WorldWideScience

Sample records for batteries electric

  1. Batteries for Electric Vehicles

    Science.gov (United States)

    Conover, R. A.

    1985-01-01

    Report summarizes results of test on "near-term" electrochemical batteries - (batteries approaching commercial production). Nickel/iron, nickel/zinc, and advanced lead/acid batteries included in tests and compared with conventional lead/acid batteries. Batteries operated in electric vehicles at constant speed and repetitive schedule of accerlerating, coasting, and braking.

  2. Electric Vehicle Battery Challenge

    Science.gov (United States)

    Roman, Harry T.

    2014-01-01

    A serious drawback to electric vehicles [batteries only] is the idle time needed to recharge their batteries. In this challenge, students can develop ideas and concepts for battery change-out at automotive service stations. Such a capability would extend the range of electric vehicles.

  3. Electric-vehicle batteries

    Science.gov (United States)

    Oman, Henry; Gross, Sid

    1995-02-01

    Electric vehicles that can't reach trolley wires need batteries. In the early 1900's electric cars disappeared when owners found that replacing the car's worn-out lead-acid battery costs more than a new gasoline-powered car. Most of today's electric cars are still propelled by lead-acid batteries. General Motors in their prototype Impact, for example, used starting-lighting-ignition batteries, which deliver lots of power for demonstrations, but have a life of less than 100 deep discharges. Now promising alternative technology has challenged the world-wide lead miners, refiners, and battery makers into forming a consortium that sponsors research into making better lead-acid batteries. Horizon's new bipolar battery delivered 50 watt-hours per kg (Wh/kg), compared with 20 for ordinary transport-vehicle batteries. The alternatives are delivering from 80 Wh/kg (nickel-metal hydride) up to 200 Wh/kg (zinc-bromine). A Fiat Panda traveled 260 km on a single charge of its zinc-bromine battery. A German 3.5-ton postal truck traveled 300 km with a single charge in its 650-kg (146 Wh/kg) zinc-air battery. Its top speed was 110 km per hour.

  4. Battery charging control methods, electric vehicle charging methods, battery charging apparatuses and rechargeable battery systems

    Science.gov (United States)

    Tuffner, Francis K.; Kintner-Meyer, Michael C. W.; Hammerstrom, Donald J.; Pratt, Richard M.

    2012-05-22

    Battery charging control methods, electric vehicle charging methods, battery charging apparatuses and rechargeable battery systems. According to one aspect, a battery charging control method includes accessing information regarding a presence of at least one of a surplus and a deficiency of electrical energy upon an electrical power distribution system at a plurality of different moments in time, and using the information, controlling an adjustment of an amount of the electrical energy provided from the electrical power distribution system to a rechargeable battery to charge the rechargeable battery.

  5. Battery Health Management System for Electric UAVs

    Data.gov (United States)

    National Aeronautics and Space Administration — In summary, this paper lays out a novel battery health management technique for application onboard an electric UAV. This technique is also applicable to other...

  6. Predicting Battery Life for Electric UAVs

    Data.gov (United States)

    National Aeronautics and Space Administration — This paper presents a novel battery health management technology for the new generation of electric unmanned aerial vehicles powered by long-life, high-density,...

  7. Repurposing of Batteries from Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Viswanathan, Vilayanur V.; Kintner-Meyer, Michael CW

    2015-06-11

    Energy storage for stationary use is gaining traction both at the grid scale and distributed level. As renewable energy generation increases, energy storage is needed to compensate for the volatility of renewable over various time scales. This requires energy storage that is tailored for various energy to power (E/P) ratios. Other applications for energy storage include peak shaving, time shifting, load leveling, VAR control, frequency regulation, spinning reserves and other ancillary applications. While the need for energy storage for stationary applications is obvious, the regulations that determine the economic value of adding storage are at various stages of development. This has created a reluctance on the part of energy storage manufacturers to develop a suite of storage systems that can address the myriad of applications associated with stationary applications. Deployment of battery energy storage systems in the transportation sector is ahead of the curve with respect to the stationary space. Batteries, along with battery management systems (BMS) have been deployed for hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs) and electric vehicles (EVs). HEVs have now been deployed for 12 years, while PHEVs for 8 and EVs for 4 years. Some of the batteries are approaching end of life within the vehicle, and are ready to be taken off for recycling and disposal. Performance within a vehicle is non-negotiable in terms of miles traveled per charge, resulting in the batteries retaining a significant portion of their life. For stationary applications, the remaining energy and power of the battery can still be used by grouping together a few of these batteries. This enables getting the most of these batteries, while ensuring that performance is not compromised in either the automotive or stationary applications. This work summarizes the opportunities for such re-purposing of automotive batteries, along with the advantages and limitations

  8. Gelled-electrolyte batteries for electric vehicles

    Science.gov (United States)

    Tuphorn, Hans

    Increasing problems of air pollution have pushed activities of electric vehicle projects worldwide and in spite of projects for developing new battery systems for high energy densities, today lead/acid batteries are almost the single system, ready for technical usage in this application. Valve-regulated lead/acid batteries with gelled electrolyte have the advantage that no maintenance is required and because the gel system does not cause problems with electrolyte stratification, no additional appliances for central filling or acid addition are required, which makes the system simple. Those batteries with high density active masses indicate high endurance results and field tests with 40 VW-CityStromers, equipped with 96 V/160 A h gel batteries with thermal management show good results during four years. In addition, gelled lead/acid batteries possess superior high rate performance compared with conventional lead/acid batteries, which guarantees good acceleration results of the car and which makes the system recommendable for application in electric vehicles.

  9. Bipolar lead-acid battery for hybrid electric vehicles

    NARCIS (Netherlands)

    Schmal, D.; Saakes, M.; Veen, W.R. ter; Raadschelders, J.W.; Have, P.T.J.H. ten

    2000-01-01

    In hybrid electric vehicles (HEV) the requirements on batteries are very different from those for battery electric vehicles (BEV). A high power (bipolar) lead-acid battery could be a good alternative for other types of batteries under development for this application. It is potentially cheap and the

  10. Battery module design for electric racecar

    OpenAIRE

    Tenas Garcia, Josep

    2011-01-01

    BME Formula Racing Team is working at Technical University of Budapest. The main purpose is to design and build internal combustion engine and electric motor driven racecars and take part in Formula Student Competition. It is an international constructor competition series in which teams of universities and college students are competing in design in, building and running a racecar. As a new project of the FRT, a battery-fed electric racecar is being built which is driven by two PMSM hub m...

  11. Battery management system for electric racing cars

    OpenAIRE

    Araújo, Joaquim Alexandre da Silva

    2013-01-01

    With the introduction of the electrics cars into the market new technologies regarding the battery are being developed and new problems to be solved, one of them the battery management system because each type of cell requires a specific way of handling. This research is done using the active research method to find out the actual problem on this subject and features a BMS should have, understand how they work and how to develop them applied to the purpose on this work. Once the features the ...

  12. Advanced state prediction of lithium-ion traction batteries in hybrid and battery electric vehicle applications

    Energy Technology Data Exchange (ETDEWEB)

    Jadidi, Yasser

    2011-07-01

    Automotive power trains with high energy efficiencies - particularly to be found in battery and hybrid electric vehicles - find increasing attention in the focus of reduction of exhaust emissions and increase of mileage. The underlying concept, the electrification of the power train, is subject to the traction battery and its battery management system since the capability of the battery permits and restricts electric propulsion. Consequently, the overall vehicle efficiency and in particular the operation strategy performance strongly depends on the quality of information about the battery. Besides battery technology, the key challenges are given by both the accurate prediction of battery behaviour and the electrochemical battery degradation that leads to power and capacity fade of the traction battery. This book provides the methodology for development of a battery state monitoring and prediction algorithm for application in a battery management system that accounts for the effects of electrochemical degradation. (orig.)

  13. Lithium batteries for electric road vehicle applications

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Bo; Hallgren, B.; Johansson, Arne; Selaanger, P. [Catella Generics, Kista (Sweden)

    1995-12-31

    Lithium is one of the most promising negative electrode materials to be used for the manufacturing of batteries. It is the most electronegative material in the table of standard potentials and its low weight will facilitate a high gravimetric coulombic density. Theoretically, as high values as 6 kWh/kg could be reached for lithium based batteries. The aim of this study has been to make an inventory of what is internationally known about lithium batteries suitable for electric vehicle applications. It is representative for the development status by the summer of 1995. Both high and ambient temperature lithium batteries are described in the study even if the analysis is concentrated on the latter. Ambient temperature systems has gathered the major interest, especially from manufacturers in the `3Cs` market segment (Consumer electronics, Communications and Computers). There is no doubt, a bright future for lithium rechargeable batteries. Depending on the ambition of a national research programme, one can await the ongoing development of batteries for the 3Cs market segment or take the lead in a near-term or advanced system R and D for EV batteries. In the zero ambition EV battery programme, we recommend allocation of funds to follow the development within the 3Cs sector. The corresponding funding level is 1-2 MSEK/year granted to a stable receiver. In a low ambition EV programme, we recommend to keep a few groups active in the front-line of specific research areas. The purpose is to keep a link for communication open to the surrounding battery world. The cost level is 4-6 MSEK per year continually. In a high ambition programme we recommend the merging of Swedish resources with international EV battery R and D programmes, e.g. the EUCAR project. The research team engaged should be able to contribute to the progress of the overall project. The cost for the high ambition programme is estimated at the level 15-20 MSEK per year continually. 47 refs, 17 figs, 16 tabs

  14. Recycling of Advanced Batteries for Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    JUNGST,RUDOLPH G.

    1999-10-06

    The pace of development and fielding of electric vehicles is briefly described and the principal advanced battery chemistries expected to be used in the EV application are identified as Ni/MH in the near term and Li-ion/Li-polymer in the intermediate to long term. The status of recycling process development is reviewed for each of the two chemistries and future research needs are discussed.

  15. Bipolar lead-acid batteries for electrical actuation applications

    Science.gov (United States)

    Pierce, Douglas C.; Gentry, William O.; Hall, David

    1994-01-01

    This document presents in viewgraph format information on bipolar battery development at Johnson Controls, Incorporated. The organization structure, goals, progress to date, future plans, and battery parameters and electrical properties are given.

  16. Lightweight lead acid batteries for hybrid electric vehicle applications

    OpenAIRE

    Wallis, Lauren

    2015-01-01

    This report presents architectures, designs and chemistries for novel static soluble lead acid batteries, with the objective of producing a lightweight lead acid battery for improved specific energy. The demands for lightweight lead-acid batteries come from an expanding hybrid electric vehicle market demanding improved battery specific energy. There are several avenues for improving battery specific energy; the main two are improved active material utilisation efficiency and grid weight reduc...

  17. Battery model for electrical power system energy balance

    Science.gov (United States)

    Hafen, D. P.

    1983-01-01

    A model to simulate nickel-cadmium battery performance and response in a spacecraft electrical power system energy balance calculation was developed. The voltage of the battery is given as a function of temperature, operating depth-of-charge (DOD), and battery state-of-charge. Also accounted for is charge inefficiency. A battery is modeled by analysis of the results of a multiparameter battery cycling test at various temperatures and DOD's.

  18. Optimized batteries for cars with dual electrical architecture

    Science.gov (United States)

    Douady, J. P.; Pascon, C.; Dugast, A.; Fossati, G.

    During recent years, the increase in car electrical equipment has led to many problems with traditional starter batteries (such as cranking failure due to flat batteries, battery cycling etc.). The main causes of these problems are the double function of the automotive battery (starter and service functions) and the difficulties in designing batteries well adapted to these two functions. In order to solve these problems a new concept — the dual-concept — has been developed with two separate batteries: one battery is dedicated to the starter function and the other is dedicated to the service function. Only one alternator charges the two batteries with a separation device between the two electrical circuits. The starter battery is located in the engine compartment while the service battery is located at the rear of the car. From the analysis of new requirements, battery designs have been optimized regarding the two types of functions: (i) a small battery with high specific power for the starting function; for this function a flooded battery with lead-calcium alloy grids and thin plates is proposed; (ii) for the service function, modified sealed gas-recombinant batteries with cycling and deep-discharge ability have been developed. The various advantages of the dual-concept are studied in terms of starting reliability, battery weight, and voltage supply. The operating conditions of the system and several dual electrical architectures have also been studied in the laboratory and the car. The feasibility of the concept is proved.

  19. The requirements for batteries for electric vehicles

    Science.gov (United States)

    Schwartz, H. J.

    1976-01-01

    The paper reassesses the role of electric vehicles in the modern transportation system and their potential impact on oil consumption. Three major factors determining the size of this impact are discussed: the market potential, the date of introduction, and the rate of consumer acceptance. The strategy of selecting the battery type for an urban car to introduce in coming years is analyzed. The results of the analysis suggest that the research and development emphasis should be placed on near- and mid-term battery technology. From the standpoint of maximizing both the cumulative impact and the benefits derived in the year 2000, however, a strategy of early introduction of near-term and mid-term cars followed by the far-term vehicles seems to produce the optimum result.

  20. Battery Management System Design and Implementation in Electric Raceabout - Electric Sportscar

    OpenAIRE

    Sainio, Joonas

    2013-01-01

    The purpose of this Bachelor´s study was to design and implement a new user-configurable battery management system into Electric Raceabout – electric sports car. This new improved system design would replace the old battery management system in the vehicle. The thesis begins by characterizing a professional battery management system and representing the benefits of the new system. Following the objectives of professional battery management systems, the new battery management system was de...

  1. Performance of the Lester battery charger in electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Vivian, H.C.; Bryant, J.A.

    1984-04-15

    Tests were performed on an improved battery charger manufactured by Lester Electrical of Nebraska, Inc. This charger was installed in a South Coast Technology Rabbit No. 4, which was equipped with lead-acid batteries produced by ESB Company. The primary purpose of the testing was to develop test methodologies for battery charger evaluation. To this end tests were developed to characterize the charger in terms of its charge algorithm and to assess the effects of battery initial state of charge and temperature on charger and battery efficiency. Tests showed this charger to be a considerable improvement in the state of the art for electric vehicle chargers.

  2. Battery prices and capacity sensitivity: Electric drive vehicles

    DEFF Research Database (Denmark)

    Juul, Nina

    2012-01-01

    the next decade or two. These vehicles can provide some of the flexibility needed in the power system, in terms of both flexible demand and electricity storage. However, what are the batteries worth to the power system? And does the value depend on battery capacity? This article presents an analysis...... of the integrated power and transport system, focusing on the sensitivity of the power system configuration according to battery capacity and price of the electric drive vehicle. The value of different battery capacities is estimated, given that the batteries are used for both driving and storage. Likewise......, the prices at which the electric drive vehicles become of interest to the power system are found. Smart charge, including the opportunity to discharge (vehicle-to-grid) is used in all scenarios. Analyses show that the marginal benefits decrease the larger the battery. For very high battery prices, large...

  3. Performance of the Lester battery charger in electric vehicles

    Science.gov (United States)

    Vivian, H. C.; Bryant, J. A.

    1984-01-01

    Tests are performed on an improved battery charger. The primary purpose of the testing is to develop test methodologies for battery charger evaluation. Tests are developed to characterize the charger in terms of its charge algorithm and to assess the effects of battery initial state of charge and temperature on charger and battery efficiency. Tests show this charger to be a considerable improvement in the state of the art for electric vehicle chargers.

  4. Advanced Battery Diagnosis for Electric Vehicles

    OpenAIRE

    Lamichhane, Chudamani

    2008-01-01

    Summary Literatures on battery technologies and diagnosis of its parameters were studied. The innovative battery technologies from basic knowledge to world standard testing procedures were analysed and discussed in the report. The established battery test station and flowchart was followed during the battery test preparation and testing. In order to understand and verify the battery performance, the well established test procedures developed by USABC (United States Advanced Battery Consorti...

  5. The Electric Car Battery. Sustainability in the Supply Chain

    Energy Technology Data Exchange (ETDEWEB)

    Steinweg, T.

    2011-03-15

    This report aims to provide an initial overview of the supply chain of electric car batteries, and to answer the following research question: What effect does the growing demand for electric vehicles have on the social and environmental conditions throughout the electric car battery supply chain? This report will combine various methodologies to be able to create an overall picture of the electric car battery supply chain, and is targeted towards companies, public servants, opinion makers and the general public interested in the electric car.

  6. On-line battery identification for electric driving range prediction

    NARCIS (Netherlands)

    Kessels, J.T.B.A.; Rosca, B.; Bergveld, H.J.; Bosch, P.P.J. van den

    2011-01-01

    Hybrid and electric vehicles require accurate knowledge of the battery to make an educated guess about the expected electric driving range. Range prediction is complicated by the fact that batteries are subject to external influences and aging. Also the future driving behavior is often unknown. This

  7. Review on Electric Vehicle, Battery Charger, Charging Station and Standards

    OpenAIRE

    Afida Ayob; Wan Mohd Faizal Wan Mahmood; Azah Mohamed Mohd Zamri Che Wanik; MohdFadzil Mohd Siam; Saharuddin Sulaiman; Abu Hanifah Azit; Mohamed Azrin Mohamed Ali

    2014-01-01

    Electric vehicles are a new and upcoming technology in the transportation and power sector that have many benefits in terms of economic and environmental. This study presents a comprehensive review and evaluation of various types of electric vehicles and its associated equipment in particular battery charger and charging station. A comparison is made on the commercial and prototype electric vehicles in terms of electric range, battery size, charger power and charging time. The various types o...

  8. Optimization of batteries for plug-in hybrid electric vehicles

    Science.gov (United States)

    English, Jeffrey Robb

    This thesis presents a method to quickly determine the optimal battery for an electric vehicle given a set of vehicle characteristics and desired performance metrics. The model is based on four independent design variables: cell count, cell capacity, state-of-charge window, and battery chemistry. Performance is measured in seven categories: cost, all-electric range, maximum speed, acceleration, battery lifetime, lifetime greenhouse gas emissions, and charging time. The performance of each battery is weighted according to a user-defined objective function to determine its overall fitness. The model is informed by a series of battery tests performed on scaled-down battery samples. Seven battery chemistries were tested for capacity at different discharge rates, maximum output power at different charge levels, and performance in a real-world automotive duty cycle. The results of these tests enable a prediction of the performance of the battery in an automobile. Testing was performed at both room temperature and low temperature to investigate the effects of battery temperature on operation. The testing highlighted differences in behavior between lithium, nickel, and lead based batteries. Battery performance decreased with temperature across all samples with the largest effect on nickel-based chemistries. Output power also decreased with lead acid batteries being the least affected by temperature. Lithium-ion batteries were found to be highly efficient (>95%) under a vehicular duty cycle; nickel and lead batteries have greater losses. Low temperatures hindered battery performance and resulted in accelerated failure in several samples. Lead acid, lead tin, and lithium nickel alloy batteries were unable to complete the low temperature testing regime without losing significant capacity and power capability. This is a concern for their applicability in electric vehicles intended for cold climates which have to maintain battery temperature during long periods of inactivity

  9. Foothill Transit Battery Electric Bus Demonstration Results

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Prohaska, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kelly, Kenneth [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-01-27

    Foothill Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL) to evaluate its fleet of Proterra battery electric buses (BEBs) in revenue service. The focus of this evaluation is to compare performance of the BEBs to that of conventional technology and to track progress over time toward meeting performance targets. This project has also provided an opportunity for DOE to conduct a detailed evaluation of the BEBs and charging infrastructure. This report provides data on the buses from April 2014 through July 2015. Data are provided on a selection of compressed natural gas buses as a baseline comparison.

  10. An averaging battery model for a lead-acid battery operating in an electric car

    Science.gov (United States)

    Bozek, J. M.

    1979-01-01

    A battery model is developed based on time averaging the current or power, and is shown to be an effective means of predicting the performance of a lead acid battery. The effectiveness of this battery model was tested on battery discharge profiles expected during the operation of an electric vehicle following the various SAE J227a driving schedules. The averaging model predicts the performance of a battery that is periodically charged (regenerated) if the regeneration energy is assumed to be converted to retrievable electrochemical energy on a one-to-one basis.

  11. Batteries for Electric Vehicles and Hybrid Electric Vehicles - State of the art - Perspectives

    OpenAIRE

    PELISSIER, Serge

    2012-01-01

    Batteries are often considered to be the main obstacle in the diffusion of Hybrid Electric and Electric Vehicles. Indeed autonomy and lifetime of the vehicle are key points that depend directly on the batteries. Many recent developments have deeply modified their characteristics. Lithium batteries are often considered as the solution for energy storage in automotive applications but actually there is a large variety in the lithium batteries family. Even if published results periodically annou...

  12. Review on Electric Vehicle, Battery Charger, Charging Station and Standards

    Directory of Open Access Journals (Sweden)

    Afida Ayob

    2014-01-01

    Full Text Available Electric vehicles are a new and upcoming technology in the transportation and power sector that have many benefits in terms of economic and environmental. This study presents a comprehensive review and evaluation of various types of electric vehicles and its associated equipment in particular battery charger and charging station. A comparison is made on the commercial and prototype electric vehicles in terms of electric range, battery size, charger power and charging time. The various types of charging stations and standards used for charging electric vehicles have been outlined and the impact of electric vehicle charging on utility distribution system is also discussed.

  13. Battery Management Systems in Electric and Hybrid Vehicles

    Directory of Open Access Journals (Sweden)

    Michael Pecht

    2011-10-01

    Full Text Available The battery management system (BMS is a critical component of electric and hybrid electric vehicles. The purpose of the BMS is to guarantee safe and reliable battery operation. To maintain the safety and reliability of the battery, state monitoring and evaluation, charge control, and cell balancing are functionalities that have been implemented in BMS. As an electrochemical product, a battery acts differently under different operational and environmental conditions. The uncertainty of a battery’s performance poses a challenge to the implementation of these functions. This paper addresses concerns for current BMSs. State evaluation of a battery, including state of charge, state of health, and state of life, is a critical task for a BMS. Through reviewing the latest methodologies for the state evaluation of batteries, the future challenges for BMSs are presented and possible solutions are proposed as well.

  14. A Cost analysis of electric vehicle batteries second life businesses

    OpenAIRE

    Canals Casals, Lluc; Amante García, Beatriz; González Benítez, María Margarita

    2016-01-01

    In the following years thousands of electric cars are expected to be sold. Knowing that these batteries are not useful anymore for traction services after they have lost a 20% of its capacity, there will be thousands of batteries able for re-use. The re-use represents a considerable environment improvement compared to the immediate recycling. According to battery recycling enterprises, not even half of them are collected back after their use but car manufacturers should ensure that their elec...

  15. 2010 Honda Civic Hybrid UltraBattery Conversion 5577 - Hybrid Electric Vehicle Battery Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Tyler Gray; Matthew Shirk; Jeffrey Wishart

    2013-07-01

    The U.S. Department of Energy Advanced Vehicle Testing Activity Program consists of vehicle, battery, and infrastructure testing on advanced technology related to transportation. The activity includes tests on hybrid electric vehicles (HEVs), including testing the HEV batteries when both the vehicles and batteries are new and at the conclusion of on-road fleet testing. This report documents battery testing performed for the 2010 Honda Civic HEV UltraBattery Conversion (VIN JHMFA3F24AS005577). Battery testing was performed by the Electric Transportation Engineering Corporation dba ECOtality North America. The Idaho National Laboratory and ECOtality North America collaborate on the AVTA for the Vehicle Technologies Program of the DOE.

  16. Battery diagnosis and battery monitoring in hybrid electric vehicles; Batteriediagnostik und Batteriemonitoring in Hybridfahrzeugen

    Energy Technology Data Exchange (ETDEWEB)

    Sanders, T.; Kowal, J.; Waag, W.; Gerschler, J.B.; Sauer, D.U. [RWTH Aachen (DE). Inst. fuer Stromrichtertechnik und Elektrische Antriebe (ISEA)

    2007-07-01

    Even in conventional passenger cars the load on the batteries is at its limit due to the increasing number of electrical loads. It is therefore of special importance to know the status and the power capability of the battery at any time. To fulfil these requirements it is necessary that the battery diagnostics has a precise current measurement available in addition to the voltage and temperature measurements. Battery diagnosis is most successful of different algorithms are combined and errors from the measurements and the algorithms are taken actively into account. The general structure of battery diagnosis algorithms can be used for lead-acid, lithium-ion and NiMH batteries. However, the complexity is highest for lead-acid batteries. (orig.)

  17. An Electric Bus with a Battery Exchange System

    Directory of Open Access Journals (Sweden)

    Jeongyong Kim

    2015-07-01

    Full Text Available As part of the ongoing effort to be independent of petroleum resources and to be free from pollutant emission issues, various electric vehicles have been developed and tested through their integration with real world systems. In the current paper, yet another application specific EV for public transportation, an electric bus, is introduced and explained with results from the pilot test program which was carried out under real traffic conditions. The main feature of the current system is a battery exchanging mechanism mounted on the roof of the bus. The current configuration certainly requires an externally fabricated battery exchanging robot system that would complement the electric bus for a fully automated battery exchanging process. The major advantage of the current system is the quick re-charging of the electric energy through the physical battery exchange and the possible utilization of the battery exchange station as a mini scale energy storage system for grid system peak power shaving. With the total system solution approach for the public transportation system, it is fully expected to create outstanding business opportunities in number of areas such as battery suppliers, battery exchanging station management, battery leasing and many more.

  18. Recycling readiness of advanced batteries for electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jungst, R.G.

    1997-09-01

    Maximizing the reclamation/recycle of electric-vehicle (EV) batteries is considered to be essential for the successful commercialization of this technology. Since the early 1990s, the US Department of Energy has sponsored the ad hoc advanced battery readiness working group to review this and other possible barriers to the widespread use of EVs, such as battery shipping and in-vehicle safety. Regulation is currently the main force for growth in EV numbers and projections for the states that have zero-emission vehicle (ZEV) programs indicate about 200,000 of these vehicles would be offered to the public in 2003 to meet those requirements. The ad hoc Advanced Battery Readiness Working Group has identified a matrix of battery technologies that could see use in EVs and has been tracking the state of readiness of recycling processes for each of them. Lead-acid, nickel/metal hydride, and lithium-ion are the three EV battery technologies proposed by the major automotive manufacturers affected by ZEV requirements. Recycling approaches for the two advanced battery systems on this list are partly defined, but could be modified to recover more value from end-of-life batteries. The processes being used or planned to treat these batteries are reviewed, as well as those being considered for other longer-term technologies in the battery recycling readiness matrix. Development efforts needed to prepare for recycling the batteries from a much larger EV population than exists today are identified.

  19. Modelling Thermal Effects of Battery Cells inside Electric Vehicle Battery Packs

    DEFF Research Database (Denmark)

    Khan, Mohammad Rezwan; Kær, Søren Knudsen

    -physical characteristics and their impact on the electrical state of battery cells(Khan, Mulder et al. 2013, Khan, Andreasen et al. 2014, Khan et al. 2014, Khan, Mulder et al. 2014, Khan, Nielsen et al. 2014). Based on this analysis, we derive strategies in achieving the goal, and then propose a battery thermal management...

  20. Electric Peugeot to have new nickel-iron batteries

    Science.gov (United States)

    1984-09-01

    Four articles, one from Austria and three from France, announce the introduction of a new electric automobile. The new car is a French made Peugeot. A feasible electric car is made possible by the development of a new nickel-iron battery. The new battery is smaller and lighter in weight. Specifications are given and discussed along with the working range and charge efficiency data.

  1. Developments in batteries and fuel cells for electric and hybrid electric vehicles

    International Nuclear Information System (INIS)

    Due to ever increasing threats of climate change, urban air pollution and costly and depleting oil and gas sources a lot of work is being done for the development of electric vehicles. Hybrid electric vehicles, plug-in hybrid electric vehicles and all electric vehicles are powered by batteries or by hydrogen and fuel cells are the main types of vehicles being developed. Main types of batteries which can be used for electric vehicles are lead-acid, Ni-Cd, Nickel-Metal-Hybrid ( NiMH) and Lithium-ion (Li-ion) batteries which are discussed and compared. Lithium ion battery is the mostly used battery. Developments in the lithium ion batteries are discussed and reviewed. Redox flow batteries are also potential candidates for electric vehicles and are described. Hybrid electric vehicles can reduce fuel consumption considerably and is a good midterm solution. Electric and hybrid electric vehicles are discussed. Electric vehicles are necessary to mitigate the effects of pollution and dependence on oil. For all the electric vehicles there are two options: batteries and fuel Cells. Batteries are useful for small vehicles and shorter distances but for vehicle range greater than 150 km fuel cells are superior to batteries in terms of cost, efficiency and durability even using natural gas and other fuels in addition to hydrogen. Ultimate solution for electric vehicles are hydrogen and fuel cells and this opinion is also shared by most of the automobile manufacturers. Developments in fuel cells and their applications for automobiles are described and reviewed. Comparisons have been done in the literature between batteries and fuel cells and are described. (author)

  2. Battery Test Manual For Plug-In Hybrid Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey R. Belt

    2010-09-01

    This battery test procedure manual was prepared for the United States Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Vehicle Technologies Program. It is based on technical targets established for energy storage development projects aimed at meeting system level DOE goals for Plug-in Hybrid Electric Vehicles (PHEV). The specific procedures defined in this manual support the performance and life characterization of advanced battery devices under development for PHEV’s. However, it does share some methods described in the previously published battery test manual for power-assist hybrid electric vehicles. Due to the complexity of some of the procedures and supporting analysis, a revision including some modifications and clarifications of these procedures is expected. As in previous battery and capacitor test manuals, this version of the manual defines testing methods for full-size battery systems, along with provisions for scaling these tests for modules, cells or other subscale level devices.

  3. Battery Test Manual For Plug-In Hybrid Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey R. Belt

    2010-12-01

    This battery test procedure manual was prepared for the United States Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Vehicle Technologies Program. It is based on technical targets established for energy storage development projects aimed at meeting system level DOE goals for Plug-in Hybrid Electric Vehicles (PHEV). The specific procedures defined in this manual support the performance and life characterization of advanced battery devices under development for PHEV’s. However, it does share some methods described in the previously published battery test manual for power-assist hybrid electric vehicles. Due to the complexity of some of the procedures and supporting analysis, a revision including some modifications and clarifications of these procedures is expected. As in previous battery and capacitor test manuals, this version of the manual defines testing methods for full-size battery systems, along with provisions for scaling these tests for modules, cells or other subscale level devices.

  4. 2011 Hyundai Sonata 4932 - Hybrid Electric Vehicle Battery Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Tyler Gray; Matthew Shirk; Jeffrey Wishart

    2013-07-01

    The U.S. Department of Energy Advanced Vehicle Testing Activity Program consists of vehicle, battery, and infrastructure testing on advanced technology related to transportation. The activity includes tests on hybrid electric vehicles (HEVs), including testing the HEV batteries when both the vehicles and batteries are new and at the conclusion of 160,000 miles of on-road fleet testing. This report documents battery testing performed for the 2011 Hyundai Sonata Hybrid HEV (VIN KMHEC4A43BA004932). Battery testing was performed by the Electric Transportation Engineering Corporation dba ECOtality North America. The Idaho National Laboratory and ECOtality North America collaborate on the AVTA for the Vehicle Technologies Program of the DOE.

  5. Smart battery charger for electric mobility in smart grids

    OpenAIRE

    Monteiro, Vítor Duarte Fernandes; João C. Ferreira; João L Afonso

    2012-01-01

    In this paper is presented the development of a smart batteries charger for Electric Vehicles (EVs) and Plug-in Hybrid Electric Vehicles (PHEVs), aiming their integration in Smart Grids. The batteries charging process is controlled by an appropriate control algorithm, aiming to preserve the batteries lifespan. The main features of the equipment are the mitigation of the power quality degradation and the bidirectional operation, as Grid-to-Vehicle (G2V) and as Vehicle-to-Grid (V2G). During the...

  6. Second Life for Electric Vehicle Batteries: Answering Questions on Battery Degradation and Value

    Energy Technology Data Exchange (ETDEWEB)

    Neubauer, J. S.; Wood, E.; Pesaran, A.

    2015-05-04

    Battery second use – putting used plug-in electric vehicle (PEV) batteries into secondary service following their automotive tenure – has been proposed as a means to decrease the cost of PEVs while providing low cost energy storage to other fields (e.g. electric utility markets). To understand the value of used automotive batteries, however, we must first answer several key questions related to National Renewable Energy Laboratory (NREL) has developed a methodology and the requisite tools to answer these questions, including NREL’s Battery Lifetime Simulation Tool (BLAST). Herein we introduce these methods and tools, and demonstrate their application. We have found that capacity fade from automotive use has a much larger impact on second use value than resistance growth. Where capacity loss is driven by calendar effects more than cycling effects, average battery temperature during automotive service – which is often driven by climate – is found to be the single factor with the largest effect on remaining value. Installing hardware and software capabilities onboard the vehicle that can both infer remaining battery capacity from in-situ measurements, as well as track average battery temperature over time, will thereby facilitate the second use of automotive batteries.

  7. Electrical energy storage for the grid: a battery of choices.

    Science.gov (United States)

    Dunn, Bruce; Kamath, Haresh; Tarascon, Jean-Marie

    2011-11-18

    The increasing interest in energy storage for the grid can be attributed to multiple factors, including the capital costs of managing peak demands, the investments needed for grid reliability, and the integration of renewable energy sources. Although existing energy storage is dominated by pumped hydroelectric, there is the recognition that battery systems can offer a number of high-value opportunities, provided that lower costs can be obtained. The battery systems reviewed here include sodium-sulfur batteries that are commercially available for grid applications, redox-flow batteries that offer low cost, and lithium-ion batteries whose development for commercial electronics and electric vehicles is being applied to grid storage. PMID:22096188

  8. Performance requirements of automotive batteries for future car electrical systems

    Science.gov (United States)

    Friedrich, R.; Richter, G.

    The further increase in the number of power-consuming functions which has been announced for future vehicle electrical systems, and in particular the effects of new starting systems on battery performance, requires a further optimization of the lead acid system coupled with effective energy management, and enhanced battery operating conditions. In the face of these increased requirements, there are proven benefits to splitting the functions of a single SLI battery between two separate, special-purpose batteries, each of which are optimized, for high power output and for high energy throughput, respectively. This will bring about a marked improvement in weight, reliability, and state of charge (SOC). The development of special design starter and service batteries is almost completed and will lead to new products with a high standard of reliability. The design of the power-optimized lead acid accumulator is particularly suitable for further development as the battery for a 42/36 V electrical system. This is intended to improve the efficiency of the generator and the various power-consuming functions and to improve start/stop operation thereby bringing about a marked reduction in the fuel consumption of passenger cars. This improvement can also be assisted by a charge management system used in conjunction with battery status monitoring.

  9. Updating United States Advanced Battery Consortium and Department of Energy battery technology targets for battery electric vehicles

    Science.gov (United States)

    Neubauer, Jeremy; Pesaran, Ahmad; Bae, Chulheung; Elder, Ron; Cunningham, Brian

    2014-12-01

    Battery electric vehicles (BEVs) offer significant potential to reduce the nation's consumption of petroleum based products and the production of greenhouse gases however, their widespread adoption is limited largely by the cost and performance limitations of modern batteries. With recent growth in efforts to accelerate BEV adoption (e.g. the Department of Energy's (DOE) EV Everywhere Grand Challenge) and the age of existing BEV battery technology targets, there is sufficient motivation to re-evaluate the industry's technology targets for battery performance and cost. Herein we document the analysis process that supported the selection of the United States Advanced Battery Consortium's (USABC) updated BEV battery technology targets. Our technology agnostic approach identifies the necessary battery performance characteristics that will enable the vehicle level performance required for a commercially successful, mass market full BEV, as guided by the workgroup's OEM members. The result is an aggressive target, implying that batteries need to advance considerably before BEVs can be both cost and performance competitive with existing petroleum powered vehicles.

  10. Optimal energy management strategy for battery powered electric vehicles

    International Nuclear Information System (INIS)

    Highlights: • The power usage for battery-powered electrical vehicles with in-wheel motors is maximized. • The battery and motor dynamics are examined emphasized on the power conversion and utilization. • The optimal control strategy is derived and verified by simulations. • An analytic expression of the optimal operating point is obtained. - Abstract: Due to limited energy density of batteries, energy management has always played a critical role in improving the overall energy efficiency of electric vehicles. In this paper, a key issue within the energy management problem will be carefully tackled, i.e., maximizing the power usage of batteries for battery-powered electrical vehicles with in-wheel motors. To this end, the battery and motor dynamics will be thoroughly examined with particular emphasis on the power conversion and power utilization. The optimal control strategy will then be derived based on the analysis. One significant contribution of this work is that an analytic expression for the optimal operating point in terms of the component and environment parameters can be obtained. Owing to this finding, the derived control strategy is also rendered a simple structure for real-time implementation. Simulation results demonstrate that the proposed strategy works both adaptively and robustly under different driving scenarios

  11. The Shortest Path Problems in Battery-Electric Vehicle Dispatching with Battery Renewal

    Directory of Open Access Journals (Sweden)

    Minfang Huang

    2016-06-01

    Full Text Available Electric vehicles play a key role for developing an eco-sustainable transport system. One critical component of an electric vehicle is its battery, which can be quickly charged or exchanged before it runs out. The problem of electric vehicle dispatching falls into the category of the shortest path problem with resource renewal. In this paper, we study the shortest path problems in (1 electric transit bus scheduling and (2 electric truck routing with time windows. In these applications, a fully-charged battery allows running a limited operational distance, and the battery before depletion needs to be quickly charged or exchanged with a fully-charged one at a battery management facility. The limited distance and battery renewal result in a shortest path problem with resource renewal. We develop a label-correcting algorithm with state space relaxation to find optimal solutions. In the computational experiments, real-world road geometry data are used to generate realistic travel distances, and other types of data are obtained from the real world or randomly generated. The computational results show that the label-correcting algorithm performs very well.

  12. Lithium Ion Batteries in Electric Drive Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Pesaran, Ahmad A.

    2016-05-16

    This research focuses on the technical issues that are critical to the adoption of high-energy-producing lithium Ion batteries. In addition to high energy density / high power density, this publication considers performance requirements that are necessary to assure lithium ion technology as the battery format of choice for electrified vehicles. Presentation of prime topics includes: long calendar life (greater than 10 years); sufficient cycle life; reliable operation under hot and cold temperatures; safe performance under extreme conditions; end-of-life recycling. To achieve aggressive fuel economy standards, carmakers are developing technologies to reduce fuel consumption, including hybridization and electrification. Cost and affordability factors will be determined by these relevant technical issues which will provide for the successful implementation of lithium ion batteries for application in future generations of electrified vehicles.

  13. Built-in electric field thickness design for betavoltaic batteries

    Institute of Scientific and Technical Information of China (English)

    Chen Haiyang; Li Darang; Yin Jianhua; Cai Shengguo

    2011-01-01

    Isotope source energy deposition along the thickness direction of a semiconductor is calculated,based upon which an ideal short current is evaluated for betavoltaic batteries.Electron-hole pair recombination and drifting length in a PN junction built-in electric field are extracted by comparing the measured short currents with the ideal short currents.A built-in electric field thickness design principle is proposed for betavoltaic batteries:after measuring the energy deposition depth and the carrier drift length,the shorter one should then be chosen as the built-in electric field thickness.If the energy deposition depth is much larger than the carrier drift length,a multijunction is preferred in betavoltaic batteries and the number of the junctions should be the value of the deposition depth divided by the drift length.

  14. An Electric taxi fleet charging system using second life electric car batteries simulation and economical approach

    OpenAIRE

    Canals Casals, Lluc; Amante García, Beatriz

    2013-01-01

    The industrial car manufacturers see in the high battery price an im-portant obstacle for an electric vehicle mass selling, thus mass production. There-fore, in order to find some cost relieves and better selling opportunities, they look and push forward to find profitable second battery uses. This study presents a sim-ulation and an economical approach for an electric taxi fleet charging system, us-ing these “old” electric car batteries, implemented in the city of Barcelona. The simulation w...

  15. Lithium Battery Power Delivers Electric Vehicles to Market

    Science.gov (United States)

    2008-01-01

    Hybrid Technologies Inc., a manufacturer and marketer of lithium-ion battery electric vehicles, based in Las Vegas, Nevada, and with research and manufacturing facilities in Mooresville, North Carolina, entered into a Space Act Agreement with Kennedy Space Center to determine the utility of lithium-powered fleet vehicles. NASA contributed engineering expertise for the car's advanced battery management system and tested a fleet of zero-emission vehicles on the Kennedy campus. Hybrid Technologies now offers a series of purpose-built lithium electric vehicles dubbed the LiV series, aimed at the urban and commuter environments.

  16. Unprecedented alliance in preparation for electric vehicle battery recycling

    Energy Technology Data Exchange (ETDEWEB)

    Miller, D.G. [Toxco Inc., Anaheim, CA (United States)

    2000-07-01

    As electric and hybrid vehicles gain a larger part of the automobile market, it is expected that large volumes of electric and hybrid vehicles lead, nickel, and lithium batteries will be required. To meet the demand, the largest recycler of lithium batteries in the world, Toxco Inc. formed an alliance with Kinsbursky Brothers Inc. (KBI). KBI is considered to be one of the most reputable and largest non-lithium battery management companies in the United States. The objective of the alliance is to offer a one-stop battery recycling service with direct recycling facilities, a single point for battery management and recycling. The elimination of the middle-man in the recycling process and the elimination of the redundant logistics are expected to yield cost savings, both for the companies and the customers. This recycling service is offered for all common and other battery types. A major benefit of the recycling program is found in the reduction of volumes of hazardous and/or reactive waste in incineration facilities or landfills. tabs., figs.

  17. Electric car batteries: Avoiding the environmental drawbacks via alternative technologies

    Science.gov (United States)

    Warlimont, Hans; Olper, Marco

    1996-07-01

    In this article, we address the question of whether air pollution resulting from the pyrometallurgical winning, recycling, and casting of lead for car batteries is a serious threat to the environmental acceptability of introducing electric cars. Specifically, we describe an alternative to pyrometallurgical processes—an electrochemical process called CX-EWS that can be used for the winning and recycling of lead. Also presented is a new manufacturing route for battery grids; it employs a combination of electroforming, the codeposition of dispersoids, and the electrowinning of spent batteries. The technology cannot only eliminate the casting of conventional or expanded metal grids but can also serve to reduce battery weight and, thus, increase energy density.

  18. Effects of Exchanging Battery on the Electric Vehicle’s Electricity Consumption in a Single-Lane Traffic System

    OpenAIRE

    Shi-Chun Yang; Wen-Zhuang Gou; Tie-Qiao Tang; Hua-Yan Shang

    2014-01-01

    We propose a car-following model to explore the influences of exchanging battery on each vehicle’s electricity consumption under three traffic situations from the numerical perspective. The numerical results show that exchanging battery will destroy the stability of traffic flow, but the effects are related to each vehicle’s initial headway, the time that each electric vehicle exchanges the battery, the proportion of the electric vehicles that should exchange the battery, the number of chargi...

  19. Motor Integrated Permanent Magnet Gear in a Battery Electrical Vehicle

    DEFF Research Database (Denmark)

    Frandsen, Tommy; Mathe, Laszlo; Berg, Nick Ilsø;

    2015-01-01

    This paper presents the physical construction and test results of two new demonstrators of a Motor Integrated Permanent Magnet Gear (MIPMG), which is a second version of an already tested demonstrator. The demonstrators will be used as traction units for a Battery Electrical Vehicle (BEV) and the...... used as traction unit in urban traffic....

  20. Zebra battery technologies for all electric smart car

    OpenAIRE

    O'Sullivan, T M; Bingham, Chris; Clark, R E

    2006-01-01

    This paper describes the operational behaviour and advantages of the high temperature, sodium nickel chloride (Zebra) battery, for use in all electric urban (city) vehicles. It is shown that an equivalent parallel electrical circuit can be employed to accurately simulate the electrochemical behaviour inherent in the most recent generation of Zebra cells. The experimental procedure is outlined and summary attributes of the investigation validated by both simulation studies, and experimentally,...

  1. Battery System Modeling for a Military Electric Propulsion Vehicle with a Fault Simulation

    OpenAIRE

    Hyeongcheol Lee; Kyuhong Han; Hyeongjin Ham

    2013-01-01

    This paper describes the development process and results of a battery system model with a fault simulation for electric propulsion vehicles. The developed battery system model can be used to verify control and fault diagnosis strategies of the supervisory controller in an electric propulsion vehicle. To develop this battery system model, three sub-models, including a battery model, a relay assembly model, and a battery management system (BMS) model, are connected together like in the target r...

  2. Battery Test Manual For Electric Vehicles, Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    Christophersen, Jon P. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-06-01

    This battery test procedure manual was prepared for the United States Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Vehicle Technologies Office. It is based on technical targets for commercial viability established for energy storage development projects aimed at meeting system level DOE goals for Electric Vehicles (EV). The specific procedures defined in this manual support the performance and life characterization of advanced battery devices under development for EVs. However, it does share some methods described in the previously published battery test manual for plug-in hybrid electric vehicles. Due to the complexity of some of the procedures and supporting analysis, future revisions including some modifications and clarifications of these procedures are expected. As in previous battery and capacitor test manuals, this version of the manual defines testing methods for full-size battery systems, along with provisions for scaling these tests for modules, cells or other subscale level devices. The DOE-United States Advanced Battery Consortium (USABC), Technical Advisory Committee (TAC) supported the development of the manual. Technical Team points of contact responsible for its development and revision are Chul Bae of Ford Motor Company and Jon P. Christophersen of the Idaho National Laboratory. The development of this manual was funded by the Unites States Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Office. Technical direction from DOE was provided by David Howell, Energy Storage R&D Manager and Hybrid Electric Systems Team Leader. Comments and questions regarding the manual should be directed to Jon P. Christophersen at the Idaho National Laboratory (jon.christophersen@inl.gov).

  3. Design options for automotive batteries in advanced car electrical systems

    Science.gov (United States)

    Peters, K.

    The need to reduce fuel consumption, minimize emissions, and improve levels of safety, comfort and reliability is expected to result in a much higher demand for electric power in cars within the next 5 years. Forecasts vary, but a fourfold increase in starting power to 20 kW is possible, particularly if automatic stop/start features are adopted to significantly reduce fuel consumption and exhaust emissions. Increases in the low-rate energy demand are also forecast, but the use of larger alternators may avoid unacceptable high battery weights. It is also suggested from operational models that the battery will be cycled more deeply. In examining possible designs, the beneficial features of valve-regulated lead-acid batteries made with compressed absorbent separators are apparent. Several of their attributes are considered. They offer higher specific power, improved cycling capability and greater vibration resistance, as well as more flexibility in packaging and installation. Optional circuits considered for dual-voltage supplies are separate batteries for engine starting (36 V) and low-power duties (12 V), and a universal battery (36 V) coupled to a d.c.-d.c. converter for a 12-V equipment. Battery designs, which can be made on commercially available equipment with similar manufacturing costs (per W h and per W) to current products, are discussed. The 36-V battery, made with 0.7 mm thick plates, in the dual-battery system weighs 18.5 kg and has a cold-cranking amp (CCA) rating of 790 A at -18°C to 21.6 V (1080 W kg -1 at a mean voltage of 25.4 V). The associated, cycleable 12-V battery, provides 1.5 kW h and weighs 24.6 kg. Thus, the combined battery weight is 43.1 kg. The single universal battery, with cycling capability, weighs 45.4 kg, has a CCA rating of 810 A (441 W kg -1 at a mean voltage of 24.7 V), and when connected to the d.c.-d.c. converter at 75% efficiency provides a low-power capacity of 1.5 kW h.

  4. Performance of Batteries for electric vehicles on shorter and longer term

    NARCIS (Netherlands)

    Gerssen-Gondelach, S.J.; Faaij, A.P.C.

    2012-01-01

    In this work, the prospects of available and new battery technologies for battery electric vehicles (BEVs) are examined. Five selected battery technologies are assessed on battery performance and cost in the short, medium and long term. Driving cycle simulations are carried out to assess the influen

  5. Performance of batteries for electric vehicles on short and longer term

    NARCIS (Netherlands)

    Gerssen - Gondelach, Sarah; Faaij, André P C

    2012-01-01

    In this work, the prospects of available and new battery technologies for battery electric vehicles (BEVs) are examined. Five selected battery technologies are assessed on battery performance and cost in the short, medium and long term. Driving cycle simulations are carried out to assess the influen

  6. Nickel cadmium battery evaluation, modeling, and application in an electric vehicle

    Science.gov (United States)

    Lynch, William Alfred

    A battery testing facility was set up in the battery evaluation laboratory. This system includes a set of current regulators which were fabricated in the UMASS. Lowell labs and a PC based data acquisition system. Batteries were charged or discharged at any rate within system ratings, and data including battery voltage, current, temperature and impedance were stored by a PC. STM5.140 type nickel-cadmium electric vehicle batteries were subjected to various test procedures using the battery testing facility. The results from these tests were used to determine battery characteristics. An electrical component battery model was also developed using the test data. The validity of the battery model was verified through experimental testing, and it was found to be accurate. Additionally, improved battery charging algorithms were developed which resulted in significant improvements in battery efficiency. Electric car operation with STM5.140 type of batteries was evaluated. Realistic road test data were analyzed experimentally and using the battery model. No battery abuse was found under EV driving conditions. The performance of the STM5.140 battery under abuse conditions was evaluated and it was found that it performs reasonably well under all abuse conditions tested. The model and test methodologies may be incorporated into complete electric vehicle models in order to assist in the design and operation of current and future electric vehicles.

  7. The ZEBRA electric vehicle battery: power and energy improvements

    Science.gov (United States)

    Galloway, Roy C.; Haslam, Steven

    Vehicle trials with the first sodium/nickel chloride ZEBRA batteries indicated that the pulse power capability of the battery needed to be improved towards the end of the discharge. A research programme led to several design changes to improve the cell which, in combination, have improved the power of the battery to greater than 150 W kg -1 at 80% depth of discharge. Bench and vehicle tests have established the stability of the high power battery over several years of cycling. The gravimetric energy density of the first generation of cells was less than 100 Wh kg -1. Optimisation of the design has led to a cell with a specific energy of 120 Wh kg -1 or 86 Wh kg -1 for a 30 kWh battery. Recently, the cell chemistry has been altered to improve the useful capacity. The cell is assembled in the over-discharged state and during the first charge the following reactions occur: at 1.6 V: Al+4NaCl=NaAlCl 4+3Na; at 2.35 V: Fe+2NaCl=FeCl 2+2Na; at 2.58 V: Ni+2NaCl=NiCl 2+2 Na. The first reaction serves to prime the negative sodium electrode but occurs at too low a voltage to be of use in providing useful capacity. By minimising the aluminium content more NaCl is released for the main reactions to improve the capacity of the cell. This, and further composition optimisation, have resulted in cells with specific energies in excess of 140 Wh kg -1, which equates to battery energies>100 Wh kg -1. The present production battery, as installed in a Mercedes Benz A class electric vehicle, gives a driving range of 205 km (128 miles) in city and hill climbing. The cells with improved capacity will extend the practical driving range to beyond 240 km (150 miles).

  8. Modeling of electric vehicle battery for vehicle-to-grid applications

    DEFF Research Database (Denmark)

    Pang, Ying; Brady, Cormac; Pellegrino, Giustino;

    2013-01-01

    Electric vehicle battery models are essential when performing analysis of EV systems. The battery package of electric vehicles is complicated and unpredictable because of its chemical based functioning. In this paper, a battery model is presented with a number of internal and external factors taken...

  9. Electric power from differences in salinity: the dialytic battery.

    Science.gov (United States)

    Weinstein, J N; Leitz, F B

    1976-02-13

    An array of alternating anion and cation exchange membranes can be used to generate electric power from the free energy of mixing of river and sea waters. A simple mathematical model, which predicts experimental results well, is useful in exploring conditions for optimization of the process. Major, but not impossible, improvements in technology would be required to bring the cost of power from the dialytic battery into line with foreseeable energy prices. PMID:17792805

  10. The maximum work output of an electric battery in a given time

    Energy Technology Data Exchange (ETDEWEB)

    Jincan Chen; Zheqiang Shi [Xiamen Univ., Dept. of Physics, Xiamen (China); Xuyang Chen [Center of Television Transmission, Xiamen (China)

    2002-10-01

    A new model of an electric battery is established, based on the simplest battery model and Denno's battery model with an internal dissipation. The model is used to investigate the fundamental problem of how to maximize the work output of an electric battery in a given time. The important relation of the voltage across the battery terminals varying with the discharging time is derived by using variational calculus. The maximum work output of the battery is calculated. The optimal matching condition of the load resistance is determined. The reasonable range of the discharging time is given. The other characteristics of the battery at the maximum work output are discussed further. The results obtained here have some theoretical applications not only for raising the utilization of the electric energy stored in batteries, but also for improving the performance of some electric circuits. (Author)

  11. Plug-in Hybrid and Battery Electric Vehicles. Market penetration scenarios of electric drive vehicles

    OpenAIRE

    Francoise Nemry; Martijn Brons

    2010-01-01

    Electric-drive vehicles (EDVs) are currently emerging in the market and are seen as a promising option towards a less carbon intensive road transport. This report presents a prospective analysis in relation with two of the current bottlenecks for the diffusion of electric vehicles. These concern batteries performance and cost, and the access to charging infrastructures. Based on projections on these factors, the analysis develops scenarios for the future market for electric cars and provides ...

  12. Plug-in hybrid electric vehicles: battery degradation, grid support, emissions, and battery size tradeoffs

    Science.gov (United States)

    Peterson, Scott B.

    Plug-in hybrid electric vehicles (PHEVs) may become a substantial part of the transportation fleet in a decade or two. This dissertation investigates battery degradation, and how introducing PHEVs may influence the electricity grid, emissions, and petroleum use in the US. It examines the effects of combined driving and vehicle-to-grid (V2G) usage on lifetime performance of commercial Li-ion cells. The testing shows promising capacity fade performance: more than 95% of the original cell capacity remains after thousands of driving days. Statistical analyses indicate that rapid vehicle motive cycling degraded the cells more than slower, V2G galvanostatic cycling. These data are used to examine the potential economic implications of using vehicle batteries to store grid electricity generated at off-peak hours for off-vehicle use during peak hours. The maximum annual profit with perfect market information and no battery degradation cost ranged from ˜US140 to 250 in the three cities. If measured battery degradation is applied the maximum annual profit decreases to ˜10-120. The dissertation predicts the increase in electricity load and emissions due to vehicle battery charging in PJM and NYISO with the current generators, with a 50/tonne CO2 price, and with existing coal generators retrofitted with 80% CO2 capture. It also models emissions using natural gas or wind+gas. We examined PHEV fleet percentages between 0.4 and 50%. Compared to 2020 CAFE standards, net CO2 emissions in New York are reduced by switching from gasoline to electricity; coal-heavy PJM shows smaller benefits unless coal units are fitted with CCS or replaced with lower CO2 generation. NOX is reduced in both RTOs, but there is upward pressure on SO2 emissions or allowance prices under a cap. Finally the dissertation compares increasing the all-electric range (AER) of PHEVs to installing charging infrastructure. Fuel use was modeled with National Household Travel Survey and Greenhouse Gasses, Regulated

  13. Battery electric vehicles - implications for the driver interface.

    Science.gov (United States)

    Neumann, Isabel; Krems, Josef F

    2016-03-01

    The current study examines the human-machine interface of a battery electric vehicle (BEV) from a user-perspective, focussing on the evaluation of BEV-specific displays, the relevance of provided information and challenges for drivers due to the concept of electricity in a road vehicle. A sample of 40 users drove a BEV for 6 months. Data were gathered at three points of data collection. Participants perceived the BEV-specific displays as only moderately reliable and helpful for estimating the displayed parameters. This was even less the case after driving the BEV for 3 months. A taxonomy of user requirements was compiled revealing the need for improved and additional information, especially regarding energy consumption and efficiency. Drivers had difficulty understanding electrical units and the energy consumption of the BEV. On the background of general principles for display design, results provide implications how to display relevant information and how to facilitate drivers' understanding of energy consumption in BEVs. Practitioner Summary: Battery electric vehicle (BEV) displays need to incorporate new information. A taxonomy of user requirements was compiled revealing the need for improved and additional information in the BEV interface. Furthermore, drivers had trouble understanding electrical units and energy consumption; therefore, appropriate assistance is required. Design principles which are specifically important in the BEV context are discussed. PMID:26444273

  14. Results of electric-vehicle propulsion system performance on three lead-acid battery systems

    Science.gov (United States)

    Ewashinka, J. G.

    1984-01-01

    Three types of state of the art 6 V lead acid batteries were tested. The cycle life of lead acid batteries as a function of the electric vehicle propulsion system design was determined. Cycle life, degradation rate and failure modes with different battery types (baseline versus state of the art tubular and thin plate batteries) were compared. The effects of testing strings of three versus six series connected batteries on overall performance were investigated. All three types do not seem to have an economically feasible battery system for the propulsion systems. The tubular plate batteries on the load leveled profile attained 235 cycles with no signs of degradation and minimal capacity loss.

  15. Integral inverter/battery charger for use in electric vehicles

    Science.gov (United States)

    Thimmesch, D.

    1983-01-01

    The design and test results of a thyristor based inverter/charger are discussed. A battery charger is included integral to the inverter by using a subset of the inverter power circuit components. The resulting charger provides electrical isolation between the vehicle propulsion battery and ac line and is capable of charging a 25 kWh propulsion battery in 8 hours from a 220 volt ac line. The integral charger employs the inverter commutation components at a resonant ac/dc isolated converter rated at 3.6 kW. Charger efficiency and power factor at an output power of 3.6 kW are 86% and 95% respectively. The inverter, when operated with a matching polyphase ac induction motor and nominal 132 volt propulsion battery, can provide a peak shaft power of 34 kW (45 ph) during motoring operation and 45 kW (60 hp) during regeneration. Thyristors are employed for the inverter power switching devices and are arranged in an input-commutated topology. This configuration requires only two thyristors to commutate the six main inverter thyristors. Inverter efficiency during motoring operation at motor shaft speeds above 450 rad/sec (4300 rpm) is 92-94% for output power levels above 11 KW (15 hp). The combined ac inverter/charger package weighs 47 kg (103 lbs).

  16. Design of an onboard battery charger for an electric vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Heckford, Simon

    2001-07-01

    This report describes the design of an on-board battery charger for an electric car. There are already various battery charger units on the market. However, these are not specifically designed for this application, and consequently do not provide an ideal solution. Because these products are not specific to one application, and instead opt to cover a variety of briefs, they are not ideal. They also tend to be heavier and more expensive than if the charger was built specifically for one purpose. The main design considerations were that the charger should be compact and lightweight. It was also specified that the design should be able to operate using either the single-phase or three-phase AC supply. Before the design process for the battery charger could commence, it was necessary for the author to get an appreciation of power electronics, since he had no previous experience in the subject. The author focused his attention on areas of the subject most valuable to the project, including becoming familiar with the principle behind battery chargers. Once the required knowledge was obtained, the author could begin designing the charger. The majority of the design was actually undertaken using two software packages called MATLAB and Simulink, whilst also using the knowledge acquired. Regular discussions were had with the project team in order to ensure that the correct methodology was being used and a suitable design was duly developed. Possible further work was identified which could not be carried out within the time constraints of this project.

  17. Impact of Battery Ageing on an Electric Vehicle Powertrain Optimisation

    Directory of Open Access Journals (Sweden)

    Daniel J. Auger

    2014-12-01

    Full Text Available An electric vehicle’s battery is its most expensive component, and it cannot be charged and discharged indefinitely. This affects a consumer vehicle’s end-user value. Ageing is tolerated as an unwanted operational side-effect; manufacturers have little control over it. Recent publications have considered trade-offs between efficiency and ageing in plug-in hybrids (PHEVs but there is no equivalent literature for pure EVs. For PHEVs, battery ageing has been modelled by translating current demands into chemical degradation. Given such models it is possible to produce similar trade-offs for EVs. We consider the effects of varying battery size and introducing a parallel supercapacitor pack. (Supercapacitors can smooth current demands, but their weight and electronics reduce economy. We extend existing EV optimisation techniques to include battery ageing, illustrated with vehicle case studies. We comment on the applicability to similar EV problems and identify where additional research is needed to improve on our assumptions.

  18. Research, development, and demonstration of lead-acid batteries for electric vehicle propulsion. Annual report, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    The progress and status of Eltra's Electric Vehicle Battery Program during FY-80 are presented under five divisional headings: Research on Components and Processes; Development of Cells and Modules for Electric Vehicle Propulsion; Sub-Systems; Pilot Line Production of Electric Vehicle Battery Prototypes; and Program Management.

  19. Performance characteristics of an electric vehicle lead-acid battery pack at elevated temperatures

    Science.gov (United States)

    Chapman, P.

    1982-01-01

    Discharge testing data electric car battery pack over initial electrolyte temperature variations between 27 and 55 C are presented. The tests were conducted under laboratory conditions and then compared to detailed electric vehicle simulation models. Battery discharge capacity increased with temperature for constant current discharges, and battery energy capacity increased with temperature for constant power discharges. Dynamometer tests of the electric test vehicle showed an increase in range of 25% for the higher electrolyte temperature.

  20. Influence of Battery/Ultracapacitor Energy-Storage Sizing on Battery Lifetime in a Fuel Cell Hybrid Electric Vehicle

    DEFF Research Database (Denmark)

    Schaltz, Erik; Rasmussen, Peter Omand; Khaligh, Alireza

    2009-01-01

    Combining high-energy-density batteries and high-power-density ultracapacitors in fuel cell hybrid electric vehicles (FCHEVs) results in a high-performance, highly efficient, low-size, and light system. Often, the battery is rated with respect to its energy requirement to reduce its volume and mass......, the battery, and the ultracapacitors, are proposed. A charging strategy, which charges the energy-storage devices due to the conditions of the FCHEV, is also proposed. The analysis provides recommendations on the design of the battery and the ultracapacitor energy-storage systems for FCHEVs....

  1. Effects of Exchanging Battery on the Electric Vehicle’s Electricity Consumption in a Single-Lane Traffic System

    Directory of Open Access Journals (Sweden)

    Shi-Chun Yang

    2014-01-01

    Full Text Available We propose a car-following model to explore the influences of exchanging battery on each vehicle’s electricity consumption under three traffic situations from the numerical perspective. The numerical results show that exchanging battery will destroy the stability of traffic flow, but the effects are related to each vehicle’s initial headway, the time that each electric vehicle exchanges the battery, the proportion of the electric vehicles that should exchange the battery, the number of charging stations, and the distance between two adjacent charging stations.

  2. Modelling challenges for battery materials and electrical energy storage

    Science.gov (United States)

    Muller, Richard P.; Schultz, Peter A.

    2013-10-01

    Many vital requirements in world-wide energy production, from the electrification of transportation to better utilization of renewable energy production, depend on developing economical, reliable batteries with improved performance characteristics. Batteries reduce the need for gasoline and liquid hydrocarbons in an electrified transportation fleet, but need to be lighter, longer-lived and have higher energy densities, without sacrificing safety. Lighter and higher-capacity batteries make portable electronics more convenient. Less expensive electrical storage accelerates the introduction of renewable energy to electrical grids by buffering intermittent generation from solar or wind. Meeting these needs will probably require dramatic changes in the materials and chemistry used by batteries for electrical energy storage. New simulation capabilities, in both methods and computational resources, promise to fundamentally accelerate and advance the development of improved materials for electric energy storage. To fulfil this promise significant challenges remain, both in accurate simulations at various relevant length scales and in the integration of relevant information across multiple length scales. This focus section of Modelling and Simulation in Materials Science and Engineering surveys the challenges of modelling for energy storage, describes recent successes, identifies remaining challenges, considers various approaches to surmount these challenges and discusses the potential of these methods for future battery development. Zhang et al begin with atoms and electrons, with a review of first-principles studies of the lithiation of silicon electrodes, and then Fan et al examine the development and use of interatomic potentials to the study the mechanical properties of lithiated silicon in larger atomistic simulations. Marrocchelli et al study ionic conduction, an important aspect of lithium-ion battery performance, simulated by molecular dynamics. Emerging high

  3. Average Behavior of Battery - Electric Vehicles for Distributed Energy System Studies

    DEFF Research Database (Denmark)

    Marra, Francesco; Træholt, Chresten; Larsen, Esben;

    2010-01-01

    The increase of focus on electric vehicles (EVs) as distributed energy resources calls for new concepts of aggregated models of batteries. Despite the developed battery models for EVs applications, when looking at energy storage scenarios using EVs, both geographical-temporal aspects and battery...... use conditions cannot be neglected for a proper estimation of available fleet energy. In this paper we describe an average behavior of battery-EVs. Main points of this concept include the definition of the energy window and lifetime of the batteries, in relation to existing models and battery use...

  4. Modeling and Validation of Lithium-Ion Battery based on Electric Vehicle Measurement

    OpenAIRE

    SIMIC Dragan; DVORAK Dominique; LACHER Hannes; KUEHNELT Helmut; PAFFUMI Elena; DE GENNARO MICHELE

    2013-01-01

    This contribution deals with the development, modeling and validation of multi-physical battery-models using the description language Modelica. The battery model can be used in any scenario where a simulation of the electric, thermal or aging behavior of a lithium-ion battery is of interest. Furthermore a concept is provided, which allows extracting the open circuit voltage of the battery directly from the raw measurement data. On the basis of the measurements, a data set which can be used...

  5. Intelligent energy systems - Regulating the electricity grid using car batteries

    International Nuclear Information System (INIS)

    This article takes a look at how the electricity supply industry will, in the future, be able to substantially rely on decentrally organised sources of renewable energy. As such forms of power generation are, in part, difficult to plan, the increasing importance of regulating energy is being stressed. The use of the batteries of plug-in hybrid vehicles to provide such regulating power is discussed. So-called smart grids within the framework of a deregulated energy market are discussed and examples of possible configurations are noted. The intelligent control of apparatus and generation and storage facilities is discussed. Individual mobility with lower emissions is examined. New business areas now opening up for the electricity economy and vehicle manufacturers are discussed.

  6. An unusual electrical burn caused by alkaline batteries.

    Science.gov (United States)

    Roan, Tyng-Luen; Yeong, Eng-Kean; Tang, Yueh-Bih

    2015-02-01

    Electrical burns caused by low-voltage batteries are rarely reported. We recently encountered a male patient who suffered from a superficial second-degree burn over his left elbow and back. The total body surface area of the burn was estimated to be 6%. After interviewing the patient, the cause was suspected to be related to the explosion of a music player on the left-side of his waist, carried on his belt while he was painting a bathroom wall. Elevated creatine kinase levels and hematuria indicated rhabdomyolysis and suggested an electrical burn. Initial treatment was done in the burn intensive care unit with fluid challenge and wound care. The creatine kinase level decreased gradually and the hematuria was gone after 4 days in the intensive care unit. He was then transferred to the general ward for further wound management and discharged from our burn center after a total of 11 days without surgical intervention. PMID:25678181

  7. Electric vehicle batteries reports of the PPP European green vehicles initiative

    CERN Document Server

    Briec, Emma

    2014-01-01

    This edited volume presents research results of the PPP European Green Vehicle Initiative (EGVI), focusing on electric vehicle batteries. Electrification is one road towards sustainable road transportation, and battery technology is one of the key enabling technologies. However, at the same time, battery technology is one of the main obstacles for a broad commercial launch of electric vehicles. This book includes research contributions which try to bridge the gap between research and innovation in the field of battery technology for electric vehicles. The target audience primarily comprises r

  8. Battery Sizing for Plug-in Hybrid Electric Vehicles in Beijing: A TCO Model Based Analysis

    Directory of Open Access Journals (Sweden)

    Cong Hou

    2014-08-01

    Full Text Available This paper proposes a total cost of ownership (TCO model for battery sizing of plug-in hybrid electric vehicles (PHEVs. The proposed systematic TCO model innovatively integrates the Beijing driving database and optimal PHEV energy management strategies developed earlier. The TCO, including battery, fuel, electricity, and salvage costs, is calculated in yearly cash flows. The salvage cost, based on battery degradation model, is proposed for the first time. The results show that the optimal battery size for PHEVs in Beijing is 6–8 kWh. Several additional scenarios are also analyzed: (1 10% increase in battery price or discount rate leads to an optimal battery size of 6 kWh, and 10% increase in fuel price shifts the optimal battery size to 8 kWh; (2 the longer and more dispersive daily range distribution in the U.S. increases the optimal battery size to 14 kWh; (3 the subsidy in China results in an optimal battery size of 13 kWh, while that in the U.S. results in 17 kWh, and a fuel savings rate based subsidy policy is innovatively proposed; (4 the optimal battery size with Li4Ti5O12 batteries is 2 kWh, but the TCO of Li4Ti5O12 batteries is higher than that of LiFePO4 batteries.

  9. Battery Sizing for Plug-in Hybrid Electric Vehicles in Beijing: A TCO Model Based Analysis

    OpenAIRE

    Cong Hou; Hewu Wang; Minggao Ouyang

    2014-01-01

    This paper proposes a total cost of ownership (TCO) model for battery sizing of plug-in hybrid electric vehicles (PHEVs). The proposed systematic TCO model innovatively integrates the Beijing driving database and optimal PHEV energy management strategies developed earlier. The TCO, including battery, fuel, electricity, and salvage costs, is calculated in yearly cash flows. The salvage cost, based on battery degradation model, is proposed for the first time. The results show that the optimal b...

  10. Electromechanical battery mass minimization, taking into account its electrical machines rotor energy

    OpenAIRE

    Podgornovs, Andrejs; Sipovics, Antons

    2014-01-01

    In this paper electromechanical battery with synchronous machine, were described. Theoretically if is known electrical machines rotor stored energy, it is possible to reduce electromechanical battery flywheel mass. For rotor stored energy amount calculation, it is necessary to find all geometrical dimensions of electrical machine. To achieve this goal iterative calculation method was used. Electromechanical battery mass is analyzed as discharge process rotation speed function.

  11. Method of electric powertrain matching for battery-powered electric cars

    Science.gov (United States)

    Ning, Guobao; Xiong, Lu; Zhang, Lijun; Yu, Zhuoping

    2013-05-01

    The current match method of electric powertrain still makes use of longitudinal dynamics, which can't realize maximum capacity for on-board energy storage unit and can't reach lowest equivalent fuel consumption as well. Another match method focuses on improving available space considering reasonable layout of vehicle to enlarge rated energy capacity for on-board energy storage unit, which can keep the longitudinal dynamics performance almost unchanged but can't reach lowest fuel consumption. Considering the characteristics of driving motor, method of electric powertrain matching utilizing conventional longitudinal dynamics for driving system and cut-and-try method for energy storage system is proposed for passenger cars converted from traditional ones. Through combining the utilization of vehicle space which contributes to the on-board energy amount, vehicle longitudinal performance requirements, vehicle equivalent fuel consumption level, passive safety requirements and maximum driving range requirement together, a comprehensive optimal match method of electric powertrain for battery-powered electric vehicle is raised. In simulation, the vehicle model and match method is built in Matlab/simulink, and the Environmental Protection Agency (EPA) Urban Dynamometer Driving Schedule (UDDS) is chosen as a test condition. The simulation results show that 2.62% of regenerative energy and 2% of energy storage efficiency are increased relative to the traditional method. The research conclusions provide theoretical and practical solutions for electric powertrain matching for modern battery-powered electric vehicles especially for those converted from traditional ones, and further enhance dynamics of electric vehicles.

  12. Going electric: Expert survey on the future of battery technologies for electric vehicles

    International Nuclear Information System (INIS)

    The paper describes the results of a survey carried out with leading EU experts on the future costs of batteries for electric and plug-in hybrid vehicles and the uncertainty surrounding them. Battery costs are one of the main components in the overall costs of EVs and improvements could be brought about by increased investments in research, development and demonstration (RD and D). Experts' judgements are collected to shed light on the inherently uncertain relationship between RD and D efforts and the consequent technical progress in batteries. The analysis of the experts' data results in a number of important policy recommendations to guide future RD and D choices and target commitments both for the EU and its member states. - Highlights: • EVS success is hampered by high costs and technical limits of battery systems. • R and D should support applied and demonstration activities for Li-ion and Ni-MH. • Battery cost in 2030 will be competitive only if R and D is doubled

  13. Electric Vehicle Based Battery Storages for Large Scale Wind Power Integration in Denmark

    DEFF Research Database (Denmark)

    Pillai, Jayakrishnan Radhakrishna

    In the recent years, the electric vehicles (EVs) have drawn great attention world wide as a feasible solution for clean transportation. The electric vehicle technology is not new as it was introduced in the mid 19th century. The low battery capacity, driving range and superior gasoline cars had...... resulted in the demise of electric cars in the 1930s. However, with the advancement of new high density battery technologies and power electronic converters, it is now viable to produce electric cars of higher efficiency and driving range. The performance and durability of the battery technology...... is improving on a rapid scale and the battery cost is also reducing which could enable the electric cars to be competitive in the market. The electric vehicles could also benefit the electricity sector in supporting more renewable energy which is also one of the most important driving forces in its promotion...

  14. Thru-life impacts of driver aggression, climate, cabin thermal management, and battery thermal management on battery electric vehicle utility

    Science.gov (United States)

    Neubauer, Jeremy; Wood, Eric

    2014-08-01

    Battery electric vehicles (BEVs) offer the potential to reduce both oil imports and greenhouse gas emissions, but have a limited utility that is affected by driver aggression and effects of climate-both directly on battery temperature and indirectly through the loads of cabin and battery thermal management systems. Utility is further affected as the battery wears through life in response to travel patterns, climate, and other factors. In this paper we apply the National Renewable Energy Laboratory's Battery Lifetime Analysis and Simulation Tool for Vehicles (BLAST-V) to examine the sensitivity of BEV utility to driver aggression and climate effects over the life of the vehicle. We find the primary challenge to cold-climate BEV operation to be inefficient cabin heating systems, and to hot-climate BEV operation to be high peak on-road battery temperatures and excessive battery degradation. Active cooling systems appear necessary to manage peak battery temperatures of aggressive, hot-climate drivers, which can then be employed to maximize thru-life vehicle utility.

  15. Investigation of Battery/Ultracapacitor Energy Storage Rating for a Fuel Cell Hybrid Electric Vehicle

    DEFF Research Database (Denmark)

    Schaltz, Erik; Khaligh, A.; Rasmussen, Peter Omand

    2008-01-01

    Combining high energy density batteries and high power density ultracapacitors in Fuel Cell Hybrid Electric Vehicles (FCHEV) results in a high efficient, high performance, low size, and light system. Often the batteries are rated with respect to their energy requirement in order to reduce...... their volume and mass. This does not prevent deep discharges of the batteries, which is critical to their lifetime. In this paper, the ratings of the batteries and ultracapacitors in a FCHEV are investigated. Comparison of system volume, mass, efficiency, and battery lifetime due to the rating of the energy...

  16. Ford/DOE sodium-sulfur battery electric vehicle development: Phase I-A final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-12-01

    Phase I-A NaS battery powered electric vehicle study program produced encouraging results insofar as showing that a feasible NaS battery design can be developed for installation in an existing production vehicle, such as the Ford Fiesta. The study has shown that this NaS Battery powered Fiesta (modified to be a 2-passenger vehicle), can have adequate performance and range potential such that its use as a test bed could adequately evaluate the potential of the NaS battery as a power source for further electric vehicles.

  17. Ensure the electric power system's durability through battery monitoring

    OpenAIRE

    Andersson, Jonas

    2015-01-01

    Battery monitoring is used to acquire information about battery conditions. It’s a regular technology that most of us uses on daily bases. The charge gauge in a cellphone, consisting of bars which indicate the degree of charge left in the battery is an example. Battery monitoring gives the cellphone user information about the battery. The background to the thesis work is that this technology is requested for vehicles because empty or broken batteries are one of the most common causes for invo...

  18. Ecological and biomedical effects of effluents from near-term electric vehicle storage battery cycles

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-01

    An assessment of the ecological and biomedical effects due to commercialization of storage batteries for electric and hybrid vehicles is given. It deals only with the near-term batteries, namely Pb/acid, Ni/Zn, and Ni/Fe, but the complete battery cycle is considered, i.e., mining and milling of raw materials, manufacture of the batteries, cases and covers; use of the batteries in electric vehicles, including the charge-discharge cycles; recycling of spent batteries; and disposal of nonrecyclable components. The gaseous, liquid, and solid emissions from various phases of the battery cycle are identified. The effluent dispersal in the environment is modeled and ecological effects are assessed in terms of biogeochemical cycles. The metabolic and toxic responses by humans and laboratory animals to constituents of the effluents are discussed. Pertinent environmental and health regulations related to the battery industry are summarized and regulatory implications for large-scale storage battery commercialization are discussed. Each of the seven sections were abstracted and indexed individually for EDB/ERA. Additional information is presented in the seven appendixes entitled; growth rate scenario for lead/acid battery development; changes in battery composition during discharge; dispersion of stack and fugitive emissions from battery-related operations; methodology for estimating population exposure to total suspended particulates and SO/sub 2/ resulting from central power station emissions for the daily battery charging demand of 10,000 electric vehicles; determination of As air emissions from Zn smelting; health effects: research related to EV battery technologies. (JGB)

  19. The UltraBattery-A new battery design for a new beginning in hybrid electric vehicle energy storage

    Science.gov (United States)

    Cooper, A.; Furakawa, J.; Lam, L.; Kellaway, M.

    The UltraBattery, developed by CSIRO Energy Technology in Australia, is a hybrid energy storage device which combines an asymmetric super-capacitor and a lead-acid battery in single unit cells. This takes the best from both technologies without the need for extra, expensive electronic controls. The capacitor enhances the power and lifespan of the lead-acid battery as it acts as a buffer during high-rate discharging and charging, thus enabling it to provide and absorb charge rapidly during vehicle acceleration and braking. The initial performance of the prototype UltraBatteries was evaluated according to the US FreedomCAR targets and was shown to meet or exceed these in terms of power, available energy, cold cranking and self-discharge set for both minimum and maximum power-assist hybrid electric vehicles (HEVs). Other laboratory cycling tests showed a fourfold improvement over previous state-of-the-art lead-acid batteries under the RHOLAB test profile and better life than commercial nickel/metal hydride (NiMH) cells used in a Honda Insight when tested under the EUCAR HEV profile. As a result of this work, a set of twelve 12 V modules was built by The Furukawa Battery Co., Ltd. in Japan and were fitted into a Honda Insight instead of the NiMH battery by Provector Ltd. The battery pack was fitted with full monitoring and control capabilities and the car was tested at Millbrook Proving Ground under a General Motors road test simulation cycle for an initial target of 50 000 miles which was extended to 100 000 miles. This was completed on 15th January 2008 without any battery problems. Furthermore, the whole test was completed without the need for any conditioning or equalisation of the battery pack.

  20. Influence of plug-in hybrid electric vehicle charging strategies on charging and battery degradation costs

    International Nuclear Information System (INIS)

    The profitability of plug-in hybrid electric vehicles (PHEVs) is significantly influenced by battery aging and electricity costs. Therefore a simulation model for PHEVs in the distribution grid is presented which allows to compare the influence of different charging strategies on these costs. The simulation is based on real-world driving behavior and European Energy Exchange (EEX) intraday prices for obtaining representative results. The analysis of comprehensive lithium-ion battery aging tests performed within this study shows that especially high battery states of charge (SOCs) decrease battery lifetime, whereas the cycling of batteries at medium SOCs only has a minor contribution to aging. Charging strategies that take into account the previously mentioned effects are introduced, and the SOC distributions and cycle loads of the vehicle battery are investigated. It can be shown that appropriate charging strategies significantly increase battery lifetime and reduce charging costs at the same time. Possible savings due to lifetime extension of the vehicle battery are approximately two times higher than revenues due to energy trading. The findings of this work indicate that car manufacturers and energy/mobility providers have to make efforts for developing intelligent charging strategies to reduce mobility costs and thus foster the introduction of electric mobility. - Highlights: ► Modeling of PHEVs based on real-world driving behavior and electricity prices. ► Consideration of battery degradation for the calculation of mobility costs. ► Smart charging decreases battery degradation and electricity costs simultaneously. ► Reduction of battery degradation costs is around two times higher than reduction of electricity costs.

  1. Use of lithium-ion batteries in electric vehicles

    Science.gov (United States)

    Kennedy, B.; Patterson, D.; Camilleri, S.

    An account is given of the lithium-ion (Li-ion) battery pack used in the Northern Territory University's solar car, Fuji Xerox Desert Rose, which competed in the 1999 World Solar Challenge (WSC). The reasons for the choice of Li-ion batteries over silver-zinc batteries are outlined, and the construction techniques used, the management of the batteries, and the battery protection boards are described. Data from both pre-race trialling and race telemetry, and an analysis of both the coulombic and the energy efficiencies of the battery are presented. It is concluded that Li-ion batteries show a real advantage over other commercially available batteries for traction applications of this kind.

  2. An Optimal Operating Strategy for Battery Life Cycle Costs in Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Yinghua Han

    2014-01-01

    Full Text Available Impact on petroleum based vehicles on the environment, cost, and availability of fuel has led to an increased interest in electric vehicle as a means of transportation. Battery is a major component in an electric vehicle. Economic viability of these vehicles depends on the availability of cost-effective batteries. This paper presents a generalized formulation for determining the optimal operating strategy and cost optimization for battery. Assume that the deterioration of the battery is stochastic. Under the assumptions, the proposed operating strategy for battery is formulated as a nonlinear optimization problem considering reliability and failure number. And an explicit expression of the average cost rate is derived for battery lifetime. Results show that the proposed operating strategy enhances the availability and reliability at a low cost.

  3. Structure improvement and electrochemical studies of bipolar nickel metal hydride batteries for hybrid electric vehicles

    Institute of Scientific and Technical Information of China (English)

    DENG Chao; SHI Peng-fei

    2006-01-01

    Nickel metal hydride battery in bipolar design offers some advantages for its application as a power storage system for electric and hybrid vehicles. This paper deals with the structure design and electrochemical studies of bipolar Ni/MH batteries for hybrid vehicles. An improvement is applied in bipolar battery design,and such bipolar Ni/MH batteries with 5 sub-cells have been assembled and investigated. Testing results show that bipolar batteries with improved structure have better compression tolerance and cycle performance than conventional ones. In addition, the improved bipolar batteries display excellent large current discharge ability and high power density. As simulating working conditions for hybrid vehicles, the batteries show good stability during pulse cycles, which verifies the possibility of being used as a power storage device on hybrid vehicles.

  4. Experiments Study on Charge Technology of Lead-Acid Electric Vehicle Batteries

    Institute of Scientific and Technical Information of China (English)

    LI Wen; ZHANG Cheng-ning

    2008-01-01

    The basic theory of the fast charge and several charge methods are introduced. In order to heighten charge efficiency of valve-regulated lead-acid battery and shorten the charge time, five charge methods are investigated with experiments done on the Digatron BNT 400-050 test bench. Battery current, terminal voltage, capacity, energy and terminal pole temperature during battery experiment were recorded, and corresponding curves were depicted. Battery capacity-time ratio, energy efficiency and energy-temperature ratio are put forward to be the appraising criteria of lead-acid battery on electric vehicle (EV). According to the appraising criteria and the battery curves, multistage-current/negative-pulse charge method is recommended to charge lead-acid EV battery.

  5. Performance characteristics of an electric-vehicle lead-acid battery pack at elevated temperatures

    Science.gov (United States)

    Chapman, P.

    1982-04-01

    Data are presented for discharge testing of an 18-Exide IV electric car battery pack over initial electrolyte temperature variations between 27 and 55 C. The tests were conducted under laboratory conditions and then compared to detailed electric vehicle simulation models. Results showed that battery discharge capacity increased with temperature for constant current discharges, and that battery energy capacity increased with temperature for constant power discharges. Dynamometer test of the GE Electric Test Vehicle showed an increase in range of 25% for the highest electrolyte temperature.

  6. Interdependencies of Home Energy Storage between Electric Vehicle and Stationary Battery

    OpenAIRE

    Kaschub, Thomas; Jochem, Patrick; Fichtner, Wolf

    2015-01-01

    Decentralized power generation in private homes, especially by photovoltaic systems, is already common in Germany. The developments of batteries, both for electric vehicles (EV) and for stationary storage might lead to a mass market for those batteries. In this paper we evaluate the economy of stationary battery storage with photovoltaic system at home in the context of available EV and its integration level into the home. Therefore, we use an optimization model with one year detailed operati...

  7. Cost and design study for electric vehicle lead--acid batteries

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    A design and cost study for electric-vehicle lead--acid batteries is presented; a research and development program leading to demonstration and testing of 20- to 30-kWh batteries is proposed. Both flat pasted and tubular positive electrodes are included. Detailed testing programs are set forth. 110 figures, 8 tables (RWR)

  8. Research, development and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    Activities in a program to develop a Ni/Zn battery for electric vehicle propulsion are reported. Aspects discussed include battery design and development, nickel cathode study, and basic electrochemistry. A number of engineering drawings are supplied. 61 figures, 11 tables. (RWR)

  9. Nickel-iron battery to be used in Peugeot electric car

    Science.gov (United States)

    1984-08-01

    The introduction of an electrically driven vehicle by the Peugeot group is announced. This is made possible by the development of a new nickel-iron battery. Advantages of this battery including weight and size reduction and improved life are briefly discussed.

  10. Predictive Model Based Battery Constraints for Electric Motor Control within EV Powertrains

    NARCIS (Netherlands)

    Roşca, B.; Wilkins, S.; Jacob, J.; Hoedemaekers, E.R.G.; Hoek, S.P. van den

    2014-01-01

    This paper presents a method of predicting the maximum power capability of a Li-Ion battery, to be used for electric motor control within automotive powertrains. As maximum power is highly dependent on battery state, the method consists of a pack level state observer coupled with a predictive batter

  11. Electric Vehicle Based Battery Storages for Future Power System Regulation Services

    DEFF Research Database (Denmark)

    Pillai, Jayakrishnan Radhakrishna; Bak-Jensen, Birgitte

    2009-01-01

    supplying the reserve power requirements. This limited regulation services from conventional generators in the future power system calls for other new reserve power solutions like Electric Vehicle (EV) based battery storages. A generic aggregated EV based battery storage for long-term dynamic load frequency...

  12. Ecological and biomedical effects of effluents from near-term electric vehicle storage battery cycles

    Science.gov (United States)

    1980-05-01

    The lead/acid battery cycle from mining and milling of raw materials through recycling of scrap batteries and disposal of wastes is described. Material flows and emissions for various phases of the total cycle are estimated for per megawatt hour of installed capacity and for a scenario of three million lead/acid electric vehicles on the road by the year 2000.

  13. The economics of using plug-in hybrid electric vehicle battery packs for grid storage

    Science.gov (United States)

    Peterson, Scott B.; Whitacre, J. F.; Apt, Jay

    We examine the potential economic implications of using vehicle batteries to store grid electricity generated at off-peak hours for off-vehicle use during peak hours. Ancillary services such as frequency regulation are not considered here because only a small number of vehicles will saturate that market. Hourly electricity prices in three U.S. cities were used to arrive at daily profit values, while the economic losses associated with battery degradation were calculated based on data collected from A123 Systems LiFePO 4/Graphite cells tested under combined driving and off-vehicle electricity utilization. For a 16 kWh (57.6 MJ) vehicle battery pack, the maximum annual profit with perfect market information and no battery degradation cost ranged from ∼US140 to 250 in the three cities. If the measured battery degradation is applied, however, the maximum annual profit (if battery pack replacement costs fall to 5000 for a 16 kWh battery) decreases to ∼10-120. It appears unlikely that these profits alone will provide sufficient incentive to the vehicle owner to use the battery pack for electricity storage and later off-vehicle use. We also estimate grid net social welfare benefits from avoiding the construction and use of peaking generators that may accrue to the owner, finding that these are similar in magnitude to the energy arbitrage profit.

  14. Optimal Battery Utilization Over Lifetime for Parallel Hybrid Electric Vehicle to Maximize Fuel Economy

    Energy Technology Data Exchange (ETDEWEB)

    Patil, Chinmaya; Naghshtabrizi, Payam; Verma, Rajeev; Tang, Zhijun; Smith, Kandler; Shi, Ying

    2016-08-01

    This paper presents a control strategy to maximize fuel economy of a parallel hybrid electric vehicle over a target life of the battery. Many approaches to maximizing fuel economy of parallel hybrid electric vehicle do not consider the effect of control strategy on the life of the battery. This leads to an oversized and underutilized battery. There is a trade-off between how aggressively to use and 'consume' the battery versus to use the engine and consume fuel. The proposed approach addresses this trade-off by exploiting the differences in the fast dynamics of vehicle power management and slow dynamics of battery aging. The control strategy is separated into two parts, (1) Predictive Battery Management (PBM), and (2) Predictive Power Management (PPM). PBM is the higher level control with slow update rate, e.g. once per month, responsible for generating optimal set points for PPM. The considered set points in this paper are the battery power limits and State Of Charge (SOC). The problem of finding the optimal set points over the target battery life that minimize engine fuel consumption is solved using dynamic programming. PPM is the lower level control with high update rate, e.g. a second, responsible for generating the optimal HEV energy management controls and is implemented using model predictive control approach. The PPM objective is to find the engine and battery power commands to achieve the best fuel economy given the battery power and SOC constraints imposed by PBM. Simulation results with a medium duty commercial hybrid electric vehicle and the proposed two-level hierarchical control strategy show that the HEV fuel economy is maximized while meeting a specified target battery life. On the other hand, the optimal unconstrained control strategy achieves marginally higher fuel economy, but fails to meet the target battery life.

  15. Life-cycle energy analyses of electric vehicle storage batteries. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, D; Morse, T; Patel, P; Patel, S; Bondar, J; Taylor, L

    1980-12-01

    The results of several life-cycle energy analyses of prospective electric vehicle batteries are presented. The batteries analyzed were: Nickel-zinc; Lead-acid; Nickel-iron; Zinc-chlorine; Sodium-sulfur (glass electrolyte); Sodium-sulfur (ceramic electrolyte); Lithium-metal sulfide; and Aluminum-air. A life-cycle energy analysis consists of evaluating the energy use of all phases of the battery's life, including the energy to build it, operate it, and any credits that may result from recycling of the materials in it. The analysis is based on the determination of three major energy components in the battery life cycle: Investment energy, i.e., The energy used to produce raw materials and to manufacture the battery; operational energy i.e., The energy consumed by the battery during its operational life. In the case of an electric vehicle battery, this energy is the energy required (as delivered to the vehicle's charging circuit) to power the vehicle for 100,000 miles; and recycling credit, i.e., The energy that could be saved from the recycling of battery materials into new raw materials. The value of the life-cycle analysis approach is that it includes the various penalties and credits associated with battery production and recycling, which enables a more accurate determination of the system's ability to reduce the consumption of scarce fuels. The analysis of the life-cycle energy requirements consists of identifying the materials from which each battery is made, evaluating the energy needed to produce these materials, evaluating the operational energy requirements, and evaluating the amount of materials that could be recycled and the energy that would be saved through recycling. Detailed descriptions of battery component materials, the energy requirements for battery production, and credits for recycling, and the operational energy for an electric vehicle, and the procedures used to determine it are discussed.

  16. Impact of lithium abundance and cost on electric vehicle battery applications

    Science.gov (United States)

    Will, Fritz G.

    This paper addresses the issues of realistic specific energy levels attainable with Li batteries, the maximum number of electric vehicles as limited by the identified Li world reserves and the anticipated battery price. The Li-ion battery, {LiC6}/{LixNiO2}, is taken as the basis for the analysis presented here. It is shown that economically recoverable Li world reserves are sufficient to meet the demands of current new passenger car world production and its anticipated growth in the next 50 years. Currently identified world reserves can power 2 billion cars with Li-ion batteries, that is four times the number of cars presently registered in the world. World annual Li production of 10 000 metric tons would have to be increased l3-fold to power current new car world production with Li batteries. Such increase of the production capacity is seen as principally feasible. The 'theoretical reactant cost' — the absolute minimum reactant cost — for the Li-ion battery with Ni oxide cathode is US 19.20/kWh, compared to US 15.40 for the {Ni}/{Cd} and US 29.40 for the Ni/metal-hydride (AB 2) battery. By comparison with the large-volume price for {Ni}/{Cd} vehicle batteries, a miniμm price of US 330/kWh or US 8000 per 24 kWh battery is predicted for mass-produced Li-ion vehicle batteries, once the technology has matured. A battery life of 1000 cycles, already demonstrated in laboratory cells, results in a total vehicle mileage of approximately 126 000 miles when based on a 24 kWh battery. The cost of battery ownership and 'electric fuel' combined is 11 ¢/mile, that of car ownership and fuel combined 27 ¢/toile, if based on a vehicle price of US 23 000.

  17. Electrical circuit models for performance modeling of Lithium-Sulfur batteries

    DEFF Research Database (Denmark)

    Knap, Vaclav; Stroe, Daniel Ioan; Teodorescu, Remus;

    2015-01-01

    Energy storage technologies such as Lithium-ion (Li-ion) batteries are widely used in the present effort to move towards more ecological solutions in sectors like transportation or renewable-energy integration. However, today's Li-ion batteries are reaching their limits and not all demands...... emerging technology for various applications, there is a need for Li-S battery performance model; however, developing such models represents a challenging task due to batteries' complex ongoing chemical reactions. Therefore, the literature review was performed to summarize electrical circuit models (ECMs...

  18. Smart battery management systems: towards an efficient integration of electrical energy storage in smart regions

    OpenAIRE

    Gano, A. J.; Silva, Hugo M.; Correia, João Bernardino; Martins, Maria João

    2013-01-01

    Electrical energy storage systems for electric vehicles or stationary applications will be important actors in Smart Region's energy scenarios, strongly contributing to increase the efficient and sustainable use of available resources. However, massive integration of such systems stillposes many problems, requiring enhancements in batteries's life time, autonomy, reliability and cost. The development of new smart and accurate battery management systems able to communicate with a broad range o...

  19. An economic analysis of used electric vehicle batteries integrated into commercial building microgrids

    OpenAIRE

    Beer, Sebastian; Gómez, Tomás; Dallinger, David; Momber, Ilan; Marnay, Chris

    2011-01-01

    Current policies in the U.S. and other countries are trying to stimulate electric transportation deployment. Consequently, plug-in electric vehicle (PEV) adoption will presumably spread among vehicle users. With the increased diffusion of PEVs, lithium-ion batteries will also enter the market on a broad scale. However, their costs are still high and ways are needed to optimally deploy vehicle batteries in order to account for the higher initial outlay. This study analyzed the possibility of e...

  20. New Electro-Thermal Battery Pack Model of an Electric Vehicle

    Directory of Open Access Journals (Sweden)

    Muhammed Alhanouti

    2016-07-01

    Full Text Available Since the evolution of the electric and hybrid vehicle, the analysis of batteries’ characteristics and influence on driving range has become essential. This fact advocates the necessity of accurate simulation modeling for batteries. Different models for the Li-ion battery cell are reviewed in this paper and a group of the highly dynamic models is selected for comparison. A new open circuit voltage (OCV model is proposed. The new model can simulate the OCV curves of lithium iron magnesium phosphate (LiFeMgPO4 battery type at different temperatures. It also considers both charging and discharging cases. The most remarkable features from different models, in addition to the proposed OCV model, are integrated in a single hybrid electrical model. A lumped thermal model is implemented to simulate the temperature development in the battery cell. The synthesized electro-thermal battery cell model is extended to model a battery pack of an actual electric vehicle. Experimental tests on the battery, as well as drive tests on the vehicle are performed. The proposed model demonstrates a higher modeling accuracy, for the battery pack voltage, than the constituent models under extreme maneuver drive tests.

  1. Electro-thermal analysis and integration issues of lithium ion battery for electric vehicles

    International Nuclear Information System (INIS)

    Highlights: • We modeled the electrical and thermal behavior of the Li-ion battery. • We validated the simulation results with experimental studies. • We compared the thermal performance of different size of cylindrical cells. • We investigated the integration issues of cylindrical cells into battery pack. - Abstract: Electrical and thermal characteristics of lithium-ion battery packs in electric vehicles in different operating conditions are important in order to design the battery pack thermal management system. In this work, electrical and thermal behaviors of different size of LiFePO4 cylindrical cells are investigated under various operating conditions. The simulation results show good agreement with the experimental data under various operating modes. Due to the large thermal resistance of layered active material in a Li-ion cell, the temperature difference in the radial direction is significantly correlated with a diameter of cell and It-rates. Compared with natural convection, strong forced convection will reduce the temperature uniformity in the cell and accelerate the thermal aging rate. Lastly, integration issues of the cells into a battery pack are discussed from mechanical, electrical, thermal, control and monitoring, manufacturing and maintenance aspects. These issues could impact the performance, cost, driving range and life cycle of the battery pack in electric vehicles

  2. Electric vehicle battery charging algorithm using PMSM windings and an inverter as an active rectifier

    DEFF Research Database (Denmark)

    Zaja, Mario; Oprea, Matei-lon; Suárez, Carlos Gómez;

    2014-01-01

    the battery gets discharged below the peak of the grid voltage, typically if the vehicle has not been used for a longer period of time. To avoid high currents that could damage the battery, a voltage suppression mode is introduced for safe depleted battery charging. This paper proposes and analyzes......A major setback for large scale electric vehicle market expansion compared to their internal combustion competitors consists in their high price and low driving range. One way of reducing the cost, dimensions and mass of electric vehicles is to eliminate the dedicated AC/DC converter used...

  3. A new battery capacity indicator for lithium-ion battery powered electric vehicles using adaptive neuro-fuzzy inference system

    Energy Technology Data Exchange (ETDEWEB)

    Chau, K.T.; Wu, K.C.; Chan, C.C. [University of Hong Kong (China). Dept. of Electrical and Electronic Engineering

    2004-07-01

    This paper describes a new adaptive neuro-fuzzy inference system (ANFIS) model to estimate accurately the battery residual capacity (BRC) of the lithium-ion (Li-ion) battery for modern electric vehicles (EVs). The key to this model is to adopt newly both the discharged/regenerative capacity distributions and the temperature distributions as the inputs and the state of available capacity (SOAC) as the output, which represents the BRC. Moreover, realistic EV discharge current profiles are newly used to formulate the proposed model. The accuracy of the estimated SOAC obtained from the model is verified by experiments under various EV discharge current profiles. (author)

  4. Current Situation and Development Trend of Standards of Lithium Batteries for Electric Vehides

    Institute of Scientific and Technical Information of China (English)

    Meng Xiangfeng; Wen Baozhong

    2012-01-01

    Traction battery is one of the most significant systems in electric vehicles.Its general performance,cycle characteristics and safety performance have crucial influence on the economical efficiency,dynamic property and safety of the vehicle.Therefore traction battery has always been the key area in researches of electric vehicles and its standardization. 1.Main performance indicators of traction batteries As the energy storage device of electric vehicles,the performance of traction battery is very important for the complete vehicle.Requirements of traction battery for electric vehicles should have the following characteristics as high power,high energy,high energy density/specific energy,high power density/specific power,low cost,long life length,abuse resistance,high reliability,good temperature property,short charging time,nice interchangeability etc.Traction batteries used at present are mainly lead-acid cells,nickel-hydride cells and lithium-ion cells.Although none of them can meet all requirements,lithium battery is widely regarded the most promising one with optimal comprehensive performance in recent time.

  5. Teaching Electric Circuits with Multiple Batteries: A Qualitative Approach

    Science.gov (United States)

    Smith, David P.; van Kampen, Paul

    2011-01-01

    We have investigated preservice science teachers' qualitative understanding of circuits consisting of multiple batteries in single and multiple loops using a pretest and post-test method and classroom observations. We found that most students were unable to explain the effects of adding batteries in single and multiple loops, as they tended to use…

  6. Sodium sulfur electric vehicle battery engineering program final report, September 2, 1986--June 15, 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-06-01

    In September 1986 a contract was signed between Chloride Silent Power Limited (CSPL) and Sandia National Laboratories (SNL) entitled ``Sodium Sulfur Electric Vehicle Battery Engineering Program``. The aim of the cost shared program was to advance the state of the art of sodium sulfur batteries for electric vehicle propulsion. Initially, the work statement was non-specific in regard to the vehicle to be used as the design and test platform. Under a separate contract with the DOE, Ford Motor Company was designing an advanced electric vehicle drive system. This program, called the ETX II, used a modified Aerostar van for its platform. In 1987, the ETX II vehicle was adopted for the purposes of this contract. This report details the development and testing of a series of battery designs and concepts which led to the testing, in the US, of three substantial battery deliverables.

  7. Critical review of on-board capacity estimation techniques for lithium-ion batteries in electric and hybrid electric vehicles

    Science.gov (United States)

    Farmann, Alexander; Waag, Wladislaw; Marongiu, Andrea; Sauer, Dirk Uwe

    2015-05-01

    This work provides an overview of available methods and algorithms for on-board capacity estimation of lithium-ion batteries. An accurate state estimation for battery management systems in electric vehicles and hybrid electric vehicles is becoming more essential due to the increasing attention paid to safety and lifetime issues. Different approaches for the estimation of State-of-Charge, State-of-Health and State-of-Function are discussed and analyzed by many authors and researchers in the past. On-board estimation of capacity in large lithium-ion battery packs is definitely one of the most crucial challenges of battery monitoring in the aforementioned vehicles. This is mostly due to high dynamic operation and conditions far from those used in laboratory environments as well as the large variation in aging behavior of each cell in the battery pack. Accurate capacity estimation allows an accurate driving range prediction and accurate calculation of a battery's maximum energy storage capability in a vehicle. At the same time it acts as an indicator for battery State-of-Health and Remaining Useful Lifetime estimation.

  8. Environmental impact analysis of electric and hybrid vehicle batteries. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-16

    This environmental impact analysis of electric and hybrid vehicle batteries is intended to identify principal environmental impacts resulting directly or indirectly from the development of electric vehicle batteries. Thus, the result of this study could be used to determine the appropriate following step in the U.S. DOE's EIA process. The environmental impacts considered in this document are the incremental impacts generated during the various phases in the battery life cycle. The processes investigated include mining, milling, smelting, and refining of metallic materials for electrode components; manufacturing processes of inorganic chemicals and other materials for electrolytes and other hardware components; battery assembly processes; operation and maintenance of batteries; and recycling and disposal of used batteries. The severity of the incremental impacts is quantified to the extent consistent with the state-of-knowledge. Many of the industrial processes involve proprietary or patent information; thus, in many cases, the associated environmental impacts could not be determined. In addition, most candidate battery systems are still in the development phase. Thus, the manufacturing and recycling processes for most battery systems either have not been developed by industry, or the information is not available. For these cases, the associated environmental impact evaluations could only be qualitative, and the need for further investigations is indicated. 26 figures, 27 tables. (RWR)

  9. Geometric-Process-Based Battery Management Optimizing Policy for the Electric Bus

    Directory of Open Access Journals (Sweden)

    Yan Li

    2015-01-01

    Full Text Available With the rapid development of the electric vehicle industry and promotive policies worldwide, the electric bus (E-bus has been adopted in many major cities around the world. One of the most important factors that restrain the widespread application of the E-bus is the high operating cost due to the deficient battery management. This paper proposes a geometric-process-based (GP-based battery management optimizing policy which aims to minimize the average cost of the operation on the premise of meeting the required sufficient battery availability. Considering the deterioration of the battery after repeated charging and discharging, this paper constructs the model of the operation of the E-bus battery as a geometric process, and the premaintenance time has been considered with the failure repairment time to enhance the GP-based battery operation model considering the battery cannot be as good as new after the two processes. The computer simulation is carried out by adopting the proposed optimizing policy, and the result verifies the effectiveness of the policy, denoting its significant performance on the application of the E-bus battery management.

  10. eRoads: A comparison between oil, battery electric vehicles, and electric roads for Danish road transport in terms of energy, emissions, and costs

    DEFF Research Database (Denmark)

    Connolly, David

    2016-01-01

    This study compares electric roads with oil (petrol and diesel) and battery electric vehicles, using Denmark as a case study. Electric roads can reduce the cost of electric vehicles by supplying them with electricity directly from the road rather than via a battery for long-distance journeys....... In this paper, an electric road scenario is compared to both an oil and battery electric vehicle scenario using the 2010 Danish energy system, but for two sets of costs: one set based on historical costs from the year 2010 and one based on projected costs for the year 2050. The results indicate that electric...... roads are more expensive than oil today, but they will be cheaper than oil in 2050. Furthermore, electric roads are cheaper than Battery Electric Vehicles in all of the scenarios considered here, which indicates that the upfront investment required to build the electric roads is less than the additional...

  11. A chemistry and material perspective on lithium redox flow batteries towards high-density electrical energy storage.

    Science.gov (United States)

    Zhao, Yu; Ding, Yu; Li, Yutao; Peng, Lele; Byon, Hye Ryung; Goodenough, John B; Yu, Guihua

    2015-11-21

    Electrical energy storage system such as secondary batteries is the principle power source for portable electronics, electric vehicles and stationary energy storage. As an emerging battery technology, Li-redox flow batteries inherit the advantageous features of modular design of conventional redox flow batteries and high voltage and energy efficiency of Li-ion batteries, showing great promise as efficient electrical energy storage system in transportation, commercial, and residential applications. The chemistry of lithium redox flow batteries with aqueous or non-aqueous electrolyte enables widened electrochemical potential window thus may provide much greater energy density and efficiency than conventional redox flow batteries based on proton chemistry. This Review summarizes the design rationale, fundamentals and characterization of Li-redox flow batteries from a chemistry and material perspective, with particular emphasis on the new chemistries and materials. The latest advances and associated challenges/opportunities are comprehensively discussed.

  12. A chemistry and material perspective on lithium redox flow batteries towards high-density electrical energy storage.

    Science.gov (United States)

    Zhao, Yu; Ding, Yu; Li, Yutao; Peng, Lele; Byon, Hye Ryung; Goodenough, John B; Yu, Guihua

    2015-11-21

    Electrical energy storage system such as secondary batteries is the principle power source for portable electronics, electric vehicles and stationary energy storage. As an emerging battery technology, Li-redox flow batteries inherit the advantageous features of modular design of conventional redox flow batteries and high voltage and energy efficiency of Li-ion batteries, showing great promise as efficient electrical energy storage system in transportation, commercial, and residential applications. The chemistry of lithium redox flow batteries with aqueous or non-aqueous electrolyte enables widened electrochemical potential window thus may provide much greater energy density and efficiency than conventional redox flow batteries based on proton chemistry. This Review summarizes the design rationale, fundamentals and characterization of Li-redox flow batteries from a chemistry and material perspective, with particular emphasis on the new chemistries and materials. The latest advances and associated challenges/opportunities are comprehensively discussed. PMID:26265165

  13. Policy driven demand for sales of plug-in hybrid electric vehicles and battery-electric vehicles in Germany

    OpenAIRE

    Trommer, Stefan; Kihm, Alexander; Hebes, Paul; Mehlin, Markus

    2010-01-01

    While technology issues are increasingly overcoming, the economic viability of electric vehicles is remaining constrained by higher prices than for conventional vehicles. However, first automakers present their Battery Electric Vehicles (BEVs) and Plug-in Hybrid Electric Vehicles (PHEV) or at least pronounce them for the near future. Hence, there is an emerging need for vehicle manufacturers, practitioners and policy to estimate the particular demand for partly and fully electrified drive tr...

  14. Optimal management of stationary lithium-ion battery system in electricity distribution grids

    Science.gov (United States)

    Purvins, Arturs; Sumner, Mark

    2013-11-01

    The present article proposes an optimal battery system management model in distribution grids for stationary applications. The main purpose of the management model is to maximise the utilisation of distributed renewable energy resources in distribution grids, preventing situations of reverse power flow in the distribution transformer. Secondly, battery management ensures efficient battery utilisation: charging at off-peak prices and discharging at peak prices when possible. This gives the battery system a shorter payback time. Management of the system requires predictions of residual distribution grid demand (i.e. demand minus renewable energy generation) and electricity price curves (e.g. for 24 h in advance). Results of a hypothetical study in Great Britain in 2020 show that the battery can contribute significantly to storing renewable energy surplus in distribution grids while being highly utilised. In a distribution grid with 25 households and an installed 8.9 kW wind turbine, a battery system with rated power of 8.9 kW and battery capacity of 100 kWh can store 7 MWh of 8 MWh wind energy surplus annually. Annual battery utilisation reaches 235 cycles in per unit values, where one unit is a full charge-depleting cycle depth of a new battery (80% of 100 kWh).

  15. 46 CFR 31.35-1 - Electrical installations, lighting and power equipment, batteries, etc.-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Electrical installations, lighting and power equipment, batteries, etc.-TB/ALL. 31.35-1 Section 31.35-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS INSPECTION AND CERTIFICATION Electrical Engineering § 31.35-1 Electrical installations, lighting and power equipment, batteries,...

  16. Response of lead-acid batteries to chopper-controlled discharge. [for electric vehicles

    Science.gov (United States)

    Cataldo, R. L.

    1978-01-01

    The results of tests on an electric vehicle battery, using a simulated electric vehicle chopper-speed controller, show energy output losses up to 25 percent compared to constant current discharges at the same average current of 100 A. However, an energy output increase of 22 percent is noticed at the 200 A average level and 44 percent increase at the 300 A level using pulse discharging. Because of these complex results, electric vehicle battery/speed controller interactions must be considered in vehicle design.

  17. Specific systems studies of battery energy storage for electric utilities

    Energy Technology Data Exchange (ETDEWEB)

    Akhil, A.A.; Lachenmeyer, L. [Sandia National Labs., Albuquerque, NM (United States); Jabbour, S.J. [Decision Focus, Inc., Mountain View, CA (United States); Clark, H.K. [Power Technologies, Inc., Roseville, CA (United States)

    1993-08-01

    Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Energy Management. As a part of this program, four utility-specific systems studies were conducted to identify potential battery energy storage applications within each utility network and estimate the related benefits. This report contains the results of these systems studies.

  18. Demand Profile Study of Battery Electric Vehicle under Different Charging Options

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guang Ya; Træholt, Chresten;

    2012-01-01

    An increased research on electric vehicles (EV) and plug-in hybrid electric vehicles (PHEV) deals with their flexible use in electric power grids. Several research projects on smart grids and electric mobility are now looking into realistic models representing the behavior of an EV during charging......, including nonlinearities. In this work, modeling, simulation and testing of the demand profile of a battery-EV are conducted. Realistic work conditions for a lithium-ion EV battery and battery charger are considered as the base for the modeling. Simulation results show that EV charging generates different...... demand profiles into the grid, depending on the applied charging option. Moreover, a linear region for the control of EV chargers is identified in the range of 20-90% state-of-charge (SOC). Experiments validate the proposed model....

  19. A LiFePO4 battery pack capacity estimation approach considering in-parallel cell safety in electric vehicles

    International Nuclear Information System (INIS)

    Highlights: • Find the influence of in-parallel battery cell variations on battery pack capacity. • Redefine the battery module capacity with considering ANY battery cell safety. • Discuss the safety end-of-charge voltage for an aged in-parallel battery module. • Build an algorithm for battery pack capacity estimation with the charge curve. • Bench tests are used to verify the validity of the proposed algorithm. - Abstract: In electric vehicles (EVs), several battery cells are connected in parallel to establish a battery module. The safety of the battery module is influenced by inconsistent battery cell performance which causes uneven currents flowing through internal in-parallel battery cells. A battery cell model is developed based on the Matlab–Simscape platform and validated by tests. The battery cell model is used to construct simulation models for analyzing the effect of battery cell inconsistency on the performance of an in-parallel battery module. Simulation results indicate that the state-of-charge (SOC) of a battery module cannot characterize the SOC of ALL the internal battery cells in the battery module. When the battery management system (BMS) controls the end-of-charge (EOC) time according to the SOC of a battery module, some internal battery cells are over-charged. To guarantee the safety of ALL battery cells through the whole battery life, a safety EOC voltage of the battery module should be set according to the number of battery cells in the battery module and the applied charge current. Simulations reveal that the SOC of the “normal battery module” is related to its charge voltage when aged battery module is charged to the EOC voltage. Then, a function describing their relationship is established. Both the capacity and the charge voltage shift are estimated by comparing the measured voltage-to-capacity curve with the standard one provided by the manufactory. A battery pack capacity estimation method is proposed according to the SOC

  20. Research, development, and demonstration of lead-acid batteries for electric vehicle propulsion. Annual report, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    The initial phase of work comprises three factorial experiments to evaluate a variety of component combinations. Goals to be met by these batteries include the following: capacity at 3 h discharge, 20 to 30 kWh; specific energy, 40 Wh/kg; specific power, 1000 W/kg for 15 s; cycle life, 800 cycles to 80% depth; price, $50/kWh. The status of the factorial experiments is reviewed. The second phase of work, design of an advanced battery, has the following goals: 30 to 40 kWh; 60 Wh/kg; 150 W/kg for 15 s; 1000 cycles to 80% depth; $40/kWh. It is not yet possible to say whether these goals can be met. Numerous approaches are under study to increase the utilization of battery chemicals. A battery design with no live electrical connection above the battery is being developed. 52 figures, 52 tables. (RWR)

  1. Prediction Model of Battery State of Charge and Control Parameter Optimization for Electric Vehicle

    Directory of Open Access Journals (Sweden)

    Bambang Wahono

    2015-07-01

    Full Text Available This paper presents the construction of a battery state of charge (SOC prediction model and the optimization method of the said model to appropriately control the number of parameters in compliance with the SOC as the battery output objectives. Research Centre for Electrical Power and Mechatronics, Indonesian Institute of Sciences has tested its electric vehicle research prototype on the road, monitoring its voltage, current, temperature, time, vehicle velocity, motor speed, and SOC during the operation. Using this experimental data, the prediction model of battery SOC was built. Stepwise method considering multicollinearity was able to efficiently develops the battery prediction model that describes the multiple control parameters in relation to the characteristic values such as SOC. It was demonstrated that particle swarm optimization (PSO succesfully and efficiently calculated optimal control parameters to optimize evaluation item such as SOC based on the model.

  2. Project Milestone. Analysis of Range Extension Techniques for Battery Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Neubauer, Jeremy [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wood, Eric [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Pesaran, Ahmad [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2013-07-01

    This report documents completion of the July 2013 milestone as part of NREL’s Vehicle Technologies Annual Operating Plan with the U.S. Department of Energy. The objective was to perform analysis on range extension techniques for battery electric vehicles (BEVs). This work represents a significant advancement over previous thru-life BEV analyses using NREL’s Battery Ownership Model, FastSim,* and DRIVE.* Herein, the ability of different charging infrastructure to increase achievable travel of BEVs in response to real-world, year-long travel histories is assessed. Effects of battery and cabin thermal response to local climate, battery degradation, and vehicle auxiliary loads are captured. The results reveal the conditions under which different public infrastructure options are most effective, and encourage continued study of fast charging and electric roadway scenarios.

  3. An overview of the development of lead/acid traction batteries for electric vehicles in India

    Science.gov (United States)

    Sivaramaiah, G.; Subramanian, V. R.

    Electric vehicles (EVs) made an entry into the Indian scene quite recently in the area of passenger transportation, milk floats and other similar applications. The industrial EV market, with various models of fork-lift trucks and platform trucks already in wide use all over India, is a better understood application of EV batteries. The lead/acid traction batteries available in India are not of high-energy density. The best available indigenous lead/acid traction battery has an energy density ( C/5 rate) of 30 W h kg -1 as against 39 W h kg -1 available abroad. This paper reviews the developmental efforts relating to lead/acid traction batteries for electric vehicle applications in India, such as prototype road vehicles, commercial vehicles, rail cars, and locomotives. Due to the need for environmental protection and recognition of exhaustible, finite supplies of petroleum fuel, the Indian government is presently taking active interest in EV projects.

  4. Progress of the Computer-Aided Engineering of Electric Drive Vehicle Batteries (CAEBAT) (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Pesaran, A. A.; Han, T.; Hartridge, S.; Shaffer, C.; Kim, G. H.; Pannala, S.

    2013-06-01

    This presentation, Progress of Computer-Aided Engineering of Electric Drive Vehicle Batteries (CAEBAT) is about simulation and computer-aided engineering (CAE) tools that are widely used to speed up the research and development cycle and reduce the number of build-and-break steps, particularly in the automotive industry. Realizing this, DOE?s Vehicle Technologies Program initiated the CAEBAT project in April 2010 to develop a suite of software tools for designing batteries.

  5. Energy Consumption of a Battery Electric Vehicle with Infinitely Variable Transmission

    OpenAIRE

    Francesco Bottiglione; Stefano De Pinto; Giacomo Mantriota; Aldo Sorniotti

    2014-01-01

    Battery electric vehicles (BEVs) represent a possible sustainable solution for personal urban transportation. Presently, the most limiting characteristic of BEVs is their short range, mainly because of battery technology limitations. A proper design and control of the drivetrain, aimed at reducing the power losses and thus increasing BEV range, can contribute to make the electrification of urban transportation a convenient choice. This paper presents a simulation-based comparison of the energ...

  6. Development of Novel Bipolar Nickel/Metal Hydride Batteries for Hybrid Electric Vehicles

    Institute of Scientific and Technical Information of China (English)

    邓超; 史鹏飞; 张森

    2005-01-01

    This paper deals with the design and development of bipolar Ni/MH batteries. After optimizing the parameters of bipolar plates by adjusting electrode thickness and modifying the capacity ratio of two adjacent electrodes of a single cell, some bipolar Ni/MH stacks with a voltage of 6 V were assembled and examined. Electrochemical testing results showed that the bipolar battery has excellent high rate discharge and recharge characteristics, satisfying pulse discharge performance even in a low state of charge (SOC). Moreover, the battery showed good stability during pulse cycles as simulating hybrid electric vehicle working conditions. It would be a promising alternative for power storage system in hybrid electxic vehicles.

  7. Feasibility study for the recycling of nickel metal hydride electric vehicle batteries. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sabatini, J.C.; Field, E.L.; Wu, I.C.; Cox, M.R.; Barnett, B.M.; Coleman, J.T. [Little (Arthur D.), Inc., Cambridge, MA (United States)

    1994-01-01

    This feasibility study examined three possible recycling processes for two compositions (AB{sub 2} and AB{sub 5}) of nickel metal hydride electric vehicle batteries to determine possible rotes for recovering battery materials. Analysts examined the processes, estimated the costs for capital equipment and operation, and estimated the value of the reclaimed material. They examined the following three processes: (1) a chemical process that leached battery powders using hydrochloric acid, (2) a pyrometallurical process, and (3) a physical separation/chemical process. The economic analysis revealed that the physical separation/chemical process generated the most revenue.

  8. Applications of aluminum hybrid foam sandwiches in battery housings for electric vehicles

    OpenAIRE

    Baumeister, J; Weise, J; Hirtz, E.; Höhne, K; Hohe, J.

    2014-01-01

    Battery packs for purely electrical driven vehicles should allow for a long driving range, therefore they must be as light as possible. The aim of the project “SmartBatt” – funded by the EC under the 7th Framework Programme – was to create a 20 kWh battery pack which exhibits a 10-15% weight reduction as compared to the State of the Art. This was accomplished by using innovative sandwich materials made of aluminum face sheets and a core of aluminum hybrid foam for the battery housing. Aluminu...

  9. Electric Ground Support Equipment Advanced Battery Technology Demonstration Project at the Ontario Airport

    Energy Technology Data Exchange (ETDEWEB)

    Tyler Gray; Jeremy Diez; Jeffrey Wishart; James Francfort

    2013-07-01

    The intent of the electric Ground Support Equipment (eGSE) demonstration is to evaluate the day-to-day vehicle performance of electric baggage tractors using two advanced battery technologies to demonstrate possible replacements for the flooded lead-acid (FLA) batteries utilized throughout the industry. These advanced battery technologies have the potential to resolve barriers to the widespread adoption of eGSE deployment. Validation testing had not previously been performed within fleet operations to determine if the performance of current advanced batteries is sufficient to withstand the duty cycle of electric baggage tractors. This report summarizes the work performed and data accumulated during this demonstration in an effort to validate the capabilities of advanced battery technologies. This report summarizes the work performed and data accumulated during this demonstration in an effort to validate the capabilities of advanced battery technologies. The demonstration project also grew the relationship with Southwest Airlines (SWA), our demonstration partner at Ontario International Airport (ONT), located in Ontario, California. The results of this study have encouraged a proposal for a future demonstration project with SWA.

  10. Current status of environmental, health, and safety issues of nickel metal-hydride batteries for electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Corbus, D; Hammel, C J; Mark, J

    1993-08-01

    This report identifies important environment, health, and safety issues associated with nickel metal-hydride (Ni-MH) batteries and assesses the need for further testing and analysis. Among the issues discussed are cell and battery safety, workplace health and safety, shipping requirements, and in-vehicle safety. The manufacture and recycling of Ni-MH batteries are also examined. This report also overviews the ``FH&S`` issues associated with other nickel-based electric vehicle batteries; it examines venting characteristics, toxicity of battery materials, and the status of spent batteries as a hazardous waste.

  11. Current status of environmental, health, and safety issues of nickel metal-hydride batteries for electric vehicles

    International Nuclear Information System (INIS)

    This report identifies important environment, health, and safety issues associated with nickel metal-hydride (Ni-MH) batteries and assesses the need for further testing and analysis. Among the issues discussed are cell and battery safety, workplace health and safety, shipping requirements, and in-vehicle safety. The manufacture and recycling of Ni-MH batteries are also examined. This report also overviews the ''FH ampersand S'' issues associated with other nickel-based electric vehicle batteries; it examines venting characteristics, toxicity of battery materials, and the status of spent batteries as a hazardous waste

  12. Analysis of Lithium-Ion Battery Data Collected  On-Board Electric Vehicles

    OpenAIRE

    Peng, Lin

    2013-01-01

    In order to replace diesel energy in the transportation sector as well as to reduce the emission of green house gases (GHGs) and avoid air pollution for a sustainable future, electrification of vehicles is one of the most popular topics today. Plug-in hybrid electric vehicle (PHEV) technology is a promising technology for electrification of automobiles. It uses both internal combustion engine and electric motor for propulsion. The battery pack that propels the electric machine can be recharge...

  13. A Multiphase Traction/Fast-Battery-Charger Drive for Electric or Plug-in Hybrid Vehicles

    OpenAIRE

    Sandulescu, Paul; KESTELYN, Xavier; SEMAIL, Eric; BRUYERE, Antoine; Bouchez, Boris; Sousa, Luis

    2010-01-01

    For Electric Vehicles (EV), the charger is one of the main technical and economical weaknesses. This paper focuses on an original electric drive [1]-[3] dedicated to the vehicle traction and configurable as a battery charger without need of additional components. This cheap solution can outfit either electric or plug-in hybrid automotive vehicles, without needing additional mass and volume dedicated to the charger. Moreover, it allows a high charging power, for short duration charge cycles. H...

  14. Review and recent advances in battery health monitoring and prognostics technologies for electric vehicle (EV) safety and mobility

    Science.gov (United States)

    Rezvanizaniani, Seyed Mohammad; Liu, Zongchang; Chen, Yan; Lee, Jay

    2014-06-01

    As hybrid and electric vehicle technologies continue to advance, car manufacturers have begun to employ lithium ion batteries as the electrical energy storage device of choice for use in existing and future vehicles. However, to ensure batteries are reliable, efficient, and capable of delivering power and energy when required, an accurate determination of battery performance, health, and life prediction is necessary. This paper provides a review of battery prognostics and health management (PHM) techniques, with a focus on major unmet needs in this area for battery manufacturers, car designers, and electric vehicle drivers. A number of approaches are presented that have been developed to monitor battery health status and performance, as well as the evolution of prognostics modeling methods. The goal of this review is to render feasible and cost effective solutions for dealing with battery life issues under dynamic operating conditions.

  15. Towards greener and more sustainable batteries for electrical energy storage.

    Science.gov (United States)

    Larcher, D; Tarascon, J-M

    2015-01-01

    Ever-growing energy needs and depleting fossil-fuel resources demand the pursuit of sustainable energy alternatives, including both renewable energy sources and sustainable storage technologies. It is therefore essential to incorporate material abundance, eco-efficient synthetic processes and life-cycle analysis into the design of new electrochemical storage systems. At present, a few existing technologies address these issues, but in each case, fundamental and technological hurdles remain to be overcome. Here we provide an overview of the current state of energy storage from a sustainability perspective. We introduce the notion of sustainability through discussion of the energy and environmental costs of state-of-the-art lithium-ion batteries, considering elemental abundance, toxicity, synthetic methods and scalability. With the same themes in mind, we also highlight current and future electrochemical storage systems beyond lithium-ion batteries. The complexity and importance of recycling battery materials is also discussed. PMID:25515886

  16. Towards greener and more sustainable batteries for electrical energy storage.

    Science.gov (United States)

    Larcher, D; Tarascon, J-M

    2015-01-01

    Ever-growing energy needs and depleting fossil-fuel resources demand the pursuit of sustainable energy alternatives, including both renewable energy sources and sustainable storage technologies. It is therefore essential to incorporate material abundance, eco-efficient synthetic processes and life-cycle analysis into the design of new electrochemical storage systems. At present, a few existing technologies address these issues, but in each case, fundamental and technological hurdles remain to be overcome. Here we provide an overview of the current state of energy storage from a sustainability perspective. We introduce the notion of sustainability through discussion of the energy and environmental costs of state-of-the-art lithium-ion batteries, considering elemental abundance, toxicity, synthetic methods and scalability. With the same themes in mind, we also highlight current and future electrochemical storage systems beyond lithium-ion batteries. The complexity and importance of recycling battery materials is also discussed.

  17. Towards greener and more sustainable batteries for electrical energy storage

    Science.gov (United States)

    Larcher, D.; Tarascon, J.-M.

    2015-01-01

    Ever-growing energy needs and depleting fossil-fuel resources demand the pursuit of sustainable energy alternatives, including both renewable energy sources and sustainable storage technologies. It is therefore essential to incorporate material abundance, eco-efficient synthetic processes and life-cycle analysis into the design of new electrochemical storage systems. At present, a few existing technologies address these issues, but in each case, fundamental and technological hurdles remain to be overcome. Here we provide an overview of the current state of energy storage from a sustainability perspective. We introduce the notion of sustainability through discussion of the energy and environmental costs of state-of-the-art lithium-ion batteries, considering elemental abundance, toxicity, synthetic methods and scalability. With the same themes in mind, we also highlight current and future electrochemical storage systems beyond lithium-ion batteries. The complexity and importance of recycling battery materials is also discussed.

  18. Thermoelectric Modeling and Online SOC Estimation of Li-Ion Battery for Plug-In Hybrid Electric Vehicles

    OpenAIRE

    Aishwarya Panday; Hari Om Bansal; Pramod Srinivasan

    2016-01-01

    The increasing oil price, energy demand, and environmental concern are leading to a global switch towards Plug-In Hybrid Electric Vehicles (PHEVs). In a PHEV, Li-ion battery is considered as the primary propelling source. Therefore, an accurate battery model is required to predict the I-V characteristic and dynamic behavior of a battery. This paper presents a highly effective thermoelectric model of Li-ion battery developed in Simulink. An algorithm is proposed for estimation of state of char...

  19. A win-win marginal rent analysis for operator and consumer under battery leasing mode in China electric vehicle market

    Energy Technology Data Exchange (ETDEWEB)

    Li Zhe, E-mail: lizhe1212@gmail.com [State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing 100084 (China); Ouyang Minggao, E-mail: ouymg@tsinghua.edu.cn [State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing 100084 (China)

    2011-06-15

    Recently battery leasing has been introduced into the market by automobile manufacturers and power suppliers due to its potential to reduce the purchase cost of electric vehicles (EVs). However, the profit prospect of battery leasing is still uncertain. This paper takes the views of both the operators and consumers and calculates the 'win-win' marginal rent, which not only ensures the profitability of operators, but also allows consumers a lower expenditure than using Internal combustion engine vehicles (ICVs) and EVs with embedded batteries. Battery cost, vehicle weight, gasoline and electricity price, and the discount rate have impacts on the rent. Battery cost plays a dominant role and a battery cost >5 Yen /W h fails to enable the survival of battery leasing to all types of EVs. Battery leasing would be more competitive when focusing on heavier EVs. At least one of the three thresholds is required for the existence of rent pricing range for a 1000 kg EV: gasoline retail price >6 Yen /L, electricity price <0.6 Yen /kW h, or the discount rate <7%. Typically, the feasible battery rent range is 0.34-0.38 Yen /W h/year for a 1000 kg EV under the present battery cost 2 Yen /W h and China current gasoline and electricity prices. - Highlights: > Rent pricing for EV battery leasing must obey win-win rule for BLO and consumers. > Rent is affected by battery cost, vehicle weight, energy price and discount rate. > Battery cost plays dominant role for the BLO survival as described in '5-3-2' Law. > Heavier EVs are more suitable for battery leasing when battery cost is high. > The profitability of BLO is sensitive to the price of gasoline and electricity.

  20. A win-win marginal rent analysis for operator and consumer under battery leasing mode in China electric vehicle market

    International Nuclear Information System (INIS)

    Recently battery leasing has been introduced into the market by automobile manufacturers and power suppliers due to its potential to reduce the purchase cost of electric vehicles (EVs). However, the profit prospect of battery leasing is still uncertain. This paper takes the views of both the operators and consumers and calculates the 'win-win' marginal rent, which not only ensures the profitability of operators, but also allows consumers a lower expenditure than using Internal combustion engine vehicles (ICVs) and EVs with embedded batteries. Battery cost, vehicle weight, gasoline and electricity price, and the discount rate have impacts on the rent. Battery cost plays a dominant role and a battery cost >5 Yen /W h fails to enable the survival of battery leasing to all types of EVs. Battery leasing would be more competitive when focusing on heavier EVs. At least one of the three thresholds is required for the existence of rent pricing range for a 1000 kg EV: gasoline retail price >6 Yen /L, electricity price <0.6 Yen /kW h, or the discount rate <7%. Typically, the feasible battery rent range is 0.34-0.38 Yen /W h/year for a 1000 kg EV under the present battery cost 2 Yen /W h and China current gasoline and electricity prices. - Highlights: → Rent pricing for EV battery leasing must obey win-win rule for BLO and consumers. → Rent is affected by battery cost, vehicle weight, energy price and discount rate. → Battery cost plays dominant role for the BLO survival as described in '5-3-2' Law. → Heavier EVs are more suitable for battery leasing when battery cost is high. → The profitability of BLO is sensitive to the price of gasoline and electricity.

  1. Online Identification of Power Required for Self-Sustainability of the Battery in Hybrid Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Malikopoulos, Andreas [ORNL

    2014-01-01

    Hybrid electric vehicles have shown great potential for enhancing fuel economy and reducing emissions. Deriving a power management control policy to distribute the power demanded by the driver optimally to the available subsystems (e.g., the internal combustion engine, motor, generator, and battery) has been a challenging control problem. One of the main aspects of the power management control algorithms is concerned with the self-sustainability of the electrical path, which must be guaranteed for the entire driving cycle. This paper considers the problem of identifying online the power required by the battery to maintain the state of charge within a range of the target value. An algorithm is presented that realizes how much power the engine needs to provide to the battery so that self-sustainability of the electrical path is maintained.

  2. Research, development, and demonstration of nickel-iron batteries for electric vehicle propulsion. Annual report, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    The objective of the Eagle-Picher nickel-iron battery program is to develop a nickel-iron battery for use in the propulsion of electric and electric-hybrid vehicles. To date, the program has concentrated on the characterization, fabrication and testing of the required electrodes, the fabrication and testing of full-scale cells, and finally, the fabrication and testing of full-scale (270 AH) six (6) volt modules. Electrodes of the final configuration have now exceeded 1880 cycles and are showing minimal capacity decline. Full-scale cells have presently exceeded 600 cycles and are tracking the individual electrode tests almost identically. Six volt module tests have exceeded 500 cycles, with a specific energy of 48 Wh/kg. Results to date indicate the nickel-iron battery is beginning to demonstrate the performance required for electric vehicle propulsion.

  3. Electromechanical Battery EMB Mass Minimization taking into Account its Electrical Machines Rotor Energy

    Directory of Open Access Journals (Sweden)

    Podgornovs Andrejs

    2014-12-01

    Full Text Available In this paper the electromechanical battery (EMB with synchronous machine is described. Theoretically, if electrical machines rotor stored energy is known, it is possible to reduce the flywheel mass of electromechanical battery. For example, the efficiency of energy recovery (kilowatt-hours out versus kilowatthours in in nowadays appliances exceeds 95 % which is considerably better than of any electrochemical battery, such as lead-acid battery. For the rotor stored energy amount calculation, it is necessary to find all geometrical dimensions of the electrical machine. To achieve this goal the iterative calculation method was used. Electromechanical battery mass was analyzed as a discharge process rotation speed function. Taking into account the rotor stored energy, we can increase the minimum rotation speed thus reducing the electrical machine mass and increasing the flywheel mass, which provides EMB cost reduction. Additionally, the possibilities of using numerical approximation calculations of magnetization curves are discussed. Each iteration of numerical application necessary for the method for rapid calculation is essential when calculating the field problems. Nowadays there are a lot of computer added design programs for electromagnetic field calculation in different types of applications, electrical machines and apparatus. For the electromagnetic field calculation process some more commonly used magnetization curve approximation methods are described, and the machine calculation time is tested for different numbers of calculations.

  4. Effects of Electric Vehicle Fast Charging on Battery Life and Vehicle Performance

    Energy Technology Data Exchange (ETDEWEB)

    Matthew Shirk; Jeffrey Wishart

    2015-04-01

    As part of the U.S. Department of Energy’s Advanced Vehicle Testing Activity, four new 2012 Nissan Leaf battery electric vehicles were instrumented with data loggers and operated over a fixed on-road test cycle. Each vehicle was operated over the test route, and charged twice daily. Two vehicles were charged exclusively by AC level 2 EVSE, while two were exclusively DC fast charged with a 50 kW charger. The vehicles were performance tested on a closed test track when new, and after accumulation of 50,000 miles. The traction battery packs were removed and laboratory tested when the vehicles were new, and at 10,000-mile intervals. Battery tests include constant-current discharge capacity, electric vehicle pulse power characterization test, and low peak power tests. The on-road testing was carried out through 70,000 miles, at which point the final battery tests were performed. The data collected over 70,000 miles of driving, charging, and rest are analyzed, including the resulting thermal conditions and power and cycle demands placed upon the battery. Battery performance metrics including capacity, internal resistance, and power capability obtained from laboratory testing throughout the test program are analyzed. Results are compared within and between the two groups of vehicles. Specifically, the impacts on battery performance, as measured by laboratory testing, are explored as they relate to battery usage and variations in conditions encountered, with a primary focus on effects due to the differences between AC level 2 and DC fast charging. The contrast between battery performance degradation and the effect on vehicle performance is also explored.

  5. Experimental Test Campaign on a Battery Electric Vehicle: On-Road Test Results (Part 2)

    OpenAIRE

    PAFFUMI Elena; DE GENNARO MICHELE; MARTINI Giorgio; MANFREDI URBANO; VIANELLI Stefano; ORTENZI Fernando; GENOVESE Antonino

    2014-01-01

    The experimental measurement of the energy consumption and efficiency of Battery Electric Vehicles (BEVs) are key topics to determine their usability and performance in real-world conditions. This paper aims to present the results of a test campaign carried out on a BEV, representative of the most common technology available today on the market. The vehicle is a 5-seat car, equipped with an 80 kW synchronous electric motor powered by a 24 kWh Li-Ion battery. The description and discussion of ...

  6. Cycle Life of Commercial Lithium-Ion Batteries with Lithium Titanium Oxide Anodes in Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Xuebing Han

    2014-07-01

    Full Text Available The lithium titanium oxide (LTO anode is widely accepted as one of the best anodes for the future lithium ion batteries in electric vehicles (EVs, especially since its cycle life is very long. In this paper, three different commercial LTO cells from different manufacturers were studied in accelerated cycle life tests and their capacity fades were compared. The result indicates that under 55 °C, the LTO battery still shows a high capacity fade rate. The battery aging processes of all the commercial LTO cells clearly include two stages. Using the incremental capacity (IC analysis, it could be judged that in the first stage, the battery capacity decreases mainly due to the loss of anode material and the degradation rate is lower. In the second stage, the battery capacity decreases much faster, mainly due to the degradation of the cathode material. The result is important for the state of health (SOH estimation and remaining useful life (RUL prediction of battery management system (BMS for LTO batteries in EVs.

  7. NAS battery demonstration at American Electric Power:a study for the DOE energy storage program.

    Energy Technology Data Exchange (ETDEWEB)

    Newmiller, Jeff (Endecon Engineering, San Ramon, CA); Norris, Benjamin L. (Norris Energy Consulting Company, Martinez, CA); Peek, Georgianne Huff

    2006-03-01

    The first U.S. demonstration of the NGK sodium/sulfur battery technology was launched in August 2002 when a prototype system was installed at a commercial office building in Gahanna, Ohio. American Electric Power served as the host utility that provided the office space and technical support throughout the project. The system was used to both reduce demand peaks (peak-shaving operation) and to mitigate grid power disturbances (power quality operation) at the demonstration site. This report documents the results of the demonstration, provides an economic analysis of a commercial sodium/sulfur battery energy storage system at a typical site, and describes a side-by-side demonstration of the capabilities of the sodium/sulfur battery system, a lead-acid battery system, and a flywheel-based energy storage system in a power quality application.

  8. Liquid cooled plate heat exchanger for battery cooling of an electric vehicle (EV)

    Science.gov (United States)

    Rahman, M. M.; Rahman, H. Y.; Mahlia, T. M. I.; Sheng, J. L. Y.

    2016-03-01

    A liquid cooled plate heat exchanger was designed to improve the battery life of an electric vehicle which suffers from premature aging or degradation due to the heat generation during discharging and charging period. Computational fluid dynamics (CFD) was used as a tool to analyse the temperature distribution when a constant surface heat flux was set at the bottom surface of the battery. Several initial and boundary conditions were set based on the past studies on the plate heat exchanger in the simulation software. The design of the plate heat exchanger was based on the Nissan Leaf battery pack to analyse the temperature patterns. Water at different mass flow rates was used as heat transfer fluid. The analysis revealed the designed plate heat exchanger could maintain the surface temperature within the range of 20 to 40°C which is within the safe operating temperature of the battery.

  9. Impact Safety Control Strategy for the Battery System of an Example Electric Bus

    Directory of Open Access Journals (Sweden)

    Zhen-po Wang

    2015-01-01

    Full Text Available This paper proposes a side impact safety control strategy for the battery system, aiming at defusing the hazards of unacceptable behaviors of the battery system such as high-voltage hazards. Based on some collision identification metrics, a side impact discrimination algorithm and a side impact severity algorithm are developed for electric buses. Based on the study on the time to break for power battery, the side impact discrimination algorithm response time is about 20 ms posing a great challenge to the side impact discrimination algorithm. At the same time, the reliability of the impact safety control strategy developed in this paper is evaluated for other plausible side impact signals generated by finite element analysis. The results verify that the impact safety control strategy exhibits robust performance and is able to trigger a breaking signal for power battery system promptly and accurately.

  10. An SCR inverter with an integral battery charger for electric vehicles

    Science.gov (United States)

    Thimmeach, D.

    1983-01-01

    The feasibility of incorporating an onboard battery charger into the inverter previously developed under a NASA contract is successfully demonstrated. The rated output power of the resulting isolated battery charger is 3.6 kW at 220 Vac with an 86 percent efficiency and a 95 percent power factor. Also achieved are improved inverter efficiency (from 90 to 93 percent at 15 kW motor shaft power), inverter peak power capability (from 26 to 34 kW), and reduced weight and volume of the combined inverter/charger package (47 kg, 49 x 44 x 24 cm). Some major conclusions are that using the inverter commutation circuitry to perform the battery charging function is advantageous, and that the input-commutated thyristor inverter has the potential to be an excellent inverter and battery charger for use in electric vehicle applications.

  11. Variability of Battery Wear in Light Duty Plug-In Electric Vehicles Subject to Ambient Temperature, Battery Size, and Consumer Usage: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wood, E.; Neubauer, J.; Brooker, A. D.; Gonder, J.; Smith, K. A.

    2012-08-01

    Battery wear in plug-in electric vehicles (PEVs) is a complex function of ambient temperature, battery size, and disparate usage. Simulations capturing varying ambient temperature profiles, battery sizes, and driving patterns are of great value to battery and vehicle manufacturers. A predictive battery wear model developed by the National Renewable Energy Laboratory captures the effects of multiple cycling and storage conditions in a representative lithium chemistry. The sensitivity of battery wear rates to ambient conditions, maximum allowable depth-of-discharge, and vehicle miles travelled is explored for two midsize vehicles: a battery electric vehicle (BEV) with a nominal range of 75 mi (121 km) and a plug-in hybrid electric vehicle (PHEV) with a nominal charge-depleting range of 40 mi (64 km). Driving distance distributions represent the variability of vehicle use, both vehicle-to-vehicle and day-to-day. Battery wear over an 8-year period was dominated by ambient conditions for the BEV with capacity fade ranging from 19% to 32% while the PHEV was most sensitive to maximum allowable depth-of-discharge with capacity fade ranging from 16% to 24%. The BEV and PHEV were comparable in terms of petroleum displacement potential after 8 years of service, due to the BEV?s limited utility for accomplishing long trips.

  12. A flexible Li-ion battery with design towards electrodes electrical insulation

    Science.gov (United States)

    Vieira, E. M. F.; Ribeiro, J. F.; Sousa, R.; Correia, J. H.; Goncalves, L. M.

    2016-08-01

    The application of micro electromechanical systems (MEMS) technology in several consumer electronics leads to the development of micro/nano power sources with high power and MEMS integration possibility. This work presents the fabrication of a flexible solid-state Li-ion battery (LIB) (~2.1 μm thick) with a design towards electrodes electrical insulation, using conventional, low cost and compatible MEMS fabrication processes. Kapton® substrate provides flexibility to the battery. E-beam deposited 300 nm thick Ge anode was coupled with LiCoO2/LiPON (cathode/solid-state electrolyte) in a battery system. LiCoO2 and LiPON films were deposited by RF-sputtering with a power source of 120 W and 100 W, respectively. LiCoO2 film was annealed at 400 °C after deposition. The new design includes Si3N4 and LiPO thin-films, providing electrode electrical insulation and a battery chemical stability safeguard, respectively. Microstructure and battery performance were investigated by scanning electron microscopy, electric resistivity and electrochemical measurements (open circuit potential, charge/discharge cycles and electrochemical impedance spectroscopy). A rechargeable thin-film and lightweight flexible LIB using MEMS processing compatible materials and techniques is reported.

  13. Safety and environmental aspects of zinc--chlorine hydrate batteries for electric-vehicle applications

    Energy Technology Data Exchange (ETDEWEB)

    Kodali, S.; Henriksen, G.L.; Whittlesey, C.C.; Warde, C.J.; Carr, P.; Symons, P.C.

    1978-03-01

    Public acceptance of high-performance cost-effective zinc--chlorine hydrate batteries for the random-use electric-vehicle application will require meeting stringent safety and environmental requirements. These requirements revolve mainly around the question of accidental release and spread of toxic amounts of chlorine gas, the only potential hazard in this battery system. Available information in the areas of physiological effects, environmental impact, and governmental regulation of chlorine were reviewed. The design, operation, and safety features of a first commercial electric-vehicle battery were conceived and analyzed from the chlorine release aspect. Two types of accident scenarios were analyzed in terms of chlorine release rates, atmospheric dispersion, health hazard, and possible clean-up operations. The worst-case scenario, a quite improbable accident, involves the spillage of chlorine hydrate onto the ground, while the other scenario, a more probable accident, involves the release of chlorine gas from a ruptured battery case. Heat-transfer and chlorine-dispersion models, developed to analyze these scenarios, establish a firm basis for a comprehenive and factual position statement on this topic. The results of this preliminary study suggest that electric vehicles powered by appropriately designed zinc--chlorine hydrate batteries will pose negligible health or environmental hazards on the nation's streets and highways. 8 figures, 14 tables.

  14. Selection of battery technology to support grid-integrated renewable electricity

    Science.gov (United States)

    Leadbetter, Jason; Swan, Lukas G.

    2012-10-01

    Operation of the electricity grid has traditionally been done using slow responding base and intermediate load generators with fast responding peak load generators to capture the chaotic behavior of end-use demands. Many modern electricity grids are implementing intermittent non-dispatchable renewable energy resources. As a result, the existing support services are becoming inadequate and technological innovation in grid support services are necessary. Support services fall into short (seconds to minutes), medium (minutes to hours), and long duration (several hours) categories. Energy storage offers a method of providing these services and can enable increased penetration rates of renewable energy generators. Many energy storage technologies exist. Of these, batteries span a significant range of required storage capacity and power output. By assessing the energy to power ratio of electricity grid services, suitable battery technologies were selected. These include lead-acid, lithium-ion, sodium-sulfur, and vanadium-redox. Findings show the variety of grid services require different battery technologies and batteries are capable of meeting the short, medium, and long duration categories. A brief review of each battery technology and its present state of development, commercial implementation, and research frontiers is presented to support these classifications.

  15. Modeling of a vanadium redox flow battery electricity storage system

    OpenAIRE

    Blanc, Christian

    2009-01-01

    Today, the electricity industries are facing new challenges as the market is being liberalized and deregulated in many countries. Electricity storage is undoubtedly a disruptive technology that will play, in the near future, a major role in the fast developing distributed generations network. Indeed, electricity storage has many potential applications: management of the supply and demand of electricity, power quality, integration of renewable sources, improvement of the level of use of the tr...

  16. Separator for alkaline electric batteries and method of making

    Science.gov (United States)

    Pfluger, H. L. (Inventor); Hoyt, H. E.

    1970-01-01

    Battery separator membranes of high electrolytic conductivity comprising a cellulose ether and a compatible metallic salt of water soluble aliphatic acids and their hydroxy derivatives are described. It was found that methyl cellulose can be modified by another class of materials, nonpolymeric in nature, to form battery separator membranes of low electrolytic resistance but which have the flexibility of membranes made of unmodified methyl cellulose, and which in many cases enhance flexibility over membranes made with unmodified methyl cellulose. Separator membranes for electrochemical cells comprising a cellulose ether and a modified selected from the group consisting of metallic salts of water soluble alphatic acids and their hydroxy derivatives and to electrochemical cells utilizing said membranes are described.

  17. Analysis of an electric Equivalent Circuit Model of a Li-Ion battery to develop algorithms for battery states estimation.

    OpenAIRE

    Shamsi, Mohammad Haris

    2016-01-01

    Batteries have imparted momentum to the process of transition towards a green future. However, mass application of batteries is obstructed due to their explosive nature, a trait specific to Li-Ion batteries. To cater to an efficient battery utilization, an introduction of a battery management system would provide an ultimate solution. This thesis deals with different aspects crucial in designing a battery management system for high energy as well as high power applications. To build a battery...

  18. Energy Consumption Of Battery Cooling In Hybrid Electric Vehicles

    OpenAIRE

    Krüger, Imke Lisa; Limperich, Dirk; Schmitz, Gerhard

    2012-01-01

    Lithium ion cells are presently the most promising technology for the use in hybrid vehicles. The cells heat up due to internal heat generation. This may lead to premature aging and necessitates an efficient thermal management. The heat sink for the cells is the automotive refrigeration cycle. The cells can be cooled by evaporation of the refrigerant or via a secondary coolant loop. Models for battery cooling systems are added to an existing Modelica library in order to examine the influence ...

  19. A Thermally-Regenerative Ammonia-Based Flow Battery for Electrical Energy Recovery from Waste Heat.

    Science.gov (United States)

    Zhu, Xiuping; Rahimi, Mohammad; Gorski, Christopher A; Logan, Bruce

    2016-04-21

    Large amounts of low-grade waste heat (temperatures electricity in battery systems. To improve reactor efficiency, a compact, ammonia-based flow battery (AFB) was developed and tested at different solution concentrations, flow rates, cell pairs, and circuit connections. The AFB achieved a maximum power density of 45 W m(-2) (15 kW m(-3) ) and an energy density of 1260 Wh manolyte (-3) , with a thermal energy efficiency of 0.7 % (5 % relative to the Carnot efficiency). The power and energy densities of the AFB were greater than those previously reported for thermoelectrochemical and salinity-gradient technologies, and the voltage or current could be increased using stacked cells. These results demonstrated that an ammonia-based flow battery is a promising technology to convert low-grade thermal energy to electricity. PMID:26990485

  20. Characterization, performance, and prediction of a lead-acid battery under simulated electric vehicle driving requirements

    Science.gov (United States)

    Ewashinka, J. G.; Bozek, J. M.

    1981-01-01

    A state-of-the-art 6-V battery module in current use by the electric vehicle industry was tested at the NASA Lewis Research Center to determine its performance characteristics under the SAE J227a driving schedules B, C, and D. The primary objective of the tests was to determine the effects of periods of recuperation and long and short periods of electrical regeneration in improving the performance of the battery module and hence extendng the vehicle range. A secondary objective was to formulate a computer program that would predict the performance of this battery module for the above driving schedules. The results show excellent correlation between the laboratory tests and predicted results. The predicted performance compared with laboratory tests was within +2.4 to -3.7 percent for the D schedule, +0.5 to -7.1 percent for the C schedule, and better than -11.4 percent for the B schedule.

  1. Computational models of an inductive power transfer system for electric vehicle battery charge

    Science.gov (United States)

    Anele, A. O.; Hamam, Y.; Chassagne, L.; Linares, J.; Alayli, Y.; Djouani, K.

    2015-09-01

    One of the issues to be solved for electric vehicles (EVs) to become a success is the technical solution of its charging system. In this paper, computational models of an inductive power transfer (IPT) system for EV battery charge are presented. Based on the fundamental principles behind IPT systems, 3 kW single phase and 22 kW three phase IPT systems for Renault ZOE are designed in MATLAB/Simulink. The results obtained based on the technical specifications of the lithium-ion battery and charger type of Renault ZOE show that the models are able to provide the total voltage required by the battery. Also, considering the charging time for each IPT model, they are capable of delivering the electricity needed to power the ZOE. In conclusion, this study shows that the designed computational IPT models may be employed as a support structure needed to effectively power any viable EV.

  2. Lead-acid traction batteries for electric road vehicle propulsion Directions for research and development

    Science.gov (United States)

    Rand, D. A. J.

    1980-09-01

    Little information exists on the behavior of lead-acid batteries operating under the duty cycles normal to electric road vehicle service. Important battery requirements for the propulsion of traffic-compatible electric vehicles include a deep-discharge capability at high efficiencies of active material utilization, and a long cycle life. In order to optimize power-source characteristics to meet these criteria, especially for passenger cars, it is necessary to gain full knowledge of the influence of actual vehicle service on the performance of traction batteries. This article defines areas in which both fundamental and applied work are required to achieve this aim based on the current performance of the lead-acid system.

  3. Current status of environmental, health, and safety issues of lithium polymer electric vehicle batteries

    Energy Technology Data Exchange (ETDEWEB)

    Corbus, D; Hammel, C J

    1995-02-01

    Lithium solid polymer electrolyte (SPE) batteries are being investigated by researchers worldwide as a possible energy source for future electric vehicles (EVs). One of the main reasons for interest in lithium SPE battery systems is the potential safety features they offer as compared to lithium battery systems using inorganic and organic liquid electrolytes. However, the development of lithium SPE batteries is still in its infancy, and the technology is not envisioned to be ready for commercialization for several years. Because the research and development (R&D) of lithium SPE battery technology is of a highly competitive nature, with many companies both in the United States and abroad pursuing R&D efforts, much of the information concerning specific developments of lithium SPE battery technology is proprietary. This report is based on information available only through the open literature (i.e., information available through library searches). Furthermore, whereas R&D activities for lithium SPE cells have focused on a number of different chemistries, for both electrodes and electrolytes, this report examines the general environmental, health, and safety (EH&S) issues common to many lithium SPE chemistries. However, EH&S issues for specific lithium SPE cell chemistries are discussed when sufficient information exists. Although lithium batteries that do not have a SPE are also being considered for EV applications, this report focuses only on those lithium battery technologies that utilize the SPE technology. The lithium SPE battery technologies considered in this report may contain metallic lithium or nonmetallic lithium compounds (e.g., lithium intercalated carbons) in the negative electrode.

  4. Can innovative business models overcome resistance to electric vehicles? Better Place and battery electric cars in Denmark

    International Nuclear Information System (INIS)

    This paper explores the geographical and policy context for an emergent business model from Better Place to deliver battery electric car mobility in Denmark. It argues that the combination of radically different technologies and a highly complex multi-agency operating environment theoretically provide the conditions and requirements for such an emergent business model. While focused on battery electric cars, renewable energy generation and smart grids, the paper has wider applicability to an understanding of the interplay between place, innovation and sustainability which suggests that diverse solutions are likely to be the characteristic solution rather than ubiquity and standardization. The paper argues, however, that the innovative business model, the deployment of electric vehicles, and the use of renewable energy systems, in this case largely based on wind power, while mutually supportive and contributing to wider policy aims with respect to the reduction of carbon emissions, may still fail in the face of entrenched practices. At the theoretical level it is concluded that theorization of business models needs a broader perspective beyond the typical ‘value creation, value capture’ rubric to better understand the wider role such models have in meeting societal goals, and to understand the structural impediments to organizational and technical innovation. - Highlights: ► We explore the context for an innovative emergent business model to deliver battery electric car mobility in Denmark. ► We explore the interplay between battery electric cars, renewable energy generation and smart grids. ► We discuss the integration of electric cars in energy systems based on renewable energy sources. ► We discuss the likely success of the Better Place business model.

  5. Plug-in hybrid electric vehicle charge pattern optimization for energy cost and battery longevity

    Science.gov (United States)

    Bashash, Saeid; Moura, Scott J.; Forman, Joel C.; Fathy, Hosam K.

    This paper examines the problem of optimizing the charge pattern of a plug-in hybrid electric vehicle (PHEV), defined as the timing and rate with which the PHEV obtains electricity from the power grid. The optimization goal is to simultaneously minimize (i) the total cost of fuel and electricity and (ii) the total battery health degradation over a 24-h naturalistic drive cycle. The first objective is calculated for a previously-developed stochastic optimal PHEV power management strategy, whereas the second objective is evaluated through an electrochemistry-based model of anode-side resistive film formation in lithium-ion batteries. The paper shows that these two objectives are conflicting, and trades them off using a non-dominated sorting genetic algorithm. As a result, a Pareto front of optimal charge patterns is obtained. The effects of electricity price and trip schedule on the optimal Pareto points and the PHEV charge patterns are analyzed and discussed.

  6. Comparison of Parametrization Techniques for an Electrical Circuit Model of Lithium-Sulfur Batteries

    DEFF Research Database (Denmark)

    Knap, Vaclav; Stroe, Daniel Loan; Teodorescu, Remus;

    2015-01-01

    on the comparison of different parametrization methods of electrical circuit models (ECMs) for Li-S batteries. These methods are used to parametrize an ECM based on laboratory measurements performed on a Li-S pouch cell. Simulation results of ECMs are presented and compared against measurement values...

  7. Development and testing of a bipolar lead-acid battery for hybrid electric vehicles

    NARCIS (Netherlands)

    Saakes, M.; Kluiters, E.; Schmal, D.; Mourad, S.; Have, P.T.J.H. ten

    1999-01-01

    An 80 V bipolar lead-acid battery was constructed and tested using hybrid electric vehicle (HEV) drive cycles. Drive cycles with a peak power of 6.7 kW, equal to 1/5 of the total power profile required for the HEV studied, were run successfully. Model calculations showed that the 80 V module constru

  8. Development and testing of a bipolar lead-acid battery for hybrid electric vehicles

    NARCIS (Netherlands)

    Mourad, S.; Saakes, M.; Kluiters, C.E.; Schmal, D.; Have, P. ten

    1998-01-01

    A 80V bipolar lead-acid battery was constructed and tested using Hybrid Electric Vehicle (HEV) drive cycles. Drive cycles with a peak power of 6.7kW, equal to 1/5 of the total power profile required for the HEV studied, were run succesfully. Model calculations showed that the constructed 80V module,

  9. A fault-tolerant control architecture for different battery topologies in electric vehicles

    DEFF Research Database (Denmark)

    Gholami, Mehdi; Esen, Hasan; Schiøler, Henrik;

    2012-01-01

    In this paper a variety of battery conguration topologies for electrical vehicles (EV)are investigated w.r.t. reliability and expected lifetime along with the possibility of applying active fault detection to provide early warnings for the driver. Dierent congurations are investigated ranging from...

  10. An Electric taxi fleet charged by second use batteries: not just economic profit

    OpenAIRE

    Canals Casals, Lluc; Amante García, Beatriz

    2013-01-01

    The road transport sector is the second biggest CO2 emissions contributor after energy generation. In urban environments, its impact is increased due to the worse combustion engine driving efficiency. It is thought that electric mobility might bring some relief to big cities’ polluted air. At the same time, car manufacturers are searching for second battery applications in order to reduce its manufacture cost and make electric cars achievable for most people. This paper seeks to a...

  11. Practical control schemes of a battery/supercapacitor system for electric vehicle

    OpenAIRE

    CASTAINGS, Ali; Lhomme, Walter; TRIGUI, Rochdi; Bouscayrol, Alain

    2015-01-01

    A hybrid energy storage system for electric vehicle using supercapacitors and a battery is studied. Using energetic macroscopic representation formalism, an inversion-based control (IBC) can be deduced. A comparison between IBC and two other control schemes is performed within a practical aspect. Simulation and experimental tests with a reduced-scale test bed are provided using a real driving cycle of an electric car. The results point out a more effective behaviour for the IBC than the other...

  12. Depollution benchmarks for capacitors, batteries and printed wiring boards from waste electrical and electronic equipment (WEEE)

    Energy Technology Data Exchange (ETDEWEB)

    Savi, Daniel, E-mail: d.savi@umweltchemie.ch [Dipl. Environmental Sci. ETH, büro für umweltchemie, Zurich (Switzerland); Kasser, Ueli [Lic. Phil. Nat. (Chemist), büro für umweltchemie, Zurich (Switzerland); Ott, Thomas [Dipl. Phys. ETH, Institute of Applied Simulation, Zurich University of Applied Sciences, Wädenswil (Switzerland)

    2013-12-15

    Highlights: • We’ve analysed data on the dismantling of electronic and electrical appliances. • Ten years of mass balance data of more than recycling companies have been considered. • Percentages of dismantled batteries, capacitors and PWB have been studied. • Threshold values and benchmarks for batteries and capacitors have been identified. • No benchmark for the dismantling of printed wiring boards should be set. - Abstract: The article compiles and analyses sample data for toxic components removed from waste electronic and electrical equipment (WEEE) from more than 30 recycling companies in Switzerland over the past ten years. According to European and Swiss legislation, toxic components like batteries, capacitors and printed wiring boards have to be removed from WEEE. The control bodies of the Swiss take back schemes have been monitoring the activities of WEEE recyclers in Switzerland for about 15 years. All recyclers have to provide annual mass balance data for every year of operation. From this data, percentage shares of removed batteries and capacitors are calculated in relation to the amount of each respective WEEE category treated. A rationale is developed, why such an indicator should not be calculated for printed wiring boards. The distributions of these de-pollution indicators are analysed and their suitability for defining lower threshold values and benchmarks for the depollution of WEEE is discussed. Recommendations for benchmarks and threshold values for the removal of capacitors and batteries are given.

  13. Depollution benchmarks for capacitors, batteries and printed wiring boards from waste electrical and electronic equipment (WEEE)

    International Nuclear Information System (INIS)

    Highlights: • We’ve analysed data on the dismantling of electronic and electrical appliances. • Ten years of mass balance data of more than recycling companies have been considered. • Percentages of dismantled batteries, capacitors and PWB have been studied. • Threshold values and benchmarks for batteries and capacitors have been identified. • No benchmark for the dismantling of printed wiring boards should be set. - Abstract: The article compiles and analyses sample data for toxic components removed from waste electronic and electrical equipment (WEEE) from more than 30 recycling companies in Switzerland over the past ten years. According to European and Swiss legislation, toxic components like batteries, capacitors and printed wiring boards have to be removed from WEEE. The control bodies of the Swiss take back schemes have been monitoring the activities of WEEE recyclers in Switzerland for about 15 years. All recyclers have to provide annual mass balance data for every year of operation. From this data, percentage shares of removed batteries and capacitors are calculated in relation to the amount of each respective WEEE category treated. A rationale is developed, why such an indicator should not be calculated for printed wiring boards. The distributions of these de-pollution indicators are analysed and their suitability for defining lower threshold values and benchmarks for the depollution of WEEE is discussed. Recommendations for benchmarks and threshold values for the removal of capacitors and batteries are given

  14. Economic analysis of second use electric vehicle batteries for residential energy storage and load-levelling

    International Nuclear Information System (INIS)

    The reuse of Li-ion EV batteries for energy storage systems (ESS) in stationary settings is a promising technology to support improved management of demand and supply of electricity. In this paper, MatLAB simulation of a residential energy profile and regulated cost structure is used to analyze the feasibility of and cost savings from repurposing an EV battery unit for peak-shifting. in situ residential energy storage can contribute to the implementation of a smart grid by supporting the reduction of demand during typical peak use periods. Use of an ESS increases household energy use but potentially improves economic effectiveness and reduces greenhouse gas emissions. The research supports the use of financial incentives for Li-ion battery reuse in ESS, including lower energy rates and reduced auxiliary fees. - Highlights: • EV Li-ion batteries can be reused in stationary energy storage systems (ESS). • A single ESS can shift 2 to 3 h of electricity used in a house. • While energy use increases, potential economic and environmental effectiveness improve. • ESS supports smart grid objectives. • Incentives like reduced fees are needed to encourage implementation of Li-ion battery ESS

  15. Tools for Designing Thermal Management of Batteries in Electric Drive Vehicles (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Pesaran, A.; Keyser, M.; Kim, G. H.; Santhanagopalan, S.; Smith, K.

    2013-02-01

    Temperature has a significant impact on life, performance, and safety of lithium-ion battery technology, which is expected to be the energy storage of choice for electric drive vehicles (xEVs). High temperatures degrade Li-ion cells faster while low temperatures reduce power and energy capabilities that could have cost, reliability, range, or drivability implications. Thermal management of battery packs in xEVs is essential to keep the cells in the desired temperature range and also reduce cell-to-cell temperature variations, both of which impact life and performance. The value that the battery thermal management system provides in reducing battery life and improving performance outweighs its additional cost and complexity. Tools that are essential for thermal management of batteries are infrared thermal imaging, isothermal calorimetry, thermal conductivity meter and computer-aided thermal analysis design software. This presentation provides details of these tools that NREL has used and we believe are needed to design right-sized battery thermal management systems.

  16. Recursive calibration for a lithium iron phosphate battery for electric vehicles using extended Kalman filtering

    Institute of Scientific and Technical Information of China (English)

    Xiao-song HU; Feng-chun SUN; Xi-ming CHENG

    2011-01-01

    In this paper,an efficient model structure composed of a second-order resistance-capacitance networkand a simply analytical open circuit voltage versus state of charge(SOC)map is applied to characterize the voltage behavior of a lithium iron phosphate battery for electric vehicles(EVs).As a result,the overpotentials of the battery can be depicted using a second-order circuit network and the model parameterization can be realized under any battery loading profile,without a special characterization experiment.In order to ensure good robustness,extended Kalman filtering is adopted to recursively implement the calibration process.The linearization involved in the calibration algorithm is realized through recurrent derivatives in a recursive form.Validation results show that the recursively calibrated battery model can accurately delineate the battery voltage behavior under two different transient power operating conditions.A comparison with a first-order model indicates that the recursively calibrated second-order model has a comparable accuracy in a major part of the battery SOC range and a better performance when the SOC is relatively low.

  17. The influence of battery degradation level on the selected traction parameters of a light-duty electric vehicle

    Science.gov (United States)

    Juda, Z.; Noga, M.

    2016-09-01

    The article describes results of an analysis of the impact of degradation level of battery made in lead-acid technology on selected traction parameters of an electric light duty vehicle. Lead-acid batteries are still used in these types of vehicles. They do not require complex systems of performance management and monitoring and are easy to maintaining. Despite the basic disadvantage, which is the low value of energy density, low price is a decisive factor for their use in low-speed electric vehicles. The process of aging of the battery related with an increase in internal resistance of the cells and the loss of electric capacity of the battery was considered. A simplified model of cooperation of the DC electric motor with the battery assuming increased internal resistance was presented. In the paper the results of comparative traction research of the light-duty vehicle equipped with a set of new batteries and set of batteries having a significant degradation level were showed. The analysis of obtained results showed that the correct exploitation of the battery can slow down the processes of degradation and, thus, extend battery life cycle.

  18. NREL Reveals Links Among Climate Control, Battery Life, and Electric Vehicle Range (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2012-06-01

    Researchers at the National Renewable Energy Laboratory (NREL) are providing new insights into the relationships between the climate-control systems of plug-in electric vehicles and the distances these vehicles can travel on a single charge. In particular, NREL research has determined that 'preconditioning' a vehicle-achieving a comfortable cabin temperature and preheating or precooling the battery while the vehicle is still plugged in-can extend its driving range and improve battery life over the long term.

  19. Qualitative thermal characterization and cooling of lithium batteries for electric vehicles

    International Nuclear Information System (INIS)

    The paper deals with the cooling of batteries. The first step was the thermal characterization of a single cell of the module, which consists in the detection of the thermal field by means of thermographic tests during electric charging and discharging. The purpose was to identify possible critical hot points and to evaluate the cooling demand during the normal operation of an electric car. After that, a study on the optimal configuration to obtain the flattening of the temperature profile and to avoid hot points was executed. An experimental plant for cooling capacity evaluation of the batteries, using air as cooling fluid, was realized in our laboratory in ENEA Casaccia. The plant is designed to allow testing at different flow rate and temperatures of the cooling air, useful for the assessment of operative thermal limits in different working conditions. Another experimental facility was built to evaluate the thermal behaviour changes with water as cooling fluid. Experimental tests were carried out on the LiFePO4 batteries, under different electric working conditions using the two loops. In the future, different type of batteries will be tested and the influence of various parameters on the heat transfer will be assessed for possible optimal operative solutions.

  20. Qualitative thermal characterization and cooling of lithium batteries for electric vehicles

    Science.gov (United States)

    Mariani, A.; D'Annibale, F.; Boccardi, G.; Celata, G. P.; Menale, C.; Bubbico, R.; Vellucci, F.

    2014-04-01

    The paper deals with the cooling of batteries. The first step was the thermal characterization of a single cell of the module, which consists in the detection of the thermal field by means of thermographic tests during electric charging and discharging. The purpose was to identify possible critical hot points and to evaluate the cooling demand during the normal operation of an electric car. After that, a study on the optimal configuration to obtain the flattening of the temperature profile and to avoid hot points was executed. An experimental plant for cooling capacity evaluation of the batteries, using air as cooling fluid, was realized in our laboratory in ENEA Casaccia. The plant is designed to allow testing at different flow rate and temperatures of the cooling air, useful for the assessment of operative thermal limits in different working conditions. Another experimental facility was built to evaluate the thermal behaviour changes with water as cooling fluid. Experimental tests were carried out on the LiFePO4 batteries, under different electric working conditions using the two loops. In the future, different type of batteries will be tested and the influence of various parameters on the heat transfer will be assessed for possible optimal operative solutions.

  1. Electric Vehicles and Power Batteries%电动汽车与动力电池

    Institute of Scientific and Technical Information of China (English)

    艾新平; 杨汉西

    2011-01-01

    In retrospect of the historical development of Electric Vehicles ( EV), the impact of battery technologies on the progress of EV was discussed. In consequence, it is concluded that the lack of advanced batteries was the main cause for the fluctuations of EV development in the past century and reduce the progress of the commercialization of electric cars. After a brief introduction to the classification and the requirements of electric vehicles, the main issues including safety, wide temperature operation range and the cost, which now be frequenfly encountered in scaling-up lithium ion batteries for EV applications were discussed. Finally, the hot areas for future development in EV battery technologies were briefly analyzed.%回顾电动汽车一百多年的发展历史,讨论了化学电源技术对电动汽车发展的影响.在简要介绍电动汽车种类和电动汽车对动力电池的技术要求之后,集中讨论了动力锂离子电池应用的主要问题,包括电池安全性、环境适应性和成本.最后,简单分析了未来动力电池技术的发展之路.

  2. An Electric Bus with a Battery Exchange System

    OpenAIRE

    Jeongyong Kim; Inho Song; Woongchul Choi

    2015-01-01

    As part of the ongoing effort to be independent of petroleum resources and to be free from pollutant emission issues, various electric vehicles have been developed and tested through their integration with real world systems. In the current paper, yet another application specific EV for public transportation, an electric bus, is introduced and explained with results from the pilot test program which was carried out under real traffic conditions. The main feature of the current system is a bat...

  3. Natural graphite demand and supply: Implications for electric vehicle battery requirements.

    Science.gov (United States)

    Olson, Donald W.; Virta, Robert L.; Mahdavi, Mahbood; Sangine, Elizabeth S.; Fortier, Steven M.

    2016-01-01

    Electric vehicles have been promoted to reduce greenhouse gas emissions and lessen U.S. dependence on petroleum for transportation. Growth in U.S. sales of electric vehicles has been hindered by technical difficulties and the high cost of the lithium-ion batteries used to power many electric vehicles (more than 50% of the vehicle cost). Groundbreaking has begun for a lithium-ion battery factory in Nevada that, at capacity, could manufacture enough batteries to power 500,000 electric vehicles of various types and provide economies of scale to reduce the cost of batteries. Currently, primary synthetic graphite derived from petroleum coke is used in the anode of most lithium-ion batteries. An alternate may be the use of natural flake graphite, which would result in estimated graphite cost reductions of more than US$400 per vehicle at 2013 prices. Most natural flake graphite is sourced from China, the world's leading graphite producer. Sourcing natural flake graphite from deposits in North America could reduce raw material transportation costs and, given China's growing internal demand for flake graphite for its industries and ongoing environmental, labor, and mining issues, may ensure a more reliable and environmentally conscious supply of graphite. North America has flake graphite resources, and Canada is currently a producer, but most new mining projects in the United States require more than 10 yr to reach production, and demand could exceed supplies of flake graphite. Natural flake graphite may serve only to supplement synthetic graphite, at least for the short-term outlook.

  4. A new controller for battery-powered electric vehicles

    Science.gov (United States)

    Belsterling, C. A.; Stone, J.

    1980-01-01

    This paper describes the development, under a NASA/DOE contract, of a new concept for efficient and reliable control of battery-powered vehicles. It avoids the detrimental effects of pulsed-power controllers like the SCR 'chopper' by using rotating machines to meter continuous currents to the traction motor. The concept is validated in a proof-of-principle demonstration system and a complete vehicle is simulated on an analog computer. Test results show exceptional promise for a full-scale system. Optimum control strategies to minimize controller weight are developed by means of the simulated vehicle. The design for an Engineering Model is then prepared in the form of a practical, compact two-bearing package with forced air cooling. Predicted performance is outstanding, with controller efficiency of over 90% at high speed.

  5. Research results from the advanced lead-acid battery consortium point the way to longer life and higher specific energy for lead/acid electric-vehicle batteries

    Energy Technology Data Exchange (ETDEWEB)

    Moseley, P.T. [The International Lead Zinc Research Organization, Research Triangle Park, NC (United States)

    1998-05-18

    Amidst the welter of publicity devoted to the newer battery chemistries, the remarkable progress made by lead/acid battery technologists in response to the needs of the emerging electric-vehicle market has tended to be overlooked. The flooded design of battery, launched by Gaston Plante around 1860, has given way to a valve-regulated variant which has a history dating only from the 1970s. The key parameters of this `maintenance free` battery have been improved markedly during the course of the development programme of the advanced lead-acid battery consortium (ALABC), and it is likely that lead/acid will continue to feature strongly in motive-power applications as a result of its cost advantage and of its enhanced effectiveness. (orig.)

  6. Research results from the Advanced Lead-Acid Battery Consortium point the way to longer life and higher specific energy for lead/acid electric-vehicle batteries

    Science.gov (United States)

    Moseley, P. T.

    Amidst the welter of publicity devoted to the newer battery chemistries, the remarkable progress made by lead/acid battery technologists in response to the needs of the emerging electric-vehicle market has tended to be overlooked. The flooded design of battery, launched by Gaston Planté around 1860, has given way to a valve-regulated variant which has a history dating only from the 1970s. The key parameters of this `maintenance free' battery have been improved markedly during the course of the development programme of the Advanced Lead-Acid Battery Consortium (ALABC), and it is likely that lead/acid will continue to feature strongly in motive-power applications as a result of its cost advantage and of its enhanced effectiveness.

  7. Battery Electric Vehicles can reduce greenhouse has emissions and make renewable energy cheaper in India

    Energy Technology Data Exchange (ETDEWEB)

    Gopal, Anand R [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Witt, Maggie [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sheppard, Colin [Humboldt State Univ., Arcata, CA (United States); Harris, Andrew [Humboldt State Univ., Arcata, CA (United States)

    2015-07-01

    India's National Mission on Electric Mobility (NMEM) sets a countrywide goal of deploying 6 to 7 million hybrid and electric vehicles (EVs) by 2020. There are widespread concerns, both within and outside the government, that the Indian grid is not equipped to accommodate additional power demand from battery electric vehicles (BEVs). Such concerns are justified on the grounds of India's notorious power sector problems pertaining to grid instability and chronic blackouts. Studies have claimed that deploying BEVs in India will only

  8. Study on battery state of charge correct algorithm of electric vehicle

    Institute of Scientific and Technical Information of China (English)

    KAN Ping; QIAN Lijun

    2012-01-01

    State of Charge (SOC) is used to adjust the initialization SOC value so as to make electric vehicle simulation results close to real vehicle performance. This paper firstly analyses the battery SOC correct algorithm, then uses ADVISOR which is a electric vehicle simulation software to simulate a hybrid electric car with three different cases of no SOC correct, linear SOC correct and zero delta SOC correct, as well as makes the compare and analysis for those simulation results. In the end, an overall conclusion to SOC correct algorithm is given.

  9. Thermoelectric Modeling and Online SOC Estimation of Li-Ion Battery for Plug-In Hybrid Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Aishwarya Panday

    2016-01-01

    Full Text Available The increasing oil price, energy demand, and environmental concern are leading to a global switch towards Plug-In Hybrid Electric Vehicles (PHEVs. In a PHEV, Li-ion battery is considered as the primary propelling source. Therefore, an accurate battery model is required to predict the I-V characteristic and dynamic behavior of a battery. This paper presents a highly effective thermoelectric model of Li-ion battery developed in Simulink. An algorithm is proposed for estimation of state of charge (SOC and open circuit voltage (OCV adaptively to notify the exact SOC level for better utilization of battery power and optimal vehicle performance. Thermal behavior of Li-ion battery is investigated for wide temperature range and its effect on resistance, capacity, and OCV is recorded. The minimum SOC level to which battery can get depleted is calculated using gradient method. The proposed simulation results are analyzed with those of earlier models and found to be better.

  10. On the electrification of road transport - Learning rates and price forecasts for hybrid-electric and battery-electric vehicles

    International Nuclear Information System (INIS)

    Hybrid-electric vehicles (HEVs) and battery-electric vehicles (BEVs) are currently more expensive than conventional passenger cars but may become cheaper due to technological learning. Here, we obtain insight into the prospects of future price decline by establishing ex-post learning rates for HEVs and ex-ante price forecasts for HEVs and BEVs. Since 1997, HEVs have shown a robust decline in their price and price differential at learning rates of 7±2% and 23±5%, respectively. By 2010, HEVs were only 31±22 €2010 kW−1 more expensive than conventional cars. Mass-produced BEVs are currently introduced into the market at prices of 479±171 €2010 kW−1, which is 285±213 €2010 kW−1 and 316±209 €2010 kW−1 more expensive than HEVs and conventional cars. Our forecast suggests that price breakeven with these vehicles may only be achieved by 2026 and 2032, when 50 and 80 million BEVs, respectively, would have been produced worldwide. We estimate that BEVs may require until then global learning investments of 100–150 billion € which is less than the global subsidies for fossil fuel consumption paid in 2009. These findings suggest that HEVs, including plug-in HEVs, could become the dominant vehicle technology in the next two decades, while BEVs may require long-term policy support. - Highlights: ► Learning rates for hybrid-electric and battery-electric vehicles. ► Prices and price differentials of hybrid-electric vehicles show a robust decline. ► Battery-electric vehicles may require policy support for decades.

  11. A Coupled Dynamical Model of Redox Flow Battery Based on Chemical Reaction, Fluid Flow, and Electrical Circuit

    OpenAIRE

    Li, Minghua; Hikihara, Takashi

    2008-01-01

    The redox (Reduction-Oxidation) flow battery is one of the most promising rechargeable batteries due to its ability to average loads and output of power sources. The transient characteristics are well known as the remarkable feature of the battery. Then it can also compensate for a sudden voltage drop. The dynamics are governed by the chemical reactions, fluid flow, and electrical circuit of its structure. This causes the difficulty of the analysis at transient state. This paper discusses the...

  12. Batteries for Plug-in Hybrid Electric Vehicles (PHEVs): Goals and the State of Technology circa 2008

    OpenAIRE

    Axsen, Jonn; Burke, Andy; Kurani, Kenneth S

    2008-01-01

    This report discusses the development of advanced batteries for plug-in hybrid electric vehicle (PHEV) applications. We discuss the basic design concepts of PHEVs, compare three sets of influential technical goals, and explain the inherent trade-offs in PHEV battery design. We then discuss the current state of several battery chemistries, including nickel-metal hydride (NiMH) and lithium-ion (Li-Ion), comparing their abilities to meet PHEV goals, and potential trajectories for further improve...

  13. Electrically rechargeable zinc/air battery: a high specific energy system

    Energy Technology Data Exchange (ETDEWEB)

    Holzer, F.; Sauter, J.-C.; Masanz, G.; Mueller, S. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    This contribution describes our research and development efforts towards the demonstration of a light-weight, low-cost 12 V/20 Ah electrically rechargeable Zn/air battery. We successfully developed electrodes having active areas of up to 200 cm{sup 2}. Deep discharge cycles at different currents as well as current-voltage curves are reported for a 10 cell Zn/air battery (serial connection) with a rated capacity of 20 Ah. Based on the discharge cycle at a power of 19 W, and the weight of the battery, a specific energy of more than 90 Wh/kg could be evaluated for the whole system. (author) 4 figs., 1 tab., 5 refs.

  14. Detection and Elimination of a Potential Fire in Engine and Battery Compartments of Hybrid Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Macam S. Dattathreya

    2012-01-01

    Full Text Available This paper presents a novel fuzzy deterministic noncontroller type (FDNCT system and an FDNCT inference algorithm (FIA. The FDNCT uses fuzzy inputs and produces a deterministic non-fuzzy output. The FDNCT is an extension and alternative for the existing fuzzy singleton inference algorithm. The research described in this paper applies FDNCT to build an architecture for an intelligent system to detect and to eliminate potential fires in the engine and battery compartments of a hybrid electric vehicle. The fuzzy inputs consist of sensor data from the engine and battery compartments, namely, temperature, moisture, and voltage and current of the battery. The system synthesizes the data and detects potential fires, takes actions for eliminating the hazard, and notifies the passengers about the potential fire using an audible alarm. This paper also presents the computer simulation results of the comparison between the FIA and singleton inference algorithms for detecting potential fires and determining the actions for eliminating them.

  15. Comparison of Plug-In Hybrid Electric Vehicle Battery Life Across Geographies and Drive-Cycles

    Energy Technology Data Exchange (ETDEWEB)

    Smith, K.; Warleywine, M.; Wood, E.; Neubauer, J.; Pesaran, A.

    2012-06-01

    In a laboratory environment, it is cost prohibitive to run automotive battery aging experiments across a wide range of possible ambient environment, drive cycle and charging scenarios. Since worst-case scenarios drive the conservative sizing of electric-drive vehicle batteries, it is useful to understand how and why those scenarios arise and what design or control actions might be taken to mitigate them. In an effort to explore this problem, this paper applies a semi-empirical life model of the graphite/nickel-cobalt-aluminum lithium-ion chemistry to investigate impacts of geographic environments under storage and simplified cycling conditions. The model is then applied to analyze complex cycling conditions, using battery charge/discharge profiles generated from simulations of PHEV10 and PHEV40 vehicles across 782 single-day driving cycles taken from Texas travel survey data.

  16. Comparison of Plug-In Hybrid Electric Vehicle Battery Life Across Geographies and Drive-Cycles

    International Nuclear Information System (INIS)

    In a laboratory environment, it is cost prohibitive to run automotive battery aging experiments across a wide range of possible ambient environment, drive cycle and charging scenarios. Since worst-case scenarios drive the conservative sizing of electric-drive vehicle batteries, it is useful to understand how and why those scenarios arise and what design or control actions might be taken to mitigate them. In an effort to explore this problem, this paper applies a semi-empirical life model of the graphite/nickel-cobalt-aluminum lithium-ion chemistry to investigate impacts of geographic environments under storage and simplified cycling conditions. The model is then applied to analyze complex cycling conditions, using battery charge/discharge profiles generated from simulations of PHEV10 and PHEV40 vehicles across 782 single-day driving cycles taken from Texas travel survey data.

  17. Modelling and experimental evaluation of parallel connected lithium ion cells for an electric vehicle battery system

    Science.gov (United States)

    Bruen, Thomas; Marco, James

    2016-04-01

    Variations in cell properties are unavoidable and can be caused by manufacturing tolerances and usage conditions. As a result of this, cells connected in series may have different voltages and states of charge that limit the energy and power capability of the complete battery pack. Methods of removing this energy imbalance have been extensively reported within literature. However, there has been little discussion around the effect that such variation has when cells are connected electrically in parallel. This work aims to explore the impact of connecting cells, with varied properties, in parallel and the issues regarding energy imbalance and battery management that may arise. This has been achieved through analysing experimental data and a validated model. The main results from this study highlight that significant differences in current flow can occur between cells within a parallel stack that will affect how the cells age and the temperature distribution within the battery assembly.

  18. An adaptive remaining energy prediction approach for lithium-ion batteries in electric vehicles

    Science.gov (United States)

    Wang, Yujie; Zhang, Chenbin; Chen, Zonghai

    2016-02-01

    With the growing number of electric vehicle (EV) applications, the function of the battery management system (BMS) becomes more sophisticated. The accuracy of remaining energy estimation is critical for energy optimization and management in EVs. Therefore the state-of-energy (SoE) is defined to indicate the remaining available energy of the batteries. Considering that there are inevitable accumulated errors caused by current and voltage integral method, an adaptive SoE estimator is first established in this paper. In order to establish a reasonable battery equivalent model, based on the experimental data of the LiFePO4 battery, a data-driven model is established to describe the relationship between the open-circuit voltage (OCV) and the SoE. What is more, the forgetting factor recursive least-square (RLS) method is used for parameter identification to get accurate model parameters. Finally, in order to analyze the robustness and the accuracy of the proposed approach, different types of dynamic current profiles are conducted on the lithium-ion batteries and the performances are calculated and compared. The results indicate that the proposed approach has robust and accurate SoE estimation results under dynamic working conditions.

  19. Driving rural energy access: a second-life application for electric-vehicle batteries

    International Nuclear Information System (INIS)

    Building rural energy infrastructure in developing countries remains a significant financial, policy and technological challenge. The growth of the electric vehicle (EV) industry will rapidly expand the resource of partially degraded, ‘retired’, but still usable batteries in 2016 and beyond. These batteries can become the storage hubs for community-scale grids in the developing world. We model the resource and performance potential and the technological and economic aspects of the utilization of retired EV batteries in rural and decentralized mini- and micro-grids. We develop and explore four economic scenarios across three battery chemistries to examine the impacts on transport and recycling logistics. We find that EVs sold through 2020 will produce 120–549 GWh in retired storage potential by 2028. Outlining two use scenarios for decentralized systems, we discuss the possible impacts on global electrification rates. We find that used EV batteries can provide a cost-effective and lower environmental impact alternative to existing lead-acid storage systems in these applications. (letter)

  20. Lithium polymer batteries and proton exchange membrane fuel cells as energy sources in hydrogen electric vehicles

    Science.gov (United States)

    Corbo, P.; Migliardini, F.; Veneri, O.

    This paper deals with the application of lithium ion polymer batteries as electric energy storage systems for hydrogen fuel cell power trains. The experimental study was firstly effected in steady state conditions, to evidence the basic features of these systems in view of their application in the automotive field, in particular charge-discharge experiments were carried at different rates (varying the current between 8 and 100 A). A comparison with conventional lead acid batteries evidenced the superior features of lithium systems in terms of both higher discharge rate capability and minor resistance in charge mode. Dynamic experiments were carried out on the overall power train equipped with PEM fuel cell stack (2 kW) and lithium batteries (47.5 V, 40 Ah) on the European R47 driving cycle. The usage of lithium ion polymer batteries permitted to follow the high dynamic requirement of this cycle in hard hybrid configuration, with a hydrogen consumption reduction of about 6% with respect to the same power train equipped with lead acid batteries.

  1. Lithium polymer batteries and proton exchange membrane fuel cells as energy sources in hydrogen electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Corbo, P.; Migliardini, F.; Veneri, O. [Istituto Motori - National Research Council (CNR), Via Marconi, 8, 80125 Napoli (Italy)

    2010-12-01

    This paper deals with the application of lithium ion polymer batteries as electric energy storage systems for hydrogen fuel cell power trains. The experimental study was firstly effected in steady state conditions, to evidence the basic features of these systems in view of their application in the automotive field, in particular charge-discharge experiments were carried at different rates (varying the current between 8 and 100 A). A comparison with conventional lead acid batteries evidenced the superior features of lithium systems in terms of both higher discharge rate capability and minor resistance in charge mode. Dynamic experiments were carried out on the overall power train equipped with PEM fuel cell stack (2 kW) and lithium batteries (47.5 V, 40 Ah) on the European R47 driving cycle. The usage of lithium ion polymer batteries permitted to follow the high dynamic requirement of this cycle in hard hybrid configuration, with a hydrogen consumption reduction of about 6% with respect to the same power train equipped with lead acid batteries. (author)

  2. Lithium-ion cell-to-cell variation during battery electric vehicle operation

    Science.gov (United States)

    Schuster, Simon F.; Brand, Martin J.; Berg, Philipp; Gleissenberger, Markus; Jossen, Andreas

    2015-11-01

    484 new and 1908 aged lithium-ion cells out of two identical battery electric vehicles (i.e. 954 cells each) were characterized by capacity and impedance measurements to yield a broad set of data for distribution fit analysis. Results prove alteration from normal to Weibull distribution for the parameters of lithium-ion cells with the progress of aging. Cells with abnormal characteristics in the aged state mostly exhibit lower capacities as compared to the distribution mode which is typical for the left-skewed Weibull shape. In addition, the strength of variation and the amount of outliers both are generally increased with the aging progress. Obtained results are compared to vehicles' operational data to provide recommendations with the aim to minimize the increasing parameter spread. However, neither temperature gradients in the battery pack nor an insufficient balancing procedure were determined. As the appearance of cells with suspicious parameters could not be assigned to local weak spots of the battery pack, a random and inevitable type of origin is assumed. Hence, the battery management system must ensure to detect outliers in a reliable manner and to balance resulting drifts of cells' states of charge to guarantee a safe battery storage operation.

  3. State of available capacity estimation for lead-acid batteries in electric vehicles using neural network

    International Nuclear Information System (INIS)

    This paper reviews recent definitions of the state of charge (SOC) that are often used to estimate the battery residual available capacity (BRAC) for lead-acid batteries in electric vehicles (EVs) and identifies their shortcomings. Then, the state of available capacity (SOAC), instead of the SOC, is defined to denote the BRAC in EVs, which refers to the percentage of the battery available capacity (BAC) of the discharge current profile for the EV battery at the fully charged state. Based on the experimentation of different discharge current profiles, including theoretical current profiles and practical current profiles under EV driving cycles, the discharged and regenerative capacity distribution is proposed to describe discharge current profiles for the SOAC estimation. Because of the complexity and nonlinearity of the relationship between the SOAC and the capacity distribution at different temperatures, a neural network (NN) is applied to this SOAC estimation. Comparisons between the estimated SOACs by the NN and the calculated SOACs from the experimental data are used for verification. The results confirm that the proposed approach can provide an accurate and effective estimation of the BRAC for lead-acid batteries in EVs

  4. Design, control and power management of a battery/ultra-capacitor hybrid system for small electric vehicles

    DEFF Research Database (Denmark)

    Li, Zhihao; Onar, Omer; Khaligh, Alireza;

    2009-01-01

    This paper introduces design, control, and power management of a battery/ultra-capacitor hybrid system, utilized for small electric vehicles (EV). The batteries are designed and controlled to work as the main energy storage source of the vehicle, supplying average power to the load; and the ultra...

  5. Research, development, and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report for 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    Progress in developing nickel-zinc batteries for propelling electric vehicles is reported. Information is included on component design, battery fabrication, and module performance testing. Although full scale hardware performance has fallen short of the contract cycle life goals, significant progress has been made to warrant further development. (LCL)

  6. ESTIMATION METHOD ON THE BATTERY STATE OF CHARGE FOR HYBRID ELECTRIC VEHICLE

    Institute of Scientific and Technical Information of China (English)

    QIANG Jiaxi; AO Guoqiang; YANG Lin

    2008-01-01

    A combined algorithm for battery state of charge (SOC) estimation is proposed to solve the critical issue of hybrid electric vehicle (HEV). To obtain a more accurate SOC, both coulomb-accumulation and battery resistance-capacitor (RC) model are weighted combined to compensate the deficiencies of individual methods. In order to solve the key issue of coulomb-accumulation, the battery thermal model is used. Based on the principle of energy conservation, the heat generated from battery charge and discharge process is converted into the equivalent electricity to calculate charge and discharge efficiency under variable current. The extended Kalman filter (EKF) as a closed loop algorithm is applied to estimate the parameters of resistance-capacitor model. The input variables do not increase much computing difficulty. The proposed combined algorithm is implemented by adjusting the weighting factor of coulomb- accumulation and resistance-capacitor model. In the end, four different methods including Ah-efficiency, Ah-Equip, RC-SOC and Combined-SOC are compared in federal testing procedure (FTP) drive cycle. The experiment results show that the proposed method has good robustness and high accuracy which is suitable for HEV application.

  7. Advanced dc motor controller for battery-powered electric vehicles

    Science.gov (United States)

    Belsterling, C. A.

    1981-01-01

    A motor generation set is connected to run from the dc source and generate a voltage in the traction motor armature circuit that normally opposes the source voltage. The functional feasibility of the concept is demonstrated with tests on a Proof of Principle System. An analog computer simulation is developed, validated with the results of the tests, applied to predict the performance of a full scale Functional Model dc Controller. The results indicate high efficiencies over wide operating ranges and exceptional recovery of regenerated energy. The new machine integrates both motor and generator on a single two bearing shaft. The control strategy produces a controlled bidirectional plus or minus 48 volts dc output from the generator permitting full control of a 96 volt dc traction motor from a 48 volt battery, was designed to control a 20 hp traction motor. The controller weighs 63.5 kg (140 lb.) and has a peak efficiency of 90% in random driving modes and 96% during the SAE J 227a/D driving cycle.

  8. Battery sizing for serial plug-in hybrid electric vehicles: A model-based economic analysis for Germany

    International Nuclear Information System (INIS)

    The battery size of a Plug-in Hybrid Electric Vehicle (PHEV) is decisive for the electrical range of the vehicle and crucial for the cost-effectiveness of this particular vehicle concept. Based on the energy consumption of a conventional reference car and a PHEV, we introduce a comprehensive total cost of ownership model for the average car user in Germany for both vehicle types. The model takes into account the purchase price, fixed annual costs and variable operating costs. The amortization time of a PHEV also depends on the recharging strategy (once a day, once a night, after each trip), the battery size, and the battery costs. We find that PHEVs with a 4 kWh battery and at current lithium-ion battery prices reach the break-even point after about 6 years (5 years when using the lower night-time electricity tariffs). With higher battery capacities the amortization time becomes significantly longer. Even for the small battery size and assuming the EU-15 electricity mix, a PHEV is found to emit only around 60% of the CO2 emissions of a comparable conventional car. Thus, with the PHEV concept a cost-effective introduction of electric mobility and reduction of greenhouse gas emissions per vehicle can be reached. - Highlights: → Total cost of ownership of a PHEV and a conventional car are compared for the average German car user.→ PHEVs with a 4 kWh battery reach the break-even after 5-6 years at current Li-Ion battery prices.→ Even with a small battery, PHEVs emit about 40% less CO2 emissions than the average conventional car.

  9. Estimation of State of Charge of a Lithium-Ion Battery Pack for Electric Vehicles Using an Adaptive Luenberger Observer

    OpenAIRE

    Yuan Zou; Fengchun Sun; Xiaosong Hu

    2010-01-01

    In order to safely and efficiently use the power as well as to extend the lifetime of the traction battery pack, accurate estimation of State of Charge (SoC) is very important and necessary. This paper presents an adaptive observer-based technique for estimating SoC of a lithium-ion battery pack used in an electric vehicle (EV). The RC equivalent circuit model in ADVISOR is applied to simulate the lithium-ion battery pack. The parameters of the battery model as a function of SoC, are identifi...

  10. Operation Modes of Battery Chargers for Electric Vehicles in the Future Smart Grids

    OpenAIRE

    Monteiro, Vítor; Ferreira, João,; Afonso, João

    2014-01-01

    This paper presents an on-board bidirectional battery charger for Electric Vehicles (EVs), which operates in three different modes: Grid-to- Vehicle (G2V), Vehicle-to-Grid (V2G), and Vehicle-to-Home (V2H). Through these three operation modes, using bidirectional communications based on Information and Communication Technologies (ICT), it will be possible to exchange data between the EV driver and the future smart grids. This collaboration with the smart grids will strengthen...

  11. Development of near-term batteries for electric vehicles. Summary report, October 1977-September 1979

    Energy Technology Data Exchange (ETDEWEB)

    Rajan, J.B. (comp.)

    1980-06-01

    The status and results through FY 1979 on the Near-Term Electric Vehicle Battery Project of the Argonne National Laboratory are summarized. This project conducts R and D on lead-acid, nickel/zinc and nickel/iron batteries with the objective of achieving commercialization in electric vehicles in the 1980's. Key results of the R and D indicate major technology advancements and achievement of most of FY 1979 performance goals. In the lead-acid system the specific energy was increased from less than 30 Wh/kg to over 40 Wh/kg at the C/3 rate; the peak power density improved from 70 W/kg to over 110 W/kg at the 50% state of charge; and over 200 deep-discharge cycle life demonstrated. In the nickel/iron system a specific energy of 48 Wh/kg was achieved; a peak power of about 100 W/kg demonstrated and a life of 36 cycles obtained. In the nickel/zinc system, specific energies of up to 64 Wh/kg were shown; peak powers of 133 W/kg obtained; and a life of up to 120 cycles measured. Future R and D will emphasize increased cycle life for nickel/zinc batteries and increased cycle life and specific energy for lead-acid and nickel/iron batteries. Testing of 145 cells was completed by NBTL. Cell evaluation included a full set of performance tests plus the application of a simulated power profile equivalent to the power demands of an electric vehicle in stop-start urban driving. Simplified test profiles which approximate electric vehicle demands are also described.

  12. The Zebra Battery: a South African contender for electric vehicle application

    Directory of Open Access Journals (Sweden)

    J. Coertzer

    1996-07-01

    Full Text Available The Zebra battery is one of the most promising power sources for electric vehicles which might be on sale before the year 2000. It is a South African development which started at the CSIR and is at present jointly managed by the Anglo American Corpora­tion of S.A. and the German company A.E.G. The chemical reaction converts common salt and nickel to nickel chloride and sodium during the charging phase.

  13. Single-Phase PFC Converter for Plug-in Hybrid Electric Vehicle Battery Chargers

    OpenAIRE

    Shakil Ahamed Khan; Md. Ismail Hossain; Mousumi Aktar

    2012-01-01

    In this paper, a front end ac–dc power factor correction topology is proposed for plug-in hybrid electric vehicle (PHEV) battery charging. The topology can achieve improved power quality, in terms of power factor correction, reduced total harmonic distortion at input ac mains, and precisely regulated dc output. Within this context, this paper introduces a boost converter topology for implementing digital power factor correction based on low cost digital signal controller that operates the con...

  14. Analysing and evaluating a thermal management solution via heat pipes for lithium-ion batteries in electric vehicles

    OpenAIRE

    Wang, Qian

    2015-01-01

    Thermal management is crucial in many engineering applications because it affects the electrical, material, and other properties of the system. A recent study focuses on the use of heat pipes for battery thermal management in electric vehicles, which explores a new area for heat pipe applications. The battery, as one and only energy source in an EV, establishes a vital barrier for automotive industry because it can make the car more expensive and less reliable. The modelling methodology ...

  15. Optimizing battery sizes of plug-in hybrid and extended range electric vehicles for different user types

    OpenAIRE

    REDELBACH Martin; Özdemir, Enver Doruk; Friedrich, Horst E.

    2014-01-01

    There are ambitious greenhouse gas emissions (GHG) targets for the manufacturers of light duty vehicles. To reduce the GHG emissions, plug-in hybrid electric vehicle (PHEV) and extended range electric vehicle (EREV) are promising powertrain technologies. However, the battery is still a very critical component due to the high production cost and heavy weight. This paper introduces a holistic approach for the optimization of the battery size of PHEVs and EREVs under German market conditions. Th...

  16. Optimal recharging strategy for battery-switch stations for electric vehicles in France

    International Nuclear Information System (INIS)

    Most papers that study the recharging of electric vehicles focus on charging the batteries at home and at the work-place. The alternative is for owners to exchange the battery at a specially equipped battery switch station (BSS). This paper studies strategies for the BSS to buy and sell the electricity through the day-ahead market. We determine what the optimal strategies would have been for a large fleet of EVs in 2010 and 2011, for the V2G and the G2V cases. These give the amount that the BSS should offer to buy or sell each hour of the day. Given the size of the fleet, the quantities of electricity bought and sold will displace the market equilibrium. Using the aggregate offers to buy and the bids to sell on the day-ahead market, we compute what the new prices and volumes transacted would be. While buying electricity for the G2V case incurs a cost, it would have been possible to generate revenue in the V2G case, if the arrivals of the EVs had been evenly spaced during the day. Finally, we compare the total cost of implementing the strategies with the cost of buying the same quantity of electricity from EDF. - Highlights: • Optimal strategies for buying/selling electricity through day-ahead auction market. • Given fleet size power bought and sold would change market price and volume. • New prices computed using aggregate offers to buy/sell power in 2010 and 2011. • Timing of arrival of EVs critical in V2G case. If evenly spaced BSS makes money. • Strategies are very robust even when French and German markets were coupled Nov. 2010

  17. Salvá's Electric Telegraph based on Volta's Battery

    OpenAIRE

    Pérez Yuste, Antonio

    2009-01-01

    Contemporary of such important figures as d'Alembert, Buffon, Franklin, Kant, Betancourt or Goya, Francisco Salvá y Campillo was also a prominent Enlightenment scientist who shared with all of them his passion for knowledge and his support to the empiricism and to the scientific method. Five years before Samuel Thomas von Sömmering demonstrated his electro-chemical telegraph to the Munich Academy of Sciences, Salvá proposed a very innovative electric telegraph based on Volta’s pile, for gener...

  18. Experimental analysis on the performance of lithium based batteries for road full electric and hybrid vehicles

    International Nuclear Information System (INIS)

    Highlights: • Performance analysis for lithium storage technologies, such as Li[NiCoMn]O2 and LiFePO4 batteries. • Actual capacity of lithium technologies analyzed almost close to their nominal capacity also for high discharging current. • The charging efficiency for Li[NiCoMn]O2 positively affects the regenerative breaking and fast recharging operations. • The analyzed battery packs follow dynamic power requirements on performed road driving cycles. • Experimental results demonstrate driving range is much higher when battery packs are based on lithium technology. - Abstract: This paper deals with an experimental evaluation regarding the real performance of lithium based energy storage systems for automotive applications. In particular real working operations of different lithium based storage system technologies, such as Li[NiCoMn]O2 and LiFePO4 batteries, are compared in this work from the point of view of their application in supplying full electric and hybrid vehicles, taking as a reference the well-known behavior of lead acid batteries. For this purpose, the experimental tests carried out in laboratory are firstly performed on single storage modules in stationary conditions. In this case the related results are obtained by means of a bidirectional cycle tester based on the IGBT technology, and consent to evaluate, compare and contrast charge/discharge characteristics and efficiency at constant values of current/voltage/power for each storage technology analyzed. Then, lithium battery packs are tested in supplying a 1.8 kW electric power train using a laboratory test bench, based on a 48 V DC bus and specifically configured to simulate working operations of electric vehicles on the road. For this other experimentation the test bench is equipped with an electric brake and acquisition/control system, able to represent in laboratory the real vehicle conditions and road characteristics on predefined driving cycles at different slopes. The obtained

  19. Optimal operation strategy of battery energy storage system to real-time electricity price in Denmark

    DEFF Research Database (Denmark)

    Hu, Weihao; Chen, Zhe; Bak-Jensen, Birgitte

    2010-01-01

    Since the hourly spot market price is available one day ahead, the price could be transferred to the consumers and they may have some motivations to install an energy storage system in order to save their energy costs. This paper presents an optimal operation strategy for a battery energy storage...... system (BESS) in relation to the real-time electricity price in order to achieve the maximum profits of the BESS. The western Danish power system, which is currently the grid area in the world that has the largest share of wind power in its generation profiles and may represent the future of electricity...

  20. Optimizing battery sizes of plug-in hybrid and extended range electric vehicles for different user types

    International Nuclear Information System (INIS)

    There are ambitious greenhouse gas emission (GHG) targets for the manufacturers of light duty vehicles. To reduce the GHG emissions, plug-in hybrid electric vehicle (PHEV) and extended range electric vehicle (EREV) are promising powertrain technologies. However, the battery is still a very critical component due to the high production cost and heavy weight. This paper introduces a holistic approach for the optimization of the battery size of PHEVs and EREVs under German market conditions. The assessment focuses on the heterogeneity across drivers, by analyzing the impact of different driving profiles on the optimal battery setup from total cost of ownership (TCO) perspective. The results show that the battery size has a significant effect on the TCO. For an average German driver (15,000 km/a), battery capacities of 4 kWh (PHEV) and 6 kWh (EREV) would be cost optimal by 2020. However, these values vary strongly with the driving profile of the user. Moreover, the optimal battery size is also affected by external factors, e.g. electricity and fuel prices or battery production cost. Therefore, car manufacturers should develop a modular design for their batteries, which allows adapting the storage capacity to meet the individual customer requirements instead of “one size fits all”. - Highlights: • Optimization of the battery size of PHEVs and EREVs under German market conditions. • Focus on heterogeneity across drivers (e.g. mileage, trip distribution, speed). • Optimal battery size strongly depends on the driving profile and energy prices. • OEMs require a modular design for their batteries to meet individual requirements

  1. Lead-acid and lithium-ion batteries for the Chinese electric bike market and implications on future technology advancement

    Science.gov (United States)

    Weinert, Jonathan X.; Burke, Andrew F.; Wei, Xuezhe

    China has been experiencing a rapid increase in battery-powered personal transportation since the late 1990s due to the strong growth of the electric bike and scooter (i.e. e-bike) market. Annual sales in China reached 17 million bikes year -1 in 2006. E-bike growth has been in part due to improvements in rechargeable valve-regulated lead-acid (VRLA) battery technology, the primary battery type for e-bikes. Further improvements in technology and a transition from VRLA to lithium-ion (Li-ion) batteries will impact the future market growth of this transportation mode in China and abroad. Battery performance and cost for these two types are compared to assess the feasibility of a shift from VRLA to Li-ion battery e-bikes. The requirements for batteries used in e-bikes are assessed. A widespread shift from VRLA to Li-ion batteries seems improbable in the near future for the mass market given the cost premium relative to the performance advantages of Li-ion batteries. As both battery technologies gain more real-world use in e-bike applications, both will improve. Cell variability is a key problematic area to be addressed with VRLA technology. For Li-ion technology, safety and cost are the key problem areas which are being addressed through the use of new cathode materials.

  2. Adaptive unscented Kalman filtering for state of charge estimation of a lithium-ion battery for electric vehicles

    International Nuclear Information System (INIS)

    An accurate battery State of Charge estimation is of great significance for battery electric vehicles and hybrid electric vehicles. This paper presents an adaptive unscented Kalman filtering method to estimate State of Charge of a lithium-ion battery for battery electric vehicles. The adaptive adjustment of the noise covariances in the State of Charge estimation process is implemented by an idea of covariance matching in the unscented Kalman filter context. Experimental results indicate that the adaptive unscented Kalman filter-based algorithm has a good performance in estimating the battery State of Charge. A comparison with the adaptive extended Kalman filter, extended Kalman filter, and unscented Kalman filter-based algorithms shows that the proposed State of Charge estimation method has a better accuracy. -- Highlights: → Adaptive unscented Kalman filtering is proposed to estimate State of Charge of a lithium-ion battery for electric vehicles. → The proposed method has a good performance in estimating the battery State of Charge. → A comparison with three other Kalman filtering algorithms shows that the proposed method has a better accuracy.

  3. Long-term impacts of battery electric vehicles on the German electricity system

    Science.gov (United States)

    Heinrichs, H. U.; Jochem, P.

    2016-05-01

    The emerging market for electric vehicles gives rise to an additional electricity demand. This new electricity demand will affect the electricity system. For quantifying those impacts a model-based approach, which covers long-term time horizons is necessary in order to consider the long lasting investment paths in electricity systems and the market development of electric mobility. Therefore, we apply a bottom-up electricity system model showing a detailed spatial resolution for different development paths of electric mobility in Germany until 2030. This model is based on a linear optimization which minimizes the discounted costs of the electricity system. We observe an increase of electricity exchange between countries and electricity generated by renewable energy sources. One major result turns out to be that electric vehicles can be integrated in the electricity system without increasing the system costs when a controlled (postponing) charging strategy for electric vehicles is applied. The impact on the power plant portfolio is insignificant. Another important side effect of electric vehicles is their substantial contribution to decreasing CO2 emissions of the German transport sector. Hence, electric mobility might be an integral part of a sustainable energy system of tomorrow.

  4. A Novel Range-Extended Strategy for Fuel Cell/Battery Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Jenn-Jiang Hwang

    2015-01-01

    Full Text Available The range-extended electric vehicle is proposed to improve the range anxiety drivers have of electric vehicles. Conventionally, a gasoline/diesel generator increases the range of an electric vehicle. Due to the zero-CO2 emission stipulations, utilizing fuel cells as generators raises concerns in society. This paper presents a novel charging strategy for fuel cell/battery electric vehicles. In comparison to the conventional switch control, a fuzzy control approach is employed to enhance the battery’s state of charge (SOC. This approach improves the quick loss problem of the system’s SOC and thus can achieve an extended driving range. Smooth steering experience and range extension are the main indexes for development of fuzzy rules, which are mainly based on the energy management in the urban driving model. Evaluation of the entire control system is performed by simulation, which demonstrates its effectiveness and feasibility.

  5. Optimal Dispatch of Unreliable Electric Grid-Connected Diesel Generator-Battery Power Systems

    Science.gov (United States)

    Xu, D.; Kang, L.

    2015-06-01

    Diesel generator (DG)-battery power systems are often adopted by telecom operators, especially in semi-urban and rural areas of developing countries. Unreliable electric grids (UEG), which have frequent and lengthy outages, are peculiar to these regions. DG-UEG-battery power system is an important kind of hybrid power system. System dispatch is one of the key factors to hybrid power system integration. In this paper, the system dispatch of a DG-UEG-lead acid battery power system is studied with the UEG of relatively ample electricity in Central African Republic (CAR) and UEG of poor electricity in Congo Republic (CR). The mathematical models of the power system and the UEG are studied for completing the system operation simulation program. The net present cost (NPC) of the power system is the main evaluation index. The state of charge (SOC) set points and battery bank charging current are the optimization variables. For the UEG in CAR, the optimal dispatch solution is SOC start and stop points 0.4 and 0.5 that belong to the Micro-Cycling strategy and charging current 0.1 C. For the UEG in CR, the optimal dispatch solution is of 0.1 and 0.8 that belongs to the Cycle-Charging strategy and 0.1 C. Charging current 0.1 C is suitable for both grid scenarios compared to 0.2 C. It makes the dispatch strategy design easier in commercial practices that there are a few very good candidate dispatch solutions with system NPC values close to that of the optimal solution for both UEG scenarios in CAR and CR.

  6. Batteries charging systems for electric and plug-in hybrid electric vehicles

    OpenAIRE

    Monteiro, Vítor; Gonçalves, Henrique; João C. Ferreira; Afonso, João L.

    2012-01-01

    Many countries have a large dependence on imported fossil fuels whose prices increase almost every day. Knowing that much of this consumption is for transportation systems, it becomes essential to seek for alternatives. The natural bet is the electric mobility, namely through Electric Vehicles (EVs) and Plug-in Hybrid Electric Vehicles (PHEVs). However, the wide spread utilization of these vehicles has consequences on the electrical power grid, mainly in terms of load management and electric ...

  7. A novel active equalization method for lithium-ion batteries in electric vehicles

    International Nuclear Information System (INIS)

    Highlights: • Build an active equalization method for lithium-ion batteries. • A bidirectional transformer topology is introduced for active equalization. • The PF method is used for cell SOC estimation to eliminate drift noise of current. • The SOC based equalization algorithm is analyzed with different SOC bounds. - Abstract: Cell inconsistency is inevitable due to manufacturing constraint. Therefore, cell equalization is essentially required. In this paper, we propose a novel active equalization method based on the remaining capacity of cells which is feasible for lithium-ion battery packs in electric vehicles (EVs). The cell models are established based on a combined electrochemical model of lithium-ion batteries. The remaining capacity and state-of-charge (SOC) of cells are observed at the beginning of equalization. The particle filter (PF) method is employed to estimate the cell SOCs during equalization in order to eliminate the drift noise of the current sensor. The first high-SOC cell discharge (FHCD) and first low-SOC cell charge (FLCC) equalization algorithms are proposed and compared with 1% and 3% SOC bounds, respectively. The validation experiment results have shown that the proposed algorithm is suitable for equalization of lithium-ion batteries in EVs

  8. Fast Charging and Smart Charging Tests for Electric Vehicles Batteries Using Renewable Energy

    Directory of Open Access Journals (Sweden)

    Forero Camacho Oscar Mauricio

    2016-01-01

    Full Text Available Electric Vehicles (EV technologies are still relatively new and under strong development. Although some standardized solutions are being promoted and becoming a new trend, there is an outstanding need for common platforms and sharing of knowledge and core technologies. This paper presents the development of a test platform, including three Li-ion batteries designed for EV applications, and three associated bi-directional power converters, for testing impacts on different advanced loadings of EV batteries. Different charging algorithms/profiles have been tested, including constant current and power, and forced and pulsed power. The aim of the tests has been to study the impact of smart charging and fast charging on the power system, on the battery state of health and degradation, and to find out the limitations of the batteries for a Smart Grid. The paper outlines the advantages and disadvantages of both tests in terms of regulation of the aggregated local power, power capacity and the power exchange with the grid. The smart charging tests performed have demonstrated that even with a simple control algorithm, without any forecasting, it is possible to provide the required charging and at the same time the power system services, reducing the peak power and the energy losses in the power connection line of the power exchange with the national grid.

  9. Modelling Inductive Charging of Battery Electric Vehicles using an Agent-Based Approach

    Directory of Open Access Journals (Sweden)

    Zain Ul Abedin

    2014-09-01

    Full Text Available The introduction of battery electric vehicles (BEVs could help to reduce dependence on fossil fuels and emissions from transportation and as such increase energy security and foster sustainable use of energy resources. However a major barrier to the introduction of BEVs is their limited battery capacity and long charging durations. To address these issues of BEVs several solutions are proposed such as battery swapping and fast charging stations. However apart from these stationary modes of charging, recently a new mode of charging has been introduced which is called inductive charging. This allows charging of BEVs as they drive along roads without the need of plugs, using induction. But it is unclear, if and how such technology could be utilized best. In order to investigate the possible impact of the introduction of such inductive charging infrastructure, its potential and its optimal placement, a framework for simulating BEVs using a multi-agent transport simulation was used. This framework was extended by an inductive charging module and initial test runs were performed. In this paper we present the simulation results of these preliminary tests together with analysis which suggests that battery sizes of BEVs could be reduced even if inductive charging technology is implemented only at a small number of high traffic volume links. The paper also demonstrates that our model can effectively support policy and decision making for deploying inductive charging infrastructure.

  10. A Novel Data-Driven Fast Capacity Estimation of Spent Electric Vehicle Lithium-ion Batteries

    Directory of Open Access Journals (Sweden)

    Caiping Zhang

    2014-12-01

    Full Text Available Fast capacity estimation is a key enabling technique for second-life of lithium-ion batteries due to the hard work involved in determining the capacity of a large number of used electric vehicle (EV batteries. This paper tries to make three contributions to the existing literature through a robust and advanced algorithm: (1 a three layer back propagation artificial neural network (BP ANN model is developed to estimate the battery capacity. The model employs internal resistance expressing the battery’s kinetics as the model input, which can realize fast capacity estimation; (2 an estimation error model is established to investigate the relationship between the robustness coefficient and regression coefficient. It is revealed that commonly used ANN capacity estimation algorithm is flawed in providing robustness of parameter measurement uncertainties; (3 the law of large numbers is used as the basis for a proposed robust estimation approach, which optimally balances the relationship between estimation accuracy and disturbance rejection. An optimal range of the threshold for robustness coefficient is also discussed and proposed. Experimental results demonstrate the efficacy and the robustness of the BP ANN model together with the proposed identification approach, which can provide an important basis for large scale applications of second-life of batteries.

  11. Overcoming the Range Limitation of Medium-Duty Battery Electric Vehicles through the use of Hydrogen Fuel-Cells

    Energy Technology Data Exchange (ETDEWEB)

    Wood, E.; Wang, L.; Gonder, J.; Ulsh, M.

    2013-10-01

    Battery electric vehicles possess great potential for decreasing lifecycle costs in medium-duty applications, a market segment currently dominated by internal combustion technology. Characterized by frequent repetition of similar routes and daily return to a central depot, medium-duty vocations are well positioned to leverage the low operating costs of battery electric vehicles. Unfortunately, the range limitation of commercially available battery electric vehicles acts as a barrier to widespread adoption. This paper describes the National Renewable Energy Laboratory's collaboration with the U.S. Department of Energy and industry partners to analyze the use of small hydrogen fuel-cell stacks to extend the range of battery electric vehicles as a means of improving utility, and presumably, increasing market adoption. This analysis employs real-world vocational data and near-term economic assumptions to (1) identify optimal component configurations for minimizing lifecycle costs, (2) benchmark economic performance relative to both battery electric and conventional powertrains, and (3) understand how the optimal design and its competitiveness change with respect to duty cycle and economic climate. It is found that small fuel-cell power units provide extended range at significantly lower capital and lifecycle costs than additional battery capacity alone. And while fuel-cell range-extended vehicles are not deemed economically competitive with conventional vehicles given present-day economic conditions, this paper identifies potential future scenarios where cost equivalency is achieved.

  12. Development and Implementation of a Battery-Electric Light-Duty Class 2a Truck including Hybrid Energy Storage

    Science.gov (United States)

    Kollmeyer, Phillip J.

    This dissertation addresses two major related research topics: 1) the design, fabrication, modeling, and experimental testing of a battery-electric light-duty Class 2a truck; and 2) the design and evaluation of a hybrid energy storage system (HESS) for this and other vehicles. The work begins with the determination of the truck's peak power and wheel torque requirements (135kW/4900Nm). An electric traction system is then designed that consists of an interior permanent magnet synchronous machine, two-speed gearbox, three-phase motor drive, and LiFePO4 battery pack. The battery pack capacity is selected to achieve a driving range similar to the 2011 Nissan Leaf electric vehicle (73 miles). Next, the demonstrator electric traction system is built and installed in the vehicle, a Ford F150 pickup truck, and an extensive set of sensors and data acquisition equipment is installed. Detailed loss models of the battery pack, electric traction machine, and motor drive are developed and experimentally verified using the driving data. Many aspects of the truck's performance are investigated, including efficiency differences between the two-gear configuration and the optimal gear selection. The remainder focuses on the application of battery/ultracapacitor hybrid energy storage systems (HESS) to electric vehicles. First, the electric truck is modeled with the addition of an ultracapacitor pack and a dc/dc converter. Rule-based and optimal battery/ultracapacitor power-split control algorithms are then developed, and the performance improvements achieved for both algorithms are evaluated for operation at 25°C. The HESS modeling is then extended to low temperatures, where battery resistance increases substantially. To verify the accuracy of the model-predicted results, a scaled hybrid energy storage system is built and the system is tested for several drive cycles and for two temperatures. The HESS performance is then modeled for three variants of the vehicle design, including the

  13. Utilizing a vanadium redox flow battery to avoid wind power deviation penalties in an electricity market

    International Nuclear Information System (INIS)

    Highlights: • Vanadium redox flow battery utilized for wind power grid integration was studied. • Technical and financial analyses at single wind farm level were performed. • 2 MW/6 MW h VRFB is suitable for mitigating power deviations for a 10 MW wind farm. • Economic incentives might be required in the short-term until the VRFB prices drop. - Abstract: Utilizing a vanadium redox flow battery (VRFB) for better market integration of wind power at a single wind farm level was evaluated. A model which combines a VRFB unit and a medium sized (10 MW) wind farm was developed and the battery was utilized to compensate for the deviations resulting from the forecast errors in an electricity market bidding structure. VRFB software model which was introduced in our previous paper was integrated with real wind power data, power forecasts and market data based on the Spanish electricity market. Economy of the system was evaluated by financial assessments which were done by considering the VRFB costs and the amount of deviation penalty payments resulting from forecast inaccuracies

  14. State of Charge Estimation Based on Microscopic Driving Parameters for Electric Vehicle's Battery

    Directory of Open Access Journals (Sweden)

    Enjian Yao

    2013-01-01

    Full Text Available Recently, battery-powered electric vehicle (EV has received wide attention due to less pollution during use, low noise, and high energy efficiency and is highly expected to improve urban air quality and then mitigate energy and environmental pressure. However, the widespread use of EV is still hindered by limited battery capacity and relatively short cruising range. This paper aims to propose a state of charge (SOC estimation method for EV’s battery necessary for route planning and dynamic route guidance, which can help EV drivers to search for the optimal energy-efficient routes and to reduce the risk of running out of electricity before arriving at the destination or charging station. Firstly, by analyzing the variation characteristics of power consumption rate with initial SOC and microscopic driving parameters (instantaneous speed and acceleration, a set of energy consumption rate models are established according to different operation modes. Then, the SOC estimation model is proposed based on the presented EV power consumption model. Finally, by comparing the estimated SOC with the measured SOC, the proposed SOC estimation method is proved to be highly accurate and effective, which can be well used in EV route planning and navigation systems.

  15. A Thermally-Regenerative Ammonia-Based Flow Battery for Electrical Energy Recovery from Waste Heat.

    Science.gov (United States)

    Zhu, Xiuping; Rahimi, Mohammad; Gorski, Christopher A; Logan, Bruce

    2016-04-21

    Large amounts of low-grade waste heat (temperatures geothermal, and solar-based processes. Using thermally-regenerative ammonia solutions, low-grade thermal energy can be converted to electricity in battery systems. To improve reactor efficiency, a compact, ammonia-based flow battery (AFB) was developed and tested at different solution concentrations, flow rates, cell pairs, and circuit connections. The AFB achieved a maximum power density of 45 W m(-2) (15 kW m(-3) ) and an energy density of 1260 Wh manolyte (-3) , with a thermal energy efficiency of 0.7 % (5 % relative to the Carnot efficiency). The power and energy densities of the AFB were greater than those previously reported for thermoelectrochemical and salinity-gradient technologies, and the voltage or current could be increased using stacked cells. These results demonstrated that an ammonia-based flow battery is a promising technology to convert low-grade thermal energy to electricity.

  16. A Novel Series Connected Batteries State of High Voltage Safety Monitor System for Electric Vehicle Application

    Directory of Open Access Journals (Sweden)

    Qiang Jiaxi

    2013-01-01

    Full Text Available Batteries, as the main or assistant power source of EV (Electric Vehicle, are usually connected in series with high voltage to improve the drivability and energy efficiency. Today, more and more batteries are connected in series with high voltage, if there is any fault in high voltage system (HVS, the consequence is serious and dangerous. Therefore, it is necessary to monitor the electric parameters of HVS to ensure the high voltage safety and protect personal safety. In this study, a high voltage safety monitor system is developed to solve this critical issue. Four key electric parameters including precharge, contact resistance, insulation resistance, and remaining capacity are monitored and analyzed based on the equivalent models presented in this study. The high voltage safety controller which integrates the equivalent models and control strategy is developed. By the help of hardware-in-loop system, the equivalent models integrated in the high voltage safety controller are validated, and the online electric parameters monitor strategy is analyzed and discussed. The test results indicate that the high voltage safety monitor system designed in this paper is suitable for EV application.

  17. Technical and legal considerations and solutions in the area of battery charging for electric vehicles

    Science.gov (United States)

    Juda, Z.

    2016-09-01

    The issue of protecting health of residents of urbanized areas from the effect of excessive particulate matter and toxic components of car exhaust gases imposes the need of introduction of clean electric vehicles to the market. The increasing market availability of electric vehicles, especially in the segment of short-range (neighborhood) vehicles is followed by development of new and advanced infrastructure solutions. This also applies to the increasingly popular hybrid vehicles PHEV (Plug-in Hybrid Electric Vehicles). However, problems with the existing designs are primarily associated with limited driving range on a single battery charge, the density of charging stations in urban and suburban area, energy system efficiency due to increased electricity demand and the unification of solutions for charging stations, on-board chargers and the necessary accessories. Technical solutions are dependent on many factors, including the type and size of battery in the vehicle and access to power grid with increased load capacity. The article discusses the legal and technical actions outlined in the above directions. It shows the available and planned solutions in this area.

  18. Improved SCR ac Motor Controller for Battery Powered Urban Electric Vehicles

    Science.gov (United States)

    Latos, T. S.

    1982-01-01

    An improved ac motor controller, which when coupled to a standard ac induction motor and a dc propulsion battery would provide a complete electric vehicle power train with the exception of the mechanical transmission and drive wheels was designed. In such a system, the motor controller converts the dc electrical power available at the battery terminals to ac electrical power for the induction motor in response to the drivers commands. The performance requirements of a hypothetical electric vehicle with an upper weight bound of 1590 kg (3500 lb) were used to determine the power rating of the controller. Vehicle acceleration capability, top speed, and gradeability requisites were contained in the Society of Automotive Engineers (SAE) Schedule 227a(d) driving cycle. The important capabilities contained in this driving cycle are a vehicle acceleration requirement of 0 to 72.4 kmph (0 to 45 mph) in 28 seconds a top speed of 88.5 kmph (55 mph), and the ability to negotiate a 10% grade at 48 kmph (30 mph). A 10% grade is defined as one foot of vertical rise per 10 feet of horizontal distance.

  19. Directly connected series coupled HTPEM fuel cell stacks to a Li-ion battery DC bus for a fuel cell electrical vehicle

    DEFF Research Database (Denmark)

    Andreasen, Søren Juhl; Ashworth, Leanne; Remón, Ian Natanael;

    2008-01-01

    The work presented in this paper examines the use of pure hydrogen fuelled high temperature polymer electrolyte membrane (HTPEM) fuel cell stacks in an electrical car, charging a Li-ion battery pack. The car is equipped with two branches of two series coupled 1 kW fuel cell stacks which...... are connected directly parallel to the battery pack during operation. This enables efficient charging of the batteries for increased driving range. With no power electronics used, the fuel cell stacks follow the battery pack voltage, and charge the batteries passively. This saves the electrical and economical...... losses related to these components and their added system complexity. The new car battery pack consists of 23 Li-ion battery cells and the charging and discharging are monitored by a battery management system (BMS) which ensures safe operating conditions for the batteries. The direct connection...

  20. Energy management strategy for a parallel hybrid electric vehicle equipped with a battery/ultra-capacitor hybrid energy storage system

    Institute of Scientific and Technical Information of China (English)

    Jun-yi LIANG; Jian-long ZHANG; Xi ZHANG; Shi-fei YUAN; Cheng-liang YIN

    2013-01-01

    To solve the low power density issue of hybrid electric vehicular batteries,a combination of batteries and ultracapacitors(UCs)could be a solution.The high power density feature of UCs can improve the performance of battery/UC hybrid energy storage systems(HESSs).This paper presents a parallel hybrid electric vehicle(HEV)equipped with an internal combustion engine and an HESS.An advanced energy management strategy(EMS),mainly based on fuzzy logic,is proposed to improve the fuel economy of the HEV and the endurance of the HESS.The EMS is capable of determining the ideal distribution of output power among the internal combustion engine,battery,and UC according to the propelling power or regenerative braking power of the vehicle.To validate the effectiveness of the EMS,numerical simulation and experimental validations are carried out.The results indicate that EMS can effectively control the power sources to work within their respective efficient areas.The battery load can be mitigated and prolonged battery life can be expected.The electrical energy consumption in the HESS is reduced by 3.91%compared with that in the battery only system.Fuel consumption of the HEV is reduced by 24.3% compared with that of the same class conventional vehicles under Economic Commission of Europe driving cycle.

  1. Study on the Optimal Charging Strategy for Lithium-Ion Batteries Used in Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Shuo Zhang

    2014-10-01

    Full Text Available The charging method of lithium-ion batteries used in electric vehicles (EVs significantly affects its commercial application. This paper aims to make three contributions to the existing literature. (1 In order to achieve an efficient charging strategy for lithium-ion batteries with shorter charging time and lower charring loss, the trade-off problem between charging loss and charging time has been analyzed in details through the dynamic programing (DP optimization algorithm; (2 To reduce the computation time consumed during the optimization process, we have proposed a database based optimization approach. After off-line calculation, the simulation results can be applied to on-line charge; (3 The novel database-based DP method is proposed and the simulation results illustrate that this method can effectively find the suboptimal charging strategies under a certain balance between the charging loss and charging time.

  2. Current status of environmental, health, and safety issues of lithium ion electric vehicle batteries

    Energy Technology Data Exchange (ETDEWEB)

    Vimmerstedt, L.J.; Ring, S.; Hammel, C.J.

    1995-09-01

    The lithium ion system considered in this report uses lithium intercalation compounds as both positive and negative electrodes and has an organic liquid electrolyte. Oxides of nickel, cobalt, and manganese are used in the positive electrode, and carbon is used in the negative electrode. This report presents health and safety issues, environmental issues, and shipping requirements for lithium ion electric vehicle (EV) batteries. A lithium-based electrochemical system can, in theory, achieve higher energy density than systems using other elements. The lithium ion system is less reactive and more reliable than present lithium metal systems and has possible performance advantages over some lithium solid polymer electrolyte batteries. However, the possibility of electrolyte spills could be a disadvantage of a liquid electrolyte system compared to a solid electrolyte. The lithium ion system is a developing technology, so there is some uncertainty regarding which materials will be used in an EV-sized battery. This report reviews the materials presented in the open literature within the context of health and safety issues, considering intrinsic material hazards, mitigation of material hazards, and safety testing. Some possible lithium ion battery materials are toxic, carcinogenic, or could undergo chemical reactions that produce hazardous heat or gases. Toxic materials include lithium compounds, nickel compounds, arsenic compounds, and dimethoxyethane. Carcinogenic materials include nickel compounds, arsenic compounds, and (possibly) cobalt compounds, copper, and polypropylene. Lithiated negative electrode materials could be reactive. However, because information about the exact compounds that will be used in future batteries is proprietary, ongoing research will determine which specific hazards will apply.

  3. Materials Challenges and Opportunities of Lithium-ion Batteries for Electrical Energy Storage

    Science.gov (United States)

    Manthiram, Arumugam

    2011-03-01

    Electrical energy storage has emerged as a topic of national and global importance with respect to establishing a cleaner environment and reducing the dependence on foreign oil. Batteries are the prime candidates for electrical energy storage. They are the most viable near-term option for vehicle applications and the efficient utilization of intermittent energy sources like solar and wind. Lithium-ion batteries are attractive for these applications as they offer much higher energy density than other rechargeable battery systems. However, the adoption of lithium-ion battery technology for vehicle and stationary storage applications is hampered by high cost, safety concerns, and limitations in energy, power, and cycle life, which are in turn linked to severe materials challenges. This presentation, after providing an overview of the current status, will focus on the physics and chemistry of new materials that can address these challenges. Specifically, it will focus on the design and development of (i) high-capacity, high-voltage layered oxide cathodes, (ii) high-voltage, high-power spinel oxide cathodes, (iii) high-capacity silicate cathodes, and (iv) nano-engineered, high-capacity alloy anodes. With high-voltage cathodes, a critical issue is the instability of the electrolyte in contact with the highly oxidized cathode surface and the formation of solid-electrolyte interfacial (SEI) layers that degrade the performance. Accordingly, surface modification of cathodes with nanostructured materials and self-surface segregation during the synthesis process to suppress SEI layer formation and enhance the energy, power, and cycle life will be emphasized. With the high-capacity alloy anodes, a critical issue is the huge volume change occurring during the charge-discharge process and the consequent poor cycle life. Dispersion of the active alloy nanoparticles in an inactive metal oxide-carbon matrix to mitigate this problem and realize long cycle life will be presented.

  4. Development of Low Cost Carbonaceous Materials for Anodes in Lithium-Ion Batteries for Electric and Hybrid Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Barsukov, Igor V.

    2002-12-10

    Final report on the US DOE CARAT program describes innovative R & D conducted by Superior Graphite Co., Chicago, IL, USA in cooperation with researchers from the Illinois Institute of Technology, and defines the proper type of carbon and a cost effective method for its production, as well as establishes a US based manufacturer for the application of anodes of the Lithium-Ion, Lithium polymer batteries of the Hybrid Electric and Pure Electric Vehicles. The three materials each representing a separate class of graphitic carbon, have been developed and released for field trials. They include natural purified flake graphite, purified vein graphite and a graphitized synthetic carbon. Screening of the available on the market materials, which will help fully utilize the graphite, has been carried out.

  5. Large-Scale Battery System Development and User-Specific Driving Behavior Analysis for Emerging Electric-Drive Vehicles

    Directory of Open Access Journals (Sweden)

    Yihe Sun

    2011-04-01

    Full Text Available Emerging green-energy transportation, such as hybrid electric vehicles (HEVs and plug-in HEVs (PHEVs, has a great potential for reduction of fuel consumption and greenhouse emissions. The lithium-ion battery system used in these vehicles, however, is bulky, expensive and unreliable, and has been the primary roadblock for transportation electrification. Meanwhile, few studies have considered user-specific driving behavior and its significant impact on (PHEV fuel efficiency, battery system lifetime, and the environment. This paper presents a detailed investigation of battery system modeling and real-world user-specific driving behavior analysis for emerging electric-drive vehicles. The proposed model is fast to compute and accurate for analyzing battery system run-time and long-term cycle life with a focus on temperature dependent battery system capacity fading and variation. The proposed solution is validated against physical measurement using real-world user driving studies, and has been adopted to facilitate battery system design and optimization. Using the collected real-world hybrid vehicle and run-time driving data, we have also conducted detailed analytical studies of users’ specific driving patterns and their impacts on hybrid vehicle electric energy and fuel efficiency. This work provides a solid foundation for future energy control with emerging electric-drive applications.

  6. Coordinated Control Scheme of Battery Energy Storage System (BESS) and Distributed Generations (DGs) for Electric Distribution Grid Operation

    DEFF Research Database (Denmark)

    Cha, Seung-Tae; Zhao, Haoran; Wu, Qiuwei;

    2012-01-01

    This paper describes a coordinated control scheme of battery energy storage system (BESS) and distributed generations (DGs) for electric distribution grid operation. The BESS is designed to stabilize frequency and voltages as a primary control after the electric distribution system enters...

  7. Research, development, and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report for 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    Progress in the development of nickel-zinc batteries for electric vehicles is reported. Information is presented on nickel electrode preparation and testing; zinc electrode preparation with additives and test results; separator development and the evaluation of polymer-blend separator films; sealed Ni-Zn cells; and the optimization of electric vehicle-type Ni-Zn cells. (LCL)

  8. The processing of accumulator materials. Study on the environmental burden of batteries for electric and hybrid cars

    International Nuclear Information System (INIS)

    Batteries in electric-powered vehicles and hybrid systems contain a large amount of heavy metals and other toxic materials. An overview is given of health aspects and regulations with respect to such batteries. Also the state of the art of collecting, processing and recovering battery materials is given. It is concluded that, as a result of the accurate collecting system for lead-acid batteries and the development of environment-friendly types of accumulators, there are no significant environmental and health problems to be expected in the next few years. This study resulted in some recommendations by means of which the environmental burden of different types of batteries can be further reduced. 20 refs

  9. A cost effective battery bank for I(sup 2)T testing and evaluation of electrical switchgear

    Science.gov (United States)

    Reass, W. A.

    The electrical design and mechanical construction of a 50 kA step switched battery bank. Individual fuses protect each of the forty parallel isolated strings of three series (12 V) batteries. Step current waveforms of 12.5 kA, 25 kA, 37.5 kA, and 50 kA are produced by 8 sets of pneumatically driven 20 pole step switches and current limiting stainless steel trombone resistors. Inexpensive, yet conservatively designed, Group 65 Motorcraft car batteries are used to give an I(sup 2)t capability of better than 5 x 10(exp 9). The battery bank has well over 1500 shots, with testing of commercial switchgear continuing. In addition to the battery bank engineering data, results of repetitive testing of vacuum interrupters at their I(sup 2)t limit will be provided.

  10. Development and Characterization of an Electrically Rechargeable Zinc-Air Battery Stack

    OpenAIRE

    Hongyun Ma; Baoguo Wang; Yongsheng Fan; Weichen Hong

    2014-01-01

    An electrically rechargeable zinc-air battery stack consisting of three single cells in series was designed using a novel structured bipolar plate with air-breathing holes. Alpha-MnO 2 and LaNiO 3 severed as the catalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). The anodic and cathodic polarization and individual cell voltages were measured at constant charge-discharge (C-D) current densities indicating a uniform voltage profile for each single cell. One hu...

  11. Secondary Re-Use of Batteries From Electric Vehicles for Building Integrated Photo-Voltaic (BIPV) applications

    OpenAIRE

    McLoughlin, Fintan; Conlon, Michael

    2015-01-01

    PV Crops is evaluating the use of battery technologies such as Vanadium Redox within Building Integrated Photovoltaic (BIPV) applications. However, their inclusion into BIPV systems will inevitably raise the overall costs of such systems. As a result, PV Crops is looking at other measures in parallel to help lower the costs associated with such systems. One particular area of interest is the potential secondary re-use of battery technology from Electric Vehicle (EV) market as a way of mitigat...

  12. Implementation and in-depth analyses of a battery-supercapacitor powered electric vehicle (E-Kancil)

    OpenAIRE

    Embrandiri, Manoj

    2014-01-01

    This thesis contributes to the research issue pertaining to the management of multiple energy sources on-board a pure electric vehicle; particularly the energy dense traction battery and the power dense supercapacitor or ultracapacitor. This is achieved by analysing real world drive data on the interaction between lead acid battery pack and supercapacitor module connected in parallel while trying to fulfil the load demands of the vehicle. The initial findings and performance of a prototype...

  13. Large-Scale Battery System Development and User-Specific Driving Behavior Analysis for Emerging Electric-Drive Vehicles

    OpenAIRE

    Yihe Sun; Li Shang; Qin Lv; Kun Li; Yifei Jiang; Jie Wu,

    2011-01-01

    Emerging green-energy transportation, such as hybrid electric vehicles (HEVs) and plug-in HEVs (PHEVs), has a great potential for reduction of fuel consumption and greenhouse emissions. The lithium-ion battery system used in these vehicles, however, is bulky, expensive and unreliable, and has been the primary roadblock for transportation electrification. Meanwhile, few studies have considered user-specific driving behavior and its significant impact on (P)HEV fuel efficiency, battery system l...

  14. Prediction of thermal behaviors of an air-cooled lithium-ion battery system for hybrid electric vehicles

    Science.gov (United States)

    Choi, Yong Seok; Kang, Dal Mo

    2014-12-01

    Thermal management has been one of the major issues in developing a lithium-ion (Li-ion) hybrid electric vehicle (HEV) battery system since the Li-ion battery is vulnerable to excessive heat load under abnormal or severe operational conditions. In this work, in order to design a suitable thermal management system, a simple modeling methodology describing thermal behavior of an air-cooled Li-ion battery system was proposed from vehicle components designer's point of view. A proposed mathematical model was constructed based on the battery's electrical and mechanical properties. Also, validation test results for the Li-ion battery system were presented. A pulse current duty and an adjusted US06 current cycle for a two-mode HEV system were used to validate the accuracy of the model prediction. Results showed that the present model can give good estimations for simulating convective heat transfer cooling during battery operation. The developed thermal model is useful in structuring the flow system and determining the appropriate cooling capacity for a specified design prerequisite of the battery system.

  15. Multi-functional Converter with Integrated Motor Control, Battery Charging and Active Module Balancing for Electric Vehicular Application

    DEFF Research Database (Denmark)

    Mathe, Laszlo; Schaltz, Erik; Teodorescu, Remus;

    2014-01-01

    In order to reduce the fuel consumption and the acoustical noise generated by refuse lorries, electrification of the waste compactor unit is a very promising solution. For the electrical energy storage Lithium-Sulfur (Li-S) battery technology has been selected with potential for reducing the cost...... used successfully in HVDC/FACTS and large drive applications. In this paper the use of MMC for a battery driven waste compactor unit addressed with integrated functionality including: motor driver, battery charge and active balancing is presented. The challenges addressed here are related to the design...

  16. Laboratory facility for testing electric-vehicle batteries Test rig for simulating duty cycles with different discharge modes

    Science.gov (United States)

    Hamilton, J. A.; Rand, D. A. J.

    1983-03-01

    A test rig has been designed and constructed to examine the performance of batteries under laboratory conditions that simulate the power characteristics of electric vehicles. Each station in the rig subjects a battery to continuous charge/discharge cycles, with an equalising charge every eighth cycle. The battery discharge follows the current-verse-time profile of a given vehicle operating under a driving schedule normal to road service. The test rig allows both smooth- and pulsed-current discharge to be investigated. Data collection is accomplished either with multi-pen recorders or with a computer-based information logger.

  17. Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

    DEFF Research Database (Denmark)

    Nielsen, L.H.; Jørgensen K.

    2000-01-01

    The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore toillustrate the potential synergistic interplay...... between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalisedelectricity market are analysed. The project focuses on battery electric vehicles and fuel cell...... vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and forthe conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport...

  18. The computer simulation of automobile use patterns for defining battery requirements for electric cars

    Science.gov (United States)

    Schwartz, H. J.

    1976-01-01

    A Monte Carlo simulation process was used to develop the U.S. daily range requirements for an electric vehicle from probability distributions of trip lengths and frequencies and average annual mileage data. The analysis shows that a car in the U.S. with a practical daily range of 82 miles (132 km) can meet the needs of the owner on 95% of the days of the year, or at all times other than his long vacation trips. Increasing the range of the vehicle beyond this point will not make it more useful to the owner because it will still not provide intercity transportation. A daily range of 82 miles can be provided by an intermediate battery technology level characterized by an energy density of 30 to 50 watt-hours per pound (66 to 110 W-hr/kg). Candidate batteries in this class are nickel-zinc, nickel-iron, and iron-air. The implication of these results for the research goals of far-term battery systems suggests a shift in emphasis toward lower cost and greater life and away from high energy density.

  19. The computer simulation of automobile use patterns for defining battery requirements for electric cars

    Science.gov (United States)

    Schwartz, H.-J.

    1976-01-01

    The modeling process of a complex system, based on the calculation and optimization of the system parameters, is complicated in that some parameters can be expressed only as probability distributions. In the present paper, a Monte Carlo technique was used to determine the daily range requirements of an electric road vehicle in the United States from probability distributions of trip lengths, frequencies, and average annual mileage data. The analysis shows that a daily range of 82 miles meets to 95% of the car-owner requirements at all times with the exception of long vacation trips. Further, it is shown that the requirement of a daily range of 82 miles can be met by a (intermediate-level) battery technology characterized by an energy density of 30 to 50 Watt-hours per pound. Candidate batteries in this class are nickel-zinc, nickel-iron, and iron-air. These results imply that long-term research goals for battery systems should be focused on lower cost and longer service life, rather than on higher energy densities

  20. Dynamic thermal characteristics of heat pipe via segmented thermal resistance model for electric vehicle battery cooling

    Science.gov (United States)

    Liu, Feifei; Lan, Fengchong; Chen, Jiqing

    2016-07-01

    Heat pipe cooling for battery thermal management systems (BTMSs) in electric vehicles (EVs) is growing due to its advantages of high cooling efficiency, compact structure and flexible geometry. Considering the transient conduction, phase change and uncertain thermal conditions in a heat pipe, it is challenging to obtain the dynamic thermal characteristics accurately in such complex heat and mass transfer process. In this paper, a "segmented" thermal resistance model of a heat pipe is proposed based on thermal circuit method. The equivalent conductivities of different segments, viz. the evaporator and condenser of pipe, are used to determine their own thermal parameters and conditions integrated into the thermal model of battery for a complete three-dimensional (3D) computational fluid dynamics (CFD) simulation. The proposed "segmented" model shows more precise than the "non-segmented" model by the comparison of simulated and experimental temperature distribution and variation of an ultra-thin micro heat pipe (UMHP) battery pack, and has less calculation error to obtain dynamic thermal behavior for exact thermal design, management and control of heat pipe BTMSs. Using the "segmented" model, the cooling effect of the UMHP pack with different natural/forced convection and arrangements is predicted, and the results correspond well to the tests.

  1. Effect of extreme temperatures on battery charging and performance of electric vehicles

    Science.gov (United States)

    Lindgren, Juuso; Lund, Peter D.

    2016-10-01

    Extreme temperatures pose several limitations to electric vehicle (EV) performance and charging. To investigate these effects, we combine a hybrid artificial neural network-empirical Li-ion battery model with a lumped capacitance EV thermal model to study how temperature will affect the performance of an EV fleet. We find that at -10 °C, the self-weighted mean battery charging power (SWMCP) decreases by 15% compared to standard 20 °C temperature. Active battery thermal management (BTM) during parking can improve SWMCP for individual vehicles, especially if vehicles are charged both at home and at workplace; the median SWMCP is increased by over 30%. Efficiency (km/kWh) of the vehicle fleet is maximized when ambient temperature is close to 20 °C. At low (-10 °C) and high (+40 °C) ambient temperatures, cabin preconditioning and BTM during parking can improve the median efficiency by 8% and 9%, respectively. At -10 °C, preconditioning and BTM during parking can also improve the fleet SOC by 3-6%-units, but this also introduces a "base" load of around 140 W per vehicle. Finally, we observe that the utility of the fleet can be increased by 5%-units by adding 3.6 kW chargers to workplaces, but further improved charging infrastructure would bring little additional benefit.

  2. The performance and efficiency of four motor/controller/battery systems for the simpler electric vehicles

    Science.gov (United States)

    Shipps, P. R.

    1980-01-01

    A test and analysis program performed on four complete propulsion systems for an urban electric vehicle (EV) is described and results given. A dc series motor and a permanent magnet (PM) motor were tested, each powered by an EV battery pack and controlled by (1) a series/parallel voltage-switching (V-switch) system; and (2) a system using a pulse width modulation, 400 Hz transistorized chopper. Dynamometer tests were first performed, followed by eV performance predictions and data correlating road tests. During dynamometer tests using chopper control; current, voltage, and power were measured on both the battery and motor sides of the chopper, using three types of instrumentation. Conventional dc instruments provided adequate accuracy for eV power and energy measurements, when used on the battery side of the controller. When using the chopper controller, the addition of a small choke inductor improved system efficiency in the lower duty cycle range (some 8% increase at 50% duty cycle) with both types of motors. Overall system efficiency rankings during road tests were: (1) series motor with V-switch; (2) PM motor with V-switch; (3) series motor with chopper; and (4) PM motor with chopper. Chopper control of the eV was smoother and required less driver skill than V-switch control.

  3. The performance and efficiency of four motor/controller/battery systems for the simpler electric vehicles

    Science.gov (United States)

    Shipps, P. R.

    1980-05-01

    A test and analysis program performed on four complete propulsion systems for an urban electric vehicle (EV) is described and results given. A dc series motor and a permanent magnet (PM) motor were tested, each powered by an EV battery pack and controlled by (1) a series/parallel voltage-switching (V-switch) system; and (2) a system using a pulse width modulation, 400 Hz transistorized chopper. Dynamometer tests were first performed, followed by eV performance predictions and data correlating road tests. During dynamometer tests using chopper control; current, voltage, and power were measured on both the battery and motor sides of the chopper, using three types of instrumentation. Conventional dc instruments provided adequate accuracy for eV power and energy measurements, when used on the battery side of the controller. When using the chopper controller, the addition of a small choke inductor improved system efficiency in the lower duty cycle range (some 8% increase at 50% duty cycle) with both types of motors. Overall system efficiency rankings during road tests were: (1) series motor with V-switch; (2) PM motor with V-switch; (3) series motor with chopper; and (4) PM motor with chopper. Chopper control of the eV was smoother and required less driver skill than V-switch control.

  4. Thermal management of cylindrical power battery module for extending the life of new energy electric vehicles

    International Nuclear Information System (INIS)

    Thermal management especially cooling plays an important role in power battery modules for electric vehicles. In order to comprehensively understand the heat transfer characteristics of air cooling system, the air cooling numerical simulation battery models for cylindrical lithium-ion power battery pack were established in this paper, and a detailed parametric investigation was undertaken to study effects of different ventilation types and velocities, gap spacing between neighbor batteries, temperatures of environment and entrance air, amount of single row cells and battery diameter on the thermal management performance of battery pack. The results showed that the local temperature difference increased firstly and then decreased with the increase of wind speed. Reversing the air flow direction between adjacent rows is not necessarily appropriate and the gap spacing should not be too small and too large. It is prone to thermal runaway when the ambient temperature is too high, and the most suitable value of S/D (the ratio of spacing distance between neighbor cells and cell diameter) is gradually reduced along with the increase of cell diameter. - Highlights: • Air cooling models were established for cylindrical lithium-ion power battery pack. • Local temperature difference increased firstly and then decreased with wind speed. • The gap spacing size of battery pack should not be too small and too large. • It is prone to thermal runaway when the ambient temperature is too high. • The ratio of S/D is gradually reduced with the increase of cell diameter

  5. A novel methodology for non-linear system identification of battery cells used in non-road hybrid electric vehicles

    Science.gov (United States)

    Unger, Johannes; Hametner, Christoph; Jakubek, Stefan; Quasthoff, Marcus

    2014-12-01

    An accurate state of charge (SoC) estimation of a traction battery in hybrid electric non-road vehicles, which possess higher dynamics and power densities than on-road vehicles, requires a precise battery cell terminal voltage model. This paper presents a novel methodology for non-linear system identification of battery cells to obtain precise battery models. The methodology comprises the architecture of local model networks (LMN) and optimal model based design of experiments (DoE). Three main novelties are proposed: 1) Optimal model based DoE, which aims to high dynamically excite the battery cells at load ranges frequently used in operation. 2) The integration of corresponding inputs in the LMN to regard the non-linearities SoC, relaxation, hysteresis as well as temperature effects. 3) Enhancements to the local linear model tree (LOLIMOT) construction algorithm, to achieve a physical appropriate interpretation of the LMN. The framework is applicable for different battery cell chemistries and different temperatures, and is real time capable, which is shown on an industrial PC. The accuracy of the obtained non-linear battery model is demonstrated on cells with different chemistries and temperatures. The results show significant improvement due to optimal experiment design and integration of the battery non-linearities within the LMN structure.

  6. Estimation of State of Charge of a Lithium-Ion Battery Pack for Electric Vehicles Using an Adaptive Luenberger Observer

    Directory of Open Access Journals (Sweden)

    Yuan Zou

    2010-09-01

    Full Text Available In order to safely and efficiently use the power as well as to extend the lifetime of the traction battery pack, accurate estimation of State of Charge (SoC is very important and necessary. This paper presents an adaptive observer-based technique for estimating SoC of a lithium-ion battery pack used in an electric vehicle (EV. The RC equivalent circuit model in ADVISOR is applied to simulate the lithium-ion battery pack. The parameters of the battery model as a function of SoC, are identified and optimized using the numerically nonlinear least squares algorithm, based on an experimental data set. By means of the optimized model, an adaptive Luenberger observer is built to estimate online the SoC of the lithium-ion battery pack. The observer gain is adaptively adjusted using a stochastic gradient approach so as to reduce the error between the estimated battery output voltage and the filtered battery terminal voltage measurement. Validation results show that the proposed technique can accurately estimate SoC of the lithium-ion battery pack without a heavy computational load.

  7. Optimal economy-based battery degradation management dynamics for fuel-cell plug-in hybrid electric vehicles

    Science.gov (United States)

    Martel, François; Kelouwani, Sousso; Dubé, Yves; Agbossou, Kodjo

    2015-01-01

    This work analyses the economical dynamics of an optimized battery degradation management strategy intended for plug-in hybrid electric vehicles (PHEVs) with consideration given to low-cost technologies, such as lead-acid batteries. The optimal management algorithm described herein is based on discrete dynamic programming theory (DDP) and was designed for the purpose of PHEV battery degradation management; its operation relies on simulation models using data obtained experimentally on a physical PHEV platform. These tools are first used to define an optimal management strategy according to the economical weights of PHEV battery degradation and the secondary energy carriers spent to manage its deleterious effects. We then conduct a sensitivity study of the proposed optimization process to the fluctuating economic parameters associated with the fuel and energy costs involved in the degradation management process. Results demonstrate the influence of each parameter on the process's response, including daily total operating costs and expected battery lifetime, as well as establish boundaries for useful application of the method; in addition, they provide a case for the relevance of inexpensive battery technologies, such as lead-acid batteries, for economy-centric PHEV applications where battery degradation is a major concern.

  8. Advanced battery technology for electric two-wheelers in the people's Republic of China.

    Energy Technology Data Exchange (ETDEWEB)

    Patil, P. G.; Energy Systems

    2009-07-22

    This report focuses on lithium-ion (Li-ion) battery technology applications for two- and possibly three-wheeled vehicles. The author of this report visited the People's Republic of China (PRC or China) to assess the status of Li-ion battery technology there and to analyze Chinese policies, regulations, and incentives for using this technology and for using two- and three-wheeled vehicles. Another objective was to determine if the Li-ion batteries produced in China were available for benchmarking in the United States. The United States continues to lead the world in Li-ion technology research and development (R&D). Its strong R&D program is funded by the U.S. Department of Energy and other federal agencies, such as the National Institute of Standards and Technology and the U.S. Department of Defense. In Asia, too, developed countries like China, Korea, and Japan are commercializing and producing this technology. In China, more than 120 companies are involved in producing Li-ion batteries. There are more than 139 manufacturers of electric bicycles (also referred to as E-bicycles, electric bikes or E-bikes, and electric two-wheelers or ETWs in this report) and several hundred suppliers. Most E-bikes use lead acid batteries, but there is a push toward using Li-ion battery technology for two- and three-wheeled applications. Highlights and conclusions from this visit are provided in this report and summarized.

  9. A new battery capacity indicator for nickel-metal hydride battery powered electric vehicles using adaptive neuro-fuzzy inference system

    CERN Document Server

    Chau, K T; Chan, C C; Shen, W X

    2003-01-01

    This paper describes a new approach to estimate accurately the battery residual capacity (BRC) of the nickel-metal hydride (Ni-MH) battery for modern electric vehicles (EVs). The key to this approach is to model the Ni-MH battery in EVs by using the adaptive neuro-fuzzy inference system (ANFIS) with newly defined inputs and output. The inputs are the temperature and the discharged capacity distribution describing the discharge current profile, while the output is the state of available capacity (SOAC) representing the BRC. The estimated SOAC from ANFIS model and the measured SOAC from experiments are compared, and the results confirm that the proposed approach can provide an accurate estimation of the SOAC under variable discharge currents.

  10. A new battery capacity indicator for nickel-metal hydride battery powered electric vehicles using adaptive neuro-fuzzy inference system

    Energy Technology Data Exchange (ETDEWEB)

    Chau, K.T. E-mail: ktchau@eee.hku.hk; Wu, K.C.; Chan, C.C.; Shen, W.X

    2003-08-01

    This paper describes a new approach to estimate accurately the battery residual capacity (BRC) of the nickel-metal hydride (Ni-MH) battery for modern electric vehicles (EVs). The key to this approach is to model the Ni-MH battery in EVs by using the adaptive neuro-fuzzy inference system (ANFIS) with newly defined inputs and output. The inputs are the temperature and the discharged capacity distribution describing the discharge current profile, while the output is the state of available capacity (SOAC) representing the BRC. The estimated SOAC from ANFIS model and the measured SOAC from experiments are compared, and the results confirm that the proposed approach can provide an accurate estimation of the SOAC under variable discharge currents.

  11. Impact of real world driving pattern and all-electric range on battery sizing and cost of plug-in hybrid electric two-wheeler

    Science.gov (United States)

    Amjad, Shaik; Rudramoorthy, R.; Neelakrishnan, S.; Varman, K. Sri Raja; Arjunan, T. V.

    2011-03-01

    This study addresses the impact of an actual drive pattern on the sizing and cost of a battery pack for a plug-in hybrid electric two-wheeler. To estimate the daily average travel distance in fixing the all-electric range of two wheelers, a study conducted in Coimbatore city is presented. A MATLAB simulation model developed for estimating the energy and power requirements in an all-electric strategy using an Indian driving cycle (IDC) and a real-world driving pattern are discussed. The simulation results reveal the impact of the real-world driving pattern on energy consumption and also the influence of all-electric range in sizing the battery pack. To validate the results, a plug-in hybrid electric two-wheeler developed by modifying a standard two-wheeler has been tested on the road with the help of the IDC simulator kit. An annual battery cost comparison shows that nickel-metal-hydride batteries are more economical and suitable for in plug-in hybrid electric two-wheelers.

  12. Fast Charge Battery Electric Transit Bus In-Use Fleet Evaluation: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Prohaska, Robert; Eudy, Leslie; Kelly, Kenneth

    2016-05-06

    The focus of this interim fleet evaluation is to characterize and evaluate the operating behavior of Foothill Transit's fast charge battery electric buses (BEBs). Future research will compare the BEBs' performance to conventional vehicles. In an effort to better understand the impacts of drive cycle characteristics on advanced vehicle technologies, researchers at the National Renewable Energy Laboratory analyzed over 148,000 km of in-use operational data, including driving and charging events. This analysis provides an unbiased evaluation of advanced vehicle technologies in real-world operation demonstrating the importance of understanding the effects of road grade and heating, ventilating and air conditioning requirements when deploying electric vehicles. The results of this analysis show that the Proterra BE35 demonstrated an operating energy efficiency of 1.34 kWh/km over the data reporting period.

  13. Research, development, and demonstration of lead-acid batteries for electric-vehicle propulsion. Annual report, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    The first development effort in improving lead-acid batteries fore electric vehicles was the improvement of electric vehicle batteries using flat pasted positive plates and the second was for a tubular long life positive plate. The investigation of 32 component variables based on a flat pasted positive plate configuration is described. The experiment tested 96 - six volt batteries for characterization at 0, 25, and 40/sup 0/C and for cycle life capability at the 3 hour discharge rate with a one cycle, to 80% DOD, per day regime. Four positive paste formulations were selected. Two commercially available microporous separators were used in conjunction with a layer of 0.076 mm thick glass mat. Two concentrations of battery grade sulfuric acid were included in the test to determine if an increase in concentration would improve the battery capacity sufficient to offset the added weight of the more concentrated solution. Two construction variations, 23 plate elements with outside negative plates and 23 plate elements with outside positive plates, were included. The second development effort was an experiment designed to study the relationship of 32 component variables based on a tubular positive plate configuration. 96-six volt batteries were tested at various discharge rates at 0, 25, and 40/sup 0/C along with cycle life testing at 80% DOD of the 3 hour rate. 75 batteries remain on cycle life testing with 17 batteries having in excess of 365 life cycles. Preliminary conclusions indicate: the tubular positive plate is far more capable of withstanding deep cycles than is the flat pasted plate; as presently designed 40 Whr/kg can not be achieved, since 37.7 Whr/kg was the best tubular data obtained; electrolyte circulation is impaired due to the tight element fit in the container; and a redesign is required to reduce the battery weight which will improve the Whr/kg value. This redesign is complete and new molds have been ordered.

  14. Electrical, mechanical and morphological properties of compressed carbon felt electrodes in vanadium redox flow battery

    Science.gov (United States)

    Chang, Tien-Chan; Zhang, Jun-Pu; Fuh, Yiin-Kuen

    2014-01-01

    Experiments including electrical, mechanical and morphological aspects under compression in the range of 0-40% have been carried out on four potential materials for liquid diffusion layer (LDL) of vanadium redox flow battery (VRB) (including three widely used carbon felt and one recently utilized metal foam) in order to better understand the influence of the fundamental properties on the battery performance. We experimentally demonstrate that the electrical contact resistance is predominately determined by the clamping force. It is observed that increasing the stress applied on the carbon felt, which is of high interest for the durability of the membrane electrode assembly (MEA), has moreover a positive effect on their performance due to the reduced contact resistance. However, a simultaneously reduced porosity is also recorded and possibly detrimental to the mass transport of vanadium electrolyte. Moreover, the intrusion of carbon felts under compression is also characterized. Experimental results show that with the clamping force increases, both the porosity of the carbon felts underneath the rib and channel volume decrease, and this can be mainly attributed to the deformation of the carbon felts and resultant changed of the void volume as well as intrusion.

  15. Single-Phase PFC Converter for Plug-in Hybrid Electric Vehicle Battery Chargers

    Directory of Open Access Journals (Sweden)

    Shakil Ahamed Khan

    2012-06-01

    Full Text Available In this paper, a front end ac–dc power factor correction topology is proposed for plug-in hybrid electric vehicle (PHEV battery charging. The topology can achieve improved power quality, in terms of power factor correction, reduced total harmonic distortion at input ac mains, and precisely regulated dc output. Within this context, this paper introduces a boost converter topology for implementing digital power factor correction based on low cost digital signal controller that operates the converter in continuous conduction mode, thereby significantly reducing input current harmonics. The theoretical analysis of the proposed converter is then developed, while an experimental digital control system is used to implement the new control strategy. A detailed converter operation, analysis and control strategy are presented along with simulation and experimental results for universal ac input voltage (100–240V to 380V dc output at up to 3.0 kW load and a power factor greater than 0.98. Experimental results show the advantages and flexibilities of the new control method for plug-in hybrid electric vehicle (PHEV battery charging application.

  16. Research, development and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report for 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-01

    This is the first annual report describing progress in the 33-month cooperative program between Argonne National Laboratory and Gould Inc.'s Nickel-Zinc/Electric Vehicle Project. The purpose of the program is to demonstrate the technical and economic feasibility of the nickel-zinc battery for electric vehicle propulsion. The successful completion of the program will qualify the nickel-zinc battery for use in the Department of Energy's demonstration program under the auspices of Public Law 94-413.

  17. Modelling and design optimization of low speed fuel cell - battery hybrid electric vehicles. Paper no. IGEC-1-125

    International Nuclear Information System (INIS)

    A push for electric vehicles has occurred in the past several decades due to various concerns about air pollution and the contribution of emissions to global climate change. Although electric cars and buses have been the focus of much of electric vehicle development, smaller vehicles are used extensively for transportation and utility purposes in many countries. In order to explore the viability of fuel cell - battery hybrid electric vehicles, empirical fuel cell system data has been incorporated into the NREL's vehicle design and simulation tool, ADVISOR (ADvanced Vehicle SimulatOR), to predict the performance of a low-speed, fuel cell - battery electric vehicle through MATLAB Simulink. The modelling and simulation provide valuable feedback to the design optimization of the fuel cell power system. A sampling based optimization algorithm was used to explore the viability and options of a low cost design for urban use. (author)

  18. JPL's electric and hybrid vehicles project: Project activities and preliminary test results. [power conditioning and battery charge efficiency

    Science.gov (United States)

    Barber, T. A.

    1980-01-01

    Efforts to achieve a 100 mile urban range, to reduce petroleum usage 40% to 70%, and to commercialize battery technology are discussed with emphasis on an all plastic body, four passenger car that is flywheel assisted and battery powered, and on an all metal body, four passenger car with front wheel drive and front motor. For the near term case, a parallel hybrid in which the electric motor and the internal combustion engine may directly power the drive wheels, is preferred to a series design. A five passenger car in which the electric motor and the gasoline engine both feed into the same transmission is discussed. Upgraded demonstration vehicles were tested using advanced lead acid, nickel zinc, nickel iron, and zinc chloride batteries to determine maximum acceleration, constant speed, and battery behavior. The near term batteries demonstrated significant improvement relative to current lead acid batteries. The increase in range was due to improved energy density, and ampere hour capacity, with relatively 1 small weight and volume differences.

  19. Comparative costs of flexible package cells and rigid cells for lithium-ionhybrid electric vehicle batteries.

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, P. A.; Jansen, A. N.

    2006-11-28

    cells or about $24 to $74 per battery. Container experts assisted with this study, including a paid consultant and personnel at container manufacturing companies. Some of the companies are considering entering the business of manufacturing containers for hybrid vehicle battery manufacturers. For this reason they provided valuable guidance on overall approaches to reducing the costs of the cell containers. They have retained the description of some specific designs and procedures for future possible work with battery manufacturers, with whom they are now in contact. Through the guidance of these experts, we determined that a new type of container could be manufactured that would have the best features of performance and low cost of both the Rigid and Flex containers. For instance, the aluminum layer in a tri-layer sheet can be sufficiently thick to form a rigid container that can be fabricated in two halves, much like a Flex container, and mechanically joined at the edges for strength. In addition to the mechanical joint, this container can be sealed at the edges, much like a Flex container, by means of an inner polymer liner that can be heat-sealed or ultrasonically welded. The terminals can be flat strips of metal sealed into the top of the container as part of the edge sealing of the container, as for the Flex cell. Ridges can be stamped into one side of the container to provide cooling channels and the exterior layer of the container stock can be coated with a thin, electrically insulating, polymer layer. We expect this type of container will provide excellent sealing and durability and be less expensive than either the Flex or the Rigid container, which the study initially considered. A major cost for the original Rigid container is the welding required for sealing the container. However, the welding of the current collector tabs to the terminal piece may be even more complex and costly than welding the container. It is important, therefore, to develop an

  20. A Rule Based Energy Management System of Experimental Battery/Supercapacitor Hybrid Energy Storage System for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Qiao Zhang

    2016-01-01

    Full Text Available In this paper, a simple and efficient rule based energy management system for battery and supercapacitor hybrid energy storage system (HESS used in electric vehicles is presented. The objective of the proposed energy management system is to focus on exploiting the supercapacitor characteristics and on increasing the battery lifetime and system efficiency. The role of the energy management system is to yield battery reference current, which is subsequently used by the controller of the DC/DC converter. First, a current controller is designed to realize load current distribution between battery and supercapacitor. Then a voltage controller is designed to ensure the supercapacitor SOC to fluctuate within a preset reasonable variation range. Finally, a commercial experimental platform is developed to verify the proposed control strategy. In addition, the energy efficiency and the cost analysis of the hybrid system are carried out based on the experimental results to explore the most cost-effective tradeoff.

  1. [Energy Conservation and Emissions Reduction Benefits Analysis for Battery Electric Buses Based on Travel Services].

    Science.gov (United States)

    Lin, Xiao-dan; Tian, Liang; Lü, Bin; Yang, Jian-xin

    2015-09-01

    Battery Electric Bus (BEB) has become one of prior options of urban buses for its "zero emission" during the driving stage. However, the environmental performance of electric buses is affected by multi-factors from the point of whole life cycle. In practice, carrying capacity of BEB and power generation structures can both implement evident effects on the energy consumption and pollutants emission of BEB. Therefore, take the above factors into consideration, in this article, Life Cycle Assessment is employed to evaluate the energy conservation and emissions reduction benefits of BEB. Results indicate that, travel service is more reasonable as the functional unit, rather than mileage, since the carrying capacity of BEB is 15% lower than the diesel buses. Moreover, compared with diesel buses, the energy conservation and emissions reduction benefits of battery electric buses are all different due to different regional power structures. Specifically, the energy benefits are 7. 84%, 11. 91%, 26. 90%, 11. 15%, 19. 55% and 20. 31% respectively in Huabei, Huadong, Huazhong, Dongbei, Xibei and Nanfang power structure. From the point of comprehensive emissions reduction benefits, there is no benefit in Huabei power structure, as it depends heavily on coal. But in other areas, the comprehensive emissions reduction benefits of BEB are separately 3. 46%, 26. 81%, 1. 17%, 13. 74% and 17. 48% in Huadong, Huazhong, Dongbei, Xibei and Nanfang. Therefore, it suggests that, enlargement of carrying capacity should be taken as the most prior technology innovation direction for BEB, and the grids power structure should be taken into consideration when the development of BEB is in planning. PMID:26717718

  2. [Energy Conservation and Emissions Reduction Benefits Analysis for Battery Electric Buses Based on Travel Services].

    Science.gov (United States)

    Lin, Xiao-dan; Tian, Liang; Lü, Bin; Yang, Jian-xin

    2015-09-01

    Battery Electric Bus (BEB) has become one of prior options of urban buses for its "zero emission" during the driving stage. However, the environmental performance of electric buses is affected by multi-factors from the point of whole life cycle. In practice, carrying capacity of BEB and power generation structures can both implement evident effects on the energy consumption and pollutants emission of BEB. Therefore, take the above factors into consideration, in this article, Life Cycle Assessment is employed to evaluate the energy conservation and emissions reduction benefits of BEB. Results indicate that, travel service is more reasonable as the functional unit, rather than mileage, since the carrying capacity of BEB is 15% lower than the diesel buses. Moreover, compared with diesel buses, the energy conservation and emissions reduction benefits of battery electric buses are all different due to different regional power structures. Specifically, the energy benefits are 7. 84%, 11. 91%, 26. 90%, 11. 15%, 19. 55% and 20. 31% respectively in Huabei, Huadong, Huazhong, Dongbei, Xibei and Nanfang power structure. From the point of comprehensive emissions reduction benefits, there is no benefit in Huabei power structure, as it depends heavily on coal. But in other areas, the comprehensive emissions reduction benefits of BEB are separately 3. 46%, 26. 81%, 1. 17%, 13. 74% and 17. 48% in Huadong, Huazhong, Dongbei, Xibei and Nanfang. Therefore, it suggests that, enlargement of carrying capacity should be taken as the most prior technology innovation direction for BEB, and the grids power structure should be taken into consideration when the development of BEB is in planning.

  3. Evaluation of the Plug-in Hybrid Electric Vehicle Considering Learning Curve on Battery and Power Generation Best Mix

    Science.gov (United States)

    Shinoda, Yukio; Tanaka, Hideo; Akisawa, Atsushi; Kashiwagi, Takao

    Plug-in Hybrid Electric Vehicle (PHEV) is one of the technologies to reduce amount of CO2 emissions in transport section. This paper presents one of the scenarios that shows how widely used the PHEVs will be in the future. And this paper also presents how amount of CO2 will be reduced by the introduction of PHEVs, and whether there are any serious effects on power supply system in those scenarios. PHEV can run with both gasoline and electricity. Therefore we evaluate CO2 emissions not only from gasoline consumption but also from electricity consumption. To consider a distribution of daily-trip-distance is important for evaluating the economical merit and CO2 emissions by introducing of PHEV. Also, the battery cost in the future is very important for making a PHEV's growth scenario. The growth of the number of PHEV makes battery cost lower. Then, we formulate the total model that combines passenger car sector and power supply sector with considering a distribution of daily-trip-distance and Learning Curve on battery costs. We use the iteration method to consider a Learning Curve that is non- linear. Therefore we set battery cost only in the first year of the simulation. Battery costs in the later year are calculated in the model. We focus on the 25-year time frame from 2010 in Japan, with divided in 5 terms (1st∼5th). And that model selects the most economical composition of car type and power sources.

  4. Life-cycle implications and supply chain logistics of electric vehicle battery recycling in California

    International Nuclear Information System (INIS)

    Plug-in electric vehicle (PEV) use in the United States (US) has doubled in recent years and is projected to continue increasing rapidly. This is especially true in California, which makes up nearly one-third of the current US PEV market. Planning and constructing the necessary infrastructure to support this projected increase requires insight into the optimal strategies for PEV battery recycling. Utilizing life-cycle perspectives in evaluating these supply chain networks is essential in fully understanding the environmental consequences of this infrastructure expansion. This study combined life-cycle assessment and geographic information systems (GIS) to analyze the energy, greenhouse gas (GHG), water use, and criteria air pollutant implications of end-of-life infrastructure networks for lithium-ion batteries (LIBs) in California. Multiple end-of-life scenarios were assessed, including hydrometallurgical and pyrometallurgical recycling processes. Using economic and environmental criteria, GIS modeling revealed optimal locations for battery dismantling and recycling facilities for in-state and out-of-state recycling scenarios. Results show that economic return on investment is likely to diminish if more than two in-state dismantling facilities are constructed. Using rail as well as truck transportation can substantially reduce transportation-related GHG emissions (23–45%) for both in-state and out-of-state recycling scenarios. The results revealed that material recovery from pyrometallurgy can offset environmental burdens associated with LIB production, namely a 6–56% reduction in primary energy demand and 23% reduction in GHG emissions, when compared to virgin production. Incorporating human health damages from air emissions into the model indicated that Los Angeles and Kern Counties are most at risk in the infrastructure scale-up for in-state recycling due to their population density and proximity to the optimal location. (letter)

  5. Life-cycle implications and supply chain logistics of electric vehicle battery recycling in California

    Science.gov (United States)

    Hendrickson, Thomas P.; Kavvada, Olga; Shah, Nihar; Sathre, Roger; Scown, Corinne D.

    2015-01-01

    Plug-in electric vehicle (PEV) use in the United States (US) has doubled in recent years and is projected to continue increasing rapidly. This is especially true in California, which makes up nearly one-third of the current US PEV market. Planning and constructing the necessary infrastructure to support this projected increase requires insight into the optimal strategies for PEV battery recycling. Utilizing life-cycle perspectives in evaluating these supply chain networks is essential in fully understanding the environmental consequences of this infrastructure expansion. This study combined life-cycle assessment and geographic information systems (GIS) to analyze the energy, greenhouse gas (GHG), water use, and criteria air pollutant implications of end-of-life infrastructure networks for lithium-ion batteries (LIBs) in California. Multiple end-of-life scenarios were assessed, including hydrometallurgical and pyrometallurgical recycling processes. Using economic and environmental criteria, GIS modeling revealed optimal locations for battery dismantling and recycling facilities for in-state and out-of-state recycling scenarios. Results show that economic return on investment is likely to diminish if more than two in-state dismantling facilities are constructed. Using rail as well as truck transportation can substantially reduce transportation-related GHG emissions (23-45%) for both in-state and out-of-state recycling scenarios. The results revealed that material recovery from pyrometallurgy can offset environmental burdens associated with LIB production, namely a 6-56% reduction in primary energy demand and 23% reduction in GHG emissions, when compared to virgin production. Incorporating human health damages from air emissions into the model indicated that Los Angeles and Kern Counties are most at risk in the infrastructure scale-up for in-state recycling due to their population density and proximity to the optimal location.

  6. Test and evaluation of the Hoppecke Model E240G144/16 electric vehicle battery charger

    Science.gov (United States)

    Driggans, R. L.; Reese, R. W.; Keller, A. S.

    1984-11-01

    The Hoppecke Model E240 G 144/16 electric vehicle battery charger was tested. Charger input/output voltage, current, and power characteristics and input waveform distortion were measured and induced electromagnetic interference was evaluated as the charger recharged a lead acid battery pack. Electrical quantities were measured with precision volt-ampere-watt meters, frequency counters, a digital storage oscilloscope, and a spectrum analyzer. The Hoppecke charger required 12.2 hours to recharge a 144V battery from 100% depth of discharge (DOD). Energy efficiency was 82%, specific power was 81.2W/Kg (36.8W/lb), input current distortion varied from 52.6 to 73.6%, and electromagnetic interference was observed on AM radio. Charge factor was 1.25 from 100% DOD, increasing to 1.52 from 25% DOD.

  7. The effect of average cycling current on total energy of lithium-ion batteries for electric vehicles

    Science.gov (United States)

    Barai, Anup; Uddin, Kotub; Widanalage, W. D.; McGordon, Andrew; Jennings, Paul

    2016-01-01

    Predicting the remaining range of a battery reliably, accurately and simply is imperative for effective power management of electrified vehicles and reducing driver anxiety resulting from perceived low driving range. Techniques for predicting the remaining range of an electric vehicle exist; in the best cases they are scaled by factors that account for expected energy losses due to driving style, environmental conditions and the use of on-board energy consuming devices such as air-conditioning. In this work, experimental results that establish the dependence of remaining electrical energy on the vehicle battery immediate cycling history are presented. A method to estimate the remaining energy given short-term cycling history is presented. This method differs from the traditional state of charge methods typically used in battery management systems by considering energy throughput more directly.

  8. Effects of Integrating Electric Vehicles and Stationary Batteries in a Smart Urban Electricity Network

    OpenAIRE

    Kaschub, Thomas; Jochem, Patrick; Fichtner, Wolf

    2015-01-01

    The aim of the European Union to drastically reduce greenhouse gas emissions in the following decades has a great influence on the transport and the energy sector. Electric vehicles and renewable energy sources are seen as outstanding possibilities on this way. An interrelation of these technologies seems to be a promising option. In our contribution we address some challenges, which come along with this interrelation. From a system perspective, more flexibility is needed. One option is to ex...

  9. Energy Consumption of a Battery Electric Vehicle with Infinitely Variable Transmission

    Directory of Open Access Journals (Sweden)

    Francesco Bottiglione

    2014-12-01

    Full Text Available Battery electric vehicles (BEVs represent a possible sustainable solution for personal urban transportation. Presently, the most limiting characteristic of BEVs is their short range, mainly because of battery technology limitations. A proper design and control of the drivetrain, aimed at reducing the power losses and thus increasing BEV range, can contribute to make the electrification of urban transportation a convenient choice. This paper presents a simulation-based comparison of the energy efficiency performance of six drivetrain architectures for BEVs. Although many different drivetrain and transmission architectures have been proposed for BEVs, no literature was found regarding BEVs equipped with infinitely variable transmissions (IVTs. The analyzed drivetrain configurations are: single- (1G and two-speed (2G gear drives, half toroidal (HT and full toroidal (FT continuously variable transmissions (CVTs, and infinitely variable transmissions (IVTs with two different types of internal power flow (IVT-I and IVT-II. An off-line procedure for determining the most efficient control action for each drivetrain configuration is proposed, which allows selecting the optimal speed ratio for each operating condition. The energy consumption of the BEVs is simulated along the UDC (Urban Driving Cycle and Japanese 10-15 driving cycle, with a backward facing approach. In order to achieve the lowest energy consumption, a trade-off between high transmission efficiency and flexibility in terms of allowed speed ratios is required.

  10. Life cycle environmental assessment of lithium-ion and nickel metal hydride batteries for plug-in hybrid and battery electric vehicles.

    Science.gov (United States)

    Majeau-Bettez, Guillaume; Hawkins, Troy R; Strømman, Anders Hammer

    2011-05-15

    This study presents the life cycle assessment (LCA) of three batteries for plug-in hybrid and full performance battery electric vehicles. A transparent life cycle inventory (LCI) was compiled in a component-wise manner for nickel metal hydride (NiMH), nickel cobalt manganese lithium-ion (NCM), and iron phosphate lithium-ion (LFP) batteries. The battery systems were investigated with a functional unit based on energy storage, and environmental impacts were analyzed using midpoint indicators. On a per-storage basis, the NiMH technology was found to have the highest environmental impact, followed by NCM and then LFP, for all categories considered except ozone depletion potential. We found higher life cycle global warming emissions than have been previously reported. Detailed contribution and structural path analyses allowed for the identification of the different processes and value-chains most directly responsible for these emissions. This article contributes a public and detailed inventory, which can be easily be adapted to any powertrain, along with readily usable environmental performance assessments.

  11. Ford/DOE sodium-sulfur battery electric vehicle development and demonstration. Phase I-1. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-01

    The results of Phase I-A analyses and design studies are presented. The objective of the Phase I-A effort was to evaluate the sodium-sulfur battery, in an existing conventional production automobile, as a potential power source for an electric vehicle. The Phase I-A work was divided into five (5) major sub-tasks as follows: vehicle specification sub-task; NaS battery packaging study sub-task; vehicle packaging layout sub-task; electrical system study sub-task; and system study sub-tasks covering performance and economy projections, powertrain and vehicle safety issues and thermal studies. The major results of the sodium-sulfur battery powered electric vehicle study program are: the Fiesta was chosen to be the production vehicle which would be modified into a 2-passenger, electric test bed vehicle powered by a NaS battery; the vehicle mission was defined to be a 2-passenger urban/suburban commuter vehicle capable of at least 100 miles range over the CVS driving cycle and a wide open throttle capability of 0 to 50 mph in 14 seconds, or less; powertrain component specifications were defined; powertrain control strategy has been selected; and a suitable test bed vehicle package scheme has been developed.

  12. Current status of hybrid, battery and fuel cell electric vehicles: From electrochemistry to market prospects

    International Nuclear Information System (INIS)

    Decarbonising transport is proving to be one of today's major challenges for the global automotive industry due to many factors such as the increase in greenhouse gas and particulate emissions affecting not only the climate but also humans, the increase in pollution, rapid oil depletion, issues with energy security and dependency from foreign sources and population growth. For more than a century, our society has been dependent upon oil, and major breakthroughs in low- and ultra-low carbon technologies and vehicles are urgently required. This review paper highlights the current status of hybrid, battery and fuel cell electric vehicles from an electrochemical and market point of view. The review paper also discusses the advantages and disadvantages of using each technology in the automotive industry and the impact of these technologies on consumers.

  13. Techno-economic and behavioural analysis of battery electric, hydrogen fuel cell and hybrid vehicles in a future sustainable road transport system in the UK

    International Nuclear Information System (INIS)

    This paper conducts a techno-economic study on hydrogen Fuel Cell Electric Vehicles (FCV), Battery Electric Vehicles (BEV) and hydrogen Fuel Cell plug-in Hybrid Electric Vehicles (FCHEV) in the UK using cost predictions for 2030. The study includes an analysis of data on distance currently travelled by private car users daily in the UK. Results show that there may be diminishing economic returns for Plug-in Hybrid Electric Vehicles (PHEV) with battery sizes above 20 kWh, and the optimum size for a PHEV battery is between 5 and 15 kWh. Differences in behaviour as a function of vehicle size are demonstrated, which decreases the percentage of miles that can be economically driven using electricity for a larger vehicle. Decreasing carbon dioxide emissions from electricity generation by 80% favours larger optimum battery sizes as long as carbon is priced, and will reduce emissions considerably. However, the model does not take into account reductions in carbon dioxide emissions from hydrogen generation, assuming hydrogen will still be produced from steam reforming methane in 2030. - Research highlights: → Report diminishing returns for plug-in hybrids with battery sizes above 20 kWh. → The optimum size for a PHEV battery is between 5 and 15 kWh. → Current behaviour decreases percentage electric only miles for larger vehicles. → Low carbon electricity favours larger battery sizes as long as carbon is priced. → Reinforces that the FCHEV is a cheaper option than conventional ICE vehicles in 2030.

  14. Adaptive Kalman filtering based internal temperature estimation with an equivalent electrical network thermal model for hard-cased batteries

    Science.gov (United States)

    Dai, Haifeng; Zhu, Letao; Zhu, Jiangong; Wei, Xuezhe; Sun, Zechang

    2015-10-01

    The accurate monitoring of battery cell temperature is indispensible to the design of battery thermal management system. To obtain the internal temperature of a battery cell online, an adaptive temperature estimation method based on Kalman filtering and an equivalent time-variant electrical network thermal (EENT) model is proposed. The EENT model uses electrical components to simulate the battery thermodynamics, and the model parameters are obtained with a least square algorithm. With a discrete state-space description of the EENT model, a Kalman filtering (KF) based internal temperature estimator is developed. Moreover, considering the possible time-varying external heat exchange coefficient, a joint Kalman filtering (JKF) based estimator is designed to simultaneously estimate the internal temperature and the external thermal resistance. Several experiments using the hard-cased LiFePO4 cells with embedded temperature sensors have been conducted to validate the proposed method. Validation results show that, the EENT model expresses the battery thermodynamics well, the KF based temperature estimator tracks the real central temperature accurately even with a poor initialization, and the JKF based estimator can simultaneously estimate both central temperature and external thermal resistance precisely. The maximum estimation errors of the KF- and JKF-based estimators are less than 1.8 °C and 1 °C respectively.

  15. Life cycle environmental impact of high-capacity lithium ion battery with silicon nanowires anode for electric vehicles.

    Science.gov (United States)

    Li, Bingbing; Gao, Xianfeng; Li, Jianyang; Yuan, Chris

    2014-01-01

    Although silicon nanowires (SiNW) have been widely studied as an ideal material for developing high-capacity lithium ion batteries (LIBs) for electric vehicles (EVs), little is known about the environmental impacts of such a new EV battery pack during its whole life cycle. This paper reports a life cycle assessment (LCA) of a high-capacity LIB pack using SiNW prepared via metal-assisted chemical etching as anode material. The LCA study is conducted based on the average U.S. driving and electricity supply conditions. Nanowastes and nanoparticle emissions from the SiNW synthesis are also characterized and reported. The LCA results show that over 50% of most characterized impacts are generated from the battery operations, while the battery anode with SiNW material contributes to around 15% of global warming potential and 10% of human toxicity potential. Overall the life cycle impacts of this new battery pack are moderately higher than those of conventional LIBs but could be actually comparable when considering the uncertainties and scale-up potential of the technology. These results are encouraging because they not only provide a solid base for sustainable development of next generation LIBs but also confirm that appropriate nanomanufacturing technologies could be used in sustainable product development.

  16. On the aggregate grid load imposed by battery health-conscious charging of plug-in hybrid electric vehicles

    Science.gov (United States)

    Bashash, Saeid; Moura, Scott J.; Fathy, Hosam K.

    2011-10-01

    This article examines the problem of estimating the aggregate load imposed on the power grid by the battery health-conscious charging of plug-in hybrid electric vehicles (PHEVs). The article begins by generating a set of representative daily trips using (i) the National Household Travel Survey (NHTS) and (ii) a Markov chain model of both federal and naturalistic drive cycles. A multi-objective optimizer then uses each of these trips, together with PHEV powertrain and battery degradation models, to optimize both PHEV daily energy cost and battery degradation. The optimizer achieves this by varying (i) the amounts of charge obtained from the grid by each PHEV, and (ii) the timing of this charging. The article finally computes aggregate PHEV power demand by accumulating the charge patterns optimized for individual PHEV trips. The results of this aggregation process show a peak PHEV load in the early morning (between 5.00 and 6.00 a.m.), with approximately half of all PHEVs charging simultaneously. The ability to charge at work introduces smaller additional peaks in the aggregate load pattern. The article concludes by exploring the sensitivity of these results to the relative weighting of the two optimization objectives (energy cost and battery health), battery size, and electricity price.

  17. Comparison Study on Two Model-Based Adaptive Algorithms for SOC Estimation of Lithium-Ion Batteries in Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Yong Tian

    2014-12-01

    Full Text Available State of charge (SOC estimation is essential to battery management systems in electric vehicles (EVs to ensure the safe operations of batteries and providing drivers with the remaining range of the EVs. A number of estimation algorithms have been developed to get an accurate SOC value because the SOC cannot be directly measured with sensors and is closely related to various factors, such as ambient temperature, current rate and battery aging. In this paper, two model-based adaptive algorithms, including the adaptive unscented Kalman filter (AUKF and adaptive slide mode observer (ASMO are applied and compared in terms of convergence behavior, tracking accuracy, computational cost and estimation robustness against parameter uncertainties of the battery model in SOC estimation. Two typical driving cycles, including the Dynamic Stress Test (DST and New European Driving Cycle (NEDC are applied to evaluate the performance of the two algorithms. Comparison results show that the AUKF has merits in convergence ability and tracking accuracy with an accurate battery model, while the ASMO has lower computational cost and better estimation robustness against parameter uncertainties of the battery model.

  18. Estimation of State of Charge for Two Types of Lithium-Ion Batteries by Nonlinear Predictive Filter for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Yin Hua

    2015-04-01

    Full Text Available Estimation of state of charge (SOC is of great importance for lithium-ion (Li-ion batteries used in electric vehicles. This paper presents a state of charge estimation method using nonlinear predictive filter (NPF and evaluates the proposed method on the lithium-ion batteries with different chemistries. Contrary to most conventional filters which usually assume a zero mean white Gaussian process noise, the advantage of NPF is that the process noise in NPF is treated as an unknown model error and determined as a part of the solution without any prior assumption, and it can take any statistical distribution form, which improves the estimation accuracy. In consideration of the model accuracy and computational complexity, a first-order equivalent circuit model is applied to characterize the battery behavior. The experimental test is conducted on the LiCoO2 and LiFePO4 battery cells to validate the proposed method. The results show that the NPF method is able to accurately estimate the battery SOC and has good robust performance to the different initial states for both cells. Furthermore, the comparison study between NPF and well-established extended Kalman filter for battery SOC estimation indicates that the proposed NPF method has better estimation accuracy and converges faster.

  19. Research, development, and demonstration of lead-acid batteries for electric vehicle propulsion. Annual report for 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    Work performed during Oct. 1, 1979 to Sept. 30, 1980 for the development of lead-acid batteries for electric vehicle propulsion is described. During this report period many of the results frpm Globe Battery's design, materials and process development programs became evident in the achievement of the ISOA (Improved State of Art) specific energy, specific power, and energy efficiency goals while testing in progress also indicates that the cycle life goal can be met. These programs led to the establishment of a working pilot assembly line which produced the first twelve volt ISOA modules. Five of these modules were delivered to the National Battery Test Laboratory during the year for capacity, power and life testing, and assembly is in progress of three full battery systems for installation in vehicles. In the battery subsystem area, design of the acid circulation system for a ninety-six volt ISOA battery pack was completed and assembly of the first such system was initiated. Charger development has been slowed by problems encountered with reliability of some circuits but a prototype unit is being prepared which will meet the charging requirements of our ninety-six volt pack. This charger will be available during the 1981 fiscal year.

  20. Hybrid electric system based on fuel cell and battery and integrating a single dc/dc converter for a tramway

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, Luis M., E-mail: luis.fernandez@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Garcia, Pablo, E-mail: pablo.garcia@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Garcia, Carlos Andres, E-mail: carlosandres.garcia@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Jurado, Francisco, E-mail: fjurado@ujaen.e [Department of Electrical Engineering, EPS Linares, University of Jaen, C/Alfonso X, No. 28. 23700 Linares (Jaen) (Spain)

    2011-05-15

    Research highlights: {yields} Hybrid electric power system for a real surface tramway. {yields} Hybrid system based on PEM fuel cell with dc/dc converter and Ni-MH battery. {yields} New control strategy for the energy management of the tramway. {yields} Hybrid system demonstrated to meet appropriate driving cycle of the tramway. -- Abstract: This paper presents a hybrid electric power system for a real surface tramway. The hybrid system consists of two electrical energy sources integrating a single dc/dc converter to provide the power demanded by the tramway loads (four electric traction motors and auxiliary services): (1) a Polymer Electrolyte Membrane (PEM) fuel cell (FC) as the primary and (2) a rechargeable Ni-MH battery as electrical energy storage to supplement the FC over the driving cycle. According to the requirements of the real driving cycle of the tramway, it was considered a 200 kW PEM FC system with two FCs connected in parallel and a 34 Ah Ni-MH battery. The PEM FC and Ni-MH battery models were designed from commercially available components. The power conditioning system provides the appropriate power for the tramway. It is composed of: (1) a unique dc/dc boot converter which adapts the FC output voltage to the 750 V traction standard dc bus; (2) three phase inverters to drive properly each electric motors; and (3) a braking chopper to dissipate excess of regenerative braking energy. Suitable state machine control architecture is presented for the hybrid system, its objective being to provide demanded power by the driving cycle, optimizing the energy generated. Following this objective, a new state machine control strategy based on eight states decides the operating point of each component of the system and a cascade control structure allows achieving the operating points determined by the strategy. Simulation results of the real driving cycle of the tramway check the adequacy of the hybrid electric power system.

  1. A data-driven based adaptive state of charge estimator of lithium-ion polymer battery used in electric vehicles

    International Nuclear Information System (INIS)

    Highlights: • A lumped parameter battery model against different battery aging levels is proposed. • The RLS based method is used to identify the parameter of battery model in real-time. • A data-driven based adaptive SoC estimator is developed by RLS and AEKF algorithm. • The robustness of the SoC estimator against varying loading profiles is evaluated. • The robustness of the SoC estimator against different aging levels is evaluated. - Abstract: An accurate State of Charge (SoC) estimation method is one of the most significant and difficult techniques to promote the commercialization of electric vehicles. The paper attempts to make three contributions. (1) Through the recursive least square algorithm based identification method, the parameter of the lumped parameter battery model can be updated at each sampling interval with the real-time measurement of battery current and voltage, which is called the data-driven method. Note that the battery model has been improved with a simple electrochemical equation for describing the open circuit voltage against different aging levels and SoC. (2) Through the real-time updating technique of model parameter, a data-driven based adaptive SoC estimator is established with an adaptive extended Kalman filter. It has the potential to overcome the estimation error against battery degradation and varied operating environments. (3) The approach has been verified by different loading profiles of various health states of Lithium-ion polymer battery (LiPB) cells. The results indicate that the maximum estimation errors of voltage and SoC are less than 1% and 1.5% respectively

  2. U.S. Department of Energy Vehicle Technologies Program: Battery Test Manual For Plug-In Hybrid Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jon P. Christophersen

    2014-09-01

    This battery test procedure manual was prepared for the United States Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Vehicle Technologies Office. It is based on technical targets for commercial viability established for energy storage development projects aimed at meeting system level DOE goals for Plug-in Hybrid Electric Vehicles (PHEV). The specific procedures defined in this manual support the performance and life characterization of advanced battery devices under development for PHEV’s. However, it does share some methods described in the previously published battery test manual for power-assist hybrid electric vehicles. Due to the complexity of some of the procedures and supporting analysis, future revisions including some modifications and clarifications of these procedures are expected. As in previous battery and capacitor test manuals, this version of the manual defines testing methods for full-size battery systems, along with provisions for scaling these tests for modules, cells or other subscale level devices. The DOE-United States Advanced Battery Consortium (USABC), Technical Advisory Committee (TAC) supported the development of the manual. Technical Team points of contact responsible for its development and revision are Renata M. Arsenault of Ford Motor Company and Jon P. Christophersen of the Idaho National Laboratory. The development of this manual was funded by the Unites States Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Office. Technical direction from DOE was provided by David Howell, Energy Storage R&D Manager and Hybrid Electric Systems Team Leader. Comments and questions regarding the manual should be directed to Jon P. Christophersen at the Idaho National Laboratory (jon.christophersen@inl.gov).

  3. Battery-quick-replacement Operation Mode for Electric Taxi Vehicle%纯电动出租汽车快速更换电池运营模式

    Institute of Scientific and Technical Information of China (English)

    王健; 梁桂航

    2011-01-01

    提出了纯电动出租汽车快速更换电池的运营模式:每一辆纯电动出租汽车配置2组电池,电池的所有权属于独立的电池租赁公司,每次更换电池的费用按实际用电量计算,电池租赁公司实行集中充电,分散更换.指出了快速更换电池运营模式的优点,并对该运营模式进行了经济分析.该运营模式的实施,可有效促进纯电动汽车的发展.%The battery-quick-replacement operation mode for electric taxi vehicles was proposed; Each electric taxi equipped with two groups of electric battery belongs to the independent battery leasing companies. The cost of replacing battery will be calculated according to actual consumption. The battery leasing companies will charge the replaced batteries in batches and distribute the charged batteries for new replacement. The advantage of the battery-quick-replacement operation mode was explained. The economic analysis of the battery-quick-replacement operation mode was performed. The implement of this operation mode is helpful for the development of electric taxi vehicle.

  4. Test and evaluation of the chloride Spegel S1P108/30 electric vehicle battery charger

    Science.gov (United States)

    Driggans, R. L.; Keller, A. S.

    1985-09-01

    The Chloride Spegel Model S1P108/30 electric vehicle battery charger was tested by the Tennessee Valley Authority (TVA) as an account of work sponsored by the Electric Power Research Institute (EPRI). Charger input/output voltage, current, and power characteristics and input waveform distortion were measured; and induced electromagnetic interference was evaluated as the charger recharged a lead-acid battery pack. Electrical quantities were measured with precision volt-ampere-watt meters, frequency counters, a digital-storage oscilloscope, and a spectrum analyzer. THe Chloride charger required 8.5 hours to recharge a 216V tubular plate lead-acid battery from 100 percent depth of discharge (DOD). Energy efficiency was 83 percent, specific power was 37.4 W/kg (17.0 W/lb), input current distortion varied from 22.4 to 34.1 percent, and electromagnetic interference was observed on AM radio. Tests were conducted with the battery at initial DOD of 100, 75, 50, and 25 percent. Charge factor was 1.14 from 100-percent DOD, increasing to 1.39 from 25-percent DOD.

  5. Effects of the electric field on ion crossover in vanadium redox flow batteries

    International Nuclear Information System (INIS)

    Highlights: • Effects of the electric field on ion crossover and capacity decay in VRFB are studied. • The model enables the Donnan-potential jumps to be captured at electrode/membrane interfaces. • Electric field arises and affects ion crossover even at the open-circuit condition. • Enhancing electric-field-driven crossover can mitigate the capacity decay rate. - Abstract: A thorough understanding of the mechanisms of ion crossover through the membranes in vanadium redox flow batteries (VRFBs) is critically important in making improvements to the battery’s efficiency and cycling performance. In this work, we develop a 2-D VRFB model to investigate the mechanisms of ion crossover and the associated impacts it has on the battery’s performance. Unlike previously described models in the literature that simulated a single cell by dividing it into the positive electrode, membrane, and negative electrode regions, the present model incorporates all possible ion crossover mechanisms in the entire cell without a need to specify any interfacial boundary conditions at the membrane/electrode interfaces, and hence accurately captures the Donnan-potential jumps and steep gradient of species concentrations at the membrane/electrode interfaces. With our model, a particular emphasis is given to investigation of the effect of the electric field on vanadium ion crossover. One of the significant findings is that an electric field exists in the membrane even under the open-circuit condition, primarily due to the presence of the H+ concentration gradient across the membrane. This finding suggests that vanadium ions can permeate through the membrane from H+-diluted to H+-concentrated sides via migration and convection. More importantly, it is found that the rate of vanadium ion crossover and capacity decay during charge and discharge vary with the magnitude of the electric field, which is influenced by the membrane properties and operating conditions. The simulations suggest

  6. Causes for torque degradation during deceleration and the effect on the driving range of battery electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Lieb, Johannes [BMW PEUGEOT CITROEN ELECTRIFICATION, Muenchen (Germany); Wilde, Andreas [BMW Group, Muenchen (Germany); Baeker, Bernard [Dresden Univ. of Technology (Germany). Dept. of Vehicle Mechatronics

    2012-11-01

    The ability to regain considerable amounts of the kinetic energy during deceleration phases is a key aspect to increase the efficiency of battery electric vehicles (BEV). Especially in urban and highly congested areas brake energy recovery (BER) can drastically improve the vehicle's driving range. However, due to the high power peaks that go along even with moderate braking maneuvers, severe requirements are being put on the electric drivetrain. Any limitation of power in one of the components of the powertrain inevitably leads to degradation of the regenerative brake torque, thus limiting the car's energy regeneration capability. Without an integrated brake system that can compensate the torque variations during deceleration, BER may need to be decreased even further to prevent a loss of driving comfort due to dynamic changes in the vehicle's behavior. This paper deals with the causes of these torque restraints within the electric drivetrain and how they affect the energy consumption and therefore the electric driving range. A simulation environment was set up and verified based on an existing BEV to conduct parameter studies and depict the sensitivities towards environmental influences. The calculated efficiencies are based on standard drive cycles and incorporate continuous fading between regenerative braking and the use of friction brakes. Special attention was laid on the battery system since energy storage still poses a particular challenge in the development of electric vehicles. Also through the high mutual dependence of the various parameters of the battery enviromental influences become most evident. (orig.)

  7. Influence of the vehicle-to-grid strategy on the aging behavior of lithium battery electric vehicles

    International Nuclear Information System (INIS)

    Highlights: • A study of a V2G strategy considering the state of health of EVs as fundamental parameter is proposed. • A Simulation environment with 100 electric vehicle models for two different lithium-ion battery chemistries is implemented. • Real aging and electrical characteristic data are used to parameterize the battery models. • Simulation of 1 year for 4 different scenarios for two different ambient temperatures are carried out and compared. - Abstract: The main goal of this paper is to study the effect of a vehicle-to-grid (V2G) strategy on the lifetime of two different lithium-ion batteries. The work investigates how the aging effect on the electric vehicles’ (EV) battery packs due to the additional V2G use can be reduced: it is assumed that the grid is able to identify the cars within the fleet for which the ulterior aging effects caused by V2G usage are restrained in respect of the others. The chosen EVs have to contain enough energy to satisfy the grid requests in terms of power regulation. In order to analyze the possible effects on the EVs due to the mentioned strategy, a V2G simulation environment has been implemented. The system consists of 100 EVs and a grid management strategy subsystem. Each EV is represented by a battery electrical model based on electrical impedance spectroscopy (EIS) data and an aging prediction model parameterized through accelerated aging tests. In order to reproduce real scenario conditions, both the electrical battery model and the aging prediction model have been parameterized for two different cells, a LiFePO4-cathode based and an NMC-cathode based lithium-ion cell. In particular, the accelerated aging tests have been carried out for more than one year, both for calendar and cycling operation, involving around 45 cells for each of the two technologies. The grid subsystem is represented by an algorithm which is able to consider information in terms of aging and type of battery installed in the EV. This

  8. Modeling charge polarization voltage for large lithium-ion batteries in electric vehicles

    OpenAIRE

    Yan Jiang; Caiping Zhang; Weige Zhang; Wei Shi; Qiujiang Liu

    2013-01-01

    Purpose: Polarization voltage of the lithium-ion battery is an important parameter that has direct influence on battery performance. The paper aims to analyze the impedance characteristics of the lithium-ion battery based on EIS data. Design/methodology/approach: The effects of currents, initial SOC of the battery on charge polarization voltage are investigated, which is approximately linear function of charge current. The change of charge polarization voltage is also analyzed with the gradie...

  9. Energy analysis of electric vehicles using batteries or fuel cells through well-to-wheel driving cycle simulations

    Energy Technology Data Exchange (ETDEWEB)

    Campanari, Stefano; Manzolini, Giampaolo; Garcia de la Iglesia, Fernando [Politecnico di Milano, Department of Energy, Piazza Leonardo da Vinci 32, 20133 Milano (Italy)

    2009-01-15

    This work presents a study of the energy and environmental balances for electric vehicles using batteries or fuel cells, through the methodology of the well to wheel (WTW) analysis, applied to ECE-EUDC driving cycle simulations. Well to wheel balances are carried out considering different scenarios for the primary energy supply. The fuel cell electric vehicles (FCEV) are based on the polymer electrolyte membrane (PEM) technology, and it is discussed the possibility to feed the fuel cell with (i) hydrogen directly stored onboard and generated separately by water hydrolysis (using renewable energy sources) or by conversion processes using coal or natural gas as primary energy source (through gasification or reforming), (ii) hydrogen generated onboard with a fuel processor fed by natural gas, ethanol, methanol or gasoline. The battery electric vehicles (BEV) are based on Li-ion batteries charged with electricity generated by central power stations, either based on renewable energy, coal, natural gas or reflecting the average EU power generation feedstock. A further alternative is considered: the integration of a small battery to FCEV, exploiting a hybrid solution that allows recovering energy during decelerations and substantially improves the system energy efficiency. After a preliminary WTW analysis carried out under nominal operating conditions, the work discusses the simulation of the vehicles energy consumption when following standardized ECE-EUDC driving cycle. The analysis is carried out considering different hypothesis about the vehicle driving range, the maximum speed requirements and the possibility to sustain more aggressive driving cycles. The analysis shows interesting conclusions, with best results achieved by BEVs only for very limited driving range requirements, while the fuel cell solutions yield best performances for more extended driving ranges where the battery weight becomes too high. Results are finally compared to those of conventional internal

  10. Structures, phase stabilities, and electrical potentials of Li-Si battery anode materials

    KAUST Repository

    Tipton, William W.

    2013-05-28

    The Li-Si materials system holds promise for use as an anode in Li-ion battery applications. For this system, we determine the charge capacity, voltage profiles, and energy storage density solely by ab initio methods without any experimental input. We determine the energetics of the stable and metastable Li-Si phases likely to form during the charging and discharging of a battery. Ab initio molecular dynamics simulations are used to model the structure of amorphous Li-Si as a function of composition, and a genetic algorithm coupled to density-functional theory searches the Li-Si binary phase diagram for small-cell, metastable crystal structures. Calculations of the phonon densities of states using density-functional perturbation theory for selected structures determine the importance of vibrational, including zero-point, contributions to the free energies. The energetics and local structural motifs of these metastable Li-Si phases closely resemble those of the amorphous phases, making these small unit cell crystal phases good approximants of the amorphous phase for use in further studies. The charge capacity is estimated, and the electrical potential profiles and the energy density of Li-Si anodes are predicted. We find, in good agreement with experimental measurements, that the formation of amorphous Li-Si only slightly increases the anode potential. Additionally, the genetic algorithm identifies a previously unreported member of the Li-Si binary phase diagram with composition Li5Si2 which is stable at 0 K with respect to previously known phases. We discuss its relationship to the partially occupied Li7Si3 phase. © 2013 American Physical Society.

  11. Simulation-Based Approach for Studying the Balancing of Local Smart Grids with Electric Vehicle Batteries

    Directory of Open Access Journals (Sweden)

    Juhani Latvakoski

    2015-07-01

    Full Text Available Modern society is facing great challenges due to pollution and increased carbon dioxide (CO2 emissions. As part of solving these challenges, the use of renewable energy sources and electric vehicles (EVs is rapidly increasing. However, increased dynamics have triggered problems in balancing energy supply and consumption demand in the power systems. The resulting uncertainty and unpredictability of energy production, consumption, and management of peak loads has caused an increase in costs for energy market actors. Therefore, the means for studying the balancing of local smart grids with EVs is a starting point for this paper. The main contribution is a simulation-based approach which was developed to enable the study of the balancing of local distribution grids with EV batteries in a cost-efficient manner. The simulation-based approach is applied to enable the execution of a distributed system with the simulation of a local distribution grid, including a number of charging stations and EVs. A simulation system has been constructed to support the simulation-based approach. The evaluation has been carried out by executing the scenario related to balancing local distribution grids with EV batteries in a step-by-step manner. The evaluation results indicate that the simulation-based approach is able to facilitate the evaluation of smart grid– and EV-related communication protocols, control algorithms for charging, and functionalities of local distribution grids as part of a complex, critical cyber-physical system. In addition, the simulation system is able to incorporate advanced methods for monitoring, controlling, tracking, and modeling behavior. The simulation model of the local distribution grid can be executed with the smart control of charging and discharging powers of the EVs according to the load situation in the local distribution grid. The resulting simulation system can be applied to the study of balancing local smart grids with EV

  12. Real-world battery duty profile of a neighbourhood electric vehicle

    OpenAIRE

    Devie, Arnaud; VINOT, Emmanuel; Pelissier, Serge; Venet, Pascal

    2012-01-01

    The study of traction batteries real-world usage in vehicular applications faces a handful of serious challenges. To date, we are unable to accurately predict the cycle life of a battery under real-world operating conditions. There are a couple of reasons for that; on the one hand, the battery technology evolves rapidly whereas the battery cycle life testing requires large amounts of time and on the second hand, we know little about real-world duty profile of batteries. The work presented her...

  13. The revolution of batteries: electricity can be stored. Battery reaches all sectors. The Li-ion king

    International Nuclear Information System (INIS)

    Based on the lithium-ion technology, the revolution of energy storage is on the way. A first article describes how these new batteries are now introduced into the grid (for example in the USA, in the UK, in Germany, Italy, French islands, China, South Korea, Japan and Australia) and boost energy transition. With this revolution, new regulations and new business models are to be more precisely defined. Clients are asking for energy storage solutions. If new applications seem to boost it, the market remains however complex, unsteady and full of unknowns. In an interview, the Saft chairman comments the sector evolution, fields of application, the success of Tesla batteries, and the bad surprise of a sales drop for energy storage solutions for his company in 2015. The last article discusses how the Li-ion technology extends its domination, indicates the technological differences between fields of application (each application has its cathode), perspectives of improvement for the different involved chemical processes, and evokes safety issues. The article also indicates five technologies which pretend to compete with Li-ion technology (metal lithium polymer, sodium-ion, flow batteries with two electrolytes, lithium-sulphur, and lithium air)

  14. Metamodel for Efficient Estimation of Capacity-Fade Uncertainty in Li-Ion Batteries for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Jaewook Lee

    2015-06-01

    Full Text Available This paper presents an efficient method for estimating capacity-fade uncertainty in lithium-ion batteries (LIBs in order to integrate them into the battery-management system (BMS of electric vehicles, which requires simple and inexpensive computation for successful application. The study uses the pseudo-two-dimensional (P2D electrochemical model, which simulates the battery state by solving a system of coupled nonlinear partial differential equations (PDEs. The model parameters that are responsible for electrode degradation are identified and estimated, based on battery data obtained from the charge cycles. The Bayesian approach, with parameters estimated by probability distributions, is employed to account for uncertainties arising in the model and battery data. The Markov Chain Monte Carlo (MCMC technique is used to draw samples from the distributions. The complex computations that solve a PDE system for each sample are avoided by employing a polynomial-based metamodel. As a result, the computational cost is reduced from 5.5 h to a few seconds, enabling the integration of the method into the vehicle BMS. Using this approach, the conservative bound of capacity fade can be determined for the vehicle in service, which represents the safety margin reflecting the uncertainty.

  15. Role of electrical resistance of electrodes in modeling of discharging and charging of flooded lead-acid batteries

    Science.gov (United States)

    Gandhi, K. S.

    2015-03-01

    Electrical resistance of both the electrodes of a lead-acid battery increases during discharge due to formation of lead sulfate, an insulator. Work of Metzendorf [1] shows that resistance increases sharply at about 65% conversion of active materials, and battery stops discharging once this critical conversion is reached. However, these aspects are not incorporated into existing mathematical models. Present work uses the results of Metzendorf [1], and develops a model that includes the effect of variable resistance. Further, it uses a reasonable expression to account for the decrease in active area during discharge instead of the empirical equations of previous work. The model's predictions are compared with observations of Cugnet et al. [2]. The model is as successful as the non-mechanistic models existing in literature. Inclusion of variation in resistance of electrodes in the model is important if one of the electrodes is a limiting reactant. If active materials are stoichiometrically balanced, resistance of electrodes can be very large at the end of discharge but has only a minor effect on charging of batteries. The model points to the significance of electrical conductivity of electrodes in the charging of deep discharged batteries.

  16. Test and evaluation of the Philips Model PE 1701 and Lester Model 9865 electric vehicle battery chargers

    Science.gov (United States)

    Reese, R. W.; Driggans, R. L.; Keller, A. S.

    1984-04-01

    The Philips Model PE 1701 and the Lester Model 9865 electric vehicle battery chargers were tested. Charger input/output voltage, current, power characteristics, and input waveform distortion were measured and induced electromagnetic interference was evaluated while the chargers recharged a fully discharged lead-acid battery pack. Electrical quantities were measured with precision volt-ampere-watt meters, frequency counters, a digital storage oscilloscope, and a spectrum analyzer. The Philips charger required 12.2 hours to recharge a 144-V battery; it had an energy efficiency of 86.0% and a specific power of 87.4 W/kg. Input current distortion was between 6.9 and 23.0 percent, and electromagnetic interference was observed on AM radio. The Lester charger required 8.2 hours to recharge a 106-V battery; it had an energy efficiency of 83.0% and a specific power of 117.3 W/kg (53.3 W/lb). Current distortion was between 52.7 and 97.4%, and electromagnetic interference was observed on AM radio.

  17. Extended Kalman filter method for state of charge estimation of vanadium redox flow battery using thermal-dependent electrical model

    Science.gov (United States)

    Xiong, Binyu; Zhao, Jiyun; Wei, Zhongbao; Skyllas-Kazacos, Maria

    2014-09-01

    State of charge (SOC) estimation is a key issue for battery management since an accurate estimation method can ensure safe operation and prevent the over-charge/discharge of a battery. Traditionally, open circuit voltage (OCV) method is utilized to estimate the stack SOC and one open flow cell is needed in each battery stack [1,2]. In this paper, an alternative method, extended Kalman filter (EKF) method, is proposed for SOC estimation for VRBs. By measuring the stack terminal voltages and applied currents, SOC can be predicted with a state estimator instead of an additional open circuit flow cell. To implement EKF estimator, an electrical model is required for battery analysis. A thermal-dependent electrical circuit model is proposed to describe the charge/discharge characteristics of the VRB. Two scenarios are tested for the robustness of the EKF. For the lab testing scenarios, the filtered stack voltage tracks the experimental data despite the model errors. For the online operation, the simulated temperature rise is observed and the maximum SOC error is within 5.5%. It is concluded that EKF method is capable of accurately predicting SOC using stack terminal voltages and applied currents in the absence of an open flow cell for OCV measurement.

  18. Lifetime Estimation of the Nanophosphate LiFePO4/C Battery Chemistry Used in Fully Electric Vehicles

    DEFF Research Database (Denmark)

    Swierczynski, Maciej Jozef; Stroe, Daniel Loan; Stroe, Ana-Irina;

    2015-01-01

    There are currently many different lithium ion (Li-ion) chemistries available on the market, and several new players are in the research and development process; however, none of them is superior to the other chemistries in all aspects. Relatively low price, long cycle and calendar lifetime......, and intrinsic safety of the nanophosphate LiFePO4/C Li-ion chemistry make it possible to consider this chemistry for electric vehicle (EV) applications. This paper investigates the lifetime of the nanophosphate LiFePO4/C battery chemistry when it is used for full electrical vehicles. The investigation...... is performed considering a semiempirical calendar and cycle lifetime model, which was developed based on extended accelerated lifetime tests. Both capacity and power capability degradations during calendar and cycle life aging are considered and quantified. Finally, the developed battery cell lifetime model...

  19. Assessment of lithium-ion capacitor for using in battery electric vehicle and hybrid electric vehicle applications

    International Nuclear Information System (INIS)

    This paper represents a novel lithium-ion capacitor model. The proposed model has significantly high accuracy (less 4%). The model is an extension of Zubieta model for EDLCs. The proposed model consists of three capacitors, representing the influence of temperature, current rate (ΔC1) and SoC (ΔC2) on the capacitance of LiCaps, respectively. Unlike to the electrical double-layer capacitors, the model contains two resistances, illustrating the charge and discharge processes. Then, a self-discharge resistance is added to demonstrate the long term effect on the LiCaps capabilities. This model is able to predict the lithium-ion behavior during constant charging and discharging as well as during short pulses duration. The parameters of the model have been derived based on the extended characterization tests that have been carried out. The investigated performance parameters are energy and power abilities, charge and discharge capabilities at different current rates. Furthermore, these parameters have been examined at different working temperatures (60 °C, 40 °C, 25 °C, 0 °C and −18 °C). The experimental results reveal that the type of lithium-ion capacitor used in this work has an energy density about 14 Wh/kg, which is two and half times higher than the used EDLC. These results also indicate similar properties as the electrical double-layer capacitors in the terms of internal resistance and state of charge determination. In contrast to EDLCs, the results show that lithium-ion capacitors suffer considerably at the low temperatures due to lower energy at high current rate. The same characteristics can be observed during discharge phase, due to the occurrence of the Peukert effect. Moreover, series of tests have been carried out at different state of charge values. Here we have found that the capacitance has a polynomial relationship against a linear equation for EDLC and it seems in function of applied current rates. From the point of view of the power

  20. Double Resonant Topology for 72V Battery Charger used in a Hybrid Electric Locomotive - Study and Experimental Validation

    OpenAIRE

    BUTTERBACH, S; DE-BERNARDINIS, A; Lallemand, R; Coquery, G.; JEUNESSE, A; EVAIN, Y; AUBIN, PH

    2010-01-01

    This work deals with the study, adaptation and experimental validation of a 9kW lead-acid battery charger used to feed the 72VDC bus inside the hybrid electric locomotive demonstrator in the frame of the French research project PLATHEE. The topology of the charger is based on a high frequency double resonant series-parallel circuit which allows soft switching, losses minimization, reduction of passive component weight and facilitates system integration. Specific charging and floating modes we...

  1. The air quality and human health effects of integrating utility-scale batteries into the New York State electricity grid

    Science.gov (United States)

    Gilmore, Elisabeth A.; Apt, Jay; Walawalkar, Rahul; Adams, Peter J.; Lave, Lester B.

    In a restructured electricity market, utility-scale energy storage technologies such as advanced batteries can generate revenue by charging at low electricity prices and discharging at high prices. This strategy changes the magnitude and distribution of air quality emissions and the total carbon dioxide (CO 2) emissions. We evaluate the social costs associated with these changes using a case study of 500 MW sodium-sulfur battery installations with 80% round-trip efficiency. The batteries displace peaking generators in New York City and charge using off-peak generation in the New York Independent System Operator (NYISO) electricity grid during the summer. We identify and map charging and displaced plant types to generators in the NYISO. We then convert the emissions into ambient concentrations with a chemical transport model, the Particulate Matter Comprehensive Air Quality Model with extensions (PMCAM x). Finally, we transform the concentrations into their equivalent human health effects and social benefits and costs. Reductions in premature mortality from fine particulate matter (PM 2.5) result in a benefit of 4.5 ¢ kWh -1 and 17 ¢ kWh -1 from displacing a natural gas and distillate fuel oil fueled peaking plant, respectively, in New York City. Ozone (O 3) concentrations increase due to decreases in nitrogen oxide (NO x) emissions, although the magnitude of the social cost is less certain. Adding the costs from charging, displacing a distillate fuel oil plant yields a net social benefit, while displacing the natural gas plant has a net social cost. With the existing base-load capacity, the upstate population experiences an increase in adverse health effects. If wind generation is charging the battery, both the upstate charging location and New York City benefit. At 20 per tonne of CO 2, the costs from CO 2 are small compared to those from air quality. We conclude that storage could be added to existing electricity grids as part of an integrated strategy from a

  2. Development and Characterization of an Electrically Rechargeable Zinc-Air Battery Stack

    Directory of Open Access Journals (Sweden)

    Hongyun Ma

    2014-10-01

    Full Text Available An electrically rechargeable zinc-air battery stack consisting of three single cells in series was designed using a novel structured bipolar plate with air-breathing holes. Alpha-MnO2 and LaNiO3 severed as the catalysts for the oxygen reduction reaction (ORR and oxygen evolution reaction (OER. The anodic and cathodic polarization and individual cell voltages were measured at constant charge-discharge (C-D current densities indicating a uniform voltage profile for each single cell. One hundred C-D cycles were carried out for the stack. The results showed that, over the initial 10 cycles, the average C-D voltage gap was about 0.94 V and the average energy efficiency reached 89.28% with current density charging at 15 mA·cm−2 and discharging at 25 mA·cm−2. The total increase in charging voltage over the 100 C-D cycles was ~1.56% demonstrating excellent stability performance. The stack performance degradation was analyzed by galvanostatic electrochemical impedance spectroscopy. The charge transfer resistance of ORR increased from 1.57 to 2.21 Ω and that of Zn/Zn2+ reaction increased from 0.21 to 0.34 Ω after 100 C-D cycles. The quantitative analysis guided the potential for the optimization of both positive and negative electrodes to improve the cycle life of the cell stack.

  3. In-Use Fleet Evaluation of Fast-Charge Battery Electric Transit Buses

    Energy Technology Data Exchange (ETDEWEB)

    Prohaska, Robert; Kelly, Kenneth; Eudy; Leslie

    2016-06-27

    With support from the U.S. Department of Energy's Vehicle Technologies Office, the National Renewable Energy Laboratory (NREL) conducts real-world performance evaluations of advanced medium- and heavy-duty fleet vehicles. Evaluation results can help vehicle manufacturers fine-tune their designs and assist fleet managers in selecting fuel-efficient, low-emission vehicles that meet their economic and operational goals. In 2015, NREL launched an in-service evaluation of 12 battery electric buses (BEBs) compared to conventional compressed natural gas (CNG) buses operated by Foothill Transit in West Covina, California. The study aims to improve understanding of the overall usage and effectiveness of fast-charge BEBs and associated charging infrastructure in transit operation. To date, NREL researchers have analyzed more than 148,000 km of in-use operational data, including driving and charging events. Foothill Transit purchased the BEBs with grant funding from the Federal Transit Administration's Transit Investments for Greenhouse Gas and Energy Reduction Program.

  4. Application of physical electric circuit modeling to characterize Li-ion battery electrochemical processes

    Science.gov (United States)

    Greenleaf, M.; Li, H.; Zheng, J. P.

    2014-12-01

    A physical electric circuit model (PECM) was used to identify several electrochemical processes occurring in two commercial Li-ion batteries of different cathode materials (LixFePO4 and LixCoO2) via electrochemical impedance spectroscopy (EIS). Through defining these electrochemical processes in these two cells, it was determined that the charge transfer resistance (or exchange current density) observed via EIS was due to the cathodic exchange current densities in both the LixFePO4 and LixCoO2 full cells. In discussing the ionic diffusion of the examined cells, the anode of one cell and the cathode of the other were primarily responsible for the observed diffusion of the full cells. Lastly, the measured double layer capacitance was determined to be represented in EIS scans by the anodes of both full cells. The diffusion coefficient was calculated using Fick's1st Law estimation, and from this coefficient, the particle size was calculated and evaluated against scanning electron microscopy (SEM).

  5. The economic competitiveness and emissions of battery electric vehicles in China

    International Nuclear Information System (INIS)

    Highlights: • We evaluate the life-cycle cost and emissions of BEVs in China. • BEVs are not economically competitive compared with ICEVs in the Chinese market. • The value of emission reductions is small compared with the subsidy on BEVs. • The CO2 emission reduction from BEVs is relatively constant over the time. • BEVs likely will not be economically competitive in China before 2031. - Abstract: Electric vehicles (EVs) have high energy efficiency and low pollutant and greenhouse gas (GHG) emissions compared with conventional internal combustion engine vehicles (ICEVs). This study examines the economic competitiveness of battery electric vehicles (BEVs) in the Chinese market. BEVs are compared with ICEVs using benefit-cost analyses from the perspectives of consumers, society and GHG emissions. A life-cycle cost model is developed to evaluate the lifetime cost of a vehicle. The results show that, with central government subsidies, the BEV life-cycle private cost (LCPC) is about 1.4 times higher than comparable ICEVs. Central government subsidies on BEVs will not be cost effective and efficient unless the annual external cost reduction from using BEV reaches $2500 for a compact vehicle or $3600 for a multi-purpose vehicle. That total cost level would imply a carbon cost of more than $2100 per ton. The current life-cycle external cost reductions from using BEV are around $2000–$2300, which are smaller than government subsidies or LCPC differences between BEV and ICEV. Further projections show that BEVs likely will not be economically competitive in the Chinese market before 2031

  6. The ability of battery second use strategies to impact plug-in electric vehicle prices and serve utility energy storage applications

    Science.gov (United States)

    Neubauer, Jeremy; Pesaran, Ahmad

    The high cost of lithium ion batteries is a major impediment to the increased market share of plug-in hybrid electric vehicles (PHEVs) and full electric vehicles (EVs). The reuse of PHEV/EV propulsion batteries in second use applications following the end of their automotive service life may have the potential to offset the high initial cost of these batteries today. Accurately assessing the value of such a strategy is exceedingly complex and entails many uncertainties. This paper takes a first step toward such an assessment by estimating the impact of battery second use on the initial cost of PHEV/EV batteries to automotive consumers and exploring the potential for grid-based energy storage applications to serve as a market for used PHEV/EV batteries. It is found that although battery second use is not expected to significantly affect today's PHEV/EV prices, it has the potential to become a common component of future automotive battery life cycles and potentially to transform markets in need of cost-effective energy storage. Based on these findings, the authors advise further investigation focused on forecasting long-term battery degradation and analyzing second-use applications in more detail.

  7. A data-driven multi-scale extended Kalman filtering based parameter and state estimation approach of lithium-ion polymer battery in electric vehicles

    International Nuclear Information System (INIS)

    Highlights: • A data-driven multi-scale extended Kalman filtering is developed for battery system. • A lumped parameter battery model against different aging levels has been proposed. • The proposed approach has less computation efficiency but higher estimation accuracy. • The proposed approach can estimate battery parameter, capacity and SoC concurrently. • The robustness of the proposed approach against different aging levels is evaluated. - Abstract: Accurate estimations of battery parameter and state play an important role in promoting the commercialization of electric vehicles. This paper tries to make three contributions to the existing literatures through advanced time scale separation algorithm. (1) A lumped parameter battery model was improved for achieving accurate voltage estimate against different battery aging levels through an electrochemical equation, which has enhanced the relationship of battery voltage to its State-of-Charge (SoC) and capacity. (2) A multi-scale extended Kalman filtering was proposed and employed to execute the online measured data driven-based battery parameter and SoC estimation with dual time scales in regarding that the slow-varying characteristic on battery parameter and fast-varying characteristic on battery SoC, thus the battery parameter was estimated with macro scale and battery SoC was estimated with micro scale. (3) The accurate estimate of battery capacity and SoC were obtained in real-time through a data-driven multi-scale extended Kalman filtering algorithm. Experimental results on various degradation states of lithium-ion polymer battery cells further verified the feasibility of the proposed approach

  8. The experimental study of lead acid batteries for an electric hybrid drive stand

    Directory of Open Access Journals (Sweden)

    Emilian Lefter

    2008-05-01

    Full Text Available The paper aims to document a number of experimental tests conducted on some VRLA batteries. A montage scheme is proposed to monitor the behaviour of the batteries on charging and discharging. The results are presented of the measurements of the battery parameters, of the voltage in the open circuit (OCV, as well as the internal impedance, after a process of charging. Based on the catalogue data, the Peukert coefficient and the Peukert capacity are determined, which are used to determine the discharge depth of the batteries tested for the partial discharge. The schema used for discharging ispresented, and also a number of conclusions regarding the testing conditions.

  9. Demand Planning of Electric Vehicle Battery Pack Under Battery Swapping Mode%换电模式下电动汽车电池组需求规划

    Institute of Scientific and Technical Information of China (English)

    高赐威; 吴茜; 薛飞; 刘红超

    2013-01-01

      针对“集中充电、统一配送”模式下的电池数量规划问题展开研究,根据原始可用信息和规划目标要求的不同,分为远期与近期2个规划阶段,并对该问题进行建模,形成涵盖多阶段的电池数量综合规划模型。首先进行远期规划,根据电动汽车运行的相关统计参数初步估算集中型充电站最多需要购买的电池组数量,从而为近期规划提供指导。然后,近期规划基于最大日换电需求预测曲线,根据一定的物流配送原则确定日配送次数及物流能力,最终获得集中型充电站的近期规划电池组数量。算例分析表明,换电曲线的方差越小,则电池配比率越低,充裕度越高。此外,物流配送方案对电池组数量规划的影响至关重要,是影响电池组数量的关键因素。%  The electric vehicles (EV) battery pack quantity planning under the mode of centralized charging and unified distribution is researched. According to the differences between original usable information and the demand of planning objectives, the planning is divided into plannings for two stages, namely the near-term planning and the long-term planning, and corresponding models are established to form a comprehensive EV battery pack quantity planning model covering multi stages. Firstly, the long-term planning is performed, which preliminary estimates the most battery pack quantity that the centralized charging station should purchase according to relevant statistical parameters of EV operation to provide guidance for the near-term planning; secondly, based on the forecasted curve of maximum daily charging demand the near-term planning decides daily distribution times and logistics capability according to a certain logistics distribution principle;finally the EV battery pack quantity of the centralized charging station in the near-term planning is attained. Case study results show that the smaller the

  10. Dynamic electric behavior and open-circuit-voltage modeling of LiFePO{sub 4}-based lithium ion secondary batteries

    Energy Technology Data Exchange (ETDEWEB)

    Roscher, Michael A.; Sauer, Dirk Uwe [RWTH Aachen University, Electrochemical Energy Conversion and Storage Systems Group, Institute for Power, Electronics and Electrical Drives (ISEA), Jaegerstrasse 17-19, 52066 Aachen (Germany)

    2011-01-01

    Accurate battery modeling is one of the key factors in battery system design process and operation as well. Therefore, the knowledge of the distinct electric characteristics of the battery cells is mandatory. This work gives insight to the electric characteristics of lithium ion batteries (Li-ion) comprising LiFePO{sub 4}-based cathode active materials with emphasis on their specific open-circuit-voltage (OCV) characteristics including hysteresis and special OCV recovery effects, which last for several minutes or even hours after a current load is interrupted. These effects are elucidated incorporating OCV measurement data of high power cells. Simple empiric models are derived and used in a model-based state estimation algorithm. The complete battery model includes an impedance model, a hysteresis model and an OCV recovery model part. The introduced model enables the assessment of the cells' state-of-charge (SOC) precisely using model-based state estimation approaches. (author)

  11. Research, development and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report, 1979. [70 W/lb

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    This second annual report under Contract No. 31-109-39-4200 covers the period July 1, 1978 through August 31, 1979. The program demonstrates the feasibility of the nickel-zinc battery for electric vehicle propulsion. The program is divided into seven distinct but highly interactive tasks collectively aimed at the development and commercialization of nickel-zinc technology. These basic technical tasks are separator development, electrode development, product design and analysis, cell/module battery testing, process development, pilot manufacturing, and thermal management. A Quality Assurance Program has also been established. Significant progress has been made in the understanding of separator failure mechanisms, and a generic category of materials has been specified for the 300+ deep discharge (100% DOD) applications. Shape change has been reduced significantly. A methodology has been generated with the resulting hierarchy: cycle life cost, volumetric energy density, peak power at 80% DOD, gravimetric energy density, and sustained power. Generation I design full-sized 400-Ah cells have yielded in excess of 70 W/lb at 80% DOD. Extensive testing of cells, modules, and batteries is done in a minicomputer-based testing facility. The best life attained with electric vehicle-size cell components is 315 cycles at 100% DOD (1.0V cutoff voltage), while four-cell (approx. 6V) module performance has been limited to about 145 deep discharge cycles. The scale-up of processes for production of components and cells has progressed to facilitate component production rates of thousands per month. Progress in the area of thermal management has been significant, with the development of a model that accurately represents heat generation and rejection rates during battery operation. For the balance of the program, cycle life of > 500 has to be demonstrated in modules and full-sized batteries. 40 figures, 19 tables. (RWR)

  12. A highly accurate predictive-adaptive method for lithium-ion battery remaining discharge energy prediction in electric vehicle applications

    International Nuclear Information System (INIS)

    Highlights: • An energy prediction (EP) method is introduced for battery ERDE determination. • EP determines ERDE through coupled prediction of future states, parameters, and output. • The PAEP combines parameter adaptation and prediction to update model parameters. • The PAEP provides improved ERDE accuracy compared with DC and other EP methods. - Abstract: In order to estimate the remaining driving range (RDR) in electric vehicles, the remaining discharge energy (ERDE) of the applied battery system needs to be precisely predicted. Strongly affected by the load profiles, the available ERDE varies largely in real-world applications and requires specific determination. However, the commonly-used direct calculation (DC) method might result in certain energy prediction errors by relating the ERDE directly to the current state of charge (SOC). To enhance the ERDE accuracy, this paper presents a battery energy prediction (EP) method based on the predictive control theory, in which a coupled prediction of future battery state variation, battery model parameter change, and voltage response, is implemented on the ERDE prediction horizon, and the ERDE is subsequently accumulated and real-timely optimized. Three EP approaches with different model parameter updating routes are introduced, and the predictive-adaptive energy prediction (PAEP) method combining the real-time parameter identification and the future parameter prediction offers the best potential. Based on a large-format lithium-ion battery, the performance of different ERDE calculation methods is compared under various dynamic profiles. Results imply that the EP methods provide much better accuracy than the traditional DC method, and the PAEP could reduce the ERDE error by more than 90% and guarantee the relative energy prediction error under 2%, proving as a proper choice in online ERDE prediction. The correlation of SOC estimation and ERDE calculation is then discussed to illustrate the importance of an

  13. 电动汽车蓄电池的充电方法和充电设备%Charging equipment and method of electric vehicle battery

    Institute of Scientific and Technical Information of China (English)

    李俄收; 朱会田; 吴文民

    2009-01-01

    电动汽车常用的蓄电池有铅酸蓄电池、镉镍电池、氢镍电池、锂离子电池等,由于它们的结构及充电特性不同,充电时的方法也各异,这些蓄电池使用的充电设备可以是车载式、非车载式,也可以是接触式和感应式的.%Batteries of electric vehicles are commonly used lead-acid battery, Ni-Cd battery, Ni-MH battery, lithium-ion battery and so on. As a result of their construction and charging characteristics are different, methods of charging are different. Charging equipments of these batteries may take different form of vehicle-mounted, non-vehicle-mounted,contacted and the induction.

  14. A comprehensive review of on-board State-of-Available-Power prediction techniques for lithium-ion batteries in electric vehicles

    Science.gov (United States)

    Farmann, Alexander; Sauer, Dirk Uwe

    2016-10-01

    This study provides an overview of available techniques for on-board State-of-Available-Power (SoAP) prediction of lithium-ion batteries (LIBs) in electric vehicles. Different approaches dealing with the on-board estimation of battery State-of-Charge (SoC) or State-of-Health (SoH) have been extensively discussed in various researches in the past. However, the topic of SoAP prediction has not been explored comprehensively yet. The prediction of the maximum power that can be applied to the battery by discharging or charging it during acceleration, regenerative braking and gradient climbing is definitely one of the most challenging tasks of battery management systems. In large lithium-ion battery packs because of many factors, such as temperature distribution, cell-to-cell deviations regarding the actual battery impedance or capacity either in initial or aged state, the use of efficient and reliable methods for battery state estimation is required. The available battery power is limited by the safe operating area (SOA), where SOA is defined by battery temperature, current, voltage and SoC. Accurate SoAP prediction allows the energy management system to regulate the power flow of the vehicle more precisely and optimize battery performance and improve its lifetime accordingly. To this end, scientific and technical literature sources are studied and available approaches are reviewed.

  15. Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, L.H.; Joergensen, K.

    2000-04-01

    The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore to illustrate the potential synergistic interplay between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalised electricity market are analysed. The project focuses on battery electric vehicles and fuel cell vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and for the conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport vehicles. Focus is put on the Danish fleet of passenger cars and delivery vans. The scenario analysis includes assumptions on market potential developments and market penetration for the alternative vehicles. Vehicle replacement rates in the Danish transport fleet and the size of fleet development are based on data from The Danish Road Directorate. The electricity supply system development assumed is based on the Danish energy plan, Energy 21, The Plan scenario. The time horizon of the analysis is year 2030. Results from the scenario analysis include the time scales involved for the potential transition towards electricity based vehicles, the fleet composition development, the associated developments in transport fuel consumption and fuel substitution, and the potential CO{sub 2}-emission reduction achievable in the overall transport and power supply system. Detailed model simulations, on an hourly basis, have furthermore been carried out for year 2005 that address potential electricity purchase options for electric vehicles in the context of a liberalised electricity market

  16. Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

    International Nuclear Information System (INIS)

    The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore to illustrate the potential synergistic interplay between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalised electricity market are analysed. The project focuses on battery electric vehicles and fuel cell vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and for the conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport vehicles. Focus is put on the Danish fleet of passenger cars and delivery vans. The scenario analysis includes assumptions on market potential developments and market penetration for the alternative vehicles. Vehicle replacement rates in the Danish transport fleet and the size of fleet development are based on data from The Danish Road Directorate. The electricity supply system development assumed is based on the Danish energy plan, Energy 21, The Plan scenario. The time horizon of the analysis is year 2030. Results from the scenario analysis include the time scales involved for the potential transition towards electricity based vehicles, the fleet composition development, the associated developments in transport fuel consumption and fuel substitution, and the potential CO2-emission reduction achievable in the overall transport and power supply system. Detailed model simulations, on an hourly basis, have furthermore been carried out for year 2005 that address potential electricity purchase options for electric vehicles in the context of a liberalised electricity market. The

  17. Research, development and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-01

    The work carried out under the Yardney Contract with ANL for R, D and D on nickel zinc batteries over the past year was directed in three major areas: (1) elucidating the failure modes of the nickel-zinc battery system; (2) improving performance of the system; and (3) effecting a cost reduction program. Progress on the three areas is reported. (TFD)

  18. Modeling charge polarization voltage for large lithium-ion batteries in electric vehicles

    Directory of Open Access Journals (Sweden)

    Yan Jiang

    2013-06-01

    Full Text Available Purpose: Polarization voltage of the lithium-ion battery is an important parameter that has direct influence on battery performance. The paper aims to analyze the impedance characteristics of the lithium-ion battery based on EIS data. Design/methodology/approach: The effects of currents, initial SOC of the battery on charge polarization voltage are investigated, which is approximately linear function of charge current. The change of charge polarization voltage is also analyzed with the gradient analytical method in the SOC domain. The charge polarization model with two RC networks is presented, and parts of model parameters like Ohmic resistance and charge transfer impedance are estimated by both EIS method and battery constant current testing method. Findings: This paper reveals that the Ohmic resistance accounts for much contribution to battery total polarization compared to charge transfer impedance. Practical implications: Experimental results demonstrate the efficacy of the model with the proposed identification method, which provides the foundation for battery charging optimization. Originality/value: The paper analyzed the impedance characteristics of the lithium-ion battery based on EIS data, presented a charge polarization model with two RC networks, and estimated parameters like Ohmic resistance and charge transfer impedance.

  19. Thermodynamic assessment of active cooling/heating methods for lithium-ion batteries of electric vehicles in extreme conditions

    International Nuclear Information System (INIS)

    The battery cooling/heating with active methods is required for EVs (electric vehicles) in the extreme temperature conditions. This work presents a new active battery cooling/heating method based on PCS (phase change slurry) cycle. Two typical often used active cooling/heating methods so-called the direct cabin air blow and refrigerant circulation are also illustrated in detail. The thermodynamic assessment is conducted on these battery active cooling/heating methods with both of 1st Law and 2nd Law analysis. The variations of extra thermal load to the vehicle air-conditioning system are investigated as changes of ambient temperature, humidity and thermal load for the direct cabin air blow method. The simulation results show that the direct cabin air blow method causes more extra thermal load to the air-conditioning system without considering the cabin ventilation effect. The PCS cycle method performs higher exergy efficiency than that of using refrigerant circulation method. - Highlights: • An active EV battery cooling/heating method based on PCS cycle is proposed. • Thermodynamic assessments are performed for the proposed methods. • The sensitivities of operation conditions to the methods are investigated

  20. Block copolymer with simultaneous electric and ionic conduction for use in lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Javier, Anna Esmeralda K; Balsara, Nitash Pervez; Patel, Shrayesh Naran; Hallinan, Jr., Daniel T

    2013-10-08

    Redox reactions that occur at the electrodes of batteries require transport of both ions and electrons to the active centers. Reported is the synthesis of a block copolymer that exhibits simultaneous electronic and ionic conduction. A combination of Grignard metathesis polymerization and click reaction was used successively to synthesize the block copolymer containing regioregular poly(3-hexylthiophene) (P3HT) and poly(ethylene oxide) (PEO) segments. The P3HT-PEO/LiTFSI mixture was then used to make a lithium battery cathode with LiFePO.sub.4 as the only other component. All-solid lithium batteries of the cathode described above, a solid electrolyte and a lithium foil as the anode showed capacities within experimental error of the theoretical capacity of the battery. The ability of P3HT-PEO to serve all of the transport and binding functions required in a lithium battery electrode is thus demonstrated.

  1. Measurements of Electric Performance and Impedance of a 75 Ah NMC Lithium Battery Module

    DEFF Research Database (Denmark)

    Jensen, Søren Højgaard; Engelbrecht, Kurt

    2012-01-01

    Detailed characterization of battery modules is necessary to construct reliable models that incorporate performance related aspects of the modules such as thermodynamics, electrochemical reaction kinetics and degradation mechanisms. Charge-discharge curves, temperature and battery impedance...... measurements can provide information about these aspects. Charge-discharge curves can be used to measure the battery open circuit voltage and the internal resistance. Temperature measurements provide information about the thermodynamic reactions and impedance spectra yield detailed information about...... the reaction kinetics. In this paper we present the measurement methods used to examine the internal resistance, the capacity and the impedance of a 75 Ah NMC battery module. In order to measure the impedance of the battery module and of the individual cells in the module, we combine the single sine technique...

  2. Joint Estimation of the Electric Vehicle Power Battery State of Charge Based on the Least Squares Method and the Kalman Filter Algorithm

    Directory of Open Access Journals (Sweden)

    Xiangwei Guo

    2016-02-01

    Full Text Available An estimation of the power battery state of charge (SOC is related to the energy management, the battery cycle life and the use cost of electric vehicles. When a lithium-ion power battery is used in an electric vehicle, the SOC displays a very strong time-dependent nonlinearity under the influence of random factors, such as the working conditions and the environment. Hence, research on estimating the SOC of a power battery for an electric vehicle is of great theoretical significance and application value. In this paper, according to the dynamic response of the power battery terminal voltage during a discharging process, the second-order RC circuit is first used as the equivalent model of the power battery. Subsequently, on the basis of this model, the least squares method (LS with a forgetting factor and the adaptive unscented Kalman filter (AUKF algorithm are used jointly in the estimation of the power battery SOC. Simulation experiments show that the joint estimation algorithm proposed in this paper has higher precision and convergence of the initial value error than a single AUKF algorithm.

  3. Technology Status and Expected Greenhouse Gas Emissions of Battery, Plug-In Hybrid, and Fuel Cell Electric Vehicles

    Science.gov (United States)

    Lipman, Timothy E.

    2011-11-01

    Electric vehicles (EVs) of various types are experiencing a commercial renaissance but of uncertain ultimate success. Many new electric-drive models are being introduced by different automakers with significant technical improvements from earlier models, particularly with regard to further refinement of drivetrain systems and important improvements in battery and fuel cell systems. The various types of hybrid and all-electric vehicles can offer significant greenhouse gas (GHG) reductions when compared to conventional vehicles on a full fuel-cycle basis. In fact, most EVs used under most condition are expected to significantly reduce lifecycle GHG emissions. This paper reviews the current technology status of EVs and compares various estimates of their potential to reduce GHGs on a fuel cycle basis. In general, various studies show that battery powered EVs reduce GHGs by a widely disparate amount depending on the type of powerplant used and the particular region involved, among other factors. Reductions typical of the United States would be on the order of 20-50%, depending on the relative level of coal versus natural gas and renewables in the powerplant feedstock mix. However, much deeper reductions of over 90% are possible for battery EVs running on renewable or nuclear power sources. Plug-in hybrid vehicles running on gasoline can reduce emissions by 20-60%, and fuel cell EV reduce GHGs by 30-50% when running on natural gas-derived hydrogen and up to 95% or more when the hydrogen is made (and potentially compressed) using renewable feedstocks. These are all in comparison to what is usually assumed to be a more advanced gasoline vehicle "baseline" of comparison, with some incremental improvements by 2020 or 2030. Thus, the emissions from all of these EV types are highly variable depending on the details of how the electric fuel or hydrogen is produced.

  4. Off-grid hybrid electric power supply system, using a combination of solar cells, small scale wind turbine and batteries

    Energy Technology Data Exchange (ETDEWEB)

    Schroeter, W.

    1994-03-01

    The design of an off-grid electric power supply system consisting of a small scale wind turbine, a combination of solar cells and batteries is described. The robust, small scale FC 4000 wind turbine, which needs little maintenance, can be used under varying climatic conditions. It is equipped with a permanent-magnet generator with an output of 1.5 kW. The generator`s rotor is directly coupled with the wind turbine`s rotor and is without a gearbox, so the frequency and output varies according to wind speed. The 12 m{sup 2} solar cell system consists of round modules embedded in glass and with an efficiency of 13%. The lead acid batteries are used when power consumption exceeds production and store energy for future use. Further adjustments are necessary in order to optimize the performance of this hybrid system. (AB)

  5. An Inexpensive Aqueous Flow Battery for Large-Scale Electrical Energy Storage Based on Water-Soluble Organic Redox Couples

    Energy Technology Data Exchange (ETDEWEB)

    Yang, B; Hoober-Burkhardt, L; Wang, F; Prakash, GKS; Narayanan, SR

    2014-05-21

    We introduce a novel Organic Redox Flow Battery (ORBAT), for Meeting the demanding requirements of cost, eco-friendliness, and durability for large-scale energy storage. ORBAT employs two different water-soluble organic redox couples on the positive and negative side of a flow battery. Redox couples such as quinones are particularly attractive for this application. No precious metal catalyst is needed because of the fast proton-coupled electron transfer processes. Furthermore, in acid media, the quinones exhibit good chemical stability. These properties render quinone-based redox couples very attractive for high-efficiency metal-free rechargeable batteries. We demonstrate the rechargeability of ORBAT with anthraquinone-2-sulfonic acid or anthraquinone-2,6-disulfonic acid on the negative side, and 1,2-dihydrobenzoquinone- 3,5-disulfonic acid on the positive side. The ORBAT cell uses a membrane-electrode assembly configuration similar to that used in polymer electrolyte fuel cells. Such a battery can be charged and discharged multiple times at high faradaic efficiency without any noticeable degradation of performance. We show that solubility and mass transport properties of the reactants and products are paramount to achieving high current densities and high efficiency. The ORBAT configuration presents a unique opportunity for developing an inexpensive and sustainable metal-free rechargeable battery for large-scale electrical energy storage. (C) The Author(s) 2014. Published by ECS. This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 License (CC BY, http://creativecommons.orgilicenses/by/4.0/), which permits unrestricted reuse of the work in any medium, provided the original work is properly cited. All rights reserved.

  6. Electric batteries. Fundamental principles and theory, present state of the art of technology and trends of development. 3. rev. and enlarged ed. Batterien. Grundlagen und Theorie, aktueller technischer Stand und Entwicklungstendenzen

    Energy Technology Data Exchange (ETDEWEB)

    Kiehne, H.A.; Berndt, D.; Boettger, K.; Fischer, W.; Franke, H.; Friedheim, G.; Koethe, H.K.; Krakowski, H.; Middendorf, E.; Preuss, P.

    1988-01-01

    This volume gives a comprehensive survey of the present state of the electrochemical power storage with special consideration of their technical characteristics of application. The volume is structured as follows: 1) Electrochemical energy storage, general fundamentals; 2) Batteries for electric-powered industrial trucks; 2a) Energy supply concepts for driverless industrial trucks; 3) Batteries for electric-powered road vehicles; 4) Battery-fed electric drive from the user's point of view (=charging, maintenance); 5) Secured power supply with electric batteries; 6) Batteries for stationary power supplies; 7) Operation and use of batteries for a large-scale consumer (emergency power supplies for communication equipment of the Deutsche Bundespost); 8) Starter batteries of vehicles; 9) High-energy batteries (e.g. Zn/Cl/sub 2/-, Na/S-, Li/FeS-cells, fuel cells); 10) Solar-electric power supply with batteries; 11) Charging methods and charging technique; 12) Technology of battery chargers and current transformer, monitoring methods; 13) Standards and regulations for batteries and battery systems. (MM) With 192 figs.

  7. High thermal performance lithium-ion battery pack including hybrid active–passive thermal management system for using in hybrid/electric vehicles

    International Nuclear Information System (INIS)

    In this study, a novel Li-ion battery pack design including hybrid active–passive thermal management system is presented. The battery pack is suitable for using in hybrid/electric vehicles. Active part of the hybrid thermal management system uses distributed thin ducts, air flow and natural convection as cooling media while the passive part utilizes phase change material/expanded graphite composite (PCM/EG) as cooling/heating component to optimize the thermal performance of the proposed battery pack. High melting enthalpy of PCM/EG composite together with melting of PCM/EG composite at the temperature of 58.9 °C remains the temperature distribution of the battery units in the desired temperature range (below 60 °C). The temperature and voltage distributions in the proposed battery pack design consisting of battery units, distributed thin ducts and PCM/EG composite are calculated by numerical solving of the related partial differential equations. Simulation results obtained by writing M-files code in Matlab environment and plotting the numerical data are presented to validate the theoretical results. A comparison between the thermal and physical characteristics of the proposed battery pack and other latest works is presented that explicitly proves the battery pack performance. - Highlights: • Novel Li-ion battery pack including active and passive thermal management systems. • The battery pack has high thermal performance for ambient temperatures until 55 °C. • Uniform temperature and voltage distributions. • The maximum observed temperature in each battery unit is less than other works. • The maximum temperature dispersion in each battery is less than other works

  8. Research, development and demonstration of lead-acid batteries for electric vehicle propulsion. Annual report, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    This report describes work performed from October 1, 1978 to September 30, 1979. The approach for development of both the Improved State-of-the-Art (ISOA) and Advanced lead-acid batteries is three pronged. This approach concentrates on simultaneous optimization of battery design, materials, and manufacturing processing. The 1979 fiscal year saw the achievement of significant progress in the program. Some of the major accomplishments of the year are outlined. 33 figures, 13 tables. (RWR)

  9. Electric Car

    Science.gov (United States)

    1977-01-01

    NASA's Lewis Research Center undertook research toward a practical, economical battery with higher energy density. Borrowing from space satellite battery technology, Lewis came up with a nickel-zinc battery that promises longer life and twice the range of the lead-acid counterpart. Lewis researchers fabricated a prototype battery and installed it in an Otis P-500 electric utility van, using only the battery space already available and allowing battery weight equal to that of the va's conventional lead-acid battery

  10. Lead-acid battery with improved cycle life and increased efficiency for lead leveling application and electric road vehicles

    Science.gov (United States)

    Winsel, A.; Schulz, J.; Guetlich, K. F.

    1983-11-01

    Lifetime and efficiency of lead acid batteries are discussed. A gas lift pump was used to prevent acid stratification and to reduce the charging factor (down to 1.03 to 1.05). A re-expansion method was applied and an expander depot and a compound separation were built in. Cycle life is increased from 700 cycles to 1690 cycles. Efficiency is increased by energy and time saving due to the reduced charging factor and by the use of a recombination stopper and a charge indicator with remote control. It is suggested that the lead acid system is still one of the best possibilities for electric road vehicle applications.

  11. Research, development, and demonstration of nickel-iron batteries for electric vehicle propulsion. Annual report, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    The program has progressed to the stage of evaluating full-sized (220 Ah) cells, multicell modules, and 22 kWh batteries. Nickel electrodes that display stable capacities of up to 24 Ah/plate (at C/3 drain rate) at design thickness (2.5 mm) in tests at 200/sup +/ test cycles. Iron electrodes of the composite-type are also delivering 24 Ah/plate (at C/3) at target thickness (1.0 mm). Iron plates are displaying capacity stability for 300/sup +/ test cycles in continuing 3 plate cell tests. Best finished cells are delivering 57 to 63 Wh/kg at C/3, based on cell weights of the finished cells, and in the actual designed cell volume. 6-cell module (6-1) performance has demonstrated 239 Ah, 1735 Wh, 53 WH/kg at the C/3 drain rate. This module is now being evaluated at the National Battery Test Laboratory. The 2 x 4 battery has been constructed, tested, and delivered for engineering test and evaluation. The battery delivered 22.5 kWh, as required (199 Ah discharge at 113 V-bar) at the C/3 drain rate. The battery has performed satisfactorily under dynamometer and constant current drain tests. Some cell problems, related to construction, necessitated changing 3 modules, but the battery is now ready for further testing. Reduction in nickel plate swelling (and concurrent stack electrolyte starvation), to improve cycling, is one area of major effort to reach the final battery objectives. Pasted nickel electrodes are showing promise in initial full-size cell tests and will continue to be evaluated in finished cells, along with other technology advancements. 30 figures, 14 tables.

  12. 换电模式下电动汽车电池移动板的研制与应用%Development and Application of the Battery Moving Plate on Electric Vehicles Under Battery Swapping Modes

    Institute of Scientific and Technical Information of China (English)

    钟恒坚; 戴咏夏

    2015-01-01

    动力电池置换是电动汽车日常换电工作的一项重要程序。针对电动汽车后备箱内电池移动缺乏辅助工具、后备箱饰件极易摩擦破损等问题,分析了后备箱辅助移动板的主体板材及减少摩擦力部件材料,研制了新型的蜂窝式电池移动板。实际应用表明,应用该电池移动板可使换电工作更为轻松省力,提高了安全性和工作效率,减少了车辆后备箱检修维护成本。%Battery replacement is an important program for daily swapping of electric vehicles. For it lacks ap-purtenance to move batteries in boots of electric vehicles and ornaments of the boots can easily be damaged, this paper analyzes the main board and component materials reducing friction force of auxiliary moving plates in the boots. A new type of cellular battery moving plate is developed. Practical application shows that the battery moving plate enables easier battery replacement, improves safety and work efficiency and reduces boot overhaul and maintenance cost of electric vehicles.

  13. Design and cost study for development of lead--acid batteries suitable for electric vehicle propulsion. Final report. [Goals of 60 Wh/kg and 1000 cycles

    Energy Technology Data Exchange (ETDEWEB)

    Weinlein, C E

    1977-01-01

    A design for an improved state-of-the-art (ISOA) battery is proposed in this report. It is believed that this ISOA design is the most efficient design achievable within the constraints of the ISOA battery development program. These constraints include realistic time and financial limitations, and compatibility with existing high-speed production equipment. The ISOA battery is in fact an improved, state-of-the-art lead--acid battery suitable for use in an electric vehicle. A durable, light-weight polypropylene container and cover complete with single-point watering and venting features are incorporated in the ISOA design. A number of materials and process parameters with profound affect on battery performance will be chosen only after extensive evaluation and cell testing. Development of an advanced lead--acid electric vehicle battery will involve the evaluation and application of effective forward concepts in the design of the battery. Many weight-saving designs will be incorporated. Significant improvements in active material efficiencies and integrity are required. The goals of 60 Wh/kg and 1000 life cycles are ambitious but achievable. The cycle life goal appears to be the most formidable. Investigations of charging equipment and parameters will be undertaken. The impact of manufacturing plants on the environment and natural resources is discussed. 3 figures, 23 tables. (RWR)

  14. A Novel Lithium Ion Battery Autonomous Strategy Improvement Based on SVM-DTC for Urban Electric Vehicle under Several Speeds Tests

    Directory of Open Access Journals (Sweden)

    Nasri Abdelfatah

    2011-12-01

    Full Text Available One of the main challenges in the modern commercialized electric vehicle (EV is the battery management system. In this paper a novel strategy of EV power management is presented based on direct torque space vector modulation. We used the battery state of charge (SOC which is the percent of residual capacity by nominal capacity. The proper estimation of SOC of Lithium-ion battery provides an energy management system in EV. The proposed controller provides a good torque control and speed stability improvement.

  15. High-performance combination method of electric network frequency and phase for audio forgery detection in battery-powered devices.

    Science.gov (United States)

    Savari, Maryam; Abdul Wahab, Ainuddin Wahid; Anuar, Nor Badrul

    2016-09-01

    Audio forgery is any act of tampering, illegal copy and fake quality in the audio in a criminal way. In the last decade, there has been increasing attention to the audio forgery detection due to a significant increase in the number of forge in different type of audio. There are a number of methods for forgery detection, which electric network frequency (ENF) is one of the powerful methods in this area for forgery detection in terms of accuracy. In spite of suitable accuracy of ENF in a majority of plug-in powered devices, the weak accuracy of ENF in audio forgery detection for battery-powered devices, especially in laptop and mobile phone, can be consider as one of the main obstacles of the ENF. To solve the ENF problem in terms of accuracy in battery-powered devices, a combination method of ENF and phase feature is proposed. From experiment conducted, ENF alone give 50% and 60% accuracy for forgery detection in mobile phone and laptop respectively, while the proposed method shows 88% and 92% accuracy respectively, for forgery detection in battery-powered devices. The results lead to higher accuracy for forgery detection with the combination of ENF and phase feature. PMID:27442454

  16. An Adaptive Gain Nonlinear Observer for State of Charge Estimation of Lithium-Ion Batteries in Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Yong Tian

    2014-09-01

    Full Text Available The state of charge (SOC is important for the safety and reliability of battery operation since it indicates the remaining capacity of a battery. However, it is difficult to get an accurate value of SOC, because the SOC cannot be directly measured by a sensor. In this paper, an adaptive gain nonlinear observer (AGNO for SOC estimation of lithium-ion batteries (LIBs in electric vehicles (EVs is proposed. The second-order resistor–capacitor (2RC equivalent circuit model is used to simulate the dynamic behaviors of a LIB, based on which the state equations are derived to design the AGNO for SOC estimation. The model parameters are identified using the exponential-function fitting method. The sixth-order polynomial function is used to describe the highly nonlinear relationship between the open circuit voltage (OCV and the SOC. The convergence of the proposed AGNO is proved using the Lyapunov stability theory. Two typical driving cycles, including the New European Driving Cycle (NEDC and Federal Urban Driving Schedule (FUDS are adopted to evaluate the performance of the AGNO by comparing with the unscented Kalman filter (UKF algorithm. The experimental results show that the AGNO has better performance than the UKF algorithm in terms of reducing the computation cost, improving the estimation accuracy and enhancing the convergence ability.

  17. A New Method to Plan the Capacity and Location of Battery Swapping Station for Electric Vehicle Considering Demand Side Management

    Directory of Open Access Journals (Sweden)

    Wenxia Liu

    2016-06-01

    Full Text Available Compared to electric vehicle (EV charging mode, battery swapping mode can realize concentrated and orderly charging. Therefore battery swapping stations (BSS can participate in the demand side management (DSM as an integrated form. In this context, a new method to plan the capacity and location of BSS for EV, considering DSM, is proposed in this paper. Firstly, based on the original charging power of BSS with the rule of “First-In First-Out”, a bi-level optimal configuration model of BSS, in which net profit of BSS is maximized in the upper model and operating cost of Distribution Company is minimized in the lower model, is developed to decide the rated power, number of batteries, contract pricing and dispatched power of BSS for DSM. Then, the optimal locating model of BSS with the objective of minimizing network loss is built. A mesh adaptive direct search algorithm with YALMIP toolbox is applied to optimize the bi-level model. Simulation calculation was carried on IEEE-33 nodes distribution system and the results show that participating in DSM can improve the economic benefits of both BSS and distribution network and promote the consumption of distributed generation, verifying the feasibility and effectiveness of the proposed method.

  18. A new comparison between the life cycle greenhouse gas emissions of battery electric vehicles and internal combustion vehicles

    International Nuclear Information System (INIS)

    Electric vehicles have recently been gaining increasing worldwide interest as a promising potential long-term solution to sustainable personal mobility; in particular, battery electric vehicles (BEVs) offer zero tailpipe emissions. However, their true ability to contribute to greenhouse gas (GHG) emissions reductions can only be properly assessed by comparing a life cycle assessment of their GHG emissions with a similar assessment for conventional internal combustion vehicles (ICVs). This paper presents an analysis for vehicles typically expected to be introduced in 2015 in two example markets (the UK and California), taking into account the impact of three important factors: •Like-for-like vehicle comparison and effect of real-world driving conditions. •Accounting for the GHG emissions associated with meeting the additional electricity demand for charging the batteries. •GHG emissions associated with vehicle manufacture, disposal, etc. This work demonstrates that all of these factors are important and emphasises that it is therefore crucial to clearly define the context when presenting conclusions about the relative GHG performance of BEVs and ICVs – such relative performance depends on a wide range of factors, including the marginal regional grid GHG intensity, vehicle size, driving pattern, loading, etc. - Highlights: ► Develops new insights into the life cycle GHG emissions of electric vehicles. ► Addresses like-for-like vehicle comparison and effect of real-world driving. ► Accounts for marginal GHG intensity of the electricity used to charge EVs. ► Accounts for the GHG emissions associated with vehicle manufacture and disposal.

  19. Battery systems engineering

    CERN Document Server

    Rahn, Christopher D

    2012-01-01

    A complete all-in-one reference on the important interdisciplinary topic of Battery Systems Engineering Focusing on the interdisciplinary area of battery systems engineering, this book provides the background, models, solution techniques, and systems theory that are necessary for the development of advanced battery management systems. It covers the topic from the perspective of basic electrochemistry as well as systems engineering topics and provides a basis for battery modeling for system engineering of electric and hybrid electric vehicle platforms. This original

  20. A Real-Time Joint Estimator for Model Parameters and State of Charge of Lithium-Ion Batteries in Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Jianping Gao

    2015-08-01

    Full Text Available Accurate state of charge (SoC estimation of batteries plays an important role in promoting the commercialization of electric vehicles. The main work to be done in accurately determining battery SoC can be summarized in three parts. (1 In view of the model-based SoC estimation flow diagram, the n-order resistance-capacitance (RC battery model is proposed and expected to accurately simulate the battery’s major time-variable, nonlinear characteristics. Then, the mathematical equations for model parameter identification and SoC estimation of this model are constructed. (2 The Akaike information criterion is used to determine an optimal tradeoff between battery model complexity and prediction precision for the n-order RC battery model. Results from a comparative analysis show that the first-order RC battery model is thought to be the best based on the Akaike information criterion (AIC values. (3 The real-time joint estimator for the model parameter and SoC is constructed, and the application based on two battery types indicates that the proposed SoC estimator is a closed-loop identification system where the model parameter identification and SoC estimation are corrected mutually, adaptively and simultaneously according to the observer values. The maximum SoC estimation error is less than 1% for both battery types, even against the inaccurate initial SoC.

  1. Thermal analysis of large-capacity LiFePO4 power batteries for electric vehicles

    Science.gov (United States)

    Lin, Chunjing; Xu, Sichuan; Li, Zhao; Li, Bin; Chang, Guofeng; Liu, Jinling

    2015-10-01

    Excellent design of a thermal management system requires good understanding of the thermal behaviors of power batteries. In this study, the electrochemical and heat performances of a prismatic 40 Ah C/LiFePO4 battery are investigated with a focus on the influence of temperature on cell capacity in a mixed charge-discharge cycle. In addition, the heat generation and energy efficiency of a battery are determined during charge and discharge at different current rates. The experimental results indicate that in certain temperature ranges, both the charging and discharging capacities increase significantly as the temperature increases. In addition, the energy efficiency reaches more than 95% when the battery runs at a current rate of 0.33 C-2 C and temperature of 25-45 °C. A thermal mathematical model based on experimentally obtained internal resistances and entropy coefficients is developed. Using this model, the increase in the battery temperature is simulated based on specific heat values that are measured experimentally and calculated theoretically. The results from the simulation indicate that the temperature increase agrees well with the experimental values, the measured specific heat provides better results than the calculated specific heat and the heat generated decreases as the temperature increases.

  2. Battery System and Energy Storage Application of Electric Vehicle%电动汽车的电池系统及储能应用

    Institute of Scientific and Technical Information of China (English)

    廖强强; 王博; 赵书奇; 孙波; 周国定; 刘怡; 孙峻

    2015-01-01

    电动汽车电池系统的容量在0~100 kWh,与小型的分布式储能系统容量相当。在满足电动汽车行驶里程的情况下,适时地将电动汽车电池通过V2G或V2H模式应用于电力储能,可实现电动汽车电池的多功能用途,提升其附加价值。电动汽车电池退役以后,虽然容量衰减至80%以下,但大部分仍然有储能应用价值。通过评估、分级、成组等工序,将退役电动汽车电池制作成分布式储能系统,从而延长电动汽车电池的循环寿命。与电力储能相结合,充分做好电动汽车电池的梯次利用,既可以降低电动汽车电池的成本,又可以降低电力储能的成本。%Electric vehicle’s battery system capacity is from 0 to 100 kWh, which is equal to small distributed energy storage system capacity. Under the condition of meeting electric vehicle mileage, people apply seemly electric vehicle battery to power storage through V2G or V2H mode to realize electric vehicle multi-functional and improve its added value. After electric vehicle is retired, though battery capacity is below 80%, most of them are worth energy storage. Through evaluation, classification and grouping process, retired electric vehicle battery could transfer into distributed energy storage system to extend life cycle of electric vehicle battery. Combined with electric power storage, people should make full use of electric vehicle battery echelon use, which could reduce both electric vehicle battery cost and electric power storage cost.

  3. High-performance batteries for stationary energy storage and electric-vehicle propulsion. Progress report, April--June 1977

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-10-01

    Research, development, and management activities of the program on lithium--aluminum/metal sulfide batteries during April--June 1977 are described. These batteries are being developed for electric-vehicle propulsion and stationary energy storage. The present cells, which operate at 400--450/sup 0/C, are of a vertically oriented, prismatic design with a central positive electrode of FeS or FeS/sub 2/, two facing negative electrodes of lithium--aluminum alloy, and an electrolyte of molten LiCl--KCl. Testing and evaluation of industrially fabricated cells is continuing. Li--Al/FeS and Li--Al/FeS/sub 2/ cells from Eagle--Picher Industries and from Gould Inc. were tested. These tests provided information on the effects of design modifications and alternative materials for cells. Improved electrode and cell designs are being developed and tested, and the more promising designs are incorporated into the industrially fabricated cells. Among the concepts receiving major attention are carbon-bonded positive electrodes, scaled-up designs of stationary energy storage cells, additives to extend electrode lifetime, alternative electrode separators, and pellet-grid electrodes. Materials development efforts included the development of a lightweight electrical feedthrough; studies of various current-collector designs; investigation of powder separators; wettability and corrosion tests of materials for cell components; and postoperative examinations of cells. Cell chemistry studies were concerned with discharge mechanisms of FeS electrodes and with other transition-metal sulfides as positive electrode materials. Voltammetric studies were conducted to investigate the reversibility of the FeS/sub 2/ electrode. The use of calcium and magnesium alloys for the negative electrode in advanced battery systems were investigated. 8 figures, 12 tables.

  4. Modeling the performance and cost of lithium-ion batteries for electric-drive vehicles.

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, P. A.

    2011-10-20

    This report details the Battery Performance and Cost model (BatPaC) developed at Argonne National Laboratory for lithium-ion battery packs used in automotive transportation. The model designs the battery for a specified power, energy, and type of vehicle battery. The cost of the designed battery is then calculated by accounting for every step in the lithium-ion battery manufacturing process. The assumed annual production level directly affects each process step. The total cost to the original equipment manufacturer calculated by the model includes the materials, manufacturing, and warranty costs for a battery produced in the year 2020 (in 2010 US$). At the time this report is written, this calculation is the only publically available model that performs a bottom-up lithium-ion battery design and cost calculation. Both the model and the report have been publically peer-reviewed by battery experts assembled by the U.S. Environmental Protection Agency. This report and accompanying model include changes made in response to the comments received during the peer-review. The purpose of the report is to document the equations and assumptions from which the model has been created. A user of the model will be able to recreate the calculations and perhaps more importantly, understand the driving forces for the results. Instructions for use and an illustration of model results are also presented. Almost every variable in the calculation may be changed by the user to represent a system different from the default values pre-entered into the program. The distinct advantage of using a bottom-up cost and design model is that the entire power-to-energy space may be traversed to examine the correlation between performance and cost. The BatPaC model accounts for the physical limitations of the electrochemical processes within the battery. Thus, unrealistic designs are penalized in energy density and cost, unlike cost models based on linear extrapolations. Additionally, the

  5. Micro-hybrid electric vehicle application of valve-regulated lead-acid batteries in absorbent glass mat technology: Testing a partial-state-of-charge operation strategy

    Science.gov (United States)

    Schaeck, S.; Stoermer, A. O.; Hockgeiger, E.

    The BMW Group has launched two micro-hybrid functions in high volume models in order to contribute to reduction of fuel consumption in modern passenger cars. Both the brake energy regeneration (BER) and the auto-start-stop function (ASSF) are based on the conventional 14 V vehicle electrical system and current series components with only little modifications. An intelligent control algorithm of the alternator enables recuperative charging in braking and coasting phases, known as BER. By switching off the internal combustion engine at a vehicle standstill the idling fuel consumption is effectively reduced by ASSF. By reason of economy and package a lead-acid battery is used as electrochemical energy storage device. The BMW Group assembles valve-regulated lead-acid (VRLA) batteries in absorbent glass mat (AGM) technology in the micro-hybrid electrical power system since special challenges arise for the batteries. By field data analysis a lower average state-of-charge (SOC) due to partial state-of-charge (PSOC) operation and a higher cycling rate due to BER and ASSF are confirmed in this article. Similar to a design of experiment (DOE) like method we present a long-term lab investigation. Two types of 90 Ah VRLA AGM batteries are operated with a test bench profile that simulates the micro-hybrid vehicle electrical system under varying conditions. The main attention of this lab testing is focused on capacity loss and charge acceptance over cycle life. These effects are put into context with periodically refresh charging the batteries in order to prevent accelerated battery aging due to hard sulfation. We demonstrate the positive effect of refresh chargings concerning preservation of battery charge acceptance. Furthermore, we observe moderate capacity loss over 90 full cycles both at 25 °C and at 3 °C battery temperature.

  6. Towards a Friendly Energy Management Strategy for Hybrid Electric Vehicles with Respect to Pollution, Battery and Drivability

    Directory of Open Access Journals (Sweden)

    Guillaume Colin

    2014-09-01

    Full Text Available The paper proposes a generic methodology to incorporate constraints (pollutant emission, battery health, drivability into on-line energy management strategies (EMSs for hybrid electric vehicles (HEVs and plug-in hybrid electric vehicles (PHEVs. The integration of each constraint into the EMS, made with the Pontryagin maximum principle, shows a tradeoff between the fuel consumption and the constraint introduced. As state dynamics come into play (catalyst temperature, battery cell temperature, etc., the optimization problem becomes more complex. Simulation results are presented to highlight the contribution of this generic strategy, including constraints compared to the standard approach. These results show that it is possible to find an energy management strategy that takes into account an increasing number of constraints (drivability, pollution, aging, environment, etc.. However, taking these constraints into account increases fuel consumption (the existence of a trade-off curve. This trade-off can be sometimes difficult to find, and the tools developed in this paper should help to find an acceptable solution quickly

  7. Giant Electric-Field-Induced Strain in PVDF-Based Battery Separator Membranes Probed by Electrochemical Strain Microscopy.

    Science.gov (United States)

    Romanyuk, Konstantin; Costa, Carlos M; Luchkin, Sergey Yu; Kholkin, Andrei L; Lanceros-Méndez, Senentxu

    2016-05-31

    Efficiency of lithium-ion batteries largely relies on the performance of battery separator membrane as it controls the mobility and concentration of Li-ions between the anode and cathode electrodes. Recent advances in electrochemical strain microscopy (ESM) prompted the study of Li diffusion and transport at the nanoscale via electromechanical strain developed under an application of inhomogeneous electric field applied via the sharp ESM tip. In this work, we observed unexpectedly high electromechanical strain developed in polymer membranes based on porous poly(vinylidene fluoride) (PVDF) and poly(vinylidene fluoride-co-chlorotrifluoroethylene) (PVDF-CTFE) and, using it, could study a dynamics of electroosmotic flow of electrolyte inside the pores. We show that, independently of the separator membrane, electric field-induced deformation observed by ESM on wetted membrane surfaces can reach up to 10 nm under a moderate bias of 1 V (i.e., more than an order of magnitude higher than that in best piezoceramics). Such a high strain is explained by the electroosmotic flow in a porous media composed of PVDF. It is shown that the strain-based ESM method can be used to extract valuable information such as average pore size, porosity, elasticity of membrane in electrolyte solvent, and membrane-electrolyte affinity expressed in terms of zeta potential. Besides, such systems can, in principle, serve as actuators even in the absence of apparent piezoelectricity in amorphous PVDF. PMID:27142946

  8. Study of tin-sulphur-carbon nanocomposites based on electrically exploded tin as anode for sodium battery

    Science.gov (United States)

    Pervez, S. A.; Kim, D.; Lee, S.-M.; Doh, C.-H.; Lee, S.; Farooq, U.; Saleem, M.

    2016-05-01

    An electrochemical study of tin-sulphur-carbon nano-composites, based on electrically exploded tin-carbon nanoparticles as anode for sodium-ion battery (NIB), is carried out in electrolytes with and without fluoroethylene carbonate (FEC). The composites are synthesized through high energy mechanical milling (HEMM) of electrical exploded tin, sulphur nanoparticles and grinded carbon. The final product consists of tin sulfide nanoparticles embedded in amorphous carbon matrix. The results demonstrate an excellent response for the electrode materials in terms of initial discharge capacity (>425 mAhg-1) and cyclic performance (415 mAhg-1 after 50 cycles). Even more remarkably, at high current densities of 400, 600, and 800 mAg-1, electrodes still offer specific capacities of about 375, 355, and 315 mAhg-1, respectively, suggesting good rate capability of the materials. Furthermore, it is observed that the material response is much better when electrolyte has FEC as an additive which helped in the formation of an optimized SEI layer. Such an improved electrochemical performance of the electrode materials highlights their suitability for the recently emerging Na-ion battery technology.

  9. Design and simulation of a fast-charging station for plug-in hybrid electric vehicle (PHEV) batteries

    Science.gov (United States)

    de Leon, Nathalie Pulmones

    2011-12-01

    With the increasing interest in green technologies in transportation, plug-in hybrid electric vehicles (PHEV) have proven to be the best short-term solution to minimize greenhouse gas emissions. Despite such interest, conventional vehicle drivers are still reluctant in using such a new technology, mainly because of the long duration (4-8 hours) required to charge PHEV batteries with the currently existing Level I and II chargers. For this reason, Level III fast-charging stations capable of reducing the charging duration to 10-15 minutes are being considered. The present thesis focuses on the design of a fast-charging station that uses, in addition to the electrical grid, two stationary energy storage devices: a flywheel energy storage and a supercapacitor. The power electronic converters used for the interface of the energy sources with the charging station are designed. The design also focuses on the energy management that will minimize the PHEV battery charging duration as well as the duration required to recharge the energy storage devices. For this reason, an algorithm that minimizes durations along with its mathematical formulation is proposed, and its application in fast charging environment will be illustrated by means of two scenarios.

  10. Electrical Vehicle Batteries Testing in a Distribution Network Using Sustainable Energy

    DEFF Research Database (Denmark)

    Forero Camacho, Oscar Mauricio; Nørgård, Per Bromand; Rao, Ningling;

    2014-01-01

    EV technologies are still relatively new and under strong development. Many different designs and choices of technologies have been pursued by the automotive OEMs, battery industry and EV research centers. Although some standardized solutions are being promoted and becoming a new trend, there is ...... in terms of regulation of the aggregated local power, power capacity and the power exchange with the grid....

  11. Design and Control of a Multiple Input DC/DC Converter for Battery/Ultra-capacitor Based Electric Vehicle Power System

    DEFF Research Database (Denmark)

    Schaltz, Erik; Li, Zhihao; Onar, Omer;

    2009-01-01

    Battery/Ultra-capacitor based electrical vehicles (EV) combine two energy sources with different voltage levels and current characteristics. This paper focuses on design and control of a multiple input DC/DC converter, to regulate output voltage from different inputs. The proposed multi-input con......Battery/Ultra-capacitor based electrical vehicles (EV) combine two energy sources with different voltage levels and current characteristics. This paper focuses on design and control of a multiple input DC/DC converter, to regulate output voltage from different inputs. The proposed multi...

  12. Development status of zinc air power battery for electric vehicles%汽车用锌空气动力电池研究现状

    Institute of Scientific and Technical Information of China (English)

    景义军; 郭际; 孟宪玲; 武彩霞

    2011-01-01

    锌空气电池具有高比能量、低成本、无污染、不燃爆、可循环利用等优势,适宜用作城市电动汽车的动力电源.目前国内外电动汽车用锌空气动力电池主要采用机械充电式锌空气电池和锌膏循环式锌空气电池两种结构,这两种结构都是通过更换锌负极使电池连续工作.论述了锌空气动力电池还需要解决一些问题,并分析了其发展前景.%Zinc air battery can be an alternative power source for urban electric vehicles due to its high specific energy, low cost, non-pollution, non-explosion and recycle. Now, zinc air battery structures for electric vehicles mainly include mechanically rechargeable zinc air battery and zinc air battery with zinc slurry cycle system. The batteries with both structures continuously work by replacing the discharged zinc electrode with the new zinc electrode or the zinc slurry. The problems of zinc air power battery needed to be solved further were discussed, and its development prospect was analyzed.

  13. Battery switch for downhole tools

    Science.gov (United States)

    Boling, Brian E.

    2010-02-23

    An electrical circuit for a downhole tool may include a battery, a load electrically connected to the battery, and at least one switch electrically connected in series with the battery and to the load. The at least one switch may be configured to close when a tool temperature exceeds a selected temperature.

  14. Cost-effectiveness of plug-in hybrid electric vehicle battery capacity and charging infrastructure investment for reducing US gasoline consumption

    International Nuclear Information System (INIS)

    Federal electric vehicle (EV) policies in the United States currently include vehicle purchase subsidies linked to EV battery capacity and subsidies for installing charging stations. We assess the cost-effectiveness of increased battery capacity vs. nondomestic charging infrastructure installation for plug-in hybrid electric vehicles as alternate methods to reduce gasoline consumption for cars, trucks, and SUVs in the US. We find across a wide range of scenarios that the least-cost solution is for more drivers to switch to low-capacity plug-in hybrid electric vehicles (short electric range with gasoline backup for long trips) or gasoline-powered hybrid electric vehicles. If more gasoline savings are needed per vehicle, nondomestic charging infrastructure installation is substantially more expensive than increased battery capacity per gallon saved, and both approaches have higher costs than US oil premium estimates. Cost effectiveness of all subsidies are lower under a binding fuel economy standard. Comparison of results to the structure of current federal subsidies shows that policy is not aligned with fuel savings potential, and we discuss issues and alternatives. - Highlights: ► We compare cost of PHEV batteries vs. charging infrastructure per gallon of gasoline saved. ► The lowest cost solution is to switch more drivers to low-capacity PHEVs and HEVs. ► If more gasoline savings is needed, batteries offer a better value than chargers. ► Extra batteries and chargers are both more costly per gal than oil premium estimates. ► Current subsidies are misaligned with fuel savings. We discuss alternatives.

  15. THE CAUSES AND PREVENTION MEASURES OF PREMATURE AGING FOR ELECTRIC VEHICLE BATTERY%电动车电瓶早衰原因及其预防措施

    Institute of Scientific and Technical Information of China (English)

    赵正平; 张媛

    2012-01-01

    针对现有电动车电瓶早衰严重的问题,结合电瓶的工作原理,深入分析了电瓶早衰的原因,并提出了具体的预防措施。试验表明,这些措施能够较好地保证电瓶的使用寿命,预防早衰,具有很好的应用参考价值。%According to the premature aging of battery for electric vehicle, combining the battery works, the paper deeply analyses the causes of premature aging of battery and puts forward the specific preventive measures. Experiment shows that these measures can ensure the service life of the battery and have a good value for application.

  16. Composit, Nanoparticle-Based Anode material for Li-ion Batteries Applied in Hybrid Electric (HEV's)

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Malgorzata Gulbinska

    2009-08-24

    Lithium-ion batteries are promising energy storage devices in hybrid and electric vehicles with high specific energy values ({approx}150 Wh/kg), energy density ({approx}400 Wh/L), and long cycle life (>15 years). However, applications in hybrid and electric vehicles require increased energy density and improved low-temperature (<-10 C) performance. Silicon-based anodes are inexpensive, environmentally benign, and offer excellent theoretical capacity values ({approx}4000 mAh/g), leading to significantly less anode material and thus increasing the overall energy density value for the complete battery (>500 Wh/L). However, tremendous volume changes occur during cycling of pure silicon-based anodes. The expansion and contraction of these silicon particles causes them to fracture and lose electrical contact to the current collector ultimately severely limiting their cycle life. In Phase I of this project Yardney Technical Products, Inc. proposed development of a carbon/nano-silicon composite anode material with improved energy density and silicon's cycleability. In the carbon/nano-Si composite, silicon nanoparticles were embedded in a partially-graphitized carbonaceous matrix. The cycle life of anode material would be extended by decreasing the average particle size of active material (silicon) and by encapsulation of silicon nanoparticles in a ductile carbonaceous matrix. Decreasing the average particle size to a nano-region would also shorten Li-ion diffusion path and thus improve rate capability of the silicon-based anodes. Improved chemical inertness towards PC-based, low-temperature electrolytes was expected as an additional benefit of a thin, partially graphitized coating around the active electrode material.

  17. State of charge estimation of Li-ion batteries in an electric vehicle based on a radial-basis-function neural network

    Institute of Scientific and Technical Information of China (English)

    Bi Jun; Shao Sai; Guan Wei; Wang Lu

    2012-01-01

    The on-line estimation of the state of charge (SOC) of the batteries is important for the reliable running of the pure electric vehicle in practice.Because a nonlinear feature exists in the batteries and the radial-basis-function neural network (RBF NN) has good characteristics to solve the nonlinear problem,a practical method for the SOC estimation of batteries based on the RBF NN with a small number of input variables and a simplified structure is proposed.Firstly,in this paper,the model of on-line SOC estimation with the RBF NN is set.Secondly,four important factors for estimating the SOC are confirmed based on the contribution analysis method,which simplifies the input variables of the RBF NN and enhances the real-time performance of estimation.Finally,the pure electric buses with LiFePO4Li-ion batteries running during the period of the 2010 Shanghai World Expo are considered as the experimental object.The performance of the SOC estimation is validated and evaluated by the battery data from the electric vehicle.

  18. An adaptive Kalman filtering based State of Charge combined estimator for electric vehicle battery pack

    International Nuclear Information System (INIS)

    Ah counting is not a satisfactory method for the estimation of the State of Charge (SOC) of a battery, as the initial SOC and coulombic efficiency are difficult to measure. To address this issue, a new SOC estimation method, denoted as 'AEKFAh', is proposed. This method uses the adaptive Kalman filtering method which can avoid filtering divergence resulting from uncertainty to correct for the initial value used in the Ah counting method. A Ni/MH battery test procedure, consisting of 8.08 continuous Federal Urban Driving Schedule (FUDS) cycles, is carried out to verify the method. The SOC estimation error is 2.4% when compared with the real SOC obtained from a discharge test. This compares favorably with an estimation error of 11.4% when using Ah counting.

  19. Electric and hybrid vehicles charge efficiency tests of ESB EV-106 lead acid batteries

    Science.gov (United States)

    Rowlette, J. J.

    1981-01-01

    Charge efficiencies were determined by measurements made under widely differing conditions of temperature, charge procedure, and battery age. The measurements were used to optimize charge procedures and to evaluate the concept of a modified, coulometric state of charge indicator. Charge efficiency determinations were made by measuring gassing rates and oxygen fractions. A novel, positive displacement gas flow meter which proved to be both simple and highly accurate is described and illustrated.

  20. High-performance batteries for electric-vehicle propulsion and stationary energy storage. Progress report, October 1978-March 1979. [Ca/sulfides

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-05-01

    This report covers the research, development, and management activities of the programs at Argonne National Laboratory (ANL) and at subcontractors' laboratories on high-temperature batteries during the period October 1978 to March 1979. These batteries are being developed for electric-vehicle propulsion and for stationary energy-storage applications. The present cells, which operate at 400 to 500/sup 0/C, are of a vertically oriented, prismatic design with one or more inner positive electrodes of FeS or FeS/sub 2/, facing electrodes of lithium-aluminum alloy, and molten LiCl-KCl electrolyte. During this six-month period, cell and battery development work continued at ANL, Eagle-Picher Industries, Inc., Gould Inc., and the Energy Systems Group of Rockwell International. Fabrication of a 40-kWh battery by Eagle-Picher for testing in an electric van is nearing completion. Cost and design studies for a Mark II electric-vehicle battery, which will have somewhat higher performance and use potentially low-cost materials and fabrication methods, were conducted by all three subcontractors, and contracts are being negotiated for development of Mark II batteries. Conceptual design studies continued at Rockwell International on a 100 MWh stationary energy-storage module. The present plan is to construct a module based on these designs for testing at the BEST (Battery Energy Storage Test) Facility. Work was also in progress at the Carborundum Co., General Motors Research Laboratories, and various other organizations on developing materials and components for cells. 38 figures, 28 tables.

  1. Direct electrical stimulation using a battery-operated device for induction and modulation of colonic contractions in pigs.

    Science.gov (United States)

    Bertschi, Mattia; Schlageter, Vincent; Vesin, Jean-Marc; Aellen, Steve; Peloponissios, Nicolas; D'Ambrogio, Aris; Wiesel, Paul Herman; Givel, Jean-Claude; Kucera, Pavel; Virag, Nathalie

    2010-07-01

    Direct electrical stimulation of the colon offers a promising approach for the induction of propulsive colonic contractions by using an implantable device. The objective of this study was to assess the feasibility to induce colonic contractions using a commercially available battery-operated stimulator (maximum pulse width of 1 ms and maximum amplitude of 10 V). Three pairs of pacing electrodes were inserted into the cecal seromuscular layer of anesthetized pigs. During a first set of in vivo experiments conducted on six animals, a pacing protocol leading to cecum contractions was determined: stimulation bursts with 1 ms pulse width, 10 V amplitude (7-15 mA), 120 Hz frequency, and 30-s burst duration, repeated every 2-5 min. In a second testing phase, an evaluation of the pacing protocol was performed in four animals (120 stimulation bursts in total). By using the battery-operated stimulator, contractions of the cecum and movement of contents could be induced in 92% of all stimulations. A cecal shortening of about 30% and an average intraluminal pressure increase of 10.0 +/- 6.0 mmHg were observed. PMID:20300849

  2. Adaptive approach for on-board impedance parameters and voltage estimation of lithium-ion batteries in electric vehicles

    Science.gov (United States)

    Farmann, Alexander; Waag, Wladislaw; Sauer, Dirk Uwe

    2015-12-01

    Robust algorithms using reduced order equivalent circuit model (ECM) for an accurate and reliable estimation of battery states in various applications become more popular. In this study, a novel adaptive, self-learning heuristic algorithm for on-board impedance parameters and voltage estimation of lithium-ion batteries (LIBs) in electric vehicles is introduced. The presented approach is verified using LIBs with different composition of chemistries (NMC/C, NMC/LTO, LFP/C) at different aging states. An impedance-based reduced order ECM incorporating ohmic resistance and a combination of a constant phase element and a resistance (so-called ZARC-element) is employed. Existing algorithms in vehicles are much more limited in the complexity of the ECMs. The algorithm is validated using seven day real vehicle data with high temperature variation including very low temperatures (from -20 °C to +30 °C) at different Depth-of-Discharges (DoDs). Two possibilities to approximate both ZARC-elements with finite number of RC-elements on-board are shown and the results of the voltage estimation are compared. Moreover, the current dependence of the charge-transfer resistance is considered by employing Butler-Volmer equation. Achieved results indicate that both models yield almost the same grade of accuracy.

  3. Plug-in Hybrid and Battery-Electric Vehicles: State of the research and development and comparative analysis of energy and cost efficiency

    OpenAIRE

    Francoise Nemry; Guillaume Leduc; Almudena Muñoz

    2009-01-01

    This technical note is a first contribution from IPTS to a JRC more integrated assessment of future penetration pathways of new vehicles technologies in the EU27 market and of their impacts on energy security, GHG emissions and on the economy. The present report focuses on battery electric vehicles (BEVs) and plug-in hybrid electric vehicles (PHEVs). It provides a general overview of the current state of the research and development about the concerned technologies and builds some first estim...

  4. Comparison of Ultra capacitors and Batteries Technologies to Optimize Hybrid Electric Vehicle Efficiency

    OpenAIRE

    Nzisabira, Jonathan; Louvigny, Yannick; Duysinx, Pierre

    2008-01-01

    The acceptance of Electric and Hybrid Electric Vehicle is related to their eco-efficiency, i.e. their ability to both reduce environmental impact while also providing a sufficient user satisfaction. The objective of this study is to provide a rationale design tool based on a multidisciplinary optimization approach to support the design of hybrid electric powertrain to simultaneously maximize user satisfaction complex criteria and minimize the Eco-score. In order to carry out the optimization ...

  5. Effect of hybrid system battery performance on determining CO2 emissions of hybrid electric vehicles in real-world conditions

    International Nuclear Information System (INIS)

    Hybrid electric vehicles (HEVs) can potentially reduce vehicle CO2 emissions by using recuperated kinetic vehicle energy stored as electric energy in a hybrid system battery (HSB). HSB performance affects the individual net HEV CO2 emissions for a given driving pattern, which is considered to be equivalent to unchanged net energy content in the HSB. The present study investigates the influence of HSB performance on the statutory correction procedure used to determine HEV CO2 emissions in Europe based on chassis dynamometer measurements with three identical in-use examples of a full HEV model featuring different mileages. Statutory and real-world driving cycles and full electric vehicle operation modes have been considered. The main observation is that the selected HEVs can only use 67-80% of the charge provided to the HSB, which distorts the outcomes of the statutory correction procedure that does not consider such irreversibility. CO2 emissions corrected according to this procedure underestimate the true net CO2 emissions of one HEV by approximately 13% in real-world urban driving. The correct CO2 emissions are only reproduced when considering the HSB performance in this driving pattern. The statutory procedure for correcting HEV CO2 emissions should, therefore, be adapted.

  6. Electrical, Mechanical, and Capacity Percolation Leads to High-Performance MoS2/Nanotube Composite Lithium Ion Battery Electrodes.

    Science.gov (United States)

    Liu, Yuping; He, Xiaoyun; Hanlon, Damien; Harvey, Andrew; Khan, Umar; Li, Yanguang; Coleman, Jonathan N

    2016-06-28

    Advances in lithium ion batteries would facilitate technological developments in areas from electrical vehicles to mobile communications. While two-dimensional systems like MoS2 are promising electrode materials due to their potentially high capacity, their poor rate capability and low cycle stability are severe handicaps. Here, we study the electrical, mechanical, and lithium storage properties of solution-processed MoS2/carbon nanotube anodes. Nanotube addition gives up to 10(10)-fold and 40-fold increases in electrical conductivity and mechanical toughness, respectively. The increased conductivity results in up to a 100× capacity enhancement to ∼1200 mAh/g (∼3000 mAh/cm(3)) at 0.1 A/g, while the improved toughness significantly boosts cycle stability. Composites with 20 wt % nanotubes combine high reversible capacity with excellent cycling stability (e.g., ∼950 mAh/g after 500 cycles at 2 A/g) and high rate capability (∼600 mAh/g at 20 A/g). The conductivity, toughness, and capacity scale with nanotube content according to percolation theory, while the stability increases sharply at the mechanical percolation threshold. We believe that the improvements in conductivity and toughness obtained after addition of nanotubes can be transferred to other electrode materials, such as silicon nanoparticles. PMID:27203558

  7. Mesoporous Block Copolymer Battery Separators

    OpenAIRE

    Wong, David Tunmin

    2012-01-01

    In the past two decades, lithium-ion batteries have emerged as an increasingly important technology. They are used almost ubiquitously in laptops and cell phones because of their relatively high energy densities when compared to other battery chemistries. More recently, lithium-ion batteries have been employed in the automotive sector in both pure electric vehicles and hybrid electric vehicles. However, one of the major barriers in the widespread adoption of lithium-ion batteries in electric ...

  8. Battery Test Manual For 12 Volt Start/Stop Hybrid Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Belt, Jeffrey R. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-05-01

    This manual was prepared by and for the United Stated Advanced Battery Consortium (USABC) Electrochemical Energy Storage Team. It is based on the targets established for 12 Volt Start/Stop energy storage development and is similar (with some important changes) to an earlier manual for the former FreedomCAR program. The specific procedures were developed primarily to characterize the performance of energy storage devices relative to the USABC requirements. However, it is anticipated that these procedures will have some utility for characterizing 12 Volt Start/Stop hybrid energy storage device behavior in general.

  9. Dead Battery? Wind Power, the Spot Market, and Hydro Power Interaction in the Nordic Electricity Market

    OpenAIRE

    Mauritzen, Johannes

    2012-01-01

    It is well established within both the economics and power system engineering literature that hydro power can act as a complement to large amounts of intermittent energy. In particular hydro power can act as a "battery" where large amounts of wind power are installed. In this paper I use simple distributed lag models with data from Denmark and Norway. I find that increased wind power in Denmark causes increased marginal exports to Norway and that this effect is larger during periods of net ex...

  10. Impacts of battery characteristics, driver preferences and road network features on travel costs of a plug-in hybrid electric vehicle (PHEV) for long-distance trips

    International Nuclear Information System (INIS)

    In a road network with refueling and fast charging stations, the minimum-cost driving path of a plug-in hybrid electric vehicle (PHEV) depends on factors such as location and availability of refueling/fast charging stations, capacity and cost of PHEV batteries, and driver tolerance towards extra mileage or additional stopping. In this paper, our focus is long-distance trips of PHEVs. We analyze the impacts of battery characteristics, often-overlooked driver preferences and road network features on PHEV travel costs for long-distance trips and compare the results with hybrid electric and conventional vehicles. We investigate the significance of these factors and derive critical managerial insights for shaping the future investment decisions about PHEVs and their infrastructure. In particular, our findings suggest that with a certain level of deployment of fast charging stations, well established cost and emission benefits of PHEVs for the short range trips can be extended to long distance. Drivers' stopping intolerance may hamper these benefits; however, increasing battery capacity may help overcome the adverse effects of this intolerance. - Highlights: • We investigate the travel costs of CVs, HEVs and PHEVs for long-distance trips. • We analyze the impacts of battery, driver and road network characteristics on the costs. • We provide critical managerial insights to shape the investment decisions about PHEVs. • Drivers' stopping intolerance may hamper the cost and emission benefits of PHEVs. • Negative effect of intolerance on cost may be overcome by battery capacity expansion

  11. Online Estimation of Peak Power Capability of Li-Ion Batteries in Electric Vehicles by a Hardware-in-Loop Approach

    Directory of Open Access Journals (Sweden)

    Fengchun Sun

    2012-05-01

    Full Text Available Battery peak power capability estimations play an important theoretical role for the proper use of the battery in electric vehicles. To address the failures in relaxation effects and real-time ability performance, neglecting the battery’s design limits and other issues of the traditional peak power capability calculation methods, a new approach based on the dynamic electrochemical-polarization (EP battery model, taking into consideration constraints of current, voltage, state of charge (SoC and power is proposed. A hardware-in-the-loop (HIL system is built for validating the online model-based peak power capability estimation approach of batteries used in hybrid electric vehicles (HEVs and a HIL test based on the Federal Urban Driving Schedules (FUDS is used to verify and evaluate its real-time computation performance, reliability and robustness. The results show the proposed approach gives a more accurate estimate compared with the hybrid pulse power characterization (HPPC method, avoiding over-charging or over-discharging and providing a powerful guarantee for the optimization of HEVs power systems. Furthermore, the HIL test provides valuable data and critical guidance to evaluate the accuracy of the developed battery algorithms.

  12. A data-driven adaptive state of charge and power capability joint estimator of lithium-ion polymer battery used in electric vehicles

    International Nuclear Information System (INIS)

    An accurate SoC (state of charge) and SoP (state of power capability) joint estimator is the most significant techniques for electric vehicles. This paper makes two contributions to the existing literature. (1) A data-driven parameter identification method has been proposed for accurately capturing the real-time characteristic of the battery through the recursive least square algorithm, where the parameter of the battery model is updated with the real-time measurements of battery current and voltage at each sampling interval. (2) An adaptive extended Kalman filter algorithm based multi-state joint estimator has been developed in accordance with the relationship of the battery SoC and its power capability. Note that the SoC and SoP can be predicted accurately against the degradation and various operating environments of the battery through the data-driven parameter identification method. The robustness of the proposed data-driven joint estimator has been verified by different degradation states of lithium-ion polymer battery cells. The result indicates that the estimation errors of voltage and SoC are less than 1% even if given a large erroneous initial state of joint estimator, which makes the SoP estimate more accurate and reliable for the electric vehicles application. - Highlights: • A data-driven parameter identification method is developed by RLS algorithm. • An adaptive multi-state joint estimator of the battery is developed by AEKF algorithm. • A data-driven SoC and SoP joint estimator is developed with the real-time measurement. • Robustness of the joint estimator is verified by different aging states of LiPB cells

  13. 电动汽车锂电池SOC估计研究%Study on SOC Estimation of Lithium Battery in Electric Car

    Institute of Scientific and Technical Information of China (English)

    郑媛; 李宽; 刘希闻

    2015-01-01

    针对电动汽车锂电池的荷电状态不能被直接测量的现状,以容量为12 Ah的高功率锂电池为研究对象,为该对象建立了等效电路模型,并对电池的模型参数进行辨识,辨识的电池模型参数能够较好地模拟电池的动静态特性。最后对所建立的模型设计状态观测器来估算电池的S O C,仿真结果及分析表明,所设计的控制策略能够较好的估算电池的荷电状态,为算法在实车上进行测试提供了理论依据。%For SOC of Lithium battery in electric car can not be directly measured, the capacity of 12 Ah high power lithium battery was as the research object in the paper, the equivalent circuit model of the battery is established, and the parameters of battery model were identified, the parameters of battery model can be well simulated the dynamic and static characteristics of the battery. Finally, the proposed model state observer is designed to estimate the SOC of the battery, the simulation results and analysis show that the designed control strategy can be better estimated the battery charged state, which provides a theoretical basis that the algorithm is tested on the real car.

  14. Research On Electric Vehicle Battery Thermal Management System%电动汽车动力电池组热管理系统研究

    Institute of Scientific and Technical Information of China (English)

    杨国胜

    2015-01-01

    相比较传统燃油汽车,电动汽车具有更加高效、更加清洁的优点。电动汽车工作性能的好坏很大程度上取决于电池的工作性能。温度作为影响电池工作性能的重要因素,对电动汽车的使用性和安全性有着非常大的影响。在简要归纳动力电池组热管理必要性和系统功能的前提下,从电池最优工作温度范围、热场计算、温度传感器布置、风机功率选择和电池包设计等几个方面介绍了动力电池组热管理系统的设计要点,并对不同冷却方式进行对比分析,为后续研究提供参考。%Compared with the traditional fuel vehicle,electric vehicle had advantages on more effective and more clear.The electric vehicle's performance was mostly decided by battery's performance.As the main influence factor of battery's performance,battery temperature had significant effect on electric vehicle's usability and safety.On the basis of briefly summarizing the necessity and function of power battery thermal management system,this paper introduced the key design points of battery thermal management system from optimum operating temperature range,heat field calculation,temperature sensor decorate,fan power selection and battery pack design.Then analyzed different cooling systems,provided a reference for further research.

  15. A High-Gain Three-Port Power Converter with Fuel Cell, Battery Sources and Stacked Output for Hybrid Electric Vehicles and DC-Microgrids

    OpenAIRE

    Ching-Ming Lai; Ming-Ji Yang

    2016-01-01

    This paper proposes a novel high-gain three-port power converter with fuel cell (FC), battery sources and stacked output for a hybrid electric vehicle (HEV) connected to a dc-microgrid. In the proposed power converter, the load power can be flexibly distributed between the input sources. Moreover, the charging or discharging of the battery storage device can be controlled effectively using the FC source. The proposed converter has several outputs in series to achieve a high-voltage output, wh...

  16. Heat transfer and thermal management studies of lithium polymer batteries for electric vehicle applications

    Science.gov (United States)

    Song, Li

    The thermal conductivities of the polymer electrolyte and composite cathode are important parameters characterizing heat transport in lithium polymer batteries. The thermal conductivities of lithium polymer electrolytes, including poly-ethylene oxide (PEO), PEO-LiClO4, PEO-LiCF3SO 3, PEO-LiN(CF3SO2)2, PEO-LiC(CF 3SO2)3, and the thermal conductivities of TiS 2 and V6O13 composite cathodes, were measured over the temperature range from 25°C to 150°C by a guarded heat flow meter. The thermal conductivities of the electrolytes were found to be relatively constant for the temperature and for electrolytes with various concentrations of the lithium salt. The thermal conductivities of the composite cathodes were found to increase with the temperature below the melting temperature of the polymer electrolyte and only slightly increase above the melting temperature. Three different lithium polymer cells, including Li/PEO-LiCF3 S O3/TiS2, Li/PEO-LiC(CF3 S O2)3/V6 O13, and Li/PEO-LiN(CF3 S O2)2/ Li1+x Mn2 O4 were prepared and their discharge curves, along with heat generation rates, were measured at various galvanostatic discharge current densities, and at different temperature (70°C, 80°C and 90°C), by a potentiostat/galvanostat and an isothermal microcalorimeter. The thermal stability of a lithium polymer battery was examined by a linear perturbation analysis. In contrast to the thermal conductivity, the ionic conductivity of polymer electrolytes for lithium-polymer cell increases greatly with increasing temperature, an instability could arise from this temperature dependence. The numerical calculations, using a two dimensional thermal model, were carried out for constant potential drop across the electrolyte, for constant mean current density and for constant mean cell output power. The numerical calculations were approximately in agreement with the linear perturbation analysis. A coupled mathematical model, including electrochemical and thermal components, was

  17. A control-oriented lithium-ion battery pack model for plug-in hybrid electric vehicle cycle-life studies and system design with consideration of health management

    Science.gov (United States)

    Cordoba-Arenas, Andrea; Onori, Simona; Rizzoni, Giorgio

    2015-04-01

    A crucial step towards the large-scale introduction of plug-in hybrid electric vehicles (PHEVs) in the market is to reduce the cost of its battery systems. Currently, battery cycle- and calendar-life represents one of the greatest uncertainties in the total life-cycle cost of battery systems. The field of battery aging modeling and prognosis has seen progress with respect to model-based and data-driven approaches to describe the aging of battery cells. However, in real world applications cells are interconnected and aging propagates. The propagation of aging from one cell to others exhibits itself in a reduced battery system life. This paper proposes a control-oriented battery pack model that describes the propagation of aging and its effect on the life span of battery systems. The modeling approach is such that it is able to predict pack aging, thermal, and electrical dynamics under actual PHEV operation, and includes consideration of random variability of the cells, electrical topology and thermal management. The modeling approach is based on the interaction between dynamic system models of the electrical and thermal dynamics, and dynamic models of cell aging. The system-level state-of-health (SOH) is assessed based on knowledge of individual cells SOH, pack electrical topology and voltage equalization approach.

  18. A field operational test on valve-regulated lead-acid absorbent-glass-mat batteries in micro-hybrid electric vehicles. Part II. Results based on multiple regression analysis and tear-down analysis

    Science.gov (United States)

    Schaeck, S.; Karspeck, T.; Ott, C.; Weirather-Koestner, D.; Stoermer, A. O.

    2011-03-01

    In the first part of this work [1] a field operational test (FOT) on micro-HEVs (hybrid electric vehicles) and conventional vehicles was introduced. Valve-regulated lead-acid (VRLA) batteries in absorbent glass mat (AGM) technology and flooded batteries were applied. The FOT data were analyzed by kernel density estimation. In this publication multiple regression analysis is applied to the same data. Square regression models without interdependencies are used. Hereby, capacity loss serves as dependent parameter and several battery-related and vehicle-related parameters as independent variables. Battery temperature is found to be the most critical parameter. It is proven that flooded batteries operated in the conventional power system (CPS) degrade faster than VRLA-AGM batteries in the micro-hybrid power system (MHPS). A smaller number of FOT batteries were applied in a vehicle-assigned test design where the test battery is repeatedly mounted in a unique test vehicle. Thus, vehicle category and specific driving profiles can be taken into account in multiple regression. Both parameters have only secondary influence on battery degradation, instead, extended vehicle rest time linked to low mileage performance is more serious. A tear-down analysis was accomplished for selected VRLA-AGM batteries operated in the MHPS. Clear indications are found that pSoC-operation with periodically fully charging the battery (refresh charging) does not result in sulphation of the negative electrode. Instead, the batteries show corrosion of the positive grids and weak adhesion of the positive active mass.

  19. Modeling and control of a power converter for electric vehicle integrating battery charging function

    OpenAIRE

    Lacroix, Samantha

    2013-01-01

    Environmental constraints and reduction of fossil fuels resources have led industrials and laboratories to search for alternative solutions in the transportation domain. For the last few years, several vehicles or planes functions have been gradually electrified, up to their complete electrification. This thesis presents an AC/DC converter integrated in an Electric Vehicle (EV) for the charger application. The conversion is realized by using the electric traction powertrain, in order to reduc...

  20. Optimal Scheduling of a Battery Energy Storage System with Electric Vehicles’ Auxiliary for a Distribution Network with Renewable Energy Integration

    Directory of Open Access Journals (Sweden)

    Yuqing Yang

    2015-09-01

    Full Text Available With global conventional energy depletion, as well as environmental pollution, utilizing renewable energy for power supply is the only way for human beings to survive. Currently, distributed generation incorporated into a distribution network has become the new trend, with the advantages of controllability, flexibility and tremendous potential. However, the fluctuation of distributed energy resources (DERs is still the main concern for accurate deployment. Thus, a battery energy storage system (BESS has to be involved to mitigate the bad effects of DERs’ integration. In this paper, optimal scheduling strategies for BESS operation have been proposed, to assist with consuming the renewable energy, reduce the active power loss, alleviate the voltage fluctuation and minimize the electricity cost. Besides, the electric vehicles (EVs considered as the auxiliary technique are also introduced to attenuate the DERs’ influence. Moreover, both day-ahead and real-time operation scheduling strategies were presented under the consideration with the constraints of BESS and the EVs’ operation, and the optimization was tackled by a fuzzy mathematical method and an improved particle swarm optimization (IPSO algorithm. Furthermore, the test system for the proposed strategies is a real distribution network with renewable energy integration. After simulation, the proposed scheduling strategies have been verified to be extremely effective for the enhancement of the distribution network characteristics.

  1. A Study of Fuel Economy Improvement in a Plug-in Hybrid Electric Vehicle using Engine on/off and Battery Charging Power Control Based on Driver Characteristics

    Directory of Open Access Journals (Sweden)

    Seulgi Lee

    2015-09-01

    Full Text Available In this study, driving data for various types of drivers are collected using a VIDE (virtual integrated driving environment, and a driver model is developed. To represent the driver tendencies quantitatively, the DDA (degree of driver aggression is proposed based on fuzzy logic. DDA has a 0-1 value; the closer the DDA is to one, the more aggressive the driver. Using the DDA, an engine on/off and battery charging power control algorithm are developed to improve the fuel economy of a power-split-type plug-in hybrid electric vehicle. The engine on/off control reduces the frequent engine on/off caused by aggressive driving, whereas the battery charging power control maintains the battery state of charge (SOC by operating the engine according to the DDA. It is found that the proposed control algorithm improves fuel economy by 17.3% compared to the existing control for an aggressive driver.

  2. Investigation of the Storage Behavior of Shredded Lithium-Ion Batteries from Electric Vehicles for Recycling Purposes.

    Science.gov (United States)

    Grützke, Martin; Krüger, Steffen; Kraft, Vadim; Vortmann, Britta; Rothermel, Sergej; Winter, Martin; Nowak, Sascha

    2015-10-26

    Shredding of the cells is often the first step in lithium-ion battery (LIB) recycling. Thus, LiNi1/3 Mn1/3 Co1/3 O2 (NMC)/graphite lithium-ion cells from a field-tested electric vehicle were shredded and transferred to tinplate or plastic storage containers. The formation of hazardous compounds within, and being released from, these containers was monitored over 20 months. The tinplate cans underwent fast corrosion as a result of either residual charge in the active battery material, which could not fully be discharged because of contact loss to the current collector, or redox reactions between the tinplate surface and metal parts of the shredded material. The headspace compositions of the containers were investigated at room temperature and 150 °C using headspace-gas chromatography-mass spectrometry (HS-GC-MS). Samples of the waste material were also collected using microwave-assisted extraction and the extracts were analyzed over a period of 20 months using ion chromatography-electrospray ionization-mass spectrometry (IC-ESI-MS). LiPF6 was identified as a conducting salt, whereas dimethyl carbonate, ethyl methyl carbonate, and ethylene carbonate were the main solvent components. Cyclohexylbenzene was also detected, which is an additive for overcharge protection. Diethyl carbonate, fluoride, difluorophosphate and several ionic and non-ionic alkyl (fluoro)phosphates were also identified. Importantly, dimethyl fluorophosphate (DMFP) and diethyl fluorophosphate (DEFP) were quantified using HS-GC-MS through the use of an internal standard. DMFP, DEFP, and related compounds are known as chemical warfare agents, and the presence of these materials is of great interest. In the case of this study, these hazardous materials are present but in manageable low concentrations. Nonetheless, the presence of such compounds and their potential release during an accident that may occur during shredding or recycling of large amounts of LIB waste should be considered.

  3. Investigation of the Storage Behavior of Shredded Lithium-Ion Batteries from Electric Vehicles for Recycling Purposes.

    Science.gov (United States)

    Grützke, Martin; Krüger, Steffen; Kraft, Vadim; Vortmann, Britta; Rothermel, Sergej; Winter, Martin; Nowak, Sascha

    2015-10-26

    Shredding of the cells is often the first step in lithium-ion battery (LIB) recycling. Thus, LiNi1/3 Mn1/3 Co1/3 O2 (NMC)/graphite lithium-ion cells from a field-tested electric vehicle were shredded and transferred to tinplate or plastic storage containers. The formation of hazardous compounds within, and being released from, these containers was monitored over 20 months. The tinplate cans underwent fast corrosion as a result of either residual charge in the active battery material, which could not fully be discharged because of contact loss to the current collector, or redox reactions between the tinplate surface and metal parts of the shredded material. The headspace compositions of the containers were investigated at room temperature and 150 °C using headspace-gas chromatography-mass spectrometry (HS-GC-MS). Samples of the waste material were also collected using microwave-assisted extraction and the extracts were analyzed over a period of 20 months using ion chromatography-electrospray ionization-mass spectrometry (IC-ESI-MS). LiPF6 was identified as a conducting salt, whereas dimethyl carbonate, ethyl methyl carbonate, and ethylene carbonate were the main solvent components. Cyclohexylbenzene was also detected, which is an additive for overcharge protection. Diethyl carbonate, fluoride, difluorophosphate and several ionic and non-ionic alkyl (fluoro)phosphates were also identified. Importantly, dimethyl fluorophosphate (DMFP) and diethyl fluorophosphate (DEFP) were quantified using HS-GC-MS through the use of an internal standard. DMFP, DEFP, and related compounds are known as chemical warfare agents, and the presence of these materials is of great interest. In the case of this study, these hazardous materials are present but in manageable low concentrations. Nonetheless, the presence of such compounds and their potential release during an accident that may occur during shredding or recycling of large amounts of LIB waste should be considered. PMID

  4. 电动汽车电池箱检测工装的结构设计%Structure Design of Battery Box Test Equipment of Electric Car

    Institute of Scientific and Technical Information of China (English)

    崔庆东; 丁丽平; 郭炎杰; 李明道

    2013-01-01

    T he current electric vehicle battery boxes are made of manual inspection and have no battery or load block w hen detectingin the actual situation .In case of this ,this article presents a fully automatic battery box testing equipmentand a detailed statement of the test fixture design process and the typical program .By ana-lysing the advantages and disadvantages of the various options ,it ultimately designs a generic battery box testing automation equipment in this article .T he device implements the electric vehicle battery box automatic testing and evaluation ,w hich can not only reduce the labors intensity ,improve the reliability of the product testing ,credibility and the pre -qualified rate of battery box ,but also greatlyimprove the working efficiency and fill the gap of the industry .%针对目前电动汽车动力电池箱均采用人工检测且检测时不匹配电池或载重块的实际情况,提出了一种全自动化的电池箱检测工装,并详细陈述了检测工装的设计过程及典型方案,通过分析各个方案的优缺点,最终设计出了一种通用的自动化电池箱检测工装;该检测工装实现了电动汽车电池箱自动化检测与评估,不仅减轻了工人的劳动强度,提高了产品检测的可靠性、可信性和电池箱出厂合格率,工作效率也得到了很大的提升,为行业填补了空白。

  5. Thermal Performance of Lithium-ion Battery in Electric Vehicles%电动汽车锂离子电池的生热特性

    Institute of Scientific and Technical Information of China (English)

    辛明华; 余楚礼; 车杜兰

    2012-01-01

    Research on thermal performance of Lithium-ion battery is the foundation of battery pack thermal management of electric vehicles. Taking a kind of Lithium-ion battery with 11A·h rated capacity applied on an electric vehicle, finite element modeling analysis is conducted, and thermal performance at different ambiance temperature is compared. Through experimental verification, simulation analysis is consistent with test results. At the ambiance temperature of-20 -40℃, the battery is stopping discharge by 1 C and temperature rise is above 20℃. It is indicated recommended working temperature of the battery is 30-55 ℃, heating system must be allocated in battery external, when the discharge rate is below 1 C, cooling system can not be allocated.%对锂离子电池生热特性的研究是电动汽车动力电池热管理设计的基础。文章以电动汽车用11A·h电池单体为例,进行有限元建模分析,比较了它在不同环境温度下的生热特性。经过试验验证,测试结果与仿真分析相符合,该电池在环境温度为-20~40℃时以1C放电终止,温升为20℃左右。指出由于该电池推荐工作温度为30~55℃,因此使用时电池外部应配有加热系统;当电池放电倍率始终小于1C时,可不配置强制冷却系统。

  6. A thermally regenerative ammonia-based battery for efficient harvesting of low-grade thermal energy as electrical power

    KAUST Repository

    Zhang, Fang

    2015-01-01

    © 2015 The Royal Society of Chemistry. Thermal energy was shown to be efficiently converted into electrical power in a thermally regenerative ammonia-based battery (TRAB) using copper-based redox couples [Cu(NH3)4 2+/Cu and Cu(ii)/Cu]. Ammonia addition to the anolyte (2 M ammonia in a copper-nitrate electrolyte) of a single TRAB cell produced a maximum power density of 115 ± 1 W m-2 (based on projected area of a single copper mesh electrode), with an energy density of 453 W h m-3 (normalized to the total electrolyte volume, under maximum power production conditions). Adding a second cell doubled both the voltage and maximum power. Increasing the anolyte ammonia concentration to 3 M further improved the maximum power density to 136 ± 3 W m-2. Volatilization of ammonia from the spent anolyte by heating (simulating distillation), and re-addition of this ammonia to the spent catholyte chamber with subsequent operation of this chamber as the anode (to regenerate copper on the other electrode), produced a maximum power density of 60 ± 3 W m-2, with an average discharge energy efficiency of ∼29% (electrical energy captured versus chemical energy in the starting solutions). Power was restored to 126 ± 5 W m-2 through acid addition to the regenerated catholyte to decrease pH and dissolve Cu(OH)2 precipitates, suggesting that an inexpensive acid or a waste acid could be used to improve performance. These results demonstrated that TRABs using ammonia-based electrolytes and inexpensive copper electrodes can provide a practical method for efficient conversion of low-grade thermal energy into electricity.

  7. Connected Ways and Spontaneous Combustion Fire of Battery Piles for Pure Electric City Bus%纯电动城市客车电池组的连接方式与自燃火灾

    Institute of Scientific and Technical Information of China (English)

    车兆华

    2012-01-01

    The author introduces some connected ways of battery piles for pure electric city bus, and analyzes the reasons of causing the batteries spontaneous combustion fire.%介绍纯电动客车动力电池组的几种连接方式,分析造成电池自燃火灾的原因。

  8. New logistical issues in using electric vehicle fleets with battery exchange infrastructure

    DEFF Research Database (Denmark)

    Mirchandani, Pitu; Adler, Jonathan; Madsen, Oli B.G.

    2014-01-01

    There is much reason to believe that fleets of service vehicles of many organizations will transform their vehicles that utilize alternative fuels that are more sustainable. The electric vehicle (EV) is a good candidate for this transformation, especially which "refuels" by exchanging its spent b...

  9. Online state of charge and model parameters estimation of the LiFePO4 battery in electric vehicles using multiple adaptive forgetting factors recursive least-squares

    Science.gov (United States)

    Duong, Van-Huan; Bastawrous, Hany Ayad; Lim, KaiChin; See, Khay Wai; Zhang, Peng; Dou, Shi Xue

    2015-11-01

    This paper deals with the contradiction between simplicity and accuracy of the LiFePO4 battery states estimation in the electric vehicles (EVs) battery management system (BMS). State of charge (SOC) and state of health (SOH) are normally obtained from estimating the open circuit voltage (OCV) and the internal resistance of the equivalent electrical circuit model of the battery, respectively. The difficulties of the parameters estimation arise from their complicated variations and different dynamics which require sophisticated algorithms to simultaneously estimate multiple parameters. This, however, demands heavy computation resources. In this paper, we propose a novel technique which employs a simplified model and multiple adaptive forgetting factors recursive least-squares (MAFF-RLS) estimation to provide capability to accurately capture the real-time variations and the different dynamics of the parameters whilst the simplicity in computation is still retained. The validity of the proposed method is verified through two standard driving cycles, namely Urban Dynamometer Driving Schedule and the New European Driving Cycle. The proposed method yields experimental results that not only estimated the SOC with an absolute error of less than 2.8% but also characterized the battery model parameters accurately.

  10. Research, development and demonstration of nickel-iron batteries for electric vehicle propulsion. Annual report, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-01

    The program has advanced to the level of full-size, prototype cell fabrication and evaluation. EPP nickel electrodes are now being prepared of up to 24 Ah/plate (at C/3 drain rate) at design thickness (2.5 mm). Iron electrodes of the composite-type are delivering 24 Ah/plate (at C/3) at target thickness (1.0 mm). Both plates are displaying good capacity stability at 130 to 175 test cycles, respectively, in some of the 3 plate cell tests. Finished cells are delivering up to 58 Wh/Kg at C/3, based on projected weight of the finished cell and in the actual designed cell volume. Reduction in cell resistance, reduction in nickel plate processing time and swelling on cycling are areas of major effort to reach the final battery objectives. Thermal nickel electrodes are showing promise in full size plate tests (up to 22 Ah in a plate of only 2.3 mm thickness) and will be evaluated in finished cells as soon as the technology shows repeatable results in full-size test plates.

  11. Battery-Powered Electric and Hybrid Electric Vehicle Projects to Reduce Greenhouse Gas Emissions: A Resource for Project Development

    Energy Technology Data Exchange (ETDEWEB)

    National Energy Technology Laboratory

    2002-07-31

    as requiring specific technology improvements or an increase in fuel efficiency. Site-specific project activities can also be undertaken to help decrease GHG emissions, although the use of such measures is less common. Sample activities include switching to less GHG-intensive vehicle options, such as electric vehicles (EVs) or hybrid electric vehicles (HEVs). As emissions from transportation activities continue to rise, it will be necessary to promote both types of abatement activities in order to reverse the current emissions path. This Resource Guide focuses on site- and project-specific transportation activities. .

  12. Fast Charging and Smart Charging Tests for Electric Vehicles Batteries Using Renewable Energy

    DEFF Research Database (Denmark)

    Forero Camacho, Oscar Mauricio; Mihet-Popa, Lucian

    2016-01-01

    Electric Vehicles (EV) technologies are still relatively new and under strong development. Although some standardized solutions are being promoted and becoming a new trend, there is an outstanding need for common platforms and sharing of knowledge and core technologies. This paper presents...... time the power system services, reducing the peak power and the energy losses in the power connection line of the power exchange with the national grid....

  13. Strategic Options for Azure Dynamics in Hybrid and Battery Electric Vehicle Markets

    OpenAIRE

    Finlay, James Gordon

    2012-01-01

    Azure Dynamics provides electric vehicle powertrain technology to commercial truck fleets in North America and Europe. Azure Dynamics is a firm in distress and fighting for survival, having filed for bankruptcy protection in March 2012. An analysis of commercial trucking markets reviews factors driving vehicle electrification and provides a market segmentation to find segments best suited to Azure’s technology. Porter’s Five Forces methodology is used to assess target market attractiveness an...

  14. Present Status and Development Trend of Batteries for Electric Vehicles%电动汽车电池的现状及发展趋势

    Institute of Scientific and Technical Information of China (English)

    宋永华; 阳岳希; 胡泽春

    2011-01-01

    电动汽车电池既是发展电动汽车的核心,更是电力工业与汽车行业的关键结合点.结合电动汽车的发展历史概述了车用动力电池的发展情况,重点介绍了3种主要电动汽车电池:铅酸电池、镍氢电池和锉离子电池的研究现状及当前的应用情况,并从电池化学性能和商业化的电动汽车电池组性能2个角度在技术和经济层面进行了详细的比较分析,最后对当前电动汽车电池的应用前景、未来发展趋势和研发中的新电池技术进行了展望,指出中国电力行业应关注电动汽车电池技术的发展,分析电动汽车充电负荷对电网的影响并及时采取应对措施.%With the advent of more stringent regulations related to emissions, energy resource constraints and financial crisis, the world has sparked a global race to electrify transportation. Battery is not only a key component of electric vehicles, but also plays a prominent role as the joint of power and automotive industry. This paper reviews improvements made in the design and manufacture of batteries as well as development of electric vehicles during the past decades. State of the art for three important battery technologies in EV application, namely lead-acid battery, NiMH battery and lithium-ion battery, as well as their current application are presented; and in the viewpoints of chemical propoties of the cell and the performances of commercial pack for EV, detailed comparative analyses in technology and economy are performed. The application outlook of EV battery, its development trend in future and new cell technologies being developed are prospected, and it is pointed out that the power sector of China should pay special attentions to the development of EV battery technology, analyze the influences of EV charging load on power grid and take steps in time.

  15. Decision making model for lifecycle assessment of lithium-ion battery for electric vehicle - A case study for smart electric bus project in Korea

    Science.gov (United States)

    Thein, Sabai; Chang, Yoon Seok

    2014-03-01

    Lithium-ion (Li-ion) battery is part of our everyday life. There are many automobiles invented today that operates by Li-ion batteries. The issue with batteries is that they lose capacity and reliability over time as they are charged and discharged. This paper introduces a lifecycle assessment system for Li-ion EV battery considering the condition of each battery which helps decision making. The proposed research concerns not only for the ad-hoc condition but also regular condition of the Li-ion EV battery. We apply the Markov Decision Process (MDP) with selected policies for the measurement of each stage probability. The result shows that we could monitor product aging status with the proposed algorithm. It also shows that the calculated product life span was longer than the general warranty time period.

  16. A Method to Simultaneously Detect the Current Sensor Fault and Estimate the State of Energy for Batteries in Electric Vehicles.

    Science.gov (United States)

    Xu, Jun; Wang, Jing; Li, Shiying; Cao, Binggang

    2016-01-01

    Recently, State of energy (SOE) has become one of the most fundamental parameters for battery management systems in electric vehicles. However, current information is critical in SOE estimation and current sensor is usually utilized to obtain the latest current information. However, if the current sensor fails, the SOE estimation may be confronted with large error. Therefore, this paper attempts to make the following contributions: Current sensor fault detection and SOE estimation method is realized simultaneously. Through using the proportional integral observer (PIO) based method, the current sensor fault could be accurately estimated. By taking advantage of the accurate estimated current sensor fault, the influence caused by the current sensor fault can be eliminated and compensated. As a result, the results of the SOE estimation will be influenced little by the fault. In addition, the simulation and experimental workbench is established to verify the proposed method. The results indicate that the current sensor fault can be estimated accurately. Simultaneously, the SOE can also be estimated accurately and the estimation error is influenced little by the fault. The maximum SOE estimation error is less than 2%, even though the large current error caused by the current sensor fault still exists. PMID:27548183

  17. Design and Control of a Multi-Functional Energy Recovery Power Accumulator Battery Pack Testing System for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Bo Long

    2014-03-01

    Full Text Available In this paper, aiming at the energy loss and harmonic problems in the conventional power accumulator battery pack testing system (PABPTS, an improved multi-functional energy recovery PABPTS (ERPABPTS for electric vehicles (EVs was proposed. The improved system has the functions of harmonic detection, suppression, reactive compensation and energy recovery. The ERPABPTS, which contains a bi-directional buck-boost direct current (DC-DC converter and a bi-directional alternating current (AC-DC converter with an inductor-capacitor-inductor (LCL type filter interfacing to the AC-grid, is proposed. System configuration and operation principle of the combined system are discussed first, then, the reactive compensation and harmonic suppression controller under balanced grid-voltage condition are presented. Design of a fourth order band-pass Butterworth filter for current harmonic detection is put forward, and the reactive compensator design procedure considering the non-linear load is also illustrated. The proposed scheme is implemented in a 175-kW prototype in the laboratory. Simulation and experimental results show that the combined configuration can effectively realize energy recovery for high accuracy current test requirement, meanwhile, can effectively achieve reactive compensation and current harmonic suppression.

  18. Optimal Operation and Management for Smart Grid Subsumed High Penetration of Renewable Energy, Electric Vehicle, and Battery Energy Storage System

    Science.gov (United States)

    Shigenobu, Ryuto; Noorzad, Ahmad Samim; Muarapaz, Cirio; Yona, Atsushi; Senjyu, Tomonobu

    2016-04-01

    Distributed generators (DG) and renewable energy sources have been attracting special attention in distribution systems in all over the world. Renewable energies, such as photovoltaic (PV) and wind turbine generators are considered as green energy. However, a large amount of DG penetration causes voltage deviation beyond the statutory range and reverse power flow at interconnection points in the distribution system. If excessive voltage deviation occurs, consumer's electric devices might break and reverse power flow will also has a negative impact on the transmission system. Thus, mass interconnections of DGs has an adverse effect on both of the utility and the customer. Therefore, reactive power control method is proposed previous research by using inverters attached DGs for prevent voltage deviations. Moreover, battery energy storage system (BESS) is also proposed for resolve reverse power flow. In addition, it is possible to supply high quality power for managing DGs and BESSs. Therefore, this paper proposes a method to maintain voltage, active power, and reactive power flow at interconnection points by using cooperative controlled of PVs, house BESSs, EVs, large BESSs, and existing voltage control devices. This paper not only protect distribution system, but also attain distribution loss reduction and effectivity management of control devices. Therefore mentioned control objectives are formulated as an optimization problem that is solved by using the Particle Swarm Optimization (PSO) algorithm. Modified scheduling method is proposed in order to improve convergence probability of scheduling scheme. The effectiveness of the proposed method is verified by case studies results and by using numerical simulations in MATLAB®.

  19. A Method to Simultaneously Detect the Current Sensor Fault and Estimate the State of Energy for Batteries in Electric Vehicles.

    Science.gov (United States)

    Xu, Jun; Wang, Jing; Li, Shiying; Cao, Binggang

    2016-08-19

    Recently, State of energy (SOE) has become one of the most fundamental parameters for battery management systems in electric vehicles. However, current information is critical in SOE estimation and current sensor is usually utilized to obtain the latest current information. However, if the current sensor fails, the SOE estimation may be confronted with large error. Therefore, this paper attempts to make the following contributions: Current sensor fault detection and SOE estimation method is realized simultaneously. Through using the proportional integral observer (PIO) based method, the current sensor fault could be accurately estimated. By taking advantage of the accurate estimated current sensor fault, the influence caused by the current sensor fault can be eliminated and compensated. As a result, the results of the SOE estimation will be influenced little by the fault. In addition, the simulation and experimental workbench is established to verify the proposed method. The results indicate that the current sensor fault can be estimated accurately. Simultaneously, the SOE can also be estimated accurately and the estimation error is influenced little by the fault. The maximum SOE estimation error is less than 2%, even though the large current error caused by the current sensor fault still exists.

  20. A Method to Simultaneously Detect the Current Sensor Fault and Estimate the State of Energy for Batteries in Electric Vehicles

    Science.gov (United States)

    Xu, Jun; Wang, Jing; Li, Shiying; Cao, Binggang

    2016-01-01

    Recently, State of energy (SOE) has become one of the most fundamental parameters for battery management systems in electric vehicles. However, current information is critical in SOE estimation and current sensor is usually utilized to obtain the latest current information. However, if the current sensor fails, the SOE estimation may be confronted with large error. Therefore, this paper attempts to make the following contributions: Current sensor fault detection and SOE estimation method is realized simultaneously. Through using the proportional integral observer (PIO) based method, the current sensor fault could be accurately estimated. By taking advantage of the accurate estimated current sensor fault, the influence caused by the current sensor fault can be eliminated and compensated. As a result, the results of the SOE estimation will be influenced little by the fault. In addition, the simulation and experimental workbench is established to verify the proposed method. The results indicate that the current sensor fault can be estimated accurately. Simultaneously, the SOE can also be estimated accurately and the estimation error is influenced little by the fault. The maximum SOE estimation error is less than 2%, even though the large current error caused by the current sensor fault still exists. PMID:27548183

  1. 大倍率放电时电动汽车用锂离子电池的热性能%Electrical and thermal performances of lithium-ion battery for electric vehicle at high discharge rate

    Institute of Scientific and Technical Information of China (English)

    张云云; 白洁; 张国庆

    2015-01-01

    为保证锂离子动力电池安全、可靠和高效的运行,实验研究了其在大倍率放电时的热性能。实验中,对于一款商业电动车用3.2 V、50 Ah锂离子电池,用充放电测试仪和温湿度巡检仪,控制放电倍率为1C~3C(50~150 A)。结果表明:电池放电倍率越大,电池两端工作电压平台越低,电池放电量越小,电池表面的温升率越大。当放电倍率达到3C (150A)时,电池表面温度超出其安全工作温度,因而,锂离子动力电池在大倍率放电时,需要为其增加散热设备。拟合了一组用于计算不同放电倍率下电池的瞬时产热量的经验公式。这些公式可用于锂离子动力电池的辅助散热设备的设计和选择。%The electrical and thermal performances of power lithium-ion batteries used in electric vehicles were experimentaly investigated to guarantee the power lithium ion battery operate safely, reliably and efifciently. A charge and discharge tester and a temperature / humidity recorder were used to control the various rate of discharge at the arrange of 1C~3C (50~150 A) for a kind of 3.2 V/50 Ah lithium-ion power batteries commercial applied. The test results show that the operator voltage platform between battery two ends is going to lower with the output energy decreasing and the battery surface temperatures increasing when the discharged rate increases. The temperature at the lithium-ion battery surface exceeds the temperature limit for battery safely operating when the battery discharged rate up to 3C rate (or 150 A). Therefore, being equipped with cooling device is necessary for battery to ensure battery operate safely and efifciently. A group of empirical formulae was iftted for the battery transient heat production battery at various battery discharge rate. The formulas can be used to design and select auxiliary cooling devices for power lithium-ion batteries.

  2. Self-Charged Graphene Battery Harvests Electricity from Thermal Energy of the Environment

    OpenAIRE

    Xu, Zihan; Tai, Guoan; Zhou, Yungang; Gao, Fei; Wong, Kin Hung

    2012-01-01

    The energy of ionic thermal motion presents universally, which is as high as 4 kJ\\bullet kg-1\\bullet K-1 in aqueous solution, where thermal velocity of ions is in the order of hundreds of meters per second at room temperature1,2. Moreover, the thermal velocity of ions can be maintained by the external environment, which means it is unlimited. However, little study has been reported on converting the ionic thermal energy into electricity. Here we present a graphene device with asymmetric elect...

  3. Organo-sulfur molecules enable iron-based battery electrodes to meet the challenges of large-scale electrical energy storage

    Energy Technology Data Exchange (ETDEWEB)

    Yang, B; Malkhandi, S; Manohar, AK; Prakash, GKS; Narayanan, SR

    2014-07-03

    Rechargeable iron-air and nickel-iron batteries are attractive as sustainable and inexpensive solutions for large-scale electrical energy storage because of the global abundance and eco-friendliness of iron, and the robustness of iron-based batteries to extended cycling. Despite these advantages, the commercial use of iron-based batteries has been limited by their low charging efficiency. This limitation arises from the iron electrodes evolving hydrogen extensively during charging. The total suppression of hydrogen evolution has been a significant challenge. We have found that organo-sulfur compounds with various structural motifs (linear and cyclic thiols, dithiols, thioethers and aromatic thiols) when added in milli-molar concentration to the aqueous alkaline electrolyte, reduce the hydrogen evolution rate by 90%. These organo-sulfur compounds form strongly adsorbed layers on the iron electrode and block the electrochemical process of hydrogen evolution. The charge-transfer resistance and double-layer capacitance of the iron/electrolyte interface confirm that the extent of suppression of hydrogen evolution depends on the degree of surface coverage and the molecular structure of the organo-sulfur compound. An unanticipated electrochemical effect of the adsorption of organo-sulfur molecules is "de-passivation" that allows the iron electrode to be discharged at high current values. The strongly adsorbed organo-sulfur compounds were also found to resist electro-oxidation even at the positive electrode potentials at which oxygen evolution can occur. Through testing on practical rechargeable battery electrodes we have verified the substantial improvements to the efficiency during charging and the increased capability to discharge at high rates. We expect these performance advances to enable the design of efficient, inexpensive and eco-friendly iron-based batteries for large-scale electrical energy storage.

  4. Estimation method of state-of-charge for lithium-ion battery used in hybrid electric vehicles based on variable structure extended kalman filter

    Science.gov (United States)

    Sun, Yong; Ma, Zilin; Tang, Gongyou; Chen, Zheng; Zhang, Nong

    2016-03-01

    Since the main power source of hybrid electric vehicle(HEV) is supplied by the power battery, the predicted performance of power battery, especially the state-of-charge(SOC) estimation has attracted great attention in the area of HEV. However, the value of SOC estimation could not be greatly precise so that the running performance of HEV is greatly affected. A variable structure extended kalman filter(VSEKF)-based estimation method, which could be used to analyze the SOC of lithium-ion battery in the fixed driving condition, is presented. First, the general lower-order battery equivalent circuit model(GLM), which includes column accumulation model, open circuit voltage model and the SOC output model, is established, and the off-line and online model parameters are calculated with hybrid pulse power characteristics(HPPC) test data. Next, a VSEKF estimation method of SOC, which integrates the ampere-hour(Ah) integration method and the extended Kalman filter(EKF) method, is executed with different adaptive weighting coefficients, which are determined according to the different values of open-circuit voltage obtained in the corresponding charging or discharging processes. According to the experimental analysis, the faster convergence speed and more accurate simulating results could be obtained using the VSEKF method in the running performance of HEV. The error rate of SOC estimation with the VSEKF method is focused in the range of 5% to 10% comparing with the range of 20% to 30% using the EKF method and the Ah integration method. In Summary, the accuracy of the SOC estimation in the lithium-ion battery cell and the pack of lithium-ion battery system, which is obtained utilizing the VSEKF method has been significantly improved comparing with the Ah integration method and the EKF method. The VSEKF method utilizing in the SOC estimation in the lithium-ion pack of HEV can be widely used in practical driving conditions.

  5. Estimation Method of State-of-Charge For Lithium-ion Battery Used in Hybrid Electric Vehicles Based on Variable Structure Extended Kalman Filter

    Institute of Scientific and Technical Information of China (English)

    SUN Yong; MA Zilin; TANG Gongyou; CHEN Zheng; ZHANG Nong

    2016-01-01

    Since the main power source of hybrid electric vehicle(HEV) is supplied by the power battery, the predicted performance of power battery, especially the state-of-charge(SOC) estimation has attracted great attention in the area of HEV. However, the value of SOC estimation could not be greatly precise so that the running performance of HEV is greatly affected. A variable structure extended kalman filter(VSEKF)-based estimation method, which could be used to analyze the SOC of lithium-ion battery in the fixed driving condition, is presented. First, the general lower-order battery equivalent circuit model(GLM), which includes column accumulation model, open circuit voltage model and the SOC output model, is established, and the off-line and online model parameters are calculated with hybrid pulse power characteristics(HPPC) test data. Next, a VSEKF estimation method of SOC, which integrates the ampere-hour(Ah) integration method and the extended Kalman filter(EKF) method, is executed with different adaptive weighting coefficients, which are determined according to the different values of open-circuit voltage obtained in the corresponding charging or discharging processes. According to the experimental analysis, the faster convergence speed and more accurate simulating results could be obtained using the VSEKF method in the running performance of HEV. The error rate of SOC estimation with the VSEKF method is focused in the range of 5%to 10%comparing with the range of 20%to 30%using the EKF method and the Ah integration method. In Summary, the accuracy of the SOC estimation in the lithium-ion battery cell and the pack of lithium-ion battery system, which is obtained utilizing the VSEKF method has been significantly improved comparing with the Ah integration method and the EKF method. The VSEKF method utilizing in the SOC estimation in the lithium-ion pack of HEV can be widely used in practical driving conditions.

  6. Estimation method of state-of-charge for lithium-ion battery used in hybrid electric vehicles based on variable structure extended kalman filter

    Science.gov (United States)

    Sun, Yong; Ma, Zilin; Tang, Gongyou; Chen, Zheng; Zhang, Nong

    2016-07-01

    Since the main power source of hybrid electric vehicle(HEV) is supplied by the power battery, the predicted performance of power battery, especially the state-of-charge(SOC) estimation has attracted great attention in the area of HEV. However, the value of SOC estimation could not be greatly precise so that the running performance of HEV is greatly affected. A variable structure extended kalman filter(VSEKF)-based estimation method, which could be used to analyze the SOC of lithium-ion battery in the fixed driving condition, is presented. First, the general lower-order battery equivalent circuit model(GLM), which includes column accumulation model, open circuit voltage model and the SOC output model, is established, and the off-line and online model parameters are calculated with hybrid pulse power characteristics(HPPC) test data. Next, a VSEKF estimation method of SOC, which integrates the ampere-hour(Ah) integration method and the extended Kalman filter(EKF) method, is executed with different adaptive weighting coefficients, which are determined according to the different values of open-circuit voltage obtained in the corresponding charging or discharging processes. According to the experimental analysis, the faster convergence speed and more accurate simulating results could be obtained using the VSEKF method in the running performance of HEV. The error rate of SOC estimation with the VSEKF method is focused in the range of 5% to 10% comparing with the range of 20% to 30% using the EKF method and the Ah integration method. In Summary, the accuracy of the SOC estimation in the lithium-ion battery cell and the pack of lithium-ion battery system, which is obtained utilizing the VSEKF method has been significantly improved comparing with the Ah integration method and the EKF method. The VSEKF method utilizing in the SOC estimation in the lithium-ion pack of HEV can be widely used in practical driving conditions.

  7. Design on CAN Network Project for Pure Electric Bus with Power Battery Replacement%换电式纯电动客车CAN网络方案设计

    Institute of Scientific and Technical Information of China (English)

    房永强

    2015-01-01

    结合某款换电式纯电动客车的研发与应用,介绍一种换电式纯电动客车三级CAN网络架构,以及合理的纯电动系统CAN总线管理方案。%Taking the R&D and application of a pure electric bus with the power battery replacement as an example, the author introduces a three-level CAN network architecture and appropriate management project of the control system based on the CAN bus of the pure electric system.

  8. A Desalination Battery

    KAUST Repository

    Pasta, Mauro

    2012-02-08

    Water desalination is an important approach to provide fresh water around the world, although its high energy consumption, and thus high cost, call for new, efficient technology. Here, we demonstrate the novel concept of a "desalination battery", which operates by performing cycles in reverse on our previously reported mixing entropy battery. Rather than generating electricity from salinity differences, as in mixing entropy batteries, desalination batteries use an electrical energy input to extract sodium and chloride ions from seawater and to generate fresh water. The desalination battery is comprised by a Na 2-xMn 5O 10 nanorod positive electrode and Ag/AgCl negative electrode. Here, we demonstrate an energy consumption of 0.29 Wh l -1 for the removal of 25% salt using this novel desalination battery, which is promising when compared to reverse osmosis (∼ 0.2 Wh l -1), the most efficient technique presently available. © 2012 American Chemical Society.

  9. Research, development and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-01

    This is the first annual report of progress achieved under ANL Contract 31-109-38-4248. It covers the report period from 15 March 1978 to 15 August 1978. The nickel electrode development program is directed at the optimization of the electrical performance, specifically, in terms of increased cycle life. The work concentrated upon both the development of pilot plant facilities to produce nickel hydroxide and upon optimizing the manufacturing processes to produce nickel hydroxide which has high electrochemical utilization. The primary goal of the zinc electrode studies is to increase the cycle life of this electrode. This effort is primarily concentrating on the effect of additives upon shape change and cycle performance and on the mechanistic processes involved in the shape change. The separator effort has as its major goal the development of a low-cost separator which exhibits stability in the electrolyte, has uniform pores which are of a sufficiently small size to impede the growth of zinc dendrites, and exhibits low electrical resistance and good flexibility. The process itself is now optimized for pilot plant manufacture; hundreds of formulations have been produced and subsequently screened in both the laboratory and in actual cells. Promising formulations are presently being subjected to additional characterization tests and life cycles. The goal of the sealed cell studies is to determine the feasibility of sealed-cell operation. Large numbers of 20-Ah cells have been subjected to accelerated testing. These cells incorporated separator variations, active material additives, and internal design variations. Cycle lives up to 150 deep cycles were achieved. Cell failure modes are analyzed. 51 figures, 20 tables.

  10. Development program of electrical vehicles of batteries in the UNAM; Programa de desarrollo de vehiculos electricos de baterias en la UNAM

    Energy Technology Data Exchange (ETDEWEB)

    Carmona Paredes, G.; Chicurel Uziel, R.; Chicurel Uziel, E.; Gutierrez Martinez, F. [Instituto de Ingenieria, UNAM, Mexico, D.F. (Mexico)

    2002-09-01

    Eight years ago, project to develop a small battery powered electric bus, known today as UNAM's Electric Vehicle, was started at the Engineering Institute. This project was followed by the design and construction, under an agreement with the Mexico City Government, of the Electrobus, a public transport vehicle that was recently put in operation and is being evaluated by the City's Electric Transportation Service. Two other projects, within the scope of UNAM's Electric Vehicle Development Program refer to light trucks: the Electrovira, characterized by exceptional maneuverability, and the Electric Delivery Vehicle. These projects are being carried out respectively by the Engineering Institute and the School of Engineering's Center for Design and Manufacture. Other parties that have collaborated in the program are: the School of Architecture's Center for Research in Industrial Design, the Instruments Center, and the School of Chemistry. Work is also being done on complementary aspects which include the development of an intelligent charger for large battery packs and of a dual electronic controller, a study of the dynamic performance of lead-acid batteries, the design of a battery monitoring system, and the search for new battery alternatives. [Spanish] Hace ocho anos, el Instituto de Ingenieria inicio el proyecto de desarrollo de un minibus electrico de baterias, conocido ahora como el Vehiculo Electrico UNAM. Este proyecto fue seguido de un convenio con el Gobierno del Distrito Federal para el diseno y construccion del Electrobus, un vehiculo para transporte publico que recientemente fue puesto en operacion para ser evaluado por el Servicio de Transporte Electrico del DF. Dos proyectos mas, enmarcados dentro del Programa de Desarrollo de Vehiculos Electricos, se refieren a vehiculos ligeros de carga como el Electrovira, caracterizado por su gran maniobrabilidad y el Vehiculo Electrico de Reparto. Estos proyectos se realizan respectivamente

  11. Alkaline quinone flow battery.

    Science.gov (United States)

    Lin, Kaixiang; Chen, Qing; Gerhardt, Michael R; Tong, Liuchuan; Kim, Sang Bok; Eisenach, Louise; Valle, Alvaro W; Hardee, David; Gordon, Roy G; Aziz, Michael J; Marshak, Michael P

    2015-09-25

    Storage of photovoltaic and wind electricity in batteries could solve the mismatch problem between the intermittent supply of these renewable resources and variable demand. Flow batteries permit more economical long-duration discharge than solid-electrode batteries by using liquid electrolytes stored outside of the battery. We report an alkaline flow battery based on redox-active organic molecules that are composed entirely of Earth-abundant elements and are nontoxic, nonflammable, and safe for use in residential and commercial environments. The battery operates efficiently with high power density near room temperature. These results demonstrate the stability and performance of redox-active organic molecules in alkaline flow batteries, potentially enabling cost-effective stationary storage of renewable energy. PMID:26404834

  12. Research, development, and demonstration of lead-acid batteries for electric-vehicle propulsion. Annual report for 1982

    Energy Technology Data Exchange (ETDEWEB)

    Bowman, D.E.

    1983-08-01

    Research programs on lead-acid batteries are reported that cover active materials utilization, active material integrity, and some technical support projects. Processing problems were encountered and corrected. Components and materials, a lead-plastic composite grid, cell designs, and deliverables are described. Cell testing is discussed, as well as battery subsystems, including fuel gage, thermal management, and electrolyte circulation. (LEW)

  13. Lithium battery management system

    Science.gov (United States)

    Dougherty, Thomas J.

    2012-05-08

    Provided is a system for managing a lithium battery system having a plurality of cells. The battery system comprises a variable-resistance element electrically connected to a cell and located proximate a portion of the cell; and a device for determining, utilizing the variable-resistance element, whether the temperature of the cell has exceeded a predetermined threshold. A method of managing the temperature of a lithium battery system is also included.

  14. Optimal Velocity Control for a Battery Electric Vehicle Driven by Permanent Magnet Synchronous Motors

    Directory of Open Access Journals (Sweden)

    Dongbin Lu

    2014-01-01

    Full Text Available The permanent magnet synchronous motor (PMSM has high efficiency and high torque density. Field oriented control (FOC is usually used in the motor to achieve maximum efficiency control. In the electric vehicle (EV application, the PMSM efficiency model, combined with the EV and road load system model, is used to study the optimal energy-saving control strategy, which is significant for the economic operation of EVs. With the help of GPS, IMU, and other information technologies, the road conditions can be measured in advance. Based on this information, the optimal velocity of the EV driven by PMSM can be obtained through the analytical algorithm according to the efficiency model of PMSM and the vehicle dynamic model in simple road conditions. In complex road conditions, considering the dynamic characteristics, the economic operating velocity trajectory of the EV can be obtained through the dynamic programming (DP algorithm. Simulation and experimental results show that the minimum energy consumption and global energy optimization can be achieved when the EV operates in the economic operation area.

  15. Design of protection circuit for lithium battery used in electric bicycle%电动自行车锂电池组保护电路设计

    Institute of Scientific and Technical Information of China (English)

    许英杰; 孙郅佶; 李帆; 范贤光

    2012-01-01

    The lithium battery with superior performance is the development trend of the electric bicycle power, but needs a dedicated protection circuit to work with so as to ensure the safety and long-period operation. In this paper, a protection circuit board including S-8209A was designed for the lithium battery set with 4-parallel and 10-serial connection mode. It achieved the functions of overcharge protection, overdischarge protection, overcharge-overdischarge balance and overcurrent protection. The circuit has been already applied to the electric bikes with the lithium batteries.%为保证电动自行车锂电池组安全、长寿命的运行,需为其配备专用管理保护电路.为此,针对一款4并10串规格的锂电池组设计了一套保护电路板,采用S-8209A保护芯片,实现了过充电保护、过放电保护、电池充放电平衡、过电流保护、正常带载等功能,已被可靠应用于某款电动自行车的锂电池组中.

  16. Performances of a lithium-carbon ``lithium ion``battery for electric powered vehicle; Performances d`un accumulateur au lithium-carbone ``Lithium Ion`` pour vehicule electrique

    Energy Technology Data Exchange (ETDEWEB)

    Broussely, M.; Planchat, J.P.; Rigobert, G.; Virey, D.; Sarre, G. [SAFT, Advanced and Industrial Battery Group, 86 - Poitiers (France)

    1996-12-31

    The lithium battery, also called `lithium-carbon` or `lithium ion`, is today the most promising candidate that can reach the expected minimum traction performances of electric powered vehicles. Thanks to a more than 20 years experience on lithium generators and to a specific research program on lithium batteries, the SAFT company has developed a 100 Ah electrochemical system, and full-scale prototypes have been manufactured for this application. These prototypes use the Li{sub x}NiO{sub 2} lithiated graphite electrochemical pair and were tested in terms of their electrical performances. Energy characteristics of 125 Wh/kg and 265 Wh/dm{sup 3} could be obtained. The possibility of supplying a power greater than 200 W/kg, even at low temperature (-10 deg. C) has been demonstrated with these elements. A full battery set of about 20 kWh was built and its evaluation is in progress. It comprises the electronic control systems for the optimum power management during charge and output. (J.S.) 9 refs.

  17. Battery energy storage system

    NARCIS (Netherlands)

    Tol, C.S.P.; Evenblij, B.H.

    2009-01-01

    The ability to store electrical energy adds several interesting features to a ships distribution network, as silent power, peak shaving and a ride through in case of generator failure. Modern intrinsically safe Li-ion batteries bring these within reach. For this modern lithium battery applications t

  18. Multi-step constant-current charging method for electric vehicle, valve-regulated, lead/acid batteries during night time for load-levelling

    Energy Technology Data Exchange (ETDEWEB)

    Ikeya, Tomohiko; Mita, Yuichi; Ishihara, Kaoru [Central Research Inst. of Electric Power Industry, Tokyo (Japan); Sawada, Nobuyuki [Hokkaido Electric Power, Sapporo (Japan); Takagi, Sakae; Murakami, Jun-ichi [Tohoku Electric Power, Sendai (Japan); Kobayashi, Kazuyuki [Tokyo Electric Power, Yokohama (Japan); Sakabe, Tetsuya [Chubu Electric Power, Nagoya (Japan); Kousaka, Eiichi [Hokuriku Electric Power, Toyama (Japan); Yoshioka, Haruki [The Kansai Electric Power, Osaka (Japan); Kato, Satoru [The Chugoku Electric Power, Hiroshima (Japan); Yamashita, Masanori [Shikoku Research Inst., Takamatsu (Japan); Narisoko, Hayato [The Okinawa Electric Power, Naha (Japan); Nishiyama, Kazuo [The Central Electric Power Council, Tokyo (Japan); Adachi, Kazuyuki [Kyushu Electric Power, Fukuoka (Japan)

    1998-09-01

    For the popularization of electric vehicles (EVs), the conditions for charging EV batteries with available current patterns should allow complete charging in a short time, i.e., less than 5 to 8 h. Therefore, in this study, a new charging condition is investigated for the EV valve-regulated lead/acid battery system, which should allow complete charging of EV battery systems with multi-step constant currents in a much shorter time with longer cycle life and higher energy efficiency compared with two-step constant-current charging. Although a high magnitude of the first current in the two-step constant-current method prolongs cycle life by suppressing the softening of positive active material, too large a charging current magnitude degrades cells due to excess internal evolution of heat. A charging current magnitude of approximately 0.5 C is expected to prolong cycle life further. Three-step charging could also increase the magnitude of charging current in the first step without shortening cycle life. Four-or six-step constant-current methods could shorten the charging time to less than 5 h, as well as yield higher energy efficiency and enhanced cycle life of over 400 cycles compared with two-step charging with the first step current of 0.5 C. Investigation of the degradation mechanism of the batteries revealed that the conditions of multi-step constant-current charging suppressed softening of positive active material and sulfation of negative active material, but, unfortunately, advanced the corrosion of the grids in the positive plates. By adopting improved grids and cooling of the battery system, the multistep constant-current method may enhance the cycle life. (orig.)

  19. Button batteries

    Science.gov (United States)

    Swallowing batteries ... These devices use button batteries: Calculators Cameras Hearing aids Penlights Watches ... If a person puts the battery up their nose and breathes it further in, ... problems Cough Pneumonia (if the battery goes unnoticed) ...

  20. Online model-based estimation of state-of-charge and open-circuit voltage of lithium-ion batteries in electric vehicles

    International Nuclear Information System (INIS)

    This paper presents a method to estimate the state-of-charge (SOC) of a lithium-ion battery, based on an online identification of its open-circuit voltage (OCV), according to the battery’s intrinsic relationship between the SOC and the OCV for application in electric vehicles. Firstly an equivalent circuit model with n RC networks is employed modeling the polarization characteristic and the dynamic behavior of the lithium-ion battery, the corresponding equations are built to describe its electric behavior and a recursive function is deduced for the online identification of the OCV, which is implemented by a recursive least squares (RLS) algorithm with an optimal forgetting factor. The models with different RC networks are evaluated based on the terminal voltage comparisons between the model-based simulation and the experiment. Then the OCV-SOC lookup table is built based on the experimental data performed by a linear interpolation of the battery voltages at the same SOC during two consecutive discharge and charge cycles. Finally a verifying experiment is carried out based on nine Urban Dynamometer Driving Schedules. It indicates that the proposed method can ensure an acceptable accuracy of SOC estimation for online application with a maximum error being less than 5.0%. -- Highlights: ► An equivalent circuit model with n RC networks is built for lithium-ion batteries. ► A recursive function is deduced for the online estimation of the model parameters like OCV and RO. ► The relationship between SOC and OCV is built with a linear interpolation method by experiments. ► The experiments show the online model-based SOC estimation is reasonable with enough accuracy.

  1. 电动汽车用锂电池均衡充电技术研究%Research of efficient operation management techniques of lithium battery for electric vehicle

    Institute of Scientific and Technical Information of China (English)

    闫磊; 欧阳名三

    2015-01-01

    锂电池管理技术是电动汽车发展中存在的难题。在电动汽车使用过程中,锂电池组没有得到有效管理,导致汽车续驶里程短以及使用成本激增。以通过磷酸铁锂电池为研究对象,对电动汽车用锂电池高效运行管理进行设计研究,提出了电感主动均衡控制策略,以减少锂电池主动均衡时间,提高电动汽车用锂电池使用效率。%Lithium battery management technology is a problem existing in the development of electric vehicles. In the process of using electric vehicles, failing to manage lithium-ion battery effectively results in limited driving distance and soaring use cost. This paper determined the lithium iron phosphate batteries as the research object, the management of electric vehicle with lithium-ion batteries to work effectively in design research, inductive active equalization control strategy was proposed, in order to reduce the lithium battery active equilibrium time,Increasing the service efficiency of the electric car with lithium batteries.

  2. Research of efficient operation management techniques of lithium battery for electric vehicle%电动汽车用锂电池均衡充电技术研究

    Institute of Scientific and Technical Information of China (English)

    闫磊; 欧阳名三

    2015-01-01

    锂电池管理技术是电动汽车发展中存在的难题。在电动汽车使用过程中,锂电池组没有得到有效管理,导致汽车续驶里程短以及使用成本激增。以通过磷酸铁锂电池为研究对象,对电动汽车用锂电池高效运行管理进行设计研究,提出了电感主动均衡控制策略,以减少锂电池主动均衡时间,提高电动汽车用锂电池使用效率。%Lithium battery management technology is a problem existing in the development of electric vehicles. In the process of using electric vehicles, failing to manage lithium-ion battery effectively results in limited driving distance and soaring use cost. This paper determined the lithium iron phosphate batteries as the research object, the management of electric vehicle with lithium-ion batteries to work effectively in design research, inductive active equalization control strategy was proposed, in order to reduce the lithium battery active equilibrium time,Increasing the service efficiency of the electric car with lithium batteries.

  3. Impact of the Air-Conditioning System on the Power Consumption of an Electric Vehicle Powered by Lithium-Ion Battery

    Directory of Open Access Journals (Sweden)

    Brahim Mebarki

    2013-01-01

    Full Text Available The car occupies the daily universe of our society; however, noise pollution, global warming gas emissions, and increased fuel consumption are constantly increasing. The electric vehicle is one of the recommended solutions by the raison of its zero emission. Heating and air-conditioning (HVAC system is a part of the power system of the vehicle when the purpose is to provide complete thermal comfort for its occupants, however it requires far more energy than any other car accessory. Electric vehicles have a low-energy storage capacity, and HVAC may consume a substantial amount of the total energy stored, considerably reducing the vehicle range, which is one of the most important parameters for EV acceptability. The basic goal of this paper is to simulate the air-conditioning system impact on the power energy source of an electric vehicle powered by a lithium-ion battery.

  4. Modeling the Performance and Cost of Lithium-Ion Batteries for Electric-Drive Vehicles - SECOND EDITION

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Paul A. [Argonne National Lab. (ANL), Argonne, IL (United States); Gallagher, Kevin G. [Argonne National Lab. (ANL), Argonne, IL (United States); Bloom, Ira D. [Argonne National Lab. (ANL), Argonne, IL (United States); Dees, Dennis W. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2012-01-01

    This report details the Battery Performance and Cost model (BatPaC) developed at Argonne National Laboratory for lithium-ion battery packs used in automotive transportation. The model designs the battery for a specified power, energy, and type of vehicle battery. The cost of the designed battery is then calculated by accounting for every step in the lithium-ion battery manufacturing process. The assumed annual production level directly affects each process step. The total cost to the original equipment manufacturer calculated by the model includes the materials, manufacturing, and warranty costs for a battery produced in the year 2020 (in 2010 US$). At the time this report is written, this calculation is the only publicly available model that performs a bottom-up lithium-ion battery design and cost calculation. Both the model and the report have been publicly peer-reviewed by battery experts assembled by the U.S. Environmental Protection Agency. This report and accompanying model include changes made in response to the comments received during the peer-review. The purpose of the report is to document the equations and assumptions from which the model has been created. A user of the model will be able to recreate the calculations and perhaps more importantly, understand the driving forces for the results. Instructions for use and an illustration of model results are also presented. Almost every variable in the calculation may be changed by the user to represent a system different from the default values pre-entered into the program. The distinct advantage of using a bottom-up cost and design model is that the entire power-to-energy space may be traversed to examine the correlation between performance and cost. The BatPaC model accounts for the physical limitations of the electrochemical processes within the battery. Thus, unrealistic designs are penalized in energy density and cost, unlike cost models based on linear extrapolations. Additionally, the consequences on

  5. System for electric power generation with photovoltaic solar modules for charging the batteries of an electric wheelchair; Sistema de geracao de energia eletrica com modulos solares fotovoltaicos para o carregamento de baterias de uma cadeira de rodas eletrica

    Energy Technology Data Exchange (ETDEWEB)

    Mesquita, Rafael Pimenta; Souza, Teofilo Miguel de [Universidade Estadual Paulista (UNESP), Guaratinguta, SP (Brazil). Fac. de Engenharia. Dept. de Engenharia Eletrica], Emails: pimentamesquita@gmail.com, teofilo@feg.unesp.br

    2006-07-01

    Renewable energy is all kind of energy produced from a natural source that not diminish because its utilization is 'renewable'. More and more renewable energy resources are used, because they offer multiple advantages such as the energy output facility in small scale and because they are entirely compatible with the environment. The renewable energy used in this project is the photovoltaic solar energy, obtained by the direct conversion of the solar energy in electric energy through the use of solar cells, that can be of several kinds, being the most common of silicon. The main advantage of photovoltaic system is the generation of clean electric energy, or either, generates energy without emitting pollutant and without destroying the environment, moreover is an inexhaustible source of energy. The main disadvantage is, nowadays, the high cost and its low efficiency, so to continue developing it is necessary establish capable mechanisms to make it possible. The search of these mechanisms of incentive becomes-itself a lot important, because the renewable energy and not conventional do not produce a financial return to the investor properly said, but brings lots of benefits to the community, the society and to the environment. This project has the purpose of create an electric energy generation system through solar photovoltaic modules to carry batteries of a motorized wheelchair. An electric wheelchair is moved by electric motors of direct current that are feed by batteries, permitting a medium autonomy of 10 km by load. The batteries are recharged by a battery supplier. This operation should be carried out daily in a space of 6 to 8 hours. According to the Demographic Census realized in 2000 carried out by the IBGE, Brazil has around 1.416.060 physical deficient, which 861.196 are men and 554.864 are women. From a request of a user of electric wheelchair the idea of this project was shown up. The user complained that he stayed a long time carrying his seat

  6. 基于单片机的纯电动汽车电池管理系统设计%Design of microcontroller-based battery management system for pure electric vehicle

    Institute of Scientific and Technical Information of China (English)

    辛喆; 葛元月; 薄伟; 张云龙; 李亚平; 杨建为

    2014-01-01

    Energy conservation and environmental protection have become new targets of the development of the automobile industry. A new generation of electric vehicles have gotten a great development, which can diversify transport configuration with its zero-emission, low noise, etc., and attract extensive attentions worldwide. However, the battery problem of energy storage and application technology remains to restrict the development of electric vehicles. How to extend battery life and improve battery energy efficiency and operational reliability are problems that must be addressed for the electric vehicle energy management system. Battery management system is one of the key technologies related to electric vehicles and plays an important role in practice and commercialization, so the technology research of battery management system has a great significance. In all secondary batteries, the lithium batteries have the highest energy density and power density ratio, and became the most widely used electric vehicle batteries. Because of the inherent characteristics of lithium battery materials, overcharge, over-discharge, and over-temperature, battery pack performance will rapidly decay and eventually cause the battery pack failure. Therefore, the battery management system for lithium batteries plays an important role in extending the battery life cycle and maintaining safe operation of electric vehicles. This paper presents a kind of battery management system with a Freescale microcontroller core. It can provide accurate measurement of the battery cell voltage, total battery voltage, battery temperature, ambient temperature, current, and other information. The battery management system can also provide data to support the analysis of battery performance. In addition, the hardware circuit of the system has the functions of battery over-voltage/under-voltage protection and energy balance, etc., and the single cell can be monitored and implement the necessary protection. A PC

  7. Batteries: Overview of Battery Cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Doeff, Marca M

    2010-07-12

    hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs), and electric vehicles (EVs); a market predicted to be potentially ten times greater than that of consumer electronics. In fact, only Liion batteries can meet the requirements for PHEVs as set by the U.S. Advanced Battery Consortium (USABC), although they still fall slightly short of EV goals. In the case of Li-ion batteries, the trade-off between power and energy shown in Figure 1 is a function both of device design and the electrode materials that are used. Thus, a high power battery (e.g., one intended for an HEV) will not necessarily contain the same electrode materials as one designed for high energy (i.e., for an EV). As is shown in Figure 1, power translates into acceleration, and energy into range, or miles traveled, for vehicular uses. Furthermore, performance, cost, and abuse-tolerance requirements for traction batteries differ considerably from those for consumer electronics batteries. Vehicular applications are particularly sensitive to cost; currently, Li-ion batteries are priced at about $1000/kWh, whereas the USABC goal is $150/kWh. The three most expensive components of a Li-ion battery, no matter what the configuration, are the cathode, the separator, and the electrolyte. Reduction of cost has been one of the primary driving forces for the investigation of new cathode materials to replace expensive LiCoO{sub 2}, particularly for vehicular applications. Another extremely important factor is safety under abuse conditions such as overcharge. This is particularly relevant for the large battery packs intended for vehicular uses, which are designed with multiple cells wired in series arrays. Premature failure of one cell in a string may cause others to go into overcharge during passage of current. These considerations have led to the development of several different types of cathode materials, as will be covered in the next section. Because there is not yet one ideal material that can

  8. Batteries: Overview of Battery Cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Doeff, Marca M

    2010-07-12

    hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs), and electric vehicles (EVs); a market predicted to be potentially ten times greater than that of consumer electronics. In fact, only Liion batteries can meet the requirements for PHEVs as set by the U.S. Advanced Battery Consortium (USABC), although they still fall slightly short of EV goals. In the case of Li-ion batteries, the trade-off between power and energy shown in Figure 1 is a function both of device design and the electrode materials that are used. Thus, a high power battery (e.g., one intended for an HEV) will not necessarily contain the same electrode materials as one designed for high energy (i.e., for an EV). As is shown in Figure 1, power translates into acceleration, and energy into range, or miles traveled, for vehicular uses. Furthermore, performance, cost, and abuse-tolerance requirements for traction batteries differ considerably from those for consumer electronics batteries. Vehicular applications are particularly sensitive to cost; currently, Li-ion batteries are priced at about $1000/kWh, whereas the USABC goal is $150/kWh. The three most expensive components of a Li-ion battery, no matter what the configuration, are the cathode, the separator, and the electrolyte. Reduction of cost has been one of the primary driving forces for the investigation of new cathode materials to replace expensive LiCoO{sub 2}, particularly for vehicular applications. Another extremely important factor is safety under abuse conditions such as overcharge. This is particularly relevant for the large battery packs intended for vehicular uses, which are designed with multiple cells wired in series arrays. Premature failure of one cell in a string may cause others to go into overcharge during passage of current. These considerations have led to the development of several different types of cathode materials, as will be covered in the next section. Because there is not yet one ideal material that can

  9. 一种电动车用锂电池剩余容量检测系统%A SOC detecting system for electric bicycle battery

    Institute of Scientific and Technical Information of China (English)

    赵庆河

    2012-01-01

    针对电动车应用中的需求,提出了一种电动车用锂电池剩余容量(SOC)检测的方法,并设计了一套SOC检测系统.该系统以AVR单片机为控制及计算核心、以ACS712为电流采集器,采用线性光耦隔离模拟电压信号,集合充放电电流对时间的积分和BP神经网络估算两种方法来测量电池SOC值.该系统具有成本低、安全可靠、计算准确等特点,适合在电动车上推广使用.%For electric bicycle application demand, a method of electric bicycle lithium battery state of charge (SOC) detection is proposed, and a SOC detection system is designed. The system is based on AVR MCU as the control and calculation core, used ACS712 as current collector. It uses a linearopto -isolator to insulate analog voltage signal. It measures SOC of the battery integrating two methods which are current integration to the time and BP neural network estimation. The system has the advantages of low cost, safe and reliable, accurate calculation and other characteristics. It is suitable for use in electric vehicles.

  10. Electrochemical accumulators batteries; Accumulateurs electrochimiques batteries

    Energy Technology Data Exchange (ETDEWEB)

    Ansart, F.; Castillo, S.; Laberty- Robert, C.; Pellizon-Birelli, M. [Universite Paul Sabatier, Lab. de Chimie des Materiaux Inorganiques et Energetiques, CIRIMAT, UMR CNRS 5085, 31 - Toulouse (France)] [and others

    2000-07-01

    It is necessary to storage the electric power in batteries to join the production and the utilization. In this domain progresses are done every days in the technics and also in the available materials. These technical days present the state of the art in this domain. Many papers were presented during these two days giving the research programs and recent results on the following subjects: the lithium batteries, the electrolytes performances and behaviour, lead accumulators, economic analysis of the electrochemical storage market, the batteries applied to the transportation sector and the telephones. (A.L.B.)

  11. 飞轮电池在混合动力电动汽车中的应用分析%The Research of Flywheel Battery's Application in Electric Vehicles

    Institute of Scientific and Technical Information of China (English)

    游文娟; 王归新; 刘兴文

    2013-01-01

    For the battery's high charge and discharge current in electric vehicles, This paper focuses on the application of flywheel batteries using in hybrid electric vehicles.The paper analyzes Flywheel batteries and accumulators composite power system's simulation studies, using a digital proportional-integral-derivative (PID) algorithm to control strategy flywheel battery fast charge control. It Helps to improve the driving source for charging and discharging of the battery performance and prolong the life of the driving force for the battery ,the battery can be protected.%针对采用混合动力电动汽车蓄电池的大电流充放电问题,本文着重研究了飞轮电池在混合动力电动汽车上的应用。对飞轮电池和蓄电池的混合能源系统进行了分析研究,并采用一种数字比例-积分-微分(PID)控制算法建立了飞轮电池充放电的控制,对飞轮电池进行快速充放电控制,结果表明有助于提高原动力电池的充放电性能以及延长原动力蓄电池的使用寿命,对蓄电池进行保护。

  12. Lithium ion battery production

    International Nuclear Information System (INIS)

    Highlights: ► Sustainable battery manufacturing focus on more efficient methods and recycling. ► Temperature control and battery management system increase battery lifetime. ► Focus on increasing battery performance at low- and high temperatures. ► Production capacity of 100 MWh equals the need of 3000 full-electric cars. - Abstract: Recently, new materials and chemistry for lithium ion batteries have been developed. There is a great emphasis on electrification in the transport sector replacing part of motor powered engines with battery powered applications. There are plans both to increase energy efficiency and to reduce the overall need for consumption of non-renewable liquid fuels. Even more significant applications are dependent on energy storage. Materials needed for battery applications require specially made high quality products. Diminishing amounts of easily minable metal ores increase the consumption of separation and purification energy and chemicals. The metals are likely to be increasingly difficult to process. Iron, manganese, lead, zinc, lithium, aluminium, and nickel are still relatively abundant but many metals like cobalt and rare earths are becoming limited resources more rapidly. The global capacity of industrial-scale production of larger lithium ion battery cells may become a limiting factor in the near future if plans for even partial electrification of vehicles or energy storage visions are realized. The energy capacity needed is huge and one has to be reminded that in terms of cars for example production of 100 MWh equals the need of 3000 full-electric cars. Consequently annual production capacity of 106 cars requires 100 factories each with a 300 MWh capacity. Present day lithium ion batteries have limitations but significant improvements have been achieved recently . The main challenges of lithium ion batteries are related to material deterioration, operating temperatures, energy and power output, and lifetime. Increased lifetime

  13. Design of battery centralized management for electric vehicle%车载电池集中管理方案设计

    Institute of Scientific and Technical Information of China (English)

    任发; 刘和平; 周颖; 陈琼良

    2011-01-01

    An electric vehicle (EV) power batteries management system was designed, which could measure the voltage and temperatures of multiple batteries. The major hardware schematic was given. The circuit's design idea of voltage measurement unit was described in detail by using multiple routes of linear optocoupler HCNR201. The Saber circuit model simulation and software algorithm diagram were given.The experimental results prove the feasibility, accuracy and low cost of the battery centralized management system.%设计了一种车载动力电池组的管理系统,可以使用一个微控制器集中采集多路电池的电压和温度,给出了硬件方案.详细的介绍了通过多路线性光耦器件HCNR201,实现电压检测的设计思路,并给出了Saber仿真验证电路模型和软件算法框图.实验结果验证了电池集中管理方案的可行性、高精度和低成本性.

  14. A High-Gain Three-Port Power Converter with Fuel Cell, Battery Sources and Stacked Output for Hybrid Electric Vehicles and DC-Microgrids

    Directory of Open Access Journals (Sweden)

    Ching-Ming Lai

    2016-03-01

    Full Text Available This paper proposes a novel high-gain three-port power converter with fuel cell (FC, battery sources and stacked output for a hybrid electric vehicle (HEV connected to a dc-microgrid. In the proposed power converter, the load power can be flexibly distributed between the input sources. Moreover, the charging or discharging of the battery storage device can be controlled effectively using the FC source. The proposed converter has several outputs in series to achieve a high-voltage output, which makes it suitable for interfacing with the HEV and dc-microgrid. On the basis of the charging and discharging states of the battery storage device, two power operation modes are defined. The proposed power converter comprises only one boost inductor integrated with a flyback transformer; the boost and flyback circuit output terminals are stacked to increase the output voltage gain and reduce the voltage stress on the power devices. This paper presents the circuit configuration, operating principle, and steady-state analysis of the proposed converter, and experiments conducted on a laboratory prototype are presented to verify its effectiveness.

  15. A field operational test on valve-regulated lead-acid absorbent-glass-mat batteries in micro-hybrid electric vehicles. Part I. Results based on kernel density estimation

    Science.gov (United States)

    Schaeck, S.; Karspeck, T.; Ott, C.; Weckler, M.; Stoermer, A. O.

    2011-03-01

    In March 2007 the BMW Group has launched the micro-hybrid functions brake energy regeneration (BER) and automatic start and stop function (ASSF). Valve-regulated lead-acid (VRLA) batteries in absorbent glass mat (AGM) technology are applied in vehicles with micro-hybrid power system (MHPS). In both part I and part II of this publication vehicles with MHPS and AGM batteries are subject to a field operational test (FOT). Test vehicles with conventional power system (CPS) and flooded batteries were used as a reference. In the FOT sample batteries were mounted several times and electrically tested in the laboratory intermediately. Vehicle- and battery-related diagnosis data were read out for each test run and were matched with laboratory data in a data base. The FOT data were analyzed by the use of two-dimensional, nonparametric kernel estimation for clear data presentation. The data show that capacity loss in the MHPS is comparable to the CPS. However, the influence of mileage performance, which cannot be separated, suggests that battery stress is enhanced in the MHPS although a battery refresh function is applied. Anyway, the FOT demonstrates the unsuitability of flooded batteries for the MHPS because of high early capacity loss due to acid stratification and because of vanishing cranking performance due to increasing internal resistance. Furthermore, the lack of dynamic charge acceptance for high energy regeneration efficiency is illustrated. Under the presented FOT conditions charge acceptance of lead-acid (LA) batteries decreases to less than one third for about half of the sample batteries compared to new battery condition. In part II of this publication FOT data are presented by multiple regression analysis (Schaeck et al., submitted for publication [1]).

  16. High-performance batteries for electric-vehicle propulsion and stationary energy storage. Progress report, October 1978-September 1979. [40 kWh, Li-Al and Li-Si anodes

    Energy Technology Data Exchange (ETDEWEB)

    Barney, D. L.; Steunenberg, R. K.; Chilenskas, A. A.; Gay, E. C.; Battles, J. E.; Hornstra, F.; Miller, W. E.; Vissers, D. R.; Roche, M. F.; Shimotake, H.; Hudson, R.; Askew, B. A.; Sudar, S.

    1980-03-01

    The research, development, and management activities of the programs at Argonne National Laboratory (ANL) and at contractors' laboratories on high-temperature batteries during the period October 1978 to September 1979 are reported. These batteries are being developed for electric-vehicle propulsion and for stationary energy-storage applications. The present cells, which operate at 400 to 500/sup 0/C, are of a vertically oriented, prismatic design with one or more inner positive electrodes of FeS or FeS/sub 2/, facing negative electrodes of lithium-aluminum or lithium-silicon alloy, and molten LiCl-KC1 electrolyte. During this reporting period, cell and battery development work has continued at ANL and contractors' laboratories. A 40 kWh electric-vehicle battery (designated Mark IA) was fabricated and delivered to ANL for testing. During the initial heat-up, one of the two modules failed due to a short circuit. A failure analysis was conducted, and the Mark IA program completed. Development work on the next electric-vehicle battery (Mark II) was initiated at Eagle-Picher Industries, Inc. and Gould, Inc. Work on stationary energy-storage batteries during this period has consisted primarily of conceptual design studies. 107 figures, 67 tables.

  17. Investigation of lead dendrite growth in the formation of valve-regulated lead-acid batteries for electric bicycle applications

    Science.gov (United States)

    Zeng, Yanzhen; Hu, Jingcheng; Ye, Wenmei; Zhao, Wenchao; Zhou, Gang; Guo, Yonglang

    2015-07-01

    The battery temperature, H2SO4 distribution, Pb2+ ion concentration and composition of the plates during the plate soaking of the 12 V 12 Ah valve-regulated lead-acid (VRLA) battery are studied. A simulated cell composed by two pure Pb plates and the absorptive glass mat (AGM) separator is used to investigate the growth of the lead dendrite in the separator, which is verified by analyzing the faulty batteries after the formation and the failure batteries after the usage. It is found that the H2SO4 is exhausted very quickly after filling and the separator near the plates can become neutral during soaking. Low acidity, high temperature and small PbSO4 particle size will increase the Pb2+ ion concentration. Higher Pb2+ ion concentration makes more PbSO4 tend to deposit on the coarse glass fibers, develop along them and even enwrap the entire fiber. And the fine PbSO4 crystals are continually transformed into large PbSO4 crystals via dissolution-deposition. In the subsequent charge, these PbSO4 crystals will be reduced to the club-shaped lead dendrites and may lead to short circuit of the battery.

  18. 纯电动车电池组散热必要性的初步分析%A Preliminary Analysis on the Necessity of Battery Pack Cooling for Pure Electric Vehicles

    Institute of Scientific and Technical Information of China (English)

    梁金华; 李建秋; 卢兰光; 欧阳明高

    2012-01-01

    针对最近市场上出现的一些电池组不配备散热装置的纯电动车,对一款正在使用的、不带散热装置的纯电动车用磷酸铁锂电池组,通过试验测试和模型仿真进行不加散热的可行性分析.结果表明,刚使用的纯电动车电池组内阻小,热容量大,温升有限,在保证电池初始温度合适的情况下(尤其当采用换电模式),电池组可以不加散热装置,但是随着电池的老化,电池内阻大幅增加,导致温升增大,此时电池组应考虑散热.%Aiming at some models of electric vehicles without battery pack cooling device recently appeared on vehicle market, a feasibility analysis on electric vehicles without battery pack cooling device is conducted in this paper by both measurement test and model simulation on an EV with lithium iron phosphate battery but no cooling device currently in operation. The analysis leads to a conclusion that at the early operation stage of EV, due to small internal resistance and large heat capacity there is not much temperature rise in battery pack so if suitable initial temperature is assured (in particular with battery pack exchange mode) the battery pack can work without cooling device; However with the aging of battery, the internal resistance of battery greatly increases resulting in significant temperature rise, the heat dissipation of battery pack should be considered.

  19. Molten Air -- A new, highest energy class of rechargeable batteries

    OpenAIRE

    Licht, Stuart

    2013-01-01

    This study introduces the principles of a new class of batteries, rechargeable molten air batteries, and several battery chemistry examples are demonstrated. The new battery class uses a molten electrolyte, are quasi reversible, and have amongst the highest intrinsic battery electric energy storage capacities. Three examples of the new batteries are demonstrated. These are the iron, carbon and VB2 molten air batteries with respective intrinsic volumetric energy capacities of 10,000, 19,000 an...

  20. A Study of University Students' Understanding of Simple Electric Circuits. Part 2: Batteries, Ohm's Law, Power Dissipated, Resistors in Parallel.

    Science.gov (United States)

    Picciarelli, V.; And Others

    1991-01-01

    Results of a systematic investigation into university students' (n=236) misunderstandings of d.c. simple circuit operations are reported. These results provide evidence of various misconceptions present before and after teaching the following topics: a battery as a source of constant current; the functional relation expressed by Ohm's law; power…

  1. Electro-chemical batteries for guided missiles

    Directory of Open Access Journals (Sweden)

    H. S. Jaggi

    1966-05-01

    Full Text Available Electro-chemical batteries owing to their simplicity and ease of stowage form one of the sources of electrical power inside a missile. However, all batteries are not suited for this application. This article describes the special features required of a missile borne battery pack and discusses the characteristics of various types of batteries available today in the world. Conclusions have been drawn as to the most suitable types of batteries for missile applications.

  2. 混合电动汽车电池管理系统设计%Design of battery management system for hybrid electrical cars

    Institute of Scientific and Technical Information of China (English)

    宋雪桦; 吴和生; 刘锦娟; 孙金虎; 薛小莉; 张育华

    2011-01-01

    The existed battery management system is relatively weak in the battery real-time monitoring. The real work of the battery status, fault is difficult to monitor.This paper presents a battery management system (BMS) for hy-brid\\electrical cars based on MC9S12XEP100, including hardware architecture and software development, and also analyses the principles and characteristics of battery management system. The upper computer and lower MCU software were designed, with the realization of SOC Algorithm by applications of AH metering and Kalman Filtering. Optimizing SOC calculate. Meeting the requirements of the calculation error of SOC 5%, and the end result error was 3.3%. The problem of data loss due to hardware power-down was resolved by designing calculations, with implementing the storage of data on computer. The results of simulation and tests show that the development of this system meets the design objectives.%目前已存在的电池管理系统相对薄弱,对电池实时工作状态和一些故障很难监控.设计了适用混合电动汽车上动态均衡式的电池管理系统(BMS).硬件系统采用MC9S12XEP100微控制器(MCU),通过分析电池管理系统的原理和特点,分别进行了上、下位机软件的设计,实现了安时法和Kalman两种剩余电量SOC算法的交互应用,优化了SOC估算,满足了系统估算5%以内的误差要求,实验最终结果误差为3.3%.同时解决了系统硬件掉电问题,实现上位机直接对数据的显示.测试实验表明系统达到了预期的目标.

  3. 纯电动轿车用锂离子电池系统技术研究%Pure Electric Cars Using Lithium-ion Battery System Technology Research

    Institute of Scientific and Technical Information of China (English)

    王若飞

    2015-01-01

    以某款纯电动轿车为研究对象,研究了电池包与整车的匹配集成及电池系统内部布置集成、设计了电池系统的热管理控制策略、开发了电池系统安全技术,并利用CFD对电池系统温升进行了分析设计,研究结果表明,电池系统本部布置合理,电池系统安全性高,系统冷却及控制系统合理。%In a pure electric cars as the research object, the research of battery pack and vehicle matching integration, integration and battery system interior layout design the battery thermal management of system control strategy, developed a battery system security technology, and by using CFD analyses the temperature rise of the battery system design, the results show that the battery system based layout reasonable, battery system has high security, cooling system and control system is reasonable.

  4. Membranes for Redox Flow Battery Applications

    OpenAIRE

    Maria Skyllas-Kazacos; Aishwarya Parasuraman; Tuti Mariana Lim; Suminto Winardi; Helen Prifti

    2012-01-01

    The need for large scale energy storage has become a priority to integrate renewable energy sources into the electricity grid. Redox flow batteries are considered the best option to store electricity from medium to large scale applications. However, the current high cost of redox flow batteries impedes the wide spread adoption of this technology. The membrane is a critical component of redox flow batteries as it determines the performance as well as the economic viability of the batteries. Th...

  5. Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

    OpenAIRE

    Nielsen, L.H.; Jørgensen K., null

    2000-01-01

    The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore toillustrate the potential synergistic interplay between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberal...

  6. Charging operation with high energy efficiency for electric vehicle valve-regulated lead-acid battery system

    Energy Technology Data Exchange (ETDEWEB)

    Ikeya, Tomohiko; Mita, Yuichi; Ishihara, Kaoru [Central Research Inst. of Electric Power Industry (CRIEPI), Komae Res. Lab., Lithium Battery Project, Tokyo (Japan); Sawada, Nobuyuki [Hokkaido Electric Power Co., Sapporo (Japan); Takagi, Sakae; Murakami, Jun-ichi [Tohoku Electric Power Co. Inc., Sendai (Japan); Kobayashi, Kazuyuki [Tokyo Electric Power Co., Yokohama (Japan); Sakabe, Tetsuya [Chubu Electric Power Co., Nagoya (Japan); Kousaka, Eiichi [Hokuriku Electric Power Co., Toyama (Japan); Yoshioka, Haruki [The Kansai Electric Power Co., Osaka (Japan); Kato, Satoru [The Chugoku Electric Power Co., Hiroshima (Japan); Yamashita, Masanori [Shikoku Research Inst. Inc., Takamatsu (Japan); Narisoko, Hayato [The Okinawa Electric Power Co., Naha (Japan); Nishiyama, Kazuo [The Central Electric Power Council, Tokyo (Japan); Adachi, Kazuyuki [Kyushu Electric Power Co., Fukuoka (Japan)

    2000-12-01

    A new, high-energy-efficiency charging operation with as little amount of overcharge as possible is proposed to improve the energy efficiency and the cycle life for an EV valve-regulated lead-acid battery. Under this operation, the EV battery system is charged with 105% of amount of the preceding discharge five out of six times and once with 115% in order that it is fully charged. The cycle lives were estimated using a valve-regulated lead-acid battery system of 12 modules connected in series, by SFUDS79 pattern discharging and measurement of the amount of discharge every 50 cycles. Three-step constant current charging with 115% of amount of the preceding discharge required more than 5 h with the final charging step of more than 210 min, with coulomb efficiency of only 87% and energy efficiency of 74%. On the other hand, under the high-energy-efficiency charging operation, three-step charging with 105% shortens the final charging time to 132 min. It was completed in less than 4 h with coulomb and energy efficiency of 95% and 84%, respectively. This operation increased the energy efficiency from 74% to 83% on average in six charging, and extended the cycle life by about 30% to more than 400 cycles. Decreasing the amount of charge by as much as possible suppressed the corrosion of the grids in the positive plate and the heat evolution in batteries due to shortening of the final charging step. Although the high-energy-efficiency charging operation led to the accumulation of inactive PbSO{sub 4} at the upper part of the negative plate, possibly due to the decreasing amount of overcharge, this operation could prolong the cycle life. Full charging once every six times is though to be effective in suppressing degradation caused by the accumulation of inactive PbSO{sub 4} in the negative plate due to the shortage of charge. (orig.)

  7. Electric vehicles and Li-ion batteries%电动汽车与锂离子电池

    Institute of Scientific and Technical Information of China (English)

    黄学杰

    2015-01-01

    文章简要介绍了混合动力汽车、插电式混合动力汽车、纯电动汽车和锂离子动力电池及其关键材料。发展电动汽车可以大幅度降低人们对石油的依赖和改善城市空气质量。锂离子电池性能优越,为电动汽车的发展提供了支撑。近期,新一代锂离子动力电池正极材料即将走向应用,可使电动汽车里程增加一倍,材料选择和电池设计及制造工艺与电池储存能量、寿命、安全等密切相关,尊道而重德,可做出“好”电池。%This paper gives a general introduction on xEVs(HEV,PHEV and EV) and Li-ion batteries. Developing of xEVs will remarkably reduce the consumption of oils and improve the air quality in cities. Advanced Li-ion batteries supports the industrialization of xEVS. Cathode materials with high energy density, long cycling life and low cost is developing and the range per charge for EVs is expected to be doubled in few years. The energy, service life and safety of a bat-tery are very much dependent on its materials choice and cell design. "Good" battery can be ob-tained with good understanding and good intention.

  8. Research, development and demonstration of nickel-iron batteries for electric vehicle propulsion. Annual report for 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    Research progress in the development of Ni/Fe batteries (electrodes in particular) for the period is described. The negative plate demonstrated a reliable lifetime of almost 1000 cycles; 20 mm positive plates were proved feasible; prototype cells yielded output at about 50 Wh/kg and 100 Wh/liter; program goals of 20% greater than these figures appear feasible. 27 figures, 20 tables. (RWR)

  9. Research, development, and demonstration of nickel-iron batteries for electric vehicle propulsion. Annual report for 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    The FY 1980 program continued to involve full-size, prototype cell, module and battery fabrication and evaluation, aimed at advancing the technical capabilities of the nickel-iron battery, while simultaneously reducing its potential cost in materials and process areas. Improved Electroprecipitation Process (EPP) nickel electrodes of design thickness (2.5 mm) are now being prepared that display stable capacities of 23 to 25 Ah for the C/3 drain rate at 200+ test cycles. Iron electrodes of the composite-type are delivering 24 Ah at the target thickness (1.0 mm). Iron electrodes are displaying capacity stability for > 1000 test cycles in continuing 3 plate cell tests. Finished cells have delivered 57 to 61 Wh/kg at C/3, and have demonstrated cyclic stability to 500+ cycles at 80% depth of discharge profiles at Westinghouse. A 6-cell module that demonstrated 239 Ah, 1735 Wh, 48 Wh/kg at the C/3 drain rate has also been evaluated at the National Battery Test Laboratory, ANL. It operated for 327 test cycles, to a level of 161 Ah at the C/3 rate, before being removed from test. Reduction in nickel electrode swelling (and concurrent stack starvation), to improve cycling, continues to be an area of major effort to reach the final battery cycle life objectives. Pasted nickel electrodes continue to show promise for meeting the life objectives while, simultaneously, providing a low manufacturing cost. Refinements have occurred in the areas of cell hardware, module manifolding and cell interconnections. These improvements have been incorporated into the construction and testing of the cells and modules for this program. Temperature tests at 0/sup 0/C were performed on a 6-cell module and showed a decrease in capacity of only 25% in Ah and .29% in Wh as compared to 25/sup 0/C performance. Additional tests are planned to demonstrate performance at -15/sup 0/C and 40/sup 0/C.

  10. High-performance batteries for off-peak energy storage and electric-vehicle propulsion. Progress report, January--June 1975. [Li--Al/KCl--LiCl/Fe sulfide, 42 kWh

    Energy Technology Data Exchange (ETDEWEB)

    1976-03-01

    This report describes the research and management efforts, for the period January--June 1975, of Argonne National Laboratory's program on high-performance lithium/metal sulfide batteries. The batteries are being developed for two applications, off-peak energy storage in electric utility networks and electric-vehicle propulsion. The battery design for the two applications differ, particularly in cell configuration and electrode design, because of the differing performance requirements. The present cells are vertically oriented, prismatic cells with two negative electrodes of a solid lithium--aluminium alloy, a central positive electrode of iron sulfide (FeS/sub 2/ or FeS), and an electrolyte of LiCl--KCl eutectic (mp, 352/sup 0/C). The operating temperature of the cells is about 400--450/sup 0/C. Recent effort in the development of engineering-scale cells was focused on designing and fabricating vertically oriented, prismatic cells and on improving the lifetime capabilities of cells. Work on electrode development was directed toward the evaluation of the factors that influence the performance of the negative electrode and the development of new designs of vertical, prismatic iron sulfide electrodes. Materials studies included work on improving feedthroughs and separators, corrosion tests of candidate materials of construction, and postoperative examinations of cells. Cell chemistry studies included continuing investigations of cell reactions and the identification of advanced cell systems. Battery development work included the design of a battery for an electric automobile and the development of battery components. The transfer of Li--Al/FeS/sub x/ battery technology to industry is being implemented through contracts with industrial firms for the manufacture of components, electrodes, and cells.

  11. 基于PIC单片机和CAN总线的纯电动汽车电池管理系统设计%Design of Battery Management System for Electric Vehicles based on PIC and CAN

    Institute of Scientific and Technical Information of China (English)

    罗森侨; 彭忆强; 易威

    2013-01-01

    为使电动汽车电池组能够安全、高效地运行,设计了一套纯电动汽车电池管理系统,以满足电动车辆对动力电池的要求.该系统采用PIC单片机作为各个节点的控制器,利用CAN总线将所有节点互联,实现数据的实时高效通信.其硬件电路可以实现电池组总电压、电流和各个单体电池的电压以及温度的实时测量,然后将数据进行软件处理,通过带有初始SOC修正的安时积分方法和OCV-SOC曲线,实现了电池剩余电量的评估.%In order to make the electric car battery pack safe and efficient, a pure electric vehicle battery management system is designed to meet the requirements of an electric vehicle for power battery. PIC microcontroller is used for each node in the system and all nodes are based on CAN bus to complete the real-time and efficient communication. The designed hardware circuit of the battery management system can achieve real-time measurement of the battery pack voltage, current, and single battery voltage and temperature. The data will be processed by software with initial SOC amendment integral method and OCV-SOC curve to complete the assessment of the remaining battery charge.

  12. A Comparative Study Based on the Least Square Parameter Identification Method for State of Charge Estimation of a LiFePO4 Battery Pack Using Three Model-Based Algorithms for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Taimoor Zahid

    2016-09-01

    Full Text Available Battery energy storage management for electric vehicles (EV and hybrid EV is the most critical and enabling technology since the dawn of electric vehicle commercialization. A battery system is a complex electrochemical phenomenon whose performance degrades with age and the existence of varying material design. Moreover, it is very tedious and computationally very complex to monitor and control the internal state of a battery’s electrochemical systems. For Thevenin battery model we established a state-space model which had the advantage of simplicity and could be easily implemented and then applied the least square method to identify the battery model parameters. However, accurate state of charge (SoC estimation of a battery, which depends not only on the battery model but also on highly accurate and efficient algorithms, is considered one of the most vital and critical issue for the energy management and power distribution control of EV. In this paper three different estimation methods, i.e., extended Kalman filter (EKF, particle filter (PF and unscented Kalman Filter (UKF, are presented to estimate the SoC of LiFePO4 batteries for an electric vehicle. Battery’s experimental data, current and voltage, are analyzed to identify the Thevenin equivalent model parameters. Using different open circuit voltages the SoC is estimated and compared with respect to the estimation accuracy and initialization error recovery. The experimental results showed that these online SoC estimation methods in combination with different open circuit voltage-state of charge (OCV-SoC curves can effectively limit the error, thus guaranteeing the accuracy and robustness.

  13. 电动汽车锂离子电池低温加热方法研究%Method for Heating Low-Temperature Lithium Battery in Electric Vehicle

    Institute of Scientific and Technical Information of China (English)

    张承宁; 雷治国; 董玉刚

    2012-01-01

    为提高锂离子动力电池的低温充放电性能,以锰酸锂80A·h电池单体为研究对象,提出了宽线金属膜的加热方法,并对电池单体进行低温充放电实验,建立电池加热模型,采用等效电池加热实验验证模型的正确性,对233K低温环境下的电池单体进行加热和放电实验.实验结果表明,采用宽线金属膜加热法可显著提高电池的低温性能.%Under the condition of cold temperature, the charge-discharge performance of batteries in electric vehicles is dropped substantially due to the increase of viscosity of battery's electrolyte and the ascent of internal resistance. The method and development of heating battery system becomes a key technique to be solved. This research has developed a wide-line metal film method for heating batteries and performed low-temperature charging and discharging experiments on 80 A · h Li-ion battery cell. A model of heating battery was built and its correctness was verified by heating experiments with equivalent battery. Heating and discharging experiments of battery cell at -40 ℃ were implemented, and the results show that the discharge performance of heated battery cell is significantly improved.

  14. ZEBRA battery meets USABC goals

    Science.gov (United States)

    Dustmann, Cord-H.

    In 1990, the California Air Resources Board has established a mandate to introduce electric vehicles in order to improve air quality in Los Angeles and other capitals. The United States Advanced Battery Consortium has been formed by the big car companies, Electric Power Research Institute (EPRI) and the Department of Energy in order to establish the requirements on EV-batteries and to support battery development. The ZEBRA battery system is a candidate to power future electric vehicles. Not only because its energy density is three-fold that of lead acid batteries (50% more than NiMH) but also because of all the other EV requirements such as power density, no maintenance, summer and winter operation, safety, failure tolerance and low cost potential are fulfilled. The electrode material is plain salt and nickel in combination with a ceramic electrolyte. The cell voltage is 2.58 V and the capacity of a standard cell is 32 Ah. Some hundred cells are connected in series and parallel to form a battery with about 300 V OCV. The battery system including battery controller, main circuit-breaker and cooling system is engineered for vehicle integration and ready to be mounted in a vehicle [J. Gaub, A. van Zyl, Mercedes-Benz Electric Vehicles with ZEBRA Batteries, EVS-14, Orlando, FL, Dec. 1997]. The background of these features are described.

  15. International Space Station Lithium-Ion Battery

    Science.gov (United States)

    Dalton, Penni J.; Balcer, Sonia

    2016-01-01

    The International Space Station (ISS) Electric Power System (EPS) currently uses Nickel-Hydrogen (Ni-H2) batteries to store electrical energy. The batteries are charged during insolation and discharged during eclipse. The Ni-H2 batteries are designed to operate at a 35 depth of discharge (DOD) maximum during normal operation in a Low Earth Orbit. Since the oldest of the 48 Ni-H2 battery Orbital Replacement Units (ORUs) has been cycling since September 2006, these batteries are now approaching their end of useful life. In 2010, the ISS Program began the development of Lithium-Ion (Li-ion) batteries to replace the Ni-H2 batteries and concurrently funded a Li-ion cell life testing project. This paper will include an overview of the ISS Li-Ion battery system architecture and the progress of the Li-ion battery design and development.

  16. Thermal and lifetime battery model for the feasibility study of a lithium-ion battery system as a thermal storage in an electric-powered vehicle; Thermisches und Lebensdauerbatteriemodell fuer die Konzeptuntersuchung eines Lithium-Ionen Batteriesystems als Waermespeicher im Elektrofahrzeug

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Wei; Schaeper, Christoph; Ecker, Madeleine; Sauer, Dirk Uwe [RWTH Aachen Univ. (Germany). Inst. fuer Stromrichtertechnik und Elektrische Antriebe (ISEA); Fischer, Tim; Bohmann, Carl [Bosch Engineering GmbH, Abstadt (Germany); Hoerth, Leonhard [Technische Univ. Muenchen (Germany). Lehrstuhl fuer Thermodynamik

    2012-11-01

    The increasing electrification of passenger vehicles provides the opportunity to drive environmentally friendly and emission-free. However, the requirements increase in terms of air conditioning in particular heating the vehicle cabin. The low waste heat from power train and electrical energy storage system are not sufficient to meet the energy demand of the cabin. Without additional arrangements the heating demand for comfort and safety in the cabin is not covered and energy has to be removed from the electrical energy storage. This leads to an inevitable range reduction. As part of the BMBF-funded project ''e performance'' the concept of using a lithium-ion battery with its heat capacity as a thermal storage is examined. The energy storage system of the vehicle developed in the project consists of two independent battery packs, one of which can be charged with heat during the electric charging process via the power grid. While driving, the stored heat can be delivered to the passenger cabin by means of the coolant and refrigerant circuit. This article focuses on the thermal behavior of the battery pack in such an application and the possible impact on the battery aging. A thermal battery system model calculates the inhomogeneity of the temperature distribution within a single cell and across the whole battery pack, during thermal charging and discharging. This model can be implemented in the battery management system (BMS) in order to calculate the current average cell temperatures using the measured temperatures on the cell shell. The maximum temperature differences of cells and across the pack can also be determined. Based on these values and according to the safety and lifetime criteria of the lithium-ion battery, the BMS will inform the vehicle thermal manager how quickly the battery system can be thermally charged and discharged, and when these processes should to be terminated. It is also estimated how the lifetime of the implemented

  17. Lithium use in batteries

    Science.gov (United States)

    Goonan, Thomas G.

    2012-01-01

    Lithium has a number of uses but one of the most valuable is as a component of high energy-density rechargeable lithium-ion batteries. Because of concerns over carbon dioxide footprint and increasing hydrocarbon fuel cost (reduced supply), lithium may become even more important in large batteries for powering all-electric and hybrid vehicles. It would take 1.4 to 3.0 kilograms of lithium equivalent (7.5 to 16.0 kilograms of lithium carbonate) to support a 40-mile trip in an electric vehicle before requiring recharge. This could create a large demand for lithium. Estimates of future lithium demand vary, based on numerous variables. Some of those variables include the potential for recycling, widespread public acceptance of electric vehicles, or the possibility of incentives for converting to lithium-ion-powered engines. Increased electric usage could cause electricity prices to increase. Because of reduced demand, hydrocarbon fuel prices would likely decrease, making hydrocarbon fuel more desirable. In 2009, 13 percent of worldwide lithium reserves, expressed in terms of contained lithium, were reported to be within hard rock mineral deposits, and 87 percent, within brine deposits. Most of the lithium recovered from brine came from Chile, with smaller amounts from China, Argentina, and the United States. Chile also has lithium mineral reserves, as does Australia. Another source of lithium is from recycled batteries. When lithium-ion batteries begin to power vehicles, it is expected that battery recycling rates will increase because vehicle battery recycling systems can be used to produce new lithium-ion batteries.

  18. Long-term assessment of economic plug-in hybrid electric vehicle battery lifetime degradation management through near optimal fuel cell load sharing

    Science.gov (United States)

    Martel, François; Dubé, Yves; Kelouwani, Sousso; Jaguemont, Joris; Agbossou, Kodjo

    2016-06-01

    This work evaluates the performance of a plug-in hybrid electric vehicle (PHEV) energy management process that relies on the active management of the degradation of its energy carriers - in this scenario, a lithium-ion battery pack and a polymer electrolyte membrane fuel cell (PEMFC) - to produce a near economically-optimal vehicle operating profile over its entire useful lifetime. This solution is obtained through experimentally-supported PHEV models exploited by an optimal discrete dynamic programming (DDP) algorithm designed to efficiently process vehicle usage cycles over an extended timescale. Our results demonstrate the economic and component lifetime gains afforded by our strategy when compared with alternative rule-based PHEV energy management benchmarks.

  19. Cu0.02Ti0.94Nb2.04O7: An advanced anode material for lithium-ion batteries of electric vehicles

    Science.gov (United States)

    Yang, Chao; Lin, Chunfu; Lin, Shiwei; Chen, Yongjun; Li, Jianbao

    2016-10-01

    To explore advanced anode materials for lithium-ion batteries of electric vehicles, Cu2+/Nb5+ co-doped TiNb2O7 is studied. Cu0.02Ti0.94Nb2.04O7 is successfully fabricated using a facile solid-state reaction. X-ray diffraction analyses combined with Rietveld refinements demonstrate that the trace Cu2+/Nb5+ co-doping does not destroy the shear ReO3 crystal structure of TiNb2O7 but increases the lattice parameters and unit cell volume. Specific surface area tests and scanning electron microscopy images reveal a smaller average particle size in Cu0.02Ti0.94Nb2.04O7. Due to the increased unit cell volume and free 3d electrons in Cu2+ ions, the Li+-ion diffusion coefficient and electronic conductivity of Cu0.02Ti0.94Nb2.04O7 are respectively enhanced by 14.8 times and at least 220 times. Consequently, Cu0.02Ti0.94Nb2.04O7 exhibits advanced electrochemical properties in terms of specific capacity, rate capability and cyclic stability. At 0.1 C, it delivers a large first-cycle discharge/charge capacity of 346/315 mAh g-1. At 10 C, it still provides a large capacity of 182 mAh g-1 with tiny loss of only 1.2% over 1000 cycles. In sharp contrast, TiNb2O7 shows a small capacity of only 90 mAh g-1 and large loss of 59.8%. Therefore, Cu0.02Ti0.94Nb2.04O7 possesses great potential for the application in lithium-ion batteries for electric vehicles.

  20. 陕西省电动汽车动力电池产业发展技术路线研究%The Research onTechnicalRoute of Battery forElectric Vehicle in Shaanxi Province

    Institute of Scientific and Technical Information of China (English)

    贺伊琳; 苏楠; 鹿静; 王栋梁

    2016-01-01

    With the development of industrialization, there appears a significant increase in the number of cars, followed by environmental pollution and energy shortage, Electric car isenvironmentally friendlyand will not have pressure on oil, and then it have become a hot spot in today. The battery is the core technology of electric vehicles, the development of power battery directly affects the development of electric vehicles. Therefore, improving the technological level of battery power is important to promote the development of electric vehicle. Thispaper discusses the status of the development of battery powerat home and abroad and makes an compare of some types of batteries. Shanxi provincepower battery industry is introduced based on SWOT.Finally, studying the Shanxi Province technical route of electric vehicle battery development with its status, clearing development objectives, proposing key technology and exploring important spot,thiswill havegreat theoretical significance and guidance on future development of battery technology in Shanxi Province.%随着工业化进展,汽车数量大幅增加,随之而来的是环境污染和能源危机,电动汽车绿色环保,且不会对石油能源造成压力,已成为当今世界研究的热点。动力电池是电动汽车的核心技术之一,其发展直接影响电动汽车的性能,因此,提高动力电池的技术水平对促进电动汽车技术的进步具有重要意义。文章首先论述国内外动力电池的发展现状,对每种电池的性能进行比较,其次基于 SWOT 理论对目前陕西省动力电池产业进行分析,最后结合陕西省现状对该省电动汽车动力电池发展的技术路线进行研究,明确发展目标,提出关键技术与研发重点内容,对陕西省动力电池技术今后的发展具有重要理论意义与指导作用。