WorldWideScience

Sample records for bearings part ii

  1. The Influence of Injection Pockets on the Performance of Tilting-Pad Thrust Bearings: Part II – Comparison Between Theory and Experiment

    DEFF Research Database (Denmark)

    Heinrichson, Niels; Santos, Ilmar

    2006-01-01

    This is Part II of a two-part series of papers describing the effects of high pressure injection pockets on the operating conditions of tilting-pad thrust bearings. Measurements of the distribution of pressure and oil film thickness are presented for tilting-pad thrust bearing pads of approximately...... 100 cm2 surface area. Two pads are measured in a laboratory test-rig at loads of approximately 0.5, 1.5 and 4.0 MPa and velocities of up to 33 m/s. One pad has a plain surface. The other pad has a conical injection pocket at the pivot point and a leading edge taper. The measurements are compared...... to theoretical values obtained using a three dimensional thermo-elasto-hydrodynamic (TEHD) numerical model. At low and intermediate loads the theoretical pressure distribution corresponds well to the measured values for both pads although the influence of the pocket is slightly underestimated. At high loads...

  2. The Influence of Injection Pockets on the Performance of Tilting-Pad Thrust Bearings - Part II: Comparison Between Theory and Experiment

    DEFF Research Database (Denmark)

    Heinrichson, Niels; Fuerst, Axel; Santos, Ilmar

    2007-01-01

    This is Part II of a two-part series of papers describing the effects of high-pressure injection pockets on the operating conditions of tilting-pad thrust bearings. The paper has two main objectives. One is an experimental investigation of the influence of an oil injection pocket on the pressure...... and without oil injection) on the pressure distribution and oil film thickness. Measurements of the distribution of pressure and oil film thickness are presented for tilting-pad thrust bearing pads of approx. 100 cm^2 surface area. Two pads are measured in a laboratory test rig at loads of approx. 1.5 MPa...... and approx. 4.0 MPa and velocities of up to 33 m/s. One pad has a plain surface. The other pad has a conical injection pocket at the pivot point and a leading-edge taper. The measurements are compared to theoretical values obtained using a three-dimensional thermoelastohydrodynamic (TEHD) numerical model...

  3. Workshop 96. Part II

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    Part II of the seminar proceedings contains contributions in various areas of science and technology, among them materials science in mechanical engineering, materials science in electrical, chemical and civil engineering, and electronics, measuring and communication engineering. In those areas, 6 contributions have been selected for INIS. (P.A.).

  4. Workshop 96. Part II

    International Nuclear Information System (INIS)

    1995-12-01

    Part II of the seminar proceedings contains contributions in various areas of science and technology, among them materials science in mechanical engineering, materials science in electrical, chemical and civil engineering, and electronics, measuring and communication engineering. In those areas, 6 contributions have been selected for INIS. (P.A.)

  5. Stiffnites. Part II

    Directory of Open Access Journals (Sweden)

    Maria Teresa Pareschi

    2011-06-01

    Full Text Available

    The dynamics of a stiffnite are here inferred. A stiffnite is a sheet-shaped, gravity-driven submarine sediment flow, with a fabric made up of marine ooze. To infer stiffnite dynamics, order of magnitude estimations are used. Field deposits and experiments on materials taken from the literature are also used. Stiffnites can be tens or hundreds of kilometers wide, and a few centimeters/ meters thick. They move on the sea slopes over hundreds of kilometers, reaching submarine velocities as high as 100 m/s. Hard grain friction favors grain fragmentation and formation of triboelectrically electrified particles and triboplasma (i.e., ions + electrons. Marine lipids favor isolation of electrical charges. At first, two basic assumptions are introduced, and checked a posteriori: (a in a flowing stiffnite, magnetic dipole moments develop, with the magnetization proportional to the shear rate. I have named those dipoles as Ambigua. (b Ambigua are ‘vertically frozen’ along stiffnite streamlines. From (a and (b, it follows that: (i Ambigua create a magnetic field (at peak, >1 T. (ii Lorentz forces sort stiffnite particles into two superimposed sheets. The lower sheet, L+, has a sandy granulometry and a net positive electrical charge density. The upper sheet, L–, has a silty muddy granulometry and a net negative electrical charge density; the grains of sheet L– become finer upwards. (iii Faraday forces push ferromagnetic grains towards the base of a stiffnite, so that a peak of magnetic susceptibility characterizes a stiffnite deposit. (iv Stiffnites harden considerably during their motion, due to magnetic confinement. Stiffnite deposits and inferred stiffnite characteristics are compatible with a stable flow behavior against bending, pinch, or other macro instabilities. In the present report, a consistent hypothesis about the nature of Ambigua is provided.

  6. Part II. Population

    International Nuclear Information System (INIS)

    2004-01-01

    This monograph deals with assessment of radiological health effects of the Chernobyl accident for emergency workers (part 1) and the population of the contaminated areas in Russia (part 2). The Chernobyl emergency workers and people living in the contaminated areas of Russia received much lower doses than the population of Hiroshima and Nagasaki and it was unclear whether risks of radiation-induced cancers derived with the Japanese data could be extrapolated to the low dose range However, it was predicted as early as in 1990 that the thyroid cancer incidence might be increasing due to incorporated 131 irradiation. What conclusions can be drawn from regarding cancer incidence among emergency workers and residents of the contaminated areas in Russia and the role of the radiation factor on the basis of the registry data? Leukemia incidence. Leukemia incidence is known to be one of principal indications of radiation effects. The radiation risk for leukemias is 3-4 times higher that for solid cancers and its latent period is estimated to be 2-3 years after exposure. Results of the radiation epidemiological studies discussed in this book show that in the worst contaminated Bryansk region the leukemia incidence rate is not higher than in the country in general. Even though some evidence exists for the dose response relationship, the radiation risks appear to be not statistically significant. Since risks of leukemia are known to be higher for those who were children at exposure, long-term epidemiological studies need to be continued. The study of leukemias among emergency workers strongly suggest the existence of dose response relationship. In those who received external doses more than 0.15 Gy the leukemia incidence rate is two time higher and these emergency workers should be referred to as a group of increased radiation risk. Solid cancers. The obtained results provide no evidence to a radiation-induced increase in solid cancers among residents of the contaminated areas

  7. The Influence of Injection Pockets on the Performance of Tilting-Pad Thrust Bearings - Part I: Theory

    DEFF Research Database (Denmark)

    Heinrichson, Niels; Santos, Ilmar; Fuerst, Axel

    2007-01-01

    This is Part I of a two-part series of papers describing the effects of high-pressure injection pockets on the operating conditions of tilting-pad thrust bearings. In Part I a numerical model based on the Reynolds equation is developed extending the threedimensional thermoelastohydrodynamic (TEHD......) analysis of tilting-pad thrust bearings to include the effects of high-pressure injection and recesses in the bearing pads. The model is applied to the analysis of an existing bearing of large dimensions and the influence of the pocket is analyzed. In the analysis, the high-pressure oil injection used...... for hydrostatic jacking is turned off (i.e., only the effect of the pocket is studied). It is shown that a shallow pocket positively influences the performance of the bearing because it has characteristics similar to those of a Rayleigh-step bearing. In Part II of the paper (Heinrichson, N., Fuerst, A...

  8. 76 FR 10335 - Ball Bearings and Parts Thereof From Germany: Initiation of Antidumping Duty Changed...

    Science.gov (United States)

    2011-02-24

    ... (June 30, 2010). After analysis of the quantity and value of the sales of ball bearings and parts... the order remains dispositive. The size or precision grade of a bearing does not influence whether the... influence whether the bearing is covered by the order. Bearings designed for highly specialized applications...

  9. Exploring Water Pollution. Part II

    Science.gov (United States)

    Rillo, Thomas J.

    1975-01-01

    This is part two of a three part article related to the science activity of exploring environmental problems. Part one dealt with background information for the classroom teacher. Presented here is a suggested lesson plan on water pollution. Objectives, important concepts and instructional procedures are suggested. (EB)

  10. Roots/Routes: Part II

    Science.gov (United States)

    Swanson, Dalene M.

    2009-01-01

    This narrative acts as an articulation of a journey of many routes. Following Part I of the same research journey of rootedness/routedness, it debates the nature of transformation and transcendence beyond personal and political paradoxes informed by neoliberalism and related repressive globalizing discourses. Through a more personal, descriptive,…

  11. Atmospheric fluoride pollution. Part II

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, T; Yamazaki, Y

    1969-01-01

    In East Osaka, agricultural crops either died or showed poor growth in the neighborhood of a factory producing white cosmetic bottles. Since fluorite was used as a material and there was no damage before the establishment of the factory, it was suspected that fluorine compounds were causing the damage. Quantitative analysis was performed on the agricultural crops and the exhaust gas as well as the dust particles in order to determine the fluorine content. Gas samplers were used to collect the dusts from the surrounding atmosphere. The fluorine content of dust near the factory was about 93 mg per cubic meter per day, and in some parts, as high as 1.54 mq per cubic meter per day. Relatively larger quantities of fluorine were measured at the southwestern and southeastern area of the factory, corresponding to the general wind pattern. Rice and soy beans from the neighborhood of the factory showed concentrations of fluorine and, especially in the leaves of the damaged crops, the concentrations were several hundred times higher than those of the undamaged leaves.

  12. Acoustic Emission Monitoring of Incipient in Journal Bearings - Part I : Detectability and measurement for bearing damages

    International Nuclear Information System (INIS)

    Yoon, Dong Jin; Kwon, Oh Yang; Chung, Min Hwa; Kim, Kyung Woong

    1994-01-01

    In contrast to the machinery using rolling element bearings, systems with journal bearings generally operate in large scale and under severe loading condition such as steam generator turbines and internal combustion engines. Failure of the bearings in these machinery can result in the system breakdown. To avoid the time consuming repair and considerable economic loss, the detection of incipient failure in journal bearings becomes very important. In this experimental approach, acoustic emission monitoring is applied to the detection of incipient failure caused by several types of abnormal operating condition most probable in the journal bearing systems. It has been known that the intervention of foreign materials, insufficient lubrication and misassembly etc. are principal factors to cause bearing failure and distress. The experiment was conducted under such designed conditions as hard particles in the lubrication layer, insufficient lubrication, and metallic contact in the simulated journal bearing system. The results showed that acoustic emission could be an effective tool to detect the incipient failure in journal bearings

  13. Unlearning Established Organizational Routines--Part II

    Science.gov (United States)

    Fiol, C. Marlena; O'Connor, Edward J.

    2017-01-01

    Purpose: The purpose of Part II of this two-part paper is to uncover important differences in the nature of the three unlearning subprocesses, which call for different leadership interventions to motivate people to move through them. Design/methodology/approach: The paper draws on research in behavioral medicine and psychology to demonstrate that…

  14. Nuclear medicine and thyroid disease - part II

    International Nuclear Information System (INIS)

    Chatterton, B.E.

    2005-01-01

    Part 1 of this article discussed the anatomy, physiology and basic pathology of the thyroid gland. Techniques of thyroid scanning and a few clinical examples are shown part II Copyright (2005) The Australian and New Zealand Society Of Nuclear Medicine Inc

  15. Contact Stress Design Parameters for Titanium Bearings, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Air-Lock's Phase I effort tested the effects of ball induced contact stresses on Titanium bearing races. The contact stress design limit that would achieve a...

  16. Typewriting Syllabus: Part II: Modules. 1976 Revision.

    Science.gov (United States)

    New York State Education Dept., Albany. Bureau of Occupational and Career Curriculum Development.

    The document is the second of a two-part set on typewriting and focuses on the nine modules of instruction. The nine modules are: (1) keyboard mastery and skill development, (2) basic typewriting competencies, (2a) personal use typewriting, (3) introduction to office typewriting I, (4) introduction to office typewriting II, (5) intermediate office…

  17. Active tilting-pad journal bearings supporting flexible rotors: Part II–The model-based feedback-controlled lubrication

    DEFF Research Database (Denmark)

    Salazar, Jorge Andrés González; Santos, Ilmar

    2017-01-01

    This is part II of a twofold paper series dealing with the design and implementation of model-based controllers meant for assisting the hybrid and developing the feedback-controlled lubrication regimes in active tilting pad journal bearings (active TPJBs). In both papers theoretical and experimen...... derived in part I. Results show further suppression of resonant vibrations when using the feedback-controlled or active lubrication, overweighting the reduction already achieved with hybrid lubrication, thus improving the whole machine dynamic performance.......This is part II of a twofold paper series dealing with the design and implementation of model-based controllers meant for assisting the hybrid and developing the feedback-controlled lubrication regimes in active tilting pad journal bearings (active TPJBs). In both papers theoretical...... and experimental analyses are presented with focus on the reduction of rotor lateral vibration. This part is devoted to synthesising model-based LQG optimal controllers (LQR regulator + Kalman Filter) for the feedback-controlled lubrication and is based upon the mathematical model of the rotor-bearing system...

  18. Globalization in the pharmaceutical industry, Part II.

    Science.gov (United States)

    Casadio Tarabusi, C; Vickery, G

    1998-01-01

    This is the second of a two-part report on the pharmaceutical industry. Part II begins with a discussion of foreign direct investment and inter-firm networks, which covers international mergers, acquisitions, and minority participation; market shares of foreign-controlled firms; international collaboration agreements (with a special note on agreements in biotechnology); and licensing agreements. The final section of the report covers governmental policies on health and safety regulation, price regulation, industry and technology, trade, foreign investment, protection of intellectual property, and competition.

  19. Physical metallurgy of BATMAN II Ti-bearing martensitic steels

    International Nuclear Information System (INIS)

    Pilloni, L.; Attura, F.; Calza-Bini, A.; Santis, G. de; Filacchioni, G.

    1998-01-01

    Seven laboratory experimental casts of 7-9% Cr Ti-bearing martensitic steels were obtained via VIM process. Plates of 25 mm thickness were produced by hot rolling. On each cast CCT diagrams and critical temperatures were determined. Several austenitizing treatments were performed to study the grain size evolution. The effect of microstructure on impact properties were finally investigated. This paper discusses the role of chemical composition on microstructural and physical properties and shows the beneficial effect either of low-temperature austenitizing or double-austenitizing steps on impact properties. (orig.)

  20. Continuum Thermodynamics - Part II: Applications and Examples

    Science.gov (United States)

    Albers, Bettina; Wilmanski, Krzysztof

    The intention by writing Part II of the book on continuum thermodynamics was the deepening of some issues covered in Part I as well as a development of certain skills in dealing with practical problems of oscopic processes. However, the main motivation for this part is the presentation of main facets of thermodynamics which appear when interdisciplinary problems are considered. There are many monographs on the subjects of solid mechanics and thermomechanics, on fluid mechanics and on coupled fields but most of them cover only special problems in great details which are characteristic for the chosen field. It is rather seldom that relations between these fields are discussed. This concerns, for instance, large deformations of the skeleton of porous materials with diffusion (e.g. lungs), couplings of deformable particles with the fluid motion in suspensions, couplings of adsorption processes and chemical reactions in immiscible mixtures with diffusion, various multi-component aspects of the motion, e.g. of avalanches, such as segregation processes, etc...

  1. 76 FR 41761 - Ball Bearings and Parts Thereof From Japan and the United Kingdom: Revocation of Antidumping Duty...

    Science.gov (United States)

    2011-07-15

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-588-804, A-412-801] Ball Bearings and... Commerce (the Department) is revoking the antidumping duty orders on ball bearings and parts thereof from...: Background On May 15, 1989, the Department published the antidumping duty orders on ball bearings and parts...

  2. 76 FR 327 - Ball Bearings and Parts Thereof From France: Partial Rescission of Antidumping Duty...

    Science.gov (United States)

    2011-01-04

    ...In response to requests from interested parties, the Department of Commerce (the Department) initiated an administrative review of the antidumping duty order on ball bearings and parts thereof from France. The period of review is May 1, 2009, through April 30, 2010. The Department is rescinding this review in part.

  3. Kinetics and Products of Chromium(VI) Reduction by Iron(II/III)-Bearing Clay Minerals.

    Science.gov (United States)

    Joe-Wong, Claresta; Brown, Gordon E; Maher, Kate

    2017-09-05

    Hexavalent chromium is a water-soluble pollutant, the mobility of which can be controlled by reduction of Cr(VI) to less soluble, environmentally benign Cr(III). Iron(II/III)-bearing clay minerals are widespread potential reductants of Cr(VI), but the kinetics and pathways of Cr(VI) reduction by such clay minerals are poorly understood. We reacted aqueous Cr(VI) with two abiotically reduced clay minerals: an Fe-poor montmorillonite and an Fe-rich nontronite. The effects of ionic strength, pH, total Fe content, and the fraction of reduced structural Fe(II) [Fe(II)/Fe(total)] were examined. The last variable had the largest effect on Cr(VI) reduction kinetics: for both clay minerals, the rate constant of Cr(VI) reduction varies by more than 3 orders of magnitude with Fe(II)/Fe(total) and is described by a linear free energy relationship. Under all conditions examined, Cr and Fe K-edge X-ray absorption near-edge structure spectra show that the main Cr-bearing product is a Cr(III)-hydroxide and that Fe remains in the clay structure after reacting with Cr(VI). This study helps to quantify our understanding of the kinetics of Cr(VI) reduction by Fe(II/III)-bearing clay minerals and may improve predictions of Cr(VI) behavior in subsurface environments.

  4. The Mid America Heart Institute: part II.

    Science.gov (United States)

    McCallister, Ben D; Steinhaus, David M

    2003-01-01

    The Mid America Heart Institute (MAHI) is one of the first and largest hospitals developed and designed specifically for cardiovascular care. The MAHI hybrid model, which is a partnership between the not-for-profit Saint Luke's Health System, an independent academic medical center, and a private practice physician group, has been extremely successful in providing high-quality patient care as well as developing strong educational and research programs. The Heart Institute has been the leader in providing cardiovascular care in the Kansas City region since its inception in 1975. Although challenges in the future are substantial, it is felt that the MAHI is in an excellent position to deal with the serious issues in health care because of the Heart Institute, its facility, organization, administration, dedicated medical and support staff, and its unique business model of physician management. In part I, the authors described the background and infrastructure of the Heart Institute. In part II, cardiovascular research and benefits of physician management are addressed.

  5. Benchmark matrix and guide: Part II.

    Science.gov (United States)

    1991-01-01

    In the last issue of the Journal of Quality Assurance (September/October 1991, Volume 13, Number 5, pp. 14-19), the benchmark matrix developed by Headquarters Air Force Logistics Command was published. Five horizontal levels on the matrix delineate progress in TQM: business as usual, initiation, implementation, expansion, and integration. The six vertical categories that are critical to the success of TQM are leadership, structure, training, recognition, process improvement, and customer focus. In this issue, "Benchmark Matrix and Guide: Part II" will show specifically how to apply the categories of leadership, structure, and training to the benchmark matrix progress levels. At the intersection of each category and level, specific behavior objectives are listed with supporting behaviors and guidelines. Some categories will have objectives that are relatively easy to accomplish, allowing quick progress from one level to the next. Other categories will take considerable time and effort to complete. In the next issue, Part III of this series will focus on recognition, process improvement, and customer focus.

  6. 75 FR 62763 - Ball Bearings and Parts Thereof From Germany: Amended Final Results of Antidumping Duty...

    Science.gov (United States)

    2010-10-13

    ...On July 7, 2010, the United States Court of International Trade (CIT) sustained the Department of Commerce's (the Department) results of redetermination on remand concerning the final results of the administrative review of the antidumping duty order on ball bearings and parts thereof from Germany. See SKF USA Inc. v. United States, Slip Op. 10-76 (CIT 2010). The Department is amending the final results of the administrative review of the antidumping duty order on ball bearings and parts thereof from Germany covering the period of review May 1, 2006, through April 30, 2007, to reflect the CIT's order.

  7. HERBICIDAS INIBIDORES DO FOTOSSISTEMA IIPARTE II / PHOTOSYSTEM II INHIBITOR HERBICIDES - PART

    Directory of Open Access Journals (Sweden)

    ILCA P. DE F. E SILVA

    2013-11-01

    Full Text Available Os herbicidas inibidores do fotossistema II (PSII ligam-se ao sítio da QB localizado na proteína D1 o qual se localiza na membrana dos tilacóides dos cloroplastos, causando, o bloqueia do transporte de elétrons da QA para QB, tendo como consequência, a peroxidação dos lipídios. Os principais fatores que afetam a evolução da resistência de plantas daninhas aos herbicidas têm sido agrupados em: genéticos, bioecológicos e agronômicos. A resistência de plantas daninhas a herbicidas é definida como a habilidade de uma planta sobreviver e reproduzir, após exposição a uma dose de herbicida normalmente letal para um biótipo normal da planta. A seletividade de um herbicida está relacionada à capacidade de eliminar plantas daninhas sem interferir na qualidade da planta de interesse econômico.

  8. 77 FR 53844 - Ball Bearings and Parts Thereof From France and Italy: Rescission of Antidumping Duty...

    Science.gov (United States)

    2012-09-04

    ...In response to requests from interested parties, the Department of Commerce (the Department) initiated administrative reviews of the antidumping duty orders on ball bearings and parts thereof from France and Italy. The period of review is May 1, 2011, through September 14, 2011. As a result of the withdrawals of the requests for review, the Department is rescinding these reviews.

  9. 78 FR 9674 - Ball Bearings and Parts Thereof From Germany: Preliminary Results of Antidumping Duty...

    Science.gov (United States)

    2013-02-11

    ...The Department of Commerce (the Department) is conducting an administrative review of the antidumping duty order on ball bearings and parts thereof from Germany. The period of review (POR) is May 1, 2011, through September 14, 2011.\\1\\ We preliminarily find that subject merchandise has not been sold at less than normal value. ---------------------------------------------------------------------------

  10. 75 FR 3444 - Ball Bearings and Parts Thereof From Germany: Initiation of Antidumping Duty Changed...

    Science.gov (United States)

    2010-01-21

    ...Pursuant to section 751(b) of the Tariff Act of 1930, as amended, and 19 CFR 351.216 and 351.221(c)(3), the Department of Commerce is initiating a changed-circumstances review of the antidumping duty order on ball bearings and parts thereof from Germany with respect to myonic GmbH.

  11. Structures and Properties of Polyurethanes. Part II,

    Science.gov (United States)

    1979-03-23

    effect was observed for polymethyl methacrylate (222, 2721. The polyol, which contain fluorine , decrease adhesion, in spite DOC = 79011112 PAGE S4% of...small differences in the hardness of films on the basis of the fluorine -bearing polyol and generally accepted polyol. Is investigated the etfect ot...polyurethane, to rigid surface. DOC 79011112 P A * S The effect of the solvent, utilized for obtaining the varnish , on adhesion is investigated in

  12. Efficient Synthesis of Spirobarbiturates and Spirothiobarbiturates Bearing Cyclopropane Rings by Rhodium(II)-Catalyzed Reactions of Cyclic Diazo Compounds

    International Nuclear Information System (INIS)

    Wang, Xue; Lee, Yong Rok

    2013-01-01

    Rhodium(II)-catalyzed reactions of cyclic diazo compounds derived from barbituric acid and thiobarbituric acid with a variety of styrene moieties were examined. These reactions provide rapid synthetic routes to the preparations of spirobarbiturates and spirothiobarbiturates bearing cyclopropane rings

  13. Efficient Synthesis of Spirobarbiturates and Spirothiobarbiturates Bearing Cyclopropane Rings by Rhodium(II)-Catalyzed Reactions of Cyclic Diazo Compounds

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xue; Lee, Yong Rok [Yeungnam Univ., Gyeongsan (Korea, Republic of)

    2013-06-15

    Rhodium(II)-catalyzed reactions of cyclic diazo compounds derived from barbituric acid and thiobarbituric acid with a variety of styrene moieties were examined. These reactions provide rapid synthetic routes to the preparations of spirobarbiturates and spirothiobarbiturates bearing cyclopropane rings.

  14. 40 CFR Appendix Xiii to Part 266 - Mercury Bearing Wastes That May Be Processed in Exempt Mercury Recovery Units

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Mercury Bearing Wastes That May Be Processed in Exempt Mercury Recovery Units XIII Appendix XIII to Part 266 Protection of Environment... XIII to Part 266—Mercury Bearing Wastes That May Be Processed in Exempt Mercury Recovery Units These...

  15. Reproduce and die! Why aging? Part II

    NARCIS (Netherlands)

    Schuiling, GA

    Whilst in part I of this diptych on aging the question why aging exists at all is discussed; this part deals with the question which mechanisms underly aging and, ultimately, dying. It appears that aging is not just an active process as such - although all kinds of internal (e.g., oxigen-free

  16. Coal-fired power materials - Part II

    Energy Technology Data Exchange (ETDEWEB)

    Viswanathan, V.; Purgert, R.; Rawls, P. [Electric Power Research Institute, Palo Alto, CA (United States)

    2008-09-15

    Part 1 discussed some general consideration in selection of alloys for advanced ultra supercritical (USC) coal-fired power plant boilers. This second part covers results reported by the US project consortium, which has extensively evaluated the steamside oxidation, fireside corrosion, and fabricability of the alloys selected for USC plants. 3 figs.

  17. 78 FR 29702 - Ball Bearings and Parts Thereof From Germany: Final Results of Antidumping Duty Administrative...

    Science.gov (United States)

    2013-05-21

    ...On February 11, 2013, the Department of Commerce (the Department) published the preliminary results and partial rescission of its administrative review of the antidumping duty order on ball bearings and parts thereof from Germany. The period of review (POR) is May 1, 2011, through September 14, 2011.\\1\\ We received no comments from interested parties. Accordingly, for the final results we continue to find that subject merchandise has not been sold at less than normal value. ---------------------------------------------------------------------------

  18. Endemic pemphigus over a century: Part II.

    Science.gov (United States)

    Abréu-Vélez, Ana María; Roselino, Ana Maria; Howard, Michael S; Reason, Iara J de Messias

    2010-03-01

    Endemic pemphigus foliaceus (EPF) is an autoimmune disease, classically occurring in a restricted geographic area. Foci of EPF have been described in several Central and South American countries, often affecting young people and Amerindians, with some female predilection. Although most American EPF cases have been documented in Brazil, cases have been reported in Peru, Paraguay, El Salvador and Venezuela. An additional variant of EPF has been described in El Bagre, Colombia, (El Bagre-EPF) affecting older men and a few post-menopausal females. Finally, one additional type of EPF has been described in nomadic tribes affecting females of child bearing age in Tunisia, Africa. The main aim of this review is to summarize current knowledge about autoantigens, and immunologic and genetic studies in EPF. We utilized a retrospective review of the literature, aiming to compile and compare the multiple geographic foci of EPF. The primary autoantigens in EPF are still considered to be desmogleins in the case of the Tunisian and all American cases, in contradistinction to plakins and desmogleins in El Bagre-EPF. Although several autoantigens are been suggested, their biochemical nature needs further elucidation. Current knowledge still supports the concept that an antibody mediated immune response represents the principal pathophysiology in all variants of EPF. A strong genetic susceptibility appears to contribute to disease development in several people affected by these diseases; however, no specific genes have been confirmed at present. We conclude that further investigation is necessary to define these disorders immunologically and genetically.

  19. CHILD WELFARE IN CANADA : PART II

    OpenAIRE

    松本, 眞一; Shinichi, Matsumoto; 桃山学院大学社会学部

    2006-01-01

    This part study aims to research on the whole aspect of child protection in Canada. And so, this paper consists of five chapters as follows: (1)Canadian history of child protection, (2)definition of child abuse, (3)current situation of child protection in Canada, (4)outline of child protection and treatment, (5)triangular comparison of child protection and prevention in Canada, Australia and England. The first efforts at identifying and combating child abuse occurred in the latter part of the...

  20. The Influence of Injection Pockets on the Performance of Tilting-Pad Thrust Bearings: Part I – Theory

    DEFF Research Database (Denmark)

    Heinrichson, Niels; Santos, Ilmar

    2006-01-01

    This is Part I of a two-part series of papers describing the effects of high pressure injection pockets on the operating conditions of tilting-pad thrust bearings. A numerical model based on the Reynolds equation is developed extending the three dimensional thermo-elasto-hydrodynamic (TEHD......) analysis of tilting-pad thrust bearings to include the effects of high pressure injection and recesses in the bearing pad. The model is applied to the analysis of an existing bearing of large dimensions and the influence of the pocket is analyzed. It is shown that a shallow pocket positively influences...... the performance of the bearing as it has characteristics similar to those of a parallel step bearing....

  1. Evolution of major histocompatibility complex class I and class II genes in the brown bear

    Science.gov (United States)

    2012-01-01

    Background Major histocompatibility complex (MHC) proteins constitute an essential component of the vertebrate immune response, and are coded by the most polymorphic of the vertebrate genes. Here, we investigated sequence variation and evolution of MHC class I and class II DRB, DQA and DQB genes in the brown bear Ursus arctos to characterise the level of polymorphism, estimate the strength of positive selection acting on them, and assess the extent of gene orthology and trans-species polymorphism in Ursidae. Results We found 37 MHC class I, 16 MHC class II DRB, four DQB and two DQA alleles. We confirmed the expression of several loci: three MHC class I, two DRB, two DQB and one DQA. MHC class I also contained two clusters of non-expressed sequences. MHC class I and DRB allele frequencies differed between northern and southern populations of the Scandinavian brown bear. The rate of nonsynonymous substitutions (dN) exceeded the rate of synonymous substitutions (dS) at putative antigen binding sites of DRB and DQB loci and, marginally significantly, at MHC class I loci. Models of codon evolution supported positive selection at DRB and MHC class I loci. Both MHC class I and MHC class II sequences showed orthology to gene clusters found in the giant panda Ailuropoda melanoleuca. Conclusions Historical positive selection has acted on MHC class I, class II DRB and DQB, but not on the DQA locus. The signal of historical positive selection on the DRB locus was particularly strong, which may be a general feature of caniforms. The presence of MHC class I pseudogenes may indicate faster gene turnover in this class through the birth-and-death process. South–north population structure at MHC loci probably reflects origin of the populations from separate glacial refugia. PMID:23031405

  2. Evolution of major histocompatibility complex class I and class II genes in the brown bear

    Directory of Open Access Journals (Sweden)

    Kuduk Katarzyna

    2012-10-01

    Full Text Available Abstract Background Major histocompatibility complex (MHC proteins constitute an essential component of the vertebrate immune response, and are coded by the most polymorphic of the vertebrate genes. Here, we investigated sequence variation and evolution of MHC class I and class II DRB, DQA and DQB genes in the brown bear Ursus arctos to characterise the level of polymorphism, estimate the strength of positive selection acting on them, and assess the extent of gene orthology and trans-species polymorphism in Ursidae. Results We found 37 MHC class I, 16 MHC class II DRB, four DQB and two DQA alleles. We confirmed the expression of several loci: three MHC class I, two DRB, two DQB and one DQA. MHC class I also contained two clusters of non-expressed sequences. MHC class I and DRB allele frequencies differed between northern and southern populations of the Scandinavian brown bear. The rate of nonsynonymous substitutions (dN exceeded the rate of synonymous substitutions (dS at putative antigen binding sites of DRB and DQB loci and, marginally significantly, at MHC class I loci. Models of codon evolution supported positive selection at DRB and MHC class I loci. Both MHC class I and MHC class II sequences showed orthology to gene clusters found in the giant panda Ailuropoda melanoleuca. Conclusions Historical positive selection has acted on MHC class I, class II DRB and DQB, but not on the DQA locus. The signal of historical positive selection on the DRB locus was particularly strong, which may be a general feature of caniforms. The presence of MHC class I pseudogenes may indicate faster gene turnover in this class through the birth-and-death process. South–north population structure at MHC loci probably reflects origin of the populations from separate glacial refugia.

  3. Evolution of major histocompatibility complex class I and class II genes in the brown bear.

    Science.gov (United States)

    Kuduk, Katarzyna; Babik, Wiesław; Bojarska, Katarzyna; Sliwińska, Ewa B; Kindberg, Jonas; Taberlet, Pierre; Swenson, Jon E; Radwan, Jacek

    2012-10-02

    Major histocompatibility complex (MHC) proteins constitute an essential component of the vertebrate immune response, and are coded by the most polymorphic of the vertebrate genes. Here, we investigated sequence variation and evolution of MHC class I and class II DRB, DQA and DQB genes in the brown bear Ursus arctos to characterise the level of polymorphism, estimate the strength of positive selection acting on them, and assess the extent of gene orthology and trans-species polymorphism in Ursidae. We found 37 MHC class I, 16 MHC class II DRB, four DQB and two DQA alleles. We confirmed the expression of several loci: three MHC class I, two DRB, two DQB and one DQA. MHC class I also contained two clusters of non-expressed sequences. MHC class I and DRB allele frequencies differed between northern and southern populations of the Scandinavian brown bear. The rate of nonsynonymous substitutions (dN) exceeded the rate of synonymous substitutions (dS) at putative antigen binding sites of DRB and DQB loci and, marginally significantly, at MHC class I loci. Models of codon evolution supported positive selection at DRB and MHC class I loci. Both MHC class I and MHC class II sequences showed orthology to gene clusters found in the giant panda Ailuropoda melanoleuca. Historical positive selection has acted on MHC class I, class II DRB and DQB, but not on the DQA locus. The signal of historical positive selection on the DRB locus was particularly strong, which may be a general feature of caniforms. The presence of MHC class I pseudogenes may indicate faster gene turnover in this class through the birth-and-death process. South-north population structure at MHC loci probably reflects origin of the populations from separate glacial refugia.

  4. The Many Meanings of History, Part II

    Science.gov (United States)

    Szasz, Ferenc M.

    1974-01-01

    This article contains a collection of quotations about history collected by Professor Szasz. The first part of the collection appeared in the August 1974 issue of "The History Teacher." Readers are invited to send in other definitions they have found. (Author/RM)

  5. Cubby : Multiscreen Desktop VR Part II

    NARCIS (Netherlands)

    Gribnau, M.W.; Djajadiningrat, J.P.

    2000-01-01

    In this second part of our 'Cubby: Multiscreen Desktop VR' trilogy, we will introduce you to the art of creating a driver to read an Origin Instruments Dynasight input device. With the Dynasight, the position of the head of the user is established so that Cubby can display the correct images on its

  6. Plasma Astrophysics, part II Reconnection and Flares

    CERN Document Server

    Somov, Boris V

    2007-01-01

    This well-illustrated monograph is devoted to classic fundamentals, current practice, and perspectives of modern plasma astrophysics. The first part is unique in covering all the basic principles and practical tools required for understanding and working in plasma astrophysics. The second part presents the physics of magnetic reconnection and flares of electromagnetic origin in space plasmas within the solar system; single and double stars, relativistic objects, accretion disks, and their coronae are also covered. This book is designed mainly for professional researchers in astrophysics. However, it will also be interesting and useful to graduate students in space sciences, geophysics, as well as advanced students in applied physics and mathematics seeking a unified view of plasma physics and fluid mechanics.

  7. 46 CFR Table II to Part 150 - Grouping of Cargoes

    Science.gov (United States)

    2010-10-01

    ... solution Potassium oleate Potassium salt of polyolefin acid Propyl acetate Propylene carbonate Propylene... lignosulfonate solution Sodium polyacrylate solution 2 Sodium salt of Ferric hydroxyethylethylenediamine... 46 Shipping 5 2010-10-01 2010-10-01 false Grouping of Cargoes II Table II to Part 150 Shipping...

  8. 10 CFR Appendix II to Part 504 - Fuel Price Computation

    Science.gov (United States)

    2010-01-01

    ... DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS EXISTING POWERPLANTS Pt. 504, App. II Appendix II to Part... effects of future real price increases for each fuel. The delivered price of an alternate fuel used to calculate delivered fuel expenses must reflect the petitioner's delivered price of the alternate fuel and...

  9. LHC related projects and studies - Part (II)

    International Nuclear Information System (INIS)

    Rossi, L.; De Maria, R.

    2012-01-01

    The session was devoted to address some aspects of the HL-LHC (High Luminosity LHC) project and explore ideas on new machines for the long term future. The session had two parts. The former focused on some of the key issues of the HL-LHC projects: beam current limits, evolution of the collimation system, research plans for the interaction region magnets and crab cavities. The latter explored the ideas for the long term future projects (LHeC and HE-LHC) and how the current research-development program for magnets and RF structures could fit in the envisaged scenarios

  10. [Neurohumoral mechanisms for vasovagal syncopes. Part II].

    Science.gov (United States)

    Gajek, Jacek; Zyśko, Dorota

    2003-04-01

    Vasovagal syncope is defined as a reflex loss of consciousness related to reaction to various stimuli as orthostatic stress, pain or emotions connected with loss of muscle postural tone. In the second part of the paper the authors describe the possible role of the particular neurohumoral factors and autonomic nervous system in the development of vasovagal syncope. The studies on the involvement of neurohumoral factors in vasovagal syncope can play a key role in a more precise evaluation of affected patients, long term prophylaxis against syncopal events and may contribute to development of more reliable diagnostic tests.

  11. Drugs, money and society (Part II).

    Science.gov (United States)

    Walley, Tom

    2010-09-01

    Pharmacoeconomics started as marketing but has developed into a valuable tool in the fuller assessment of drug therapies. Its principles are now widely accepted, and many countries have government-funded agencies with responsibility for its application, most notably the National Institute for Health and Clinical Excellence in England. Many clinical pharmacologists are active in this area, and the discipline itself is part of the clinical pharmacology trainees' curriculum. Further developments will include value-based pricing and its use in cost sharing arrangements between health service and manufacturers.

  12. The sociogeometry of inequality: Part II

    Science.gov (United States)

    Eliazar, Iddo

    2015-05-01

    The study of socioeconomic inequality is of prime economic and social importance, and the key quantitative gauges of socioeconomic inequality are Lorenz curves and inequality indices - the most notable of the latter being the popular Gini index. In this series of papers we present a sociogeometric framework to the study of socioeconomic inequality. In this part we focus on the gap between the rich and the poor, which is quantified by gauges termed disparity curves. We shift from disparity curves to disparity sets, define inequality indices in terms of disparity sets, and introduce and explore a collection of distance-based and width-based inequality indices stemming from the geometry of disparity sets. We conclude with mean-absolute-deviation (MAD) representations of the inequality indices established in this series of papers, and with a comparison of these indices to the popular Gini index.

  13. Has the tsunami arrived? Part II.

    Science.gov (United States)

    Halverson, Dean; Glowac, Wayne

    2009-01-01

    Healthcare is an industry in the midst of significant change. After years of double-digit cost increases, the system has reached a tipping point. Where once only employers were heard crying out for change, the call is now coming from all levels of American society. The voice that is most important to effect change is the newest--that of the consumer. In part two of our overview of the healthcare tsunami, we hope to offer you some insights and practical ideas on how to improve the return on investment of your marketing. We believe those who work to understand the new market forces and react with insight will not just survive during the tsunami, they will thrive.

  14. [Conceptual Development in Cognitive Science. Part II].

    Science.gov (United States)

    Fierro, Marco

    2012-03-01

    Cognitive science has become the most influential paradigm on mental health in the late 20(th) and the early 21(st) centuries. In few years, the concepts, problem approaches and solutions proper to this science have significantly changed. Introduction and discussion of the fundamental concepts of cognitive science divided in four stages: Start, Classic Cognitivism, Connectionism, and Embodying / Enacting. The 2(nd) Part of the paper discusses the above mentioned fourth stage and explores the clinical setting, especially in terms of cognitive psychotherapy. The embodying/enacting stage highlights the role of the body including a set of determined evolutionary movements which provide a way of thinking and exploring the world. The performance of cognitive tasks is considered as a process that uses environmental resources that enhances mental skills and deploys them beyond the domestic sphere of the brain. On the other hand, body and mind are embedded in the world, thus giving rise to cognition when interacting, a process known as enacting. There is a close connection between perception and action, hence the interest in real-time interactions with the world rather than abstract reasoning. Regarding clinics, specifically the cognitive therapy, there is little conceptual discussion maybe due to good results from practice that may led us to consider that theoretical foundations are firm and not problem-raising. Copyright © 2012 Asociación Colombiana de Psiquiatría. Publicado por Elsevier España. All rights reserved.

  15. Compressor Part II: Volute Flow Predictions

    Directory of Open Access Journals (Sweden)

    Yu-Tai Lee

    1999-01-01

    Full Text Available A numerical method that solves the Reynolds-averaged Navier-Stokes equations is used to study an inefficient component of a shipboard air-conditioning HCFC-124 compressor system. This high-loss component of the centrifugal compressor was identified as the volute through a series of measurements given in Part I of the paper. The predictions were made using three grid topologies. The first grid closes the connection between the cutwater and the discharge diffuser. The other two grids connect the cutwater area with the discharge diffuser. Experiments were performed to simulate both the cutwater conditions used in the predictions. Surface pressures along the outer wall and near the inlet of the volute were surveyed for comparisons with the predictions. Good agreements between the predicted results and the measurements validate the calculations. Total pressure distributions and flow stream traces from the prediction results support the loss distribution through the volute. A modified volute configuration is examined numerically for further loss comparison.

  16. Calculus of Elementary Functions, Part II. Teacher's Commentary. Revised Edition.

    Science.gov (United States)

    Herriot, Sarah T.; And Others

    This course is intended for students who have a thorough knowledge of college preparatory mathematics, including algebra, axiomatic geometry, trigonometry, and analytic geometry. This teacher's guide is for Part II of the course. It is designed to follow Part I of the text. The guide contains background information, suggested instructional…

  17. Calculus of Elementary Functions, Part II. Student Text. Revised Edition.

    Science.gov (United States)

    Herriot, Sarah T.; And Others

    This course is intended for students who have a thorough knowledge of college preparatory mathematics, including algebra, axiomatic geometry, trigonometry, and analytic geometry. This text, Part II, contains material designed to follow Part I. Chapters included in this text are: (6) Derivatives of Exponential and Related Functions; (7) Area and…

  18. Kick, Glide, Pole! Cross-Country Skiing Fun (Part II)

    Science.gov (United States)

    Duoos, Bridget A.

    2012-01-01

    Part I of Kick, Glide, Pole! Cross-Country Skiing Fun, which was published in last issue, discussed how to select cross-country ski equipment, dress for the activity and the biomechanics of the diagonal stride. Part II focuses on teaching the diagonal stride technique and begins with a progression of indoor activities. Incorporating this fun,…

  19. Finite Element Analysis of the Effect on Edge Distance of the Tensile Bearing Capacity of Embedded Hanging Parts

    Directory of Open Access Journals (Sweden)

    Meng Xian Hong

    2016-01-01

    Full Text Available In order to explore the trend of tensile bearing capacity of embedded hanging parts when change the edge distance. Based on the finite element analysis software ABAQUS, the four simulation model was established. The buried depth and strength of concrete remain unchanged, but the edge distance was gradient change. By the load - displacement curve of every model known, the greater the edge distance, the greater the bearing capacity. When the edge distance reaches 1.5 times buried depth, the effect of increasing edge distance for improving the bearing capacity will be impaired.

  20. Recent Economic Perspectives on Political Economy, Part II*

    Science.gov (United States)

    Dewan, Torun; Shepsle, Kenneth A.

    2013-01-01

    In recent years some of the best theoretical work on the political economy of political institutions and processes has begun surfacing outside the political science mainstream in high quality economics journals. This two-part paper surveys these contributions from a recent five-year period. In Part I, the focus is on elections, voting and information aggregation, followed by treatments of parties, candidates, and coalitions. In Part II, papers on economic performance and redistribution, constitutional design, and incentives, institutions, and the quality of political elites are discussed. Part II concludes with a discussion of the methodological bases common to economics and political science, the way economists have used political science research, and some new themes and arbitrage opportunities. PMID:23606754

  1. Nursing Care of Patients Undergoing Chemotherapy Desensitization: Part II.

    Science.gov (United States)

    Jakel, Patricia; Carsten, Cynthia; Carino, Arvie; Braskett, Melinda

    2016-04-01

    Chemotherapy desensitization protocols are safe, but labor-intensive, processes that allow patients with cancer to receive medications even if they initially experienced severe hypersensitivity reactions. Part I of this column discussed the pathophysiology of hypersensitivity reactions and described the development of desensitization protocols in oncology settings. Part II incorporates the experiences of an academic medical center and provides a practical guide for the nursing care of patients undergoing chemotherapy desensitization.
.

  2. Methods of humidity determination Part II: Determination of material humidity

    OpenAIRE

    Rübner, Katrin; Balköse, Devrim; Robens, E.

    2008-01-01

    Part II covers the most common methods of measuring the humidity of solid material. State of water near solid surfaces, gravimetric measurement of material humidity, measurement of water sorption isotherms, chemical methods for determination of water content, measurement of material humidity via the gas phase, standardisation, cosmonautical observations are reviewed.

  3. 77 FR 2031 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Science.gov (United States)

    2012-01-13

    ... Parts Thereof, Finished and Unfinished From the People's Republic of China: Extension of the Time Limit..., International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue NW..., finished and unfinished from the People's Republic of China. See Tapered Roller Bearings and Parts Thereof...

  4. 76 FR 35401 - Ball Bearings and Parts Thereof From Japan and the United Kingdom: Notice of Court Decision Not...

    Science.gov (United States)

    2011-06-17

    ...On June 1, 2005, the Department of Commerce (the Department) initiated and the International Trade Commission (ITC) instituted the second sunset reviews of the antidumping duty orders on ball bearings and parts thereof from Japan and the United Kingdom. On April 20, 2011, the Court of International Trade (CIT) entered its final judgment sustaining the ITC's remand redetermination that revocation of the antidumping duty orders on ball bearings and parts thereof from Japan and the United Kingdom would not be likely to lead to continuation or recurrence of material injury to an industry in the United States within a reasonably foreseeable time.

  5. 76 FR 57019 - Ball Bearings and Parts Thereof From France, Germany and Italy: Final Results of Sunset Reviews...

    Science.gov (United States)

    2011-09-15

    ...On August 1, 2011, the Department of Commerce (the Department) initiated the sunset reviews of the antidumping duty orders on ball bearings and parts thereof from France, Germany, and Italy. See Initiation of Five-Year (``Sunset'') Review, 76 FR 45778 (August 1, 2011) (Initiation Notice). Because no domestic interested party filed a notice of intent to participate in response to the notice of initiation of the sunset reviews by the applicable deadline, the Department is revoking the antidumping duty orders on ball bearings and parts thereof from France, Germany, and Italy.

  6. HERBICIDAS INIBIDORES DO FOTOSSISTEMA IIPARTE I /\tPHOTOSYSTEM II INHIBITOR HERBICIDES - PART I

    Directory of Open Access Journals (Sweden)

    ILCA P. DE F. E SILVA

    2013-11-01

    Full Text Available O controle químico tem sido o mais utilizado em grandes áreas de plantio, principalmente por ser um método rápido e eficiente. Os herbicidas inibidores do fotossistema II (PSII são fundamentais para o manejo integrado de plantas daninhas e práticas conservacionista de solo. A aplicação é realizada em pré-emergência ou pós-emergência inicial das plantas daninhas. A absorção é pelas raízes, tendo como barreira as estrias de Caspari, sendo a translocação realizada pelo xilema. O processo de absorção e translocação também são dependentes das próprias características do produto, como as propriedades lipofílicas e hidrofílicas, as quais podem ser medidas através do coeficiente de partição octanol-água (Kow. A inibição da fotossíntese acontece pela ligação dos herbicidas deste grupo ao sítio de ligação da QB, na proteína D1 do fotossistema II, o qual se localiza na membrana dos tilacóides dos cloroplastos, causando, o bloqueia do transporte de elétrons da QA para QB, interrompendo a fixação do CO2 e a produção de ATP e NAPH2.

  7. Novel High Temperature Magnetic Bearings for Space Vehicle Systems, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Previous high temperature magnetic bearings employed electromagnets only. The work proposed in this SBIR program seeks to utilize High Temperature Permanent Magnets...

  8. First international 26Al interlaboratory comparison - Part II

    International Nuclear Information System (INIS)

    Merchel, Silke; Bremser, Wolfram

    2005-01-01

    After finishing Part I of the first international 26 Al interlaboratory comparison with accelerator mass spectrometry (AMS) laboratories [S. Merchel, W. Bremser, Nucl. Instr. and Meth. B 223-224 (2004) 393], the evaluation of Part II with radionuclide counting laboratories took place. The evaluation of the results of the seven participating laboratories on four meteorite samples shows a good overall agreement between laboratories, i.e. it does not reveal any statistically significant differences if results are compared sample-by-sample. However, certain interlaboratory bias is observed with a more detailed statistical analysis including some multivariate approaches

  9. Redistribution of elements between wastes and organic-bearing material in the dispersion train of gold-bearing sulfide tailings: Part I. Geochemistry and mineralogy.

    Science.gov (United States)

    Saryg-Ool, B Yu; Myagkaya, I N; Kirichenko, I S; Gustaytis, M A; Shuvaeva, O V; Zhmodik, S M; Lazareva, E V

    2017-03-01

    Migration and redistribution of elements during prolonged interaction of cyanide wastes with the underlying natural organic-bearing material have been studied in two ~40cm deep cores that sample primary ores and their weathering profile (wastes I and II, respectively) in the dispersion train of gold-bearing sulfide tailings in Siberia. Analytical results of SR-XRF, whole-rock XRF, AAS, CHNS, and SEM measurements of core samples show high K, Sr, Ti, and Fe enrichments and correlation of P 2 O 5 and Mn with LOI and C org . Organic material interlayered or mixed with the wastes accumulates Cu, Zn, Se, Cd, Ag, Au, and Hg. The peat that contacts wastes II bears up to 3wt.% Zn, 1000g/t Se, 100g/t Cd, and 8000g/t Hg. New phases of Zn and Hg sulfides and Hg selenides occur as abundant sheaths over bacterial cells suggesting microbial mediation in sorption of elements. Organic-bearing material in the cores contains 10-30g/t Au in 2-5cm thick intervals, both within and outside the intervals rich in sulfides and selenides. Most of gold is invisible but reaches 345g/t and forms 50nm to 1.5μm Au 0 particles in a thin 2-3cm interval of organic remnants mixed with wastes I. Vertical and lateral infiltration of AMD waters in peat and oxidative dissolution of wastes within the dispersion train of the Ursk tailings lead to redistribution of elements and their accumulation by combined physical (material's permeability, direction AMD), chemical (complexing, sorption by organic matter and Fe(III) hydroxides) and biochemical (metabolism of sulfate-reducing bacteria) processes. The accumulated elements form secondary sulfates, and Hg and Zn selenides. The results provide insights into accumulation of elements in the early history of coal and black shale deposits and have implications for remediation of polluted areas and for secondary enrichment technologies. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Fungal oxidative dissolution of the Mn(II)-bearing mineral rhodochrosite and the role of metabolites in manganese oxide formation.

    Science.gov (United States)

    Tang, Yuanzhi; Zeiner, Carolyn A; Santelli, Cara M; Hansel, Colleen M

    2013-04-01

    Microbially mediated oxidation of Mn(II) to Mn(III/IV) oxides influences the cycling of metals and remineralization of carbon. Despite the prevalence of Mn(II)-bearing minerals in nature, little is known regarding the ability of microbes to oxidize mineral-hosted Mn(II). Here, we explored oxidation of the Mn(II)-bearing mineral rhodochrosite (MnCO3 ) and characteristics of ensuing Mn oxides by six Mn(II)-oxidizing Ascomycete fungi. All fungal species substantially enhanced rhodochrosite dissolution and surface modification. Mineral-hosted Mn(II) was oxidized resulting in formation of Mn(III/IV) oxides that were all similar to δ-MnO2 but varied in morphology and distribution in relation to cellular structures and the MnCO3 surface. For four fungi, Mn(II) oxidation occurred along hyphae, likely mediated by cell wall-associated proteins. For two species, Mn(II) oxidation occurred via reaction with fungal-derived superoxide produced at hyphal tips. This pathway ultimately resulted in structurally unique Mn oxide clusters formed at substantial distances from any cellular structure. Taken together, findings for these two fungi strongly point to a role for fungal-derived organic molecules in Mn(III) complexation and Mn oxide templation. Overall, this study illustrates the importance of fungi in rhodochrosite dissolution, extends the relevance of biogenic superoxide-based Mn(II) oxidation and highlights the potential role of mycogenic exudates in directing mineral precipitation. © 2012 Society for Applied Microbiology and Blackwell Publishing Ltd.

  11. Active lubrication applied to radial gas journal bearings. Part 1: Modeling

    DEFF Research Database (Denmark)

    Morosi, Stefano; Santos, Ilmar

    2011-01-01

    Active bearings represent a mechatronic answer to the growing industrial need to high performance turbomachinery. The present contribution aims at demonstrate the feasibility of applying active lubrication to gas journal bearings. The principle of operation is to generate active forces by regulat...

  12. 75 FR 26920 - Ball Bearings and Parts Thereof from France, Germany, Italy, Japan, and the United Kingdom...

    Science.gov (United States)

    2010-05-13

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801, A-588-804, A-412-801] Ball Bearings and Parts Thereof from France, Germany, Italy, Japan, and the United Kingdom: Preliminary Results of Antidumping Duty Administrative Reviews, Preliminary Results of Changed-Circumstances Review, Rescission of Antidumpin...

  13. 77 FR 16537 - Ball Bearings and Parts Thereof from France, Germany, and Italy: Extension of Time Limit for...

    Science.gov (United States)

    2012-03-21

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801] Ball Bearings and Parts Thereof from France, Germany, and Italy: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative Reviews AGENCY: Import Administration, International Trade Administration, Department of Commerce. DATES:...

  14. 77 FR 75973 - Ball Bearings and Parts Thereof From France, Germany, and Italy: Final Results of Antidumping...

    Science.gov (United States)

    2012-12-26

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801] Ball Bearings and Parts Thereof From France, Germany, and Italy: Final Results of Antidumping Duty Administrative Reviews; 2010-2011 Correction In notice document 2012-29770, appearing on pages 73415-73417 in the issue of Monday, December 10, 2012, make...

  15. 76 FR 2647 - Ball Bearings and Parts Thereof From France, Germany, Italy, Japan, and the United Kingdom...

    Science.gov (United States)

    2011-01-14

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801, A-588-804, A-412-801] Ball Bearings and Parts Thereof From France, Germany, Italy, Japan, and the United Kingdom: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative Reviews AGENCY: Import Administration, International Trade...

  16. 77 FR 2511 - Ball Bearings and Parts Thereof From France, Germany, and Italy: Extension of Time Limit for...

    Science.gov (United States)

    2012-01-18

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801] Ball Bearings and Parts Thereof From France, Germany, and Italy: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative Reviews AGENCY: Import Administration, International Trade Administration, Department of Commerce. DATES:...

  17. 76 FR 58768 - Ball Bearings and Parts Thereof From France, Germany, and Italy; Amended Final Results of...

    Science.gov (United States)

    2011-09-22

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801] Ball Bearings and Parts Thereof From France, Germany, and Italy; Amended Final Results of Antidumping Administrative Reviews AGENCY: Import Administration, International Trade Administration, Department of Commerce EFFECTIVE DATE: September 22, 2011. FOR...

  18. 75 FR 2108 - Ball Bearings and Parts Thereof from France, Germany, Italy, Japan, and the United Kingdom...

    Science.gov (United States)

    2010-01-14

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801, A-588-804, A-412-801] Ball Bearings and Parts Thereof from France, Germany, Italy, Japan, and the United Kingdom: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative Reviews AGENCY: Import Administration, International Trade...

  19. 76 FR 15940 - Ball Bearings and Parts Thereof From France, Germany, Italy, Japan, and the United Kingdom...

    Science.gov (United States)

    2011-03-22

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-427-801, A-428-801, A-475-801, A-588-804, A-412-801] Ball Bearings and Parts Thereof From France, Germany, Italy, Japan, and the United Kingdom: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative and Changed-Circumstances Reviews AGENCY: Import...

  20. 76 FR 76143 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Science.gov (United States)

    2011-12-06

    ..., the United Steel, Paper and Forestry, Rubber, Manufacturing, Energy, Allied Industrial and Service... manufacturing of tapered roller bearings and parts thereof in the United States, also notified the Department... manufacturing the domestic like product, and therefore, is an interested party pursuant to section 771(9)(D) of...

  1. Healing and relaxation in flows of helium II. Part II. First, second, and fourth sound

    International Nuclear Information System (INIS)

    Hills, R.N.; Roberts, P.H.

    1978-01-01

    In Part I of this series, a theory of helium II incorporating the effects of quantum healing and relaxation was developed. In this paper, the propagation of first, second, and fourth sound is discussed. Particular attention is paid to sound propagation in the vicinity of the lambda point where the effects of relaxation and quantum healing become important

  2. Shock Hazard Prevention through Self-Healing Insulative Coating on SSA Metallic Bearings, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — The space suit assembly (SSA) contains metallic bearings at the wrist, neck, and waist, which are exposed to space environment, and pose a potential shock hazard....

  3. Uranium in minerals of gold-bearing formations of the North-Eastern part of the USSR

    International Nuclear Information System (INIS)

    Zagruzina, I.A.; Pinsky, E.M.

    1979-01-01

    Uranium concentration in 2190 mineral grains from 23 gold-bearing veins of different age deposits in the North-Eastern part of the USSR have been determined using f-radiography. The deposits studied are referred to two formation types: gold-silver epithermal and gold-quartz mesothermal. Differences in physico-chemical conditions of deposite formation of the above formation types are emphasized by the differences in uranium concentration in the vein minerals: 1.0-1.4 g/tU in the first type and 0.4 g/tU in the second one. Uranium content in minerals of gold-bearing veins as compared to minerals of other deposits is characterized by the lowest concentrations. In all gold-bearing veins hydrooxides of iron and hydromica are the main concentrators of uranium. Hypergene stage plays dominating role in uranium accumulation

  4. MHC class II DQB diversity in the Japanese black bear, Ursus thibetanus japonicus.

    Science.gov (United States)

    Yasukochi, Yoshiki; Kurosaki, Toshifumi; Yoneda, Masaaki; Koike, Hiroko; Satta, Yoko

    2012-11-29

    The major histocompatibility complex (MHC) genes are one of the most important genetic systems in the vertebrate immune response. The diversity of MHC genes may directly influence the survival of individuals against infectious disease. However, there has been no investigation of MHC diversity in the Asiatic black bear (Ursus thibetanus). Here, we analyzed 270-bp nucleotide sequences of the entire exon 2 region of the MHC DQB gene by using 188 samples from the Japanese black bear (Ursus thibetanus japonicus) from 12 local populations. Among 185 of 188 samples, we identified 44 MHC variants that encoded 31 different amino acid sequences (allotypes) and one putative pseudogene. The phylogenetic analysis suggests that MHC variants detected from the Japanese black bear are derived from the DQB locus. One of the 31 DQB allotypes, Urth-DQB*01, was found to be common to all local populations. Moreover, this allotype was shared between the black bear on the Asian continent and the Japanese black bear, suggesting that Urth-DQB*01 might have been maintained in the ancestral black bear population for at least 300,000 years. Our findings, from calculating the ratio of non-synonymous to synonymous substitutions, indicate that balancing selection has maintained genetic variation of peptide-binding residues at the DQB locus of the Japanese black bear. From examination of genotype frequencies among local populations, we observed a considerably lower level of observed heterozygosity than expected. The low level of observed heterozygosity suggests that genetic drift reduced DQB diversity in the Japanese black bear due to a bottleneck event at the population or species level. The decline of DQB diversity might have been accelerated by the loss of rare variants that have been maintained by negative frequency-dependent selection. Nevertheless, DQB diversity of the black bear appears to be relatively high compared with some other endangered mammalian species. This result suggests that

  5. MHC class II DQB diversity in the Japanese black bear, Ursus thibetanus japonicus

    Science.gov (United States)

    2012-01-01

    Background The major histocompatibility complex (MHC) genes are one of the most important genetic systems in the vertebrate immune response. The diversity of MHC genes may directly influence the survival of individuals against infectious disease. However, there has been no investigation of MHC diversity in the Asiatic black bear (Ursus thibetanus). Here, we analyzed 270-bp nucleotide sequences of the entire exon 2 region of the MHC DQB gene by using 188 samples from the Japanese black bear (Ursus thibetanus japonicus) from 12 local populations. Results Among 185 of 188 samples, we identified 44 MHC variants that encoded 31 different amino acid sequences (allotypes) and one putative pseudogene. The phylogenetic analysis suggests that MHC variants detected from the Japanese black bear are derived from the DQB locus. One of the 31 DQB allotypes, Urth-DQB*01, was found to be common to all local populations. Moreover, this allotype was shared between the black bear on the Asian continent and the Japanese black bear, suggesting that Urth-DQB*01 might have been maintained in the ancestral black bear population for at least 300,000 years. Our findings, from calculating the ratio of non-synonymous to synonymous substitutions, indicate that balancing selection has maintained genetic variation of peptide-binding residues at the DQB locus of the Japanese black bear. From examination of genotype frequencies among local populations, we observed a considerably lower level of observed heterozygosity than expected. Conclusions The low level of observed heterozygosity suggests that genetic drift reduced DQB diversity in the Japanese black bear due to a bottleneck event at the population or species level. The decline of DQB diversity might have been accelerated by the loss of rare variants that have been maintained by negative frequency-dependent selection. Nevertheless, DQB diversity of the black bear appears to be relatively high compared with some other endangered mammalian

  6. MHC class II DQB diversity in the Japanese black bear, Ursus thibetanus japonicus

    Directory of Open Access Journals (Sweden)

    Yasukochi Yoshiki

    2012-11-01

    Full Text Available Abstract Background The major histocompatibility complex (MHC genes are one of the most important genetic systems in the vertebrate immune response. The diversity of MHC genes may directly influence the survival of individuals against infectious disease. However, there has been no investigation of MHC diversity in the Asiatic black bear (Ursus thibetanus. Here, we analyzed 270-bp nucleotide sequences of the entire exon 2 region of the MHC DQB gene by using 188 samples from the Japanese black bear (Ursus thibetanus japonicus from 12 local populations. Results Among 185 of 188 samples, we identified 44 MHC variants that encoded 31 different amino acid sequences (allotypes and one putative pseudogene. The phylogenetic analysis suggests that MHC variants detected from the Japanese black bear are derived from the DQB locus. One of the 31 DQB allotypes, Urth-DQB*01, was found to be common to all local populations. Moreover, this allotype was shared between the black bear on the Asian continent and the Japanese black bear, suggesting that Urth-DQB*01 might have been maintained in the ancestral black bear population for at least 300,000 years. Our findings, from calculating the ratio of non-synonymous to synonymous substitutions, indicate that balancing selection has maintained genetic variation of peptide-binding residues at the DQB locus of the Japanese black bear. From examination of genotype frequencies among local populations, we observed a considerably lower level of observed heterozygosity than expected. Conclusions The low level of observed heterozygosity suggests that genetic drift reduced DQB diversity in the Japanese black bear due to a bottleneck event at the population or species level. The decline of DQB diversity might have been accelerated by the loss of rare variants that have been maintained by negative frequency-dependent selection. Nevertheless, DQB diversity of the black bear appears to be relatively high compared with some other

  7. 40 CFR Appendix B to Part 414 - Complexed Metal-Bearing Waste Streams

    Science.gov (United States)

    2010-07-01

    ... 414—Complexed Metal-Bearing Waste Streams Chromium Azo dye intermediates/Substituted diazonium salts + coupling compounds Vat dyes Acid dyes Azo dyes, metallized/Azo dye + metal acetate Acid dyes, Azo...

  8. Polycystic ovary syndrome: a review for dermatologists: Part II. Treatment.

    Science.gov (United States)

    Buzney, Elizabeth; Sheu, Johanna; Buzney, Catherine; Reynolds, Rachel V

    2014-11-01

    Dermatologists are in a key position to treat the manifestations of polycystic ovary syndrome (PCOS). The management of PCOS should be tailored to each woman's specific goals, reproductive interests, and particular constellation of symptoms. Therefore, a multidisciplinary approach is recommended. In part II of this continuing medical education article, we present the available safety and efficacy data regarding treatments for women with acne, hirsutism, and androgenetic alopecia. Therapies discussed include lifestyle modification, topical therapies, combined oral contraceptives, antiandrogen agents, and insulin-sensitizing drugs. Treatment recommendations are made based on the current available evidence. Copyright © 2014 American Academy of Dermatology, Inc. Published by Elsevier Inc. All rights reserved.

  9. Impedance-Source Networks for Electric Power Conversion Part II

    DEFF Research Database (Denmark)

    Siwakoti, Yam P.; Peng, Fang Zheng; Blaabjerg, Frede

    2015-01-01

    Impedance-source networks cover the entire spectrum of electric power conversion applications (dc-dc, dc-ac, ac-dc, ac-ac) controlled and modulated by different modulation strategies to generate the desired dc or ac voltage and current at the output. A comprehensive review of various impedance......-source-network-based power converters has been covered in a previous paper and main topologies were discussed from an application point of view. Now Part II provides a comprehensive review of the most popular control and modulation strategies for impedance-source network-based power converters/inverters. These methods...

  10. Signs of revision in Don Quixote, Part II

    Directory of Open Access Journals (Sweden)

    Gonzalo Pontón

    2016-11-01

    Full Text Available This article provides new evidences in favour of the hypothesis that Cervantes, after finishing Don Quixote, Part II, partially revised the original, introducing some significant changes and additions, mainly in the last chapters. The analysis of some narrative inconsistencies, that cannot be interpreted as mere mistakes but as significant textual traces, reveals a process of re-elaboration –a process that affects at least four sections of the novel. Most of the evidence gathered here suggests that this revision is closely linked to Avellaneda’s continuation, in the sense that Cervantes tried to challenge the apocriphal Quixote making last-time interventions in his own text.

  11. Sampling and analysis plan for phase II of the Bear Creek Valley treatability study Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1997-05-01

    The Bear Creek Valley (BCV) Treatability Study is intended to provide site-specific data defining potential treatment technologies applicable to contaminated groundwater and surface water. This project directly supports Alternative 5 of the base action in the BCV Feasibility Study, and indirectly supports other alternatives through proof of concept. In that role, the ultimate goal is to install a treatment system that will remove uranium and nitrate from groundwater before it reaches Bear Creek. A secondary goal is the concurrent removal of technetium and several metals that impact ecological risk. This project is intended to produce hydraulic and treatment performance data required to design the treatment system to reach those goals. This project will also generate information that can be applied at other facilities within the Oak Ridge Reservation. This report is the sampling and analysis plan (SAP) for the field work component of Phase II of the BCV Treatability Study. Field work for this phase of the BCV Treatability Study consists of media testing. In-field continuous flow tests will be conducted over an extended time period (5 weeks) to generate data on long-term treatment effects on potential treatment media including sorbents and zero valent iron, over 28 weeks for constructed wetlands treatment, and over 24 weeks for algal mats treatment. The SAP addresses environmental sampling at the S-3 Site at the Oak Ridge Y-12 Plant. Samples will be taken from groundwater, effluent from test columns, effluent from an algal mat reactor, and effluent from a pilot-scale wetlands. This plan will be implemented as part of the BCV Phase II Treatability Study Best Management Practices Plan and in conjunction with the BCV Phase II Treatability Study Health and Safety Plan and the BCV Phase II Treatability Study Waste Management Plan

  12. The "Pseudocommando" mass murderer: part II, the language of revenge.

    Science.gov (United States)

    Knoll, James L

    2010-01-01

    In Part I of this article, research on pseudocommandos was reviewed, and the important role that revenge fantasies play in motivating such persons to commit mass murder-suicide was discussed. Before carrying out their mass shootings, pseudocommandos may communicate some final message to the public or news media. These communications are rich sources of data about their motives and psychopathology. In Part II of this article, forensic psycholinguistic analysis is applied to clarify the primary motivations, detect the presence of mental illness, and discern important individual differences in the final communications of two recent pseudocommandos: Seung-Hui Cho (Virginia Tech) and Jiverly Wong (Binghamton, NY). Although both men committed offenses that qualify them as pseudocommandos, their final communications reveal striking differences in their psychopathology.

  13. Structure Learning and Statistical Estimation in Distribution Networks - Part II

    Energy Technology Data Exchange (ETDEWEB)

    Deka, Deepjyoti [Univ. of Texas, Austin, TX (United States); Backhaus, Scott N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chertkov, Michael [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-02-13

    Limited placement of real-time monitoring devices in the distribution grid, recent trends notwithstanding, has prevented the easy implementation of demand-response and other smart grid applications. Part I of this paper discusses the problem of learning the operational structure of the grid from nodal voltage measurements. In this work (Part II), the learning of the operational radial structure is coupled with the problem of estimating nodal consumption statistics and inferring the line parameters in the grid. Based on a Linear-Coupled(LC) approximation of AC power flows equations, polynomial time algorithms are designed to identify the structure and estimate nodal load characteristics and/or line parameters in the grid using the available nodal voltage measurements. Then the structure learning algorithm is extended to cases with missing data, where available observations are limited to a fraction of the grid nodes. The efficacy of the presented algorithms are demonstrated through simulations on several distribution test cases.

  14. CE and nanomaterials - Part II: Nanomaterials in CE.

    Science.gov (United States)

    Adam, Vojtech; Vaculovicova, Marketa

    2017-10-01

    The scope of this two-part review is to summarize publications dealing with CE and nanomaterials together. This topic can be viewed from two broad perspectives, and this article is trying to highlight these two approaches: (i) CE of nanomaterials, and (ii) nanomaterials in CE. The second part aims at summarization of publications dealing with application of nanomaterials for enhancement of CE performance either in terms of increasing the separation resolution or for improvement of the detection. To increase the resolution, nanomaterials are employed as either surface modification of the capillary wall forming open tubular column or as additives to the separation electrolyte resulting in a pseudostationary phase. Moreover, nanomaterials have proven to be very beneficial for increasing also the sensitivity of detection employed in CE or even they enable the detection (e.g., fluorescent tags of nonfluorescent molecules). © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. PREREM: an interactive data preprocessing code for INREM II. Part I: user's manual. Part II: code structure

    Energy Technology Data Exchange (ETDEWEB)

    Ryan, M.T.; Fields, D.E.

    1981-05-01

    PREREM is an interactive computer code developed as a data preprocessor for the INREM-II (Killough, Dunning, and Pleasant, 1978a) internal dose program. PREREM is intended to provide easy access to current and self-consistent nuclear decay and radionuclide-specific metabolic data sets. Provision is made for revision of metabolic data, and the code is intended for both production and research applications. Documentation for the code is in two parts. Part I is a user's manual which emphasizes interpretation of program prompts and choice of user input. Part II stresses internal structure and flow of program control and is intended to assist the researcher who wishes to revise or modify the code or add to its capabilities. PREREM is written for execution on a Digital Equipment Corporation PDP-10 System and much of the code will require revision before it can be run on other machines. The source program length is 950 lines (116 blocks) and computer core required for execution is 212 K bytes. The user must also have sufficient file space for metabolic and S-factor data sets. Further, 64 100 K byte blocks of computer storage space are required for the nuclear decay data file. Computer storage space must also be available for any output files produced during the PREREM execution. 9 refs., 8 tabs.

  16. 40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery Furnaces XII Appendix XII to Part 266... FACILITIES Pt. 266, App. XII Appendix XII to Part 266—Nickel or Chromium-Bearing Materials that may be...

  17. Blade System Design Study. Part II, final project report (GEC).

    Energy Technology Data Exchange (ETDEWEB)

    Griffin, Dayton A. (DNV Global Energy Concepts Inc., Seattle, WA)

    2009-05-01

    As part of the U.S. Department of Energy's Low Wind Speed Turbine program, Global Energy Concepts LLC (GEC)1 has studied alternative composite materials for wind turbine blades in the multi-megawatt size range. This work in one of the Blade System Design Studies (BSDS) funded through Sandia National Laboratories. The BSDS program was conducted in two phases. In the Part I BSDS, GEC assessed candidate innovations in composite materials, manufacturing processes, and structural configurations. GEC also made recommendations for testing composite coupons, details, assemblies, and blade substructures to be carried out in the Part II study (BSDS-II). The BSDS-II contract period began in May 2003, and testing was initiated in June 2004. The current report summarizes the results from the BSDS-II test program. Composite materials evaluated include carbon fiber in both pre-impregnated and vacuum-assisted resin transfer molding (VARTM) forms. Initial thin-coupon static testing included a wide range of parameters, including variation in manufacturer, fiber tow size, fabric architecture, and resin type. A smaller set of these materials and process types was also evaluated in thin-coupon fatigue testing, and in ply-drop and ply-transition panels. The majority of materials used epoxy resin, with vinyl ester (VE) resin also used for selected cases. Late in the project, testing of unidirectional fiberglass was added to provide an updated baseline against which to evaluate the carbon material performance. Numerous unidirectional carbon fabrics were considered for evaluation with VARTM infusion. All but one fabric style considered suffered either from poor infusibility or waviness of fibers combined with poor compaction. The exception was a triaxial carbon-fiberglass fabric produced by SAERTEX. This fabric became the primary choice for infused articles throughout the test program. The generally positive results obtained in this program for the SAERTEX material have led to its

  18. Intelligent control of HVAC systems. Part II: perceptron performance analysis

    Directory of Open Access Journals (Sweden)

    Ioan URSU

    2013-09-01

    Full Text Available This is the second part of a paper on intelligent type control of Heating, Ventilating, and Air-Conditioning (HVAC systems. The whole study proposes a unified approach in the design of intelligent control for such systems, to ensure high energy efficiency and air quality improving. In the first part of the study it is considered as benchmark system a single thermal space HVAC system, for which it is assigned a mathematical model of the controlled system and a mathematical model(algorithm of intelligent control synthesis. The conception of the intelligent control is of switching type, between a simple neural network, a perceptron, which aims to decrease (optimize a cost index,and a fuzzy logic component, having supervisory antisaturating role for neuro-control. Based on numerical simulations, this Part II focuses on the analysis of system operation in the presence only ofthe neural control component. Working of the entire neuro-fuzzy system will be reported in a third part of the study.

  19. 29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Tables for Selected Miscellaneous Auxiliary Gear (Mandatory) II Appendix II to Part 1918 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND.... 1918, App. II Appendix II to Part 1918—Tables for Selected Miscellaneous Auxiliary Gear (Mandatory...

  20. Carbon-Phenolic Cages for High-Speed Bearings. Part III - Development of Numerical Models for Heat Generation and Temperature Prediction in Lightly Lubricated Bearings

    National Research Council Canada - National Science Library

    Brown, Jeffrey

    2003-01-01

    .... This portion describes the bearing and thermal analysis models. A process has been developed to numerically investigate operating temperatures of a rolling element bearing which combines capabilities of the Advanced Dynamics of Rolling Elements (ADORE...

  1. A Survey of Optometry Graduates to Determine Practice Patterns: Part II: Licensure and Practice Establishment Experiences.

    Science.gov (United States)

    Bleimann, Robert L.; Smith, Lee W.

    1985-01-01

    A summary of Part II of a two-volume study of optometry graduates conducted by the Association of Schools and Colleges of Optometry is presented. Part II includes the analysis of the graduates' licensure and practice establishment experiences. (MLW)

  2. Integrated smart bearings for next generation aero-engines Part 1: Development of a sensor suite for automatic bearing health monitoring

    OpenAIRE

    Bashir, Imran; Wang, Ling; Harvey, Terence; Zaghari, Bahareh; Weddell, Alexander; White, Neil

    2017-01-01

    The development of smart bearing solutions will contribute to increased aircraft engine reliability, allowing the early detection of bearing failure through robust health monitoring. This project aims to develop intelligent bearing systems for an Ultra High Propulsion Efficiency (UHPE) ground test demonstrator, where a fully integrated self-powered wireless sensing system will be developed for future aircraft. This paper provides a comprehensive review of the state-of-the-art smart bearing te...

  3. Active lubrication applied to radial gas journal bearings. Part 2: Modelling improvement and experimental validation

    DEFF Research Database (Denmark)

    Pierart, Fabián G.; Santos, Ilmar F.

    2016-01-01

    Actively-controlled lubrication techniques are applied to radial gas bearings aiming at enhancing one of their most critical drawbacks, their lack of damping. A model-based control design approach is presented using simple feedback control laws, i.e. proportional controllers. The design approach...... by finite element method and the global model is used as control design tool. Active lubrication allows for significant increase in damping factor of the rotor-bearing system. Very good agreement between theory and experiment is obtained, supporting the multi-physic design tool developed....

  4. Antitumor effect and toxicity of free rhodium (II) citrate and rhodium (II) citrate-loaded maghemite nanoparticles in mice bearing breast cancer.

    Science.gov (United States)

    Carneiro, Marcella Lemos Brettas; Peixoto, Raphael C A; Joanitti, Graziela A; Oliveira, Ricardo G S; Telles, Luis A M; Miranda-Vilela, Ana L; Bocca, Anamélia L; Vianna, Leonora M S; da Silva, Izabel C R; de Souza, Aparecido R; Lacava, Zulmira G M; Báo, Sônia N

    2013-02-16

    Magnetic fluids containing superparamagnetic iron oxide nanoparticles represent an attractive platform as nanocarriers in chemotherapy. Recently, we developed a formulation of maghemite nanoparticles coated with rhodium (II) citrate, which resulted in in vitro cytotoxicity enhanced up to 4.6 times when compared to free rhodium (II) citrate formulation on breast carcinoma cells. In this work, we evaluate the antitumor activity and toxicity induced by these formulations in Balb/c mice bearing orthotopic 4T1 breast carcinoma. Mice were evaluated with regard to the treatments' toxicity through analyses of hemogram, serum levels of alanine aminotransferase, iron, and creatinine; DNA fragmentation and cell cycle of bone marrow cells; and liver, kidney and lung histology. In addition, the antitumor activity of rhodium (II) citrate and maghemite nanoparticles coated with rhodium (II) citrate was verified by tumor volume reduction, histology and immunohistochemistry. Regarding the treatments' toxicity, no experimental groups had alterations in levels of serum ALT or creatinine, and this suggestion was corroborated by the histopathologic examination of liver and kidney of mice. Moreover, DNA fragmentation frequency of bone marrow cells was lower than 15% in all experimental groups. On the other hand, the complexes rhodium (II) citrate-functionalized maghemite and free rhodium (II) citrate led to a marked growth inhibition of tumor and decrease in CD31 and Ki-67 staining. In summary, we demonstrated that both rhodium (II) citrate and maghemite nanoparticles coated with rhodium (II) citrate formulations exhibited antitumor effects against 4T1 metastatic breast cancer cell line following intratumoral administration. This antitumor effect was followed by inhibition of both cell proliferation and microvascularization and by tumor tissue injury characterized as necrosis and fibrosis. Remarkably, this is the first published report demonstrating the therapeutic efficacy of maghemite

  5. 75 FR 41435 - Ball Bearings and Parts Thereof From Germany: Notice of Court Decision Not in Harmony With Final...

    Science.gov (United States)

    2010-07-16

    ...On July 7, 2010, the United States Court of International Trade sustained the Department of Commerce's results of redetermination on remand concerning the final results of the administrative review of the antidumping duty order on ball bearings and parts thereof from Germany. See SKF USA Inc., v. United States, Slip Op. 10-76 (CIT July 7, 2010). The Department is now issuing this notice of court decision not in harmony with the Department of Commerce's determination.

  6. 77 FR 73415 - Ball Bearings and Parts Thereof From France, Germany, and Italy: Final Results of Antidumping...

    Science.gov (United States)

    2012-12-10

    ...On June 5, 2012, the Department of Commerce (the Department) published the preliminary results of the administrative reviews of the antidumping duty orders on ball bearings and parts thereof from France, Germany, and Italy. On October 16, 2012, the Department released its post-preliminary analysis in these reviews. For these final results, we continue to find that sales of the subject merchandise have not been made at prices below normal value.

  7. Nursing as concrete philosophy, Part II: Engaging with reality.

    Science.gov (United States)

    Theodoridis, Kyriakos

    2018-04-01

    This is the second paper of an essay in two parts. The first paper (Part I) is a critical discussion of Mark Risjord's conception of nursing knowledge where I argued against the conception of nursing knowledge as a kind of nursing science. The aim of the present paper (Part II) is to explicate and substantiate the thesis of nursing as a kind of concrete philosophy. My strategy is to elaborate upon certain themes from Wittgenstein's Tractatus in order to canvass a general scheme of philosophy based on a distinction between reality and the world. This distinction will be employed in the appropriation of certain significant features of nursing and nursing knowledge. By elaborating on the contrast between the abstract and the concrete, I will suggest that nursing may be seen as a kind of concrete philosophy, being primarily concerned with reality (and secondarily with the world). This thesis, I will argue, implies that philosophy is the kind of theory that is essential to nursing (which is not so much a theory than a certain kind of activity). © 2017 John Wiley & Sons Ltd.

  8. Bayesian inference for psychology. Part II: Example applications with JASP.

    Science.gov (United States)

    Wagenmakers, Eric-Jan; Love, Jonathon; Marsman, Maarten; Jamil, Tahira; Ly, Alexander; Verhagen, Josine; Selker, Ravi; Gronau, Quentin F; Dropmann, Damian; Boutin, Bruno; Meerhoff, Frans; Knight, Patrick; Raj, Akash; van Kesteren, Erik-Jan; van Doorn, Johnny; Šmíra, Martin; Epskamp, Sacha; Etz, Alexander; Matzke, Dora; de Jong, Tim; van den Bergh, Don; Sarafoglou, Alexandra; Steingroever, Helen; Derks, Koen; Rouder, Jeffrey N; Morey, Richard D

    2018-02-01

    Bayesian hypothesis testing presents an attractive alternative to p value hypothesis testing. Part I of this series outlined several advantages of Bayesian hypothesis testing, including the ability to quantify evidence and the ability to monitor and update this evidence as data come in, without the need to know the intention with which the data were collected. Despite these and other practical advantages, Bayesian hypothesis tests are still reported relatively rarely. An important impediment to the widespread adoption of Bayesian tests is arguably the lack of user-friendly software for the run-of-the-mill statistical problems that confront psychologists for the analysis of almost every experiment: the t-test, ANOVA, correlation, regression, and contingency tables. In Part II of this series we introduce JASP ( http://www.jasp-stats.org ), an open-source, cross-platform, user-friendly graphical software package that allows users to carry out Bayesian hypothesis tests for standard statistical problems. JASP is based in part on the Bayesian analyses implemented in Morey and Rouder's BayesFactor package for R. Armed with JASP, the practical advantages of Bayesian hypothesis testing are only a mouse click away.

  9. II: Through the Western Part of the City: Charlottenburg

    Science.gov (United States)

    Hoffmann, Dieter

    Until 1920 the city we now call Berlin was a collection of independent towns and villages — among them Charlottenburg, which was one of the most important and was the proud sister of Berlin, Prussia’s and Germany’s capital, where the wealthy and innovative bourgeoisie lived. Werner von Siemens, Germany’s pioneer in the modern electrical industry, was a prime example of that elite. His castle-like villa was located not far from today’s Ernst-Reuter-Platz at Otto-Suhr-Allee 10-16, and important parts of his enterprise expanded into the “meadows outside of Charlottenburg” during the second half of the 19th century. It was no accident that the efforts to unite Berlin’s two colleges for trade and construction (both founded around 1800) led to the foundation of a modern Technical College in Charlottenburg in 1879, today’s Technical University of Berlin. Its magnificent main building (figure 1), which was opened in 1882 by the German Emperor, was an expression of the great self-confidence of this new institution of higher learning and of Charlottenburg’s bourgeoisie. Although large parts of the building were destroyed by bombs during World War II, you can still get an impression of its monumentality from what survived at number 135 Strasse des 17. Juni.

  10. Reforming Science Education: Part II. Utilizing Kieran Egan's Educational Metatheory

    Science.gov (United States)

    Schulz, Roland M.

    2009-04-01

    This paper is the second of two parts and continues the conversation which had called for a shift in the conceptual focus of science education towards philosophy of education, with the requirement to develop a discipline-specific “philosophy” of science education. In Part I, conflicting conceptions of science literacy were identified with disparate “visions” tied to competing research programs as well as school-based curricular paradigms. The impasse in the goals of science education and thereto, the contending views of science literacy, were themselves associated with three underlying fundamental aims of education (knowledge-itself; personal development; socialization) which, it was argued, usually undercut the potential of each other. During periods of “crisis-talk” and throughout science educational history these three aims have repeatedly attempted to assert themselves. The inability of science education research to affect long-term change in classrooms was correlated not only to the failure to reach a consensus on the aims (due to competing programs and to the educational ideologies of their social groups), but especially to the failure of developing true educational theories (largely neglected since Hirst). Such theories, especially metatheories, could serve to reinforce science education’s growing sense of academic autonomy and independence from socio-economic demands. In Part II, I offer as a suggestion Egan’s cultural-linguistic theory as a metatheory to help resolve the impasse. I hope to make reformers familiar with his important ideas in general, and more specifically, to show how they can complement HPS rationales and reinforce the work of those researchers who have emphasized the value of narrative in learning science.

  11. Recovery in soccer : part ii-recovery strategies.

    Science.gov (United States)

    Nédélec, Mathieu; McCall, Alan; Carling, Chris; Legall, Franck; Berthoin, Serge; Dupont, Gregory

    2013-01-01

    In the formerly published part I of this two-part review, we examined fatigue after soccer matchplay and recovery kinetics of physical performance, and cognitive, subjective and biological markers. To reduce the magnitude of fatigue and to accelerate the time to fully recover after completion, several recovery strategies are now used in professional soccer teams. During congested fixture schedules, recovery strategies are highly required to alleviate post-match fatigue, and then to regain performance faster and reduce the risk of injury. Fatigue following competition is multifactorial and mainly related to dehydration, glycogen depletion, muscle damage and mental fatigue. Recovery strategies should consequently be targeted against the major causes of fatigue. Strategies reviewed in part II of this article were nutritional intake, cold water immersion, sleeping, active recovery, stretching, compression garments, massage and electrical stimulation. Some strategies such as hydration, diet and sleep are effective in their ability to counteract the fatigue mechanisms. Providing milk drinks to players at the end of competition and a meal containing high-glycaemic index carbohydrate and protein within the hour following the match are effective in replenishing substrate stores and optimizing muscle-damage repair. Sleep is an essential part of recovery management. Sleep disturbance after a match is common and can negatively impact on the recovery process. Cold water immersion is effective during acute periods of match congestion in order to regain performance levels faster and repress the acute inflammatory process. Scientific evidence for other strategies reviewed in their ability to accelerate the return to the initial level of performance is still lacking. These include active recovery, stretching, compression garments, massage and electrical stimulation. While this does not mean that these strategies do not aid the recovery process, the protocols implemented up until

  12. 10 CFR Appendix II to Part 1050 - DOE Form 3735.3-Foreign Travel Statement

    Science.gov (United States)

    2010-01-01

    ... is official agency business. Spouses and dependents may accept such travel and expenses only when... 10 Energy 4 2010-01-01 2010-01-01 false DOE Form 3735.3-Foreign Travel Statement II Appendix II to.... II Appendix II to Part 1050—DOE Form 3735.3—Foreign Travel Statement EC01OC91.041 Statement...

  13. Thinking in nursing education. Part II. A teacher's experience.

    Science.gov (United States)

    Ironside, P M

    1999-01-01

    Across academia, educators are investigating teaching strategies that facilitate students' abilities to think critically. Because may these strategies require low teacher-student ratios or sustained involvement over time, efforts to implement them are often constrained by diminishing resources for education, faculty reductions, and increasing number of part-time teachers and students. In nursing, the challenges of teaching and learning critical thinking are compounded by the demands of providing care to patients with increasingly acute and complex problems in a wide variety of settings. To meet these challenges, nurse teachers have commonly used a variety of strategies to teach critical thinking (1). For instance, they often provide students with case studies or simulated clinical situations in classroom and laboratory settings (2). At other times, students are taught a process of critical thinking and given structured clinical assignments, such as care plans or care maps, where they apply this process in anticipating the care a particular patient will require. Accompanying students onto clinical units, teachers typically evaluate critical thinking ability by reviewing a student's preparation prior to the experience and discussing it with the student during the course of the experience. The rationales students provide for particular nursing interventions are taken as evidence of their critical thinking ability. While this approach is commonly thought to be effective, the evolving health care system has placed increased emphasis on community nursing (3,4), where it is often difficult to prespecify learning experiences or to anticipate patient care needs. In addition, teachers are often not able to accompany each student to the clinical site. Thus, the traditional strategies for teaching and learning critical thinking common to hospital-based clinical courses are being challenged, transformed, and extended (5). Part II of this article describes findings that suggest

  14. All About Dowels - A Review Part II Considerations After Cementation

    Directory of Open Access Journals (Sweden)

    Zishan Dangra

    2017-10-01

    Full Text Available The present review summarizes the published literature examining cementation of the dowel and factors related to it. The peer reviewed English language literature was reviewed from the period 1990 to 2015. Articles were searched in Pubmed/ Medline for the relevant terms. Additional manual searches of some dental journals were also carried out. The original key terms resulted in 228 articles. After applying inclusion criteria, 64 articles remained to be included in part II of this review. Article search indicates that most published literature on dowels are in the form of in vitro analysis. Literature on prefabricated dowel systems far exceeds than the custom cast dowel and newer fibre dowels. Clinical evidence is not sufficient and cannot be used to inform practice confidently. However, within the limitations of this review it is suggested that adhesive fixation is preferred in case of short dowel. Dowel width should be as small as possible. A ferrule of 2 mm has to be provided. Composites have proven to be a good core material provided that adequate tooth structure remained for bonding. Dowel should be inserted if endodontically treated tooth is to be used as abutment for removable partial dentures.

  15. 76 FR 60871 - Ball Bearings and Parts Thereof From France, Germany, and Italy; Termination of Five-Year Reviews

    Science.gov (United States)

    2011-09-30

    ...The subject five-year reviews were initiated in August 2011 to determine whether revocation of the antidumping duty orders on ball bearings and parts thereof from France, Germany, and Italy would be likely to lead to continuation or recurrence of material injury. The Department of Commerce published notice that it was revoking the order effective September 15, 2011, because ``no domestic interested party filed a notice of intent to participate in response to the notice of initiation of the sunset reviews by the applicable deadline.'' (76 FR 57019). Accordingly, pursuant to section 751(c) of the Tariff Act of 1930 (19 U.S.C. 1675(c)), the subject reviews are terminated.

  16. 46 CFR Appendix II to Part 150 - Explanation of Figure 1

    Science.gov (United States)

    2010-10-01

    ... COMPATIBILITY OF CARGOES Pt. 150, App. II Appendix II to Part 150—Explanation of Figure 1 Definition of a..., aromatic hydrocarbons or paraffins. Others will form hazardous combinations with many groups: For example...

  17. RutheniumII Complexes bearing Fused Polycyclic Ligands: From Fundamental Aspects to Potential Applications

    Directory of Open Access Journals (Sweden)

    Ludovic Troian-Gautier

    2014-04-01

    Full Text Available In this review, we first discuss the photophysics reported in the literature for mononuclear ruthenium complexes bearing ligands with extended aromaticity such as dipyrido[3,2-a:2',3'-c]phenazine (DPPZ, tetrapyrido[3,2-a:2',3'-c:3'',2''-h:2''',3'''-j]-phenazine (TPPHZ,  tetrapyrido[3,2-a:2',3'-c:3'',2''-h:2''',3'''-j]acridine (TPAC, 1,10-phenanthrolino[5,6-b]1,4,5,8,9,12-hexaazatriphenylene (PHEHAT 9,11,20,22-tetraaza- tetrapyrido[3,2-a:2',3'-c:3'',2''-l:2''',3'''-n]pentacene (TATPP, etc. Photophysical properties of binuclear and polynuclear complexes based on these extended ligands are then reported. We finally develop the use of binuclear complexes with extended π-systems for applications such as photocatalysis.

  18. 76 FR 22372 - Ball Bearings and Parts Thereof From France, Germany, Italy, Japan, and the United Kingdom...

    Science.gov (United States)

    2011-04-21

    ... preliminarily determined that sales have been made below normal value by certain companies subject to these... a bearing does not influence whether the bearing is covered by one of the orders. The orders cover.... The ultimate application of a bearing also does not influence whether the bearing is covered by the...

  19. Superelastic Ball Bearings: Materials and Design to Avoid Mounting and Dismounting Brinell Damage in an Inaccessible Press-fit Application-. II; Detailed Analysis

    Science.gov (United States)

    Howard, S. Adam; Dellacorte, Christopher

    2015-01-01

    Rolling element bearings utilized in precision rotating machines require proper alignment, preload, and interference fits to ensure overall optimum performance. Hence, careful attention must be given to bearing installation and disassembly procedures to ensure the above conditions are met. Usually, machines are designed in such a way that bearings can be pressed into housings or onto shafts through the races without loading the rolling elements. However, in some instances, either due to limited size or access, a bearing must be installed or removed in such a way that the load path travels through the rolling elements. This can cause high contact stresses between the rolling elements and the races and introduces the potential for Brinell denting of the races. This paper is a companion to the Part I paper by the authors that discusses material selection and the general design philosophy for the bearing. Here, a more in-depth treatment is given to the design of a dent-resistant bearing utilizing a superelastic alloy, 60NiTi, for the races. A common bearing analysis tool based on rigid body dynamics is used in combination with finite element simulations to design the superelastic bearing. The primary design constraints are prevention of denting and avoiding the balls riding over the edge of the race groove during a blind disassembly process where the load passes through the rolling elements. Through an iterative process, the resulting bearing geometry is tailored to improve axial static load capability compared to a deep-groove ball bearing of the same size. The results suggest that careful selection of materials and bearing geometry can enable blind disassembly without damage to the raceways, which is necessary in the current application (a compressor in the International Space Station Environmental Control and Life Support System), and results in potential design flexibility for other applications, especially small machines with miniature bearings.

  20. Psychiatric emergencies (part II): psychiatric disorders coexisting with organic diseases.

    Science.gov (United States)

    Testa, A; Giannuzzi, R; Sollazzo, F; Petrongolo, L; Bernardini, L; Dain, S

    2013-02-01

    In this Part II psychiatric disorders coexisting with organic diseases are discussed. "Comorbidity phenomenon" defines the not univocal interrelation between medical illnesses and psychiatric disorders, each other negatively influencing morbidity and mortality. Most severe psychiatric disorders, such as schizophrenia, bipolar disorder and depression, show increased prevalence of cardiovascular disease, related to poverty, use of psychotropic medication, and higher rate of preventable risk factors such as smoking, addiction, poor diet and lack of exercise. Moreover, psychiatric and organic disorders can develop together in different conditions of toxic substance and prescription drug use or abuse, especially in the emergency setting population. Different combinations with mutual interaction of psychiatric disorders and substance use disorders are defined by the so called "dual diagnosis". The hypotheses that attempt to explain the psychiatric disorders and substance abuse relationship are examined: (1) common risk factors; (2) psychiatric disorders precipitated by substance use; (3) psychiatric disorders precipitating substance use (self-medication hypothesis); and (4) synergistic interaction. Diagnostic and therapeutic difficulty concerning the problem of dual diagnosis, and legal implications, are also discussed. Substance induced psychiatric and organic symptoms can occur both in the intoxication and withdrawal state. Since ancient history, humans selected indigene psychotropic plants for recreational, medicinal, doping or spiritual purpose. After the isolation of active principles or their chemical synthesis, higher blood concentrations reached predispose to substance use, abuse and dependence. Abuse substances have specific molecular targets and very different acute mechanisms of action, mainly involving dopaminergic and serotoninergic systems, but finally converging on the brain's reward pathways, increasing dopamine in nucleus accumbens. The most common

  1. Polymerization of Methyl Methacrylate Catalyzed by Co(II), Cu(II), and Zn(II) Complexes Bearing N-Methyl-N-((pyridin-2-yl)methyl) cyclohexanamine

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Seoung Hyun; Lee, Hyosun [Kyungpook National University, Daegu (Korea, Republic of); Shin, Jongwon [POSTECH, Pohang (Korea, Republic of); Nayab, Saira [Shaheed Benazir Bhutto University, Sheringal (Pakistan)

    2016-05-15

    We demonstrated the synthesis and characterization of Co(II), Cu(II), and Zn(II) complexes ligated to N-methyl-N-((pyridin-2-yl)methyl)cyclohexanamine. The complex [Co(nmpc)Cl{sub 2}] in the presence of MMAO showed the highest catalytic activity for MMA polymerization at 60 °C compared with its Zn(II) and Cu(II) analogs. The metal center showed an obvious influence on the catalytic activity, although this appeared to have no effect on the stereo-regularity of the resultant PMMA. X-ray diffraction analysis revealed that [Co(nmpc)Cl{sub 2}] and [Zn(nmpc)Cl{sub 2}] crystallized in the monoclinic system with space group P2{sub 1}/c and existed as monomeric and solvent-free complexes.

  2. 40 CFR Appendix II to Part 1042 - Steady-State Duty Cycles

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Steady-State Duty Cycles II Appendix..., App. II Appendix II to Part 1042—Steady-State Duty Cycles (a) The following duty cycles apply as specified in § 1042.505(b)(1): (1) The following duty cycle applies for discrete-mode testing: E3 mode No...

  3. 40 CFR Appendix II to Part 1054 - Duty Cycles for Laboratory Testing

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Duty Cycles for Laboratory Testing II.... 1054, App. II Appendix II to Part 1054—Duty Cycles for Laboratory Testing (a) Test handheld engines with the following steady-state duty cycle: G3 mode No. Engine speed a Torque(percent) b Weighting...

  4. 40 CFR Appendix II to Part 600 - Sample Fuel Economy Calculations

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample Fuel Economy Calculations II... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. II Appendix II to Part 600—Sample Fuel Economy Calculations (a) This sample fuel economy calculation is applicable to...

  5. Population-based contracting (population health): part II.

    Science.gov (United States)

    Jacofsky, D J

    2017-11-01

    Modern healthcare contracting is shifting the responsibility for improving quality, enhancing community health and controlling the total cost of care for patient populations from payers to providers. Population-based contracting involves capitated risk taken across an entire population, such that any included services within the contract are paid for by the risk-bearing entity throughout the term of the agreement. Under such contracts, a risk-bearing entity, which may be a provider group, a hospital or another payer, administers the contract and assumes risk for contractually defined services. These contracts can be structured in various ways, from professional fee capitation to full global per member per month diagnosis-based risk. The entity contracting with the payer must have downstream network contracts to provide the care and facilities that it has agreed to provide. Population health is a very powerful model to reduce waste and costs. It requires a deep understanding of the nuances of such contracting and the appropriate infrastructure to manage both networks and risk. Cite this article: Bone Joint J 2017;99-B:1431-4. ©2017 The British Editorial Society of Bone & Joint Surgery.

  6. Antitumor effect of free rhodium (II) citrate and rhodium (II) citrate-loaded maghemite nanoparticles on mice bearing breast cancer: a systemic toxicity assay.

    Science.gov (United States)

    Peixoto, Raphael Cândido Apolinário; Miranda-Vilela, Ana Luisa; de Souza Filho, José; Carneiro, Marcella Lemos' Brettas; Oliveira, Ricardo G S; da Silva, Matheus Oliveira; de Souza, Aparecido R; Báo, Sônia Nair

    2015-05-01

    Breast cancer is one of the most prevalent cancer types among women. The use of magnetic fluids for specific delivery of drugs represents an attractive platform for chemotherapy. In our previous studies, it was demonstrated that maghemite nanoparticles coated with rhodium (II) citrate (Magh-Rh2Cit) induced in vitro cytotoxicity and in vivo antitumor activity, followed by intratumoral administration in breast carcinoma cells. In this study, our aim was to follow intravenous treatment to evaluate the systemic antitumor activity and toxicity induced by these formulations in Balb/c mice bearing orthotopic 4T1 breast carcinoma. Female Balb/c mice were evaluated with regard to toxicity of intravenous treatments through analyses of hemogram, serum levels of alanine aminotransferase, iron, and creatinine and liver, kidney, and lung histology. The antitumor activity of rhodium (II) citrate (Rh2Cit), Magh-Rh2Cit, and maghemite nanoparticles coated with citrate (Magh-Cit), used as control, was evaluated by tumor volume reduction, histology, and morphometric analysis. Magh-Rh2Cit and Magh-Cit promoted a significant decrease in tumor area, and no experimental groups presented hematotoxic effects or increased levels of serum ALT and creatinine. This observation was corroborated by the histopathological examination of the liver and kidney of mice. Furthermore, the presence of nanoparticles was verified in lung tissue with no morphological changes, supporting the idea that our nanoformulations did not induce toxicity effects. No studies about the systemic action of rhodium (II) citrate-loaded maghemite nanoparticles have been carried out, making this report a suitable starting point for exploring the therapeutic potential of these compounds in treating breast cancer.

  7. 75 FR 53661 - Ball Bearings and Parts Thereof From France, Germany, Italy, Japan, and the United Kingdom: Final...

    Science.gov (United States)

    2010-09-01

    ... orders remain dispositive. The size or precision grade of a bearing does not influence whether the... also does not influence whether the bearing is covered by the orders. Bearings designed for highly... for individual examination of their sales of the subject merchandise to the United States during the...

  8. Complexometric determination, Part II: Complexometric determination of Cu2+-ions

    Directory of Open Access Journals (Sweden)

    Rajković Miloš B.

    2002-01-01

    Full Text Available A copper-selective electrode of the coated wire type based on sulphidized copper wire was applied successfully for determining Cu(II ions by complexometric titration with the disodium salt of EDTA (complexon III. By the formation of internal complex compounds with the Cu(II ion, the copper concentration in the solution decreases, and all this is followed by a change of potential of the indicator system Cu-DWISE (or Cu-EDWISE/SCE. At the terminal point of titration, when all the Cu(II ions are already utilized for the formation of the complex with EDTA, there occurs a steep rise of potential, thus enabling us, through the first or second derivative to note the quantity of copper that is present in the solution. Copper-selective electrode showed a responsivity towards titration with EDTA as a complexing agent, with the absence of "fatigue" due to a great number of repeated measurings. Errors occurring during quantitative measurements were more a characteristic of the overall procedure which involve, because of the impossibility of the complete absence of subjectivity, a constant error, and the reproducibility of the results confirmed this fact. The disodium salt of EDTA appeared as a very efficient titrant in all titrations and with various concentrations ot Cu(II ions in the solution, with somewhat weaker response at lower concentrations in the solution.

  9. A Conversation with William A. Fowler Part II

    Science.gov (United States)

    Greenberg, John

    2005-06-01

    Physicist William A.Fowler initiated an experimental program in nuclear astrophysics after World War II. He recalls here the Steady State versus Big Bang controversy and his celebrated collaboration with Fred Hoyle and Geoffrey and Margaret Burbidge on nucleosynthesis in stars. He also comments on the shift away from nuclear physics in universities to large accelerators and national laboratories.

  10. Inteligencia Artificial y Neurología: II Parte

    Directory of Open Access Journals (Sweden)

    Mario Camacho Pinto

    1986-12-01

    Full Text Available

    Algunos comentarios sobre la primera parte me han inducido a ampliar las bases de este trabajo mediante la presentación de aspectos comunes y conceptos disímiles sobre la hipotética relación entre inteligencia artificial (lA e inteligencia humana(IH. El tema es tan complejo que un intento por resumirlo de por sí ya es atrayente además de necesario.

    Microhistoria de la lA. Ciñéndome a una cruda realidad la lA nació en la Conferencia de Darmouth, año 1956, cuando John McCarthy, profesor de ciencia de computador en Stanford Un. acuñó el término de lA. Sin embargo, especulando un poco podemos decir que cierta inquietud existió desde la antigüedad, mucho antes de los computadores y aún de la electrónica (1 cuando el ser humano irresistiblemente mostraba inquietud por crear I fuera del cerebro humano. Se encuentran algunos ejemplos en la Mitología griega: Hefestos. dios del fuego y de los metales, confeccionaba creaciones semihumanas en su forja. Pigmalión desencantado de las mujeres modeló su propia ninfa en mármol y para poder casarse con ella imploró suplicante hasta conseguir que Afrodita le diera vida.

    En la Europa medioeval al papa Silvestre II (apodado el hechicero por su sabiduría, año 909 D.C. se le atribuye que construía cabezas parlantes. En el siglo XVI Para celso clamó haber inventado un homúnculo. Y el rabino checo Jundo ben Loew esculpió un hombre en arcilla, José Golem, y lo constituyó espía en Praga. En 1854 el matemático británico George Boole propuso un sistema para describir lógica (2 -las leyes del pensamiento en términos matemáticos: “álgebra booliana”, “mathematical logics” que representa procesos lógicos con dos dígitos, 9 y 1.

    En 1937 Alan Turing demostró que una máquina binaria podía ser programada para realizar cualquier tarea algorítmica. Esta máquina de Turing sólo podía ejecutar dos acciones: dibujar y borrar. En el mismo año Claude

  11. The Search for Another Earth–Part II

    Indian Academy of Sciences (India)

    Permanent link: https://www.ias.ac.in/article/fulltext/reso/021/10/0899-0910. Keywords. Exoplanets, earth, super-earth, diamond planet, neptune, habitability, extra-terrestrial life. Abstract. In the first part, we discussed the various methods for thedetection of planets outside the solar system known as theexoplanets. In this part ...

  12. Cardiac nuclear medicine, part II: diagnosis of coronary artery diseas

    International Nuclear Information System (INIS)

    Polak, J.F.; Holman, B.L.

    1981-01-01

    Diagnosing coronary artery disease is difficult and requires careful consideration of the roles and limitations of the tests used. Standard ECG tests are not reliable indicators of the presence of disease in asymptomatic patients. Thallium stress testing to assess ischemia and exercise ventriculography to assess functional status of the heart are limited in sensitivity and specificity. This is the second of a three-part series on cardiac nuclear medicine. Part I (Med. Instrum., May-June, 1981) focused on the commonly used examinations in cardiac physiology and pathophysiology. Part III will focus on myocardial infarction and other cardiac diseases

  13. 30 CFR Appendix II to Subpart D of... - Appendix II to Subpart D of Part 18

    Science.gov (United States)

    2010-07-01

    ... LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Machines Assembled With Certified or Explosion-Proof Components, Field Modifications of Approved Machines, and Permits To Use Experimental Equipment Pt. 18, Subpt. D, App. II Appendix II to Subpart D of...

  14. Guidelines for acute ischemic stroke treatment: part II: stroke treatment

    Directory of Open Access Journals (Sweden)

    Sheila Cristina Ouriques Martins

    2012-11-01

    Full Text Available The second part of these Guidelines covers the topics of antiplatelet, anticoagulant, and statin therapy in acute ischemic stroke, reperfusion therapy, and classification of Stroke Centers. Information on the classes and levels of evidence used in this guideline is provided in Part I. A translated version of the Guidelines is available from the Brazilian Stroke Society website (www.sbdcv.com.br.

  15. EL español andino. II parte

    Directory of Open Access Journals (Sweden)

    Rubén Arboleda Toro

    2002-01-01

    Full Text Available En el número 13 de esta revista (nov. del 2000 se publicó una primera parte del estudio sobre el español andino. Presentamos ahora una segunda parte que comprende aspectos histórico-geográficos de Nariño y Putumayo andinos, región de Colombia donde se habla esa variedad, y una descripción general de su realidad lingüística. Esperamos que sean objeto de otra publicación la descripción de los rasgos dialectales del español andino, parte nuclear del trabajo, y la presentación de la metodología y el corpus. En esto nos encontramos trabajando. Incluimos no obstante un inventario de rasgos más amplio que el presentado en la primera parte. Pero por ahora se trata de eso, de un inventario ilustrativo, no del análisis en el que estamos empeñados, en el marco del contacto de lenguas, el cambio lingüístico y la relación entre la norma y las posibilidades del sistema. Para contextualizar esta segunda parte, incluimos, a manera de introducción, un resumen de la primera.

  16. Ultra-violet radiation: hazard in workplaces? (part II)

    International Nuclear Information System (INIS)

    Mohd Yusof Mohd Ali

    2003-01-01

    Not many workers are aware that apart from chemicals, physical agents, noise and machines which are known to be hazardous in workplaces, there exist another source of hazard which is equally important to be recognised and respected, that is hazard due to ultrviolet radiation (UV). This is the continuation of part I, which was discussed in the later issue. In this part, hazard of ultraviolet radiation were briefly discused i.e. effects on the skin and the eyes. Other subjects discussed are exposure limits, how to assess the radiation, protection against ultraviolet radiation

  17. Programming Models for Three-Dimensional Hydrodynamics on the CM-5 (Part II)

    International Nuclear Information System (INIS)

    Amala, P.A.K.; Rodrigue, G.H.

    1994-01-01

    This is a two-part presentation of a timing study on the Thinking Machines CORP. CM-5 computer. Part II is given in this study and represents domain-decomposition and message-passing models. Part I described computational problems using a SIMD model and connection machine FORTRAN (CMF)

  18. [Low grade renal trauma (Part II): diagnostic validity of ultrasonography].

    Science.gov (United States)

    Grill, R; Báca, V; Otcenásek, M; Zátura, F

    2010-04-01

    The aim of the study was to verify whether ultrasonography can be considered a reliable method for the diagnosis of low-grade renal trauma. The group investigated included patients with grade I or grade II blunt renal trauma, as classified by the AAST grading system, in whom ultrasonography alone or in conjunction with computed tomography was used as a primary diagnostic method. B-mode ultrasound with a transabdominal probe working at frequencies of 2.5 to 5.0 MHz was used. Every finding of post-traumatic changes in the renal tissues, i.e., post-contusion hypotonic infiltration of the renal parenchyma or subcapsular haematoma, was included. The results were statistically evaluated by the Chi-square test with the level of significance set at 5%, using Epi Info Version 6 CZ software. The group comprised 112 patients (43 women, 69 men) aged between 17 and 82 years (average, 38 years). It was possible to diagnose grade I or grade II renal injury by ultrasonography in only 60 (54%) of them. The statistical significance of ultrasonography as the only imaging method for the diagnosis of low-grade renal injury was not confirmed (p=0.543) Low-grade renal trauma is a problem from the diagnostic point of view. It usually does not require revision surgery and, if found during repeat surgery for more serious injury of another organ, it usually does not receive attention. Therefore, the macroscopic presentation of grade I and grade II renal injury is poorly understood, nor are their microscopic findings known, because during revision surgery these the traumatised kidneys are not usually removed and their injuries at autopsy on the patients who died of multiple trauma are not recorded either. The results of this study demonstrated that the validity of ultrasonography for the diagnosis of low-grade renal injury is not significant, because this examination can reveal only some of the renal injuries such as perirenal haematoma. An injury to the renal parenchyma is also indicated by

  19. Aesthetic Pursuits: Windows, Frames, Words, Images--Part II

    Science.gov (United States)

    Burke, Ken

    2005-01-01

    In Part I of this study (Burke, 2005), the author presented the essentials of Image Presentation Theory--IPT--and its application to the analytical explication of various spatial designs in and psychological responses to images, from the illusions of depth in what is referred to as "windows" in cinema theory to the more patterned abstractions of…

  20. Topics in Finance: Part II--Financial Analysis

    Science.gov (United States)

    Laux, Judy

    2010-01-01

    The second article in a series designed to supplement the introductory financial management course, this essay addresses financial statement analysis, including its impact on stock valuation, disclosure, and managerial behavior. [For "Topics in Finance Part I--Introduction and Stockholder Wealth Maximization," see EJ1060345.

  1. Small Business Management. Part II. A Suggested Adult Course Outline.

    Science.gov (United States)

    New York State Education Dept., Albany. Bureau of Continuing Education Curriculum Development.

    This teacher's guide is a companion to "Small Business Management Part I" published by the New York State Education Department in 1968. The course outlined by the guide is primarily for those who aspire to own and operate their own business, and those in business who wish to improve their operations. The course consists of six lessons covering…

  2. On Railroad Tank Car Puncture Performance: Part II - Estimating Metrics

    Science.gov (United States)

    2016-04-12

    This paper is the second in a two-part series on the puncture performance of railroad tank cars carrying hazardous materials in the event of an accident. Various metrics are often mentioned in the open literature to characterize the structural perfor...

  3. The Search for Another Earth – Part II

    Indian Academy of Sciences (India)

    In this part, we will describe various kinds of ... the Earth will also be discussed. 1. .... life. system is oxygen rich because the interstellar cloud from which the Sun and the solar planets were born .... a habitable planet must be rocky in order to sustain liquid ... helped in keeping the atmosphere of the Earth habitable for a long.

  4. Solar Energy Education. Reader, Part II. Sun story. [Includes glossary

    Energy Technology Data Exchange (ETDEWEB)

    1981-05-01

    Magazine articles which focus on the subject of solar energy are presented. The booklet prepared is the second of a four part series of the Solar Energy Reader. Excerpts from the magazines include the history of solar energy, mythology and tales, and selected poetry on the sun. A glossary of energy related terms is included. (BCS)

  5. Lagrangian intersection Floer theory anomaly and obstruction, part II

    CERN Document Server

    Fukaya, Kenji; Ohta, Hiroshi; Ono, Kaoru

    2009-01-01

    This is a two-volume series research monograph on the general Lagrangian Floer theory and on the accompanying homological algebra of filtered A_\\infty-algebras. This book provides the most important step towards a rigorous foundation of the Fukaya category in general context. In Volume I, general deformation theory of the Floer cohomology is developed in both algebraic and geometric contexts. An essentially self-contained homotopy theory of filtered A_\\infty algebras and A_\\infty bimodules and applications of their obstruction-deformation theory to the Lagrangian Floer theory are presented. Volume II contains detailed studies of two of the main points of the foundation of the theory: transversality and orientation. The study of transversality is based on the virtual fundamental chain techniques (the theory of Kuranishi structures and their multisections) and chain level intersection theories. A detailed analysis comparing the orientations of the moduli spaces and their fiber products is carried out. A self-co...

  6. Part I. Mechanisms of injury associated with extracorporeal shock wave lithotripsy; Part II. Exsolution of volatiles

    Science.gov (United States)

    Howard, Danny Dwayne

    Part I - Shock waves are focused in extracorporeal shock wave lithotripsy (ESWL) machines to strengths sufficient to fracture kidney stones. Substantial side effects-most of them acute-have resulted from this procedure, including injury to soft tissue. The focusing of shock waves through various layers of tissue is a complex process which stimulates many bio-mechano-chemical responses.This thesis presents results of an in vitro study of the initial mechanical stimulus. Planar nitrocellulose membranes of order 10 um thick were used as models of thin tissue structures. Two modes of failure were recorded: Failure due to cavitation collapsing on or near the membranes, and failure induced by altering the structure of shock waves. Tests were done in water at and around F2 to characterize the extent of cavitation damage, and was found to be confined within the focal region, 1.2 cm along the axis of focus.Scattering media were used to simulate the effects of acoustic nonuniformity of tissue and to alter the structure of focusing shock waves. 40 um diameter (average) hollow glass spheres were added to ethylene glycol, glycerine and castor oil to vary the properties of the scattering media. Multiple layer samples of various types of phantom tissue were tested in degassed castor oil to gauge the validity of the scattering media. The scattering media and tissue samples increased the rise time decreased strain rate in a similar fashion. Membranes were damaged by the decreased strain rate and accumulated effects of the altered structure: After about 20 or so shocks immersed in the scattering media and after about 100 shocks behind the tissue samples. The mode of failure was tearing with multiple tears in some cases from about .1 cm to about 3 cm depending of the number of shocks and membrane thickness.Part II - This work examines the exsolution of volatiles-carbon dioxide from water-in a cylindrical test cell under different pressure conditions. Water was supersaturated with

  7. DEPRESSION, ANXIETY AND MYOCARDIAL INFARCTION: EVERYTHING JUST BEGINS. PART II

    Directory of Open Access Journals (Sweden)

    Y. A. Vasyuk

    2015-12-01

    Full Text Available A review is devoted to a comorbidity of myocardial infarction and anxious and depressive disorders. In the first part (Rational Pharmacother. Cardiol. 2007;3:41-51 data concerning prevalence of depression in myocardial infarction, pathophysiological mechanisms connecting depression and ischemic heart disease (IHD were given. Influence of concomitant depressive disorders on clinical state and forecast of patients after myocardial infarction was discussed. The second part of the review is devoted to the anxious disorders in myocardial infarction as well as to influence of anxious and depressive disorders on life quality of patients with myocardial infarction. Besides, contemporary approaches to the therapy of anxious and depressive disorders in patients with IHD are discussed.

  8. GSTARS computer models and their applications, Part II: Applications

    Science.gov (United States)

    Simoes, F.J.M.; Yang, C.T.

    2008-01-01

    In part 1 of this two-paper series, a brief summary of the basic concepts and theories used in developing the Generalized Stream Tube model for Alluvial River Simulation (GSTARS) computer models was presented. Part 2 provides examples that illustrate some of the capabilities of the GSTARS models and how they can be applied to solve a wide range of river and reservoir sedimentation problems. Laboratory and field case studies are used and the examples show representative applications of the earlier and of the more recent versions of GSTARS. Some of the more recent capabilities implemented in GSTARS3, one of the latest versions of the series, are also discussed here with more detail. ?? 2008 International Research and Training Centre on Erosion and Sedimentation and the World Association for Sedimentation and Erosion Research.

  9. Operation of industrial electrical substations. Part II: practical applications

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez Jimenez, Juan J; Zerquera Izquierdo, Mariano D; Beltran Leon, Jose S; Garcia Martinez, Juan M; Alvarez Urena, Maria V; Meza Diaz, Guillermo [Universidad de Guadalajara (Mexico)]. E-mails: cheosj@yahoo.com; mdzi@hotmail.com; beltran5601@yahoo.com.mx; jmargarmtz@yahoo.com; victory_alvarez@telmexmail.com; depmec@cucei.udg.mx

    2013-03-15

    The practical application of the methodology explained in Part 1 in a Cuban industry is the principal objective of this paper. The calculus of the economical operation of the principal transformers of the industrial plant is shown of the one very easy form, as well as the determination of the equations of the losses when the transformers operate under a given load diagram. It is calculated the state load which will be passed to the operation in parallel. [Spanish] El objetivo principal de este trabajo es la aplicacion practica de la metodologia, en una industria cubana, que se explico en la Parte 1. El calculo de la operacion economica de los principales transformadores de la planta industrial se muestra de una forma muy facil, asi como la determinacion de las ecuaciones de las perdidas cuando los transformadores operan bajo un diagrama de carga dado. Se calcula la carga de estado que se pasa a la operacion en paralelo.

  10. The equivalence myth of quantum mechanics-part II

    Science.gov (United States)

    Muller, F. A.

    The author endeavours to show two things: first, that Schrödingers (and Eckarts) demonstration in March (September) 1926 of the equivalence of matrix mechanics, as created by Heisenberg, Born, Jordan and Dirac in 1925, and wave mechanics, as created by Schrödinger in 1926, is not foolproof; and second, that it could not have been foolproof, because at the time matrix mechanics and wave mechanics were neither mathematically nor empirically equivalent. That they were is the Equivalence Myth. In order to make the theories equivalent and to prove this, one has to leave the historical scene of 1926 and wait until 1932, when von Neumann finished his magisterial edifice. During the period 1926-1932 the original families of mathematical structures of matrix mechanics and of wave mechanics were stretched, parts were chopped off and novel structures were added. To Procrustean places we go, where we can demonstrate the mathematical, empirical and ontological equivalence of 'the final versions of' matrix mechanics and wave mechanics. The present paper claims to be a comprehensive analysis of one of the pivotal papers in the history of quantum mechanics: Schrödingers equivalence paper. Since the analysis is performed from the perspective of Suppes structural view ('semantic view') of physical theories, the present paper can be regarded not only as a morsel of the internal history of quantum mechanics, but also as a morsel of applied philosophy of science. The paper is self-contained and presupposes only basic knowledge of quantum mechanics. For reasons of length, the paper is published in two parts; Part I appeared in the previous issue of this journal. Section 1 contains, besides an introduction, also the papers five claims and a preview of the arguments supporting these claims; so Part I, Section 1 may serve as a summary of the paper for those readers who are not interested in the detailed arguments.

  11. Comparison of microstickies measurement methods. Part II, Results and discussion

    Science.gov (United States)

    Mahendra R. Doshi; Angeles Blanco; Carlos Negro; Concepcion Monte; Gilles M. Dorris; Carlos C. Castro; Axel Hamann; R. Daniel Haynes; Carl Houtman; Karen Scallon; Hans-Joachim Putz; Hans Johansson; R. A. Venditti; K. Copeland; H.-M. Chang

    2003-01-01

    In part I of the article we discussed sample preparation procedure and described various methods used for the measurement of microstickies. Some of the important features of different methods are highlighted in Table 1. Temperatures used in the measurement methods vary from room temperature in some cases, 45 °C to 65 °C in other cases. Sample size ranges from as low as...

  12. Slag Behavior in Gasifiers. Part II: Constitutive Modeling of Slag

    Energy Technology Data Exchange (ETDEWEB)

    Massoudi, Mehrdad [National Energy Technology Laboratory; Wang, Ping

    2013-02-07

    The viscosity of slag and the thermal conductivity of ash deposits are among two of the most important constitutive parameters that need to be studied. The accurate formulation or representations of the (transport) properties of coal present a special challenge of modeling efforts in computational fluid dynamics applications. Studies have indicated that slag viscosity must be within a certain range of temperatures for tapping and the membrane wall to be accessible, for example, between 1,300 °C and 1,500 °C, the viscosity is approximately 25 Pa·s. As the operating temperature decreases, the slag cools and solid crystals begin to form. Since slag behaves as a non-linear fluid, we discuss the constitutive modeling of slag and the important parameters that must be studied. We propose a new constitutive model, where the stress tensor not only has a yield stress part, but it also has a viscous part with a shear rate dependency of the viscosity, along with temperature and concentration dependency, while allowing for the possibility of the normal stress effects. In Part I, we reviewed, identify and discuss the key coal ash properties and the operating conditions impacting slag behavior.

  13. 12 CFR Appendix II to Part 27 - Information for Government Monitoring Purposes

    Science.gov (United States)

    2010-01-01

    ... II Appendix II to Part 27 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY... Monitoring Purposes The following language is approved by the Comptroller of the Currency and will satisfy... used separately. This information may also be provided orally by the applicant. The following...

  14. 31 CFR Appendix II to Part 13 - Form of Bill for Reimbursement

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Form of Bill for Reimbursement II Appendix II to Part 13 Money and Finance: Treasury Office of the Secretary of the Treasury PROCEDURES FOR... title) of ______ (Country) to participate in the work of ______ (International Organization) or...

  15. 40 CFR Appendix II to Part 1045 - Duty Cycles for Propulsion Marine Engines

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Duty Cycles for Propulsion Marine... Pt. 1045, App. II Appendix II to Part 1045—Duty Cycles for Propulsion Marine Engines (a) The following duty cycle applies for discrete-mode testing: E4 Mode No. Enginespeed 1 Torque(percent) 2...

  16. 40 CFR Appendix II to Part 1039 - Steady-State Duty Cycles

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Steady-State Duty Cycles II Appendix... Appendix II to Part 1039—Steady-State Duty Cycles (a) The following duty cycles apply for constant-speed engines: (1) The following duty cycle applies for discrete-mode testing: D2 mode number Engine speed...

  17. Marketing in the E-Business World, Parts I & II | Smith | LBS ...

    African Journals Online (AJOL)

    Marketing in the E-Business World, Parts I & II. ... Open Access DOWNLOAD FULL TEXT ... of many of Americas largest companies gather at the Waldorf Astoria Hotel in New York City for the Conference Boards Annual Marketing Conference.

  18. The year 2012 in the European Heart Journal-Cardiovascular Imaging. Part II.

    Science.gov (United States)

    Plein, Sven; Knuuti, Juhani; Edvardsen, Thor; Saraste, Antti; Piérard, Luc A; Maurer, Gerald; Lancellotti, Patrizio

    2013-07-01

    The part II of the best of the European Heart Journal - Cardiovascular Imaging in 2012 specifically focuses on studies of valvular heart diseases, heart failure, cardiomyopathies, and congenital heart diseases.

  19. Unknown facets of Well-Known Scientists Series - Part II

    Directory of Open Access Journals (Sweden)

    V S Dixit

    2016-01-01

    Full Text Available 1st in the series of articles on “Unknown Facets of well-known Scientists” was about Sir Frederick Grant Banting, co-discoverer of Insulin, who also researched in Aviation and Diving Medicines, results of which brought extraordinary benefits for Flight crew during the World War II. The article was published in the previous issue of the Journal Unknown facets could be celebrated attributes, talents or otherwise, but it is necessary that we get to know fully about the “great mind". THIS ARTICLE IS ABOUT DR WERNER THEODOR OTTO FORSSMANN, A CARDIOLOGIST, WHO BECAME A UROLOGIST! Does the name Dr Forssmann ring a bell? He shared the 1956 Nobel Prize in Physiology or Medicine with “Andre Cournand and Dickinson Richards". The trio was awarded for their “discoveries concerning heart catheterization and pathological changes in the circulatory system". Dr Forssmann was nominated for performing an experiment in which he introduced a catheter into a vein of his arm, further passing it onward into his heart It was risky. This was in the year 1929. Subject of this article is the self-experimentation he carried out and what happened later.

  20. Historia de la Conservación Preventiva. Parte II

    OpenAIRE

    García Fernández, Isabel M.

    2014-01-01

    La segunda parte de la historia de la conservación preventiva comienza en 1990; esta etapa es mucho más corta que la primera,pero más prolífica en materiales, proyectos y publicaciones. Vamos a ver cómo desde sus inicios, la conservación preventiva ha ido cobrando protagonismo en todos los ámbitos relacionados con la preservación y uso del patrimonio. En este artículo vamos a destacar los hitos fundamentales que han conseguido afianzar esta disciplina en los últimos 25 años y valorar- su desa...

  1. Designing carbon markets, Part II: Carbon markets in space

    International Nuclear Information System (INIS)

    Fankhauser, Samuel; Hepburn, Cameron

    2010-01-01

    This paper analyses the design of carbon markets in space (i.e., geographically). It is part of a twin set of papers that, starting from first principles, ask what an optimal global carbon market would look like by around 2030. Our focus is on firm-level cap-and-trade systems, although much of what we say would also apply to government-level trading and carbon offset schemes. We examine the 'first principles' of spatial design to maximise flexibility and to minimise costs, including key design issues in linking national and regional carbon markets together to create a global carbon market.

  2. Heavy lon Reactions The Elementary Processes, Parts I and II

    CERN Document Server

    Broglia, Ricardo A

    2004-01-01

    Combining elastic and inelastic processes with transfer reactions, this two-part volume explores how these events affect heavy ion collisions. Special attention is given to processes involving the transfer of two nucleons, which are specific for probing pairing correlations in nuclei. This novel treatment provides, together with the description of surface vibration and rotations, a unified picture of heavy ion reactions in terms of the elementary modes of nuclear excitation. Heavy Ion Reactions is essential reading for beginning graduate students as well as experienced researchers.

  3. Processes on Uncontrolled Aerodromes and Safety Indicators - Part II

    Directory of Open Access Journals (Sweden)

    Vladimír Plos

    2014-01-01

    Full Text Available This article follows on the Part I, where the basic processes on uncontrolled aerodromes were introduced. The uncontrolled aerodromes face with the growing traffic and from that result the higher workload on AFIS officer. This means a higher potential for dangerous situations.The article describes some models of sub-processes and creates several safety indicators related to the operation at uncontrolled aerodromes. Thanks to monitoring and evaluation of safety indicators can be adopted targeted safety measures and thus increase safety on small uncontrolled aerodromes.

  4. Prevention of Dealloying in Manganese Aluminium Bronze Propeller: Part II

    Directory of Open Access Journals (Sweden)

    Napachat Tareelap

    2014-03-01

    Full Text Available Due to the failure of manganese aluminium bronze (MAB propeller caused by dealloying corrosion as described in Part I [1], this work aims to study the prevention of dealloying corrosion using aluminium and zinc sacrificial anodes. The results indicated that both of the sacrificial anodes could prevent the propeller from dealloying. Moreover, the dealloying in seawater was less than that found in brackish water. It was possible that hydroxide ions, from cathodic reaction, reacted with calcium in seawater to form calcium carbonate film protecting the propeller from corrosion.

  5. Centric relation: concepts revision and recording techniques. Part II

    OpenAIRE

    Orozco Varo, Ana; Arroyo Cruz, Gema; Martinez De Fuentes, Rafael; Ventura de la Torre, Javier; Cañadas Rodríguez, Diego; Jiménez-Castellanos Ballesteros, Emilio

    2008-01-01

    La relación céntrica ha sido objeto de disparidad de criterios en la odontología durante más de un siglo. A lo largo de este trabajo, vamos a exponer diferentes métodos usados tanto para obtener el registro, como para comprobar su certeza y corroborar la posición condilar. Dado que no existe evidencia científica en el tema, en este trabajo, revisaremos los estudios experimentales que aparecen en la literatura. Los hemos divididos en dos partes, la primera relacionada con la definición de rela...

  6. 78 FR 40692 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Science.gov (United States)

    2013-07-08

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-570-601] Tapered Roller Bearings and..., International Trade Administration, Department of Commerce. SUMMARY: The Department of Commerce (Department) is... Department selected one mandatory respondent for individual examination (i.e., Changshan Peer Bearing Co. Ltd...

  7. The year's new drugs & biologics 2014 - Part II: trends & challenges.

    Science.gov (United States)

    Graul, A I; Serebrov, M; Cruces, E; Tracy, M; Dulsat, C

    2015-02-01

    2014 was a year of continued high activity in the pharma and biotech industry, as evidenced in part I of this annual two-part review article published last month in this journal (1). As of December 23, 2014, a total of 55 new chemical and biological entities had reached their first markets worldwide, together with another 29 important new line extensions. Another 19 products were approved for the first time during the year but not yet launched by December 23. Furthermore, during the now-traditional year-end sprint, several regulatory agencies issued last-minute approvals for other compounds that missed the deadline for inclusion in that article, bringing the total of new approvals for the year to a somewhat higher number. In addition to the successful development, registration and launch of new drugs and biologics, there are various other trends and tendencies that serve as indicators of the overall health and status of the industry. These include the pursuit of novel programs designed by regulators to stimulate the development of drugs for diseases that are currently under-treated; the regular and pragmatic culling by companies of their R&D pipelines; and the decision to unify pipelines, portfolios and sales forces through mergers and acquisitions. Copyright 2015 Prous Science, S.A.U. or its licensors. All rights reserved.

  8. Histologic features of alopecias: part II: scarring alopecias.

    Science.gov (United States)

    Bernárdez, C; Molina-Ruiz, A M; Requena, L

    2015-05-01

    The diagnosis of disorders of the hair and scalp can generally be made on clinical grounds, but clinical signs are not always diagnostic and in some cases more invasive techniques, such as a biopsy, may be necessary. This 2-part article is a detailed review of the histologic features of the main types of alopecia based on the traditional classification of these disorders into 2 major groups: scarring and nonscarring alopecias. Scarring alopecias are disorders in which the hair follicle is replaced by fibrous scar tissue, a process that leads to permanent hair loss. In nonscarring alopecias, the follicles are preserved and hair growth can resume when the cause of the problem is eliminated. In the second part of this review, we describe the histologic features of the main forms of scarring alopecia. Since a close clinical-pathological correlation is essential for making a correct histopathologic diagnosis of alopecia, we also include a brief description of the clinical features of the principal forms of this disorder. Copyright © 2014 Elsevier España, S.L.U. and AEDV. All rights reserved.

  9. The simulation of transients in thermal plant. Part II: Applications

    International Nuclear Information System (INIS)

    Morini, G.L.; Piva, S.

    2008-01-01

    This paper deals with the simulation of the transients of thermal plant with control systems. In the companion paper forming part I of this article [G.L. Morini, S. Piva, The simulation of transients in thermal plant. Part I: Mathematical model, Applied Thermal Engineering 27 (2007) 2138-2144] it has been described how a 'thermal-library' of customised blocks can be built and used, in an intuitive way, to study the transients of any kind of thermal plant. Each component of plant such as valves, boilers, and pumps, is represented by a single block. In this paper, the 'thermal-library' approach is demonstrated by the analysis of the dynamic behaviour of a central heating plant of a typical apartment house during a sinusoidal variation of the external temperature. A comparison of the behaviour of such a plant with three way valve working either in flow rate or in temperature control, is presented and discussed. Finally, the results show the delaying effect of the thermal capacity of the building on the performance of the control system

  10. Influence of iron-bearing phyllosilicates on the dechlorination kinetics of 1,1,1-trichloroethane in Fe(II)/cement slurries.

    Science.gov (United States)

    Jung, Bahngmi; Batchelor, Bill

    2007-07-01

    This study examines the effect of iron-bearing phyllosilicates on dechlorination rates of chlorinated aliphatic hydrocarbons (CAHs) in iron-based degradative solidification/stabilization (DS/S-Fe(II)). Laboratory batch experiments were conducted to evaluate dechlorination rates of 1,1,1-trichloroethane (1,1,1-TCA) in a mixture solution of Fe(II), cement and three different iron-bearing phyllosilicates (biotite, vermiculite, and montmorillonite). A first-order rate model was generally used to describe the dechlorination kinetics and the rate constants were dependent on soil mineral type (biotite, vermiculite, and montmorillonite), Fe(II) dose, and the mass ratio of cement to soil mineral. The pseudo-first-order rate constant for montmorillonite was lower than that for biotite and vermiculite by factors of 11-27 when the mass ratio of cement to phyllosilicates was fixed at one. The presence of biotite and vermiculite increase and the presence of montmorillonite decrease the degradation rate that would be observed in their absence. The effect of cement/mineral ratio on rate constants with three different soil minerals indicates that biotite was more reactive than the other two phyllosilicates. This may be due to high accessible natural Fe(II) content in biotite. Montmorillonite appears to inhibit dechlorination by either inactivating Fe(II) by ion exchange or by physically blocking active sites on cement hydration products.

  11. Tetra- and octa-[4-(2-hydroxyethyl)phenoxy bearing novel metal-free and zinc(II) phthalocyanines: Synthesis, characterization and investigation of photophysicochemical properties

    Energy Technology Data Exchange (ETDEWEB)

    Köksoy, Baybars [Marmara University, Department of Chemistry, 34722 Kadıköy, Istanbul (Turkey); Durmuş, Mahmut [Gebze Technical University, Department of Chemistry, 41400 Gebze, Kocaeli (Turkey); Bulut, Mustafa, E-mail: mbulut@marmara.edu.tr [Marmara University, Department of Chemistry, 34722 Kadıköy, Istanbul (Turkey)

    2015-05-15

    In this study, four novel phthalonitriles (1–4) and their corresponding metal-free (5–8) and zinc(II) phthalocyanine derivatives (9–12) bearing 4-(hydroxyethyl)phenoxy groups were synthesized. These novel compounds were characterized by IR, elemental analyses, {sup 1}H-NMR, UV–vis, and MALDI-TOF spectral data. Furthermore, photophysical (fluorescence quantum yields and lifetimes) and photochemical properties (singlet oxygen generation and photodegradation quantum yields) of these phthalocyanines were investigated in dimethylsulfoxide. The studied zinc(II) phthalocyanines generated highly singlet oxygen which is very important for the photodynamic therapy (PDT) of cancer. The fluorescence quenching behaviour of the newly synthesized phthalocyanine compounds were also investigated using 1,4-benzoquinone. - Highlights: • Octa and tetra 4-(hydroxyethyl)phenoxy substituted metal-free and zinc(II) phthalocyanines. • Study of photophysicochemical properties of eight new phthalocyanines. • Highly singlet oxygen generation for novel zinc(II) phthalocyanine photosensitizers.

  12. Revisiting the description of Protein-Protein interfaces. Part II: Experimental study

    OpenAIRE

    Cazals , Frédéric; Proust , Flavien

    2006-01-01

    This paper provides a detailed experimental study of an interface model developed in the companion article F. Cazals and F. Proust, Revisiting the description of Protein-Protein interfaces. Part I: algorithms. Our experimental study is concerned with the usual database of protein-protein complexes, split into five families (Proteases, Immune system, Enzyme Complexes, Signal transduction, Misc.) Our findings, which bear some contradictions with usual statements are the following: (i)Connectivi...

  13. Complex dynamics in diatomic molecules. Part II: Quantum trajectories

    International Nuclear Information System (INIS)

    Yang, C.-D.; Weng, H.-J.

    2008-01-01

    The second part of this paper deals with quantum trajectories in diatomic molecules, which has not been considered before in the literature. Morse potential serves as a more accurate function than a simple harmonic oscillator for illustrating a realistic picture about the vibration of diatomic molecules. However, if we determine molecular dynamics by integrating the classical force equations derived from a Morse potential, we will find that the resulting trajectories do not consist with the probabilistic prediction of quantum mechanics. On the other hand, the quantum trajectory determined by Bohmian mechanics [Bohm D. A suggested interpretation of the quantum theory in terms of hidden variable. Phys. Rev. 1952;85:166-179] leads to the conclusion that a diatomic molecule is motionless in all its vibrational eigen-states, which also contradicts probabilistic prediction of quantum mechanics. In this paper, we point out that the quantum trajectory of a diatomic molecule completely consistent with quantum mechanics does exist and can be solved from the quantum Hamilton equations of motion derived in Part I, which is based on a complex-space formulation of fractal spacetime [El Naschie MS. A review of E-Infinity theory and the mass spectrum of high energy particle physics. Chaos, Solitons and Fractals 2004;19:209-36; El Naschie MS. E-Infinity theory - some recent results and new interpretations. Chaos, Solitons and Fractals 2006;29:845-853; El Naschie MS. The concepts of E-infinity. An elementary introduction to the cantorian-fractal theory of quantum physics. Chaos, Solitons and Fractals 2004;22:495-511; El Naschie MS. SU(5) grand unification in a transfinite form. Chaos, Solitons and Fractals 2007;32:370-374; Nottale L. Fractal space-time and microphysics: towards a theory of scale relativity. Singapore: World Scientific; 1993; Ord G. Fractal space time and the statistical mechanics of random works. Chaos, Soiltons and Fractals 1996;7:821-843] approach to quantum

  14. Towards automated diffraction tomography. Part II-Cell parameter determination

    International Nuclear Information System (INIS)

    Kolb, U.; Gorelik, T.; Otten, M.T.

    2008-01-01

    Automated diffraction tomography (ADT) allows the collection of three-dimensional (3d) diffraction data sets from crystals down to a size of only few nanometres. Imaging is done in STEM mode, and diffraction data are collected with quasi-parallel beam nanoelectron diffraction (NED). Here, we present a set of developed processing steps necessary for automatic unit-cell parameter determination from the collected 3d diffraction data. Cell parameter determination is done via extraction of peak positions from a recorded data set (called the data reduction path) followed by subsequent cluster analysis of difference vectors. The procedure of lattice parameter determination is presented in detail for a beam-sensitive organic material. Independently, we demonstrate a potential (called the full integration path) based on 3d reconstruction of the reciprocal space visualising special structural features of materials such as partial disorder. Furthermore, we describe new features implemented into the acquisition part

  15. [Scientific reductionism and social control of mind. Part II].

    Science.gov (United States)

    Viniegra Velázquez, Leonardo

    In the second part of this essay, the progressive subordination of scientific endeavor and knowledge of business and profit is pointed out. For instance, the way facts are prioritized over concepts and ideas in scientific knowledge can translate into technological innovation, central to enterprise competitiveness and key to social mechanisms of control (military, cybernetic, ideological). Overcoming the scientific reductionism approach indicates recognizing the need to define progress in another way, one that infuses scientific knowledge with real liberating and inquisitive power. Power is essential in the search for a more collaborative, inclusive and pluralistic society where respect for human dignity and care for the ecosystem that we live in are prioritized. Copyright © 2014 Hospital Infantil de México Federico Gómez. Publicado por Masson Doyma México S.A. All rights reserved.

  16. The Mechanism of Graviton Exchange between Bodies, Part II

    DEFF Research Database (Denmark)

    Javadi, Hossein; Forouzbakhsh, Farshid

    2016-01-01

    Further to Special Relativity, modern physics includes two great theories which describe universe in a new different way. One of them is Quantum Mechanics which describes elementary particles, atoms and molecules and the other one is General Relativity which has been replaced the Newtonian...... Gravitational Law by space-time curvature. Quantum gravity is a part of quantum mechanics which is expected to combine these two theories, and it describes gravity force according to the principles of quantum mechanics which has not got the desired result, yet. In CPH theory, after reconsidering and analyzing...... the behavior of photon in the gravitational field, a new definition of graviton based on carrying the gravity force is given. By using this definition, graviton exchange mechanism between bodies/objects is described. As the purpose of quantum gravity is describing the force of gravity by using the principles...

  17. Pulmonary Surfactants for Acute and Chronic Lung Diseases (Part II

    Directory of Open Access Journals (Sweden)

    O. A. Rozenberg

    2014-01-01

    Full Text Available Part 2 of the review considers the problem of surfactant therapy for acute respiratory distress syndrome (ARDS in adults and young and old children. It gives information on the results of surfactant therapy and prevention of ARDS in patients with severe concurrent trauma, inhalation injuries, complications due to complex expanded chest surgery, or severe pneumonias, including bilateral pneumonia in the presence of A/H1N1 influenza. There are data on the use of a surfactant in obstetric care and prevention of primary graft dysfunction during lung transplantation. The results of longterm use of surfactant therapy in Russia, suggesting that death rates from ARDS may be substantially reduced (to 20% are discussed. Examples of surfactant therapy for other noncritical lung diseases, such as permanent athelectasis, chronic obstructive pulmonary diseases, and asthma, as well tuberculosis, are also considered.

  18. On the problem of ethnophyletism: a historical study. Part II

    Directory of Open Access Journals (Sweden)

    Venediktov Vadim Yuriyevich

    2016-12-01

    Full Text Available The Holy and Great Council on Crete, 2016 has risen an important issue of Ethnophyletism. Russian, Georgian, Bulgarian, and Antiochian Orthodox Churches delegations were not present at the Great Council and were criticized for Ethnophyletism at the plenary session. The heresy of ethnophyletism was announced by the Council of Constantinople in 1872. Now we can see that it became essential nowadays. The article tells about the origin of this heresy and whether the Ethnophyletism may be decided to be the heresy. The second part of the paper deals with the events on the eve of the Pan-Orthodox Synod in 1872 (since the manifestation of the famous Abdülaziz Sultan's Firman 1870.

  19. Surface grafted chitosan gels. Part II. Gel formation and characterization

    DEFF Research Database (Denmark)

    Liu, Chao; Thormann, Esben; Claesson, Per M.

    2014-01-01

    Responsive biomaterial hydrogels attract significant attention due to their biocompatibility and degradability. In order to make chitosan based gels, we first graft one layer of chitosan to silica, and then build a chitosan/poly(acrylic acid) multilayer using the layer-by-layer approach. After...... cross-linking the chitosan present in the polyelectrolyte multilayer, poly(acrylic acid) is partly removed by exposing the multilayer structure to a concentrated carbonate buffer solution at a high pH, leaving a surface-grafted cross-linked gel. Chemical cross-linking enhances the gel stability against...... detachment and decomposition. The chemical reaction between gluteraldehyde, the cross-linking agent, and chitosan was followed in situ using total internal reflection Raman (TIRR) spectroscopy, which provided a molecular insight into the complex reaction mechanism, as well as the means to quantify the cross...

  20. One-loop effective actions and higher spins. Part II

    Science.gov (United States)

    Bonora, L.; Cvitan, M.; Prester, P. Dominis; Giaccari, S.; Štemberga, T.

    2018-01-01

    In this paper we continue and improve the analysis of the effective actions obtained by integrating out a scalar and a fermion field coupled to external symmetric sources, started in the previous paper. The first subject we study is the geometrization of the results obtained there, that is we express them in terms of covariant Jacobi tensors. The second subject concerns the treatment of tadpoles and seagull terms in order to implement off-shell covariance in the initial model. The last and by far largest part of the paper is a repository of results concerning all two point correlators (including mixed ones) of symmetric currents of any spin up to 5 and in any dimensions between 3 and 6. In the massless case we also provide formulas for any spin in any dimension.

  1. PERICARDITIS: ETIOLOGY, CLASSIFICATION, CLINIC, DIAGNOSTICS, TREATMENT. PART II

    Directory of Open Access Journals (Sweden)

    A.B. Sugak

    2009-01-01

    Full Text Available Pericarditis maybe caused by different agents: viruses, bacteria, tuberculosis, and it may be autoimmune. All these types of diseases have similar clinical signs, but differ by prevalence, prognosis and medical tactics. Due to achievements of radial methods of visualization, molecular biology, and immunology, we have an opportunity to provide early specific diagnostics and etiological treatment of inflammatory diseases of pericardium. The second part of lecture presents main principles of differential diagnostics of specific types of pericarditis, gives characteristics of several often accruing types of disease, and describes treatment and tactics of management of patients with pericarditis.Key words: children, pericarditis.(Voprosy sovremennoi pediatrii — Current Pediatrics. 2009;8(3:76-81

  2. Study of the oil flow and the bearing temperature in engine. Part 3. Influence of the bearing designs; Engine ni okeru jikuuke yuryo oyobi jikuuke ondo ni kansuru ichikosatsu. 3. Jikuuke sekkei yoso no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, K; Kawai, K; Sasaki, S [Taiho Kogyo Co. Ltd., Aichi (Japan)

    1997-10-01

    It is necessary to find the bearing design so that the bearing temperature drops most efficiently by making the proper oil flow. We measured the oil flow and the bearing temperature using the narrow width bearing the bearing with small oil relief , the bearing with shallow circumferential microgrooves (the microgrooved bearing), the narrow width bearing with microgrooves. And further, we measured the variation of the oil flow every 5-15deg crank angle and searched for the efficient oil flow. As the result the bearing temperature using the microgrooved bearing dropped most efficiently. 3 refs., 13 figs., 5 tabs.

  3. Process maps for plasma spray. Part II: Deposition and properties

    International Nuclear Information System (INIS)

    XIANGYANG, JIANG; MATEJICEK, JIRI; KULKARNI, ANAND; HERMAN, HERBERT; SAMPATH, SANJAY; GILMORE, DELWYN L.; NEISER A, RICHARD Jr.

    2000-01-01

    This is the second paper of a two part series based on an integrated study carried out at the State University of New York at Stony Brook and Sandia National Laboratories. The goal of the study is the fundamental understanding of the plasma-particle interaction, droplet/substrate interaction, deposit formation dynamics and microstructure development as well as the deposit property. The outcome is science-based relationships, which can be used to link processing to performance. Molybdenum splats and coatings produced at 3 plasma conditions and three substrate temperatures were characterized. It was found that there is a strong mechanical/thermal interaction between droplet and substrate, which builds up the coatings/substrate adhesion. Hardness, thermal conductivity, and modulus increase, while oxygen content and porosity decrease with increasing particle velocity. Increasing deposition temperature resulted in dramatic improvement in coating thermal conductivity and hardness as well as increase in coating oxygen content. Indentation reveals improved fracture resistance for the coatings prepared at higher deposition temperature. Residual stress was significantly affected by deposition temperature, although not significant by particle energy within the investigated parameter range. Coatings prepared at high deposition temperature with high-energy particles suffered considerably less damage in wear tests. Possible mechanisms behind these changes are discussed within the context of relational maps which are under development

  4. Advanced statistics: linear regression, part II: multiple linear regression.

    Science.gov (United States)

    Marill, Keith A

    2004-01-01

    The applications of simple linear regression in medical research are limited, because in most situations, there are multiple relevant predictor variables. Univariate statistical techniques such as simple linear regression use a single predictor variable, and they often may be mathematically correct but clinically misleading. Multiple linear regression is a mathematical technique used to model the relationship between multiple independent predictor variables and a single dependent outcome variable. It is used in medical research to model observational data, as well as in diagnostic and therapeutic studies in which the outcome is dependent on more than one factor. Although the technique generally is limited to data that can be expressed with a linear function, it benefits from a well-developed mathematical framework that yields unique solutions and exact confidence intervals for regression coefficients. Building on Part I of this series, this article acquaints the reader with some of the important concepts in multiple regression analysis. These include multicollinearity, interaction effects, and an expansion of the discussion of inference testing, leverage, and variable transformations to multivariate models. Examples from the first article in this series are expanded on using a primarily graphic, rather than mathematical, approach. The importance of the relationships among the predictor variables and the dependence of the multivariate model coefficients on the choice of these variables are stressed. Finally, concepts in regression model building are discussed.

  5. Modeling multibody systems with uncertainties. Part II: Numerical applications

    International Nuclear Information System (INIS)

    Sandu, Corina; Sandu, Adrian; Ahmadian, Mehdi

    2006-01-01

    This study applies generalized polynomial chaos theory to model complex nonlinear multibody dynamic systems operating in the presence of parametric and external uncertainty. Theoretical and computational aspects of this methodology are discussed in the companion paper 'Modeling Multibody Dynamic Systems With Uncertainties. Part I: Theoretical and Computational Aspects .In this paper we illustrate the methodology on selected test cases. The combined effects of parametric and forcing uncertainties are studied for a quarter car model. The uncertainty distributions in the system response in both time and frequency domains are validated against Monte-Carlo simulations. Results indicate that polynomial chaos is more efficient than Monte Carlo and more accurate than statistical linearization. The results of the direct collocation approach are similar to the ones obtained with the Galerkin approach. A stochastic terrain model is constructed using a truncated Karhunen-Loeve expansion. The application of polynomial chaos to differential-algebraic systems is illustrated using the constrained pendulum problem. Limitations of the polynomial chaos approach are studied on two different test problems, one with multiple attractor points, and the second with a chaotic evolution and a nonlinear attractor set. The overall conclusion is that, despite its limitations, generalized polynomial chaos is a powerful approach for the simulation of multibody dynamic systems with uncertainties

  6. The Role of Regulatory Agencies and Intellectual Property: Part II

    Science.gov (United States)

    Noonan, Kevin E.

    2015-01-01

    Patent law and antitrust law have traditionally been areas of the law involving at least some inherent tension. Champions of antitrust argue that the patent “monopoly” must be strictly limited as an exception to the general legal principle that competition should be unfettered. Patent lawyers argue that patents are the result of an exercise of congressional authority, enshrined in the Constitution, reflecting the policy decision by the Founders that granting a limited exclusionary right was justified by the public benefits derived from full disclosure of the patented invention. In the modern era these competing values have played out in the context of so-called ANDA litigation, involving disputes between branded pharmaceutical companies and generic competitors. Settlement of such litigation has been identified by the Federal Trade Commission (FTC), and private parties encouraged by the FTC’s position, as an antitrust violation, in large part because such settlements are viewed as frustrating the congressional purpose in promoting early generic competition. After almost a decade of fighting these battles in the federal courts, the Supreme Court addressed the issue directly. The result is that such settlements are not per se illegal but are also not protected by the presumption of patent validity for activities within the “scope of the patent.” Rather, the court decided that these agreements should be assessed for antitrust liability under the “rule of reason” used in other antitrust contexts. PMID:25775920

  7. Modeling multibody systems with uncertainties. Part II: Numerical applications

    Energy Technology Data Exchange (ETDEWEB)

    Sandu, Corina, E-mail: csandu@vt.edu; Sandu, Adrian; Ahmadian, Mehdi [Virginia Polytechnic Institute and State University, Mechanical Engineering Department (United States)

    2006-04-15

    This study applies generalized polynomial chaos theory to model complex nonlinear multibody dynamic systems operating in the presence of parametric and external uncertainty. Theoretical and computational aspects of this methodology are discussed in the companion paper 'Modeling Multibody Dynamic Systems With Uncertainties. Part I: Theoretical and Computational Aspects .In this paper we illustrate the methodology on selected test cases. The combined effects of parametric and forcing uncertainties are studied for a quarter car model. The uncertainty distributions in the system response in both time and frequency domains are validated against Monte-Carlo simulations. Results indicate that polynomial chaos is more efficient than Monte Carlo and more accurate than statistical linearization. The results of the direct collocation approach are similar to the ones obtained with the Galerkin approach. A stochastic terrain model is constructed using a truncated Karhunen-Loeve expansion. The application of polynomial chaos to differential-algebraic systems is illustrated using the constrained pendulum problem. Limitations of the polynomial chaos approach are studied on two different test problems, one with multiple attractor points, and the second with a chaotic evolution and a nonlinear attractor set. The overall conclusion is that, despite its limitations, generalized polynomial chaos is a powerful approach for the simulation of multibody dynamic systems with uncertainties.

  8. Oral health in Brazil - Part II: Dental Specialty Centers (CEOs

    Directory of Open Access Journals (Sweden)

    Vinícius Pedrazzi

    2008-08-01

    Full Text Available The concepts of health promotion, self-care and community participation emerged during the 1970s and, since then, their application has grown rapidly in the developed world, showing evidence of effectiveness. In spite of this, a major part of the population in the developing countries still has no access to specialized dental care such as endodontic treatment, dental care for patients with special needs, minor oral surgery, periodontal treatment and oral diagnosis. This review focuses on a program of the Brazilian Federal Government named CEOs (Dental Specialty Centers, which is an attempt to solve the dental care deficit of a population that is suffering from oral diseases and whose oral health care needs have not been addressed by the regular programs offered by the SUS (Unified National Health System. Literature published from 2000 to the present day, using electronic searches by Medline, Scielo, Google and hand-searching was considered. The descriptors used were Brazil, Oral health, Health policy, Health programs, and Dental Specialty Centers. There are currently 640 CEOs in Brazil, distributed in 545 municipal districts, carrying out dental procedures with major complexity. Based on this data, it was possible to conclude that public actions on oral health must involve both preventive and curative procedures aiming to minimize the oral health distortions still prevailing in developing countries like Brazil.

  9. A platform for quality management in research institutes (part II

    Directory of Open Access Journals (Sweden)

    Klembalska Agnieszka

    2016-09-01

    Full Text Available In the recent years there has been a particularly strong pressure on changing old structures and management models in research institutes. Contemporary research institutes are scientific units which are commercial in character – almost 80% of funds come from companies and contractual research activity and services. They are the basic sector of science aiming at cooperation with the economy, applied and innovative research. In order to maintain the current and start new cooperation it is necessary to pay particular attention to maintaining, improving and exposing high level of quality of conducted activity. Taking into consideration the necessity of carrying out ever more complex research projects, conducting activity requiring fast reaction to change, risk analysis, which is assessed every year by the Ministry of Science and Higher Education – it seems that it is necessary to apply tools supporting the assessment of quality. In the proposed three-aspect perspective the following scopes of activity are emphasized: implemented quality management systems, area of scientific information and the sphere of cooperation with the client. This article constitutes the continuation of the subjects discussed in the first part – an extension of issues associated with the scope of responsibilities of particular Sections of the proposed Quality Management Platform in research institutes.

  10. The Role of Regulatory Agencies and Intellectual Property: Part II.

    Science.gov (United States)

    Noonan, Kevin E

    2015-03-16

    Patent law and antitrust law have traditionally been areas of the law involving at least some inherent tension. Champions of antitrust argue that the patent "monopoly" must be strictly limited as an exception to the general legal principle that competition should be unfettered. Patent lawyers argue that patents are the result of an exercise of congressional authority, enshrined in the Constitution, reflecting the policy decision by the Founders that granting a limited exclusionary right was justified by the public benefits derived from full disclosure of the patented invention. In the modern era these competing values have played out in the context of so-called ANDA litigation, involving disputes between branded pharmaceutical companies and generic competitors. Settlement of such litigation has been identified by the Federal Trade Commission (FTC), and private parties encouraged by the FTC's position, as an antitrust violation, in large part because such settlements are viewed as frustrating the congressional purpose in promoting early generic competition. After almost a decade of fighting these battles in the federal courts, the Supreme Court addressed the issue directly. The result is that such settlements are not per se illegal but are also not protected by the presumption of patent validity for activities within the "scope of the patent." Rather, the court decided that these agreements should be assessed for antitrust liability under the "rule of reason" used in other antitrust contexts. Copyright © 2015 Cold Spring Harbor Laboratory Press; all rights reserved.

  11. Practice improvement, part II: update on patient communication technologies.

    Science.gov (United States)

    Roett, Michelle A; Coleman, Mary Thoesen

    2013-11-01

    Patient portals (ie, secure web-based services for patient health record access) and secure messaging to health care professionals are gaining popularity slowly. Advantages of web portals include timely communication and instruction, access to appointments and other services, and high patient satisfaction. Limitations include inappropriate use, security considerations, organizational costs, and exclusion of patients who are uncomfortable with or unable to use computers. Attention to the organization's strategic plan and office policies, patient and staff expectations, workflow and communication integration, training, marketing, and enrollment can facilitate optimal use of this technology. Other communication technologies that can enhance patient care include automated voice or text reminders and brief electronic communications. Social media provide another method of patient outreach, but privacy and access are concerns. Incorporating telehealthcare (health care provided via telephone or Internet), providing health coaching, and using interactive health communication applications can improve patient knowledge and clinical outcomes and provide social support. Written permission from the American Academy of Family Physicians is required for reproduction of this material in whole or in part in any form or medium.

  12. Cyclopentane combustion. Part II. Ignition delay measurements and mechanism validation

    KAUST Repository

    Rachidi, Mariam El

    2017-06-12

    This study reports cyclopentane ignition delay measurements over a wide range of conditions. The measurements were obtained using two shock tubes and a rapid compression machine, and were used to test a detailed low- and high-temperature mechanism of cyclopentane oxidation that was presented in part I of this study (Al Rashidi et al., 2017). The ignition delay times of cyclopentane/air mixtures were measured over the temperature range of 650–1350K at pressures of 20 and 40atm and equivalence ratios of 0.5, 1.0 and 2.0. The ignition delay times simulated using the detailed chemical kinetic model of cyclopentane oxidation show very good agreement with the experimental measurements, as well as with the cyclopentane ignition and flame speed data available in the literature. The agreement is significantly improved compared to previous models developed and investigated at higher temperatures. Reaction path and sensitivity analyses were performed to provide insights into the ignition-controlling chemistry at low, intermediate and high temperatures. The results obtained in this study confirm that cycloalkanes are less reactive than their non-cyclic counterparts. Moreover, cyclopentane, a high octane number and high octane sensitivity fuel, exhibits minimal low-temperature chemistry and is considerably less reactive than cyclohexane. This study presents the first experimental low-temperature ignition delay data of cyclopentane, a potential fuel-blending component of particular interest due to its desirable antiknock characteristics.

  13. Cyclopentane combustion. Part II. Ignition delay measurements and mechanism validation

    KAUST Repository

    Rachidi, Mariam El; Má rmol, Juan C.; Banyon, Colin; Sajid, Muhammad Bilal; Mehl, Marco; Pitz, William J.; Mohamed, Samah; Alfazazi, Adamu; Lu, Tianfeng; Curran, Henry J.; Farooq, Aamir; Sarathy, Mani

    2017-01-01

    This study reports cyclopentane ignition delay measurements over a wide range of conditions. The measurements were obtained using two shock tubes and a rapid compression machine, and were used to test a detailed low- and high-temperature mechanism of cyclopentane oxidation that was presented in part I of this study (Al Rashidi et al., 2017). The ignition delay times of cyclopentane/air mixtures were measured over the temperature range of 650–1350K at pressures of 20 and 40atm and equivalence ratios of 0.5, 1.0 and 2.0. The ignition delay times simulated using the detailed chemical kinetic model of cyclopentane oxidation show very good agreement with the experimental measurements, as well as with the cyclopentane ignition and flame speed data available in the literature. The agreement is significantly improved compared to previous models developed and investigated at higher temperatures. Reaction path and sensitivity analyses were performed to provide insights into the ignition-controlling chemistry at low, intermediate and high temperatures. The results obtained in this study confirm that cycloalkanes are less reactive than their non-cyclic counterparts. Moreover, cyclopentane, a high octane number and high octane sensitivity fuel, exhibits minimal low-temperature chemistry and is considerably less reactive than cyclohexane. This study presents the first experimental low-temperature ignition delay data of cyclopentane, a potential fuel-blending component of particular interest due to its desirable antiknock characteristics.

  14. Predicting performance in competitive apnea diving, part II: dynamic apnoea.

    Science.gov (United States)

    Schagatay, Erika

    2010-03-01

    Part I of this series of articles identified the main physiological factors defining the limits of static apnea, while this paper reviews the factors involved when physical work is added in the dynamic distance disciplines, performed in shallow water in a swimming pool. Little scientific work has been done concerning the prerequisites and limitations of swimming with or without fins whilst breath holding to extreme limits. Apneic duration influences all competitive apnea disciplines, and can be prolonged by any means that increase gas storage or tolerance to asphyxia, or reduce metabolic rate, as reviewed in the first article. For horizontal underwater distance swimming, the main challenge is to restrict metabolism despite the work, and to direct blood flow only to areas where demand is greatest, to allow sustained function. Here, work economy, local tissue energy and oxygen stores and the anaerobic capacity of the muscles are key components. Improvements in swimming techniques and, especially in swimming with fins, equipment have already contributed to enhanced performance and may do so further. High lactate levels observed after competition swims suggest a high anaerobic component, and muscle hypoxia could ultimately limit muscle work and swimming distance. However, the frequency of syncope, especially in swimming without fins, suggests that cerebral oxygenation may often be compromised before this occurs. In these pool disciplines, safety is high and the dive can be interrupted by the competitor or safety diver within seconds. The safety routines in place during pool competitions are described.

  15. Practice improvement, part II: trends in employment versus private practice.

    Science.gov (United States)

    Coleman, Mary Thoesen; Roett, Michelle A

    2013-11-01

    A growing percentage of physicians are selecting employment over solo practice, and fewer family physicians have hospital admission privileges. Results from surveys of recent medical school graduates indicate a high value placed on free time. Factors to consider when choosing a practice opportunity include desire for independence, decision-making authority, work-life balance, administrative responsibilities, financial risk, and access to resources. Compensation models are evolving from the simple fee-for-service model to include metrics that reward panel size, patient access, coordination of care, chronic disease management, achievement of patient-centered medical home status, and supervision of midlevel clinicians. When a practice is sold, tangible personal property and assets in excess of liabilities, patient accounts receivable, office building, and goodwill (ie, expected earnings) determine its value. The sale of a practice includes a broad legal review, addressing billing and coding deficiencies, noncompliant contractual arrangements, and potential litigations as well as ensuring that all employment agreements, leases, service agreements, and contracts are current, have been executed appropriately, and meet regulatory requirements. Written permission from the American Academy of Family Physicians is required for reproduction of this material in whole or in part in any form or medium.

  16. Recent applications of nuclear medicine in diagnostics: II part

    Directory of Open Access Journals (Sweden)

    Giorgio Treglia

    2013-04-01

    Full Text Available Introduction: Positron-emission tomography (PET and single photon emission computed tomography (SPECT are effective diagnostic imaging tools in several clinical settings. The aim of this article (the second of a 2-part series is to examine some of the more recent applications of nuclear medicine imaging techniques, particularly in the fields of neurology, cardiology, and infection/inflammation. Discussion: A review of the literature reveals that in the field of neurology nuclear medicine techniques are most widely used to investigate cognitive deficits and dementia (particularly those associated with Alzheimer disease, epilepsy, and movement disorders. In cardiology, SPECT and PET also play important roles in the work-up of patients with coronary artery disease, providing accurate information on the state of the myocardium (perfusion, metabolism, and innervation. White blood cell scintigraphy and FDG-PET are widely used to investigate many infectious/inflammatory processes. In each of these areas, the review discusses the use of recently developed radiopharmaceuticals, the growth of tomographic nuclear medicine techniques, and the ways in which these advances are improving molecular imaging of biologic processes at the cellular level.

  17. Operational hydrological forecasting in Bavaria. Part II: Ensemble forecasting

    Science.gov (United States)

    Ehret, U.; Vogelbacher, A.; Moritz, K.; Laurent, S.; Meyer, I.; Haag, I.

    2009-04-01

    In part I of this study, the operational flood forecasting system in Bavaria and an approach to identify and quantify forecast uncertainty was introduced. The approach is split into the calculation of an empirical 'overall error' from archived forecasts and the calculation of an empirical 'model error' based on hydrometeorological forecast tests, where rainfall observations were used instead of forecasts. The 'model error' can especially in upstream catchments where forecast uncertainty is strongly dependent on the current predictability of the atrmosphere be superimposed on the spread of a hydrometeorological ensemble forecast. In Bavaria, two meteorological ensemble prediction systems are currently tested for operational use: the 16-member COSMO-LEPS forecast and a poor man's ensemble composed of DWD GME, DWD Cosmo-EU, NCEP GFS, Aladin-Austria, MeteoSwiss Cosmo-7. The determination of the overall forecast uncertainty is dependent on the catchment characteristics: 1. Upstream catchment with high influence of weather forecast a) A hydrological ensemble forecast is calculated using each of the meteorological forecast members as forcing. b) Corresponding to the characteristics of the meteorological ensemble forecast, each resulting forecast hydrograph can be regarded as equally likely. c) The 'model error' distribution, with parameters dependent on hydrological case and lead time, is added to each forecast timestep of each ensemble member d) For each forecast timestep, the overall (i.e. over all 'model error' distribution of each ensemble member) error distribution is calculated e) From this distribution, the uncertainty range on a desired level (here: the 10% and 90% percentile) is extracted and drawn as forecast envelope. f) As the mean or median of an ensemble forecast does not necessarily exhibit meteorologically sound temporal evolution, a single hydrological forecast termed 'lead forecast' is chosen and shown in addition to the uncertainty bounds. This can be

  18. Synopsis Of The subfamily Spiranthoideae (Orchidaceae) In Colombia, Part II

    International Nuclear Information System (INIS)

    Duenas Gomez, Hilda del Carmen; Fernandez Alonso, Jose Luis

    2009-01-01

    As second and last contribution to the synoptic treatment of the Spiranthoideae for Colombia, the synopsis of the tribes Spirantheae (subtribes Cyclopogoninae: 3 genera, 41 species and Stenorrhynchidinae: 9 genera, 15 species) and Cranichideae (5 genera, 53 species), is presented. The most diverse genera in these tribes are: Cranichis (20 species), Cyclopogon (17), Ponthieva (15) and Pelexia (14). As part of the results of this study: a)- The transfer of Cybebus from the subtribe Spiranthinae (where it was commonly placed) to the subtribe Stenorhinchidinae, is proposed, based on the floral morphology (the rostellum and viscidium structure). b)- two genera are reported for Colombia as new records, each one with one species: Lyroglossa (L. grisebachii) and Helonoma; for the latter the new combination Helonoma peruviana (Szlach.) Salazar, Duenas and Fern. Alonso is proposed. c) New records in the previously known list of Colombian orchids are presented: Coccineorchis (C. cristata, C. navarrensis), Cyclopogon (C. maldonadoanus, C. olivaceus, C. rimbachii), Pelexia (P. hirta, P. palmorchidis), Ponthieva (P. venusta), and Sarcoglottis (S. grandiflora, S. maasorum, S. neglecta, S. stergiosii). d)- And additional 19 new records of species belonging to Aspidogyne and Microchilus, not reported in Duenas and Fernandez-Alonso (2007), are also included. e)- Finally an analysis of the distribution and diversity of the genera of this subfamily, according to altitude ranges in Colombia is presented. This group has predominant Andean distribution, being found mainly between 1300 and 3600 m of altitude. Genera broadly distributed as Microchilus, Gomphichis, Cyclopogon, Pelexia, Sarcoglottis, Coccineorchis, Stenorrhynchos, Cranichis and Ponthieva, are found almost from the level up to 3000 m, in all the regions of the country. In contrast, Beloglottis, Brachystele, Cybebus, Eltroplectris, Hapalorchis, Helonoma, Lankesterella, Lyroglossa, Kreodanthus, Pteroglossa and Sauroglossum

  19. FNR demonstration experiments Part II: Subcadmium neutron flux measurements

    International Nuclear Information System (INIS)

    Wehe, D.K.; King, J.S.

    1983-01-01

    The FNR HEU-LEU Demonstration Experiments include a comprehensive set of experiments to identify and quantify significant operational differences between two nuclear fuel enrichments. One aspect of these measurements, the subcadmium flux profiling, is the subject of this paper. The flux profiling effort has been accomplished through foil and wire activations, and by rhodium self-powered neutron detector (SPND) mappings. Within the experimental limitations discussed, the program to measure subcadmium flux profiles, lead to the following conclusions: (1) Replacement of a single fresh HEU element by a fresh LEU element at the center of an equilibrium HEU core produces a local flux depression. The ratio of HEU to LEU local flux is 1.19 ± .036, which is, well within experimental uncertainty, equal to the inverse of the U-235 masses for the two elements. (2) Whole core replacement of a large 38 element equilibrium HEU core by a fresh or nearly unburned LEU core reduces the core flux and raises the flux in both D 2 O and H 2 O reflectors. The reduction in the central core region is 40% to 10.0% for the small fresh 29 element LEU core, and 16% to 18% for a 31 element LEU core 482) with low average burnup 2 O reflector fluxes relative to core fluxes as measured by SPND with a fixed value of sensitivity, are in gross disagreement with the same flux ratios measured by Fe and Rh wire activations. Space dependent refinements of S are calculated to give some improvement in the discrepancy but the major part of the correction remains to be resolved

  20. Stress analysis in oral obturator prostheses, part II: photoelastic imaging

    Science.gov (United States)

    Pesqueira, Aldiéris Alves; Goiato, Marcelo Coelho; da Silva, Emily Vivianne Freitas; Haddad, Marcela Filié; Moreno, Amália; Zahoui, Abbas; dos Santos, Daniela Micheline

    2014-06-01

    In part I of the study, two attachment systems [O-ring; bar-clip (BC)] were used, and the system with three individualized O-rings provided the lowest stress on the implants and the support tissues. Therefore, the aim of this study was to assess the stress distribution, through the photoelastic method, on implant-retained palatal obturator prostheses associated with different attachment systems: BOC-splinted implants with a bar connected to two centrally placed O-rings, and BOD-splinted implants with a BC connected to two distally placed O-rings (cantilever). One photoelastic model of the maxilla with oral-sinus-nasal communication with three parallel implants was fabricated. Afterward, two implant-retained palatal obturator prostheses with the two attachment systems described above were constructed. Each assembly was positioned in a circular polariscope and a 100-N axial load was applied in three different regions with implants by using a universal testing machine. The results were obtained through photograph record analysis of stress. The BOD system exhibited the highest stress concentration, followed by the BOC system. The O-ring, centrally placed on the bar, allows higher mobility of the prostheses and homogeneously distributes the stress to the region of the alveolar ridge and implants. It can be concluded that the use of implants with O-rings, isolated or connected with a bar, to rehabilitate maxillectomized patients allows higher prosthesis mobility and homogeneously distributes the stress to the alveolar ridge region, which may result in greater chewing stress distribution to implants and bone tissue. The clinical implication of the augmented bone support loss after maxillectomy is the increase of stress in the attachment systems and, consequently, a higher tendency for displacement of the prosthesis.

  1. Overactive bladder – 18 years – Part II

    Directory of Open Access Journals (Sweden)

    Jose Carlos Truzzi

    2016-04-01

    Full Text Available ABSTRACT Traditionally, the treatment of overactive bladder syndrome has been based on the use of oral medications with the purpose of reestablishing the detrusor stability. The recent better understanding of the urothelial physiology fostered conceptual changes, and the oral anticholinergics – pillars of the overactive bladder pharmacotherapy – started to be not only recognized for their properties of inhibiting the detrusor contractile activity, but also their action on the bladder afference, and therefore, on the reduction of the symptoms that constitute the syndrome. Beta-adrenergic agonists, which were recently added to the list of drugs for the treatment of overactive bladder, still wait for a definitive positioning – as either a second-line therapy or an adjuvant to oral anticholinergics. Conservative treatment failure, whether due to unsatisfactory results or the presence of adverse side effects, define it as refractory overactive bladder. In this context, the intravesical injection of botulinum toxin type A emerged as an effective option for the existing gap between the primary measures and more complex procedures such as bladder augmentation. Sacral neuromodulation, described three decades ago, had its indication reinforced in this overactive bladder era. Likewise, the electric stimulation of the tibial nerve is now a minimally invasive alternative to treat those with refractory overactive bladder. The results of the systematic literature review on the oral pharmacological treatment and the treatment of refractory overactive bladder gave rise to this second part of the review article Overactive Bladder – 18 years, prepared during the 1st Latin-American Consultation on Overactive Bladder.

  2. Neuromorphic meets neuromechanics, part II: the role of fusimotor drive

    Science.gov (United States)

    Jalaleddini, Kian; Minos Niu, Chuanxin; Chakravarthi Raja, Suraj; Sohn, Won Joon; Loeb, Gerald E.; Sanger, Terence D.; Valero-Cuevas, Francisco J.

    2017-04-01

    Objective. We studied the fundamentals of muscle afferentation by building a Neuro-mechano-morphic system actuating a cadaveric finger. This system is a faithful implementation of the stretch reflex circuitry. It allowed the systematic exploration of the effects of different fusimotor drives to the muscle spindle on the closed-loop stretch reflex response. Approach. As in Part I of this work, sensory neurons conveyed proprioceptive information from muscle spindles (with static and dynamic fusimotor drive) to populations of α-motor neurons (with recruitment and rate coding properties). The motor commands were transformed into tendon forces by a Hill-type muscle model (with activation-contraction dynamics) via brushless DC motors. Two independent afferented muscles emulated the forces of flexor digitorum profundus and the extensor indicis proprius muscles, forming an antagonist pair at the metacarpophalangeal joint of a cadaveric index finger. We measured the physical response to repetitions of bi-directional ramp-and-hold rotational perturbations for 81 combinations of static and dynamic fusimotor drives, across four ramp velocities, and three levels of constant cortical drive to the α-motor neuron pool. Main results. We found that this system produced responses compatible with the physiological literature. Fusimotor and cortical drives had nonlinear effects on the reflex forces. In particular, only cortical drive affected the sensitivity of reflex forces to static fusimotor drive. In contrast, both static fusimotor and cortical drives reduced the sensitivity to dynamic fusimotor drive. Interestingly, realistic signal-dependent motor noise emerged naturally in our system without having been explicitly modeled. Significance. We demonstrate that these fundamental features of spinal afferentation sufficed to produce muscle function. As such, our Neuro-mechano-morphic system is a viable platform to study the spinal mechanisms for healthy muscle function—and its

  3. Bears, Big and Little. Young Discovery Library Series.

    Science.gov (United States)

    Pfeffer, Pierre

    This book is written for children 5 through 10. Part of a series designed to develop their curiosity, fascinate them and educate them, this volume describes: (1) the eight species of bears, including black bear, brown bear, grizzly bear, spectacled bear, sun bear, sloth bear, polar bear, and giant panda; (2) geographical habitats of bears; (3)…

  4. Three Mile Island: a report to the commissioners and to the public. Volume II, Part 3

    International Nuclear Information System (INIS)

    1979-01-01

    This is the third and final part of the second volume of a study of the Three Mile Island accident. Part 3 of Volume II contains descriptions and assessments of responses to the accident by the utility and by the NRC and other government agencies

  5. PGE Production in Southern Africa, Part II: Environmental Aspects

    Directory of Open Access Journals (Sweden)

    Benedikt Buchspies

    2017-11-01

    Full Text Available Platinum group elements (PGEs, 6E PGE = Pt + Pd + Rh + Ru + Ir + Au are used in numerous applications that seek to reduce environmental impacts of mobility and energy generation. Consequently, the future demand for PGEs is predicted to increase. Previous studies indicate that environmental impacts of PGE production change over time emphasizing the need of up-to-date data and assessments. In this context, an analysis of environmental aspects of PGE production is needed to support the environmental assessment of technologies using PGEs, to reveal environmental hotspots within the production chain and to identify optimization potential. Therefore, this paper assesses greenhouse gas (GHG emissions, cumulative fossil energy demand (CEDfossil, sulfur dioxide (SO2 emissions and water use of primary PGE production in Southern Africa, where most of today’s supply originates from. The analysis shows that in 2015, emissions amounted to 45 t CO2-eq. and 502 kg SO2 per kg 6E PGE in the case GHG and SO2 emissions, respectively. GHG emissions are dominated by emissions from electricity provision contributing more than 90% to the overall GHG emissions. The CEDfossil amounted to 0.60 TJ per kg 6E PGE. A detailed analysis of the CEDfossil reveals that electricity provision based on coal power consumes the most fossil energy carriers among all energy forms. Results show that the emissions are directly related to the electricity demand. Thus, the reduction in the electricity demand presents the major lever to reduce the consumption of fossil energy resources and the emission of GHGs and SO2. In 2015, the water withdrawal amounted to 0.272 million L per kg 6E PGE. Additionally, 0.402 million L of recycled water were used per kg 6E PGE. All assessed indicators except ore grades and production volumes reveal increasing trends in the period from 2010 to 2015. It can be concluded that difficult market conditions (see part I of this paper series and increasing

  6. Non-Lubricated Diamond-Coated Bearings Reinforced by Carbon Fibers to Work in Lunar Dust, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — In Phase I, we made prototype sliding bearings from functionally-graded, diamond-coated carbon-fiber reinforced composite. In dry-sliding experiments, the friction...

  7. PIO I-II tendencies. Part 2. Improving the pilot modeling

    Directory of Open Access Journals (Sweden)

    Ioan URSU

    2011-03-01

    Full Text Available The study is conceived in two parts and aims to get some contributions to the problem ofPIO aircraft susceptibility analysis. Part I, previously published in this journal, highlighted the mainsteps of deriving a complex model of human pilot. The current Part II of the paper considers a properprocedure of the human pilot mathematical model synthesis in order to analyze PIO II typesusceptibility of a VTOL-type aircraft, related to the presence of position and rate-limited actuator.The mathematical tools are those of semi global stability theory developed in recent works.

  8. International Working Group on Fast Reactors Thirteenth Annual Meeting. Summary Report. Part II

    International Nuclear Information System (INIS)

    1980-10-01

    The Thirteenth Annual Meeting of the IAEA International Working Group on Fast Reactors was held at the IAEA Headquarters, Vienna, Austria from 9 to 11 April 1980. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programme in the field of LMFBRs and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

  9. On the Efficiency of Connection Charges---Part II: Integration of Distributed Energy Resources

    OpenAIRE

    Munoz-Alvarez, Daniel; Garcia-Franco, Juan F.; Tong, Lang

    2017-01-01

    This two-part paper addresses the design of retail electricity tariffs for distribution systems with distributed energy resources (DERs). Part I presents a framework to optimize an ex-ante two-part tariff for a regulated monopolistic retailer who faces stochastic wholesale prices on the one hand and stochastic demand on the other. In Part II, the integration of DERs is addressed by analyzing their endogenous effect on the optimal two-part tariff and the induced welfare gains. Two DER integrat...

  10. Synchrotron X-ray CT characterization of titanium parts fabricated by additive manufacturing. Part II. Defects.

    Science.gov (United States)

    Scarlett, Nicola Vivienne Yorke; Tyson, Peter; Fraser, Darren; Mayo, Sheridan; Maksimenko, Anton

    2016-07-01

    Synchrotron X-ray tomography (SXRT) has been applied to the study of defects within three-dimensional printed titanium parts. These parts were made using the Arcam EBM(®) (electron beam melting) process which uses powdered titanium alloy, Ti64 (Ti alloy with approximately 6%Al and 4%V) as the feed and an electron beam for the sintering/welding. The experiment was conducted on the Imaging and Medical Beamline of the Australian Synchrotron. The samples represent a selection of complex shapes with a variety of internal morphologies. Inspection via SXRT has revealed a number of defects which may not otherwise have been seen. The location and nature of such defects combined with detailed knowledge of the process conditions can contribute to understanding the interplay between design and manufacturing strategy. This fundamental understanding may subsequently be incorporated into process modelling, prediction of properties and the development of robust methodologies for the production of defect-free parts.

  11. Contamination smoke: a simulation of heavy metal containing aerosols from fires in plutonium glove boxes: part II

    International Nuclear Information System (INIS)

    Buijs, K.; Chavane de Dalmassy, B.; Baumgaertner, E.

    1992-01-01

    The study of the dispersion of plutonium bearing aerosols during glove box fires on a laboratory scale has been, in part I of this work, focussed on fires of polymethylmethacrylate (PMMA - the major glove box construction material) whose surfaces were contaminated with cerium-europium oxide powder as a substitute for plutonium-uranium oxide. The present part II completes the study with comparative fire experiments involving contaminated samples of various glove box materials burning in or exposed to the flames of the standardized 0.6 MW fire source previously developed. Beyond spreading of the Ce-Eu-oxide powder as mentioned above, the other important surface contamination process is used, i.e. deposition and subsequent drying of droplets from acid cerium-europium solutions. It is shown that, among the tested materials, and with the exception of synthetic glove rubber, burning PMMA spreads the most radioactive contamination. On the other hand, this potential risk is much lower for fires involving materials contaminated from solution deposition than from powder or pellets. Attempts to measure the airborne contaminant particle sizes did not yield conclusive results. They suggest, however, that contamination from solutions leads to smaller heavy-metal containing aerosol particles than contamination with powder

  12. Charged NUT field : [Part] I. Motion of test particles and [Part] II. Cosmic censorship

    International Nuclear Information System (INIS)

    Krori, K.D.

    1981-01-01

    Some properties of the charged NUT field are studied. In the first part of the paper, some general aspects of the charged NUT field have been investigated using uncharged and charged particles. The behaviour of the particles near the singularity has also been considered. In the second part of the paper, the charged NUT sources in the context of cosmic censorship hypothesis are studied. Motion of charged particles in the equatorial plane and along the axis is considered. From this investigation the interesting result is discovered that by such a bombardment of charged test particles, the existing event horizons cannot be destroyed but, in contrast to the Reissner-Nordstrom field, naked singularities do not get enveloped by event horizons. (author)

  13. Three decades (1983-2010) of contaminant trends in East Greenland polar bears (Ursus maritimus). Part 1: legacy organochlorine contaminants.

    Science.gov (United States)

    Dietz, Rune; Rigét, Frank F; Sonne, Christian; Born, Erik W; Bechshøft, Thea; McKinney, Melissa A; Letcher, Robert J

    2013-09-01

    Legacy organochlorine contaminants were determined in adipose tissues from 294 polar bears (Ursus maritimus) sampled in East Greenland in 23 of the 28years between 1983 and 2010. Of 19 major legacy contaminants and congeners (ΣPCB, 4 PCB congeners (CB153, 180, 170/190), ΣDDT, p,p'-DDE, p,p' -DDD and p,p'-DDT, α- and β-hexachlorocyclohexane (HCH), HCB, octachlorostyrene, dieldrin, oxychlordane, cis- and trans-chlordane, cis- and trans-nonachlor, heptachlor epoxide and BB-153), 18 showed statistically significant average yearly declines of -4.4% (range: -2.0 to -10.8%/year) among subadult polar bears (i.e. femalespolar bear tissues. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Validating the standard for the National Board Dental Examination Part II.

    Science.gov (United States)

    Tsai, Tsung-Hsun; Neumann, Laura M; Littlefield, John H

    2012-05-01

    As part of the overall exam validation process, the Joint Commission on National Dental Examinations periodically reviews and validates the pass/fail standard for the National Board Dental Examination (NBDE), Parts I and II. The most recent standard-setting activities for NBDE Part II used the Objective Standard Setting method. This report describes the process used to set the pass/fail standard for the 2009 exam. The failure rate on the NBDE Part II increased from 5.3 percent in 2008 to 13.7 percent in 2009 and then decreased to 10 percent in 2010. This article describes the Objective Standard Setting method and presents the estimated probabilities of classification errors based on the beta binomial mathematical model. The results show that the probability of correct classifications of candidate performance is very high (0.97) and that probabilities of false negative and false positive errors are very small (.03 and <0.001, respectively). The low probability of classification errors supports the conclusion that the pass/fail score on the NBDE Part II is a valid guide for making decisions about candidates for dental licensure.

  15. Understanding Medicines: Conceptual Analysis of Nurses' Needs for Knowledge and Understanding of Pharmacology (Part I). Understanding Medicines: Extending Pharmacology Education for Dependent and Independent Prescribing (Part II).

    Science.gov (United States)

    Leathard, Helen L.

    2001-01-01

    Part I reviews what nurses need to know about the administration and prescription of medicines. Part II addresses drug classifications, actions and effects, and interactions. Also discussed are the challenges pharmacological issues pose for nursing education. (SK)

  16. Arterial supply and venous drainage of the brain of the black bear (Ursus americanus). II.Intracranial microvasculature

    NARCIS (Netherlands)

    Anderson, B.G.; Anderson, W.D.; Seguin, R.J.

    1989-01-01

    A morphological study of the intracranial microvasculature of the Black bear (Ursus americanus) using vascular casts was undertaken. The object was to provide basic information regarding structural modifications of the microvasculature that might provide insight into the ability to cope with low

  17. Bearing structures

    International Nuclear Information System (INIS)

    Lee, A.S.; Preece, G.E.

    1988-01-01

    A hydrostatic bearing for the lower end of the vertical shaft of a sodium pump comprises a support shell encircling the shaft and a bush located between the shell and shaft. Liquid sodium is fed from the pump outlet to the bush/shaft and bush/shell interfaces to provide hydrostatic support. The bush outer surface and the shell inner surface are of complementary part-spherical shape and the bush floats relative to the shaft so that the bush can align itself with the shaft axis. Monitoring of the relative rotational speed of the bush with respect to the shaft (such rotation being induced by the viscous drag forces present) is also performed for the purposes of detecting abnormal operation of the bearing or partial seizure, at least one magnet is rotatable with the bush, and a magnetic sensor provides an output having a frequency related to the speed of the bush. (author)

  18. Bearing system

    Science.gov (United States)

    Kapich, Davorin D.

    1987-01-01

    A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

  19. 78 FR 45912 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Science.gov (United States)

    2013-07-30

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-570-601] Tapered Roller Bearings and..., International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue NW... Duty New Shipper Review AGENCY: Import Administration, International Trade Administration, Department...

  20. 76 FR 52937 - Ball Bearings and Parts Thereof From France, Germany, and Italy: Final Results of Antidumping...

    Science.gov (United States)

    2011-08-24

    ... programming and other errors in the margin calculations. Therefore, the final results are different from the... certain companies. We have corrected programming and other errors in the margins we included in the... Technologies GmbH; Italy--Schaeffler Italia S.r.l./WPB Water Pump Bearing GmbH & Co. KG/The Schaeffler Group...

  1. Ocean Thermal Energy Converstion (OTEC) test facilities study program. Final report. Volume II. Part B

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-01-17

    Results are presented of an 8-month study to develop alternative non-site-specific OTEC facilities/platform requirements for an integrated OTEC test program which may include land and floating test facilities. Volume II--Appendixes is bound in three parts (A, B, and C) which together comprise a compendium of the most significant detailed data developed during the study. Part B provides an annotated test list and describes component tests and system tests.

  2. Starting a hospital-based home health agency: Part II--Key success factors.

    Science.gov (United States)

    Montgomery, P

    1993-09-01

    In Part II of a three-part series, the financial, technological and legislative issues of a hospital-based home health-agency are discussed. Beginning a home healthcare service requires intensive research to answer key environmental and operational questions--need, competition, financial projections, initial start-up costs and the impact of delayed depreciation. Assessments involving technology, staffing, legislative and regulatory issues can help project service volume, productivity and cost-control.

  3. Title II, Part A: Don't Scrap It, Don't Dilute It, Fix It

    Science.gov (United States)

    Coggshall, Jane G.

    2015-01-01

    The Issue: Washington is taking a close look at Title II, Part A (Title IIA) of the Elementary and Secondary Education Act (ESEA) as Congress debates reauthorization. The program sends roughly $2.5 billion a year to all states and nearly all districts to "(1) increase student academic achievement through strategies such as improving teacher…

  4. Instructional Climates in Preschool Children Who Are At-Risk. Part II: Perceived Physical Competence

    Science.gov (United States)

    Robinson, Leah E.; Rudisill, Mary E.; Goodway, Jacqueline D.

    2009-01-01

    In Part II of this study, we examined the effect of two 9-week instructional climates (low-autonomy [LA] and mastery motivational climate [MMC]) on perceived physical competence (PPC) in preschoolers (N = 117). Participants were randomly assigned to an LA, MMC, or comparison group. PPC was assessed by a pretest, posttest, and retention test with…

  5. Failure analysis of motor bearing of sea water pump in nuclear power plant

    International Nuclear Information System (INIS)

    Bian Chunhua; Zhang Wei

    2015-01-01

    The motor bearing of sea water pump in Qinshan Phase II Nuclear Power plant broke after only one year's using. This paper introduces failure analysis process of the motor bearing. Chemical composition analysis, metallic phase analysis, micrographic examination, and hardness analysis, dimension analysis of each part of the bearing, as well as the high temperature and low temperature performance analysis of lubricating grease are performed. According to the analysis above mentioned, the failure mode of the bearing is wearing, and the reason of wearing is inappropriate installation of the bearing. (authors)

  6. High energy physics studies. Progress report. Part I. Experimental program. Part II. Theoretical program

    International Nuclear Information System (INIS)

    Romanowski, T.A.; Tanaka, K.; Wada, W.W.

    1978-01-01

    Experimental Program: assembly of an experiment as Fermilab E-531 to measure decay lifetimes, with tagged emulsion of charmed particles produced by high energy neutrinos was finished, and data taking now is in progress. An experiment to measure prompt neutrino production at Fermilab, E-613, was approved and detailed design of it is continuing. Search for parity violation in scattering of polarized protons, an experiment E-446-ZGS at ANL, was performed with the sensitivity of 10 -6 for detection of that process and yielded null results. Another run with improved sensitivity of 10 -7 is in preparation. Data analysis of the neutrino experiment E-310 at Fermilab will continue. Trimuon events, a new discovery, were identified in those data. Analysis of data on meson production from experiments performed at the ZGS--ANL, E-397, E-420 and E-428, with charged and neutral spectrometer will continue. A new relatively broad resonance (T approx. 70 MeV) with quantum numbers IJ/sup P/ = 00 -1 was discovered in the data from E-397. Analysis of beta decay of polarized Σ - hyperons is in progress. Participation in the design of the experimental areas for the Isabelle colliding proton beam accelerator will continue. Theoretical Program: topics of current interest in particle theory which will be investigated in the coming year are: the instanton-anti-instanton QCD gauge fields, discrete symmetries which may determine quark masses in the SU(2) x U(1) model, calculation of charmed meson production in e + e - collisions and formation of gluon jets, Higgs boson production in pp collisions, calculation of Higgs boson mass in terms of vector boson mass, study of Lagrangians with gauge and Higgs scalar fields, investigation of Faddeev--Popov determinants as related to quantum chromodynamics, a study of quantum flavor dynamics and anomalies in the axial vector Ward identity and a study of super symmetry as a part of a realistic model of leptonic interactions

  7. Subseabed disposal program annual report, January-December 1979. Volume II. Appendices (principal investigator progress reports). Part 2 of 2

    International Nuclear Information System (INIS)

    Talbert, D.M.

    1981-04-01

    Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume II, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-O; Part 2 contains Appendices P-FF. Separate abstracts have been prepared for each appendix for inclusion in the Energy Data Base

  8. Novel zinc(II)phthalocyanines bearing azo-containing schiff base: Determination of pKa values, absorption, emission, enzyme inhibition and photochemical properties

    Science.gov (United States)

    Kantar, Cihan; Mavi, Vildan; Baltaş, Nimet; İslamoğlu, Fatih; Şaşmaz, Selami

    2016-10-01

    Azo-containing schiff bases are well known and there are many studies about their various properties in literature. However, phthalocyanines bearing azo-containing schiff bases, their spectral, analytical and biological properties are unknown. Therefore, new zinc (II) phthalocyanines bearing azo-containing schiff base were synthesized and investigated to determine pKa values, absorption, emission, enzyme inhibition and photochemical properties. Emission spectra were reported and large Stokes shift values were determined for all compounds, indicating that all molecules exhibit excited state intramolecular proton transfer. These phthalocyanines were the first examples of phthalocyanine showing excited state intramolecular proton transfer. Singlet oxygen quantum yields of zinc (II) phthalocyanines were determined. pKa values and indicator properties of all compounds were investigated by potentiometry. All compounds were assayed for inhibitory activity against bovine milk xanthine oxidase and acetylcholinesterase enzyme in vitro. Compound 2 showed the high inhibitory effect against xanthine oxidase (IC50 = 0.24 ± 0.01 μM). However, phthalocyanine compounds did not show enzyme inhibitor behavior.

  9. A Type II Arabinogalactan from Anoectochilus formosanus for G-CSF Production in Macrophages and Leukopenia Improvement in CT26-Bearing Mice Treated with 5-Fluorouracil.

    Science.gov (United States)

    Yang, Li-Chan; Lu, Ting-Jang; Lin, Wen-Chuan

    2013-01-01

    Anoectochilus formosanus is an herb well known in Asian countries. The polysaccharide isolated from A. formosanus consists of type II arabinogalactan (AGAF), with branched 3,6-Gal as the major moiety. In this study, AGAF was examined for the granulocyte colony-stimulating factor (G-CSF) production and related protein expression in RAW 264.7 murine macrophages. The signaling pathway of G-CSF production involves AGAF and mitogen-activated protein kinases (MAPKs) inhibitors and pattern-recognition receptor antibodies. AGAF was evaluated to ease the leukopenia in CT26-colon-cancer-bearing mice treated with 5-fluorouracil (5-FU). The results of this study showed that AGAF was a stimulant for Toll-like receptor 2 and Dectin-1 and that it induced G-CSF production, through p38 and ERK MAPK, and NF- κ B pathways. In vivo examination showed that the oral administration of AGAF mitigated the side effects of leukopenia caused by 5-FU in colon-cancer-bearing mice. In conclusion, the botanic type II AGAF in this study was a potent G-CSF inducer in vivo and in vitro.

  10. A Type II Arabinogalactan from Anoectochilus formosanus for G-CSF Production in Macrophages and Leukopenia Improvement in CT26-Bearing Mice Treated with 5-Fluorouracil

    Directory of Open Access Journals (Sweden)

    Li-Chan Yang

    2013-01-01

    Full Text Available Anoectochilus formosanus is an herb well known in Asian countries. The polysaccharide isolated from A. formosanus consists of type II arabinogalactan (AGAF, with branched 3,6-Gal as the major moiety. In this study, AGAF was examined for the granulocyte colony-stimulating factor (G-CSF production and related protein expression in RAW 264.7 murine macrophages. The signaling pathway of G-CSF production involves AGAF and mitogen-activated protein kinases (MAPKs inhibitors and pattern-recognition receptor antibodies. AGAF was evaluated to ease the leukopenia in CT26-colon-cancer-bearing mice treated with 5-fluorouracil (5-FU. The results of this study showed that AGAF was a stimulant for Toll-like receptor 2 and Dectin-1 and that it induced G-CSF production, through p38 and ERK MAPK, and NF-κB pathways. In vivo examination showed that the oral administration of AGAF mitigated the side effects of leukopenia caused by 5-FU in colon-cancer-bearing mice. In conclusion, the botanic type II AGAF in this study was a potent G-CSF inducer in vivo and in vitro.

  11. Three decades (1983-2010) of contaminant trends in East Greenland polar bears (Ursus maritimus). Part 2

    DEFF Research Database (Denmark)

    Dietz, Rune; Rigét, Frank F; Sonne, Christian

    2013-01-01

    Legacy organochlorine contaminants were determined in adipose tissues from 294 polar bears (Ursus maritimus) sampled in East Greenland in 23 of the 28years between 1983 and 2010. Of 19 major legacy contaminants and congeners (ΣPCB, 4 PCB congeners (CB153, 180, 170/190), ΣDDT, p,p'-DDE, p,p' -DDD...... and p,p'-DDT, α- and β-hexachlorocyclohexane (HCH), HCB, octachlorostyrene, dieldrin, oxychlordane, cis- and trans-chlordane, cis- and trans-nonachlor, heptachlor epoxide and BB-153), 18 showed statistically significant average yearly declines of -4.4% (range: -2.0 to -10.8%/year) among subadult polar...... bears (i.e. females...

  12. Three decades (1983-2010) of contaminant trends in East Greenland polar bears (Ursus maritimus). Part 2: brominated flame retardants.

    Science.gov (United States)

    Dietz, Rune; Rigét, Frank F; Sonne, Christian; Born, Erik W; Bechshøft, Thea; McKinney, Melissa A; Drimmie, Robert J; Muir, Derek C G; Letcher, Robert J

    2013-09-01

    Brominated flame retardants were determined in adipose tissues from 294 polar bears (Ursus maritimus) sampled in East Greenland in 23 of the 28years between 1983 and 2010. Significant linear increases were found for sum polybrominated diphenyl ether (ΣPBDE), BDE100, BDE153, and hexabromocyclododecane (HBCD). Average increases of 5.0% per year (range: 2.9-7.6%/year) were found for the subadult polar bears. BDE47 and BDE99 concentrations did not show a significant linear trend over time, but rather a significant non-linear trend peaking between 2000 and 2004. The average ΣPBDE concentrations increased 2.3 fold from 25.0ng/g lw (95% C.I.: 15.3-34.7ng/g lw) in 1983-1986 to 58.5ng/g lw (95% C.I.: 43.6-73.4ng/g lw) in 2006-2010. Similar but fewer statistically significant trends were found for adult females and adult males likely due to smaller sample size and years. Analyses of δ(15)N and δ(13)C stable isotopes in hair revealed no clear linear temporal trends in trophic level or carbon source, respectively, and non-linear trends differed among sex and age groups. These increasing concentrations of organobromine contaminants contribute to complex organohalogen mixture, already causing health effects to the East Greenland polar bears. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. Synthesis and characterization of Ni(II, Cu(II and Co(III complexes with polyamine-containing macrocycles bearing an aminoethyl pendant arm

    Directory of Open Access Journals (Sweden)

    K. S. SIDDIQI

    2004-09-01

    Full Text Available Reaction of [M(ppn2]X2 (where M = Cu(II, Ni(II, Co(II and ppn = 1,3-diaminopropane with formaldehyde and ethylenediamine in methanol results in the ready formation of a 16-membered macrocyclic complex. The complexes were characterized by elemental anlysis, IR, EPR, electronic spectral data, magnetic moments and conductance measurements. The Cu(II, Ni(II and Co(III complexes are coordinated axially with both pendant groups of the hexadentate macrocycle. These pendant donors are attached to the macrocycle by a carbon chain. The electrical conductivities of the Cu(II and Ni(II chelates indicated them to be 1:2 electrolytes whilst those of Co(III is a 1:3 electrolyte in DMSO. The EPR spectrum of the copper complex exhibited G at 3.66, which indicates a considerable exchange interaction in the complex. Spectroscopic evidence suggests that in all of the complexes the metal ion is in an octahedral environment.

  14. Surface-initiated addition polymerization of norbornene by a Pd(II) catalyst bearing acetylacetone ligand on the glass slide

    Science.gov (United States)

    He, Xiaohui; Wang, Kaiti; Chen, Yiwang; Yuan, Bin

    2012-02-01

    A Pd catalyst bearing acetylacetone ligand [(CH3CO)2CHPdCl2] was covalently attracted onto the surface of glass slides, and then these Pd-terminated glass slides were immersed into a toluene solution of norbornene (NB) to produce a vinyl-type addition polynorbornene (PNB) layer on the surface of glass slides. It was found that the contract angles of the PNB-terminated glass slides surface increased with the increasing of polymerization time, and the thickness of the PNB layers were approximately 0-44.0 μm when the polymerization time was 0.5-24 h. The researching on etching also has been operated.

  15. Bloqueio do nervo supraescapular: procedimento importante na prática clínica. Parte II Suprascapular nerve block: important procedure in clinical practice. Part II

    Directory of Open Access Journals (Sweden)

    Marcos Rassi Fernandes

    2012-08-01

    Full Text Available O bloqueio do nervo supraescapular é um método de tratamento reprodutível, confiável e extremamente efetivo no controle da dor no ombro. Esse método tem sido amplamente utilizado por profissionais na prática clínica, como reumatologistas, ortopedistas, neurologistas e especialistas em dor, na terapêutica de enfermidades crônicas, como lesão irreparável do manguito rotador, artrite reumatoide, sequelas de AVC e capsulite adesiva, o que justifica a presente revisão (Parte II. O objetivo deste estudo foi descrever as técnicas do procedimento e suas complicações descritas na literatura, já que a primeira parte reportou as indicações clínicas, drogas e volumes utilizados em aplicação única ou múltipla. Apresentamse, detalhadamente, os acessos para a realização do procedimento tanto direto como indireto, anterior e posterior, lateral e medial, e superior e inferior. Diversas são as opções para se realizar o bloqueio do nervo supraescapular. Apesar de raras, as complicações podem ocorrer. Quando bem indicado, este método deve ser considerado.The suprascapular nerve block is a reproducible, reliable, and extremely effective treatment method in shoulder pain control. This method has been widely used by professionals in clinical practice such as rheumatologists, orthopedists, neurologists, and pain specialists in the treatment of chronic diseases such as irreparable rotator cuff injury, rheumatoid arthritis, stroke sequelae, and adhesive capsulitis, which justifies the present review (Part II. The objective of this study was to describe the techniques and complications of the procedure described in the literature, as the first part reported the clinical indications, drugs, and volumes used in single or multiple procedures. We present in details the accesses used in the procedure: direct and indirect, anterior and posterior, lateral and medial, upper and lower. There are several options to perform suprascapular nerve block

  16. Societal Planning: Identifying a New Role for the Transport Planner-Part II: Planning Guidelines

    DEFF Research Database (Denmark)

    Khisty, C. Jotin; Leleur, Steen

    1997-01-01

    The paper seeks to formulate planning guidelines based on Habermas's theory of communicative action. Specifically, this has led to the formulation of a set of four planning validity claims concerned to four types of planning guidelines concerning adequacy, dependency, suitability and adaptability......-a-vis the planning validity claims. Among other things the contingency of this process is outlined. It is concluded (part I & II) that transport planners can conveniently utilize the guidelines in their professional practice, tailored to their particular settings....

  17. Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part II

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-07-01

    The Summary Report - Part II of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors - includes reports on development of fast reactors in France from 1977 to 1978; review of the activities related to fast reactors in Germany; status of fast breeder reactors development in Belgium and Netherlands; status of activities related to fast reactors in USSR, Japan USA, UK and Italy.

  18. The basic science of dermal fillers: past and present Part II: adverse effects.

    Science.gov (United States)

    Gilbert, Erin; Hui, Andrea; Meehan, Shane; Waldorf, Heidi A

    2012-09-01

    The ideal dermal filler should offer long-lasting aesthetic improvement with a minimal side-effect profile. It should be biocompatible and stable within the injection site, with the risk of only transient undesirable effects from injection alone. However, all dermal fillers can induce serious and potentially long-lasting adverse effects. In Part II of this paper, we review the most common adverse effects related to dermal filler use.

  19. Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part II

    International Nuclear Information System (INIS)

    1978-07-01

    The Summary Report - Part II of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors - includes reports on development of fast reactors in France from 1977 to 1978; review of the activities related to fast reactors in Germany; status of fast breeder reactors development in Belgium and Netherlands; status of activities related to fast reactors in USSR, Japan USA, UK and Italy

  20. A thermoelectric power generating heat exchanger: Part II – Numerical modeling and optimization

    DEFF Research Database (Denmark)

    Sarhadi, Ali; Bjørk, Rasmus; Lindeburg, N.

    2016-01-01

    In Part I of this study, the performance of an experimental integrated thermoelectric generator (TEG)-heat exchanger was presented. In the current study, Part II, the obtained experimental results are compared with those predicted by a finite element (FE) model. In the simulation of the integrated...... TEG-heat exchanger, the thermal contact resistance between the TEG and the heat exchanger is modeled assuming either an ideal thermal contact or using a combined Cooper–Mikic–Yovanovich (CMY) and parallel plate gap formulation, which takes into account the contact pressure, roughness and hardness...

  1. Quantitative impact of aerosols on numerical weather prediction. Part II: Impacts to IR radiance assimilation

    Science.gov (United States)

    Marquis, J. W.; Campbell, J. R.; Oyola, M. I.; Ruston, B. C.; Zhang, J.

    2017-12-01

    This is part II of a two-part series examining the impacts of aerosol particles on weather forecasts. In this study, the aerosol indirect effects on weather forecasts are explored by examining the temperature and moisture analysis associated with assimilating dust contaminated hyperspectral infrared radiances. The dust induced temperature and moisture biases are quantified for different aerosol vertical distribution and loading scenarios. The overall impacts of dust contamination on temperature and moisture forecasts are quantified over the west coast of Africa, with the assistance of aerosol retrievals from AERONET, MPL, and CALIOP. At last, methods for improving hyperspectral infrared data assimilation in dust contaminated regions are proposed.

  2. The year 2013 in the European Heart Journal--Cardiovascular Imaging: Part II.

    Science.gov (United States)

    Plein, Sven; Edvardsen, Thor; Pierard, Luc A; Saraste, Antti; Knuuti, Juhani; Maurer, Gerald; Lancellotti, Patrizio

    2014-08-01

    The new multi-modality cardiovascular imaging journal, European Heart Journal - Cardiovascular Imaging, was created in 2012. Here we summarize the most important studies from the journal's second year in two articles. Part I of the review has summarized studies in myocardial function, myocardial ischaemia, and emerging techniques in cardiovascular imaging. Part II is focussed on valvular heart diseases, heart failure, cardiomyopathies, and congenital heart diseases. Published on behalf of the European Society of Cardiology. All rights reserved. © The Author 2014. For permissions please email: journals.permissions@oup.com.

  3. 40 CFR Appendix III to Part 266 - Tier II Emission Rate Screening Limits for Free Chlorine and Hydrogen Chloride

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Tier II Emission Rate Screening Limits for Free Chlorine and Hydrogen Chloride III Appendix III to Part 266 Protection of Environment... to Part 266—Tier II Emission Rate Screening Limits for Free Chlorine and Hydrogen Chloride Terrain...

  4. Field Surveys, IOC Valleys. Volume III, Part II. Cultural Resources Survey, Pine and Wah Wah Valleys, Utah.

    Science.gov (United States)

    1981-08-01

    including horse, camel, mammoth, Ertm E-TR-48-III-II 20 musk ox, and certain species of bison, goat, and bear, which had previously inhabited the marsh and...34 - - -9,$.. 𔄃 Im I I I Si to * Location lype/Contents Affiliation 42B@644 rid e over cr ek - P/J depression, cleared areas, Fr elon (f4-5-18-92) ground

  5. Estrogen receptor binding radiopharmaceuticals: II. Tissue distribution of 17 α-methylestradiol in normal and tumor-bearing rats

    International Nuclear Information System (INIS)

    Feenstra, A.; Vaalburg, W.; Nolten, G.M.J.; Reiffers, S.; Talma, A.G.; Wiegman, T.; van der Molen, H.D.; Woldring, M.G.

    1983-01-01

    Tritiated 17α-methylestradiol was synthesized to investigate the potential of the carbon-11-labeled analog as an estrogen-receptor-binding radiopharmaceutical. In vitro, 17α-methylestradiol is bound with high affinity to the cytoplasmic estrogen receptor from rabbit uterus (K/sub d/ = 1.96 x 10 -10 M), and it sediments as an 8S hormone-receptor complex in sucrose gradients. The compound shows specific uptake in the uterus of the adult rat, within 1 h after injection. In female rats bearing DMBA-induced tumors, specific uterine and tumor uptakes were observed, although at 30 min the tumor uptake was only 23 to 30% of the uptake in the uterus. Tritiated 17α-methylestradiol with a specific activity of 6 Ci/mmole showed a similar tissue distribution. Our results indicate that a 17 α-methylestradiol is promising as an estrogen-receptor-binding radiopharmaceutical

  6. Best management practices plan for Phase II of the Bear Creek Valley treatability study, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1997-09-01

    The Oak Ridge Y-12 Plant is currently under a Federal Agreement to define soil and groundwater contamination and develop remedies to protect human health and the environment. The western end of the site is known to have a former nitric acid disposal pit that has been remediated and capped. Remedial investigation data indicate this pit was a source of nitrate, uranium, technetium, and other metals contamination in groundwater. The downgradient receptor of this contamination includes Bear Creek and its tributaries. A feasibility study is under way to develop a remedy to prevent further contaminant migration to this receptor. To support the feasibility study, the treatability study is being completed to examine groundwater treatment at the S-3 site. This document serves as the top-level command medium for Phase II of the Bear Creek Valley (BCV) Treatability Study and, as such, will be the primary resource for management and implementation of field activities. Many of the details and standard operating procedures referred to herein can be found in other Lockheed Martin Energy Systems, Inc. (Energy Systems), documents. Several supporting documents specific to this project are also cited. These include the Sampling and Analysis Plan (SAP), the Health and Safety Plan (HASP), and the Waste Management Plan (WMP)

  7. 78 FR 76104 - Ball Bearings and Parts Thereof From Japan and the United Kingdom: Notice of Reinstatement of...

    Science.gov (United States)

    2013-12-16

    ...On July 15, 2011, pursuant to a decision of the Court of International Trade (CIT) that affirmed the International Trade Commission's (ITC's) negative injury determinations on remand in the second sunset review of the antidumping duty orders on bearings from Japan and the United Kingdom, the Department of Commerce (the Department) revoked the Orders.\\1\\ On May 16, 2013, the United States Court of Appeals for the Federal Circuit (Federal Circuit) reversed the CIT's decision and ordered the CIT to reinstate the ITC's affirmative material injury determinations.\\2\\ Subsequently, on November 18, 2013, the CIT issued final judgment reinstating the ITC's affirmative injury determinations.\\3\\ Therefore, the Department is now reinstating the Orders. Additionally, the Department is resuming the administrative reviews of these orders for the periods May 1, 2009, through April 30, 2010, and May 1, 2010, through April 30, 2011. ---------------------------------------------------------------------------

  8. Synthesis of 3-(4,5-dihydroimidazol-1-YL)propyltriethoxysilane bound Ru(II) complex bearing viologen segment

    International Nuclear Information System (INIS)

    Gurbuz, N.; Seckin, T.; Ozdemir, I.; Cetinkaya, B.

    2005-01-01

    The nanostructured metallopolymers consisting of the partially quaternized 3-(4,5-dihydroimidazol-1-yl)propyl having the viologen group linked covalently through the alkyl spacer its Ru(II) complex have been prepared by sol-gel method. Structural elucidation was done with Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and differential thermal analysis (DTA) [ru

  9. Part I: quantum fluctuations in chains of Josephson junctions. Part II: directed aggregation on the Bethe lattice

    International Nuclear Information System (INIS)

    Bradley, R.M.

    1985-01-01

    Part I studies the effect of quantum fluctuations of the phase on the low temperature behavior of two models of Josephson junction chains with Coulomb interactions taken into account. The first model, which represents a chain of junctions close to a ground plane, is the Hamiltonian version of the two-dimensional XY model in one space and one time dimension. In the second model, the charging energy for a single junction in the chain is just the parallel-plate capacitor energy. It is shown that quantum fluctuations produce exponential decay of the order parameter correlation junction for any finite value of the junction capacitance. Part II deals with two types of directed aggregation on the Bethe lattice - directed diffusion-limited aggregation DDLA and ballistic aggregation (BA). In the DDLA problem on finite lattices, an exact nonlinear recursion relation is constructed for the probability distribution of the density. The mean density tends to zero as the lattice size is taken into infinity. Using a mapping between the model with perfect adhesion on contact and another model with a particular value of the adhesion probability, it is shown that the adhesion probability is irrelevant over an interval of values

  10. Scope Oriented Thermoeconomic analysis of energy systems. Part II: Formation Structure of Optimality for robust design

    International Nuclear Information System (INIS)

    Piacentino, Antonio; Cardona, Ennio

    2010-01-01

    This paper represents the Part II of a paper in two parts. In Part I the fundamentals of Scope Oriented Thermoeconomics have been introduced, showing a scarce potential for the cost accounting of existing plants; in this Part II the same concepts are applied to the optimization of a small set of design variables for a vapour compression chiller. The method overcomes the limit of most conventional optimization techniques, which are usually based on hermetic algorithms not enabling the energy analyst to recognize all the margins for improvement. The Scope Oriented Thermoeconomic optimization allows us to disassemble the optimization process, thus recognizing the Formation Structure of Optimality, i.e. the specific influence of any thermodynamic and economic parameter in the path toward the optimal design. Finally, the potential applications of such an in-depth understanding of the inner driving forces of the optimization are discussed in the paper, with a particular focus on the sensitivity analysis to the variation of energy and capital costs and on the actual operation-oriented design.

  11. A legacy of struggle: the OSHA ergonomics standard and beyond, Part II.

    Science.gov (United States)

    Delp, Linda; Mojtahedi, Zahra; Sheikh, Hina; Lemus, Jackie

    2014-11-01

    The OSHA ergonomics standard issued in 2000 was repealed within four months through a Congressional resolution that limits future ergonomics rulemaking. This section continues the conversation initiated in Part I, documenting a legacy of struggle for an ergonomics standard through the voices of eight labor, academic, and government key informants. Part I summarized important components of the standard; described the convergence of labor activism, research, and government action that laid the foundation for a standard; and highlighted the debates that characterized the rulemaking process. Part II explores the anti-regulatory political landscape of the 1990s, as well as the key opponents, power dynamics, and legal maneuvers that led to repeal of the standard. This section also describes the impact of the ergonomics struggle beyond the standard itself and ends with a discussion of creative state-level policy initiatives and coalition approaches to prevent work-related musculoskeletal disorders (WMSDs) in today's sociopolitical context.

  12. Subseabed disposal program annual report, January-December 1979. Volume II. Appendices (principal investigator progress reports). Part 1 of 2

    International Nuclear Information System (INIS)

    Talbert, D.M.

    1981-04-01

    Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume I, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-O; Part 2 contains Appendices P-FF. Separate abstracts have been prepared of each Appendix for inclusion in the Energy Data Base

  13. Subseabed disposal program annual report, January-December 1980. Volume II. Appendices (principal investigator progress reports). Part 1

    Energy Technology Data Exchange (ETDEWEB)

    Hinga, K.R. (ed.)

    1981-07-01

    Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume I, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-Q; Part 2 contains Appendices R-MM. Separate abstracts have been prepared for each appendix for inclusion in the Energy Data Base.

  14. Subseabed disposal program annual report, January-December 1980. Volume II. Appendices (principal investigator progress reports). Part 1

    International Nuclear Information System (INIS)

    Hinga, K.R.

    1981-07-01

    Volume II of the sixth annual report describing the progress and evaluating the status of the Subseabed Disposal Program contains the appendices referred to in Volume I, Summary and Status. Because of the length of Volume II, it has been split into two parts for publication purposes. Part 1 contains Appendices A-Q; Part 2 contains Appendices R-MM. Separate abstracts have been prepared for each appendix for inclusion in the Energy Data Base

  15. Formulation, computation and improvement of steady state security margins in power systems. Part II: Results

    International Nuclear Information System (INIS)

    Echavarren, F.M.; Lobato, E.; Rouco, L.; Gomez, T.

    2011-01-01

    A steady state security margin for a particular operating point can be defined as the distance from this initial point to the secure operating limits of the system. Four of the most used steady state security margins are the power flow feasibility margin, the contingency feasibility margin, the load margin to voltage collapse, and the total transfer capability between system areas. This is the second part of a two part paper. Part I has proposed a novel framework of a general model able to formulate, compute and improve any steady state security margin. In Part II the performance of the general model is validated by solving a variety of practical situations in modern real power systems. Actual examples of the Spanish power system will be used for this purpose. The same computation and improvement algorithms outlined in Part I have been applied for the four security margins considered in the study, outlining the convenience of defining a general framework valid for the four of them. The general model is used here in Part II to compute and improve: (a) the power flow feasibility margin (assessing the influence of the reactive power generation limits in the Spanish power system), (b) the contingency feasibility margin (assessing the influence of transmission and generation capacity in maintaining a correct voltage profile), (c) the load margin to voltage collapse (assessing the location and quantity of loads that must be shed in order to be far away from voltage collapse) and (d) the total transfer capability (assessing the export import pattern of electric power between different areas of the Spanish system). (author)

  16. Formulation, computation and improvement of steady state security margins in power systems. Part II: Results

    Energy Technology Data Exchange (ETDEWEB)

    Echavarren, F.M.; Lobato, E.; Rouco, L.; Gomez, T. [School of Engineering of Universidad Pontificia Comillas, C/Alberto Aguilera, 23, 28015 Madrid (Spain)

    2011-02-15

    A steady state security margin for a particular operating point can be defined as the distance from this initial point to the secure operating limits of the system. Four of the most used steady state security margins are the power flow feasibility margin, the contingency feasibility margin, the load margin to voltage collapse, and the total transfer capability between system areas. This is the second part of a two part paper. Part I has proposed a novel framework of a general model able to formulate, compute and improve any steady state security margin. In Part II the performance of the general model is validated by solving a variety of practical situations in modern real power systems. Actual examples of the Spanish power system will be used for this purpose. The same computation and improvement algorithms outlined in Part I have been applied for the four security margins considered in the study, outlining the convenience of defining a general framework valid for the four of them. The general model is used here in Part II to compute and improve: (a) the power flow feasibility margin (assessing the influence of the reactive power generation limits in the Spanish power system), (b) the contingency feasibility margin (assessing the influence of transmission and generation capacity in maintaining a correct voltage profile), (c) the load margin to voltage collapse (assessing the location and quantity of loads that must be shed in order to be far away from voltage collapse) and (d) the total transfer capability (assessing the export import pattern of electric power between different areas of the Spanish system). (author)

  17. Three Mile Island: a report to the commissioners and to the public. Volume II, Part 1

    International Nuclear Information System (INIS)

    1979-01-01

    This is part one of three parts of the second volume of the Special Inquiry Group's report to the Nuclear Regulatory Commission on the accident at Three Mile Island. The first volume contained a narrative description of the accident and a discussion of the major conclusions and recommendations. This second volume is divided into three parts. Part 1 of Volume II focuses on the pre-accident licensing and regulatory background. This part includes an examination of the overall licensing and regulatory system for nuclear powerplants viewed from different perspectives: the system as it is set forth in statutes and regulations, as described in Congressional testimony, and an overview of the system as it really works. In addition, Part 1 includes the licensing, operating, and inspection history of Three Mile Island Unit 2, discussions of relevant regulatory matters, a discussion of specific precursor events related to the accident, a case study of the pressurizer design issue, and an analysis of incentives to declare commercial operation

  18. Catalytic behaviors of Co{sup II} and Mn{sup II} compounds bearing α-Diimine ligands for oxidative polymerization or drying oils

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Gilvan E.S.; Nunes, Everton V.; Dantas, Roberta C.; Meneghetti, Mario R.; Meneghetti, Simoni M.P., E-mail: simoni.plentz@gmail.com [Universidade Federal de Alagoas (UFAL), Maceió, AL (Brazil). Grupo de Catálise e Reatividade Química; Simone, Carlos A. de [Universidade de Sao Paulo (USP), São Carlos, USP, SP (Brazil). Instituto de Física

    2018-05-01

    The oxidative polymerization of linseed oil was investigated comparing the classical catalysts cobalt(II) 2-ethylhexanoate and manganese(II) 2-ethylhexanoate and their derivatives modified by the presence of chelating nitrogen ligands, i.e., 2,2’-bipyridyl, 2-(acetyl-2,6-diisopropylphenylimine)- pyridine and [N-(2,6-diisopropylphenyl)imine]acenaphthoquinone. The suitable stoichiometries between the two precursor complexes with the three ligands were determined by UV-visible spectroscopy. All complexes were characterized by infrared spectroscopy, and one complex was characterized also by X-ray diffraction. The apparent kinetic constants of oxidative polymerization of linseed oil was determined, for each catalytic system, via the periodic measurements of the oil viscosity during the oxidation reaction. The results indicated that the modifications of the classical two complexes with the chelating nitrogen ligands improved the catalytic efficiency at least to the manganese complex. (author)

  19. PIC Simulations in Low Energy Part of PIP-II Proton Linac

    Energy Technology Data Exchange (ETDEWEB)

    Romanov, Gennady

    2014-07-01

    The front end of PIP-II linac is composed of a 30 keV ion source, low energy beam transport line (LEBT), 2.1 MeV radio frequency quadrupole (RFQ), and medium energy beam transport line (MEBT). This configuration is currently being assembled at Fermilab to support a complete systems test. The front end represents the primary technical risk with PIP-II, and so this step will validate the concept and demonstrate that the hardware can meet the specified requirements. SC accelerating cavities right after MEBT require high quality and well defined beam after RFQ to avoid excessive particle losses. In this paper we will present recent progress of beam dynamic study, using CST PIC simulation code, to investigate partial neutralization effect in LEBT, halo and tail formation in RFQ, total emittance growth and beam losses along low energy part of the linac.

  20. 75 FR 69402 - Ball Bearings and Parts Thereof From France, Germany, Italy, Japan, and the United Kingdom...

    Science.gov (United States)

    2010-11-12

    ..., 2010, based on requests from interested parties, we initiated administrative reviews of the antidumping... PLC. In addition, on September 1, 2010, the Department revoked, in part, the antidumping duty order on...

  1. Synthesis, structure and catalytic activities of nickel(II) complexes bearing N4 tetradentate Schiff base ligand

    Science.gov (United States)

    Sarkar, Saikat; Nag, Sanat Kumar; Chattopadhyay, Asoke Prasun; Dey, Kamalendu; Islam, Sk. Manirul; Sarkar, Avijit; Sarkar, Sougata

    2018-05-01

    Two new nickel(II) complexes [Ni(L)Cl2] (1) and [Ni(L)(NCS)2] (2) of a neutral tetradentate mono-condensed Schiff base ligand, 3-(2-(2-aminoethylamino)ethylimino)butan-2-one oxime (L) have been synthesized and characterized using different physicochemical techniques e.g. elemental analyses, spectroscopic (IR, Electronic, NMR) methods, conductivity and molecular measurements. The crystal structure of complex (2) has been determined by using single crystal X-ray diffraction method and it suggests a distorted octahedral geometry around nickel(II) having a NiN6 coordinating atmosphere. The non-coordinated Osbnd H group on the ligand L remain engaged in H-bonding interactions with the S end of the coordinated thiocyanate moiety. These H-bonding interactions lead to Osbnd S separations of 3.132 Å and play prominent role in crystal packing. It is observed that the mononuclear units are glued together with such Osbnd H…S interactions and finally results in an 1D supramolecular sheet-like arrangement. DFT/TDDFT based theoretical calculations were also performed on the ligand and the complexes aiming at the accomplishment of idea regarding their optimized geometry, electronic transitions and the molecular energy levels. Finally the catalytic behavior of the complexes for oxidation of styrene has also been carried out. A variety of reaction conditions like the effect of solvent, effect of temperature and time as well as the effect of ratio of substrate to oxidant were thoroughly studied to judge the catalytic efficiency of the Ni(II) coordination entity.

  2. Numerical simulation of projectile impact on mild steel armour plates using LS-DYNA, Part II: Parametric studies

    OpenAIRE

    Raguraman, M; Deb, A; Gupta, NK; Kharat, DK

    2008-01-01

    In Part I of the current two-part series, a comprehensive simulation-based study of impact of Jacketed projectiles on mild steel armour plates has been presented. Using the modelling procedures developed in Part I, a number of parametric studies have been carried out for the same mild steel plates considered in Part I and reported here in Part II. The current investigation includes determination of ballistic limits of a given target plate for different projectile diameters and impact velociti...

  3. Numerical Simulation of Projectile Impact on Mild Steel Armour Platesusing LS-DYNA, Part II: Parametric Studies

    OpenAIRE

    M. Raguraman; A. Deb; N. K. Gupta; D. K. Kharat

    2008-01-01

    In Part I of the current two-part series, a comprehensive simulation-based study of impact of jacketed projectiles on mild steel armour plates has been presented. Using the modelling procedures developed in Part I, a number of parametric studies have been carried out for the same mild steel plates considered in Part I and reported here in Part II. The current investigation includes determination of ballistic limits of a given target plate for different projectile diameters and impact velociti...

  4. Radiation protection instruments based on tissue equivalent proportional counters: Part II of an international intercomparison

    International Nuclear Information System (INIS)

    Alberts, W.G.; Dietz, E.; Guldbakke, S.; Kluge, H.; Schumacher, H.

    1988-04-01

    This report describes the irradiation conditions and procedures of Part II of an international intercomparison of tissue-equivalent proportional counters used for radiation protection measurements. The irradiations took place in monoenergetic reference neutron fields produced by the research reactor and accelerator facilities of the PTB Braunschweig in the range from thermal neutrons to 14.8 MeV. In addition measurements were performed in 60 Co and D 2 O-moderated 252 Cf radiation fields. Prototype instruments from 7 European groups were investigated. The results of the measurements are summarized and compared with the reference data of the irradiations. (orig.) [de

  5. Optimal recombination in genetic algorithms for combinatorial optimization problems: Part II

    Directory of Open Access Journals (Sweden)

    Eremeev Anton V.

    2014-01-01

    Full Text Available This paper surveys results on complexity of the optimal recombination problem (ORP, which consists in finding the best possible offspring as a result of a recombination operator in a genetic algorithm, given two parent solutions. In Part II, we consider the computational complexity of ORPs arising in genetic algorithms for problems on permutations: the Travelling Salesman Problem, the Shortest Hamilton Path Problem and the Makespan Minimization on Single Machine and some other related problems. The analysis indicates that the corresponding ORPs are NP-hard, but solvable by faster algorithms, compared to the problems they are derived from.

  6. Social class, political power, and the state: their implications in medicine--parts I and II.

    Science.gov (United States)

    Navarro, V

    1976-01-01

    This three part article presents an anlysis of the distribution of power and of the nature of the state in Western industrialized societies and details their implications in medicine. Part I presents a critique of contemporary theories of the Western system of power; discusses the countervailing pluralist and power elite theories, as well as those of bureaucratic and professional control; and concludes with an examination of the Marxist theories of economic determinism, structural determinism, and corporate statism. Part II presents a Marxist theory of the role, nature, and characteristics of state intervention. Part III (which will appear in the next issue of this journal) focuses on the mode of that intervention and the reasons for its growth, with an added analysis of the attributes of state intervention in the health sector, and of the dialectical relationship between its growth and the current fiscal crisis of the state. In all three parts, the focus is on Western European countries and on North America, with many examples and categories from the area of medicine.

  7. Journal bearing

    Science.gov (United States)

    Menke, John R.; Boeker, Gilbert F.

    1976-05-11

    1. An improved journal bearing comprising in combination a non-rotatable cylindrical bearing member having a first bearing surface, a rotatable cylindrical bearing member having a confronting second bearing surface having a plurality of bearing elements, a source of lubricant adjacent said bearing elements for supplying lubricant thereto, each bearing element consisting of a pair of elongated relatively shallowly depressed surfaces lying in a cylindrical surface co-axial with the non-depressed surface and diverging from one another in the direction of rotation and obliquely arranged with respect to the axis of rotation of said rotatable member to cause a flow of lubricant longitudinally along said depressed surfaces from their distal ends toward their proximal ends as said bearing members are rotated relative to one another, each depressed surface subtending a radial angle of less than 360.degree., and means for rotating said rotatable bearing member to cause the lubricant to flow across and along said depressed surfaces, the flow of lubricant being impeded by the non-depressed portions of said second bearing surface to cause an increase in the lubricant pressure.

  8. Biology and Mechanics of Blood Flows Part II: Mechanics and Medical Aspects

    CERN Document Server

    Thiriet, Marc

    2008-01-01

    Biology and Mechanics of Blood Flows presents the basic knowledge and state-of-the-art techniques necessary to carry out investigations of the cardiovascular system using modeling and simulation. Part II of this two-volume sequence, Mechanics and Medical Aspects, refers to the extraction of input data at the macroscopic scale for modeling the cardiovascular system, and complements Part I, which focuses on nanoscopic and microscopic components and processes. This volume contains chapters on anatomy, physiology, continuum mechanics, as well as pathological changes in the vasculature walls including the heart and their treatments. Methods of numerical simulations are given and illustrated in particular by application to wall diseases. This authoritative book will appeal to any biologist, chemist, physicist, or applied mathematician interested in the functioning of the cardiovascular system.

  9. Assessing and addressing moral distress and ethical climate Part II: neonatal and pediatric perspectives.

    Science.gov (United States)

    Sauerland, Jeanie; Marotta, Kathleen; Peinemann, Mary Anne; Berndt, Andrea; Robichaux, Catherine

    2015-01-01

    Moral distress remains a pervasive and, at times, contested concept in nursing and other health care disciplines. Ethical climate, the conditions and practices in which ethical situations are identified, discussed, and decided, has been shown to exacerbate or ameliorate perceptions of moral distress. The purpose of this mixed-methods study was to explore perceptions of moral distress, moral residue, and ethical climate among registered nurses working in an academic medical center. Two versions of the Moral Distress Scale in addition to the Hospital Ethical Climate Survey were used, and participants were invited to respond to 2 open-ended questions. Part I reported the findings among nurses working in adult acute and critical care units. Part II presents the results from nurses working in pediatric/neonatal units. Significant differences in findings between the 2 groups are discussed. Subsequent interventions developed are also presented.

  10. Transferring diffractive optics from research to commercial applications: Part II - size estimations for selected markets

    Science.gov (United States)

    Brunner, Robert

    2014-04-01

    In a series of two contributions, decisive business-related aspects of the current process status to transfer research results on diffractive optical elements (DOEs) into commercial solutions are discussed. In part I, the focus was on the patent landscape. Here, in part II, market estimations concerning DOEs for selected applications are presented, comprising classical spectroscopic gratings, security features on banknotes, DOEs for high-end applications, e.g., for the semiconductor manufacturing market and diffractive intra-ocular lenses. The derived market sizes are referred to the optical elements, itself, rather than to the enabled instruments. The estimated market volumes are mainly addressed to scientifically and technologically oriented optical engineers to serve as a rough classification of the commercial dimensions of DOEs in the different market segments and do not claim to be exhaustive.

  11. Design of site specific radiopharmaceuticals for tumor imaging. (Parts I and II)

    International Nuclear Information System (INIS)

    Van Dort, M.E.

    1983-01-01

    Part I. Synthetic methods were developed for the preparation of several iodinated benzoic acid hydrazides as labeling moieties for indirect tagging of carbonyl-containing bio-molecules and potential tumor-imaging agents. Biodistribution studies conducted in mice on the derivatives having the I-125 label ortho to a phenolic OH demonstrated a rapid in vivo deiodination. Part II. The reported high melanin binding affinity of quinoline and other heterocyclic antimalarial drugs led to the development of many analogues of such molecules as potential melanoma-imaging agents. Once such analogue iodochloroquine does exhibit high melanin binding, but has found limited clinical use due to appreciable accumulation in non-target tissues such as the adrenal cortex and inner ear. This project developed a new series of candidate melanoma imaging agents which would be easier to radio-label, could yield higher specific activity product, and which might demonstrate more favorable pharmacokinetic and dosimetric characteristics compared to iodochloroquine

  12. Tunable, Flexible and Efficient Optimization of Control Pulses for Superconducting Qubits, part II - Applications

    Science.gov (United States)

    AsséMat, Elie; Machnes, Shai; Tannor, David; Wilhelm-Mauch, Frank

    In part I, we presented the theoretic foundations of the GOAT algorithm for the optimal control of quantum systems. Here in part II, we focus on several applications of GOAT to superconducting qubits architecture. First, we consider a control-Z gate on Xmons qubits with an Erf parametrization of the optimal pulse. We show that a fast and accurate gate can be obtained with only 16 parameters, as compared to hundreds of parameters required in other algorithms. We present numerical evidences that such parametrization should allow an efficient in-situ calibration of the pulse. Next, we consider the flux-tunable coupler by IBM. We show optimization can be carried out in a more realistic model of the system than was employed in the original study, which is expected to further simplify the calibration process. Moreover, GOAT reduced the complexity of the optimal pulse to only 6 Fourier components, composed with analytic wrappers.

  13. 75 FR 844 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, from the People's Republic of...

    Science.gov (United States)

    2010-01-06

    ... Parts Thereof, Finished and Unfinished, from the People's Republic of China: Final Results of the 2007... Republic of China: Preliminary Results of the 2007-2008 Administrative Review of the Antidumping Duty Order..., through May 31, 2008. The administrative [[Page 845

  14. Ruthenium(II) bipyridine complexes bearing new keto-enol azoimine ligands: synthesis, structure, electrochemistry and DFT calculations.

    Science.gov (United States)

    Al-Noaimi, Mousa; Awwadi, Firas F; Mansi, Ahmad; Abdel-Rahman, Obadah S; Hammoudeh, Ayman; Warad, Ismail

    2015-01-25

    The novel azoimine ligand, Ph-NH-N=C(COCH3)-NHPh(C≡CH) (H2L), was synthesized and its molecular structure was determined by X-ray crystallography. Catalytic hydration of the terminal acetylene of H2L in the presence of RuCl3·3H2O in ethanol at reflux temperature yielded a ketone (L1=Ph-N=N-C(COCH3)=N-Ph(COCH3) and an enol (L2=Ph-N=N-C(COCH3)=N-PhC(OH)=CH2) by Markovnikov addition of water. Two mixed-ligand ruthenium complexes having general formula, trans-[Ru(bpy)(Y)Cl2] (1-2) (where Y=L1 (1) and Y=L2 (2), bpy is 2.2'-bipyrdine) were achieved by the stepwise addition of equimolar amounts of (H2L) and bpy ligands to RuCl3·3H2O in absolute ethanol. Theses complexes were characterized by elemental analyses and spectroscopic (IR, UV-Vis, and NMR (1D (1)H NMR, (13)C NMR, (DEPT-135), (DEPT-90), 2D (1)H-(1)H and (13)C-(1)H correlation (HMQC) spectroscopy)). The two complexes exhibit a quasi-reversible one electron Ru(II)/Ru(III) oxidation couple at 604 mV vs. ferrocene/ferrocenium (Cp2Fe(0/+)) couple along with one electron ligand reduction at -1010 mV. The crystal structure of complex 1 showed that the bidentate ligand L1 coordinates to Ru(II) by the azo- and imine-nitrogen donor atoms. The complex adopts a distorted trans octahedral coordination geometry of chloride ligands. The electronic spectra of 1 and 1+ in dichloromethane have been modeled by time-dependent density functional theory (TD-DFT). Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Sampling and analysis plan for Phase II of the Bear Creek Valley Treatability Study, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1997-09-01

    The Bear Creek Valley (BCV) Treatability Study is intended to provide site-specific data defining potential treatment technologies applicable to contaminated groundwater and surface water. This project directly supports Alternative 5 of the base action in the BCV Feasibility Study and indirectly supports other alternatives through proof of concept. In that role, the ultimate goal is to install a treatment system that will remove uranium and nitrate from groundwater before it reaches Bear Creek. A secondary goal is the concurrent removal of technetium and several metals that affect ecological risk. This project is intended to produce hydraulic and treatment performance data required to design the treatment system to reach those goals. This project will also generate information that can be applied at other facilities within the Oak Ridge Reservation. This report is the sampling and analysis plan (SAP) for the field work component of Phase II of the BCV Treatability Study. Field work for this phase of the BCV Treatability Study consists of environmental and media testing. The SAP addresses environmental sampling at the S-3 Site at the Oak Ridge Y-12 Plant. Samples will be taken from groundwater, surface water, seeps, effluent from test columns, effluent from an algal mat reactor, and effluent from a pilot-scale wetland. Groundwater, surface water, and seeps will be monitored continuously for field parameters and sampled for analytical parameters during pump tests conducted periodically during the investigation. In-field continuous flow tests will be conducted over an extended time period (5 weeks) to generate data on long-term treatment effects on potential treatment effects on potential treatment media including sorbents and zero valent iron, over 28 weeks for constructed wetlands treatment, and over 24 weeks for algal mats treatment

  16. A study of drying and cleaning methods used in preparation for fluorescent penetrant inspection - Part II

    International Nuclear Information System (INIS)

    Brasche, L.; Lopez, R.; Larson, B.

    2003-01-01

    Fluorescent penetrant inspection is the most widely used method for aerospace components such as critical rotating components of gas turbine engines. Successful use of FPI begins with a clean and dry part, followed by a carefully controlled and applied FPI process, and conscientious inspection by well trained personnel. A variety of cleaning methods are in use for cleaning of titanium and nickel parts with selection based on the soils or contamination to be removed. Cleaning methods may include chemical or mechanical methods with sixteen different types studied as part of this program. Several options also exist for use in drying parts prior to FPI. Samples were generated and exposed to a range of conditions to study the effect of both drying and cleaning methods on the flaw response of FPI. Low cycle fatigue (LCF) cracks were generated in approximately 40 nickel and 40 titanium samples for evaluation of the various cleaning methods. Baseline measurements were made for each of the samples using a photometer to measure sample brightness and a UVA videomicroscope to capture digital images of the FPI indications. Samples were exposed to various contaminants, cleaned and inspected. Brightness measurements and digital images were also taken to compare to the baseline data. A comparison of oven drying to flash dry in preparation for FPI has been completed and will be reported in Part I. Comparison of the effectiveness of various cleaning methods for the contaminants will be presented in Part II. The cleaning and drying studies were completed in cooperation with Delta Airlines using cleaning, drying and FPI processes typical of engine overhaul processes and equipment. The work was completed as part of the Engine Titanium Consortium and included investigators from Honeywell, General Electric, Pratt and Whitney, and Rolls Royce

  17. Delivery systems for biopharmaceuticals. Part II: Liposomes, Micelles, Microemulsions and Dendrimers.

    Science.gov (United States)

    Silva, Ana C; Lopes, Carla M; Lobo, José M S; Amaral, Maria H

    2015-01-01

    Biopharmaceuticals are a generation of drugs that include peptides, proteins, nucleic acids and cell products. According to their particular molecular characteristics (e.g. high molecular size, susceptibility to enzymatic activity), these products present some limitations for administration and usually parenteral routes are the only option. To avoid these limitations, different colloidal carriers (e.g. liposomes, micelles, microemulsions and dendrimers) have been proposed to improve biopharmaceuticals delivery. Liposomes are promising drug delivery systems, despite some limitations have been reported (e.g. in vivo failure, poor long-term stability and low transfection efficiency), and only a limited number of formulations have reached the market. Micelles and microemulsions require more studies to exclude some of the observed drawbacks and guarantee their potential for use in clinic. According to their peculiar structures, dendrimers have been showing good results for nucleic acids delivery and a great development of these systems during next years is expected. This is the Part II of two review articles, which provides the state of the art of biopharmaceuticals delivery systems. Part II deals with liposomes, micelles, microemulsions and dendrimers.

  18. Emerging Forms of the Part II of Jonathan Swift's Novel “Gulliver’s Travels”

    Directory of Open Access Journals (Sweden)

    Svitlana Tikhonenko

    2017-11-01

    Full Text Available The article is devoted to the study of grotesque forms in Jonathan Swift's novel "Gulliver’s Travels" based on the text of part II of the novel "A Voyage to Brobdingnag". On the basis of the selected actual material, displays of the grotesque elements in the semantic field of the work’s text are traced. The grotesque world of the novel is the author's model of mankind, in which J. Swift presents his view not only on the state of the modern system of England, but also on the nature of man in general, reveals the peculiarities of the psychology of human nature, especially human socialization. In part II, the author continues to develop a complex and contradictory picture of human existence in front of the reader, the world of giants appears as an ambivalent system in which the features of an ideal society and ideal ruler, in author’s opinion, with the ugly face of man and society, are marvelously combined.

  19. Mineral resources of parts of the Departments of Antioquia and Caldas, Zone II, Colombia

    Science.gov (United States)

    Hall, R.B.; Feininger, Tomas; Barrero, L.; Dario, Rico H.; ,; Alvarez, A.

    1970-01-01

    The mineral resources of an area of 40,000 sq km, principally in the Department of Antioquia, but including small parts of the Departments of Caldas, C6rdoba, Risaralda, and Tolima, were investigated during the period 1964-68. The area is designated Zone II by the Colombian Inventario Minero Nacional(lMN). The geology of approximately 45 percent of this area, or 18,000 sq km, has been mapped by IMN. Zone II has been a gold producer for centuries, and still produces 75 percent of Colombia's gold. Silver is recovered as a byproduct. Ferruginous laterites have been investigated as potential sources of iron ore but are not commercially exploitable. Nickeliferous laterite on serpentinite near Ure in the extreme northwest corner of the Zone is potentially exploitable, although less promising than similar laterites at Cerro Matoso, north of the Zone boundary. Known deposits of mercury, chromium, manganese, and copper are small and have limited economic potentia1. Cement raw materials are important among nonmetallic resources, and four companies are engaged in the manufacture of portland cement. The eastern half of Zone II contains large carbonate rock reserves, but poor accessibility is a handicap to greater development at present. Dolomite near Amalfi is quarried for the glass-making and other industries. Clay saprolite is abundant and widely used in making brick and tiles in backyard kilns. Kaolin of good quality near La Union is used by the ceramic industry. Subbituminous coal beds of Tertiary are an important resource in the western part of the zone and have good potential for greater development. Aggregate materials for construction are varied and abundant. Deposits of sodic feldspar, talc, decorative stone, and silica are exploited on a small scale. Chrysotils asbestos deposits north of Campamento are being developed to supply fiber for Colombia's thriving asbestos-cement industry, which is presently dependent upon imported fiber. Wollastonite and andalusite are

  20. Synthesis and Biological Evaluation of Ru(II) and Pt(II) Complexes Bearing Carboxyl Groups as Potential Anticancer Targeted Drugs.

    Science.gov (United States)

    Martínez, Ma Ángeles; Carranza, M Pilar; Massaguer, Anna; Santos, Lucia; Organero, Juan A; Aliende, Cristina; de Llorens, Rafael; Ng-Choi, Iteng; Feliu, Lidia; Planas, Marta; Rodríguez, Ana M; Manzano, Blanca R; Espino, Gustavo; Jalón, Félix A

    2017-11-20

    The synthesis and characterization of Pt(II) (1 and 2) and Ru(II) arene (3 and 4) or polypyridine (5 and 6) complexes is described. With the aim of having a functional group to form bioconjugates, one uncoordinated carboxyl group has been introduced in all complexes. Some of the complexes were selected for their potential in photodynamic therapy (PDT). The molecular structures of complexes 2 and 5, as well as that of the sodium salt of the 4'-(4-carboxyphenyl)-2,2':6',2″-terpyridine ligand (cptpy), were determined by X-ray diffraction. Different techniques were used to evaluate the binding capacity to model DNA molecules, and MTT cytotoxicity assays were performed against four cell lines. Compounds 3, 4, and 5 showed little tendency to bind to DNA and exhibited poor biological activity. Compound 2 behaves as bonded to DNA probably through a covalent interaction, although its cytotoxicity was very low. Compound 1 and possibly 6, both of which contain a cptpy ligand, were able to intercalate with DNA, but toxicity was not observed for 6. However, compound 1 was active in all cell lines tested. Clonogenic assays and apoptosis induction studies were also performed on the PC-3 line for 1. The photodynamic behavior for complexes 1, 5, and 6 indicated that their nuclease activity was enhanced after irradiation at λ = 447 nm. The cell viability was significantly reduced only in the case of 5. The different behavior in the absence or presence of light makes complex 5 a potential prodrug of interest in PDT. Molecular docking studies followed by molecular dynamics simulations for 1 and the counterpart without the carboxyl group confirmed the experimental data that pointed to an intercalation mechanism. The cytotoxicity of 1 and the potential of 5 in PDT make them good candidates for subsequent conjugation, through the carboxyl group, to "selected peptides" which could facilitate the selective vectorization of the complex toward receptors that are overexpressed in

  1. Seismic risk analysis for General Electric Plutonium Facility, Pleasanton, California. Final report, part II

    International Nuclear Information System (INIS)

    1980-01-01

    This report is the second of a two part study addressing the seismic risk or hazard of the special nuclear materials (SNM) facility of the General Electric Vallecitos Nuclear Center at Pleasanton, California. The Part I companion to this report, dated July 31, 1978, presented the seismic hazard at the site that resulted from exposure to earthquakes on the Calaveras, Hayward, San Andreas and, additionally, from smaller unassociated earthquakes that could not be attributed to these specific faults. However, while this study was in progress, certain additional geologic information became available that could be interpreted in terms of the existance of a nearby fault. Although substantial geologic investigations were subsequently deployed, the existance of this postulated fault, called the Verona Fault, remained very controversial. The purpose of the Part II study was to assume the existance of such a capable fault and, under this assumption, to examine the loads that the fault could impose on the SNM facility. This report first reviews the geologic setting with a focus on specifying sufficient geologic parameters to characterize the postulated fault. The report next presents the methodology used to calculate the vibratory ground motion hazard. Because of the complexity of the fault geometry, a slightly different methodology is used here compared to the Part I report. This section ends with the results of the calculation applied to the SNM facility. Finally, the report presents the methodology and results of the rupture hazard calculation

  2. Two-loop renormalization in the standard model, part II. Renormalization procedures and computational techniques

    Energy Technology Data Exchange (ETDEWEB)

    Actis, S. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Passarino, G. [Torino Univ. (Italy). Dipt. di Fisica Teorica; INFN, Sezione di Torino (Italy)

    2006-12-15

    In part I general aspects of the renormalization of a spontaneously broken gauge theory have been introduced. Here, in part II, two-loop renormalization is introduced and discussed within the context of the minimal Standard Model. Therefore, this paper deals with the transition between bare parameters and fields to renormalized ones. The full list of one- and two-loop counterterms is shown and it is proven that, by a suitable extension of the formalism already introduced at the one-loop level, two-point functions suffice in renormalizing the model. The problem of overlapping ultraviolet divergencies is analyzed and it is shown that all counterterms are local and of polynomial nature. The original program of 't Hooft and Veltman is at work. Finite parts are written in a way that allows for a fast and reliable numerical integration with all collinear logarithms extracted analytically. Finite renormalization, the transition between renormalized parameters and physical (pseudo-)observables, are discussed in part III where numerical results, e.g. for the complex poles of the unstable gauge bosons, are shown. An attempt is made to define the running of the electromagnetic coupling constant at the two-loop level. (orig.)

  3. New ruthenium(II) carbonyl complexes bearing disulfide Schiff base ligands and their applications as catalyst for some organic transformations

    Science.gov (United States)

    Prakash, Govindan; Viswanathamurthi, Periasamy

    2014-08-01

    Schiff base disulfide ligands (H2L1-6) were synthesized from the condensation of cystamine with salicylaldehyde(H2L1), 5-chlorosalicylaldehyde(H2L2), o-vanillin(H2L3), 2-hydroxyacetophenone(H2L4), 3-methyl-2-hydroxyacetophenone(H2L5), and 2-hydroxy-1-naphthaldehyde(H2L6). H2L1-6 reacts with the ruthenium precursor complex [RuHCl(CO)(PPh3)3] in benzene giving rise to six new ruthenium(II) complexes of general formula [Ru(CO)L1-6]. Characterization of the new complexes was carried out by using elemental and spectral (IR, UV-Vis, NMR (1H and 13C) and Mass) techniques. An octahedral geometry was assigned for all the complexes based on the spectral data obtained. The catalytic efficiency of the new complexes in aldehyde to amide conversion in the presence of NaHCO3, N-alkylation of aniline in the presence of t-BuOK, and transfer hydrogenation of ketones in the presence of iPrOH/KOH reactions were studied. Furthermore, the effect of solvents and catalyst/substrate ratio on the catalytic aldehyde to amide conversion were also discussed.

  4. ALTERNATIVE BINDERS TO BENTONITE FOR IRON ORE PELLETIZING : PART II : EFFECTS ON METALLURGICAL AND CHEMICAL PROPERTIES

    Directory of Open Access Journals (Sweden)

    Osman Sivrikaya

    2014-07-01

    Full Text Available This study was started to find alternative binders to bentonite and to recover the low preheated and fired pellet mechanical strengths of organic binders-bonded pellets. Bentonite is considered as a chemical impurity for pellet chemistry due to acid constituents (SiO2 and Al2O3. Especially addition of silica-alumina bearing binders is detrimental for iron ore concentrate with high acidic content. Organic binders are the most studied binders since they are free in silica. Although they yield pellets with good wet strength; they have found limited application in industry since they fail to give sufficient physical and mechanical strength to preheated and fired pellets. It is investigated that how insufficient preheated and fired pellet strengths can be improved when organic binders are used as binder. The addition of a slag bonding/strength increasing constituent (free in acidic contents into pellet feed to provide pellet strength with the use of organic binders was proposed. Addition of boron compounds such as colemanite, tincal, borax pentahydrate, boric acid together with organic binders such as CMC, starch, dextrin and some organic based binders, into magnetite and hematite pellet mixture was tested. After determining the addition of boron compounds is beneficial to recover the low pellet physical and mechanical qualities in the first part of this study, in this second part, metallurgical and chemical properties (reducibility - swelling index – microstructure – mineralogy - chemical content of pellets produced with combined binders (an organic binder plus a boron compound were presented. The metallurgical and chemical tests results showed that good quality product pellets can be produced with combined binders when compared with the bentonite-bonded pellets. Hence, the suggested combined binders can be used as binder in place of bentonite in iron ore pelletizing without compromising the pellet chemistry.

  5. Polar bears at risk

    Energy Technology Data Exchange (ETDEWEB)

    Norris, S.; Rosentrater, L.; Eid, P.M. [WWF International Arctic Programme, Oslo (Norway)

    2002-05-01

    rains also destroy the denning habitat of ringed seals, the polar bears' primary prey. Declines in the ringed seal population would mean a loss of food for polar bears. A trend toward stronger winds and increasing ice drift observed in some parts of the Arctic over the last five decades will likely increase energy expenditures and stress levels in polar bears that spend most of their lives on drifting sea ice. Polar bears face other limiting factors as well. Historically, the main threat to polar bears has been hunting. Satisfactory monitoring information has been obtained for most polar bear populations in recent years, however there is concern about hunting in areas without formal quota systems, such as Greenland. A range of toxic pollutants, including heavy metals, radioactivity, and persistent organic pollutants (POPs) are found throughout the Arctic. Of greatest concern are the effects of POPs on polar bears, which include a general weakening of the immune system, reduced reproductive success and physical deformities. The expansion of oil development in the Arctic poses additional threats; for example, disturbances to denning females in the Arctic National Wildlife Refuge in Alaska could undermine recruitment of the Beaufort Sea polar bear population. These threats, along with other effects of human activity in the Arctic, combine to pressure polar bears and their habitat. Large carnivores are sensitive indicators of ecosystem health and can be used to define the minimum area necessary to preserve intact ecosystems. WWF has identified the polar bear as a unique symbol of the complexities and interdependencies of the arctic marine ecosystem as it works toward its goal of preserving biodiversity for future generations.

  6. GAS BEARING

    Science.gov (United States)

    Skarstrom, C.W.

    1960-09-01

    A gas lubricated bearing for a rotating shaft is described. The assembly comprises a stationary collar having an annular member resiliently supported thereon. The collar and annular member are provided with cooperating gas passages arranged for admission of pressurized gas which supports and lubricates a bearing block fixed to the rotatable shaft. The resilient means for the annular member support the latter against movement away from the bearing block when the assembly is in operation.

  7. Grizzly bear

    Science.gov (United States)

    Schwartz, C.C.; Miller, S.D.; Haroldson, M.A.; Feldhamer, G.; Thompson, B.; Chapman, J.

    2003-01-01

    The grizzly bear inspires fear, awe, and respect in humans to a degree unmatched by any other North American wild mammal. Like other bear species, it can inflict serious injury and death on humans and sometimes does. Unlike the polar bear (Ursus maritimus) of the sparsely inhabited northern arctic, however, grizzly bears still live in areas visited by crowds of people, where presence of the grizzly remains physically real and emotionally dominant. A hike in the wilderness that includes grizzly bears is different from a stroll in a forest from which grizzly bears have been purged; nighttime conversations around the campfire and dreams in the tent reflect the presence of the great bear. Contributing to the aura of the grizzly bear is the mixture of myth and reality about its ferocity. unpredictable disposition, large size, strength, huge canines, long claws, keen senses, swiftness, and playfulness. They share characteristics with humans such as generalist life history strategies. extended periods of maternal care, and omnivorous diets. These factors capture the human imagination in ways distinct from other North American mammals. Precontact Native American legends reflected the same fascination with the grizzly bear as modern stories and legends (Rockwell 1991).

  8. Best management practices plan for Phase II of the Bear Creek Valley treatability study Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1997-05-01

    The Oak Ridge Y-12 Plant site is currently under a Federal Facilities Agreement to define soil and groundwater contamination and develop remedies to protect human health and the environment. The western end of the site is known to have a former nitric acid disposal pit that has been remediated and capped. Remedial investigation data indicate this pit was a source of nitrate, uranium, technetium, and other metals contamination in groundwater. The downgradient receptor of this contamination includes Bear Creek and its tributaries. A feasibility study is underway to develop a remedy to prevent further contaminant migration to this receptor. To support the feasibility study, a treatability study is being completed to examine groundwater treatment at the S-3 site. This document serves as the top level command medium for Phase II and as such will be the primary resource for management and implementation of field activities. Many of the details and standard operating procedures referred within this document can be found in other Lockheed Martin Energy Systems (Energy Systems) documents. Several supporting documents specific to this project are also cited. These include the Sampling and Analysis Plan (SAP), the Health and Safety Plan (HASP), and the Waste Management Plan (WMP). Section 1 describes the results of Phase I efforts. Section 2 describes the objectives of Phase II. Section 3 provides details of field testing. Section 4 addresses the HASP. Section 5 describes the SAP. Section 6 introduces the WMP. Environmental compliance issues are discussed in Section 7, and sediment and erosion control is addressed in Section 8. Information about the project team is provided in Section 9

  9. A comprehensive review and update on the biologic treatment of adult noninfectious uveitis: part II.

    Science.gov (United States)

    Lee, Kyungmin; Bajwa, Asima; Freitas-Neto, Clovis A; Metzinger, Jamie Lynne; Wentworth, Bailey A; Foster, C Stephen

    2014-11-01

    Treatment of adult, noninfectious uveitis remains a major challenge for ophthalmologists around the world, especially in regard to recalcitrant cases. It is reported to comprise approximately 10% of preventable blindness in the USA. The cause of uveitis can be idiopathic or associated with infectious and systemic disorders. The era of biologic medical therapies provides new options for patients with otherwise treatment-resistant inflammatory eye disease. This two-part review gives a comprehensive overview of the existing medical treatment options for patients with adult, noninfectious uveitis, as well as important advances for the treatment ocular inflammation. Part I covers classic immunomodulation and latest information on corticosteroid therapy. In part II, emerging therapies are discussed, including biologic response modifiers, experimental treatments and ongoing clinical studies for uveitis. The hazard of chronic corticosteroid use in the treatment of adult, noninfectious uveitis is well documented. Corticosteroid-sparing therapies, which offer a very favorable risk-benefit profile when administered properly, should be substituted. Although nothing is currently approved for on-label use in this indication, many therapies, through either translation or novel basic science research, have the potential to fill the currently exposed gaps.

  10. Impact of monovalent cations on soil structure. Part II. Results of two Swiss soils

    Science.gov (United States)

    Farahani, Elham; Emami, Hojat; Keller, Thomas

    2018-01-01

    In this study, we investigated the impact of adding solutions with different potassium and sodium concentrations on dispersible clay, water retention characteristics, air permeability, and soil shrinkage behaviour using two agricultural soils from Switzerland with different clay content but similar organic carbon to clay ratio. Three different solutions (including only Na, only K, and the combination of both) were added to soil samples at three different cation ratio of soil structural stability levels, and the soil samples were incubated for one month. Our findings showed that the amount of readily dispersible clay increased with increasing Na concentrations and with increasing cation ratio of soil structural stability. The treatment with the maximum Na concentration resulted in the highest water retention and in the lowest shrinkage capacity. This was was associated with high amounts of readily dispersible clay. Air permeability generally increased during incubation due to moderate wetting and drying cycles, but the increase was negatively correlated with readily dispersible clay. Readily dispersible clay decreased with increasing K, while readily dispersible clay increased with increasing K in Iranian soil (Part I of our study). This can be attributed to the different clay mineralogy of the studied soils (muscovite in Part I and illite in Part II).

  11. Music in the exercise domain: a review and synthesis (Part II).

    Science.gov (United States)

    Karageorghis, Costas I; Priest, David-Lee

    2012-03-01

    Since a 1997 review by Karageorghis and Terry, which highlighted the state of knowledge and methodological weaknesses, the number of studies investigating musical reactivity in relation to exercise has swelled considerably. In this two-part review paper, the development of conceptual approaches and mechanisms underlying the effects of music are explicated (Part I), followed by a critical review and synthesis of empirical work (spread over Parts I and II). Pre-task music has been shown to optimise arousal, facilitate task-relevant imagery and improve performance in simple motoric tasks. During repetitive, endurance-type activities, self-selected, motivational and stimulative music has been shown to enhance affect, reduce ratings of perceived exertion, improve energy efficiency and lead to increased work output. There is evidence to suggest that carefully selected music can promote ergogenic and psychological benefits during high-intensity exercise, although it appears to be ineffective in reducing perceptions of exertion beyond the anaerobic threshold. The effects of music appear to be at their most potent when it is used to accompany self-paced exercise or in externally valid conditions. When selected according to its motivational qualities, the positive impact of music on both psychological state and performance is magnified. Guidelines are provided for future research and exercise practitioners.

  12. The prediction of creep damage in Type 347 weld metal: part II creep fatigue tests

    International Nuclear Information System (INIS)

    Spindler, M.W.

    2005-01-01

    Calculations of creep damage under conditions of strain control are often carried out using either a time fraction approach or a ductility exhaustion approach. In part I of this paper the rupture strength and creep ductility data for a Type 347 weld metal were fitted to provide the material properties that are used to calculate creep damage. Part II of this paper examines whether the time fraction approach or the ductility exhaustion approach gives the better predictions of creep damage in creep-fatigue tests on the same Type 347 weld metal. In addition, a new creep damage model, which was developed by removing some of the simplifying assumptions that are made in the ductility exhaustion approach, was used. This new creep damage model is a function of the strain rate, stress and temperature and was derived from creep and constant strain rate test data using a reverse modelling technique (see part I of this paper). It is shown that the new creep damage model gives better predictions of creep damage in the creep-fatigue tests than the time fraction and the ductility exhaustion approaches

  13. Noncardiac findings on cardiac CT. Part II: spectrum of imaging findings.

    LENUS (Irish Health Repository)

    Killeen, Ronan P

    2012-02-01

    Cardiac computed tomography (CT) has evolved into an effective imaging technique for the evaluation of coronary artery disease in selected patients. Two distinct advantages over other noninvasive cardiac imaging methods include its ability to directly evaluate the coronary arteries and to provide a unique opportunity to evaluate for alternative diagnoses by assessing the extracardiac structures, such as the lungs and mediastinum, particularly in patients presenting with the chief symptom of acute chest pain. Some centers reconstruct a small field of view (FOV) cropped around the heart but a full FOV (from skin to skin in the area irradiated) is obtainable in the raw data of every scan so that clinically relevant noncardiac findings are identifiable. Debate in the scientific community has centered on the necessity for this large FOV. A review of noncardiac structures provides the opportunity to make alternative diagnoses that may account for the patient\\'s presentation or to detect important but clinically silent problems such as lung cancer. Critics argue that the yield of biopsy-proven cancers is low and that the follow-up of incidental noncardiac findings is expensive, resulting in increased radiation exposure and possibly unnecessary further testing. In this 2-part review we outline the issues surrounding the concept of the noncardiac read, looking for noncardiac findings on cardiac CT. Part I focused on the pros and cons for and against the practice of identifying noncardiac findings on cardiac CT. Part II illustrates the imaging spectrum of cardiac CT appearances of benign and malignant noncardiac pathology.

  14. Multiobjective Optimization for Fixture Locating Layout of Sheet Metal Part Using SVR and NSGA-II

    Directory of Open Access Journals (Sweden)

    Yuan Yang

    2017-01-01

    Full Text Available Fixture plays a significant role in determining the sheet metal part (SMP spatial position and restraining its excessive deformation in many manufacturing operations. However, it is still a difficult task to design and optimize SMP fixture locating layout at present because there exist multiple conflicting objectives and excessive computational cost of finite element analysis (FEA during the optimization process. To this end, a new multiobjective optimization method for SMP fixture locating layout is proposed in this paper based on the support vector regression (SVR surrogate model and the elitist nondominated sorting genetic algorithm (NSGA-II. By using ABAQUS™ Python script interface, a parametric FEA model is established. And the fixture locating layout is treated as design variables, while the overall deformation and maximum deformation of SMP under external forces are as the multiple objective functions. First, a limited number of training and testing samples are generated by combining Latin hypercube design (LHD with FEA. Second, two SVR prediction models corresponding to the multiple objectives are established by learning from the limited training samples and are integrated as the multiobjective optimization surrogate model. Third, NSGA-II is applied to determine the Pareto optimal solutions of SMP fixture locating layout. Finally, a multiobjective optimization for fixture locating layout of an aircraft fuselage skin case is conducted to illustrate and verify the proposed method.

  15. CERN scientists take part in the Tevatron Run II performance review committee

    CERN Multimedia

    Maximilien Brice

    2002-01-01

    Tevatron Run II is under way at Fermilab, exploring the high-energy frontier with upgraded detectors that will address some of the biggest questions in particle physics.Until CERN's LHC switches on, the Tevatron proton-antiproton collider is the world's only source of top quarks. It is the only place where we can search for supersymmetry, for the Higgs boson, and for signatures of additional dimensions of space-time. The US Department of Energy (DOE) recently convened a high-level international review committee to examine Fermilab experts' first-phase plans for the accelerator complex. Pictured here with a dipole magnet in CERN's LHC magnet test facility are the four CERN scientists who took part in the DOE's Tevatron review. Left to right: Francesco Ruggiero, Massimo Placidi, Flemming Pedersen, and Karlheinz Schindl. Further information: CERN Courier 43 (1)

  16. Implementing AORN recommended practices for a safe environment of care, part II.

    Science.gov (United States)

    Kennedy, Lynne

    2014-09-01

    Construction in and around a working perioperative suite is a challenge beyond merely managing traffic patterns and maintaining the sterile field. The AORN "Recommended practices for a safe environment of care, part II" provides guidance on building design; movement of patients, personnel, supplies, and equipment; environmental controls; safety and security; and control of noise and distractions. Whether the OR suite evolves through construction, reconstruction, or remodeling, a multidisciplinary team of construction experts and health care professionals should create a functional plan and communicate at every stage of the project to maintain a safe environment and achieve a well-designed outcome. Emergency preparedness, a facility-wide security plan, and minimization of noise and distractions in the OR also help enhance the safety of the perioperative environment. Copyright © 2014 AORN, Inc. Published by Elsevier Inc. All rights reserved.

  17. Instructional climates in preschool children who are at-risk. Part II: perceived physical competence.

    Science.gov (United States)

    Robinson, Leah E; Rudisill, Mary E; Goodway, Jacqueline D

    2009-09-01

    In Part II of this study, we examined the effect of two 9-week instructional climates (low-autonomy [LA] and mastery motivational climate [MMC]) on perceived physical competence (PPC) in preschoolers (N = 117). Participants were randomly assigned to an LA, MMC, or comparison group. PPC was assessed by a pretest, posttest, and retention test with the Pictorial Scale of Perceived Competence and Social Acceptance. A significant Treatment x Time interaction (p < .001) was present, supporting that MMC participants reported significantly higher PPC scores over time, while no positive changes were present in LA and comparison participants. The results show that an MMC leads to psychological benefits related to achievement motivation. These findings should encourage early childhood educators to consider the effect of instructional climates on children's self-perception.

  18. Magnetic resonance imaging of the elbow. Part II: Abnormalities of the ligaments, tendons, and nerves

    Energy Technology Data Exchange (ETDEWEB)

    Kijowski, Richard; Tuite, Michael; Sanford, Matthew [University of Wisconsin Hospital, Department of Radiology, Madison, WI (United States)

    2005-01-01

    Part II of this comprehensive review on magnetic resonance imaging of the elbow discusses the role of magnetic resonance imaging in evaluating patients with abnormalities of the ligaments, tendons, and nerves of the elbow. Magnetic resonance imaging can yield high-quality multiplanar images which are useful in evaluating the soft tissue structures of the elbow. Magnetic resonance imaging can detect tears of the ulnar collateral ligament and lateral collateral ligament of the elbow with high sensitivity and specificity. Magnetic resonance imaging can determine the extent of tendon pathology in patients with medial epicondylitis and lateral epicondylitis. Magnetic resonance imaging can detect tears of the biceps tendon and triceps tendon and can distinguishing between partial and complete tendon rupture. Magnetic resonance imaging is also helpful in evaluating patients with nerve disorders at the elbow. (orig.)

  19. Repository Planning, Design, and Engineering: Part II-Equipment and Costing.

    Science.gov (United States)

    Baird, Phillip M; Gunter, Elaine W

    2016-08-01

    Part II of this article discusses and provides guidance on the equipment and systems necessary to operate a repository. The various types of storage equipment and monitoring and support systems are presented in detail. While the material focuses on the large repository, the requirements for a small-scale startup are also presented. Cost estimates and a cost model for establishing a repository are presented. The cost model presents an expected range of acquisition costs for the large capital items in developing a repository. A range of 5,000-7,000 ft(2) constructed has been assumed, with 50 frozen storage units, to reflect a successful operation with growth potential. No design or engineering costs, permit or regulatory costs, or smaller items such as the computers, software, furniture, phones, and barcode readers required for operations have been included.

  20. Mechanical performance of carbon-epoxy laminates. Part II: quasi-static and fatigue tensile properties

    Directory of Open Access Journals (Sweden)

    José Ricardo Tarpani

    2006-06-01

    Full Text Available In Part II of this work, quasi-static tensile properties of four aeronautical grade carbon-epoxy composite laminates, in both the as-received and pre-fatigued states, have been determined and compared. Quasi-static mechanical properties assessed were tensile strength and stiffness, tenacity (toughness at the maximum load and for a 50% load drop-off. In general, as-molded unidirectional cross-ply carbon fiber (tape reinforcements impregnated with either standard or rubber-toughened epoxy resin exhibited the maximum performance. The materials also displayed a significant tenacification (toughening after exposed to cyclic loading, resulting from the increased stress (the so-called wear-in phenomenon and/or strain at the maximum load capacity of the specimens. With no exceptions, two-dimensional woven textile (fabric pre-forms fractured catastrophically under identical cyclic loading conditions imposed to the fiber tape architecture, thus preventing their residual properties from being determined.

  1. Superconducting composite for magnetic bearings

    International Nuclear Information System (INIS)

    Rigney, T.K. II.

    1995-01-01

    A composite includes granules of Type II superconducting material and granules of rare-earth permanent magnets that are distributed in a binder. The composite is a two-phase structure that combines the properties of the superconductor and magnets with the flexibility and toughness of a polymeric material. A bearing made from this composite has the load capacity and stiffness of a permanent magnet bearing with added stability from a Type II superconducting material. 7 figs

  2. Forecasting of reservoir pressures of oil and gas bearing complexes in northern part of West Siberia for safety oil and gas deposits exploration and development

    Science.gov (United States)

    Gorbunov, P. A.; Vorobyov, S. V.

    2017-10-01

    In the paper the features of reservoir pressures changes in the northern part of West Siberian oil-and gas province are described. This research is based on the results of hydrodynamic studies in prospecting and explorating wells in Yamal-Nenets Autonomous District. In the Cenomanian, Albian, Aptian and in the top of Neocomian deposits, according to the research, reservoir pressure is usually equal to hydrostatic pressure. At the bottom of the Neocomian and Jurassic deposits zones with abnormally high reservoir pressures (AHRP) are distinguished within Gydan and Yamal Peninsula and in the Nadym-Pur-Taz interfluve. Authors performed the unique zoning of the territory of the Yamal-Nenets Autonomous District according to the patterns of changes of reservoir pressures in the section of the sedimentary cover. The performed zoning and structural modeling allow authors to create a set of the initial reservoir pressures maps for the main oil and gas bearing complexes of the northern part of West Siberia. The results of the survey should improve the efficiency of exploration drilling by preventing complications and accidents during this operation in zones with abnormally high reservoir pressures. In addition, the results of the study can be used to estimate gas resources within prospective areas of Yamal-Nenets Autonomous District.

  3. Advances in Knowledge Discovery and Data Mining 21st Pacific Asia Conference, PAKDD 2017 Held in Jeju, South Korea, May 23 26, 2017. Proceedings Part I, Part II.

    Science.gov (United States)

    2017-06-27

    Data Mining 21’’ Pacific-Asia Conference, PAKDD 2017Jeju, South Korea, May 23-26, Sb. GRANT NUMBER 2017 Proceedings, Part I, Part II Sc. PROGRAM...Springer; Switzerland. 14. ABSTRACT The Pacific-Asia Conference on Knowledge Discovery and Data Mining (PAKDD) is a leading international conference...in the areas of knowledge discovery and data mining (KDD). We had three keynote speeches, delivered by Sang Cha from Seoul National University

  4. International Working Group on Fast Reactors Eight Annual Meeting, Vienna, Austria, 15-18 April 1975. Summary Report. Part II

    International Nuclear Information System (INIS)

    1975-07-01

    The Eighth Annual Meeting of the IAEA International Working Group on Past Reactors was held at the IAEA Headquarters in Vienna, Austria, from 15 to 18 April 1975. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programmes in the field of LMPBR’s and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

  5. Tobacco control and gender in south-east Asia. Part II: Singapore and Vietnam.

    Science.gov (United States)

    Morrow, Martha; Barraclough, Simon

    2003-12-01

    In the World Health Organization's Western Pacific Region, being born male is the single greatest risk marker for tobacco use. While the literature demonstrates that risks associated with tobacco use may vary according to sex, gender refers to the socially determined roles and responsibilities of men and women, who initiate, continue and quit using tobacco for complex and often different reasons. Cigarette advertising frequently appeals to gender roles. Yet tobacco control policy tends to be gender-blind. Using a broad, gender-sensitivity framework, this contradiction is explored in four Western Pacific countries. Part I of the study presented the rationale, methodology and design of the study, discussed issues surrounding gender and tobacco, and analysed developments in Malaysia and the Philippines (see the previous issue of this journal). Part II deals with Singapore and Vietnam. In all four countries gender was salient for the initiation and maintenance of smoking. Yet, with a few exceptions, gender was largely unrecognized in control policy. Suggestions for overcoming this weakness in order to enhance tobacco control are made.

  6. Interview-Based Qualitative Research in Emergency Care Part II: Data Collection, Analysis and Results Reporting

    Science.gov (United States)

    Ranney, Megan L.; Meisel, Zachary; Choo, Esther K.; Garro, Aris; Sasson, Comilla; Morrow, Kathleen

    2015-01-01

    Qualitative methods are increasingly being used in emergency care research. Rigorous qualitative methods can play a critical role in advancing the emergency care research agenda by allowing investigators to generate hypotheses, gain an in-depth understanding of health problems or specific populations, create expert consensus, and develop new intervention and dissemination strategies. In Part I of this two-article series, we provided an introduction to general principles of applied qualitative health research and examples of its common use in emergency care research, describing study designs and data collection methods most relevant to our field (observation, individual interviews, and focus groups). Here in Part II of this series, we outline the specific steps necessary to conduct a valid and reliable qualitative research project, with a focus on interview-based studies. These elements include building the research team, preparing data collection guides, defining and obtaining an adequate sample, collecting and organizing qualitative data, and coding and analyzing the data. We also discuss potential ethical considerations unique to qualitative research as it relates to emergency care research. PMID:26284572

  7. A case study of packaging waste collection systems in Portugal - Part II: Environmental and economic analysis.

    Science.gov (United States)

    Pires, Ana; Sargedas, João; Miguel, Mécia; Pina, Joaquim; Martinho, Graça

    2017-03-01

    An understanding of the environmental impacts and costs related to waste collection is needed to ensure that existing waste collection schemes are the most appropriate with regard to both environment and cost. This paper is Part II of a three-part study of a mixed packaging waste collection system (curbside plus bring collection). Here, the mixed collection system is compared to an exclusive curbside system and an exclusive bring system. The scenarios were assessed using life cycle assessment and an assessment of costs to the waste management company. The analysis focuses on the collection itself so as to be relevant to waste managers and decision-makers who are involved only in this step of the packaging life cycle. The results show that the bring system has lower environmental impacts and lower economic costs, and is capable of reducing the environmental impacts of the mixed system. However, a sensitivity analysis shows that these results could differ if the curbside collection were to be optimized. From economic and environmental perspectives, the mixed system has few advantages. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Adaptive Core Simulation Employing Discrete Inverse Theory - Part II: Numerical Experiments

    International Nuclear Information System (INIS)

    Abdel-Khalik, Hany S.; Turinsky, Paul J.

    2005-01-01

    Use of adaptive simulation is intended to improve the fidelity and robustness of important core attribute predictions such as core power distribution, thermal margins, and core reactivity. Adaptive simulation utilizes a selected set of past and current reactor measurements of reactor observables, i.e., in-core instrumentation readings, to adapt the simulation in a meaningful way. The companion paper, ''Adaptive Core Simulation Employing Discrete Inverse Theory - Part I: Theory,'' describes in detail the theoretical background of the proposed adaptive techniques. This paper, Part II, demonstrates several computational experiments conducted to assess the fidelity and robustness of the proposed techniques. The intent is to check the ability of the adapted core simulator model to predict future core observables that are not included in the adaption or core observables that are recorded at core conditions that differ from those at which adaption is completed. Also, this paper demonstrates successful utilization of an efficient sensitivity analysis approach to calculate the sensitivity information required to perform the adaption for millions of input core parameters. Finally, this paper illustrates a useful application for adaptive simulation - reducing the inconsistencies between two different core simulator code systems, where the multitudes of input data to one code are adjusted to enhance the agreement between both codes for important core attributes, i.e., core reactivity and power distribution. Also demonstrated is the robustness of such an application

  9. Interview-based Qualitative Research in Emergency Care Part II: Data Collection, Analysis and Results Reporting.

    Science.gov (United States)

    Ranney, Megan L; Meisel, Zachary F; Choo, Esther K; Garro, Aris C; Sasson, Comilla; Morrow Guthrie, Kate

    2015-09-01

    Qualitative methods are increasingly being used in emergency care research. Rigorous qualitative methods can play a critical role in advancing the emergency care research agenda by allowing investigators to generate hypotheses, gain an in-depth understanding of health problems or specific populations, create expert consensus, and develop new intervention and dissemination strategies. In Part I of this two-article series, we provided an introduction to general principles of applied qualitative health research and examples of its common use in emergency care research, describing study designs and data collection methods most relevant to our field (observation, individual interviews, and focus groups). Here in Part II of this series, we outline the specific steps necessary to conduct a valid and reliable qualitative research project, with a focus on interview-based studies. These elements include building the research team, preparing data collection guides, defining and obtaining an adequate sample, collecting and organizing qualitative data, and coding and analyzing the data. We also discuss potential ethical considerations unique to qualitative research as it relates to emergency care research. © 2015 by the Society for Academic Emergency Medicine.

  10. [Education in our time: competency or aptitude? The case for medicine. Part II].

    Science.gov (United States)

    Viniegra-Velázquez, Leonardo

    Part II is focused on participatory education (PE), a distinctive way to understand and practice education in contrast to passive education. The core of PE is to develop everyone's own cognitive potentialities frequently mutilated, neglected or ignored. Epistemological and experiential basis of PE are defined: the concept of incisive and creative criticism, the idea of knowledge as each person's own construct and life experience as the main focus of reflection and cognition. The PE aims towards individuals with unprecedented cognitive and creative faculties, capable of approaching a more inclusive and hospitable world. The last part criticizes the fact that medical education has remained among the passive education paradigm. The key role of cognitive aptitudes, both methodological and practical (clinical aptitude), in the progress of medical education and practice is emphasized. As a conclusion, the knowhow of education is discussed, aiming towards a better world away from human and planetary degradation. Copyright © 2017 Hospital Infantil de México Federico Gómez. Publicado por Masson Doyma México S.A. All rights reserved.

  11. Long-term solar activity and terrestrial connections. Part II: at the beckon of the sun?

    Directory of Open Access Journals (Sweden)

    N. D. Diamantides

    1998-05-01

    Full Text Available The research task described herein aims at the structuring of an analytical tool that traces the time course of geophysical phenomena, regional or global, and compares it to the course of long-term solar conditions, long-term meaning decades or a few centuries. The model is based on the premise that since in a last analysis the preponderance of atmospheric, hydrospheric, and, possibly, some aspects of geospheric phenomena are, or have been, powered by energy issuing from the sun - either now or in the past - the long-term behavior of such phenomena is ultimately "connected" to long-term changes occurring in the sun itself. Accordingly, the proposed research firstly derives and models a stable surrogate pattern for the long-term solar activity, secondly introduces a transfer-function algorithm for modeling the connection between the surrogate and terrestrial phenomena viewed as partners in the connection, and thirdly probes the connection outcome for episodic or unanticipated effects that may arise due to the fact that in the present context, the connection, should it exist, is very likely nonlinear. Part I of the study presents the theory of the concept, while Part II demonstrates the concept's pertinence to a number of terrestrial phenomena.Key words. Solar activity · Kolmogorov algorithm

  12. Long-term solar activity and terrestrial connections. Part II: at the beckon of the sun?

    Directory of Open Access Journals (Sweden)

    N. D. Diamantides

    Full Text Available The research task described herein aims at the structuring of an analytical tool that traces the time course of geophysical phenomena, regional or global, and compares it to the course of long-term solar conditions, long-term meaning decades or a few centuries. The model is based on the premise that since in a last analysis the preponderance of atmospheric, hydrospheric, and, possibly, some aspects of geospheric phenomena are, or have been, powered by energy issuing from the sun - either now or in the past - the long-term behavior of such phenomena is ultimately "connected" to long-term changes occurring in the sun itself. Accordingly, the proposed research firstly derives and models a stable surrogate pattern for the long-term solar activity, secondly introduces a transfer-function algorithm for modeling the connection between the surrogate and terrestrial phenomena viewed as partners in the connection, and thirdly probes the connection outcome for episodic or unanticipated effects that may arise due to the fact that in the present context, the connection, should it exist, is very likely nonlinear. Part I of the study presents the theory of the concept, while Part II demonstrates the concept's pertinence to a number of terrestrial phenomena.

    Key words. Solar activity · Kolmogorov algorithm

  13. Personalized translational epilepsy research - Novel approaches and future perspectives: Part II: Experimental and translational approaches.

    Science.gov (United States)

    Bauer, Sebastian; van Alphen, Natascha; Becker, Albert; Chiocchetti, Andreas; Deichmann, Ralf; Deller, Thomas; Freiman, Thomas; Freitag, Christine M; Gehrig, Johannes; Hermsen, Anke M; Jedlicka, Peter; Kell, Christian; Klein, Karl Martin; Knake, Susanne; Kullmann, Dimitri M; Liebner, Stefan; Norwood, Braxton A; Omigie, Diana; Plate, Karlheinz; Reif, Andreas; Reif, Philipp S; Reiss, Yvonne; Roeper, Jochen; Ronellenfitsch, Michael W; Schorge, Stephanie; Schratt, Gerhard; Schwarzacher, Stephan W; Steinbach, Joachim P; Strzelczyk, Adam; Triesch, Jochen; Wagner, Marlies; Walker, Matthew C; von Wegner, Frederic; Rosenow, Felix

    2017-11-01

    Despite the availability of more than 15 new "antiepileptic drugs", the proportion of patients with pharmacoresistant epilepsy has remained constant at about 20-30%. Furthermore, no disease-modifying treatments shown to prevent the development of epilepsy following an initial precipitating brain injury or to reverse established epilepsy have been identified to date. This is likely in part due to the polyetiologic nature of epilepsy, which in turn requires personalized medicine approaches. Recent advances in imaging, pathology, genetics, and epigenetics have led to new pathophysiological concepts and the identification of monogenic causes of epilepsy. In the context of these advances, the First International Symposium on Personalized Translational Epilepsy Research (1st ISymPTER) was held in Frankfurt on September 8, 2016, to discuss novel approaches and future perspectives for personalized translational research. These included new developments and ideas in a range of experimental and clinical areas such as deep phenotyping, quantitative brain imaging, EEG/MEG-based analysis of network dysfunction, tissue-based translational studies, innate immunity mechanisms, microRNA as treatment targets, functional characterization of genetic variants in human cell models and rodent organotypic slice cultures, personalized treatment approaches for monogenic epilepsies, blood-brain barrier dysfunction, therapeutic focal tissue modification, computational modeling for target and biomarker identification, and cost analysis in (monogenic) disease and its treatment. This report on the meeting proceedings is aimed at stimulating much needed investments of time and resources in personalized translational epilepsy research. This Part II includes the experimental and translational approaches and a discussion of the future perspectives, while the diagnostic methods, EEG network analysis, biomarkers, and personalized treatment approaches were addressed in Part I [1]. Copyright © 2017

  14. On the Processing of Spalling Experiments. Part II: Identification of Concrete Fracture Energy in Dynamic Tension

    Science.gov (United States)

    Lukić, Bratislav B.; Saletti, Dominique; Forquin, Pascal

    2017-12-01

    This paper presents a second part of the study aimed at investigating the fracture behavior of concrete under high strain rate tensile loading. The experimental method together with the identified stress-strain response of three tests conducted on ordinary concrete have been presented in the paper entitled Part I (Forquin and Lukić in Journal of Dynamic Behavior of Materials, 2017. https://doi.org/10.1007/s40870-017-0135-1). In the present paper, Part II, the investigation is extended towards directly determining the specific fracture energy of each observed fracture zone by visualizing the dynamic cracking process with a temporal resolution of 1 µs. Having access to temporal displacement fields of the sample surface, it is possible to identify the fracture opening displacement (FOD) and the fracture opening velocity of any principle (open) and secondary (closed) fracture at each measurement instance, that may or may not lead to complete physical failure of the sample. Finally, the local Stress-FOD curves were obtained for each observed fracture zone, opposed to previous works where indirect measurements were used. The obtained results indicated a much lower specific fracture energy compared to the results often found in the literature. Furthermore, numerical simulations were performed with a damage law to evaluate the validity of the proposed experimental data processing and compare it to the most often used one in the previous works. The results showed that the present method can reliably predict the specific fracture energy needed to open one macro-fracture and suggested that indirect measurement techniques can lead to an overestimate of specific fracture energy due to the stringent assumption of linear elasticity up-to the peak and the inability of having access to the real post-peak change of axial stress.

  15. Fractional Programming for Communication Systems—Part II: Uplink Scheduling via Matching

    Science.gov (United States)

    Shen, Kaiming; Yu, Wei

    2018-05-01

    This two-part paper develops novel methodologies for using fractional programming (FP) techniques to design and optimize communication systems. Part I of this paper proposes a new quadratic transform for FP and treats its application for continuous optimization problems. In this Part II of the paper, we study discrete problems, such as those involving user scheduling, which are considerably more difficult to solve. Unlike the continuous problems, discrete or mixed discrete-continuous problems normally cannot be recast as convex problems. In contrast to the common heuristic of relaxing the discrete variables, this work reformulates the original problem in an FP form amenable to distributed combinatorial optimization. The paper illustrates this methodology by tackling the important and challenging problem of uplink coordinated multi-cell user scheduling in wireless cellular systems. Uplink scheduling is more challenging than downlink scheduling, because uplink user scheduling decisions significantly affect the interference pattern in nearby cells. Further, the discrete scheduling variable needs to be optimized jointly with continuous variables such as transmit power levels and beamformers. The main idea of the proposed FP approach is to decouple the interaction among the interfering links, thereby permitting a distributed and joint optimization of the discrete and continuous variables with provable convergence. The paper shows that the well-known weighted minimum mean-square-error (WMMSE) algorithm can also be derived from a particular use of FP; but our proposed FP-based method significantly outperforms WMMSE when discrete user scheduling variables are involved, both in term of run-time efficiency and optimizing results.

  16. Sludge in the pulp and paper industry in Sweden, part II[Combustion of]; Slam fraan skogsindustrin, fas II

    Energy Technology Data Exchange (ETDEWEB)

    Gyllenhammar, Marianne; Herstad Svaerd, Solvie; Kjoerk, Anders; Larsson, Sara; Wennberg, Olle [S.E.P. Scandinavian Energy Project AB, Goeteborg (Sweden); Aamand, Lars-Erik [Chalmers Univ. of Technology, Goeteborg (Sweden); Eskilsson, David [Swedish National Testing and Research Inst., Boraas (Sweden)

    2003-11-01

    During part II of this research program combustible sludge from the pulp and paper industry has been studied in detail. 560,000 tonnes of sludge per year (calculated as dry sludge) are produced in Sweden. The energy potential in the produced sludge is about 2 TWh/year. Today 1 TWh/year is produced in the pulp and paper mill's own boilers. This means that additional energy can be utilized from this material. An objective of this program has been to decide whether or not there are sludge types which are favourable respectively difficult to combust. By mixing different sludge types, or other waste products, emissions and/or problems during combustion can be minimized. These possibilities have been studied thoroughly in this program. A lot of sludge samples have been studied in laboratory scale at SP and in full-scale at Chalmers 12 MW CFB boiler. As a complement to the practical tests S.E.P. has done research regarding different aspects of sludge as a fuel; for example handling of sludge and regional drying. The results of 40 sintering tests at SP showed that the sintering temperature during combustion of sludge in a fluidised bed, with silica sand as bed material, varied between <850 deg C and >1100 deg C. The evaluation showed that the alkali content in the ash had the largest influence on the sintering temperature. Other factors were less important. During the tests at Chalmers eleven different sludge samples have been combusted together with wood pellets. Initially there were problems with the feeding to the boiler for some of the sludge samples. When the fuel feeding problems were solved the combustion took place without any problems. When sludge is co-combusted together with a 'clean' base fuel such as wood pellets the sulphur-, nitrogen- and chloride contents in the sludge have a large impact on the emissions. The normal way to reduce sulphur dioxide but also hydrogen chloride is to add lime in different positions into and after the boiler. In

  17. Association Between National Board Dental Examination Part II Scores and Comprehensive Examinations at Harvard School of Dental Medicine.

    Science.gov (United States)

    Lee, Min Kyeong; Allareddy, Veerasathpurush; Howell, T Howard; Karimbux, Nadeem Y

    2011-01-01

    Harvard School of Dental Medicine (HSDM) uses a hybrid problem-based approach to teaching in the predoctoral program. The objective structured clinical examination (OSCE) is a formative examination designed to assess the performance of students in the problem-based learning (PBL) curriculum. At HSDM three comprehensive examinations with OSCE components are administered during the third and fourth years of clinical training. The National Board Dental Examination (NBDE) Part II is taken in the final year of the predoctoral program. This study examines the association between the NBDE Part II and the comprehensive exams held at HSDM. Predoctoral students from the HSDM classes of 2005 and 2006 were included in this study. The outcome variable of interest was the scores obtained by students in the NBDE Part II, and the main independent variable of interest was the performance of students in the comprehensive exams (honors, pass, make-up exam to pass). The Mann-Whitney U-test was used to examine the association between the grades obtained in the each of the three comprehensive exams and the NBDE Part II scores. Multivariable linear regression analysis was also used to examine the association between the NBDE Part II scores and the comprehensive exam grades. The effect of potential confounding factors including age, sex, and race/ethnicity was adjusted. The results suggest that students who performed well in the comprehensive exams performed better on the NBDE Part II, even after adjusting for confounding factors. Future studies will examine the long-term impact of PBL on postdoctoral plans and career choices.

  18. Neutronics and thermohydraulics of the reactor C.E.N.E. Part II; Analisis neutronico y termohidraulico del reactor C.E.N.E. Parte II

    Energy Technology Data Exchange (ETDEWEB)

    Caro, R

    1976-07-01

    In this report the analysis of neutronics thermohydraulics and shielding of the 10 HWt swimming pool reactor C.E.N.E is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs.

  19. Multiscale modeling, simulations, and experiments of coating growth on nanofibers. Part II. Deposition

    International Nuclear Information System (INIS)

    Buldum, A.; Clemons, C.B.; Dill, L.H.; Kreider, K.L.; Young, G.W.; Zheng, X.; Evans, E.A.; Zhang, G.; Hariharan, S.I.

    2005-01-01

    This work is Part II of an integrated experimental/modeling investigation of a procedure to coat nanofibers and core-clad nanostructures with thin-film materials using plasma-enhanced physical vapor deposition. In the experimental effort, electrospun polymer nanofibers are coated with aluminum materials under different operating conditions to observe changes in the coating morphology. This procedure begins with the sputtering of the coating material from a target. Part I [J. Appl. Phys. 98, 044303 (2005)] focused on the sputtering aspect and transport of the sputtered material through the reactor. That reactor level model determines the concentration field of the coating material. This field serves as input into the present species transport and deposition model for the region surrounding an individual nanofiber. The interrelationships among processing factors for the transport and deposition are investigated here from a detailed modeling approach that includes the salient physical and chemical phenomena. Solution strategies that couple continuum and atomistic models are used. At the continuum scale, transport dynamics near the nanofiber are described. At the atomic level, molecular dynamics (MD) simulations are used to study the deposition and sputtering mechanisms at the coating surface. Ion kinetic energies and fluxes are passed from the continuum sheath model to the MD simulations. These simulations calculate sputtering and sticking probabilities that in turn are used to calculate parameters for the continuum transport model. The continuum transport model leads to the definition of an evolution equation for the coating-free surface. This equation is solved using boundary perturbation and level set methods to determine the coating morphology as a function of operating conditions

  20. A thermoelectric power generating heat exchanger: Part II – Numerical modeling and optimization

    International Nuclear Information System (INIS)

    Sarhadi, Ali; Bjørk, Rasmus; Lindeburg, Niels; Viereck, Peter; Pryds, Nini

    2016-01-01

    Highlights: • A comprehensive model was developed to optimize the integrated TEG-heat exchanger. • The developed model was validated with the experimental data. • The effect of using different interface materials on the output power was assessed. • The influence of TEG arrangement on the power production was investigated. • Optimized geometrical parameters and proper interface materials were suggested. - Abstract: In Part I of this study, the performance of an experimental integrated thermoelectric generator (TEG)-heat exchanger was presented. In the current study, Part II, the obtained experimental results are compared with those predicted by a finite element (FE) model. In the simulation of the integrated TEG-heat exchanger, the thermal contact resistance between the TEG and the heat exchanger is modeled assuming either an ideal thermal contact or using a combined Cooper–Mikic–Yovanovich (CMY) and parallel plate gap formulation, which takes into account the contact pressure, roughness and hardness of the interface surfaces as well as the air gap thermal resistance at the interface. The combined CMY and parallel plate gap model is then further developed to simulate the thermal contact resistance for the case of an interface material. The numerical results show good agreement with the experimental data with an average deviation of 17% for the case without interface material and 12% in the case of including additional material at the interfaces. The model is then employed to evaluate the power production of the integrated system using different interface materials, including graphite, aluminum (Al), tin (Sn) and lead (Pb) in a form of thin foils. The numerical results show that lead foil at the interface has the best performance, with an improvement in power production of 34% compared to graphite foil. Finally, the model predicts that for a certain flow rate, increasing the parallel TEG channels for the integrated systems with 4, 8, and 12 TEGs

  1. [The external patello-tibial transfixation (EPTT). Part II: Clinical application and results].

    Science.gov (United States)

    Ishaque, B; Gotzen, L; Ziring, E; Petermann, J

    1999-07-01

    In part I of the paper the biomechanical and technical background of the EPTT using the MPT fixator and the indications for this procedure have been described. In part II we report about the clinical application of the EPTT in 67 patients with a wide spectrum of repairs and reconstructions of the extensor mechanism. 48 patients had fresh injuries, 18 of them with severe concomitant knee lesions and 19 patients had neglected rsp. unsuccessfully operated injuries. There were 4 deep infections, two of them related to the MPT fixator. In the patients with uneventful healing the fixator remained in place for 7.3 weeks in average. The clinical, isokinetic and radiological results were reviewed in 17 patients with an average follow-up time of 37.3 months. There were 5 patients with partial patellectomy and tendon reattachment because of lower patella pole comminution and 12 patients with tendon reattachment ruptured at the inferior patella pole or suture repair in midsubstance rupture. The clinical results according to the IKDC score were rated in 3 patients as normal, in 10 patients as nearly normal and in 4 patients as abnormal. This rating was highly dependend on the subjective judgement by the patients who considered their operated knees not as normal as the contralateral knees. From our clinical experiences and results we can derive that the EPTT enables the surgical management of extensor mechanism disruptions with a minimum of internal fixation material and provides a safe protection of the repairs and reconstructions during the healing period. The EPTT allows immediate unrestricted functional rehabilitation and early walking without crutches. Thus the EPTT represents an effective alternative to the patello-tibial cerclage with a wire or synthetic ligaments.

  2. Fiducial marker-based correction for involuntary motion in weight-bearing C-arm CT scanning of knees. II. Experiment

    International Nuclear Information System (INIS)

    Choi, Jang-Hwan; Maier, Andreas; Keil, Andreas; McWalter, Emily J.; Gold, Garry E.; Fahrig, Rebecca; Pal, Saikat; Beaupré, Gary S.

    2014-01-01

    Purpose: A C-arm CT system has been shown to be capable of scanning a single cadaver leg under loaded conditions by virtue of its highly flexible acquisition trajectories. In Part I of this study, using the 4D XCAT-based numerical simulation, the authors predicted that the involuntary motion in the lower body of subjects in weight-bearing positions would seriously degrade image quality and the authors suggested three motion compensation methods by which the reconstructions could be corrected to provide diagnostic image quality. Here, the authors demonstrate that a flat-panel angiography system is appropriate for scanning both legs of subjectsin vivo under weight-bearing conditions and further evaluate the three motion-correction algorithms using in vivo data. Methods: The geometry of a C-arm CT system for a horizontal scan trajectory was calibrated using the PDS-2 phantom. The authors acquired images of two healthy volunteers while lying supine on a table, standing, and squatting at several knee flexion angles. In order to identify the involuntary motion of the lower body, nine 1-mm-diameter tantalum fiducial markers were attached around the knee. The static mean marker position in 3D, a reference for motion compensation, was estimated by back-projecting detected markers in multiple projections using calibrated projection matrices and identifying the intersection points in 3D of the back-projected rays. Motion was corrected using three different methods (described in detail previously): (1) 2D projection shifting, (2) 2D deformable projection warping, and (3) 3D rigid body warping. For quantitative image quality analysis, SSIM indices for the three methods were compared using the supine data as a ground truth. Results: A 2D Euclidean distance-based metric of subjects’ motion ranged from 0.85 mm (±0.49 mm) to 3.82 mm (±2.91 mm) (corresponding to 2.76 to 12.41 pixels) resulting in severe motion artifacts in 3D reconstructions. Shifting in 2D, 2D warping, and 3D

  3. Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure . Part II; Severe Damage

    Science.gov (United States)

    Przekop, Adam; Jegley, Dawn C.; Lovejoy, Andrew E.; Rouse, Marshall; Wu, Hsi-Yung T.

    2016-01-01

    The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses a finite element analysis and the testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part II of the paper considers the final test to failure of the test article in the presence of an intentionally inflicted severe discrete source damage under the wing up-bending loading condition. Finite element analysis results are compared with measurements acquired during the test and demonstrate that the hybrid wing body test article was able to redistribute and support the required design loads in a severely damaged condition.

  4. Stochastic theory of nonequilibrium steady states. Part II: Applications in chemical biophysics

    International Nuclear Information System (INIS)

    Ge Hao; Qian Min; Qian Hong

    2012-01-01

    The mathematical theory of nonequilibrium steady state (NESS) has a natural application in open biochemical systems which have sustained source(s) and sink(s) in terms of a difference in their chemical potentials. After a brief introduction in Section , in Part II of this review, we present the widely studied biochemical enzyme kinetics, the workhorse of biochemical dynamic modeling, in terms of the theory of NESS (Section ). We then show that several phenomena in enzyme kinetics, including a newly discovered activation–inhibition switching (Section ) and the well-known non-Michaelis–Menten-cooperativity (Section ) and kinetic proofreading (Section ), are all consequences of the NESS of driven biochemical systems with associated cycle fluxes. Section is focused on nonlinear and nonequilibrium systems of biochemical reactions. We use the phosphorylation–dephosphorylation cycle (PdPC), one of the most important biochemical signaling networks, as an example (Section ). It starts with a brief introduction of the Delbrück–Gillespie process approach to mesoscopic biochemical kinetics (Sections ). We shall discuss the zeroth-order ultrasensitivity of PdPC in terms of a new concept — the temporal cooperativity (Sections ), as well as PdPC with feedback which leads to biochemical nonlinear bistability (Section ). Also, both are nonequilibrium phenomena. PdPC with a nonlinear feedback is kinetically isomorphic to a self-regulating gene expression network, hence the theory of NESS discussed here could have wide applications to many other biochemical systems.

  5. Reproduction in the space environment: Part II. Concerns for human reproduction

    Science.gov (United States)

    Jennings, R. T.; Santy, P. A.

    1990-01-01

    Long-duration space flight and eventual colonization of our solar system will require successful control of reproductive function and a thorough understanding of factors unique to space flight and their impact on gynecologic and obstetric parameters. Part II of this paper examines the specific environmental factors associated with space flight and the implications for human reproduction. Space environmental hazards discussed include radiation, alteration in atmospheric pressure and breathing gas partial pressures, prolonged toxicological exposure, and microgravity. The effects of countermeasures necessary to reduce cardiovascular deconditioning, calcium loss, muscle wasting, and neurovestibular problems are also considered. In addition, the impact of microgravity on male fertility and gamete quality is explored. Due to current constraints, human pregnancy is now contraindicated for space flight. However, a program to explore effective countermeasures to current constraints and develop the required health care delivery capability for extended-duration space flight is suggested. A program of Earth- and space-based research to provide further answers to reproductive questions is suggested.

  6. Start II, red ink, and Boris Yeltsin

    International Nuclear Information System (INIS)

    Arbatov, A.

    1993-01-01

    Apart from the vulnerability implied by the START II treaty, it will bear the burden of the general political opposition to the Yeltsin administration. START II will be seen as part of an overall Yeltsin-Andrei Kozyrev foreign policy that is under fire for selling out Russian national interests in Yugoslavia, the Persian Gulf, and elsewhere. This article discusses public opinion concerning START II, the cost of its implementation, and the general purpose of the treaty

  7. Coordinator(a) de Servicios Clinicos. Parte I (Unidad I-IV). Parte II (Unidad V-VI). Guia. Documento de Trabajo (Clinical Services Coordinator. Part I. Units I-IV. Part II. Units V-VI. Guide. Working Document).

    Science.gov (United States)

    Puerto Rico State Dept. of Education, Hato Rey. Area for Vocational and Technical Education.

    This guide is intended for instructing secondary students in the occupation of clinical services coordinator in a hospital. The first part contains four units on the following subjects: the occupation of clinical services coordinator; interpersonal relationships; ethical/legal aspects; and communications (telephone, intercom, and others). For each…

  8. Grease lubrication in rolling bearings

    CERN Document Server

    Lugt, Piet M

    2012-01-01

    The definitive book on the science of grease lubrication for roller and needle bearings in industrial and vehicle engineering. Grease Lubrication in Rolling Bearings provides an overview of the existing knowledge on the various aspects of grease lubrication (including lubrication systems) and the state of the art models that exist today. The book reviews the physical and chemical aspects of grease lubrication, primarily directed towards lubrication of rolling bearings. The first part of the book covers grease composition, properties and rheology, including thermal

  9. Towards multi-resolution global climate modeling with ECHAM6-FESOM. Part II: climate variability

    Science.gov (United States)

    Rackow, T.; Goessling, H. F.; Jung, T.; Sidorenko, D.; Semmler, T.; Barbi, D.; Handorf, D.

    2018-04-01

    This study forms part II of two papers describing ECHAM6-FESOM, a newly established global climate model with a unique multi-resolution sea ice-ocean component. While part I deals with the model description and the mean climate state, here we examine the internal climate variability of the model under constant present-day (1990) conditions. We (1) assess the internal variations in the model in terms of objective variability performance indices, (2) analyze variations in global mean surface temperature and put them in context to variations in the observed record, with particular emphasis on the recent warming slowdown, (3) analyze and validate the most common atmospheric and oceanic variability patterns, (4) diagnose the potential predictability of various climate indices, and (5) put the multi-resolution approach to the test by comparing two setups that differ only in oceanic resolution in the equatorial belt, where one ocean mesh keeps the coarse 1° resolution applied in the adjacent open-ocean regions and the other mesh is gradually refined to 0.25°. Objective variability performance indices show that, in the considered setups, ECHAM6-FESOM performs overall favourably compared to five well-established climate models. Internal variations of the global mean surface temperature in the model are consistent with observed fluctuations and suggest that the recent warming slowdown can be explained as a once-in-one-hundred-years event caused by internal climate variability; periods of strong cooling in the model (`hiatus' analogs) are mainly associated with ENSO-related variability and to a lesser degree also to PDO shifts, with the AMO playing a minor role. Common atmospheric and oceanic variability patterns are simulated largely consistent with their real counterparts. Typical deficits also found in other models at similar resolutions remain, in particular too weak non-seasonal variability of SSTs over large parts of the ocean and episodic periods of almost absent

  10. Stress Analysis and Fatigue Behaviour of PTFE-Bronze Layered Journal Bearing under Real-Time Dynamic Loading

    Science.gov (United States)

    Duman, M. S.; Kaplan, E.; Cuvalcı, O.

    2018-01-01

    The present paper is based on experimental studies and numerical simulations on the surface fatigue failure of the PTFE-bronze layered journal bearings under real-time loading. ‘Permaglide Plain Bearings P10’ type journal bearings were experimentally tested under different real time dynamic loadings by using real time journal bearing test system in our laboratory. The journal bearing consists of a PTFE-bronze layer approximately 0.32 mm thick on the steel support layer with 2.18 mm thick. Two different approaches have been considered with in experiments: (i) under real- time constant loading with varying bearing widths, (ii) under different real-time loadings at constant bearing widths. Fatigue regions, micro-crack dispersion and stress distributions occurred at the journal bearing were experimentally and theoretically investigated. The relation between fatigue region and pressure distributions were investigated by determining the circumferential pressure distribution under real-time dynamic loadings for the position of every 10° crank angles. In the theoretical part; stress and deformation distributions at the surface of the journal bearing analysed by using finite element methods to determine the relationship between stress and fatigue behaviour. As a result of this study, the maximum oil pressure and fatigue cracks were observed in the most heavily loaded regions of the bearing surface. Experimental results show that PTFE-Bronze layered journal bearings fatigue behaviour is better than the bearings include white metal alloy.

  11. Tratamento sistêmico da psoríase - Parte II: Imunomoduladores biológicos Systemic treatment of psoriasis - Part II: Biologic immunomodulator agents

    Directory of Open Access Journals (Sweden)

    Lúcia Arruda

    2004-08-01

    Full Text Available Em continuidade ao capítulo da edição anterior dos Anais Brasileiros de Dermatologia, nesta segunda parte da EMC-D serão discutidas as novas drogas, os imunomoduladores biológicos, que agem em determinadas fases da imunopatogênese da doença, modificando fenotipicamente sua evolução. Também serão discutidos alguns aspectos imunológicos que, atualmente, são responsáveis pelo desencadeamento da doençaAs part of its continued studies of psoriasis, this second part of the Continuing Medical Education in Dermatology segment of the Anais Brasileiros de Dermatologia introduces biological immunomodulators. Also known as "biologics", these drugs act on the immunopathogenetic steps of psoriasis by changing its features and progression. This paper also reviews some of the immunologic aspects of psoriasis.

  12. Developing guidelines for economic evaluation of environmental impacts in EIAs. Part II: Case studies and dose-response literature

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    This Part II of the report contains full versions of the case studies for air, water and land (Chapters 2-4), which were only summarised in Part I. In addition, during the work the research team has collected a large amount of literature and information on dose response relationships for air and water pollution relevant to China. This information is included as Chapters 5 and 6.

  13. Developing guidelines for economic evaluation of environmental impacts in EIAs. Part II: Case studies and dose-response literature

    International Nuclear Information System (INIS)

    2005-01-01

    This Part II of the report contains full versions of the case studies for air, water and land (Chapters 2-4), which were only summarised in Part I. In addition, during the work the research team has collected a large amount of literature and information on dose response relationships for air and water pollution relevant to China. This information is included as Chapters 5 and 6

  14. Acuity and case management: a healthy dose of outcomes, part II.

    Science.gov (United States)

    Craig, Kathy; Huber, Diane L

    2007-01-01

    This is the second of a 3-part series presenting 2 effective applications-acuity and dosage-that describe how the business case for case management (CM) can be made. In Part I, dosage and acuity concepts were explained as client need-severity, CM intervention-intensity, and CM activity-dose prescribed by amount, frequency, duration, and breadth of activities. Part I also featured a specific exemplar, the CM Acuity Tool, and described how to use acuity to identify and score the complexity of a CM case. Appropriate dosage prescription of CM activity was discussed. Part II further explains dosage and presents two acuity instruments, the Acuity Tool and AccuDiff. Details are provided that show how these applications produce opportunities for better communication about CM cases and for more accurate measurement of the right content that genuinely reflects the essentials of CM practice. The information contained in the 3-part series applies to all CM practice settings and contains ideas and recommendations useful to CM generalists, specialists, and supervisors, plus business and outcomes managers. The Acuity Tools Project was developed from frontline CM practice in one large, national telephonic CM company. Dosage: A literature search failed to find research into dosage of a behavioral intervention. The Huber-Hall model was developed and tested in a longitudinal study of CM models in substance abuse treatment and reported in the literature. Acuity: A structured literature search and needs assessment launched the development of the suite of acuity tools. A gap analysis identified that an instrument to assign and measure case acuity specific to CM activities was needed. Clinical experts, quality specialists, and business analysts (n = 7) monitored the development and testing of the tools, acuity concepts, scores, differentials, and their operating principles and evaluated the validity of the Acuity Tools' content related to CM activities. During the pilot phase of

  15. The Historiography of British Imperial Education Policy, Part II: Africa and the Rest of the Colonial Empire

    Science.gov (United States)

    Whitehead, Clive

    2005-01-01

    Part II of this historiographical study examines British education policy in Africa, and in the many crown colonies, protectorates, and mandated territories around the globe. Up until 1920, the British government took far less interest than in India, in the development of schooling in Africa and the rest of the colonial empire, and education was…

  16. RA reactor safety analysis, Part II - Accident analysis; Analiza sigurnosti rada Reaktora RA I-III, Deo II - Analiza akcidenta

    Energy Technology Data Exchange (ETDEWEB)

    Raisic, N; Radanovic, Lj; Milovanovic, M; Afgan, N; Kulundzic, P [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

    1963-02-15

    This part of the RA reactor safety analysis includes analysis of possible accidents caused by failures of the reactor devices and errors during reactor operation. Two types of accidents are analyzed: accidents resulting from uncontrolled reactivity increase, and accidents caused by interruption of cooling.

  17. Industry Wage Surveys: Banking and Life Insurance, December 1976. Part I--Banking. Part II--Life Insurance. Bulletin 1988.

    Science.gov (United States)

    Barsky, Carl

    This report presents the results of a survey conducted by the Bureau of Labor Statistics to determine wages and related benefits in (1) the banking industry and (2) for employees in home offices and regional head offices of life insurance carriers. Part 1 discusses banking industry characteristics and presents data for tellers and selected…

  18. Study of diffuse H II regions potentially forming part of the gas streams around Sgr A*

    Science.gov (United States)

    Armijos-Abendaño, J.; López, E.; Martín-Pintado, J.; Báez-Rubio, A.; Aravena, M.; Requena-Torres, M. A.; Martín, S.; Llerena, M.; Aldás, F.; Logan, C.; Rodríguez-Franco, A.

    2018-05-01

    We present a study of diffuse extended ionized gas towards three clouds located in the Galactic Centre (GC). One line of sight (LOS) is towards the 20 km s-1 cloud (LOS-0.11) in the Sgr A region, another LOS is towards the 50 km s-1 cloud (LOS-0.02), also in Sgr A, while the third is towards the Sgr B2 cloud (LOS+0.693). The emission from the ionized gas is detected from Hnα and Hmβ radio recombination lines (RRLs). Henα and Hemβ RRL emission is detected with the same n and m as those from the hydrogen RRLs only towards LOS+0.693. RRLs probe gas with positive and negative velocities towards the two Sgr A sources. The Hmβ to Hnα ratios reveal that the ionized gas is emitted under local thermodynamic equilibrium conditions in these regions. We find a He to H mass fraction of 0.29±0.01 consistent with the typical GC value, supporting the idea that massive stars have increased the He abundance compared to its primordial value. Physical properties are derived for the studied sources. We propose that the negative velocity component of both Sgr A sources is part of gas streams considered previously to model the GC cloud kinematics. Associated massive stars with what are presumably the closest H II regions to LOS-0.11 (positive velocity gas), LOS-0.02, and LOS+0.693 could be the main sources of ultraviolet photons ionizing the gas. The negative velocity components of both Sgr A sources might be ionized by the same massive stars, but only if they are in the same gas stream.

  19. Quality control of outpatient imaging examinations in North Rhine-Westphalia. Part II

    International Nuclear Information System (INIS)

    Krug, B.; Boettge, M.; Zaehringer, M.; Reinecke, T.; Coburger, S.; Harnischmacher, U.; Luengen, M.; Lauterbach, K.W.; Lehmacher, W.; Lackner, K.

    2003-01-01

    Purpose: In the state of North Rhine-Westphalia (NRW), Germany, a survey was conducted on radiologic examinations ordered by general practitioners (GPs). Part II of this study aims to determine the quality of the process and outcome. The reference standard is the assessment of both radiologists and physicians without board certification in radiology working at a university hospital and in outpatient facilities. Materials and Methods: All GPs in NRW were asked to cooperate. Participating GPs filled out a questionnaire for each patient. The patients recorded the symptoms prompting the imaging examinations. The radiologists or other physicians performing the examinations were asked to provide the images and written reports and to complete a questionnaire. A file was created for each of the 394 patients with image documentation of at least one examination. Each file, which included medical history, physical findings, imaging documentation and written report, was sequentially forwarded to a board-certified radiologist and to a physician without board certification in radiology working in a university hospital and in an outpatient facility. All physicians were requested to complete a structured questionnaire for each file. Results: The referral diagnoses were rated as medically plausible in 81%, the indications for imaging found correct in 76%, the examination techniques considered appropriate in 69%, the clinical question answered in 63%, the interpretation judged medically correct in 50% and all incidental findings documented in 49%. In retrospect, 32% of the examinations were judged superfluous. The sequence of multiple examinations performed on a particular patient was rated as appropriate in 51%. The interpretation revealed specialty-related differences. The plausibility of the referral diagnoses had a significant impact on the appropriateness of subsequent diagnostic investigations. Marked deficits showed sonography, performance by non-radiologists, self

  20. [Verrucous pastern dermatitis syndrome in heavy draught horses. Part II: Clinical findings].

    Science.gov (United States)

    Geburek, F; Deegen, E; Hewicker-Trautwein, M; Ohnesorge, B

    2005-07-01

    In the present field study the skin of the feet of 37 heavy draught horses of different breeds showing verrucous pastern dermatitis was examined clinically. Included were the degree of severity of the disease and the prevalence of anatomically normal structures associated with the skin: fetlock tufts of hair ("feathering"), ergots, chestnuts, bulges in the pastern region, cannon circumference. Each horse was examined for Chorioptes sp. skin mites. Information was also collected on the development of the skin alterations and housing conditions and feeding. These individual data were correlated with the clinical degree of severity of verrucous pastern dermatitis, which was evaluated using a numerical code (scoring system). In addition, punch biopsies were taken from the diseased skin of the feet and from healthy skin of the neck for comparative patho-histological examination (see Part III). Verrucous pastern dermatitis is a chronic disease which can be divided into four groups: scaling (group I), hyperkeratotic and hyperplastic plaque-like lesions (group II), tuberous skin masses (group III), and verrucous skin lesions with rugged surfaces (group IV). No correlation was found between the clinical degree of severity of the skin lesions and sex, breed, amount of work, use of stallions for breeding, grooming condition of the hair, white markings in the foot region, or Chorioptes sp. infestation. In regard to feeding it was found that the amount of maize and oats fed had some influence on the clinical degree of severity. Statistical analysis revealed a significant correlation between the clinical degree of severity and the age, the grooming condition of the hooves, and the mean cannon circumference. The prevalence of fetlock tufts of hair, chestnuts, ergots, and anatomically normal bulges in the pastern region also increased significantly with the clinical degree of severity. Furthermore the study revealed that the clinical degree of severity depended on the hygienic

  1. Notes on the Birds of Central Oaxaca, Part II: Columbidae to Vireonidae

    Directory of Open Access Journals (Sweden)

    John M. Forcey

    2015-06-01

    Full Text Available Notas sobre las aves de Oaxaca central, parte II: Columbidae a Vireonidae Se reportan  nuevos datos que amplían y clarifican nuestro conocimiento del estatus y distribución de 70 especies de aves en la región central del Estado de Oaxaca. Las observaciones se realizaron abarcando partes de los distritos de Etla, Ixtlan, Tlacolula, y Zaachila, dentro de un círculo de radio de 35 km alrededor de la Ciudad de Oaxaca. El reporte se basa en observaciones tomadas durante 738 días, comprendidos entre diciembre 1996 y marzo 2002. Los hábitats principalmente visitados fueron pino-encino (incluyendo zonas pequeñas de pino-encino-oyamel y pino-encino mezclado con pastizales, matorral de encino, matorral subtropical, vegetación riparia, y vegetación secundaria, campos agrícolas y otros (incluyendo áreas urbanas, como jardines y parques. Las siguientes especies se reportan por primera vez en la zona: Heliomaster constantii, Tilmatura dupontii, Empidonax flaviventris, Empidonax virescens, Myiarchus crinitus, Myiodynastes luteiventris, Vireo philadelphicus, Vireo olivaceus y Vireo flavoviridis. Además, las siguientes diez especies se han reportado anteriormente una sola vez o solamente en los Conteos Navideños: Caprimulgus ridgwayi (residente,Panyptila sanctihieronymi (residente local, Amazilia cyanocephala (residente local, Amazilia viridifrons, Lamprolaima rhami, Momotus mexicanus (residente en la Sierra Juárez, Sayornis phoebe, Myiozetetes similis (residente, Pachyramphus major (residente y Vireo griseus. Se reportan datos de la reproducción de 25 especies, 18 de las cuales no se habían registrado como reproduciéndose en la zona antes. De estos, 24 se pueden agrupar como reproduciéndose en los meses de abril a julio, y 17 se reproducen en zonas riparias, seis de ellos casi exclusivamente.

  2. A primer of drug safety surveillance: an industry perspective. Part II: Product labeling and product knowledge.

    Science.gov (United States)

    Allan, M C

    1992-01-01

    To place the fundamentals of clinical drug safety surveillance in a conceptual framework that will facilitate understanding and application of adverse drug event data to protect the health of the public and support a market for pharmaceutical manufacturers' products. Part II of this series discusses specific issues regarding product labeling, such as developing the labeling, changing the labeling, and the legal as well as commercial ramifications of the contents of the labeling. An adverse event report scenario is further analyzed and suggestions are offered for maintaining the product labeling as an accurate reflection of the drug safety surveillance data. This article also emphasizes the necessity of product knowledge in adverse event database management. Both scientific and proprietary knowledge are required. Acquiring product knowledge is a part of the day-to-day activities of drug safety surveillance. A knowledge of the history of the product may forestall adverse publicity, as shown in the illustration. This review uses primary sources from the federal laws (regulations), commentaries, and summaries. Very complex topics are briefly summarized in the text. Secondary sources, ranging from newspaper articles to judicial summaries, illustrate the interpretation of adverse drug events and opportunities for drug safety surveillance intervention. The reference materials used were articles theoretically or practically applicable in the day-to-day practice of drug safety surveillance. The role of clinical drug safety surveillance in product monitoring and drug development is described. The process of drug safety surveillance is defined by the Food and Drug Administration regulations, product labeling, product knowledge, and database management. Database management is subdivided into the functions of receipt, retention, retrieval, and review of adverse event reports. Emphasis is placed on the dynamic interaction of the components of the process. Suggestions are offered

  3. The 183-WSL Fast Rain Rate Retrieval Algorithm. Part II: Validation Using Ground Radar Measurements

    Science.gov (United States)

    Laviola, Sante; Levizzani, Vincenzo

    2014-01-01

    The Water vapour Strong Lines at 183 GHz (183-WSL) algorithm is a method for the retrieval of rain rates and precipitation type classification (convectivestratiform), that makes use of the water vapor absorption lines centered at 183.31 GHz of the Advanced Microwave Sounding Unit module B (AMSU-B) and of the Microwave Humidity Sounder (MHS) flying on NOAA-15-18 and NOAA-19Metop-A satellite series, respectively. The characteristics of this algorithm were described in Part I of this paper together with comparisons against analogous precipitation products. The focus of Part II is the analysis of the performance of the 183-WSL technique based on surface radar measurements. The ground truth dataset consists of 2.5 years of rainfall intensity fields from the NIMROD European radar network which covers North-Western Europe. The investigation of the 183-WSL retrieval performance is based on a twofold approach: 1) the dichotomous statistic is used to evaluate the capabilities of the method to identify rain and no-rain clouds; 2) the accuracy statistic is applied to quantify the errors in the estimation of rain rates.The results reveal that the 183-WSL technique shows good skills in the detection of rainno-rain areas and in the quantification of rain rate intensities. The categorical analysis shows annual values of the POD, FAR and HK indices varying in the range 0.80-0.82, 0.330.36 and 0.39-0.46, respectively. The RMSE value is 2.8 millimeters per hour for the whole period despite an overestimation in the retrieved rain rates. Of note is the distribution of the 183-WSL monthly mean rain rate with respect to radar: the seasonal fluctuations of the average rainfalls measured by radar are reproduced by the 183-WSL. However, the retrieval method appears to suffer for the winter seasonal conditions especially when the soil is partially frozen and the surface emissivity drastically changes. This fact is verified observing the discrepancy distribution diagrams where2the 183-WSL

  4. Superconducting bearings for flywheel applications

    Energy Technology Data Exchange (ETDEWEB)

    Abrahamsen, Asger Bech

    2001-05-01

    A literature study on the application of superconducting bearings in energy storage flywheel systems. The physics of magnetic levitation and superconductors are presented in the first part of the report, followed by a discussion of the literature found on the applications of superconducting bearings in flywheels. (au)

  5. Superconducting bearings for flywheel applications

    DEFF Research Database (Denmark)

    Abrahamsen, A.B.

    2001-01-01

    A literature study on the application of superconducting bearings in energy storage flywheel systems. The physics of magnetic levitation and superconductors are presented in the first part of the report, followed by a discussion of the literature found onthe applications of superconducting bearings...

  6. A Study of Active Rotor-Blade Vibration Control using Electro-Magnetic Actuation - Part II: Experiment

    DEFF Research Database (Denmark)

    Christensen, Rene Hardam; Santos, Ilmar

    2004-01-01

    . The remaining two sets of actuators are applied to act directly onto the hub, working as an active radial bearing controlling the rotor lateral movement. The rig is equipped with sensors measuring blade and rotor vibrations. Actuators and sensors are connected to a digital signal processor running the control......This is the second paper in a two-part study on active rotor-blade vibration control. This part presents an experimental contribution into the work of active controller design for rotor-blade systems. The primary aim is to give an experimental validation and show the applicability...... algorithm. Measurement signals and actuator control signals from the sensors and actuators fixed in the rotating disc are transmitted to the control unit through a slip-ring device. Various measured responses of both the controlled and the non-controlled system with identical blades and with deliberately...

  7. Control of uncertain systems by feedback linearization with neural networks augmentation. Part II. Controller validation by numerical simulation

    Directory of Open Access Journals (Sweden)

    Adrian TOADER

    2010-09-01

    Full Text Available The paper was conceived in two parts. Part I, previously published in this journal, highlighted the main steps of adaptive output feedback control for non-affine uncertain systems, having a known relative degree. The main paradigm of this approach was the feedback linearization (dynamic inversion with neural network augmentation. Meanwhile, based on new contributions of the authors, a new paradigm, that of robust servomechanism problem solution, has been added to the controller architecture. The current Part II of the paper presents the validation of the controller hereby obtained by using the longitudinal channel of a hovering VTOL-type aircraft as mathematical model.

  8. Uncertainty estimation with a small number of measurements, part II: a redefinition of uncertainty and an estimator method

    Science.gov (United States)

    Huang, Hening

    2018-01-01

    This paper is the second (Part II) in a series of two papers (Part I and Part II). Part I has quantitatively discussed the fundamental limitations of the t-interval method for uncertainty estimation with a small number of measurements. This paper (Part II) reveals that the t-interval is an ‘exact’ answer to a wrong question; it is actually misused in uncertainty estimation. This paper proposes a redefinition of uncertainty, based on the classical theory of errors and the theory of point estimation, and a modification of the conventional approach to estimating measurement uncertainty. It also presents an asymptotic procedure for estimating the z-interval. The proposed modification is to replace the t-based uncertainty with an uncertainty estimator (mean- or median-unbiased). The uncertainty estimator method is an approximate answer to the right question to uncertainty estimation. The modified approach provides realistic estimates of uncertainty, regardless of whether the population standard deviation is known or unknown, or if the sample size is small or large. As an application example of the modified approach, this paper presents a resolution to the Du-Yang paradox (i.e. Paradox 2), one of the three paradoxes caused by the misuse of the t-interval in uncertainty estimation.

  9. Hydrodynamic bearings

    CERN Document Server

    Bonneau, Dominique; Souchet, Dominique

    2014-01-01

    This Series provides the necessary elements to the development and validation of numerical prediction models for hydrodynamic bearings. This book describes the rheological models and the equations of lubrication. It also presents the numerical approaches used to solve the above equations by finite differences, finite volumes and finite elements methods.

  10. Delayed child-bearing.

    Science.gov (United States)

    Johnson, Jo-Ann; Tough, Suzanne

    2012-01-01

    compensate for age-related decline in fertility. (II-2A) 2. A fertility evaluation should be initiated after 6 months of unprotected intercourse without conception in women 35 to 37 years of age, and earlier in women > 37 years of age. (II-2A) 3. Prospective parents should be informed that semen quality and male fertility deteriorate with advancing age and that the risk of genetic disorders in offspring increases. (II-2A) 4. Women ≥ 35 years of age should be offered screening for fetal aneuploidy and undergo a detailed second trimester ultrasound examination to look for significant fetal birth defects (particularly cardiac defects). (II-1A) 5. Delayed child-bearing is associated with increased obstetrical and perinatal complications. Care providers need to be aware of these complications and adjust obstetrical management protocols to ensure optimal maternal and perinatal outcomes. (II-2A) 6. All adults of reproductive age should be aware of the obstetrical and perinatal risks of advanced maternal age so they can make informed decisions about the timing of child-bearing. (II-2A) 7. Strategies to improve informed decision-making by prospective parents should be designed, implemented, and evaluated. These strategies should provide opportunity for adults to understand the potential medical, social, and economic consequences of child-bearing throughout the reproductive years. (III-B) 8. Barriers to healthy reproduction, including workplace policies, should be reviewed to optimize the likelihood of healthy pregnancies. (III-C).

  11. Nuclear power plant simulators for operator licensing and training. Part I. The need for plant-reference simulators. Part II. The use of plant-reference simulators

    International Nuclear Information System (INIS)

    Rankin, W.L.; Bolton, P.A.; Shikiar, R.; Saari, L.M.

    1984-05-01

    Part I of this report presents technical justification for the use of plant-reference simulators in the licensing and training of nuclear power plant operators and examines alternatives to the use of plant-reference simulators. The technical rationale is based on research on the use of simulators in other industries, psychological learning and testing principles, expert opinion and user opinion. Part II discusses the central considerations in using plant-reference simulators for licensing examination of nuclear power plant operators and for incorporating simulators into nuclear power plant training programs. Recommendations are presented for the administration of simulator examinations in operator licensing that reflect the goal of maximizing both reliability and validity in the examination process. A series of organizational tasks that promote the acceptance, use, and effectiveness of simulator training as part of the onsite training program is delineated

  12. Part I: $\\beta$-delayed fission, laser spectroscopy and shape-coexistence studies with astatine beams; Part II: Delineating the island of deformation in the light gold isotopes by means of laser spectroscopy

    CERN Document Server

    Andreyev, Andrei

    2013-01-01

    Part I: $\\beta$-delayed fission, laser spectroscopy and shape-coexistence studies with astatine beams; Part II: Delineating the island of deformation in the light gold isotopes by means of laser spectroscopy

  13. Treatability study on the Bear Creek Valley characterization area at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Phase II work plan for S-3 site contaminated groundwater interception--in-field media evaluation and groundwater capture methods

    International Nuclear Information System (INIS)

    1996-12-01

    A treatability study is being conducted to support implementation:of early actions at the S-3 Site in the Bear Creek Valley (BCV) Characterization Area (CA). The objectives of the early actions Will be (1) to reduce concentrations of uranium and nitrate in Bear Creek and (2) to reduce contaminants of concern in North Tributary (NT)-1 and NT-2. The BCV CA is located within the US DOE's Oak Ridge Reservation in Tennessee. Hazardous and radioactive materials from the Y-12 Plant operations were, disposed of at various sites within BCV. Groundwater and surface water in the BCV CA have been contaminated. The remedial investigation (RI) for the BCV CA identified that the greatest mass flux of contaminants from the various sources migrates via groundwater at the source and discharges to surface water in Bear Creek and its tributaries. In the RI, the combined discharge from the S-3 Site and the Boneyard/Burnyard (BYBY) was identified as accounting for 75% of the cancer risk and more than 80% of the chemical toxicity to Potential downgradient human receptors. In addition, the S-3 Site has caused degradation of surface water quality in upper Bear Creek and two of its tributaries. The BCV CA treatability study focuses on capture and treatment of shallow groundwater before it discharges to tributary waters. The objectives Of treatment of this groundwater are (1) to reduce the concentrations of uranium and nitrate in NT-1 and Bear Creek such that the concentrations of these chemicals in surface water and groundwater are reduced to acceptable levels, (2) to reduce the concentrations of nitrate and metals, and reduce the overall concentration of total dissolved solids; and (3) to hydraulically contain the plume of contaminated, groundwater that is moving in bedrock in the Nolichucky Shale such that the rate of contaminant discharge will be reduced in the long term. The objective of Phase II is to produce conceptual designs for treatment system configurations

  14. Part I: nonlinear analysis of three coupled Josephson junctions. Part II. general bond-to-site mapping in aggregation

    International Nuclear Information System (INIS)

    Strenski, P.N.

    1985-01-01

    The first part of this thesis deals with the analysis of a small array of Josephson junctions, superconducting devices of markedly nonlinear behavior. The components of the array are modeled as resistively-shunted junctions and are driven by direct current. A chapter is provided that reviews the validity and features of such a model for the case of a single junction. This chapter also includes background information on the subjects of bifurcation, chaos, and fractals. In the following chapters, the array of three junctions is studied, first with one driving current and later with an additional bias current. The analysis includes both numerical results from computer simulations and analytic computations using a perturbative approach. The two approaches are shown to be in good agreement. The behavior of the array is dominated by hysteresis effects. The second part of the thesis describes an exact bound-to-site transformation for diffusion-limited aggregation. A review is provided that summarizes the field of aggregation and demonstrates the need for such exact results. The equivalence maps a class of partial adhesion problems on arbitrary lattices to absolute adhesion problems on transformed lattices. Examples are given for diffusion in the presence and absence of an external field

  15. Modulus of elasticity, creep and shrinkage of concrete, phase II : part 1, creep study, final report.

    Science.gov (United States)

    2009-10-01

    A laboratory testing program was performed to evaluate the physical and mechanical properties of typical Class II, IV, V, and VI concrete mixtures made with a Miami Oolite limestone, a Georgia granite, and a lightweight aggregate Stalite, including c...

  16. Impacts of Realistic Urban Heating. Part II: Air Quality and City Breathability

    Science.gov (United States)

    Nazarian, Negin; Martilli, Alberto; Norford, Leslie; Kleissl, Jan

    2018-03-01

    Urban morphology and inter-building shadowing result in a non-uniform distribution of surface heating in urban areas, which can significantly modify the urban flow and thermal field. In Part I, we found that in an idealized three-dimensional urban array, the spatial distribution of the thermal field is correlated with the orientation of surface heating with respect to the wind direction (i.e. leeward or windward heating), while the dispersion field changes more strongly with the vertical temperature gradient in the street canyon. Here, we evaluate these results more closely and translate them into metrics of "city breathability," with large-eddy simulations coupled with an urban energy-balance model employed for this purpose. First, we quantify breathability by, (i) calculating the pollutant concentration at the pedestrian level (horizontal plane at z≈ 1.5 -2 m) and averaged over the canopy, and (ii) examining the air exchange rate at the horizontal and vertical ventilating faces of the canyon, such that the in-canopy pollutant advection is distinguished from the vertical removal of pollution. Next, we quantify the change in breathability metrics as a function of previously defined buoyancy parameters, horizontal and vertical Richardson numbers (Ri_h and Ri_v , respectively), which characterize realistic surface heating. We find that, unlike the analysis of airflow and thermal fields, consideration of the realistic heating distribution is not crucial in the analysis of city breathability, as the pollutant concentration is mainly correlated with the vertical temperature gradient (Ri_v ) as opposed to the horizontal (Ri_h ) or bulk (Ri_b ) thermal forcing. Additionally, we observe that, due to the formation of the primary vortex, the air exchange rate at the roof level (the horizontal ventilating faces of the building canyon) is dominated by the mean flow. Lastly, since Ri_h and Ri_v depend on the meteorological factors (ambient air temperature, wind speed, and

  17. Peak-summer East Asian rainfall predictability and prediction part II: extratropical East Asia

    Science.gov (United States)

    Yim, So-Young; Wang, Bin; Xing, Wen

    2016-07-01

    The part II of the present study focuses on northern East Asia (NEA: 26°N-50°N, 100°-140°E), exploring the source and limit of the predictability of the peak summer (July-August) rainfall. Prediction of NEA peak summer rainfall is extremely challenging because of the exposure of the NEA to midlatitude influence. By examining four coupled climate models' multi-model ensemble (MME) hindcast during 1979-2010, we found that the domain-averaged MME temporal correlation coefficient (TCC) skill is only 0.13. It is unclear whether the dynamical models' poor skills are due to limited predictability of the peak-summer NEA rainfall. In the present study we attempted to address this issue by applying predictable mode analysis method using 35-year observations (1979-2013). Four empirical orthogonal modes of variability and associated major potential sources of variability are identified: (a) an equatorial western Pacific (EWP)-NEA teleconnection driven by EWP sea surface temperature (SST) anomalies, (b) a western Pacific subtropical high and Indo-Pacific dipole SST feedback mode, (c) a central Pacific-El Nino-Southern Oscillation mode, and (d) a Eurasian wave train pattern. Physically meaningful predictors for each principal component (PC) were selected based on analysis of the lead-lag correlations with the persistent and tendency fields of SST and sea-level pressure from March to June. A suite of physical-empirical (P-E) models is established to predict the four leading PCs. The peak summer rainfall anomaly pattern is then objectively predicted by using the predicted PCs and the corresponding observed spatial patterns. A 35-year cross-validated hindcast over the NEA yields a domain-averaged TCC skill of 0.36, which is significantly higher than the MME dynamical hindcast (0.13). The estimated maximum potential attainable TCC skill averaged over the entire domain is around 0.61, suggesting that the current dynamical prediction models may have large rooms to improve

  18. Market Analysis and Consumer Impacts Source Document. Part II. Review of Motor Vehicle Market and Consumer Expenditures on Motor Vehicle Transportation

    Science.gov (United States)

    1980-12-01

    This source document on motor vehicle market analysis and consumer impacts consists of three parts. Part II consists of studies and review on: motor vehicle sales trends; motor vehicle fleet life and fleet composition; car buying patterns of the busi...

  19. Propriedades termofísicas de soluções-modelo similares a sucos: parte II Thermophysical properties of model solutions similar to juice: part II

    Directory of Open Access Journals (Sweden)

    Sílvia Cristina Sobottka Rolim de Moura

    2005-09-01

    Full Text Available Propriedades termofísicas, densidade e viscosidade de soluções-modelo similares a sucos foram determinadas experimentalmente. Os resultados foram comparados aos preditos por modelos matemáticos (STATISTICA 6.0 e obtidos da literatura em função da sua composição química. Para definição das soluções-modelo, foi realizado um planejamento estrela, mantendo-se fixa a quanti-dade de ácido (1,5% e variando-se a água (82-98,5%, o carboidrato (0-15% e a gordura (0-1,5%. A densidade foi determinada em picnômetro. A viscosidade foi determinada em viscosímetro Brookfield modelo LVF. A condutividade térmica foi calculada com o conhecimento das propriedades difusividade térmica e calor específico (apresentados na Parte I deste trabalho MOURA [7] e da densidade. Os resultados de cada propriedade foram analisados através de superfícies de respostas. Foram encontrados resultados significativos para as propriedades, mostrando que os modelos encontrados representam as mudanças das propriedades térmicas e físicas dos sucos, com alterações na composição e na temperatura.Thermophysical properties, density and viscosity of model solutions similar to juices were experimentally determined. The results were compared to those predicted by mathematical models (STATISTIC 6.0 and to values mentioned in the literature, according to the chemical composition. A star planning was adopted to define model solutions composition; fixing the acid amount in 1.5% and varying water (82-98.5%, carbohydrate (0-15% and fat (0-1.5%. The density was determined by picnometer. The viscosity was determined by Brookfield LVF model viscosimeter. The thermal conductivity was calculated based on thermal diffusivity and specific heat values (presented at the 1st . Part of this paper - MOURA [7] and density. The results of each property were analyzed by the response surface method. The found results were significant, indicating that the models represent the changes of

  20. Part I. Inviscid, swirling flows and vortex breakdown. Part II. A numerical investigation of the Lundgren turbulence model

    International Nuclear Information System (INIS)

    Buntine, J.D.

    1994-01-01

    Part I. A study of the behaviour of an inviscid, swirling fluid is performed. This flow can be described by the Squire-Long equation if the constraints of time-independence and axisymmetry are invoked. The particular case of flow through a diverging pipe is selected and a study is conducted to determine over what range of parameters does a solution exist. The work is performed with a view to understanding how the phenomenon of vortex breakdown develops. Experiments and previous numerical studies have indicated that the flow is sensitive to boundary conditions particularly at the pipe inlet. A open-quotes quasi-cylindricalclose quotes amplification of the Squire-Long equation is compared with the more complete model and shown to be able to account for most of its behaviour. An advantage of this latter representation is the relatively undetailed description of the flow geometry it requires in order to calculate a solution. open-quotes Criticalityclose quotes or the ability of small disturbances to propagate upstream is related to results of the quasi-cylindrical and axisymmetric flow models. This leads to an examination of claims made by researchers such as Benjamin and Hall concerning the interrelationship between open-quotes failureclose quotes of the quasi-cylindrical model and the occurrence of a open-quotes criticalclose quotes flow state. Lundgren developed an analytical model for homogeneous turbulence based on a collection of contracting spiral vortices each embedded in an axisymmetric strain field. Using asymptotic approximations he was able to deduce the Kolmogorov k -5/3 behaviour for inertial scales in the turbulence energy spectrum. Pullin ampersand Saffman have enlarged upon his work to make a number of predictions about the behaviour of turbulence described by the model. This work investigates the model numerically. The first part considers how the flow description compares with numerical simulations using the Navier-Stokes equations

  1. Nutrição em Unidade de Cuidados Intensivos -Parte II

    Directory of Open Access Journals (Sweden)

    Cecília Mendonça

    1996-07-01

    Full Text Available RESUMO: Nesta parte II do artigo “Nutrição em Unidade de Cuidados Intensivos” os autores privilegiam a via entérica para administração de nutrientes a doentes com um aparelho gastrointestinal funcionante. Refere-se quando e como iniciar a administração entérica e as contraindicações associadas à sua utilização, as sondas utilizadas e as técnicas de colocação. Quando a administração entérica está indicada por períodos prolongados pode ser importante discutir as vaotagens da efectivação de gastrostomia ou enterostomia.A colocação indevida das sondas na árvore traqueo-brônquica, a aspiração e a diarreia são as principais complicações da administração entérica.A administração entérica pode ser realizada de forma intermitente ou contínua. O resíduo gástrico deve ser avaliado regularmente e, se houver necessidade, pode recorrer-se à utilização de procinéticos.São discutidas fórmulas especiais de administração entérica dirigidas nomeadamente aos doentes com DPOC, Insuficiência Renal e Diabetes. É focada a problemática da realimentação e sobrealimentação.Finalmente são tratadas as indicações e controlo da alimentação parentérica. SUMMARY: In the second part of “Nutrition in Intensive Care Unit” the authors emphasise the importance of enteric route for the administration of nutrients to patients with a normal condition of the gastroinstestinal tract. The rules for when and how initiate the enteric feeding and the associate contra indications, as well as the utilised catheters and techniques of implementation, are expressed in this article. When the enteric feeding is indicated for a long period of time, the advantages of gastrostomy or enterostomy, should be considered.The incorrect positioning of the feeding catheter in tracheobronchial tree

  2. Characterization of sugar cane bagasse: part II: fluid dynamic characteristics; Caracterizacion del bagazo de la cana de azucar: parte II: caracteristicas fluidodinamicas

    Energy Technology Data Exchange (ETDEWEB)

    Alarcon, Guillermo A. Roca [Universidad de Oriente (CEEFE/UO), Santiago de Cuba (Cuba). Centro de Estudios de Eficiencia Energetica], Emails: roca@ceefe.uo.edu.cu, grocabayamon@hotmail.com; Sanchez, Caio Glauco [Universidade Estadual de Campinas (FEM/UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica], Email: caio@fem.unicamp.br; Gomez, Edgardo Olivares [Universidade Estadual de Campinas (NIPE/UNICAMP), SP (Brazil). Nucleo Interdisciplinar de Planejamento Energetico], Emails: gomez@bioware.com.br, egomez@energiabr.org.br; Cortez, Luis Augusto Barbosa [Universidade Estadual de Campinas (NIPE/FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola. Nucleo Interdisciplinar de Planejamento Energetico], Email: cortez@reitoria.unicamp.br

    2006-07-01

    This paper is the second part of a general study about physic-geometrical and fluid-dynamics characteristic of the sugarcane bagasse particles. These properties has relevant importance on the dimensions and operation of the equipment for transport and treatment of solid particles. Was used the transport column method for the determination of the drag velocity and later on the drag coefficient of the sugarcane bagasse particles was calculated. Both, the installation and experimental technique used for materials of these characteristics are simple and innovations tools, but rigorous conceptually, thus the results obtained are reliable. Were used several sugarcane bagasse fractions of particles of known mean diameter. The properties determined were expressed as a function of Reynolds and Archimedes a dimensional criteria. The best considered model from statistical analysis (model from equation 8) was statistically validated for determined ranges of Reynolds and Archimedes. These empirical equations can be used to determine these properties in the range and conditions specified and also for modeling some processes where these fractions are employed. (author)

  3. Magnetically leviated superconducting bearing

    Science.gov (United States)

    Weinberger, Bernard R.; Lynds, Jr., Lahmer

    1993-01-01

    A magnetically levitated superconducting bearing includes a magnet (2) mounted on a shaft (12) that is rotatable around an axis of rotation and a Type II superconductor (6) supported on a stator (14) in proximity to the magnet (2). The superconductor (6) is positioned so that when it is cooled to its superconducting state in the presence of a magnetic field, it interacts with the magnet (2) to produce an attractive force that levitates the magnet (2) and supports a load on the shaft (12). The interaction between the superconductor (6) and magnet(2) also produces surface screening currents (8) that generate a repulsive force perpendicular to the load. The bearing also has means for maintaining the superconductor at a temperature below its critical temperature (16, 18). The bearing could also be constructed so the magnet (2) is supported on the stator (14) and the superconductor (6) is mounted on the shaft (12). The bearing can be operated by cooling the superconductor (6) to its superconducting state in the presence of a magnetic field.

  4. Technical Information on the Carbonation of the EBR-II Reactor, Summary Report Part 1: Laboratory Experiments and Application to EBR-II Secondary Sodium System

    Energy Technology Data Exchange (ETDEWEB)

    Steven R. Sherman

    2005-04-01

    Residual sodium is defined as sodium metal that remains behind in pipes, vessels, and tanks after the bulk sodium metal has been melted and drained from such components. The residual sodium has the same chemical properties as bulk sodium, and differs from bulk sodium only in the thickness of the sodium deposit. Typically, sodium is considered residual when the thickness of the deposit is less than 5-6 cm. This residual sodium must be removed or deactivated when a pipe, vessel, system, or entire reactor is permanently taken out of service, in order to make the component or system safer and/or to comply with decommissioning regulations. As an alternative to the established residual sodium deactivation techniques (steam-and-nitrogen, wet vapor nitrogen, etc.), a technique involving the use of moisture and carbon dioxide has been developed. With this technique, sodium metal is converted into sodium bicarbonate by reacting it with humid carbon dioxide. Hydrogen is emitted as a by-product. This technique was first developed in the laboratory by exposing sodium samples to humidified carbon dioxide under controlled conditions, and then demonstrated on a larger scale by treating residual sodium within the Experimental Breeder Reactor II (EBR-II) secondary cooling system, followed by the primary cooling system, respectively. The EBR-II facility is located at the Idaho National Laboratory (INL) in southeastern Idaho, U.S.A. This report is Part 1 of a two-part report. It is divided into three sections. The first section describes the chemistry of carbon dioxide-water-sodium reactions. The second section covers the laboratory experiments that were conducted in order to develop the residual sodium deactivation process. The third section discusses the application of the deactivation process to the treatment of residual sodium within the EBR-II secondary sodium cooling system. Part 2 of the report, under separate cover, describes the application of the technique to residual sodium

  5. Overlooked Talent Sources and Corporate Strategies for Affirmative Action. Part II

    Science.gov (United States)

    Iacobelli, John L.; Muczyk, Jan P.

    1975-01-01

    Part Two of the two-part article describes corporate strategies for affirmative action in order to obtain the most qualified individuals available for professional positions among minority and female candidates. (Author/BP)

  6. Journal Bearings

    Directory of Open Access Journals (Sweden)

    Renato Brancati

    1999-01-01

    determined after acquiring and analysing the orbits described by the journal axis for assigned unbalance values in different operating conditions. Analysis of the results shows some particular operating features that were not entirely predicted by the theoretical model and which may give rise to malfunctions in the rotor-tilting pad bearings system. The tests were carried out in the rotor dynamics laboratory of the Dipartimento di Ingegneria Meccanica per l'Energetica at the University of Naples.

  7. Camshaft bearing arrangement

    Energy Technology Data Exchange (ETDEWEB)

    Aoi, K.; Ozawa, T.

    1986-06-10

    A bearing arrangement is described for the camshaft of an internal combustion engine or the like which camshaft is formed along its length in axial order with a first bearing surface, a first cam lobe, a second bearing surface, a second cam lobe, a third bearing surface, a third cam lobe and a fourth bearing surface, the improvement comprising first bearing means extending around substantially the full circumference of the first bearing surface and journaling the first bearing surface, second bearing means extending around substantially less than the circumference of the second bearing surface and journaling the second bearing surface, third bearing means extending around substantially less than the circumference of the third bearing surface and journaling the third bearing surface, and fourth bearing means extending around substantially the full circumference of the fourth bearing surface and journaling the first bearing surface.

  8. Evaluación neurofuncional del tallo cerebral Parte II: Reflejo mandibular = Neurofunctional evaluation of brain stem. II. Mandibular reflex

    Directory of Open Access Journals (Sweden)

    Leon Sarmiento, Fidias E.

    2011-09-01

    Full Text Available El reflejo mandibular o maseterino posee conexiones nerviosas únicas, diferentes de las exhi­bidas por otros reflejos monosinápticos humanos, y permite evaluar, de forma fácil y eficien­te, el tallo cerebral por medio de la estimulación mecánica, eléctrica o magnética. Diversos estudios han demostrado la participación en este reflejo de las interneuronas del tallo cerebral y su modulación por estructuras supraespinales, que hacen parte fundamental de su integra­ción motora. El reflejo mandibular es útil para evaluar la afectación trigémino-trigeminal en polineuropatías como la diabetes, neuromiopatías como la esclerosis múltiple y en pacientes con trastornos del movimiento, con o sin disfunción oromandibular. La evaluación neuro­funcional de este reflejo craneofacial ayuda a identificar la integración sensorimotora del tallo cerebral y las posibles alteraciones de estas vías reflejas, debidas a anormalidades del sistema nervioso central o del periférico. Su apropiada ejecución e interpretación, clínica y neurológica, permite aplicar de manera más personalizada diversos protocolos de neurorre­habilitación, con el fin de ayudar a mejorar la calidad de vida de los individuos con afectación de estas vías neurales.

  9. Current antiviral drugs and their analysis in biological materials - Part II: Antivirals against hepatitis and HIV viruses.

    Science.gov (United States)

    Nováková, Lucie; Pavlík, Jakub; Chrenková, Lucia; Martinec, Ondřej; Červený, Lukáš

    2018-01-05

    This review is a Part II of the series aiming to provide comprehensive overview of currently used antiviral drugs and to show modern approaches to their analysis. While in the Part I antivirals against herpes viruses and antivirals against respiratory viruses were addressed, this part concerns antivirals against hepatitis viruses (B and C) and human immunodeficiency virus (HIV). Many novel antivirals against hepatitis C virus (HCV) and HIV have been introduced into the clinical practice over the last decade. The recent broadening portfolio of these groups of antivirals is reflected in increasing number of developed analytical methods required to meet the needs of clinical terrain. Part II summarizes the mechanisms of action of antivirals against hepatitis B virus (HBV), HCV, and HIV, their use in clinical practice, and analytical methods for individual classes. It also provides expert opinion on state of art in the field of bioanalysis of these drugs. Analytical methods reflect novelty of these chemical structures and use by far the most current approaches, such as simple and high-throughput sample preparation and fast separation, often by means of UHPLC-MS/MS. Proper method validation based on requirements of bioanalytical guidelines is an inherent part of the developed methods. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. 14 CFR 23.623 - Bearing factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Bearing factors. 23.623 Section 23.623... Bearing factors. (a) Each part that has clearance (free fit), and that is subject to pounding or vibration, must have a bearing factor large enough to provide for the effects of normal relative motion. (b) For...

  11. DOE program guide for universities and other research groups. Part I. DOE Research and Development Programs; Part II. DOE Procurement and Assistance Policies/Procedures

    Energy Technology Data Exchange (ETDEWEB)

    1980-03-01

    This guide addresses the DOE responsibility for fostering advanced research and development of all energy resources, both current and potential. It is intended to provide, in a single publication, all the fundamental information needed by an institution to develop a potential working relationship with DOE. Part I describes DOE research and development programs and facilities, and identifies areas of additional research needs and potential areas for new research opportunities. It also summarizes budget data and identifies the DOE program information contacts for each program. Part II provides researchers and research administrators with an introduction to the DOE administrative policies and procedures for submission and evaluation of proposals and the administration of resulting grants, cooperative agreements, and research contracts. (RWR)

  12. Programming an interim report on the SETL project. Part I: generalities. Part II: the SETL language and examples of its use

    Energy Technology Data Exchange (ETDEWEB)

    Schwartz, J T

    1975-06-01

    A summary of work during the past several years on SETL, a new programming language drawing its dictions and basic concepts from the mathematical theory of sets, is presented. The work was started with the idea that a programming language modeled after an appropriate version of the formal language of mathematics might allow a programming style with some of the succinctness of mathematics, and that this might ultimately enable one to express and experiment with more complex algorithms than are now within reach. Part I discusses the general approach followed in the work. Part II focuses directly on the details of the SETL language as it is now defined. It describes the facilities of SETL, includes short libraries of miscellaneous and of code optimization algorithms illustrating the use of SETL, and gives a detailed description of the manner in which the set-theoretic primitives provided by SETL are currently implemented. (RWR)

  13. A critical overview of non-aqueous capillary electrophoresis. Part II: separation efficiency and analysis time.

    Science.gov (United States)

    Kenndler, Ernst

    2014-03-28

    A survey of the literature on non-aqueous capillary zone electrophoresis leaves one with the impression of a prevailing notion that non-aqueous conditions are principally more favorable than conventional aqueous media. Specifically, the application of organic solvents in capillary zone electrophoresis (CZE) is believed to provide the general advantages of superior separation efficiency, higher applicable electric field strength, and shorter analysis time. These advantages, however, are often claimed without providing any experimental evidence, or based on rather uncritical comparisons of limited sets of arbitrarily selected separation results. Therefore, the performance characteristics of non-aqueous vs. aqueous CZE certainly deserve closer scrutiny. The primary intention of Part II of this review is to give a critical survey of the literature on non-aqueous capillary electrophoresis (NACE) that has emerged over the last five years. Emphasis is mainly placed on those studies that are concerned with the aspects of plate height, plate number, and the crucial mechanisms contributing to zone broadening, both in organic and aqueous conditions. To facilitate a deeper understanding, this treatment covers also the theoretical fundamentals of peak dispersion phenomena arising from wall adsorption; concentration overload (electromigration dispersion); longitudinal diffusion; and thermal gradients. Theoretically achievable plate numbers are discussed, both under limiting (at zero ionic strength) and application-relevant conditions (at finite ionic strength). In addition, the impact of the superimposed electroosmotic flow contributions to overall CZE performance is addressed, both for aqueous and non-aqueous media. It was concluded that for peak dispersion due to wall adsorption and due to concentration overload (electromigration dispersion, leading to peak triangulation) no general conjunction with the solvent can be deduced. This is in contrast to longitudinal diffusion: the

  14. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XV, UNDERSTANDING DC GENERATOR PRINCIPLES (PART II).

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF MAINTENANCE PROCEDURES FOR DIRECT CURRENT GENERATORS USED ON DIESEL POWERED EQUIPMENT. TOPICS ARE SPECIAL GENERATOR CIRCUITS, GENERATOR TESTING, AND GENERATOR POLARITY. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL PROGRAMED TRAINING FILM "DC GENERATORS II--GENERATOR…

  15. Studies on the sediments of Vembanad Lake, Kerala state: Part II - Distribution of phosphorus

    Digital Repository Service at National Institute of Oceanography (India)

    Murty, P.S.N.; Veerayya, M.

    in the estuarine region has been attributed to several factors. The impoverishment of Mn and Co can be due to (i) desorption of these elements from the river borne detritus on coming into contact with saline waters, (ii) dredging operations which may lead...

  16. 49 CFR Appendix II to Part 805 - Employees Required To Submit Statements

    Science.gov (United States)

    2010-10-01

    ...—Employees Required To Submit Statements Statements of employment and financial interests are required of the... 49 Transportation 7 2010-10-01 2010-10-01 false Employees Required To Submit Statements II...) Office of the managing director: (1) Legislative affairs officer. (2) Program analysis officer. (d...

  17. Research In Diagnosing Bearing Defects From Vibrations

    Science.gov (United States)

    Zoladz, T.; Earhart, E.; Fiorucci, T.

    1995-01-01

    Report describes research in bearing-defect signature analysis - use of vibration-signal analysis to diagnose defects in roller and ball bearings. Experiments performed on bearings in good condition and other bearings in which various parts scratched to provide known defects correlated with vibration signals. Experiments performed on highly instrumented motor-driven rotor assembly at speeds up to 10,050 r/min, using accelerometers, velocity probes, and proximity sensors mounted at various locations on assembly to measure vibrations.

  18. Rise, fall and resurrection of chromosome territories: a historical perspective Part II. Fall and resurrection of chromosome territories during the 1950s to 1980s. Part III. Chromosome territories and the functional nuclear architecture: experiments and m

    OpenAIRE

    T Cremer; C Cremer

    2009-01-01

    Part II of this historical review on the progress of nuclear architecture studies points out why the original hypothesis of chromosome territories from Carl Rabl and Theodor Boveri (described in part I) was abandoned during the 1950s and finally proven by compelling evidence forwarded by laser-uvmicrobeam studies and in situ hybridization experiments. Part II also includes a section on the development of advanced light microscopic techniques breaking the classical Abbe limit written for reade...

  19. Not-for-profit versus for-profit health care providers--Part II: Comparing and contrasting their records.

    Science.gov (United States)

    Rotarius, Timothy; Trujillo, Antonio J; Liberman, Aaron; Ramirez, Bernardo

    2006-01-01

    The debate over which health care providers are most capably meeting their responsibilities in serving the public's interest continues unabated, and the comparisons of not-for-profit (NFP) versus for-profit (FP) hospitals remain at the epicenter of the discussion. From the perspective of available factual information, which of the two sides to this debate is correct? This article is part II of a 2-part series on comparing and contrasting the performance records of NFP health care providers with their FP counterparts. Although it is demonstrated that both NFP and FP providers perform virtuous and selfless feats on behalf of America's public, it is also shown that both camps have been accused of being involved in potentially willful clinical and administrative missteps. Part I provided the background information (eg, legal differences, perspectives on social responsibility, and types of questionable and fraudulent behavior) required to adequately understand the scope of the comparison issue. Part II offers actual comparisons of the 2 organizational structures using several disparate factors such as specific organizational behaviors, approach to the health care priorities of cost and quality, and business-focused goals of profits, efficiency, and community benefit.

  20. Allelic diversity of the MHC class II DRB genes in brown bears (Ursus arctos) and a comparison of DRB sequences within the family Ursidae.

    Science.gov (United States)

    Goda, N; Mano, T; Kosintsev, P; Vorobiev, A; Masuda, R

    2010-11-01

    The allelic diversity of the DRB locus in major histocompatibility complex (MHC) genes was analyzed in the brown bear (Ursus arctos) from the Hokkaido Island of Japan, Siberia, and Kodiak of Alaska. Nineteen alleles of the DRB exon 2 were identified from a total of 38 individuals of U. arctos and were highly polymorphic. Comparisons of non-synonymous and synonymous substitutions in the antigen-binding sites of deduced amino acid sequences indicated evidence for balancing selection on the bear DRB locus. The phylogenetic analysis of the DRB alleles among three genera (Ursus, Tremarctos, and Ailuropoda) in the family Ursidae revealed that DRB allelic lineages were not separated according to species. This strongly shows trans-species persistence of DRB alleles within the Ursidae. © 2010 John Wiley & Sons A/S.

  1. Instrumentation: Photodiode Array Detectors in UV-VIS Spectroscopy. Part II.

    Science.gov (United States)

    Jones, Dianna G.

    1985-01-01

    A previous part (Analytical Chemistry; v57 n9 p1057A) discussed the theoretical aspects of diode ultraviolet-visual (UV-VIS) spectroscopy. This part describes the applications of diode arrays in analytical chemistry, also considering spectroelectrochemistry, high performance liquid chromatography (HPLC), HPLC data processing, stopped flow, and…

  2. Empirical Psycho-Aesthetics and Her Sisters: Substantive and Methodological Issues--Part II

    Science.gov (United States)

    Konecni, Vladimir J.

    2013-01-01

    Empirical psycho-aesthetics is approached in this two-part article from two directions. Part I, which appeared in the Winter 2012 issue of "JAE," addressed definitional and organizational issues, including the field's origins, its relation to "sister" disciplines (experimental philosophy, cognitive neuroscience of art, and neuroaesthetics), and…

  3. As sure as tax, rain or death (Part II) : digitalisation dragons?

    NARCIS (Netherlands)

    Staal, Anne

    2017-01-01

    Tax evasion, delayed trains & untidy death seem to be parts of our daily lives. But what about the digitalisation dragons? Will they wipe away B2B sales and procurement as we know it, our will we see a more nuanced picture? The first Part on this topic so far has attracted 3700+ readers at our PSF

  4. A study of flame spread in engineered cardboard fuelbeds: Part II: Scaling law approach

    Science.gov (United States)

    Brittany A. Adam; Nelson K. Akafuah; Mark Finney; Jason Forthofer; Kozo Saito

    2013-01-01

    In this second part of a two part exploration of dynamic behavior observed in wildland fires, time scales differentiating convective and radiative heat transfer is further explored. Scaling laws for the two different types of heat transfer considered: Radiation-driven fire spread, and convection-driven fire spread, which can both occur during wildland fires. A new...

  5. Green's function of an infinite slot printed between two homogeneous dielectrics - Part II: Uniform asymptotic solution

    NARCIS (Netherlands)

    Maci, S.; Neto, A.

    2004-01-01

    This second part of a two-paper sequence deals with the uniform asymptotic description of the Green's function of an infinite slot printed between two different homogeneous dielectric media. Starting from the magnetic current derived in Part I, the dyadic green's function is first formulated in

  6. Military Curricula for Vocational & Technical Education. Club Restaurant Operations, Part II, 9-10.

    Science.gov (United States)

    Army Quartermaster School, Ft. Lee, VA.

    These programmed instructional materials for part 2 of a secondary-postsecondary subcourse in club management operations are one of a number of military-developed curriculum packages selected for adaptation to vocational instruction and curriculum development in civilian settings. This part of the subcourse consists of three lessons and an…

  7. 10 CFR Appendix II to Part 960 - NRC and EPA Requirements for Preclosure Repository Performance

    Science.gov (United States)

    2010-01-01

    ...) that, except for variances permitted for unusual operations under Section 191.04 as an upper limit..., and schedule. 10 CFR part 20 establishes (a) exposure limits for operating personnel and (b... necessary to ensure consistency with 10 CFR part 60. ...

  8. Edaiila area of interest non-renewable resource assessment (phase 1) Great Bear Lake area, Northwest Territories Parts of NTS 86 K, 86 L, 86 M, 86 N and 96 I

    Energy Technology Data Exchange (ETDEWEB)

    Gebert, J.S.; Jackson, J.E.; O' Neil, C.E. [AMEC Americas Ltd., Calgary, AB (Canada). Earth and Environment Division

    2007-07-01

    The Edaiila study area of interest is located in the Deline District of the Sahtu Settlement area in the Northwest Territories. It lies in the Proterozoic Bear geologic province of the Canadian Shield. The area is currently covered by prospecting claims and is likely undergoing exploration for uranium, precious metals, base metals and diamonds. This document presented a Phase 1 non-renewable resource assessment (NRA) of the area that was completed as part of the Northwest Territories Protect Area Strategy (PAS). It presented compiled historical information, provided a preliminary resource assessment and made recommendations for further Phase 2 studies. This region is within the continuous permafrost zone and is characterized by a high subarctic climate. The study area straddles the tree line and contains vegetation typical of taiga and tundra regions. The bedrock covering the flat to gently rolling topography is covered by undulating glacial drift, raised beaches and outwash deposits. About 25 per cent of the area is covered by wetlands. The Bear province is subdivided into two major domains, the Wopmay orogen and the Coppermine homocline. In the eastern portion of the study area, basement rocks are part of the Great Bear magmatic zone and are locally exposed in the Fault River area. Although basement rocks in the western portion of the study area are not exposed, they are assumed to be composed of the Hottah terrane. 86 refs., 14 tabs., 7 figs., 4 appendices.

  9. Fiducial marker-based correction for involuntary motion in weight-bearing C-arm CT scanning of knees. Part I. Numerical model-based optimization.

    Science.gov (United States)

    Choi, Jang-Hwan; Fahrig, Rebecca; Keil, Andreas; Besier, Thor F; Pal, Saikat; McWalter, Emily J; Beaupré, Gary S; Maier, Andreas

    2013-09-01

    Human subjects in standing positions are apt to show much more involuntary motion than in supine positions. The authors aimed to simulate a complicated realistic lower body movement using the four-dimensional (4D) digital extended cardiac-torso (XCAT) phantom. The authors also investigated fiducial marker-based motion compensation methods in two-dimensional (2D) and three-dimensional (3D) space. The level of involuntary movement-induced artifacts and image quality improvement were investigated after applying each method. An optical tracking system with eight cameras and seven retroreflective markers enabled us to track involuntary motion of the lower body of nine healthy subjects holding a squat position at 60° of flexion. The XCAT-based knee model was developed using the 4D XCAT phantom and the optical tracking data acquired at 120 Hz. The authors divided the lower body in the XCAT into six parts and applied unique affine transforms to each so that the motion (6 degrees of freedom) could be synchronized with the optical markers' location at each time frame. The control points of the XCAT were tessellated into triangles and 248 projection images were created based on intersections of each ray and monochromatic absorption. The tracking data sets with the largest motion (Subject 2) and the smallest motion (Subject 5) among the nine data sets were used to animate the XCAT knee model. The authors defined eight skin control points well distributed around the knees as pseudo-fiducial markers which functioned as a reference in motion correction. Motion compensation was done in the following ways: (1) simple projection shifting in 2D, (2) deformable projection warping in 2D, and (3) rigid body warping in 3D. Graphics hardware accelerated filtered backprojection was implemented and combined with the three correction methods in order to speed up the simulation process. Correction fidelity was evaluated as a function of number of markers used (4-12) and marker distribution

  10. Neutronics and thermohydraulics of the reactor C.E.N.E. Part II

    International Nuclear Information System (INIS)

    Caro, R.

    1976-01-01

    In this report the analysis of neutronics thermohydraulics and shielding of the 10 HWt swimming pool reactor C.E.N.E is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs

  11. Effect of Piers Shape on the Dynamic Structural Responses of Prestressed Concrete Bridge: Part II

    Directory of Open Access Journals (Sweden)

    Ali Fadhil Naser

    2016-03-01

    Full Text Available Pier of bridge is usually used as a general term for any type of substructure located between horizontal spans and foundations. Piers give vertical supports for spans at intermediate points and perform two main functions. The objective of this study is to inspect the effect of piers shape on the dynamic structural performance by adopting theoretical dynamic analysis. The results of dynamic analysis of 25 bridges models show that the maximum value of natural frequency is equal to 5.64Hz in two circles piers bridge model. Therefore, this type of model has good stiffness and bearing capacity. The two square piers model, the one circle pier model, and the two circles piers model appear good stiffness because of the natural frequencies (5.30Hz, 5.52Hz, and 5.64Hz are more than the maximum forced frequencies (4.52Hz, 5.45Hz, and 4.52Hz respectively. According to the comparison between all models results, the two circles piers model has the higher stiffness because of this model has the maximum value of natural frequency (5.64Hz and it is more than all forced vibration frequencies of all others models. Therefore, this study recommends that using the bridge model of two circles piers in the bridges construction that consists of three spans (30m+40m+30m with section of box girder.

  12. Effect of Piers Shape on the Dynamic Structural Responses of Prestressed Concrete Bridge: Part II

    Directory of Open Access Journals (Sweden)

    Ali Fadhil Naser

    2016-12-01

    Full Text Available Pier of bridge is usually used as a general term for any type of substructure located between horizontal spans and foundations. Piers give vertical supports for spans at intermediate points and perform two main functions. The objective of this study is to inspect the effect of piers shape on the dynamic structural performance by adopting theoretical dynamic analysis. The results of dynamic analysis of 25 bridges models show that the maximum value of natural frequency is equal to 5.64Hz in two circles piers bridge model. Therefore, this type of model has good stiffness and bearing capacity. The two square piers model, the one circle pier model, and the two circles piers model appear good stiffness because of the natural frequencies (5.30Hz, 5.52Hz, and 5.64Hz are more than the maximum forced frequencies (4.52Hz, 5.45Hz, and 4.52Hz respectively. According to the comparison between all models results, the two circles piers model has the higher stiffness because of this model has the maximum value of natural frequency (5.64Hz and it is more than all forced vibration frequencies of all others models. Therefore, this study recommends that using the bridge model of two circles piers in the bridges construction that consists of three spans (30m+40m+30m with section of box girder.

  13. Executive Summary: Parts on Demand Project (CATT Phase II) - Volume 1 of 2

    National Research Council Canada - National Science Library

    Gates, Robert

    1996-01-01

    .... The GAO has profiled DoD challenges in: maintaining an aging aircraft fleet, reducing response time and cost of providing the spare parts, implementing commercial inventory management practices, reinventing buying and contracting practices...

  14. 48 CFR 14.201-3 - Part II-Contract clauses.

    Science.gov (United States)

    2010-10-01

    ... CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.201-3 Part II—Contract clauses... law or by this regulation and any additional clauses expected to apply to any resulting contract, if...

  15. Strategic planning for hotel operations: The Ritz-Carlton Hotel Company (Part II).

    Science.gov (United States)

    Shriver, S J

    1993-01-01

    The Ritz-Carlton Hotel Company won the Malcolm Baldrige National Quality Award in 1992. One key to its success is its strategic planning process. In this second part of a two-part article, Stephen Shriver concludes his review of the Ritz-Carlton's approach to strategic planning. Shriver begins by outlining some key steps in plan development and goes on to describe how the Ritz-Carlton disseminates, implements, and evaluates the plan.

  16. The motion planning problem and exponential stabilization of a heavy chain. Part II

    OpenAIRE

    Piotr Grabowski

    2008-01-01

    This is the second part of paper [P. Grabowski, The motion planning problem and exponential stabilization of a heavy chain. Part I, to appear in International Journal of Control], where a model of a heavy chain system with a punctual load (tip mass) in the form of a system of partial differential equations was interpreted as an abstract semigroup system and then analysed on a Hilbert state space. In particular, in [P. Grabowski, The motion planning problem and exponential stabilization of a h...

  17. Global optimization of truss topology with discrete bar areas-Part II: Implementation and numerical results

    DEFF Research Database (Denmark)

    Achtziger, Wolfgang; Stolpe, Mathias

    2009-01-01

    we use the theory developed in Part I to design a convergent nonlinear branch-and-bound method tailored to solve large-scale instances of the original discrete problem. The problem formulation and the needed theoretical results from Part I are repeated such that this paper is self-contained. We focus...... the largest discrete topology design problems solved by means of global optimization....

  18. Non-contacting "snubber bearing" for passive magnetic bearing systems

    Science.gov (United States)

    Post, Richard F

    2017-08-22

    A new non-contacting magnetic "snubber" bearing is provided for application to rotating systems such as vehicular electromechanical battery systems subject to frequent accelerations. The design is such that in the equilibrium position the drag force of the snubber is very small (milliwatts). However in a typical case, if the rotor is displaced by as little as 2 millimeters a large restoring force is generated without any physical contact between the stationary and rotating parts of the snubber bearing.

  19. Field Surveys, IOC Valleys. Biological Resources Survey, Dry Lake Valley, Nevada. Volume II, Part I.

    Science.gov (United States)

    1981-08-01

    years ago; the transplant was considered unsuccessful. Sagebrush is the principal item in the diet of adult sage grouse (Centrocercus urophasianus), and...canyon areas in the normal chukar partridge range but can also extend its range to areas too dry for the chukar. The transplant was not con- sidered...determined. - Ertee E-TR-48-II-I SSL1’N SL xx- C - - _ 0S91’ - - I. 009t N - - 0’J o,, s). N, - . ,o 09 -SW,- - - ,o T z X -4 oseo 0L91 - N - = - ozot ma

  20. Project Monitor: Part II. Conservation in small business: an exploratory study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hammond, P Y

    1979-08-01

    Project Monitor examined the energy conservation attitude and behavior of small samples of small business owners/operators in Allegheny County, Pennsylvania, focusing on manufacturing concerns and retailers. Section I reports the findings on the energy conserving behavior of 92 smaller manufacturers and Section II identifies the factors which affect decision making concerning energy consuming activities by the owners/operators of 94 small retail establishments. In each, the impact of Project Pacesetter and of the coal strike and the general energy situation is considered. (MCW)

  1. Arbitrary order 2D virtual elements for polygonal meshes: part II, inelastic problem

    Science.gov (United States)

    Artioli, E.; Beirão da Veiga, L.; Lovadina, C.; Sacco, E.

    2017-10-01

    The present paper is the second part of a twofold work, whose first part is reported in Artioli et al. (Comput Mech, 2017. doi: 10.1007/s00466-017-1404-5), concerning a newly developed Virtual element method (VEM) for 2D continuum problems. The first part of the work proposed a study for linear elastic problem. The aim of this part is to explore the features of the VEM formulation when material nonlinearity is considered, showing that the accuracy and easiness of implementation discovered in the analysis inherent to the first part of the work are still retained. Three different nonlinear constitutive laws are considered in the VEM formulation. In particular, the generalized viscoelastic model, the classical Mises plasticity with isotropic/kinematic hardening and a shape memory alloy constitutive law are implemented. The versatility with respect to all the considered nonlinear material constitutive laws is demonstrated through several numerical examples, also remarking that the proposed 2D VEM formulation can be straightforwardly implemented as in a standard nonlinear structural finite element method framework.

  2. Anesthesia and ventilation strategies in children with asthma: part II - intraoperative management.

    Science.gov (United States)

    Regli, Adrian; von Ungern-Sternberg, Britta S

    2014-06-01

    As asthma is a frequent disease especially in children, anesthetists are increasingly providing anesthesia for children requiring elective surgery with well controlled asthma but also for those requiring urgent surgery with poorly controlled or undiagnosed asthma. This second part of this two-part review details the medical and ventilatory management throughout the perioperative period in general but also includes the perioperative management of acute bronchospasm and asthma exacerbations in children with asthma. Multiple observational trials assessing perioperative respiratory adverse events in healthy and asthmatic children provide the basis for identifying risk reduction strategies. Mainly, animal experiments and to a small extent clinical data have advanced our understanding of how anesthetic agents effect bronchial smooth muscle tone and blunt reflex bronchoconstriction. Asthma treatment outside anesthesia is well founded on a large body of evidence.Perioperative prevention strategies have increasingly been studied. However, evidence on the perioperative management, including mechanical ventilation strategies of asthmatic children, is still only fair, and further research is required. To minimize the considerable risk of perioperative respiratory adverse events in asthmatic children, perioperative management should be based on two main pillars: the preoperative optimization of asthma treatment (please refer to the first part of this two-part review) and - the focus of this second part of this review - the optimization of anesthesia management in order to optimize lung function and minimize bronchial hyperreactivity in the perioperative period.

  3. Transactive System: Part II: Analysis of Two Pilot Transactive Systems using Foundational Theory and Metrics

    Energy Technology Data Exchange (ETDEWEB)

    Lian, Jianming [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sun, Y. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kalsi, Karanjit [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Widergren, Steven E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wu, Di [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ren, Huiying [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2018-01-24

    This document is the second of a two-part report. Part 1 reviewed several demonstrations of transactive control and compared them in terms of their payoff functions, control decisions, information privacy, and mathematical solution concepts. It was suggested in Part 1 that these four listed components should be adopted for meaningful comparison and design of future transactive systems. Part 2 proposes qualitative and quantitative metrics that will be needed to compare alternative transactive systems. It then uses the analysis and design principles from Part 1 while conducting more in-depth analysis of two transactive demonstrations: the American Electric Power (AEP) gridSMART Demonstration, which used a double –auction market mechanism, and a consensus method like that used in the Pacific Northwest Smart Grid Demonstration. Ultimately, metrics must be devised and used to meaningfully compare alternative transactive systems. One significant contribution of this report is an observation that the decision function used for thermostat control in the AEP gridSMART Demonstration has superior performance if its decision function is recast to more accurately reflect the power that will be used under for thermostatic control under alternative market outcomes.

  4. Controlled Nonlinear Stochastic Delay Equations: Part II: Approximations and Pipe-Flow Representations

    International Nuclear Information System (INIS)

    Kushner, Harold J.

    2012-01-01

    This is the second part of a work dealing with key issues that have not been addressed in the modeling and numerical optimization of nonlinear stochastic delay systems. We consider new classes of models, such as those with nonlinear functions of several controls (such as products), each with is own delay, controlled random Poisson measure driving terms, admissions control with delayed retrials, and others. Part I was concerned with issues concerning the class of admissible controls and their approximations, since the classical definitions are inadequate for our models. This part is concerned with transportation equation representations and their approximations. Such representations of nonlinear stochastic delay models have been crucial in the development of numerical algorithms with much reduced memory and computational requirements. The representations for the new models are not obvious and are developed. They also provide a template for the adaptation of the Markov chain approximation numerical methods.

  5. A review of breast tomosynthesis. Part II. Image reconstruction, processing and analysis, and advanced applications

    Science.gov (United States)

    Sechopoulos, Ioannis

    2013-01-01

    Many important post-acquisition aspects of breast tomosynthesis imaging can impact its clinical performance. Chief among them is the reconstruction algorithm that generates the representation of the three-dimensional breast volume from the acquired projections. But even after reconstruction, additional processes, such as artifact reduction algorithms, computer aided detection and diagnosis, among others, can also impact the performance of breast tomosynthesis in the clinical realm. In this two part paper, a review of breast tomosynthesis research is performed, with an emphasis on its medical physics aspects. In the companion paper, the first part of this review, the research performed relevant to the image acquisition process is examined. This second part will review the research on the post-acquisition aspects, including reconstruction, image processing, and analysis, as well as the advanced applications being investigated for breast tomosynthesis. PMID:23298127

  6. Evaluation and diagnosis of the hair loss patient: part II. Trichoscopic and laboratory evaluations.

    Science.gov (United States)

    Mubki, Thamer; Rudnicka, Lidia; Olszewska, Malgorzata; Shapiro, Jerry

    2014-09-01

    The use of trichoscopy for evaluating a number of hair and scalp disorders is gaining popularity. It is a simple and noninvasive in vivo tool for visualizing hair shafts and the scalp. Recently, alopecias have been classified according to their trichoscopic findings. The second part of this 2-part continuing medical education article reviews recent advances in this field and describes a systematic approach for using the differential diagnostic findings of trichoscopy in alopecia. Copyright © 2014 American Academy of Dermatology, Inc. Published by Mosby, Inc. All rights reserved.

  7. Light detection and ranging measurements of wake dynamics. Part II: two-dimensional scanning

    DEFF Research Database (Denmark)

    Trujillo, Juan-José; Bingöl, Ferhat; Larsen, Gunner Chr.

    2011-01-01

    the instantaneous transversal wake position which is quantitatively compared with the prediction of the Dynamic Wake Meandering model. The results, shown for two 10-min time series, suggest that the conjecture of the wake behaving as a passive tracer is a fair approximation; this corroborates and expands...... the results of one-dimensional measurements already presented in the first part of this paper. Consequently, it is now possible to separate the deterministic and turbulent parts of the wake wind field, thus enabling capturing the wake in the meandering frame of reference. The results correspond, qualitatively...

  8. FROM ZERO-DIMENSIONAL TO 2-DIMENSIONAL CARBON NANOMATERIALS - part II: GRAPHENE

    Directory of Open Access Journals (Sweden)

    Cătălin IANCU

    2012-05-01

    Full Text Available As was presented in the first part of this review paper, lately, many theoretical and experimental studies have been carried out to develop one of the most interesting aspects of the science and nanotechnology which is called carbon-related nanomaterials. In this review paper are presented some of the most exciting and important developments in the synthesis, properties, and applications of low-dimensional carbon nanomaterials. In this part of the paper are presented the synthesis techniques used to produce the two-dimensional carbon nanomaterials (including graphene, and also the most important properties and potential applications of graphene.

  9. Optimisation of energy absorbing liner for equestrian helmets. Part II: Functionally graded foam liner

    International Nuclear Information System (INIS)

    Cui, L.; Forero Rueda, M.A.; Gilchrist, M.D.

    2009-01-01

    The energy absorbing liner of safety helmets was optimised using finite element modelling. In this present paper, a functionally graded foam (FGF) liner was modelled, while keeping the average liner density the same as in a corresponding reference single uniform density liner model. Use of a functionally graded foam liner would eliminate issues regarding delamination and crack propagation between interfaces of different density layers which could arise in liners with discrete density variations. As in our companion Part I paper [Forero Rueda MA, Cui L, Gilchrist MD. Optimisation of energy absorbing liner for equestrian helmets. Part I: Layered foam liner. Mater Des [submitted for publication

  10. Mammalian Toxicity of Munition Compounds. Phase II. Effects of Multiple Doses. Part III. 2,6-Dinitrotoluene

    Science.gov (United States)

    1976-07-01

    and the neuromuscular effects in these dogs were not due to hypocalcemia . The lowest serum calcium concen- tration in these dogs was 4.2 meq/liter...motor end plate might produce a local hypocalcemia . Such a mechanism is purely speculative. Qualitatively and quantitavely, most of the effects of 2,6...I ýNw,- -MIM I/ MIDWEST RESEARCH INS14ITUTE H0q .3L I LU -_ MAMMALIAN TOXICITY OF MUNITIONS COMPOUlNDSPHASE II: EFFECTS OF MiULTIPLE DOSES C* •PART

  11. The decision to extract: part II. Analysis of clinicians' stated reasons for extraction.

    Science.gov (United States)

    Baumrind, S; Korn, E L; Boyd, R L; Maxwell, R

    1996-04-01

    In a recently reported study, the pretreatment records of each subject in a randomized clinical trial of 148 patients with Class I and Class II malocclusions presenting for orthodontic treatment were evaluated independently by five experienced clinicians (drawn from a panel of 14). The clinicians displayed a higher incidence of agreement with each other than had been expected with respect to the decision as to whether extraction was indicated in each specific case. To improve our understanding of how clinicians made their decisions on whether to extract or not, the records of a subset of 72 subjects randomly selected from the full sample of 148, have now been examined in greater detail. In 21 of these cases, all five clinicians decided to treat without extraction. Among the remaining 51 cases, there were 202 decisions to extract (31 unanimous decision cases and 20 split decision cases). The clinicians cited a total of 469 reasons to support these decisions. Crowding was cited as the first reason in 49% of decisions to extract, followed by incisor protrusion (14%), need for profile correction (8%), Class II severity (5%), and achievement of a stable result (5%). When all the reasons for extraction in each clinician's decision were considered as a group, crowding was cited in 73% of decisions, incisor protrusion in 35%, need for profile correction in 27%, Class II severity in 15% and posttreatment stability in 9%. Tooth size anomalies, midline deviations, reduced growth potential, severity of overjet, maintenance of existing profile, desire to close the bite, periodontal problems, and anticipation of poor cooperation accounted collectively for 12% of the first reasons and were mentioned in 54% of the decisions, implying that these considerations play a consequential, if secondary, role in the decision-making process. All other reasons taken together were mentioned in fewer than 20% of cases. In this sample at least, clinicians focused heavily on appearance

  12. Facilitating age diversity in organizations – part II: managing perceptions and interactions

    NARCIS (Netherlands)

    Hertel, Guido; van der Heijden, Beatrice; de Lange, Annet H.; Deller, Jürgen

    2013-01-01

    Purpose – Due to demographic changes in most industrialized countries, the average age of working people is continuously increasing, and the workforce is becoming more age-diverse. This review, together with the earlier JMP Special Issue “Facilitating age diversity in organizations – part I:

  13. Elastic and Piezoelectric Properties of Boron Nitride Nanotube Composites. Part II; Finite Element Model

    Science.gov (United States)

    Kim, H. Alicia; Hardie, Robert; Yamakov, Vesselin; Park, Cheol

    2015-01-01

    This paper is the second part of a two-part series where the first part presents a molecular dynamics model of a single Boron Nitride Nanotube (BNNT) and this paper scales up to multiple BNNTs in a polymer matrix. This paper presents finite element (FE) models to investigate the effective elastic and piezoelectric properties of (BNNT) nanocomposites. The nanocomposites studied in this paper are thin films of polymer matrix with aligned co-planar BNNTs. The FE modelling approach provides a computationally efficient way to gain an understanding of the material properties. We examine several FE models to identify the most suitable models and investigate the effective properties with respect to the BNNT volume fraction and the number of nanotube walls. The FE models are constructed to represent aligned and randomly distributed BNNTs in a matrix of resin using 2D and 3D hollow and 3D filled cylinders. The homogenisation approach is employed to determine the overall elastic and piezoelectric constants for a range of volume fractions. These models are compared with an analytical model based on Mori-Tanaka formulation suitable for finite length cylindrical inclusions. The model applies to primarily single-wall BNNTs but is also extended to multi-wall BNNTs, for which preliminary results will be presented. Results from the Part 1 of this series can help to establish a constitutive relationship for input into the finite element model to enable the modeling of multiple BNNTs in a polymer matrix.

  14. Facilitating age diversity in organizations ‐ part II: managing perceptions and interactions

    NARCIS (Netherlands)

    Annet de Lange; Jürgen Deller; Beatrice van der Heijden; Guido Hertel

    2013-01-01

    Purpose ‐ Due to demographic changes in most industrialized countries, the average age of working people is continuously increasing, and the workforce is becoming more age-diverse. This review, together with the earlier JMP Special Issue "Facilitating age diversity in organizations ‐ part I:

  15. Composición de la pasta de cemento Pórtland (Parte II)

    NARCIS (Netherlands)

    Brouwers, H.J.H.

    2007-01-01

    Esta es Ia segunda parte del articulo que revisa el trabajo de Powers y Brownyard (1948) quienes fueron los primeros que investigaron sistemáticamente a reaccion del cemento con el agua y Ia composicion de Ia pasta de cemento.

  16. Cross-section crushing behaviour of hat-sections (Part II: Analytical modelling)

    NARCIS (Netherlands)

    Hofmeyer, H.

    2005-01-01

    Hat-sections are often used to experimentally investigate building sheeting subject to a concentrated load and bending. In car doors, hat-sections are used for side-impact protection. Their crushing behaviour can partly be explained by only observing their cross-sectional behaviour [1]. This

  17. The Concept of Time in Rehabilitation and Psychosocial Adaptation to Chronic Illness and Disability: Part II

    Science.gov (United States)

    Livneh, Hanoch

    2013-01-01

    The first part of this article focused on providing the reader with a general overview of the concept of time with special emphasis on understanding time's role in the structure of personality theories and their associated therapeutic approaches, as well as linking the discussion to the understanding of time in the context of psychosocial…

  18. Institutional Advancement: A Marketing Perspective. Part II: A Status Report, 1978-79.

    Science.gov (United States)

    Moriarty, Daniel F.

    This follow-up report examines the status of the recruitment and retention strategies implemented by Triton College in 1978 as part of an effort to utilize the marketing concept in identifying and meeting changing educational needs. The report first provides operational definitions for "institutional advancement,""marketing concept,""promotion,"…

  19. Uni-directional waves over slowly varying bottom, part II: Deformation of travelling waves

    NARCIS (Netherlands)

    Pudjaprasetya, S.R.; Pudjaprasetya, S.R.; van Groesen, Embrecht W.C.

    1996-01-01

    A new Korteweg-de Vries type of equation for uni-directional waves over slowly varying bottom has been derived in Part I. The equation retains the Hamiltonian structure of the underlying complete set of equations for surface waves. For flat bottom it reduces to the standard Korteweg-de Vries

  20. Hip protectors: recommendations for conducting clinical trials--an international consensus statement (part II)

    DEFF Research Database (Denmark)

    Cameron, I D; Robinovitch, S; Birge, S

    2010-01-01

    While hip protectors are effective in some clinical trials, many, including all in community settings, have been unable to demonstrate effectiveness. This is due partly to differences in the design and analysis. The aim of this report is to develop recommendations for subsequent clinical research....

  1. MATLAB-based Applications for Image Processing and Image Quality Assessment – Part II: Experimental Results

    Directory of Open Access Journals (Sweden)

    L. Krasula

    2012-04-01

    Full Text Available The paper provides an overview of some possible usage of the software described in the Part I. It contains the real examples of image quality improvement, distortion simulations, objective and subjective quality assessment and other ways of image processing that can be obtained by the individual applications.

  2. Sintering of Multilayered Porous Structures: Part II – Experiments and Model Applications

    DEFF Research Database (Denmark)

    Ni, De Wei; Olevsky, Eugene; Esposito, Vincenzo

    2013-01-01

    Experimental analyses of shrinkage and distortion kinetics during sintering of bilayered porous and dense gadolinium-doped ceria Ce0.9Gd0.1O1.95d structures are carried out, and compared with the theoretical models developed in Part I of this work. A novel approach is developed for the determinat...

  3. Conceptual design of ICF reactor SENRI, Part II. Advances in design and pellet gain scaling

    International Nuclear Information System (INIS)

    Ido, S.; Mima, K.; Nakai, S.; Tsuji, R.; Yamanaka, C.

    1984-01-01

    This chapter reviews the recent design studies on reactor concepts with magnetically guided lithium flow, SENRI-I, SENRI-IA and SENRI-II. The routes from the present status to power reactors and an advanced fuel pellet concept is also discussed. Topics covered include pellet design, magnetohydrodynamic design of liquid lithium flow; reactor cavity concepts with magnetically guided lithium flow, a thermo-hydraulic analysis, a tritium recovery system; and an advanced fuel pellet concept for an inertial confinement fusion (ICF) reactor without a tritium breeding blanket. An advanced fuel pellet for an ICF reactor without a T breeder was studied in the model calculations, which showed sufficiently high values of pellet gain. Includes a table and 8 diagrams

  4. Use of modulated excitation signals in ultrasound. Part II: Design and performance for medical imaging applications

    DEFF Research Database (Denmark)

    Misaridis, Thanassis; Jensen, Jørgen Arendt

    2005-01-01

    ultrasound presents design methods of linear FM signals and mismatched filters, in order to meet the higher demands on resolution in ultrasound imaging. It is shown that for the small time-bandwidth (TB) products available in ultrasound, the rectangular spectrum approximation is not valid, which reduces....... The method is evaluated first for resolution performance and axial sidelobes through simulations with the program Field II. A coded excitation ultrasound imaging system based on a commercial scanner and a 4 MHz probe driven by coded sequences is presented and used for the clinical evaluation of the coded...... excitation/compression scheme. The clinical images show a significant improvement in penetration depth and contrast, while they preserve both axial and lateral resolution. At the maximum acquisition depth of 15 cm, there is an improvement of more than 10 dB in the signal-to-noise ratio of the images...

  5. Ceramic materials for porcelain veneers: part II. Effect of material, shade, and thickness on translucency.

    Science.gov (United States)

    Barizon, Karine T L; Bergeron, Cathia; Vargas, Marcos A; Qian, Fang; Cobb, Deborah S; Gratton, David G; Geraldeli, Saulo

    2014-10-01

    Information regarding the differences in translucency among new ceramic systems is lacking. The purpose of this study was to compare the relative translucency of the different types of ceramic systems indicated for porcelain veneers and to evaluate the effect of shade and thickness on translucency. Disk specimens 13 mm in diameter and 0.7-mm thick were fabricated for the following 9 materials (n=5): VITA VM9, IPS Empress Esthetic, VITA PM9, Vitablocks Mark II, Kavo Everest G-Blank, IPS Empress CAD, IPS e.max CAD, IPS e.maxPress, and Lava Zirconia. VITA VM9 served as the positive control and Lava as the negative control. The disks were fabricated with the shade that corresponds to A1. For IPS e.maxPress, additional disks were made with different shades (BL2, BL4, A1, B1, O1, O2, V1, V2, V3), thickness (0.3 mm), and translucencies (high translucency, low translucency). Color coordinates (CIE L∗ a∗ b∗) were measured with a tristimulus colorimeter. The translucency parameter was calculated from the color difference of the material on a black versus a white background. One-way ANOVA, the post hoc Tukey honestly significant difference, and the Ryan-Einot-Gabriel-Welsch multiple range tests were used to analyze the data (α=.05). Statistically significant differences in the translucency parameter were found among porcelains (PPM9, Empress Esthetic>Empress CAD>Mark II, Everest, e.max CAD>e.max Press>Lava. Significant differences also were noted when different shades and thickness were compared (Pceramic systems designed for porcelain veneers present varying degrees of translucency. The thickness and shade of lithium disilicate ceramic affect its translucency. Shade affects translucency parameter less than thickness. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  6. Mixed ligand complexes of alkaline earth metals: Part XII. Mg(II, Ca(II, Sr(II and Ba(II complexes with 5-chlorosalicylaldehyde and salicylaldehyde or hydroxyaromatic ketones

    Directory of Open Access Journals (Sweden)

    MITHLESH AGRAWAL

    2002-04-01

    Full Text Available The reactions of alkaline earth metal chlorides with 5-chlorosalicylaldehyde and salicylaldehyde, 2-hydroxyacetophenone or 2-hydroxypropiophenone have been carried out in 1 : 1 : 1 mole ratio and the mixed ligand complexes of the type MLL’(H2O2 (where M = Mg(II, Ca(II, Sr(II and Ba(II, HL = 5-chlorosalicylaldehyde and HL’ = salicylaldehyde, 2-hydroxyacetophenone or 2-hydroxypropiophenone have been isolated. These complexes were characterized by TLC, conductance measurements, IR and 1H-NMR spectra.

  7. Converting Eucalyptus biomass into ethanol: Financial and sensitivity analysis in a co-current dilute acid process. Part II

    International Nuclear Information System (INIS)

    Gonzalez, R.; Treasure, T.; Phillips, R.; Jameel, H.; Saloni, D.; Wright, J.; Abt, R.

    2011-01-01

    The technical and financial performance of high yield Eucalyptus biomass in a co-current dilute acid pretreatment followed by enzymatic hydrolysis process was simulated using WinGEMS registered and Excel registered . Average ethanol yield per dry Mg of Eucalyptus biomass was approximately 347.6 L of ethanol (with average carbohydrate content in the biomass around 66.1%) at a cost of 0.49 L -1 of ethanol, cash cost of ∝0.46 L -1 and CAPEX of 1.03 L -1 of ethanol. The main cost drivers are: biomass, enzyme, tax, fuel (gasoline), depreciation and labor. Profitability of the process is very sensitive to biomass cost, carbohydrate content (%) in biomass and enzyme cost. Biomass delivered cost was simulated and financially evaluated in Part I; here in Part II the conversion of this raw material into cellulosic ethanol using the dilute acid process is evaluated. (author)

  8. Japanese contributions to IAEA INTOR workshop, phase two A, part 2, chapter I: introduction, and chapter II: summary

    International Nuclear Information System (INIS)

    Mori, Sigeru; Tomabechi, Ken; Fujisawa, Noboru; Iida, Hiromasa; Sugihara, Masayoshi; Seki, Masahiro; Honda, Tsutomu; Kasai, Masao; Itoh, Shin-ichi.

    1985-07-01

    This report corresponds to Chapters I and II of Japanese contribution report to IAEA INTOR Workshop, Phase Two A, Part 2. The major objectives of the INTOR workshop, Phase Two A, Part 2 are to study critical technical issues, and to assess scientific and technical data bases, and to finally upgrade the INTOR design concept. To study critical technical issues that affect the feasibility or practicability of the INTOR design concept, the following five groups are organized; (A) Impurity control, (B) RF heating and current drive, (C) Transient electromagnetics, (D) Maintainability, (E) Technical benefit. In addition to those groups, the three disciplinary groups are organized to assess the worldiode scientific and technical data bases that exist now and that will exist 4-5 years to support the detailed design and construction of an INTOR-like machine, and to identify additional R D that is required; (F) Physics, (G) Engineering, (H) Nuclear. (author)

  9. Pedagogical progeniture or tactical translation? George Fordyce's additions and modifications to William Cullen's philosophical chemistry--Part II.

    Science.gov (United States)

    Taylor, Georgette

    2014-08-01

    This paper compares the affinity theories and the associated affinity diagrams of William Cullen (1710-1790) and George Fordyce (1736-1802), exploring in particular one episode that took place during the brief hiatus between Fordyce's student years at Edinburgh University and the start of his own pedagogical career in London. This investigation complements that contained in Part I of this paper, which compared the chemistry courses given by Cullen and Fordyce, demonstrating that the knowledge originally imparted to Fordyce by Cullen in his Edinburgh lectures was augmented and translated by Fordyce for his own pedagogical purposes. Part II offers greater insight into the flow of knowledge between Fordyce and Cullen. Their correspondence suggests that the relationship between master and student transmuted into something more complicated after Fordyce left Edinburgh, while the model of knowledge transmission between the two can be seen to be more collaborative than might be expected.

  10. Passive magnetic bearing system

    Science.gov (United States)

    Post, Richard F.

    2014-09-02

    An axial stabilizer for the rotor of a magnetic bearing provides external control of stiffness through switching in external inductances. External control also allows the stabilizer to become a part of a passive/active magnetic bearing system that requires no external source of power and no position sensor. Stabilizers for displacements transverse to the axis of rotation are provided that require only a single cylindrical Halbach array in its operation, and thus are especially suited for use in high rotation speed applications, such as flywheel energy storage systems. The elimination of the need of an inner cylindrical array solves the difficult mechanical problem of supplying support against centrifugal forces for the magnets of that array. Compensation is provided for the temperature variation of the strength of the magnetic fields of the permanent magnets in the levitating magnet arrays.

  11. Musculoskeletal disorders associated with HIV infection and AIDS. Part II: Non-infectious musculoskeletal conditions

    International Nuclear Information System (INIS)

    Tehranzadeh, Jamshid; Ter-Oganesyan, Ramon R.; Steinbach, Lynne S.

    2004-01-01

    This section of a two-part series on musculoskeletal disorders associated with HIV infection and AIDS reviews the non-infectious musculoskeletal conditions. In the first part, the infectious conditions were reviewed. The non-infectious conditions include polymyositis, drug-induced myopathy, myositis ossificans, adhesive capsulitis, avascular necrosis, bone marrow abnormalities, and hypertrophic osteoarthropathy. Inflammatory and reactive arthropathies are more prevalent in HIV-positive individuals, and a separate section is dedicated to these conditions, including Reiter's syndrome, psoriatic arthritis, HIV-associated arthritis, painful articular syndrome, and acute symmetric polyarthritis. Lastly, we include a discussion of HIV-related neoplastic processes that affect the musculoskeletal system, namely Kaposi's sarcoma and non-Hodgkin's lymphoma. (orig.)

  12. Musculoskeletal disorders associated with HIV infection and AIDS. Part II: Non-infectious musculoskeletal conditions

    Energy Technology Data Exchange (ETDEWEB)

    Tehranzadeh, Jamshid [Department of Radiological Sciences, University of California, Irvine, CA (United States); Department of Radiological Sciences, Orange, CA (United States); Ter-Oganesyan, Ramon R. [College of Medicine, University of California, Irvine, CA (United States); Steinbach, Lynne S. [Department of Radiological Sciences, University of California, San Francisco (United States)

    2004-06-01

    This section of a two-part series on musculoskeletal disorders associated with HIV infection and AIDS reviews the non-infectious musculoskeletal conditions. In the first part, the infectious conditions were reviewed. The non-infectious conditions include polymyositis, drug-induced myopathy, myositis ossificans, adhesive capsulitis, avascular necrosis, bone marrow abnormalities, and hypertrophic osteoarthropathy. Inflammatory and reactive arthropathies are more prevalent in HIV-positive individuals, and a separate section is dedicated to these conditions, including Reiter's syndrome, psoriatic arthritis, HIV-associated arthritis, painful articular syndrome, and acute symmetric polyarthritis. Lastly, we include a discussion of HIV-related neoplastic processes that affect the musculoskeletal system, namely Kaposi's sarcoma and non-Hodgkin's lymphoma. (orig.)

  13. Traveling-wave piezoelectric linear motor part II: experiment and performance evaluation.

    Science.gov (United States)

    Ting, Yung; Li, Chun-Chung; Chen, Liang-Chiang; Yang, Chieh-Min

    2007-04-01

    This article continues the discussion of a traveling-wave piezoelectric linear motor. Part I of this article dealt with the design and analysis of the stator of a traveling-wave piezoelectric linear motor. In this part, the discussion focuses on the structure and modeling of the contact layer and the carriage. In addition, the performance analysis and evaluation of the linear motor also are dealt with in this study. The traveling wave is created by stator, which is constructed by a series of bimorph actuators arranged in a line and connected to form a meander-line structure. Analytical and experimental results of the performance are presented and shown to be almost in agreement. Power losses due to friction and transmission are studied and found to be significant. Compared with other types of linear motors, the motor in this study is capable of supporting heavier loads and provides a larger thrust force.

  14. Nanotechnology and its relationship to interventional radiology. Part II: Drug Delivery, Thermotherapy, and Vascular Intervention.

    LENUS (Irish Health Repository)

    Power, Sarah

    2012-02-01

    Nanotechnology can be defined as the design, creation, and manipulation of structures on the nanometer scale. This two-part review is intended to acquaint the interventionalist with the field of nanotechnology, and provide an overview of potential applications, while highlighting advances relevant to interventional radiology. Part 2 of the article concentrates on drug delivery, thermotherapy, and vascular intervention. In oncology, advances in drug delivery allow for improved efficacy, decreased toxicity, and greater potential for targeted therapy. Magnetic nanoparticles show potential for use in thermotherapy treatments of various tumours, and the effectiveness of radiofrequency ablation can be enhanced with nanoparticle chemotherapy agents. In vascular intervention, much work is focused on prevention of restenosis through developments in stent technology and systems for localised drug delivery to vessel walls. Further areas of interest include applications for thrombolysis and haemostasis.

  15. Nanotechnology and its Relationship to Interventional Radiology. Part II: Drug Delivery, Thermotherapy, and Vascular Intervention.

    LENUS (Irish Health Repository)

    Power, Sarah

    2010-09-16

    Nanotechnology can be defined as the design, creation, and manipulation of structures on the nanometer scale. This two-part review is intended to acquaint the interventionalist with the field of nanotechnology, and provide an overview of potential applications, while highlighting advances relevant to interventional radiology. Part 2 of the article concentrates on drug delivery, thermotherapy, and vascular intervention. In oncology, advances in drug delivery allow for improved efficacy, decreased toxicity, and greater potential for targeted therapy. Magnetic nanoparticles show potential for use in thermotherapy treatments of various tumours, and the effectiveness of radiofrequency ablation can be enhanced with nanoparticle chemotherapy agents. In vascular intervention, much work is focused on prevention of restenosis through developments in stent technology and systems for localised drug delivery to vessel walls. Further areas of interest include applications for thrombolysis and haemostasis.

  16. Imaging of juvenile spondyloarthritis. Part II: Ultrasonography and magnetic resonance imaging

    Directory of Open Access Journals (Sweden)

    Iwona Sudoł-Szopińska

    2017-09-01

    Full Text Available Juvenile spondyloarthropathies are mainly manifested by symptoms of peripheral arthritis and enthesitis. Early involvement of sacroiliac joints and spine is exceptionally rare in children; this usually happens in adulthood. Conventional radiographs visualize late inflammatory lesions. Early diagnosis is possible with the use of ultrasonography and magnetic resonance imaging. The first part of the article presented classifications and radiographic presentation of juvenile spondyloarthropathies. This part discusses changes seen on ultrasonography and magnetic resonance imaging. In patients with juvenile spondyloarthropathies, these examinations are conducted to diagnose inflammatory lesions in peripheral joints, tendon sheaths, tendons and bursae. Moreover, magnetic resonance also shows subchondral bone marrow edema, which is considered an early sign of inflammation. Ultrasonography and magnetic resonance imaging do not show specific lesions for any rheumatic disease. Nevertheless, they are conducted for early diagnosis, treatment monitoring and identifying complications. This article presents a spectrum of inflammatory changes and discusses the diagnostic value of ultrasonography and magnetic resonance imaging.

  17. Computational and experimental prediction of dust production in pebble bed reactors, Part II

    Energy Technology Data Exchange (ETDEWEB)

    Hiruta, Mie; Johnson, Gannon [Department of Mechanical Engineering, University of Idaho, 1776 Science Center Drive, Idaho Falls, ID 83401 (United States); Rostamian, Maziar, E-mail: mrostamian@asme.org [Department of Mechanical Engineering, University of Idaho, 1776 Science Center Drive, Idaho Falls, ID 83401 (United States); Potirniche, Gabriel P. [Department of Mechanical Engineering, University of Idaho, 1776 Science Center Drive, Idaho Falls, ID 83401 (United States); Ougouag, Abderrafi M. [Idaho National Laboratory, 2525 N Fremont Avenue, Idaho Falls, ID 83401 (United States); Bertino, Massimo; Franzel, Louis [Department of Physics, Virginia Commonwealth University, Richmond, VA 23284 (United States); Tokuhiro, Akira [Department of Mechanical Engineering, University of Idaho, 1776 Science Center Drive, Idaho Falls, ID 83401 (United States)

    2013-10-15

    Highlights: • Custom-built high temperature, high pressure tribometer is designed. • Two different wear phenomena at high temperatures are observed. • Experimental wear results for graphite are presented. • The graphite wear dust production in a typical Pebble Bed Reactor is predicted. -- Abstract: This paper is the continuation of Part I, which describes the high temperature and high pressure helium environment wear tests of graphite–graphite in frictional contact. In the present work, it has been attempted to simulate a Pebble Bed Reactor core environment as compared to Part I. The experimental apparatus, which is a custom-designed tribometer, is capable of performing wear tests at PBR relevant higher temperatures and pressures under a helium environment. This environment facilitates prediction of wear mass loss of graphite as dust particulates from the pebble bed. The experimental results of high temperature helium environment are used to anticipate the amount of wear mass produced in a pebble bed nuclear reactor.

  18. Computational and experimental prediction of dust production in pebble bed reactors, Part II

    Energy Technology Data Exchange (ETDEWEB)

    Mie Hiruta; Gannon Johnson; Maziar Rostamian; Gabriel P. Potirniche; Abderrafi M. Ougouag; Massimo Bertino; Louis Franzel; Akira Tokuhiro

    2013-10-01

    This paper is the continuation of Part I, which describes the high temperature and high pressure helium environment wear tests of graphite–graphite in frictional contact. In the present work, it has been attempted to simulate a Pebble Bed Reactor core environment as compared to Part I. The experimental apparatus, which is a custom-designed tribometer, is capable of performing wear tests at PBR relevant higher temperatures and pressures under a helium environment. This environment facilitates prediction of wear mass loss of graphite as dust particulates from the pebble bed. The experimental results of high temperature helium environment are used to anticipate the amount of wear mass produced in a pebble bed nuclear reactor.

  19. A review on fault classification methodologies in power transmission systems: Part-II

    Directory of Open Access Journals (Sweden)

    Avagaddi Prasad

    2018-05-01

    Full Text Available The countless extent of power systems and applications requires the improvement in suitable techniques for the fault classification in power transmission systems, to increase the efficiency of the systems and to avoid major damages. For this purpose, the technical literature proposes a large number of methods. The paper analyzes the technical literature, summarizing the most important methods that can be applied to fault classification methodologies in power transmission systems.The part 2 of the article is named “A review on fault classification methodologies in power transmission systems”. In this part 2 we discussed the advanced technologies developed by various researchers for fault classification in power transmission systems. Keywords: Transmission line protection, Protective relaying, Soft computing techniques

  20. Autonomy, consent and responsibility. Part II. Informed consent in medical care and in the law.

    Science.gov (United States)

    Mellado, J M

    Legal recognition of patient's rights aspired to change clinical relationship and medical lex artis. However, its implementation has been hampered by the scarcity of resources and the abundance of regulations. For several years, autonomy, consent, and responsibility have formed one of the backbones of the medical profession. However, they have sparked controversy and professional discomfort. In the first part of this article, we examine the conceptual and regulatory limitations of the principle of autonomy as the basis of informed consent. We approach the subject from philosophical, historical, legal, bioethical, deontological, and professional standpoints. In the second part, we cover the viability of informed consent in health care and its relationship with legal responsibility. Copyright © 2016 SERAM. Publicado por Elsevier España, S.L.U. All rights reserved.

  1. Visual servoing in medical robotics: a survey. Part II: tomographic imaging modalities--techniques and applications.

    Science.gov (United States)

    Azizian, Mahdi; Najmaei, Nima; Khoshnam, Mahta; Patel, Rajni

    2015-03-01

    Intraoperative application of tomographic imaging techniques provides a means of visual servoing for objects beneath the surface of organs. The focus of this survey is on therapeutic and diagnostic medical applications where tomographic imaging is used in visual servoing. To this end, a comprehensive search of the electronic databases was completed for the period 2000-2013. Existing techniques and products are categorized and studied, based on the imaging modality and their medical applications. This part complements Part I of the survey, which covers visual servoing techniques using endoscopic imaging and direct vision. The main challenges in using visual servoing based on tomographic images have been identified. 'Supervised automation of medical robotics' is found to be a major trend in this field and ultrasound is the most commonly used tomographic modality for visual servoing. Copyright © 2014 John Wiley & Sons, Ltd.

  2. How to succeed in science: a concise guide for young biomedical scientists. Part II: making discoveries.

    Science.gov (United States)

    Yewdell, Jonathan W

    2008-06-01

    Making discoveries is the most important part of being a scientist, and also the most fun. Young scientists need to develop the experimental and mental skill sets that enable them to make discoveries, including how to recognize and exploit serendipity when it strikes. Here, I provide practical advice to young scientists on choosing a research topic, designing, performing and interpreting experiments and, last but not least, on maintaining your sanity in the process.

  3. How to succeed in science: a concise guide for young biomedical scientists. Part II: making discoveries

    OpenAIRE

    Yewdell, Jonathan W.

    2008-01-01

    Making discoveries is the most important part of being a scientist, and also the most fun. Young scientists need to develop the experimental and mental skill sets that enable them to make discoveries, including how to recognize and exploit serendipity when it strikes. Here, I provide practical advice to young scientists on choosing a research topic, designing, performing and interpreting experiments and, last but not least, on maintaining your sanity in the process.

  4. Nuclear energy and public safety (Part II): a bibliography of technical resources

    International Nuclear Information System (INIS)

    Gabriel, M.R.

    1982-01-01

    Part 2 of the bibliography focuses on technical information of interest to those concerned with the operation of nuclear power plants and the subjects of safety and accidents. A subject index included after the bibliography provides a breakdown of the references into seven categories. There is also an author index. The material cited is available through the National Technical Information Service (NTIS) in Springfield, Virginia

  5. A survey on control schemes for distributed solar collector fields. Part II: Advanced control approaches

    Energy Technology Data Exchange (ETDEWEB)

    Camacho, E.F.; Rubio, F.R. [Universidad de Sevilla, Escuela Superior de Ingenieros, Departamento de Ingenieria de Sistemas y Automatica, Camino de Los Descubrimientos s/n, E-41092 Sevilla (Spain); Berenguel, M. [Universidad de Almeria, Departamento de Lenguajes y Computacion, Area de Ingenieria de Sistemas y Automatica, Carretera Sacramento s/n, E-04120 La Canada, Almeria (Spain); Valenzuela, L. [Plataforma Solar de Almeria - CIEMAT, Carretera Senes s/n, P.O. Box 22, E-04200 Tabernas (Almeria) (Spain)

    2007-10-15

    This article presents a survey of the different advanced automatic control techniques that have been applied to control the outlet temperature of solar plants with distributed collectors during the last 25 years. A classification of the modeling and control approaches described in the first part of this survey is used to explain the main features of each strategy. The treated strategies range from classical advanced control strategies to those with few industrial applications. (author)

  6. FORMATION OF TOILET HABITS IN CHILDREN IN MOSCOW. RETROSPECTIVE STUDY RESULTS. PART II

    Directory of Open Access Journals (Sweden)

    G. A. Karkashadze

    2013-01-01

    Full Text Available The results of the first Russian study of toilet habits formation in children have been obtained. The article was planned to be published in 2 subsequent parts due to the extensiveness of the material. This article is the 2nd part*. It presents and comments on the remaining part of results in the form of the connection between main parameters and characteristics of toilet habits training processes and physiological, psychological and social factors; it also presents the discussion and conclusions. Comparative data (with foreign studies is given. A multitude of both physiological and social factors affect the process of children’s toilet habits training. The following physiological factors have been revealed: stool frequency, physiological involuntary night urination, peculiarities of falling asleep and pernicious habits – processes, which reflect the intestinal motility regulation and defecation states, urination control and neuropsychic activity. The selected training strategy and tactics, style of communication with a child also affect the training process. The most influential family-social factors in terms of toilet habits training processes are: two- or one-parent family, mother’s education and twins in the family. 

  7. PIO I-II tendencies case study. Part 1. Mathematical modeling

    Directory of Open Access Journals (Sweden)

    Adrian TOADER

    2010-03-01

    Full Text Available In the paper, a study is performed from the perspective of giving a method to reduce the conservatism of the well known PIO (Pilot-Induced Oscillation criteria in predicting the susceptibility of an aircraft to this very harmful phenomenon. There are three interacting components of a PIO – the pilot, the vehicle, and the trigger (in fact, the hazard. The study, conceived in two parts, aims to underline the importance of human pilot model involved in analysis. In this first part, it is shown, following classical sources, how the LQG theory of control and estimation is used to obtain a complex model of human pilot. The approach is based on the argument, experimentally proved, that the human behaves “optimally” in some sense, subject to his inherent psychophysical limitations. The validation of such model is accomplished based on the experimental model of a VTOL-type aircraft. Then, the procedure of inserting typical saturation nonlinearities in the open loop transfer function is presented. A second part of the paper will illustrate PIO tendencies evaluation by means of a grapho-analytic method.

  8. History of internal fixation with plates (part 2): new developments after World War II; compressing plates and locked plates.

    Science.gov (United States)

    Hernigou, Philippe; Pariat, Jacques

    2017-07-01

    The first techniques of operative fracture with plates were developed in the 19th century. In fact, at the beginning these methods consisted of an open reduction of the fracture usually followed by a very unstable fixation. As a consequence, the fracture had to be opened with a real risk of (sometimes lethal) infection, and due to unstable fixation, protection with a cast was often necessary. During the period between World Wars I and II, plates for fracture fixation developed with great variety. It became increasingly recognised that, because a fracture of a long bone normally heals with minimal resorption at the bone ends, this may result in slight shortening and collapse, so a very rigid plate might prevent such collapse. However, as a consequence, delayed healing was observed unless the patient was lucky enough to have the plate break. One way of dealing with this was to use a slotted plate in which the screws could move axially, but the really important advance was recognition of the role of compression. After the first description of compression by Danis with a "coapteur", Bagby and Müller with the AO improved the technique of compression. The classic dynamic compression plates from the 1970s were the key to a very rigid fixation, leading to primary bone healing. Nevertheless, the use of strong plates resulted in delayed union and the osteoporosis, cancellous bone, comminution, and/or pathological bone resulted in some failures due to insufficient stability. Finally, new devices represented by locking plates increased the stability, contributing to the principles of a more biological osteosynthesis while giving enough stability to allow immediate full weight bearing in some patients.

  9. Neutronic Analysis of the 3 MW TRIGA MARK II Research Reactor, Part I: Monte Carlo Simulation

    International Nuclear Information System (INIS)

    Huda, M.Q.; Chakrobortty, T.K.; Rahman, M.; Sarker, M.M.; Mahmood, M.S.

    2003-05-01

    This study deals with the neutronic analysis of the current core configuration of a 3 MW TRIGA MARK II research reactor at Atomic Energy Research Establishment (AERE), Savar, Dhaka, Bangladesh and validation of the results by benchmarking with the experimental, operational and available Final Safety Analysis Report (FSAR) values. The three-dimensional continuous-energy Monte Carlo code MCNP4C was used to develop a versatile and accurate full-core model of the TRIGA core. The model represents in detail all components of the core with literally no physical approximation. All fresh fuel and control elements as well as the vicinity of the core were precisely described. Continuous energy cross-section data from ENDF/B-VI and S(α, β) scattering functions from the ENDF/B-V library were used. The validation of the model against benchmark experimental results is presented. The MCNP predictions and the experimentally determined values are found to be in very good agreement, which indicates that the Monte Carlo model is correctly simulating the TRIGA reactor. (author)

  10. Investigation of mixed mode - I/II fracture problems - Part 1: computational and experimental analyses

    Directory of Open Access Journals (Sweden)

    O. Demir

    2016-01-01

    Full Text Available In this study, to investigate and understand the nature of fracture behavior properly under in-plane mixed mode (Mode-I/II loading, three-dimensional fracture analyses and experiments of compact tension shear (CTS specimen are performed under different mixed mode loading conditions. Al 7075-T651 aluminum machined from rolled plates in the L-T rolling direction (crack plane is perpendicular to the rolling direction is used in this study. Results from finite element analyses and fracture loads, crack deflection angles obtained from the experiments are presented. To simulate the real conditions in the experiments, contacts are defined between the contact surfaces of the loading devices, specimen and loading pins. Modeling, meshing and the solution of the problem involving the whole assembly, i.e., loading devices, pins and the specimen, with contact mechanics are performed using ANSYSTM. Then, CTS specimen is analyzed separately using a submodeling approach, in which three-dimensional enriched finite elements are used in FRAC3D solver to calculate the resulting stress intensity factors along the crack front. Having performed the detailed computational and experimental studies on the CTS specimen, a new specimen type together with its loading device is also proposed that has smaller dimensions compared to the regular CTS specimen. Experimental results for the new specimen are also presented.

  11. Reliability of a new biokinetic model of zirconium in internal dosimetry: part II, parameter sensitivity analysis.

    Science.gov (United States)

    Li, Wei Bo; Greiter, Matthias; Oeh, Uwe; Hoeschen, Christoph

    2011-12-01

    The reliability of biokinetic models is essential for the assessment of internal doses and a radiation risk analysis for the public and occupational workers exposed to radionuclides. In the present study, a method for assessing the reliability of biokinetic models by means of uncertainty and sensitivity analysis was developed. In the first part of the paper, the parameter uncertainty was analyzed for two biokinetic models of zirconium (Zr); one was reported by the International Commission on Radiological Protection (ICRP), and one was developed at the Helmholtz Zentrum München-German Research Center for Environmental Health (HMGU). In the second part of the paper, the parameter uncertainties and distributions of the Zr biokinetic models evaluated in Part I are used as the model inputs for identifying the most influential parameters in the models. Furthermore, the most influential model parameter on the integral of the radioactivity of Zr over 50 y in source organs after ingestion was identified. The results of the systemic HMGU Zr model showed that over the first 10 d, the parameters of transfer rates between blood and other soft tissues have the largest influence on the content of Zr in the blood and the daily urinary excretion; however, after day 1,000, the transfer rate from bone to blood becomes dominant. For the retention in bone, the transfer rate from blood to bone surfaces has the most influence out to the endpoint of the simulation; the transfer rate from blood to the upper larger intestine contributes a lot in the later days; i.e., after day 300. The alimentary tract absorption factor (fA) influences mostly the integral of radioactivity of Zr in most source organs after ingestion.

  12. Interaction of Zn(II) with hematite nanoparticles and microparticles: Part 2. ATR-FTIR and EXAFS study of the aqueous Zn(II)/oxalate/hematite ternary system.

    Science.gov (United States)

    Ha, Juyoung; Trainor, Thomas P; Farges, François; Brown, Gordon E

    2009-05-19

    Sorption of Zn(II) to hematite nanoparticles (HN) (av diam=10.5 nm) and microparticles (HM) (av diam=550 nm) was studied in the presence of oxalate anions (Ox2-(aq)) in aqueous solutions as a function of total Zn(II)(aq) to total Ox2-(aq) concentration ratio (R=[Zn(II)(aq)]tot/[Ox2-(aq)]tot) at pH 5.5. Zn(II) uptake is similar in extent for both the Zn(II)/Ox/HN and Zn(II)/Ox/HM ternary systems and the Zn(II)/HN binary system at [Zn(II)(aq)](tot)system than for the Zn(II)/Ox/HM ternary and the Zn(II)/HN and Zn(II)/HM binary systems at [Zn(II)(aq)]tot>4 mM. In contrast, Zn(II) uptake for the Zn(II)/HM binary system is a factor of 2 greater than that for the Zn(II)/Ox/HM and Zn(II)/Ox/HN ternary systems and the Zn(II)/HN binary system at [Zn(II)(aq)]totternary system at both R values examined (0.16 and 0.68), attenuated total reflectance Fourier transform infrared (ATR-FTIR) results are consistent with the presence of inner-sphere oxalate complexes and outer-sphere ZnOx(aq) complexes, and/or type A ternary complexes. In addition, extended X-ray absorption fine structure (EXAFS) spectroscopic results suggest that type A ternary surface complexes (i.e., >O2-Zn-Ox) are present. In the Zn(II)/Ox/HN ternary system at R=0.15, ATR-FTIR results indicate the presence of inner-sphere oxalate and outer-sphere ZnOx(aq) complexes; the EXAFS results provide no evidence for inner-sphere Zn(II) complexes or type A ternary complexes. In contrast, ATR-FTIR results for the Zn/Ox/HN sample with R = 0.68 are consistent with a ZnOx(s)-like surface precipitate and possibly type B ternary surface complexes (i.e., >O2-Ox-Zn). EXAFS results are also consistent with the presence of ZnOx(s)-like precipitates. We ascribe the observed increase of Zn(II)(aq) uptake in the Zn(II)/Ox/HN ternary system at [Zn(II)(aq)]tot>or=4 mM relative to the Zn(II)/Ox/HM ternary system to formation of a ZnOx(s)-like precipitate at the hematite nanoparticle/water interface.

  13. Experimental investigation and numerical modeling of carbonation process in reinforced concrete structures Part II. Practical applications

    International Nuclear Information System (INIS)

    Saetta, Anna V.; Vitaliani, Renato V.

    2005-01-01

    The mathematical-numerical method developed by the authors to predict the corrosion initiation time of reinforced concrete structures due to carbonation process, recalled in Part I of this work, is here applied to some real cases. The final aim is to develop and test a practical method for determining the durability characteristics of existing buildings liable to carbonation, as well as estimating the corrosion initiation time of a building at the design stage. Two industrial sheds with different ages and located in different areas have been analyzed performing both experimental tests and numerical analyses. Finally, a case of carbonation-induced failure in a prestressed r.c. beam is presented

  14. The role of the illegality factor in the taxation of income. Part II

    OpenAIRE

    Čerka, Paulius; Gudynienė, Lina

    2012-01-01

    The taxation of illegal income is quite common in many foreign countries, but this practice is not yet applicable in Lithuania, though the recent movements of Lithuania’s Finance Minister, when she admitted that all income should be taxed despite it’s source show her positive attitude towards the taxation of illegal income. The article promotes the idea that all personal income, despite its source, should be taxed.The article is divided into two parts: the first one, which is not published he...

  15. A rare sugar xylitol. Part II: biotechnological production and future applications of xylitol.

    Science.gov (United States)

    Granström, Tom Birger; Izumori, Ken; Leisola, Matti

    2007-02-01

    Xylitol is the first rare sugar that has global markets. It has beneficial health properties and represents an alternative to current conventional sweeteners. Industrially, xylitol is produced by chemical hydrogenation of D-xylose into xylitol. The biotechnological method of producing xylitol by metabolically engineered yeasts, Saccharomyces cerevisiae or Candida, has been studied as an alternative to the chemical method. Due to the industrial scale of production, xylitol serves as an inexpensive starting material for the production of other rare sugars. The second part of this mini-review on xylitol will look more closely at the biotechnological production and future applications of the rare sugar, xylitol.

  16. Synchrotron radiation and x-ray topography. Part II. Examples of some applications

    International Nuclear Information System (INIS)

    Bilello, J.C.

    1985-01-01

    Synchrotron x-radiation topography is a powerful tool for studying defects in ''bulk'' metals and alloys. The general features of this technique, including both advantages and disadvantages, have been discussed in Part I of this review. This second report concentrates on some applications of the white beam topography method to studies of flow and fracture of materials and indicates fruitful areas for possible future application. Research investigations on cleavage surfaces of some bcc and hcp metals and alloys are reviewed and contrasted to other more usual methods of studying the morphology of the resulting microstructures

  17. Psychopathy, violence and crime: a psychological-forensic, psychiatric-legal and criminological analysis (Part II)

    OpenAIRE

    Pozueco Romero, J.M.; Romero Guillena, S.L.; Casas Barquero, N.

    2011-01-01

    La Jurisprudencia española se encuentra frecuentemente ante dictámenes periciales en los que aparecen términos como psicópata, trastorno antisocial de la personalidad, personalidad psicopática, psicópata desalmado, psicopatía epileptoide, sociopatía, etc. De esta forma, no es infrecuente que los juristas (magistrados, jueces, fiscales, abogados) se hallen desorientados ante tanta terminología que, pese a todo, en absoluto se constituyen en sinónimos. La Doctrina, por su parte, disiente de la ...

  18. Numerical modelling of flexible pavement incorporating cross-anisotropic material properties. Part II: Surface rectangular loading

    OpenAIRE

    Maina, J W; Kawana, F; Matsui, K

    2017-01-01

    In order to better understand the impact of increased loading on roads, studies on tyre-road interaction have gained prominence in recent years. Tyres form an essential interface between vehicles and road pavement surfaces. These are the only parts of the vehicle that are in contact with the road and transmit the vehicle loading to the road surface. The use of the Cartesian coordinate system is convenient in dealing with a uniform/non-uniform tyre load acting over a rectangular area, but few ...

  19. Modification of Concrete Damaged Plasticity model. Part II: Formulation and numerical tests

    Directory of Open Access Journals (Sweden)

    Kamińska Inez

    2017-01-01

    Full Text Available A refined model for elastoplastic damaged material is formulated based on the plastic potential introduced in Part I [1]. Considered model is an extension of Concrete Damaged Plasticity material implemented in Abaqus [2]. In the paper the stiffness tensor for elastoplastic damaged behaviour is derived. In order to validate the model, computations for the uniaxial tests are performed. Response of the model for various cases of parameter’s choice is shown and compared to the response of the CDP model.

  20. [Homicides in East Berlin from 1980 to 1989. Part II: results of investigations and legal consequences].

    Science.gov (United States)

    Wirth, Ingo; Strauch, Hansjürg

    2007-01-01

    The second part of the study on homicides in East Berlin from 1980 to 1989 describes the solving of crimes, the usual features of offenders and the legal assessment according to East German law. Of the 139 homicides 126 crimes (= 90.6%) could be solved. Most of the offenders had a low social background and often belonged to the victim's circle of friends or family. Situational homicides and elimination crimes were the most common crimes. In the legal assessment sentences for murder were predominant.

  1. π+p, π+n, and π+d interactions. A compilation. Part II

    International Nuclear Information System (INIS)

    Chew, D.M.; Henri, V.P.; Lasinski, T.A.; Trippe, T.G.; Uchiyama, F.; Winkelmann, F.C.

    1973-05-01

    A listing is presented of the 297 articles from which the data in Part I were abstracted. These listings contain additional information on each of these articles: authors, title, abstract, closely related references, beam, momenta of experiment, target, etc. One also gives tables of the data as they appeared in the original articles. Systematic comments are made specifying how the final data were obtained; for example, mass cuts for resonance production cross sections, spectator momentum cuts, corrections for systematic biases, etc. This information, extracted from the papers, is given to aid the reader in his evaluation of the results and in any comparison with other experiments

  2. The year 2014 in the European Heart Journal--Cardiovascular Imaging: part II.

    Science.gov (United States)

    Gerber, Bernhard L; Edvardsen, Thor; Pierard, Luc A; Saraste, Antti; Knuuti, Juhani; Maurer, Gerald; Habib, Gilbert; Lancellotti, Patrizio

    2015-11-01

    The European Heart Journal-Cardiovascular Imaging, created in 2012, has become a reference for publishing multimodality cardiovascular imaging scientific and review papers. The impressive 2014 impact factor of 4.105 confirms the important position of our journal. In this part, we summarize the most important studies from the journal's third year, with specific emphasis on cardiomyopathies, congenital heart diseases, valvular heart diseases, and heart failure. Published on behalf of the European Society of Cardiology. All rights reserved. © The Author 2015. For permissions please email: journals.permissions@oup.com.

  3. Investigation of novel propulsion systems – the exoskeletal engine concept. Part II

    Directory of Open Access Journals (Sweden)

    Iulian JUHASZ

    2011-06-01

    Full Text Available The exoskeletal engine represents a relatively new concept in the world of propulsion systems. It is a drum-rotor engine concept in which conventionally heavy shafts and discs are eliminated and replaced by rotating casings that support the blades in span wise compression. Thus the rotating blades are in compression rather than in tension. The resulting open channel at the engine centerline has immense potential for jet noise reduction and can also accommodate an inner combined-cycle thruster such as a ramjet. This is the second part of the article.

  4. El reduccionismo científico y el control de las conciencias. Parte II

    OpenAIRE

    Leonardo Viniegra Velázquez

    2014-01-01

    En esta segunda parte se analizan los vínculos de subordinación del quehacer científico con lo que se designa como la lógica del poder y la dominación, a través de dar prioridad absoluta a los hechos sobre las ideas y favorecer el conocimiento capitalizable por la innovación tecnológica, la cual es decisiva en la rentabilidad y competitividad de las grandes empresas (los intereses de lucro que gobiernan el planeta), y base de los mecanismos de control político-social de las conciencias y de l...

  5. Nutrition of preterm infants with bronchopulmonary dysplasia after hospital discharge – Part II

    Directory of Open Access Journals (Sweden)

    Hercília Guimarães

    2014-01-01

    Full Text Available Preterm infants with bronchopulmonary dysplasia often present with severe growth failure at discharge from the neonatal intensive care unit. Catch-up growth accelerates after hospital discharge, nevertheless, feeding problems may need a specialized approach. Following the revision of the scientific literature on the most relevant aspects on nutrition of patients with bronchopulmonary dysplasia after hospital discharge in Part I, in this article the Authors present and discuss important issues such as catch up growth, swallow dysfunction, gastroesophageal reflux, and how to improve feeding competences.

  6. Coupled Vibration of Unshrouded Centrifugal Compressor Impellers. Part II: Computation of Vibration Behavior

    Directory of Open Access Journals (Sweden)

    Dirk Hagelstein

    2000-01-01

    Full Text Available The increased use of small gas turbines and turbochargers in different technical fields has led to the development of highly-loaded centrifugal compressors with extremely thin blades. Due to high rotational speed and the correspondingly high centrifugal loads, the shape of the impeller hub must also be optimized. This has led to a reduction of the thickness of the impeller disc in the outlet region. The thin parts of the impeller are very sensitive and may be damaged by the excitation of dangerous blade vibrations.

  7. Transonic Airfoil Flow Simulation. Part II: Inviscid-Viscous Coupling Scheme

    Directory of Open Access Journals (Sweden)

    Vladimir CARDOŞ

    2010-09-01

    Full Text Available A calculation method for the subsonic and transonic viscous flow over airfoil using the displacement surface concept is described. This modelling technique uses a finite volume method for the time-dependent Euler equations and laminar and turbulent boundary-layer integral methods. In additional special models for transition, laminar or turbulent separation bubbles and trailing edge treatment have been selected. However, the flow is limited to small parts of trailing edge-type separation. Comparisons with experimental data and other methods are shown.

  8. CPM Pairs from LSPM so far not WDS Listed – Part II

    Science.gov (United States)

    Knapp, Wilfried; Nanson, John

    2017-10-01

    The LSPM catalog (Lepine and Shara 2005) is a rich source for CPM pairs we thought already exhausted – but as we found during research for our report “A new concept for counter-checking of assumed CPM pairs” (Knapp and Nanson 2017) there are still many poten-tial CPM pairs indicated in LSPM which as of the end of 2016 are not listed in the WDS cata-log. After our first part on about 40 such objects (Knapp and Nanson 2017) the next report with about 30 additional common proper motion pairs is presented here.

  9. From atactic to isotactic CO/p-methylstyrene copolymer by proper modification of Pd(II) catalysts bearing achiral alpha-diimines.

    Science.gov (United States)

    Binotti, Barbara; Carfagna, Carla; Zuccaccia, Cristiano; Macchioni, Alceo

    2005-01-07

    Cationic Pd(II) complexes modified with achiral C(2v)-symmetric alpha-diimine ligands allow preparation of atactic or isotactic stereoblock CO/p-methylstyrene copolymers; both catalyst activity and polyketone microstructure depend on the choice of alpha-diimine substituents and counterion.

  10. Ruthenium(II) bipyridine complexes bearing quinoline-azoimine (NN'N″) tridentate ligands: synthesis, spectral characterization, electrochemical properties and single-crystal X-ray structure analysis.

    Science.gov (United States)

    Al-Noaimi, Mousa; Abdel-Rahman, Obadah S; Fasfous, Ismail I; El-khateeb, Mohammad; Awwadi, Firas F; Warad, Ismail

    2014-05-05

    Four octahedral ruthenium(II) azoimine-quinoline complexes having the general molecular formula [Ru(II)(L-Y)(bpy)Cl](PF6) {L-Y=YC6H4N=NC(COCH3)=NC9H6N, Y=H (1), CH3 (2), Br (3), NO2 (4) and bpy=2,2'-bipyrdine} were synthesized. The azoimine-quinoline based ligands behave as NN'N″ tridentate donors and coordinated to ruthenium via azo-N', imine-N' and quinolone-N″ nitrogen atoms. The composition of the complexes has been established by elemental analysis, spectral methods (FT-IR, electronic, (1)H NMR, UV/Vis and electrochemical (cyclic voltammetry) techniques. The crystal structure of complex 1 is reported. The Ru(II) oxidation state is greatly stabilized by the novel tridentate ligands, showing Ru(III/II) couples ranging from 0.93-1.27 V vs. Cp2Fe/Cp2Fe(+). The absorption spectrum of 1 in dichloromethane was modeled by time-dependent density functional theory (TD-DFT). Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Short stack modeling of degradation in solid oxide fuel cells. Part II. Sensitivity and interaction analysis

    Science.gov (United States)

    Gazzarri, J. I.; Kesler, O.

    In the first part of this two-paper series, we presented a numerical model of the impedance behaviour of a solid oxide fuel cell (SOFC) aimed at simulating the change in the impedance spectrum induced by contact degradation at the interconnect-electrode, and at the electrode-electrolyte interfaces. The purpose of that investigation was to develop a non-invasive diagnostic technique to identify degradation modes in situ. In the present paper, we appraise the predictive capabilities of the proposed method in terms of its robustness to uncertainties in the input parameters, many of which are very difficult to measure independently. We applied this technique to the degradation modes simulated in Part I, in addition to anode sulfur poisoning. Electrode delamination showed the highest robustness to input parameter variations, followed by interconnect oxidation and interconnect detachment. The most sensitive degradation mode was sulfur poisoning, due to strong parameter interactions. In addition, we simulate several simultaneous two-degradation-mode scenarios, assessing the method's capabilities and limitations for the prediction of electrochemical behaviour of SOFC's undergoing multiple simultaneous degradation modes.

  12. Short stack modeling of degradation in solid oxide fuel cells. Part II. Sensitivity and interaction analysis

    Energy Technology Data Exchange (ETDEWEB)

    Gazzarri, J.I. [Department of Mechanical Engineering, University of British Columbia, 2054-6250 Applied Science Lane, Vancouver, BC V6T 1Z4 (Canada); Kesler, O. [Department of Mechanical and Industrial Engineering, University of Toronto, 5 King' s College Road, Toronto, ON M5S 3G8 (Canada)

    2008-01-21

    In the first part of this two-paper series, we presented a numerical model of the impedance behaviour of a solid oxide fuel cell (SOFC) aimed at simulating the change in the impedance spectrum induced by contact degradation at the interconnect-electrode, and at the electrode-electrolyte interfaces. The purpose of that investigation was to develop a non-invasive diagnostic technique to identify degradation modes in situ. In the present paper, we appraise the predictive capabilities of the proposed method in terms of its robustness to uncertainties in the input parameters, many of which are very difficult to measure independently. We applied this technique to the degradation modes simulated in Part I, in addition to anode sulfur poisoning. Electrode delamination showed the highest robustness to input parameter variations, followed by interconnect oxidation and interconnect detachment. The most sensitive degradation mode was sulfur poisoning, due to strong parameter interactions. In addition, we simulate several simultaneous two-degradation-mode scenarios, assessing the method's capabilities and limitations for the prediction of electrochemical behaviour of SOFC's undergoing multiple simultaneous degradation modes. (author)

  13. 2012 in review - part II: overcoming the obstacles in the pharma/biotech industry.

    Science.gov (United States)

    Rabasseda, X; Dulsat, C; Navarro, D; Cruces, E; Graul, A I; Jago, C; Tracy, M

    2013-02-01

    As highlighted in the first part of this review published last month, the year 2012 saw the approval of a remarkable number of new drugs, and among the new drugs reaching the market, a significant proportion were orphan drugs developed for treating less prevalent diseases. These drugs are certainly not expected to become blockbusters, but are of high interest because of their efficacy in a narrow spectrum of patients. This trend aligns with the general tendency of staying away from fit-for-all blockbusters into personalized medicine as one of the strategies for overcoming the patent cliff that resulted in a long list of drugs going off patent and being approved as generics also during last year. The emerging scenario resulting from new developments in the form of new drugs and biosimilars and newly available generic medications paralleled by strategic movements within the pharmaceutical industry to reinforce their position in the market, as reflected by merger and acquisition deals accompanied by significant efforts into prioritization resulting in spin-off and split transactions, is reviewed in this second part. This paper includes a significant amount of data in tables for quick review and to profile the new strategic movements in drug pipelines. Further information, including details on mechanisms of action, current status, itemized pharmacology, pharmacokinetic and clinical trial research findings and updated information can be found in the proprietary databases Thomson Reuters Integrity(SM) and Thomson Reuters Cortellis™. Copyright 2013 Prous Science, S.A.U. or its licensors. All rights reserved.

  14. Prediction of 222 Rn exhalation rates from phosphogypsum based stacks. Part II: preliminary numerical results

    International Nuclear Information System (INIS)

    Rabi, Jose A.; Mohamad, Abdulmajeed A.

    2004-01-01

    The first part of this paper proposes a steady-state 2-D model for 222 Rn transport in phosphogypsum stacks. In this second part, the dimensionless model equations are solved numerically with the help of an existing finite-volume simulator that has been successfully used to solve heat and mass transfer problems in porous media. As a test case, a rectangular shaped stack is considered in order to verify the ability of the proposed parametric approach to account for concurrent effects on the 222 Rn exhalation into the local atmosphere. Air flow is supposed to be strictly buoyancy driven and the ground is assumed to be impermeable to 222 Rn and at a higher temperature under the stack base. Dimensionless controlling parameters are set to representative values and results are presented for Grashof number in the range 10 6 ≤Gr≤ 10 8 , corresponding to very small to small temperature differences between incoming air and ground underneath the stack base. For the particular set of parameters and inasmuch as Gr increases, streamlines presented basically the same pattern while internal isotherms and iso concentration lines remained almost unchanged. Total average Sherwood number proved to be rather insensitive to Gr while total average Nusselt increased slightly with Gr. (author)

  15. Retrieving Storm Electric Fields from Aircrfaft Field Mill Data: Part II: Applications

    Science.gov (United States)

    Koshak, William; Mach, D. M.; Christian H. J.; Stewart, M. F.; Bateman M. G.

    2006-01-01

    The Lagrange multiplier theory developed in Part I of this study is applied to complete a relative calibration of a Citation aircraft that is instrumented with six field mill sensors. When side constraints related to average fields are used, the Lagrange multiplier method performs well in computer simulations. For mill measurement errors of 1 V m(sup -1) and a 5 V m(sup -1) error in the mean fair-weather field function, the 3D storm electric field is retrieved to within an error of about 12%. A side constraint that involves estimating the detailed structure of the fair-weather field was also tested using computer simulations. For mill measurement errors of 1 V m(sup -l), the method retrieves the 3D storm field to within an error of about 8% if the fair-weather field estimate is typically within 1 V m(sup -1) of the true fair-weather field. Using this type of side constraint and data from fair-weather field maneuvers taken on 29 June 2001, the Citation aircraft was calibrated. Absolute calibration was completed using the pitch down method developed in Part I, and conventional analyses. The resulting calibration matrices were then used to retrieve storm electric fields during a Citation flight on 2 June 2001. The storm field results are encouraging and agree favorably in many respects with results derived from earlier (iterative) techniques of calibration.

  16. Differentially Encoded LDPC Codes—Part II: General Case and Code Optimization

    Directory of Open Access Journals (Sweden)

    Li (Tiffany Jing

    2008-01-01

    Full Text Available This two-part series of papers studies the theory and practice of differentially encoded low-density parity-check (DE-LDPC codes, especially in the context of noncoherent detection. Part I showed that a special class of DE-LDPC codes, product accumulate codes, perform very well with both coherent and noncoherent detections. The analysis here reveals that a conventional LDPC code, however, is not fitful for differential coding and does not, in general, deliver a desirable performance when detected noncoherently. Through extrinsic information transfer (EXIT analysis and a modified "convergence-constraint" density evolution (DE method developed here, we provide a characterization of the type of LDPC degree profiles that work in harmony with differential detection (or a recursive inner code in general, and demonstrate how to optimize these LDPC codes. The convergence-constraint method provides a useful extension to the conventional "threshold-constraint" method, and can match an outer LDPC code to any given inner code with the imperfectness of the inner decoder taken into consideration.

  17. Inductively coupled plasma emission spectroscopy. Part II: applications and fundamentals. Volume 2

    International Nuclear Information System (INIS)

    Boumans, P.W.J.M.

    1987-01-01

    This is the second part of the two-volume treatise by this well-known and respected author. This volume reviews applications of inductively coupled plasma atomic emission spectroscopy (ICP-AES), summarizes fundamental studies, and compares ICP-AES methods with other methods of analysis. The first six chapters are devoted to specific fields of application, including the following: metals and other industrial materials, geology, the environment, agriculture and food, biology and clinical analysis, and organic materials. The chapter on the analysis of organic materials also covers the special instrumental considerations required when organic solvents are introduced into an inductively coupled plasma. A chapter on the direct analysis of solids completes the first part of this volume. Each of the applications chapters begins with a summary of the types of samples that are encountered in that field, and the kinds of problems that an elemental analysis can help to solve. This is followed by a tutorial approach covering applicability, advantages, and limitations of the methods. The coverage is thorough, including sample handling, storage, and preparation, acid, and fusion dissolution, avoiding contamination, methods of preconcentration, the types of interferences that can be expected and ways to reduce them, and the types of ICP plasmas that are used. The second half of the volume covers fundamental studies of ICP-AES: basic processes of aerosol generation, plasma modeling and computer simulation, spectroscopic diagnostics, excitation mechanisms, and discharge characteristics. This section introduces the experimental and modeling methods that have been used to obtain fundamental information about ICPs

  18. Quality control for digital mammography: Part II recommendations from the ACRIN DMIST trial

    International Nuclear Information System (INIS)

    Yaffe, Martin J.; Bloomquist, Aili K.; Mawdsley, Gordon E.

    2006-01-01

    The Digital Mammography Imaging Screening Trial (DMIST), conducted under the auspices of the American College of Radiology Imaging Network (ACRIN), is a clinical trial designed to compare the accuracy of digital versus screen-film mammography in a screening population [E. Pisano et al., ACRIN 6652--Digital vs. Screen-Film Mammography, ACRIN (2001)]. Part I of this work described the Quality Control program developed to ensure consistency and optimal operation of the digital equipment. For many of the tests, there were no failures during the 24 months imaging was performed in DMIST. When systems failed, they generally did so suddenly rather than through gradual deterioration of performance. In this part, the utility and effectiveness of those tests are considered. This suggests that after verification of proper operation, routine extensive testing would be of minimal value. A recommended set of tests is presented including additional and improved tests, which we believe meet the intent and spirit of the Mammography Quality Standards Act regulations to ensure that full-field digital mammography systems are functioning correctly, and consistently producing mammograms of excellent image quality

  19. Field Portable Low Temperature Porous Layer Open Tubular Cryoadsorption Headspace Sampling and Analysis Part II: Applications*

    Science.gov (United States)

    Harries, Megan; Bukovsky-Reyes, Santiago; Bruno, Thomas J.

    2016-01-01

    This paper details the sampling methods used with the field portable porous layer open tubular cryoadsorption (PLOT-cryo) approach, described in Part I of this two-part series, applied to several analytes of interest. We conducted tests with coumarin and 2,4,6-trinitrotoluene (two solutes that were used in initial development of PLOT-cryo technology), naphthalene, aviation turbine kerosene, and diesel fuel, on a variety of matrices and test beds. We demonstrated that these analytes can be easily detected and reliably identified using the portable unit for analyte collection. By leveraging efficiency-boosting temperature control and the high flow rate multiple capillary wafer, very short collection times (as low as 3 s) yielded accurate detection. For diesel fuel spiked on glass beads, we determined a method detection limit below 1 ppm. We observed greater variability among separate samples analyzed with the portable unit than previously documented in work using the laboratory-based PLOT-cryo technology. We identify three likely sources that may help explain the additional variation: the use of a compressed air source to generate suction, matrix geometry, and variability in the local vapor concentration around the sampling probe as solute depletion occurs both locally around the probe and in the test bed as a whole. This field-portable adaptation of the PLOT-cryo approach has numerous and diverse potential applications. PMID:26726934

  20. Field portable low temperature porous layer open tubular cryoadsorption headspace sampling and analysis part II: Applications.

    Science.gov (United States)

    Harries, Megan; Bukovsky-Reyes, Santiago; Bruno, Thomas J

    2016-01-15

    This paper details the sampling methods used with the field portable porous layer open tubular cryoadsorption (PLOT-cryo) approach, described in Part I of this two-part series, applied to several analytes of interest. We conducted tests with coumarin and 2,4,6-trinitrotoluene (two solutes that were used in initial development of PLOT-cryo technology), naphthalene, aviation turbine kerosene, and diesel fuel, on a variety of matrices and test beds. We demonstrated that these analytes can be easily detected and reliably identified using the portable unit for analyte collection. By leveraging efficiency-boosting temperature control and the high flow rate multiple capillary wafer, very short collection times (as low as 3s) yielded accurate detection. For diesel fuel spiked on glass beads, we determined a method detection limit below 1 ppm. We observed greater variability among separate samples analyzed with the portable unit than previously documented in work using the laboratory-based PLOT-cryo technology. We identify three likely sources that may help explain the additional variation: the use of a compressed air source to generate suction, matrix geometry, and variability in the local vapor concentration around the sampling probe as solute depletion occurs both locally around the probe and in the test bed as a whole. This field-portable adaptation of the PLOT-cryo approach has numerous and diverse potential applications. Published by Elsevier B.V.

  1. A Review of CAM for Procedural Pain in Infancy: Part II. Other Interventions

    Directory of Open Access Journals (Sweden)

    Jennie C. I. Tsao

    2008-01-01

    Full Text Available This article is the second in a two-part series reviewing the empirical evidence for complementary and alternative medicine (CAM approaches for the management of pain related to medical procedures in infants up to 6 weeks of age. Part I of this series investigated the effects of sucrose with or without non-nutritive sucking (NNS. The present article examines other CAM interventions for procedural pain including music-based interventions, olfactory stimulation, kangaroo care and swaddling. Computerized databases were searched for relevant studies including prior reviews and primary trials. Preliminary support was revealed for the analgesic effects of the CAM modalities reviewed. However, the overall quality of the evidence for these approaches remains relatively weak. Additional well-designed trials incorporating rigorous methodology are required. Such investigations will assist in the development of evidence-based guidelines on the use of CAM interventions either alone or in concert with conventional approaches to provide safe, reliable analgesia for infant procedural pain.

  2. Genetic and epigenetic features in radiation sensitivity. Part II: implications for clinical practice and radiation protection

    International Nuclear Information System (INIS)

    Bourguignon, Michel H.; Gisone, Pablo A.; Perez, Maria R.; Michelin, Severino; Dubner, Diana; Giorgio, Marina di; Carosella, Edgardo D.

    2005-01-01

    Recent progress especially in the field of gene identification and expression has attracted greater attention to the genetic and epigenetic susceptibility to cancer, possibly enhanced by ionising radiation. This issue is especially important for radiation therapists since hypersensitive patients may suffer from adverse effects in normal tissues following standard radiation therapy, while normally sensitive patients could receive higher doses of radiation, offering a better likelihood of cure for malignant tumours. Although only a small percentage of individuals are ''hypersensitive'' to radiation effects, all medical specialists using ionising radiation should be aware of the aforementioned progress in medical knowledge. The present paper, the second of two parts, reviews human disorders known or strongly suspected to be associated with hypersensitivity to ionising radiation. The main tests capable of detecting such pathologies in advance are analysed, and ethical issues regarding genetic testing are considered. The implications for radiation protection of possible hypersensitivity to radiation in a part of the population are discussed, and some guidelines for nuclear medicine professionals are proposed. (orig.)

  3. U3Si2 behavior in H2O environments: Part II, pressurized water with controlled redox chemistry

    Science.gov (United States)

    Nelson, A. T.; Migdisov, A.; Wood, E. Sooby; Grote, C. J.

    2018-03-01

    Recent interest in U3Si2 as an advanced light water reactor fuel has driven assessment of numerous properties, but characterization of its response to H2O environments is sparse in available literature. The behavior of U3Si2 in H2O containing atmospheres is investigated and presented in a two-part series of articles. This work examines the behavior of U3Si2 following exposure to pressurized H2O at temperatures from 300 to 350 °C. Testing was performed using two autoclave configurations and multiple redox conditions. Use of solid state buffers to attain a controlled water chemistry is also presented as a means to test actinide-bearing systems. Buffers were used to vary the hydrogen concentration between 1 and 30 parts per million H2. Testing included UN, U3Si5, and UO2. Both UN and U3Si5 were found to rapidly pulverize in less than 50 h at 300 °C. Uranium dioxide was included as a control for the autoclave system, and was found to be minimally impacted by exposure to pressurized water at the conditions tested for extended time periods. Testing of U3Si2 at 300 °C found reasonable stability through 30 days in 1-5 ppm H2. However, pulverization was observed following 35 days. The redox condition of testing strongly affected pulverization. Characterization of the resulting microstructures suggests that the mechanism responsible for pulverization under more strongly reducing conditions differs from that previously identified. Hydride formation is hypothesized to drive this transition. Testing performed at 350 °C resulted in rapid pulverization of U3Si2 in under 50 h.

  4. Pre-earthquake signals – Part II: Flow of battery currents in the crust

    Directory of Open Access Journals (Sweden)

    F. T. Freund

    2007-09-01

    Full Text Available When rocks are subjected to stress, dormant electronic charge carriers are activated. They turn the stressed rock volume into a battery, from where currents can flow out. The charge carriers are electrons and defect electrons, also known as positive holes or pholes for short. The boundary between stressed and unstressed rock acts as a potential barrier that lets pholes pass but blocks electrons. One can distinguish two situations in the Earth's crust: (i only pholes spread out of a stressed rock volume into the surrounding unstressed rocks. This is expected to lead to a positive surface charge over a wide area around the future epicenter, to perturbations in the ionosphere, to stimulated infrared emission from the ground, to ionization of the near-ground air, to cloud formation and to other phenomena that have been reported to precede major earthquakes. (ii both pholes and electrons flow out of the stressed rock volume along different paths, sideward into the relatively cool upper layers of the crust and downward into the hot lower crust. This situation, which is likely to be realized late in the earthquake preparation process, is necessary for the battery circuit to close and for transient electric currents to flow. If burst-like, these currents should lead to the emission of low frequency electromagnetic radiation. Understanding how electronic charge carriers are stress-activated in rocks, how they spread or flow probably holds the key to deciphering a wide range of pre-earthquake signals. It opens the door to a global earthquake early warning system, provided resources are pooled through a concerted and constructive community effort, including seismologists, with international participation.

  5. Graduate-Assistant Athletic Trainers' Perceptions of the Supervisor's Role in Professional Socialization: Part II.

    Science.gov (United States)

    Thrasher, Ashley B; Walker, Stacy E; Hankemeier, Dorice A; Mulvihill, Thalia

    2016-10-01

    Many new athletic trainers (ATs) obtain graduate-assistant (GA) positions to gain more experience and professional development while being mentored by a veteran AT; however, GA ATs' perceptions of the supervisor's role in professional development are unknown. To explore the supervisor's role in the professional development of GAs in the collegiate setting. Qualitative study. Phone interviews. A total of 19 collegiate GAs (15 women, 4 men; average age = 23 ± 0.15 years; National Collegiate Athletic Association Division I = 13, II = 3, III = 2; National Association of Intercollegiate Athletics = 2; postprofessional athletic training program = 5). Data were collected via phone interviews and transcribed verbatim. Interviews were conducted until data saturation occurred. Data were analyzed through phenomenologic reduction. Trustworthiness was established via member checks and peer review. Three themes emerged: (1) GAs' expectations of supervisors, (2) professional development, and (3) mentoring and support. Participants expected their supervisors to provide mentorship, support, and feedback to help them improve their athletic training skills, but they also realized supervisors were busy with patient care responsibilities. Most participants felt their supervisors were available, but others believed their supervisors were too busy to provide support and feedback. Participants felt their supervisors provided professional development by teaching them new skills and socializing them into the profession. Furthermore, they thought their supervisors provided mentorship professionally, personally, and clinically. Supervisors supported the participants by standing behind them in clinical decisions and having open-door policies. The graduate assistantship allows new ATs to gain experience while pursuing professional development, mentorship, and support from a supervisor. The extent of development is highly dependent on the supervisor, but most supervisors mentor GAs. When

  6. The evolution of the temperature field during cavity collapse in liquid nitromethane. Part II: reactive case

    Science.gov (United States)

    Michael, L.; Nikiforakis, N.

    2018-02-01

    This work is concerned with the effect of cavity collapse in non-ideal explosives as a means of controlling their sensitivity. The main objective is to understand the origin of localised temperature peaks (hot spots) which play a leading order role at the early stages of ignition. To this end, we perform two- and three-dimensional numerical simulations of shock-induced single gas-cavity collapse in liquid nitromethane. Ignition is the result of a complex interplay between fluid dynamics and exothermic chemical reaction. In the first part of this work, we focused on the hydrodynamic effects in the collapse process by switching off the reaction terms in the mathematical formulation. In this part, we reinstate the reactive terms and study the collapse of the cavity in the presence of chemical reactions. By using a multi-phase formulation which overcomes current challenges of cavity collapse modelling in reactive media, we account for the large density difference across the material interface without generating spurious temperature peaks, thus allowing the use of a temperature-based reaction rate law. The mathematical and physical models are validated against experimental and analytic data. In Part I, we demonstrated that, compared to experiments, the generated hot spots have a more complex topological structure and that additional hot spots arise in regions away from the cavity centreline. Here, we extend this by identifying which of the previously determined high-temperature regions in fact lead to ignition and comment on the reactive strength and reaction growth rate in the distinct hot spots. We demonstrate and quantify the sensitisation of nitromethane by the collapse of the isolated cavity by comparing the ignition times of nitromethane due to cavity collapse and the ignition time of the neat material. The ignition in both the centreline hot spots and the hot spots generated by Mach stems occurs in less than half the ignition time of the neat material. We compare

  7. [Cryptogenic stroke - patent foramen ovale - migraine with aura: incidental triad or significant relationship? Part II].

    Science.gov (United States)

    Łukasik, Maria; Kozubski, Wojciech

    2012-01-01

    In the second part of the paper, we discuss the relationship between migraine with aura and either patent foramen ovale (PFO) or stroke. The results of the studies suggest that PFO with right-to-left shunt is more prevalent among patients suffering from migraine with aura. Moreover, migraine with aura is a risk factor for ischaemic stroke in women and the risk increases when they have additional vascular risk factors such as taking oral contraception and smoking. However, the pathophysiology of these phenomena remains hypothetical. The most frequently reported theory suggests paradoxical embolism as a mechanism of the above-mentioned pathologies. In this paper we compare the pros and cons of the general theories. We discuss the percutaneous closure of PFO in patients with migraine, regarding the benefit/risk ratio.

  8. Study of a phase change energy storage using spherical capsules. Part II: Numerical modelling

    International Nuclear Information System (INIS)

    Bedecarrats, J.P.; Castaing-Lasvignottes, J.; Strub, F.; Dumas, J.P.

    2009-01-01

    The objective of this work is the numerical study of an industrial process of energy storage which consists in the use of a cylindrical tank filled with encapsulated phase change materials (PCM). A particularity is present in this kind of processes; it concerns the delay of the crystallization of the PCM, called supercooling phenomenon. The development of the model for cold storage with heat transfer fluid flowing enables a detailed analysis of this process. The effects of different parameters on the behaviour of the tank, such as the inlet temperature, the flow rate, are examined when the tank is in vertical position. There is substantial agreement between the prediction and the experimental values already presented in part I.

  9. The nuclear engineering programmes at the Royal Military College of Canada. Part II

    Energy Technology Data Exchange (ETDEWEB)

    Bonin, H.W. [Royal Military College of Canada, Dept. of Chemistry and Chemical Engineering, Kingston, Ontario (Canada)

    2002-08-01

    The coverage of the activities within the nuclear science and engineering programmes at RMC reveals the dynamism of the College which is still growing at a fast rate. Being the only completely bilingual university in Canada and a true national institution gathering students and staff from all parts of the country. RMC continues in its mission to support the Canadian Forces, the Department of National Defence, the people of Canada and Canadian Industry that includes the nuclear sector. It is in this spirit that the staff has been actively involved with organizations such as the Canadian Nuclear Society and the Canadian Nuclear Association, having hosted four of the Student conferences and three major topical conferences of the CNS.

  10. Radiation effects on ion-exchange resins. Part II. Gamma irradiation of Dowex 1

    International Nuclear Information System (INIS)

    Kazanjian, A.R.; Horrell, D.R.

    1975-01-01

    The effects were determined of gamma radiation on the anion exchange resin, Dowex 1. Part I on Dowex 50W was reported May 10, 1974. The exchange capacity (both strong and weak base), moisture content, radiolysis products, and physical deterioration of the resin were analyzed after irradiation with doses up to 6.9 x 10 8 rads. The resin capacity decreased approximately 50 percent after a radiation dose of 4 x 10 8 rads. Resin irradiated, when air dried in the nitrate form, showed more stability than resin irradiated in 7N nitric acid (HNO 3 ), which in turn showed more stability than resin irradiated when air dried in the chloride form. Radiation decreased the strong base capacity to a greater extent than the total capacity. The result indicates that some of the quarternary ammonium groups were transformed to secondary and tertiary amine groups that have weak base ion-exchange capability. (U.S.)

  11. Lead-acid batteries in micro-hybrid applications. Part II. Test proposal

    Energy Technology Data Exchange (ETDEWEB)

    Schaeck, S.; Stoermer, A.O. [BMW Group, 80788 Muenchen (Germany); Albers, J. [Johnson Controls Power Solutions EMEA, 30419 Hannover (Germany); Weirather-Koestner, D. [ZSW Ulm, 89081 Ulm (Germany); Kabza, H. [Universitaet Ulm, Institut fuer Energiewandlung und -speicherung, 89081 Ulm (Germany)

    2011-02-01

    In the first part of this work selected key parameters for applying lead-acid (LA) batteries in micro-hybrid power systems (MHPS) were investigated. Main results are integrated in an accelerated, comprehensive test proposal presented here. The test proposal aims at a realistic representation of the pSoC operation regime, which is described in Refs. The test is designed to be sensitive with respect to dynamic charge acceptance (DCA) at partially discharged state (critical for regenerative braking) and the internal resistance at high-rate discharge (critical for idling stop applications). First results are presented for up-to-date valve-regulated LA batteries with absorbent glass mat (AGM) separators. The batteries are close to the limits of the first proposal of pass/fail-criteria. Also flooded batteries were tested; the first out of ten units failed already. (author)

  12. Managing Returnable Containers Logistics - A Case Study Part II - Improving Visibility through Using Automatic Identification Technologies

    Directory of Open Access Journals (Sweden)

    Gretchen Meiser

    2011-05-01

    Full Text Available This case study is the result of a project conducted on behalf of a company that uses its own returnable containers to transport purchased parts from suppliers. The objective of this project was to develop a proposal to enable the company to more effectively track and manage its returnable containers. The research activities in support of this project included (1 the analysis and documentation of the physical flow and the information flow associated with the containers and (2 the investigation of new technologies to improve the automatic identification and tracking of containers. This paper explains the automatic identification technologies and important criteria for selection. A companion paper details the flow of information and containers within the logistics chain, and it identifies areas for improving the management of the containers.

  13. Evaluation of pump pulsation in respirable size-selective sampling: part II. Changes in sampling efficiency.

    Science.gov (United States)

    Lee, Eun Gyung; Lee, Taekhee; Kim, Seung Won; Lee, Larry; Flemmer, Michael M; Harper, Martin

    2014-01-01

    This second, and concluding, part of this study evaluated changes in sampling efficiency of respirable size-selective samplers due to air pulsations generated by the selected personal sampling pumps characterized in Part I (Lee E, Lee L, Möhlmann C et al. Evaluation of pump pulsation in respirable size-selective sampling: Part I. Pulsation measurements. Ann Occup Hyg 2013). Nine particle sizes of monodisperse ammonium fluorescein (from 1 to 9 μm mass median aerodynamic diameter) were generated individually by a vibrating orifice aerosol generator from dilute solutions of fluorescein in aqueous ammonia and then injected into an environmental chamber. To collect these particles, 10-mm nylon cyclones, also known as Dorr-Oliver (DO) cyclones, were used with five medium volumetric flow rate pumps. Those were the Apex IS, HFS513, GilAir5, Elite5, and Basic5 pumps, which were found in Part I to generate pulsations of 5% (the lowest), 25%, 30%, 56%, and 70% (the highest), respectively. GK2.69 cyclones were used with the Legacy [pump pulsation (PP) = 15%] and Elite12 (PP = 41%) pumps for collection at high flows. The DO cyclone was also used to evaluate changes in sampling efficiency due to pulse shape. The HFS513 pump, which generates a more complex pulse shape, was compared to a single sine wave fluctuation generated by a piston. The luminescent intensity of the fluorescein extracted from each sample was measured with a luminescence spectrometer. Sampling efficiencies were obtained by dividing the intensity of the fluorescein extracted from the filter placed in a cyclone with the intensity obtained from the filter used with a sharp-edged reference sampler. Then, sampling efficiency curves were generated using a sigmoid function with three parameters and each sampling efficiency curve was compared to that of the reference cyclone by constructing bias maps. In general, no change in sampling efficiency (bias under ±10%) was observed until pulsations exceeded 25% for the

  14. An Update on the Hazards and Risks of Forensic Anthropology, Part II: Field and Laboratory Considerations.

    Science.gov (United States)

    Roberts, Lindsey G; Dabbs, Gretchen R; Spencer, Jessica R

    2016-01-01

    This paper focuses on potential hazards and risks to forensic anthropologists while working in the field and laboratory in North America. Much has changed since Galloway and Snodgrass published their seminal article addressing these issues. The increased number of forensic practitioners combined with new information about potential hazards calls for an updated review of these pathogens and chemicals. Discussion of pathogen hazards (Brucella, Borrelia burgdorferi, Yersinia pestis, Clostridium tetani and West Nile virus) includes important history, exposure routes, environmental survivability, early symptoms, treatments with corresponding morbidity and mortality rates, and decontamination measures. Additionally, data pertaining to the use of formaldehyde in the laboratory environment have resulted in updated safety regulations, and these are highlighted. These data should inform field and laboratory protocols. The hazards of working directly with human remains are discussed in a companion article, "An Update on the Hazards and Risks of Forensic Anthropology, Part I: Human Remains." © 2015 American Academy of Forensic Sciences.

  15. The Systemic Products as a Source of Competitive Advantage on Healthcare Sector Example. Part II

    Directory of Open Access Journals (Sweden)

    Izabela SZTANGRET

    2015-12-01

    Full Text Available In the healthcare sector, different healthcare providers, such as home care, primary care, pharmacies and hospital clinics but also a financial institution, collaborate in order to increase values for patients, such as better health state, more complex services, high quality of services, and increased feeling of safety. By creating a value, flexible networks health care providers and additional actors create value through collaboration. The purpose of this article is to identify the specific character of systemic healthcare product, created in synergy relations of medical enntities in the area of new way of meeting customers’ needs. Critical analysis of literature in the field of studied category is conducted in the article; furthermore qualitative method of empirical studies (case study and quantitative (online questionnaire is applied for practical illustration of described processes and phenomena. The article is a second part of the stud.

  16. FIB/SEM study of AA2024 corrosion under a seawater drop, part II

    International Nuclear Information System (INIS)

    King, Peter C.; Cole, Ivan S.; Corrigan, Penny A.; Hughes, Anthony E.; Muster, Tim H.; Thomas, Sebastian

    2012-01-01

    Highlights: ► Dealloying has a directional nature, exhibits banding. ► Oxidation state of copper in sponge remnants found to be variable. ► Dissolution and breakdown of copper sponge structure observed. ► Crystalline defects imaged in dealloyed S-phase. - Abstract: The dissolution of S-phase clusters in aluminium alloy 2024 (AA2024) exposed to a 0.5 μl seawater droplet is presented. Foils for transmission electron microscopy (TEM) were made from local attack sites using a focussed ion beam/scanning electron microscope (FIB/SEM). The sections showed that clusters of S-phase particles underwent dealloying. The resulting copper sponge morphology, banding, preferred orientation and crystal defect structure as a result of plastic deformation have been characterised. With build-up of amorphous corrosion product, physical and electrical isolation of parts of the clusters developed, with the result of copper dissolution from the S-phase remnants.

  17. STEVENS–JOHNSON SYNDROME — TOXIC EPIDERMAL NECTROLYSIS IN CHILDREN. PART II. SYSTEM, LOCAL TREATMENT

    Directory of Open Access Journals (Sweden)

    V.F. Zhernosek

    2011-01-01

    Full Text Available The second part of the article concerning Stevens–Johnson syndrome — toxic epidermal necrolysis (SJS–TEN is devoted to the treatment of this disease. The modern approaches to the use of systemic agents — antibacterial, antiviral, analgesics and sedatives, and anticoagulants are discussed in detail. Regulations of the drugs use depending on the patient state and the etiology of SJS–TEN are marked out. The basic principles of the fluid therapy for rehydration and dehydration prevention are shown in the article. Particular attention is paid to the local therapy — treatment of mucous membranes and skin lesions.Key words: Stevens-Johnson syndrome, toxic epidermal necrolysis, children, antibiotic therapy, topical treatment.

  18. The nuclear engineering programmes at the Royal Military College of Canada. Part II

    International Nuclear Information System (INIS)

    Bonin, H.W.

    2002-01-01

    The coverage of the activities within the nuclear science and engineering programmes at RMC reveals the dynamism of the College which is still growing at a fast rate. Being the only completely bilingual university in Canada and a true national institution gathering students and staff from all parts of the country. RMC continues in its mission to support the Canadian Forces, the Department of National Defence, the people of Canada and Canadian Industry that includes the nuclear sector. It is in this spirit that the staff has been actively involved with organizations such as the Canadian Nuclear Society and the Canadian Nuclear Association, having hosted four of the Student conferences and three major topical conferences of the CNS

  19. How Clean Are Hotel Rooms? Part II: Examining the Concept of Cleanliness Standards.

    Science.gov (United States)

    Almanza, Barbara A; Kirsch, Katie; Kline, Sheryl Fried; Sirsat, Sujata; Stroia, Olivia; Choi, Jin Kyung; Neal, Jay

    2015-01-01

    Hotel room cleanliness is based on observation and not on microbial assessment even though recent reports suggest that infections may be acquired while staying in hotel rooms. Exploratory research in the first part of the authors' study was conducted to determine if contamination of hotel rooms occurs and whether visual assessments are accurate indicators of hotel room cleanliness. Data suggested the presence of microbial contamination that was not reflective of visual assessments. Unfortunately, no standards exist for interpreting microbiological data and other indicators of cleanliness in hotel rooms. The purpose of the second half of the authors' study was to examine cleanliness standards in other industries to see if they might suggest standards in hotels. Results of the authors' study indicate that standards from other related industries do not provide analogous criteria, but do provide suggestions for further research.

  20. Exhaust Gas Temperature Measurements in Diagnostics of Turbocharged Marine Internal Combustion Engines Part II Dynamic Measurements

    Directory of Open Access Journals (Sweden)

    Korczewski Zbigniew

    2016-01-01

    Full Text Available The second part of the article describes the technology of marine engine diagnostics making use of dynamic measurements of the exhaust gas temperature. Little-known achievements of Prof. S. Rutkowski of the Naval College in Gdynia (now: Polish Naval Academy in this area are presented. A novel approach is proposed which consists in the use of the measured exhaust gas temperature dynamics for qualitative and quantitative assessment of the enthalpy flux of successive pressure pulses of the exhaust gas supplying the marine engine turbocompressor. General design assumptions are presented for the measuring and diagnostic system which makes use of a sheathed thermocouple installed in the engine exhaust gas manifold. The corrected thermal inertia of the thermocouple enables to reproduce a real time-history of exhaust gas temperature changes.