence on the agglomeration in for example the recycling part of a CFB, where the gas velocity is relatively low. Also in BFB-boilers the fluidization velocity is often low enough to have a significant effect on the risk for agglomeration. By the experiments in this project it has not been possible to determine if the bed particle size has an influence on the agglomeration. Further studies with modified methods are required to find out if the

Exercise Effects on the Course of Gray Matter Changes Over 70 Days of Bed Rest

Science.gov (United States)

Koppelmans, V.; Ploutz-Snyder, L.; DeDios, Y. E.; Wood, S. J.; Reuter-Lorenz, P. A.; Kofman, I.; Bloomberg, J. J.; Mulavara, A. P.; Seidler, R. D.

2014-01-01

Long duration spaceflight affects posture control, locomotion, and manual control. The microgravity environment is an important causal factor for spaceflight induced sensorimotor changes through direct effects on peripheral changes that result from reduced vestibular stimulation and body unloading. Effects of microgravity on sensorimotor function have been investigated on earth using bed rest studies. Long duration bed rest serves as a space-flight analogue because it mimics microgravity in body unloading and bodily fluid shifts. It has been hypothesized that the cephalad fluid shift that has been observed in microgravity could potentially affect central nervous system function and structure, and thereby indirectly affect sensorimotor or cognitive functioning. Preliminary results of one of our ongoing studies indeed showed that 70 days of long duration head down-tilt bed rest results in focal changes in gray matter volume from pre-bed rest to various time points during bed rest. These gray matter changes that could reflect fluid shifts as well as neuroplasticity were related to decrements in motor skills such as maintenance of equilibrium. In consideration of the health and performance of crewmembers both inand post-flight we are currently conducting a study that investigates the potential preventive effects of exercise on gray matter and motor performance changes that we observed over the course of bed rest. Numerous studies have shown beneficial effects of aerobic exercise on brain structure and cognitive performance in healthy and demented subjects over a large age range. We therefore hypothesized that an exercise intervention in bed rest could potentially mitigate or prevent the effects of bed rest on the central nervous system. Here we present preliminary outcomes of our study.

Treatment of chemical-pharmaceutical wastewater in packed bed anaerobic reactors

Energy Technology Data Exchange (ETDEWEB)

Nacheva, P.M.; Pena-Loera, B.; Moralez-Guzman, F. [Mexican Institute for Water Technology, Jiutepec (Mexico)

2006-07-01

Biological degradation in packed bed anaerobic mesophilic reactors with five different support materials was studied for the treatment of chemical-pharmaceutical wastewater with high COD (23-31 g/L), which contains toxic organic compounds. Experimental up-flow bio-filters were operated at different organic loads for a two-year period. Removals of 80-98% were obtained in the reactors with sand, anthracite and black tezontle, but at relatively low organic loads, less than 3.6 kg m{sup -3} d{sup -1}. The reactor with granular activated carbon (GAC) had a better performance; efficiencies higher than 95% were obtained at loads up to 17kg m{sup -3} d{sup -1} and higher than 80% with loads up to 26 kg m{sup -3} d{sup -1}. Second in performance was the reactor with red tezontle which allows COD removals higher than 80% with loads up to 6 kg m{sup -3} d{sup -1}. The use of GAC as support material allows greater biodegradation rates than the rest of the materials and it makes the process more resistant to organic load increases, inhibition effects and toxicity. Methanogenic activity was inhibited at loads higher than 21.9 kg m{sup -3} d{sup -1} in the GAC-reactor and at loads higher than 3.6 kg m{sup -3} d{sup -1} in the rest of the reactors. At loads lower than the previously mentioned, high methane production yield was obtained, 0.32-0.35 m{sup 33}CH4/kg CODremoved.

Fluidized bed catalytic cracking regenerator model: grid effects

Energy Technology Data Exchange (ETDEWEB)

Errazu, A.F. (Universidad Nacional del Sur, Conicet, Argentina); De Lasa, H.I.; Sarti, F.

1979-04-01

A grid model including thermal effects is proposed. The aim is the simulation of a fluidized catalytic cracking regenerator similar to the industrial unit of Destileria La Palta, YPF, Argentina. It is demonstrated that a simple C.S.T.R. model without bypass of gas feed entering the bed provides a good approach for representing the fluidized bed including the grid region. In addition, by means of the C.S.T.R. model, it is shown that there exist two characteristic operating regions: a zone where (C/sub 0//sup 0/ to C/sub c/) depends on the initial coke concentration and a zone where (C/sub c//sub 0/ to C/sub c/) is controlled by oxygen supply. 40 references, 6 figures, 5 tables.

Bacterial community structure of a full-scale biofilter treating pig house exhaust air

DEFF Research Database (Denmark)

Kristiansen, Anja; Pedersen, Kristina Hadulla; Nielsen, Per Halkjær

2011-01-01

Biological air filters represent a promising tool for treating emissions of ammonia and odor from pig facilities. Quantitative fluorescence in situ hybridization (FISH) and 16S rRNA gene sequencing were used to investigate the bacterial community structure and diversity in a full-scale biofilter ...... consisting of two consecutive compartments (front and back filter). The analysis revealed a highly specialized bacterial community of limited diversity, dominated by a few groups of Betaproteobacteria (especially Comamonas) and diverse Bacteroidetes. Actinobacteria, Gammaproteobacteria......, and betaproteobacterial ammoniaoxidizers (Nitrosomonas eutropha/Nitrosococcus mobilis-lineage) were also quantitatively important. Only a few quantitative differences existed between the two filter compartments at the group level, with a lower relative abundance of Actinobacteria and a higher relative abundance...

A comparative study of fungal and bacterial biofiltration treating a VOC mixture

International Nuclear Information System (INIS)

Estrada, José M.; Hernández, Sergio; Muñoz, Raúl; Revah, Sergio

2013-01-01

Highlights: ► Bacterial biofilter showed better EC and ΔP than fungal biofilter. ► The preferential biodegradation order was: propanal > hexanol > MIBK > toluene. ► Propanal partially inhibited the biodegradation of the rest of VOCs. ► The two-stage biofilter showed a higher stability than the individual units. -- Abstract: Bacterial biofilters usually exhibit a high microbial diversity and robustness, while fungal biofilters have been claimed to better withstand low moisture contents and pH values, and to be more efficient coping with hydrophobic volatile organic compounds (VOCs). However, there are only few systematic evaluations of both biofiltration technologies. The present study compared fungal and bacterial biofiltration for the treatment of a VOC mixture (propanal, methyl isobutyl ketone-MIBK, toluene and hexanol) under the same operating conditions. Overall, fungal biofiltration supported lower elimination capacities than its bacterial counterpart (27.7 ± 8.9 vs 40.2 ± 5.4 g C m −3 reactor h −1 ), which exhibited a final pressure drop 60% higher than that of the bacterial biofilter due to mycelial growth. The VOC mineralization ratio was also higher in the bacterial bed (≈63% vs ≈43%). However, the substrate biodegradation preference order was similar for both biofilters (propanal > hexanol > MIBK > toluene) with propanal partially inhibiting the consumption of the rest of the VOCs. Both systems supported an excellent robustness versus 24 h VOC starvation episodes. The implementation of a fungal/bacterial coupled system did not significantly improve the VOC removal performance compared to the individual biofilter performances

A comparative study of fungal and bacterial biofiltration treating a VOC mixture

Energy Technology Data Exchange (ETDEWEB)

Estrada, José M. [Departamento de Procesos y Tecnología, Universidad Autónoma Metropolitana-Cuajimalpa, Artificios 40, Col. Miguel Hidalgo, Delegación Álvaro Obregón (Mexico); Departamento de Ingeniería Química y Tecnología del Medio Ambiente – Universidad de Valladolid, Valladolid (Spain); Hernández, Sergio [Departmento de Procesos e Hidráulica – Universidad Autónoma Metropolitana – Iztapalapa Mexico D.F. Mexico (Mexico); Muñoz, Raúl [Departamento de Ingeniería Química y Tecnología del Medio Ambiente – Universidad de Valladolid, Valladolid (Spain); Revah, Sergio, E-mail: srevah@xanum.uam.mx [Departamento de Procesos y Tecnología, Universidad Autónoma Metropolitana-Cuajimalpa, Artificios 40, Col. Miguel Hidalgo, Delegación Álvaro Obregón (Mexico)

2013-04-15

Highlights: ► Bacterial biofilter showed better EC and ΔP than fungal biofilter. ► The preferential biodegradation order was: propanal > hexanol > MIBK > toluene. ► Propanal partially inhibited the biodegradation of the rest of VOCs. ► The two-stage biofilter showed a higher stability than the individual units. -- Abstract: Bacterial biofilters usually exhibit a high microbial diversity and robustness, while fungal biofilters have been claimed to better withstand low moisture contents and pH values, and to be more efficient coping with hydrophobic volatile organic compounds (VOCs). However, there are only few systematic evaluations of both biofiltration technologies. The present study compared fungal and bacterial biofiltration for the treatment of a VOC mixture (propanal, methyl isobutyl ketone-MIBK, toluene and hexanol) under the same operating conditions. Overall, fungal biofiltration supported lower elimination capacities than its bacterial counterpart (27.7 ± 8.9 vs 40.2 ± 5.4 g C m{sup −3} reactor h{sup −1}), which exhibited a final pressure drop 60% higher than that of the bacterial biofilter due to mycelial growth. The VOC mineralization ratio was also higher in the bacterial bed (≈63% vs ≈43%). However, the substrate biodegradation preference order was similar for both biofilters (propanal > hexanol > MIBK > toluene) with propanal partially inhibiting the consumption of the rest of the VOCs. Both systems supported an excellent robustness versus 24 h VOC starvation episodes. The implementation of a fungal/bacterial coupled system did not significantly improve the VOC removal performance compared to the individual biofilter performances.

The characteristics of bed agglomeration during fluidized bed combustion of eucalyptus bark

International Nuclear Information System (INIS)

Chaivatamaset, Pawin; Tia, Suvit

2015-01-01

The bed agglomeration behaviors were investigated experimentally when eucalyptus bark was burning tested in a laboratory scale fluidized bed reactor. The focuses of this work were the influences of operating conditions and bed materials on the bed agglomeration tendency and the elucidation in the behaviors of fuel inorganic elements and the governing mode of the agglomeration. It was found that the defluidization caused by the bed agglomeration was clearly detectable from the decrease in measured bed pressure. The growth of bed particle and accumulation of agglomerates during combustion provided the partial to complete defluidization. The defluidization was promoted by the increase of bed temperature and bed particle size, and the decrease of fluidizing air velocity. The SEM-EDS analyses revealed that the bed agglomeration was mainly attributed to the formation of potassium silicate compounds as liquid phase during the combustion. This was initiated by the chemical reaction between the bed particle and the released ash constituents. In this study, the inorganic migration from fuel particle to bed particle was likely dominated by the condensation/reaction. The thermodynamic examination by ternary phase diagram analysis corroborated that the liquid phase formation of the ash derived materials controlled the agglomeration. The alumina sand prevented the bed agglomeration since it was inactive in the formation of viscous molten substances during combustion at the observed temperatures. - Highlights: • The behaviors of bed agglomeration were studied during the fluidized bed combustion of eucalyptus bark. • The increase in bed temperature and sand size, and the decrease of air velocity promoted bed defluidization. • The formation of molten potassium silicate compounds conduced to the bed agglomeration. • Condensation/reaction was the dominant inorganic migration mechanism from fuel particle to bed particle. • The alumina sand prevented effectively the bed

Environmental protection stability of river bed and banks using convex, concave, and linear bed sills.

Science.gov (United States)

Keshavarzi, Alireza; Noori, Lila Khaje

2010-12-01

River bed scourings are a major environmental problem for fish and aquatic habitat resources. In this study, to prevent river bed and banks from scouring, different types of bed sills including convex, concave and linear patterns were installed in a movable channel bed in a laboratory flume. The bed sills were tested with nine different arrangements and under different flow conditions. To find the most effective bed sill pattern, the scouring depth was measured downstream of the bed sill for a long experimental duration. The scour depth was measured at the middle and at the end of each experimental test for different ratios of the arch radius to the channel width [r/w]. The experimental results indicated that the convex pattern with r/w=0.35 produced minimum bed scouring depth at the center line whereas the concave pattern with r/w=0.23 produced the minimum scour depth at the wall banks. Therefore, the convex pattern was the most effective configuration for prevention of scouring at the center line of the river while the concave pattern was very effective to prevent scouring at the river banks. These findings can be suggested to be used in practical applications.

Exercise Effects on the Brain and Sensorimotor Function in Bed Rest

Science.gov (United States)

Koppelmans, V.; Cassady, K.; De Dios, Y. E.; Szecsy, D.; Gadd, N.; Wood, S. J.; Reuter-Lorenz, R. A.; Kofman, I.; Bloomberg, J. J.; Mulavara, A. P.;

The Effects of Long Duration Bed Rest on Brain Functional Connectivity and Sensorimotor Functioning

Science.gov (United States)

Cassady, K.; Koppelmans, V.; De Dios, Y.; Stepanyan, V.; Szecsy, D.; Gadd, N.; Wood, S.; Reuter-Lorenz, P.; Castenada, R. Riascos; Kofman, I.;

Effects of setting new source performance standards for fluidized-bed combustion systems

Energy Technology Data Exchange (ETDEWEB)

1978-02-01

This study was undertaken for the US Environmental Protection Agency to examine the potential consequences of revisions in New Source Performance Standards (NSPS) on fluidized-bed combustor-based steam electric generators of greater than 250,000,000 Btu. A study of the appropriateness and differential effects of alternate regulatory approaches to the standards-setting process was made. Problems dealing with an emerging technology such as fluidized-bed combustion were emphasized. Finally, an examination was made of the potential benefits of fluidized-bed combustion (FBC) systems relative to conventional coal-fired systems equipped with scrubbers. Information is included on the relative advantages and disadvantages of utility-sized fluidized-bed combustors, the technical consequences of NSPS alternatives, policy implications concerning NSPS for steam-electric generators, and cost models for atmospheric and pressurized FBC systems. (LCL)

Bed slope effects on turbulent wave boundary layers: 2. Comparison with skewness, asymmetry, and other effects

DEFF Research Database (Denmark)

Fuhrman, David R.; Fredsøe, Jørgen; Sumer, B. Mutlu

2009-01-01

currents or undertow). The effects from each of the four components are isolated and quantified using a standard set of bed shear stress quantities, allowing their easy comparison. For conditions representing large shallow-water waves on steep slopes, the results suggest that converging-diverging effects......A numerical model solving incompressible Reynolds-averaged Navier-Stokes equations, combined with a two-equation k-omega model for turbulence closure, is used to systematically compare the relative strength of bed shear stress quantities and boundary layer streaming under wave motions from four...... from beach slope may make a significant onshore bed load contribution. Generally, however, the results suggest wave skewness (in addition to conventional steady streaming) as the most important onshore contribution outside the surf zone. Streaming induced within the wave boundary layer is also...

Bed care for patients in palliative settings: considering risks to caregivers and bed surfaces.

Science.gov (United States)

Fragala, Guy

2015-02-01

Ensuring patients are comfortable in bed is key to effective palliative care, but when moving and positioning patients in bed, health professionals face an occupational risk of injury. The turning and positioning (TAP) system is a new method of moving patients in bed, that evidence has shown to reduce the risk of injury to caregivers. Providing the correct bed surface is another aspect of bed care essential to the comfort of the palliative patient, and to aid wound prevention and treatment. It is important to take a patient-centred approach when considering the most appropriate bed surface patients. This article provides an overview and discussion of these two aspects of bed care for palliative patients.

Uranium bed oxidation vacuum process system

International Nuclear Information System (INIS)

McLeland, H.L.

1977-01-01

Deuterium and tritium gases are occluded in uranium powder for release into neutron generator tubes. The uranium powder is contained in stainless steel bottles, termed ''beds.'' If these beds become damaged, the gases must be removed and the uranium oxidized in order not to be flammable before shipment to ERDA disposal grounds. This paper describes the system and methods designed for the controlled degassing and oxidation process. The system utilizes sputter-ion, cryo-sorption and bellows pumps for removing the gases from the heated source bed. Removing the tritium gas is complicated by the shielding effect of helium-3, a byproduct of tritium decay. This effect is minimized by incremental pressure changes, or ''batch'' processing. To prevent runaway exothermic reaction, oxidation of the uranium bed is also done incrementally, or by ''batch'' processing, rather than by continuous flow. The paper discusses in detail the helium-3 shielding effect, leak checks that must be made during processing, bed oxidation, degree of gas depletion, purity of gases sorbed from beds, radioactivity of beds, bed disposal and system renovation

The effect of bed particle size and deposit morphology on the filtration of magnetite through granular graphite beds

International Nuclear Information System (INIS)

Barbieri, R.R.; Bercovich, E.J.; Liberman, S.J.

1980-01-01

Graphite filters are of great interest for water purification in nuclear power reactors' primary systems due to their possible operation at high temperature. The influence of the bed particle size on the retention of magnetite from aqueous suspensions at room temperature was studied. The filtration coefficient changes from 0.0 to 0.18 as the mean graphite particle diameter decreases from 1.2 to 0. mm. As the retention increases, there is also an increase in the differential pressure across the bed, so both effects must be considered in order to optimize filter's operation. The specific effective volume of the deposit was calculated with the Blake-Kozeny equation and the experimental specific volumes. These are much larger than the specific volume of solid magnetite. From the results, information regarding the morphology of the deposit in the filter is obtained. (M.E.L) [es

Effects of strict prolonged bed rest on cardiorespiratory fitness

DEFF Research Database (Denmark)

Ried-Larsen, Mathias; Aarts, Hugo M; Joyner, Michael J

2017-01-01

The aim of this systematic review and meta-analysis [International Prospective Register of Systematic Reviews (PROSPERO) CRD42017055619] was to assess the effects of strict prolonged bed rest (without countermeasures) on maximal oxygen uptake (V̇o2max) and to explore sources of variation therein....

Evaluation of a clay-based acidic bedding conditioner for dairy cattle bedding.

Science.gov (United States)

Proietto, R L; Hinckley, L S; Fox, L K; Andrew, S M

2013-02-01

This study investigated the effects of a clay-based acidic bedding conditioner on sawdust bedding pH, dry matter (DM), environmental pathogen counts, and environmental bacterial counts on teat ends of lactating dairy cows. Sixteen lactating Holstein cows were paired based on parity, days in milk, milk yield, and milk somatic cell count, and were negative for the presence of an intramammary pathogen. Within each pair, cows were randomly assigned to 1 of 2 treatments with 3-wk periods in a crossover design. Treatment groups consisted of 9 freestalls per group bedded with either untreated sawdust or sawdust with a clay-based acidic bedding conditioner, added at 3- to 4-d intervals over each 21-d period. Bedding and teat ends were aseptically sampled on d 0, 1, 2, 7, 14, and 21 for determination of environmental bacterial counts. At the same time points, bedding was sampled for DM and pH determination. The bacteria identified in the bedding material were total gram-negative bacteria, Streptococcus spp., and coliform bacteria. The bacteria identified on the teat ends were Streptococcus spp., coliform bacteria, and Klebsiella spp. Teat end score, milk somatic cell count, and intramammary pathogen presence were measured weekly. Bedding and teat cleanliness, environmental high and low temperatures, and dew point data were collected daily. The bedding conditioner reduced the pH, but not the DM, of the sawdust bedding compared with untreated sawdust. Overall environmental bacterial counts in bedding were lower for treated sawdust. Total bacterial counts in bedding and on teat ends increased with time over both periods. Compared with untreated sawdust, the treated bedding had lower counts of total gram-negative bacteria and streptococci, but not coliform counts. Teat end bacterial counts were lower for cows bedded on treated sawdust for streptococci, coliforms, and Klebsiella spp. compared with cows bedded on untreated sawdust. The clay-based acidic bedding conditioner

The effect of insecticide-treated bed net on malarial parasitaemia ...

African Journals Online (AJOL)

AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search ... nets sold by a social marketing project were used as the intervention group. ... Keywords: Insecticide-treated bed net, Effectiveness, Malaria control, South-South Nigeria.

Effects of turning on skin-bed interface pressures in healthy adults.

Science.gov (United States)

Peterson, Matthew J; Schwab, Wilhelm; van Oostrom, Johannes H; Gravenstein, Nikolaus; Caruso, Lawrence J

2010-07-01

This paper is a report of a study of the effects of lateral turning on skin-bed interface pressures in the sacral, trochanteric and buttock regions, and its effectiveness in unloading at-risk tissue. Minimizing skin-support surface interface pressure is important in pressure ulcer prevention, but the effect of standard patient repositioning on skin interface pressure has not been objectively established. Data were collected from 15 healthy adults from a university-affiliated hospital. Mapped 24-inch x 24-inch (2304 half-inch sensors) interface pressure profiles were obtained in the supine position, followed by lateral turning with pillow or wedge support and subsequent head-of-bed elevation to 30 degrees . Raising the head-of-bed to 30 degrees in the lateral position statistically significantly increased peak interface pressures and total area > or = 32 mmHg. Comparing areas > or = 32 mmHg from all positions, 93% of participants had skin areas with interface pressures > or = 32 mmHg throughout all positions (60 +/- 54 cm(2)), termed 'triple jeopardy areas'. The triple jeopardy area increased statistically significantly with wedges as compared to pillows (153 +/- 99 cm(2) vs. 48 +/- 47 cm(2), P turning by experienced intensive care unit nurses does not reliably unload all areas of high skin-bed interface pressures. These areas remain at risk for skin breakdown, and help to explain why pressure ulcers occur despite the implementation of standard preventive measures. Support materials for maintaining lateral turned positions can also influence tissue unloading and triple jeopardy areas.

Bacillus cereus in free-stall bedding.

Science.gov (United States)

Magnusson, M; Svensson, B; Kolstrup, C; Christiansson, A

2007-12-01

To increase the understanding of how different factors affect the bacterial growth in deep sawdust beds for dairy cattle, the microbiological status of Bacillus cereus and coliforms in deep sawdust-bedded free stalls was investigated over two 14-d periods on one farm. High counts of B. cereus and coliforms were found in the entire beds. On average, 4.1 log(10) B. cereus spores, 5.5 log(10) B. cereus, and 6.7 log(10) coliforms per gram of bedding could be found in the upper layers of the sawdust likely to be in contact with the cows' udders. The highest counts of B. cereus spores, B. cereus, and coliforms were found in the bedding before fresh bedding was added, and the lowest immediately afterwards. Different factors of importance for the growth of B. cereus in the bedding material were explored in laboratory tests. These were found to be the type of bedding, pH, and the type and availability of nutrients. Alternative bedding material such as peat and mixtures of peat and sawdust inhibited the bacterial growth of B. cereus. The extent of growth of B. cereus in the sawdust was increased in a dose-dependent manner by the availability of feces. Urine added to different bedding material raised the pH and also led to bacterial growth of B. cereus in the peat. In sawdust, a dry matter content greater than 70% was needed to lower the water activity to 0.95, which is needed to inhibit the growth of B. cereus. In an attempt to reduce the bacterial growth of B. cereus and coliforms in deep sawdust beds on the farm, the effect of giving bedding daily or a full replacement of the beds was studied. The spore count of B. cereus in the back part of the free stalls before fresh bedding was added was 0.9 log units lower in stalls given daily bedding than in stalls given bedding twice weekly. No effect on coliform counts was found. Replacement of the entire sawdust bedding had an effect for a short period, but by 1 to 2 mo after replacement, the counts of B. cereus spores in the

Model Studies on the Effectiveness of MBBR Reactors for the Restoration of Small Water Reservoirs

Science.gov (United States)

Nowak, Agata; Mazur, Robert; Panek, Ewa; Chmist, Joanna

2018-02-01

The authors present the Moving Bed Biofilm Reactor (MBBR) model with a quasi-continuous flow for small water reservoir restoration, characterized by high concentrations of organic pollutants. To determine the efficiency of wastewater treatment the laboratory analysis of physic-chemical parameters were conducted for the model on a semi-technical scale of 1:3. Wastewater treatment process was carried out in 24 h for 1 m3 for raw sewage. The startup period was 2 weeks for all biofilters (biological beds). Approximately 50% reduction in COD and BOD5 was obtained on average for the studied bioreactors. Significant improvements were achieved in theclarity of the treated wastewater, with the reduction of suspension by 60%. The oxygen profile has improved significantly in 7 to 9 hours of the process, and a diametric reduction in the oxidative reduction potential was recorded. A preliminary model of biological treatment effectiveness was determined based on the conducted studies. In final stages, the operation mode was set in real conditions of polluted water reservoirs.

Thermal Analysis of Fluidized Bed and Fixed Bed Latent Heat Thermal Storage System

Science.gov (United States)

Beemkumar, N.; Karthikeyan, A.; Shiva Keshava Reddy, Kota; Rajesh, Kona; Anderson, A.

2017-05-01

Thermal energy storage technology is essential because its stores available energy at low cost. Objective of the work is to store the thermal energy in a most efficient method. This work is deal with thermal analysis of fluidized bed and fixed bed latent heat thermal storage (LHTS) system with different encapsulation materials (aluminium, brass and copper). D-Mannitol has been used as phase change material (PCM). Encapsulation material which is in orbicular shape with 4 inch diameter and 2 mm thickness orbicular shaped product is used. Therminol-66 is used as a heat transfer fluid (HTF). Arrangement of encapsulation material is done in two ways namely fluidized bed and fixed bed thermal storage system. Comparison was made between the performance of fixed bed and fluidized bed with different encapsulation material. It is observed that from the economical point of view aluminium in fluidized bed LHTS System has highest efficiency than copper and brass. The thermal energy storage system can be analyzed with fixed bed by varying mass flow rate of oil paves a way to find effective heat energy transfer.

The effect of tapering on a magnetocaloric regenerator bed

DEFF Research Database (Denmark)

Dallolio, Stefano; Lei, Tian; Engelbrecht, Kurt

2017-01-01

. Therefore, this paper investigates the effect of the tapering of the regenerators, which exhibit better air-gap utilization. Several simulations using a 1D AMR model were run to study the performance of the tapered regenerator, and the results were compared to the case of the straight regenerator bed...

Effect of friction on pebble flow pattern in pebble bed reactor

International Nuclear Information System (INIS)

Li, Yu; Gui, Nan; Yang, Xingtuan; Tu, Jiyuan; Jiang, Shengyao

2016-01-01

Highlights: • A 3D DEM study on particle–wall/particle friction in pebble bed reactor is carried out. • Characteristic values are defined to evaluate features of pebble flow pattern quantitatively. • Particle–wall friction is dominant to determine flow pattern in a specific pebble bed. • Friction effect of hopper part on flow field is more critical than that of cylinder part. • Three cases of 1:1 full scale practical pebble beds are simulated for demonstration. - Abstract: Friction affects pebble flow pattern in pebble-bed high temperature gas-cooled reactor (HTGR) significantly. Through a series of three dimensional DEM (discrete element method) simulations it is shown that reducing friction can be beneficial and create a uniform and consistent flow field required by nuclear engineering. Particle–wall friction poses a decisive impact on flow pattern, and particle–particle friction usually plays a secondary role; relation between particle–wall friction and flow pattern transition is also concluded. Moreover, new criteria are created to describe flow patterns quantitatively according to crucial issues in HTGR like stagnant zone, radial uniformity and flow sequence. Last but not least, it is proved that friction control of hopper part is more important than that of cylinder part in practical pebble beds, so reducing friction between pebbles and hopper surface is the engineering priority.

Effects of sawdust bedding dry matter on lying behavior of dairy cows: a dose-dependent response.

Science.gov (United States)

Reich, L J; Weary, D M; Veira, D M; von Keyserlingk, M A G

2010-04-01

The objective was to determine the effect of sawdust bedding dry matter on the lying behavior of Holstein cows. Dry matter (DM) was varied systematically over 5 treatment levels to test how cows respond to damp bedding. This experiment was repeated during summer and winter to test if the effects of damp bedding varied with season. The 5 bedding treatments averaged (+/-SD) 89.8+/-3.7, 74.2+/-6.4, 62.2+/-6.3, 43.9+/-4.0, and 34.7+/-3.8% DM. Over the course of the trial, minimum and maximum temperatures in the barn were 2.6+/-2.0 and 6.8+/-2.2 degrees C in the winter and 13.3+/-2.5 and 22.6+/-4.1 degrees C in the summer. In both seasons, 5 groups of 3 nonlactating cows were housed in free stalls bedded with sawdust. Following a 5-d acclimation period on dry bedding, groups were exposed to the 5 bedding treatments in a 5 x 5 Latin square. Each treatment lasted 4 d, followed by 1 d when the cows were provided with dry bedding. Stall usage was assessed by 24-h video scanned at 5-min intervals. Responses were analyzed within group (n=5) as the observational unit. Bedding DM affected lying time, averaging 10.4+/-0.4 h/d on the wettest treatment and increasing to 11.5+/-0.4 h/d on the driest bedding. Lying time varied with season, averaging 12.1+/-0.4 h/d across treatments during the winter and 9.9+/-0.6 h/d during the summer, but season and bedding DM did not interact. These results indicate that access to dry bedding is important for dairy cows. Copyright (c) 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Removal of odorous materials in carbonization process of dyeing wastewater sludge

International Nuclear Information System (INIS)

Bae, Sung-Keun; Woo, Byung-Kyu; Nam, In-Sick; Lee, Joo-Yong; Kim, Gi-Sun

2010-01-01

From drying process in a carbonization facility of dyeing wastewater sludge, noxious and odorous materials such as NH 3 , H 2 S, and Volatile Organic Compound (VOCs) contained in the sludge are emitted. In previous studies Regenerative Thermal Oxidizer (RTO) was verified as the most efficient method to eliminate them; nevertheless, it was very expensive to establish and operate because of fuel consumption. To estimate the feasibility of a water spray tower and bio-filter system, laboratory scale experiments for NH 3 , H 2 S, and toluene gas carried out. In case of water spray experiment for the single gas, the removal rate of NH 3 and H 2 S increased as decreasing the concentration, increasing the liquid/ gas ratio, and increasing the retention time. Toluene was eliminated as low as 20% regardless of the above operating parameters. The removal rates of NH 3 and H 2 S were 88∼98% and 80∼83%, respectively. For the mixed gas, the removal rates of NH 3 and toluene was a little dropped, but H 2 S was eliminated slightly more as compared with single gas experiment. Water spray system was not effective for toluene, but it was removed over 90% in bio-filter system. Retention time of gas in bio-filter bed might be an important operating parameter and its optimal condition was considered to 60 seconds. It is experimentally verified that odorous material was very effectively removed by a water spray tower and bio-filter combined system. (author)

Experimental investigation of multidimensional cooling effects on the coolability of a debris bed

International Nuclear Information System (INIS)

Rashidi, M.; Kulenovici, R.; Laurieni, E.

2011-01-01

During a severe accident in a light water reactor, the core can melt and be relocated to the lower plenum of the reactor pressure vessel. There it can form a particulate debris bed due to the possible presence of water. Within the reactor safety research, the removal of decay heat from a debris bed (formed from corium and residual water) is of great importance. In order to investigate experimentally the long-term coolability of debris beds, the down-scaled non nuclear test facility DEBRIS has been established at IKE. The major objectives of the experimental investigations at this test facility are the determination of local pressure drops for steady state boiling to check friction laws, the determination of dryout heat fluxes under various conditions for validation of numerical models, and the analysis of quenching processes of dry hot debris beds. A large number of 1D-experiments were carried out to investigate the coolability limits for different bed configurations at various thermohydraulic conditions, and to validate numerical models which can be used in reactor safety studies. Analyses based on one-dimensional configurations underestimate the coolability in realistic multidimensional configurations, where lateral water access and water inflow via bottom regions are favored. This paper presents 2D experimental results, based on various kinds of water inflow conditions into the bed, boiling and dryout tests with different bed configurations and different system pressures. Preliminary results show that the system pressure has no significant effect on the fundamental shape of the pressure gradient inside the bed, whereas with increasing system pressure the coolability limits are increased

Visualization of bed material movement in a simulated fluidized bed heat exchanger by neutron radiography

International Nuclear Information System (INIS)

Umekawa, Hisashi; Ozawa, Mamoru; Takenaka, Nobuyuki; Matsubayashi, Masahito

1999-01-01

The bulk movement of fluidized bed material was visualized by neutron radiography by introducing tracers into the bed materials. The simulated fluidized bed consisted of aluminum plates, and the bed material was sand of 99.7% SiO 2 (mean diameter: 0.218 mm, density: 2555 kg/m 3 ). Both materials were almost transparent to neutrons. Then the sand was colored by the contamination of the sand coated by CdSO 4 . Tracer particles of about 2 mm diameter were made by the B 4 C, bonded by the vinyl resin. The tracer was about ten times as large as the particle of fluidized bed material, but the traceability was enough to observe the bed-material bulk movement owing to the large effective viscosity of the fluidized bed. The visualized images indicated that the bubbles and/or wakes were important mechanism of the behavior of the fluidized bed movement

Removal of nitrogen from anaerobically digested swine wastewater ...

African Journals Online (AJOL)

This result indicates that the sulfur-packed biofilter would be used as an efficient option for denitrification by autotrophic denitrifiers during swine wastewater treatment. Key words: Biological nitrogen removal, nitrification, denitrification, chemical oxygen demand (COD), intermittent aeration, sulfur-packed bed reactor, swine ...

Entomological determinants of insecticide-treated bed net effectiveness in Western Myanmar

NARCIS (Netherlands)

Smithuis, Frank M.; Kyaw, Moe Kyaw; Phe, U. Ohn; van der Broek, Ingrid; Katterman, Nina; Rogers, Colin; Almeida, Patrick; Kager, Piet A.; Stepniewska, Kasia; Lubell, Yoel; Simpson, Julie A.; White, Nicholas J.

2013-01-01

In a large cluster randomized control trial of insecticide-treated bed nets (ITN) in Western Myanmar the malaria protective effect of ITN was found to be highly variable and, in aggregate, the effect was not statistically significant. A coincident entomological investigation measured malaria vector

Effects of high salinity wastewater on methanogenic sludge bed systems

NARCIS (Netherlands)

Ismail, S.; Gonzalez-Contreras, P.A.; Jeison, D.A.; Lier, van J.B.

2008-01-01

The attainable loading potentials of anaerobic sludge bed systems are strongly dependent on the growth of granular biomass with a particular wastewater. Experiments were conducted to determine the effects of high salinity wastewater on the biological and physical properties of methanogenic sludge.

Biofilm Effect on Flow Structure over a Permeable Bed

Science.gov (United States)

Kazemifar, F.; Blois, G.; Aybar, M.; Perez-Calleja, P.; Nerenberg, R.; Sinha, S.; Hardy, R. J.; Best, J.; Sambrook Smith, G.; Christensen, K. T.

2017-12-01

Biofilms constitute an important form of bacterial life in aquatic environments and are present at the fluid-solid interfaces in natural and industrial settings, such as water distribution systems and riverbeds among others. The permeable, heterogeneous, and deformable structure of biofilms can influence mass and momentum transport between the subsurface and freestream. However, this interaction is not fully understood, in part due to technical obstacles impeding quantitative experimental investigations. In this work, the effect of biofilm on flow structure over a permeable bed is studied. Experiments are conducted in a closed water channel equipped with an idealized two-dimensional permeable bed. Prior to conducting flow experiments, the models are placed within an independent recirculating reactor for biofilm growth. Once a targeted biofilm growth stage is achieved, the models are transferred to the water channel and subjected to transitional and turbulent flows. Long-distance microscopic particle image velocimetry measurements are performed to quantify the effect of biofilm on the turbulence structure of the free flow as well as the freestream-subsurface flow interaction.

Long-Duration Space Flight and Bed Rest Effects on Testosterone and Other Steroids

Science.gov (United States)

Heer, Martina; Wang, Zuwei; Huntoon, Carolyn L.; Zwart, Sara R.

2012-01-01

Context: Limited data suggest that testosterone is decreased during space flight, which could contribute to bone and muscle loss. Objective: The main objective was to assess testosterone and hormone status in long- and short-duration space flight and bed rest environments and to determine relationships with other physiological systems, including bone and muscle. Design: Blood and urine samples were collected before, during, and after long-duration space flight. Samples were also collected before and after 12- to 14-d missions and from participants in 30- to 90-d bed rest studies. Setting: Space flight studies were conducted on the International Space Station and before and after Space Shuttle missions. Bed rest studies were conducted in a clinical research center setting. Data from Skylab missions are also presented. Participants: All of the participants were male, and they included 15 long-duration and nine short-duration mission crew members and 30 bed rest subjects. Main Outcome Measures: Serum total, free, and bioavailable testosterone were measured along with serum and urinary cortisol, serum dehydroepiandrosterone, dehydroepiandrosterone sulfate, and SHBG. Results: Total, free, and bioavailable testosterone was not changed during long-duration space flight but were decreased (P space flight. There were no changes in other hormones measured. Testosterone concentrations dropped before and soon after bed rest, but bed rest itself had no effect on testosterone. Conclusions: There was no evidence for decrements in testosterone during long-duration space flight or bed rest. PMID:22049169

Using multiple bed load measurements: Toward the identification of bed dilation and contraction in gravel-bed rivers

Science.gov (United States)

Marquis, G. A.; Roy, A. G.

2012-02-01

This study examines bed load transport processes in a small gravel-bed river (Béard Creek, Québec) using three complementary methods: bed elevation changes between successive floods, bed activity surveys using tags inserted into the bed, and bed load transport rates from bed load traps. The analysis of 20 flood events capable of mobilizing bed material led to the identification of divergent results among the methods. In particular, bed elevation changes were not consistent with the bed activity surveys. In many cases, bed elevation changes were significant (1 to 2 times the D50) even if the bed surface had not been activated during the flood, leading to the identification of processes of bed dilation and contraction that occurred over 10% to 40% of the bed surface. These dynamics of the river bed prevent accurate derivation of bed load transport rates from topographic changes, especially for low magnitude floods. This paper discusses the mechanisms that could explain the dilation and contraction of particles within the bed and their implications in fluvial dynamics. Bed contraction seems to be the result of the winnowing of the fine sediments under very low gravel transport. Bed dilation seems to occur on patches of the bed at the threshold of motion where various processes such as fine sediment infiltration lead to the maintenance of a larger sediment framework volume. Both processes are also influenced by flood history and the initial local bed state and in turn may have a significant impact on sediment transport and morphological changes in gravel-bed rivers.

Abatement of styrene waste gas emission by biofilter and biotrickling filter: comparison of packing materials and inoculation procedures.

Science.gov (United States)

Pérez, M C; Álvarez-Hornos, F J; Portune, K; Gabaldón, C

2015-01-01

The removal of styrene was studied using two biofilters packed with peat and coconut fibre (BF1-P and BF2-C, respectively) and one biotrickling filter (BTF) packed with plastic rings. Two inoculation procedures were applied: an enriched culture with strain Pseudomonas putida CECT 324 for BFs and activated sludge from a municipal wastewater treatment plant for the BTF. Inlet loads (ILs) between 10 and 45 g m(-3) h(-1) and empty bed residence times (EBRTs) from 30 to 120 s were applied. At inlet concentrations ranging between 200 and 400 mg Nm(-3), removal efficiencies between 70 % and 95 % were obtained in the three bioreactors. Maximum elimination capacities (ECs) of 81 and 39 g m(-3) h(-1) were obtained for the BF1-P and BF2-C, respectively (IL of 173 g m(-3) h(-1) and EBRT of 60 s in BF1-P; IL of 89 g m(-3) h(-1) and EBRT of 90 s in BF2-C). A maximum EC of 52 g m(-3) h(-1) was obtained for the BTF (IL of 116 g m(-3) h(-1), EBRT of 45 s). Problems regarding high pressure drop appeared in the peat BF, whereas drying episodes occurred in the coconut fibre BF. DGGE revealed that the pure culture used for BF inoculation was not detected by day 105. Although two different inoculation procedures were applied, similar styrene removal at the end of the experiments was observed. The use as inoculum of activated sludge from municipal wastewater treatment plant appears a more feasible option.

Application of a model to investigate the effective thermal conductivity of randomly packed fusion pebble beds

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiaoliang; Zheng, Jie; Chen, Hongli, E-mail: hlchen1@ustc.edu.cn

2016-05-15

In our precious study, a prediction model, which calculates the effective thermal conductivity k{sub eff} of mono-sized pebble beds, has been developed and validated. Based on this model, here the effects of these influencing factors such as pebble size, thermal radiation, contact area, filling gas, gas flow, gas pressure, etc. on the k{sub eff} of randomly packed fusion pebble beds are studied and analyzed. The pebble beds investigated include Li{sub 4}SiO{sub 4}, Li{sub 2}ZrO{sub 3}, Li{sub 2}TiO{sub 3}, Li{sub 2}O, Be and BeO pebble beds. In the current study, many important and meaningful conclusions are derived and some of them are similar to the existing research results. Particularly, some critters that under which conditions the effect of some influencing factors can be neglected or should be considered are also presented.

Investigation of effective thermal conductivity for pebble beds by one-way coupled CFD-DEM method for CFETR WCCB

Energy Technology Data Exchange (ETDEWEB)

Chen, Lei [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei, Anhui 230027 (China); Chen, Youhua [University of Science and Technology of China, Hefei, Anhui 230027 (China); Huang, Kai [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Liu, Songlin, E-mail: slliu@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei, Anhui 230027 (China)

2016-05-15

Highlights: • A CFD-DEM coupled numerical model is built based on the prototypical blanket pebble bed. • The numerical model can be applied to simulate heat transfer of a pebble bed and estimate effective thermal conductivity. • The numerical model agrees well with the theoretical SZB model. • Effective thermal conductivity of pebble beds for WCCB is estimated by the current model. - Abstract: The mono-sized beryllium pebble bed and the multi-sized Li{sub 2}TiO{sub 3}/Be{sub 12}Ti mixed pebble bed are the main schemes for the Water-cooled ceramic breeder blanket (WCCB) of China Fusion Engineering Test Reactor (CFETR). And the effective thermal conductivity (k{sub eff}) of the pebble beds is important to characterize the thermal performance of WCCB. In this study, a one-way coupled CFD-DEM method was employed to simulate heat transfer and estimate k{sub eff}. The geometric topology of a prototypical blanket pebble bed was produced by the discrete element method (DEM). Based on the geometric topology, the temperature distribution and the k{sub eff} were obtained by the computational fluid dynamics (CFD) analysis. The current numerical model presented a good performance to calculate k{sub eff} of the beryllium pebble bed, and according to the modeling of the Li{sub 2}TiO{sub 3}/Be{sub 12}Ti mixed pebble bed, k{sub eff} was estimated with values ranged between 2.0 and 4.0 W/(m∙K).

Multi-sphere unit cell model to calculate the effective thermal conductivity in pebble bed reactors

International Nuclear Information System (INIS)

Van Antwerpen, W.; Rousseau, P.G.; Du Toit, C.G.

2010-01-01

A proper understanding of the mechanisms of heat transfer, fluid flow and pressure drop through a packed bed of spheres is of utmost importance in the design of a high temperature Pebble Bed Reactor (PBR). While the gas flows predominantly in the axial direction through the bed, the total effective thermal conductivity is a lumped parameter that characterises the total heat transfer in the radial direction through the packed bed. The study of the effective thermal conductivity is important because it forms an intricate part of the self-acting decay heat removal chain, which is directly related to the PBR safety case. The effective thermal conductivity is the summation of various heat transport phenomena. These are the enhanced thermal conductivity due to turbulent mixing as the fluid passes through the voids between pebbles, heat transfer due to the movement of the solid spheres and thermal conduction and thermal radiation between the spheres in a stagnant fluid environment. In this study, the conduction and radiation between the spheres are investigated. Firstly, existing correlations for the effective thermal conductivity are investigated, with particular attention given to its applicability in the near-wall region. Several phenomena in particular are examined namely: conduction through the spheres, conduction through the contact area between the spheres, conduction through the gas phase and radiation between solid surfaces. A new approach to simulate the effective thermal conductivity for randomly packed beds is then presented, namely the so-called Multi-sphere Unit Cell Model. The model is validated by comparing the results with that obtained in experiments. (authors)

Removal of Heavy Metals from Synthesis Industrial Wastewater Using Local Isolated Candida Utilis and Aspergillus Niger as Bio-Filter

OpenAIRE

Safaa Abd Alrasool Ali

2013-01-01

In this study biomass filter of Candida Utilis which isolated from food sample in Baghdad local market and Aspergillus Niger which isolated from Baghdad soil used to biosorption heavy metals from synthesis industrial wastewater. two bio-filters were designed as cylindrical Perspex with height 10cm, diameter 3cm as a shell and inside their are layers of Sponge were prepare as the size of diameter of the cylindrical filter with thickness of 2cm arrange inside it, biomass production were 6 g of ...

Effects of bedding systems selected by manual muscle testing on sleep and sleep-related respiratory disturbances.

Science.gov (United States)

Tsai, Ling-Ling; Liu, Hau-Min

2008-03-01

In this study, we investigated the feasibility of applying manual muscle testing (MMT) for bedding selection and examined the bedding effect on sleep. Four lay testers with limited training in MMT performed muscle tests for the selection of the bedding systems from five different mattresses and eight different pillows for 14 participants with mild sleep-related respiratory disturbances. For each participant individually, two bedding systems-one inducing stronger muscle forces and the other inducing weaker forces-were selected. The tester-participant pairs showed 85% and 100% agreement, respectively, for the selection of mattresses and pillows that induced the strongest muscle forces. The firmness of the mattress and the height of the pillow were significantly correlated with the body weight and body mass index of the participants for the selected strong bedding system but not for the weak bedding system. Finally, differences were observed between the strong and the weak bedding systems with regard to sleep-related respiratory disturbances and the percentage of slow-wave sleep. It was concluded that MMT can be performed by inexperienced testers for the selection of bedding systems.

Study on effective particle diameters and coolability of particulate beds packed with irregular multi-size particles

Energy Technology Data Exchange (ETDEWEB)

Thakre, S.; Ma, W.; Kudinov, P.; Bechta, S. [Royal Institute of Technology, KTH. Div. of Nuclear Power Safety, Stockholm (Sweden)

2013-08-15

One of the key questions in severe accident research is the coolability of the debris bed, i.e., whether decay heat can be completely removed by the coolant flow into the debris bed. Extensive experimental and analytical work has been done to substantiate the coolability research. Most of the available experimental data is related to the beds packed with single size (mostly spherical) particles, and less data is available for multi-size/irregular-shape particles. There are several analytical models available, which rely on the mean particle diameter and porosity of the bed in their predictions. Two different types of particles were used to investigate coolability of particulate beds at VTT, Finland. The first type is irregular-shape Aluminum Oxide gravel particles whose sizes vary from 0.25 mm to 10 mm, which were employed in the STYX experiment programme (2001-2008). The second type is spherical beads of Zirconium silicate whose sizes vary between 0.8 mm to 1 mm, which were used in the COOLOCE tests (Takasuo et al., 2012) to study the effect of multi-dimensional flooding on coolability. In the present work, the two types of particles are used in the POMECO-FL and POMECO-HT test facility to obtain their effective particle diameters and dryout heat flux of the beds, respectively. The main idea is to check how the heaters' orientations (vertical in COOLOCE vs. horizontal in POMECO-HT) and diameters (6 mm in COOLOCE vs. 3 mm in POMECO-HT) affect the coolability (dryout heat flux) of the test beds. The tests carried out on the POMECO-FL facility using a bed packed with aluminum oxide gravel particles show the effective particle diameter of the gravel particles is 0.65 mm, by which the frictional pressure gradient can be predicted by the Ergun equation. After the water superficial velocity is higher than 0.0025 m/s, the pressure gradient is underestimated. The effective particle diameter of the zirconium particles is found as 0.8 mm. The dryout heat flux is measured on

Study on effective particle diameters and coolability of particulate beds packed with irregular multi-size particles

International Nuclear Information System (INIS)

Thakre, S.; Ma, W.; Kudinov, P.; Bechta, S.

2013-08-01

One of the key questions in severe accident research is the coolability of the debris bed, i.e., whether decay heat can be completely removed by the coolant flow into the debris bed. Extensive experimental and analytical work has been done to substantiate the coolability research. Most of the available experimental data is related to the beds packed with single size (mostly spherical) particles, and less data is available for multi-size/irregular-shape particles. There are several analytical models available, which rely on the mean particle diameter and porosity of the bed in their predictions. Two different types of particles were used to investigate coolability of particulate beds at VTT, Finland. The first type is irregular-shape Aluminum Oxide gravel particles whose sizes vary from 0.25 mm to 10 mm, which were employed in the STYX experiment programme (2001-2008). The second type is spherical beads of Zirconium silicate whose sizes vary between 0.8 mm to 1 mm, which were used in the COOLOCE tests (Takasuo et al., 2012) to study the effect of multi-dimensional flooding on coolability. In the present work, the two types of particles are used in the POMECO-FL and POMECO-HT test facility to obtain their effective particle diameters and dryout heat flux of the beds, respectively. The main idea is to check how the heaters' orientations (vertical in COOLOCE vs. horizontal in POMECO-HT) and diameters (6 mm in COOLOCE vs. 3 mm in POMECO-HT) affect the coolability (dryout heat flux) of the test beds. The tests carried out on the POMECO-FL facility using a bed packed with aluminum oxide gravel particles show the effective particle diameter of the gravel particles is 0.65 mm, by which the frictional pressure gradient can be predicted by the Ergun equation. After the water superficial velocity is higher than 0.0025 m/s, the pressure gradient is underestimated. The effective particle diameter of the zirconium particles is found as 0.8 mm. The dryout heat flux is measured on

EPA-Registered Bed Bug Products

Science.gov (United States)

... rest or hide in hampers, bed frames, even furniture); Failing to treat adjacent areas where bed bugs ... to work (some pesticides, such as desiccators or growth regulators, may be very effective but take some ...

Better backs by better beds?

DEFF Research Database (Denmark)

Bergholdt, Kim; Fabricius, Rasmus N; Bendix, Tom

2008-01-01

mattresses have a positive effect on LBP, and especially a hard mattress is commonly believed to have a positive effect. METHODS: One hundred sixty CLBP patients were randomized to 1 of 3 groups, having a mattress/bed mounted in their sleeping room for 1 month. The beds were: (1) waterbed (Akva), (2) body......-conforming foam mattress (Tempur), and (3) a hard mattress (Innovation Futon). At baseline and after 4 weeks, a blinded observer interviewed the patients on LBP levels (0-10), daily function (activities of daily living, 0-30), and on the amount of sleeping hours/night. RESULTS: Because of dropout of 19 patients...... using the probably most relevant "worst case" data. There were no relevant difference between the effects of the water bed and the foam bed. CONCLUSION: The Waterbed and foam mattress' did influence back symptoms, function and sleep more positively as apposed to the hard mattress, but the differences...

Daily micro particle distribution of an experimental recirculating aquaculture system – A case study

DEFF Research Database (Denmark)

Fernandes, Paulo; Pedersen, Lars-Flemming; Pedersen, Per Bovbjerg

2014-01-01

The particle size distribution (PSD) in a recirculating aquaculture system (RAS) was investigated duringa 24-h cycle. PSD was analyzed in water sampled at several locations in a recirculation loop containing a60-m drum filter, a submerged fixed-bed biofilter and a trickling filter.In relation...

Effectiveness of two different HDR brachytherapy regimens with the same BED value in cervical cancer

Directory of Open Access Journals (Sweden)

Rajesh Vashistha

2010-07-01

Full Text Available Purpose: To analyze the effectiveness of biologically effective dose (BED in two different regimens of HDR brachytherapy keeping the same total BED to point A and to compare the relationship of overall treatment time in terms of local control and bladder and rectal complications.Material and methods: The study included two groups comprising a total of 90 cervical cancer patients who underwent external beam radiotherapy (EBRT followed by HDR intracavitary brachytherapy (ICBT. EBRT treatment was delivered by a Co-60 teletherapy unit to a prescribed dose of 45 Gy with 1.8 Gy per fraction in 25 fractions over a period of five weeks. Parallel opposed anterior–posterior (AP/PA fields with no central shielding were used, followed by the HDR ICBT dose, to point A, of either two fractions of 9.5 Gy with a gap of 10 days, or three fractions of 7.5 Gy with a gap of 7 days between the fractions. Gemcitabine (dose of 150 mg/m2 was given weekly to all the patients as a radiosensitizer. The calculate BED3 to point A was almost the same in both groups to keep the same late complication rates. The doses, and BED10 and BED3, were calculated at different bladder and rectal point as well as at the lymphatictrapezoid points. During and after treatment patients were evaluated for local control and complications for 24 months.Results and Conclusions: Doses and BEDs at different bladder, rectal and lymphatic trapezoid points, local control, and complications in both HDR ICBT groups did not have statistically significant differences (p > 0.05. Both HDR ICBT schedules are well tolerable and equally effective.

Accounting for porous structure in effective thermal conductivity calculations in a pebble bed reactor

International Nuclear Information System (INIS)

Antwerpen, W. van; Rousseau, P.G.; Toit, C.G. du

2009-01-01

A proper understanding of the mechanisms of heat transfer, flow and pressure drop through a packed bed of spheres is of utmost importance in the design of a high temperature pebble bed reactor. A thorough knowledge of the porous structure within the packed bed is important to any rigorous analysis of the transport phenomena, as all the heat and flow mechanisms are influenced by the porous structure. In this paper a new approach is proposed to simulate the effective thermal conductivity employing a combination of new and existing correlations for randomly packed beds. More attention is given to packing structure based on coordination number and contact angles, resulting in a more rigorous differentiation between the bulk and near-wall regions. The model accounts for solid conduction, gas conduction, contact area, surface roughness as well as radiation. (author)

Apparatus comprising trace element dosage and method for treating raw water in biofilter

DEFF Research Database (Denmark)

2015-01-01

the inlet (2) to the outlet (3) or in the reverse direction, - the trace element dosage device (13) is positioned upstream of the porous filter material and microbial biomass and is configured to dose trace element(s) to the water flowing through the filter. A method for treating raw water by microbial......Apparatus for treating raw water in a biofilter The present invention relates to an apparatus in which raw water is treated through microbial activity where microbial activity is controlled by nutrients and other parameters. Some of the nutrients controlling the microbial activity are trace...... elements such as certain metals (Cu, Co, Cr, Mo, Ni, W, Zn or a mixture thereof). The apparatus comprising - a volume provided with an inlet (2) for raw water and an outlet (3) for water having been subjected to microbial activity, a filter and a trace element dosage device (13) are placed in this volume...

Experimental investigation of filled bed effect on the thermal performance of a wet cooling tower by using ZnO/water nanofluid

International Nuclear Information System (INIS)

Imani-Mofrad, Peyman; Saeed, Zeinali Heris; Shanbedi, Mehdi

2016-01-01

Highlights: • Effect of filled bed on performance of cooling tower with ZnO nanofluid evaluated. • Applying metal reticular bed is the best choice when ZnO/water nanofluid is used. • Metal reticular bed showed lowest fouling and agglomeration of nanoparticles. • Nanofluid improved cooling range, characteristic & effectiveness of cooling tower. - Abstract: This study deals with an experimental investigation on the effect of different types of filled beds on the thermal performance of a wet cooling tower by using zinc oxide (ZnO)/water nanofluid. Different concentrations of ZnO/water nanofluid were prepared through two-step procedure by using pure water with electrical conductivity of 2 μS/cm. First, by using ZnO/water nanofluid (0.08 wt%), effect of six different filled beds were investigated on the thermal performance of the cooling tower. Moreover, after each experiment the applied filled bed was reviewed in order to observe any aggregation or settlement of nanoparticles on the surfaces of the bed. It was found that applying metal reticular bed (Bed 1) is the best choice when ZnO/water nanofluid is used. In the other word Bed 1 results better thermal characteristics for cooling tower and less settlement of nanofluids. Then different concentrations of ZnO/water nanofluid in the range of 0.02–0.1 wt% is employed in the cooling tower by utilizing Bed 1. The results showed that by using nanofluids, cooling range, tower characteristic (TC) and effectiveness of cooling tower are enriched compared to water. For example, TC enhanced by 21.5% and 22.5% for ZnO/water nanofluid with concentration of 0.02 wt% and 0.05 wt%, respectively.

Effect of a flow-corrective insert on the flow pattern in a pebble bed reactor

Energy Technology Data Exchange (ETDEWEB)

Li, Yu; Gui, Nan; Yang, Xingtuan [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Tsinghua University, Beijing 100084 (China); Tu, Jiyuan [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Tsinghua University, Beijing 100084 (China); School of Aerospace, Mechanical & Manufacturing Engineering, RMIT University, Melbourne 3083, VIC (Australia); Jiang, Shengyao, E-mail: shengyaojiang@sina.com [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Tsinghua University, Beijing 100084 (China)

2016-04-15

Highlights: • Effect of an insert on improving flow uniformity and eliminating stagnant zone is studied. • Three values concerned with the stagnant zone, radial uniformity and flow sequence are used. • Outlet diameter is a critical parameter that determines balancing mechanism of the insert. • Height/location is varied to let the insert work in unbalanced region and avoid adverse effect. - Abstract: A flow-corrective insert is adopted in the pebble-bed high temperature gas-cooled reactor (HTGR) to improve flow performance of the pebble flow for the first time. 3D discrete element method (DEM) modeling is employed to study this slow and dense granular flow. It is verified that locating a properly designed insert in the bed can help transform unsatisfactory flow field to the preferred flow pattern for pebble bed reactors. Three characteristic values on the stagnant zone, radial uniformity and flow sequence of pebble flow are defined to evaluate uniformity of the overall flow field quantitatively. The results demonstrate that the pebble bed equipped with an insert performs better than normal beds from all these three aspects. Moreover, based on numerical experiments, several universal tips for insert design on height, location and outlet diameter are suggested.

Microbial community response reveals underlying mechanism of industrial-scale manganese sand biofilters used for the simultaneous removal of iron, manganese and ammonia from groundwater.

Science.gov (United States)

Zhang, Yu; Sun, Rui; Zhou, Aijuan; Zhang, Jiaguang; Luan, Yunbo; Jia, Jianna; Yue, Xiuping; Zhang, Jie

2018-01-08

Most studies have employed aeration-biofiltration process for the simultaneous removal of iron, manganese and ammonia in groundwater. However, what's inside the "black box", i.e., the potential contribution of functional microorganisms behavior and interactions have seldom been investigated. Moreover, little attention has been paid to the correlations between environmental variables and functional microorganisms. In this study, the performance of industrial-scale biofilters for the contaminated groundwater treatment was studied. The effluent were all far below the permitted concentration level in the current drinking water standard. Pyrosequencing illustrated that shifts in microbial community structure were observed in the microbial samples from different depths of filter. Microbial networks showed that the microbial community structure in the middle- and deep-layer samples was similar, in which a wide range of manganese-oxidizing bacteria was identified. By contrast, canonical correlation analysis showed that the bacteria capable of ammonia-oxidizing and nitrification was enriched in the upper-layer, i.e., Propionibacterium, Nitrosomonas, Nitrosomonas and Candidatus Nitrotoga. The stable biofilm on the biofilter media, created by certain microorganisms from the groundwater microflora, played a crucial role in the simultaneous removal of the three pollutants.

Utility of Recycled Bedding for Laboratory Rodents

OpenAIRE

Miyamoto, Toru; Li, Zhixia; Kibushi, Tomomi; Okano, Shinya; Yamasaki, Nakamichi; Kasai, Noriyuki

2009-01-01

Animal facilities generate a large amount of used bedding containing excrement as medical waste. We developed a recycling system for used bedding that involves soft hydrothermal processing. In this study, we examined the effects of bedding type on growth, hematologic and serum biochemical values, and organ weights of female and male mice reared on either recycled or fresh bedding from 3 to 33 wk of age. Neither growth nor physiology differed between mice housed on recycled bedding compared wi...

The effectiveness of bed bathing practices on skin integrity and hospital-acquired infections among adult patients

DEFF Research Database (Denmark)

Veje, Pia; Larsen, Palle

2014-01-01

is: What is the effectiveness of traditional towel bed bath practice compared to other innovate bed bath practices on maintaining skin integrity, skin barrier function and reduction of pathogen microbial counts on skin among adult patients in all settings? Inclusion criteria: Types of participants...... practices, including all bag bath interventions, not limited to any specific type or brand. For the purpose of this systematic review, bag bath interventions include bathing patients with pre-packaged disposal washcloths by use of a different cloth to wash each part of the patient's body. The washcloths...... typically comprise rayon/polyester cloth pre-moistened with an evaporating no-rinse cleanser and emollients. Comparator: The comparator is the traditional bed bath (towel bed bath) intervention, regardless of type and frequency. For the purposes of this systematic review, traditional bed bath refers...

Degradation of isobutanal at high loading rates in a compost biofilter.

Science.gov (United States)

Sercu, Bram; Demeestere, Kristof; Baillieul, Hans; Van Langenhove, Herman; Verstraete, Willy

2005-08-01

Biofiltration has been increasingly used for cleaning waste gases, mostly containing low concentrations of odorous compounds. To expand the application area of this technology, the biofiltration of higher pollutant loading rates has to be investigated. This article focuses on the biodegradation of isobutanal (IBAL) in a compost biofilter (BF) at mass loading rates between 211 and 4123 g/m3/day (30-590 ppm(v)). At mass loading rates up to 785 g/m3/day, near 100% removal efficiencies could be obtained. However, after increasing the loading rate to 1500-1900 g/m3/ day, the degradation efficiency decreased to 62-98%. In addition, a pH decrease and production of isobutanol (IBOL) and isobutyric acid (IBAC) were observed. This is the first report showing that an aldehyde can act as electron donor as well as acceptor in a BF. To study the effects of pH, compost moisture content, and electron acceptor availability on the biofiltration of IBAL, IBOL, and IBAC, additional batch and continuous experiments were performed. A pH of 5.2 reduced the IBAL degradation rate and inhibited the IBOL degradation, although adaptation of the microorganisms to low pH was observed in the BFs. IBAC was not degraded in the batch experiments. High moisture content (51%) initially had no effect on the IBOL production, although it negatively affected the IBAL elimination increasingly during a 21-day time-course experiment. In batch experiments, the reduction of IBAL to IBOL did not decrease when the amount of available electron acceptors (oxygen or nitrate) was increased. The IBAL removal efficiency at higher loading rates was limited by a combination of nutrient limitation, pH decrease, and dehydration, and the importance of each limiting factor depended on the influent concentration.

Understanding the fate of organic micropollutants in sand and granular activated carbon biofiltration systems

Energy Technology Data Exchange (ETDEWEB)

Paredes, L., E-mail: lidia.paredes@usc.es; Fernandez-Fontaina, E., E-mail: eduardo.fernandez.fontaina@usc.es; Lema, J.M., E-mail: juan.lema@usc.es; Omil, F., E-mail: francisco.omil@usc.es; Carballa, M., E-mail: marta.carballa@usc.es

2016-05-01

In this study, sand and granular activated carbon (GAC) biofilters were comparatively assessed as post-treatment technologies of secondary effluents, including the fate of 18 organic micropollutants (OMPs). To determine the contribution of adsorption and biotransformation in OMP removal, four reactors were operated (two biofilters (with biological activity) and two filters (without biological activity)). In addition, the influence of empty bed contact time (EBCT), ranging from 0.012 to 3.2 d, and type of secondary effluent (anaerobic and aerobic) were evaluated. Organic matter, ammonium and nitrate were removed in both biofilters, being their adsorption higher on GAC than on sand. According to the behaviour exhibited, OMPs were classified in three different categories: I) biotransformation and high adsorption on GAC and sand (galaxolide, tonalide, celestolide and triclosan), II) biotransformation, high adsorption on GAC but low or null adsorption on sand (ibuprofen, naproxen, fluoxetine, erythromycin, roxythromycim, sulfamethoxazole, trimethoprim, bisphenol A, estrone, 17β-estradiol and 17α-ethinylestradiol), and, III) only adsorption on GAC (carbamazepine, diazepam and diclofenac). No influence of EBCT (in the range tested) and type of secondary effluent was observed in GAC reactors, whereas saturation and kinetic limitation of biotransformation were observed in sand reactors. Taking into account that most of the organic micropollutants studied (around 60%) fell into category II, biotransformation is crucial for the elimination of OMPs in sand biofilters. - Highlights: • OMP removal was comparatively assessed in sand and GAC biofilters. • The contribution of adsorption and biotransformation in OMP removal was identified. • The filtering material did not affect the biological activities in biofilters. • There is no direct correlation between EBCT and OMP removal in biofilters. • The type of secondary effluent determines the lifespan of filtering

Understanding the fate of organic micropollutants in sand and granular activated carbon biofiltration systems

International Nuclear Information System (INIS)

Paredes, L.; Fernandez-Fontaina, E.; Lema, J.M.; Omil, F.; Carballa, M.

2016-01-01

In this study, sand and granular activated carbon (GAC) biofilters were comparatively assessed as post-treatment technologies of secondary effluents, including the fate of 18 organic micropollutants (OMPs). To determine the contribution of adsorption and biotransformation in OMP removal, four reactors were operated (two biofilters (with biological activity) and two filters (without biological activity)). In addition, the influence of empty bed contact time (EBCT), ranging from 0.012 to 3.2 d, and type of secondary effluent (anaerobic and aerobic) were evaluated. Organic matter, ammonium and nitrate were removed in both biofilters, being their adsorption higher on GAC than on sand. According to the behaviour exhibited, OMPs were classified in three different categories: I) biotransformation and high adsorption on GAC and sand (galaxolide, tonalide, celestolide and triclosan), II) biotransformation, high adsorption on GAC but low or null adsorption on sand (ibuprofen, naproxen, fluoxetine, erythromycin, roxythromycim, sulfamethoxazole, trimethoprim, bisphenol A, estrone, 17β-estradiol and 17α-ethinylestradiol), and, III) only adsorption on GAC (carbamazepine, diazepam and diclofenac). No influence of EBCT (in the range tested) and type of secondary effluent was observed in GAC reactors, whereas saturation and kinetic limitation of biotransformation were observed in sand reactors. Taking into account that most of the organic micropollutants studied (around 60%) fell into category II, biotransformation is crucial for the elimination of OMPs in sand biofilters. - Highlights: • OMP removal was comparatively assessed in sand and GAC biofilters. • The contribution of adsorption and biotransformation in OMP removal was identified. • The filtering material did not affect the biological activities in biofilters. • There is no direct correlation between EBCT and OMP removal in biofilters. • The type of secondary effluent determines the lifespan of filtering

Effects of Bed Rest on Conduction Velocity of the Triceps Surae Stretch Reflex and Postural Control

Science.gov (United States)

Reschke, M. F.; Wood, S. J.; Cerisano, J. M.; Kofman, I. S.; Fisher, E. A.; Esteves, J. T.; Taylor, L. C.; DeDios, Y. E.; Harm, D. L.

2011-01-01

Despite rigorous exercise and nutritional management during space missions, astronauts returning from microgravity exhibit neuromuscular deficits and a significant loss in muscle mass in the postural muscles of the lower leg. Similar changes in the postural muscles occur in subjects participating in long-duration bed rest studies. These adaptive muscle changes manifest as a reduction in reflex conduction velocity during head-down bed rest. Because the stretch reflex encompasses both the peripheral (muscle spindle and nerve axon) and central (spinal synapse) components involved in adaptation to calf muscle unloading, it may be used to provide feedback on the general condition of neuromuscular function, and might be used to evaluate the effectiveness of countermeasures aimed at preserving muscle mass and function during periods of unloading. Stretch reflexes were measured on 18 control subjects who spent 60 to 90 days in continuous 6 deg head-down bed rest. Using a motorized system capable of rotating the foot around the ankle joint (dorsiflexion) through an angle of 10 degrees at a peak velocity of about 250 deg/sec, a stretch reflex was recorded from the subject's left triceps surae muscle group. Using surface electromyography, about 300 reflex responses were obtained and ensemble-averaged on 3 separate days before bed rest, 3 to 4 times in bed, and 3 times after bed rest. The averaged responses for each test day were examined for reflex latency and conduction velocity (CV) across gender. Computerized posturography was also conducted on these same subjects before and after bed rest as part of the standard measures. Peak-to-peak sway was measured during Sensory Organization Tests (SOTs) to evaluate changes in the ability to effectively use or suppress visual, vestibular, and proprioceptive information for postural control. Although no gender differences were found, a significant increase in reflex latency and a significant decrease in CV were observed during the bed

Effects of near-bed turbulence and micro-topography on macroinvertebrate movements across contrasting gravel-bed surfaces (Invited)

Science.gov (United States)

Buffin-Belanger, T. K.; Rice, S. P.; Reid, I.; Lancaster, J.

2009-12-01

Fluvial habitats can be described from a series of physical variables but to adequately address the habitat quality it becomes necessary to develop an understanding that combines the physical variables with the behaviour of the inhabitating organisms. The hypothesis of flow refugia provide a rational that can explain the persistence of macroinvertebrate communities in gravel-bed rivers when spates occur. The movement behaviour of macroinvertebrates is a key element to the flow refugia hypothesis, but little is known about how local near-bed turbulence and bed microtopography may affect macroinvertebrate movements. We reproduced natural gravel-bed substrates with contrasting gravel bed textures in a large flume where we were able to document the movement behaviour of the cased caddisfly Potamophylax latipennis for a specific discharge. The crawling paths and drift events of animals were analysed from video recordings. Characteristics of movements differ from one substrate to another. The crawling speed is higher for the small grain-size substrates but the mean travel distance remains approximately the same between substrates. For each substrate, the animals tended to follow consistent paths across the surface. The number of drift events and mean distance drifted is higher for the small grain-size substrate. ADV measurements close to the boundary allow detailed characterisation of near-bed hydraulic variables, including : skewness coefficients, TKE, UV correlation coefficients and integral time scales from autocorrelation analysis. For these variables, the vertical patterns of turbulence parameters are similar between the substrates but the amplitude of the average values and standard errors vary significantly. The spatial distribution of this variability is considered in relation to the crawling paths. It appears that the animals tend to crawl within areas of the substrate where low flow velocities and low turbulent kinetic energies are found, while sites that

Experimental study and large eddy simulation of effect of terrain slope on marginal burning in shrub fuel beds

Science.gov (United States)

Xiangyang Zhou; Shankar Mahalingam; David Weise

2007-01-01

This paper presents a combined study of laboratory scale fire spread experiments and a three-dimensional large eddy simulation (LES) to analyze the effect of terrain slope on marginal burning behavior in live chaparral shrub fuel beds. Line fire was initiated in single species fuel beds of four common chaparral plants under various fuel bed configurations and ambient...

Bed Bug Infestations and Control Practices in China: Implications for Fighting the Global Bed Bug Resurgence

Directory of Open Access Journals (Sweden)

Changlu Wang

2011-04-01

Full Text Available The bed bug resurgence in North America, Europe, and Australia has elicited interest in investigating the causes of the widespread and increasing infestations and in developing more effective control strategies. In order to extend global perspectives on bed bug management, we reviewed bed bug literature in China by searching five Chinese language electronic databases. We also conducted telephone interviews of 68 pest control firms in two cities during March 2011. In addition, we conducted telephone interviews to 68 pest control companies within two cities in March 2011. Two species of bed bugs (Cimex lectularius L. and Cimex hemipterus (F. are known to occur in China. These were common urban pests before the early1980s. Nationwide “Four-Pest Elimination” campaigns (bed bugs being one of the targeted pests were implemented in China from 1960 to the early 1980s. These campaigns succeeded in the elimination of bed bug infestations in most communities. Commonly used bed bug control methods included applications of hot water, sealing of bed bug harborages, physical removal, and applications of residual insecticides (mainly organophosphate sprays or dusts. Although international and domestic travel has increased rapidly in China over the past decade (2000–2010, there have only been sporadic new infestations reported in recent years. During 1999–2009, all documented bed bug infestations were found in group living facilities (military dormitories, worker dormitories, and prisons, hotels, or trains. One city (Shenzhen city near Hong Kong experienced significantly higher number of bed bug infestations. This city is characterized by a high concentration of migratory factory workers. Current bed bug control practices include educating residents, washing, reducing clutter, putting items under the hot sun in summer, and applying insecticides (pyrethroids or organophosphates. There have not been any studies or reports on bed bug insecticide

Numerical modelling for the effective thermal conductivity of lithium meta titanate pebble bed with different packing structures

Energy Technology Data Exchange (ETDEWEB)

Panchal, Maulik, E-mail: maulikpanchal@ipr.res.in [Institute for Plasma Research, Bhat, Gandhinagar-382428 (India); Chaudhuri, Paritosh [Institute for Plasma Research, Bhat, Gandhinagar-382428 (India); Van Lew, Jon T; Ying, Alice [UCLA, MAE Department, Los Angeles, CA 90095-1597 (United States)

2016-11-15

Highlights: • The effective thermal conductivity (k{sub eff}) of lithium meta-titanate (Li{sub 2}TiO{sub 3}) pebble beds is an important parameter for the design and analysis of TBM in ITER. • The k{sub eff} of Li{sub 2}TiO{sub 3} pebble beds under stagnant helium gas have been determined numerically using different uniform packing structures and random close packing (RCP) structures. • k{sub eff} of Li{sub 2}TiO{sub 3} pebble beds with different packing fractions have been reported as function of temperature; k{sub eff} of the RCP Li{sub 2}TiO{sub 3} pebble bed is compared with reported experimental results. • The numerically-determined k{sub eff} of the RCP Li{sub 2}TiO{sub 3} pebble bed agrees reasonably well with the experimental data and Zehner-Schlunder correlation. - Abstract: The effective thermal conductivity (k{sub eff}) of lithium meta-titanate (Li{sub 2}TiO{sub 3}) pebble beds is an important parameter for the design and analysis of IN LLCB TBM (Indian Lead Lithium Ceramic Breeder Test Blanket Module). The k{sub eff} of Li{sub 2}TiO{sub 3} pebble beds under stagnant helium gas have been determined numerically using different uniform packing structures and random close packing (RCP) structures. The uniform packing structures of Li{sub 2}TiO{sub 3} pebble bed are modelled by using the simple cubic, body centered cubic and face centered cubic arrangement. The packing structure of the RCP bed of Li{sub 2}TiO{sub 3} pebbles is generated with the discrete element method (DEM) code. k{sub eff} of Li{sub 2}TiO{sub 3} pebble beds with different packing fractions have been reported as function of temperature; k{sub eff} of the RCP Li{sub 2}TiO{sub 3} pebble bed is compared with reported experimental results from literature. The numerically determined k{sub eff} of the Li{sub 2}TiO{sub 3} pebble bed agrees reasonably well with the experimental data.

Selection of commercial biofilters for rearing aquatic animals in closed system

Directory of Open Access Journals (Sweden)

Chuayrodmod, J.

2007-07-01

Full Text Available A comparative study was made to select the most suitable biofilter from 7 types of commercial water filters by rearing hybrid catfish (Clarias macrocephalus x C. gariepinus in aquaria for 64 days. It was found that diminishing concentrations of ammonia and nitrite were attributed mainly to nitrifying bacteria that convert ammonia into nitrite and nitrate which required a minimum period of 16-28 days for the process to function. Low absorption of ammonia was achieved through using activated carbon, coconut shell charcoal, zeolite and ceramic. Durability and filtering efficiency of the filters depended upon porosity and amount of biofilm on the filter surface. The filter using one coarse meshed plastic sheet and 37 bioballs was the most suitable, though it caused a problem with low total alkalinity resulting in mortality of the biofilm which peeled off, thus increasing the concentrations of ammonia, nitrite and suspended solids toward the end of the experimental period. The catfish growth rate, survival and FCR in all treatments were in the ranges of 7.39-8.91 g/d, 84.44-95.56% and 0.21-0.25, respectively.

Control of the Bed Temperature of a Circulating Fluidized Bed Boiler by using Particle Swarm Optimization

Directory of Open Access Journals (Sweden)

AYGUN, H.

2012-05-01

Full Text Available Circulating fluidized bed boilers are increasingly used in the power generation due to their higher combustion efficiency and lower pollutant emissions. Such boilers require an effective control of the bed temperature, because it influences the boiler combustion efficiency and the rate of harmful emissions. A Particle-Swarm-Optimization-Proportional-Integrative-Derivative (PSO-PID controller for the bed temperature of a circulating fluidized bed boiler is presented. In order to prove the capability of the proposed controller, its performances are compared at different boiler loads with those of a Fuzzy Logic (FL controller. The simulation results demonstrate some advantages of the proposed controller.

Bed Bug Guidance for School Nurses

Science.gov (United States)

School nurses are often called upon to provide vital information to students, parents, teachers, and administrators. These tips on identifying, managing and preventing bed bugs will help you to effectively respond if bed bugs appear in your school.

Bed Bugs

Science.gov (United States)

Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

Comparison of the Effects of Fluidized-Bed and Fixed-Bed Reactors in Microwave-Assisted Catalytic Decomposition of TCE by Hydrogen

Directory of Open Access Journals (Sweden)

Lili Ren

2012-01-01

Full Text Available Trichloroethylene (TCE decomposition by hydrogen with microwave heating under different reaction systems was investigated. The activities of a series of catalysts for microwave-assisted TCE hydrodechlorination were tested through the fixed-bed and the fluidized-bed reactor systems. This study found that the different reaction system is suitable for different catalyst type. And there is an interactive relationship between the catalyst type and the reaction bed type.

Effect of 2 Bedding Materials on Ammonia Levels in Individually Ventilated Cages.

Science.gov (United States)

Koontz, Jason M; Kumsher, David M; Kelly, Richard; Stallings, Jonathan D

2016-01-01

This study sought to identify an optimal rodent bedding and cage-change interval to establish standard procedures for the IVC in our rodent vivarium. Disposable cages were prefilled with either corncob or α-cellulose bedding and were used to house 2 adult Sprague-Dawley rats (experimental condition) or contained no animals (control). Rats were observed and intracage ammonia levels measured daily for 21 d. Intracage ammonia accumulation became significant by day 8 in experimental cages containing α-cellulose bedding, whereas experimental cages containing corncob bedding did not reach detectable levels of ammonia until day 14. In all 3 experimental cages containing α-cellulose, ammonia exceeded 100 ppm (our maximum acceptable limit) by day 11. Two experimental corncob cages required changing at days 16 and 17, whereas the remaining cage containing corncob bedding lasted the entire 21 d without reaching the 100-ppm ammonia threshold. These data suggests that corncob bedding provides nearly twice the service life of α-cellulose bedding in the IVC system.

Effects of disking, bedding, and subsoiling on survival and growth of three oak species in central Mississippi

Science.gov (United States)

J. Paul Jeffreys; Emily B. Schultz; Thomas G. Matney; W. Cade Booth; Jason M. Morris

2010-01-01

A replicated split-plot design experiment to evaluate the effects of three site preparation methods (disking, bedding, and subsoiling plus bedding) on survival and growth of three oak species (cherrybark, Quercus pagoda Raf.; Shumard, Quercus shumardii Buckl.; and Nuttall, Quercus texana Buckl.) was established...

Effectiveness of a Reduced-Risk Insecticide Based Bed Bug Management Program in Low-Income Housing

Directory of Open Access Journals (Sweden)

Narinderpal Singh

2013-11-01

Full Text Available Bed bug (Cimex lectularius L. infestations are becoming increasingly common in low-income communities. Once they are introduced, elimination is very difficult. As part of the efforts to develop effective and safe bed bug management programs, we conducted a laboratory study evaluating the efficacy of a reduced-risk insecticide—Alpine aerosol (0.5% dinotefuran. We then conducted a field evaluation of a reduced-risk insecticide based integrated pest management (IPM program in low-income family apartments with young children. In laboratory evaluations, direct spray and 5 min exposure to dry Alpine aerosol residue caused 100.0 ± 0.0 and 91.7 ± 8.3% mortality to bed bug nymphs, respectively. Direct Alpine aerosol spray killed 91.3 ± 4.3% of the eggs. The IPM program included education, steam, bagging infested linens, placing intercepting devices under furniture legs and corners of rooms, applying Alpine aerosol and Alpine dust (0.25% dinotefuran, 95% diatomaceous earth dust, and regularly scheduled monitoring and re-treatment. Nine apartments ranging from 1–1,428 (median: 29 bed bugs based on visual inspection and Climbup interceptor counts were included. Over a 6-month period, an average 172 g insecticide (Alpine aerosol + Alpine dust was used in each apartment, a 96% reduction in pesticide usage compared to chemical only treatment reported in a similar environment. The IPM program resulted in an average of 96.8 ± 2.2% reduction in the number of bed bugs. However, elimination of bed bugs was only achieved in three lightly infested apartments (<30 bed bugs at the beginning. Elimination success was closely correlated with the level of bed bug populations.

Effects of bed-rest on urea and creatinine: correlation with changes in fat-free mass.

Science.gov (United States)

Bilancio, Giancarlo; Lombardi, Cinzia; Pisot, Rado; De Santo, Natale G; Cavallo, Pierpaolo; Cirillo, Massimo

2014-01-01

Bed-rest experiments are designed for investigation on catabolic effects of hypokinetic conditions and/or for microgravity simulation in on-ground aerospace research. Bed-rest effects include a reduction in fat-free mass and muscle mass. Urea and creatinine are catabolites of endogenous protein and of muscular energetic metabolism which are excreted mainly by the kidney. The study investigated on urea, creatinine, and kidney function during bed-rest. Twenty healthy young men underwent a 7-day adaptation period (day-6 to day-0) and a 35-day bed-rest experiment (day1 to day35) during normocaloric diet. Urine were collected from day-3 to day0 (baseline) and from day1 to day35. Blood samples and anthropometrical data were collected at day0 (baseline) and bed-rest days 7, 14, 21, 28, and 35. Bed-rest reduced plasma volume, weight, fat-free mass, and muscle mass (Pcreatinine, and no change in urinary creatinine. The overall integral of changes from day0 to day35 was on average +101.7 mg/dL for plasma urea (95%CI = +43.4/+159.9), +82.2 g/24 h for urinary urea (95%CI = +55.8/+108.7), -2.5 mg/dL for plasma creatinine (95%CI = -3.1/-1.9). Bed-rest reduced plasma cistatyn C also, which was used as mass-independent marker of glomerular filtration rate (-13.1%, P<0.05). Correlations with final reduction in fat-free mass and muscle mass were significant for the overall integral of changes in urinary urea from day0 to day35 (R = 0.706, P<0.001) and for early changes in urinary urea and plasma urea from day0 to day7 (R = 0.566, P = 0.009 and R = 0.715, P<0.001, respectively). Study results shows that urea is a marker of catabolic conditions secondary to hypokinetic conditions.

Udder health in a Danish compost bedded pack barn

DEFF Research Database (Denmark)

Svennesen, Line; Enevoldsen, Carsten; Bjerg, Bjarne Schmidt

Besides welfare advantages of the compost bedded pack system (CBP) there could be a negative effect of the organic bedding on udder health. Our objectives were to evaluate the effects of a CBP on udder health compared to a free stall system (FS) with sand bedded cubicles. Within the same Danish...

Bed agglomeration characteristics of palm shell and corncob combustion in fluidized bed

International Nuclear Information System (INIS)

Chaivatamaset, Pawin; Sricharoon, Panchan; Tia, Suvit

2011-01-01

Bed particle agglomeration was studied experimentally in an atmospheric laboratory scale fluidized bed combustor using quartz sand as bed material. Palm shell and corncob were tested. The objectives of the study were (i) to describe the contributions of the biomass ash properties and the operating conditions on the bed agglomeration tendency in term of the bed defluidization time (t def ) and the extent of potassium accumulation in the bed (K/Bed) and (ii) to further elucidate the ash inorganic behaviors and the governing bed agglomeration mechanisms. Defluidization caused by the bed agglomeration was experienced in all experiments during combustion of these biomasses, as a consequence of the presence of potassium in biomass. The experimental results indicated that biomass ash characteristics were the significant influence on the bed agglomeration. The increasing bed temperature, bed particle size and static bed height and the decreasing fluidizing air velocity enhanced the bed agglomeration tendency. The SEM/EDS analyses on the agglomerates confirmed that the agglomeration was attributed to the formation of potassium silicate liquid enriched on the surface of quartz sand particles in conjunction with the high surface temperature of the burning biomass char particles. Thermodynamic examination based on the phase diagram analysis confirmed that the molten phase formation was responsible for the agglomeration. In this study, the high molten ash fraction resulting from the high potassium content in biomass promoted the agglomeration and thus defluidization. - Highlights: → Palm shell and corncob of Thailand are tested their bed agglomeration behaviors during fluidized bed combustion. → The increase of bed temperature, bed particle size and static bed height and the decrease of air velocity enhance bed agglomeration. → The formation of ash derived potassium silicate melts enriched on sand surface is the key process. → The collision between char and sand

Experimental Investigation of the Effect of Particle Shape on Frictional Pressure drop in Particulate Debris Bed

International Nuclear Information System (INIS)

Park, Jin Ho; Kim, Eun Ho; Park, Hyun Sun

2014-01-01

To ensure the long-term cooling of corium in the reactor cavity, it is important to ensure the coolant ingression into the internally heat generated corium debris bed which is governed by pressure drop in porous media. For this reason, it is necessary to understand pressure drop mechanisms in porous bed to verify the feasibility of water penetration into particulate debris bed. According to the previous investigations on molten fuel-coolant interaction (FCI) experiments, it was found that quenched particulate debris bed was composed of irregular shape particles. Therefore, empirical or semiempirical models based on the Ergun equation (Ergun, 1952) for single-phase flow in porous media composed of single sized spherical particle were developed to consider the effect of particle shape on frictional pressure drop by means of adding a shape factor or modifying the Ergun constants etc. (Leva, 1959, Handley and Heggs, 1968, Macdonald, 1979, Foumeny et al., 1996). An experimental investigate on single-phase frictional pressure drop of water in packed bed was conducted in the transparent cylindrical test section with the inner diameter of 100 mm and the height of 700 mm to study the effect of particle shape on frictional pressure drop in porous media. This paper reports the experimental data for spherical particles with the diameter of 2 mm and 5 mm and cylindrical particles with ED of 2 mm and 5 mm. And also, the experimental data compared with the models to predict frictional pressure drop in particulate bed. The conclusions are summarized as follows. As a result of the experiment to measure frictional pressure drop in particulate bed composed of cylindrical particles the models predict the experimental data well within 22.11 % except the Handley and Heggs model when ED is applied to the models

Experimental Investigation of the Effect of Particle Shape on Frictional Pressure drop in Particulate Debris Bed

Energy Technology Data Exchange (ETDEWEB)

Park, Jin Ho; Kim, Eun Ho; Park, Hyun Sun [POSTECH, Pohang (Korea, Republic of)

2014-10-15

To ensure the long-term cooling of corium in the reactor cavity, it is important to ensure the coolant ingression into the internally heat generated corium debris bed which is governed by pressure drop in porous media. For this reason, it is necessary to understand pressure drop mechanisms in porous bed to verify the feasibility of water penetration into particulate debris bed. According to the previous investigations on molten fuel-coolant interaction (FCI) experiments, it was found that quenched particulate debris bed was composed of irregular shape particles. Therefore, empirical or semiempirical models based on the Ergun equation (Ergun, 1952) for single-phase flow in porous media composed of single sized spherical particle were developed to consider the effect of particle shape on frictional pressure drop by means of adding a shape factor or modifying the Ergun constants etc. (Leva, 1959, Handley and Heggs, 1968, Macdonald, 1979, Foumeny et al., 1996). An experimental investigate on single-phase frictional pressure drop of water in packed bed was conducted in the transparent cylindrical test section with the inner diameter of 100 mm and the height of 700 mm to study the effect of particle shape on frictional pressure drop in porous media. This paper reports the experimental data for spherical particles with the diameter of 2 mm and 5 mm and cylindrical particles with ED of 2 mm and 5 mm. And also, the experimental data compared with the models to predict frictional pressure drop in particulate bed. The conclusions are summarized as follows. As a result of the experiment to measure frictional pressure drop in particulate bed composed of cylindrical particles the models predict the experimental data well within 22.11 % except the Handley and Heggs model when ED is applied to the models.

Stabilizing Effects of Bacterial Biofilms: EPS Penetration and Redistribution of Bed Stability Down the Sediment Profile

Science.gov (United States)

Chen, X. D.; Zhang, C. K.; Zhou, Z.; Gong, Z.; Zhou, J. J.; Tao, J. F.; Paterson, D. M.; Feng, Q.

2017-12-01

Biofilms, consisting of microorganisms and their secreted extracellular polymeric substances (EPSs), serve as "ecosystem engineers" stabilizing sedimentary environments. Natural sediment bed provides an excellent substratum for biofilm growth. The porous structure and rich nutrients allow the EPS matrix to spread deeper into the bed. A series of laboratory-controlled experiments were conducted to investigate sediment colonization of Bacillus subtilis and the penetration of EPS into the sediment bed with incubation time. In addition to EPS accumulation on the bed surface, EPS also penetrated downward. However, EPS distribution developed strong vertical heterogeneity with a much higher content in the surface layer than in the bottom layer. Scanning electron microscope images of vertical layers also displayed different micromorphological properties of sediment-EPS matrix. In addition, colloidal and bound EPSs exhibited distinctive distribution patterns. After the full incubation, the biosedimentary beds were eroded to test the variation of bed stability induced by biological effects. This research provides an important reference for the prediction of sediment transport and hence deepens the understanding of the biologically mediated sediment system and broadens the scope of the burgeoning research field of "biomorphodynamics."

The effect of an acoustic field on the filtration efficiency of aerosols by a granular bed

International Nuclear Information System (INIS)

Tavossi, H.

1985-06-01

A theoretical and an experimental study were developed in order to evaluate the parameters controlling the aerosol collection efficiency of a granular bed, i.e. all the chief collection mechanisms and the effect of acoustic waves on this efficiency. The action of acoustic waves of appropriate intensity and frequency increased the efficiency of the granular bed significantly for all aerosol sizes including those corresponding to the minimum efficiency. The theoretical prediction was verified by an experimental apparatus using a granular bed of glass of 2 mm diameter. Furthermore, our experimental results demonstrated the existence of a threshold in the acoustic intensity above which the collection efficiency of the granular bed increased rapidly. We also demonstrated a semi-empirical law relating acoustic capture efficiency of a spherical collector to frequency and acoustic intensity [fr

Branched-chain amino acid supplementation during bed rest: effect on recovery

Science.gov (United States)

Stein, T. P.; Donaldson, M. R.; Leskiw, M. J.; Schluter, M. D.; Baggett, D. W.; Boden, G.

2003-01-01

Bed rest is associated with a loss of protein from the weight-bearing muscle. The objectives of this study are to determine whether increasing dietary branched-chain amino acids (BCAAs) during bed rest improves the anabolic response after bed rest. The study consisted of a 1-day ambulatory period, 14 days of bed rest, and a 4-day recovery period. During bed rest, dietary intake was supplemented with either 30 mmol/day each of glycine, serine, and alanine (group 1) or with 30 mmol/day each of the three BCAAs (group 2). Whole body protein synthesis was determined with U-(15)N-labeled amino acids, muscle, and selected plasma protein synthesis with l-[(2)H(5)]phenylalanine. Total glucose production and gluconeogenesis from alanine were determined with l-[U-(13)C(3)]alanine and [6,6-(2)H(2)]glucose. During bed rest, nitrogen (N) retention was greater with BCAA feeding (56 +/- 6 vs. 26 +/- 12 mg N. kg(-1). day(-1), P BCAA supplementation on either whole body, muscle, or plasma protein synthesis or the rate of 3-MeH excretion. Muscle tissue free amino acid concentrations were increased during bed rest with BCAA (0.214 +/- 0.066 vs. 0.088 +/- 0.12 nmol/mg protein, P BCAA group in the recovery phase. In conclusion, the improved N retention during bed rest is due, at least in part, to accretion of amino acids in the tissue free amino acid pools. The amount accreted is not enough to impact protein kinetics in the recovery phase but does improve N retention by providing additional essential amino acids in the early recovery phase.

Effect of rolling bed on decubitus in bedridden nursing home patients.

Science.gov (United States)

Izutsu, T; Matsui, T; Satoh, T; Tsuji, T; Sasaki, H

1998-02-01

Decubitus is one of the most difficult management problems encountered in bedridden elderly patients. Relief of pressure over decubitus is the most important principle of the management. We developed a rolling air cushion bed which turns the patient to a 15-degree inclined lateral position with an inflating ripple mattress, a longitudinally aligned air inflatable tube. The position of the patients was changed between right and left laterals and to supine every 15 minutes automatically. Nineteen bedridden patients with decubitus used the rolling air cushion bed for 3 months and 12 bedridden patients with decubitus used a conventional bed and had their position changes every 2 hours by care givers. Severity of decubitus was divided into 4 grades and the decubitus significantly improved from 2.8 (S.E. 0.2) to 2.0 (S.E. 0.3) after 3 months in patients using the rolling air cushion bed, while in patients with conventional beds it changed from 3.0 (S.E. 0.2) to 3.2 (S.E. 0.2) (not statistically significant). We suggest that the rolling air cushion bed would be beneficial to decubitus relief in bedridden elderly and may relieve labor by care givers.

Confirmation of Monod Model for Biofiltration of Styrene Vapors from Waste Flue Gas

Directory of Open Access Journals (Sweden)

Reza Dehghanzadeh

2012-12-01

Full Text Available Background: The objective of this research was to investigate the kinetic behavior of the biofil-tration process for the removal of styrene.Methods: A three stage compost based biofilter was inoculated with thickened activated sludge. The reaction order rate constants were obtained from continuous experiments and used as the specific growth rate for the Monod equation.Results: The measured concentration profiles show a linear dependence on the bed height in the biofilter at higher loadings, such as 75 and 45 g m-3 h-1. This is the condition of reaction limitation for a reaction with zero-order kinetics. From the experimental data, maximum elimination capac-ity (ECmax was estimated to be 44, 40 and 26 g m-3 h-1 at empty bed retention times (EBRTs of 120, 60 and 30 s, respectively. However, at lower loadings, the measured concentration profile of the biofilter is one of exponential increase, which is the condition of both reaction and diffusion limitations for a reaction with zero-order kinetics. Maximum elimination capacities found from the experimental results were the same as Monod model predictions. Both the experimental re-sults and the model predictions showed the influence of EBRT on the removal rate of styrene, particularly for the highest loading rate.Conclusion: In terms of the practical applications of the proposed models have the advantage of being simpler than Monod kinetics and Monod kinetics requires a numerical solution.

Confirmation of Monod Model for Biofiltration of Styrene Vapors from Waste Flue Gas

Science.gov (United States)

Dehghanzadeh, Reza; Roshani, Babak; Asadi, Mahzar; Fahiminia, Mohammad; AslHashemi, Ahmad

2012-01-01

Background: The objective of this research was to investigate the kinetic behavior of the biofil¬tration process for the removal of styrene. Methods: A three stage compost based biofilter was inoculated with thickened activated sludge. The reaction order rate constants were obtained from continuous experiments and used as the specific growth rate for the Monod equation. Results: The measured concentration profiles show a linear dependence on the bed height in the biofilter at higher loadings, such as 75 and 45 g m-3 h-1. This is the condition of reaction limitation for a reaction with zero-order kinetics. From the experimental data, maximum elimination capac¬ity (ECmax) was estimated to be 44, 40 and 26 g m-3 h-1 at empty bed retention times (EBRTs) of 120, 60 and 30 s, respectively. However, at lower loadings, the measured concentration profile of the biofilter is one of exponential increase, which is the condition of both reaction and diffusion limitations for a reaction with zero-order kinetics. Maximum elimination capacities found from the experimental results were the same as Monod model predictions. Both the experimental re¬sults and the model predictions showed the influence of EBRT on the removal rate of styrene, particularly for the highest loading rate. Conclusion: In terms of the practical applications of the proposed models have the advantage of being simpler than Monod kinetics and Monod kinetics requires a numerical solution. PMID:24688940

The effects of baffles and gas superficial velocity on a bubble fluidized bed reactor's applications

International Nuclear Information System (INIS)

Ghorbanpour, A.; Ghannadi Maragheh, M.; Mallah, M. H.

2008-01-01

Baffles are used for decreasing bubbles diameter in order to increase the conversion rate along the bubbling fluidized bed reactors. The appearance of this phenomenon is due to bursting of the bubbles during the pass of bubbles from baffles. In this work, a computerized modeling and simulation have been performed in order to obtain a fundamental knowledge of the influence of the baffles on the bubble diameter and the specific mass transfer area. The height of the bed is 5 meters and its diameter is 0.3 meter. Baffles are located at 1 and 2 meters from the bottom of the bed. A two phase model together with a comprehensive fluid dynamical description of bubbling fluidized is presented. The effects of baffles and gas superficial velocity on the operating behavior of fluidized bed reactors are considered. The results are compared to the previously reported documents, and the experiments which have been carried out. MATLAB software is used in this simulation

Thermofluid effect on energy storage in fluidized bed reactor

Science.gov (United States)

Mahfoudi, Nadjiba; El Ganaoui, Mohammed; Moummi, Abdelhafid

2016-05-01

The development of innovative systems of heat storage is imperative to improve the efficiency of the existing systems used in the thermal solar energy applications. Several techniques were developed and realized in this context. The technology of the sand fluidized bed (sandTES) offers a promising alternative to the current state-of-the-art of the heat storage systems, such as fixed bed using a storage materials, as sand, ceramic, and stones, etc. Indeed, the use of the fluidization technique allows an effective heat transfer to the solid particles. With the sand, an important capacity of storage is obtained by an economic and ecological material [N. Mahfoudi, A. Moummi, M. El Ganaoui, Appl. Mech. Mater. 621, 214 (2014); N. Mahfoudi, A. Khachkouch, A. Moummi B. Benhaoua, M. El Ganaoui, Mech. Ind. 16, 411 (2015); N. Mahfoudi, A. Moummi, M. El Ganaoui, F. Mnasri, K.M. Aboudou, 3e Colloque internationale Francophone d"énergétique et mécanique, Comores, 2014, p. 91]. This paper presents a CFD simulation of the hydrodynamics and the thermal transient behavior of a fluidized bed reactor of sand, to determine the characteristics of storage. The simulation shows a symmetry breaking that occurs and gave way to chaotic transient generation of bubble formation after 3 s. Furthermore, the predicted average temperature of the solid phase (sand) increases gradually versus the time with a gain of 1 °C in an interval of 10 s. Contribution to the topical issue "Materials for Energy Harvesting, Conversion and Storage (ICOME 2015) - Elected submissions", edited by Jean-Michel Nunzi, Rachid Bennacer and Mohammed El Ganaoui

The Safety of Hospital Beds: Ingress, Egress, and In-Bed Mobility.

Science.gov (United States)

Morse, Janice M; Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K; Bloswick, Donald

2015-01-01

To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients' ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients' use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated.

THE EFFECTS OF PROLONGED PHYSICAL INACTIVITY INDUCED BY BED REST ON COGNITIVE FUNCTIONING IN HEALTHY MALE PARTICIPANTS

Directory of Open Access Journals (Sweden)

Petra Dolenc

2013-06-01

Full Text Available A growing body of scientific evidence indicates that physical activity beneficially influences cognitive functioning. Less thoroughly investigated are the cognitive outcomes of reduced physical activity levels. The purpose of the study was to determine the effects of prolonged physical inactivity induced by bed rest on the participant’s cognitive functioning. Bed rest is a well-accepted method by which an acute stage of human adaptation to weightlessness in space flights is simulated, as well as an important model to study the consequences of extreme physical inactivity in humans. The subjects participating in the study consisted of fifteen healthy males aged between 19 and 65 years who were exposed to 14-day horizontal bed rest in a strict hospital environment. To assess the cognitive functions of the participants, a neuropsychological test battery was administered before and after the bed rest experiment. There was no significant impairment in cognitive performance after the 14-day bed rest on all tests, except in the measurements of delayed recall in the group of older adults. The results suggest that cognitive functions remained relatively stable during the period of physical immobilization. The obtained results have been discussed taking the possible contributing factors into account such as the practice effect, the relatively short duration of bed rest, and the choice of the cognitive measures administered. The study also provides evidence that favourable living and psychosocial conditions can protect one against cognitive decline in the case of extreme physical inactivity.

THE USE OF HALLOYSITE TO REDUCE POLLUTIONS CONCENTRATION IN MUNICIPAL WASTEWATER

Directory of Open Access Journals (Sweden)

Alicja Machnicka

2016-12-01

Full Text Available One of the methods of municipal wastewater treatment allows the use of biofilters. The study used a bed filled halloysite. In operation of the bed, depending on the hydraulic load, the concentration of phosphate, ammonium and organic matter was reduced. Highest reduction of the concentration PO43- (89% and N – NH4+ (81% in the waste water of the hydraulic load – 0,04 m3/m2h was obtained. The concentration of the organic substrate was reduced by approximately 86%.

Biofiltration of volatile pollutants: Engineering mechanisms for improved design, long-term operation, prediction, and implementation. 1997 annual progress report

International Nuclear Information System (INIS)

Barton, J.W.; Davison, B.H.; Klasson, K.T.

1997-01-01

operating biofilter. These results will point to further potential improvements in systems of EM priority. Constructed and acclimated three trickling-bed biofilters. Measured kinetic activity and mass transfer in biofilters under study. Demonstrated extended activity of biofilters in absence of supplemental nutrient. Quantified filter regeneration after prolonged starvation. Demonstrated competence of microbial consortium for degrading a variety of C, to C, alkanes as sole carbon and energy sources. Demonstrated competence of microbial consortium for degrading chlorinated alkane as sole carbon and energy sources. Examined solubility enhancement agents. Completed mathematical modeling of biofilm diffusion, reaction, and mass transfer effects for simple cases.'

Effect of Wetting and Contamination of Granular Beds During Sphere Impact

KAUST Repository

Kouraytem, Nadia

2013-03-01

This thesis presents results from an experimental study of the impact of dense solid spheres onto granular beds. The overall aim is to further our understanding of the dynamical response of granular materials to impact. In order to do this, we will study both the initial penetration stages and peak acceleration exerted on the sphere by using high-speed imaging. Another critical part is to measure the penetration depth of the sphere and calculate the corresponding depth-averaged stopping force. Both of these main focal points will be assessed for not only dry, but wet and “contaminated” grains, whereby the granular bed will be comprised of two distinct size ranges of base grains. In doing so, we aim to broadly determine whether contaminated grains or wet grains are more effective at increasing the tensile strength of granular materials.

Fluidized bed roasting of molybdenite-effect of operating variables

International Nuclear Information System (INIS)

Doheim, M.A.; Abdel-Wahab, M.Z.; Rassoul, S.A.

1976-01-01

The results of an investigation on the fluidized bed roasting of molybdenite are reported. Molybdenite mixed with quartz was subjected to an oxidizing roast in a 22 mm diam stainless steel batch fluidized bed reactor. Enriched air (with O 2 ) or diluted air (with N 2 ) was used as the fluidizing and oxidizing gas. In addition to the MoS 2 content of the solids and the O 2 content of the gas, the effect of temperature and flow rate was also examined. For the range of variables investigated, it was found that the temperature influences the rate of the roasting reaction greatly. The gas flow rate affects the conversion favorably up to a certain fluidizing flow rate. An increase in the O 2 content of the gas and the MoS 2 of the solids results in higher conversion levels. The unreacted core kinetic model was applied to the results; and the energy of activation for the reaction was obtained from the Arrhenius plot as 31,100 cal/gmol of MoS 2 . The data obtained should be useful in the design and operation of larger scale roasting reactors

Thermal conductivity of leaf compost used in biofilters: An experimental and theoretical investigation

International Nuclear Information System (INIS)

Chandrakanthi, M.; Mehrotra, A.K.; Hettiaratchi, J.P.A.

2005-01-01

Thermal conductivity is an important property that governs the behaviour of leaf compost biofilters used in treating gaseous pollutants. Measurements were carried out for the thermal conductivity (K) of 44 samples of leaf compost, covering wide ranges of the volume fractions of water (ξ w ), solids (ξ s ) and air (ξ a ), at 20 deg. C using an unsteady state thermal probe. The results indicated that the compost thermal conductivity increased with an increase in ξ w , with a decrease in ξ a , and with an increase in the degree of saturation (defined as the volumetric fraction of water in the total void space). The predictions from the Woodside-Messmer quadratic parallel (QP) model for the thermal conductivity of leaf compost were higher than the experimental values. A simple linear relationship was developed between the thermal conductivity and the degree of saturation, which provided a satisfactory correlation for the data measured in this study as well as those reported recently for sandy and clay loams. -Thermal conductivity of compost exhibits a linear relationship with the degree of saturation of the matrix

Effects of anionic surfactant on n-hexane removal in biofilters.

Science.gov (United States)

Cheng, Yan; He, Huijun; Yang, Chunping; Yan, Zhou; Zeng, Guangming; Qian, Hui

2016-05-01

The biodegradability of three anion surfactants by biofilm microorganisms and the toxicity of the most readily biodegradable surfactant to biofilm microorganisms were examined using batch experiments, and the optimal concentration of SDS for enhanced removal of hexane was investigated using two biotrickling filters (BTFs) for comparison. Results showed that SDS could be biodegraded by microorganisms, and its toxicity to microorganisms within the experimental range was negligible. The best concentration of SDS in biofiltration of n-hexane was 0.1 CMC and the elimination capacity (EC) of 50.4 g m(-3) h(-1) was achieved at a fixed loading rate (LR) of 72 g m(-3) h(-1). When an inlet concentration of n-hexane increased from 600 to 850 mg m(-3), the removal efficiency (RE) decreased from 67% to 41% by BTF2 (with SDS) and from 52% to 42% by BTF1 (without SDS). SDS could enhance hexane removal from 43% (BTF1) to 60% (BTF2) at gas empty-bed residence time (EBRT) of 7.5 s and an inlet concentration of 200 mg m(-3). Copyright © 2016. Published by Elsevier Ltd.

7 CFR 2902.15 - Bedding, bed linens, and towels.

Science.gov (United States)

2010-01-01

... PROCUREMENT Designated Items § 2902.15 Bedding, bed linens, and towels. (a) Definition. (1) Bedding is that... minimum biobased content is 12 percent and shall be based on the amount of qualifying biobased carbon in..., and silk are not qualifying biobased feedstocks for the purpose of determining the biobased content of...

Decreasing ventromedial prefrontal cortex deactivation in risky decision making after simulated microgravity: Effects of -6 degree head-down tilt bed rest

Directory of Open Access Journals (Sweden)

Li-Lin eRao

2014-05-01

Full Text Available Space is characterized by risk and uncertainty. As humans play an important role in long-duration space missions, the ability to make risky decisions effectively is important for astronauts who spend extended time periods in space. The present study used the Balloon Analog Risk Task to conduct both behavioral and fMRI experiments to evaluate the effects of simulated microgravity on individuals’ risk-taking behavior and the neural basis of the effect. The results showed that participants’ risk-taking behavior was not affected by bed rest. However, we found that the ventromedial prefrontal cortex (VMPFC showed less deactivation after bed rest and that the VMPFC activation in the active choice condition showed no significant difference between the win outcome and the loss outcome after bed rest, although its activation was significantly greater in the win outcome than in the loss outcome before bed rest. These results suggested that the participants showed a decreased level of value calculation after the bed rest. Our findings can contribute to a better understanding of the effect of microgravity on individual higher-level cognitive functioning.

Effect of flue gas recirculation on heat transfer in a supercritical circulating fluidized bed combustor

Directory of Open Access Journals (Sweden)

Błaszczuk Artur

2015-09-01

Full Text Available This paper focuses on assessment of the effect of flue gas recirculation (FGR on heat transfer behavior in 1296t/h supercritical coal-fired circulating fluidized bed (CFB combustor. The performance test in supercritical CFB combustor with capacity 966 MWth was performed with the low level of flue gas recirculation rate 6.9% into furnace chamber, for 80% unit load at the bed pressure of 7.7 kPa and the ratio of secondary air to the primary air SA/PA = 0.33. Heat transfer behavior in a supercritical CFB furnace between the active heat transfer surfaces (membrane wall and superheater and bed material has been analyzed for Geldart B particle with Sauter mean diameters of 0.219 and 0.246 mm. Bed material used in the heat transfer experiments had particle density of 2700 kg/m3. A mechanistic heat transfer model based on cluster renewal approach was used in this work. A heat transfer analysis of CFB combustion system with detailed consideration of bed-to-wall heat transfer coefficient distributions along furnace height is investigated. Heat transfer data for FGR test were compared with the data obtained for representative conditions without recycled flue gases back to the furnace through star-up burners.

Defluviimonas denitrificans gen. nov., sp. nov., and Pararhodobacter aggregans gen. nov., sp. nov., non-phototrophic Rhodobacteraceae from the biofilter of a marine aquaculture

DEFF Research Database (Denmark)

Foesel, Bärbel U.; Drake, Harold L.; Schramm, Andreas

2011-01-01

Three Gram-negative bacterial strains were isolated from the biofilter of a recirculating marine aquaculture. They were non-pigmented rods, mesophiles, moderately halophilic, and showed chemoorganoheterotrophic growth on various sugars, fatty acids, and amino acids, with oxygen as electron acceptor......, but clearly separate from, the genera Rhodobacter, Rhodovulum, and Rhodobaca. Based on morphological, physiological, and 16S rRNA-based phylogenetic characteristics, the isolated strains are proposed as new species of two novel genera, Defluviimonas denitrificans gen. nov., sp. nov. (type strain D9-3T = DSM...

Clinical evaluation of an automated turning bed.

Science.gov (United States)

Melland, H I; Langemo, D; Hanson, D; Olson, B; Hunter, S

1999-01-01

The purposes of this study were to assess client comfort and sleep quality, client physiologic response (skin and respiratory status), the effect on the need for caregiver assistance, and cost when using an automated turning bed. Nonexperimental, evaluative study. Twenty-four adult home or long-term care resident subjects who had a degenerative disease, spinal cord injury, stroke, cerebral palsy, or back surgery. Each subject agreed to use the automated turning bed for four weeks. Researchers completed a demographic survey and skin assessment, and assessed each subject for pressure ulcer risk and for the need of assistance of a care giver for turning before and after the four weeks of using the turning bed. Subjects rated the turning bed in terms of comfort and sleep quality. Subjects rated the turning bed as more comfortable than their own bed and expressed satisfaction at the pain relief attained when on the turning bed. While using the turning bed, there was a significant improvement in sleep quality. No skin breakdown or deterioration in respiratory status occurred. Fewer subjects required the assistance of a caregiver for turning when on the turning bed. This automated turning bed shows great promise in meeting a need for patients with limited mobility whether they are homebound or in a residential community. Future studies that further investigate use of the turning bed for postoperative back patients while still in the acute care setting are indicated. Replicative studies with a larger sample size are also indicated.

Comparison of correlations for heat transfer in sphere-pac beds

International Nuclear Information System (INIS)

Fundamenski, W.R.; Gierszewski, P.J.

1991-08-01

The design of a tritium breeding blanket for a fusion reactor requires the knowledge of heat transfer within the blanket. In this paper three models for effective bed heat transfer are compared against the experimental database in order to choose a reference correlation to be used in blanket design. Two parameters are used to describe heat transfer in a packed bed: effective thermal conductivity of the bed, and a heat transfer coefficient at the bed-solid interface

Bed slope effects on turbulent wave boundary layers: 1. Model validation and quantification of rough-turbulent results

DEFF Research Database (Denmark)

Fuhrman, David R.; Fredsøe, Jørgen; Sumer, B. Mutlu

2009-01-01

measurements for steady streaming induced by a skewed free stream velocity signal is also provided. We then simulate a series of experiments involving oscillatory flow in a convergent-divergent smooth tunnel, and a good match with respect to bed shear stresses and streaming velocities is achieved......A numerical model solving incompressible Reynolds-averaged Navier-Stokes equations, combined with a two-equation k-omega turbulence closure, is used to study converging-diverging effects from a sloping bed on turbulent (oscillatory) wave boundary layers. Bed shear stresses from the numerical model....... The streaming is conceptually explained using analogies from steady converging and diffuser flows. A parametric study is undertaken to assess both the peak and time-averaged bed shear stresses in converging and diverging half periods under rough-turbulent conditions. The results are presented as friction factor...

in Spouted Bed

Directory of Open Access Journals (Sweden)

Bronislaw Buczek

2013-01-01

Full Text Available Samples of active coke, fresh and spent after cleaning flue gases from communal waste incinerators, were investigated. The outer layers of both coke particles were separately removed by comminution in a spouted bed. The samples of both active cokes were analysed by means of densities, mercury porosimetry, and adsorption technique. Remaining cores were examined to determine the degree of consumption of coke by the sorption of hazardous emissions (SO2, HCl, and heavy metals through its bed. Differences in contamination levels within the porous structure of the particles were estimated. The study demonstrated the effectiveness of commercial active coke in the cleaning of flue gases.

Semi-dry flue gas desulfurization using Ca(OH)2 in a fluidized bed reactor with bed materials

International Nuclear Information System (INIS)

Park, Young Oak; Roh, Hak Jae; Oh, Chang Sup; Kim, Yong Ha

2010-01-01

The main objective of present work is to reduce sulfur dioxide emission from power plant for the environment protection. The fluidized bed (FB) was used as the reactor with bed materials in a new semi-dry flue gas desulfurization (FGD) process to achieve high desulfurization efficiency (>98%). Fine powder of Ca(OH) 2 as sorbent and water were continuously fed separately to the bed reactor where bed materials (2 mm glass beads) were fluidized vigorously with flue gas (flow 720 Nm 3 / hr) using bench scale plant of stainless steel column. We have investigated different effects of water injection flow rate, Ca/ S molar ratio and weight of bed materials on SO 2 removal. The increments in the Ca/ S molar ratio and water injection flow rate have been resulted higher desulfurization efficiency with certain disadvantages such as higher sorbent cost and lower temperature of the treated flue gas, respectively. (author)

Bed-To-Wall Heat Transfer in a Supercritical Circulating Fluidised Bed Boiler

Directory of Open Access Journals (Sweden)

Błaszczuk Artur

2014-06-01

Full Text Available The purpose of this work is to find a correlation for heat transfer to walls in a 1296 t/h supercritical circulating fluidised bed (CFB boiler. The effect of bed-to-wall heat transfer coefficient in a long active heat transfer surface was discussed, excluding the radiation component. Experiments for four different unit loads (i.e. 100% MCR, 80% MCR, 60% MCR and 40% MCR were conducted at a constant excess air ratio and high level of bed pressure (ca. 6 kPa in each test run. The empirical correlation of the heat transfer coefficient in a large-scale CFB boiler was mainly determined by two key operating parameters, suspension density and bed temperature. Furthermore, data processing was used in order to develop empirical correlation ranges between 3.05 to 5.35 m·s-1 for gas superficial velocity, 0.25 to 0.51 for the ratio of the secondary to the primary air, 1028 to 1137K for bed temperature inside the furnace chamber of a commercial CFB boiler, and 1.20 to 553 kg·m-3 for suspension density. The suspension density was specified on the base of pressure measurements inside the boiler’s combustion chamber using pressure sensors. Pressure measurements were collected at the measuring ports situated on the front wall of the combustion chamber. The obtained correlation of the heat transfer coefficient is in agreement with the data obtained from typical industrial CFB boilers.

Experimental results on the coolability of a debris bed with multidimensional cooling effects

International Nuclear Information System (INIS)

Rashid, M.; Kulenovic, R.; Laurien, E.; Nayak, A.K.

2011-01-01

Research highlights: ► Performing of dryout experiments with a polydispersed bed for top- and bottom-flooding. ► Study of influence of different down comer configurations on the coolability of debris bed. ► Measurement of temperature profiles, pressure drops and determination of dryout heat flux. ► Observation of noticeable increase in coolability of debris bed with the use of down comer is observed. - Abstract: Within the reactor safety research, the removal of decay heat from a debris bed (formed from corium and residual water) is of great importance. In order to investigate experimentally the long term coolability of debris beds, the scaled test facility “DEBRIS” (Fig. 1) has been built at IKE. A large number of experiments had been carried out to investigate the coolability limits for different bed configurations (). Analyses based on one-dimensional configurations underestimate the coolability in realistic multidimensional configurations, where lateral water access and water inflow via bottom regions are favoured. Following the experiments with top- and bottom-flooding flow conditions this paper presents experimental results of boiling and dryout tests at different system pressures based on top- and bottom-flooding via a down comer configuration. A down comer with an internal diameter of 10 mm has been installed at the centre of the debris bed. The debris bed is built up in a cylindrical crucible with an inner diameter of 125 mm. The bed of height 640 mm is composed of polydispersed particles with particle diameters 2, 3 and 6 mm. Since the long term coolability of such particle bed is limited by the availability of coolant inside the bed and not by heat transfer limitations from the particles to the coolant, the bottom inflow of water improves the coolability of the debris bed and an increase of the dryout heat flux can be observed. With increasing system pressure, the coolability limits are enhanced (increased dryout heat flux).

Geminicoccus roseus gen. nov., sp. nov., an aerobic phototrophic Alphaproteobacterium isolated from a marine aquaculture biofilter

DEFF Research Database (Denmark)

Foesel, Bärbel U.; Gößner, Anita S.; Drake, Harold L.

2007-01-01

A Gram-negative, strictly aerobic, diplococcoid bacterium (strain D2-3T) was isolated from the biofilter of a recirculating marine aquaculture system. Phylogenetic analysis of the 16S rRNA gene sequence of D2-3T indicated that the new organism occupied a novel lineage within the α-1 subclass...... of the DNA was 60.3±0.1 mol%. Phylogenetic, morphological, physiological, and biochemical analyses demonstrated that D2-3T represented a new aerobic phototrophic genus, for which the name Geminicoccus roseus gen. nov., sp. nov. is proposed for the type species (D2-3T=DSM 18922T=ATCC BAA-1445T)....

The choice behaviour of pigs in a Y maze: effects of deprivation of feed, social contact and bedding.

Science.gov (United States)

Hemsworth, Paul H; Smith, Kenneth; Karlen, Marcus G; Arnold, Naomi A; Moeller, Steven J; Barnett, John L

2011-06-01

We examined effects of deprivation of feed, social contact and bedding on the choice behaviour in Y maze tests. Eighty pigs were used to study two main effects: feed (estimated voluntary feed intake (VFI) vs. 70% VFI) and bedding (presence vs. absence), experiment 1; social contact (full vs. restricted) and bedding (presence vs. absence), experiment 2; and feed (as in experiment 1) and social contact (as in experiment 2), experiment 3. Overall pigs consistently chose feed and social contact over bedding. While social contact was more preferred than feed in experiment 3, there was substantial variation between pigs in their choice behaviour. The overall choice behaviour in experiment 3 contradicts previous research, but differences such as the preference methodology as well as the level of deprivation, level of reward and cost involved in accessing reward, may be responsible. Average daily weight gain (ADG) was affected in experiment 3: both feed and social restriction reduced ADG. While the feed effect is expected, one interpretation of the social effect is that social deprivation, through stress, may have reduced ADG. These results provide limited support for the notion that deprivation of a highly preferred resource may disrupt biological function. Copyright © 2011 Elsevier B.V. All rights reserved.

Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

International Nuclear Information System (INIS)

Connolly, J.R.; Keil, K.; Mansker, W.L.; Allen, C.C.; Husler, J.; Lowy, R.; Fortney, D.R.; Lappin, A.R.

1984-10-01

This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworked zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain

Bed Bug Myths

Science.gov (United States)

Learn the truth about bed bugs, such as how easy they are to see with the naked eye, their preferred habitat, whether they transmit diseases, their public health effects, and whether pesticides are the best way to deal with an infestation.

On partial fluidization in rotating fluidized beds

International Nuclear Information System (INIS)

Kao, J.; Pfeffer, R.; Tardos, G.I.

1987-01-01

In a rotating fluidized bed, unlike in a conventional fluidized bed, the granules are fluidized layer by layer from the (inner) free surface outward at increasing radius as the gas velocity is increased. This is a very significant and interesting phenomenon and is extremely important in the design of these fluidized beds. The phenomenon was first suggested in a theoretical analysis and recently verified experimentally in the authors' laboratory. However, in the first paper, the equations presented are too cumbersome and the influence of bed thickness is not clearly stated. In this note the authors present simplified equations, based on that paper, for the pressure drop and the minimum fluidizing velocities in a rotating fluidized bed. Experimental data are also shown and compared with the theoretical model, and the effect of bed thickness is shown. Furthermore, an explanation for the observation of a maximum in the pressure drop vs. velocity curve instead of the plateau derived by Chen is proposed

Tritium measurement technique using ''in-bed'' calorimetry

International Nuclear Information System (INIS)

Klein, J.E.; Mallory, M.K.; Nobile, A. Jr.

1991-01-01

One of the new technologies that has been introduced to the Savannah River Site (SRS) is the production scale use of metal hydride technology to store, pump, and compress hydrogen isotopes. For tritium stored in metal hydride storage beds, a unique relationship does not exist between the amount of tritium in the bed and the pressure-volume-temperature properties of the hydride material. Determining the amount of tritium in a hydride bed after desorbing the contents of the bed to a tank and performing pressure, volume, temperature, and composition (PVTC) measurements is not practical due to long desorption/absorption times and the inability to remove tritium ''heels'' from the metal hydride materials under normal processing conditions. To eliminate the need to remove tritium from hydride storage beds for measurement purposes, and ''in-bed'' tritium calorimetric measurement technique has been developed. The steady-state temperature rise of a gas stream flowing through a jacketed metal hydride storage bed is measured and correlated with power input to electric heaters used to simulate the radiolytic power generated by the decay of tritium to 3 He. Temperature rise results for prototype metal hydride storage beds and the effects of using different gases in the bed are shown. Linear regression results shows that for 95% confidence intervals, temperature rise measurements can be obtained in 14 hours and have an accuracy of ±1.6% of a tritium filled hydride storage bed

The Effects of Long Duration Bed Rest on Functional Mobility and Balance: Relationship to Resting State Motor Cortex Connectivity

Science.gov (United States)

Erdeniz, B.; Koppelmans, V.; Bloomberg, J. J.; Kofman, I. S.; DeDios, Y. E.; Riascos-Castaneda, R. F.; Wood, S. J.; Mulavara, A. P.; Seidler, R. D.

2014-01-01

NASA offers researchers from a variety of backgrounds the opportunity to study bed rest as an experimental analog for space flight. Extended exposure to a head-down tilt position during long duration bed rest can resemble many of the effects of a low-gravity environment such as reduced sensory inputs, body unloading and increased cephalic fluid distribution. The aim of our study is to a) identify changes in brain function that occur with prolonged bed rest and characterize their recovery time course; b) assess whether and how these changes impact behavioral and neurocognitive performance. Thus far, we completed data collection from six participants that include task based and resting state fMRI. The data have been acquired through the bed rest facility located at the University of Texas Medical Branch (Galveston, TX). Subjects remained in bed with their heads tilted down 6 degrees below their feet for 70 consecutive days. Behavioral measures and neuroimaging assessments were obtained at seven time points: a) 7 and 12 days before bed rest; b) 7, 30, and 65 days during bed rest; and c) 7 and 12 days after bed rest. Functional connectivity magnetic resonance imaging (FcMRI) analysis was performed to assess the connectivity of motor cortex in and out of bed rest. We found a decrease in motor cortex connectivity with vestibular cortex and the cerebellum from pre bed rest to in bed rest. We also used a battery of behavioral measures including the functional mobility test and computerized dynamic posturography collected before and after bed rest. We will report the preliminary results of analyses relating brain and behavior changes. Furthermore, we will also report the preliminary results of a spatial working memory task and vestibular stimulation during in and out of bed rest.

Exercise countermeasures for bed-rest deconditioning

Science.gov (United States)

Greenleaf, John (Editor)

1993-01-01

The purpose for this 30-day bed rest study was to investigate the effects of short-term, high intensity isotonic and isokinetic exercise training on maintenance of working capacity (peak oxygen uptake), muscular strength and endurance, and on orthostatic tolerance, posture and gait. Other data were collected on muscle atrophy, bone mineralization and density, endocrine analyses concerning vasoactivity and fluid-electrolyte balance, muscle intermediary metabolism, and on performance and mood of the subjects. It was concluded that: The subjects maintained a relatively stable mood, high morale, and high esprit de corps throughout the study. Performance improved in nearly all tests in almost all the subjects. Isotonic training, as opposed to isokinetic exercise training, was associated more with decreasing levels of psychological tension, concentration, and motivation; and improvement in the quality of sleep. Working capacity (peak oxygen uptake) was maintained during bed rest with isotonic exercise training; it was not maintained with isokinetic or no exercise training. In general, there was no significant decrease in strength or endurance of arm or leg muscles during bed rest, in spite of some reduction in muscle size (atrophy) of some leg muscles. There was no effect of isotonic exercise training on orthostasis, since tilt-table tolerance was reduced similarly in all three groups following bed rest. Bed rest resulted in significant decreases of postural stability and self-selected step length, stride length, and walking velocity, which were not influenced by either exercise training regimen. Most pre-bed rest responses were restored by the fourth day of recovery.

Decreasing ventromedial prefrontal cortex deactivation in risky decision making after simulated microgravity: effects of −6° head-down tilt bed rest

Science.gov (United States)

Rao, Li-Lin; Zhou, Yuan; Liang, Zhu-Yuan; Rao, Henyi; Zheng, Rui; Sun, Yan; Tan, Cheng; Xiao, Yi; Tian, Zhi-Qiang; Chen, Xiao-Ping; Wang, Chun-Hui; Bai, Yan-Qiang; Chen, Shan-Guang; Li, Shu

2014-01-01

Space is characterized by risk and uncertainty. As humans play an important role in long-duration space missions, the ability to make risky decisions effectively is important for astronauts who spend extended time periods in space. The present study used the Balloon Analog Risk Task to conduct both behavioral and fMRI experiments to evaluate the effects of simulated microgravity on individuals' risk-taking behavior and the neural basis of the effect. The results showed that participants' risk-taking behavior was not affected by bed rest. However, we found that the ventromedial prefrontal cortex (VMPFC) showed less deactivation after bed rest and that the VMPFC activation in the active choice condition showed no significant difference between the win outcome and the loss outcome after bed rest, although its activation was significantly greater in the win outcome than in the loss outcome before bed rest. These results suggested that the participants showed a decreased level of value calculation after the bed rest. Our findings can contribute to a better understanding of the effect of microgravity on individual higher-level cognitive functioning. PMID:24904338

The effect of self-leveling on debris bed coolability under severe accident conditions

Energy Technology Data Exchange (ETDEWEB)

Basso, S.; Konovalenko, A. [Division of Nuclear Power Safety, Royal Institute of Technology (KTH), Roslagstullsbacken 21, D5, Stockholm 106 91 (Sweden); Yakush, S.E. [Institute for Problems in Mechanics of the Russian Academy of Sciences, Ave. Vernadskogo 101 Bldg 1, Moscow 119526 (Russian Federation); Kudinov, P. [Division of Nuclear Power Safety, Royal Institute of Technology (KTH), Roslagstullsbacken 21, D5, Stockholm 106 91 (Sweden)

2016-08-15

Highlights: • A model for coolability of a self-leveling, variable-shape debris bed is proposed. • Sensitivity analysis is performed to screen out the less influential input parameters. • A small fraction of scenarios has initially a non-coolable debris bed configuration. • The fraction of non-coolable scenarios decreases with time due to self-leveling. - Abstract: Nordic-type boiling water reactors employ melt fragmentation, quenching, and long term cooling of the debris bed in a deep pool of water under the reactor vessel as a severe accident (SA) mitigation strategy. The height and shape of the bed are among the most important factors that determine if decay heat can be removed from the porous debris bed by natural circulation of water. The debris bed geometry depends on its formation process (melt release, fragmentation, sedimentation and settlement on the containment basemat), but it also changes with time afterwards, due to particle redistribution promoted by coolant flow (self-leveling). The ultimate goal of this work is to develop an approach to the assessment of the probability that debris in such a variable-shape bed can reach re-melting (which means failure of SA mitigation strategy), i.e. the time necessary for the slumping debris bed to reach a coolable configuration is larger than the time necessary for the debris to reach the re-melting temperature. For this purpose, previously developed models for particulate debris spreading by self-leveling and debris bed dryout are combined to assess the time necessary to reach a coolable state and evaluate its uncertainty. Sensitivity analysis was performed to screen out less important input parameters, after which Monte Carlo simulation was carried out in order to collect statistical characteristics of the coolability time. The obtained results suggest that, given the parameters ranges typical of Nordic BWRs, only a small fraction of debris beds configurations exhibits the occurrence of dryout. Of the

Numerical study of propagation effects in a wireless mesh test bed

CSIR Research Space (South Africa)

Lysko, AA

2008-07-01

Full Text Available The present layout of the indoor wireless mesh network test-bed build at the Meraka Institute is introduced. This is followed by a description of a numerical electromagnetic model for the complete test-bed, including the coupling and diffraction...

Bedding material affects mechanical thresholds, heat thresholds and texture preference

Science.gov (United States)

Moehring, Francie; O’Hara, Crystal L.; Stucky, Cheryl L.

2015-01-01

It has long been known that the bedding type animals are housed on can affect breeding behavior and cage environment. Yet little is known about its effects on evoked behavior responses or non-reflexive behaviors. C57BL/6 mice were housed for two weeks on one of five bedding types: Aspen Sani Chips® (standard bedding for our institute), ALPHA-Dri®, Cellu-Dri™, Pure-o’Cel™ or TEK-Fresh. Mice housed on Aspen exhibited the lowest (most sensitive) mechanical thresholds while those on TEK-Fresh exhibited 3-fold higher thresholds. While bedding type had no effect on responses to punctate or dynamic light touch stimuli, TEK-Fresh housed animals exhibited greater responsiveness in a noxious needle assay, than those housed on the other bedding types. Heat sensitivity was also affected by bedding as animals housed on Aspen exhibited the shortest (most sensitive) latencies to withdrawal whereas those housed on TEK-Fresh had the longest (least sensitive) latencies to response. Slight differences between bedding types were also seen in a moderate cold temperature preference assay. A modified tactile conditioned place preference chamber assay revealed that animals preferred TEK-Fresh to Aspen bedding. Bedding type had no effect in a non-reflexive wheel running assay. In both acute (two day) and chronic (5 week) inflammation induced by injection of Complete Freund’s Adjuvant in the hindpaw, mechanical thresholds were reduced in all groups regardless of bedding type, but TEK-Fresh and Pure-o’Cel™ groups exhibited a greater dynamic range between controls and inflamed cohorts than Aspen housed mice. PMID:26456764

Effects of alternative deep bedding options on dairy cow preference, lying behavior, cleanliness, and teat end contamination.

Science.gov (United States)

Wolfe, T; Vasseur, E; DeVries, T J; Bergeron, R

2018-01-01

Cows spend more time lying down when stalls are soft and dry, and bedding plays a key role in the comfort of the lying surface. The first objective of this study (experiment 1) was to compare cow preference for 2 types of alternative deep-bedding materials, switchgrass and switchgrass-lime, using wheat straw on a rubber mat as a control. Nine Holstein lactating cows were submitted in trios to a 3-choice preference test over 14 d (2 d of adaptation, 3 d of restriction to each stall, and 3 d of free access to all 3 stalls). Cows were housed individually in pens containing 3 stalls with different lying surfaces: (1) rubber mat with chopped wheat straw (WS); (2) deep-bedded switchgrass (SG); and (3) deep-bedded switchgrass, water, and lime mixture (SGL). The second objective (experiment 2) was to test, in freestall housing, the effects of these 3 types of bedding on lying behavior, cow cleanliness, and teat end bacterial contamination. Bedding treatments were compared in a 3 × 3 Latin square design using 24 cows split into groups of 8, with bedding materials being switched every 4 wk. Lying behavior was measured with data loggers in both studies. During experiment 1, cows chose to spend more time lying and had more frequent lying bouts on SG (9.4 h/d; 8.2 bouts/d) than on SGL (1.0 h/d; 0.9 bouts/d). They also spent more time standing and stood more frequently in stalls with SG (2.0 h/d; 10.1 bouts/d) than in those with SGL (0.6 h/d; 2.6 bouts/d), and stood longer in stalls with SG than with WS (0.6 h/d). In experiment 2, the total lying time, frequency of lying bouts, and mean lying bout duration were, on average, 9.7 ± 1.03 h/d, 8.2 ± 0.93 bouts/d, and 1.2 ± 0.06 h/bout, respectively, and did not differ between treatments. No treatment effects were found for cow cleanliness scores. Bedding dry matter was highest for SG (74.1%), lowest for SGL (63.5%), and intermediate for WS (68.6%) [standard error of the mean (SEM) = 1.57%]. This may explain the higher teat end

Simulation of a high efficiency multi-bed adsorption heat pump

International Nuclear Information System (INIS)

TeGrotenhuis, W.E.; Humble, P.H.; Sweeney, J.B.

2012-01-01

Attaining high energy efficiency with adsorption heat pumps is challenging due to thermodynamic losses that occur when the sorbent beds are thermally cycled without effective heat recuperation. The multi-bed concept described here enables high efficiency by effectively transferring heat from beds being cooled to beds being heated. A simplified lumped-parameter model and detailed finite element analysis are used to simulate a sorption compressor, which is used to project the overall heat pump coefficient of performance. Results are presented for ammonia refrigerant and a nano-structured monolithic carbon sorbent specifically modified for the application. The effects of bed geometry and number of beds on system performance are explored, and the majority of the performance benefit is obtained with four beds. Results indicate that a COP of 1.24 based on heat input is feasible at AHRI standard test conditions for residential HVAC equipment. When compared on a basis of primary energy input, performance equivalent to SEER 13 or 14 are theoretically attainable with this system. - Highlights: ► A multi-bed concept for adsorption heat pumps is capable of high efficiency. ► Modeling is used to simulate sorption compressor and overall heat pump performance. ► Results are presented for ammonia refrigerant and a nano-structured monolithic carbon sorbent. ► The majority of the efficiency benefit is obtained with four beds. ► Predicted COP as high as 1.24 for cooling is comparable to SEER 13 or 14 for electric heat pumps.

Particle Bed Reactor scaling relationships

International Nuclear Information System (INIS)

Slovik, G.; Araj, K.; Horn, F.L.; Ludewig, H.; Benenati, R.

1987-01-01

Scaling relationships for Particle Bed Reactors (PBRs) are discussed. The particular applications are short duration systems, i.e., for propulsion or burst power. Particle Bed Reactors can use a wide selection of different moderators and reflectors and be designed for such a wide range of power and bed power densities. Additional design considerations include the effect of varying the number of fuel elements, outlet Mach number in hot gas channel, etc. All of these variables and options result in a wide range of reactor weights and performance. Extremely light weight reactors (approximately 1 kg/MW) are possible with the appropriate choice of moderator/reflector and power density. Such systems are very attractive for propulsion systems where parasitic weight has to be minimized

Effect of packing fraction variations on reactivity in pebble-bed reactor

International Nuclear Information System (INIS)

Snoj, L.; Ravnik, M.

2004-01-01

The pebble-bed reactor (PBR) core consists of large number of randomly packed spherical fuel elements. The effect of fuel element packing density variations on multiplication factor in a typical PBR is studied using WIMS code. It is observed that at normal conditions the k-eff increases with packing fraction. Effects of secondary coolant ingress (water or molten lead) in the core at accidental conditions are studied at various packing densities. The effect of water ingress on reactivity depends strongly on water density and packing fraction and is prevailingly positive, while the lead ingress reduces multiplication factor regardless of lead effective density and packing fraction. Both effects are stronger at lower packing fractions. (author)

LBNP/ergometer effects on female cardiovascular and muscle deconditioning in 15d head-down bed rest

Science.gov (United States)

Wang, Lin-Jie

2012-07-01

Female has already been an important part of astronaut corps but gender characteristics in weightlessness and countermeasure effects still not clearly elucidated. In this study the LBNP/Ergometer effects on female cardiovascular deconditioning and muscle atrophy in 15d head-down bed rest were explored. 22 female university students were recruited as volunteers that participated in the 15d head-down bed rest. They were divided into control group (Con,n=8), LBNP exercise group (LBNP,n=7) and LBNP combined with ergometer exercise group (LBNP+Ergo, n=7). Grade negative pressures of -10,-20,-30,-40mmHg 20 or 55min were used in LBNP exercise. In ergometer exercises the subjects must maintain 60-80% VO2peak of pre-bed rest at pedal speed of about 70cycle/min for 15min and the entire exercise duration was 30min. LBNP were performed at 6th,8th,10th,12th,and 13th day and Ergometer were operated at 4th,5th,7th,9th,11th day during bed rest. Before and after bed rest, cardiovascular tilt test were performed to evaluate orthostatic intolerance, supine cycle ergometer were used to test the cardiopulmonary function, MRI tests were operated to examine the volume variations of leg muscle groups and isokinetic test were given to test the muscle strength and endurance of knee. 40% of female subjects did not pass the tilt table test after bed rest and exercises made no difference. Compared with pre-BR, VO2max and VO2max /body weight, VO2/HRmax, maximal power and duration significantly decreased in CON group and LBNP group. For the ERGO+LBNP group, there were no visible different in the parameters of cardiopulmonary function except that maximal power and duration decreased. Muscle maximal voluntary contraction and muscle (quadriceps, rectus femoris, gastrocnemius and soleus) volume decreasing in non-predominant leg was larger in Con group than in LBNP+Ergo group. It is suggested that LBNP combined with ergometer in some degrees can counteract the cardiovascular and muscle deconditioning

Effects of magnetic fields on improving mass transfer in flue gas desulfurization using a fluidized bed

Science.gov (United States)

Zhang, Qi; Gui, Keting; Wang, Xiaobo

2016-02-01

The effects of magnetic fields on improving the mass transfer in flue gas desulfurization using a fluidized bed are investigated in the paper. In this research, the magnetically fluidized bed (MFB) is used as the reactor in which ferromagnetic particles are fluidized with simulated flue gas under the influence of an external magnetic field. Lime slurry is continuously sprayed into the reactor. As a consequence, the desulfurization reaction and the slurry drying process take place simultaneously in the MFB. In this paper, the effects of ferromagnetic particles and external magnetic fields on the desulphurization efficiency are studied and compared with that of quartz particles as the fluidized particles. Experimental results show that the ferromagnetic particles not only act as a platform for lime slurry to precipitate on like quartz particles, but also take part in the desulfurization reaction. The results also show that the specific surface area of ferromagnetic particles after reaction is enlarged as the magnetic intensity increases, and the external magnetic field promotes the oxidation of S(IV), improving the mass transfer between sulphur and its sorbent. Hence, the efficiency of desulphurization under the effects of external magnetic fields is higher than that in general fluidized beds.

Maternal and individual effects in selection of bed sites and their consequences for fawn survival at different spatial scales.

Science.gov (United States)

Van Moorter, Bram; Gaillard, Jean-Michel; McLoughlin, Philip D; Delorme, Daniel; Klein, François; Boyce, Mark S

2009-03-01

We examined the relationship between survival of roe deer (Capreolus capreolus) fawns at Trois Fontaines, Champagne-Ardennes, France, and factors related to bed-site selection (predator avoidance and thermoregulation) and maternal food resources (forage availability in the maternal home range). Previous studies have demonstrated that at small scales, the young of large herbivores select bed sites independently from their mothers, although this selection takes place within the limits of their mother's home range. Fawn survival was influenced largely by the availability of good bed sites within the maternal home range, not by the fawn's selection of bed sites; however, selection for thermal cover when selecting bed sites positively influenced survival of young fawns. Typical features of a good home range included close proximity to habitat edges, which is related to forage accessibility for roe deer. The availability of bed sites changed as fawns aged, probably due to an increased mobility of the fawn or a different use of the home range by the mother; sites offering high concealment and thermal protection became less available in favor of areas with higher forage accessibility. Despite the minor influence of bed-site selection on survival, roe deer fawns strongly selected their bed sites according to several environmental factors linked to predator avoidance and thermoregulation. Fawns selected for sites providing concealment, light penetration, and avoided signs of wild boar (Sus scrofa) activity. Avoidance of sites with high light penetration by young fawns positively affected their survival, confirming a negative effect on thermoregulation due to reduced thermal cover. Selection for light penetration by older fawns was less clear. We discuss these results in the context of cross-generational effects in habitat selection across multiple scales, and the potential influence of the 'ghost of predation past'.

Zebra mussel beds: an effective feeding ground for Ponto-Caspian gobies or suitable shelter for their prey?

Science.gov (United States)

Kobak, Jarosław; Poznańska, Małgorzata; Jermacz, Łukasz; Kakareko, Tomasz; Prądzynski, Daniel; Łodygowska, Małgorzata; Montowska, Karolina; Bącela-Spychalska, Karolina

2016-01-01

Aggregations of the Ponto-Caspian invasive zebra mussel ( Dreissena polymorpha ) constitute a suitable habitat for macroinvertebrates, considerably increasing their abundance and providing effective antipredator protection. Thus, the overall effect of a mussel bed on particular predator species may vary from positive to negative, depending on both prey density increase and predator ability to prey in a structurally complex habitat. Alien Ponto-Caspian goby fish are likely to be facilitated when introduced into new areas by zebra mussels, provided that they are capable of utilizing mussel beds as habitat and feeding grounds. We ran laboratory experiments to find which prey (chironomid larvae) densities (from ca. 500 to 2,000 individuals m -2 ) in a mussel bed make it a more beneficial feeding ground for the racer goby Babka gymnotrachelus (RG) and western tubenose goby Proterorhinus semilunaris (WTG) compared to sandy and stone substrata (containing the basic prey density of 500 ind. m -2 ). Moreover, we checked how food availability affects habitat selection by fish. Mussel beds became more suitable for fish than alternative mineral substrata when food abundance was at least two times higher (1,000 vs. 500 ind. m -2 ), regardless of fish size and species. WTG was associated with mussel beds regardless of its size and prey density, whereas RG switched to this habitat when it became a better feeding ground than alternative substrata. Larger RG exhibited a stronger affinity for mussels than small individuals. WTG fed more efficiently from a mussel bed at high food abundances than RG. A literature review has shown that increasing chironomid density, which in our study was sufficient to make a mussel habitat an attractive feeding ground for the gobies, is commonly observed in mussel beds in the field. Therefore, we conclude that zebra mussels may positively affect the alien goby species and are likely to facilitate their establishment in novel areas, contributing to an

Zebra mussel beds: an effective feeding ground for Ponto-Caspian gobies or suitable shelter for their prey?

Directory of Open Access Journals (Sweden)

Jarosław Kobak

2016-11-01

Full Text Available Aggregations of the Ponto-Caspian invasive zebra mussel (Dreissena polymorpha constitute a suitable habitat for macroinvertebrates, considerably increasing their abundance and providing effective antipredator protection. Thus, the overall effect of a mussel bed on particular predator species may vary from positive to negative, depending on both prey density increase and predator ability to prey in a structurally complex habitat. Alien Ponto-Caspian goby fish are likely to be facilitated when introduced into new areas by zebra mussels, provided that they are capable of utilizing mussel beds as habitat and feeding grounds. We ran laboratory experiments to find which prey (chironomid larvae densities (from ca. 500 to 2,000 individuals m−2 in a mussel bed make it a more beneficial feeding ground for the racer goby Babka gymnotrachelus (RG and western tubenose goby Proterorhinus semilunaris (WTG compared to sandy and stone substrata (containing the basic prey density of 500 ind. m−2. Moreover, we checked how food availability affects habitat selection by fish. Mussel beds became more suitable for fish than alternative mineral substrata when food abundance was at least two times higher (1,000 vs. 500 ind. m−2, regardless of fish size and species. WTG was associated with mussel beds regardless of its size and prey density, whereas RG switched to this habitat when it became a better feeding ground than alternative substrata. Larger RG exhibited a stronger affinity for mussels than small individuals. WTG fed more efficiently from a mussel bed at high food abundances than RG. A literature review has shown that increasing chironomid density, which in our study was sufficient to make a mussel habitat an attractive feeding ground for the gobies, is commonly observed in mussel beds in the field. Therefore, we conclude that zebra mussels may positively affect the alien goby species and are likely to facilitate their establishment in novel areas

Effect of bedding control on amount of house dust mite allergens, asthma symptoms, and peak expiratory flow rate.

Science.gov (United States)

Lee, Inn-Sook

2003-04-30

This quasi-experimental study was designed to investigate the effect of bedding control on the amount of house dust mite (HDM) allergens, asthma symptoms, and peak expiratory flow rate (PEFR) in asthmatics sensitive to HDMs. The subjects in the study were drawn from patients receiving treatment at the allergy clinics of three university-affiliated hospitals in Seoul. Forty-two patients without prior practice of the bedding control used in this study were selected. They commonly showed bronchial asthma caused by HDMs, and exhibited strong positive points (more than 3 points) in skin prick test (D. farinae, D. pteronyssinus), and positive response in both fluoro-allergosorbent test (FAST), and PC20 methacholine test. Of the subjects, alternatively, 22 were assigned to the experimental group and 20 to control group. Bedding control consisted of the use of outer cotton covers, boiling them for 10 minutes fortnightly, and disinfecting bedding by sunlight fortnightly. The experimental group was under bedding control for 4 weeks. The data were collected from October 2000 to January 2001. The results were as follows: 1. After bedding control, the total amount of HDM allergens decreased significantly in the experimental group. However there was no significant difference in the decrease of the amount of HDM allergens between the two groups. 2. Of the asthma symptoms, there was significant difference only in the decrease of the frequency of dyspnea, and in the increase of sleeping disturbance between the two groups after bedding control. 3. After bedding control, PEFR increased in the experimental group whereas it decreased in the control group. However, neither change was significant. The above findings indicate that bedding control improved several asthma symptoms in asthmatics sensitive to HDMs. Accordingly, we suggest that bedding control is adopted as a useful nursing intervention in the field.

Flue Gas Emissions from Fluidized Bed Combustion

NARCIS (Netherlands)

Bramer, E.A.; Valk, M.

1995-01-01

During the past decades fluidized bed coal combustion was developed as a technology for burning coal in an effective way meeting the standards for pollution control. During the earlier years of research on fluidized bed combustion, the potential for limiting the S02 emission by adding limestone to

The influence of fine char particles burnout on bed agglomeration during the fluidized bed combustion of a biomass fuel

Energy Technology Data Exchange (ETDEWEB)

Scala, Fabrizio; Chirone, Riccardo [Istituto di Ricerche sulla Combustione, CNR, P.le V. Tecchio, 80-80125 Naples (Italy); Salatino, Piero [Dipartimento di Ingegneria Chimica, Universita degli Studi di Napoli Federico II, P.le V. Tecchio, 80-80125 Naples (Italy)

2003-11-15

The combustion of biomass char in a bubbling fluidized bed is hereby addressed, with specific reference to the influence that the combustion of fine char particles may exert on ash deposition and bed agglomeration phenomena. Experiments of steady fluidized bed combustion (FBC) of powdered biomass were carried out with the aim of mimicking the postcombustion of attrited char fines generated in the fluidized bed combustion of coarse char. Experimental results showed that the char elutriation rate is much smaller than expected on the basis of the average size of the biomass powder and of the carbon loading in the combustor. Samples of bed material collected after prolonged operation of the combustor were characterized by scanning electron microscopy (SEM)-EDX analysis and revealed the formation of relatively coarse sand-ash-carbon aggregates. The phenomenology is consistent with the establishment of a char phase attached to the bed material as a consequence of adhesion of char fines onto the sand particles. Combustion under sound-assisted fluidization conditions was also tested. As expected, enhancement of fines adhesion on bed material and further reduction of the elutriation rate were observed. Experimental results are interpreted in the light of a simple model which accounts for elutriation of free fines, adhesion of free fines onto bed material and detachment of attached fines by attrition of char-sand aggregates. Combustion of both free and attached char fines is considered. The parameters of the model are assessed on the basis of the measured carbon loadings and elutriation rates. Model computations are directed to estimate the effective size and the peak temperature of char-sand aggregates. The theoretical estimates of the effective aggregate size match fairly well those observed in the experiments.

COOLOCE debris bed experiments and simulations investigating the coolability of cylindrical beds with different materials and flow modes

Energy Technology Data Exchange (ETDEWEB)

Takasuo, E.; Kinnunen, T.; Holmstroem, S.; Lehtikuusi, T. [VTT Technical Research Centre of Finland (Finland)

2013-07-15

The COOLOCE experiments aim at investigating the coolability of debris beds of different geometries, flow modes and materials. A debris bed may be formed of solidified corium as a result of a severe accident in a nuclear power reactor. The COOLOCE-8 test series consisted of experiments with a top-flooded test bed with irregular gravel as the simulant material. The objective was to produce comparison data useful in estimating the effects of different particle materials and the possible effect of the test arrangement on the results. It was found that the dryout heat flux (DHF) measured for the gravel was lower compared to previous experiments with spherical beads, and somewhat lower compared to the early STYX experiments. The difference between the beads and gravel is at least partially explained by the smaller average size of the gravel particles. The COOLOCE-9 test series included scoping experiments examining the effect of subcooling of the water pool in which the debris bed is immersed. The experiments with initially subcooled pool suggest that the subcooling may increase DHF and increase coolability. The aim of the COOLOCE-10 experiments was to investigate the effect of lateral flooding on the DHF a cylindrical test bed. The top of the test cylinder and its sidewall were open to water infiltration. It was found that the DHF is increased compared to a top-flooded cylinder by more than 50%. This suggests that coolability is notably improved. 2D simulations of the top-flooded test beds have been run with the MEWA code. Prior to the simulations, the effective particle diameter for the spherical beads and the irregular gravel was estimated by single-phase pressure loss measurements performed at KTH in Sweden. Parameter variations were done for particle size and porosity used as input in the models. It was found that with the measured effective particle diameter and porosity, the simulation models predict DHF with a relatively good accuracy in the case of spherical

Fluidization bed coating of copper bars with epoxy powder

OpenAIRE

Soh, Chiaw Min

2014-01-01

Fluidized bed coating (FBC) is a process where preheated material is dipped into a flowing liquid bed of powder. Although FBC has existed for more than half a century, however there is little knowledge about the fluidized bed design that gives excellent fluidization quality as well as reducing powder entrainment. The objectives of this thesis are to investigate the effect of two different types of distributor with different pressure drop on powder coating, hydrodynamics of fluidized bed coati...

Udder health in a Danish compost bedded pack barn

OpenAIRE

Svennesen, Line; Enevoldsen, Carsten; Bjerg, Bjarne Schmidt; Klaas, Ilka Christine

2014-01-01

Besides welfare advantages of the compost bedded pack system (CBP) there could be a negative effect of the organic bedding on udder health. Our objectives were to evaluate the effects of a CBP on udder health compared to a free stall system (FS) with sand bedded cubicles. Within the same Danish organic farm, 330 multiparous cows were randomly allocated to CBP or FS. During the experimental period (EP), December 2012 to May 2013, proportions of cows with blinded teats were registered monthly a...

Public hospital bed crisis: too few or too misused?

Science.gov (United States)

Scott, Ian A

2010-08-01

* Increasing demand on public hospital beds has led to what many see as a hospital bed crisis requiring substantial increases in bed numbers. By 2050, if current bed use trends persist and as the numbers of frail older patients rise exponentially, a 62% increase in hospital beds will be required to meet expected demand, at a cost almost equal to the entire current Australian healthcare budget. * This article provides an overview of the effectiveness of different strategies for reducing hospital demand that may be viewed as primarily (although not exclusively) targeting the hospital sector - increasing capacity and throughput and reducing readmissions - or the non-hospital sector - facilitating early discharge or reducing presentations and admissions to hospital. Evidence of effectiveness was retrieved from a literature search of randomised trials and observational studies using broad search terms. * The principal findings were as follows: (1) within the hospital sector, throughput could be substantially improved by outsourcing public hospital clinical services to the private sector, undertaking whole-of-hospital reform of care processes and patient flow that address both access and exit block, separating acute from elective beds and services, increasing rates of day-only or short stay admissions, and curtailing ineffective or marginally effective clinical interventions; (2) in regards to the non-hospital sector, potentially the biggest gains in reducing hospital demand will come from improved access to residential care, rehabilitation services, and domiciliary support as patients awaiting such services currently account for 70% of acute hospital bed-days. More widespread use of acute care and advance care planning within residential care facilities and population-based chronic disease management programs can also assist. * This overview concludes that, in reducing hospital bed demand, clinical process redesign within hospitals and capacity enhancement of non

Coal-bed methane water: effects on soil properties and camelina productivity

Science.gov (United States)

Every year the production of coal-bed natural gas in the Powder River Basin results in the discharge of large amounts of coal-bed methane water (CBMW) in Wyoming; however, no sustainable disposal methods for CBMW are currently available. A greenhouse study was conducted to evaluate the potential to ...

Evacuation of Bed-bound Patients-STEPS Simulations

DEFF Research Database (Denmark)

Madsen, Anne; Dederichs, Anne Simone

2016-01-01

Fires in hospitals occur, and evacuation of bed-bound patients might be necessary in case of emergency. The current study concerns the evacuation of bed-bound patients from a fire section in a hospital using hospital porters. The simulations are performed using the STEPS program. The aim...... of the study is to investigate the evacuation time of bed-bound hospital patients using different walking speeds from the literature, and the influence of the number of hospital porters on the total evacuation times of bed-bound patients. Different scenarios were carried out with varying staff......-to-patient ratios that simulate the horizontal evacuation of 40 bed-bound patients into a different fire section. It was found that the staff-to-patient-ratio affects the total evacuation times. However, the total evacuation times do not decrease linearly and a saturation effect is seen at a staff-to-patient ratio...

Rats Housed on Corncob Bedding Show Less Slow-Wave Sleep

OpenAIRE

Leys, Laura J; McGaraughty, Steve; Radek, Richard J

2012-01-01

Despite the reported advantages of corncob bedding, questions have emerged about how comfortable animals find this type of bedding as a resting surface. In this study, encephalography (EEG) was used to compare the effects of corncob and aspen-chip bedding on rat slow-wave sleep (SWS). According to a facility-wide initiative, rats that were weaned on aspen-chip bedding were switched to corncob bedding in home cages and EEG recording chambers. Spontaneous EEG recordings obtained for 5 wk after ...

Thermophilic biofiltration of benzene and toluene.

Science.gov (United States)

Cho, Kyung-Suk; Yoo, Sun-Kyung; Ryu, Hee Wook

2007-12-01

In the current studies, we characterized the degradation of a hot mixture of benzene and toluene (BT) gases by a thermophilic biofilter using polyurethane as packing material and high-temperature compost as a microbial source. We also examined the effect of supplementing the biofilter with yeast extract (YE). We found that YE substantially enhanced microbial activity in the thermophilic biofilter. The degrading activity of the biofilter supplied with YE was stable during long-term operation (approximately 100 d) without accumulating excess biomass. The maximum elimination capacity (1,650 g x m(-3) h(-1)) in the biofilter supplemented with YE was 3.5 times higher than that in the biofilter without YE (470 g g x m(-3) h(-1)). At similar retention times, the capacity to eliminate BT for the YE-supplemented biofilter was higher than for previously reported mesophilic biofilters. Thus, thermophilic biofiltration can be used to degrade hydrophobic compounds such as a BT mixture. Finally, 16S rDNA polymerase chain reaction-DGGE (PCR-DGGE) fingerprinting revealed that the thermophilic bacteria in the biofilter included Rubrobacter sp. and Mycobacterium sp.

Numerical simulation for debris bed behavior in sodium cooled fast reactor

International Nuclear Information System (INIS)

Tagami, Hirotaka; Tobita, Yoshiharu

2014-01-01

For safety analysis of SFR, it is necessary to evaluate behavior along with coolability of debris bed in lower plenum which is formed in severe accident. In order to analyze debris behavior, model for dense sediment particles behavior was proposed and installed in SFR safety analysis code SIMMER. SIMMER code could adequately reproduce experimental results simulating the self-leveling phenomena with appropriate model parameters for bed stiffness. In reactor condition, the self-leveling experiment for prototypical debris bed has not been performed. Additionally, the prototypical debris bed consists of non-spherical particles and it is difficult to quantify model parameters. This situation brings sensitivity analysis to investigate effect of model parameters on the self-leveling phenomena of prototypical debris bed in present paper. As initial condition for sensitivity analysis, simple mound-like debris bed in sodium-filled lower plenum in reactor vessel is considered. The bed consists of the mixture of fuel debris of 3,300 kg and steel debris of 1,570 kg. Decay heat is given to this fuel debris. The model parameter is chosen as sensitivity parameter. Sensitivity analysis shows that the model parameters can effect on intensity of self-leveling phenomena and eventual flatness of bed. In all analyses, however, coolant and sodium vapor break the debris bed at mainly center part of bed and the debris is relocated to outside of bed. Through this process, the initial debris bed is almost planarized before re-melting of debris. This result shows that the model parameters affect the self-leveling phenomena, but its effect in the safety analysis of SFRs is limited. (author)

Effective thermal conductivity of advanced ceramic breeder pebble beds

Energy Technology Data Exchange (ETDEWEB)

Pupeschi, S., E-mail: simone.pupeschi@kit.edu; Knitter, R.; Kamlah, M.

2017-03-15

As the knowledge of the effective thermal conductivity of ceramic breeder pebble beds under fusion relevant conditions is essential for the development of solid breeder blanket concepts, the EU advanced and reference lithium orthosilicate material were investigated with a newly developed experimental setup based on the transient hot wire method. The effective thermal conductivity was investigated in the temperature range RT–700 °C. Experiments were performed in helium and air atmospheres in the pressure range 0.12–0.4 MPa (abs.) under a compressive load up to 6 MPa. Results show a negligible influence of the chemical composition of the solid material on the bed’s effective thermal conductivity. A severe reduction of the effective thermal conductivity was observed in air. In both atmospheres an increase of the effective thermal conductivity with the temperature was detected, while the influence of the compressive load was found to be small. A clear dependence of the effective thermal conductivity on the pressure of the filling gas was observed in helium in contrast to air, where the pressure dependence was drastically reduced.

Cooling of an internal-heated debris bed with fine particles

International Nuclear Information System (INIS)

Yang, Z.L.; Sehgal, B.R.

2001-01-01

In this paper, an analytical model on dryout heat flux of ex-vessel debris beds with fines particles under top flooding conditions has been developed. The parametric study is performed on the effect of the stratification of the debris beds on the dryout heat flux. The calculated results show that the stratification configuration of the debris beds with smaller particles and lower porosity layer resting on the top of another layer of the beds has profound effect on the dryout heat flux for the debris beds both with and without a downcomer. The enhancement of the dryout heat flux by the downcomer is significant. The efficiency of the single downcomer on the enhancement of the dryout heat flux is also analyzed. This, in general, agrees well with experimental data. The model is also employed to perform the assessment on the coolability of the ex-vessel debris bed under representative accidental conditions. One conservative case is chosen, and it is found that the downcomer could be efficient measure to cool the debris bed and hence terminate the severe accident. (authors)

Removal of traces of toluene and p-xylene in indoor air using biofiltration and a hybrid system (biofiltration + adsorption).

Science.gov (United States)

Luengas, Angela Tatiana; Hort, Cécile; Platel, Vincent; Elias, Ana; Barona, Astrid; Moynault, Laurent

2017-04-01

Biofiltration technology and the hybrid system combining biofiltration and adsorption (onto activated carbon) were compared as possible methods to toluene and p-xylene at parts per million concentration levels (2-45 and 1-33 ppb, respectively). An organic material was used as packing material for the biofiltration process. Even at low empty bed residence times (EBRTs) and concentrations, toluene removal efficiency reached 100% and p-xylene showed an increasing trend on their removal efficiency over the time using biofiltration. The assessment of by-products and particle generation by the biofilter and the hybrid system were taken into account. Acetone and acetic acid were identified as by-products of the biofilter. Particle emissions in the range of 0.03 to 10 μm were recorded for both systems.

Management bedding : vrijloopstal met composterende bedding van houtsnippers

NARCIS (Netherlands)

Boer, de H.C.; Wiersma, M.; Galama, P.J.; Szanto, G.L.

2015-01-01

In de vrijloopstal liggen de koeien meestal op een organische bedding en scheiden daar mest (feces en urine) uit. Om de bedding voldoende droog en schoon te houden wordt er regelmatig nieuw strooisel aangevoerd en wordt de toplaag bewerkt. Op basis van onderzoek- en praktijkervaringen tot nu toe

Combustion of gases released from peat or biomass in fluidized bed

Energy Technology Data Exchange (ETDEWEB)

Raiko, R. [Tampere Univ. of Technology (Finland). Energy and Process Engineering

1996-12-01

Temperature and gas concentration experiments have been conducted to determine at what temperature carbon monoxide, methane and propane begin to react within the particulate phase of a bubbling fluidized bed. The fluidized bed reactor used in these experiments was a stainless-steel tube with an internal diameter of 50 mm surrounded by an electric heater. Two different natural quartz sands were used (d{sub p} =0.35 mm and 0.6 mm). The bed height used varied between 100 and 260 mm (in unfluidized state). A porous plate distributor, made of kaowool, was used to avoid jets appearing at the distributor. The bed was operated at incipient fluidization (u = 5.9-9 cm/s). The bed temperatures used ranged from 600 deg C to 850 deg C. It was found that carbon monoxide, methane and propane react inside a fluidized bed, but often other conditions than temperature have a considerable effect on the rate of the reaction. The critical temperature was found to be 650 deg C for propane and carbon monoxide and 700 deg C for methane. With under-stoichiometric mixture of carbon monoxide and air the heat release can be over 2.5 MW/m{sup 3} when bed temperature is 650 deg C. According to these experiments it is obvious that the reaction mechanism for carbon monoxide oxidation inside a fluidized bed differs greatly from that of gas phase only. The results of our more than 1300 test runs show clearly the varying effects of the different bed materials. Even with the same bed material totally different results can be obtained. In order to elucidate the possible changes of particle surface, microscopic and porosimetric studies was conducted with both fresh bed particles and used bed particles. Also the effect of commonly used ingredients, like limestone and dolomite, was tested. A global model for carbon monoxide oxidation inside a fluidized bed was introduced. The model was tested against measured data from the laboratory-scale fluidized bed test rig. (Abstract Truncated)

Combustion of peanut shells in a cone-shaped bubbling fluidized-bed combustor using alumina as the bed material

International Nuclear Information System (INIS)

Arromdee, Porametr; Kuprianov, Vladimir I.

2012-01-01

Highlights: ► We propose burning of peanut shells in a conical fluidized bed using alumina sand. ► We examine hydrodynamic, combustion and emission characteristics of the reactor. ► High, over 99%, combustion efficiency is achievable. ► Emissions of CO and NO from the combustor meet the national emission limits. ► Composition of the bed material undergoes significant changes during the combustion. -- Abstract: This paper reports experimental studies on burning peanut shells in the conical fluidized-bed combustor using alumina sand as the fluidizing agent. Prior to combustion tests, hydrodynamic regimes and characteristics of a conical alumina–biomass bed were investigated under cold-state conditions for variable percentage of peanut shells in the mixture and static bed height. With selected particle sizes (300–500 μm) and static bed height (30 cm), alumina ensured bubbling fluidization regime of the bed at operating conditions specified for firing biomass. Combustion tests were performed at 60 kg/h and 45 kg/h fuel feed rates, while ranging excess air from 20% to 80% at a fixed combustor load. Temperature and gas concentrations (O 2 , CO, C x H y as CH 4 , and NO) were measured along radial and axial directions inside the reactor as well as at stack in order to characterize combustion and emission performance of the combustor for the ranges of operating conditions. For firing 60 kg/h peanut shells, excess air of 40% can be selected as an appropriate value ensuring high, about 99%, combustion efficiency and rather low emissions of CO and NO: 520 ppm and 125 ppm, respectively (both on a dry basis and at 6% O 2 ). With reducing combustor load, the combustion efficiency and emission characteristics were improved to a little extent. No evidence of bed agglomeration was found during 30-h combustion tests on this conical fluidized-bed combustor using alumina sand as the bed material. However, the timescale effect on the composition of the bed material was

The effectiveness of various biofiltration substrates in removing bacteria, endotoxins, and dust from ventilation system exhaust from a chicken hatchery.

Science.gov (United States)

Tymczyna, L; Chmielowiec-Korzeniowska, A; Drabik, A

2007-10-01

The objective of this study was to evaluate the effectiveness of various organic and organic-mineral biofilter media in purifying ventilation exhaust from a chicken hatchery room. Three different substrates were tested. Efficiency levels for the removal of dust, gram-negative bacteria, and bacterial endotoxin were recorded. The microbiological properties of the substrates were also studied. All of the biofilter substrates were highly effective in removing gram-negative bacteria, moderately effective in reducing dust levels, and only slightly effective in removing endotoxin. The substrate that was most efficient in retaining bioaerosols was the organic-mineral medium containing 20% halloysite, 40% compost, and 40% peat, which generally had at least satisfactory efficiency values for removing all of the contaminants tested.

Effects of biomass on dynamics of combustion in circulating fluidized beds

Directory of Open Access Journals (Sweden)

Tourunen Antti

2004-01-01

Full Text Available Fluidized bed technology is very suitable for the combustion of biomass Nevertheless substitution of coal with biomass affects boiler operation and especially dynamics and controllability. Non-homogeneity of biomass and fuel feeding disturbances cause process instability, such as variations in temperatures and pressures, which reduce lifetime of equipment and structures. Because of process instability higher air coefficient must be used in order to avoid CO emissions, which is not economical. Combustion profiles for coal, wood and peat, measured at the VTT Processes Pilot circulating fluidized bed reactor, have been compared. Process stability and char inventories have been studied by the measurements and the model. Biofuel are usually very reactive and their combustion profiles are quite different compared to coals. Because of high reactivity and low char content combustion process with biofuel is very sensitive for fuel feeding. Also low char inventory effect on load changes combined with combustion profile that differs from coals. Because of different combustion profile heat transfer can be a limiting factor in load changes despite the high reactivity and fast oxygen response.

Bed retained products in swept fixed bed (SFB) coal hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Mastral, A.M.; Perez-Surio, M.J. [CSIC, Zaragosa (Spain). Inst. de Carboquimica

1997-12-31

The hydropyrolysis of a low rank coal in a swept fixed bed (SFB) reactor is carried out by fixing the hydrogen pressure (40 kg/cm{sup 2}), the hydrogen flow (2 l/min) and the residence time (10 min) at increasing temperatures (400 C, 500 C and 600 C) and coal bed heights (h, 1.5h, 2h, 2.5h and 3h). It is shown that the percentages of tars and char directly depend on the coal bed height and that there is not only a quantitative dependence, but also the height of the coal bed is very important and plays a relevant role on the nature of the conversion products. (orig.)

The NASA Bed Rest Project

Science.gov (United States)

Rhodes, Bradley; Meck, Janice

2005-01-01

NASA s National Vision for Space Exploration includes human travel beyond low earth orbit and the ultimate safe return of the crews. Crucial to fulfilling the vision is the successful and timely development of countermeasures for the adverse physiological effects on human systems caused by long term exposure to the microgravity environment. Limited access to in-flight resources for the foreseeable future increases NASA s reliance on ground-based analogs to simulate these effects of microgravity. The primary analog for human based research will be head-down bed rest. By this approach NASA will be able to evaluate countermeasures in large sample sizes, perform preliminary evaluations of proposed in-flight protocols and assess the utility of individual or combined strategies before flight resources are requested. In response to this critical need, NASA has created the Bed Rest Project at the Johnson Space Center. The Project establishes the infrastructure and processes to provide a long term capability for standardized domestic bed rest studies and countermeasure development. The Bed Rest Project design takes a comprehensive, interdisciplinary, integrated approach that reduces the resource overhead of one investigator for one campaign. In addition to integrating studies operationally relevant for exploration, the Project addresses other new Vision objectives, namely: 1) interagency cooperation with the NIH allows for Clinical Research Center (CRC) facility sharing to the benefit of both agencies, 2) collaboration with our International Partners expands countermeasure development opportunities for foreign and domestic investigators as well as promotes consistency in approach and results, 3) to the greatest degree possible, the Project also advances research by clinicians and academia alike to encourage return to earth benefits. This paper will describe the Project s top level goals, organization and relationship to other Exploration Vision Projects, implementation

Effects of long-term head-down-tilt bed rest and different training regimes on the coagulation system of healthy men.

Science.gov (United States)

Haider, Thomas; Gunga, Hanns-Christian; Matteucci-Gothe, Raffaella; Sottara, Elke; Griesmacher, Andrea; Belavý, Daniel L; Felsenberg, Dieter; Werner, Andreas; Schobersberger, Wolfgang

2013-11-01

Immobility plus preexisting chronic disease or acute trauma can activate the coagulation system, thus increasing the risk for thromboembolic events. The effects of long-term bed-rest immobility and microgravity on the coagulation system of healthy persons (e.g., during crewed Mars missions) have not yet been studied. The main objective of the second Berlin BedRest Study (BBR2-2) "Coagulation Part" was to investigate adaptations of the hemostatic system during long-term bed rest (60 days) under simulated microgravity (6° head-down-tilt [6°HDT]) and after mobilization in three different volunteer groups (randomly assigned to CTR= inactive control group; RE= resistive exercise only group; and RVE= resistive exercise with whole-body vibration group). In 24 males (aged 21-45 years), before, during, and after long-term bed rest, key parameters of coagulation were measured from venous blood samples: D-dimer (DD), thrombin-antithrombin III complex (TAT), and prothrombin fragment F1 + 2 (PT-F1 + 2). Additionally, modified rotational thrombelastometry (ROTEM (®) ) analysis was performed. Times of exploratory analyses were as follows: baseline data collection 2 days before bed rest (BDC-2); eight different days of 6°HDT bed rest (HDT1-HDT60), and two different days after reambulation (R + 3 and R + 6). We found significant changes in DD, TAT, and PT-F1 + 2 over the total time course, but no consistent effect of physical interventions (RE, RVE) on these parameters. Notably, no parameter reached levels indicative of intravascular thrombin formation. All ROTEM® parameters remained within the normal range and no pathological traces were found. Sixty days of 6°HDT bed rest are not associated with pronounced activation of the coagulation system indicative of intravascular thrombus formation in healthy volunteers independent of the training type during the bed rest.

In-bed accountability of tritium in production scale metal hydride storage beds

International Nuclear Information System (INIS)

Klein, J.E.

1995-01-01

An ''in-bed accountability'' (IBA) flowing gas calorimetric measurement method has been developed and implemented to eliminate the need to remove tritium from production scale metal hydride storage beds for inventory measurement purposes. Six-point tritium IBA calibration curves have been completed for two, 390 gram tritium metal hydride storage beds. The calibration curves for the two tritium beds are similar to those obtained from the ''cold'' test program. Tritium inventory errors at the 95 percent confidence level ranged from ± 7.3 to 8.6 grams for the cold test results compared to ± 4.2 to 7.5 grams obtained for the two tritium calibrated beds

The Effects of Long Duration Bed Rest as a Spaceflight Analogue on Resting State Sensorimotor Network Functional Connectivity and Neurocognitive Performance

Science.gov (United States)

Cassady, K.; Koppelmans, V.; Yuan, P.; Cooke, K.; De Dios, Y.; Stepanyan, V.; Szecsy, D.; Gadd, N.; Wood, S.; Reuter-Lorenz, P.;

[Elimination of volatile compounds of leaf tobacco from air emissions using biofiltration].

Science.gov (United States)

Zagustina, N A; Misharina, T A; Vepritskiĭ, A A; Zhukov, V G; Ruzhitskiĭ, A O; Terenina, M B; Krikunova, N I; Kulikova, A K; Popov, V O

2012-01-01

The composition of the volatile organic compounds (VOCs) of various leaf tobacco brands and their blends has been studied. The differences in the content of nicotine, solanone, tetramethyl hexadecenol, megastigmatrienones, and other compounds, determining the specific tobacco smell, have been revealed. A microbial consortium, which is able to deodorize simulated tobacco emissions and decompose nicotine, has been formed by long-term adaptation to the VOCs of tobacco leaves in a laboratory reactor, functioning as a trickle-bed biofilter. Such a biofilter eliminates 90% of the basic toxic compound (nicotine) and odor-active compounds; the filtration efficiency does not change for tobacco brands with different VOC concentrations or in the presence of foreign substances. The main strains, isolated from the formed consortium and participating in the nicotine decomposition process, belong to the genera Pseudomonas, Bacillus, and Rhodococcus. An examination of the biofilter trickling fluid has shown full decomposition of nicotine and odor-active VOCs. The compounds, revealed in the trickling fluid, did not have any odor and were nontoxic. The obtained results make it possible to conduct scaling of the biofiltration process to eliminate odor from air emissions in the tobacco industry.

Biological aspects and ecological effects of a bed of the invasive non-indigenous mussel Brachidontes pharaonis (Fischer P., 1870 in Malta

Directory of Open Access Journals (Sweden)

L. BONNICI

2012-06-01

Full Text Available No mussel beds were known to occur in the Maltese Islands previous to 2009, when a single bed of the Lessepsian immigrant Brachidontes pharaonis, first recorded from the islands in 1970, was discovered in Birzebbugia Bay. The population structure of B. pharaonis was investigated to assess its potential to spread and colonise new shores, while the biotic community at the mussel bed was compared to that present on uncolonised substratum to determine the effects of mussel bed establishment on the associated biota. Results indicate a lower species richness and slightly different community structure with greater small-scale heterogeneity at the mussel bed site compared to the adjacent rocky shore where mussels are present but where there is no bed formation. The B. pharaonis population had a peak density of 16550 ± 2051 ind.m-2 within the mussel bed and included recent recruits. These data suggest that the B. pharaonis population has the potential to expand. Establishment of extensive beds by this invasive mussel could change the structure of native rocky shore assemblages around the Maltese Islands and elsewhere in the Mediterranean.

Fluid bed porosity equation for an inverse fluidized bed bioreactor with particles growing biofilm

International Nuclear Information System (INIS)

Campos-Diaz, K. E.; Limas-Ballesteros, R.

2009-01-01

Fluid Bed Bioreactor performance is strongly affected by bed void fraction or bed porosity fluctuations. Particle size enlargement due to biofilm growth is an important factor that is involved in these variations and until now there are no mathematical equations that consider biofilm growth. In this work a mathematical equation is proposed to calculate bed void fraction in an inverse fluid bed bioreactor. (Author)

Effect of secondary air injection on the combustion efficiency of sawdust in a fluidized bed combustor

Directory of Open Access Journals (Sweden)

K. V. N. Srinivasa Rao

2008-03-01

Full Text Available Agricultural wastes like bagasse, paddy husks, sawdust and groundnut shells can be effectively used as fuels for fluidized bed combustion; otherwise these biomass fuels are difficult to handle due to high moisture and fines content. In the present work the possibility of using sawdust in the fluidized bed combustor, related combustion efficiencies and problems encountered in the combustion process are discussed. The temperature profiles for sawdust with an increase in fluidizing velocity along the vertical height above the distributor plate indicate that considerable burning of fuel particles is taking place in the freeboard zone rather than complete burning within the bed. Therefore, an enlarged disengagement section is provided to improve the combustion of fines. The temperature profiles along the bed height are observed at different feed rates. The feed rate of sawdust corresponding to the maximum possible temperature was observed to be 10.2 kg/h. It is observed that 50-60% excess air is optimal for reducing carbon loss during the burning of sawdust. The maximum possible combustion efficiency with sawdust is 99.2% and is observed with 65% excess air.

Improvement of Combustion Characteristics in Fluidized Bed

International Nuclear Information System (INIS)

Mohamed, H.S.; El Sourougy, M.R.; Faik, M.

2009-01-01

The present investigation is directed towards the experimental study of the effect of a new design of the bed temperature on the overall thermal efficiency and heat transfer by conduction, convection and radiation in gaseous fuel-fluidized bed combustion system. The experiments are performed on a water-cooled fluidized bed model furnace with cylindrical cross-section of 0.25 m diameter and its height is 0.60 m. the fluidising medium used is sand particles with average diameter 1.5 mm. The bed temperature is varied between 700 degree C and 1100 degree C. Measurements f carbon dioxide, carbon monoxide and oxygen concentrations are carried out by using water-cooled sampling probe, and infrared and paramagnetic analyzers. The results obtained show that the bed temperature, the total heat transfer to the wall and the bed combustion efficiency increase with the decrease of the air-fuel ratio. It is also found that 91% of the total heat transfer is in the fluidising part of the bed and most of this heat is transferred by convection from hot sand particles to the wall. Two empirical formulae for the calculation of the wall heat transfer coefficient and the particle convective heat transfer coefficient are proposed. A verification of the proposed empirical formulae is made by comparing the calculated values with the experimental results.

Bed rest and increased diuretic treatment in chronic congestive heart failure

DEFF Research Database (Denmark)

Abildgaard, U; Aldershvile, J; Ring-Larsen, H

1985-01-01

To elucidate the effect of bed rest used as an adjunct to increased diuretic treatment, twelve patients with chronic congestive heart failure (CHF) had a 50% increase in loop diuretic dosage and were allocated to either continuous bed rest or bed rest during nights only. The 24-hour bed rest group...... is a reasonable adjunct to diuretic treatment in patients with CHF....

Effects of head-down-tilt bed rest on cerebral hemodynamics during orthostatic stress

Science.gov (United States)

Zhang, R.; Zuckerman, J. H.; Pawelczyk, J. A.; Levine, B. D.; Blomqvist, C. G. (Principal Investigator)

1997-01-01

Our aim was to determine whether the adaptation to simulated microgravity (microG) impairs regulation of cerebral blood flow (CBF) during orthostatic stress and contributes to orthostatic intolerance. Twelve healthy subjects (aged 24 +/- 5 yr) underwent 2 wk of -6 degrees head-down-tilt (HDT) bed rest to simulate hemodynamic changes that occur when humans are exposed to microG. CBF velocity in the middle cerebral artery (transcranial Doppler), blood pressure, cardiac output (acetylene rebreathing), and forearm blood flow were measured at each level of a ramped protocol of lower body negative pressure (LBNP; -15, -30, and -40 mmHg x 5 min, -50 mmHg x 3 min, then -10 mmHg every 3 min to presyncope) before and after bed rest. Orthostatic tolerance was assessed by using the cumulative stress index (CSI; mmHg x minutes) for the LBNP protocol. After bed rest, each individual's orthostatic tolerance was reduced, with the group CSI decreased by 24% associated with greater decreases in cardiac output and greater increases in systemic vascular resistance at each level of LBNP. Before bed rest, mean CBF velocity decreased by 14, 10, and 45% at -40 mmHg, -50 mmHg, and maximal LBNP, respectively. After bed rest, mean velocity decreased by 16% at -30 mmHg and by 21, 35, and 39% at -40 mmHg, -50 mmHg, and maximal LBNP, respectively. Compared with pre-bed rest, post-bed-rest mean velocity was less by 11, 10, and 21% at -30, -40, and -50 mmHg, respectively. However, there was no significant difference at maximal LBNP. We conclude that cerebral autoregulation during orthostatic stress is impaired by adaptation to simulated microG as evidenced by an earlier and greater fall in CBF velocity during LBNP. We speculate that impairment of cerebral autoregulation may contribute to the reduced orthostatic tolerance after bed rest.

Understanding the fate of organic micropollutants in sand and granular activated carbon biofiltration systems.

Science.gov (United States)

Paredes, L; Fernandez-Fontaina, E; Lema, J M; Omil, F; Carballa, M

2016-05-01

In this study, sand and granular activated carbon (GAC) biofilters were comparatively assessed as post-treatment technologies of secondary effluents, including the fate of 18 organic micropollutants (OMPs). To determine the contribution of adsorption and biotransformation in OMP removal, four reactors were operated (two biofilters (with biological activity) and two filters (without biological activity)). In addition, the influence of empty bed contact time (EBCT), ranging from 0.012 to 3.2d, and type of secondary effluent (anaerobic and aerobic) were evaluated. Organic matter, ammonium and nitrate were removed in both biofilters, being their adsorption higher on GAC than on sand. According to the behaviour exhibited, OMPs were classified in three different categories: I) biotransformation and high adsorption on GAC and sand (galaxolide, tonalide, celestolide and triclosan), II) biotransformation, high adsorption on GAC but low or null adsorption on sand (ibuprofen, naproxen, fluoxetine, erythromycin, roxythromycim, sulfamethoxazole, trimethoprim, bisphenol A, estrone, 17β-estradiol and 17α-ethinylestradiol), and, III) only adsorption on GAC (carbamazepine, diazepam and diclofenac). No influence of EBCT (in the range tested) and type of secondary effluent was observed in GAC reactors, whereas saturation and kinetic limitation of biotransformation were observed in sand reactors. Taking into account that most of the organic micropollutants studied (around 60%) fell into category II, biotransformation is crucial for the elimination of OMPs in sand biofilters. Copyright © 2016 Elsevier B.V. All rights reserved.

Experimental Investigation of Effects of Vibration upon Elastic and Cohesive Properties of Beds of Wet Sand

Directory of Open Access Journals (Sweden)

S. Alsop

1995-01-01

Full Text Available The transmission of sinusoidal vibrations through beds of cohesive particulate solids was measured. Results were interpreted in terms of a critical state model to predict the elastic swelling constant k, and the cohesive stress C. Factorial experimental design was used to identify significant parameters. Factors that affect k include percent moisture, bulk density, sample size, sample shape, the presence of a supporting membrane, and loading order. Factors that affect C include percent moisture and particle size distribution. Factors affecting k were interpreted in terms of their effects upon bed structure and factors affecting C in terms of an equivalent pore water pressure due to capillary and liquid bridge effects. The critical state model was modified to incorporate general relationships between axial and radial strains.

Fundamental Study of Bed Bath Technique : Subjective and Objective Evaluations of Epidermal Effects of Bed Bathing Using Bar Soap and Water-Dissolved Liquid Soap

OpenAIRE

月田, 佳寿美; 竹田, 千佐子; 長谷川, 智子; 白川, かおる

2003-01-01

Purpose: To clarify epidermal effects of bed bathing using bar soap and water-dissolved liquid soap (liquid soap). Method: The subjects were 33 healthy female college students. Subjects' arms were cleaned by two methods, using bar soap and liquid soap. The following objective data were collected from the subjects: skin sebum, moisturization, pH, and feelings of skin conditions (rashes, redness, itchiness, and irritation). Results : 1. Cleansing effects of both methods on oily dirt seemed no d...

Psychological effects of acute physical inactivty during microgravitiy simulated by bed rest

Directory of Open Access Journals (Sweden)

Petra Dolenc

2009-05-01

Full Text Available Long-duration weightlessness simulated by bed rest represents an important model to study the consequences of physical inactivity and sedentarism on the human body. This study evaluated changes of mood status, psychological well-being, coping strategies and physical self in ten healthy young male subjects during a 35-day horizontal bed rest. Participants were asked to complete psychometrical inventories before and after the bed rest experiment. The preceived satisfaction with life and the physical self-concept did not change during bed rest period and mood states were relatively stable during the experiment according to the Emotional States Questionnaire. The neurotic level was enhanced during the bed rest period according to the Slovenian version of the General Health Questionnaire. However, even after the period of physical immobilization, the expression of these symptoms remains relatively low and does not represent a risk to the mental health of the subjects. The results from Coping Resources Inventory indicated a tendency toward an increase of emotion focused coping and a decrease of problem focused coping strategies. The importance of this research was to provide evidence that the provision of favourable habitability countermeasures can prevent deterioration in the psychological state under conditions of physical immobilisation. Our findings have applied value in the field of health prevention and rehabilitaion.

Fluidized bed selective pyrolysis of coal

Science.gov (United States)

Shang, Jer Y.; Cha, Chang Y.; Merriam, Norman W.

1992-01-01

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyzes the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step.

Pebble-bed reactor

International Nuclear Information System (INIS)

Lohnert, G.; Mueller-Frank, U.; Heil, J.

1976-01-01

A pebble-bed nuclear reactor of large power rating comprises a container having a funnel-shaped bottom forming a pebble run-out having a centrally positioned outlet. A bed of downwardly-flowing substantially spherical nuclear fuel pebbles is positioned in the container and forms a reactive nuclear core maintained by feeding unused pebbles to the bed's top surface while used or burned-out pebbles run out and discharge through the outlet. A substantially conical body with its apex pointing upwardly and its periphery spaced from the periphery of the container spreads the bottom of the bed outwardly to provide an annular flow down the funnel-shaped bottom forming the runout, to the discharge outlet. This provides a largely constant downward velocity of the spheres throughout the diameter of the bed throughout a substantial portion of the down travel, so that all spheres reach about the same burned-out condition when they leave the core, after a single pass through the core area

The Safety of Hospital Beds

Science.gov (United States)

Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K.; Bloswick, Donald

2015-01-01

To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients’ ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients’ use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated. PMID:28462302

Fluid-bed combustion

Energy Technology Data Exchange (ETDEWEB)

Hunt, G.; Schoebotham, N.

1981-02-01

In Energy Equipment Company's two-stage fluidized bed system, partial combustion in a fluidized bed is followed by burn-off of the generated gases above the bed. The system can be retrofitted to existing boilers, and can burn small, high ash coal efficiently. It has advantages when used as a hot gas generator for process drying. Tests on a boiler at a Cadbury Schweppes plant are reported.

Apparatus for controlling fluidized beds

Science.gov (United States)

Rehmat, A.G.; Patel, J.G.

1987-05-12

An apparatus and process are disclosed for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance. 2 figs.

Effects of Different Corm Densities and Bed Types on Flower Yield Components of Saffron (Crocus sativus L.

Directory of Open Access Journals (Sweden)

A. Mollafilabi

2017-10-01

Full Text Available Introduction Saffron is among the most precious agricultural and medicinal plants of the world and has a specific placement in Iran exports. In Iran total cultivation area was 93000 ha in 2017 that from which about 96% devoted to two main provinces of saffron production including Khorasan-Razavi and South Khorasan with total production of 351 ton saffron. Saffron has unique characters including low water requirement, saffron irrigation in times that other crops do not need, farm utilization for some years, ease of transportation, lack of need to special machinery and complex technology, high capacity to use labor in time of picking flowers, occupation and in the end prevention from immigration and exchange income that make this crop becomes superior in those regions that lack of industrial perspectives and having water limitations. Organic fertilizers have effective role in saffron production including physical improvement of saffron soil, temperature relief, penetration improvement, porosity increase, and soil reducdtion in hardiness, and cause to saffron flowering. Several factors like climate, diseases, irrigation, storage, planting date, chemical and biological fertilizers and animal manure are very effective in saffron quantity and quality. Saffron yield depends on several factors like soil, crop density, planting method, corm size, geographical location, climatic factors like temperature fluctuations specially in time of flowering, rate of rainfall, cultural management and utilization period. The aim of this study was to determine possible effects of corm density and bed type on flower yield components and stigma yield of saffron. Materials and methods In order to evaluate effects of corm density and bed type on reproductive characters, yield components of flower and saffron stigma an experiment was conducted in the form of factorial as RCBD with three replicates at the research farm of Khorasan Science and Technology Part (KSTP during

Bed management team with Kanban web-based application.

Science.gov (United States)

Rocha, Hermano Alexandre Lima; Santos, Ana Kelly Lima da Cruz; Alcântara, Antônia Celia de Castro; Lima, Carmen Sulinete Suliano da Costa; Rocha, Sabrina Gabriele Maia Oliveira; Cardoso, Roberto Melo; Cremonin, Jair Rodrigues

2018-05-15

To measure the effectiveness of the bed management process that uses a web-based application with Kanban methodology to reduce hospitalization time of hospitalized patients. Before-after study was performed. The study was conducted between July 2013 and July 2017, at the Unimed Regional Hospital of Fortaleza, which has 300 beds, of which 60 are in the intensive care unit (ICU). It is accredited by International Society for Quality in Healthcare. Patients hospitalized in the referred period. Bed management with an application that uses color logic to signal at which stage of high flow the patients meet, in which each patient is interpreted as a card of the classical Kanban theory. It has an automatic user signaling system for process movement, and a system for monitoring and analyzing discharge forecasts. Length of hospital stay, number of customer complaints related to bed availability. After the intervention, the hospital's overall hospital stay time was reduced from 5.6 days to 4.9 days (P = 0.001). The units with the greatest reduction were the ICUs, with reduction from 6.0 days to 2.0 (P = 0.001). The relative percentage of complaints regarding bed availability in the hospital fell from 27% to 0%. We conclude that the use of an electronic tool based on Kanban methodology and accessed via the web by a bed management team is effective in reducing patients' hospital stay time.

Development of Chinese HTR-PM pebble bed equivalent conductivity test facility

Energy Technology Data Exchange (ETDEWEB)

Ren, Cheng; Yang, Xingtuan; Jiang, Shengyao [Tsinghua Univ., Beijing (China). Inst. of Nuclear and New Energy Technology

2016-01-15

The first two 250-MWt high-temperature reactor pebble bed modules (HTR-PM) have been installing at the Shidaowan plant in Shandong Province, China. The values of the effective thermal conductivity of the pebble bed core are essential parameters for the design. For their determination, Tsinghua University in China has proposed a full-scale heat transfer experiment to conduct comprehensive thermal transfer tests in packed pebble bed and to determine the effective thermal conductivity.

Effect of interprofessional student-led beds on emergency department performance indicators.

Science.gov (United States)

Meek, Robert; Morphet, Julia; Hood, Kerry; Leech, Michelle; Sandry, Kate

2013-10-01

The study aims to compare ED performance indicators between patients managed by students in an inter-professional learning (IPL) programme and comparable patients receiving usual ED care. An IPL programme ran for five separate 2 week periods during 2012. Four student-led beds were managed by four final year students (two medical, two nursing). Four control beds were matched for patient acuity. Data were gathered electronically from the ED information system. Comparisons of baseline characteristics and a range of ED performance indicators were made between patients managed in the student-led and control beds. Patient satisfaction with student care was surveyed. Characteristics of the 369 study and 365 control patients were similar. Median times to being seen by a nurse and a doctor were not significantly different between student-led and control beds, at 50 (19-103) versus 45 (20-93) min, and 84 (28-162) versus 91 (41-165) min, respectively. Median time to inpatient referral for admitted patients was significantly longer in student-led compared with control beds, being 142 (65-249) versus 101.5 (48-200) min, respectively. Median lengths of stay were similar between the student-led and control groups, being 263 (201-343) versus 303.5 (204-384) min for discharged patients, and 866 (571-1238) versus 745.5 (487-1168) min for inpatient ward admissions. Patients reported high levels of satisfaction with student care. There was little difference in performance indicators between patients managed by student teams as part of an IPL programme and a similar group receiving usual ED care. © 2013 Australasian College for Emergency Medicine and Australasian Society for Emergency Medicine.

The effects of a newsletter on bedding control on house dust mite allergen concentrations in childcare centers in Korea

Directory of Open Access Journals (Sweden)

Jeonghoon Kim

2015-08-01

Full Text Available Objectives Bedding in childcare centers (CCCs can hold house dust mite (HDM allergens. This study examined whether HDM allergen levels can be reduced through the distribution of an educational newsletter on bedding control to parents of CCC children in Korea. Methods All 38 CCCs were measured for Der 1 (sum of Der f 1 and Der p 1 concentrations on classroom floors and bedding before the intervention. Educational newsletters on children’s bedding control were sent to 21 CCCs by mail, and teachers were asked to distribute the newsletters to the parents of the children (intervention group. The remaining 17 CCCs were not sent newsletters (control group. The measurement of Der 1 concentrations in 38 CCCs was repeated after the intervention. Dust samples were collected with a vacuum cleaner and analyzed using enzyme-linked immunosorbent assay methods. Results The Der 1 concentrations on the bedding were significantly higher than those on the floors in 38 CCCs at baseline (p<0.05. Although changes of the Der 1 concentrations for the control group (n=17 were not significant, Der 1 concentrations for the intervention group (n=21 decreased significantly from 2077.9 ng/g dust to 963.5 ng/g dust on the floors and from 3683.9 ng/g dust to 610.4 ng/g dust on bedding (p<0.05. Conclusions The distribution of educational newsletters on bedding control to parents may be an effective means of controlling HDMs in CCCs.

Effect of fluidization number on the combustion of simulated municipal solid waste in a fluidized bed

International Nuclear Information System (INIS)

Anwar Johari; Mutahharah, M.M.; Abdul, A.; Salema, A.; Kalantarifard, A.; Rozainee, M.

2010-01-01

The effect of fluidization number on the combustion of simulated municipal solid was in a fluidized bed was investigated. Simulated municipal solid waste was used a sample and it was formulated from major waste composition found in Malaysia which comprised of food waste, paper, plastic and vegetable waste. Proximate and ultimate analyses of the simulated were conducted and results showed its composition was similar to the actual Malaysian municipal solid waste composition. Combustion study was carried out in a rectangular fluidized bed with sand of mean particle size of 0.34 mm as a fluidising medium. The range of fluidization numbers investigated was 3 to 11 U mf . The combustion was carried out at stoichiometric condition (Air Factor = 1). Results showed that the best fluidization number was in the range of 5 to 7 U mf with 5 U mf being the most optimum in which the bed temperature was sustained in a much longer period. (author)

An experimental simulation study of debris quenching in a radially stratified porous bed

International Nuclear Information System (INIS)

Sehgal, B.R.; Nayak, A.K.; Stepanyan, A.

2004-01-01

During a severe accident condition in a nuclear power plant, the core melt can fail the reactor vessel and relocate into the containment basement. In some accident management schemes, the vessel cavity is flooded with water. For these a particulate debris bed is likely to form on the cavity floor due to melt break-up in water. . In this situation, the coolability of debris bed on the containment floor is a crucial issue. This is because the debris bed still generates the decay heat and if it is uncoolable, it can eventually remelt and react with concrete basement generating a lot of noncondensable gases and pressurising the containment. Hence, it is important to cool the debris bed as an accident management programme. The main parameters affecting the coolability of the debris bed are its porosity which is a function of the size and shape of the particles which constitute the debris bed, the operating condition such as water flooding from the top or bottom of debris bed, water temperature and non-condensable gas generated during bed-concrete interactions. It is found from previous studies that the debris bed has a non-uniform particle distribution or a porosity stratification. This can happen both in radial and axial plane. For example, the bed can have a lower porosity at the centre and higher porosity at the periphery. It is of interest to investigate the quenching phenomena in such configurations so as to find an effective means of quenching the heat generating bed. While most of the previous investigations mainly concentrate on quenching of a homogenous or axially stratified particulate bed with volumetric heat generation, there are almost no studies on the above phenomena in a radially stratified porous bed. So the objective of this paper is to investigate the quenching phenomena in a radially stratified bed. To simulate the phenomena, we conducted experiments in an experimental facility named as POMECO (POrous MEdia COolability). The facility has a square

Bed-Deformation Experiments Beneath a Temperate Glacier

Science.gov (United States)

Iverson, N. R.; Hooyer, T. S.; Fischer, U. H.; Cohen, D.; Jackson, M.; Moore, P. L.; Lappegard, G.; Kohler, J.

2002-12-01

Fast flow of glaciers and genesis of glacial landforms are commonly attributed to shear deformation of subglacial sediment. Although models of this process abound, data gathered subglacially on the kinematics and mechanics of such deformation are difficult to interpret. Major difficulties stem from the necessity of either measuring deformation near glacier margins, where conditions may be abnormal, or at the bottoms of boreholes, where the scope of instrumentation is limited, drilling disturbs sediment, and local boundary conditions are poorly known. A different approach is possible at the Svartisen Subglacial Laboratory, where tunnels melted in the ice provide temporary human access to the bed of Engabreen, a temperate outlet glacier of the Svartisen Ice Cap in Norway. A trough (2 m x 1.5 m x 0.5 m deep) was blasted in the rock bed, where the glacier is 220 m thick and sliding at 0.1-0.2 m/d. During two spring field seasons, this trough was filled with 2.5 tons of simulated till. Instruments in the till recorded shear (tiltmeters), volume change, total normal stress, and pore-water pressure as ice moved across the till surface. Pore pressure was brought to near the total normal stress by feeding water to the base of the till with a high-pressure pump, operated in a rock tunnel 4 m below the bed surface. Results illustrate some fundamental aspects of bed deformation. Permanent shear deformation requires low effective normal stress and hence high pore-water pressure, owing to the frictional nature of till. Shear strain generally increases upward in the bed toward the glacier sole, consistent with previous measurements beneath thinner ice at glacier margins. At low effective normal stresses, ice sometimes decouples from underlying till. Overall, bed deformation accounts for 10-35 % of basal motion, although this range excludes shear in the uppermost 0.05 m of till where shear was not measured. Pump tests with durations ranging from seconds to hours highlight the need

Effect of a powered drive on pushing and pulling forces when transporting bariatric hospital beds.

Science.gov (United States)

Wiggermann, Neal

2017-01-01

Powered drives designed to assist with moving hospital beds are commercially available but no studies have evaluated whether they reduce the push and pull forces likely contributing to injury in caregivers. This study measured hand forces of 10 caregivers maneuvering a manual and powered bariatric bed through simulated hospital environments (hallway, elevator, and ramp). Peak push and pull forces exceeded previously established psychophysical limits for all activities with the manual bed. For the powered bed, peak forces were significantly (p pushing did not differ between beds. Powered drive may reduce the risk of injury or the number of caregivers needed for transport. Copyright © 2016 Elsevier Ltd. All rights reserved.

On the hyperporous non-linear elasticity model for fusion-relevant pebble beds

International Nuclear Information System (INIS)

Di Maio, P.A.; Giammusso, R.; Vella, G.

2010-01-01

Packed pebble beds are particular granular systems composed of a large amount of small particles, arranged in irregular lattices and surrounded by a gas filling interstitial spaces. Due to their heterogeneous structure, pebble beds have non-linear and strongly coupled thermal and mechanical behaviours whose constitutive models seem limited, being not suitable for fusion-relevant design-oriented applications. Within the framework of the modelling activities promoted for the lithiated ceramics and beryllium pebble beds foreseen in the Helium-Cooled Pebble Bed breeding blanket concept of DEMO, at the Department of Nuclear Engineering of the University of Palermo (DIN) a thermo-mechanical constitutive model has been set-up assuming that pebble beds can be considered as continuous, homogeneous and isotropic media. The present paper deals with the DIN non-linear elasticity constitutive model, based on the assumption that during the reversible straining of a pebble bed its effective logarithmic bulk modulus depends on the equivalent pressure according to a modified power law and its effective Poisson modulus remains constant. In these hypotheses the functional dependence of the effective tangential and secant bed deformation moduli on either the equivalent pressure or the volumetric strain have been derived in a closed analytical form. A procedure has been, then, defined to assess the model parameters for a given pebble bed from its oedometric test results and it has been applied to both polydisperse lithium orthosilicate and single size beryllium pebble beds.

Nonionic surfactant Brij35 effects on toluene biodegradation in a ...

African Journals Online (AJOL)

Nonionic surfactant effects on the toluene dissolved in the water phase and biodegradation kinetic behaviors of toluene in a composite bead biofilter were investigated. The toluene dissolved in the water phase was enhanced by the addition of surfactant into aqueous solution and the enhancing effect was more pronounced ...

Dryout heat flux experiments with deep heterogeneous particle bed

International Nuclear Information System (INIS)

Lindholm, I.; Holmstroem, S.; Miettinen, J.; Lestinen, V.; Hyvaerinen, J.; Pankakoski, P.; Sjoevall, H.

2006-01-01

A test facility has been constructed at Technical Research Centre of Finland (VTT) to simulate as accurately as possible the ex-vessel core particle bed in the conditions of Olkiluoto nuclear power plant. The STYX particle bed reproduces the anticipated depth of the bed and the size range of particles having irregular shape. The bed is immersed in water, creating top flooding conditions, and internally heated by an array of electrical resistance heating elements. Dryout tests have been successfully conducted at 0.1-0.7 MPa pressure for both uniformly mixed and stratified bed geometries. In all tests, including the stratified ones, the dry zone first formed near the bottom of the bed. The measured dryout heat fluxes increased with increasing pressure, from 232 kW/m 2 at near atmospheric pressure to 451 kW/m 2 at 0.7 MPa pressure. The data show some scatter even for the uniform bed. The tests with the stratified bed indicate a clear reduction of critical power due to the presence of a layer of small particles on top of the uniform bed. Comparison of data with various critical power (dryout heat flux) correlations for porous media shows that the most important parameter in the models is the effective particle diameter. Adiabatic debris bed flow resistance measurements were conducted to determine the most representative particle diameter. This diameter is close, but not equal, to the particle number-weighted average diameter of the bed material. With it, uniform bed data can be calculated to within an accuracy of 3-28% using Lipinski's 0-D model. In the stratified bed experiments, it appears that the top layer was partially fluidized, hence the measured critical power was significantly higher than calculated. Future experiments are being planned with denser top layer material to eliminate non-prototypic fluidization

Posttreatment Feeding Affects Mortality of Bed Bugs (Hemiptera: Cimicidae) Exposed to Insecticides.

Science.gov (United States)

Singh, Narinderpal; Wang, Changlu; Cooper, Richard

2016-02-01

Insecticide sprays and dusts are used for controlling bed bugs, Cimex lectularius L. In natural environments, bed bugs have daily access to hosts after they are exposed to insecticides. The established laboratory insecticide bioassay protocols do not provide feeding after insecticide treatments, which can result in inflated mortality compared with what would be encountered in the field. We evaluated the effect of posttreatment feeding on mortality of bed bugs treated with different insecticides. None of the insecticides tested had a significant effect on the amount of blood consumed and percent feeding. The effect of posttreatment feeding on bed bug mortality varied among different insecticides. Feeding significantly reduced mortality in bed bugs exposed to deltamethrin spray, an essential oil mixture (Bed Bug Fix) spray, and diatomaceous earth dust. Feeding increased the mean survival time for bed bugs treated with chlorfenapyr spray and a spray containing an essential oil mixture (Ecoraider), but did not affect the final mortality. First instars hatched from eggs treated with chlorfenapyr liquid spray had reduced feeding compared with nymphs hatched from nontreated eggs. Those nymphs hatched from eggs treated with chlorfenapyr liquid spray and successfully fed had reduced mortality and a higher mean survival time than those without feeding. We conclude that the availability of a bloodmeal after insecticide exposure has a significant effect on bed bug mortality. Protocols for insecticide efficacy testing should consider offering a bloodmeal to the treated bed bugs within 1 to 3 d after treatment. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Method and apparatus for a combination moving bed thermal treatment reactor and moving bed filter

Energy Technology Data Exchange (ETDEWEB)

Badger, Phillip C.; Dunn, Jr., Kenneth J.

2015-09-01

A moving bed gasification/thermal treatment reactor includes a geometry in which moving bed reactor particles serve as both a moving bed filter and a heat carrier to provide thermal energy for thermal treatment reactions, such that the moving bed filter and the heat carrier are one and the same to remove solid particulates or droplets generated by thermal treatment processes or injected into the moving bed filter from other sources.

Bed Bug Epidemic: A Challenge to Public Health

Science.gov (United States)

Ratnapradipa, Dhitinut; Ritzel, Dale O.; Haramis, Linn D.; Bliss, Kadi R.

2011-01-01

In recent years, reported cases of bed bug infestations in the U.S. and throughout the world have escalated dramatically, posing a global public health problem. Although bed bugs are not known to transmit disease to humans, they pose both direct and indirect public health challenges in terms of health effects, treatment, cost, and resource…

Fluid flow with heat transfer in a fix-bed

International Nuclear Information System (INIS)

Gasparetto, C.A.

1982-01-01

Tests with two different fluids, water and air, flowing in a bed with irregular particles of silica were done. The bed was confined inside a tube, which was heated by an external jacket. The bed is characterized by permeability and porosity. The tests showed a wall effect face to the relation between the tube diameter and the medium dimension of the particles. The results are presented as a relation between Nusselt number / Peclet number. (E.G.) [pt

Fluidised bed combustion system

International Nuclear Information System (INIS)

McKenzie, E.C.

1976-01-01

Fluidized bed combustion systems that facilitates the maintenance of the depth of the bed are described. A discharge pipe projects upwardly into the bed so that bed material can flow into its upper end and escape downwardly. The end of the pipe is surrounded by an enclosure and air is discharged into the enclosure so that material will enter the pipe from within the enclosure and have been cooled in the enclosure by the air discharged into it. The walls of the enclosure may themselves be cooled

Intensive Exercise Training During Bed Rest Attenuates Deconditioning

Science.gov (United States)

Greenleaf, John E.

1997-01-01

Intensive exercise training during bed rest attenuates deconditioning. Med. Sci. Sports Exerc., Vol. 29, No. 2, pp. 207-215, 1997. A 30-d 6 deg head-down bed rest project was conducted to evaluate variable high-intensity, short-duration, isotonic cycle ergometer exercise (ITE) training and high-intensity intermittent resistive isokinetic exercise (IKE) training regimens designed to maintain peak VO2 and muscle mass, strength, and endurance at ambulatory control levels throughout prolonged bed rest. Other elements of the deconditioning (adaptive) syndrome, such as proprioception, psychological performance, hypovolemia, water balance, body composition, and orthostatic tolerance, were also measured. Major findings are summarized in this paper. Compared with response during bed rest of the no exercise (NOE) control group: the ITE training regimen (a) maintained work capacity (peak VO2), (b) maintained plasma and red cell volumes, (c) induced positive body water balance, (d) decreased quality of sleep and mental concentration, and (e) had no effect on the decrease in orthostatic tolerance; the IKE training regimen (f) attenuated the decrease in peak VO2 by 50%, (g) attenuated loss of red cell volume by 40% but had no effect on loss of plasma volume, (b) induced positive body water balance, (i) had no adverse effect on quality of sleep or concentration, and 0) had no effect on the decrease in orthostatic tolerance. These findings suggest that various elements of the deconditioning syndrome can be manipulated by duration and intensity of ITE or IKE training regimens and that several different training protocols will be required to maintain or restore physiological and psychological performance of individuals confined to prolonged bed rest.

The effectiveness of a simulated scenario to teach nursing students how to perform a bed bath: A randomized clinical trial.

Science.gov (United States)

Miranda, Renata Pinto Ribeiro; de Cássia Lopes Chaves, Érika; Silva Lima, Rogério; Braga, Cristiane Giffoni; Simões, Ivandira Anselmo Ribeiro; Fava, Silvana Maria Coelho Leite; Iunes, Denise Hollanda

2017-10-01

Simulation allows students to develop several skills during a bed bath that are difficult to teach only in traditional classroom lectures, such as problem-solving, student interactions with the simulator (patient), reasoning in clinical evaluations, evaluation of responses to interventions, teamwork, communication, security and privacy. This study aimed to evaluate the effectiveness of a simulated bed bath scenario on improving cognitive knowledge, practical performance and satisfaction among nursing students. Randomized controlled clinical trial. Nursing students that were in the fifth period from two educational institutions in Brazil. Nursing students (n=58). The data were collected using the assessments of cognitive knowledge, practical performance and satisfaction were made through a written test about bed baths, an Objective Structured Clinical Examination (OSCE) and a satisfaction questionnaire. We identified that the acquisition and assimilation of cognitive knowledge was significantly higher in the simulation group (p=0.001). The performance was similar in both groups regardless of the teaching strategy (p=0.435). At follow-up, the simulation group had significantly more satisfaction with the teaching method than the control group (p=0.007). The teaching strategy based on a simulated scenario of a bed bath proved to be effective for the acquisition of cognitive knowledge regarding bed baths in clinical practice and improved student satisfaction with the teaching process. Copyright © 2017 Elsevier Ltd. All rights reserved.

WTP Pretreatment Facility Potential Design Deficiencies--Sliding Bed and Sliding Bed Erosion Assessment

Energy Technology Data Exchange (ETDEWEB)

Hansen, E. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-05-06

This assessment is based on readily available literature and discusses both Newtonian and non-Newtonian slurries with respect to sliding beds and erosion due to sliding beds. This report does not quantify the size of the sliding beds or erosion rates due to sliding beds, but only assesses if they could be present. This assessment addresses process pipelines in the Pretreatment (PT) facility and the high level waste (HLW) transfer lines leaving the PT facility to the HLW vitrification facility concentrate receipt vessel.

WTP Pretreatment Facility Potential Design Deficiencies--Sliding Bed and Sliding Bed Erosion Assessment

International Nuclear Information System (INIS)

Hansen, E. K.

2015-01-01

This assessment is based on readily available literature and discusses both Newtonian and non-Newtonian slurries with respect to sliding beds and erosion due to sliding beds. This report does not quantify the size of the sliding beds or erosion rates due to sliding beds, but only assesses if they could be present. This assessment addresses process pipelines in the Pretreatment (PT) facility and the high level waste (HLW) transfer lines leaving the PT facility to the HLW vitrification facility concentrate receipt vessel.

Discrete Element Modeling of the Mobilization of Coarse Gravel Beds by Finer Gravel Particles

Science.gov (United States)

Hill, K. M.; Tan, D.

2012-12-01

Recent research has shown that the addition of fine gravel particles to a coarse bed will mobilize the coarser bed, and that the effect is sufficiently strong that a pulse of fine gravel particles can mobilize an impacted coarser bed. Recent flume experiments have demonstrated that the degree of bed mobilization by finer particles is primarily dependent on the particle size ratio of the coarse and fine particles, rather than absolute size of either particle, provided both particles are sufficiently large. However, the mechanism behind the mobilization is not understood. It has previously been proposed that the mechanism is driven by a combination of geometric effects and hydraulic effects. For example, it has been argued that smaller particles fill in gaps along the bed, resulting in a smoother bed over which the larger particles are less likely to be disentrained and a reduced near-bed flow velocity and subsequent increased drag on protruding particles. Altered near-bed turbulence has also been cited as playing an important role. We perform simulations using the discrete element method with one-way fluid-solid coupling to conduct simulations of mobilization of a gravel bed by fine gravel particles. By independently and artificially controlling average and fluctuating velocity profiles, we systematically investigate the relative role that may be played by particle-particle interactions, average near-bed velocity profiles, and near-bed turbulence statistics. The simulations indicate that the relative importance of these mechanisms changes with the degree of mobilization of the bed. For higher bed mobility similar to bed sheets, particle-particle interactions, plays a significant role in an apparent rheology in the bed sheets, not unlike that observed in a dense granular flow of particles of different sizes. For conditions closer to a critical shear stress for bedload transport, the near-bed velocity profiles and turbulence statistics become increasingly important.

Forced Convection Heat Transfer of a sphere in Packed Bed Arrangement

International Nuclear Information System (INIS)

Lee, Dong-Young; Chung, Bum-Jin

2016-01-01

This paper analysis and discuss the forced convective heat transfer from heated single sphere, which is buried in unheated packed bed, depending on Re d with porosity. The present work determines the test matrix for the packed bed experiment. And this study discuss difference of heat transfer according to the location of heated sphere and compared heated bed with heated sphere in packed bed and compared FCC (Face Centered Cubic), HCP (Hexagonal Closed Packed) structured packed bed with random packed. This paper is to discuss and make the plan to experiment the heat transfer for depending on location of heated single sphere in unheated packed bed, to compare single sphere in packed bed with heated packed bed and to compare the structured packed bed with random packed bed. The Nu d increase as heated single sphere is close to the wall and bottom because of increasing porosity and enhancing eddy motion respectively. The existing experiment of heated sphere in packed bed do not consider the preheating effect which decrease heat transfer on downstream. The heat transfer rate of structured packed bed is different from random packed bed because of unsteady flow in random packed bed. In this study, mass transfer experiments will replace heat transfer experiments based on analogy concept. An electroplating system is adopted using limiting current technique

Forced Convection Heat Transfer of a sphere in Packed Bed Arrangement

Energy Technology Data Exchange (ETDEWEB)

Lee, Dong-Young; Chung, Bum-Jin [Kyung Hee University, Yongin (Korea, Republic of)

2016-10-15

This paper analysis and discuss the forced convective heat transfer from heated single sphere, which is buried in unheated packed bed, depending on Re{sub d} with porosity. The present work determines the test matrix for the packed bed experiment. And this study discuss difference of heat transfer according to the location of heated sphere and compared heated bed with heated sphere in packed bed and compared FCC (Face Centered Cubic), HCP (Hexagonal Closed Packed) structured packed bed with random packed. This paper is to discuss and make the plan to experiment the heat transfer for depending on location of heated single sphere in unheated packed bed, to compare single sphere in packed bed with heated packed bed and to compare the structured packed bed with random packed bed. The Nu{sub d} increase as heated single sphere is close to the wall and bottom because of increasing porosity and enhancing eddy motion respectively. The existing experiment of heated sphere in packed bed do not consider the preheating effect which decrease heat transfer on downstream. The heat transfer rate of structured packed bed is different from random packed bed because of unsteady flow in random packed bed. In this study, mass transfer experiments will replace heat transfer experiments based on analogy concept. An electroplating system is adopted using limiting current technique.

Astronomical cycle origin of bedded chert: A middle Triassic bedded chert sequence, Inuyama, Japan

Science.gov (United States)

Ikeda, Masayuki; Tada, Ryuji; Sakuma, Hironobu

2010-09-01

Astronomical forcing is one of the main drivers of climate change, and astronomical cyclicity recorded in sediments provides a clue to understand the dynamics of the global climate system. Bedded cherts consist of rhythmic alternations of chert and shale beds. Although previous studies have hypothesized that the origin of bedded chert is related to astronomical cycles (e.g. Fischer, 1976; Hori et al., 1993), conclusive proof remains elusive. To explore this possibility, we established a continuous, high-resolution lithostratigraphy of middle Triassic bedded chert in Central Japan. The average duration of each chert-shale couplet is 20 kyr, similar to that of the precession cycle. Spectral analysis of a bed number series of thickness variations in chert beds was performed assuming that each chert-shale couplet represents a 20-kyr precession cycle. The results reveal cycles involving approximately 200, 20, 5, and 2-3 beds, corresponding to periodicities of approximately 4000, 400, 100, and 40-60 kyr, respectively. By further assuming that the 20-bed cycle represents a 405-kyr eccentricity cycle of constant and stable periodicity, we converted the bed number series to a time series. Spectral analysis of the time series revealed distinct periodicities of 3600, 117, 97, and 38 kyr, in addition to 405 kyr. Besides 3600 kyr, these periodicities agree well with the 120, 95, and 37 kyr periodicities for eccentricity cycles and the obliquity cycle during the Triassic. Moreover, we detected amplitude modulation of the approximately 100-kyr cycle of thickness variations in chert beds with a 405-kyr periodicity, which may correspond to amplitude modulation of 100-kyr climatic precession cycle with the 405-kyr periodicity. The approximately 3600-kyr periodicity described above and 1800-kyr periodicity manifested as the amplitude modulation of the 405-kyr cycle are correlated to present-day long-term eccentricity cycles of 2400 and 4800 kyr evolved by chaotic behavior of solar

On the heat transfer in packed beds

International Nuclear Information System (INIS)

Sordon, G.

1988-09-01

The design of a fusion reactor blanket concept based on a bed of lithium containing ceramic pebbles or a mixture of ceramic and beryllium pebbles demands the knowledge of the effective thermal conductivity of pebble beds, including beds formed by a binary mixture of high conducting metallic pebbles and poorly conducting pebbles. In this work, binary mixtures of spheres of same diameter and different conductivities as well as beds formed by one type of spheres were investigated. The experimental apparatus consists of a stainless steel cylinder with a heating rod along the symmetry axis. Experiments with stagnant and flowing gas were performed. The pebbles were of Al 2 O 3 (diameter = 1, 2, 4 mm), of Li 4 SO 4 (diameter = 0.5 mm) of Al (diameter = 2 mm) and of steel (diameter = 2, 4 mm). Experimental values of the thermal conductivity and of the wall heat transfer coefficient are compared with the predicted ones. Modifications of already existing models were suggested. (orig.) [de

Gruppebaseret behandling af BED - et faseopdelt behandlingstilbud

DEFF Research Database (Denmark)

Laust, Jakob; Lau, Marianne Engelbrecht; Waaddegaard, Mette

2015-01-01

konsekvenser. BED blev i 2013 optaget i DSM-5 (Diagnostic and Statistical Manual of Mental Disorders) som en selvstændig diagnose og BED forventes medtaget i den forestående revision af det internationale diagnose system, ICD-11. Sundhedsstyrelsen gav på denne baggrund satspuljemidler til erfaringsopsamling...... EDE-Q: 1,7 og ved EDI: 1,5), ligesom de generelle psykiske symptomer blev mindsket i høj grad (effectsize ved WHO-5: 1,0 og ved GSI meanscore: 0,8). I alt 82 % opfyldte før behandlingens start DSM-4’s diagnostiske kriterier for BED mod 11,5 % efter behandling. 52 % fik fuld remission (ingen...... accept af og tilfredshed med behandlingen. Der var stor effekt på antal overspisninger. Før behandling havde patienterne gennemsnitligt 23,7 overspisninger pr. mdr. mod 2,3 efter behandling (effect size: 5,4). Udbyttet i forhold til den samlede spiseforstyrrelsessymptomatologi var høj (effect size ved...

THE EFFECT OF THE THICKNESS OF A PACKED BED ON THE DYNAMIC AND THERMAL BEHAVIOR OF A SOLAR DRYER

Directory of Open Access Journals (Sweden)

S KHALDI

2015-06-01

Full Text Available Drying food in the sun is a safe, easy and economical way to preserve food, especially fruits. Cabinet dryers are the most popular equipment for fruit drying. Because of intermittent nature of solar energy, storage is required for uninterrupted supply in order to match the needs. The main objective of this study is to assess effectiveness of continuous solar dryer integrated with packed bed as thermal storage with natural airflow for drying figs (Ficuscarica. The cabinet dryer were envisaged theoretically (computational fluid dynamics (CFD. The distribution of the velocity and temperature of air within the solar dryer were presented during one day of August and under the climate conditions of Tlemcen (Algeria.  The effects of presence of a packed bed on the distribution of velocity and temperature of airflow and on the temperature of figs were analyzed. The results show that the solar dryer design, incorporating a packed bed enhances the capabilities and performance of the solar dryer, through increasing time of drying.

Addition of Bacillus sp. inoculums in bedding for swine on a pilot scale: effect on microbial population and bedding temperature.

Science.gov (United States)

Corrêa, E K; Ulguim, R R; Corrêa, L B; Castilhos, D D; Bianchi, I; Gil-Turnes, C; Lucia, T

2012-10-01

Thermal and microbiological characteristics of beddings for swine were compared according to their depth and of addition of inoculums. Bedding was added to boxes at 0.25 (25D) and 0.50 m (50D), with three treatments: control (no inoculums); T1, with 250 g of Bacillus cereus var. toyoii at 8.4 × 10(7) CFU; and T2, with 250 g of a pool of B. subtilis, Bacillus licheniformis and Bacillus polymyxa at 8.4 × 10(7) CFU (250 g for 25D and 500 g for 50D). Mean temperatures were 28.5 ± 3.9 at the surface and 35.2 ± 8.9 inside the beddings. The most probable number (MPN) of thermophilic bacteria was higher for T1 and T2 than for the control (P<0.05). The MPN of thermophilic bacteria and fungi was greater for D50 than for D25 (P<0.05). The use of 25D without inoculums is recommended due to the reduction of thermophilic microbiota. Copyright © 2012 Elsevier Ltd. All rights reserved.

The bedding of laboratory animals as a source of airborne contaminants.

Science.gov (United States)

Kaliste, E; Linnainmaa, M; Meklin, T; Torvinen, E; Nevalainen, A

2004-01-01

In work environments with laboratory animals, the bedding of animals binds the excreta as well as other compounds originating from the animals and their environment. These may be generated into the ambient air when the personnel handle bedding in different procedures. This study compares the dustiness of different types of six clean and four soiled beddings from rat or mouse cages. The dust generation of clean bedding varied from beddings decreased, increased or stayed the same, depending on the type of bedding and animal species. A decrease in dustiness was, however, more common. The levels in the soiled beddings varied from bedding, the contents of bedding used in mouse, rat or rabbit cages were analysed for mesophilic bacteria and fungi, mycobacteria and endotoxins. All of these contaminants were variably found in the bedding samples, the maximal concentrations for bacteria were >6 500 000 colony-forming units (cfu)/g, for fungi 212 000 cfu/g, and for endotoxins 6500 ng/g (81 000 EU/g). The results showed that the bedding of laboratory animals may contain biologically effective compounds, and that these may be distributed into the ambient air depending on the characteristics of the bedding material. The dustiness of different bedding types is an important factor affecting the amount and quality of the occupational exposure of the personnel to airborne contaminants.

Application of CaO-Based Bed Material for Dual Fluidized Bed Steam Biomass Gasification

Science.gov (United States)

Koppatz, S.; Pfeifer, C.; Kreuzeder, A.; Soukup, G.; Hofbauer, H.

Gasification of biomass is a suitable option for decentralized energy supply based on renewable sources in the range of up to 50 MW fuel input. The paper presents the dual fluidized bed (DFB) steam gasification process, which is applied to generate high quality and nitrogen-free product gas. Essential part of the DFB process is the bed material used in the fluidized reactors, which has significant impact on the product gas quality. By the use of catalytically active bed materials the performance of the overall process is increased, since the bed material favors reactions of the steam gasification. In particular, tar reforming reactions are favored. Within the paper, the pilot plant based on the DFB process with 100kW fuel input at Vienna University of Technology, Austria is presented. Actual investigations with focus on CaO-based bed materials (limestone) as well as with natural olivine as bed material were carried out at the pilot plant. The application of CaO-based bed material shows mainly decreased tar content in the product gas in contrast to experiments with olivine as bed material. The paper presents the results of steam gasification experiments with limestone and olivine, whereby the product gas composition as well as the tar content and the tar composition are outlined.

Biodegradation of phenolic waste liquors in stirred-tank, packed-bed, and fluidized-bed bioreactors

Energy Technology Data Exchange (ETDEWEB)

Holladay, D W; Hancher, G W; Chilcote, D D; Scott, C D

1978-11-01

The biological degradation of phenolic scrub liquors similar to those that arise in coal conversion processes was studied for symbiotic bacterial populations contained in a continuously stirred tank bioreactor, a three-phase packed-bed bioreactor, and a three-phase, fluidized-bed bioreactor. The conversions of phenol compounds were comparable in the three-phase, packed-bed bioreactor and the continuously stirred tank bioreactor; however, the packed-bed bioreactor degradation rates were as much as twice those in the continuously stirred tank bioreactor, and packed-bed bioreactor retention times were as low as one- tenth those of the continuously stirred tank bioreactors (minimum time was 12 hours).

Community-wide effects of permethrin-treated bed nets on child mortality and malaria morbidity in western Kenya

NARCIS (Netherlands)

Hawley, William A.; Phillips-Howard, Penelope A.; ter Kuile, Feiko O.; Terlouw, Dianne J.; Vulule, John M.; Ombok, Maurice; Nahlen, Bernard L.; Gimnig, John E.; Kariuki, Simon K.; Kolczak, Margarette S.; Hightower, Allen W.

2003-01-01

Spatial analyses of the effect of insecticide (permethrin)-treated bed nets (ITNs) on nearby households both with and without ITNs was performed in the context of a large-scale, group-randomized, controlled mortality trial in Asembo, western Kenya. Results illustrate a protective effect of ITNs on

SU-D-204-02: BED Consistent Extrapolation of Mean Dose Tolerances

Energy Technology Data Exchange (ETDEWEB)

Perko, Z; Bortfeld, T; Hong, T; Wolfgang, J; Unkelbach, J [Massachusetts General Hospital, Boston, MA (United States)

2016-06-15

Purpose: The safe use of radiotherapy requires the knowledge of tolerable organ doses. For experimental fractionation schemes (e.g. hypofractionation) these are typically extrapolated from traditional fractionation schedules using the Biologically Effective Dose (BED) model. This work demonstrates that using the mean dose in the standard BED equation may overestimate tolerances, potentially leading to unsafe treatments. Instead, extrapolation of mean dose tolerances should take the spatial dose distribution into account. Methods: A formula has been derived to extrapolate mean physical dose constraints such that they are mean BED equivalent. This formula constitutes a modified BED equation where the influence of the spatial dose distribution is summarized in a single parameter, the dose shape factor. To quantify effects we analyzed 14 liver cancer patients previously treated with proton therapy in 5 or 15 fractions, for whom also photon IMRT plans were available. Results: Our work has two main implications. First, in typical clinical plans the dose distribution can have significant effects. When mean dose tolerances are extrapolated from standard fractionation towards hypofractionation they can be overestimated by 10–15%. Second, the shape difference between photon and proton dose distributions can cause 30–40% differences in mean physical dose for plans having the same mean BED. The combined effect when extrapolating proton doses to mean BED equivalent photon doses in traditional 35 fraction regimens resulted in up to 7–8 Gy higher doses than when applying the standard BED formula. This can potentially lead to unsafe treatments (in 1 of the 14 analyzed plans the liver mean dose was above its 32 Gy tolerance). Conclusion: The shape effect should be accounted for to avoid unsafe overestimation of mean dose tolerances, particularly when estimating constraints for hypofractionated regimens. In addition, tolerances established for a given treatment modality cannot

Bed and bed-site reuse by western lowland gorillas (Gorilla g. gorilla) in Moukalaba-Doudou National Park, Gabon.

Science.gov (United States)

Iwata, Yuji; Ando, Chieko

2007-01-01

In this paper we describe bed (nest) and bed-site reuse by western lowland gorillas (Gorilla g. gorilla) in Moukalaba-Doudou National Park, south-eastern Gabon. During an eight-month study 44 bed sites and 506 beds were found. Among these, 38.6% of bed sites and 4.1% of beds were reused. We analyzed the monthly frequency of bed-site reuse in relation to rainfall, fruit abundance, and fruit consumption by the gorillas. The different frequency of bed-site reuse in the rainy and dry seasons was not significant. More bed-site reuse was observed during the fruiting season than during the non-fruiting season. Results from fecal analysis suggested that gorillas ate more fruit in the fruiting season than in the non-fruiting season. The frugivorous diet of western gorillas may possibly cause gorillas to stay in some areas and, consequently, reuse their bed sites. Reuse of bed sites by gorillas suggests their frequent return to an area where preferred fruit is readily available. A higher percentage of arboreal beds may also affect bed-site reuse, because of the shortage of bed material.

Fluidised bed cereal cooking

International Nuclear Information System (INIS)

Jenkins, Simon Anthony

2002-01-01

Man has been cooking food for thousands of years for a number of reasons: to improve flavour and palatability, sterilise, increase digestibility, improve texture and colour. Increasingly more advanced techniques are employed today in food production plants to engineer foods with many different properties. With this in mind manufacturers are constantly seeking to improve processing techniques and apply new or different technologies (such as microwaves, RF and extrusion) to develop foods with new properties (like puffed texture starches) and to increase process efficiencies (energy efficiency, water reduction). This thesis reports on work undertaken to demonstrate the potential to achieve high temperature starch conversion of whole wheat grains in a fluidised bed, thereby reducing the amount of water required and processing time. Specifically, wheat from the farm at 14% water content is cooked in a fluidised bed. The fluidised bed heats the wheat quickly by convective heating. In addition, energy can be delivered directly to the grain by microwave heating during fluidisation. Degree of starch conversion is determined by measuring the reduction in size of endotherm of reaction as observed by Differential Scanning Calorimetry. The fluidising gas, processing temperature and starting moisture content were varied in order to investigate their effect on the cooking process. A mathematical model based on energy and species concentration equations was developed to help understand the internal grain processes. The model coupled the thermal energy equation with water diffusion. The effect of water evaporation was represented as a thermal sink in the energy equation. Popular kinetic models from literature were adapted to predict the degree of starch conversion. The model gives solutions consistent with experimental data and physical intuition. A commercial computational fluid dynamics package was used to study simple airflow and particle tracks in the fluidisation column. A

Effects of electrode geometry on the performance of dielectric barrier/packed-bed discharge plasmas in benzene degradation

International Nuclear Information System (INIS)

Jiang, Nan; Lu, Na; Shang, Kefeng; Li, Jie; Wu, Yan

2013-01-01

Highlights: • Benzene was successfully degraded by dielectric barrier/packed-bed discharge plasmas. • Different electrode geometry has distinct effect on plasmas oxidation performance. • Benzene degradation and energy performance were enhanced when using the coil electrode. • The reaction products were well determined by online FTIR analysis. -- Abstract: In this study, the effects of electrode geometry on benzene degradation in a dielectric barrier/packed-bed discharge plasma reactor with different electrodes were systematically investigated. Three electrodes were employed in the experiments, these were coil, bolt, and rod geometries. The reactor using the coil electrode showed better performance in reducing the dielectric loss in the barrier compared to that using the bolt or rod electrodes. In the case of the coil electrode, both the benzene degradation efficiency and energy yield were higher than those for the other electrodes, which can be attributed to the increased role of surface mediated reactions. Irrespective of the electrode geometry, the packed-bed discharge plasma was superior to the dielectric barrier discharge plasma in benzene degradation at any specific applied voltage. The main gaseous products of benzene degradation were CO, CO 2 , H 2 O, and formic acid. Discharge products such as O 3 , N 2 O, N 2 O 5 , and HNO 3 were also detected in the outlet gas. Moreover, the presence of benzene inhibited the formation of ozone because of the competing reaction of oxygen atoms with benzene. This study is expected to offer an optimized approach combining dielectric barrier discharge and packed-bed discharge to improve the degradation of gaseous pollutants

Computational Fluid Dynamics Simulations of Gas-Phase Radial Dispersion in Fixed Beds with Wall Effects

Directory of Open Access Journals (Sweden)

Anthony G. Dixon

2017-10-01

Full Text Available The effective medium approach to radial fixed bed dispersion models, in which radial dispersion of mass is superimposed on axial plug flow, is based on a constant effective dispersion coefficient, DT. For packed beds of a small tube-to-particle diameter ratio (N, the experimentally-observed decrease in this parameter near the tube wall is accounted for by a lumped resistance located at the tube wall, the wall mass transfer coefficient km. This work presents validated computational fluid dynamics (CFD simulations to obtain detailed radial velocity and concentration profiles for eight different computer-generated packed tubes of spheres in the range 5.04 ≤ N ≤ 9.3 and over a range of flow rates 87 ≤ Re ≤ 870 where Re is based on superficial velocity and the particle diameter dp. Initial runs with pure air gave axial velocity profiles vz(r averaged over the length of the packing. Then, simulations with the tube wall coated with methane yielded radial concentration profiles. A model with only DT could not describe the radial concentration profiles. The two-parameter model with DT and km agreed better with the bed-center concentration profiles, but not with the sharp decreases in concentration close to the tube wall. A three-parameter model based on classical two-layer mixing length theory, with a wall-function for the decrease in transverse radial convective transport in the near-wall region, showed greatly improved ability to reproduce the near-wall concentration profiles.

Modes of heat removal from a heat-generating debris bed

International Nuclear Information System (INIS)

Squarer, D.; Hochreiter, L.E.; Piecznski, A.T.

1984-01-01

In the worst hypothetical accident in a light water reactor, when all protection systems fail, the core could be converted into a deep particulate bed either in-vessel or ex-vessel. The containment of such an accident depends on the coolability of a heat-generating debris bed. Some recent experimental and analytical studies that are concerned with heat removal from such a particulate bed are reviewed. Studies have indicated that bed dryout flux and, therefore, the heat removal rate from the particulate bed increases with the particle diameter (i.e., the permeability) for pool boiling conditions and can exceed the critical heat flux of a flat plate. Bed dryout in a large particle bed (i.e., a few millimetres) was found to be closely related to the ''flooding'' limit of the bed. Dryout under forced flow conditions was found to be affected by both forced and natural convection for mass flow rate smaller than m /SUB cr/ , whereas above this mass flow rate, bed dryout is proportional to the mass flow rate. Recent analyses were found to be in agreement with experimental data; however, additional research is needed to assess factors not accounted for in previous studies (e.g., effect of pressure, multidimensionality, stratification, etc.). Based on the expected pressure and particle sizes in a postulated severe accident sequence, a debris bed should be coolable, given a sufficient water supply

Odour in composting processes at pilot scale: monitoring and biofiltration.

Science.gov (United States)

Gutiérrez, M C; Serrano, A; Martín, M A; Chica, A F

2014-08-01

Although odour emissions associated with the composting process, especially during the hydrolytic stage, are widely known, their impact on surrounding areas is not easily quantifiable, For this reason, odour emissions during the first stage ofcomposting were evaluated by dynamic olfactometry at pilot scale in order to obtain results which can be extrapolated to industrial facilities. The composting was carried out in a commercial dynamic respirometer equipped with two biofilters at pilot scale filled with prunings (Populus) and mature compost obtained from the organic fraction of municipal solid waste. Given that the highest odour emissions occur in the first stage of the composting process, this stage was carried out in a closed system to better control the odour emissions, whose maximum value was estimated to be 2.78 ouF S-1 during the experiments. Odour concentration, the dynamic respiration index and temperature showed the same evolution during composting, thus indicating that odour could be a key variable in the monitoring process. Other variables such as total organic carbon (CTOC) and pH were also found to be significant in this study due to their influence over odour emissions. The efficiency of the biofilters (empty bed residence time of 86 s) was determined by quantifying the odour emissions at the inlet and outlet of both biofilters. The moisture content in the biofilters was found to be an important variable for improving odour removal efficiency, while the minimum moisture percentage to obtain successful results was found to be 55% (odour removal efficiency of 95%).

Anaerobic fluidized bed treatment of a tannery wastewater

Energy Technology Data Exchange (ETDEWEB)

Chen, S.J.; Li, C.T.; Shieh, W.K.

1988-11-01

The anaerobic fluidized bed system, in conjunction with neutralization and chemical coagulation/flocculation, was evaluated for treatment of a tannery wastewater produced from a chrome tanning operation. Neutralization with 1 N sulphuric acid was effective for removal of chromate, with complete removal achieved at pH=8.0. Chemical coagulation/flocculation with alum at a dosage of 200 mg/L was able to remove 97% of feed SS and 65% of feed grease. Evaluation of the performance of the anaerobic fluidized bed system indicated more than 75% of feed COD could be removed up to an F/M ratio of approximately 0.4 g COD/g TVS center dot day. The observed methane production rate was 0.221 of CH/sub 4/ produced per gram COD removed. The anaerobic fluidized bed system could provide an effective treatment of a pretreated tannery wastewater.

Co-treatment of landfill leachate and domestic wastewater using a submerged aerobic biofilter.

Science.gov (United States)

Ferraz, F M; Povinelli, J; Pozzi, E; Vieira, E M; Trofino, J C

2014-08-01

This study used a pilot-scale submerged aerobic biofilter (SAB) to evaluate the co-treatment of domestic wastewater and landfill leachate that was pre-treated by air stripping. The leachate tested volumetric ratios were 0, 2, and 5%. At a hydraulic retention time of 24 h, the SAB was best operated with a volumetric ratio of 2% and removed 98% of the biochemical oxygen demand (BOD), 80% of the chemical oxygen demand (COD) and dissolved organic carbon (DOC), and 90% of the total suspended solids (TSS). A proposed method, which we called the "equivalent in humic acid" (Eq.HA) approach, indicated that the hardly biodegradable organic matter in leachate was removed by partial degradation (71% of DOC Eq.HA removal). Adding leachate at a volumetric ratio of 5%, the concentration of the hardly biodegradable organic matter was decreased primarily as a result of dilution rather than biodegradation, which was confirmed by Fourier transform infrared (FTIR) spectroscopy. The total ammoniacal nitrogen (TAN) was mostly removed (90%) by nitrification, and the SAB performances at the volumetric ratios of 0 and 2% were equal. For the three tested volumetric ratios of leachate (0, 2, and 5%), the concentrations of heavy metals in the treated samples were below the local limits. Copyright © 2014 Elsevier Ltd. All rights reserved.

Sodium and steam leak simulation studies for fluidized bed steam generators

International Nuclear Information System (INIS)

Keeton, A.R.; Vaux, W.G.; Lee, P.K.; Witkowski, R.E.

1976-01-01

An experimental program is described which was conducted to study the effects of sodium or steam leaking into an operating fluidized bed of metal or ceramic particles at 680 to 800 0 K. This effort was part of the early development studies for a fluidized-bed steam generator concept using helium as the fluidizing gas. Test results indicated that steam and small sodium leaks had no effect on the quality of fluidization, heat transfer coefficient, temperature distribution, or fluidizing gas pressure drop across the bed. Large sodium leaks, however, immediately upset the operation of the fluidized bed. Both steam and sodium leaks were detected positively and rapidly at an early stage of a leak by instruments specifically selected to accomplish this

Treatment of Produced Waters Using a Surfactant Modified Zeolite/Vapor Phase Bioreactor System

Energy Technology Data Exchange (ETDEWEB)

Lynn E. Katz; Kerry A. Kinney; R. S. Bowman; E. J. Sullivan

2004-09-11

This report summarizes work performed on this project from April 2004 through September 2004. Our previous work demonstrated that a polyurethane foam biofilter could successfully biodegrade the BTEX contaminants found in the SMZ regeneration waste gas stream. However, establishing the biomass on the polyurethane foam packing was relatively time consuming and daily recirculation of a concentrated nutrient solution was required for efficient operation of the foam biofilter. To simplify the start up and operating requirements of the biofilter system, a simple, compost-based biofilter was investigated for its ability to treat the BTEX contaminants generated during the SMZ regeneration process. The investigation of the compost biofilter was divided into three experimental phases that spanned 180 days of biofilter operation. During Phase 1, the biofilter was continuously supplied a BTEX-contaminated waste gas stream. During Phase 2, a series of periodic shutdown tests were conducted to assess how the biofilter responded when the BTEX feed was discontinued for periods ranging from 1 day to 2.8 days. The Phase 3 experiments focused on determining how the biofilter would handle periodic spikes in inlet BTEX concentration as would be expected when it is coupled with an SMZ column. Results from the continuous feed (Phase 1) experiments demonstrated that the compost biofilter could maintain BTEX removals of greater than 98% within two weeks of startup. Results of the shutdown experiments indicated that benzene removal was the most sensitive to interruptions in the BTEX feed. Nevertheless, the BTEX removal efficiency exceeded 95% within 6 hours of reestablishing the BTEX feed to the biofilter. When the biofilter was subjected to periodic spikes in BTEX concentration (Phase 3), it was found that the total BTEX removal efficiency stabilized at approximately 75% despite the fact that the biofilter was only fed BTEX contaminants 8 hours per day. Finally, the effects of nutrient

Experimental study on coolability of particulate core-metal debris bed with oxidization, (2). Fragmentation and enhanced heat transfer in zircaloy debris bed

International Nuclear Information System (INIS)

Su, Guanghui; Sugiyama, Ken-ichiro; Aoki, Hiroomi; Kimura, Iichi

2006-01-01

The oxidization and coolability characteristics of the particulate Zircaloy debris bed, which is deposited under the hard debris and through which first vapor penetrates and then water penetrates, are studied in the present paper. In the vapor penetration experiments, it is found that Zircaloy debris particles are effectively broken into small pieces after making thick oxidized layer with deep clacks by rapid oxidization under the condition that vapor with 20 cm/s penetrates for 30 to 70 min at an initial debris bed temperature of 1,030degC. It is also confirmed in the water penetration experiments that the oxidized particle debris bed has potentially of high coolability when water penetrates through the fully oxidized particle bed because of a high capillary force originating from those particles with deep cracks on their surfaces. Based on the present study, a new scenario for the appearance and disappearance of the hot spot in the TMI-2 accident is possible. The particulate core-metal core-metal debris bed is first heated up by rapid oxidization with heat generation when vapor can penetrate through the debris bed with porosities. This corresponds to the appearance of the hot spot. The resultant oxidized particulate debris bed causes a high coolability due to its high capillary force when the water can touch the debris bed at wet condition. This corresponds to the disappearance of the hot spot. (author)

An experimental study on quenching of a radially stratified heated porous bed

International Nuclear Information System (INIS)

Nayak, Arun K.; Sehgal, Bal Raj; Stepanyan, Armen V.

2006-01-01

The quenching characteristics of a volumetrically-heated particulate bed composed of radially stratified sand layers were investigated experimentally in the POMECO facility. The sand bed simulates the corium particulate debris bed which is formed when the molten corium released from the vessel fragments in water and deposits on the cavity floor during a postulated severe accident in a light water reactor (LWR). The electrically-heated bed was quenched by water from a water column established over top of it, and later also with water coming from its bottom, which was circulating from the water overlayer through downcomers. A series of experiments were conducted to reveal the effects of the size of downcomers, and their locations in the bed, on the quenching characteristics of the radially stratified debris beds. The downcomers were found to significantly increase the bed quenching rate. To simulate the non-condensable gases generated during the MCCI, air and argon were injected from the bottom of the bed at different flow rates. The effects of gas flow rate and its properties on the quenching behaviour were observed. The results indicate that the non-condensable gas flows reduce the quenching rate significantly. The gas properties also affect the quenching characteristics

Experimental studies on the coolability of packed beds. Flooding of hot dry packed beds

International Nuclear Information System (INIS)

Leininger, S.; Kulenovic, R.; Laurien, E.

2013-01-01

In case of a severe accident in a nuclear power plant meltdown of the reactor core can occur and form a packed bed in the lower plenum of the reactor pressure vessel (RPV) after solidification due to contact with water. The removal of after-heat and the long-term coolability is of essential interest. The efficient injection of cooling water into the packed bed has to be assured without endangering the structural integrity of the reactor pressure vessel. The experiments performed aimed to study the dry-out and the quenching (flooding) of hot dry packed beds. Two different inflow variants, bottom- and top-flooding including the variation of the starting temperature of the packed bed and the injection rate were studied. In case of bottom flooding the quenching time increases with increasing packed bed temperature and decreasing injection rate. In case of top flooding the flow pattern is more complex, in a first phase the water flows preferentially toward the RPV wall, the flow paths conduct the water downwards. The flow resistance of the packed bed increases with increasing bed temperatures. The quenching temperatures increase significantly above average.

The effects of applying silicon carbide coating on core reactivity of pebble-bed HTR in water ingress accident

Energy Technology Data Exchange (ETDEWEB)

Zuhair, S.; Setiadipura, Topan [National Nuclear Energy Agency of Indonesia, Serpong Tagerang Selatan (Indonesia). Center for Nuclear Reactor Technology and Safety; Su' ud, Zaki [Bandung Institute of Technology (Indonesia). Dept. of Physics

2017-03-15

Graphite is used as the moderator, fuel barrier material, and core structure in High Temperature Reactors (HTRs). However, despite its good thermal and mechanical properties below the radiation and high temperatures, it cannot avoid corrosion as a consequence of an accident of water/air ingress. Degradation of graphite as a main HTR material and the formation of dangerous CO gas is a serious problem in HTR safety. One of the several steps that can be adopted to avoid or prevent the corrosion of graphite by the water/air ingress is the application of a thin layer of silicon carbide (SiC) on the surface of the fuel element. This study investigates the effect of applying SiC coating on the fuel surfaces of pebble-bed HTR in water ingress accident from the reactivity points of view. A series of reactivity calculations were done with the Monte Carlo transport code MCNPX and continuous energy nuclear data library ENDF/B-VII at temperature of 1200 K. Three options of UO{sub 2}, PuO{sub 2}, and ThO{sub 2}/UO{sub 2} fuel kernel were considered to obtain the inter comparison of the core reactivity of pebble-bed HTR in conditions of water/air ingress accident. The calculation results indicated that the UO{sub 2}-fueled pebble-bed HTR reactivity was slightly reduced and relatively more decreased when the thickness of the SiC coating increased. The reactivity characteristic of ThO{sub 2}/UO{sub 2}-fueled pebble-bed HTR showed a similar trend to that of UO{sub 2}, but did not show reactivity peak caused by water ingress. In contrast with UO{sub 2}- and ThO{sub 2}-fueled pebble-bed HTR, although the reactivity of PuO{sub 2}-fueled pebble-bed HTR was the lowest, its characteristics showed a very high reactivity peak (0.33 Δk/k) and this introduction of positive reactivity is difficult to control. SiC coating on the surface of the plutonium fuel pebble has no significant impact. From the comparison between reactivity characteristics of uranium, thorium and plutonium cores with 0

Modeling of Seepage Losses in Sewage Sludge Drying Bed ...

African Journals Online (AJOL)

This research was carried out to develop a model governing seepage losses in sewage sludge drying bed. The model will assist in the design of sludge drying beds for effective management of wastes derived from households' septic systems. In the experiment conducted this study, 125kg of sewage sludge, 90.7% moisture ...

Hydrogen sulfide release from dairy manure storages containing gypsum bedding

Science.gov (United States)

Recycled gypsum products can provide a cost-effective bedding alternative for dairy producers. Manufacturers report reduced odors, moisture and bacteria in the stall environment when compared to traditional bedding. Gypsum provides a sulfate source that can be converted to hydrogen sulfide under ana...

Particle flow of ceramic breeder pebble beds in bi-axial compression experiments

International Nuclear Information System (INIS)

Hermsmeyer, S.; Reimann, J.

2002-01-01

Pebble beds of Tritium breeding ceramic material are investigated within the framework of developing solid breeder blankets for future nuclear fusion power plants. For the thermo-mechanical characterisation of such pebble beds, bed compression experiments are the standard tools. New bi-axial compression experiments on 20 and 30 mm high pebble beds show pebble flow effects much more pronounced than in previous 10 mm beds. Owing to the greater bed height, conditions are reached where the bed fails in cross direction and unhindered flow of the pebbles occurs. The paper presents measurements for the orthosilicate and metatitanate breeder materials that are envisaged to be used in a solid breeder blanket. The data are compared with calculations made with a Drucker-Prager soil model within the finite-element code ABAQUS, calibrated with data from other experiments. It is investigated empirically whether internal bed friction angles can be determined from pebble beds of the considered heights, which would simplify, and broaden the data base for, the calibration of the Drucker-Prager pebble bed models

Supraesophageal Reflux: Correlation of Position and Occurrence of Acid Reflux-Effect of Head-of-Bed Elevation on Supine Reflux.

Science.gov (United States)

Scott, David R; Simon, Ronald A

2015-01-01

Supraesophageal reflux of gastric contents can contribute to perennial nasopharyngitis, cough, and asthma. However, effective treatment strategies for supraesophageal reflux disease (SERD) remain inadequately defined. The purpose of this study is to assess the prevalence and timing of SERD and to investigate the efficacy of head-of-bed elevation in its treatment. A retrospective chart review of patients seen at Scripps Clinic Division of Allergy, Asthma and Immunology was performed who had undergone overnight nasopharyngeal pH monitoring with a commercially available nasopharyngeal pH-monitoring device, Dx-pH Measurement System from Restech, San Diego, Calif. Subjects with reflux were classified based on the position of reflux as either supine only, upright only, or both supine and upright. In a subset of subjects with supine-only reflux, pH monitoring was compared before and after elevating the head of bed 6 inches. Adequate nasopharyngeal pH-monitoring data were obtained for 235 patients. Reflux was detected in 113 (48%) patients. The pattern of reflux observed was 62 (55%) supine only, 4 (4%) upright only, and 47 (42%) upright and supine. Sequential overnight nasopharyngeal pH monitoring before and after head-of-bed elevation was obtained in 13 individuals with supine-only reflux. Ten subjects demonstrated significant improvement, 8 of whom demonstrated complete resolution of supine reflux with 6 inches of head-of-bed elevation. This study provides new evidence that SERD frequently occurs in the supine position and that 6 inches of head-of-bed elevation is effective in reducing supine SERD. Copyright © 2015 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

Analysis of wall-packed-bed thermal interactions

International Nuclear Information System (INIS)

Gorbis, Z.R.; Tillack, M.S.; Tehranian, F.; Abdou, M.A.

1995-01-01

One of the major issues remaining for ceramic breeder blankets involves uncertainties in heat transfer and thermomechanical interactions within the breeder and multiplier regions. Particle bed forms are considered in many reactor blanket designs for both the breeder and Be multiplier. The effective thermal conductivity of beds and the wall-bed thermal conductance are still not adequately characterized, particularly under the influence of mechanical stresses. The problem is particularly serious for the wall conductance between Be and its cladding, where the uncertainty can be greater than 50%. In this work, we describe a new model for the wall-bed conductance that treats the near-wall region as a finite-width zone. The model includes an estimate of the region porosity based on the number of contact points, and the contact area for smooth surfaces. It solves the heat conduction in a near-wall unit cell. The model is verified with existing data and used to predict the range of wall conductances expected in future simulation experiments and in reactor applications. (orig.)

Effect of humidity on thoron adsorption in activated charcoal bed

International Nuclear Information System (INIS)

Sudeep Kumara, K.; Karunakara, N.; Yashodhara, I.; Sapra, B.K.; Sahoo, B.K.; Gaware, J.J.; Kanse, S.D.; Mayya, Y.S.

2014-01-01

Activated charcoal is a well-known adsorber of 222 Rn and 220 Rn gases. This property can be effectively used for remediation of these gases in the workplaces of uranium and thorium processing facilities. However, the adsorption on charcoal is sensitive to variation in temperature and humidity. The successful designing and characterization of adsorption systems require an adequate understanding of these sensitivities. The study has been carried out towards this end, to delineate the effect of relative humidity on the efficacy of 220 Rn mitigations in a charcoal bed. Air carrying 220 Rn from a Pylon source was passed through a column filled with coconut shell-based granular activated charcoal. The relative humidity of the air was controlled, and the transmission characteristics were examined at relative humidity varying from 45% to 60%. The mitigation factor was found to decrease significantly with an increase of humidity in the air. (author)

Effect of permethrin-treated bed nets on the spatial distribution of malaria vectors in western Kenya

NARCIS (Netherlands)

Gimnig, John E.; Kolczak, Margarette S.; Hightower, Allen W.; Vulule, John M.; Schoute, Erik; Kamau, Luna; Phillips-Howard, Penelope A.; ter Kuile, Feiko O.; Nahlen, Bernard L.; Hawley, William A.

2003-01-01

The effect of insecticide (permethrin)-treated bed nets (ITNs) on the spatial distribution of malaria vectors in neighboring villages lacking ITNs was studied during a randomized controlled trial of ITNs in western Kenya. There was a trend of decreased abundance of Anopheles gambiae with decreasing

Prevention of Bed Agglomeration Problems in a Fluidized Bed Boiler by Finding the Trigging Value of Sewage Sludge Dosage Added to Combustion of Biofuels

Energy Technology Data Exchange (ETDEWEB)

Andersson, Kajsa; Gervind, Pernilla

2009-07-01

Agglomeration of bed sand is a common problem during combustion of biofuels with high ash content in fluidized bed boilers. Former studies have shown that co-combustion of biofuels with sewage sludge increases the agglomeration temperature. Sewage sludge has a low heating value and high ash content. It would therefore be better to use sludge as an additive to the combustion than as a co-combusted biofuel. In this study the trigging value of sludge addition to the combustion of some biofuel was investigated. The effect of adding sludge with different precipitation chemicals, iron sulphate and aluminium sulphate, was investigated. The biofuels used for the experiments were bark, refused derived fuel (RDF) and a mixture of wood and straw, 75/25 % on energy basis. All experiments were carried out in a laboratory scale fluidized bed reactor. Analyses of chemical composition of bed sand and SEM/EDX analyses were performed after the combustion. Eventually agglomeration tests were performed in order to find the agglomeration temperature of the samples. Some of the samples sintered during the combustion and were not tested for the agglomeration temperature. SEM/EDX showed that all samples of bed sand contained sand particles with more or less coatings. In some cases the coatings seemed to consist of one dense inner layer and one more porous outer layer. From SEM/EDX and chemical composition analyses it was found that the total amount of phosphorous in the bed sand samples was increased with an increased addition of sludge in all experiments. The concentration of phosphorous was especially higher in the outer layers/coatings. It was also found that elements from the sludge seem to get caught by a sticky layer at the bed sand surface and form a non-sticky or less sticky layer that prevents agglomeration. The total amount of aluminium was increased with an increased addition of sludge for the wood/straw samples, while it increased with an increased amount of combusted fuel for