WorldWideScience

Sample records for bar code label

  1. Irradiation test of bar code label

    International Nuclear Information System (INIS)

    The irradiation test of bar code label tagged on radioactive waste container was done to determine the effect of radiation. Low and medium radioactive waste is that below total activity of 4,000Bq/g according to the Korean nuclear law. The irradiation amount to radiate bar code label tagged on radioactive waste container was calculated by MCNP-4b computer code. The nuclide such as Co-60 and Cs-137 was assumed to contribute 50 % of total activity. Real irradiation amount for bar code label was finally calculated by the dimensions of the container and the bar code label. The identification of post and the physical deflection of irradiated bar code label was tested by the bar code reader. The coated bar code label was suitable to use on low and medium radioactive waste container

  2. Monitoring the laser marking of a bar code label

    International Nuclear Information System (INIS)

    A bar code label which has been laser marked onto the end of a nuclear fuel tube is tested for unacceptable depth penetration of the heat affected zone. The average gray level value of the bar code label is compared with a predetermined standard. The label is optically sensed by a video camera and a set of discrete digital values representative of the bar code label is generated. The average digital value representative of the bar code label is calculated and compared to a predetermined standard level derived from measurements of acceptable laser marked tubes. (author)

  3. Animal house stock control based on bar-coded cage labels.

    Science.gov (United States)

    Wootton, R

    1985-10-01

    In an animal house serving the needs of a large research institute, a regular inventory of the animals in stock is a considerable help towards effective management of the facility. In particular, advising the licence-holders of what animals are being held in their name and reminding them of the costs involved is a valuable exercise. The introduction of a computerized system of stock control, based on bar-coded cage labels, is described. The system has proved economical to operate, accurate, and can be run by persons without computer expertise. PMID:4068665

  4. Bar code instrumentation for nuclear safeguards

    International Nuclear Information System (INIS)

    This paper presents a brief overview of the basic principles of bar codes and the equipment used to make and to read bar code labels, and a summary of some of the more important factors that need to be considered in integrating bar codes into an information system

  5. Blurring in bar code signals

    Science.gov (United States)

    Tang, Hong

    1997-10-01

    When a bar code symbol is passed over a scanner, it is struck across by a fast moving laser beam. The laser light is scattered by the bar code. The total scattered power is modulated by the reflectivity of the bars and spaces in the symbol. A fraction of the scattered light is collected and focused onto a photodetector that converts the light variation into an electronic signal. The electronic signal is then digitized for analysis by a computer. The scanning and detection process can be modeled by a convolution of the laser beam profile and the bar code reflectivity function. The switching between states in the digitized bar code signal, which represents transitions from a space to a bar or vice versa, is determined by a zero-crossing point in the second derivative of the analog signal. The laser profile acts like a smoothing function. It blurs the analog electronic signal. If the width of the laser profile is less than the minimum width of bars and spaces in the bar code reflectivity function, the transition point is not affected by the location of its neighboring edges. If the laser profile is wider than the minimum width in the bar code, the transition point can be shifted due to the locations of its neighboring edges. The behavior of the shift of transition is analyzed here for all cases in a UPC symbol. It is found that the amount of shift in the transition point is almost the same for several different cases within the depth of field of the scanner. The knowledge of the behavior of transition point shift can be used to accurately compensate printing errors in an over-printed bar code. The modulation transfer function (MTF) of bar code scanning is the Fourier transform of the marginal function of the scanning laser beam. The MTF through focus for a scanning system is presented. By using an aperture with central obscuration in the laser focusing system, the high frequency resolution of bar code scanning can be enhanced and the depth of field of the scanner can

  6. The application of bar coding technology at WIPP

    International Nuclear Information System (INIS)

    Bar coding at the Waste Isolation Pilot Plant (WIPP) can be used to track waste containers within the facility, control transuranic (TRU) waste inventory flow, and reduce manpower and error in recording package identification or control parameters. By choosing where and when to bar code, precise timelines or time-and-motion studies can be conducted to aid in streamlining waste handling throughput at WIPP. Additionally, the use of bar codes as waste container identification (ID) numbers increases the accuracy of recording the ID numbers by four orders of magnitude. The bar code label can also be utilized for other functions, such as shipping labels. Also, the bar code is integrated with the waste management data base such that the entire data base can be accessed on a computer using a bar code

  7. Modulation transfer function of bar code scanning

    Science.gov (United States)

    Tang, Hong; Milster, Tom D.

    1998-09-01

    Bar code scanners are ubiquitous in supermarkets. As a bar code is passed over a scanner, a laser beam scans across the bar code. The scattered light is modulated by the reflectivity of the bars and spaces of the bar code. The bar code scanning process can be described as a 1D convolution of the scanning laser profile and the bar code reflectivity function. The modulation transfer function (MTF) of bar code scanning is the Fourier transform of the marginal profile of the laser beam. The properties of the MTF of bar code scanning is similar to that of an incoherent imaging system. Measurements of the MTF of bar code scanning at one focus position are presented. The experimental results are then discussed.

  8. Bar-code automated waste tracking system

    International Nuclear Information System (INIS)

    The Bar-Code Automated Waste Tracking System was designed to be a site-Specific program with a general purpose application for transportability to other facilities. The system is user-friendly, totally automated, and incorporates the use of a drive-up window that is close to the areas dealing in container preparation, delivery, pickup, and disposal. The system features ''stop-and-go'' operation rather than a long, tedious, error-prone manual entry. The system is designed for automation but allows operators to concentrate on proper handling of waste while maintaining manual entry of data as a backup. A large wall plaque filled with bar-code labels is used to input specific details about any movement of waste

  9. Bar-code automated waste tracking system

    Energy Technology Data Exchange (ETDEWEB)

    Hull, T.E.

    1994-10-01

    The Bar-Code Automated Waste Tracking System was designed to be a site-Specific program with a general purpose application for transportability to other facilities. The system is user-friendly, totally automated, and incorporates the use of a drive-up window that is close to the areas dealing in container preparation, delivery, pickup, and disposal. The system features ``stop-and-go`` operation rather than a long, tedious, error-prone manual entry. The system is designed for automation but allows operators to concentrate on proper handling of waste while maintaining manual entry of data as a backup. A large wall plaque filled with bar-code labels is used to input specific details about any movement of waste.

  10. Bar code technology improves positive patient identification and transfusion safety.

    Science.gov (United States)

    Sandler, S G; Langeberg, A; Dohnalek, L

    2005-01-01

    As a result of human error, an estimated 1 in 12,000 blood transfusions is given to the wrong patient. The cause of nearly all of these errors is failure of hospital personnel to identify positively intended transfusion recipients, their blood samples for cross-matching, or their correct blood components. We describe our experience using a point-of-care bar code transfusion safety system that links patients' bar-coded wristbands, with bar-coded labels on blood sample tubes, blood component bags, and nurses' identification badges. The result was 100 % accuracy of matching patients, their blood samples, and components for transfusions. For verifying information before starting blood transfusions, nurses preferred bar code "double checks" to conventional visual "double checks" by a second nurse. Methods are needed to reinforce nurses' proficiency with technological approaches to transfusion safety, such as software-driven bar code scanning, in situations where transfusions are administered infrequently. PMID:16050151

  11. 19 CFR 142.45 - Use of bar code by entry filer.

    Science.gov (United States)

    2010-04-01

    ... filer and a product description below the bar code. (b) Multiple commodity processing. Multiple... variable allowed. The commodities should be listed on one invoice with C-4 Code labels for each...

  12. Effects of bar coding on a pharmacy stock replenishment system.

    Science.gov (United States)

    Chester, M I; Zilz, D A

    1989-07-01

    A bar-code stock ordering system installed in the ambulatory-care pharmacy and sterile products area of a hospital pharmacy was compared with a manual paper system to quantify overall time demands and determine the error rate associated with each system. The bar-code system was implemented in the ambulatory-care pharmacy in November 1987 and in the sterile products area in January 1988. It consists of a Trakker 9440 transaction manager with a digital scanner; labels are printed with a dot matrix printer. Electronic scanning of bar-code labels and entry of the amount required using the key-pad on the transaction manager replaced use of a preprinted form for ordering items. With the bar-code system, ordering information is transferred electronically via cable to the pharmacy inventory computer; with the manual system, this information was input by a stockroom technician. To compare the systems, the work of technicians in the ambulatory-care pharmacy and sterile products area was evaluated before and after implementation of the bar-code system. The time requirements for information gathering and data transfer were recorded by direct observation; the prevalence of errors under each system was determined by comparing unprocessed ordering information with the corresponding computer-generated "pick lists" (itemized lists including the amount of each product ordered). Time consumed in extra trips to the stockroom to replace out-of-stock items was self-reported. Significantly less time was required to order stock and transfer data to the pharmacy inventory computer with the bar-code system than with the manual system.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:2757044

  13. Measuring and test equipment control through bar-code technology

    International Nuclear Information System (INIS)

    Over the past several years, the use, tracking, and documentation of measuring and test equipment (M ampersand TE) has become a major issue. New regulations are forcing companies to develop new policies for providing use history, traceability, and accountability of M ampersand TE. This paper discusses how the Fast Flux Test Facility (FFTF), operated by Westinghouse Hanford Company and located at the Hanford site in Rich- land, Washington, overcame these obstacles by using a computerized system exercising bar-code technology. A data base was developed to identify M ampersand TE containing 33 separate fields, such as manufacturer, model, range, bar-code number, and other pertinent information. A bar-code label was attached to each piece of M ampersand TE. A second data base was created to identify the employee using the M ampersand TE. The fields contained pertinent user information such as name, location, and payroll number. Each employee's payroll number was bar coded and attached to the back of their identification badge. A computer program was developed to automate certain tasks previously performed and tracked by hand. Bar-code technology was combined with this computer program to control the input and distribution of information, eliminate common mistakes, electronically store information, and reduce the time required to check out the M ampersand TE for use

  14. Bar code application to nuclear material accountancy

    International Nuclear Information System (INIS)

    For the purpose of efficient implementation of IAEA safeguards inspection, operators ought to prepare the information which is related to the strata for flow verification in a timely manner, such as physical inventory listing and summary of the fuel bundles. Today the use of bar code technique in tracing of products related data or counting number of items has been more and more applied to many facets of industry. From these points of view, the Japan Nuclear Fuel Company (NF) has been developing JNF Total Bar Code System. Now JNF has established an on-line input system of the fuel bundle accountability data by use of the bar code system to quickly prepare the information necessary for the inspection. As the first step, JNF implemented this bar code system at the flow verification to prepare physical inventory summary and location map of the fuel bundles in the storage. This paper reports that as a result of this, NF confirmed that this bar code system made it possible to input easily and quickly nuclear material accountancy information, and therefore this system is utilized as an effective and efficient measure of timely preparation for the inspection

  15. Bar code usage in nuclear materials accountability

    International Nuclear Information System (INIS)

    The age old method of physically taking an inventory of materials by listing each item's identification number has lived beyond its usefulness. In this age of computerization, which offers the local grocery store a quick, sure, and easy means to inventory, it is time for nuclear materials facilities to automate accountability activities. The Oak Ridge Y-12 Plant began investigating the use of automated data collection devices in 1979. At that time, bar code and optical-character-recognition (OCR) systems were reviewed with the purpose of directly entering data into DYMCAS (Dynamic Special Nuclear Materials Control and Accountability System). Both of these systems appeared applicable; however, other automated devices already employed for production control made implementing the bar code and OCR seem improbable. However, the DYMCAS was placed on line for nuclear material accountability, a decision was made to consider the bar code for physical inventory listings. For the past several months a development program has been underway to use a bar code device to collect and input data to the DYMCAS on the uranium recovery operations. Programs have been completed and tested, and are being employed to ensure that data will be compatible and useful. Bar code implementation and expansion of its use for all nuclear material inventory activity in Y-12 is presented

  16. Bar code usage in nuclear materials accountability

    International Nuclear Information System (INIS)

    The Oak Ridge Y-12 Plant began investigating the use of automated data collection devices in 1979. At this time, bar code and optical-character-recognition (OCR) systems were reviewed with the purpose of directly entering data into DYMCAS (Dynamic Special Nuclear Materials Control and Accountability System). Both of these systems appeared applicable, however, other automated devices already employed for production control made implementing the bar code and OCR seem improbable. However, the DYMCAS was placed on line for nuclear material accountability, a decision was made to consider the bar code for physical inventory listings. For the past several months a development program has been underway to use a bar code device to collect and input data to the DYMCAS on the uranium recovery operations. Programs have been completed and tested, and are being employed to ensure that data will be compatible and useful. Bar code implementation and expansion of its use for all nuclear material inventory activity in Y-12 is presented

  17. BAR-MOM Code and Its Application

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    BAR-MOM [1,2] code to calculate the height of the fission barrier Bf, the energy of the ground state, the compound nucleus stability by limit with respect to fission, i.e., the angular momentum(the spin value) Lmax at which the fission barrier disappears, the three principal axis moments of inertia at saddle point for a certain nucleus with atomic number Z, atomic mass number and angular momentum L for 19BAR-MOM code to include the results for Z≥102[3] by using more recent parameterization of the Thomas Fermi fission

  18. Improving radiopharmaceutical supply chain safety by implementing bar code technology.

    Science.gov (United States)

    Matanza, David; Hallouard, François; Rioufol, Catherine; Fessi, Hatem; Fraysse, Marc

    2014-11-01

    The aim of this study was to describe and evaluate an approach for improving radiopharmaceutical supply chain safety by implementing bar code technology. We first evaluated the current situation of our radiopharmaceutical supply chain and, by means of the ALARM protocol, analysed two dispensing errors that occurred in our department. Thereafter, we implemented a bar code system to secure selected key stages of the radiopharmaceutical supply chain. Finally, we evaluated the cost of this implementation, from overtime, to overheads, to additional radiation exposure to workers. An analysis of the events that occurred revealed a lack of identification of prepared or dispensed drugs. Moreover, the evaluation of the current radiopharmaceutical supply chain showed that the dispensation and injection steps needed to be further secured. The bar code system was used to reinforce product identification at three selected key stages: at usable stock entry; at preparation-dispensation; and during administration, allowing to check conformity between the labelling of the delivered product (identity and activity) and the prescription. The extra time needed for all these steps had no impact on the number and successful conduct of examinations. The investment cost was reduced (2600 euros for new material and 30 euros a year for additional supplies) because of pre-existing computing equipment. With regard to the radiation exposure to workers there was an insignificant overexposure for hands with this new organization because of the labelling and scanning processes of radiolabelled preparation vials. Implementation of bar code technology is now an essential part of a global securing approach towards optimum patient management. PMID:25144560

  19. BAR-MOM code and its application

    International Nuclear Information System (INIS)

    BAR-MOM code for calculating the height of the fission barrier Bf , the energy of the ground state is presented; the compound nucleus stability by limit with respect to fission, i.e., the angular momentum (the spin value) Lmax at which the fission barrier disappears, the three principal axis moments of inertia at saddle point for a certain nucleus with atomic number Z, atomic mass number A and angular momentum L in units of ℎ for 19< Z<102, and the model used are introduced briefly. The generalized BAR-MOM code to include the results for Z ≥ 102 by using more recent parameterization of the Thomas Fermi fission barrier is also introduced briefly. We have learned the models used in Code BAR-MOM, and run it successfully and correctly for a certain nucleus with atomic mass number A, atomic number Z, and angular momentum L on PC by Fortran-90. The testing calculation values to check the implementation of the program show that the results of the present work are in good agreement with the original one

  20. Applications of bar code technology at nuclear power plants

    International Nuclear Information System (INIS)

    Bar code is an emerging technology that can eliminate handwritten and keyboard data-entry errors. With application-specific software, bar code technology can provide inventory control, reducing staff time and paperwork. This paper summarizes bar code technology, describes hardware commercially available, and reviews application software systems for use in nuclear power plants

  1. MOEM scan engine for bar code reading and factory automation

    Science.gov (United States)

    Motamedi, M. Edward; Park, Sangtae; Melendes, Robert; Wang, A.; Andrews, Angus P.; Garcia-Nunez, Dawn S.; Jinar, Dan; Richardson, Patti D.; Studer, J.; Chen, J. K.; DeNatale, Jeffrey F.; Moranski, Jeffrey A.

    1998-03-01

    Rockwell is in the state of technology transfer to manufacturing of a micro-opto-electro-mechanical scan engine with superior scanning performance for bar code reading and factory automation. The scan engine consists of three main components: actuator, mirrors, and control electronics. The first two components are fabricated on a silicon cantilever beam while the control electronics are presently hybrid. The actuator comprises of a bimorph layer covered with two metal layers. The mirror has a large area (several mm2) and it is micromachined with a surface flatness better than (lambda) /2. Actuator scan-angles greater than 22 degree(s) with high repeatability in performance are achieved. The scan engine was integrated with an existing Rockwell commercial bar code reader/decoder and successfully proven to read a two-character code 39 bar code. The system was capable of decoding the 13-mil label at 360 scans per second with a 100% successful read performance. Environmental testing of the device indicates that the scanner can operate at elevated temperatures up to 70 degree(s)C with minor fluctuations in frequency and scan angle. The scanner has also gone through a lifetime cycle test and it has survived more than 8 billion cycles during a period of 18 months. To increase the yield and the performance level of the device, theoretical study as well as dynamic simulation by finite elements modeling have been investigated and will be reported separately.

  2. System analysis of bar code laser scanner

    Science.gov (United States)

    Wang, Jianpu; Chen, Zhaofeng; Lu, Zukang

    1996-10-01

    This paper focuses on realizing the three important aspects of bar code scanner: generating a high quality scanning light beam, acquiring a fairly even distribution characteristic of light collection, achieving a low signal dynamic range over a large depth of field. To do this, we analyze the spatial distribution and propagation characteristics of scanning laser beam, the vignetting characteristic of optical collection system and their respective optimal design; propose a novel optical automatic gain control method to attain a constant collection over a large working depth.

  3. Application of bar codes to the automation of analytical sample data collection

    International Nuclear Information System (INIS)

    The Health Protection Department at the Savannah River Plant collects 500 urine samples per day for tritium analyses. Prior to automation, all sample information was compiled manually. Bar code technology was chosen for automating this program because it provides a more accurate, efficient, and inexpensive method for data entry. The system has three major functions: sample labeling is accomplished at remote bar code label stations composed of an Intermec 8220 (Intermec Corp.) interfaced to an IBM-PC, data collection is done on a central VAX 11/730 (Digital Equipment Corp.). Bar code readers are used to log-in samples to be analyzed on liquid scintillation counters. The VAX 11/730 processes the data and generates reports, data storage is on the VAX 11/730 and backed up on the plant's central computer. A brief description of several other bar code applications at the Savannah River Plant is also presented

  4. A bar-code reader for an alpha-beta automatic counting system - FAG

    International Nuclear Information System (INIS)

    A bar-code laser system for sample number reading was integrated into the FAG Alpha-Beta automatic counting system. The sample identification by means of an attached bar-code label enables unmistakable and reliable attribution of results to the counted sample. Installation of the bar-code reader system required several modifications: Mechanical changes in the automatic sample changer, design and production of new sample holders, modification of the sample planchettes, changes in the electronic system, update of the operating software of the system (authors)

  5. A simple and inexpensive bar-coding technique for denture identification

    Directory of Open Access Journals (Sweden)

    Sonali N Nalawade

    2011-01-01

    Full Text Available A number of commercial methods for identifying dentures are available. They can be either invasive or noninvasive techniques. The less sophisticated procedures include simple engraving with bur, and more sophisticated procedures use labels or chips. Bar coding system is a way of transferring data to the computer and huge data can be stored as a record. Bar coding can be easily incorporated during acrylization of the denture and thus could be used in individual identification.

  6. Management of manufacture and installation of plant pipings by bar code system

    International Nuclear Information System (INIS)

    As for the piping system of nuclear power plants, the number of parts is very large, and the mill sheet is attached to each part, therefore, it is necessary to manage them individually, and large man power is required. In order to resolve the delay of mechanization in the factory, bar code system was adopted on full scale. At the time of taking parts out from the store, bar code labels are stuck to all piping parts. By this means, all the processes of manufacture and inspection are managed with a computer, and it is useful for labor saving and the prevention of mistaken input. This system is centering around the system of the progress management for piping manufacture, and is operated by being coupled with respective systems of production design, order and inventory, mill sheet management and installation management. The management of production design, manufacture, inspection and installation is explained. There is the problem of sticking bar code labels again as the labels become dirty or parts pass through coating and pickling processes. The direct carving of bar codes on parts by laser marker was tried, and it was successful for stainless steel, but in carbon steel pipes, it was hard to read. It is desirable to develop the bar codes which endure until the end of plant life. (K.I.)

  7. Application of laser bar code technology in power fitting evaluation

    Science.gov (United States)

    Yang, Xiaohong; Liu, Shuhuab

    2007-12-01

    In this work, an automatic encoding and management system on power fittings (PFEMS) is developed based on laser bar coding technology. The system can encode power fittings according to their types, structure, dimensions, materials, and technical characteristics. Both the character codes and the laser bar codes of power fittings can be produced from the system. The system can evaluate power fittings and search process-paper automatically. The system analyzes the historical values and technical information of congeneric fittings, and forms formulae of evaluation with recursive analytical method. And then stores the formulae and technical documents into the database for index. Scanning the bar code with a laser bar code reader, accurate evaluation and corresponding process-paper of the fittings can be produced. The software has already been applied in some power stations and worked very well.

  8. Optical System Design For High Speed Bar Code Scanning

    Science.gov (United States)

    Hellekson, Ronald; Reddersen, Brad; Campbell, Scott

    1987-04-01

    Spectra-Physics recently introduced the Model 750 SL scanner for use in the European point-of-sale market, to meet the European requirement for a scanner of less than 13 cm height. The model 750 SL uses a higher density computer designed scan pattern with a retrodirective collection system to scan and detect UPC, EAN, and JAN bar codes. The scanner "reads" these bar codes in such a way that the user need not precisely align the bar code symbol with respect to the window in the scanner even at package speeds up to 100 inches per second. By using a unique geometrical arrangement of mirrors, a polygonal mirror assembly, and a custom-designed plastic bifocal lens, a design was developed to meet these requirements. This paper describes the design of this new low cost scanner, the use of computer-aided design in the development of this scanner, and some observations on the future of bar code scanning.

  9. Application bar-code system for solid radioactive waste management

    International Nuclear Information System (INIS)

    Solid radioactive wastes are generated from the post-irradiated fuel examination facility, the irradiated material examination facility, the research reactor, and the laboratories at KAERI. A bar-code system for a solid radioactive waste management of a research organization became necessary while developing the RAWMIS(Radioactive Waste Management Integration System) which it can generate personal history management for efficient management of a waste, documents, all kinds of statistics. This paper introduces an input and output application program design to do to database with data in the results and a stream process of a treatment that analyzed the waste occurrence present situation and data by bar-code system

  10. Machine-vision-based bar code scanning for long-range applications

    Science.gov (United States)

    Banta, Larry E.; Pertl, Franz A.; Rosenecker, Charles; Rosenberry-Friend, Kimberly A.

    1998-10-01

    Bar code labeling of products has become almost universal in most industries. However, in the steel industry, problems with high temperatures, harsh physical environments and the large sizes of the products and material handling equipment have slowed implementation of bar code based systems in the hot end of the mill. Typical laser-based bar code scanners have maximum scan distances of only 15 feet or so. Longer distance models have been developed which require the use of retro reflective paper labels, but the labels must be very large, are expensive, and cannot stand the heat and physical abuse of the steel mill environment. Furthermore, it is often difficult to accurately point a hand held scanner at targets in bright sunlight or at long distances. An automated product tag reading system based on CCD cameras and computer image processing has been developed by West Virginia University, and demonstrated at the Weirton Steel Corporation. The system performs both the pointing and reading functions. A video camera is mounted on a pan/tilt head, and connected to a personal computer through a frame grabber board. The computer analyzes the images, and can identify product ID tags in a wide-angle scene. It controls the camera to point at each tag and zoom for a closeup picture. The closeups are analyzed and the program need both a barcode and the corresponding alphanumeric code on the tag. This paper describes the camera pointing and bar-code reading functions of the algorithm. A companion paper describes the OCR functions.

  11. CERN access card: Introduction of a bar code

    CERN Multimedia

    Relations with the Host States Service

    2004-01-01

    Before the latest version of the implementation measures relating to Operational Circular No. 2 comes into force, we would like to inform you that, in future, CERN access cards may bear a bar code to transcribe the holder's identification number. Relations with the Host States Service http://www.cern.ch/relations/ Tel. 72848

  12. CERN access cards - Introduction of a bar code (Reminder)

    CERN Multimedia

    Relations with the Host States Service

    2004-01-01

    In accordance with the latest revised version of the implementation measures relating to Operational Circular No. 2, CERN access cards may bear a bar code transcribing the holder's identification number (the revised version of this subsidiary document to the aforementioned Circular will be published shortly). Relations with the Host States Service http://www.cern.ch/relations/ relations.secretariat@cern.ch Tel. 72848

  13. Modeling And Simulation Of Bar Code Scanners Using Computer Aided Design Software

    Science.gov (United States)

    Hellekson, Ron; Campbell, Scott

    1988-06-01

    Many optical systems have demanding requirements to package the system in a small 3 dimensional space. The use of computer graphic tools can be a tremendous aid to the designer in analyzing the optical problems created by smaller and less costly systems. The Spectra Physics grocery store bar code scanner employs an especially complex 3 dimensional scan pattern to read bar code labels. By using a specially written program which interfaces with a computer aided design system, we have simulated many of the functions of this complex optical system. In this paper we will illustrate how a recent version of the scanner has been designed. We will discuss the use of computer graphics in the design process including interactive tweaking of the scan pattern, analysis of collected light, analysis of the scan pattern density, and analysis of the manufacturing tolerances used to build the scanner.

  14. Bar-code technology applied to drug-use evaluation.

    Science.gov (United States)

    Zarowitz, B J; Petitta, A; Mlynarek, M; Touchette, M; Peters, M; Long, P; Patel, R

    1993-05-01

    Bar-code technology was used to determine: (1) patterns in histamine H2-receptor antagonist use and (2) the occurrence of adverse drug effects and drug interactions associated with the use of these agents in critically ill patients. Patients at Henry Ford Hospital (Detroit) receiving histamine H2-receptor antagonists over a two-month period were evaluated. Clinical information was collected in the intensive care units by using a bar-code system. The data-capture menu was based on drug-use-evaluation criteria for H2-receptor antagonists. Data collected in the scanning wands were uploaded into a computer database and were analyzed at the end of the study. Data were collected for 207 patients. Cimetidine was the predominant H2-receptor antagonist used, and the predominant indication was stress-ulcer prophylaxis. Dosing trends followed accepted guidelines for cimetidine dosage adjustment in renal and hepatic failure. Two drug interactions and six adverse drug reactions occurred. Pharmacists made 92 recommendations to the medical staff regarding modification in therapy, involving 32% of the patients. Data collection required an average of 10 minutes per day each for three pharmacists. H2-receptor antagonist use patterns were evaluated in intensive care units through the application of bar-code technology. The speed and efficiency of this automated tool facilitated collection of a large amount of data. PMID:8099468

  15. PCR-free quantitative detection of genetically modified organism from raw materials. An electrochemiluminescence-based bio bar code method.

    Science.gov (United States)

    Zhu, Debin; Tang, Yabing; Xing, Da; Chen, Wei R

    2008-05-15

    A bio bar code assay based on oligonucleotide-modified gold nanoparticles (Au-NPs) provides a PCR-free method for quantitative detection of nucleic acid targets. However, the current bio bar code assay requires lengthy experimental procedures including the preparation and release of bar code DNA probes from the target-nanoparticle complex and immobilization and hybridization of the probes for quantification. Herein, we report a novel PCR-free electrochemiluminescence (ECL)-based bio bar code assay for the quantitative detection of genetically modified organism (GMO) from raw materials. It consists of tris-(2,2'-bipyridyl) ruthenium (TBR)-labeled bar code DNA, nucleic acid hybridization using Au-NPs and biotin-labeled probes, and selective capture of the hybridization complex by streptavidin-coated paramagnetic beads. The detection of target DNA is realized by direct measurement of ECL emission of TBR. It can quantitatively detect target nucleic acids with high speed and sensitivity. This method can be used to quantitatively detect GMO fragments from real GMO products.

  16. Denture bar-coding: An innovative technique in forensic dentistry

    OpenAIRE

    Dineshshankar, Janardhanam; Venkateshwaran, Rajendran; J. Vidhya; Anuradha, R.; Mary, Gold Pealin; Pradeep, R.; Senthileagappan, A. R.

    2015-01-01

    Denture markers play an important role in forensic odontology and also in identifying a person. A number of methods are there for identifying dentures from a less expensive technique to a more expensive technique. Out of different denture markers, the bar-coding system is a way of collecting data from the mobile. Even a huge amount of data can be stored in that. It can be easily incorporated during acrylization of the denture and thus could be helpful in identification. This article reviews t...

  17. Effects Of Substrate Scattering On Bar-Code Scanning Signals

    Science.gov (United States)

    Barkan, Eric; Sklar, David

    1983-04-01

    When a beam of light strikes a piece of paper or similar substrate, a portion of its energy penetrates into the bulk and, due to multiple scattering, may re-emerge at some distance from the point of entry. We refer to this phenomenon as substrate scattering. In this paper we describe a general model for scattering substrates and, using linear systems theory, we investigate its implications for bar-code scanning. We show that the effects of substrate scattering can be represented as a modified reflectance distribution associated with the original printed reflectance pattern. This effective distribution is shown to be independent of the details of scanning system configuration. We show that under a broad range of conditions substrate scattering will decrease modulation and will cause scanners to overestimate barwidths. A specific diffusion model of the scattering process is developed, providing a family of functions which can be used in empirical studies. We conclude that the scattering distributions will not even be approximately Gaussian. Experimental results are presented which are consistent with this conclusion and inconsistent with a Gaussian model. Further experimental results are presented which show that, for typical substrates, depth of modulation may be decreased by 20 percent or more and perceived bar-width increases will be on the order of one mil.

  18. System Design Considerations In Bar-Code Laser Scanning

    Science.gov (United States)

    Barkan, Eric; Swartz, Jerome

    1984-08-01

    The unified transfer function approach to the design of laser barcode scanner signal acquisition hardware is considered. The treatment of seemingly disparate system areas such as the optical train, the scanning spot, the electrical filter circuits, the effects of noise, and printing errors is presented using linear systems theory. Such important issues as determination of depth of modulation, filter specification, tolerancing of optical components, and optimi-zation of system performance in the presence of noise are discussed. The concept of effective spot size to allow for impact of optical system and analog processing circuitry upon depth of modulation is introduced. Considerations are limited primarily to Gaussian spot profiles, but also apply to more general cases. Attention is paid to realistic bar-code symbol models and to implications with respect to printing tolerances.

  19. Nurses' Attitudes Toward the Use of the Bar-coding Medication Administration System

    NARCIS (Netherlands)

    S.D. Marini; A. Hasman; H.A.S. Huijer; H. Dimassi

    2010-01-01

    This study determines nurses' attitudes toward bar-coding medication administration system use. Some of the factors underlying the successful use of bar-coding medication administration systems that are viewed as a connotative indicator of users' attitudes were used to gather data that describe the

  20. Contrast and Comparison Between the Old and New Bar Code for Commodity Management Measures

    Institute of Scientific and Technical Information of China (English)

    Huang Xiaolin; Ma Jing

    2005-01-01

    @@ With the development of socialism market economy, the former Bar Code For Commodity Management Measures (being called Old Measures for short hereafter) issued by the National Bureau of Quality and Technical Supervision can not adapt to the requirement of managing for bar code for commodity.

  1. Bar coded air sample tracking and bar coded loose surface contamination sample tracking: How it can assist in compliance with the DOE's new 10 CFR 835 and the NRC's new 10 CFR 20 regulations

    International Nuclear Information System (INIS)

    The paper describes advance sample tracking and processing techniques which utilize bar code technology for field data collection and count room analysis. Techniques described by the paper include bar coded area air sampling, bar coded portable breathing zone air sampling, and bar coded loose surface contamination sampling. Bar coded sample tracking is explored to demonstrate how it can assist in compliance with new DOE 10 CFR 835 and NRC 10 CFR 20 requirements. Operation of portable bar code readers is explored to provide insight to the advantages of bar coded sample tracking and corresponding sample trending analyses. Case studies involving bar coded sample tracking systems which are in use at NRC facilities, DOE sites, and decommission projects are discussed

  2. Deblurring, Localization and Geometry Correction of 2D QR Bar Codes Using Richardson Lucy Method

    OpenAIRE

    Manpreet Kaur; Amandeep Singh Bhandari

    2014-01-01

    This paper includes the recognition of 2D QR bar codes. This paper describes the deblurring, localization and geometry correction of 2D QR bar codes. The images captured are blurred due motion between the image and the camera. Hence the image containing the QR barcode cannot be read by QR reader. To make the QR barcode readable the images are need to be deblurred. Lucy Richardson method and Weiner Deconvolution Method is used to deblurr and localize the bar code. From both of ...

  3. A new magnetic bar code system based on a magnetic anisotropy detection (abstract)

    Science.gov (United States)

    Sasada, I.; Watanabe, N.

    1996-04-01

    Magnetic bar codes can be used in unclean environments, where widely used optical bar code systems cannot be applied. Readout system for magnetic bar codes can also be made much simpler than optical ones. A new magnetic bar code system is proposed, in which binary information is coded in the sign of tilted angles of magnetic strips from a given standard direction. This scheme is unique compared to the conventional optical bar code, where width or space of the parallel pattern carries information, or an already reported magnetic bar code, where cross sectional shapes of pattern engraved in a ferromagnetic body carries information. Each of the magnetic strips brings about magnetic anisotropy due to its shape effect, hence angular dependent permeability in the proximity of the strip. The sign of the tilted angle of each magnetic strip is detected inductively through the angular dependent permeability by using a magnetic pickup head with a pair of cross-coupled figure-eight coils, where the sign of mutual inductance between the primary and the secondary figure-eight coil has one to one relationship to the sign of the tilted angle. Because the detection of the tilted angle is independent of scanning speed, variation in the scanning speed of the readout head does not affect the performance. In our preliminary study, the proposed magnetic bar code system was examined using pickup head consisting of a pair of cross-coupled 10-turn figure-eight coils which was embedded in a rectangular ferrite rod with cross-shape groove on the top surface of 6.5×3 mm dimension. The head was made thinner in the scanning direction to allow dense alignment of the pattern. Two kinds of pattern were made: the one was by aligning short amorphous wires (5 mm in length and 120 μm in diameter) on the plastic film and the other by using a thin (10 μm in thickness) copper film with tilted slits backed by an amorphous ribbon. These samples of magnetic bar code patterns were scanned with lift-off of

  4. Deblurring, Localization and Geometry Correction of 2D QR Bar Codes Using Richardson Lucy Method

    Directory of Open Access Journals (Sweden)

    Manpreet Kaur

    2014-09-01

    Full Text Available This paper includes the recognition of 2D QR bar codes. This paper describes the deblurring, localization and geometry correction of 2D QR bar codes. The images captured are blurred due motion between the image and the camera. Hence the image containing the QR barcode cannot be read by QR reader. To make the QR barcode readable the images are need to be deblurred. Lucy Richardson method and Weiner Deconvolution Method is used to deblurr and localize the bar code. From both of the methods Lucy Richardson Method is best because this method takes less time for execution than the other method. Simulink Model is used for the Geometry correction of the QR bar code. In future, we would like to investigate the generalization of our algorithm to handle more complicated motion blur.

  5. Study of nurse workarounds in a hospital using bar code medication administration system.

    Science.gov (United States)

    Rack, Laurie L; Dudjak, Linda A; Wolf, Gail A

    2012-01-01

    This study analyzed registered nurse workarounds in an academic medical center using bar code medication administration technology. Nurse focus groups and a survey were used to determine the frequency and potential causes of workarounds. More than half of the nurses surveyed indicated that they administered medications without scanning the patient or medications during the last shift worked. Benefits of this study include considerations when implementing bar code medication administration technology that may minimize the development of these workarounds in practice. PMID:22202186

  6. Speckle revisited: analysis of speckle noise in bar-code scanning systems

    Science.gov (United States)

    Marom, Emanuel; Kresic-Juric, Sasa; Bergstein, Leonard

    2001-06-01

    Laser beams used for bar-code scanning exhibit speckle noise generated by the roughness of the surface on which bar-codes are printed. Statistical properties of a photodetector signal that integrates a time-varying speckle pattern falling on its aperture are analyzed in detail. We derive simple closed form expressions for the auto-correlation function and power spectral density of the detector current for general form scanning beams with arbitrary field distributions. Theoretical calculations are illustrated by numerical simulations.

  7. Analysis of Edge Detection in Bar Code Symbols: An Overview and Open Problems

    OpenAIRE

    Saša Krešić-Jurić

    2012-01-01

    Accurate edge localization is essential in bar code decoding. Since speckle noise is the most dominant form of noise in laser bar code scanners, it is important to fully understand its effects on edge detection. Starting with the basic statistical properties of speckle patterns, we present stochastic analysis of speckle noise. We derive the autocorrelation function and power spectral density (PSD) of the noise in terms of intensity distribution of the scanning beam. We then ...

  8. The application of PDA and 2D bar code in material fuel storage management system

    International Nuclear Information System (INIS)

    This paper extends a management system based on PDA and 2D bar code technology, system design and solutions concerned with domestic transfer, storehouse entry and setting, transfer among storehouses, physical inventory are described as well. The system fits business processes well and optimizes data acquisition and processing effectively by u sing the following key technologies: bar code material and paste stand under radioactive conditions, two dimensional storage space emulation, information cascade protection. (authors)

  9. Multi-hop optical label switching with coherent detected spectral amplitude code labels

    Science.gov (United States)

    Cao, Yongsheng

    Based on label stacking principles and coherent detection, we present a two-hop, coherent detected spectral amplitude code (SAC) labeled system to accomplish ultrafast packet forwarding for packet-switched metropolitan area networks. An optical switching network with two forwarding nodes, two 156 Mb/s SAC labels, and 40 Gb/s differential quadrature phase shift keying (DQPSK) payloads is demonstrated by computer simulation. The bit error rate (BER) performances of coherent detected SAC labels and high speed payload over 160 km fiber after two hops transmission are accessed, respectively.

  10. Integrating bar-code devices with computerized MC and A systems

    International Nuclear Information System (INIS)

    Over the past seven years, Los Alamos National Laboratory developed several generations of computerized nuclear materials control and accountability (MC and A) systems for tracking and reporting the storage, movement, and management of nuclear materials at domestic and international facilities. During the same period, Oak Ridge National Laboratory was involved with automated data acquisition (ADA) equipment, including installation of numerous bar-code scanning stations at various facilities to serve as input devices to computerized systems. Bar-code readers, as well as other ADA devices, reduce input errors, provide faster input, and allow the capture of data in remote areas where workstations do not exist. Los Alamos National Laboratory and Oak Ridge National Laboratory teamed together to implement the integration of bar-code hardware technology with computerized MC and A systems. With the expertise of both sites, the two technologies were successfully merged with little difficulty. Bar-code input is now available with several functions of the MC and A systems: material movements within material balance areas (MBAs), material movements between MBAs, and physical inventory verification. This paper describes the various components required for the integration of these MC and A systems with the installed bar-code reader devices and the future directions for these technologies

  11. Analysis of Edge Detection in Bar Code Symbols: An Overview and Open Problems

    Directory of Open Access Journals (Sweden)

    Saša Krešić-Jurić

    2012-01-01

    Full Text Available Accurate edge localization is essential in bar code decoding. Since speckle noise is the most dominant form of noise in laser bar code scanners, it is important to fully understand its effects on edge detection. Starting with the basic statistical properties of speckle patterns, we present stochastic analysis of speckle noise. We derive the autocorrelation function and power spectral density (PSD of the noise in terms of intensity distribution of the scanning beam. We then study the signal-to-noise ratio for signals that result from scanning different configurations of edges. Next, we consider statistical properties of edge localization error caused by speckle noise. We show that the standard deviation of the error is determined by the PSD of the noise and relative positions of edges in a bar code symbol. Based on the analysis presented here, we propose new criteria for system design.

  12. Using bar codes to manage radwaste in a nuclear power facility

    International Nuclear Information System (INIS)

    Maintaining accountability, and tracking the location of radioactive waste, has been simplified through the use of bar codes at the Peach Bottom and Limerick Power Plants. A system has been developed which utilizes portable, programmable bar code readers and a microcomputer to collect and report pertinent data on the generation and location of radwaste in the plant. The system, which was customized for each plant, was designed to collect data at the work place through the use of the portable bar code readers and menu cards. The program was designed in a modular format for easy modification and expansion and the system has been adapted for the tracking of equipment, tools, instruments, and respirators. The benefit from this inventory management system is more timely and accurate information for the control of radwaste generation, handling, storage, and shipping. The improved control has resulted in more efficient, cost effective radwaste operations, reduced radiation exposure to personnel, and a cleaner, more orderly plant

  13. Verification of Advective Bar Elements Implemented in the Aria Thermal Response Code.

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Brantley [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-01-01

    A verification effort was undertaken to evaluate the implementation of the new advective bar capability in the Aria thermal response code. Several approaches to the verification process were taken : a mesh refinement study to demonstrate solution convergence in the fluid and the solid, visually examining the mapping of the advective bar element nodes to the surrounding surfaces, and a comparison of solutions produced using the advective bars for simple geometries with solutions from commercial CFD software . The mesh refinement study has shown solution convergence for simple pipe flow in both temperature and velocity . Guidelines were provided to achieve appropriate meshes between the advective bar elements and the surrounding volume. Simulations of pipe flow using advective bars elements in Aria have been compared to simulations using the commercial CFD software ANSYS Fluent (r) and provided comparable solutions in temperature and velocity supporting proper implementation of the new capability. Verification of Advective Bar Elements iv Acknowledgements A special thanks goes to Dean Dobranich for his guidance and expertise through all stages of this effort . His advice and feedback was instrumental to its completion. Thanks also goes to Sam Subia and Tolu Okusanya for helping to plan many of the verification activities performed in this document. Thank you to Sam, Justin Lamb and Victor Brunini for their assistance in resolving issues encountered with running the advective bar element model. Finally, thanks goes to Dean, Sam, and Adam Hetzler for reviewing the document and providing very valuable comments.

  14. 76 FR 66235 - Bar Code Technologies for Drugs and Biological Products; Retrospective Review Under Executive...

    Science.gov (United States)

    2011-10-26

    ... technology adoption have proceeded since 2004 had the Bar Code Final Rule not gone into effect? 11. What are hospitals' and other health-care facilities' forecasts for technology adoption once incentives in the...'' (76 FR 3821). One of the provisions in the new Executive order is the affirmation of...

  15. Method and apparatus for reading lased bar codes on shiny-finished fuel rod cladding tubes

    International Nuclear Information System (INIS)

    This patent describes, in a nuclear fuel rod identification system, a method of reading a bar code etched directly on a surface of a nuclear fuel rod. It comprises: defining a pair of light diffuser surfaces adjacent one another but in oppositely inclined relation to a beam of light emitted from a light reader; positioning a fuel rod, having a cylindrical surface portion with a bar code etched directly thereon, relative to the light diffuser surfaces such that the surfaces are disposed adjacent to and in oppositely inclined relation along opposite sides of the fuel rod surface portion and the fuel rod surface portion is aligned with the beam of light emitted from the light reader; directing the beam of light on the bar code on fuel rod cylindrical surface portion such that the light is reflected therefrom onto one of the light diffuser surfaces; and receiving and reading the reflected light from the bar code via the one of the light diffuser surfaces to the light reader

  16. Challenges implementing bar-coded medication administration in the emergency room in comparison to medical surgical units.

    Science.gov (United States)

    Glover, Nancy

    2013-03-01

    Bar-coded medication administration has been successfully implemented and utilized to decrease medication errors at a number of hospitals in recent years. The purpose of this article was to discuss the varying success in utilization of bar-coded medication administration on medical-surgical units and in the emergency department. Utilization reports were analyzed to better understand the challenges between the units. Many factors negatively impacted utilization in the emergency department, including the inability to use bar-coded medication administration for verbal orders or to document medications distributed by the prescribing providers, unique aspects of emergency department nursing workflow, additional steps to chart when using bar-coded medication administration, and alert fatigue. Hardware problems affected all users. Bar-coded medication administration in its current form is more suitable for use on medical-surgical floors than in the emergency department. New solutions should be developed for bar-coded medication administration in the emergency department, keeping in mind requirements to chart medications when there is no order in the system, document medications distributed by prescribing providers, adapt to unpredictable nursing workflow, minimize steps to chart with bar-coded medication administration, limit alerts to those that are clinically meaningful, and choose reliable hardware with adequate bar-code scanning capability. PMID:23321481

  17. Laser bar code applied in computer aided design of power fittings

    Science.gov (United States)

    Yang, Xiaohong; Yang, Fan

    2010-10-01

    A computer aided process planning system is developed based on laser bar code technology to automatize and standardize processing-paper making. The system sorts fittings by analyzing their types, structures, dimensions, materials, and technics characteristics, groups and encodes the fittings with similar technology characteristics base on the theory of Group Technology (GT). The system produces standard technology procedures using integrative-parts method and stores them into technics databases. To work out the technology procedure of fittings, the only thing for users need to do is to scan the bar code of fittings with a laser code reader. The system can produce process-paper using decision trees method and then print the process-cards automatically. The software has already been applied in some power stations and is praised by the users.

  18. Choosing between an apple and a chocolate bar: the impact of health and taste labels.

    Directory of Open Access Journals (Sweden)

    Suzanna E Forwood

    Full Text Available Increasing the consumption of fruit and vegetables is a central component of improving population health. Reasons people give for choosing one food over another suggest health is of lower importance than taste. This study assesses the impact of using a simple descriptive label to highlight the taste as opposed to the health value of fruit on the likelihood of its selection. Participants (N=439 were randomly allocated to one of five groups that varied in the label added to an apple: apple; healthy apple; succulent apple; healthy and succulent apple; succulent and healthy apple. The primary outcome measure was selection of either an apple or a chocolate bar as a dessert. Measures of the perceived qualities of the apple (taste, health, value, quality, satiety and of participant characteristics (restraint, belief that tasty foods are unhealthy, BMI were also taken. When compared with apple selection without any descriptor (50%, the labels combining both health and taste descriptors significantly increased selection of the apple ('healthy & succulent' 65.9% and 'succulent & healthy' 62.4%, while the use of a single descriptor had no impact on the rate of apple selection ('healthy' 50.5% and 'succulent' 52%. The strongest predictors of individual dessert choice were the taste score given to the apple, and the lack of belief that healthy foods are not tasty. Interventions that emphasize the taste attributes of healthier foods are likely to be more effective at achieving healthier diets than those emphasizing health alone.

  19. Preliminary investigation of acoustic bar codes for short-range underwater communications

    Science.gov (United States)

    Jones, Dennis F.

    2005-09-01

    In March 2005, underwater acoustic communications experiments were carried out from the DRDC Atlantic research vessel CFAV QUEST. A battery-operated BATS20 transmitter and a broadband barrel-stave flextensional transducer were used to broadcast noise containing acoustic bar code (ABC) information. The ABCs are silent frequency bands of fixed duration that resemble retail bar codes when viewed in a spectrogram. Two sites were selected for the experiments. The first was a shallow-water area west of the Berry Islands in the Bahamas, and the second was a deep-water site south of the Western Bank on the Scotian Shelf. Two receiver systems were deployed; autonomous, variable-buoyancy Stealth Buoys resting on the bottom at the shallow site, and drifting AN/SSQ-53F sonobuoys fitted with GPS at the deep site. Results from these experiments will be presented and future work will be discussed.

  20. Improving Patient Safety by Identifying Side Effects from Introducing Bar Coding in Medication Administration

    OpenAIRE

    Patterson, Emily S.; Cook, Richard I.; Marta L. Render

    2002-01-01

    Objective. In addition to providing new capabilities, the introduction of technology in complex, sociotechnical systems, such as health care and aviation, can have unanticipated side effects on technical, social, and organizational dimensions. To identify potential accidents in the making, the authors looked for side effects from a natural experiment, the implementation of bar code medication administration (BCMA), a technology designed to reduce adverse drug events (ADEs).

  1. Use of a bar code scanner to improve the utility and flexibility of record and verify systems used in radiation therapy

    International Nuclear Information System (INIS)

    Record and verify systems used in radiation therapy serve a useful purpose in verification of machine parameters for each radiation field and monitoring the treatment as it is administered. There are, however, limitations as to the completeness of this monitoring. These restrictions are primarily due to design limitations of accelerators, which provide only a limited number of hardwired signals for use by such systems. The extent of the signals provided varies among manufacturers. As a result, some commonly used treatment accessories, such as blocking trays, may not be recognized by these systems. Additionally, current commercial record and verify systems cannot be expanded to accommodate institution-specific, customized treatment accessories or devices for positioning or immobilization of patients. This paper describes a complementary approach to providing device detection using a bar code scanner to read coded labels mounted on treatment accessories and download the data into the record and verify system for processing. A microcomputer-based system employing a portable bar code scanner was developed to evaluate the potential of this concept. Implications of adding bar code scanners to record and verify systems are discussed

  2. The design of the CMOS wireless bar code scanner applying optical system based on ZigBee

    Science.gov (United States)

    Chen, Yuelin; Peng, Jian

    2008-03-01

    The traditional bar code scanner is influenced by the length of data line, but the farthest distance of the wireless bar code scanner of wireless communication is generally between 30m and 100m on the market. By rebuilding the traditional CCD optical bar code scanner, a CMOS code scanner is designed based on the ZigBee to meet the demands of market. The scan system consists of the CMOS image sensor and embedded chip S3C2401X, when the two dimensional bar code is read, the results show the inaccurate and wrong code bar, resulted from image defile, disturber, reads image condition badness, signal interference, unstable system voltage. So we put forward the method which uses the matrix evaluation and Read-Solomon arithmetic to solve them. In order to construct the whole wireless optics of bar code system and to ensure its ability of transmitting bar code image signals digitally with long distances, ZigBee is used to transmit data to the base station, and this module is designed based on image acquisition system, and at last the wireless transmitting/receiving CC2430 module circuit linking chart is established. And by transplanting the embedded RTOS system LINUX to the MCU, an applying wireless CMOS optics bar code scanner and multi-task system is constructed. Finally, performance of communication is tested by evaluation software Smart RF. In broad space, every ZIGBEE node can realize 50m transmission with high reliability. When adding more ZigBee nodes, the transmission distance can be several thousands of meters long.

  3. Analysis of the technology acceptance model in examining hospital nurses' behavioral intentions toward the use of bar code medication administration.

    Science.gov (United States)

    Song, Lunar; Park, Byeonghwa; Oh, Kyeung Mi

    2015-04-01

    Serious medication errors continue to exist in hospitals, even though there is technology that could potentially eliminate them such as bar code medication administration. Little is known about the degree to which the culture of patient safety is associated with behavioral intention to use bar code medication administration. Based on the Technology Acceptance Model, this study evaluated the relationships among patient safety culture and perceived usefulness and perceived ease of use, and behavioral intention to use bar code medication administration technology among nurses in hospitals. Cross-sectional surveys with a convenience sample of 163 nurses using bar code medication administration were conducted. Feedback and communication about errors had a positive impact in predicting perceived usefulness (β=.26, Pmodel predicting for behavioral intention, age had a negative impact (β=-.17, Pmodel explained 24% (Ptechnology.

  4. Overcoming Barriers to the Implementation of a Pharmacy Bar Code Scanning System for Medication Dispensing: A Case Study

    OpenAIRE

    Nanji, Karen C.; Cina, Jennifer; Patel, Nirali; Churchill, William; Gandhi, Tejal K.; Poon, Eric G.

    2009-01-01

    Technology has great potential to reduce medication errors in hospitals. This case report describes barriers to, and facilitators of, the implementation of a pharmacy bar code scanning system to reduce medication dispensing errors at a large academic medical center. Ten pharmacy staff were interviewed about their experiences during the implementation. Interview notes were iteratively reviewed to identify common themes. The authors identified three main barriers to pharmacy bar code scanning s...

  5. Constellation labeling optimization for bit-interleaved coded APSK

    Science.gov (United States)

    Xiang, Xingyu; Mo, Zijian; Wang, Zhonghai; Pham, Khanh; Blasch, Erik; Chen, Genshe

    2016-05-01

    This paper investigates the constellation and mapping optimization for amplitude phase shift keying (APSK) modulation, which is deployed in Digital Video Broadcasting Satellite - Second Generation (DVB-S2) and Digital Video Broadcasting - Satellite services to Handhelds (DVB-SH) broadcasting standards due to its merits of power and spectral efficiency together with the robustness against nonlinear distortion. The mapping optimization is performed for 32-APSK according to combined cost functions related to Euclidean distance and mutual information. A Binary switching algorithm and its modified version are used to minimize the cost function and the estimated error between the original and received data. The optimized constellation mapping is tested by combining DVB-S2 standard Low-Density Parity-Check (LDPC) codes in both Bit-Interleaved Coded Modulation (BICM) and BICM with iterative decoding (BICM-ID) systems. The simulated results validate the proposed constellation labeling optimization scheme which yields better performance against conventional 32-APSK constellation defined in DVB-S2 standard.

  6. Effects of spherical aberration on the laser beam of a bar code scanner

    Science.gov (United States)

    Tang, Hong

    1998-08-01

    The modulation transfer function of bar code scanning is a useful tool for evaluating the performance of the scanning laser beam. Understanding the behavior of the scanning laser system near the end of its depth of focus is of particular interest because it may lead to the development of techniques that could effective extend the depth of focus. In the article the MTF at focus and the two extremes of the depth of focus are presented. The presence of spherical aberration in the scanning laser beam generally reduces the depth of focus. The effects of the spherical aberration to the MTF is presented and discussed.

  7. Use of bar-code technology in MC and A system

    International Nuclear Information System (INIS)

    Full text: Significant problem during the treatment of nuclear materials is the usage of reliable, rapid, integrate automated systems of nuclear material control and account to reduce the dose loading of personnel. One of the directions to solve the indicated problems is the usage of bar-code technology. Such integrated system should include protection of materials, measuring of materials, and record of materials and drawing up of an inventory list. It is especially important for the enterprises, in which the enriched uranium and other nuclear materials, under IAEA warranties, are utilized. According to US assistance program in the field of MC and A, NSC KIPT has been received indispensable equipment and software, including equipment of nondestructive analysis and automated inventory material accounting system (AIMAS), which was intended for modernizing of nuclear material account system in NSC KIPT. The purpose of operations was estimation of generalized procedures on both MC and A and nondestructive analysis, and updating them so that they might obey the specific conditions of the Enterprise and demands of the Ukraine Regulatory Administration. In NSC KIPT, which is the largest nuclear and physics research center in Ukraine, the measures on enactment of bar-code technology for nuclear materials control and account with the usage of equipment and software of US leading firms (Intermec, Prodigy Max, Tharo Systems, Inc) have been conducting since 1999. During the introduction of this technology, the software on nuclear material control and account (AIMAS data base) has been installed on NSC KIPT computers. The structure of the NSC KIPT's facility has been determined according to demands of the State and IAEA demands. The items of information on the structure of the Facility, and data, which was verified and prepared for input, on nuclear material for each key measuring point of inventory quantity of the material have been set into nuclear material control and

  8. Performance of Manchester-coded payload in an optical FSK labeling scheme

    DEFF Research Database (Denmark)

    Zhang, Jianfeng; Chi, Nan; Holm-Nielsen, Pablo Villanueva;

    2003-01-01

    The modulation crosstalk between combined frequency-shift keying (FSK) and intensity modulation (IM) in an optical label-switching network is analyzed both theoretically and experimentally. A comparison between the performance of nonreturn-to-zero (NRZ) and Manchester-coded payload is made. It is...... shown that Manchester coding of the payload helps to suppress the crosstalk introduced into, the optical FSK label, thus achieving better network performance than NRZ coding....

  9. High-speed two-dimensional bar-code detection system with time-sharing laser light emission method

    Science.gov (United States)

    Wakaumi, Hiroo; Nagasawa, Chikao

    2000-12-01

    A novel twodimensional bar-code detection system with time-sharing light emission laser diodes is proposed. A bias current allowing the laser diode to improve the light output rise time is optimized to slightly below the threshold of the diode, so that channel cross-talk among three-layer bar-code signals caused by the bias light can be kept small and a high-speed pulse modulation drive operation can be achieved. A prototype system for a three-layer bar code has achieved an effective scanning speed two and nine tenths times that of conventional scanners. It is estimated from the detection range that the number of time-sharing light emission laser diodes can be increased to at least four, when the current detection amplifier with a bandwidth of 6.4 MHz is used.

  10. Equipment Inventory Management and Transaction Recording Using Bar Coding Scheme via VB6

    Directory of Open Access Journals (Sweden)

    Geoffrey T. Salvador, PECE

    2016-06-01

    Full Text Available The aim of the study is to implement bar coding system developed through the VB6 and Microsoft Access as mechanism for the PUP ECE Laboratory Transaction recording and monitoring. The study was concerned on proper documenting and managing the daily transaction of the ECE Laboratory with the AutoLab System.Results showed that the AutoLab System effectively automated the recording of transactions merging the existing manual method into one recording mechanism. The Automated Laboratory coined as AutoLab merged the ECE Room Utilization Log Book, ECE Borrower’s Slip and the ECE Transaction Log Book into one complete package in terms of transaction recording and equipment inventory monitoring

  11. Speckle Noise in Bar-Code Scanning Systems -Power Spectral Density and SNR

    Science.gov (United States)

    Marom, Emanuel; KrěIć-Juri, SǎA.; Bergstein, Leonard

    2003-01-01

    Laser-based flying-spot scanners are strongly affected by speckle that is intrinsic to coherent illumination of diffusing targets. In such systems information is usually extracted by processing the derivative of a photodetector signal that results from collecting over the detector's aperture the scattered light of a laser beam scanning a bar code. Because the scattered light exhibits a time-varying speckle pattern, the signal is corrupted by speckle noise. In this paper we investigate the power spectral density and total noise power of such signals. We also analyze the influence of speckle noise on edge detection and derive estimates for a signal-to-noise ratio when a laser beam scans different sequences of edges. The theory is illustrated by applying the results to Gaussian scanning beams for which we derive closed form expressions.

  12. Towards a spectrum-based bar code for identification of weakly fluorescent microparticles

    International Nuclear Information System (INIS)

    Spectrally resolved detection of fluorescent probes can be used to identify multiple labeled target molecules in an unknown mixture. We study how the spectral shape, the experimental noise, and the number of spectral detection channels affect the success of identification of weakly fluorescent beads on basis of their emission spectra. The proposed formalism allows to estimate the performance of the spectral identification procedure with a given set of spectral codes on the basis of the reference spectra only. We constructed a simple prism-based setup for spectral detection and demonstrate that seven distinct but overlapping spectral codes realized by combining up to three fluorescent dyes bound to a single bead in a barcode-based manner can be reliably identified. The procedure allows correct identification even in the presence of known autofluorescence background stronger than the actual signal. (paper)

  13. Self-regulation in the workplace : codes of conduct, social labelling and socially responsible investment

    OpenAIRE

    Urminsky, Michael

    2001-01-01

    Examines the context in which voluntary private initiatives are developing. Reviews 258 codes of conduct, looks at labour issues covered by the codes and considers the relationship between the codes and international labour standards. Investigates social labelling programmes and socially responsible investment initiatives.

  14. Stable isotope labeling strategy based on coding theory

    International Nuclear Information System (INIS)

    We describe a strategy for stable isotope-aided protein nuclear magnetic resonance (NMR) analysis, called stable isotope encoding. The basic idea of this strategy is that amino-acid selective labeling can be considered as “encoding and decoding” processes, in which the information of amino acid type is encoded by the stable isotope labeling ratio of the corresponding residue and it is decoded by analyzing NMR spectra. According to the idea, the strategy can diminish the required number of labelled samples by increasing information content per sample, enabling discrimination of 19 kinds of non-proline amino acids with only three labeled samples. The idea also enables this strategy to combine with information technologies, such as error detection by check digit, to improve the robustness of analyses with low quality data. Stable isotope encoding will facilitate NMR analyses of proteins under non-ideal conditions, such as those in large complex systems, with low-solubility, and in living cells

  15. Stable isotope labeling strategy based on coding theory

    Energy Technology Data Exchange (ETDEWEB)

    Kasai, Takuma; Koshiba, Seizo; Yokoyama, Jun; Kigawa, Takanori, E-mail: kigawa@riken.jp [RIKEN Quantitative Biology Center (QBiC), Laboratory for Biomolecular Structure and Dynamics (Japan)

    2015-10-15

    We describe a strategy for stable isotope-aided protein nuclear magnetic resonance (NMR) analysis, called stable isotope encoding. The basic idea of this strategy is that amino-acid selective labeling can be considered as “encoding and decoding” processes, in which the information of amino acid type is encoded by the stable isotope labeling ratio of the corresponding residue and it is decoded by analyzing NMR spectra. According to the idea, the strategy can diminish the required number of labelled samples by increasing information content per sample, enabling discrimination of 19 kinds of non-proline amino acids with only three labeled samples. The idea also enables this strategy to combine with information technologies, such as error detection by check digit, to improve the robustness of analyses with low quality data. Stable isotope encoding will facilitate NMR analyses of proteins under non-ideal conditions, such as those in large complex systems, with low-solubility, and in living cells.

  16. Use of bar-code technology in MC and A system

    International Nuclear Information System (INIS)

    Full text: Significant problem during the treatment with nuclear materials is the usage of reliable, rapid, integrant automated systems of nuclear material control and account. Thus the dose loading of attending technical personnel is essentially reduced. One of the directions of the solution of the indicated problems is the usage of bar-code technology. Such integrated system should include protection of materials, measuring of materials, and record of materials and drawing up of an inventory list. Especially it is important for the enterprises, on which the enriched uranium and other nuclear materials, which are under IAEA warranties, are utilized. According to US assistance program in the field of MC and A, NSC KIPT has been received indispensable equipment and software, including equipment of nondestructive analysis and automated inventory material accounting system (AIMAS), which was intended for modernizing of nuclear material account system in NSC KIPT. The purpose of operations was estimation of generalized procedures on both MC and A and nondestructive analysis, and updating them so that they might obey the specific conditions of the Enterprise and demands of the Ukraine Regulatory Administration. In NSC KIPT, which is the largest nuclear and physics research center in Ukraine, the measures on enactment of bar-code technology for nuclear materials control and account with the usage of equipment and software of US leading firms (Intermec, Prodigy Max, Tharo Systems, Inc) have been conducting since 1999. During the introduction of this technology, it has been installed the software on nuclear material control and account (AIMAS data base), which was intended for this activities, on NSC KIPT computers. The structure of the NSC KIPT's facility has been determined according to demands of the State and IAEA demands. The key measuring points of inventory quantity has been determined in nuclear material balance zone and the concrete computers, on which is kept

  17. Coherent spectral amplitude coded label detection for DQPSK payload signals in packet-switched metropolitan area networks

    DEFF Research Database (Denmark)

    Osadchiy, Alexey Vladimirovich; Guerrero Gonzalez, Neil; Jensen, Jesper Bevensee;

    2011-01-01

    We report on an experimental demonstration of a frequency swept local oscillator-based spectral amplitude coding (SAC) label detection for DQPSK signals after 40km of fiber transmission. Label detection was performed for a 10.7Gbaud DQPSK signal labeled with a SAC label composed of four-frequency......We report on an experimental demonstration of a frequency swept local oscillator-based spectral amplitude coding (SAC) label detection for DQPSK signals after 40km of fiber transmission. Label detection was performed for a 10.7Gbaud DQPSK signal labeled with a SAC label composed of four...

  18. Scanning micro-mirrors: from bar-code scanning to spectroscopy

    Science.gov (United States)

    Zimmer, F.; Grueger, H.; Heberer, A.; Sandner, T.; Wolter, A.; Schenk, H.

    2005-08-01

    Micro Opto Electro Mechanical Systems (MOEMS) reach more and more importance in technical applications. They are smaller than conventional devices, less expensive when fabricated in higher numbers and offer new options concerning reliability and measuring methods. Resonant movable micro-mirrors produced as single crystalline chips with CMOS-compatible technologies provide a broad field of applications. In this paper, we will present different micro-mirrors, which are developed by the Fraunhofer IPMS in Dresden, Germany. They have different layouts and are thus suitable for several applications. Fabricated 1D-mirrors with mechanical angles of +/- 16° can be used for laser deflection in bar-code-scanners, 2D-mirrors with different sizes and frequencies are suitable for imaging, displaying etc. Furthermore processes to apply diffractive structures on the micro-mirror surface were developed, showing an increased efficiency in the first diffraction order. Thus a micro-spectrometer has been built up, working in a wavelength range of 900-2500 nm. Due to the Czerny-Turner set-up, only one fast single InGaAs-photodiode is required.

  19. DNA bar coding and pyrosequencing to analyze adverse events in therapeutic gene transfer.

    Science.gov (United States)

    Wang, Gary P; Garrigue, Alexandrine; Ciuffi, Angela; Ronen, Keshet; Leipzig, Jeremy; Berry, Charles; Lagresle-Peyrou, Chantal; Benjelloun, Fatine; Hacein-Bey-Abina, Salima; Fischer, Alain; Cavazzana-Calvo, Marina; Bushman, Frederic D

    2008-05-01

    Gene transfer has been used to correct inherited immunodeficiencies, but in several patients integration of therapeutic retroviral vectors activated proto-oncogenes and caused leukemia. Here, we describe improved methods for characterizing integration site populations from gene transfer studies using DNA bar coding and pyrosequencing. We characterized 160,232 integration site sequences in 28 tissue samples from eight mice, where Rag1 or Artemis deficiencies were corrected by introducing the missing gene with gamma-retroviral or lentiviral vectors. The integration sites were characterized for their genomic distributions, including proximity to proto-oncogenes. Several mice harbored abnormal lymphoproliferations following therapy--in these cases, comparison of the location and frequency of isolation of integration sites across multiple tissues helped clarify the contribution of specific proviruses to the adverse events. We also took advantage of the large number of pyrosequencing reads to show that recovery of integration sites can be highly biased by the use of restriction enzyme cleavage of genomic DNA, which is a limitation in all widely used methods, but describe improved approaches that take advantage of the power of pyrosequencing to overcome this problem. The methods described here should allow integration site populations from human gene therapy to be deeply characterized with spatial and temporal resolution.

  20. A code-based approach for labeling in complex irregular regions

    Institute of Scientific and Technical Information of China (English)

    Zhi-long LI; Jun-jie CAO; Xiu-ping LIU; Zhi-xun SU

    2009-01-01

    Labeling information in a complex irregular region is a useful procedure occurring frequently in sheet metal and the furniture industry which will be beneficial in parts management. A fast code-based labeler (FCBL) is proposed to accomplish this objective in this paper. The region is first discretized, and then encoded by the Freeman encoding technique for providing the 2D regional information by 1D codes with redundancies omitted. We enhance the encoding scheme to make it more suitable for our complex problem. Based on the codes, searching algorithms are designed and can be extended with customized constraints. In addition, by introducing a smart optimal direction estimation, the labeling speed and accuracy of FCBL are significantly improved. Experiments with a large range of real data gained from industrial factories demonstrate the stability and millisecond-level speed of FCBL. The proposed method has been integrated into a shipbuilding CAD system, and plays a very important role in ship parts labeling process.

  1. Label swapper device for spectral amplitude coded optical packet networks monolithically integrated on InP.

    Science.gov (United States)

    Muñoz, P; García-Olcina, R; Habib, C; Chen, L R; Leijtens, X J M; de Vries, T; Robbins, D; Capmany, J

    2011-07-01

    In this paper the design, fabrication and experimental characterization of an spectral amplitude coded (SAC) optical label swapper monolithically integrated on Indium Phosphide (InP) is presented. The device has a footprint of 4.8x1.5 mm2 and is able to perform label swapping operations required in SAC at a speed of 155 Mbps. The device was manufactured in InP using a multiple purpose generic integration scheme. Compared to previous SAC label swapper demonstrations, using discrete component assembly, this label swapper chip operates two order of magnitudes faster. PMID:21747509

  2. Overcoming barriers to the implementation of a pharmacy bar code scanning system for medication dispensing: a case study.

    Science.gov (United States)

    Nanji, Karen C; Cina, Jennifer; Patel, Nirali; Churchill, William; Gandhi, Tejal K; Poon, Eric G

    2009-01-01

    Technology has great potential to reduce medication errors in hospitals. This case report describes barriers to, and facilitators of, the implementation of a pharmacy bar code scanning system to reduce medication dispensing errors at a large academic medical center. Ten pharmacy staff were interviewed about their experiences during the implementation. Interview notes were iteratively reviewed to identify common themes. The authors identified three main barriers to pharmacy bar code scanning system implementation: process (training requirements and process flow issues), technology (hardware, software, and the role of vendors), and resistance (communication issues, changing roles, and negative perceptions about technology). The authors also identified strategies to overcome these barriers. Adequate training, continuous improvement, and adaptation of workflow to address one's own needs mitigated process barriers. Ongoing vendor involvement, acknowledgment of technology limitations, and attempts to address them were crucial in overcoming technology barriers. Staff resistance was addressed through clear communication, identifying champions, emphasizing new information provided by the system, and facilitating collaboration. PMID:19567797

  3. A novel all-optical label processing based on multiple optical orthogonal codes sequences for optical packet switching networks

    Science.gov (United States)

    Zhang, Chongfu; Qiu, Kun; Xu, Bo; Ling, Yun

    2008-05-01

    This paper proposes an all-optical label processing scheme that uses the multiple optical orthogonal codes sequences (MOOCS)-based optical label for optical packet switching (OPS) (MOOCS-OPS) networks. In this scheme, each MOOCS is a permutation or combination of the multiple optical orthogonal codes (MOOC) selected from the multiple-groups optical orthogonal codes (MGOOC). Following a comparison of different optical label processing (OLP) schemes, the principles of MOOCS-OPS network are given and analyzed. Firstly, theoretical analyses are used to prove that MOOCS is able to greatly enlarge the number of available optical labels when compared to the previous single optical orthogonal code (SOOC) for OPS (SOOC-OPS) network. Then, the key units of the MOOCS-based optical label packets, including optical packet generation, optical label erasing, optical label extraction and optical label rewriting etc., are given and studied. These results are used to verify that the proposed MOOCS-OPS scheme is feasible.

  4. Orthogonal modulation system with Manchester-coded payload and frequency-shift keying label

    Science.gov (United States)

    Yang, Liu; Luo, Fengguang

    2016-04-01

    We propose an orthogonal modulation scheme with 40 Gb/s Manchester-coded (MC) payload and 2.5 Gb/s frequency-shift keying (FSK) label. The high-speed FSK label is generated by an FSK modulator, which consists of two modulators, while MC payload is generated by an intensity modulator. Simulation results show that the available extinction ratio of FSK and amplitude-shift keying with MC payload can improve from 5.1 to 11.2 dB, compared with the traditional not-return-to-zero payload. The receiver sensitivities of both MC payload and FSK label show a remarkable improvement.

  5. Establishing and evaluating bar-code technology in blood sampling system: a model based on human centered human-centered design method

    OpenAIRE

    Chou, Shin-Shang; Yan, Hsiu-Fang; Huang, Hsiu-Ya; Tseng, Kuan-Jui; Kuo, Shu-Chen

    2012-01-01

    This study intended to use a human-centered design study method to develop a bar-code technology in blood sampling process. By using the multilevel analysis to gather the information, the bar-code technology has been constructed to identify the patient’s identification, simplify the work process, and prevent medical error rates. A Technology Acceptance Model questionnaire was developed to assess the effectiveness of system and the data of patient’s identification and sample errors were collec...

  6. A NEW LABELING SEARCH ALGORITHM FOR BIT-INTERLEAVED CODED MODULATION WITH ITERATIVE DECODING

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Bit-Interleaved Coded Modulation with Iterative Decoding (BICM-ID) is a bandwidth efficient transmission, where the bit error rate is reduced through the iterative information exchange between the inner demapper and the outer decoder. The choice of the symbol mapping is the crucial design parameter. This paper indicates that the Harmonic Mean of the Minimum Squared Euclidean (HMMSE) distance is the best criterion for the mapping design. Based on the design criterion of the HMMSE distance, a new search algorithm to find the optimized labeling maps for BICM-ID system is proposed. Numerical results and performance comparison show that the new labeling search method has a low complexity and outperforms other labeling schemes using other design criterion in BICM-ID system, therefore it is an optimized labeling method.

  7. Color bar coding the BRCA1 gene on combed DNA: a useful strategy for detecting large gene rearrangements.

    Science.gov (United States)

    Gad, S; Aurias, A; Puget, N; Mairal, A; Schurra, C; Montagna, M; Pages, S; Caux, V; Mazoyer, S; Bensimon, A; Stoppa-Lyonnet, D

    2001-05-01

    Genetic linkage data have shown that alterations of the BRCA1 gene are responsible for the majority of hereditary breast and ovarian cancers. BRCA1 germline mutations, however, are found less frequently than expected. Mutation detection strategies, which are generally based on the polymerase chain reaction, therefore focus on point and small gene alterations. These approaches do not allow for the detection of large gene rearrangements, which also can be involved in BRCA1 alterations. Indeed, a few of them, spread over the entire BRCA1 gene, have been detected recently by Southern blotting or transcript analysis. We have developed an alternative strategy allowing a panoramic view of the BRCA1 gene, based on dynamic molecular combing and the design of a full four-color bar code of the BRCA1 region. The strategy was tested with the study of four large BRCA1 rearrangements previously reported. In addition, when screening a series of 10 breast and ovarian cancer families negatively tested for point mutation in BRCA1/2, we found an unreported 17-kb BRCA1 duplication encompassing exons 3 to 8. The detection of rearrangements as small as 2 to 6 kb with respect to the normal size of the studied fragment is achieved when the BRCA1 region is divided into 10 fragments. In addition, as the BRCA1 bar code is a morphologic approach, the direct observation of complex and likely underreported rearrangements, such as inversions and insertions, becomes possible. PMID:11284038

  8. Frequency-swept coherently detected spectral amplitude code for flexible implicit optical label switching

    Institute of Scientific and Technical Information of China (English)

    Yongsheng Cao; Fushen Chen; Zhigao Yang

    2011-01-01

    A new optical label switching system with coherently detected implicit spectral amplitude code(SAC)labels is proposed in this letter.The implicit SAC labels are recognized using a frequency-swept local light source oscillator.Intensity modulation payloads of 625 Mb/s and 1.25 Gb/s are considered.Label and pavload bit error rate(BER) performances are assessed and compared by simulations.The results reveal that,at a BER value of 10-9,-32.4dBm label received power can be obtained.In addition,8.3-dB optical signal-to-noise ratio(OSNR) is obtained when carrying a payload of 625 Mb/s.The label BER value hardly reaches 10-9 if the payload bit rate is at 1.25 Gb/s; however,a high payload bit rate only has little influence on received payload quality at a BER value of 10-9.Finally,a payload of 1.25 Gb/s could obtain-28.2 dBm received power and 9.5-dB OSNR.

  9. Retrieval-based Face Annotation by Weak Label Regularized Local Coordinate Coding.

    Science.gov (United States)

    Wang, Dayong; Hoi, Steven C H; He, Ying; Zhu, Jianke; Mei, Tao; Luo, Jiebo

    2013-08-01

    Retrieval-based face annotation is a promising paradigm of mining massive web facial images for automated face annotation. This paper addresses a critical problem of such paradigm, i.e., how to effectively perform annotation by exploiting the similar facial images and their weak labels which are often noisy and incomplete. In particular, we propose an effective Weak Label Regularized Local Coordinate Coding (WLRLCC) technique, which exploits the principle of local coordinate coding in learning sparse features, and employs the idea of graph-based weak label regularization to enhance the weak labels of the similar facial images. We present an efficient optimization algorithm to solve the WLRLCC task. We conduct extensive empirical studies on two large-scale web facial image databases: (i) a Western celebrity database with a total of $6,025$ persons and $714,454$ web facial images, and (ii)an Asian celebrity database with $1,200$ persons and $126,070$ web facial images. The encouraging results validate the efficacy of the proposed WLRLCC algorithm. To further improve the efficiency and scalability, we also propose a PCA-based approximation scheme and an offline approximation scheme (AWLRLCC), which generally maintains comparable results but significantly saves much time cost. Finally, we show that WLRLCC can also tackle two existing face annotation tasks with promising performance.

  10. Drug-laden 3D biodegradable label using QR code for anti-counterfeiting of drugs.

    Science.gov (United States)

    Fei, Jie; Liu, Ran

    2016-06-01

    Wiping out counterfeit drugs is a great task for public health care around the world. The boost of these drugs makes treatment to become potentially harmful or even lethal. In this paper, biodegradable drug-laden QR code label for anti-counterfeiting of drugs is proposed that can provide the non-fluorescence recognition and high capacity. It is fabricated by the laser cutting to achieve the roughness over different surface which causes the difference in the gray levels on the translucent material the QR code pattern, and the micro mold process to obtain the drug-laden biodegradable label. We screened biomaterials presenting the relevant conditions and further requirements of the package. The drug-laden microlabel is on the surface of the troches or the bottom of the capsule and can be read by a simple smartphone QR code reader application. Labeling the pill directly and decoding the information successfully means more convenient and simple operation with non-fluorescence and high capacity in contrast to the traditional methods. PMID:27040262

  11. NeuCode Labeling in Nematodes: Proteomic and Phosphoproteomic Impact of Ascaroside Treatment in Caenorhabditis elegans.

    Science.gov (United States)

    Rhoads, Timothy W; Prasad, Aman; Kwiecien, Nicholas W; Merrill, Anna E; Zawack, Kelson; Westphall, Michael S; Schroeder, Frank C; Kimble, Judith; Coon, Joshua J

    2015-11-01

    The nematode Caenorhabditis elegans is an important model organism for biomedical research. We previously described NeuCode stable isotope labeling by amino acids in cell culture (SILAC), a method for accurate proteome quantification with potential for multiplexing beyond the limits of traditional stable isotope labeling by amino acids in cell culture. Here we apply NeuCode SILAC to profile the proteomic and phosphoproteomic response of C. elegans to two potent members of the ascaroside family of nematode pheromones. By consuming labeled E. coli as part of their diet, C. elegans nematodes quickly and easily incorporate the NeuCode heavy lysine isotopologues by the young adult stage. Using this approach, we report, at high confidence, one of the largest proteomic and phosphoproteomic data sets to date in C. elegans: 6596 proteins at a false discovery rate ≤ 1% and 6620 phosphorylation isoforms with localization probability ≥75%. Our data reveal a post-translational signature of pheromone sensing that includes many conserved proteins implicated in longevity and response to stress.

  12. A high-speed 12-layer two-dimensional bar code detection system with wideband photodetection amplifier and balanced raster scanner

    Science.gov (United States)

    Wakaumi, Hiroo; Ajiki, Hiroshi

    1998-12-01

    A high-speed 12-layer 2D bar-code detection system (BCDS) consisting of a photodetection amplifier with an amplification-type current-voltage converter and a balanced raster scanner combined with the complementary light emission drive method for laser diodes, has been developed in order to provide both a high effective scanning speed and multi-layer bar-code detection. This BCDS performs 1,250 scan/s, which is two and a half times the scanning speed of a conventional bar-code detection system. A new theoretical modulation model that gives an accurate model for laser scanning beam traces obtained by the balanced raster scanner is proposed. This model allows an optimum BCDS to be designed easily.

  13. Retrieval-based face annotation by weak label regularized local coordinate coding.

    Science.gov (United States)

    Wang, Dayong; Hoi, Steven C H; He, Ying; Zhu, Jianke; Mei, Tao; Luo, Jiebo

    2014-03-01

    Auto face annotation, which aims to detect human faces from a facial image and assign them proper human names, is a fundamental research problem and beneficial to many real-world applications. In this work, we address this problem by investigating a retrieval-based annotation scheme of mining massive web facial images that are freely available over the Internet. In particular, given a facial image, we first retrieve the top $(n)$ similar instances from a large-scale web facial image database using content-based image retrieval techniques, and then use their labels for auto annotation. Such a scheme has two major challenges: 1) how to retrieve the similar facial images that truly match the query, and 2) how to exploit the noisy labels of the top similar facial images, which may be incorrect or incomplete due to the nature of web images. In this paper, we propose an effective Weak Label Regularized Local Coordinate Coding (WLRLCC) technique, which exploits the principle of local coordinate coding by learning sparse features, and employs the idea of graph-based weak label regularization to enhance the weak labels of the similar facial images. An efficient optimization algorithm is proposed to solve the WLRLCC problem. Moreover, an effective sparse reconstruction scheme is developed to perform the face annotation task. We conduct extensive empirical studies on several web facial image databases to evaluate the proposed WLRLCC algorithm from different aspects. The experimental results validate its efficacy. We share the two constructed databases "WDB" (714,454 images of 6,025 people) and "ADB" (126,070 images of 1,200 people) with the public. To further improve the efficiency and scalability, we also propose an offline approximation scheme (AWLRLCC) which generally maintains comparable results but significantly reduces the annotation time. PMID:24457510

  14. Bar Code Technology of Interactive Teaching%条形码技术的互动教学

    Institute of Scientific and Technical Information of China (English)

    林胜青

    2014-01-01

    学习现代科学技术,并结合在生活中实际应用,尽量提倡师生用互动式教学,推动当今的现代化教育,提高教育质量。本文介绍利用互动式教学方法,讲授条形码的制作原理及实际应用。%Learning modern science and technology,and connecting with the practical application in our daily life,try to advocate using interactive teaching between teachers and students,promote the today's modern education,improve the quality of education. This article shows that using interactive teaching methods,teaching of bar code principle and prac-tical application.

  15. Bar code hotel: diverse interactions of semi-autonomous entities under the partial control of multiple operators

    Science.gov (United States)

    Hoberman, Perry

    1995-03-01

    In this paper I describe an interactive installation that was produced in 1994 as one of eight Art and Virtual Environments projects sponsored by the Banff Center for the Arts. The installation, Bar Code Hotel, makes use of a number of strategies to create a casual, social, multi-person interface. Among the goals was to investigate methods that would minimize any significant learning curve, allowing visitors to immediately interact with a virtual world in a meaningful way. By populating this virtual world with semi-independent entities that could be directed by participants even as these entities were interacting with each other, a rich and heterogeneous experience was produced in which a variety of relationships between human participants and virtual objects could be examined. The paper will describe some of the challenges of simultaneously processing multiple input sources affecting a virtual environment in which each object already has its own ongoing behavior.

  16. Design of Bar Code Automatic Printing System Based on LabVIEW%基于LabVIEW的条码自动打印系统设计

    Institute of Scientific and Technical Information of China (English)

    周先飞; 李敏; 杨会伟

    2016-01-01

    汽车行业中各个设备都来自不同的供应商,要实现产品溯源需从条码去区别。针对汽车大灯产品检测系统之后的自动打印条码,实现检测过程的自动化要求。提出了采用单片机制作的数据采集卡和LabVIEW建立的上位机软件,实现对检测完好的产品进行条码的自动打印输出,在上位机中可以对不同型号的产品进行条码的切换,在生产线上具有完全自动化功能,经现场使用,稳定性良好。%In automotive industry ,each equipment comes from different suppliers ,it needs bar codes to distinguish the products. Towards the automatic printing of bar codes after testing of headlight product , the paper realizes the automation of testing process. This paper presents MCU for DAQ and labVIEV for upper computer softwave ,to realize the automatic printing of bar codes tested ,it can change the bar codes in upper computer for differen products. The system has automation function ,and has good stability proved by field use.

  17. BAR-CODE BASED WEIGHT MEASUREMENT STATION FOR PHYSICAL INVENTORY TAKING OF PLUTONIUM OXIDE CONTAINERS AT THE MINING AND CHEMICAL COMBINE RADIOCHEMICAL REPROCESSING PLANT NEAR KRASNOYARSK, SIBERIA

    International Nuclear Information System (INIS)

    This paper describes the technical tasks being implemented to computerize the physical inventory taking (PIT) at the Mining and Chemical Combine (Gorno-Khimichesky Kombinat, GKhK) radiochemical plant under the US/Russian cooperative nuclear material protection, control, and accounting (MPC and A) program. Under the MPC and A program, Lab-to-Lab task agreements with GKhK were negotiated that involved computerized equipment for item verification and confirmatory measurement of the Pu containers. Tasks under Phase I cover the work for demonstrating the plan and procedures for carrying out the comparison of the Pu container identification on the container with the computerized inventory records. In addition to the records validation, the verification procedures include the application of bar codes and bar coded TIDs to the Pu containers. Phase II involves the verification of the Pu content. A plan and procedures are being written for carrying out confirmatory measurements on the Pu containers

  18. 基于链码跟踪的Data Matrix二维条码快速识别%Quick identification of Data Matrix two-dimensional bar code based on chain code tracking

    Institute of Scientific and Technical Information of China (English)

    徐义钊; 白瑞林; 余震虹; 吉峰

    2012-01-01

    为实现工业现场中Data Matrix二维条码的快速识别,提出一种基于链码跟踪、直线段提取的条码快速识别方法.首先采用Sobel算子提取图像边缘;然后基于链码跟踪方法,跟踪图像的边缘点,记录链码;接着根据快速直线段提取方法,将直线相似度低于阈值的线段剔除,结合线形连接方法合并断裂线段,并使用长度判别剔除不可靠的线段;最后结合Data Matrix二维条码的特征,定位Data Matrix二维条码.实际测试表明,该识别方法能够快速、准确地定位二维条码区域,识别正确率可达99.39%以上,具有实时性强、可靠性好等特点,满足工业现场要求.%A two-dimensional bar code recognition method based on chain code tracking and straight line segment extraction was proposed in order to realize quick identification of the Data Matrix two-dimensional bar code in the industrial field. Firstly, the Sobel operator was used to extract the edge of image. Secondly, the image edge points were tracked and chain codes were recorded based on chain code tracking method. Thirdly, line segment whose straight line similarity was below the threshold was removed with fast straight line segment extraction method. The fracture line was combined with the linear connection method and the unreliable line was excluded by length discrimination. Finally, the Data Matrix bar code was located with the characteristics of the Data Matrix two-dimensional bar code. The application test shows that the two-dimensional bar code area can be quickly and accurately located by the recognition method with the recognition rate of 99. 39%. The proposed method is ready to meet the requirements of industrial field with strong real-time ability and high reliability.

  19. Ontology-supported processing of clinical text using medical knowledge integration for multi-label classification of diagnosis coding

    CERN Document Server

    Waraporn, Phanu; Clayton, Gareth

    2010-01-01

    This paper discusses the knowledge integration of clinical information extracted from distributed medical ontology in order to ameliorate a machine learning-based multi-label coding assignment system. The proposed approach is implemented using a decision tree based cascade hierarchical technique on the university hospital data for patients with Coronary Heart Disease (CHD). The preliminary results obtained show a satisfactory finding.

  20. Isotope Coded Protein Labeling analysis of plasma specimens from acute severe dengue fever patients

    Directory of Open Access Journals (Sweden)

    Fragnoud Romain

    2012-10-01

    Full Text Available Abstract Background Dengue fever is the most important arthropod born viral disease of public health significance. Although most patients suffer only from flu-like symptoms, a small group of patient experiences more severe forms of the disease. To contribute to a better understanding of its pathogenesis this study aims to identify proteins differentially expressed in a pool of five viremic plasma from severe dengue patients relative to a pool of five non-severe dengue patients. Results The use of Isotope Coded Protein Labeling (ICPLTM to analyze plasma depleted of twenty high-abundance proteins allowed for the identification of 51 differentially expressed proteins, which were characterized by mass spectrometry. Using quantitative ELISA, three of these proteins (Leucine-rich glycoprotein 1, Vitamin D binding-protein and Ferritin were confirmed as having an increased expression in a panel of severe dengue plasma. The proteins identified as overexpressed by ICPLTM in severe dengue plasma involve in clear up action after cell injury, tissue coherence and immune defense. Conclusion This ICPLTM study evaluating differences between acute severe dengue plasmas and acute non-severe dengue plasmas suggests that the three proteins identified are overexpressed early in the course of the disease. Their possible use as biomarkers for the prognostic of disease severity is discussed.

  1. Visualization and analysis of microtubule dynamics using dual color-coded display of plus-end labels.

    Directory of Open Access Journals (Sweden)

    Amy K Garrison

    Full Text Available Investigating spatial and temporal control of microtubule dynamics in live cells is critical to understanding cell morphogenesis in development and disease. Tracking fluorescently labeled plus-end-tracking proteins over time has become a widely used method to study microtubule assembly. Here, we report a complementary approach that uses only two images of these labels to visualize and analyze microtubule dynamics at any given time. Using a simple color-coding scheme, labeled plus-ends from two sequential images are pseudocolored with different colors and then merged to display color-coded ends. Based on object recognition algorithms, these colored ends can be identified and segregated into dynamic groups corresponding to four events, including growth, rescue, catastrophe, and pause. Further analysis yields not only their spatial distribution throughout the cell but also provides measurements such as growth rate and direction for each labeled end. We have validated the method by comparing our results with ground-truth data derived from manual analysis as well as with data obtained using the tracking method. In addition, we have confirmed color-coded representation of different dynamic events by analyzing their history and fate. Finally, we have demonstrated the use of the method to investigate microtubule assembly in cells and provided guidance in selecting optimal image acquisition conditions. Thus, this simple computer vision method offers a unique and quantitative approach to study spatial regulation of microtubule dynamics in cells.

  2. Equipment management system based on 2-dimensional bar code technology%基于二维码技术的装备管理系统的研究

    Institute of Scientific and Technical Information of China (English)

    戴军

    2013-01-01

      本文提出了依托二维码技术构建装备管理系统的构想,阐述了基于二维码的装备管理系统的架构和基本功能。该系统结合数据库技术和网络技术,可实现装备信息的装备状态标识、自动录入、实时数据传送等功能。建立基于二维码等自动识别技术的装备管理管理系统是实现装备全寿命管理的信息化、自动化的有效手段,本文对此有一定的实用性。%The paper puts forward the idea of building equipment management system based on the 2-dimensional bar code technology,describes the equipment management system of 2-dimensional bar code structure and basic function. The system can realize the equipment information of equipment state identification,automatic input,real-time data transmission and other functions.To establish the practical equipment management system based on 2-dimensional bar code automatic identification technology is the efficient method for the informatization and automatization of the equipments’ life cycle management and what this paper presents can serve as the reference for this task.

  3. Establishing and evaluating bar-code technology in blood sampling system: a model based on human centered human-centered design method.

    Science.gov (United States)

    Chou, Shin-Shang; Yan, Hsiu-Fang; Huang, Hsiu-Ya; Tseng, Kuan-Jui; Kuo, Shu-Chen

    2012-01-01

    This study intended to use a human-centered design study method to develop a bar-code technology in blood sampling process. By using the multilevel analysis to gather the information, the bar-code technology has been constructed to identify the patient's identification, simplify the work process, and prevent medical error rates. A Technology Acceptance Model questionnaire was developed to assess the effectiveness of system and the data of patient's identification and sample errors were collected daily. The average scores of 8 items users' perceived ease of use was 25.21(3.72), 9 items users' perceived usefulness was 28.53(5.00), and 14 items task-technology fit was 52.24(7.09), the rate of patient identification error and samples with order cancelled were down to zero, however, new errors were generated after the new system deployed; which were the position of barcode stickers on the sample tubes. Overall, more than half of nurses (62.5%) were willing to use the new system. PMID:24199057

  4. Label swapper device for spectral amplitude coded optical packet networks monolithically integrated on InP

    OpenAIRE

    Muñoz, P.; García-Olcina, R; Habib, C; Chen, LR; Leijtens, XJM Xaveer; Vries, de, H.J.C.; Robbins, DJ David; Capmany, J José

    2011-01-01

    This paper was published in OPTICS EXPRESS and is made available as an electronic reprint with the permission of OSA. The paper can be found at the following URL on the OSA website: http://dx.doi.org/10.1364/OE.19.013540. Systematic or multiple reproduction or distribution to multiple locations via electronic or other means is prohibited and is subject to penalties under law In this paper the design, fabrication and experimental characterization of an spectral amplitude coded (SAC) optical...

  5. 标刻在金属零件上的二维条码数据提取方法%2-D Bar Code Data Extraction on Metal Parts

    Institute of Scientific and Technical Information of China (English)

    王伟; 何卫平; 雷蕾; 林清松; 李夏霜

    2012-01-01

    针对金属零件上二维条码光照分布不均、点扩散、对比度低与污染干扰等问题,提出一种基于原灰度图像小区域相邻模块对比提取二维条码数据的算法.首先通过峰度值排序法及模块区域微调法由粗到精定位每个二维条码模块位置,然后基于原灰度图像利用遗传算法提取二维条码的数据信息,得到最终的提取结果.与传统二维条码数据提取算法的实验结果证明,该算法对于复杂金属背景上的二维条码识读具有更高的可靠性.%This paper describes a 2D bar code extraction approach that is capable of processing pictures of 2D bar codes on metal parts with uneven distribution of light intensity, point spread, low contrast and pollution interference. The algorithm uses kurtosis value-sorting and module area fine tuning to locate each module's position which is detected from coarse-level to fine-level, then the final extraction data of 2D bar code is obtained by a genetic algorithm based on the original gray-scale image. Compared with traditional methods, the proposed algorithm has higher reliability for 2D bar code extraction on complex metal parts.

  6. BEIJING BARS

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Cappuccino Bar Cappuccino Bar, at the intersection of Dongzhimenwai Dajie and Sanlitun Beijie, Beijing's most vibrant nightlife area, is a hot new destination for European food lovers. With its perfect combination of both energy and tranquility, and surrounded by diplomatic compounds, it is conveniently located near other Beijing destinations including Lady Street

  7. LABELING OPTIONS FOR POSTAL SHIPMENTS BY PASSIVE RFID TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Ondrej Maslák

    2015-09-01

    Full Text Available This article discusses the topic of labeling postal shipments by passive radio frequency identification (RFID tags. Every delivery company needs to have all necessary information for every single postal shipment package it carries. Shipment package labeling is essential for processing and tracking the postal shipments along its delivery process. Using RFID technology for the process brings advantages in more efficient delivery and data collection along with regular information updates of shipment status across complete delivery chain.In this article, we focused on the problem of logical log of key shipment package information into EPC memory of the RFID smart label. We have taken into account the National postal administrator and its current system of shipment labeling. In the end, we presented a design for conversion of contemporary labeling using bar codes into labeling using RFID tags.

  8. Comparison of a Label-Free Quantitative Proteomic Method Based on Peptide Ion Current Area to the Isotope Coded Affinity Tag Method

    Directory of Open Access Journals (Sweden)

    Young Ah Goo

    2008-01-01

    Full Text Available Recently, several research groups have published methods for the determination of proteomic expression profiling by mass spectrometry without the use of exogenously added stable isotopes or stable isotope dilution theory. These so-called label-free, methods have the advantage of allowing data on each sample to be acquired independently from all other samples to which they can later be compared in silico for the purpose of measuring changes in protein expression between various biological states. We developed label free software based on direct measurement of peptide ion current area (PICA and compared it to two other methods, a simpler label free method known as spectral counting and the isotope coded affinity tag (ICAT method. Data analysis by these methods of a standard mixture containing proteins of known, but varying, concentrations showed that they performed similarly with a mean squared error of 0.09. Additionally, complex bacterial protein mixtures spiked with known concentrations of standard proteins were analyzed using the PICA label-free method. These results indicated that the PICA method detected all levels of standard spiked proteins at the 90% confidence level in this complex biological sample. This finding confirms that label-free methods, based on direct measurement of the area under a single ion current trace, performed as well as the standard ICAT method. Given the fact that the label-free methods provide ease in experimental design well beyond pair-wise comparison, label-free methods such as our PICA method are well suited for proteomic expression profiling of large numbers of samples as is needed in clinical analysis.

  9. A highly reliable coding scheme for space station inventory labels%空间站物资标签高可靠性编码方案

    Institute of Scientific and Technical Information of China (English)

    许成鑫; 魏传锋; 李学东

    2014-01-01

    文章提出了一种用于空间站物资管理的RFID(Radio Frequency Identification)系统电子标签信息编码方案。在该方案中,对电子标签中存储的物资基本信息进行纠错编码,从而增强了信息的可靠性。理论分析表明,与存储更多物资基本信息的原始方案相比,在相同条件下,采用合适的纠错码,新方案的信息可靠性更高。数值仿真结果与理论分析结果相吻合。%This paper proposes an information coding scheme for electric labels in the RFID (Radio Frequency Identification) system for the inventory management in a space station. In this scheme, the electric label codes with the error control coding are made to identify the information of the inventories. The analysis results show that the information reliability of this scheme is better than that of the original scheme storing more identification information by choosing a kind of an appropriate error control coding under the same condition. The simulation results are consistent with the analysis results.

  10. Pharmaceutical Industry Off-label Promotion and Self-regulation: A Document Analysis of Off-label Promotion Rulings by the United Kingdom Prescription Medicines Code of Practice Authority 2003-2012.

    Directory of Open Access Journals (Sweden)

    Andreas Vilhelmsson

    2016-01-01

    Full Text Available European Union law prohibits companies from marketing drugs off-label. In the United Kingdom--as in some other European countries, but unlike the United States--industry self-regulatory bodies are tasked with supervising compliance with marketing rules. The objectives of this study were to (1 characterize off-label promotion rulings in the UK compared to the whistleblower-initiated cases in the US and (2 shed light on the UK self-regulatory mechanism for detecting, deterring, and sanctioning off-label promotion.We conducted structured reviews of rulings by the UK self-regulatory authority, the Prescription Medicines Code of Practice Authority (PMCPA, between 2003 and 2012. There were 74 off-label promotion rulings involving 43 companies and 65 drugs. Nineteen companies were ruled in breach more than once, and ten companies were ruled in breach three or more times over the 10-y period. Drawing on a typology previously developed to analyse US whistleblower complaints, we coded and analysed the apparent strategic goals of each off-label marketing scheme and the practices consistent with those alleged goals. 50% of rulings cited efforts to expand drug use to unapproved indications, and 39% and 38% cited efforts to expand beyond approved disease entities and dosing strategies, respectively. The most frequently described promotional tactic was attempts to influence prescribers (n = 72, 97%, using print material (70/72, 97%, for example, advertisements (21/70, 30%. Although rulings cited prescribers as the prime target of off-label promotion, competing companies lodged the majority of complaints (prescriber: n = 16, 22%, versus companies: n = 42, 57%. Unlike US whistleblower complaints, few UK rulings described practices targeting consumers (n = 3, 4%, payers (n = 2, 3%, or company staff (n = 2, 3%. Eight UK rulings (11% pertaining to six drugs described promotion of the same drug for the same off-label use as was alleged by whistleblowers in the US

  11. Pharmaceutical Industry Off-label Promotion and Self-regulation: A Document Analysis of Off-label Promotion Rulings by the United Kingdom Prescription Medicines Code of Practice Authority 2003–2012

    Science.gov (United States)

    Vilhelmsson, Andreas; Davis, Courtney; Mulinari, Shai

    2016-01-01

    Background European Union law prohibits companies from marketing drugs off-label. In the United Kingdom—as in some other European countries, but unlike the United States—industry self-regulatory bodies are tasked with supervising compliance with marketing rules. The objectives of this study were to (1) characterize off-label promotion rulings in the UK compared to the whistleblower-initiated cases in the US and (2) shed light on the UK self-regulatory mechanism for detecting, deterring, and sanctioning off-label promotion. Methods and Findings We conducted structured reviews of rulings by the UK self-regulatory authority, the Prescription Medicines Code of Practice Authority (PMCPA), between 2003 and 2012. There were 74 off-label promotion rulings involving 43 companies and 65 drugs. Nineteen companies were ruled in breach more than once, and ten companies were ruled in breach three or more times over the 10-y period. Drawing on a typology previously developed to analyse US whistleblower complaints, we coded and analysed the apparent strategic goals of each off-label marketing scheme and the practices consistent with those alleged goals. 50% of rulings cited efforts to expand drug use to unapproved indications, and 39% and 38% cited efforts to expand beyond approved disease entities and dosing strategies, respectively. The most frequently described promotional tactic was attempts to influence prescribers (n = 72, 97%), using print material (70/72, 97%), for example, advertisements (21/70, 30%). Although rulings cited prescribers as the prime target of off-label promotion, competing companies lodged the majority of complaints (prescriber: n = 16, 22%, versus companies: n = 42, 57%). Unlike US whistleblower complaints, few UK rulings described practices targeting consumers (n = 3, 4%), payers (n = 2, 3%), or company staff (n = 2, 3%). Eight UK rulings (11%) pertaining to six drugs described promotion of the same drug for the same off-label use as was alleged by

  12. QR Codes 101

    Science.gov (United States)

    Crompton, Helen; LaFrance, Jason; van 't Hooft, Mark

    2012-01-01

    A QR (quick-response) code is a two-dimensional scannable code, similar in function to a traditional bar code that one might find on a product at the supermarket. The main difference between the two is that, while a traditional bar code can hold a maximum of only 20 digits, a QR code can hold up to 7,089 characters, so it can contain much more…

  13. 基于ARM的物品精准定位和二维条码扫描系统设计%Design of Scanning Two-Dimensional Bar Code and Precise Positioning System Based on ARM

    Institute of Scientific and Technical Information of China (English)

    姚立; 刘幺和

    2012-01-01

    GPS positioning and two-dimensional bar code scanning system based on ARM is presented, using the linux operating system and the associated software is provided. System can tin ly locate the positon of the goods on the transporting way and timely read the infor-mation in the two-dimensional code of the goods. Thereby increasing the efficiency of the system.%文章提出了一种以嵌入式ARM为核心,以GPS定位和二维条码扫描为基础的系统,采用Linux操作系统,并给出了相关的软件程序设计.系统可以在物品运输的途中实时的定位,并且还可以实时的了解物品上二维码的信息,从而提高了系统的效率.

  14. 二维码技术在高校智能化管理中的应用探讨%The Application of Two-dimensional Bar Code Technology to University Intelligence Management

    Institute of Scientific and Technical Information of China (English)

    马莉

    2012-01-01

    Two-dimensional bar code technology has been widely applied to a variety of departments and industries due to its informative feature, high confidentiality and security, low cost, easy fabrication, high reliability of deco- ding and ability to resist damage and correct errors. This article probes into the application of two-dimensional bar code technology to campus safety, library, archives information, students and large equipment management in univer- sities, which provides a new thought on research for the smart campus construction.%二维条码技术以信息容量大、保密好和防伪性高、成本低廉且容易制造、译码可靠率高、抗损纠错能力强等特点已经开始普遍应用于各个部门和行业中。探讨了二维码技术在高校校园安全、图书馆、档案信息、学生、大型设备管理方面的应用,为高校智能校园建设提供了新的研究思路。

  15. Digital Equivalent Data System for XRF Labeling of Objects

    Science.gov (United States)

    Schramm, Harry F.; Kaiser, Bruce

    2005-01-01

    A digital equivalent data system (DEDS) is a system for identifying objects by means of the x-ray fluorescence (XRF) spectra of labeling elements that are encased in or deposited on the objects. As such, a DEDS is a revolutionary new major subsystem of an XRF system. A DEDS embodies the means for converting the spectral data output of an XRF scanner to an ASCII alphanumeric or barcode label that can be used to identify (or verify the assumed or apparent identity of) an XRF-scanned object. A typical XRF spectrum of interest contains peaks at photon energies associated with specific elements on the Periodic Table (see figure). The height of each spectral peak above the local background spectral intensity is proportional to the relative abundance of the corresponding element. Alphanumeric values are assigned to the relative abundances of the elements. Hence, if an object contained labeling elements in suitably chosen proportions, an alphanumeric representation of the object could be extracted from its XRF spectrum. The mixture of labeling elements and for reading the XRF spectrum would be compatible with one of the labeling conventions now used for bar codes and binary matrix patterns (essentially, two-dimensional bar codes that resemble checkerboards). A further benefit of such compatibility is that it would enable the conversion of the XRF spectral output to a bar or matrix-coded label, if needed. In short, a process previously used only for material composition analysis has been reapplied to the world of identification. This new level of verification is now being used for "authentication."

  16. Bar dimensions and bar shapes in estuaries

    Science.gov (United States)

    Leuven, Jasper; Kleinhans, Maarten; Weisscher, Steven; van der Vegt, Maarten

    2016-04-01

    Estuaries cause fascinating patterns of dynamic channels and shoals. Intertidal sandbars are valuable habitats, whilst channels provide access to harbors. We still lack a full explanation and classification scheme for the shapes and dimensions of bar patterns in natural estuaries, in contrast with bars in rivers. Analytical physics-based models suggest that bar length in estuaries increases with flow velocity, tidal excursion length or estuary width, depending on which model. However, these hypotheses were never validated for lack of data and experiments. We present a large dataset and determine the controls on bar shape and dimensions in estuaries, spanning bar lengths from centimeters (experiments) to 10s of kilometers length. First, we visually identified and classified 190 bars, measured their dimensions (width, length, height) and local braiding index. Data on estuarine geometry and tidal characteristics were obtained from governmental databases and literature on case studies. We found that many complex bars can be seen as simple elongated bars partly cut by mutually evasive ebb- and flood-dominated channels. Data analysis shows that bar dimensions scale with estuary dimensions, in particular estuary width. Breaking up the complex bars in simple bars greatly reduced scatter. Analytical bar theory overpredicts bar dimensions by an order of magnitude in case of small estuarine systems. Likewise, braiding index depends on local width-to-depth ratio, as was previously found for river systems. Our results suggest that estuary dimensions determine the order of magnitude of bar dimensions, while tidal characteristics modify this. We will continue to model bars numerically and experimentally. Our dataset on tidal bars enables future studies on the sedimentary architecture of geologically complex tidal deposits and enables studying effects of man-induced perturbations such as dredging and dumping on bar and channel patterns and habitats.

  17. Deciphering Systemic Wound Responses of the Pumpkin Extrafascicular Phloem by Metabolomics and Stable Isotope-Coded Protein Labeling1[C][W

    Science.gov (United States)

    Gaupels, Frank; Sarioglu, Hakan; Beckmann, Manfred; Hause, Bettina; Spannagl, Manuel; Draper, John; Lindermayr, Christian; Durner, Jörg

    2012-01-01

    In cucurbits, phloem latex exudes from cut sieve tubes of the extrafascicular phloem (EFP), serving in defense against herbivores. We analyzed inducible defense mechanisms in the EFP of pumpkin (Cucurbita maxima) after leaf damage. As an early systemic response, wounding elicited transient accumulation of jasmonates and a decrease in exudation probably due to partial sieve tube occlusion by callose. The energy status of the EFP was enhanced as indicated by increased levels of ATP, phosphate, and intermediates of the citric acid cycle. Gas chromatography coupled to mass spectrometry also revealed that sucrose transport, gluconeogenesis/glycolysis, and amino acid metabolism were up-regulated after wounding. Combining ProteoMiner technology for the enrichment of low-abundance proteins with stable isotope-coded protein labeling, we identified 51 wound-regulated phloem proteins. Two Sucrose-Nonfermenting1-related protein kinases and a 32-kD 14-3-3 protein are candidate central regulators of stress metabolism in the EFP. Other proteins, such as the Silverleaf Whitefly-Induced Protein1, Mitogen Activated Protein Kinase6, and Heat Shock Protein81, have known defensive functions. Isotope-coded protein labeling and western-blot analyses indicated that Cyclophilin18 is a reliable marker for stress responses of the EFP. As a hint toward the induction of redox signaling, we have observed delayed oxidation-triggered polymerization of the major Phloem Protein1 (PP1) and PP2, which correlated with a decline in carbonylation of PP2. In sum, wounding triggered transient sieve tube occlusion, enhanced energy metabolism, and accumulation of defense-related proteins in the pumpkin EFP. The systemic wound response was mediated by jasmonate and redox signaling. PMID:23085839

  18. Barred Owl [ds8

    Data.gov (United States)

    California Department of Resources — These data define the current range of Barred and hybrid Barred/Spotted Owls in California. The current range includes the coastal mountains of northern California...

  19. DNA Bar-Coding for Phytoplasma Identification

    DEFF Research Database (Denmark)

    Makarova, Olga; Contaldo, Nicoletta; Paltrinieri, Samanta;

    2013-01-01

    Phytoplasma identi fi cation has proved dif fi cult due to their inability to be maintained in vitro. DNA barcoding is an identi fi cation method based on comparison of a short DNA sequence with known sequences from a database. A DNA barcoding tool has been developed for phytoplasma identi fi cat...

  20. 基于红外条码的盲人扑克游戏辅助仪的设计%Design and implementation of blind poker game auxiliary instrument based on infrared scanning bar code

    Institute of Scientific and Technical Information of China (English)

    景亚霓; 杨海平

    2014-01-01

    The paper designs a blind poker game auxiliary instrument based on bar code technology, embedded system and voice chip technology. The instrument has the characteristics of compact structure , simple and convenient operation and embed popular poker game program, thus users can conveniently select the type of game according to their interest. Its main feature is that it can broadcast information that others played poker and supplies situation of yourself poker in hands by earplug if need. The auxiliary instrument makes the blind to get poke information by "listen" instead of "touch", so that blind and low vision people can play cards as a normal person even if he does not know Braille. In other hand, some problem can be avoided, such as mistake of player distinguishing Braille.%设计了一款基于集条形码技术、嵌入式系统及语音芯片技术于一体、结构紧凑、操作简单方便的盲人扑克游戏辅助仪。该装置设计了常见的扑克游戏程序,使用者可根据兴趣方便地选择游戏种类。其主要特点是利用语音技术能够实时播报其他人的出牌信息并可根据需要耳机播报本人手中牌的信息,让盲人用“听”牌代替了“摸”牌,使盲人以及不懂盲文的低视力人群能像正常人一样打扑克、玩桥牌等,克服了现有低视力群体打牌游戏中常见的问题,如盲文识别错误等。

  1. On Modified Bar recursion

    DEFF Research Database (Denmark)

    Oliva, Paulo Borges

    2002-01-01

    Modified bar recursion is a variant of Spector's bar recursion which can be used to give a realizability interpretation of the classical axiom of dependent choice. This realizability allows for the extraction of witnesses from proofs of forall-exists-formulas in classical analysis. In this talk I...... shall report on results regarding the relationship between modified and Spector's bar recursion. I shall also show that a seemingly weak form of modified bar recursion is as strong as "full" modified bar recursion in higher types....

  2. Observation of B0bar --> D0 K0bar and B0bar --> D0 K*0bar decays

    CERN Document Server

    Krokovnyi, P P

    2003-01-01

    We report on a search for B0bar --> D0 K(*)0bar decays based on 85 10^6 BBar events collected with the Belle detector at KEKB. The B0bar --> D0 K0bar and B0bar --> D0 K*0bar decays have been observed for the first time with the branching fractions Br(B0bar --> D0 K0bar) = (5.0^{+1.3}_{-1.2}+- 0.6) 10^{-5} and Br(B0bar --> D0 K*0bar) = (4.8^{+1.1}_{-1.0}+- 0.5) 10^{-5}. No significant signal has been found for the B0bar --> D*0 K(*)0bar and B0bar --> D(*)0bar K*0bar decay modes, and upper limits at 90% CL are presented.

  3. Computerized mega code recording.

    Science.gov (United States)

    Burt, T W; Bock, H C

    1988-04-01

    A system has been developed to facilitate recording of advanced cardiac life support mega code testing scenarios. By scanning a paper "keyboard" using a bar code wand attached to a portable microcomputer, the person assigned to record the scenario can easily generate an accurate, complete, timed, and typewritten record of the given situations and the obtained responses. PMID:3354937

  4. The four bars problem

    Science.gov (United States)

    Mauroy, Alexandre; Taslakian, Perouz; Langerman, Stefan; Jungers, Raphaël

    2016-09-01

    A four-bar linkage is a mechanism consisting of four rigid bars which are joined by their endpoints in a polygonal chain and which can rotate freely at the joints (or vertices). We assume that the linkage lies in the 2-dimensional plane so that one of the bars is held horizontally fixed. In this paper we consider the problem of reconfiguring a four-bar linkage using an operation called a pop. Given a four-bar linkage, a pop reflects a vertex across the line defined by its two adjacent vertices along the polygonal chain. Our main result shows that for certain conditions on the lengths of the bars, the neighborhood of any configuration that can be reached by smooth motion can also be reached by pops. The proof relies on the fact that pops are described by a map on the circle with an irrational number of rotation.

  5. QR code for medical information uses.

    Science.gov (United States)

    Fontelo, Paul; Liu, Fang; Ducut, Erick G

    2008-01-01

    We developed QR code online tools, simulated and tested QR code applications for medical information uses including scanning QR code labels, URLs and authentication. Our results show possible applications for QR code in medicine. PMID:18998785

  6. 应用UCC/EAN-128编码技术对转基因植物产品进行溯源研究%Tracing of genetically modified crops and their derived products by UCC/EAN-128 bar code

    Institute of Scientific and Technical Information of China (English)

    王醒宇; 杨捷琳; 陈勇; 潘良文; 丁卓平

    2013-01-01

    This paper gathered information from the five sections including the planting origin, products category, harvesting, processing and packaging stages. Based on the national standard and coding rules, the tracing of genetically modified crops by UCC/EAN-128 bar code about five sections was designed and encipher. As the example of soybeans, the five sections were combined to make the integrity the UCC/EAN bar code. The consumer can obtain the information and trace the products through scanning the UCC/EAN-128 bar code, combining with the data received and the data from the computer database.%该文对转基因植物产品从产地、产品、采收、加工、包装等5个环节收集信息,并根据国家标准中规定相应编码规则对这5个环节进行UCC/EAN-128码的设计与编码。最后,以大豆为例,将这5个编码结合,形成一个完整UCC/EAN-128码。消费者通过扫描条形码,获取相关数据,并将获得数据与计算机建立的数据库相结合,进行信息读取,了解转基因植物产品的生产、加工、包装等信息,从而对转基因植物产品进行有效的溯源。

  7. Design of Engineering Machinery Accessories of the Logistics Information System Based on Bar Code Technology%基于条形码的工程机械配件管理系统设计

    Institute of Scientific and Technical Information of China (English)

    江静岚; 谭桂芹

    2015-01-01

    Engineering machinery consists of thousands of spare parts and has a complicated list of accesso -ries.The characteristic of machinery manufacture is precision and just -in-time, which has strict acquirement in supply and distribution of accessories .Among the current management methods of accessories , many procedures still follow the traditional manual operating methods which are inefficient and easy to make mistakes .In order to es-tablish the standardized enterprise business processes of construction machinery and standardized basic data , and to enhance efficiency , the system, through the combination of the bar code technology and information processing technology , using the Thinkphp framework , which is based on the PHP language , as a system architecture , have designed and implemented a set of engineering machinery spare parts logistics information system based on barcode technology , ensuring the accuracy of the inventory , optimizing the punctuality of the storage management and deliv-ery of the inventory .And for the characteristic of uniqueness of the spare parts ’ code number , the retrospect and dynamic monitoring of every spare part is accomplished .%工程机械设备是由成千上万的配件组成,配件清单十分复杂,而机械制造生产的特点是精确化、准时化,对配件供应和配送要求十分严格。现行的配件管理方法中,许多步骤仍沿用传统的手工作业方式,效率低下,容易出错。为了更好地建立工程机械配件的标准化业务流程、标准化基础资料,提高效率,该系统通过条码技术与信息处理技术相结合,使用以PHP语言为基础的ThinkPHP框架作为系统架构,设计和实现了一套基于条码技术的机械配件物流信息系统,确保配件和产品库存数量的精确性,优化配件和产品在仓储管理和配送管理的准时性,并能利用配件条码编号的唯一性特点,实现每一个工程机械配件的追

  8. Bar-tailed

    NARCIS (Netherlands)

    Duijns, S.; Hidayati, N.A.; Piersma, T.

    2013-01-01

    Capsule Across the European wintering range Bar-tailed Godwits Limosa lapponica lapponica selected polychaete worms and especially Ragworms Hediste diversicolor, with differences between areas due to variations in prey availability.Aims To determine the diet of Bar-tailed Godwits across their winter

  9. BaBar Data Aquisition

    CERN Document Server

    Scott, I; Grosso, P; Hamilton, R T; Huffer, M E; O'Grady, C; Russell, J J

    1998-01-01

    The BaBar experiment at the Stanford Linear Accelerator Center is designed to perform a search for CP violation by analysing the decays of a very large sample of B and Bbar mesons produced at the high luminosity PEP-11 accelerator. The data acquisition system must cope with a sustained high event rate, while supporting real time feature extraction and data compression with minimal dead time. The BaBar data acquisition system is based around a common VME interface to the electronics read-out of the separate detector subsystems. Data from the front end electronics is read into commercial VME processors via a custom "personality card" and PCI interface. The commercial CPUs run the Tornado operating system to provide a platform for detector subsystem code to perform the necessary data processing. The data are read out via a non-blocking network switch to a farm of commercial UNIX processors. Careful design of the core data acquisition code has enabled us to sustain events rates in excess of 20 kHz while maintaini...

  10. A unique radioisotopic label as a new concept for safeguarding and tagging of long-term stored items and waste

    CERN Document Server

    Chernikova, Dina

    2013-01-01

    The present paper discuss a novel method of tagging and labeling of waste casks, copper canisters, spent fuel containers, mercury containers, waste pack- ages and other items. In particular, it is related to the development of new long-term security identification tags/labels that can be applied to articles for carrying information about the content, inventory tracking, prevention of falsifi- cation and theft etc. It is suggested to use a unique combination of radioisotopes with different predictable length of life, as a label of the items. The possibil- ity to realize a multidimensional bar code symbology is proposed as an option for a new labeling method. The results of the first tests and evaluations of this are shown and discussed in the paper. The invention is suitable for use in items assigned to long-term (hundreds of years) storing or for final repositories. Alternative field of use includes fresh nuclear fuel handling and shipment of goods.

  11. Changes in Smoking-Related Norms in Bars Resulting from California's Smoke-Free Workplace Act

    Science.gov (United States)

    Satterlund, Travis D.; Lee, Juliet P.; Moore, Roland S.

    2012-01-01

    California's Smoke-Free Workplace Act--CA Labor Code Sec. 6404.5(a)--was extended to bars in 1998. This article analyzes changes in normative beliefs and behaviors related to bar smoking in the decade following the adoption of the Act. In a series of studies evaluating the smoke-free workplace law in bars, researchers conducted extensive…

  12. Food Labels

    Science.gov (United States)

    ... How Can I Help a Friend Who Cuts? Food Labels KidsHealth > For Teens > Food Labels Print A ... have at least 95% organic ingredients. continue Making Food Labels Work for You The first step in ...

  13. Promote Legislation with Reformational Spirit for Problems of Code Labeling System%用改革的精神推动立法破解代码标识制度面临的难题

    Institute of Scientific and Technical Information of China (English)

    孟魁荣

    2014-01-01

    This paper reviews the history of the organization code labeling system, affirms the role of code system in actions of social governance and innovation including digitalization management and monitoring, e-government and business system construction, combating corruption and upholding integrity and the State Emergency Relief Command Decision, etc. It analyzes the differences and misunderstanding in the understanding and implementation of the State Council’s a series of important spiritual resolutions on code work, and proposes to implement the spirit of the Third Plenary Session, follow rules of market economy, promote legislation with the reformational spirit, reform top-level designed, as well as the specific suggestions of solution to solve the difficulties of code labeling.%本文回顾了我国组织机构代码标识制度的创建历史,肯定了代码系统在我国数字化管理与监督、电子政务与商务体系建设、反腐倡廉、国务院应急救灾指挥决策等社会治理创新中发挥了重要作用,分析了在理解和执行国务院关于代码工作的一系列重要决定精神方面出现了分歧和误区,提出了贯彻三中全会精神,遵循市场经济规律,用改革的精神推动立法,做好改革顶层设计,破解代码标识制度面临的难题的具体建议。

  14. Sports Season, Sports Bars

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ For foreigners in Beijing, the sports bar is a special place, a place to gather for watching matches and a place to feel the familiarity of home, while for some sports enthusiasts it serves as their second home.

  15. The bar instability revisited

    OpenAIRE

    Chiodi, Filippo; Andreotti, Bruno; Claudin, Philippe

    2012-01-01

    The river bar instability is revisited, using a hydrodynamical model based on Reynolds averaged Navier-Stokes equations. The results are contrasted with the standard analysis based on shallow water Saint-Venant equations. We first show that the stability of both transverse modes (ripples) and of small wavelength inclined modes (bars) predicted by the Saint-Venant approach are artefacts of this hydrodynamical approximation. When using a more reliable hydrodynamical model, the dispersion relati...

  16. Semi-supervised sparse coding

    KAUST Repository

    Wang, Jim Jing-Yan

    2014-07-06

    Sparse coding approximates the data sample as a sparse linear combination of some basic codewords and uses the sparse codes as new presentations. In this paper, we investigate learning discriminative sparse codes by sparse coding in a semi-supervised manner, where only a few training samples are labeled. By using the manifold structure spanned by the data set of both labeled and unlabeled samples and the constraints provided by the labels of the labeled samples, we learn the variable class labels for all the samples. Furthermore, to improve the discriminative ability of the learned sparse codes, we assume that the class labels could be predicted from the sparse codes directly using a linear classifier. By solving the codebook, sparse codes, class labels and classifier parameters simultaneously in a unified objective function, we develop a semi-supervised sparse coding algorithm. Experiments on two real-world pattern recognition problems demonstrate the advantage of the proposed methods over supervised sparse coding methods on partially labeled data sets.

  17. MetaBar - a tool for consistent contextual data acquisition and standards compliant submission

    Directory of Open Access Journals (Sweden)

    Kottmann Renzo

    2010-06-01

    Full Text Available Abstract Background Environmental sequence datasets are increasing at an exponential rate; however, the vast majority of them lack appropriate descriptors like sampling location, time and depth/altitude: generally referred to as metadata or contextual data. The consistent capture and structured submission of these data is crucial for integrated data analysis and ecosystems modeling. The application MetaBar has been developed, to support consistent contextual data acquisition. Results MetaBar is a spreadsheet and web-based software tool designed to assist users in the consistent acquisition, electronic storage, and submission of contextual data associated to their samples. A preconfigured Microsoft® Excel® spreadsheet is used to initiate structured contextual data storage in the field or laboratory. Each sample is given a unique identifier and at any stage the sheets can be uploaded to the MetaBar database server. To label samples, identifiers can be printed as barcodes. An intuitive web interface provides quick access to the contextual data in the MetaBar database as well as user and project management capabilities. Export functions facilitate contextual and sequence data submission to the International Nucleotide Sequence Database Collaboration (INSDC, comprising of the DNA DataBase of Japan (DDBJ, the European Molecular Biology Laboratory database (EMBL and GenBank. MetaBar requests and stores contextual data in compliance to the Genomic Standards Consortium specifications. The MetaBar open source code base for local installation is available under the GNU General Public License version 3 (GNU GPL3. Conclusion The MetaBar software supports the typical workflow from data acquisition and field-sampling to contextual data enriched sequence submission to an INSDC database. The integration with the megx.net marine Ecological Genomics database and portal facilitates georeferenced data integration and metadata-based comparisons of sampling sites as

  18. Raising the Bar (3)

    NARCIS (Netherlands)

    Elhorst, P.; Abreu, M.; Amaral, P.; Bhattacharjee, A.; Corrado, L.; Fingleton, B.; Fuerst, F.; Garretsen, H.; Igliori, D.; Le Gallo, J.; McCann, P.; Monastiriotis, V.; Pryce, G.; Yu, J.

    2016-01-01

    This editorial summarizes and comments on the papers published in issue 11(3) so as to raise the bar in applied spatial economic research and highlight new trends. The first paper proposes spatial and a-spatial indicators to describe the networks of airline companies around the world. The second pap

  19. The IPG BAR project

    NARCIS (Netherlands)

    Mentink, B.; Henriquez, L.; Van Niekerk, L.; Verheul, R.

    2013-01-01

    The booklets 'Making Patterns' and 'Using Patterns' describe two aspects of the the pattern method within the urban design process. The accompanying IPG BAR Pattern Library is a small pattern library of urban-airport symbiosis patterns. These documents are the result of the Interdisciplinary Projec

  20. Highest Oxygen Bar

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The world’s highest altitude Lhalu Wetland in Tibet is rebounding from past environmental damage In Lhasa, where the oxygen content is just 60 percent of that of the plain area, a place known as the "natural oxygen bar"is highly prized by residents.

  1. Raising the bar (2)

    NARCIS (Netherlands)

    Elhorst, P.; Abreu, M.; Amaral, P.; Bhattacharjee, A.; Corrado, L.; Fingleton, B.; Fuerst, F.; Garretsen, H.; Igliori, D.; Le Gallo, J.; McCann, P.; Monastiriotis, V.; Pryce, G.; Yu, J.

    2016-01-01

    In this editorial we summarise and comment on the papers published in issue 11.2 so as to raise the bar in applied spatial economic research and highlight new trends. The first paper analyses which regions in Europe were resilient to the great Recession and which ones were not. The second and the th

  2. The BaBar Data Acquisition System

    CERN Document Server

    Scott, I; Grosso, P; Huffer, M E; O'Grady, C; Russell, J J

    1999-01-01

    The BaBar experiment at the Stanford Linear Accelerator Center is designed to perform a search for CP violation by ana-lyzing the decays of a very large sample of B and B(Bar) mesons produced at the high luminosity PEP-II accelerator. The data acquisition system must cope with a sustained high event rate, while supporting real time feature extraction and data compression with minimal dead time. The BaBar data acquisition system is based around a common VME interface to the electronics read-out of the separate detec-tor subsystems. Data from the front end electronics is read into commercial VME processors via a custom "Personality Card" and PCI interface. The commercial CPUs run the Tornado operating system to provide a platform for detector subsystem code to perform the necessary data processing. The data is read out via a non-blocking network switch to a farm of commercial UNIX processors. The current implementation of the BaBar data acquisition sys-tem has been shown to sustain a Level 1 trigger rate of 1.3...

  3. Dark Matter Trapping by Stellar Bars: The Shadow Bar

    Science.gov (United States)

    Petersen, Michael S.; Weinberg, Martin D.; Katz, Neal

    2016-09-01

    We investigate the complex interactions between the stellar disc and the dark-matter halo during bar formation and evolution using N-body simulations with fine temporal resolution and optimally chosen spatial resolution. We find that the forming stellar bar traps dark matter in the vicinity of the stellar bar into bar-supporting orbits. We call this feature the shadow bar. The shadow bar modifies both the location and magnitude of the angular momentum transfer between the disc and dark matter halo and adds 10 per cent to the mass of the stellar bar over 4 Gyr. The shadow bar is potentially observable by its density and velocity signature in spheroid stars and by direct dark matter detection experiments. Numerical tests demonstrate that the shadow bar can diminish the rate of angular momentum transport from the bar to the dark matter halo by more than a factor of three over the rate predicted by dynamical friction with an untrapped dark halo, and thus provides a possible physical explanation for the observed prevalence of fast bars in nature.

  4. Dark Matter Trapping by Stellar Bars: The Shadow Bar

    CERN Document Server

    Petersen, Michael S; Katz, Neal

    2016-01-01

    We investigate the complex interactions between the stellar disc and the dark-matter halo during bar formation and evolution using N-body simulations with fine temporal resolution and optimally chosen spatial resolution. We find that the forming stellar bar traps dark matter in the vicinity of the stellar bar into bar-supporting orbits. We call this feature the shadow bar. The shadow bar modifies both the location and magnitude of the angular momentum transfer between the disc and dark matter halo and adds 10 per cent to the mass of the stellar bar over 4 Gyr. The shadow bar is potentially observable by its density and velocity signature in spheroid stars and by direct dark matter detection experiments. Numerical tests demonstrate that the shadow bar can diminish the rate of angular momentum transport from the bar to the dark matter halo by more than a factor of three over the naive dynamical friction prediction, and thus provides a possible physical explanation for the observed prevalence of fast bars in nat...

  5. Cooling of rectangular bars

    International Nuclear Information System (INIS)

    A solution of the time-transient Heat Transfer Differential Equation in rectangular coordinates is presented, leading to a model which describes the temperature drop with time in rectangular bars. It is similar to an other model for cilindrical bars which has been previously developed in the Laboratory of Mechanical Metallurgy of UFRGS. Following these models, a generalization has been made, which permits cooling time evaluation for all profiles. These results are compared with experimental laboratory data in the 1200 to 8000C range. Some other existing models were also studied which have the purpose of studing the same phenomenon. Their mathematical forms and their evaluated values are analyzed and compared with experimental ones. (Author)

  6. The bar instability revisited

    CERN Document Server

    Chiodi, Filippo; Claudin, Philippe

    2012-01-01

    The river bar instability is revisited, using a hydrodynamical model based on Reynolds averaged Navier-Stokes equations. The results are contrasted with the standard analysis based on shallow water Saint-Venant equations. We first show that the stability of both transverse modes (ripples) and of small wavelength inclined modes (bars) predicted by the Saint-Venant approach are artefacts of this hydrodynamical approximation. When using a more reliable hydrodynamical model, the dispersion relation does not present any maximum of the growth rate when the sediment transport is assumed to be locally saturated. The analysis therefore reveals the fundamental importance of the relaxation of sediment transport towards equilibrium as it it is responsible for the stabilisation of small wavelength modes. This dynamical mechanism is characterised by the saturation number, defined as the ratio of the saturation length to the water depth Lsat/H. This dimensionless number controls the transition from ripples (transverse patte...

  7. Breaking through the Bar

    Science.gov (United States)

    Gray, Katti

    2011-01-01

    Howard University School of Law had a problem, and school officials knew it. Over a 20-year period, 40 percent of its graduates who took the Maryland bar exam failed it on their first try. During the next 24 months--the time frame required to determine its "eventual pass rate"--almost 90 percent of the students did pass. What they did not know was…

  8. Applying Schwarzschild's orbit superposition method to barred or non-barred disc galaxies

    CERN Document Server

    Vasiliev, Eugene

    2015-01-01

    We present an implementation of the Schwarzschild orbit superposition method which can be used for constructing self-consistent equilibrium models of barred or non-barred disc galaxies, or of elliptical galaxies with figure rotation. This is a further development of the publicly available code SMILE; its main improvements include a new efficient representation of an arbitrary gravitational potential using two-dimensional spline interpolation of Fourier coefficients in the meridional plane, as well as the ability to deal with rotation of the density profile and with multicomponent mass models. We compare several published methods for constructing composite axisymmetric disc--bulge--halo models and demonstrate that our code produces the models that are closest to equilibrium. We also apply it to create models of triaxial elliptical galaxies with cuspy density profiles and figure rotation, and find that such models can be found and are stable over many dynamical times in a wide range of pattern speeds and angula...

  9. Nutrition Labeling

    DEFF Research Database (Denmark)

    Grunert, Klaus G

    2013-01-01

    because consumers will avoid products that the label shows to be nutritionally deficient, but also because food producers will try to avoid marketing products that appear, according to the label, as nutritionally problematic, for example, because of a high content of saturated fat or salt. Nutrition......Nutrition labeling refers to the provision of information on a food product’s nutritional content on the package label. It can serve both public health and commercial purposes. From a public health perspective, the aim of nutrition labeling is to provide information that can enable consumers...... to make healthier choices when choosing food products. Nutrition labeling is thus closely linked to the notion of the informed consumer, that chooses products according to their aims, on the basis of the information at their disposal. Because many consumers are assumed to be interested in making healthy...

  10. Observations of offshore bar decay

    DEFF Research Database (Denmark)

    Aagaard, Troels; Kroon, Aart; Greenwood, Brian;

    2010-01-01

    Long-term, net offshore bar migration is a common occurrence on many multiple-barred beaches. The first stage of the process involves the generation of a longshore bar close to the shoreline that oscillates about a mean position for some time, followed by a stage of net offshore migration across...... the upper shoreface, and finally a stage of decaying bar form through loss of sediment volume at the outer boundary of the upper shoreface. The phenomenon has been previously documented in the Netherlands, the USA, the Canadian Great Lakes, and in New Zealand, but our present understanding...... of the morphodynamic processes and sediment transport pathways involved in bar decay is limited. In this paper, long-term, net offshore bar migration is investigated at Vejers Beach, located on the North Sea coast of Denmark where offshore bar migration rates are of the order of 45–55 m a-1. A wave height...

  11. Bar Code Reader”とdBASE III PLUSとをインターフェースするプログラムの作成

    OpenAIRE

    比留木, 武雄

    1994-01-01

    The author reported Canine Dirofilariasis Control (CDC) Programs in dBASE III Ver. 2.0 (dBASE) which can control periodical administration of drugs, and forward a direct mail (DM) such an drugs and/or letter to the breeder. Although expected to be available in a pet clinic, these CDC programs proved to be still room for improvement because the voice has been heard that typing data manually is a durden, especially during a busy clinical work. Thus, the author decided to utilize a her code read...

  12. Making food labels social: The impact of colour of nutritional labels and injunctive norms on perceptions and choice of snack foods.

    Science.gov (United States)

    Vasiljevic, Milica; Pechey, Rachel; Marteau, Theresa M

    2015-08-01

    Recent studies report that using green labels to denote healthier foods, and red to denote less healthy foods increases consumption of green- and decreases consumption of red-labelled foods. Other symbols (e.g. emoticons conveying normative approval and disapproval) could also be used to signal the healthiness and/or acceptability of consuming such products. The present study tested the combined effects of using emoticons and colours on labels amongst a nationally representative sample of the UK population (n = 955). In a 3 (emoticon expression: smiling vs. frowning vs. no emoticon) × 3 (colour label: green vs. red vs. white) ×2 (food option: chocolate bar vs. cereal bar) between-subjects experiment, participants rated the level of desirability, healthiness, tastiness, and calorific content of a snack bar they had been randomised to view. At the end they were further randomised to view one of nine possible combinations of colour and emoticon labels and asked to choose between a chocolate and a cereal bar. Regardless of label, participants rated the chocolate as tastier and more desirable when compared to the cereal bar, and the cereal bar as healthier than the chocolate bar. A series of interactions revealed that a frowning emoticon on a white background decreased perceptions of healthiness and tastiness of the cereal bar, but not the chocolate bar. In the explicit choice task selection was unaffected by label. Overall nutritional labels had limited effects on perceptions and no effects on choice of snack foods. Emoticon labels yielded stronger effects on perceptions of taste and healthiness of snacks than colour labels. Frowning emoticons may be more potent than smiling emoticons at influencing the perceived healthiness and tastiness of foods carrying health halos.

  13. Obtention control bars patterns for a BWR using Tabo search

    International Nuclear Information System (INIS)

    The obtained results when implementing the technique of tabu search, for to optimize patterns of control bars in a BWR type reactor, using the CM-PRESTO code are presented. The patterns of control bars were obtained for the designs of fuel reloads obtained in a previous work, using the same technique. The obtained results correspond to a cycle of 18 months using 112 fresh fuels enriched at the 3.53 of U-235. The used technique of tabu search, prohibits recently visited movements, in the position that correspond to the axial positions of the control bars, additionally the tiempotabu matrix is used for to manage a size of variable tabu list and the objective function is punished with the frequency of the forbidden movements. The obtained patterns of control bars improve the longitude of the cycle with regard to the reference values and they complete the restrictions of safety. (Author)

  14. 基于码流误差掩盖补偿的同态标签关联编码设计%Design of Homomorphic Label Association Code Based on Error Stream Concealment Compensation

    Institute of Scientific and Technical Information of China (English)

    陈虹

    2015-01-01

    物联网环境下采用GPU多处理器集群进行数据加密和存储,同态标签关联编码是保证存储系统容错过程中数据的安全性的关键。提出一种基于码流误差掩盖补偿的物联网下GPU多处理器集群的同态标签关联编码方法,构建物联网下的GPU多处理器集群通信系统模型,把物联网下GPU多处理器集群通信系统的同态标签关联编码方案分为节点集合、规则、支持度和置信度4个元素,采用特征关联对参量模型进行系统描述,把生存时间最大化问题变成了一个线性规划问题。采用基于码流误差掩盖补偿进行同态标签关联编码改进。实验结果表明,采用该算法,物联网通信系网络生存时间增益提高,编码性能较好,收敛性好,迭代次数较少,生存时间性能增益和计算开销都较传统方法优越,展示了算法的优越性能,有效保证了物联网通信安全。%Data encryption and storage uses GPU multi processor cluster in networking environment, homomorphic tag fault-tolerant coding is the key to guarantee the data storage system fault tolerant process safety. The homomorphism label coding a cover up stream error compensation based on the Internet of things GPU multi processor cluster, multi processor cluster communication system model of Internet of things of GPU is constructed, the homomorphism tag fault-tolerant cod⁃ing GPU multiprocessor cluster communication system network case is divided into 4 elements as node set, rules, support degree and confidence, the system description of the parametric model feature correlation is obtained, the maximum surviv⁃al time is converted into a linear programming problem. The stream error concealment compensation homomorphic label coding is improved. The experimental results show that this algorithm is applied in network communication system network, the survival time gain is improved, it has better coding performance and good

  15. Ukola Club. Bar americano

    Directory of Open Access Journals (Sweden)

    Azpiazu, J. R.

    1961-03-01

    Full Text Available En la calle de Serrano, aprovechando un semisótano dedicado a otro negocio anteriormente, se ha instalado un bar americano, de cuyo interior ofrecemos algunos pormenores. Se han cuidado, especialmente, las condiciones acústicas, resueltas por medio de un techo de escayola perforada, con vitrofib en su parte superior, y paredes de madera, que contribuyen a darle un ambiente cálido y acogedor. El soporte de hierro laminado existente en el centro del local, cuya supresión hubiera sido costosa, se ha revestido con lajas de mármol que le convierten en un elemento decorativo.

  16. The decays \\bar{B}->\\bar{K}D and \\bar{B}-> \\bar{K}\\bar{D} and final state interactions

    CERN Document Server

    Fayyazuddin, A

    2001-01-01

    The decays \\bar{B}-> \\bar{K}D and \\bar{B}-> \\bar{K}\\bar{D} taking into account final state interactions are discussed. These decays are described by four strong phases \\delta_0,\\delta_1,\\bar{\\delta}_0,\\bar{\\delta}_1 (subscripts 0 and 1 refers to I=0 and I=1 final states), one weak phase \\gamma and four real amplitudes. It is argued that strong interaction dynamics implies \\bar{\\delta}_1=0,\\delta_0=-\\delta_1. Rescattering has significant effects on weak amplitudes. Taking into account, rescattering, we find that direct CP--violating asymmetry in these decays may lie in the range \\mp 0.023\\sin \\gamma \\leq \\QTR{cal}{A}_{1,2}\\leq \\mp 0.086\\sin \\gamma.

  17. 基于nCode的前横向稳定杆应变疲劳分析%Strain Fatigue Analysis on Front Transverse Stability Bar Based on nCode

    Institute of Scientific and Technical Information of China (English)

    倪昀; 陈伟

    2014-01-01

    基于应变疲劳相关理论,采用Hypermesh软件建立了汽车前横向稳定杆的FEM模型,按照实际的跳动行程与约束条件,利用Nastran进行静态力学求解,然后将求解结果在nCode DesignLife中做E-N仿真分析.获得预测该零件的应变疲劳寿命、寿命安全系数及断裂危险位置等信息,验证了零件设计的合理性,同时为零件优化设计及材料的选择提供了科学设计依据.

  18. Bar piezoelectric ceramic transformers.

    Science.gov (United States)

    Erhart, Jiří; Pulpan, Půlpán; Rusin, Luboš

    2013-07-01

    Bar-shaped piezoelectric ceramic transformers (PTs) working in the longitudinal vibration mode (k31 mode) were studied. Two types of the transformer were designed--one with the electrode divided into two segments of different length, and one with the electrodes divided into three symmetrical segments. Parameters of studied transformers such as efficiency, transformation ratio, and input and output impedances were measured. An analytical model was developed for PT parameter calculation for both two- and three-segment PTs. Neither type of bar PT exhibited very high efficiency (maximum 72% for three-segment PT design) at a relatively high transformation ratio (it is 4 for two-segment PT and 2 for three-segment PT at the fundamental resonance mode). The optimum resistive loads were 20 and 10 kΩ for two- and three-segment PT designs for the fundamental resonance, respectively, and about one order of magnitude smaller for the higher overtone (i.e., 2 kΩ and 500 Ω, respectively). The no-load transformation ratio was less than 27 (maximum for two-segment electrode PT design). The optimum input electrode aspect ratios (0.48 for three-segment PT and 0.63 for two-segment PT) were calculated numerically under no-load conditions.

  19. Dynamical Evolution of Barred Galaxies

    OpenAIRE

    Athanassoula, E

    2005-01-01

    Angular momentum redistribution within barred galaxies drives their dynamical evolution. Angular momentum is emitted mainly by near-resonant material in the bar region and absorbed by resonant material mainly in the outer disc and in the halo. This exchange determines the strength of the bar, the decrease of its pattern speed, as well as its morphology. If the galaxy has also a gaseous component and/or a companion or satellite, then these also take part in the angular momentum exchange. Durin...

  20. Just the ticket [ANDRA barcode labelling for French LLW packages

    Energy Technology Data Exchange (ETDEWEB)

    Sueur, P.; Forest, I. (ANDRA, DSQC/EIA, Fontenay aux Roses (France))

    1992-09-01

    ANDRA, the national radioactive waste management agency of France, uses bar codes to identify waste packages and track their movements. The bar codes are used to manage waste intended for near-surface disposal. This type of waste is received from several generators -Electricite de France, Cogema, Commissariate l'Energie Atomique and other companies and research laboratories - and the bar codes have had to be integrated with the Agency's previous process, which had three steps: waste acceptance, product quality and waste shipment. (Author).

  1. Just the ticket [ANDRA barcode labelling for French LLW packages

    International Nuclear Information System (INIS)

    ANDRA, the national radioactive waste management agency of France, uses bar codes to identify waste packages and track their movements. The bar codes are used to manage waste intended for near-surface disposal. This type of waste is received from several generators -Electricite de France, Cogema, Commissariate l'Energie Atomique and other companies and research laboratories - and the bar codes have had to be integrated with the Agency's previous process, which had three steps: waste acceptance, product quality and waste shipment. (Author)

  2. 46 CFR Appendix A to Part 520 - Standard Terminology and Codes

    Science.gov (United States)

    2010-10-01

    ... CLD Frozen FRZ Heated HTD Refrigerated RE Ventilated VEN J. Packaging Codes: Bag BAG Bale BAL Bar BAR... Reverse Reel RVR Sack SAK Shook SHK Sides of Beef SID Skid SKD Skid, Elev, Lift Trk SKE Sleeve SLV...

  3. 基于条形码识别的物流包裹自动分拣系统设计%Design of Automatic Parcel Sorting System Based on Bar Code Recognition

    Institute of Scientific and Technical Information of China (English)

    王昆; 刘晓山

    2016-01-01

    为了提高物流中心对快递包裹的分拣效率,在档板式分拣机的基础上设计了自动控制系统,该系统由智能终端和计算机信息系统两部分组成,采用 C/S 架构设计。智能终端作为客户端在 DSP 处理器TMS320DM6437平台上开发,采用红外感应器检测包裹的位置,然后触发摄像头采集包裹上运单的图像,经过处理后译出运单号码,再通过与计算机信息系统建立的TCP/IP连接进行数据通信,查询包裹的目的地,并返回给智能终端后对分离机械手进行控制,从而达到自动分拣的目的。通过测试结果表明,该系统能够自动识别出顺丰快递Code128C编码的运单号码,并通过对分离旋转挡臂的控制实现了自动分拣,大大提高了快递行业的工作效率。%In order to improve the efficiency on the express parcel sorting, automatic control system, designed with C/S architecture is proposed, which is based on the baffle plate sorting machine and composed of intelligent terminals and computer information system. As a client, the intelligent terminal, developed on the platform of TMS320DM6437, detects the position of parcel with infrared inductor and triggers the camera to collect the image on package. The intelligent terminal achieves date communication with the information sys-tem by establishing TCP /IP connection after way bill number is decoded, then the package destination inquires are settled and informa-tion is fed back to intelligent terminal for sorting by controlling the separating machine. The test results show that the system can auto-matically identify the SF express number with Code128C and sort parcels by controlling the rotating baffle arm. It greatly improves effi-ciency of the express delivery industry.

  4. Food labeling

    Science.gov (United States)

    ... per serving to the right of the nutrient. Vitamins and minerals: Only two vitamins (A and C) and two ... are required on the food label. But, when vitamins or minerals are added to the food, or when a ...

  5. 基于二维码识别技术的电子签到模块设计%The Modern Check-in System Based on Two-Dimensional Bar Code

    Institute of Scientific and Technical Information of China (English)

    李立峰

    2012-01-01

    With the continuous development of the socio-economic information network technology,people increasingly rely on mobile Internet,and have much higher requirements for the mobile experience; on the other hand,another part of consumption - the merchant is also gradually looking for more innovative and efficient means to demonstrate their products and services to increase revenue. In such circumstances,the sign business model appears on the scene,people can go to merchant stores to check-in and get more promotions with handheld devices. In order to solve the consumer to sign the accurate location positioning,two-dimensional code recognition technology is used to provide a real and effective sign experience.%随着社会经济与信息网络技术的不断发展,人们对移动互联网越来越依赖,对移动体验的要求也越来越高;另一方面消费的另一环节-商户也渐渐地在寻找更加新颖快捷的技术手段来表现他们的产品及服务以增加收入.在这样的环境下,签到商业模式应运而生,人们可以通过手持设备向某地的商户门店进行签到进行互动.为了解决消费者签到位置定位不准确的问题,采取了二维码识别技术来为商家和消费者提供真实有效的签到体验.

  6. Dynamical Evolution of Barred Galaxies

    CERN Document Server

    Athanassoula, E

    2005-01-01

    Angular momentum redistribution within barred galaxies drives their dynamical evolution. Angular momentum is emitted mainly by near-resonant material in the bar region and absorbed by resonant material mainly in the outer disc and in the halo. This exchange determines the strength of the bar, the decrease of its pattern speed, as well as its morphology. If the galaxy has also a gaseous component and/or a companion or satellite, then these also take part in the angular momentum exchange. During the evolution a bar structure forms in the inner parts of the halo as well. This bar is shorter and fatter than the disc bar and stays so all through the simulation, although its length grows considerably with time. Viewed edge-on, the bar in the disc component acquires a boxy or peanut shape. I describe the families of periodic orbits that explain such structures and review the observations showing that boxy/peanut `bulges' are in fact just bars seen edge-on.

  7. Niobium in engineering bar steels

    International Nuclear Information System (INIS)

    The use of niobium as a microalloying addition to hot rolled and cold finished bars offers many opportunities to achieve enhanced mechanical properties in a very cost effective manner. By the addition of niobium (sometimes in combination with vanadium) to selected carbon steel grades, it is possible to produce hot rolled bars with minimum yield strengths up to 689 MPa (100 ksi) and cold finished bars with yield strengths up to 1035 MPa (150 ksi). These high-strength-low-alloy bars have a myriad of applications particularly for automotive parts such as shafts, stabilizer bars, tie rods, piston rods, fasteners such as U-bolts, brackets, and various transmission parts. Of particular value has been the specification of Nb-microalloyed steels for such hot forgings as connecting rods and caps, and weld yokes a situation which has permitted elimination of post-forging heat treatment (quenching and tempering). Significant reductions in cost and energy consumption have been realized

  8. Bars in Cuspy Dark Halos

    CERN Document Server

    Dubinski, John; Shlosman, Isaac

    2008-01-01

    We examine the bar instability in models with an exponential disk and a cuspy NFW-like dark matter (DM) halo inspired by cosmological simulations. Bar evolution is studied as a function of numerical resolution in a sequence of models spanning 10K to 100M DM particles - including a multi-mass model with an effective resolution of 10G. The goal is to find convergence in dynamical behaviour. We characterize the bar growth, the buckling instability, pattern speed decay through resonant transfer of angular momentum, and possible destruction of the DM halo cusp. Overall, most characteristics converge in behaviour in detail for halos containing more than 10M particles. Notably, the formation of the bar does not destroy the density cusp in this case. These higher resolution simulations clearly illustrate the importance of discrete resonances in transporting angular momentum from the bar to the halo.

  9. Galaxy Zoo: CANDELS Barred Disks and Bar Fractions

    CERN Document Server

    Simmons, B D; Lintott, Chris; Masters, Karen L; Willett, Kyle W; Keel, William C; Smethurst, R J; Cheung, Edmond; Nichol, Robert C; Schawinski, Kevin; Rutkowski, Michael; Kartaltepe, Jeyhan S; Bell, Eric F; Casteels, Kevin R V; Conselice, Christopher J; Almaini, Omar; Ferguson, Henry C; Fortson, Lucy; Hartley, William; Kocevski, Dale; Koekemoer, Anton M; McIntosh, Daniel H; Mortlock, Alice; Newman, Jeffrey A; Ownsworth, Jamie; Bamford, Steven; Dahlen, Tomas; Faber, Sandra M; Finkelstein, Steven L; Fontana, Adriano; Galametz, Audrey; Grogin, N A; Grutzbauch, Ruth; Guo, Yicheng; Haussler, Boris; Jek, Kian J; Kaviraj, Sugata; Lucas, Ray A; Peth, Michael; Salvato, Mara; Wiklind, Tommy; Wuyts, Stijn

    2014-01-01

    The formation of bars in disk galaxies is a tracer of the dynamical maturity of the population. Previous studies have found that the incidence of bars in disks decreases from the local Universe to z ~ 1, and by z > 1 simulations predict that bar features in dynamically mature disks should be extremely rare. Here we report the discovery of strong barred structures in massive disk galaxies at z ~ 1.5 in deep rest-frame optical images from CANDELS. From within a sample of 876 disk galaxies identified by visual classification in Galaxy Zoo, we identify 123 barred galaxies. Selecting a sub-sample within the same region of the evolving galaxy luminosity function (brighter than L*), we find that the bar fraction across the redshift range 0.5< z < 2 (f_bar = 10.7 +6.3 -3.5% after correcting for incompleteness) does not significantly evolve. We discuss the implications of this discovery in the context of existing simulations and our current understanding of the way disk galaxies have evolved over the last 11 bil...

  10. Design and implementation of food safety backtracking system based on two-dimensional bar code of PDF417%基于PDF417二维条码的食品安全追溯系统的设计与实现

    Institute of Scientific and Technical Information of China (English)

    李建春; 张江伟; 谢小丽; 李健勇; 黄道颖

    2011-01-01

    Because the current situation of the frequent occurrence of food security events, PDF417 two-dimensional bar code encoding and decoding components were designed and implemented based on COM technology, and applied to the food safety backtracking system. Through effective monitoring of the life cycle of problems food, they can be traced quickly, and the source can be found and the fast positioning of the flow of food can be achieved.%针对当前食品安全事件频发的情况,设计和实现了基于COM技术的PDF417二维条码编解码组件,并将其应用到食品安全回溯系统中,通过对食品生命周期的有效监控,对问题食品进行回溯,迅速实现问题食品源头和流向的快速定位.

  11. Repairing and strengthening a fractured Hader bar.

    Science.gov (United States)

    Herrero, D B

    1997-01-01

    Stresses from occlusion and metal fatigue over time can cause fracture of overdenture retention bars. Often failure of the bar necessitates the removal and remake of the bar. This may damage the abutment, especially if there are dowel posts involved. This article describes a method for reinforcing the existing bar without having to remove the bar or significantly alter the overdenture. The fractured bar can be prepared in the mouth to receive a reinforcing superstructure that will be cemented.

  12. Decoding Different Patterns in Various Grey Tones Incorporated in the QR Code

    OpenAIRE

    Filip Cvitić; Jesenka Pibernik

    2014-01-01

    Using colors in bar codes causes errors that may adversely affect their readability (Tan etal. 2010), given that the contrast between data and background modules is reduced. Due to the unreliability of using color bar codes, most designers still keep to the limitations placed by Pira International (Smithers Pira) in 2002 (Williams, 2004). Since the contrast between data modules and background modules is the most important aspect in the process of reliable bar code decoding, this paper explore...

  13. Triply heavy tetraquark states with the $QQ\\bar{Q}\\bar{q}$ configuration

    CERN Document Server

    Chen, Kan; Wu, Jing; Liu, Yan-Rui; Zhu, Shi-Lin

    2016-01-01

    In the framework of the color-magnetic interaction, we systematically investigate the mass splittings of the $QQ\\bar{Q}\\bar{q}$ tetraquark states and estimated their rough masses in this work. These systems include the explicitly exotic states $cc\\bar{b}\\bar{q}$ and $bb\\bar{c}\\bar{q}$ and the hidden exotic states $cc\\bar{c}\\bar{q}$, $cb\\bar{b}\\bar{q}$, $bc\\bar{c}\\bar{q}$, and $bb\\bar{b}\\bar{q}$. If a state around the estimated mass region could be observed, its nature as a genuine tetraquark is favored. The strong decay patterns shown here will be helpful to the experimental search for these exotic states.

  14. Strength Degradation of Gfrp Bars

    OpenAIRE

    Bhise, Vikrant Sudhakar

    2002-01-01

    The primary objective of this research was to examine the strength degradation of Glass Fiber Reinforced Polymer (GFRP) bars at high temperature and alkalinity and determine if an Arrhenius type relationship can be used as a means of projecting life. The work done includes a thorough literature review, experiments and development of strength prediction models. The experimental work involves exposure of GFRP bars incased in cement mortar to lime-water solution at 30, 45 and 57°C. Overall 100 ...

  15. Multiprobe quantum spin Hall bars

    OpenAIRE

    Sanvito, Stefano

    2013-01-01

    PUBLISHED We analyze electron transport in multiprobe quantum spin Hall (QSH) bars using the B¨uttiker formalism and draw parallels with their quantum Hall (QH) counterparts. We find that in a QSH bar the measured resistance changes upon introducing side voltage probes, in contrast to the QH case. We also study four- and six-terminal geometries and derive the expressions for the resistances. For these our analysis is generalized from the single-channel to the multi-channel case...

  16. Nanoporosity of Si (100) bars

    Science.gov (United States)

    Novikov, S. N.; Timoshenkov, S. P.; Minaev, V. S.; Goryunova, E. P.; Gerasimenko, N. N.; Smirnov, D. I.

    2016-09-01

    Si(100) samples cut from a typical bar (100 mm in diameter) prepared using industrial technology are studied. Measurements of the electron work function (EWF) show that the size effects in these samples (a reduction in thickness along with a sample's area and the EWF) detected earlier were due to nanostructure porosity that was buried by the technological treatment of a bar's surface. This hidden nanoporosity is assumed to be a manifestation of the secondary crystal structure.

  17. Barred disks in dense environments

    CERN Document Server

    Marinova, I; Heiderman, A; Barazza, F D; Gray, M E; Barden, M; Wolf, C; Peng, C Y; Bacon, D; Balogh, M; Bell, E F; Bohm, A; Caldwell, J A R; Haussler, B; Heymans, C; Jahnke, K; van Kampen, E; Koposov, S; Lane, K; McIntosh, D H; Meisenheimer, K; Rix, H -W; Sanchez, S F; Taylor, A; Wisotzki, L; Zheng, X

    2010-01-01

    We investigate the properties of bright (MV <= -18) barred and unbarred disks in the Abell 901/902 cluster system at z~0.165 with the STAGES HST ACS survey. To identify and characterize bars, we use ellipse-fitting. We use visual classification, a Sersic cut, and a color cut to select disk galaxies, and find that the latter two methods miss 31% and 51%, respectively of disk galaxies identified through visual classification. This underscores the importance of carefully selecting the disk sample in cluster environments. However, we find that the global optical bar fraction in the clusters is ~30% regardless of the method of disk selection. We study the relationship of the optical bar fraction to host galaxy properties, and find that the optical bar fraction depends strongly on the luminosity of the galaxy and whether it hosts a prominent bulge or is bulgeless. Within a given absolute magnitude bin, the optical bar fraction increases for galaxies with no significant bulge component. Within each morphological ...

  18. Food labels

    DEFF Research Database (Denmark)

    Selsøe Sørensen, Henrik; Clement, Jesper; Gabrielsen, Gorm

    2012-01-01

    The food industry develops tasty and healthy food but fails to deliver the message to all consumers. The consumers’ background knowledge is essential for how they find and decode relevant elements in the cocktail of signs which fight for attention on food labels. In this exploratory study, we find...... evidence for dividing consumers into two profiles: one relying on general food knowledge and another using knowledge related to signpost labels. In a combined eyetracking and questionnaire survey we analyse the influence of background knowledge and identify different patterns of visual attention...... for the two consumer profiles. This underlines the complexity in choosing and designing the ‘right’ elements for a food package that consumers actually look at and are able to make rational use of. In spite of any regulation of food information provided by authorities, consumers will still be confronted...

  19. Field observations of nearshore bar formation

    DEFF Research Database (Denmark)

    Aagaard, Troels; Kroon, Aart; Greenwood, Brian;

    2008-01-01

      The formation of an inner nearshore bar was observed during a high-energy event at the sandy beach of Vejers, Denmark. The bar accreted in situ during surf zone conditions and the growth of the bar was associated with the development of a trough landward of the bar. Measurements of hydrodynamics...

  20. /bar p/p collider physics

    Energy Technology Data Exchange (ETDEWEB)

    Green, D.

    1989-03-01

    This note encompasses a set of six lectures given at the summer school held at Campos Do Jordao in January of 1989 near Sao Paulo, Brazil. The intent of the lectures was to describe the physics of /bar p/p at CERN and Fermilab. Particular attention has been paid to making a self contained presentation to a prospective audience of graduate students. Since large Monte Carlo codes might not be available to all members of this audience, great reliance was placed on ''back of the envelope estimates.'' Emphasis was also placed on experimental data rather than theoretical speculation, since predictions for, for example, supersymmetric particle production are easily obtained by transcription of formulae already obtained. 9 refs., 67 figs., 2 tabs.

  1. Gas flow in barred potentials II. Bar Driven Spiral Arms

    CERN Document Server

    Sormani, Mattia C; Magorrian, John

    2015-01-01

    Spiral arms that emerge from the ends of a galactic bar are important in interpreting observations of our and external galaxies. It is therefore important to understand the physical mechanism that causes them. We find that these spiral arms can be understood as kinematic density waves generated by librations around underlying ballistic closed orbits. This is even true in the case of a strong bar, provided the librations are around the appropriate closed orbits and not around the circular orbits that form the basis of the epicycle approximation. An important consequence is that it is a potential's orbital structure that determines whether a bar should be classified as weak or strong, and not crude estimates of the potential's deviation from axisymmetry.

  2. The BaBar Electromagnetic Calorimeter: Status and Performance Improvements

    OpenAIRE

    Bauer, Johannes M.; Group, for the BaBar Collaboration EMC

    2006-01-01

    The electromagnetic calorimeter at the BaBar detector, part of the asymmetric B Factory at SLAC, measures photons in the energy range from 20 MeV to 8 GeV with high resolution. The current status of the calorimeter, now in its seventh year of operation, is being presented, as well as details on improvements made to the analysis code during the last years.

  3. GFRP Bar: Determining Tensile Strength with Bending Test

    OpenAIRE

    Almerich Chulia, Ana Isabel; Fenollosa Forner, Ernesto Jesús; Cabrera Fausto, Ivan

    2015-01-01

    In order to obtain GFRP reinforcement bars it is necessary to undertake tests regulated code which require important mechanical tools. This paper presents a method which allows for determining GFRP rebars tensile strength value from their flexural strength value which has been obtained with a simple, inexpensive and reliable test. This method results will be verified by applying it to values obtained in a series of bending tests and comparing these results with values obtained in tensile test...

  4. Population coding of somatic sensations

    Institute of Scientific and Technical Information of China (English)

    Qiufu Ma

    2012-01-01

    The somatic sensory system includes a variety of sensory modalities,such as touch,pain,itch,and temperature sensitivity.The coding of these modalities appears to be best explained by the population-coding theory,which is composed of the following features.First,an individual somatic sensory afferent is connected with a specific neural circuit or network (for simplicity,a sensory-labeled line),whose isolated activation is sufficient to generate one specific sensation under normal conditions.Second,labeled lines are interconnected through local excitatory and inhibitory interneurons.As a result,activation of one labeled line could modulate,or provide gate control of,another labeled line.Third,most sensory fibers are polymodal,such that a given stimulus placed onto the skin often activates two or multiple sensory-labeled lines;crosstalk among them is needed to generate one dominant sensation.Fourth and under pathological conditions,a disruption of the antagonistic interaction among labeled lines could open normally masked neuronal pathways,and allow a given sensory stimulus to evoke a new sensation,such as pain evoked by innocuous mechanical or thermal stimuli and itch evoked by painful stimuli.As a result of this,some sensory fibers operate along distinct labeled lines under normal versus pathological conditions.Thus,a better understanding of the neural network underlying labeled line crosstalk may provide new strategies to treat chronic pain and itch.

  5. Measurement of B0bar -> D(*)0 K(*)0bar Branching Fractions

    CERN Document Server

    Aubert, B; Boutigny, D; Couderc, F; Karyotakis, Yu; Lees, J P; Poireau, V; Tisserand, V; Zghiche, A; Graugès-Pous, E; Palano, A; Pappagallo, M; Chen, J C; Qi, N D; Rong, G; Wang, P; Zhu, Y S; Eigen, G; Ofte, I; Stugu, B; Abrams, G S; Battaglia, M; Best, D S; Brown, D N; Button-Shafer, J; Cahn, R N; Charles, E; Day, C T; Gill, M S; Gritsan, A V; Groysman, Y; Jacobsen, R G; Kadyk, J A; Kerth, L T; Kolomensky, Yu G; Kukartsev, G; Lynch, G; Mir, L M; Oddone, P J; Orimoto, T J; Pripstein, M; Roe, N A; Ronan, M T; Wenzel, W A; Barrett, M; Ford, K E; Harrison, T J; Hart, A J; Hawkes, C M; Morgan, S E; Watson, A T; Fritsch, M; Goetzen, K; Held, T; Koch, H; Lewandowski, B; Pelizaeus, M; Peters, K; Schröder, T; Steinke, M; Boyd, J T; Burke, J P; Cottingham, W N; Walker, D; Çuhadar-Dönszelmann, T; Fulsom, B G; Hearty, C; Knecht, N S; Mattison, T S; McKenna, J A; Khan, A; Kyberd, P; Saleem, M; Teodorescu, L; Blinov, V E; Bukin, A D; Buzykaev, A R; Druzhinin, V P; Golubev, V B; Onuchin, A P; Serednyakov, S I; Skovpen, Yu I; Solodov, E P; Todyshev, Yu K; Bondioli, M; Bruinsma, M; Chao, M; Curry, S; Eschrich, I; Kirkby, D; Lankford, A J; Lund, P; Mandelkern, M A; Mommsen, R K; Röthel, W; Stoker, D P; Abachi, S; Buchanan, C; Foulkes, S D; Gary, J W; Long, O; Shen, B C; Wang, K; Zhang, L; Del Re, D; Hadavand, H K; Hill, E J; Paar, H P; Rahatlou, S; Sharma, V; Berryhill, J W; Campagnari, C; Cunha, A; Dahmes, B; Hong, T M; Richman, J D; Beck, T W; Eisner, A M; Flacco, C J; Heusch, C A; Kroseberg, J; Lockman, W S; Nesom, G; Schalk, T; Schumm, B A; Seiden, A; Spradlin, P; Williams, D C; Wilson, M G; Albert, J; Chen, E; Dubois-Felsmann, G P; Dvoretskii, A; Hitlin, D G; Narsky, I; Piatenko, T; Porter, F C; Ryd, A; Samuel, A; Andreassen, R; Mancinelli, G; Meadows, B T; Sokoloff, M D; Blanc, F; Bloom, P C; Chen, S; Ford, W T; Hirschauer, J F; Kreisel, A; Nauenberg, U; Olivas, A; Ruddick, W O; Smith, J G; Ulmer, K A; Wagner, S R; Zhang, J; Chen, A; Eckhart, E A; Soffer, A; Toki, W H; Wilson, R J; Winklmeier, F; Zeng, Q; Altenburg, D D; Feltresi, E; Hauke, A; Jasper, H; Spaan, B; Brandt, T; Klose, V; Lacker, H M; Nogowski, R; Petzold, A; Schubert, J; Schubert, K R; Schwierz, R; Sundermann, J E; Volk, A; Bernard, D; Bonneaud, G R; Grenier, P; Latour, E; Thiebaux, C; Verderi, M; Bard, D J; Clark, P J; Gradl, W; Muheim, F; Playfer, S; Xie, Y; Andreotti, M; Bettoni, D; Bozzi, C; Calabrese, R; Cibinetto, G; Luppi, E; Negrini, M; Piemontese, L; Anulli, F; Baldini-Ferroli, R; Calcaterra, A; De Sangro, R; Finocchiaro, G; Pacetti, S; Patteri, P; Peruzzi, I M; Piccolo, M; Rama, M; Zallo, A; Buzzo, A; Capra, R; Contri, R; Lo Vetere, M; Macri, M M; Monge, M R; Passaggio, S; Patrignani, C; Robutti, E; Santroni, A; Tosi, S; Brandenburg, G; Chaisanguanthum, K S; Morii, M; Wu, J; Dubitzky, R S; Marks, J; Schenk, S; Uwer, U; Bhimji, W; Bowerman, D A; Dauncey, P D; Egede, U; Flack, R L; Gaillard, J R; Nash, J A; Nikolich, M B; Panduro-Vazquez, W; Chai, X; Charles, M J; Mader, W F; Mallik, U; Ziegler, V; Cochran, J; Crawley, H B; Dong, L; Eyges, V; Meyer, W T; Prell, S; Rosenberg, E I; Rubin, A E; Schott, G; Arnaud, N; Davier, M; Grosdidier, G; Höcker, A; Le Diberder, F R; Lepeltier, V; Lutz, A M; Oyanguren, A; Petersen, T C; Pruvot, S; Rodier, S; Roudeau, P; Schune, M H; Stocchi, A; Wang, W F; Wormser, G; Cheng, C H; Lange, D J; Wright, D M; Chavez, C A; Forster, I J; Fry, J R; Gabathuler, E; Gamet, R; George, K A; Hutchcroft, D E; Payne, D J; Schofield, K C; Touramanis, C; Bevan, A J; Di Lodovico, F; Menges, W; Sacco, R; Brown, C L; Cowan, G; Flächer, H U; Hopkins, D A; Jackson, P S; McMahon, T R; Ricciardi, S; Salvatore, F; Davis, C L; Allison, J; Barlow, N R; Barlow, R J; Chia, Y M; Edgar, C L; Kelly, M P; Lafferty, G D; Naisbit, M T; Williams, J C; Yi, J I; Chen, C; Hulsbergen, W D; Jawahery, A; Kovalskyi, D; Lae, C K; Roberts, D A; Simi, G; Blaylock, G; Dallapiccola, C; Hertzbach, S S; Li, X; Moore, T B; Saremi, S; Stängle, H; Willocq, S Y; Cowan, R; Koeneke, K; Sciolla, G; Sekula, S J; Spitznagel, M; Taylor, F; Yamamoto, R K; Kim, H; Patel, P M; Potter, C T; Robertson, S H; Lazzaro, A; Lombardo, V; Palombo, F; Bauer, J M; Cremaldi, L; Eschenburg, V; Godang, R; Kroeger, R; Reidy, J; Sanders, D A; Summers, D J; Zhao, H W; Brunet, S; Côté, D; Simard, M; Taras, P; Viaud, F B; Nicholson, H; Cavallo, N; De Nardo, Gallieno; Fabozzi, F; Gatto, C; Lista, L; Monorchio, D; Paolucci, P; Piccolo, D; Sciacca, C; Baak, M; Bulten, H; Raven, G; Snoek, H L; Jessop, C P; LoSecco, J M; Allmendinger, T; Benelli, G; Gan, K K; Honscheid, K; Hufnagel, D; Jackson, P D; Kagan, H; Kass, R; Pulliam, T; Rahimi, A M; Ter-Antonian, R; Wong, Q K; Blount, N L; Brau, J E; Frey, R; Igonkina, O; Lu, M; Rahmat, R; Sinev, N B; Strom, D; Strube, J; Torrence, E; Galeazzi, F; Gaz, A; Margoni, M; Morandin, M; Pompili, A; Posocco, M; Rotondo, M; Simonetto, F; Stroili, R; Voci, C; Benayoun, M; Chauveau, J; David, P; Del Buono, L; La Vaissière, C de; Hamon, O; Hartfiel, B L; John, M J J; Leruste, P; Malcles, J; Ocariz, J; Roos, L; Therin, G; Behera, P K; Gladney, L; Panetta, J; Biasini, M; Covarelli, R; Pioppi, M; Angelini, C; Batignani, G; Bettarini, S; Bucci, F; Calderini, G; Carpinelli, M; Cenci, R; Forti, F; Giorgi, M A; Lusiani, A; Marchiori, G; Mazur, M A; Morganti, M; Neri, N; Paoloni, E; Rizzo, G; Walsh, J; Haire, M; Judd, D; Wagoner, D E; Biesiada, J; Danielson, N; Elmer, P; Lau, Y P; Lü, C; Olsen, J; Smith, A J S; Telnov, A V; Bellini, F; Cavoto, G; D'Orazio, A; Di, E; Marco; Faccini, R; Ferrarotto, F; Ferroni, F; Gaspero, M; Li Gioi, L; Mazzoni, M A; Morganti, S; Piredda, G; Polci, F; Safai-Tehrani, F; Voena, C; Schröder, H; Waldi, R; Adye, T; De Groot, N; Franek, B; Olaiya, E O; Wilson, F F; Emery, S; Gaidot, A; Ganzhur, S F; Hamel de Monchenault, G; Kozanecki, Witold; Legendre, M; Mayer, B; Vasseur, G; Yéche, C; Zito, M; Park, W; Purohit, M V; Weidemann, A W; Wilson, J R; Allen, M T; Aston, D; Bartoldus, R; Bechtle, P; Berger, N; Boyarski, A M; Claus, R; Coleman, J P; Convery, M R; Cristinziani, M; Dingfelder, J C; Dong, D; Dorfan, J; Dujmic, D; Dunwoodie, W M; Field, R C; Glanzman, T; Gowdy, S J; Halyo, V; Hast, C; Hrynóva, T; Innes, W R; Kelsey, M H; Kim, P; Kocian, M L; Leith, D W G S; Libby, J; Luitz, S; Lüth, V; Lynch, H L; MacFarlane, D B; Marsiske, H; Messner, R; Müller, D R; O'Grady, C P; Ozcan, V E; Perazzo, A; Perl, M; Ratcliff, B N; Roodman, A; Salnikov, A A; Schindler, R H; Schwiening, J; Snyder, A; Stelzer, J; Su, D; Sullivan, M K; Suzuki, K; Swain, S K; Thompson, J M; Vavra, J; Van Bakel, N; Weaver, M; Weinstein, A J R; Wisniewski, W J; Wittgen, M; Wright, D H; Yarritu, A K; Yi, K; Young, C C; Burchat, P R; Edwards, A J; Majewski, S A; Petersen, B A; Roat, C; Wilden, L; Ahmed, S; Alam, M S; Bula, R; Ernst, J A; Jain, V; Pan, B; Saeed, M A; Wappler, F R; Zain, S B; Bugg, W; Krishnamurthy, M; Spanier, S M; Eckmann, R; Ritchie, J L; Satpathy, A; Schwitters, R F; Izen, J M; Kitayama, I; Lou, X C; Ye, S; Bianchi, F; Bóna, M; Gallo, F; Gamba, D; Bomben, M; Bosisio, L; Cartaro, C; Cossutti, F; Della Ricca, G; Dittongo, S; Grancagnolo, S; Lanceri, L; Vitale, L; Azzolini, V; Martínez-Vidal, F; Panvini, R S; Banerjee, Sw; Bhuyan, B; Brown, C M; Fortin, D; Hamano, K; Kowalewski, R V; Nugent, I M; Roney, J M; Sobie, R J; Back, J J; Harrison, P F; Latham, T E; Mohanty, G B; Band, H R; Chen, X; Cheng, B; Dasu, S; Datta, M; Eichenbaum, A M; Flood, K T; Graham, M T; Hollar, J J; Johnson, J R; Kutter, P E; Li, H; Liu, R; Mellado, B; Mihályi, A; Mohapatra, A K; Pan, Y; Pierini, M; Prepost, R; Tan, P; Wu, S L; Yu, Z; Neal, H

    2006-01-01

    We present a study of the decays B0bar --> D(*)0 K(*)0bar using a sample of 226 million Y(4S) --> B Bbar decays collected with the BaBar detector at the PEP-II asymmetric-energy e+e-collider at SLAC. We report evidence for the decay of B0 and B0bar mesons to the D*0 K0s final state with an average branching fraction BF(B0-tilde --> D*0 K0bar) := [ BF(B0bar --> D*0 K0bar) + BF(B0 --> D*0 K0) ]/2 = (3.6 +- 1.2 +- 0.3) x 10^-5. Similarly, we measure BF(B0-tilde --> D0 K0bar) := [ BF(B0bar --> D0 K0bar) + BF(B0 --> D0 K0) ]/2 = (5.3 +- 0.7 +- 0.3) x 10^-5 forthe D0 K0s final state. We measure BF(B0bar --> D0 K*0bar) =^(4.0 +- 0.7 +- 0.3) x 10^-5 and set a 90% confidence level upper limit BF(B0bar --> D0bar K*0bar) D0bar K*0bar)/A(B0bar --> D0 K*0bar)| to be less than 0.4 at the 90% confidence level.

  6. Dynamically possible pattern speeds of double bars

    CERN Document Server

    Maciejewski, Witold

    2009-01-01

    The method to study oscillating potentials of double bars, based on invariant loops, is introduced here in a new way, intended to be more intelligible. Using this method, I show how the orbital structure of a double-barred galaxy (nested bars) changes with the variation of nuclear bar's pattern speed. Not all pattern speeds are allowed when the inner bar rotates in the same direction as the outer bar. Below certain minimum pattern speed orbital support for the inner bar abruptly disappears, while high values of this speed lead to loops that are increasingly round. For values between these two extremes, loops supporting the inner bar extend further out as its pattern speed decreases, and they become more eccentric and pulsate more. These findings do not apply to counter-rotating inner bars.

  7. Supervised Transfer Sparse Coding

    KAUST Repository

    Al-Shedivat, Maruan

    2014-07-27

    A combination of the sparse coding and transfer learn- ing techniques was shown to be accurate and robust in classification tasks where training and testing objects have a shared feature space but are sampled from differ- ent underlying distributions, i.e., belong to different do- mains. The key assumption in such case is that in spite of the domain disparity, samples from different domains share some common hidden factors. Previous methods often assumed that all the objects in the target domain are unlabeled, and thus the training set solely comprised objects from the source domain. However, in real world applications, the target domain often has some labeled objects, or one can always manually label a small num- ber of them. In this paper, we explore such possibil- ity and show how a small number of labeled data in the target domain can significantly leverage classifica- tion accuracy of the state-of-the-art transfer sparse cod- ing methods. We further propose a unified framework named supervised transfer sparse coding (STSC) which simultaneously optimizes sparse representation, domain transfer and classification. Experimental results on three applications demonstrate that a little manual labeling and then learning the model in a supervised fashion can significantly improve classification accuracy.

  8. Bars in the Barkor Street

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In daytime,the Barkor Street is bustling with tourists,pious pilgrims and merchants crowded together.Only when darkness falls does the street become tranquil.Nevertheless,the area surrounding the Barkor Street(from Tibetan Hospital compound extending to east Beijing Road)is then revived by various kinds of bars.

  9. Bars in Beijing Old Town

    Institute of Scientific and Technical Information of China (English)

    GUANYUNZHANG

    2003-01-01

    It's seven pm on a summer's evening by Shichahao Lake,central Beijing.A welcome breeze whispers across the lake,and the ruddy vestiges of sunset linger on roofs and treetops.A low hum emanates from bars on the lakeshore packed with young people chatting,drinking and generally

  10. Galaxy Zoo: Observing Secular Evolution Through Bars

    CERN Document Server

    Cheung, Edmond; Masters, Karen L; Nichol, Robert C; Bosma, A; Bell, Eric F; Faber, S M; Koo, David C; Lintott, Chris; Melvin, Thomas; Schawinski, Kevin; Skibba, Ramin A; Willett, Kyle W

    2013-01-01

    Observations have shown that there is a connection between the presence of a bar and the properties of a galaxy. In a parallel effort, simulations have shown that this connection is consistent with the theory of bar-driven secular evolution. But observational evidence of bar-driven secular evolution has been sparse. In this paper, we use the Galaxy Zoo 2 dataset to look for evidence of this secular evolution. Our sample consists of 13,295 disk galaxies, with an overall bar fraction of 23.6 +/- 0.4%, of which 1,154 barred galaxies also have bar length measurements. These samples are the largest ever used to study the role of bars in disk galaxy evolution. We characterize bars by the bar likelihood, the likelihood a bar is present in a given galaxy, and the bar length. These two bar properties show interesting correlations with the specific star formation rate and the inner central structure of galaxies. Comparing these observations to state-of-the-art simulations of bar evolution, which include live halos and ...

  11. Analysis of a calculation method for the determination of the value of safety or control bars

    International Nuclear Information System (INIS)

    Due to the control or safety bars in a nuclear reactor are constituted by strongly absorbent materials, the Diffusion Theory like tool for the calculation of bar values is not directly applicable, should it use the Transport Theory. However the speed and economy of the Diffusion codes for the reactors calculation, those make attractiveness and by this reason its are used in the determination of characteristic parameters and even in the determination of bar values, not without before to make some theoretical developments that allow to make applicable this theory. The application of the Diffusion Theory in strongly absorbent media is based on the use of some effective cross sections distinct from the real ones obtained when imposing the reason that among the flow and it gradient in the external surface of such media (control element in general, bar type or flagstone) be similar to the one obtained using Transport Theory in all the control region (multiplicative and absorbent media) with those real cross sections. The effective cross sections were obtained of the Leopard-NUMICE cell code which has incorporate the respective calculation theory of effective cross sections. Later these constants its were used in the bidimensional diffusion code Exterminator-II, simulating in it, the distribution of safety or control bars. From the cell code its were also obtained the respective constants of the homogeneous fuel cell. The results as soon as those obtained bar values of the diffusion code, its were compared with some experimental results obtained in the Rφ Swedish reactor of natural uranium and heavy water. In this work an analysis of the bar value of one of them, trying to determine the applicability of the method is made. (Author)

  12. Going Smokefree Matters - Bars and Restaurants Infographic

    Data.gov (United States)

    U.S. Department of Health & Human Services — Explore the Going Smokefree Matters – Bars and Restaurants Infographic which outlines key facts related to the effects of secondhand smoke exposure in bars and...

  13. Bar, Orliac-de-Bar, Beaumont, Saint–Augustin, Ussel

    OpenAIRE

    Simonnot, Bernard

    2013-01-01

    Identifiant de l'opération archéologique : 2735 Date de l'opération : 2007 (PR) Inventeur(s) : Simonnot Bernard (BEN) La prospection sur les communes de Bar, Orliac-de-Bar, Beaumont et Saint-Augustin n’ayant pas donné pour le moment de nouveaux résultats satisfaisants, une reprise sera nécessaire lors de la prochaine campagne. Ceux découverts récemment demandent une étude plus approfondie. Cette année, la prospection s’est limitée à la partie ouest de la commune d’Ussel, dans la zone de renc...

  14. Quantitative risk assessment of foods containing peanut advisory labeling.

    Science.gov (United States)

    Remington, Benjamin C; Baumert, Joseph L; Marx, David B; Taylor, Steve L

    2013-12-01

    Foods with advisory labeling (i.e. "may contain") continue to be prevalent and the warning may be increasingly ignored by allergic consumers. We sought to determine the residual levels of peanut in various packaged foods bearing advisory labeling, compare similar data from 2005 and 2009, and determine any potential risk for peanut-allergic consumers. Of food products bearing advisory statements regarding peanut or products that had peanut listed as a minor ingredient, 8.6% and 37.5% contained detectable levels of peanut (>2.5 ppm whole peanut), respectively. Peanut-allergic individuals should be advised to avoid such products regardless of the wording of the advisory statement. Peanut was detected at similar rates and levels in products tested in both 2005 and 2009. Advisory labeled nutrition bars contained the highest levels of peanut and an additional market survey of 399 products was conducted. Probabilistic risk assessment showed the risk of a reaction to peanut-allergic consumers from advisory labeled nutrition bars was significant but brand-dependent. Peanut advisory labeling may be overused on some nutrition bars but prudently used on others. The probabilistic approach could provide the food industry with a quantitative method to assist with determining when advisory labeling is most appropriate. PMID:23994086

  15. QR CODE GENERATION AND APPLICATION OF ANTI-FALSIFICATION

    OpenAIRE

    Ke LIAO

    2016-01-01

    QR code is 2-dimensional bar code. It is more advanced than bar code, which can only store numbers and characters. QR code can store numbers, characters (including Chinese characters) and even images. It has great data capacity and allows for error correction. It is commonly used to spread information and is sometimes used to achieve website login function. It can even be encrypted that the user has to enter password to get the original information. In my thesis, I come up with an idea tha...

  16. Coding Partitions

    Directory of Open Access Journals (Sweden)

    Fabio Burderi

    2007-05-01

    Full Text Available Motivated by the study of decipherability conditions for codes weaker than Unique Decipherability (UD, we introduce the notion of coding partition. Such a notion generalizes that of UD code and, for codes that are not UD, allows to recover the ``unique decipherability" at the level of the classes of the partition. By tacking into account the natural order between the partitions, we define the characteristic partition of a code X as the finest coding partition of X. This leads to introduce the canonical decomposition of a code in at most one unambiguouscomponent and other (if any totally ambiguouscomponents. In the case the code is finite, we give an algorithm for computing its canonical partition. This, in particular, allows to decide whether a given partition of a finite code X is a coding partition. This last problem is then approached in the case the code is a rational set. We prove its decidability under the hypothesis that the partition contains a finite number of classes and each class is a rational set. Moreover we conjecture that the canonical partition satisfies such a hypothesis. Finally we consider also some relationships between coding partitions and varieties of codes.

  17. Bar instabilities in Coma cluster galaxies

    International Nuclear Information System (INIS)

    The radial distribution of bar versus nonbar galaxies within the Coma cluster shows that a significantly larger fraction of bar galaxies are members of the cluster core. This result can be used either to estimate the time scale for the decay of bar instabilities or to argue that galaxies in the core of Coma are confined within the core

  18. While in Shanghai,Enjoy Unigue Bars!

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    Today, bars are nothingnew for people who live inmajor cities. Bars have becomeso common that they have toseek a revolution for survival.It seems the only way tosurvive the fierce market competitionis to take the lead in being special. Asa result, some bars are attractingcustomers with unique features.Among them are:

  19. BARS curve in Romanian economy

    OpenAIRE

    Emilian Dobrescu

    2015-01-01

    The paper is consacrated to the binomial “public budget-global output” from the BARS curve perspective. The first section characterizes the main conceptual premises of this approach. The second is devoted to empirical analysis, using the statistical data (1990- 2013) for Romania, an European emergent economy: three cointegrating regressions (fully modified least squares, canonical cointegrating regression and dynamic least squares) and three algorithms based on instrumental variables (two-sta...

  20. Galaxy Zoo: Observing secular evolution through bars

    International Nuclear Information System (INIS)

    In this paper, we use the Galaxy Zoo 2 data set to study the behavior of bars in disk galaxies as a function of specific star formation rate (SSFR) and bulge prominence. Our sample consists of 13,295 disk galaxies, with an overall (strong) bar fraction of 23.6% ± 0.4%, of which 1154 barred galaxies also have bar length (BL) measurements. These samples are the largest ever used to study the role of bars in galaxy evolution. We find that the likelihood of a galaxy hosting a bar is anticorrelated with SSFR, regardless of stellar mass or bulge prominence. We find that the trends of bar likelihood and BL with bulge prominence are bimodal with SSFR. We interpret these observations using state-of-the-art simulations of bar evolution that include live halos and the effects of gas and star formation. We suggest our observed trends of bar likelihood with SSFR are driven by the gas fraction of the disks, a factor demonstrated to significantly retard both bar formation and evolution in models. We interpret the bimodal relationship between bulge prominence and bar properties as being due to the complicated effects of classical bulges and central mass concentrations on bar evolution and also to the growth of disky pseudobulges by bar evolution. These results represent empirical evidence for secular evolution driven by bars in disk galaxies. This work suggests that bars are not stagnant structures within disk galaxies but are a critical evolutionary driver of their host galaxies in the local universe (z < 1).

  1. code {poems}

    Directory of Open Access Journals (Sweden)

    Ishac Bertran

    2012-08-01

    Full Text Available "Exploring the potential of code to communicate at the level of poetry," the code­ {poems} project solicited submissions from code­writers in response to the notion of a poem, written in a software language which is semantically valid. These selections reveal the inner workings, constitutive elements, and styles of both a particular software and its authors.

  2. Maternal Label and Gesture Use Affects Acquisition of Specific Object Names

    Science.gov (United States)

    Zammit, Maria; Schafer, Graham

    2011-01-01

    Ten mothers were observed prospectively, interacting with their infants aged 0 ; 10 in two contexts (picture description and noun description). Maternal communicative behaviours were coded for volubility, gestural production and labelling style. Verbal labelling events were categorized into three exclusive categories: label only; label plus…

  3. Effect of bars on the galaxy properties

    CERN Document Server

    Vera, Matias; Coldwell, Georgina

    2016-01-01

    Aims: With the aim of assessing the effects of bars on disc galaxy properties, we present an analysis of different characteristics of spiral galaxies with strong, weak and without bars. Method: We identified barred galaxies from the Sloan Digital Sky Survey. By visual inspection, we classified the face-on spiral galaxies brighter than g<16.5 mag into strong-bar, weak-bar and unbarred. In order to provide an appropiate quantification of the influence of bars on galaxy properties, we also constructed a suitable control sample of unbarred galaxies with similar redshift, magnitude, morphology, bulge sizes, and local density environment distributions to that of barred galaxies. Results: We found 522 strong-barred and 770 weak-barred galaxies, representing a 25.82% of the full sample of spiral galaxies, in good agreement with previous studies. We also found that strong-barred galaxies show less efficient star formation activity and older stellar populations compared to weak-barred and unbarred spirals from the c...

  4. A diffractive barcode using diffusion-dot lines to form intersected bright bars with different orientations

    Science.gov (United States)

    Lih Yeh, Sheng; Lin, Shyh Tsong; Wu, Ming Wei

    2010-11-01

    Conventional barcodes can perform well for the data management of commercial products, but they cannot be used for anti-counterfeiting. Therefore, this paper will propose a new barcode with macro- and micro-anti-counterfeiting features. A barcode image for a conventional barcode is composed of parallel bars with different widths, whereas a barcode image for the new barcode is composed of intersected bars with different orientations. Codes for the proposed barcode are composed of bright bars along four possible orientations only. The proposed barcode pattern possesses many parallel diffusion-dot lines. Because diffusion-dot lines can diffract a laser beam to form different bright bar arrangements corresponding to different codes, the proposed barcode is called a 'diffractive barcode' here. There are brightness and length differences between the bars in a bright bar image and the differences are difficult to counterfeit, so the macrofeatures can be used for anti-counterfeiting. On the other hand, because the appearances of the diffusion dots are special and they cannot be reproduced, the microfeatures can be used for anti-counterfeiting. Moreover, both the encoding and decoding work of the diffractive barcode are easy.

  5. A diffractive barcode using diffusion-dot lines to form intersected bright bars with different orientations

    International Nuclear Information System (INIS)

    Conventional barcodes can perform well for the data management of commercial products, but they cannot be used for anti-counterfeiting. Therefore, this paper will propose a new barcode with macro- and micro-anti-counterfeiting features. A barcode image for a conventional barcode is composed of parallel bars with different widths, whereas a barcode image for the new barcode is composed of intersected bars with different orientations. Codes for the proposed barcode are composed of bright bars along four possible orientations only. The proposed barcode pattern possesses many parallel diffusion-dot lines. Because diffusion-dot lines can diffract a laser beam to form different bright bar arrangements corresponding to different codes, the proposed barcode is called a 'diffractive barcode' here. There are brightness and length differences between the bars in a bright bar image and the differences are difficult to counterfeit, so the macrofeatures can be used for anti-counterfeiting. On the other hand, because the appearances of the diffusion dots are special and they cannot be reproduced, the microfeatures can be used for anti-counterfeiting. Moreover, both the encoding and decoding work of the diffractive barcode are easy

  6. A secularly evolved model for the Milky Way bar and bulge

    Science.gov (United States)

    Martinez-Valpuesta, Inma; Gerhard, Ortwin

    2015-03-01

    Bars are strong drivers of secular evolution in disk galaxies. Bars themselves can evolve secularly through angular momentum transport, producing different boxy/peanut and X-shaped bulges. Our Milky Way is an example of a barred galaxy with a boxy bulge. We present a self-consistent N-body simulation of a barred galaxy which matches remarkably well the structure of the inner Milky Way deduced from star counts. In particular, features taken as signatures of a second ``long bar`` can be explained by the interaction between the bar and the spiral arms of the galaxy (Martinez-Valpuesta & Gerhard 2011). Furthermore the structural change in the bulge inside l = 4° measured recently from VVV data can be explained by the high-density near-axisymmetric part of the inner boxy bulge (Gerhard & Martinez-Valpuesta 2012). We also compare this model with kinematic data from recent spectroscopic surveys. We use a modified version of the NMAGIC code (de Lorenzi et al. 2007) to study the properties of the Milky Way bar, obtaining an upper limit for the pattern speed of ~ 42 km/sec/kpc. See Fig. 1 for a comparison of one of our best models with BRAVA data (Kunder et al. 2012).

  7. Issues in Data Labelling

    NARCIS (Netherlands)

    Cowie, Roddy; Cox, Cate; Martin, Jeam-Claude; Batliner, Anton; Heylen, Dirk; Karpouzis, Kostas; Cowie, Roddy; Pelachaud, Catherine; Petta, Paolo

    2011-01-01

    Labelling emotion databases is not a purely technical matter. It is bound up with theoretical issues. Different issues affect labelling of emotional content, labelling of the signs that convey emotion, and labelling of the relevant context. Linked to these are representational issues, involving time

  8. Holographic codes

    CERN Document Server

    Latorre, Jose I

    2015-01-01

    There exists a remarkable four-qutrit state that carries absolute maximal entanglement in all its partitions. Employing this state, we construct a tensor network that delivers a holographic many body state, the H-code, where the physical properties of the boundary determine those of the bulk. This H-code is made of an even superposition of states whose relative Hamming distances are exponentially large with the size of the boundary. This property makes H-codes natural states for a quantum memory. H-codes exist on tori of definite sizes and get classified in three different sectors characterized by the sum of their qutrits on cycles wrapped through the boundaries of the system. We construct a parent Hamiltonian for the H-code which is highly non local and finally we compute the topological entanglement entropy of the H-code.

  9. On the Fraction of Barred Spiral Galaxies

    CERN Document Server

    Nair, Preethi B

    2010-01-01

    We investigate the stellar masses of strongly barred spiral galaxies. Our analysis is based on a sample of ~14000 visually-classified nearby galaxies given in Nair & Abraham 2010(a). The fraction of barred spiral galaxies is found to be a strong function of stellar mass and star formation history, with a minimum near the characteristic mass at which bimodality is seen in the stellar populations of galaxies. We also find bar fractions are very sensitive to the central concentration of galaxies below the transition mass but not above it. This suggests that whatever process is causing the creation of the red and blue sequences is either influencing, or being influenced by, structural changes which manifest themselves in the absence of bars. As a consequence of strong bar fractions being sensitive to the mass range probed, our analysis helps resolve discrepant results on the reported evolution of bar fractions with redshift.

  10. Results from bar pp colliders

    International Nuclear Information System (INIS)

    Recent results bar pp colliders are presented. From elastic scattering experiments at the Tevatron, an average value of σtot = 72.1±2 mb is reported, along with a new measurement of ρ = 0.13 ± 0.7. New measurements of jet direct photon and high pt W and Z production are compared to more precise, higher order predictions from perturbative QCD. Recently available data on the W mass and width give combined values for MW = 80.14±0.27 GeV/c2, and Γ(W) =2. 14 ± 0.08 GeV. From electroweak radiative corrections and MW, one finds Mtop = 130±40 GeV/c2, with a 95% C.L. upper limit at 210 GeV/c2. Current limits on Mtop are presented, along with a review of the prospects for top discovery. From jet data there is no evidence of quark substructure down to the distance scale of 1.4 x 10-17 cm, nor is there evidence for supersymmetry or heavy gauge bosons at bar pp colliders, allowing lower limits on MW, > 520 GeV/c2 and MZ 412 GeV/c2. 66 refs., 26 figs

  11. {bar K}-NUCLEAR Deeply Bound States?

    Science.gov (United States)

    Gal, Avraham

    Following the prediction by Akaishi and Yamazaki of relatively narrow {bar K}-nuclear states, deeply bound by over 100 MeV where the main decay channel {bar K} N -> π Σ is closed, several experimental signals in stopped K- reactions on light nuclei have been interpreted recently as due to such states. In this talk I review (i) the evidence from K--atom data for a deep bar K-nucleus potential, as attractive as V{bar K}(ρ 0) ˜ -(150 - 200) MeV at nuclear matter density, that could support such states; and (ii) the theoretical arguments for a shallow potential, V{bar K}(ρ 0) ˜ -(40 - 60) MeV. I then review a recent work by Mareš, Friedman and Gal in which {bar K}-nuclear bound states are generated dynamically across the periodic table, using a RMF Lagrangian that couples the {bar K} to the scalar and vector meson fields mediating the nuclear interactions. The reduced phase space available for {bar K} absorption from these bound states is taken into account by adding a density- and energy-dependent imaginary term, underlying the corresponding {bar K}-nuclear level widths, with a strength constrained by K--atom fits. Substantial polarization of the core nucleus is found for light nuclei, with central nuclear densities enhanced by almost a factor of two. The binding energies and widths calculated in this dynamical model differ appreciably from those calculated for a static nucleus. These calculations provide a lower limit of Γ {bar K} ˜ 50 ± 10 MeV on the width of nuclear bound states for {bar K} binding energy in the range B{bar K} = 100 - 200 MeV.

  12. Installation of Shimming Bars for CYCIAE-100

    Institute of Scientific and Technical Information of China (English)

    LV; Yin-long; WANG; Zhen-hui; ZHONG; Jun-qing; LIU; Geng-shou

    2012-01-01

    <正>The 100 MeV high intensity proton cyclotron, CYCIAE-100, is the most critical equipment of the BRIF project at CIAE. The shimming bars are used to get the isochronous magnetic field. In the process of magnetic mapping and shimming, the bars should be repeated the installed and disassembly for about 10 times. Each time the installation precision must be ensured. The bars installation schedule and quality are directly related to the BRIF project progress.

  13. Dynamical mechanisms supporting barred-spiral structures

    Science.gov (United States)

    Patsis, P. A.

    We review some recent results of the orbital theory, related with the dynamics of barred-spiral galaxies. The method we use is to study the responses of stellar and gaseous disks when time-independent, external potentials are imposed. These potentials are directly estimated from near-infrared images of disk galaxies. The goal of the work is to detect dynamical mechanisms that reinforce the bars and the spirals in realistic systems. Besides the known mechanism for building bars by quasiperiodic orbits trapped around stable orbits of the {xx} family, we find cases where bars can be supported, to a large extent, by chaotic orbits. These bars are of the ``ansae'' type and their effective potentials are characterized by multiple Lagrangian points roughly along the major axis of the bar. On the other hand the spirals are supported mainly by chaotic orbits and extend usually beyond corotation. We find that the spirals and the outer parts of the bars share the same orbital content. However, we have found also barred-spiral systems with spirals inside corotation, consisting mainly by chaotic orbits. Finally we indicate, that in barred-spiral systems with different pattern speeds for the two components, the dynamics of the spirals can be similar to the dynamics of the spirals of normal spiral galaxies.

  14. Chiral Perturbation Theory and the $\\bar B \\bar B$ Strong Interaction

    CERN Document Server

    Liu, Zhan-Wei; Zhu, Shi-Lin

    2012-01-01

    We have calculated the potentials of the heavy (charmed or bottomed) pseudoscalar mesons up to $O(\\epsilon^2)$ with the heavy meson chiral perturbation theory. We take into account the contributions from the football, triangle, box, and crossed diagrams with the 2$\\phi$ exchange and one-loop corrections to the contact terms. We notice that the total 2$\\phi$-exchange potential alone is attractive in the small momentum region in the channel ${\\bar B \\bar B}^{I=1}$, ${\\bar B_s \\bar B_s}^{I=0}$, or ${\\bar B \\bar B_s}^{I=1/2}$, while repulsive in the channel ${\\bar B \\bar B}^{I=0}$. Hopefully the analytical chiral structures of the potentials may be useful in the extrapolation of the heavy meson interaction from lattice QCD simulation.

  15. 21 CFR 660.35 - Labeling.

    Science.gov (United States)

    2010-04-01

    ... donor code in the product labeling each donor of peripheral blood used for detection or identification... IDENTIFICATION OF UNEXPECTED ANTIBODIES” or “NOT FOR USE IN DETECTION OR IDENTIFICATION OF UNEXPECTED ANTIBODIES... antibodies shall identify the number of donors contributing to the pool. Products designed exclusively...

  16. A study of B0bar --> D(*)0 K(*)bar decays

    CERN Document Server

    Aubert, B; Boutigny, D; Couderc, F; Gaillard, J M; Hicheur, A; Karyotakis, Yu; Lees, J P; Tisserand, V; Zghiche, A; Palano, A; Pompili, A; Chen, J C; Qi, N D; Rong, G; Wang, P; Zhu, Y S; Eigen, G; Ofte, I; Stugu, B; Abrams, G S; Borgland, A W; Breon, A B; Brown, D N; Button-Shafer, J; Cahn, R N; Charles, E; Day, C T; Gill, M S; Gritsan, A V; Groysman, Y; Jacobsen, R G; Kadel, R W; Kadyk, J; Kerth, L T; Kolomensky, Yu G; Kukartsev, G; Lynch, G; Mir, L M; Oddone, P J; Orimoto, T J; Pripstein, M; Roe, N A; Ronan, Michael T; Shelkov, V G; Wenzel, W A; Barrett, M; Ford, K E; Harrison, T J; Hart, A J; Hawkes, C M; Morgan, S E; Watson, A T; Fritsch, M; Goetzen, K; Held, T; Koch, H; Lewandowski, B; Pelizaeus, M; Steinke, M; Boyd, J T; Chevalier, N; Cottingham, W N; Kelly, M P; Latham, T E; Wilson, F F; Çuhadar-Dönszelmann, T; Hearty, C; Knecht, N S; Mattison, T S; McKenna, J A; Thiessen, D; Khan, A; Kyberd, P; Teodorescu, L; Blinov, A E; Blinov, V E; Druzhinin, V P; Golubev, V B; Ivanchenko, V N; Kravchenko, E A; Onuchin, A P; Serednyakov, S I; Skovpen, Yu I; Solodov, E P; Yushkov, A N; Best, D; Bruinsma, M; Chao, M; Eschrich, I; Kirkby, D; Lankford, A J; Mandelkern, M A; Mommsen, R K; Röthel, W; Stoker, D P; Buchanan, C; Hartfiel, B L; Foulkes, S D; Gary, J W; Shen, B C; Wang, K; Del Re, D; Hadavand, H K; Hill, E J; MacFarlane, D B; Paar, H P; Rahatlou, S; Sharma, V; Berryhill, J W; Campagnari, C; Dahmes, B; Long, O; Lu, A; Mazur, M A; Richman, J D; Verkerke, W; Beck, T W; Eisner, A M; Heusch, C A; Kroseberg, J; Lockman, W S; Nesom, G; Schalk, T; Schumm, B A; Seiden, A; Spradlin, P; Williams, D C; Wilson, M G; Albert, J; Chen, E; Dubois-Felsmann, G P; Dvoretskii, A; Hitlin, D G; Narsky, I; Piatenko, T; Porter, F C; Ryd, A; Samuel, A; Yang, S; Jayatilleke, S M; Mancinelli, G; Meadows, B T; Sokoloff, M D; Abe, T; Blanc, F; Bloom, P; Chen, S; Ford, W T; Nauenberg, U; Olivas, A; Rankin, P; Smith, J G; Zhang, J; Zhang, L; Chen, A; Harton, J L; Soffer, A; Toki, W H; Wilson, R J; Zeng, Q; Altenburg, D; Brandt, T; Brose, J; Dickopp, M; Feltresi, E; Hauke, A; Lacker, H M; Müller-Pfefferkorn, R; Nogowski, R; Otto, S; Petzold, A; Schubert, J; Schubert, Klaus R; Schwierz, R; Spaan, B; Sundermann, J E; Bernard, D; Bonneaud, G R; Brochard, F; Grenier, P; Schrenk, S; Thiebaux, C; Vasileiadis, G; Verderi, M; Bard, D J; Clark, P J; Lavin, D; Muheim, F; Playfer, S; Xie, Y; Andreotti, M; Azzolini, V; Bettoni, D; Bozzi, C; Calabrese, R; Cibinetto, G; Luppi, E; Negrini, M; Piemontese, L; Sarti, A; Treadwell, E; Anulli, F; Baldini-Ferroli, R; Calcaterra, A; De Sangro, R; Finocchiaro, G; Patteri, P; Peruzzi, I M; Piccolo, M; Zallo, A; Buzzo, A; Capra, R; Contri, R; Crosetti, G; Lo Vetere, M; Macri, M; Monge, M R; Passaggio, S; Patrignani, C; Robutti, E; Santroni, A; Tosi, S; Bailey, S; Brandenburg, G; Chaisanguanthum, K S; Morii, M; Won, E; Dubitzky, R S; Langenegger, U; Bhimji, W; Bowerman, D A; Dauncey, P D; Egede, U; Gaillard, J R; Morton, G W; Nash, J A; Nikolich, M B; Taylor, G P; Charles, M J; Grenier, G J; Mallik, U; Cochran, J; Crawley, H B; Lamsa, J; Meyer, W T; Prell, S; Rosenberg, E I; Rubin, A E; Yi, J; Biasini, M; Covarelli, R; Pioppi, M; Davier, M; Giroux, X; Grosdidier, G; Höcker, A; Laplace, S; Le Diberder, F R; Lepeltier, V; Lutz, A M; Petersen, T C; Plaszczynski, S; Schune, M H; Tantot, L; Wormser, G; Cheng, C H; Lange, D J; Simani, M C; Wright, D M; Bevan, A J; Chavez, C A; Coleman, J P; Forster, I J; Fry, J R; Gabathuler, Erwin; Gamet, R; Hutchcroft, D E; Parry, R J; Payne, D J; Sloane, R J; Touramanis, C; Back, J J; Harrison, P F; Mohanty, G B; Cowan, G; Flack, R L; Flächer, H U; Green, M G; Jackson, P S; McMahon, T R; Ricciardi, S; Salvatore, F; Winter, M A; Brown, D; Davis, C L; Allison, J; Barlow, N R; Barlow, R J; Hart, P A; Hodgkinson, M C; Lafferty, G D; Lyon, A J; Williams, J C; Farbin, A; Hulsbergen, W D; Jawahery, A; Kovalskyi, D; Lae, C K; Lillard, V; Roberts, D A; Blaylock, G; Dallapiccola, C; Flood, K T; Hertzbach, S S; Kofler, R; Koptchev, V B; Moore, T B; Saremi, S; Stängle, H; Willocq, S; Cowan, R; Sciolla, G; Sekula, S J; Taylor, F; Yamamoto, R K; Mangeol, D J J; Patel, P M; Robertson, S H; Lazzaro, A; Lombardo, V; Palombo, F; Bauer, J M; Cremaldi, L M; Eschenburg, V; Godang, R; Kroeger, R; Reidy, J; Sanders, D A; Summers, D J; Zhao, H W; Brunet, S; Côté, D; Taras, P; Nicholson, H; Cavallo, N; Lista, L; Monorchio, D; Paolucci, P; Piccolo, D; Sciacca, C; Baak, M; Bulten, H; Raven, G; Snoek, H L; Wilden, L; Jessop, C P; LoSecco, J M; Allmendinger, T; Gan, K K; Honscheid, K; Hufnagel, D; Kagan, H; Kass, R; Pulliam, T; Rahimi, A M; Ter-Antonian, R; Wong, Q K; Brau, J E; Frey, R; Igonkina, O; Potter, C T; Sinev, N B; Strom, D; Torrence, E; Colecchia, F; Dorigo, A; Galeazzi, F; Margoni, M; Morandin, M; Posocco, M; Rotondo, M; Simonetto, F; Stroili, R; Tiozzo, G; Voci, C; Benayoun, M; Briand, H; Chauveau, J; David, P; La Vaissière, C de; Del Buono, L; Hamon, O; John, M J J; Leruste, P; Malcles, J; Ocariz, J; Pivk, M; Roos, L; T'Jampens, S; Therin, G; Manfredi, P F; Re, V; Behera, P K; Gladney, L; Guo, Q H; Panetta, J; Angelini, C; Batignani, G; Bettarini, S; Bondioli, M; Bucci, F; Calderini, G; Carpinelli, M; Forti, F; Giorgi, M A; Lusiani, A; Marchiori, G; Martínez-Vidal, F; Neri, N; Paoloni, E; Rama, M; Rizzo, G; Sandrelli, F; Walsh, J; Haire, M; Judd, D; Paick, K; Wagoner, D E; Danielson, N; Elmer, P; Lau, Y P; Lü, C; Miftakov, V; Olsen, J; Smith, A J S; Telnov, A V; Bellini, F; Cavoto, G; Faccini, R; Ferrarotto, F; Ferroni, F; Gaspero, M; Li Gioi, L; Mazzoni, M A; Morganti, S; Pierini, M; Piredda, G; Safai-Tehrani, F; Voena, C; Christ, S; Wagner, G; Waldi, R; Adye, T; De Groot, N; Franek, B J; Geddes, N I; Gopal, G P; Olaiya, E O; Aleksan, Roy; Emery, S; Gaidot, A; Ganzhur, S F; Giraud, P F; Hamel de Monchenault, G; Kozanecki, Witold; Legendre, M; London, G W; Mayer, B; Schott, G; Vasseur, G; Yéche, C; Zito, M; Purohit, M V; Weidemann, A W; Wilson, J R; Yumiceva, F X; Aston, D; Bartoldus, R; Berger, N; Boyarski, A M; Buchmüller, O L; Claus, R; Convery, M R; Cristinziani, M; De Nardo, Gallieno; Dong, D; Dorfan, J; Dujmic, D; Dunwoodie, W M; Elsen, E E; Fan, S; Field, R C; Glanzman, T; Gowdy, S J; Hadig, T; Halyo, V; Hast, C; Hrynóva, T; Innes, W R; Kelsey, M H; Kim, P; Kocian, M L; Leith, D W G S; Libby, J; Luitz, S; Lüth, V; Lynch, H L; Marsiske, H; Messner, R; Müller, D R; O'Grady, C P; Ozcan, V E; Perazzo, A; Perl, M; Petrak, S; Ratcliff, B N; Roodman, A; Salnikov, A A; Schindler, R H; Schwiening, J; Simi, G; Snyder, A; Soha, A; Stelzer, J; Su, D; Sullivan, M K; Vavra, J; Wagner, S R; Weaver, M; Weinstein, A J R; Wisniewski, W J; Wittgen, M; Wright, D H; Yarritu, A K; Young, C C; Burchat, Patricia R; Edwards, A J; Meyer, T I; Petersen, B A; Roat, C; Ahmed, S; Alam, M S; Ernst, J A; Saeed, M A; Saleem, M; Wappler, F R; Bugg, W; Krishnamurthy, M; Spanier, S M; Eckmann, R; Kim, H; Ritchie, J L; Satpathy, A; Schwitters, R F; Izen, J M; Kitayama, I; Lou, X C; Ye, S; Bianchi, F; Bóna, M; Gallo, F; Gamba, D; Bosisio, L; Cartaro, C; Cossutti, F; Della Ricca, G; Dittongo, S; Grancagnolo, S; Lanceri, L; Poropat, P; Vuagnin, G; Panvini, R S; Banerjee, Sw; Brown, C M; Fortin, D; Jackson, P D; Kowalewski, R V; Roney, J M; Sobie, R J; Band, H R; Cheng, B; Dasu, S; Datta, M; Eichenbaum, A M; Graham, M; Hollar, J J; Johnson, J R; Kutter, P E; Li, H; Liu, R; Mihályi, A; Mohapatra, A K; Pan, Y; Prepost, R; Tan, P; Von Wimmersperg-Töller, J H; Wu, J; Wu, S L; Yu, Z; Greene, M G; Neal, H

    2004-01-01

    We present a study of the decays B0bar --> D(*)0 K(*)0bar using a sample of 124 million Upsilon(4S) --> B0bar B0 decays collected with the BaBar detector at the PEP-II asymmetric-energy e+e- collider at SLAC. We report evidence for the decay of B0 and B0bar mesons to the D*0 K_S final state with an average branching fraction BF(B --> D*0 K0bar) = (4.5 +/- 1.9 +/- 0.5) x 10^-5. Similarly, we measure BF(B --> D0 K0bar) = (6.2 +/- 1.2 +/- 0.4) x 10^-5 for the D0 K_S final state. We also measure BF(B0bar --> D0 K*0bar) = (6.2 +/- 1.4 +/- 0.6) x 10^-5 and set a 90% C.L. upper limit BF(B0bar --> D0bar K*0bar) < 4.1 x 10^-5. All results presented in this paper are preliminary.

  17. Orbital Support of Fast and Slow Inner Bars in Double Barred Galaxies

    CERN Document Server

    Maciejewski, Witold

    2010-01-01

    We analyze how the orbital support of the inner bar in a double-barred galaxy (nested bars) depends on the angular velocity (i.e. pattern speed) of this bar. We study orbits in seven models of double bars using the method of invariant loops. The range of pattern speed is covered exhaustively. We find that not all pattern speeds are allowed when the inner bar rotates in the same direction as the outer bar. Below a certain minimum pattern speed orbital support for the inner bar abruptly disappears, while at high values of this speed the orbits indicate an increasingly round bar that looks more like a twist in the nuclear isophotes than a dynamically independent component. For values between these two extremes, orbits supporting the inner bar extend further out as the bar's pattern speed decreases, their corresponding loops become more eccentric, pulsate more, and their rotation becomes increasingly non-uniform, as they speed up and slow down in their motion. Lower pattern speeds also lead to a less coherent bar...

  18. Too Much Bar and Not Enough Mitzvah? A Proposed Research Agenda on Bar/Bat Mitzvah

    Science.gov (United States)

    Schoenfeld, Stuart

    2010-01-01

    Jewish educators are understandably interested in research on how bar/bat mitzvah affect Jewish education or research on what Jewish schools have done to avoid the distortions of a focus on bar/bat mitzvah. Research might also focus on the somewhat different and more ambitious topic of the role that bar/bat mitzvah play in contemporary Jewish…

  19. Test of bar window with internal bars free from the glass surfaces

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe

    1998-01-01

    A sealed glazing unit with 3 horisontal and 3 vertical bars and a reference glazing without bars have been tested in a guarded hotbox. The difference in measured heat loss coefficient between the two test objects is a measure of the thermal influence of the bars. The difference in heat loss...

  20. On the Relation between Spector's Bar Recursion and Modified Bar Recursion

    DEFF Research Database (Denmark)

    Oliva, Paulo Borges

    2002-01-01

    We introduce a variant of Spector's Bar Recursion in finite types to give a realizability interpretation of the classical axiom of dependent choice allowing for the extraction of witnesses from proofs of Sigma_1 formulas in classical analysis. We also give a bar recursive definition of the fan...... functional and study the relationship of our variant of Bar Recursion with others....

  1. Tubular stabilizer bars – calculations and construction

    Directory of Open Access Journals (Sweden)

    Adam-Markus WITTEK

    2011-01-01

    Full Text Available The article outlines the calculation methods for tubular stabilizer bars. Modern technological and structural solutions in contemporary cars are reflected also in the construction, selection and manufacturing of tubular stabilizer bars. A proper construction and the selection of parameters influence the strength properties, the weight, durability and reliability as well as the selection of an appropriate production method.

  2. Stabilizer bars: Part 1. Calculations and construction

    Directory of Open Access Journals (Sweden)

    Adam-Markus WITTEK

    2010-01-01

    Full Text Available The article outlines the calculation methods for stabilizer bars. Modern technological and structural solutions in contemporary cars are reflected also in the construction and manufacturing of stabilizer bars. A proper construction and the selection of parameters influence the strength properties, the weight, durability and reliability as well as the selection of an appropriate production method.

  3. The Bar Tack Machine. Module 16.

    Science.gov (United States)

    South Carolina State Dept. of Education, Columbia. Office of Vocational Education.

    This module on the bar tack machine, one in a series dealing with industrial sewing machines, their attachments, and operation, covers one topic: performing special operations on the bar tack machine. These components are provided: an introduction, directions, an objective, learning activities, student information, a student self-check, and a…

  4. Bar Study Stories. Issues in Prevention

    Science.gov (United States)

    Higher Education Center for Alcohol, Drug Abuse, and Violence Prevention, 2012

    2012-01-01

    This issue of "Issues in Prevention" focuses on the impact of the availability of drinks in licensed establishments, such as bars and taverns on student drinking. This issue contains the following articles: (1) Cheap Drinks at College Bars Can Escalate Student Drinking (John D. Clapp); (2) High Alcohol Outlet Density: A Problem for Campuses and…

  5. Constraints from microlensing on the COBE bar

    Science.gov (United States)

    Zhao, H. S.

    Since the first review of converging evidences for a bar in the center of the Galaxy by de Zeeuw (1992) at the IAU Sym. 153 in Gent five years ago, the Galactic bar idea has been put on a solid footing by an influx of new data (COBE/DIRBE maps, star count data of bulge red clump giants, microlensing optical depth, and bulge stellar proper motions, etc.) and a burst of increasingly sophisticated theoretical models (triaxial luminosity models of Dwek et al. 1994, and Binney, Gerhard & Spergel 1997, steady state stellar bar dynamical model of Zhao 1996, combined luminosity, microlensing and gas kinematics models of Zhao, Rich & Spergel 1996, and Bissantz et al. 1997, etc.), which fit new data and improve upon earlier simple bulge/bar models (Kent 1992, Binney et al. 1991, Blitz & Spergel 1991). While research in this field shifts more and more to constraining the exact phase space and parameter space of the bar, both the non-uniqueness of and the mismatches among bars from different datasets start to show up. I compare the bar from microlensing data with the COBE bar and point out the effects the non-uniqueness.

  6. Pesticide Product Label System

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Pesticide Product Label System (PPLS) provides a collection of pesticide product labels (Adobe PDF format) that have been approved by EPA under Section 3 of the...

  7. Mental Labels and Tattoos

    Science.gov (United States)

    Hyatt, I. Ralph

    1977-01-01

    Discusses the ease with which mental labels become imprinted in our system, six basic axioms for maintaining negative mental tattoos, and psychological processes for eliminating mental tattoos and labels. (RK)

  8. Semiotic labelled deductive systems

    Energy Technology Data Exchange (ETDEWEB)

    Nossum, R.T. [Imperial College of Science, Technology and Medicine, London (United Kingdom)

    1996-12-31

    We review the class of Semiotic Models put forward by Pospelov, as well as the Labelled Deductive Systems developed by Gabbay, and construct an embedding of Semiotic Models into Labelled Deductive Systems.

  9. [Development of cereal bar with pineapple skin].

    Science.gov (United States)

    Fonseca, Renata Siqueira; Del Santo, Victor Rogério; Souza, Gilberto Batista de; Pereira, Cíntia Alessandra Matiucci

    2011-06-01

    The cereal bars are multi-component products consisting of cereals, dried fruit and syrup binder and may be added to the consumable parts of fruits and vegetables which usually are not exploited and have high nutritional value, thereby reducing food waste. It was developed a jam with pineapple skin, which it was utilized in 13.5% in the cereal bar formulation. The cereal bar was sensorial evaluated and had its centesimal and mineral composition determined. The new product achieved average of 8.3 for global impression using 9 points hedonic scale, 91% of acceptance rate and 67% of purchase intent. In this first use of pineapple skin jam as food ingredient it can be concluded that its aggregation in the cereal bar formula is feasible, making an accepted product with fibers, proteins and minerals, as an alternative to traditional cereal bars.

  10. A COMPLETE THREE-DIMENSIONAL FINITE ELEMENT ANALYSIS OF THE BAR-BAR TENSILE IMPACT APPARATUS

    Institute of Scientific and Technical Information of China (English)

    万华培; 汪洋; 夏源明

    2003-01-01

    A complete three-dimensional FEM model of the Bar-Bar Tensile Impact Apparatus (BTIA) is constructed, in which the slots in the bars and the glue layers between the bars and the flat-shaped specimen are included. For elastic-plastic specimen material, Ly12cz aluminum alloy, the process of tensile impact experiments is simulated and the matching relation between the specimen geometry and the bars is investigated. Based on the FEM analysis, an iterative method is proposed to design a reasonable specimen geometry for obtaining the true dynamic stress-strain relation for a certain specimen material.

  11. An analytical algorithm to determine allowable ampacities of horizontally installed rectangular bus bars

    Directory of Open Access Journals (Sweden)

    Klimenta Dardan O.

    2016-01-01

    Full Text Available The main objective of this paper is to propose an algorithm for the determination of the allowable ampacities of single rectangular-section bus bars without the occurrence of correction factors. Without correction factors, the ampacity computation of the copper and aluminium bus bars is fully automatized. The analytical algorithm has been implemented in a computer program code that along with the allowable ampacity can compute the bus bar temperature and the individual heat transfer coefficient for each side of the bus bar, as well as their corresponding power losses. Natural and forced convection correlations for rectangular bus bars are applied. Effects of the solar radiation and radiation heat losses from the bus bar surface are taken into consideration as well. The finite element method (FEM has been used for the linear/non-linear steady-state thermal analysis, i.e. for validation of the analytical algorithm. All FEM-based numerical computations were carried out using the COMSOL Heat Transfer Module. [Projekat Ministarstva nauke Republike Srbije, br. TR33046

  12. An Implementation of Bayesian Adaptive Regression Splines (BARS in C with S and R Wrappers

    Directory of Open Access Journals (Sweden)

    Garrick Wallstrom

    2007-02-01

    Full Text Available BARS (DiMatteo, Genovese, and Kass 2001 uses the powerful reversible-jump MCMC engine to perform spline-based generalized nonparametric regression. It has been shown to work well in terms of having small mean-squared error in many examples (smaller than known competitors, as well as producing visually-appealing fits that are smooth (filtering out high-frequency noise while adapting to sudden changes (retaining high-frequency signal. However, BARS is computationally intensive. The original implementation in S was too slow to be practical in certain situations, and was found to handle some data sets incorrectly. We have implemented BARS in C for the normal and Poisson cases, the latter being important in neurophysiological and other point-process applications. The C implementation includes all needed subroutines for fitting Poisson regression, manipulating B-splines (using code created by Bates and Venables, and finding starting values for Poisson regression (using code for density estimation created by Kooperberg. The code utilizes only freely-available external libraries (LAPACK and BLAS and is otherwise self-contained. We have also provided wrappers so that BARS can be used easily within S or R.

  13. Speech coding

    Energy Technology Data Exchange (ETDEWEB)

    Ravishankar, C., Hughes Network Systems, Germantown, MD

    1998-05-08

    Speech is the predominant means of communication between human beings and since the invention of the telephone by Alexander Graham Bell in 1876, speech services have remained to be the core service in almost all telecommunication systems. Original analog methods of telephony had the disadvantage of speech signal getting corrupted by noise, cross-talk and distortion Long haul transmissions which use repeaters to compensate for the loss in signal strength on transmission links also increase the associated noise and distortion. On the other hand digital transmission is relatively immune to noise, cross-talk and distortion primarily because of the capability to faithfully regenerate digital signal at each repeater purely based on a binary decision. Hence end-to-end performance of the digital link essentially becomes independent of the length and operating frequency bands of the link Hence from a transmission point of view digital transmission has been the preferred approach due to its higher immunity to noise. The need to carry digital speech became extremely important from a service provision point of view as well. Modem requirements have introduced the need for robust, flexible and secure services that can carry a multitude of signal types (such as voice, data and video) without a fundamental change in infrastructure. Such a requirement could not have been easily met without the advent of digital transmission systems, thereby requiring speech to be coded digitally. The term Speech Coding is often referred to techniques that represent or code speech signals either directly as a waveform or as a set of parameters by analyzing the speech signal. In either case, the codes are transmitted to the distant end where speech is reconstructed or synthesized using the received set of codes. A more generic term that is applicable to these techniques that is often interchangeably used with speech coding is the term voice coding. This term is more generic in the sense that the

  14. Structural Behavior of Concrete Beams Reinforced with Basalt Fiber Reinforced Polymer (BFRP) Bars

    Science.gov (United States)

    Ovitigala, Thilan

    The main challenge for civil engineers is to provide sustainable, environmentally friendly and financially feasible structures to the society. Finding new materials such as fiber reinforced polymer (FRP) material that can fulfill the above requirements is a must. FRP material was expensive and it was limited to niche markets such as space shuttles and air industry in the 1960s. Over the time, it became cheaper and spread to other industries such as sporting goods in the 1980-1990, and then towards the infrastructure industry. Design and construction guidelines are available for carbon fiber reinforced polymer (CFRP), aramid fiber reinforced polymer (AFRP) and glass fiber reinforced polymer (GFRP) and they are currently used in structural applications. Since FRP is linear elastic brittle material, design guidelines for the steel reinforcement are not valid for FRP materials. Corrosion of steel reinforcement affects the durability of the concrete structures. FRP reinforcement is identified as an alternative to steel reinforcement in corrosive environments. Although basalt fiber reinforced polymer (BFRP) has many advantages over other FRP materials, but limited studies have been done. These studies didn't include larger BFRP bar diameters that are mostly used in practice. Therefore, larger beam sizes with larger BFRP reinforcement bar diameters are needed to investigate the flexural and shear behavior of BFRP reinforced concrete beams. Also, shear behavior of BFRP reinforced concrete beams was not yet studied. Experimental testing of mechanical properties and bond strength of BFRP bars and flexural and shear behavior of BFRP reinforced concrete beams are needed to include BFRP reinforcement bars in the design codes. This study mainly focuses on the use of BFRP bars as internal reinforcement. The test results of the mechanical properties of BFRP reinforcement bars, the bond strength of BFRP reinforcement bars, and the flexural and shear behavior of concrete beams

  15. $\\bar K$-Nuclear Deeply Bound States?

    CERN Document Server

    Gal, A

    2006-01-01

    Following the prediction by Akaishi and Yamazaki of relatively narrow $\\bar K$-nuclear states, deeply bound by over 100 MeV where the main decay channel $\\bar K N \\to \\pi \\Sigma$ is closed, several experimental signals in stopped $K^-$ reactions on light nuclei have been interpreted recently as due to such states. In this talk I review (i) the evidence from $K^-$-atom data for a {\\it deep} $\\bar K$-nucleus potential, as attractive as $V_{\\bar K}(\\rho_0) \\sim -(150 - 200)$ MeV at nuclear matter density, that could support such states; and (ii) the theoretical arguments for a {\\it shallow} potential, $V_{\\bar K}(\\rho_0) \\sim -(40 - 60)$ MeV. I then review a recent work by Mare\\v{s}, Friedman and Gal in which $\\bar K$-nuclear bound states are generated dynamically across the periodic table, using a RMF Lagrangian that couples the $\\bar K$ to the scalar and vector meson fields mediating the nuclear interactions. Substantial polarization of the core nucleus is found for light nuclei, with central nuclear densities...

  16. NGC 4340 Double Bar + Fossil Nuclear Ring

    CERN Document Server

    Erwin, P; Beckman, J E

    2000-01-01

    NGC 4340 is a double-barred SB0 galaxy in the Virgo cluster (Wozniak et al. 1995, A&AS 111, 115). Here, we show that this galaxy also posseses a luminous stellar nuclear ring of relatively old stars with little or no gas. The ring lies just outside the inner bar, at the probable inner inner Lindblad resonance (IILR) of the outer bar. Careful inspection of the isophotes and unsharp masks shows that the two bars are slightly misaligned, which suggests they may be independently rotating. The bright nuclear ring distorts the isophotes and ellipse fits and is most clearly seen in the unsharp mask (an inner bar also visible). B-R color maps show no features associated with the ring: it is the same color as the surrounding bulge, and thus probably an old, ``fossil'' remnant of an earlier star-formation episode. We use Simien & Prugniel's (1997, A&AS 126, 15) major-axis velocities to compute resonance curves; we use our spectrum along the outer-bar major axis to estimate that bar's pattern speed. The Omeg...

  17. Impact resistance of bar glasses.

    Science.gov (United States)

    Shepherd, J P; Huggett, R H; Kidner, G

    1993-12-01

    Bar glasses are often used as weapons in interpersonal violence. Violence often erupts spontaneously and assailants use objects close to hand as weapons. After an initial national Accident and Emergency Department study to identify glass designs most often implicated in interpersonal violence, the impact resistance of 1-pint beer glasses was tested in a materials laboratory with a Zwick 5102 pendulum impact tester. Both straight-sided (nonik) glasses (annealed and tempered) and handled tankards (annealed) were tested to destruction. The impact resistance of new glasses was compared with that of glasses subjected to wear. The mean impact resistance of new annealed noniks did not differ significantly although new glasses were significantly more resistant than worn glasses (p shards although the thicker bases remained intact. The mean impact resistance of new annealed noniks was 0.5 J, of worn annealed noniks 0.08 J, of tempered new noniks > 4 J, of worn tempered noniks 0.18 J, and of tankards, 1.7 J.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:8263994

  18. Speaking Code

    DEFF Research Database (Denmark)

    Cox, Geoff

    development, Speaking Code unfolds an argument to undermine the distinctions between criticism and practice, and to emphasize the aesthetic and political aspects of software studies. Not reducible to its functional aspects, program code mirrors the instability inherent in the relationship of speech......; alternatives to mainstream development, from performances of the live-coding scene to the organizational forms of commons-based peer production; the democratic promise of social media and their paradoxical role in suppressing political expression; and the market’s emptying out of possibilities for free...... expression in the public realm. The book’s line of argument defends language against its invasion by economics, arguing that speech continues to underscore the human condition, however paradoxical this may seem in an era of pervasive computing....

  19. Star Formation Properties in Barred Galaxies(SFB). III. Statistical Study of Bar-driven Secular Evolution using a sample of nearby barred spirals

    CERN Document Server

    Zhou, Zhi-Min; Wu, Hong

    2014-01-01

    Stellar bars are important internal drivers of secular evolution in disk galaxies. Using a sample of nearby spiral galaxies with weak and strong bars, we explore the relationships between the star formation feature and stellar bars in galaxies. We find that galaxies with weak bars tend to be coincide with low concentrical star formation activity, while those with strong bars show a large scatter in the distribution of star formation activity. We find enhanced star formation activity in bulges towards stronger bars, although not predominantly, consistent with previous studies. Our results suggest that different stages of the secular process and many other factors may contribute to the complexity of the secular evolution. In addition, barred galaxies with intense star formation in bars tend to have active star formation in their bulges and disks, and bulges have higher star formation densities than bars and disks, indicating the evolutionary effects of bars. We then derived a possible criterion to quantify the ...

  20. Tidally Induced Bars of Galaxies in Clusters

    Science.gov (United States)

    Łokas, Ewa L.; Ebrová, Ivana; del Pino, Andrés; Sybilska, Agnieszka; Athanassoula, E.; Semczuk, Marcin; Gajda, Grzegorz; Fouquet, Sylvain

    2016-08-01

    Using N-body simulations, we study the formation and evolution of tidally induced bars in disky galaxies in clusters. Our progenitor is a massive, late-type galaxy similar to the Milky Way, composed of an exponential disk and a Navarro-Frenk-White dark matter halo. We place the galaxy on four different orbits in a Virgo-like cluster and evolve it for 10 Gyr. As a reference case, we also evolve the same model in isolation. Tidally induced bars form on all orbits soon after the first pericenter passage and survive until the end of the evolution. They appear earlier, are stronger and longer, and have lower pattern speeds for tighter orbits. Only for the tightest orbit are the properties of the bar controlled by the orientation of the tidal torque from the cluster at pericenter. The mechanism behind the formation of the bars is the angular momentum transfer from the galaxy stellar component to its halo. All of the bars undergo extended periods of buckling instability that occur earlier and lead to more pronounced boxy/peanut shapes when the tidal forces are stronger. Using all simulation outputs of galaxies at different evolutionary stages, we construct a toy model of the galaxy population in the cluster and measure the average bar strength and bar fraction as a function of clustercentric radius. Both are found to be mildly decreasing functions of radius. We conclude that tidal forces can trigger bar formation in cluster cores, but not in the outskirts, and thus can cause larger concentrations of barred galaxies toward the cluster center.

  1. Study of the charmed baryonic decays $\\bar{B}^0\\to\\Sigma_{\\mathrm{c}}^{++}\\bar{p}\\pi^-$ and $\\bar{B}^0\\to\\Sigma_{\\mathrm{c}}^{0}\\bar{p}\\pi^+$

    CERN Document Server

    Abe, K; Aihara, H; Anipko, D; Aoki, K; Arakawa, T; Arinstein, K; Asano, Y; Aso, T; Aulchenko, V M; Aushev, T; Aziz, T; Bahinipati, S; Bakich, A M; Balagura, V; Ban, Y; Banerjee, S; Barberio, E; Barbero, M; Bay, A; Bedny, I; Belous, K S; Bitenc, U; Bizjak, I; Blyth, S; Bondar, A; Bozek, A; Bracko, M; Brodzicka, J; Browder, T E; Chang, M C; Chang, P; Chao, Y; Chen, A; Chen, K F; Chen, W T; Cheon, B G; Chistov, R; Choi, J H; Choi, S K; Choi, Y; Choi, Y K; Chuvikov, A; Cole, S; Dalseno, J; Danilov, M; Dash, M; Dowd, R; Dragic, J; Drutskoy, A; Eidelman, S; Enari, Y; Epifanov, D A; Fratina, S; Fujii, H; Fujikawa, M; Gabyshev, N; Garmash, A; Gershon, T; Go, A; Gokhroo, G; Goldenzweig, P; Golob, B; Gorisek, A; Grosse-Perdekamp, M; Guler, H; Ha, H; Haba, J; Hara, K; Hara, T; Hasegawa, Y; Hastings, N C; Hayasaka, K; Hayashii, H; Hazumi, M; Heffernan, D; Higuchi, T; Hinz, L; Hokuue, T; Hoshi, Y; Hoshina, K; Hou, S; Hou, W S; Hsiung, Y B; Igarashi, Y; Iijima, T; Ikado, K; Imoto, A; Inami, K; Ishikawa, A; Ishino, H; Itoh, K; Itoh, R; Iwabuchi, M; Iwasaki, M; Iwasaki, Y; Jacoby, C; Jones, M; Kakuno, H; Kang, J H; Kang, J S; Kapusta, P; Kataoka, S U; Katayama, N; Kawai, H; Kawasaki, T; Khan, H R; Kibayashi, A; Kichimi, H; Kikuchi, N; Kim, H J; Kim, H O; Kim, J H; Kim, S K; Kim, T H; Kim, Y J; Kinoshita, K; Kishimoto, N; Korpar, S; Kozakai, Y; Krizan, P; Krokovnyi, P P; Kubota, T; Kulasiri, R; Kumar, R; Kuo, C C; Kurihara, E; Kusaka, A; Kuzmin, A; Kwon, Y J; Lange, J S; Leder, G; Lee, J; Lee, S E; Lee, Y J; Lesiak, T; Li, J; Limosani, A; Lin, C Y; Lin, S W; Liu, Y; Liventsev, D; MacNaughton, J; Majumder, G; Mandl, F; Marlow, D; Matsumoto, T; Matyja, A; McOnie, S; Medvedeva, T; Mikami, Y; Mitaroff, W A; Miyabayashi, K; Miyake, H; Miyata, H; Miyazaki, Y; Mizuk, R; Mohapatra, D; Moloney, G R; Mori, T; Müller, J; Murakami, A; Nagamine, T; Nagasaka, Y; Nakagawa, T; Nakahama, Y; Nakamura, I; Nakano, E; Nakao, M; Nakazawa, H; Natkaniec, Z; Neichi, K; Nishida, S; Nishimura, K; Nitoh, O; Noguchi, S; Nozaki, T; Ogawa, A; Ogawa, S; Ohshima, T; Okabe, T; Okuno, S; Olsen, S L; Ono, S; Ostrowicz, W; Ozaki, H; Pakhlov, P; Pakhlova, G; Palka, H; Park, C W; Park, H; Park, K S; Parslow, N; Peak, L S; Pernicka, M; Pestotnik, R; Peters, M; Piilonen, L E; Poluektov, A; Ronga, F J; Root, N; Rorie, J; Rózanska, M; Sahoo, H; Saitoh, S; Sakai, Y; Sakamoto, H; Sakaue, H; Sarangi, T R; Sato, N; Satoyama, N; Sayeed, K; Schietinger, T; Schneider, O; Schonmeier, P; Schümann, J; Schwanda, C; Schwartz, A J; Seidl, R; Seki, T; Senyo, K; Sevior, M E; Shapkin, M; Shen, Y T; Shibuya, H; Shwartz, B; Sidorov, V; Singh, J B; Sokolov, A; Somov, A; Soni, N; Stamen, R; Stanic, S; Staric, M; Stöck, H; Sugiyama, A; Sumisawa, K; Sumiyoshi, T; Suzuki, S; Suzuki, S Y; Tajima, O; Takada, N; Takasaki, F; Tamai, K; Tamura, N; Tanaka, M; Taylor, G N; Teramoto, Y; Tian, X C; Tikhomirov, I; Trabelsi, K; Tsai, Y T; Tse, Y F; Tsuboyama, T; Tsukamoto, T; Uchida, K; Uchida, Y; Uehara, S; Uglov, T; Ueno, K; Unno, Y; Uno, S; Urquijo, P; Ushiroda, Y; Usov, Yu; Varner, G; Varvell, K E; Villa, S; Wang, C C; Wang, C H; Wang, M Z; Watanabe, M; Watanabe, Y; Wicht, J; Widhalm, L; Wiechczynski, J; Won, E; Wu, C H; Xie, Q L; Yabsley, B D; Yamaguchi, A; Yamamoto, H; Yamamoto, S; Yamashita, Y; Yamauchi, M; Heyoung Yang; Yoshino, S; Yuan, Y; Yusa, Y; Zang, S L; Zhang, C C; Zhang, J; Zhang, L M; Zhang, Z P; Zhilich, V; Ziegler, T; Zupanc, A; Zürcher, D

    2006-01-01

    We study the three-body charmed baryonic decays $\\bar{B}^0\\to\\Sigma_{\\mathrm{c}}^{++}\\bar{p}\\pi^-$ and $\\bar{B}^0\\to\\Sigma_{\\mathrm{c}}^{0}\\bar{p}\\pi^+$ in the four-body final state $\\bar{B}^0\\to\\Lambda_{\\mathrm{c}}^{+}\\bar{p}\\pi^+\\pi^-$, based on a data sample of 357 fb$^{-1}$ accumulated at the $\\Upsilon(4S)$ with the Belle detector at the KEKB asymmetric $e^+e^-$ collider. We measure branching fractions: ${\\cal B} (\\bar{B}^0\\to\\Sigma_{\\mathrm{c}}(2455)^{++}\\bar{p}\\pi^-)$=(\

  2. First Measurement of σ(gg → t$\\bar{t}$)/σ(p$\\bar{p}$ → t$\\bar{t}$)

    Energy Technology Data Exchange (ETDEWEB)

    Alamdari, Shabnaz Pashapour [Univ. of Toronto, ON (Canada)

    2008-01-01

    The work presented here is the first measurement of the fraction of top quark pair production through gluon-gluon fusion. We use an integrated luminosity of 0.96 ± 0.06 fb-1 of p{bar p} collisions at √s of 1.96 TeV collected by the CDF II detector. We select t$\\bar{t}$ candidates by identifying a high-pT lepton candidate, a large missing ET as evidence for a neutrino candidate and at least four high ET jets, one of which has to be identified as originating from a b quark. The challenge is to discriminate between the two production processes with the identical final state, gg → t$\\bar{t}$ and q$\\bar{p}$ → t$\\bar{t}$. We take advantage of the fact that compared to a quark, a gluon is more likely to radiate a low momentum gluon and therefore, one expects a larger number of charged particles with low pT in a process involving more gluons. Given the large uncertainties associated with the modeling of the low pT charged particle multiplicity, a data-driven technique was employed. Using calibration data samples, we show there exists a clear correlation between the observed average number of low pT charged particles and the average number of gluons involved in the production process predicted by Monte Carlo calculations. Given the correlation, one can identify low pT charged particle multiplicity distributions associated with specific average number of gluons. The W + 0 jet sample and dijets sample with leading jet ET in the range of 80-100 GeV are used to find no-gluon and gluon-rich low p{sub T} charged particle multiplicity distributions, respectively. Using these no-gluon and gluon-rich distributions in a likelihood fit, we find the fraction of gluon-rich events in t{bar t} candidates. This fraction has contributions from the signal and background events. Taking into account these contributions and the gg → t$\\bar{t}$ and q$\\bar{q}$ → t$\\bar

  3. The Aster code; Code Aster

    Energy Technology Data Exchange (ETDEWEB)

    Delbecq, J.M

    1999-07-01

    The Aster code is a 2D or 3D finite-element calculation code for structures developed by the R and D direction of Electricite de France (EdF). This dossier presents a complete overview of the characteristics and uses of the Aster code: introduction of version 4; the context of Aster (organisation of the code development, versions, systems and interfaces, development tools, quality assurance, independent validation); static mechanics (linear thermo-elasticity, Euler buckling, cables, Zarka-Casier method); non-linear mechanics (materials behaviour, big deformations, specific loads, unloading and loss of load proportionality indicators, global algorithm, contact and friction); rupture mechanics (G energy restitution level, restitution level in thermo-elasto-plasticity, 3D local energy restitution level, KI and KII stress intensity factors, calculation of limit loads for structures), specific treatments (fatigue, rupture, wear, error estimation); meshes and models (mesh generation, modeling, loads and boundary conditions, links between different modeling processes, resolution of linear systems, display of results etc..); vibration mechanics (modal and harmonic analysis, dynamics with shocks, direct transient dynamics, seismic analysis and aleatory dynamics, non-linear dynamics, dynamical sub-structuring); fluid-structure interactions (internal acoustics, mass, rigidity and damping); linear and non-linear thermal analysis; steels and metal industry (structure transformations); coupled problems (internal chaining, internal thermo-hydro-mechanical coupling, chaining with other codes); products and services. (J.S.)

  4. Possible $D\\bar{D}$ and $B\\bar{B}$ Molecular states in a chiral quark model

    CERN Document Server

    Li, M T; Dong, Y B; Zhang, Z Y

    2012-01-01

    We perform a systematic study of the bound state problem of $D\\bar{D}$ and $B\\bar{B}$ systems by using effective interaction in our chiral quark model. Our results show that both the interactions of $D\\bar{D}$ and $B\\bar{B}$ states are attractive, which consequently result in $I^G(J^{PC})=0^+(0^{++})$ $D\\bar{D}$ and $B\\bar{B}$ bound states.

  5. Optimal codes as Tanner codes with cyclic component codes

    DEFF Research Database (Denmark)

    Høholdt, Tom; Pinero, Fernando; Zeng, Peng

    2014-01-01

    In this article we study a class of graph codes with cyclic code component codes as affine variety codes. Within this class of Tanner codes we find some optimal binary codes. We use a particular subgraph of the point-line incidence plane of A(2,q) as the Tanner graph, and we are able to describe...... the codes succinctly using Gröbner bases....

  6. MCNP code

    International Nuclear Information System (INIS)

    The MCNP code is the major Monte Carlo coupled neutron-photon transport research tool at the Los Alamos National Laboratory, and it represents the most extensive Monte Carlo development program in the United States which is available in the public domain. The present code is the direct descendent of the original Monte Carlo work of Fermi, von Neumaum, and Ulam at Los Alamos in the 1940s. Development has continued uninterrupted since that time, and the current version of MCNP (or its predecessors) has always included state-of-the-art methods in the Monte Carlo simulation of radiation transport, basic cross section data, geometry capability, variance reduction, and estimation procedures. The authors of the present code have oriented its development toward general user application. The documentation, though extensive, is presented in a clear and simple manner with many examples, illustrations, and sample problems. In addition to providing the desired results, the output listings give a a wealth of detailed information (some optional) concerning each state of the calculation. The code system is continually updated to take advantage of advances in computer hardware and software, including interactive modes of operation, diagnostic interrupts and restarts, and a variety of graphical and video aids

  7. ANIMAL code

    International Nuclear Information System (INIS)

    This report describes ANIMAL, a two-dimensional Eulerian magnetohydrodynamic computer code. ANIMAL's physical model also appears. Formulated are temporal and spatial finite-difference equations in a manner that facilitates implementation of the algorithm. Outlined are the functions of the algorithm's FORTRAN subroutines and variables

  8. Blast Quantification Using Hopkinson Pressure Bars.

    Science.gov (United States)

    Clarke, Samuel D; Fay, Stephen D; Rigby, Samuel E; Tyas, Andrew; Warren, James A; Reay, Jonathan J; Fuller, Benjamin J; Gant, Matthew T A; Elgy, Ian D

    2016-07-05

    Near-field blast load measurement presents an issue to many sensor types as they must endure very aggressive environments and be able to measure pressures up to many hundreds of megapascals. In this respect the simplicity of the Hopkinson pressure bar has a major advantage in that while the measurement end of the Hopkinson bar can endure and be exposed to harsh conditions, the strain gauge mounted to the bar can be affixed some distance away. This allows protective housings to be utilized which protect the strain gauge but do not interfere with the measurement acquisition. The use of an array of pressure bars allows the pressure-time histories at discrete known points to be measured. This article also describes the interpolation routine used to derive pressure-time histories at un-instrumented locations on the plane of interest. Currently the technique has been used to measure loading from high explosives in free air and buried shallowly in various soils.

  9. ${{\\bar{d}} - {\\bar{u}}}$ Flavor Asymmetry in the Proton in Chiral Effective Field Theory

    Energy Technology Data Exchange (ETDEWEB)

    Salamu, Y. [Institute of High Energy Physics, CAS, Beijing, 100049, China; Ji, Cheung-Ryong [North Carolina State University, Raleigh, NC; Melnitchouk, Wally [Jefferson Lab, Newport News, VA; Wang, P. [Theoretical Physics Center for Science Facilities, CAS, Beijing, 100049, China

    2015-09-01

    The ${\\bar d - \\bar u}$ flavor asymmetry in the proton arising from pion loops is computed using chiral effective field theory. The calculation includes both nucleon and Δ intermediate states, and uses both the fully relativistic and heavy baryon frameworks. The x dependence of ${\\bar d - \\bar u}$ extracted from the Fermilab E866 Drell–Yan data can be well reproduced in terms of a single transverse momentum cutoff parameter regulating the ultraviolet behavior of the loop integrals. In addition to the distribution at x > 0, corrections to the integrated asymmetry from zero momentum contributions are computed, which arise from pion rainbow and bubble diagrams at x = 0. These have not been accounted for in previous analyses, and can make important contributions to the lowest moment of ${\\bar d-\\bar u}$ .

  10. Intelligent bar chart plagiarism detection in documents.

    Science.gov (United States)

    Al-Dabbagh, Mohammed Mumtaz; Salim, Naomie; Rehman, Amjad; Alkawaz, Mohammed Hazim; Saba, Tanzila; Al-Rodhaan, Mznah; Al-Dhelaan, Abdullah

    2014-01-01

    This paper presents a novel features mining approach from documents that could not be mined via optical character recognition (OCR). By identifying the intimate relationship between the text and graphical components, the proposed technique pulls out the Start, End, and Exact values for each bar. Furthermore, the word 2-gram and Euclidean distance methods are used to accurately detect and determine plagiarism in bar charts.

  11. The DIRC detector at BaBar

    International Nuclear Information System (INIS)

    A dedicated particle identification system based on the Detection of Internally Reflected Cherenkov (DIRC) light will be used in the BaBar detector. We provide an overview of the DIRC concept, design, and expected performance of the production device and a status report on its construction and commissioning. The DIRC is expected to be operating in the BaBar detector on beam line at the PEP-II B Factory in late spring 1999

  12. Chocolate Bars Based on Human Nutritional Requirements

    OpenAIRE

    Robson, Anthony

    2013-01-01

    International audience Key Points * The nutritional value of chocolate bars should be based on the nutritional value of the low energy dense late Paleolithic human diet to help reduce mental ill health, obesity, and other postprandial insults. * Current chocolate bars have a high energy density (>2 kcal/g). * Cocoa can be sweetened by the addition of calorie-free Purefruit™ (Tate & Lyle) monk fruit ( Siraitia grosvenorii ) extract. PUREFRUIT™ is approximately 200 times sweeter than sugar a...

  13. The empirical research of consumers purchase behavior for labeled with trace code pork---case of two pilot cities of Hefei and Wuhu in Anhui%消费者对加贴追溯码猪肉购买意愿的实证研究--以合肥、芜湖两个试点城市为例

    Institute of Scientific and Technical Information of China (English)

    赵仁芳; 李丽; 陶善信

    2016-01-01

    基于肉菜流通追溯体系下安徽两个试点城市的278份调查数据,利用Logistic模型分析了消费者对加贴追溯码猪肉的购买意愿。在已有研究基础上,增加了消费者的食品安全事件经历、对肉菜流通追溯体系的认知度、对肉菜流通追溯体系的评价和对食品安全法规政策的认知度4个新解释变量。结果表明,上述4个新变量以及消费者对加贴追溯码猪肉的认知度和信任程度、家庭最高文化程度及收支状况等对购买意愿具有显著正向影响;消费者对食品安全状况评价、对猪肉质量安全现状评价和年龄等则对购买意愿具有显著负向影响。%Based on the meat and vegetable circulation tracing system and 278 consumer questionnaires’ survey data of two pilot cities in Anhui province, using logistic model, this article analyzed consumers buying behavior for labeled with trace code pork. On the basis of existing research, this article increased four new explanatory variables. The results showed that the above four new variables and consumer′s recognition and trust for labeled with trace code pork, the highest family degree of culture, and the balance of payments had significant positive influence on purchase behavior;Consumer's evaluation about the situation of food safety, consumer status evaluation for pork quality and safety and age had significant reverse influence on purchase behavior.

  14. The Influence of Bars on Nuclear Activity

    CERN Document Server

    Ho, L C; Sargent, W L W; Ho, Luis C.; Filippenko, Alexei V.; Sargent, Wallace L. W.

    1997-01-01

    We test ideas on fueling of galactic nuclei by bar-driven inflow by comparing the detection rate and intensity of nuclear H II regions and AGNs among barred and unbarred galaxies in a sample of over 300 spirals selected from our recent optical spectroscopic survey of nearby galaxies. Among late-type spirals (Sc-Sm), but not early-type (S0/a-Sbc), we observe in the barred group a very marginal increase in the detection rate of H II nuclei and a corresponding decrease in the incidence of AGNs. The minor differences in the detection rates, however, are statistically insignificant, most likely stemming from selection effects and not from a genuine influence from the bar. The presence of a bar seems to have no noticeable impact on the likelihood of a galaxy to host either nuclear star formation or an AGN. The nuclei of early-type barred spirals do exhibit measurably higher star-formation rates than their unbarred counterparts, as indicated by either the luminosity or the equivalent width of H-alpha emission. By co...

  15. Hot Disks And Delayed Bar Formation

    CERN Document Server

    Sheth, Kartik; Elmegreen, Debra Meloy; Elmegreen, Bruce G; Athanassoula, E; Weiner, Ben

    2012-01-01

    We present observational evidence for the inhibition of bar formation in dispersion-dominated (dynamically hot) galaxies by studying the relationship between galactic structure and host galaxy kinematics in a sample of 257 galaxies between 0.1 $<$ z $\\leq$ 0.84 from the All-Wavelength Extended Groth Strip International Survey (AEGIS) and the Deep Extragalactic Evolutionary Probe 2 (DEEP2) survey. We find that bars are preferentially found in galaxies that are massive and dynamically cold (rotation-dominated) and on the stellar Tully-Fisher relationship, as is the case for barred spirals in the local Universe. The data provide at least one explanation for the steep ($\\times$3) decline in the overall bar fraction from z=0 to z=0.84 in L$^*$ and brighter disks seen in previous studies. The decline in the bar fraction at high redshift is almost exclusively in the lower mass (10 $<$ log M$_{*}$(\\Msun)$<$ 11), later-type and bluer galaxies. A proposed explanation for this "downsizing" of the bar formation ...

  16. Labelling Fashion Markets

    OpenAIRE

    Aspers, P.

    2008-01-01

    The present article discusses how an ethical and environmental labelling system can be implemented in fashion garment markets. Consumers act in markets that provide them with more information than their limited cognitive capacity allows them to handle. Ethical and environmental labelling in markets characterized by change, such as the fashion garment market, makes decision-making even more complicated. The ethical and environmental labelling system proposed here is designed to alleviate firms...

  17. Deuterium labeled cannabinoids

    International Nuclear Information System (INIS)

    Complex reactions involving ring opening, ring closure and rearrangements hamper complete understanding of the fragmentation processes in the mass spectrometric fragmentation patterns of cannabinoids. Specifically labelled compounds are very powerful tools for obtaining more insight into fragmentation mechanisms and ion structures and therefore the synthesis of specifically deuterated cannabinoids was undertaken. For this, it was necessary to investigate the preparation of cannabinoids, appropriately functionalized for specific introduction of deuterium atom labels. The results of mass spectrometry with these labelled cannabinoids are described. (Auth.)

  18. Possible Signatures of New Physics in e+e- and bar bar{p}p Collisions

    Science.gov (United States)

    Senju, H.

    1998-12-01

    A preon model with preonic charge predicts many unique new particles. Among them, several are expected to be relatively light, including the fermion lS, which is a stable WIMP, bosons U0 and U+ and the lepto-quark fermion q'. The production of these particles in e+e- and bar{p}p collisions is discussed, focusing on e+e- --> UlS(e) and bar{p}p --> bar{q}'q' + X. A signature of the latter is dilepton + 2 charm jets + missing energy. A discussion on reported unusual events in the dilepton + jets sample is made based on bar{q}'q' production.

  19. $\\bar d - \\bar u$ asymmetry in the proton in chiral effective theory

    Energy Technology Data Exchange (ETDEWEB)

    Salamu, Yusupujiang [Institute of High Energy Physics, CAS, Beijing (China); Ji, Chueng -Ryong [North Carolina State Univ., Raleigh, NC (United States); Melnitchouk, W. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Wang, P. [Institute of High Energy Physics, Beijing (China); Theoretical Physics Center for Science Facilities, CAS, Beijing (China)

    2015-03-25

    We compute the $\\bar d - \\bar u$ asymmetry in the proton in chiral effective theory, including both nucleon and Δ degrees of freedom, within both relativistic and heavy baryon frameworks. In addition to the distribution at $x>0$, we estimate the correction to the integrated asymmetry arising from zero momentum contributions from pion rainbow and bubble diagrams at $x=0$, which have not been accounted for in previous analyses. In conclusion, we find that the empirical $x$ dependence of $\\bar d - \\bar u$ as well as the integrated asymmetry can be well reproduced in terms of a transverse momentum cutoff parameter.

  20. Discriminative sparse coding on multi-manifolds

    KAUST Repository

    Wang, J.J.-Y.

    2013-09-26

    Sparse coding has been popularly used as an effective data representation method in various applications, such as computer vision, medical imaging and bioinformatics. However, the conventional sparse coding algorithms and their manifold-regularized variants (graph sparse coding and Laplacian sparse coding), learn codebooks and codes in an unsupervised manner and neglect class information that is available in the training set. To address this problem, we propose a novel discriminative sparse coding method based on multi-manifolds, that learns discriminative class-conditioned codebooks and sparse codes from both data feature spaces and class labels. First, the entire training set is partitioned into multiple manifolds according to the class labels. Then, we formulate the sparse coding as a manifold-manifold matching problem and learn class-conditioned codebooks and codes to maximize the manifold margins of different classes. Lastly, we present a data sample-manifold matching-based strategy to classify the unlabeled data samples. Experimental results on somatic mutations identification and breast tumor classification based on ultrasonic images demonstrate the efficacy of the proposed data representation and classification approach. 2013 The Authors. All rights reserved.

  1. Cultural Factors Related to Smoking in San Francisco's Irish Bars

    Science.gov (United States)

    Satterlund, Travis D.; Antin, Tamar M. J.; Lee, Juliet P.; Moore, Roland S.

    2009-01-01

    California's Smoke-Free Workplace Act was extended to include bars in 1998. While the majority of bars in the state have become smoke free, in many bars patrons and staff continue to smoke despite the law. The authors present findings from a study which assessed cultural factors related to continued smoking in bars in the city of San Francisco. In…

  2. 21 CFR 886.1650 - Ophthalmic bar prism.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic bar prism. 886.1650 Section 886.1650...) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1650 Ophthalmic bar prism. (a) Identification. An ophthalmic bar prism is a device that is a bar composed of fused prisms of gradually...

  3. Branching fractions for chi_cJ -> p p-bar pi^0, p p-bar eta, and p p-bar omega

    CERN Document Server

    Onyisi, P U E; Alexander, J P; Cassel, D G; Das, S; Ehrlich, R; Fields, L; Gibbons, L; Gray, S W; Hartill, D L; Heltsley, B K; Hunt, J M; Kreinick, D L; Kuznetsov, V E; Ledoux, J; Patterson, J R; Peterson, D; Riley, D; Ryd, A; Sadoff, A J; Shi, X; Sun, W M; Yelton, J; Rubin, P; Lowrey, N; Mehrabyan, S; Selen, M; Wiss, J; Adams, S; Kornicer, M; Mitchell, R E; Shepherd, M R; Tarbert, C M; Besson, D; Pedlar, T K; Xavier, J; Cronin-Hennessy, D; Hietala, J; Zweber, P; Dobbs, S; Metreveli, Z; Seth, K K; Xiao, T; Tomaradze, A; Brisbane, S; Libby, J; Martin, L; Powell, A; Spradlin, P; Wilkinson, G; Mendez, H; Ge, J Y; Miller, D H; Shipsey, I P J; Xin, B; Adams, G S; Hu, D; Moziak, B; Napolitano, J; Ecklund, K M; Insler, J; Muramatsu, H; Park, C S; Thorndike, E H; Yang, F; Ricciardi, S; Thomas, C; Artuso, M; Blusk, S; Mountain, R; Skwarnicki, T; Stone, S; Wang, J C; Zhang, L M; Bonvicini, G; Cinabro, D; Lincoln, A; Smith, M J; Zhou, P; Zhu, J; Naik, P; Rademacker, J; Asner, D M; Edwards, K W; Reed, J; Randrianarivony, K; Robichaud, A N; Tatishvili, G; White, E J; Briere, R A; Vogel, H

    2010-01-01

    Using a sample of 25.9 million psi(2S) decays acquired with the CLEO-c detector at the CESR e^+e^- collider, we report branching fractions for the decays chi_cJ -> p p-bar pi^0, p p-bar eta, and p p-bar omega, with J=0,1,2. Our results for B(chi_cJ-> p p-bar pi^0) and B(chi_cJ-> p p-bar eta) are consistent with, but more precise than, previous measurements. Furthermore, we include the first measurement of B(chi_cJ-> p p-bar omega).

  4. Halo evolution in the presence of a disc bar

    CERN Document Server

    McMillan, P J; Millan, Paul J. Mc; Dehnen, Walter

    2005-01-01

    Angular momentum transfer from a rotating stellar bar has been proposed by Weinberg & Katz (2002) as a mechanism to destroy dark-matter cusps in a few rotation periods. The N-body simulations performed by these authors in support of their claim employed spherical harmonics for the force computation and were, as shown by Sellwood (2003), very sensitive to inclusion of asymmetric terms (odd l,m). In order to disentangle possible numerical artifacts due to the usage of spherical harmonics from genuine stellar dynamical effects, we performed similar experiments using a tree code and find that significant cusp destruction requires substantially more angular momentum than is realistically available. However, we find that the simplified model (a N-body halo torqued by a rotating bar pinned to the origin) undergoes an instability in which the cusp moves away from the origin. In presence of this off-centring, spherical density profiles centred on the origin display an apparent cusp-removal. We strongly suspect tha...

  5. Evidence for the existence of $u d \\bar{b} \\bar{b}$ and the non-existence of $s s \\bar{b} \\bar{b}$ and $c c \\bar{b} \\bar{b}$ tetraquarks from lattice QCD

    CERN Document Server

    Bicudo, Pedro; Peters, Antje; Wagenbach, Björn; Wagner, Marc

    2015-01-01

    We combine lattice QCD results for the potential of two static antiquarks in the presence of two quarks $q q$ of finite mass and quark model techniques to study possibly existing $q q \\bar{b} \\bar{b}$ tetraquarks. While there is strong indication for a bound four-quark state for $q q = (ud-du) / \\sqrt{2}$, i.e. isospin $I=0$, we find clear evidence against the existence of corresponding tetraquarks with $q q \\in \\{ uu , (ud+du) / \\sqrt{2} , dd \\}$, i.e. isospin $I=1$, $q q = s s$ and $q q = c c$.

  6. Stable isotopes labelled compounds

    International Nuclear Information System (INIS)

    The catalogue on stable isotopes labelled compounds offers deuterium, nitrogen-15, and multiply labelled compounds. It includes: (1) conditions of sale and delivery, (2) the application of stable isotopes, (3) technical information, (4) product specifications, and (5) the complete delivery programme

  7. NOVEL BIPHASE CODE -INTEGRATED SIDELOBE SUPPRESSION CODE

    Institute of Scientific and Technical Information of China (English)

    Wang Feixue; Ou Gang; Zhuang Zhaowen

    2004-01-01

    A kind of novel binary phase code named sidelobe suppression code is proposed in this paper. It is defined to be the code whose corresponding optimal sidelobe suppression filter outputs the minimum sidelobes. It is shown that there do exist sidelobe suppression codes better than the conventional optimal codes-Barker codes. For example, the sidelobe suppression code of length 11 with filter of length 39 has better sidelobe level up to 17dB than that of Barker code with the same code length and filter length.

  8. Label Fusion Strategy Selection

    Directory of Open Access Journals (Sweden)

    Nicolas Robitaille

    2012-01-01

    Full Text Available Label fusion is used in medical image segmentation to combine several different labels of the same entity into a single discrete label, potentially more accurate, with respect to the exact, sought segmentation, than the best input element. Using simulated data, we compared three existing label fusion techniques—STAPLE, Voting, and Shape-Based Averaging (SBA—and observed that none could be considered superior depending on the dissimilarity between the input elements. We thus developed an empirical, hybrid technique called SVS, which selects the most appropriate technique to apply based on this dissimilarity. We evaluated the label fusion strategies on two- and three-dimensional simulated data and showed that SVS is superior to any of the three existing methods examined. On real data, we used SVS to perform fusions of 10 segmentations of the hippocampus and amygdala in 78 subjects from the ICBM dataset. SVS selected SBA in almost all cases, which was the most appropriate method overall.

  9. From concatenated codes to graph codes

    DEFF Research Database (Denmark)

    Justesen, Jørn; Høholdt, Tom

    2004-01-01

    We consider codes based on simple bipartite expander graphs. These codes may be seen as the first step leading from product type concatenated codes to more complex graph codes. We emphasize constructions of specific codes of realistic lengths, and study the details of decoding by message passing...... in trees....

  10. Concatenated codes with convolutional inner codes

    DEFF Research Database (Denmark)

    Justesen, Jørn; Thommesen, Christian; Zyablov, Viktor

    1988-01-01

    The minimum distance of concatenated codes with Reed-Solomon outer codes and convolutional inner codes is studied. For suitable combinations of parameters the minimum distance can be lower-bounded by the product of the minimum distances of the inner and outer codes. For a randomized ensemble of...... concatenated codes a lower bound of the Gilbert-Varshamov type is proved...

  11. Radioiodine and its labelled compounds

    International Nuclear Information System (INIS)

    Chemical characteristics and their nuclear characteristics, types of labelled molecules,labelling procedures, direct labelling with various oxidizing agents, indirect labelling with various conjugates attached to protein molecules, purification and quality control. Iodination damage.Safe handling of labelling procedures with iodine radioisotopes.Bibliography

  12. Warp evidences in precessing galactic bar models

    CERN Document Server

    Sanchez-Martin, Patricia; Masdemont, Josep J

    2016-01-01

    Most galaxies have a warped shape when they are seen from an edge-on point of view. The reason for this curious form is not completely known so far and in this work we apply dynamical system tools to contribute to its explanation. Starting from a simple, but realistic, model formed by a bar and a disc, we study the effect produced by a small misalignment between the angular momentum of the system and its angular velocity. To this end, a precession model is developed and considered, assuming that the bar behaves like a rigid body. After checking that the periodic orbits inside the bar keep being the skeleton of the inner system, even after inflicting a precession to the potential, we compute the invariant manifolds of the unstable periodic orbits departing from the equilibrium points at the ends of the bar to get evidences of their warped shapes. As it is well known, the invariant manifolds associated with these periodic orbits drive the arms and rings of barred galaxies and constitute the skeleton of these bu...

  13. Tidally induced bars of galaxies in clusters

    CERN Document Server

    Lokas, Ewa L; del Pino, Andres; Sybilska, Agnieszka; Athanassoula, E; Semczuk, Marcin; Gajda, Grzegorz; Fouquet, Sylvain

    2016-01-01

    Using N-body simulations we study the formation and evolution of tidally induced bars in disky galaxies in clusters. Our progenitor is a massive, late-type galaxy similar to the Milky Way, composed of an exponential disk and an NFW dark matter halo. We place the galaxy on four different orbits in a Virgo-like cluster and evolve it for 10 Gyr. As a reference case we also evolve the same model in isolation. Tidally induced bars form on all orbits soon after the first pericenter passage and survive until the end of the evolution. They appear earlier, are stronger, longer and have lower pattern speeds for tighter orbits. Only for the tightest orbit the properties of the bar are controlled by the orientation of the tidal torque from the cluster at pericenters. The mechanism behind the formation of the bars is the angular momentum transfer from the galaxy stellar component to its halo. All bars undergo extended periods of buckling instability that occur earlier and lead to more pronounced boxy/peanut shapes when th...

  14. Warp evidence in precessing galactic bar models

    Science.gov (United States)

    Sánchez-Martín, P.; Romero-Gómez, M.; Masdemont, J. J.

    2016-04-01

    Most galaxies have a warped shape when they are seen edge-on. The reason for this curious form is not completely known so far, so in this work we apply dynamical system tools to contribute to its explanation. Starting from a simple, but realistic model formed by a bar and a disc, we study the effect of a small misalignment between the angular momentum of the system and its angular velocity. To this end, a precession model was developed and considered, assuming that the bar behaves like a rigid body. After checking that the periodic orbits inside the bar continue to be the skeleton of the inner system even after inflicting a precession to the potential, we computed the invariant manifolds of the unstable periodic orbits departing from the equilibrium points at the ends of the bar to find evidence of their warped shapes. As is well known, the invariant manifolds associated with these periodic orbits drive the arms and rings of barred galaxies and constitute the skeleton of these building blocks. Looking at them from a side-on viewpoint, we find that these manifolds present warped shapes like those recognised in observations. Lastly, test particle simulations have been performed to determine how the stars are affected by the applied precession, this way confirming the theoretical results.

  15. CP Asymmetries in bar B -> bar K* (-> bar K pi) l+ l- and Untagged bar B_s,B_s -> phi (-> K+ K-) l+ l- Decays at NLO

    CERN Document Server

    Bobeth, Christoph; Piranishvili, Giorgi

    2008-01-01

    The decay bar B -> bar K* (-> bar K pi) l+ l- offers great opportunities to explore the physics at and above the electroweak scale by means of an angular analysis. We investigate the physics potential of the seven CP asymmetries plus the asymmetry in the rate, working at low dilepton mass using QCD factorization at next-to leading order (NLO). The b ->s CP asymmetries are doubly Cabibbo-suppressed \\lesssim 1 % in the Standard Model and its extensions where the CKM matrix is the only source of CP violation. Three CP asymmetries are T-odd, and can be O(1) in the presence of non-standard CP violation. The T-even asymmetries can reach O(0.1), limited by the small strong phases in the large recoil region. We furthermore point out an easy way to measure CP phases from time-integrated, untagged bar B_d, B_d -> K* (-> K0 pi0) l+ l- and bar B_s,B_s -> phi (-> K+ K-) l+ l- decays. Analyses of these CP asymmetries can rule out, or further support the minimal description of CP violation through the CKM mechanism. Experim...

  16. Assessing attentional prioritization of front-of-pack nutrition labels using change detection.

    Science.gov (United States)

    Becker, Mark W; Sundar, Raghav Prashant; Bello, Nora; Alzahabi, Reem; Weatherspoon, Lorraine; Bix, Laura

    2016-05-01

    We used a change detection method to evaluate attentional prioritization of nutrition information that appears in the traditional "Nutrition Facts Panel" and in front-of-pack nutrition labels. Results provide compelling evidence that front-of-pack labels attract attention more readily than the Nutrition Facts Panel, even when participants are not specifically tasked with searching for nutrition information. Further, color-coding the relative nutritional value of key nutrients within the front-of-pack label resulted in increased attentional prioritization of nutrition information, but coding using facial icons did not significantly increase attention to the label. Finally, the general pattern of attentional prioritization across front-of-pack designs was consistent across a diverse sample of participants. Our results indicate that color-coded, front-of-pack nutrition labels increase attention to the nutrition information of packaged food, a finding that has implications for current policy discussions regarding labeling change. PMID:26851468

  17. Quantum Cyclic Code

    CERN Document Server

    Dutta, Sagarmoy

    2010-01-01

    In this paper, we define and study \\emph{quantum cyclic codes}, a generalisation of cyclic codes to the quantum setting. Previously studied examples of quantum cyclic codes were all quantum codes obtained from classical cyclic codes via the CSS construction. However, the codes that we study are much more general. In particular, we construct cyclic stabiliser codes with parameters $[[5,1,3

  18. Does green mean healthy? Nutrition label color affects perceptions of healthfulness.

    Science.gov (United States)

    Schuldt, Jonathon P

    2013-01-01

    The food industry has recently implemented numerous front-of-package nutrition labels to readily convey key aspects a food product's nutritional profile to consumers (e.g., calories and fat content). Although seemingly well-intentioned, such labels might lead consumers to perceive relatively poor nutrition foods in a healthier light. The present research explores whether one underresearched aspect of nutrition labels-namely, their color-might influence perceptions of a product's healthfulness. In Study 1, participants perceived a candy bar as healthier when it bore a green rather than a red calorie label, despite the fact that the labels conveyed the same calorie content. Study 2 examined the perceived healthfulness of a candy bar bearing a green versus white calorie label and assessed individual differences in the importance of healthy eating. Overall, results suggest that green labels increase perceived healthfulness, especially among consumers who place high importance on healthy eating. Discussion focuses on implications for health-related judgment and nutrition labeling.

  19. Nutrition Facts: Reading the Label

    Science.gov (United States)

    ... My Go4Life Get Free Stuff Be a Partner Nutrition Facts: Reading the Label Reading labels can help ... of information on their labels or packaging about nutrition and food safety. Product dates . You might see ...

  20. DATA SECURITY THROUGH QR CODE ENCRYPTION AND STEGANOGRAPHY

    OpenAIRE

    M. Mary Shanthi Rani; K.Rosemary Euphrasia

    2016-01-01

    The art of information hiding has become an important issue in the recent years as security of information has become a big concern in this internet era. Cryptography and Steganography play major role for secured data transfer. Steganography stands for concealed writing; it hides the message inside a cover medium. Cryptography conceals the content of a message by encryption. QR (Quick Response) Codes are 2-dimensional bar codes that encode text strings. They are able to encode inf...

  1. Jazz Chants Born in a Piano Bar

    Directory of Open Access Journals (Sweden)

    Caroline Graham

    2010-01-01

    Full Text Available When I first arrived in New York in the late sixties, I began teaching ESL at New York University. I didn`t really think of teaching as a profession for me. I just thought it would pay the rent so I could do what I really wanted to do which was to sing and play ragtime piano in the piano bars. When I got my first piano job in an Irish Bar it was uptown, far away from NYU so I didn`t feel it was necessary to mention this night job to my boss.

  2. Newtorites in bar detectors of gravitational wave

    CERN Document Server

    Ronga, F

    2015-01-01

    The detection of particles with only gravitational interactions (Newtorites) in gravitational bar detectors was studied in 1984 by Bernard, De Rujula and Lautrup. The negative results of dark matter searches suggest to look to exotic possibilities like Newtorites. The limits obtained with the Nautilus bar detector will be presented and the possible improvements will be discussed. Since the gravitational coupling is very weak, the possible limits are very far from what is needed for dark matter, but for large masses are the best limits obtained on the Earth. An update of limits for MACRO particles will be given.

  3. Sine-Bar Attachment For Machine Tools

    Science.gov (United States)

    Mann, Franklin D.

    1988-01-01

    Sine-bar attachment for collets, spindles, and chucks helps machinists set up quickly for precise angular cuts that require greater precision than provided by graduations of machine tools. Machinist uses attachment to index head, carriage of milling machine or lathe relative to table or turning axis of tool. Attachment accurate to 1 minute or arc depending on length of sine bar and precision of gauge blocks in setup. Attachment installs quickly and easily on almost any type of lathe or mill. Requires no special clamps or fixtures, and eliminates many trial-and-error measurements. More stable than improvised setups and not jarred out of position readily.

  4. Track Finding Efficiency in BaBar

    CERN Document Server

    Allmendinger, T; Brown, D N; Choi, H; Christ, S; Covarelli, R; Davier, M; Denig, A G; Fritsch, M; Hafner, A; Kowalewski, R; Long, O; Lutz, A M; Martinelli, M; Muller, D R; Nugent, I M; Pegna, D Lopes; Purohit, M V; Prencipe, E; Roney, J M; Simi, G; Solodov, E P; Telnov, A V; Varnes, E; Waldi, R; Wang, W F; White, R M

    2012-01-01

    We describe several studies to measure the charged track reconstruction efficiency and asymmetry of the BaBar detector. The first two studies measure the tracking efficiency of a charged particle using $\\tau$ and initial state radiation decays. The third uses the $\\tau$ decays to study the asymmetry in tracking, the fourth measures the tracking efficiency for low momentum tracks, and the last measures the reconstruction efficiency of $K_S^0$ particles. The first section also examines the stability of the measurements vs BaBar running periods.

  5. The Disability Dilemma: A Skeptical Bench & Bar

    OpenAIRE

    Wendy F. Hensel

    2008-01-01

    The legal profession is no stranger to the bias and prejudice present in American society. Members of the bar have been shown to engage in both conscious and subconscious sexism and racism, posing challenges to the profession as the profile of those practicing law has changed over the last several decades to admit increasing numbers of women and minorities.1 Nevertheless, it is notable that few, if any, members of the bar today would question openly whether women or people of color have the a...

  6. B Counting at BaBar

    Energy Technology Data Exchange (ETDEWEB)

    McGregor, Grant Duncan

    2008-12-16

    In this thesis we examine the method of counting B{bar B} events produced in the BABAR experiment. The original method was proposed in 2000, but improvements to track reconstruction and our understanding of the detector since that date make it appropriate to revisit the B Counting method. We propose a new set of cuts designed to minimize the sensitivity to time-varying backgrounds. We find the new method counts B{bar B} events with an associated systematic uncertainty of {+-} 0.6%.

  7. Imaging of physeal bars in children

    Energy Technology Data Exchange (ETDEWEB)

    Wang, David C. [Massachusetts General Hospital and Harvard Medical School, Department of Radiology, Boston, MA (United States); Deeney, Vincent; Roach, James W. [Children' s Hospital of Pittsburgh of UPMC, Department of Orthopedics, Pittsburgh, PA (United States); Shah, Amisha J. [Children' s Hospital of Pittsburgh of UPMC, Department of Radiology, Pittsburgh, PA (United States)

    2015-08-15

    The growth plate, also known as the physis or epiphyseal plate, is essential for longitudinal growth of bones in the immature skeleton. A variety of insults to the growth plate from trauma to infection to idiopathic causes can lead to physeal bar formation, an interruption in normal growth plate cartilage, where a bony or fibrous bridge develops between the metaphysis and epiphysis. This bridge restricts subsequent bone growth, leading to limb shortening and/or angular deformities. Early recognition of the presence of a physeal bar can help direct appropriate surgical management to restore linear growth of the bone. (orig.)

  8. M33: THE EXISTENCE OF A BAR

    Directory of Open Access Journals (Sweden)

    I. Hernández-López

    2009-01-01

    Full Text Available A signi cant fraction of galaxies in the Local Universe classi ed as unbarred in the RC3 turn out to be barred in optical and NIR wavelengths. In the Local Group the Milky Way and M31 have shown to be barred as well, this also could be the case of M33. In this paper we present the results of the Ellipse tting and bidimensional Fourier Analysis, on the R and I bands, deprojected and non-deprojected, images of M33 obtained from DSS2 and Spitzer-IRAC.

  9. From Label to Practice

    DEFF Research Database (Denmark)

    Byrkjeflot, Haldor; Strandgaard, Jesper; Svejenova, Silviya

    2013-01-01

    This article examines the process of creation of new Nordic cuisine (NNC) as a culinary innovation, focusing on the main stages, actors, and mechanisms that shaped the new label and its practices and facilitated its diffusion in the region and internationally. Fast-paced diffusion was possible...... because NNC was conceived as an identity movement, triggered by active involvement of entrepreneurial leaders from the culinary profession, high-profile political supporters, legitimating scientists, disseminating media, and interpreting audiences. It was facilitated by three mechanisms: First, the use...... actors and institutions to develop practices associated with the NNC label. Third, organized dissemination allowed the excitement and engagement with the new label to spread quickly....

  10. Forming Double-barred Galaxies From Dynamically Cool Inner Disks

    CERN Document Server

    Du, Min; Debattista, Victor P

    2015-01-01

    About one third of early-type barred galaxies host small-scale secondary bars. The formation and evolution of such double-barred galaxies remain far from being well understood. In order to understand the formation of such systems, we explore a large parameter space of isolated pure-disk simulations. We show that a dynamically cool inner disk embedded in a hotter outer disk can naturally generate a steady secondary bar while the outer disk forms a large-scale primary bar. The independent bar instabilities of inner and outer disks result in long-lived double-barred structures whose dynamical properties are comparable with observations. This formation scenario indicates that the secondary bar might form from the general bar instability, the same as the primary bar. Under some circumstances, the interaction of the bars and the disk leads to the two bars aligning or single, nuclear, bars only. Simulations that are cool enough of the center to experience clump instabilities may also generate steady double-barred ga...

  11. Observation of B+ --> K0bar K+ and B0 --> K0 K0bar

    CERN Document Server

    Aubert, B; Boutigny, D; Couderc, F; Karyotakis, Yu; Lees, J P; Poireau, V; Tisserand, V; Zghiche, A; Graugès-Pous, E; Palano, A; Chen, J C; Qi, N D; Rong, G; Wang, P; Zhu, Y S; Eigen, G; Ofte, I; Stugu, B; Abrams, G S; Battaglia, M; Brown, D N; Button-Shafer, J; Cahn, R N; Charles, E; Gill, M S; Groysman, Y; Jacobsen, R G; Kadyk, J A; Kerth, L T; Kolomensky, Yu G; Kukartsev, G; Lynch, G; Mir, L M; Orimoto, T J; Pripstein, M; Roe, N A; Ronan, M T; Wenzel, W A; Del, P; Amo Sanchez; Barrett, M; Ford, K E; Harrison, T J; Hart, A J; Hawkes, C M; Watson, A T; Held, T; Koch, H; Lewandowski, B; Pelizaeus, M; Peters, K; Schröder, T; Steinke, M; Boyd, J T; Burke, J P; Cottingham, W N; Walker, D; Asgeirsson, D J; Çuhadar-Dönszelmann, T; Fulsom, B G; Hearty, C; Knecht, N S; Mattison, T S; McKenna, J A; Khan, A; Kyberd, P; Saleem, M; Sherwood, D J; Teodorescu, L; Blinov, V E; Bukin, A D; Druzhinin, V P; Golubev, V B; Onuchin, A P; Serednyakov, S I; Skovpen, Yu I; Solodov, E P; Todyshev, K Yu; Bondioli, M; Bruinsma, M; Chao, M; Curry, S; Eschrich, I; Kirkby, D; Lankford, A J; Lund, P; Mandelkern, M A; Mommsen, R K; Röthel, W; Stoker, D P; Abachi, S; Buchanan, C; Foulkes, S D; Gary, J W; Long, O; Shen, B C; Wang, K; Zhang, L; Hadavand, H K; Hill, E J; Paar, H P; Rahatlou, S; Sharma, V; Berryhill, J W; Campagnari, C; Cunha, A; Dahmes, B; Hong, T M; Kovalskyi, D; Richman, J D; Beck, T W; Eisner, A M; Flacco, C J; Heusch, C A; Kroseberg, J; Lockman, W S; Nesom, G; Schalk, T; Schumm, B A; Seiden, A; Spradlin, P; Williams, D C; Wilson, M G; Albert, J; Chen, E; Dvoretskii, A; Fang, F; Hitlin, D G; Narsky, I; Piatenko, T; Porter, F C; Ryd, A; Mancinelli, G; Meadows, B T; Mishra, K; Sokoloff, M D; Blanc, F; Bloom, P C; Chen, S; Ford, W T; Hirschauer, J F; Kreisel, A; Nagel, M; Nauenberg, U; Olivas, A; Ruddick, W O; Smith, J G; Ulmer, K A; Wagner, S R; Zhang, J; Chen, A; Eckhart, E A; Soffer, A; Toki, W H; Wilson, R J; Winklmeier, F; Zeng, Q; Altenburg, D D; Feltresi, E; Hauke, A; Jasper, H; Merkel, J; Petzold, A; Spaan, B; Brandt, T; Klose, V; Lacker, H M; Mader, W F; Nogowski, R; Schubert, J; Schubert, K R; Schwierz, R; Sundermann, J E; Volk, A; Bernard, D; Bonneaud, G R; Latour, E; Thiebaux, C; Verderi, M; Clark, P J; Gradl, W; Muheim, F; Playfer, S; Robertson, A I; Xie, Y; Andreotti, M; Bettoni, D; Bozzi, C; Calabrese, R; Cibinetto, G; Luppi, E; Negrini, M; Petrella, A; Piemontese, L; Prencipe, E; Anulli, F; Baldini-Ferroli, R; Calcaterra, A; De Sangro, R; Finocchiaro, G; Pacetti, S; Patteri, P; Peruzzi, I M; Piccolo, M; Rama, M; Zallo, A; Buzzo, A; Contri, R; Lo, M; Lo Vetere, M; Macri, M M; Monge, M R; Passaggio, S; Patrignani, C; Robutti, E; Santroni, A; Tosi, S; Brandenburg, G; Chaisanguanthum, K S; Morii, M; Wu, J; Dubitzky, R S; Marks, J; Schenk, S; Uwer, U; Bard, D J; Bhimji, W; Bowerman, D A; Dauncey, P D; Egede, U; Flack, R L; Nash, J A; Nikolich, M B; Panduro-Vazquez, W; Behera, P K; Chai, X; Charles, M J; Mallik, U; Meyer, N T; Ziegler, V; Cochran, J; Crawley, H B; Dong, L; Eyges, V; Meyer, W T; Prell, S; Rosenberg, E I; Rubin, A E; Gritsan, A V; Denig, A G; Fritsch, M; Schott, G; Arnaud, N; Davier, M; Grosdidier, G; Höcker, A; Le Diberder, F R; Lepeltier, V; Lutz, A M; Oyanguren, A; Pruvot, S; Rodier, S; Roudeau, P; Schune, M H; Stocchi, A; Wang, W F; Wormser, G; Cheng, C H; Lange, D J; Wright, D M; Chavez, C A; Forster, I J; Fry, J R; Gabathuler, E; Gamet, R; George, K A; Hutchcroft, D E; Payne, D J; Schofield, K C; Touramanis, C; Bevan, A J; Di Lodovico, F; Menges, W; Sacco, R; Cowan, G; Flächer, H U; Hopkins, D A; Jackson, P S; McMahon, T R; Ricciardi, S; Salvatore, F; Wren, A C; Davis, C L; Allison, J; Barlow, N R; Barlow, R J; Chia, Y M; Edgar, C L; Lafferty, G D; Naisbit, M T; Williams, J C; Yi, J I; Chen, C; Hulsbergen, W D; Jawahery, A; Lae, C K; Roberts, D A; Simi, G; Blaylock, G; Dallapiccola, C; Hertzbach, S S; Li, X; Moore, T B; Saremi, S; Stängle, H; Cowan, R; Sciolla, G; Sekula, S J; Spitznagel, M; Taylor, F; Yamamoto, R K; Kim, H; Mclachlin, S E; Patel, P M; Robertson, S H; Lazzaro, A; Lombardo, V; Palombo, F; Bauer, J M; Cremaldi, L; Eschenburg, V; Godang, R; Kroeger, R; Sanders, D A; Summers, D J; Zhao, H W; Brunet, S; Côté, D; Simard, M; Taras, P; Viaud, F B; Nicholson, H; Cavallo, N; De Nardo, Gallieno; Fabozzi, F; Gatto, C; Lista, L; Monorchio, D; Paolucci, P; Piccolo, D; Sciacca, C; Baak, M A; Raven, G; Snoek, H L; Jessop, C P; LoSecco, J M; Allmendinger, T; Benelli, G; Corwin, L A; Gan, K K; Honscheid, K; Hufnagel, D; Jackson, P D; Kagan, H; Kass, R; Rahimi, A M; Regensburger, J J; Ter-Antonian, R; Wong, Q K; Blount, N L; Brau, J E; Frey, R; Igonkina, O; Kolb, J A; Lu, M; Rahmat, R; Sinev, N B; Strom, D; Strube, J; Torrence, E; Gaz, A; Margoni, M; Morandin, M; Pompili, A; Posocco, M; Rotondo, M; Simonetto, F; Stroili, R; Voci, C; Benayoun, M; Briand, H; Chauveau, J; David, P; Del, L; Buono; La Vaissière, C de; Hamon, O; Hartfiel, B L; Leruste, P; Malcles, J; Ocariz, J; Roos, L; Therin, G; Gladney, L; Biasini, M; Covarelli, R; Angelini, C; Batignani, G; Bettarini, S; Bucci, F; Calderini, G; Carpinelli, M; Cenci, R; Forti, F; Giorgi, M A; Lusiani, A; Marchiori, G; Mazur, M A; Morganti, M; Neri, N; Paoloni, E; Rizzo, G; Walsh, J J; Haire, M; Judd, D; Wagoner, D E; Biesiada, J; Danielson, N; Elmer, P; Lau, Y P; Lü, C; Olsen, J; Smith, A J S; Telnov, A V; Bellini, F; Cavoto, G; D'Orazio, A; Del Re, D; Di Marco, E; Faccini, R; Ferrarotto, F; Ferroni, F; Gaspero, M; Li Gioi, L; Mazzoni, M A; Morganti, S; Piredda, G; Polci, F; Safai-Tehrani, F; Voena, C; Ebert, M; Schröder, H; Waldi, R; Adye, T; De Groot, N; Franek, B; Olaiya, E O; Wilson, F F; Aleksan, R; Emery, S; Gaidot, A; Ganzhur, S F; Hamel de Monchenault, G; Kozanecki, Witold; Legendre, M; Vasseur, G; Yéche, C; Zito, M; Chen, X R; Liu, H; Park, W; Purohit, M V; Wilson, J R; Allen, M T; Aston, D; Bartoldus, R; Bechtle, P; Berger, N; Claus, R; Coleman, J P; Convery, M R; Cristinziani, M; Dingfelder, J C; Dorfan, J; Dubois-Felsmann, G P; Dujmic, D; Dunwoodie, W M; Field, R C; Glanzman, T; Gowdy, S J; Graham, M T; Grenier, P; Halyo, V; Hast, C; Hrynóva, T; Innes, W R; Kelsey, M H; Kim, P; Leith, D W G S; Li, S; Luitz, S; Lüth, V; Lynch, H L; MacFarlane, D B; Marsiske, H; Messner, R; Müller, D R; O'Grady, C P; Ozcan, V E; Perazzo, A; Perl, M; Pulliam, T; Ratcliff, B N; Roodman, A; Salnikov, A A; Schindler, R H; Schwiening, J; Snyder, A; Stelzer, J; Su, D; Sullivan, M K; Suzuki, K; Swain, S K; Thompson, J M; Vavra, J; Van Bakel, N; Weaver, M; Weinstein, A J R; Wisniewski, W J; Wittgen, M; Wright, D H; Yarritu, A K; Yi, K; Young, C C; Burchat, P R; Edwards, A J; Majewski, S A; Petersen, B A; Roat, C; Wilden, L; Ahmed, S; Alam, M S; Bula, R; Ernst, J A; Jain, V; Pan, B; Saeed, M A; Wappler, F R; Zain, S B; Bugg, W; Krishnamurthy, M; Spanier, S M; Eckmann, R; Ritchie, J L; Satpathy, A; Schilling, C J; Schwitters, R F; Izen, J M; Lou, X C; Ye, S; Bianchi, F; Gallo, F; Gamba, D; Bomben, M; Bosisio, L; Cartaro, C; Cossutti, F; Della Ricca, G; Dittongo, S; Lanceri, L; Vitale, L; Azzolini, V; Lopez-March, N; Martínez-Vidal, F; Banerjee, Sw; Bhuyan, B; Brown, C M; Fortin, D; Hamano, K; Kowalewski, R V; Nugent, I M; Roney, J M; Sobie, R J; Back, J J; Harrison, P F; Latham, T E; Mohanty, G B; Pappagallo, M; Band, H R; Chen, X; Cheng, B; Dasu, S; Datta, M; Flood, K T; Hollar, J J; Kutter, P E; Mellado, B; Mihályi, A; Pan, Y; Pierini, M; Prepost, R; Wu, S L; Yu, Z; Neal, H

    2006-01-01

    We report observations of the b --> d penguin-dominated decays B+ --> K0bar K+ and B0 --> K0 K0bar in approximately 350 million Upsilon(4S) --> BBbar decays collected with the BaBar detector. We measure the branching fractions B(B+ --> K0bar K+) = (1.61 +/- 0.44 +/- 0.09) * 10^-6 and B(B0 --> K0 K0bar) = (1.08 +/- 0.28 +/- 0.11) * 10^-6, and the CP-violating charge asymmetry A_{CP}(K0bar K+) = 0.10 +/- 0.26 +/- 0.03. Using a vertexing technique previously employed in several analyses of all-neutral final states containing kaons, we report the first measurement of time-dependent CP-violating asymmetries in B0 --> K0 K0bar, obtaining S = -1.28 +0.80/-0.73 +0.11/-0.16 and C = -0.40 +/- 0.41 +/- 0.06. We also report improved measurements of the branching fraction B(B0 --> K0 pi+) = (23.9 +/- 1.1 +/- 1.0) * 10^-6 and CP-violating charge asymmetry A_{CP}(K0 pi+) = -0.029 +/- 0.039 +/- 0.010.

  12. Clinical applications of cells labelling

    International Nuclear Information System (INIS)

    Blood cells labelled with radionuclides are reviewed and main applications are described. Red blood cell labelling by both random and specific principle. A table with most important clinical uses, 99mTc labelling of RBC are described pre tinning and in vivo reduction of Tc, in vitro labelling and administration of labelled RBC and in vivo modified technique. Labelled leucocytes with several 99mTc-complex radiopharmaceuticals by in vitro technique and specific monoclonal s for white cells(neutrofiles). Labelled platelets for clinical use and research by in vitro technique and in vivo labelling

  13. Parametric Study of Shear Strength of Concrete Beams Reinforced with FRP Bars

    Science.gov (United States)

    Thomas, Job; Ramadass, S.

    2016-06-01

    Fibre Reinforced Polymer (FRP) bars are being widely used as internal reinforcement in structural elements in the last decade. The corrosion resistance of FRP bars qualifies its use in severe and marine exposure conditions in structures. A total of eight concrete beams longitudinally reinforced with FRP bars were cast and tested over shear span to depth ratio of 0.5 and 1.75. The shear strength test data of 188 beams published in various literatures were also used. The model originally proposed by Indian Standard Code of practice for the prediction of shear strength of concrete beams reinforced with steel bars IS:456 (Plain and reinforced concrete, code of practice, fourth revision. Bureau of Indian Standards, New Delhi, 2000) is considered and a modification to account for the influence of the FRP bars is proposed based on regression analysis. Out of the 196 test data, 110 test data is used for the regression analysis and 86 test data is used for the validation of the model. In addition, the shear strength of 86 test data accounted for the validation is assessed using eleven models proposed by various researchers. The proposed model accounts for compressive strength of concrete (f ck ), modulus of elasticity of FRP rebar (E f ), longitudinal reinforcement ratio (ρ f ), shear span to depth ratio (a/d) and size effect of beams. The predicted shear strength of beams using the proposed model and 11 models proposed by other researchers is compared with the corresponding experimental results. The mean of predicted shear strength to the experimental shear strength for the 86 beams accounted for the validation of the proposed model is found to be 0.93. The result of the statistical analysis indicates that the prediction based on the proposed model corroborates with the corresponding experimental data.

  14. Like your labels?

    Science.gov (United States)

    Field, Michele

    2010-01-01

    The descriptive “conventions” used on food labels are always evolving. Today, however, the changes are so complicated (partly driven by legislation requiring disclosures about environmental impacts, health issues, and geographical provenance) that these labels more often baffle buyers than enlighten them. In a light-handed manner, the article points to how sometimes reading label language can be like deciphering runes—and how if we are familiar with the technical terms, we can find a literal meaning, but still not see the implications. The article could be ten times longer because food labels vary according to cultures—but all food-exporting cultures now take advantage of our short attention-span when faced with these texts. The question is whether less is more—and if so, in this contest for our attention, what “contestant” is voted off. PMID:21539053

  15. Succesful labelling schemes

    DEFF Research Database (Denmark)

    Juhl, Hans Jørn; Stacey, Julia

    2001-01-01

    labelling schemes. Mass communication such as TV commercials will have very different impact on each of the four segments. It might be possible to increase the knowledge of 'the labelling blind' from 52% to 75%, but the use of the label would only rise from 16% to 18%. The awareness percentage of 'the...... to carry out a campaign targeted at this segment. The awareness percentage is already 92 % and 67% of the respondents believe they know the meaning of the scheme. But it stands to reason to study whether the respondents actually know what the labelling scheme stands for or if they just think they do....... If there is discrepancy between their perceptions of the contents of the schemes, this might be the reason why the scheme is not observed when they shop....

  16. Behind the Label "Alcoholic."

    Science.gov (United States)

    Wright, Deborah M.

    1989-01-01

    Relates individual's personal story of her childhood influenced by her parent's alcoholism, her own alcoholism as a young adult, and her experiences with counseling. Asks others not to reject her because of the label "alcoholic." (ABL)

  17. FDA Online Label Repository

    Data.gov (United States)

    U.S. Department of Health & Human Services — The drug labels and other drug-specific information on this Web site represent the most recent drug listing information companies have submitted to the Food and...

  18. Certified Rule Labeling

    OpenAIRE

    Nagele, Julian; Zankl, Harald

    2015-01-01

    The rule labeling heuristic aims to establish confluence of (left-)linear term rewrite systems via decreasing diagrams. We present a formalization of a confluence criterion based on the interplay of relative termination and the rule labeling in the theorem prover Isabelle. Moreover, we report on the integration of this result into the certifier CeTA, facilitating the checking of confluence certificates based on decreasing diagrams for the first time. The power of the method is illustrated by ...

  19. Possible strange hidden-charm pentaquarks from $\\Sigma_c^{(*)}\\bar{D}_s^*$ and $\\Xi^{(',*)}_c\\bar{D}^*$ interactions

    CERN Document Server

    Chen, Rui; Liu, Xiang

    2016-01-01

    In a one-boson-exchange model with one-pion and one-eta exchanges, we investigate possible strange hidden-charm pentaquarks produced from the $\\Lambda_c\\bar{D}_s^*$, $\\Sigma_c\\bar{D}_s^*$, $\\Sigma_c^*\\bar{D}_s^*$, $\\Xi_c\\bar{D}^*$, $\\Xi_c'\\bar{D}^*$, and $\\Xi_c^*\\bar{D}^*$ interactions with the S-D wave mixing. The Lagrangians with chiral symmetry, heavy quark symmetry, and/or hidden local symmetry are adopted to describe the interactions. With such Lagrangians, it is found that the $\\Lambda_c\\bar{D}_s^*$ and $\\Xi_c\\bar{D}^*$ interactions are forbidden. For the $\\Sigma_c\\bar{D}_s^*$ and $\\Sigma_c^*\\bar{D}_s^*$ systems where the one-pion exchange is forbidden and only one-eta exchange survives, there exist three molecular candidates at cutoffs about 3 GeV, i.e., a $\\Sigma_c\\bar{D}_s^*$ state with quantum number $I(J^P)=1(\\frac{3}{2}^-)$ and $\\Sigma_c^*\\bar{D}_s^*$ states with $1(\\frac{1}{2}^-)$ and $1(\\frac{3}{2}^-)$. For the $\\Xi_c'\\bar{D}^*$ and $\\Xi_c^*\\bar{D}^*$ systems where the one-pion exchange is allow...

  20. Labelling of electricity

    International Nuclear Information System (INIS)

    This comprehensive report for the Swiss Federal Office of Energy (SFOE) presents a possible course of action to be taken to provide a means of declaring the sources of electrical power, as is foreseen in the draft of new Swiss electricity market legislation. The report presents the basic ideas behind the idea and defines the terms used such as labelling, certificates and declarations. Also, the legal situation in the European Union and in Switzerland is examined and a quantitative overview of electricity production and consumption is presented. Suggestions for a labelling scheme are made and some of the problems to be expected are looked at. The report also presents a series of examples of labelling schemes already implemented in other countries, such as Austria, Great Britain, Sweden and Germany. Tradable certificates and tracking systems are discussed as are initial quality labels like the Swiss 'Naturemade' label for green power. A concrete recommendation for the declaration and labelling of electricity in Switzerland is presented and various factors to be considered such as import/export, pumped storage, distribution losses, small-scale producers as well as the time-scales for introduction are discussed

  1. A piezo-bar pressure probe

    Science.gov (United States)

    Friend, W. H.; Murphy, C. L.; Shanfield, I.

    1967-01-01

    Piezo-bar pressure type probe measures the impact velocity or pressure of a moving debris cloud. It measures pressures up to 200,000 psi and peak pressures may be recorded with a total pulse duration between 5 and 65 musec.

  2. Bar instability in disk-halo systems

    CERN Document Server

    Sellwood, J A

    2016-01-01

    We show that the exponential growth rate of a bar in a stellar disk is substantially greater when the disk is embedded in a live halo than in a rigid one having the same mass distribution. We also find that the vigor of the instability in disk-halo systems varies with the shape of the halo velocity ellipsoid. Disks in rigid halos that are massive enough to be stable by the usual criteria, quickly form bars in isotropic halos and much greater halo mass is needed to avoid a strong bar; thus stability criteria derived for disks in rigid halos do not apply when the halo is responsive. The study presented here is of an idealized family of models with near uniform central rotation and that lack an extended halo; we present more realistic models with extended halos in a companion paper. The puzzle presented by the absence of strong bars in some galaxies having gently rising inner rotation curves is compounded by the results presented here.

  3. Blast Quantification Using Hopkinson Pressure Bars.

    Science.gov (United States)

    Clarke, Samuel D; Fay, Stephen D; Rigby, Samuel E; Tyas, Andrew; Warren, James A; Reay, Jonathan J; Fuller, Benjamin J; Gant, Matthew T A; Elgy, Ian D

    2016-01-01

    Near-field blast load measurement presents an issue to many sensor types as they must endure very aggressive environments and be able to measure pressures up to many hundreds of megapascals. In this respect the simplicity of the Hopkinson pressure bar has a major advantage in that while the measurement end of the Hopkinson bar can endure and be exposed to harsh conditions, the strain gauge mounted to the bar can be affixed some distance away. This allows protective housings to be utilized which protect the strain gauge but do not interfere with the measurement acquisition. The use of an array of pressure bars allows the pressure-time histories at discrete known points to be measured. This article also describes the interpolation routine used to derive pressure-time histories at un-instrumented locations on the plane of interest. Currently the technique has been used to measure loading from high explosives in free air and buried shallowly in various soils. PMID:27404117

  4. My Bar Graph Tells a Story

    Science.gov (United States)

    McMillen, Sue; McMillen, Beth

    2010-01-01

    Connecting stories to qualitative coordinate graphs has been suggested as an effective instructional strategy. Even students who are able to "create" bar graphs may struggle to correctly "interpret" them. Giving children opportunities to work with qualitative graphs can help them develop the skills to interpret, describe, and compare information…

  5. BaBar Explores CP Violation

    International Nuclear Information System (INIS)

    The most recent results obtained by the BABAR experiment at the PEP-II asymmetric-energy B Factory at SLAC on CP-violating asymmetries and branching fractions for neutral and charged B decays are presented here. The analysis was performed on a data sample of ∼ 88 million Υ(4S) → B(bar B) decays collected between 1999 and 2002. Using b → c(bar c)s decays, we measure sin2β = 0.741 ± 0.067(stat) ± 0.034(syst). We also present sin2β measurements from, b → s(bar s)s and b → c(bar c)d processes. From neutral B meson decays to two-body final states of charged pions and kaons, we derive for the CP violating parameters, Sππ = 0.02 ± 0.34 ± 0.05 [-0.54, +0.58] and Cππ = -0.30 ± 0.25 ± 0.04 [-0.72, +0.12]. First results for B → π+π-π0 and K±π±π0 final states dominated by the ρ± resonance, are also presented

  6. Star formation properties in barred galaxies. III. Statistical study of bar-driven secular evolution using a sample of nearby barred spirals

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Zhi-Min; Wu, Hong [Key Laboratory of Optical Astronomy, National Astronomical Observatories, Chinese Academy of Sciences, Beijing 100012 (China); Cao, Chen, E-mail: zmzhou@bao.ac.cn, E-mail: hwu@bao.ac.cn, E-mail: caochen@sdu.edu.cn [School of Space Science and Physics, Shandong University at Weihai, Weihai, Shandong 264209 (China)

    2015-01-01

    Stellar bars are important internal drivers of secular evolution in disk galaxies. Using a sample of nearby spiral galaxies with weak and strong bars, we explore the relationships between the star formation feature and stellar bars in galaxies. We find that galaxies with weak bars tend coincide with low concentrical star formation activity, while those with strong bars show a large scatter in the distribution of star formation activity. We find enhanced star formation activity in bulges toward stronger bars, although not predominantly, consistent with previous studies. Our results suggest that different stages of the secular process and many other factors may contribute to the complexity of the secular evolution. In addition, barred galaxies with intense star formation in bars tend to have active star formation in their bulges and disks, and bulges have higher star formation densities than bars and disks, indicating the evolutionary effects of bars. We then derived a possible criterion to quantify the different stages of the bar-driven physical process, while future work is needed because of the uncertainties.

  7. Search for the decay of a B0 or B0bar meson to K*0bar K0 or K*0 K0bar

    CERN Document Server

    Aubert, B; Bóna, M; Boutigny, D; Couderc, F; Karyotakis, Yu; Lees, J P; Poireau, V; Tisserand, V; Zghiche, A; Graugès-Pous, E; Palano, A; Chen, J C; Qi, N D; Rong, G; Wang, P; Zhu, Y S; Eigen, G; Ofte, I; Stugu, B; Abrams, G S; Battaglia, M; Brown, D N; Button-Shafer, J; Cahn, R N; Charles, E; Gill, M S; Groysman, Y; Jacobsen, R G; Kadyk, J A; Kerth, L T; Kolomensky, Yu G; Kukartsev, G; Lynch, G; Mir, L M; Oddone, P J; Orimoto, T J; Pripstein, M; Roe, N A; Ronan, M T; Wenzel, W A; Del Amo-Sánchez, P; Barrett, M; Ford, K E; Harrison, T J; Hart, A J; Hawkes, C M; Morgan, S E; Watson, A T; Goetzen, K; Held, T; Koch, H; Lewandowski, B; Pelizaeus, M; Peters, K; Schröder, T; Steinke, M; Boyd, J T; Burke, J P; Cottingham, W N; Walker, D; Çuhadar-Dönszelmann, T; Fulsom, B G; Hearty, C; Knecht, N S; Mattison, T S; McKenna, J A; Khan, A; Kyberd, P; Saleem, M; Sherwood, D J; Teodorescu, L; Blinov, V E; Bukin, A D; Druzhinin, V P; Golubev, V B; Onuchin, A P; Serednyakov, S I; Skovpen, Y I; Solodov, E P; Todyshev, K Y; Best, D S; Bondioli, M; Bruinsma, M; Chao, M; Curry, S; Eschrich, I; Kirkby, D; Lankford, A J; Lund, P; Mandelkern, M A; Mommsen, R K; Röthel, W; Stoker, D P; Abachi, S; Buchanan, C; Foulkes, S D; Gary, J W; Long, O; Shen, B C; Wang, K; Zhang, L; Hill, E J; Paar, H P; Rahatlou, S; Sharma, V; Berryhill, J W; Campagnari, C; Cunha, A; Dahmes, B; Hong, T M; Kovalskyi, D; Richman, J D; Beck, T W; Eisner, A M; Flacco, C J; Heusch, C A; Kroseberg, J; Lockman, W S; Nesom, G; Schalk, T; Schumm, B A; Seiden, A; Spradlin, P; Williams, D C; Wilson, M G; Albert, J; Chen, E; Dvoretskii, A; Hitlin, D G; Narsky, I; Piatenko, T; Porter, F C; Ryd, A; Samuel, A; Andreassen, R; Mancinelli, G; Meadows, B T; Sokoloff, M D; Blanc, F; Bloom, P C; Chen, S; Ford, W T; Hirschauer, J F; Kreisel, A; Nauenberg, U; Olivas, A; Ruddick, W O; Smith, J G; Ulmer, K A; Wagner, S R; Zhang, J; Chen, A; Eckhart, E A; Soffer, A; Toki, W H; Wilson, R J; Winklmeier, F; Zeng, Q; Altenburg, D D; Feltresi, E; Hauke, A; Jasper, H; Petzold, A; Spaan, B; Brandt, T; Klose, V; Lacker, H M; Mader, W F; Nogowski, R; Schubert, J; Schubert, K R; Schwierz, R; Sundermann, J E; Volk, A; Bernard, D; Bonneaud, G R; Grenier, P; Latour, E; Thiebaux, C; Verderi, M; Bard, D J; Clark, P J; Gradl, W; Muheim, F; Playfer, S; Robertson, A I; Xie, Y; Andreotti, M; Bettoni, D; Bozzi, C; Calabrese, R; Cibinetto, G; Luppi, E; Negrini, M; Petrella, A; Piemontese, L; Prencipe, E; Anulli, F; Baldini-Ferroli, R; Calcaterra, A; De Sangro, R; Finocchiaro, G; Pacetti, S; Patteri, P; Peruzzi, I M; Piccolo, M; Rama, M; Zallo, A; Buzzo, A; Capra, R; Contri, R; Lo Vetere, M; Macri, M M; Monge, M R; Passaggio, S; Patrignani, C; Robutti, E; Santroni, A; Tosi, S; Brandenburg, G; Chaisanguanthum, K S; Morii, M; Wu, J; Dubitzky, R S; Marks, J; Schenk, S; Uwer, U; Bhimji, W; Bowerman, D A; Dauncey, P D; Egede, U; Flack, R L; Nash, J A; Nikolich, M B; Panduro-Vazquez, W; Chai, X; Charles, M J; Mallik, U; Meyer, N T; Ziegler, V; Cochran, J; Crawley, H B; Dong, L; Eyges, V; Meyer, W T; Prell, S; Rosenberg, E I; Rubin, A E; Gritsan, A V; Fritsch, M; Schott, G; Arnaud, N; Davier, M; Grosdidier, G; Höcker, A; Le Diberder, F R; Lepeltier, V; Lutz, A M; Oyanguren, A; Pruvot, S; Rodier, S; Roudeau, P; Schune, M H; Stocchi, A; Wang, W F; Wormser, G; Cheng, C H; Lange, D J; Wright, D M; Chavez, C A; Forster, I J; Fry, J R; Gabathuler, E; Gamet, R; George, K A; Hutchcroft, D E; Payne, D J; Schofield, K C; Touramanis, C; Bevan, A J; Di Lodovico, F; Menges, W; Sacco, R; Cowan, G; Flächer, H U; Hopkins, D A; Jackson, P S; McMahon, T R; Ricciardi, S; Salvatore, F; Wren, A C; Davis, C L; Allison, J; Barlow, N R; Barlow, R J; Chia, Y M; Edgar, C L; Lafferty, G D; Naisbit, M T; Williams, J C; Yi, J I; Chen, C; Hulsbergen, W D; Jawahery, A; Lae, C K; Roberts, D A; Simi, G; Blaylock, G; Dallapiccola, C; Hertzbach, S S; Li, X; Moore, T B; Saremi, S; Stängle, H; Willocq, S Y; Cowan, R; Sciolla, G; Sekula, S J; Spitznagel, M; Taylor, F; Yamamoto, R K; Kim, H; Patel, P M; Robertson, S H; Lazzaro, A; Lombardo, V; Palombo, F; Bauer, J M; Cremaldi, L; Eschenburg, V; Godang, R; Kroeger, R; Sanders, D A; Summers, D J; Zhao, H W; Brunet, S; Côte, D; Taras, P; Viaud, F B; Nicholson, H; Cavallo, N; De Nardo, Gallieno; Fabozzi, F; Gatto, C; Lista, L; Monorchio, D; Paolucci, P; Piccolo, D; Sciacca, C; Baak, M; Raven, G; Snoek, H L; Jessop, C P; LoSecco, J M; Allmendinger, T; Benelli, G; Gan, K K; Honscheid, K; Hufnagel, D; Jackson, P D; Kagan, H; Kass, R; Rahimi, A M; Ter-Antonian, R; Wong, Q K; Blount, N L; Brau, J E; Frey, R; Igonkina, O; Lu, M; Potter, C T; Rahmat, R; Sinev, N B; Strom, D; Strube, J; Torrence, E; Galeazzi, F; Gaz, A; Margoni, M; Morandin, M; Pompili, A; Posocco, M; Rotondo, M; Simonetto, F; Stroili, R; Voci, C; Benayoun, M; Chauveau, J; David, P; Del Buono, L; La Vaissière, C de; Hamon, O; Hartfiel, B L; John, M J J; Malcles, J; Ocariz, J; Roos, L; Therin, G; Behera, P K; Gladney, L; Panetta, J; Biasini, M; Covarelli, R; Pioppi, M; Angelini, C; Batignani, G; Bettarini, S; Bucci, F; Calderini, G; Carpinelli, M; Cenci, R; Forti, F; Giorgi, M A; Lusiani, A; Marchiori, G; Mazur, M A; Morganti, M; Neri, N; Rizzo, G; Walsh, J; Haire, M; Judd, D; Wagoner, D E; Biesiada, J; Danielson, N; Elmer, P; Lau, Y P; Lü, C; Olsen, J; Smith, A J S; Telnov, A V; Bellini, F; Cavoto, G; D'Orazio, A; Del Re, D; Di Marco, E; Faccini, R; Ferrarotto, F; Ferroni, F; Gaspero, M; Li Gioi, L; Mazzoni, M A; Morganti, S; Piredda, G; Polci, F; Safai-Tehrani, F; Voena, C; Ebert, M; Schröder, H; Waldi, R; Adye, T; De Groot, N; Franek, B; Olaiya, E O; Wilson, F F; Emery, S; Gaidot, A; Ganzhur, S F; Hamel de Monchenault, G; Kozanecki, Witold; Legendre, M; Vasseur, G; Yéche, C; Zito, M; Chen, X R; Liu, H; Park, W; Purohit, M V; Wilson, J R; Allen, M T; Aston, D; Bartoldus, R; Bechtle, P; Berger, N; Boyarski, A M; Claus, R; Coleman, J P; Convery, M R; Cristinziani, M; Dingfelder, J C; Dorfan, J; Dubois-Felsmann, G P; Dujmic, D; Dunwoodie, W M; Field, R C; Glanzman, T; Gowdy, S J; Graham, M T; Halyo, V; Hast, C; Hrynóva, T; Innes, W R; Kelsey, M H; Kim, P; Leith, D W G S; Li, S; Luitz, S; Lüth, V; Lynch, H L; MacFarlane, D B; Marsiske, H; Messner, R; Müller, D R; O'Grady, C P; Ozcan, V E; Perazzo, A; Perl, M; Pulliam, T; Ratcliff, B N; Roodman, A; Salnikov, A A; Schindler, R H; Schwiening, J; Snyder, A; Stelzer, J; Su, D; Sullivan, M K; Suzuki, K; Swain, S K; Thompson, J M; Vavra, J; Van Bakel, N; Weaver, M; Weinstein, A J R; Wisniewski, W J; Wittgen, M; Wright, D H; Yarritu, A K; Yi, K; Young, C C; Burchat, P R; Edwards, A J; Majewski, S A; Petersen, B A; Roat, C; Wilden, L; Ahmed, S; Alam, M S; Bula, R; Ernst, J A; Jain, V; Pan, B; Saeed, M A; Wappler, F R; Zain, S B; Bugg, W; Krishnamurthy, M; Spanier, S M; Eckmann, R; Ritchie, J L; Satpathy, A; Schilling, C J; Schwitters, R F; Izen, J M; Kitayama, I; Lou, X C; Ye, S; Bianchi, F; Gallo, F; Gamba, D; Bomben, M; Bosisio, L; Cartaro, C; Cossutti, F; Della Ricca, G; Dittongo, S; Grancagnolo, S; Lanceri, L; Vitale, L; Martínez-Vidal, F; Azzolini, V; Banerjee, S; Bhuyan, B; Brown, C M; Fortin, D; Hamano, K; Kowalewski, R V; Nugent, I M; Roney, J M; Sobie, R J; Back, J J; Harrison, P F; Latham, T E; Mohanty, G B; Pappagallo, M; Band, H R; Chen, X; Cheng, B; Dasu, S; Datta, M; Flood, K T; Hollar, J J; Kutter, P E; Mellado, B; Mihályi, A; Pan, Y; Pierini, M; Prepost, R; Wu, S L; Yu, Z; Neal, H

    2006-01-01

    We present a search for the decay of a B0 or B0bar meson to a K*0bar K0 or K*0 K0bar final state, using a sample of approximately 232 million BBbar events collected with the BABAR detector at the PEP-II asymmetric energy e+e- collider at SLAC. The measured branching fraction is B(B0 --> K*0bar K0) + B(B0 --> K*0 K0bar) = (0.2+0.9-0.8+0.1-0.3)x 10-6. We obtain the following upper limit for the branching fraction at 90% confidence level: B(B0 --> K*0bar K0) + B(B0 --> K*0 K0bar) phi K0 from sin(2beta).

  8. Improve the performance of orthogonal ASK/DPSK optical label switching by DC-balanced line encoding

    DEFF Research Database (Denmark)

    Chi, Nan; Xu, Lin; Zhang, J.;

    2006-01-01

    and transparency. This paper presents theoretical and experimental studies of ASK/DPSK labeling. It proposes that dc-balanced 8B10B coding can greatly improve ER tolerance, which in turn leads to better system performance. By using the 8B10B coding method, the paper demonstrates transmission and optical label...

  9. The Morphology of Collisionless Galactic Rings Exterior to Evolving Bars

    CERN Document Server

    Bagley, Micaela; Quillen, Alice C

    2008-01-01

    The morphology of the outer rings of early-type spiral galaxies is compared to integrations of massless collisionless particles initially in nearly circular orbits. Particles are perturbed by a quadrupolar gravitational potential corresponding to a growing and secularly evolving bar. We find that outer rings with R1R2 morphology and pseudorings are exhibited by the simulations even though they lack gaseous dissipation. Simulations with stronger bars form pseudorings earlier and more quickly than those with weaker bars. We find that the R1 ring, perpendicular to the bar, is fragile and dissolves after a few bar rotation periods if the bar pattern speed increases by more than ~ 8%, bar strength increases (by >~ 140%) after bar growth, or the bar is too strong (Q_T>0.3). If the bar slows down after formation, pseudoring morphology persists and the R2 ring perpendicular to the bar is populated due to resonance capture. The R2 ring remains misaligned with the bar and increases in ellipticity as the bar slows down....

  10. Study of psi(2S) Decays to gamma p bar{p}, pi^0 p bar{p} and eta p bar{p} and Search for p bar{p} Threshold Enhancements

    CERN Document Server

    Alexander, J P; Das, S; Ehrlich, R; Fields, L; Gibbons, L; Gray, S W; Hartill, D L; Heltsley, B K; Kreinick, D L; Kuznetsov, V E; Patterson, J R; Peterson, D; Riley, D; Ryd, A; Sadoff, A J; Shi, X; Sun, W M; Yelton, J; Rubin, P; Lowrey, N; Mehrabyan, S; Selen, M; Wiss, J; Adams, S; Kornicer, M; Mitchell, R E; Shepherd, M R; Tarbert, C M; Besson, D; Pedlar, T K; Xavier, J; Cronin-Hennessy, D; Hietala, J; Zweber, P; Dobbs, S; Metreveli, Z; Seth, K K; Tomaradze, A; Xiao, T; Brisbane, S; Libby, J; Martin, L; Powell, A; Spradlin, P; Wilkinson, G; Mendez, H; Ge, J Y; Miller, D H; Shipsey, I P J; Xin, B; Adams, G S; Hu, D; Moziak, B; Napolitano, J; Ecklund, K M; Insler, J; Muramatsu, H; Park, C S; Pearson, L J; Thorndike, E H; Yang, F; Ricciardi, S; Thomas, C; Artuso, M; Blusk, S; Mountain, R; Skwarnicki, T; Stone, S; Wang, J C; Zhang, L M; Bonvicini, G; Cinabro, D; Lincoln, A; Smith, M J; Zhou, P; Zhu, J; Naik, P; Rademacker, J; Asner, D M; Edwards, K W; Randrianarivony, K; Tatishvili, G; Briere, R A; Vogel, H; Onyisi, P U E; Rosner, J L

    2010-01-01

    The decays of psi(2S) into gamma p bar{p}, pi^0 p bar{p} and eta p bar{p} have been studied with the CLEO-c detector using a sample of 24.5 million psi(2S) events obtained from e^+e^- annihilations at sqrt{s} = 3686 MeV. The data show evidence for the excitation of several N^* resonances in p pi^0 and p eta channels in pi^0 p bar{p} and eta p bar{p} decays, and f_2 states in gamma p bar{p} decay. Branching fractions for decays of psi(2S) to gamma p bar{p}, pi^0 p bar{p} and eta p bar{p} have been determined. No evidence for p bar{p} threshold enhancements was found in the reactions psi(2S)-> X p bar{p}, where X = gamma, pi^0, eta. We do, however, find confirming evidence for a p bar{p} threshold enhancement in J/psi-> gamma p bar{p} as previously reported by BES.

  11. Fundamentals of convolutional coding

    CERN Document Server

    Johannesson, Rolf

    2015-01-01

    Fundamentals of Convolutional Coding, Second Edition, regarded as a bible of convolutional coding brings you a clear and comprehensive discussion of the basic principles of this field * Two new chapters on low-density parity-check (LDPC) convolutional codes and iterative coding * Viterbi, BCJR, BEAST, list, and sequential decoding of convolutional codes * Distance properties of convolutional codes * Includes a downloadable solutions manual

  12. CP asymmetry Relations Between $\\bar B^0\\rightarrow \\pi\\pi$ and $\\bar B^0\\rightarrow \\pi K$ Rates

    OpenAIRE

    Deshpande, N. G.; He, Xiao-Gang(INPAC, SKLPPC and Department of Physics, Shanghai Jiao Tong University, Shanghai, China)

    1994-01-01

    We prove that CP violating rate difference $\\Delta (\\bar B^0 \\rightarrow \\pi^+\\pi^-) = \\Gamma (\\bar B^0 \\rightarrow \\pi^+\\pi^-) - \\Gamma ( B^0 \\rightarrow \\pi^-\\pi^+)$ is related to $\\Delta (\\bar B^0 \\rightarrow \\pi^+ K^-) = \\Gamma (\\bar B^0 \\rightarrow \\pi^+K^-) - \\Gamma (B^0 \\rightarrow \\pi^-K^+)$ in the three generation Standard Model. Neglecting small annihilation diagrams, and in the SU(3) symmetry limit, we show $\\Delta (\\bar B^0 \\rightarrow \\pi^+\\pi^-) = - \\Delta (\\bar B^0 \\rightarrow ...

  13. Nucleon strange $s\\bar s$ asymmetry to the $\\Lambda/\\bar\\Lambda$ fragmentation

    CERN Document Server

    Chi, Yujie; Ma, Bo-Qiang

    2014-01-01

    The difference between the $\\Lambda$ and $\\bar \\Lambda$ longitudinal spin transfers in the semi-inclusive deep inelastic scattering process is intensively studied. The study is performed in the current fragmentation region, by considering the intermediate hyperon decay processes and sea quark fragmentation processes, while the strange sea $s\\bar s$ asymmetry in the nucleon is taken into account. The calculation in the light-cone quark-diquark model shows that the strange sea asymmetry gives a proper trend to the difference between the $\\Lambda$ and $\\bar \\Lambda$ longitudinal spin transfers. When considering the nonzero final hadron transverse momentum, our results can explain the COMPASS data reasonably. The nonzero final hadron transverse momentum is interpreted as a natural constraint to the final hadron $z$ range where the longitudinal spin transfer is more sensitive to the strange sea $s\\bar s$ asymmetry.

  14. X(5568) as a {su}\\bar{d}\\bar{b} tetraquark in a simple quark model

    Science.gov (United States)

    Stancu, Fl

    2016-10-01

    The S-wave eigenstates of tetraquarks of type {su}\\bar{d}\\bar{b} with J P = 0+, 1+ and 2+ are studied within a simple quark model with chromomagnetic interaction and effective quark masses extracted from meson and baryon spectra. It is tempting to see if this spectrum can accommodate the new narrow structure X(5568), observed by the DØ Collaboration, but not confirmed by the LHCb Collaboration. If it exists, such a tetraquark is a system with four different flavors and its study can improve our understanding of multiquark systems. The presently calculated mass of X(5568) agrees quite well with the experimental value of the DØ Collaboration. Predictions are also made for the spectrum of the charmed partner {su}\\bar{d}\\bar{c}. However we are aware of the difficulty of extracting effective quark masses, from mesons and baryons, to be used in multiquark systems.

  15. Off-Label Drug Use

    Science.gov (United States)

    ... Your Local Offices Close + - Text Size Off-label Drug Use What is off-label drug use? In the United States new drugs are ... unapproved use of a drug. Is off-label drug use legal? The off-label use of FDA- ...

  16. Genetic algorithms for map labeling

    NARCIS (Netherlands)

    Dijk, Steven Ferdinand van

    2002-01-01

    Map labeling is the cartographic problem of placing the names of features (for example cities or rivers) on the map. A good labeling has no intersections between labels. Even basic versions of the problem are NP-hard. In addition, realistic map-labeling problems deal with many cartographic constr

  17. European consumers and nutrition labelling

    DEFF Research Database (Denmark)

    Wills, Josephine M.; Grunert, Klaus G.; Celemín, Laura Fernández;

    2009-01-01

    Nutrition labelling of food in Europe is not compulsory, unless a nutrition or health claim is made for the product. The European Commission is proposing mandatory nutrition labelling, even front of pack labelling with nutrition information. Yet, how widespread is nutrition labelling in the EU...

  18. Osmundiron, cleaved iron bars and slags (Osmundjern, kloder og kalotslagger)

    DEFF Research Database (Denmark)

    Buchwald, Vagn Fabritius

    1996-01-01

    Investigation of so-called Osmund iron, iron bars and slags from iron production in the medieval ages.......Investigation of so-called Osmund iron, iron bars and slags from iron production in the medieval ages....

  19. Rare kaon decays: $K^{+} → ^{+} \\bar{}$ and future

    Indian Academy of Sciences (India)

    Bipul Bhuyan

    2004-03-01

    The experimental progress in the search for $K^{+} → ^{+} \\bar{}$ will be presented in this paper. Also the physics potential of the proposed BNL experiment to search for $K_{L}^{0} → ^{0} \\bar{}$ (KOPIO) will be discussed.

  20. Strong resilience of topological codes to depolarization

    CERN Document Server

    Bombin, H; Ohzeki, Masayuki; Katzgraber, Helmut G; Martin-Delgado, M A

    2012-01-01

    The inevitable presence of decoherence effects in systems suitable for quantum computation necessitates effective error correction schemes to protect information from noise. We compute the stability of the toric code to depolarization by mapping the quantum problem onto a classical disordered eight-vertex Ising model. By studying the stability of the related ferromagnetic phase both via large-scale Monte Carlo simulations and via the duality method, we are able to demonstrate an increased error threshold of 18.9(3)% when noise correlations are taken into account. Remarkably, this agrees within error bars with the result for a different class of codes---topological color codes---where the mapping yields interesting new types of interacting 8-vertex models.

  1. Bar pattern speeds in CALIFA galaxies: I. Fast bars across the Hubble sequence

    CERN Document Server

    Aguerri, J A L; Falcón-Barroso, J; Amorin, A; Barrera-Ballesteros, J; Fernandes, R Cid; García-Benito, R; García-Lorenzo, B; Delgado, R M González; Husemann, B; Kalinova, V; Lyubenova, M; Marino, R A; Márquez, I; Mast, D; Pérez, E; Sánchez, S F; van de Ven, G; Walcher, C J; Backsmann, N; Cortijo-Ferrero, C; Bland-Hawthorn, J; del Olmo, A; Iglesias-Páramo, J; Pérez, I; Sánchez-Blázquez, P; Wisotzki, L; Ziegler, B

    2015-01-01

    The bar pattern speed ($\\Omega_{\\rm b}$) is defined as the rotational frequency of the bar, and it determines the bar dynamics. Several methods have been proposed for measuring $\\Omega_{\\rm b}$. The non-parametric method proposed by Tremaine \\& Weinberg (1984; TW) and based on stellar kinematics is the most accurate. This method has been applied so far to 17 galaxies, most of them SB0 and SBa types. We have applied the TW method to a new sample of 15 strong and bright barred galaxies, spanning a wide range of morphological types from SB0 to SBbc. Combining our analysis with previous studies, we investigate 32 barred galaxies with their pattern speed measured by the TW method. The resulting total sample of barred galaxies allows us to study the dependence of $\\Omega_{\\rm b}$ on galaxy properties, such as the Hubble type. We measured $\\Omega_{\\rm b}$ using the TW method on the stellar velocity maps provided by the integral-field spectroscopy data from the CALIFA survey. Integral-field data solve the problem...

  2. Strong Trinucleotide Circular Codes

    Directory of Open Access Journals (Sweden)

    Christian J. Michel

    2011-01-01

    Full Text Available Recently, we identified a hierarchy relation between trinucleotide comma-free codes and trinucleotide circular codes (see our previous works. Here, we extend our hierarchy with two new classes of codes, called DLD and LDL codes, which are stronger than the comma-free codes. We also prove that no circular code with 20 trinucleotides is a DLD code and that a circular code with 20 trinucleotides is comma-free if and only if it is a LDL code. Finally, we point out the possible role of the symmetric group ∑4 in the mathematical study of trinucleotide circular codes.

  3. Modeling of concrete cracking due to corrosion process of reinforcement bars

    International Nuclear Information System (INIS)

    The reinforcement corrosion in Reinforced Concrete (RC) is a major reason of degradation for structures and infrastructures throughout the world leading to their premature deterioration before design life was attained. The effects of corrosion of reinforcement are: (i) the reduction of the cross section of the bars, and (ii) the development of corrosion products leading to the appearance of cracks in the concrete cover and subsequent cover spalling. Due to their intrinsic complex nature, these issues require an interdisciplinary approach involving both material science and structural design knowledge also in terms on International and National codes that implemented the concept of durability and service life of structures. In this paper preliminary FEM analyses were performed in order to simulate pitting corrosion or general corrosion aimed to demonstrate the possibility to extend the results obtained for a cylindrical specimen, reinforced by a single bar, to more complex RC members in terms of geometry and reinforcement. Furthermore, a mechanical analytical model to evaluate the stresses in the concrete surrounding the reinforcement bars is proposed. In addition, a sophisticated model is presented to evaluate the non-linear development of stresses inside concrete and crack propagation when reinforcement bars start to corrode. The relationships between the cracking development (mechanical) and the reduction of the steel section (electrochemical) are provided. Finally, numerical findings reported in this paper were compared to experimental results available in the literature and satisfactory agreement was found

  4. Radioactive labelling of peptidic hormones

    International Nuclear Information System (INIS)

    The labelling of peptidic hormones requires stability, specificity and sensitivity of the label. Introduction of a radioactive atome is one way to satisfy these criteria. Several processes have been described to prepare radioactive TRF: synthesis of the peptide with labelled aminoacids or introduction of the label into the hormone. In that approach, tritium can be substituted in the imidazole ring, via precursors activating the proper carbon. Monoiodo TRF leads essentially to tritium labelling of the 5 positions whereas monoazo TRF allows the preparation of 3H TRF labelled in the 2 positions. Di-substituted TRF leads to labelling into the 2 and 5 carbons. Labelled analogs of TRF can be prepared with labelled iodine; further developments of peptide labelling, will be presented. In particular, the homolytic scission of the C-iodine, bond by photochemical activation. The nascent carbon radical can be stabilized by a tritiated scavenger. This approach eliminates the use of heavy metal catalysts

  5. Initial magnetic field distribution around high rectangular bus bars

    OpenAIRE

    Cividjian Grigore A.

    2014-01-01

    The one-dimensional transient electromagnetic field in and around a system of two nonmagnetic homogenous rectangular high thin bars can be analytically evaluated if the ratio of average initial magnetic field on the two sides of thin bar, or of the ratio of initial magnetic fields in middle of the bar height is known. In this paper, using appropriate conformal mappings, an exact analytical solution for these ratios are proposed in the case of very thin bars...

  6. Development of omega-3 rich energy bar with flaxseed

    OpenAIRE

    Mridula, D.; Singh, K. K.; Barnwal, P.

    2011-01-01

    Energy bar sample were prepared with different levels of flaxseed (0–20%) in addition to cereals and pulses with varying levels of sweeteners (45, 50, and 55%) to deliver a nutritious food to the consumer. The developed bars were evaluated for textural, colour, nutritional quality, sensory attributes and total microbial load. Different levels of flaxseed and sweeteners significantly affected the hue and chroma values of the energy bar. In general the level of flaxseed in energy bar did not af...

  7. Decoding Different Patterns in Various Grey Tones Incorporated in the QR Code

    Directory of Open Access Journals (Sweden)

    Filip Cvitić

    2014-07-01

    Full Text Available Using colors in bar codes causes errors that may adversely affect their readability (Tan etal. 2010, given that the contrast between data and background modules is reduced. Due to the unreliability of using color bar codes, most designers still keep to the limitations placed by Pira International (Smithers Pira in 2002 (Williams, 2004. Since the contrast between data modules and background modules is the most important aspect in the process of reliable bar code decoding, this paper explores the dependence of reliable decoding of QR codes incorporated with combinations of grey tones on the technical characteristics of the cameras on smartphones that were marketed in the period between 2008 and 2012.

  8. RFID Electronic Label of Internet of Things Based on Logistics Management System%基于RFID电子标签的物联网物流管理系统

    Institute of Scientific and Technical Information of China (English)

    邓超

    2014-01-01

    该文首先对基于RFID电子标签进行分析,重点介绍了RFID技术和基于RFID电子标签;再根据不同的分类标准,介绍不同类型的RFID电子标签;指出RFID电子标签和传统条形码的区别,总结RFID电子标签的优点。然后,该文在重点介绍基于RFID电子标签物联网物流管理的工作流程,分析物联网物流管理系统功能及应用。%This paper first carries on the analysis to the RFID tag based, focusing on the introduction of RFID technology and RFID based electronic label; then according to different classification criteria, RFID electronic label of different types; pointed out the difference between RFID and the traditional bar code tag, summarize the advantages of RFID electronic label. Then, the RFID electronic tag IOT logistics management work flow based on the analysis of Internet of things in the emphasis on logistics management system function and application.

  9. 10 CFR 39.49 - Uranium sinker bars.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Uranium sinker bars. 39.49 Section 39.49 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.49 Uranium sinker bars. The licensee may use a uranium sinker bar in well logging applications only if it is...

  10. Prediction of Vibration Transmission within Periodic Bar Structures

    DEFF Research Database (Denmark)

    Domadiya, Parthkumar Gandalal; Andersen, Lars Vabbersgaard; Sorokin, Sergey

    2012-01-01

    The present analysis focuses on vibration transmission within semi-infinite bar structure. The bar is consisting of two different materials in a periodic manner. A periodic bar model is generated using two various methods: The Finite Element method (FEM) and a Floquet theory approach. A parameter...

  11. 21 CFR 886.5800 - Ophthalmic bar reader.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic bar reader. 886.5800 Section 886.5800...) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5800 Ophthalmic bar reader. (a) Identification. An ophthalmic bar reader is a device that consists of a magnifying lens intended for use by...

  12. $\\chi^{\\vphantom\\dagger}_{c0}(3915)$ As the Lightest $c\\bar c s \\bar s$ State

    CERN Document Server

    Lebed, Richard F

    2016-01-01

    The state $\\chi^{\\vphantom\\dagger}_{c0}(3915)$ has recently been demoted by the Particle Data Group from its previous status as the conventional $c\\bar c$ $2 {}^3P_0$ state, largely due to the absence of expected $D\\bar D$ decays. We propose that $\\chi^{\\vphantom\\dagger}_{c0}(3915)$ is actually the lightest $c\\bar c s \\bar s$ state, and calculate the spectrum of such states using the diquark model, identifying many of the observed charmoniumlike states that lack open-charm decay modes as $c\\bar c s \\bar s$. Among other results, we argue that $Y(4140)$ is a $J^{PC} = 1^{++}$ $c\\bar c s \\bar s$ state that has been not been seen in two-photon fusion largely as a consequence of the Landau-Yang theorem.

  13. Seismic Behavor of RC Beam-Column Joint with Additional Bars under Cyclic Loading

    Institute of Scientific and Technical Information of China (English)

    LU Xilin; Tonny H.URUKAP; LI Sen

    2011-01-01

    The behavior of Beam-Column Joints in moment resisting frame structures are susceptible to damage caused by seismic effects due to poor performance of the joint. A good number of researches were carried out to understand the complex mechanism of RC joints which are considered in seismic design code practices presently adopted. The traditional construction detailing of transverse reinforcement have shown serious joint failure.This paper introduces a new design philosophy involving the use of additional diagonal bars within the joint particularly suitable for low to medium seismic effects in earthquake zones throughout the world. In lieu to this study, ten (10) full-scale interior beam-column specimens were constructed with various additional reinforcement details and configurations as will be discussed in the later. The experiment provided adequate results to proof the idea of additional bars as suitable approach in reinforced concrete structures where earthquake is eminent. While compared with overall cracking observation during the test, the specimen with additional bars (diagonal and straight) had shown few cracks on the column than the ones without. Furthermore, concrete confinement is certainly an important design method as recommended by certain international codes.

  14. Joint source channel coding using arithmetic codes

    CERN Document Server

    Bi, Dongsheng

    2009-01-01

    Based on the encoding process, arithmetic codes can be viewed as tree codes and current proposals for decoding arithmetic codes with forbidden symbols belong to sequential decoding algorithms and their variants. In this monograph, we propose a new way of looking at arithmetic codes with forbidden symbols. If a limit is imposed on the maximum value of a key parameter in the encoder, this modified arithmetic encoder can also be modeled as a finite state machine and the code generated can be treated as a variable-length trellis code. The number of states used can be reduced and techniques used fo

  15. Synthesis of labeled compounds

    International Nuclear Information System (INIS)

    Intermediate compounds labeled with 13C included methane, sodium cyanide, methanol, ethanol, and acetonitrile. A new method for synthesizing 15N-labeled 4-ethylsulfonyl-1-naphthalene-sulfonamide was developed. Studies were conducted on pathways to oleic-1-13C acid and a second pathway investigated was based on carbonation of 8-heptadecynylmagnesium bromide with CO2 to prepare sterolic acid. Biosynthetic preparations included glucose-13C from starch isolated from tobacco leaves following photosynthetic incubation with 13CO2 and galactose-13C from galactosylglycerol-13C from kelp. Research on growth of organisms emphasized photosynthetic growth of algae in which all cellular carbon is labeled. Preliminary experiments were performed to optimize the growth of Escherichia coli on sodium acetate-13C

  16. A novel all-optical label processing for OPS networks based on multiple OOC sequences from multiple-groups OOC

    Science.gov (United States)

    Qiu, Kun; Zhang, Chongfu; Ling, Yun; Wang, Yibo

    2007-11-01

    This paper proposes an all-optical label processing scheme using multiple optical orthogonal codes sequences (MOOCS) for optical packet switching (OPS) (MOOCS-OPS) networks, for the first time to the best of our knowledge. In this scheme, the multiple optical orthogonal codes (MOOC) from multiple-groups optical orthogonal codes (MGOOC) are permuted and combined to obtain the MOOCS for the optical labels, which are used to effectively enlarge the capacity of available optical codes for optical labels. The optical label processing (OLP) schemes are reviewed and analyzed, the principles of MOOCS-based optical labels for OPS networks are given, and analyzed, then the MOOCS-OPS topology and the key realization units of the MOOCS-based optical label packets are studied in detail, respectively. The performances of this novel all-optical label processing technology are analyzed, the corresponding simulation is performed. These analysis and results show that the proposed scheme can overcome the lack of available optical orthogonal codes (OOC)-based optical labels due to the limited number of single OOC for optical label with the short code length, and indicate that the MOOCS-OPS scheme is feasible.

  17. Semantic Role Labeling

    CERN Document Server

    Palmer, Martha; Xue, Nianwen

    2011-01-01

    This book is aimed at providing an overview of several aspects of semantic role labeling. Chapter 1 begins with linguistic background on the definition of semantic roles and the controversies surrounding them. Chapter 2 describes how the theories have led to structured lexicons such as FrameNet, VerbNet and the PropBank Frame Files that in turn provide the basis for large scale semantic annotation of corpora. This data has facilitated the development of automatic semantic role labeling systems based on supervised machine learning techniques. Chapter 3 presents the general principles of applyin

  18. A train for the bus(bars)

    CERN Multimedia

    CERN Bulletin

    2013-01-01

    On 8 April, the first SMACC (Superconducting Magnets and Circuits Consolidation) teams began work in the LHC tunnel. They are responsible for opening the interconnects between the magnets, laying the groundwork for the series of operations that will be performed by the team riding the ‘consolidation train’.   A technician installs the machine tool that allows them to prepare the surface of the section of the bar where the shunt will be fixed. The LHC’s 1,670 dipoles and quadrupoles are powered by power converters and connected by copper 'busbars’. The superconducting cables run through these bars, carrying a current of up to 11,850 amps. Six superconducting cables meet at each interconnect, where they are held together by a soldered (see box) electrical connection sandwiched between two pieces of copper, forming the splice between the busbars of the neighbouring magnets. The integrity of the electrical circuit is depen...

  19. Arbejdsulykker inden for BAR-SOSU

    DEFF Research Database (Denmark)

    Jørgensen, Kirsten

    Denne rapport er udarbejdet til BAR SOSU, som har formuleret følgende opgave: 1. At få udarbejdet et overblik over den viden om ulykker indenfor SOSU´s område, som foreligger i eksisterende statistikker, med henblik på udviklingen over de seneste 5-10 år, ulykkernes konsekvenser i form af skadens...... art og i det omfang det er muligt også ulykkernes art. 2. At få gennemgået BAR SOSU´s nuværende materiale målrettet ulykkesforebyggelse og vurdere, hvad der kan udvikles yderligere til brug for at styrke det ulykkesforebyggende arbejde. 3. Med udgangspunkt i nyere forskning om ulykkesforebyggelse og...

  20. The Disability Dilemma: A Skeptical Bench & Bar

    Directory of Open Access Journals (Sweden)

    Wendy F. Hensel

    2008-04-01

    Full Text Available The legal profession is no stranger to the bias and prejudice present in American society. Members of the bar have been shown to engage in both conscious and subconscious sexism and racism, posing challenges to the profession as the profile of those practicing law has changed over the last several decades to admit increasing numbers of women and minorities.1 Nevertheless, it is notable that few, if any, members of the bar today would question openly whether women or people of color have the ability to be successful, productive members of the profession. Instead, the conventional wisdom is that the greatest obstacles to their success will come in the form of external barriers and institutional policies based on preconceived norms that do not acknowledge the divergent challenges faced by these group members.

  1. A Distinct Structure Inside the Galactic Bar

    CERN Document Server

    Nishiyama, S; Baba, D; Haba, Y; Kadowaki, R; Kato, D; Kurita, M; Nagashima, C; Nagayama, T; Murai, Y; Nakajima, Y; Tamura, M; Nakaya, H; Sugitani, K; Naoi, T; Matsunaga, N; Tanabé, T; Kusakabe, N; Sato, S; Nishiyama, Shogo; Nagata, Tetsuya; Baba, Daisuke; Haba, Yasuaki; Kadowaki, Ryota; Kato, Daisuke; Kurita, Mikio; Nagashima, Chie; Nagayama, Takahiro; Murai, Yuka; Nakajima, Yasushi; Tamura, Motohide; Nakaya, Hidehiko; Sugitani, Koji; Naoi, Takahiro; Matsunaga, Noriyuki; Tanabe, Toshihiko; Kusakabe, Nobuhiko; Sato, Shuji

    2005-01-01

    We present the result of a near-infrared (J H Ks) survey along the Galactic plane, -10.5deg < l < +10.5deg and b=+1.0deg, with the IRSF 1.4m telescope and the SIRIUS camera. Ks vs. H-Ks color-magnitude diagrams reveal a well-defined population of red clump (RC) stars whose apparent magnitude peak changes continuously along the Galactic plane, from Ks=13.4 at l=-10deg to Ks=12.2 at l=+10deg after dereddening. This variation can be explained by the bar-like structure found in previous studies, but we find an additional inner structure at |l| < 4deg, where the longitude - apparent magnitude relation is distinct from the outer bar, and the apparent magnitude peak changes by only 0.1 mag over the central 8deg. The exact nature of this inner structure is as yet uncertain.

  2. Rock Bar BTR -liiketoimintasuunnitelma baariyrityksen perustamiseksi

    OpenAIRE

    Rieppo, Jani

    2015-01-01

    Laurea-ammattikorkeakoulu Tiivistelmä Laurea Leppävaara Hotelli- ja ravintola-alan liikkeenjohdon koulutusohjelma Rieppo, Jani Rock Bar BTR -liiketoimintasuunnitelma baariyrityksen perustamiseksi Vuosi 2015 Sivumäärä 58 Tämän toiminnallisen opinnäytetyön tarkoituksena on liiketoimintasuunnitelman laatiminen uudelle rock-baarille, jonka avaaminen Joensuuhun on suunnitelman laatijan toimesta mahdollista joskus tulevaisuudessa. Tavo...

  3. Hadron Physics in BaBar

    Energy Technology Data Exchange (ETDEWEB)

    Lafferty, G.D.; /Manchester U.

    2005-08-29

    Some recent results in hadron physics from the BaBar experiment are discussed. In particular, the observation of two new charmed states, the D*{sub sJ}{sup +}(2317) and the D*{sub sJ}{sup +}(2457), is described, and results are presented on the first measurement of the rare decay mode of the B meson, B{sup 0} {pi}{sup 0}{pi}{sup 0}.

  4. The Expansion of Speakeasy Bar and Grill

    OpenAIRE

    Mills, Joel

    2012-01-01

    This strategic analysis makes recommendations on a course of action for Speakeasy Bar and Grill, located in Vancouver, British Columbia, with regards to growth of the brand. The comprehensive analysis determined that Speakeasy currently generates a competitive source of advantage in large part from the high level of direct involvement of its owners as managers, both in terms of cost and customer value advantages. Sustaining this advantage as the company grows with greater demands being placed...

  5. Dowel Bar Retrofit Mix Design and Specification

    OpenAIRE

    Deshpande, Yogini; Olek, Jan

    2012-01-01

    When dealing with the issue of repair of concrete pavement repair using dowel bar retrofit technique, it is very desirable for the repair material to have high fluidity that can ensure good compaction and facilitate flow to tight spaces, preferably without the use of a vibrator. The focus of this project was on identifying critical properties that control long-term performance of repair concrete, especially rapid-setting materials extended using pea gravel (maximum size aggregate 9.5 mm). ...

  6. INFINITELY VARIABLE TRANSMISSION USING FOUR BAR MECHANISM

    Directory of Open Access Journals (Sweden)

    Dr.N. ARUNKUMAR

    2014-04-01

    Full Text Available Most of the continuously variable transmission systems in automobiles now-a-days are non-positive drives. This means that they cannot be used in heavy vehicles that require very high torque to be transmitted. This new type of infinitely variable transmission is aimed at transmitting high torques by making it a positive drive, thus making continuously variable transmission systems to be suitable for heavy vehicles. Infinitely variable transmission system and continuously variable transmission system are both the same except that there is an extra zero gear ratio in infinitely variable transmission system. This newly developed transmission system is basically a four bar mechanism with variable crank radius which makes it possible to have continuously variable mechanical advantage. The output lever which oscillates in the four bar mechanism is connected to a ratchet mechanism which turns the output shaft intermittently, two four bar mechanisms with a phase difference of 180 degrees is used to avoid the intermittent rotation of the output shaft. A flywheel is used in the output shaft to reduce the fluctuations in both speed and torque.

  7. Formation of Nuclear Spirals in Barred Galaxies

    CERN Document Server

    Ann, H B; Thakur, Parijat

    2004-01-01

    We have performed smoothed particle hydrodynamics (SPH) simulations for the response of the gaseous disk to the imposed moderately strong non-axisymmetric potentials. The model galaxies are composed of the three stellar components (disk, bulge and bar) and two dark ones (supermassive black hole and halo) whose gravitational potentials are assumed to be invariant in time in the frame corotating with the bar. We found that the torques alone generated by the moderately strong bar that gives the maximum of tangential-to-radial force ratio as $(F_{Tan}/F_{Rad})_{max}= 0.3$ are not sufficient to drive the gas particles close to the center due to the barrier imposed by the inner Lindblad resonances (ILRs). In order to transport the gas particles towards the nucleus ($r<100$ pc), a central supermassive black hole (SMBH) and high sound speed of the gas are required to be present. The former is required to remove the inner inner Lindblad resonance (IILR) that prevents gas inflow close to the nucleus, while the latte...

  8. Leptonic B Decays at BaBar

    Energy Technology Data Exchange (ETDEWEB)

    Monorchio, Diego; /INFN, Naples /Naples U.

    2011-09-13

    The authors will present the most recent results on leptonic B decays B{sup {+-}(0)} {yields} K*{sup {+-}(0)} {nu}{bar {nu}} and B{sup {+-}} {yields} {mu}{sup {+-}}{nu}, based on the data collected by the BaBar detector at PEP-II, an asymmetric e{sup +}e{sup -} collider at the center of mass energy of the {Upsilon}(4S) resonance. Rare B decays have always been a standard probe for New Physics (NP) searches. The very low Standard Model (SM) rate of these decays often make them unaccessible with the present experimental datasets, unless NP effects enhance the rate up to the current experimental sensitivity. Moreover, as NP effects can modify the decay kinematic, particular attention must be payed in order to perform a model independent analysis. A B-Factory provides an unique environment where to investigate these processes. The high number of B{bar B} pairs produced by a B-Factory often allows to approach the needed experimental sensitivity. Moreover, the clean environment and the closed kinematic of the initial state enable to obtaining a very pure sample where to look for these decays.

  9. Leptonic B Decays at BaBar

    Energy Technology Data Exchange (ETDEWEB)

    Baracchini, Elisabetta; /Rome U. /INFN, Rome

    2011-11-10

    We will present the most recent results on leptonic B decays B{sup {+-}(0)} {yields} K*{sup {+-}(0)}{nu}{bar {nu}} and B{sup {+-}} {yields} {mu}{sup {+-}}{nu}, based on the data collected by the BaBar detector at PEP-II, an asymmetric e{sup +}e{sup -} collider at the center of mass energy of the {Upsilon}(4S) resonance. Rare B decays have always been a standard probe for New Physics (NP) searches. The very low Standard Model (SM) rate of these decays often make them unaccessible with the present experimental datasets, unless NP effects enhance the rate up to the current experimental sensitivity. Moreover, as NP effects can modify the decay kinematic, particular attention must be paid in order to perform a model independent analysis. A B-Factory provides an unique environment to investigate these processes. The high number of B{bar B} pairs produced by a B-Factory often allows to approach the needed experimental sensitivity. Moreover, the clean environment and the closed kinematic of the initial state enable to obtaining a very pure sample where to look for these decays.

  10. Model Children's Code.

    Science.gov (United States)

    New Mexico Univ., Albuquerque. American Indian Law Center.

    The Model Children's Code was developed to provide a legally correct model code that American Indian tribes can use to enact children's codes that fulfill their legal, cultural and economic needs. Code sections cover the court system, jurisdiction, juvenile offender procedures, minor-in-need-of-care, and termination. Almost every Code section is…

  11. Initial magnetic field distribution around high rectangular bus bars

    Directory of Open Access Journals (Sweden)

    Cividjian Grigore A.

    2014-01-01

    Full Text Available The one-dimensional transient electromagnetic field in and around a system of two nonmagnetic homogenous rectangular high thin bars can be analytically evaluated if the ratio of average initial magnetic field on the two sides of thin bar, or of the ratio of initial magnetic fields in middle of the bar height is known. In this paper, using appropriate conformal mappings, an exact analytical solution for these ratios are proposed in the case of very thin bars. Obtained values are compared with FEM results for relatively thick bars.

  12. Antihydrogen Production in $ \\bar{p} $ Z - interaction

    CERN Multimedia

    2002-01-01

    % PS210 \\\\ \\\\ The production of the antihydrogen atom $ \\bar {H}^0 \\equiv \\bar{p}e $ as the simplest atomic bound state of antimatter has been studied. Nine $ \\bar {H}^0 $ have been observed.\\\\ \\\\ The production of $ \\bar {H}^0 $ is predominantly mediated by the two-photon mechanism in the antiproton-nucleus interaction. In principle $ \\bar {H}^0 $ is well suited for investigations of fundamental CPT violation studies under different forces, however, in the present experiment we concentrated on the production of this antimatter object, since so far it never had been observed.

  13. Heat Transfer in the LHC Main Superconducting Bus Bars

    CERN Document Server

    Granieri, P P; Richter, D

    2011-01-01

    CERN is performing a systematic analysis of the interconnecting bus bars of the Large Hadron Collider (LHC) main magnets. Their thermal, electrical, mechanical and hydraulic performances are addressed. In the frame of these studies, the heat transfer between the main superconducting (SC) bus bars and the surrounding He bath is investigated. It represents a key parameter in the comprehension of the bus bars stability and quench propagation mechanisms, thus crucial for the analysis of the 2008 incident which was triggered by a defective bus bars joint. This paper reports on the experimental tests and relative analysis aiming at describing the thermal behavior of the LHC main bus bars.

  14. FAST LABEL: Easy and efficient solution of joint multi-label and estimation problems

    KAUST Repository

    Sundaramoorthi, Ganesh

    2014-06-01

    We derive an easy-to-implement and efficient algorithm for solving multi-label image partitioning problems in the form of the problem addressed by Region Competition. These problems jointly determine a parameter for each of the regions in the partition. Given an estimate of the parameters, a fast approximate solution to the multi-label sub-problem is derived by a global update that uses smoothing and thresholding. The method is empirically validated to be robust to fine details of the image that plague local solutions. Further, in comparison to global methods for the multi-label problem, the method is more efficient and it is easy for a non-specialist to implement. We give sample Matlab code for the multi-label Chan-Vese problem in this paper! Experimental comparison to the state-of-the-art in multi-label solutions to Region Competition shows that our method achieves equal or better accuracy, with the main advantage being speed and ease of implementation.

  15. Multi-label

    Directory of Open Access Journals (Sweden)

    Neda Abdelhamid

    2015-01-01

    Full Text Available Generating multi-label rules in associative classification (AC from single label data sets is considered a challenging task making the number of existing algorithms for this task rare. Current AC algorithms produce only the largest frequency class connected with a rule in the training data set and discard all other classes even though these classes have data representation with the rule’s body. In this paper, we deal with the above problem by proposing an AC algorithm called Enhanced Multi-label Classifiers based Associative Classification (eMCAC. This algorithm discovers rules associated with a set of classes from single label data that other current AC algorithms are unable to induce. Furthermore, eMCAC minimises the number of extracted rules using a classifier building method. The proposed algorithm has been tested on a real world application data set related to website phishing and the results reveal that eMCAC’s accuracy is highly competitive if contrasted with other known AC and classic classification algorithms in data mining. Lastly, the experimental results show that our algorithm is able to derive new rules from the phishing data sets that end-users can exploit in decision making.

  16. Labeling of herbicide femesafen

    International Nuclear Information System (INIS)

    5-[2-chroo-4-(trifluoromethyl ) phenoxy]-N-(methyl sulphonyl )-2-niorobenzamide [femesafen] was labeled by six steps. Radio-chemical yield was 19.15%. TLC analysis of the final product showed that the radiochemical purity is not less than 99%. (authors)

  17. Waisda?: video labeling game

    NARCIS (Netherlands)

    Hildebrand, M.; Brinkerink, M.; Gligorov, R.; Steenbergen, M. van; Huijkman, J.; Oomen, J.

    2013-01-01

    The Waisda? video labeling game is a crowsourcing tool to collect user-generated metadata for video clips. It follows the paradigm of games-with-a-purpose, where two or more users play against each other by entering tags that describe the content of the video. Players score points by entering the sa

  18. Which bulges are favoured by barred S0 galaxies?

    CERN Document Server

    Barway, Sudhanshu; Vaghmare, Kaustubh; Kembhavi, Ajit K

    2016-01-01

    S0 galaxies are known to host classical bulges with a broad range of size and mass, while some such S0s are barred and some not. The origin of the bars has remained as a long-standing problem -- what made bar formation possible in certain S0s? By analysing a large sample of S0s with classical bulges observed by the Spitzer space telescope, we find that most of our barred S0s host comparatively low-mass classical bulges, typically with bulge-to-total ratio ($B/T$) less than $0.5$; whereas S0s with more massive classical bulges than these do not host any bar. Furthermore, we find that amongst the barred S0s, there is a trend for the longer and massive bars to be associated with comparatively bigger and massive classical bulges -- possibly suggesting bar growth being facilitated by these classical bulges. In addition, we find that the bulge effective radius is always less than the bar effective radius --indicating an interesting synergy between the host classical bulge and bars being maintained while bar growth ...

  19. On the galactic spin of barred disk galaxies

    CERN Document Server

    Cervantes-Sodi, Bernardo; Park, Changbom; Wang, Lixin

    2013-01-01

    We present a study of the connection between the galactic spin parameter $\\lambda_{d}$ and the bar fraction in a volume-limited sample of 10,674 disk galaxies drawn from the Sloan Digital Sky Survey Data Release 7. The galaxies in our sample are visually classified into galaxies hosting strong or weak bars, and non-barred galaxies. We find that the spin distributions of these three classes are statistically different, with galaxies hosting strong bars with the lowest $\\lambda_{d}$ values, followed by non-barred galaxies, while galaxies with weak bars present typically high spin parameters. The bar fraction presents its maximum at low to intermediate $\\lambda_{d}$ values for the case of strong bars, while the maximum for weak bars is at high $\\lambda_{d}$. This bi-modality is in good agreement with previous studies finding stronger bars hosted by luminous, massive, red galaxies with low content of cold gas, while weak bars are found in low luminosity, low mass, blue galaxies, usually gas rich. In addition, the...

  20. Automated bar detection in local disc galaxies from the SDSS - The colors of bars

    CERN Document Server

    Consolandi, Guido

    2016-01-01

    This paper describes an automatic isophotal fitting procedure that succeeds, without the support of any visual inspection of neither the images nor the ellipticity/P.A. radial profiles, at extracting a fairly pure sample of barred LTGs among thousands of optical images from the SDSS. The procedure relies on the methods described in Consolandi et al. (2016) to robustly extract the photometrical properties of a large sample of local SDSS galaxies and is tailored to extract bars on the basis of their well-known peculiarities in their P.A. and ellipticity profiles. It has been run on a sample of 5853 galaxies in the Coma and Local supercluster. The procedure extracted for each galaxy a color, an ellipticity and a position angle radial profile of the ellipses fitted to the isophotes. Examining automatically the profiles of 922 face-on late-type galaxies (B/A >0.7) the procedure found that ~ 36 % are barred. The local bar fraction strongly increases with stellar mass. The sample of barred galaxies is used to constr...

  1. Slowly rotating bars-Morphologies introduced by bistability in barred-spiral galactic potentials

    CERN Document Server

    Tsigaridi, L

    2015-01-01

    We investigate the orbital dynamics of a \\textit{barred-spiral} model when the system is rotating slowly and corotation is located beyond the end of the spiral arms. In the characteristic of the central family of periodic orbits we find a "bistable region". In the response model we observe a ring surrounding the bar and spiral arms starting tangential to the ring. This is a morphology resembling barred-spiral systems with inner rings. However, the dynamics associated with this structure in the case we study is different from that of a typical bar ending close to corotation. The ring of our model is round, or rather elongated perpendicular to the bar. It is associated with a folding (an "S" shaped feature) of the characteristic of the central family, which is typical in bistable bifurcations. Along the "S" part of the characteristic we have a change in the orientation of the periodic orbits from a x1-type to a x2-type morphology. The orbits populated in the response model change rather abruptly their orientati...

  2. The relation between bar formation, galaxy luminosity, and environment

    CERN Document Server

    Corsini, E M; Sanchez-Janssen, R; Aguerri, J A L; Zarattini, S

    2013-01-01

    We derive the bar fraction in three different environments ranging from the field to Virgo and Coma clusters, covering an unprecedentedly large range of galaxy luminosities (or, equivalently, stellar masses). We confirm that the fraction of barred galaxies strongly depends on galaxy luminosity. We also show that the difference between the bar fraction distributions as a function of galaxy luminosity (and mass) in the field and Coma cluster are statistically significant, with Virgo being an intermediate case. We interpret this result as a variation of the effect of environment on bar formation depending on galaxy luminosity. We speculate that brighter disk galaxies are stable enough against interactions to keep their cold structure, thus, the interactions are able to trigger bar formation. For fainter galaxies the interactions become strong enough to heat up the disks inhibiting bar formation and even destroying the disks. Finally, we point out that the controversy regarding whether the bar fraction depends on...

  3. Genetic algorithms for map labeling

    OpenAIRE

    Dijk, Steven Ferdinand van

    2002-01-01

    Map labeling is the cartographic problem of placing the names of features (for example cities or rivers) on the map. A good labeling has no intersections between labels. Even basic versions of the problem are NP-hard. In addition, realistic map-labeling problems deal with many cartographic constraints, which pose more demands on how the labels should be placed in relation to their surroundings. For example, a label is preferably placed above and to the right of a city. These two aspects (comb...

  4. Nonbinary quantum codes

    OpenAIRE

    Eric M. Rains

    1997-01-01

    We present several results on quantum codes over general alphabets (that is, in which the fundamental units may have more than 2 states). In particular, we consider codes derived from finite symplectic geometry assumed to have additional global symmetries. From this standpoint, the analogues of Calderbank-Shor-Steane codes and of GF(4)-linear codes turn out to be special cases of the same construction. This allows us to construct families of quantum codes from certain codes over number fields...

  5. Rateless feedback codes

    DEFF Research Database (Denmark)

    Sørensen, Jesper Hemming; Koike-Akino, Toshiaki; Orlik, Philip

    2012-01-01

    This paper proposes a concept called rateless feedback coding. We redesign the existing LT and Raptor codes, by introducing new degree distributions for the case when a few feedback opportunities are available. We show that incorporating feedback to LT codes can significantly decrease both...... the coding overhead and the encoding/decoding complexity. Moreover, we show that, at the price of a slight increase in the coding overhead, linear complexity is achieved with Raptor feedback coding....

  6. Affine Grassmann codes

    DEFF Research Database (Denmark)

    Høholdt, Tom; Beelen, Peter; Ghorpade, Sudhir Ramakant

    2010-01-01

    We consider a new class of linear codes, called affine Grassmann codes. These can be viewed as a variant of generalized Reed-Muller codes and are closely related to Grassmann codes.We determine the length, dimension, and the minimum distance of any affine Grassmann code. Moreover, we show that...... affine Grassmann codes have a large automorphism group and determine the number of minimum weight codewords....

  7. Coding for dummies

    CERN Document Server

    Abraham, Nikhil

    2015-01-01

    Hands-on exercises help you learn to code like a pro No coding experience is required for Coding For Dummies,your one-stop guide to building a foundation of knowledge inwriting computer code for web, application, and softwaredevelopment. It doesn't matter if you've dabbled in coding or neverwritten a line of code, this book guides you through the basics.Using foundational web development languages like HTML, CSS, andJavaScript, it explains in plain English how coding works and whyit's needed. Online exercises developed by Codecademy, a leading online codetraining site, help hone coding skill

  8. Advanced video coding systems

    CERN Document Server

    Gao, Wen

    2015-01-01

    This comprehensive and accessible text/reference presents an overview of the state of the art in video coding technology. Specifically, the book introduces the tools of the AVS2 standard, describing how AVS2 can help to achieve a significant improvement in coding efficiency for future video networks and applications by incorporating smarter coding tools such as scene video coding. Topics and features: introduces the basic concepts in video coding, and presents a short history of video coding technology and standards; reviews the coding framework, main coding tools, and syntax structure of AV

  9. Polyphase alternating codes

    Directory of Open Access Journals (Sweden)

    M. Markkanen

    2008-08-01

    Full Text Available We present a new class of alternating codes. Instead of the customary binary phase codes, the new codes utilize either p or p–1 phases, where p is a prime number. The first class of codes has code length pm, where m is a positive integer, the second class has code length p–1. We give an actual construction algorithm, and explain the principles behind it. We handle a few specific examples in detail. The new codes offer an enlarged collection of code lengths for radar experiments.

  10. Use the Nutrition Facts Label

    Science.gov (United States)

    ... Features Spokespeople News Archive eNewsletters Calendar Use the Nutrition Facts Label You can help your family eat ... to some of their favorite foods. Use the Nutrition Facts label found on food packages to make ...

  11. Coupling CFD code with system code and neutron kinetic code

    International Nuclear Information System (INIS)

    Highlights: • Coupling interface between CFD code Fluent and system code Athlet was created. • Athlet code is internally coupled with neutron kinetic code Dyn3D. • Explicit coupling of overlapped computational domains was used. • A coupled system of Athlet/Dyn3D+Fluent codes was successfully tested on a real case. - Abstract: The aim of this work was to develop the coupling interface between CFD code Fluent and system code Athlet internally coupled with neutron kinetic code Dyn3D. The coupling interface is intended for simulation of complex transients such as Main Steam Line Break scenarios, which cannot be modeled separately first by system and neutron kinetic code and then by CFD code, because of the feedback between the codes. In the first part of this article, the coupling method is described. Explicit coupling of overlapped computational domains is used in this work. The second part of the article presents a demonstration simulation performed by the coupled system of Athlet/Dyn3D and Fluent. The “Opening a Steam Dump to the Atmosphere” test carried out at the Temelin NPP (VVER-1000) was simulated by the coupled system. In this simulation, the primary and secondary circuits were modeled by Athlet, mixing in downcomer and lower plenum was simulated by Fluent and heat generation in the core was calculated by Dyn3D. The results of the simulation with Athlet/Dyn3D+Fluent were compared with the experimental data and the results from a calculation performed with Athlet/Dyn3D without Fluent

  12. Dependence of Barred Galaxy Fraction on Galaxy Properties and Environment

    CERN Document Server

    Lee, Gwang-Ho; Lee, Myung Gyoon; Choi, Yun-Young

    2011-01-01

    We investigate the dependence of occurrence of bars in galaxies on galaxy properties and environment. We use a volume-limited sample of 33,391 galaxies brighter than $M_{r}=-19.5+5$log$h$ at $0.02\\le z\\le0.05489$, drawn from the SDSS DR 7. We classify the galaxies into early and late types, and identify bars by visual inspection. Among 10,674 late-type galaxies with axis ratio $b/a>0.60$, we find 3,240 barred galaxies ($f_{bar}=30.4%$) which divide into 2,542 strong bars ($f_{SB1}=23.8%$) and 698 weak bars ($f_{SB2}=6.5%$). We find that $f_{SB1}$ increases as $u-r$ color becomes redder, and that it has a maximum value at intermediate velocity dispersion ($\\sigma\\simeq$150 km s$^{-1}$). This trend suggests that strong bars are dominantly hosted by intermediate-mass systems. Weak bars prefer bluer galaxies with lower mass and lower concentration. In the case of strong bars, their dependence on the concentration index appears only for massive galaxies with $\\sigma>150$ km s${}^{-1}$. We also find that $f_{bar}$ ...

  13. Finite Element Simulations to Explore Assumptions in Kolsky Bar Experiments.

    Energy Technology Data Exchange (ETDEWEB)

    Crum, Justin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-08-05

    The chief purpose of this project has been to develop a set of finite element models that attempt to explore some of the assumptions in the experimental set-up and data reduction of the Kolsky bar experiment. In brief, the Kolsky bar, sometimes referred to as the split Hopkinson pressure bar, is an experimental apparatus used to study the mechanical properties of materials at high strain rates. Kolsky bars can be constructed to conduct experiments in tension or compression, both of which are studied in this paper. The basic operation of the tension Kolsky bar is as follows: compressed air is inserted into the barrel that contains the striker; the striker accelerates towards the left and strikes the left end of the barrel producing a tensile stress wave that propogates first through the barrel and then down the incident bar, into the specimen, and finally the transmission bar. In the compression case, the striker instead travels to the right and impacts the incident bar directly. As the stress wave travels through an interface (e.g., the incident bar to specimen connection), a portion of the pulse is transmitted and the rest reflected. The incident pulse, as well as the transmitted and reflected pulses are picked up by two strain gauges installed on the incident and transmitted bars as shown. By interpreting the data acquired by these strain gauges, the stress/strain behavior of the specimen can be determined.

  14. The Structure of the Milky Way's Bar Outside the Bulge

    CERN Document Server

    Wegg, Christopher; Portail, Matthieu

    2015-01-01

    While it is incontrovertible that the inner Galaxy contains a bar, its structure near the Galactic plane has remained uncertain, where extinction from intervening dust is greatest. We investigate here the Galactic bar outside the bulge, the long bar, using red clump giant (RCG) stars from UKIDSS, 2MASS, VVV, and GLIMPSE. We match and combine these surveys to investigate a wide area in latitude and longitude, |b|<9deg and |l|<40deg. We find: (1) The bar extends to l~25deg at |b|~5deg from the Galactic plane, and to l~30deg at lower latitudes. (2) The long bar has an angle to the line-of-sight in the range (28-33)deg, consistent with studies of the bulge at |l|<10deg. (3) The scale-height of RCG stars smoothly transitions from the bulge to the thinner long bar. (4) There is evidence for two scale heights in the long bar. We find a ~180pc thin bar component reminiscent of the old thin disk near the sun, and a ~45pc super-thin bar component which exists predominantly towards the bar end. (5) Constructing...

  15. How can double-barred galaxies be long-lived?

    CERN Document Server

    Wozniak, Herve

    2015-01-01

    Double-barred galaxies account for almost one third of all barred galaxies, suggesting that secondary stellar bars, which are embedded in large-scale primary bars, are long-lived structures. However, up to now it has been hard to self-consistently simulate a disc galaxy that sustains two nested stellar bars for longer than a few rotation periods. N-body/hydrodynamical simulations including star formation recipes have been performed. Their properties have been compared with the most recent observational data in order to prove that they are representative of double-barred galaxies, even SB0. Overlaps in dynamical resonances and bar modes have been looked for using Fourier spectrograms. Double-barred galaxies have been successfully simulated with lifetimes as long as 7 Gyr. The stellar population of the secondary bar is younger on average than for the primary large-scale bar. An important feature of these simulations is the absence of any resonance overlap for several Gyr. In particular, there is no overlap betw...

  16. Obtention control bars patterns for a BWR using Tabo search; Obtencion de patrones de barras de control para un BWR usando busqueda Tabu

    Energy Technology Data Exchange (ETDEWEB)

    Castillo, A.; Ortiz, J.J.; Alonso, G. [Instituto Nacional de Investigaciones Nucleares, Km. 36.5 Carretera Mexico-Toluca, Ocoyoacac, Estado de Mexico 52045 (Mexico); Morales, L.B. [UNAM, IIMAS, Ciudad Universitaria, D. F. 04510 (Mexico); Valle, E. del [IPN, ESFM, Unidad Profesional ' Adolfo Lopez Mateos' , Col. Lindavista 07738, D. F. (Mexico)]. e-mail: jacm@nuclear.inin.mx

    2004-07-01

    The obtained results when implementing the technique of tabu search, for to optimize patterns of control bars in a BWR type reactor, using the CM-PRESTO code are presented. The patterns of control bars were obtained for the designs of fuel reloads obtained in a previous work, using the same technique. The obtained results correspond to a cycle of 18 months using 112 fresh fuels enriched at the 3.53 of U-235. The used technique of tabu search, prohibits recently visited movements, in the position that correspond to the axial positions of the control bars, additionally the tiempo{sub t}abu matrix is used for to manage a size of variable tabu list and the objective function is punished with the frequency of the forbidden movements. The obtained patterns of control bars improve the longitude of the cycle with regard to the reference values and they complete the restrictions of safety. (Author)

  17. Search for the decay of a B0 or B0bar meson to K*0bar K0 or K*0 K0bar

    Energy Technology Data Exchange (ETDEWEB)

    Aubert, B.

    2006-06-27

    The authors present a search for the decay of a B{sup 0} or {bar B}{sup 0} meson to a {bar K}*{sup 0} K{sup 0} or K*{sup 0} {bar K}{sup 0} final state, using a sample of approximately 232 million B{bar B} events collected with the BABAR detector at the PEP-II asymmetric energy e{sup +}e{sup -} collider at SLAC. The measured branching fraction is {Beta}(B{sup 0} {yields} {bar K}*{sup 0} K{sup 0}) + {Beta}(B{sup 0} {yields} K*{sup 0} {bar K}{sup 0}) = (0.2{sub -0.8, -0.3}{sup +0.9, +0.1}) x 10{sup -6}. They obtain the following upper limit for the branching fraction at 90% confidence level: {Beta}(B{sup 0} {yields} {bar K}*{sup 0} K{sup 0}) + {Beta}(B{sup 0} {yields} K*{sup 0} {bar K}{sup 0}) < 1.9 x 10{sup -6}. They use our result to constrain the Standard Model prediction for the deviation of the CP asymmetry in B{sup 0} {yields} {phi}K{sup 0} from sin 2{beta}.

  18. Labelling GM-free Products

    DEFF Research Database (Denmark)

    Punt, Maarten; Venus, Thomas; Wesseler, Justus

    2016-01-01

    Food suppliers in the EU must comply with labelling regulations for genetically modified organisms (GMOs). However, excluded from mandatory labelling are food products derived from animals fed with GM feed (mainly GM soybean in the EU). Because of this labelling exemption, consumers are unable to...

  19. Food Labels Tell the Story!

    Science.gov (United States)

    ... My World From the Label to the Table! Food Labels Tell the Story! What is in food? Food provides your body with all of the ... your food choices. Nutrition Facts—the Labels on Food Products Beginning in 1994, the US government began ...

  20. Predicting vertical jump height from bar velocity.

    Science.gov (United States)

    García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

    2015-06-01

    The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s(-2)). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r(2) = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r(2) = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key pointsVertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer.The relationship between the point at which bar acceleration is less than -9.81 m·s(-2) and the real take-off is affected by the velocity of movement.Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance.

  1. BarLaurean mahdollisuudet saavuttaa Joutsenmerkki

    OpenAIRE

    Järveläinen, Tuomas; Paavola, Salme

    2009-01-01

    Joutsenmerkki on vapaaehtoinen yhteispohjoismainen Ympäristömerkki. Opinnäytetyö on osa kehittämistyötä, jonka tavoitteena on hakea Joutsenmerkintää BarLaurean toiminnalle. Joutsenmerkin anomiseen tähtäävät toimenpiteet on aloitettu keväällä 2009 tekemällä aiheesta alustava toimintasuunnitelma. Opinnäytetyön tavoitteena on soveltaa käytäntöön toimintasuunnitelmassa kuvattuja toimenpiteitä, jotka dokumentoidaan Joutsenmerkkikansioon osana Joutsenmerkki-hakemusta. Opinnäytetyön tavoitteena ...

  2. CP Violation at BaBar

    Energy Technology Data Exchange (ETDEWEB)

    Yeche, Christophe; /DSM, DAPNIA, Saclay

    2011-11-15

    We report recent measurements of the three CKM angles of the Unitarity Triangle using about 383 millions b{bar b} pairs collected with the BABAR detector at the PEP-II asymmetric-energy B Factory at SLAC. The results of the angles ({beta}, {alpha}, {gamma}) of the unitarity triangle are consistent with Belle results, and with other CKM constraints such as the measurement of {epsilon}{sub K}, the length of the sides of the unitarity triangle determined from the measurements of {Delta}m{sub d}, {Delta}m{sub s}, |V{sub ub}|. This is an impressive confirmation of Standard Model in quark-flavor sector.

  3. Warp evidences in precessing galactic bar models

    OpenAIRE

    Sanchez-Martin, Patricia; Romero-Gomez, Merce; Masdemont, Josep J.

    2016-01-01

    Most galaxies have a warped shape when they are seen from an edge-on point of view. The reason for this curious form is not completely known so far and in this work we apply dynamical system tools to contribute to its explanation. Starting from a simple, but realistic, model formed by a bar and a disc, we study the effect produced by a small misalignment between the angular momentum of the system and its angular velocity. To this end, a precession model is developed and considered, assuming t...

  4. Predicting vertical jump height from bar velocity.

    Science.gov (United States)

    García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

    2015-06-01

    The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s(-2)). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r(2) = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r(2) = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key pointsVertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer.The relationship between the point at which bar acceleration is less than -9.81 m·s(-2) and the real take-off is affected by the velocity of movement.Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance. PMID:25983572

  5. A Distinct Structure Inside the Galactic Bar

    OpenAIRE

    Nishiyama, Shogo; Nagata, Tetsuya; Baba, Daisuke; Haba, Yasuaki; Kadowaki, Ryota; Kato, Daisuke; Kurita, Mikio; Nagashima, Chie; Nagayama, Takahiro; Murai, Yuka; Nakajima, Yasushi; Tamura, Motohide; Nakaya, Hidehiko; Sugitani, Koji; Naoi, Takahiro

    2005-01-01

    We present the result of a near-infrared (J H Ks) survey along the Galactic plane, -10.5deg < l < +10.5deg and b=+1.0deg, with the IRSF 1.4m telescope and the SIRIUS camera. Ks vs. H-Ks color-magnitude diagrams reveal a well-defined population of red clump (RC) stars whose apparent magnitude peak changes continuously along the Galactic plane, from Ks=13.4 at l=-10deg to Ks=12.2 at l=+10deg after dereddening. This variation can be explained by the bar-like structure found in previous studies, ...

  6. Myocardial arterial spin labeling

    OpenAIRE

    Kober, Frank; Jao, Terrence; Troalen, Thomas; Nayak, Krishna S.

    2016-01-01

    Arterial spin labeling (ASL) is a cardiovascular magnetic resonance (CMR) technique for mapping regional myocardial blood flow. It does not require any contrast agents, is compatible with stress testing, and can be performed repeatedly or even continuously. ASL-CMR has been performed with great success in small-animals, but sensitivity to date has been poor in large animals and humans and remains an active area of research. This review paper summarizes the development of ASL-CMR techniques, c...

  7. Three-Dimensional Analysis of Voids in AM60B Magnesium Tensile Bars Using Computed Tomography Imagery

    Energy Technology Data Exchange (ETDEWEB)

    Waters, A M

    2001-05-01

    In an effort to increase automobile fuel efficiency as well as decrease the output of harmful greenhouse gases, the automotive industry has recently shown increased interest in cast light metals such as magnesium alloys in an effort to increase weight savings. Currently several magnesium alloys such as AZ91 and AM60B are being used in structural applications for automobiles. However, these magnesium alloys are not as well characterized as other commonly used structural metals such as aluminum. This dissertation presents a methodology to nondestructively quantify damage accumulation due to void behavior in three dimensions in die-cast magnesium AM60B tensile bars as a function of mechanical load. Computed tomography data was acquired after tensile bars were loaded up to and including failure, and analyzed to characterize void behavior as it relates to damage accumulation. Signal and image processing techniques were used along with a cluster labeling routine to nondestructively quantify damage parameters in three dimensions. Void analyses were performed including void volume distribution characterization, nearest neighbor distance calculations, shape parameters, and volumetric renderings of voids in the alloy. The processed CT data was used to generate input files for use in finite element simulations, both two- and three-dimensional. The void analyses revealed that the overwhelming source of failure in each tensile bar was a ring of porosity within each bar, possibly due to a solidification front inherent to the casting process. The measured damage parameters related to void nucleation, growth, and coalescence were shown to contribute significantly to total damage accumulation. Void volume distributions were characterized using a Weibull function, and the spatial distributions of voids were shown to be clustered. Two-dimensional finite element analyses of the tensile bars were used to fine-tune material damage models and a three-dimensional mesh of an extracted

  8. Locally Orderless Registration Code

    DEFF Research Database (Denmark)

    2012-01-01

    This is code for the TPAMI paper "Locally Orderless Registration". The code requires intel threadding building blocks installed and is provided for 64 bit on mac, linux and windows.......This is code for the TPAMI paper "Locally Orderless Registration". The code requires intel threadding building blocks installed and is provided for 64 bit on mac, linux and windows....

  9. Study of the ρ-bar, β-bar and Λ parameters of a light-water reactor

    International Nuclear Information System (INIS)

    The kinetic and perturbation equations are derived from the time-dependent transport equation. Kinetic equations depend only on the ratios a = ρ-bar/β-bar and b = β-bar/Λ, which are definite, while the reactivity ρ-bar, the delayed neutron fraction (β-bar and the generation time Λ are expressed in terms of an arbitrary function I. The 'static' definitions of these parameters, which reduce kinetic problems to a set of purely term dependent equations, introduce the effective fraction β-bar. One way of determining experimentally the ratio b is presented; it consists in analysing the power transient after a rapid variation of the reactivity, caused by the implosion of an empty glass-bull. A simple interpretation is proposed. The apparatus can be transformed easily into a reactimeter. The value of the effective delayed neutron fraction β-bar has been determined by averaging the reactivity effects of a copper sheet through out the reactor core. Experimental results: b = β-bar/Λ = 129 s-1 and β-bar 795.10-5, have been determined on a light-water moderated, enriched-uranium fuelled reactor. The calculated values of the effectiveness of delayed neutrons γ β-bar/β 1.23 and the generation time Λ 59.10-6s agrees fairly well with the experimental results. (author)

  10. Automated multisyringe stir bar sorptive extraction using robust montmorillonite/epoxy-coated stir bars.

    Science.gov (United States)

    Ghani, Milad; Saraji, Mohammad; Maya, Fernando; Cerdà, Víctor

    2016-05-01

    Herein we present a simple, rapid and low cost strategy for the preparation of robust stir bar coatings based on the combination of montmorillonite with epoxy resin. The composite stir bar was implemented in a novel automated multisyringe stir bar sorptive extraction system (MS-SBSE), and applied to the extraction of four chlorophenols (4-chlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol and pentachlorophenol) as model compounds, followed by high performance liquid chromatography-diode array detection. The different experimental parameters of the MS-SBSE, such as sample volume, selection of the desorption solvent, desorption volume, desorption time, sample solution pH, salt effect and extraction time were studied. Under the optimum conditions, the detection limits were between 0.02 and 0.34μgL(-1). Relative standard deviations (RSD) of the method for the analytes at 10μgL(-1) concentration level ranged from 3.5% to 4.1% (as intra-day RSD) and from 3.9% to 4.3% (as inter-day RSD at 50μgL(-1) concentration level). Batch-to-batch reproducibility for three different stir bars was 4.6-5.1%. The enrichment factors were between 30 and 49. In order to investigate the capability of the developed technique for real sample analysis, well water, wastewater and leachates from a solid waste treatment plant were satisfactorily analyzed. PMID:27062720

  11. The LHCb pentaquark as a $\\bar{D}^*\\Sigma_c-\\bar{D}^*\\Sigma_c^*$ molecular state

    CERN Document Server

    Roca, L; Oset, E

    2015-01-01

    We perform a theoretical analysis of the $\\Lambda_b \\to J/\\psi K^- p$ reaction from where a recent LHCb experiment extracts a $\\Lambda(1405)$ contribution in the $K^- p$ spectrum close to threshold and two baryon states of hidden charm in the $J/\\psi\\,p$ spectrum. We recall that baryon states of this type have been theoretically predicted matching the mass, width and $J^P$ of the experiment, concretely some states built up from the $J/\\psi\\, N$, $\\bar D^* \\Lambda_c$, $\\bar D^* \\Sigma_c$, $\\bar D \\Sigma^*_c$ and $\\bar D^* \\Sigma^*_c$ coupled channels. We assume that the observed narrow state around 4450 MeV has this nature and we are able to describe simultaneously the shapes and relative strength of the the $K^- p$ mass distribution close to threshold and the peak of the $J/\\psi\\,p$ distribution, with values of the $J/\\psi\\, p$ coupling to the resonance in line with the theoretical ones. The non trivial matching of many properties gives support to a $J^P=3/2^-$ assignment to this state and to its nature as a ...

  12. Automated multisyringe stir bar sorptive extraction using robust montmorillonite/epoxy-coated stir bars.

    Science.gov (United States)

    Ghani, Milad; Saraji, Mohammad; Maya, Fernando; Cerdà, Víctor

    2016-05-01

    Herein we present a simple, rapid and low cost strategy for the preparation of robust stir bar coatings based on the combination of montmorillonite with epoxy resin. The composite stir bar was implemented in a novel automated multisyringe stir bar sorptive extraction system (MS-SBSE), and applied to the extraction of four chlorophenols (4-chlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol and pentachlorophenol) as model compounds, followed by high performance liquid chromatography-diode array detection. The different experimental parameters of the MS-SBSE, such as sample volume, selection of the desorption solvent, desorption volume, desorption time, sample solution pH, salt effect and extraction time were studied. Under the optimum conditions, the detection limits were between 0.02 and 0.34μgL(-1). Relative standard deviations (RSD) of the method for the analytes at 10μgL(-1) concentration level ranged from 3.5% to 4.1% (as intra-day RSD) and from 3.9% to 4.3% (as inter-day RSD at 50μgL(-1) concentration level). Batch-to-batch reproducibility for three different stir bars was 4.6-5.1%. The enrichment factors were between 30 and 49. In order to investigate the capability of the developed technique for real sample analysis, well water, wastewater and leachates from a solid waste treatment plant were satisfactorily analyzed.

  13. Shepherding Tidal Debris with the Galactic Bar: The Ophiuchus Stream

    CERN Document Server

    Hattori, Kohei; Sanders, Jason L

    2015-01-01

    The dynamics of stellar streams in rotating barred potentials is explained for the first time. Naturally, neighbouring stream stars reach pericentre at slightly different times. In the presence of a rotating bar, these neighbouring stream stars experience different bar orientations during pericentric passage and hence each star receives a different torque from the bar. These differing torques reshape the angular momentum and energy distribution of stars in the stream, which in turn changes the growth rate of the stream. For a progenitor orbiting in the same sense as the bar's rotation and satisfying a resonance condition, the resultant stream can be substantially shorter or longer than expected, depending on whether the pericentric passages of the progenitor occur along the bar's minor or major axis respectively. We present a full discussion of this phenomenon focusing mainly on streams confined to the Galactic plane. In stark contrast with the evolution in static potentials, which give rise to streams that g...

  14. Bar pattern speed evolution over the last 7 Gyr

    Science.gov (United States)

    Pérez, I.; Aguerri, J. A. L.; Méndez-Abreu, J.

    2012-04-01

    Context. The tumbling pattern of a bar is the main parameter characterising its dynamics. From numerical simulations, its evolution since bar formation is tightly linked to the dark halo in which the bar is formed through dynamical friction and angular momentum exchange. Observational measurements of the bar pattern speed with redshift can restrict models of galaxy formation and bar evolution. Aims: We aim to determine for the first time the bar pattern speed evolution with redshift based on morphological measurements. Methods: We have selected a sample of 44 low-inclination ringed galaxies from the SDSS and COSMOS surveys covering the redshift range 0 electronic form at http://www.aanda.orgBased on observations made with the NASA/ESA Hubble Space Telescope, obtained from the data archive at the Space Telescope Science Institute. STScI is operated by the Association of Universities for Research in Astronomy, Inc. under NASA contract NAS 5-26555.

  15. Uncertainties in the Deprojection of the Observed Bar Properties

    CERN Document Server

    Zou, Yanfei; Li, Zhao-Yu

    2014-01-01

    In observations, it is important to deproject the two fundamental quantities characterizing a bar, i.e., its length ($a$) and ellipticity ($e$), to face-on values before any careful analyses. However, systematic estimation on the uncertainties of the commonly used deprojection methods is still lacking. Simulated galaxies are well suited in this study. We project two simulated barred galaxies onto a 2D plane with different bar orientations and disk inclination angles ($i$). Bar properties are measured and deprojected with the popular deprojection methods in the literature. Generally speaking, deprojection uncertainties increase with increasing $i$. All the deprojection methods behave badly when $i$ is larger than $60^\\circ$, due to vertical thickness of the bar. Thus, future statistical studies of barred galaxies should exclude galaxies more inclined than $60^\\circ$. At moderate inclination angles ($i\\leq60^\\circ$), 2D deprojection methods (analytical and image stretching) and Fourier-based methods (Fourier de...

  16. Anti-seismic behavior of HRB400 reinforced steel bars

    Institute of Scientific and Technical Information of China (English)

    QIN Bin; SHENG Guang-min; GONG Shi-hong

    2005-01-01

    The properties of anti-seismic HRB400 steel bars with 25 mm diameter were systematically investigated. The results showed that the properties of the HRB400 reinforced steel bars had been greatly enhanced comparing with HRB335 steel bars, i.e. coordination of strength and ductility, strain-aging sensibility, low temperature impact toughness, weld ability and high strain low cycle fatigue. The ductile-brittle transit temperatures of hot-rolled and strain-aged steel bars were evaluated as -17℃ and-8℃ respectively, and the low temperature impact toughness of HRB400 steel bars remains to be improved. Transmission electron microscopy (TEM) and electron diffraction showed little vanadium existed in ferrite as VN, most of which existed in pearlite as alloy cementite which resulted in the declination of impact toughness. Methods were suggested to improve the anti-seismic properties of steel bars.

  17. Asymptotic Orbits in Barred Spiral Galaxies

    CERN Document Server

    Harsoula, Maria; Contopoulos, George

    2010-01-01

    We study the formation of the spiral structure of barred spiral galaxies, using an $N$-body model. The evolution of this $N$-body model in the adiabatic approximation maintains a strong spiral pattern for more than 10 bar rotations. We find that this longevity of the spiral arms is mainly due to the phenomenon of stickiness of chaotic orbits close to the unstable asymptotic manifolds originated from the main unstable periodic orbits, both inside and outside corotation. The stickiness along the manifolds corresponding to different energy levels supports parts of the spiral structure. The loci of the disc velocity minima (where the particles spend most of their time, in the configuration space) reveal the density maxima and therefore the main morphological structures of the system. We study the relation of these loci with those of the apocentres and pericentres at different energy levels. The diffusion of the sticky chaotic orbits outwards is slow and depends on the initial conditions and the corresponding Jaco...

  18. Barómetro industrial LEON 50

    Directory of Open Access Journals (Sweden)

    Javier Álvarez Martínez

    2005-12-01

    Full Text Available El Barómetro indusrial LEON 50 es un trabajo de investigación que tiene como objetivo esencial identificar características patrimoniales, financieras y económicas de una muestra de empresas que actúan dentro de la industria leonesa. El soporte de este estudio empírico es la información contable anual auditada que depositan en el Registro Mercantil las empresas integrantes de la muestra, recogida básicamente en el balance de situación, la cuenta de pérdidas y ganacias y el cuadro de finaciación referidos al bienio 2001-02. En esencia, el Barómetro Industrial LEON 50 pretende ser un avance en el análisis, diagnóstico y mejor conocimiento de la industria regional, aportando una visión actualizada sobre estrategias y pautas de actuación empresarial que serán objeto de observación en períodos

  19. Polyphase alternating codes

    CERN Document Server

    Markkanen, Markku

    2007-01-01

    This work introduces a method for constructing polyphase alternating codes in which the length of a code transmission cycle can be $p^m$ or $p-1$, where $p$ is a prime number and $m$ is a positive integer. The relevant properties leading to the construction alternating codes and the algorithm for generating alternating codes is described. Examples of all practical and some not that practical polyphase code lengths are given.

  20. Constructing quantum codes

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Quantum error correcting codes are indispensable for quantum information processing and quantum computation.In 1995 and 1996,Shor and Steane gave first several examples of quantum codes from classical error correcting codes.The construction of efficient quantum codes is now an active multi-discipline research field.In this paper we review the known several constructions of quantum codes and present some examples.

  1. Interaction of Bar Morphology and Riparian Vegetation in Gravel-Bed Rivers

    Science.gov (United States)

    Francalanci, S.; Bertoldi, W.; Siviglia, A.; Solari, L.; Toffolon, M.; Vetsch, D.

    2013-12-01

    Gravel-bed rivers are often characterized by complex bed topography, including single- and multiple-row alternate bars, bed undulations associated with channel curvature, riffle and pool sequences, presence of riparian vegetation in the floodplain, etc. The interaction of these features results in different morphologies with complex patterns and dynamics. The present work investigates the effect of the riparian vegetation on the bar dynamics, in particular it is investigated how the vegetation, which grows during the dry season on the bars, can alter the topographic patterns evolution during flood conditions. Performing two-dimensional numerical simulations we try to answer to the following research questions: which is the interaction of vegetation with bar morphology? which are the changes in sediment discharge and flow resistance, at cross-sectional and reach scale? Which are the changes in distribution of emerged and submerged areas, and potential feedbacks for vegetation growth? Which is the effect of vegetation on bar wave-length? The code BASEMENT (Faeh et al., 2010) has been used for performing the numerical runs. It has been properly modified in order to deal with the numerical description of the vegetation. The vegetation was allowed to grow during the dry season on the top of dry emergent areas, and the vertical distribution of vegetation in equilibrium condition was modeled as a function of the bed elevation using a simple analytical formulation, following Marani et al (2013). Then, during the flood events we assume that the vegetation distribution does not change, and that it can only be uprooted if the bed is eroded.The flow resistance was divided into a resistance exerted by the soil and a resistance exerted by the plants (Crosato and Saleh, 2010; Li and Millar, 2011); in this way it was possible to reproduce both the decrease in bed shear stress, reducing the sediment transport capacity of the flow within the plants, and the increase in hydraulic

  2. STABILIZER BARS – CALCULATIONS, CONSTRUCTION AND PRODUCTION METHODS

    Directory of Open Access Journals (Sweden)

    Adam Marek WITTEK

    2015-06-01

    Full Text Available The article outlines the calculation and production methods for stabilizer bars. Modern technological and structural solutions in contemporary cars are reflected also in the construction and manufacturing of stabilizer bars. A proper construction and the selection of parameters influence the strength properties, the weight, durability and reliability as well as the selection of an appropriate production method. The selection of the manufacturing process has a fundamental impact on the quality and durability of the stabilizer bars.

  3. Fault bars and the risk of feather damage in cranes

    OpenAIRE

    Jovani, Roger; Blas, Julio; Stoffel, M.J.; Bortolotti, L.E.; Bortolotti, Gary R.

    2010-01-01

    Fault bars are translucent areas across feathers grown under stressful conditions. They are ubiquitous across avian species and feather tracts. Because fault bars weaken feather structure and can lead to feather breakage, they may reduce flight performance and lower fitness. Therefore, natural selection might prime mechan- isms aimed at reducing the cost of fault bars, penalizing their occurrence in those feathers more relevant for flight. Here, we tested one prediction of this ‘fault...

  4. Principles and Practices of Bar and Beverage Management

    OpenAIRE

    Murphy, James Peter

    2013-01-01

    Principles and Practices of Bar and Beverage Management is a comprehensive text and resource book designed to explain the latest developments and new complexities of managing modern bars - be they stand alone or part of larger institutions such as hotels and resorts. Consumer expectations have changed, and a bar today must deliver an integrated social experience in a safe modern environment, which also offers the latest products and services in a professional and engaging fashion. Against ...

  5. The structure of the Milky Way's bar outside the bulge

    Science.gov (United States)

    Wegg, Christopher; Gerhard, Ortwin; Portail, Matthieu

    2015-07-01

    While it is incontrovertible that the inner Galaxy contains a bar, its structure near the Galactic plane has remained uncertain, where extinction from intervening dust is greatest. We investigate here the Galactic bar outside the bulge, the long bar, using red clump giant (RCG) stars from United Kingdom Infrared Deep Sky Survey, Two Micron All Sky Survey, Vista Variables in the Via Lactea and Galactic Legacy Infrared Midplane Survey Extraordinaire. We match and combine these surveys to investigate a wide area in latitude and longitude, |b| ≤ 9° and |l| ≤ 40°. We find (i) the bar extends to l ˜ 25° at |b| ˜ 5° from the Galactic plane, and to l ˜ 30° at lower latitudes; (ii) the long bar has an angle to the line-of-sight in the range (28°-33°), consistent with studies of the bulge at |l| thin bar component reminiscent of the old thin disc near the Sun, and a ˜45 pc superthin bar components which exist predominantly towards the bar end; (v) constructing parametric models for the red clump magnitude distributions, we find a bar half-length of 5.0 ± 0.2 kpc for the two-component bar, and 4.6 ± 0.3 kpc for the thin bar component alone. We conclude that the Milky Way contains a central box/peanut bulge which is the vertical extension of a longer, flatter bar, similar as seen in both external galaxies and N-body models.

  6. Washing with contaminated bar soap is unlikely to transfer bacteria.

    OpenAIRE

    Heinze, J. E.; Yackovich, F.

    1988-01-01

    Recent reports of the isolation of microorganisms from used soap bars have raised the concern that bacteria may be transferred from contaminated soap bars during handwashing. Since only one study addressing this question has been published, we developed an additional procedure to test this concern. In our new method prewashed and softened commercial deodorant soap bars (0.8% triclocarban) not active against Gram-negative bacteria were inoculated with Escherichia coli and Pseudomonas aeruginos...

  7. Kolkata Restaurant Problem as a Generalised El Farol Bar Problem

    Science.gov (United States)

    Chakrabarti, Bikas K.

    Generalisation of the El Farol bar problem to that of many bars here leads to the Kolkata restaurant problem, where the decision to go to any restaurant or not is much simpler (depending on the previous experience of course, as in the El Farol bar problem). This generalised problem can be exactly analysed in some limiting cases discussed here. The fluctuation in the restaurant service can be shown to have precisely an inverse cubic behavior, as widely seen in the stock market fluctuations.

  8. Linerless label device and method

    KAUST Repository

    Binladen, Abdulkari

    2016-01-14

    This apparatus and method for applying a linerless label to an end user product includes a device with a printer for printing on a face surface of a linerless label, and a release coat applicator for applying a release coat to the face surface of the label; another device including an unwinder unit (103) to unwind a roll of printed linerless label; a belt (108); a glue applicator (102) for applying glue to the belt; a nip roller (106) for contacting and applying pressure to the face surface of the linerless label such that the glue on the belt transfers to the back surface of the linerless label; at least one slitting knife 105) positioned downstream the belt and a rewinder unit (104) positioned downstream the slitting knife; and a third device which die cuts and applies the linerless label to an end user object.

  9. Preliminary systems-interaction results from the Digraph Matrix Analysis of the Watts Bar Nuclear Power Plant safety-injection systems

    Energy Technology Data Exchange (ETDEWEB)

    Sacks, I.J.; Ashmore, B.C.; Champney, J.M.; Alesso, H.P.

    1983-06-01

    This report provides preliminary results generated by a Digraph Matrix Analysis (DMA) for a Systems Interaction analysis performed on the Safety Injection System of the Tennessee Valley Authority Watts Bar Nuclear Power Plant. An overview of DMA is provided along with a brief description of the computer codes used in DMA.

  10. Label-Guided Graph Exploration with Adjustable Ratio of Labels

    CERN Document Server

    Zhang, Meng; Tang, Jijun

    2012-01-01

    The graph exploration problem is to visit all the nodes of a connected graph by a mobile entity, e.g., a robot. The robot has no a priori knowledge of the topology of the graph or of its size. Cohen et al. \\cite{Ilcinkas08} introduced label guided graph exploration which allows the system designer to add short labels to the graph nodes in a preprocessing stage; these labels can guide the robot in the exploration of the graph. In this paper, we address the problem of adjustable 1-bit label guided graph exploration. We focus on the labeling schemes that not only enable a robot to explore the graph but also allow the system designer to adjust the ratio of the number of different labels. This flexibility is necessary when maintaining different labels may have different costs or when the ratio is pre-specified. We present 1-bit labeling (two colors, namely black and white) schemes for this problem along with a labeling algorithm for generating the required labels. Given an $n$-node graph and a rational number $\\rh...

  11. Comparing photometric results of real and N-body bars

    CERN Document Server

    Athanassoula, E; Carrasco, L; Bosma, A; De Souza, R E; Recillas, E

    2009-01-01

    We compare the results of the photometrical analysis of barred galaxies with those of a similar analysis from N-body simulations. The photometry is for a sample of nine barred galaxies observed in the J and Ks bands with the CANICA near infrared (NIR) camera at the 2.1-m telescope of the Observatorio Astrofisico Guillermo Haro (OAGH) in Cananea, Sonora, Mexico. The comparison includes radial ellipticity profiles and surface brightness (density for the N-body galaxies) profiles along the bar major and minor axes. We find very good agreement, arguing that the exchange of angular momentum within the galaxy plays a determinant role in the evolution of barred galaxies.

  12. Stability of cassava flour-based food bars

    Directory of Open Access Journals (Sweden)

    Erica Caroline da Silva

    2013-03-01

    Full Text Available The consumption of Brazilian cassava has been reduced due to a lack of adjustment to the modern lifestyle. To reverse this trend, new products could be developed specifically targeted to high-value niche markets. Cereal bars stand out as fast food high in nutritional value. A bar formula mimicking cereal bars was prepared using a mixture of Brazilian cassava flour, hydrogenated vegetable fat, dried bananas, ground cashew nuts, and glucose syrup. After being pressed, the bars were dried for 1 hour at 65 °C, packaged in films, and stored under ambient conditions. Its stability was continuously monitored for 210 days in order to ensure its safety and enable its introduction to the market. Texture loss was observed in the packed bars after 90 days of storage, but the sensory characteristics allowed the testers to perceive this tendency after only 30 days of storage. However, chemical, physical, and microbial analyses confirmed that the bars were safe for consumption for 180 days. The results showed that a 45 g cassava flour-based bar enriched with nuts and dried fruits can meet 6% of the recommended daily fiber intake with a caloric value between that of the common cereal bar and that of an energy bar. Adapting the formula with ingredients (fruits, nuts from different regions of Brazil may add value to this traditional product as a fast food.

  13. Musculoskeletal demands of progressions for the longswing on high bar.

    Science.gov (United States)

    Irwin, Gareth; Kerwin, David G

    2007-09-01

    Kinetic analyses of the chalked bar longswing on high bar and its associated progressions were used to explain musculoskeletal contributions during the performance of these skills. Data on four international male gymnasts performing three series of chalked bar longswings and eight progressions were recorded. Customized body segment inertia parameters, two-dimensional kinematics (50 Hz), and bar forces (1000 Hz) were used as input to inverse dynamic modelling. The analysis focused on the relative contributions of the knees, hips, and shoulders with root mean squared differences between the chalked bar longswing and the progressions being used to rank the progressions. Seventy per cent of the total work occurred between 200 degrees and 240 degrees of angular rotation in the longswing, 67% of which was contributed by the shoulders. The shoulders were also dominant in all progressions, with the largest such contribution occurring in the looped bar longswing with "no action". The least similar progression was the looped bar pendulum swing, while the most similar was the chalked bar bent knee longswing. This study provides a useful means for ranking progressions based on their kinetic similarity to the chalked bar longswing and builds on earlier research in identifying that progressions can be classified into those similar in physical demand (kinetics) and those similar in geometry (kinematics).

  14. Strain analysis of nonlocal viscoelastic Kelvin bar in tension

    Institute of Scientific and Technical Information of China (English)

    ZHAO Xue-chuan; LEI Yong-jun; ZHOU Jian-ping

    2008-01-01

    Based on viscoelastic Kelvin model and nonlocal relationship of strain and stress, a nonlocal constitutive relationship of viscoelasticity is obtained and the strain response of a bar in tension is studied. By transforming governing equation of the strain analysis into Volterra integration form and by choosing a symmetric exponential form of kernel function and adapting Neumann series, the closed-form solution of strain field of the bar is obtained. The creep process of the bar is presented. When time approaches infinite, the strain of bar is equal to the one of nonlocal elasticity.

  15. Shanghai’s Bars:Urban Romance and Sadness

    Institute of Scientific and Technical Information of China (English)

    LiuSha

    2002-01-01

    When speaking of Shanghai’s bars, what comes to people’s minds first must be Hengshan Street, a road known for its variety of bars. For many people, Hengshan Street is a landmark. On this street, bars in bold and unrestrained styles appeal to visitors. In fact, the whole street is a large open bar: the hurly-burly of "Hello" permeates every corner of the street; the resonant singing of "Rainbow Potato" echoes in the night sky; the rock’n roll of "Full House" fascinates passers-by with the wildness of John Lennon; even

  16. Measurement of the B0-bar Lifetime and the B0B0-bar Oscillation Frequency Using Partially Reconstructed B0-bar to D*+ l- nu-bar Decays

    Energy Technology Data Exchange (ETDEWEB)

    Aubert, B.; Barate, R.; Boutigny, D.; Couderc, F.; Karyotakis, Y.; Lees, J.P.; Poireau, V.; Tisserand, V.; Zghiche, A.; /Annecy, LAPP; Grauges, E.; /Barcelona, IFAE; Palano, A.; Pappagallo, M.; Pompili, A.; /Bari U. /INFN, Bari; Chen, J.C.; Qi, N.D.; Rong, G.; Wang, P.; Zhu, Y.S.; /Beijing, Inst. High Energy Phys.; Eigen, G.; Ofte, I.; Stugu, B.

    2005-07-27

    The authors present a simultaneous measurement of the {bar B}{sup 0} lifetime {tau}{sub B{sup 0}} and B{sup 0}{bar B}{sup 0} oscillation frequency {Delta}m{sub d}. We use a sample of about 50,000 partially reconstructed {bar B}{sup 0} {yields} D*{sup +}{ell}{sup -}{bar {nu}}{sub {ell}} decays identified with the BABAR detector at the PEP-II e{sup +}e{sup -} storage ring at SLAC. The flavor of the other B meson in the event is determined from the charge of another high-momentum lepton.

  17. Multipacting Analysis of the Superconducting Parallel-bar Cavity

    Energy Technology Data Exchange (ETDEWEB)

    S.U. De Silva, J.R. Delayen,

    2011-03-01

    The superconducting parallel-bar cavity is a deflecting/crabbing cavity with attractive properties, compared to other conventional designs, that is being considered for a number of applications. Multipacting can be a limiting factor to the performance of in any superconducting structure. In the parallel-bar cavity the main contribution to the deflection is due to the transverse deflecting voltage, between the parallel bars, making the design potentially prone to multipacting. This paper presents the results of analytical calculations and numerical simulations of multipacting in the parallel-bar cavity with resonant voltage, impact energies and corresponding particle trajectories.

  18. ANALISIS LABELLING PEREMPUAN DENGAN TEORI FEMINISME PSIKOANALISIS: STUDI KASUS MAJALAH REMAJA OLGA!

    Directory of Open Access Journals (Sweden)

    - Muashomah

    2013-04-01

    Full Text Available Labelling perempuan dalam majalah remaja merupakan salah satu tindakan media yang merugikan perempuan. Dalam tulisan ini, penulis mengkaji label-label perempuan, bentuk labelling, analisis teori feminisme psikoanalisis terhadap labelling untuk perempuan dalam majalah remaja. Dalam penelitian ini penulis menggunakan metode semiotik dan penelitian dilakukan terhadap majalah Olga. Hasil penelitian menunjukkan bahwa praktek pelabelan terhadap perempuan yang dilakukan oleh majalah remaja ditujukan untuk remaja perempuan dilakukan dengan empat kode yaitu tubuh seksi dan wajah cantik, pentingnya penampilan bagi perempuan, kondisi psikologis perempuan yang labil, dan peran domestik perempuan. Label-label ini dapat membentuk persepsi masyarakat tentang perempuan dan mengandung konsekuensi pengharapan kepada perempuan. Penelitian ini menguatkan lagi tesis bahwa perempuan sering menjadi objek pelabelan. Label-label ini berasal dari kehidupan sosial perempuan dan diinternalisasi oleh perempuan.Labelling in woman in teenagers magazine is one of the mass media strategy that can harm woman. Even though women normally do not recognize it. The purpose of this research is to describe the labelling practices in media analysed with the psychoanalysis feminism theory. The research method used is semiotics and the research is conducted on Olga! maganize. Result from the research shows that  the labelling targets teenagers through four labelling codes: sexy body and beautiful face; the importance physical performance for women; unconsistent psycological condition; and domestic role of women. This label constructs society perception on  woman. The study strengthen a thesis that woman tends to be a labelling object. These labels are developped from women’s social life and are internalized by women

  19. The Quark Flavor Violating Higgs Decay $h \\rightarrow \\bar b s + b \\bar s$ in the MSSM

    CERN Document Server

    Gómez, M E; Rehman, M

    2015-01-01

    We study the quark flavor violating Higgs-boson decay $h \\rightarrow \\bar b s + b \\bar s$ in the Minimal Supersymmetric Standard Model (MSSM). The decay is analyzed first in a model independent, and in a second step in the minimal flavor violationg (MFV) Constrained MSSM. The experimental constraints from $B$-Physics observables (BPO) and electroweak precision observables (EWPO) are also calculated and imposed on the parameter space. It is shown that in some cases the EWPO restrict the flavor violating parameter space stronger than the BPO. In the model independent analysis values of ${\\cal O}(10^{-4})$ can be found for ${\\rm BR}(h \\rightarrow \\bar b s + b \\bar s)$. In the MFV CMSSM such results can only be obtained in very restricted parts of the parameter space. The results show that it is not excluded to observe the decay $h \\rightarrow \\bar b s + b \\bar s$ in the MSSM at future $e^+e^-$ colliders.

  20. Kondo effect of $\\bar{D}_{s}$ and $\\bar{D}_{s}^{\\ast}$ mesons in nuclear matter

    CERN Document Server

    Yasui, Shigehiro

    2016-01-01

    We study the Kondo effect for $\\bar{D}_{s}$ and $\\bar{D}_{s}^{\\ast}$ mesons as impurity particles in nuclear matter. The spin-exchange interaction between the $\\bar{D}_{s}$ or $\\bar{D}_{s}^{\\ast}$ meson and the nucleon induces the enhancement of the effective coupling in the low-energy scattering in the infrared region, whose scale of singularity is given by the Kondo scale. We investigate the Kondo scale in the renormalization group equation at nucleon one-loop level. We furthermore study the ground state with the Kondo effect in the mean-field approach, and present that the Kondo scale is related to the mixing strength between the $\\bar{D}_{s}$ or $\\bar{D}_{s}^{\\ast}$ meson and the nucleon in nuclear matter. We show the spectral function of the impurity when the Kondo effect occurs.

  1. New strategies of reloads design and models of control bars in boiling water reactors

    International Nuclear Information System (INIS)

    In this work the results obtained when analyzing new strategies in the reload designs of nuclear fuel and models of control bars, for boiling water reactors are presented. The idea is to analyze the behaviour of the reactor during an operation cycle, when the heuristic rules are not used (commonly used by expert engineers in both designs). Specifically was analyzed the rule of low leak and the load strategy Control Cell Core for the design of a fuel reload. In a same way was analyzed the rule of prohibiting the use of the intermediate positions in the control bars, as well as the construction of bar models based on load strategies type Control Cell Core. In the first analysis a balance and transition cycle were used. For the second analysis only a transition cycle was used, firstly with the reloads designed in the first analysis and later on with reloads built by other methods. For the simulation of the different configurations proposed in both cases, was used the code Simulate-3. To obtain the designs in both studies, the heuristic techniques or neural networks and taboo search were used. The obtained results show that it can be omitted of some rules used in the ambit for the mentioned designs and even so to obtain good results. To carry out this investigation was used Dell work station under Li nux platform. (Author)

  2. Labelled compounds. (Pt. B)

    International Nuclear Information System (INIS)

    Since the end of World War II there has been a tremendous increase in the number of compounds that have been synthesized with radioactive or stable isotopes. They have found application in many diverse fields, so much so, that hardly a single area in pure and applied science has not benefited. Not surprisingly it has been reflected in appearance of related publications. The early proceedings of the Symposia on Advances in Trace Methodology were soon followed by various Euratom sponsored meetings in which methods of preparing and storing labelled compounds featured prominently. In due course a resurgence of interest in stable isotopes, brought about by their greater availability (also lower cost) and partly by development of new techniques such as gas chromatography - mass spectrometry (gc-ms), led to the publication of proceedings of several successful conferences. More recently conferences dealing with the synthesis and applications of isotopes and isotopically labelled compounds have been established on a regular basis. In addition to the proceedings of conferences and journal publications individuals left their mark by producing definitive texts, usually on specific nuclides. Only the classic two volume publication of Murray and Williams (Organic syntheses with isotopes, New York 1985), now over 30 years old and out of print, attempted to do justice to several nuclides. With the large amount of work that has been undertaken since then it seems unlikely that an updated edition could be produced. The alternative strategy was to ask scientists currently active to review specific areas and this is the approach adopted in the present series of monographs. In this way it is intended to cover the broad advances that have been made in the synthesis and applications of isotopes and isotopically labelled compounds in the physical and biomedical sciences. (author). refs.; figs.; tabs

  3. Turbo Codes Extended with Outer BCH Code

    DEFF Research Database (Denmark)

    Andersen, Jakob Dahl

    1996-01-01

    The "error floor" observed in several simulations with the turbo codes is verified by calculation of an upper bound to the bit error rate for the ensemble of all interleavers. Also an easy way to calculate the weight enumerator used in this bound is presented. An extended coding scheme is proposed...

  4. Waisda?: video labeling game

    OpenAIRE

    Hildebrand, Michiel; Brinkerink, M.; Gligorov, R.; Steenbergen, Van; Huijkman, J.; Oomen, J.

    2013-01-01

    The Waisda? video labeling game is a crowsourcing tool to collect user-generated metadata for video clips. It follows the paradigm of games-with-a-purpose, where two or more users play against each other by entering tags that describe the content of the video. Players score points by entering the same tags as one of the other players. As a result each video that is played in the game is annotated with tags that are anchored to a time point in the video. Waisda? has been deployed in two projec...

  5. A Food Labeling

    Science.gov (United States)

    ... " ﻗﺎﻧﻮن اﻟﺒﻄﺎﻗﺎت واﻟﺘﻮﻋﻴﺔ اﻟﻐﺬاﺋﻴﺔ " [ Nutrition Labeling and Education Act ... ﻟﻠﻌﺼﻴﺮ اﻟﻤﻜﻮن ﺑﺈﺿﺎﻓﺔ اﻟﻤﺎء إﻟﻰ ﺧﻼﺻﺔ ﻣﺮآﺰة : ﻳﺠﺮى اﻟﺤﺴﺎب ﻣﻦ ﺟﺪول Brix ﻓﻲ 21 CFR 101.30(h)(1) ...

  6. Probe $\\Lambda - \\bar{\\Lambda}$ oscillation in $J/\\psi \\rightarrow \\Lambda\\,\\bar\\Lambda$ decay at BES-III

    OpenAIRE

    Kang, X. W.; H.B. Li; Lu, G. R.

    2010-01-01

    We discuss the possible searching for the oscillation by coherent $\\Lambda\\bar{\\Lambda}$ production in $J/\\psi \\rightarrow \\Lambda \\bar{\\Lambda}$ decay process. The sensitivity of measurement of $\\Lambda - \\bar{\\Lambda}$ oscillation in the external field at BES-III experiment is considered. These considerations indicate an alternative way to probe the $\\Delta B =2$ amplitude in addition to neutron oscillation experiments. Both coherent and time-dependent information can be used to extract $\\L...

  7. Study of J/psi -> p(p)over-bar and J/psi -> n(n)over-bar

    NARCIS (Netherlands)

    Ablikim, M.; Achasov, M. N.; Ambrose, D. J.; An, F. F.; An, Q.; An, Z. H.; Bai, J. Z.; Ban, Y.; Becker, J.; Berger, N.; Bertani, M.; Bian, J. M.; Boger, E.; Bondarenko, O.; Boyko, I.; Briere, R. A.; Bytev, V.; Cai, X.; Calcaterra, A.; Cao, G. F.; Chang, J. F.; Chelkov, G.; Chen, G.; Chen, H. S.; Chen, J. C.; Chen, M. L.; Chen, S. J.; Chen, Y.; Chen, Y. B.; Cheng, H. P.; Chu, Y. P.; Cronin-Hennessy, D.; Dai, H. L.; Dai, J. P.; Dedovich, D.; Deng, Z. Y.; Denig, A.; Denysenko, I.; Destefanis, M.; Ding, W. M.; Ding, Y.; Dong, L. Y.; Dong, M. Y.; Du, S. X.; Fang, J.; Fang, S. S.; Fava, L.; Feldbauer, F.; Feng, C. Q.; Ferroli, R. B.; Fu, C. D.; Fu, J. L.; Gao, Y.; Geng, C.; Goetzen, K.; Gong, W. X.; Gradl, W.; Greco, M.; Gu, M. H.; Gu, Y. T.; Guan, Y. H.; Guo, A. Q.; Guo, L. B.; Guo, Y. P.; Han, Y. L.; Hao, X. Q.; Harris, F. A.; He, K. L.; He, M.; He, Z. Y.; Held, T.; Heng, Y. K.; Hou, Z. L.; Hu, H. M.; Hu, J. F.; Hu, T.; Huang, B.; Huang, G. M.; Huang, J. S.; Huang, X. T.; Huang, Y. P.; Hussain, T.; Ji, C. S.; Ji, Q.; Ji, X. B.; Ji, X. L.; Jia, L. K.; Jiang, L. L.; Jiang, X. S.; Jiao, J. B.; Jiao, Z.; Jin, D. P.; Jin, S.; Jing, F. F.; Kalantar-Nayestanaki, N.; Kavatsyuk, M.; Kuehn, W.; Lai, W.; Lange, J. S.; Leung, J. K. C.; Li, C. H.; Li, Cheng; Li, Cui; Li, D. M.; Li, F.; Li, G.; Li, H. B.; Li, J. C.; Li, K.; Li, Lei; Li, N. B.; Li, Q. J.; Li, S. L.; Li, W. D.; Li, W. G.; Li, X. L.; Li, X. N.; Li, X. Q.; Li, X. R.; Li, Z. B.; Liang, H.; Liang, Y. F.; Liang, Y. T.; Liao, G. R.; Liao, X. T.; Liu, B. J.; Liu, B. J.; Liu, C. L.; Liu, C. X.; Liu, C. Y.; Liu, F. H.; Liu, Fang; Liu, Feng; Liu, H.; Liu, H. B.; Liu, H. H.; Liu, H. M.; Liu, H. W.; Liu, J. P.; Liu, K. Y.; Liu, Kai; Liu, Kun; Liu, P. L.; Liu, S. B.; Liu, X.; Liu, X. H.; Liu, Y.; Liu, Y. B.; Liu, Z. A.; Liu, Zhiqiang; Liu, Zhiqing; Loehner, H.; Lu, G. R.; Lu, H. J.; Lu, J. G.; Lu, Q. W.; Lu, X. R.; Lu, Y. P.; Luo, C. L.; Luo, M. X.; Luo, T.; Luo, X. L.; Lv, M.; Ma, C. L.; Ma, F. C.; Ma, H. L.; Ma, Q. M.; Ma, S.; Ma, T.; Ma, X. Y.; Ma, Y.; Maas, F. E.; Maggiora, M.; Malik, Q. A.; Mao, H.; Mao, Y. J.; Mao, Z. P.; Messchendorp, J. G.; Min, J.; Min, T. J.; Mitchell, R. E.; Mo, X. H.; Morales, C. Morales; Motzko, C.; Muchnoi, N. Yu.; Nefedov, Y.; Nicholson, C.; Nikolaev, I. B.; Ning, Z.; Olsen, S. L.; Ouyang, Q.; Pacetti, S.; Park, J. W.; Pelizaeus, M.; Peters, K.; Ping, J. L.; Ping, R. G.; Poling, R.; Prencipe, E.; Pun, C. S. J.; Qi, M.; Qian, S.; Qiao, C. F.; Qin, X. S.; Qin, Y.; Qin, Z. H.; Qiu, J. F.; Rashid, K. H.; Rong, G.; Ruan, X. D.; Sarantsev, A.; Schulze, J.; Shao, M.; Shen, C. P.; Shen, X. Y.; Sheng, H. Y.; Shepherd, M. R.; Song, X. Y.; Spataro, S.; Spruck, B.; Sun, D. H.; Sun, G. X.; Sun, J. F.; Sun, S. S.; Sun, X. D.; Sun, Y. J.; Sun, Y. Z.; Sun, Z. J.; Sun, Z. T.; Tang, C. J.; Tang, X.; Thorndike, E. H.; Tian, H. L.; Toth, D.; Ullrich, M.; Varner, G. S.; Wang, B.; Wang, B. Q.; Wang, K.; Wang, L. L.; Wang, L. S.; Wang, M.; Wang, P.; Wang, P. L.; Wang, Q.; Wang, Q. J.; Wang, S. G.; Wang, X. F.; Wang, X. L.; Wang, Y. D.; Wang, Y. F.; Wang, Y. Q.; Wang, Z.; Wang, Z. G.; Wang, Z. Y.; Wei, D. H.; Weidenkaff, P.; Wen, Q. G.; Wen, S. P.; Werner, M.; Wiedner, U.; Wu, L. H.; Wu, N.; Wu, S. X.; Wu, W.; Wu, Z.; Xia, L. G.; Xiao, Z. J.; Xie, Y. G.; Xiu, Q. L.; Xu, G. F.; Xu, G. M.; Xu, H.; Xu, Q. J.; Xu, X. P.; Xu, Y.; Xu, Z. R.; Xue, F.; Xue, Z.; Yan, L.; Yan, W. B.; Yan, Y. H.; Yang, H. X.; Yang, T.; Yang, Y.; Yang, Y. X.; Ye, H.; Ye, M.; Ye, M. H.; Yu, B. X.; Yu, C. X.; Yu, J. S.; Yu, S. P.; Yuan, C. Z.; Yuan, W. L.; Yuan, Y.; Zafar, A. A.; Zallo, A.; Zeng, Y.; Zhang, B. X.; Zhang, B. Y.; Zhang, C. C.; Zhang, D. H.; Zhang, H. H.; Zhang, H. Y.; Zhang, J.; Zhang, J. G.; Zhang, J. Q.; Zhang, J. W.; Zhang, J. Y.; Zhang, J. Z.; Zhang, L.; Zhang, S. H.; Zhang, T. R.; Zhang, X. J.; Zhang, X. Y.; Zhang, Y.; Zhang, Y. H.; Zhang, Y. S.; Zhang, Z. P.; Zhang, Z. Y.; Zhao, G.; Zhao, H. S.; Zhao, J. W.; Zhao, K. X.; Zhao, Lei; Zhao, Ling; Zhao, M. G.; Zhao, Q.; Zhao, S. J.; Zhao, T. C.; Zhao, X. H.; Zhao, Y. B.; Zhao, Z. G.; Zhemchugov, A.; Zheng, B.; Zheng, J. P.; Zheng, Y. H.; Zheng, Z. P.; Zhong, B.; Zhong, J.; Zhou, L.; Zhou, X. K.; Zhou, X. R.; Zhu, C.; Zhu, K.; Zhu, K. J.; Zhu, S. H.; Zhu, X. L.; Zhu, X. W.; Zhu, Y. M.; Zhu, Y. S.; Zhu, Z. A.; Zhuang, J.; Zou, B. S.; Zou, J. H.; Zuo, J. X.

    2012-01-01

    The decays J/psi -> p (p) over bar and J/psi -> n (n) over bar have been investigated with a sample of 225.2 x 10(6) J/psi events collected with the BESIII detector at the BEPCII e(+)e(-) collider. The branching fractions are determined to be B(J/psi -> p (p) over bar) = (2.112 +/- 0.004 +/- 0.031 x

  8. Nonbinary quantum codes

    CERN Document Server

    Rains, E M

    1997-01-01

    We present several results on quantum codes over general alphabets (that is, in which the fundamental units may have more than 2 states). In particular, we consider codes derived from finite symplectic geometry assumed to have additional global symmetries. From this standpoint, the analogues of Calderbank-Shor-Steane codes and of GF(4)-linear codes turn out to be special cases of the same construction. This allows us to construct families of quantum codes from certain codes over number fields; in particular, we get analogues of quadratic residue codes, including a single-error correcting code encoding one letter in five, for any alphabet size. We also consider the problem of fault-tolerant computation through such codes, generalizing ideas of Gottesman.

  9. Method for non-destructive measurement of heat affected zone of identification code on nuclear fuel rod

    International Nuclear Information System (INIS)

    In a method for the nondestructive measurement of the depth of the heat affected zone underneath a laser generated identification code on a nuclear fuel rod tube, the change in impedance of an electromagnetic foil produced by a portion of the tube is measured before and after the etching of a bar code is performed by use of laser power. The impedance change in the coil produced by the bar code-bearing tube portion is compared with the impedance change produced in the coil by the same tube portion before the bar code is generated thereon to determine whether a maximum allowed depth of the heat affected zone of the tube portion has been exceeded. (author)

  10. Towards Multi Label Text Classification through Label Propagation

    Directory of Open Access Journals (Sweden)

    Shweta C. Dharmadhikari

    2012-06-01

    Full Text Available Classifying text data has been an active area of research for a long time. Text document is multifaceted object and often inherently ambiguous by nature. Multi-label learning deals with such ambiguous object. Classification of such ambiguous text objects often makes task of classifier difficult while assigning relevant classes to input document. Traditional single label and multi class text classification paradigms cannot efficiently classify such multifaceted text corpus. Through our paper we are proposing a novel label propagation approach based on semi supervised learning for Multi Label Text Classification. Our proposed approach models the relationship between class labels and also effectively represents input text documents. We are using semi supervised learning technique for effective utilization of labeled and unlabeled data for classification. Our proposed approach promises better classification accuracy and handling of complexity and elaborated on the basis of standard datasets such as Enron, Slashdot and Bibtex.

  11. Instance-Aware Hashing for Multi-Label Image Retrieval.

    Science.gov (United States)

    Lai, Hanjiang; Yan, Pan; Shu, Xiangbo; Wei, Yunchao; Yan, Shuicheng

    2016-06-01

    Similarity-preserving hashing is a commonly used method for nearest neighbor search in large-scale image retrieval. For image retrieval, deep-network-based hashing methods are appealing, since they can simultaneously learn effective image representations and compact hash codes. This paper focuses on deep-network-based hashing for multi-label images, each of which may contain objects of multiple categories. In most existing hashing methods, each image is represented by one piece of hash code, which is referred to as semantic hashing. This setting may be suboptimal for multi-label image retrieval. To solve this problem, we propose a deep architecture that learns instance-aware image representations for multi-label image data, which are organized in multiple groups, with each group containing the features for one category. The instance-aware representations not only bring advantages to semantic hashing but also can be used in category-aware hashing, in which an image is represented by multiple pieces of hash codes and each piece of code corresponds to a category. Extensive evaluations conducted on several benchmark data sets demonstrate that for both the semantic hashing and the category-aware hashing, the proposed method shows substantial improvement over the state-of-the-art supervised and unsupervised hashing methods. PMID:27019492

  12. Instance-Aware Hashing for Multi-Label Image Retrieval.

    Science.gov (United States)

    Lai, Hanjiang; Yan, Pan; Shu, Xiangbo; Wei, Yunchao; Yan, Shuicheng

    2016-06-01

    Similarity-preserving hashing is a commonly used method for nearest neighbor search in large-scale image retrieval. For image retrieval, deep-network-based hashing methods are appealing, since they can simultaneously learn effective image representations and compact hash codes. This paper focuses on deep-network-based hashing for multi-label images, each of which may contain objects of multiple categories. In most existing hashing methods, each image is represented by one piece of hash code, which is referred to as semantic hashing. This setting may be suboptimal for multi-label image retrieval. To solve this problem, we propose a deep architecture that learns instance-aware image representations for multi-label image data, which are organized in multiple groups, with each group containing the features for one category. The instance-aware representations not only bring advantages to semantic hashing but also can be used in category-aware hashing, in which an image is represented by multiple pieces of hash codes and each piece of code corresponds to a category. Extensive evaluations conducted on several benchmark data sets demonstrate that for both the semantic hashing and the category-aware hashing, the proposed method shows substantial improvement over the state-of-the-art supervised and unsupervised hashing methods.

  13. Studies of $\\gamma\\gamma\\to\\Lambda\\bar{\\Lambda},\\Sigma^0\\bar{\\Sigma^0}$ production at Belle

    CERN Document Server

    Kuo, C C; Adachi, I; Aihara, H; Anipko, D; Aoki, K; Arakawa, T; Arinstein, K; Asano, Y; Aso, T; Aulchenko, V M; Aushev, T; Aziz, T; Bahinipati, S; Bakich, A M; Balagura, V; Ban, Y; Banerjee, S; Barberio, E; Barbero, M; Bay, A; Bedny, I; Belous, K S; Bitenc, U; Bizjak, I; Blyth, S; Bondar, A; Bozek, A; Bracko, M; Brodzicka, J; Browder, T E; Chang, M C; Chang, P; Chao, Y; Chen, A; Chen, K F; Chen, W T; Cheon, B G; Chistov, R; Choi, J H; Choi, S K; Choi, Y; Choi, Y K; Chuvikov, A; Cole, S; Dalseno, J; Danilov, M; Dash, M; Dowd, R; Dragic, J; Drutskoy, A; Eidelman, S; Enari, Y; Epifanov, D A; Fratina, S; Fujii, H; Fujikawa, M; Gabyshev, N; Garmash, A; Gershon, T; Go, A; Gokhroo, G; Goldenzweig, P; Golob, B; Gorisek, A; Grosse-Perdekamp, M; Guler, H; Ha, H; Haba, J; Hara, K; Hara, T; Hasegawa, Y; Hastings, N C; Hayasaka, K; Hayashii, H; Hazumi, M; Heffernan, D; Higuchi, T; Hinz, L; Hokuue, T; Hoshi, Y; Hoshina, K; Hou, S; Hou, W S; Hsiung, Y B; Igarashi, Y; Iijima, T; Ikado, K; Imoto, A; Inami, K; Ishikawa, A; Ishino, H; Itoh, K; Itoh, R; Iwabuchi, M; Iwasaki, M; Iwasaki, Y; Jacoby, C; Jones, M; Kakuno, H; Kang, J H; Kang, J S; Kapusta, P; Kataoka, S U; Katayama, N; Kawai, H; Kawasaki, T; Khan, H R; Kibayashi, A; Kichimi, H; Kikuchi, N; Kim, H J; Kim, H O; Kim, J H; Kim, S K; Kim, T H; Kim, Y J; Kinoshita, K; Kishimoto, N; Korpar, S; Kozakai, Y; Krizan, P; Krokovnyi, P P; Kubota, T; Kulasiri, R; Kumar, R; Kuo, C C; Kurihara, E; Kusaka, A; Kuzmin, A; Kwon, Y J; Lange, J S; Leder, G; Lee, J; Lee, S E; Lee, Y J; Lesiak, T; Li, J; Limosani, A; Lin, C Y; Lin, S W; Liu, Y; Liventsev, D; MacNaughton, J; Majumder, G; Mandl, F; Marlow, D; Matsumoto, T; Matyja, A; McOnie, S; Medvedeva, T; Mikami, Y; Mitaroff, W A; Miyabayashi, K; Miyake, H; Miyata, H; Miyazaki, Y; Mizuk, R; Mohapatra, D; Moloney, G R; Mori, T; Müller, J; Murakami, A; Nagamine, T; Nagasaka, Y; Nakagawa, T; Nakahama, Y; Nakamura, I; Nakano, E; Nakao, M; Nakazawa, H; Natkaniec, Z; Neichi, K; Nishida, S; Nishimura, K; Nitoh, O; Noguchi, S; Nozaki, T; Ogawa, A; Ogawa, S; Ohshima, T; Okabe, T; Okuno, S; Olsen, S L; Ono, S; Ostrowicz, W; Ozaki, H; Pakhlov, P; Pakhlova, G; Palka, H; Park, C W; Park, H; Park, K S; Parslow, N; Peak, L S; Pernicka, M; Pestotnik, R; Peters, M; Piilonen, L E; Poluektov, A; Ronga, F J; Root, N; Rorie, J; Rózanska, M; Sahoo, H; Saitoh, S; Sakai, Y; Sakamoto, H; Sakaue, H; Sarangi, T R; Sato, N; Satoyama, N; Sayeed, K; Schietinger, T; Schneider, O; Schonmeier, P; Schümann, J; Schwanda, C; Schwartz, A J; Seidl, R; Seki, T; Senyo, K; Sevior, M E; Shapkin, M; Shen, Y T; Shibuya, H; Shwartz, B; Sidorov, V; Singh, J B; Sokolov, A; Somov, A; Soni, N; Stamen, R; Stanic, S; Staric, M; Stöck, H; Sugiyama, A; Sumisawa, K; Sumiyoshi, T; Suzuki, S; Suzuki, S Y; Tajima, O; Takada, N; Takasaki, F; Tamai, K; Tamura, N; Tanabe, K; Tanaka, M; Taylor, G N; Teramoto, Y; Tian, X C; Tikhomirov, I; Trabelsi, K; Tsai, Y T; Tse, Y F; Tsuboyama, T; Tsukamoto, T; Uchida, K; Uchida, Y; Uehara, S; Uglov, T; Ueno, K; Unno, Y; Uno, S; Urquijo, P; Ushiroda, Y; Usov, Yu; Varner, G; Varvell, K E; Villa, S; Wang, C C; Wang, C H; Wang, M Z; Watanabe, M; Watanabe, Y; Wicht, J; Widhalm, L; Wiechczynski, J; Won, E; Wu, C H; Xie, Q L; Yabsley, B D; Yamaguchi, A; Yamamoto, H; Yamamoto, S; Yamashita, Y; Yamauchi, M; Heyoung Yang; Yoshino, S; Yuan, Y; Yusa, Y; Zang, S L; Zhang, C C; Zhang, J; Zhang, L M; Zhang, Z P; Zhilich, V; Ziegler, T; Zupanc, A; Zürcher, D; al., et

    2006-01-01

    Cross sections for hyperon pair production from two-photon collisions, $\\gamma\\gamma\\to\\Lambda\\bar{\\Lambda},\\Sigma^0\\bar{\\Sigma^0}$, are measured in the 2-4 GeV energy region at Belle, using 464 fb$^{-1}$ of data. A contribution from the intermediate resonance $\\eta_c(1S)$ is observed, and the products of the two-photon width of the $\\eta_c(1S)$ and its branching ratios to $\\Lambda\\bar{\\Lambda}$ and $\\Sigma^0\\bar{\\Sigma^0}$ are measured. The results will help test QCD models.

  14. Investigation of the $X(5568)$ as a fully open-flavor $su\\bar b\\bar d$ tetraquark state

    CERN Document Server

    Chen, Wei; Liu, Xiang; Steele, T G; Zhu, Shi-Lin

    2016-01-01

    We investigate the newly observed charged $X(5568)$ meson as an exotic open-flavor tetraquark state $su\\bar b\\bar d$ with $J^P=0^+/1^+$ in the framework of QCD sum rules. We use the color antisymmetric $[\\mathbf{\\bar 3_c}]_{su} \\otimes [\\mathbf{3_c}]_{\\bar{b}\\bar d}$ tetraquark currents in both scalar and axial-vector channels to perform evaluations and numerical analyses. Our results imply that the $X(5568)$ can be interpreted as both the scalar $su\\bar b\\bar d$ tetraquark state and the axial-vector one, which are in good agreement with the experiment observation. We also investigate the possible decay patterns of the $X(5568)$ and suggest to search for its neutral partner in the radiative decay into $B_s^0 \\gamma$ and $B_s^* \\gamma$, which can be used to determine its spin-parity quantum numbers. Moreover, we predict its charmed partner state around $2.55$ GeV with the quark content $su\\bar c\\bar d$ and $J^P=0^+/1^+$.

  15. Nutritional Evaluation of NASA's Rodent Food Bar Diet

    Science.gov (United States)

    Barrett, Joyce E.; Yu, Diane S.; Dalton, Bonnie P.

    2000-01-01

    Tests are being conducted on NASA's rodent Food Bar in preparation for long-term use as the rat and mouse diet aboard the International Space Station. Nutritional analyses are performed after the bars are manufactured and then repeated periodically to determine nutritional stability. The primary factors analyzed are protein, ash, fat, fiber, moisture, amino acids, fatty acids, and minerals. Nutrient levels are compared to values published in the National Research Council's dietary requirements for rodents, and also to those contained in several commonly used commercial rodent lab diets. The Food Bar is manufactured from a powdered diet to which moisture is added as it is processed through an extruder. The bars are dipped into potassium sorbate, vacuum-sealed, and irradiated. In order to determine nutrient changes during extrusion and irradiation, the powdered diet, the non-irradiated bars, and the irradiated bars are all analyzed. We have observed lower values for some nutrients (iodine, vitamin K, and iron) in the Food Bars compared with NRC requirements. Many nutrients in the Food Bars are contained at a higher level than levels in the NRC requirements. An additional factor we are investigating is the 26% moisture level in the Food Bars, which drops to about 15% within a week, compared to a stable 10% moisture in many standard lab chow diets. In addition to the nutritional analyses, the food bar is being fed to several strains of rats and mice, and feeding study and necropsy results are being observed (Barrett et al, unpublished data). Information from the nutritional analyses and from the rodent studies will enable us to recommend the formulation that will most adequately meet the rodent Food Bar requirements for long-term use aboard the Space Station.

  16. INFLUENCING OF FRICTION IN HINGES FORCE SIZE OF BARS

    Directory of Open Access Journals (Sweden)

    BOHOMAZ V. N.

    2016-04-01

    Full Text Available Formulation of the problem. The size of critical force of bar on the traditional method of calculation is determined in supposition of ideal hinge in the place of fixing of bar. There are both a hinge resistance at the turn of bar ends and their moving in the real hinges. Thus, there is the necessity of influencing character determination of these hinge imperfections on the size of critical force. In the existent scientific labours is devoted the alike problems, influencing of friction in the hinges of bar fastening on the size of critical force was not taken into account. At determination of bars stability with no ideality of hinges friction in them it is possible to take into account by the eccentric appendix of loading or appendix of moment. However at such approach it is difficult enough to define the size of attached force or moment. Purpose. To set influencing of friction in the hinge of bar fastening on of his critical force size in sense of Euler, and also build dependences for determination of bar critical force taking into account mechanical descriptions of hinges materials. Conclusion. For the task of determination the size of bar critical force with the joint fastening on ends are got the dependences which take into account mechanical descriptions of material hinge. The received dependences allow to define more exact meaning of critical force for bars. The examples of calculation of whole bar and bar with undercuting in the middle are resulted that values of critical force, certain on a traditional method are overpriced.

  17. Business ethics in the textile, clothing and footwear (tcf) industries : codes of conduct.

    OpenAIRE

    Sajhau, Jean-Paul

    1997-01-01

    Discusses the adoption and implementation of ethical codes in the textile, clothing and footwear industries. Looks at the role of non- governmental organizations in the promotion of codes of conduct (e.g. labelling campaigns), the components of a standard code of conduct and the provisions of the codes of conduct of Levi Strauss, Sara Lee, Phillips-van Heusen, The Gap, Nike, Reebok and some major retail networks.

  18. Polyphase alternating codes

    OpenAIRE

    M. Markkanen; Vierinen, J.; Markkanen, J.

    2007-01-01

    We present a new class of alternating codes. Instead of the customary binary phase codes, the new codes utilize either p or p–1 phases, where p is a prime number. The first class of codes has code length pm, where m is a positive integer, the second class has code length p–1. We give an actual construction algorithm, and explain the principles behind it. We ...

  19. Label and Label-Free Detection Techniques for Protein Microarrays

    Directory of Open Access Journals (Sweden)

    Amir Syahir

    2015-04-01

    Full Text Available Protein microarray technology has gone through numerous innovative developments in recent decades. In this review, we focus on the development of protein detection methods embedded in the technology. Early microarrays utilized useful chromophores and versatile biochemical techniques dominated by high-throughput illumination. Recently, the realization of label-free techniques has been greatly advanced by the combination of knowledge in material sciences, computational design and nanofabrication. These rapidly advancing techniques aim to provide data without the intervention of label molecules. Here, we present a brief overview of this remarkable innovation from the perspectives of label and label-free techniques in transducing nano‑biological events.

  20. Bars and spheroids in gravimetry problem

    CERN Document Server

    Sizikov, Valery

    2016-01-01

    The direct gravimetry problem is solved by dividing each deposit body into a set of vertical adjoining bars, whereas in the inverse problem, each deposit body is modelled by a homogeneous ellipsoid of revolution (spheroid). Well-known formulae for the z-component of gravitational intensity for a spheroid are transformed to a convenient form. Parameters of a spheroid are determined by minimizing the Tikhonov smoothing functional with constraints on the parameters, which makes the ill-posed inverse problem by unique and stable. The Bulakh algorithm for initial estimating the depth and mass of a deposit is modified. The proposed technique is illustrated by numerical model examples of deposits in the form of two and five bodies. The inverse gravimetry problem is interpreted as a gravitational tomography problem or, in other words, as "introscopy" of Earth's crust and mantle.

  1. Bus bar electrical feedthrough for electrorefiner system

    Science.gov (United States)

    Williamson, Mark; Wiedmeyer, Stanley G; Willit, James L; Barnes, Laurel A; Blaskovitz, Robert J

    2013-12-03

    A bus bar electrical feedthrough for an electrorefiner system may include a retaining plate, electrical isolator, and/or contact block. The retaining plate may include a central opening. The electrical isolator may include a top portion, a base portion, and a slot extending through the top and base portions. The top portion of the electrical isolator may be configured to extend through the central opening of the retaining plate. The contact block may include an upper section, a lower section, and a ridge separating the upper and lower sections. The upper section of the contact block may be configured to extend through the slot of the electrical isolator and the central opening of the retaining plate. Accordingly, relatively high electrical currents may be transferred into a glovebox or hot-cell facility at a relatively low cost and higher amperage capacity without sacrificing atmosphere integrity.

  2. A Distinct Structure inside the Galactic Bar

    Science.gov (United States)

    Nishiyama, Shogo; Nagata, Tetsuya; Baba, Daisuke; Haba, Yasuaki; Kadowaki, Ryota; Kato, Daisuke; Kurita, Mikio; Nagashima, Chie; Nagayama, Takahiro; Murai, Yuka; Nakajima, Yasushi; Tamura, Motohide; Nakaya, Hidehiko; Sugitani, Koji; Naoi, Takahiro; Matsunaga, Noriyuki; Tanabé, Toshihiko; Kusakabe, Nobuhiko; Sato, Shuji

    2005-03-01

    We present the result of a near-infrared (JHKs) survey along the Galactic plane, -10.5dSIRIUS camera. Ks versus H-Ks color-magnitude diagrams reveal a well-defined population of red clump stars whose apparent magnitude peak changes continuously along the Galactic plane, from Ks=13.4 at l=-10deg to Ks=12.2 at l=10deg after dereddening. This variation can be explained by the barlike structure found in previous studies, but we find an additional inner structure at |l|<~4deg, where the longitude-apparent magnitude relation is distinct from the outer bar and where the apparent magnitude peak changes by only ~0.1 mag over the central 8°. The exact nature of this inner structure is as yet uncertain.

  3. Predicting Vertical Jump Height from Bar Velocity

    Directory of Open Access Journals (Sweden)

    Amador García-Ramos, Igor Štirn, Paulino Padial, Javier Argüelles-Cienfuegos, Blanca De la Fuente, Vojko Strojnik, Belén Feriche

    2015-06-01

    Full Text Available The objective of the study was to assess the use of maximum (Vmax and final propulsive phase (FPV bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s-2. Vertical jump height was calculated from the take-off velocity (Vtake-off provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384 was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504 was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r2 = 0.307, while the differences between Vmax and Vtake-off were homogenously distributed (r2 = 0.071. These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine.

  4. Depth Of Modulation And Spot Size Selection In Bar-Code Laser Scanners

    Science.gov (United States)

    Barkan, Eric; Swartz, Jerome

    1982-04-01

    Many optical and electronic considerations enter into the selection of optical spot size in flying spot laser scanners of the type used in modern industrial and commerical environments. These include: the scale of the symbols to be read, optical background noise present in the symbol substrate, and factors relating to the characteristics of the signal processor. Many 'front ends' consist of a linear signal conditioner followed by nonlinear conditioning and digitizing circuitry. Although the nonlinear portions of the circuit can be difficult to characterize mathematically, it is frequently possible to at least give a minimum depth of modulation measure to yield a worst-case guarantee of adequate performance with respect to digitization accuracy. Depth of modulation actually delivered to the nonlinear circuitry will depend on scale, contrast, and noise content of the scanned symbol, as well as the characteristics of the linear conditioning circuitry (eg. transfer function and electronic noise). Time and frequency domain techniques are applied in order to estimate the effects of these factors in selecting a spot size for a given system environment. Results obtained include estimates of the effects of the linear front end transfer function on effective spot size and asymmetries which can affect digitization accuracy. Plots of convolution-computed modulation patterns and other important system properties are presented. Considerations are limited primarily to Gaussian spot profiles but also apply to more general cases. Attention is paid to realistic symbol models and to implications with respect to printing tolerances.

  5. A Bar Code and Radio-Frequency Identification System for Transfusion Safety

    Institute of Scientific and Technical Information of China (English)

    Sandler SG; DiBandi L; Langeberg A; Gibble J; Wilson C; Feldman CF

    2006-01-01

    This presentation will describe a pilot study of radio-frequency (RF) identification tags ("chips") that was conducted in parallel with standard procedures for the collection and testing of Red Blood Cells (Greater Chesapeake and Potomac Region, American Red Cross Biomedical Services, Baltimore, MD) and transfusion (Georgetown University Hospital, Washington, DC). The purpose of the study was to evaluate whether multi-write RF chips could be attached to blood bags, programmed, and used to facilitate the collection of information from (1) a blood bag manufacturer to (2) a blood collection center and, subsequently, to (3) a hospital transfusion service.

  6. Bar Code-Based Management to Enhance Efficiency of a Sterile Supply Unit in Singapore.

    Science.gov (United States)

    Goh, Meh Meh; Tan, Agnes B H; Leong, Mike H W

    2016-04-01

    Sterile surgical instruments are essential for successful surgical outcomes. The Singapore General Hospital's Theatre Sterile Supplies Unit (TSSU) has faced many challenges, including increasing demand for instruments and the need to maintain instruments of greater complexity. To address these challenges, stakeholders from key departments at Singapore General Hospital formed a multidisciplinary team to transform operations in the TSSU. The team adopted and implemented the TSSU Instrument Management System (TIMS) in three phases over five years. The project included standardizing instrument-naming conventions, implementing electronic integration of instrument tracking in the unit, extending traceability of instruments to the major ORs, initiating integrated web-based instrument ordering, and extending the system management of instruments at ambulatory surgery and specialized OR facilities. The implementation of TIMS has improved inventory, supply, and quality management; reduced instrument repairs; and led to savings through increased productivity and lower expenses. PMID:27004503

  7. Coupling scanning electronc microscopy with DNA bar coding: A novel approach for thrips identification

    Science.gov (United States)

    The small size and cryptic nature of thrips pests help them acquire microhabitats of a plant and in the field, often making their monitoring and the identification process difficult. Accurate identification of such pests is a fundamental requirement in development of any effective quarantine and man...

  8. Network coding for computing: Linear codes

    CERN Document Server

    Appuswamy, Rathinakumar; Karamchandani, Nikhil; Zeger, Kenneth

    2011-01-01

    In network coding it is known that linear codes are sufficient to achieve the coding capacity in multicast networks and that they are not sufficient in general to achieve the coding capacity in non-multicast networks. In network computing, Rai, Dey, and Shenvi have recently shown that linear codes are not sufficient in general for solvability of multi-receiver networks with scalar linear target functions. We study single receiver networks where the receiver node demands a target function of the source messages. We show that linear codes may provide a computing capacity advantage over routing only when the receiver demands a `linearly-reducible' target function. % Many known target functions including the arithmetic sum, minimum, and maximum are not linearly-reducible. Thus, the use of non-linear codes is essential in order to obtain a computing capacity advantage over routing if the receiver demands a target function that is not linearly-reducible. We also show that if a target function is linearly-reducible,...

  9. Edge colouring by total labellings

    DEFF Research Database (Denmark)

    Brandt, Stephan; Rautenbach, D.; Stiebitz, M.;

    2010-01-01

    We introduce the concept of an edge-colouring total k-labelling. This is a labelling of the vertices and the edges of a graph G with labels 1, 2, ..., k such that the weights of the edges define a proper edge colouring of G. Here the weight of an edge is the sum of its label and the labels of its...... two endvertices. We define χ (G) to be the smallest integer k for which G has an edge-colouring total k-labelling. This parameter has natural upper and lower bounds in terms of the maximum degree Δ of G : ⌈ (Δ + 1) / 2 ⌉ ≤ χ (G) ≤ Δ + 1. We improve the upper bound by 1 for every graph and prove χ (G...

  10. A Better Carbon Footprint Label

    DEFF Research Database (Denmark)

    Thøgersen, John; Nielsen, Kristian S.

    2016-01-01

    Based on insights from behavioral economics, it is suggested to extend carbon footprint labeling with information about relative performance, using the well-known “traffic light” color scheme to communicate relative performance. To test this proposition, the impact of a carbon footprint label......, participants saw the original Carbon Trust label and in the other condition they saw the same label, but with traffic light colors added to communicate the product's relative performance in terms of carbon footprint. All included attributes were found to have a significant impact on consumer choices...... to indicate relative carbon footprint significantly increases carbon label effectiveness. Hence, a carbon footprint label is more effective if it uses traffic light colors to communicate the product's relative performance....

  11. Modeling the effects of labeling

    DEFF Research Database (Denmark)

    Juhl, Hans Jørn; Fjord, Thomas Ahle; Poulsen, Carsten Stig

    A new approach to evaluate the consequences of labeling is presented and applied to test the potential effect of a label on fresh fish. Labeling effects on quality perceptions and overall quality are studied. The empirical study is based on an experimental design and nearly 500 respondents partic...... participated in an in home test. The results indicate that catch time alone is not enough to work as an efficient predictor of actual perceived quality.......A new approach to evaluate the consequences of labeling is presented and applied to test the potential effect of a label on fresh fish. Labeling effects on quality perceptions and overall quality are studied. The empirical study is based on an experimental design and nearly 500 respondents...

  12. New Observables In the Decay Mode \\bar B_d \\-->\\bar K^{0*} \\ell^+ \\ell^-

    Energy Technology Data Exchange (ETDEWEB)

    Egede, U.; /Imperial Coll., London; Hurth, T.; /CERN /SLAC; Matias, J.; Ramon, M.; /Barcelona, IFAE; Reece, W.; /Imperial Coll., London

    2008-08-07

    We discuss the large set of observables available from the angular distributions of the decay {bar B}{sub d} {yields} {bar K}*{sup 0}{ell}{sup +}{ell}{sup -}. We present a NLO analysis of all observables based on the QCD factorization approach in the low-dilepton mass region and an estimate of {Lambda}/m{sub b} corrections. Moreover, we discuss their sensitivity to new physics. We explore the experimental sensitivities at LHCb (10 fb{sup -1}) and SuperLHCb (100 fb{sup -1}) based on a full-angular fit method and explore the sensitivity to right handed currents. We also show that the previously discussed transversity amplitude A{sub T}{sup (1)} cannot be measured at the LHCb experiment or at future B factory experiments as it requires a measurement of the spin of the final state particles.

  13. Mothers' labeling responses to infants' gestures predict vocabulary outcomes.

    Science.gov (United States)

    Olson, Janet; Masur, Elise Frank

    2015-11-01

    Twenty-nine infants aged 1;1 and their mothers were videotaped while interacting with toys for 18 minutes. Six experimental stimuli were presented to elicit infant communicative bids in two communicative intent contexts - proto-declarative and proto-imperative. Mothers' verbal responses to infants' gestural and non-gestural communicative bids were coded for object and action labels. Relations between maternal labeling responses and infants' vocabularies at 1;1 and 1;5 were examined. Mothers' labeling responses to infants' gestural communicative bids were concurrently and predictively related to infants' vocabularies, whereas responses to non-gestural communicative bids were not. Mothers' object labeling following gestures in the proto-declarative context mediated the association from infants' gesturing in the proto-declarative context to concurrent noun lexicons and was the strongest predictor of subsequent noun lexicons. Mothers' action labeling after infants' gestural bids in the proto-imperative context predicted infants' acquisition of action words at 1;5. Findings show that mothers' responsive labeling explain specific relations between infants' gestures and their vocabulary development. PMID:25643656

  14. Energy Drinks and Food Bars: Power or Hype?

    Science.gov (United States)

    ... How Can I Help a Friend Who Cuts? Energy Drinks and Food Bars: Power or Hype? KidsHealth > ... nutritivas: ¿Energía o mera exageración? The Buzz on Energy Foods Energy drinks and nutrition bars often make ...

  15. Barred galaxies in the EAGLE cosmological hydrodynamical simulation

    CERN Document Server

    Algorry, David G; Abadi, Mario G; Sales, Laura V; Bower, Richard G; Crain, Robert A; Vecchia, Claudio Dalla; Frenk, Carlos S; Schaller, Matthieu; Schaye, Joop; Theuns, Tom

    2016-01-01

    We examine the properties of barred disc galaxies in a LCDM cosmological hydrodynamical simulation from the EAGLE project. Our study follows the formation of 269 discs identified at z = 0 in the stellar mass range 10.6 < log Mstr /M < 11. These discs show a wide range of bar strengths, from unbarred discs to weak bars to strongly barred systems (= 20%). Bars in these systems develop after redshift = 1.3, on timescales that depend sen- sitively on the strength of the pattern. Strong bars develop relatively quickly (in a few Gyr, = 10 disc rotation periods) in systems that are disc dominated, gas poor, and have declining rotation curves. Weak bars develop more slowly in systems where the disc is less gravitation- ally important, and are still growing at z = 0. Unbarred galaxies are comparatively gas-rich discs whose rotation speeds do not exceed the maximum circular velocity of the halos they inhabit. Bar lengths compare favourably with observations, ranging from 0.2 to 0.8 times the radius containing 90%...

  16. Mechanical Properties of Welded Deformed Reinforcing Steel Bars

    Directory of Open Access Journals (Sweden)

    Ghafur H. Ahmed

    2015-05-01

    Full Text Available Reinforcement strength, ductility and bendability properties are important components in design of reinforced concrete members, as the strength of any member comes mainly from reinforcement. Strain compatibility and plastic behaviors are mainly depending on reinforcement ductility. In construction practice, often welding of the bars is required. Welding of reinforcement is an instant solution in many cases, whereas welding is not a routine connection process. Welding will cause deficiencies in reinforcement bars, metallurgical changes and re-crystallization of microstructure of particles. Weld metal toughness is extremely sensitive to the welding heat input that decreases both of its strength and ductility. For determining the effects of welding in reinforcement properties, 48 specimens were tested with 5 different bar diameters, divided into six groups. Investigated parameters were: properties of un-welded bars; strength, ductility and density of weld metal; strength and ductility reduction due to heat input for bundled bars and transverse bars; welding effect on bars’ bending properties; behavior of different joint types; properties of three weld groove shapes also the locations and types of failures sections. Results show that, strength and elongation of the welded bars decreased by (10-40% and (30-60% respectively. Cold bending of welded bars and groove welds shall be prevented.

  17. Morphologies introduced by bistability in barred-spiral galactic potentials

    Science.gov (United States)

    Tsigaridi, L.; Patsis, P. A.

    2015-04-01

    We investigate the orbital dynamics of a barred-spiral model when the system is rotating slowly and corotation is located beyond the end of the spiral arms. In the characteristic of the central family of periodic orbits, we find a `bistable region'. In the response model, we observe a ring surrounding the bar and spiral arms starting tangential to the ring. This is a morphology resembling barred-spiral systems with inner rings. However, the dynamics associated with this structure in the case we study is different from that of a typical bar ending close to corotation. The ring of our model is round, or rather elongated perpendicular to the bar. It is associated with a folding (an `S'-shaped feature) of the characteristic of the central family, which is typical in bistable bifurcations. Along the `S' part of the characteristic, we have a change in the orientation of the periodic orbits from an x1-type to an x2-type morphology. The orbits populated in the response model change rather abruptly their orientation when reaching the lowest energy of the `S'. The spirals of the model follow a standard `precessing ellipses flow' and the orbits building them have energies beyond the `S' region. The bar is structured mainly by sticky orbits from regions around the stability islands of the central family. This leads to the appearance of X features in the bars on the galactic plane. Such a bar morphology appears in the unsharp-masked images of some moderately inclined galaxies.

  18. Calculation of error bars for laser damage observations

    Science.gov (United States)

    Arenberg, Jonathan W.

    2008-10-01

    The use of the error bar is a critical means of communicating the quality of individual data points and a processed result. Understanding the error bar for a processed measurement depends on the measurement technique being used and is the subject of many recent works, as such, the paper will confine its scope to the determination of the error bar on a single data point. Many investigators either ignore the error bar altogether or use a "one size error fits all" method, both of these approaches are poor procedure and misleading. It is the goal of this work to lift the veil of mysticism surrounding error bars for damage observations and make their description, calculation and use, easy and commonplace. This paper will rigorously derive the error bar size as a function of the experimental parameters and observed data and will concentrate on the dependent variable, the cumulative probability of damage. The paper will begin with a discussion of the error bar as a measure of data quality or reliability. The expression for the variance in the parameters is derived via standard methods and converted to a standard deviation. The concept of the coverage factor is introduced to scale the error bar to the desired confidence level, completing the derivation

  19. Theoretical approaches to low energy $\\bar{K}N$ interactions

    CERN Document Server

    Cieply, Ales

    2016-01-01

    We provide a direct comparison of modern theoretical approaches based on the SU(3) chiral dynamics and describing the low energy $\\bar{K}N$ data. The model predictions for the $\\bar{K}N$ amplitudes and pole content of the models are discussed.

  20. Construction of Codes for Network Coding

    CERN Document Server

    Elsenhans, Andreas-Stephan; Wassermann, Alfred

    2010-01-01

    Based on ideas of K\\"otter and Kschischang we use constant dimension subspaces as codewords in a network. We show a connection to the theory of q-analogues of a combinatorial designs, which has been studied in Braun, Kerber and Laue as a purely combinatorial object. For the construction of network codes we successfully modified methods (construction with prescribed automorphisms) originally developed for the q-analogues of a combinatorial designs. We then give a special case of that method which allows the construction of network codes with a very large ambient space and we also show how to decode such codes with a very small number of operations.

  1. Classification and Labelling for Biocides

    OpenAIRE

    Rubbiani, Maristella

    2015-01-01

    CLP and biocides The EU Regulation (EC) No 1272/2008 on Classification, Labelling and Packaging of Substances and Mixtures, the CLP-Regulation, entered into force on 20th January, 2009. Since 1st December, 2010 the classification, labelling and packaging of substances has to comply with this Regulation. For mixtures, the rules of this Regulation are mandatory from 1st June, 2015; this means that until this date classification, labelling and packaging could either be carried out according to D...

  2. Aggregating Labels in Crowdsourcing Data

    OpenAIRE

    Priisalu, Maria; Grey, Francois; Segal, Ben

    2015-01-01

    Project Specification Crowdsourcing is gaining popularity in academia with the launch of crowdsourcing platforms such as Crowdcrafting [Lombraña, 2015] and GeoTagX [UNOSAT, 2015]. There have been a number of proposed algorithms for the aggregation of true labels and a confusion matrix from crowdsourced labels for ordinal, nominal and binary labels. The work here consists of an implementation of the Dawid Skene [Dawid 1979] adaptation of the Expectation Maximization algorithm [D...

  3. TIPONLINE Code Table

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Coded items are entered in the tiponline data entry program. The codes and their explanations are necessary in order to use the data

  4. SEVERO code - user's manual

    International Nuclear Information System (INIS)

    This user's manual contains all the necessary information concerning the use of SEVERO code. This computer code is related to the statistics of extremes = extreme winds, extreme precipitation and flooding hazard risk analysis. (A.C.A.S.)

  5. GUIDELESS SPATIAL COORDINATE MEASUREMENT TECHNOLOGY BASED ON CODING POLE

    Institute of Scientific and Technical Information of China (English)

    ZHAO Min; QIU Zongming; QU Jiamin; LIU Hongzhao

    2008-01-01

    A new method of guideless spatial coordinate measurement technology based on coding pole and vision measurement is proposed. Unequal spacing of bar code is adopted to pole, so that the code combination of pole image in measuring field is unique. Holographic characteristics of numeric coding pole are adopted to obtain pole pose and pole probe position by any section of bar code on the pole. Spatial coordinates of measuring points can be obtained by coordinate transform. The contradiction between high resolution and large visual field of image sensor is resolved, thereby providing a new concept for surface shape measurement of large objects with high precision. The measurement principles of the system are expounded and mathematic model is established. The measurement equation is evaluated by simulation experiments and the measurement precision is analyzed. Theoretical analysis and simulation experiments prove that this system is characterized by simple structure and wide measurement range. Therefore it can be used in the 3-dimentional coordinate measurement of large objects.

  6. An observer's view of simulated galaxies: disc-to-total ratios, bars, and (pseudo-)bulges

    CERN Document Server

    Scannapieco, Cecilia; Jonsson, Patrik; White, Simon D M

    2010-01-01

    We use cosmological hydrodynamical simulations of the formation of Milky Way mass galaxies to study the relative importance of the main stellar components, discs, bulges, and bars, at z=0. The main aim of this work is to understand if estimates of the structural parameters of these components determined from kinematics (as usually done in simulations) agree well with those obtained using a photometric bulge/disc/bar decomposition (as done in observations). To perform such a comparison, we produced synthetic observations of the simulation outputs with the Monte-Carlo radiative transfer code SUNRISE and used the BUDDA code to make 2D photometric decompositions of the resulting images. We find that the kinematic disc-to-total ratio (D/T) estimates are systematically and significantly lower than the photometric ones. While the maximum D/T ratios obtained with the former method are of the order of 0.2, they are typically >0.4, and can be as high as 0.7, according to the latter. The photometric decomposition shows ...

  7. Bar slowdown and the distribution of dark matter in barred galaxies

    CERN Document Server

    Athanassoula, E

    2013-01-01

    `Conspiracy' between the dark and the baryonic mater prohibits an unambiguous decomposition of disc galaxy rotation curves into the corresponding components. Several methods have been proposed to counter this difficulty, but their results are widely discrepant. In this paper, I revisit one of these methods, which relies on the relation between the halo density and the decrease of the bar pattern speed. The latter is routinely characterised by the ratio ${\\cal R}$ of the corotation radius $R_{CR}$ to the bar length $L_b$, ${\\cal R}=R_{CR}/L_b$. I use a set of $N$-body+SPH simulations, including sub-grid physics, whose initial conditions cover a range of gas fractions and halo shapes. The models, by construction, have roughly the same azimuthally averaged circular velocity curve and halo density and they are all submaximal, i.e. according to previous works they are expected to have all roughly the same ${\\cal R}$ value, well outside the fast bar range (1.2 $\\pm$ 0.2). Contrary to these expectations, however, th...

  8. Sustainability labels on food products

    DEFF Research Database (Denmark)

    Grunert, Klaus G; Hieke, Sophie; Wills, Josephine

    2014-01-01

    This study investigates the relationship between consumer motivation, understanding and use of sustainability labels on food products (both environmental and ethical labels), which are increasingly appearing on food products. Data was collected by means of an online survey implemented in the UK......, human values as measured by the Schwartz value domains, and country differences. The results imply that sustainability labels currently do not play a major role in consumers’ food choices, and future use of these labels will depend on the extent to which consumers’ general concern about sustainability...

  9. The radioactive labeling of monocytes

    International Nuclear Information System (INIS)

    With the aim of studying a possible relationship between circulating monocytes and Sternberg-Reed cells investigations were started on the specific labeling of monocytes. In this thesis the literature on the pertinent data has been reviewed and a series of experiments on the monocyte labeling procedure has been described. The principles of cell labeling with radioactive compounds were discussed. 1. Total separation of the particular cell population to be labeled and subsequent labeling with a non-specific radiopharmaceutical. 2. Specific cell labeling in a mixture of cell types based on a well defined affinity of the cell under study for the radiopharmaceutical used. Next the radionuclides that can be used for cell labeling purposes were discussed with special attention for 111In and its chelates. The principles of radiodosimetry were also discussed shortly. This section was focussed on the radiation dose the labeled cells receive because of the intracellular localized radioactivity. The radiation burden is high in comparison to amounts of radiation known to affect cell viability. A newly developed method for labeling monocytes specifically by phagocytosis of 111In-Fe-colloid without apparent loss of cells was described in detail. (Auth.)

  10. Unfolding the color code

    OpenAIRE

    Kubica, Aleksander; Yoshida, Beni; Pastawski, Fernando

    2015-01-01

    The topological color code and the toric code are two leading candidates for realizing fault-tolerant quantum computation. Here we show that the color code on a $d$-dimensional closed manifold is equivalent to multiple decoupled copies of the $d$-dimensional toric code up to local unitary transformations and adding or removing ancilla qubits. Our result not only generalizes the proven equivalence for $d=2$, but also provides an explicit recipe of how to decouple independent components of the ...

  11. Hydrodynamic and geomorphic controls on mouth bar evolution

    Science.gov (United States)

    Esposito, Christopher R.; Georgiou, Ioannis Y.; Kolker, Alexander S.

    2013-04-01

    While river deltas are one of the major repositories for sediments and carbon on Earth, there exists a paucity of field data on the formation of distributary mouth bars—one of their key features. Here we present results from an experiment that tested a model of mouth bar development using hydroacoustic, optical, sedimentary, and geochemical tools on a mouth bar in a crevasse splay near the mouth of the Mississippi River. Our results validate an existing model for mouth bar development, which we extend to explain mouth bar stratigraphy. We propose that changes across a hydrological cycle are important for mouth bar development, resulting in a stratigraphy that has alternating fine and coarse grain sediments. Results also indicate that sand is carried up to 6 km from the main stem of the Mississippi River, despite repeated channel bifurcations, which has important implications for our interpretation of the rock record, understanding of coastal sedimentary systems, and the restoration of large deltas.

  12. Study of aging and embrittlement of microalloyed steel bars

    Science.gov (United States)

    Campillo, B.; Perez, R.; Martinez, L.

    1996-10-01

    The aging of hooks, anchors, and other bent reinforcing steel bars in concrete structures are considered in modern international standards. Rebend test procedures have been designed in order to predict the aging embrittlement susceptibility by submerging bent reinforcing bar specimens in boiling water. Subsequently the bars are rebent or straightened in order to determine the loss of ductility or embrittlement of the aged material. The present work considers the influence of carbon, sulfur, and niobium on the performance of reinforcing bars in rebend tests of 300 heats of microalloyed steel bars with a variety of compositions. The microstructural evidence and the statistical results clearly indicate the strong influence of carbon and sulfur on rebend failure, while niobium-rich precipitates contribute to the hardening of the ferrite grains during aging.

  13. The ratio of pattern speeds in double-barred galaxies

    CERN Document Server

    Font, Joan; Zaragoza-Cardiel, Javier; Fathi, Kambiz; Epinat, Benoît; Amram, Philippe

    2014-01-01

    We have obtained two-dimensional velocity fields in the ionized gas of a set of 8 double-barred galaxies, at high spatial and spectral resolution, using their H$\\alpha$ emission fields measured with a scanning Fabry-Perot spectrometer. Using the technique by which phase reversals in the non-circular motion indicate a radius of corotation, taking advantage of the high angular and velocity resolution we have obtained the corotation radii and the pattern speeds of both the major bar and the small central bar in each of the galaxies; there are few such measurements in the literature. Our results show that the inner bar rotates more rapidly than the outer bar by a factor between 3.3 and 3.6.

  14. Characterizing Barred Galaxies in the Abell 901/902 Supercluster

    CERN Document Server

    Marinova, I; Bacon, D; Balogh, M; Barden, M; Barazza, F D; Bell, E F; Böhm, A; Caldwell, J A R; Gray, M E; Haussler, B; Heymans, C; Jahnke, K; Van Kampen, E; Koposov, S; Lane, K; McIntosh, D H; Meisenheimer, K; Peng, C Y; Rix, H -W; Sánchez, S F; Taylor, A; Wisotzki, L; Wolf, C; Zheng, X

    2008-01-01

    In dense clusters, higher densities at early epochs as well as physical processes, such as ram pressure stripping and tidal interactions become important, and can have direct consequences for the evolution of bars and their host disks. To study bars and disks as a function of environment, we are using the STAGES ACS HST survey of the Abell 901/902 supercluster (z~0.165), along with earlier field studies based the SDSS and the Ohio State University Bright Spiral Galaxy Survey (OSUBSGS). We explore the limitations of traditional methods for characterizing the bar fraction, and in particular highlight uncertainties in disk galaxy selection in cluster environments. We present an alternative approach for exploring the proportion of bars, and investigate the properties of bars as a function of host galaxy color, Sersic index, stellar mass, star formation rate (SFR), specific SFR, and morphology.

  15. Stellar population constraints on the ages of galactic bars

    CERN Document Server

    James, Phil A

    2016-01-01

    We present a study of the stellar populations within the central regions of four nearby barred galaxies, and use a novel technique to constrain the duration of bar activity. We focus on the star formation 'desert', a region within each of these galaxies where star formation appears to have been suppressed by the bar. New H beta spectroscopic data are presented, and used to produce spectroscopic line indices which are compared with theoretical predictions from population synthesis models for simple stellar populations and temporally truncated star formation histories. This analysis shows that the dearth of star formation activity in these regions appears to have been continuing for at least 1 Gyr, with timescales of several Gyr indicated for two of the galaxies. This favours models in which strong bars can be long-lived features of galaxies, but our results also indicate a significant diversity in stellar population ages, and hence in the implied histories of bar activity in these four galaxies.

  16. Microbial contamination of "In use" bar soap in dental clinics

    Directory of Open Access Journals (Sweden)

    Hegde P

    2006-01-01

    Full Text Available Bar soap from 18 different dental clinics were investigated for microbial contamination, while it was "in-use". Of the 32 samples obtained from the bar soap, 100% yielded positive culture. A total of 8 different genera of organisms were isolated. Each bar soap was found to harbor 2-5 different genera of micro organisms. Heavily used soap had more micro organisms compared to less used soap. The microbial load of the "in-use" bar soap constituted a mixed flora of gram positive, gram negative, aerobes, anaerobes, and fungi. The results indicate that the bar soap under "in-use" condition is a reservoir of microorganisms and handwashing with such a soap may lead to spread of infection.

  17. A Monte Carlo code for ion beam therapy

    CERN Multimedia

    Anaïs Schaeffer

    2012-01-01

    Initially developed for applications in detector and accelerator physics, the modern Fluka Monte Carlo code is now used in many different areas of nuclear science. Over the last 25 years, the code has evolved to include new features, such as ion beam simulations. Given the growing use of these beams in cancer treatment, Fluka simulations are being used to design treatment plans in several hadron-therapy centres in Europe.   Fluka calculates the dose distribution for a patient treated at CNAO with proton beams. The colour-bar displays the normalized dose values. Fluka is a Monte Carlo code that very accurately simulates electromagnetic and nuclear interactions in matter. In the 1990s, in collaboration with NASA, the code was developed to predict potential radiation hazards received by space crews during possible future trips to Mars. Over the years, it has become the standard tool to investigate beam-machine interactions, radiation damage and radioprotection issues in the CERN accelerator com...

  18. Analysis of a calculation method for the determination of the value of safety or control bars; Analisis de un metodo de calculo para la determinacion del valor de barras de seguridad o control

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar H, F.; Torres A, C.; Filio L, C. [ININ, Gcia. de Reactores, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    1982-09-15

    Due to the control or safety bars in a nuclear reactor are constituted by strongly absorbent materials, the Diffusion Theory like tool for the calculation of bar values is not directly applicable, should it use the Transport Theory. However the speed and economy of the Diffusion codes for the reactors calculation, those make attractiveness and by this reason its are used in the determination of characteristic parameters and even in the determination of bar values, not without before to make some theoretical developments that allow to make applicable this theory. The application of the Diffusion Theory in strongly absorbent media is based on the use of some effective cross sections distinct from the real ones obtained when imposing the reason that among the flow and it gradient in the external surface of such media (control element in general, bar type or flagstone) be similar to the one obtained using Transport Theory in all the control region (multiplicative and absorbent media) with those real cross sections. The effective cross sections were obtained of the Leopard-NUMICE cell code which has incorporate the respective calculation theory of effective cross sections. Later these constants its were used in the bidimensional diffusion code Exterminator-II, simulating in it, the distribution of safety or control bars. From the cell code its were also obtained the respective constants of the homogeneous fuel cell. The results as soon as those obtained bar values of the diffusion code, its were compared with some experimental results obtained in the R{phi} Swedish reactor of natural uranium and heavy water. In this work an analysis of the bar value of one of them, trying to determine the applicability of the method is made. (Author)

  19. The materiality of Code

    DEFF Research Database (Denmark)

    Soon, Winnie

    2014-01-01

    to understand the socio-technical side of a changing network environment. Through the study of code, including but not limited to source code, technical specifications and other materials in relation to the artwork production, I would like to explore the materiality of code that goes beyond technical...

  20. Informal control code logic

    OpenAIRE

    Bergstra, J. A.

    2010-01-01

    General definitions as well as rules of reasoning regarding control code production, distribution, deployment, and usage are described. The role of testing, trust, confidence and risk analysis is considered. A rationale for control code testing is sought and found for the case of safety critical embedded control code.

  1. Refactoring test code

    NARCIS (Netherlands)

    Deursen, A. van; Moonen, L.M.F.; Bergh, A. van den; Kok, G.

    2001-01-01

    Two key aspects of extreme programming (XP) are unit testing and merciless refactoring. Given the fact that the ideal test code / production code ratio approaches 1:1, it is not surprising that unit tests are being refactored. We found that refactoring test code is different from refactoring product

  2. Informal Control code logic

    CERN Document Server

    Bergstra, Jan A

    2010-01-01

    General definitions as well as rules of reasoning regarding control code production, distribution, deployment, and usage are described. The role of testing, trust, confidence and risk analysis is considered. A rationale for control code testing is sought and found for the case of safety critical embedded control code.

  3. Gauge color codes

    DEFF Research Database (Denmark)

    Bombin Palomo, Hector

    2015-01-01

    Color codes are topological stabilizer codes with unusual transversality properties. Here I show that their group of transversal gates is optimal and only depends on the spatial dimension, not the local geometry. I also introduce a generalized, subsystem version of color codes. In 3D they allow the...

  4. ARC Code TI: CODE Software Framework

    Data.gov (United States)

    National Aeronautics and Space Administration — CODE is a software framework for control and observation in distributed environments. The basic functionality of the framework allows a user to observe a...

  5. ARC Code TI: ROC Curve Code Augmentation

    Data.gov (United States)

    National Aeronautics and Space Administration — ROC (Receiver Operating Characteristic) curve Code Augmentation was written by Rodney Martin and John Stutz at NASA Ames Research Center and is a modification of...

  6. Revealing galactic scale bars with the help of Galaxy Zoo

    Science.gov (United States)

    Masters, Karen L.

    2015-03-01

    We use visual classifications of the brightest 250,000 galaxies in the Sloan Digital Sky Survey Main Galaxy Sample provided by citizen scientists via the Galaxy Zoo project (www.galaxyzoo.org, Lintott et al. 2008) to identify a sample of local disc galaxies with reliable bar identifications. These data, combined with information on the atomic gas content from the ALFALFA survey (Haynes et al. 2011) show that disc galaxies with higher gas content have lower bar fractions. We use a gas deficiency parameter to show that disc galaxies with more/less gas than expected for their stellar mass are less/more likely to host bars. Furthermore, we see that at a fixed gas content there is no residual correlation between bar fraction and stellar mass. We argue that this suggests previously observed correlations between galaxy colour/stellar mass and (strong) bar fraction (e.g. from the sample in Masters et al. 2011, and also see Nair & Abraham 2010) could be driven by the interaction between bars and the gas content of the disc, since more massive, optically redder disc galaxies are observed to have lower gas contents. Furthermore we see evidence that at a fixed gas content the global colours of barred galaxies are redder than those of unbarred galaxies. We suggest that this could be due to the exchange of angular momentum beyond co-rotation which might stop a replenishment of gas from external sources, and act as a source of feedback to temporarily halt or reduce the star formation in the outer parts of barred discs. These results (published as Masters et al. 2012) combined with those of Skibba et al. (2012), who use the same sample to show a clear (but subtle and complicated) environmental dependence of the bar fraction in disc galaxies, suggest that bars are intimately linked to the evolution of disc galaxies.

  7. 21 CFR 201.2 - Drugs and devices; National Drug Code numbers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Drugs and devices; National Drug Code numbers. 201.2 Section 201.2 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL LABELING General Labeling Provisions § 201.2 Drugs and devices; National Drug...

  8. Laser labeling, a safe technology to label produce

    Science.gov (United States)

    Laser labeling of fruits and vegetables is an alternative means to label produce. Low energy CO2 laser beams etch the surface showing the contrasting underlying layer. These etched surfaces can promote water loss and potentially allow for entry of decay organisms. The long-term effects of laser labe...

  9. 76 FR 75809 - Prior Label Approval System: Generic Label Approval

    Science.gov (United States)

    2011-12-05

    ... the type of packaging material on which the label is printed; n. Brand name changes, provided that... poultry products will take effect January 1, 2012 (75 FR 82148, Dec. 29, 2010). These mandatory features..., location, and indication of final color. To obtain sketch label approval, domestic meat and...

  10. Oxygen labelled CO2

    International Nuclear Information System (INIS)

    Tests were carried out as to whether additional information concerning pulmonary gas exchange could be obtained from the application of oxygen labelled carbon dioxide. Single breath experiments were performed on two healthy subjects with 0.1 percent C16O18O and 2.8 percent C18O2 in the inspiratory gas. Breath-hold time was varied between 0.5-20s in different experiments. The 18O-concentration of the end-expired gas bi-exponentially decreased with increasing breath-hold time. The high and low rate constants 4s-1 and 0.12s-1 for C18O2 and 2.5s-1 and 0.87s-1 for C16O18O were derived, respectively. These results, together with model calculations, suggest: 1) the rapid disappearance of C18O2 from the alveolar space is primarily limited by diffusion, so that this isotopic species can be applied to quantify pulmonary diffusing conditions; 2) the lower disappearance rate of C16O18O is caused by a lower equilibration kinetics in blood, so that this isotopic species offers a possibility to study carbonic anhydrase activity of the red cells in vivo; 3) the slow phase of label decay is influenced by both alveolar dead space and carbonic anhydrase activity of the pulmonary tissues. Pathological dead spaces are expected to be sensitively detectable by C16O18O as well as by C18O2. (author). 4 refs.; 4 figs

  11. The Procions` code; Le code Procions

    Energy Technology Data Exchange (ETDEWEB)

    Deck, D.; Samba, G.

    1994-12-19

    This paper presents a new code to simulate plasmas generated by inertial confinement. This multi-kinds kinetic code is done with no angular approximation concerning ions and will work in plan and spherical geometry. First, the physical model is presented, using Fokker-Plank. Then, the numerical model is introduced in order to solve the Fokker-Plank operator under the Rosenbluth form. At the end, several numerical tests are proposed. (TEC). 17 refs., 27 figs.

  12. Lawyers for Literacy. A Bar Leadership Manual. A Special Service Publication of the American Bar Association's Task Force on Literacy.

    Science.gov (United States)

    American Bar Association, Washington, DC.

    This manual is designed to provide materials to help state and local bar associations become involved with the literacy issue. Chapter 1 provides an overview of illiteracy as a very serious problem. Chapter 2 describes major public and private efforts to combat illiteracy. Chapter 3 explains why the bar associations should be involved. Chapter 4…

  13. MKENO-DAR: a direct angular representation Monte Carlo code for criticality safety analysis

    International Nuclear Information System (INIS)

    Improving the Monte Carlo code MULTI-KENO, the MKENO-DAR (Direct Angular Representation) code has been developed for criticality safety analysis in detail. A function was added to MULTI-KENO for representing anisotropic scattering strictly. With this function, the scattering angle of neutron is determined not by the average scattering angle μ-bar of the Pl Legendre polynomial but by the random work operation using probability distribution function produced with the higher order Legendre polynomials. This code is avilable for the FACOM-M380 computer. This report is a computer code manual for MKENO-DAR. (author)

  14. Universal Rateless Codes From Coupled LT Codes

    CERN Document Server

    Aref, Vahid

    2011-01-01

    It was recently shown that spatial coupling of individual low-density parity-check codes improves the belief-propagation threshold of the coupled ensemble essentially to the maximum a posteriori threshold of the underlying ensemble. We study the performance of spatially coupled low-density generator-matrix ensembles when used for transmission over binary-input memoryless output-symmetric channels. We show by means of density evolution that the threshold saturation phenomenon also takes place in this setting. Our motivation for studying low-density generator-matrix codes is that they can easily be converted into rateless codes. Although there are already several classes of excellent rateless codes known to date, rateless codes constructed via spatial coupling might offer some additional advantages. In particular, by the very nature of the threshold phenomenon one expects that codes constructed on this principle can be made to be universal, i.e., a single construction can uniformly approach capacity over the cl...

  15. The $K \\bar K \\pi$ decay of the $f_1(1285)$ and its nature as a $K^* \\bar K -cc$ molecule

    OpenAIRE

    Aceti, F.; Xie, Ju-Jun; Oset, E

    2015-01-01

    We investigate the decay of $f_1(1285) \\to \\pi K \\bar K$ with the assumption that the $f_1(1285)$ is dynamically generated from the $K^* \\bar{K} - cc$ interaction. In addition to the tree level diagrams that proceed via $f_1(1285) \\to K^* \\bar{K} - cc \\to \\pi K \\bar K$, we take into account also the final state interactions of $K \\bar K \\to K \\bar K$ and $\\pi K \\to \\pi K$. The partial decay width and mass distributions of $f_1(1285) \\to \\pi K \\bar K$ are evaluated. We get a value for the part...

  16. (Sigma-Delta) Codes

    OpenAIRE

    Boulagouaz, M.; Leroy, A

    2013-01-01

    In this paper we introduce the notion of cyclic ($f(t),\\sigma,\\delta$)-codes for $f(t)\\in \\Ore$. These codes generalize the $\\theta$-codes as introduced by D. Boucher, F. Ulmer, W. Geiselmann \\cite{BGU}. We construct generic and control matrices for these codes. As a particular case the ($\\si,\\de$)-$W$-code associated to a Wedderburn polynomial are defined and we show that their control matrices are given by generalized Vandermonde matrices. All the Wedderburn polynomials of $\\mathbb F_q[t;\\t...

  17. Variation of Galactic Bar Length with Amplitude and Density as Evidence for Bar Growth over a Hubble Time

    CERN Document Server

    Elmegreen, Bruce G; Knapen, Johan H; Buta, Ronald J; Block, David L; Puerari, Ivanio

    2007-01-01

    K_s-band images of 20 barred galaxies show an increase in the peak amplitude of the normalized m=2 Fourier component with the R_25-normalized radius at this peak. This implies that longer bars have higher $m=2$ amplitudes. The long bars also correlate with an increased density in the central parts of the disks, as measured by the luminosity inside 0.25R_25 divided by the cube of this radius in kpc. Because denser galaxies evolve faster, these correlations suggest that bars grow in length and amplitude over a Hubble time with the fastest evolution occurring in the densest galaxies. All but three of the sample have early-type flat bars; there is no clear correlation between the correlated quantities and the Hubble type.

  18. Role of $Y(4630)$ in the $p\\bar{p}\\rightarrow\\Lambda_c\\bar{\\Lambda}_c$ reaction near threshold

    CERN Document Server

    Wang, Yan-Yan; Wang, En; li, De-Min

    2016-01-01

    We investigate the charmed baryon production reaction $p\\bar{p}\\rightarrow\\Lambda_c\\bar{\\Lambda}_c$ in an effective Lagrangian approach. Besides the $t$-channel $D^0$ and $D^{*0}$ mesons exchanges, the $s$-channel $Y(4630)$ meson exchange is taken into account. For the total cross sections, the $D^0$ and $D^{*0}$ mesons provide minor background contributions, while the $Y(4630)$ state gives a clear peak structure with the magnitude of 10 $\\mu$b at center of mass energy 4.63 GeV. Basing on the results, we suggest that the reaction of $p\\bar{p}\\rightarrow\\Lambda_c\\bar{\\Lambda}_c$ can be used to search for the $1^{--}$ charmonium-like $Y(4630)$ state, and our predictions can be tested in future by the $\\rm{\\bar PANDA}$ facility.

  19. Measurement of the $\\bar{p}p \\rightarrow \\bar{n}n$ Charge-Exchange Differential Cross-Section

    CERN Multimedia

    2002-01-01

    The aim of this proposal is a measurement of the differential cross-section of the $\\bar{p}$p $\\rightarrow$ $\\bar{n}$n charge-exchange reaction with a point-to-point precision of 1\\% in the forward direction, and an absolute normalization error of 3\\%. The high precision of the data should allow, inter alia, a determination of the $\\pi$NN coupling constant to better than 2\\%.\\\\ \\\\ The measurement will be done using the existing neutron and antineutron detectors built for experiment PS199 and liquid hydrogen target. In one week of running time, with a $\\bar{p}$ beam intensity of 3 $ 10 ^{5} $ $\\bar{p}$/sec, the reaction will be measured at a few $\\bar{p}$ momenta, in the range 500 to 900~MeV/c.

  20. Nuss bar procedure: past, present and future

    Science.gov (United States)

    Obermeyer, Robert J.; Kelly, Robert E.

    2016-01-01

    Repair of pectus excavatum began at the beginning of the 20th century before endotracheal intubation was standard practice. Surgeons therefore developed techniques that corrected the deformity using an open procedure via the anterior chest wall. Initial techniques were unsatisfactory, but by the 1930s the partial rib resection and sternal osteotomy technique had been developed and was used in combination with external traction post-operatively to prevent the sternum from sinking back into the chest. In 1949, Ravitch recommended complete resection of the costal cartilages and complete mobilization of the sternum without external traction, and in 1961 Adkins and Blades introduced the concept of a substernal strut for sternal support. The wide resection resulted in a very rigid anterior chest wall, and in some instances, the development of asphyxiating chondrodystrophy. The primary care physicians therefore became reluctant to refer the patients for repair. In 1987, Nuss developed a minimally invasive technique that required no cartilage or sternal resection and relied only on internal bracing by means of a sub-sternal bar, which is inserted into the chest through two lateral thoracic incisions and guided across the mediastinum with the help of thoracoscopy. After publication of the procedure in 1998, it became widely accepted and a flood of new patients suddenly started to appear, which allowed for rapid improvements and modifications of the technique. New instruments were developed specifically for the procedure, complications were recognized, and the steps taken to prevent them included the development of a stabilizer and the use of pericostal sutures to prevent bar displacement. Various options were developed for sternal elevation prior to mediastinal dissection to prevent injury to the mediastinal structures, allergy testing was implemented, and pain management improved. The increased number of patients coming for repair permitted studies of cardiopulmonary