Defect analysis of BaSrFBr:Eu irradiated by X-ray

International Nuclear Information System (INIS)

Lee, C. Y.; Jeong, J. M.; Kim, J. H.

2010-01-01

The mechanical property of the BaSrFBr:Eu phosphor layer of X-ray image plates was investigated by using image quality (IQ), resolution (LP/mm), and coincidence Doppler broadening (CDB) positron annihilation. The screen samples of BaSrFBr:Eu phosphors were irradiated with hospital X-rays in the course of diagnostic radiography at an average rate of 20,000 times per year and were used for various periods of time. The LP/mm values of the irradiated BaSrFBr:Eu image plates varied between 2.4 and 2.0 for three years while the IQ values varied between 35 and 11 over the same period. CDB positron annihilation spectroscopy was used to analyze the defect structures in the phosphor layer. The S parameter values increased in correlation with increased exposure time, which indicated that more defects were generated. There was a positive relationship between the IQ and S parameters. Measurements of the defects indicate that most of the defects were likely to have been generated by the X-ray radiation.

A SrBPO5: Eu2+ phosphor for neutron imaging

International Nuclear Information System (INIS)

Sakasai, K.; Katagiri, M.; Toh, K.; Nakamura, T.

2001-01-01

A SrBPO 5 : Eu 2+ phosphor material has been investigated for neutron imaging. This phosphor showed photostimulated luminescence (PSL) by illumination of 635 nm laser light after X-ray irradiation. The spectral characteristics of the phosphor were similar to those of BaFBr: Eu 2+ , which is a commonly used phosphor of imaging plates. In addition, we found that this phosphor also showed PSL for neutron irradiation. It comes from the fact that it contains atomic boron in base matrix. Therefore, this phosphor can be used for neutron imaging without adding neutron sensitive materials such as Gd in commercially available neutron imaging plates. The PSL intensity and the neutron detection will be increased by using enriched boron instead of natural boron. (author)

Infrared emissions in MgSrAl10O17:Er3+ phosphor co-doped with Yb3+/Ba2+/Ca2+ obtained by solution combustion route

International Nuclear Information System (INIS)

Singh, Vijay; Kumar Rai, Vineet; Venkatramu, V.; Chakradhar, R.P.S.; Hwan Kim, Sang

2013-01-01

An intense infrared emitting MgSrAl 10 O 17 :Er 3+ phosphor co-doped with Yb 3+ , Ba 2+ and Ca 2+ ions have been prepared by a solution combustion method. Phase purity of the derived compounds was confirmed by X-ray diffraction technique. The vibrational properties of MgSrAl 10 O 17 phosphor was studied by Fourier transform infrared spectroscopy. The broad and strong infrared emission of Er 3+ ions at around 1.53 μm was observed upon excitation at 980 nm. Effect of co-doping with the Yb 3+ , Ba 2+ and Ca 2+ ions on the infrared luminescence intensity of Er 3+ ions and the mechanism responsible for the variation in the infrared intensity have been discussed. The results indicate that these materials may be suitable for the optical telecommunication window and wavelength division multiplexing applications. - Highlights: ► The hexagonal phase of MgSrAl 10 O 17 could be obtained by the low temperature combustion method. ► The broad and strong infrared emission of Er 3+ ions at around 1.53 μm was observed. ► Effect of co-doping with the Yb 3+ , Ba 2+ and Ca 2+ ions on the infrared luminescence intensity of Er 3+ were reported.

High-Throughput Synthesis and Characterization of Eu Doped Ba xSr2- xSiO4 Thin Film Phosphors.

Science.gov (United States)

Frost, Sara; Guérin, Samuel; Hayden, Brian E; Soulié, Jean-Philippe; Vian, Chris

2018-06-20

High-throughput techniques have been employed for the synthesis and characterization of thin film phosphors of Eu-doped Ba x Sr 2- x SiO 4 . Direct synthesis from evaporation of the constituent elements under a flux of atomic oxygen on a sapphire substrate at 850 °C was used to directly produce thin film libraries (415 nm thickness) of the crystalline orthosilicate phase with the desired compositional variation (0.24 > x > 1.86). The orthosilicate phase could be synthesized as a pure, or predominantly pure, phase. Annealing the as synthesized library in a reducing atmosphere resulted in the reduction of the Eu while retaining the orthosilicate phase, and resulted in a materials thin film library where fluorescence excited by blue light (450 nm) was observable by the naked eye. Parallel screening of the fluorescence from the combinatorial libraries of Eu doped Ba x Sr 2- x SiO 4 has been implemented by imaging the fluorescent radiation over the library using a monochrome digital camera using a series of color filters. Informatics tools have been developed to allow the 1931 CIE color coordinates and the relative quantum efficiencies of the materials library to be rapidly assessed and mapped against composition, crystal structure and phase purity. The range of compositions gave values of CIE x between 0.17 and 0.52 and CIE y between 0.48 and 0.69 with relative efficiencies in the range 2.0 × 10 -4 -7.6 × 10 -4 . Good agreement was obtained between the thin film phosphors and the fluorescence characteristics of a number of corresponding bulk phosphor powders. The thermal quenching of fluorescence in the thin film libraries was also measured in the temperature range 25-130 °C: The phase purity of the thin film was found to significantly influence both the relative quantum efficiency and the thermal quenching of the fluorescence.

Structures and self-activating photoluminescent properties of Sr3−xAxGaO4F (A=Ba, Ca) materials

International Nuclear Information System (INIS)

Green, Robert; Vogt, Thomas

2012-01-01

The synthesis, structures and photoluminescent properties of mixed oxyfluorides of the type Sr 3−x A x GaO 4 F are compared to Sr 3−x A x AlO 4 F (A=Ca, Ba) materials. In these compounds the F − and O 2− ions are ordered and located on two distinct crystallographic sites. When substituting Sr 2+ by Ba 2+ and Ca 2+ , we find in Sr 3−x A x GaO 4 F materials an ordering of the alkaline earth cations over the two crystallographic sites. The amount of Ba 2+ ions that can be substituted into Sr 3−x A x GaO 4 F is x≤1.2, which is slightly more than can be incorporated into the previously reported Al-analog Sr 3−x A x AlO 4 F (x=1.0). Conversely, the amount of Ca 2+ ions that can be substituted into Sr 3−x Ca x GaO 4 F (x=0.3) is significantly less than in Sr 3−x Ca x AlO 4 F (x=1.0). A post-synthesis reduction step causes these materials to exhibit self-activating broad band photoluminescence where the emitted colors vary with the amount of ions substituted into the host lattice. - Graphical abstract: TOC Statement The structures of the self-activating phosphors Sr 3−x A x MO 4 F (A=Ba, Ca and M=Al, Ga) can be rationalized as alternating layers of bond compression and elongation, which impact the photoluminescence. Highlights: ► Comparison of the structural changes in Sr 3−x A x AlO 4 F and Sr 3−x A x GaO 4 F (A=Ba, Ca) and its influence on the photoluminescence of these self-activating phosphors. ► Analysis of the Global Instability Index of the Sr 3−x A x AlO 4 F and Sr 3−x A x GaO 4 F (A=Ba, Ca). ► Comparison of the photoluminescence between the self-activating phosphors Sr 3−x A x AlO 4 F and Sr 3−x A x GaO 4 F (A=Ba, Ca).

Tuning the luminescence color and enhancement of afterglow properties of Sr(4−x−y)CaxBayAl14O25:Eu2+,Dy3+ phosphor by adjusting the composition

International Nuclear Information System (INIS)

Luitel, Hom Nath; Watari, Takanori; Chand, Rumi; Torikai, Toshio; Yada, Mitsunori; Mizukami, Hiroshi

2013-01-01

Graphical abstract: Excitation and fluorescence emission spectra of three extreme compositions of Ca, Sr and Ba in Sr 4 Al 14 O 25 phosphor (viz. 4CaO·7Al 2 O 3 , 4SrO·7Al 2 O 3 and 4BaO·7Al 2 O 3 ) doped with 4 at% Eu 2+ and 8 at% Dy 3+ (inset shows the digital micrograph of corresponding phosphors). -- Highlights: • Bright phosphor, Sr (4−x−y) Ca x Ba y Al 14 O 25 :Eu 2+ ,Dy 3+ , was synthesized by adjusting the composition. • The solid solubility of Ca and Ba in the Sr 4 Al 14 O 25 host was determined to be 20 and 10 mol%, respectively. • Substituting part of Sr by Ca, the emission color can be well tuned from blue to green. • A white afterglow was observed when 3.2 mol of Sr was substituted by Ca. • The afterglow luminescence was enhanced by 1.5 times by 0.2 mol Ca substitution. -- Abstract: Color point tuning is an important challenge for improving the practical applications of various displays, especially there are very limited white color single hosts that emits in the white spectrum. In this paper, the possibility of color tuning by substituting part of host lattice cation (Sr 2+ ions) by Ca 2+ or Ba 2+ ions in an efficient strontium aluminate phosphor, Sr 4 Al 14 O 25 :Eu 2+ ,Dy 3+ , is reported and found to be very promising for displays. A detail study by replacing part of Sr 2+ with Ca 2+ or Ba 2+ has been investigated. X-ray diffraction study showed that crystal structure of Sr 4 Al 14 O 25 is preserved up to 20 mol of Ca 2+ ion exchange while it is limited to 10 mol of Ba 2+ ions exchange. Substantial shift in the emission band and color were observed by substitution of Sr 2+ by Ca 2+ or Ba 2+ ions. A bluish-white emission and afterglow was observed at higher Ca 2+ ions substitution. Further, partial Ca 2+ substitutions (up to 0.8 mol) resulted in enhanced afterglow of Sr 4 Al 14 O 25 :Eu 2+ ,Dy 3+ phosphor. However, Ba 2+ substitution decreased the fluorescence as well afterglow of the Sr 4 Al 14 O 25 :Eu 2+ ,Dy 3+ phosphor

Metaheuristics-Assisted Combinatorial Screening of Eu2+-Doped Ca-Sr-Ba-Li-Mg-Al-Si-Ge-N Compositional Space in Search of a Narrow-Band Green Emitting Phosphor and Density Functional Theory Calculations.

Science.gov (United States)

Lee, Jin-Woong; Singh, Satendra Pal; Kim, Minseuk; Hong, Sung Un; Park, Woon Bae; Sohn, Kee-Sun

2017-08-21

A metaheuristics-based design would be of great help in relieving the enormous experimental burdens faced during the combinatorial screening of a huge, multidimensional search space, while providing the same effect as total enumeration. In order to tackle the high-throughput powder processing complications and to secure practical phosphors, metaheuristics, an elitism-reinforced nondominated sorting genetic algorithm (NSGA-II), was employed in this study. The NSGA-II iteration targeted two objective functions. The first was to search for a higher emission efficacy. The second was to search for narrow-band green color emissions. The NSGA-II iteration finally converged on BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphors in the Eu 2+ -doped Ca-Sr-Ba-Li-Mg-Al-Si-Ge-N compositional search space. The BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphor, which was synthesized with no human intervention via the assistance of NSGA-II, was a clear single phase and gave an acceptable luminescence. The BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphor as well as all other phosphors that appeared during the NSGA-II iterations were examined in detail by employing powder X-ray diffraction-based Rietveld refinement, X-ray absorption near edge structure, density functional theory calculation, and time-resolved photoluminescence. The thermodynamic stability and the band structure plausibility were confirmed, and more importantly a novel approach to the energy transfer analysis was also introduced for BaLi 2 Al 2 Si 2 N 6 :Eu 2+ phosphors.

Luminescence properties of Sr{sub 3-x-3y/2}M{sub x}Ce{sub y}AlO{sub 4}F (M=Ca, Ba, 0{<=}x{<=}0.9, 0.001{<=}y{<=}0.05) phosphors

Energy Technology Data Exchange (ETDEWEB)

Choi, Hye-Min [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Park, Sangmoon, E-mail: spark@silla.ac.kr [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of)

2012-09-15

Luminescent materials composed of Sr{sub 3-x-3y/2}M{sub x}Ce{sub y}AlO{sub 4}F (M=Ca, Ba, 0{<=}x{<=}0.9, 0.001{<=}y{<=}0.05) were prepared by the solid-state reaction method. X-ray diffraction (XRD) patterns of the obtained oxyfluorides are exhibited for indexing peak positions. Dynamic excitation and emission spectra of the Ce{sup 3+}-activated oxyfluoride phosphors are clearly monitored. The critical emission quenching as a function of Ce{sup 3+} contents in Sr{sub 2.5-3y/2}M{sub 0.5}Ce{sub y}AlO{sub 4}F phosphors is revealed at quite low concentrations of the activator. CIE coordinates of blue and green Sr{sub 2.5-3y/2}M{sub 0.5}Ce{sub y}AlO{sub 4}F phosphors are clearly measured. The relative quantum efficiency of Sr{sub 2.4985}Ca{sub 0.5}Ce{sub 0.005}AlO{sub 4}F based on the integrated emission is determined. The Sr{sub 3-x-3y/2}M{sub x}Ce{sub y}AlO{sub 4}F phosphors excited near 410 nm light could be prominent phosphors in applications of NUV-LED. - Highlights: Black-Right-Pointing-Pointer Blue and green emitting oxyfluoride phosphors are excitated near 410 nm Black-Right-Pointing-Pointer Ce{sup 3+}-activated oxyfluoride phosphors are quite effective to prepare white light for near-UV LED applications. Black-Right-Pointing-Pointer Gradual substitution of Ce{sup 3+} content in the oxyfluoride hosts changes CIE values.

Luminescent properties of Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}AlO{sub 4}F oxyfluorides

Energy Technology Data Exchange (ETDEWEB)

Park, Sangmoon, E-mail: spark@silla.ac.kr [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of)

2012-04-15

Effective orange Sm{sup 3+}-doped Sr{sub 2.5}Ba{sub 0.5}AlO{sub 4}F phosphors excited at 254 and 408 nm excitation were prepared by the solid-state method. The excitation and emission spectra of Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}AlO{sub 4}F and Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}AlO{sub 4-{alpha}}F{sub 1-{delta}} (x=0.001{approx}0.1) based on photoluminescence spectroscopy are investigated. The defects in anion-deficient Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}AlO{sub 4-{alpha}}F{sub 1-{delta}} (x=0.001, 0.01) are monitored by broad-band photoluminescence emission centered near 480 nm along with the orange emission transitions of Sm{sup 3+}. CIE values and relative luminescent intensities of Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}AlO{sub 4}F and Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}AlO{sub 4-{alpha}}F{sub 1-{delta}} by changing the Sm{sup 3+} content (x=0.001{approx}0.1) are discussed. - Highlights: Black-Right-Pointing-Pointer Under the excitation of 408 nm competent orange emitting Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}AlO{sub 4}F phosphor is initiated. Black-Right-Pointing-Pointer Sm{sup 3+}-activated oxyfluoride phosphor is quite effective to prepare white-emitting light for near-UV LED applications. Black-Right-Pointing-Pointer Defects could be visibly created in the Sr{sub 2.5-3x/2}Ba{sub 0.5}Sm{sub x}Al O{sub 4}F host lattices when Sm{sup 3+} ions are doped less than 5 mol %. Black-Right-Pointing-Pointer The gradual substitution of Sm{sup 3+} contents in oxyfluoride hosts is amenable to change CIE values and desired emitting intensity.

Photoluminescence and phosphorescence properties of MAl2O4:Eu2+, Dy3+ (M=Ca, Ba, Sr) phosphors prepared at an initiating combustion temperature of 500 deg. C

International Nuclear Information System (INIS)

Mothudi, B.M.; Ntwaeaborwa, O.M.; Botha, J.R.; Swart, H.C.

2009-01-01

Eu 2+ and Dy 3+ co-doped calcium aluminate, barium aluminate and strontium aluminate phosphors were synthesized at an initiating combustion temperature of 500 deg. C using urea as an organic fuel. The crystallinity of the phosphors was investigated by using X-ray diffraction (XRD) and the morphology was determined by a scanning electron microscope (SEM). The low temperature monoclinic structure for both CaAl 2 O 4 and SrAl 2 O 4 and the hexagonal structure of BaAl 2 O 4 were observed. The effect of the host materials on the photoluminescence (PL) and phosphorescence properties were investigated by using a He-Cd Laser and a Cary Eclipse fluorescence spectrophotometer, respectively. The broad band emission spectra observed at 449 nm for CaAl 2 O 4 :Eu 2+ , Dy 3+ , 450 nm (with a shoulder-peak at 500 nm) for BaAl 2 O 4 :Eu 2+ , Dy 3+ and 528 nm for SrAl 2 O 4 :Eu 2+ , Dy 3+ are attributed to the 4f 6 5d 1 to 4f 7 transition in the Eu 2+ ion in the different hosts.

Origin of thermal degradation of Sr 2-xSi 5N 8 : Eu x phosphors in air for light-emitting diodes

NARCIS (Netherlands)

Yeh, C.W.; Chen, W.T.; Liu, R.S.; Hu, S.F.; Sheu, H.S.; Chen, J.M.; Hintzen, H.T.

2012-01-01

The orange-red emitting phosphors based on M 2Si 5N 8:Eu (M = Sr, Ba) are widely utilized in white light-emitting diodes (WLEDs) because of their improvement of the color rendering index (CRI), which is brilliant for warm white light emission. Nitride-based phosphors are adopted in high-performance

Infrared emissions in MgSrAl{sub 10}O{sub 17}:Er{sup 3+} phosphor co-doped with Yb{sup 3+}/Ba{sup 2+}/Ca{sup 2+} obtained by solution combustion route

Energy Technology Data Exchange (ETDEWEB)

Singh, Vijay, E-mail: vijayjiin2006@yahoo.com [Physical Chemistry, Institute for Pure and Applied Chemistry and Center of Interface Science, University of Oldenburg, 26129 Oldenburg (Germany); Kumar Rai, Vineet [Department of Applied Physics, Indian School of Mines, Dhanbad 826 004 (India); Venkatramu, V. [Department of Physics, Yogi Vemana University, Kadapa 516 003 (India); Chakradhar, R.P.S. [CSIR-National Aerospace, Bangalore 560 017 (India); Hwan Kim, Sang [Department of Chemical Engineering, Konkuk University, Seoul 143-701 (Korea, Republic of)

2013-02-15

An intense infrared emitting MgSrAl{sub 10}O{sub 17}:Er{sup 3+} phosphor co-doped with Yb{sup 3+}, Ba{sup 2+} and Ca{sup 2+} ions have been prepared by a solution combustion method. Phase purity of the derived compounds was confirmed by X-ray diffraction technique. The vibrational properties of MgSrAl{sub 10}O{sub 17} phosphor was studied by Fourier transform infrared spectroscopy. The broad and strong infrared emission of Er{sup 3+} ions at around 1.53 {mu}m was observed upon excitation at 980 nm. Effect of co-doping with the Yb{sup 3+}{sub ,} Ba{sup 2+} and Ca{sup 2+} ions on the infrared luminescence intensity of Er{sup 3+} ions and the mechanism responsible for the variation in the infrared intensity have been discussed. The results indicate that these materials may be suitable for the optical telecommunication window and wavelength division multiplexing applications. - Highlights: Black-Right-Pointing-Pointer The hexagonal phase of MgSrAl{sub 10}O{sub 17} could be obtained by the low temperature combustion method. Black-Right-Pointing-Pointer The broad and strong infrared emission of Er{sup 3+} ions at around 1.53 {mu}m was observed. Black-Right-Pointing-Pointer Effect of co-doping with the Yb{sup 3+}{sub ,} Ba{sup 2+} and Ca{sup 2+} ions on the infrared luminescence intensity of Er{sup 3+} were reported.

Quantitative analysis of UV excitation bands for red emissions in Pr3+-doped CaTiO3, SrTiO3 and BaTiO3 phosphors by peak fitting

International Nuclear Information System (INIS)

Fujiwara, Rei; Sano, Hiroyuki; Shimizu, Mikio; Kuwabara, Makoto

2009-01-01

A quantitative spectral analysis of the ultraviolet (UV) broad excitation bands, which are located in the range 300-400 nm, for red emissions at around 610 nm in Pr-doped CaTiO 3 , SrTiO 3 :Al and BaTiO 3 :Mg phosphors has been carried out using a peak fitting technique. The obtained results demonstrate that the UV broad band of CaTiO 3 :Pr consists of four primary excitation bands centered around 330, 335, 365 and 380 nm and those of both SrTiO 3 :Al and BaTiO 3 :Mg consist of three primary bands centered around 310, 345 and 370 nm. Based on the behavior patterns and the values of the respective primary excitation bands' parameters, i.e. center gravity (λ top ), maximum height (I max ) and full-width at half-maximum (FWHM), the UV-to-red relaxation processes in these titanate phosphors can be explained to be essentially the same, except for the existence of an additional relaxation pathway via electron-trap states in CaTiO 3 :Pr, which gives a characteristic shape of its UV excitation spectrum in the wavelength range of >360 nm

Novel yellow-emitting Sr8MgLn(PO4)7:Eu2+ (Ln=Y, La) phosphors for applications in white LEDs with excellent color rendering index.

Science.gov (United States)

Huang, Chien-Hao; Chen, Teng-Ming

2011-06-20

Eu(2+)-activated Sr(8)MgY(PO(4))(7) and Sr(8)MgLa(PO(4))(7) yellow-emitting phosphors were successfully synthesized by solid-state reactions for applications in excellent color rendering index white light-emitting diodes (LEDs). The excitation and reflectance spectra of these phosphors show broad band excitation and absorption in the 250-450 nm near-ultraviolet region, which is ascribed to the 4f(7) → 4f(6)5d(1) transitions of Eu(2+). Therefore, these phosphors meet the application requirements for near-UV LED chips. Upon excitation at 400 nm, the Sr(8)MgY(PO(4))(7):Eu(2+) and Sr(8)MgLa(PO(4))(7):Eu(2+) phosphors exhibit strong yellow emissions centered at 518, 610, and 611 nm with better thermal stability than (Ba,Sr)(2)SiO(4) (570 nm) commodity phosphors. The composition-optimized concentrations of Eu(2+) in Sr(8)MgLa(PO(4))(7):Eu(2+) and Sr(8)MgY(PO(4))(7):Eu(2+) phosphors were determined to be 0.01 and 0.03 mol, respectively. A warm white-light near-UV LED was fabricated using a near-UV 400 nm chip pumped by a phosphor blend of blue-emitting BaMgAl(10)O(17):Eu(2+) and yellow-emitting Sr(8)MgY(PO(4))(7):0.01Eu(2+) or Sr(8)MgLa(PO(4))(7):0.03Eu(2+), driven by a 350 mA current. The Sr(8)MgY(PO(4))(7):0.01Eu(2+) and Sr(8)MgLa(PO(4))(7):0.03Eu(2+) containing LEDs produced a white light with Commission International de I'Eclairage (CIE) chromaticity coordinates of (0.348, 0.357) and (0.365, 0.328), warm correlated color temperatures of 4705 and 4100 K, and excellent color rendering indices of 95.375 and 91.75, respectively. © 2011 American Chemical Society

Development of BaSO4:Eu thermoluminescence phosphor

International Nuclear Information System (INIS)

Madhusoodanan, U.; Jose, M.T.; Lakshmanan, A.R.

1999-01-01

A highly sensitive thermoluminescence (TL) phosphor based on BaSO 4 :Eu was developed following the coprecipitation technique and firing in argon atmosphere at 1123 K. Photoluminescence studies confirm that firing in argon atmosphere instead of air increased the incorporation of Eu ions in 2+ valence state. At low γ-ray doses, its TL sensitivity is nearly 2 to 3 times higher than that of CaSO 4 :Dy phosphor. The other salient features of this BaSO 4 :Eu TL phosphor are a constant glow curve shape and a nearly linear γ-ray dose response

Synthesis of novel Dy3+ activated phosphate phosphors for NUV excited LED

International Nuclear Information System (INIS)

Shinde, K.N.; Dhoble, S.J.; Kumar, Animesh

2011-01-01

The new trivalent dysprosium activated X 6 AlP 5 O 20 (where X=Sr, Ba, Ca and Mg) phosphors were prepared by the combustion method. The prepared phosphors are characterized by XRD, photoluminescence and SEM techniques. Excited by 350 nm near-ultraviolet (NUV) light, the phosphors show an efficient blue and yellow band emissions, which originates from the 4 F 9/2 → 6 H 15/2 and 4 F 9/2 → 6 H 13/2 transitions of Dy 3+ ion, respectively. The excitation spectra of the phosphors are broadband extending from 340 to 400 nm, which are characteristics of NUV excited LED. The effect of the Dy 3+ concentration on the luminescence properties of X 6 AlP 5 O 20 :Dy 3+ (where X=Sr, Ba, Ca and Mg) phosphors is studied. Ca 6 AlP 5 O 20 phosphors show strong PL emission intensity around 25 times more as compared to Ba 6 AlP 5 O 20 , Sr 6 AlP 5 O 20 and Mg 6 AlP 5 O 20 phosphors. The investigated prepared phosphors are suitable for a NUV excited LED. - Research highlights: → Novel Dy 3+ activated X 6 AlP 5 O 20 (where X=Sr,Ba,Ca and Mg) phosphors were prepared by combustion method which is very low cost and time saving synthesis method. → The excitation spectra of the phosphors are broad band extending from 340 nm to 400 nm, which is characteristics of NUV excited LED. → PL emission spectra show two emissions (485 and 573 nm) and X 6 AlP 5 O 20 :Dy 3+ 0.5 mol% (where X=Sr,Ba,Ca and Mg) phosphors shows strongest PL emission intensity. → SEM analysis indicates that phosphor particles have irregular shape, porous morphology and less than 3-4 μm in size, which is suitable for the solid state lighting (coating purpose).

Luminescent phosphors, based on rare earth substituted oxyfluorides in the A(1)3-x A(2)xMO4F family with A(1)/A(2)=Sr, Ca, Ba and M=Al, Ga

International Nuclear Information System (INIS)

Park, Sangmoon; Vogt, Thomas

2009-01-01

A new family of UV-activated phosphors made by substituting rare-earth activators such as trivalent Eu, Tb, Tm and Er into A(1) 3-x A(2) x MO 4 F host lattices (A(1)/A(2)=Sr, Ca, Ba; M=Al, Ga) are introduced and their activation and emission spectra as well as their CIE values reported. The Tm-substituted system can be activated using light with a wavelength of 360 nm. Relative intensities of a family of Tb-substituted green phosphors activated at 254 nm and with emissions centered near 548 nm are discussed.

Development of BaSO sub 4 :Eu thermoluminescence phosphor

CERN Document Server

Madhusoodanan, U; Lakshmanan, A R

1999-01-01

A highly sensitive thermoluminescence (TL) phosphor based on BaSO sub 4 :Eu was developed following the coprecipitation technique and firing in argon atmosphere at 1123 K. Photoluminescence studies confirm that firing in argon atmosphere instead of air increased the incorporation of Eu ions in 2+ valence state. At low gamma-ray doses, its TL sensitivity is nearly 2 to 3 times higher than that of CaSO sub 4 :Dy phosphor. The other salient features of this BaSO sub 4 :Eu TL phosphor are a constant glow curve shape and a nearly linear gamma-ray dose response.

Photoluminescence and phosphorescence properties of MAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} (M=Ca, Ba, Sr) phosphors prepared at an initiating combustion temperature of 500 deg. C

Energy Technology Data Exchange (ETDEWEB)

Mothudi, B.M., E-mail: mothudibm@qwa.uovs.ac.z [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Ntwaeaborwa, O.M. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Botha, J.R. [Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth, ZA 6031 (South Africa); Swart, H.C., E-mail: swarthc.sci@ufs.ac.z [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa)

2009-12-01

Eu{sup 2+} and Dy{sup 3+} co-doped calcium aluminate, barium aluminate and strontium aluminate phosphors were synthesized at an initiating combustion temperature of 500 deg. C using urea as an organic fuel. The crystallinity of the phosphors was investigated by using X-ray diffraction (XRD) and the morphology was determined by a scanning electron microscope (SEM). The low temperature monoclinic structure for both CaAl{sub 2}O{sub 4} and SrAl{sub 2}O{sub 4} and the hexagonal structure of BaAl{sub 2}O{sub 4} were observed. The effect of the host materials on the photoluminescence (PL) and phosphorescence properties were investigated by using a He-Cd Laser and a Cary Eclipse fluorescence spectrophotometer, respectively. The broad band emission spectra observed at 449 nm for CaAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+}, 450 nm (with a shoulder-peak at 500 nm) for BaAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} and 528 nm for SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} are attributed to the 4f{sup 6}5d{sup 1} to 4f{sup 7} transition in the Eu{sup 2+} ion in the different hosts.

Synthesis and photoluminescence of Sm3+ doped alkali alkaline earth borate hosts NaBa4 (BO3)3 and LiSr4(BO3)3

International Nuclear Information System (INIS)

Chauhan, A.V.; Nagpure, P.A.; Omanwar, S.K.

2012-01-01

In this paper we report the photoluminescence of Sm 3+ doped alkali alkaline borate hosts NaBa 4 (BO 3 ) 3 and LiSr 4 (BO 3 ) 3 . For the synthesis of alkali alkaline borate hosts NaBa 4 (BO 3 ) 3 and LiSr 4 (BO 3 ) 3 doped with different concentrations of Sm 3+ ions, we used the novel combustion technique. The phase purity of the hosts was confirmed by the powder XRD technique. The photoluminescence of the phosphors were carried out within 300 to 700 nm wavelength range. The phosphor shows intense orange red (602 nm) emission for near UV excitation. The FTIR spectra of the phase pure hosts have also been reported. (author)

Luminescent phosphors, based on rare earth substituted oxyfluorides in the A(1){sub 3-x} A(2){sub x}MO{sub 4}F family with A(1)/A(2)=Sr, Ca, Ba and M=Al, Ga

Energy Technology Data Exchange (ETDEWEB)

Park, Sangmoon, E-mail: spark@silla.ac.k [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Vogt, Thomas [NanoCenter and Department of Chemistry and Biochemistry, University of South Carolina, Columbia 29208, SC (United States)

2009-09-15

A new family of UV-activated phosphors made by substituting rare-earth activators such as trivalent Eu, Tb, Tm and Er into A(1){sub 3-x}A(2){sub x}MO{sub 4}F host lattices (A(1)/A(2)=Sr, Ca, Ba; M=Al, Ga) are introduced and their activation and emission spectra as well as their CIE values reported. The Tm-substituted system can be activated using light with a wavelength of 360 nm. Relative intensities of a family of Tb-substituted green phosphors activated at 254 nm and with emissions centered near 548 nm are discussed.

(Ba+Sr)/Ti ratio dependence of the dielectric properties for (Ba0.5Sr0.5)TiO3 thin films prepared by ion beam sputtering

Science.gov (United States)

Yamamichi, Shintaro; Yabuta, Hisato; Sakuma, Toshiyuki; Miyasaka, Yoichi

1994-03-01

(Ba0.5Sr0.5)TiO3 thin films were prepared by ion beam sputtering from powder targets with (Ba+Sr)/Ti ratios ranging from 0.80 to 1.50. All of the perovskite (Ba,Sr)TiO3 films were single phase except for the film with a (Ba+Sr)/Ti ratio of 1.41. The dielectric constant values notably depended on the (Ba+Sr)/Ti ratio for films thicker than 70 nm. The highest dielectric constant of 580 was achieved for the 5% (Ba+Sr) rich film. This (Ba+Sr)/Ti ratio dependence was diminished by the thickness dependence for thinner films. The grain sizes for the 9% (Ba+Sr) rich film and for the 6% (Ba+Sr) poor film ranged from 70 to 100 nm and from 30 to 60 nm, respectively. This grain size difference could explain why slightly A-site rich (Ba,Sr)TiO3 films have a larger dielectric constant than A-site poor films.

Luminescent Afterglow Behavior in the M2Si5N8: Eu Family (M = Ca, Sr, Ba

Directory of Open Access Journals (Sweden)

Koen Van den Eeckhout

2011-05-01

Full Text Available Persistent luminescent materials are able to emit light for hours after being excited. The majority of persistent phosphors emit in the blue or green region of the visible spectrum. Orange- or red-emitting phosphors, strongly desired for emergency signage and medical imaging, are scarce. We prepared the nitrido-silicates Ca2Si5N8:Eu (orange, Sr2Si5N8:Eu (reddish, Ba2Si5N8:Eu (yellowish orange, and their rare-earth codoped variants (R = Nd, Dy, Sm, Tm through a solid state reaction, and investigated their luminescence and afterglow properties. In this paper, we describe how the persistent luminescence is affected by the type of codopant and the choice and ratio of the starting products. All the materials exhibit some form of persistent luminescence, but for Sr2Si5N8:Eu,R this is very weak. In Ba2Si5N8:Eu the afterglow remains visible for about 400 s, and Ca2Si5N8:Eu,Tm shows the brightest and longest afterglow, lasting about 2,500 s. For optimal persistent luminescence, the dopant and codopant should be added in their fluoride form, in concentrations below 1 mol%. A Ca3N2 deficiency of about 5% triples the afterglow intensity. Our results show that Ba2Si5N8:Eu(,R and Ca2Si5N8:Eu(,R are promising persistent phosphors for applications requiring orange or red light.

Structural distortions in Sr3-xAxMO4F (A=Ca, Ba; M=Al, Ga, In) anti-Perovskites and corresponding changes in photoluminescence

International Nuclear Information System (INIS)

Sullivan, Eirin; Avdeev, Maxim; Vogt, Thomas

2012-01-01

The ordered oxyfluoride family Sr 3 − x A x MO 4 F (A=Ca, Ba and M=Al, Ga) has formed the basis of several new inorganic phosphors, and shows great potential for use in phosphor-conversion LED lamp devices. This study examines the correlation between subtle structural changes and photoluminescent behaviour in some of these materials. In order to ascertain whether cation charge compensation has any influence on structure and subsequent photoluminescent behaviour, a comparison was carried out between phases with the nominal compositions Sr 2.975 Ce 0.025 AlO 4 F and Sr 2.95 Ce 0.025 Na 0.025 AlO 4 F using structural characterisation based upon high-resolution neutron powder diffraction (NPD) data. Additionally, NPD data has been used to elucidate the role of different M cations in these materials, using Sr 2.25 Ba 0.6 Eu 0.1 M 0.95 In 0.05 O 4−α F 1−δ (M=Al, Ga) to determine the effect M cation size has on structure and photoluminescent properties. - Graphical abstract: The structure of Sr3-xAxMO4F (A=Ca, Ba and M=Al, Ga) and excitation and emission spectra for Sr 2.25 Ba 0.6 Eu 0.1 Ga 0.95 In 0.05 O 4−α F 1−δ . Highlights: ► Correlation between structural changes and photoluminescence in Sr 3−x A x MO 4 F (A=Ca, Ba, M=Al, Ga). ► Comparison of Sr 2.975 Ce 0.025 AlO 4 F and Sr 2.95 Ce 0.025 Na 0.025 AlO 4 F using high-resolution NPD. ► Study of the effect of cation charge-compensation on structure and photoluminescent behaviour. ► Examination of high-resolution NPD data for Sr 2.25 Ba 0.6 Eu 0.1 M 0.95 In 0.05 O 4−α F 1−δ (M=Al, Ga). ► Determination of the effect M cation size has on structure and photoluminescent properties.

High efficiency nitride based phosphores for white LEDs

NARCIS (Netherlands)

Li, Yuan Qiang; Hintzen, H.T.J.M.

2008-01-01

In this overview paper, novel rare-earth doped silicon nitride based phosphors for white LEDs applications have been demonstrated. The luminescence properties of orange-red-emitting phosphors (M2Si5N8:Eu2+) and green-to-yellow emitting phosphors (MSi2N2O2:Eu2+, M = Ca, Sr, Ba) are discussed in

Synthesis, structure, and luminescence properties of SrSiAl2O3N2:Eu(2+) phosphors for light-emitting devices and field emission displays.

Science.gov (United States)

Wang, Xicheng; Zhao, Zhengyan; Wu, Quansheng; Li, Yanyan; Wang, Chuang; Mao, Aijun; Wang, Yuhua

2015-06-28

A series of SrSiAl2O3N2:Eu(2+) (0.005 ≤x≤ 0.05) phosphors were successfully synthesized through a pressureless, facile, and efficient solid state route. The crystal structure, band structure, and their photoluminescence and cathodoluminescence properties were investigated in detail. The phosphors exhibit rod shape morphology with a uniform Eu(2+) distribution. Under n-UV excitation the emission spectra shift from 477 to 497 nm with an increase of Eu(2+) concentration. The concentration quenching mechanism of Eu(2+) emission was dominated by the dipole-dipole interaction. The thermal stability is comparable to that of the commercial Ba2SiO4:Eu(2+) phosphor. The phosphor also exhibits high current saturation and high resistance under low voltage electron bombardment. All the results indicate that the SrSiAl2O3N2:Eu(2+) phosphors can be considered as candidates for application in both white LEDs and FEDs.

Wet chemical synthesis of LiBaF{sub 3} phosphor

Energy Technology Data Exchange (ETDEWEB)

Singh, Vartika S., E-mail: svmoharil@yahoo.com [Physics Department, Shri Ramdeobaba K.N. Engineering College, Katol Road, Nagpur 440 013 (India); Joshi, C.P. [Physics Department, Shri Ramdeobaba K.N. Engineering College, Katol Road, Nagpur 440 013 (India); Moharil, S.V. [Department of Physics, R.T.M. Nagpur University, Nagpur 440 010 (India)

2013-12-05

Highlights: •LiBaF{sub 3}:RE{sup 3+} phosphors synthesized by a simple wet chemical method. •Ce{sup 3+} and Tb{sup 3+} emissions observed in as-prepared powders without any thermal treatment. •Intense Eu{sup 2+} emission observed after annealing in reductive atmosphere. -- Abstract: LiBaF{sub 3} has great potential applications as X-ray storage phosphor, slow neutron imaging, scintillator, vacuum ultraviolet (VUV) optical lithography, etc. Conventionally, LiBaF{sub 3} is prepared by solid state reaction between the constituent fluorides. However, the preparation of phase pure material and especially single crystals is rather tricky due to incongruent melting. For the first time, a wet chemical preparation of rare earth activated LiBaF{sub 3} is described here. As precipitated powders containing Ce{sup 3+} or Tb{sup 3+} exhibited characteristic luminescence. For observing Eu{sup 2+} emission, it was necessary to heat the powders in a reductive atmosphere. It is suggested that phosphors prepared by this method may prove useful in applications like OSL, X-ray imaging, etc. which do not require large single crystals.

New Silicate Phosphors for a White LED(Electronic Displays)

OpenAIRE

Toda, Kenji; Kawakami, Yoshitaka; Kousaka, Shin-ichiro; Ito, Yutaka; Komeno, Akira; Uematsu, Kazuyoshi; Sato, Mineo

2006-01-01

We focus on the development of new silicate phosphors for a white LED. In the europium doped silicate system, four LED phosphor candidates-Li_2SrSiO_4:Eu^, Ba_9Sc_2Si_6O_:Eu^, Ca_3Si_2O_7:Eu^ and Ba_2MgSi_2O_7:Eu^ were found. Luminescent properties under near UV and visible excitation were investigated for the new Eu^ doped LED silicate phosphors. These new phosphors have a relatively strong absorption band in a long wavelength region.

Electronic structure of Ca, Sr, and Ba under pressure.

Science.gov (United States)

Animalu, A. O. E.; Heine, V.; Vasvari, B.

1967-01-01

Electronic band structure calculations phase of Ca, Sr and Ba over wide range of atomic volumes under pressure electronic band structure calculations for fcc phase of Ca, Sr and Ba over wide range of atomic volumes under pressure electronic band structure calculations for fcc phase of Ca, Sr and Ba over wide range of atomic volumes under pressure

A novel orange emissive phosphor SrWO4:Sm3+ for white light-emitting diodes

International Nuclear Information System (INIS)

Ju Zhenghua; Wei Ruiping; Ma Jingxin; Pang Chaoran; Liu Weisheng

2010-01-01

Research highlights: → A novel orange emissive phosphor SrWO 4 :Sm 3+ was firstly reported. → The optics properties of Sm 3+ -doped SrWO 4 phosphor were successfully discussed. → The temperature-dependent luminescence indicates the phosphor exhibits a small thermal-quenching property. → The phosphor is a potential candidate as orange-emitting component for white LED. - Abstract: A novel orange emissive phosphor, Sm 3+ -doped SrWO 4 , was synthesized by high temperature solid-state reaction in air atmosphere. The excitation spectra show that the phosphors can be efficiently excited by ultraviolet and near-ultraviolet light, the optimized concentration is 4 mol%. Three emission peaks locate at 562, 596 and 642 nm, corresponding to CIE chromaticity coordinates of (x = 0.54, y = 0.46), which indicates the orange light emitting. The decay curves are well fitted with triple-exponential decay models. The quantum yield of the Sr 0.96 Sm 0.04 WO 4 phosphor is about 70.65% under excitation of 377 nm. Furthermore, the temperature-dependent luminescence indicates the phosphor exhibits a small thermal-quenching property. So the phosphor is able to be applied to UV-LED chip-based white light-emitting diodes.

4f and 5d energy levels of the divalent and trivalent lanthanide ions in M2Si5N8 (M=Ca, Sr, Ba)

NARCIS (Netherlands)

Kate, ten O.M.; Zhang, Z.; Dorenbos, P.; Hintzen, H.T.J.M.; Kolk, van der E.

2013-01-01

Optical data of Sm, Tb and Yb doped Ca2Si5N8 and Sr2Si5N8 phosphors that have been prepared by solid-state synthesis, are presented. Together with luminescence data from literature on Ce3+ and Eu2+ doping in the M2Si5N8 (M=Ca, Sr, Ba) hosts, energy level schemes were constructed showing the energy

Photoluminescent properties of Sr2CeO4: Eu3+ and Sr2CeO4: Eu2+ phosphors suitable for near ultraviolet excitation

International Nuclear Information System (INIS)

Suresh, K.; Poornachandra Rao, N.V.; Murthy, K.V.R.

2014-01-01

Powder phosphors of 1 mol% Eu 3+ - and Eu 2+ -doped strontium cerium oxide (Sr 2 CeO 4 ) were synthesized by standard solid-state reaction method. Eu 3+ - and Eu 2+ -doped Sr 2 CeO 4 phosphors fired at 1100 ℃ for 2 h were analysed by X-ray diffraction (XRD) and photoluminescence (PL) techniques. The XRD patterns confirm that the obtained phosphors are a single phase of Sr 2 CeO 4 composed of orthorhombic structure. Room temperature PL excitation spectrum of air-heated Sr 2 CeO 4 : Eu phosphor has exhibited bands at 260, 280 and 350 nm. Whereas the excitation spectrum of Sr 2 CeO 4 : Eu phosphor heated under reducing (carbon) atmosphere exhibited single broadband range from 260 to 390 nm. The (PL) emission peaks of both the phosphors at 467 (blue), 537 (green) and 616 nm (red) generate white light under 260, 280 and 350 nm excitation wavelengths. The Commission International de l'Eclairage (CIE) colour coordinates conforms that these phosphors emitting white light. The results reveal that these phosphors are multifunctional phosphors which emit white light under these excitations that they could be used as white components for display and lamp devices and as well as possible good light-conversion phosphor LEDs under near-ultraviolet (nUV) chip. (author)

Photoluminescence in Sm3+ doped Ba2P2O7 phosphor prepared by solution combustion method

Science.gov (United States)

Ghawade, Sonal P.; Deshmukh, Kavita A.; Dhoble, S. J.; Deshmukh, Abhay D.

2018-05-01

In this paper, Sm3+ doped Ba2P2O7 phosphors were synthesized via a Solution combustion method. The crystal structure of the phosphor was characterized by XRD. Orange-red emission was observed from these phosphors under near-ultraviolet (UV) excitation at 404 nm. The luminescence properties of the obtained phosphors were characterized by different techniques. The Ba2P2O7:Sm3+ phosphor can be efficiently excited by near-UV and blue light, and their emission spectrum consists of three emission peaks, at 564, 602, and 646 nm, respectively. Based on the results, the as prepared Ba2P2O7:Sm3+ phosphors are promising orange-red-emitting phosphors exhibit great potential may be applicable as a spectral convertor in c-Si solar cell to enhance the efficiency of solar cell in future.

Luminescence properties of phosphate phosphor Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+}

Energy Technology Data Exchange (ETDEWEB)

Yang, Fu [College of Science, Hebei North University, Zhangjiakou 075000 (China); Liu, Yufeng, E-mail: liuyufeng4@126.com [State Key Lab of Power Systems, Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China); Tian, Xiaodong; Dong, Guoyi [College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Yu, Quanmao [Institute of Functional Materials, Jiangxi University of Finance & Economics, Nanchang 330013 (China)

2015-05-15

A series of reddish orange-emitting phosphate phosphors Ba{sub 3}Y{sub 1−x}(PO{sub 4}){sub 3}:xSm{sup 3+}(0.01≤x≤0.20) were synthesized by solid-state reaction. X-ray diffraction and photoluminescence spectra were utilized to characterize the structure and luminescence properties of as-synthesized phosphors. The optimized phosphors Ba{sub 3}Y{sub 0.95}(PO{sub 4}){sub 3}:0.05Sm{sup 3+} present several excitation bands from 300 to 500 nm, and exhibit intense reddish orange-emitting properties. The energy transfer type between Sm{sup 3+} ions was confirmed as d–d interaction by using Van Uitert model. The chromatic properties of the typical sample Ba{sub 3}Y(PO{sub 4}){sub 3}:0.05Sm{sup 3+} phosphor have been found to have chromaticity coordinates of (0.583, 0.405), which are located in reddish orange region under the excitation of 401 nm. These results indicated that Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+} phosphors have potential applications in the field of lighting and display due to their effective excitation in the near-ultraviolet range. - Graphical abstract: The color coordinates for 5 mol% Sm{sup 3+} doped Ba{sub 3}Y(PO{sub 4}){sub 3} phosphor were calculated to be (0.583, 0.405), which are located in reddish orange region under the excitation of 401 nm. The peaks of Ba{sub 3}Y{sub 0.95}(PO{sub 4}){sub 3}:0.05Sm{sup 3+} phosphor with the highest emission intensity at 600 nm are broader than those of Y{sub 2}O{sub 3}:Eu{sup 3+} and Y{sub 2}O{sub 2}S:Eu{sup 3+} phosphors. All these characteristics suggest that Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+} phosphors are suitable for near-UV (370–410 nm) excitation and can be applicable to near UV-based WLEDs. ▪ - Highlights: • Different concentration Sm{sup 3+}-doped Ba{sub 3}Y(PO{sub 4}){sub 3} phosphors were fabricated by solid state method. • The optimized phosphors present the several excitation bands from 300 to 500 nm. • The Ba{sub 3}Y(PO{sub 4}){sub 3}:Sm{sup 3+} shows bright reddish orange

A novel UV-emitting phosphor: LiSr4(BO3)3: Pb2+

International Nuclear Information System (INIS)

Pekgözlü, İlhan

2013-01-01

Pure and Pb 2+ doped LiSr 4 (BO 3 ) 3 materials were prepared by a solution combustion synthesis method. The phase analysis of all synthesized materials were determined using the powder XRD. The synthesized materials were investigated using spectrofluorometer at room temperature. The excitation and emission bands of LiSr 4 (BO 3 ) 3 : Pb 2+ were observed at 284 and 328 nm, respectively. The dependence of the emission intensity on the Pb 2+ concentration for the LiSr 4 (BO 3 ) 3 were studied in detail. It was observed that the concentration quenching of Pb 2+ in LiSr 4 (BO 3 ) 3 is 0.005 mol. The Stokes shifts of LiSr 4 (BO 3 ) 3 : Pb 2+ phosphor was calculated to be 4723 cm –1 . -- Highlights: • A novel UV-emitting phosphor: LiSr 4 (BO 3 ) 3 : Pb 2+ ” synthesized for the first time. • The emission band of LiSr 4 (BO 3 ) 3 : Pb 2+ was observed at 328 nm upon excitation with 284 nm. • LiSr 4 (BO 3 ) 3 : Pb 2+ is a good phosphor for broadband UV application

The system Ba(H2PO4)2-Sr(H2PO4)2-H3PO4(30%)-H2O at 25, 40 and 60 deg C

International Nuclear Information System (INIS)

Taranenko, N.P.; Serebrennikova, G.M.; Stepin, B.D.; Oboznenko, Yu.V.

1982-01-01

The system Ba(H 2 PO 4 ) 2 -Sr(H 2 PO 4 ) 2 -H 3 PO 4 (30%)-H 2 O (25 deg C) belongs to eutonic type systems. Solubility isotherms of salt components at 40 and 60 deg C are calculated. Polytherms (25-60 deg C) of solubility of monosubstituted barium and strontium phosphates in 30-60% H 3 PO 4 are obtained. The value of cocrystallization coefficient of Sr 2 + and Ba(H 2 PO 4 ) 2 Dsub(Sr)=0.042+-0.005 remains stable in the temperature range of 25-60 deg C and concentrations 30-60% phosphoric acid at initial content [Sr 2 + ]=1x10 - 2 mass%

Luminescent properties of near UV excitable Ba2ZnS3 : Mn red emitting phosphor blend for white LED and display applications

International Nuclear Information System (INIS)

Thiyagarajan, P; Kottaisamy, M; Rao, M S Ramachandra

2006-01-01

A bright red colour emitting Mn doped Ba 2 ZnS 3 phosphor was prepared by an ecologically acceptable carbothermal reduction method without an inert gas or hazardous gas (H 2 S) environment. The phosphor can be excited with UV wavelength radiation to realize emission in the visible range. X-ray diffraction studies confirm an orthorhombic structure with phase group, pnam. The photoluminescence (PL) emission spectrum shows a broad band with emission maximum at 625 nm under the host excitation of 358 nm, which lies in the near UV region. The concentration of Mn was varied from 0.0025 to 0.20 mole with respect to Zn and the optimum PL emission intensity was obtained at the concentration of 0.01 mole of Mn. The CIE (Commission Internationale de l'Eclairage) colour coordinates measurement (x = 0.654 and y = 0.321) shows that the primary emission is in the red region. The triband phosphors blend containing Sr 5 (PO 4 ) 3 Cl : Eu 2+ (blue), ZnS : Cu,Al (green) and Ba 2 ZnS 3 : Mn (red) shows white light emission under 365 nm excitation having CIE chromaticity (x = 0.292 and y = 0.251). Since phosphor excitation lies in the near UV excitable region, giving a bright red emission, it can be used for applications in near UV phosphor converted white LED lighting and display devices

Phosphors for solid-state lighting: New systems, deeper understanding

Science.gov (United States)

Denault, Kristin Ashley

We explore the structure-composition-property relationships in phosphor materials using a multitude of structural and optical characterization methods including high resolution synchrotron X-ray and neutron powder diffraction and total scattering, low-temperature heat capacity, temperature- and time-resolved photoluminescence, and density functional theory calculations. We describe the development of several new phosphor compositions and provide an in-depth description of the structural and optical properties. We show structural origins of improved thermal performance of photoluminescence and methods for determining structural rigidity in phosphor hosts that may lead to improved luminescent properties. New white light generation strategies are also explored. We begin by presenting the development of a green-yellow emitting oxyfluoride solid-solution phosphor Sr2Ba(AlO4F)1- x(SiO5)x:Ce3+. An examination of the host lattice, and the local structure around the Ce3+ activator ions points to how chemical substitutions play a crucial role in tuning the optical properties of the phosphor. The emission wavelength can be tuned from green to yellow by tuning the composition, x. Photoluminescent quantum yield is determined to be 70+/-5% for some of the examples in the series with excellent thermal properties. Phosphor-converted LED devices are fabricated using an InGaN LED and are shown to exhibit high color rendering white light. Next, we identify two new phosphor solid-solution systems, (Ba1- xSrx)9 Sc2Si6O24:Ce3+,Li+ and Ba9(Y1-ySc y)2Si6O24:Ce3+. The substitution of Sr for Ba in (Ba1-xSrx ) 9Sc2Si6O24:Ce 3+,Li + results in a decrease of the alkaline earth-oxygen bond distances at all three crystallographic sites, leading to changes in optical properties. The room temperature photoluminescent measurements show the structure has three excitation peaks corresponding to Ce3+ occupying the three independent alkaline earth sites. The emission of (Ba 1- xSrx) 9Sc2Si 6O24:Ce3

TL characterization of Ag co-doped SrSO{sub 4}:Eu phosphor for gamma dosimetry applications

Energy Technology Data Exchange (ETDEWEB)

Jayasudha, S., E-mail: jsnair.india@gmail.com [Mahatma Gandhi College, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Madhukumar, K.; Nair, C.M.K.; Nair, Resmi G.; Anandakumar, V.M. [Mahatma Gandhi College, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Elias, T.S. [State Institute of Cancer Research, Medical College P.O., Thiruvananthapuram 695011 (India); Rajesh, S. [Campus Universitario de Santiago, Aveiro (Portugal)

2017-04-15

High temperature thermoluminescence (TL) emissions and improvement in fading due to the co-doping ofr Ag in the SrSO{sub 4}:Eu phosphor synthesized through chemical precipitation technique when subjected to γ-excitation is discussed. The dopant concentrations were tuned for optimum TL sensitivity. Preliminary crystallographic and structural studies of the phosphors were done using PXRD, SEM, and TEM. The phosphor has a single phase orthorhombic lattice structure and the crystallites are found to be nanostructured. The presence of dopants in the host matrix is established through EDS and ICP-AES studies. The TL glow curve shows a single intense emission at 314 ├ó┬ü┬░C under γ- exposure of dose 1 Gy, which is given from a {sup 60}Co build-up. The dosimetric properties such as sensitivity, dose dependence, fading and reusability of SrSO{sub 4}:Eu,Ag phosphor were also studied. It is observed that co-doping with Ag improves the fading rate of the SrSO{sub 4}:Eu phosphor by about 5%. Even though the luminescence intensity is found to be less than that of SrSO{sub 4}:Eu phosphor, the Ag co-doped phosphor becomes significant owing to its improved fading rate and high temperature afterglow. The gamma sensitivity of the SrSO{sub 4}:Eu,Ag(0.5,0.5 mol%) phosphor is compared to that of the standard CaSO{sub 4}:Dy TLD phosphor. The TL kinetic parameters were calculated using IR, Chen's peak shape method and verified by the theoretical fit using GCD functions. - Highlights: • A High temperature TL emission is observed for the SrSO{sub 4}:Eu,Ag phosphor. • TL intensity is 10 times higher than that of standard CaSO{sub 4}:Dy. • Fading rate of SrSO{sub 4}:Eu phosphor is improved by 5% with Ag co-doping. • Linear dose response in the range 10mGy-10Gy. • t .

Crystal structure, thermally stability and photoluminescence properties of novel Sr10(PO4)6O:Eu2+ phosphors

International Nuclear Information System (INIS)

Guo, Qingfeng; Liao, Libing; Mei, Lefu; Liu, Haikun

2015-01-01

A series of novel luminescent phosphors Sr 10 (PO 4 ) 6 O:Eu 2+ with apatite structure were synthesized via a high temperature solid-state reaction. The phase structure, photoluminescence (PL) properties, the PL thermal stability, as well as the fluorescence decay curves of the samples were investigated to characterize the resulting samples, and the selected Sr 9.97 (PO 4 ) 6 O:0.03Eu 2+ phosphor exhibits strong thermal quenching resistance, retaining the luminance of 88.73% at 150 °C. The quenching concentration of Eu 2+ in Sr 10 (PO 4 ) 6 O was about 0.03 attributing to the dipole–quadrupole interaction. The Sr 10 (PO 4 ) 6 O:Eu 2+ phosphor exhibited a broad-band blue emission at 439 nm upon excitation at 346 nm. The results indicate that Sr 10 (PO 4 ) 6 O:Eu 2+ phosphors have potential applications as near UV-convertible phosphors for white-light UV LEDs. - Graphical abstract: Sr 10 (PO 4 ) 6 O:Eu 2+ phosphors have potential applications as near UV-convertible phosphors for white-light UV LEDs. - Highlights: • Sr 9.97 (PO 4 ) 6 O:0.03Eu 2+ phosphor exhibits strong thermal quenching resistance. • Two different Eu 2+ emission centers exists in Sr 10 (PO 4 ) 6 O. • The activation energy was also estimated for the Eu 2+ luminescence center

Enhanced luminescence in SrMgAl(x)O(17±δ):yMn4+ composite phosphors.

Science.gov (United States)

Cao, Renping; Sharafudeen, Kaniyarakkal N; Qiu, Jianrong

2014-01-03

Red-emitting SrMgAlxO17±δ:yMn(4+) composite phosphors (x=10-100; y=0.05-4.0 mol%) are synthesized by solid-state reaction method in air. Addition of Al2O3 leads to the formation of two concomitant phases, i.e., SrMgAl10O17 and Al2O3 phases in the composite phosphor. Red emission from Mn(4+) ions in the composite phosphors is greatly enhanced due to multiple scattering and absorption of excitation light between SrMgAl10O17 and Al2O3 phases. SrMgAlxO17±δ:yMn(4+) composite phosphors would be a promising candidate as red phosphor in the application of a 397 nm near UV-based W-LED. Copyright © 2013 Elsevier B.V. All rights reserved.

BaFCl:Eu2+, a new phosphor for X-ray-intensifying screens

International Nuclear Information System (INIS)

Stevels, A.L.N.; Pingault, F.

1975-01-01

A number of phosphors for X-ray-intensifying screens have been evaluated by calculating figures of merit. On use in combination with standard (''blue''-sensitive) X-ray film, BaFCl:Eu 2+ and BaFBr:Eu 2+ give better performance than the traditional CaWO 4 and more recently developed UV or blue-emitting materials (e.g., sulphates and y-oxysulphides). The calculated figures of merit of BaFCl:Eu 2+ or BaFBr:Eu 2+ /standard-film combinations are comparable to those of Gd 2 O 2 S:Tb/green-sensitive X-ray film systems. The preparation of optimal fluorohalide:Eu 2+ phosphors involves proper formation of the host lattice, complete reduction of Eu 3+ ions as well as elimination of afterglow. Measurements on powders and experimental screens indicate that by using BaFCl:Eu 2+ screens in radiography, important dose reductions can be achieved without the necessity of using other than standard (''blue''-sensitive) X-ray films

Design, synthesis and luminescence properties of Ba2 YB2 O6 Cl- and Ba2 YB2 O6 F-based phosphors.

Science.gov (United States)

Chen, Wanping; Yang, Xin; Liu, Yan; Dai, Xiaoyan

2015-05-01

Using a high-temperature solid-state reaction, the chlorine in Ba2 YB2 O6 Cl is gradually replaced by F, and a new compound with the nominal chemical formula Ba2 YB2 O6 F and two phosphors doped with Ce(3+) and Eu(3+) , respectively, are obtained. X-Ray diffraction and photoluminescence spectroscopy are used to characterize the as-synthesized samples. The as-synthesized Ba2 YB2 O6 Cl exhibits bright blue emission in the spectral range ~ 330-410 nm with a maximum around 363 nm under X-ray or UV excitation. Ba2 YB2 O6 F:0.01Ce(3+) exhibits blue emission in the range ~ 340-570 nm with a maximum around 383 nm. Ba2 YB2 O6 F:0.01Eu(3+) exhibits a predominantly (5) D0 -(7)  F2 emission (~610 nm) and the relative intensities of the (5) D0 -(7)  F0,1,2 emissions are tunable under different wavelength UV excitation. The luminescence behaviors of the two phosphors are explained simply in terms of the host composition and site occupancy probability of Ce(3+) and Eu(3+) , respectively. The results indicate that these phosphors have potential application as a blue phosphor or as a red phosphor. Copyright © 2014 John Wiley & Sons, Ltd.

Refinement of crystal structures of CaHCl, SrHCl, BaHCl, BaHBr, and BaHI

International Nuclear Information System (INIS)

Beck, H.P.; Limmer, A.

1983-01-01

The structures of CaHCl, SrHCl, BaHBr, BaHCl, and BaHI have been refined using single crystal data. The comparison of the parameters with the corresponding data of isotypic fluorohalide compounds gives a valuable insight into the bonding interactions in this structure type. (author)

Refinement of crystal structures of CaHCl, SrHCl, BaHCl, BaHBr, and BaHI

Energy Technology Data Exchange (ETDEWEB)

Beck, H.P.; Limmer, A. (Erlangen-Nuernberg Univ., Erlangen (Germany, F.R.). Inst. fuer Anorganische Chemie)

1983-07-01

The structures of CaHCl, SrHCl, BaHBr, BaHCl, and BaHI have been refined using single crystal data. The comparison of the parameters with the corresponding data of isotypic fluorohalide compounds gives a valuable insight into the bonding interactions in this structure type.

TL dosimetric characterization of gamma irradiated SrSO{sub 4}:Eu phosphors

Energy Technology Data Exchange (ETDEWEB)

Jayasudha, S., E-mail: jsnair.india@gmail.com [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Madhukumar, K.; Nair, C.M.K.; Nair, Resmi G. [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Rajesh, S. [Department of Materials & Ceramic Engineering, University of Aveiro, Aveiro 3810-193 (Portugal); Elias, T.S. [State Institute of Cancer Research, Medical College P.O., Thiruvananthapuram 695011 (India); Anandakumar, V.M. [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India); State Institute of Cancer Research, Medical College P.O., Thiruvananthapuram 695011 (India); Department of Materials & Ceramic Engineering, University of Aveiro, Aveiro 3810-193 (Portugal); Gopakumar, N. [Mahatma Gandhi College, Kesavadasapuram, Pattom Palace P.O., Thiruvananthapuram 695004 (India)

2017-03-15

Thermoluminescence (TL) characteristics of SrSO{sub 4}:Eu nanostructured phosphor under gamma excitation has been studied and their suitability for environmental radiation dosimetry applications is discussed. The dopant level is tuned for optimum TL response. The effect of radiation dose and heating rate were investigated. The phosphor preserves linearity in the low dose region, 0.1 Gy to 20 Gy. PL studies of irradiated and un-irradiated phosphors reveal that the dopant Eu exists in divalent state and are the luminescence emission centres in the material. The fading properties of SrSO{sub 4}:Eu phosphor are observed to be better than that of the commercial dosimeters TLD-200 and TLD-400. The kinetic parameters are calculated using Chen's method and initial rise method and verified by Computerized Glow curve Deconvolution (CGCD). The sensitivity of the synthesized phosphor is found to be very high when compared with that of the commercial standard dosimeter CaSO{sub 4}:Dy. The phosphor is found to be stable for short term radiation monitoring.

Improved photoluminescence properties of a new green SrB2O4:Tb3+ phosphor by charge compensation

International Nuclear Information System (INIS)

Wu, Zhan-Chao; Wang, Ping; Liu, Jie; Li, Chao; Zhou, Wen-Hui; Kuang, Shao-Ping

2012-01-01

Highlights: ► New green-emitting SrB 2 O 4 :Tb 3+ phosphor was synthesized by solid-state reaction. ► Li + , Na + , and K + can all increase luminescent intensity of SrB 2 O 4 :Tb 3+ . ► Na + is the optimal charge compensator among Li + , Na + and K + . ► SrB 2 O 4 :Tb 3+ is a promising green phosphor for fabricating WLED. -- Abstract: A new green-emitting SrB 2 O 4 :Tb 3+ phosphor was synthesized by solid-state reaction. X-ray powder diffraction (XRD) analysis confirmed all the samples with orthorhombic formation of SrB 2 O 4 . The excitation spectra indicate the phosphor can be effectively excited by near ultraviolet (NUV) light, making it attractive as conversion phosphor for LED applications. The phosphor exhibits a bright green emission with the highest photoluminescence (PL) intensity at 544 nm excited by 378 nm light. The critical quenching concentration of Tb 3+ in SrB 2 O 4 :Tb 3+ is about 10 mol%. The effects of charge compensators (Li + , Na + , and K + ) on photoluminescence of SrB 2 O 4 :Tb 3+ were also studied. The results show that the emission intensity can be improved by all the three charge compensators and Na + is the optimal one for SrB 2 O 4 :Tb 3+ . All properties show that the phosphor is a promising green phosphor pumped by NUV InGaN chip for fabricating white light-emitting diodes (WLEDs).

Structural and optical properties of (Sr,Ba)2SiO4:Eu2+ thin films grown by magnetron sputtering

International Nuclear Information System (INIS)

Li, Leliang; Zheng, Jun; Zuo, Yuhua; Cheng, Buwen; Wang, Qiming

2014-01-01

(Sr,Ba) 2 SiO 4 :Eu 2+ thin films were deposited on Si at different substrate temperatures by magnetron sputtering. The morphology and crystalline phases of the films were studied by scanning electron microscopy (SEM) and X-ray diffraction (XRD) measurements, respectively. The silicate crystal phase was presented when films were annealed above 900 °C and the annealing temperature had great impact on the film morphology. The samples annealed at 1000 °C in a non-reducing atmosphere for 30 s show intense room temperature Eu 2+ emission. These findings may open a promising way to prepare efficient phosphor thin films for on-chip light emitting diodes application. - Highlights: • The (Sr, Ba) 2 SiO 4 :Eu 2+ films are fabricated by magnetron sputtering. • A very strong RT PL emission at 540 nm is achieved. • The morphology and optical properties dependent on temperature are studied

The feasibility of boron containing phosphors in thermal neutron image plates, in particular the systems M sub 2 B sub 5 O sub 9 X : Eu sup 2 sup + (M=Ca, Sr, Ba; X=Cl, Br) Part II: experimental results

CERN Document Server

Knitel, M J; Dorenbos, P; Eijk, C W E; Berezovskaya, I V; Dotsenko, V

2000-01-01

The storage phosphor properties of the compounds M sub 2 B sub 5 O sub 9 X : Eu sup 2 sup + (M=Ca, Sr, Ba; X=Cl, Br) have been studied. The best compounds, Sr sub 2 B sub 5 O sub 9 Br : Eu sup 2 sup + and Ca sub 2 B sub 5 O sub 9 Br : Eu sup 2 sup + , show a photostimulated luminescence yield of, respectively, 21 and 14 photons per incident thermal neutron. They contain natural boron. With these yields, image plates with detective quantum efficiency values of more than 40% are envisaged when using enriched sup 1 sup 0 B, but the stimulation energy at 633 nm is too high.

Study of effect of co-doping on CIE coordinates of strontium cerium oxide phosphor (Sr_2CeO_4)

International Nuclear Information System (INIS)

Zambare, Pradip Z.; Ahirrao, P.B.; Chaudhari, D.B.; Zambare, A.P.; Mahajan, O.H.

2016-01-01

The phosphors Sr_2CeO_4 doped europium and gadolinium were synthesized by modified solid state diffusion method. From emission spectra, the CIE coordinates (x, y) of x% Eu"3"+ and 0.5 %Gd"3"+ doped Sr_2CeO_4 phosphors was calculated. In present paper, we investigate luminescence properties and colorimetric study of Sr_2CeO_4 doped 0.5% Gd"3"+, x% Eu"3"+. The phosphors Sr_2CeO_4 doped europium and gadolinium were successfully synthesized by modified solid state diffusion method. X-ray diffraction (XRD) profile confirms the orthorhombic nature of Eu"3"+ and 0.5% Gd"3"+ doped Sr_2CeO_4 phosphors. In addition, scanning electron Microscopy (SEM), Fourier-Transformation IR spectroscopy (FTIR), was also used to study the synthesized phosphors

Red, Green, and Blue Photoluminescence of Ba2SiO4:M (M = Eu3+, Eu2+, Sr2+ Nanophosphors

Directory of Open Access Journals (Sweden)

Claudia Wickleder

2013-07-01

Full Text Available Divalent europium doped barium orthosilicate is a very important phosphor for the production of light emitting diodes (LEDs, generally associated to the green emission color of micron-sized crystals synthesized by means of solid-state reactions. This work presents the combustion synthesis as an energy and time-saving preparation method for very small nano-sized Ba2SiO4 particles, flexibly doped to acquire different emission energies. The size of the resulting spherical nanoparticles (NPs of the green emitting Ba2SiO4:Eu2+ was estimated to about 35 nm applying the Scherrer equation and further characterized with aid of atomic force microscopy (AFM as well as scanning electron microscopy (SEM. This phosphor is able to build homogeneous luminescent suspensions and was successfully down-sized without changing the optical properties in comparison to the bulk phosphors. Besides the X-ray diffraction (XRD analysis and the different types of microscopy, the samples were characterized by luminescence spectroscopy. Undoped Ba2SiO4 NPs are not luminescent, but show characteristic red emission of the 5D0 → 7FJ (J = 0–4 electronic transitions when doped with Eu3+ ions. Moreover, these orthosilicate nanoparticles generate blue light at low temperatures due to impurity-trapped excitons, introduced by the partial substitution of the Ba2+ with Sr2+ ions in the Ba2SiO4 lattice causing a substantial distortion. A model for the temperature behavior of the defect luminescence as well as for their nature is provided, based on temperature-dependent luminescence spectra and lifetime measurements.

Luminescence behaviors of Eu- and Dy-codoped alkaline earth metal aluminate phosphors through potassium carbonate coprecipitation

Energy Technology Data Exchange (ETDEWEB)

Liang, Chen-Jui, E-mail: cjliang@fcu.edu.tw; Siao, Hao-Yi

2016-07-01

An electronic energy mechanism of activator and sensitizer was established to describe the luminescence behaviors of Eu- and Dy-codoped M(II)Al{sub 2}O{sub 4} (M(II) = Ba, Sr, Ca, Mg) phosphors through potassium carbonate coprecipitation. Experimental results demonstrated that the prepared phosphors exhibited superior crystallinity at a temperature lower than 950 °C. The phosphors are ordered according to emission intensity as follows Ca- > Ba- > Sr- > Mg-containing phosphors. The energy level for Eu{sup 2+} 4f{sup 6}5d{sup 1} → 4f{sup 7}, Eu{sup 3+4}D{sub 0} → {sup 7}F, and Dy{sup 3+4}F{sub 9/2} → {sup 6}H transitions and the effects of nephelauxetic and crystal field in Ba-, Sr-, and Ca-containing phosphors were discussed. The energy gap, (hv){sub em}, between 5d and 4f of Eu{sup 2+} ion is strongly affected by host composition, crystal field strength, and nephelauxetic effect. The infrared emission of 4f{sub 9/2} → 6h for Dy{sup 3+} is merely depend on the transfer of energy from Eu{sup 2+} upon excited. Ca-containing phosphor with maximum (hv){sub em} is attributed to the lowest bond length of Ca−O and highest ionization potential of Ca{sup 2+} ion, which leads to the effects of crystal field and nephelauxetic greater than that in the other phosphors. - Highlights: • The list of the collected figure captions: • Develop a new coprecipitation method to prepare high efficiency phosphors. • Obtain superior crystallinity with lower calcination temperature. • Luminescence behavior of Eu- and Dy-codoped on aluminate phosphors is discussed. • Investigate the effects of alkaline earth metal containing on crystal field and nephelauxetic.

Effect of local environment on crossluminescence kinetics in SrF{sub 2}:Ba and CaF{sub 2}:Ba solid solutions

Energy Technology Data Exchange (ETDEWEB)

Terekhin, M.A. [P.N. Lebedev Physical Institute, Leninskij Prospekt 53, 119991 Moscow (Russian Federation); Makhov, V.N., E-mail: makhov@sci.lebedev.ru [P.N. Lebedev Physical Institute, Leninskij Prospekt 53, 119991 Moscow (Russian Federation); Lebedev, A.I.; Sluchinskaya, I.A. [Lomonosov Moscow State University, Moscow 119991 (Russian Federation)

2015-10-15

Spectral and kinetic properties of extrinsic crossluminescence (CL) in SrF{sub 2}:Ba (1%) and CaF{sub 2}:Ba (1%) are compared with those of intrinsic CL in BaF{sub 2} and are analyzed taking into account EXAFS data obtained at the Ba L{sub III} edge and results of first-principles calculations. The CL decay time was revealed to be longer in SrF{sub 2}:Ba and CaF{sub 2}:Ba compared to BaF{sub 2}. This fact contradicts the expected acceleration of luminescence decay which could result from an increased overlap of wave functions in solid solutions due to shortening of the Ba-F distance obtained in both EXAFS measurements and first-principles calculations. This discrepancy is explained by the effect of migration and subsequent non-radiative decay of the Ba (5p) core holes in BaF{sub 2} and by decreasing of the probability of optical transitions between Ba (5p) states and the valence band in SrF{sub 2}:Ba and CaF{sub 2}:Ba predicted by first-principles calculations. - Highlights: • The crossluminescence kinetics in SrF{sub 2}:Ba and CaF{sub 2}:Ba is slower than in BaF{sub 2}. • Ba{sup 2+} ions substitute for host Ca{sup 2+}(Sr{sup 2+}) ions in the on-center positions. • The nearest Ba-F distances in SrF{sub 2}:Ba and CaF{sub 2}:Ba are shorter than in BaF{sub 2}. • EXAFS data and first-principles calculations of the local structure agree well. • First-principles calculations explain slower luminescence decay in solid solutions.

[Effect of charge compensation on emission spectrum of Sr2SiO4 : Dy3+ phosphor].

Science.gov (United States)

Li, Pan-Lai; Wang, Zhi-Jun; Yang, Zhi-Ping; Guo, Qing-Lin

2009-01-01

The Sr2SiO4 : Dy3+ phosphor was synthesized by the high temperature solid-state reaction method in air. Dy2O3 (99.9%), SiO2 (99.9%), SrCO3 (99.9%), Li2CO3 (99.9%), Na2CO3 (99.9%) and K2CO3 (99.9%) were used as starting materials, and the Dy3+ doping concentration was 2 mol%. The emission spectrum was measured by a SPEX1404 spectrophotometer, and all the characterization of the phosphors was conducted at room temperature. The emission spectrum of Sr2 SiO4 : Dy3+ phosphor showed several bands centered at 486, 575 and 665 nm under the 365 nm excitation. The effect of Li+, Na+ and K+ on the emission spectra of Sr2SiO4 : Dy3+ phosphor was studied. The results show that the location of the emission spectrum of Sr2SiO4 : Dy3+ phosphor was not influenced by Li+, Na+ and K+. However, the emission spectrum intensity was greatly influenced by Li+, Na+ and K+, and the evolvement trend was monotone with different charge compensation, i. e. the emission spectrum intensity of Sr2SiO4 : Dy3+ phosphor firstly increased with increasing Li+ concentration, then decreased. However the charge compensation concentration corresponding to the maximum emission intensity was different with different charge compensation, and the concentration is 4, 3 and 3 mol% corresponding to Li+, Na+ and K+, respectively. And the theoretical reason for the above results was analyzed.

Photoionization behavior of Eu2+-doped BaMgSiO4 long-persisting phosphor upon UV irradiation

International Nuclear Information System (INIS)

Li, Y.; Wang, Y.; Gong, Y.; Xu, X.; Zhang, F.

2011-01-01

Highlights: → Photoionization behavior of BaMgSiO 4 :Eu 2+ long persistent phosphor upon UV irradiation. → Green phosphorescence was obtained from BaMgSiO 4 :Eu 2+ . → The ionization of Eu 2+ to Eu 3+ was observed in BaMgSiO 4 :Eu 2+ . → The photogenerated Eu 3+ cannot change back to its divalent state at room temperature. → The phosphorescence is associated with the formation forming Eu 3+ -e - pairs. - Abstract: The fluorescence, phosphorescence and thermoluminescence properties of Eu-doped BaMgSiO 4 phosphors sintered in air and in a reducing atmosphere were investigated. Phosphorescence of phosphor sintered in a reducing atmosphere can last for 1.5 h at a recognizable intensity level, whereas phosphorescence of air-sintered phosphor can only persist for 6 min. In addition, a distinction between the shape of the fluorescence spectrum and its corresponding phosphorescence spectrum is observed in the former case. Ionization of Eu 2+ to Eu 3+ upon UV irradiation is observed in the phosphor prepared in a reducing atmosphere, but there is no indication that the photogenerated Eu 3+ cannot change back to its divalent state at room temperature after the excitation source is switched off. In addition, phosphor sintered in a reducing atmosphere shows photochromism upon UV irradiation. No such photoionization and photochromism behavior is observed for the air-sintered phosphor. A possible Eu 2+ photoionization mechanism is constructed on the basis of these experimental observations. The photoionization mechanism presented can also successfully explain the fluorescence and phosphorescence behavior of Eu in BaMgSiO 4 .

Investigation of thermoluminescence and electron-vibrational interaction parameters in SrAl2O4:Eu2+, Dy3+ phosphors

International Nuclear Information System (INIS)

Pardhi, Shilpa A.; Nair, Govind B.; Sharma, Ravi; Dhoble, S.J.

2017-01-01

Combustion synthesis method was employed for the synthesis of green-emitting monoclinic SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors. The phase-purity of the prepared phosphors were examined using X-ray diffraction (XRD). The prepared phosphors exhibited green light emission with the peak centred at 510 nm, under 350 nm UV excitation. The excitation and emission spectra were analysed and the parameters of electron-vibrational interaction (EVI), such as the Huang–Rhys factor, effective phonon energy and zero-phonon line position were estimated using the spectrum fitting method. Thermoluminescence (TL) behaviour of the as-prepared phosphors were analysed for UV and 137 Cs γ-ray source irradiation. TL glow curves for UV-irradiated SrAl 2 O 4 :Eu 2+ , Dy 3+ phosphors were analysed. - Highlights: • Photoluminescence and thermoluminescence properties of SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors were analysed. • Electron-vibrational interaction (EVI) parameters of SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors were determined. • The phosphors are found to exhibit green light emission.

New NaSrPO4:Sm phosphor as orange-red emitting material

Indian Academy of Sciences (India)

Because NaSr1−xPO4:xSm3+ phosphor features a high colour-rendering index and chemical stability, it is potentially ... use blue LED chips (GaN or InGaN) with a yellow phosphor ... excitation by doping Sm3+ rare earth ions into a suitable.

Blue–green afterglow of BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Zhai, Bao-gai [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China); Ma, Qing-lan [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China); School of Electronics and Information, Nantong University, Jiangsu 226019 (China); Xiong, Rui [School of Physics and Technology, Wuhan University, Hubei 430072 (China); Li, Xiazhang [Analysis and Testing Center, Changzhou University, Jiangsu 213164 (China); Huang, Yuan Ming, E-mail: dongshanisland@126.com [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China)

2016-03-15

Highlights: • Afterglow can be achieved when Eu{sup 2+} is absent in the DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. • The afterglow of DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors is discernible to naked eyes for minutes. • Dy{sup 3+} introduced trap centers are believed to be responsible for the afterglow. - Abstract: Dy{sup 3+} doped barium aluminate (BaAl{sub 2}O{sub 4}:Dy{sup 3+}) phosphors were prepared via the sol–gel combustion route at the ignition temperature of 600 °C. The phosphors were characterized with X-ray diffractometry, scanning electron microscopy, transmission electron microscopy, photoluminescence spectroscopy, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Regardless of the absence of Eu{sup 2+} luminescent centers, broadband blue–green afterglow with its peak at about 490 nm was recorded in the BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. The decay profile of the blue–green afterglow can be best fitted into a two-component exponential function with the two lifetime decay constants to be 8.81 and 45.25 s, respectively. The observation of blue–green afterglow from BaAl{sub 2}O{sub 4}:Dy{sup 3+} in the absence of Eu{sup 2+} provides unique opportunity in unveiling the afterglow mechanisms of rare-earth doped alkaline-metal aluminates. Possible mechanisms on the blue–green afterglow in BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors are discussed in terms of the Dy{sup 3+} ions introduced trap centers as well as luminescent centers in the crystal lattice.

Photoluminescence properties of X5SiO4Cl6:Tb (X = Sr, Ba) green ...

Indian Academy of Sciences (India)

attracted more attention due to their potential applications ... materials were thoroughly mixed and ground in an agate mortar. ... Figure 2. Excitation spectra of Ba5SiO4Cl6:Tb3+ phosphor. spectrum of Tb3+ singly doped phosphor Ba5SiO4Cl6,.

Luminescence in Eu2+ and Ce3+ doped SrCaP2O7 phosphors

Directory of Open Access Journals (Sweden)

K.N. Shinde

Full Text Available Eu2+ and Ce3+ doped SrCaP2O7 has been achieved by modified solid state diffusion in reducing atmosphere. The prepared phosphor powders have been identified by their characteristic X-ray diffraction patterns. The mixed phases of α-Sr2P2O7 type with orthorhombic and α-Ca2P2O7 type with monoclinic form were investigated. Its excitation wavelength ranging from 250 to 430 nm fits well with the characteristic emission of UV light-emitting diode (LED. The excitation and emission spectra indicate that these phosphors can be effectively excited by the near-UV light, and emits blue (visible range due to 4f7 → 4f65d1 transition of Eu2+ particularly, SrCaP2O7: Eu2+ whereas, photoluminescence excitation spectrum measurements of Ce3+ activated SrCaP2O7 shows that the phosphor can be efficiently excited by UV–Vis light from 280 to 310 nm to realize emission in the near visible range due to the 5d–4f transition of Ce3+ ions which is applicable for scintillation purpose. The impacts of doping of divalent europium and trivalent cerium on photoluminescence properties on SrCaP2O7 pyrophosphate phosphors were investigated and I propose a feasible interpretation. Keywords: Phosphor, Luminescence, XRD, LED, FTIR

Isothermal cross-sections of Sr-Al-Ge and Ba-Al-Ge systems at 673 K

International Nuclear Information System (INIS)

Kutsenok, N.L.; Yanson, T.I.

1987-01-01

X-ray and microstructural analyses are used to study phase equilibria in Sr-Al-Ge and Ba-Al-Ge systems. Existence of SrAl 2 Ge 2 , Sr(Al, Ge) 2 Ba(Al, Ge) 2 , Sr 3 Al 2 Ge 2 , Ba 3 Al 2 Ge 2 ternary compounds is confirmed, a new BaGe 4 binary compound and also new ternary compounds of approximate composition Sr 57 Al 30 Ge 13 and Ba 20 Al 40 Ge 40 , which crystal structure is unknown, are detected. Aluminium solubility in SrAl 4 and BaAl 4 binary compounds (0.05 atomic fraction) is determined. Ba(Al, Ge) 2 compound homogeneity region is defined more exactly (aluminium content varies from 0.27 to 0.51 at. fractions)

Bluish-green color emitting Ba2Si3O8:Eu2+ ceramic phosphors for white light-emitting diodes.

Science.gov (United States)

Xiao, F; Xue, Y N; Zhang, Q Y

2009-10-15

This paper reports on the structural and optical properties of Eu(2+) activated Ba(2)Si(3)O(8) ceramic phosphors synthesized by a sol-gel method. The ceramic phosphors have been characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) and fluorescence measurements. The structural characterization results suggest that the as-prepared phosphors are of single phase monoclinic Ba(2)Si(3)O(8) with rod-like morphology. A broad excitation band ranging from 300 to 410 nm matches well with the ultraviolet (UV) radiation of light-emitting diodes (LEDs). Upon 380 nm UV light excitation, these phosphors emit bluish-green emission centered at 500 nm with color coordination (x=0.25, y=0.40). All the obtained results indicate that the Ba(2)Si(3)O(8):Eu(2+) ceramic phosphors are promising bluish-green candidates for the phosphor-converted white LEDs.

Adsorption removal of Sr by Barium impregnated 4A Zeolite(BaA) from high radioactive seawater waste

Energy Technology Data Exchange (ETDEWEB)

Lee, Eil Hee; Lee, Keun Young; Kim, Kwang Wook; Kim, Ik Soo; Chung, Dong Yong; Moon, Jei Kwon; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-06-15

This study investigated the removal of Sr, which was one of the high radioactive nuclides, by adsorption with Barium (Ba) impregnated 4A zeolite (BaA) from high-radioactive seawater waste (HSW). Adsorption of Sr by BaA (BaA-Sr), in the impregnated Ba concentration of above 20.2wt%, was decreased by increasing the impregnated Ba concentration, and the impregnated Ba concentration was suitable at 20.2wt%. The BaA-Sr adsorption was added to the co-precipitation of Sr with BaSO4 precipitation in the adsorption of Sr by 4A (4A-Sr) within BaA. Thus, it was possible to remove Sr more than 99% at m/V (adsorbent weight/solution volume)=5 g/L for BaA and m/V >20 g/L for 4A, respectively, in the Sr concentration of less than 0.2 mg/L (actual concentration level of Sr in HSW). It shows that BaA-Sr adsorption is better than 4A-Sr adsorption in for the removal capacity of Sr per unit gram of adsorbent, and the reduction of the secondary solid waste generation (spent adsorbent etc.). Also, BaA-Sr adsorption was more excellent removal capacity of Sr in the seawater waste than distilled water. Therefore, it seems to be effective for the direct removal of Sr from HSW. On the other hand, the adsorption of Cs by BaA (BaA-Cs) was mainly performed by 4A within BaA. Accordingly, it seems to be little effect of impregnated Ba into BaA. Meanwhile, BaA-Sr adsorption kinetics could be expressed the pseudosecond order rate equation. By increasing the initial Sr concentrations and the ratios of V/m, the adsorption rate constants (k2) were decreased, but the equilibrium adsorption capacities (qe) were increasing. However, with increasing the temperature of solution, k2 was conversely increased, and qe was decreased. The activation energy of BaA-Sr adsorption was 38 kJ/mol. Thus, the chemical adsorption seems to be dominant rather than physical adsorption, although it is not a chemisorption with strong bonding form.

Luminescence properties and energy transfer investigations of Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphors

International Nuclear Information System (INIS)

Yang, Zaifa; Xu, Denghui; Sun, Jiayue; Du, Jiangnan; Gao, Xuedong

2016-01-01

Highlights: • A phosphor Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ for UV-based white LEDs was firstly synthesized successfully. • The phase structure and photoluminescence properties of samples were studied in detail. • The energy transfer process from Ce"3"+ to Tb"3"+ ions was illustrated in detail. • Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor has potential applications as an UV-convertible phosphor for white light emitting diodes. - Abstract: A series of Ce"3"+ or Tb"3"+ doped and Ce"3"+/Tb"3"+ co-doped Sr_3Lu(PO_4)_3 phosphors were prepared via the conventional high temperature solid-state reaction. The phase structure, photoluminescence and energy transfer properties of samples were studied in detail. The optimal proportion of Ce"3"+ single doping is 4 mol% with maximal fluorescence intensity. The Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor shows both a blue emission (428 nm) from Ce"3"+ and a yellowish-green emission (545 nm) from Tb"3"+ with considerable intensity under ultraviolet (UV) excitation (268 nm). The energy transfer from Ce"3"+ to Tb"3"+ ions takes place in the Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor on the basis of the analysis of the luminescence spectra. The energy transfer mechanism from Ce"3"+ to Tb"3"+ ions was proved to be dipole–dipole interaction. The energy transfer behaviors in Sr_3Lu(PO_4)_3:Ce"3"+, Tb"3"+ phosphor is also investigated by the lifetime measurement. The results show that this phosphor has potential applications for UV white-light LEDs.

Combustion synthesis of Eu and Dy activated Sr3(VO4)2 phosphor ...

Indian Academy of Sciences (India)

phosphor as well as Sr3(VO4)2:Dy is blue and yellow emitting phosphor for solid state lighting i.e. white LEDs. The ... 2004; Pang et al 2004) doped with rare earth has expanded ... controlled since the LED light output (intensity and colour).

High field-effect mobility at the (Sr,Ba)SnO{sub 3}/BaSnO{sub 3} interface

Energy Technology Data Exchange (ETDEWEB)

Fujiwara, Kohei, E-mail: kfujiwara@imr.tohoku.ac.jp; Nishihara, Kazuki; Shiogai, Junichi; Tsukazaki, Atsushi [Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)

2016-08-15

A perovskite oxide, BaSnO{sub 3}, has been classified as one of transparent conducting materials with high electron mobility, and its application for field-effect transistors has been the focus of recent research. Here we report transistor operation in BaSnO{sub 3}-based heterostructures with atomically smooth surfaces, fabricated on SrTiO{sub 3} substrates by the (Sr,Ba)SnO{sub 3} buffer technique. Indeed, modulation of band profiles at the channel interfaces with the insertion of wide bandgap (Sr,Ba)SnO{sub 3} as a barrier layer results in a significant improvement of field-effect mobility, implying effective carrier doping at the regulated heterointerface. These results provide an important step towards realization of high-performance BaSnO{sub 3}-based field-effect transistors.

Synthesis, structural and luminescent aspect of Tb3+ doped Sr2SnO4 phosphor

International Nuclear Information System (INIS)

Taikar, Deepak R.

2016-01-01

A novel green emitting, Tb 3+ doped Sr 2 SnO 4 phosphor was synthesized by the co-precipitation method and its photoluminescence characterization was performed. Sr 2 SnO 4 has an ordered tetragonal K 2 NiF 4 -type structure with space group I4/mmm. The structure of Sr 2 SnO 4 consists of SnO 6 octahedra. From the structure of Sr 2 SnO 4 , it was observed that the sites of Sn 4+ ions have inverse symmetry while the Sr 2+ ions have the low symmetry. X-ray powder diffraction (XRD) analysis confirmed the formation of Sr 2 SnO 4 :Tb 3+ . Photoluminescence measurements showed that the phosphor exhibited bright green emission at about 543 nm attributed to 5 D 4 à 7 F 5 transition of Tb 3+ ion under UV excitation. The emission spectra did not exhibit conventional blue emission peaks of Tb 3+ ions due to 5 D 3 → 7 F J transitions in the spectral region 350-470 nm. The excitation spectra indicate that this compound may be useful as a lamp phosphor. (author)

Eu and Sr2CeO4 : Eu phosphors suitable for near ultraviolet excitation

Indian Academy of Sciences (India)

Administrator

The study on white light phosphors suitable for near- ultraviolet (nUV) ... Rare earth ion-doped phosphors have been used in varied fields ... practical applications. .... by naked eyes. ... induced by Sr2CeO4 host matrix (Arunachalam Laxmanan.

Synthesis and luminescence properties of novel Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Xu, Qiguang; Sun, Jiayue, E-mail: Jiayue_sun@126.com; Cui, Dianpeng; Di, Qiumei; Zeng, Junhui

2015-02-15

Sr{sub 3}(Gd{sub 1−x}Dy{sub x})(PO{sub 4}){sub 3} phosphors for white light-emitting diodes (w-LEDs) were prepared by the conventional solid-state reaction. X-ray diffraction (XRD) and photoluminescence spectra were utilized to characterize the structure and luminescence properties of the as-synthesized phosphors. Luminescence properties shows that the phosphor can be efficiently excited by the ultraviolet visible light in the region from 300 to 450 nm, and it exhibits blue (483 nm) and yellow (575 nm) emission corresponding to {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} transition and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} transition, respectively. It has been found that concentration quenching occurs via dipole–dipole interaction according to Dexter's theory. The temperature dependence of photoluminescence properties is investigated from 25 to 250 °C and the prepared Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors show good thermal quenching properties. - Highlights: • Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors were synthesized by a solid-state reaction method. • The phosphor could be efficiently excited by the UV–vis light region from 300 to 450 nm. • Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors exhibited blue (483 nm) and yellow (575 nm) emission. • The Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors concentration quenching occurred as a result of dipole–dipole interaction. • Sr{sub 3}Gd(PO{sub 4}){sub 3}:Dy{sup 3+} phosphors showed good thermal quenching properties.

Mechanoluminescence, photoluminescence and thermoluminescence studies of SrZrO3:Ce phosphor

Directory of Open Access Journals (Sweden)

Neha Tiwari

2015-01-01

Full Text Available The present paper reports the synthesis and characterization, photoluminescence thermoluminescence and mechanoluminescence studies of Ce3+ doped SrZrO3 phosphors. The effects of variable concentration of Cerium on meachanoluminescence (ML and photoluminescence behavior were studied. The samples were prepared by combustion a synthesis technique which is suitable for less time taking techniques also for large scale production for phosphors. The starting material used for sample preparation are Sr(NO33, Zr(NO33 XH2O and Ce(NO33 6H2O and urea used as a fuel. The prepared sample was characterized by X-ray diffraction technique (XRD with variable concentration of Ce (0.05–0.5 mol%. There is no any phase change found with increase the concentration of Ce. Sample shows orthorhombic structure and the particle size calculated by Scherer's formula. The surface morphology of prepared phosphor was determined by field emission gun scanning electron microscopy (FEGSEM technique. Mechanoluminescence studies on SrZrO3phosphors doped with Ce and underwent an impulsive deformation with an impact of a piston for Mechanoluminescence (ML investigations. Temporal characteristics in order to investigate about the luminescence centre responsible for ML peak, increasing impact velocity causes more number of electrons will be ionized to reach to the conduction band so there will be more number of electrons available to be recombined at recombination or luminescence centre. In photoluminescence study PL emission spectra show the isolated peak position observed at 388 nm near UV region of spectrum due to 5d–4f transition of Ce3+ion.Thermoluminescence study shows doping of Ce3+ ions reduced the TL intensity TL glow curve shows the high fading and less stability when it doped with cerium. The activation energy high for the doped SrZrO3 phosphor means that the trapped electron is highly trapped in trap level. The present study gives the advance application for fracture

High colour purity single-phased full colour emitting white LED phosphor Sr2V2O7:Eu3+

International Nuclear Information System (INIS)

Zhou Zhi; Zhou Nan; He Zhangxing; Liu Suqin; Liu Younian; Tian Ziwei; Wang Nanfang; Mao Zhiyong; Hintzen, H T

2013-01-01

Single-phased white-light-emitting phosphor Sr 2 V 2 O 7 :Eu 3+ was successfully synthesized by the solid-state method. The result of x-ray diffraction analysis indicated that the obtained phosphor has the same crystal structure as that of Sr 2 V 2 O 7 . The synthesized Sr 2 V 2 O 7 :Eu 3+ was combined with near-UV light (365 nm) chips and then assembled into ligtht-emitting diodes (LED) devices, which generated white light with colour coordinates of (0.324, 0.317). The white light was generated from yellow-green and red emissions, which should be attributed to the host Sr 2 V 2 O 7 and dopant Eu ions, respectively. The effects of the concentration of Eu ions and charge compensation on the emission intensity were carefully investigated. The results show that the energy migrates from the host to the dopant and also that Li 2 CO 3 should be the best charge compensator for this single-phased phosphor. In addition, the colour rendering index and luminescence efficiency of the fabricated LED devices with Sr 1.90 V 2 O 7 :0.10Eu 3+ phosphor were 91 and 32 lm W -1 , respectively, suggesting that Sr 1.90 V 2 O 7 :0.10Eu 3+ phosphor is a potential candidate for the phosphor-converted white-light-emitting diodes with near-UV chips.

Effect of UV irradiation on different types of luminescence of SrAl2 O4 :Eu,Dy phosphors.

Science.gov (United States)

Jha, Piyush

2016-11-01

This paper reports the luminescence behavior of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors under UV-irradiation. The effect of UV-irradiation on afterglow (AG), thermoluminescence (TL) and mechanoluminescence (ML) of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors is investigated. The space group of Sr 0.097 Al 2 O 4 :Eu 0.01 ,Dy 0.02 phosphors is monoclinic P2 1 . The prepared phosphors exhibit a long AG, intense TL and ML. It is found that the AG, ML intensity and TL increase with increasing duration of irradiation time. The ML intensity decreases with successive impact of the load onto the phosphors, whereby the diminished ML intensity can be recovered by UV-irradiation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Synthesis and luminescence properties of novel LiSrPO{sub 4}:Dy{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Sun, Jiayue, E-mail: jiayue_sun@126.com [School of Science, Beijing Technology and Business University, Beijing 100048 (China); Zhang, Xiangyan [School of Science, Beijing Technology and Business University, Beijing 100048 (China); Xia, Zhiguo, E-mail: xiazg426@yahoo.com.cn [School of Materials Sciences and Technology, China University of Geosciences, Beijing 100083 (China); Du, Haiyan [School of Science, Beijing Technology and Business University, Beijing 100048 (China)

2011-11-15

Graphical abstract: Novel LiSrPO4:Dy{sup 3+} phosphors were synthesized by solid-state reaction, and Dy{sup 3+}-doped concentration dependent luminescence properties, concentration quenching effect and the decay times were investigated in detail. Highlights: {yields} LiSrPO{sub 4}:Dy{sup 3+} could be excited by UV light and exhibited blue and yellow emission. {yields} Concentration quenching effect of LiSrPO{sub 4}:Dy{sup 3+} samples were investigated in detail. {yields} Decay times are estimated to be 0.57-0.89 ms for Dy{sup 3+} in LiSrPO{sub 4} host. -- Abstract: Novel LiSrPO{sub 4}:Dy{sup 3+} phosphors for white light-emitting diodes (w-LEDs) were synthesized by the conventional solid-state reaction. X-ray powder diffraction (XRD) analysis confirmed the phase formation of LiSrPO{sub 4}:Dy{sup 3+} materials. Luminescence properties results showed that the phosphor could be efficiently excited by the UV-vis light region from 250 to 460 nm, and it exhibited blue (483 nm) and yellow (574 nm) emission corresponding to {sup 4}F{sub 9/2} {yields} {sup 6}H{sub 15/2} transitions and {sup 4}F{sub 9/2} {yields} {sup 6}H{sub 13}/{sub 2} transitions, respectively. The luminescence intensity of LiSrPO{sub 4}:xDy{sup 3+} phosphor firstly increased and then decreased with increasing Dy{sup 3+} concentration, and reached the maximum at x = 0.03. It was found that concentration quenching occurred as a result of dipole-dipole interaction according to the Dexter's theory. The decay time was also determined for various concentrations of Dy{sup 3+} in LiSrPO{sub 4}.

High-pressure densified solid solutions of alkaline earth hexaborides (Ca/Sr, Ca/Ba, Sr/Ba) and their high-temperature thermoelectric properties

International Nuclear Information System (INIS)

Gürsoy, M.; Takeda, M.; Albert, B.

2015-01-01

Solid solutions of alkaline earth hexaborides were synthesized and densified by spark plasma sintering at 100 MPa. The high-temperature thermoelectric properties (Seebeck coefficients, electrical and thermal diffusivities, heat capacities) were measured between room temperature and 1073 K. CaB 6 , SrB 6 , BaB 6 and the ternary hexaborides Ca x Sr 1−x B 6 , Ca x Ba 1−x B 6 , Sr x Ba 1−x B 6 (x = 0.25, 0.5, 0.75) are n-type conducting compounds over the whole compositional and thermal ranges. The values of the figure of merit ZT for CaB 6 (ca. 0.3 at 1073 K) were found to be significantly increased compared to earlier investigations which is attributed to the densification process. - Highlights: • Solid solutions of alkaline earth hexaborides were synthesized. • High-temperature thermoelectric properties of mixed calcium borides are excellent. • Spark plasma source densification results in high ZT values. • Borides are rare-earth free and refractory materials

Facile preparation and formation mechanism of Sr2Si5N8:Eu2+ red-emitting phosphors

Science.gov (United States)

Wang, Yang; Wang, Yunli; Wang, Ming; Shao, Yiran; Zhu, Yingchun

2018-05-01

The red-emitting Sr2Si5N8:Eu2+ phosphors have been synthesized in a new facile process using (oxy)nitride precursors by inductive calcination under N2 atmosphere at ordinary pressure. Different from the prevailing methods, lower cost raw materials, simpler pretreatment, without harsh conditions and a shorter reaction time are achieved. It was found that red-emitting Sr2Si5N8:Eu2+ phosphors were synthesized with high crystallinity and purity after 1 h inductive calcination. The formation mechanism was characterized by XRD, SEM, TEM and Fluorescence microscopy. It was demonstrated that a hexagonal mesophase of Sr-doped α-Si3N4 was primarily formed in the reaction process, which transformed into the final product of the orthorhombic Sr2Si5N8:Eu2+ phosphors. During the reaction process, the color of the samples transforms from greenish-yellow to orange and eventually to red. The as-prepared phosphors have a wide excitation in the range of 250 ∼ 570 nm which matches blue light chips and give a red-light emission peaking at 610 nm. The results indicate a promising prospect for a simple, efficient and inexpensive way to prepare Sr2Si5N8:Eu2+ phosphors for blue/UV-based warm-white LEDs and other fluorescent applications.

Comparison of the photoluminescence properties of Eu2+, Mn2+ co-doped M5(PO4)3Cl (M = Ca, Sr, Ba)

International Nuclear Information System (INIS)

Yang, Fengli; An, Wei; Wei, Heng-Wei; Chen, Guantong; Zhuang, Weidong; Jing, Xi-Ping

2014-01-01

Highlights: • Good size match between the doped and host cations narrows the emission band. • Low phonon energy of the hosts enhances the luminescence intensity. • “Inverse bottleneck effect” related to Eu/Mn lifetime mismatch causes quenching. • “Charge transfer process” in the Eu–Mn clusters causes quenching. -- Abstract: Eu 2+ and Mn 2+ singly doped or co-doped M 5 (PO 4 ) 3 Cl (M = Ca, Sr and Ba) phosphors were synthesized by conventional solid state reactions and characterized by X-ray diffraction (XRD), photoluminescence (PL) spectra, PL decay curves, energy dispersive spectra (EDS) and Raman spectra. The results show that a better size match between the doped cation and the host cation allows a wider solid solution range (e.g. Ca 2+ /Mn 2+ ) and a narrower emission band (e.g. Sr 2+ /Eu 2+ and Ca 2+ /Mn 2+ ). A lower phonon energy of the host (e.g. the Sr phase) reduces the non-radiation probability and enhances the PL efficiency. The PL performance of the Ba phase is exceptional possibly because of the large size difference between the doped cations and the host cations. The transfer efficiency (η) and the emission quantum efficiency (Q) were analyzed. In the studied phosphors, superficially Eu 2+ efficiently transferred its absorbed energy to Mn 2+ but the Q of the Mn 2+ emission was not as high as expected. Two loss mechanisms are proposed: an “inverse bottleneck effect” and “charge transfer” between Eu 2+ and Mn 2+

Potential tunable white-emitting phosphor LiSr4(BO3)3:Ce3+, Eu2+ for ultraviolet light-emitting diodes

International Nuclear Information System (INIS)

Wang Qian; Deng Degang; Hua Youjie; Huang Lihui; Wang Huanping; Zhao Shilong; Jia Guohua; Li Chenxia; Xu Shiqing

2012-01-01

A novel Ce 3+ /Eu 2+ co-activated LiSr 4 (BO 3 ) 3 phosphor has been synthesized by traditional solid-state reaction. The samples could display varied color emission from blue towards white and ultimately to yellow under the excitation of ultraviolet (UV) light with the appropriate adjustment of the relative proportion of Ce 3+ /Eu 2+ . The resonance-type energy transfer mechanism from Ce 3+ to Eu 2+ in LiSr 4 (BO 3 ) 3 :Ce 3+ , Eu 2+ phosphors is dominant by electric dipole–dipole interaction, and the critical distance is calculated to be about 29.14 Å by the spectra overlap method. White light was observed from LiSr 4 (BO 3 ) 3 :mCe 3+ , nEu 2+ phosphors with chromaticity coordinates (0.34, 0.30) upon 350 nm excitation. The LiSr 4 (BO 3 ) 3 :Ce 3+ , Eu 2+ phosphor has potential applications as an UV radiation-converting phosphor for white light-emitting diodes. - Highlights: ► White light was observed from the novel phosphor with chromaticity coordinate (0.34, 0.30). ► Resonant energy transfer between Ce 3+ and Eu 2+ occurs in the novel phosphor. ► This novel phosphor has potential applications as a UV-driven light-emitting phosphor.

Dielectric enhancement of BaTiO3/SrTiO3 superlattices with embedded Ni nanocrystals

International Nuclear Information System (INIS)

Xiong Zhengwei; Sun Weiguo; Wang Xuemin; Jiang Fan; Wu Weidong

2012-01-01

Highlights: ► The BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs were successfully fabricated by L-MBE. ► The influence with the various concentrations of Ni nanocrystals embedded in BaTiO 3 /SrTiO 3 superlattices was also discussed. ► The BaTiO 3 /SrTiO 3 superlattices with lower concentration of embedded Ni NCs had higher permittivity and dielectric loss compared with the pure BaTiO 3 /SrTiO 3 superlattices. ► The dielectric enhancement of BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs was proposed to explained by Drude quasi-free-electron theory. - Abstract: The self-organized Ni nanocrystals (NCs) were embedded in BaTiO 3 /SrTiO 3 superlattices using laser molecular beam epitaxy (L-MBE). The stress of the composite films was increased with the increasing concentration of embedded Ni NCs, as investigation in stress calculation. The influence with the various concentrations of Ni NCs embedded in BaTiO 3 /SrTiO 3 superlattices was also discussed. The internal stress of the films was too strong to epitaxial growth of BaTiO 3 /SrTiO 3 superlattices. Compared with the pure BaTiO 3 /SrTiO 3 superlattices, the BaTiO 3 /SrTiO 3 superlattices with lower concentration of embedded Ni NCs had higher permittivity and dielectric loss. Furthermore, the dielectric enhancement of BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs was proposed to explained by Drude quasi-free-electron theory.

Luminescence properties of Na2Sr2Al2PO4Cl9:Sm3+ phosphor

Science.gov (United States)

Tamboli, Sumedha; Shahare, D. I.; Dhoble, S. J.

2018-04-01

A series of Sm3+ ions doped Na2Sr2Al2PO4Cl9 phosphors were synthesized via solid state synthesis method. Photoluminescence (PL) emission spectra were obtained by keeping excitation wavelength at 406 nm. Emission spectra show three emission peaks at 563 nm, 595 nm and 644 nm. The CIE chromaticity diagram shows emission colour of the phosphor in the orange-red region of the visible spectrum, indicating that the phosphor may be useful in preparing orange light-emitting diodes. Na2Sr2Al2PO4Cl9:Sm3+ phosphors were irradiated by γ-rays from a 60Co source and β-rays from a 90Sr source. Their thermoluminescence (TL) glow curves were obtained by Nucleonix 1009I TL reader. TL Trapping parameters such as activation energy of trapped electrons and order of kinetics were obtained by using Chen's peak shape method, Glow curve fitting method and initial rise method.

Synthesis and Luminescent Properties of Sr{sub 2}SiO{sub 4} Phosphors

Energy Technology Data Exchange (ETDEWEB)

Nishioka, H; Watari, T; Eguchi, T; Yada, M, E-mail: watarit@cc.saga-u.ac.jp [Graduate School of Science and Engineering, Saga University, 1 Hojo-Machi, Saga 840-8502 (Japan)

2011-05-15

Sr{sub 2}SiO{sub 4}:Eu{sup 2+} phosphors and Sr{sub 2}SiO{sub 4}:Eu{sup 2+}, Dy{sup 3+} persistent phosphors were synthesized by solid-state reaction method at 1300deg. C using SrCO{sub 3}, SiO{sub 2}(silica: 3 {mu} m and fumed silica: 7nm), Eu{sub 2}O{sub 3}(0.01 to 0.06 mol% Eu) and Dy{sub 2}O{sub 3}(0.005 to 0.02 mol% Dy) powders. The amount of the stable {beta}- Sr{sub 2}SiO{sub 4} phase had decreased and the amount of the {alpha}'-Sr{sub 2}SiO{sub 4} increased with the increase of the Eu content. The solid solution of Eu{sup 2+} ion stabilized {alpha}'-Sr{sub 2}SiO{sub 4} at room temperature. The emission color of the Sr{sub 2}SiO{sub 4}:Eu{sup 2+} products changed from the turquoise blue to yellow with the increase of the Eu content. The maximum emission peak position changed to the higher wavelength with the increase of the Eu content. The emission peak at 490nm(green color) was from {beta}- Sr{sub 2}SiO{sub 4} phase and that at 560nm(yellow color) was from {alpha}'-Sr{sub 2}SiO{sub 4} phase. The change of the phase content in the products affects the color and the emission peak. The emission intensity of the products from fumed silica is stronger than the products from silica. Sr{sub 1.98-x}SiO{sub 4}:Eu{sub 0.02}, Dy{sub x} persistent phosphors products showed the persistent emission for a few minutes with the naked eyes. The behavior was observed from all products. The product from fumed silica at x = 0.01 showed the strong emission for tens of seconds.

Phase equilibrium in Al-Li-Ca(Sr, Ba) systems at 423 K

International Nuclear Information System (INIS)

Ganieva, N.I.; Nazarov, Kh.M.; Ganiev, I.N.

1999-01-01

The isothermic cross section of the Al-Li-Ca(Sr, Ba) systems at 423 K is obtained. It is shown that the Al-Li-Sr ternary system as well as the Li-Sr binary system differ by nature of components in interaction from the Al-Li-Ca(Ba) systems. This is obvious by formation of the SrAl 2 Li 2 ternary intermetallide, which is not observed in the systems with participation of barium and calcium [ru

Synthesis and characterization of Sr2CeO4: Eu3+ phosphor by different forms

International Nuclear Information System (INIS)

Murthy, K.V.R.; Rao, Ch. Atchyutha; Suresh, K.; Ratna Kumar, B.W.; Nageswara Rao, B.; Poornachandra Rao, N.V.; Subba Rao, B.

2011-01-01

High temperature solid state reaction method was explored to synthesize undoped Sr 2 CeO 4 and Eu 3+ RE doped Sr 2 CeO 4 phosphor using inorganic materials taking in three different forms like, form (i) Strontium Carbonate (SrCO 3 ), Cerium Oxide (CeO 2 ), (ii) Strontium Nitrate (Sr(NO 3 ) 2 ), Cerium Oxide (CeO 2 ) and (iii) Strontium Nitrate (Sr(NO 3 ) 2 ), Cerium Nitrate (Ce(NO 3 ) 3 .6(NH 2 .CO.NH 2 ) in stoichiometric proportions of Sr:Ce as 2:1 and ground into a fine powder using agate mortar and pestle about an hour. The grounded samples were placed in an alumina crucible and fired at 1200 deg C for 3 hours in a muffle furnace with a heating rate of 5 deg C/min. To investigate the crystal structure, phase, morphology and luminescent properties of the synthesized phosphors XRD, SEM, Photoluminescence (PL) spectra, TL and CIE techniques were used. The Photoluminescence (PL) emission and excitation spectra were measured by Spectrofluorophotometer (SHIMADZU, RF-5301 PC) using Xenon lamp as excitation source. To identify the crystal phase, XRD analysis was carried out with a powder diffractometer (Rigaku-D/max 2500) using CuKα radiation. The microstructures of the samples were studied using a scanning electron microscopy (SEM) (XL 30 CP Philips). All the analysis was recorded at room temperature. We have compared the results of the prepared samples by different forms. From the XRD analysis it was found that the prepared phosphors are mostly in single phase of Sr 2 CeO 4 with an orthorhombic structure. From the XRD data, using Scherrer's formula the calculated average crystallite size is (i) ∼ 28 nm (ii) ∼ 9 nm (iii) ∼ 7 nm using FWHM. This indicates that, the prepared phosphors via high temperature solid state reaction method is in nano size. Sr 2 CeO 4 exhibits photoluminescence due to the charge transfer (CT) mechanism. The sample displays a broad excitation spectrum range from ∼ 220 to 400 nm. Under 350 nm excitation, the undoped Sr 2 CeO 4 shows

Synthesis and photoluminescence spectroscopy of BaGeF6:Mn4+ red phosphor

Science.gov (United States)

Sekiguchi, Daisuke; Adachi, Sadao

2015-04-01

We synthesized Mn4+-activated BaGeF6 red phosphor by the chemical reaction method from HF, H2SiF6, BaF2, KMnO4, and GeO2 powder. The structural and optical properties of BaGeF6:Mn4+ were investigated using X-ray diffraction analysis, secondary electron microscopy observation, electron spin resonance measurement, photoluminescence (PL), PL excitation (PLE) and Raman scattering spectroscopies, and luminescence decay time measurement. Temperature dependence of the PL intensity was measured from T = 20 to 500 K and analyzed by taking into consideration the Bose-Einstein phonon occupation number. The PLE spectra measured at T = 20 and 300 K and luminescence decay time at T = 20-460 K were also analyzed based on the Franck-Condon and conventional thermal quenching models, respectively. Comprehensive discussion was given on the Mn4+-related PL properties and Raman scattering behaviors in a family of the barium hexafluorometallate phosphors.

Green-emissive transparent BaSi 2O 5:Eu 2 + film phosphor on quartz glass created by a sputtering thermal diffusion process

Science.gov (United States)

Seo, K. I.; Park, J. H.; Kim, J. S.; Na, Y. H.; Choi, J. C.; Bae, J. S.

2009-10-01

Eu 2+-doped BaSi 2O 5 film phosphors on quartz substrates are fabricated by radio-frequency magnetron sputtering thermal diffusion. The BaSi 2O 5: Eu 2+ phosphor crystals have some preferred orientations that are lattice-spacing matched with the crystallized β- SiO 2 crystals, and they show pore and grain boundary-free morphology with a rod-like shape fused into the crystallized β- SiO 2 crystals. The BaSi 2O 5: Eu 2+ film phosphor has a high transparency, with a transmittance of about 30% in visible light. The BaSi 2O 5: Eu 2+ film phosphor shows 510 nm green emission from the f-d transition of the Eu 2+ ions, and in particular the best sample shows a green photoluminescence brightness of about 5% of a BaSi 2O 5: Eu 2+ powder phosphor screen. These excellences in optical properties can be explained by less optical scattering at pores or grain boundaries, and less reflection at the continuously index-changed interface.

Separation of Sr from Ca, Ba and Ra by means of Ca(OH)2 and Ba(Ra)Cl2 or Ba(Ra)SO4 for the determination of radiostrontium

DEFF Research Database (Denmark)

Chen, Q.J.; Hou, Xiaolin; Yu, Y.X.

2002-01-01

be completed. The new separation procedure has been successfully used for the determination of Sr-90 in samples with high Ca content, such as 451 of seawater and 2001 of drinking water. The analytical quality of the results is comparable to that of the traditional method using fuming nitric acid and BaCrO4......A simple procedure is developed to separate Sr from a large amount of Ca, which relies on the insolubility of Ca(OH)(2) in alkaline solution. Calcium is quantitatively separated from Sr and more than 95% of Sr is recovered from a sample with as much as 50 g of Ca and a Ca/Sr mole ratio of 250....... A new procedure for the separation of Sr from Ba and Ra is also investigated, which is based on the difference in solubility of the chlorides of Sr, Ba and Ra in HCl media. In 9.5 mol 1(-1) HCl or 7.5 mol 1(-1) HCl-10% acetone media, >97% of Ba and Ra can be removed by Ba(Ra)Cl-2 precipitation, and >94...

Photoluminescence characteristics of Sm{sup 3+}-doped Ba{sub 2}CaWO{sub 6} as new orange–red emitting phosphors

Energy Technology Data Exchange (ETDEWEB)

Yu, Ruiijn [College of Science, Northwest A and F University, Yangling, Shaanxi 712100 (China); Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Mi Noh, Hyeon; Kee Moon, Byung; Chun Choi, Byung [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Hyun Jeong, Jung, E-mail: jhjeong@pknu.ac.kr [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Sueb Lee, Ho [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jang, Kiwan, E-mail: kwjang@changwon.ac.kr [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Soo Yi, Soung [Department of Electronic Material Engineering, Silla University, Busan 617-736 (Korea, Republic of)

2014-08-01

The orange–red emitting Ba{sub 2}CaWO{sub 6}:xSm{sup 3+} (0.01≤x≤0.25) phosphors were synthesized via solid state reaction process. The crystal structure of the phosphor was characterized by XRD. The photoluminescence excitation and emission spectra, concentration effect were investigated. The results show an efficient energy transfer from WO{sub 6}{sup 6−} group to Sm{sup 3+} occurs. The emission spectra of the Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} phosphors consisted of some sharp emission peaks of Sm{sup 3+} ions centre at 579 nm, 618 nm, 625 nm, and 675 nm. The strongest one is located at 610 nm due to {sup 4}G{sub 5/2}→{sup 6}H{sub 7/2} transition of Sm{sup 3+}, generating bright orange–red light. The optimum dopant concentration of Sm{sup 3+} ions in Ba{sub 2}CaWO{sub 6}:xSm{sup 3+} is around 5 mol% and the critical transfer distance of Sm{sup 3+} is calculated as 18 Å. The fluorescence lifetime of Sm{sup 3+} in Ba{sub 2}CaWO{sub 6}:0.05Sm{sup 3+} is 2.36 ms. The Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} phosphors may be potentially used as orange–red phosphors for white light-emitting diodes. - Highlights: • A new host-sensitized Sm{sup 3+}-doped Ba{sub 2}CaWO{sub 6} phosphor was firstly synthesized. • Its structure, luminescent properties are well studied and characterized. • There exists an efficient energy transfer from WO{sub 6}{sup 6−} group to Sm{sup 3+}. • The thermal quenching properties of Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} was firstly evaluated.

Photoluminescence characteristics of Sm{sup 3+} doped Ba{sub 3}La(PO{sub 4}){sub 3} as new orange-red emitting phosphors

Energy Technology Data Exchange (ETDEWEB)

Yu, Ruijin [College of Science, Northwest A and F University, Yangling, Shaanxi 712100 (China); Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Mi Noh, Hyeon; Kee Moon, Byung; Chun Choi, Byung [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Hyun Jeong, Jung, E-mail: jhjeong@pknu.ac.kr [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Sueb Lee, Ho [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jang, Kiwan, E-mail: kwjang@changwon.ac.kr [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Soo Yi, Soung [Department of Electronic Material Engineering, Silla University, Busan 617-736 (Korea, Republic of)

2014-01-15

A series of orange-red emitting Ba{sub 3}La(PO{sub 4}){sub 3}:xSm{sup 3+} (0.01≤x≤0.30) phosphors was synthesized by the convenient solid-state reaction. X-ray diffraction and photoluminescence spectra were utilized to characterize the structure and luminescence properties of the as-synthesized phosphors. The emission spectra of the Ba{sub 3}La(PO{sub 4}){sub 3}:Sm{sup 3+} phosphors consisted of some sharp emission peaks of Sm{sup 3+} ions centered at 563 nm, 600 nm, 647 nm, 710 nm. The strongest one is located at 600 nm due to {sup 4}G{sub 5/2}–{sup 6}H{sub 7/2} transition of Sm{sup 3+}, generating bright orange-red light. The optimum dopant concentration of Sm{sup 3+} ions in Ba{sub 3}La(PO{sub 4}):xSm{sup 3+} is around 5 mol% and the critical transfer distance of Sm{sup 3+} is calculated as 22 Å. The CIE chromaticity coordinates of the Ba{sub 3}La(PO{sub 4}){sub 3}:0.05Sm{sup 3+} phosphors was is located in the orange reddish region. The Ba{sub 3}La(PO{sub 4}){sub 3}:Sm{sup 3+} phosphors may be potentially used as red phosphors for white light-emitting diodes. -- Highlights: • A new Sm{sup 3+}-doped Ba{sub 3}La(PO{sub 4}){sub 3} phosphor was firstly synthesized. • Its structure, luminescent properties are well studied and characterized. • The Ba{sub 3}La(PO{sub 4}){sub 3}:Sm{sup 3+} shows bright orange reddish emissions under UV excitation.

Sr(1.7)Zn(0.3)CeO4: Eu3+ novel red-emitting phosphors: synthesis and photoluminescence properties.

Science.gov (United States)

Li, Haifeng; Zhao, Ran; Jia, Yonglei; Sun, Wenzhi; Fu, Jipeng; Jiang, Lihong; Zhang, Su; Pang, Ran; Li, Chengyu

2014-03-12

A series of novel red-emitting Sr1.7Zn0.3CeO4:Eu(3+) phosphors were synthesized through conventional solid-state reactions. The powder X-ray diffraction patterns and Rietveld refinement verified the similar phase of Sr1.7Zn0.3CeO4:Eu(3+) to that of Sr2CeO4. The photoluminescence spectrum exhibits that peak located at 614 nm ((5)D0-(7)F2) dominates the emission of Sr1.7Zn0.3CeO4:Eu(3+) phosphors. Because there are two regions in the excitation spectrum originating from the overlap of the Ce(4+)-O(2-) and Eu(3+)-O(2-) charge-transfer state band from 200 to 440 nm, and from the intra-4f transitions at 395 and 467 nm, the Sr1.7Zn0.3CeO4:Eu(3+) phosphors can be well excited by the near-UV light. The investigation of the concentration quenching behavior, luminescence decay curves, and lifetime implies that the dominant mechanism type leading to concentration quenching is the energy transfer among the nearest neighbor or next nearest neighbor activators. The discussion about the dependence of photoluminescence spectra on temperature shows the better thermal quenching properties of Sr1.7Zn0.3CeO4:0.3Eu(3+) than that of Sr2CeO4:Eu(3+). The experimental data indicates that Sr1.7Zn0.3CeO4:Eu(3+) phosphors have the potential as red phosphors for white light-emitting diodes.

Boron-Containing Red Light-Emitting Phosphors And Light Sources Incorporating The Same

Science.gov (United States)

Srivastava, Alok Mani; Comanzo, Holly Ann; Manivannan, Venkatesan

2006-03-28

A boron-containing phosphor comprises a material having a formula of AD1-xEuxB9O16, wherein A is an element selected from the group consisting of Ba, Sr, Ca, Mg, and combinations thereof; D is at least an element selected from the group consisting of rare-earth metals other than europium; and x is in the range from about 0.005 to about 0.5. The phosphor is used in a blend with other phosphors in a light source for generating visible light with a high color rendering index.

Photoluminescence study of Dy3+ doped SrCeVO5 phosphor

International Nuclear Information System (INIS)

Suresh, K.; Dai, Ch. Vijay Anil; Murthy, K.V.R.

2016-01-01

Dy 3+ doped SrCeVO 5 phosphor was synthesized by the solid-state reaction method. Photoluminescence (PL) technique was performed to characterize the sample. The excitation spectra monitored under 520 nm and 610 nm wavelength was characterized by a broad band ranging from 220-400 nm. From the excitation spectra two main bands at 265 nm and 325 nm were observed. The PLE intensity of 520 nm monitored shows high intensity than 610 nm spectrum. The emission spectra of SrCeVO 5 phosphor under excitations at 265 nm and 325 nm exhibited main peak at 515 nm (cyan) which is a strong, intense well resolved peak with FWHM (full width at half maximum) of 130 nm is observed. This emission is mainly may be due to Ce ion but not Dy ion. The same emission under 640 and 670 nm excitations (up conversion) with good intensity was also observed. Commission international de l'eclairage (CIE) co-ordinates under these excitations revealed that this phosphor emit cyan colour and could be used for the generation of white light in display and lamp devices. (author)

Synthesis and luminescence properties of SrMoO{sub 4}:RE{sup 3+} (RE = Eu or Tb) phosphors

Energy Technology Data Exchange (ETDEWEB)

Cho, Shinho [Silla University, Busan (Korea, Republic of)

2014-05-15

SrMoO{sub 4}:RE{sup 3+} (RE = Eu or Tb) phosphors were synthesized with different concentrations of activator ions by using the conventional solid-state reaction method. The effects of the concentration of activator ions on the structural, morphological, and optical properties of strontium molybdate phosphors were investigated by using X-ray diffraction, scanning electron microscopy, and fluorescence spectrophotometry, respectively. XRD patterns revealed that all synthesized phosphors showed the tetragonal SrMoO{sub 4} structure, irrespective of the type and the concentration of activator ions. The crystallite size showed an overall increasing tendency with increasing concentration of activator ions. The emission spectra of Eu{sup 3+}-doped SrMoO{sub 4} phosphors under excitation at 295 nm exhibited one intense red band at 619 nm and five weak bands centered at 541, 561, 596, 657, and 704 nm, respectively. For the Tb{sup 3+}-doped SrMoO{sub 4} phosphors, a strong emission peak at 550 nm and two weak lines, 494 and 591 nm, were observed. The intensities of all the emission bands reached maxima when 0.05 mol of Tb{sup 3+} ions was used. The results suggest that the optimum concentrations for synthesizing highly-luminescent red and green phosphors are 0.01 mol and 0.05 mol, respectively.

Optimized photoluminescence of SrB 2O 4:Eu 3+ red-emitting phosphor by charge compensation

Science.gov (United States)

Zhao, Lai-Shi; Liu, Jie; Wu, Zhan-Chao; Kuang, Shao-Ping

2012-02-01

A novel red-emitting phosphor, SrB 2O 4:Eu 3+, was synthesized by high temperature solid-state reaction and its photoluminescence properties were studied. The emission spectrum consists of four major emission bands. The emission peaks are located at 593, 612, 650 and 703 nm, corresponding to the 5D0 → 7F1, 5D0 → 7F2, 5D0 → 7F3 and 5D0 → 7F4 typical transitions of Eu 3+, respectively. The effects of Eu 3+ doping content and charge compensators (Li +, Na +, K +) on photoluminescence of SrB 2O 4:Eu 3+ phosphor were studied. The results show that the emission intensity can be affected by above factors and Na + is the optimal charge compensator for SrB 2O 4:Eu 3+. The photoluminescence of NaSrB 2O 4:Eu 3+ was compared with that of Y 2O 2S:Eu 3+. It implies that SrB 2O 4:Eu 3+ is a good candidate as a red-emitting phosphor pumped by near-ultraviolet (NUV) InGaN chip for fabricating white light-emitting diodes (WLEDs).

Photoluminescence properties and thermal stability of blue-emitting Ba5-xCl(PO4)3:xEu2+ (0.004≤x≤0.016) phosphors.

Science.gov (United States)

Liu, Jie; Zhang, Zhi-Ming; Wu, Zhan-Chao; Wang, Fang-Fang; Li, Zhen-Jiang; Kuang, Shao-Ping; Wu, Ming-Mei

2017-01-15

A series of blue-emitting Ba 5-x Cl(PO 4 ) 3 :xEu 2+ (0.004≤x≤0.016) phosphors were synthesized by conventional high-temperature solid state reaction. The structure and photoluminescence (PL) properties of the phosphors were investigated. The as-prepared phosphors exhibit broad excitation band ranging from 250 to 420nm, and strong asymmetric blue emission band peaking at 436nm. The optimum concentration of Eu 2+ in the Ba 5 Cl(PO 4 ) 3 :Eu 2+ phosphor is x=0.01, and the concentration quenching mechanism is verified to be the combined actions of dipole-dipole interaction and radiation re-absorption mechanism. The thermal stability of Ba 5 Cl(PO 4 ) 3 :Eu 2+ was evaluated by temperature-dependent PL spectra. Compared with that of commercial BaMgAl 10 O 17 :Eu 2+ (BAM) phosphor, the Ba 5-x Cl(PO 4 ) 3 :xEu 2+ phosphors exhibit similarly excellent thermal quenching property. In addition, the CIE chromaticity coordinates of Ba 5-x Cl(PO 4 ) 3 :xEu 2+ (0.004≤x≤0.016) were calculated to evaluate the color quality. All the results indicate that Ba 5 Cl(PO 4 ) 3 :Eu 2+ is a promising candidate phosphor for near-ultraviolet (n-UV) pumped LED. Copyright © 2016 Elsevier B.V. All rights reserved.

Crystal structure and luminescence properties of a novel red-emitting phosphor BaAlBO{sub 3}F{sub 2}:Eu{sup 3+}

Energy Technology Data Exchange (ETDEWEB)

Chen, Wanping, E-mail: cwp0918@aliyun.com; Zhou, Ahong; Liu, Yan; Dai, Xiaoyan; Yang, Xin

2014-12-15

A series of novel red-emitting phosphors BaAlBO{sub 3}F{sub 2}:xEu{sup 3+} (0.001≤x≤0.08) were first synthesized via a high temperature solid-state reaction. X-ray diffraction and photoluminescence spectroscopy were used to characterize the crystal structure and photoluminescence properties of the phosphor, respectively. The phosphor can be effectively excited with a 395 nm light, and shows a dominant {sup 5}D{sub 0}−{sup 7}F{sub 2} emission with chromatic coordination of 0.628 and 0.372. The optimal doping concentration is about 0.04. Rietveld refinement results and the luminescence behavior of Eu{sup 3+} indicate that the Eu{sup 3+} ion occupies a C{sub 3} symmetry site, and the host BaAlBO{sub 3}F{sub 2} has a hexagonal structure with P-6 space group. In addition, the phosphor could be a potential candidate as red-emitting phosphor for application in white light-emitting diode. - Graphical abstract: The luminescence behavior and Rietveld refinement of BaAlBO{sub 3}F{sub 2}:Eu{sup 3+} indicate that the red-emitting phosphor has potential application in white LED and the host has a hexagonal structure with P-6 space group. - Highlights: • A novel red-emitting phosphor BaAlBO{sub 3}F{sub 2}:Eu{sup 3+} is first synthesized. • The crystal structure of BaAlBO{sub 3}F{sub 2} is confirmed. • The phosphor shows potential application in white LED.

Surface and spectral studies of green emitting Sr{sub 3}B{sub 2}O{sub 6}:Tb{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Neharika [School of Physics, Shri Mata Vaishno Devi University, Katra 182320, J& K (India); Kumar, Vinay, E-mail: vinaykumar@smvdu.ac.in [School of Physics, Shri Mata Vaishno Devi University, Katra 182320, J& K (India); Sharma, J.; Singh, Vivek K. [School of Physics, Shri Mata Vaishno Devi University, Katra 182320, J& K (India); Ntwaeaborwa, O.M.; Swart, H.C. [Department of Physics, University of the Free State, PO Box 339, Bloemfontein ZA9300 (South Africa)

2016-01-15

Highlights: • XPS technique has been used to study the surface composition of the phosphor. • The phosphor is synthesized by combustion method using urea as fuel. • Multipole–multipole interaction was found to play a key role for concentration quenching of Tb{sup 3+} doped Sr{sub 3}B{sub 2}O{sub 6} phosphor. - Abstract: In this paper, we report the synthesis of trivalent Tb{sup 3+} doped Sr{sub 3}B{sub 2}O{sub 6} phosphor by combustion method using urea as an organic fuel. The structure of the product has been verified by X-ray diffraction study which shows a rhombohedral phase with a space group of R-3c having lattice constants a = 9.064 Å, b = 9.064 Å, c = 12.611 Å. X-ray photoelectron spectroscopy has been used to study the elemental composition and electronic states of the Tb{sup 3+} doped Sr{sub 3}B{sub 2}O{sub 6} phosphor. Photoluminescence spectra showed that the phosphor emits in the greenish region (with the main peak at 544 nm) of color gamut under UV excitation. The diffuse reflectance spectra of the Sr{sub 3}B{sub 2}O{sub 6} phosphor were studied. Lifetime and band gap of the phosphors were calculated to be 2.55 ms and 5.25 ± 0.02 eV, respectively.

Study on luminescence and thermal stability of blue-emitting Sr_5(PO_4)_3F: Eu"2"+phosphor for application in InGaN-based LEDs

International Nuclear Information System (INIS)

Liu, Jie; Zhang, Zhi-Ming; Wu, Zhan-Chao; Wang, Fang-Fang; Li, Zhen-Jiang

2017-01-01

Highlights: • A blue phosphor Sr_5(PO_4)_3F: Eu"2"+ was prepared at low temperature of 800 °C. • The broad excitation band of the phosphor matches well with NUV LED chips. • The phosphor shows high color purity and good color stability. • A bright blue-emitting LED was fabricated with this phosphor on an InGaN chip. - Abstract: A series of blue-emitting phosphors Sr_5(PO_4)_3F: Eu"2"+ were synthesized by traditional high temperature solid-state reaction method. The micro-morphology and photoluminescence properties of the phosphors were investigated. The Sr_5(PO_4)_3F: Eu"2"+ phosphors exhibit broad excitation spectra ranging from 250 to 420 nm, and an intense asymmetric blue emission band peaking at 435 nm. Two different Eu"2"+ emission centers in Sr_5(PO_4)_3F: Eu"2"+ phosphors were confirmed via their fluorescence properties. The concentration quenching mechanism, fluorescence lifetime and thermal stability of Sr_5(PO_4)_3F: Eu"2"+ phosphors were studied in detail. The thermal stability can be improved obviously by anion substitution. The CIE chromaticity coordinates of Sr_5(PO_4)_3F: Eu"2"+ phosphors with different Eu"2"+-doped concentrations were calculated. A blue light-emitting diode was fabricated by combination of a 370 nm InGaN chip and the prepared phosphor Sr_5(PO_4)_3F: Eu"2"+. The present work suggests that Sr_5(PO_4)_3F: Eu"2"+ is a potential phosphor applied in InGaN-based LEDs.

Photoluminescence in Pb{sup 2+} activated SrB{sub 4}O{sub 7} and SrB{sub 2}O{sub 4} phosphors

Energy Technology Data Exchange (ETDEWEB)

Gawande, A.B., E-mail: gawandeab@gmail.com [Department of Physics, SGB Amravati University, Amravati-444602, Maharashtra (India); Ingle, J.T. [J. D. Institute of Engineering and Technology, Yavatmal, Maharashtra (India); Sonekar, R.P., E-mail: sonekar_rp@yahoo.com [Department of Physics, G.S. College, Khamgaon District, Buldhana, Maharashtra (India); Omanwar, S.K. [Department of Physics, SGB Amravati University, Amravati-444602, Maharashtra (India)

2014-05-01

The powder samples of SrB{sub 4}O{sub 7}:Pb{sup 2+} and SrB{sub 2}O{sub 4}:Pb{sup 2+} were prepared by solution combustion synthesis method. The synthesis is based on the exothermic reaction between the fuel (Urea) and Oxidizer (Ammonium nitrate). The synthesized materials were characterized using TG–DTA, powder XRD, SEM and the photoluminescence properties were studied using a Hitachi F-7000 spectrophotometer at room temperature. Both the samples SrB{sub 4}O{sub 7}:Pb{sup 2+} and SrB{sub 2}O{sub 4}:Pb{sup 2+} show broad emission of Pb{sup 2+} respectively at 307 nm and 360 nm (corresponds to {sup 3}P{sub 1} to {sup 1}S{sub 0} transition). The optimum concentrations of Pb{sup 2+} in both the phosphors SrB{sub 4}O{sub 7}:Pb{sup 2+} and SrB{sub 2}O{sub 4}:Pb{sup 2+} were found to be 3 mol% (relative to Sr) and for this concentration the critical transfer distance R{sub 0} were calculated to be 10.21 Å and 12.22 Å respectively. The Stokes shifts were calculated to be respectively 4464 cm{sup −1} and 8454 cm{sup −1}. The emission bands of both the phosphors are in the UV region and the phosphors can be potential candidates for application in UV lamps. - Highlights: • SrB{sub 4}O{sub 7}:Pb{sup 2+} and SrB{sub 2}O{sub 4}:Pb{sup 2+} have been synthesized by Novel solution combustion synthesis technique. • The synthesized materials were characterized using TG–DTA, powder XRD and SEM. • Photoluminescence spectra of synthesized materials showed the characteristic transition in Pb{sup 2+}. • Stokes shift, optimum concentration and critical transfer distance R{sub 0} were determined.

Phase diagrams for systems Cu2S-AIIS (AII=Mg, Ca, Sr, Ba)

International Nuclear Information System (INIS)

Andreev, O.V.; Sikerina, N.V.; Solov'eva, A.V.

2005-01-01

By the methods of physicochemical analysis phase diagrams of Cu 2 S-A II S (A II =Mg, Ca, Sr, Ba) systems are studied. The system Cu 2 S-SrS is of eutectic type with eutectic coordinates 1095 K and 21.5 mol.% of SrS. Solubility of SrS in Cu 2 S is 2 mol.% at 1095 K. Regularities of phase diagram changes of Cu 2 S-A II S (A II =Mg, Ca, Sr, Ba) system are determined. Thermodynamic analysis is done [ru

Luminescence and thermoluminescence properties of Sr{sub 3}WO{sub 6}:Eu{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Emen, F.M., E-mail: femen106@gmail.com [Department of Chemistry, Faculty of Arts and Science, Mehmet Akif Ersoy University, TR 15030, Burdur (Turkey); Altinkaya, R. [Department of Chemistry, Faculty of Arts and Science, Mersin University, TR 33343, Mersin (Turkey)

2013-02-15

Sr{sub 3-x}WO{sub 6}:xEu{sup 3+} (x varies from 0.01 to 0.06) phosphors have been prepared at high temperature by the solid-state method. The crystal structure of Sr{sub 2.95}WO{sub 6}:0.05Eu{sup 3+} phosphor has been determined as a triclinic P-1 space group with a=8.3608 (19) A, b=8.2903 (24) A, c=8.2145 (23) A, {alpha}=89.79 (3){sup Degree-Sign }, {beta}=89.82 (3){sup Degree-Sign }, and {gamma}=89.753 (22){sup Degree-Sign }. The excitation spectrum of Sr{sub 2.95}WO{sub 6}:0.05Eu{sup 3+} phosphor reveals five excitation bands: one is assigned to the charge-transfer (CTLM) band of Sr{sub 3}WO{sub 6} host at 307 nm, and another is assigned to intra-4f transitions between 393 nm and 600 nm. The emission spectrum of Sr{sub 2.95}WO{sub 6}:0.05Eu{sup 3+} phosphor exhibits a series of emission bands, which are attributed to the {sup 5}D{sub 0}{yields}{sup 7}F{sub j} (j=0-4) transitions of Eu{sup 3+} ions. The luminescence studies revealed that the Eu{sup 3+} ions show high luminescent efficiency in emitting red light at 616 nm. The thermoluminescence glow curve shows one dominant glow peak observed at 56 Degree-Sign C which is related to the defects at shallow trap depth. The trap parameters mainly activation energy (E{sub a}) and the order of the kinetics (b) were evaluated by using Rasheedy's three points method (TPM). - Highlights: Black-Right-Pointing-Pointer The Sr{sub 3}WO{sub 6}:Eu{sup 3+} phosphor was prepared by using conventional ceramic method. Black-Right-Pointing-Pointer The diffraction peaks of phosphor have been indexed to triclinic system. Black-Right-Pointing-Pointer The emission peak at 616 nm belongs to {sup 5}D{sub 0}{yields}{sup 7}F{sub 2} electric dipole transitions of Eu{sup 3+}. Black-Right-Pointing-Pointer The emission band of WO{sub 6} and excitation bands of Eu{sup 3+} are overlapping each other. Black-Right-Pointing-Pointer The energy transfer from WO{sub 6} groups to the Eu{sup 3+} ions occurs under the UV excitation.

Luminescence properties of Sm{sup 3+}-doped Sr{sub 3}Sn{sub 2}O{sub 7} phosphor

Energy Technology Data Exchange (ETDEWEB)

Lei Bingfu, E-mail: tleibf@jnu.edu.cn [Department of Physics, Jinan University, Guangzhou 510632 (China); Department of Chemistry and Nanochemistry Institute, Jinan University, Guangzhou 510632 (China); Man Shiqing [Department of Chemistry and Nanochemistry Institute, Jinan University, Guangzhou 510632 (China); Department of Electronic Engineering, Jinan University, Guangzhou 510632 (China); Liu Yingliang [Department of Chemistry and Nanochemistry Institute, Jinan University, Guangzhou 510632 (China); Yue Song [Department of Physics, Jinan University, Guangzhou 510632 (China)

2010-12-01

We report on a luminescent phenomenon in Sm{sup 3+}-doped Sr{sub 3}Sn{sub 2}O{sub 7} afterglow phosphor. XRD, photoluminescence, afterglow emission spectra and long-lasting phosphorescence decay curve are used to characterize this phosphor. After irradiation by a 267-nm UV light for 5 min, the Sm{sup 3+}-doped Sr{sub 3}Sn{sub 2}O{sub 7} phosphor emits intense reddish-orange emitting afterglow from the {sup 4}G{sub 5/2} to {sup 6}H{sub J} (J = 5/2, 7/2, 9/2) transitions, and its afterglow can be seen with the naked eye in the dark clearly for more than 1 h after removal of the excitation source. Photoluminescence spectra reveal that the reddish-orange light-emitting long-lasting phosphorescence originate from the mixture of Sm{sup 3+} characteristic transitions. The afterglow decay curve of the Sm{sup 3+}-doped Sr{sub 3}Sn{sub 2}O{sub 7} phosphor contains a fast decay component and another slow decay one. The possible mechanism of this reddish-orange light-emitting LLP phosphor is also discussed based on the experiment results.

Energy transfer in M₅(PO₄)₃  F:Eu²⁺,Ce³⁺ (M = Ca and Ba) phosphors.

Science.gov (United States)

Shinde, K N; Dhoble, S J

2014-08-01

M5(PO4)3F:Eu(2+) (M = Ca and Ba) co-doped with Ce(3+) phosphors were successfully prepared by the combustion synthesis method. The introduction of co-dopant (Ce(3+)) into the host enhanced the luminescent intensity of the M5(PO4)3F:Eu(2+) (M = Ca and Ba) efficiently. Previously, we have reported the synthesis and photoluminescence properties of same phosphors. The aim of this article is to report energy transfer mechanism between Ce(3+) ➔Eu(2+) ions in M5(PO4)3F:Eu(2+) (M = Ca and Ba) phosphors, where Ce(3+) ions act as sensitizers and Eu(2+) ions act as activators. The M5(PO4)3F:Eu(2+) (M = Ca and Ba) co-doped with Ce(3+) phosphor exhibits great potential for use in white ultraviolet (UV) light-emitting diode applications to serve as a single-phased phosphor that can be pumped with near-UV or UV light-emitting diodes. Copyright © 2013 John Wiley & Sons, Ltd.

Color-tunable and highly thermal stable Sr_2MgAl_2_2O_3_6:Tb"3"+ phosphors

International Nuclear Information System (INIS)

Zhang, Haiming; Zhang, Haoran; Liu, Yingliang; Lei, Bingfu; Deng, Jiankun; Liu, Wei-Ren; Zeng, Yuan; Zheng, Lingling; Zhao, Minyi

2017-01-01

Tb"3"+ activated Sr_2MgAl_2_2O_3_6 phosphor was prepared by a high-temperature solid-state reaction route. The X-ray diffraction, scanning electron microscopy, and photoluminescence spectroscopy were used to characterize the as-prepared samples. The Sr_2MgAl_2_2O_3_6:Tb"3"+ phosphors show intense green light emission under UV excitation. The phosphor exhibit two groups of emission lines from about 370 to 700 nm, which originating from the characteristic "5D_3-"7F_J and "5D_4-"7F_J transitions of the Tb"3"+ ion, respectively. The cross-relaxation mechanism between the "5D_3 and "5D_4 emission was investigated and discussed. The emission colors of these phosphors can be tuned from bluish-green to green by adjusting the Tb"3"+ doping concentration. Furthermore, the thermal quenching temperature (T_1_/_2) is higher than 500 K. The excellent thermal stability and color-tunable luminescent properties suggest that the developed material is a promising green-emitting phosphor candidate for optical devices. - Highlights: • A Color-tunable emitting phosphor Sr_2MgAl_2_2O_3_6:Tb"3"+ was prepared successfully via high-temperature solid-state reaction. • The photoluminescence of Sr_2MgAl_2_2O_3_6:Tb"3"+ shows highly thermal stable. • The cross-relaxation mechanism between the "5D_3 and "5D_4 emission was investigated and discussed.

Photoluminescence spectroscopies and temperature-dependent luminescence of Mn{sup 4+} in BaGe{sub 4}O{sub 9} phosphor

Energy Technology Data Exchange (ETDEWEB)

Zhang, Shaoan; Hu, Yihua, E-mail: huyh@gdut.edu.cn

2016-09-15

New non-rare-earth red phosphor BaGe{sub 4}O{sub 9}:Mn{sup 4+} was prepared successfully via the traditional solid state reaction method. The luminescent performance was investigated by the steady-state photoluminescence (PL) and temperature-dependent PL/decay measurements. The excitation band of BaGe{sub 4}O{sub 9}:Mn{sup 4+} phosphor covers a broad spectral region from 250 nm to 500 nm, which matches well with the commercial near-UV and blue LEDs. The concentration quenching of Mn{sup 4+} in BaGe{sub 4}O{sub 9}:Mn{sup 4+} occurs at a low content of 0.5% due to the dipole–dipole interaction. We gained insight into the temperature-dependent relative emission intensity of BaGe{sub 4}O{sub 9}:Mn{sup 4+} phosphor, and determined the luminescence quenching temperature and the activation energy for thermal quenching (∆E) to be ~150 K and ~0.17 eV, respectively.

An open aperture z-scan study of Sr2CeO4 blue phosphor

International Nuclear Information System (INIS)

Seema, R.; Sandeep, C.S. Suchand; Philip, Reji; Kalarikkal, Nandakumar

2011-01-01

Highlights: → Sr 2 CeO 4 blue phosphor has been prepared by a solid state reaction method. → The XRD study confirms that the structure of the system is orthorhombic. → The TEM reveals that Sr 2 CeO 4 is composed of elongated spherical structures of length ∼0.2-0.6 μm. → The FFT of TEM, XRD peaks and the JCPDS values are compared, from which the Sr 2 CeO 4 phase is reconfirmed. → A z-scan measurement gives the effective two-photon absorption coefficient to be 3.9 x 10 -11 m/W. - Abstract: Sr 2 CeO 4 blue phosphor has been prepared by the solid-state reaction method. The X-ray diffraction (XRD) study confirms the structure of the system to be orthorhombic. High resolution electron transmission microscopy reveals that Sr 2 CeO 4 prepared by the solid state reaction method is composed of elongated spherical structures of length ∼0.2-0.6 μm and width ∼90-150 nm. The excitation spectrum shows a broad band which peaks at 275 nm. The emission spectrum shows a broad band which peaks at 467 nm when excited at 275 nm. The emission band is assigned to the energy transfer between the molecular orbital of the ligand and charge transfer (CT) state of the Ce 4+ ion. The Commission International de l'Eclairage (CIE) co-ordinates are x = 0.15, and y = 0.23. The nonlinear absorption behavior of Sr 2 CeO 4 has been investigated using the open aperture z-scan technique. The calculated effective two-photon absorption coefficient shows that the Sr 2 CeO 4 blue phosphor is a promising optical limiting material.

Luminescence properties of red-emitting M2Si5N8:Eu2+ (M = Ca, Sr, Ba) LED conversion phosphors

NARCIS (Netherlands)

Li, Y.Q.; Steen, van J.E.J.; Krevel, van J.W.H.; Botty, G.; Delsing, A.C.A.; DiSalvo, F.J.; With, de G.; Hintzen, H.T.J.M.

2006-01-01

The influence of the type of the alkaline-earth ion and the Eu2+ concentration on the luminescence properties of Eu2+-doped M2Si5N8 (M = Ca, Sr, Ba) has been investigated. XRD analysis shows that Eu2+-doped Ca2Si5N8 forms a limited solid solution with a maximum solubility of about 7 mol% having a

Hexagonal perovskites with cationic vacancies. 32. Photoluminescence of trivalent rare earth in the systems Ba/sub 2-y/Sr/sub y/La/sub 2-x/RE/sub x/MgW/sub 2/vacantO/sub 12/

Energy Technology Data Exchange (ETDEWEB)

Kemmler-Sack, S [Tuebingen Univ. (Germany, F.R.). Lehrstuhl fuer Anorganische Chemie 2

1982-06-01

In the series Ba/sub 2-y/Sr/sub y/La/sub 2-x/RE/sub x/MgW/sub 2/vacantO/sub 12/ the Ba/sup 2 +/ can be completely substituted by Sr/sup 2 +/. All compounds crystallize in the rhombohedral 12 L-type (space group R-3m; sequence (hhcc)/sub 3/). By doping the stacking polytypes with some of the trivalent rare earths efficient visible photoluminescence is obtained. The simultaneous incorporation of two different rare earth ions leads to two-color-phosphors, which, according to the excitation energy used, emit either mainly the typical spectrum from one or the other activator; the corresponding luminescence mechanism are discussed.

Heat capacity measurement of Ba3SrNb2O9

International Nuclear Information System (INIS)

Singh, B.M.; Samui, Pradeep; Agarwal, Renu; Mukerjee, S.K.

2016-01-01

Barium, Strontium and Niobium are important fission products in nuclear reactor with reasonable fission yields. During irradiation of oxide fuels, they can combine to form compounds of Ba-Sr-Nb-O system. Therefore, thermodynamic properties of Ba 3 SrNb 2 O 9 are required for modelling fuel behaviour however thermodynamic data of this compound is not available in literature. Ba 3 SrNb 2 O 9 was prepared by solid state route, by mixing stoichiometric amounts of finely grounded SrCO 3 , BaCO 3 and Nb 2 O 5 . Finally mixed powder was pressed into a pellet at 5 ton pressure for 2 minutes in a hydraulic press and the pellet was heated at 1123 K for 60 h in air. The pellet was cooled, finely grounded, re-pelletised and heated at 1473 K for 120 h. The formation of compound was confirmed by X-ray diffraction pattern, collected at room temperature using Cu-K α radiation (λ = 1.54 nm), scanned over the angular range 20-80° (2θ) with steps of 0.02°. Heat capacity of the compound was measured by the classical three-step method, in continuous mode, using LABSYS EVO, in temperature range of 370 and 950 K. No transition was observed in the investigated temperature range

Physical and magnetic properties of (Ba/Sr) substituted magnesium nano ferrites

Science.gov (United States)

Ateia, Ebtesam E.; Takla, E.; Mohamed, Amira T.

2017-10-01

In the presented paper, strontium (Sr) and barium (Ba) nano ferrites were synthesized by citrate auto combustion method. The investigated samples are characterized by X-ray diffraction technique (XRD), field emission scanning electron microscopy, high resolution transmission electron microscopy and energy dispersive X-ray spectroscopy. The structural properties of the obtained samples were examined by XRD analysis showing that the synthesized nanoparticles are in cubic spinel structure. The average crystallite sizes are in the range of 22.66 and 21.95 nm for Mg0.7Ba0.3Fe2O4 and Mg0.7 Sr0.3Fe2O4 respectively. The VSM analysis confirms the existence of ferromagnetic nature of Sr2+/Ba2+ substituted magnesium nano particles. Exchange interaction between hard (Sr/Ba) and soft (Mg) magnetic phases improves the structural and magnetic properties of nano ferrite particles. Rigidity modulus, longitudinal and shear wave velocities are predicted theoretically from Raman spectroscopy and structural data of the investigated spinel ferrite. The magnetic and structural properties of magnesium are enhanced by doping with barium and strontium nano particles. The saturation magnetization, remanent magnetization and coercivity reported on vibrating sample magnetometer curve illustrate the promising industrial and magnetic recording applications of the prepared samples.

Computational study of Ca, Sr and Ba under pressure

International Nuclear Information System (INIS)

Jona, F; Marcus, P M

2006-01-01

A first-principles procedure for the calculation of equilibrium properties of crystals under hydrostatic pressure is applied to Ca, Sr and Ba. The procedure is based on minimizing the Gibbs free energy G (at zero temperature) with respect to the structure at a given pressure p, and hence does not require the equation of state to fix the pressure. The calculated lattice constants of Ca, Sr and Ba are shown to be generally closer to measured values than previous calculations using other procedures. In particular for Ba, where careful and extensive pressure data are available, the calculated lattice parameters fit measurements to about 1% in three different phases, both cubic and hexagonal. Rigid-lattice transition pressures between phases which come directly from the crossing of G(p) curves are not close to measured transition pressures. One reason is the need to include zero-point energy (ZPE) of vibration in G. The ZPE of cubic phases is calculated with a generalized Debye approximation and applied to Ca and Sr, where it produces significant shifts in transition pressures. An extensive tabulation is given of structural parameters and elastic constants from the literature, including both theoretical and experimental results

Computational study of Ca, Sr and Ba under pressure

Energy Technology Data Exchange (ETDEWEB)

Jona, F; Marcus, P M [Department of Materials Science and Engineering, State University of New York, Stony Brook, NY 11794-2275 (United States)

2006-05-17

A first-principles procedure for the calculation of equilibrium properties of crystals under hydrostatic pressure is applied to Ca, Sr and Ba. The procedure is based on minimizing the Gibbs free energy G (at zero temperature) with respect to the structure at a given pressure p, and hence does not require the equation of state to fix the pressure. The calculated lattice constants of Ca, Sr and Ba are shown to be generally closer to measured values than previous calculations using other procedures. In particular for Ba, where careful and extensive pressure data are available, the calculated lattice parameters fit measurements to about 1% in three different phases, both cubic and hexagonal. Rigid-lattice transition pressures between phases which come directly from the crossing of G(p) curves are not close to measured transition pressures. One reason is the need to include zero-point energy (ZPE) of vibration in G. The ZPE of cubic phases is calculated with a generalized Debye approximation and applied to Ca and Sr, where it produces significant shifts in transition pressures. An extensive tabulation is given of structural parameters and elastic constants from the literature, including both theoretical and experimental results.

Synthesis, luminescent properties and white light emitting diode application of Ba{sub 7}Zr(PO{sub 4}){sub 6}:Eu{sup 2+} yellow-emitting phosphor

Energy Technology Data Exchange (ETDEWEB)

Li, Chenxia; Dai, Jian [College of Optical and Electronic Technology, China Jiliang University, Hangzhou 310018 (China); Deng, Degang, E-mail: dengdegang@cjlu.edu.cn [College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Shen, Changyu [College of Optical and Electronic Technology, China Jiliang University, Hangzhou 310018 (China); Xu, Shiqing, E-mail: sxucjlu@163.com [College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China)

2015-10-15

A yellow-emitting phosphor, Eu{sup 2+}-activated Ba{sub 7}Zr(PO{sub 4}){sub 6} phosphor was synthesized by solid-state reaction method and the luminescence properties were investigated. The phosphor exhibited strong absorption in near ultraviolet (n-UV) region, which matched well with the n-UV chip. Upon excitation at 370 nm, the Ba{sub 7}Zr(PO{sub 4}){sub 6}:Eu{sup 2+} phosphor has a broad yellow emission band with a peak at 585 nm and a full width at half maximum of 178 nm wider than that of the commercial yellow-emitting YAG:Ce{sup 3+} phosphor. The mechanism of concentration quenching of Eu{sup 2+} ions in Ba{sub 7}Zr(PO{sub 4}){sub 6} phosphor is verified to be energy transfer among the nearest neighbor Eu{sup 2+} ions. The CIE value and temperature dependence of photoluminescence were also discussed. Furthermore, a white-LED was fabricated using a 370 nm UV chip pumped with a blend of phosphors consisting of yellow-emitting Ba{sub 6.97}Zr(PO{sub 4}){sub 6}:0.03Eu{sup 2+} and blue-emitting BaMgAl{sub 10}O{sub 17}:Eu{sup 2+} phosphors, which achieved a CIE of (0.3329, 0.3562) with a color-rendering index of 86.4 around the CCT of 5487 K.

Impedance spectroscopy of Li2CO3 doped (Ba,Sr)TiO3 ceramic

Science.gov (United States)

Ham, Yong-Su; Koh, Jung-Hyuk

2013-02-01

(BaxSr1-x)TiO3-based ceramic has been considered as one of the most important electronic materials widely employed in microwave passive device applications. Many researches have been performed to lower the high sintering temperature, by adding various dopants such as B2O3, La2O3, etc. In our previous study, by adding Li2CO3 to (Ba0.5,Sr0.5)TiO3 ceramics, the sintering temperature of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics decreased from 1350 to 900 °C. This study observed the crystalline structure and electrical properties of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics. In scanning the crystalline structure of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics, no pyro phase was observed by X-ray diffraction analysis. To investigate the electrical properties of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics, real and imaginary parts of the impedances were analyzed. Complex impedance data were measured from 100 Hz to 1 MHz at various temperature ranges.

Sequential separation of cs, ca and ba for 90sr assessment

International Nuclear Information System (INIS)

Dianu, M.; Bucur, C.

2015-01-01

A two-steps chemical treatment technique for strontium assessment from aqueous samples is described in this paper. The method was applied to simulated samples containing stable elements of Ni, Cs, Ca, Ba, Mn, Fe, Co and Eu. The transition elements (Ni, Mn, Fe, Co, Eu) were precipitated as hydroxides, followed by alkaline-earth metals separation (Ca, Ba) as carbonates. Finally, the Sr was purified by extraction chromatography using Triskem International Sr resin. The strength of Sr sorption in nitric acid increases with increasing acid concentration, and the optimal bonding strength is achieved in 8 M HNO3. The combination of successive precipitations with extraction chromatography for complete removal of other interferences from Sr matrix leads to good recovery and decontamination factor values. (authors)

Luminescent characteristics of UV excited Sr_0_._5Ca_0_._5TiO_3: Pr"3"+ reddish-orange phosphor

International Nuclear Information System (INIS)

Vidyadharan, Viji; Mohan P, Remya; Joseph, Cyriac; Unnikrishnan, N.V.; Biju, P.R.

2016-01-01

Pr"3"+ doped Sr_0_._5Ca_0_._5TiO_3 phosphors were synthesised by solid state reaction process. The structure, surface morphology and photoluminescence of the prepared phosphors were analysed using XRD, SEM and photoluminescence spectroscopy respectively. The XRD pattern confirmed orthorhombic perovskite structure of the Sr_0_._5Ca_0_._5TiO_3: x Pr"3"+ phosphor. Agglomeration of particles with irregular shapes is observed from the SEM images. The emission spectra of Sr_0_._5Ca_0_._5TiO_3: x Pr"3"+ phosphor shows the samples can be effectively excited with UV light at 336 nm and exhibit a strong reddish-orange emission at 611 nm. Concentration dependence of emission intensity shows concentration quenching effect on increasing Pr"3"+ concentration after x = 0.1 because of dipole–dipole interaction. Using Blasse's formula, critical distance for energy transfer was calculated. The CIE co-ordinates, CCT, colour purity and luminescence decay of the prepared phosphors were also calculated. These results offer the prepared phosphor as a suitable candidate for various photonic applications. - Highlights: • Sr_0_._5Ca_0_._5TiO_3: x Pr"3"+ perovskite structured phosphors were synthesized. • Under UV excitation, the PL spectra show strong reddish-orange emission. • The emission from "3P_J levels of Pr"3"+ were absent due to the presence of IVCT band. • Concentration quenching due to dipole–dipole interaction was observed. • For x = 0.1, sample shows a maximum emission intensity with 91.7% colour purity.

Li4SrCa(SiO4)2:Ce3+, a highly efficient near-UV and blue emitting orthosilicate phosphor

International Nuclear Information System (INIS)

Zhang, Jilin; Zhang, Weilu; Qiu, Zhongxian; Zhou, Wenli; Yu, Liping; Li, Zhiqiang; Lian, Shixun

2015-01-01

High quantum efficiency is a vital parameter of phosphors for practical application. An efficient near-UV and blue emitting phosphor Li 4 SrCa(SiO 4 ) 2 :Ce 3+ was synthesized by a traditional solid-state reaction, and luminescent properties were studied in detail. The Ce 3+ -activated phosphor can emit both a near-UV light centred at 345 nm and a blue light peaking at 420 nm when Ce 3+ occupies the Sr and Ca site, respectively. The internal quantum efficiency (IQE) of Li 4 SrCa(SiO 4 ) 2 :0.03Ce 3+ is as high as 97% under the excitation at 288 nm, while the external quantum efficiency (EQE) is 66%. The IQE and EQE values of Li 4 SrCa(SiO 4 ) 2 :0.03Ce 3+ under the excitation at 360 nm are 82% and 31%, respectively. - Highlights: • Phosphor Li 4 SrCa(SiO 4 ) 2 :Ce 3+ emits a near-UV (345 nm) and a blue light (420 nm). • Emission band at 345 nm originates from Ce 3+ on Sr site. • Emission band at 420 nm belongs to Ce 3+ on Ca site. • Internal quantum efficiency is 97% for Li 4 SrCa(SiO 4 ) 2 :0.03Ce 3+ excited at 288 nm

Photoluminescence and thermoluminescence properties of Eu2+ doped and Eu2+ ,Dy3+ co-doped Ba2 MgSi2 O7 phosphors.

Science.gov (United States)

Sao, Sanjay Kumar; Brahme, Nameeta; Bisen, D P; Tiwari, Geetanjali

2016-11-01

In this work, we report the preparation, characterization, comparison and luminescence mechanisms of Eu 2 + -doped and Eu 2 + ,Dy 3 + -co-doped Ba 2 MgSi 2 O 7 (BMSO) phosphors. Prepared phosphors were synthesized via a high temperature solid-state reaction method. All prepared phosphors appeared white. The phase structure, particle size, and elemental analysis were analyzed using X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy-dispersive X-ray (EDX) analysis. The luminescence properties of the phosphors were investigated by thermoluminescence (TL) and photoluminescence (PL). The PL excitation and emission spectra of Ba 2 MgSi 2 O 7 :Eu 2 + showed the peak to be around 381 nm and 490 nm respectively. The PL excitation spectrum of Ba 2 MgSi 2 O 7 :Eu 2 + Dy 3 + showed the peak to be around 341 nm and 388 nm, and the emission spectrum had a broad band around 488 nm. These emissions originated from the 4f 6 5d 1 to 4f 7 transition of Eu 2 + . TL analysis revealed that the maximum TL intensity was found at 5 mol% of Eu 2 + doping in Ba 2 MgSi 2 O 7 phosphors after 15 min of ultraviolet (UV) light exposure. TL intensity was increased when Dy 3 + ions were co-doped in Ba 2 MgSi 2 O 7 :Eu 2 + and maximum TL intensity was observed for 2 mol% of Dy 3 + . TL emission spectra of Ba 1.95 MgSi 2 O 7 :0.05Eu 2 + and Ba 1.93 MgSi 2 O 7 :0.05Eu 2 + ,0.02Dy 3 + phosphors were found at 500 nm. TL intensity increased with UV exposure time up to 15 min, then decreased for the higher UV radiation dose for both Eu doping and Eu,Dy co-doping. The trap depths were calculated to be 0.54 eV for Ba 1.95 MgSi 2 O 7 :0.05Eu 2 + and 0.54 eV and 0.75 eV for Ba 1.93 MgSi 2 O 7 :0.05Eu 2 + ,0.02Dy 3 + phosphors. It was observed that co-doping with small amounts of Dy 3 + enhanced the thermoluminescence properties of Ba 2 MgSi 2 O 7 phosphor. Copyright © 2016 John Wiley & Sons, Ltd. [Correction added on 5 April 2016, after first online publication: The

Persistent luminescence and thermoluminescence of UV/VIS -irradiated SrAl2O4: Eu2+, Dy3+ phosphor

International Nuclear Information System (INIS)

Pereyda-Pierre, C.; Meléndrez, R.; García, R.; Pedroza-Montero, M.; Barboza-Flores, M.

2011-01-01

The persistent luminescence and thermoluminescence properties of SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphors excited with UV–VIS light in the 200–500 nm region were investigated. The thermoluminescence glow curve was found to be composed of peaks around 70, 125 and 245 °C. The persistent luminescence and thermoluminescence excitation spectra exhibited a broad band around 300–500 nm centered at 400 and 420 nm respectively. A linear behavior of the integrated thermoluminescence intensity and persistent luminescence versus irradiation time was found for the first 60 s. The charge detrapping from the 70 °C trapping levels was the major contributor to the observed persistent luminescence at room temperature. The SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphors have suitable properties to be applied as storage and persistent luminescence UV–VIS irradiation dose phosphor. -- Highlights: ► SrAl 2 O 4 :Eu 2+ , Dy 3+ persistent luminescence and thermoluminescence was measured. ► The phosphor was irradiated with UV–VIS photons in the 200–500 nm wavelength range. ► SrAl 2 O 4 :Eu 2+ , Dy 3+ behaves adequately as persistent and storage UV–VIS dosimeter. ► The persistent luminescence dosimetry does not require heat or light stimulation.

Mechanistic model for Sr and Ba release from severely damaged fuel

International Nuclear Information System (INIS)

Rest, J.; Cronenberg, A.W.

1985-11-01

Among radionuclides associated with fission product release during severe accidents, the primary ones with health consequences are the volatile species of I, Te, and Cs, and the next most important are Sr, Ba, and Ru. Considerable progress has been made in the mechanistic understanding of I, Cs, Te, and noble gas release; however, no capability presently exists for estimating the release of Sr, Ba, and Ru. This paper presents a description of the primary physical/chemical models recently incorporated into the FASTGRASS-VFP (volatile fission product) code for the estimation of Sr and Ba release. FASTGRASS-VFP release predictions are compared with two data sets: (1) data from out-of-reactor induction-heating experiments on declad low-burnup (1000 and 4000 MWd/t) pellets, and (2) data from the more recent in-reactor PBF Severe Fuel Damage Tests, in which one-meter-long, trace-irradiated (89 MWd/t) and normally irradiated (approx.35,000 MWd/t) fuel rods were tested under accident conditions. 10 refs

Structural characterization and optical properties of Eu"2"+ and Dy"2"+ doped Sr_2SiO_4 phosphor by solid state reaction method

International Nuclear Information System (INIS)

Verma, Durga; Verma, Mohan L.; Upma; Patel, R.P.

2016-01-01

Thermoluminescence, SEM, FTIR Divalent dysprosium and europium doped strontium silicate (Sr_2SiO_4) phosphors were synthesized with the high-temperature solid-state reaction technique. The obtained phosphor was well characterized by powder X-ray diffraction, scanning electron microscopy, FTIR, UV-visible spectroscopy and thermoluminescence. The crystal structure of the prepared phosphor has an orthorhombic structure with space group Pnma. From scanning electron microscopy (SEM), agglomerations of particles were observed due to the high temperature synthesis process. The chemical composition of the sintered Sr_2SiO_4:Dy"2"+ and Sr_2SiO_4: Eu"2"+ phosphor was confirmed by energy dispersive X-ray spectroscopy (EDX). The UV-VIS analysis can be thought as a good quality check for the optical behavior of materials. The Fourier transmission infrared spectroscopy (FTIR) confirms the present elements in phosphor. Thermoluminescence study was carried out for the phosphor with UV irradiation show one glow peak. The trapping parameters associated with the prominent glow peak of Sr_2SiO_4:Dy"2"+ and Sr_2SiO_4:Eu"2"+ are calculated using Chen's glow curve method. The release of holes/electrons from defect centers at the characteristic trap site initiates the luminescence process in this material. (author)

The effect of diameter ratio between transducers and reactor in sonication-assisted synthesis of Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Manaf, A., E-mail: azwar@ui.ac.id; Fahmi, Agam Aidil [Department of Physics, FMIPA, Universitas Indonesia, Kampus UI Depok (Indonesia); Yustanti, Erlina [Department of Physics, FMIPA, Universitas Indonesia, Kampus UI Depok (Indonesia); Department of Metallurgy, Faculty of Engineering, University of Sultan AgengTirtayasa Jl. Jenderal Sudirman KM 03 Cilegon-Banten 65134 (Indonesia)

2016-04-19

This paper describes the particle size characterization of mechanically alloyed Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} prepared with the aid of a high-power ultrasonic destruction. Analytical-grade BaCO{sub 3}, TiO{sub 2} and SrCO{sub 3} with a purity greater than 99 wt.% were used as precursors for Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3}. The mechanically powders were respectively sintered at 1200 °C for 3 hours to form crystalline powders. This work is aimed at studying the effect of diameter ratio between reactor and transducer of a high power sonicator on the Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} nanoparticles formation. The presence of a single phase of the two materials was confirmed by X-Ray Diffraction (XRD). The concentration of the particles in demineralized water was 3.0 g / 100 mL which become the object of 3 hours ultrasonic destruction subjected to the application of transducer in which the ratio between the diameter of the reactor and the transducer (D/d) was fixed at 1.4, 1.6 and 1.8 respectively. It was found that the mean particle size before the ultrasonic destruction was 538 nm for Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and 480 nm for Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3}. With D/d of 1.8, the mean particle size of the two materials was found to decrease drastically to 38 nm and 24 nm, respectively. These mean particle sizes were respectively comparable with that of the crystallite size of the particles derived using the Whole Powder Pattern Modelling (WPPM) from which the mean crystallite size of 22 nm for Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and 14 nm for Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} were obtained. It is then confirmed single nanocrystallite Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} particles were already achieved. We can conclude that the ultrasonic destruction to mechanically milled crystalline particles would be one

Synthesis and optical properties of red/blue-emitting Sr2MgSi2O7:Eu3+/Eu2+ phosphors for white LED

Directory of Open Access Journals (Sweden)

Tong Thi Hao Tam

2016-06-01

Full Text Available Phosphor-converted white light emitting diodes (white LEDs have received great attention in recent years since they have several excellent features such as high lumen output, low power consumption, long lifetime and environmentally friendly. In this work, we report the co-precipitation synthesis of red/blue Sr2MgSi2O7:Eu3+/Eu2+ phosphors with various Eu doping concentration. The results show that the obtained Sr2MgSi2O7:Eu3+/Eu2+ phosphors have good crystallinity and emit strong red (Sr2MgSi2O7:Eu3+ and blue (Sr2MgSi2O7:Eu2+ emissions under near UV light excitation. The sharp emission peaks at 577, 590, 612, 653, and 701 nm corresponded to the typical 5D0 → 7Fj (j = 0,1,2,3,4 transitions of Eu3+, and the blue emission peaking at 460 nm is attributed to the typical 4f65d1-4f7 transition of Eu2+ in the same Sr2MgSi2O7 host lattice. Both phosphors can be well excited in the wavelength range of 260–400 nm where the near UV-LED is well matched. The above results suggest that the Sr2MgSi2O7:Eu3+/Eu2+ phosphors are promising red/blue-emitting phosphors for the application in near UV pumped phosphor-converted white LEDs.

A novel double perovskite tellurate Eu3+-doped Sr2MgTeO6 red-emitting phosphor with high thermal stability

Science.gov (United States)

Liang, Jingyun; Zhao, Shancang; Yuan, Xuexia; Li, Zengmei

2018-05-01

A series of novel double perovskite tellurate red-emitting phosphors Sr2MgTeO6:xEu3+ (x = 0.05-0.40) were successfully synthesized by a high-temperature solid-state reaction method. The phase structure, photoluminescence properties and thermal stability of the phosphor were investigated in detail. The phosphor shows dominant emission peak at 614 nm belonging to the 5D0 → 7F2 electric dipole transition under 465 nm excitation. The luminescence intensity keeps increasing with increasing the content of Eu3+ to 25 mol%, and the critical transfer distance of Eu3+ was calculated to be 12 Å. The quenching temperature for Sr2MgTeO6:0.25Eu3+ was estimated to be above 500 K. This spectral feature reveals high color purity and excellent chromaticity coordinate characteristics. Therefore, Eu3+-doped Sr2MgTeO6 phosphors are potential red phosphors for blue chip-based white light-emitting diode and display devices.

Acetate reduction synthesis of Sr2Si5N8:Eu2+ phosphor and its luminescence properties

International Nuclear Information System (INIS)

Piao Xianqing; Machida, Ken-ichi; Horikawa, Takashi; Yun Bonggoo

2010-01-01

A novel synthesis method was developed for the efficient red phosphor, Eu 2+ -activated Sr 2 Si 5 N 8 , by employing the strontium acetate as both the reducing agent and strontium source. The phase purity of final product was strongly dependent on the heating rate of the precursors. Sr 2 Si 5 N 8 :Eu 2+ (2 at%) phosphor presented a broadband excitation spectrum in the range 300-500 nm, matching well with the blue emission (400/460 nm) of current InGaN light-emitting diodes (LEDs). The red emission peaking at 619 nm gave the relatively high (about 155%) intensity compared with the Y 3 Al 5 O 12 (YAG) (P46-Y3) standard phosphor. In addition, the saturated chromatic coordinates (0.638, 0.359) allowed it a promising candidate as a red phosphor in white LEDs application for illumination or display.

Synthesis and photoluminescence properties of Ba2CaZn2Si6O17:Eu3+ red phosphors for white LED applications

International Nuclear Information System (INIS)

Annadurai, G.; Kennedy, S. Masilla Moses

2016-01-01

Novel pellyite type Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ red emitting phosphors with different Eu 3+ contents were synthesized by the solid state reaction method. The crystal structure, photoluminescence properties and concentration quenching of Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ phosphors were investigated. Powder X-ray diffraction measurements confirmed the structure of the samples. The photoluminescence emission (PL) and excitation (PLE) spectra were measured. The results showed that the dominant hypersensitive red emission peak of the phosphors Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ was located at 613 nm attributed to the Eu 3+ transition ( 5 D 0 → 7 F 2 ) which could be effectively excited by 395 nm (near-UV). The latter band matched well with the emission from the near-UV LED chips. The intensity ratio of 5 D 0 → 7 F 2 to 5 D 0 → 7 F 1 transition showed slight variation with Eu 3+ concentrations. The Eu 3+ emission intensity was maximum for 9 mol%. The luminescence quantum efficiency was determined and also the decay profiles were obtained and analyzed. In addition, the Commission International del'Eclairage (CIE) chromaticity coordinates of Ba 2 CaZn 2 Si 6 O 17 :0.09Eu 3+ phosphor were calculated to be 0.637 and 0.362. The experimental results demonstrated that the Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ red emitting phosphor is a potential candidate for white light emitting diodes (WLEDs) pumped by near-UV chip. - Highlights: • A novel Ba 2 CaZn 2 Si 6 O 17 :Eu 3+ red phosphor was synthesized. • The samples yielded a dominant PL emission of Eu 3+ at 613 nm. • Eu 3+ concentration was optimized to be 9 mol% in Ba 2 CaZn 2 Si 6 O 17. • CIE chromaticity coordinates were estimated from the emission spectrum.

Consideration of the band-gap tunability of BaSi2 by alloying with Ca or Sr based on the electronic structure calculations

International Nuclear Information System (INIS)

Imai, Yoji; Watanabe, Akio

2007-01-01

The electronic structures and total energies of BaSi 2 -SrSi 2 and BaSi 2 -CaSi 2 systems have been calculated using the first-principle pseudopotential method to clarify the band gap tunability of BaSi 2 by alloying with Sr or Ca. From an energetic consideration of the compounds where all the Ba I sites or all the Ba II sites of the BaSi 2 lattice are preferentially replaced by Sr or Ca, it is expected that the Ba I site will be preferentially replaced by Sr rather than the Ba II sites. Compounds where all the Ba II sites are replaced by Sr or all the Ba II or all the Ba I sites are replaced by Ca are energetically unfavorable compared to the undissolved system of BaSi 2 and SrSi 2 or CaSi 2 . The effect of the addition of Sr or Ca into the BaSi 2 lattice on the gap value is different depending on the replaced sites of Ba. The replacement of Ba I site by Sr will broaden the band gap of BaSi 2 , which is consistent with the observed results

First-principles study of the (001) surface of cubic Ba0.5Sr0.5TiO3

International Nuclear Information System (INIS)

Wang, Yuan Xu

2008-01-01

We have theoretically investigated basic properties of the (001) surface of cubic Ba 0.5 Sr 0.5 TiO 3 (BST) by the plane-wave pseudopotential method within the local-density approximation. For the BaSrO 2 -terminated surface, the surface-layer Sr atoms move inward and the surface-layer Ba atoms move outward. Moreover, the displacement of the surface-layer Sr atoms is much larger than the surface-layer Ba atoms. The rumpling of the BaSrO 2 -terminated surface is much larger than that of the Ti 2 O 4 -terminated one. The surface state appears in the band structure of the Ti 2 O 4 -terminated surface of BST. Based on the results of the calculated grand thermodynamic potential, only the BaSrO 2 -terminated surface can exist in the (001) surface of cubic BST. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Tunable luminescence properties and energy transfer in Ba{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+},Tb{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Jin, Cheng [Department of Physics and Electronic Engineering, Baoding University, Baoding 071002 (China); Ma, Hengxin [College of Science, Agricultural University of Hebei, Baoding 071002 (China); Liu, Yufeng, E-mail: liuyufeng4@126.com [State Key Lab of Power Systems, Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China); Liu, Qingbo [Department of Physics and Electronic Engineering, Baoding University, Baoding 071002 (China); Dong, Guoyi [College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Yu, Quanmao [Institute of Functional Materials, Jiangxi University of Finance and Economics, Nanchang 330013 (China)

2014-11-15

Highlights: • Effective energy transfer from Ce{sup 3+} to Tb{sup 3+} in Ba{sub 3}Lu(PO{sub 4}){sub 3} was confirmed. • The reason of energy transfer from Ce{sup 3+} to Tb{sup 3+} was investigated in detail. • Ba{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} can be a potential green-emitting phosphor for UV LEDs. - Abstract: A series of novel color-tunable phosphors Ba{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+},Tb{sup 3+} have been synthesized by solid-state reaction. X-ray diffraction, photoluminescence emission and excitation spectra, lifetime, as well as the effect of Tb{sup 3+} concentration were employed to characterize the resulting samples. The emission spectra of Ba{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+},Tb{sup 3+} phosphor contains both the asymmetric broad-band Ce{sup 3+} ion emission and the line-type Tb{sup 3+} ion emission. Under ultraviolet light excitation, Ba{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+},Tb{sup 3+} can achieve tunable emission from deep blue to yellowish-green by changing the concentration of Tb{sup 3+}. The results indicated that these phosphors could be considered as double emission phosphors for field emission displays.

Luminescent properties of red-emitting LiSr4B3O(9−3x/2)Nx:Eu2+ phosphor for white-LEDs

International Nuclear Information System (INIS)

Yu Hua; Deng Degang; Xu Shiqing; Yu Cuiping; Yin Haoyong; Nie Qiulin

2012-01-01

An Eu 2+ -activated oxynitride LiSr (4−y) B 3 O (9−3x/2) N x :yEu 2+ red-emitting phosphor was synthesized by solid-state reactions. The synthesized phosphor crystallized in a cubic system with space group Ia–3d. The LiSr 4 B 3 O (9−3x/2) N x :Eu 2+ phosphors exhibited a broad red emission band with a peak at 610 nm and a full width at half maximum of 106 nm under 410 nm excitation, which is ascribed to the 4f 6 5d 1 →4f 7 transition of Eu 2+ . The optimal doped nitrogen concentration was observed to be x=0.75. The average decay times of two different emission centers were estimated to be 568 and 489 ns in the LiSr 3.99 B 3 O 8.25 N 0.5 :0.01Eu 2+ phosphors, respectively. Concentration quenching of Eu 2+ ions occurred at y=0.07, and the critical distance was determined as 17.86 Å. The non-radiative transitions via dipole–dipole interactions resulted in the concentration quenching of Eu 2+ -site emission centers in the LiSr 4 B 3 O 9 host. These results indicate LiSr 4 B 3 O (9−3x/2) N x :Eu 2+ phosphor is promising for application in white near-UV LEDs. - Highlights: ► An oxynitride LiSr 4 B 3 O 9 N:Eu 2+ red-emitting phosphor was prepared at low synthesis temperature. ► The introduced nitrogen improved the excitation and emission intensity of the phosphor. ► The wide excitation band matches well with near-UV LED chips. ► The emission spectrum of the phosphor showed a broad full width at half maximum of about 106 nm.

Orthorhombic strontium titanate in BaTiO sub 3 -SrTiO sub 3 superlattices

CERN Document Server

Rios, S; Jiang, A Q; Scott, J F; Lü, H; Chen, Z

2003-01-01

It has been suggested by several authors that SrTiO sub 3 layers in SrTiO sub 3 -BaTiO sub 3 superlattices should be tetragonal and ferroelectric at ambient temperatures, like the BaTiO sub 3 layers, rather than cubic, as in bulk SrTiO sub 3 , and that free-energy minimization requires continuity of the polarization direction. A recent ab initio calculation constrained solutions to this structure. Surprisingly, our x-ray study shows that the SrTiO sub 3 layers are orthorhombic with 0.03% in-plane strain, with the BaTiO sub 3 c-axis matching the SrTiO sub 3 a- and b-axis better than the c-axis; strain energy overcomes the cost in electrostatic energy. (letter to the editor)

LiSr4(BO3)3:Ce3+ phosphor as a new material for ESR dosimetry

International Nuclear Information System (INIS)

Jiang, L.H.; Zhang, Y.L.; Gong, X.M.; Pang, R.; Zhang, S.; Li, C.Y.; Su, Q.

2014-01-01

LiSr 4 (BO 3 ) 3 :0.01Ce 3+ phosphor was investigated to assess its potential as a material for measurements of radiotherapeutic doses with electron spin resonance (ESR). The ESR spectrum of the phosphor irradiated with 60 Co features five ESR signals. An isochronal annealing experiment has shown that the strongest of these signals is associated with the same trap center as the 473 K peak on the TL glow curve of this material. The dose–response is linear in the studied range from 0.89 to 90.30 Gy. Fading of the signal was also investigated. - Highlights: • LiSr 4 (BO 3 ) 3 :Ce 3+ phosphor can be used as an ESR dosimeter for radiation therapy. • The ESR signal originates from the same traps as the TL. • Dose–response is linear, and the fading is slow

Microstructure and dielectric parameters of epitaxial SrRuO3/BaTiO3/SrRuO3 heterostructures

Science.gov (United States)

Boikov, Yu. A.; Claeson, T.

2001-05-01

Epitaxial films of ferroelectric barium titanate are desirable in a number of applications but their properties are inferior to those of bulk material. Relations between microstructure and dielectric properties may give better understanding of limitations. Trilayer heterostructures SrRuO3/BaTiO3/SrRuO3 were grown by laser ablation on (100)LaAlO3 and (100)MgO substrates. The BaTiO3 layer was granular in structure. When grown on (100)SrRuO3/(100)LaAlO3, it was preferentially a-axis oriented due to tensile mechanical stress. Using (100)MgO as a substrate, on the other hand, produced a mixture of about equal value of a-axis and c-axis oriented grains of BaTiO3. The dielectric permittivity, ɛ, of the BaTiO3 layer was almost twice as large, at T>200 K and f=100 kHz, for the LaAlO3 substrate as compared to the MgO one. Its maximum value (ɛ/ɛ0≈6200) depended on temperature of growth, grain size, and electric field and compares well with optimal values commonly used for ceramic material. The maximum in the ɛ(T) shifted from about 370 to 320 K when the grain size in the BaTiO3 film decreased from 100 to 40 nm. At T300 K, hysteresis loops in polarization versus electric field were roughly symmetric. The BaTiO3 films grown on (100)SrRuO3/(100)MgO exhibit the largest remnant polarizations and coercive fields in the temperature range 100-380 K.

Discovery of a phosphor for light emitting diode applications and its structural determination, Ba(Si,Al)5(O,N)8:Eu2+.

Science.gov (United States)

Park, Woon Bae; Singh, Satendra Pal; Sohn, Kee-Sun

2014-02-12

Most of the novel phosphors that appear in the literature are either a variant of well-known materials or a hybrid material consisting of well-known materials. This situation has actually led to intellectual property (IP) complications in industry and several lawsuits have been the result. Therefore, the definition of a novel phosphor for use in light-emitting diodes should be clarified. A recent trend in phosphor-related IP applications has been to focus on the novel crystallographic structure, so that a slight composition variance and/or the hybrid of a well-known material would not qualify from either a scientific or an industrial point of view. In our previous studies, we employed a systematic materials discovery strategy combining heuristics optimization and a high-throughput process to secure the discovery of genuinely novel and brilliant phosphors that would be immediately ready for use in light emitting diodes. Despite such an achievement, this strategy requires further refinement to prove its versatility under any circumstance. To accomplish such demands, we improved our discovery strategy by incorporating an elitism-involved nondominated sorting genetic algorithm (NSGA-II) that would guarantee the discovery of truly novel phosphors in the present investigation. Using the improved discovery strategy, we discovered an Eu(2+)-doped AB5X8 (A = Sr or Ba, B = Si and Al, X = O and N) phosphor in an orthorhombic structure (A21am) with lattice parameters a = 9.48461(3) Å, b = 13.47194(6) Å, c = 5.77323(2) Å, α = β = γ = 90°, which cannot be found in any of the existing inorganic compound databases.

A novel greenish yellow-orange red Ba3Y4O9:Bi(3+),Eu(3+) phosphor with efficient energy transfer for UV-LEDs.

Science.gov (United States)

Li, Kai; Lian, Hongzhou; Shang, Mengmeng; Lin, Jun

2015-12-21

A series of novel color-tunable Ba3Y4O9:Bi(3+),Eu(3+) phosphors were prepared for the first time via the high-temperature solid-state reaction route. The effect of Bi(3+) concentration on the emission intensity of Ba3Y4O9:Bi(3+) was investigated. The emission spectra of the Ba3Y4O9:Bi(3+),Eu(3+) phosphors present both a greenish yellow band of Bi(3+) emission centered at 523 nm, and many characteristic emission lines of Eu(3+), derived from the allowed (3)P1-(1)S0 transition of the Bi(3+) ion and the (5)D0-(7)FJ transition of the Eu(3+) ion, respectively. The energy transfer phenomenon from Bi(3+) to Eu(3+) ions is observed under UV excitation in Bi(3+), Eu(3+) co-doped Ba3Y4O9 phosphors, and their transfer mechanism is demonstrated to be a resonant type via dipole-quadrupole interaction. The critical distance between Bi(3+) and Eu(3+) for the energy transfer effect was calculated via the concentration quenching and spectral overlap methods. Results show that color tuning from greenish yellow to orange red can be realized by adjusting the mole ratio of Bi(3+) and Eu(3+) concentrations based on the principle of energy transfer. Moreover, temperature-dependent PL properties, CIE chromaticity coordinates and quantum yields of Ba3Y4O9:Bi(3+),Eu(3+) phosphors were also supplied. It is illustrated that the as-prepared Ba3Y4O9:Bi(3+),Eu(3+) phosphors can be potential candidates for color-tunable phosphors applied in UV-pumped LEDs.

Thermal properties of perovskite RCeO{sub 3} (R = Ba, Sr)

Energy Technology Data Exchange (ETDEWEB)

Shukla, Aarti, E-mail: aarti.phy@gmail.com [Department of Physics, Barkatullah University, Bhopal 462026 (India); Parey, Vanshree; Thakur, Rasna [Department of Physics, Barkatullah University, Bhopal 462026 (India); Srivastava, Archana [Department of Physics, Sri Sathya Sai College for women, Bhopal 462024 (India); Gaur, N.K. [Department of Physics, Barkatullah University, Bhopal 462026 (India)

2015-08-20

Highlights: • (Ba,Sr)CeO{sub 3} are high temperature protonic conductor materials. • This makes their thermal properties very interesting. • MRIM has successfully predicted the thermodynamic properties. • The computed results are in good agreement with the available experimental data. • Present results will serve as guide to experimental workers in future. - Abstract: We have investigated the bulk modulus and thermal properties of proton conducting perovskite RCeO{sub 3} (R = Ba, Sr) for the first time by incorporating the effect of lattice distortion in modified rigid ion models (MRIM). The computed bulk modulus, specific heat, thermal expansion coefficient and other thermal properties of BaCeO{sub 3} and SrCeO{sub 3} reproduce well with the available experimental data. In addition the cohesive energy (ϕ), molecular force constant (f), reststrahlen frequency (ν), Debye temperature (θ{sub D}) and Gruneisen parameter (γ) are also reported and discussed. The specific heat results can further be improved by taking into account the spin and the orbital ordering contribution in the specific heat formulae.

Multichannel Luminescence Properties of Mixed-Valent Eu2+/Eu3+ Coactivated SrAl3BO7 Nanocrystalline Phosphors for Near-UV LEDs.

Science.gov (United States)

Liu, Xiaoming; Xie, Weijie; Lü, Ying; Feng, Jingchun; Tang, Xinghua; Lin, Jun; Dai, Yuhua; Xie, Yu; Yan, Liushui

2017-11-20

Up to now, orchestrating the coexistence of Eu 2+ and Eu 3+ activators in a single host lattice has been an extremely difficult task, especially for the appearance of the characteristic emission of Eu 2+ and Eu 3+ in order to generate white light. Nevertheless, here we demonstrate a new Eu 2+ /Eu 3+ coactivated SrAl 3 BO 7 nanocrystalline phosphor with abundant and excellent multichannel luminescence properties. A series of Eu 2+ /Eu 3+ coactivated SrAl 3 BO 7 nanocrystalline phosphors were prepared through a Pechini-type sol-gel method followed by a reduction process. With excitation of UV/NUV light, the prepared SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphors show not only the characteristic f-f transitions of Eu 3+ ion ( 5 D J → 7 F J,J' , J, J' = 0-3), but also the 5d → 4f transitions of Eu 2+ ion with comparable intensity from 400 to 700 nm in the whole visible spectral region. The luminescence color of the SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor can be tuned from blue, blue-green, white, and orange to orange-red by changing the excitation wavelength, the overall doping concentration of europium ions (Eu 2+ , Eu 3+ ), and the relative ratio of Eu 2+ to Eu 3+ ions to some extent. A single-phase white-light emission has been realized in SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor. The obtained SrAl 3 BO 7 :Eu 2+ ,Eu 3+ phosphor has potential application in the area of NUV white-light-emitting diodes.

High-pressure modifications of CaZn2, SrZn2, SrAl2, and BaAl2: Implications for Laves phase structural trends

International Nuclear Information System (INIS)

Kal, Subhadeep; Stoyanov, Emil; Belieres, Jean-Philippe; Groy, Thomas L.; Norrestam, Rolf; Haeussermann, Ulrich

2008-01-01

High-pressure forms of intermetallic compounds with the composition CaZn 2 , SrZn 2 , SrAl 2 , and BaAl 2 were synthesized from CeCu 2 -type precursors (CaZn 2 , SrZn 2 , SrAl 2 ) and Ba 21 Al 40 by multi-anvil techniques and investigated by X-ray powder diffraction (SrAl 2 and BaAl 2 ), X-ray single-crystal diffraction (CaZn 2 ), and electron microscopy (SrZn 2 ). Their structures correspond to that of Laves phases. Whereas the dialuminides crystallize in the cubic MgCu 2 (C15) structure, the dizincides adopt the hexagonal MgZn 2 (C14) structure. This trend is in agreement with the structural relationship displayed by sp bonded Laves phase systems at ambient conditions. - Graphical abstract: CeCu 2 -type polar intermetallics can be transformed to Laves phases upon simultaneous application of pressure and temperature. The observed structures are controlled by the valence electron concentration

Red Emission of SrAl2O4:Mn4+ Phosphor for Warm White Light-Emitting Diodes

Science.gov (United States)

Chi, N. T. K.; Tuan, N. T.; Lien, N. T. K.; Nguyen, D. H.

2018-05-01

In this work, SrAl2O4:Mn4+ phosphor is prepared by co-precipitation. The phase structure, morphology, composition and luminescent performance of the phosphor are investigated in detail with x-ray diffraction, field emission scanning electron microscopy, steady-state photoluminescence (PL) spectra, and temperature-dependent PL measurements. The phosphor shows a strong red emission peak at ˜ 690 nm, which is due to the transition between electronic levels and the electric dipole transition 2Eg to 4A2g of Mn4+ ions located at the sites with D3d local symmetry. The sample doped with 0.04 mol.% Mn4+ exhibits intense red emission with high thermal stability and appropriate International Commission on Illumination (CIE) coordinates (x = 0.6959, y = 0.2737). It is also found that the phosphor absorption in an extended band from 250 nm to 500 nm has three peaks at 320 nm, 405 nm, and 470 nm, which match well with the emission band of ultraviolet (UV) lighting emission diode (LED) or blue LED chips. These results demonstrate that SrAl2O4:Mn4+ phosphor can play the role of activator in narrow red-emitting phosphor, which is potentially useful in UV (˜ 320 nm) or blue (˜ 460 nm) LED.

Enhanced orange-red emission by using Mo codoped in Ba2CaWO6: Eu3+, Li+ phosphor under near UV excitation

International Nuclear Information System (INIS)

Sun, Xiaoyuan; Hao, Zhendong; Li, Chunjie; He, Xiaoguang; Qi, Haiyan; Yu, Lijun; Luo, Yongshi; Zhang, Jiahua; Gao, Jiwei; Zhong, Ruixia

2013-01-01

The orange-red emitting phosphors Ba 2 Ca 0.9 Mo x W 1−x O 6 :Eu 3+ 0.05 , Li + 0.05 (x=0, 0.05, 0.1, 0.15, 0.2, 0.25, 0.5, 0.75, and 1.0) and Ba 2 Ca 1−2y Mo 0.2 W 0.8 O 6 :Eu 3+ y , Li + y (y=0.03, 0.05, 0.07, 0.1, and 0.15) were synthesized. The crystalline structure and photoluminescence properties of these phosphors were described. The strong orange-red emission of Eu 3+ ( 5 D 0 — 7 F 1 transition) at around 593 nm was observed. Addition of Mo strongly enhances the charge transfer band absorption in the near ultraviolet region that corresponds to near ultraviolet white light emitting diode. The dependence of photoluminescence intensities on Eu 3+ concentrations with optimal Mo concentration under 400 nm excitation was studied. The phosphor is considered to be a promising orange-red emitting phosphor for near ultraviolet GaN-based white light emitting diode. - Highlights: ► The samples form solid solutions when Mo is added into Ba 2 CaWO 6 : Eu 3+ , Li + phosphors. ► Addition of Mo in Ba 2 CaWO 6 : Eu 3+ , Li + shifts the PLE spectra maximum from UV region to near UV region. ► In Ba 2 CaMo x W 1−x O 6 :Eu 3+ , Li + , the most efficient concentrations occur at 0.1 and 0.2 for Eu and Mo.

Synthesis and photoluminescence properties of LiSrPO{sub 4}:Eu{sup 2+} phosphor for solid state lighting

Energy Technology Data Exchange (ETDEWEB)

Game, D. N., E-mail: deorao.game@gmail.com [Deccan Education Society’s Technical Institute, Fergusson College Campus, Pune (India); Taide, S. T.; Khan, Z. S.; Omanwar, S. K. [Department of Physics, Sant Gadge Baba, Aravati University, Amravati (India); Ingale, N. B. [Prof. Ram Meghe Institute of Technology and Research, Badnera, Amravati (India)

2016-05-06

A novel method to prepare orthophosphate LiSrPO{sub 4}: Eu{sup 2+} phosphor for white light-emitting diodes (w-LEDs) is given in this paper. Phosphor was successfully synthesized by Pechini (citrate gel) method which is efficient than conventional high temperature solid state reaction. X-ray powder diffraction (XRD) analysis confirmed the single phase formation of LiSrPO{sub 4}:Eu{sup 2+} with monoclinic crystal structure. Luminescence results showed that the phosphor could be efficiently excited by near UV and exhibited bright blue emission at λ{sub em} = 420 nm corresponding to 5d– 4f transition of Eu{sup 2+}. The phosphor exhibits blue emission bands under 350 nm excitation. This mercury-free excitation is useful for solid state lighting and light-emitting diode (LED). Hence it could be useful for solid state lighting and light-emitting diode (LED) application.

Photoluminescence properties of a novel red phosphor Sr{sub 3}Ga{sub 2}O{sub 5}Cl{sub 2}:Eu{sup 3+}

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhonghua; Hu, Yihua; Zhang, Shaoan; Lin, Jun [Guangdong University of Technology, School of Physics and Optoelectronic Engineering, Guangzhou (China)

2016-02-15

Eu{sup 3+}-doped Sr{sub 3}Ga{sub 2}O{sub 5}Cl{sub 2} phosphors were synthesized successfully via a two-step solid-state reaction method. Phase purity and morphology of the phosphor were confirmed by XRD and SEM techniques. In the excitation spectra of Sr{sub 3}Ga{sub 2}O{sub 5}Cl{sub 2}:Eu{sup 3+} phosphor, the broad excitation band centering at 310 nm is due to the combination of charge transfer from Eu{sup 3+}→O{sup 2-} and host absorption. And it matches well the emission wavelength from UV LEDs. Sr{sub 3}Ga{sub 2}O{sub 5}Cl{sub 2}:Eu{sup 3+} phosphors show a bright orange-red luminescence under excitation with 301 nm. However, concentration quenching of Eu{sup 3+} in Sr{sub 3}Ga{sub 2}O{sub 5}Cl{sub 2}:Eu{sup 3+} occurs at a low content of 0.07 in this work. The quenching mechanism of Sr{sub 3}Ga{sub 2}O{sub 5}Cl{sub 2}:Eu{sup 3+} was discussed in detail on the basis of the experimental results. (orig.)

Study on luminescence and thermal stability of blue-emitting Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+}phosphor for application in InGaN-based LEDs

Energy Technology Data Exchange (ETDEWEB)

Liu, Jie; Zhang, Zhi-Ming [State Key Laboratory Base of Eco-chemical Engineering, Laboratory of Inorganic Synthesis and Applied Chemistry, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Wu, Zhan-Chao, E-mail: wuzhan_chao@163.com [State Key Laboratory Base of Eco-chemical Engineering, Laboratory of Inorganic Synthesis and Applied Chemistry, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Wang, Fang-Fang [State Key Laboratory Base of Eco-chemical Engineering, Laboratory of Inorganic Synthesis and Applied Chemistry, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Li, Zhen-Jiang, E-mail: zjli126@126.com [State Key Laboratory Base of Eco-chemical Engineering, College of Sino-German Science and Technology, Qingdao University of Science and Technology, 53 Zhengzhou Road, Qingdao 266042, Shandong (China)

2017-07-15

Highlights: • A blue phosphor Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} was prepared at low temperature of 800 °C. • The broad excitation band of the phosphor matches well with NUV LED chips. • The phosphor shows high color purity and good color stability. • A bright blue-emitting LED was fabricated with this phosphor on an InGaN chip. - Abstract: A series of blue-emitting phosphors Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} were synthesized by traditional high temperature solid-state reaction method. The micro-morphology and photoluminescence properties of the phosphors were investigated. The Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors exhibit broad excitation spectra ranging from 250 to 420 nm, and an intense asymmetric blue emission band peaking at 435 nm. Two different Eu{sup 2+} emission centers in Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors were confirmed via their fluorescence properties. The concentration quenching mechanism, fluorescence lifetime and thermal stability of Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors were studied in detail. The thermal stability can be improved obviously by anion substitution. The CIE chromaticity coordinates of Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} phosphors with different Eu{sup 2+}-doped concentrations were calculated. A blue light-emitting diode was fabricated by combination of a 370 nm InGaN chip and the prepared phosphor Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+}. The present work suggests that Sr{sub 5}(PO{sub 4}){sub 3}F: Eu{sup 2+} is a potential phosphor applied in InGaN-based LEDs.

Energy transfer from Pr3+ to Gd3+ ions in BaB8O13 phosphor for phototherapy lamps

Science.gov (United States)

Tamboli, Sumedha; Nair, Govind B.; Dhoble, S. J.; Burghate, D. K.

2018-04-01

A series of BaB8O13 phosphors doped with different concentrations of Gd3+ ions and co-doped with Pr3+ ions were synthesized by solid state synthesis method. X-ray powder diffraction (XRD) analysis confirmed the formation of the compound in a crystalline and homogeneous form. Scanning Electron Microscopy (SEM) was performed to study the surface morphology of the compound and Fourier Transform Infrared (FT-IR) spectroscopy measurements determined the nature of bonding between elements of the compounds. The photoluminescence (PL) excitation spectra of BaB8O13:Gd3+ phosphor showed excitation peaks at 246 nm, 252 nm and 274 nm. The prominent emission peak was observed at 313 nm which is in narrow band ultraviolet B (NB-UVB) range. Energy transfer was achieved by co-doping Pr3+ ions with Gd3+ ions. PL decay time was also measured for BaB8O13: Gd3+, Pr3+ phosphor. Emission at 313 nm can be used for the treatment of skin diseases.

Compounds of the type Ba/sub 3/Bsup(II)M/sub 2/sup(V)O/sub 9/ with Bsup(II) = Mg, Ca, Sr, Ba, and Msup(V) = Nb, Ta

Energy Technology Data Exchange (ETDEWEB)

Kemmler-Sack, S; Thumm, I; Herrmann, M [Tuebingen Univ. (Germany, F.R.). Lehrstuhl fuer Anorganische Chemie 2

1981-08-01

The hexagonal perovskites Ba/sub 3/Bsup(II)M/sub 2/sup(V)O/sub 9/ (Msup(V) = Nb, Ta) crystallize with Bsup(II) = Mg, Ca in a 3 L structure (sequence (c)/sub 3/) and Bsup(II) = Sr in the hexagonal BaTiO/sub 3/ type (6 L; sequence (hcc)/sub 2/) with an 1:2 order for the B and M ions. Intensity calculations for Ba/sub 3/SrNb/sub 2/O/sub 9/ and Ba/sub 3/SrTa/sub 2/O/sub 9/ gave in the space group P6/sub 3//mmc a refined, intensity related R' value of 8.4% (Nb) and 9.0% (Ta) respectively. For Bsup(II) = Ba the perovskite Ba/sub 3/BaTa/sub 2/O/sub 9/ has an orthorhombic distorted 6 L structure and forms with Ba/sub 3/SrTa/sub 2/O/sub 9/ a continuous series of mixed crystals (Ba/sub 3/Srsub(1-x)Basub(x)Ta/sub 2/O/sub 9/). In the system Ba/sub 3/Srsub(1-x)Basub(x)Nb/sub 2/O/sub 9/ the range of existence of the hexagonal BaTiO/sub 3/ type is confined to the Sr richer end. The pure Ba compound posesses a proper structure type (5 L: Ba/sub 5/BaNb/sub 3/vacantOsub(13.5)vacantsub(1.5)).

Comparison of the photoluminescence properties of Eu{sup 2+}, Mn{sup 2+} co-doped M{sub 5}(PO{sub 4}){sub 3}Cl (M = Ca, Sr, Ba)

Energy Technology Data Exchange (ETDEWEB)

Yang, Fengli [National Engineering Research Center for Rare Earth Materials, General Research Institute for Nonferrous Metals, and Grirem Advanced Materials Co., Ltd., Beijing 100088 (China); State Key Laboratory of Rare Earth Materials and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou, Jiangxi 341000 (China); An, Wei [School of Physics, Peking University, Beijing 100871 (China); Wei, Heng-Wei [State Key Laboratory of Rare Earth Materials and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Chen, Guantong [National Engineering Research Center for Rare Earth Materials, General Research Institute for Nonferrous Metals, and Grirem Advanced Materials Co., Ltd., Beijing 100088 (China); Zhuang, Weidong, E-mail: wdzhuang@126.com [National Engineering Research Center for Rare Earth Materials, General Research Institute for Nonferrous Metals, and Grirem Advanced Materials Co., Ltd., Beijing 100088 (China); Jing, Xi-Ping, E-mail: xpjing@pku.edu.cn [State Key Laboratory of Rare Earth Materials and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China)

2014-03-25

Highlights: • Good size match between the doped and host cations narrows the emission band. • Low phonon energy of the hosts enhances the luminescence intensity. • “Inverse bottleneck effect” related to Eu/Mn lifetime mismatch causes quenching. • “Charge transfer process” in the Eu–Mn clusters causes quenching. -- Abstract: Eu{sup 2+} and Mn{sup 2+} singly doped or co-doped M{sub 5}(PO{sub 4}){sub 3}Cl (M = Ca, Sr and Ba) phosphors were synthesized by conventional solid state reactions and characterized by X-ray diffraction (XRD), photoluminescence (PL) spectra, PL decay curves, energy dispersive spectra (EDS) and Raman spectra. The results show that a better size match between the doped cation and the host cation allows a wider solid solution range (e.g. Ca{sup 2+}/Mn{sup 2+}) and a narrower emission band (e.g. Sr{sup 2+}/Eu{sup 2+} and Ca{sup 2+}/Mn{sup 2+}). A lower phonon energy of the host (e.g. the Sr phase) reduces the non-radiation probability and enhances the PL efficiency. The PL performance of the Ba phase is exceptional possibly because of the large size difference between the doped cations and the host cations. The transfer efficiency (η) and the emission quantum efficiency (Q) were analyzed. In the studied phosphors, superficially Eu{sup 2+} efficiently transferred its absorbed energy to Mn{sup 2+} but the Q of the Mn{sup 2+} emission was not as high as expected. Two loss mechanisms are proposed: an “inverse bottleneck effect” and “charge transfer” between Eu{sup 2+} and Mn{sup 2+}.

Luminescence properties and energy transfer investigations of Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Yang, Zaifa; Xu, Denghui, E-mail: xudh@btbu.edu.cn; Sun, Jiayue; Du, Jiangnan; Gao, Xuedong

2016-09-15

Highlights: • A phosphor Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} for UV-based white LEDs was firstly synthesized successfully. • The phase structure and photoluminescence properties of samples were studied in detail. • The energy transfer process from Ce{sup 3+} to Tb{sup 3+} ions was illustrated in detail. • Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor has potential applications as an UV-convertible phosphor for white light emitting diodes. - Abstract: A series of Ce{sup 3+} or Tb{sup 3+} doped and Ce{sup 3+}/Tb{sup 3+} co-doped Sr{sub 3}Lu(PO{sub 4}){sub 3} phosphors were prepared via the conventional high temperature solid-state reaction. The phase structure, photoluminescence and energy transfer properties of samples were studied in detail. The optimal proportion of Ce{sup 3+} single doping is 4 mol% with maximal fluorescence intensity. The Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor shows both a blue emission (428 nm) from Ce{sup 3+} and a yellowish-green emission (545 nm) from Tb{sup 3+} with considerable intensity under ultraviolet (UV) excitation (268 nm). The energy transfer from Ce{sup 3+} to Tb{sup 3+} ions takes place in the Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor on the basis of the analysis of the luminescence spectra. The energy transfer mechanism from Ce{sup 3+} to Tb{sup 3+} ions was proved to be dipole–dipole interaction. The energy transfer behaviors in Sr{sub 3}Lu(PO{sub 4}){sub 3}:Ce{sup 3+}, Tb{sup 3+} phosphor is also investigated by the lifetime measurement. The results show that this phosphor has potential applications for UV white-light LEDs.

Thermochemical properties of oxides in Y-Ba-Cu-O, Sr-Bi-O, Cu-Nb-O, Sr-Cu-O, Ca-Cu-O, Cu-O and Hg-Ba-Ca-Cu-O systems

International Nuclear Information System (INIS)

Moiseev, G.K.; Vatolin, N.A.; Il'inykh, N.I.

2000-01-01

Thermochemical properties (ΔH 0 298 , S 0 298 , H 0 298 -H 0 0 , C p (T), C p at T>T melt ) of complex oxides in Y-Ba-Cu-O, Sr-Bi-O, Cu-Nb-O, Sr-Cu-O, Ca-Cu-O, Cu-O and Hg-Ba-Ca-Cu-O systems obtained with application of calculation methods are presented. Nonexperimental methods of estimation, revision and correction of standard formation enthalpies of inorganic compounds are described [ru

Spectral characteristics and white emission of Dy{sup 3+}/Tm{sup 3+}-BaLaGa{sub 3}O{sub 7} phosphors

Energy Technology Data Exchange (ETDEWEB)

Gao, Shufang, E-mail: shfgao@yangtzeu.edu.cn [School of Physics and Optoelectronic Engineering, Yangtze University, Jingzhou 434023 (China); Xu, Shan [School of Physics and Optoelectronic Engineering, Yangtze University, Jingzhou 434023 (China); Wang, Yeqing [Department of Applied Physics, East China Jiaotong University, Nanchang, Jiangxi 330013 (China); Tu, Chaoyang, E-mail: tcy@fjirsm.ac.cn [Key Laboratory of Optoelectronic Materials Chemistry and Physics of CAS, Fujian Institute of Research on the Structure of Matter, CAS, Fuzhou, Fujian 350002 (China)

2016-10-15

Tm{sup 3+}-, Dy{sup 3+}-BaLaGa{sub 3}O{sub 7} phosphors have been synthesized by solid-phase sintering. X-ray diffraction (XRD) and photoluminescence properties of the phosphors were investigated in detail. The sample Tm{sup 3+} and Dy{sup 3+} ions co-doped BaLaGa{sub 3}O{sub 7} obtain white light emission by integrating a blue emission band located at 455 nm ({sup 1}D{sub 2}→{sup 3}F{sub 4}) and an orange one located at 573 nm ({sup 4}F{sub 9/2}→{sup 6}H{sub 13/2}) attributed to Tm{sup 3+} and Dy{sup 3+} ions, respectively. The study on the luminescence mechanism showed that there is the energy transfer between Tm{sup 3+} and Dy{sup 3+} in Tm{sup 3+}/Dy{sup 3+}-BaLaGa{sub 3}O{sub 7} phosphors.

Electrical properties of resistive switches based on Ba1-χSrχTiO3 thin films prepared by RF co-sputtering

International Nuclear Information System (INIS)

Marquez H, A.; Hernandez R, E.; Zapata T, M.; Guillen R, J.; Cruz, M. P.; Calzadilla A, O.; Melendez L, M.

2010-01-01

In this work, was proposed the use of Ba 1-χ Sr χ TiO 3 (0≤x≤1) thin films for the construction of metal-insulator-metal heterostructures; and their great potential for the development of non-volatile resistance memories (ReRAM) is shown. The deposition of Ba 1-χ Sr χ TiO 3 thin films was done by the RF co-sputtering technique using two magnetron sputtering cathodes with BaTiO 3 and SrTiO 3 targets. The chemical composition (x parameter) in the deposited Ba 1-χ Sr χ TiO 3 thin films was varied through the RF powder applied to the targets. The constructed metal-insulator-metal heterostructures were Al/Ba 1-χ Sr χ TiO 3 /nichrome. The I-V measurements of the heterostructures showed that their hysteretic characteristics change depending on the Ba/Sr ratio of the Ba 1-χ Sr χ TiO 3 thin films; the Ba/Sr ratio was determined by employing the energy dispersive spectroscopy; Sem micrographs showed that Ba 1-χ Sr χ TiO 3 thin films were uniform without cracks or pinholes. Additionally, the analysis of the X-ray diffraction results indicated the substitutional incorporation of Sr into the BaTiO 3 lattice and the obtainment of crystalline films for the entire range of the x values. (Author)

Photoluminescence Properties of Red-Emitting Ca3Sr3-x(PO4)4:xEu3+ Phosphors for White Light-Emitting Diodes.

Science.gov (United States)

Hakeem, D A; Park, K

2015-07-01

The photoluminescent properties of the Eu(3+)-activated Ca3Sr3(PO4)4 phosphors prepared by a solution combustion method were investigated. The excitation spectra of Ca3Sr3-x(PO4)4:xEu3+ (0.05 ≤ x ≤ 0.6) phosphors under 614 nm wavelength showed a broad band centered at 266 nm along with other peaks at 320, 362, 381, 394, 414, 464, and 534 nm. The emission spectra observed in the range of 450 to 750 nm under excitation at 394 nm were ascribed to the 5D0-7F1-4 transitions of Eu3+ ions. The Ca3Sr3-x(PO4)4:xEu3+ phosphors showed the strongest red emission at 614 nm due to the electric dipole 5DO -->7F2 transition of Eu3+. The strongest emission intensity was obtained for the Eu3+ ions of x = 0.5. The prepared Ca3Sr3-x(PO4)4:xEu3+ can be used as an efficient red phosphor for UV-based white LEDs.

A novel yellow-emitting SrAlSi4N7:Ce3+ phosphor for solid state lighting: Synthesis, electronic structure and photoluminescence properties

International Nuclear Information System (INIS)

Ruan, Jian; Xie, Rong-Jun; Funahashi, Shiro; Tanaka, Yoshinori; Takeda, Takashi; Suehiro, Takayuki; Hirosaki, Naoto; Li, Yuan-Qiang

2013-01-01

Ce 3+ -doped and Ce 3+ /Li + -codoped SrAlSi 4 N 7 phosphors were synthesized by gas pressure sintering of powder mixtures of Sr 3 N 2 , AlN, α-Si 3 N 4 , CeN and Li 3 N. The phase purity, electronic crystal structure, photoluminescence properties of SrAlSi 4 N 7 :Ce 3+ (Ce 3+ /Li + ) were investigated in this work. The band structure calculated by the DMol 3 code shows that SrAlSi 4 N 7 has a direct band gap of 3.87 eV. The single crystal analysis of Ce 3+ -doped SrAlSi 4 N 7 indicates a disordered Si/Al distribution and nitrogen vacnacy defects. SrAlSi 4 N 7 was identified as a major phase of the fired powders, and Sr 5 Al 5 Si 21 N 35 O 2 and AlN as minor phases. Both Ce 3+ and Ce 3+ /Li + doped SrAlSi 4 N 7 phosphors can be efficiently excited by near-UV or blue light and show a broadband yellow emission peaking around 565 nm. A highest external quantum efficiency of 38.3% under the 450 nm excitation was observed for the Ce 3+ /Li + -doped SrAlSi 4 N 7 (5 mol%). A white light LED lamp with color temperature of 6300 K and color rendering index of Ra=78 was achieved by combining Sr 0.97 Al 1.03 Si 3.997 N/94/maccounttest14=t0005 1 8193 7 :Ce 3+ 0.03 with a commercial blue InGaN chip. It indicates that SrAlSi 4 N 7 :Ce 3+ is a promising yellow emitting down-conversion phosphor for white LEDs. - Graphical abstract: One-phosphor converted white light-emitting diode (LED) was fabricated by combining a blue LED chip and a yellow-emitting SrAlSi4N7:Ce 3+ phosphor (see inset), which has the color rendering index of 78 and color temperature of 6300 K. - Highlights: • We reported a new yellow nitride phosphor suitable for solid state lighting. • We solved the crystal structure and evidenced a disordered Si/Al distribution. • We fabricated a high color rendering white LEDs by using a single SrAlSi4N7:Ce

Crystallization and properties of Sr-Ba aluminosilicate glass-ceramic matrices

Science.gov (United States)

Bansal, Narottam P.; Hyatt, Mark J.; Drummond, Charles H., III

1991-01-01

Powders of roller quenched (Sr,Ba)O-Al2O3-2SiO2 glasses of various compositions were uniaxially pressed into bars and hot isostatically pressed at 1350 C for 4 hours or cold isostatically pressed and sintered at different temperatures between 800 to 1500 C for 10 or 20 hours. Densities, flexural strengths, and linear thermal expansion were measured for three compositions. The glass transition and crystallization temperatures were determined by Differential Scanning Calorimetry (DSC). The liquidus and crystallization temperature from the melt were measured using high temperature Differential Thermal Analysis (DTA). Crystalline phases formed on heat treatment of the glasses were identified by powder X ray diffraction. In Sr containing glasses, the monoclinic celsian phase always crystallized at temperatures above 1000 C. At lower temperatures, the hexagonal analog formed. The temperature for orthorhombic to hexagonal structural transformation increased monotonically with SrO content, from 327 C for BaO-Al2O3-2SiO2 to 758 C for SrO-Al2O3-2SiO2. These glass powders can be sintered to almost full densities and monoclinic celsian phase at a relatively low temperature of 1100 C.

Color-tunable and highly thermal stable Sr{sub 2}MgAl{sub 22}O{sub 36}:Tb{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Zhang, Haiming; Zhang, Haoran; Liu, Yingliang [Guangdong Provincial Engineering Technology Research Center for Optical Agricultural, College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China); Lei, Bingfu, E-mail: tleibf@scau.edu.cn [Guangdong Provincial Engineering Technology Research Center for Optical Agricultural, College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China); Deng, Jiankun [Guangdong Provincial Engineering Technology Research Center for Optical Agricultural, College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China); Liu, Wei-Ren [Department of Chemical Engineering, Chung Yuan Christian University, Taoyuan City, Taiwan (China); Zeng, Yuan; Zheng, Lingling; Zhao, Minyi [Guangdong Provincial Engineering Technology Research Center for Optical Agricultural, College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China)

2017-06-01

Tb{sup 3+} activated Sr{sub 2}MgAl{sub 22}O{sub 36} phosphor was prepared by a high-temperature solid-state reaction route. The X-ray diffraction, scanning electron microscopy, and photoluminescence spectroscopy were used to characterize the as-prepared samples. The Sr{sub 2}MgAl{sub 22}O{sub 36}:Tb{sup 3+} phosphors show intense green light emission under UV excitation. The phosphor exhibit two groups of emission lines from about 370 to 700 nm, which originating from the characteristic {sup 5}D{sub 3}-{sup 7}F{sub J} and {sup 5}D{sub 4}-{sup 7}F{sub J} transitions of the Tb{sup 3+} ion, respectively. The cross-relaxation mechanism between the {sup 5}D{sub 3} and {sup 5}D{sub 4} emission was investigated and discussed. The emission colors of these phosphors can be tuned from bluish-green to green by adjusting the Tb{sup 3+} doping concentration. Furthermore, the thermal quenching temperature (T{sub 1/2}) is higher than 500 K. The excellent thermal stability and color-tunable luminescent properties suggest that the developed material is a promising green-emitting phosphor candidate for optical devices. - Highlights: • A Color-tunable emitting phosphor Sr{sub 2}MgAl{sub 22}O{sub 36}:Tb{sup 3+} was prepared successfully via high-temperature solid-state reaction. • The photoluminescence of Sr{sub 2}MgAl{sub 22}O{sub 36}:Tb{sup 3+} shows highly thermal stable. • The cross-relaxation mechanism between the {sup 5}D{sub 3} and {sup 5}D{sub 4} emission was investigated and discussed.

Ferromagnetic Instability in AFe4Sb12 (A = Ca, Sr, and Ba)

OpenAIRE

Matsuoka, E.; Hayashi, K.; Ikeda, A.; Tanaka, K.; Takabatake, T.; Higemoto, W.; Matsumura, M.

2004-01-01

Magnetic, transport and thermal properties of AFe4Sb12 (A = Ca, Sr, Ba) are reported. All three compounds show a maximum in both the magnetic susceptibility and thermopower at 50 K, and a large electronic specific heat coefficient of 100 mJ/mol K2. These properties are the characteristics of a nearly ferromagnetic metal. Furthermore, a remanent moment of the order of 10-3muB/Fe was observed below 54, 48, and 40 K for A = Ca, Sr, and Ba, respectively. The volume fraction of the ferromagnetic c...

Novel bluish white-emitting CdBaP{sub 2}O{sub 7}:Eu{sup 2+} phosphor for near-UV white-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Derbel, Mouna [Laboratory of Industrial Chemistry, National School of Engineers of Sfax, University of Sfax, BPW 3038 Sfax (Tunisia); Mbarek, Aïcha, E-mail: mbarekaicha@yahoo.fr [Laboratory of Industrial Chemistry, National School of Engineers of Sfax, University of Sfax, BPW 3038 Sfax (Tunisia); Chadeyron, Geneviève [Clermont Université, ENSCCF, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); Clermont Université, Université Blaise Pascal, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); Fourati, Mohieddine [Laboratory of Industrial Chemistry, National School of Engineers of Sfax, University of Sfax, BPW 3038 Sfax (Tunisia); Zambon, Daniel [Clermont Université, Université Blaise Pascal, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); Mahiou, Rachid [Clermont Université, Université Blaise Pascal, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); CNRS, UMR 6296, ICCF, BP 80026, F-63171 Aubiere (France)

2016-08-15

A new bluish white-emitting phosphor based on a phosphate host matrix, CdBaP{sub 2}O{sub 7}:Eu{sup 2+}, was prepared by a conventional solid-state reaction method. The photoluminescence properties were investigated in both ultraviolet (UV) and vacuum ultraviolet (VUV) regions. The band-gaps of Eu-doped CdBaP{sub 2}O{sub 7} powders can be tuned in the ranges of 2.26–2 eV. The Eu{sup 2+}-doped CdBaP{sub 2}O{sub 7} phosphor was efficiently excited at wavelengths of 250–400 nm, which is suitable for the blue emission band for near-UV light-emitting-diode (LED) chips (360–400 nm) and red emission peaks up to 700 nm. CdBaP{sub 2}O{sub 7}:Eu{sup 2+} displays two different luminescence centers, which were suggested to Ba{sup 2+} and Cd{sup 2+} sites in the host. The dependence of luminescence intensity on temperatures was measured. The chromaticity coordinates and activation energy for thermal quenching were reported. The phosphor shows a good thermal stability on temperature quenching.

Synthesis and photoluminescence properties of Pb{sup 2+} doped inorganic borate phosphor NaSr{sub 4}(BO{sub 3}){sub 3}

Energy Technology Data Exchange (ETDEWEB)

Chauhan, A. O., E-mail: abhi2718@gmail.com; Koparkar, K. A.; Omanwar, S. K. [Department of Physics, SantGadge Baba Amravati University, Amravati MH, 444602 (India); Bajaj, N. S. [Department of Physics, Toshniwal Art, Commerce and Science College, Sengoan, Hingoli MH (India)

2016-05-06

A series of Inorganic borate phosphors NaSr{sub 4}(BO{sub 3}){sub 3} doped with Pb{sup 2+} was successfully synthesized by modified solid state diffusion method. The crystal structure and the phase purity of sample were characterized by powder X-ray diffraction (XRD). The photoluminescence properties of synthesized materials were investigated using spectrofluorometer at room temperature. The phosphor show strong broad band emission spectra in UVA region maximum at 370 nm under the excitation of 289 nm. The dependence of the emission intensity on the Pb{sup 2+} concentration for the NaSr{sub 4}(BO{sub 3}){sub 3} were studied in details. The concentration quenching of Pb{sup 2+} doped NaSr{sub 4}(BO{sub 3}){sub 3} was observed at 0.02 mol. The Stokes shifts of NaSr{sub 4}(BO{sub 3}){sub 3}: Pb{sup 2+} phosphor was calculated to be 7574 cm{sup −1}.

AEMnSb2 (AE=Sr, Ba): a new class of Dirac materials

International Nuclear Information System (INIS)

Farhan, M Arshad; Lee, Geunsik; Shim, Ji Hoon

2014-01-01

The Dirac fermions of Sb square net in AEMnSb 2 (AE=Sr, Ba) are investigated by using first-principles calculation. BaMnSb 2 contains Sb square net layers with a coincident stacking of Ba atoms, exhibiting Dirac fermion behavior. On the other hand, SrMnSb 2 has a staggered stacking of Sr atoms with distorted zig-zag chains of Sb atoms. Application of hydrostatic pressure on the latter induces a structural change from a staggered to a coincident arrangement of AE ions accompanying a transition from insulator to a metal containing Dirac fermions. The structural investigations show that the stacking type of cation and orthorhombic distortion of Sb layers are the main factors to decide the crystal symmetry of the material. We propose that the Dirac fermions can be obtained by controlling the size of cation and the volume of AEMnSb 2 compounds. (fast track communication)

New thermally stable red-emitting phosphors Pr{sup 3+}, M{sup +}:SrB{sub 4}O{sub 7} (M=Li, Na, K)

Energy Technology Data Exchange (ETDEWEB)

Xiong, F.B., E-mail: fbxiong@xmut.edu.cn [Department of Optoelectronics, Xiamen University of Technology, Xiamen 361024 (China); Fujian Provincial Key Laboratory of Optoelectronic Information Materials and Devices, Xiamen University of Technology, Xiamen 361024 (China); Lin, H.F.; Xu, Y.C.; Shen, H.X. [Department of Optoelectronics, Xiamen University of Technology, Xiamen 361024 (China); Zhu, W.Z. [Department of Optoelectronics, Xiamen University of Technology, Xiamen 361024 (China); Fujian Provincial Key Laboratory of Optoelectronic Information Materials and Devices, Xiamen University of Technology, Xiamen 361024 (China)

2016-09-15

New red-emitting phosphors Pr{sup 3+}, M{sup +}:SrB{sub 4}O{sub 7} (M=Li, Na, K) in pure phase were synthesized via high-temperature solid-state reaction. Luminescent properties of those phosphors were characterized in detail. Pr{sup 3+}, M{sup +}:SrB{sub 4}O{sub 7} (M=Li, Na, K) can be excited under the range of 430–500 nm excitation, which covers the emission spectra of blue InGaN chip, exhibits pure red emission bands centered at 605 and 662 nm. The alkali-metal Li{sup +}, Na{sup +}, or K{sup +} acting as charge compensators can improve fluorescent emission intensities of Pr{sup 3+} ions, and Pr{sup 3+}, Na{sup +}:SrB{sub 4}O{sub 7} shows the strongest emission intensities among those phosphors. Concentration quenching could be attributed to electric dipole–dipole interaction among Pr{sup 3+} ions. The temperature-dependent luminescence indicated Pr{sup 3+}, Na{sup +}:SrB{sub 4}O{sub 7} shows highly thermal stability. Those work suggests that Pr{sup 3+}, M{sup +}:SrB{sub 4}O{sub 7} (M=Li, Na, K) as thermally stable red-emitting phosphor might be potentially applied in WLED.

Tuning the electrocaloric effect by varying Sr concentration in ferroelectric Ba1 -xSrxTiO3

Science.gov (United States)

Lisenkov, S.; Ponomareva, I.

2018-05-01

The electrocaloric effect is investigated systematically in Ba1 -xSrxTiO3 ferroelectrics using a semiclassical direct computational approach. The data are reported for the technologically important range of Sr concentrations of 0.0-0.6, electric fields up to 1000 kV/cm, and temperatures ranging from 5 to 600 K. A detailed comparison of computational data with experimental data from the literature reveals semiquantitative agreement and suggests the origin of discrepancies. The electrocaloric change in temperature Δ T shows strong dependence on Sr concentration which offers a way to tune electrocaloric response. In particular, the maximum electrocaloric Δ T is found to decrease with the increase in Sr concentration, whereas the location of the maximum shifts towards lower temperatures following the Curie point of the ferroelectric. Surprisingly, the width of the peak in the dependence of Δ T on the initial temperature is independent of the Sr concentration but shows a strong dependence on the applied electric field. Computational data are used to propose a compositionally graded ferroelectric Ba0.70Sr0.30TiO3/Ba0.55Sr0.45TiO3/Ba0.50Sr0.50TiO3/Ba0.45Sr0.55TiO3 whose Δ T shows almost no temperature dependence in the technologically important range of temperatures and electric fields. Such a desirable feature could potentially lead to the enhancement of relative cooling power.

Is otolith microchemistry (Sr: Ca and Ba:Ca ratios useful to identify Mugil curema populations in the southeastern Caribbean Sea?

Directory of Open Access Journals (Sweden)

E. Avigliano

Full Text Available Abstract The aim of the present study was to evaluate the potential use of otolith microchemistry (Sr:Ca and Ba:Ca ratios to identify silver mullet, Mugil curema, populations in Southeastern Caribbean Sea. Fish samples were collected in 7 areas of Nueva Esparta State (Venezuela. The otolith Sr:Ca and Ba:Ca ratios and water Sr:Ca were determined (by ICP-OES and EDTA volumetric method. Otoliths Sr:Ca and Ba:Ca ratios and Sr:Ca partition coefficient of mullets in Cubagua island (south of the State were significantly different from ratios in La Guardia (north of the State. A discriminant analysis of otolith Sr:Ca and Ba:Ca ratios separated Cubagua Island from La Guardia values. These results suggest the existence of different mullet groups in the Southeastern Caribbean Sea. For this, the simultaneous use of Sr:Ca and Ba:Ca ratios could be a potential tool to identify populations in the study area.

Is otolith microchemistry (Sr: Ca and Ba:Ca ratios) useful to identify Mugil curema populations in the southeastern Caribbean Sea?

Science.gov (United States)

Avigliano, E; Callicó-Fortunato, R; Buitrago, J; Volpedo, A V

2015-11-01

The aim of the present study was to evaluate the potential use of otolith microchemistry (Sr:Ca and Ba:Ca ratios) to identify silver mullet, Mugil curema, populations in Southeastern Caribbean Sea. Fish samples were collected in 7 areas of Nueva Esparta State (Venezuela). The otolith Sr:Ca and Ba:Ca ratios and water Sr:Ca were determined (by ICP-OES and EDTA volumetric method). Otoliths Sr:Ca and Ba:Ca ratios and Sr:Ca partition coefficient of mullets in Cubagua island (south of the State) were significantly different from ratios in La Guardia (north of the State). A discriminant analysis of otolith Sr:Ca and Ba:Ca ratios separated Cubagua Island from La Guardia values. These results suggest the existence of different mullet groups in the Southeastern Caribbean Sea. For this, the simultaneous use of Sr:Ca and Ba:Ca ratios could be a potential tool to identify populations in the study area.

A novel UV-emitting phosphor: NaSr{sub 4}(BO{sub 3}){sub 3}: Pb{sup 2+}

Energy Technology Data Exchange (ETDEWEB)

Pekgözlü, İlhan, E-mail: pekgozluilhan@yahoo.com

2016-01-15

Pb{sup 2+} doped NaSr{sub 4}(BO{sub 3}){sub 3} materials were prepared by a solution combustion synthesis method. The phase analysis of all synthesized materials was carried out using the powder XRD. The synthesized materials were investigated using spectrofluorometer at room temperature. The excitation and emission bands of NaSr{sub 4}(BO{sub 3}){sub 3}: Pb{sup 2+} were observed at 291 and 368 nm, respectively. The dependence of the emission intensity on the Pb{sup 2+} concentration for the NaSr{sub 4}(BO{sub 3}){sub 3} was studied in detail. It was observed that the concentration quenching of Pb{sup 2+} in NaSr{sub 4}(BO{sub 3}){sub 3} is 0.01 mol. The Stokes shifts of NaSr{sub 4}(BO{sub 3}){sub 3}: Pb{sup 2+} phosphor were calculated to be 7190 cm{sup −1}. - Highlights: • A novel UV-emitting phosphor, NaSr{sub 4}(BO{sub 3}){sub 3}: Pb{sup 2+}, was prepared by combustion method. • The excitation and emission bands of NaSr{sub 4}(BO{sub 3}){sub 3}: Pb{sup 2+} were observed at 291 and 368 nm, respectively. • It was observed that the concentration quenching of Pb{sup 2+} in NaSr{sub 4}(BO{sub 3}){sub 3} is 0.01 mol.

Thermoluminescence properties of Eu-doped and Eu/Dy-codoped Sr2 Al2 SiO7 phosphors.

Science.gov (United States)

Jadhaw, Akhilesh; Sonwane, Vivek D; Gour, Anubha S; Jha, Piyush

2017-11-01

We report the thermoluminescence properties of Sr 1.96 Al 2 SiO 7 :Eu 0.04 and Sr 1.92 Al 2 SiO 7 :Eu 0.04 Dy 0.04 phosphors. These phosphors were prepared by a high-temperature solid-state reaction method. The prepared phosphors were characterized by X-ray diffraction. A 254 nm source was used for ultraviolet (UV) irradiation and a 60 Co source was used for γ-irradiation. The effect of heating rate and UV-exposure were examined. The thermoluminescence temperature shifts to higher values with increasing heating rate and thermoluminescence intensity increases with increasing UV exposure time. The trapping parameters such as activation energy (E), order of kinetics and frequency factor (s) were calculated by peak shape method. The effect of γ- and UV-irradiation on thermoluminescence studies was also examined. Copyright © 2017 John Wiley & Sons, Ltd.

Red/blue-shift dual-directional regulation of α-(Ca, Sr)2SiO4:Eu(2+) phosphors resulting from the incorporation content of Eu(2+)/Sr(2+) ions.

Science.gov (United States)

Lu, Zhijuan; Mao, Zhiyong; Chen, Jingjing; Wang, Dajian

2015-09-21

In this work, tunable emission from green to red and the inverse tuning from red to green in α-(Ca, Sr)2SiO4:Eu(2+) phosphors were demonstrated magically by varying the incorporation content of Eu(2+) and Sr(2+) ions, respectively. The tunable emission properties and the tuning mechanism of red-shift resulting from the Eu(2+) content as well as that of blue-shift induced by the Sr(2+) content were investigated in detail. As a result of fine-controlling the incorporation content of Eu(2+), the emission peak red-shifts from 541 nm to 640 nm. On the other hand, the emission peak inversely blue-shifts from 640 nm to 546 nm through fine-adjusting the incorporation content of Sr(2+). The excellent tuning characteristics for α-(Ca, Sr)2SiO4:Eu(2+) phosphors presented in this work exhibited their various application prospects in solid-state lighting combining with a blue chip or a near-UV chip.

Luminescence of a new class of UV-blue-emitting phosphors MSi2O2-deltaN2+2/3delta:Ce3+ (M = Ca, Sr, Ba)

NARCIS (Netherlands)

Li, Y.Q.; With, de G.; Hintzen, H.T.J.M.

2005-01-01

The luminescence properties of Ce3+,Na+-codoped MSi2O22dN2+2/3d (M 5 Ca, Sr, Ba) are reported. The undoped and Ce3+,Na+-codoped MSi2O22dN2+2/3d powders were prepared by a solid-state reaction at temperatures between 1300–1400 uC under N2–H2 (10%) atmosphere in the system MO–SiO2–Si3N4 (M 5 Ca, Sr,

Synthesis and TL/OSL properties of a novel high-sensitive blue-emitting LiSrPO{sub 4}:Eu{sup 2+} phosphor for radiation dosimetry

Energy Technology Data Exchange (ETDEWEB)

Palan, C.B.; Koparkar, K.A.; Omanwar, S.K. [Sant Gadge Baba Amravati University, Department of Physics, Amravati (India); Bajaj, N.S. [Toshniwal Arts, Commerce and Science College, Sengoan, Hingoli District, MH (India); Soni, A. [Bhabha Atomic Research Centre, Radiological Physics and Advisory Division, Mumbai (India)

2016-07-15

In this study, a series of Eu{sup 2+}-doped LiSrPO{sub 4} phosphors were synthesized via solid-state method. The structural and morphological characterizations were done through X-ray diffraction and scanning electronic microscope. Additionally, the photoluminescence (PL), thermoluminescence (TL) and optically stimulated luminescence (OSL) behaviours of LiSrPO{sub 4}:Eu{sup 2+} phosphors were studied. The LiSrPO{sub 4}:Eu{sup 2+} phosphor shows OSL sensitivity about 8 times than that of α-Al{sub 2}O{sub 3}:C phosphor and 6 times than that of LiMgPO{sub 4}:Tb{sup 3+}, B phosphor. Moreover, TL sensitivity was about 15 times more as compared to α-Al{sub 2}O{sub 3}:C phosphor. The kinetic parameters of TL curve were calculated using peak shape method. In TL/OSL mode, dose-response was almost linear nature, in the range of measurement. The minimum detectable dose was found to be 25.18 μGy with 3σ of background. Also, reusability was also studies, which shows the phosphor can be reusable for 10 cycles with 0.1 % change in OSL output. (orig.)

Ba2ZnWO6:Sm3+ as promising orange-red emitting phosphors: Photoluminescence properties and energy transfer process

Science.gov (United States)

Chen, Peng; Hu, Wenyuan; Yang, Dingming; Zhu, Jiayi; Zhang, Jing; Wu, Yadong

2018-02-01

Novel orange-red emitting phosphors, Ba2Zn1-xWO6:xSm3+ (x = 0.03, 0.04, 0.05, 0.06 and 0.07) (BZW:Sm3+), were prepared using a high-temperature solid-state reaction method. Their crystal structure and photoluminescence properties were characterized and the mechanism of energy transfers between Ba2ZnWO6 and Sm3+ elucidated in detail. It was found that the phosphors had a cubic structure with space group Fm 3 bar m . They can be excited by near-ultraviolet light, and the characteristic emissions of Sm3+ ions are observed at 564 nm, 598 nm and 645 nm, corresponding to 4G5/2 → 6H5/2, 4G5/2 → 6H7/2 and 4G5/2 → 6H9/2 transitions, respectively. The 4G5/2 → 6H9/2 transitions shows the greatest intensity, which indicates that Sm3+ ions occupy the noncentrosymmetric sites. The optimal doping concentration of Sm3+ ions in Ba2ZnWO6 is about 5 mol% and the phenomenon of concentration quenching occurs when the content of Sm3+ ions exceeds 5 mol%. All results show that the Ba2ZnWO6:Sm3+ phosphor holds great promise for use in high-quality white light-emitting diodes.

Red-emitting SrIn2O4 : Eu3+ phosphor powders for applications in solid state white lamps

International Nuclear Information System (INIS)

Rodriguez-Garcia, C E; Perea-Lopez, N; Hirata, G A; Baars, S P den

2008-01-01

Red-emitting phosphor powders of SrIn 2 O 4 activated with Eu 3+ ions were fabricated by high pressure assisted combustion synthesis. X-ray diffraction analysis of these oxide phosphors revealed the formation of single-phase orthorhombic SrIn 2 O 4 for concentrations up to 4 at% Eu. A detailed photoluminescence (PL) and cathodoluminescence study showed bright red emission originated within the 5 D 0 → 7 F J intra-shell transitions of Eu 3+ . Furthermore, PL excitation spectroscopy revealed that an efficient energy transfer from the SrIn 2 O 4 host lattice onto the Eu ions is accomplished in addition to the excitation band peaked at 396 nm that directly excites the Eu ions, making this material an excellent candidate for applications in solid state white lamps. (fast track communication)

Magnetothermopower in A2−xLaxFeMoO6 (A = Sr, Ba

Directory of Open Access Journals (Sweden)

G. V. M. Williams

2017-01-01

Full Text Available A magnetothermopower has been observed in electronically spin-polarized polycrystalline Sr2-xLaxFeMoO6 and Ba2FeMoO6. The magnetothermopower is linear up to ~50 K for Sr2-xLaxFeMoO6 and linear up to ~270 K for Ba2FeMoO6. We suggest that the magnetothermopower may arise from a spin-tunneling magnetothermopower between the grains.

First-principles study of the (001) surface of cubic Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Wang, Yuan Xu [Computational Materials Science Center, National Institute for Materials Science, Tsukuba 305-0044 (Japan); Institute for Computational Materials Science, School of Physics and Electronics, Henan University, Kaifeng 475004 (China)

2008-06-15

We have theoretically investigated basic properties of the (001) surface of cubic Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} (BST) by the plane-wave pseudopotential method within the local-density approximation. For the BaSrO{sub 2}-terminated surface, the surface-layer Sr atoms move inward and the surface-layer Ba atoms move outward. Moreover, the displacement of the surface-layer Sr atoms is much larger than the surface-layer Ba atoms. The rumpling of the BaSrO{sub 2}-terminated surface is much larger than that of the Ti{sub 2}O{sub 4}-terminated one. The surface state appears in the band structure of the Ti{sub 2}O{sub 4}-terminated surface of BST. Based on the results of the calculated grand thermodynamic potential, only the BaSrO{sub 2}-terminated surface can exist in the (001) surface of cubic BST. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Synthesis and Luminescence Properties of Blue Na(Sr0.97-xCa(x))PO4:0.03Eu2+ Phosphors for White Light Emitting Diode Applications.

Science.gov (United States)

Hakeem, D A; Park, K

2015-07-01

The crystal structure and luminescence properties of Na(Sr0.97-xCax)PO4:0.03Eu2+ (0 phosphors were studied, depending on the Ca2+ concentration. All the Na(Sr0.97-xCax)PO4:0.03Eu2+ phosphors had a hexagonal crystal structure. The excitation spectra of the prepared phosphors showed a broad band ranging from 250 to 420 nm, which arises due to the 4f-5d transitions of Eu2+ ions. Upon the excitation of 334 nm wavelength, the emission spectra showed a broad blue band ranging from 400 to 700 nm peaking at 450 nm. Among the prepared phosphors, the Na(Sr0.72Ca0.25)PO4:0.03Eu2+ showed the strongest emission intensity and could be applied as a blue emitting phosphor for UV-based w-LEDs.

Eu2+-doped Ba2GaB4O9Cl blue-emitting phosphor with high color purity for near-UV-pumped white light-emitting diodes

Science.gov (United States)

Gao, Zhiwen; Deng, Huajuan; Xue, Na; Jeong, Jung Hyun; Yu, Ruijin

2018-01-01

Eu2+-doped borate fluoride Ba2GaB4O9Cl was synthesized by the conventional high-temperature solid-state reaction. The crystal structure and luminescence properties of the phosphors, as well as their thermal luminescence quenching capabilities and CIE chromaticity coordinates were systematically investigated. Under the excitation at 340 nm, the phosphor exhibited an asymmetric broad-band blue emission with a peak at 445 nm, which is ascribed to the 4f-5d transition of Eu2+. It was further proved that energy transfer among the nearest neighbor ions is the major mechanism for concentration quenching of Eu2+ in Ba2-xGaB4O9Cl:xEu2+ phosphors. The luminescence quenching temperature is 432 K. The CIE color coordinates are very close to those of BaMgAl10O17:Eu2+ (BAM). All the properties indicated that the blue-emitting Ba2GaB4O9Cl:Eu2+ phosphor has potential application in white LEDs.

Monolithic translucent BaMgAl10O17:Eu2+ phosphors for laser-driven solid state lighting

Directory of Open Access Journals (Sweden)

Clayton Cozzan

2016-10-01

Full Text Available With high power light emitting diodes and laser diodes being explored for white light generation and visible light communication, thermally robust encapsulation schemes for color-converting inorganic phosphors are essential. In the current work, the canonical blue-emitting phosphor, high purity Eu-doped BaMgAl10O17, has been prepared using microwave-assisted heating (25 min and densified into translucent ceramic phosphor monoliths using spark plasma sintering (30 min. The resulting translucent ceramic monoliths convert UV laser light to blue light with the same efficiency as the starting powder and provide superior thermal management in comparison with silicone encapsulation.

Ca, Sr and Ba stable isotopes reveal the fate of soil nutrients along a tropical climosequence

Science.gov (United States)

Bullen, Thomas D.; Chadwick, Oliver A.

2016-01-01

Nutrient biolifting is an important pedogenic process in which plant roots obtain inorganic nutrients such as phosphorus (P) and calcium (Ca) from minerals at depth and concentrate those nutrients at the surface. Here we use soil chemistry and stable isotopes of the alkaline earth elements Ca, strontium (Sr) and barium (Ba) to test the hypothesis that biolifting of P has been an important pedogenic process across a soil climosequence developed on volcanic deposits at Kohala Mountain, Hawaii. The geochemical linkage between these elements is revealed as generally positive site-specific relationships in soil mass gains and losses, particularly for P, Ba and Ca, using the ratio of immobile elements titanium and niobium (Ti/Nb) to link individual soil samples to a restricted compositional range of the chemically and isotopically diverse volcanic parent materials. At sites where P is enriched in surface soils relative to abundances in deeper soils, the isotope compositions of exchangeable Ca, Sr and Ba in the shallowest soil horizons ( 10 cm depth) at those sites is consistently heavier than the volcanic parent materials. The isotope compositions of exchangeable Ca and Sr trend toward heavier compositions with depth more gradually, reflecting increasing leakiness from these soils in the order Ba < Sr < Ca and downward transfer of light biocycled Ca and Sr to deeper exchange sites. Given the long-term stability of ecosystem properties at the sites where P is enriched in surface soils, a simple box model demonstrates that persistence of isotopically light exchangeable Ca, Sr and Ba in the shallowest soil horizons requires that the uptake flux to plants from those near-surface layers is less than the recycling flux returned to the surface as litterfall. This observation implicates an uptake flux from an additional source which we attribute to biolifting. We view the heavy exchangeable Ba relative to soil parent values in deeper soils at sites where P is enriched in

A single-phase white light emitting Pr3+ doped Ba2CaWO6 phosphor: synthesis, photoluminescence and optical properties

Science.gov (United States)

Sreeja, E.; Vidyadharan, Viji; Jose, Saritha K.; George, Anns; Joseph, Cyriac; Unnikrishnan, N. V.; Biju, P. R.

2018-04-01

Pr3+ doped Ba2CaWO6 phosphor were prepared by traditional high-temperature solid-state reaction technique. The structure evolution was systematically investigated by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. The X-ray powder diffraction patterns indicate that the prepared phosphors crystallized in the cubic double-perovskite structure. The functional groups were identified using FTIR spectra and the elements present in the composition were confirmed by the EDS profile. The morphology of the phosphor was identified using SEM and TEM analysis. The PL spectra illustrated that these phosphors could be efficiently excited by charge transfer band of host and the maximum luminescence intensity was observed at 0.06 wt% of Pr3+ ion. Upon the charge transfer band excitation, emission spectra showed peaks at 489, 532, 647, 685 and 737 nm corresponding to 3P0→3H4, 3P1→3H5, 3P0→3F2, 3P0→3F3 and 3P0→3F4 transitions respectively. The concentration quenching of Ba2CaWO6:Pr3+ phosphor can be mainly attributed to dipole-dipole interaction. The CIE coordinates were estimated to be close to the white region. The decay curves are well fitted with double exponential decay models. The standard and modified Judd-Ofelt (JO) theories were used to determine the Judd-Ofelt intensity parameters, radiative transition probabilities and branching ratios. The optical properties indicate that Ba2CaWO6:Pr3+ phosphors can produce white light emission from a single phase host and its potential application for solid-state lighting and display devices.

Concentration Dependence of Luminescent Properties for Sr2TiO4:Eu3+ Red Phosphor and Its Charge Compensation

Directory of Open Access Journals (Sweden)

Zhou Lu

2012-01-01

Full Text Available Sr2TiO4:Eu3+ phosphors using M+ (M = Li+, Na+, and K+ as charge compensators were prepared by the solid-state reaction. The powders were investigated by powder X-ray diffraction (XRD and photoluminescence spectra (PL to study the phase composition, structure, and luminescent properties. The results showed that Li+ ion was the best charge compensator. The phase was Sr2TiO4 when the doping concentration was small (x≤10.0%. When x reached 15.0%, the phase turned into Sr3Ti3O7 because of the structure damage. The phosphor could be effectively excited by ultraviolet (365, 395 nm and blue light (465 nm, and thenitemitted intense red light that peaked at around 620 nm (5D0→7F2. In addition, the emission of 700 nm (5D0→7F4 enhanced the red light color purity. The CIE chromaticity coordinates of samples with the higher red emission were between (0.650, 0.344 and (0.635, 0.352. Doped layered titanate Sr2TiO4:Eu3+ is a promising candidate red phosphor for white LEDs which can be suited for both near-UV LED chip and blue LED chip.

Luminescence and energy transfer of Tm3+ or/and Dy3+ co-doped in Sr3Y(PO4)3 phosphors with UV excitation for WLEDs

International Nuclear Information System (INIS)

Wang, Jiyou; Wang, Jianbo; Duan, Ping

2014-01-01

Powder samples Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ -yDy 3+ were synthesized by the conventional solid-state reaction method. By appropriate tuning of activator content, the emission color can be adjusted around blue to white and yellow. It was discovered that the energy transfer from Tm 3+ to Dy 3+ was demonstrated to be via the intensity of Dy 3+ emission increase with the increase of Tm 3+ concentration. By changing the doping concentration of Tm 3+ and Dy 3+ in Sr 3 Y(PO 4 ) 3 , white-emitting phosphors are produced by 350 nm excitation wavelength, their corresponding color coordinates are very close to the white color chromaticity coordinates (x=0.33, y=0.33). Finally, Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ −yDy 3+ phosphors could be a good promising single-component white light-emitting UV-convertible phosphor in the field of white LEDs. -- Highlights: • The Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ −yDy 3+ phosphors were synthesized by the conventional solid-state reaction method. • The energy transfer in between Tm 3+ and Dy 3+ was observed and explained. • The phosphors can be efficiently excited by a UV light. • The Sr 3 Y 1−x−y (PO 4 ) 3 :xTm 3+ -yDy 3+ phosphor could be a better candidate white phosphor for UV W-LEDs

Luminescence properties of Eu{sup 2+} doped SrB{sub 4}O{sub 7} phosphor for radiation dosimetry

Energy Technology Data Exchange (ETDEWEB)

Palan, C.B., E-mail: chetanpalan27@yahoo.in; Bajaj, N.S.; Omanwar, S.K.

2016-04-15

Highlights: • Report TL/OSL properties of SrB{sub 4}O{sub 7}:Eu{sup 2+} under beta irradiations. • OSL Sensitivity was about 33% than that of commercially available α-Al{sub 2}O{sub 3.} • TL glow peaks was appear at 305° C and TL sensitivity about 200 times higher than TLD-500. • OSL decay pattern was faster than α- Al{sub 2}O{sub 3}:C and dose response was linear nature. - Abstract: In this report, we presented the TL/OSL properties of Eu doped SrB{sub 4}O{sub 7} phosphor under β-irradiation. This phosphor was synthesized by using solid state method. The phosphor shows OSL sensitivity about 33% than that of commercially available α-Al{sub 2}O{sub 3}: C phosphor. CW-OSL curve possess two components having photoionization cross-sections 0.707 × 10{sup −17} and 18.58 × 10{sup −17} cm{sup 2} respectively and TL sensitivity about 200 times higher than TLD-500. The kinetic parameters such as activation energy, frequency factor and order of kinetics of TL curve were calculated by using peak shape method. In TL/OSL mode dose-response was almost linear in the range of measurements. The MDD was found to be 1.26 mGy with 3σ of background. Also reusability studies showed the phosphor can be reused for 10 cycles with 1% change in the OSL output. The PL spectra of SrB{sub 4}O{sub 7} showed emission in NUV region when excited with 318 nm under UV source.

Luminescence properties of Eu2+-doped MAl2-xSixO4-xNx (M = Ca, Sr, Ba) conversion phosphor for white LED applications

NARCIS (Netherlands)

Li, Y.Q.; With, de G.; Hintzen, H.T.J.M.

2006-01-01

Undoped and Eu-doped MAl2-xSixO4-2Nx (M = Ca, Sr, Ba) were synthesized by a solid-state reaction method at 1300 - 1400 ¿C under nitrogen-hydrogen atmosphere. The solubility of (SiN)+, in MAl2O4 was determined. Nitrogen can be incorporated into MAl2O4 by replacement of (AlO)+ by (SiN)+, whose amount

Blue to bluish-green tunable phosphor Sr2LiSiO4F:Ce3+,Tb3+ and efficient energy transfer for near-ultraviolet light-emitting diodes

International Nuclear Information System (INIS)

Xie, Mubiao; Zeng, Lihua; Ye, TingLi; Yang, Xi; Zhu, Xianmei; Peng, Siyun; Lei, Lei

2014-01-01

Ce 3+ and Tb 3+ activated Sr 2 LiSiO 4 F phosphors were prepared by a solid state reaction technique at high temperature, and their ultraviolet (UV)-visible spectroscopic properties were investigated. Under ultraviolet light excitation, Ce 3+ -doped Sr 2 LiSiO 4 F phosphors emit blue light (420 nm), while Tb 3+ -doped phosphors show yellowish green emission. Efficient energy transfer from Ce 3+ to Tb 3+ ions in co-doped samples was confirmed in terms of corresponding excitation and emission spectra. The energy transfer mechanism between Ce 3+ and Tb 3+ was discussed and demonstrated to be dipole–dipole interaction in Sr 2 LiSiO 4 F:Ce 3+ ,Tb 3+ phosphors. Due to energy transfer from Ce 3+ to Tb 3+ , Ce 3+ and Tb 3+ co-doped Sr 2 LiSiO 4 F phosphors show intense absorption in near-UV region, and present tunable emission from blue to bluish green under 360 nm light excitation. The results indicate that these phosphors can be considered as candidates for white LEDs pumped by n-UV chips. (paper)

Reverse micellar synthesis, structural characterization and dielectric properties of Sr-doped BaZrO_3 nanoparticles

International Nuclear Information System (INIS)

Ahmad, Tokeer; Ubaidullah, Mohd; Shahazad, Mohd; Kumar, Dinesh; Al-Hartomy, Omar A.

2017-01-01

Sr-doped BaZrO_3 nanoparticles with strontium content varying from 5 to 20 mol % were successfully synthesized by reverse micellar method at 900 °C for the first time. Systematic studies have been carried out to establish the structural and electrical properties of the as prepared nanoparticles. These nanoparticles were characterized using powder X-ray diffraction, transmission electron microscopy, BET surface area and dielectric measurements. X-ray diffraction analysis showed the formation of monophasic and highly crystalline nanoparticles which could be indexed in cubic BaZrO_3 with contraction of lattice on strontium substitution. A monotonic shift of diffraction pattern towards higher angel confirms the formation of solid solutions of Ba_1_−_xSr_xZrO_3 (0.05 ≤ x ≤ 0.20) which was corroborating well with lattice parameter studies. Transmission electron microscopic studies showed the formation of cubic, spherical and hexagonal nanoparticles with an average grain size of 40–65 nm. Energy dispersive X-ray spectroscopic studies confirmed the presence of dopant (Sr"2"+) in the BaZrO_3 matrix and estimated chemical species corroborate well with the loaded composition. Specific surface area of the solid solution comes out to be in the range of 104–244 m"2 g"-"1. Smallest particle of size 40 nm shows highest surface area 244 m"2 g"-"1 for 20 mol% Sr-doped BaZrO_3. Dielectric and impedance studies were also carried out as a function of frequency and temperature to explore the electrical properties of Sr-doped BaZrO_3. The dielectric constant of Ba_1_−_xSr_xZrO_3 (0.05 ≤ x ≤ 0.20) was found to be in the range of 13–25 for x = 0.05 to x = 0.20 with nearly similar dielectric loss of the order of 0.02. The conductance increases linearly with increase in frequency at room temperature, however the impedance has an inverse effect. - Highlights: • Monophasic nanocrystalline Ba_1_−_xSr_xZrO_3 at low dopant concentration using reverse micelles for the first

Study of chromites YbMIICr2O5,5 (MII - Mg, Ca, Sr, Ba by X-ray diffraction

Directory of Open Access Journals (Sweden)

B. Kasenov

2012-03-01

Full Text Available Compounds of composition YbMeMnFeO5,5 (Me – Mg, Ca, Sr, Ba are synthesized from Yb2O3, , Cr2O3 and MgCO3, CaCO3, SrCO3, BaCO3 by solid phase method. X-ray powder diffraction showed that the compound YbMgCr2O5,5, YbCaCr2O5,5, YbSrCr2O5,5, YbBaCr2O5,5 crystallizes in the tetragonal crystal system.

White light emission and effect of annealing on the Ho3+–Yb3+ codoped BaCa2Al8O15 phosphor

International Nuclear Information System (INIS)

Kumari, Astha; Rai, Vineet Kumar

2015-01-01

Graphical abstract: The upconversion emission spectra of the Ho 3+ /Yb 3+ doped/codoped BaCa 2 Al 8 O 15 phosphors with different doping concentrations of Ho 3+ /Yb 3+ ions along with UC emission spectrum of the white light emitting phosphor annealed at 800 °C. - Highlights: • BaCa 2 Al 8 O 15 phosphors codoped with Ho 3+ –Yb 3+ have been prepared by combustion method. • Phosphor annealed at 800 °C, illuminate an intense white light upon NIR excitation. • The sample annealed at higher temperatures emits in the pure green region. • The colour emitted persists in the white region even at high pump power density. • Developed phosphor is suitable for making upconverters and WLEDs. - Abstract: The BaCa 2 Al 8 O 15 (BCAO) phosphors codoped with suitable Ho 3+ –Yb 3+ dopant concentration prepared by combustion method illuminate an intense white light upon near infrared diode laser excitation. The structural analysis of the phosphors and the detection of impurity contents have been performed by using the X-Ray Diffraction, FESEM and FTIR analysis. The purity of white light emitted from the sample has been confirmed by the CIE chromaticity diagram. Also, the white light emitted from the sample persists with the variation of pump power density. The phosphors emit upconversion (UC) emission bands in the blue, green and red region (three primary colours required for white light emission) along with one more band in the near infrared region of the electromagnetic spectrum. On annealing the white light emitting sample at higher temperatures, the sample starts to emit green colour and also the intensity of green and red UC emission bands get enhanced largely.

Luminescent characteristics of UV excited Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: Pr{sup 3+} reddish-orange phosphor

Energy Technology Data Exchange (ETDEWEB)

Vidyadharan, Viji; Mohan P, Remya; Joseph, Cyriac; Unnikrishnan, N.V.; Biju, P.R., E-mail: prb.mgu@gmail.com

2016-02-15

Pr{sup 3+} doped Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3} phosphors were synthesised by solid state reaction process. The structure, surface morphology and photoluminescence of the prepared phosphors were analysed using XRD, SEM and photoluminescence spectroscopy respectively. The XRD pattern confirmed orthorhombic perovskite structure of the Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: x Pr{sup 3+} phosphor. Agglomeration of particles with irregular shapes is observed from the SEM images. The emission spectra of Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: x Pr{sup 3+} phosphor shows the samples can be effectively excited with UV light at 336 nm and exhibit a strong reddish-orange emission at 611 nm. Concentration dependence of emission intensity shows concentration quenching effect on increasing Pr{sup 3+} concentration after x = 0.1 because of dipole–dipole interaction. Using Blasse's formula, critical distance for energy transfer was calculated. The CIE co-ordinates, CCT, colour purity and luminescence decay of the prepared phosphors were also calculated. These results offer the prepared phosphor as a suitable candidate for various photonic applications. - Highlights: • Sr{sub 0.5}Ca{sub 0.5}TiO{sub 3}: x Pr{sup 3+} perovskite structured phosphors were synthesized. • Under UV excitation, the PL spectra show strong reddish-orange emission. • The emission from {sup 3}P{sub J} levels of Pr{sup 3+} were absent due to the presence of IVCT band. • Concentration quenching due to dipole–dipole interaction was observed. • For x = 0.1, sample shows a maximum emission intensity with 91.7% colour purity.

Facile solution-precipitation assisted synthesis and luminescence property of greenish-yellow emitting Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Ji, Haipeng [School of Materials Science and Technology, Beijing Key Laboratory of Materials Utilization of Nonmetallic Minerals and Solid Wastes, National Laboratory of Mineral Materials, China University of Geosciences, Beijing 100083 (China); Huang, Zhaohui, E-mail: huang118@cugb.edu.cn [School of Materials Science and Technology, Beijing Key Laboratory of Materials Utilization of Nonmetallic Minerals and Solid Wastes, National Laboratory of Mineral Materials, China University of Geosciences, Beijing 100083 (China); Xia, Zhiguo, E-mail: xiazg@ustb.edu.cn [The Beijing Municipal Key Laboratory of New Energy Materials and Technologies, School of Materials Sciences and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Xie, Yao [School of Materials Science and Technology, Beijing Key Laboratory of Materials Utilization of Nonmetallic Minerals and Solid Wastes, National Laboratory of Mineral Materials, China University of Geosciences, Beijing 100083 (China); Molokeev, Maxim S. [Laboratory of Crystal Physics, Kirensky Institute of Physics, SB RAS, Krasnoyarsk 660036 (Russian Federation); Department of Physics, Far Eastern State Transport University, Khabarovsk 680021 (Russian Federation); Atuchin, Victor V. [Laboratory of Optical Materials and Structures, Institute of Semiconductor Physics, SB RAS, Novosibirsk 630090 (Russian Federation); Functional Electronics Laboratory, Tomsk State University, Tomsk 634050 (Russian Federation); Laboratory of Semiconductor and Dielectric Materials, Novosibirsk State University, Novosibirsk 630090 (Russian Federation)

2016-03-15

Highlights: • Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphor was prepared by the solution-precipitation assisted route. • The phosphors have satisfactory smooth grain surface and particle size. • It shows greenish-yellow color emission (maximum at 540 nm) upon blue light excitation. • Eu{sup 2+} is coordinated with isolated oxygen atoms and those from PO{sub 4} polyhedra. - Abstract: Greenish-yellow emitting microcrystalline Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphor was successfully prepared by a solution-precipitation assisted high temperature reaction method. Phase structure, morphology and/or luminescence properties of the precursor and the as-prepared phosphors were characterized. The phase-pure Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} phosphors were obtained with smooth grain surface and particle size of 2–8 μm. Ca{sub 6}Ba(PO{sub 4}){sub 4}O:Eu{sup 2+} exhibits bright greenish-yellow color emission with its maximum at 540 nm upon UV-blue light excitation. The maximum position of the broad emission band is independent on the calcination temperature. The emission intensity increases with increasing calcination temperature due to improved crystallinity. Besides, the presence of two Eu{sup 2+} emission centers in the Ca{sub 6}Ba(PO{sub 4}){sub 4}O crystal lattice was confirmed and the coordination effects are considered concerning the roles of isolated O atoms and those from the PO{sub 4} tetrahedra.

The effects of re-firing process under oxidizing atmosphere and temperatures on the properties of strontium aluminate phosphors

International Nuclear Information System (INIS)

Karacaoglu, Erkul; Karasu, Bekir

2013-01-01

Graphical abstract: The comparative emission spectra of standard and re-fired Phosphor A under oxidizing atmosphere at various temperatures. The colour of Phosphor A re-fired at higher temperatures above 900 °C shifted from yellowish-green to bluish-green in the dark. But, the bluish-green emission could only be seen when it was exposed to UV and disappeared as soon as the light source was removed. Moreover, the emission intensities decreased as the re-firing temperatures increased. This could be attributed to the oxidation of Eu 2+ during the re-firing process. It is well known fact from the literature that the reduction of Eu 3+ to Eu 2+ in appropriate host materials needs an annealing process in a reducing atmosphere such as H 2 , H 2 /N 2 mixture or CO. Up to now, the reduction phenomena of Eu 3+ → Eu 2+ in air have been found in phosphates (Ba 3 (PO 4 ) 2 :Eu), sulphates (BaSO 4 :Eu), borates (SrB 4 O 7 :Eu, SrB 6 O 10 :Eu and BaB 8 O 13 :Eu) and aluminates (Sr 4 Al 14 O 25 :Eu). Interestingly, an apparent blue shift in the phosphorescence spectrum was observed in the samples re-fired at 1000 °C and above, indicating a minimal effect on the oxidation state or the electronic energy levels of the co-doped Dy 3+ ions, which were thought to act as long-lived hole traps resulting in long afterglow. - Highlights: • This study examines the effects re-firing at oxidizing atmosphere of photoluminescence of three different commercial SrAl 2 O 4 :Eu 2+ ,Dy 3+ -phosphors. • All the commercial SrAl 2 O 4 :Eu 2+ ,Dy 3+ -phosphors completely lost their phosphorescence after being re-fired at 1300 °C. • Oxidizing environment and re-firing temperature naturally affecting the valance of Eu 2+ may cause the basic lattice structure to be modified and also limit their applications at higher temperatures, such as third firing vetrosa décor or glaze applications in ceramic industry. • It was thought that this kind of study may be promising to provide many outcome

Luminescent Properties of Sr4Si3O8Cl4:Eu2+, Bi3+ Phosphors for Near UV InGaN-Based Light-Emitting-Diodes

Directory of Open Access Journals (Sweden)

Wangqing Shen

2015-12-01

Full Text Available Sr4Si3O8Cl4 co-doped with Eu2+, Bi3+ were prepared by the high temperature reaction. The structure and luminescent properties of Sr4Si3O8Cl4:Eu2+, Bi3+ were investigated. With the introduction of Bi3+, luminescent properties of these phosphors have been optimized. Compared with Sr3.90Si3O8Cl4:0.10Eu2+, the blue-green phosphor Sr3.50Si3O8Cl4:0.10Eu2+, 0.40Bi3+ shows stronger blue-green emission with broader excitation in near-UV range. Bright blue-green light from the LED means this phosphor can be observed by the naked eye. Hence, it may have an application in near UV LED chips.

Luminescent properties of MAl(SO4)2 Br:Eu(3+) (M = Sr or Mg) red phosphors for near-UV light-emitting diodes.

Science.gov (United States)

Deshmukh, Priti B; Puppalwar, S P; Dhoble, N S; Dhoble, S J

2015-02-01

Eu(3+) -activated MAl(SO4 )2 Br phosphors (where M = Mg or Sr) are successfully prepared using a wet chemical reaction technique. The samples are characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectroscopies. The XRD pattern revealed that both the samples are microcrystalline in nature. PL of Eu(3+) -doped SrAl(SO4 )2 Br and MgAl(SO4 )2 Br phosphors exhibited characteristic red emission coming from the (5) D0  → (7) F2 (616 nm) electron transition, when excited by 396 nm wavelength of light. The maximum intensity of luminescence was observed at a concentration of 1 mol% Eu(3+) . The intensity of the electric dipole transition at 616 nm is greater than that of the magnetic dipole transition at 594 nm. The results showed that MAl(SO4 )2 Br:Eu(3+) , (M = Mg, Sr) phosphors have potential application in near-UV light-emitting diodes as efficient red-emitting phosphor. Copyright © 2014 John Wiley & Sons, Ltd.

Influence of Ba2+ and Sr2+ ions on the hydration process of portland cement and blended cements

Directory of Open Access Journals (Sweden)

Živanović, B. M.

1987-12-01

Full Text Available This study concerns the influence of the concentration of Sr2+ and Ba2+ ions in mortar batch waters upon the hydration process of various Portland and additive cements. An increase in the mechanical resistence of said cements is observed, after 28 days, when the concentration of Ba2+ and Sr2+ ions in the mortar batch waters increases. This suggests a possible microstructural explanation of said phenomenon.En el presente trabajo se estudia la influencia de la concentración de los iones Sr2+ y Ba2+ en las aguas de amasado sobre el proceso de hidratación de varios cementos portland y de adición. Se comprueba un incremento de las resistencias mecánicas de dichos cementos, a los 28 días, cuando aumenta la concentración de los iones Ba2+ y Sr2+ en las aguas de amasado, lo cual sugiere una posible explicación microestructural a dicho fenómeno.

UVB emitting LiSrBO3 phosphor for phototherapy lamp

Science.gov (United States)

Kunghatkar, R. G.; Hemne, P. S.; Dhoble, S. J.

2018-05-01

LiSrBO3 doped Gadolinium have been synthesized by sol gel technique. The formation of host was confirmed by XRD techniques. The incorporation of Gd3+ was confirmed by photoluminescence (PL) characterization. The UVB emission is observed at 316 nm when UV excited by 274 nm. The second order emission are also observed in PL emission spectra at 612 nm and 627 nm. Energy band gap is found to be 5.81 eV by using Kubelka - Munk function. The UVB emission at 316 nm of Gd3+ doped materials are used as phototherapy lamp phosphor.

Synthesis and photoluminescence properties of microcrystalline Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu, Dy, Sm and Pr) phosphors

Energy Technology Data Exchange (ETDEWEB)

Dabre, K.V. [Department of Physics, Arts, Commerce and Science College, Koradi, Nagpur 441111 (India); Park, K. [Faculty of Nanotechnology and Advanced Materials Engineering, Sejong University, Seoul 143-747 (Korea, Republic of); Dhoble, S.J., E-mail: sjdhoble@rediffmail.com [Department of Physics, R.T.M. Nagpur University, Nagpur 440033 (India)

2014-12-25

Graphical abstract: CIE chromaticity coordinate diagram (1931) indicating different colors of Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu (a), Dy (b and c), Sm (d–f) and Pr (g and h)) phosphor under different excitation 466 nm (a), 312 nm (b), 454 nm (c), 313 nm (d), 408 nm (e), 482 nm (f), 315 nm (g) and 450 nm (h). - Highlights: • Microcrystalline Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu, Dy, Sm and Pr) phosphors were synthesized by solid state method. • Photoluminescence properties of phosphor were investigated. • Color of the phosphor for different excitation has been verified by chromaticity diagram. • The host absorption and energy transfer were investigated. - Abstract: The novel microcrystalline Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu, Dy, Sm and Pr) phosphors were synthesized by solid-state reaction method at 1250 °C and their photoluminescence properties were investigated. The Eu{sup 3+} and Dy{sup 3+} activated phosphors show intense red (616 nm) and yellow (574 nm) emission respectively; which indicate that the rare earth ions are substituted at non-centrosymmetric site in the host lattice. Near white (Dy{sup 3+}) and reddish-orange (Sm{sup 3+}) emissions of rare earth ions in the host lattice show strong host absorption and energy transfer from the host to activator ion. Pr{sup 3+} activated phosphor shows a series of emission peaks in the visible region with the most intense peak in the blue region at 491 and 499 nm.

Sol–gel assisted synthesis and photoluminescence property of Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+}, Dy{sup 3+} red phosphor for white light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wentao, E-mail: zhangwentao2005@163.com [College of Materials and Chemistry & Chemical Engineering, Chengdu University of Technology, Chengdu 610059 (China); Mineral Resources Chemistry Key Laboratory of Sichuan Higher Education Institutions, Chengdu 610059 (China); Wang, Yulong; Gao, Yang [College of Materials and Chemistry & Chemical Engineering, Chengdu University of Technology, Chengdu 610059 (China); Long, Jianping [College of Materials and Chemistry & Chemical Engineering, Chengdu University of Technology, Chengdu 610059 (China); Mineral Resources Chemistry Key Laboratory of Sichuan Higher Education Institutions, Chengdu 610059 (China); Li, Junfeng [College of Materials and Chemistry & Chemical Engineering, Chengdu University of Technology, Chengdu 610059 (China)

2016-05-15

Eu{sup 2+}, Dy{sup 3+} co-doped Sr{sub 2}Si{sub 5}N{sub 8} red phosphors were prepared using a sol–gel-nitridation method at a lower temperature comparing with traditional solid state reaction. Effects of synthesis process, Eu{sup 2+} and Dy{sup 3+} doping concentration on the crystal structure and luminescence property of as-prepared phosphors were investigated. X-ray diffraction patterns indicated that all Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+}, Dy{sup 3+} phosphors have the standard phase of Sr{sub 2}Si{sub 5}N{sub 8} structure. With a broad excitation from UV to blue light, a strong emission of Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+}, Dy{sup 3+} with 4f{sup 6}5d{sup 1}→4f{sup 7} transition of Eu{sup 2+} ions was obtained at red region in photoluminescence spectra. Emission peaks in spectra were red-shifted from 611 to 632 nm for all Sr{sub 2}Si{sub 5}N{sub 8}:xEu{sup 2+} as Eu{sup 2+} ion concentrations increased, which due to Eu{sup 2+} ions occupying from the tenfold coordinated site (Sr1) to the eightfold coordinated site (Sr2). These Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+} phosphors with Dy{sup 3+} co-doping showed excellent luminescence properties, included emission intensity and luminescence quenching. It is potential that Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+}, Dy{sup 3+} phosphors can be applied in white LEDs combining with blue InGaN LEDs. - Highlights: • Eu{sup 2+}/Dy{sup 3+} co-doped Sr{sub 2}Si{sub 5}N{sub 8} red phosphor were prepared by sol–gel-nitridation. • Sol–gel-nitridation method decreased the crystallization temperature of Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+}, Dy{sup 3+} effectively. • Luminescence properties of Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+} were improved obviously by Dy{sup 3+} co-doping. • Luminescence properties of Sr{sub 2}Si{sub 5}N{sub 8}:Eu{sup 2+}, Dy{sup 3+} phosphors are superior to commercial Y{sub 2}O{sub 2}S:Eu{sup 3+}.

Luminescent Enhancement of Na+ and Sm3+ Co-doping Reddish Orange SrCa3Si2O8 Phosphors

Science.gov (United States)

Chun, Fengjun; Zhang, Binbin; Li, Wen; Liu, Honggang; Deng, Wen; Chu, Xiang; Osman, Hanan; Zhang, Haitao; Yang, Weiqing

2018-04-01

Reddish orange SrCa3Si2O8 phosphors, prepared by the facile solid state reaction method, are a luminescent enhancement of Na+ and Sm3+ co-doping luminescent material. Na+ was designed to compensate the charge imbalance of Sm3+ ion substituting for the Sr2+ ion of orthorhombic SrCa3Si2O8 crystals. The results suggest that Na+ can effectively enhance the luminescent intensity of the reddish orange light peaked at about 562 nm (4 G 5/2 → 6 H 5/2), 600 nm (4 G 5/2 → 6 H 7/2) and 645 nm (4 G 5/2 → 6 H 9/2) excited by the near ultraviolet excited light 404 nm (4 L 13/2 → 6 H 5/2). The energy transfer has been further verified by the florescence lifetime. Additionally, the luminescent lifetime τ of as-grown phosphors was separated into two parts, a rapid lifetime and a slow lifetime. The average lifetime results ranged from 2.098 to 1.329 ms which were influenced by the concentration of Sm3+ doping. The systematic researches of as-grown phosphors have clearly suggested a potential application for white-light-emitting diodes ( w-LEDs).

Formation of layered microstructure in the Y-Ba-Cu-O and Bi-Sr-Ca-Cu-O superconductors

International Nuclear Information System (INIS)

Jin, S.; Kammlott, G.W.; Tiefel, T.H.; Chen, S.K.

1992-01-01

The layered grain microstructure is essential for overcoming the weak link problem and ensuring high transport critical currents in the cuprate superconductors. In this paper we discuss the processing and the mechanisms for layer information in Y-Ba-Cu-O and Bi-Sr-Ca-Cu-O. In melt-processed Y-Ba-Cu-O, sympathetic nucleation on previously nucleated YBa 2 Cu 3 O 7-δ plates during solidification appears to be dominant mechanism for the formation of parallel plate-shaped grains. In the Y-Ba-Cu-O and Bi-Sr-Ca-Cu-O ribbons, the interface reaction between the superconductor layer and the silvers substrate seems to be the main mechanism for the c-axis texturing of the layered grains. The drastically different critical current behavior in the c-axis textured Y-Ba-Cu-O and Bi-Sr-Ca-Cu-O ribbons is discussed in terms of possible differences in the nature of the twist and tilt grain boundaries. (orig.)

Crystal structures of the double perovskites Ba2Sr1-x Ca x WO6

International Nuclear Information System (INIS)

Fu, W.T.; Akerboom, S.; IJdo, D.J.W.

2007-01-01

Structures of the double perovskites Ba 2 Sr 1- x Ca x WO 6 have been studied by the profile analysis of X-ray diffraction data. The end members, Ba 2 SrWO 6 and Ba 2 CaWO 6 , have the space group I2/m (tilt system a 0 b - b - ) and Fm3-barm (tilt system a 0 a 0 a 0 ), respectively. By increasing the Ca concentration, the monoclinic structure transforms to the cubic one via the rhombohedral R3-bar phase (tilt system a - a - a - ) instead of the tetragonal I4/m phase (tilt system a 0 a 0 c - ). This observation supports the idea that the rhombohedral structure is favoured by increasing the covalency of the octahedral cations in Ba 2 MM'O 6 -type double perovskites, and disagrees with a recent proposal that the formation of the π-bonding, e.g., d 0 -ion, determines the tetragonal symmetry in preference to the rhombohedral one. - Graphical abstract: Enlarged sections showing the evolution of the basic (222) and (400) reflections in Ba 2 Sr 1- x Ca x WO 6 . Tick marks below are the positions of Bragg's reflections calculated using the space groups I2/m (x=0), R3-bar (x=0.25, 0.5 and 0.75) and Fm3-barm (x=1), respectively

A novel yellow-emitting SrAlSi4N7:Ce3+ phosphor for solid state lighting: Synthesis, electronic structure and photoluminescence properties

Science.gov (United States)

Ruan, Jian; Xie, Rong-Jun; Funahashi, Shiro; Tanaka, Yoshinori; Takeda, Takashi; Suehiro, Takayuki; Hirosaki, Naoto; Li, Yuan-Qiang

2013-12-01

Ce3+-doped and Ce3+/Li+-codoped SrAlSi4N7 phosphors were synthesized by gas pressure sintering of powder mixtures of Sr3N2, AlN, α-Si3N4, CeN and Li3N. The phase purity, electronic crystal structure, photoluminescence properties of SrAlSi4N7:Ce3+(Ce3+/Li+) were investigated in this work. The band structure calculated by the DMol3 code shows that SrAlSi4N7 has a direct band gap of 3.87 eV. The single crystal analysis of Ce3+-doped SrAlSi4N7 indicates a disordered Si/Al distribution and nitrogen vacnacy defects. SrAlSi4N7 was identified as a major phase of the fired powders, and Sr5Al5Si21N35O2 and AlN as minor phases. Both Ce3+ and Ce3+/Li+ doped SrAlSi4N7 phosphors can be efficiently excited by near-UV or blue light and show a broadband yellow emission peaking around 565 nm. A highest external quantum efficiency of 38.3% under the 450 nm excitation was observed for the Ce3+/Li+-doped SrAlSi4N7 (5 mol%). A white light LED lamp with color temperature of 6300 K and color rendering index of Ra=78 was achieved by combining Sr0.97Al1.03Si3.997N\\94\\maccounttest14=t0005_18193 7:Ce3+0.03 with a commercial blue InGaN chip. It indicates that SrAlSi4N7:Ce3+ is a promising yellow emitting down-conversion phosphor for white LEDs.

Structural, electronic and optical characteristics of SrGe{sub 2} and BaGe{sub 2}: A combined experimental and computational study

Energy Technology Data Exchange (ETDEWEB)

Kumar, Mukesh, E-mail: mkgarg79@gmail.com [Environmental Remediation Materials Unit, National Institute for Materials Science, Ibaraki 305-0044 (Japan); Umezawa, Naoto [Environmental Remediation Materials Unit, National Institute for Materials Science, Ibaraki 305-0044 (Japan); Imai, Motoharu [Superconducting Properties Unit, National Institute for Materials Science, Ibaraki 305-0047 (Japan)

2015-05-05

Highlights: • Charge transfer between cation and anion atoms observed first time in digermandies. • Study yields a band gap of ∼1 eV and ∼0.85 eV for SrGe{sub 2} and BaGe{sub 2}, respectively. • Band gap decrease with the application of hydrostatic pressure. • Localized cation d states lead to a large absorption coefficient (>7.5 × 10{sup 4} cm{sup −1}). - Abstract: SrGe{sub 2} and BaGe{sub 2} were characterized for structural, electronic and optical properties by means of diffuse reflectance and first-principles density functional theory. These two germanides crystallize in the BaSi{sub 2}-type structure, in which Ge atoms are arranged in tetrahedral configuration. The calculation indicates a charge transfer from Sr (or Ba) atoms to Ge atoms along with the formation of covalent bonds among Ge atoms in Ge tetrahedral. The computational results confirm that these two germanies are Zintl phase described as Sr{sub 2}Ge{sub 4} (or Ba{sub 2}Ge{sub 4}), which are characterized by positively charged [Sr{sub 2} (or Ba{sub 2})]{sup 2.59+} and negatively charged [Ge{sub 4}]{sup 2.59−} units acting as cation and anion, respectively. These compounds are indirect gap semiconductors with band gap estimated to be E{sub g} = 1.02 eV for BaGe{sub 2} and E{sub g} = 0.89 eV for SrGe{sub 2} which are in good agreement with our experimental measured values (E{sub g} = 0.97 eV for BaGe{sub 2} and E{sub g} = 0.82 eV for SrGe{sub 2}). Our calculations demonstrate that the band gaps are narrowed by application of hydrostatic pressure; the pressure coefficients are estimated to be −10.54 for SrGe{sub 2} and −10.06 meV/GPa for BaGe{sub 2}. Optical properties reveal that these compounds have large absorption coefficient (∼7.5 × 10{sup 4} cm{sup −1} at 1.5 eV) and the estimated high frequency (static) dielectric constant are, ε{sub ∞}(ε{sub 0}) ≈ 12.8(20.97) for BaGe{sub 2} and ε{sub ∞}(ε{sub 0}) ≈ 14.27(22.87) for SrGe{sub 2}.

Reverse micellar synthesis, structural characterization and dielectric properties of Sr-doped BaZrO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Tokeer, E-mail: tahmad3@jmi.ac.in [Nanochemistry Laboratory, Department of Chemistry, Jamia Millia Islamia, New Delhi, 110025 (India); Ubaidullah, Mohd [Nanochemistry Laboratory, Department of Chemistry, Jamia Millia Islamia, New Delhi, 110025 (India); Department of Chemistry, Banasthali University, Tonk, Rajasthan, 304022 (India); School of Science and Technology, Glocal University, Mirzapur, Saharanpur, 247121, Uttar Pradesh (India); Shahazad, Mohd [Nanochemistry Laboratory, Department of Chemistry, Jamia Millia Islamia, New Delhi, 110025 (India); Kumar, Dinesh [Department of Chemistry, Banasthali University, Tonk, Rajasthan, 304022 (India); Al-Hartomy, Omar A. [Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah, 21589 (Saudi Arabia)

2017-01-01

Sr-doped BaZrO{sub 3} nanoparticles with strontium content varying from 5 to 20 mol % were successfully synthesized by reverse micellar method at 900 °C for the first time. Systematic studies have been carried out to establish the structural and electrical properties of the as prepared nanoparticles. These nanoparticles were characterized using powder X-ray diffraction, transmission electron microscopy, BET surface area and dielectric measurements. X-ray diffraction analysis showed the formation of monophasic and highly crystalline nanoparticles which could be indexed in cubic BaZrO{sub 3} with contraction of lattice on strontium substitution. A monotonic shift of diffraction pattern towards higher angel confirms the formation of solid solutions of Ba{sub 1−x}Sr{sub x}ZrO{sub 3} (0.05 ≤ x ≤ 0.20) which was corroborating well with lattice parameter studies. Transmission electron microscopic studies showed the formation of cubic, spherical and hexagonal nanoparticles with an average grain size of 40–65 nm. Energy dispersive X-ray spectroscopic studies confirmed the presence of dopant (Sr{sup 2+}) in the BaZrO{sub 3} matrix and estimated chemical species corroborate well with the loaded composition. Specific surface area of the solid solution comes out to be in the range of 104–244 m{sup 2} g{sup -1}. Smallest particle of size 40 nm shows highest surface area 244 m{sup 2} g{sup -1} for 20 mol% Sr-doped BaZrO{sub 3}. Dielectric and impedance studies were also carried out as a function of frequency and temperature to explore the electrical properties of Sr-doped BaZrO{sub 3}. The dielectric constant of Ba{sub 1−x}Sr{sub x}ZrO{sub 3} (0.05 ≤ x ≤ 0.20) was found to be in the range of 13–25 for x = 0.05 to x = 0.20 with nearly similar dielectric loss of the order of 0.02. The conductance increases linearly with increase in frequency at room temperature, however the impedance has an inverse effect. - Highlights: • Monophasic nanocrystalline Ba{sub 1−x}Sr

Photoluminescence properties of color-tunable SrMgAl10O17:Eu2+,Mn2+ phosphors for UV LEDs

International Nuclear Information System (INIS)

Ju Guifang; Hu Yihua; Chen Li; Wang Xiaojuan

2012-01-01

Aluminate phosphors SrMgAl 10 O 17 codoped with Eu 2+ and Mn 2+ ions were prepared by solid-state reaction. The phase structure and photoluminescence properties of the as-prepared phosphors were characterized by powder X-ray diffraction, photoluminescence excitation and emission spectra. Upon excitation of UV light, two broad emission bands centered at 470 and 515 nm were observed, and they were assigned to Eu 2+ and Mn 2+ emissions, respectively. The emission color of the phosphors can be tuned from blue to cyan and finally to green by adjusting the concentration ratios of Eu 2+ and Mn 2+ . Effective energy transfer occurs from Eu 2+ to Mn 2+ in the host due to the spectral overlap between the emission band of Eu 2+ and the excitation bands of Mn 2+ . The energy transfer mechanism was demonstrated to be electric dipole–quadrupole interaction. The energy transfer efficiency and critical distance were also calculated. The phosphors exhibit strong absorption in near UV spectral region and therefore they are potentially useful as UV-convertible phosphors for white LEDs. - Highlights: ► The strong absorption of phosphors matches well with the emission band of UV LED. ► The energy transfer from Eu 2+ to Mn 2+ in SrMgAl 10 O 17 was investigated in detail. ► The emission color can be tuned by adjusting the content of Eu 2+ and Mn 2+ . ► Two methods were employed to calculate the critical distance of energy transfer.

Tunable luminescence properties and energy transfer of Ba{sub 3}NaLa(PO{sub 4}){sub 3}F:Tb{sup 3+},Sm{sup 3+} phosphors with apatite structure

Energy Technology Data Exchange (ETDEWEB)

Liu, Haikun; Liao, Libing, E-mail: clayl@cugb.edu.cn; Chen, Jian; Guo, Qingfeng; Zhang, Yuanyuan; Mei, Lefu, E-mail: mlf@cugb.edu.cn

2016-01-15

Tb{sup 3+}–Sm{sup 3+} co-doped Ba{sub 3}NaLa(PO{sub 4}){sub 3}F phosphors with apatite structure have been prepared by a high temperature solid-state reaction, and their luminescence properties have been investigated in detail. The energy transfer (ET) mechanism was verified as the dipole–quadrupole mechanism, and the ET efficiency as well as the critical distance is also estimated. As a result of fine-tuning of the emission composition of the Tb{sup 3+} and Sm{sup 3+} ions, tunable luminescence properties can be realized by combining the emission of Tb{sup 3+} and Sm{sup 3+} in a single host lattice under UV light excitation. The emission color of the obtained phosphors can be modulated from green to yellow by controlling the doping content of the Sm{sup 3+} ions with the fixed Tb{sup 3+} content. Additional, as the temperature increases from RT to 150 °C, the PL intensities of Ba{sub 3}NaLa{sub 0.7}(PO{sub 4}){sub 3}F:0.10Tb{sup 3+},0.20Sm{sup 3+} decreased to 80.4% and 78.6% of the initial PL intensity, corresponding to the intensity of transition of Sm{sup 3+} and transition of Tb{sup 3+} in the Ba{sub 3}NaLa{sub 0.7}(PO{sub 4}){sub 3}F:0.10Tb{sup 3+},0.20Sm{sup 3+} phosphor, respectively. These results indicate the series of Ba{sub 3}NaLa{sub 1−x−y}(PO{sub 4}){sub 3}F:xTb{sup 3+},ySm{sup 3+} phosphors can be acted as a good candidate for the application in white light-emitting diodes. - Highlights: • Tb{sup 3+},Sm{sup 3+}-codoped Ba{sub 3}NaLa(PO{sub 4}){sub 3}F phosphors have been synthesized. • The emission color of the obtained phosphors can be modulated from green to red. • This phosphor has a good thermal stability.

Thermal expansion behaviour in the oxygen deficient perovskites Sr2BSbO5.5 (B=Ca, Sr, Ba). Competing effects of water and oxygen ordering

International Nuclear Information System (INIS)

Zhou Qingdi; Kennedy, Brendan J.; Avdeev, Maxim

2011-01-01

Neutron diffractions studies reveal the presence of oxygen disorder in the oxygen deficient perovskites Sr 2 BSbO 5.5 (B=Ca, Sr, Ba). Synchrotron X-ray studies demonstrate that these oxides have a double perovskite-type structure with the cell size increasing as the size of the B cation increases from 8.2114(2) A for B=Ca to 8.4408(1) A for B=Ba. It is postulated that a combination of local clustering of the anions and vacancies together with water-water and water-host hydrogen bonds plays a role in defining the volume of the encapsulated water clusters and that changes in the local structure upon heating result in anomalous thermal expansion observed in variable temperature diffraction measurements. - Graphical abstract: The oxides Sr 2 BSbO 5.5 (B=Ca, Sr, Ba) have unusual anion disorder. There is a lag in the contraction in the cell size of Sr 2 CaSbO 5.5 nH 2 O established from X-ray diffraction measurements following the loss of water suggesting changes on the local structure are important. Highlights: → The average structures of the defect perovskites Sr 2 MSbO 5.5 established. → Anion and cation disorder quantified by neutron and synchrotron X-ray diffraction. → Anomalous thermal expansion due to local clustering of anions and vacancies observed.

Color tunable emission through energy transfer from Yb3+ co-doped SrSnO3: Ho3+ perovskite nano-phosphor

Science.gov (United States)

Jain, Neha; Singh, Rajan Kr.; Sinha, Shriya; Singh, R. A.; Singh, Jai

2018-04-01

First time color tunable lighting observed from Ho3+ and Yb3+ co-doped SrSnO3 perovskite. Down-conversion and up-conversion (UC) photoluminescence emission spectra were recorded to understand the whole mechanism of energy migration between Ho3+ and Yb3+ ions. The intensity of green and red emission varies with Yb3+ doping which causes multicolour emissions from nano-phosphor. The intensity of UC red emission (654 nm) obtained from 1 at.% Ho3+ and 3 at.% Yb3+ co-doped nano-phosphor is nine times higher than from 1 at.% Ho3+ doped SrSnO3 nano-phosphor. Enhanced brightness of 654 nm in UC process belongs in biological transparency window so that it might be a promising phosphor in the bio-medical field. Moreover, for the other Yb3+ co-doped nano-phosphor, Commission Internationale de l'Éclairage chromaticity co-ordinates were found near the white region and their CCT values lie in the range 4900-5100 K indicating cool white. Decay time was measured for 545 nm emission of Ho3+ ion found in 7.652 and 8.734 µs at 355 nm excitation. The variation in lifetime was observed in ascending order with increasing Yb3+ concentration which supports PL emission spectra observation that with increasing Yb3+ concentration, rate of transition has changed. These studies reveal that Ho3+ and Yb3+ co-doped phosphor is useful for fabrication of white LEDs.

Luminescence and luminescence quenching of Sr{sub 3}Lu{sub 2}(Si{sub 3}O{sub 9}){sub 2}:Ce{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Mikalauskaite, I.; Raudonyte-Svirbutaviciene, E. [Institute of Chemistry, Faculty of Chemistry and Geosciences, Vilnius University, Naugarduko 24, LT-03225 Vilnius (Lithuania); Linkeviciute, A. [State Research Institute, Centre for Physical Sciences and Technology, Sauletekio Avenue 3, LT-10257 Vilnius (Lithuania); Urbonas, M. [Institute of Chemistry, Faculty of Chemistry and Geosciences, Vilnius University, Naugarduko 24, LT-03225 Vilnius (Lithuania); Katelnikovas, A., E-mail: arturas.katelnikovas@chf.vu.lt [Institute of Chemistry, Faculty of Chemistry and Geosciences, Vilnius University, Naugarduko 24, LT-03225 Vilnius (Lithuania)

2017-04-15

A series of near-UV to blue emitting Sr{sub 3}Lu{sub 2}(Si{sub 3}O{sub 9}){sub 2}:Ce{sup 3+} phosphors were prepared by a solid state reaction. The optical properties of synthesized phosphors were investigated as a function of Ce{sup 3+} concentration and temperature. These luminescent materials strongly absorb UV radiation shorter than 360 nm. The optimal Ce{sup 3+} concentration was 0.1% (external quantum efficiency ca. 45%). Temperature dependent measurements showed that Sr{sub 3}Lu{sub 2}(Si{sub 3}O{sub 9}){sub 2}:Ce{sup 3+} phosphors possess good thermal stability and loses only about 40% to 50% of initial intensity in the temperature range of 77–500 K depending on activator concentration.

Energy transfer and color tunable emission in Tb3+,Eu3+ co-doped Sr3LaNa(PO4)3F phosphors.

Science.gov (United States)

Li, Shuo; Guo, Ning; Liang, Qimeng; Ding, Yu; Zhou, Huitao; Ouyang, Ruizhuo; Lü, Wei

2018-02-05

A group of color tunable Sr 3 LaNa(PO 4 ) 3 F:Tb 3+ ,Eu 3+ phosphors were prepared by conventional high temperature solid state method. The phase structures, luminescence properties, fluorescence lifetimes and energy transfer were investigated in detail. Under 369nm excitation, owing to efficient energy transfer of Tb 3+ →Eu 3+ , the emission spectra both have green emission of Tb 3+ and red emission of Eu 3+ . An efficient energy transfer occur in Tb 3+ , Eu 3+ co-doped Sr 3 LaNa(PO 4 ) 3 F phosphors. The most possible mechanism of energy transfer is dipole-dipole interaction by Dexter's theoretical model. The energy transfer of Tb 3+ and Eu 3+ was confirmed by the variations of emission and excitation spectra and Tb 3+ /Eu 3+ decay lifetimes in Sr 3 LaNa(PO 4 ) 3 F:Tb 3+ ,Eu 3+ . The color tone can tuned from yellowish-green through yellow and eventually to reddish-orange with fixed Tb 3+ content by changing Eu 3+ concentrations. The results show that the prepared Tb 3+ , Eu 3+ co-doped color tunable Sr 3 LaNa(PO 4 ) 3 F phosphor can be used for white LED. Copyright © 2017 Elsevier B.V. All rights reserved.

Energy transfer and color tunable emission in Tb3 +,Eu3 + co-doped Sr3LaNa(PO4)3F phosphors

Science.gov (United States)

Li, Shuo; Guo, Ning; Liang, Qimeng; Ding, Yu; Zhou, Huitao; Ouyang, Ruizhuo; Lü, Wei

2018-02-01

A group of color tunable Sr3LaNa(PO4)3F:Tb3 +,Eu3 + phosphors were prepared by conventional high temperature solid state method. The phase structures, luminescence properties, fluorescence lifetimes and energy transfer were investigated in detail. Under 369 nm excitation, owing to efficient energy transfer of Tb3 + → Eu3 +, the emission spectra both have green emission of Tb3 + and red emission of Eu3 +. An efficient energy transfer occur in Tb3 +, Eu3 + co-doped Sr3LaNa(PO4)3F phosphors. The most possible mechanism of energy transfer is dipole-dipole interaction by Dexter's theoretical model. The energy transfer of Tb3 + and Eu3 + was confirmed by the variations of emission and excitation spectra and Tb3 +/Eu3 + decay lifetimes in Sr3LaNa(PO4)3F:Tb3 +,Eu3 +. The color tone can tuned from yellowish-green through yellow and eventually to reddish-orange with fixed Tb3 + content by changing Eu3 + concentrations. The results show that the prepared Tb3 +, Eu3 + co-doped color tunable Sr3LaNa(PO4)3F phosphor can be used for white LED.

Impedance spectroscopy and structural properties of the perovskite-like Sn(Ba,Sr)O3 stagnate

International Nuclear Information System (INIS)

Cuervo Farfán, J.; Olaya, J.J.; Vera López, E.; Landínez Téllez, D.A.; Roa-Rojas, J.

2012-01-01

An exhaustive study of structural, electrical and transport properties on the perovskite stagnate Sn(Ba,Sr)O 3 was performed. Samples of SnBa 1-x Sr x O 3 with 0≤x≤1.00 were prepared by the solid state reaction method. The crystallographic structure was studied by X-ray diffraction experiments and Rietveld refinement using the GSAS code. Results reveal the material synthesized in a cubic structure (space group Pm3-bar m, no. 221) for 0≤x≤0.50 and in an orthorhombic (space group Pnma, no. 62) for x>0.50. The approximate grain size was found from experiments' Scanning Electron Microscopy. The electric response was studied by the Impedance Spectroscopy technique from 10.0 mHz up to 0,10 MHz. Electric polarization measurements for SnSrO 3 and SnBaO 3 were determined through curves of polarization as a function of applied electric field, which reveal the ferroelectric character of the material. From the saturation polarization the dielectric constants of materials were calculated.

Dielectric behaviour of (Ba,Sr)TiO3 perovskite borosilicate glass ceramics

International Nuclear Information System (INIS)

Yadav, Avadhesh Kumar; Gautam, C.R.

2013-01-01

Various perovskite (Ba,Sr)TiO 3 borosilicate glasses were prepared by rapid melt-quench technique in the glass system ((Ba 1-x Sr x ).TiO 3 )-(2SiO 2 .B 2 O 3 )-(K 2 O)-(La 2 O 3 ). On the basis of differential thermal analysis results, glasses were converted into glass ceramic samples by regulated heat treatment schedules. The dielectric behaviour of crystallized barium strontium titanate borosilicate glass ceramic samples shows diffuse phase transition. The study depicts the dielectric behaviour of glass ceramic sample BST5K1L0.2S814. The double relaxation was observed in glass ceramic samples corresponding 80/20% Ba/Sr due to change in crystal structure from orthorhombic to tetragonal and tetragonal to cubic with variation of temperature. The highest value of dielectric constant was found to be 48289 for the glass ceramic sample BST5K1L0.2S814. The high value of dielectric constant attributed to space charge polarization between the glassy phase and perovskite phase. Due to very high value of dielectric constant, such glass ceramics are used for high energy storage devices. La 2 O 3 acts as nucleating agent for crystallization of glass to glass ceramics and enhances the dielectric constant and retarded dielectric loss. Such glass ceramics can be used in high energy storage devices such as barrier layer capacitors, multilayer capacitors etc. (author)

Elastic properties of nano structured AZrO3 (A=Ba, Sr) single perovskites

International Nuclear Information System (INIS)

Pazhani, R.; Thomas, J.K.; Moses Ezhil Raj, A.; Solomon, S.; Bena Jothy, V.; Mathai, K.C.

2011-01-01

Nanocrystals of barium zirconate and strontium zirconate AZrO 3 (A=Ba and Sr) were synthesized by a unique self-sustained single-step combustion of an aqueous solution, containing Ba, Sr and Zr ions by using citric acid as complexing agent and liquor ammonia as fuel, thus giving rise to phase pure AZrO 3 nanopowder. In this process, a single phase pure nanopowder of AZrO 3 has been obtained without the need of calcination steps. The formation and stability of the compound was confirmed through the tolerance factor on the basis of the ionic radii of all the atoms of the compound. Phase-purity of the as-prepared powders was examined using X-ray diffraction. As-prepared powder was single phase, crystalline, and composed of uniform particles with sizes 20-30 nm. The crystal structure of AZrO 3 are respective cubic (Pm3-bar m, a=4.1839A) and orthorhombic (Pnma, a=5.7937A, b=8.17648A and c=5.7694A). Annealed samples of SrZrO 3 has improved crystal structure with a=5.764A, b=8.2292A and c=5.7989A, comparable to the standards. Microstrain acting on all the planes of the material is positive which indicates presence of tensile stress on the material. The calculated compressive stress on the surface of' the nanopowder is of the order 0.213 GPa to -0.274 GPa for BaZrO 3 and 4.443 GPa to -0.220 GPa for SrZrO 3 along various planes of the particles. (author)

Dependence of transfer number of fluorine on cation type in glasses of Ba(PO3)2-MeF2 systems (Me=Ba,Sr,Ca,Mg)

International Nuclear Information System (INIS)

Pronkin, A.A.

1978-01-01

The influence of Ba, Sr, Ca, Mg cations on transfer numbers of fluorine in glasses of Ba(PO 3 ) 2 - MeF 2 pseudobinary systems is studied. Transfer numbers are essentially different in one and the same fluorine ion concentration in glasses, containing various alkali-earth cations: increase of the cation field force brings about decrease of the transfer numbers of fluorine, and the glass-formation region in the Ba-Sr-Ca-Mg series rises. The dependence of transfer numbers of fluorine on the fluorine concentration logarithm is presented. It is established, that alkali-earth metals influence the transfer numbers of fluorine on account of selective interaction with the phosphate constituent of glass structure

Host composition dependent tunable multicolor emission in the single-phase Ba2(Ln(1-z)Tb(z))(BO3)2Cl:Eu phosphors.

Science.gov (United States)

Xia, Zhiguo; Zhuang, Jiaqing; Meijerink, Andries; Jing, Xiping

2013-05-14

A new strategy based on the host composition design has been adopted to obtain efficient color-tunable emission from Ba2Ln(0.97-z)Tb(z)(BO3)2Cl:0.03Eu (Ln = Y, Gd and Lu, z = 0-0.97) phosphors. This study reveals that the single-phase Ba2Ln(1-z)Tb(z)(BO3)2Cl compounds can be applied to use allowed Eu(2+) absorption transitions to sensitize Eu(3+) emission via the energy transfer Eu(2+) → (Tb(3+))n → Eu(3+). The powder X-ray diffraction (XRD) and Rietveld refinement analysis shows single-phase Ba2Ln(1-z)Tb(z)(BO3)2Cl. As-prepared Ba2Ln(0.97-z)Tb(z)(BO3)2Cl:0.03Eu phosphors show intense green, yellow, orange and red emission under 377 nm near ultraviolet (n-UV) excitation due to a variation in the relative intensities of the Eu(2+), Tb(3+) and Eu(3+) emission depending on the Tb content (z) in the host composition, allowing color tuning. The variation in emission color is explained by energy transfer and has been investigated by photoluminescence and lifetime measurements and is further characterized by the Commission Internationale de l'éclairage (CIE) chromaticity indexes. The quantum efficiencies of the phosphors are high, up to 74%, and show good thermal stabilities up to 150 °C. This investigation demonstrates the possibility to sensitize Eu(3+) line emission by Eu(2+)via energy migration over Tb(3+) resulting in efficient color tunable phosphors which are promising for use in solid-state white light-emitting diodes (w-LEDs).

Investigations of the solid solution in the system SrI2-BaI2 at ambient pressures and at 2.0 GPa

International Nuclear Information System (INIS)

Beck, H.P.; Holley, C.; Limmer, A.

1984-01-01

The P,T,x-diagram of the system SrI 2 -BaI 2 has been investigated at ambient pressures and at 2.0 GPa. The amount of solid solution in the four structure types occuring in this system (SrI 2 - or PbCl 2 -ZrAs 2 -type with SrI 2 and PbCl 2 - or anti-Fe 2 P-type with BaI 2 ) differs considerably. Structural geometries belonging to the same PbCl 2 structure family show marked differences in their toleration to cation substitution. Solid solution is especially pronounced in the BaI 2 -rich phases which incorporate up to 60 mol-% Sr 2+ in the high pressure phase of BaI 2 . (author)

Pyrolysis synthesis of Zn{sub 2}SiO{sub 4}:Mn{sup 2+} phosphors – effect of fuel, flux and co-dopants

Energy Technology Data Exchange (ETDEWEB)

Sivakumar, V.; Lakshmanan, Arunachalam, E-mail: arunachalamlakshmanan@yahoo.com

2014-01-15

Green emitting α-Zn{sub 2}SiO{sub 4}:Mn{sup 2+} phosphors were made by pyrolysis route at 600 °C followed by sintering at a moderate temperature of 1000 °C for 1 h duration. The effects of different fuels (urea, citric acid, polyethylene glycol and glycine), flux materials (H{sub 3}BO{sub 3}, NH{sub 4}Cl, NH{sub 4}F, NH{sub 4}Br, BaCl{sub 2}, BaBr{sub 2}, CaF{sub 2} and BaF{sub 2}), divalant co-dopants (Ca{sup 2+}, Ba{sup 2+}, Mg{sup 2+} and Sr{sup 2+}), trivalent co-dopants (Al{sup 3+}, Y{sup 3+} and Gd{sup 3+}) and sintering temperature (800–1000 °C) on the photoluminescence (PL) efficiency of Zn{sub 2}SiO{sub 4}:Mn{sup 2+} were studied. Among the fuels, urea and among the flux, H{sub 3}BO{sub 3} gave a maximum broad band green PL emission peak at 525 nm on excitation at 254 nm. Divalent co-dopants improved the PL intensity much more than the trivalent co-dopants used. Highest PL efficiency was observed with Sr{sup 2+} co-doped Zn{sub 2}SiO{sub 4}:Mn{sup 2+} sintered at 1000 °C in reducing atmosphere which was 20% higher than that of the commercial Zn{sub 2}SiO{sub 4}:Mn{sup 2+}. The formation of a single crystalline phase of willemite structure in the α-Zn{sub 2}SiO{sub 4}:Mn{sup 2+} samples synthesized was confirmed by powder XRD measurements. -- Highlights: • Zn{sub 2}SiO{sub 4}:Mn{sup 2+} green phosphors were made by pyrolysis route. • Effect of fuel, flux and co dopant on PL intensity. • Enhancement in luminescence with divalent co-dopants, notably Sr. • PL efficiency 20% higher than that of the commercial phosphor. • XRD confirm single phase willemite structure of Zn{sub 2}SiO{sub 4}:Mn{sup 2+}.

Numerical solutions of anharmonic vibration of BaO and SrO molecules

Energy Technology Data Exchange (ETDEWEB)

Pramudito, Sidikrubadi; Sanjaya, Nugraha Wanda [Theoretical Physics Division, Department of Physics, Bogor Agricultural University, Jalan Meranti Kampus IPB Dramaga Bogor 16680 (Indonesia); Sumaryada, Tony, E-mail: tsumaryada@ipb.ac.id [Theoretical Physics Division, Department of Physics, Bogor Agricultural University, Jalan Meranti Kampus IPB Dramaga Bogor 16680 (Indonesia); Computational Biophysics and Molecular Modeling Research Group (CBMoRG), Department of Physics, Bogor Agricultural University, Jalan Meranti Kampus IPB Dramaga Bogor 16680 (Indonesia)

2016-03-11

The Morse potential is a potential model that is used to describe the anharmonic behavior of molecular vibration between atoms. The BaO and SrO molecules, which are two almost similar diatomic molecules, were investigated in this research. Some of their properties like the value of the dissociation energy, the energy eigenvalues of each energy level, and the profile of the wavefunctions in their correspondence vibrational states were presented in this paper. Calculation of the energy eigenvalues and plotting the wave function’s profiles were performed using Numerov method combined with the shooting method. In general we concluded that the Morse potential solved with numerical methods could accurately produce the vibrational properties and the wavefunction behavior of BaO and SrO molecules from the ground state to the higher states close to the dissociation level.

Strong blue and white photoluminescence emission of BaZrO{sub 3} undoped and lanthanide doped phosphor for light emitting diodes application

Energy Technology Data Exchange (ETDEWEB)

Romero, V.H. [Centro de Investigaciones en Optica, A. P. 1-948, Leon Gto., 37160 (Mexico); De la Rosa, E., E-mail: elder@cio.mx [Centro de Investigaciones en Optica, A. P. 1-948, Leon Gto., 37160 (Mexico); Salas, P. [Centro de Fisica Aplicada y Tecnologia Avanzada, Universidad Nacional Autonoma de Mexico, A.P. 1-1010, Queretaro, Qro. 76000 (Mexico); Velazquez-Salazar, J.J. [Department of Physics and Astronomy, The University of Texas at San Antonio One UTSA Circle, San Antonio TX 78249 (United States)

2012-12-15

In this paper, we report the obtained strong broadband blue photoluminescence (PL) emission centered at 427 nm for undoped BaZrO{sub 3} observed after 266 nm excitation of submicron crystals prepared by hydrothermal/calcinations method. This emission is enhanced with the introduction of Tm{sup 3+} ions and is stronger than the characteristic PL blue emission of such lanthanide. The proposed mechanism of relaxation for host lattice emission is based on the presence of oxygen vacancies produced during the synthesis process and the charge compensation due to the difference in the electron valence between dopant and substituted ion in the host. Brilliant white light emission with a color coordinate of (x=0.29, y=0.32) was observed by combining the blue PL emission from the host with the green and red PL emission from Tb{sup 3+} and Eu{sup 3+} ions, respectively. The color coordinate can be tuned by changing the ratio between blue, green and red band by changing the concentration of lanthanides. - Graphical abstract: Strong blue emission from undoped BaZrO{sub 3} phosphor and white light emission by doping with Tb{sup 3+} (green) and Eu{sup 3+} (red) after 266 nm excitation. Highlights: Black-Right-Pointing-Pointer Blue emission from BaZrO{sub 3} phosphor. Black-Right-Pointing-Pointer Blue emission enhanced with Tm{sup 3+}. Black-Right-Pointing-Pointer White light from BaZrO{sup 3+} phosphor.

Structure dependent luminescence characterization of green-yellow emitting Sr{sub 2}SiO{sub 4}:Eu{sup 2+} phosphors for near UV LEDs

Energy Technology Data Exchange (ETDEWEB)

Han, J.K. [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); Hannah, M.E.; Piquette, A. [Central Research, OSRAM SYLVANIA, 71 Cherry Hill Drive Beverly, MA 01915 (United States); Hirata, G.A. [Centro de Nanociencias y Nanotecnolgia, Universidad Nacional Autonoma de Mexico, Km. 107 Carretera Tijuana-Ensenada Apdo, Ensenada, MX CP 22860 (Mexico); Talbot, J.B. [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); Mishra, K.C. [Central Research, OSRAM SYLVANIA, 71 Cherry Hill Drive Beverly, MA 01915 (United States); McKittrick, J., E-mail: jmckittrick@ucsd.edu [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States)

2012-01-15

This paper reports on the luminescence properties of mixtures of {alpha}- and {beta}-(Sr{sub 0.97}Eu{sub 0.03}){sub 2}SiO{sub 4} phosphors. These phosphors were prepared by 3 different synthesis techniques: a modified sol-gel/Pechini method, a co-precipitation method and a combustion method. The structural and optical properties of these phosphors were compared to those of solid state synthesized powders. The emission spectra consist of a weak broad blue band centered near 460 nm and a strong broad green-yellow band centered between 543 and 573 nm depending on the crystal structure. The green-yellow emission peak blue-shifts as the amount of {beta} phase increases and the photoluminescence emission intensity and quantum efficiency of the mixed phase powders is greater than those of predominant {alpha}-phase powders when excited between 370 and 410 nm. Thus, (Sr{sub 1-x}Eu{sub x}){sub 2}SiO{sub 4} with larger proportion of the {beta} phase are more promising candidates than single {alpha}-phase powders for use as a green-yellow emitting phosphor for near UV LED applications. Finally the phosphors prepared by the sol-gel/Pechini method, which have larger amount of {beta} phase, have a higher emission intensity and quantum efficiency than those prepared by co-precipitation or combustion synthesis. - Highlights: > Mixtures of {alpha}- and {beta}-Sr{sub 2}SiO{sub 4}:Eu{sup 2+} phosphors were prepared by 3 different synthesis methods. > Emission peak blue-shifts as the amount of {beta} phase increases. > Emission intensity and QE of the {alpha}+{beta} powders are greater than those of single {alpha} phase. > Phosphors prepared by sol-gel/Pechini have the highest emission intensity and QE.

Synthesis and photoluminescence properties of Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red phosphors for white LED applications

Energy Technology Data Exchange (ETDEWEB)

Annadurai, G.; Kennedy, S. Masilla Moses, E-mail: kennedysmm@ssn.edu.in

2016-01-15

Novel pellyite type Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red emitting phosphors with different Eu{sup 3+} contents were synthesized by the solid state reaction method. The crystal structure, photoluminescence properties and concentration quenching of Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} phosphors were investigated. Powder X-ray diffraction measurements confirmed the structure of the samples. The photoluminescence emission (PL) and excitation (PLE) spectra were measured. The results showed that the dominant hypersensitive red emission peak of the phosphors Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} was located at 613 nm attributed to the Eu{sup 3+} transition ({sup 5}D{sub 0}→{sup 7}F{sub 2}) which could be effectively excited by 395 nm (near-UV). The latter band matched well with the emission from the near-UV LED chips. The intensity ratio of {sup 5}D{sub 0}→{sup 7}F{sub 2} to {sup 5}D{sub 0}→{sup 7}F{sub 1} transition showed slight variation with Eu{sup 3+} concentrations. The Eu{sup 3+} emission intensity was maximum for 9 mol%. The luminescence quantum efficiency was determined and also the decay profiles were obtained and analyzed. In addition, the Commission International del'Eclairage (CIE) chromaticity coordinates of Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:0.09Eu{sup 3+} phosphor were calculated to be 0.637 and 0.362. The experimental results demonstrated that the Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red emitting phosphor is a potential candidate for white light emitting diodes (WLEDs) pumped by near-UV chip. - Highlights: • A novel Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17}:Eu{sup 3+} red phosphor was synthesized. • The samples yielded a dominant PL emission of Eu{sup 3+} at 613 nm. • Eu{sup 3+} concentration was optimized to be 9 mol% in Ba{sub 2}CaZn{sub 2}Si{sub 6}O{sub 17.} • CIE chromaticity coordinates were estimated from the emission spectrum.

Mechanical properties of hexaferite based magnet composite of SrFe12019 and BaFe12O19 with natural rubber bonding agent

International Nuclear Information System (INIS)

Waluyo, T.; Herman, Y.A.; Sudirman; Ridwan

2000-01-01

Research on mechanical properties at magnet composite of SrFe 12 0 19 (SrM) and BaFe 12 O 19 (BaM)magnet powder with natural rubber bonding agent have been done. The natural rubber used was rubber made of latex without vulcanization, The SrM powder having average particle size of 1.6 μm and flat shaped. and the BaM powder having particle size of 1.2 μm and nodular shaped. The production of composite carried out in Labo Plastomill at 100 o C and mixer speed of 30 rpm for 7 minutes. The result obtained from Labo Plastomill then made into sheets. Mechanical properties of the composite tested were strain, elongation break and hardness, The results showed that the highest strain of the SrM composite obtained at composition of 70% vol of powder that is 2,22 MPa, and 3,84 MPa for BaM composite at 50% vol. of powder The elongation break of SrM composite decreased by increasing of powder volume fraction, that is 90% at the composition or 70% vol. of powder, and 370% for BaM composite at 50% vol. fraction of powder. The highest hardness for SrM composite obtained at composition of of 70% vol. of powder, that is 95 SHA. and for the BaM composite at 50% vol. of powder. that is 52 SHA

Structural studies of the rhombohedral and orthorhombic monouranates: CaUO{sub 4}, α-SrUO{sub 4}, β-SrUO{sub 4} and BaUO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Murphy, Gabriel [School of Chemistry, The University of Sydney, Sydney, NSW 2006 (Australia); Kennedy, Brendan J., E-mail: kennedyb@chem.usyd.edu.au [School of Chemistry, The University of Sydney, Sydney, NSW 2006 (Australia); Johannessen, Bernt; Kimpton, Justin A. [Australian Synchrotron, 800 Blackburn Road, Clayton, Victoria 3168 (Australia); Avdeev, Maxim; Griffith, Christopher S.; Thorogood, Gordon J.; Zhang, Zhaoming [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW 2234 (Australia)

2016-05-15

The structures of some AUO{sub 4} (A=Ca, Sr, or Ba) oxides have been determined using a combination of neutron and synchrotron X-ray diffraction, supported by X-ray absorption spectroscopic measurements at the U L{sub 3}-edge. The smaller Ca cation favours a rhombohedral AUO{sub 4} structure with 8-coordinate UO{sub 8} moieties whilst an orthorhombic structure based on UO{sub 6} groups is found for BaUO{sub 4}. Both the rhombohedral and orthorhombic structures can be stabilised for SrUO{sub 4}. The structural studies suggest that the bonding requirements of the A site cation play a significant role in determining which structure is favoured. In the rhombohedral structure, Bond Valence Sums demonstrate the A site is invariably overbonded, which, in the case of rhombohedral α-SrUO{sub 4}, is compensated for by the formation of vacancies in the oxygen sub-lattice. The uranium cation, with its flexible oxidation state, is able to accommodate this by inducing vacancies along its equatorial coordination site as demonstrated by neutron powder diffraction. - Graphical abstract: Diffraction studies of AUO{sub 4} (A = Ca, Sr, or Ba) oxides reveal the importance of the bonding requirements of the A site cation in determining whether the structure is rhombohedral or orthorhombic. - Highlights: • Structures of AUO{sub 4} ( A = Ca Sr, Ba) refined against X-ray and Neutron diffraction. • The alkali cations size has a dramatic effect on the crystal structure. • Smaller cations favouring a rhombohedral structure. • Oxygen vacancies to stabilise the rhombohedral structure in SrUO{sub 4}.

Enhancement of photoluminescence properties and modification of crystal structures of Si3N4 doping Li2Sr0.995SiO4:0.005Eu2+ phosphors

International Nuclear Information System (INIS)

Song, Kaixin; Zhang, Fangfang; Chen, Daqin; Wu, Song; Zheng, Peng; Huang, Qingming; Jiang, Jun; Xu, Junming; Qin, Huibin

2015-01-01

Highlights: • Si 3 N 4 modified Li 2 Sr 0.995 SiO 4 :0.005Eu 2+ phosphors were prepared. • The luminescence intensity of Li 2 Sr 0.995 SiO 4 :Eu 2+ was enhanced by doping Si 3 N 4 . • The fluorescence decay times and thermal stability were enhanced by doping Si 3 N 4 . - Abstract: Si 3 N 4 modified Li 2 Sr 0.995 SiO 4 :0.005Eu 2+ (Li 2 Sr 0.995 SiO 4−3x/2 N x :0.005Eu 2+ ) phosphors were synthesized with the conventional solid-state reaction in the reduced atmosphere. The crystal structure and vibrational modes were analyzed by X-ray diffraction, Raman scattering spectroscopy and Rietveld crystal structure refinement. Photoluminescence (PL) and photoluminescence excitation (PLE) spectra showed that Li 2 Sr 0.995 SiO 4−3x/2 N x :0.005Eu 2+ powder exhibited a broad yellow emission band centered at 560 nm under the excitation of 460 nm visible light, due to the 4f 6 5d 1 → 4f 7 transition of Eu 2+ . The partial nitridation of Li 2 Sr 0.995 SiO 4−3x/2 N x :0.005Eu 2+ (x = 0.01) phosphors led to a large enhancement in the luminescence intensity, as much as 190%. At the same time, the fluorescence decay behavior curves further showed that the photoluminescence efficiencies of Li 2 Sr 0.995 SiO 4−3x/2 N x :0.005Eu 2+ phosphors were enhanced by addition of Si 3 N 4 . The temperature quenching characteristics confirmed that the oxynitride based Li 2 Sr 0.995 SiO 4−3x/2 N x :0.005Eu 2+ showed slightly higher stability. It is implied that Li 2 Sr 0.995 SiO 4−3x/2 N x :0.005Eu 2+ phosphors had a possible potential application on white LEDs to match blue light chips

Effect of divalent (Sr, Ba) doping on the structural and magnetic properties of BiFeO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Rangi, Manisha, E-mail: mrangi100@gmail.com; Sanghi, Sujata; Agarwal, Ashish; Jangra, Sandhaya; Singh, Ompal [Department of Applied Physics, Guru Jambheshwar University of Science and Technology, Hisar, Haryana- 125001 (India)

2015-06-24

The effect of divalent substitution on the crystal structure and magnetic properties of BiFeO{sub 3} has been investigated using X-ray diffraction and magnetic measurements technique. Single phase Bi{sub 0.8}A{sub 0.2}FeO{sub 3} (A= Sr, Ba) multiferroics have been synthesized by solid state reaction method. Rietveld analysis of the XRD patterns revealed that the prepared ceramics exhibit rhombohedral structure with space group R3c. M–H hysteresis loops were recorded at 5K revealed that Sr and Ba substitution transformed antiferromagnetic BiFeO3 into weak ferromagnetic. The enhanced magnetization with Sr and Ba addition is confirmed by the MT curve recorded at 1T. It is closely related to intrinsic structural distortion and modification of the antiparallel spin structure.

A novel single-phase white phosphor NaBaBO{sub 3}:Dy{sup 3+},K{sup +} for near-UV white light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Zheng, Jianghui; Cheng, Qijin; Wu, Jieyang; Cui, Xin; Chen, Rong; Chen, Wenzhi [School of Energy Research, Xiamen University, Xiamen 361005 (China); Chen, Chao, E-mail: cchen@xmu.edu.cn [School of Energy Research, Xiamen University, Xiamen 361005 (China); School of Physics and Mechanical & Electrical Engineering, Xiamen University, Xiamen, 361005 (China)

2016-01-15

Highlights: • A white phosphor NaBaBO{sub 3}:Dy{sup 3+},K{sup +} with CIE coordinate (0.301, 0.308) was synthesized. • The optimum doping concentration of Dy{sup 3+} ions was found. • The effect and mechanism of K{sup +} ion as a charge compensator were discussed. • Temperature-dependent PL property of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} was studied. • PL decay and quantum efficiency behaviors of the samples were investigated. - Abstract: A novel Dy{sup 3+}-doped NaBaBO{sub 3} white-emitting phosphor has been prepared by high temperature solid-state reaction method. The phase structure and luminescence properties of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} samples were investigated. Photoluminescence results show that the as-prepared samples could be effectively excited by near-ultraviolet (NUV) light and generate white light emission due to the {sup 4}F{sub 9/2} → {sup 6}H{sub 15/2} (blue) transition and {sup 4}F{sub 9/2} → {sup 6}H{sub 13/2} (yellow) transition of Dy{sup 3+} ions, respectively. The optimum doping concentration of Dy{sup 3+} ions in the NaBaBO{sub 3} host was determined to be 5.0 mol% and the CIE chromaticity of the sample was determined to be (0.301, 0.308). Moreover, the mechanism of K{sup +} ion as a charge compensator on the improvement of photoluminescence property and the effect of temperature on the photoluminescence property of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} were investigated. Furthermore, photoluminescence decay and quantum efficiency behaviors of NaBaBO{sub 3}:Dy{sup 3+},K{sup +} were also studied. The present work demonstrates that the NaBaBO{sub 3}:Dy{sup 3+},K{sup +} phosphor is a potential candidate for NUV white light emitting diodes.

Trigermanides AEGe{sub 3} (AE = Ca, Sr, Ba). Chemical bonding and superconductivity

Energy Technology Data Exchange (ETDEWEB)

Castillo, Rodrigo; Schnelle, Walter; Baranov, Alexey I.; Burkhardt, Ulrich; Bobnar, Matej; Cardoso-Gil, Raul; Schwarz, Ulrich; Grin, Yuri [Max-Planck-Institut fuer Chemische Physik Fester Stoffe, Dresden (Germany)

2016-08-01

The crystal structures of the trigermanides AEGe{sub 3}(tI32) (AE = Ca, Sr, Ba; space group I4/mmm, for SrGe{sub 3}: a = 7.7873(1), c = 12.0622(3) Aa) comprise Ge{sub 2} dumbbells forming layered Ge substructures which enclose embedded AE atoms. The chemical bonding analysis by application of the electron localizability approach reveals a substantial charge transfer from the AE atoms to the germanium substructure. The bonding within the dumbbells is of the covalent two-center type. A detailed analysis of SrGe{sub 3} reveals that the interaction on the bond-opposite side of the Ge{sub 2} groups is not lone pair-like - as it would be expected from the Zintl-like interpretation of the crystal structure with anionic Ge layers separated by alkaline-earth cations - but multi-center strongly polar between the Ge{sub 2} dumbbells and the adjacent metal atoms. Similar atomic interactions are present in CaGe{sub 3} and BaGe{sub 3}. The variation of the alkaline-earth metal has a merely insignificant influence on the superconducting transition temperatures in the s,p-electron compounds AEGe{sub 3}.

Glass formation and physicochemical properties of glasses of Ba(PO3)2-LiRAlF6 (R=Mg, Ca, Sr, Ba) system

International Nuclear Information System (INIS)

Khalilev, V.D.; Chkhenkeli, G.D.; Vakhrameev, V.I.

1987-01-01

Glass formation regions, crystallizability, optical constants, thermal linear expansion coefficient and IR absorption spectra of glass are studied in Ba(PO) 3 ) 2 - LiRAlF 6 system where R=Mg, Ca, Sr, Ba. The carried out investigation confirms participation of introduced fluorides (as modified cryolites) in structural transformations manifested in increase of glass formation regions and nonlinear variations of properties

Low temperature rf sputtering deposition of (Ba, Sr) TiO3 thin film with crystallization enhancement by rf power supplied to the substrate

International Nuclear Information System (INIS)

Yoshimaru, Masaki; Takehiro, Shinobu; Abe, Kazuhide; Onoda, Hiroshi

2005-01-01

The (Ba, Sr) TiO 3 thin film deposited by radio frequency (rf) sputtering requires a high deposition temperature near 500 deg. C to realize a high relative dielectric constant over of 300. For example, the film deposited at 330 deg. C contains an amorphous phase and shows a low relative dielectric constant of less than 100. We found that rf power supplied not only to the (Ba, Sr) TiO 3 sputtering target, but also to the substrate during the initial step of film deposition, enhanced the crystallization of the (Ba, Sr) TiO 3 film drastically and realized a high dielectric constant of the film even at low deposition temperatures near 300 deg. C. The 50-nm-thick film with only a 10 nm initial layer deposited with the substrate rf biasing is crystallized completely and shows a high relative dielectric constant of 380 at the deposition temperature of 330 deg. C. The (Ba, Sr) TiO 3 film deposited at higher temperatures (upwards of 400 deg. C) shows preferred orientation, while the film deposited at 330 deg. C with the 10 nm initial layer shows a preferred orientation on a -oriented ruthenium electrode. The unit cell of (Ba, Sr) TiO 3 (111) plane is similar to that of ruthenium (001) plane. We conclude that the rf power supplied to the substrate causes ion bombardments on the (Ba, Sr) TiO 3 film surface, which assists the quasiepitaxial growth of (Ba, Sr) TiO 3 film on the ruthenium electrode at low temperatures of less than 400 deg. C

Low temperature rf sputtering deposition of (Ba, Sr) TiO3 thin film with crystallization enhancement by rf power supplied to the substrate

Science.gov (United States)

Yoshimaru, Masaki; Takehiro, Shinobu; Abe, Kazuhide; Onoda, Hiroshi

2005-05-01

The (Ba, Sr) TiO3 thin film deposited by radio frequency (rf) sputtering requires a high deposition temperature near 500 °C to realize a high relative dielectric constant over of 300. For example, the film deposited at 330 °C contains an amorphous phase and shows a low relative dielectric constant of less than 100. We found that rf power supplied not only to the (Ba, Sr) TiO3 sputtering target, but also to the substrate during the initial step of film deposition, enhanced the crystallization of the (Ba, Sr) TiO3 film drastically and realized a high dielectric constant of the film even at low deposition temperatures near 300 °C. The 50-nm-thick film with only a 10 nm initial layer deposited with the substrate rf biasing is crystallized completely and shows a high relative dielectric constant of 380 at the deposition temperature of 330 °C. The (Ba, Sr) TiO3 film deposited at higher temperatures (upwards of 400 °C) shows preferred orientation, while the film deposited at 330 °C with the 10 nm initial layer shows a preferred orientation on a -oriented ruthenium electrode. The unit cell of (Ba, Sr) TiO3 (111) plane is similar to that of ruthenium (001) plane. We conclude that the rf power supplied to the substrate causes ion bombardments on the (Ba, Sr) TiO3 film surface, which assists the quasiepitaxial growth of (Ba, Sr) TiO3 film on the ruthenium electrode at low temperatures of less than 400 °C.

Color tunable emission in Ce3+ and Tb3+ co-doped Ba2Ln(BO3)2Cl (Ln=Gd and Y) phosphors for white light-emitting diodes.

Science.gov (United States)

Zhang, Niumiao; Guo, Chongfeng; Jing, Heng; Jeong, Jung Hyun

2013-12-01

Ce(3+) and Tb(3+) co-doped Ba2Ln(BO3)2Cl (Ln=Y and Gd) green emitting phosphors were prepared by solid state reaction in reductive atmosphere. The emission and excitation spectra as well as luminescence decays were investigated, showing the occurrence of efficient energy transfer from Ce(3+) to Tb(3+) in this system. The phosphors exhibit both a blue emission from Ce(3+) and a green emission from Tb(3+) under near ultraviolet light excitation with 325-375 nm wavelength. Emission colors of phosphors could be tuned from deep blue through cyan to green by adjusting the Tb(3+) concentrations. The energy transfer efficiency and emission intensity of Ba2Y(BO3)2Cl:Ce(3+), Tb(3+) precede those of Ba2Gd(BO3)2Cl:Ce(3+), Tb(3+), and the sample Ba2Y(BO3)2Cl:0.03Ce(3+), 0.10Tb(3+) is the best candidate for n-UV LEDs. Copyright © 2013 Elsevier B.V. All rights reserved.

Luminescence of (Ca,Sr)3(VO4)2: Pr3+, Eu3+ phosphor for use in CuPc-based solar cells and white light-emitting diodes

International Nuclear Information System (INIS)

Lin, Han-Yu; Chang, Wei-Fu; Chu, Sheng-Yuan

2013-01-01

The purpose of this study is to enhance the red emission intensity and expand the blue excitation band of a (Ca,Sr) 2.82 (VO 4 ) 2 :0.12Eu 3+ phosphor for use in copper phthalocyanine (CuPc)-based solar cells and white light-emitting diodes. It was found that substitution of 3% Sr 2+ replacing Ca 2+ enhanced red emission intensity of Ca 2.82 (VO 4 ) 2 :0.12Eu 3+ by 14% under 465-nm by excitation. The Pr 3+ co-doping effect was realized when blue excitation intensity of (Ca 0.97 Sr 0.03 ) 2.82 (VO 4 ) 2 :0.12Eu 3+ , located in the weakest absorption of CuPc, was improved by 126% with the addition of 0.6 mol% Pr 3+ . The absorption spectrum of CuPc/optimized (Ca 0.9668 Sr 0.03 ) 2.82 (VO 4 ) 2 :0.006Pr 3+ , 0.12Eu 3+ mixtures provided evidence that the (Ca 0.9668 Sr 0.03 ) 2.82 (VO 4 ) 2 :0.006Pr 3+ , 0.12Eu 3+ phosphor could increase the efficiency of incident photons on CuPc-based solar cells. Moreover, the good temperature stability of emission intensity and chromaticity of (Ca 0.9668 Sr 0.03 ) 2.82 (VO 4 ) 2 :0.006Pr 3+ , 0.12Eu 3+ indicated a potential for this phosphor to be applied on the white light-emitting diodes. - Highlights: ► Substitution of 3% Sr 2+ replacing Ca 2+ enhanced red emission intensity of Ca 2.82 (VO 4 ) 2 :0.12Eu 3+ by 14% under 465 nm by excitation. ► Addition of 0.6 mol% Pr 3+ enhanced blue excitation intensity of (Ca 0.97 Sr 0.03 ) 2.82 (VO 4 ) 2 :0.12Eu 3+ , located in the weakest absorption of CuPc, by 126%. ► According to absorption measurements of CuPc/optimized (Ca 0.9668 Sr 0.03 ) 2.82 (VO 4 ) 2 :0.006Pr 3+ , 0.12Eu 3+ mixtures for the first time, the feasibility of our phosphor to assist CuPc in converting blue-wavelength photons was proved. ► High temperature stability of emission intensity and chromaticity of (Ca 0.9668 Sr 0.03 ) 2.82 (VO 4 ) 2 :0.006Pr 3+ , 0.12Eu 3+ indicated our phosphor is acceptable for WLED applications.

Long lasting yellow phosphorescence and photostimulated luminescence in Sr3SiO5 : Eu2+ and Sr3SiO5 : Eu2+, Dy3+ phosphors

International Nuclear Information System (INIS)

Sun Xiaoyuan; Zhang Jiahua; Zhang Xia; Luo Yongshi; Wang Xiaojun

2008-01-01

We report the observation of long lasting yellow phosphorescence and photostimulated luminescence (PSL) in Sr 3 SiO 5 : Eu 2+ and Sr 3 SiO 5 : Eu 2+ , Dy 3+ phosphors. The decay patterns of phosphorescence and thermoluminescence curves demonstrate that introduction of Dy 3+ into Sr 3 SiO 5 : Eu 2+ can generate a large number of shallow traps and deep traps. The generated deep traps prolong the phosphorescence up to 6 h after UV irradiation. The PSL is studied under 808 nm excitation. Slow rising and falling edges of the emission in Sr 3 SiO 5 : Eu 2+ , Dy 3+ are observed, showing a retrapping process by the generated shallow traps due to co-doping Dy 3+ .

Red-emitting SrIn{sub 2}O{sub 4} : Eu{sup 3+} phosphor powders for applications in solid state white lamps

Energy Technology Data Exchange (ETDEWEB)

Rodriguez-Garcia, C E [Physics of Materials Graduate Program, CICESE-UNAM, Km 107 Carretera Tijuana-Ensenada, Ensenada, B. C., 22860 (Mexico); Perea-Lopez, N; Hirata, G A [Center for Nanoscience and Nanotechnology-UNAM, Km 107 Carretera Tijuana-Ensenada, Ensenada, B. C., 22860 (Mexico); Baars, S P den [Solid State Lighting and Energy Center, University of California at Santa Barbara, Santa Barbara, CA 93106 (United States)], E-mail: ghirata@engineering.ucsb.edu

2008-05-07

Red-emitting phosphor powders of SrIn{sub 2}O{sub 4} activated with Eu{sup 3+} ions were fabricated by high pressure assisted combustion synthesis. X-ray diffraction analysis of these oxide phosphors revealed the formation of single-phase orthorhombic SrIn{sub 2}O{sub 4} for concentrations up to 4 at% Eu. A detailed photoluminescence (PL) and cathodoluminescence study showed bright red emission originated within the {sup 5} D{sub 0} {yields} {sup 7}F{sub J} intra-shell transitions of Eu{sup 3+}. Furthermore, PL excitation spectroscopy revealed that an efficient energy transfer from the SrIn{sub 2}O{sub 4} host lattice onto the Eu ions is accomplished in addition to the excitation band peaked at 396 nm that directly excites the Eu ions, making this material an excellent candidate for applications in solid state white lamps. (fast track communication)

Electrical behavior of Ca, Sr, Ba, and Eu at very high pressures and low temperatures

International Nuclear Information System (INIS)

Bundy, F.P.; Dunn, K.J.

1981-01-01

Compression of Ca and Sr initially causes an increase in resistivity, probably because of uncrossing of conduction and valence bands. Then at about 180 kbar for Ca and about 35 kbar for Sr the resistivity drops quite abruptly, following which the resistivity again increases with additional pressure, similar to the behavior of Ba starting at room pressure. The high pressure forms of Ba have already been reported to be superconducting, and the experiments confirm this. Superconductivity appears in Sr at about 350 kbar and develops strongly at higher pressures. In the 440 kbar experiment on Ca a resistance drop started at the lower threshold of the temperature capability, 2.1K, suggesting that Ca, too, becomes superconducting at sufficiently high pressures. The high pressure form of Eu above 125 kbar was tested for superconductivity down to 2.2K with negative results. (Auth.)

A potential green emitting citrate gel synthesized NaSrBO3:Tb3+ phosphor for display application

Science.gov (United States)

Bedyal, A. K.; Kumar, Vinay; Swart, H. C.

2018-04-01

A potential green emitting NaSrBO3:Tb3+ (1-9 mol%) phosphor was synthesized by a citrate gel combustion method. X-ray diffraction patterns confirmed the monoclinic phase of the phosphor. The phosphor emitted intense green emission under near-UV and electron excitation due to the characteristic transitions 5D4→7F6(488 nm),5D4→7F5(544 nm),5D4→7F4(586 nm) and 5D4→7F3(622 nm) of Tb3+ ions. The optimal molar concentration of Tb3+ ions was found to be 6 mol%, after that concentration quenching occurred. The dipole-dipole interaction was found to be accountable for energy transfer between the Tb3+ ions. X-ray photoelectron spectroscopy was carried out to analyze the chemical states of the elements and suggest that terbium was mostly presented in the (+3) valance state in the phosphor. The approximated Commission Internationale de l‧Eclairage coordinates for the PL (0.31, 0.61) and CL (0.33, 0.57) were found to be very close to the well-known green emitting phosphor. The obtained results suggest that the studied phosphor could be an ultimate choice for green emission in display applications.

High Q ceramics in the ACe2(MoO4)4 (A = Ba, Sr and Ca) system for LTCC applications

International Nuclear Information System (INIS)

Surjith, A.; Ratheesh, R.

2013-01-01

Highlights: ► Solid state synthesis of phase pure ACe 2 (MoO 4 ) 4 (A = Ba, Sr and Ca) ceramics. ► Structural and microstructural evaluation of the synthesized ceramic materials. ► Microwave dielectric property studies of ACe 2 (MoO 4 ) 4 (A = Ba, Sr and Ca) ceramics. ► Structure-property correlation through Laser Raman studies. - Abstract: Novel low temperature sinterable high Q ceramic systems ACe 2 (MoO 4 ) 4 (A = Ba, Sr and Ca) have been prepared through solid state ceramic method. The effect of ionic radii of alkaline earth cations on the structure, microstructure and microwave dielectric properties of these ceramics were studied using powder X-ray diffraction, Laser Raman spectroscopy, scanning electron microscopy and Vector Network Analyzer. A structural change from monoclinic to tetragonal structure was observed while substituting Sr 2+ and Ca 2+ cations in place of Ba 2+ . The Sr and Ca analogues possess better microwave dielectric properties compared to BaCe 2 (MoO 4 ) 4 . All the ceramics were well sintered below 840 °C with dielectric constant in the range 10.2–12.3 together with good quality factor. The SrCe 2 (MoO 4 ) 4 ceramic exhibits an unloaded quality factor of 6762 at 8.080662 GHz with a temperature coefficient of resonant frequency of −46 ppm/°C while the CaCe 2 (MoO 4 ) 4 ceramic shows an unloaded quality factor of 7549 at 6.928868 GHz and a temperature coefficient of resonant frequency of −44 ppm/°C.

Single-phased white-light-emitting Sr3NaLa(PO4)3F: Eu2+,Mn2+ phosphor via energy transfer

International Nuclear Information System (INIS)

Shanshan, Hu; Wanjun, Tang

2014-01-01

Single-phased white-light-emitting Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ phosphor is synthesized via the combustion-assisted synthesis technique. Upon excitation of 344 nm ultraviolet (UV) light, two intense broad bands have clearly been obtained due to the allowed 5d–4f transition of Eu 2+ and the forbidden 4 T 1 − 6 A 1 transition of Mn 2+ , respectively. As a result of fine-tuning of the emission composition of the Eu 2+ and Mn 2+ ions, white-light emission can be realized by combining the emission of Eu 2+ and Mn 2+ in a single host lattice under UV light excitation. The obtained phosphor exhibits a strong excitation band between 250 and 420 nm, matching well with the dominant emission band of a UV light-emitting-diode (LED) chip, which could be a promising candidate for UV-converting white-light-emitting diodes (LEDs). -- Highlights: • Single-phased Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ phosphors are synthesized. • Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ shows a blue emission band and a yellow emission band. • White-emitting can be obtained by tuning the compositions of the Eu 2+ and Mn 2+

Ferromagnetism and half metallicity induced by oxygen vacancies in the double perovskite BaSrNiWO{sub 6}: DFT study

Energy Technology Data Exchange (ETDEWEB)

Aharbil, Y. [Laboratoire de Chimie Physique des Matériaux LCPM, Faculté des Sciences Ben M' Sik, Casablanca (Morocco); Labrim, H. [Unité Science de la Matière/DERS/Centre National de l’Energie, des Sciences et des Techniques Nucléaires (CNESTEN), Rabat (Morocco); Benmokhtar, S.; Haddouch, M. Ait [Laboratoire de Chimie Physique des Matériaux LCPM, Faculté des Sciences Ben M' Sik, Casablanca (Morocco); Bahmad, L., E-mail: bahmad@fsr.ac.ma [Mohammed V University in Rabat, Laboratoire de Magnétisme et Physique des Hautes Energies L.M.P.H.E. URAC-12, B.P. 1014, Rabat (Morocco); Belhaj, A. [LIRST, Département de Physique, Faculté Poly-disciplinaire, Université Sultan Moulay Slimane, Béni Mellal (Morocco); Ez-Zahraouy, H.; Benyoussef, A. [Mohammed V University in Rabat, Laboratoire de Magnétisme et Physique des Hautes Energies L.M.P.H.E. URAC-12, B.P. 1014, Rabat (Morocco)

2016-11-01

Using the spin polarized density functional theory (DFT) and exploring the Plane-Wave Self-Consistent Field (PWscf) code implemented in Quantum-ESPRESSO package, we investigate the effect of the Oxygen vacancies (V{sub O}) and the Oxygen interstitial (O{sub i}) on the double perovskite BaSrNiWO{sub 6}. This deals with the magnetic ordering and the electronic structure in such a pure sample exhibiting the insulating anti-ferromagnetic (AFM) state. This study shows that the presence of oxygen deficient defects converts the insulating to half metal with ferromagnetic or anti-ferromagnetic states. The magnetic ordering in BaSrNiWO{sub 6−δ} depends on the position of the Oxygen vacancy in the unit cell. However, it has been shown that the Oxygen interstitial preserves the anti-ferromagnetic propriety. We have computed the formation energies of different positions of the Oxygen vacancy (V{sub O}) and the Oxygen interstitial (O{sub i}) in the BaSrNiWO{sub 6} compound. We showed that the formation of V{sub O} is easier and vice versa for the O{sub i} formation. The obtained results reveal(V{sub O}) and the Oxygen interstitial (O{sub i}) that the anti-ferromagnetic can be converted to ferromagnetic in the double perovskite BaSrNiWO{sub 6} induced by Oxygen vacancies V{sub O}. - Highlights: • We have studied the ferromagnetism and Half Metallicity in Double Perovskite BaSrNiWO{sub 6}. • We have applied the Ab-inito calculations using the DFT approach. • We showed the effects induced by Oxygen Vacancies and Oxygen interstitial. • We found that the magnetic ordering in BaSrNiWO{sub 6−δ} depends on the position of the Oxygen vacancy in the unit cell.

Impedance spectroscopy and structural properties of the perovskite-like Sn(Ba,Sr)O{sub 3} stagnate

Energy Technology Data Exchange (ETDEWEB)

Cuervo Farfan, J. [Grupo de Fisica de Nuevos Materiales, Departamento de Fisica, Universidad Nacional de Colombia, AA 5997, Bogota DC (Colombia); Ciencias Basicas, Universidad Manuela Beltran, Bogota DC (Colombia); Olaya, J.J. [Departamento de Ingenieria Mecanica y Mecatronica, Universidad Nacional de Colombia, Bogota DC (Colombia); Vera Lopez, E. [Grupo de Superficies, Electroquimica y Corrosion, Universidad Pedagogica y Tecnologica de Colombia, Tunja (Colombia); Landinez Tellez, D.A. [Grupo de Fisica de Nuevos Materiales, Departamento de Fisica, Universidad Nacional de Colombia, AA 5997, Bogota DC (Colombia); Roa-Rojas, J., E-mail: jroar@unal.edu.co [Grupo de Fisica de Nuevos Materiales, Departamento de Fisica, Universidad Nacional de Colombia, AA 5997, Bogota DC (Colombia)

2012-08-15

An exhaustive study of structural, electrical and transport properties on the perovskite stagnate Sn(Ba,Sr)O{sub 3} was performed. Samples of SnBa{sub 1-x}Sr{sub x}O{sub 3} with 0{<=}x{<=}1.00 were prepared by the solid state reaction method. The crystallographic structure was studied by X-ray diffraction experiments and Rietveld refinement using the GSAS code. Results reveal the material synthesized in a cubic structure (space group Pm3-bar m, no. 221) for 0{<=}x{<=}0.50 and in an orthorhombic (space group Pnma, no. 62) for x>0.50. The approximate grain size was found from experiments' Scanning Electron Microscopy. The electric response was studied by the Impedance Spectroscopy technique from 10.0 mHz up to 0,10 MHz. Electric polarization measurements for SnSrO{sub 3} and SnBaO{sub 3} were determined through curves of polarization as a function of applied electric field, which reveal the ferroelectric character of the material. From the saturation polarization the dielectric constants of materials were calculated.

The transfer of 45Ca, 85Sr and 140Ba from mother to newborn in rats

International Nuclear Information System (INIS)

Taylor, D.M.; Bligh, P.H.

1992-01-01

Comparative studies of the transfer of 45 Ca, 85 Sr and 140 Ba from mother to offspring were made in August rats following intravenous injection of the radionuclides either during gestation or 40 to 90 days prior to mating. Immediately following parturition, and before suckling could begin, the newborn rats were removed from the dam and killed. For each radionuclide the percentage of the initial maternal activity transferred to individual offspring decreased exponentially with time between injection and parturition with a mean half-time of 3.1 ± 0.7 (SD) days. Transfer ratios measured in rats injected either during or prior to gestation were similar and could be described by the rounded values Ca: Sr: Ba = 1.00: 0.4:0.2. Placental transfer ratios were not significantly different from those for gastrointestinal absorption of the three radionuclides, plus 226 Ra, in adult rats of the same strain. For humans transfer ratios from mother to baby of Ca: Sr: Ba: Ra = 1.0: 0.6: 0.4: 0.4 are suggested. (author)

Structures, phase transitions and microwave dielectric properties of the 6H perovskites Ba3BSb2O9, B=Mg, Ca, Sr, Ba

International Nuclear Information System (INIS)

Ling, Chris D.; Rowda, Budwy; Avdeev, Maxim; Pullar, Robert

2009-01-01

We present a complete temperature-composition phase diagram for Ba 3 BSb 2 O 9 , B=Mg, Ca, Sr, Ba, along with their electrical behavior as a function of B. These compounds have long been recognized as 6H-type perovskites, but (with the exception of B=Mg) their exact structures and properties were unknown due to their low symmetries, temperature-dependent phase transitions, and difficulties in synthesizing pure samples. The full range of possible space group symmetries is observed, from ideal hexagonal P6 3 /mmc to monoclinic C2/c to triclinic P1-bar. Direct second-order transitions between these phases are plausible according to group theory, and no evidence was seen for any further intermediate phases. The phase diagram with respect to temperature and the effective ionic radius of B is remarkably symmetrical for B=Mg, Ca, and Sr. For B=Ba, a first-order phase transition to a locally distorted phase allows a metastable hexagonal phase to persist to lower temperatures than expected before decomposing around 600 K. Electrical measurements revealed that dielectric permittivity corrected for porosity does not change significantly as a function of B and is in a good agreement with the values predicted by the Clausius-Mossotti equation. - Graphical abstract: Thermodynamic phase diagram for Ba 3 BSb 2 O 9 , B=Mg, Ca, and Sr, as a function of temperature T and effective ionic radius (IR) of the B 2+ cation

Composition Screening in Blue-Emitting Li4Sr1+xCa0.97-x(SiO4)2:Ce3+ Phosphors for High Quantum Efficiency and Thermally Stable Photoluminescence.

Science.gov (United States)

Zhang, Jingchen; Zhang, Jilin; Zhou, Wenli; Ji, Xiaoyu; Ma, Wentao; Qiu, Zhongxian; Yu, Liping; Li, Chengzhi; Xia, Zhiguo; Wang, Zhengliang; Lian, Shixun

2017-09-13

Photoluminescence quantum efficiency (QE) and thermal stability are important for phosphors used in phosphor-converted light-emitting diodes (pc-LEDs). Li 4 Sr 1+x Ca 0.97-x (SiO 4 ) 2 :0.03Ce 3+ (-0.7 ≤ x ≤ 1.0) phosphors were designed from the initial model of Li 4 SrCa(SiO 4 ) 2 :Ce 3+ , and their single-phased crystal structures were found to be located in the composition range of -0.4 ≤ x ≤ 0.7. Depending on the substitution of Sr 2+ for Ca 2+ ions, the absolute QE value of blue-emitting composition-optimized Li 4 Sr 1.4 Ca 0.57 (SiO 4 ) 2 :0.03Ce 3+ reaches ∼94%, and the emission intensity at 200 °C remains 95% of that at room temperature. Rietveld refinements and Raman spectral analyses suggest the increase of crystal rigidity, increase of force constant in CeO 6 , and decrease of vibrational frequency by increasing Sr 2+ content, which are responsible for the enhanced quantum efficiency and thermal stability. The present study points to a new strategy for future development of the pc-LEDs phosphors based on local structures correlation via composition screening.

Origin and Luminescence of Anomalous Red-Emitting Center in Rhombohedral Ba9Lu2Si6O24:Eu(2+) Blue Phosphor.

Science.gov (United States)

Liu, Yongfu; Zhang, Changhua; Cheng, Zhixuan; Zhou, Zhi; Jiang, Jun; Jiang, Haochuan

2016-09-06

We obtain a blue phosphor, Ba9Lu2Si6O24:Eu(2+) (BLS:Eu(2+)), which shows a strong emission peak at 460 nm and a weak tail from 460 to 750 nm. A 610 nm red emission is observed for the first time in this kind of rhombohedral structure material, which is much different from the same crystal structure of Ba9Sc2Si6O24:Eu(2+) and Ba9Y2Si6O24:Eu(2+). The luminescence properties and decays from 10 to 550 K are discussed. The new red emission arises from a trapped exciton state of Eu(2+) at the Ba site with a larger coordination number (12-fold). It exhibits abnormal luminescence properties with a broad bandwidth and a large Stokes shift. Under the 400 nm excitation, the external quantum efficiency of BLS:Eu(2+) is 45.4%, which is higher than the 35.7% for the commercial blue phosphor BAM:Eu(2+). If the thermal stability of BLS:Eu(2+) can be improved, it will show promising applications in efficient near-UV-based white LEDs.

Les Néandertaliens étaient-ils essentiellement carnivores ? Résultats préliminaires sur les teneurs en Sr et en Ba de la paléobiocénose mammalienne de Saint-CésaireWere Neandertalians essentially carnivores? Sr and Ba preliminary results of the mammalian palaeobiocoenosis of Saint-Césaire

Science.gov (United States)

Balter, Vincent; Person, Alain; Labourdette, Nathalie; Drucker, Dorothée; Renard, Maurice; Vandermeersch, Bernard

2001-01-01

Strontium-calcium (Sr/Ca) and barium-calcium (Ba/Ca) ratios are reduced constantly between diet and bioapatite in mammal organisms. This phenomenon leads to a reduction in the Sr/Ca and Ba/Ca ratios at higher trophic level in predator-prey mammalian communities, and is applied here to the reconstruction of a castelperronian food web, which includes a Neanderthal specimen. Adapted chemical pretreatment allows to isolate bioapatite from diagenetic compounds for analysis of Ca, Sr and Ba. Sr/Ca and Ba/Ca results of the fauna are consistent with trophic predictions. Initial results for the Neandertal suggest that he was mostly carnivorous. Distribution of Ba/Ca values of bones of herbivorous taxa reveals that ruminant animals can be distinguished from non-ruminants. The biosegregation model predicts that the diet of the Neandertal was composed by about 97 % in weight of meat with a weak contribution of vegetable or fish, and that the association of fish and plant is excluded in any proportion.

Formation pathways in the synthesis and properties of (Tl0.5Pb0.5)(Sr0.9Ba0.1)2Ca2Cu3Oz and (Tl0.5Pb0.5)(Sr0.8Ba0.2)2Ca2Cu3Oz-1223 superconductors

International Nuclear Information System (INIS)

Auinger, M; Gritzner, G; Bertrand, Ch; Galez, Ph; Soubeyroux, J-L

2007-01-01

The formation pathway of (Tl 0.5 Pb 0.5 )(Sr 0.9 Ba 0.1 ) 2 Ca 2 Cu 3 O z and (Tl 0.5 Pb 0.5 )(Sr 0.8 Ba 0.2 ) 2 Ca 2 Cu 3 O z was studied by neutron and x-ray diffraction. The following reaction pathway was proposed: thallium oxide and lead oxide react with Sr-rich (Sr 1-x Ca x )CuO 2 and Ca-rich (Ca x Sr 1-x )O to form Sr 4 Tl 2 O 7 and (Ca x Sr 1-x )PbO 3 , respectively. The thallate and the plumbate compounds then form the (Tl 0.5 Pb 0.5 )-1212 phase starting at a temperature of 600 deg. C. Finally, between 850 and 900 deg. C, the 1223 phase is formed from (Tl 0.5 Pb 0.5 )-1212 (Ca x Sr 1-x ) 2 CuO 3 and CuO. Parallel experiments to fabricate the (Tl, Pb)-1223 superconductor resulted in specimens with critical temperatures of 117.5 K and 116 K, respectively, and transition widths of 2 K. Differences between the pathways for the formation of Pb-doped, Sr-rich and Pb-free, Ba-rich Tl-1223 superconductors are discussed

On the application of CaF2:Eu and SrF2:Eu phosphors in LED based phototherapy lamp

Science.gov (United States)

Belsare, P. D.; Moharil, S. V.; Joshi, C. P.; Omanwar, S. K.

2013-06-01

In the last few years the interest of scientific community has been increased towards solid state lighting based on LEDs because of their superior advantages over the conventional fluorescent lamps. As the GaN based LEDs are easily available efforts of the researchers are now on making the new phosphors which are excitable in the near UV region (360-400nm) for solid state lighting. This paper reports the photoluminescence characteristics of CaF2:Eu and SrF2:Eu phosphor prepared by wet chemical method. The violet emission of these phosphors with near UV excitation can be useful in making a phototherapy lamp based on LEDs for treating various skin diseases like acne vulgaris and hyperbilirubinemia.

Luminescence enhancement of (Sr1-x Mx )2 SiO4 :Eu2+ phosphors with M (Ca2+ /Zn2+ ) partial substitution for white light-emitting diodes.

Science.gov (United States)

Wang, Yulong; Zhang, Wentao; Gao, Yang; Long, Jianping; Li, Junfeng

2017-02-01

Eu 2 + -doped Sr 2 SiO 4 phosphor with Ca 2 + /Zn 2 + substitution, (Sr 1-x M x ) 2 SiO 4 :Eu 2 + (M = Ca, Zn), was prepared using a high-temperature solid-state reaction method. The structure and luminescence properties of Ca 2 + /Zn 2 + partially substituted Sr 2 SiO 4 :Eu 2 + phosphors were investigated in detail. With Ca 2 + or Zn 2 + added to the silicate host, the crystal phase could be transformed between the α-form and the β-form of the Sr 2 SiO 4 structure. Under UV excitation at 367 nm, all samples exhibit a broad band emission from 420 to 680 nm due to the 4f 6 5d 1  → 4f 7 transition of Eu 2 + ions. The broad emission band consists of two peaks at 482 and 547 nm, which correspond to Eu 2 + ions occupying the ten-fold oxygen-coordinated Sr.(I) site and the nine-fold oxygen-coordinated Sr.(II) site, respectively. The luminescence properties, including the intensity and lifetime of Sr 2 SiO 4 :Eu 2 + phosphors, improved remarkably on Ca 2 + /Zn 2 + addition, and promote its application in white light-emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Ba{sub y}Sr{sub 1−y}TiO{sub 3} buffer layers for strain tuning of infinite-layer Sr{sub 1−x}La{sub x}CuO{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Sakuma, Keita, E-mail: sakuma.keita@d.mbox.nagoya-u.ac.jp; Ito, Masataka; He, Yilun; Hajiri, Tetsuya; Ueda, Kenji; Asano, Hidefumi

2016-08-01

We report on the precise tuning of lattice strain in an infinite-layer electron-doped high temperature superconductor Sr{sub 1−x}La{sub x}CuO{sub 2} (SLCO; a{sub SLCO} = 0.3949 nm for x = 0.1), which is a perovskite-related oxide, using perovskite BaTiO{sub 3}–SrTiO{sub 3} (BSTO; Ba{sub y}Sr{sub 1−y}TiO{sub 3}) buffer layers. The BSTO buffer layers formed on (001) (La{sub 0.18}Sr{sub 0.82})(Al{sub 0.59}Ta{sub 0.41})O{sub 3} substrates by magnetron sputtering were fully relaxed with high crystalline quality due to high oxygen partial pressure deposition and post annealing at 950 °C. The lattice constants of the BSTO buffer layers could be controlled in the range of 0.3926–0.3973 nm by changing the Ba content (y = 0.2–0.7). These BSTO buffer layers allow coherent growth of SLCO thin films, and a clear dependence of the superconducting transition temperature on the lattice strain was observed. The fabrication of these BSTO/superconductor heterostructures may provide novel devices composed of functional perovskite thin films, in addition to a general approach for the precise control of lattice strain in functional perovskite thin films. - Highlights: • Ba{sub y}Sr{sub 1−y}TiO{sub 3} buffer layers were developed for the strain tuning of perovskite-related oxides. • Strain effect in Sr{sub 1−x}La{sub x}CuO{sub 2} was investigated by using Ba{sub y}Sr{sub 1−y}TiO{sub 3} buffer layers. • Ba{sub y}Sr{sub 1−y}TiO{sub 3} buffer layers can be used to tune the strain in other perovskite oxides.

White light emission and effect of annealing on the Ho{sup 3+}–Yb{sup 3+} codoped BaCa{sub 2}Al{sub 8}O{sub 15} phosphor

Energy Technology Data Exchange (ETDEWEB)

Kumari, Astha; Rai, Vineet Kumar, E-mail: vineetkrrai@yahoo.co.in

2015-12-15

Graphical abstract: The upconversion emission spectra of the Ho{sup 3+}/Yb{sup 3+} doped/codoped BaCa{sub 2}Al{sub 8}O{sub 15} phosphors with different doping concentrations of Ho{sup 3+}/Yb{sup 3+} ions along with UC emission spectrum of the white light emitting phosphor annealed at 800 °C. - Highlights: • BaCa{sub 2}Al{sub 8}O{sub 15} phosphors codoped with Ho{sup 3+}–Yb{sup 3+} have been prepared by combustion method. • Phosphor annealed at 800 °C, illuminate an intense white light upon NIR excitation. • The sample annealed at higher temperatures emits in the pure green region. • The colour emitted persists in the white region even at high pump power density. • Developed phosphor is suitable for making upconverters and WLEDs. - Abstract: The BaCa{sub 2}Al{sub 8}O{sub 15} (BCAO) phosphors codoped with suitable Ho{sup 3+}–Yb{sup 3+} dopant concentration prepared by combustion method illuminate an intense white light upon near infrared diode laser excitation. The structural analysis of the phosphors and the detection of impurity contents have been performed by using the X-Ray Diffraction, FESEM and FTIR analysis. The purity of white light emitted from the sample has been confirmed by the CIE chromaticity diagram. Also, the white light emitted from the sample persists with the variation of pump power density. The phosphors emit upconversion (UC) emission bands in the blue, green and red region (three primary colours required for white light emission) along with one more band in the near infrared region of the electromagnetic spectrum. On annealing the white light emitting sample at higher temperatures, the sample starts to emit green colour and also the intensity of green and red UC emission bands get enhanced largely.

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu2+, Dy3+ phosphors prepared by solid state reaction method

International Nuclear Information System (INIS)

Mothudi, B.M.; Ntwaeaborwa, O.M.; Kumar, A.; Sohn, K.; Swart, H.C.

2012-01-01

Long persistent SrAl 2 O 4 :Eu 2+ phosphors co-doped with Dy 3+ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl 2 O 4 were observed in all the samples. The broad band emission spectra at 497 nm for SrAl 2 O 4 :Eu 2+ , Dy 3+ were observed and the emission is attributed to the 4f 6 5d 1 to 4f 7 transition of Eu 2+ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy 3+ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.

Synthesis and luminescence characterization of Pr3+ doped Sr1.5Ca0.5SiO4 phosphor

Science.gov (United States)

Vidyadharan, Viji; Mani, Kamal P.; Sajna, M. S.; Joseph, Cyriac; Unnikrishnan, N. V.; Biju, P. R.

2014-12-01

Luminescence properties of Pr3+ activated Sr1.5Ca0.5SiO4 phosphors synthesized by solid state reaction method are reported in this work. Blue, orange red and red emissions were observed in the Pr3+ doped sample under 444 nm excitation and these emissions are assigned as 3P0 → 3H4, 3P0 → 3H6 and 3P0 → 3F4 transitions. The emission intensity shows a maximum corresponding to the 0.5 wt% Pr3+ ion. The decay analysis was done for 0.05 and 0.5 wt% Pr3+ doped samples for the transition 3P0 → 3H6. The life times of 0.05 and 0.5 wt% Pr3+ doped samples were calculated by fitting to exponential and non-exponential curve respectively, and are found to be 156 and 105 μs respectively. The non-exponential behaviour arises due to the statistical distribution of the distances between the ground state Pr3+ ions and excited state Pr3+ ions, which cause the inhomogeneous energy transfer rate. The XRD spectrum confirmed the triclinic phase of the prepared phosphors. The compositions of the samples were determined by the energy dispersive X-ray spectra. From the SEM images it is observed that the particles are agglomerated and are irregularly shaped. IR absorption bands were assigned to different vibrational modes. The well resolved peaks shown in the absorption spectra are identical to the excitation spectra of the phosphor samples. Pr3+ activated Sr1.5Ca0.5SiO4 phosphors can be efficiently excited with 444 nm irradiation and emit multicolour visible emissions. From the CIE diagram it can be seen that the prepared phosphor samples give yellowish-green emission.

Effect of charge compensator ions (R+ = Li+, Na+ and K+) on Sr2MgSi2O7:Dy3+ phosphors by solid-state reaction method

Science.gov (United States)

Sahu, Ishwar Prasad

2016-09-01

The Sr2MgSi2O7:Dy3+ and Sr2MgSi2O7:Dy3+, R+ (R+ = Li+, Na+ and K+) phosphors were prepared by solid-state reaction method. The crystal structures of sintered phosphors were an akermanite-type structure which belongs to the tetragonal crystallography. The prepared phosphors were excited at 350 nm, and their corresponding emission spectrum were recorded at blue (482 nm) and yellow (575 nm) region due to the 4F9/2 → 6H15/2 and 4F9/2 → 6H13/2 transitions, respectively, of Dy3+ ions. Commission Internationale de L'Eclairage coordinates have been calculated for each sample and its value exhibited that overall emission is near white light. The possible mechanisms of discussed white light emitting phosphors were also investigated. In order to investigate the suitability of the samples as white color light sources for industrial uses, color purity, correlated color temperature (CCT) and color rendering index (CRI) were calculated. Values of color purity, CCT and CRI were found well within the defined acceptable range. With incorporating (R+ = Li+, Na+ and K+) as charge compensator ions, the emission intensity of Sr2MgSi2O7:Dy3+ can be obviously enhanced. The results indicate that prepared phosphors may be a potential application in display devices.

Effect of charge compensator ions (R+ = Li+, Na+ and K+) on Sr2MgSi2O7:Dy3+ phosphors by solid-state reaction method

International Nuclear Information System (INIS)

Sahu, Ishwar Prasad

2016-01-01

The Sr 2 MgSi 2 O 7 :Dy 3+ and Sr 2 MgSi 2 O 7 :Dy 3+ , R + (R + = Li + , Na + and K + ) phosphors were prepared by solid-state reaction method. The crystal structures of sintered phosphors were an akermanite-type structure which belongs to the tetragonal crystallography. The prepared phosphors were excited at 350 nm, and their corresponding emission spectrum were recorded at blue (482 nm) and yellow (575 nm) region due to the 4 F 9/2 → 6 H 15/2 and 4 F 9/2 → 6 H 13/2 transitions, respectively, of Dy 3+ ions. Commission Internationale de L'Eclairage coordinates have been calculated for each sample and its value exhibited that overall emission is near white light. The possible mechanisms of discussed white light emitting phosphors were also investigated. In order to investigate the suitability of the samples as white color light sources for industrial uses, color purity, correlated color temperature (CCT) and color rendering index (CRI) were calculated. Values of color purity, CCT and CRI were found well within the defined acceptable range. With incorporating (R + = Li + , Na + and K + ) as charge compensator ions, the emission intensity of Sr 2 MgSi 2 O 7 :Dy 3+ can be obviously enhanced. The results indicate that prepared phosphors may be a potential application in display devices. (orig.)

Photoluminescence properties and energy transfer in Ce(3+) /Dy(3+) co-doped Sr(3) MgSi(2) O(8) phosphors for potential application in ultraviolet white light-emitting diodes.

Science.gov (United States)

Yu, Hong; Zi, Wenwen; Lan, Shi; Gan, Shucai; Zou, Haifeng; Xu, Xuechun; Hong, Guangyan

2013-01-01

Sr(3) MgSi(2) O(8) :Ce(3+) , Dy(3+) phosphors were prepared by a solid-state reaction technique and the photoluminescence properties were investigated. The emission spectra show not only a band due to Ce(3+) ions (403 nm) but also as a band due to Dy(3+) ions (480, 575 nm) (UV light excitation). The photoluminescence properties reveal that effective energy transfer occurs in Ce(3+) /Dy(3+) co-doped Sr(3) MgSi(2) O(8)phosphors, and the co-doping of Ce(3+) could enhance the emission intensity of Dy(3+) to a certain extent by transferring its energy to Dy(3+) . The Ce(3+) /Dy(3+) energy transfer was investigated by emission/excitation spectra, and photoluminescence decay behaviors. In Sr2.94 MgSi2 O8 :0.01Ce(3+) , 0.05Dy(3+) phosphors, the fluorescence lifetime of Dy(3+) (from 3.35 to 27.59 ns) is increased whereas that of Ce(3+) is greatly decreased (from 43.59 to 13.55 ns), and this provides indirect evidence of the Ce(3+) to Dy(3+) energy transfer. The varied emitted color of Sr(3) MgSi(2) O(8):Ce(3+) , Dy(3+) phosphors from blue to white were achieved by altering the concentration ratio of Ce(3+) and Dy(3+) . These results indicate Sr(3) MgSi(2) O(8):Ce(3+) , Dy(3+) may be as a candidate phosphor for white light-emitting diodes. Copyright © 2012 John Wiley & Sons, Ltd.

Chemical, structural and magnetic studies of new mono- and diphosphates appearing in ternary diagrams AO-CuO-(P2O5); A= Mg, Ca, Sr, Ba

International Nuclear Information System (INIS)

Moqine, A.

1990-01-01

A systematic study of mixed mono- and diphosphates of AO-CuO-(P 2 O 5 ) systems (A= Mg, Ca, Sr, Ba) has been carried out. This study showed up, on one hand, continuous and wide ranges in magnesium system and on the other hand, eight new phases in the other systems: Sr sub 18 Cu sub 3 (PO 4 ) 14 , A 2 Cu (PO 4 ) 2 , (A= Sr, Ba), Sr 3 Cu 3 (PO 4 ) 4 , BaCu 2 (PO 4 ) 2 and ACu(P 2 O 7 ) (A= Ca, Sr, Ba). The crystalline structures of SrCu(P 2 O 7 ), BaCu(P 2 O 7 ),Sr 3 Cu 3 (PO 4 ) 4 and BaCu 2 (PO 4 ) 2 phosphates have been described and discussed. The first compound presents a Tunnel structure and the three others have Foliation structures. The magnetic behaviours of some Cu sup 2+ ions phos-phates have been correlated to their crystalline structures. The experimental data have been parametered using the Ising model and/or the Heisenberg model. In this work, three Ising theoretical models have been developed. This magnetic study showed up new chains of antiferro- or ferrimagnetic Cu sup 2+ ions. 59 figs., 32 tabs., 113 refs. (author)

Microstructure investigations of Ba-Sr mixed ferrites, using SEM technique

International Nuclear Information System (INIS)

Amighian, J.; Mozaffari, M.

1996-01-01

A series of isotropic Ba-Sr mixed ferrites were prepared, using a conventional dry technique. The starting materials were hematite by product of Isfahan steel factory, strontium carbonate from Merck company and barium carbonate obtained from local source. The principle phase of the samples was chosen to have a composition in the form of (BaO) sub 1-x (SrO) sub x nFe sub 2 O sub 3, in which x varied between 0 to l and n was varied between 5 to 6. The raw materials were thoroughly mixed and fired in an electrical furnace for 2 hours. They were then milled in an vibrating ball mill, in which the optimum milling time for each sample was obtained. After annealing at 750 degree C, the powders were compacted in a cylindrical die under 5 tons/cm sup 2. The compacts were then mixed with a binder and sintered in air for 10 minutes at their optimum temperatures. Using SEM technique, the microstructure of the samples were investigated. Using a permeameter, the coercive force Hc and remanent induction Br were measured. The microstructures obtained from SEM technique can be used to control the sintering stage in ferrite fabrication

Influences of Indium Tin Oxide Layer on the Properties of RF Magnetron-Sputtered (BaSr)TiO3 Thin Films on Indium Tin Oxide-Coated Glass Substrate

Science.gov (United States)

Kim, Tae Song; Oh, Myung Hwan; Kim, Chong Hee

1993-06-01

Nearly stoichiometric ((Ba+Sr)/Ti=1.08-1.09) and optically transparent (BaSr)TiO3 thin films were deposited on an indium tin oxide (ITO)-coated glass substrate by means of rf magnetron sputtering for their application to the insulating layer of an electroluminescent flat panel display. The influence of the ITO layer on the properties of (BaSr)TiO3 thin films deposited on the ITO-coated substrate was investigated. The ITO layer did not affect the crystallographic orientation of (BaSr)TiO3 thin film, but enhanced the grain growth. Another effect of the ITO layer on (BaSr)TiO3 thin films was the interdiffusion phenomenon, which was studied by means of secondary ion mass spectrometry (SIMS). As the substrate temperature increased, interdiffusion intensified at the interface not only between the grown film and ITO layer but also between the ITO layer and base glass substrate. The refractive index (nf) of (BaSr)TiO3 thin film deposited on a bare glass substrate was 2.138-2.286, as a function of substrate temperature.

Dielectric and Energy Storage Properties of Ba0.65Sr0.35TiO3 Ceramics Modified by BiNbO4

Science.gov (United States)

Zheng, Yi; Zhang, Jihua; Wei, Meng; Dong, Xiangxiang; Huang, Jiapeng; Wu, Kaituo; Chen, Hongwei

2018-02-01

(1 - x) (Ba0.65Sr0.35TiO3)-xBiNbO4 (x = 0.0-0.15) ceramic were prepared by solid-state reaction method. The phase composition, microstructure, dielectric properties, polarization-electric field, breakdown strength and energy storage behaviors for the BiNbO4-modified Ba0.65Sr0.35TiO3 ceramics were investigated. With the addition of BiNbO4, the remnant polarization and saturation polarization decreased and the nonlinearity was suppressed. When x = 0.07, the maximum recoverable energy storage achieved was 0.5 J/cm3, 1.5 times that of un-doped Ba0.65Sr0.35TiO3 ceramics, with an efficiency of 96.89% and a breakdown electric field reaching 15.3 kV/mm. Therefore, BiNbO4 doping could improve the energy storage properties of Ba0.65Sr0.35TiO3 for high-energy pulse capacitor application.

The influences of mole composition of strontium (x) on properties of barium strontium titanate (Ba{sub 1−x}Sr{sub x}TiO{sub 3}) prepared by solid state reaction method

Energy Technology Data Exchange (ETDEWEB)

Sandi, Dianisa Khoirum; Supriyanto, Agus; Iriani, Yofentina, E-mail: yopen-2005@yahoo.com [Physics Department, Faculty of Mathematics and Natural Science, Sebelas Maret University (Indonesia); Jamaluddin, Anif [Physics Department, Faculty of Teacher Training and Education, Sebelas Maret University (Indonesia)

2016-02-08

Barium Strontium Titanate (Ba{sub 1-x}Sr{sub x}TiO{sub 3}) or BST was prepared by solid state reaction method. Raw materials are BaCO{sub 3}, SrCO{sub 3}, and TiO{sub 2}. Those materials are mixed for 8 h, pressed, and sintered at temperature 1200°C for 2 h. Mole composition of Sr (x) was varied to study its influences on structural, morphological, and electrical properties of BST. Variation of (x) are x = 0; x = 0.1; and x = 0.5. XRD patterns showed a single phase of BST, which mean that mixture of raw materials was homogenous. Crystal structure was influenced by x. BaTiO{sub 3} and Ba{sub 0.9}Ti{sub 0.1}TiO{sub 3} have tetragonal crystal structure, while Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} is cubic. The diffraction angle shifted to right side (angle larger) as the increases of x. Crystalline size of BaTiO{sub 3}, Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3}, and Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} are 38.13 nm; 38.62 nm; and 37.13 nm, respectively. SEM images showed that there are still of pores which were influenced by x. Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has densest surface (pores are few and small in size). Sawyer Tower circuit showed that BaTiO{sub 3} and Ba{sub 0.9}Sr{sub 0.1} TiO{sub 3} is ferroelectric, while Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} is paraelectric. The dielectric constants of BaTiO{sub 3}, Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} and Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} at frequency of 1 KHz are 156; 196; and 83, respectively. Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has relatively highest dielectric constant. It is considered that Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has densest surface.

Photoluminescence and photostimulated luminescence in the X-ray storage phosphor BaBr2 doped with cerium

International Nuclear Information System (INIS)

Corradi, G.; Secu, M.; Schweizer, S.; Spaeth, J.-M.

2004-01-01

In orthorhombic BaBr 2 : Ce 3+ two kinds of luminescence bands at room temperature have been attributed to charge-compensated Ce 3+ centres. One type was associated with potassium (or some other monovalent cation) on a neighbouring Ba site and another one associated with an unidentified defect. A third kind of emission, observed only as low temperature photoluminescence (PL), is ascribed to isolated Ce 3+ ions. The charge-compensated Ce 3+ complexes are active both in PL and photostimulated luminescence (PSL) following X-ray irradiation. The PSL is nearly as efficient as in the case of the commercially used X-ray storage phosphor BaFBr:Eu 2+ . The X-ray induced electrons are trapped in F-type centres whose band position is characteristic for the nearby Ce complex. As shown by the fingerprint character of the PSL itself, the hole partner in the recombination is also associated or identical with the same Ce complex

Process of radiation damage in BaFX:Eu2+ (X=Br, I) photo-stimulable phosphor for imaging plate (IP)

International Nuclear Information System (INIS)

Kato, Munetaka; Takahashi, Kenji

2005-01-01

Imaging Plate (IP) is a 2-dimensional radiation detector utilizing photo-stimulable phosphors. Photo-stimulated luminescence (PSL) is a kind of process in radiation-induced reactions and IP can be repeatedly performed. The mechanism of PSL is reviewed and the radiation damage, which is a phenomenon that the luminescence goes down under X-ray irradiation, is also referred to. The relation between the composition of BaFX: Eu 2+ (X=Br, I), which is widely used in IPs, and the degree of radiation damage is investigated. The degree of radiation damage is smaller in the mixed crystal system of Br and I such as BaFBr 0.85 I 0.15 :Eu 2+ than in BaFBr: Eu 2+ and BaFI: Eu 2+ . This is explained by the characteristics of luminescence centers and F centers under X-ray irradiation. (author)

Observation of forbidden (E2) lines in the ultraviolet spectra of Ca II, Sr II, and Ba II by inductively coupled plasma emission spectroscopy

International Nuclear Information System (INIS)

Doidge, Peter S.

2013-01-01

Forbidden (electric quadrupole, E2) transitions of the type ns 2 S 1/2 –nd 2 D 3/2 and ns 2 S 1/2 –nd 2 D 5/2 in the ultraviolet spectra of singly ionized Ca, Sr, and Ba (with n = 4, 5 or 6 for Ca, Sr, and Ba, respectively) have been observed in the emission spectrum of an inductively coupled argon plasma. Wavelengths and wavenumbers of the six lines are reported and the values are in good agreement with those expected from literature data for the energy levels involved. - Highlights: • Wavelengths measured using commercially available ICP emission spectrometer • First wavelength and wavenumber measurements of some E2 lines of Ba +, Ca +, Sr + • Evidence for small plasma shifts in the wavenumbers of Ba + and Sr +

Investigations of the solid solution in the system SrI/sub 2/-BaI/sub 2/ at ambient pressures and at 2. 0 GPa

Energy Technology Data Exchange (ETDEWEB)

Beck, H.P.; Holley, C.; Limmer, A. (Erlangen-Nuernberg Univ., Erlangen (Germany, F.R.). Inst. fuer Anorganische Chemie)

1984-09-01

The P,T,x-diagram of the system SrI/sub 2/-BaI/sub 2/ has been investigated at ambient pressures and at 2.0 GPa. The amount of solid solution in the four structure types occuring in this system (SrI/sub 2/- or PbCl/sub 2/-ZrAs/sub 2/-type with SrI/sub 2/ and PbCl/sub 2/- or anti-Fe/sub 2/P-type with BaI/sub 2/) differs considerably. Structural geometries belonging to the same PbCl/sub 2/ structure family show marked differences in their toleration to cation substitution. Solid solution is especially pronounced in the BaI/sub 2/-rich phases which incorporate up to 60 mol-% Sr/sup 2 +/ in the high pressure phase of BaI/sub 2/.

Tunable emission and the systematic study on energy-transfer properties of Ce3+- and Tb3+-co-doped Sr3(PO4)2 phosphors

International Nuclear Information System (INIS)

Liu, Zhijun

2015-01-01

An emitting color tunable phosphor Sr 3 (PO 4 ) 2 :Ce 3+ , Tb 3+ was synthesized by the traditional high-temperature solid-state reaction method. The photoluminescence and energy-transfer (ET) properties of Ce 3+ - and Tb 3+ -doped Sr 3 (PO 4 ) 2 host were studied in detail. The obtained phosphors show both a blue emission from Ce 3+ and a yellowish green emission from Tb 3+ with considerable intensity under ultraviolet (UV) excitation (∝311 nm). When the content of Ce 3+ was fixed at 0.03, the emission chromaticity coordinates could be adjusted from blue to green region by tuning the contents of Tb 3+ ions with the aid of ET process. The critical distance between Ce 3+ and Tb 3+ is 14.69 A. The ET mechanism from Ce 3+ to Tb 3+ ions was identified with dipole-dipole interaction. The obtained phosphor exhibits a strong excitation in UV spectral region and high-efficient ET from Ce 3+ to Tb 3+ ions. It may find applications as a green light-emitting UV-convertible phosphor in white LED devices. (orig.)

Interface Control of Ferroelectricity in an SrRuO3 /BaTiO3 /SrRuO3 Capacitor and its Critical Thickness.

Science.gov (United States)

Shin, Yeong Jae; Kim, Yoonkoo; Kang, Sung-Jin; Nahm, Ho-Hyun; Murugavel, Pattukkannu; Kim, Jeong Rae; Cho, Myung Rae; Wang, Lingfei; Yang, Sang Mo; Yoon, Jong-Gul; Chung, Jin-Seok; Kim, Miyoung; Zhou, Hua; Chang, Seo Hyoung; Noh, Tae Won

2017-05-01

The atomic-scale synthesis of artificial oxide heterostructures offers new opportunities to create novel states that do not occur in nature. The main challenge related to synthesizing these structures is obtaining atomically sharp interfaces with designed termination sequences. In this study, it is demonstrated that the oxygen pressure (PO2) during growth plays an important role in controlling the interfacial terminations of SrRuO 3 /BaTiO 3 /SrRuO 3 (SRO/BTO/SRO) ferroelectric (FE) capacitors. The SRO/BTO/SRO heterostructures are grown by a pulsed laser deposition method. The top SRO/BTO interface, grown at high PO2 (around 150 mTorr), usually exhibits a mixture of RuO 2 -BaO and SrO-TiO 2 terminations. By reducing PO2, the authors obtain atomically sharp SRO/BTO top interfaces with uniform SrO-TiO 2 termination. Using capacitor devices with symmetric and uniform interfacial termination, it is demonstrated for the first time that the FE critical thickness can reach the theoretical limit of 3.5 unit cells. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Relativistic calculations of the fine-structure intervals of the ns2np2P terms and the ionization energies of the Ca-, Sr-and Ba- ions

International Nuclear Information System (INIS)

Wijesundera, W.P.; Vosko, S.H.; Parpia, F.A.

1996-01-01

We report new calculations of the energy differences between the ns 1/2 2 np 1/2 and ns 1/2 2 np 3/2 levels of the Ca - , Sr - and Ba - ions; here n 4, 5 and 6 for Ca - , Sr - and Ba - , respectively. The electron affinities of Ca, Ba and Sr have also been calculated. All estimates were obtained by performing a series of multiconfiguration Dirac-Fock calculations for the neutral atoms and their anions. Correlations among valence electrons in both the ground and excited states were included in these calculations. Our estimate of the fine structure of the ground state of Sr - is in good agreement with recent measurements. Our estimates of the electron affinities of Ca, Sr and Ba are in reasonable agreement with experiment. (author)

Host composition dependent tunable multicolor emission in the single-phase Ba2(Ln1-zTbz)(BO3)2Cl:Eu phosphors

NARCIS (Netherlands)

Xia, Z.; Zhuang, J.; Meijerink, A.; Jing, X.

2013-01-01

A new strategy based on the host composition design has been adopted to obtain efficient color-tunable emission from Ba2Ln0.97−zTbz(BO3)2Cl:0.03Eu (Ln = Y, Gd and Lu, z = 0–0.97) phosphors. This study reveals that the single-phase Ba2Ln1−zTbz(BO3)2Cl compounds can be applied to use allowed Eu2+

Enhancement of white-light-emission from single-phase Sr5(PO4)3F:Eu(2+),Mn(2+) phosphors for near-UV white LEDs.

Science.gov (United States)

Feng, Yaomiao; Huang, Jinping; Liu, Lili; Liu, Jie; Yu, Xibin

2015-09-07

A series of single-phase broadband white-light-emitting Sr5(PO4)3F:Eu(2+),Mn(2+) phosphors were prepared by a solid state reaction. The luminescence property, and the crystal and electronic structures of the fluorophosphates were studied by photoluminescence analysis, XRD Rietveld refinement and density functional theory calculation (DFT), respectively. Under near ultraviolet excitation in the 250 to 430 nm wavelength range, the phosphors exhibit two emission bands centered at 440 and 556 nm, caused by the Eu(2+) and Mn(2+) ions. By altering the relative ratios of Eu(2+) and Mn(2+) in the compounds, the emission color could be modulated from blue to white. The efficient energy transfer from the Eu(2+) to Mn(2+) ions could be ascribed to the well crystallized host lattice and the facile substitution of Eu(2+) and Mn(2+) for Sr(2+) sites due to similar ionic radii. A series of fluxes were investigated to improve the photoluminescence intensity. When KCl was used as flux in the synthesis, the photoluminescence intensity of Sr5(PO4)3F:Eu(2+),Mn(2+) was enhanced by 85% compared with no fluxes added. These results demonstrate that the single-phase Sr5(PO4)3F:Eu(2+),Mn(2+) with enhanced luminescence efficiency could be promising as a near UV-convertible direct white-light-emitting phosphor for WLED applications.

Surface morphology analysis of nanostructured (Ba sub x , Sr sub 1 sub - sub x)TiO sub 3 thin films using fractal method

CERN Document Server

Hong, K J; Choi, W K; Cho, J C

2003-01-01

Based on the fractal theory, this paper uses scanning electron microscopy images to investigate the roughness characteristics of nanostructured (Ba Sr)TiO sub 3 thin films by sol-gel methods. The percentage grain area, surface fractal dimensions and 3D image are evaluated using image analysis methods. The thickness of the (Ba Sr)TiO sub 3 thin films was 260-280 nm. The surface fractal dimensions were increased with strontium doping, and grain area, were decreased with it. The fractal dimension and the grain areas of the (Ba sub 0 sub . sub 7 Sr sub 0 sub . sub 3)TiO sub 3 thin films were 1.81 and 81%. Based on the image analysis, the roughness height of 3D images as 256 levels was about 3 nm and its distribution was about 35-40% for the (Ba sub 0 sub . sub 8 Sr sub 0 sub . sub 2)TiO sub 3 and (Ba sub 0 sub . sub 7 Sr sub 0 sub . sub 3)TiO sub 3 thin films. The roughness height of the BST thin films was distributed from 35% to 40% ranging from 3 nm to 4 nm. By increasing the strontium doping, the roughness hei...

Band-gap tuning and magnetic properties of heterovalent ions (Ba, Sr and Ca) substituted BiFeO_3 nanoparticles

International Nuclear Information System (INIS)

Chauhan, Sunil; Kumar, Manoj; Katyal, S. C.

2016-01-01

A Comparative study of heterovalent Ba, Sr and Ca ions substitution on the structural, vibrational, optical and magnetic properties of BiFeO_3 nanoparticles was carried out. The distorted rhombohedral structure was confirmed from both X-ray diffraction and Raman spectroscopy techniques in pure BiFeO_3 and Bi_0_._8_5A_0_._1_5FeO_3 (A= Ba, Sr and Ca) samples. UV-Visible spectroscopy results show that the band-gap of BiFeO_3 nanoparticles can be tuned by heterovalent ions substitution from 2.12 eV for BiFeO_3 to 2.10, 2.06 and 2.03 eV for Ca, Sr and Ba substituted BiFeO_3 nanoparticles respectively. The magnetic measurements indicate enhancement in magnetization for heterovalent A"2"+ substituted BiFeO_3 samples and the magnetization increases with increase of ionic radius of the substituted ions.

Study of photo-stimulated luminescence in Ba0.95M0.05FBr:Eu2+ (M = Sr, Ca) powder

International Nuclear Information System (INIS)

Zhou Yingxue; Wang Dongsheng; Zhang Xinyi

2001-01-01

The luminescence centered at about 390 nm due to 4f 6 5d→4f 7 transition of Eu 2+ can be observed without X-ray or UV-light pre-irradiation for BaFBr:Eu 2+ , Ba 0.95 Sr 0.05 FBr:Eu 2+ and Ba 0.95 Ca 0.05 FBr:Eu 2+ powder samples which can be excited by light with wave length longer than 400 nm. It could be attributed to F centers which are formed in the preparation of samples. There are two broad bands in the photo-stimulated spectra. One peaked at 535 nm results from the excitation of electrons at F(F - ) center, and the other at 708 nm might be originated from the electron excitation of F(Br - ) center or F(Br - ) accumulators. If the Ba 2+ (ion's radius equals to 0.135 nm) in the samples were replaced by about 50% mol. of Sr 2+ (ion's radius equals to 0.113 nm) or Ca 2+ (ion's radius equals to 0.099 nm), the intensities of 535 nm and 708 nm bands decrease with the decreasing of ion radius. On the other hand, the shoulders at 580 nm and 650 nm or 575 nm and 645 nm can appear. In absorption spectra of 50-400 nm range, one can observe the red-shift of 79 nm, 83 nm peaks and new absorption peaks. It means that the new color centers: F(F - , Sr 2+ ), F(br - , Sr 2+ ) or F(F - , Ca 2+ ), F(br - , Ca 2+ ) are formed, when Ba 2+ were replaced with Sr 2+ or Ca 2+ in samples. It corresponds to the shoulders in photo-stimulated spectra

The effect of doping Mg2+ on structure and properties of Sr(1.992-x)MgxSiO4: 0.008Eu2+ blue phosphor synthesized by co-precipitation method

Science.gov (United States)

Yang, Lingxiang; Wang, Jin-shan; Zhu, Da-chuan; Pu, Yong; Zhao, Cong; Han, Tao

2018-01-01

In order to improve the luminescence property of silicate phosphors, a series of Sr(1.992-x)MgxSiO4: 0.008Eu2+(x = 0, 0.25, 0.50, 0.75) blue phosphors have been synthesized using one-step calcination of a precursor prepared by chemical co-precipitation. And then the crystal structure and luminescence properties of the phosphors are investigated by means of X-Ray Diffraction and spectrophotometer. The results show that β-phase existed in the mixed phases of Sr2SiO4 (β+α‧) would transform to α‧-phase with Mg2+ ions doping into the silicate host until it disappeared. On the other hand, the introduction of Mg2+ ions can enhance the intensity of the excitation spectrum and promote the excitation sensitivity of Sr(1.992-x)MgxSiO4: 0.008Eu2+ phosphors in NUV region. Under NUV excitation at 350 nm, all samples exhibit a broadband emission in range of 400-550 nm due to the 4f65d1→4f7(8S7/2) transition of Eu2+ ions. According to Multi-peak fitting to emission spectra by Gauss method, the broad emission band consists of two single bands with peaks Em1 and Em2 locating at 460 and 490 nm, which corresponds to Eu2+ ions occupying the ten-fold oxygen-coordinated Sr1 site and the nine-fold oxygen-coordinated Sr2 site, respectively. The luminescence intensity of Sr(1.992-x)MgxSiO4:0.008Eu2+(x = 0, 0.25, 0.50, 0.75) blue phosphors has been enhanced remarkably after Mg2+ ions are added. Meanwhile, the chromaticity coordinates change from the blue-green region to the blue region as x moves from 0 to 0.75. Moreover, the decay curves are measured and can be well fitted with double exponential decay equation. It shows that the average lifetime is extended with the concentration of Mg2+ ions increasing. These results indicate that Sr(1.992-x)MgxSiO4: 0.008Eu2+(x = 0, 0.25, 0.50, 0.75) can be used as a potential blue phosphor in near UV-excited white LEDs.

Perovskite phases in the systems AO-SE/sub 2/O/sub 3/-UO/sub 2,x/ with A=alkaline earth metal and SE=rare earths, La, and Y. IX. The systems Ba/sub 2/SrUO/sub 6/-Ba/sub 2/Gd/sub 0. 67/UO/sub 6/ and Ba/sub 2/SrUO/sub 6/-Ba/sub 2/Y/sub 0. 67/UO/sub 6/

Energy Technology Data Exchange (ETDEWEB)

Kemmler-Sack, S; Seemann, I [Tuebingen Univ. (F.R. Germany). Inst. fuer Anorganische Chemie I

1976-07-01

The ordered perovskite Ba/sub 2/SrUO/sub 6/ forms a solid solution series with Ba/sub 2/Gdsub(0.67)UO/sub 6/ and Ba/sub 2/Ysub(0.67)UO/sub 6/ respectively. The deviations from the ideal behaviour are studied by X-ray, diffuse reflectance and vibrational methods.

EXAFS and EPR study of La0.6Sr0.2Ca0.2MnO3 and La0.6Sr0.2Ba0.2MnO3

International Nuclear Information System (INIS)

Yang, D.-K.Dong-Seok; Ulyanov, A.N.; Phan, Manh-Huong; Kim, Ikgyun; Ahn, Byong-Keun; Rhee, Jang Roh; Kim, Jung Sun; Nguyen, Chau; Yu, Seong-Cho

2003-01-01

Extended X-ray absorption fine structure (EXAFS) analysis and electron-paramagnetic resonance (EPR) have been used to examine the local structure and the internal dynamics of La 0.6 Sr 0.2 Ca 0.2 MnO 3 and La 0.6 Sr 0.2 Ba 0.2 MnO 3 lanthanum manganites. The Mn-O bond distance (∼1.94 Angst for both samples) and the Debye-Waller factors (0.36x10 -2 and 0.41x10 -2 Angst 2 for La 0.6 Sr 0.2 Ca 0.2 MnO 3 and for La 0.6 Sr 0.2 Ba 0.2 MnO 3 , respectively) were obtained from the EXAFS analysis. The dependence of the EPR line width on dopant kind (Ca or Ba) showed a decrease of the spin-lattice interaction with an increase of the Curie temperature. For both compositions, the EPR line intensity followed the exponential law I(T)=I 0 exp(E a /k B T), deduced on the basis of the adiabatic polaron hopping model

Structural and thermodynamic characterization of the perovskite-related BA{sub 1+y}UO{sub 3+x} and (BA,SR){sub 1+y}UO{sub 3+x} phases

Energy Technology Data Exchange (ETDEWEB)

Cordfunke, E.H.P. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Booij, A.S. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Smit-Groen, V. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Vlaanderen, P. van [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); IJdo, D.J.W. [Rijksuniversiteit Leiden (Netherlands). Gorlaeus Labs.

1996-11-01

The perovskite-type BaUO{sub 3} structure has been investigated by X-ray and neutron diffraction. The Ba/U ratio, the (Ba, Sr)/U ratio, and the oxygen stoichiometry in Ba{sub 1+y}UO{sub 3+x} were varied, and the integral enthalpies of formation determined by solution calorimetry. In addition, equilibrium oxygen partial pressures were measured using a reversible EMF cell. The chemical defect mechanism is discussed, and it is shown that a continuous series BaUO{sub 3}-Ba{sub 1+y}UO{sub 3+x}-Ba{sub 3}UO{sub 6} exist in which uranium vacancies are gradually filled up with barium ions, whereas uranium is oxidized via the pentavalent to the hexavalent state in Ba{sub 3}UO{sub 6}(=Ba{sub 2}(Ba, U)O{sub 6}). (orig.).

Electrical properties and structure of glasses in the Ba(PO3)2-MF2 systems, where M = Mg, Ca, Sr, Ba

International Nuclear Information System (INIS)

Sokolov, I.A.; Tarlakov, Yu.P.; Murin, I.V.; Pronkin, A.A.

2000-01-01

Using the methods of conductometry and IR spectroscopy the concentrational dependences of electric conductivity are studied, the nature of current carriers is determined, the concentrational dependence of transfer numbers is ascertained and structural changes in glasses of the system Ba(PO 3 ) 2 -MF 2 (M = Mg, Ca, Sr, Ba), depending on MF 2 content, are considered. It is shown that F - ions take part in electric current transfer. Influence of crystallochemical nature of alkaline-earth cations on physicochemical properties and structure of the glasses studied is analyzed [ru

Luminescent and morphological study of Sr2CeO4 blue phosphor prepared from oxalate precursors

International Nuclear Information System (INIS)

Ferrari, Jefferson L.; Pires, Ana M.; Serra, Osvaldo A.; Davolos, Marian R.

2011-01-01

Luminescent and morphological studies of Sr 2 CeO 4 blue phosphor prepared from cerium-doped strontium oxalate precursor are reported. Powder samples were prepared from 5 and 25 mol% Ce 3+ -doped strontium oxalate as well as from a mechanical mixture of strontium oxalate and cerium oxalate at a 4:1 ratio, respectively. All the samples were characterized by XRD, IR, PLS, and SEM. The luminescent and structural properties of the Sr 2 CeO 4 material are little affected by the SrCO 3 remaining from precursors. The Sr 2 CeO 4 material consists in one-dimensional chains of edge-sharing CeO 6 octahedra that are linked together by Sr 2+ ions. The carbonate ion might be associated with oxygen ions of the linear chain, and also with the oxygen atoms located in the equatorial position, which consequently affects the charge transfer bands between O 2- and Ce 4+ . As observed by SEM, the morphological changes are related to each kind of precursor and thermal treatment, along with irregular powder particles within the size range 0.5-2 μm.

Nano-SIMS analysis of Mg, Sr, Ba and U in natural calcium carbonate

International Nuclear Information System (INIS)

Sano, Yuji; Shirai, Kotaro; Takahata, Naoto; Hirata, Takafumi; Sturchio, Neil C.

2005-01-01

Concentrations of minor (Mg and Sr) and trace (Ba and U) elements in four natural calcium carbonate samples were first analyzed by inductively coupled plasma mass spectrometry (ICP-MS) after chemical dissolution and calibrated against a standard dolomite. Their homogeneities were checked by in situ laser ablation (LA) ICP-MS with 10-20 spots. The carbonate samples were measured by using a high lateral resolution secondary ion mass spectrometer (Nano-SIMS NS50). A ∼4 nA O - primary beam was used to sputter a 5 - 6-μm diameter crater on the sample surface, and secondary positive ions were extracted for mass analysis using an accelerating voltage of 8 kV and a Mattauch-Herzog geometry. A multi-collector system was adjusted to detect 26 Mg + , 43 Ca + , 88 Sr + , 138 Ba + , 238 U 16 O 2 + ions at the same time. A resolving power of 2500 - 5000 at 10% peak height was attained by an entrance slit set at 40 μm, and each exit slit at 50 μm with adequate flat-topped peaks. The observed 26 Mg/ 43 Ca, 88 Sr/ 43 Ca, 138 Ba/ 43 Ca and 238 U 16 O 2 / 43 Ca ratios agreed well with those measured by LA-ICP-MS. Foraminifera shells were analyzed at 5 - 6 μm scale by Nano-SIMS. There was a large variation of the Mg/Ca ratios, up to ±38%, even in a single fragment of the shell, suggesting that although the ratios provide a useful paleoceanographic proxy at bulk scale, they may reflect a more complex pattern at <10 μm scale. (author)

Rapid formation of red long afterglow phosphor Sr3Al2O6:Eu2+, Dy3+ by microwave irradiation

International Nuclear Information System (INIS)

Zhang Ping; Xu Mingxia; Zheng Zhentai; Sun Bo; Zhang Yanhui

2007-01-01

A new red long afterglow phosphor Sr 3 Al 2 O 6 :Eu 2+ , Dy 3+ nanocrystalline particles were prepared using a microwave oven operated at a frequency of 2.45 GHz and a power of 680 W in a weak reductive atmosphere. The phosphor nanocrystalline particles were characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and fluorescence spectrophotometer. The results reveal that the samples are composed of single Sr 3 Al 2 O 6 phase. The obtained nanocrystalline particles show small size (80-100 nm) and spherical shape. The excitation and emission spectra indicate that excitation broadband chiefly lies in visible range and the nanocrystalline particles emit strong light at 612 nm under around 473 nm excitation. The effect of Eu 2+ doping concentrations of the samples on the emission intensity is studied systematically. Furthermore, comparing with conventional heating method, the microwave method has the advantages such as short heating time and low energy consumption. However, the decay speed of the afterglow for Sr 3 Al 2 O 6 :Eu 2+ , Dy 3+ nanocrystalline particles is faster than that obtained by the conventional heating method

The photoluminescent property and optical transition analysis of host sensitized Ca{sub 0.5}Sr{sub 0.5}MoO{sub 4}:Dy{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Yang, Zhiping; Hou, Chuncai [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China); Duan, Guangjie [College of Electronics and Information Engineering, Hebei University, Baoding, Hebei 071002 (China); Yang, Fu [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China); College of Science, Hebei North University, Zhangjiakou 075000 (China); Liu, Pengfei; Wang, Can [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China); Liu, Lipeng [College of Electronics and Information Engineering, Hebei University, Baoding, Hebei 071002 (China); Dong, Guoyi, E-mail: dongguoyitxzz@163.com [College of Physics and Technology, Hebei University, Baoding, Hebei 071002 (China)

2014-08-01

Highlights: • A novel host sensitized Ca{sub 0.5−x}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} phosphors could be synthesized by solid state reaction. • The XRD and SEM figures were made to analyze the crystal phase and morphology of Ca{sub 0.5−x}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} phosphors. • We research the emission and excitation properties by analyzing the relevant optical transition. • The energy transition is proved to exist by the analysis on luminescence spectra and luminescence decay curves. • The chromaticity coordinate of Ca{sub 0.5−x}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} will be tunable as changing x. - Abstract: A series of Dy{sup 3+} doped Ca{sub 0.5}Sr{sub 0.5}MoO{sub 4} phosphors were synthesized by solid state reaction. The structure and the photoluminescent (PL) properties of the as-prepared powders were characterized by X-ray diffraction (XRD), field emission scanning electron microscope and fluorescent spectrophotometry. The analyses on optical transition of Ca{sub 0.5}Sr{sub 0.5}MoO{sub 4}:xDy{sup 3+} phosphors indicate that the broad band of excitation spectrum comes from the charge transmission. The broad band of excitation spectrum matches well with the excitation energy level of Dy{sup 3+}, indicating the energy transfer from the host to Dy{sup 3+}. The chromaticity coordinates changed from blue–green to yellow area depending on the Dy{sup 3+} concentration. In addition, the main mechanism of the concentration quenching was the electric multiple interaction between Dy{sup 3+} ions.

Electronic structure of (La,Sr)2CuO4 and Ba0.6K0.4BiO3

International Nuclear Information System (INIS)

Howell, R.H.; Sterne, P.A.; Fluss, M.J.; Kaiser, J.H.; Kitazawa, K.; Kojima, H.; Mosley, W.D.; Dykes, J.W.; Shelton, R.N.

1995-01-01

We have measured and calculated the electron-positron momentum distribution of La 2-x Sr x CuO 4 samples for Sr concentrations of 0, 0.1,0.13, and 0.2 and Ba 0.6 K 0.4 BiO 3 . The momentum distribution of all samples contained features derived from the overlap of the positron distribution with the valence electrons. In addition, discontinuities typical of a Fermi surface are seen in the superconducting samples. The form and position of these features are in general agreement with band theory for both La 2-x Sr x CuO 4 and Ba 0.6 K 0.4 BiO 3 . However the evolution of the Fermi surface with doping in La 2-x Sr x CuO 4 differed significantly from expectations based on single electron band theories. (orig.)

Electrical transport across nanometric SrTiO3 and BaTiO3 barriers in conducting/insulator/conducting junctions

Science.gov (United States)

Navarro, H.; Sirena, M.; González Sutter, J.; Troiani, H. E.; del Corro, P. G.; Granell, P.; Golmar, F.; Haberkorn, N.

2018-01-01

We report the electrical transport properties of conducting/insulator/conducting heterostructures by studying current-voltage IV curves at room temperature. The measurements were obtained on tunnel junctions with different areas (900, 400 and 100 μm2) using a conducting atomic force microscope. Trilayers with GdBa2Cu3O7 (GBCO) as the bottom electrode, SrTiO3 or BaTiO3 (thicknesses between 1.6 and 4 nm) as the insulator barrier, and GBCO or Nb as the top electrode were grown by DC sputtering on (100) SrTiO3 substrates For SrTiO3 and BaTiO3 barriers, asymmetric IV curves at positive and negative polarization can be obtained using electrodes with different work function. In addition, hysteretic IV curves are obtained for BaTiO3 barriers, which can be ascribed to a combined effect of the FE reversal switching polarization and an oxygen vacancy migration. For GBCO/BaTiO3/GBCO heterostructures, the IV curves correspond to that expected for asymmetric interfaces, which indicates that the disorder affects differently the properties at the bottom and top interfaces. Our results show the role of the interface disorder on the electrical transport of conducting/insulator/conduction heterostructures, which is relevant for different applications, going from resistive switching memories (at room temperature) to Josephson junctions (at low temperatures).

Influence of Ba²⁺ and Sr²⁺ ions on the hydration process of portland cement and blended cements

OpenAIRE

Živanović, B. M.; Petrašinović, Lj.; Milovanović, T.; Karanović, Lj.; Krstanović, I.

1987-01-01

This study concerns the influence of the concentration of Sr2+ and Ba2+ ions in mortar batch waters upon the hydration process of various Portland and additive cements. An increase in the mechanical resistence of said cements is observed, after 28 days, when the concentration of Ba2+ and Sr2+ ions in the mortar batch waters increases. This suggests a possible microstructural explanation of said phenomenon.En el presente trabajo se estudia la influencia de la concentración de los iones Sr2+ y...

Study of non-stoichiometric BaSrTiFeO3 oxide dedicated to semiconductor gas sensors

International Nuclear Information System (INIS)

Fasquelle, D.; Verbrugghe, N.; Deputier, S.

2016-01-01

Developing instrumentation systems compatible with the European RoHS directive (restriction of hazardous substances) to monitor our environment is of great interest for our society. Our research therefore aims at developing innovating integrated systems of detection dedicated to the characterization of various environmental exposures. These systems, which integrate new gas sensors containing lead-free oxides, are dedicated to the detection of flammable and toxic gases. We have firstly chosen to study semiconductor gas sensors implemented with lead-free oxides in view to develop RoHS devices. Therefore thick films deposited by spin-coating and screen-printing have been chosen for their robustness, ease to realize and ease to finally obtain cost-effective sensors. As crystalline defects and ionic vacancies are of great interest for gas detection, we have decided to study a non-stoichiometric composition of the BaSrTiFeO 3 sensible oxide. Nonstoichiometric BaSrTiFeO 3 lead-free oxide thick films were deposited by screen-printing on polycrystalline AFO 3 substrates covered by a layer of Ag-Pd acting as bottom electrode. The physical characterizations have revealed a crystalline structure mainly composed of BaTiO 3 pseudo-cubic phase and Ba 4 Ti 12 O 27 monoclinic phase for the powder, and a porous microstructure for the thick films. When compared to a BSTF thick film with a stoichiometric composition, a notable increase in the BSTF dielectric constant value was observed when taking into account of a similar microstructure and grain size. The loss tangent mean value varies more softly for the non-stoichiometric BaSrTiFeO 3 films than for the perovskite BSTF film as tanδ decreases from 0.45 to 0.04 when the frequency increases from 100 Hz to 1 MHz. (paper)

Host sensitized near-infrared emission in Nd3+ doped different alkaline-sodium-phosphate phosphors

Science.gov (United States)

Balakrishna, A.; Swart, H. C.; Kroon, R. E.; Ntwaeaborwa, O. M.

2018-04-01

Near-infrared (NIR) emitting phosphors of different alkaline based sodium-phosphate (MNa[PO4], where M = Mg, Ca, Sr and Ba were prepared by a conventional solution combustion method with fixed doping concentration of Nd3+ (1.0 mol%). The phosphors were characterized by powder X-ray diffraction, field emission scanning electron microscope, Fourier transform infrared spectroscopy, UV-vis spectroscopy and fluorescent spectrophotometry. The optical properties including reflectance, excitation and emission were investigated. The excitation spectra of the phosphors were characterized by a broadband extending from 450 to 900 nm. Upon excitation with a wavelength of 580 nm, the phosphor emits intensely infrared region at 872 nm, 1060 nm and 1325 nm which correspond to the 4F3/2 → 4I9/2, 4F3/2 → 4I11/2 and 4F3/2 → 4I13/2 transitions of Nd3+ ions and were found to vary for the different hosts. The strongest emission wavelength reaches 1060 nm. The most intense emission of Nd3+ was observed from Ca2+ incorporated host. The down conversion emissions of the material fall in the NIR region suggesting that the prepared phosphors have potential application in the development of photonic devices emitting in the NIR.

Systems of Ba(PO3)2-Sr(Pu3)2, Cd(PO3)2-Ca(PO3)2

International Nuclear Information System (INIS)

Tokman, I.A.; Bukhalova, G.A.

1977-01-01

Phase diagrams of the Ba(PO 3 ) 2 -Sr(PO 3 ) 2 and Cd(PO 3 ) 2 -Ca(PO 3 ) 2 systems have been studied and plotted by the methods of differential-thermal analysis (DTA), visual-polythermal, X-ray phase and infrared spectroscopy. The Ba(PO 3 ) 2 -Sr(PO 3 ) 2 system is of the eutectic type. In the binary system Cd(PO 3 ) 2 -Ca(PO 3 ) 2 the existence of a continuous series of solid solutions with a minimum at 858 deg C and 27.5 mol.% Ca(PO 3 ) 2 has been established

Color stable phosphors for LED lamps and methods for preparing them

Science.gov (United States)

Murphy, James Edward; Setlur, Anant Achyut; Camardello, Samuel Joseph

2013-11-26

An LED lamp includes a light source configured to emit radiation with a peak intensity at a wavelength between about 250 nm and about 550 nm; and a phosphor composition configured to be radiationally coupled to the light source. The phosphor composition includes particles of a phosphor of formula I, said particles having a coating composition disposed on surfaces thereof; ((Sr.sub.1-zM.sub.z).sub.1-(x+w)A.sub.wCe.sub.x).sub.3(Al.sub.1-ySi.sub.y-)O.sub.4+y+3(x-w)F.sub.1-y-3(x-w) I wherein the coating composition comprises a material selected from aluminum oxide, magnesium oxide, calcium oxide, barium oxide, strontium oxide, zinc oxide, aluminum hydroxide, magnesium hydroxide, calcium hydroxide, barium hydroxide, strontium hydroxide, zinc hydroxide, aluminum phosphate, magnesium phosphate, calcium phosphate, barium phosphate, strontium phosphate, and combinations thereof; and A is Li, NA, K, or Rb, or a combination thereof; M is Ca, Ba, Mg, Zn, or a combination thereof; and 0

Structural study of Sr0.3Ba0.7Nb2O6 and La0.030Sr0.255Ba0.700Nb2O6 ceramic systems

International Nuclear Information System (INIS)

Luna-Lopez, J.A.; Portelles, J.; Raymond, O.; Siqueiros, J.M.

2009-01-01

Sr 0.3 Ba 0.7 Nb 2 O 6 (SBN) and La 0.030 Sr 0.255 Ba 0.700 Nb 2 O 6 (LSBN) ceramic compounds have been prepared using the traditional ceramic method at two different calcination temperatures (900 and 1000 deg. C) and later sintered both at 1400 deg. C. A study of the effects of the calcination temperatures and La substitution on the morphological, compositional, and structural properties of SBN and LSBN is presented using scanning electronic microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) analysis. From Rietveld refinement processes, the XRD patterns were interpreted to evaluate such effects in the structural parameters and the site occupation factors of the heavy metals and oxygen atoms. The effect of the incorporation of La resulted in a 0.25% cell contraction and turned out to be higher than the 0.08% dilation effect produced by the increase of calcination temperature. The La ion with similar effective ionic radius and higher electronegativity is incorporated into the structure occupying the A 1 site just like the Sr ions in the SBN compound. Differences in the site occupation factors between the SBN and LSBN samples lead to substantial changes in the physical properties such as temperature of relative dielectric constant maximum, relative dielectric constant, and dielectric loss, correlated with the distortion and the relative orientation of the oxygen octahedra.

Improvement of the Water Resistance of a Narrow-Band Red-Emitting SrLiAl3 N4 :Eu(2+) Phosphor Synthesized under High Isostatic Pressure through Coating with an Organosilica Layer.

Science.gov (United States)

Tsai, Yi-Ting; Nguyen, Hoang-Duy; Lazarowska, Agata; Mahlik, Sebastian; Grinberg, Marek; Liu, Ru-Shi

2016-08-08

A SrLiAl3 N4 :Eu(2+) (SLA) red phosphor prepared through a high-pressure solid-state reaction was coated with an organosilica layer with a thickness of 400-600 nm to improve its water resistance. The observed 4f(6) 5d→4f(7) transition bands are thought to result from the existence of Eu(2+) at two different Sr(2+) sites. Luminescence spectra at 10 K revealed two zero-phonon lines at 15377 (for Eu(Sr1)) and 15780 cm(-1) (for Eu(Sr2)). The phosphor exhibited stable red emission under high pressure up to 312 kbar. The configurational coordinate diagram gave a theoretical explanation for the Eu(2+/3+) result. The coated samples showed excellent moisture resistance while retaining an external quantum efficiency (EQE) of 70 % of their initial EQE after aging for 5 days under harsh conditions. White-light-emitting diodes of the SLA red phosphor and a commercial Y3 Al5 O12 :Ce(3+) yellow phosphor on a blue InGaN chip showed high color rendition (CRI=89, R9=69) and a low correlated color temperature of 2406 K. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Rapid and efficient visible light photocatalytic dye degradation using AFe2O4 (A = Ba, Ca and Sr) complex oxides

International Nuclear Information System (INIS)

Vijayaraghavan, T.; Suriyaraj, S.P.; Selvakumar, R.; Venkateswaran, R.; Ashok, Anuradha

2016-01-01

Highlights: • Alkaline earth ferrites AFe 2 O 4 (A = Ba, Ca and Sr) were synthesized by sol–gel method. • Visible light photocatalytic activity of these ferrites were studied using congo red dye degradation. • BaFe 2 O 4 exhibited the best photocatalytic activity under visible light (xenon lamp) irradiation; CaFe 2 O 4 was the best photocatalyst under natural sun light irradiation. - Abstract: Photocatalytic activity of spinel type complex oxides has been investigated in this study. Alkaline earth ferrites AFe 2 O 4 (A = Ba, Ca, Sr) were synthesized by sol–gel method. Structural characterizations reveal that the synthesized ferrites have orthorhombic crystal structures with different space groups and cell dimensions when they have different alkaline earth metals in their A site. All the synthesized ferrites exhibited their bandgap in the range 2.14–2.19 eV. Their photocatalytic activities were studied using congo red dye under sunlight and xenon lamp radiation. The substitution of Ba, Ca and Sr at A site of these ferrites had varying impact on dye degradation process. Under xenon lamp irradiation, BaFe 2 O 4 exhibited the highest percentage of dye degradation (92% after 75 min). However, CaFe 2 O 4 showed the fastest degradation of the dye (70% within 15 min). In the absence of irradiation, SrFe 2 O 4 showed the highest dye adsorption (44% after 75 min).

Properties of half metallic (Ba0.8Sr0.2)2-x La2x/3x/3FeMoO6 double perovskites

International Nuclear Information System (INIS)

Serrate, D.; De Teresa, J.M.; Blasco, J.; Morellon, L.; Ibarra, M.R.

2005-01-01

Previous work in (Ba 0.8 Sr 0.2 ) 2- x La x FeMoO 6 and Ba 1+ x Sr 1-3 x La 2 x FeMoO 6 have stated electron doping as the most important parameter in terms of T c enhancement. Here we report complementary structural, magnetic and transport properties, say a series where there is no doping and only structural parameters are changed: (Ba 0.8 Sr 0.2 ) 2- x La 2 x /3 x /3 FeMoO 6 . We propose a complete phase diagram where structural and bandfilling impact on the Curie temperature is clearly evidenced

Study on the equilibrium in the MBr2-CH3OH-H2O system (M = Sr2+, Ba2+) at 25 0C

International Nuclear Information System (INIS)

Zlateva, I.; Stoev, M.

1985-01-01

The dehydration processes in the three-component system MBr 2 -CH 3 OH-H 2 O (M = Sr 2+ , Ba 2+ ) have been studied at 25 0 C by physio-chemical analyses. Crystallization fields for the lower crystal hydrates SrBr 2 x H 2 O and BaBr 2 x H 2 O have been found. The solubility curves exhibit complex-formation processes. The dehydration and solvation processes in three-component system such as MBr 2 -CH 3 OH-H 2 O at 25 0 C with M = Mg 2+ , Ca 2+ , Sr 2+ , Ba 2+ have been discussed in general terms. (author)

The Effect Of Coupling Agent On Composite Magnet Characteristic Based On Hexa ferrite (Sr M/Ba M) With Polyester And Epoxy Binder

International Nuclear Information System (INIS)

Sudirman; Ridwan; Mujamilah; Karo Karo, Aloma; Handayani, Ari; Rukihati

2004-01-01

Magnetic composites are mixtures of hexa ferrite powder and non magnetic materials such as polymers as binders. These composites have been investigated because they are light, elastic, and cheap. In this study thermoset polymer (epoxy and polyester) were used as binders. Inside study of coupling agent added effect on mechanical properties, hardness and microstructure. The composites were prepared by mixture thermoset polymer epoxy or polyester with hexa ferrite powder Sr M (SrFe 12 O 19 ) or Ba M (BaFe 12 O 19 ) with volume fraction of 40,50 and 60 % v/v, coupling agent of the Tetra Isopropyl Titanate in the amount of 5 ml or 10 ml are added before mix turing of the thermoset polymer epoxy or polyester with hexa ferrite powder. The resulting composite were characterized mechanically (tensile strength), hardness and microstructure test. The results showed that the tensile strength and hardness of the composite magnet were increased by increasing the composition of magnetic powder, either Sr M or Ba M, it caused by microstructure of particle Sr M magnetic powder 1.6 μm in the form splinter, where as the Ba M magnetic powder 1,2 μm in nodular form. Thermoset polymer epoxy as binder have tensile strength and hardness is bigger than composite magnet based on polyester, either Sr M or Ba M. The addition of coupling agent is very influenced on the tensile strength and hardness composite magnet, the more coupling magnet addition causes the more tensile strength and hardness of the composite magnet

Hydrothermal synthesis and tunable luminescent properties of Sr{sub 2-x}Dy {sub x}CeO{sub 4} rod-like phosphors derived from co-precipitation precursors

Energy Technology Data Exchange (ETDEWEB)

He Xianghong [School of Chemistry and Chemical Engineering, Jiangsu Teachers' University of Technology, Changzhou, Jiangsu 213001 (China) and Jiangsu Province Key Laboratory of Precious Metal Chemistry and Technology, Changzhou, Jiangsu 213001 (China)]. E-mail: hexh@jstu.edu.cn; Li Weihua [School of Chemistry and Chemical Engineering, Jiangsu Teachers' University of Technology, Changzhou, Jiangsu 213001 (China); Jiangsu Province Key Laboratory of Precious Metal Chemistry and Technology, Changzhou, Jiangsu 213001 (China); Zhou Quanfa [School of Chemistry and Chemical Engineering, Jiangsu Teachers' University of Technology, Changzhou, Jiangsu 213001 (China); Jiangsu Province Key Laboratory of Precious Metal Chemistry and Technology, Changzhou, Jiangsu 213001 (China)

2006-09-25

Uniform rod-like Sr{sub 2-x}Dy {sub x}CeO{sub 4} nano-phosphors with orthorhombic structure were prepared via a hydrothermal method, in the absence of any surfactant or template. The structure, morphology, particle size, and tunable luminescence properties of the samples were investigated by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), UV-vis absorption and photoluminescence spectrum, respectively. The as-prepared phase-pure Sr{sub 2-x}Dy {sub x}CeO{sub 4} nanorods had the length of 50-150 nm and width of 80 nm. The Dy{sup 3+} ions emission in Sr{sub 2-x}Dy {sub x}CeO{sub 4} could be effectively excited through the energy absorbed by Sr{sub 2}CeO{sub 4} host. The tunable photoluminescence has been observed from Sr{sub 2}CeO{sub 4} doped with Dy{sup 3+} ions. Emission color of Sr{sub 2-x}Dy {sub x}CeO{sub 4} phosphor could be regulated from blue-white to white to yellow by adjusting the Dy{sup 3+} doping content in Sr{sub 2}CeO{sub 4} host, which originated from energy transfer between two different emission centers.

Synthesis of Eu{sub x}Si{sub 6-z}Al{sub z}O{sub z}N{sub 8-z} green phosphor and its luminescent properties

Energy Technology Data Exchange (ETDEWEB)

Ryu, Jeong Ho; Won, Hyong Sik; Park, Youn-Gon; Kim, Sang Hyun; Song, Won Young; Suzuki, Hideo; Yoon, Chulsoo [Samsung Electro-Mechanics Co., LTD, Corporate R and D Institute, Suwon, Gyunggi-Do (Korea)

2009-06-15

Rare-earth-doped oxynitride or nitride compounds have been reported to be photoluminescent and may then serve as new phosphors because of their good thermal and chemical stabilities. In this work, Eu{sup 2+}-doped {beta}-SiAlON phosphor with a composition of Eu{sub x}Si{sub 6-z}Al{sub z}O{sub z}N{sub 8-z} (x=0.018,z=0.23) was prepared by gas-pressured solid state reaction. The crystallinity and particle morphology of the prepared phosphor were characterized. The Stokes shift and zero-phonon line were calculated mathematically and estimated from the spectral data. The temperature dependence of photoluminescence was measured from 25 to 250 C. The prepared Eu{sup 2+}-doped {beta}-SiAlON green phosphor showed superior thermal quenching property compared to silicate (SrBaSiO{sub 4}:Eu{sup 2+}) green phosphor. The white light-emitting diode (LED) back-lighting unit (BLU) using the prepared {beta}-SiAlON:Eu{sup 2+} green phosphor exhibited higher color gamut than a commercial silicate phosphor. (orig.)

Diamagnetism to ferromagnetism in Sr-substituted epitaxial BaTiO{sub 3} thin films

Energy Technology Data Exchange (ETDEWEB)

Singamaneni, Srinivasa Rao, E-mail: ssingam@ncsu.edu; Prater, John T. [Materials Science Division, Army Research Office, Research Triangle Park, North Carolina 27709 (United States); Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Punugupati, Sandhyarani; Narayan, Jagdish [Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States)

2016-04-04

We report on the ferromagnetic-like behavior in otherwise diamagnetic BaTiO{sub 3} (BTO) thin films upon doping with non-magnetic element Sr having the composition Ba{sub 0.4}Sr{sub 0.6}TiO{sub 3} (BST). The epitaxial integration of BST (∼800 nm) thick films on Si (100) substrate was achieved using MgO (40 nm) and TiN (20 nm) as buffer layers to prepare BST/MgO/TiN/Si (100) heterostructure by pulsed laser deposition. The c-axis oriented and cube-on-cube epitaxial BST is formed on Si (100) as evidenced by the in-plane and out-of-plane X-ray diffraction. All the deposited films are relaxed through domain matching epitaxy paradigm as observed from X-ray diffraction pattern and A{sub 1}TO{sub 3} mode (at 521.27 cm{sup −1}) of Raman spectra. As-deposited BST thin films reveal ferromagnetic-like properties, which persist up to 400 K. The magnetization decreases two-fold upon oxygen annealing. In contrast, as-deposited un-doped BTO films show diamagnetism. Electron spin resonance measurements reveal no evidence of external magnetic impurities. XRD and X-ray photoelectron spectroscopy spectra show significant changes influenced by Sr doping in BTO. The ferromagnetic-like behavior in BST could be due to the trapped electron donors from oxygen vacancies resulting from Sr-doping.

Theoretical investigation on thermoelectric properties of (Ca,Sr,Ba)Fe2(As/Bi)2 compounds under temperature

Science.gov (United States)

Jayalakshmi, D. S.; Sundareswari, M.; Viswanathan, E.; Das, Abhijeet

2018-04-01

The electrical conductivity, resistivity and Seebeck coefficient, Pauli magnetic susceptibility and power factor are computed under temperature (100 K - 800 K) in steps of 100 K for the theoretically designed compounds namely (Ca,Sr,Ba)Fe2Bi2 and their parent compounds namely (Ca,Sr,Ba)Fe2As2 by using Boltzmann transport theory interfaced to the Wien2k program. The Bulk modulus, electron phonon coupling constant, thermoelectric figure of merit (ZT) and transition temperature are calculated for the optimized anti ferromagnetic phase of the proposed compounds. The results are discussed for the novel compounds in view of their superconductivity existence and compared with their parent unconventional superconducting compounds.

Photoluminescence characterization of Dy3+ and Eu2+ ion in M5(PO4)3F (M = Ba, Sr, Ca) phosphors

International Nuclear Information System (INIS)

Nagpure, I.M.; Shinde, K.N.; Dhoble, S.J.; Kumar, Animesh

2009-01-01

Photoluminescence investigation of Eu and Dy activated phosphate based phosphors prepared by combustion synthesis, characterized by XRD (X-ray diffraction) and photoluminescence techniques, has been reported. PL excitation spectrum of M 5 (PO 4 ) 3 F:Dy phosphors shows the excitation peaks ranging from 300 to 400 nm due to 4f → 4f transitions of Dy 3+ ions. PL emission spectrum of Dy 3+ ion under 348 nm excitation gives PL emission at 482 nm (blue) due to 4 F 9/2 → 6 H 15/2 transitions, 574 nm (yellow) emission due to 4 F 9/2 → 6 H 13/2 transitions and 670 nm (red) due to 4 F 9/2 → 6 H 11/2 transitions, gives BYR (blue-yellow-red) emissions. The Eu 2+ broad band PL emission spectrum was observed in M 5 (PO 4 ) 3 F:Eu phosphor at 440 nm in the blue region of the spectrum due to 5d → 4f transition at 352 nm excitation. The 300-400 nm is Hg-free excitation (Hg excitation is 85% 254 nm wavelength of light and 15% other wavelengths), which is characteristic of solid-state lighting phosphors. Hence PL emission in divalent europium and trivalent dysprosium may be efficient photoluminescent materials for solid-state lighting phosphors.

Lattice mismatch and energy transfer of Eu- and Dy-codoped MO–Al2O3–SrO (M=Mg, Ca, Ba) ternary compounds affecting luminescence behavior

International Nuclear Information System (INIS)

Liang, Chen-Jui; Huang, Kuan-Yu

2017-01-01

A systematic investigation of energy transfers and luminescence behaviors for M x Sr 0.94−x Al 2 O 4 :Eu 0.02 , Dy 0.04 (M=Mg, Ca, Ba; x=0, 0.235, 0.47, 0.705, 0.94) ternary compounds was accomplished. The results demonstrated that six phenomena must be fitted into the energy-transfer mechanisms of the ternary compounds: (1) the optical band-gap energy of Mg 0.94 Al 2 O 4 :Eu 0.02 Dy 0.04 is extremely low and does not allow photoemission; (2) Ca 2+ and Ba 2+ ions are the main hosts when x≥0.47 in Ca x Sr 1−x Al 2 O 4 :Eu 0.02 Dy 0.04 and Ba x Sr 1−x Al 2 O 4 :Eu 0.02 Dy 0.04 , respectively; (3) Eu 3+ ions are the main activator ions in Ca x Sr 1−x Al 2 O 4 :Eu 0.02 Dy 0.04 with x=0.47 and in Ba x Sr 1−x Al 2 O 4 :Eu 0.02 Dy 0.04 with x=0.353−0.705; (4) Sr 2+ and Eu 2+ ions are the main host and activator ions, respectively, when x<0.353 in each ternary compound; (5) energy transfers from the MO phases to the SrO phase because the conduction band energy of SrO is the lowest; and (6) mutual substitution between alkaline-earth ions does not alter the resultant structures’ crystal field and nephelauxetic effects, as determined by measuring their luminescence. Two energy transfer paths were discovered to be possible in CaO–Al 2 O 3 –SrO and BaO–Al 2 O 3 –SrO ternary compounds, and the boundaries determining which path was chosen were the atomic ratios Ca:Sr and Ba:Sr, both approximately 1.6:1 (x=0.353). Because second path increased the energy transferred from the MO band gap to the SrO band gap, the corresponding structure's spectrum emission intensity was approximately 4.3 times higher than that of the SrO−Al 2 O 3 binary compound, and their photoluminescence was thus substantially higher.

Fractal formation of a Y-Ba-Cu-O thin film on SrTiO3

International Nuclear Information System (INIS)

Chow, L.; Chen, J.; Desai, V.; Sundaram, K.; Arora, S.

1989-01-01

Fractal formation has been observed after thermal annealing of the rf-sputtered Y-Ba-Cu-O thin film on SrTiO 3 substrate. Through energy-dispersive x-ray analysis, it was found that the composition of the fractal was YBa 2 Cu 3 O x and the surrounding film composition wasY 2 Ba 2 Cu 3 O x . The fractal dimensions D ranging from 1.26 to 1.65 were obtained using the standard sandbox method with different thresholds

Structure of the new Tl(Ba sub 1.0 Sr sub 1.0) PrCu sub 2 O sub 7-x by Rietveld analysis

International Nuclear Information System (INIS)

Yang, P.; Fun, H. K.; Lee, T.J.; Ku, H.C.; Lai, C.C.

1994-01-01

The crystalline structure of Tl(Ba sub 1.0 Sr sub 1.0)PrCu sub 2 O sub 7-x was obtained at room temperature from x-ray powder diffraction with CuK sub α radiation using Rietveld analysis. Tl(Ba sub 1.0 Sr sub 1.0)PrCu sub 2 O sub 7-x isomorphous at both room temperature (300 K) and low temperature (100 K) with TlBa sub 2 ca Cu sub 2 O sub 7-x type (1212) structure, crystallized with space group P4/mmm and one formula in the unit cell. At 300 K, cell parameters a=3.8892(2) A, c=12.3099(6) A, the structure was refined with 25 parameters to R sub WP = 6.30%, R sub P = 4.38% for 3551 step intensities and R sub b = 5.01%, R sub f = 4.20% for 156 reflections. The goodness of fitting S=3.18. At 100K, cell parameters a=3.8866(4) A, c= 12.289(1) A, the structure was refined with 26 parameters to R sub WP = 8.42%, R sub P = 6.21% for 2676 step intensities and R sub b = 6.72%, R sub f = 5.28% for 120 reflections. The goodness of fitting S=2.32. Reasonable anisotropic thermal parameters were obtained. The compositions of Ba and Sr atoms were refined to about Ba sub 1.1 Sr sub 0.9 compared with the stoichiometric Ba sub 1.0 Sr sub 1.0

Blue photoluminescence and long lasting phosphorescence properties of a novel chloride phosphate phosphor: Sr5(PO4)3Cl:Eu2+

International Nuclear Information System (INIS)

Wu, Chuanqiang; Zhang, Jiachi; Feng, Pengfei; Duan, Yiming; Zhang, Zhiya; Wang, Yuhua

2014-01-01

A novel blue emitting long lasting phosphorescence phosphor Sr 5 (PO 4 ) 3 Cl:Eu 2+ is synthesized by solid state method at 1223 K in reducing atmosphere. The afterglow emission spectrum shows one broad band centered at 441 nm due to the 5d–4f transition of Eu 2+ at six coordinated Sr(II) sites and the color coordinates are calculated to be (0.149, 0.095) which is close to the light blue region. The excitation band is in 240–430 nm and partly overlaps the solar irradiation on Earth's surface. The long lasting phosphorescence of the optimal sample doping by 0.1 mol%Eu 2+ can be recorded for about 1040 s (0.32 mcd/m 2 ). Thermoluminescence shows that there are at least three types of traps corresponding to peaks at 340 K, 382 K, 500 K, respectively. The filling and fading experiments reveal that the traps in Sr 5 (PO 4 ) 3 Cl:Eu 2+ are independent. The shallow traps (340 K) essentially contribute to the visible long lasting phosphorescence, while the deep traps (382 K and 500 K) are proved to be very stable. Thus, the Sr 5 (PO 4 ) 3 Cl:Eu 2+ material shows potential applications as not only a long lasting phosphorescence phosphor, but also an optical storage material. -- Highlights: • The blue long lasting phosphorescence of Sr 5 (PO 4 ) 3 Cl:Eu 2+ is first reported. • Filling and fading experiments are carried out for revealing natures of traps. • The afterglow mechanism for independent traps of Sr 5 (PO 4 ) 3 Cl:Eu 2+ is proposed

(Sr,Ba)(Si,Ge)2 for thin-film solar-cell applications: First-principles study

International Nuclear Information System (INIS)

Kumar, Mukesh; Umezawa, Naoto; Imai, Motoharu

2014-01-01

In order to meet the increasing demand for electric power generation from solar energy conversion, the development of efficient light absorber materials has been awaited. To this end, the electronic and optical properties of advanced alkaline-earth-metals disilicides and digermanides (SrSi 2 , BaSi 2 , SrGe 2 , and BaGe 2 ) are studied by means of the density functional theory using HSE06 exchange-correlation energy functional. Our calculations show that all these orthorhombic structured compounds have fundamental indirect band gaps in the range E g ≈ 0.89–1.25 eV, which is suitable for solar cell applications. The estimated lattice parameters and band gaps are in good agreement with experiments. Our calculations show that the electronic band structures of all four compounds are very similar except in the vicinity of the Γ-point. The valence band of these compounds is made up by Si(Ge)-p states, whereas the conduction band is composed of Sr(Ba)-d states. Their band alignments are carefully determined by estimating the work function of each compound using slab model. The optical properties are discussed in terms of the complex dielectric function ε(ω) = ε 1 (ω) + iε 2 (ω). The static and high-frequency dielectric constants are calculated, taking into account the ionic contribution. The absorption coefficient α(ω) demonstrates that a low energy dispersion of the conduction band, which results in a flat conduction band minimum, leads to large optical activity in these compounds. Therefore, alkaline-earth-metals disilicides and digermanides possess great potential as light absorbers for applications in thin-film solar cell technologies.

Influence of bismuth on properties and microstructures of Sr0⋅ 5Ba0 ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 29; Issue 5. Influence of bismuth on properties and microstructures of Sr0.5Ba0.5–Bi TiO3 thin films. Tao Wenhong Wang Yin Fu Xinghua Wei Qihong. Thin Films Volume 29 Issue 5 October 2006 pp 523-527 ...

Enhancing the Photocatalytic Activity of Sr4 Al14 O25 : Eu2+ , Dy3+ Persistent Phosphors by Codoping with Bi3+ Ions.

Science.gov (United States)

García, Carlos R; Oliva, Jorge; Romero, Maria Teresa; Diaz-Torres, Luis A

2016-03-01

The photocatalytic activity of Bismuth-codoped Sr 4 Al 14 O 25 : Eu 2+ , Dy 3+ persistent phosphors is studied by monitoring the degradation of the blue methylene dye UV light irradiation. Powder phosphors are obtained by a combustion synthesis method and a postannealing process in reductive atmosphere. The XRD patterns show a single orthorhombic phase Sr 4 Al 14 O 25 : Eu 2+ , Dy 3+ , Bi 3+ phosphors even at high Bismuth dopant concentrations of 12 mol%, suggesting that Bi ions are well incorporated into the host lattice. SEM micrographs show irregular micrograins with sizes in the range of 0.5-20 μm. The samples present an intense greenish-blue fluorescence and persistent emissions at 495 nm, attributed to the 5d-4f allowed transitions of Eu 2+ . The fluorescence decreases as Bi concentration increases; that suggest bismuth-induced traps formation that in turn quench the luminescence. The photocatalytic evaluation of the powders was studied under both 365 nm UV and solar irradiations. Sample with 12 mol% of Bi presented the best MB degradation activity; 310 min of solar irradiation allow 100% MB degradation, whereas only 62.49% MB degradation is achieved under UV irradiation. Our results suggest that codoping the persistent phosphors with Bi 3+ can be an alternative to enhance their photocatalytic activity. © 2016 The American Society of Photobiology.

Emergence of the sub-THz central peak at phase transitions in artificial BaTiO3/(Ba,Sr)TiO3 superlattices

International Nuclear Information System (INIS)

Tikhonov, Yu.A.; Razumnaya, A.G.; Torgashev, V.I.; Zakharchenko, I.N.; Yuzyuk, Yu.I.; El Marssi, M.; Ortega, N.; Kumar, A.; Katiyar, R.S.

2015-01-01

A prominent central peak in the sub-THz frequency range was observed in the Raman spectra of BaTiO 3 /(Ba,Sr)TiO 3 (BT/BST) superlattice grown on (001)MgO substrate. Both soft and central mode show an anomaly around 200 K and 280 K, which can be correlated with orthorhombic to monoclinic phase transition of BST and BT, respectively. The observed temperature dependence of the central mode enabled us to explain rather broad temperature dependence of the dielectric permittivity previously observed in BT/BST superlattices. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Study of formation of deep trapping mechanism by UV, beta and gamma irradiated Eu(3+) activated SrY2O4 and Y4Al2O9 phosphors.

Science.gov (United States)

Dubey, Vikas; Kaur, Jagjeet; Parganiha, Yogita; Suryanarayana, N S; Murthy, K V R

2016-04-01

This paper reports the thermoluminescence properties of Eu(3+) doped different host matrix phosphors (SrY2O4 and Y4Al2O9). The phosphor is prepared by high temperature solid state reaction method. The method is suitable for large scale production and fixed concentration of boric acid using as a flux. The prepared samples were characterized by X-ray diffraction technique and the crystallite size calculated by Scherer's formula. The prepared phosphor characterized by Scanning Electron Microscopic (SEM), Fourier Transform Infrared (FTIR), Energy Dispersive X-ray analysis (EDX), thermoluminescence (TL) and Transmission Electron Microscopic (TEM) techniques. The prepared phosphors for different concentration of Eu(3+) ions were examined by TL glow curve for UV, beta and gamma irradiation. The UV 254nm source used for UV irradiation, Sr(90) source was used for beta irradiation and Co(60) source used for gamma irradiation. SrY2O4:Eu(3+)and Y4Al2O9:Eu(3+) phosphors which shows both higher temperature peaks and lower temperature peaks for UV, beta and gamma irradiation. Here UV irradiated sample shows the formation of shallow trap (surface trapping) and the gamma irradiated sample shows the formation of deep trapping. The estimation of trap formation was evaluated by knowledge of trapping parameters. The trapping parameters such as activation energy, order of kinetics and frequency factor were calculated by peak shape method. Here most of the peak shows second order of kinetics. The effect of gamma, beta and UV exposure on TL studies was also examined and it shows linear response with dose which indicate that the samples may be useful for TL dosimetry. Formation of deep trapping mechanism by UV, beta and gamma irradiated Eu(3+) activated SrY2O4 and Y4Al2O9 phosphors is discussed in this paper. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimizing Blue Persistent Luminescence in (Sr _1-δ Ba _δ ) ₂ MgSi ₂ O _7: Eu ²⁺ ,Dy ³⁺ via Solid Solution for Use in Point-of-Care Diagnostics

Energy Technology Data Exchange (ETDEWEB)

Finley, Erin; Cobb, Angelica; Duke, Anna; Paterson, Andrew; Brgoch, Jakoah (Luminostics); (Houston)

2016-11-04

Inorganic persistent luminescent phosphors are an excellent class of optical reporters for enabling sensitive point-of-care diagnostics, particularly with smartphone-based biosensing devices in testing formats such as the lateral flow assay (LFA). Here, the development of persistent phosphors for this application is focused on the solid solution (Sr_1-δBa_δ)₂MgSi₂O₇:Eu²+,Dy³⁺ (δ = 0, 0.125, 0.25, 0.375), which is prepared using a high-temperature solid-state reaction as confirmed by synchrotron X-ray powder diffraction. The substitution of barium for strontium enables control over the Eu²⁺ 5d-orbital crystal field splitting (CFS) as a tool for tuning the emission wavelength while maintaining luminescence lifetimes >9 min across the composition range. Thermoluminescence measurements of the solid solution provide evidence that trap states contribute to the persistent lifetimes with the trap depths also remaining constant as a function of composition. Time-gated luminescence images of these compounds are captured on a smartphone arranged in a layout to mimic a point-of-care test and demonstrate the viability of using these materials as optical reporters. Moreover, comparing the blue-emitting (Sr_0.625Ba_0.375)₂MgSi₂O₇:Eu²⁺,Dy³⁺ and the green-emitting SrAl₂O_4:Eu²⁺,Dy³⁺ in a single LFA-type format shows these two compounds can be detected and resolved simultaneously, thereby permitting the development of a multiplexed LFA.

SiO{sub 2} effect on spectral and colorimetric properties of europium doped SrO{sub 2}-MgO-xSiO{sub 2} (0.8 {<=} x {<=} 1.6) phosphor for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Chen, B J; Jang, K W; Lee, H S; Jayasimhadri, M; Cho, E J [Department of Physics, Changwon National University, Changwon, 641-773 (Korea, Republic of); Yi, S S [Department of Photonics, Silla University, Pusan 617-736 (Korea, Republic of); Jeong, J H [Department of Physics, Pukyong National University, Pusan 608-737 (Korea, Republic of)], E-mail: kwjang@changwon.ac.kr

2009-05-21

Silicate phosphors with compositions 1.99 SrO{sub 2}-1.0 MgO-xSiO{sub 2}-0.01 Eu{sub 2}O{sub 3} (x = 0.8, 1.0, 1.2, 1.4 and 1.6) were prepared in a reducing atmosphere via a solid state reaction. The resultant phosphors were examined by using x-ray diffraction and confirmed to be a mixture of monoclinic Sr{sub 2}SiO{sub 4} and orthorhombic Mg{sub 2}(Si{sub 2}O{sub 4}). The scanning electron microscope images revealed that SiO{sub 2} content does not influence the morphology of the resultant phosphors. It was also observed that the excitation spectra are dependent on the monitored emission wavelength, and the emission spectra are dependent on the excitation wavelength and the SiO{sub 2} content. The energy transfer between Eu{sup 2+} ions occupying different Sr{sup 2+} sites was discussed. The colour coordinates for these phosphors are tunable based on both the excitation wavelength and the SiO{sub 2} content.

Luminescent processes in SrAl2O4: Eu2+, Dy3+ phosphors exposed to ultraviolet radiation

International Nuclear Information System (INIS)

Arellano T, O.; Castaneda, B.; Pedroza M, M.; Melendrez, R.; Chernov, V.; Barboza F, M.; Yen, W.M.

2006-01-01

The long persistent response of the SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphors has been utilized in the development of new luminescent devices with low voltage requirements, incorporated in luminous paints and emergency light illumination. We have studied the experimental characteristics of thermoluminescence (TL) and afterglow (AG) processes in UV irradiated long persistent phosphors SrAl 2 O 4 : Eu 2+ , Dy 3+ . The TL signal is achieved by thermal stimulation of material and it involves the release of trapped charge carriers in the form of electrons and/or electrons and holes generated by irradiation exposure of the dosimetric materials, while the AG signal is obtained at RT without thermal stimulation. In both cases, the intensity of the response is proportional to the radiation dose. For our UV irradiated SrAl 2 O 4 : Eu 2+ , Dy 3+ samples, the TL glow curve depicted at least five peaks around 318, 424, 457, 488 and 515 K with activation energy values of 0.28, 0.67, 1.00, 1.35 and 1.62 eV, respectively. In this respect, the initial rise method was used to estimate experimentally the peak positions. Then, these experimental data were used as initial values to determine the kinetics parameters through a computer deconvolution and fitting process. Besides, the AG response was analyzed and we found it has at least three exponential processes with different lifetimes around 56, 180 and 1230 s, respectively. In addition, the afterglow dosimetry performance of this SrAl 2 O 4 : Eu 2+ , Dy 3+ phosphor exhibited a linear behavior for the first fifty seconds of ultraviolet irradiation. For higher ultraviolet time exposure the behavior is sub linear with no apparent saturation during ten minutes. The afterglow dosimetry response was performed with a source of 400 nm that corresponds to the main band component of the afterglow excitation spectrum in the 250-500 nm range. The TL glow intensity peaked at 460 K and AG intensity responses are strongly dependents on the excitation

Fabrication and characterization of Ba sub x Sr sub 1 sub - sub x TiO sub 3 /YBa sub 2 Cu sub 3 O sub x /SrTiO sub 3 structure

CERN Document Server

Choi, J; Park, S Y; Lee Jae Sik; No, K; Sung, T H; Park, Y

2002-01-01

Ba sub x Sr sub 1 sub - sub x TiO sub 3 (BST)/YBa sub 2 Cu sub 3 O sub x (YBCO)/SrTiO sub 3 (STO) structures were deposited, and the microstructure, orientation and electrical characteristics were investigated. (00l) oriented YBCO thin films were deposited on STO substrates using pulsed laser deposition, and (h00) oriented BST thin films were deposited on YBCO/STO substrates using electron cyclotron resonance (ECR) plasma assisted metal organic chemical vapor deposition (MOCVD). A new phase was formed at the interface between YBCO and BST films and was speculated to be (Ba sub x Y sub 1 sub - sub x)(Ti sub y Y sub 1 sub - sub y)O sub 3. Ba-rich BST films showed a higher dielectric loss than Sr-rich BST films did, which indicates that Sr-rich BST films are more suited for application to microwave devices. The dielectric loss of the films was reduced as temperature decreased, which may be due to the conductivity change of YBCO film and the formation of a conduction path rather than a dielectric property change ...

Enhance luminescence by introducing alkali metal ions (R+ = Li+, Na+ and K+) in SrAl2O4:Eu3+ phosphor by solid-state reaction method

Science.gov (United States)

Prasad Sahu, Ishwar

2016-05-01

In the present article, the role of charge compensator ions (R+ = Li+, Na+ and K+) in europium-doped strontium aluminate (SrAl2O4:Eu3+) phosphors was synthesized by the high-temperature, solid-state reaction method. The crystal structures of sintered phosphors were in a monoclinic phase with space group P21. The trap parameters which are mainly activation energy (E), frequency factor (s) and order of the kinetics (b) were evaluated by using the peak shape method. The calculated trap depths are in the range from 0.76 to 0.84 eV. Photoluminescence measurements showed that the phosphor exhibited emission peak with good intensity at 595 nm, corresponding to 5D0-7F1 (514 nm) orange emission and weak 5D0-7F2 (614 nm) red emission. The excitation spectra monitored at 595 nm show a broad band from 220 to 320 nm ascribed to O-Eu charge-transfer state transition and the other peaks in the range of 350-500 nm originated from f-f transitions of Eu3+ ions. The strongest band at 394 nm can be assigned to 7F0-5L6 transition of Eu3+ ions due to the typical f-f transitions within Eu3+ of 4f6 configuration. The latter lies in near ultraviolet (350-500 nm) emission of UV LED. CIE color chromaticity diagram and thermoluminescence spectra confirm that the synthesized phosphors would emit an orange-red color. Incorporating R+ = Li+, Na+ and K+ as the compensator charge, the emission intensity of SrAl2O4:Eu3+ phosphor can be obviously enhanced and the emission intensity of SrAl2O4:Eu3+ doping Li+ is higher than that of Na+ or K+ ions.

Comparative study of the ionic exchange of Ca++, Sr++, and Ba++ cations on resins and inorganic exchangers

International Nuclear Information System (INIS)

Sanchez Batanero, P.

1969-03-01

With a view to applying the results to certain problems related to chemical separations in activation analysis, a study has been made, of the possibilities of separating the alkaline-earth elements Ca, Sr and Ba on organic resins and inorganic exchangers using the radioactive indicator method. The partition coefficients of the cations Ca 2+ , Sr 2+ and Ba 2+ have been measured on Dowex 50 W (NH 4 + ) x 8 resin in the presence of EDTA - NTA - EGTA and DCTA as complexing agents, and on zirconium phosphate, tungstate and molybdate in the presence of HCl and NH 4 Cl. Methods have been developed for separating mixtures of alkaline-earth elements using DCTA-NH 4 + followed by elution on Dowex 50 W (NH 4 + ) x 8 resin columns and on zirconium phosphate. Amongst the complexing agents used on the ion-exchange resins the most promising appears to be DCTA which leads to partition coefficients Ca, Sr and Ba which are very different. The results of measurements of partition coefficients on zirconium phosphate (NH 4 + form) using DCTA-NH 4 + show the interesting possibilities of separations on columns. The separation of the alkaline-earth elements on zirconium phosphate seems to be less quantitative than on Dowex 50 resin; it is however much faster in the former case and this can be useful for treating short half-life radioisotopes in activation analysis. (author) [fr

Luminescence investigations of rare earth doped lead-free borate glasses modified by MO (M = Ca, Sr, Ba)

Energy Technology Data Exchange (ETDEWEB)

Janek, Joanna, E-mail: janek.joanna@gmail.com; Sołtys, Marta; Żur, Lidia; Pietrasik, Ewa; Pisarska, Joanna; Pisarski, Wojciech A.

2016-09-01

Series of lead-free borate glasses with different oxide modifiers and lanthanide ions were prepared. The effect of oxide modifiers MO (M = Ca, Sr, Ba) on spectroscopic properties of trivalent Ln{sup 3+} (Ln = Eu, Er, Pr) were systematically investigated. Especially, the luminescence spectra of Ln{sup 3+}-doped lead-free borate glasses are presented and discussed in relation to the impact of selective components (CaO, SrO and BaO). Several spectroscopic parameters, such as the fluorescence intensity ratio R/O (Eu{sup 3+}) and measured luminescence lifetimes for the {sup 5}D{sub 0} (Eu{sup 3+}), {sup 4}I{sub 13/2} (Er{sup 3+}) and {sup 1}D{sub 2} (Pr{sup 3+}) excited states of lanthanide ions were analyzed in details. The research proved that spectroscopic properties of trivalent Ln{sup 3+} depend significantly on kind of presence oxide modifiers MO (M = Ca, Sr, Ba) in glass host matrices. - Highlights: • Luminescence of Ln{sup 3+}-doped borate glasses was presented and discussed. • Effect of glass modifiers on spectroscopic properties of rare earths was studied. • Measured luminescence lifetimes of Ln{sup 3+} (Ln = Eu, Er, Pr) were analyzed. • Luminescence intensity ratios R/O (Eu{sup 3+}) were determined.

Comparative study of the ionic exchange of Ca{sup ++}, Sr{sup ++}, and Ba{sup ++} cations on resins and inorganic exchangers; Etude comparative de l'echange ionique des cations Ca{sup ++}, Sr{sup ++} et Ba{sup ++} sur resine et sur echangeurs mineraux

Energy Technology Data Exchange (ETDEWEB)

Sanchez Batanero, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1969-03-01

With a view to applying the results to certain problems related to chemical separations in activation analysis, a study has been made, of the possibilities of separating the alkaline-earth elements Ca, Sr and Ba on organic resins and inorganic exchangers using the radioactive indicator method. The partition coefficients of the cations Ca{sup 2+}, Sr{sup 2+} and Ba{sup 2+} have been measured on Dowex 50 W (NH{sub 4}{sup +}) x 8 resin in the presence of EDTA - NTA - EGTA and DCTA as complexing agents, and on zirconium phosphate, tungstate and molybdate in the presence of HCl and NH{sub 4}Cl. Methods have been developed for separating mixtures of alkaline-earth elements using DCTA-NH{sub 4}{sup +} followed by elution on Dowex 50 W (NH{sub 4}{sup +}) x 8 resin columns and on zirconium phosphate. Amongst the complexing agents used on the ion-exchange resins the most promising appears to be DCTA which leads to partition coefficients Ca, Sr and Ba which are very different. The results of measurements of partition coefficients on zirconium phosphate (NH{sub 4}{sup +} form) using DCTA-NH{sub 4}{sup +} show the interesting possibilities of separations on columns. The separation of the alkaline-earth elements on zirconium phosphate seems to be less quantitative than on Dowex 50 resin; it is however much faster in the former case and this can be useful for treating short half-life radioisotopes in activation analysis. (author) [French] En vue de l'application a certains problemes de separations chimiques en analyse par activation, on a etudie les possibilites de separation des elements alcalino-terreux Ca-Sr et Ba sur resine organique et sur echangeurs mineraux par la methode des indicateurs radioactifs. Les coefficients de partage des cations Ca{sup +2}, Sr{sup +2} et Ba{sup +2} sur resine Dowex 50 W (NH{sub 4}{sup +}) x 8 en milieux complexants EDTA - NTA - EGTA et DCTA et sur phosphate, tungstate et molybdate de zirconium en milieu HCl et NH{sub 4}Cl ont ete mesures. Des

Effect of Sr substitution on superconductivity in Hg2(Ba1-ySry)2YCu2O8-d (part 1): a neutron powder diffraction study

OpenAIRE

Toulemonde, P.; Odier, P.; Bordet, P.; Floch, S. Le; Suard, E.

2002-01-01

The effect of Sr chemical pressure on superconductivity was investigated in Hg2(Ba1-ySry)2YCu2O8-d. The samples were synthesized at high pressure-high temperature from y = 0.0 to full substitution, y = 1.0. These Sr-substituted compounds are superconducting, without Ca doping on the Y site, and show an increasing Tc with Sr, reaching 42 K for y = 1.0. A detailed neutron powder diffraction study compares the structural changes induced by this chemical Sr/Ba substitution and the mechanical pres...

Enhanced luminescent properties of long-persistent Sr{sub 2}MgSi{sub 2}O{sub 7}:Eu{sup 2+}, Dy{sup 3+} phosphor prepared by the co-precipitation method

Energy Technology Data Exchange (ETDEWEB)

Pan Wen [State Key Laboratory of Fine Chemicals, Department of Materials Science and Chemical Engineering, School of Chemical Engineering, Dalian University of Technology, Zhongshan Road 158-43, Dalian Liaoning 116012 (China); Ning Guiling [State Key Laboratory of Fine Chemicals, Department of Materials Science and Chemical Engineering, School of Chemical Engineering, Dalian University of Technology, Zhongshan Road 158-43, Dalian Liaoning 116012 (China)], E-mail: ninggl@dlut.edu.cn; Zhang Xu; Wang Jing; Lin Yuan; Ye Junwei [State Key Laboratory of Fine Chemicals, Department of Materials Science and Chemical Engineering, School of Chemical Engineering, Dalian University of Technology, Zhongshan Road 158-43, Dalian Liaoning 116012 (China)

2008-12-15

Sr{sub 2}MgSi{sub 2}O{sub 7}:Eu{sup 2+}, Dy{sup 3+} phosphors were prepared by the (aminopropyl)-triethoxysilane (APTES) co-precipitation method. Effects of synthesis temperature on the crystal characteristics, luminescent properties and afterglow performance of Sr{sub 2}MgSi{sub 2}O{sub 7}:Eu{sup 2+}, Dy{sup 3+} phosphors have been discussed in detail and compared with the corresponding commercial product. The experimental results indicated that the sample could be synthesized at a relatively lower temperature and had better performance on the above-mentioned properties using the co-precipitation method.

Unactivated yttrium tantalate phosphor

International Nuclear Information System (INIS)

Reddy, V.B.; Cheung, H.K.

1992-01-01

This patent describes an unactivated yttrium tantalate phosphor having M prime monoclinic structure and containing one or more additives of Rb and Al in an amount of between about 0.001 to 0.1 moles per mole of yttrium tantalate to improve brightness under X-radiation. This patent also describes an unactivated yttrium tantalate phosphor having M prime monoclinic structure and containing additives of Sr in an amount of between 0.001 to 0.1 moles per mole of yttrium tantalate and one or more of Rb and Al in an amount of between 0.001 to 0.1 moles per mole of yttrium tantalate the phosphor exhibiting a greater brightness under X-radiation than the phosphor absent Rb and Al

Ab initio hybrid DFT calculations of BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces

Energy Technology Data Exchange (ETDEWEB)

Eglitis, Roberts I., E-mail: rieglitis@gmail.com

2015-12-15

Highlights: • Surface energies for AO{sub 3}-term (111) surfaces are larger than for Ti (Zr)-term surfaces. • A increase of Ti−O (Zr−O) bond covalency near the ABO{sub 3} (111) surface relative to the bulk is observed. • The ABO{sub 3} (111) surface energy is larger than the earlier calculated (001) surface energy. • Band gap for PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces becomes smaller, but for BaTiO{sub 3} (111) larger with respect to the bulk . - Abstract: The results of ab initio calculations for polar BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces using the CRYSTAL code are presented. By means of the hybrid B3LYP approach, the surface relaxation has been calculated for two possible B (B = Ti or Zr) or AO{sub 3} (A = Ba, Pb or Sr) BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surface terminations. According to performed B3LYP calculations, all atoms of the first surface layer, for both terminations, relax inwards. The only exception is a small outward relaxation of the PbO{sub 3}-terminated PbTiO{sub 3} (111) surface upper layer Pb atom. B3LYP calculated surface energies for BaO{sub 3}, PbO{sub 3}, SrO{sub 3} and PbO{sub 3}-terminated BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces are considerably larger than the surface energies for Ti (Zr)-terminated (111) surfaces. Performed B3LYP calculations indicate a considerable increase of Ti−O (Zr−O) chemical bond covalency near the BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surface relative to the BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} bulk. Calculated band gaps at the Γ-point near the PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces are reduced, but near BaTiO{sub 3} (111) surfaces increased, with respect to the BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} bulk band gap at the Γ-point values.

Mn"4"+-activated BaSiF_6 red phosphor: Hydrothermal synthesis and dependence of its luminescent properties on reaction conditions

International Nuclear Information System (INIS)

Zhou, Qiang; Zhou, Yayun; Lu, Fengqi; Liu, Yong; Wang, Qin; Luo, Lijun; Wang, Zhengliang

2016-01-01

In this work, a series of BaSiF_6:Mn"4"+ red phosphors were synthesized through a hydrothermal route. The crystal structure and morphology were characterized by powder X-ray diffraction (XRD) with Rietveld refinement, scanning electron microscopy (SEM), and energy dispersive spectrometer (EDS) in detail. The influence of reaction conditions, including the concentration of KMnO_4 and HF, reaction temperature and time, on the photoluminescence properties were investigated systematically. It can emit intense red light (∼636 nm) under blue light (∼458 nm) illumination. The white LED device based on YAG:Ce–BaSiF_6:Mn"4"+ mixture shows warm white light with low color temperature and high correlated color index, which reveals its potential application in WLED. - Highlights: • The crystal structure of BaSiF_6:Mn"4"+ has been verified using Rietveld refinement. • The optimum hydrothermal reaction condition for BaSiF_6:Mn"4"+ has been confirmed. • The white LED based on YAG:Ce–BaSiF_6:Mn"4"+ mixture presents warmer white light than that only with YAG:Ce.

Effects of La{sub 2}O{sub 3}-doping and sintering temperature on the dielectric properties of BaSrTiO{sub 3} ceramics

Energy Technology Data Exchange (ETDEWEB)

Zhao, Hong Wei; Chang, Chun Rui [College of Science, North China University of Science and Technology, Hebei Province (China); Li, Yuan Liang [Hebei Provincial Key Laboratory of Inorganic Nonmetallic Materials, North China University of Science and Technology, Hebei Province (China); Yan, Chun Liang [Analysis and Testing Center, North China University of Science and Technology, Hebei Province (China)

2016-03-15

Using BaCO{sub 3}, SrCO{sub 3} and TiO{sub 2}, et al as crude materials, La{sub 2}O{sub 3} as dopant, Ba{sub 0.8}Sr{sub 0.2}TiO{sub 3} (BST) Ceramics of perovskite structure were prepared by solid state reaction method. We investigated the effects of La{sub 2}O{sub 3} -doping and sintering temperature on the dielectric properties of BaSrTiO{sub 3} ceramics. The experiment results show that: The amount of La{sub 2}O{sub 3} can increase the dielectric constant of the sample, with the doping amount increasing, the dielectric constant increases. The sintering temperature has also significant impact on the dielectric properties. The dielectric constant of the sample reaches its highest point at 1280 °C. (author)

Effect of oxygen gas and annealing treatment for magnetically enhanced reactive ion etched (Ba0.65,Sr0.35)TiO3 thin films

International Nuclear Information System (INIS)

Zhang Baishun; Quan Zuci; Zhang Tianjin; Guo Tao; Mo Shaobo

2007-01-01

Sol-gel-derived (Ba 0.65 ,Sr 0.35 )TiO 3 (BST) thin films were etched in CF 4 /Ar and CF 4 /Ar/O 2 plasmas using magnetically enhanced reactive ion etching technology. Experimental results show that adding appropriate O 2 to CF 4 /Ar can better the etching effects of BST films for the increase of etching rate and decrease of etched residues. The maximum etching rate is 8.47 nm/min when CF 4 /Ar/O 2 gas-mixing ratio is equal to 9/36/5. X-ray photoelectron spectroscopy (XPS) data confirm accumulation of reaction products on the etched surface due to low volatility of reaction products such as Ba and Sr fluorides, and these residues could be removed by annealing treatment. The exact peak positions and chemical shifts of the interested elements were deduced by fitting XPS narrow-scan spectra with symmetrical Gaussian-Lorentzian product function for Ba 3d, Sr 3d, and O 1s peaks, meanwhile asymmetrical Gaussian-Lorentzian sum function was used to fit Ti 2p doublet to adjust the multiple splitting and/or shake-up process of transition-metal Ti cations. Compared to the unetched counterparts, the etched Ba 3d 5/2 , Ba 3d 3/2 , Sr 3d 5/2 , Sr 3d 3/2 , Ti 2p 3/2 , Ti 2p 1/2 , and O 1s peaks shift towards higher binding energy regions by amounts of 1.31, 1.30, 0.60, 0.79, 0.09, 0.46, and 0.50 eV, respectively. While the etched Ti 2p 3/2 and Ti 2p 1/2 peaks have small chemical shifts for two reasons. One is that Ti fluoride (TiF z ) is mostly removed from the etched surface because of its higher volatility in the process of thermal desorption. The other is that there is a shift compensation between TiF z and the etched BST matrix in which Ti 4+ cations are partially reduced to form Ti x+ (0 0.65 ,Sr 0.35 )Ti 0.97 O 2.86 , (Ba 0.70 ,Sr 0.30 )Ti 0.24 O 1.39 , and (Ba 0.68 ,Sr 0.32 )Ti 0.95 O 2.74 , and then the average valence of Ti cations is estimated to be +3.84, +3.25, and +3.66 with respect to the electroneutrality principle, respectively. It is inferred that electrical

Multi-proxy Reconstructions of the Eastern Equatorial Pacific: Measuring Sr/Ca, Ba/Ca, and Li/Mg in Modern Corals Using ICP-OES

Science.gov (United States)

Cheung, A. H.; Cole, J. E.; Vetter, L.; Jimenez, G.; Thompson, D. M.; Tudhope, A. W.

2017-12-01

Sea surface temperature (SST) in the Eastern Equatorial Pacific (EEP) exhibits large variability on multiple timescales. These variations are often related to modes of climate variability that exert significant influence on global climate, such as the El Niño Southern Oscillation. However, the short length and sparsity of instrumental data in the EEP limits our ability to discern changes in this region. Geochemical signals in corals can help extend instrumental data further back in time. While δ18O and Sr/Ca are the most commonly analyzed geochemical tracers of SST in corals, they often have site-specific complications. Several alternatives (e.g., Li/Mg) have been proposed to overcome these challenges, but have yet to be applied to long climate records, in part due to the cost and time required to measure these elements. Here, we develop a new method that uses Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES) to analyze Li/Mg, Sr/Ca, and Ba/Ca ratios in coral aragonite. We apply this method to two Porites spp. corals collected from the northern Galapagos archipelago (Wolf and Darwin Islands). We specifically assess the fidelity of Li/Mg and Sr/Ca to reconstruct SST, and Ba/Ca to reconstruct upwelling conditions. Our results confirm that both Li/Mg and Sr/Ca track SST. We show that despite analytical noise, downcore reconstructions of Li/Mg have the potential to provide additional information about SST that is not present in reconstructions generated from Sr/Ca alone. Skeletal Ba/Ca shows little relationship with upwelling, perhaps because of the distance of our sites from the center of upwelling in the southern Galapagos. These results demonstrate the potential for analyzing Sr, Li, Ba, Mg simultaneously in corals with a cost- and time- efficient method, which may be applied to coral paleoclimate sites worldwide.

Structure evolution upon chemical and physical pressure in (Sr{sub 1−x}Ba{sub x}){sub 2}FeSbO{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Tiittanen, T.; Karppinen, M., E-mail: maarit.karppinen@aalto.fi

2017-02-15

Here we demonstrate the gradual structural transformation from the monoclinic I2/m to tetragonal I4/m, cubic Fm-3m and hexagonal P6{sub 3}/mmc structure upon the isovalent larger-for-smaller A-site cation substitution in the B-site ordered double-perovskite system (Sr{sub 1−x}Ba{sub x}){sub 2}FeSbO{sub 6}. This is the same transformation sequence previously observed up to Fm-3m upon heating the parent Sr{sub 2}FeSbO{sub 6} phase to high temperatures. High-pressure treatment, on the other hand, transforms the hexagonal P6{sub 3}/mmc structure of the other end member Ba{sub 2}FeSbO{sub 6} back to the cubic Fm-3m structure. Hence we may conclude that chemical pressure, physical pressure and decreasing temperature all work towards the same direction in the (Sr{sub 1−x}Ba{sub x}){sub 2}FeSbO{sub 6} system. Also shown is that with increasing Ba-for-Sr substitution level, i.e. with decreasing chemical pressure effect, the degree-of-order among the B-site cations, Fe and Sb, decreases. - Graphical abstract: In the (Sr{sub 1−x}Ba{sub x}){sub 2}FeSbO{sub 6} double-perovskite system the gradual structural transformation from the monoclinic I2/m to tetragonal I4/m, cubic Fm-3m and hexagonal P6{sub 3}/mmc structure is seen upon the isovalent larger-for-smaller A-site cation substitution. High-pressure treatment under 4 GPa extends stability of the cubic Fm-3m structure within a wider substitution range of x. - Highlights: • Gradual structural transitions upon A-cation substitution in (Sr{sub 1−x}Ba{sub x}){sub 2}FeSbO{sub 6.} • With increasing x structure changes from I2/m to I4/m, Fm-3m and P6{sub 3}/mmc. • Degree of B-site order decreases with increasing x and A-site cation radius. • High-pressure treatment extends cubic Fm-3m phase stability for wider x range. • High-pressure treatment affects bond lengths mostly around the A-cation.

Effects of Sr-substitution on the structural and magnetic behavior of Ba-based Y-type hexagonal ferrites

International Nuclear Information System (INIS)

Ahmad, Mukhtar; Ali, Qasim; Ali, Ihsan; Ahmad, Ishtiaq; Azhar Khan, M.; Akhtar, Majid Niaz; Murtaza, G.; Rana, M.U.

2013-01-01

Highlights: •Sr-substituted Y-type hexaferrites synthesized by sol–gel method have been investigated. •Platelet grains with well defined hexagonal shape are suitable for microwave absorbers. •Saturation magnetization values were calculated by the law of approach to saturation. •Coercivity of a few hundred oersteds found for all samples is suitable for EM materials. -- Abstract: Sr-substituted samples of Y-type hexagonal ferrites with chemical formula Ba 2−x Sr x Ni 2 Fe 12 O 22 (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) were synthesized using the sol–gel autocombustion method and were sintered at 1150 °C for 3 h. The samples were investigated by differential thermal and thermogravimetry analysis, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and vibrating sample magnetometry. X-ray diffraction analysis reveals that single phase samples can be achieved by substituting Sr 2+ ions at Ba 2+ sites in Y-type hexagonal ferrites. X-ray density and bulk density were observed to decrease whereas porosity increased with increasing Sr-concentration. All the samples show well defined hexagonal shape which is favorable for microwave absorbing purposes. The saturation magnetization values were calculated from M–H loops by the law of approach to saturation. The loops show low values of coercivity of a few hundred oersteds which is one of the necessary conditions for electromagnetic (EM) materials and is suitable for security, switching, sensing and high frequency applications

Magnetic and magneto-transport properties of double perovskite Ba{sub 2-x}Sr{sub x}FeMoO{sub 6} system

Energy Technology Data Exchange (ETDEWEB)

Pandey, Vibhav; Verma, Vivek; Aloysius, R.P. [National Physical Laboratory, Dr. K.S. Krishnan Marg, New Delhi-110012 (India); Bhalla, G.L. [Department of Physics and Astrophysics, Delhi University, Delhi (India); Awana, V.P.S.; Kishan, H. [National Physical Laboratory, Dr. K.S. Krishnan Marg, New Delhi-110012 (India); Kotnala, R.K. [National Physical Laboratory, Dr. K.S. Krishnan Marg, New Delhi-110012 (India)], E-mail: rkkotnala@gmail.com

2009-07-15

The structural magnetic and magneto-transport properties of double perovskite system Ba{sub 2-x}Sr{sub x}FeMoO{sub 6} (0{<=}x{<=}1.0) prepared in bulk polycrystalline form are reported in this paper. X-ray diffraction analysis showed that samples are single phase and the lattice constants decreases with increase in the Sr content. The degree of Fe-Mo ordering has been found decreasing in the series with an increase in the Sr content. Parent compound Ba{sub 2}FeMoO{sub 6} exhibits saturation magnetic moment value of 3.54 {mu}{sub B}/f.u. at 85 K in a magnetic field of 6000 Oe. Temperature dependence of resistivity shows metallic behavior for all the samples. The magneto-resistance (MR) of the compound with x=0.4 is higher than that of the other samples. At room temperature this system shows a saturation magnetization value of 1.73 {mu}{sub B}/f.u. and MR value of 7.08% (1 T). The observed variations in the structural and magnetic properties are attributed to the change of chemical pressure due to the substitution of Sr in place of Ba. The effect of antisite disorder (ASD) defects on magneto-transport properties is studied in more detail.

The Sr:Ba:Rb ratio and zircon typology in granitoid complexes of Sao Paulo, Parana and Minas Gerais states (Brazil)

International Nuclear Information System (INIS)

Wernick, E.; Galembeck, T.M.B.; Artur, A.C.; Rigo Junior, L.; Weber-Diefenbach, K.

1990-01-01

Chemical (Sr: Ba: Rb) and zircon typology data from the Nazare Paulista, Mairipora/Cantareira, Cunhaporanga, Tres Corregos, Morungaba, Socorro, Itu, Graciosa and Serra Carambei granitoid complexes from the states of Minas Gerais, Sao Paulo and Parana (SE/S Brazil) are presented and discussed. By the zircon typology method these complexes are reffered, respectively, to the 2nd crustal, 3rd crustal/low temperature C-A, low temperature C-A, medium temperature C-A, medium/high temperature C-A, K-SA/Alkaline and alkaline serie which are considered as generated under increasing temperature associated with a progressive major participation of mantellic material. All these series, with the exception of the medium to high temperature calc-alkaline complexes Socorro and Morungaba whose chemical data come from several laboratories, display different positions and behaviour in the Sr: Ba: Rb diagram which reinforce the use of the zircon typology method in the study of granitoids. From the 2nd crustal serie up to the medium temperature C-A serie the complexes show a regular shift in their chemical composition which became progressively richer in Sr and depleted in Rb. The highly differentiades hypersolvus Serra do Carambei granite is strongly enriched in Rb and impoverish in Ba with respect to the Itu and the Graciosa complex which itself is slighly more depleted in Sr than the Itu granite. (author)

Preparation of cauliflower-like shaped Ba0.6Sr0.4TiO3 powders by modified oxalate co-precipitation method

International Nuclear Information System (INIS)

Li Mingli; Xu Mingxia

2009-01-01

The quantitative barium-strontium titanyl oxalate (Ba 0.6 Sr 0.4 TiO(C 2 O 4 ) 2 .4H 2 O, BSTO) precursor powders were prepared by the modified oxalate co-preparation method. It was based on the cation-exchange reaction between the stoichiometric solutions of oxalotitanic acid (H 2 TiO(C 2 O 4 ) 2 , HTO) and barium + strontium nitrate solution containing stoichiometric quantities of Ba and Sr ions. The pyrolysis of BSTO at 800 deg. C/4 h in air produced the homogeneous cauliflower-like shaped barium-strontium titanate (Ba 0.6 Sr 0.4 TiO 3 , BST) powders. The effect of polyethylene glycol (PEG) on morphology of BSTO and BST powders was also investigated. The characterization studies were carried on the as-dried BSTO and calcined BST powders by various physicochemical techniques, IR, X-ray diffraction (XRD), scanning electron microscopy (SEM), etc. The BSTO and BST powders obtained by aforementioned technique without PEG were homogeneous with spherical shape. The particles grew into spindle shape with the effect of PEG

Phosphorescent and thermoluminescent properties of SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} phosphors prepared by solid state reaction method

Energy Technology Data Exchange (ETDEWEB)

Mothudi, B.M., E-mail: mothubm@unisa.ac.za [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Department of Physics, University of South Africa, P.O. Box 392, Pretoria, ZA 6031 (South Africa); Ntwaeaborwa, O.M. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Kumar, A.; Sohn, K. [Department of Material Science and Metallurgical Engineering, Sunchon National University, Sunchon, Chonam 540-742 (Korea, Republic of); Swart, H.C. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa)

2012-05-15

Long persistent SrAl{sub 2}O{sub 4}:Eu{sup 2+} phosphors co-doped with Dy{sup 3+} were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl{sub 2}O{sub 4} were observed in all the samples. The broad band emission spectra at 497 nm for SrAl{sub 2}O{sub 4}:Eu{sup 2+}, Dy{sup 3+} were observed and the emission is attributed to the 4f{sup 6}5d{sup 1} to 4f{sup 7} transition of Eu{sup 2+} ions. The samples annealed at 1100-1200 Degree-Sign C showed similar broad TL glow curves centered at 120 Degree-Sign C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy{sup 3+} ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.

Theoretical characterization of quaternary iridium based hydrides NaAeIrH{sub 6} (Ae = Ca, Ba and Sr)

Energy Technology Data Exchange (ETDEWEB)

Bouras, S. [Laboratory of Studies Surfaces and Interfaces of Solids Materials, Department of Physics, Faculty of Science, University of Setif 1, 19000 (Algeria); Ghebouli, B., E-mail: bghebouli@yahoo.fr [Laboratory of Studies Surfaces and Interfaces of Solids Materials, Department of Physics, Faculty of Science, University of Setif 1, 19000 (Algeria); Benkerri, M. [Laboratory of Studies Surfaces and Interfaces of Solids Materials, Department of Physics, Faculty of Science, University of Setif 1, 19000 (Algeria); Ghebouli, M.A., E-mail: med.amineghebouli@yahoo.fr [Microelectronic Laboratory (LMSE), University of Bachir Ibrahimi, Bordj-Bou-Arreridj 34000 (Algeria); Research Unit on Emerging Materials (RUEM), University of Setif 1, 19000 (Algeria); Choutri, H. [Microelectronic Laboratory (LMSE), University of Bachir Ibrahimi, Bordj-Bou-Arreridj 34000 (Algeria); Louail, L.; Chihi, T.; Fatmi, M. [Research Unit on Emerging Materials (RUEM), University of Setif 1, 19000 (Algeria); Bouhemadou, A. [Laboratory for Developing New Materials and Their Characterization, Department of Physics, Faculty of Science, University of Setif 1, 19000 (Algeria); Department of Physics and Astronomy, College of Science, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia); Khenata, R.; Khachai, H. [Laboratoire de Physique Quantique et de Modélisation Mathématique, Université de Mascara, 29000 (Algeria)

2015-01-15

The quaternary iridium based hydrides NaAeIrH{sub 6} (Ae = Ca, Ba and Sr) are promising candidates as hydrogen storage materials. We have studied the structural, elastic, electronic, optical and thermodynamic properties of NaAeIrH{sub 6} (Ae = Ca, Ba and Sr) within the generalized gradient approximation, the local density approximation (LDA) and mBj in the frame of density functional perturbation theory. These alloys have a large indirect Γ–X band gap. The thermodynamic functions were computed using the phonon density of states. The origin of the possible transitions from valence band to conduction band was illustrated. By using the complex dielectric function, the optical properties such as absorption, reflectivity, loss function, refractive index and optical conductivity have been obtained. - Graphical abstract: Real and imaginary parts of the dielectric function, the absorption spectrum α(ω), reflectivity R(ω) and energy-loss spectrum L(ω). - Highlights: • NaAeIrH{sub 6} (Ae = Ca, Ba and Sr) alloys have been investigated. • The elastic moduli, energy gaps are predicted. • The optical and thermal properties were studied.

Magnetic and electrical transport properties of La0.5A0.5CoO3 nanoparticles (A = Sr, Ca, and Ba)

International Nuclear Information System (INIS)

Roy, B.; Das, S.

2011-01-01

Research highlights: → La 0.5 A 0.5 CoO 3 (A = Sr, Ca, and Ba) nanoparticles prepared by sol-gel technique. → Size-induced metal-insulator transition in Sr- and Ba-doped samples. → Broad paramagnetic to ferromagnetic transition with large magnetic irreversibility. → Co 3+ ions in intermediate and Co 4+ in a mixture of intermediate and high spin states. → ac magnetization suggests magnetic cluster glass nature of the samples. - Abstract: We have investigated the effect of particle size on the electrical transport and magnetic properties of La 0.5 A 0.5 CoO 3 (A = Sr, Ca, and Ba) nanoparticles synthesized by sol-gel technique. A size-induced metal to insulator transition is observed in the resistivity behaviour of Sr- and Ba-doped samples as the dimension changes from higher to lower ones. The magnetoresistance exhibits almost linear behaviour throughout the studied field range. The zero-field-cooled (ZFC) and field-cooled (FC) magnetizations display a broad paramagnetic to ferromagnetic transition at T C with a large magnetic irreversibility. The magnetization results indicate that Co 3+ ions are in the intermediate spin state but Co 4+ ions stay in a mixture of intermediate and high spin states. The observed frequency dependent shoulder in the in-phase and the peak in the out of phase component of the ac susceptibility indicate the glassy nature of the samples. The analysis of the ac magnetization results suggests that the magnetic behaviour is consistent with the cluster glass model.

Rapid and efficient visible light photocatalytic dye degradation using AFe{sub 2}O{sub 4} (A = Ba, Ca and Sr) complex oxides

Energy Technology Data Exchange (ETDEWEB)

Vijayaraghavan, T. [PSG Institute of Advanced Studies, Coimbatore 641004 (India); Suriyaraj, S.P.; Selvakumar, R. [Nanobiotechnology Laboratory, PSG Institute of Advanced Studies, Coimbatore 641004 (India); Venkateswaran, R. [PSG Institute of Advanced Studies, Coimbatore 641004 (India); Ashok, Anuradha, E-mail: anu@psgias.ac.in [PSG Institute of Advanced Studies, Coimbatore 641004 (India)

2016-08-15

Highlights: • Alkaline earth ferrites AFe{sub 2}O{sub 4} (A = Ba, Ca and Sr) were synthesized by sol–gel method. • Visible light photocatalytic activity of these ferrites were studied using congo red dye degradation. • BaFe{sub 2}O{sub 4} exhibited the best photocatalytic activity under visible light (xenon lamp) irradiation; CaFe{sub 2}O{sub 4} was the best photocatalyst under natural sun light irradiation. - Abstract: Photocatalytic activity of spinel type complex oxides has been investigated in this study. Alkaline earth ferrites AFe{sub 2}O{sub 4} (A = Ba, Ca, Sr) were synthesized by sol–gel method. Structural characterizations reveal that the synthesized ferrites have orthorhombic crystal structures with different space groups and cell dimensions when they have different alkaline earth metals in their A site. All the synthesized ferrites exhibited their bandgap in the range 2.14–2.19 eV. Their photocatalytic activities were studied using congo red dye under sunlight and xenon lamp radiation. The substitution of Ba, Ca and Sr at A site of these ferrites had varying impact on dye degradation process. Under xenon lamp irradiation, BaFe{sub 2}O{sub 4} exhibited the highest percentage of dye degradation (92% after 75 min). However, CaFe{sub 2}O{sub 4} showed the fastest degradation of the dye (70% within 15 min). In the absence of irradiation, SrFe{sub 2}O{sub 4} showed the highest dye adsorption (44% after 75 min).

Enhancement of photoluminescence properties and modification of crystal structures of Si{sub 3}N{sub 4} doping Li{sub 2}Sr{sub 0.995}SiO{sub 4}:0.005Eu{sup 2+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Song, Kaixin, E-mail: kxsong@hdu.edu.cn [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Zhang, Fangfang [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Chen, Daqin [College of Materials Sciences and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Wu, Song; Zheng, Peng [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Huang, Qingming [Instrument Analysis and Testing Center, Fuzhou University, Fuzhou 350002 (China); Jiang, Jun [Ningbo Institute of Materials Technologies and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Xu, Junming; Qin, Huibin [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China)

2015-10-15

Highlights: • Si{sub 3}N{sub 4} modified Li{sub 2}Sr{sub 0.995}SiO{sub 4}:0.005Eu{sup 2+} phosphors were prepared. • The luminescence intensity of Li{sub 2}Sr{sub 0.995}SiO{sub 4}:Eu{sup 2+} was enhanced by doping Si{sub 3}N{sub 4}. • The fluorescence decay times and thermal stability were enhanced by doping Si{sub 3}N{sub 4}. - Abstract: Si{sub 3}N{sub 4} modified Li{sub 2}Sr{sub 0.995}SiO{sub 4}:0.005Eu{sup 2+} (Li{sub 2}Sr{sub 0.995}SiO{sub 4−3x/2}N{sub x}:0.005Eu{sup 2+}) phosphors were synthesized with the conventional solid-state reaction in the reduced atmosphere. The crystal structure and vibrational modes were analyzed by X-ray diffraction, Raman scattering spectroscopy and Rietveld crystal structure refinement. Photoluminescence (PL) and photoluminescence excitation (PLE) spectra showed that Li{sub 2}Sr{sub 0.995}SiO{sub 4−3x/2}N{sub x}:0.005Eu{sup 2+} powder exhibited a broad yellow emission band centered at 560 nm under the excitation of 460 nm visible light, due to the 4f{sup 6}5d{sup 1} → 4f{sup 7} transition of Eu{sup 2+}. The partial nitridation of Li{sub 2}Sr{sub 0.995}SiO{sub 4−3x/2}N{sub x}:0.005Eu{sup 2+} (x = 0.01) phosphors led to a large enhancement in the luminescence intensity, as much as 190%. At the same time, the fluorescence decay behavior curves further showed that the photoluminescence efficiencies of Li{sub 2}Sr{sub 0.995}SiO{sub 4−3x/2}N{sub x}:0.005Eu{sup 2+} phosphors were enhanced by addition of Si{sub 3}N{sub 4}. The temperature quenching characteristics confirmed that the oxynitride based Li{sub 2}Sr{sub 0.995}SiO{sub 4−3x/2}N{sub x}:0.005Eu{sup 2+} showed slightly higher stability. It is implied that Li{sub 2}Sr{sub 0.995}SiO{sub 4−3x/2}N{sub x}:0.005Eu{sup 2+} phosphors had a possible potential application on white LEDs to match blue light chips.

Iron valence in double-perovskite (Ba,Sr,Ca)2FeMoO6: isovalent substitution effect

International Nuclear Information System (INIS)

Yasukawa, Y.; Linden, J.; Chan, T.S.; Liu, R.S.; Yamauchi, H.; Karppinen, M.

2004-01-01

In the Fe-Mo based B-site ordered double-perovskite, A 2 FeMoO 6.0 , with iron in the mixed-valence II/III state, the valence value of Fe is not precisely fixed at 2.5 but may be fine-tuned by means of applying chemical pressure at the A-cation site. This is shown through a systematic 57 Fe Moessbauer spectroscopy study using a series of A 2 FeMoO 6.0 [A=(Ba,Sr) or (Sr,Ca)] samples with high degree of Fe/Mo order, the same stoichiometric oxygen content and also almost the same grain size. The isomer shift values and other hyperfine parameters obtained from the Moessbauer spectra confirm that Fe remains in the mixed-valence state within the whole range of A constituents. However, upon increasing the average cation size at the A site the precise valence of Fe is found to decrease such that within the A=(Ba,Sr) regime the valence of Fe is closer to II, while within the A=(Sr,Ca) regime it is closer to the actual mixed-valence II/III state. As the valence of Fe approaches II, the difference in charges between Fe and Mo increases, and parallel with this the degree of Fe/Mo order increases. Additionally, for the less-ordered samples an increased tendency of clustering of the antisite Fe atoms is deduced from the Moessbauer data

The transfer factors of I, Ba, Sr, Y and Zr from soil to leafy vegetables

International Nuclear Information System (INIS)

Luo Daling; Li Mianfeng; Weng Senhan; Wen Guanghao; Liu Xiaowei; Zhang Cunxiang; Zhang Zeng; Yu Junyue

1996-01-01

The transfer factors of I, Ba, Sr, Y and Zr from soil to leafy vegetables have been determined using method of radioisotope tracers and element content analysis. The effects of growth period, size of the vegetables, contents of the isotopes in the soil and other climatic factors on the transfer factors have also been studied

Photoluminescence and phosphorescence properties of Sr1-xZn2-y(PO4)2:Eux2+,Mny2+ phosphor for UV-based white-LEDs

International Nuclear Information System (INIS)

Jeong, Junho; Jayasimhadri, M.; Sueb Lee, Ho; Jang, Kiwan; Soo Yi, Soung; Hyun Jeong, Jung; Kim, Changdae

2009-01-01

Sr 1-x Zn 2-y (PO 4 ) 2 :Eu x 2+ ,Mn y 2+ (SZP: Eu x 2+ ,Mn y 2+ ) phosphors (x=0, 0.01 and y=0, 0.01) were prepared by using a stoichiometric solid-state reaction method and their photoluminescence and phosphorescence decay properties were investigated. The emission spectrum of SrZn 2 (PO 4 ) 2 :Eu 0.01 2+ , Mn 0.01 2+ measured under 400 nm excitation was composed of the violettish blue and the emerald green emissioins centered at 421 and 547 nm, respectively. The excitation wavelength of the emission peak at 547 nm was about 421 nm in the excitation spectrum of SZP:Mn 0.01 2+ . Since, this value is equal to the transition energy of Eu 2+ , the energy transfer from Eu 2+ to Mn 2+ in SZP:Eu 0.01 2+ ,Mn 0.01 2+ phosphor has been demonstrated. The CIE chromaticity coordinates of SZP:Eu 0.01 2+ ,Mn 0.01 2+ phosphor were (0.330, 0.328) under the excitation wavelength 375 nm at room temperature. The phosphorescence from SZP:Eu 0.01 2+ ,Mn 0.01 2+ could be seen by naked eyes for few seconds and it has persisted for about 4.4 h while monitoring by using a PMT spectrometer. Therefore, SZP:Eu x 2+ ,Mn y 2+ phosphor may be a potential candidate for the UV-based white light-emitting diodes (LEDs).

Upconversion luminescence of Er3+/Yb3+ doped Sr5(PO4)3OH phosphor powders

Science.gov (United States)

Mokoena, P. P.; Swart, H. C.; Ntwaeaborwa, O. M.

2018-04-01

Sr5(PO4)3OH co-doped with Er3+and Yb3+ powder phosphors were synthesized by urea combustion method. The crystal structure was analyzed using X-ray diffraction (XRD). Particle morphology was analyzed using a Jeol JSM 7800F thermal field emission scanning electron microscope (FE-SEM) and the chemical composition analysis was carried out using an Oxford Instruments AzTEC energy dispersive spectrometer (EDS) attached to the FE-SEM. Upconversion emission was measured by using a FLS980 Spectrometer equipped with a 980 nm NIR laser as the excitation source, and a photomultiplier (PMT) detector. The XRD data of the Sr5(PO4)3OH powder exhibited characteristic diffraction patterns of the hexagonal structure referenced in the standard JCPDS card number 00-033-1348. The sharp peaks revealed the formation of crystalline Sr5(PO4)3OH. The powders were made up of hexagonal nanospheres. The enhanced red emission due to the 4F9/2 → 4I15/2 transitions of Er3+ was observed and was attributed to up conversion (UC) energy transfer from Yb3+. The upconversion energy transfer mechanism from Yb3+ to Er3+ is discussed.

Determination of Sr, Ba, Rb, and Cs in biological reference materials using a radiochemical NAA group separation procedure

International Nuclear Information System (INIS)

Mizera, J.; Randa, Z.

2008-01-01

Strontium, barium, rubidium, and cesium in selected, predominantly biological, reference materials (NIST 1515, 1547, 1549, 1566a, 1571, 1577b, 2704, CTA-OTL-1, and Bowen's Kale) were determined using neutron activation analysis (NAA) in two different analytical modes - instrumental NAA with epithermal neutrons (ENAA), and NAA with radiochemical group separation of Sr-Ba and Rb-Cs (RNAA). The ENAA mode was based on long-term (5 h) irradiation of samples in a Cd shielding. The RNAA procedure was based on long-term (20 h) irradiation of samples, their decomposition / dissolution by alkaline-oxidative fusion, and precipitation of Sr and Ba sulfates, and sorption of Rb and Cs onto ammonium phosphomolybdate (APM). Both methods provided element contents in the analyzed reference materials consistent with certified and/or literature values. (author)

Structure and properties of (Sr, Ca)CuO2-BaCuO2 superlattices grown by pulsed laser interval deposition

NARCIS (Netherlands)

Koster, Gertjan; Verbist, Karen; Rijnders, Augustinus J.H.M.; Rogalla, Horst; van Tendeloo, Gustaav; Blank, David H.A.

2001-01-01

We report on the preparation of CuBa2(SrxCa1¿x)nCun¿1Oy compounds by fabrication of (Ba,Sr,Ca)CuO2 superlattices with pulsed laser deposition (PLD). A technique called interval deposition is used to suppress multi-level or island growth resulting in high-quality superlattice structures. Both, the

Enhanced emission of encaged-OH--free Ca12(1-x)Sr12xAl14O33:0.1%Gd3+ conductive phosphors via tuning the encaged-electron concentration for low-voltage FEDs.

Science.gov (United States)

Zhang, Meng; Liu, Yuxue; Yang, Jian; Zhu, Hancheng; Yan, Duanting; Zhang, Xinyang; Liu, Chunguang; Xu, Changshan; Zhang, Hong

2017-05-24

Encaged-OH - -free Ca 12(1-x) Sr 12x Al 14 O 33 :0.1%Gd 3+ conductive phosphors were prepared through a melt-solidification process in combination with a subsequent heat treatment. Absorption spectra showed that the maximum encaged-electron concentration was increased to 1.08 × 10 21 cm -3 through optimizing the doping amount of Sr 2+ (x = 0.005). Meanwhile, FTIR and Raman spectra indicated that pure Ca 11.94 Sr 0.06 Al 14 O 33 :0.1%Gd 3+ conductive phosphor without encaged OH - and C 2 2- anions was acquired. For the conductive powders heat-treated in air for different times, the encaged-electron concentrations were tuned from 1.02 × 10 21 to 8.3 × 10 20 cm -3 . ESR, photoluminescence, and luminescence kinetics analyses indicated that the emission at 312 nm mainly originated from Gd 3+ ions surrounded by encaged O 2- anions, while Gd 3+ ions surrounded by encaged electrons had a negative contribution to the UV emission due to the existence of an energy transfer process. Under low-voltage electron-beam excitation (3 kV), enhanced cathodoluminescence (CL) of the conductive phosphors could be achieved by tuning the encaged-electron concentrations. In particular, for the encaged-OH - -free conductive phosphor, the emission intensity of the CL was about one order of magnitude higher than that of the conductive phosphor containing encaged OH - anions. Our results suggested that the encaged-OH - -free conductive phosphors have potential application in low-voltage FEDs.

Study of the effects of additives on structural properties of the Ba{sub x}Sr{sub 1-x}Fe{sub 12}O{sub 19} hexaferrite; Estudo do efeito de aditivos nas propriedades estruturais da hexaferrita Ba{sub x}Sr{sub 1-x}Fe{sub 12}O{sub 19}

Energy Technology Data Exchange (ETDEWEB)

Alves, Y.S.; Pereira, C.A.; Farias, F.C.; Mello, P.S.; Alves, A.G.; Pereira, F.M.; Barroso, M.B., E-mail: yuri.link2@gmail.com [Universidade Federal do Cariri (UFCA), Juazeiro do Norte, CE (Brazil); Saraiva, I.R.; Conde, W.S. [DeVry Fanor, Fortaleza, CE (Brazil); Sombra, A.B. [Laboratorio de Telecomunicacoes e Ciencia e Engenharia de Materiais (LOCEM/UFC), Fortaleza, CE (Brazil)

2016-07-01

The Hexaferrites are magnetic ceramic materials chemically and thermally stable, low-cost and easy processing. The objective of this work was to study the effects of SiO2 and CaO additives on structural properties of hexaferrite Ba{sub x}Sr{sub 1-x}Fe{sub 12}O{sub 19}. The samples were characterized by scanning electron microscopy (SEM), X-Ray Diffraction (XRD) and quantified by the Rietveld method. The doped samples showed no structural change. With the concentration of dopant employed, there was a decrease in the sintering temperature of all samples Ba{sub x}Sr{sub 1-x}Fe{sub 12}O{sub 19} 1100 °C/5h to 1000 °C/2h. After addition of dopants, it was observed that the growth of the grains in the samples did not occur uniformly. This uneven growth can is being influenced by the concentrations of Ba and Sr atoms present in the samples, as well as some sort of reaction with the dopant elements. (author)

Persistent luminescence, TL and OSL characterization of beta irradiated SrAl2O4:Eu2+, Dy3+ combustion synthesized phosphor