WorldWideScience

Sample records for automotive fuels

  1. Hydrogen as automotive fuel

    International Nuclear Information System (INIS)

    Ambrosini, G.; Ciancia, A.; Pede, G.; Brighigna, M.

    1993-01-01

    Hydrogen fueled vehicles may just be the answer to the air pollution problem in highly polluted urban environments where the innovative vehicle's air pollution abatement characteristics would justify its high operating costs as compared with those of conventional automotive alternatives. This paper examines the feasibility of hydrogen as an automotive fuel by analyzing the following aspects: the chemical-physical properties of hydrogen in relation to its use in internal combustion engines; the modifications necessary to adapt internal combustion engines to hydrogen use; hydrogen fuel injection systems; current production technologies and commercialization status of hydrogen automotive fuels; energy efficiency ratings; environmental impacts; in-vehicle storage systems - involving the use of hydrides, high pressure systems and liquid hydrogen storage systems; performance in terms of pay-load ratio; autonomous operation; and operating costs. With reference to recent trial results being obtained in the USA, an assessment is also made of the feasibility of the use of methane-hydrogen mixtures as automotive fuels. The paper concludes with a review of progress being made by ENEA (the Italian Agency for New Technology, Energy and the Environment) in the development of fuel storage and electronic fuel injection systems for hydrogen powered vehicles

  2. Hydrogen as automotive fuel

    International Nuclear Information System (INIS)

    Dini, D.; Ciancia, A.; Pede, G.; Sglavo, V.; ENEA, Rome

    1992-01-01

    An assessment of the technical/economic feasibility of the use of hydrogen as an automotive fuel is made based on analyses of the following: the chemical- physical properties of hydrogen in relation to its use in internal combustion engines; the modifications necessary to adapt internal combustion engines to hydrogen use; hydrogen fuel injection systems - with water vapour injection, cryogenic injection, and the low or high pressure injection of hydrogen directly into the combustion chamber; the current commercialization status of hydrogen automotive fuels; energy efficiency ratings; environmental impacts; in-vehicle storage systems - involving the use of hydrides, high pressure systems and liquid hydrogen storage systems; performance in terms of pay-load ratio; autonomous operation; and operating costs. The paper concludes that, considering current costs for hydrogen fuel production, distribution and use, at present, the employment of hydrogen fuelled vehicles is feasible only in highly polluted urban environments where the innovative vehicle's air pollution abatement characteristics would justify its high operating costs as compared with those of conventional automotive alternatives

  3. Automotive Fuel and Exhaust Systems.

    Science.gov (United States)

    Irby, James F.; And Others

    Materials are provided for a 14-hour course designed to introduce the automotive mechanic to the basic operations of automotive fuel and exhaust systems incorporated on military vehicles. The four study units cover characteristics of fuels, gasoline fuel system, diesel fuel systems, and exhaust system. Each study unit begins with a general…

  4. Automotive fuel efficiency

    International Nuclear Information System (INIS)

    Abelson, P.H.

    1992-01-01

    For at least the remainder of this century, the United States faces a growing dependence on imported oil. Costs are substantial, and they will mount. In June 1992, net imports provided nearly 50% of supplies, and their cost was $4.3 billion. Cost of net imports of motor vehicles and parts amounted to $3.0 billion. The two items combined totaled more than the negative trade balance of $6.6 billion. The light-duty highway fleet alone accounted for 38.2% of U.S. oil consumption in 1988. Correspondingly, the fleet was a substantial emitter of air pollutants - NO x , CO, and nonmethane hydrocarbons. In addition, it was a major source of CO 2 . The twin problems of oil imports and pollution would be ameliorated if the fuel economy if cars and trucks could be improved and their emissions were also reduced. In principle, the mileage of US automobiles could be substantially improved. But on purchasing a car, U.S. buyers rank fuel efficiency eight when making their choice. They are attracted to options that lower mileage. Consumers also tend to prefer large cars over small ones for reasons of safety. Increasingly, buyers are purchasing light trucks and vans that have inferior fuel efficiency. As a result of the above trends, the average mileage of the US automotive fleet has been diminishing. As long as fuel is available at comparatively low prices and there is no federal requirement for better mileage, improvement is unlikely. Moreover, even if improvements were mandated, change would be slow

  5. Future automotive fuels

    International Nuclear Information System (INIS)

    Lepik, M.

    1993-01-01

    There are several important factors which are fundamental to the choice of alternative automobile fuels: the chain of energetic efficiency of fuels; costs; environmental friendliness; suitability for usual engines or adapting easiness; existing reserves of crude oil, natural gas or the fossil energy sources; and, alternatively, agricultural potentiality. This paper covers all these factors. The fuels dealt with in this paper are alcohol, vegetable oil, gaseous fuel, hydrogen and ammonia fuels. Renewable fuels are the most valuable forms of renewable energy. In addition to that rank, they can contribute to three other problem areas: agricultural surpluses, environmental degradation, and conservation of natural resources. Due to the competitive utilization of biomass for food energy production, bio-fuels should mainly be produced in those countries where an energy shortage is combined with a food surplus. The fuels arousing the most interest are alcohol and vegetable oil, the latter for diesel engines, even in northern countries. (au)

  6. 16 CFR 306.10 - Automotive fuel rating posting.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Automotive fuel rating posting. 306.10... AUTOMOTIVE FUEL RATINGS, CERTIFICATION AND POSTING Duties of Retailers § 306.10 Automotive fuel rating posting. (a) If you are a retailer, you must post the automotive fuel rating of all automotive fuel you...

  7. Automotive fuels from biomass via gasification

    International Nuclear Information System (INIS)

    Zhang, Wennan

    2010-01-01

    There exists already a market of bio-automotive fuels i.e. bioethanol and biodiesel produced from food crops in many countries. From the viewpoint of economics, environment, land use, water use and chemical fertilizer use, however, there is a strong preference for the use of woody biomass and various forest/agricultural residues as the feedstock. Thus, the production of 2nd generation of bio-automotive fuels i.e. synthetic fuels such as methanol, ethanol, DME, FT-diesel, SNG and hydrogen through biomass gasification seems promising. The technology of producing synthetic fuels is well established based on fossil fuels. For biomass, however, it is fairly new and the technology is under development. Starting from the present market of the 1st generation bio-automotive fuels, this paper is trying to review the technology development of the 2nd generation bio-automotive fuels from syngas platform. The production of syngas is emphasized which suggests appropriate gasifier design for a high quality syngas production. A number of bio-automotive fuel demonstration plant will be presented, which gives the state of the art in the development of BTS (biomass to synthetic fuels) technologies. It can be concluded that the 2nd generation bio-automotive fuels are on the way to a breakthrough in the transport markets of industrial countries especially for those countries with a strong forest industry. (author)

  8. 16 CFR 306.5 - Automotive fuel rating.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Automotive fuel rating. 306.5 Section 306.5... RATINGS, CERTIFICATION AND POSTING Duties of Refiners, Importers and Producers § 306.5 Automotive fuel rating. If you are a refiner, importer, or producer, you must determine the automotive fuel rating of all...

  9. Industrial thermoforming simulation of automotive fuel tanks

    International Nuclear Information System (INIS)

    Wiesche, Stefan aus der

    2004-01-01

    An industrial thermoforming simulation with regard to automotive plastic fuel tanks is presented including all relevant process stages. The radiative and conductive heat transfer during the reheat stage, the deformation and stress behaviour during the forming stage, and the final cooling stage are simulated. The modelling of the thermal and rheological behaviour of the involved material is investigated in greater detail. By means of experimental data it is found that modelling of the phase transition during the process is highly important for predicting correct wall thickness distributions

  10. Fuel System: Automotive Mechanics Instructional Program. Block 4.

    Science.gov (United States)

    O'Brien, Ralph D.

    The fourth of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in automotive fuel systems at the secondary and post secondary level. The material, as organized, is a suggested sequence of instruction within each block. Each…

  11. Automotive fuels survey. Part 4. Innovations or illusions

    Energy Technology Data Exchange (ETDEWEB)

    Troelstra, W.P.; Van Walwijk, M.; Bueckmann, M. [International Energy Agency Automotive Fuels Information Service IEA/AFIS, c/o Innas, Breda (Netherlands)

    1999-01-01

    Volumes 1 to 3 of the IEA/AFIS Automotive Fuels Survey, address the most well-known automotive fuels and fuel production routes. Less well-known fuels and energy sources that are not used in combustion engines, e.g. electricity, were excluded from these volumes. In this report fuel routes and fuels that have not been addressed in the first volumes will be analysed. In this report, each chapter starts with a short description of the fuel(route) and its status of development (e.g. if the idea has been abandoned or if the fuel is already sold at a fuel station). Then the different aspects of that fuel are described as far as the information is available. This is limited to information that can not be found in volumes one and two of the Automotive Fuels Survey. For example: for the diesel-water mixtures, the production of diesel is not be described. If comparisons are made, they are made either relative to an already described fuel(route) that is related (e.g. biogas will be compared with natural gas) or relative to diesel and gasoline as was done in volume 1 and 2 of the Automotive Fuels Survey. For some of the fuels, the relation with a fuel already covered in volume one and two is very strong. For these fuels more information can be found in the chapters on the related fuel in the other volumes of the Automotive Fuels Survey. The following fuels are covered in this report: biodiesel from used oil and fat, biodiesel and biogasoline from algae, diesel from hydrothermal upgrading, biogas, hythane, Fischer-Tropsch diesel, diesel-water blends, higher ethers, and electricity. 74 refs.

  12. Price transparency on the market for automotive fuels. Final report

    International Nuclear Information System (INIS)

    Meindert, L.; Van Schijndel, M.; Volkerink, B.

    2011-05-01

    The objective of this study is to answer the main question: which bottlenecks may obstruct the road to up-to-date, reliable and fully market covering price comparison services for the Dutch market for automotive fuels. [nl

  13. Fuel saver based on electromagnetic induction for automotive engine

    Science.gov (United States)

    Siregar, Houtman P.; Sibarani, Maradu

    2007-12-01

    In the considered research is designed and analyzed the performance of the fuel saver which is based on electromagnetic induction for automotive diesel engine. The fuel saver which is based on permanent magnet has sold in market and its performance has tested. In comparison to the former fuel saver, in the proposed work is produced fuel saver which is based on electromagnetic induction. The considered research is the continuation of my former work. Performance of the produced fuel saver which is installed in the fuel line of internal combustion engine rig is compared to the performance of the standard internal combustion engine rig Speed of the engine, wire diameter of coil, and number of coil which is coiled in the winding of the the fuel saver are chosen as the testing variables. The considered research has succeeded to design the fuel saver which is based on electromagnetic induction for saving the automotive fuel consumption. Results of the research show that the addition of the fuel saver which is based on electromagnetic induction to the flow of the diesel fuel can significantly save the automative fuel consumption. In addition the designed fuel saver can reduce the opacity of the emission gas.

  14. Automotive fuels and internal combustion engines: a chemical perspective.

    Science.gov (United States)

    Wallington, T J; Kaiser, E W; Farrell, J T

    2006-04-01

    Commercial transportation fuels are complex mixtures containing hundreds or thousands of chemical components, whose composition has evolved considerably during the past 100 years. In conjunction with concurrent engine advancements, automotive fuel composition has been fine-tuned to balance efficiency and power demands while minimizing emissions. Pollutant emissions from internal combustion engines (ICE), which arise from non-ideal combustion, have been dramatically reduced in the past four decades. Emissions depend both on the engine operating parameters (e.g. engine temperature, speed, load, A/F ratio, and spark timing) and the fuel. These emissions result from complex processes involving interactions between the fuel and engine parameters. Vehicle emissions are comprised of volatile organic compounds (VOCs), CO, nitrogen oxides (NO(x)), and particulate matter (PM). VOCs and NO(x) form photochemical smog in urban atmospheres, and CO and PM may have adverse health impacts. Engine hardware and operating conditions, after-treatment catalysts, and fuel composition all affect the amount and composition of emissions leaving the vehicle tailpipe. While engine and after-treatment effects are generally larger than fuel effects, engine and after-treatment hardware can require specific fuel properties. Consequently, the best prospects for achieving the highest efficiency and lowest emissions lie with optimizing the entire fuel-engine-after-treatment system. This review provides a chemical perspective on the production, combustion, and environmental aspects of automotive fuels. We hope this review will be of interest to workers in the fields of chemical kinetics, fluid dynamics of reacting flows, atmospheric chemistry, automotive catalysts, fuel science, and governmental regulations.

  15. Fuel Cells for Non-automotive Uses: Status and Prospects

    Energy Technology Data Exchange (ETDEWEB)

    Upreti, Girish [ORNL; Greene, David L [ORNL; Duleep, K. G. [ICF International; Sawhney, Rupinder S [ORNL

    2012-01-01

    Fuel cells are in varying stages ofcommercialization for both automotive and non-automotive applications. The fuel cell industry has made substantial progress but still needs to reduce costs and improve performance to compete successfully with established technologies. In just 5 years, costs have been reduced by a factor of two while improving efficiency and durability. Based on interviews with fuel cell manufacturers in the U.S., Japan and the EU and information from published sources, a model of non-automotive fuel cell markets is constructed and used to estimate the impacts of government policies and to project the potential evolution of the industry to 2025. The model includes the effects of learning-by-doing, scale economies and exogenous technological progress on component and system costs, estimates customer choices between fuel cell and competing established technologies, and attempts to measure the impacts of government policies. With continued policy support it appears likely that the industry can become self-sustaining within the next decade.

  16. INVESTIGATION OF PEM FUEL CELL FOR AUTOMOTIVE USE

    Directory of Open Access Journals (Sweden)

    A. K. M. Mohiuddin

    2015-11-01

    Full Text Available This paper provides a brief investigation on suitability of Proton-exchange  membrane fuel cells (PEMFCs as the source of power for transportation purposes. Hydrogen is an attractive alternative transportation fuel. It is the least polluting fuel that can be used in an internal combustion engine (ICE and it is widely available. If hydrogen is used in a fuel cell which converts the chemical energy of hydrogen into electricity, (NOx emissions are eliminated. The investigation was carried out on a  fuel cell car model by implementing polymer electrolyte membrane (PEM types of fuel cell as the source of power to propel the prototype car. This PEMFC has capability to propel the electric motor by converting chemical energy stored in hydrogen gas into useful electrical energy. PEM fuel cell alone is used as the power source for the electric motor without the aid of any other power source such as battery associated with it. Experimental investigations were carried out to investigate the characteristics of fuel cell used and the performance of the fuel cell car. Investigated papameters are the power it develops, voltage, current and speed it produces under different load conditions. KEYWORDS: fuel cell; automotive; proton exchange membrane; polymer electrolyte membrane; internal combustion engine

  17. Development of a solid oxide fuel cell (SOFC) automotive auxiliary power unit (APU) fueled by gasoline

    International Nuclear Information System (INIS)

    DeMinco, C.; Mukerjee, S.; Grieve, J.; Faville, M.; Noetzel, J.; Perry, M.; Horvath, A.; Prediger, D.; Pastula, M.; Boersma, R.; Ghosh, D.

    2000-01-01

    This paper describes the design and the development progress of a 3 to 5 auxiliary power unit (APU) based on a gasoline fueled solid oxide fuel cell (SOFC). This fuel cell was supplied reformate gas (reactant) by a partial oxidation (POx) catalytic reformer utilizing liquid gasoline and designed by Delphi Automotive Systems. This reformate gas consists mainly of hydrogen, carbon monoxide and nitrogen and was fed directly in to the SOFC stack without any additional fuel reformer processing. The SOFC stack was developed by Global Thermoelectric and operates around 700 o C. This automotive APU produces power to support future 42 volt vehicle electrical architectures and loads. The balance of the APU, designed by Delphi Automotive Systems, employs a packaging and insulation design to facilitate installation and operation on-board automobiles. (author)

  18. Prices, taxes and automotive fuel cross-border shopping

    International Nuclear Information System (INIS)

    Leal, Andres; Lopez-Laborda, Julio; Rodrigo, Fernando

    2009-01-01

    The aim of the present paper is to determine whether differences in automotive fuel prices among neighboring Autonomous Communities (i.e. Spanish political-administrative regions) affect the decisions taken by individuals regarding the region in which to purchase fuel. In particular, the intention is to discover if price increases in certain Autonomous Communities, as a result of the application of the regional tranche of the Hydrocarbon Retail Sales Tax (HRST) has affected fuel purchases in neighboring Communities. In order to achieve the above-mentioned objectives, the monthly purchases of automotive diesel in Aragon between January 2001 and March 2007 is estimated from the fuel price in Aragon, the relation between prices in each of the bordering Communities and Aragon, weighted by density of traffic, the number of vehicles registered in that Community, and three dummy variables representative of the implementation of the regional tranche of the HRST in Madrid, Catalonia, and Valencia. The paper finds empirical evidence to demonstrate a positive effect of the relative prices in the neighboring Communities and vehicle registrations, and also a negative effect of prices in Aragon, upon the acquisition of diesel in this region. In the case of Catalonia, some evidence suggests that the price effect may have been strengthened following the introduction of the regional tranche of the HRST in August 2004. (author)

  19. Automotive Fuel Processor Development and Demonstration with Fuel Cell Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nuvera Fuel Cells

    2005-04-15

    The potential for fuel cell systems to improve energy efficiency and reduce emissions over conventional power systems has generated significant interest in fuel cell technologies. While fuel cells are being investigated for use in many applications such as stationary power generation and small portable devices, transportation applications present some unique challenges for fuel cell technology. Due to their lower operating temperature and non-brittle materials, most transportation work is focusing on fuel cells using proton exchange membrane (PEM) technology. Since PEM fuel cells are fueled by hydrogen, major obstacles to their widespread use are the lack of an available hydrogen fueling infrastructure and hydrogen's relatively low energy storage density, which leads to a much lower driving range than conventional vehicles. One potential solution to the hydrogen infrastructure and storage density issues is to convert a conventional fuel such as gasoline into hydrogen onboard the vehicle using a fuel processor. Figure 2 shows that gasoline stores roughly 7 times more energy per volume than pressurized hydrogen gas at 700 bar and 4 times more than liquid hydrogen. If integrated properly, the fuel processor/fuel cell system would also be more efficient than traditional engines and would give a fuel economy benefit while hydrogen storage and distribution issues are being investigated. Widespread implementation of fuel processor/fuel cell systems requires improvements in several aspects of the technology, including size, startup time, transient response time, and cost. In addition, the ability to operate on a number of hydrocarbon fuels that are available through the existing infrastructure is a key enabler for commercializing these systems. In this program, Nuvera Fuel Cells collaborated with the Department of Energy (DOE) to develop efficient, low-emission, multi-fuel processors for transportation applications. Nuvera's focus was on (1) developing fuel

  20. Free automotive and heating fuels for home and farm

    International Nuclear Information System (INIS)

    Murray, K.

    1991-01-01

    This book is for farmers or any landowners with access to free materials, such as agricultural wastes, that can be converted with minimum expense to heating fuel of to ethanol for automotive use. Farmers can learn how to make and use stoves, furnaces or stills for processing their own free materials for their own use or their neighbors. If one is a good mechanic one can learn how to adjust carburetors, to start a business converting engines to burn ethanol. The book is intended to provide the information you need to make practical use of waste materials and to save money. The book contains five chapters: Ethanol feedstocks; Crops for burning; Conversion to fuel; Fuel Utilization; and Business Opportunities. These chapters have been processed separately for inclusion on the data base

  1. Dynamic characteristics of an automotive fuel cell system for transitory load changes

    DEFF Research Database (Denmark)

    Rabbani, Raja Abid; Rokni, Masoud

    2013-01-01

    A dynamic model of Polymer Electrolyte Membrane Fuel Cell (PEMFC) system is developed to investigate the behavior and transient response of a fuel cell system for automotive applications. Fuel cell dynamics are subjected to reactant flows, heat management and water transportation inside the fuel...

  2. 77 FR 29751 - Agency Information Collection Activity Under OMB Review: Automotive Fuel Economy Reports

    Science.gov (United States)

    2012-05-18

    ... R. Katz, Fuel Economy Division, Office of International Policy, Fuel Economy and Consumer Programs...-0059] Agency Information Collection Activity Under OMB Review: Automotive Fuel Economy Reports AGENCY... Transportation on whether a manufacturer will comply with an applicable average fuel economy standard for the...

  3. Compatibility of alternative fuels with advanced automotive gas turbine and stirling engines. A literature survey

    Science.gov (United States)

    Cairelli, J.; Horvath, D.

    1981-01-01

    The application of alternative fuels in advanced automotive gas turbine and Stirling engines is discussed on the basis of a literature survey. These alternative engines are briefly described, and the aspects that will influence fuel selection are identified. Fuel properties and combustion properties are discussed, with consideration given to advanced materials and components. Alternative fuels from petroleum, coal, oil shale, alcohol, and hydrogen are discussed, and some background is given about the origin and production of these fuels. Fuel requirements for automotive gas turbine and Stirling engines are developed, and the need for certain reseach efforts is discussed. Future research efforts planned at Lewis are described.

  4. Methanol as an Automotive Fuel : With Special Emphasis on Methanol-Gasoline Blends

    Science.gov (United States)

    1977-04-01

    This report reviews the available information on methanol as related to its potential use as an automotive fuel. Information gaps critical to assessment and future decisions are delineated and suggestions made for necessary R&D efforts. In this conte...

  5. Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends report is the authoritative reference for carbon dioxide (CO2) emissions,...

  6. Satisfaction of the Automotive Fleet Fuel Demand and Its Impact on the Oil Refining Industry

    Science.gov (United States)

    1980-12-01

    Because virtually all transportation fuels are based on petroleum, it is essential to include petroleum refining in any assessment of potential changes in the transportation system. A number of changes in the automotive fleet have been proposed to im...

  7. Sensitivities of Internal Combustion Automotive Engines to Variations in Fuel Properties

    Science.gov (United States)

    1982-02-01

    An assessment of the sensitivity of the automotive gasoline and diesel engines to variations in fuel properties has been made. The variables studied include H/C ratio, distillation range, aromatic content, ignition quality as determined by the octane...

  8. Dynamic Simulation of a Proton Exchange Membrane Fuel Cell System For Automotive Applications

    DEFF Research Database (Denmark)

    Rabbani, Raja Abid; Rokni, Masoud

    2012-01-01

    A dynamic model of the PEMFC system is developed to investigate the behaviour and transient response of the fuel cell system for automotive applications. The system accounts for the fuel cell stack with coolant, humidifier, heat exchangers and pumps. Governing equations for fuel cell and humidifier...

  9. Egyptian And International Automotive Diesel. Fuels: Specifications Meeting Challenges To Refining Industry

    International Nuclear Information System (INIS)

    Zayed, A.M.; EI Shamy, A.A.

    2004-01-01

    This paper presents a brief summary and comparison of Egyptian automotive diesel fuel to the international one. Recent legislation all over the world, requiring further reduction in sulfur, aromatics, T 90 and T 95 and increasing cetane value of the transportation diesel fuels, presents numerous technical and economic challenges to the refiners. While refiners grapple with these challenges, they will also face pressure from the increased demand of transportation diesel fuel and tighter capital restrictions. Overcome of these challenges makes a fair competition. A comparison of the Egyptian automotive diesel fuel and the international one will be a guide to locally and globally facing these challenges

  10. Dynamic characteristics of an automotive fuel cell system for transitory load changes

    OpenAIRE

    Rabbani, Raja Abid; Rokni, Masoud

    2013-01-01

    A dynamic model of Polymer Electrolyte Membrane Fuel Cell (PEMFC) system is developed to investigate the behavior and transient response of a fuel cell system for automotive applications. Fuel cell dynamics are subjected to reactant flows, heat management and water transportation inside the fuel cell. Therefore, a control-oriented model has been devised in Aspen Plus Dynamics, which accommodates electrochemical, thermal, feed flow and water crossover models in addition to two-phase calculatio...

  11. How "Green" Is Your Fuel? Creation and Comparison of Automotive Biofuels

    Science.gov (United States)

    Wagner, Eugene P.; Koehle, Maura A.; Moyle, Todd M.; Lambert, Patrick D.

    2010-01-01

    In recent years, biofuel development and use has risen significantly. This undergraduate laboratory experiment educates students on the various alternative fuels that are being developed for automotive applications and the advantages and disadvantages of each. Students replicate commercially available alternative fuels, E85 and biodiesel, as well…

  12. The development of natural gas as an automotive fuel in China

    International Nuclear Information System (INIS)

    Ma, Linwei; Geng, Jia; Li, Weqi; Liu, Pei; Li, Zheng

    2013-01-01

    This manuscript aims to systematically review the development of natural gas as an automotive fuel in China and to draw policy implications for decision making. This manuscript presents a brief overview of natural gas development and the potential of natural gas as an automotive fuel in China, followed by an introduction to the development of various technology pathways for using natural gas as an automotive fuel, including CNG (compressed natural gas) vehicles, LNG (liquefied natural gas) vehicles, and others. This material suggests, a large potential to increase the use of natural gas as an automotive fuel, especially for CNG and LNG vehicles. The following activities will promote the development of natural gas vehicles: prioritizing vehicle use in the utilization of natural gas, supporting the construction of natural gas filling stations, developing a favorable pricing policy for natural gas used in vehicles, and enhancing the research and development to further improve the technology performance, especially for the technology of LNG vehicles. -- Highlights: •An overview of the natural gas development in China. •A systematic introduction of the development of natural gas vehicles in China. •A review of the technological performance of natural gas vehicles. •Policy suggestions to promote the development of natural gas vehicles in China

  13. Bacterial contamination of automotive fuels in a tropical region: the case of Costa Rica

    OpenAIRE

    E. Rodríguez-Rodríguez, Carlos; Rodríguez-Cavallini, Evelyn; Blanco, Rigoberto

    2008-01-01

    Microbial contamination of fuel has been the cause of several problems in transportation and storage of these products. Due to the lack of previous studies related to these problems in Costa Rica, bacterial quality was evaluated biannually in automotive fuels stored in the four oil distribution facilities of the Costa Rican Petroleum Refinery (RECOPE). In 12 oil storage tanks, for a total of 96 samples, mesophilic, heterotrophic aerobic/facultative counts (ASTM D6974-04) and identification of...

  14. 75 FR 12470 - Automotive Fuel Ratings, Certification and Posting

    Science.gov (United States)

    2010-03-16

    ... biodiesel, biomass- based diesel, and blends thereof (collectively, ``biodiesel fuels'').\\2\\ \\1\\ The Fuel... is the octane rating, which covered entities must determine by deriving research octane and motor... exception of biodiesel fuels, for which the rating is the percentage of biodiesel or biomass- based diesel...

  15. Greenhouse gases - an up-date on the contribution of automotive fuels

    International Nuclear Information System (INIS)

    Williams, M.L.

    1992-01-01

    This paper examines the contribution to global emissions of greenhouse gases from automotive fuels. The Greenhouse Effect and Climate Change are explained briefly. Data is presented on the global warming potential of automobile emissions, actual measured emission rates and greenhouse gas emissions as CO 2 equivalents. It is concluded that insufficient data exists to assess accurately the contribution of automotive fuel use to all the important greenhouse gases. Over short timescales (say 20 years) low emission technologies do show significant reductions in CO 2 equivalent emissions compared with current technology vehicles. However, in the longer term, fuel economy rather than emissions of non-CO 2 gases, is likely to become the determining factor. (UK)

  16. Automotive fuel consumption in Brazil. Applying static and dynamic systems of demand equations

    International Nuclear Information System (INIS)

    Iootty, Mariana; Pinto, Helder Jr.; Ebeling, Francisco

    2009-01-01

    This paper aims to investigate and explain the performance of the Brazilian demand for automotive fuels in the period 1970-2005. It estimates the price and income elasticities for all the available fuels in the automotive sector in the country: gasoline, compressed natural gas (CNG), ethanol and diesel. The analysis of the expenditure allocation process among these fuels is carried out through the estimation of a linear approximation of an Almost Ideal Demand System (AIDS) model. Two estimation methods were implemented: the static (through a seemingly unrelated regression) and a dynamic (through a vector error correction model). Specification tests support the use of the latter. The empirical analysis suggests a high substitutability between gasoline and ethanol; being this relation higher than the one observed between gasoline and CNG. The study shows that gasoline, ethanol and diesel are normal goods, and with the exception of ethanol, they are expenditure elastic. CNG was estimated as an inferior good. (author)

  17. Automotive fuel consumption in Brazil: Applying static and dynamic systems of demand equations

    Energy Technology Data Exchange (ETDEWEB)

    Iootty, Mariana, E-mail: miootty@ie.ufrj.b [IE-UFRJ (Institute of Economics-Federal University of Rio de Janeiro), Energy Economics Group (Brazil); UFRRJ (Federal Rural University of Rio de Janeiro) (Brazil); Pinto, Helder [IE-UFRJ (Institute of Economics-Federal University of Rio de Janeiro), Energy Economics Group (Brazil); Ebeling, Francisco, E-mail: francisco.ebeling@ibp.org.b [Brazilian Petroleum Institute (Brazil)

    2009-12-15

    This paper aims to investigate and explain the performance of the Brazilian demand for automotive fuels in the period 1970-2005. It estimates the price and income elasticities for all the available fuels in the automotive sector in the country: gasoline, compressed natural gas (CNG), ethanol and diesel. The analysis of the expenditure allocation process among these fuels is carried out through the estimation of a linear approximation of an Almost Ideal Demand System (AIDS) model. Two estimation methods were implemented: the static (through a seemingly unrelated regression) and a dynamic (through a vector error correction model). Specification tests support the use of the latter. The empirical analysis suggests a high substitutability between gasoline and ethanol; being this relation higher than the one observed between gasoline and CNG. The study shows that gasoline, ethanol and diesel are normal goods, and with the exception of ethanol, they are expenditure elastic. CNG was estimated as an inferior good.

  18. Automotive fuel consumption in Brazil. Applying static and dynamic systems of demand equations

    Energy Technology Data Exchange (ETDEWEB)

    Iootty, Mariana [IE-UFRJ (Institute of Economics - Federal University of Rio de Janeiro), Energy Economics Group (Brazil); UFRRJ (Federal Rural University of Rio de Janeiro) (Brazil); Pinto, Helder Jr. [IE-UFRJ (Institute of Economics - Federal University of Rio de Janeiro), Energy Economics Group (Brazil); Ebeling, Francisco [Brazilian Petroleum Institute (Brazil)

    2009-12-15

    This paper aims to investigate and explain the performance of the Brazilian demand for automotive fuels in the period 1970-2005. It estimates the price and income elasticities for all the available fuels in the automotive sector in the country: gasoline, compressed natural gas (CNG), ethanol and diesel. The analysis of the expenditure allocation process among these fuels is carried out through the estimation of a linear approximation of an Almost Ideal Demand System (AIDS) model. Two estimation methods were implemented: the static (through a seemingly unrelated regression) and a dynamic (through a vector error correction model). Specification tests support the use of the latter. The empirical analysis suggests a high substitutability between gasoline and ethanol; being this relation higher than the one observed between gasoline and CNG. The study shows that gasoline, ethanol and diesel are normal goods, and with the exception of ethanol, they are expenditure elastic. CNG was estimated as an inferior good. (author)

  19. A survey of processes for producing hydrogen fuel from different sources for automotive-propulsion fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Brown, L.F.

    1996-03-01

    Seven common fuels are compared for their utility as hydrogen sources for proton-exchange-membrane fuel cells used in automotive propulsion. Methanol, natural gas, gasoline, diesel fuel, aviation jet fuel, ethanol, and hydrogen are the fuels considered. Except for the steam reforming of methanol and using pure hydrogen, all processes for generating hydrogen from these fuels require temperatures over 1000 K at some point. With the same two exceptions, all processes require water-gas shift reactors of significant size. All processes require low-sulfur or zero-sulfur fuels, and this may add cost to some of them. Fuels produced by steam reforming contain {approximately}70-80% hydrogen, those by partial oxidation {approximately}35-45%. The lower percentages may adversely affect cell performance. Theoretical input energies do not differ markedly among the various processes for generating hydrogen from organic-chemical fuels. Pure hydrogen has severe distribution and storage problems. As a result, the steam reforming of methanol is the leading candidate process for on-board generation of hydrogen for automotive propulsion. If methanol unavailability or a high price demands an alternative process, steam reforming appears preferable to partial oxidation for this purpose.

  20. Simulating the market for automotive fuel efficiency: The SHRSIM model

    Energy Technology Data Exchange (ETDEWEB)

    Greene, D.L.

    1987-02-01

    This report describes a computer model for simulating the effects of uncertainty about future fuel prices and competitors' behavior on the market shares of an automobile manufacturer who is considering introducing technology to increase fuel efficiency. Starting with an initial sales distribution, a pivot-point multinomial logit technique is used to adjust market shares based on changes in the present value of the added fuel efficiency. These shifts are random because the model generates random fuel price projections using parameters supplied by the user. The user also controls the timing of introduction and obsolescence of technology. While the model was designed with automobiles in mind, it has more general applicability to energy using durable goods. The model is written in IBM BASIC for an IBM PC and compiled using the Microsoft QuickBASIC (trademark of the Microsoft corporation) compiler.

  1. Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends Data

    Science.gov (United States)

    The Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends report is the authoritative reference for carbon dioxide (CO2) emissions, fuel economy, and powertrain technology trends for new personal vehicles in the United States. The ??Trends?? report has been published annually since 1975 and covers all passenger cars, sport utility vehicles, minivans, and all but the largest pickup trucks and vans. This report does not provide formal compliance values for EPA CO2 emissions standards and NHTSA CAFE standards. The downloadable data are available in PDF or spreadsheet (XLS) formats.

  2. Advanced Automotive Fuels Research, Development, and Commercialization Cluster (OH)

    Energy Technology Data Exchange (ETDEWEB)

    Linkous, Clovis; Hripko, Michael; Abraham, Martin; Balendiran, Ganesaratnam; Hunter, Allen; Lovelace-Cameron, Sherri; Mette, Howard; Price, Douglas; Walker, Gary; Wang, Ruigang

    2013-08-31

    Technical aspects of producing alternative fuels that may eventually supplement or replace conventional the petroleum-derived fuels that are presently used in vehicular transportation have been investigated. The work was centered around three projects: 1) deriving butanol as a fuel additive from bacterial action on sugars produced from decomposition of aqueous suspensions of wood cellulose under elevated temperature and pressure; 2) using highly ordered, openly structured molecules known as metal-organic framework (MOF) compounds as adsorbents for gas separations in fuel processing operations; and 3) developing a photocatalytic membrane for solar-driven water decomposition to generate pure hydrogen fuel. Several departments within the STEM College at YSU contributed to the effort: Chemistry, Biology, and Chemical Engineering. In the butanol project, sawdust was blended with water at variable pH and temperature (150 – 250{degrees}C), and heated inside a pressure vessel for specified periods of time. Analysis of the extracts showed a wide variety of compounds, including simple sugars that bacteria are known to thrive upon. Samples of the cellulose hydrolysate were fed to colonies of Clostridium beijerinckii, which are known to convert sugars to a mixture of compounds, principally butanol. While the bacteria were active toward additions of pure sugar solutions, the cellulose extract appeared to inhibit butanol production, and furthermore encouraged the Clostridium to become dormant. Proteomic analysis showed that the bacteria had changed their genetic code to where it was becoming sporulated, i.e., the bacteria were trying to go dormant. This finding may be an opportunity, as it may be possible to genetically engineer bacteria that resist the butanol-driven triggering mechanism to stop further fuel production. Another way of handling the cellulosic hydrolysates was to simply add the enzymes responsible for butanol synthesis to the hydrolytic extract ex-vivo. These

  3. Next Generation Bipolar Plates for Automotive PEM Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Adrianowycz, Orest; Norley, Julian; Stuart, David J; Flaherty, David; Wayne, Ryan; ; Williams, Warren; Tietze, Roger; Nguyen, Yen-Loan H; Zawodzinski, Tom; Pietrasz, Patrick

    2010-04-15

    The results of a successful U.S. Department of Energy (DoE) funded two-year $2.9 MM program lead by GrafTech International Inc. (GrafTech) are reported and summarized. The program goal was to develop the next generation of high temperature proton exchange membrane (PEM) fuel cell bipolar plates for use in transportation fuel cell applications operating at temperatures up to 120 °C. The bipolar plate composite developed during the program is based on GrafTech’s GRAFCELL resin impregnated flexible graphite technology and makes use of a high temperature Huntsman Advanced Materials resin system which extends the upper use temperature of the composite to the DoE target. High temperature performance of the new composite is achieved with the added benefit of improvements in strength, modulus, and dimensional stability over the incumbent resin systems. Other physical properties, including thermal and electrical conductivity of the new composite are identical to or not adversely affected by the new resin system. Using the new bipolar plate composite system, machined plates were fabricated and tested in high temperature single-cell fuel cells operating at 120 °C for over 1100 hours by Case Western Reserve University. Final verification of performance was done on embossed full-size plates which were fabricated and glued into bipolar plates by GrafTech. Stack testing was done on a 10-cell full-sized stack under a simulated drive cycle protocol by Ballard Power Systems. Freeze-thaw performance was conducted by Ballard on a separate 5-cell stack and shown to be within specification. A third stack was assembled and shipped to Argonne National Laboratory for independent performance verification. Manufacturing cost estimate for the production of the new bipolar plate composite at current and high volume production scenarios was performed by Directed Technologies Inc. (DTI). The production cost estimates were consistent with previous DoE cost estimates performed by DTI for the

  4. Mass Production Cost Estimation For Direct H2 PEM Fuel Cell Systesm for Automotive Applications. 2010 Update

    Energy Technology Data Exchange (ETDEWEB)

    James, Brian D. [Directed Technologies, Arlington, VA (United States); Kalinoski, Jeffrey A. [Directed Technologies, Arlington, VA (United States); Baum, Kevin N. [Directed Technologies, Arlington, VA (United States)

    2010-09-30

    This report is the fourth annual update of a comprehensive automotive fuel cell cost analysis. It contains estimates for material and manufacturing costs of complete 80 kWnet direct-hydrogen proton exchange membrane fuel cell systems suitable for powering light-duty automobiles.

  5. Mass Production Cost Estimation for Direct H2 PEM Fuel Cell Systems for Automotive Applications. 2009 Update

    Energy Technology Data Exchange (ETDEWEB)

    James, Brian D. [Directed Technologies, Arlington, VA (United States); Kalinoski, Jeffrey A. [Directed Technologies, Arlington, VA (United States); Baum, Kevin N. [Directed Technologies, Arlington, VA (United States)

    2010-01-01

    This report is the third annual update of a comprehensive automotive fuel cell cost analysis. It contains estimates for material and manufacturing cost of complete 80 kWnet direct hydrogen proton exchange membrane fuel cell systems suitable for powering light duty automobiles.

  6. Permeability of EVOH Barrier Material Used in Automotive Applications: Metrology Development for Model Fuel Mixtures

    Directory of Open Access Journals (Sweden)

    Zhao Jing

    2015-02-01

    Full Text Available EVOH (Ethylene-Vinyl Alcohol materials are widely used in automotive applications in multi-layer fuel lines and tanks owing to their excellent barrier properties to aromatic and aliphatic hydrocarbons. These barrier materials are essential to limit environmental fuel emissions and comply with the challenging requirements of fast changing international regulations. Nevertheless, the measurement of EVOH permeability to model fuel mixtures or to their individual components is particularly difficult due to the complexity of these systems and their very low permeability, which can vary by several orders of magnitude depending on the permeating species and their relative concentrations. This paper describes the development of a new automated permeameter capable of taking up the challenge of measuring minute quantities as low as 1 mg/(m2.day for partial fluxes for model fuel mixtures containing ethanol, i-octane and toluene at 50°C. The permeability results are discussed as a function of the model fuel composition and the importance of EVOH preconditioning is emphasized for accurate permeability measurements. The last part focuses on the influence of EVOH conditioning on its mechanical properties and its microstructure, and further illustrates the specific behavior of EVOH in presence of ethanol oxygenated fuels. The new metrology developed in this work offers a new insight in the permeability properties of a leading barrier material and will help prevent the consequences of (bioethanol addition in fuels on environmental emissions through fuel lines and tanks.

  7. Survey evidence on the willingness of U.S. consumers to pay for automotive fuel economy

    International Nuclear Information System (INIS)

    Greene, David L.; Evans, David H.; Hiestand, John

    2013-01-01

    Prospect theory holds that human beings faced with a risky bet will tend to value potential losses about twice as much as potential gains. Previous research has demonstrated that prospect theory could be sufficient to explain an energy paradox in the market for automotive fuel economy. This paper analyzes data from questions added to four commercial, multi-client surveys of 1000 U.S. households each in 2004, 2011, 2012 and 2013. Households were asked about willingness to pay for future fuel savings as well as the annual fuel savings necessary to justify a given upfront payment. Payback periods inferred from household responses are generally consistent over time and across different formulations of questions. Mean calculated payback periods are about 3 years, but there is substantial dispersion among individual responses. The calculated payback periods do not appear to be correlated with the attributes of respondents. Respondents were able to quantitatively describe their uncertainty about both vehicle fuel economy and future fuel prices. Simulation of loss averse behavior based on respondents’ stated uncertainty illustrates how loss aversion could lead consumers to substantially undervalue future fuel savings relative to their expected value. - Highlights: • Payback periods were calculated from stated willingness to pay for fuel savings in 4 US surveys. • US car buyers expect payback in 3 years in order to pay more for increased fuel economy. • Respondents’ payback periods are uncorrelated with their socio-economic attributes. • Survey respondents consider fuel economy ratings and future fuel prices highly uncertain. • The survey results are consistent with the behavioral economic principle of loss aversion

  8. The emulsistem device; Water in gasoil emulsions as fuel for automotive diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Ciccarelli, U. (AgipPetroli (Italy))

    1987-02-01

    The use of water in fuel emulsions as well as the introduction of water in the combustion chamber of engines is a practice known from the first years of this century. The technique permits a good atomisation of the fuel in the combustion chamber, this implying a faster and more complete combustion reaction. The use of water in fuel emulsions on a Diesel engine allows the following advantages, - a drastic reduction of the smoke intensity, a drastic reduction of NOx emissions, a small reduction of the specific fuel consumption, an optimization of the combustion processes (higher combustion efficiency and reduction of deposit formation), and a reduction of the engine maintenance costs. AgipPetroli, in collaboration with Telesia, has developed a new static emulgator for emulsions suitable for combustion chamber injection. It is convenient for automotive appliclations, specifically for Diesel engines. The main components of the Emulsistem device are the mixer and the emulgator. Both can easily be inserted in the fuel feed circuit. Water and fuel are first coarsely mixed in the mixer; the subsequent passage of this mixer through the emulgator leads to a fine emulsion. The water in gasoil emulsion is fed to the Diesel engine injector. The system is briefly described and illustrated by graphs. (AB).

  9. Status and Outlook for the U.S. Non-Automotive Fuel Cell Industry: Impacts of Government Policies and Assessment of Future Opportunities

    Energy Technology Data Exchange (ETDEWEB)

    Greene, David L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Duleep, K. G. [ICF International, Fairfax, VA (United States); Upreti, Girish [Univ. of Tennessee, Knoxville, TN (United States)

    2011-05-15

    Non-Automotive Fuel Cell Industry, Government Policy and Future Opportunities. Fuel cells (FCs)are considered essential future energy technologies by developed and developing economies alike. Several countries, including the United States, Japan, Germany,and South Korea have established publicly funded R&D and market transformation programs to develop viable domestic FC industries for both automotive and nonautomotive applications.

  10. State of the art: Multi-fuel reformers for automotive fuel cell applications. Problem identification and research needs

    Energy Technology Data Exchange (ETDEWEB)

    Westerholm, R. [Stockholm Univ. (Sweden). Dept. of Analytical Chemistry; Pettersson, L.J. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    1999-12-01

    On an assignment from the Transport and Communications Research Board (KFB) a literature study and a study trip to the USA and Great Britain have been performed. The literature study and the study trip was made during late spring and autumn 1999.The purpose of the project was to collect available information about the chemical composition of the product gas from a multi-fuel reformer for a fuel cell vehicle. It was furthermore to identify problems and research needs. The report recommends directions for future major research efforts. The results of the literature study and the study trip led to the following general conclusions: With the technology available today it does not seem feasible to develop a highly efficient and reliable multi-fuel reformer for automotive applications, i. e. for applications where all types of fuels ranging from natural gas to heavy diesel fuels can be used. The potential for developing a durable and reliable system is considerably higher if dedicated fuel reformers are used.The authors propose that petroleum-derived fuels should be designed for potential use in mobile fuel cell applications. In the present literature survey and the site visit discussions we found that there are relatively low emissions from fuel cell engines compared to internal combustion engines. However, the major research work on reformers/fuel cells have been performed during steady-state operation. Emissions during start-up, shutdown and transient operation are basically unknown and must be investigated in more detail. The conclusions and findings in this report are based on open/available information, such as discussions at site visits, reports, scientific publications and symposium proceedings.

  11. Preparation, characterization and degradation mechanisms of PtCu alloy nanoparticles for automotive fuel cells

    Science.gov (United States)

    Marcu, A.; Toth, G.; Srivastava, R.; Strasser, P.

    2012-06-01

    Electrochemically dealloyed PtCu alloy nanoparticles successfully meet the automotive technology target of having four times higher Pt mass activity for the electroreduction of molecular oxygen compared to current state-of-the-art platinum catalysts [1]. However, the catalysts must also maintain their activity throughout the aggressive automotive drive-cycles in order to be implemented in fuel cells cars. Here, the durability of dealloyed PtCu catalysts was systematically evaluated under various voltage-cycles using a rotating ring disk electrode. The stability of the non-noble metal alloy component was proven at electrode potentials below 0.6 V. The platinum stability was evaluated at potentials up to 1.1 V to avoid carbon corrosion and then up to 1.2 V to be closer to the more aggressive cycles developed in startup/shutdown events of the fuel cells. The major known failure modes such as non-noble metal dissolution, platinum dissolution, and particle growth/agglomeration were monitored in order to understand closely the PtCu nanoparticles behavior under different potential cycles and to provide a degradation fingerprint.

  12. Multiwalled carbon nanotubes and fluoroelastomer antistatic nanocomposite for automotive fuel system components

    International Nuclear Information System (INIS)

    Lee, Seok; Park, Seong Hwan; Ha, Kiryong; Lee, Jong Cheol

    2016-01-01

    Fluoroelastomer (FKM) composites, reinforced with multiwalled carbon nanotubes (MWNTs), were prepared by conventional method to determine the possibility of using MWNTs to develop an antistatic composite in automotive fuel systems. The results obtained from the composite containing 0-9 phr of MWNTs were compared. A 5 points increase in hardness was achieved with the addition of only 1 phr of MWNTs and 9 phr added FKM composite was increased 6.4MPa in tensile strength compared to the MWNTs unfilled FKM composite. In addition, electrical conductivity increased from 0 to 1.039 Scm -1 with increase in the MWNTs concentration, and the dynamic damping property was increased in the rubbery state region accordingly. These phenomena can be explained by the MWNTs networks formed in FKM matrix. This research will therefore be useful in the development of an antistatic rubber composite for fuel system components, which are deformed or vibrated while in operation.

  13. Multiwalled carbon nanotubes and fluoroelastomer antistatic nanocomposite for automotive fuel system components

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seok; Park, Seong Hwan; Ha, Kiryong [Keimyung University, Daegu (Korea, Republic of); Lee, Jong Cheol [Jin-Yang Oil Seal Co., Ltd., Daegu (Korea, Republic of)

    2016-03-15

    Fluoroelastomer (FKM) composites, reinforced with multiwalled carbon nanotubes (MWNTs), were prepared by conventional method to determine the possibility of using MWNTs to develop an antistatic composite in automotive fuel systems. The results obtained from the composite containing 0-9 phr of MWNTs were compared. A 5 points increase in hardness was achieved with the addition of only 1 phr of MWNTs and 9 phr added FKM composite was increased 6.4MPa in tensile strength compared to the MWNTs unfilled FKM composite. In addition, electrical conductivity increased from 0 to 1.039 Scm{sup -1} with increase in the MWNTs concentration, and the dynamic damping property was increased in the rubbery state region accordingly. These phenomena can be explained by the MWNTs networks formed in FKM matrix. This research will therefore be useful in the development of an antistatic rubber composite for fuel system components, which are deformed or vibrated while in operation.

  14. Costs and benefits of automotive fuel economy improvement: A partial analysis

    Energy Technology Data Exchange (ETDEWEB)

    Greene, D.L. [Oak Ridge National Lab., TN (United States); Duleep, K.G. [Energy and Environmental Analysis, Inc., Arlington, VA (United States)

    1992-03-01

    This paper is an exercise in estimating the costs and benefits of technology-based fuel economy improvements for automobiles and light trucks. Benefits quantified include vehicle cots, fuel savings, consumer`s surplus effects, the effect of reduced weight on vehicle safety, impacts on emissions of CO{sub 2} and criteria pollutants, world oil market and energy security benefits, and the transfer of wealth from US consumes to oil producers. A vehicle stock model is used to capture sales, scrappage, and vehicle use effects under three fuel price scenarios. Three alternative fuel economy levels for 2001 are considered, ranging from 32.9 to 36.5 MPG for cars and 24.2 to 27.5 MPG for light trucks. Fuel economy improvements of this size are probably cost-effective. The size of the benefit, and whether there is a benefit, strongly depends on the financial costs of fuel economy improvement and judgments about the values of energy security, emissions, safety, etc. Three sets of values for eight parameters are used to define the sensitivity of costs and benefits to key assumptions. The net present social value (1989$) of costs and benefits ranges from a cost of $11 billion to a benefit of $286 billion. The critical parameters being the discount rate (10% vs. 3%) and the values attached to externalities. The two largest components are always the direct vehicle costs and fuel savings, but these tend to counterbalance each other for the fuel economy levels examined here. Other components are the wealth transfer, oil cost savings, CO{sub 2} emissions reductions, and energy security benefits. Safety impacts, emissions of criteria pollutants, and consumer`s surplus effects are relatively minor components. The critical issues for automotive fuel economy are therefore: (1) the value of present versus future costs and benefits, (2) the values of external costs and benefits, and (3) the financially cost-effective level of MPG achievable by available technology. 53 refs.

  15. Costs and benefits of automotive fuel economy improvement: A partial analysis

    Energy Technology Data Exchange (ETDEWEB)

    Greene, D.L. (Oak Ridge National Lab., TN (United States)); Duleep, K.G. (Energy and Environmental Analysis, Inc., Arlington, VA (United States))

    1992-03-01

    This paper is an exercise in estimating the costs and benefits of technology-based fuel economy improvements for automobiles and light trucks. Benefits quantified include vehicle cots, fuel savings, consumer's surplus effects, the effect of reduced weight on vehicle safety, impacts on emissions of CO{sub 2} and criteria pollutants, world oil market and energy security benefits, and the transfer of wealth from US consumes to oil producers. A vehicle stock model is used to capture sales, scrappage, and vehicle use effects under three fuel price scenarios. Three alternative fuel economy levels for 2001 are considered, ranging from 32.9 to 36.5 MPG for cars and 24.2 to 27.5 MPG for light trucks. Fuel economy improvements of this size are probably cost-effective. The size of the benefit, and whether there is a benefit, strongly depends on the financial costs of fuel economy improvement and judgments about the values of energy security, emissions, safety, etc. Three sets of values for eight parameters are used to define the sensitivity of costs and benefits to key assumptions. The net present social value (1989$) of costs and benefits ranges from a cost of $11 billion to a benefit of $286 billion. The critical parameters being the discount rate (10% vs. 3%) and the values attached to externalities. The two largest components are always the direct vehicle costs and fuel savings, but these tend to counterbalance each other for the fuel economy levels examined here. Other components are the wealth transfer, oil cost savings, CO{sub 2} emissions reductions, and energy security benefits. Safety impacts, emissions of criteria pollutants, and consumer's surplus effects are relatively minor components. The critical issues for automotive fuel economy are therefore: (1) the value of present versus future costs and benefits, (2) the values of external costs and benefits, and (3) the financially cost-effective level of MPG achievable by available technology. 53 refs.

  16. Investigation of degradation effects in polymer electrolyte fuel cells under automotive-related operating conditions

    Science.gov (United States)

    Enz, S.; Dao, T. A.; Messerschmidt, M.; Scholta, J.

    2015-01-01

    The influence of artificial starvation effects during automotive-related operating conditions is investigated within a polymer electrolyte fuel cell (PEFC) using non-dispersive infrared sensors and a current scan shunt. Driving cycles (DC) and single load change experiments are performed with specific fuel and oxidant starvation conditions. Within the DC experiments, a maximal CO2 amount of 4.67 μmol per cycle is detected in the cathode and 0.97 μmol per cycle in the anode exhaust without reaching fuel starvation conditions during the DC. Massive cell reversal conditions occur within the single load change experiments as a result of anodic fuel starvation. As soon as a fuel starvation appears, the emitted CO2 increases exponentially in the anode and cathode exhaust. A maximal CO2 amount of 143.8 μmol CO2 on the anode side and 5.8 μmol CO2 on the cathode side is detected in the exhaust gases. The critical cell reversal conditions only occur by using hydrogen reformate as anode reactant. The influence of the starvation effects on the PEFC performance is investigated via polarization curves, cyclic and linear sweep voltammetry as well as electrochemical impedance spectroscopy. The PEFC performance is reduced by 47% as a consequence of the dynamic operation.

  17. Technology development goals for automotive fuel cell power systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    James, B.D.; Baum, G.N.; Kuhn, I.F. Jr. [Directed Technologies, Inc., Arlington, VA (United States)

    1994-08-01

    This report determines cost and performance requirements for Proton Exchange Membrane (PEM) fuel cell vehicles carrying pure H{sub 2} fuel, to achieve parity with internal combustion engine (ICE) vehicles. A conceptual design of a near term FCEV (fuel cell electric vehicle) is presented. Complete power system weight and cost breakdowns are presented for baseline design. Near term FCEV power system weight is 6% higher than ICE system, mid-term FCEV projected weights are 29% lower than ICE`s. There are no inherently high-cost components in FCE, and at automotive production volumes, near term FCEV cost viability is closer at hand than at first thought. PEM current vs voltage performance is presented for leading PEM manufacturers and researchers. 5 current and proposed onboard hydrogen storage techniques are critically compared: pressurized gas, cryogenic liquid, combined pressurized/cryogenic, rechargeable hydride, adsorption. Battery, capacitor, and motor/controller performance is summarized. Fuel cell power system component weight and cost densities (threshold and goal) are tabulated.

  18. Engineering-economic analyses of automotive fuel economy potential in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Greene, D.L.; DeCicco, J.

    2000-02-01

    Over the past 25 years more than 20 major studies have examined the technological potential to improve the fuel economy of passenger cars and light trucks in the US. The majority has used technology/cost analysis, a combination of analytical methods from the disciplines of economics and automotive engineering. In this paper the authors describe the key elements of this methodology, discuss critical issues responsible for the often widely divergent estimates produced by different studies, review the history of its use, and present results from six recent assessments. Whereas early studies tended to confine their scope to the potential of proven technology over a 10-year time period, more recent studies have focused on advanced technologies, raising questions about how best to include the likelihood of technological change. The paper concludes with recommendations for further research.

  19. Bacterial contamination of automotive fuels in a tropical region: the case of Costa Rica.

    Science.gov (United States)

    Rodríguez-Rodríguez, Carlos E; Rodríguez-Cavallini, Evelyn; Blanco, Rigoberto

    2009-09-01

    Microbial contamination of fuel has been the cause of several problems in transportation and storage of these products. Due to the lack of previous studies related to these problems in Costa Rica, bacterial quality was evaluated biannually in automotive fuels stored in the four oil distribution facilities of the Costa Rican Petroleum Refinery (RECOPE). In 12 oil storage tanks, for a total of 96 samples, mesophilic, heterotrophic aerobic/facultative counts (ASTM D6974-04) and identification of bacteria presented in regular gas, premium gas and diesel from the bottom and superior part of the tanks were done; in the samples containing an aqueous phase, sulfate reducing bacteria (SRB) were also quantified by the most probable number technique (MPN), according to the ASTM D4412-84 standard. The higher contamination was shown at the bottom of the tanks (populations up to 10(4) UFC/l), especially if there was accumulated water, in which case populations reached 10(8) UFC/l. The most contaminated fuel was diesel (counts up to 10(4) UFC/l), whereas the less contaminated was premium gas. The less contaminated fuels were from the facilities of La Garita and Barranca, whereas the most contaminated were from Ochomogo. Nevertheless, the quantified populations did not cause significant alteration in quality physicochemical parameters in the samples analyzed. A total of 149 bacterial strains were isolated, 136 (91.3%) Gram positive and 13 (8.7%) Gram negative. The most frequent genera were Staphylococcus (24.0%), Micrococcus (21.9%), Bacillus (18.8%) and Kocuria (11.5%) among Gram positive bacteria and Pseudomonas (7.3%) among Gram negative bacteria. The majority of these genera have been found as fuel contaminants or even as degraders of this kind of products; nevertheless, some species for which their appearance or growth in hydrocarbons have not been described were found with low frequencies. SRB were present in counts up to 10(5) MPN/l in 42.9% of water containing samples

  20. Characterizing automotive fuel cell materials by soft x-ray scanning transmission x-ray microscopy

    International Nuclear Information System (INIS)

    Hitchcock, A. P.; Lee, V.; Wu, J.; Cooper, G.; West, M. M.; Berejnov, V.; Soboleva, T.; Susac, D.; Stumper, J.

    2016-01-01

    Proton-Exchange Membrane Fuel Cell (PEM-FC) based engines are being developed rapidly for near-term implementation in hydrogen fueled, mass production, personal automobiles. Research is focused on understanding and controlling various degradation processes (carbon corrosion, Pt migration, cold start), and reducing cost by reducing or eliminating Pt catalyst. We are using soft X-ray scanning transmission X-ray microscopy (STXM) at the S 2p, C 1s, O 1s and F 1s edges to study a variety of issues related to optimization of PEM-FC materials for automotive applications. A method to efficiently and accurately measure perfluorosulfonic acid distributions was developed and is being used to better understand how different loadings and preparation methods affect the ionomer distribution in the cathode. Progress towards an environmental cell capable of controlling the temperature and humidity of a PEM-FC sample in the STXM is described. Methods for studying the 3D chemical structure of PEM-FC are outlined

  1. Sorbent Material Property Requirements for On-Board Hydrogen Storage for Automotive Fuel Cell Systems.

    Energy Technology Data Exchange (ETDEWEB)

    Ahluwalia, R. K.; Peng, J-K; Hua, T. Q.

    2015-05-25

    Material properties required for on-board hydrogen storage in cryogenic sorbents for use with automotive polymer electrolyte membrane (PEM) fuel cell systems are discussed. Models are formulated for physical, thermodynamic and transport properties, and for the dynamics of H-2 refueling and discharge from a sorbent bed. A conceptual storage configuration with in-bed heat exchanger tubes, a Type-3 containment vessel, vacuum insulation and requisite balance-of-plant components is developed to determine the peak excess sorption capacity and differential enthalpy of adsorption for 5.5 wt% system gravimetric capacity and 55% well-to-tank (WTT) efficiency. The analysis also determines the bulk density to which the material must be compacted for the storage system to reach 40 g.L-1 volumetric capacity. Thermal transport properties and heat transfer enhancement methods are analyzed to estimate the material thermal conductivity needed to achieve 1.5 kg.min(-1) H-2 refueling rate. Operating temperatures and pressures are determined for 55% WTT efficiency and 95% usable H-2. Needs for further improvements in material properties are analyzed that would allow reduction of storage pressure to 50 bar from 100 bar, elevation of storage temperature to 175-200 K from 150 K, and increase of WTT efficiency to 57.5% or higher.

  2. Developing compressed natural gas as an automotive fuel in Nigeria: Lessons from international markets

    International Nuclear Information System (INIS)

    Ogunlowo, Olufemi O.; Bristow, Abigail L.; Sohail, M.

    2015-01-01

    The Nigerian government proposed the use of compressed natural gas (CNG) as an automotive fuel in 1997 as part of the initiatives to harness natural gas (NG) resources but progress has been slow. This paper examines the natural gas vehicle (NGV) implementation approaches and outcomes in seven countries with diverse experiences in order to gain an understanding of the barriers to the NGV market development in Nigeria. The analysis employs hermeneutic principles to secondary data derived from academic literature, published reports from a variety of international agencies, grey literature, and text from online sources and identifies eight success factors for NGV market development namely: strategic intent, legal backing, learning and adaptation, assignment of responsibilities, financial incentives, NG pricing, consumer confidence, and NG infrastructure. The paper concludes that the principal impediment to NGV market development in Nigeria is the uncoordinated implementation approach and that greater government involvement is required in setting strategic goals, developing the legal and regulatory frameworks, setting of clear standards for vehicles and refuelling stations as well as assigning responsibilities to specific agencies. Short-term low cost policy interventions identified include widening the existing NG and gasoline price gap and offering limited support for refuelling and retrofitting facilities. - Highlights: • We examined the NGV policies and implementation strategies in selected countries. • The use of legislative mandates help deepen NGV penetration. • Aligning stakeholder interest is critical to NGV adoption. • Making national interest a priority ahead of regional infrastructure is a critical success factor. • Government support drives participation

  3. A study on the environmental impact of automotive fuels in the quality of the air in metropolitan area of São Paulo period from 2001 to 2005

    OpenAIRE

    Waldir Nunes dos Santos Junior

    2006-01-01

    The environmental impact of the automotive fuels in the quality of the air is one of the great problems of the current world. The present work had as objective to evaluate the air quality in RMSP (Metropolitan Area of São Paulo), in the period from 2001 to 2005. It presents, mainly, a study of the impact of the emissions of gases for light automotive vehicles, taking into account the PROCONVE (Program of Control of Automotive Air Pollution). The methodology involved a comparative study of the...

  4. Lightweight Design Solutions in the Automotive Field: Environmental Modelling Based on Fuel Reduction Value Applied to Diesel Turbocharged Vehicles

    Directory of Open Access Journals (Sweden)

    Massimo Delogu

    2016-11-01

    Full Text Available A tailored model for the assessment of environmental benefits achievable by “light-weighting” in the automotive field is presented. The model is based on the Fuel Reduction Value (FRV coefficient, which expresses the Fuel Consumption (FC saving involved by a 100 kg mass reduction. The work is composed of two main sections: simulation and environmental modelling. Simulation modelling performs an in-depth calculation of weight-induced FC whose outcome is the FRV evaluated for a wide range of Diesel Turbocharged (DT vehicle case studies. Environmental modelling converts fuel saving to impact reduction basing on the FRVs obtained by simulations. Results show that for the considered case studies, FRV is within the range 0.115–0.143 and 0.142–0.388 L/100 km × 100 kg, respectively, for mass reduction only and powertrain adaptation (secondary effects. The implementation of FRVs within the environmental modelling represents the added value of the research and makes the model a valuable tool for application to real case studies of automotive lightweight LCA.

  5. Are today's automotive technician students ready for the increased use of ethanol fuels: A study of students' perceptions of ethanol and the effects of E20

    Science.gov (United States)

    Mead, Gary R.

    As the price of petroleum rises, the use of alternative fuels such as ethanol will continue to increase. As ethanol use increases, consumers are asking automotive technicians questions about the fuel. But how much do automotive technicians know about ethanol? In order to answer this question, a study was conducted to describe automotive technician students' knowledge, attitudes, and perceptions of ethanol as a vehicle fuel. Automotive students were chosen because they will be tomorrow's generation of technicians who will be working on vehicles that have used ethanol fuels along with flex fuel vehicles. The students were selected from six two-year technical colleges located in southern Minnesota. The six schools were chosen because they are located in areas where ethanol use is prevalent. The study used a 33-question pencil-and-paper survey to measure 184 automotive students' perceptions of ethanol. The survey revealed that students' knowledge of ethanol is very superficial. They know well advertised terms and facts, but lack an in-depth knowledge of the fuel. Also, it was discovered that several myths about ethanol still exist. Because of the lack of knowledge on technical aspects of the fuel, it is recommended that instructors in automotive programs incorporate a one to two hour class covering ethanol fuels into their courses. The second part of this study was a review of several material compatibility studies conducted at Minnesota State University, Mankato on 20% ethanol blends. The studies were conducted on fuel system rubbers, plastics, and metals. Minnesota recently enacted a law that will require all gasoline sold in the state to contain 20% ethanol. These studies were reviewed to see if 20% ethanol, E20, will cause any vehicle fuel system problems that automotive technicians should know about. After reviewing the studies it was determined that the likelihood of fuel system problems from E20 would be very small and isolated. Even though the potential for

  6. European Automotive Congress

    CERN Document Server

    Clenci, Adrian

    2016-01-01

    The volume includes selected and reviewed papers from the European Automotive Congress held in Bucharest, Romania, in November 2015. Authors are experts from research, industry and universities coming from 14 countries worldwide. The papers are covering the latest developments in fuel economy and environment, automotive safety and comfort, automotive reliability and maintenance, new materials and technologies, traffic and road transport systems, advanced engineering methods and tools, as well as advanced powertrains and hybrid and electric drives.

  7. Lightweighting Automotive Materials for Increased Fuel Efficiency and Delivering Advanced Modeling and Simulation Capabilities to U.S. Manufacturers

    Energy Technology Data Exchange (ETDEWEB)

    Hale, Steve

    2013-09-11

    Abstract The National Center for Manufacturing Sciences (NCMS) worked with the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL), to bring together research and development (R&D) collaborations to develop and accelerate the knowledgebase and infrastructure for lightweighting materials and manufacturing processes for their use in structural and applications in the automotive sector. The purpose/importance of this DOE program: • 2016 CAFÉ standards. • Automotive industry technology that shall adopt the insertion of lightweighting material concepts towards manufacturing of production vehicles. • Development and manufacture of advanced research tools for modeling and simulation (M&S) applications to reduce manufacturing and material costs. • U.S. competitiveness that will help drive the development and manufacture of the next generation of materials. NCMS established a focused portfolio of applied R&D projects utilizing lightweighting materials for manufacture into automotive structures and components. Areas that were targeted in this program: • Functionality of new lightweighting materials to meet present safety requirements. • Manufacturability using new lightweighting materials. • Cost reduction for the development and use of new lightweighting materials. The automotive industry’s future continuously evolves through innovation, and lightweight materials are key in achieving a new era of lighter, more efficient vehicles. Lightweight materials are among the technical advances needed to achieve fuel/energy efficiency and reduce carbon dioxide (CO2) emissions: • Establish design criteria methodology to identify the best materials for lightweighting. • Employ state-of-the-art design tools for optimum material development for their specific applications. • Match new manufacturing technology to production volume. • Address new process variability with new production-ready processes.

  8. Bacterial contamination of automotive fuels in a tropical region: the case of Costa Rica

    Directory of Open Access Journals (Sweden)

    Carlos E Rodríguez-Rodríguez

    2009-09-01

    Full Text Available Microbial contamination of fuel has been the cause of several problems in transportation and storage of these products. Due to the lack of previous studies related to these problems in Costa Rica, bacterial quality was evaluated biannually in automotive fuels stored in the four oil distribution facilities of the Costa Rican Petroleum Refinery (RECOPE. In 12 oil storage tanks, for a total of 96 samples, mesophilic, heterotrophic aerobic/facultative counts (ASTM D6974-04 and identification of bacteria presented in regular gas, premium gas and diesel from the bottom and superior part of the tanks were done; in the samples containing an aqueous phase, sulfate reducing bacteria (SRB were also quantified by the most probable number technique (MPN, according to the ASTM D4412-84 standard. The higher contamination was shown at the bottom of the tanks (populations up to 10(4 UFC/l, especially if there was accumulated water, in which case populations reached 10(8 UFC/l. The most contaminated fuel was diesel (counts up to 10(4 UFC/l, whereas the less contaminated was premium gas. The less contaminated fuels were from the facilities of La Garita and Barranca, whereas the most contaminated were from Ochomogo. Nevertheless, the quantified populations did not cause significant alteration in quality physicochemical parameters in the samples analyzed. A total of 149 bacterial strains were isolated, 136 (91.3% Gram positive and 13 (8.7% Gram negative. The most frequent genera were Staphylococcus (24.0%, Micrococcus (21.9%, Bacillus (18.8% and Kocuria (11.5% among Gram positive bacteria and Pseudomonas (7.3% among Gram negative bacteria. The majority of these genera have been found as fuel contaminants or even as degraders of this kind of products; nevertheless, some species for which their appearance or growth in hydrocarbons have not been described were found with low frequencies. SRB were present in counts up to 10(5 MPN/l in 42.9% of water containing samples

  9. Standardized Curriculum for Automotive Mechanics.

    Science.gov (United States)

    Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

    Standardized curricula are provided for two courses for the secondary vocational education program in Mississippi: automotive mechanics I and II. The six units in automotive mechanics I are as follows: orientation and safety; tools, equipment, and manuals; measurement; automotive engines; basic electrical systems; and fuel systems. Automotive…

  10. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT III, MAINTAINING THE FUEL SYSTEM--DETROIT DIESEL ENGINE.

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM. TOPICS ARE (1) PURPOSE OF THE FUEL SYSTEM, (2) TRACING THE FUEL FLOW, (3) MINOR COMPONENTS OF THE FUEL SYSTEM, (4) MAINTENANCE TIPS, (5) CONSTRUCTION AND FUNCTION OF THE FUEL INJECTORS, AND (6)…

  11. Modeling of Pem Fuel Cell Systems Including Controls and Reforming Effects for Hybrid Automotive Applications

    National Research Council Canada - National Science Library

    Boettner, Daisie

    2001-01-01

    .... This study develops models for a stand-alone Proton Exchange Membrane (PEM) fuel cell stack, a direct-hydrogen fuel cell system including auxiliaries, and a methanol reforming fuel cell system for integration into a vehicle performance simulator...

  12. Towards Highly Performing and Stable PtNi Catalysts in Polymer Electrolyte Fuel Cells for Automotive Application

    Directory of Open Access Journals (Sweden)

    Sabrina C. Zignani

    2017-03-01

    Full Text Available In order to help the introduction on the automotive market of polymer electrolyte fuel cells (PEFCs, it is mandatory to develop highly performing and stable catalysts. The main objective of this work is to investigate PtNi/C catalysts in a PEFC under low relative humidity and pressure conditions, more representative of automotive applications. Carbon supported PtNi nanoparticles were prepared by reduction of metal precursors with formic acid and successive thermal and leaching treatments. The effect of the chemical composition, structure and surface characteristics of the synthesized samples on their electrochemical behavior was investigated. The catalyst characterized by a larger Pt content (Pt3Ni2/C presented the highest catalytic activity (lower potential losses in the activation region among the synthesized bimetallic PtNi catalysts and the commercial Pt/C, used as the reference material, after testing at high temperature (95 °C and low humidification (50% conditions for automotive applications, showing a cell potential (ohmic drop-free of 0.82 V at 500 mA·cm−2. In order to assess the electro-catalysts stability, accelerated degradation tests were carried out by cycling the cell potential between 0.6 V and 1.2 V. By comparing the electrochemical and physico-chemical parameters at the beginning of life (BoL and end of life (EoL, it was demonstrated that the Pt1Ni1/C catalyst was the most stable among the catalyst series, with only a 2% loss of voltage at 200 mA·cm−2 and 12.5% at 950 mA·cm−2. However, further improvements are needed to produce durable catalysts.

  13. The fuel cell: a coming technology for the cogeneration and the automotive; La pile a combustible: une technologie d'avenir pour la cogeneration et l'automobile

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    In the framework of the Eco-Industries 2000 meeting, the ATEE organized a colloquium on the fuel cell use in the automotive and cogeneration industries. This book presents the six papers proposed at this colloquium bringing information on the fuel cell market, design and advantages. In the automotive domain, the fuel cell integration in the future car at Renault is presented. The PEM (Proton Exchange Membrane) concept is also detailed. (A.L.B.)

  14. Evaluation of Techniques for Reducing In-Use Automotive Fuel Consumption

    Science.gov (United States)

    1981-04-01

    This report presents an assessment of proposed techniques for reducing fuel consumption in the in-use light duty road vehicle fleet. Three general classes of techniques are treated: (1) modification of vehicles, (2) modification of traffic flow, and ...

  15. Pyrolysis of automotive shredder residue for the production of fuel-grade gas

    International Nuclear Information System (INIS)

    Sharp, L.L.; Ness, R.O. Jr.

    1993-01-01

    Every year eight to ten million cars and trucks are disposed of by shredding at one of the 200 auto shredders located in the United States. Automotive shredder residue (ASR) is a by-product created in the dismantling of automobiles. Figure 1 illustrates the process by which ASR is generated. An automobile is stripped of useful and/or hazardous items, such as the gas tank, battery, tires, and radiator. Although it is beneficial to have these items removed for safety and environmental concerns, this is not always accomplished. After removal of some or all of these items, the automobile is shredded to provide a material less than 4 inches in size and composed of approximately 50% organic and 50% inorganic fractions. Ferrous scrap is then separated out magnetically. This ferrous scrap supplies the steel industry with 12 to 14 million tons per year for electric arc furnace feedstock. Air cyclone separators isolate a low density open-quotes fluffclose quotes from the nonferrous fraction (aluminum, copper, etc.). This fluff (shredder residue) is composed of a variety of plastics, fabrics, foams, glass, rubber, and an assortment of contaminants. Fluff bulk density is approximately 20 lb/ft

  16. Model-based diagnosis through Structural Analysis and Causal Computation for automotive Polymer Electrolyte Membrane Fuel Cell systems

    Science.gov (United States)

    Polverino, Pierpaolo; Frisk, Erik; Jung, Daniel; Krysander, Mattias; Pianese, Cesare

    2017-07-01

    The present paper proposes an advanced approach for Polymer Electrolyte Membrane Fuel Cell (PEMFC) systems fault detection and isolation through a model-based diagnostic algorithm. The considered algorithm is developed upon a lumped parameter model simulating a whole PEMFC system oriented towards automotive applications. This model is inspired by other models available in the literature, with further attention to stack thermal dynamics and water management. The developed model is analysed by means of Structural Analysis, to identify the correlations among involved physical variables, defined equations and a set of faults which may occur in the system (related to both auxiliary components malfunctions and stack degradation phenomena). Residual generators are designed by means of Causal Computation analysis and the maximum theoretical fault isolability, achievable with a minimal number of installed sensors, is investigated. The achieved results proved the capability of the algorithm to theoretically detect and isolate almost all faults with the only use of stack voltage and temperature sensors, with significant advantages from an industrial point of view. The effective fault isolability is proved through fault simulations at a specific fault magnitude with an advanced residual evaluation technique, to consider quantitative residual deviations from normal conditions and achieve univocal fault isolation.

  17. Considerations for Using Composite Pressure Vessels (CPVs) in Fuel Storage for Automotive Applications

    Science.gov (United States)

    Cone, Darren; Greene, Nathanael; Beeson, Harold; McCloskey, David

    2013-01-01

    Ongoing initiative to get high energy capacity "green fuel" containers to market quickly and cost effectively. The United States has decided to invest in "green energy" technology, to become energy independent, and to "Innovate Our Way to a Clean Energy Future."

  18. Automotive Engines; Automotive Mechanics I: 9043.03.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    This automotive engines course studies and demonstrates the theory and principles of operation of the automotive four stroke cycle engine. The student will develop an understanding of the systems necessary to make the engine perform as designed, such as cooling, fuel, ignition and lubrication. This is a one or two quinmester credit course of 45…

  19. Assessment of methane-related fuels for automotive fleet vehicles: technical, supply, and economic assessments

    Energy Technology Data Exchange (ETDEWEB)

    1982-02-01

    The use of methane-related fuels, derived from a variety of sources, in highway vehicles is assessed. Methane, as used here, includes natural gas (NG) as well as synthetic natural gas (SNG). Methanol is included because it can be produced from NG or the same resources as SNG, and because it is a liquid fuel at normal ambient conditions. Technological, operational, efficiency, petroleum displacement, supply, safety, and economic issues are analyzed. In principle, both NG and methanol allow more efficient engine operation than gasoline. In practice, engines are at present rarely optimized for NG and methanol. On the basis of energy expended from resource extraction to end use, only optimized LNG vehicles are more efficient than their gasoline counterparts. By 1985, up to 16% of total petroleum-based highway vehicle fuel could be displaced by large fleets with central NG fueling depots. Excluding diesel vehicles, which need technology advances to use NG, savings of 8% are projected. Methanol use by large fleets could displace up to 8% of petroleum-based highway vehicle fuel from spark-ignition vehicles and another 9% from diesel vehicles with technology advances. The US NG supply appears adequate to accommodate fleet use. Supply projections, future price differential versus gasoline, and user economics are uncertain. In many cases, attractive paybacks can occur. Compressed NG now costs on average about $0.65 less than gasoline, per energy-equivalent gallon. Methanol supply projections, future prices, and user economics are even more uncertain. Current and projected near-term methanol supplies are far from adequate to support fleet use. Methanol presently costs more than gasoline on an equal-energy basis, but is projected to cost less if produced from coal instead of NG or petroleum.

  20. Impact of the electric compressor for automotive air conditioning system on fuel consumption and performance analysis

    Science.gov (United States)

    Zulkifli, A. A.; Dahlan, A. A.; Zulkifli, A. H.; Nasution, H.; Aziz, A. A.; Perang, M. R. M.; Jamil, H. M.; Misseri, M. N.

    2015-12-01

    Air conditioning system is the biggest auxiliary load in a vehicle where the compressor consumed the largest. Problem with conventional compressor is the cooling capacity cannot be control directly to fulfill the demand of thermal load inside vehicle cabin. This study is conducted experimentally to analyze the difference of fuel usage and air conditioning performance between conventional compressor and electric compressor of the air conditioning system in automobile. The electric compressor is powered by the car battery in non-electric vehicle which the alternator will recharge the battery. The car is setup on a roller dynamometer and the vehicle speed is varied at 0, 30, 60, 90 and 110 km/h at cabin temperature of 25°C and internal heat load of 100 and 400 Watt. The results shows electric compressor has better fuel consumption and coefficient of performance compared to the conventional compressor.

  1. Biofuels in Spain: Market penetration analysis and competitiveness in the automotive fuel market

    Energy Technology Data Exchange (ETDEWEB)

    Sobrino, Fernando Hernandez; Monroy, Carlos Rodriguez [Department of Business Administration, School of Industrial Engineering, Universidad Politecnica de Madrid, Jose Gutierrez Abascal 2, 28006 Madrid (Spain); Perez, Jose Luis Hernandez [High School Chemistry Teacher, Madrid (Spain)

    2010-12-15

    For several years the European Union (E.U.) has been promoting the use of biofuels due to their potential benefits such as the reduction of dependence on foreign energy imports (the raw materials can be produced within the E.U.), the more stable fossil fuel prices (they can replace fossil fuels on the market), the greenhouse gas (GHG) reduction (biofuels' raw materials fix CO{sub 2} from the atmosphere) and the fact that they can represent an additional source of income for the primary sector (biofuels' raw materials are vegetables that can be grown and harvested). Despite the public aids (direct and indirect), biofuels are not competitive with fossil fuels at present, but it is possible that in the future the environment conditions change and biofuels might become competitive. It is difficult to assess whether this will happen or not, but it is possible to make an assessment of a future situation. This article presents two analyses with one objective: to determine if biofuels might become competitive in the future. The first analysis examines the dependencies of two quotations which have a strong relationship with fuels: the crude oil quotation and the CO{sub 2} bond quotation. The analysis of these relationships may help to forecast the future competitiveness of biofuels. For instance, biofuels' future competitiveness will be higher if their raw material costs are not related to crude oil quotations or if they are related in a negative way (the higher the crude oil quotations the lower the raw material biofuels' cost). The second analysis focuses on the market penetration of biofuels in the Spanish market. There are data related to biofuels monthly consumption in Spain since 2007 and it is possible to know if biofuels are gaining market quota since then. (author)

  2. Biofuels in Spain: Market penetration analysis and competitiveness in the automotive fuel market

    International Nuclear Information System (INIS)

    Sobrino, Fernando Hernandez; Monroy, Carlos Rodriguez; Perez, Jose Luis Hernandez

    2010-01-01

    For several years the European Union (E.U.) has been promoting the use of biofuels due to their potential benefits such as the reduction of dependence on foreign energy imports (the raw materials can be produced within the E.U.), the more stable fossil fuel prices (they can replace fossil fuels on the market), the greenhouse gas (GHG) reduction (biofuels' raw materials fix CO 2 from the atmosphere) and the fact that they can represent an additional source of income for the primary sector (biofuels' raw materials are vegetables that can be grown and harvested). Despite the public aids (direct and indirect), biofuels are not competitive with fossil fuels at present, but it is possible that in the future the environment conditions change and biofuels might become competitive. It is difficult to assess whether this will happen or not, but it is possible to make an assessment of a future situation. This article presents two analyses with one objective: to determine if biofuels might become competitive in the future. The first analysis examines the dependencies of two quotations which have a strong relationship with fuels: the crude oil quotation and the CO 2 bond quotation. The analysis of these relationships may help to forecast the future competitiveness of biofuels. For instance, biofuels' future competitiveness will be higher if their raw material costs are not related to crude oil quotations or if they are related in a negative way (the higher the crude oil quotations the lower the raw material biofuels' cost). The second analysis focuses on the market penetration of biofuels in the Spanish market. There are data related to biofuels monthly consumption in Spain since 2007 and it is possible to know if biofuels are gaining market quota since then. (author)

  3. Production of ethyl alcohol by fermentation and its utilization as automotive fuel

    Energy Technology Data Exchange (ETDEWEB)

    Lima, J.E.

    1980-03-01

    Alcohol has an excellent future as a fuel, and its large-scale production from sugar-bearing feedstocks should definitely be a stabilizing factor in the economics of the international sugar industry. This article approaches the subject from the sugar industry viewpoint, with emphasis on the underdeveloped countries. The economic data presented here are only approximations so as to give some idea as to the order of magnitude of the capital and operating costs involved. All economic projections are based on conditions prevailing during the third quarter of 1979.

  4. Assessment of institutional barriers to the use of natural gas fuel in automotive vehicle fleets

    Science.gov (United States)

    Jablonski, J.; Lent, L.; Lawrence, M.; White, L.

    1983-01-01

    Institutional barriers to the use of natural gas as a fuel for motor vehicle fleets were identified. Recommendations for barrier removal were developed. Eight types of institutional barriers were assessed: (1) lack of a national standard for the safe design and certification of natural gas vehicles and refueling stations; (2) excessively conservative or misapplied state and local regulations, including bridge and tunnel restrictions, restrictions on types of vehicles that may be fueled by natural gas, zoning regulations that prohibit operation of refueling stations, parking restrictions, application of LPG standards to LNG vehicles, and unintentionally unsafe vehicle or refueling station requirements; (3) need for clarification of EPA's tampering enforcement policy; (4) the U.S. hydrocarbon standard; (5) uncertainty concerning state utility commission jurisdiction; (6) sale for resale prohibitions imposed by natural gas utility companies or state utility commissions; (7) uncertainty of the effects of conversions to natural gas on vehicle manufactures warranties; and (8) need for a natural gas to gasoline equivalent units conversion factor for use in calculation of state road use taxes.

  5. Metal/ceria water-gas shift catalysts for automotive polymer electrolyte fuel cell system

    International Nuclear Information System (INIS)

    Myers, D. J.; Krebs, J. F.; Carter, J. D.; Kumar, R.; Krumpelt, M.

    2002-01-01

    Polymer electrolyte fuel cell (PEFC) systems are a leading candidate for replacing the internal combustion engine in light duty vehicles. One method of generating the hydrogen necessary for the PEFC is reforming a liquid fuel, such as methanol or gasoline, via partial oxidation, steam reforming, or autothermal reforming (a combination of partial oxidation and steam reforming). The H(sub 2)-rich reformate can contain as much as 10% carbon monoxide. Carbon monoxide has been shown to poison the platinum-based anode catalyst at concentrations as low as 10 ppm,1 necessitating removal of CO to this level before passing the reformate to the fuel cell stack. The water-gas shift (WGS) reaction, CO+ H(sub 2)O(rightleftharpoons) CO(sub 2)+ H(sub 2), is used to convert the bulk of the reformate CO to CO(sub 2). Industrially, the WGS reaction is conducted over two catalysts, which operate in different temperature regimes. One catalyst is a FeCr mixed oxide, which operates at 350-450 C and is termed the high-temperature shift (HTS) catalyst. The second catalyst is a CuZn mixed oxide, which operates at 200-250 C and is termed the low-temperature shift (LTS) catalyst. Although these two catalysts are used industrially in the production of H(sub 2) for ammonia synthesis, they have major drawbacks that make them unsuitable for transportation applications. Both the LTS and the HTS catalysts must first be ''activated'' before being used. For example, the copper in the copper oxide/zinc oxide LTS catalyst must first be reduced to elemental copper in situ before it becomes active for the WGS reaction. This reduction reaction is exothermic and must be carried out under well- controlled conditions using a dilute hydrogen stream (1 vol% H(sub 2)) to prevent high catalyst temperatures, which can result in sintering (agglomeration) of the copper particles and loss of active surface area for the WGS reaction. Also, once the catalyst has been activated by reduction, it must be protected from

  6. Fischer–tropsch diesel production and evaluation as alternative automotive fuel in pilot-scale integrated biomass-to-liquid process

    International Nuclear Information System (INIS)

    Kim, Young-Doo; Yang, Chang-Won; Kim, Beom-Jong; Moon, Ji-Hong; Jeong, Jae-Yong; Jeong, Soo-Hwa; Lee, See-Hoon; Kim, Jae-Ho; Seo, Myung-Won; Lee, Sang-Bong; Kim, Jae-Kon; Lee, Uen-Do

    2016-01-01

    Highlights: • A pilot scale biomass-to-liquid (BTL) process was investigated for Fischer-Tropsch diesel production. • 200 kW th dual fluidized bed gasifier was integrated with 1 bbl/day F-T synthesis reactor. • Purified syngas satisfies minimum requirements of F-T synthesis. • F-T diesel produced successfully (1 L/h) and satisfies the automotive fuel standard. • Fully integrated BTL system was operated successfully more than 500 h. - Abstract: Fischer–Tropsch (F-T) diesel produced from biomass through gasification is a promising alternative fuel. In this study, a biomass-to-liquid (BTL) system involving a dual fluidized bed gasifier (DFBG), a methanol absorption tower, and an F-T synthesis process was investigated for producing clean biodiesel as an automotive fuel. A DFBG, which is an efficient indirect gasifier, can produce syngas with high caloric value while minimizing the amount of nitrogen in the product gas. In order to meet the strict requirements of syngas for F-T synthesis, any contaminants in the syngas must be minimized and its composition must be carefully controlled. In this work, the syngas mainly comprised 35 vol% of H 2 and 21.3 vol% of CO. The concentrations of H 2 S and COS in the syngas were less than 1 ppmV owing to the use of chilled methanol cleaning process. Furthermore, long-term operation of a fully integrated BTL system was successfully conducted for over 500 h. The results showed that the BTL diesel can be used as an alternative automotive diesel fuel.

  7. Development of a Hybrid Compressor/Expander Module for Automotive Fuel Cell Applications

    Energy Technology Data Exchange (ETDEWEB)

    McTaggart, Paul

    2004-12-31

    In this program TIAX LLC conducted the development of an advanced technology compressor/expander for supplying compressed air to Proton Exchange Membrane (PEM) fuel cells in transportation applications. The overall objective of this program was to develop a hybrid compressor/expander module, based on both scroll and high-speed turbomachinery technologies, which will combine the strengths of each technology to create a concept with superior performance at minimal size and cost. The resulting system was expected to have efficiency and pressure delivery capability comparable to that of a scroll-only machine, at significantly reduced system size and weight when compared to scroll-only designs. Based on the results of detailed designs and analyses of the critical system elements, the Hybrid Compressor/Expander Module concept was projected to deliver significant improvements in weight, volume and manufacturing cost relative to previous generation systems.

  8. CFD simulation of flow-pressure characteristics of a pressure control valve for automotive fuel supply system

    International Nuclear Information System (INIS)

    Wu, Dazhuan; Li, Shiyang; Wu, Peng

    2015-01-01

    Highlights: • Direct CFD method for flow-pressure characteristic of a pressure control valve. • Fitted and interpreted the constants of the spool hydraulic force equation. • Established a flow coefficient function of both valve opening and pressure drop. • Developed an indirect CFD method based on the valve-governing equations. - Abstract: This study aims to elaborate on specific computational fluid dynamics (CFD) simulation methods for fitting the flow-pressure curve of a pressure control valve, which is spring-load valve widely used in the automotive fuel supply system. Given that the couple mechanism exists between the flow field in the valve and the spring system, numerous researchers chose to fit the characteristic curve with experimental approaches but scarcely focused on CFD methods. A direct CFD method is introduced in this study to solve this problem. Two evaluation criteria are used to determine whether the internal flow is physically real. An experiment is conducted to verify the simulation results, and the accuracy of this CFD method is proved. However, it is designed to solve one operating condition with fixed spring parameters and the accuracy depends on the amount of operating conditions. Thus, an indirect CFD method is developed based on the well-elaborated valve-governing equations to improve the efficiency and broaden the application extension. This method aims to simulate the exact value of the equation constants to uncouple the flow by numerical method. It is capable of dealing with changed operating conditions and varied spring parameters, and the results are also verified. The visualization of the internal flow provides a better understanding of the flow fields in the valve. The valve gap directly influences the hydraulic force distribution on the spool and causes most pressure loss. The physical meaning of the function constants are explained based on the flow analysis

  9. Status and Outlook for the U.S. Non-Automotive Fuel Cell Industry: Impacts of Government Policies and Assessment of Future Opportunities

    Energy Technology Data Exchange (ETDEWEB)

    Greene, David L [ORNL; Duleep, K. G. [ICF International; Upreti, Girish [ORNL

    2011-06-01

    Fuel cells (FCs) are considered essential future energy technologies by developed and developing economies alike. Several countries, including the United States, Japan, Germany, and South Korea have established publicly funded R&D and market transformation programs to develop viable domestic FC industries for both automotive and non-automotive applications. Important non-automotive applications include large scale and small scale distributed combined heat and electrical power, backup and uninterruptible power, material handling and auxiliary power units. The U.S. FC industry is in the early stages of development, and is working to establish sustainable markets in all these areas. To be successful, manufacturers must reduce costs, improve performance, and overcome market barriers to new technologies. U.S. policies are assisting via research and development, tax credits and government-only and government-assisted procurements. Over the past three years, the industry has made remarkable progress, bringing both stack and system costs down by more than a factor of two while improving durability and efficiency, thanks in part to government support. Today, FCs are still not yet able to compete in these markets without continued policy support. However, continuation or enhancement of current policies, such as the investment tax credit and government procurements, together with continued progress by the industry, appears likely to establish a viable domestic industry within the next decade.

  10. Research report for fiscal 1998. Research into the trends of low-carbon automotive fuel manufacturing technologies; 1998 nendo jidoshayo teitanso nenryo no seizo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Studies are made of optimum materials and methods for manufacturing low-carbon fuels for reduction in greenhouse gas emissions. When their thermal dynamic limits and the technological maturity are considered, it is inferred that no extensive improvement will be achieved by merely improving on the efficiency of the existing fuels. The use of various high-efficiency driving power sources utterly different in mechanism from the conventional ones, such as those for fuel cell-powered automobiles, and the promotion of the use of low-carbon fuels such as methanol and methane for all kinds of driving power sources including those for the said fuel cell-powered automobiles, will become necessary. The use will also be necessary of recyclable materials. The biomass resources, in particular, since they absorb CO2 gas in their growing process by virtue of photosynthesis, may be said to be free of CO2 gas emissions. They have their own problems, however, which involve the economy of energy consumed for their production, harvesting, transportation, and conversion into fuels. It is therefore required that their whole life cycle be studied before their greenhouse gas reduction effect may be correctly assessed. The quantities of resources available for the production of automotive low-carbon fuels, manufacturing technologies, etc., are first of all put in order for easy perusal. An effective way is assessed for the whole including the life cycle. (NEDO)

  11. Life-cycle analysis of energy and greenhouse gas emissions of automotive fuels in India: Part 1 – Tank-to-Wheel analysis

    International Nuclear Information System (INIS)

    Gupta, S.; Patil, V.; Himabindu, M.; Ravikrishna, R.V.

    2016-01-01

    As part of a two-part life cycle efficiency and greenhouse gas emission analysis for various automotive fuels in the Indian context, this paper presents the first part, i.e., Tank-to-Wheel analysis of various fuel/powertrain configurations for a subcompact passenger car. The Tank-to-Wheel analysis was applied to 28 fuel/powertrain configurations using fuels such as gasoline, diesel, compressed natural gas, liquefied petroleum gas and hydrogen with various conventional and hybrid electric powertrains. The gasoline-equivalent fuel economy and carbon dioxide emission results for individual fuel/powertrain configuration are evaluated and compared. It is found that the split hybrid configuration is best among hybrids as it leads to fuel economy improvement and carbon dioxide emissions reduction by 20–40% over the Indian drive cycle. Further, the engine efficiency, engine on-off time and regenerative braking energy assessment is done to evaluate the causes for higher energy efficiency of hybrid electric vehicles. The hybridization increases average engine efficiency by 10–60% which includes 19–23% of energy recovered at wheel through regenerative braking over the drive cycle. Overall, the Tank-to-Wheel energy use and efficiency results are evaluated for all fuel/powertrain configurations which show Battery Electric Vehicle, fuel cell vehicles and diesel hybrids are near and long term energy efficient vehicle configurations. - Highlights: • Tank-to-Wheel energy use & CO 2 emissions for subcompact car on Indian driving cycle. • Gasoline, diesel, CNG, LPG, hydrogen and electric vehicles are evaluated in this study. • First comprehensive Tank-to-Wheel analysis for India on small passenger car platform. • Parallel, series and split hybrid electric vehicles with various fuels are analysed.

  12. The European automotive LPG market

    International Nuclear Information System (INIS)

    Anon.

    1998-01-01

    The European automotive LPG market could reach at least 4 % of the European fuel market in 2005 versus 1 % in 1990. This would represent a rise of about 35 % in automotive LPG sales (from 2,4 million tonnes in 1997 to 7 million tonnes estimated for 2005). This was underlined by Alain Deleuse, Primagaz group's Marketing Director, in the paper he delivered at the AEGPL Budapest Convention. We publish large excepts of this paper. (author)

  13. Efficiency Standard in automotive industry

    International Nuclear Information System (INIS)

    Goldoni, G.

    2008-01-01

    A technological transition in the transport sector could be only be possible with a convergence of objectives of the automotive and the fuel industries, which is not very simple to obtain. Fuel economy standards could differently reduce the growing trend of CO 2 emissions in this sector but regulators should avoid capture from domestic industry. [it

  14. Recommended composition/property relationships for the characterization of commercial biodiesels before their application in production of automotive diesel fuels in a refinery

    Energy Technology Data Exchange (ETDEWEB)

    Marinov, I.; Stratiev, D.; Shishkova, I.; Dinkov, R. [LUKOIL Neftohim Burgas (Bulgaria); Georgiev, K. [Cristal Chemical Trading, Velingrad (Bulgaria)

    2013-10-15

    The article summarizes the results of experimental studies on the physicochemical properties of twenty commercial biodiesel samples obtained from different manufacturers, and studied properties include density, viscosity and cetane number. An extensive literature review was carried out on available mathematical relationships between fatty acid composition of the biodiesel and the above properties. The predictive potential of the published relationships was evaluated with respect to the properties of the investigated biodiesel samples. Based on existing standard methods for analysis those relationships were selected that fit within the reproducibility of the corresponding method or closely match it. The selected dependencies were summarized in a single mathematical apparatus, with which it is possible to expertly assess the quality of biodiesel before being used for production of automotive diesel fuel in a refinery. (orig.)

  15. Automotive websites

    CERN Document Server

    Jensen, Todd A

    2006-01-01

    For anyone buying a new car, restoring an old favorite, collecting license plates or looking for motorsports information, the internet is the place to go and this is the book to help you get there. Now with over 650 internet addresses, this expanded and updated guide provides detailed descriptions and reviews of the biggest, best and most interesting automotive websites on the net. Beginning with a brief internet history and helpful hints, it aids the novice (or not so novice) user in picking through the countless automotive sites on the internet. Websites are arranged by topics such as afterm

  16. Automotive Mechanics.

    Science.gov (United States)

    Linder, Ralph C.; And Others

    This curriculum guide, which was validated by vocational teachers and mechanics in the field, describes the competencies needed by entry-level automotive mechanics. This guide lists 15 competencies; for each competency, various tasks with their performance objective, student learning experiences, suggested instructional techniques, instructional…

  17. Exhaust gas emissions from various automotive fuels for light-duty vehicles. Effects on health, environment and energy utilization

    International Nuclear Information System (INIS)

    Ahlvik, P.; Brandberg, Aa.

    1999-12-01

    The main aim of the investigation has been to assess the effects on health and environment from various alternative fuels for light-duty vehicles. Effects that can be identified and quantified, such as acidification, ozone formation, cancer risk and climate change, have been of primary interest but other effects, such as respiratory diseases, have also been investigated. Data have been collected through literature surveys for subsequent calculation of the mentioned effects in different time-frames. Corrections have been used to take into consideration the influence of climate, ageing and driving pattern. Emissions generated in fuel production have also been accounted for. The most significant and important differences between the fuels have been found for effects as ozone formation cancer risk and particulate emissions. Alternative fuels, such as methanol and methane (natural gas and biogas), significantly decrease the ozone formation in comparison to petrol, while ethanol, methanol and methane are advantageous concerning cancer risk. The particulate emissions are considerably higher for diesel engines fuelled by diesel oil and RME in comparison to the other fuels. In the future, the importance of acid emissions in the fuel production will increase since the NO x and SO x emissions will decrease from the vehicles. The emissions of climate gases could be significantly reduced by using non-fossil fuels but the efficiency of the drive train is also of importance. The technical development potential for further emission reductions is considerable for all fuels but the advantage for the best fuel options will remain in the future

  18. Understanding the formative stage of technological innovation system development: The case of natural gas as an automotive fuel

    International Nuclear Information System (INIS)

    Suurs, Roald A.A.; Hekkert, Marko P.; Kieboom, Sander; Smits, Ruud E.H.M.

    2010-01-01

    This study contributes to insights into mechanisms that influence the successes and failures of emerging energy technologies. It is assumed that for an emerging technology to fruitfully develop, it should be fostered by a Technological Innovation System (TIS), which is the network of actors, institutions and technologies in which it is embedded. For an emerging technology a TIS has yet to be built up. This research focuses on the dynamics of this build-up process by mapping the development of seven key activities: so-called system functions. The main contribution revolves around the notion of cumulative causation, or the phenomenon that the build-up of a TIS accelerates due to system functions reinforcing each other over time. As an empirical basis, an analysis is provided of the historical development of the TIS around automotive natural gas technology in the Netherlands (1970-2007). The results show that this TIS undergoes a gradual build-up in the 1970s, followed by a breakdown in the 1980s and, again, a build-up from 2000 to 2007. It is shown that underlying these trends are different forms of cumulative causation, here called motors of innovation. The study provides strategic insights for practitioners that aspire to support such motors of innovation.

  19. Final report: U.S. competitive position in automotive technologies

    Energy Technology Data Exchange (ETDEWEB)

    Albert, Michael B.; Cheney, Margaret; Thomas, Patrick; Kroll, Peter

    2002-09-30

    Patent data are presented and analyzed to assess the U.S. competitive position in eleven advanced automotive technology categories, including automotive fuel cells, hydrogen storage, advanced batteries, hybrid electric vehicles and others. Inventive activity in most of the technologies is found to be growing at a rapid pace, particularly in advanced batteries, automotive fuel cells and ultracapacitors. The U.S. is the clear leader in automotive fuel cells, on-board hydrogen storage and light weight materials. Japan leads in advanced batteries, hybrid electric vehicles, ultracapacitors, and appears to be close to overtaking the U.S. in other areas of power electronics.

  20. Automotive sensors

    Science.gov (United States)

    Marek, Jiri; Illing, Matthias

    2003-01-01

    Sensors are an essential component of most electronic systems in the car. They deliver input parameters for comfort features, engine and emission control as well as for the active and passive safety systems. New technologies such as silicon micromachining play an important role for the introduction of these sensors in all vehicle classes. The importance and use of these sensor technologies in today"s automotive applications will be shown in this article. Finally an outlook on important current developments and new functions in the car will be given.

  1. Thermodynamic analysis of a fuel-cell-system for automotive transportation; Thermodynamische Analyse eines Brennstoffzellensystems zum Antrieb von Kraftfahrzeugen

    Energy Technology Data Exchange (ETDEWEB)

    Berger, Oliver

    2009-09-28

    The focus of the investigations was on the cooling of the fuel cell stack module. The many interfaces between the cooling system and other systems (hydrogen and air supply) made it necessary to take a more comprehensive approach. A commercial fuel cell vehicle was used for the investigations. In the first step, experiments were made on system test stands and in the climate wind tunnel. The measured data presented a picture of the status and helped to define the limits of heat transfer to the environment via the fuel cell cooling system. They were also used for validating a dynamic cooling system validation model. With this model, sensitivity analyses were carried out to define the key influencing parameters for increasing the heat transfer to the environment. Optimizations were made in terms of connection of the system component and their design and placement in the front part of the vehicle. On the basis of these and other findings, the optimized aggregate was again investigated on a system test stand in order to obtain more general energetic and exergetic information in the form of Sankey diagrams for visualization of the energy and exergy flows. The stack module under investigation had an efficiency of 61 percent in the test conditions while the aggregate efficiency in consideration of all auxiliary loads was 54 percent. Exergy losses were mostly caused by the fuel cell stack module, the humidifier and the air compressor. Further optimization potential was identified in the utilization of the exhaust exergy which amounts to about 7.3 percent of the fuel exergy. After integration of the fuel cell aggregate in a new vehicel, the new vehicle was again tested in the wind tunnel in order to validate the optimization measures on the cooling system side. For this, the two fuel cell vehicles were compared using the so-called Grossglockner driving cycle which is a test procedure for cooling systems of serially produced vehicles. According to the specifications, the real

  2. Alternative route for the MDW project for automotive fuels in the Dutch highway sector. A legal analysis

    International Nuclear Information System (INIS)

    Van Haute, J.S.R.; Kooy, J.

    2002-01-01

    In February 1998, the Dutch Government initiated an MDW project ('Marktwerking, Deregulering en Wetgevingskwaliteit', i.e. market functioning, deregulation and quality of legislation) to review ways in which competition within the motorway segment of the Dutch retail fuel market could be improved. The project reviewed the entry barriers and considered ways to stimulate competition, including preferential treatment of new entrants. The Dutch Major oil companies protested against the original plans of the Government and announced legal proceedings. The Government agreed to engage in negotiations with the oil industry in order to reach a compromise solution and avoid a legal battle. This resulted in an alternative route, which is analyzed in this article from a legal perspective [nl

  3. Part II: Oxidative Thermal Aging of Pd/Al2O3 and Pd/CexOy-ZrO2 in Automotive Three Way Catalysts: The Effects of Fuel Shutoff and Attempted Fuel Rich Regeneration

    Directory of Open Access Journals (Sweden)

    Qinghe Zheng

    2015-10-01

    Full Text Available The Pd component in the automotive three way catalyst (TWC experiences deactivation during fuel shutoff, a process employed by automobile companies for enhancing fuel economy when the vehicle is coasting downhill. The process exposes the TWC to a severe oxidative aging environment with the flow of hot (800 °C–1050 °C air. Simulated fuel shutoff aging at 1050 °C leads to Pd metal sintering, the main cause of irreversible deactivation of 3% Pd/Al2O3 and 3% Pd/CexOy-ZrO2 (CZO as model catalysts. The effect on the Rh component was presented in our companion paper Part I. Moderate support sintering and Pd-CexOy interactions were also experienced upon aging, but had a minimal effect on the catalyst activity losses. Cooling in air, following aging, was not able to reverse the metallic Pd sintering by re-dispersing to PdO. Unlike the aged Rh-TWCs (Part I, reduction via in situ steam reforming (SR of exhaust HCs was not effective in reversing the deactivation of aged Pd/Al2O3, but did show a slight recovery of the Pd activity when CZO was the carrier. The Pd+/Pd0 and Ce3+/Ce4+ couples in Pd/CZO are reported to promote the catalytic SR by improving the redox efficiency during the regeneration, while no such promoting effect was observed for Pd/Al2O3. A suggestion is made for improving the catalyst performance.

  4. New insights to the use of ethanol in automotive fuels: a stable isotopic tracer for fossil- and bio-fuel combustion inputs to the atmosphere.

    Science.gov (United States)

    Giebel, Brian M; Swart, Peter K; Riemer, Daniel D

    2011-08-01

    Ethanol is currently receiving increased attention because of its use as a biofuel or fuel additive and because of its influence on air quality. We used stable isotopic ratio measurements of (13)C/(12)C in ethanol emitted from vehicles and a small group of tropical plants to establish ethanol's δ(13)C end-member signatures. Ethanol emitted in exhaust is distinctly different from that emitted by tropical plants and can serve as a unique stable isotopic tracer for transportation-related inputs to the atmosphere. Ethanol's unique isotopic signature in fuel is related to corn, a C4 plant and the primary source of ethanol in the U.S. We estimated a kinetic isotope effect (KIE) for ethanol's oxidative loss in the atmosphere and used previous assumptions with respect to the fractionation that may occur during wet and dry deposition. A small number of interpretive model calculations were used for source apportionment of ethanol and to understand the associated effects resulting from atmospheric removal. The models incorporated our end-member signatures and ambient measurements of ethanol, known or estimated source strengths and removal magnitudes, and estimated KIEs associated with atmospheric removal processes for ethanol. We compared transportation-related ethanol signatures to those from biogenic sources and used a set of ambient measurements to apportion each source contribution in Miami, Florida-a moderately polluted, but well ventilated urban location.

  5. Automotive electronics

    Energy Technology Data Exchange (ETDEWEB)

    Basshuysen, R. van [ed.; Baun, R. [comp.

    2000-10-01

    Electronic equipment is indispensable in modern motor cars for active and passive safety, exhaust and consumption monitoring or comfort. Electric and electronic systems today account for nearly 20 percent of the production cost of a normal passenger car, with an upward trend. Infotainment equipment is a growing market, which gets center stage in this issue. Further subjects discussed are current electronic and mechatronic applications as well as new developments in data transmission, development tools and constructional elements. [German] Ohne Elektronik sind moderne Automobile nicht mehr vorstellbar. Ob aktive oder passive Sicherheit, Abgas, Verbrauch oder Komfort - der Fortschritt im Autombil ist eng verknuepft mit der Einfuehrung neuer elektronischer Systeme und Komponenten. Obwohl meist nicht sehr auffaellig in einer Black-box verpackt, liegen die anteiligen Herstellungskosten fuer die Elektrik und Elektronik bei einem Mittelklassefahrzeug schon bei knapp 20 Prozent. Tendenz: Weiter steigend. Waehrend die Segnungen von ABS, ESP oder Motormanagement fuer den Kunden unsichtbar bleiben, tritt die Elektronik mit den Infotainment-Systemen ins Rampenlicht. Hochwertige Audio-Anlagen im Doppel-DIN-Format und grosse Farbbildschirme sitzen an prominenter Stelle im Armaturenbrett. Elektronische Systeme werden damit fuer den Kunden sichtbar, greifbar und erlebbar. Doch je mehr Funktionen integriert werden, desto wichtiger wird eine einfache Bedienung, die den Fahrer moeglichst wenig vom Verkehrsgeschehen ablenkt. Das ist leider keine Selbstverstaendlichkeit: Eine klare, einfache Bedienung wurde in der Vergangenheit schon bei so manchem simplen Cassetten-Radio schmerzlich vermisst. Infotainment im Automobil ist ein Wachstumsmarkt - und das Schwerpunkt-Thema der vorliegenden zweiten Ausgabe von 'Automotive Electronics'. Darueber hinaus beschaeftigt sich auch diese Ausgabe mit aktuellen Elektronik- und Mechatronik-Anwendungen und berichtet ueber neue Entwicklungen

  6. Status and Prospects of the Global Automotive Fuel Cell Industry and Plans for Deployment of Fuel Cell Vehicles and Hydrogen Refueling Infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Greene, David L [ORNL; Duleep, Gopal [HD Systems

    2013-06-01

    Automobile manufacturers leading the development of mass-market fuel cell vehicles (FCVs) were interviewed in Japan, Korea, Germany and the United States. There is general agreement that the performance of FCVs with respect to durability, cold start, packaging, acceleration, refueling time and range has progressed to the point where vehicles that could be brought to market in 2015 will satisfy customer expectations. However, cost and the lack of refueling infrastructure remain significant barriers. Costs have been dramatically reduced over the past decade, yet are still about twice what appears to be needed for sustainable market success. While all four countries have plans for the early deployment of hydrogen refueling infrastructure, the roles of government, industry and the public in creating a viable hydrogen refueling infrastructure remain unresolved. The existence of an adequate refueling infrastructure and supporting government policies are likely to be the critical factors that determine when and where hydrogen FCVs are brought to market.

  7. Automotive vehicle sensors

    Energy Technology Data Exchange (ETDEWEB)

    Sheen, S.H.; Raptis, A.C.; Moscynski, M.J.

    1995-09-01

    This report is an introduction to the field of automotive vehicle sensors. It contains a prototype data base for companies working in automotive vehicle sensors, as well as a prototype data base for automotive vehicle sensors. A market analysis is also included.

  8. General Mechanical Repair. Minor Automotive Maintenance. Volume 1. Teacher's Guide.

    Science.gov (United States)

    East Texas State Univ., Commerce. Occupational Curriculum Lab.

    Fourteen units on minor automotive maintenance are presented in this teacher's guide. The units are the following: introduction to minor automotive maintenance, shop safety, engine principles, fuel system operation and repair, electrical system, ignition system, lubrication system, engine cooling system, exhaust system, wheel bearings and tires,…

  9. Les nouveaux carburants pour l'automobile. Carburants oxygénés : emploi et émissions New Automotive Fuels. Oxygenated Fuels: Their Use and Emissions

    Directory of Open Access Journals (Sweden)

    Guibet J. C.

    2006-11-01

    Full Text Available A la lumière de résultats nouveaux obtenus à l'IFP et de publications récentes sur le sujet, on étudie les principales répercussions de l'emploi de carburants oxygénés sur les émissions de polluants à l'échapement et sur les risques possibles associés à la manipulation des produits. Les polluants examinés sont les alkyles de plomb, l'oxyde de carbone, les oxydes d'azote, les produits imbrûlés, les aldéhydes et les hydrocarbures aromatiques polynucléaires. Les émissions de fumées et de particules solides par les moteurs diesel font aussi l'objet de quelques commentaires. On aborde également les problèmes de pertes par évaporation et on fournit quelques informations sur la toxicité des alcools et des aldéhydes. L'étude fait apparaître un besoin réel de nouvelles recherches dans le domaine, mais elle indique déjà que l'emploi de produits organiques oxygénés comme carburants ne devrait pas changer l'ordre de grandeur des niveaux de polluants. In the light of new results from IFP and recent publications on the subject, this article examines the main repercussions of the use of oxygenated fuelss on pollutant exhauts emissions and on possible risks associated with the handling of products. The pollutants examined are lead alkyls, carbon monoxide, nitrogen oxides, unburned products, aldehydes and polynuclear aromatic hydrocarbons. Emissions of smoke and solid particles by diesel engines are also the subject of various comments. Likewise, the article takes up the problem of losses by evaporation, and some information is provided on the toxicity of alcohols and aldehydes. This study reveals the real need for further research in the field, but it already shows that the use of oxygenated organic products as fuels should not bring about much change in the order of magnitude of pollutant levels.

  10. Degradation of automotive materials in palm biodiesel

    International Nuclear Information System (INIS)

    Fazal, M.A.; Haseeb, A.S.M.A.; Masjuki, H.H.

    2012-01-01

    As compared to petroleum diesel, biodiesel is more corrosive for automotive materials. Studies on the characterization of corrosion products of fuel exposed automotive materials are scarce. Automotive fuel system and engine components are made from different ferrous and non-ferrous materials. The present study aims to investigate the corrosion products of different types of automotive materials such as copper, brass, aluminum and cast iron upon exposure to diesel and palm biodiesel. Changes in fuel properties due to exposure of different materials were also examined. Degradation of metal surface was characterized by digital camera, SEM/EDS and X-ray diffraction (XRD). Fuel properties were examined by measuring TAN (total acid number), density and viscosity. Among the metal investigated, copper is found to be least resistant in biodiesel and formed comparatively more corrosion products than other metals. Upon exposure of metals in biodiesel, TAN number crosses the limit given by standard while density and viscosity remain within the acceptable range of limit. -- Highlights: ► Order of incompatible metals in palm biodiesel: copper > brass > aluminum > cast iron. ► The possible reactions for the degradation of copper and cast iron have been discussed. ► For metal exposed biodiesel, only TAN number crosses the limit while density and viscosity remain within the limit. ► Copper and copper based alloy (brass) increase TAN number comparatively more than other metals.

  11. Environmental Innovation Dynamics in the Automotive industry

    NARCIS (Netherlands)

    Kuik, O

    2006-01-01

    This paper addresses the innovation dynamics induced by environmental policy in the automotive industry. It examines car fuel efficiency programs in the EU, the US and Japan. It concludes that existing programs have not yet succeeded in promoting radical and breakthrough technologies, but that, at

  12. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXII, I--MAINTAINING THE FUEL SYSTEM (PART I)--CUMMINS DIESEL ENGINE, II--UNDERSTANDING THE DIFFERENTIAL.

    Science.gov (United States)

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE FUNCTION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM AND DIFFERENTIAL DRIVE UNITS USED IN DIESEL POWERED VEHICLES. TOPICS ARE (1) FUEL SYSTEM COMPARISONS, (2) FUEL SYSTEM SUPPLY COMPONENTS, (3) FUEL SUPPLY SECTION MAINTENANCE, (4) FUNCTION OF THE DIFFERENTIAL,…

  13. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XIII, I--MAINTAINING THE FUEL SYSTEM (PART III), CUMMINS DIESEL ENGINES, II--RADIATOR SHUTTER SYSTEM.

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE CONSTRUCTION, OPERATION, AND MAINTENANCE OF THE DIESEL ENGINE FUEL AND RADIATOR SHUTTER SYSTEMS. TOPICS ARE (1) MORE ABOUT THE CUMMINS FUEL SYSTEM, (2) CALIBRATING THE PT FUEL PUMP, (3) CALIBRATING THE FUEL INJECTORS, (4) UNDERSTANDING THE SHUTTER SYSTEM, (5) THE…

  14. Recycling of automotive aluminum

    OpenAIRE

    Cui, Jirang; Roven, Hans Jørgen

    2010-01-01

    With the global warming of concern, the secondary aluminum stream is becoming an even more important component of aluminum production and is attractive because of its economic and environmental benefits. In this work, recycling of automotive aluminum is reviewed to highlight environmental benefits of aluminum recycling, use of aluminum alloys in automotive applications, automotive recycling process, and new technologies in aluminum scrap process. Literature survey shows that newly developed t...

  15. Modern materials for automotive industry

    Directory of Open Access Journals (Sweden)

    Hovorun T. P.

    2017-12-01

    Full Text Available The car industry uses a tremendous number of materials to build cars, including iron, aluminum, steel, glass, rubber, petroleum products, copper, steel and others. These materials have evolved greatly over the decades, becoming more sophisticated, better built, and safer. They've changed as new automotive manufacturing technologies have emerged over the years, and they're used in increasingly innovative ways. This article is devoted to systematization information on the introduction and application of modern materials in the automotive industry. Given both domestic and foreign sources of information, it follows that car manufacturers are constantly pushing to create the lightest cars possible to increase speed and power. Research and development into lightweight materials is essential for lowering their cost, increasing their ability to be recycled, enabling their integration into vehicles, and maximizing their fuel economy benefits. Light weighting without loss of strength and speed properties is the present, and the future, of the automotive manufacturing industry. It brings innovative materials to the frontline of design.

  16. Automotive Thermoelectric Waste Heat Recovery

    Science.gov (United States)

    Meisner, Gregory P.

    2015-03-01

    Considerable fuel energy, as much as 70%, is not converted to useful work by internal combustion engines but is instead rejected as waste heat, and more than half of the waste heat, nearly 40% of fuel energy, is contained in vehicle exhaust gas. This provides an opportunity to recover some of the wasted fuel energy and convert it from heat into useful work, subject to the laws of thermodynamics, and thereby improve vehicle energy efficiency. Thermoelectric (TE) materials have been extensively researched and TE devices are now being developed for operation at high temperatures corresponding to automotive exhaust gases for direct solid-state conversion of heat into electricity. This has stimulated substantial progress in the development of practical TE generator (TEG) systems for large-scale commercialization. A significant enabler of this progress has been the US Department of Energy's Vehicle Technologies Program through funding for low cost solutions for automotive TE waste heat recovery to improve fuel economy. Our current project at General Motors has culminated in the identification of the potential supply chain for all components and assembly of an automotive TEG. A significant focus has been to develop integrated and iterative modeling tools for a fully optimized TEG design that includes all components and subsystems (TE modules, heat exchangers, thermal interfaces, electrical interconnects, power conditioning, and vehicle integration for maximal use of TEG power). We have built and tested a new, low-cost Initial TEG prototype based on state-of-the-art production-scale skutterudite TE modules, novel heat exchanger designs, and practical solutions to the many technical challenges for optimum TEG performance. We will use the results for our Initial TEG prototype to refine our modeling and design tools for a Final automotive TEG system prototype. Our recent results will be presented. Thanks to: J.R. Salvador, E.R. Gundlach, D. Thompson, N.K. Bucknor, M

  17. Automotive Technology Skill Standards

    Science.gov (United States)

    Garrett, Tom; Asay, Don; Evans, Richard; Barbie, Bill; Herdener, John; Teague, Todd; Allen, Scott; Benshoof, James

    2009-01-01

    The standards in this document are for Automotive Technology programs and are designed to clearly state what the student should know and be able to do upon completion of an advanced high-school automotive program. Minimally, the student will complete a three-year program to achieve all standards. Although these exit-level standards are designed…

  18. Automotive Industry in Malaysia

    DEFF Research Database (Denmark)

    Wad, Peter; Govindaraju, V.G.R. Chandran

    2011-01-01

    This paper explains the evolution and assesses the development of the Malaysian automotive industry within the premise of infant industry and trade protection framework as well as extended arguments of infant industry using a global value chain perspective. The Malaysian automotive industry...

  19. The Evaluation of Flash Point and Cold Filter Plugging Point with Blends of Diesel and Cyn-Diesel Pyrolysis Fuel for Automotive Engines

    OpenAIRE

    Murphy, Fionnuala; Devlin, Ger; McDonnell, Kevin

    2013-01-01

    The production of synthetic fuels from alternative sources has increased in recent years as a cleaner, more sustainable source of transport fuel is now required. The European Commission has outlined renewable energy targets pertaining to transport fuel which must be met by 2020. In response to these targets Ireland has committed, through the Biofuels Obligation Scheme of 2008, to producing 3% of transport fuels from biofuels by 2010 and 10% by 2020. In order to be suitable for sale in Europe,...

  20. AUTOMOTIVE DIESEL MAINTENANCE L. UNIT XII, PART I--MAINTAINING THE FUEL SYSTEM (PART II), CUMMINS DIESEL ENGINE, PART II--UNIT INSTALLATION (ENGINE).

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM AND THE PROCEDURES FOR DIESEL ENGINE INSTALLATION. TOPICS ARE FUEL FLOW CHARACTERISTICS, PTG FUEL PUMP, PREPARATION FOR INSTALLATION, AND INSTALLING ENGINE. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH…

  1. Automotive electronics design fundamentals

    CERN Document Server

    Zaman, Najamuz

    2015-01-01

    This book explains the topology behind automotive electronics architectures and examines how they can be profoundly augmented with embedded controllers. These controllers serve as the core building blocks of today’s vehicle electronics. Rather than simply teaching electrical basics, this unique resource focuses on the fundamental concepts of vehicle electronics architecture, and details the wide variety of Electronic Control Modules (ECMs) that enable the increasingly sophisticated "bells & whistles" of modern designs.  A must-have for automotive design engineers, technicians working in automotive electronics repair centers and students taking automotive electronics courses, this guide bridges the gap between academic instruction and industry practice with clear, concise advice on how to design and optimize automotive electronics with embedded controllers.

  2. Optimization and optimal control in automotive systems

    CERN Document Server

    Kolmanovsky, Ilya; Steinbuch, Maarten; Re, Luigi

    2014-01-01

    This book demonstrates the use of the optimization techniques that are becoming essential to meet the increasing stringency and variety of requirements for automotive systems. It shows the reader how to move away from earlier  approaches, based on some degree of heuristics, to the use of  more and more common systematic methods. Even systematic methods can be developed and applied in a large number of forms so the text collects contributions from across the theory, methods and real-world automotive applications of optimization. Greater fuel economy, significant reductions in permissible emissions, new drivability requirements and the generally increasing complexity of automotive systems are among the criteria that the contributing authors set themselves to meet. In many cases multiple and often conflicting requirements give rise to multi-objective constrained optimization problems which are also considered. Some of these problems fall into the domain of the traditional multi-disciplinary optimization applie...

  3. Experimental investigations and guidelines for PCB design for a fuel injection ECU to meet automotive environmental, EMI/EMC and ESD standards

    Science.gov (United States)

    Kalyankar-Narwade, Supriya; Kumar, C. Ramesh; Patil, Sanjay A.

    2017-11-01

    Engine Management ECU plays a vital role in controlling different important features related to the engine performance. ECU is an embedded system which includes hardware and firmware platform for control logics. However, it is necessary to verify its smooth performance by its functionality testing in the Electromagnetic environment for approval. If these requirements are not known at earlier stages, then ECU may not fulfil functional requirements during required automotive electronic test standards. Hence, focusing on EMS ECU, this paper highlights hardware, layout and software guidelines for solving problems related with Electromagnetic Interference (EMI) to comply ISO 7637, CISPR 25 standard, Electromagnetic Compatibility (EMC) to comply ISO 11452-4,5 standard, Electrostatic Discharge (ESD) to comply ISO 10605 standard and Environmental Testing to comply standards as per IEC standards. This paper specifies initially the importance, need and guidelines for reducing the EMI effect on PCB i.e. making ECU more electromagnetically compatible as per automotive standards. The guidelines are useful for the designers to avoid pitfalls at the later stage. After mentioned modifications in the paper, ECU successfully passed the requirements for all standard tests.

  4. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXIV, I--MAINTAINING THE FUEL SYSTEM PART III--CATERPILLAR DIESEL ENGINE, II--UNDERSTANDING THE VOLTAGE REGULATOR/ALTERNATOR.

    Science.gov (United States)

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL AND BATTERY CHARGING SYSTEM. TOPICS ARE (1) INJECTION TIMING CONTROLS, (2) GOVERNOR, (3) FUEL SYSTEM MAINTENANCE TIPS, (4) THE CHARGING SYSTEM, (5) REGULATING THE GENERATOR/ALTERNATOR, AND (6) CHARGING SYSTEM SERVICE…

  5. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXIII, I--MAINTAINING THE FUEL SYSTEM, PART II--CATERPILLAR DIESEL ENGINE, II--UNDERSTANDING STEERING SYSTEMS.

    Science.gov (United States)

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL INJECTION SYSTEM AND THE STEERING SYSTEM OF DIESEL POWERED VEHICLES. TOPICS ARE FUEL INJECTION SECTION, AND DESCRIPTION OF THE STEERING SYSTEM. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING…

  6. National Automotive Center - NAC

    Data.gov (United States)

    Federal Laboratory Consortium — Encouraged by the advantages of collaboration, the U.S. Army Tank Automotive Research, Development and Engineering Center (TARDEC) worked with the Secretary of the...

  7. Advanced materials for application in the aerospace and automotive industries

    CSIR Research Space (South Africa)

    Damm, O

    2008-11-01

    Full Text Available long life. Table 1 lists typical automotive components suitable for forming by SSM (Ivanchev et al. 2008). Table 1: Automotive components suitable for SSM casting 4 Car unit Component Brake system Fuel supply system Engine and suspension... 100 000 t by 2010 [Karus 2004] China and India have recently emerged as major global growth markets, with average annual GDP growth rates of around 11% and 9%, respectively. The huge demand for commodity materials in these economies, as well...

  8. Exhaust gas emissions from various automotive fuels for light-duty vehicles. Effects on health, environment and energy utilization; Avgasemissioner fraan laetta fordon drivna med olika drivmedel

    Energy Technology Data Exchange (ETDEWEB)

    Ahlvik, P.; Brandberg, Aa. [Ecotraffic RandD AB, Stockholm (Sweden)

    1999-12-01

    The main aim of the investigation has been to assess the effects on health and environment from various alternative fuels for light-duty vehicles. Effects that can be identified and quantified, such as acidification, ozone formation, cancer risk and climate change, have been of primary interest but other effects, such as respiratory diseases, have also been investigated. Data have been collected through literature surveys for subsequent calculation of the mentioned effects in different time-frames. Corrections have been used to take into consideration the influence of climate, ageing and driving pattern. Emissions generated in fuel production have also been accounted for. The most significant and important differences between the fuels have been found for effects as ozone formation cancer risk and particulate emissions. Alternative fuels, such as methanol and methane (natural gas and biogas), significantly decrease the ozone formation in comparison to petrol, while ethanol, methanol and methane are advantageous concerning cancer risk. The particulate emissions are considerably higher for diesel engines fuelled by diesel oil and RME in comparison to the other fuels. In the future, the importance of acid emissions in the fuel production will increase since the NO{sub x} and SO{sub x} emissions will decrease from the vehicles. The emissions of climate gases could be significantly reduced by using non-fossil fuels but the efficiency of the drive train is also of importance. The technical development potential for further emission reductions is considerable for all fuels but the advantage for the best fuel options will remain in the future.

  9. Automotive Stirling engine: Mod II design report

    Energy Technology Data Exchange (ETDEWEB)

    Nightingale, N.P.

    1986-10-01

    The design of an automotive Stirling engine that achieves the superior fuel economy potential of the Stirling cycle is described. As the culmination of a 9-yr development program, this engine, designated the Mod II, also nullifies arguments that Stirling engines are heavy, expensive, unreliable, and demonstrate poor performance. Installed in a General Motors 1985 Chevrolet Celebrity car, this engine has a predicted combined fuel economy on unleaded gasoline of 17.5 km/L (41 mi/gal) - a value 50% above the current vehicle fleet average. The Mod II Stirling engine is a four-cylinder V-drive design with a single crankshaft. The engine is also equipped with all the controls and auxiliaries necessary for automotive operation. 35 figs.

  10. L'auto adaptation à des mélanges essence/alcool utilisés comme carburant automobile: le moteur souple The Self-Adapting of Gasoline/Alcohol Mixtures Used As Automotive Fuel: the Flexible Engine

    Directory of Open Access Journals (Sweden)

    Dorbon M.

    2006-11-01

    Full Text Available Le moteur souple est un moteur susceptible d'être alimenté par des carburants constitués de mélanges d'une essence classique et d'un alcool léger (méthanol ou éthanol; si la concentration de chacun des composants de ces mélanges varie, les réglages nécessaires au bon fonctionnement du véhicule se font automatiquement. Dans cet article, sont tout d'abord exposées les propriétés caractéristiques en tant que carburant automobile de l'un de ces alcools légers, le méthanol. Puis viennent les descriptions des dispositifs qui font le moteur souple c'est-à-dire d'une part les systèmes de reconnaissance du carburant et d'autre part les appareillages susceptibles de modifier les réglages du moteur (alimentation et allumage en fonction de la qualité du mélange consommé. A flexible engine is one capable of running on fuels consisting of mixtures of conventional gasoline and a light alcohol (methanol or ethanol. If the concentration of each of these components of such mixtures varies, the tuning required for the proper running of the vehicle takes place automatically. This article begins by describing the characteristic properties of one of these light alcohols (methanol as an automotive fuel. Then the equipment is described that makes an engine flexible, i. e. both the fuel recognition systems and the equipment capable of changing engine tuning (feed and ignition as a function of the quality of the mixture burned.

  11. Future Automotive Systems Technology Simulator (FASTSim)

    Energy Technology Data Exchange (ETDEWEB)

    2018-04-11

    An advanced vehicle powertrain systems analysis tool, the Future Automotive Systems Technology Simulator (FASTSim) provides a simple way to compare powertrains and estimate the impact of technology improvements on light-, medium- and heavy-duty vehicle efficiency, performance, cost, and battery life. Created by the National Renewable Energy Laboratory, FASTSim accommodates a range of vehicle types - including conventional vehicles, electric-drive vehicles, and fuel cell vehicles - and is available for free download in Microsoft Excel and Python formats.

  12. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XI, PART I--MAINTAINING THE FUEL SYSTEM (PART I), CUMMINS DIESEL ENGINES, PART II--UNIT REPLACEMENT (ENGINE).

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF DIFFERENCES BETWEEN TWO AND FOUR CYCLE ENGINES, THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM, AND THE PROCEDURES FOR DIESEL ENGINE REMOVAL. TOPICS ARE (1) REVIEW OF TWO CYCLE AND FOUR CYCLE CONCEPT, (2) SOME BASIC CHARACTERISTICS OF FOUR CYCLE ENGINES,…

  13. AUTOMOTIVE DIESEL MAINTENANCE. PROGRAM OUTLINE.

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    INFORMATIONAL TOPICS COVERED IN THE TEXT MATERIALS AND SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING FILMS FOR A 2-YEAR, 55 MODULE PROGRAM IN AUTOMOTIVE DIESEL MAINTENANCE ARE GIVEN. THE 30 MODULES FOR "AUTOMOTIVE DIESEL MAINTENANCE 1" ARE AVAILABLE AS VT 005 655 - VT 005 684, AND THE 25 MODULES FOR "AUTOMOTIVE DIESEL MAINTENANCE 2" ARE AVAILABLE…

  14. 77 FR 55898 - Request for Comments on a Renewal of a Previously Approved Information Collection: Automotive...

    Science.gov (United States)

    2012-09-11

    ...: Kenneth R. Katz, Fuel Economy Division, Office of International Policy, Fuel Economy and Consumer Programs... Fuel Economy Reports ACTION: Notice and request for comments. SUMMARY: In compliance with the Paperwork... Part 537, Automotive Fuel Economy Reports. OMB Control Number: 2127-0019. Type of Request: Renewal of a...

  15. Automotive NVH technology

    CERN Document Server

    Nijman, Eugenius; Priebsch, Hans-Herwig

    2016-01-01

    This book presents seven chapters examining selected noise, vibration and harshness (NVH) topics that are highly relevant for automotive vehicle development. These include applications following the major trends toward increased passenger comfort, vehicle electrification and lightweight design. The authors of the seven chapters, all of which are experts from the automotive industry and academia, present the foremost challenges and potential solutions in this demanding field. Among others, applications for sound optimization in downsized engines, noise optimization in electric powertrains, weight reduction options for exhaust systems, porous materials description, and the vibro-acoustic analysis of geared systems are discussed.

  16. Identification for automotive systems

    CERN Document Server

    Hjalmarsson, Håkan; Re, Luigi

    2012-01-01

    Increasing complexity and performance and reliability expectations make modeling of automotive system both more difficult and more urgent. Automotive control has slowly evolved from an add-on to classical engine and vehicle design to a key technology to enforce consumption, pollution and safety limits. Modeling, however, is still mainly based on classical methods, even though much progress has been done in the identification community to speed it up and improve it. This book, the product of a workshop of representatives of different communities, offers an insight on how to close the gap and exploit this progress for the next generations of vehicles.

  17. General Mechanical Repair. Minor Automotive Maintenance, Small Engine [Repair, and] Welding: Student Manual.

    Science.gov (United States)

    Hamlin, Larry

    This document is a student manual for a general mechanical repair course. Following a list of common essential elements of trade and industrial education, the manual is divided into three sections. The first section, on minor automotive maintenance, contains 13 units: automotive shop safety; engine principles; fuel system operation and repair;…

  18. Fuel Cell Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Fuel Cell Technical Team promotes the development of a fuel cell power system for an automotive powertrain that meets the U.S. DRIVE Partnership (United States Driving Research and Innovation for Vehicle efficiency and Energy sustainability) goals.

  19. Lightweight Steel Solutions for Automotive Industry

    International Nuclear Information System (INIS)

    Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

    2010-01-01

    Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI is a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.

  20. Ceramic technologies for automotive industry: Current status and perspectives

    International Nuclear Information System (INIS)

    Okada, Akira

    2009-01-01

    The automotive industry has developed substantially through advances in mechanical technologies, and technologies such as electronics and advanced materials have also contributed to further advances in automobiles. The contribution of ceramic materials to automobile technologies ranges over driving performance, exhaust gas purification, and fuel efficiency improvements. Several ceramic components, such as knock sensors, oxygen sensors, exhaust gas catalysts, and silicon nitride parts for automotive engines, have been successfully applied to automobiles. This paper focuses on the contribution of ceramics to automotive technologies. It also mentions potential contributions in the future, including adiabatic turbo-compound diesels, ceramic gas turbines, fuel cells, and electric vehicles because ceramic technologies have been intensively involved in the challenge to achieve advanced power sources.

  1. Rotordynamics of automotive turbochargers

    CERN Document Server

    Nguyen-Schäfer, Hung

    2015-01-01

    Rotordynamics of automotive turbochargers is dealt with in this book encompassing the widely working field of small turbomachines under real operating conditions at the very high rotor speeds up to 300000 rpm. The broadly interdisciplinary field of turbocharger rotordynamics involves 1) Thermodynamics and Turbo-Matching of Turbochargers 2) Dynamics of Turbomachinery 3) Stability Analysis of Linear Rotordynamics with the Eigenvalue Theory 4) Stability Analysis of Nonlinear Rotordynamics with the Bifurcation Theory 5) Bearing Dynamics of the Oil Film using the Two-Phase Reynolds Equation 6) Computation of Nonlinear Responses of a Turbocharger Rotor 7) Aero and Vibroacoustics of Turbochargers 8) Shop and Trim Balancing at Two Planes of the Rotor 9) Tribology of the Bearing Surface Roughness 10) Design of Turbocharger Platforms using the Similarity Laws The rotor response of an automotive turbocharger at high rotor speeds is studied analytically, computationally, and experimentally. Due to the nonlinear character...

  2. PARADOXES OF AUTOMOTIVE EVOLUTION

    Directory of Open Access Journals (Sweden)

    V. A. Grabaurov

    2014-01-01

    Full Text Available The paper presents a historical analysis of tendencies pertaining to automotive evolution. It has been shown how motivation to higher speed and capacity had made it possible to manufacture automobiles with several hundred horsepower capacity. Traffic speed in the cities is rather less than technical capabilities of automobiles; there are serious ecological and traffic safety problems. Solution of serious traffic safety problems is possible only while developing clever automobiles for clever traffic roads within the framework of intelligent transportation systems.

  3. FISITA 2012 World Automotive Congress

    CERN Document Server

    2013-01-01

    Proceedings of the FISITA 2012 World Automotive Congress are selected from nearly 2,000 papers submitted to the 34th FISITA World Automotive Congress, which is held by Society of Automotive Engineers of China (SAE-China ) and the International Federation of Automotive Engineering Societies (FISITA). This proceedings focus on solutions for sustainable mobility in all areas of passenger car, truck and bus transportation. Volume 8: Vehicle Design and Testing (II) focuses on: •Automotive Reliability Technology •Lightweight Design Technology •Design for Recycling •Dynamic Modeling •Simulation and Experimental Validation •Virtual Design, Testing and Validation •Testing of Components, Systems and Full Vehicle Above all researchers, professional engineers and graduates in fields of automotive engineering, mechanical engineering and electronic engineering will benefit from this book.   SAE-China is a national academic organization composed of enterprises and professionals who focus on research, design a...

  4. Get Your Automotive Program Nationally Certified!

    Science.gov (United States)

    Lundquist, Patricia A.

    2000-01-01

    Automotive programs that nationally certified enhance student recruitment and give students better employment opportunities. Technicians who earn the Automotive Service Excellence credential have joined the ranks of professionals in the automotive service industry. (Author/JOW)

  5. Automotive Chassis; Automotive Mechanics-Basic: 9043.02.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    This automotive chassis course is designed to familiarize the beginning student of the history and development of the automobile with basic concepts common to the automobile industry, and general information that is required for successful advancement in the automotive mechanics field. It is one quinmester in a series of quinmester outlines…

  6. Automotive mechatronics automotive networking, driving stability systems, electronics

    CERN Document Server

    2015-01-01

    As the complexity of automotive vehicles increases this book presents operational and practical issues of automotive mechatronics. It is a comprehensive introduction to controlled automotive systems and provides detailed information of sensors for travel, angle, engine speed, vehicle speed, acceleration, pressure, temperature, flow, gas concentration etc. The measurement principles of the different sensor groups are explained and examples to show the measurement principles applied in different types. Contents Basics of mechatronics.- Architecture.- Electronic control unit.- Software development.- Basic principles of networking.- Automotive networking.- Bus systems.- Automotive sensors.- Sensor measuring principles.- Sensor types.- Electric actuators.- Electrohydraulic actuators.- Electronic transmission control.- Electronic transmission control unit.- Modules for transmission control.- Antilock braking system.- Traction control system.- Electronic stability program.- Automatic brake functions.- Hydraulic modu...

  7. Automotive systems engineering

    CERN Document Server

    Winner, Hermann

    2013-01-01

    This book reflects the shift in design paradigm in automobile industry. It presents future innovations, often referred as  “automotive systems engineering”.  These cause fundamental innovations in the field of driver assistance systems and electro-mobility as well as fundamental changes in the architecture of the vehicles. New driving functionalities can only be realized if the software programs of multiple electronic control units work together correctly. This volume presents the new and innovative methods which are mandatory to master the complexity of the vehicle of the future.

  8. Automotive component failures

    CSIR Research Space (South Africa)

    Heyes, AM

    1998-06-01

    Full Text Available [ However\\ in the presence of a stress concentration the ultimate tensile stress can be exceeded before the ultimate shear stress is reached\\ resulting in a tensile failure 0 [ 2[6[ Metallo`raphy and Ener`y Dispersive Spectroscopy "EDS# A microspecimen...\\ Vol[ 4\\ No[ 1\\ pp[ 018 030\\ 0887 0887 Elsevier Science Ltd[ All rights reserved\\ Pergamon Printed in Great Britain 0249 5296:87 ,08[99 9[99 PII] S0249 5296"87#99909 6 AUTOMOTIVE COMPONENT FAILURES A[ M[ HEYES Advanced Engineering and Testing...

  9. The automotive transmission book

    CERN Document Server

    Fischer, Robert; Jürgens, Gunter; Najork, Rolf; Pollak, Burkhard

    2015-01-01

    This book presents essential information on systems and interactions in automotive transmission technology and outlines the methodologies used to analyze and develop transmission concepts and designs. Functions of and interactions between components and subassemblies of transmissions are introduced, providing a basis for designing transmission systems and for determining their potentials and properties in vehicle-specific applications: passenger cars, trucks, buses, tractors, and motorcycles. With these fundamentals the presentation provides universal resources for both state-of-the-art and future transmission technologies, including systems for electric and hybrid electric vehicles.

  10. Ultracapacitors for automotive applications

    Energy Technology Data Exchange (ETDEWEB)

    Ashtiani, Cyrus [DaimlerChrysler Corp., CIMS 526-00-00, 1870 Technology Dr., Troy, MI 48083 (United States); Wright, Randy; Hunt, Gary [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 834415-3830 (United States)

    2006-03-21

    In response to a growing consensus in the auto industry that ultracapacitors can potentially play a key role in the modern vehicle power distribution network, a task force was created at the United States Advanced Battery Consortium (USABC) to tackle issues facing the fledging industry. The task force embarked on first developing and establishing standards for performance and abuse tolerance of ultracapacitors in collaboration with the U.S. Department of Energy and National Labs. Subsequently, potential applications in the automotive industry were identified and a consensus requirement specification was drawn as a development guide for the industry. (author)

  11. Reliability in automotive ethernet networks

    DEFF Research Database (Denmark)

    Soares, Fabio L.; Campelo, Divanilson R.; Yan, Ying

    2015-01-01

    This paper provides an overview of in-vehicle communication networks and addresses the challenges of providing reliability in automotive Ethernet in particular.......This paper provides an overview of in-vehicle communication networks and addresses the challenges of providing reliability in automotive Ethernet in particular....

  12. Requirements for future automotive batteries - a snapshot

    Science.gov (United States)

    Karden, Eckhard; Shinn, Paul; Bostock, Paul; Cunningham, James; Schoultz, Evan; Kok, Daniel

    Introduction of new fuel economy, performance, safety, and comfort features in future automobiles will bring up many new, power-hungry electrical systems. As a consequence, demands on automotive batteries will grow substantially, e.g. regarding reliability, energy throughput (shallow-cycle life), charge acceptance, and high-rate partial state-of-charge (HRPSOC) operation. As higher voltage levels are mostly not an economically feasible alternative for the short term, the existing 14 V electrical system will have to fulfil these new demands, utilizing advanced 12 V energy storage devices. The well-established lead-acid battery technology is expected to keep playing a key role in this application. Compared to traditional starting-lighting-ignition (SLI) batteries, significant technological progress has been achieved or can be expected, which improve both performance and service life. System integration of the storage device into the vehicle will become increasingly important. Battery monitoring systems (BMS) are expected to become a commodity, penetrating the automotive volume market from both highly equipped premium cars and dedicated fuel-economy vehicles (e.g. stop/start). Battery monitoring systems will allow for more aggressive battery operating strategies, at the same time improving the reliability of the power supply system. Where a single lead-acid battery cannot fulfil the increasing demands, dual-storage systems may form a cost-efficient extension. They consist either of two lead-acid batteries or of a lead-acid battery plus another storage device.

  13. Performance evaluation of an automotive thermoelectric generator

    Science.gov (United States)

    Dubitsky, Andrei O.

    Around 40% of the total fuel energy in typical internal combustion engines (ICEs) is rejected to the environment in the form of exhaust gas waste heat. Efficient recovery of this waste heat in automobiles can promise a fuel economy improvement of 5%. The thermal energy can be harvested through thermoelectric generators (TEGs) utilizing the Seebeck effect. In the present work, a versatile test bench has been designed and built in order to simulate conditions found on test vehicles. This allows experimental performance evaluation and model validation of automotive thermoelectric generators. An electrically heated exhaust gas circuit and a circulator based coolant loop enable integrated system testing of hot and cold side heat exchangers, thermoelectric modules (TEMs), and thermal interface materials at various scales. A transient thermal model of the coolant loop was created in order to design a system which can maintain constant coolant temperature under variable heat input. Additionally, as electrical heaters cannot match the transient response of an ICE, modelling was completed in order to design a relaxed exhaust flow and temperature history utilizing the system thermal lag. This profile reduced required heating power and gas flow rates by over 50%. The test bench was used to evaluate a DOE/GM initial prototype automotive TEG and validate analytical performance models. The maximum electrical power generation was found to be 54 W with a thermal conversion efficiency of 1.8%. It has been found that thermal interface management is critical for achieving maximum system performance, with novel designs being considered for further improvement.

  14. Rheo-processing of semi-solid metal alloys: a new technology for manufacturing automotive and aerospace components

    CSIR Research Space (South Africa)

    Ivanchev, L

    2008-01-01

    Full Text Available The latest trend in the automotive industry to produce fuel-efficient vehicles has resulted in the increased use of aluminium and magnesium alloys. Liquid metal high pressure die-casting (HPDC) currently satisfies the bulk of the automotive industry...

  15. Downsizing assessment of automotive Stirling engines

    Science.gov (United States)

    Knoll, R. H.; Tew, R. C., Jr.; Klann, J. L.

    1983-01-01

    A 67 kW (90 hp) Stirling engine design, sized for use in a 1984 1440 kg (3170 lb) automobile was the focal point for developing automotive Stirling engine technology. Since recent trends are towards lighter vehicles, an assessment was made of the applicability of the Stirling technology being developed for smaller, lower power engines. Using both the Philips scaling laws and a Lewis Research Center (Lewis) Stirling engine performance code, dimensional and performance characteristics were determined for a 26 kW (35 hp) and a 37 kW (50 hp) engine for use in a nominal 907 kg (2000 lb) vehicle. Key engine elements were sized and stressed and mechanical layouts were made to ensure mechanical fit and integrity of the engines. Fuel economy estimates indicated that the Stirling engine would maintain a 30 to 45 percent fuel economy advantage comparable spark ignition and diesel powered vehicles in the 1984 period.

  16. Environment, automotive fuels and petroleum industry

    International Nuclear Information System (INIS)

    Tabarelli, Davide

    1997-01-01

    After several years of delays, the italian environmental regulation concerning the oil industry has taken a leading role in Europe, especially starting from 1995, for benzene limits in gasoline. This article tries to estimate what are the anticipates costs for the italian industry due to a stricter legislation on gasoline compared to the rest of Europe

  17. Automotive emission standards. (Latest citations from Pollution Abstracts). Published Search

    International Nuclear Information System (INIS)

    1993-07-01

    The bibliography contains citations concerning emission standards and air quality standards applied to automobile emissions. Included are federal and state regulations and policies regarding these emission standards. Techniques to meet emission standards are also addressed, involving fuel injection, catalysts, alternate engines, and automotive fuel refinery operations. Studies concerning implementation of automobile emission standards explore economic and environmental effects, testing and inspection procedures, and the automobile industry point of view. Most of the citations refer to gasoline engines, but a few pertain to diesel and other fuels. (Contains 250 citations and includes a subject term index and title list.)

  18. Automotive Marketing Methods and Practice

    Science.gov (United States)

    1979-09-01

    The report is a comprehensive examination of the current marketing practices, marketing methodologies, and decision-making processes utilized by the domestic automotive industry. The various marketing elements, such as products, consumer behavior, sa...

  19. Automotive LED lamp lighted appearance

    Science.gov (United States)

    Conn, Lawrence G.; Bennett, Larry R.

    2001-05-01

    The automotive optical engineer has an entirely new set of rules to follow for a 'smooth lighted appearance' with the introduction of LEDs into the automotive signal lighting market. To move away from the 'polka-dot' appearance long associated with the usage of LEDs as the light source for automotive lighting, and give the consumer a smooth lighted appearance to his lamp, there are several optical parameters that must be observed. The number and type of LEDs used, the size of the optical elements used, the spacing of the optical elements, plus many other factors all play a critical role and must be considered in the solution to the 'smooth lighted appearance' in an automotive signal lamp. The 'smooth lighted appearance' in an automotive signal lamp has long been a difficult problem to which there is more than one solution. The most visually pleasing and effective solution is not always the most easily obtainable solution since photometry requirements and smooth lighted appearance can be diametric goals. Subsequently the most cost effective and the easily 'doable' solution may not give the ultimate in aesthetically pleasing results for the consumer. Therefore, it is the purpose and intent of this paper to outline the parameters that need to be considered to obtain a 'smooth lighted appearance' for an automotive signal lamp, and to clarify the methods and 'tools' that are required to meet this goal.

  20. Automotive mechatronics operational and practical issues

    CERN Document Server

    Fijalkowski, B T

    2011-01-01

    This book presents operational and practical issues of automotive mechatronics with special emphasis on the heterogeneous automotive vehicle systems approach, and is intended as a graduate text as well as a reference for scientists and engineers involved in the design of automotive mechatronic control systems. As the complexity of automotive vehicles increases, so does the dearth of high competence, multi-disciplined automotive scientists and engineers. This book provides a discussion into the type of mechatronic control systems found in modern vehicles and the skills required by automotive scientists and engineers working in this environment. Divided into two volumes and five parts, Automotive Mechatronics aims at improving automotive mechatronics education and emphasises the training of students' experimental hands-on abilities, stimulating and promoting experience among high education institutes and produce more automotive mechatronics and automation engineers. The main subject that are treated are: VOLUME...

  1. Fuel cell electronics packaging

    National Research Council Canada - National Science Library

    Kuang, Ken; Easler, Keith

    2007-01-01

    ... more energy independent. Despite the fact that the primary focus of the new initiative revolved around automotive technologies, the President's Hydrogen Fuel Initiative was crafted into a balanced program that benefited a wide range of technologies and applications, including micro, portable, stationary fuel cells. This massive effort was given an addition...

  2. Design of lightweight multi-material automotive bodies using new material performance indices of thin-walled beams for the material selection with crashworthiness consideration

    International Nuclear Information System (INIS)

    Cui, Xintao; Zhang, Hongwei; Wang, Shuxin; Zhang, Lianhong; Ko, Jeonghan

    2011-01-01

    Currently, automotive bodies are constructed usually using a single material, e.g. steel or aluminum. Compared to single-material automotive bodies, multi-material automotive bodies allow optimal material selection in each structural component for higher product performance and lower cost. This paper presents novel material performance indices and procedures developed to guide systematic material selection for multi-material automotive bodies. These new indices enable to characterize the crashworthiness performance of complex-shaped thin-walled beams in multi-material automotive bodies according to material types. This paper also illustrates the application of these performance indices and procedures by designing a lightweight multi-material automotive body. These procedures will help to design a lightweight and affordable body favored by the automotive industry, thus to reduce fuel consumption and greenhouse gas emissions.

  3. MEMS for automotive and aerospace applications

    CERN Document Server

    Kraft, Michael

    2013-01-01

    MEMS for automotive and aerospace applications reviews the use of Micro-Electro-Mechanical-Systems (MEMS) in developing solutions to the unique challenges presented by the automotive and aerospace industries.Part one explores MEMS for a variety of automotive applications. The role of MEMS in passenger safety and comfort, sensors for automotive vehicle stability control applications and automotive tire pressure monitoring systems are considered, along with pressure and flow sensors for engine management, and RF MEMS for automotive radar sensors. Part two then goes on to explore MEMS for

  4. Japanese automotive transportation sector's impact upon global warming

    International Nuclear Information System (INIS)

    Imaseki, Takashi

    1998-01-01

    Automobiles are still increasing in number in Japan. If this continues, CO 2 emissions in this sector may increase through the first half of the 21st century. Consequently, a study of measures for reducing these CO 2 emissions is essential. In this paper, possible automotive technologies, improvements in fuel consumption and the introduction of electric vehicles are discussed. These measures are then evaluated for the Japanese case. Furthermore, market penetration of these technologies is evaluated, using life-cycle cost analysis based on initial cost and annual fuel cost. It is concluded that reducing CO 2 emissions to 1995 levels by 2010 is possible. This would require the simultaneous implementation of fuel-consumption improvements and the introduction of electric vehicles. However, automotive consumers would be reluctant to accept these technologies, particularly electric vehicles, because of their high purchase-price and low benefits in terms of operating economy. Acceptance will require financial and institutional support from the public sector in introducing these automotive technologies into the Japanese transportation sector. (author)

  5. Reducing greenhouse gas emissions from the Ontario automotive sector

    International Nuclear Information System (INIS)

    Anon.

    1995-11-01

    A variety of options to reduce greenhouse gas emissions from the automotive sector in Ontario over the next decade were discussed. Each option was assessed in terms of practicality and implications for implementation. I was concluded that improvements in fuel economy anticipated from advancing technology, with or without new mandated standards, will not be enough to offset the impact of growth in vehicle fleet size and kilometres driven. If the goal is to stabilize greenhouse gas emissions, other measures such as reducing the fleet size and vehicle kilometres travelled and accelerated vehicle retirement (scrappage) programs must be considered. Key constraints on expansion of the alternative fuel fleet were identified. These include: (1) limited availability of an adequate range of alternative fuel vehicles at competitive prices, (2) limited refuelling facility infrastructure in the case of natural gas, limited range and fuel storage capacity for natural gas; (3)current limited fuel ethanol production capacity, and (4) market perceptions of performance, reliability and safety. tabs

  6. Automotive dual-mode hydrogen generation system

    Science.gov (United States)

    Kelly, D. A.

    The automotive dual mode hydrogen generation system is advocated as a supplementary hydrogen fuel means along with the current metallic hydride hydrogen storage method for vehicles. This system consists of utilizing conventional electrolysis cells with the low voltage dc electrical power supplied by two electrical generating sources within the vehicle. Since the automobile engine exhaust manifold(s) are presently an untapped useful source of thermal energy, they can be employed as the heat source for a simple heat engine/generator arrangement. The second, and minor electrical generating means consists of multiple, miniature air disk generators which are mounted directly under the vehicle's hood and at other convenient locations within the engine compartment. The air disk generators are revolved at a speed which is proportionate to the vehicles forward speed and do not impose a drag on the vehicles motion.

  7. Escalation Practices in Automotive Development

    Directory of Open Access Journals (Sweden)

    Tomaž Jurejevčič

    2016-12-01

    Full Text Available Research Question (RQ: In automotive business many risk-involved situations occur and when detected, an escalation process takes place. Although defined and controlled by process guidelines and being supported by experts, escalation brings increased emotional pressure and stress for parties involved. Do escalation processes in automotive industry maintain all implied challenges? Purpose: The purpose of the article is to present current status of escalation processes and gaps between theory and practice cases. Results of the analysis are recommendations of good engineering practice derived also from actual experiences and learned lessons. Method: The method involves analysis of practical cases from automotive development process, lessons learned, anonymous survey of automotive engineers and classification of experiences. Results: Results of the survey have shown that the controlled escalation process for know-how related escalations is needed in order to establish the environment where the team is able to provide new, sometimes unconventional ideas for the problem to be solved. Organization: Presented recommendations and measures enable organization and managers to put the expertise and experiences of employees into action for problem solving during escalation. Originality: In this article some practices are presented that, although simple and some yet seen, with proper adjustment stemming from real life processes give a fruitful settlement of escalations in automotive development business.

  8. Automotive Sensors and MEMS Technology

    Science.gov (United States)

    Nonomura, Yutaka

    - Automotive sensors are used for emission gas purification, energy conservation, car kinematic performance, safety and ITS (intelligent transportation system). The comparison of the sensor characteristics was made for their application area. Many kinds of the principles are applied for the sensors. There are two types of sensors, such as physical and chemical one. Many of the automotive sensors are physical type such as mechanical sensors. And a gas sensor is a chemical type. The sensors have been remarkably developed with the advancement of the MEMS (Micro Electro Mechanical Systems) technology. In this paper, gas, pressure, combustion pressure, acceleration, magnetic, and angular rate sensors for automotive use are explained with their features. The sensors are key devices to control cars in the engine, power train, chassis and safety systems. The environment resistance, long term reliability, and low cost are required for the automotive sensors. They are very hard to be resolved. However, the sensor technology contributes greatly to improving global environment, energy conservation, and safety. The applications of automotive sensors will be expanded with the automobile developments.

  9. The Progressive Insurance Automotive X PRIZE Education Program

    Energy Technology Data Exchange (ETDEWEB)

    Robyn Ready

    2011-12-31

    The Progressive Insurance Automotive X PRIZE Education Program conducted education and outreach activities and used the competition's technical goals and vehicle demonstrations as a means of attracting students and the public to learn more about advanced vehicle technologies, energy efficiency, climate change, alternative fuels, and the science and math behind efficient vehicle development. The Progressive Insurance Automotive X PRIZE Education Program comprised three integrated components that were designed to educate the general public and create a multi-tiered initiative to engage students and showcase the 21st century skills students will need to compete in our global economy: teamwork, creativity, strong literacy, math and science skills, and innovative thinking. The elements included an Online Experience, a National Student Contest, and in person education events and activites. The project leveraged online connections, strategic partnerships, in-classroom, and beyond-the-classroom initiatives, as well as mainstream media. This education program supported by the U.S. Department of Energy (DOE) also funded the specification of vehicle telemetry and the full development and operation of an interactive online experience that allowed internet users to follow the Progressive Insurance Automotive X PRIZE vehicles as they performed in real-time during the Progressive Insurance Automotive X PRIZE competition events.

  10. Environmental sustainability: plastic's evolving role in the automotive life cycle

    International Nuclear Information System (INIS)

    Jekel, L.; Tam, E.K.L.

    2002-01-01

    One method of assessing the sustainability of manufactured products involves performing a life cycle analysis for a product and comparing it to alternative ones, or else examining if individual stages of the product can be modified. LCA applications are being used more extensively, especially in the automotive and related industries. Automotive plastics in particular are being scrutinized with much greater care. Plastic components have replaced metal ones in vehicle manufacturing to improve vehicle fuel efficiency and aesthetics. However, at the end of a vehicle's life, recycling rates for plastic are negligible when compared to those of steel. In order to gain the full environmental benefits of using plastic as a vehicle material, plastics must be recycled at the end of a vehicle's life, especially given their increasing use. While a variety of processes have been developed for the recycling of automotive plastics, the challenges of sorting, processing, and finally recycling a heterogeneous mixture of used plastics have yet to be effectively solved. A preliminary life cycle assessment of a plastic automotive fascia demonstrates the usefulness of this eco-balance technique in evaluating potential improvements to manufacturing and end-of-life processes. Improving the manufacturing process may reduce environmental burdens to a larger extent than just recycling the plastic. (author)

  11. MICROALLOYED STEELS FOR THE AUTOMOTIVE INDUSTRY

    Directory of Open Access Journals (Sweden)

    Debanshu Bhattacharya

    2014-12-01

    Full Text Available Two major drivers for the use of newer steels in the automotive industry are fuel efficiency and increased safety performance. Fuel efficiency is mainly a function of weight of steel parts, which in turn, is controlled by gauge and design. Safety is determined by the energy absorbing capacity of the steel used to make the part. All of these factors are incentives for the U.S. automakers to use both Highly Formable and Advanced High Strength Steels (AHSS to replace the conventional steels used to manufacture automotive parts in the past. AHSS is a general term used to describe various families of steels. The most common AHSS is the dual-phase steel that consists of a ferrite-martensite microstructure. These steels are characterized by high strength, good ductility, low tensile to yield strength ratio and high bake hardenability. Another class of AHSS is the complex-phase or multi-phase steel which has a complex microstructure consisting of various phase constituents and a high yield to tensile strength ratio. Transformation Induced Plasticity (TRIP steels is another class of AHSS steels finding interest among the U.S. automakers. These steels consist of a ferrite-bainite microstructure with significant amount of retained austenite phase and show the highest combination of strength and elongation, so far, among the AHSS in use. High level of energy absorbing capacity combined with a sustained level of high n value up to the limit of uniform elongation as well as high bake hardenability make these steels particularly attractive for safety critical parts and parts needing complex forming. A relatively new class of AHSS is the Quenching and Partitioning (Q&P steels. These steels seem to offer higher ductility than the dual-phase steels of similar strengths or similar ductility as the TRIP steels at higher strengths. Finally, martensitic steels with very high strengths are also in use for certain parts. The most recent initiative in the area of AHSS

  12. Automotive Mechanics. Student Learning Guides.

    Science.gov (United States)

    Ridge Vocational-Technical Center, Winter Haven, FL.

    These 33 learning guides are self-instructional packets for 33 tasks identified as essential for performance on an entry-level job in automotive mechanics. Each guide is based on a terminal performance objective (task) and 1-9 enabling objectives. For each enabliing objective, some or all of these materials may be presented: learning steps…

  13. Automotive the Future of Mobility

    NARCIS (Netherlands)

    ir. Frank Rieck; ir. Cees Machielse; Ron van Duin

    2017-01-01

    Will the Automotive era come to an end in the 21th century? Looking at today’s environmental and economic challenges of the use of last century technology cars and listening to some trend watchers one could think so. Cars can be regarded, as an old school status product indeed, for which there is

  14. On Ugliness and the Automotive

    DEFF Research Database (Denmark)

    Herriott, Richard

    2016-01-01

    The function of this essay is to to see what consequences a consideration of ugliness in automotive styling has for the theories of three writers on aesthetics in design: David Pye, Roger Scruton and Ralf Weber. As such, the concepts of beauty and ugliness will be treated in brief before moving...

  15. Future perspectives on automotive CAE

    NARCIS (Netherlands)

    Bensler, Henry; Eller, Tom; Kabat vel Job, Alexander; Magoulas, Nikolaos; Yigit, Emrah; Van Tongeren, A.

    2014-01-01

    Computer Aided Engineering (CAE) is an integral part of today’s automotive design process. Very often OEM’s rely solely on software vendors to provide appropriate solutions. On the other hand, some companies still use in-house developed software for specific applications. It is, however, a

  16. Automotive, the Future of Mobility

    NARCIS (Netherlands)

    Rieck, Frank; Machielsen, C.; van Duin, Ron

    2017-01-01

    Will the Automotive era come to an end in the 21th century? Looking at today’s environmental and economic challenges of the use of cars based on last century technology and listening to some trend watchers one could think so. Cars can be regarded, as an old school status product indeed, for which

  17. Innovative Technology in Automotive Technology

    Science.gov (United States)

    Gardner, John

    2007-01-01

    Automotive Technology combines hands-on training along with a fully integrated, interactive, computerized multistationed facility. Our program is a competency based, true open-entry/open-exit program that utilizes flexible self-paced course outlines. It is designed around an industry partnership that promotes community and economic development,…

  18. Current and Future Uses of Aluminum in the Automotive Industry

    Science.gov (United States)

    Long, R. S.; Boettcher, E.; Crawford, D.

    2017-12-01

    Aluminum use is growing in automotive closures and body in white applications to improve vehicle performance and fuel economy. The auto industry is looking for higher-strength aluminum materials needed for strength-driven safety-critical parts. Through cooperation with industrial partners and support from the Department of Energy (DOE), multiple experimental 7xxx alloys were developed for automotive applications. The objective is to enable complex shapes to be formed at temperatures below 225°C. A demonstration part has been developed that is representative of the forming challenges within a current hot-stamped door ring component. This part tooling has been built and installed into a press line which includes blank heating and robotic transfer. Forming trials of these alloys are currently underway and the formability, strength and corrosion performance of these materials are being evaluated.

  19. Antenna Arrays and Automotive Applications

    CERN Document Server

    Rabinovich, Victor

    2013-01-01

    This book throws a lifeline to designers wading through mounds of antenna array patents looking for the most suitable systems for their projects. Drastically reducing the research time required to locate solutions to the latest challenges in automotive communications, it sorts and systematizes material on cutting-edge antenna arrays that feature multi-element communication systems with enormous potential for the automotive industry. These new systems promise to make driving safer and more efficient, opening up myriad applications, including vehicle-to-vehicle traffic that prevents collisions, automatic toll collection, vehicle location and fine-tuning for cruise control systems. This book’s exhaustive coverage begins with currently deployed systems, frequency ranges and key parameters. It proceeds to examine system geometry, analog and digital beam steering technology (including "smart" beams formed in noisy environments), maximizing signal-to-noise ratios, miniaturization, and base station technology that ...

  20. Advanced Materials for Automotive Application

    International Nuclear Information System (INIS)

    Tisza, M

    2013-01-01

    In this paper some recent material developments will be overviewed mainly from the point of view of automotive industry. In car industry, metal forming is one of the most important manufacturing processes imposing severe restrictions on materials; these are often contradictory requirements, e.g. high strength simultaneously with good formability, etc. Due to these challenges and the ever increasing demand new material classes have been developed; however, the more and more wide application of high strength materials meeting the requirements stated by the mass reduction lead to increasing difficulties concerning the formability which requires significant technological developments as well. In this paper, the recent materials developments will be overviewed from the point of view of the automotive industry

  1. GLOBAL PERSPECTIVES IN AUTOMOTIVE INDUSTRY

    Directory of Open Access Journals (Sweden)

    NICOLETA ISAC

    2010-01-01

    Full Text Available The automotive sector is characterised by a relatively low trade/salesratio. While the production of most automotive producers in the world is spread over variouscountries in the value chain, the brands are still considered to reflect some national identity.Internationalisation strategies may change over the lifecycle of the product and automakerstend to pursue diametrically opposed strategies. In mature markets, it is about managing whatgoes on beneath a static surface; in emerging markets’ dynamic environments, companies muststrategically position themselves to benefit from growth opportunities. However, without theright strategy and execution in mature markets, it is clear that traditional OEMs cannot profitfrom emerging markets-the persistence of structural issues in mature market operationseventually will rob all but the most resilient competitors of the opportunity to compete inemerging markets.

  2. Automotive Powertrain Software Evaluation Tool

    OpenAIRE

    Powale, Kalkin

    2018-01-01

    The software is a key differentiator and driver of innovation in the automotive industry. The major challenges for software development are increasing in complexity, shorter time-to-market, increase in development cost and demand of quality assurance. The complexity is increasing due to emission legislations, variants of product and new communication technologies being interfaced with the vehicle. The shorter development time is due to competition in the market, which requires faster feedback...

  3. United States Automotive Materials Partnership LLC (USAMP)

    Energy Technology Data Exchange (ETDEWEB)

    United States Automotive Materials Partnership

    2011-01-31

    The United States Automotive Materials Partnership LLC (USAMP) was formed in 1993 as a partnership between Chrysler Corporation, Ford Motor Company, and General Motors Corporation. Since then the U.S. Department of Energy (DOE) has supported its activities with funding and technical support. The mission of the USAMP is to conduct vehicle-oriented research and development in materials and materials processing to improve the competitiveness of the U.S. Auto Industry. Its specific goals are: (1) To conduct joint research to further the development of lightweight materials for improved automotive fuel economy; and (2) To work with the Federal government to explore opportunities for cooperative programs with the national laboratories, Federal agencies such as the DOE and universities. As a major component of the DOE's Office of FreedomCAR and Vehicle Technologies Program (FCVT) collaboration with the USAMP, the Automotive Lightweighting Materials (ALM) program focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. The FCVT was announced in FY 2002 and implemented in FY 2003, as a successor of the Partnership for a New Generation of Vehicles (PNGV), largely addressed under the first Cooperative Agreement. This second USAMP Cooperative Agreement with the DOE has expanded a unique and valuable framework for collaboratively directing industry and government research efforts toward the development of technologies capable of solving important societal problems related to automobile transportation. USAMP efforts are conducted by the domestic automobile manufacturers, in collaboration with materials and manufacturing suppliers, national laboratories, universities, and other technology or trade organizations. These interactions provide a direct route for implementing newly

  4. Evaluation of the environmental impact of modern passenger cars on petrol, diesel, automotive LPG and CNG

    NARCIS (Netherlands)

    Hendriksen, P.; Vermeulen, R.J.; Rijkeboer, R.C.; Bremmers, D.A.C.M.; Smokers, R.T.M.; Winkel, R.G.

    2003-01-01

    The project reported here concerns an investigation into the environmental performance of modern passenger cars on four different fuels: petrol, diesel, automotive LPG and CNG. The objectives of the project were twofold: - To make a valid and useful comparison between modern vehicles fuelled by

  5. Rare earth metals for automotive exhaust catalysts

    International Nuclear Information System (INIS)

    Shinjoh, Hirohumi

    2006-01-01

    The usage of rare earth metals for automotive exhaust catalysts is demonstrated in this paper. Rare earth metals have been widely used in automotive catalysts. In particular, three-way catalysts require the use of ceria compounds as oxygen storage materials, and lanthana as both a stabilizer of alumina and a promoter. The application for diesel catalysts is also illustrated. Effects of inclusion of rare earth metals in automotive catalysts are discussed

  6. SUPPLIER SELECTION CRITERIA OF TURKISH AUTOMOTIVE INDUSTRY

    OpenAIRE

    GÜRLER , Araş. Gör. İbrahim

    2007-01-01

    Supplier selection in supply chain management becomes more important due to the competition between supply chains rather than companies. Managing the supply chain is an important but complex issue for automotive manufacturers. This increases the importance of effective supplier selection in automotive industry. In this study, in order to investigate the supplier selection in supply chain management a questionnaire is applied to companies of Turkish Automotive Industry which is being affected ...

  7. International Congress of Automotive and Transport Engineering

    CERN Document Server

    Ispas, Nicolae

    2017-01-01

    The volume will include selected and reviewed papers from CONAT - International Congress of Automotive and Transport Engineering to be held in Brasov, Romania, in October 2016. Authors are experts from research, industry and universities coming from 14 countries worldwide. The papers are covering the latest developments in automotive vehicles and environment, advanced transport systems and road traffic, heavy and special vehicles, new materials, manufacturing technologies and logistics, accident research and analysis and innovative solutions for automotive vehicles. The conference will be organized by SIAR (Society of Automotive Engineers from Romania) in cooperation with FISITA. .

  8. NASA/DOE automotive Stirling engine project. Overview 1986

    Energy Technology Data Exchange (ETDEWEB)

    Beremand, D.G.; Shaltens, R.K.

    1986-01-01

    The DOE/NASA Automotive Stirling Engine Project is reviewed and its technical progress and status are presented. Key technologies in materials, seals, and piston rings are progressing well. Seven first-generation engines, and midifications thereto, have accumulated over 15 000 hr of test time, including 1100 hr of in-vehicle testing. Results indicate good progress toward the program goals. The first second-generation engine is now undergoing initial testing. It is expected that the program goal of a 30-percent improvement in fuel economy will be achieved in tests of a second-generation engine in a Celebrity vehicle.

  9. The automobile of the future: engine technologies and automotive fuels developed by IFP; l'automobile du futur: les technologies moteurs et carburants developpes par l'IFP

    Energy Technology Data Exchange (ETDEWEB)

    Appert, O.; Pinchon, Ph.

    2004-07-01

    In front of the challenges of climate change and depletion of petroleum reserves, in front of the continuous strengthening of pollution regulations applied to automobile (Euro IV and V) and the advances of R and D, several ways of research can be explored to answer the mobility needs of the coming decades. The IFP takes stock of these topics in this press kit which comprises 11 documents: the synthesis of O. Appert and P. Pinchon's talk about 'the cleaner and multi-energies automobile of the future', the slides of this presentation, the future evolutions of automobiles motorizations, the long-term evolutions of engines/fuels (brief for the Panorama 2004 colloquium), diesel fuel in the USA (brief for the Panorama 2004 colloquium), bio-fuels in Europe (brief for the Panorama 2004 colloquium), diesel pollution abatement: efficient results from the IFP's diesel combustion process 'NADI'(TM), the presentation of the IFP scientific meeting of September 22-23, 2004 'which fuels for low CO{sub 2} engines?', the strategic positioning of IFP in the world energy and environmental context, the brochures 'IFP engines and fuels: a competitive advantage' and 'innovating for a sustainable development in the domain of energy'. (J.S.)

  10. 1975 Automotive Characteristics Data Base

    Science.gov (United States)

    1976-10-01

    A study of automobile characteristics as a supportive tool for auto energy consumption, fuel economy monitoring, and fleet analysis studies is presented. This report emphasizes the utility of efficient data retrieval methods in fuel economy analysis,...

  11. Advanced high strength steels for automotive industry

    Directory of Open Access Journals (Sweden)

    Galán, J.

    2012-04-01

    Full Text Available The car industry is facing pressure because of the growing demand for more fuel-efficient passenger cars. In order to limit energy consumption and air pollution the weight of the carbody has to be reduced. At the same time, high levels of safety have to be guaranteed. In this situation, the choice of material becomes a key decision in car design. As a response to the requirements of the automotive sector, high strength steels and advanced high strength steels have been developed by the steel industry. These modern steel grades offer an excellent balance of low cost, light weight and mechanical properties.

    La industria del automóvil se enfrenta a una creciente demanda de vehículos de pasajeros más eficientes. Con el fin de disminuir el consumo de energía y la contaminación ambiental, el peso del vehículo tiene que ser reducido, al mismo tiempo que se garantizan altos niveles de seguridad. Ante esta situación, la elección de material se convierte en una decisión crucial en el diseño del vehículo. Como respuesta a las necesidades del sector automovilístico, nuevos aceros avanzados y de alta resistencia, han sido desarrollados por la industria siderúrgica. Dichos tipos de acero ofrecen un excelente equilibrio de precio, peso y propiedades mecánicas.

  12. Future automotive materials: Evolution or revolution

    Science.gov (United States)

    Beardmore, P.

    1990-01-01

    An exciting era is evolving in the application of new materials technologies to automotive applications. The desire on the part of the automobile industry to completely satisfy the customers while concurrently meeting increasing demands and regulations for stringent emission control and fuel efficiency is opening a plethora of opportunities for new materials. In many cases, materials solutions are the only mechanisms for resolving some of the upcoming issues. The materials scientist and engineer will therefore have a primary role to play and will assume a position of significance hithertofore unseen in the automobile industry. The nature of the industry dictates that changes are primarily evolutionary with respect to chronology but nevertheless some of the future material changes will be revolutionary in nature. This presentation will treat three primary systems of the vehicle separately, based on the different materials approaches which will be adopted. These areas are: (1) skin panels, (2) structures, and (3) powertrains. The competition between a variety of new materials in these 3 systems will be discussed in detail with the various tradeoffs being outlined. Amongst the more prominent of the new breed of materials will be new steel technologies, structural plastics (FRP), aluminum alloys (conventional and rapidly solidified), titanium alloys, metal matrix composites and smart materials (electrorheological fluids, etc.). The pace of development and application is accelerating rapidly and the impetus is likely to increase.

  13. ORNL-GM: Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Jun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhou, Yan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Luo, Huimin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Toops, Todd J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brookshear, Daniel W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stump, Benjamin C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Viola, Michael B. [General Motors (GM) Technical Center, Pontiac, MI (United States); Zreik, Khaled [General Motors (GM) Technical Center, Pontiac, MI (United States); Ahmed, Tasfia [General Motors (GM) Technical Center, Pontiac, MI (United States)

    2017-01-01

    The overall objective of this project are as follows: Further develop ionic liquid (IL)-additized lowviscosity engine oils meeting the GF-5/6 specifications and possessing superior lubricating characteristics; Expand the IL additive technology to rear axle lubricants; and Seek a combined improvement in the vehicle fuel economy

  14. Using Technology to Enhance an Automotive Program

    Science.gov (United States)

    Ashton, Denis

    2009-01-01

    Denis Ashton uses technology in his automotive technology program at East Valley Institute of Technology (EVIT) to positively impact student outcomes. Ashton, the department chair for the automotive programs at EVIT, in Mesa, Arizona, says that using an interactive PowerPoint curriculum makes learning fun for students and provides immediate…

  15. Dynamic and Acoustic Characterisation of Automotive Wheels

    Directory of Open Access Journals (Sweden)

    Francesca Curà

    2004-01-01

    Full Text Available The subject of this paper is the dynamic and acoustic characterisation of an automotive wheel. In particular, an experimental research activity previously performed by the authors about the dynamic behaviour of automotive wheels has been extended to the acoustic field.

  16. Veranderende automotive wereld vraagt om verandering onderwijs

    NARCIS (Netherlands)

    H.J.C. Nas

    2011-01-01

    Met dit document wil ik de lezer een nieuwe invalshoek tonen op mobiliteit (Driving Guidance) en een andere benadering van automotive hbo onderwijs. De wereld om ons heen verandert en deze nieuwe wereld zal een ander type automotive ingenieur eisen. Dit is een korte weergave van een lezing voor de

  17. Carbon composite manufacturing in automotive volume production

    DEFF Research Database (Denmark)

    Geiger, Raphael; Pahl, Julia

    2017-01-01

    Lightweight constructions are a continuously increasing trend in the automotive industry. Main drivers for that trend are the challenging emission reduction targets regarding combustion engines and increasing ranges in electric mobility. This article presents different composite production methods...... and discusses their ability within mass production giving also an example within the automotive production....

  18. Energy. Which fuels for tomorrow? Status of bio-fuels

    International Nuclear Information System (INIS)

    Fleaux-Mulot, R.; Ratel, H.

    2005-01-01

    France wants to include up to 5.75% of bio-fuels in its automotive fuels by 2008. This article presents the advantages and drawbacks of this policy: reduction of the fossil fuels dependence, positive impact on the greenhouse effect but possible environmental impacts linked with intensive cultivation techniques, no problem of compatibility with the vehicles engine but the production costs remain three times higher than for petroleum. (J.S.)

  19. Integrated fuel processor development

    International Nuclear Information System (INIS)

    Ahmed, S.; Pereira, C.; Lee, S. H. D.; Krumpelt, M.

    2001-01-01

    The Department of Energy's Office of Advanced Automotive Technologies has been supporting the development of fuel-flexible fuel processors at Argonne National Laboratory. These fuel processors will enable fuel cell vehicles to operate on fuels available through the existing infrastructure. The constraints of on-board space and weight require that these fuel processors be designed to be compact and lightweight, while meeting the performance targets for efficiency and gas quality needed for the fuel cell. This paper discusses the performance of a prototype fuel processor that has been designed and fabricated to operate with liquid fuels, such as gasoline, ethanol, methanol, etc. Rated for a capacity of 10 kWe (one-fifth of that needed for a car), the prototype fuel processor integrates the unit operations (vaporization, heat exchange, etc.) and processes (reforming, water-gas shift, preferential oxidation reactions, etc.) necessary to produce the hydrogen-rich gas (reformate) that will fuel the polymer electrolyte fuel cell stacks. The fuel processor work is being complemented by analytical and fundamental research. With the ultimate objective of meeting on-board fuel processor goals, these studies include: modeling fuel cell systems to identify design and operating features; evaluating alternative fuel processing options; and developing appropriate catalysts and materials. Issues and outstanding challenges that need to be overcome in order to develop practical, on-board devices are discussed

  20. Hydrogen system (hydrogen fuels feasibility)

    International Nuclear Information System (INIS)

    Guarna, S.

    1991-07-01

    This feasibility study on the production and use of hydrogen fuels for industry and domestic purposes includes the following aspects: physical and chemical properties of hydrogen; production methods steam reforming of natural gas, hydrolysis of water; liquid and gaseous hydrogen transportation and storage (hydrogen-hydride technology); environmental impacts, safety and economics of hydrogen fuel cells for power generation and hydrogen automotive fuels; relevant international research programs

  1. Analysis of the potential for new automotive uses of wrought magnesium

    Energy Technology Data Exchange (ETDEWEB)

    Gaines, L.; Cuenca, R.; Wu, S. [Argonne National Lab., IL (United States); Stodolsky, F. [Argonne National Lab., IL (United States)]|[Argonne National Lab., Washington, DC (United States)

    1996-02-01

    The Center for Transportation Research at Argonne National Laboratory has performed a study for the Lightweight Materials Program within the US Department of Energy`s Office of Transportation Materials to evaluate the suitability of wrought magnesium and its alloys to replace steel or aluminum for automotive structural and sheet applications. Vehicle weight reduction is one of the major means available for improving automotive fuel efficiency. Although high-strength steels, Al, and polymers are already being used to achieve significant weight reductions, substantial additional weight reductions could be achieved by increased use of Mg (whose density is less than one-fourth that of steel and only two-thirds that of Al). This study shows that Mg sheet could be used in automotive body nonstructural and semistructural applications, whereas extrusions could be used in such structural applications as spaceframes. The primary barrier to such uses of wrought Mg is high cost.

  2. Evaluation of Cetane Improver Additive in Alternative Jet Fuel Blends

    Science.gov (United States)

    2016-07-01

    Tank Automotive Research, Development and Engineering Center Warren, Michigan 48397-5000 Evaluation of Cetane Improver Additive in Alternative Jet...Registration No. -Technical Report- U.S. Army Tank Automotive Research, Development, and Engineering Center Detroit Arsenal Warren, Michigan 48397...5000 Distribution Statement A: Approved for public release: distribution unlimited. Evaluation of Cetane Improver Additive in Alternative Jet Fuel

  3. Supply chain management problems at South African automotive ...

    African Journals Online (AJOL)

    The problems that automotive component manufacturers (ACMs) experience in automotive supply chains is an important contemporary issue. The role of ACMs in the competitiveness and survival of the automotive industry has never been as pronounced. Original equipment manufacturers (OEMs, also known as automotive

  4. Petroleum Diesel Fuel and Linseed Oil Mixtures as Engine Fuels

    Science.gov (United States)

    Markov, V. A.; Kamaltdinov, V. G.; Savastenko, A. A.

    2018-01-01

    The actual problem is the use of alternative biofuels in automotive diesel engines. Insufficiently studied are the indicators of toxicity of exhaust gases of these engines operating on biofuel. The aim of the study is to identify indicators of the toxicity of exhaust gases when using of petroleum diesel fuel and linseed oil mixtures as a fuel for automotive diesel engines. Physical and chemical properties of linseed oil and its mixtures with petroleum diesel fuel are considered. Experimental researches of D-245.12C diesel are carried out on mixtures of diesel fuel and corn oil with a different composition. An opportunity of exhaust toxicity indexes improvement using these mixtures as a fuel for automobiles engine is shown.

  5. Prospects for MEMS in the Automotive Industry

    Directory of Open Access Journals (Sweden)

    Richard DIXON

    2007-12-01

    Full Text Available An automotive sector as a growth market for MEMS sensors is analyzed in the article. The automotive sector accounted for $1.6 billion, making this the second biggest opportunity after IT peripherals and inkjet print heads. By 2011 the market will top $2.2 billion, a CAGR of around 7%. The main applications in revenues terms are, in order, pressure sensors, gyroscopes, accelerometers and flow sensors and this will remain so for the foreseeable future. Automotive companies are forced to innovate as a result of competition and price pressures.

  6. Novel thermocouples for automotive applications

    Directory of Open Access Journals (Sweden)

    P. Gierth

    2018-02-01

    Full Text Available Measurement of temperatures in engine and exhaust systems in automotive applications is necessary for thermal protection of the parts and optimizing of the combustion process. State-of-the-art temperature sensors are very limited in their response characteristic and installation space requirement. Miniaturized sensor concepts with a customizable geometry are needed. The basic idea of this novel sensor concept is to use thick-film technology on component surfaces. Different standardized and especially nonstandard material combinations of thermocouples have been produced for the validation of this technology concept. Application-oriented measurements took place in the exhaust system of a test vehicle and were compared to standard laboratory conditions.

  7. Parametric studies on automotive radiators

    International Nuclear Information System (INIS)

    Oliet, C.; Oliva, A.; Castro, J.; Perez-Segarra, C.D.

    2007-01-01

    This paper presents a set of parametric studies performed on automotive radiators by means of a detailed rating and design heat exchanger model developed by the authors. This numerical tool has been previously verified and validated using a wide experimental data bank. A first part of the analysis focuses on the influence of working conditions on both fluids (mass flows, inlet temperatures) and the impact of the selected coolant fluid. Following these studies, the influence of some geometrical parameters is analysed (fin pitch, louver angle) as well as the importance of coolant flow lay-out on the radiator global performance. This work provides an overall behaviour report of automobile radiators working at usual range of operating conditions, while significant knowledge-based design conclusions have also been reported. The results show the utility of this numerical model as a rating and design tool for heat exchangers manufacturers, being a reasonable compromise between classic ε - NTU methods and CFD

  8. Design of the 4-215 D. A. automotive Stirling engine

    Energy Technology Data Exchange (ETDEWEB)

    van Giessel, R.; Reinink, F.

    1977-01-01

    The Stirling engine holds out prospects of achieving a low pollution, quiet automotive power plant with excellent fuel economy and multi-fuel capability. N. V. Philips, of Holland, has been working with Ford Motor Company since 1972 on a joint program to build, test, and develop a conceptual version of the engine to determine its real potential. A description is given of the approach taken in the design of a four-cylinder double-acting 170-hp Stirling engine with a swash-plate drive, suitable for passenger car installation. Performance and steady-state fuel economy measured on a dynamometer are also presented.

  9. Technology Transfer in the Global Automotive Value Chain. Lessons from the Turkish Automotive Industry

    OpenAIRE

    M. Teoman Pamukçu; Alper Sönmez

    2011-01-01

    The automotive industry is one of the main contributors to value added, employment and exports of the Turkish economy and it has undergone major changes since the mid-nineties. Most of the automotive manufacturers in Turkey are either joint ventures or wholly-owned affiliates of multinational companies. Literature on global value chains point to the possibility of technology transfer occurring through backward linkages from automotive manufacturers to their suppliers. We test for the existenc...

  10. multilevel buck converter for automotive electrical load

    African Journals Online (AJOL)

    user

    MULTILEVEL BUCK CONVERTER FOR AUTOMOTIVE ELECTRICAL LOAD. E. T. Yabefa1,* and D. Ebregbe2. 1ELECTRICAL DEPARTMENT, BAYELSA STATE COLLEGE OF ARTS & SCIENCE (BYCAS) YENAGOA, BAYELSA STATE NIGERIA. 2ELECTRICAL ENGINEERING DEPARTMENT, NIGER DELTA UNIVERSITY, ...

  11. Sustainable automotive energy system in China

    CERN Document Server

    CAERC, Tsinghua University

    2014-01-01

    This book identifies and addresses key issues of automotive energy in China. It covers demography, economics, technology and policy, providing a broad perspective to aid in the planning of sustainable road transport in China.

  12. Fatal exit the automotive black box debate

    CERN Document Server

    Kowalick, Tom

    2005-01-01

    "Fatal Exit: The Automotive Black Box Debate cuts through thirty years of political wrangling and institutional biases to provide an argument for the Motor Vehicle Event Data Recorder (MVEDR). This automotive equivalent of an airplane's flight recorder or black box is intended to solve the mysteries of car crashes and improve the safety of our roads. The reader is taken inside the automotive industry and the government highway safety establishment to foster an understanding of the politics and the positions on all sides of this safety debate. The author takes an unbiased approach, chronologically presenting each argument and uncovering the agendas and mandates of each of the stakeholders." "This publication is essential reading for all consumers who need to have their voices heard on this critical issue, as well as for attorneys, public safety advocates, public policy administrators, engineers, automotive professionals, journalists, and insurance executives."--Jacket.

  13. INFLUENCE OF AUTOMOTIVE CLUSTERS IN REGIONAL DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    Constantin BORDEI

    2014-11-01

    Full Text Available This paper proposes an overview of the evolution in the automotive sector in the process of regional development. The fundamental changes made by the component supplier sector improved the regional development and manufacturing process. Automotive industry is one of the modern sectors in many countries that benefits of a high technology impact and creates jobs that reduces unemployment across Europe. The auto industry changed cities, regions and countries into poles of development and it becomes more and more efficient. The high foreign direct investments from the automotive sector play an important role in regional development process. Continuous changes are being made in the economy, society, and company; in conclusion the automotive clusters will always be a subject of analysis.

  14. Nonlinear estimation and control of automotive drivetrains

    CERN Document Server

    Chen, Hong

    2014-01-01

    Nonlinear Estimation and Control of Automotive Drivetrains discusses the control problems involved in automotive drivetrains, particularly in hydraulic Automatic Transmission (AT), Dual Clutch Transmission (DCT) and Automated Manual Transmission (AMT). Challenging estimation and control problems, such as driveline torque estimation and gear shift control, are addressed by applying the latest nonlinear control theories, including constructive nonlinear control (Backstepping, Input-to-State Stable) and Model Predictive Control (MPC). The estimation and control performance is improved while the calibration effort is reduced significantly. The book presents many detailed examples of design processes and thus enables the readers to understand how to successfully combine purely theoretical methodologies with actual applications in vehicles. The book is intended for researchers, PhD students, control engineers and automotive engineers. Hong Chen is a professor at the State Key Laboratory of Automotive Simulation and...

  15. Fuels for fuel cells: Fuel and catalyst effects on carbon formation

    Energy Technology Data Exchange (ETDEWEB)

    Borup, R. L. (Rodney L.); Inbody, M. A. (Michael A.); Perry, W. L. (William Lee); Parkinson, W. J. (William Jerry),

    2002-01-01

    The goal of this research is to explore the effects of fuels, fuel constituents, additives and impurities on the performance of on-board hydrogen generation devices and consequently on the overall performance of fuel cell systems using reformed hydrocarbon fuels. Different fuels and components have been tested in automotive scale, adiabatic autothermal reactors to observe their relative reforming characteristics with various operating conditions. Carbon formation has been modeled and was experimentally monitored in situ during operation by laser measurements of the effluent reformate. Ammonia formation was monitored, and conditions varied to observe under what conditions N H 3 is made.

  16. Automotive perspective on laser material processing

    International Nuclear Information System (INIS)

    Roessler, D.M.

    1989-01-01

    In this paper a broad review is given of the development and use of laser processing in the automotive industry. a brief introduction to the major types of processing lasers and related systems is followed by a summary of the major processing regimes. Examples are given of the automotive industry's use of lasers in a variety of applications, from heat treating and welding, to cutting and marking

  17. SELECTION METHOD FOR AUTOMOTIVE PARTS RECONDITIONING

    Directory of Open Access Journals (Sweden)

    Dan Florin NITOI

    2015-05-01

    Full Text Available Paper presents technological methods for metal deposition, costs calculation and clasification for the main process that helps in automotive technologies to repair or to increase pieces properties. Paper was constructed based on many technological experiments that starts from practicans and returns to them. The main aim is to help young engineers or practicians engineers to choose the proper reconditioning process with the best information in repairing pieces from automotive industry.

  18. Guidelines for use of Hydrogen Fuel in Commercial Vehicles

    Science.gov (United States)

    2008-01-01

    Over the next 50 years, hydrogen use is expected to grow dramatically as an automotive and electrical power source fuel. As hydrogen becomes commercially viable, the safety concerns associated with hydrogen systems, equipment, and operation are of co...

  19. Laser metrology — a diagnostic tool in automotive development processes

    Science.gov (United States)

    Beeck, Manfred-Andreas; Hentschel, Werner

    2000-08-01

    Laser measurement techniques are widely used in automotive development processes. Applications at Volkswagen are presented where laser metrology works as a diagnostic tool for analysing and optimising complex coupled processes inside and between automotive components and structures such as the reduction of a vehicle's interior or outer acoustic noise, including brake noise, and the combustion analysis for diesel and gasoline engines to further reduce fuel consumption and pollution. Pulsed electronic speckle pattern interferometry (ESPI) and holographic interferometry are used for analysing the knocking behaviour of modern engines and for correct positioning of knocking sensors. Holographic interferometry shows up the vibrational behaviour of brake components and their interaction during braking, and allows optimisation for noise-free brake systems. Scanning laser vibrometry analyses structure-born noise of a whole car body for the optimisation of its interior acoustical behaviour.Modern engine combustion concepts such as in direct-injection (DI) gasoline and diesel engines benefit from laser diagnostic tools which permit deeper insight into the in-cylinder processes such as flow generation, fuel injection and spray formation, atomisation and mixing, ignition and combustion, and formation and reduction of pollutants. The necessary optical access inside a cylinder is realised by so-called 'transparent engines' allowing measurements nearly during the whole engine cycle. Measurement techniques and results on double-pulse particle image velocimetry (PIV) with a frequency-doubled YAG laser for in-cylinder flow analysis are presented, as well as Mie-scattering on droplets using a copper vapour laser combined with high-speed filming, and laser-induced fluorescence (LIF) with an excimer laser for spray and fuel vapour analysis.

  20. Toward sustainable fuel cells

    DEFF Research Database (Denmark)

    Stephens, Ifan; Rossmeisl, Jan; Chorkendorff, Ib

    2016-01-01

    A quarter of humanity's current energy consumption is used for transportation (1). Low-temperature hydrogen fuel cells offer much promise for replacing this colossal use of fossil fuels with renewables; these fuel cells produce negligible emissions and have a mileage and filling time equal to a r......% of the annual automotive vehicle production. Lowering the Pt loading in a fuel cell to a sustainable level requires the reactivity of Pt to be tuned so that it accelerates oxygen reduction more effectively (3). Two reports in this issue address this challenge (4, 5)....... to a regular gasoline car. However, current fuel cells require 0.25 g of platinum (Pt) per kilowatt of power (2) as catalysts to drive the electrode reactions. If the entire global annual production of Pt were devoted to fuel cell vehicles, fewer than 10 million vehicles could be produced each year, a mere 10...

  1. The fuel cell; La pile a combustible

    Energy Technology Data Exchange (ETDEWEB)

    Boursin, P.

    2005-07-01

    This document is an exhaustive review of the history of fuel cells from 1802 to 2004. It focusses mainly on the automotive applications and supplies many technical details about each prototype of fuel cell and/or vehicle. (J.S.)

  2. Fuel cell hybrid drive train test facility

    NARCIS (Netherlands)

    J. Bruinsma; I. Zafina; H. Bosma; Edwin Tazelaar; Bram Veenhuizen

    2009-01-01

    Fuel cells are expected to play an important role in the near future as prime energy source on board of road-going vehicles. In order to be able to test all important functional aspects of a fuel cell hybrid drive train, the Automotive Institute of the HAN University has decided to realize a

  3. Automotive History and Development of the Automobile; Automotive Mechanics I: 9043.01.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    The automotive history and development of the automobile course is designed to familiarize the beginning student with basic concepts common to the automobile history and general information that is required for successful advancement in the automotive mechanics field. A course outline is provided and seven pages of post-tests are included in the…

  4. Automotive Electrical and Electronic Systems I; Automotive Mechanics 2: 9045.03.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    The automotive electrical and electronic system I course is designed as one of a group of quinmester courses offered in the field of automotive mechanics. General information will be given along with technical knowledge, basic skills, attitudes and values that are required for job entry level. The nine week (135 clock hour) course overcomes some…

  5. Secondary-Postsecondary Curriculum Development in Automotive Mechanics. Automotive Electrical Competencies. Final Report.

    Science.gov (United States)

    Hoepner, Ronald

    Developed as part of a competency-based curriculum in automotive mechanics which is usable by students at both the secondary and postsecondary levels, this learning package focuses on automotive electrical systems. It is the first unit to be published in a series of eight which will cover the eight subject areas on the national certification…

  6. 75 FR 34170 - Plastic Omnium Automotive Exteriors, LLC, Anderson, SC; Plastic Omnium Automotive Exteriors, LLC...

    Science.gov (United States)

    2010-06-16

    ... Employment and Training Administration Plastic Omnium Automotive Exteriors, LLC, Anderson, SC; Plastic Omnium... Assistance on March 18, 2010, applicable to workers of Plastic Omnium Automotive Exteriors, LLC, Anderson... have occurred involving workers in support of the Anderson, South Carolina location of Plastic Omnium...

  7. The impact of global warming on the automotive industry

    Science.gov (United States)

    Hannappel, Ralf

    2017-08-01

    One cause of global warming of the earth's atmosphere is the emission of human made gases (methane, CO2, nitrous oxygen, etc.) into the environment. Of the total global CO2 emissions the transportation sector contributes to about 14%. In order to control the emissions of the automotive sector, in all major countries (USA, Europe, China, Japan) of the world, tough emissions targets were being set to reduce the vehicle traffic's contribution of CO2. These are derived from the global climate conference' target to limit the maximum temperature increase of the earth of 2 degrees Celsius until 2100. In order to achieve these stringent targets the automotive industry will face a major change in its drivetrain. It will move from combustion to electrical engines. The technical realization of these engines will most likely be battery and fuel cell driven propulsion systems. In order to achieve that transition a major effort is required in 4 industrial areas, i.e. growing electrical charging infrastructure, lowering battery cost, increasing the battery-electric vehicle ranges and developing new environmental friendly hydrogen production methods.

  8. FUEL PRICES AND CAR SALES

    OpenAIRE

    Vlad Cârstea

    2008-01-01

    Automotive industry is a very important economic sector that is highly responsive to changes in the world economy. The fuel price is the biggest enemy of car manufacturers. This is a compared analysis between Europe and Romania regarding new car registrations.

  9. Fuel cells: principles, types, fuels, and applications.

    Science.gov (United States)

    Carrette, L; Friedrich, K A; Stimming, U

    2000-12-15

    During the last decade, fuel cells have received enormous attention from research institutions and companies as novel electrical energy conversion systems. In the near future, they will see application in automotive propulsion, distributed power generation, and in low power portable devices (battery replacement). This review gives an introduction into the fundamentals and applications of fuel cells: Firstly, the environmental and social factors promoting fuel cell development are discussed, with an emphasis on the advantages of fuel cells compared to the conventional techniques. Then, the main reactions, which are responsible for the conversion of chemical into electrical energy in fuel cells, are given and the thermodynamic and kinetic fundamentals are stated. The theoretical and real efficiencies of fuel cells are also compared to that of internal combustion engines. Next, the different types of fuel cells and their main components are explained and the related material issues are presented. A section is devoted to fuel generation and storage, which is of paramount importance for the practical aspects of fuel cell use. Finally, attention is given to the integration of the fuel cells into complete systems. © 2000 WILEY-VCH Verlag GmbH, Weinheim, Fed. Rep. of Germany.

  10. Adsorptive Waste Heat Based Air-Conditioning Control Strategy for Automotives

    OpenAIRE

    Indrasen Raghupatruni; Michael Glora; Ralf Diekmann; Thomas Demmer

    2015-01-01

    As the trend in automotive technology is fast moving towards hybridization and electrification to curb emissions as well as to improve the fuel efficiency, air-conditioning systems in passenger cars have not caught up with this trend and still remain as the major energy consumers amongst others. Adsorption based air-conditioning systems, e.g. with silica-gel water pair, which are already in use for residential and commercial applications, are now being considered as a tec...

  11. Change in the automotive industry; Fordonsindustrin i foeraendring

    Energy Technology Data Exchange (ETDEWEB)

    Fjaellstroem, Mikael [Swedish Energy Agency, Eskilstuna (Sweden); Pohl, Hans [Sycon Energikonsult AB, Malmoe (Sweden); Liljemark, Stefan [SwedPower AB (Sweden); Leander, Aasa [Swedish Energy Agency, Eskilstuna (Sweden); Maruo, Kanehira [Chalmers Univ. of Tech., Goeteborg (Sweden); Waldenby, Torbjoern [JIC Consulting AB, Goeteborg (Sweden); Mellgren, Henry [Fordonskomponentgruppen, Goeteborg (Sweden)

    2002-04-01

    The 'Change in the Automotive Industry' investigation was initiated by the Swedish Energy Agency in the autumn of 2000. The objective has been to illuminate and analyse technical developments in respect of the use of electricity in vehicles, not only for various ancillary systems but also for propulsion. A number of Swedish businesses that have, or could have, links with the automotive industry have been investigated. The main aim has been to attempt to identify the opportunities for the industry to meet and benefit from the changes. A total of 14 businesses have been visited, and a further 29 companies have replied to a survey questionnaire on the theme. Business intelligence shows that a great deal of work is being done on the use of electricity for automotive propulsion, in everything from battery vehicles, via electric hybrid vehicles to fuel cell vehicles. In terms of development, the Japanese manufacturers are in the lead, while the USA constitutes the largest single driving force behind development. The technical development requires a greater understanding within several new disciplines, and leads to major changes between different industry sectors. The results show that Sweden possesses world class expertise in several of the fields that can become very important for tomorrow's automotive industry. At the same time, the companies expect difficulties in recruiting personnel qualified in the appropriate disciplines, such as development and design. There is, therefore, a clear risk that the present-day expertise will progressively fade away if nothing is done.There is a wide range of awareness of the greater use of electricity in vehicles. However, in principle, all companies feel that development towards new drive trains will proceed rapidly. Most of the companies are also very interested in descriptions and analyses of the state of development. The general conclusion of the work is that there are excellent prospects for Swedish industry to

  12. Proton Exchange Membrane Fuel Cells Applied for Transport Sector

    DEFF Research Database (Denmark)

    Hosseinzadeh, Elham; Rokni, Masoud

    2010-01-01

    A thermodynamic analysis of a PEMFC (proton exchange membrane fuel cell) is investigated. PEMFC may be the most promising technology for fuel cell automotive systems, which is operating at quite low temperatures, (between 60 to 80℃). In this study the fuel cell motive power part of a lift truck has...

  13. Laboratory Application and Demonstration of Automotive Oxygen Sensors

    Science.gov (United States)

    Schober, T.; Friedrich, J.

    1999-12-01

    The application and demonstration of automotive oxygen (lambda) sensors in the laboratory is discussed. After a presentation of the electrochemical principle, selected experiments are outlined, which cover a broad spectrum of possible applications. In addition to the possibility of measuring partial pressures of oxygen, the use of these sensors in a fuel cell mode is described. Closely related to the latter case is the measurement of water vapor pressures in certain gas mixtures. Passing currents through the sensors allows removing (or adding) trace oxygen from (to) gas streams. In this way, low pO2 (10-22 bar) Ar-H2O-H2 mixtures may be generated. Electrochemical pumping of oxygen from CO2 gas streams allows the production of low pO2 CO2-CO mixtures.

  14. 5th International Conference on Sustainable Automotive Technologies

    CERN Document Server

    Subic, Aleksandar; Trufin, Ramona

    2014-01-01

    This book captures selected peer reviewed papers presented at the 5th International Conference on Sustainable Automotive Technologies, ICSAT 2013, held in Ingolstadt, Germany. ICSAT is the state-of-the-art conference in the field of new technologies for transportation. The book brings together the work of international researchers and practitioners under the following interrelated headings: fuel transportation and storage, material recycling, manufacturing and management costs, engines and emission reduction. The book provides a very good overview of research and development activities focused on new technologies and approaches capable of meeting the challenges to sustainable mobility. About the Editors: Prof. Dr. Jörg Wellnitz is the Dean of the Faculty of Mechanical Engineering, Technische Hochschule Ingolstadt, Germany. Prof. Dr. Aleksandar Subic is the Head of the School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Australia. Ramona Trufin, M.A. is the coordinator of the Facul...

  15. Enabling Automotive Innovation: Tales from a Physicist in Industry

    Science.gov (United States)

    Pinkerton, Frederick

    Measurements and instrumentation play an obvious and critical technical role in the automotive industry to assure compliance with government and industry standards such as emissions and fuel economy. Less obvious and equally critical is the role they play in innovative materials for future transportation needs. In today's open innovation environment, where research is distributed among industrial, academic, and government lab partners, the ability to capture, validate, and incorporate both internal and external inventions combines a deep knowledge base and the research tools to evaluate advanced materials and processes. Examples of the impact of measurements and instrumentation on internal, external, and shared research will be given from the experiences of the author and his research colleagues.

  16. Storing electricity, the technological challenge of the automotive sector

    International Nuclear Information System (INIS)

    Moulet, C.

    2010-01-01

    The search for alternatives to the internal combustion engine for motor vehicles may be nothing new, but the present focus on environmental issues (dwindling fossil fuel reserves, growing awareness of the environmental impact of the internal combustion engine, etc.) makes it more topical than ever. It is no coincidence that most manufacturers and OEMs on the automotive market, and many research centers, are studying the use of batteries and fuel cells as a means of developing greener, sustainable transport solutions for the future. The European Union is considering ways of compelling manufacturers to market vehicles that are more fuel-efficient at a time when the members of the European Automobile Manufacturers Association, unlike their counterparts in Japan, are failing to meet the targets defined in voluntary agreements. Through their sales of hybrid vehicles, Japanese manufacturers have lent credibility to the notion of a market for electrified vehicles. In this way, market constraints (environmental impact of the internal combustion engine, the cost of fossil fuel, consumers, and national or European lawmakers) will push the automotive industry into marketing 'low-carbon' vehicles in the very short term. Manufacturers' product plans reveal that a wave of electrified products can be expected on the market in 2015. That implies a significant R and D effort between now and 2012, with demonstrator vehicles up and running by 2013-2014 at the latest. So now is a crucial time for research organisations to position themselves in preparation for this emerging market. Industry is hoping for technological progress in areas that cut across these varying degrees of hybridisation and electrification, namely the storage and management of electrical energy and power electronics. It is these areas that will be at the heart of research programs. In these highly competitive times, efforts should focus on: - Lowering costs (by a factor of 5 to 10 for fuel cells and 2 to 4 for

  17. Green competitiveness research on Chinese automotive enterprises

    Directory of Open Access Journals (Sweden)

    Yuanhui Li

    2014-05-01

    Full Text Available Purpose: More and more executives of automobileindustry in China start to recognize the concept of green competitiveness recently. However, relatively less research attention has been devoted to the consideration of measurement. This paper aims to find empirical approach to quantify green competitiveness for automotive enterprises. The connotation of green competitiveness is explored and one suite of evaluation index system has been proposed with four dimensions including environmental, resource, capability and knowledge.Design/methodology/approach: By introducing the factor analysis method, green competitiveness has been measured through an empirical analysis of 24 automotive enterprises within China.Findings: The results indicate that those elements, such as enterprise resource possession and utilization; environment, responsibility and knowledge; profitability; management efficiency, have significant effect on the green competitiveness for automotive enterprises. The further analysis also unveils the advantages and disadvantages of green competitiveness for each company and the direction for improvement.Research limitations/implications: Guide regulators and managers of automobile industry to take some measures to enhance their green competitive advantage.Practical implications: Provide practical methods to measure green competitiveness for automotive enterprises.Originality/value: This paper proposes an evaluation index system of green competitiveness for automotive enterprises. The suggestions of our research will be beneficial to enterprise executives and industry regulators.

  18. Computational design of an automotive twist beam

    Directory of Open Access Journals (Sweden)

    Benki Aalae

    2016-07-01

    Full Text Available In recent years, the automotive industry has known a remarkable development in order to satisfy the customer requirements. In this paper, we will study one of the components of the automotive which is the twist beam. The study is focused on the multicriteria design of the automotive twist beam undergoing linear elastic deformation (Hooke׳s law. Indeed, for the design of this automotive part, there are some criteria to be considered as the rigidity (stiffness and the resistance to fatigue. Those two criteria are known to be conflicting, therefore, our aim is to identify the Pareto front of this problem. To do this, we used a Normal Boundary Intersection (NBI algorithm coupling with a radial basis function (RBF metamodel in order to reduce the high calculation time needed for solving the multicriteria design problem. Otherwise, we used the free form deformation (FFD technique for the generation of the 3D shapes of the automotive part studied during the optimization process.

  19. Onboard fuel processor for PEM fuel cell vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Bowers, Brian J.; Zhao, Jian L.; Ruffo, Michael; Khan, Rafey; Dattatraya, Druva; Dushman, Nathan [Nuvera Fuel Cells, Inc, 20 Acorn Park, Cambridge, MA 02140 (United States); Beziat, Jean-Christophe; Boudjemaa, Fabien [Renault, Service 64240 - FR TCR GRA 0 75, Technocentre Renault - 1 avenue du Golf, 78288 Guyancourt (France)

    2007-07-15

    To lower vehicle greenhouse gas emissions, many automotive companies are exploring fuel cell technologies, which combine hydrogen and oxygen to produce electricity and water. While hydrogen storage and infrastructure remain issues, Renault and Nuvera Fuel Cells are developing an onboard fuel processor, which can convert a variety of fuels into hydrogen to power these fuel cell vehicles. The fuel processor is now small enough and powerful enough for use on a vehicle. The catalysts and heat exchangers occupy 80 l and can be packaged with balance of plant controls components in a 150-l volume designed to fit under the vehicle. Recent systems can operate on gasoline, ethanol, and methanol with fuel inputs up to 200 kWth and hydrogen efficiencies above 77%. The startup time is now less than 4 min to lower the CO in the hydrogen stream to the target value for the fuel cell. (author)

  20. IPI tax relief policy and its impact on automotive and related sectors

    Directory of Open Access Journals (Sweden)

    Luiz Antônio Abrantes

    2017-09-01

    Full Text Available The policy of IPI tax relief in the automotive industry came from the need of answers to the Global Financial Crisis of 2008, which affected Brazil. This way, Brazilian Government set the reduction of the percentages of rates applied to automotive products and related sectors, according to several factors such as engine power, fuel type and production site, in order to restore the sector demand and stimulate the economy. In this context, this work aims to evaluate the implications of IPI tax relief policy, since 2009, on the turnover of joint-stock companies of the automotive and related sectors. The methodology was a multiple regression analysis model with Dynamic Panel data, in order to explain the variations of companies' turnover in the sector, regarding IPI tax relief. The data used were of 84 companies of this sector, for the period from 1998 to 2015, based on the software Economática. The results showed a decrease of IPI tax collection in the periods of relief, both in general and specific scope. In addition, we verified that the adoption of the policy had a negative influence on the turnover of the evaluated companies. Thus, we concluded that the tax policy under analysis did not contribute to an increase of automotive sector companies' turnover.

  1. Recovery of platinum-group metals (PGMS from spent automotive catalysts: Part II: Automotive catalysts: Structures and principle of operation

    Directory of Open Access Journals (Sweden)

    Dimitrijević Mile D.

    2015-01-01

    Full Text Available Catalytic converters are incorporated into motor vehicle emission systems (passenger cars, trucks and other motor vehicles, as well as civil and agricultural machines, as of lately to reduce air pollution as well as to meet the emission standards. Their purpose is to convert toxic emissions generated by combustion of liquid fossil fuels into less harmful products. In catalytic converters, rhodium is used for the reduction of gasses, whereas platinum and palladium are used for the oxidation of gasses. This paper presents the structure and operating principle of automotive catalysts in view of the fact that cars are the most prevalent motor vehicles worldwide and due to the fact that the production of cars with gasoline and diesel engines will dominate until at least 2020.

  2. Automotive Radar Sensors in Silicon Technologies

    CERN Document Server

    Jain, Vipul

    2013-01-01

    This book presents architectures and design techniques for mm-wave automotive radar transceivers. Several fully-integrated transceivers and receivers operating at 22-29 GHz and 77-81 GHz are demonstrated in both CMOS and SiGe BiCMOS technologies. Excellent performance is achieved indicating the suitability of silicon technologies for automotive radar sensors.  This book bridges an existing gap between information available on dependable system/architecture design and circuit design.  It provides the background of the field and detailed description of recent research and development of silicon-based radar sensors.  System-level requirements and circuit topologies for radar transceivers are described in detail. Holistic approaches towards designing radar sensors are validated with several examples of highly-integrated radar ICs in silicon technologies. Circuit techniques to design millimeter-wave circuits in silicon technologies are discussed in depth.  Describes concepts and fundamentals of automotive rada...

  3. Best Practices in School-to-Careers: The Automotive Industry.

    Science.gov (United States)

    National Employer Leadership Council, Washington, DC.

    This document highlights the school-to-careers (STC) partnerships connecting workplace experiences to classroom learning to prepare students for successful employment in the automotive industry. First, the current state of the automotive industry is reviewed and the role of STC in addressing automotive service needs is explained. Next, the…

  4. Automotive sensors: past, present and future

    International Nuclear Information System (INIS)

    Prosser, S J

    2007-01-01

    This paper will provide a review of past, present and future automotive sensors. Today's vehicles have become highly complex sophisticated electronic control systems and the majority of innovations have been solely achieved through electronics and the use of advanced sensors. A range of technologies have been used over the past twenty years including silicon microengineering, thick film, capacitive, variable reluctance, optical and radar. The automotive sensor market continues to grow with respect to vehicle production level in recognition of the transition to electronically controlled electrically actuated systems. The environment for these sensors continues to be increasingly challenging with respect to robustness, reliability, quality and cost

  5. Fatigue life of automotive rubber jounce bumper

    International Nuclear Information System (INIS)

    Sidhu, R S; Ali, Aidy

    2010-01-01

    It is evident that most rubber components in the automotive industry are subjected to repetitive loading. Vigorous research is needed towards improving the safety and reliability of the components. The study was done on an automotive rubber jounce bumper with a rubber hardness of 60 IRHD. The test was conducted in displacement-controlled environment under compressive load. The existing models by Kim, Harbour, Woo and Li were adopted to predict the fatigue life. The experimental results show strong similarities with the predicted models.

  6. Nanotechnology impact on the automotive industry.

    Science.gov (United States)

    Wong, Kaufui V; Paddon, Patrick A

    2014-01-01

    Nanotechnology has been implemented widely in the automotive industry. This technology is particularly useful in coatings, fabrics, structural materials, fluids, lubricants, tires, and preliminary applications in smart glass/windows and video display systems. A special sub-class of improved materials, alternative energy, has also seen a boost from advances in nanotechnology, and continues to be an active research area. A correlation exists in the automotive industry between the areas with increased nanotechnology incorporation and those with increased profit margins via improvements and customer demands.

  7. Proceedings of the international symposium on alcohol fuel technology: methanol and ethanol

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-07-01

    The papers presented dealt with the following topics: international situation and economic and political aspects, use of alcohol fuels as automotive fuels, production of methanol and methyl fuels, production of ethanol, methanol application and modeling, alcohol fuel optimization, and environmental considerations. Each paper was prepared for introduction into the EDB data base. (JSR)

  8. Status of solid polymer electrolyte fuel cell technology and potential for transportation applications

    Science.gov (United States)

    McElroy, J. F.; Nuttall, L. J.

    The solid polymer electrolyte (SPE) fuel cell represents the first fuel cell technology known to be used operationally. Current activities are mainly related to the development of a space regenerative fuel cell system for energy storage on board space stations, or other large orbiting vehicles and platforms. During 1981, a study was performed to determine the feasibility of using SPE fuel cells for automotive or other vehicular applications, using methanol as the fuel. The results of this study were very encouraging. Details concerning a conceptual automotive fuel cell power plant study are discussed, taking into account also a layout of major components for compact passenger car installation.

  9. Profiles of Major Suppliers to the Automotive Industry : Vol. 5. Multinational Automotive Parts and Components Suppliers

    Science.gov (United States)

    1982-08-01

    This study summarizes extensive information collected over a two-year period (October 1978 to October 1980) on suppliers of parts and components, materials, and machine tools to the automotive industry in the United States. The objective of the study...

  10. Profiles of Major Suppliers to the Automotive Industry : Vol. 6. Foreign Automotive Parts and Components Suppliers.

    Science.gov (United States)

    1982-08-01

    This study summarizes extensive information collected over a two-year period (October 1978 to October 1980) on suppliers of parts and components, materials, and machine tools to the automotive industry in the United States. The objective of the study...

  11. Determining Role of Temperature Chart while Evaluating Specific Expenses of Organic Fuel

    Directory of Open Access Journals (Sweden)

    A. P. Nesenchouk

    2009-01-01

    Full Text Available The paper considers designing principles of operational space continuous heating and heat-treating furnaces at mechanical engineering, automotive and tractor enterprises in theRepublicofBelarus. A role of temperature chart on heating metallic charge while evaluating specific expenses of organic fuel in heating and heat-treating furnaces of mechanical engineering, automotive and tractor industries. 

  12. Market Opportunities for Automotive Components Used in Non-automotive Applications Manufacturing : Estonian Industrial Market

    OpenAIRE

    Kalajärv, Jaana

    2012-01-01

    This thesis examines the opportunities available for automotive components in the Esto-nian non-automotive industrial market. The literature review part is mainly covers the theory of marketing research, because of the approach chosen for this paper. Only small part of marketing research process is re-searched closer in literature review section, because of the scope of the research. Three most relevant steps for the thesis are chosen from research process for further more in-vestigation,...

  13. Automotive Mechanics Occupational Performance Survey. Interim Report.

    Science.gov (United States)

    Borcher, Sidney D.; Leiter, Paul B.

    The purpose of this federally-funded interim report is to present the results of a task inventory analysis survey of automotive mechanics completed by project staff within the Instructional Systems Design Program at the Center for Vocational and Technical Education. Intended for use in curriculum development for vocational education programs in…

  14. Orientation: Automotive Mechanics Instructional Program. Block 1.

    Science.gov (United States)

    O'Brien, Ralph D.

    The first six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in the basic theory and practice of a beginning course at the secondary and post-secondary level. The material, as organized, is a suggested sequence of instruction…

  15. Basic Automotive Mechanics. Florida Vocational Program Guide.

    Science.gov (United States)

    University of South Florida, Tampa. Dept. of Adult and Vocational Education.

    This program guide identifies primary concerns in the organization, operation, and evaluation of a basic automotive mechanics program. It is designed for local school district and community college administrators, instructors, program advisory committees, and regional coordinating councils. The guide begins with the Dictionary of Occupational…

  16. Automotive Body Repair. Performance Objectives. Basic Course.

    Science.gov (United States)

    Lang, Thomas

    Several intermediate performance objectives and corresponding criterion measures are listed for each of 15 terminal objectives for a basic automotive body repair and refinishing course. The materials were developed for a two-semester (2 hours daily) course for organized classroom and shop experiences designed to enable the student to develop…

  17. Automotive Body Repair. Performance Objectives. Intermediate Course.

    Science.gov (United States)

    Lang, Thomas

    Several intermediate performance objectives and corresponding criterion measures are listed for each of 10 terminal objectives for an intermediate automotive body repair and refinishing course. The materials were developed for a two-semester (3 hours daily) course for specialized classrooms, shop, and practical experiences designed to enable the…

  18. A listening test system for automotive audio

    DEFF Research Database (Denmark)

    Christensen, Flemming; Geoff, Martin; Minnaar, Pauli

    2005-01-01

    This paper describes a system for simulating automotive audio through headphones for the purposes of conducting listening experiments in the laboratory. The system is based on binaural technology and consists of a component for reproducing the sound of the audio system itself and a component...

  19. PERFORMANCE OF AN AUTOMOTIVE BUMPER FROM LALLOH ...

    African Journals Online (AJOL)

    The work presented here is the production of an automotive Bumper from Lalloh plant (Corchorus tridenL.) fibre reinforced epoxy composite and its performance evaluation using the drop weight test method. An impact test was carried out on the bumper using a test rig modeled after the Dynatup Model 8150 drop weight test ...

  20. The stretch zone of automotive steel sheets

    Indian Academy of Sciences (India)

    on steel grade, on the rolling direction as well as on the loading rate. Stretch zones ... This interaction is demonstrated at a fracture surface as a bounded transition between initiatory crack (e.g., fatigue) and either ... The materials examined in this study are three grades of thin automotive steel sheets: XSG,. HR 45 and DP.

  1. International Conference on Vehicle and Automotive Engineering

    CERN Document Server

    Bolló, Betti

    2017-01-01

    This book presents the proceedings of the first vehicle engineering and vehicle industry conference. It captures the outcome of theoretical and practical studies as well as the future development trends in a wide field of automotive research. The themes of the conference include design, manufacturing, economic and educational topics.

  2. Training Issues for the European Automotive Industry

    NARCIS (Netherlands)

    Dankbaar, B.

    1996-01-01

    Provides an overview of the results of an investigation carried out for the European Commission. Aims to identify themes and issues in the field of continuing training in the European automotive industry. A large number of interviews were carried out in all the major car manufacturing countries of

  3. Training issues for the European automotive industry

    NARCIS (Netherlands)

    Dankbaar, B.

    1999-01-01

    Provides an overview of the results of an investigation carried out for the European Commission. Aims to identify themes and issues in the field of continuing training in the European automotive industry. A large number of interviews were carried out in all the major car manufacturing countries of

  4. Graduate Automotive Technology Education (GATE) Center for Hybrid Electric Drivetrains and Control Strategies

    Energy Technology Data Exchange (ETDEWEB)

    David Holloway

    2005-09-30

    Beginning the fall semester of 1999, The University of Maryland, Departments of Mechanical and Electrical Engineering and the Institute for Systems Research served as a U.S. Department of Energy (USDOE) Graduate Automotive Technology Education (GATE) Center for Hybrid Electric Drivetrains and Control Strategies. A key goal was to produce a graduate level education program that educated and prepared students to address the technical challenges of designing and developing hybrid electric vehicles, as they progressed into the workforce. A second goal was to produce research that fostered the advancement of hybrid electric vehicles, their controls, and other related automotive technologies. Participation ended at the University of Maryland after the 2004 fall semester. Four graduate courses were developed and taught during the course of this time, two of which evolved into annually-taught undergraduate courses, namely Vehicle Dynamics and Control Systems Laboratory. Five faculty members from Mechanical Engineering, Electrical Engineering, and the Institute for Systems Research participated. Four Ph.D. degrees (two directly supported and two indirectly supported) and seven Master's degrees in Mechanical Engineering resulted from the research conducted. Research topics included thermoelectric waste heat recovery, fuel cell modeling, pre- and post-transmission hybrid powertrain control and integration, hybrid transmission design, H{sub 2}-doped combustion, and vehicle dynamics. Many of the participating students accepted positions in the automotive industry or government laboratories involved in automotive technology work after graduation. This report discusses the participating faculty, the courses developed and taught, research conducted, the students directly and indirectly supported, and the publication list. Based on this collection of information, the University of Maryland firmly believes that the key goal of the program was met and that the majority of the

  5. 76 FR 19684 - Automotive Fuel Ratings Certification and Posting

    Science.gov (United States)

    2011-04-08

    ... the ``Octane Certification and Posting Rule''), in 1979 in accordance with the Petroleum Marketing... errors.\\18\\ \\15\\ The Rule currently provides specific requirements for E85, a mix of gasoline and ethanol... (.48 cm) from the side edges of the label. If you wish to change the dimensions of this one principal...

  6. Development of excise on automotive fuels in the neighbouring countries

    International Nuclear Information System (INIS)

    Bleijenberg, A.N.; Janse, P.

    1994-04-01

    The political options for the Netherlands to implement the pricing policy for road traffic by means of an increase of excise, as formulated in the Second Transport Structure Plan (SVV-2), are limited by the excise level in neighbouring countries. Therefore, a study on the title subject has been carried out. First, an overview is given of the historical development of sales prices since 1980 for Belgium, Germany, Luxembourg and France with special attention for the large price differences. Next, insight into the effects of a price difference at the borders is given. Subsequently the development in the policy of the European Union with regard to harmonization of excise tariffs is discussed. Environmental organizations in Belgium and Luxembourg were contacted to learn about the expected development of excises in those countries. 5 figs., 6 tabs., 4 appendices, 10 refs

  7. AGT-102 automotive gas turbine

    Science.gov (United States)

    1981-01-01

    Development of a gas turbine powertrain with a 30% fuel economy improvement over a comparable S1 reciprocating engine, operation within 0.41 HC, 3.4 CO, and 0.40 NOx grams per mile emissions levels, and ability to use a variety of alternate fuels is summarized. The powertrain concept consists of a single-shaft engine with a ceramic inner shell for containment of hot gasses and support of twin regenerators. It uses a fixed-geometry, lean, premixed, prevaporized combustor, and a ceramic radial turbine rotor supported by an air-lubricated journal bearing. The engine is coupled to the vehicle through a widerange continuously variable transmission, which utilizes gearing and a variable-ratio metal compression belt. A response assist flywheel is used to achieve acceptable levels of engine response. The package offers a 100 lb weight advantage in a Chrysler K Car front-wheel-drive installation. Initial layout studies, preliminary transient thermal analysis, ceramic inner housing structural analysis, and detailed performance analysis were carried out for the basic engine.

  8. Design and development of a continuously variable ratio transmission for automotive vehicles. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-09-30

    Work accomplished between July 1974 and October 1978 in a program directed toward the design and development of a continuously variable ratio transmission (CVT) for an automotive vehicle is reported. The following major accomplishments were achieved: the laboratory and mathematical projections establishing the viability of the program and the predicted attainment of the primary goal of fuel economy were verified; the proposed Concept Demonstration prototype hydromechanical transmission (HMT) was completed from design to operation; the HMT was thoroughly tested in the laboratory and on the road and its in-vehicle performance was verified by independent testing laboratories; and design of a second generation Pre-Production HMT has proceeded to the point of confirming the practicality of the automotive HMT size and weight; most of the necessary information has been generated which could permit its production cost/competitiveness to be evaluated. (LCL)

  9. Diffusion of new automotive technologies for improving energy efficiency in Brazil's light vehicle fleet

    International Nuclear Information System (INIS)

    Bastin, Cristina; Szklo, Alexandre; Rosa, Luiz Pinguelli

    2010-01-01

    Historically, Brazil has promoted the development and sales of light duty vehicles running on ethanol (firstly, ethanol-dedicated cars, and recently flexfuel cars). In the 1990s, the country also favored the sales of compact cars to middle and low-income classes. However, in the last years, the profile of vehicles sold in Brazil has converged towards larger and less-efficient vehicles. In 2008, Brazil launched the vehicle labeling program. Based on the outcomes of the historical programs oriented towards the development of automotive innovations, and on a survey conducted with the country's main auto makers, this article evaluates whether the vehicle labeling program will both improve the energy efficiency of light vehicles, and introduce new technologies. Our results indicate that, despite its virtuous intentions, the program will not control the tendency of rising fuel consumption of passenger cars sold in Brazil. Therefore, other policies are needed to boost innovations in Brazil's automotive industry. (author)

  10. Fundamentals of automotive and engine technology standard drives, hybrid drives, brakes, safety systems

    CERN Document Server

    2014-01-01

    Hybrid drives and the operation of hybrid vehicles are characteristic of contemporary automotive technology. Together with the electronic driver assistant systems, hybrid technology is of the greatest importance and both cannot be ignored by today’s car drivers. This technical reference book provides the reader with a firsthand comprehensive description of significant components of automotive technology. All texts are complemented by numerous detailed illustrations. Contents History of the automobile.- History of the Diesel engine.- Areas of use for Diesel engines.- Basic principles of the Diesel engine.- Basic principles of Diesel fuel-injection.- Basic principles of the gasoline engine.- Inductive ignition system.- Transmissions for motor vehicles.- Motor vehicle safety.- Basic principles of vehicle dynamics.- Car braking systems.- Vehicle electrical systems.- Overview of electrical and electronic systems in the vehicle.- Control of gasoline engines.- Control of Diesel engines.- Lighting technology.- Elec...

  11. High-density automotive hydrogen storage with cryogenic capable pressure vessels

    Energy Technology Data Exchange (ETDEWEB)

    Aceves, Salvador M.; Espinosa-Loza, Francisco; Ledesma-Orozco, Elias; Ross, Timothy O.; Weisberg, Andrew H. [Lawrence Livermore National Laboratory, P.O. Box 808, L-792, Livermore, CA 94551 (United States); Brunner, Tobias C.; Kircher, Oliver [BMW Group, Knorrstr. 147, 80788 Munich (Germany)

    2010-02-15

    LLNL is developing cryogenic capable pressure vessels with thermal endurance 5-10 times greater than conventional liquid hydrogen (LH{sub 2}) tanks that can eliminate evaporative losses in routine usage of (L)H{sub 2} automobiles. In a joint effort BMW is working on a proof of concept for a first automotive cryo-compressed hydrogen storage system that can fulfill automotive requirements on system performance, life cycle, safety and cost. Cryogenic pressure vessels can be fueled with ambient temperature compressed gaseous hydrogen (CGH{sub 2}), LH{sub 2} or cryogenic hydrogen at elevated supercritical pressure (cryo-compressed hydrogen, CcH{sub 2}). When filled with LH{sub 2} or CcH{sub 2}, these vessels contain 2-3 times more fuel than conventional ambient temperature compressed H{sub 2} vessels. LLNL has demonstrated fueling with LH{sub 2} onboard two vehicles. The generation 2 vessel, installed onboard an H{sub 2}-powered Toyota Prius and fueled with LH{sub 2} demonstrated the longest unrefueled driving distance and the longest cryogenic H{sub 2} hold time without evaporative losses. A third generation vessel will be installed, reducing weight and volume by minimizing insulation thickness while still providing acceptable thermal endurance. Based on its long experience with cryogenic hydrogen storage, BMW has developed its cryo-compressed hydrogen storage concept, which is now undergoing a thorough system and component validation to prove compliance with automotive requirements before it can be demonstrated in a BMW test vehicle. (author)

  12. Advanced compressed hydrogen fuel storage systems

    International Nuclear Information System (INIS)

    Jeary, B.

    2000-01-01

    Dynetek was established in 1991 by a group of private investors, and since that time efforts have been focused on designing, improving, manufacturing and marketing advanced compressed fuel storage systems. The primary market for Dynetek fuel systems has been Natural Gas, however as the automotive industry investigates the possibility of using hydrogen as the fuel source solution in Alternative Energy Vehicles, there is a growing demand for hydrogen storage on -board. Dynetek is striving to meet the needs of the industry, by working towards developing a fuel storage system that will be efficient, economical, lightweight and eventually capable of storing enough hydrogen to match the driving range of the current gasoline fueled vehicles

  13. Factors affecting diesel fuel degradation using a bespoke high-pressure fuel system rig

    OpenAIRE

    Gopalan, Kesavan; Smith, Christopher; Pickering, Simon; Chuck, Christopher; Bannister, Christopher

    2018-01-01

    Recently, there has been automotive industry-wide impetus to reduce overall diesel vehicle emissions and fuel consumption by increasing fuel injection pressures within common rail systems. Many production fuel injection systems are now capable of delivering rail pressures of 1800-2000 bar with those able to achieve 3000 bar under development. In addition, there has been a gradual increase in the permitted FAME content in EN590 diesel from 5% to 7% with further increases to 10% proposed. With ...

  14. Directions for computational mechanics in automotive crashworthiness

    Science.gov (United States)

    Bennett, James A.; Khalil, T. B.

    1993-01-01

    The automotive industry has used computational methods for crashworthiness since the early 1970's. These methods have ranged from simple lumped parameter models to full finite element models. The emergence of the full finite element models in the mid 1980's has significantly altered the research direction. However, there remains a need for both simple, rapid modeling methods and complex detailed methods. Some directions for continuing research are discussed.

  15. The stretch zone of automotive steel sheets

    Indian Academy of Sciences (India)

    The stretch zone of automotive steel sheets. L' AMBRIŠKO1,∗ and L PEŠEK2. 1Institute of Structural Engineering, Faculty of Civil Engineering,. Technical University of Košice, Vysokoškolská 4, 042 00 Košice, Slovak Republic. 2Department of Materials Science, Faculty of Metallurgy,. Technical University of Košice, Letná 9, ...

  16. Occupational skin diseases in automotive industry workers.

    Science.gov (United States)

    Yakut, Yunus; Uçmak, Derya; Akkurt, Zeynep Meltem; Akdeniz, Sedat; Palanci, Yilmaz; Sula, Bilal

    2014-03-01

    Studies on occupational skin diseases in workers of the automotive industry are few. To investigate the prevalence of occupational skin diseases in workers of the automotive industry. Between September and December 2011, a total of 405 workers from the automotive repair industry in Diyarbakır were interviewed. They were active workers in the repair industry who had been employed for at least six months. Business owners, sellers of spare parts and accounting officers were not included. The employees were examined at their workplaces and the working conditions were observed. Detailed dermatological examination was performed. The mean age of the 405 workers who participated in the study was 27.7 ± 10.3. The mean working time of employees was 13.3 ± 10.4 years. All of the employees were male. Dermatological diseases were not detected in 144 out of 405 workers (35.6%) and at least one condition was diagnosed in 261 (64.4%). The most frequent diagnosis was callus, hyperkeratosis, clavus (27.7%), followed by nail changes (16.8%) and superficial mycoses (12.1%). Contact dermatitis was seen at a rate of 5.9%. Traumatic lesions such as hyperkeratotic lesions and nail changes were found most frequently. Traumatic lesions were common among individuals who did not use gloves. Most nail changes were localized leuconychia, a finding not reported in the studies on automotive industry workers. In accordance with the literature, irritant contact dermatitis was observed in patients with a history of atopy and who had been working for a long time. Occupational skin diseases comprise an important field in dermatology, deserving much attention. Further studies on occupational dermatology are necessary.

  17. Lean tool used in the automotive industry

    Directory of Open Access Journals (Sweden)

    Manuela Ingaldi

    2014-10-01

    Full Text Available In the paper basic concepts of Lean Manufacturing were presented. A company specializing in the development of vehicle dynamics, driver assistance systems, brake systems, seat belt sand electronics technology was characterized. The company is engaged in designing and manufacturing world-class products for the automotive market. The Lean tools used in the production hall, such as Yamazumi chart, machine motion analysis, MTM method and timing, were presented.

  18. INNOVATION LEAN PRINCIPLES IN AUTOMOTIVE GREEN MANUFACTURING

    Directory of Open Access Journals (Sweden)

    Dušan Sabadka

    2014-12-01

    Full Text Available Today, industries such as automotive and manufacturing industries deal with a lot of environmental regulations. Lean is a production strategy whose fundamental principles drive the industry towards a more effective production of goods and services. The eco-efficiency concept is primary to sustainable development and intends to provide more value with less environmental impact. The aim of this study is to identify and explore the contributions of Lean to reduce environmental impacts that naturally result from industrial activity.

  19. Fmcw Mmw Radar For Automotive Longitudinal Control

    OpenAIRE

    David, William

    1997-01-01

    This report presents information on millimeter wave (MMW) radar for automotive longitudinal control. It addresses the fundamental capabilities and limitations of millimeter waves for ranging and contrasts their operation with that of conventional microwave radar. The report analyzes pulsed and FMCW radar configurations, and provides detailed treatment of FMCW radar operating at MMW frequency, its advantages and disadvantages as they relate to range and velocity measurements.

  20. Diode-laser-illuminated automotive lamp systems

    Science.gov (United States)

    Marinelli, Michael A.; Remillard, Jeffrey T.

    1998-05-01

    We have utilized the high brightness of state-of-the-art diode laser sources, and a variety of emerging optical technologies to develop a new class of thin, uniquely styled automotive brake and signal lamps. Using optics based on thin (5 mm) plastic sheets, these lamps provide appearance and functional advantages not attainable with traditional automotive lighting systems. The light is coupled into the sheets using a 1 mm diameter glass fiber, and manipulated using refraction and reflection from edges, surfaces, and shaped cut-outs. Light can be extracted with an efficiency of approximately 50% and formed into a luminance distribution that meets the Society of Automotive Engineers (SAE) photometric requirements. Prototype lamps using these optics have been constructed and are less than one inch in thickness. Thin lamps reduce sheet metal costs, complexity, material usage, weight, and allow for increased trunk volume. In addition, these optics enhance lamp design flexibility. When the lamps are not energized, they can appear body colored, and when lighted, the brightness distribution across the lamp can be uniform or structured. A diode laser based brake lamp consumes seven times less electrical power than one using an incandescent source and has instant on capability. Also, diode lasers have the potential to be 10-year/150,000 mile light sources.

  1. Comparative Environmental Benefits of Lightweight Design in the Automotive Sector: The Case Study of Recycled Magnesium Against CFRP and Steel

    Science.gov (United States)

    D'Errico, Fabrizio; Ranza, Luigi

    A LCA feasibility study was undertaken to determine the environmental impact of an Eco-magnesium process route by recycled chips to manufacture panel for the automotive sector to be compared with comparative scenarios, a non-recycled carbon fiber reinforced polymer (CFRP) and a baseline steel-made component scenario. The objective of this LCA study was to assess the actual benefits of a lightweight solution considering the whole life cycle, including the dirty-phase (i.e. the "cradle-to-exit gate" stage) that impacts differently for the different materials. For this reason the analysis has regarded the net "cradle-to-grave" scenario. Different automotive floor pans were then compared considering the rate of fuel consumption during vehicle operation — i.e. the fuel-mass correlation factor — and the different material substitution factors allowed by the different materials selected.

  2. The Role of Public and Private Protection in Disruptive Innovation: The Automotive Industry and the Emergence of Low-Emission Vehicles

    NARCIS (Netherlands)

    Pinkse, J.; Bohnsack, R.; Kolk, A.

    2014-01-01

    In the automotive industry, the need to move toward more sustainable trajectories of innovation has received much attention. Car manufacturers have started to develop lower emission alternatives for the internal combustion engine, particularly electric, hybrid, and fuel-cell vehicles. They face the

  3. Bosch automotive electrics and automotive electronics. Systems and components, networking and hybrid drive. 5. ed.

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-07-01

    Complete reference guide to automotive electrics and electronics. The significance of electrical and electronic systems has increased considerably in the last few years and this trend is set to continue. The characteristics feature of innovative systems is the fact that they can work together in a network. This requires powerful bus systems that the electronic control units can use to exchange information. Networking and the various bus systems used in motor vehicles are the prominent new topic in the 5th edition of the ''Automotive Electric, Automotive Electronics'' technical manual. The existing chapters have also been updated, so that this new edition brings the reader up to date on the subjects of electrical and electronic systems in the motor vehicle.

  4. Environmental economics of lignin derived transport fuels

    NARCIS (Netherlands)

    Obydenkova, Svetlana V.; Kouris, Panos D.; Hensen, Emiel J. M.; Heeres, Hero J.; Boot, Michael D.

    2017-01-01

    This paper explores the environmental and economic aspects of fast pyrolytic conversion of lignin, obtained from 2G ethanol plants, to transport fuels for both the marine and automotive markets. Various scenarios are explored, pertaining to aggregation of lignin from several sites, alternative

  5. Methanol as fuel: evaluation of atmosphere contamination

    International Nuclear Information System (INIS)

    Alonso, C.D.; Romano, J.; Guardani, M.L.G.

    1991-01-01

    With the beginning of methanol use as automotive fuel in Sao Paulo city, 1990, were realized special measurements of methanol, formaldehyde, ethanol and acetaldehyde in atmosphere. Other indicators of air quality as carbon and ozone monoxide were also observed in this study. (C.M.)

  6. Gaseous fuels: past experiences and future expectations

    NARCIS (Netherlands)

    Steen, M. van der

    1996-01-01

    During the fifties, the use of LPG (Liquefied Petroleum Gas) was promoted in Italy and the Netherlands. The Dutch government promulgated tax regulations which made the use of LPG, available in large quentities as a by-product in the refineries, attractive as an automotive fuel. Dedicated heavy-duty

  7. AUTOMOTIVE MARKET- FROM A GENERAL TO A MARKET SEGMENTATION APPROACH

    Directory of Open Access Journals (Sweden)

    Liviana Andreea Niminet

    2013-12-01

    Full Text Available Automotive market and its corresponding industry are undoubtedly of outmost importance and therefore proper market segmentation is crucial for market players, potential competitors and customers as well. Time has proved that market economic analysis often shown flaws in determining the relevant market, by using solely or mainly the geographic aspect and disregarding the importance of segments on the automotive market. For these reasons we propose a new approach of the automotive market proving the importance of proper market segmentation and defining the strategic groups within the automotive market.

  8. Offshoring trends in the manufacturing process within the automotive industry

    DEFF Research Database (Denmark)

    Simplay, S.; Hansen, Zaza Nadja Lee

    2014-01-01

    This paper investigates offshoring trends in the automotive industry. The research approach consisted of combining empirical findings from case companies with latest research from the field. Empirical data was collected through case studies from 15 automotive organisations based in Europe...... consisting of original equipment manufacturers and engineering service providers. The findings indicated some offshoring trends in the automotive industry. Offshoring in this industry is moving from a manufacturing focus to incorporate large parts of the process, including high-level product development...... with a focus on offshoring in the automotive industry and provides practitioners with information on a cutting-edge trend to the industry...

  9. Evaluation of the Benefits Attributable to Automotive Lighweight Materials Program Research and Development Projects

    Energy Technology Data Exchange (ETDEWEB)

    Das, S.

    2002-01-11

    The purpose of this project is to identify and test methods appropriate for estimating the benefits attributable to research and development (R and D) projects funded by the Automotive Lightweight Materials (ALM) Program of the Office of Advanced Automotive Technologies (OAAT) of the U.S. Department of Energy (DOE). The program focuses on the development and validation of advanced lightweight materials technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. The work supports the goals of the Partnership for a New Generation of Vehicles (PNGV). Up to thirty percent of the improvement required to meet the PNGV goal of tripling vehicle fuel economy and much of its cost, safety, and recyclability goal depend on the lightweight materials. Funded projects range from basic materials science research to applied research in production environments. Collaborators on these projects include national laboratories, universities, and private sector firms, such as leading automobile manufacturers and their suppliers.

  10. In vitro assessment of human airway toxicity from major aldehydes in automotive emissions

    Energy Technology Data Exchange (ETDEWEB)

    Grafstroem, R.C. [Karolinska Inst., Stockholm (Sweden). Inst. of Environmental Medicine

    1997-09-01

    Automotive exhausts can significantly contribute to the levels of reactive aldehydes, including formaldehyde, acetaldehyde and acrolein, in urban air. The use of alcohols as an alternative fuel for gasoline or diesel may further increase these emissions. Since it is unclear if aldehyde inhalation may induce pathological states, including cancer, in human airways, the toxic properties of the above-mentioned aldehydes were studied in cultured target cell types. Each aldehyde modified vital cellular functions in a dose-dependent manner, and invariably inhibited growth and induced abnormal terminal differentiation. Decreases of cellular thiols and increases of intracellular Ca{sup 2+} were observed, and moreover, variable types and amounts of short-lived or persistent genetic damage were induced. The concentrations required for specified levels of a particular type of injury varied up to 10000-fold among the aldehydes. Overall, distinctive patterns of cytopathological activity were observed, which differed both qualitatively and quantitatively among the aldehydes. Finally, aldehydes inhibited DNA repair processes and increased cytotoxicity and mutagenesis in synergy with other known toxicants, indicating that aldehydes may also enhance damage by other constituents in automotive exhausts. In summary, the aldehydes, notably {sup m}u{sup M}-mM formaldehyde, caused pathological effects and induced mechanisms that relate to acute toxicity and cancer development in airway epithelial cells. Since `no-effect` levels may not exist for carcinogenic agents, the overall results support a need for elimination of aldehydes in automotive exhausts. 41 refs

  11. Advanced high temperature materials for the energy efficient automotive Stirling engine

    International Nuclear Information System (INIS)

    Titran, R.H.; Stephens, J.R.

    1984-01-01

    The Stirling engine is under investigation jointly by the Department of Energy and NASA Lewis as an alternative to the internal combustion engine for automotive applications. The Stirling engine is an external combustion engine that offers the advantage of high fuel economy, low emissions, low noise, and low vibrations compared to current internal combustion automotive engines. The most critical component from a materials viewpoint is the heater head consisting of the cylinders, heating tubes, and regenerator housing. Materials requirements for the heater head include compatibility with hydrogen, resistance to hydrogen permeation, high temperature oxidation/corrosion resistance, and high temperature creep-rupture and fatigue properties. A continuing supporting materials research and technology program has identified the wrought alloys CG-27 and 12RN72, and the cast alloys XF-818 and NASAUT 4G-A1 as candidate replacements for the cobalt containing alloys used in current prototype engines. Based on the materials research program in support of the automotive Stirling engine it is concluded that manufacture of the engine is feasible from low cost iron-base alloys rather than the cobalt alloys used in prototype engines. This paper presents results of research that led to this conclusion

  12. Non-Destructive Thermography Analysis of Impact Damage on Large-Scale CFRP Automotive Parts

    Science.gov (United States)

    Maier, Alexander; Schmidt, Roland; Oswald-Tranta, Beate; Schledjewski, Ralf

    2014-01-01

    Laminated composites are increasingly used in aeronautics and the wind energy industry, as well as in the automotive industry. In these applications, the construction and processing need to fulfill the highest requirements regarding weight and mechanical properties. Environmental issues, like fuel consumption and CO2-footprint, set new challenges in producing lightweight parts that meet the highly monitored standards for these branches. In the automotive industry, one main aspect of construction is the impact behavior of structural parts. To verify the quality of parts made from composite materials with little effort, cost and time, non-destructive test methods are increasingly used. A highly recommended non-destructive testing method is thermography analysis. In this work, a prototype for a car’s base plate was produced by using vacuum infusion. For research work, testing specimens were produced with the same multi-layer build up as the prototypes. These specimens were charged with defined loads in impact tests to simulate the effect of stone chips. Afterwards, the impacted specimens were investigated with thermography analysis. The research results in that work will help to understand the possible fields of application and the usage of thermography analysis as the first quick and economic failure detection method for automotive parts. PMID:28788464

  13. Non-Destructive Thermography Analysis of Impact Damage on Large-Scale CFRP Automotive Parts

    Directory of Open Access Journals (Sweden)

    Alexander Maier

    2014-01-01

    Full Text Available Laminated composites are increasingly used in aeronautics and the wind energy industry, as well as in the automotive industry. In these applications, the construction and processing need to fulfill the highest requirements regarding weight and mechanical properties. Environmental issues, like fuel consumption and CO2-footprint, set new challenges in producing lightweight parts that meet the highly monitored standards for these branches. In the automotive industry, one main aspect of construction is the impact behavior of structural parts. To verify the quality of parts made from composite materials with little effort, cost and time, non-destructive test methods are increasingly used. A highly recommended non-destructive testing method is thermography analysis. In this work, a prototype for a car’s base plate was produced by using vacuum infusion. For research work, testing specimens were produced with the same multi-layer build up as the prototypes. These specimens were charged with defined loads in impact tests to simulate the effect of stone chips. Afterwards, the impacted specimens were investigated with thermography analysis. The research results in that work will help to understand the possible fields of application and the usage of thermography analysis as the first quick and economic failure detection method for automotive parts.

  14. 77 FR 34854 - Prevailing Rate Systems; Special Wage Schedules for Nonappropriated Fund Automotive Mechanics

    Science.gov (United States)

    2012-06-12

    ...-AM63 Prevailing Rate Systems; Special Wage Schedules for Nonappropriated Fund Automotive Mechanics... for the Department of Defense's (DOD's) nonappropriated fund (NAF) automotive mechanics. These special... practice for compensating NAF automotive mechanics with current prevailing pay practices in the private...

  15. Numerical Investigation on the Performance of an Automotive Thermoelectric Generator with Exhaust-Module-Coolant Direct Contact

    Science.gov (United States)

    Wang, Yiping; Tang, Yulin; Deng, Yadong; Su, Chuqi

    2017-12-01

    Energy conservation and environmental protection have typically been a concern of research. Researchers have confirmed that in automotive engines, just 12-25% of the fuel energy converts into effective work and 30-40% gets wasted in the form of exhaust. Saidur et al. (Energy Policy 37:3650, 2009) and Hasanuzzaman et al. (Energy 36:233, 2011). It will be significant to enhance fuel availability and decrease environmental pollution if the waste heat in the exhaust could be recovered. Thermoelectric generators (TEGs), which can translate heat into electricity, have become a topic of interest for vehicle exhaust waste heat recovery. In conventional automotive TEGs, the thermoelectric modules (TEMs) are arranged between the exhaust tank and the coolant tank. The TEMs do not contact the hot exhaust and coolant, which leads to low heat transfer efficiency. Moreover, to provide enough packing force to keep good contact with the exhaust tank and the coolant tank, the framework required is so robust that the TEGs become too heavy. Therefore, in current study, an automotive TEG was designed which included one exhaust channel, one coolant channel and several TEMs. In the TEG, the TEMs which contacted the exhaust and coolant directly were inserted into the walls of each coolant channel. To evaluate the performance of the automotive TEG, the flow field and temperature field were computed by computational fluid dynamics (CFD). Based on the temperature distribution obtained by CFD and the performance parameters of the modules, the total power generation was obtained by some proved empirical formulas. Compared with conventional automotive TEGs, the power generation per unit volume exhaust was boosted.

  16. An Evaluation of 3D Woven Orthogonal Composites' Potential in the Automotive Supply Chain

    Science.gov (United States)

    Taylor, Dalia

    The automotive supply chain and its management can be a very complex process and comprises a long dynamic and complex network that consists of four primary segments: original equipment manufacturers (OEMs), first tier suppliers, sub tiers suppliers, and infrastructure suppliers. During the analysis of the current automotive industry it was identified that textile industry importance is considerable increasing as a part of the global automotive supply chain, because textile products are used for interior, exterior and even suspension parts and components. Automotive industry has an increasing demand for higher quality exterior panels with better functional properties and reduced weight. One of the main potentials for this demand is based on the three-dimensional woven composites technology innovations which can replace an existing technology. The new role of the textile industry could make important changes in the automotive supply chain industry, such as: changes in the size of the supply chain, the time to the market and the position of textile industry in the automotive supply chain structure. 3D composite materials from high performance fibers, such as glass and carbon, have been used for automotive applications in a limited way due to the low production rate and the lack of research and development. This research will contribute to the understanding of textile composites in transportation and the textile parameters that affect the performance characteristics of these materials. The research examines the performance characteristics of lighter and stronger 3D woven fabric composites made from fiberglass with the aim to improve fuel efficiency by reducing the total vehicle weight while maintaining safety standards. The performance characteristics of the 3D woven fabric composite can be designed by changing different construction parameters, such as picks density, pick roving linear density, arrangements of warp and z-yarns, and the number of warp and picks layers

  17. Multiroller traction drive speed reducer: Evaluation for automotive gas turbine engine

    Science.gov (United States)

    Rohn, D. A.; Anderson, N. E.; Loewenthal, S. H.

    1982-01-01

    Tests were conducted on a nominal 14:1 fixed-ratio Nasvytis multiroller traction drive retrofitted as the speed reducer in an automotive gas turbine engine. Power turbine speeds of 45,000 rpm and a drive output power of 102 kW (137 hp) were reached. The drive operated under both variable roller loading (proportional to torque) and fixed roller loading (automatic loading mechanism locked). The drive operated smoothly and efficiently as the engine speed reducer. Engine specific fuel consumption with the traction speed reducer was comparable to that with the original helical gearset.

  18. Fuel flexible fuel injector

    Science.gov (United States)

    Tuthill, Richard S; Davis, Dustin W; Dai, Zhongtao

    2015-02-03

    A disclosed fuel injector provides mixing of fuel with airflow by surrounding a swirled fuel flow with first and second swirled airflows that ensures mixing prior to or upon entering the combustion chamber. Fuel tubes produce a central fuel flow along with a central airflow through a plurality of openings to generate the high velocity fuel/air mixture along the axis of the fuel injector in addition to the swirled fuel/air mixture.

  19. Efficient production of automotive biofuels; Effektiv produktion av biodrivmedel

    Energy Technology Data Exchange (ETDEWEB)

    Gode, Jenny; Hagberg, Linus; Rydberg, Tomas; Raadberg, Henrik; Saernholm, Erik

    2008-07-01

    The report describes opportunities and consequences associated with biomass polygeneration plants, in particular the role that heat plants (HP) or combined heat and power plants (CHP) in district heating systems can play in the production of automotive biofuels. The aim of the report is to provide a knowledge base to stakeholders to help assess energy and environmental benefits associated with collaborative approaches in planning, constructing and operating energy plants. Several configurations are possible for an energy polygeneration plant, but this report focuses on configurations in which a plant for automotive biofuel production and a district heating system with HPs or CHPs have been integrated in some way in order to achieve added value. The modes of integration are several, e.g.: - Supply of process steam from the CHP to the fuel plant, by which the time of operation for the CHP can be extended; Supply of surplus heat from the fuel plant to the district heating system; Material exchange between the systems, by use of residue streams from the fuel plant as fuel in the HP/CHP; Surplus heat from the fuel plant used for drying of the solid fuel to the HP/CHP or for drying of raw material for pellets production; Co-location providing opportunities for shared infrastructure for raw material handling, service systems, utilities and/or logistics. The report principally addresses integration options of the first three types, but describes briefly also pellets production. The starting point for the analysis of integration options is the description of technologies of interest for the production of automotive biofuels. Commercially available technologies are of prime interest, but also a couple of technologies under development are included in this part of the study. In addition to outlining the process characteristics for these processes, surrounding conditions and system requirements are briefly outlined. The results are summarized in Table S1. Ethanol fermentation

  20. Environmental economics of lignin derived transport fuels

    OpenAIRE

    Obydenkova, SV; Kouris, P Panagiotis; Hensen, EJM Emiel; Heeres, Hero J; Boot, MD Michael

    2017-01-01

    This paper explores the environmental and economic aspects of fast pyrolytic conversion of lignin, obtained from 2G ethanol plants, to transport fuels for both the marine and automotive markets. Various scenarios are explored, pertaining to aggregation of lignin from several sites, alternative energy carries to replace lignin, transport modalities, and allocation methodology. The results highlight two critical factors that ultimately determine the economic and/or environmental fuel viability....

  1. FUEL PROCESSING FOR FUEL CELLS: EFFECTS ON CATALYST DURABILITY AND CARBON FORMATION

    Energy Technology Data Exchange (ETDEWEB)

    R. BORUP; M. INBODY; B. MORTON; L. BROWN

    2001-05-01

    On-board production of hydrogen for fuel cells for automotive applications is a challenging developmental task. The fuel processor must show long term durability and under challenging conditions. Fuel processor catalysts in automotive fuel processors will be exposed to large thermal variations, vibrations, exposure to uncontrolled ambient conditions, and various impurities from ambient air and from fuel. For the commercialization of fuel processors, the delineation of effects on catalyst activity and durability are required. We are studying fuels and fuel constituent effects on the fuel processor system as part of the DOE Fuel Cells for Transportation program. Pure fuel components are tested to delineate the fuel component effect on the fuel processor and fuel processor catalysts. Component blends are used to simulate ''real fuels'', with various fuel mixtures being examined such as reformulated gasoline and naptha. The aliphatic, napthenic, olefin and aromatic content are simulated to represent the chemical kinetics of possible detrimental reactions, such as carbon formation, during fuel testing. Testing has examined the fuel processing performance of different fuel components to help elucidate the fuel constituent effects on fuel processing performance and upon catalyst durability. Testing has been conducted with vapor fuels, including natural gas and pure methane. The testing of pure methane and comparable testing with natural gas (97% methane) have shown some measurable differences in performance in the fuel processor. Major gasoline fuel constituents, such as aliphatic compounds, napthanes, and aromatics have been compared for their effect on the fuel processing performance. Experiments have been conducted using high-purity compounds to observe the fuel processing properties of the individual components and to document individual fuel component performance. The relative carbon formation of different fuel constituents have been measured by

  2. Hydrogen: the great debate. 'Power to Gas - how to cope with the challenge of electricity storage?; Hydrogen in energy transition: which challenges to be faced?; Hydrogen, essential today, indispensable tomorrow; Electrolytic hydrogen, a solution for energy transition?; Development of high power electrolysis systems: need and approach; Hydrogen as energy vector, Potential and stakes: a perspective; The Toyota Fuel Cell System: a new era for the automotive industry; Three key factors: production, applications to mobility, and public acceptance; Hydrogen, benevolent fairy or tempting demon

    International Nuclear Information System (INIS)

    Hauet, Jean-Pierre; Boucly, Philippe; Beeker, Etienne; Mauberger, Pascal; Quint, Aliette; Pierre, Helene; Lucchese, Paul; Bouillon-Delporte, Valerie; Chauvet, Bertrand; Brisse, Annabelle; Gautier, Ludmila; Hercberg, Sylvain; De Volder, Marc; Gruson, Jean-Francois; Marion, Pierre; Grellier, Sebastien; Devezeaux, Jean-Guy; Mansilla, Christine; Le Net, Elisabeth; Le Duigou, Alain; Maire, Jacques

    2015-01-01

    This publication proposes a set of contributions which address various issues related to the development of the use of hydrogen as an energy source. More precisely, these contributions discuss how to face the challenge of electricity storage by using the Power-to-Gas technology, the challenges to be faced regarding the role of hydrogen in energy transition, the essential current role of hydrogen and its indispensable role for tomorrow, the possible role of electrolytic hydrogen as a solution for energy transition, the need of and the approach to a development of high power electrolysis systems, the potential and stakes of hydrogen as an energy vector, the Toyota fuel cell system as a sign for new era for automotive industry, the three main factors (production, applications to mobility, and public acceptance) for the use of hydrogen in energy transition, and the role of hydrogen perceived either as a benevolent fairy or a tempting demon

  3. Balanced pressure gerotor fuel pump

    Energy Technology Data Exchange (ETDEWEB)

    Raney, Michael Raymond; Maier, Eugen

    2004-08-03

    A gerotor pump for pressurizing gasoline fuel is capable of developing pressures up to 2.0 MPa with good mechanical and volumetric efficiency and satisfying the durability requirements for an automotive fuel pump. The pump has been designed with optimized clearances and by including features that promote the formation of lubricating films of pressurized fuel. Features of the improved pump include the use of a shadow port in the side plate opposite the outlet port to promote balancing of high fuel pressures on the opposite sides of the rotors. Inner and outer rotors have predetermined side clearances with the clearances of the outer rotor being greater than those of the inner rotor in order to promote fuel pressure balance on the sides of the outer rotor. Support of the inner rotor and a drive shaft on a single bushing with bearing sleeves maintains concentricity. Additional features are disclosed.

  4. Automotive Body Trim and Glass; Automotive Mechanics 2: 9045.05.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    This document presents an outline for a 135-hour course designed to help students become employable with skills, knowledge, attitudes, and values necessary for performing the required service of the automotive trim and glass mechanic. The course of study includes an orientation to the course, service tools and bench skills development, and a study…

  5. Mountain Plains Learning Experience Guide: Automotive Repair. Course: Automotive Shop Safety.

    Science.gov (United States)

    Osland, Walt

    One of twelve individualized courses included in an automotive repair curriculum, this course presents avoidance of dangerous situations and accidents, and emergency equipment and procedures. The course is comprised of one unit, Shop Safety. The unit begins with a Unit Learning Experience Guide that gives directions for unit completion. The…

  6. Managing knowledge boundaries for open innovation - lessons from the automotive industry : lessons from the automotive industry

    NARCIS (Netherlands)

    Wilhelm, Miriam; Dolfsma, Wilfred

    2018-01-01

    Purpose - The rising need to innovate and obtain knowledge from more distant knowledge sources calls for new innovation strategies and a better integration of other external actors who lie outside the traditional automotive supply chain. Such an open innovation strategy challenges organizational

  7. Simulation of Assembly Line Balancing in Automotive Component Manufacturing

    Science.gov (United States)

    Jamil, Muthanna; Mohd Razali, Noraini

    2016-02-01

    This study focuses on the simulation of assembly line balancing in an automotive component in a vendor manufacturing company. A mixed-model assembly line of charcoal canister product that is used in an engine system as fuel's vapour filter was observed and found that the current production rate of the line does not achieve customer demand even though the company practices buffer stock for two days in advance. This study was carried out by performing detailed process flow and time studies along the line. To set up a model of the line by simulation, real data was taken from a factory floor and tested for distribution fit. The data gathered was then transformed into a simulation model. After verification of the model by comparing it with the actual system, it was found that the current line efficiency is not at its optimum condition due to blockage and idle time. Various what-if analysis were applied to eliminate the cause. Proposed layout shows that the line is balanced by adding buffer to avoid the blockage. Whereas, manpower is added the stations to reduce process time therefore reducing idling time. The simulation study was carried out using ProModel software.

  8. Catalytic gasification of automotive shredder residues with hydrogen generation

    Science.gov (United States)

    Lin, Kuen-Song; Chowdhury, Sujan; Wang, Ze-Ping

    Hydrogen is a clean and new energy carrier to generate power through the Proton exchange membrane fuel cell (PEMFC) system. Hydrogen can be effectively turned out through the catalytic gasification of organic material such as automotive shredder residues (ASR). The main objective of this manuscript is to present an analysis of the catalytic gasification of ASR for the generation of high-purity hydrogen in a lab-scale fixed-bed downdraft gasifier using 15 wt.% NiO/Al 2O 3 catalysts at 760-900 K. In the catalytic gasification process, reduction of Ni(II) catalyst into Ni(0) has been confirmed through XANES spectra and consequently EXAFS data shows that the central Ni atoms have Ni-O and Ni-Ni bonds with bond distances of 2.03 ± 0.05 and 2.46 ± 0.05 Å, respectively. ASR is partially oxidized and ultimately converts into hydrogen rich syngas (CO and H 2) and increases of the reaction temperature are favored the generation of hydrogen with decomposition of the CO. As well, approximately 220 kg h -1 of ASR would be catalytically gasified at 760-900 K and 46.2 atm with the reactor volume 0.27 m 3 to obtain approximately 3.42 × 10 5 kcal h -1 of thermal energy during over 87% syngas generation with the generation of 100 kW electric powers.

  9. A volumetric flow sensor for automotive injection systems

    Science.gov (United States)

    Schmid, U.; Krötz, G.; Schmitt-Landsiedel, D.

    2008-04-01

    For further optimization of the automotive power train of diesel engines, advanced combustion processes require a highly flexible injection system, provided e.g. by the common rail (CR) injection technique. In the past, the feasibility to implement injection nozzle volumetric flow sensors based on the thermo-resistive measurement principle has been demonstrated up to injection pressures of 135 MPa (1350 bar). To evaluate the transient behaviour of the system-integrated flow sensors as well as an injection amount indicator used as a reference method, hydraulic simulations on the system level are performed for a CR injection system. Experimentally determined injection timings were found to be in good agreement with calculated values, especially for the novel sensing element which is directly implemented into the hydraulic system. For the first time pressure oscillations occurring after termination of the injection pulse, predicted theoretically, could be verified directly in the nozzle. In addition, the injected amount of fuel is monitored with the highest resolution ever reported in the literature.

  10. Green innovation adoption in automotive supply chain

    DEFF Research Database (Denmark)

    Zailani, Suhaiza; Govindan, Kannan; Iranmanesh, Mohammad

    2015-01-01

    generators of industrial waste that affect the quality of the natural environment. This study aims to investigate the determinants of green innovation adoption and its effect on firm performance. Data were gathered by surveying 153 firms in the Malaysian automotive supply chain industry. Data were analyzed...... using the partial least squares technique. Environmental regulations, market demand, and firm internal initiatives have a positive effect on green innovation initiatives (GII), while GIIs have a positive effect on the three categories of sustainable performance (i.e., environmental, social, and economic...

  11. Dynamic characteristics of automotive steel sheets

    Directory of Open Access Journals (Sweden)

    M. Mihaliková

    2016-10-01

    Full Text Available The aim of this experimental research was to perform an analysis of deformation characteristics on two different types of steel: IF steel, and micro-alloyed steel were used automotive industry. For that purpose changes of properties of these materials were carried out by static 10-3 · s-1 and dynamic 103 · s-1 strain rate assess its plastic properties. Vickers micro hardness test was carried out by the static and dynamic loading condition and describes different hardness distribution. The higher strain hardening of materials was obtained too that was confirmed by distribution of dislocations.

  12. Building best practice automotive after sales network : The Volkswagen case

    NARCIS (Netherlands)

    Mikolik, Gerlinde

    2017-01-01

    This thesis aims to analyze the service operations and networks in the automotive industry as research into the automotive After Sales service network lacks the necessary fine details and industrial feedback. Its purpose is to present the insights and lessons learned from studying the After Sales

  13. Tune Up: Automotive Mechanics Instructional Program. Block 5.

    Science.gov (United States)

    O'Brien, Ralph D.

    The fifth of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in automotive tune-ups at the secondary and post secondary level. The material, as organized, is a suggested sequence of instruction within each block. Each lesson…

  14. Cooling System: Automotive Mechanics Instructional Program. Block 6.

    Science.gov (United States)

    O'Brien, Ralph D.

    The last of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in the automotive cooling system at the secondary and post secondary level. The material, as organized, is a suggested sequence of instruction within each block. Each…

  15. Radial basis function neural network in fault detection of automotive ...

    African Journals Online (AJOL)

    Radial basis function neural network in fault detection of automotive engines. ... Five faults have been simulated on the MVEM, including three sensor faults, one component fault and one actuator fault. The three sensor faults ... Keywords: Automotive engine, independent RBFNN model, RBF neural network, fault detection

  16. Potential energy consumption reduction of automotive climate control systems

    International Nuclear Information System (INIS)

    Nielsen, Filip; Uddheim, Åsa; Dalenbäck, Jan-Olof

    2016-01-01

    Highlights: • Twenty-on energy saving measures for vehicle interior climate were evaluated. • Few single energy saving measures could reduce the energy use significantly. • The operation of the system in intermediate conditions determines the energy use. • Required heating/cooling of passenger compartment had small effect on energy use. - Abstract: In recent years fuel consumption of passenger vehicles has received increased attention by customers, the automotive industry, regulatory agencies and academia. One area which affect the fuel consumption is climate control systems. Twenty-one energy saving measures were evaluated regarding the total energy use for vehicle interior climate using simulation. Evaluated properties were heat flow into the passenger compartment, electrical and mechanical work. The simulation model included sub models of the passenger compartment, air-handling unit, Air Conditioning (AC) system, engine and engine cooling system. A real-world representative test cycle, which included tests in cold, intermediate and warm conditions, was used for evaluation. In general, few single energy saving measures could reduce the energy use significantly. The measures with most potential were increased blower efficiency with a reduction of 46% of the electrical work and increased AC-system disengage temperature with a reduction of 27% of the mechanical work. These results show that the operation of the climate control system had a large effect on the energy use, especially compared to the required heating and cooling of the passenger compartment. As a result energy saving measures need to address how heating and cooling is generated before reducing the heat flow into the passenger compartment.

  17. Potentials and limitations of alternative fuels for diesel engine

    OpenAIRE

    Gligorijević Radinko; Jevtić Jeremija; Borak Đuro; Petrović Velimir

    2009-01-01

    The primary energy consumption in the world has increased continuously. The most important primary energy source is oil. The supply of automotive fuels today is based almost entirely on oil, and the demand for liquid transportation fuels worldwide will rise significantly in the next fifty years. Growing energy consumption and decreasing fossil resources are reasons for increasing prices of fossil fuel. Besides limited availability, contribution to greenhouse effect and pollutant emission repr...

  18. Survey of CFD studies on automotive buffeting

    International Nuclear Information System (INIS)

    An, C.-F.

    2005-01-01

    In the current automobile market buffeting is one of the customer frequent complaints on luxury cars and SUVs. Buffeting is a low frequency but high level wind noise and makes people inside the vehicle uncomfortable if it lasts for a long period of time. The physical mechanism of buffeting is a complicated phenomenon of aeroacoustic resonance. The aeroacoustic characteristics of buffeting depend on vehicle features and operating conditions. In this paper, a survey of CFD studies on the automotive buffeting is presented. Firstly, several buffeting related concepts, such as Helmholtz resonator, flow over a cavity, shear layer instability and vortex shedding, are reviewed and relevant references are listed. Then, a historic survey of the buffeting investigation is made with emphasis on computational studies. As an example, the buffeting studies at DaimlerChrysler are selected to demonstrate the procedure of CFD simulation for automotive buffeting. The procedure is then validated by the correlation with wind tunnel testing. After that the validated procedure is applied to find solutions for buffeting reduction. Finally, some comments on buffeting studies are addressed. (author)

  19. Novel Electronic Ballast for Automotive HID Lamps

    Science.gov (United States)

    Urakabe, Takahiro; Kinoshita, Hidehiko; Kawasaka, Taihei

    Simplifying the composition of the automotive HID lamp electronic ballast has been considered. This paper describes the novel electronic ballast that is composed of a DC/DC converter, a capacitor connected to a lamp in series, a switch (S3) connected to the capacitor in parallel, a switch (S2) placed between the output terminals of the DC/DC converter and also connected in parallel to the lamp and the capacitor in series, and an igniter. All MOSFETs (S1 in the DC/DC converter, S2 and S3) in the ballast are operated on the common voltage position (GND) of the circuit. The DC/DC converter is operated intermittently and the operation of S2 synchronizes with the operation of it to supply the lamp with an alternate square wave voltage. Operating an automotive HID lamp succeeded using the novel ballast and by setting some issues below. 1) The occurrence of the power loss when S2 is turned on. 2) The occurrence of extinction of gas discharge. This paper describes how the loss can be decreased if a part of the energy stored in the output capacitor of the DC/DC conveter is used to operate the lamp before S2 is turned on. It also describes how an inductor and a capacitor were added to the proposed electronic ballast to raise the lamp voltage in order to prevent the current from disappearing.

  20. The effect of oxygen storage capacity on the dynamic characteristics of an automotive catalytic converter

    International Nuclear Information System (INIS)

    Shamim, Tariq

    2008-01-01

    Automotive catalytic converters, which are employed to reduce engine exhaust emissions, are subjected to highly transient conditions during a typical driving cycle. These transient conditions arise from changes in driving mode, the hysteresis and flow lags of the feedback control system, and result in fluctuations of air-fuel ratio, exhaust gas flow rates and temperatures. The catalyst performance is also strongly influenced by the oxygen storage capacity. This paper presents a computational investigation of the effect of oxygen storage capacity on the dynamic behavior of an automotive catalytic converter subjected to modulations in exhaust gases. The modulations are generated by forcing the temporal variations in exhaust gases air-fuel ratio, gas flow rates and temperatures. The study employs a single-channel based, one-dimensional, non-adiabatic model. The results show that the imposed modulations cause a significant departure in the catalyst behavior from its steady behavior, and the oxygen storage capacity plays an important role in determining the catalyst's response to the imposed modulations. Modulations and oxygen storage capacity are found to have relatively greater influence on the catalyst's performance near stoichiometric conditions

  1. The potential of natural fibres for automotive sector - review

    Science.gov (United States)

    Fogorasi, MS; Barbu, I.

    2017-10-01

    Due to environment and sustainability regulation in the last decades considerable performance in green technology in the field of materials science through the development of biocomposites could be noticed. Thus, the development of high-performance materials produced from natural resources expands worldwide. This can be attributed mainly due to their assets compared to their synthetic contourparts like low cost, low weight, less damage to processing equipment, improved surface finish of moulded parts composite, good mechanical properties, biodegradability, abundant and renewable resources. Natural fibres are valuable and versatile resources with multiple advantages. Nowadays all the more, the automotive industry is under increasing pressure to fulfill environmental and performance demands and higher fuel efficiency at competitive costs. Automakers recognize potential in biocomposites if these materials can offer the same performance as traditional composites but with lower weight. Additional they exhibit non-brittle fracture on impact, which is another significant requirement for automotive sector. Other drivers that scores for use of natural fibres reinforced polymer composites (NFRPC) in automotive applications imply reduced waste disposal, reduction of greenhouse gas emission and Life Cycle Consideration. In spite of their benefits, the significant challenge for producers and supplier to handle with natural fiber reinforced polymer composites resides in large inconsistency of their properties. The chemical composition of vegetal fibres relies on several factors comprising fiber variety, time of harvesting, climatic history, soil characteristics and fibre processing technology. All these factors exert an influence on their final properties when used as reinforcements in biocomposite materials. In this review a wide range of issues is addressed with special reference to mechanical properties of fibres, interface adhesion and environmental implication of NFRPC. The

  2. Nanotechnology in automotive industry: research strategy and trends for the future-small objects, big impacts.

    Science.gov (United States)

    Coelho, Margarida C; Torrão, Guilhermina; Emami, Nazanin; Grácio, José

    2012-08-01

    The goal of this paper is to emphasize and present briefly the nanotechnology science and its potential impact on the automotive industry in order to improve the production of recent models with an optimization of the safety performance and a reduction in the environmental impacts. Nanomaterials can be applied in car bodies as light weight constructions without compromising the stiffness and crashwortiness, which means less material and less fuel consumption. This paper outlines the progress of nanotechnology applications into the safety features of more recent vehicle models and fuel efficiency, but also emphasis the importance of sustainable development on the application of these technologies and life cycle analysis of the considered materials, in order to meet the society trends and customers demands to improve ecology, safety and comfort.

  3. Minimizing of the boundary friction coefficient in automotive engines using Al2O3 and TiO2 nanoparticles

    International Nuclear Information System (INIS)

    Ali, Mohamed Kamal Ahmed; Xianjun, Hou; Elagouz, Ahmed; Essa, F.A.; Abdelkareem, Mohamed A. A.

    2016-01-01

    Minimizing of the boundary friction coefficient is critical for engine efficiency improvement. It is known that the tribological behavior has a major role in controlling the performance of automotive engines in terms of the fuel consumption. The purpose of this research is an experimental study to minimize the boundary friction coefficient via nano-lubricant additives. The tribological characteristics of Al 2 O 3 and TiO 2 nano-lubricants were evaluated under reciprocating test conditions to simulate a piston ring/cylinder liner interface in automotive engines. The nanoparticles were suspended in a commercially available lubricant in a concentration of 0.25 wt.% to formulate the nano-lubricants. The Al 2 O 3 and TiO 2 nanoparticles had sizes of 8–12 and 10 nm, respectively. The experimental results have shown that the boundary friction coefficient reduced by 35–51% near the top and bottom dead center of the stroke (TDC and BDC) for the Al 2 O 3 and TiO 2 nano-lubricants, respectively. The anti-wear mechanism was generated via the formation of protective films on the worn surfaces of the ring and liner. These results will be a promising approach for improving fuel economy in automotive.

  4. Automotive Mechanics Curriculum Outline for Secondary Schools. Vocational Education Curriculum Guide.

    Science.gov (United States)

    Louisiana State Dept. of Education, Baton Rouge. Div. of Vocational Education.

    This curriculum outline for secondary automotive mechanics is structured around Louisiana's Vocational-Technical Automotive Mechanics Curriculum. The curriculum is composed of 16 units of instruction, covering the following topics: benchwork, fundamentals of automotive engines, preventive maintenance, automotive brakes, steering and front…

  5. Bosch automotive electrics and automotive electronics systems and components, networking and hybrid drive

    CERN Document Server

    2014-01-01

    The significance of electrical and electronic systems has increased considerably in the last few years and this trend is set to continue. The characteristics feature of innovative systems is the fact that they can work together in a network. This requires powerful bus systems that the electronic control units can use to exchange information. Networking and the various bus systems used in motor vehicles are the prominent new topic in the 5th edition of the "Automotive Electric, Automotive Electronics" technical manual. The existing chapters have also been updated, so that this new edition brings the reader up to date on the subjects of electrical and electronic systems in the motor vehicle. Content Electrical and electronical systems – Basic principles of networking - Examples of networked vehicles – Bus systems – Architecture of electronic systems – Mechatronics – Elektronics – Electronic control Units – Software – Sensors – Actuators – Hybrid drives – Vehicle electrical system – Start...

  6. Advances in LEDs for automotive applications

    Science.gov (United States)

    Bhardwaj, Jy; Peddada, Rao; Spinger, Benno

    2016-03-01

    High power LEDs were introduced in automotive headlights in 2006-2007, for example as full LED headlights in the Audi R8 or low beam in Lexus. Since then, LED headlighting has become established in premium and volume automotive segments and beginning to enable new compact form factors such as distributed low beam and new functions such as adaptive driving beam. New generations of highly versatile high power LEDs are emerging to meet these application needs. In this paper, we will detail ongoing advances in LED technology that enable revolutionary styling, performance and adaptive control in automotive headlights. As the standards which govern the necessary lumens on the road are well established, increasing luminance enables not only more design freedom but also headlight cost reduction with space and weight saving through more compact optics. Adaptive headlighting is based on LED pixelation and requires high contrast, high luminance, smaller LEDs with high-packing density for pixelated Matrix Lighting sources. Matrix applications require an extremely tight tolerance on not only the X, Y placement accuracy, but also on the Z height of the LEDs given the precision optics used to image the LEDs onto the road. A new generation of chip scale packaged (CSP) LEDs based on Wafer Level Packaging (WLP) have been developed to meet these needs, offering a form factor less than 20% increase over the LED emitter surface footprint. These miniature LEDs are surface mount devices compatible with automated tools for L2 board direct attach (without the need for an interposer or L1 substrate), meeting the high position accuracy as well as the optical and thermal performance. To illustrate the versatility of the CSP LEDs, we will show the results of, firstly, a reflector-based distributed low beam using multiple individual cavities each with only 20mm height and secondly 3x4 to 3x28 Matrix arrays for adaptive full beam. Also a few key trends in rear lighting and impact on LED light

  7. Dual-fuelling of a direct-injection automotive diesel engine by diesel and compressed natural gas

    International Nuclear Information System (INIS)

    Pirouzpanah, V.; Mohammadi Kosha, A.; Mosseibi, A.; Moshirabadi, J.; Gangi, A.; Moghadaspour, M.

    2000-01-01

    Application of Compressed Natural Gas in diesel engines has always been important, especially in the field of automotive engineering. This is due to easy accessibility, better mixing quality and good combustion characteristics of the Compressed Natural Gas fuel. In this study the application of Compressed Natural Gas fuel along with diesel oil in a heavy duty direct-injection automotive diesel engine is experimentally investigated. In order to convert a diesel engine into a diesel-gas one, the so called m ixed diesel-gas a pproach has been used and for this purpose a carbureted Compressed Natural Gas fuel system has been designed and manufactured. For controlling quantity of Compressed Natural Gas, the gas valve is linked to the diesel fuel injection system by means of a set of rods. Then, the dual-fuel system is adjusted so that, at full load conditions, the quantity of diesel fuel is reduced to 20% and 80% of its equivalent energy is substituted by Compressed Natural Gas fuel. Also injection pressure of pilot jet is increased by 11.4%. Performance and emission tests are conducted under variation of load and speed on both diesel and diesel-gas engines. Results show that, with equal power and torque, the diesel-gas engine has the potential to improve overall engine performance and emission. For example, at rated power and speed, fuel economy increases by 5.48%, the amount of smoke decreases by 78%, amount of CO decreases by 64.3% and mean exhaust gas temperature decreases by 6.4%

  8. Cradle-to-Gate Impact Assessment of a High-Pressure Die-Casting Safety-Relevant Automotive Component

    Science.gov (United States)

    Cecchel, Silvia; Cornacchia, Giovanna; Panvini, Andrea

    2016-09-01

    The mass of automotive components has a direct influence on several aspects of vehicle performance, including both fuel consumption and tailpipe emissions, but the real environmental benefit has to be evaluated considering the entire life of the products with a proper life cycle assessment. In this context, the present paper analyzes the environmental burden connected to the production of a safety-relevant aluminum high-pressure die-casting component for commercial vehicles (a suspension cross-beam) considering all the phases connected to its manufacture. The focus on aluminum high-pressure die casting reflects the current trend of the industry and its high energy consumption. This work shows a new method that deeply analyzes every single step of the component's production through the implementation of a wide database of primary data collected thanks to collaborations of some automotive supplier companies. This energy analysis shows significant environmental benefits of aluminum recycling.

  9. Fuel economy and range estimates for fuel cell powered automobiles

    Energy Technology Data Exchange (ETDEWEB)

    Steinbugler, M.; Ogden, J. [Princeton Univ., NJ (United States)

    1996-12-31

    While a number of automotive fuel cell applications have been demonstrated, including a golf cart, buses, and a van, these systems and others that have been proposed have utilized differing configurations ranging from direct hydrogen fuel cell-only power plants to fuel cell/battery hybrids operating on reformed methanol. To date there is no clear consensus on which configuration, from among the possible combinations of fuel cell, peaking device, and fuel type, is the most likely to be successfully commercialized. System simplicity favors direct hydrogen fuel cell vehicles, but infrastructure is lacking. Infrastructure favors a system using a liquid fuel with a fuel processor, but system integration and performance issues remain. A number of studies have analyzed particular configurations on either a system or vehicle scale. The objective of this work is to estimate, within a consistent framework, fuel economies and ranges for a variety of configurations using flexible models with the goal of identifying the most promising configurations and the most important areas for further research and development.

  10. Checklist for transition to new highway fuel(s).

    Energy Technology Data Exchange (ETDEWEB)

    Risch, C.; Santini, D.J. (Energy Systems)

    2011-12-15

    Transportation is vital to the U.S. economy and society. As such, U.S. Presidents have repeatedly stated that the nation needs to reduce dependence on petroleum, especially for the highway transportation sector. Throughout history, highway transportation fuel transitions have been completed successfully both in United States and abroad. Other attempts have failed, as described in Appendix A: Historical Highway Fuel Transitions. Planning for a transition is critical because the changes can affect our nation's ability to compete in the world market. A transition will take many years to complete. While it is tempting to make quick decisions about the new fuel(s) of choice, it is preferable and necessary to analyze all the pertinent criteria to ensure that correct decisions are made. Doing so will reduce the number of changes in highway fuel(s). Obviously, changes may become necessary because of occurrences such as significant technology breakthroughs or major world events. With any and all of the possible transitions to new fuel(s), the total replacement of gasoline and diesel fuels is not expected. These conventional fuels are envisioned to coexist with the new fuel(s) for decades, while the revised fuel and vehicle infrastructures are implemented. The transition process must analyze the needs of the primary 'players,' which consist of the customers, the government, the fuel industry, and the automotive industry. To maximize the probability of future successes, the prime considerations of these groups must be addressed. Section 2 presents a succinct outline of the Checklist. Section 3 provides a brief discussion about the groupings on the Checklist.

  11. Fuel cells - from the laboratory to the road

    Energy Technology Data Exchange (ETDEWEB)

    Fronk, M.H. [Delphi Energy and Engine Management Systems, Rochester, NY (United States)

    1996-12-31

    The polymer electrolyte membrane (PEM) Fuel Cell faces stiff competition from existing automotive powerplants and other Hybrid APUs. To be successful, the Fuel Cell will have to demonstrate real customer advantages such as fuel economy and emissions. The PEM technology has an inherent advantage over other powerplants in both thermal efficiency and emission performance, and as such fits in very well with the future regulations that strive to clean up the environment. In addition, it will need to be cost competitive and provide acceptable performance. The majority of development activity on PEM Fuel Cells to date has concentrated primarily in the area of Stack refinement and optimization with improvements coming in higher power densities and higher specific power. To make the Fuel Cell compatible with an automotive environment the entire system will need to be analyzed, understood, and then engineered to work together in an efficient manner.

  12. Smart cover glass for automotive applications

    Science.gov (United States)

    Chung, Sang Kug

    2017-11-01

    This paper presents a smart cover glass based on electrowetting-on-dielectric (EWOD) actuation for automotive applications. It can remove water droplets in a wide range of sizes to allow the camera's lens to get clean at any time. The proposed cover glass offers a simple design structure to be easily installed on any device but provides a fast and energy efficient droplet cleaning operation. As proof of concept, a real imaging test is carried out using a mobile smartphone camera and landscape photography. When water droplets with different volumes are on the camera cover glass, the image of landscape photography is distorted with blurred spots. However, the distorted image is restored by removing the droplets through EWOD actuation.

  13. Spectroscopic analysis of automotive engine oil

    Science.gov (United States)

    Dahmani, Rachid; Gupta, Neelam

    2002-02-01

    Infrared absorption spectroscopy (IR) and acousto-optic tunable filter (AOTF) technology were combined to develop a portable spectrophotometer for use in engine oil analysis to identify and quantify oil contaminants and residue products, Preliminary measurements were taken with a field-portable AOTF-based spectrometer (2 to 4.5 micrometers ) and an FTIR spectrometer (2 to 25 micrometers ) for comparison. Absorption spectra of used and unused oil samples were measured and compared to determine absorption changes between the various samples resulting from oil degradation and any chemical reactions that might have taken place during high- temperature engine lubrication. These preliminary results indicate that IR spectroscopy can be used for oil quality monitoring in automotive engines, which will help predict and prevent engine failure and degradation. This work can be extended to other remote sensing applications, such as the monitoring of environmental oil spills.

  14. Active gated imaging for automotive safety applications

    Science.gov (United States)

    Grauer, Yoav; Sonn, Ezri

    2015-03-01

    The paper presents the Active Gated Imaging System (AGIS), in relation to the automotive field. AGIS is based on a fast gated-camera equipped with a unique Gated-CMOS sensor, and a pulsed Illuminator, synchronized in the time domain to record images of a certain range of interest which are then processed by computer vision real-time algorithms. In recent years we have learned the system parameters which are most beneficial to night-time driving in terms of; field of view, illumination profile, resolution and processing power. AGIS provides also day-time imaging with additional capabilities, which enhances computer vision safety applications. AGIS provides an excellent candidate for camera-based Advanced Driver Assistance Systems (ADAS) and the path for autonomous driving, in the future, based on its outstanding low/high light-level, harsh weather conditions capabilities and 3D potential growth capabilities.

  15. Multi-channel automotive night vision system

    Science.gov (United States)

    Lu, Gang; Wang, Li-jun; Zhang, Yi

    2013-09-01

    A four-channel automotive night vision system is designed and developed .It is consist of the four active near-infrared cameras and an Mulit-channel image processing display unit,cameras were placed in the automobile front, left, right and rear of the system .The system uses near-infrared laser light source,the laser light beam is collimated, the light source contains a thermoelectric cooler (TEC),It can be synchronized with the camera focusing, also has an automatic light intensity adjustment, and thus can ensure the image quality. The principle of composition of the system is description in detail,on this basis, beam collimation,the LD driving and LD temperature control of near-infrared laser light source,four-channel image processing display are discussed.The system can be used in driver assistance, car BLIS, car parking assist system and car alarm system in day and night.

  16. Determining organic pollutants in automotive industry sludge.

    Science.gov (United States)

    Munaretto, Juliana S; Wonghon, Audrey L; von Mühlen, Carin

    2012-12-01

    In Brazil, the policy for disposing industrial sludge is changing from an emphasis on using controlled landfills to other treatment or co-processing methods; however, the monitoring of organic pollutants is not mandatory. The present study evaluated two general screening methods for organic pollutants in sludge generated in an automotive industrial complex in southern Brazil. The screening was performed using Soxhlet and sonication extractions and Gas Chromatograph coupled with Quadrupole Mass Spectrometry (GC/qMS). It was concluded that both techniques were effective and that most of the compounds identified were alkanes, phenols and esters. Important pollutants were detected in the sludge, which confirms the necessity of monitoring this type of residue.

  17. CRM Implementation in the Automotive Industry

    OpenAIRE

    Öner, Dila; Xhemali, Lorena

    2009-01-01

    Date:                  2009-05-27 Level:                 Master Thesis in International Business and Entrepreneurship, 15 ECTS Institution:        School of Sustainable Development of Society and Technology, Mälardalen University   Title:                  The Implementation of Customer Relationship Management (CRM) in the Automotive Industry   Supervisor:       Peter Ekman Research           Exploiting the stages of CRM implementation and looking into the obstacles faced Issue:               ...

  18. Executable UML Modeling For Automotive Embedded Systems

    International Nuclear Information System (INIS)

    Gerard, Sebastien

    2000-01-01

    Engineers are more and more faced to the hard problem of sophisticated real-time System whereas time to market becomes always smaller. Object oriented modeling supported by UML standard brings effective solutions to such problems. However the possibility to specify real-time aspects of an application are not yet fully satisfactory Indeed, existing industrial proposals supply good answers to concurrency specification problem but they are yet limited regarding to real-time quantitative properties specification of an application. This work aims to construct a complete and consistent UML methodology based on a profile dedicated to automotive embedded Systems modeling and prototyping. This profile contains ail needed extensions to express easily the real-time quantitative properties of an application. Moreover, thanks to the formalization of UML protocol state machines, real-time concepts have been well-integrated in the object oriented paradigm. The main result of this deep integration is that a user is now able to model real-time Systems through the classical object oriented view i.e. without needing any specific knowing in real-time area. In order to answer to an industrial requirement, Systems prototyping (key point for car industry) the ACCORD/UML approach allows also to build executable models of an application. For that purpose, the method supplies a set of rules allow.ng to remove UML ambiguous semantics points, to complete semantics variation points and then to obtain a complete and coherent global model of an application being executable. The work of UML extension and its using formalization realized all along this thesis supplied also a complete and non-ambiguous modeling framework for automotive electronics Systems development. This is also a base particularly well-suited to tackle other facets of the Systems development as automatic and optimized code generation, validation, simulation or tests. (author) [fr

  19. Assessment of Safety Standards for Automotive Electronic Control Systems

    Science.gov (United States)

    2016-06-01

    This report summarizes the results of a study that assessed and compared six industry and government safety standards relevant to the safety and reliability of automotive electronic control systems. These standards include ISO 26262 (Road Vehicles - ...

  20. Sustainable supply chain management practices in Indian automotive industry

    DEFF Research Database (Denmark)

    Mathivathanan, Deepak; Kannan, Devika; Haq, A. Noorul

    2018-01-01

    for a competitive edge have forced the automotive industry to consider their environmental and social impacts in addition to their economic status. These pressures have led many automotive industry businesses to adopt Sustainable Supply Chain Management (SSCM) practices. Specific practices that are adopted......As one of the largest manufacturing sectors, the automotive industry has a deep impact on the society and environment. Automotive products provide mobility to millions and create jobs, but also threaten the environment. Consumer pressure, government regulations, and stakeholder demands...... into the traditional supply chain and that help an industry shift towards a sustainable supply chain are called SSCM practices. Firms have difficulty identifying the most useful practices and learning how these practices impact each other. Unfortunately, no existing research has studied the interrelated influences...

  1. Firm and Product Heterogeneity in China's Automotive Exports

    Directory of Open Access Journals (Sweden)

    Jing Wang

    2015-12-01

    Full Text Available The main purpose of this paper is to provide an in-depth analysis of the anatomy of China's automotive exports, relying on the literature on firm and product heterogeneity. For this purpose, we use highly disaggregated HS 8-digit product-category level data collected by the Chinese Customs Office for 2000 and 2008, and we distinguish between foreign firms, domestic public firms, and domestic private firms. We also decompose automotive products into autos and auto parts and components (P/C. We then calculate both the extensive margins – number of products exported – and intensive margins – average value of exports per product – of China's automotive exports. We estimate gravity equations to assess the determinants of China's exports of autos and auto P/C. Overall, our analysis yields a number of new, interesting stylized facts about China's automotive exports by confirming the need for taking into account different types of heterogeneity in analyzing international trade.

  2. SEE - Sight Effectiveness Enhancement. Results of the automotive evaluation

    DEFF Research Database (Denmark)

    Andersen, V.; Hansen, K.D.; Cathala, T.

    2006-01-01

    In the SEE project two parallel evaluations have been conducted, an experimental trial of the automotive and another of the aeronautical application. The evaluations have measured the efficiency and HMI (human-machine interaction) characteristics of theSEE prototype. This report covers the automo......In the SEE project two parallel evaluations have been conducted, an experimental trial of the automotive and another of the aeronautical application. The evaluations have measured the efficiency and HMI (human-machine interaction) characteristics of theSEE prototype. This report covers...... the automotive part of the evaluation. The evaluation of the automotive application was carried out in computer simulated environments and followed the general objectives of the evaluation described in ‘Definition of theEvaluation Plan’ . The field experiment discussed, however, was given up due to lack...

  3. Following Industry's Lead: Revising the Automotive Technology Curriculum

    Science.gov (United States)

    Crouse, William H.; Anglin, Donald L.

    1976-01-01

    Today's automotive technology curriculum is changing; curriculum revisions are being made in response to both the changing automobile and to the latest social trends and laws affecting students and teachers alike. (Author)

  4. Conference on Future Automotive Technology Focus Electro Mobility

    CERN Document Server

    2013-01-01

    The increasing trend towards electric cars leads to several challenges for the automobile industry, research institutes and politics as well as for the society. Research and serial development move closer together to meet automotive standards with new components such as traction batteries integrated into hybrid and electrical drivetrains. Furthermore, the influence of e-mobility on the daily mobility behavior, the effects on the automotive supply chain and the impact on industrial production have to be taken into account. According to these complex aspects it is crucial to not only acquire specific knowledge in the particular fields but also to consider their functional interaction. Therefore, it seems essential to merge competence from science, economy and politics. This year, the annual „Conference on Future Automotive Technology“ as the follow-up of the „2. Automobiltechnisches Kolloquium München” focuses on the economical realization of widespread automotive electro mobility. Contents - Energy St...

  5. METHOD OF HYDROGEN FEEDING FOR AUTOMOTIVE ENGINE SUPPLY

    Directory of Open Access Journals (Sweden)

    F. Abramchuk

    2010-01-01

    Full Text Available On basis of analysis of various methods of hydrogen feeding for automotive engine supply methods of multipoint hydrogen distribution with microprocessor-based control are proposed.

  6. THE AUTOMOTIVE INDUSTRY IN A NEW TEHNOLOGICAL ERA

    Directory of Open Access Journals (Sweden)

    Simona Catalina ALBULESCU

    2014-11-01

    Full Text Available The business world is changing at an impressive speed: the global financial crisis, challenging markets, technology and talent crisis have a major impact on business. The last century can be associated with the triumph of the automobile industry. At the beginning of the 21st century the automotive industry has experienced one of the largest shifts in the automotive history. The new CO2 regulations on global level have determined the automotove industry to adopt new and original technologies faster than anticipated. The emerging tendency of car sharing in larger cities added to the media information related to the negative environmental effects of car mobility generate concerns that customers were seeking a replacement to the traditional, individual car ownership. The automotive industry will face challenging years ahead taking into consideration the shifting paradigm in auto-mobility. In this context, this article aims to provide a general perspective of the tendencies in the automotive sector.

  7. Motor fuel demand analysis - applied modelling in the European union

    International Nuclear Information System (INIS)

    Chorazewiez, S.

    1998-01-01

    Motor fuel demand in Europe amounts to almost half of petroleum products consumption and to thirty percent of total final energy consumption. This study considers, Firstly, the energy policies of different European countries and the ways in which the consumption of motor gasoline and automotive gas oil has developed. Secondly it provides an abstract of demand models in the energy sector, illustrating their specific characteristics. Then it proposes an economic model of automotive fuel consumption, showing motor gasoline and automotive gas oil separately over a period of thirty years (1960-1993) for five main countries in the European Union. Finally, forecasts of consumption of gasoline and diesel up to the year 2020 are given for different scenarios. (author)

  8. The Indian Automotive Industry and the ASEAN Supply Chain Relations

    OpenAIRE

    Tristan Leo Dallo AGUSTIN; Martin SCHRODER

    2015-01-01

    The topic of automotive supply chains has been increasingly studied as it raises questions of economic development, especially from the perspectives of simultaneous globalisation and regionalisation, and trade. While ASEAN is a prime example of intraregional production networks, supply chains that connect ASEAN and India have not been studied indepth. Therefore, this paper investigates the Indian automotive industry, which is composed of automobile original equipment manufacturers (OEMs) and ...

  9. Competitive analysis by automotive repair shops, using customer perceived value

    OpenAIRE

    Baby Moreno, Jaime; Uribe Arango, Juan Fernando

    2015-01-01

    This paper addresses the use of customer perceived value (CPV) as a tool for competitive analysis among automotive repair and maintenance shops. It describes how to determine both the relative importance of properties taken into account by customers when assessing the performance of an automotive repair shop, and the performance assessment conducted by the users of repair shops owned by car dealers and by individuals. Subsequently, it illustrates how both types of repair shops view their comp...

  10. Economics of Direct Hydrogen Polymer Electrolyte Membrane Fuel Cell Systems

    Energy Technology Data Exchange (ETDEWEB)

    Mahadevan, Kathyayani

    2011-10-04

    Battelle's Economic Analysis of PEM Fuel Cell Systems project was initiated in 2003 to evaluate the technology and markets that are near-term and potentially could support the transition to fuel cells in automotive markets. The objective of Battelle?s project was to assist the DOE in developing fuel cell systems for pre-automotive applications by analyzing the technical, economic, and market drivers of direct hydrogen PEM fuel cell adoption. The project was executed over a 6-year period (2003 to 2010) and a variety of analyses were completed in that period. The analyses presented in the final report include: Commercialization scenarios for stationary generation through 2015 (2004); Stakeholder feedback on technology status and performance status of fuel cell systems (2004); Development of manufacturing costs of stationary PEM fuel cell systems for backup power markets (2004); Identification of near-term and mid-term markets for PEM fuel cells (2006); Development of the value proposition and market opportunity of PEM fuel cells in near-term markets by assessing the lifecycle cost of PEM fuel cells as compared to conventional alternatives used in the marketplace and modeling market penetration (2006); Development of the value proposition of PEM fuel cells in government markets (2007); Development of the value proposition and opportunity for large fuel cell system application at data centers and wastewater treatment plants (2008); Update of the manufacturing costs of PEM fuel cells for backup power applications (2009).

  11. Profiles of Major Suppliers to the Automotive Industry : Vol. 2. Iron, Steel and Aluminum Suppliers to the Automotive Industry

    Science.gov (United States)

    1982-08-01

    This study summarizes extensive information collected over a two-year period (October 1978 to October 1980) on suppliers of parts and components, materials, and machine tools to the automotive industry in the United States. The objective of the study...

  12. Profiles of Major Suppliers to the Automotive Industry : Vol. 7. Machine Tool Suppliers to the Automotive Industry.

    Science.gov (United States)

    1982-08-01

    This study summarizes extensive information collected over a two-year period (October 1978 to October 1980) on suppliers of parts and components, materials, and machine tools to the automotive industry in the United States. The objective of the study...

  13. Profiles of Major Suppliers to the Automotive Industry : Vol. 4. North American Automotive Parts and Components Suppliers

    Science.gov (United States)

    1982-08-01

    This study summarizes extensive information collected over a two-year period (October 1978 to October 1980) on suppliers of parts and components, materials, and machine tools to the automotive industry in the United States. The objective of the study...

  14. [Fuel substitution of vehicles by natural gas: Summaries of four final technical reports

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    This report contains summary information on three meetings and highlights of a fourth meeting held by the Society of Automotive Engineers on natural gas fueled vehicles. The meetings covered the following: Natural gas engine and vehicle technology; Safety aspects of alternately fueled vehicles; Catalysts and emission control--Meeting the legislative standards; and LNG--Strengthening the links.

  15. Optimization of the overall energy consumption in cascade fueling stations for hydrogen vehicles

    DEFF Research Database (Denmark)

    Rothuizen, Erasmus Damgaard; Rokni, Masoud

    2014-01-01

    Hydrogen fueling stations are emerging around and in larger cities in Europe and United States together with a number of hydrogen vehicles. The most stations comply with the refueling protocol made by society of automotive engineers and they use a cascade fueling system on-site for filling...

  16. The start-up analysis of a PEM fuel cell system in vehicles

    DEFF Research Database (Denmark)

    Rabbani, Raja Abid; Rokni, Masoud; Hosseinzadeh, Elham

    2014-01-01

    Addressing large load fluctuation in automotive applications, dynamic analysis of a polymer electrolyte membrane fuel cell system is conducted here. Operations of a comprehensive system-level control-oriented fuel cell model with all necessary auxiliary components are demonstrated and simulation...

  17. Technological aspects in synthesis and characterization of proton conducting polyetheretherketone (PEEK) membranes for fuel cell applications.

    CSIR Research Space (South Africa)

    Vaivars, G

    2009-08-01

    Full Text Available The research on ion-exchange membranes has grown considerably in recent years with the growing interest in fuel cell technology for the automotive and portable applications. The requirements for a fuel cell membrane are the following: high chemical...

  18. Fuel-mix and energy utilization analysis of Port Harcourt Refining Company, Nigeria

    OpenAIRE

    Badmus, Ismaila; Fagbenle, Richard; Oyewola, Olanrewaju

    2017-01-01

    This study analyses the fuel-mix and energy utilization patterns in Port Harcourt Refining Company from 2000 to 2011. The average fuel mix over the study period is 43% refinery fuel gas, 0% liquefied petroleum gas (LPG), 44% low pour fuel oil (LPFO), 8% Coke, and 5% automotive gas oil (AGO). The present ratio of high-carbon fuel consumption to low-carbon fuel consumption adversely influences the specific fuel consumption by increasing it. Our proposal is that the present AGO and LPFO consumpt...

  19. Carbon Fiber Composite Materials for Automotive Applications

    Energy Technology Data Exchange (ETDEWEB)

    Norris, Jr., Robert E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mainka, Hendrik [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-06-01

    Volkswagen (VW) is internationally recognized for quantity and quality of world-wide vehicle production and the Oak Ridge National Laboratory (ORNL) is internationally recognized in materials research and development. With automotive production ramping up in the recently constructed VW Group of America facility in Chattanooga, Tennessee, ORNL and VW initiated discussions in 2012 concerning opportunities for collaboration around ORNL’s carbon fiber and composites programs. ORNL is conducting an internationally recognized program to develop and implement lower cost carbon fibers and composites for automotive and other “energy missions” for the US Department of Energy. Significant effort is ongoing in selecting, developing, and evaluating alternative precursors, developing and demonstrating advanced conversion techniques, and developing and tailoring surface treatment, sizings, and formatting fiber for specific composite matrices and end-use applications. ORNL already had North America’s most comprehensive suite of tools for carbon fiber research and development and established a semiproduction demonstration line referred to as the Carbon Fiber Technology Facility (CFTF) to facilitate implementation of low cost carbon fiber (LCCF) approaches in early 2013. ORNL and VW agreed to collaborate in a formal Cooperative Research and Development Agreement (NFE-12-03992) specifically focused on evaluating applicability of low cost carbon fiber products for potential vehicle components. The goal of the work outlined in this report was to develop and qualify uses for carbon fiber-reinforced structures in connection with civilian ground transportation. Significant progress was achieved in evaluating and understanding lignin-based precursor materials; however, availability of carbon fiber converted from lignin precursor combined with logistical issues associated with the Visa limitations for the VW participant resulted in significantly shortening of the collaboration

  20. Application of Proton Exchange Membrane Fuel Cell for Lift Trucks

    DEFF Research Database (Denmark)

    Hosseinzadeh, Elham; Rokni, Masoud

    2011-01-01

    in order to account for water back diffusion. Further Membrane water content is assumed to be a linear function of thickness. PEM fuel cell is working at rather low operating conditions which makes it suitable for the automotive systems. In this paper motive power part of a lift truck has been investigated...

  1. Energizing Engineering Students with Hydrogen Fuel Cell Project

    Science.gov (United States)

    Cannell, Nori; Zavaleta, Dan

    2010-01-01

    At Desert Vista High School, near Phoenix, Arizona, Perkins Innovation Grant funding is being used to fund a program that is helping to prepare students for careers in engineering by giving them hands-on experience in areas like hydrogen generation and fuel cell utilization. As one enters Dan Zavaleta's automotive and engineering classroom and lab…

  2. Automotive Thermoelectric Generator impact on the efficiency of a drive system with a combustion engine

    Directory of Open Access Journals (Sweden)

    Ziolkowski Andrzej

    2017-01-01

    Full Text Available Increasing the combustion engine drive systems efficiency is currently being achieved by structural changes in internal combustion engines and its equipment, which are geared towards limiting mechanical, thermal and outlet losses. For this reason, downsizing. In addition to these changes, all manner of exhaust gas energy recovery systems are being investigated and implemented, including turbocompound, turbogenerators and thermoelectric generators. The article presents the author’s idea of a thermoelectric generator system of automotive applications ATEG (Automotive Thermoelectric Generator and the study of the recovery of exhaust gas energy stream. The ATEG consists of a heat exchanger, thermoelectric modules and a cooling system. In this solution, 24 commercial thermoelectric modules based on Bi2Te3 (bismuth telluride were used. Measurements were made at two engine test sites on which SI and CI engines were installed. The exhaust gas parameters (temperature and mass flow rate, fuel consumption and operating parameters of the ATEG – the intensity and the voltage generated by the thermoelectric modules and the temperature on the walls of the heat exchanger – were all measured in the experiments. Based on the obtained results, the exhaust gas energy flow and the power of the ATEG were determined as well as its effect on the diesel engine drive system efficiency.

  3. Building Block Approach' for Structural Analysis of Thermoplastic Composite Components for Automotive Applications

    Science.gov (United States)

    Carello, M.; Amirth, N.; Airale, A. G.; Monti, M.; Romeo, A.

    2017-12-01

    Advanced thermoplastic prepreg composite materials stand out with regard to their ability to allow complex designs with high specific strength and stiffness. This makes them an excellent choice for lightweight automotive components to reduce mass and increase fuel efficiency, while maintaining the functionality of traditional thermosetting prepreg (and mechanical characteristics) and with a production cycle time and recyclability suited to mass production manufacturing. Currently, the aerospace and automotive sectors struggle to carry out accurate Finite Elements (FE) component analyses and in some cases are unable to validate the obtained results. In this study, structural Finite Elements Analysis (FEA) has been done on a thermoplastic fiber reinforced component designed and manufactured through an integrated injection molding process, which consists in thermoforming the prepreg laminate and overmolding the other parts. This process is usually referred to as hybrid molding, and has the provision to reinforce the zones subjected to additional stresses with thermoformed themoplastic prepreg as required and overmolded with a shortfiber thermoplastic resin in single process. This paper aims to establish an accurate predictive model on a rational basis and an innovative methodology for the structural analysis of thermoplastic composite components by comparison with the experimental tests results.

  4. Future Automotive Aftertreatment Solutions: The 150°C Challenge Workshop Report

    Energy Technology Data Exchange (ETDEWEB)

    Zammit, Michael; DiMaggio, Craig L.; Kim, Chang H.; Lambert, Christine; Muntean, George G.; Peden, Charles HF; Parks, James E.; Howden, Ken

    2013-10-15

    With future fuel economy standards enacted, the U.S. automotive manufacturers (OEMs) are committed to pursuing a variety of high risk/highly efficient stoichiometric and lean combustion strategies to achieve superior performance. In recognition of this need, the U.S. Department of Energy (DOE) has partnered with domestic automotive manufacturers through U.S. DRIVE to develop these advanced technologies. However, before these advancements can be introduced into the U.S. market, they must also be able to meet increasingly stringent emissions requirements. A significant roadblock to this implementation is the inability of current catalyst and aftertreatment technologies to provide the required activity at the much lower exhaust temperatures that will accompany highly efficient combustion processes and powertrain strategies. Therefore, the goal of this workshop and report is to create a U.S. DRIVE emission control roadmap that will identify new materials and aftertreatment approaches that offer the potential for 90% conversion of emissions at low temperature (150°C) and are consistent with highly efficient combustion technologies currently under investigation within U.S. DRIVE Advanced Combustion and Emission Control (ACEC) programs.

  5. A study of the Armstrong Whitworth swing beam engine for automotive application

    Science.gov (United States)

    1983-01-01

    The introduction of ceramics to those parts suffering high thermal loading was successfully demonstrated, and there is no question that the 100 kw (134 hp) naturally aspirated engine of the future will be developed to produce up to 300 kw (402 hp) by the application of turbocharging or its equivalent. However, at the 60 - 80 kw (80 - 107 hp) size needed for the economic automotive engine, scaling down the 300 kw (402 hp) is beset by the laws of scale. The conventional four stroke diesel was not shown to be successful at the small high speed engine size. The opposed piston two stroke engine does not suffer the same laws of scale and engines in the low power range have already been marketed successfully. The half liter/cylinder Armstrong Whitworth Swing Beam Engine is the latest to be designed with the automotive market in mind. Its low noise structure and balanced linkage system coupled with advantages for easy start and potential use of low grade fuels, derived from its variable compression ratio and slow piston motion, qualifies it for the application.

  6. Temperature control of an automotive engine cooling system utilizing a magneto-rheological fan clutch

    International Nuclear Information System (INIS)

    Kim, Eun-Seok; Choi, Seung-Bok; Park, Young-Gee; Lee, Soojin

    2010-01-01

    In this note, the temperature control of an automotive engine cooling system is undertaken using a magneto-rheological (MR) fluid-based fan clutch (MR fan clutch in short). In order to achieve this goal, an appropriate size of controllable fan clutch using an MR fluid is firstly devised by considering the design parameters of a conventional fan clutch to reflect the practical application. Then, the principal design parameters of the MR fan clutch such as the length of the disc are optimally determined through finite element analysis. The drum-type MR fan clutch is manufactured and its time response to input current is experimentally evaluated. A robust sliding mode controller is then formulated by treating the time constant of the fan clutch system as an uncertain parameter. After identifying the relationship between angular velocity of the MR fan clutch and the temperature of the cooling system, the sliding mode controller is experimentally realized for the cooling system. It has been clearly demonstrated that the proposed sliding mode controller follows well the desired temperature with a small regulating error. It is expected from this feasibility work that the proposed control system associated with an MR fan clutch can be effectively utilized for the automotive cooling system to improve the fuel efficiency. (technical note)

  7. Corrosion performance of Al-Si-Cu hypereutectic alloys in a synthetic condensed automotive solution

    Directory of Open Access Journals (Sweden)

    Hamilta de Oliveira Santos

    2005-06-01

    Full Text Available In this investigation the corrosion resistance of four Al-Si hypereutectic alloys in a solution typical of condensate from automotive fuel combustion products, and referred to here as synthetic condensed automotive solution, has been studied. Three commercial alloys that are used for cylinder liners, and a laboratory made alloy, were studied by electrochemical impedance spectroscopy and measurements were taken after increasing times of immersion in this solution. Comparison of the electrochemical response of the four alloys in the corrosive solution was carried out. Although the mechanisms by which the four alloys corroded were similar, the results indicated differences in corrosion resistances of these alloys, and these differences could be related to their microstructures. The laboratory prepared alloy showed increased susceptibility to pitting corrosion compared to the commercial alloys. The surfaces of the alloys were examined, before and after the corrosion test, by scanning electron microscopy and analyzed by energy dispersive spectroscopy. The results indicated preferential attack of the aluminium matrix phase in all the alloys. The alloy with higher copper content and prepared by spray forming was more susceptible to pitting compared to the other alloys. The EIS response at low frequencies indicated a diffusion-controlled process, probably that of oxygen to the alloy interface.

  8. Fuel Exhaling Fuel Cell.

    Science.gov (United States)

    Manzoor Bhat, Zahid; Thimmappa, Ravikumar; Devendrachari, Mruthyunjayachari Chattanahalli; Kottaichamy, Alagar Raja; Shafi, Shahid Pottachola; Varhade, Swapnil; Gautam, Manu; Thotiyl, Musthafa Ottakam

    2018-01-18

    State-of-the-art proton exchange membrane fuel cells (PEMFCs) anodically inhale H 2 fuel and cathodically expel water molecules. We show an unprecedented fuel cell concept exhibiting cathodic fuel exhalation capability of anodically inhaled fuel, driven by the neutralization energy on decoupling the direct acid-base chemistry. The fuel exhaling fuel cell delivered a peak power density of 70 mW/cm 2 at a peak current density of 160 mA/cm 2 with a cathodic H 2 output of ∼80 mL in 1 h. We illustrate that the energy benefits from the same fuel stream can at least be doubled by directing it through proposed neutralization electrochemical cell prior to PEMFC in a tandem configuration.

  9. Automotive Catalyst State Diagnosis Using Microwaves

    Directory of Open Access Journals (Sweden)

    Moos Ralf

    2015-01-01

    Full Text Available The state of catalysts plays a key role in automotive exhaust gas aftertreatment. The soot or ash loading of Diesel particulate filters, the oxygen loading degree in three-way catalysts, the amount of stored ammonia in SCR catalysts, or the NOx loading degree in NOx storage catalysts are important parameters that are today determined indirectly and in a model-based manner with gas sensors installed upstream and/or downstream of the catalysts. This contribution gives an overview on a novel approach to determine the catalyst state directly by a microwave-based technique. The method exploits the fact that the catalyst housing acts as a microwave cavity resonator. As “sensing” elements, one or two simple antennas are mounted inside the catalyst canning. The electrical properties of the catalyst device (ceramic honeycomb plus coating and storage material can be measured. Preferably, the resonance characteristics, e.g., the resonance frequencies, of selected cavity modes are observed. The information on the catalyst interior obtained in such a contactless manner is very well correlated with the catalyst state as will be demonstrated for different exhaust gas aftertreatment systems.

  10. Advanced Automotive Diesel Assessment Program, executive summary

    Science.gov (United States)

    1983-01-01

    The objectives of this analytical study were: to select one advanced automotive diesel engine (AAD) concept which would increase the tank mileage of a 3,000 pound passenger car from the present 35 mpg to at least 52 mpg; to identify long term component research and development work required to bring the selected concept to fruition; and to prepare a development strategy that will bring the selected concept to a prototype testing phase. Cummins Engine Company has completed this study. The selected concept is a 4 stroke cycle, direct injection, spark assisted, advanced adiabatic diesel engine with positive displacement compounding plus expander and part load air preheating. The engine does not use a liquid coolant nor liquid lubricants. It is a 4 cylinder, in-line, 77 mm bore x 77 mm stroke, 1.434 liters displacement engine weighing 300 lb, and rated at 70 BHP at 3000 rpm. Installation dimensions are 621 mm length x 589 mm width x 479 mm height (24.4 inch x 22 inch x 18.9 inch).

  11. Protectionism in the Colombian automotive industry

    Directory of Open Access Journals (Sweden)

    Carlos Ronderos

    2014-10-01

    Full Text Available This paper employs the concept of Effective Protection in order to calculate the real level of protection that has favored the automotive assembly industry in Colombia and to value if this level of protection has helped to achieve the goals of an Import Substitution Policy. A policy that seeks to establish, through this protection mechanism a national industry of consumer durable goods, with an increasing share of domestic inputs generating alongside new dynamics in investment and employment generation. For this purpose, this paper works with data from the Colombian National Manufacture Survey (Encuesta Nacional Manufacturera de Colombia, data provided by the industry on incorporation of local inputs, and a review of changes in policy and legislation affecting the way in which this mechanism operates. Contrary to what would be expected, analysis shows that share of local inputs has decreased, bringing as a result that the cost of protection has been very high when compared to investment and employment generation. The paper concludes with some thoughts as to the convenience of maintaining this type of policy.

  12. Remanufacturing in automotive industry: Challenges and limitations

    Directory of Open Access Journals (Sweden)

    Paulina Golinska

    2011-10-01

    Full Text Available Purpose: The aim of this paper is to provide the framework for management of reverse flow of materials in automotive industry. The emphasis is placed on the remanufacturing activities. Materials management in such conditions is a real challenge. The cause for this is parallel use of raw materials and reused materials. Such hybrid flows of materials are characterized by increased level of uncertainty connected with amount, quality and timing. Design/methodology/approach: This paper presents a comprehensive review of remanufacturing and traditional manufacturing. The stabilization of reverse flows is crucial for continuity of remanufacturing operations. The simulation model and results are discussed regarding stabilization of the reverse flows. Findings: Authors identify main problems that appear in the area of combining at the production system forward and reverse flows of materials. The agent-based technology is applied for configuration and stabilization of reverse network. Research limitations/implications: Paper is case – oriented. Practical implications: Both logistician and IT researchers might benefit from authors approach. Originality/value: Authors provide an interdisciplinary approach combining operations management, logistics and information technology.

  13. Carbon footprint of automotive ignition coil

    Science.gov (United States)

    Chang, Huey-Ling; Chen, Chih-Ming; Sun, Chin-Huang; Lin, Hung-Di

    2015-07-01

    In recent years, environmental issues, such as climate change and global warming due to the excessive development of industry, have attracted increasing attention of citizens worldwide. It is known that CO2 accounts for the largest proportion of greenhouse gases. Therefore, how to reduce CO2 emissions during the life cycle of a product to lessen its impact on environment is an important topic in the industrial society. Furthermore, it is also of great significance to cut down the required energy so as to lower its production costs during the manufacturing process nowadays. This study presents the carbon footprint of an automotive ignition coil and its partial materials are defined to explore their carbon emissions and environmental impact. The model IPCC GWP100a calculates potential global greenhouse effect by converting them into CO2 equivalents. In this way, the overall carbon footprint of an ignition coil can be explored. By using IPCC GWP100a, the results display that the shell has the most carbon emissions. The results can help the industry reduce the carbon emissions of an ignition coil product.

  14. Implementing Automotive Telematics for Fleet Insurance

    Directory of Open Access Journals (Sweden)

    Marika Azzopardi

    2013-12-01

    Full Text Available The advantages of Usage-Based Insurance for automotive covers over conventional rating methods have been discussed in literature for over four decades. Notwithstanding their adoption in insurance markets has been slow. This paper seeks to establish the viability of introducing fleet Telematics-Based Insurance by investigating the perceptions of insurance operators, tracking service providers and corporate fleet owners. At its core, the study involves a SWOT-analysis to appraise Telematics-Based Insurance against conventional premium rating systems. Twenty five key stakeholders in Malta, a country with an insurance industry that represents others in microcosm, were interviewed to develop our analysis. We assert that local insurers have interests in such insurance schemes as enhanced fleet management and monitoring translate into an improved insurance risk. The findings presented here have implications for all stakeholders as we argue that telematics enhance fleet management, TBI improves risk management for insurers and adoption of this technology is dependent on telematics providers increasing the perceived control by insurers over managing this technology.

  15. Models and optimization of solar-control automotive glasses

    Science.gov (United States)

    Blume, Russell Dale

    Efforts to develop automotive glasses with enhanced solar control characteristics have been motivated by the desire for increased consumer comfort, reduced air-conditioning loads, and improved fuel-economy associated with a reduction in the total solar energy transmitted into the automotive interior. In the current investigation, the base soda-lime-silicate glass (72.7 wt.% SiO 2, 14.2% Na2O, 10.0% CaO, 2.5% MgO, 0.6% Al2O 3 with 0.3 Na2SO4 added to the batch as a fining agent) was modified with Fe2O3 (0.0 to 0.8%), NiO (0.0 to 0.15%), CoO (0.0 to 0.15%), V2O5 (0.0 to 0.225%), TiO2 (0.0 to 1.5%), SnO (0.0 to 3.0%), ZnS (0.0 to 0.09%), ZnO (0.0 to 2.0%), CaF2 (0.0 to 2.0%), and P2O5 (0.0 to 2.0%) to exploit reported non-linear mechanistic interactions among the dopants by which the solar-control characteristics of the base glass can be modified. Due to the large number of experimental variables under consideration, a D-optimal experimental design methodology was utilized to model the solar-optical properties as a function of batch composition. The independent variables were defined as the calculated batch concentrations of the primary (Fe2O 3, NiO, CoO, V2O5) and interactive (CaF2 , P2O5, SnO, ZnS, ZnO, TiO2) dopants in the glass. The dependent variable was defined as the apparent optical density over a wavelength range of 300--2700 nm at 10 nm intervals. The model form relating the batch composition to the apparent optical density was a modified Lambert-Beer absorption law; which, in addition to the linear terms, contained quadratic terms of the primary dopants, and a series of binary and ternary non-linear interactions amongst the primary and interactive dopants. Utilizing the developed model, exceptional fit in terms of both the discrete response (the transmission curves) and the integrated response (visible and solar transmittance) were realized. Glasses utilizing Fe2O 3, CoO, NiO, V2O5, ZnO and P2O 5 have generated innovative glasses with substantially improved

  16. Deployment of ERP Systems at Automotive Industries, Security Inspection (Case Study: IRAN KHODRO Automotive Company)

    Science.gov (United States)

    Ali, Hatamirad; Hasan, Mehrjerdi

    Automotive industry and car production process is one of the most complex and large-scale production processes. Today, information technology (IT) and ERP systems incorporates a large portion of production processes. Without any integrated systems such as ERP, the production and supply chain processes will be tangled. The ERP systems, that are last generation of MRP systems, make produce and sale processes of these industries easier and this is the major factor of development of these industries anyhow. Today many of large-scale companies are developing and deploying the ERP systems. The ERP systems facilitate many of organization processes and make organization to increase efficiency. The security is a very important part of the ERP strategy at the organization, Security at the ERP systems, because of integrity and extensive, is more important of local and legacy systems. Disregarding of this point can play a giant role at success or failure of this kind of systems. The IRANKHODRO is the biggest automotive factory in the Middle East with an annual production over 600.000 cars. This paper presents ERP security deployment experience at the "IRANKHODRO Company". Recently, by launching ERP systems, it moved a big step toward more developments.

  17. Component Analysis of Deposits in Selective Catalytic Reduction System for Automotive Diesel Engine

    Directory of Open Access Journals (Sweden)

    Zhu Neng

    2016-01-01

    Full Text Available In this paper, deposits in exhaust pipes for automotive diesel engines were studied by various chemical analysis methods and a kind of analysis process to determine the compositions of organic matter was proposed. Firstly, the elements of the deposits were determined through the element analysis method. Then using characteristic absorption properties of organic functional groups to the infrared spectrum, the functional groups in the deposits were determined. Finally, by GC-MS (gas chromatography - mass spectrometry test, the content of each main component was determined quantitatively. Element analysis results indicated that the deposits adsorbed metal impurities from fuel oil, lubricating oil, mechanical wear and urea water solution. The result of GC-MS test showed that the area percentage of cyanuric acid was the biggest (about 85%, the second was urea (about 4%, and the content of biuret and biurea was scarce.

  18. Innovative design, analysis and development practices in aerospace and automotive engineering

    CERN Document Server

    Chandrasekhar, U; Arankalle, Avinash

    2014-01-01

    The book presents the best articles presented by researchers, academicians and industrial experts in the International Conference on “Innovative Design, Analysis and Development Practices in Aerospace and Automotive Engineering”. The book discusses new concept designs, analysis and manufacturing technologies, where more swing is for improved performance through specific and/or multifunctional linguistic design aspects to downsize the system, improve weight to strength ratio, fuel efficiency, better operational capability at room and elevated temperatures, reduced wear and tear, NVH aspects while balancing the challenges of beyond Euro IV/Barat Stage IV emission norms, Greenhouse effects and recyclable materials. The innovative methods discussed in the book will serve as a reference material for educational and research organizations, as well as industry, to take up challenging projects of mutual interest.

  19. 16th International Forum on Advanced Microsystems for Automotive Applications (AMAA)

    CERN Document Server

    Advanced Microsystems for Automotive Applications 2012 : Smart Systems for Safe, Sustainable and Networked Vehicles

    2012-01-01

    The ambitious objectives of future road mobility, i.e. fuel efficiency, reduced emissions, and zero accidents, imply a paradigm shift in the concept of the car regarding its architecture, materials, and propulsion technology, and require an intelligent integration into the systems of transportation and power. ICT, components and smart systems have been essential for a multitude of recent innovations, and are expected to be key enabling technologies for the changes ahead, both inside the vehicle and at its interfaces for the exchange of data and power with the outside world. It has been the objective of the International Forum on Advanced Microsystems for Automotive Applications (AMAA) for almost two decades to detect novel trends and to discuss technological implications and innovation potential from day one on. In 2012, the topic of the AMAA conference is “Smart Systems for Safe, Sustainable and Networked Vehicles”. The conference papers selected for this book address current research, developments and i...

  20. International Conference on Innovative Design and Development Practices in Aerospace and Automotive Engineering

    CERN Document Server

    Chandrasekhar, U

    2017-01-01

    The book presents the best articles presented by researchers, academicians and industrial experts in the International Conference on “Innovative Design and Development Practices in Aerospace and Automotive Engineering (I-DAD 2016)”. The book discusses new concept designs, analysis and manufacturing technologies, where more swing is for improved performance through specific and/or multifunctional linguistic design aspects to downsize the system, improve weight to strength ratio, fuel efficiency, better operational capability at room and elevated temperatures, reduced wear and tear, NVH aspects while balancing the challenges of beyond Euro IV/Barat Stage IV emission norms, Greenhouse effects and recyclable materials. The innovative methods discussed in the book will serve as a reference material for educational and research organizations, as well as industry, to take up challenging projects of mutual interest.

  1. Caterpillar C7 and GEP 6.5L (T) Fuel System Durability Using 25% ATJ Fuel Blend

    Science.gov (United States)

    2015-02-01

    UNCLASSIFIED x ACRONYMS AND ABBREVIATIONS ATJ – alcohol to jet BSFC – brake specific fuel consumption CAT – Caterpillar CI/LI – corrosion inhibitor...hp – horsepower hr/hrs – hour/hours JP8 – jet propulsion 8 L - liter Ft-lb – pound feet torque MATV – MRAP All Terrain Vehicle MRAP – Mine...Southwest Research Institute T - turbo TARDEC – Tank Automotive Research, Development, and Engineering Center TFLRF – TARDEC Fuels and Lubricants

  2. Evolution of the Automotive Body Coating Process—A Review

    Directory of Open Access Journals (Sweden)

    Nelson K. Akafuah

    2016-06-01

    Full Text Available Automotive coatings and the processes used to coat automobile surfaces exemplify the avant-garde of technologies that are capable of producing durable surfaces, exceeding customers’ expectations of appearance, maximizing efficiency, and meeting environmental regulations. These accomplishments are rooted in 100 years of experience, trial-and-error approaches, technique and technology advancements, and theoretical assessments. Because of advancements directed at understanding the how, why, when, and where of automobile coatings, the progress in controlling droplets and their deposition attributes, and the development of new technologies and paint chemistries, a comprehensive and up-to-date review of automobile coatings and coating technologies was considered to be of value to industrial practitioners and researchers. Overall, the critical performance factors driving the development and use of advanced automotive coatings and coating technologies are (a aesthetic characteristics; (b corrosion protection; (c mass production; (d cost and environmental requirements; and (e appearance and durability. Although the relative importance of each of these factors is debatable, the perfection of any one at the expense of another would be unacceptable. Hence, new developments in automotive coatings are described and discussed in the following review, and then related to improvements in production technologies and paints. Modern automotive coating procedures are also discussed in detail. Finally, an extrapolation into the future of automotive coating is offered with a view of the developments and technologies needed for an increasingly efficient and more sustainable coatings industry.

  3. DISAIN SIMULATOR AUTOMOTIVE AIR CONDITIONING UNTUK MENINGKATKAN KOMPETENSI MAHASISWA

    Directory of Open Access Journals (Sweden)

    Kamin Sumardi

    2015-08-01

    Full Text Available Perkembangan teknologi automotive air conditioning dan aplikasinya sangat cepat, salah satunya dengan menerapkan green technology. Penerapan green technology pada teknologi air conditioning, karena masih menggunakan refrigeran yang mengandung unsur kimia yang merusak lapisan ozon dan pemanasan global. Alih teknologi bidang air conditioning yang ramah lingkungan, belum dibarengi dengan ketersediaan tenaga kerja pada tingkat SMK dan perguruan tinggi yang memadai, baik kuantitas maupun kompetensinya. Pada level SMK dan perguruan tinggi, kompetensi akademik dan vokasional bidang automotive air conditioning harus terus ditingkatkan dan diperbaharui sesuai dengan perkembangan teknologinya. Penelitian ini bertujuan untuk menghasilkan simulator automotive air conditioner dan model pembelajaran tata udara pada otomotif berwawasan teknologi ramah lingkungan. Penelitian menggunakan metode research and development dengan langkah-langkah: studi pendahuluan, perencanaan, pengembangan melalui uji coba simulator, validasi, dan produk akhir. Simulator dibuat sesuai dengan kondisi di dunia kerja agar tidak terjadi miskonsepsi dan mala-praktek automotive air conditioning. Simulator ini dibuat secara kompak dan mobile atau dapat dipindah dan dibawa. Model pembelajaran disesuaikan dengan kebutuhan kompetensi yang dipersyaratkan. Hasil penelitian menunjukkan bahwa dengan bantuan simulator automotive air conditioner dan model pembelajaran yang tepat mahasiswa mampu menyerap konsep dan praktek lebih cepat 85%. Hasil belajar pada ranah afektif, kognitif, psikomotor dan kompetensi meningkat secara signifikan.

  4. Developing e-learning solutions in the automotive industry

    Directory of Open Access Journals (Sweden)

    Razvan Virgil Bogdan

    2016-07-01

    Full Text Available In the rapid developing market of automotive industry, cutting-edge technologies are being introduced. One such example is the AUTOSAR standard. Companies are investing a large amount of finances for the training of their employees into the intricacies of such technologies. In order to face such an increase of the training costs, automotive corporation have started lately switching their approach to e-Learning systems. This paper presents an e-Learning approach developed in the automotive industry in order to address the demands of teaching AUTOSAR standard. The developed e-Learning project is called Academy. In order to develop the e-Learning solution we focused on the Software Development part of automotive industry. Therefore we had to gather the ideas from different trainers, come with a common approach and use specific techniques so that the trainee should get a real feeling of the material. It is presented the design, implementation and evaluation of this e-Learning solution, but more than that faced issues and learned lessons. Developing this solution has offered different insights into how to approach such a task which are useful for the further expansion of the project, but also for future researchers who might encounter such a challenge of developing e-Learning solutions for the automotive industry. These are all grouped in a set of guidelines related to following a model of implementation, getting track of participants, user interaction with the AUTOSAR standard, test and production development and so on.

  5. Change management methodologies trained for automotive infotainment projects

    Science.gov (United States)

    Prostean, G.; Volker, S.; Hutanu, A.

    2017-01-01

    An Automotive Electronic Control Units (ECU) development project embedded within a car Environment is constantly under attack of a continuous flow of modifications of specifications throughout the life cycle. Root causes for those modifications are for instance simply software or hardware implementation errors or requirement changes to satisfy the forthcoming demands of the market to ensure the later commercial success. It is unavoidable that from the very beginning until the end of the project “requirement changes” will “expose” the agreed objectives defined by contract specifications, which are product features, budget, schedule and quality. The key discussions will focus upon an automotive radio-navigation (infotainment) unit, which challenges aftermarket devises such as smart phones. This competition stresses especially current used automotive development processes, which are fit into a 4 Year car development (introduction) cycle against a one-year update cycle of a smart phone. The research will focus the investigation of possible impacts of changes during all phases of the project: the Concept-Validation, Development and Debugging-Phase. Building a thorough understanding of prospective threats is of paramount importance in order to establish the adequate project management process to handle requirement changes. Personal automotive development experiences and Literature review of change- and configuration management software development methodologies led the authors to new conceptual models, which integrates into the structure of traditional development models used in automotive projects, more concretely of radio-navigation projects.

  6. Advanced Automotive Technologies annual report to Congress, fiscal year 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This annual report serves to inform the United States Congress on the progress for fiscal year 1996 of programs under the Department of Energy`s Office of Advanced Automotive Technologies (OAAT). This document complies with the legislative requirement to report on the implementation of Title III of the Automotive Propulsion Research and Development Act of 1978. Also reported are related activities performed under subsequent relevant legislation without specific reporting requirements. Furthermore, this report serves as a vital means of communication from the Department to all public and private sector participants. Specific requirements that are addressed in this report are: Discussion of how each research and development contract, grant, or project funded under the authority of this Act satisfies the requirements of each subsection; Current comprehensive program definition for implementing Title III; Evaluation of the state of automotive propulsion system research and development in the United States; Number and amount of contracts and grants awarded under Title III; Analysis of the progress made in developing advanced automotive propulsion system technology; and Suggestions for improvements in automotive propulsion system research and development, including recommendations for legislation.

  7. Overview of Automotive Core Tools: Applications and Benefits

    Science.gov (United States)

    Doshi, Jigar A.; Desai, Darshak

    2017-08-01

    Continuous improvement of product and process quality is always challenging and creative task in today's era of globalization. Various quality tools are available and used for the same. Some of them are successful and few of them are not. Considering the complexity in the continuous quality improvement (CQI) process various new techniques are being introduced by the industries, as well as proposed by researchers and academia. Lean Manufacturing, Six Sigma, Lean Six Sigma is some of the techniques. In recent years, there are new tools being opted by the industry, especially automotive, called as Automotive Core Tools (ACT). The intention of this paper is to review the applications and benefits along with existing research on Automotive Core Tools with special emphasis on continuous quality improvement. The methodology uses an extensive review of literature through reputed publications—journals, conference proceedings, research thesis, etc. This paper provides an overview of ACT, its enablers, and exertions, how it evolved into sophisticated methodologies and benefits used in organisations. It should be of value to practitioners of Automotive Core Tools and to academics who are interested in how CQI can be achieved using ACT. It needs to be stressed here that this paper is not intended to scorn Automotive Core Tools, rather, its purpose is limited only to provide a balance on the prevailing positive views toward ACT.

  8. The use of methanol as a fuel for transportation

    Energy Technology Data Exchange (ETDEWEB)

    Egebaeck, K.E. [Luleaa Univ. of Technology (Sweden); Walsh, M.P. [Arlington, VA (United States); Westerholm, R. [Stockholm Univ. (Sweden)

    1997-06-01

    The aim of the project was to collect and report international experiences concerning the use of methanol as an automotive fuel. The method has been to study the literature which covers the subject and most of the information has been collected that way. The project started with a participation in a conference and a visit to people who have been involved in activities concerning the use of automotive alcohols. Car manufacturers, environmental authorities and users of alcohol fuels i.e. representatives of bus companies, were interviewed. The different applications for the use of methanol as an automotive fuel has been described in the report as well as the production of methanol. Some results, mostly in form of emission data and other experiences derived from the use of alcohol fuels, have also been presented. The use of ethanol and methanol has been compared and based on information from engine manufacturers and users of alcohol fueled vehicles there seems to be a preference for the use of ethanol. However, the question `methanol or ethanol` has not been answered as the decision which of the two is to be used seems to depend more on economic factors, such as cost of the production of the fuel etc., than on other factors. 165 refs, 15 figs, 14 tabs

  9. Automotive Manufacturing and Repair Technician Employment

    Science.gov (United States)

    McAlinden, Sean P.

    2013-01-01

    It's been more than three years since the U.S. automobile industry nearly collapsed. A controversial federal bailout, an increase in consumer demand, and a growing interest in environmentally friendly fuel-efficient vehicles and related technologies have combined to help create a remarkable recovery. Total U.S. sales of light vehicles in 2012 are…

  10. Relationship value antecedents in the South African automotive component supply chain

    Directory of Open Access Journals (Sweden)

    Aletta S. Tolmay

    2017-05-01

    Practical/managerial implications: It is suggested that superior supply chain practices within the South African automotive industry might secure business retention. Automotive component suppliers are therefore advised to implement relationship value strategies to promote higher value through personal interaction.

  11. Social media for knowledge sharing in automotive repair

    CERN Document Server

    Finkbeiner, Patric

    2017-01-01

    This book explores, describes and explains the predictors essential for the acceptance of social media as a digital platform to share professional knowledge in the field of automotive repair in Germany. It reports a rigorous literature review covering key elements of social media, knowledge management and technology acceptance studies. The book assumes a pragmatist approach and applies mixed methods in an exploratory sequential design, combining qualitative and quantitative methods to ensure robust collection and analysis of the collected data. Based on a survey on German automotive repair shops, the author provides a framework, for various stakeholders, to comprehend the motivations for knowledge sharing for automotive repair professionals in Germany. This book not only adds to the existing academic body of knowledge but also provides implications for industry and legislation on a European scale. .

  12. Financial Crises and Automotive Industry Development in Southeast Asia

    DEFF Research Database (Denmark)

    Doner, Richard F.; Wad, Peter

    2014-01-01

    The automotive industries of Southeast Asia have grown significantly but unevenly. Thailand has outperformed its neighbours in Malaysia, Indonesia and the Philippines with regard to production and, most notably, export volumes. But the Thai auto industry has not exhibited the level of local...... (indigenous) technology capacity and input growth seen in South Korea, Taiwan and, increasingly, in China. The 1997–98 and 2008 financial and economic crises generally reinforced pre-existing national automotive strategies, but to different degrees: They strongly accelerated an earlier Thai move to exports...... whose very success weakened pressures for upgrading; encouraged more moderate automotive liberalisation in Indonesia and, to a lesser extent, in the Philippines; but promoted only minimal changes to Malaysia’s relatively protectionist national car strategy. The fact that the crises served more...

  13. Environmental management and operational performance in automotive companies in Brazil

    DEFF Research Database (Denmark)

    Jabbour, C.J.C.; De Sousa Jabbour, A.B.L.; Govindan, Kannan

    2013-01-01

    The main objective of this study is to verify the influence of Environmental Management (EM) on Operational Performance (OP) in Brazilian automotive companies, analyzing whether Lean Manufacturing (LM) and Human Resources (HR) interfere in the greening of these companies. Therefore, a conceptual...... framework listing these concepts was proposed, and three research hypotheses were presented. A questionnaire was elaborated based on this theoretical background and sent to respondents occupying the highest positions in the production/operations areas of Brazilian automotive companies. The data, collected....... The originality of this paper lies in its gathering the concepts of EM, LM, HR and OP in a single study, as they generally tend not to be treated jointly. This paper also provided valid empirical evidence for a littlestudied context: the Brazilian automotive sector....

  14. Learning, Upgrading, Innovation in the South African Automotive Industry

    DEFF Research Database (Denmark)

    Barnes, Justin; Lorentzen, Jochen

    2003-01-01

    This paper addresses the innovation activities of automotive component manufacturers in South Africa. It looks at the technological trajectory of a handful of firms that stand out from the crowd and analyses the results of their endeavours in the context of their interaction with foreign capital......, their internal upgrading and R&D agenda, and their interface with South Africa's national innovation system (NIS). The analysis makes use of eight case studies, and illustrates the conditions under which indigenous innovation in the automotive industries can happen in a developing country. This finding...... and output from the tertiary education sector on the other. Open questions that need further attention include among others the overall functioning of the NIS, and changes over time in the perception of local innovation potential by car assemblers.Keywords: automotive industry, developing countries...

  15. Identifying Lead Markets in the European Automotive Industry

    DEFF Research Database (Denmark)

    Cleff, Thomas; Grimpe, Christoph; Rammer, Christian

    2015-01-01

    This paper presents an indicator-based methodology to identify lead markets in the European automotive industry. The lead market approach tries to explain why certain countries are better positioned than others for developing and launching new products. While much research stresses the role...... design. We use an indicator-based approach which has been successfully employed for individual products as well as for various industries in order to identify lead markets in the European automotive industry. Employing five lead market factors, our results show that the EU is by far no homogeneous market...... for automobiles and national markets differ considerably in their lead market potential. The German market is found to be most promising to serve as a lead market, while other European countries with a strong automotive tradition like France, Italy, the UK, and Sweden score lower. Our findings suggest that firms...

  16. Digitalization of automotive industry – scenarios for future manufacturing

    Directory of Open Access Journals (Sweden)

    Peters Steven

    2016-01-01

    Full Text Available Among the current challenges to the global automotive industry are changes in global markets leading to product variety, regulation leading to pressure for new technologies in body and powertrain, and competition by new players such as huge information and communication technology companies. Automotive original equipment manufacturers (OEMs deal with these issues in different ways. This paper uses the scenario technique to illustrate possible answers to the question, how future value chains of automotive industry will look like. In almost all cases, information and communication technology (ICT plays a major role in future strategies to cope with the aforementioned challenges. On the one hand, ICT can boost the way to more efficient production of variants by utilizing smart manufacturing approaches, on the other hand ICT enables new features such as autonomous driving.

  17. Offshoring trends in the manufacturing process within the automotive industry

    DEFF Research Database (Denmark)

    Simplay, S.; Hansen, Zaza Nadja Lee

    2014-01-01

    engineering activities. This development has created several challenges. These challenges arose as organisations are not considering how offshoring activities could be integrated with an increasingly global supply chain for the manufacturing of the final product. The paper contributes to manufacturing theory......This paper investigates offshoring trends in the automotive industry. The research approach consisted of combining empirical findings from case companies with latest research from the field. Empirical data was collected through case studies from 15 automotive organisations based in Europe...... consisting of original equipment manufacturers and engineering service providers. The findings indicated some offshoring trends in the automotive industry. Offshoring in this industry is moving from a manufacturing focus to incorporate large parts of the process, including high-level product development...

  18. OASIS: An automotive analysis and safety engineering instrument

    International Nuclear Information System (INIS)

    Mader, Roland; Armengaud, Eric; Grießnig, Gerhard; Kreiner, Christian; Steger, Christian; Weiß, Reinhold

    2013-01-01

    In this paper, we describe a novel software tool named OASIS (AutOmotive Analysis and Safety EngIneering InStrument). OASIS supports automotive safety engineering with features allowing the creation of consistent and complete work products and to simplify and automate workflow steps from early analysis through system development to software development. More precisely, it provides support for (a) model creation and reuse, (b) analysis and documentation and (c) configuration and code generation. We present OASIS as a part of a tool chain supporting the application of a safety engineering workflow aligned with the automotive safety standard ISO 26262. In particular, we focus on OASIS' (1) support for property checking and model correction as well as its (2) support for fault tree generation and FMEA (Failure Modes and Effects Analysis) table generation. Finally, based on the case study of hybrid electric vehicle development, we demonstrate that (1) and (2) are able to strongly support FTA (Fault Tree Analysis) and FMEA

  19. An Elderly Employment Model For The Thai Automotive Industry

    Directory of Open Access Journals (Sweden)

    Pornrat Sadangharn

    2017-10-01

    Full Text Available This research aims at studying an elderly employment model for the Thai automotive industry. Mixed methods with a sequential exploratory strategy were utilized. Grounded theory was employed by using in-depth interviews to investigate the characteristics of elderly employment in the Thai automotive industry. For this stage of the research, theoretical and purposive sampling was used to select 32 key informants from four groups of stakeholders: (1 elderly workers, (2 employers or human resource managers, (3 government officers, and (4 academics. The findings were then validated using a quantitative approach with structural equation modelling (SEM. A total of 308 elderly workers and human resource managers were surveyed regarding their opinion about elderly employment. Based on the survey, the elderly employment model in the Thai automotive industry, which is comprised of the approach to elderly employment, elderly employment preparation, and key success factors for elderly employment, was revealed to be a good fit. 

  20. Exposure to automotive pollution increases plasma susceptibility to oxidation.

    Science.gov (United States)

    Sharman, James E; Coombes, Jeff S; Geraghty, Dominic P; Fraser, David I

    2002-01-01

    Low-density lipoprotein oxidation is implicated in the development of atherosclerosis. Plasma susceptibility to oxidation may be used as a marker of low-density lipoprotein oxidation and thus predict atherosclerotic risk. In this study the authors investigated the relationship between plasma susceptibility to oxidation and exposure to automotive pollution in a group of automobile mechanics (n = 16) exposed to high levels of automotive pollution, vs. matched controls (n = 13). The authors induced plasma oxidation by a free radical initiator and they determined susceptibility to oxidation by (1) change in absorbance at 234 nm, (2) lag time to conjugated diene formation, and (3) linear slope of the oxidation curve. Mechanics had significantly higher values (mean +/- standard error) for change in absorbance (1.60 +/- 0.05 vs. 1.36 +/- 0.05; p automotive pollutants increases plasma susceptibility to oxidation and may, in the long-term, increase the risk of developing atherosclerosis.

  1. Making aerospace technology work for the automotive industry - Introduction

    Science.gov (United States)

    Olson, W. T.

    1978-01-01

    In many cases it has been found that advances made in one technical field can contribute to other fields. An investigation is in this connection conducted concerning subjects from contemporary NASA programs and projects which might have relevance and potential usefulness to the automotive industry. Examples regarding aerospace developments which have been utilized by the automotive industry are related to electronic design, computer systems, quality control experience, a NASA combustion scanner and television display, exhaust gas analyzers, and a device for suppressing noise propagated through ducts. Projects undertaken by NASA's center for propulsion and power research are examined with respect to their value for the automotive industry. As a result of some of these projects, a gas turbine engine and a Stirling engine might each become a possible alternative to the conventional spark ignition engine.

  2. A Case Study: Designing for Sustainability and Reliability in an Automotive Seat Structure

    Directory of Open Access Journals (Sweden)

    Celalettin Yuce

    2014-07-01

    Full Text Available Recently, sustainability has been a growing concern for many industries and especially for the transportation sector due to it being the second largest energy consumer and largest contributor of anthropogenic greenhouse gas emissions within the European Union. New legal restrictions on the emission rates have forced the automotive sector to examine different fuel-efficient technologies. Vehicle weight reduction is one of the most important methods of improving fuel efficiency and reducing CO2 emissions. Accordingly, lighter, safer, more fuel efficient, and environmentally sustainable vehicles are a priority for European authorities. In the present work, the passenger seat structure was considered as the area for lightweighting due to its important role in the mass of commercial vehicles in terms of numbers per vehicle. In addition, seat structures presented the best opportunity for weight reduction using new materials and design techniques. Detailed (3D finite element models of passenger seats were developed for finite element analyses (FEA. To obtain a lightweight and safe seat structure, different materials and thicknesses of profiles were analyzed. Lightweight passenger seat prototypes were developed and an overall 20% weight reduction was achieved including the structural frame, chassis and pillar. In addition, the new passenger seat meets ECE R14 safety norms.

  3. A COMPUTATIONAL FLUID DYNAMICS ANALYSIS OF AIR FLOW THROUGH A TELECOM BACK-UP UNIT POWERED BY AN AIR-COOLED PROTON EXCHANGE MEMBRANE FUEL CELL

    DEFF Research Database (Denmark)

    Gao, Xin; Berning, Torsten; Kær, Søren Knudsen

    2016-01-01

    . This product heat has to be effectively removed from the fuel cell, and while automotive fuel cells are usually liquid-cooled using a secondary coolant loop similar to the internal combustion engines, stationary fuel cell systems as they are used for telecom back-up applications often rely on excessive air fed......Proton exchange membrane fuel cells (PEMFC’s) are currently being commercialized for various applications ranging from automotive to stationary such as powering telecom back-up units. In PEMFC’s, oxygen from air is internally combined with hydrogen to form water and produce electricity and heat...

  4. Beyond survival: Challenges facing South African automotive component exporters

    Directory of Open Access Journals (Sweden)

    M. J. Naude

    2006-12-01

    Full Text Available Purpose and Objective: The South African automotive component industry faces huge challenges in a very competitive global market. The primary focus of this research article is to determine the challenges facing exporters within this industry with special reference to selected sub-sectors. The challenges are approached from a supply chain perspective only. Problem Investigated: The research problem of this study was to identify these unique challenges and ascertain whether the implementation of a 'philosophy of continuous improvement' could be used as a strategic tool to address the challenges they face in the market. Methodology: This study included a combination of literature review, interviews with managers in the selected sub-groups and questionnaires sent out to determine the challenges facing automotive component exporters. In order to test the content validity and the reliability of the questionnaire, a pilot study was conducted at two organisations that are the main suppliers of automotive filters for passenger vehicles. The non-probability convenience sample technique was used to select the sample and consisted of selected sub-sectors that contribute 64,1% of the total value of automotive component exports in South Africa. Out of twenty-seven questionnaires sent out, twenty (74% response rate were duly completed by the respondents and returned to the researcher. Findings: South Africa faces unique challenges and these are listed and ranked according to priority from most to least important as follows: 1. The reduction of production costs; 2. R/US$ exchange rate effect on the respondent's export sales and profit margin; 3. Exchange rate fluctuations; 4. Threats to the local automotive component market; and 5. Increased competition by way of manufactured imports being sold in the South African market. Value of Research: The study provides recommendations that can be used within the automotive component industry.

  5. Methanator fueled engines for pollution control

    Science.gov (United States)

    Cagliostro, D. E.; Winkler, E. L.

    1973-01-01

    A methanator fueled Otto-cycle engine is compared with other methods proposed to control pollution due to automobile exhaust emissions. The comparison is made with respect to state of development, emission factors, capital cost, operational and maintenance costs, performance, operational limitations, and impact on the automotive industries. The methanator fueled Otto-cycle engine is projected to meet 1975 emission standards and operate at a lower relative total cost compared to the catalytic muffler system and to have low impact. Additional study is required for system development.

  6. A Study of the Awareness Level of Electric Vehicle Technology in California Community College Automotive Curriculums.

    Science.gov (United States)

    Keyzer, James

    California automotive technician programs were surveyed regarding their awareness of the impact that mandates of the Clean Air Act would have on their automotive technology programs. A questionnaire was sent to 100 California community colleges with an automotive technology program; 49 usable questionnaires were returned. A possible byproduct of…

  7. Simulation work of fatigue life prediction of rubber automotive components

    International Nuclear Information System (INIS)

    Samad, M S A; Ali, Aidy

    2010-01-01

    The usage of rubbers has always been so important, especially in automotive industries. Rubbers have a hyper elastic behaviour which is the ability to withstand very large strain without failure. The normal applications for rubbers are used for shock absorption, sound isolation and mounting. In this study, the predictions of fatigue life of an engine mount of rubber automotive components were presented. The finite element analysis was performed to predict the critical part and the strain output were incorporated into fatigue model for prediction. The predicted result shows agreement in term of failure location of rubber mount.

  8. Automotive SOI-BCD Technology Using Bonded Wafers

    International Nuclear Information System (INIS)

    Himi, H.; Fujino, S.

    2008-01-01

    The SOI-BCD device is excelling in high temperature operation and noise immunity because the integrated elements can be electrically separated by dielectric isolation. We have promptly paid attention to this feature and have concentrated to develop SOI-BCD devices seeking to match the automotive requirement. In this paper, the feature technologies specialized for automotive SOI-BCD devices, such as buried N + layer for impurity gettering and noise shielding, LDMOS with improved ESD robustness, crystal defect-less process, and wafer direct bonding through the amorphous layer for intelligent power IC are introduced.

  9. Towards a Load Balancing Middleware for Automotive Infotainment Systems

    Science.gov (United States)

    Khaluf, Yara; Rettberg, Achim

    In this paper a middleware for distributed automotive systems is developed. The goal of this middleware is to support the load bal- ancing and service optimization in automotive infotainment and entertainment systems. These systems provide navigation, telecommunication, Internet, audio/video and many other services where a kind of dynamic load balancing mechanisms in addition to service quality optimization mechanisms will be applied by the developed middleware in order to improve the system performance and also at the same time improve the quality of services if possible.

  10. NEW TRENDS AND CHELLENGES IN AUTOMOTIVE INDUSTRY LOGISTICS OPERATIONS

    Directory of Open Access Journals (Sweden)

    Dušan Sabadka

    2015-03-01

    Full Text Available This paper lays out the main features of the global automotive industry and identifies several important trends. Logistics operations (inbound and outbound in the automotive supply chain are complex and account for large expenses and therefore are segments in the value chainwhere improvements can be made. Better coordination between inbound and outbound logistics contributes to optimising the supply chains, to reducing inventories and to responding to consumer requests. As economies grow, the competition shifts towards brand image and customisation and here the speed and reliability of logistics operations becomes a critical elements.

  11. Modifications for use of methanol or methanol-gasoline blends in automotive vehicles, September 1976-January 1980

    Energy Technology Data Exchange (ETDEWEB)

    Patterson, D.J.; Bolt, J.A.; Cole, D.E.

    1980-01-01

    Methanol or blends of methanol and gasoline as automotive fuels may be attractive means for extending the nation's petroleum reserves. The present study was aimed at identifying potential problems and solutions for this use of methanol. Retrofitting of existing vehicles as well as future vehicle design have been considered. The use of ethanol or higher alcohols was not addressed in this study but will be included at a later date. Several potentially serious problems have been identified with methanol use. The most attractive solutions depend upon an integrated combination of vehicle modifications and fuel design. No vehicle problems were found which could not be solved with relatively minor developments of existing technology providing the methanol or blend fuel was itself engineered to ameliorate the solution. Research needs have been identified in the areas of lubrication and materials. These, while apparently solvable, must precede use of methanol or methanol-gasoline blends as motor fuels. Because of the substantial costs and complexities of a retrofitting program, use of methanol must be evaluated in relation to other petroleum-saving alternatives. Future vehicles can be designed initially to operate satisfactorily on these alternate fuels. However a specific fuel composition must be specified around which the future engines and vehicles can be designed.

  12. Fossil fuels -- future fuels

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Fossil fuels -- coal, oil, and natural gas -- built America`s historic economic strength. Today, coal supplies more than 55% of the electricity, oil more than 97% of the transportation needs, and natural gas 24% of the primary energy used in the US. Even taking into account increased use of renewable fuels and vastly improved powerplant efficiencies, 90% of national energy needs will still be met by fossil fuels in 2020. If advanced technologies that boost efficiency and environmental performance can be successfully developed and deployed, the US can continue to depend upon its rich resources of fossil fuels.

  13. UC Davis Fuel Cell, Hydrogen, and Hybrid Vehicle (FCH2V) GATE Center of Excellence

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, Paul

    2012-05-31

    This is the final report of the UC Davis Fuel Cell, Hydrogen, and Hybrid Vehicle (FCH2V) GATE Center of Excellence which spanned from 2005-2012. The U.S. Department of Energy (DOE) established the Graduate Automotive Technology Education (GATE) Program, to provide a new generation of engineers and scientists with knowledge and skills to create advanced automotive technologies. The UC Davis Fuel Cell, Hydrogen, and Hybrid Vehicle (FCH2V) GATE Center of Excellence established in 2005 is focused on research, education, industrial collaboration and outreach within automotive technology. UC Davis has had two independent GATE centers with separate well-defined objectives and research programs from 1998. The Fuel Cell Center, administered by ITS-Davis, has focused on fuel cell technology. The Hybrid-Electric Vehicle Design Center (HEV Center), administered by the Department of Mechanical and Aeronautical Engineering, has focused on the development of plug-in hybrid technology using internal combustion engines. The merger of these two centers in 2005 has broadened the scope of research and lead to higher visibility of the activity. UC Davis's existing GATE centers have become the campus's research focal points on fuel cells and hybrid-electric vehicles, and the home for graduate students who are studying advanced automotive technologies. The centers have been highly successful in attracting, training, and placing top-notch students into fuel cell and hybrid programs in both industry and government.

  14. Sliding mode observers for automotive alternator

    Science.gov (United States)

    Chen, De-Shiou

    Estimator development for synchronous rectification of the automotive alternator is a desirable approach for estimating alternator's back electromotive forces (EMFs) without a direct mechanical sensor of the rotor position. Recent theoretical studies show that estimation of the back EMF may be observed based on system's phase current model by sensing electrical variables (AC phase currents and DC bus voltage) of the synchronous rectifier. Observer design of the back EMF estimation has been developed for constant engine speed. In this work, we are interested in nonlinear observer design of the back EMF estimation for the real case of variable engine speed. Initial back EMF estimate can be obtained from a first-order sliding mode observer (SMO) based on the phase current model. A fourth-order nonlinear asymptotic observer (NAO), complemented by the dynamics of the back EMF with time-varying frequency and amplitude, is then incorporated into the observer design for chattering reduction. Since the cost of required phase current sensors may be prohibitive, the most applicable approach in real implementation by measuring DC current of the synchronous rectifier is carried out in the dissertation. It is shown that the DC link current consists of sequential "windows" with partial information of the phase currents, hence, the cascaded NAO is responsible not only for the purpose of chattering reduction but also for necessarily accomplishing the process of estimation. Stability analyses of the proposed estimators are considered for most linear and time-varying cases. The stability of the NAO without speed information is substantiated by both numerical and experimental results. Prospective estimation algorithms for the case of battery current measurements are investigated. Theoretical study indicates that the convergence of the proposed LAO may be provided by high gain inputs. Since the order of the LAO/NAO for the battery current case is one order higher than that of the link

  15. Fuel assemblies

    International Nuclear Information System (INIS)

    Mukai, Hideyuki

    1987-01-01

    Purpose: To prevent bending of fuel rods caused by the difference of irradiation growth between coupling fuel rods and standards fuel rods thereby maintain the fuel rod integrity. Constitution: The f value for a fuel can (the ratio of pole of zirconium crystals in the entire crystals along the axial direction of the fuel can) of a coupling fuel rod secured by upper and lower tie plates is made smaller than the f value for the fuel can of a standard fuel rod not secured by the upper and the lower tie plates. This can make the irradiation growth of the fuel can of the coupling fuel rod greater than the irradiation growth of the fuel can of the standard fuel rod and, accordingly, since the elongation of the standard fuel rod can always by made greater, bending of the standard fuel rod can be prevented. (Yoshihara, M.)

  16. Development of a high-temperature durable catalyst for use in catalytic combustors for advanced automotive gas turbine engines

    Science.gov (United States)

    Tong, H.; Snow, G. C.; Chu, E. K.; Chang, R. L. S.; Angwin, M. J.; Pessagno, S. L.

    1981-01-01

    Durable catalytic reactors for advanced gas turbine engines were developed. Objectives were: to evaluate furnace aging as a cost effective catalytic reactor screening test, measure reactor degradation as a function of furnace aging, demonstrate 1,000 hours of combustion durability, and define a catalytic reactor system with a high probability of successful integration into an automotive gas turbine engine. Fourteen different catalytic reactor concepts were evaluated, leading to the selection of one for a durability combustion test with diesel fuel for combustion conditions. Eight additional catalytic reactors were evaluated and one of these was successfully combustion tested on propane fuel. This durability reactor used graded cell honeycombs and a combination of noble metal and metal oxide catalysts. The reactor was catalytically active and structurally sound at the end of the durability test.

  17. The Effect of Industrial Work Performance Practice and Performance Automotive Electrical Prakti entrepreneurial n Against Interests Automotive Mechanics Class XII Smk Diponegoro Depok Sleman

    OpenAIRE

    Arif Mustofa; Pairun Roniwijaya

    2013-01-01

    The purpose of this study was to determine (1) the influence of the industrial working practices achievement entrepreneurial interests, (2) the effect of automotive electrical practice achievement against entrepreneurial interests, and (3) influence of achievement and accomplishment industry work practices automotive electrical practices to entrepreneurial interest Automotive Mechanics XII class students of SMK Diponegoro Depok Sleman school year 2012/2013.  The results showed that the test r...

  18. Minimizing of the boundary friction coefficient in automotive engines using Al{sub 2}O{sub 3} and TiO{sub 2} nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Mohamed Kamal Ahmed, E-mail: eng.m.kamal@mu.edu.eg; Xianjun, Hou, E-mail: houxj@whut.edu.cn; Elagouz, Ahmed [Wuhan University of Technology, Hubei Key Laboratory of Advanced Technology for Automotive Components (China); Essa, F.A. [Kafrelsheikh University, Mechanical Engineering Department, Faculty of Engineering (Egypt); Abdelkareem, Mohamed A. A. [Wuhan University of Technology, Hubei Key Laboratory of Advanced Technology for Automotive Components (China)

    2016-12-15

    Minimizing of the boundary friction coefficient is critical for engine efficiency improvement. It is known that the tribological behavior has a major role in controlling the performance of automotive engines in terms of the fuel consumption. The purpose of this research is an experimental study to minimize the boundary friction coefficient via nano-lubricant additives. The tribological characteristics of Al{sub 2}O{sub 3} and TiO{sub 2} nano-lubricants were evaluated under reciprocating test conditions to simulate a piston ring/cylinder liner interface in automotive engines. The nanoparticles were suspended in a commercially available lubricant in a concentration of 0.25 wt.% to formulate the nano-lubricants. The Al{sub 2}O{sub 3} and TiO{sub 2} nanoparticles had sizes of 8–12 and 10 nm, respectively. The experimental results have shown that the boundary friction coefficient reduced by 35–51% near the top and bottom dead center of the stroke (TDC and BDC) for the Al{sub 2}O{sub 3} and TiO{sub 2} nano-lubricants, respectively. The anti-wear mechanism was generated via the formation of protective films on the worn surfaces of the ring and liner. These results will be a promising approach for improving fuel economy in automotive.

  19. Multifunctional Converter Drive for Automotive Electric Power Steering Systems

    NARCIS (Netherlands)

    Hackner, T.J.

    2013-01-01

    In this thesis it is shown that in the case of an automotive electric power steering system, critical pulse power loads can be decoupled from the power net with a storage element and a multifunctional converter. A multifunctional converter system is proposed because it uses the motor drive system as

  20. Automotive Manufacturing Assessment System : Volume 1. Master Product Schedules.

    Science.gov (United States)

    1999-11-01

    Volume I is part of a four volume set documenting areas of research resulting from the development of the Automotive Manufacturing Assessment System (AMAS) for the DOT/Transportation Systems Center. AMAS was designed to assist in the evaluation of in...

  1. Engine Fundamentals: Automotive Mechanics Instructional Program. Block 2.

    Science.gov (United States)

    O'Brien, Ralph D.

    The second of six instructional blocks in automotive mechanics, the lessons and supportive information in the document provide a guide for teachers in planning an instructional program in engine fundamentals at the secondary and postsecondary level. The material, as organized, is a suggested sequence of instruction within each block. Each lesson…

  2. Laser surface treatment of grey cast iron for automotive applications

    NARCIS (Netherlands)

    Ocelik, V.; Tang, P.N.; de Boer, M.C.; de Oliveira, U.; de Hosson, J.T.M.; DeHosson, JTM; Brebbia, CA; Nishida, SI

    2005-01-01

    The surface of pearlitic grey cast iron was treated using a 2 kW Nd:YAG laser beam with the final aim to improve its surface properties, mainly for automotive applications. Two kinds of laser surface treatments were experimentally applied. In the laser surface hardening approach the surface of cast

  3. Designing Competency-Based Materials for the Automotive Mechanics Curriculum

    Science.gov (United States)

    Richardson, Roger L.

    1977-01-01

    Describes the Career Education Center's (Florida State University) development of the "Automotive Mechanics Catalog" (a job inventory noting performance objectives for specific occupational programs), using the Vocational-Technical Education Consortium of States (V-TECS) model. Also describes the development of curriculum materials using…

  4. Automotive Technology Student Learning Styles and Their Implications for Faculty

    Science.gov (United States)

    Threeton, Mark D.; Walter, Richard A.

    2009-01-01

    In an effort to provide Career and Technical Education (CTE) professionals with additional insight on how to better meet the educational needs of the learner, this study sought to identify the preference for learning of postsecondary automotive technology students. While it might appear logical to naturally classify auto-tech students as primarily…

  5. Competency-Based Materials for the Florida Automotive Mechanics Curriculum

    Science.gov (United States)

    Goodson, Ludy; And Others

    1978-01-01

    Describes Florida's new automotive mechanics curriculum, an individualized, self-paced learning sequence that combines text material, review exercises and actual work activities. Development of the materials, including incorporation of Florida's V-TECS catalog of performance objectives in auto mechanics, is described. A field-test experience of a…

  6. Automotive HMI design and participatory user involvement: review and perspectives.

    Science.gov (United States)

    François, Mathilde; Osiurak, François; Fort, Alexandra; Crave, Philippe; Navarro, Jordan

    2017-04-01

    Automotive human-machine interface (HMI) design is facing new challenges due to the technological advances of the last decades. The design process has to be adapted in order to address human factors and road safety challenges. It is now widely accepted that user involvement in the HMI design process is valuable. However, the current form of user involvement in industry remains at the stages of concept assessment and usability tests. Moreover, the literature in other fields (e.g. information systems) promotes a broader user involvement with participatory design (i.e. the user is fully involved in the development process). This article reviews the established benefits of participatory design and reveals perspectives for automotive HMI quality improvement in a cognitive ergonomic framework. Practitioner Summary: Automotive HMI quality determines, in part, drivers' ability to perform primary driving tasks while using in-vehicle devices. User involvement in the design process is a key point to contribute to HMI quality. This article reports the potential benefits of a broad involvement from drivers to meet automotive HMI design challenges.

  7. Analysis of reconfigurable assembly system framing systems in automotive industry

    Directory of Open Access Journals (Sweden)

    Md Zain Mohamad Zamri

    2017-01-01

    Full Text Available Current trend in automotive industry shows increasing demand for multiple models with lean production. Prior to that, automotive manufacturing systems evolved from mass production to flexible automation. Material handling systems and equipment in a single assembly line with multiple models require high investment but with low throughput thus making production cost relatively high. Current assembly process of side structure and undercarriage with downtime occurrence during assembly process affecting production performance (quality, cost and delivery. Manufacturing facilities should allow more flexibility and increase intelligence evolving toward novel reconfigurable assembly systems (RAS. RAS is envisaged capable of increasing factor flexibility and responsiveness by incorporating assembly jig, robot and framing, which could be next generation of world class automotive assembly systems. This project research proposes a new methodology of framework reconfigurable assembly systems principles in automotive framing systems i.e. enhance assembly process between side structure assembly and undercarriage assembly which a new RAS is capable to reconfigure the assembly processes of multiple model on a single assembly line. Simulation software (Witness will be used to simulate and validate current and proposed assembly process. RAS is expected to be a solution for rapid change in structure and for a responsively adjustable production capacity. Quality, cost and delivery are production key parameters that can be achieved by implementing RAS.

  8. Big data in automotive production - concepts and experiences

    OpenAIRE

    Bauernhansl, Thomas

    2016-01-01

    The presentation "Big Data in Automotive Production - Concepts and Experiences" deals with the following aspects: - The Digital World ofToday and Tomorrow - Change of Product Architecture - Elements of the Fourth Industrial Revolution - Everything as a Service (XaaS) - Big Data - Overview - Big Data in Production − Examples

  9. Service Station Attendant and Light Automotive Maintenance, Course Description.

    Science.gov (United States)

    Clifford, Jack W.; And Others

    Prepared by instructors and curriculum specialists, this course of study was designed to meet the individual needs of the dropout and/or hard-core unemployed youth by providing training as a service station attendant and light automotive maintenance mechanic. The achievement level of each student is determined at entry, and small instructional…

  10. Visual bias in subjective assessments of automotive sounds

    DEFF Research Database (Denmark)

    Ellermeier, Wolfgang; Legarth, Søren Vase

    2006-01-01

    In order to evaluate how strong the influence of visual input on sound quality evaluation may be, a naive sample of 20 participants was asked to judge interior automotive sound recordings while simultaneously being exposed to pictures of cars. twenty-two recordings of second-gear acceleration...

  11. Estimation of Kinetic Parameters in an Automotive SCR Catalyst Model

    DEFF Research Database (Denmark)

    Åberg, Andreas; Widd, Anders; Abildskov, Jens

    2016-01-01

    A challenge during the development of models for simulation of the automotive Selective Catalytic Reduction catalyst is the parameter estimation of the kinetic parameters, which can be time consuming and problematic. The parameter estimation is often carried out on small-scale reactor tests...

  12. State Estimation in the Automotive SCR DeNOx Process

    DEFF Research Database (Denmark)

    Zhou, Guofeng; Jørgensen, John Bagterp; Duwig, Christophe

    2012-01-01

    Selective catalytic reduction (SCR) of nitrogen oxides (NOx) is a widely applied diesel engine exhaust gas after-treatment technology. For effective NOx removal in a transient operating automotive application, controlled dosing of urea can be used to meet the increasingly restrictive legislations...

  13. Examples on cold forged aluminium components in automotive industry

    DEFF Research Database (Denmark)

    Bay, Niels; Kolsgaard, A.

    2000-01-01

    The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken ...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

  14. Dynamic design of automotive systems: Engine mounts and ...

    Indian Academy of Sciences (India)

    Abstract. Dynamic design and vibro-acoustic modelling issues for automotive structures are illustrated via two case studies. The first case examines the role performance of passive and adaptive hydraulic engine mounts. In the second, the importance of welded joints and adhesives in vehicle bodies and chassis structures is ...

  15. Monitoring active filters under automotive aging scenarios with embedded instrument

    NARCIS (Netherlands)

    Wan, J.; Kerkhoff, Hans G.

    2012-01-01

    In automotive mixed-signal SoCs, the analogue/mixed-signal front-ends are of particular interest with regard to dependability. Because of the many electrical disturbances at the front-end, often (active) filters are being used. Due to the harsh environments, in some cases, degradation of these

  16. Environmental Performance and firm strategies in the Dutch automotive sector

    NARCIS (Netherlands)

    van der Vooren, A.; Alkemade, F.; Hekkert, M.P.

    2013-01-01

    This paper explores how automotive firms positioned their portfolio since the introduction of energy labels for cars. Using data on product characteristics of automobiles offered on the Dutch market over the period 2001-2010, we analyse how car manufacturers' product portfolios have changed.

  17. Product waste in the automotive industry : Technology and environmental management

    NARCIS (Netherlands)

    Groenewegen, Peter; Hond, Frank Den

    1993-01-01

    In this article the changes in technology and industry structure forced by waste management in the automotive industry are explored. The analysis is based on (1) a characterisation of corporate response to environmental issues, and (2) the management of technology applied to the car manufacturing

  18. Utilization of Durability Criterion to Develop Automotive Components

    DEFF Research Database (Denmark)

    Ricardo, Luiz Carlos Hernandes

    2010-01-01

    Today the automotive companies must reduce the time to development of new products with improvement in performance, durability and low cost reductions where possible. To achieve this goal the carmakers need to improve the design criterion of car systems like body, chassis and suspension component...

  19. Flexible labour strategy in the Dutch automotive industry

    NARCIS (Netherlands)

    van Riemsdijk, Maarten; de Leede, Jan

    2001-01-01

    Labour flexibility is a major way for companies to become more flexible. Why companies use flexible labour relations varies widely per industry. We assess the development of labour flexibility within the Dutch automotive industry. Four cases, together representing the production chain, are

  20. Developing E-Learning Solutions in the Automotive Industry

    Science.gov (United States)

    Bogdan, Razvan; Ancusa, Versavia

    2016-01-01

    In the rapid developing market of automotive industry, cutting-edge technologies are being introduced. One such example is the AUTOSAR standard. Companies are investing a large amount of finances for the training of their employees into the intricacies of such technologies. In order to face such an increase of the training costs, automotive…

  1. Events as spaces for upgrading : Automotive events in Shanghai

    NARCIS (Netherlands)

    E. van Tuijl (Erwin); K. Dittrich (Koen)

    2015-01-01

    textabstractThis study contributes to the literature dealing with upgrading of the Chinese automotive industry by analysing the role of events in the upgrading process. By combining literature on temporary clusters with that of knowledge sourcing and upgrading, we investigate how firms use events

  2. Performance of Automotive SLI Battery under Constant Current ...

    African Journals Online (AJOL)

    In this project, a cost-effective 12V battery charge controller was developed to implement constant current constant voltage charge algorithm in small-sized stand-alone solar PV systems. The algorithm was tested on automotive SLI battery instead of deep-cycle PV battery to further reduce overall system cost. The battery ...

  3. 76 FR 40591 - Coordinating Policies on Automotive Communities and Workers

    Science.gov (United States)

    2011-07-11

    ... vested in me as President by the Constitution and the laws of the United States of America, it is hereby... that include land-use redevelopment, small business support, and worker training. The purpose of this... Federal policies and programs intended to address issues of special importance to automotive communities...

  4. Monitoring sealed automotive lead-acid batteries by sparse ...

    Indian Academy of Sciences (India)

    A reliable diagnostics of lead-acid batteries would become mandatory with the induction of an improved power net and the increase of electrically assisted features in future automobiles. Sparse-impedance spectroscopic technique described in this paper estimates the internal resistance of sealed automotive lead-acid ...

  5. Analysis of lead content in automotive shredder residue (ASR)

    International Nuclear Information System (INIS)

    Gonzalez-Fernandez, Oscar; Pessanha, Sofia; Queralt, Ignacio; Carvalho, Maria Luisa

    2009-01-01

    Automotive shredder residue (ASR) is a very heterogeneous waste, which could have a very high metal content on finest fractions φ -1 in the fraction -1 in the fraction between 2 and 6 mm) and that such type of instrumentation enables a fast measurement with a limit of detection of 1.1 mg kg -1 for 1000 s measurement).

  6. Sensor fault diagnosis for automotive engines with real data ...

    African Journals Online (AJOL)

    In this paper, a new fault diagnosis method using an adaptive neural network for automotive engines is developed. A redial basis function (RBF) network is used as a fault classifier with its widths and weights on-line adapted to cope with model uncertainty and time varying dynamics caused by mechanical wear of engine ...

  7. Monitoring sealed automotive lead-acid batteries by sparse ...

    Indian Academy of Sciences (India)

    Sparse-impedance spectroscopic technique described in this paper estimates the internal resistance of sealed automotive lead-acid batteries in the frequency range 10 Hz-10 kHz, usually produced by the alternators fitted in ... Solid State and Structural Chemistry Unit, Indian Institute of Science, Bangalore 560 012, India ...

  8. Potentials and limitations of alternative fuels for diesel engine

    Directory of Open Access Journals (Sweden)

    Gligorijević Radinko

    2009-01-01

    Full Text Available The primary energy consumption in the world has increased continuously. The most important primary energy source is oil. The supply of automotive fuels today is based almost entirely on oil, and the demand for liquid transportation fuels worldwide will rise significantly in the next fifty years. Growing energy consumption and decreasing fossil resources are reasons for increasing prices of fossil fuel. Besides limited availability, contribution to greenhouse effect and pollutant emission represent another problem of fossil fuel. Both of these problems can be overcome by increased application of renewable biofuels. Therefore, great effort is made to supplement the primary energy sources by including renewable energies. There are alternative fuels 1st and 2nd generation. Some of them show high potential for reduction of engine out emission. But there are economical and technical barriers when such fuels are applied. This paper shows both advantage and disadvantage of alternative fuels, especially when used for diesel engines.

  9. The Partnership for Today That Works for Tomorrow: The Professional Automotive Training Center at Shoreline Community College.

    Science.gov (United States)

    Hightower, Cameron

    The Professional Automotive Training Center (PATC) is a 28,150 square foot automotive technician training center located on the campus of Shoreline Community College (SCC) in Washington. The complex is the result of a partnership between SCC and the 230 automotive dealerships of the Puget Sound Automotive Dealers Association and is designed to…

  10. Mississippi Curriculum Framework for Automotive Mechanics (Program CIP: 47.0604--Auto/Automotive Mechanic/Tech). Secondary Programs.

    Science.gov (United States)

    Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

    This document, which reflects Mississippi's statutory requirement that instructional programs be based on core curricula and performance-based assessment, contains outlines of the instructional units required in local instructional management plans and daily lesson plans for automotive mechanics I and II. Presented first are a program description…

  11. Profiles of Major Suppliers to the Automotive Industry : Vol. 3. Plastics, Glass and Fiberglass Suppliers to the Automotive Industry

    Science.gov (United States)

    1982-08-01

    This study summarizes extensive information collected over a two-year period (October 1978 to 1980) on suppliers of parts and components, materials, and machine tools to the automotive industry in the United States. The objective of the study was to ...

  12. Power Modulation Investigation for High Temperature (175-200 degrees Celcius) Automotive Application

    Energy Technology Data Exchange (ETDEWEB)

    McCluskey, F. P.

    2007-04-30

    Hybrid electric vehicles were re-introduced in the late 1990s after a century dominated by purely internal combustion powered engines[1]. Automotive players, such as GM, Ford, DaimlerChrysler, Honda, and Toyota, together with major energy producers, such as BPAmoco, were the major force in the development of hybrid electric vehicles. Most notable was the development by Toyota of its Prius, which was launched in Japan in 1997 and worldwide in 2001. The shift to hybrids was driven by the fact that the sheer volume of vehicles on the road had begun to tax the ability of the environment to withstand the pollution of the internal combustion engine and the ability of the fossil fuel industry to produce a sufficient amount of refined gasoline. In addition, the number of vehicles was anticipated to rise exponentially with the increasing affluence of China and India. Over the last fifteen years, major advances have been made in all the technologies essential to hybrid vehicle success, including batteries, motors, power control and conditioning electronics, regenerative braking, and power sources, including fuel cells. Current hybrid electric vehicles are gasoline internal combustion--electric motor hybrids. These hybrid electric vehicles range from micro-hybrids, where a stop/start system cuts the engine while the vehicle is stopped, and mild hybrids where the stop/start system is supplemented by regenerative braking and power assist, to full hybrids where the combustion motor is optimized for electric power production, and there is full electric drive and full regenerative braking. PSA Peugeot Citroen estimates the increased energy efficiency will range from 3-6% for the micro-hybrids to 15-25% for the full hybrids.[2] Gasoline-electric hybrids are preferred in US because they permit long distance travel with low emissions and high gasoline mileage, while still using the existing refueling infrastructure. One of the most critical areas in which technology has been

  13. The influence of surface topography on the forming friction of automotive aluminum sheet

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, Pamela Ann [Univ. of California, Berkeley, CA (United States). Dept. of Materials Science and Mineral Engineering

    1998-05-01

    Interest in utilizing aluminum alloys in automobiles has increased in recent years as a result of the desire to lower automobile weight and, consequently, increase fuel economy. While aluminum alloy use in cast parts has increased, outer body panel applications are still being investigated. The industry is interested in improving the formability of these sheet alloys by a combination of alloy design and processing. A different avenue of improving the formability of these alloys may be through patterning of the sheet surface. Surface patterns hold the lubricant during the forming process, with a resulting decrease in the sheet-die surface contact. While it has been speculated that an optimum surface pattern would consist of discrete cavities, detailed investigation into the reduction of forming friction by utilizing discrete patterns is lacking. A series of discrete patterns were investigated to determine the dependence of the forming friction of automotive aluminum alloys on pattern lubricant carrying capacity and on material strength. Automotive aluminum alloys used in outer body panel applications were rolled on experimental rolls that had been prepared with a variety of discrete patterns. All patterns for each alloy were characterized before and after testing both optically and, to determine pattern lubricant capacity, using three dimensional laser profilometry. A draw bead simulation (DBS) friction tester was designed and fabricated to determine the forming friction of the patterned sheets. Tensile testing and frictionless DBS testing were performed to ascertain the material properties of each sheet. The most striking result of this work was the inversely linear dependence of forming friction on the lubricant carrying capacity of the discrete patterns.

  14. Cold start dynamics and temperature sliding observer design of an automotive SOFC APU

    Science.gov (United States)

    Lin, Po-Hsu; Hong, Che-Wun

    This paper presents a dynamic model for studying the cold start dynamics and observer design of an auxiliary power unit (APU) for automotive applications. The APU is embedded with a solid oxide fuel cell (SOFC) stack which is a quiet and pollutant-free electric generator; however, it suffers from slow start problem from ambient conditions. The SOFC APU system equips with an after-burner to accelerate the start-up transient in this research. The combustion chamber burns the residual fuel (and air) left from the SOFC to raise the exhaust temperature to preheat the SOFC stack through an energy recovery unit. Since thermal effect is the dominant factor that influences the SOFC transient and steady performance, a nonlinear real-time sliding observer for stack temperature was implemented into the system dynamics to monitor the temperature variation for future controller design. The simulation results show that a 100 W APU system in this research takes about 2 min (in theory) for start-up without considering the thermal limitation of the cell fracture.

  15. Fuel additives: keys to quality, distribution, and performance

    Energy Technology Data Exchange (ETDEWEB)

    Tupa, R.C.; Dorer, C.J.

    1985-10-01

    The performance and formulations of some additives currently used to improve gasoline and diesel fuel are examined. Fuel additives are characterized according to purposes. Trace metal compounds are examined as powerful catalysts for gasoline oxidation. Frequent sources for such contamination are described: copper-containing alloys in refinery equipment, product distribution systems, chemicals used in refining, and automotive fuel systems. Discussions are presented on how to minimize copper's effect by transforming the copper compound into another which has no pro-oxidant behavior.

  16. Engines, fuels and pollution

    International Nuclear Information System (INIS)

    Salvi, G.

    1992-01-01

    The article points out the close relationship among engines, fuels and polluting emissions, and outlines an overall picture of future trends. The technical trade literature shows that diesel engines may undergo strong future development, due to their more favourable energy converting and less polluting characteristics. With regard to petrol injection engines, their improved construction under extremely close tolerances will result in a severe tightening-up of fuel specifications (with or without lead), so as to prevent the deposition of residues at the inlet (manifolds, injectors, valves, and combustion chamber), and their ensuing adverse effects on vehicle handling especially during the 'warm-up' stage. Recent checkups and tests run in the USA have evidenced that automotive engine-derived pollution in towns is in fact considerably more severe than that derived from mathematical models based on 'average emission factors' determined on a laboratory scale (roller bench tests, vaporization tests etc.). The entire body of regulations issued so far becomes questionable, and supplementary studies based on road-tests have been proposed. The paper's discussion is concluded with statistical data showing traffic pollution caused by VOCs (volatile organic compounds)

  17. Breaking down the barriers to commercialization of fuel cells in transportation through Government - industry R&D programs

    Energy Technology Data Exchange (ETDEWEB)

    Chalk, S.G. [Dept. of Energy, Washington, DC (United States); Venkateswaran, S.R. [Energetics, Inc., Columbia, MD (United States)

    1996-12-31

    PEM fuel cell technology is rapidly emerging as a viable propulsion alternative to the internal combustion engine. Fuel cells offer the advantages of low emissions, high efficiency, fuel flexibility, quiet and continuous operation, and modularity. Over the last decade, dramatic advances have been achieved in the performance and cost of PEM fuel cell technologies for automotive applications. However, significant technical barriers remain to making fuel cell propulsion systems viable alternatives to the internal combustion engine. This paper focuses on the progress achieved and remaining technical barriers while highlighting Government-industry R&D efforts that are accelerating fuel cell technology toward commercialization.

  18. Alternative Fuels

    Science.gov (United States)

    Alternative fuels include gaseous fuels such as hydrogen, natural gas, and propane; alcohols such as ethanol, methanol, and butanol; vegetable and waste-derived oils; and electricity. Overview of alternative fuels is here.

  19. A Development Curriculum Plan To Achieve a Sequenced Curriculum between High School Courses in Automotive Mechanics and the Mattatuck Community College Automotive Technician Program. Final Report.

    Science.gov (United States)

    Mattatuck Community Coll., Waterbury, CT.

    This document contains a developmental curriculum plan for an articulated curriculum in automotive mechanics for Connecticut's Mattatuck Community College and area high schools. The curriculum guide includes a course description, criteria for evaluation, attendance policy, objectives, a curriculum outline, a three-part automotive technician test,…

  20. State Articulated Instructional Objectives Guide for Occupational Education Programs. State Pilot Model for Automotive Mechanics (DCC V-003) and Automotive Mechanics (High School).

    Science.gov (United States)

    North Carolina State Dept. of Community Colleges, Raleigh.

    This articulation instructional objective guide for automotive mechanics contains summary information on fifteen blocks (courses) of instruction. They are introduction to automotive technology; lubrication and vehicle operating maintenance; cooling system maintenance and repair; automobile heater maintenance and repair; braking system maintenance…

  1. Fuel distribution logistics in Brazil: technical and economic aspects; Aspectos tecnico-economicos da logistica da distribuicao de combustiveis no Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Esteves, Heloisa Borges B.; Bicalho, Lucia N. [Agencia Nacional do Petroleo, Gas Natural e Biocombustiveis (ANP), Rio de Janeiro, RJ (Brazil)

    2008-07-01

    In Brazil, there are around 250 companies operating in the automotive fuel distribution segment, responsible for the automotive fuels wholesale commercialization activity. Those companies supply not only gas stations, but also final consumers and TRR's. Their clients are distributed regionally, which requires flexibility and the ability to supply clients efficiently at the smaller possible cost, transforming variables such as the transportation alternatives adopted, the location of the storage facilities and its correct dimension on key decisions. This paper analyses the general scenario of the fuels distribution logistics in Brazil from a economic perspective, and its impacts on the companies competitive strategies. (author)

  2. PEM fuel cell geometry optimisation using mathematical modeling

    Directory of Open Access Journals (Sweden)

    E Carcadea

    2008-09-01

    Full Text Available There have been extensive efforts devoted to proton exchangemembrane (PEM fuel cell modeling and simulations to study fuel cellperformance. Although fuel cells have been successfully demonstrated inboth automotive and stationary power applications, there are numeroustechnical and logistic issues that still have to be solved, such asperformance, cost, and system issues. A model based on steady,isothermal, electrochemical, three-dimensional computational fluiddynamics using the FLUENT CFD software package has been developedto predict the fluid flow pattern within a PEMFC. Three types of flow field areinvestigated with serpentine, parallel or spiral channels in order todetermine the best configuration for the fuel cell performance. In thiscontext, the paper presents the results that we have obtained and, as aconclusion of the simulations, we have achieved the best configurationregarding the performance for the fuel cell with serpentine channels. Weconsider the mathematical and computational modeling as an importantalternative for fuel cell optimization and for the exploitation/experimentationin cost reduction.

  3. Joining of Dissimilar alloy Sheets (Al 6063&AISI 304 during Resistance Spot Welding Process: A Feasibility Study for Automotive industry

    Directory of Open Access Journals (Sweden)

    Reddy Sreenivasulu

    2014-12-01

    Full Text Available Present design trends in automotive manufacture have shifted emphasis to alternative lightweight materials in order to achieve higher fuel efficiency and to bring down vehicle emission. Although some other joining techniques are more and more being used, spot welding still remains the primary joining method in automobile manufacturing so far. Spot welds for automotive applications should have a sufficiently large diameter, so that nugget pullout mode is the dominant failure mode. Interfacial mode is unacceptable due to its low load carrying and energy absorption capability. Strength tests with different static loading were performed in, to reveal the failure mechanisms for the lap-shear geometry and the cross-tension geometry. Based on the literature survey performed, venture into this work was amply motivated by the fact that a little research work has been conducted to joining of dissimilar materials like non ferrous to ferrous. Most of the research works concentrated on joining of different materials like steel to steel or aluminium alloy to aluminium alloy by resistance spot welding. In this work, an experimental study on the resistance spot weldability of aluminium alloy (Al 6063 and austenitic stainless steel (AISI304 sheets, which are lap joined by using a pedestal type resistance spot welding machine. Welding was conducted using a 45-deg truncated cone copper electrode with 10-mm face diameter. The weld nugget diameter, force estimation under lap shear test and T – peel test were investigated using digital type tensometer attached with capacitive displacement transducer (Mikrotech, Bangalore, Model: METM2000ER1. The results shows that joining of Al 6063 and AISI 304 thin sheets by RSW method are feasible for automotive structural joints where the loads are below 1000N act on them, it is observed that by increasing the spots per unit length, then the joint with standing strength to oppose failure is also increased linearly incase of

  4. Fuel assembly

    International Nuclear Information System (INIS)

    Chaki, Masao; Nishida, Koji; Karasawa, Hidetoshi; Kanazawa, Toru; Orii, Akihito; Nagayoshi, Takuji; Kashiwai, Shin-ichi; Masuhara, Yasuhiro

    1998-01-01

    The present invention concerns a fuel assembly, for a BWR type nuclear reactor, comprising fuel rods in 9 x 9 matrix. The inner width of the channel box is about 132mm and the length of the fuel rods which are not short fuel rods is about 4m. Two water rods having a circular cross section are arranged on a diagonal line in a portion of 3 x 3 matrix at the center of the fuel assembly, and two fuel rods are disposed at vacant spaces, and the number of fuel rods is 74. Eight fuel rods are determined as short fuel rods among 74 fuel rods. Assuming the fuel inventory in the short fuel rod as X(kg), and the fuel inventory in the fuel rods other than the short fuel rods as Y(kg), X and Y satisfy the relation: X + Y ≥ 173m, Y ≤ - 9.7X + 292, Y ≤ - 0.3X + 203 and X > 0. Then, even when the short fuel rods are used, the fuel inventory is increased and fuel economy can be improved. (I.N.)

  5. Fuel cells

    Science.gov (United States)

    Hooie, D. T.; Harrington, B. C., III; Mayfield, M. J.; Parsons, E. L.

    1992-07-01

    The primary objective of DOE's Fossil Energy Fuel Cell program is to fund the development of key fuel cell technologies in a manner that maximizes private sector participation and in a way that will give contractors the opportunity for a competitive posture, early market entry, and long-term market growth. This summary includes an overview of the Fuel Cell program, an elementary explanation of how fuel cells operate, and a synopsis of the three major fuel cell technologies sponsored by the DOE/Fossil Energy Phosphoric Acid Fuel Cell program, the Molten Carbonate Fuel Cell program, and the Solid Oxide Fuel Cell program.

  6. Fuel assembly

    International Nuclear Information System (INIS)

    Yamazaki, Hajime.

    1995-01-01

    In a fuel assembly having fuel rods of different length, fuel pellets of mixed oxides of uranium and plutonium are loaded to a short fuel rod. The volume ratio of a pellet-loaded portion to a plenum portion of the short fuel rod is made greater than the volume ratio of a fuel rod to which uranium fuel pellets are loaded. In addition, the volume of the plenum portion of the short fuel rod is set greater depending on the plutonium content in the loaded fuel pellets. MOX fuel pellets are loaded on the short fuel rods having a greater degree of freedom relevant to the setting for the volume of the plenum portion compared with that of a long rod fuel, and the volume of the plenum portion is ensured greater depending on the plutonium content. Even if a large amount of FP gas and He gas are discharged from the MOX fuels compared with that from the uranium fuels, the internal pressure of the MOX fuel rod during operation is maintained substantially identical with that of the uranium fuel rod, so that a risk of generating excess stresses applied to the fuel cladding tubes and rupture of fuels are greatly reduced. (N.H.)

  7. Impact of novel thermoelectric materials on automotive applications

    Science.gov (United States)

    Brignone, Mauro; Ziggiotti, Alessandro

    2012-06-01

    Despite the fact that thermoelectric (TE) devices are compact, quiet, rugged, stable and very reliable, thermoelectrics have found only niche applications because they are also inefficient (less that 5% conversion efficiency is typical) and costly. The key to more widespread acceptance of thermoelectric is the development of materials that are capable of higher conversion efficiency, but other fundamental materials parameters play a role not less important to open to large applications and markets. In particular the automotive sector requires low materials density, materials made from widely-available pure elements with very large supply chains, non-toxicity of elements and potential compliance with REACH and RoHS obligations and low raw material cost combined with low manufacturing costs. The impact of novel TE materials on automotive application will be described focusing on promising nano magnesium silicide and skutterudites.

  8. REUSE OF AUTOMOTIVE COMPONENTS FROM DISMANTLED END OF LIFE VEHICLES

    Directory of Open Access Journals (Sweden)

    Piotr NOWAKOWSKI

    2013-12-01

    Full Text Available The problem of recycling end of life automotive vehicles is serious worldwide. It is one of the most important streams of waste in developed countries. It has big importance as recycling potential of raw materials content in automotive vehicles is valuable. Different parts and assemblies after dismantling can also be reused in vehicles where replacement of specific component is necessary. Reuse of the components should be taken into consideration in selecting the vehicles dismantling strategy. It also complies with European Union policy concerning end of life vehicles (ELV. In the paper it is presented systematic approach to dismantling strategies including disassembly oriented on further reuse of components. It is focused on decision making and possible benefits calculation from economic and environmental point of view.

  9. Case Study of Engineering Risk in Automotive Industry

    Science.gov (United States)

    Popa, Dan Mihai

    2018-03-01

    The primary objective of this paper is to show where the engineering of risk management is placed and how its implementation has been tried in multinational companies in automotive industry from Romania. A large number of companies don't use a strategy to avoid the engineering risk in their design products. The main reason is not because these companies haven't heard about standards for risk management such as ISO 31000; the problem is that the business units which were summed up, have just set up a risk list at the beginning of the project, without any follow up. The purpose of this article is to create an implementation risk tracking in automotive industry companies in Romania, due to a change request from customers according to supply companies within the quality process, in the research and development phase.

  10. Automotive Technology and Human Factors Research: Past, Present, and Future

    Directory of Open Access Journals (Sweden)

    Motoyuki Akamatsu

    2013-01-01

    Full Text Available This paper reviews the history of automotive technology development and human factors research, largely by decade, since the inception of the automobile. The human factors aspects were classified into primary driving task aspects (controls, displays, and visibility, driver workspace (seating and packaging, vibration, comfort, and climate, driver’s condition (fatigue and impairment, crash injury, advanced driver-assistance systems, external communication access, and driving behavior. For each era, the paper describes the SAE and ISO standards developed, the major organizations and conferences established, the major news stories affecting vehicle safety, and the general social context. The paper ends with a discussion of what can be learned from this historical review and the major issues to be addressed. A major contribution of this paper is more than 180 references that represent the foundation of automotive human factors, which should be considered core knowledge and should be familiar to those in the profession.

  11. 20th International Forum on Advanced Microsystems for Automotive Applications

    CERN Document Server

    Müller, Beate; Meyer, Gereon

    2016-01-01

    This book contains the papers presented at the 20th anniversary edition of the AMAA conference held in Brussels, Belgium in 2016. The theme of the conference was "Smart Systems for the Automobile of the Future". The automobile is currently being reshaped at unprecedented pace. Automation and electrification are the two dominant megatrends which dramatically change the choice and design of components, systems, vehicular architectures and ultimately the way we use cars in the coming decades. Novel E/E architectures, vehicular connectivity and cloud services will be key to extending the perception and decision-making horizons of automated vehicles, to enable cooperative functions and a seamless digital user experience. The AMAA's ongoing mission to detect novel trends in automotive ICT, electronics and smart systems and to discuss the technological implications is once again reflected in this volume. The book will be a valuable read for research experts and professionals in the automotive and smart systems indus...

  12. Integrated Computational Materials Engineering for Magnesium in Automotive Body Applications

    Science.gov (United States)

    Allison, John E.; Liu, Baicheng; Boyle, Kevin P.; Hector, Lou; McCune, Robert

    This paper provides an overview and progress report for an international collaborative project which aims to develop an ICME infrastructure for magnesium for use in automotive body applications. Quantitative processing-micro structure-property relationships are being developed for extruded Mg alloys, sheet-formed Mg alloys and high pressure die cast Mg alloys. These relationships are captured in computational models which are then linked with manufacturing process simulation and used to provide constitutive models for component performance analysis. The long term goal is to capture this information in efficient computational models and in a web-centered knowledge base. The work is being conducted at leading universities, national labs and industrial research facilities in the US, China and Canada. This project is sponsored by the U.S. Department of Energy, the U.S. Automotive Materials Partnership (USAMP), Chinese Ministry of Science and Technology (MOST) and Natural Resources Canada (NRCan).

  13. Pre-treatment processes for automotive applications in Europe

    Energy Technology Data Exchange (ETDEWEB)

    Schubach, P. [Oakite Products, Inc., Berkeley Heights, NJ (United States); Gehmecker, H. [Chemetall GmbH, Frankfurt am Main (Germany)

    1995-11-01

    Pre-treatment processes for automotive applications in Europe are optimized firstly due to the increasing use of aluminum and coated steel for car bodies and parts and secondly due to environmental issues. Prephosphated coated steel, mainly electrogalvanized steel with a trication zinc phosphate layer applied in the steel mill is used by many car manufacturers. Several R and D projects are under way to coat aluminum sheet with inorganic or organic layers to enhance forming, welding and joining properties. Environmental aspects initiated the development of cleaners with biodegradable and alkylphenolethoxylate-free surfactants, liquid grain refiners with longer bath life-time, nickel or nitrite-free zinc phosphate products and chrome-free passivations. All of these products are in use in many automotive body lines except the nickel-free phosphating process which is being tested in OEM parts lines. Details of the processes in a phosphating line are described including a section on phosphating of aluminum.

  14. Sustainability and Energy Efficiency in the Automotive Sector

    CERN Multimedia

    CERN. Geneva

    2013-01-01

    Since this year there can be no doubt that "sustainability" has become the top issue in the automotive sector. Volkswagen's CEO Prof. Dr. Martin Winterkorn attacked incumbents like BMW Group (so far the "most sustainable car manufacturer" for the 8th consecutive year) or Toyota (producer of the famous "Prius") head-on by boldly stating to become "the most profitable and most sustainable car manufacturer worldwide by 2018" . This announcement clearly shows that "sustainability" and "profitability" no longer are considered as conflicting targets. On the contrary, to Prof. Dr. Winterkorn : "climate protection is a driver for economic growth". To prime discussions, the plenary talk will give a brief overview of the entire range of energy efficiency in the automotive sector: based on the multiple drivers behind energy efficiency, practical examples are presented along the entire life-cycle of cars (R&D, production, usage and recycling). These "cases" include big automobile producers as well as their respectiv...

  15. Adverse effects of the automotive industry on carbon dioxide emissions

    Directory of Open Access Journals (Sweden)

    Mpho Bosupeng

    2016-05-01

    Full Text Available This study aims to determine the effects of the automotive industry on carbon dioxide emissions for the period from 1997 to 2010 for diverse economies, as well as the relationships between carbon dioxide discharges and output. The study applies cointegration and causality tests to validate these associations. The results of the Johansen cointegration test depict long-run associations between the quantity of passenger cars and carbon dioxide emissions in France, Sweden, Spain, Hungary and Japan. In addition, significant relations were observed between output and carbon dioxide discharges in Spain, Canada, India and Japan. Changes in output had substantial impact on emissions in Germany, Canada and India. The results also show that the number of passenger cars influences the magnitude of emissions in multiple economies. In conclusion, the automotive industry has to be considered in policies that aim to reduce carbon dioxide emissions.

  16. Development of nanolubricant automotive air conditioning (AAC test rig

    Directory of Open Access Journals (Sweden)

    Redhwan A.A.M.

    2017-01-01

    Full Text Available Nanolubricant been introduced in compressor might improve the performance of automotive air conditioning system. Prior testing of the nanolubricant enhancement performance, an automotive air conditioning (AAC system test rig base on compact car has to be developed; therefore this paper presented the development process of AAC test rig. There are 15 thermocouples, 2 pressure gauges and power analyzer were assembled on the system in order to analyse its performance. The experiment was conducted with four different charged of refrigerant. The charging was based on initial weight charged. At each quantity of refrigerant charge, performance of the AAC system was evaluated by determining three important parameters which is cooling capacity, compressor work and coefficient of performance (COP. The maximum average COP is achieved at 900 RPM is 7.07. The average and maximum COP enhancement of 7.07 % and 13.34 % were achieved by applying SiO2 nanolubricant inside the compressor.

  17. Mockup Didatic Set for Students Development in Automotive Electronic

    Directory of Open Access Journals (Sweden)

    Fabio Delatore

    2013-05-01

    Full Text Available The automotive engineering education area, specifically on internal combustion engine, requires the use of suitable systems, capable to simulate, test and obtain specifics data from its operation. Automotive engines are so complex due to it is a mix of engineering subjects, so, a mockup was created to help its study. The mockup is an exactly the same engine that equips a vehicle, but assembled in a mechanical base, equipped with all the necessary components for running it up. The objective of this work is to develop a mockup with a suitable Electronic Control Unit (ECU board, in order to obtain the sensors/actuators signals from the engine and control some important engine functions by using an external ECU, so that the students may test their own strategies, compare with the original ECU.

  18. 4th International Conference on Sustainable Automotive Technologies

    CERN Document Server

    Wellnitz, Jörg; Leary, Martin; Koopmans, Lucien

    2012-01-01

    The book on Sustainable Automotive Technologies aims to draw special attention to the research and practice focused on new technologies and approaches capable of meeting the challenges to sustainable mobility. In particular, the book features incremental and radical technical advancements that are able to meet social, economic and environmental targets in both local and global contexts. These include original solutions to the problems of pollution and congestion, vehicle and public safety, sustainable vehicle design and manufacture, new structures and materials, new power-train technologies and vehicle concepts. In addition to vehicle technologies, the book is also concerned with the broader systemic issues such as sustainable supply chain systems, integrated logistics and telematics, and end-of-life vehicle management. It captures selected peer reviewed papers accepted for presentation at the 4th International Conference on Sustainable Automotive Technologies, ICSAT2012, held at the RMIT, Melbourne, Australi...

  19. Making aerospace technology work for the automotive industry, introduction

    Science.gov (United States)

    Olson, W. T.

    1978-01-01

    NASA derived technology already in use in the automotive industry include: (1) developments in electronics design, computer systems, and quality control methods for line testing of cars and trucks; (2) a combustion analysis computer program for automotive engine research and development; (3) an infrared scanner and television display for analyzing tire design and performance, and for studying the effects of heat on the service life of V-belts, shock mounts, brakes, and rubber bearings; (4) exhaust gas analyzers for trouble shooting and emissions certification; (5) a device for reducing noise from trucks; and (6) a low cost test vehicle for measuring highway skid resistance. Services offered by NASA to facilitate access to its technology are described.

  20. Economic crisis and the automotive industry in Romania

    Directory of Open Access Journals (Sweden)

    Iosip, A.

    2010-12-01

    Full Text Available The economic crisis has affected many areas but the auto industry is perhaps one of the most affected. Renault, Ford, General Motors, Toyota, Volkswagen, BMW are just some of the big players caught unprepared. Through this paper we propose an analysis of the automotive market in Romania in order to understand the sales decrease of the last two years. At the same time we aimed at understanding the reasons that led to a decrease in car sales, what were the measures taken by the government to stop this phenomenon and how the economic crisis influenced the automotive field in Romania. An objective image of the situation in the automobile market in Romania at this moment also requires an analysis of the marketing environment and the changes it has undergone over time. Last but not least we will try to find a series of measures to re-launch the car market in Romania.

  1. The Quantitative Analysis of Chennai Automotive Industry Cluster

    Science.gov (United States)

    Bhaskaran, Ethirajan

    2016-07-01

    Chennai, also called as Detroit of India due to presence of Automotive Industry producing over 40 % of the India's vehicle and components. During 2001-2002, the Automotive Component Industries (ACI) in Ambattur, Thirumalizai and Thirumudivakkam Industrial Estate, Chennai has faced problems on infrastructure, technology, procurement, production and marketing. The objective is to study the Quantitative Performance of Chennai Automotive Industry Cluster before (2001-2002) and after the CDA (2008-2009). The methodology adopted is collection of primary data from 100 ACI using quantitative questionnaire and analyzing using Correlation Analysis (CA), Regression Analysis (RA), Friedman Test (FMT), and Kruskall Wallis Test (KWT).The CA computed for the different set of variables reveals that there is high degree of relationship between the variables studied. The RA models constructed establish the strong relationship between the dependent variable and a host of independent variables. The models proposed here reveal the approximate relationship in a closer form. KWT proves, there is no significant difference between three locations clusters with respect to: Net Profit, Production Cost, Marketing Costs, Procurement Costs and Gross Output. This supports that each location has contributed for development of automobile component cluster uniformly. The FMT proves, there is no significant difference between industrial units in respect of cost like Production, Infrastructure, Technology, Marketing and Net Profit. To conclude, the Automotive Industries have fully utilized the Physical Infrastructure and Centralised Facilities by adopting CDA and now exporting their products to North America, South America, Europe, Australia, Africa and Asia. The value chain analysis models have been implemented in all the cluster units. This Cluster Development Approach (CDA) model can be implemented in industries of under developed and developing countries for cost reduction and productivity

  2. Fleet Telematics Solution: Influencing Automotive Ecosystem to Drive Greater Business

    OpenAIRE

    Khandwala, Dhwanil

    2017-01-01

    Telematics has given the human-machine interface a new edge. This is improving driving experience significantly. At the base of this enhanced experience are many innovative factors that have been developed to deliver greater business value to manufacturers and dealers. Fleet telematics solutions are heavily inspired by strategic capturing and interchanging of GPS data, effective alignment of the communicational mechanisms between vehicles on road and auto sensors, voice dictated automotive c...

  3. Thermal Comfort Assessment: A Case Study at Malaysian Automotive Industry

    OpenAIRE

    A. R. Ismail; N. Jusoh; R. Zulkifli; K. Sopian; B. M. Deros

    2009-01-01

    Problem statement: Thermal comfort has a great influence on the productivity and satisfaction of indoor building occupants. The exposure to excessive heat during work may cause discomfort and contributed to low productivity among workers. Malaysia known with its hot and humid weather where in most of the survey study published indicated that workers in Malaysia automotive industries had exposed to excessive temperature while working. The study investigated the thermal comfort level experience...

  4. Cost and Price Metrics for Automotive Lithium-Ion Batteries

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-02-01

    Values of current energy technology costs and prices, available from a variety of sources, can sometimes vary. While some of this variation can be due to differences in the specific materials or configurations assumed, it can also reflect differences in the definition and context of the terms "cost" and "price." This fact sheet illustrates and explains this latter source of variation in a case study of automotive lithium-ion batteries.

  5. Assessment of Automotive Coatings Used on Different Metallic Substrates

    OpenAIRE

    Bensalah, W.; Loukil, N.; Wery, M. De-Petris; Ayedi, H. F.

    2014-01-01

    Four epoxy primers commonly used in the automotive industry were applied by gravity pneumatic spray gun over metallic substrates, specifically, steel, electrogalvanized steel, hot-dip galvanized steel, and aluminum. A two-component polyurethane resin was used as topcoat. To evaluate the performance of the different coating systems, the treated panels were submitted to mechanical testing using Persoz hardness, impact resistance, cupping, lattice method, and bending. Tribological properties of ...

  6. Artificial Intelligence and Data Science in the Automotive Industry

    OpenAIRE

    Hofmann, Martin; Neukart, Florian; Bäck, Thomas

    2017-01-01

    Data science and machine learning are the key technologies when it comes to the processes and products with automatic learning and optimization to be used in the automotive industry of the future. This article defines the terms "data science" (also referred to as "data analytics") and "machine learning" and how they are related. In addition, it defines the term "optimizing analytics" and illustrates the role of automatic optimization as a key technology in combination with data analytics. It ...

  7. Adverse effects of the automotive industry on carbon dioxide emissions

    OpenAIRE

    Mpho Bosupeng

    2016-01-01

    This study aims to determine the effects of the automotive industry on carbon dioxide emissions for the period from 1997 to 2010 for diverse economies, as well as the relationships between carbon dioxide discharges and output. The study applies cointegration and causality tests to validate these associations. The results of the Johansen cointegration test depict long-run associations between the quantity of passenger cars and carbon dioxide emissions in France, Sweden, Spain, Hungary and Japa...

  8. Technology Roadmap for Energy Reduction in Automotive Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2008-09-01

    U.S. Department of Energy’s (DOE) Industrial Technologies Program (ITP), in collaboration with the United States Council for Automotive Research LLC (USCAR), hosted a technology roadmap workshop in Troy, Michigan in May 2008. The purpose of the workshop was to explore opportunities for energy reduction, discuss the challenges and barriers that might need to be overcome, and identify priorities for future R&D. The results of the workshop are presented in this report.

  9. Approach of Measuring System Analyses for Automotive Part Manufacturing

    OpenAIRE

    S. Homrossukon; S. Sansureerungsigun

    2014-01-01

    This work aims to introduce an efficient and to standardize the measuring system analyses for automotive industrial. The study started by literature reviewing about the management and analyses measurement system. The approach of measuring system management, then, was constructed. Such approach was validated by collecting the current measuring system data using the equipments of interest including vernier caliper and micrometer. Their accuracy and precision of measurements were analyzed. Final...

  10. Prototyping of automotive components with variable width and depth

    Science.gov (United States)

    Abeyrathna, B.; Rolfe, B.; Harrasser, J.; Sedlmaier, A.; Ge, Rui; Pan, L.; Weiss, M.

    2017-09-01

    Roll forming enables the manufacturing of longitudinal components from materials that combine high strength with limited formability and is increasingly used in the automotive industry for the manufacture of structural and crash components. An extension of conventional roll forming is the Flexible Roll Forming (FRF) process where the rolls are no longer fixed in space but are free to move which enables the forming of components with variable cross section over the length of the part. Even though FRF components have high weight saving potential the technology has found only limited application in the automotive industry. A new flexible forming facility has recently been developed that enables proof of concept studies and the production of FRF prototypes before a full FRF line is built; this may lead to a wider uptake of the FRF technology in the automotive industry. In this process, the pre-cut blank is placed between two clamps and the whole set up moves back and forth; a forming roll that is mounted on a servo-controlled platform with six degrees of freedom forms the pre-cut blank to the desired shape. In this study an initial forming concept for the flexible roll forming of an automotive component with variable height is developed using COPRA® FEA RF. This is followed by performing experimental prototyping studies on the new concept forming facility. Using the optical strain measurement system Autogrid Compact, material deformation, part shape and wrinkling severity are analysed for some forming passes and compared with the numerical results. The results show that the numerical model gives a good representation of material behaviour and that with increasing forming severity wrinkling issues need to be overcome in the process.

  11. Energy and Environmental Challenges for the Japanese Automotive Industry

    OpenAIRE

    Sperling, Daniel

    2000-01-01

    The turn of the century is proving to be a period of turmoil and uncertainty for the automotive industry. The industry confronts growing worldwide demands for greater environmental quality, but now benefits from an emerging technological revolution that provides them with the tools to respond effectively to those demands. Rapid innovation is occurring in lightweight materials, various ICE powertrain enhancements made possible by computer controls, energy conversion processes, energy storage, ...

  12. Nuclear fuels

    International Nuclear Information System (INIS)

    Gangwani, Saloni; Chakrabortty, Sumita

    2011-01-01

    Nuclear fuel is a material that can be consumed to derive nuclear energy, by analogy to chemical fuel that is burned for energy. Nuclear fuels are the most dense sources of energy available. Nuclear fuel in a nuclear fuel cycle can refer to the fuel itself, or to physical objects (for example bundles composed of fuel rods) composed of the fuel material, mixed with structural, neutron moderating, or neutron reflecting materials. Long-lived radioactive waste from the back end of the fuel cycle is especially relevant when designing a complete waste management plan for SNF. When looking at long-term radioactive decay, the actinides in the SNF have a significant influence due to their characteristically long half-lives. Depending on what a nuclear reactor is fueled with, the actinide composition in the SNF will be different. The following paper will also include the uses. advancements, advantages, disadvantages, various processes and behavior of nuclear fuels

  13. Fuel and nuclear fuel cycle

    International Nuclear Information System (INIS)

    Prunier, C.

    1998-01-01

    The nuclear fuel is studied in detail, the best choice and why in relation with the type of reactor, the properties of the fuel cans, the choice of fuel materials. An important part is granted to the fuel assembly of PWR type reactor and the performances of nuclear fuels are tackled. The different subjects for research and development are discussed and this article ends with the particular situation of mixed oxide fuels ( materials, behavior, efficiency). (N.C.)

  14. MSc degree in color technology for the automotive sector

    Science.gov (United States)

    Martinez-Verdu, F.; Perales, E.; Chorro, E.; Viqueira, V.; Gilabert, E.

    2014-07-01

    Nowadays, the measurement and management of color quality of the gonio-apparent materials is complex, but highly demanded in many industrial sectors, as automotive, cosmetics, plastics for consumer electronics, printing inks, architectural coatings, etc. It is necessary to control complex instrumentation and to do visual assessments of texture and color differences to get, for instance, a visual harmony in car bodies; and a profound knowledge of physics and chemistry of special-effect pigments for their optical formulation to obtain attractive visual effects in coatings, plastics, etc, combining among them and with solid pigments. From University of Alicante, for the academic year 2013-14, we are organizing the first MSc degree in Color Technology for the Automotive Sector, with a design of contents embracing CIE colorimetry and visual perception, included the AUDI2000 color difference formula, instrumentation and color management software, fundamentals of coatings and plastics in the automotive sector, and, optical formulation of pigments. The MSc syllabus, with 60 ECTS, is designed to be taught in two semesters: from September to February with on classroom theoretical and practical activities, and, from March to June at virtual level, with internships of training in some companies. Therefore, the MSc Thesis would be the performance report during the internship in companies or research institutions. Some multinational companies, both as car makers and coatings and plastics providers, from European and non-European countries have already shown their support and interest in welcoming students for specific training, even some job offers when the first MSc edition finishes.

  15. Steel skin - SMC laminate structures for lightweight automotive manufacturing

    Science.gov (United States)

    Quagliato, Luca; Jang, Changsoon; Murugesan, Mohanraj; Kim, Naksoo

    2017-09-01

    In the present research work an innovative material, made of steel skin and sheet molding compound core, is presented and is aimed to be utilized for the production of automotive body frames. For a precise description of the laminate structure, the material properties of all the components, including the adhesive utilized as an interlayer, have been carried out, along with the simple tension test of the composite material. The result have shown that the proposed laminate structure has a specific yield strength 114% higher than 6061 T6 aluminum, 34% higher than 7075 T6 aluminum, 186% higher than AISI 304 stainless steel (30HRC) and 42% than SK5 high-strength steel (52HRC), showing its reliability and convenience for the realization of automotive components. After calibrating the material properties of the laminate structure, and utilizing as reference the simple tension results of the laminate structure, the derived material properties have been utilized for the simulation of the mechanical behavior of an automotive B-pillar. The results have been compared with those of a standard B-pillar made of steel, showing that the MS-SMC laminate structure manifests load and impact carry capacity comparable with those of high strength steel, while granting, at least, an 11% weight reduction.

  16. Nano-crystalline P/M aluminium for automotive applications

    International Nuclear Information System (INIS)

    Hummert, K; Schattevoy, R; Broda, M; Knappe, M; Beiss, P; Klubberg, F; Schubert, T H; Leuschner, R

    2009-01-01

    The reduction of total vehicle weight and lowering of moving masses within the engine are key elements to overcome future emission challenges of the automotive industry. Within a German BMBF funded project the melt spinning technology will be driven to a series production status. The very fast cooling condition of the melt leads to a nano-structure of the aluminium material. This results in new material properties of known alloys. The strength increases dramatically without lowered forming behaviour. With this process the freedom of designing complex alloys is very flexible. Different alloys have been investigated for several applications, where high strength at room and elevated temperatures and/or high wear resistance is required. This paper presents some results regarding the processing, microstructure and mechanical properties of a developed Al-Ni-Fe alloy. This joined research project with partners from the automotive industry as well as automotive suppliers and universities is funded by the German BMBF 'NanoMobile' Program under Project number 03X3008.

  17. Advantages and challenges of dissimilar materials in automotive lightweight construction

    Science.gov (United States)

    Weberpals, Jan-Philipp; Schmidt, Philipp A.; Böhm, Daniel; Müller, Steffen

    2015-03-01

    The core of future automotive lightweight materials is the joining technology of various material mixes. The type of joining will be essential, particularly in electrified propulsion systems, especially as an improved electrical energy transmission leads to a higher total efficiency of the vehicle. The most evident parts to start the optimization process are the traction battery, the electrical performance modules and the engines. Consequently aluminum plays a very central role for lightweight construction applications. However, the physical-technical requirements of components often require the combination with other materials. Thus the joining of mixed material connections is an essential key technology for many of the current developments, for example in the areas E-Mobility, solar energy and lightweight construction. Due to these advantages mixed material joints are already established in the automotive industry and laser beam remote welding is now a focus technology for mixed material connections. The secret of the laser welding process with mixed materials lies within the different areas of the melting phase diagram depending on the mixing ratio and the cooling down rate. According to that areas with unwanted, prim, intermetallic phases arise in the fusion zone. Therefore, laser welding of mixed material connections can currently only be used with additional filler in the automotive industry.

  18. Impact of national cultures on automotive after sales services perception

    Directory of Open Access Journals (Sweden)

    Jose Albors-Garrigos

    2017-09-01

    Full Text Available This article clarifies the impact of national culture in the after sales service in the automotive sector. Introduction and objectives: After-sales services have become paramount in the automobile industry. However, they are not sufficiently researched, particularly in emerging markets. Here an academic gap exists because, within the automotive research literature, culture is a widely neglected issue. Thus no explicit knowledge can be applied regarding emerging markets service demand behaviour, which might be a crucial point, as some of these countries culture is different to the western culture. Methods: The research is based in a survey carried out among Chinese premium brand automotive customers. Results: It shows which individual level values are causal and positively contribute to the perception of service quality and loyalty behaviour by customers. Conclusion: The article providing a guideline how the entire process chain of after-sales services could be researched and applies successfully the individual level value theory by Schwartz. Implications and research limitation: Brand loyalty is well explained by perceived service quality significantly leads to after-sales service satisfaction, which itself is a strong predictor of workshop loyalty. Moreover, workshop loyal customers are likewise significantly brand loyal. Finally, the influence of culture is empirically verified with the one exception of after-sales service satisfaction.

  19. Modelling Electrical Energy Consumption in Automotive Paint Shop

    Science.gov (United States)

    Oktaviandri, Muchamad; Safiee, Aidil Shafiza Bin

    2018-03-01

    Industry players are seeking ways to reduce operational cost to sustain in a challenging economic trend. One key aspect is an energy cost reduction. However, implementing energy reduction strategy often struggle with obstructions, which slow down their realization and implementation. Discrete event simulation method is an approach actively discussed in current research trend to overcome such obstructions because of its flexibility and comprehensiveness. Meanwhile, in automotive industry, paint shop is considered the most energy consumer area which is reported consuming about 50%-70% of overall automotive plant consumption. Hence, this project aims at providing a tool to model and simulate energy consumption at paint shop area by conducting a case study at XYZ Company, one of the automotive companies located at Pekan, Pahang. The simulation model was developed using Tecnomatix Plant Simulation software version 13. From the simulation result, the model was accurately within ±5% for energy consumption and ±15% for maximum demand after validation with real system. Two different energy saving scenarios were tested. Scenario 1 was based on production scheduling approach under low demand situation which results energy saving up to 30% on the consumption. Meanwhile scenario 2 was based on substituting high power compressor with the lower power compressor. The results were energy consumption saving of approximately 1.42% and maximum demand reduction about 1.27%. This approach would help managers and engineers to justify worthiness of investment for implementing the reduction strategies.

  20. DEVELOPING VENDOR IMPROVEMENT PROGRAM IN MALAYSIA AUTOMOTIVE COMPANY

    Directory of Open Access Journals (Sweden)

    SHUKRIAH ABDULLAH

    2016-04-01

    Full Text Available Improvement Program seek to do evaluation well, request to become sufficiently versed in evaluation or to integrate on improvement perspective in all phase of performance, from needs assessment to implementation and evaluation itself. The purpose of this program in the automotive company is to assist vendor as global manufacturer in preparation towards ASEAN Free Trade Agreement (AFTA 2015. This development vendor improvement program emphasize on the downtime reduction to below 200 minutes per month with the ultimate end of improving not only program or solutions but also the organizations and customer. A practical approach either planned or unplanned by the automotive company require policies and procedures that address the same consideration on the downtime identification. 20 top bottom rank vendor were determined based on the downtime performance, followed by classification into different group based on severity. To execute the vendor improvement program three among 20 top bottom rank vendors were selected due to willingness to participate and ease of data access in the program. Selected vendors have high ranking in terms of downtime. The case study method involved an interview and plant observation. The used of secondary data from the automotive company, and previous researcher are also utilised. This improvement program assists the automobile manufacturer to improve its supplier’s performance. The vendor improvement program is implemented through a whole supplier operation assessment.