Generalized Asynchronous Systems

Directory of Open Access Journals (Sweden)

E. S. Kudryashova

2012-01-01

Full Text Available The paper consider a mathematical model of a concurrent system, the special case of which is an asynchronous system. Distributed asynchronous automata are introduced here. It is proved that Petri nets and transition systems with independence can be considered as distributed asynchronous automata. Time distributed asynchronous automata are defined in a standard way by correspondence which relates events with time intervals. It is proved that the time distributed asynchronous automata generalize time Petri nets and asynchronous systems.

Localized radio frequency communication using asynchronous transfer mode protocol

Science.gov (United States)

Witzke, Edward L.; Robertson, Perry J.; Pierson, Lyndon G.

2007-08-14

A localized wireless communication system for communication between a plurality of circuit boards, and between electronic components on the circuit boards. Transceivers are located on each circuit board and electronic component. The transceivers communicate with one another over spread spectrum radio frequencies. An asynchronous transfer mode protocol controls communication flow with asynchronous transfer mode switches located on the circuit boards.

Developing asynchronous online interprofessional education.

Science.gov (United States)

Sanborn, Heidi

2016-09-01

For many health programmes, developing interprofessional education (IPE) has been a challenge. Evidence on the best method for design and implementation of IPE has been slow to emerge, with little research on how to best incorporate IPE in the asynchronous online learning environment. This leaves online programmes with no clear guidance when embarking upon an initiative to integrate IPE into the curriculum. One tool that can be effective at guiding the incorporation of IPE across all learning platforms is the Interprofessional Education Collaborative (IPEC) competencies. A project was designed to integrate the nationally defined IPEC competencies throughout an asynchronous, online baccalaureate nursing completion programme. A programme-wide review led to targeted revision of course and unit-level objectives, learning experiences, and assessments based on the IPEC framework. As a result of this effort, the programme curriculum now provides interprofessional learning activities across all courses. This report provides a method for using the IPEC competencies to incorporate IPE within various asynchronous learning assessments, assuring students learn about, with, and from other professions.

Low-power Implementation of an Encryption/Decryption System with Asynchronous Techniques

Directory of Open Access Journals (Sweden)

Nikos Sklavos

2002-01-01

Full Text Available An asynchronous VLSI implementation of the International Data Encryption Algorithm (IDEA is presented in this paper. In order to evaluate the asynchronous design a synchronous version of the algorithm was also designed. VHDL hardware description language was used in order to describe the algorithm. By using Synopsys commercial available tools the VHDL code was synthesized. After placing and routing both designs were fabricated with 0.6 μm CMOS technology. With a system clock of up to 8 MHz and a power supply of 5 V the two chips were tested and evaluated comparing with the software implementation of the IDEA algorithm. This new approach proves efficiently the lowest power consumption of the asynchronous implementation compared to the existing synchronous. Therefore, the asynchronous chip performs efficiently in Wireless Encryption Protocols and high speed networks.

Low latency asynchronous interface circuits

Science.gov (United States)

Sadowski, Greg

2017-06-20

In one form, a logic circuit includes an asynchronous logic circuit, a synchronous logic circuit, and an interface circuit coupled between the asynchronous logic circuit and the synchronous logic circuit. The asynchronous logic circuit has a plurality of asynchronous outputs for providing a corresponding plurality of asynchronous signals. The synchronous logic circuit has a plurality of synchronous inputs corresponding to the plurality of asynchronous outputs, a stretch input for receiving a stretch signal, and a clock output for providing a clock signal. The synchronous logic circuit provides the clock signal as a periodic signal but prolongs a predetermined state of the clock signal while the stretch signal is active. The asynchronous interface detects whether metastability could occur when latching any of the plurality of the asynchronous outputs of the asynchronous logic circuit using said clock signal, and activates the stretch signal while the metastability could occur.

FPGA BASED ASYNCHRONOUS PIPELINED MB-OFDM UWB TRANSMITTER BACKEND MODULES

Directory of Open Access Journals (Sweden)

M. Santhi

2010-03-01

Full Text Available In this paper, a novel scheme is proposed which comprises the advantages of asynchronous pipelining techniques and the advantages of FPGAs for implementing a 200Mbps MB-OFDM UWB transmitter digital backend modules. In asynchronous pipelined system, registers are used as in synchronous system. But they are controlled by handshaking signals. Since FPGAs are rich in registers, design and implementation of asynchronous pipelined MBOFDM UWB transmitter on FPGA using four-phase bundled-data protocol is considered in this paper. Novel ideas have also been proposed for designing asynchronous OFDM using Modified Radix-24 SDF and asynchronous interleaver using two RAM banks. Implementation has been performed on ALTERA STRATIX II EP2S60F1020C4 FPGA and it is operating at a speed of 350MHz. It is assured that the proposed MB-OFDM UWB system can be made to work on STRATIX III device with the operating frequency of 528MHz in compliance to the ECMA-368 standard. The proposed scheme is also applicable for FPGA from other vendors and ASIC.

Blending Online Asynchronous and Synchronous Learning

Directory of Open Access Journals (Sweden)

Lisa C. Yamagata-Lynch

2014-04-01

Full Text Available In this article I will share a qualitative self-study about a 15-week blended 100% online graduate level course facilitated through synchronous meetings on Blackboard Collaborate and asynchronous discussions on Blackboard. I taught the course at the University of Tennessee (UT during the spring 2012 semester and the course topic was online learning environments. The primary research question of this study was: How can the designer/instructor optimize learning experiences for students who are studying about online learning environments in a blended online course relying on both synchronous and asynchronous technologies? I relied on student reflections of course activities during the beginning, middle, and the end of the semester as the primary data source to obtain their insights regarding course experiences. Through the experiences involved in designing and teaching the course and engaging in this study I found that there is room in the instructional technology research community to address strategies for facilitating online synchronous learning that complement asynchronous learning. Synchronous online whole class meetings and well-structured small group meetings can help students feel a stronger sense of connection to their peers and instructor and stay engaged with course activities. In order to provide meaningful learning spaces in synchronous learning environments, the instructor/designer needs to balance the tension between embracing the flexibility that the online space affords to users and designing deliberate structures that will help them take advantage of the flexible space.

The queueing perspective of asynchronous network coding in two-way relay network

Science.gov (United States)

Liang, Yaping; Chang, Qing; Li, Xianxu

2018-04-01

Asynchronous network coding (NC) has potential to improve the wireless network performance compared with a routing or the synchronous network coding. Recent researches concentrate on the optimization between throughput/energy consuming and delay with a couple of independent input flow. However, the implementation of NC requires a thorough investigation of its impact on relevant queueing systems where few work focuses on. Moreover, few works study the probability density function (pdf) in network coding scenario. In this paper, the scenario with two independent Poisson input flows and one output flow is considered. The asynchronous NC-based strategy is that a new arrival evicts a head packet holding in its queue when waiting for another packet from the other flow to encode. The pdf for the output flow which contains both coded and uncoded packets is derived. Besides, the statistic characteristics of this strategy are analyzed. These results are verified by numerical simulations.

Argo: A Time-Elastic Time-Division-Multiplexed NOC using Asynchronous Routers

DEFF Research Database (Denmark)

Kasapaki, Evangelia; Sparsø, Jens

2014-01-01

are either synchronous or mesochronous. We use asynchronous routers to achieve a simpler, smaller, and more robust, self-timed design. Our design exploits the fact that pipelined asynchronous circuits also behave as ripple FIFOs. Thus, it avoids the need for explicit synchronization FIFOs between the routers......In this paper we explore the use of asynchronous routers in a time-division-multiplexed (TDM) network-on-chip (NOC), Argo, that is being developed for a multi-processor platform for hard real-time systems. TDM inherently requires a common time reference, and existing TDM-based NOC designs...... delays derived from a 65nm CMOS implementation, a worstcase analysis shows that a typical design can tolerate a skew of 1-5 cycles (depending on FIFO depths and NI clock frequency). Simulation results of a 2 x 2 NOC confirm this....

Exploring effectiveness of team communication: Balancing synchronous and asynchronous communication in design teams

DEFF Research Database (Denmark)

den Otter, Ad; Emmitt, Stephen

2007-01-01

Effective teams use a balance of synchronous and asynchronous communication. Team communication is dependent on the communication acts of team members and the ability of managers to facilitate, stimulate and motivate them. Team members from organizations using different information systems tend...... to have different understanding, opinions, and rates of adoption and skills levels regarding specific IT tools. The purpose of this paper is to explore the effective use of tools for communication in design teams and the strategies for the use of specific tools....

Asynchronous schemes for CFD at extreme scales

Science.gov (United States)

Konduri, Aditya; Donzis, Diego

2013-11-01

Recent advances in computing hardware and software have made simulations an indispensable research tool in understanding fluid flow phenomena in complex conditions at great detail. Due to the nonlinear nature of the governing NS equations, simulations of high Re turbulent flows are computationally very expensive and demand for extreme levels of parallelism. Current large simulations are being done on hundreds of thousands of processing elements (PEs). Benchmarks from these simulations show that communication between PEs take a substantial amount of time, overwhelming the compute time, resulting in substantial waste in compute cycles as PEs remain idle. We investigate a novel approach based on widely used finite-difference schemes in which computations are carried out asynchronously, i.e. synchronization of data among PEs is not enforced and computations proceed regardless of the status of messages. This drastically reduces PE idle time and results in much larger computation rates. We show that while these schemes remain stable, their accuracy is significantly affected. We present new schemes that maintain accuracy under asynchronous conditions and provide a viable path towards exascale computing. Performance of these schemes will be shown for simple models like Burgers' equation.

Asynchronous stream processing with S-Net

NARCIS (Netherlands)

Grelck, C.; Scholz, S.-B.; Shafarenko, A.

2010-01-01

We present the rationale and design of S-Net, a coordination language for asynchronous stream processing. The language achieves a near-complete separation between the application code, written in any conventional programming language, and the coordination/communication code written in S-Net. Our

Basic Algorithms for the Asynchronous Reconfigurable Mesh

Directory of Open Access Journals (Sweden)

Yosi Ben-Asher

2002-01-01

Full Text Available Many constant time algorithms for various problems have been developed for the reconfigurable mesh (RM in the past decade. All these algorithms are designed to work with synchronous execution, with no regard for the fact that large size RMs will probably be asynchronous. A similar observation about the PRAM model motivated many researchers to develop algorithms and complexity measures for the asynchronous PRAM (APRAM. In this work, we show how to define the asynchronous reconfigurable mesh (ARM and how to measure the complexity of asynchronous algorithms executed on it. We show that connecting all processors in a row of an n×n ARM (the analog of barrier synchronization in the APRAM model can be solved with complexity Θ(nlog⁡n. Intuitively, this is average work time for solving such a problem. Next, we describe general a technique for simulating T -step synchronous RM algorithms on the ARM with complexity of Θ(T⋅n2log⁡n. Finally, we consider the simulation of the classical synchronous algorithm for counting the number of non-zero bits in an n bits vector using (k

Novel Asynchronous Wrapper and Its Application to GALS Systems

Institute of Scientific and Technical Information of China (English)

Zhuang Shengxian; Peng Anjin; Lars Wanhammar

2006-01-01

An asynchronous wrapper with novel handshake circuits for data communication in globally asynchronous locally synchronous (GALS) systems is proposed. The handshake circuits include two communication ports and a local clock generator. Two approaches for the implementation of communication ports are presented, one with pure standard cells and the others with Müller-C elements. The detailed design methodology for GALS systems is given and the circuits are validated with VHDL and circuits simulation in standard CMOS technology.

Modeling and Analysis of Asynchronous Systems Using SAL and Hybrid SAL

Science.gov (United States)

Tiwari, Ashish; Dutertre, Bruno

2013-01-01

We present formal models and results of formal analysis of two different asynchronous systems. We first examine a mid-value select module that merges the signals coming from three different sensors that are each asynchronously sampling the same input signal. We then consider the phase locking protocol proposed by Daly, Hopkins, and McKenna. This protocol is designed to keep a set of non-faulty (asynchronous) clocks phase locked even in the presence of Byzantine-faulty clocks on the network. All models and verifications have been developed using the SAL model checking tools and the Hybrid SAL abstractor.

Embedded Vehicle Speed Estimation System Using an Asynchronous Temporal Contrast Vision Sensor

Directory of Open Access Journals (Sweden)

D. Bauer

2007-01-01

Full Text Available This article presents an embedded multilane traffic data acquisition system based on an asynchronous temporal contrast vision sensor, and algorithms for vehicle speed estimation developed to make efficient use of the asynchronous high-precision timing information delivered by this sensor. The vision sensor features high temporal resolution with a latency of less than 100 μs, wide dynamic range of 120 dB of illumination, and zero-redundancy, asynchronous data output. For data collection, processing and interfacing, a low-cost digital signal processor is used. The speed of the detected vehicles is calculated from the vision sensor's asynchronous temporal contrast event data. We present three different algorithms for velocity estimation and evaluate their accuracy by means of calibrated reference measurements. The error of the speed estimation of all algorithms is near zero mean and has a standard deviation better than 3% for both traffic flow directions. The results and the accuracy limitations as well as the combined use of the algorithms in the system are discussed.

A Fault Detection Mechanism in a Data-flow Scheduled Multithreaded Processor

NARCIS (Netherlands)

Fu, J.; Yang, Q.; Poss, R.; Jesshope, C.R.; Zhang, C.

2014-01-01

This paper designs and implements the Redundant Multi-Threading (RMT) in a Data-flow scheduled MultiThreaded (DMT) multicore processor, called Data-flow scheduled Redundant Multi-Threading (DRMT). Meanwhile, It presents Asynchronous Output Comparison (AOC) for RMT techniques to avoid fault detection

Snowball Earth: Asynchronous coupling of sea-glacier flow with a global climate model

Science.gov (United States)

Pollard, D.; Kasting, J. F.; Zugger, M. E.

2017-05-01

During Snowball Earth episodes of the Neoproterozoic and Paleoproterozoic, limited amounts of tropical open ocean (Jormungand), or tropical ocean with thin ice cover, would help to explain (1) vigorous glacial activity in low latitudes, (2) survival of photosynthetic life, and (3) deglacial recovery without excessive buildup of atmospheric CO2. Some previous models have suggested that tropical open ocean or thin-ice cover is possible; however, its viability in the presence of kilometer-thick sea glaciers flowing from higher latitudes has not been demonstrated conclusively. Here we describe a new method of asynchronously coupling a zonal sea-glacier model with a 3-D global climate model and apply it to Snowball Earth. Equilibrium curves of ice line versus CO2 are mapped out, as well as their dependence on ocean heat transport efficiency, sea-glacier flow, and other model parameters. No climate states with limited tropical open ocean or thin ice are found in any of our model runs, including those with sea glaciers. If this result is correct, then other refugia such as cryoconite pans would have been required for life to survive. However, the reasons for the differences between our results and others should first be resolved. It is suggested that small-scale convective dynamics, affecting fractional snow cover in low latitudes, may be a critical factor accounting for these differences.

An Asynchronous Low Power and High Performance VLSI Architecture for Viterbi Decoder Implemented with Quasi Delay Insensitive Templates

Directory of Open Access Journals (Sweden)

T. Kalavathi Devi

2015-01-01

Full Text Available Convolutional codes are comprehensively used as Forward Error Correction (FEC codes in digital communication systems. For decoding of convolutional codes at the receiver end, Viterbi decoder is often used to have high priority. This decoder meets the demand of high speed and low power. At present, the design of a competent system in Very Large Scale Integration (VLSI technology requires these VLSI parameters to be finely defined. The proposed asynchronous method focuses on reducing the power consumption of Viterbi decoder for various constraint lengths using asynchronous modules. The asynchronous designs are based on commonly used Quasi Delay Insensitive (QDI templates, namely, Precharge Half Buffer (PCHB and Weak Conditioned Half Buffer (WCHB. The functionality of the proposed asynchronous design is simulated and verified using Tanner Spice (TSPICE in 0.25 µm, 65 nm, and 180 nm technologies of Taiwan Semiconductor Manufacture Company (TSMC. The simulation result illustrates that the asynchronous design techniques have 25.21% of power reduction compared to synchronous design and work at a speed of 475 MHz.

A low-power asynchronous data-path for a FIR filter bank

DEFF Research Database (Denmark)

Nielsen, Lars Skovby; Sparsø, Jens

1996-01-01

This paper describes a number of design issues relating to the implementation of low-power asynchronous signal processing circuits. Specifically, the paper addresses the design of a dedicated processor structure that implements an audio FIR filter bank which is part of an industrial application....... The algorithm requires a fixed number of steps and the moderate speed requirement allows a sequential implementation. The latter, in combination with a huge predominance of numerically small data values in the input data stream, is the key to a low-power asynchronous implementation. Power is minimized in two...

Information flow vs resource access in the asynchronous pi-calculus.

OpenAIRE

HENNESSY, MATTHEW

2002-01-01

PUBLISHED We propose an extension of the asynchronous ?-calculus in which a variety of security properties may be captured using types. These are an extension of the input/output types for the ?-calculus in which I/O capabilities are assigned specific security levels. The main innovation is a uniform typing system that, by varying slightly the allowed set of types, captures different notions of security.We first define a typing system that ensures that processes running at security level ?...

Determination of power and moment on shaft of special asynchronous electric drives

Science.gov (United States)

Karandey, V. Yu; Popov, B. K.; Popova, O. B.; Afanasyev, V. L.

2018-03-01

In the article, questions and tasks of determination of power and the moment on a shaft of special asynchronous electric drives are considered. Use of special asynchronous electric drives in mechanical engineering and other industries is relevant. The considered types of electric drives possess the improved mass-dimensional indicators in comparison with singleengine systems. Also these types of electric drives have constructive advantages; the improved characteristics allow one to realize the technological process. But creation and design of new electric drives demands adjustment of existing or development of new methods and approaches of calculation of parameters. Determination of power and the moment on a shaft of special asynchronous electric drives is the main objective during design of electric drives. This task has been solved based on a method of electromechanical transformation of energy.

Asynchronous LMS adaptive equalization

NARCIS (Netherlands)

Bergmans, J.W.M.; Lin, M.Y.; Modrie, D.; Otte, R.

2005-01-01

Digital data receivers often operate at a fixed sampling rate 1/Ts that is asynchronous to the baud rate 1/T. A digital equalizer that processes the incoming signal will also operate in the asynchronous clock domain. Existing adaptation techniques for this equalizer involve an error sequence ek that

Information flow vs. resource access in the asynchronous pi-calculus

OpenAIRE

Hennessy, Matthew; Riely, James

2002-01-01

We propose an extension of the asynchronous π-calculus in which a variety of security properties may be captured using types. These are an extension of the input/output types for the π-calculus in which I/O capabilities are assigned specific security levels. The main innovation is a uniform typing system that, by varying slightly the allowed set of types, captures different notions of security.We first define a typing system that ensures that processes running at security level σ cannot acces...

A Methodology for the Design and Verification of Globally Asynchronous/Locally Synchronous Architectures

Science.gov (United States)

Miller, Steven P.; Whalen, Mike W.; O'Brien, Dan; Heimdahl, Mats P.; Joshi, Anjali

2005-01-01

Recent advanced in model-checking have made it practical to formally verify the correctness of many complex synchronous systems (i.e., systems driven by a single clock). However, many computer systems are implemented by asynchronously composing several synchronous components, where each component has its own clock and these clocks are not synchronized. Formal verification of such Globally Asynchronous/Locally Synchronous (GA/LS) architectures is a much more difficult task. In this report, we describe a methodology for developing and reasoning about such systems. This approach allows a developer to start from an ideal system specification and refine it along two axes. Along one axis, the system can be refined one component at a time towards an implementation. Along the other axis, the behavior of the system can be relaxed to produce a more cost effective but still acceptable solution. We illustrate this process by applying it to the synchronization logic of a Dual Fight Guidance System, evolving the system from an ideal case in which the components do not fail and communicate synchronously to one in which the components can fail and communicate asynchronously. For each step, we show how the system requirements have to change if the system is to be implemented and prove that each implementation meets the revised system requirements through modelchecking.

Pro asynchronous programming with .NET

CERN Document Server

Blewett, Richard; Ltd, Rock Solid Knowledge

2014-01-01

Pro Asynchronous Programming with .NET teaches the essential skill of asynchronous programming in .NET. It answers critical questions in .NET application development, such as: how do I keep my program responding at all times to keep my users happy how do I make the most of the available hardware how can I improve performanceIn the modern world, users expect more and more from their applications and devices, and multi-core hardware has the potential to provide it. But it takes carefully crafted code to turn that potential into responsive, scalable applications.With Pro Asynchronous Programming

Asynchronized synchronous machines

CERN Document Server

Botvinnik, M M

1964-01-01

Asynchronized Synchronous Machines focuses on the theoretical research on asynchronized synchronous (AS) machines, which are "hybrids” of synchronous and induction machines that can operate with slip. Topics covered in this book include the initial equations; vector diagram of an AS machine; regulation in cases of deviation from the law of full compensation; parameters of the excitation system; and schematic diagram of an excitation regulator. The possible applications of AS machines and its calculations in certain cases are also discussed. This publication is beneficial for students and indiv

FAST: A fully asynchronous and status-tracking pattern for geoprocessing services orchestration

Science.gov (United States)

Wu, Huayi; You, Lan; Gui, Zhipeng; Gao, Shuang; Li, Zhenqiang; Yu, Jingmin

2014-09-01

Geoprocessing service orchestration (GSO) provides a unified and flexible way to implement cross-application, long-lived, and multi-step geoprocessing service workflows by coordinating geoprocessing services collaboratively. Usually, geoprocessing services and geoprocessing service workflows are data and/or computing intensive. The intensity feature may make the execution process of a workflow time-consuming. Since it initials an execution request without blocking other interactions on the client side, an asynchronous mechanism is especially appropriate for GSO workflows. Many critical problems remain to be solved in existing asynchronous patterns for GSO including difficulties in improving performance, status tracking, and clarifying the workflow structure. These problems are a challenge when orchestrating performance efficiency, making statuses instantly available, and constructing clearly structured GSO workflows. A Fully Asynchronous and Status-Tracking (FAST) pattern that adopts asynchronous interactions throughout the whole communication tier of a workflow is proposed for GSO. The proposed FAST pattern includes a mechanism that actively pushes the latest status to clients instantly and economically. An independent proxy was designed to isolate the status tracking logic from the geoprocessing business logic, which assists the formation of a clear GSO workflow structure. A workflow was implemented in the FAST pattern to simulate the flooding process in the Poyang Lake region. Experimental results show that the proposed FAST pattern can efficiently tackle data/computing intensive geoprocessing tasks. The performance of all collaborative partners was improved due to the asynchronous mechanism throughout communication tier. A status-tracking mechanism helps users retrieve the latest running status of a GSO workflow in an efficient and instant way. The clear structure of the GSO workflow lowers the barriers for geospatial domain experts and model designers to

Pseudo Asynchronous Level Crossing adc for ecg Signal Acquisition.

Science.gov (United States)

Marisa, T; Niederhauser, T; Haeberlin, A; Wildhaber, R A; Vogel, R; Goette, J; Jacomet, M

2017-02-07

A new pseudo asynchronous level crossing analogue-to-digital converter (adc) architecture targeted for low-power, implantable, long-term biomedical sensing applications is presented. In contrast to most of the existing asynchronous level crossing adc designs, the proposed design has no digital-to-analogue converter (dac) and no continuous time comparators. Instead, the proposed architecture uses an analogue memory cell and dynamic comparators. The architecture retains the signal activity dependent sampling operation by generating events only when the input signal is changing. The architecture offers the advantages of smaller chip area, energy saving and fewer analogue system components. Beside lower energy consumption the use of dynamic comparators results in a more robust performance in noise conditions. Moreover, dynamic comparators make interfacing the asynchronous level crossing system to synchronous processing blocks simpler. The proposed adc was implemented in [Formula: see text] complementary metal-oxide-semiconductor (cmos) technology, the hardware occupies a chip area of 0.0372 mm 2 and operates from a supply voltage of [Formula: see text] to [Formula: see text]. The adc's power consumption is as low as 0.6 μW with signal bandwidth from [Formula: see text] to [Formula: see text] and achieves an equivalent number of bits (enob) of up to 8 bits.

Asynchronous L1-gain control of uncertain switched positive linear systems with dwell time.

Science.gov (United States)

Li, Yang; Zhang, Hongbin

2018-04-01

In this paper, dwell time (DT) stability, L 1 -gain performance analysis and asynchronous L 1 -gain controller design problems of uncertain switched positive linear systems (SPLSs) are investigated. Via a time-scheduled multiple linear co-positive Lyapunov function (TSMLCLF) approach, convex sufficient conditions of DT stability and L 1 -gain performance of SPLSs with interval and polytopic uncertainties are presented. Furthermore, by utilizing the feature that the TSMLCLF keeps decreasing even if the controller is running asynchronously with the system, the asynchronous L 1 -gain controller design problem of SPLSs with interval and polytopic uncertainties is investigated. Convex sufficient conditions of the existence of time-varying asynchronous state-feedback controller which can ensure the closed-loop system's positivity, stability and L 1 -gain performance are established, and the controller gain matrices can be calculated instantaneously online. The obtained L 1 -gain in the paper is standard. All the results are presented in terms of linear programming. A practical example is provided to show the effectiveness of the results. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Asynchronous zero-forcing adaptive equalization

NARCIS (Netherlands)

Bergmans, J.W.M.; Pozidis, H.; Lin, M.Y.

2005-01-01

Digital data receivers often operate at a fixed sampling rate 1/Ts that is asynchronous to the baud rate 1/T. A digital equalizer that processes the incoming signal will also be asynchronous, and its adaptation is commonly based on extensions of the LMS algorithm. In this paper, we develop and

The Aeolian Asynchronous Generator

Directory of Open Access Journals (Sweden)

Ionel Dragomirescu

2008-10-01

Full Text Available The production of the electric energy with lower costs could be realized with the help of the aeolian electric central. In these centrals we can use the squirrel cage asynchronous generators, because these machines are the most safety in function and easy exploited. This work show the function analyzing of the asynchronous generator having on involving torque depending on the square wind speed, the air-density and on the construction of the wing spiral.

Methodological Reflections on the Use of Asynchronous Online Focus Groups in Health Research

Directory of Open Access Journals (Sweden)

Sarah Williams PhD

2012-09-01

Full Text Available The Internet is increasingly used as a tool in qualitative research. In particular, asynchronous online focus groups are used when factors such as cost, time, or access to participants can make conducting face-to-face research difficult. In this article we consider key methodological issues involved in using asynchronous online focus groups to explore experiences of health and illness. The written nature of Internet communication, the lack of physical presence, and the asynchronous, longitudinal aspects enable participants who might not normally contribute to research studies to reflect on their personal stories before disclosing them to the researcher. Implications for study design, recruitment strategies, and ethics should be considered when deciding whether to use this method.

An improved asynchronous brain interface: making use of the temporal history of the LF-ASD feature vectors

Science.gov (United States)

Bashashati, Ali; Mason, Steve; Ward, Rabab K.; Birch, Gary E.

2006-06-01

The low-frequency asynchronous switch design (LF-ASD) has been introduced as a direct brain interface (BI) for asynchronous control applications. Asynchronous interfaces, as opposed to synchronous interfaces, have the advantage of being operational at all times and not only at specific system-defined periods. This paper modifies the LF-ASD design by incorporating into the system more knowledge about the attempted movements. Specifically, the history of feature values extracted from the EEG signal is used to detect a right index finger movement attempt. Using data collected from individuals with high-level spinal cord injuries and able-bodied subjects, it is shown that the error characteristics of the modified design are significantly better than the previous LF-ASD design. The true positive rate percentage increased by up to 15 which corresponds to 50% improvement when the system is operating with false positive rates in the 1-2% range.

Exploring effectiveness of team communication: Balancing synchronous and asynchronous communication in design teams

NARCIS (Netherlands)

Otter, den A.F.H.J.; Emmitt, S.

2007-01-01

Purpose – Effective teams use a balance of synchronous and asynchronous communication. Team communication is dependent on the communication acts of team members and the ability of managers to facilitate, stimulate and motivate them. Team members from organizations using different information systems

A Parallel Particle Swarm Optimization Algorithm Accelerated by Asynchronous Evaluations

Science.gov (United States)

Venter, Gerhard; Sobieszczanski-Sobieski, Jaroslaw

2005-01-01

A parallel Particle Swarm Optimization (PSO) algorithm is presented. Particle swarm optimization is a fairly recent addition to the family of non-gradient based, probabilistic search algorithms that is based on a simplified social model and is closely tied to swarming theory. Although PSO algorithms present several attractive properties to the designer, they are plagued by high computational cost as measured by elapsed time. One approach to reduce the elapsed time is to make use of coarse-grained parallelization to evaluate the design points. Previous parallel PSO algorithms were mostly implemented in a synchronous manner, where all design points within a design iteration are evaluated before the next iteration is started. This approach leads to poor parallel speedup in cases where a heterogeneous parallel environment is used and/or where the analysis time depends on the design point being analyzed. This paper introduces an asynchronous parallel PSO algorithm that greatly improves the parallel e ciency. The asynchronous algorithm is benchmarked on a cluster assembled of Apple Macintosh G5 desktop computers, using the multi-disciplinary optimization of a typical transport aircraft wing as an example.

Area/latency optimized early output asynchronous full adders and relative-timed ripple carry adders.

Science.gov (United States)

Balasubramanian, P; Yamashita, S

2016-01-01

This article presents two area/latency optimized gate level asynchronous full adder designs which correspond to early output logic. The proposed full adders are constructed using the delay-insensitive dual-rail code and adhere to the four-phase return-to-zero handshaking. For an asynchronous ripple carry adder (RCA) constructed using the proposed early output full adders, the relative-timing assumption becomes necessary and the inherent advantages of the relative-timed RCA are: (1) computation with valid inputs, i.e., forward latency is data-dependent, and (2) computation with spacer inputs involves a bare minimum constant reverse latency of just one full adder delay, thus resulting in the optimal cycle time. With respect to different 32-bit RCA implementations, and in comparison with the optimized strong-indication, weak-indication, and early output full adder designs, one of the proposed early output full adders achieves respective reductions in latency by 67.8, 12.3 and 6.1 %, while the other proposed early output full adder achieves corresponding reductions in area by 32.6, 24.6 and 6.9 %, with practically no power penalty. Further, the proposed early output full adders based asynchronous RCAs enable minimum reductions in cycle time by 83.4, 15, and 8.8 % when considering carry-propagation over the entire RCA width of 32-bits, and maximum reductions in cycle time by 97.5, 27.4, and 22.4 % for the consideration of a typical carry chain length of 4 full adder stages, when compared to the least of the cycle time estimates of various strong-indication, weak-indication, and early output asynchronous RCAs of similar size. All the asynchronous full adders and RCAs were realized using standard cells in a semi-custom design fashion based on a 32/28 nm CMOS process technology.

Comparing the force ripple during asynchronous and conventional stimulation.

Science.gov (United States)

Downey, Ryan J; Tate, Mark; Kawai, Hiroyuki; Dixon, Warren E

2014-10-01

Asynchronous stimulation has been shown to reduce fatigue during electrical stimulation; however, it may also exhibit a force ripple. We quantified the ripple during asynchronous and conventional single-channel transcutaneous stimulation across a range of stimulation frequencies. The ripple was measured during 5 asynchronous stimulation protocols, 2 conventional stimulation protocols, and 3 volitional contractions in 12 healthy individuals. Conventional 40 Hz and asynchronous 16 Hz stimulation were found to induce contractions that were as smooth as volitional contractions. Asynchronous 8, 10, and 12 Hz stimulation induced contractions with significant ripple. Lower stimulation frequencies can reduce fatigue; however, they may also lead to increased ripple. Future efforts should study the relationship between force ripple and the smoothness of the evoked movements in addition to the relationship between stimulation frequency and NMES-induced fatigue to elucidate an optimal stimulation frequency for asynchronous stimulation. © 2014 Wiley Periodicals, Inc.

Aspects of computation on asynchronous parallel processors

International Nuclear Information System (INIS)

Wright, M.

1989-01-01

The increasing availability of asynchronous parallel processors has provided opportunities for original and useful work in scientific computing. However, the field of parallel computing is still in a highly volatile state, and researchers display a wide range of opinion about many fundamental questions such as models of parallelism, approaches for detecting and analyzing parallelism of algorithms, and tools that allow software developers and users to make effective use of diverse forms of complex hardware. This volume collects the work of researchers specializing in different aspects of parallel computing, who met to discuss the framework and the mechanics of numerical computing. The far-reaching impact of high-performance asynchronous systems is reflected in the wide variety of topics, which include scientific applications (e.g. linear algebra, lattice gauge simulation, ordinary and partial differential equations), models of parallelism, parallel language features, task scheduling, automatic parallelization techniques, tools for algorithm development in parallel environments, and system design issues

An Asynchronous IEEE Floating-Point Arithmetic Unit

Directory of Open Access Journals (Sweden)

Joel R. Noche

2007-12-01

Full Text Available An asynchronous floating-point arithmetic unit is designed and tested at the transistor level usingCadence software. It uses CMOS (complementary metal oxide semiconductor and DCVS (differentialcascode voltage switch logic in a 0.35 µm process using a 3.3 V supply voltage, with dual-rail data andsingle-rail control signals using four-phase handshaking.Using 17,085 transistors, the unit handles single-precision (32-bit addition/subtraction, multiplication,division, and remainder using the IEEE 754-1985 Standard for Binary Floating-Point Arithmetic, withrounding and other operations to be handled by separate hardware or software. Division and remainderare done using a restoring subtractive algorithm; multiplication uses an additive algorithm. Exceptionsare noted by flags (and not trap handlers and the output is in single-precision.Previous work on asynchronous floating-point arithmetic units have mostly focused on single operationssuch as division. This is the first work to the authors' knowledge that can perform floating-point addition,multiplication, division, and remainder using a common datapath.

Asynchronous machines. Direct torque control; Machines asynchrones. Commande par controle direct de couple

Energy Technology Data Exchange (ETDEWEB)

Fornel, B. de [Institut National Polytechnique, 31 - Toulouse (France)

2006-05-15

The asynchronous machine, with its low cost and robustness, is today the most widely used motor to make speed variators. However, its main drawback is that the same current generates both the magnetic flux and the torque, and thus any torque variation creates a flux variation. Such a coupling gives to the asynchronous machine a nonlinear behaviour which makes its control much more complex. The direct self control (DSC) method has been developed to improve the low efficiency of the scalar control method and for the specific railway drive application. The direct torque control (DTC) method is derived from the DSC method but corresponds to other type of applications. The DSC and DTC algorithms for asynchronous motors are presented in this article: 1 - direct control of the stator flux (DSC): principle, flux control, torque control, switching frequency of the inverter, speed estimation; 2 - direct torque control (DTC): principle, electromagnetic torque derivative, signals shape and switching frequency, some results, DTC speed variator without speed sensor, DTC application to multi-machine multi-converter systems; 3 - conclusion. (J.S.)

Bilingual asynchronous online discussion groups: design and delivery of an eLearning distance study module for nurse academics in a developing country.

Science.gov (United States)

Lewis, Peter A; Mai, Van Anh Thi; Gray, Genevieve

2012-04-01

The advent of eLearning has seen online discussion forums widely used in both undergraduate and postgraduate nursing education. This paper reports an Australian university experience of design, delivery and redevelopment of a distance education module developed for Vietnamese nurse academics. The teaching experience of Vietnamese nurse academics is mixed and frequently limited. It was decided that the distance module should attempt to utilise the experience of senior Vietnamese nurse academics - asynchronous online discussion groups were used to facilitate this. Online discussion occurred in both Vietnamese and English and was moderated by an Australian academic working alongside a Vietnamese translator. This paper will discuss the design of an online learning environment for foreign correspondents, the resources and translation required to maximise the success of asynchronous online discussion groups, as well as the rationale of delivering complex content in a foreign language. While specifically addressing the first iteration of the first distance module designed, this paper will also address subsequent changes made for the second iteration of the module and comment on their success. While a translator is clearly a key component of success, the elements of simplicity and clarity combined with supportive online moderation must not be overlooked. Copyright © 2011 Elsevier Ltd. All rights reserved.

An Asynchronous Multi-Sensor Micro Control Unit for Wireless Body Sensor Networks (WBSNs

Directory of Open Access Journals (Sweden)

Ching-Hsing Luo

2011-07-01

Full Text Available In this work, an asynchronous multi-sensor micro control unit (MCU core is proposed for wireless body sensor networks (WBSNs. It consists of asynchronous interfaces, a power management unit, a multi-sensor controller, a data encoder (DE, and an error correct coder (ECC. To improve the system performance and expansion abilities, the asynchronous interface is created for handshaking different clock domains between ADC and RF with MCU. To increase the use time of the WBSN system, a power management technique is developed for reducing power consumption. In addition, the multi-sensor controller is designed for detecting various biomedical signals. To prevent loss error from wireless transmission, use of an error correct coding technique is important in biomedical applications. The data encoder is added for lossless compression of various biomedical signals with a compression ratio of almost three. This design is successfully tested on a FPGA board. The VLSI architecture of this work contains 2.68-K gate counts and consumes power 496-μW at 133-MHz processing rate by using TSMC 0.13-μm CMOS process. Compared with the previous techniques, this work offers higher performance, more functions, and lower hardware cost than other micro controller designs.

How to share concurrent asynchronous wait-free variables: Preliminary version

NARCIS (Netherlands)

M. Li (Ming); P.M.B. Vitányi (Paul)

1989-01-01

textabstractWe use a structured top-down approach to develop algorithms for atomic variables shared by concurrent asynchronous wait-free processes, starting from the problem specification. By this design we obtain a better understanding of what the algorithms do, why they do it, and that they

Asynchronous communication in real space process algebra

NARCIS (Netherlands)

Baeten, J.C.M.; Bergstra, J.A.

1991-01-01

A version of classical real space process algebra is given in which messages travel with constant speed through a three-dimensional medium. It follows that communication is asynchronous and has a broadcasting character. A state operator is used to describe asynchronous message transfer and a

Asynchronous communication in real space process algebra

NARCIS (Netherlands)

Bergstra, J.A.; Baeten, J.C.M.

1992-01-01

A version of classical real space process algebra is given in which messages travel with constant speed through a three-dimensional medium. It follows that communication is asynchronous and has a broadcasting character. A state operator is used to describe asynchronous message transfer and a

Asynchronous and corrected-asynchronous numerical solutions of parabolic PDES on MIMD multiprocessors

Science.gov (United States)

Amitai, Dganit; Averbuch, Amir; Itzikowitz, Samuel; Turkel, Eli

1991-01-01

A major problem in achieving significant speed-up on parallel machines is the overhead involved with synchronizing the concurrent process. Removing the synchronization constraint has the potential of speeding up the computation. The authors present asynchronous (AS) and corrected-asynchronous (CA) finite difference schemes for the multi-dimensional heat equation. Although the discussion concentrates on the Euler scheme for the solution of the heat equation, it has the potential for being extended to other schemes and other parabolic partial differential equations (PDEs). These schemes are analyzed and implemented on the shared memory multi-user Sequent Balance machine. Numerical results for one and two dimensional problems are presented. It is shown experimentally that the synchronization penalty can be about 50 percent of run time: in most cases, the asynchronous scheme runs twice as fast as the parallel synchronous scheme. In general, the efficiency of the parallel schemes increases with processor load, with the time level, and with the problem dimension. The efficiency of the AS may reach 90 percent and over, but it provides accurate results only for steady-state values. The CA, on the other hand, is less efficient, but provides more accurate results for intermediate (non steady-state) values.

Pediatric emergency medicine asynchronous e-learning: a multicenter randomized controlled Solomon four-group study.

Science.gov (United States)

Chang, Todd P; Pham, Phung K; Sobolewski, Brad; Doughty, Cara B; Jamal, Nazreen; Kwan, Karen Y; Little, Kim; Brenkert, Timothy E; Mathison, David J

2014-08-01

Asynchronous e-learning allows for targeted teaching, particularly advantageous when bedside and didactic education is insufficient. An asynchronous e-learning curriculum has not been studied across multiple centers in the context of a clinical rotation. We hypothesize that an asynchronous e-learning curriculum during the pediatric emergency medicine (EM) rotation improves medical knowledge among residents and students across multiple participating centers. Trainees on pediatric EM rotations at four large pediatric centers from 2012 to 2013 were randomized in a Solomon four-group design. The experimental arms received an asynchronous e-learning curriculum consisting of nine Web-based, interactive, peer-reviewed Flash/HTML5 modules. Postrotation testing and in-training examination (ITE) scores quantified improvements in knowledge. A 2 × 2 analysis of covariance (ANCOVA) tested interaction and main effects, and Pearson's correlation tested associations between module usage, scores, and ITE scores. A total of 256 of 458 participants completed all study elements; 104 had access to asynchronous e-learning modules, and 152 were controls who used the current education standards. No pretest sensitization was found (p = 0.75). Use of asynchronous e-learning modules was associated with an improvement in posttest scores (p effect (partial η(2) = 0.19). Posttest scores correlated with ITE scores (r(2) = 0.14, p e-learning is an effective educational tool to improve knowledge in a clinical rotation. Web-based asynchronous e-learning is a promising modality to standardize education among multiple institutions with common curricula, particularly in clinical rotations where scheduling difficulties, seasonality, and variable experiences limit in-hospital learning. © 2014 by the Society for Academic Emergency Medicine.

CCS, locations and asynchronous transition systems

DEFF Research Database (Denmark)

Mukund, Madhavan; Nielsen, Mogens

1992-01-01

We provide a simple non-interleaved operational semantics for CCS in terms of asynchronous transition systems. We identify the concurrency present in the system in a natural way, in terms of events occurring at independent locations in the system. We extend the standard interleaving transition...... system for CCS by introducing labels on the transitions with information about the locations of events. We then show that the resulting transition system is an asynchronous transition system which has the additional property of being elementary, which means that it can also be represented by a 1-safe net....... We also introduce a notion of bisimulation on asynchronous transition systems which preserves independence. We conjecture that the induced equivalence on CCS processes coincides with the notion of location equivalence proposed by Boudol et al....

Data Collection for Mobile Group Consumption: An Asynchronous Distributed Approach

Directory of Open Access Journals (Sweden)

Weiping Zhu

2016-04-01

Full Text Available Mobile group consumption refers to consumption by a group of people, such as a couple, a family, colleagues and friends, based on mobile communications. It differs from consumption only involving individuals, because of the complex relations among group members. Existing data collection systems for mobile group consumption are centralized, which has the disadvantages of being a performance bottleneck, having single-point failure and increasing business and security risks. Moreover, these data collection systems are based on a synchronized clock, which is often unrealistic because of hardware constraints, privacy concerns or synchronization cost. In this paper, we propose the first asynchronous distributed approach to collecting data generated by mobile group consumption. We formally built a system model thereof based on asynchronous distributed communication. We then designed a simulation system for the model for which we propose a three-layer solution framework. After that, we describe how to detect the causality relation of two/three gathering events that happened in the system based on the collected data. Various definitions of causality relations based on asynchronous distributed communication are supported. Extensive simulation results show that the proposed approach is effective for data collection relating to mobile group consumption.

Data Collection for Mobile Group Consumption: An Asynchronous Distributed Approach.

Science.gov (United States)

Zhu, Weiping; Chen, Weiran; Hu, Zhejie; Li, Zuoyou; Liang, Yue; Chen, Jiaojiao

2016-04-06

Mobile group consumption refers to consumption by a group of people, such as a couple, a family, colleagues and friends, based on mobile communications. It differs from consumption only involving individuals, because of the complex relations among group members. Existing data collection systems for mobile group consumption are centralized, which has the disadvantages of being a performance bottleneck, having single-point failure and increasing business and security risks. Moreover, these data collection systems are based on a synchronized clock, which is often unrealistic because of hardware constraints, privacy concerns or synchronization cost. In this paper, we propose the first asynchronous distributed approach to collecting data generated by mobile group consumption. We formally built a system model thereof based on asynchronous distributed communication. We then designed a simulation system for the model for which we propose a three-layer solution framework. After that, we describe how to detect the causality relation of two/three gathering events that happened in the system based on the collected data. Various definitions of causality relations based on asynchronous distributed communication are supported. Extensive simulation results show that the proposed approach is effective for data collection relating to mobile group consumption.

A rapid and accurate method for determining protein content in dairy products based on asynchronous-injection alternating merging zone flow-injection spectrophotometry.

Science.gov (United States)

Liang, Qin-Qin; Li, Yong-Sheng

2013-12-01

An accurate and rapid method and a system to determine protein content using asynchronous-injection alternating merging zone flow-injection spectrophotometry based on reaction between coomassie brilliant blue G250 (CBBG) and protein was established. Main merit of our approach is that it can avoid interferences of other nitric-compounds in samples, such as melamine and urea. Optimized conditions are as follows: Concentrations of CBBG, polyvinyl alcohol (PVA), NaCl and HCl are 150 mg/l, 30 mg/l, 0.1 mol/l and 1.0% (v/v), respectively; volumes of the sample and reagent are 150 μl and 30 μl, respectively; length of a reaction coil is 200 cm; total flow rate is 2.65 ml/min. The linear range of the method is 0.5-15 mg/l (BSA), its detection limit is 0.05 mg/l, relative standard deviation is less than 1.87% (n=11), and analytical speed is 60 samples per hour. Copyright © 2013 Elsevier Ltd. All rights reserved.

Refining an asynchronous telerehabilitation platform for speech-language pathology: Engaging end-users in the process

Directory of Open Access Journals (Sweden)

Annie Jane Hill

2016-12-01

Full Text Available Asynchronous telerehabilitation in which computer-based interventions are remotely monitored and adapted offline is an emerging service delivery model in the rehabilitation of communication disorders. The asynchronous nature of this model may hold a benefit over its synchronous counterpart by eliminating scheduling issues and thus improving efficiency in a healthcare landscape of constrained resource allocation. The design of asynchronous telerehabilitation platforms should therefore ensure efficiency and flexibility. The authors have been engaged in a program of research to develop and evaluate an asynchronous telerehabilitation platform for use in speech-language pathology. eSALT is a novel asynchronous telerehabilitation platform in which clinicians design and individualize therapy tasks for upload to a client’s mobile device. An inbuilt telerehabilitation module allows for remote monitoring and updating of tasks. This paper introduces eSALT and reports outcomes from an usability study that considered the needs of two end-user groups, people with aphasia and clinicians, in the on-going refinement of eSALT. In the study participants with aphasia were paired with clinicians who used eSALT to design and customize therapy tasks. After training on the mobile device the participants engaged in therapy at home for a period of three weeks, while clinicians remotely monitored and updated tasks. Following the home trial, participants and clinicians engaged in semi-structured interviews and completed surveys on the usability of eSALT and their satisfaction with the platform. Content analysis of data involving five participants and three clinicians revealed a number of usability themes including ease of use, user support, satisfaction, limitations and potential improvements. These findings were translated into a number of refinements of the eSALT platform including the development of a client interface for use on the Apple iPad®, greater variety in

Asynchronous Parallelization of a CFD Solver

OpenAIRE

Abdi, Daniel S.; Bitsuamlak, Girma T.

2015-01-01

The article of record as published may be found at http://dx.doi.org/10.1155/2015/295393 A Navier-Stokes equations solver is parallelized to run on a cluster of computers using the domain decomposition method. Two approaches of communication and computation are investigated, namely, synchronous and asynchronous methods. Asynchronous communication between subdomains is not commonly used inCFDcodes; however, it has a potential to alleviate scaling bottlenecks incurred due to process...

Asynchronous networks: modularization of dynamics theorem

Science.gov (United States)

Bick, Christian; Field, Michael

2017-02-01

Building on the first part of this paper, we develop the theory of functional asynchronous networks. We show that a large class of functional asynchronous networks can be (uniquely) represented as feedforward networks connecting events or dynamical modules. For these networks we can give a complete description of the network function in terms of the function of the events comprising the network: the modularization of dynamics theorem. We give examples to illustrate the main results.

Asynchronous social search as a single point of access to information

NARCIS (Netherlands)

Buijs, M.P.; Spruit, M.

2017-01-01

The purpose of this paper is to present asynchronous social search as a novel and intuitive approach to search for information in which people collaborate to find the information they are looking for. Design/methodology/approach A prototype was built to test the feasibility in a business

Asynchronous SAR ADC

NARCIS (Netherlands)

2011-01-01

An asynchronous analog to digital convertor for converting an analog input signal into a digital output is presented. According to an embodiment, the analog to digital convertor comprises a clock input operable to receive an external clock signal having a clock period, a comparator operable to

Cooperative Learning in Graduate Student Projects: Comparing Synchronous versus Asynchronous Collaboration

Science.gov (United States)

Strang, Kenneth

2013-01-01

Cooperative learning was applied in a graduate project management course to compare the effectiveness of asynchronous versus synchronous online team meetings. An experiment was constructed to allocate students to project teams while ensuring there was a balance of requisite skills, namely systems analysis and design along with HTML/Javascript…

Simulating fail-stop in asynchronous distributed systems

Science.gov (United States)

Sabel, Laura; Marzullo, Keith

1994-01-01

The fail-stop failure model appears frequently in the distributed systems literature. However, in an asynchronous distributed system, the fail-stop model cannot be implemented. In particular, it is impossible to reliably detect crash failures in an asynchronous system. In this paper, we show that it is possible to specify and implement a failure model that is indistinguishable from the fail-stop model from the point of view of any process within an asynchronous system. We give necessary conditions for a failure model to be indistinguishable from the fail-stop model, and derive lower bounds on the amount of process replication needed to implement such a failure model. We present a simple one-round protocol for implementing one such failure model, which we call simulated fail-stop.

Asynchronous decentralized method for interconnected electricity markets

International Nuclear Information System (INIS)

Huang, Anni; Joo, Sung-Kwan; Song, Kyung-Bin; Kim, Jin-Ho; Lee, Kisung

2008-01-01

This paper presents an asynchronous decentralized method to solve the optimization problem of interconnected electricity markets. The proposed method decomposes the optimization problem of combined electricity markets into individual optimization problems. The impact of neighboring markets' information is included in the objective function of the individual market optimization problem by the standard Lagrangian relaxation method. Most decentralized optimization methods use synchronous models of communication to exchange updated market information among markets during the iterative process. In this paper, however, the solutions of the individual optimization problems are coordinated through an asynchronous communication model until they converge to the global optimal solution of combined markets. Numerical examples are presented to demonstrate the advantages of the proposed asynchronous method over the existing synchronous methods. (author)

Synthesis and Layout of an Asynchronous Network-on-Chip using Standard EDA Tools

DEFF Research Database (Denmark)

Müller, Christoph; Kasapaki, Evangelia; Sørensen, Rasmus Bo

2014-01-01

is the key role that clock signals play in specifying time-constraints for the synthesis. In this paper explain how we handled the synthesis and layout of an asynchronous network-on-chip for a multi-core platform. Focus is on the design process while the actual NOC-design and its performance are presented...

Introducing group-based asynchronous learning to business education : Reflections on effective course design and delivery

NARCIS (Netherlands)

Arnold, I.J.M.; Walker, R.

2004-01-01

This paper explores the contribution of virtual tools to student learning within full-time management programmes. More specifically, the paper focuses on asynchronous communication tools, considering the scope they offer for group-based collaborative learning outside the classroom. We report on the

Data Collection for Mobile Group Consumption: An Asynchronous Distributed Approach †

Science.gov (United States)

Zhu, Weiping; Chen, Weiran; Hu, Zhejie; Li, Zuoyou; Liang, Yue; Chen, Jiaojiao

2016-01-01

Mobile group consumption refers to consumption by a group of people, such as a couple, a family, colleagues and friends, based on mobile communications. It differs from consumption only involving individuals, because of the complex relations among group members. Existing data collection systems for mobile group consumption are centralized, which has the disadvantages of being a performance bottleneck, having single-point failure and increasing business and security risks. Moreover, these data collection systems are based on a synchronized clock, which is often unrealistic because of hardware constraints, privacy concerns or synchronization cost. In this paper, we propose the first asynchronous distributed approach to collecting data generated by mobile group consumption. We formally built a system model thereof based on asynchronous distributed communication. We then designed a simulation system for the model for which we propose a three-layer solution framework. After that, we describe how to detect the causality relation of two/three gathering events that happened in the system based on the collected data. Various definitions of causality relations based on asynchronous distributed communication are supported. Extensive simulation results show that the proposed approach is effective for data collection relating to mobile group consumption. PMID:27058544

Optimization of parameters of special asynchronous electric drives

Science.gov (United States)

Karandey, V. Yu; Popov, B. K.; Popova, O. B.; Afanasyev, V. L.

2018-03-01

The article considers the solution of the problem of parameters optimization of special asynchronous electric drives. The solution of the problem will allow one to project and create special asynchronous electric drives for various industries. The created types of electric drives will have optimum mass-dimensional and power parameters. It will allow one to realize and fulfill the set characteristics of management of technological processes with optimum level of expenses of electric energy, time of completing the process or other set parameters. The received decision allows one not only to solve a certain optimizing problem, but also to construct dependences between the optimized parameters of special asynchronous electric drives, for example, with the change of power, current in a winding of the stator or rotor, induction in a gap or steel of magnetic conductors and other parameters. On the constructed dependences, it is possible to choose necessary optimum values of parameters of special asynchronous electric drives and their components without carrying out repeated calculations.

Modular SoC-Design using the MANGO clockless NoC (Invited talk)

DEFF Research Database (Denmark)

Bjerregaard, Tobias; Sparsø, Jens; Mahadevan, Shankar

2005-01-01

Recent research has demonstrated the advantages of using shared, segmented interconnection networks for on-chip communication. Such on-chip networks (NoC) enable parallelism and counteract the physical effects of long wires. Network-on-Chip (NoC) thus facilitates a scalable design approach, while...... solution space to emerging SoC design challenges. In MANGO (Message-passing Asynchronous Network-on-chip providing Guaranteed services over OCP interfaces) we address issues related to a modular and scalable system-on-chip (SoC) design flow. Key features of MANGO are (i) clockless implementation......,implementation; (ii) standard socket access points based on OCP (Open Core Protocol) and (iii) guaranteed communication services. A clockless implementation promotes scalability by facilitating globally asynchronous locally synchronous (GALS) systems. GALS-type design makes the integration of cores with different...

Multiparty Asynchronous Session Types

DEFF Research Database (Denmark)

Honda, Kohei; Yoshida, Nobuko; Carbone, Marco

2016-01-01

. This work extends the foregoing theories of binary session types to multiparty, asynchronous sessions, which often arise in practical communication-centered applications. Presented as a typed calculus for mobile processes, the theory introduces a new notion of types in which interactions involving multiple......Communication is a central elements in software development. As a potential typed foundation for structured communication-centered programming, session types have been studied over the past decade for a wide range of process calculi and programming languages, focusing on binary (two-party) sessions...... peers are directly abstracted as a global scenario. Global types retain the friendly type syntax of binary session types while specifying dependencies and capturing complex causal chains of multiparty asynchronous interactions. A global type plays the role of a shared agreement among communication peers...

An Examination of Computer Engineering Students' Perceptions about Asynchronous Discussion Forums

Science.gov (United States)

Ozyurt, Ozcan; Ozyurt, Hacer

2013-01-01

This study was conducted in order to reveal the usage profiles and perceptions of Asynchronous Discussion Forums (ADFs) of 126 computer engineering students from the Computer Engineering Department in a university in Turkey. By using a mixed methods research design both quantitative and qualitative data were collected and analyzed. Research…

Interpolation algorithm for asynchronous ADC-data

Directory of Open Access Journals (Sweden)

S. Bramburger

2017-09-01

Full Text Available This paper presents a modified interpolation algorithm for signals with variable data rate from asynchronous ADCs. The Adaptive weights Conjugate gradient Toeplitz matrix (ACT algorithm is extended to operate with a continuous data stream. An additional preprocessing of data with constant and linear sections and a weighted overlap of step-by-step into spectral domain transformed signals improve the reconstruction of the asycnhronous ADC signal. The interpolation method can be used if asynchronous ADC data is fed into synchronous digital signal processing.

Asynchronous communication in real space process algebra

OpenAIRE

Baeten, JCM Jos; Bergstra, JA Jan

1990-01-01

A version of classical real space process algebra is given in which messages travel with constant speed through a three-dimensional medium. It follows that communication is asynchronous and has a broadcasting character. A state operator is used to describe asynchronous message transfer and a priority mechanism allows to express the broadcasting mechanism. As an application, a protocol is specified in which the receiver moves with respect to the sender.

Asynchronous Learning Sources in a High-Tech Organization

Science.gov (United States)

Bouhnik, Dan; Giat, Yahel; Sanderovitch, Yafit

2009-01-01

Purpose: The purpose of this study is to characterize learning from asynchronous sources among research and development (R&D) personnel. It aims to examine four aspects of asynchronous source learning: employee preferences regarding self-learning; extent of source usage; employee satisfaction with these sources and the effect of the sources on the…

TCDQ-TCT retraction and losses during asynchronous beam dump

CERN Document Server

Bracco, Chiara; Quaranta, Elena; CERN. Geneva. ATS Department

2016-01-01

The protection provided by the TCDQs in case of asynchronous beam dump depends strongly on their correct setup. They have to respect the strict hierarchy of the full collimation system and shield the tertiary collimators in the experimental regions. This MD aimed at performing asynchronous beam dump tests with different configurations, in order to assess the minimum allowed retraction between TCTs and TCDQs and, as a consequence, on the The protection provided by the TCDQs in case of asynchronous beam dump depends strongly on their correct setup. They have to respect the strict hierarchy of the full collimation system and shield the tertiary collimators in the experimental regions. This MD aimed at performing asynchronous beam dump tests with different configurations, in order to assess the minimum allowed retraction between TCTs and TCDQs and, as a consequence, on the β* reach.

Introducing Group-Based Asynchronous Learning to Business Education. Reflections on Effective Course Design and Delivery

Science.gov (United States)

Walker, Richard; Arnold, Ivo

2004-01-01

This paper explores the contribution of virtual tools to student learning within full-time management programmes. More specifically, the paper focuses on asynchronous communication tools, considering the scope they offer for group-based collaborative learning outside the classroom. We report on the effectiveness of this approach for an economics…

AP-IO: asynchronous pipeline I/O for hiding periodic output cost in CFD simulation.

Science.gov (United States)

Xiaoguang, Ren; Xinhai, Xu

2014-01-01

Computational fluid dynamics (CFD) simulation often needs to periodically output intermediate results to files in the form of snapshots for visualization or restart, which seriously impacts the performance. In this paper, we present asynchronous pipeline I/O (AP-IO) optimization scheme for the periodically snapshot output on the basis of asynchronous I/O and CFD application characteristics. In AP-IO, dedicated background I/O processes or threads are in charge of handling the file write in pipeline mode, therefore the write overhead can be hidden with more calculation than classic asynchronous I/O. We design the framework of AP-IO and implement it in OpenFOAM, providing CFD users with a user-friendly interface. Experimental results on the Tianhe-2 supercomputer demonstrate that AP-IO can achieve a good optimization effect for the periodical snapshot output in CFD application, and the effect is especially better for massively parallel CFD simulations, which can reduce the total execution time up to about 40%.

AP-IO: Asynchronous Pipeline I/O for Hiding Periodic Output Cost in CFD Simulation

Directory of Open Access Journals (Sweden)

Ren Xiaoguang

2014-01-01

Full Text Available Computational fluid dynamics (CFD simulation often needs to periodically output intermediate results to files in the form of snapshots for visualization or restart, which seriously impacts the performance. In this paper, we present asynchronous pipeline I/O (AP-IO optimization scheme for the periodically snapshot output on the basis of asynchronous I/O and CFD application characteristics. In AP-IO, dedicated background I/O processes or threads are in charge of handling the file write in pipeline mode, therefore the write overhead can be hidden with more calculation than classic asynchronous I/O. We design the framework of AP-IO and implement it in OpenFOAM, providing CFD users with a user-friendly interface. Experimental results on the Tianhe-2 supercomputer demonstrate that AP-IO can achieve a good optimization effect for the periodical snapshot output in CFD application, and the effect is especially better for massively parallel CFD simulations, which can reduce the total execution time up to about 40%.

Teleoperation system using Asynchronous transfer mode, ATM network

International Nuclear Information System (INIS)

Mohd Dani Baba; A Nasoruddin Mohamad

1999-01-01

This paper examines the application of Asynchronous Transfer Mode (ATM) in a distributed industrial environment such as in teleoperation, which performs real time control manipulation from a remote location. In our study, two models of teleoperation are proposed; the first model is a point to point connection and the second model is through an ATM network. The performance results are analysed as to determine whether the two models can support the teleoperation traffics via simulation using commercial software design tool. (Author)

Pharmacists' perception of synchronous versus asynchronous distance learning for continuing education programs.

Science.gov (United States)

Buxton, Eric C

2014-02-12

To evaluate and compare pharmacists' satisfaction with the content and learning environment of a continuing education program series offered as either synchronous or asynchronous webinars. An 8-lecture series of online presentations on the topic of new drug therapies was offered to pharmacists in synchronous and asynchronous webinar formats. Participants completed a 50-question online survey at the end of the program series to evaluate their perceptions of the distance learning experience. Eighty-two participants completed the survey instrument (41 participants from the live webinar series and 41 participants from the asynchronous webinar series.) Responses indicated that while both groups were satisfied with the program content, the asynchronous group showed greater satisfaction with many aspects of the learning environment. The synchronous and asynchronous webinar participants responded positively regarding the quality of the programming and the method of delivery, but asynchronous participants rated their experience more positively overall.

Distributed embedded controller development with petri nets application to globally-asynchronous locally-synchronous systems

CERN Document Server

Moutinho, Filipe de Carvalho

2016-01-01

This book describes a model-based development approach for globally-asynchronous locally-synchronous distributed embedded controllers.  This approach uses Petri nets as modeling formalism to create platform and network independent models supporting the use of design automation tools.  To support this development approach, the Petri nets class in use is extended with time-domains and asynchronous-channels. The authors’ approach uses models not only providing a better understanding of the distributed controller and improving the communication among the stakeholders, but also to be ready to support the entire lifecycle, including the simulation, the verification (using model-checking tools), the implementation (relying on automatic code generators), and the deployment of the distributed controller into specific platforms. Uses a graphical and intuitive modeling formalism supported by design automation tools; Enables verification, ensuring that the distributed controller was correctly specified; Provides flex...

Theoretically Based Pedagogical Strategies Leading to Deep Learning in Asynchronous Online Gerontology Courses

Science.gov (United States)

Majeski, Robin; Stover, Merrily

2007-01-01

Online learning has enjoyed increasing popularity in gerontology. This paper presents instructional strategies grounded in Fink's (2003) theory of significant learning designed for the completely asynchronous online gerontology classroom. It links these components with the development of mastery learning goals and provides specific guidelines for…

Asynchronous discrete event schemes for PDEs

Science.gov (United States)

Stone, D.; Geiger, S.; Lord, G. J.

2017-08-01

A new class of asynchronous discrete-event simulation schemes for advection-diffusion-reaction equations is introduced, based on the principle of allowing quanta of mass to pass through faces of a (regular, structured) Cartesian finite volume grid. The timescales of these events are linked to the flux on the face. The resulting schemes are self-adaptive, and local in both time and space. Experiments are performed on realistic physical systems related to porous media flow applications, including a large 3D advection diffusion equation and advection diffusion reaction systems. The results are compared to highly accurate reference solutions where the temporal evolution is computed with exponential integrator schemes using the same finite volume discretisation. This allows a reliable estimation of the solution error. Our results indicate a first order convergence of the error as a control parameter is decreased, and we outline a framework for analysis.

Exploring Asynchronous and Synchronous Tool Use in Online Courses

Science.gov (United States)

Oztok, Murat; Zingaro, Daniel; Brett, Clare; Hewitt, Jim

2013-01-01

While the independent contributions of synchronous and asynchronous interaction in online learning are clear, comparatively less is known about the pedagogical consequences of using both modes in the same environment. In this study, we examine relationships between students' use of asynchronous discussion forums and synchronous private messages…

An Overview of the Asynchronous Digital Systems – Part 3

Directory of Open Access Journals (Sweden)

Mihai Timis

2008-01-01

Full Text Available Implementation methods for the digital asynchronous systems use different predefined models like self timed circuits, speed independent circuits, delay insensitive circuits, handshake protocol implementation in asynchronous systems,C Muller circuits.

An Overview of the Asynchronous Digital Systems – Part 2

Directory of Open Access Journals (Sweden)

Mihai Timis

2008-01-01

Full Text Available Implementation methods for the digital asynchronous systems use different predefined models like self timed circuits, speed independent circuits, delay insensitive circuits, handshake protocol implementation in asynchronous systems,C Muller circuits.

Evaluation of discrete modeling efficiency of asynchronous electric machines

OpenAIRE

Byczkowska-Lipińska, Liliana; Stakhiv, Petro; Hoholyuk, Oksana; Vasylchyshyn, Ivanna

2011-01-01

In the paper the problem of effective mathematical macromodels in the form of state variables intended for asynchronous motor transient analysis is considered. Their comparing with traditional mathematical models of asynchronous motors including models built into MATLAB/Simulink software was carried out and analysis of their efficiency was conducted.

Two Studies Examining Argumentation in Asynchronous Computer Mediated Communication

Science.gov (United States)

Joiner, Richard; Jones, Sarah; Doherty, John

2008-01-01

Asynchronous computer mediated communication (CMC) would seem to be an ideal medium for supporting development in student argumentation. This paper investigates this assumption through two studies. The first study compared asynchronous CMC with face-to-face discussions. The transactional and strategic level of the argumentation (i.e. measures of…

MODELING AND INVESTIGATION OF ASYNCHRONOUS TWO-MACHINE SYSTEM MODES

Directory of Open Access Journals (Sweden)

V. S. Safaryan

2014-01-01

Full Text Available The paper considers stationary and transient processes of an asynchronous two-machine system. A mathematical model for investigation of stationary and transient modes, static characteristics and research results of dynamic process pertaining to starting-up the asynchronous two-machine system has been given in paper.

Ultra Low Energy FDSOI Asynchronous Reconfiguration Network for Adaptive Circuits

Directory of Open Access Journals (Sweden)

Soundous Chairat

2017-05-01

Full Text Available This paper introduces a plug-and-play on-chip asynchronous communication network aimed at the dynamic reconfiguration of a low-power adaptive circuit such as an internet of things (IoT system. By using a separate communication network, we can address both digital and analog blocks at a lower configuration cost, increasing the overall system power efficiency. As reconfiguration only occurs according to specific events and has to be automatically in stand-by most of the time, our design is fully asynchronous using handshake protocols. The paper presents the circuit’s architecture, performance results, and an example of the reconfiguration of frequency locked loops (FLL to validate our work. We obtain an overall energy per bit of 0.07 pJ/bit for one stage, in a 28 nm Fully Depleted Silicon On Insulator (FDSOI technology at 0.6 V and a 1.1 ns/bit latency per stage.

PsychVACS: a system for asynchronous telepsychiatry.

Science.gov (United States)

Odor, Alberto; Yellowlees, Peter; Hilty, Donald; Parish, Michelle Burke; Nafiz, Najia; Iosif, Ana-Maria

2011-05-01

To describe the technical development of an asynchronous telepsychiatry application, the Psychiatric Video Archiving and Communication System. A client-server application was developed in Visual Basic.Net with Microsoft(®) SQL database as the backend. It includes the capability of storing video-recorded psychiatric interviews and manages the workflow of the system with automated messaging. Psychiatric Video Archiving and Communication System has been used to conduct the first ever series of asynchronous telepsychiatry consultations worldwide. A review of the software application and the process as part of this project has led to a number of improvements that are being implemented in the next version, which is being written in Java. This is the first description of the use of video recorded data in an asynchronous telemedicine application. Primary care providers and consulting psychiatrists have found it easy to work with and a valuable resource to increase the availability of psychiatric consultation in remote rural locations.

An Asynchronous Time-Division-Multiplexed Network-on-Chip for Real-Time Systems

DEFF Research Database (Denmark)

Kasapaki, Evangelia

is an important part of the T-CREST paltform and used in a number of configurations. The flexible timing organization of Argo combines asynchronous routers with mesochronous NIs, which are connected to individually clocked cores, supporting a GALS system organization. The mesochronous NIs operate at the same......Multi-processor architectures using networks-on-chip (NOCs) for communication are becoming the standard approach in the development of embedded systems and general purpose platforms. Typically, multi-processor platforms follow a globally asynchronous locally synchronous (GALS) timing organization....... This thesis focuses on the design of Argo, a NOC targeted at hard real-time multi-processor platforms with a GALS timing organization. To support real-time communication, NOCs establish end-to-end connections and provide latency and throughput guarantees for these connections. Argo uses time division...

A feedback-retransmission based asynchronous frequency hopping MAC protocol for military aeronautical ad hoc networks

Directory of Open Access Journals (Sweden)

Jinhui TANG

2018-05-01

Full Text Available Attacking time-sensitive targets has rigid demands for the timeliness and reliability of information transmission, while typical Media Access Control (MAC designed for this application works well only in very light-load scenarios; as a consequence, the performances of system throughput and channel utilization are degraded. For this problem, a feedback-retransmission based asynchronous FRequency hopping Media Access (FRMA control protocol is proposed. Burst communication, asynchronous Frequency Hopping (FH, channel coding, and feedback retransmission are utilized in FRMA. With the mechanism of asynchronous FH, immediate packet transmission and multi-packet reception can be realized, and thus the timeliness is improved. Furthermore, reliability can be achieved via channel coding and feedback retransmission. With theories of queuing theory, Markov model, packets collision model, and discrete Laplace transformation, the formulas of packet success probability, system throughput, average packet end-to-end delay, and delay distribution are obtained. The approximation accuracy of theoretical derivation is verified by experimental results. Within a light-load network, the proposed FRMA has the ability of millisecond delay and 99% reliability as well as outperforms the non-feedback-retransmission based asynchronous frequency hopping media access control protocol. Keywords: Ad hoc networks, Aeronautical communications, Frequency hopping, Media Access Control (MAC, Time-sensitive

ASCERTAINMENT OF THE EQUIVALENT CIRCUIT PARAMETERS OF THE ASYNCHRONOUS MACHINE

Directory of Open Access Journals (Sweden)

V. S. Safaryan

2015-01-01

Full Text Available The article considers experimental and analytical determination of the asynchronous machine equivalent-circuit parameters with application of the reference data. Transient processes investigation of the asynchronous machines necessitates the equivalent circuit parameters (resistance impedance, inductances and coefficient of the stator-rotor contours mutual inductance that help form the transitory-process mathematical simulation model. The reference books do not provide those parameters; they instead give the rated ones (active power, voltage, slide, coefficient of performance and capacity coefficient as well as the ratio of starting and nominal currents and torques. The noted studies on the asynchronous machine equivalent-circuits parametrization fail to solve the problems ad finem or solve them with admissions. The paper presents experimental and analytical determinations of the asynchronous machine equivalent-circuit parameters: the experimental one based on the results of two measurements and the analytical one where the problem boils down to solving a system of nonlineal algebraic equations. The authors investigate the equivalent asynchronous machine input-resistance properties and adduce the dependence curvatures of the input-resistances on the slide. They present a symbolic model for analytical parameterization of the asynchronous machine equivalent-circuit that represents a system of nonlineal equations and requires one of the rotor-parameters arbitrary assignment. The article demonstrates that for the asynchronous machine equivalent-circuit experimental parameterization the measures are to be conducted of the stator-circuit voltage, current and active power with two different slides and arbitrary assignment of one of the rotor parameters. The paper substantiates the fact that additional measurement does not discard the rotor-parameter choice arbitrariness. The authors establish that in motoring mode there is a critical slide by which the

Effect of asynchronous updating on the stability of cellular automata

International Nuclear Information System (INIS)

Baetens, J.M.; Van der Weeën, P.; De Baets, B.

2012-01-01

Highlights: ► An upper bound on the Lyapunov exponent of asynchronously updated CA is established. ► The employed update method has repercussions on the stability of CAs. ► A decision on the employed update method should be taken with care. ► Substantial discrepancies arise between synchronously and asynchronously updated CA. ► Discrepancies between different asynchronous update schemes are less pronounced. - Abstract: Although cellular automata (CAs) were conceptualized as utter discrete mathematical models in which the states of all their spatial entities are updated simultaneously at every consecutive time step, i.e. synchronously, various CA-based models that rely on so-called asynchronous update methods have been constructed in order to overcome the limitations that are tied up with the classical way of evolving CAs. So far, only a few researchers have addressed the consequences of this way of updating on the evolved spatio-temporal patterns, and the reachable stationary states. In this paper, we exploit Lyapunov exponents to determine to what extent the stability of the rules within a family of totalistic CAs is affected by the underlying update method. For that purpose, we derive an upper bound on the maximum Lyapunov exponent of asynchronously iterated CAs, and show its validity, after which we present a comparative study between the Lyapunov exponents obtained for five different update methods, namely one synchronous method and four well-established asynchronous methods. It is found that the stability of CAs is seriously affected if one of the latter methods is employed, whereas the discrepancies arising between the different asynchronous methods are far less pronounced and, finally, we discuss the repercussions of our findings on the development of CA-based models.

Detection of Failure in Asynchronous Motor Using Soft Computing Method

Science.gov (United States)

Vinoth Kumar, K.; Sony, Kevin; Achenkunju John, Alan; Kuriakose, Anto; John, Ano P.

2018-04-01

This paper investigates the stator short winding failure of asynchronous motor also their effects on motor current spectrums. A fuzzy logic approach i.e., model based technique possibly will help to detect the asynchronous motor failure. Actually, fuzzy logic similar to humanoid intelligent methods besides expected linguistic empowering inferences through vague statistics. The dynamic model is technologically advanced for asynchronous motor by means of fuzzy logic classifier towards investigate the stator inter turn failure in addition open phase failure. A hardware implementation was carried out with LabVIEW for the online-monitoring of faults.

Asynchronous Operators of Sequential Logic Venjunction & Sequention

CERN Document Server

Vasyukevich, Vadim

2011-01-01

This book is dedicated to new mathematical instruments assigned for logical modeling of the memory of digital devices. The case in point is logic-dynamical operation named venjunction and venjunctive function as well as sequention and sequentional function. Venjunction and sequention operate within the framework of sequential logic. In a form of the corresponding equations, they organically fit analytical expressions of Boolean algebra. Thus, a sort of symbiosis is formed using elements of asynchronous sequential logic on the one hand and combinational logic on the other hand. So, asynchronous

Zero-Sum Flows in Designs

International Nuclear Information System (INIS)

Akbari, S.; Khosrovshahi, G.B.; Mofidi, A.

2010-07-01

Let D be a t-(v, k, λ) design and let N i (D), for 1 ≤ i ≤ t, be the higher incidence matrix of D, a (0, 1)-matrix of size (v/i) x b, where b is the number of blocks of D. A zero-sum flow of D is a nowhere-zero real vector in the null space of N 1 (D). A zero-sum k-flow of D is a zero-sum flow with values in {±,...,±(k-1)}. In this paper we show that every non-symmetric design admits an integral zero-sum flow, and consequently we conjecture that every non-symmetric design admits a zero-sum 5-flow. Similarly, the definition of zero-sum flow can be extended to N i (D), 1 ≤ i ≤ t. Let D = t-(v,k, (v-t/k-t)) be the complete design. We conjecture that N t (D) admits a zero-sum 3-flow and prove this conjecture for t = 2. (author)

[A novel proposal explaining sleep disturbance of children in Japan--asynchronization].

Science.gov (United States)

Kohyama, Jun

2008-07-01

It has been reported that more than half of the children in Japan suffer from daytime sleepiness. In contrast, about one quarter of junior high-school students in Japan complain of insomnia. According to the International Classification of Sleep Disorders (Second edition), these children could be diagnosed as having behaviorally-induced insufficient sleep syndrome due to inadequate sleeping habits. Getting on adequate amount of sleep should solve such problems;however, such a therapeutic approach often fails. Although social factors are involved in these sleep disturbances, I feel that a novel notion - asynchronization - leads to an understanding of the pathophysiology of disturbances in these children. Further, it could contribute to resolve their problems. The essence of asynchronization is a disturbance of various aspects (e.g., cycle, amplitude, phase, and interrelationship) of the biological rhythms that normally exhibits circadian oscillation. The main cause of asynchronization is hypothesized to be the combination of light exposure during night and the lack of light exposure in the morning. Asynchronization results in the disturbance of variable systems. Thus, symptoms of asynchronization include disturbances of the autonomic nervous system (sleepiness, insomnia, disturbance of hormonal excretion, gastrointestinal problems, etc.) and higher brain function (disorientation, loss of sociality, loss of will or motivation, impaired alertness and performance, etc.). Neurological (attention deficit, aggression, impulsiveness, hyperactivity, etc.), psychiatric (depressive disorders, personality disorders, anxiety disorders, etc.) and somatic (tiredness, fatigue, etc.) disturbances could also be symptoms of asynchronization. At the initial phase of asynchronization, disturbances are functional and can be resolved relatively easily, such as by the establishment of a regular sleep-wakefulness cycle;however, without adequate intervention the disturbances could gradually

Asynchronous detection of kinesthetic attention during mobilization of lower limbs using EEG measurements

Science.gov (United States)

Melinscak, Filip; Montesano, Luis; Minguez, Javier

2016-02-01

Objective. Attention is known to modulate the plasticity of the motor cortex, and plasticity is crucial for recovery in motor rehabilitation. This study addresses the possibility of using an EEG-based brain-computer interface (BCI) to detect kinesthetic attention to movement. Approach. A novel experiment emulating physical rehabilitation was designed to study kinesthetic attention. The protocol involved continuous mobilization of lower limbs during which participants reported levels of attention to movement—from focused kinesthetic attention to mind wandering. For this protocol an asynchronous BCI detector of kinesthetic attention and deliberate mind wandering was designed. Main results. EEG analysis showed significant differences in theta, alpha, and beta bands, related to the attentional state. These changes were further pinpointed to bands relative to the frequency of the individual alpha peak. The accuracy of the designed BCI ranged between 60.8% and 68.4% (significantly above chance level), depending on the used analysis window length, i.e. acceptable detection delay. Significance. This study shows it is possible to use self-reporting to study attention-related changes in EEG during continuous mobilization. Such a protocol is used to develop an asynchronous BCI detector of kinesthetic attention, with potential applications to motor rehabilitation.

Electrotechnics - AC motors. Asynchronous and brush-less motors - Lecture and exercises with solutions; Electrotechnique - Moteurs a courant alternatif. Moteurs asynchrones et brushless - Cours et problemes resolus

Energy Technology Data Exchange (ETDEWEB)

Jacob, D.

2005-07-01

This book proposes a presentation of AC electric motors essentially based on physics and technology. Its originality consists in avoiding to use mathematical formulations (like Park's transformation). The modeling retained, which only uses magnetic momentum, magnetic fields and reluctance concepts, leads simply and naturally to the vectorial control principle. The book develops some lecture elements which includes some topics rarely considered like the dimensioning of an asynchronous motor or of a single-phase brush-less motor. Experimental results illustrate the physical phenomena described and many original problems are resolved and commented at the end of each chapter. Content: signals and systems in electrotechnics, torque and rotating magnetic fields generation, asynchronous machine in permanent regime, speed variation of the asynchronous motor, special asynchronous motors, synchronous machine in permanent regime, brush-less motor, note about step motors, note about inverters, index. (J.S.)

Asynchronous sampled-data approach for event-triggered systems

Science.gov (United States)

Mahmoud, Magdi S.; Memon, Azhar M.

2017-11-01

While aperiodically triggered network control systems save a considerable amount of communication bandwidth, they also pose challenges such as coupling between control and event-condition design, optimisation of the available resources such as control, communication and computation power, and time-delays due to computation and communication network. With this motivation, the paper presents separate designs of control and event-triggering mechanism, thus simplifying the overall analysis, asynchronous linear quadratic Gaussian controller which tackles delays and aperiodic nature of transmissions, and a novel event mechanism which compares the cost of the aperiodic system against a reference periodic implementation. The proposed scheme is simulated on a linearised wind turbine model for pitch angle control and the results show significant improvement against the periodic counterpart.

Behavioral Synthesis of Asynchronous Circuits Using Syntax Directed Translation as Backend

DEFF Research Database (Denmark)

Nielsen, Sune Fallgaard; Sparsø, Jens; Madsen, Jan

2009-01-01

The current state-of-the art in high-level synthesis of asynchronous circuits is syntax directed translation, which performs a one-to-one mapping of a HDL-description into a corresponding circuit. This paper presents a method for behavioral synthesis of asynchronous circuits which builds on top...... description language Balsa [1]. This ”conventional” template architecture allows us to adapt traditional synchronous synthesis techniques for resource sharing, scheduling, binding etc, to the domain of asynchronous circuits. A prototype tool has been implemented on top of the Balsa framework, and the method...... is illustrated through the implementation of a set of example circuits. The main contributions of the paper are: the fundamental idea, the template architecture and its implementation using asynchronous handshake components, and the implementation of a prototype tool....

Dynamic modeling of an asynchronous squirrel-cage machine; Modelisation dynamique d'une machine asynchrone a cage

Energy Technology Data Exchange (ETDEWEB)

Guerette, D.

2009-07-01

This document presented a detailed mathematical explanation and validation of the steps leading to the development of an asynchronous squirrel-cage machine. The MatLab/Simulink software was used to model a wind turbine at variable high speeds. The asynchronous squirrel-cage machine is an electromechanical system coupled to a magnetic circuit. The resulting electromagnetic circuit can be represented as a set of resistances, leakage inductances and mutual inductances. Different models were used for a comparison study, including the Munteanu, Boldea, Wind Turbine Blockset, and SimPowerSystem. MatLab/Simulink modeling results were in good agreement with the results from other comparable models. Simulation results were in good agreement with analytical calculations. 6 refs, 2 tabs, 9 figs.

Asynchronous and Synchronous Online Discussion: Real and Perceived Achievement Differences

Science.gov (United States)

Johnson, Genevieve Marie; Buck, George H.

2007-01-01

Students in an introductory educational psychology course used two WebCT communication tools (synchronous chat and asynchronous discussion) to discuss four case studies. In response to the item, "I learned the case studies best when using," 39 students selected synchronous chat and 51 students selected asynchronous discussion. Students who…

Asynchronous cracking with dissimilar paths in multilayer graphene.

Science.gov (United States)

Jang, Bongkyun; Kim, Byungwoon; Kim, Jae-Hyun; Lee, Hak-Joo; Sumigawa, Takashi; Kitamura, Takayuki

2017-11-16

Multilayer graphene consists of a stack of single-atomic-thick monolayer graphene sheets bound with π-π interactions and is a fascinating model material opening up a new field of fracture mechanics. In this study, fracture behavior of single-crystalline multilayer graphene was investigated using an in situ mode I fracture test under a scanning electron microscope, and abnormal crack propagation in multilayer graphene was identified for the first time. The fracture toughness of graphene was determined from the measured load-displacement curves and the realistic finite element modelling of specimen geometries. Nonlinear fracture behavior of the multilayer graphene is discussed based on nonlinear elastic fracture mechanics. In situ scanning electron microscope images obtained during the fracture test showed asynchronous crack propagation along independent paths, causing interlayer shear stress and slippages. We also found that energy dissipation by interlayer slippages between the graphene layers is the reason for the enhanced fracture toughness of multilayer graphene. The asynchronous cracking with independent paths is a unique cracking and toughening mechanism for single-crystalline multilayer graphene, which is not observed for the monolayer graphene. This could provide a useful insight for the design and development of graphene-based composite materials for structural applications.

Handbook of asynchronous machines with variable speed

CERN Document Server

Razik, Hubert

2013-01-01

This handbook deals with the asynchronous machine in its close environment. It was born from a reflection on this electromagnetic converter whose integration in industrial environments takes a wide part. Previously this type of motor operated at fixed speed, from now on it has been integrated more and more in processes at variable speed. For this reason it seemed useful, or necessary, to write a handbook on the various aspects from the motor in itself, via the control and while finishing by the diagnosis aspect. Indeed, an asynchronous motor is used nowadays in industry where variation speed a

Reliable self-replicating machines in asynchronous cellular automata.

Science.gov (United States)

Lee, Jia; Adachi, Susumu; Peper, Ferdinand

2007-01-01

We propose a self-replicating machine that is embedded in a two-dimensional asynchronous cellular automaton with von Neumann neighborhood. The machine dynamically encodes its shape into description signals, and despite the randomness of cell updating, it is able to successfully construct copies of itself according to the description signals. Self-replication on asynchronously updated cellular automata may find application in nanocomputers, where reconfigurability is an essential property, since it allows avoidance of defective parts and simplifies programming of such computers.

Functional asynchronous networks: Factorization of dynamics and function

Directory of Open Access Journals (Sweden)

Bick Christian

2016-01-01

Full Text Available In this note we describe the theory of functional asynchronous networks and one of the main results, the Modularization of Dynamics Theorem, which for a large class of functional asynchronous networks gives a factorization of dynamics in terms of constituent subnetworks. For these networks we can give a complete description of the network function in terms of the function of the events comprising the network and thereby answer a question originally raised by Alon in the context of biological networks.

Toward Personal and Emotional Connectivity in Mobile Higher Education through Asynchronous Formative Audio Feedback

Science.gov (United States)

Rasi, Päivi; Vuojärvi, Hanna

2018-01-01

This study aims to develop asynchronous formative audio feedback practices for mobile learning in higher education settings. The development was conducted in keeping with the principles of design-based research. The research activities focused on an inter-university online course, within which the use of instructor audio feedback was tested,…

Application of intelligent soft start in asynchronous motor

Science.gov (United States)

Du, Xue; Ye, Ying; Wang, Yuelong; Peng, Lei; Zhang, Suying

2018-05-01

The starting way of three phase asynchronous motor has full voltage start and step-down start. Direct starting brings large current impact, causing excessive local temperature to the power grid and larger starting torque will also impact the motor equipment and affect the service life of the motor. Aim at the problem of large current and torque caused by start-up, an intelligent soft starter is proposed. Through the application of intelligent soft start on asynchronous motor, highlights its application advantage in motor control.

Distributed Consensus of Stochastic Delayed Multi-agent Systems Under Asynchronous Switching.

Science.gov (United States)

Wu, Xiaotai; Tang, Yang; Cao, Jinde; Zhang, Wenbing

2016-08-01

In this paper, the distributed exponential consensus of stochastic delayed multi-agent systems with nonlinear dynamics is investigated under asynchronous switching. The asynchronous switching considered here is to account for the time of identifying the active modes of multi-agent systems. After receipt of confirmation of mode's switching, the matched controller can be applied, which means that the switching time of the matched controller in each node usually lags behind that of system switching. In order to handle the coexistence of switched signals and stochastic disturbances, a comparison principle of stochastic switched delayed systems is first proved. By means of this extended comparison principle, several easy to verified conditions for the existence of an asynchronously switched distributed controller are derived such that stochastic delayed multi-agent systems with asynchronous switching and nonlinear dynamics can achieve global exponential consensus. Two examples are given to illustrate the effectiveness of the proposed method.

The Determination of the Asynchronous Traction Motor Characteristics of Locomotive

Directory of Open Access Journals (Sweden)

Pavel Grigorievich Kolpakhchyan

2017-01-01

Full Text Available The article deals with the problem of the locomotive asynchronous traction motor control with the AC diesel-electric transmission. The limitations of the torque of the traction motor when powered by the inverter are determined. The recommendations to improve the use of asynchronous traction motor of locomotives with the AC diesel-electric transmission are given.

OFDM with Index Modulation for Asynchronous mMTC Networks.

Science.gov (United States)

Doğan, Seda; Tusha, Armed; Arslan, Hüseyin

2018-04-21

One of the critical missions for next-generation wireless communication systems is to fulfill the high demand for massive Machine-Type Communications (mMTC). In mMTC systems, a sporadic transmission is performed between machine users and base station (BS). Lack of coordination between the users and BS in time destroys orthogonality between the subcarriers, and causes inter-carrier interference (ICI). Therefore, providing services to asynchronous massive machine users is a major challenge for Orthogonal Frequency Division Multiplexing (OFDM). In this study, OFDM with index modulation (OFDM-IM) is proposed as an eligible solution to alleviate ICI caused by asynchronous transmission in uncoordinated mMTC networks. In OFDM-IM, data transmission is performed not only by modulated subcarriers but also by the indices of active subcarriers. Unlike classical OFDM, fractional subcarrier activation leads to less ICI in OFDM-IM technology. A novel subcarrier mapping scheme (SMS) named as Inner Subcarrier Activation is proposed to further alleviate adjacent user interference in asynchronous OFDM-IM-based systems. ISA reduces inter-user interference since it gives more activation priority to inner subcarriers compared with the existing SMS-s. The superiority of the proposed SMS is shown through both theoretical analysis and computer-based simulations in comparison to existing mapping schemes for asynchronous systems.

Asynchronous control for networked systems

CERN Document Server

Rubio, Francisco; Bencomo, Sebastián

2015-01-01

This book sheds light on networked control systems; it describes different techniques for asynchronous control, moving away from the periodic actions of classical control, replacing them with state-based decisions and reducing the frequency with which communication between subsystems is required. The text focuses specially on event-based control. Split into two parts, Asynchronous Control for Networked Systems begins by addressing the problems of single-loop networked control systems, laying out various solutions which include two alternative model-based control schemes (anticipatory and predictive) and the use of H2/H∞ robust control to deal with network delays and packet losses. Results on self-triggering and send-on-delta sampling are presented to reduce the need for feedback in the loop. In Part II, the authors present solutions for distributed estimation and control. They deal first with reliable networks and then extend their results to scenarios in which delays and packet losses may occur. The novel ...

Comparing face-to-face, synchronous, and asynchronous learning: postgraduate dental resident preferences.

Science.gov (United States)

Kunin, Marc; Julliard, Kell N; Rodriguez, Tobias E

2014-06-01

The Department of Dental Medicine of Lutheran Medical Center has developed an asynchronous online curriculum consisting of prerecorded PowerPoint presentations with audio explanations. The focus of this study was to evaluate if the new asynchronous format satisfied the educational needs of the residents compared to traditional lecture (face-to-face) and synchronous (distance learning) formats. Lectures were delivered to 219 dental residents employing face-to-face and synchronous formats, as well as the new asynchronous format; 169 (77 percent) participated in the study. Outcomes were assessed with pretests, posttests, and individual lecture surveys. Results found the residents preferred face-to-face and asynchronous formats to the synchronous format in terms of effectiveness and clarity of presentations. This preference was directly related to the residents' perception of how well the technology worked in each format. The residents also rated the quality of student-instructor and student-student interactions in the synchronous and asynchronous formats significantly higher after taking the lecture series than they did before taking it. However, they rated the face-to-face format as significantly more conducive to student-instructor and student-student interaction. While the study found technology had a major impact on the efficacy of this curricular model, the results suggest that the asynchronous format can be an effective way to teach a postgraduate course.

Effects of Asynchronous Music on Students' Lesson Satisfaction and Motivation at the Situational Level

Science.gov (United States)

Digelidis, Nikolaos; Karageorghis, Costas I.; Papapavlou, Anastasia; Papaioannou, Athanasios G.

2014-01-01

The aim of this study was to examine the effects of asynchronous (background) music on senior students' motivation and lesson satisfaction at the situational level. A counterbalanced mixed-model design was employed with two factors comprising condition (three levels) and gender (two levels). Two hundred students (82 boys, 118 girls; M [subscript…

Supporting collaborative discussions on asynchronous time: a technological perspective

OpenAIRE

Caballé, Santi

2011-01-01

The aim of this paper is to report on an experience of using an innovative on-line learning tool to support real, collaborative learning through discussion in asynchronous time. While asynchronous interaction gives rise to unique opportunities that support active, collaborative learning, unique problems also arise, such as frustration, caused by waiting for other peoples' reactions and feedback and the consequent loss of motivation, which has a negative impact on learning outcomes. In order t...

EPOS for Coordination of Asynchronous Sensor Webs

Data.gov (United States)

National Aeronautics and Space Administration — Develop, integrate, and deploy software-based tools to coordinate asynchronous, distributed missions and optimize observation planning spanning simultaneous...

Multithreaded Asynchronous Graph Traversal for In-Memory and Semi-External Memory

KAUST Repository

Pearce, Roger

2010-11-01

Processing large graphs is becoming increasingly important for many domains such as social networks, bioinformatics, etc. Unfortunately, many algorithms and implementations do not scale with increasing graph sizes. As a result, researchers have attempted to meet the growing data demands using parallel and external memory techniques. We present a novel asynchronous approach to compute Breadth-First-Search (BFS), Single-Source-Shortest-Paths, and Connected Components for large graphs in shared memory. Our highly parallel asynchronous approach hides data latency due to both poor locality and delays in the underlying graph data storage. We present an experimental study applying our technique to both In-Memory and Semi-External Memory graphs utilizing multi-core processors and solid-state memory devices. Our experiments using synthetic and real-world datasets show that our asynchronous approach is able to overcome data latencies and provide significant speedup over alternative approaches. For example, on billion vertex graphs our asynchronous BFS scales up to 14x on 16-cores. © 2010 IEEE.

A prototype pixel readout chip for asynchronous detection applications

International Nuclear Information System (INIS)

Raymond, D.M.; Hall, G.; Lewis, A.J.; Sharp, P.H.

1991-01-01

A two-dimensional array of amplifier cells has been fabricated as a prototype readout system for a matching array of silicon diode detectors. Each cell contains a preamplifier, shaping amplifier, comparator and analogue signal storage in an area of 300 μmx320 μm using 3 μm CMOS technology. Full size chips will be bump bonded to pixel detector arrays. Low noise and asynchronous operation are novel design features. With noise levels of less than 250 rms electrons for input capacitances up to 600 fF, pixel detectors will be suitable for autoradiography, synchrotron X-ray and high energy particle detection applications. The design of the prototype chip is presented and future developments and prospects for applications are discussed. (orig.)

A Block-Asynchronous Relaxation Method for Graphics Processing Units

OpenAIRE

Anzt, H.; Dongarra, J.; Heuveline, Vincent; Tomov, S.

2011-01-01

In this paper, we analyze the potential of asynchronous relaxation methods on Graphics Processing Units (GPUs). For this purpose, we developed a set of asynchronous iteration algorithms in CUDA and compared them with a parallel implementation of synchronous relaxation methods on CPU-based systems. For a set of test matrices taken from the University of Florida Matrix Collection we monitor the convergence behavior, the average iteration time and the total time-to-solution time. Analyzing the r...

Design of Distributed Controllers Seeking Optimal Power Flow Solutions Under Communication Constraints

Energy Technology Data Exchange (ETDEWEB)

Dall' Anese, Emiliano; Simonetto, Andrea; Dhople, Sairaj

2016-12-29

This paper focuses on power distribution networks featuring inverter-interfaced distributed energy resources (DERs), and develops feedback controllers that drive the DER output powers to solutions of time-varying AC optimal power flow (OPF) problems. Control synthesis is grounded on primal-dual-type methods for regularized Lagrangian functions, as well as linear approximations of the AC power-flow equations. Convergence and OPF-solution-tracking capabilities are established while acknowledging: i) communication-packet losses, and ii) partial updates of control signals. The latter case is particularly relevant since it enables asynchronous operation of the controllers where DER setpoints are updated at a fast time scale based on local voltage measurements, and information on the network state is utilized if and when available, based on communication constraints. As an application, the paper considers distribution systems with high photovoltaic integration, and demonstrates that the proposed framework provides fast voltage-regulation capabilities, while enabling the near real-time pursuit of solutions of AC OPF problems.

Conditions for Model Matching of Switched Asynchronous Sequential Machines with Output Feedback

OpenAIRE

Jung–Min Yang

2016-01-01

Solvability of the model matching problem for input/output switched asynchronous sequential machines is discussed in this paper. The control objective is to determine the existence condition and design algorithm for a corrective controller that can match the stable-state behavior of the closed-loop system to that of a reference model. Switching operations and correction procedures are incorporated using output feedback so that the controlled switched machine can show the ...

Non-fragile switched H∞ control for morphing aircraft with asynchronous switching

Directory of Open Access Journals (Sweden)

Haoyu CHENG

2017-06-01

Full Text Available This paper deals with the problem of non-fragile linear parameter-varying (LPV H∞ control for morphing aircraft with asynchronous switching. The switched LPV model of morphing aircraft is established by Jacobian linearization approach according to the nonlinear model. The data missing is taken into account in the link from sensors to controllers and the link from controllers to actuators, which satisfies Bernoulli distribution. The non-fragile switched LPV controllers are constructed with consideration of the uncertainties of controllers and asynchronous switching phenomenon. The parameter-dependent Lyapunov functional method and mode-dependent average dwell time (MDADT method are combined to guarantee the stability and prescribed performance of the system. The sufficient conditions on the solvability of the problem are derived in the form of linear matrix inequalities (LMI. In order to achieve higher efficiency of the designing process, an algorithm is applied to divide the whole set into subsets automatically. Simulation results are provided to verify the effectiveness and superiority of the method in the paper.

A Synchronous-Asynchronous Particle Swarm Optimisation Algorithm

Science.gov (United States)

Ab Aziz, Nor Azlina; Mubin, Marizan; Mohamad, Mohd Saberi; Ab Aziz, Kamarulzaman

2014-01-01

In the original particle swarm optimisation (PSO) algorithm, the particles' velocities and positions are updated after the whole swarm performance is evaluated. This algorithm is also known as synchronous PSO (S-PSO). The strength of this update method is in the exploitation of the information. Asynchronous update PSO (A-PSO) has been proposed as an alternative to S-PSO. A particle in A-PSO updates its velocity and position as soon as its own performance has been evaluated. Hence, particles are updated using partial information, leading to stronger exploration. In this paper, we attempt to improve PSO by merging both update methods to utilise the strengths of both methods. The proposed synchronous-asynchronous PSO (SA-PSO) algorithm divides the particles into smaller groups. The best member of a group and the swarm's best are chosen to lead the search. Members within a group are updated synchronously, while the groups themselves are asynchronously updated. Five well-known unimodal functions, four multimodal functions, and a real world optimisation problem are used to study the performance of SA-PSO, which is compared with the performances of S-PSO and A-PSO. The results are statistically analysed and show that the proposed SA-PSO has performed consistently well. PMID:25121109

Asynchronous and synchronous dual-wavelength pulse generation in a passively mode-locked fiber laser with a mode-locker.

Science.gov (United States)

Hu, Guoqing; Pan, Yingling; Zhao, Xin; Yin, Siyao; Zhang, Meng; Zheng, Zheng

2017-12-01

The evolution from asynchronous to synchronous dual-wavelength pulse generation in a passively mode-locked fiber laser is experimentally investigated by tailoring the intracavity dispersion. Through tuning the intracavity-loss-dependent gain profile and the birefringence-induced filter effect, asynchronous dual-wavelength soliton pulses can be generated until the intracavity anomalous dispersion is reduced to ∼8  fs/nm. The transition from asynchronous to synchronous pulse generation is then observed at an elevated pump power in the presence of residual anomalous dispersion, and it is shown that pulses are temporally synchronized at the mode-locker in the cavity. Spectral sidelobes are observed and could be attributed to the four-wave-mixing effect between dual-wavelength pulses at the carbon nanotube mode-locker. These results could provide further insight into the design and realization of such dual-wavelength ultrafast lasers for different applications such as dual-comb metrology as well as better understanding of the inter-pulse interactions in such dual-comb lasers.

Asynchronous CMC, Collaboration and the Development of Critical Thinking in a Graduate Seminar in Applied Linguistics

Science.gov (United States)

Abrams, Zsuzsanna I.

2005-01-01

A primary objective of graduate education, and often promoted by peer collaboration tasks, is the development of critical thinking skills. The present study compares how graduate students enrolled in a qualitative research design course in applied linguistics utilized asynchronous computer-mediated communication (ACMC) and face-to-face…

Network evolution induced by asynchronous stimuli through spike-timing-dependent plasticity.

Directory of Open Access Journals (Sweden)

Wu-Jie Yuan

Full Text Available In sensory neural system, external asynchronous stimuli play an important role in perceptual learning, associative memory and map development. However, the organization of structure and dynamics of neural networks induced by external asynchronous stimuli are not well understood. Spike-timing-dependent plasticity (STDP is a typical synaptic plasticity that has been extensively found in the sensory systems and that has received much theoretical attention. This synaptic plasticity is highly sensitive to correlations between pre- and postsynaptic firings. Thus, STDP is expected to play an important role in response to external asynchronous stimuli, which can induce segregative pre- and postsynaptic firings. In this paper, we study the impact of external asynchronous stimuli on the organization of structure and dynamics of neural networks through STDP. We construct a two-dimensional spatial neural network model with local connectivity and sparseness, and use external currents to stimulate alternately on different spatial layers. The adopted external currents imposed alternately on spatial layers can be here regarded as external asynchronous stimuli. Through extensive numerical simulations, we focus on the effects of stimulus number and inter-stimulus timing on synaptic connecting weights and the property of propagation dynamics in the resulting network structure. Interestingly, the resulting feedforward structure induced by stimulus-dependent asynchronous firings and its propagation dynamics reflect both the underlying property of STDP. The results imply a possible important role of STDP in generating feedforward structure and collective propagation activity required for experience-dependent map plasticity in developing in vivo sensory pathways and cortices. The relevance of the results to cue-triggered recall of learned temporal sequences, an important cognitive function, is briefly discussed as well. Furthermore, this finding suggests a potential

MED5/355: Using Web-technology for Asynchronous Telemedicine Consulting

OpenAIRE

Reviakin, Y; Sukhanov, A

1999-01-01

Introduction Common telemedicine consultations can be divided in two classes: real-time telemedicine consultations and asynchronous telemedicine consultations. The advantage of real-time consultations is obvious - this is a natural discussion between physicians, which may be realised on the basis of desktop videoconferences. But the problems are also obvious: the necessity of additional hardware and the elevated demands for channel bandwidth. Because of the latter, the use of asynchronous tel...

Using Television Sitcoms to Facilitate Asynchronous Discussions in the Online Communication Course

Science.gov (United States)

Tolman, Elizabeth; Asbury, Bryan

2012-01-01

Asynchronous discussions are a useful instructional resource in the online communication course. In discussion groups students have the opportunity to actively participate and interact with students and the instructor. Asynchronous communication allows for flexibility because "participants can interact with significant amounts of time between…

[Cost-effectiveness of Synchronous vs. Asynchronous Telepsychiatry in Prison Inmates With Depression].

Science.gov (United States)

Barrera-Valencia, Camilo; Benito-Devia, Alexis Vladimir; Vélez-Álvarez, Consuelo; Figueroa-Barrera, Mario; Franco-Idárraga, Sandra Milena

Telepsychiatry is defined as the use of information and communication technology (ICT) in providing remote psychiatric services. Telepsychiatry is applied using two types of communication: synchronous (real time) and asynchronous (store and forward). To determine the cost-effectiveness of a synchronous and an asynchronous telepsychiatric model in prison inmate patients with symptoms of depression. A cost-effectiveness study was performed on a population consisting of 157 patients from the Establecimiento Penitenciario y Carcelario de Mediana Seguridad de Manizales, Colombia. The sample was determined by applying Zung self-administered surveys for depression (1965) and the Hamilton Depression Rating Scale (HDRS), the latter being the tool used for the comparison. Initial Hamilton score, arrival time, duration of system downtime, and clinical effectiveness variables had normal distributions (P>.05). There were significant differences (P<.001) between care costs for the different models, showing that the mean cost of the asynchronous model is less than synchronous model, and making the asynchronous model more cost-effective. The asynchronous model is the most cost-effective model of telepsychiatry care for patients with depression admitted to a detention centre, according to the results of clinical effectiveness, cost measurement, and patient satisfaction. Copyright © 2016 Asociación Colombiana de Psiquiatría. Publicado por Elsevier España. All rights reserved.

RESEARCH INTO VALVE-ENGINE TRANSDUCERS OF BRUSHLESS SYNCHRONOUS AND ASYNCHRONIZED MACHINES IN A CIRCUIT SIMULATION SYSTEM.

Directory of Open Access Journals (Sweden)

A.M. Galynovskiy

2013-10-01

Full Text Available Designing features for valve-engine transducers of brushless synchronous and asynchronized machines are described. Global analysis of research results on the transducer models in a MicroCap circuit simulation system is made, recommendations on the simulation system application in both scientific research and educational process given.

Asynchronous anti-noise hyper chaotic secure communication system based on dynamic delay and state variables switching

Energy Technology Data Exchange (ETDEWEB)

Liu, Hongjun [Faculty of Electronic Information and Electrical Engineering, Dalian University of Technology, Dalian 116024 (China); Weifang Vocational College, Weifang 261041 (China); Wang, Xingyuan, E-mail: wangxy@dlut.edu.cn [Faculty of Electronic Information and Electrical Engineering, Dalian University of Technology, Dalian 116024 (China); Zhu, Quanlong [Faculty of Electronic Information and Electrical Engineering, Dalian University of Technology, Dalian 116024 (China)

2011-07-18

This Letter designs an asynchronous hyper chaotic secure communication system, which possesses high stability against noise, using dynamic delay and state variables switching to ensure the high security. The relationship between the bit error ratio (BER) and the signal-to-noise ratio (SNR) is analyzed by simulation tests, the results show that the BER can be ensured to reach zero by proportionally adjusting the amplitudes of the state variables and the noise figure. The modules of the transmitter and receiver are implemented, and numerical simulations demonstrate the effectiveness of the system. -- Highlights: → Asynchronous anti-noise hyper chaotic secure communication system. → Dynamic delay and state switching to ensure the high security. → BER can reach zero by adjusting the amplitudes of state variables and noise figure.

Sensor placement on Canton Tower for health monitoring using asynchronous-climb monkey algorithm

Science.gov (United States)

Yi, Ting-Hua; Li, Hong-Nan; Zhang, Xu-Dong

2012-12-01

Heuristic optimization algorithms have become a popular choice for solving complex and intricate sensor placement problems which are difficult to solve by traditional methods. This paper proposes a novel and interesting methodology called the asynchronous-climb monkey algorithm (AMA) for the optimum design of sensor arrays for a structural health monitoring system. Different from the existing algorithms, the dual-structure coding method is designed and adopted for the representation of the design variables. The asynchronous-climb process is incorporated in the proposed AMA that can adjust the trajectory of each individual dynamically in the search space according to its own experience and other monkeys. The concept of ‘monkey king’ is introduced in the AMA, which reflects the Darwinian principle of natural selection and can create an interaction network to correctly guide the movement of other monkeys. Numerical experiments are carried out using two different objective functions by considering the Canton Tower in China with or without the antenna mast to evaluate the performance of the proposed algorithm. Investigations have indicated that the proposed AMA exhibits faster convergence characteristics and can generate sensor configurations superior in all instances when compared to the conventional monkey algorithm. For structures with stiffness mutation such as the Canton Tower, the sensor placement needs to be considered for each part separately.

Sensor placement on Canton Tower for health monitoring using asynchronous-climb monkey algorithm

International Nuclear Information System (INIS)

Yi, Ting-Hua; Li, Hong-Nan; Zhang, Xu-Dong

2012-01-01

Heuristic optimization algorithms have become a popular choice for solving complex and intricate sensor placement problems which are difficult to solve by traditional methods. This paper proposes a novel and interesting methodology called the asynchronous-climb monkey algorithm (AMA) for the optimum design of sensor arrays for a structural health monitoring system. Different from the existing algorithms, the dual-structure coding method is designed and adopted for the representation of the design variables. The asynchronous-climb process is incorporated in the proposed AMA that can adjust the trajectory of each individual dynamically in the search space according to its own experience and other monkeys. The concept of ‘monkey king’ is introduced in the AMA, which reflects the Darwinian principle of natural selection and can create an interaction network to correctly guide the movement of other monkeys. Numerical experiments are carried out using two different objective functions by considering the Canton Tower in China with or without the antenna mast to evaluate the performance of the proposed algorithm. Investigations have indicated that the proposed AMA exhibits faster convergence characteristics and can generate sensor configurations superior in all instances when compared to the conventional monkey algorithm. For structures with stiffness mutation such as the Canton Tower, the sensor placement needs to be considered for each part separately. (paper)

On the Convergence of Asynchronous Parallel Pattern Search

International Nuclear Information System (INIS)

Tamara Gilbson Kolda

2002-01-01

In this paper the authors prove global convergence for asynchronous parallel pattern search. In standard pattern search, decisions regarding the update of the iterate and the step-length control parameter are synchronized implicitly across all search directions. They lose this feature in asynchronous parallel pattern search since the search along each direction proceeds semi-autonomously. By bounding the value of the step-length control parameter after any step that produces decrease along a single search direction, they can prove that all the processes share a common accumulation point and that such a point is a stationary point of the standard nonlinear unconstrained optimization problem

ZONES OF STEADY CAPACITOR EXCITATION IN A MODE OF GENERATION OF TYPICAL ASYNCHRONOUS MACHINES

Directory of Open Access Journals (Sweden)

Postoronca Sv.

2009-12-01

Full Text Available In work some features of a mode of capacitor excitation of industrial asynchronous electric motors, and also generators made on their base which can be used in wind installations of low power are considered. Borders of zones of steady capacitor excitation of asynchronous electric motors in rated power of 0,25-22,0 kW and generators made on their base, and also character of influence of own losses and active capacity of loading of the equivalent circuit of the asynchronous machine resulted in parameters have been determined. Some recommendations after maintenance of stability of capacitor excitation of asynchronous machines for work in a mode of generation of electric energy are given.

Gigabit Ethernet signal transmission using asynchronous optical code division multiple access.

Science.gov (United States)

Ma, Philip Y; Fok, Mable P; Shastri, Bhavin J; Wu, Ben; Prucnal, Paul R

2015-12-15

We propose and experimentally demonstrate a novel architecture for interfacing and transmitting a Gigabit Ethernet (GbE) signal using asynchronous incoherent optical code division multiple access (OCDMA). This is the first such asynchronous incoherent OCDMA system carrying GbE data being demonstrated to be working among multi-users where each user is operating with an independent clock/data rate and is granted random access to the network. Three major components, the GbE interface, the OCDMA transmitter, and the OCDMA receiver are discussed in detail. The performance of the system is studied and characterized through measuring eye diagrams, bit-error rate and packet loss rate in real-time file transfer. Our Letter also addresses the near-far problem and realizes asynchronous transmission and detection of signal.

Asynchronous vs didactic education: it's too early to throw in the towel on tradition.

Science.gov (United States)

Jordan, Jaime; Jalali, Azadeh; Clarke, Samuel; Dyne, Pamela; Spector, Tahlia; Coates, Wendy

2013-08-08

Asynchronous, computer based instruction is cost effective, allows self-directed pacing and review, and addresses preferences of millennial learners. Current research suggests there is no significant difference in learning compared to traditional classroom instruction. Data are limited for novice learners in emergency medicine. The objective of this study was to compare asynchronous, computer-based instruction with traditional didactics for senior medical students during a week-long intensive course in acute care. We hypothesized both modalities would be equivalent. This was a prospective observational quasi-experimental study of 4th year medical students who were novice learners with minimal prior exposure to curricular elements. We assessed baseline knowledge with an objective pre-test. The curriculum was delivered in either traditional lecture format (shock, acute abdomen, dyspnea, field trauma) or via asynchronous, computer-based modules (chest pain, EKG interpretation, pain management, trauma). An interactive review covering all topics was followed by a post-test. Knowledge retention was measured after 10 weeks. Pre and post-test items were written by a panel of medical educators and validated with a reference group of learners. Mean scores were analyzed using dependent t-test and attitudes were assessed by a 5-point Likert scale. 44 of 48 students completed the protocol. Students initially acquired more knowledge from didactic education as demonstrated by mean gain scores (didactic: 28.39% ± 18.06; asynchronous 9.93% ± 23.22). Mean difference between didactic and asynchronous = 18.45% with 95% CI [10.40 to 26.50]; p = 0.0001. Retention testing demonstrated similar knowledge attrition: mean gain scores -14.94% (didactic); -17.61% (asynchronous), which was not significantly different: 2.68% ± 20.85, 95% CI [-3.66 to 9.02], p = 0.399. The attitudinal survey revealed that 60.4% of students believed the asynchronous modules were educational and 95

Design of Distributed Controllers Seeking Optimal Power Flow Solutions under Communication Constraints: Preprint

Energy Technology Data Exchange (ETDEWEB)

Dall' Anese, Emiliano; Simonetto, Andrea; Dhople, Sairaj

2016-12-01

This paper focuses on power distribution networks featuring inverter-interfaced distributed energy resources (DERs), and develops feedback controllers that drive the DER output powers to solutions of time-varying AC optimal power flow (OPF) problems. Control synthesis is grounded on primal-dual-type methods for regularized Lagrangian functions, as well as linear approximations of the AC power-flow equations. Convergence and OPF-solution-tracking capabilities are established while acknowledging: i) communication-packet losses, and ii) partial updates of control signals. The latter case is particularly relevant since it enables asynchronous operation of the controllers where DER setpoints are updated at a fast time scale based on local voltage measurements, and information on the network state is utilized if and when available, based on communication constraints. As an application, the paper considers distribution systems with high photovoltaic integration, and demonstrates that the proposed framework provides fast voltage-regulation capabilities, while enabling the near real-time pursuit of solutions of AC OPF problems.

Computing by Temporal Order: Asynchronous Cellular Automata

Directory of Open Access Journals (Sweden)

Michael Vielhaber

2012-08-01

Full Text Available Our concern is the behaviour of the elementary cellular automata with state set 0,1 over the cell set Z/nZ (one-dimensional finite wrap-around case, under all possible update rules (asynchronicity. Over the torus Z/nZ (n<= 11,we will see that the ECA with Wolfram rule 57 maps any v in F_2^n to any w in F_2^n, varying the update rule. We furthermore show that all even (element of the alternating group bijective functions on the set F_2^n = 0,...,2^n-1, can be computed by ECA57, by iterating it a sufficient number of times with varying update rules, at least for n <= 10. We characterize the non-bijective functions computable by asynchronous rules.

Computational Aspects of Asynchronous CA

OpenAIRE

Chandesris, Jérôme; Dennunzio, Alberto; Formenti, Enrico; Manzoni, Luca

2011-01-01

This work studies some aspects of the computational power of fully asynchronous cellular automata (ACA). We deal with some notions of simulation between ACA and Turing Machines. In particular, we characterize the updating sequences specifying which are "universal", i.e., allowing a (specific family of) ACA to simulate any TM on any input. We also consider the computational cost of such simulations.

Scalability of Several Asynchronous Many-Task Models for In Situ Statistical Analysis.

Energy Technology Data Exchange (ETDEWEB)

Pebay, Philippe Pierre [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Bennett, Janine Camille [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Kolla, Hemanth [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Borghesi, Giulio [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2017-05-01

This report is a sequel to [PB16], in which we provided a first progress report on research and development towards a scalable, asynchronous many-task, in situ statistical analysis engine using the Legion runtime system. This earlier work included a prototype implementation of a proposed solution, using a proxy mini-application as a surrogate for a full-scale scientific simulation code. The first scalability studies were conducted with the above on modestly-sized experimental clusters. In contrast, in the current work we have integrated our in situ analysis engines with a full-size scientific application (S3D, using the Legion-SPMD model), and have conducted nu- merical tests on the largest computational platform currently available for DOE science ap- plications. We also provide details regarding the design and development of a light-weight asynchronous collectives library. We describe how this library is utilized within our SPMD- Legion S3D workflow, and compare the data aggregation technique deployed herein to the approach taken within our previous work.

Flow enforcement algorithms for ATM networks

DEFF Research Database (Denmark)

Dittmann, Lars; Jacobsen, Søren B.; Moth, Klaus

1991-01-01

Four measurement algorithms for flow enforcement in asynchronous transfer mode (ATM) networks are presented. The algorithms are the leaky bucket, the rectangular sliding window, the triangular sliding window, and the exponentially weighted moving average. A comparison, based partly on teletraffic...

Effectiveness of an Asynchronous Online Module on University Students' Understanding of the Bohr Model of the Hydrogen Atom

Science.gov (United States)

Farina, William J., Jr.; Bodzin, Alec M.

2018-01-01

Web-based learning is a growing field in education, yet empirical research into the design of high quality Web-based university science instruction is scarce. A one-week asynchronous online module on the Bohr Model of the atom was developed and implemented guided by the knowledge integration framework. The unit design aligned with three identified…

Synchronization of Hierarchical Time-Varying Neural Networks Based on Asynchronous and Intermittent Sampled-Data Control.

Science.gov (United States)

Xiong, Wenjun; Patel, Ragini; Cao, Jinde; Zheng, Wei Xing

In this brief, our purpose is to apply asynchronous and intermittent sampled-data control methods to achieve the synchronization of hierarchical time-varying neural networks. The asynchronous and intermittent sampled-data controllers are proposed for two reasons: 1) the controllers may not transmit the control information simultaneously and 2) the controllers cannot always exist at any time . The synchronization is then discussed for a kind of hierarchical time-varying neural networks based on the asynchronous and intermittent sampled-data controllers. Finally, the simulation results are given to illustrate the usefulness of the developed criteria.In this brief, our purpose is to apply asynchronous and intermittent sampled-data control methods to achieve the synchronization of hierarchical time-varying neural networks. The asynchronous and intermittent sampled-data controllers are proposed for two reasons: 1) the controllers may not transmit the control information simultaneously and 2) the controllers cannot always exist at any time . The synchronization is then discussed for a kind of hierarchical time-varying neural networks based on the asynchronous and intermittent sampled-data controllers. Finally, the simulation results are given to illustrate the usefulness of the developed criteria.

Realization of station for testing asynchronous three-phase motors

Science.gov (United States)

Wróbel, A.; Surma, W.

2016-08-01

Nowadays, you cannot imagine the construction and operation of machines without the use of electric motors [13-15]. The proposed position is designed to allow testing of asynchronous three-phase motors. The position consists of a tested engine and the engine running as a load, both engines combined with a mechanical clutch [2]. The value of the load is recorded by measuring shaft created with Strain Gauge Bridge. This concept will allow to study the basic parameters of the engines, visualization motor parameters both vector and scalar controlled, during varying load drive system. In addition, registration during the variable physical parameters of the working electric motor, controlled by a frequency converter or controlled by a contactor will be possible. Position is designed as a teaching and research position to characterize the engines. It will be also possible selection of inverter parameters.

Increasing Student Engagement Using Asynchronous Learning

Science.gov (United States)

Northey, Gavin; Bucic, Tania; Chylinski, Mathew; Govind, Rahul

2015-01-01

Student engagement is an ongoing concern for educators because of its positive association with deep learning and educational outcomes. This article tests the use of a social networking site (Facebook) as a tool to facilitate asynchronous learning opportunities that complement face-to-face interactions and thereby enable a stronger learning…

Asynchronous Gossip for Averaging and Spectral Ranking

Science.gov (United States)

Borkar, Vivek S.; Makhijani, Rahul; Sundaresan, Rajesh

2014-08-01

We consider two variants of the classical gossip algorithm. The first variant is a version of asynchronous stochastic approximation. We highlight a fundamental difficulty associated with the classical asynchronous gossip scheme, viz., that it may not converge to a desired average, and suggest an alternative scheme based on reinforcement learning that has guaranteed convergence to the desired average. We then discuss a potential application to a wireless network setting with simultaneous link activation constraints. The second variant is a gossip algorithm for distributed computation of the Perron-Frobenius eigenvector of a nonnegative matrix. While the first variant draws upon a reinforcement learning algorithm for an average cost controlled Markov decision problem, the second variant draws upon a reinforcement learning algorithm for risk-sensitive control. We then discuss potential applications of the second variant to ranking schemes, reputation networks, and principal component analysis.

Violation of the equivalence principle for stressed bodies in asynchronous relativity

Energy Technology Data Exchange (ETDEWEB)

Andrade Martins, R. de (Centro de Logica, Epistemologia e Historia da Ciencia, Campinas (Brazil))

1983-12-11

In the recently developed asynchronous formulation of the relativistic theory of extended bodies, the inertial mass of a body does not explicitly depend on its pressure or stress. The detailed analysis of the weight of a box filled with a gas and placed in a weak gravitational field shows that this feature of asynchronous relativity implies a breakdown of the equivalence between inertial and passive gravitational mass for stressed systems.

On the theoretical gap between synchronous and asynchronous MPC protocols

DEFF Research Database (Denmark)

Beerliová-Trubíniová, Zuzana; Hirt, Martin; Nielsen, Jesper Buus

2010-01-01

that in the cryptographic setting (with setup), the sole reason for it is the distribution of inputs: given an oracle for input distribution, cryptographically-secure asynchronous MPC is possible with the very same condition as synchronous MPC, namely t ..., we show that such an input-distribution oracle can be reduced to an oracle that allows each party to synchronously broadcast one single message. This means that when one single round of synchronous broadcast is available, then asynchronous MPC is possible at the same condition as synchronous MPC...

Novel Simplified Model for Asynchronous Machine with Consideration of Frequency Characteristic

Directory of Open Access Journals (Sweden)

Changchun Cai

2014-01-01

Full Text Available The frequency characteristic of electric equipment should be considered in the digital simulation of power systems. The traditional asynchronous machine third-order transient model excludes not only the stator transient but also the frequency characteristics, thus decreasing the application sphere of the model and resulting in a large error under some special conditions. Based on the physical equivalent circuit and Park model for asynchronous machines, this study proposes a novel asynchronous third-order transient machine model with consideration of the frequency characteristic. In the new definitions of variables, the voltages behind the reactance are redefined as the linear equation of flux linkage. In this way, the rotor voltage equation is not associated with the derivative terms of frequency. However, the derivative terms of frequency should not always be ignored in the application of the traditional third-order transient model. Compared with the traditional third-order transient model, the novel simplified third-order transient model with consideration of the frequency characteristic is more accurate without increasing the order and complexity. Simulation results show that the novel third-order transient model for the asynchronous machine is suitable and effective and is more accurate than the widely used traditional simplified third-order transient model under some special conditions with drastic frequency fluctuations.

Asynchronous Multiparty Computation

DEFF Research Database (Denmark)

Damgård, Ivan Bjerre; Geisler, Martin; Krøigaard, Mikkel

2009-01-01

guarantees termination if the adversary allows a preprocessing phase to terminate, in which no information is released. The communication complexity of this protocol is the same as that of a passively secure solution up to a constant factor. It is secure against an adaptive and active adversary corrupting...... less than n/3 players. We also present a software framework for implementation of asynchronous protocols called VIFF (Virtual Ideal Functionality Framework), which allows automatic parallelization of primitive operations such as secure multiplications, without having to resort to complicated...... multithreading. Benchmarking of a VIFF implementation of our protocol confirms that it is applicable to practical non-trivial secure computations....

Asynchronous vs didactic education: it’s too early to throw in the towel on tradition

Science.gov (United States)

2013-01-01

Background Asynchronous, computer based instruction is cost effective, allows self-directed pacing and review, and addresses preferences of millennial learners. Current research suggests there is no significant difference in learning compared to traditional classroom instruction. Data are limited for novice learners in emergency medicine. The objective of this study was to compare asynchronous, computer-based instruction with traditional didactics for senior medical students during a week-long intensive course in acute care. We hypothesized both modalities would be equivalent. Methods This was a prospective observational quasi-experimental study of 4th year medical students who were novice learners with minimal prior exposure to curricular elements. We assessed baseline knowledge with an objective pre-test. The curriculum was delivered in either traditional lecture format (shock, acute abdomen, dyspnea, field trauma) or via asynchronous, computer-based modules (chest pain, EKG interpretation, pain management, trauma). An interactive review covering all topics was followed by a post-test. Knowledge retention was measured after 10 weeks. Pre and post-test items were written by a panel of medical educators and validated with a reference group of learners. Mean scores were analyzed using dependent t-test and attitudes were assessed by a 5-point Likert scale. Results 44 of 48 students completed the protocol. Students initially acquired more knowledge from didactic education as demonstrated by mean gain scores (didactic: 28.39% ± 18.06; asynchronous 9.93% ± 23.22). Mean difference between didactic and asynchronous = 18.45% with 95% CI [10.40 to 26.50]; p = 0.0001. Retention testing demonstrated similar knowledge attrition: mean gain scores −14.94% (didactic); -17.61% (asynchronous), which was not significantly different: 2.68% ± 20.85, 95% CI [−3.66 to 9.02], p = 0.399. The attitudinal survey revealed that 60.4% of students believed the asynchronous

An Evaluation of Parallel Synchronous and Conservative Asynchronous Logic-Level Simulations

Directory of Open Access Journals (Sweden)

Ausif Mahmood

1996-01-01

a circuit remain fixed during the entire simulation. We remove this limitation and, by extending the analyses to multi-input, multi-output circuits with an arbitrary number of input events, show that the conservative asynchronous simulation extracts more parallelism and executes faster than synchronous simulation in general. Our conclusions are supported by a comparison of the idealized execution times of synchronous and conservative asynchronous algorithms on ISCAS combinational and sequential benchmark circuits.

Psychophysiological effects of synchronous versus asynchronous music during cycling.

Science.gov (United States)

Lim, Harry B T; Karageorghis, Costas I; Romer, Lee M; Bishop, Daniel T

2014-02-01

Synchronizing movement to a musical beat may reduce the metabolic cost of exercise, but findings to date have been equivocal. Our aim was to examine the degree to which the synchronous application of music moderates the metabolic demands of a cycle ergometer task. Twenty-three recreationally active men made two laboratory visits. During the first visit, participants completed a maximal incremental ramp test on a cycle ergometer. At the second visit, they completed four randomized 6-min cycling bouts at 90% of ventilatory threshold (control, metronome, synchronous music, and asynchronous music). Main outcome variables were oxygen uptake, HR, ratings of dyspnea and limb discomfort, affective valence, and arousal. No significant differences were evident for oxygen uptake. HR was lower under the metronome condition (122 ± 15 bpm) compared to asynchronous music (124 ± 17 bpm) and control (125 ± 16 bpm). Limb discomfort was lower while listening to the metronome (2.5 ± 1.2) and synchronous music (2.3 ± 1.1) compared to control (3.0 ± 1.5). Both music conditions, synchronous (1.9 ± 1.2) and asynchronous (2.1 ± 1.3), elicited more positive affective valence compared to metronome (1.2 ± 1.4) and control (1.2 ± 1.2), while arousal was higher with synchronous music (3.4 ± 0.9) compared to metronome (2.8 ± 1.0) and control (2.8 ± 0.9). Synchronizing movement to a rhythmic stimulus does not reduce metabolic cost but may lower limb discomfort. Moreover, synchronous music has a stronger effect on limb discomfort and arousal when compared to asynchronous music.

Emphasis on the Impact of Asynchronous Media

African Journals Online (AJOL)

ICTs and their utilization is one of the most pertinent issues in the education industry today. ... The paper pointed out specific impact of asynchronous ICT media in ... The paper finally noted that the struggle to be part of the digital world is ...

Heating calculation features at self-start of large asynchronous motor

Science.gov (United States)

Shevchenko, A. A.; Temlyakova, Z. S.; Grechkin, V. V.; Vilberger, M. E.

2017-10-01

The article proposes a method for optimizing the incremental heating calculation in the active volume of a large asynchronous motor for certain kinds of load characteristics. The incremental heating calculation is conditioned by the need to determine the aging level of the insulation and to predict a decrease in the electric machine service life. The method for optimizing the incremental heating calculation of asynchronous motor active volume is based on the automation of calculating the heating when simulating the self-starting process of the motor after eliminating an AC drop.

UNIVERSAL REGULAR AUTONOMOUS ASYNCHRONOUS SYSTEMS: ω-LIMIT SETS, INVARIANCE AND BASINS OF ATTRACTION

Directory of Open Access Journals (Sweden)

Serban Vlad

2011-07-01

Full Text Available The asynchronous systems are the non-deterministic real timebinarymodels of the asynchronous circuits from electrical engineering.Autonomy means that the circuits and their models have no input.Regularity means analogies with the dynamical systems, thus such systems may be considered to be real time dynamical systems with a’vector field’, Universality refers to the case when the state space of the system is the greatest possible in the sense of theinclusion. The purpose of this paper is that of defining, by analogy with the dynamical systems theory, the omega-limit sets, the invariance and the basins of attraction of the universal regular autonomous asynchronous systems.

A novel asynchronous access method with binary interfaces

Directory of Open Access Journals (Sweden)

Torres-Solis Jorge

2008-10-01

Full Text Available Abstract Background Traditionally synchronous access strategies require users to comply with one or more time constraints in order to communicate intent with a binary human-machine interface (e.g., mechanical, gestural or neural switches. Asynchronous access methods are preferable, but have not been used with binary interfaces in the control of devices that require more than two commands to be successfully operated. Methods We present the mathematical development and evaluation of a novel asynchronous access method that may be used to translate sporadic activations of binary interfaces into distinct outcomes for the control of devices requiring an arbitrary number of commands to be controlled. With this method, users are required to activate their interfaces only when the device under control behaves erroneously. Then, a recursive algorithm, incorporating contextual assumptions relevant to all possible outcomes, is used to obtain an informed estimate of user intention. We evaluate this method by simulating a control task requiring a series of target commands to be tracked by a model user. Results When compared to a random selection, the proposed asynchronous access method offers a significant reduction in the number of interface activations required from the user. Conclusion This novel access method offers a variety of advantages over traditionally synchronous access strategies and may be adapted to a wide variety of contexts, with primary relevance to applications involving direct object manipulation.

NUMERICAL WITHOUT ITERATION METHOD OF MODELING OF ELECTROMECHANICAL PROCESSES IN ASYNCHRONOUS ENGINES

Directory of Open Access Journals (Sweden)

D. G. Patalakh

2018-02-01

Full Text Available Purpose. Development of calculation of electromagnetic and electromechanic transients is in asynchronous engines without iterations. Methodology. Numeral methods of integration of usual differential equations, programming. Findings. As the system of equations, describing the dynamics of asynchronous engine, contents the products of rotor and stator currents and product of rotation frequency of rotor and currents, so this system is nonlinear one. The numeral solution of nonlinear differential equations supposes an iteration process on every step of integration. Time-continuing and badly converging iteration process may be the reason of calculation slowing. The improvement of numeral method by the way of an iteration process removing is offered. As result the modeling time is reduced. The improved numeral method is applied for integration of differential equations, describing the dynamics of asynchronous engine. Originality. The improvement of numeral method allowing to execute numeral integrations of differential equations containing product of functions is offered, that allows to avoid an iteration process on every step of integration and shorten modeling time. Practical value. On the basis of the offered methodology the universal program of modeling of electromechanics processes in asynchronous engines could be developed as taking advantage on fast-acting.

Dynamic Performances of Asynchronous Machines | Ubeku ...

African Journals Online (AJOL)

The per-phase parameters of a 1.5 hp, 380 V, 50 Hz, 4 poles, 3 phase asynchronous machine used in the simulation were computed with reading obtained from a dc, no-load and blocked rotor tests carried out on the machine in the laboratory. The results obtained from the computer simulations confirmed the capabilities ...

THE ROLE OF OFFLINE METALANGUAGE TALK IN ASYNCHRONOUS COMPUTER-MEDIATED COMMUNICATION

Directory of Open Access Journals (Sweden)

Keiko Kitade

2008-02-01

Full Text Available In order to demonstrate how learners utilize the text-based asynchronous attributes of the Bulletin Board System, this study explored Japanese-as-a-second-language learners' metalanguage episodes (Swain & Lapkin, 1995, 1998 in offline verbal peer speech and online asynchronous discussions with their Japanese key pals. The findings suggest the crucial role of offline collaborative dialogue, the interactional modes in which the episodes occur, and the unique discourse structure of metalanguage episodes concerning online and offline interactions. A high score on the posttest also suggests the high retention of linguistic knowledge constructed through offline peer dialogue. In the offline mode, the learners were able to collaboratively construct knowledge with peers in the stipulated time, while simultaneously focusing on task content in the online interaction. The retrospective interviews and questionnaires reveal the factors that could affect the benefits of the asynchronous computer-mediated communication medium for language learning.

Event-Triggered Asynchronous Guaranteed Cost Control for Markov Jump Discrete-Time Neural Networks With Distributed Delay and Channel Fading.

Science.gov (United States)

Yan, Huaicheng; Zhang, Hao; Yang, Fuwen; Zhan, Xisheng; Peng, Chen

2017-08-18

This paper is concerned with the guaranteed cost control problem for a class of Markov jump discrete-time neural networks (NNs) with event-triggered mechanism, asynchronous jumping, and fading channels. The Markov jump NNs are introduced to be close to reality, where the modes of the NNs and guaranteed cost controller are determined by two mutually independent Markov chains. The asynchronous phenomenon is considered, which increases the difficulty of designing required mode-dependent controller. The event-triggered mechanism is designed by comparing the relative measurement error with the last triggered state at the process of data transmission, which is used to eliminate dispensable transmission and reduce the networked energy consumption. In addition, the signal fading is considered for the effect of signal reflection and shadow in wireless networks, which is modeled by the novel Rice fading models. Some novel sufficient conditions are obtained to guarantee that the closed-loop system reaches a specified cost value under the designed jumping state feedback control law in terms of linear matrix inequalities. Finally, some simulation results are provided to illustrate the effectiveness of the proposed method.

A coupled three dimensional model of vanadium redox flow battery for flow field designs

International Nuclear Information System (INIS)

Yin, Cong; Gao, Yan; Guo, Shaoyun; Tang, Hao

2014-01-01

A 3D (three-dimensional) model of VRB (vanadium redox flow battery) with interdigitated flow channel design is proposed. Two different stack inlet designs, single-inlet and multi-inlet, are structured in the model to study the distributions of fluid pressure, electric potential, current density and overpotential during operation of VRB cell. Electrolyte flow rate and stack channel dimension are proved to be the critical factors affecting flow distribution and cell performance. The model developed in this paper can be employed to optimize both VRB stack design and system operation conditions. Further improvements of the model concerning current density and electrode properties are also suggested in the paper. - Highlights: • A coupled three-dimensional model of vanadium redox flow cell is proposed. • Interdigitated flow channels with two different manifold designs are simulated. • Manifold structure affects uniformity of distribution patterns significantly. • Increased electrolyte flow rate improves cell performance for both designs. • Decreased channel size and enlarged land width enhance cell voltage

Uncertainty Quantification of the Reverse Taylor Impact Test and Localized Asynchronous Space-Time Algorithm

Science.gov (United States)

Subber, Waad; Salvadori, Alberto; Lee, Sangmin; Matous, Karel

2017-06-01

The reverse Taylor impact is a common experiment to investigate the dynamical response of materials at high strain rates. To better understand the physical phenomena and to provide a platform for code validation and Uncertainty Quantification (UQ), a co-designed simulation and experimental paradigm is investigated. For validation under uncertainty, quantities of interest (QOIs) within subregions of the computational domain are introduced. For such simulations where regions of interest can be identified, the computational cost for UQ can be reduced by confining the random variability within these regions of interest. This observation inspired us to develop an asynchronous space and time computational algorithm with localized UQ. In the region of interest, the high resolution space and time discretization schemes are used for a stochastic model. Apart from the region of interest, low spatial and temporal resolutions are allowed for a stochastic model with low dimensional representation of uncertainty. The model is exercised on the linear elastodynamics and shows a potential in reducing the UQ computational cost. Although, we consider wave prorogation in solid, the proposed framework is general and can be used for fluid flow problems as well. Department of Energy, National Nuclear Security Administration (PSAAP-II).

Formal Specification and Verification of Fully Asynchronous Implementations of the Data Encryption Standard

Directory of Open Access Journals (Sweden)

Wendelin Serwe

2015-11-01

Full Text Available This paper presents two formal models of the Data Encryption Standard (DES, a first using the international standard LOTOS, and a second using the more recent process calculus LNT. Both models encode the DES in the style of asynchronous circuits, i.e., the data-flow blocks of the DES algorithm are represented by processes communicating via rendezvous. To ensure correctness of the models, several techniques have been applied, including model checking, equivalence checking, and comparing the results produced by a prototype automatically generated from the formal model with those of existing implementations of the DES. The complete code of the models is provided as appendices and also available on the website of the CADP verification toolbox.

Decentralized automatic generation control of interconnected power systems incorporating asynchronous tie-lines.

Science.gov (United States)

Ibraheem; Hasan, Naimul; Hussein, Arkan Ahmed

2014-01-01

This Paper presents the design of decentralized automatic generation controller for an interconnected power system using PID, Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). The designed controllers are tested on identical two-area interconnected power systems consisting of thermal power plants. The area interconnections between two areas are considered as (i) AC tie-line only (ii) Asynchronous tie-line. The dynamic response analysis is carried out for 1% load perturbation. The performance of the intelligent controllers based on GA and PSO has been compared with the conventional PID controller. The investigations of the system dynamic responses reveal that PSO has the better dynamic response result as compared with PID and GA controller for both type of area interconnection.

Asynchronous interaction, online technologies self-efficacy and self-regulated learning as predictors of academic achievement in an online class

Science.gov (United States)

McGhee, Rosie M. Hector

This research is a correlational study of the relationship among the independent variables: asynchronous interaction, online technologies self-efficacy, and self-regulated learning, and the dependent variable; academic achievement. This study involves an online computer literacy course at a local community college. Very little research exists on the relationship among asynchronous interaction, online technologies self-efficacy and self-regulated learning on predicting academic achievement in an online class. Liu (2008), in his study on student interaction in online courses, concluded that student interaction is a complex issue that needs more research to increase our understanding as it relates to distance education. The purpose of this study was to examine the relationships between asynchronous interaction, online technologies self-efficacy, self-regulated learning and academic achievement in an online computer literacy class at a community college. The researcher used quantitative methods to obtain and analyze data on the relationships among the variables during the summer 2010 semester. Forty-five community college students completed three web-based self-reporting instruments: (a) the GVU 10th WWW User Survey Questionnaire, (b) the Online Technologies Self-Efficacy Survey, and (c) selected items from the Motivated Strategies for Learning Questionnaire. Additional data was obtained from asynchronous discussions posted on Blackboard(TM) Learning Management System. The results of this study found that there were statistically significant relationships between asynchronous interaction and academic achievement (r = .55, p online technologies self-efficacy and academic achievement (r = .50, p online instructors, online course designers, faculty, students and others who are concerned about predictors for online students' success. Also, it serves as a foundation for future research and provides valuable information for educators interested in taking online teaching and

Regression analysis of sparse asynchronous longitudinal data.

Science.gov (United States)

Cao, Hongyuan; Zeng, Donglin; Fine, Jason P

2015-09-01

We consider estimation of regression models for sparse asynchronous longitudinal observations, where time-dependent responses and covariates are observed intermittently within subjects. Unlike with synchronous data, where the response and covariates are observed at the same time point, with asynchronous data, the observation times are mismatched. Simple kernel-weighted estimating equations are proposed for generalized linear models with either time invariant or time-dependent coefficients under smoothness assumptions for the covariate processes which are similar to those for synchronous data. For models with either time invariant or time-dependent coefficients, the estimators are consistent and asymptotically normal but converge at slower rates than those achieved with synchronous data. Simulation studies evidence that the methods perform well with realistic sample sizes and may be superior to a naive application of methods for synchronous data based on an ad hoc last value carried forward approach. The practical utility of the methods is illustrated on data from a study on human immunodeficiency virus.

Asynchronous versus Synchronous Learning in Pharmacy Education

Science.gov (United States)

Motycka, Carol A.; St. Onge, Erin L.; Williams, Jennifer

2013-01-01

Objective: To better understand the technology being used today in pharmacy education through a review of the current methodologies being employed at various institutions. Also, to discuss the benefits and difficulties of asynchronous and synchronous methodologies, which are being utilized at both traditional and distance education campuses.…

Asynchronous Free-Space Optical CDMA Communications System for Last-mile Access Network

DEFF Research Database (Denmark)

Jurado-Navas, Antonio; Raddo, Thiago R.; Sanches, Anderson L.

2016-01-01

We propose a new hybrid asynchronous OCDMA-FSO communications system for access network solutions. New ABER expressions are derived under gamma-gamma scintillation channels, where all users can surprisingly achieve error-free transmissions when FEC is employed.......We propose a new hybrid asynchronous OCDMA-FSO communications system for access network solutions. New ABER expressions are derived under gamma-gamma scintillation channels, where all users can surprisingly achieve error-free transmissions when FEC is employed....

Strict optical orthogonal codes for purely asynchronous code-division multiple-access applications

Science.gov (United States)

Zhang, Jian-Guo

1996-12-01

Strict optical orthogonal codes are presented for purely asynchronous optical code-division multiple-access (CDMA) applications. The proposed code can strictly guarantee the peaks of its cross-correlation functions and the sidelobes of any of its autocorrelation functions to have a value of 1 in purely asynchronous data communications. The basic theory of the proposed codes is given. An experiment on optical CDMA systems is also demonstrated to verify the characteristics of the proposed code.

Realistic modelling of the effects of asynchronous motion at the base of bridge piers

International Nuclear Information System (INIS)

Romanelli, F.; Panza, G.F.; Vaccari, F.

2002-11-01

Frequently long-span bridges provide deep valley crossings, which require special consideration due to the possibility of local amplification of the ground motion as a consequence of topographical irregularities and local soil conditions. This does in fact cause locally enhanced seismic input with the possibility for the bridge piers to respond asynchronously. This introduces special design requirements so that possible out-of-phase ground displacements and the associated large relative displacements of adjacent piers can be accommodated without excessive damage. Assessment of the local variability of the ground motion due to local lateral heterogeneities and to attenuation properties is thus crucial toward the realistic definition of the asynchronous motion at the base of the bridge piers. We illustrate the work done in the framework of a large international cooperation to assess the importance of non-synchronous seismic excitation of long structures. To accomplish this task we compute complete synthetic accelerograms using as input a set of parameters that describes, to the best of our knowledge, the geological structure and seismotectonic setting of the investigated area. (author)

Design of Low Power Multiplier with Energy Efficient Full Adder Using DPTAAL

Directory of Open Access Journals (Sweden)

A. Kishore Kumar

2013-01-01

Full Text Available Asynchronous adiabatic logic (AAL is a novel lowpower design technique which combines the energy saving benefits of asynchronous systems with adiabatic benefits. In this paper, energy efficient full adder using double pass transistor with asynchronous adiabatic logic (DPTAAL is used to design a low power multiplier. Asynchronous adiabatic circuits are very low power circuits to preserve energy for reuse, which reduces the amount of energy drawn directly from the power supply. In this work, an 8×8 multiplier using DPTAAL is designed and simulated, which exhibits low power and reliable logical operations. To improve the circuit performance at reduced voltage level, double pass transistor logic (DPL is introduced. The power results of the proposed multiplier design are compared with the conventional CMOS implementation. Simulation results show significant improvement in power for clock rates ranging from 100 MHz to 300 MHz.

Constraints on the design of flow measuring structures over a large dynamic flow range

International Nuclear Information System (INIS)

Hickey, M.J.; Holmes, R.M.

1979-01-01

Topographical restraints for design storm flow are described as sharp-crested weirs for low flows in series with broad-crested weirs for the high flows. These design selections are considered to be most economical while providing the specified flow measuring capabilities for movement of radionuclides from the solid waste disposal areas into the surface streams around ORNL

ON THE ISSUE OF VECTOR CONTROL OF THE ASYNCHRONOUS MOTORS

Directory of Open Access Journals (Sweden)

B. I. Firago

2015-01-01

Full Text Available The paper considers the issue of one of the widespread types of vector control realization for the asynchronous motors with a short-circuited rotor. Of all more than 20 vector control types known presently, the following are applied most frequently: direct vector control with velocity pickup (VP, direct vector control without VP, indirect vector control with VP and indirect vector control without VP. Despite the fact that the asynchronous-motor indirect vector control without VP is the easiest and most spread, the absence of VP does not allow controlling the motor electromagnetic torque at zero velocity. This is the reason why for electric motor drives of such requirements they utilize the vector control with a velocity transducer. The systems of widest dissemination became the direct and indirect vector control systems with X-axis alignment of the synchronously rotating x–y-coordinate frame along the rotor flux-linkage vector inasmuch as this provides the simplest correlations for controlling variables. Although these two types of vector control are well presented in literature, a number of issues concerning their realization and practical application require further elaboration. These include: the block schemes adequate representation as consisted with the modern realization of vector control and clarification of the analytical expressions for evaluating the regulator parameters.The authors present a technique for evaluating the dynamics of an asynchronous electric motor drive with direct vector control and x-axis alignment along the vector of rotor flux linkage. The article offers a generalized structure of this vector control type with detailed description of its principal blocks: controlling system, frequency converter, and the asynchronous motor.The paper presents a direct vector control simulating model developed in the MatLab environment on the grounds of this structure. The authors illustrate the described technique with the results

An Autonomous Wireless Sensor Node With Asynchronous ECG Monitoring in 0.18 μ m CMOS.

Science.gov (United States)

Mansano, Andre L; Li, Yongjia; Bagga, Sumit; Serdijn, Wouter A

2016-06-01

The design of a 13.56 MHz/402 MHz autonomous wireless sensor node with asynchronous ECG monitoring for near field communication is presented. The sensor node consists of an RF energy harvester (RFEH), a power management unit, an ECG readout, a data encoder and an RF backscattering transmitter. The energy harvester supplies the system with 1.25 V and offers a power conversion efficiency of 19% from a -13 dBm RF source at 13.56 MHz. The power management unit regulates the output voltage of the RFEH to supply the ECG readout with VECG = 0.95 V and the data encoder with VDE = 0.65 V . The ECG readout comprises an analog front-end (low noise amplifier and programmable voltage to current converter) and an asynchronous level crossing ADC with 8 bits resolution. The ADC output is encoded by a pulse generator that drives a backscattering transmitter at 402 MHz. The total power consumption of the sensor node circuitry is 9.7 μ W for a data rate of 90 kb/s and a heart rate of 70 bpm. The chip has been designed in a 0.18 μm CMOS process and shows superior RF input power sensitivity and lower power consumption when compared to previous works.

Towards Separation of Concerns in Flow-Based Programming

DEFF Research Database (Denmark)

Zarrin, Bahram; Baumeister, Hubert

2015-01-01

Flow-Based Programming (FBP) is a programming paradigm that models software systems as a directed graph of predefined processes which run asynchronously and exchange data through input and output ports. FBP decomposes software systems into a network of processes. However there are concerns...

Laser dynamics of asynchronous rational harmonic mode-locked fiber soliton lasers

International Nuclear Information System (INIS)

Jyu, Siao-Shan; Jiang, Guo-Hao; Lai, Yinchieh

2013-01-01

Laser dynamics of asynchronous rational harmonic mode-locked (ARHM) fiber soliton lasers are investigated in detail. In particular, based on the unique laser dynamics of asynchronous mode-locking, we have developed a new method for determining the effective active modulation strength in situ for ARHM lasers. By measuring the magnitudes of the slowly oscillating pulse timing position and central frequency, the effective phase modulation strength at the multiplication frequency of rational harmonic mode-locking can be accurately inferred. The method can be a very useful tool for developing ARHM fiber lasers. (paper)

Adaptive hatching hypotheses do not explain asynchronous ...

African Journals Online (AJOL)

At the core of the suite of adaptive hatching hypotheses advanced to explain asynchronous hatching in birds is the assumption that if food is not limited then all the hatchlings will develop normally to adulthood. In this study Brown-headed Parrot Poicephalus cryptoxanthus chicks were hand fed and weighed on a daily basis.

Managing Asynchronous Data in ATLAS's Concurrent Framework

CERN Document Server

Baines, John; The ATLAS collaboration

2016-01-01

In order to be able to make effective use of emerging hardware, where the amount of memory available to any CPU is rapidly decreasing as the core count continues to rise, ATLAS has begun a migration to a concurrent, multi-threaded software framework, known as AthenaMT. Significant progress has been made in implementing AthenaMT - we can currently run realistic Geant4 simulations on massively concurrent machines. the migration of realistic prototypes of reconstruction workflows is more difficult, given the large amounts of legacy code and the complexity and challenges of reconstruction software. These types of workflows, however, are the types that will most benefit from the memory reduction features of a multi-threaded framework. One of the challenges that we will report on in this paper is the re-design and implementation of several key asynchronous technologies whose behaviour is radically different in a concurrent environment than in a serial one, namely the management of Conditions data and the Detector D...

Efficiency of three-phase asynchronous motors. Energy loss reduction by means of overdimensioning; Efficientie van driefasen asynchrone motoren. SinuMEC beperkt energieverlies door overdimensionering

Energy Technology Data Exchange (ETDEWEB)

Peeters, J.; Van Dorst, C. [Hyteps, Gemert (Netherlands)

2008-10-15

The three phase asynchronous motor has been applied in various installations since time immemorial. Although the motor is more efficient at full mechanical load, this is not always applied efficiently. Can the efficiency of low load motors be improved or is this a utopia? The Sinusoidal Motor Controller (SinuMEC) improves efficiency, saves energy and lengthens the life span. [mk]. [Dutch] De driefasen asynchrone motor wordt sinds mensenheugenis in uiteenlopende installaties toegepast. Hoewel de motor met een volle mechanische belasting efficient is, wordt deze niet altijd efficient toegepast. Kan de efficiency van laag belaste motoren worden verbeterd of is dit een utopie? De Sinusoidal Motor efficiency controller (SinuMEC) verbetert de efficiency, bespaart energie en verlengt de levensduur.

Determining sociability, social space, and social presence in (a)synchronous collaborative groups.

Science.gov (United States)

Kreijns, Karel; Kirschner, Paul A; Jochems, Wim; Van Buuren, Hans

2004-04-01

The effectiveness of group learning in asynchronous distributed learning groups depends on the social interaction that takes place. This social interaction affects both cognitive and socioemotional processes that take place during learning, group forming, establishment of group structures, and group dynamics. Though now known to be important, this aspect is often ignored, denied or forgotten by educators and researchers who tend to concentrate on cognitive processes and on-task contexts. This "one-sided" educational focus largely determines the set of requirements in the design of computer-supported collaborative learning (CSCL) environments resulting in functional CSCL environments. In contrast, our research is aimed at the design and implementation of sociable CSCL environments which may increase the likelihood that a sound social space will emerge. We use a theoretical framework that is based upon an ecological approach to social interaction, centering on the concept of social affordances, the concept of the sociability of CSCL environments, and social presence theory. The hypothesis is that the higher the sociability, the more likely that social interaction will take place or will increase, and the more likely that this will result in an emerging sound social space. In the present research, the variables of interest are sociability, social space, and social presence. This study deals with the construction and validation of three instruments to determine sociability, social space, and social presence in (a)synchronous collaborating groups. The findings suggest that the instruments have potential to be useful as measures for the respective variables. However, it must be realized that these measures are "first steps."

Analysis and application of two recursive parametric estimation algorithms for an asynchronous machine

International Nuclear Information System (INIS)

Damek, Nawel; Kamoun, Samira

2011-01-01

In this communication, two recursive parametric estimation algorithms are analyzed and applied to an squirrelcage asynchronous machine located at the research ''Unit of Automatic Control'' (UCA) at ENIS. The first algorithm which, use the transfer matrix mathematical model, is based on the gradient principle. The second algorithm, which use the state-space mathematical model, is based on the minimization of the estimation error. These algorithms are applied as a key technique to estimate asynchronous machine with unknown, but constant or timevarying parameters. Stator voltage and current are used as measured data. The proposed recursive parametric estimation algorithms are validated on the experimental data of an asynchronous machine under normal operating condition as full load. The results show that these algorithms can estimate effectively the machine parameters with reliability.

An Efficient Algorithm for Computing Attractors of Synchronous And Asynchronous Boolean Networks

Science.gov (United States)

Zheng, Desheng; Yang, Guowu; Li, Xiaoyu; Wang, Zhicai; Liu, Feng; He, Lei

2013-01-01

Biological networks, such as genetic regulatory networks, often contain positive and negative feedback loops that settle down to dynamically stable patterns. Identifying these patterns, the so-called attractors, can provide important insights for biologists to understand the molecular mechanisms underlying many coordinated cellular processes such as cellular division, differentiation, and homeostasis. Both synchronous and asynchronous Boolean networks have been used to simulate genetic regulatory networks and identify their attractors. The common methods of computing attractors are that start with a randomly selected initial state and finish with exhaustive search of the state space of a network. However, the time complexity of these methods grows exponentially with respect to the number and length of attractors. Here, we build two algorithms to achieve the computation of attractors in synchronous and asynchronous Boolean networks. For the synchronous scenario, combing with iterative methods and reduced order binary decision diagrams (ROBDD), we propose an improved algorithm to compute attractors. For another algorithm, the attractors of synchronous Boolean networks are utilized in asynchronous Boolean translation functions to derive attractors of asynchronous scenario. The proposed algorithms are implemented in a procedure called geneFAtt. Compared to existing tools such as genYsis, geneFAtt is significantly faster in computing attractors for empirical experimental systems. Availability The software package is available at https://sites.google.com/site/desheng619/download. PMID:23585840

Asynchronous Channel-Hopping Scheme under Jamming Attacks

Directory of Open Access Journals (Sweden)

Yongchul Kim

2018-01-01

Full Text Available Cognitive radio networks (CRNs are considered an attractive technology to mitigate inefficiency in the usage of licensed spectrum. CRNs allow the secondary users (SUs to access the unused licensed spectrum and use a blind rendezvous process to establish communication links between SUs. In particular, quorum-based channel-hopping (CH schemes have been studied recently to provide guaranteed blind rendezvous in decentralized CRNs without using global time synchronization. However, these schemes remain vulnerable to jamming attacks. In this paper, we first analyze the limitations of quorum-based rendezvous schemes called asynchronous channel hopping (ACH. Then, we introduce a novel sequence sensing jamming attack (SSJA model in which a sophisticated jammer can dramatically reduce the rendezvous success rates of ACH schemes. In addition, we propose a fast and robust asynchronous rendezvous scheme (FRARS that can significantly enhance robustness under jamming attacks. Our numerical results demonstrate that the performance of the proposed scheme vastly outperforms the ACH scheme when there are security concerns about a sequence sensing jammer.

An asynchronous rapid single-flux-quantum demultiplexer based on dual-rail information coding

International Nuclear Information System (INIS)

Dimov, B; Khabipov, M; Balashov, D; Brandt, C M; Buchholz, F-Im; Niemeyer, J; Uhlmann, F H

2005-01-01

We present a novel asynchronous RSFQ demultiplexer based on dual-rail information coding. The electrical scheme of the circuit is designed and optimized to maximize the margins of its elements and to improve the fabrication yield. This optimized scheme has been fabricated with the 4 μm 1 kA cm -2 Nb/Al 2 O 3 -Al/Nb technology of PTB-Braunschweig. The demultiplexer has been tested with different samples of the low-speed incoming data stream and in all cases a correct circuit functionality has been observed

Positive semidefinite integrated covariance estimation, factorizations and asynchronicity

DEFF Research Database (Denmark)

Boudt, Kris; Laurent, Sébastien; Lunde, Asger

2017-01-01

An estimator of the ex-post covariation of log-prices under asynchronicity and microstructure noise is proposed. It uses the Cholesky factorization of the covariance matrix in order to exploit the heterogeneity in trading intensities to estimate the different parameters sequentially with as many...

Positive Semidefinite Integrated Covariance Estimation, Factorizations and Asynchronicity

DEFF Research Database (Denmark)

Boudt, Kris; Laurent, Sébastien; Lunde, Asger

An estimator of the ex-post covariation of log-prices under asynchronicity and microstructure noise is proposed. It uses the Cholesky factorization on the correlation matrix in order to exploit the heterogeneity in trading intensity to estimate the different parameters sequentially with as many...

Position paper -- Tank ventilation system design air flow rates

International Nuclear Information System (INIS)

Goolsby, G.K.

1995-01-01

The purpose of this paper is to document a project position on required ventilation system design air flow rates for the waste storage tanks currently being designed by project W-236A, the Multi-Function Waste Tank Facility (MWTF). The Title 1 design primary tank heat removal system consists of two systems: a primary tank vapor space ventilation system; and an annulus ventilation system. At the conclusion of Title 1 design, air flow rates for the primary and annulus ventilation systems were 960 scfm and 4,400 scfm, respectively, per tank. These design flow rates were capable of removing 1,250,000 Btu/hr from each tank. However, recently completed and ongoing studies have resulted in a design change to reduce the extreme case heat load to 700,000 Btu/hr. This revision of the extreme case heat load, coupled with results of scale model evaporative testing performed by WHC Thermal Hydraulics, allow for a reduction of the design air flow rates for both primary and annulus ventilation systems. Based on the preceding discussion, ICF Kaiser Hanford Co. concludes that the design should incorporate the following design air flow rates: Primary ventilation system--500 scfm maximum and Annulus ventilation system--1,100 scfm maximum. In addition, the minimum air flow rates in the primary and annulus ventilation systems will be investigated during Title 2 design. The results of the Title 2 investigation will determine the range of available temperature control using variable air flows to both ventilation systems

Verification and Planning for Stochastic Processes with Asynchronous Events

National Research Council Canada - National Science Library

Younes, Hakan L

2005-01-01

.... The most common assumption is that of history-independence: the Markov assumption. In this thesis, the author considers the problems of verification and planning for stochastic processes with asynchronous events, without relying on the Markov assumption...

Information Flows in Networked Engineering Design Projects

DEFF Research Database (Denmark)

Parraguez, Pedro; Maier, Anja

Complex engineering design projects need to manage simultaneously multiple information flows across design activities associated with different areas of the design process. Previous research on this area has mostly focused on either analysing the “required information flows” through activity...... networks at the project level or in studying the social networks that deliver the “actual information flow”. In this paper we propose and empirically test a model and method that integrates both social and activity networks into one compact representation, allowing to compare actual and required...... information flows between design spaces, and to assess the influence that these misalignments could have on the performance of engineering design projects....

Evaluation of asynchronous E-learning in the geography curriculum: enriching learning quality in Saudi high schools

OpenAIRE

Al Dobaikhi, Hend; Woollard, John

2011-01-01

The impacts of emerging ICT into educational curricula Asynchronous discussion forumDiscussion groups via e-learning environmentPosting questions and commentsSelf-efficacy in asynchronous e-learning Web community participationCollaborative learning can be fosteredPositive impacts on objectives of educational curriculum

Operational aspects of asynchronous filtering for improved flood forecasting

Science.gov (United States)

Rakovec, Oldrich; Weerts, Albrecht; Sumihar, Julius; Uijlenhoet, Remko

2014-05-01

and assimilation and is suitable to be connected to any kind of environmental model. This setup is embedded in the Delft Flood Early Warning System (Delft-FEWS, Werner et al., 2013) for making all simulations and forecast runs and handling of all hydrological and meteorological data. References: Evensen, G. (2009), Data Assimilation: The Ensemble Kalman Filter, Springer, doi:10.1007/978-3-642-03711-5. OpenDA (2013), The OpenDA data-assimilation toolbox, www.openda.org, (last access: 1 November 2013). OpenStreams (2013), OpenStreams, www.openstreams.nl, (last access: 1 November 2013). Sakov, P., G. Evensen, and L. Bertino (2010), Asynchronous data assimilation with the EnKF, Tellus, Series A: Dynamic Meteorology and Oceanography, 62(1), 24-29, doi:10.1111/j.1600-0870.2009.00417.x. Werner, M., J. Schellekens, P. Gijsbers, M. van Dijk, O. van den Akker, and K. Heynert (2013), The Delft-FEWS flow forecasting system, Environ. Mod. & Soft., 40(0), 65-77, doi: http://dx.doi.org/10.1016/j.envsoft.2012.07.010.

Operation Characteristics Optimization of Low Power Three-Phase Asynchronous Motors

Directory of Open Access Journals (Sweden)

VLAD, I.

2014-02-01

Full Text Available Most published papers on low power asynchronous motors were aimed to achieve better operational performances in different operating conditions. The optimal design of the general-purpose motors requires searching and selecting an electric machine to meet minimum operating costs criterion and certain customer imposed restrictive conditions. In this paper, there are many significant simulations providing qualitative and quantitative information on reducing active and reactive energy losses in motors, and on parameters and constructive solution. The optimization study applied the minimal operating costs criterion, and it took into account the starting restrictive conditions. Thirteen variables regarding electromagnetic stresses and main constructive dimensions were considered. The operating costs of the optimized motor decreased with 25.6%, as compared to the existing solution. This paper can be a practical and theoretical support for the development and implementation of modern design methods, based on theoretical and experimental study of stationary and transient processes in low power motors, to increase efficiency and power factor.

Adding the Human Touch to Asynchronous Online Learning

Science.gov (United States)

Glenn, Cynthia Wheatley

2018-01-01

For learners to actively accept responsibility in a virtual classroom platform, it is necessary to provide special motivation extending across the traditional classroom setting into asynchronous online learning. This article explores specific ways to do this that bridge the gap between ground and online students' learning experiences, and how…

Asynchronous decision making in a memorized paddle pressing task.

Science.gov (United States)

Dankert, James R; Olson, Byron; Si, Jennie

2008-12-01

This paper presents a method for asynchronous decision making using recorded neural data in a binary decision task. This is a demonstration of a technique for developing motor cortical neural prosthetics that do not rely on external cued timing information. The system presented in this paper uses support vector machines and leaky integrate-and-fire elements to predict directional paddle presses. In addition to the traditional metrics of accuracy, asynchronous systems must also optimize the time needed to make a decision. The system presented is able to predict paddle presses with a median accuracy of 88% and all decisions are made before the time of the actual paddle press. An alternative bit rate measure of performance is defined to show that the system proposed here is able to perform the task with the same efficiency as the rats.

Features of the Asynchronous Correlation between the China Coal Price Index and Coal Mining Accidental Deaths

Science.gov (United States)

Huang, Yuecheng; Cheng, Wuyi; Luo, Sida; Luo, Yun; Ma, Chengchen; He, Tailin

2016-01-01

The features of the asynchronous correlation between accident indices and the factors that influence accidents can provide an effective reference for warnings of coal mining accidents. However, what are the features of this correlation? To answer this question, data from the China coal price index and the number of deaths from coal mining accidents were selected as the sample data. The fluctuation modes of the asynchronous correlation between the two data sets were defined according to the asynchronous correlation coefficients, symbolization, and sliding windows. We then built several directed and weighted network models, within which the fluctuation modes and the transformations between modes were represented by nodes and edges. Then, the features of the asynchronous correlation between these two variables could be studied from a perspective of network topology. We found that the correlation between the price index and the accidental deaths was asynchronous and fluctuating. Certain aspects, such as the key fluctuation modes, the subgroups characteristics, the transmission medium, the periodicity and transmission path length in the network, were analyzed by using complex network theory, analytical methods and spectral analysis method. These results provide a scientific reference for generating warnings for coal mining accidents based on economic indices. PMID:27902748

The study of transient processes in the asynchronous starting of the synchronous motor

OpenAIRE

Alexandru Bârlea; Olivian Chiver

2012-01-01

Starting synchronous motors can be achieved by several ethods: starting with an auxiliary motor launch, starting in asynchronous regim, by feeding from a variable frequency source, auto-synchronization with the network.. In our case we study the transient processes in a asynchronous regim . In this case the synchronous motor is started like a squirrel cage induction motor . To start, the synchronous motor is equipped with a starting winding cage placed in the pole pieces of polar inducers; la...

Asynchronous hatching provides females with a means for increasing male care but incurs a cost by reducing offspring fitness.

Science.gov (United States)

Ford, L E; Smiseth, P T

2016-02-01

In species with biparental care, sexual conflict occurs because the benefit of care depends on the total amount of care provided by the two parents while the cost of care depends on each parent's own contribution. Asynchronous hatching may play a role in mediating the resolution of this conflict over parental care. The sexual conflict hypothesis for the evolution of asynchronous hatching suggests that females adjust hatching patterns in order to increase male parental effort relative to female effort. We tested this hypothesis in the burying beetle Nicrophorus vespilloides by setting up experimental broods with three different hatching patterns: synchronous, asynchronous and highly asynchronous broods. As predicted, we found that males provided care for longer in asynchronous broods whereas the opposite was true of females. However, we did not find any benefit to females of reducing their duration of care in terms of increased lifespan or reduced mass loss during breeding. We found substantial negative effects of hatching asynchrony on offspring fitness as larval mass was lower and fewer larvae survived to dispersal in highly asynchronous broods compared to synchronous or asynchronous broods. Our results suggest that, even though females can increase male parental effort by hatching their broods more asynchronously, females pay a substantial cost from doing so in terms of reducing offspring growth and survival. Thus, females should be under selection to produce a hatching pattern that provides the best possible trade-off between the benefits of increased male parental effort and the costs due to reduced offspring fitness. © 2015 European Society For Evolutionary Biology. Journal of Evolutionary Biology © 2015 European Society For Evolutionary Biology.

Building a Practical Natural Laminar Flow Design Capability

Science.gov (United States)

Campbell, Richard L.; Lynde, Michelle N.

2017-01-01

A preliminary natural laminar flow (NLF) design method that has been developed and applied to supersonic and transonic wings with moderate-to-high leading-edge sweeps at flight Reynolds numbers is further extended and evaluated in this paper. The modular design approach uses a knowledge-based design module linked with different flow solvers and boundary layer stability analysis methods to provide a multifidelity capability for NLF analysis and design. An assessment of the effects of different options for stability analysis is included using pressures and geometry from an NLF wing designed for the Common Research Model (CRM). Several extensions to the design module are described, including multiple new approaches to design for controlling attachment line contamination and transition. Finally, a modification to the NLF design algorithm that allows independent control of Tollmien-Schlichting (TS) and cross flow (CF) modes is proposed. A preliminary evaluation of the TS-only option applied to the design of an NLF nacelle for the CRM is performed that includes the use of a low-fidelity stability analysis directly in the design module.

Asynchronous Assessment in a Large Lecture Marketing Course

Science.gov (United States)

Downey, W. Scott; Schetzsle, Stacey

2012-01-01

Asynchronous assessment, which includes quizzes or exams online or outside class, offers marketing educators an opportunity to make more efficient use of class time and to enhance students' learning experiences by giving them more flexibility and choice in their assessment environment. In this paper, we examine the performance difference between…

Design and validation of a uniform flow microreactor

Energy Technology Data Exchange (ETDEWEB)

Yi, Seung Jae; Kim, Kyung Chun; Chang, Seung Cheol [Pusan National University, Busan (Korea, Republic of); Park, Ji Min [Global HQ, Hankook Tire Co., Daejeon (Korea, Republic of)

2014-01-15

We present a design method to characterize uniform flows in a microreactor for high performance surface plasmon resonance (SPR) a general-purpose biosensor chips. The shape of the microreactor is designed based on an approximate pressure drop model. The number of micro-pillars and the slopes of the inlet and outlet linear chambers are two dominant parameters used to minimize the velocity difference in the microreactor. The flow uniformity was examined quantitatively by numerical and experimental visualization methods. A computational fluid dynamics (CFD) analysis demonstrates that the designed microreactor has a fairly uniform velocity profile in the reaction zone for a wide range of flow rates. The velocity field in the fabricated microreactor was measured using the micro-particle image velocimetry (μ-PIV) method, and the flow uniformity was confirmed experimentally. The performance of the uniform flow microreactor was verified using the fluorescence antibody technique.

Spaceflight Flow Cytometry: Design Challenges and Applications

Science.gov (United States)

Pappas, Dimitri; Kao, Shih-Hsin; Jeevarajan, Antony S.

2004-01-01

Future space exploration missions will require analytical technology capable of providing both autonomous medical care to the crew and investigative capabilities to researchers. While several promising candidate technologies exist for further development, flow cytometry is an attractive technology as it offers both crew health and a wide array of biochemistry and immunology assays. While flow cytometry has been widely used for cellular analysis in both clinical and research settings, the requirements for proper operation in spaceflight impose constraints on any instrument designs. The challenges of designing a spaceflight-ready flow cytometer are discussed, as well as some preliminary results using a prototype system.

Spatiotemporal Features for Asynchronous Event-based Data

Directory of Open Access Journals (Sweden)

Xavier eLagorce

2015-02-01

Full Text Available Bio-inspired asynchronous event-based vision sensors are currently introducing a paradigm shift in visual information processing. These new sensors rely on a stimulus-driven principle of light acquisition similar to biological retinas. They are event-driven and fully asynchronous, thereby reducing redundancy and encoding exact times of input signal changes, leading to a very precise temporal resolution. Approaches for higher-level computer vision often rely on the realiable detection of features in visual frames, but similar definitions of features for the novel dynamic and event-based visual input representation of silicon retinas have so far been lacking. This article addresses the problem of learning and recognizing features for event-based vision sensors, which capture properties of truly spatiotemporal volumes of sparse visual event information. A novel computational architecture for learning and encoding spatiotemporal features is introduced based on a set of predictive recurrent reservoir networks, competing via winner-take-all selection. Features are learned in an unsupervised manner from real-world input recorded with event-based vision sensors. It is shown that the networks in the architecture learn distinct and task-specific dynamic visual features, and can predict their trajectories over time.

Design, Modelling and Analysis of a Workflow Reconfiguration

DEFF Research Database (Denmark)

Mazzara, Manuel; Abouzaid, Faisal; Dragoni, Nicola

2011-01-01

This paper describes a case study involving the reconfiguration of an office workflow. We state the requirements on a system implementing the workflow and its reconfiguration, and describe the system’s design in BPMN. We then use an asynchronous pi-calculus and Web.1 to model the design and to ve......This paper describes a case study involving the reconfiguration of an office workflow. We state the requirements on a system implementing the workflow and its reconfiguration, and describe the system’s design in BPMN. We then use an asynchronous pi-calculus and Web.1 to model the design...

Asynchronous replication and autosome-pair non-equivalence in human embryonic stem cells.

Directory of Open Access Journals (Sweden)

Devkanya Dutta

Full Text Available A number of mammalian genes exhibit the unusual properties of random monoallelic expression and random asynchronous replication. Such exceptional genes include genes subject to X inactivation and autosomal genes including odorant receptors, immunoglobulins, interleukins, pheromone receptors, and p120 catenin. In differentiated cells, random asynchronous replication of interspersed autosomal genes is coordinated at the whole chromosome level, indicative of chromosome-pair non-equivalence. Here we have investigated the replication pattern of the random asynchronously replicating genes in undifferentiated human embryonic stem cells, using fluorescence in situ hybridization based assay. We show that allele-specific replication of X-linked genes and random monoallelic autosomal genes occur in human embryonic stem cells. The direction of replication is coordinated at the whole chromosome level and can cross the centromere, indicating the existence of autosome-pair non-equivalence in human embryonic stem cells. These results suggest that epigenetic mechanism(s that randomly distinguish between two parental alleles are emerging in the cells of the inner cell mass, the source of human embryonic stem cells.

Student Participation and Interactivity Using Asynchronous Computer-Mediated Communication for Resolution of an Undergraduate Capstone Management Case Study

OpenAIRE

Miller, Paulette J.

2012-01-01

Online discussion activities are designed for computer-mediated learning activities in face-to-face, hybrid, and totally online courses. The use of asynchronous computer-mediated communication (A-CMC) coupled with authentic workplace case studies provides students in the protected learning environment with opportunities to practice workplace decision making and communication. In this study, communication behaviors of transmitter and receiver were analyzed to determine participation and intera...

Content Analysis Coding Schemes for Online Asynchronous Discussion

Science.gov (United States)

Weltzer-Ward, Lisa

2011-01-01

Purpose: Researchers commonly utilize coding-based analysis of classroom asynchronous discussion contributions as part of studies of online learning and instruction. However, this analysis is inconsistent from study to study with over 50 coding schemes and procedures applied in the last eight years. The aim of this article is to provide a basis…

Miscellany of Students' Satisfaction in an Asynchronous Learning Environment

Science.gov (United States)

Larbi-Siaw, Otu; Owusu-Agyeman, Yaw

2017-01-01

This study investigates the determinants of students' satisfaction in an asynchronous learning environment using seven key considerations: the e-learning environment, student-content interaction, student and student interaction, student-teacher interaction, group cohesion and timely participation, knowledge of Internet usage, and satisfaction. The…

Flow Control Enabled Aircraft Design

National Research Council Canada - National Science Library

Nangia, Rajendar

2004-01-01

...: Many future advanced aircraft concepts being considered by the Air Force fall outside the current aerodynamic design practice and will rely heavily on the use of flow control technology to optimize flight performance...

A Novel Approach to Asynchronous MVP Data Interpretation Based on Elliptical-Vectors

Science.gov (United States)

Kruglyakov, M.; Trofimov, I.; Korotaev, S.; Shneyer, V.; Popova, I.; Orekhova, D.; Scshors, Y.; Zhdanov, M. S.

2014-12-01

We suggest a novel approach to asynchronous magnetic-variation profiling (MVP) data interpretation. Standard method in MVP is based on the interpretation of the coefficients of linear relation between vertical and horizontal components of the measured magnetic field.From mathematical point of view this pair of linear coefficients is not a vector which leads to significant difficulties in asynchronous data interpretation. Our approach allows us to actually treat such a pair of complex numbers as a special vector called an ellipse-vector (EV). By choosing the particular definitions of complex length and direction, the basic relation of MVP can be considered as the dot product. This considerably simplifies the interpretation of asynchronous data. The EV is described by four real numbers: the values of major and minor semiaxes, the angular direction of the major semiaxis and the phase. The notation choice is motivated by historical reasons. It is important that different EV's components have different sensitivity with respect to the field sources and the local heterogeneities. Namely, the value of major semiaxis and the angular direction are mostly determined by the field source and the normal cross-section. On the other hand, the value of minor semiaxis and the phase are responsive to local heterogeneities. Since the EV is the general form of complex vector, the traditional Schmucker vectors can be explicitly expressed through its components.The proposed approach was successfully applied to interpretation the results of asynchronous measurements that had been obtained in the Arctic Ocean at the drift stations "North Pole" in 1962-1976.

Fractal flow design how to design bespoke turbulence and why

CERN Document Server

Vassilicos, Christos

2016-01-01

This book focuses on turbulent flows generated and/or influenced by multiscale/fractal structures. It consists of six chapters which demonstrate, each one in its own way, how such structures and objects can be used to design bespoke turbulence for particular applications and also how they can be used for fundamental studies of turbulent flows.

Discrete method for design of flow distribution in manifolds

International Nuclear Information System (INIS)

Wang, Junye; Wang, Hualin

2015-01-01

Flow in manifold systems is encountered in designs of various industrial processes, such as fuel cells, microreactors, microchannels, plate heat exchanger, and radial flow reactors. The uniformity of flow distribution in manifold is a key indicator for performance of the process equipment. In this paper, a discrete method for a U-type arrangement was developed to evaluate the uniformity of the flow distribution and the pressure drop and then was used for direct comparisons between the U-type and the Z-type. The uniformity of the U-type is generally better than that of the Z-type in most of cases for small ζ and large M. The U-type and the Z-type approach each other as ζ increases or M decreases. However, the Z-type is more sensitive to structures than the U-type and approaches uniform flow distribution faster than the U-type as M decreases or ζ increases. This provides a simple yet powerful tool for the designers to evaluate and select a flow arrangement and offers practical measures for industrial applications. - Highlights: • Discrete methodology of flow field designs in manifolds with U-type arrangements. • Quantitative comparison between U-type and Z-type arrangements. • Discrete solution of flow distribution with varying flow coefficients. • Practical measures and guideline to design of manifold systems.

The Interplay of Content and Community in Synchronous and Asynchronous Communication: Virtual Communication in a Graduate Seminar

Directory of Open Access Journals (Sweden)

Richard A. Schwier

2002-06-01

Full Text Available A group of graduate students and an instructor at the University of Saskatchewan experimented with the use of synchronous communication (chat and asynchronous communication (bulletin board in a theory course in Educational Communications and Technology for an eight-month period. Synchronous communication contributed dramatically to the continuity and convenience of the class, and promoted a strong sense of community. At the same time, it was viewed as less effective than asynchronous communication for dealing with content and issues deeply, and it introduced a number of pedagogical and intellectual limitations. We concluded that synchronous and asynchronous strategies were suitable for different types of learning, and what we experienced was a balancing act between content and community in our group. A combination of synchronous and asynchronous experiences seems to be necessary to promote the kind of engagement and depth required in a graduate seminar.

Performance analysis of 2D asynchronous hard-limiting optical code-division multiple access system through atmospheric scattering channel

Science.gov (United States)

Zhao, Yaqin; Zhong, Xin; Wu, Di; Zhang, Ye; Ren, Guanghui; Wu, Zhilu

2013-09-01

Optical code-division multiple access (OCDMA) systems usually allocate orthogonal or quasi-orthogonal codes to the active users. When transmitting through atmospheric scattering channel, the coding pulses are broadened and the orthogonality of the codes is worsened. In truly asynchronous case, namely both the chips and the bits are asynchronous among each active user, the pulse broadening affects the system performance a lot. In this paper, we evaluate the performance of a 2D asynchronous hard-limiting wireless OCDMA system through atmospheric scattering channel. The probability density function of multiple access interference in truly asynchronous case is given. The bit error rate decreases as the ratio of the chip period to the root mean square delay spread increases and the channel limits the bit rate to different levels when the chip period varies.

Asynchronous Magnetic Bead Rotation (AMBR Microviscometer for Label-Free DNA Analysis

Directory of Open Access Journals (Sweden)

Yunzi Li

2014-03-01

Full Text Available We have developed a label-free viscosity-based DNA detection system, using paramagnetic beads as an asynchronous magnetic bead rotation (AMBR microviscometer. We have demonstrated experimentally that the bead rotation period is linearly proportional to the viscosity of a DNA solution surrounding the paramagnetic bead, as expected theoretically. Simple optical measurement of asynchronous microbead motion determines solution viscosity precisely in microscale volumes, thus allowing an estimate of DNA concentration or average fragment length. The response of the AMBR microviscometer yields reproducible measurement of DNA solutions, enzymatic digestion reactions, and PCR systems at template concentrations across a 5000-fold range. The results demonstrate the feasibility of viscosity-based DNA detection using AMBR in microscale aqueous volumes.

Flow characteristics and optimal design for RDT sparger

International Nuclear Information System (INIS)

Kim, Kwang Chu; Park, Man Heung; Park, Kyoung Suk; Lee, Jong Won

1999-01-01

A numerical analysis for RDT sparger of PWR is carried out. Computation is performed to investigate the flow characteristics as the change of design factor. As the result of this study, RDT sparger's flow resistance coefficient is K = 3.53 at the present design condition if engineering margin is considered with 20 percent, and flow ratio into branch pipe is Q s /Q i 0.41. Velocity distribution at exit is not uniform because of separation in branch pipe. In the change of inlet flow rate and second area ratio of branch pipe for main pipe, Flow resistance coefficient is increased as Q s /Q i decreasing, but in the change of branch angle and outlet nozzle diameter of main pipe, flow resistance coefficient is decreased as Q s /Q i decreasing. As the change rate of Q s /Q i is the larger, the change rate of flow resistance coefficient is the larger. The change rate of pressure loss is the largest change as section area ratio changing. The optimal design condition of sparger is estimated as the outlet nozzle diameter ratio of main pipe is D e /D i = 0.333, the second area ratio is A s /A i = 0.2 and the branch angle is α = 55 o . (author)

Optimization Design of Bipolar Plate Flow Field in PEM Stack

Science.gov (United States)

Wen, Ming; He, Kanghao; Li, Peilong; Yang, Lei; Deng, Li; Jiang, Fei; Yao, Yong

2017-12-01

A new design of bipolar plate flow field in proton exchange membrane (PEM) stack was presented to develop a high-performance transfer efficiency of the two-phase flow. Two different flow fields were studied by using numerical simulations and the performance of the flow fields was presented. the hydrodynamic properties include pressure gap between inlet and outlet, the Reynold’s number of the two types were compared based on the Navier-Stokes equations. Computer aided optimization software was implemented in the design of experiments of the preferable flow field. The design of experiments (DOE) for the favorable concept was carried out to study the hydrodynamic properties when changing the design parameters of the bipolar plate.

Asynchronous Multi-Party Computation with Quadratic Communication

DEFF Research Database (Denmark)

Hirt, Martin; Nielsen, Jesper Buus; Przydatek, Bartosz

2008-01-01

We present an efficient protocol for secure multi-party computation in the asynchronous model with optimal resilience. For n parties, up to t < n/3 of them being corrupted, and security parameter κ, a circuit with c gates can be securely computed with communication complexity O(cn^2k) bits, which...... circuit randomization due to Beaver (Crypto’91), and an abstraction of certificates, which can be of independent interest....

A modular control architecture for real-time synchronous and asynchronous systems

International Nuclear Information System (INIS)

Butler, P.L.; Jones, J.P.

1993-01-01

This paper describes a control architecture for real-time control of complex robotic systems. The Modular Integrated Control Architecture (MICA), which is actually two complementary control systems, recognizes and exploits the differences between asynchronous and synchronous control. The asynchronous control system simulates shared memory on a heterogeneous network. For control information, a portable event-scheme is used. This scheme provides consistent interprocess coordination among multiple tasks on a number of distributed systems. The machines in the network can vary with respect to their native operating systems and the intemal representation of numbers they use. The synchronous control system is needed for tight real-time control of complex electromechanical systems such as robot manipulators, and the system uses multiple processors at a specified rate. Both the synchronous and asynchronous portions of MICA have been developed to be extremely modular. MICA presents a simple programming model to code developers and also considers the needs of system integrators and maintainers. MICA has been used successfully in a complex robotics project involving a mobile 7-degree-of-freedom manipulator in a heterogeneous network with a body of software totaling over 100,000 lines of code. MICA has also been used in another robotics system, controlling a commercial long-reach manipulator

Full-load converter connected asynchronous generators for MW class wind turbines

Energy Technology Data Exchange (ETDEWEB)

Akhmatov, Vladislav

2005-06-15

Wind turbines equipped with full-load converter-connected asynchronous generators are a known concept. These have rating up to hundreds of kW and are a feasible concept for MW class wind turbines and may have advantages when compared to conventional wind turbines with directly connected generators. The concept requires the use of full-scale frequency converters, but the mechanical gearbox is smaller than in conventional wind turbines of the same rating. Application of smaller gearbox may reduce the no-load losses in the wind turbines, which is why such wind turbines with converter connected generators may start operation at a smaller wind speed. Wind turbines equipped with such converted connected asynchronous generators are pitch-controlled and variable-speed. This allows better performance and control. The converter control may be applied to support the grid voltage at short-circuit faults and to improve the fault-ride-through capability of the wind turbines, which makes the concepts relevant for large wind farms. The Danish transmission system operator Energinet-DK has implemented the general model of wind turbines equipped with converter connected asynchronous generators with the simulation tool Powerfactory (DlgSilent). The article presents Energinet-DK's experience of modeling this feasible wind turbine concept. (Author)

Turing Incompleteness of Asynchronous P Systems with Active Membranes

OpenAIRE

Leporati, Alberto; Manzoni, Luca; Porreca, Antonio E.

2013-01-01

We prove that asynchronous P systems with active membranes without divi- sion rules can be simulated by place/transition Petri nets, and hence are computationally weaker than Turing machines. This result holds even if the synchronisation mechanisms provided by electrical charges and membrane dissolution are exploited.

An improved modelling of asynchronous machine with skin-effect ...

African Journals Online (AJOL)

The conventional method of analysis of Asynchronous machine fails to give accurate results especially when the machine is operated under high rotor frequency. At high rotor frequency, skin-effect dominates causing the rotor impedance to be frequency dependant. This paper therefore presents an improved method of ...

Comparison between Synchronous and Asynchronous Instructional Delivery Method of Training Programme on In-Service Physical Educators' Knowledge

Science.gov (United States)

Emmanouilidou, Kyriaki; Derri, Vassiliki; Antoniou, Panagiotis; Kyrgiridis, Pavlos

2012-01-01

The purpose of the study was to compare the influences of a training programme's instructional delivery method (synchronous and asynchronous) on Greek in-service physical educators' cognitive understanding on student assessment. Forty nine participants were randomly divided into synchronous, asynchronous, and control group. The experimental groups…

Parallel, Asynchronous Executive (PAX): System concepts, facilities, and architecture

Science.gov (United States)

Jones, W. H.

1983-01-01

The Parallel, Asynchronous Executive (PAX) is a software operating system simulation that allows many computers to work on a single problem at the same time. PAX is currently implemented on a UNIVAC 1100/42 computer system. Independent UNIVAC runstreams are used to simulate independent computers. Data are shared among independent UNIVAC runstreams through shared mass-storage files. PAX has achieved the following: (1) applied several computing processes simultaneously to a single, logically unified problem; (2) resolved most parallel processor conflicts by careful work assignment; (3) resolved by means of worker requests to PAX all conflicts not resolved by work assignment; (4) provided fault isolation and recovery mechanisms to meet the problems of an actual parallel, asynchronous processing machine. Additionally, one real-life problem has been constructed for the PAX environment. This is CASPER, a collection of aerodynamic and structural dynamic problem simulation routines. CASPER is not discussed in this report except to provide examples of parallel-processing techniques.

Integration of asynchronous knowledge sources in a novel speech recognition framework

OpenAIRE

Van hamme, Hugo

2008-01-01

Van hamme H., ''Integration of asynchronous knowledge sources in a novel speech recognition framework'', Proceedings ITRW on speech analysis and processing for knowledge discovery, 4 pp., June 2008, Aalborg, Denmark.

The Design Method of Axial Flow Runners Focusing on Axial Flow Velocity Uniformization and Its Application to an Ultra-Small Axial Flow Hydraulic Turbine

Directory of Open Access Journals (Sweden)

Yasuyuki Nishi

2016-01-01

Full Text Available We proposed a portable and ultra-small axial flow hydraulic turbine that can generate electric power comparatively easily using the low head of open channels such as existing pipe conduits or small rivers. In addition, we proposed a simple design method for axial flow runners in combination with the conventional one-dimensional design method and the design method of axial flow velocity uniformization, with the support of three-dimensional flow analysis. Applying our design method to the runner of an ultra-small axial flow hydraulic turbine, the performance and internal flow of the designed runner were investigated using CFD analysis and experiment (performance test and PIV measurement. As a result, the runners designed with our design method were significantly improved in turbine efficiency compared to the original runner. Specifically, in the experiment, a new design of the runner achieved a turbine efficiency of 0.768. This reason was that the axial component of absolute velocity of the new design of the runner was relatively uniform at the runner outlet in comparison with that of the original runner, and as a result, the negative rotational flow was improved. Thus, the validity of our design method has been verified.

Specification and verification of gate-level VHDL models of synchronous and asynchronous circuits

Science.gov (United States)

Russinoff, David M.

1995-01-01

We present a mathematical definition of hardware description language (HDL) that admits a semantics-preserving translation to a subset of VHDL. Our HDL includes the basic VHDL propagation delay mechanisms and gate-level circuit descriptions. We also develop formal procedures for deriving and verifying concise behavioral specifications of combinational and sequential devices. The HDL and the specification procedures have been formally encoded in the computational logic of Boyer and Moore, which provides a LISP implementation as well as a facility for mechanical proof-checking. As an application, we design, specify, and verify a circuit that achieves asynchronous communication by means of the biphase mark protocol.

Asynchronous Message Service Reference Implementation

Science.gov (United States)

Burleigh, Scott C.

2011-01-01

This software provides a library of middleware functions with a simple application programming interface, enabling implementation of distributed applications in conformance with the CCSDS AMS (Consultative Committee for Space Data Systems Asynchronous Message Service) specification. The AMS service, and its protocols, implement an architectural concept under which the modules of mission systems may be designed as if they were to operate in isolation, each one producing and consuming mission information without explicit awareness of which other modules are currently operating. Communication relationships among such modules are self-configuring; this tends to minimize complexity in the development and operations of modular data systems. A system built on this model is a society of generally autonomous, inter-operating modules that may fluctuate freely over time in response to changing mission objectives, modules functional upgrades, and recovery from individual module failure. The purpose of AMS, then, is to reduce mission cost and risk by providing standard, reusable infrastructure for the exchange of information among data system modules in a manner that is simple to use, highly automated, flexible, robust, scalable, and efficient. The implementation is designed to spawn multiple threads of AMS functionality under the control of an AMS application program. These threads enable all members of an AMS-based, distributed application to discover one another in real time, subscribe to messages on specific topics, and to publish messages on specific topics. The query/reply (client/server) communication model is also supported. Message exchange is optionally subject to encryption (to support confidentiality) and authorization. Fault tolerance measures in the discovery protocol minimize the likelihood of overall application failure due to any single operational error anywhere in the system. The multi-threaded design simplifies processing while enabling application nodes to

Highly Scalable Asynchronous Computing Method for Partial Differential Equations: A Path Towards Exascale

Science.gov (United States)

Konduri, Aditya

Many natural and engineering systems are governed by nonlinear partial differential equations (PDEs) which result in a multiscale phenomena, e.g. turbulent flows. Numerical simulations of these problems are computationally very expensive and demand for extreme levels of parallelism. At realistic conditions, simulations are being carried out on massively parallel computers with hundreds of thousands of processing elements (PEs). It has been observed that communication between PEs as well as their synchronization at these extreme scales take up a significant portion of the total simulation time and result in poor scalability of codes. This issue is likely to pose a bottleneck in scalability of codes on future Exascale systems. In this work, we propose an asynchronous computing algorithm based on widely used finite difference methods to solve PDEs in which synchronization between PEs due to communication is relaxed at a mathematical level. We show that while stability is conserved when schemes are used asynchronously, accuracy is greatly degraded. Since message arrivals at PEs are random processes, so is the behavior of the error. We propose a new statistical framework in which we show that average errors drop always to first-order regardless of the original scheme. We propose new asynchrony-tolerant schemes that maintain accuracy when synchronization is relaxed. The quality of the solution is shown to depend, not only on the physical phenomena and numerical schemes, but also on the characteristics of the computing machine. A novel algorithm using remote memory access communications has been developed to demonstrate excellent scalability of the method for large-scale computing. Finally, we present a path to extend this method in solving complex multi-scale problems on Exascale machines.

Asynchronous P300-based brain-computer interface to control a virtual environment: initial tests on end users.

Science.gov (United States)

Aloise, Fabio; Schettini, Francesca; Aricò, Pietro; Salinari, Serenella; Guger, Christoph; Rinsma, Johanna; Aiello, Marco; Mattia, Donatella; Cincotti, Febo

2011-10-01

Motor disability and/or ageing can prevent individuals from fully enjoying home facilities, thus worsening their quality of life. Advances in the field of accessible user interfaces for domotic appliances can represent a valuable way to improve the independence of these persons. An asynchronous P300-based Brain-Computer Interface (BCI) system was recently validated with the participation of healthy young volunteers for environmental control. In this study, the asynchronous P300-based BCI for the interaction with a virtual home environment was tested with the participation of potential end-users (clients of a Frisian home care organization) with limited autonomy due to ageing and/or motor disabilities. System testing revealed that the minimum number of stimulation sequences needed to achieve correct classification had a higher intra-subject variability in potential end-users with respect to what was previously observed in young controls. Here we show that the asynchronous modality performed significantly better as compared to the synchronous mode in continuously adapting its speed to the users' state. Furthermore, the asynchronous system modality confirmed its reliability in avoiding misclassifications and false positives, as previously shown in young healthy subjects. The asynchronous modality may contribute to filling the usability gap between BCI systems and traditional input devices, representing an important step towards their use in the activities of daily living.

Asynchronous data change notification between database server and accelerator controls system

International Nuclear Information System (INIS)

Fu, W.; Morris, J.; Nemesure, S.

2011-01-01

Database data change notification (DCN) is a commonly used feature. Not all database management systems (DBMS) provide an explicit DCN mechanism. Even for those DBMS's which support DCN (such as Oracle and MS SQL server), some server side and/or client side programming may be required to make the DCN system work. This makes the setup of DCN between database server and interested clients tedious and time consuming. In accelerator control systems, there are many well established software client/server architectures (such as CDEV, EPICS, and ADO) that can be used to implement data reflection servers that transfer data asynchronously to any client using the standard SET/GET API. This paper describes a method for using such a data reflection server to set up asynchronous DCN (ADCN) between a DBMS and clients. This method works well for all DBMS systems which provide database trigger functionality. Asynchronous data change notification (ADCN) between database server and clients can be realized by combining the use of a database trigger mechanism, which is supported by major DBMS systems, with server processes that use client/server software architectures that are familiar in the accelerator controls community (such as EPICS, CDEV or ADO). This approach makes the ADCN system easy to set up and integrate into an accelerator controls system. Several ADCN systems have been set up and used in the RHIC-AGS controls system.

Continuous EEG signal analysis for asynchronous BCI application.

Science.gov (United States)

Hsu, Wei-Yen

2011-08-01

In this study, we propose a two-stage recognition system for continuous analysis of electroencephalogram (EEG) signals. An independent component analysis (ICA) and correlation coefficient are used to automatically eliminate the electrooculography (EOG) artifacts. Based on the continuous wavelet transform (CWT) and Student's two-sample t-statistics, active segment selection then detects the location of active segment in the time-frequency domain. Next, multiresolution fractal feature vectors (MFFVs) are extracted with the proposed modified fractal dimension from wavelet data. Finally, the support vector machine (SVM) is adopted for the robust classification of MFFVs. The EEG signals are continuously analyzed in 1-s segments, and every 0.5 second moves forward to simulate asynchronous BCI works in the two-stage recognition architecture. The segment is first recognized as lifted or not in the first stage, and then is classified as left or right finger lifting at stage two if the segment is recognized as lifting in the first stage. Several statistical analyses are used to evaluate the performance of the proposed system. The results indicate that it is a promising system in the applications of asynchronous BCI work.

Sum rates of asynchronous GFDMA and SC-FDMA for 5G uplink

Directory of Open Access Journals (Sweden)

Woojin Park

2015-12-01

Full Text Available The fifth generation (5G of mobile communication envisions ultralow latency less than 1 ms for radio interface. To this end, frameless asynchronous multiple access may be needed to allow users to transmit instantly without waiting for the next frame start. In this paper, generalized frequency division multiple-access (GFDMA, one of the promising multiple-access candidates for 5G mobile, is compared with the conventional single-carrier FDMA (SC-FDMA in terms of the uplink sum rate when both techniques are adapted for the asynchronous scenario. In particular, a waveform windowing technique is applied to both schemes to mitigate the inter-user interference due to non-zero out-of-band emission.

High-speed asynchronous optical sampling for high-sensitivity detection of coherent phonons

International Nuclear Information System (INIS)

Dekorsy, T; Taubert, R; Hudert, F; Schrenk, G; Bartels, A; Cerna, R; Kotaidis, V; Plech, A; Koehler, K; Schmitz, J; Wagner, J

2007-01-01

A new optical pump-probe technique is implemented for the investigation of coherent acoustic phonon dynamics in the GHz to THz frequency range which is based on two asynchronously linked femtosecond lasers. Asynchronous optical sampling (ASOPS) provides the performance of on all-optical oscilloscope and allows us to record optically induced lattice dynamics over nanosecond times with femtosecond resolution at scan rates of 10 kHz without any moving part in the set-up. Within 1 minute of data acquisition time signal-to-noise ratios better than 10 7 are achieved. We present examples of the high-sensitivity detection of coherent phonons in superlattices and of the coherent acoustic vibration of metallic nanoparticles

Design flow factors for sewerage systems in small arid communities

Directory of Open Access Journals (Sweden)

Emad H. Imam

2014-09-01

Full Text Available Reliable estimation of sewage flow rates is essential for the proper design of sewers, pumping stations, and treatment plants. The design of the various components of the sewerage system should be based on the most critical flow rates with a focus on extremely low and peak flow rates that would be sustained for a duration related to the acceptable limits of behavior of the components under consideration. The extreme flow conditions and to what extent they differ from the average values are closely related to the size of the community or network, and the socioeconomic conditions. A single pumping station is usually sufficient to pump flow from small community in either flat or non-undulating topography. Therefore, the hydraulic loading on the wastewater treatment plant (WWTP results from the pumped flow from the pumping station rather than the trunk sewer flow. The intermittent operation of the pumping units further accentuates the sewage hydrograph in the final trunk sewer. Accordingly, the design flow for the various components of the WWTP should be determined based on their relevant flow factors. In this study, analysis of one representative small community out of five monitored small communities in Egypt and the Kingdom of Saudi Arabia is presented. Pumped sewage flow rates were measured and the sewer incoming flows were hydraulically derived. The hourly and daily sewer and pumped flow records were analyzed to derive the relationship between the flow factors that would be sustained for various durations (instantaneously, 1 h, 2 h, etc. and their probability of non-exceedance. The resulting peaking factors with a consideration for their sustained flow duration and specified probability would permit the design of the various components of the treatment plant using more accurate critical flows.

Design flow factors for sewerage systems in small arid communities.

Science.gov (United States)

Imam, Emad H; Elnakar, Haitham Y

2014-09-01

Reliable estimation of sewage flow rates is essential for the proper design of sewers, pumping stations, and treatment plants. The design of the various components of the sewerage system should be based on the most critical flow rates with a focus on extremely low and peak flow rates that would be sustained for a duration related to the acceptable limits of behavior of the components under consideration. The extreme flow conditions and to what extent they differ from the average values are closely related to the size of the community or network, and the socioeconomic conditions. A single pumping station is usually sufficient to pump flow from small community in either flat or non-undulating topography. Therefore, the hydraulic loading on the wastewater treatment plant (WWTP) results from the pumped flow from the pumping station rather than the trunk sewer flow. The intermittent operation of the pumping units further accentuates the sewage hydrograph in the final trunk sewer. Accordingly, the design flow for the various components of the WWTP should be determined based on their relevant flow factors. In this study, analysis of one representative small community out of five monitored small communities in Egypt and the Kingdom of Saudi Arabia is presented. Pumped sewage flow rates were measured and the sewer incoming flows were hydraulically derived. The hourly and daily sewer and pumped flow records were analyzed to derive the relationship between the flow factors that would be sustained for various durations (instantaneously, 1 h, 2 h, etc.) and their probability of non-exceedance. The resulting peaking factors with a consideration for their sustained flow duration and specified probability would permit the design of the various components of the treatment plant using more accurate critical flows.

Knowledge Flow Rules of Modern Design under Distributed Resource Environment

Directory of Open Access Journals (Sweden)

Junning Li

2013-01-01

Full Text Available The process of modern design under the distributed resource environment is interpreted as the process of knowledge flow and integration. As the acquisition of new knowledge strongly depends on resources, knowledge flow can be influenced by technical, economic, and social relation factors, and so forth. In order to achieve greater efficiency of knowledge flow and make the product more competitive, the root causes of the above factors should be acquired first. In this paper, the authors attempt to reveal the nature of design knowledge flow from the perspectives of fluid dynamics and energy. The knowledge field effect and knowledge agglomeration effect are analyzed, respectively, in which the knowledge field effect model considering single task node and the single knowledge energy model in the knowledge flow are established, then the general expression of knowledge energy conservation with consideration of the kinetic energy and potential energy of knowledge is built. Then, the knowledge flow rules and their influential factors including complete transfer and incomplete transfer of design knowledge are studied. Finally, the coupling knowledge flows in the knowledge service platform for modern design are analyzed to certify the feasibility of the research work.

The aspect of vector control using the asynchronous traction motor in locomotives

Directory of Open Access Journals (Sweden)

L. Liudvinavičius

2009-12-01

Full Text Available The article examines curves controlling asynchronous traction motors increasingly used in locomotive electric drives the main task of which is to create a tractive effort-speed curve of an ideal locomotive Fk = f(v, including a hyperbolic area the curve of which will create conditions showing that energy created by the diesel engine of diesel locomotives (electric locomotives and in case of electric trains, electricity taken from the contact network over the entire range of locomotive speed is turned into efficient work. Mechanical power on wheel sets is constant Pk = Fkv = const, the power of the diesel engine is fully used over the entire range of locomotive speed. Tractive effort-speed curve Fk(v shows the dependency of locomotive traction power Fk on movement speed v. The article presents theoretical and practical aspects relevant to creating the structure of locomotive electric drive and selecting optimal control that is especially relevant to creating the structure of locomotive electric drive using ATM (asynchronous traction motor that gains special popularity in traction rolling stock replacing DC traction motors having low reliability. The frequency modes of asynchronous motor speed regulation are examined. To control ATM, the authors suggest the method of vector control presenting the structural schemes of a locomotive with ATM and control algorithm.

Chick Development and Asynchroneous Hatching in the Zebra Finch (Taeniopygia guttata castanotis).

Science.gov (United States)

Ikebuchi, Maki; Okanoya, Kazuo; Hasegawa, Toshikazu; Bischof, Hans-Joachim

2017-10-01

The mode of hatching in birds has important impacts on both parents and chicks, including the costs and risks of breeding for parents, and sibling competition in a clutch. Birds with multiple eggs in a single clutch often begin incubating when most eggs are laid, thereby reducing time of incubation, nursing burden, and sibling competition. In some songbirds and some other species, however, incubation starts immediately after the first egg is laid, and the chicks thus hatch asynchronously. This may result in differences in parental care and in sibling competition based on body size differences among older and younger chicks, which in turn might produce asynchronous development among siblings favoring the first hatchling, and further affect the development and fitness of the chicks after fledging. To determine whether such processes in fact occur in the zebra finch, we observed chick development in 18 clutches of zebra finches. We found that there were effects of asynchronous hatching, but these were smaller than expected and mostly not significant. Our observations suggest that the amount of care given to each chick may be equated with such factors as a camouflage effect of the down feathers, and that the low illumination within the nest also complicates the determination of the hatching order by the parents.

Asynchronous Cholinergic Drive Correlates with Excitation-Inhibition Imbalance via a Neuronal Ca2+ Sensor Protein

Directory of Open Access Journals (Sweden)

Keming Zhou

2017-05-01

Full Text Available Excitation-inhibition imbalance in neural networks is widely linked to neurological and neuropsychiatric disorders. However, how genetic factors alter neuronal activity, leading to excitation-inhibition imbalance, remains unclear. Here, using the C. elegans locomotor circuit, we examine how altering neuronal activity for varying time periods affects synaptic release pattern and animal behavior. We show that while short-duration activation of excitatory cholinergic neurons elicits a reversible enhancement of presynaptic strength, persistent activation results to asynchronous and reduced cholinergic drive, inducing imbalance between endogenous excitation and inhibition. We find that the neuronal calcium sensor protein NCS-2 is required for asynchronous cholinergic release in an activity-dependent manner and dampens excitability of inhibitory neurons non-cell autonomously. The function of NCS-2 requires its Ca2+ binding and membrane association domains. These results reveal a synaptic mechanism implicating asynchronous release in regulation of excitation-inhibition balance.

Asynchronous online foresight panels: the case of wildfire management

Science.gov (United States)

David N. Bengston; Robert L. Olson

2015-01-01

Text-based asynchronous online conferencing involves structured online discussion and deliberation among multiple participants from multiple sites in which there is a delay in interaction between contributors. This method has been widely used for a variety of purposes in higher education and other settings, but has not been commonly used in futures research. This paper...

Students experiences with collaborative learning in asynchronous computer-supported collaborative learning environments.

NARCIS (Netherlands)

Dewiyanti, Silvia; Brand-Gruwel, Saskia; Jochems, Wim; Broers, Nick

2008-01-01

Dewiyanti, S., Brand-Gruwel, S., Jochems, W., & Broers, N. (2007). Students experiences with collaborative learning in asynchronous computer-supported collaborative learning environments. Computers in Human Behavior, 23, 496-514.

Novel biometric flow slab design for improvement of PEMFC performance

Energy Technology Data Exchange (ETDEWEB)

Wang, Chin-Tsan; Hu, Yuh-Chung; Zheng, Pei-Lun [Department of Mechanical and Electro-Mechanical Engineering, Center of Green Technology, National I Lan University, I Lan 26047 (China)

2010-04-15

Designing a better flow slab is important to cell performance because of its significant influence on the total pressure drop and flow uniformity. Two novel biometric flow slabs, BFF1 and BFF2, which are addressed in this study, are believed to enhance the capability of oxygen transportation and promote the liquid water removal. Hence, its possession of a higher flow uniformity and lower pressure drop would produce a better power performance than the serpentine and parallel flow. These findings with respect to the design of biometric flow slab could be useful to promote the cell performance of PEMFC, and could even be expanded to other cell types. (author)

Reconceptualising Moderation in Asynchronous Online Discussions Using Grounded Theory

Science.gov (United States)

Vlachopoulos, Panos; Cowan, John

2010-01-01

This article reports a grounded theory study of the moderation of asynchronous online discussions, to explore the processes by which tutors in higher education decide when and how to moderate. It aims to construct a theory of e-moderation based on some key factors which appear to influence e-moderation. It discusses previous research on the…

Developing a Successful Asynchronous Online Extension Program for Forest Landowners

Science.gov (United States)

Zobrist, Kevin W.

2014-01-01

Asynchronous online Extension classes can reach a wide audience, is convenient for the learner, and minimizes ongoing demands on instructor time. However, producing such classes takes significant effort up front. Advance planning and good communication with contributors are essential to success. Considerations include delivery platforms, content…

Asynchronous teaching of psychomotor skills through VR annotations: evaluation in digital rectal examination.

Science.gov (United States)

Rissanen, Mikko J; Kume, Naoto; Kuroda, Yoshihiro; Kuroda, Tomohiro; Yoshimura, Koji; Yoshihara, Hiroyuki

2008-01-01

Many VR technology based training systems use expert's motion data as the training aid, but would not provide any short-cut to teaching medical skills that do not depend on exact motions. Earlier we presented Annotated Simulation Records (ASRs), which can be used to encapsulate experts' insight on psychomotor skills. Annotations made to behavioural parameters in training simulators enable asynchronous teaching instead of just motion training in a proactive way to the learner. We evaluated ASRs for asynchronous teaching of Digital Rectal Examination (DRE) with 3 urologists and 8 medical students. The ASRs were found more effective than motion-based training with verbal feedback.

Algebraic Number Precoded OFDM Transmission for Asynchronous Cooperative Multirelay Networks

Directory of Open Access Journals (Sweden)

Hua Jiang

2014-01-01

Full Text Available This paper proposes a space-time block coding (STBC transmission scheme for asynchronous cooperative systems. By combination of rotated complex constellations and Hadamard transform, these constructed codes are capable of achieving full cooperative diversity with the analysis of the pairwise error probability (PEP. Due to the asynchronous characteristic of cooperative systems, orthogonal frequency division multiplexing (OFDM technique with cyclic prefix (CP is adopted for combating timing delays from relay nodes. The total transmit power across the entire network is fixed and appropriate power allocation can be implemented to optimize the network performance. The relay nodes do not require decoding and demodulation operation, resulting in a low complexity. Besides, there is no delay for forwarding the OFDM symbols to the destination node. At the destination node the received signals have the corresponding STBC structure on each subcarrier. In order to reduce the decoding complexity, the sphere decoder is implemented for fast data decoding. Bit error rate (BER performance demonstrates the effectiveness of the proposed scheme.

Design flow factors for sewerage systems in small arid communities

OpenAIRE

Imam, Emad H.; Elnakar, Haitham Y.

2014-01-01

Reliable estimation of sewage flow rates is essential for the proper design of sewers, pumping stations, and treatment plants. The design of the various components of the sewerage system should be based on the most critical flow rates with a focus on extremely low and peak flow rates that would be sustained for a duration related to the acceptable limits of behavior of the components under consideration. The extreme flow conditions and to what extent they differ from the average values are cl...

Modeling the Design Flow Coefficient of a Centrifugal Compressor Impeller

Directory of Open Access Journals (Sweden)

A. A. Drozdov

2017-01-01

Full Text Available In calculating gas-dynamic characteristics by the universal modeling method it is necessary to determine a non-incidence flow rate through the blades of an impeller because of its relationship with the magnitude of incidence losses. The flow area decreased by the blades of finite thickness and the blades load have impact on the critical streamline direction. The universal modeling method in primary designing uses for this a scheme of replacing the influence of the blade load by the vortex effect with identical circulation. Finally, calculating the inviscid flow around the blades allows selecting a value of the inlet blade angle. For impellers with small design flow coefficients, the condition of the non-incidence inlet for the primary design and for the calculation of the inviscid flow is significantly different. The calculating correctness of the non-incidence regime for the non-viscous flow was checked earlier by measurements of the flow in the impellers. The paper presents CFD calculations of twenty impellers in a tenfold range of design flow coefficients. To provide correct comparison, it takes into account the differences in the value of the loading factor calculated by the programs of inviscid quasi-three-dimensional calculation and CFD programs. Shows the identity of inlet conditions for both methods. To increase primary design accuracy, the calculation model was refined. The formula for calculating vortex-induced velocity involves an empirical coefficient. The analysis of data for 32 impellers with different blade profiling allowed working out formulas for calculating empirical coefficient, depending on the type of an impeller, the blade load and the width of the throat at an impeller inlet. The new scheme-based calculation with the empirical coefficient is accurate enough for the primary design.

Involving the users remotely: an exploratory study using asynchronous usability testing

Directory of Open Access Journals (Sweden)

Beth Filar Williams

2015-02-01

Full Text Available Open Educational Resources (OER are increasingly used in the higher education landscape as a solution for a variety of copyright, publishing and cost-prohibiting issues. While OERs are becoming more common, reports of usability tests that evaluate how well learners can use them to accomplish their learning tasks have lagged behind. Because both the researchers and the learners in this study use resources and tools remotely, asynchronous usability testing of a prototype OER and MOOC online guide was conducted with an exploratory group of users to determine the guide’s ease of use for two distinct groups of users: Educators and Learners. In this article, we share the background and context of this usability project, suggest best methods for asynchronous remote usability testing, and share challenges and insights of the process and results of the testing

An asynchronous, pipelined, electronic acquisition system for Active Matrix Flat-Panel Imagers (AMFPIs)

CERN Document Server

Huang, W; Berry, J; Maolinbay, M; Martelli, C; Mody, P; Nassif, S; Yeakey, M

1999-01-01

The development of a full-custom electronic acquisition system designed for readout of large-area active matrix flat-panel imaging arrays is reported. The arrays, which comprise two-dimensional matrices of pixels utilizing amorphous silicon thin-film transistors, are themselves under development for a wide variety of X-ray imaging applications. The acquisition system was specifically designed to facilitate detailed, quantitative investigations of the properties of these novel imaging arrays and contains significant enhancements compared to a previously developed acquisition system. These enhancements include pipelined preamplifier circuits to allow faster readout speed, expanded addressing capabilities allowing a maximum of 4096 array data lines, and on-board summing of image frames. The values of many acquisition system parameters, including timings and voltages, may be specified and downloaded from a host computer. Once acquisition is enabled, the system operates asynchronously of its host computer. The sys...

Topology optimization considering design-dependent Stokes flow loads

NARCIS (Netherlands)

Picelli, R.; Vicente, W.M.; Pavanello, R.; van Keulen, A.; Li, Qing; Steven, Grant P.; Zhang, Zhongpu

2015-01-01

This article presents an evolutionary topology optimization method for mean compliance minimization of structures under design-dependent viscous fluid flow loads. The structural domain is governed by the elasticity equation and the fluid by the incompressible Stokes flow equations. When the

Asynchronous Group Review of EFL Writing: Interactions and Text Revisions

Science.gov (United States)

Saeed, Murad Abdu; Ghazali, Kamila

2017-01-01

The current paper reports an empirical study of asynchronous online group review of argumentative essays among nine English as foreign language (EFL) Arab university learners joining English in their first, second, and third years at the institution. In investigating online interactions, commenting patterns, and how the students facilitate text…

Multithreaded Asynchronous Graph Traversal for In-Memory and Semi-External Memory

KAUST Repository

Pearce, Roger; Gokhale, Maya; Amato, Nancy M.

2010-01-01

. Our highly parallel asynchronous approach hides data latency due to both poor locality and delays in the underlying graph data storage. We present an experimental study applying our technique to both In-Memory and Semi-External Memory graphs utilizing

Massive Asynchronous Parallelization of Sparse Matrix Factorizations

Energy Technology Data Exchange (ETDEWEB)

Chow, Edmond [Georgia Inst. of Technology, Atlanta, GA (United States)

2018-01-08

Solving sparse problems is at the core of many DOE computational science applications. We focus on the challenge of developing sparse algorithms that can fully exploit the parallelism in extreme-scale computing systems, in particular systems with massive numbers of cores per node. Our approach is to express a sparse matrix factorization as a large number of bilinear constraint equations, and then solving these equations via an asynchronous iterative method. The unknowns in these equations are the matrix entries of the factorization that is desired.

Parallel asynchronous hardware implementation of image processing algorithms

Science.gov (United States)

Coon, Darryl D.; Perera, A. G. U.

1990-01-01

Research is being carried out on hardware for a new approach to focal plane processing. The hardware involves silicon injection mode devices. These devices provide a natural basis for parallel asynchronous focal plane image preprocessing. The simplicity and novel properties of the devices would permit an independent analog processing channel to be dedicated to every pixel. A laminar architecture built from arrays of the devices would form a two-dimensional (2-D) array processor with a 2-D array of inputs located directly behind a focal plane detector array. A 2-D image data stream would propagate in neuron-like asynchronous pulse-coded form through the laminar processor. No multiplexing, digitization, or serial processing would occur in the preprocessing state. High performance is expected, based on pulse coding of input currents down to one picoampere with noise referred to input of about 10 femtoamperes. Linear pulse coding has been observed for input currents ranging up to seven orders of magnitude. Low power requirements suggest utility in space and in conjunction with very large arrays. Very low dark current and multispectral capability are possible because of hardware compatibility with the cryogenic environment of high performance detector arrays. The aforementioned hardware development effort is aimed at systems which would integrate image acquisition and image processing.

Formation of the wide asynchronous binary asteroid population

International Nuclear Information System (INIS)

Jacobson, Seth A.; Scheeres, Daniel J.; McMahon, Jay

2014-01-01

We propose and analyze a new mechanism for the formation of the wide asynchronous binary population. These binary asteroids have wide semimajor axes relative to most near-Earth and main belt asteroid systems. Confirmed members have rapidly rotating primaries and satellites that are not tidally locked. Previously suggested formation mechanisms from impact ejecta, from planetary flybys, and directly from rotational fission events cannot satisfy all of the observations. The newly hypothesized mechanism works as follows: (1) these systems are formed from rotational fission, (2) their satellites are tidally locked, (3) their orbits are expanded by the binary Yarkovsky-O'Keefe-Radzievskii-Paddack (BYORP) effect, (4) their satellites desynchronize as a result of the adiabatic invariance between the libration of the secondary and the mutual orbit, and (5) the secondary avoids resynchronization because of the YORP effect. This seemingly complex chain of events is a natural pathway for binaries with satellites that have particular shapes, which define the BYORP effect torque that acts on the system. After detailing the theory, we analyze each of the wide asynchronous binary members and candidates to assess their most likely formation mechanism. Finally, we suggest possible future observations to check and constrain our hypothesis.

Pedagogical dimensions of effective online asynchronous teacher communication in higher education

NARCIS (Netherlands)

Smits, A.; Voogt, J.; Rutledge, D.; Slykhuis, D.

2015-01-01

In this research teacher behaviour in online asynchronous discussions is studied. To this end teachers’ online messages were analyzed and correlated to measures of student satisfaction. Findings show a positive relation between student satisfaction and the presence of content knowledge, multiple

Flow in a centrifugal fan impeller at off-design conditions

Science.gov (United States)

Wright, T.; Tzou, K. T. S.; Madhavan, S.

1984-06-01

A fully three-dimensional finite element analysis of inviscid, incompressible blade channel flow is the basis of the present study of both predicted and measured surface velocity and pressure distributions in the internal flow channels of a centrifugal fan impeller, for volume flow rates of 80-125 percent the design flow rate. The experimental results made extensive use of blade and sidewall surface pressure taps installed in a scale model of an airfoil-bladed centrifugal fan impeller. The results obtained illustrate the ability of both flow analyses to predict the dominant features of the impeller flow field, including peak blade surface velocities and adverse gradients at flows far from the design point. Insight is also gained into the limiting channel diffusion values for typical centrifugal cascade performance, together with the influence of viscous effects, as seen in deviations from ideal flow predictions.

Student participation and interactivity using asynchronous computer-mediated communication for resolution of an undergraduate capstone management case study.

Science.gov (United States)

Miller, Paulette J

2012-01-01

Online discussion activities are designed for computer-mediated learning activities in face-to-face, hybrid, and totally online courses. The use of asynchronous computer-mediated communication (A-CMC) coupled with authentic workplace case studies provides students in the protected learning environment with opportunities to practice workplace decision making and communication. In this study, communication behaviors of transmitter and receiver were analyzed to determine participation and interactivity in communication among small-group participants in a health information management capstone management course.

The synthesis method for design of electron flow sources

Science.gov (United States)

Alexahin, Yu I.; Molodozhenzev, A. Yu

1997-01-01

The synthesis method to design a relativistic magnetically - focused beam source is described in this paper. It allows to find a shape of electrodes necessary to produce laminar space charge flows. Electron guns with shielded cathodes designed with this method were analyzed using the EGUN code. The obtained results have shown the coincidence of the synthesis and analysis calculations [1]. This method of electron gun calculation may be applied for immersed electron flows - of interest for the EBIS electron gun design.

Students' Learning in Asynchronous Discussion Forums: A Meta-Analysis

Science.gov (United States)

Martono, Fkipuntan; Salam, Urai

2017-01-01

Asynchronous discussion forums are among the most preferred tools chosen to foster learning opportunities and knowledge construction. To reveal the cognitive engagement evidenced in the transcripts of the discussion forums, this study presents 51 papers. 17 papers reported research on students' attitude toward the use of ICT for learning, 16…

Clonal expansion and linear genome evolution through breast cancer progression from pre-invasive stages to asynchronous metastasis

DEFF Research Database (Denmark)

Krøigård, Anne Bruun; Larsen, Martin Jakob; Lænkholm, Anne Vibeke

2015-01-01

Evolution of the breast cancer genome from pre-invasive stages to asynchronous metastasis is complex and mostly unexplored, but highly demanded as it may provide novel markers for and mechanistic insights in cancer progression. The increasing use of personalized therapy of breast cancer necessita......Evolution of the breast cancer genome from pre-invasive stages to asynchronous metastasis is complex and mostly unexplored, but highly demanded as it may provide novel markers for and mechanistic insights in cancer progression. The increasing use of personalized therapy of breast cancer...... progression from one breast cancer patient, including two different regions of Ductal Carcinoma In Situ (DCIS), primary tumor and an asynchronous metastasis. We identify a remarkable landscape of somatic mutations, retained throughout breast cancer progression and with new mutational events emerging at each...

Design and construction of two phases flow meter

International Nuclear Information System (INIS)

Nor Paiza Mohamad Hasan

2002-01-01

This paper deals with design of the gamma ray correlometer and flow loop system for measuring the velocity between two parallel cross-sections of a pipeline. In the laboratory, the radioisotope source and detector were collimated by brass with small beam slit respectively. The flow loop system consists of transparent pipeline, adjustable frequency pump and water container. As a result, when the construction of the flow loop and correlometer is completed, the velocity of two phases flow can be measured by the cross-correlation techniques. (Author)

Design concept of the HPLWR moderator flow path

International Nuclear Information System (INIS)

Koehly, Christina; Schulenberg, Thomas; Starflinger, Joerg

2009-01-01

The latest design concept of the High Performance Light Water Reactor (HPLWR) includes a thermal core in which supercritical water at 25 MPa inlet pressure is heated up from 280degC reactor inlet temperature to 500degC core exit temperature in three steps with intermediate coolant mixing to minimize peak cladding temperatures of the fuel rods. Prior to entering the first fuel assemblies, the coolant is used as moderator in water rods inside assemblies, in the gap volume between assembly boxes, as well as in the surrounding axial or radial reflectors. Even though assembly boxes and moderator rods are designed with a certain thermal insulation, heat is generated in the moderator water or transferred to it from the superheated steam inside assemblies, causing concern of natural convection phenomena with uncontrolled neutronic feedback on the core power distribution. Moreover, bypass flows of the moderator water need to be minimized at any thermal expansion of the reactor internal structures to avoid an unpredictable moderator mass flow. The design concept of the moderator flow path described in this paper is trying to overcome these problems. Downward flow of moderator water is limited to sub-cooled conditions, well below the pseudo-critical point of supercritical water. Dedicated orifices are foreseen to allow later correction of the mass flow split. The sealing concept accounts for larger thermal expansions of reactor components by using C-rings or bellows. A welded construction is preferred wherever possible to minimize leakage. The removable steam plenum is aligned at the extractable steam pipes to minimize thermal displacements at the sealing positions. The paper is showing several design details to illustrate the technical solutions. (author)

Wind generator based on cascade connection of two asynchronized synchronous machines

International Nuclear Information System (INIS)

Dzhagarov, N.; Dzhagarova, Yu.

2000-01-01

A model of a wind generator with two asynchronized synchronous machines presented and different regimes are investigated. The analysis shows that the suggested scheme of a brushless generator works and has more advantages (reliability, easy for operation) in comparison with the known ones

Unsteady Flow Dynamics and Acoustics of Two-Outlet Centrifugal Fan Design

Science.gov (United States)

Wong, I. Y. W.; Leung, R. C. K.; Law, A. K. Y.

2011-09-01

In this study, a centrifugal fan design with two flow outlets is investigated. This design aims to provide high mass flow rate but low noise performance. Two dimensional unsteady flow simulation with CFD code (FLUENT 6.3) is carried out to analyze the fan flow dynamics and its acoustics. The calculations were done using the unsteady Reynolds averaged Navier Stokes (URANS) approach in which effects of turbulence were accounted for using κ-ɛ model. This work aims to provide an insight how the dominant noise source mechanisms vary with a key fan geometrical paramters, namely, the ratio between cutoff distance and the radius of curvature of the fan housing. Four new fan designs were calculated. Simulation results show that the unsteady flow-induced forces on the fan blades are found to be the main noise sources. The blade force coefficients are then used to build the dipole source terms in Ffowcs Williams and Hawkings (FW-H) Equation for estimating their noise effects. It is found that one design is able to deliver a mass flow 34% more, but with sound pressure level (SPL) 10 dB lower, than the existing design .

Fluka studies of the Asynchronous Beam Dump Effects on LHC Point 6

CERN Document Server

Versaci, R; Goddard, B; Mereghetti, A; Schmidt, R; Vlachoudis, V; CERN. Geneva. ATS Department

2011-01-01

The LHC is a record-breaking machine for beam energy and intensity. An intense effort has therefore been deployed in simulating critical operational scenarios of energy deposition. Using FLUKA Monte Carlo simulations, we have investigated the effects of an asynchronous beam dump at the LHC Point 6 where beams, with a stored energy of 360 MJ, can instantaneously release up to a few J cm^-3 in the cryogenic magnets which have a quench limit of the order of the mJ cm^-3. In the present paper we will describe the simulation approach, and discuss the evaluated maximum energy release onto the superconducting magnets during an asynchronous beam dump. We will then analyze the shielding provided by collimators installed in the area and discuss safety limits for the operation of the LHC.

Blade design loads on the flow exciting force in centrifugal pump

International Nuclear Information System (INIS)

Xu, Y; Yang, A L; Langand, D P; Dai, R

2012-01-01

The three-dimensional viscous flow field of two centrifugal pumps, which have the same volute, design head, design flow rate and rotational speed but the blade design load, are analyzed based on large eddy simulation. The comparisons are implemented including the hydraulic efficiencies, flow field characteristics, pressure pulsations and unsteady forces applied on the impellers to investigate the effect of the design blade load on hydraulic performance and flow exciting force. The numerical results show that the efficiency of the pump, the impeller blade of which has larger design load, is improved by 1.1%∼2.9% compared to the centrifugal pump with lower blade design load. The pressure fluctuation of the pump with high design load is more remarkable. Its maximum amplitude of coefficient of static pressure is higher by 43% than the latter. At the same time the amplitude of unsteady radial force is increased by 11.6% in the time domain. The results also imply that the blade design load is an important factor on the excitation force in centrifugal pumps.

Preparation for an online asynchronous university doctoral course. Lessons learned.

Science.gov (United States)

Milstead, J A; Nelson, R

1998-01-01

This article addresses the development of the initial course in the first completely online doctoral program in nursing. Synchronous and asynchronous methods of distance education were assessed. Planning focused at the university, school, and course levels. University planning involved the technical infrastructure, registration, student services, and library services. School planning examined administrative commitment and faculty commitment and willingness. Course planning focused on marketing, precourse information, time frame, modular design, planned interaction, and professor availability and support. Implementation issues centered on getting students connected, learning the software, changing instructional methods, and managing chats. Traditional methods of evaluating student learning and course evaluation were supplemented with the development of qualitative and quantitative tools to gather data for making administrative decisions. The Dean and faculty agreed that the internet was an effective method of delivering content in the initial Health Policy course. The Dean and faculty agreed to continue the PhD program online for one cohort and continue to evaluate student progress and faculty and student satisfaction.

An Asynchronous P300 BCI With SSVEP-Based Control State Detection

DEFF Research Database (Denmark)

Panicker, Rajesh C.; Puthusserypady, Sadasivan; Sun, Ying

2011-01-01

In this paper, an asynchronous brain–computer interface (BCI) system combining the P300 and steady-state visually evoked potentials (SSVEPs) paradigms is proposed. The information transfer is accomplished using P300 event-related potential paradigm and the control state (CS) detection is achieved...

A Scalable Multicore Architecture With Heterogeneous Memory Structures for Dynamic Neuromorphic Asynchronous Processors (DYNAPs).

Science.gov (United States)

Moradi, Saber; Qiao, Ning; Stefanini, Fabio; Indiveri, Giacomo

2018-02-01

Neuromorphic computing systems comprise networks of neurons that use asynchronous events for both computation and communication. This type of representation offers several advantages in terms of bandwidth and power consumption in neuromorphic electronic systems. However, managing the traffic of asynchronous events in large scale systems is a daunting task, both in terms of circuit complexity and memory requirements. Here, we present a novel routing methodology that employs both hierarchical and mesh routing strategies and combines heterogeneous memory structures for minimizing both memory requirements and latency, while maximizing programming flexibility to support a wide range of event-based neural network architectures, through parameter configuration. We validated the proposed scheme in a prototype multicore neuromorphic processor chip that employs hybrid analog/digital circuits for emulating synapse and neuron dynamics together with asynchronous digital circuits for managing the address-event traffic. We present a theoretical analysis of the proposed connectivity scheme, describe the methods and circuits used to implement such scheme, and characterize the prototype chip. Finally, we demonstrate the use of the neuromorphic processor with a convolutional neural network for the real-time classification of visual symbols being flashed to a dynamic vision sensor (DVS) at high speed.

Study of a centrifugal pump, asynchronous motor and inverter, using ...

African Journals Online (AJOL)

The signals generated by the micro controller have been used to program the parallel port of a computer. By reading the recorded bits of the parallel port in LabVIEW software, the signals from the micro controller have been restored and made available to the simulation model of the three-phase inverter, asynchronous ...

1 Commande multivariable du moteur asynchrone triphasé à cage ...

African Journals Online (AJOL)

AKA BOKO

Correspondance, courriel : rabenarivo.michel@yahoo.fr. Résumé. La commande du moteur asynchrone triphasé à ... synthèse du système à l'aide du logiciel MATLAB. Mots-clés : commande, système multivariable, variation de ... of the system by MATLAB software. Keywords : control, MIMO system, frequency variation, ...

Forced synchronization and asynchronous quenching in a thermo-acoustic system

Science.gov (United States)

Mondal, Sirshendu; Pawar, Samadhan A.; Sujith, Raman

2017-11-01

Forced synchronization, which has been extensively studied in theory and experiments, occurs through two different mechanisms known as phase locking and asynchronous quenching. The latter indicates the suppression of oscillation amplitude. In most practical combustion systems such as gas turbine engines, the main concern is high amplitude pressure oscillations, known as thermo-acoustic instability. Thermo-acoustic instability is undesirable and needs to be suppressed because of its damaging consequences to an engine. In the present study, a systematic experimental investigation of forced synchronization is performed in a prototypical thermo-acoustic system, a Rijke tube, in its limit cycle operation. Further, we show a qualitatively similar behavior using a reduced order model. In the phase locking region, the simultaneous occurrence of synchronization and resonant amplification leads to high amplitude pressure oscillations. However, a reduction in the amplitude of natural oscillations by about 78% of the unforced amplitude is observed when the forcing frequency is far lower than the natural frequency. This shows the possibility of suppression of the oscillation amplitude through asynchronous quenching in thermo-acoustic systems.

Traffic Multiresolution Modeling and Consistency Analysis of Urban Expressway Based on Asynchronous Integration Strategy

Directory of Open Access Journals (Sweden)

Liyan Zhang

2017-01-01

Full Text Available The paper studies multiresolution traffic flow simulation model of urban expressway. Firstly, compared with two-level hybrid model, three-level multiresolution hybrid model has been chosen. Then, multiresolution simulation framework and integration strategies are introduced. Thirdly, the paper proposes an urban expressway multiresolution traffic simulation model by asynchronous integration strategy based on Set Theory, which includes three submodels: macromodel, mesomodel, and micromodel. After that, the applicable conditions and derivation process of the three submodels are discussed in detail. In addition, in order to simulate and evaluate the multiresolution model, “simple simulation scenario” of North-South Elevated Expressway in Shanghai has been established. The simulation results showed the following. (1 Volume-density relationships of three submodels are unanimous with detector data. (2 When traffic density is high, macromodel has a high precision and smaller error and the dispersion of results is smaller. Compared with macromodel, simulation accuracies of micromodel and mesomodel are lower but errors are bigger. (3 Multiresolution model can simulate characteristics of traffic flow, capture traffic wave, and keep the consistency of traffic state transition. Finally, the results showed that the novel multiresolution model can have higher simulation accuracy and it is feasible and effective in the real traffic simulation scenario.

Experimental analysis of flow structure in contra-rotating axial flow pump designed with different rotational speed concept

Science.gov (United States)

Cao, Linlin; Watanabe, Satoshi; Imanishi, Toshiki; Yoshimura, Hiroaki; Furukawa, Akinori

2013-08-01

As a high specific speed pump, the contra-rotating axial flow pump distinguishes itself in a rear rotor rotating in the opposite direction of the front rotor, which remarkably contributes to the energy conversion, the reduction of the pump size, better hydraulic and cavitation performances. However, with two rotors rotating reversely, the significant interaction between blade rows was observed in our prototype contra-rotating rotors, which highly affected the pump performance compared with the conventional axial flow pumps. Consequently, a new type of rear rotor was designed by the rotational speed optimization methodology with some additional considerations, aiming at better cavitation performance, the reduction of blade rows interaction and the secondary flow suppression. The new rear rotor showed a satisfactory performance at the design flow rate but an unfavorable positive slope of the head — flow rate curve in the partial flow rate range less than 40% of the design flow rate, which should be avoided for the reliability of pump-pipe systems. In the present research, to understand the internal flow field of new rear rotor and its relation to the performances at the partial flow rates, the velocity distributions at the inlets and outlets of the rotors are firstly investigated. Then, the boundary layer flows on rotor surfaces, which clearly reflect the secondary flow inside the rotors, are analyzed through the limiting streamline observations using the multi-color oil-film method. Finally, the unsteady numerical simulations are carried out to understand the complicated internal flow structures in the rotors.

A new asynchronous parallel algorithm for inferring large-scale gene regulatory networks.

Directory of Open Access Journals (Sweden)

Xiangyun Xiao

Full Text Available The reconstruction of gene regulatory networks (GRNs from high-throughput experimental data has been considered one of the most important issues in systems biology research. With the development of high-throughput technology and the complexity of biological problems, we need to reconstruct GRNs that contain thousands of genes. However, when many existing algorithms are used to handle these large-scale problems, they will encounter two important issues: low accuracy and high computational cost. To overcome these difficulties, the main goal of this study is to design an effective parallel algorithm to infer large-scale GRNs based on high-performance parallel computing environments. In this study, we proposed a novel asynchronous parallel framework to improve the accuracy and lower the time complexity of large-scale GRN inference by combining splitting technology and ordinary differential equation (ODE-based optimization. The presented algorithm uses the sparsity and modularity of GRNs to split whole large-scale GRNs into many small-scale modular subnetworks. Through the ODE-based optimization of all subnetworks in parallel and their asynchronous communications, we can easily obtain the parameters of the whole network. To test the performance of the proposed approach, we used well-known benchmark datasets from Dialogue for Reverse Engineering Assessments and Methods challenge (DREAM, experimentally determined GRN of Escherichia coli and one published dataset that contains more than 10 thousand genes to compare the proposed approach with several popular algorithms on the same high-performance computing environments in terms of both accuracy and time complexity. The numerical results demonstrate that our parallel algorithm exhibits obvious superiority in inferring large-scale GRNs.

A new asynchronous parallel algorithm for inferring large-scale gene regulatory networks.

Science.gov (United States)

Xiao, Xiangyun; Zhang, Wei; Zou, Xiufen

2015-01-01

The reconstruction of gene regulatory networks (GRNs) from high-throughput experimental data has been considered one of the most important issues in systems biology research. With the development of high-throughput technology and the complexity of biological problems, we need to reconstruct GRNs that contain thousands of genes. However, when many existing algorithms are used to handle these large-scale problems, they will encounter two important issues: low accuracy and high computational cost. To overcome these difficulties, the main goal of this study is to design an effective parallel algorithm to infer large-scale GRNs based on high-performance parallel computing environments. In this study, we proposed a novel asynchronous parallel framework to improve the accuracy and lower the time complexity of large-scale GRN inference by combining splitting technology and ordinary differential equation (ODE)-based optimization. The presented algorithm uses the sparsity and modularity of GRNs to split whole large-scale GRNs into many small-scale modular subnetworks. Through the ODE-based optimization of all subnetworks in parallel and their asynchronous communications, we can easily obtain the parameters of the whole network. To test the performance of the proposed approach, we used well-known benchmark datasets from Dialogue for Reverse Engineering Assessments and Methods challenge (DREAM), experimentally determined GRN of Escherichia coli and one published dataset that contains more than 10 thousand genes to compare the proposed approach with several popular algorithms on the same high-performance computing environments in terms of both accuracy and time complexity. The numerical results demonstrate that our parallel algorithm exhibits obvious superiority in inferring large-scale GRNs.

Isolation of TRPV1 independent mechanisms of spontaneous and asynchronous glutamate release at primary afferent to NTS synapses.

Directory of Open Access Journals (Sweden)

Axel J. Fenwick

2014-01-01

Full Text Available Cranial visceral afferents contained within the solitary tract (ST contact second-order neurons in the nucleus of the solitary tract (NTS and release the excitatory amino acid glutamate via three distinct exocytosis pathways; synchronous, asynchronous, and spontaneous release. The presence of TRPV1 in the central terminals of a majority of ST afferents conveys activity-dependent asynchronous glutamate release and provides a temperature sensitive calcium conductance which largely determines the rate of spontaneous vesicle fusion. TRPV1 is present in unmyelinated C-fiber afferents and these facilitated forms of glutamate release may underlie the relative strength of C-fibers in activating autonomic reflex pathways. However, pharmacological blockade of TRPV1 signaling eliminates only ~50% of the asynchronous profile and attenuates the temperature sensitivity of spontaneous release indicating additional thermosensitive calcium influx pathways may exist which mediate these forms of vesicle release. In the present study we isolate the contribution of TRPV1 independent forms of glutamate release at ST-NTS synapses. We found ST afferent innervation at NTS neurons and synchronous vesicle release from TRPV1 KO mice was not different to control animals; however, only half of TRPV1 KO ST afferents completely lacked asynchronous glutamate release. Further, temperature driven spontaneous rates of vesicle release were not different from 33˚ - 37˚C between control and TRPV1 KO afferents. These findings suggest additional temperature dependent mechanisms controlling asynchronous and thermosensitive spontaneous release at physiological temperatures, possibly mediated by additional thermosensitive TRP channels in primary afferent terminals.

Physics design of fissile mass-flow monitoring system

International Nuclear Information System (INIS)

Mattingly, J.K.; March-Leuba, J.; Valentine, T.E.; Mihalczo, J.T.; Uckan, T.

1997-01-01

The system measures the flow rate and uranium-235 content in liquid or gas streams; it does not penetrate the process piping. A moderated fission neutron source is used to periodicially introduce a burst of thermal neutrons into the fluid stream to induce fission; delayed gamma emissions from the resulting fission fragments are detected by high-efficiency scintillators downstream of the neutron source. The fluid flow rate is measure from the time between initiation of the thermal neutron burst and detection of the fission product gamma emissions, and the U-235 content is inferred from the intensity of the gamma burst detected. Design of the fissile mass flow monitor requires satisfaction of several competing constraints. Efficient operation of the monitor requires that source-induced fission rate and detection efficiency be maximized while the source-induced background rate is simultaneoulsy minimized. Near optical nuclear design of the system was achieved using numerous Monte Carlo calculations and measurements. This paper addresses calculational aspects of the physics design for the system applied to UF 6 gas

Commande adaptive d'une machine asynchrone

Science.gov (United States)

Slama-Belkhodja, I.; de Fornel, B.

1996-06-01

The paper deals with an indirect self-tuning speed control for an induction motor supplied by a chopper-filter-inverter system. Input/Output models are identified with the recursive least squares algorithm and the controller adaptation is based on a pole assignement strategy. Emphasis is put on the evaluation of the parameter identification in order to avoid instabilities because of disturbances or insufficient excitations. This is especially of importance when the adaptive control is carried out in closed loop systems and without additional test signals. Simulation results show the improvement of the dynamic responses and the robustness against load variations or parameters variations (rotor resistance, inertia). Cat article décrit une stratégie de commande adaptive indirecte à Placement de Pôles (PP), appliquée à la commande en vitesse d'une machine asynchrone alimentée par un ensemble hacheur-filtre-onduleur de tension. L'algorithme des Moindres Carrés Récursifs (MCR) est utilisé pour l'identification des modèles de comportement type entrées/sorties. Un intérêt particulier est porté à la mise en oeuvre de cet algorithme et à la discussion de ses résultats, tenant compte des erreurs de modélisation et de la nature peu riche en excitations des entrées du processus. Différents régimes transitoires ont été simulés pour apprécier l'apport de cette association (MCR-PP) : démarrages et inversion des sens de rotation, à vide et en charges, applications d'échelons de couple résistant, variations paramétriques. Les résultats permettent d'illustrer, tant au niveau des performances que de la robustesse, l'apport d'une telle commande adaptive pour des entraînements électriques avec une machine asynchrone.

Asynchronous data change notification between database server and accelerator control systems

International Nuclear Information System (INIS)

Wenge Fu; Seth Nemesure; Morris, J.

2012-01-01

Database data change notification (DCN) is a commonly used feature, it allows to be informed when the data has been changed on the server side by another client. Not all database management systems (DBMS) provide an explicit DCN mechanism. Even for those DBMS's which support DCN (such as Oracle and MS SQL server), some server side and/or client side programming may be required to make the DCN system work. This makes the setup of DCN between database server and interested clients tedious and time consuming. In accelerator control systems, there are many well established software client/server architectures (such as CDEV, EPICS, and ADO) that can be used to implement data reflection servers that transfer data asynchronously to any client using the standard SET/GET API. This paper describes a method for using such a data reflection server to set up asynchronous DCN (ADCN) between a DBMS and clients. This method works well for all DBMS systems which provide database trigger functionality. (authors)

Simulation models of a drive with an asynchronous electric engine for students of electrical engineering faculties

Directory of Open Access Journals (Sweden)

Romanenko N. G.

2017-10-01

Full Text Available the application of virtual laboratories will allow to show different transition processes, as well as to carry out experiments that are very expensive in real electrical machines’ labs, for example, to calculate the energy costs in electric drives. Models of non-regulation asynchronous drive and frequency-regulated asynchronous electric drive are examined in this article. The author has calculated and compared the energy losses of these systems with various types of loads and this lets us to evaluate work processes of many technical devices.

A proposed through-flow inverse method for the design of mixed-flow pumps

Science.gov (United States)

Borges, Joao Eduardo

1991-01-01

A through-flow (hub-to-shroud) truly inverse method is proposed and described. It uses an imposition of mean swirl, i.e., radius times mean tangential velocity, given throughout the meridional section of the turbomachine as an initial design specification. In the present implementation, it is assumed that the fluid is inviscid, incompressible, and irrotational at inlet and that the blades are supposed to have zero thickness. Only blade rows that impart to the fluid a constant work along the space are considered. An application of this procedure to design the rotor of a mixed-flow pump is described in detail. The strategy used to find a suitable mean swirl distribution and the other design inputs is also described. The final blade shape and pressure distributions on the blade surface are presented, showing that it is possible to obtain feasible designs using this technique. Another advantage of this technique is the fact that it does not require large amounts of CPU time.

Application of Artificial Intelligence Techniques for the Control of the Asynchronous Machine

Directory of Open Access Journals (Sweden)

F. Khammar

2016-01-01

Full Text Available The induction machine is experiencing a growing success for two decades by gradually replacing the DC machines and synchronous in many industrial applications. This paper is devoted to the study of advanced methods applied to the command of the asynchronous machine in order to obtain a system of control of high performance. While the criteria for response time, overtaking, and static error can be assured by the techniques of conventional control, the criterion of robustness remains a challenge for researchers. This criterion can be satisfied only by applying advanced techniques of command. After mathematical modeling of the asynchronous machine, it defines the control strategies based on the orientation of the rotor flux. The results of the different simulation tests highlight the properties of robustness of algorithms proposed and suggested to compare the different control strategies.

Asynchronous Sensor fuSion for Improved Safety of air Traffic (ASSIST), Phase I

Data.gov (United States)

National Aeronautics and Space Administration — SSCI proposes to develop, implement and test a collision detection system for unmanned aerial vehicles (UAV), referred to as the Asynchronous Sensor fuSion for...

A test section design to simulate horizontal two-phase air-water flow

International Nuclear Information System (INIS)

Faccini, Jose Luiz H.; Cesar, Silvia B.G.; Coutinho, Jorge A.; Freitas, Sergio Carlos; Addor, Pedro N.

2002-01-01

In this work an air-water two-phase flow horizontal test section assembling at Nuclear Engineering Institute (IEN) is presented. The test section was designed to allow four-phase flow patterns to be simulated: bubble flow, stratified flow, wave flow and slug flow. These flow patterns will be identified by non-conventional ultrasonic techniques which have been developed to meet this particular application. Based on the separated flow and drift-flux models the test section design steps are shown. A description of the test section and its instrumentation and data acquisition system is also provided. (author)

Merging the Forces of Asynchronous Tutoring and Synchronous Conferencing: A Qualitative Study of Arab ESL Academic Writers Using E-Tutoring

Science.gov (United States)

Alqadoumi, Omar Mohamed

2012-01-01

Previous studies in the field of e-tutoring dealt either with asynchronous tutoring or synchronous conferencing as modes for providing e-tutoring services to English learners. This qualitative research study reports the experiences of Arab ESL tutees with both asynchronous tutoring and synchronous conferencing. It also reports the experiences of…

Model for Investigation of Operational Wind Power Plant Regimes with Doubly–Fed Asynchronous Machine in Power System

Directory of Open Access Journals (Sweden)

R. I. Mustafayev

2012-01-01

Full Text Available The paper presents methodology for mathematical modeling of power system (its part when jointly operated with wind power plants (stations that contain asynchronous doubly-fed machines used as generators. The essence and advantage of the methodology is that it allows efficiently to mate equations of doubly-fed asynchronous machines, written in the axes that rotate with the machine rotor speed with the equations of external electric power system, written in synchronously rotating axes.

Flipping the Online Classroom with Web 2.0: The Asynchronous Workshop

Science.gov (United States)

Cummings, Lance

2016-01-01

This article examines how Web 2.0 technologies can be used to "flip" the online classroom by creating asynchronous workshops in social environments where immediacy and social presence can be maximized. Using experience teaching several communication and writing classes in Google Apps (Google+, Google Hangouts, Google Drive, etc.), I…

Reactors: A data-oriented synchronous/asynchronous programming model for distributed applications

DEFF Research Database (Denmark)

Field, John; Marinescu, Maria-Cristina; Stefansen, Christian Oskar Erik

2009-01-01

of messages. Similarly, the interface to a reactor is simply its state, rather than a collection of message channels, ports, or methods. One novel feature of our model is the ability to compose behaviors both synchronously and asynchronously. Also, our use of Datalog-style rules allows aspect-like composition...

Defining the Symmetry of the Universal Semi-Regular Autonomous Asynchronous Systems

Directory of Open Access Journals (Sweden)

Serban E. Vlad

2012-02-01

Full Text Available The regular autonomous asynchronous systems are the non-deterministic Boolean dynamical systems and universality means the greatest in the sense of the inclusion. The paper gives four definitions of symmetry of these systems in a slightly more general framework, called semi-regularity, and also many examples.

Determining sociability, social space, and social presence in (a)synchronous collaborating groups

NARCIS (Netherlands)

Kreijns, C.J.; Kirschner, P.A.; Jochems, W.M.G.; Buuren, van H.

2004-01-01

The effectiveness of group learning in asynchronous distributed learning groups depends on the social interaction that takes place. This social interaction affects both cognitive and socioemotional processes that take place during learning, group forming, establishment of group structures, and group

Determining sociability, social space, and social presence in (A)synchronous collaborative groups

NARCIS (Netherlands)

Kreijns, K.; Kirschner, P.A.; Jochems, W.; Buuren, H. van

2004-01-01

The effectiveness of group learning in asynchronous distributed learning groups depends on the social interaction that takes place. This social interaction affects both cognitive and socioemotional processes that take place during learning, group forming, establishment of group structures, and group

Toward Design, Modelling and Analysis of Dynamic Workflow Reconfigurations - A Process Algebra Perspective

DEFF Research Database (Denmark)

Mazzara, M.; Abouzaid, F.; Dragoni, Nicola

2011-01-01

This paper describes a case study involving the dynamic re- conguration of an oce work ow. We state the requirements on a sys- tem implementing the work ow and its reconguration, and describe the system's design in BPMN. We then use an asynchronous -calculus and Web1 to model the design and to ve......This paper describes a case study involving the dynamic re- conguration of an oce work ow. We state the requirements on a sys- tem implementing the work ow and its reconguration, and describe the system's design in BPMN. We then use an asynchronous -calculus and Web1 to model the design...

3:1 compression to ventilation ratio versus continuous chest compression with asynchronous ventilation in a porcine model of neonatal resuscitation.

Science.gov (United States)

Schmölzer, Georg M; O'Reilly, Megan; Labossiere, Joseph; Lee, Tze-Fun; Cowan, Shaun; Nicoll, Jessica; Bigam, David L; Cheung, Po-Yin

2014-02-01

In contrast to the resuscitation guidelines of children and adults, guidelines on neonatal resuscitation recommend synchronized 90 chest compressions with 30 manual inflations (3:1) per minute in newborn infants. The study aimed to determine if chest compression with asynchronous ventilation improves the recovery of bradycardic asphyxiated newborn piglets compared to 3:1 Compression:Ventilation cardiopulmonary resuscitation (CPR). Term newborn piglets (n=8/group) were anesthetized, intubated, instrumented and exposed to 45-min normocapnic hypoxia followed by asphyxia. Protocolized resuscitation was initiated when heart rate decreased to 25% of baseline. Piglets were randomized to receive resuscitation with either 3:1 compressions to ventilations (3:1C:V CPR group) or chest compressions with asynchronous ventilations (CCaV) or sham. Continuous respiratory parameters (Respironics NM3(®)), cardiac output, mean systemic and pulmonary artery pressures, and regional blood flows were measured. Piglets in 3:1C:V CPR and CCaV CPR groups had similar time to return of spontaneous circulation, survival rates, hemodynamic and respiratory parameters during CPR. The systemic and regional hemodynamic recovery in the subsequent 4h was similar in both groups and significantly lower compared to sham-operated piglets. Newborn piglets resuscitated by CCaV had similar return of spontaneous circulation, survival, and hemodynamic recovery compared to those piglets resuscitated by 3:1 Compression:Ventilation ratio. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Collaborative design in education : evaluation of three approaches

NARCIS (Netherlands)

Leeuwen, van J.P.; Gassel, van F.J.M.; Otter, den A.F.H.J.; Duarte, J.P.; Sampaio, A.Z.

2005-01-01

Collaboration in design can take place in a physical, social space, in a distributed or virtual environment, or in a combination of both. Design teams use a range of ICT means to support both synchronous and asynchronous communication. While these tools are designed to facilitate collaboration, the

Computer Learner Corpora: Analysing Interlanguage Errors in Synchronous and Asynchronous Communication

Science.gov (United States)

MacDonald, Penny; Garcia-Carbonell, Amparo; Carot, Sierra, Jose Miguel

2013-01-01

This study focuses on the computer-aided analysis of interlanguage errors made by the participants in the telematic simulation IDEELS (Intercultural Dynamics in European Education through on-Line Simulation). The synchronous and asynchronous communication analysed was part of the MiLC Corpus, a multilingual learner corpus of texts written by…

Simulation of the Dynamic Behavior of an Asynchronous Machine Using Direct Self-Control

Directory of Open Access Journals (Sweden)

Cristian Paul Chioncel

2007-01-01

Full Text Available The paper presents the major steps that have to be gone for the implementation of the mathematical model of the asynchronous machine in SciLab / Scicos. This implemented ASM model, will be used to check the dynamic behavior of the system, the current diagrams as well as the behavior motor speed and the torque, if the input signal has a pulsation form. This implementation’s are made in Scilab / Scicos environment, a clone of the MATLAB, which provides number-crunching power similar to MATLAB, at a much better cost/performance ratio. The implemented model offers the possibility to analyze the behaviors of the asynchronous machine in different dynamic situations: speed, torques, current in motor or generator regime and to study its behavior in different possible control schemes.

Asynchronous Gossip-Based Gradient-Free Method for Multiagent Optimization

OpenAIRE

Deming Yuan

2014-01-01

This paper considers the constrained multiagent optimization problem. The objective function of the problem is a sum of convex functions, each of which is known by a specific agent only. For solving this problem, we propose an asynchronous distributed method that is based on gradient-free oracles and gossip algorithm. In contrast to the existing work, we do not require that agents be capable of computing the subgradients of their objective functions and coordinating their...

Synaptotagmin-7 is an asynchronous calcium sensor for synaptic transmission in neurons expressing SNAP-23.

Directory of Open Access Journals (Sweden)

Jens P Weber

Full Text Available Synchronization of neurotransmitter release with the presynaptic action potential is essential for maintaining fidelity of information transfer in the central nervous system. However, synchronous release is frequently accompanied by an asynchronous release component that builds up during repetitive stimulation, and can even play a dominant role in some synapses. Here, we show that substitution of SNAP-23 for SNAP-25 in mouse autaptic glutamatergic hippocampal neurons results in asynchronous release and a higher frequency of spontaneous release events (mEPSCs. Use of neurons from double-knock-out (SNAP-25, synaptotagmin-7 mice in combination with viral transduction showed that SNAP-23-driven release is triggered by endogenous synaptotagmin-7. In the absence of synaptotagmin-7 release became even more asynchronous, and the spontaneous release rate increased even more, indicating that synaptotagmin-7 acts to synchronize release and suppress spontaneous release. However, compared to synaptotagmin-1, synaptotagmin-7 is a both leaky and asynchronous calcium sensor. In the presence of SNAP-25, consequences of the elimination of synaptotagmin-7 were small or absent, indicating that the protein pairs SNAP-25/synaptotagmin-1 and SNAP-23/synaptotagmin-7 might act as mutually exclusive calcium sensors. Expression of fusion proteins between pHluorin (pH-sensitive GFP and synaptotagmin-1 or -7 showed that vesicles that fuse using the SNAP-23/synaptotagmin-7 combination contained synaptotagmin-1, while synaptotagmin-7 barely displayed activity-dependent trafficking between vesicle and plasma membrane, implying that it acts as a plasma membrane calcium sensor. Overall, these findings support the idea of alternative syt∶SNARE combinations driving release with different kinetics and fidelity.

On the design of high-speed energy-efficient successive-approximation logic for asynchronous SAR ADCs

Science.gov (United States)

Yang, Jiaqi; Li, Ting; Yu, Mingyuan; Zhang, Shuangshuang; Lin, Fujiang; He, Lin

2017-08-01

This paper analyzes the power consumption and delay mechanisms of the successive-approximation (SA) logic of a typical asynchronous SAR ADC, and provides strategies to reduce both of them. Following these strategies, a unique direct-pass SA logic is proposed based on a full-swing once-triggered DFF and a self-locking tri-state gate. The unnecessary internal switching power of a typical TSPC DFF, which is commonly used in the SA logic, is avoided. The delay of the ready detector as well as the sequencer is removed from the critical path. A prototype SAR ADC based on the proposed SA logic is fabricated in 130 nm CMOS. It achieves a peak SNDR of 56.3 dB at 1.2 V supply and 65 MS/s sampling rate, and has a total power consumption of 555 μW, while the digital part consumes only 203 μW. Project supported by the National Natural Science Foundation of China (Nos. 61204033, 61331015), the Fundamental Research Funds for the Central Universities (No. WK2100230015), and the Funds of Science and Technology on Analog Integrated Circuit Laboratory (No. 9140C090111150C09041).

An asynchronous, pipelined, electronic acquisition system for Active Matrix Flat-Panel Imagers (AMFPIs)

Energy Technology Data Exchange (ETDEWEB)

Huang, W.; Antonuk, L.E. E-mail: antonuk@umich.edu; Berry, J.; Maolinbay, M.; Martelli, C.; Mody, P.; Nassif, S.; Yeakey, M

1999-07-11

The development of a full-custom electronic acquisition system designed for readout of large-area active matrix flat-panel imaging arrays is reported. The arrays, which comprise two-dimensional matrices of pixels utilizing amorphous silicon thin-film transistors, are themselves under development for a wide variety of X-ray imaging applications. The acquisition system was specifically designed to facilitate detailed, quantitative investigations of the properties of these novel imaging arrays and contains significant enhancements compared to a previously developed acquisition system. These enhancements include pipelined preamplifier circuits to allow faster readout speed, expanded addressing capabilities allowing a maximum of 4096 array data lines, and on-board summing of image frames. The values of many acquisition system parameters, including timings and voltages, may be specified and downloaded from a host computer. Once acquisition is enabled, the system operates asynchronously of its host computer. The system allows image capture in both radiographic mode (corresponding to the capture of individual X-ray images), and fluoroscopic mode (corresponding to the capture of a continual series of X-ray images). A detailed description of the system architecture and the underlying motivations for the design is reported in this paper. (author)

Design of a collector shape for uniform flow distribution in microchannels

International Nuclear Information System (INIS)

Siddique, Ayyaz; Agrawal, Amit; Saha, Sandip K; Medhi, Bhaskar J; Singh, Anugrah

2017-01-01

The focus of this study is the design of a collector with the objective of achieving uniform flow in multiple parallel microchannels. This objective is achieved by understanding the limitations of current designs and a novel design is proposed, which is further carefully optimized. The existing collector shape considered is U-type, which is investigated numerically. The creation of a stagnation zone, growth of a boundary layer along the collector wall and low/high velocity zones in the collector are identified as the prime causes of flow maldistribution. A novel design, a dumbbell shape collector, is proposed to overcome the limitations of the earlier designs. The dumbbell shape is evaluated quantitatively and is found to perform better than all existing shapes. This dumbbell shape collector provides a uniform flow distribution with less than 0.4% relative difference from the average flow rate in different channels, which is substantially better than existing collectors with 2.3% relative difference from the average flow rate for Re ch   =  32. The uniformity is further confirmed using micro-particle image velocimetry measurements. The dumbbell shape collector is generalized and optimized to cater to heat sinks of different dimensions and to broaden its applicability in both micro and macro dimensions. (paper)

Asynchronous Task-Based Polar Decomposition on Manycore Architectures

KAUST Repository

Sukkari, Dalal

2016-10-25

This paper introduces the first asynchronous, task-based implementation of the polar decomposition on manycore architectures. Based on a new formulation of the iterative QR dynamically-weighted Halley algorithm (QDWH) for the calculation of the polar decomposition, the proposed implementation replaces the original and hostile LU factorization for the condition number estimator by the more adequate QR factorization to enable software portability across various architectures. Relying on fine-grained computations, the novel task-based implementation is also capable of taking advantage of the identity structure of the matrix involved during the QDWH iterations, which decreases the overall algorithmic complexity. Furthermore, the artifactual synchronization points have been severely weakened compared to previous implementations, unveiling look-ahead opportunities for better hardware occupancy. The overall QDWH-based polar decomposition can then be represented as a directed acyclic graph (DAG), where nodes represent computational tasks and edges define the inter-task data dependencies. The StarPU dynamic runtime system is employed to traverse the DAG, to track the various data dependencies and to asynchronously schedule the computational tasks on the underlying hardware resources, resulting in an out-of-order task scheduling. Benchmarking experiments show significant improvements against existing state-of-the-art high performance implementations (i.e., Intel MKL and Elemental) for the polar decomposition on latest shared-memory vendors\\' systems (i.e., Intel Haswell/Broadwell/Knights Landing, NVIDIA K80/P100 GPUs and IBM Power8), while maintaining high numerical accuracy.

Scalable design of an IMS cross-flow micro-generator/ion detector

International Nuclear Information System (INIS)

Ortiz, Juan J; Nigri, Christian; Lasorsa, Carlos; Ortiz, Guillermo P

2013-01-01

Ion-mobility spectrometry (IMS) is an analytical technique used to separate and identify ionized gas molecules based on their mobility in a carrier buffer gas. Such methods come in a large variety of versions that currently allow ion identification at and above the millimeter scale. Here, we present a design for a cross-flow IMS method able to generate and detect ions at the sub-millimeter scale. We propose a novel ion focusing strategy and test it in a prototype device using nitrogen as a sample gas, and also with simulations using four different sample gases. By introducing an original lobular ion generation localized to a few ten of microns and substantially simplifying the design, our device is able to keep constant laminar flow conditions for high flow rates. In this way, it avoids the turbulences in the gas flow, which would occur in other ion-focusing cross-flow methods limiting their performance at the sub-millimeter scale. Scalability of the proposed design can contribute to improve the resolving power and resolution of currently available cross-flow methods. (paper)

Design Tools for Integrated Asynchronous Electronic Circuits

National Research Council Canada - National Science Library

Martin, Alain

2003-01-01

..., simulation, verification, at the logical and physical levels. Situs has developed a business model for the commercialization of the CAD tools, and has designed the prototype of the tool suite based on this business model and the Caltech approach...

Simulation of an Asynchronous Machine by using a Pseudo Bond Graph

Science.gov (United States)

Romero, Gregorio; Felez, Jesus; Maroto, Joaquin; Martinez, M. Luisa

2008-11-01

For engineers, computer simulation, is a basic tool since it enables them to understand how systems work without actually needing to see them. They can learn how they work in different circumstances and optimize their design with considerably less cost in terms of time and money than if they had to carry out tests on a physical system. However, if computer simulation is to be reliable it is essential for the simulation model to be validated. There is a wide range of commercial brands on the market offering products for electrical domain simulation (SPICE, LabVIEW PSCAD,Dymola, Simulink, Simplorer,...). These are powerful tools, but require the engineer to have a perfect knowledge of the electrical field. This paper shows an alternative methodology to can simulate an asynchronous machine using the multidomain Bond Graph technique and apply it in any program that permit the simulation of models based in this technique; no extraordinary knowledge of this technique and electric field are required to understand the process .

Advancements in flow-induced vibration research and design criteria

International Nuclear Information System (INIS)

Pettigrew, M.J.

2009-01-01

Two-phase flow exists in many nuclear components and, in particular, steam generators. So far relatively little research work has been done on two-phase flow-induced vibration probably because it is difficult to do. Two-phase flows are not homogeneous and are governed by an additional parameter called void fraction. This can lead to different flow patterns or regimes that can change completely the vibration behaviour. Fluidelastic instability, random turbulence excitation and detailed flow characteristics are being investigated in tube bundles subjected to two-phase cross flow. Fluidelastic instability of a tube bundle preferentially flexible in the flow direction was observed probably for the first time. This is particularly relevant to the problem of in-plane vibration of nuclear steam generator U-tubes and has resulted in changes in our design criteria. Unexpected quasi-periodic excitation forces were also measured in the tube bundle. These are attributed to an alternating wake in the lift direction and to fluctuating momentum flux in the drag direction. Vibration damping due to two-phase flow is very dependent on void fraction and appears directly related to the interface surface area between phases. Maximum damping values correspond to the transitions between flow regimes. Fibre optic probes were developed to measure the characteristics of two-phase flows. These probes are used to take detailed measurements in a triangular array of tubes in cross flow. The results show that the flow tends to stream between the tubes. These studies have yielded interesting results but have raised more questions that could lead to improved design criteria. The more puzzling results will be discussed in this presentation. Some of the dynamic phenomena will be illustrated by animation. (author)

Design of the Flow Plates for a Dual Cooled Fuel Assembly

International Nuclear Information System (INIS)

Kim, Jae Yong; Yoon, Kyung Ho; Lee, Young Ho; Lee, Kang Hee; Kim, Hyung Kyu

2009-01-01

In a dual cooled fuel assembly, the array and position of fuels are changed from those of a conventional PWR fuel assembly to achieve a power uprating. The flow plate provides flow holes to direct the heated coolant into/out of the fuel assembly and structural intensity to insure that the fuel rod is axially restrained within the spacer grids. So, flow plates of top/bottom end pieces (TEP/BEP) have to be modified into proper shape. Because the flow holes' area of a flow plate affects pressure drop, the flow holes' area must be larger than/equal to that of conventional flow plates. And design criterion of the TEP/BEP says that the flow plate should withstand a 22.241 kN axial load during handling lest a calculated stress intensity should exceed the Condition I allowable stress. In this paper, newly designed flow plates of a TEP/BEP are suggested and stress analysis is conducted to evaluate strength robustness of the flow plates for the dual cooled fuel assembly

Beyond Social Presence: Facelessness and the Ethics of Asynchronous Online Education

Science.gov (United States)

Rose, Ellen

2017-01-01

In this position paper, I argue that a focus on achieving and increasing social presence in online courses tends to derail a consideration of the ethical implications and dimensions of the essential facelessness of asynchronous education. Drawing upon the work of Emmanuel Levinas and Nel Noddings, who contended that the face is the basis of…

Asynchronous monitoring of the quality of multilevel optical PAM signals

Science.gov (United States)

Siuzdak, J.

2017-08-01

In the paper, there is analyzed the signal quality assessment method based on delay tap asynchronous sampling, both for binary and multilevel PAM signals. The obtained multilevel phase diagrams are far more complicated than binary ones. The phase diagrams are affected by the signal distortions but it is difficult to relate reliably the phase diagram form to the distortion type and its influence on the signal quality.

Computer-Aided Test Flow in Core-Based Design

NARCIS (Netherlands)

Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

2000-01-01

This paper copes with the test-pattern generation and fault coverage determination in the core based design. The basic core-test strategy that one has to apply in the core-based design is stated in this work. A Computer-Aided Test (CAT) flow is proposed resulting in accurate fault coverage of

Asynchronous data-driven classification of weapon systems

International Nuclear Information System (INIS)

Jin, Xin; Mukherjee, Kushal; Gupta, Shalabh; Ray, Asok; Phoha, Shashi; Damarla, Thyagaraju

2009-01-01

This communication addresses real-time weapon classification by analysis of asynchronous acoustic data, collected from microphones on a sensor network. The weapon classification algorithm consists of two parts: (i) feature extraction from time-series data using symbolic dynamic filtering (SDF), and (ii) pattern classification based on the extracted features using the language measure (LM) and support vector machine (SVM). The proposed algorithm has been tested on field data, generated by firing of two types of rifles. The results of analysis demonstrate high accuracy and fast execution of the pattern classification algorithm with low memory requirements. Potential applications include simultaneous shooter localization and weapon classification with soldier-wearable networked sensors. (rapid communication)

From discrete-time models to continuous-time, asynchronous modeling of financial markets

NARCIS (Netherlands)

Boer, Katalin; Kaymak, Uzay; Spiering, Jaap

2007-01-01

Most agent-based simulation models of financial markets are discrete-time in nature. In this paper, we investigate to what degree such models are extensible to continuous-time, asynchronous modeling of financial markets. We study the behavior of a learning market maker in a market with information

From Discrete-Time Models to Continuous-Time, Asynchronous Models of Financial Markets

NARCIS (Netherlands)

K. Boer-Sorban (Katalin); U. Kaymak (Uzay); J. Spiering (Jaap)

2006-01-01

textabstractMost agent-based simulation models of financial markets are discrete-time in nature. In this paper, we investigate to what degree such models are extensible to continuous-time, asynchronous modelling of financial markets. We study the behaviour of a learning market maker in a market with

Cultural Influences on Chinese Students' Asynchronous Online Learning in a Canadian University

Science.gov (United States)

Zhao, Naxin; McDougall, Douglas

2008-01-01

This study explored six Chinese graduate students' asynchronous online learning in a large urban Canadian university. Individual interviews in Mandarin elicited their perceptions of online learning, their participation in it, and the cultural factors that influenced their experiences. In general, the participants had a positive attitude towards…

FLUKA Studies of the Asynchronous Beam Dump Effects on LHC Point 6

CERN Document Server

Versaci, R; Goddard, B; Schmidt, R; Vlachoudis, V; Mereghetti, A

2011-01-01

The LHC is a record-breaking machine for beam energy and intensity. An intense effort has therefore been deployed in simulating critical operational scenarios of energy deposition. FLUKA is the most widely used code for this kind of simulations at CERN because of the high reliability of its results and the ease to custom detailed simulations all along hundreds of meters of beam line. We have investigated the effects of an asynchronous beam dump on the LHC Point 6 where, beams with a stored energy of 360 MJ, can instantaneously release up to a few J cm−3 in the cryogenic magnets which have a quench limit of the order of the mJ cm−3. In the present paper we will describe the simulation approach, and discuss the evaluated maximum energy release onto the superconducting magnets during an asynchronous beam dump. We will then analyse the shielding provided by collimators installed in the area and discuss safety limits for the operation of the LHC.

Accelerator physics studies on the effects from an asynchronous beam dump onto the LHC experimental region collimators

CERN Document Server

Lari, L; Boccone, V; Bruce, R; Cerutti, F; Rossi, A; Vlachoudis, V; Mereghetti, A; Faus-Golfe, A

2012-01-01

Asynchronous beam aborts at the LHC are estimated to occur on average once per year. Accelerator physics studies of asynchronous dumps have been performed at different beam energies and beta-stars. The loss patterns are analyzed in order to identify the losses in particular on the Phase 1 Tertiary Collimators (TCT), since their tungsten-based active jaw insert has a lower damage threshold than the carbon-based other LHC collimators. Settings of the tilt angle of the TCTs are discussed with the aim of reducing the thermal loads on the TCT themselves.

Transition to Asynchronous Transfer Mode (ATM) an Implementation Model for NPS Software Metrics Lab

National Research Council Canada - National Science Library

Carney, Cameron

1999-01-01

With Asynchronous Transfer Mode (ATM), we are experiencing the emergence of a network technology that has the potential of satisfying the requirement for a worldwide standard to allow interoperability of information, regardless...

Investigation of a photo-voltaic pump station with asynchronous electric drive

International Nuclear Information System (INIS)

Dzhagarov, N.; Vladimirov, P.

2000-01-01

A scheme of a photo-voltaic pump station with constant current drive is presented. The requirements for reliability and minimal maintenance necessitate the use of asynchronous drive which has been studied. The studies of the system's model for various regimes show its adequacy. The model can be used for determination of the optimal conditions providing maximal working efficiency

Information Flow Through Stages of Complex Engineering Design Projects: A Dynamic Network Analysis Approach

DEFF Research Database (Denmark)

Parraguez, Pedro; Eppinger, Steven D.; Maier, Anja

2015-01-01

The pattern of information flow through the network of interdependent design activities is thought to be an important determinant of engineering design process results. A previously unexplored aspect of such patterns relates to the temporal dynamics of information transfer between activities...... design process and thus support theory-building toward the evolution of information flows through systems engineering stages. Implications include guidance on how to analyze and predict information flows as well as better planning of information flows in engineering design projects according...

Synchronous and Asynchronous Communication in Distance Learning: A Review of the Literature

Science.gov (United States)

Watts, Lynette

2016-01-01

Distance learning is commonplace in higher education, with increasing numbers of students enjoying the flexibility e-learning provides. Keeping students connected with peers and instructors has been a challenge with e-learning, but as technology has advanced, the methods by which educators keep students engaged, synchronously and asynchronously,…

Modelling of hot air chamber designs of a continuous flow grain dryer

DEFF Research Database (Denmark)

Kjær, Lotte Strange; Poulsen, Mathias; Sørensen, Kim

2018-01-01

The pressure loss, flow distribution and temperature distribution of a number of designs of the hot air chamber in a continuous flow grain dryer, were investigated using CFD. The flow in the dryer was considered as steady state, compressible and turbulent. It is essential that the grain...... is uniformly dried as uneven drying can result in damage to the end-product during storage. The original commercial design was modified with new guide vanes at the inlets to reduce the pressure loss and to ensure a uniform flow to the line burner in the hot air chamber. The new guide vane design resulted...... in a 10% reduction in pressure loss and a γ-value of 0.804. Various design changes of the hot air chamber were analysed in terms of pressure loss and temperature distribution with the aim of a temperature variation of 5 K at the outlet ducts. An obstruction design was analysed, which improved mixing...

Synchronization, retiming and OTDM of an asynchronous 10 Gigabit Ethernet NRZ packet using a time lens for Terabit Ethernet

DEFF Research Database (Denmark)

Hu, Hao; Laguardia Areal, Janaina; Mulvad, Hans Christian Hansen

2011-01-01

An asynchronous 10G Ethernet packet is synchronized and retimed to a master clock using a time lens. The NRZ packet is converted into an RZ packet and multiplexed with a serial 1.28 Tb/s signal.......An asynchronous 10G Ethernet packet is synchronized and retimed to a master clock using a time lens. The NRZ packet is converted into an RZ packet and multiplexed with a serial 1.28 Tb/s signal....

General-purpose stepping motor-encoder positioning subsystem with standard asynchronous serial-line interface

International Nuclear Information System (INIS)

Stubblefield, F.W.; Alberi, J.L.

1982-01-01

A general-purpose mechanical positioning subsystem for open-loop control of experiment devices which have their positions established and read out by stepping motor-encoder combinations has been developed. The subsystem is to be used mainly for experiments to be conducted at the National Synchrotron Light Source at Brookhaven National Laboratory. The subsystem unit has been designed to be compatible with a wide variety of stepping motor and encoder types. The unit may be operated by any device capable of driving a standard RS-232-C asynchronous serial communication line. An informal survey has shown that several experiments at the Light Source will use one particular type of computer, operating system, and programming language. Accordingly, a library of subroutines compatible with this combination of computer system elements has been written to facilitate driving the positioning subsystem unit

Evolution of asynchronous motor activity in paired muscles: effects of ecology, morphology, and phylogeny.

Science.gov (United States)

Gerry, Shannon P; Ramsay, Jason B; Dean, Mason N; Wilga, Cheryl D

2008-08-01

Many studies of feeding behavior have implanted electrodes unilaterally (in muscles on only one side of the head) to determine the basic motor patterns of muscles controlling the jaws. However, bilateral implantation has the potential to achieve a more comprehensive understanding of modification of the motor activity that may be occurring between the left and right sides of the head. In particular, complex processing of prey is often characterized by bilaterally asynchronous and even unilateral activation of the jaw musculature. In this study, we bilaterally implant feeding muscles in species from four orders of elasmobranchs (Squaliformes, Orectolobiformes, Carcharhiniformes, Rajoidea) in order to characterize the effects of type of prey, feeding behavior, and phylogeny on the degree of asynchronous muscle activation. Electrodes were implanted in three of the jaw adductors, two divisions of the quadratomandibularis and the preorbitalis, as well as in a cranial elevator in sharks, the epaxialis. The asynchrony of feeding events (measured as the degree to which activity of members of a muscle pair is out of phase) was compared across species for capture versus processing and simple versus complex prey, then interpreted in the contexts of phylogeny, morphology, and ecology to clarify determinants of asynchronous activity. Whereas capture and processing of prey were characterized by statistically similar degrees of asynchrony for data pooled across species, events involving complex prey were more asynchronous than were those involving simple prey. The two trophic generalists, Squalus acanthias and Leucoraja erinacea, modulated the degree of asynchrony according to type of prey, whereas the two behavioral specialists, Chiloscyllium plagiosum and Mustelus canis, activated the cranial muscles synchronously regardless of type of prey. These differences in jaw muscle activity would not have been detected with unilateral implantation. Therefore, we advocate bilateral

Simulation and Analysis of Autonomous Time Synchronization Based on Asynchronism Two-way Inter-satellite Link

Science.gov (United States)

Fang, L.; Yang, X. H.; Sun, B. Q.; Qin, W. J.; Kong, Y.

2013-09-01

The measurement of the inter-satellite link is one of the key techniques in the autonomous operation of satellite navigation system. Based on the asynchronism inter-satellite two-way measurement mode in GPS constellation, the reduction formula of the inter-satellite time synchronization is built in this paper. Moreover, the corrective method of main systematic errors is proposed. Inter-satellite two-way time synchronization is simulated on the basis of IGS (International GNSS Service) precise ephemeris. The impacts of the epoch domestication of asynchronism inter-satellite link pseudo-range, the initial orbit, and the main systematic errors on satellite time synchronization are analyzed. Furthermore, the broadcast clock error of each satellite is calculated by the ``centralized'' inter-satellite autonomous time synchronization. Simulation results show that the epoch domestication of asynchronism inter-satellite link pseudo-range and the initial orbit have little impact on the satellite clock errors, and thus they needn't be taken into account. The errors caused by the relativistic effect and the asymmetry of path travel have large impact on the satellite clock errors. These should be corrected with theoretical formula. Compared with the IGS precise clock error, the root mean square of the broadcast clock error of each satellite is about 0.4 ns.

Asynchronous Execution of the Fast Multipole Method Using Charm++

OpenAIRE

AbdulJabbar, Mustafa; Yokota, Rio; Keyes, David

2014-01-01

Fast multipole methods (FMM) on distributed mem- ory have traditionally used a bulk-synchronous model of com- municating the local essential tree (LET) and overlapping it with computation of the local data. This could be perceived as an extreme case of data aggregation, where the whole LET is communicated at once. Charm++ allows a much finer control over the granularity of communication, and has a asynchronous execution model that fits well with the structure of our FMM code. Unlike previous ...

The use of flow models for design of plant operating procedures

International Nuclear Information System (INIS)

Lind, M.

1982-03-01

The report describe a systematic approach to the design of operating procedures or sequence automatics for process plant control. It is shown how flow models representing the topology of mass and energy flows on different levels of function provide plant information which is important for the considered design problem. The modelling methodology leads to the definition of three categories of control tasks. Two tasks relate to the regulation and control of changes of levels and flows of mass and energy in a system within a defined mode of operation. The third type relate to the control actions necessary for switching operations involved in changes of operating mode. These control tasks are identified for a given plant as part of the flow modelling activity. It is discussed how the flow model deal with the problem of assigning control task precedence in time eg. during start-up or shut-down operations. The method may be a basis for providing automated procedure support to the operator in unforeseen situations or may be a tool for control design. (auth.)

Diagnosis of hearing loss using automated audiometry in an asynchronous telehealth model: A pilot accuracy study.

Science.gov (United States)

Brennan-Jones, Christopher G; Eikelboom, Robert H; Swanepoel, De Wet

2017-02-01

Introduction Standard criteria exist for diagnosing different types of hearing loss, yet audiologists interpret audiograms manually. This pilot study examined the feasibility of standardised interpretations of audiometry in a telehealth model of care. The aim of this study was to examine diagnostic accuracy of automated audiometry in adults with hearing loss in an asynchronous telehealth model using pre-defined diagnostic protocols. Materials and methods We recruited 42 study participants from a public audiology and otolaryngology clinic in Perth, Western Australia. Manual audiometry was performed by an audiologist either before or after automated audiometry. Diagnostic protocols were applied asynchronously for normal hearing, disabling hearing loss, conductive hearing loss and unilateral hearing loss. Sensitivity and specificity analyses were conducted using a two-by-two matrix and Cohen's kappa was used to measure agreement. Results The overall sensitivity for the diagnostic criteria was 0.88 (range: 0.86-1) and overall specificity was 0.93 (range: 0.86-0.97). Overall kappa ( k) agreement was 'substantial' k = 0.80 (95% confidence interval (CI) 0.70-0.89) and significant at p loss. This method has the potential to improve synchronous and asynchronous tele-audiology service delivery.

Model-based design and optimization of vanadium redox flow batteries

Energy Technology Data Exchange (ETDEWEB)

Koenig, Sebastian

2017-07-19

This work targets on increasing the efficiency of the Vanadium Redox Flow Battery (VRFB) using a model-based approach. First, a detailed instruction for setting up a VRFB model on a system level is given. Modelling of open-circuit-voltage, ohmic overpotential, concentration overpotential, Vanadium crossover, shunt currents as well as pump power demand is presented. All sub-models are illustrated using numerical examples. Using experimental data from three battery manufacturers, the voltage model validated. The identified deviations reveal deficiencies in the literature model. By correctly deriving the mass transfer coefficients and adapting the effective electrode area, these deficiencies are eliminated. The validated battery model is then deployed in an extensive design study. By varying the electrode area between 1000 and 4000 cm{sup 2} and varying the design of the electrolyte supply channel, twenty-four different cell designs are created using finite element analysis. These designs are subsequently simulated in 40-cell stacks deployed in systems with a single stack and systems with a three-stack string. Using the simulation results, the impact of different design parameters on different loss mechanisms is investigated. While operating the VRFB, the electrolyte flow rate is the most important operational parameter. A novel, model-based optimization strategy is presented and compared to established flow rate control strategies. Further, a voltage controller is introduced which delays the violation of cell voltage limits by controlling the flow rate as long as the pump capacity is not fully exploited.

Model-based design and optimization of vanadium redox flow batteries

International Nuclear Information System (INIS)

Koenig, Sebastian

2017-01-01

This work targets on increasing the efficiency of the Vanadium Redox Flow Battery (VRFB) using a model-based approach. First, a detailed instruction for setting up a VRFB model on a system level is given. Modelling of open-circuit-voltage, ohmic overpotential, concentration overpotential, Vanadium crossover, shunt currents as well as pump power demand is presented. All sub-models are illustrated using numerical examples. Using experimental data from three battery manufacturers, the voltage model validated. The identified deviations reveal deficiencies in the literature model. By correctly deriving the mass transfer coefficients and adapting the effective electrode area, these deficiencies are eliminated. The validated battery model is then deployed in an extensive design study. By varying the electrode area between 1000 and 4000 cm 2 and varying the design of the electrolyte supply channel, twenty-four different cell designs are created using finite element analysis. These designs are subsequently simulated in 40-cell stacks deployed in systems with a single stack and systems with a three-stack string. Using the simulation results, the impact of different design parameters on different loss mechanisms is investigated. While operating the VRFB, the electrolyte flow rate is the most important operational parameter. A novel, model-based optimization strategy is presented and compared to established flow rate control strategies. Further, a voltage controller is introduced which delays the violation of cell voltage limits by controlling the flow rate as long as the pump capacity is not fully exploited.

Network innovation through OpenFlow and SDN principles and design

CERN Document Server

Hu, Fei

2014-01-01

FUNDAMENTALSSDN /OpenFlow: Concepts and Applications; Ashley Gerrity and Fei HuAn OpenFlow Network Design Cycle; Pedro A. Aranda Gutiřrez and Diego R. LopezDESIGNIP Source Address Validation Solution with OpenFlow Extension and OpenRouter; Jun BiLanguage and Programming in SDN /OpenFlow; Muhammad Farooq and Fei HuControl and Management Software for SDNs; Natalia Castro Fernandes and Luiz Claudio Schara MagalhêsController Architecture and Performance in Software-Defined Networks; Ting Zhang and Fei HuMobile Applications on Global Clouds Using OpenFlow and Software-Defined Networking; Subharth

Learning about the Literacy Development of English Language Learners in Asynchronous Online Discussions

Science.gov (United States)

De Oliveira, Luciana C.; Olesova, Larisa

2013-01-01

This study examined asynchronous online discussions in the online course "English Language Development" to identify themes related to participants' learning about the language and literacy development of English Language Learners when they facilitated online discussions to determine whether the participants developed sufficient…

Design Flow Instantiation for Run-Time Reconfigurable Systems: A Case Study

Directory of Open Access Journals (Sweden)

Yang Qu

2007-12-01

Full Text Available Reconfigurable system is a promising alternative to deliver both flexibility and performance at the same time. New reconfigurable technologies and technology-dependent tools have been developed, but a complete overview of the whole design flow for run-time reconfigurable systems is missing. In this work, we present a design flow instantiation for such systems using a real-life application. The design flow is roughly divided into two parts: system level and implementation. At system level, our supports for hardware resource estimation and performance evaluation are applied. At implementation level, technology-dependent tools are used to realize the run-time reconfiguration. The design case is part of a WCDMA decoder on a commercially available reconfigurable platform. The results show that using run-time reconfiguration can save over 40% area when compared to a functionally equivalent fixed system and achieve 30 times speedup in processing time when compared to a functionally equivalent pure software design.

The effects on health behavior and health outcomes of Internet-based asynchronous communication between health providers and patients with a chronic condition: a systematic review.

Science.gov (United States)

de Jong, Catharina Carolina; Ros, Wynand Jg; Schrijvers, Guus

2014-01-16

In support of professional practice, asynchronous communication between the patient and the provider is implemented separately or in combination with Internet-based self-management interventions. This interaction occurs primarily through electronic messaging or discussion boards. There is little evidence as to whether it is a useful tool for chronically ill patients to support their self-management and increase the effectiveness of interventions. The aim of our study was to review the use and usability of patient-provider asynchronous communication for chronically ill patients and the effects of such communication on health behavior, health outcomes, and patient satisfaction. A literature search was performed using PubMed and Embase. The quality of the articles was appraised according to the National Institute for Health and Clinical Excellence (NICE) criteria. The use and usability of the asynchronous communication was analyzed by examining the frequency of use and the number of users of the interventions with asynchronous communication, as well as of separate electronic messaging. The effectiveness of asynchronous communication was analyzed by examining effects on health behavior, health outcomes, and patient satisfaction. Patients' knowledge concerning their chronic condition increased and they seemed to appreciate being able to communicate asynchronously with their providers. They not only had specific questions but also wanted to communicate about feeling ill. A decrease in visits to the physician was shown in two studies (P=.07, P=.07). Increases in self-management/self-efficacy for patients with back pain, dyspnea, and heart failure were found. Positive health outcomes were shown in 12 studies, where the clinical outcomes for diabetic patients (HbA1c level) and for asthmatic patients (forced expiratory volume [FEV]) improved. Physical symptoms improved in five studies. Five studies generated a variety of positive psychosocial outcomes. The effect of

Asynchronous Task-Based Polar Decomposition on Single Node Manycore Architectures

KAUST Repository

Sukkari, Dalal E.; Ltaief, Hatem; Faverge, Mathieu; Keyes, David E.

2017-01-01

This paper introduces the first asynchronous, task-based formulation of the polar decomposition and its corresponding implementation on manycore architectures. Based on a formulation of the iterative QR dynamically-weighted Halley algorithm (QDWH) for the calculation of the polar decomposition, the proposed implementation replaces the original LU factorization for the condition number estimator by the more adequate QR factorization to enable software portability across various architectures. Relying on fine-grained computations, the novel task-based implementation is capable of taking advantage of the identity structure of the matrix involved during the QDWH iterations, which decreases the overall algorithmic complexity. Furthermore, the artifactual synchronization points have been weakened compared to previous implementations, unveiling look-ahead opportunities for better hardware occupancy. The overall QDWH-based polar decomposition can then be represented as a directed acyclic graph (DAG), where nodes represent computational tasks and edges define the inter-task data dependencies. The StarPU dynamic runtime system is employed to traverse the DAG, to track the various data dependencies and to asynchronously schedule the computational tasks on the underlying hardware resources, resulting in an out-of-order task scheduling. Benchmarking experiments show significant improvements against existing state-of-the-art high performance implementations for the polar decomposition on latest shared-memory vendors' systems, while maintaining numerical accuracy.

Asynchronous Task-Based Polar Decomposition on Single Node Manycore Architectures

KAUST Repository

Sukkari, Dalal E.

2017-09-29

This paper introduces the first asynchronous, task-based formulation of the polar decomposition and its corresponding implementation on manycore architectures. Based on a formulation of the iterative QR dynamically-weighted Halley algorithm (QDWH) for the calculation of the polar decomposition, the proposed implementation replaces the original LU factorization for the condition number estimator by the more adequate QR factorization to enable software portability across various architectures. Relying on fine-grained computations, the novel task-based implementation is capable of taking advantage of the identity structure of the matrix involved during the QDWH iterations, which decreases the overall algorithmic complexity. Furthermore, the artifactual synchronization points have been weakened compared to previous implementations, unveiling look-ahead opportunities for better hardware occupancy. The overall QDWH-based polar decomposition can then be represented as a directed acyclic graph (DAG), where nodes represent computational tasks and edges define the inter-task data dependencies. The StarPU dynamic runtime system is employed to traverse the DAG, to track the various data dependencies and to asynchronously schedule the computational tasks on the underlying hardware resources, resulting in an out-of-order task scheduling. Benchmarking experiments show significant improvements against existing state-of-the-art high performance implementations for the polar decomposition on latest shared-memory vendors\\' systems, while maintaining numerical accuracy.

Modeling and design of optimal flow perfusion bioreactors for tissue engineering applications.

Science.gov (United States)

Hidalgo-Bastida, L Araida; Thirunavukkarasu, Sundaramoorthy; Griffiths, Sarah; Cartmell, Sarah H; Naire, Shailesh

2012-04-01

Perfusion bioreactors have been used in different tissue engineering applications because of their consistent distribution of nutrients and flow-induced shear stress within the tissue-engineering scaffold. A widely used configuration uses a scaffold with a circular cross-section enclosed within a cylindrical chamber and inlet and outlet pipes which are connected to the chamber on either side through which media is continuously circulated. However, fluid-flow experiments and simulations have shown that the majority of the flow perfuses through the center. This pattern creates stagnant zones in the peripheral regions as well as in those of high flow rate near the inlet and outlet. This non-uniformity of flow and shear stress, owing to a circular design, results in limited cell proliferation and differentiation in these areas. The focus of this communication is to design an optimized perfusion system using computational fluid dynamics as a mathematical tool to overcome the time-consuming trial and error experimental method. We compared the flow within a circular and a rectangular bioreactor system. Flow simulations within the rectangular bioreactor are shown to overcome the limitations in the circular design. This communication challenges the circular cross-section bioreactor configuration paradigm and provides proof of the advantages of the new design over the existing one. Copyright © 2011 Wiley Periodicals, Inc.

Study of Mouthguard Design for Endurance and Air-Flow Intake

Science.gov (United States)

Zaman, I.; Rozlan, S. A. M.; Manshoor, B.; Ngali, M. Z.; Khalid, A.; Amin, N. A. M.

2017-08-01

Mouthguard is one of the important device for athletes. Wearing a mouthguard is a must to prevent them from any orofacial injuries occurs during their sport activities. Therefore, to make sure it is safe and comfort, a study on the mouthguard design is carried out to investigate the performance of the mouthguard, in term of stress distribution and air flow path by improving the pressure difference between ambient and the oral cavity pressure. A preliminary design has been study to simulate its total deformation and stress, in terms of Von Mises Stress by using ANSYS 15.0 Workbench. From the results, the critical parts are identified on the preliminary design and later being used to improve the design to the new one. By increasing the thickness of the preliminary design, the total deformation has been decreased for about 0.20 mm to 0.16 mm for the exerted external forces ranging from 50-500 N, whereas, for internal forces ranging from 100-600 N have reduced deformation from 0.24 mm to 1.44 mm. The simulation process is then followed by the air flow study in the oral cavity with an open mouth about 0.5 mm when the athlete is doing exercise with speed 4.43 m/s of air flow into a mouth. The finding indicates that the modified mouthguard has large value of velocity streamline compared to the preliminary design which is supported by significant pressure difference of 401.86 Pa, compared to 140.09 Pa of the preliminary design. Velocity stream line also shows that the higher speeds occur in the near mouthguard, that is, between the bottom surfaces of the mouthguard and the lower teeth. The results demonstrated that the thicker the mouthguard, the better it is for prevention but less in air flow distribution into the oral cavity.

A Coding Scheme to Analyse the Online Asynchronous Discussion Forums of University Students

Science.gov (United States)

Biasutti, Michele

2017-01-01

The current study describes the development of a content analysis coding scheme to examine transcripts of online asynchronous discussion groups in higher education. The theoretical framework comprises the theories regarding knowledge construction in computer-supported collaborative learning (CSCL) based on a sociocultural perspective. The coding…

The Mechanical Transient Process at Asynchronous Motor Oscillating Mode

Science.gov (United States)

Antonovičs, Uldis; Bražis, Viesturs; Greivulis, Jānis

2009-01-01

The research object is squirrel-cage asynchronous motor connected to single-phase sinusoidal. There are shown, that by connecting to the stator windings a certain sequence of half-period positive and negative voltage, a motor rotor is rotated, but three times slower than in the three-phase mode. Changing the connecting sequence of positive and negative half-period voltage to stator windings, motor can work in various oscillating modes. It is tested experimentally. The mechanical transient processes had been researched in rotation and oscillating modes.

Hybrid inverse design method for nonlifting bodies in incompressible flow

CSIR Research Space (South Africa)

Broughton, BA

2006-11-01

Full Text Available A methodology for the inverse design of non-lifting axisymmetric bodies in compressible flow is presented. In this method, an inverse design approach based on conformal mapping is used to design a set of airfoils in isolation. These airfoils...

Orifice design for the control of coupled region flow

International Nuclear Information System (INIS)

Atherton, R.; Spadaro, P.R.; Brummerhop, F.G.

1975-01-01

A fluid system arrangement for nuclear reactors is described comprising a triplate orifice apparatus which simultaneously controls core flow distribution, flow rate ratio between hydraulically coupled regions of the blanket and radial static pressure gradients entering and leaving the blanket fuel region. The design of the apparatus is based on the parameters of the diameter of the orifice holes, the friction factor, and expansion, contraction and turning pressure loss coefficients of the geometry of each orifice region. These above parameters are properly matched to provide the desired pressure drop, flow split and negligible cross flow at the interface of standard and power-flattened open lattice blanket regions. (U.S.)

Comparison of a Ring On-Chip Network and a Code-Division Multiple-Access On-Chip Network

Directory of Open Access Journals (Sweden)

Xin Wang

2007-01-01

Full Text Available Two network-on-chip (NoC designs are examined and compared in this paper. One design applies a bidirectional ring connection scheme, while the other design applies a code-division multiple-access (CDMA connection scheme. Both of the designs apply globally asynchronous locally synchronous (GALS scheme in order to deal with the issue of transferring data in a multiple-clock-domain environment of an on-chip system. The two NoC designs are compared with each other by their network structures, data transfer principles, network node structures, and their asynchronous designs. Both the synchronous and the asynchronous designs of the two on-chip networks are realized using a hardware-description language (HDL in order to make the entire designs suit the commonly used synchronous design tools and flow. The performance estimation and comparison of the two NoC designs which are based on the HDL realizations are addressed. By comparing the two NoC designs, the advantages and disadvantages of applying direct connection and CDMA connection schemes in an on-chip communication network are discussed.

Design and optimization of mixed flow pump impeller blades by varying semi-cone angle

Science.gov (United States)

Dash, Nehal; Roy, Apurba Kumar; Kumar, Kaushik

2018-03-01

The mixed flow pump is a cross between the axial and radial flow pump. These pumps are used in a large number of applications in modern fields. For the designing of these mixed flow pump impeller blades, a lot number of design parameters are needed to be considered which makes this a tedious task for which fundamentals of turbo-machinery and fluid mechanics are always prerequisites. The semi-cone angle of mixed flow pump impeller blade has a specified range of variations generally between 45o to 60o. From the literature review done related to this topic researchers have considered only a particular semi-cone angle and all the calculations are based on this very same semi-cone angle. By varying this semi-cone angle in the specified range, it can be verified if that affects the designing of the impeller blades for a mixed flow pump. Although a lot of methods are available for designing of mixed flow pump impeller blades like inverse time marching method, the pseudo-stream function method, Fourier expansion singularity method, free vortex method, mean stream line theory method etc. still the optimized design of the mixed flow pump impeller blade has been a cumbersome work. As stated above since all the available research works suggest or propose the blade designs with constant semi-cone angle, here the authors have designed the impeller blades by varying the semi-cone angle in a particular range with regular intervals for a Mixed-Flow pump. Henceforth several relevant impeller blade designs are obtained and optimization is carried out to obtain the optimized design (blade with optimal geometry) of impeller blade.

Effects of synchronous versus asynchronous mode of propulsion on wheelchair basketball sprinting.

Science.gov (United States)

Faupin, Arnaud; Borel, Benoit; Meyer, Christophe; Gorce, Philippe; Watelain, Eric

2013-11-01

This study aimed to first investigate synchronous (SYN) versus asynchronous (ASY) mode of propulsion and, second, investigate the wheel camber effects on sprinting performance as well as temporal parameters. Seven wheelchair basketball players performed four maximal eight-second sprints on a wheelchair ergometer. They repeated the test according to two modes of propulsion (SYN and ASY) and two wheel cambers (9° and 15°). The mean maximal velocity and push power output was greater in the synchronous mode compared to the asynchronous mode for both camber angles. However, the fluctuation in the velocity profile is inferior for ASY versus SYN mode for both camber angles. Greater push time/cycle time (Pt/Ct) and arm frequency (AF) for synchronous mode versus asynchronous mode and inversely, lesser Ct and rest time (Rt) values for the synchronous mode, for which greater velocity were observed. SYN mode leads to better performance than ASY mode in terms of maximal propulsion velocity. However, ASY propulsion allows greater continuity of the hand-rim force application, reducing fluctuations in the velocity profile. The camber angle had no effect on ASY and SYN mean maximal velocity and push power output. The study of wheelchair propulsion strategies is important for better understanding physiological and biomechanical impacts of wheelchair propulsion for individuals with disabilities. From a kinematical point of view, this study highlights synchronous mode of propulsion to be more efficient, with regards to mean maximal velocity reaching during maximal sprinting exercises. Even if this study focuses on well-trained wheelchair athletes, results from this study could complement the knowledge on the physiological and biomechanical adaptations to wheelchair propulsion and therefore, might be interesting for wheelchair modifications for purposes of rehabilitation.

Quorum system and random based asynchronous rendezvous protocol for cognitive radio ad hoc networks

Directory of Open Access Journals (Sweden)

Sylwia Romaszko

2013-12-01

Full Text Available This paper proposes a rendezvous protocol for cognitive radio ad hoc networks, RAC2E-gQS, which utilizes (1 the asynchronous and randomness properties of the RAC2E protocol, and (2 channel mapping protocol, based on a grid Quorum System (gQS, and taking into account channel heterogeneity and asymmetric channel views. We show that the combination of the RAC2E protocol with the grid-quorum based channel mapping can yield a powerful RAC2E-gQS rendezvous protocol for asynchronous operation in a distributed environment assuring a rapid rendezvous between the cognitive radio nodes having available both symmetric and asymmetric channel views. We also propose an enhancement of the protocol, which uses a torus QS for a slot allocation, dealing with the worst case scenario, a large number of channels with opposite ranking lists.

Evaluating the Quality of Interaction in Asynchronous Discussion Forums in Fully Online Courses

Science.gov (United States)

Nandi, Dip; Hamilton, Margaret; Harland, James

2012-01-01

Fully online courses are becoming progressively more popular because of their "anytime anywhere" learning flexibility. One of the ways students interact with each other and with the instructors within fully online learning environments is via asynchronous discussion forums. However, student engagement in online discussion forums does not…

Studying the development of asynchronous rolling of the rotor over the stator with the turbine unit protection systems having different response times

Science.gov (United States)

Shatokhin, V. F.

2014-07-01

The possibility to stabilize the developing asynchronous rolling of the rotor over the stator under the conditions of power unit protections coming in action with different response times is considered. Asynchronous rolling of the rotor over the stator may develop when the rotating rotor comes in contact with the stator at high amplitudes of vibration caused by an abrupt loss of rotor balancing, by forced or self-excited vibration of the rotor, and by other factors. The danger of asynchronous rolling is connected with almost instantaneous development of self-excited vibration of the rotor when it comes in contact with the stator and with the rotor vibration amplitudes and forces of interaction between the rotor and stator dangerous for the turbine unit integrity. It is assumed that the turbine unit protection systems come in action after the arrival of signal of exceeding the permissible vibration level and produce commands to disconnect the generator from the grid, and to stop the supply of working fluid into the flow path, due to which an accelerating torque ceases to act on the turbine unit shaft. The protection system response speed is determined by a certain time t = ABtime that is taken for its components to come in action from the commencement of the event (application of the signal) to closure of the stop valves. The time curves of the main rolling parameters as functions of the ABtime value are presented. It is shown that the response time of existing protection systems is not sufficient for efficiently damping the rolling phenomenon, although the use of an electrical protection system (with the response time equal to 0.40-0.45 s) may have a positive effect on stabilizing the vibration amplitudes to a certain extent during the rolling and on smoothing its dangerous consequences. The consequences of rotor rolling over the stator can be efficiently mitigated by increasing the energy losses in the rotor-stator system (especially in the stator) and by

Effect of asynchrony on numerical simulations of fluid flow phenomena

Science.gov (United States)

Konduri, Aditya; Mahoney, Bryan; Donzis, Diego

2015-11-01

Designing scalable CFD codes on massively parallel computers is a challenge. This is mainly due to the large number of communications between processing elements (PEs) and their synchronization, leading to idling of PEs. Indeed, communication will likely be the bottleneck in the scalability of codes on Exascale machines. Our recent work on asynchronous computing for PDEs based on finite-differences has shown that it is possible to relax synchronization between PEs at a mathematical level. Computations then proceed regardless of the status of communication, reducing the idle time of PEs and improving the scalability. However, accuracy of the schemes is greatly affected. We have proposed asynchrony-tolerant (AT) schemes to address this issue. In this work, we study the effect of asynchrony on the solution of fluid flow problems using standard and AT schemes. We show that asynchrony creates additional scales with low energy content. The specific wavenumbers affected can be shown to be due to two distinct effects: the randomness in the arrival of messages and the corresponding switching between schemes. Understanding these errors allow us to effectively control them, rendering the method's feasibility in solving turbulent flows at realistic conditions on future computing systems.

BER and total throughput of asynchronous DS-OCDMA/WDM systems with multiple user interference

OpenAIRE

Ghiringhelli, F.; Zervas, M.N.

2003-01-01

The BER and throughput of Direct-Sequence OCDMA/WDM systems based on quadripolar codes and superstructured fiber Bragg gratings are statistically derived under asynchronous operation, intensity detection, and Multiple User Interference. Performance improvements with Forward Error Correction are included.

International service learning in the Dominican Republic: An asynchronous pilot in interprofessional education.

Science.gov (United States)

Foster, Jennifer; Pullen, Sara

2016-01-01

Despite the logistical barriers of asynchronous academic calendars, university students in nursing and physical therapy in one academic health centre piloted an international, interprofessional, service learning project in the Dominican Republic. Although the nursing students and physical therapy students were not able to be in-country at the same time, they provided care to a common caseload of traumatic injury patients and those with chronic, debilitating conditions. Interprofessional communication occurred with the development of SBAR (Situation, Background, Assessment, Recommendation) reports from the Team Training curriculum of the Agency for Healthcare Research and Quality. Students learned the depth of physical therapy and the breadth of nursing. The pilot led to a more refined design to pair nursing and PT students, requiring them to communicate via mobile phone regarding results of examinations, and suggestions for follow-up by the nursing students, to ensure continuity of care and a more comprehensive approach to services.

A geometric approach for fault detection and isolation of stator short circuit failure in a single asynchronous machine

KAUST Repository

Khelouat, Samir

2012-06-01

This paper deals with the problem of detection and isolation of stator short-circuit failure in a single asynchronous machine using a geometric approach. After recalling the basis of the geometric approach for fault detection and isolation in nonlinear systems, we will study some structural properties which are fault detectability and isolation fault filter existence. We will then design filters for residual generation. We will consider two approaches: a two-filters structure and a single filter structure, both aiming at generating residuals which are sensitive to one fault and insensitive to the other faults. Some numerical tests will be presented to illustrate the efficiency of the method.

Friend or foe? An exploratory study of Australian parents' use of asynchronous discussion boards in childhood obesity.

Science.gov (United States)

Appleton, Jessica; Fowler, Cathrine; Brown, Nicola

2014-01-01

The use of Internet and social media is increasing in every area of life. Parents are increasingly using online mediums to seek information about their children's health. Therefore, this is becoming an increasingly important topic area for health professionals to acknowledge. Developing an understanding about the dissemination of child health information through these online mediums will assist health professional to continue to engage and support parents to seek and share accurate and safe child health information. To explore parents' use of asynchronous online discussion boards for child health information seeking, advice and social support. A qualitative descriptive approach using an a priori template analysis was used to explore 34 discussions threads sampled from two Australian based online parenting discussion forums. To contain the scope of this study the threads chosen focused on childhood obesity in the Australian context. Four major themes related to parents' use of asynchronous online discussion boards were found. These were seeking advice, sharing advice, social support and making judgement. This final theme of making judgements included parents' perceptions of health professionals' advice. Asynchronous online discussion boards are online mediums being utilised for seeking and sharing child health related information and support between parents. The notion

Control or non-control state: that is the question! An asynchronous visual P300-based BCI approach

Science.gov (United States)

Pinegger, Andreas; Faller, Josef; Halder, Sebastian; Wriessnegger, Selina C.; Müller-Putz, Gernot R.

2015-02-01

Objective. Brain-computer interfaces (BCI) based on event-related potentials (ERP) were proven to be a reliable synchronous communication method. For everyday life situations, however, this synchronous mode is impractical because the system will deliver a selection even if the user is not paying attention to the stimulation. So far, research into attention-aware visual ERP-BCIs (i.e., asynchronous ERP-BCIs) has led to variable success. In this study, we investigate new approaches for detection of user engagement. Approach. Classifier output and frequency-domain features of electroencephalogram signals as well as the hybridization of them were used to detect the user's state. We tested their capabilities for state detection in different control scenarios on offline data from 21 healthy volunteers. Main results. The hybridization of classifier output and frequency-domain features outperformed the results of the single methods, and allowed building an asynchronous P300-based BCI with an average correct state detection accuracy of more than 95%. Significance. Our results show that all introduced approaches for state detection in an asynchronous P300-based BCI can effectively avoid involuntary selections, and that the hybrid method is the most effective approach.

Combining Synchronous and Asynchronous Collaboration within 3D City Models

Science.gov (United States)

Klimke, Jan; Döllner, Jürgen

This paper presents an approach for combining spatially distributed synchronous and asynchronous collaboration within 3D city models. Software applications use these models as additional communication medium to facilitate communication of georeferenced and geospatial information. Collaboration tools should support both the communication with other collaborators and their awareness of the current collaboration context. To support collaborative knowledge construction and gathering, we have designed a collaboration system to facilitate (a) creation of annotations that have 3D references to the virtual 3D city model and (b) collection information about the context in which these annotations are created. Our approach supports synchronous collaboration in connection with the creation of non volatile, precisely georeferenced units of information allow for a comprehensible form of cooperation in spatially distributed settings. Storage and retrieval of this information is provided through a Web Feature Service, which eases integration of collaboration data into existing applications. We further introduce a visualization technique that integrates annotations as complex structured data into the 3D visualization. This avoids media breaks and disruptions in working processes and creates a spatial coherence between annotation and annotated feature or geometry.

Analysis and design of flow limiter used in steam generator

International Nuclear Information System (INIS)

Liu Shixun; Gao Yongjun

1995-10-01

Flow limiter is an important safety component of PWR steam generator. It can limit the blowdown rate of steam generator inventory in case of the main steam pipeline breaks, so that the rate of the primary coolant temperature reduction can be slowed down in order to prevent fuel element from burn-out. The venturi type flow limiter is analysed, its flow characteristics are delineated, physical and mathematical models defined; the detail mathematical derivation provided. The research lays down a theoretic basis for flow limiter design. The governing equations and formulas given can be directly applied to computer analysis of the flow limiter. (3 refs., 3 figs.)

Asynchronous variational integration using continuous assumed gradient elements.

Science.gov (United States)

Wolff, Sebastian; Bucher, Christian

2013-03-01

Asynchronous variational integration (AVI) is a tool which improves the numerical efficiency of explicit time stepping schemes when applied to finite element meshes with local spatial refinement. This is achieved by associating an individual time step length to each spatial domain. Furthermore, long-term stability is ensured by its variational structure. This article presents AVI in the context of finite elements based on a weakened weak form (W2) Liu (2009) [1], exemplified by continuous assumed gradient elements Wolff and Bucher (2011) [2]. The article presents the main ideas of the modified AVI, gives implementation notes and a recipe for estimating the critical time step.

Improved Design of PECS to reduce Flow Instability for EU-APR1400

International Nuclear Information System (INIS)

Hwang, Do Hyun; Lee, Keunsung

2014-01-01

For EU-APR1400, PECS (Passive Ex-vessel corium retaining and Cooling System), so-called core catcher, was adopted to keep the integrity of basemat in containment by preventing MCCI (Molten Core Concrete Interaction) through retaining core debris and cooling corium outside the reactor vessel. In this paper, the improved design of PECS is presented to increase coolability by reducing flow instability in the region of cooling channel. In this paper, flow instability analysis was carried out using CFD code to find out the most improved design of PECS, which is to increase coolability by reducing bubble entrainment in the region of cooling channel. The reduction of bubble entrainment in the downcomer facilitates higher mass flow rates in the downcomer. Among presented four designed for the downcomer of PECS, the superstep design shows the highest mass flow rate and the lowest gas holdup in the downcomer as well as in the cooling channel. Compared with the existing design, the elimination of the horizontal part and the addition of an extra space above the vertical entrance to the downcomer seem to help the separation of the vapor

Participation in asynchronous online discussion forums does improve student learning of gross anatomy.

Science.gov (United States)

Green, Rodney A; Farchione, Davide; Hughes, Diane L; Chan, Siew-Pang

2014-01-01

Asynchronous online discussion forums are common in blended learning models and are popular with students. A previous report has suggested that participation in these forums may assist student learning in a gross anatomy subject but it was unclear as to whether more academically able students post more often or whether participation led to improved learning outcomes. This study used a path model to analyze the contribution of forum participation, previous academic ability, and student campus of enrolment to final marks in a multicampus gross anatomy course for physiotherapy students. The course has a substantial online learning management system (LMS) that incorporates asynchronous forums as a learning tool, particularly to answer learning objectives. Students were encouraged to post new threads and answer queries in threads started by others. The forums were moderated weekly by staff. Discussion forums were the most used feature of the LMS site with 31,920 hits. Forty-eight percent of the students posted at least once with 186 threads initiated by students and a total of 608 posts. The total number of posts made a significant direct contribution to final mark (P = 0.008) as did previous academic ability (P = 0.002). Although campus did not contribute to final mark, there was a trend for students at the campus where the course coordinator was situated to post more often than those at the other campus (P = 0.073). These results indicate that asynchronous online discussion forums can be an effective tool for improving student learning outcomes as evidenced by final marks in gross anatomy teaching. Copyright © 2013 American Association of Anatomists.

Multichannel readout ASIC design flow for high energy physics and cosmic rays experiments

International Nuclear Information System (INIS)

Voronin, A; Malankin, E

2016-01-01

In the large-scale high energy physics and astrophysics experiments multi-channel readout application specific integrated circuits (ASICs) are widely used. The ASICs for such experiments are complicated systems, which usually include both analog and digital building blocks. The complexity and large number of channels in such ASICs require the proper methodological approach to their design. The paper represents the mixed-signal design flow of the ASICs for high energy physics and cosmic rays experiments. This flow was successfully embedded to the development of the read-out ASIC prototype for the muon chambers of the CBM experiment. The approach was approved in UMC CMOS MMRF 180 nm process. The design flow enable to analyse the mixed-signal system operation on the different levels: functional, behavioural, schematic and post layout including parasitic elements. The proposed design flow allows reducing the simulation period and eliminating the functionality mismatches on the very early stage of the design. (paper)

Design of a miniature flow cell for in situ x-ray imaging of redox flow batteries

Science.gov (United States)

Jervis, Rhodri; Brown, Leon D.; Neville, Tobias P.; Millichamp, Jason; Finegan, Donal P.; Heenan, Thomas M. M.; Brett, Dan J. L.; Shearing, Paul R.

2016-11-01

Flow batteries represent a possible grid-scale energy storage solution, having many advantages such as scalability, separation of power and energy capabilities, and simple operation. However, they can suffer from degradation during operation and the characteristics of the felt electrodes are little understood in terms of wetting, compression and pressure drops. Presented here is the design of a miniature flow cell that allows the use of x-ray computed tomography (CT) to study carbon felt materials in situ and operando, in both lab-based and synchrotron CT. Through application of the bespoke cell it is possible to observe felt fibres, electrolyte and pore phases and therefore enables non-destructive characterisation of an array of microstructural parameters during the operation of flow batteries. Furthermore, we expect this design can be readily adapted to the study of other electrochemical systems.

Design of a miniature flow cell for in situ x-ray imaging of redox flow batteries

International Nuclear Information System (INIS)

Jervis, Rhodri; Brown, Leon D; Neville, Tobias P; Millichamp, Jason; Finegan, Donal P; Heenan, Thomas M M; Brett, Dan J L; Shearing, Paul R

2016-01-01

Flow batteries represent a possible grid-scale energy storage solution, having many advantages such as scalability, separation of power and energy capabilities, and simple operation. However, they can suffer from degradation during operation and the characteristics of the felt electrodes are little understood in terms of wetting, compression and pressure drops. Presented here is the design of a miniature flow cell that allows the use of x-ray computed tomography (CT) to study carbon felt materials in situ and operando , in both lab-based and synchrotron CT. Through application of the bespoke cell it is possible to observe felt fibres, electrolyte and pore phases and therefore enables non-destructive characterisation of an array of microstructural parameters during the operation of flow batteries. Furthermore, we expect this design can be readily adapted to the study of other electrochemical systems. (paper)

Computer-Aided Test Flow in Core-Based Design

OpenAIRE

Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

2000-01-01

This paper copes with the test-pattern generation and fault coverage determination in the core based design. The basic core-test strategy that one has to apply in the core-based design is stated in this work. A Computer-Aided Test (CAT) flow is proposed resulting in accurate fault coverage of embedded cores. The CAT now is applied to a few cores within the Philips Core Test Pilot IC project

Synaptotagmin-7 Is an Asynchronous Calcium Sensor for Synaptic Transmission in Neurons Expressing SNAP-23

DEFF Research Database (Denmark)

Weber, Jens P; Toft-Bertelsen, Trine L; Mohrmann, Ralf

2014-01-01

Synchronization of neurotransmitter release with the presynaptic action potential is essential for maintaining fidelity of information transfer in the central nervous system. However, synchronous release is frequently accompanied by an asynchronous release component that builds up during repetitive...... stimulation, and can even play a dominant role in some synapses. Here, we show that substitution of SNAP-23 for SNAP-25 in mouse autaptic glutamatergic hippocampal neurons results in asynchronous release and a higher frequency of spontaneous release events (mEPSCs). Use of neurons from double-knock-out (SNAP......, while synaptotagmin-7 barely displayed activity-dependent trafficking between vesicle and plasma membrane, implying that it acts as a plasma membrane calcium sensor. Overall, these findings support the idea of alternative syt∶SNARE combinations driving release with different kinetics and fidelity....

Asynchronous CMC, Collaboration and the Development of Critical Thinking in a Graduate Seminar in Applied Linguistics

Directory of Open Access Journals (Sweden)

Zsuzsanna I. Abrams

2005-06-01

Full Text Available A primary objective of graduate education, and often promoted by peer collaboration tasks, is the development of critical thinking skills. The present study compares how graduate students enrolled in a qualitative research design course in applied linguistics utilized asynchronous computer-mediated communication (ACMC and face-to-face interactions to critique field-specific research, to design and conduct their own research projects, and to engage in professional discourse in and out of class. The analyses reveal that 1 it was impossible to measure the development of critical thinking skills within one semester, and 2 rather than ACMC serving as a spring-board for such development prior to or in collaboration with classroom exchanges, ACMC and face-to-face interactions served different social and intellectual purposes in the process of practicing critical thinking skills. While face-to-face exchanges were preferred when discussing previous research, only in the ACMC context were students willing to critique each other’s work.

Asynchronous emergence by loggerhead turtle (Caretta caretta) hatchlings.

Science.gov (United States)

Houghton, J D; Hays, G C

2001-03-01

For many decades it has been accepted that marine turtle hatchlings from the same nest generally emerge from the sand together. However, for loggerhead turtles (Caretta caretta) nesting on the Greek Island of Kefalonia, a more asynchronous pattern of emergence has been documented. By placing temperature loggers at the top and bottom of nests laid on Kefalonia during 1998, we examined whether this asynchronous emergence was related to the thermal conditions within nests. Pronounced thermal variation existed not only between, but also within, individual nests. These within-nest temperature differences were related to the patterns of hatchling emergence, with hatchlings from nests displaying large thermal ranges emerging over a longer time-scale than those characterised by more uniform temperatures. In many egg-laying animals, parental care of the offspring may continue while the eggs are incubating and also after they have hatched. Consequently, the importance of the nest site for determining incubation conditions may be reduced since the parents themselves may alter the local environment. By contrast, in marine turtles, parental care ceases once the eggs have been laid and the nest site covered. The positioning of the nest site, in both space and time, may therefore have profound effects for marine turtles by affecting, for example, the survival of the eggs and hatchlings as well as their sex (Janzen and Paukstis 1991). During incubation, sea turtle embryos grow from a few cells at oviposition to a self-sufficient organism at hatching some 50-80 days later (Ackerman 1997). After hatching, the young turtles dig up through the sand and emerge typically en masse at the surface 1-7 nights later, with a number of stragglers following over the next few nights (Christens 1990). This contrasts with the frequently observed pattern of hatching asynchrony in birds. It has been suggested that the cause of mass emergence in turtles is that eggs within a clutch are fertilised

Effectiveness of an Asynchronous Online Module on University Students' Understanding of the Bohr Model of the Hydrogen Atom

Science.gov (United States)

Farina, William J.; Bodzin, Alec M.

2017-12-01

Web-based learning is a growing field in education, yet empirical research into the design of high quality Web-based university science instruction is scarce. A one-week asynchronous online module on the Bohr Model of the atom was developed and implemented guided by the knowledge integration framework. The unit design aligned with three identified metaprinciples of science learning: making science accessible, making thinking visible, and promoting autonomy. Students in an introductory chemistry course at a large east coast university completed either an online module or traditional classroom instruction. Data from 99 students were analyzed and results showed significant knowledge growth in both online and traditional formats. For the online learning group, findings revealed positive student perceptions of their learning experiences, highly positive feedback for online science learning, and an interest amongst students to learn chemistry within an online environment.

Mechanical Design of a Performance Test Rig for the Turbine Air-Flow Task (TAFT)

Science.gov (United States)

Forbes, John C.; Xenofos, George D.; Farrow, John L.; Tyler, Tom; Williams, Robert; Sargent, Scott; Moharos, Jozsef

2004-01-01

To support development of the Boeing-Rocketdyne RS84 rocket engine, a full-flow, reaction turbine geometry was integrated into the NASA-MSFC turbine air-flow test facility. A mechanical design was generated which minimized the amount of new hardware while incorporating all test and instrumentation requirements. This paper provides details of the mechanical design for this Turbine Air-Flow Task (TAFT) test rig. The mechanical design process utilized for this task included the following basic stages: Conceptual Design. Preliminary Design. Detailed Design. Baseline of Design (including Configuration Control and Drawing Revision). Fabrication. Assembly. During the design process, many lessons were learned that should benefit future test rig design projects. Of primary importance are well-defined requirements early in the design process, a thorough detailed design package, and effective communication with both the customer and the fabrication contractors.

Design and Realization of Intelligent Flow Controller

Directory of Open Access Journals (Sweden)

Jianxiong Ye

2014-09-01

Full Text Available According to accurate flow rate control requirements in large irrigation zone, a fuzzy controller with dead-band is designed on the characteristics analysis and comparison of PID and Fuzzy. The setting values of water flow for gates are determined by real-time water level detection sensors, and the realistic value of discharged water and gate opening are detected out with relative sensors, simulation manifest that the specific control strategy can adjust the gate swiftly in circumstance of huge offset, and regulate the gate slightly in time of small bias, it is realized with Siemens S315 PLC (Programmable Logical Controller and has being working steadily for 2 years, the aim of regulation is performed properly.

Numerical simulation of air flow through turbocharger compressors with dual volute design

Energy Technology Data Exchange (ETDEWEB)

Jiao, Kui; Li, Xianguo; Wu, Hao [Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, ON (Canada); Sun, Harold; Schram, Tim [Ford Motor Company, Dearborn, MI 48126 (United States); Krivitzky, Eric; Larosiliere, Louis M. [Concepts NREC, White River Junction, VT 05001 (United States)

2009-11-15

In this paper, turbocharger centrifugal compressors with dual volute design were investigated by using Computational Fluid Dynamics (CFD) method. The numerical simulation focused on the air flow from compressor impeller inlet to volute exit, and the overall performance level and range are predicted. The numerical investigation revealed that the dual volute design could separate the compressor into two operating regions: ''high efficiency'' and ''low efficiency'' regions with different air flow characteristics, and treating these two regions separately with dual diffuser design showed extended stable operating range and improved efficiency by comparing with conventional single volute design. The ''dual sequential volute'' concept also showed the potential to further extend the stable operating range by closing one of the volutes at low air flow rates. Furthermore, by comparing with other alternate designs such as variable diffuser vanes and variable inlet guide vanes, the operation of the dual sequential volute also features relatively simple control and calibration. (author)

The flow of financial resources : An inevitable part of supply chain design activities

OpenAIRE

Hofmann, Erik

2007-01-01

Supply chain managers do not only face the challenge of designing material and information flows. They also need to arrange the flow of financial resources. The financial side of supply chain design comprises all the economic aspects that result from collaborative concepts and applications. This paper provides an introduction into the field of cash flow organization in supply chains by presenting a collaborative payment model and its common instruments.

The Effect of Synchronous and Asynchronous Participation on Students' Performance in Online Accounting Courses

Science.gov (United States)

Duncan, Keith; Kenworthy, Amy; McNamara, Ray

2012-01-01

This article examines the relationship between MBA students' performance and participation in two online environments: a synchronous forum (chat room) and an asynchronous forum (discussion board) at an Australian university. The "quality" and "quantity" of students' participation is used to predict their final examination and…

The Role of Beliefs and Motivation in Asynchronous Online Learning in College-Level Classes

Science.gov (United States)

Xie, Kui; Huang, Kun

2014-01-01

Epistemic and learning beliefs were found to affect college students' cognitive engagement and study strategies, as well as motivation in classroom settings. However, the relationships between epistemic and learning beliefs, motivation, learning perception, and students' actual learning participation in asynchronous online settings have been…

Designing ecological flows to gravely braided rivers in alpine environments

Science.gov (United States)

Egozi, R.; Ashmore, P.

2009-04-01

Designing ecological flows in gravelly braided streams requires estimating the channel forming discharge in order to maintain the braided reach physical (allocation of flow and bed load) and ecological (maintaining the habitat diversity) functions. At present, compared to single meander streams, there are fewer guiding principles for river practitioners that can be used to manage braided streams. Insight into braiding morphodynamics using braiding intensity indices allows estimation of channel forming discharge. We assess variation in braiding intensity by mapping the total number of channels (BIT) and the number of active (transporting bed load) channels (BIA) at different stages of typical diurnal melt-water hydrographs in a pro-glacial braided river, Sunwapta River, Canada. Results show that both BIA and BIT vary with flow stage but over a limited range of values. Furthermore, maximum BIT occurs below peak discharge. At this stage there is a balance between channel merging from inundation and occupation of new channels as the stage rises. This stage is the channel forming discharge because above this stage the existing braided pattern cannot discharge the volume of water without causing morphological changes (e.g., destruction of bifurcations, channel avulsion). Estimation of the channel forming discharge requires a set of braiding intensity measurements over a range of flow stages. The design of ecological flows must take into consideration flow regime characteristics rather than just the channel forming discharge magnitude.

A BMI-based occupational therapy assist suit: asynchronous control by SSVEP.

Science.gov (United States)

Sakurada, Takeshi; Kawase, Toshihiro; Takano, Kouji; Komatsu, Tomoaki; Kansaku, Kenji

2013-01-01

A brain-machine interface (BMI) is an interface technology that uses neurophysiological signals from the brain to control external machines. Recent invasive BMI technologies have succeeded in the asynchronous control of robot arms for a useful series of actions, such as reaching and grasping. In this study, we developed non-invasive BMI technologies aiming to make such useful movements using the subject's own hands by preparing a BMI-based occupational therapy assist suit (BOTAS). We prepared a pre-recorded series of useful actions-a grasping-a-ball movement and a carrying-the-ball movement-and added asynchronous control using steady-state visual evoked potential (SSVEP) signals. A SSVEP signal was used to trigger the grasping-a-ball movement and another SSVEP signal was used to trigger the carrying-the-ball movement. A support vector machine was used to classify EEG signals recorded from the visual cortex (Oz) in real time. Untrained, able-bodied participants (n = 12) operated the system successfully. Classification accuracy and time required for SSVEP detection were ~88% and 3 s, respectively. We further recruited three patients with upper cervical spinal cord injuries (SCIs); they also succeeded in operating the system without training. These data suggest that our BOTAS system is potentially useful in terms of rehabilitation of patients with upper limb disabilities.

A Study of Synchronous versus Asynchronous Collaboration in an Online Business Writing Class

Science.gov (United States)

Mabrito, Mark

2006-01-01

A case study examined the collaborative experiences of students in an online business writing classroom. The purpose was to examine the same groups of students working on collaborative writing assignments in both a synchronous (real-time) and an asynchronous (non-real-time) discussion forum. This study focused on examining the amount, pattern, and…

Modifying Dialogical Strategy in Asynchronous Critical Discussions for Cross-Strait Chinese Learners

Directory of Open Access Journals (Sweden)

Jean Yiching Chiu

2014-09-01

Full Text Available In this global era, critical thinking has become crucial for educators and learners. The purpose of this research was to explore how modifying a dialogical strategy in asynchronous online discussion forums impacted Chinese learners’ critical thinking. Due to the Chinese cultural impact of social harmony, the majority of learners tend to maintain silent and avoid critical discussions in instructional settings. The author deployed an affectively supportive model in a modified dialogical strategy to structure Chinese EFL learners’ asynchronous critical postings by probing and questioning while requiring labeling of each cross-referencing posting as Agree/Disagree/Challenge/New Perspective. The participants were two cohorts of similar cultural background but under different political systems in China and Taiwan, here engaged together in cultural interactions. This study employed two research methods: standardized critical thinking tests, and focus groups. Findings reveal that learners in both cohorts indicated some improvement in their critical thinking skills. Nevertheless, there remain affective and cultural issues. Future studies are thus recommended to further investigate the potential of an adaptive model to engage critical discussions with English native speakers and optimize critical thinking for Chinese learners in an EFL environment.

A nuclear data acquisition system flow control model

International Nuclear Information System (INIS)

Hack, S.N.

1988-01-01

A general Petri Net representation of a nuclear data acquisition system model is presented. This model provides for the unique requirements of a nuclear data acquisition system including the capabilities of concurrently acquiring asynchronous and synchronous data, of providing multiple priority levels of flow control arbitration, and of permitting multiple input sources to reside at the same priority without the problem of channel lockout caused by a high rate data source. Finally, a previously implemented gamma camera/physiological signal data acquisition system is described using the models presented

Breaking The Millisecond Barrier On SpiNNaker: Implementing Asynchronous Event-Based Plastic Models With Microsecond Resolution

Directory of Open Access Journals (Sweden)

Xavier eLagorce

2015-06-01

Full Text Available Spike-based neuromorphic sensors such as retinas and cochleas, change the way in which the world is sampled. Instead of producing data sampled at a constant rate, these sensors output spikes that are asynchronous and event driven. The event-based nature of neuromorphic sensors implies a complete paradigm shift in current perception algorithms towards those that emphasize the importance of precise timing. The spikes produced by these sensors usually have a time resolution in the order of microseconds. This high temporal resolution is a crucial factor in learning tasks. It is also widely used in the field of biological neural networks. Sound localization for instance relies on detecting time lags between the two ears which, in the barn owl, reaches a temporal resolution of 5 microseconds. Current available neuromorphic computation platforms such as SpiNNaker often limit their users to a time resolution in the order of milliseconds that is not compatible with the asynchronous outputs of neuromorphic sensors. To overcome these limitations and allow for the exploration of new types of neuromorphic computing architectures, we introduce a novel software framework on the SpiNNaker platform. This framework allows for simulations of spiking networks and plasticity mechanisms using a completely asynchronous and event-based scheme running with a microsecond time resolution. Results on two example networks using this new implementation are presented.

A 0.8mW 250MS/s time-interleaved asynchronous digital slope ADC

NARCIS (Netherlands)

Harpe, P.J.A.; Zhou, C.; Philips, K.J.P.; Groot, de H.W.H.

2010-01-01

Slope and digital-ramp converters are normally limited to very low sampling rates, since they require a digital counter at a highly oversampled clock rate. In this work, an asynchronous digital slope architecture is introduced that only requires a non-oversampled clock, thus enabling a much higher

IHadoop: Asynchronous iterations for MapReduce

KAUST Repository

Elnikety, Eslam Mohamed Ibrahim

2011-11-01

MapReduce is a distributed programming frame-work designed to ease the development of scalable data-intensive applications for large clusters of commodity machines. Most machine learning and data mining applications involve iterative computations over large datasets, such as the Web hyperlink structures and social network graphs. Yet, the MapReduce model does not efficiently support this important class of applications. The architecture of MapReduce, most critically its dataflow techniques and task scheduling, is completely unaware of the nature of iterative applications; tasks are scheduled according to a policy that optimizes the execution for a single iteration which wastes bandwidth, I/O, and CPU cycles when compared with an optimal execution for a consecutive set of iterations. This work presents iHadoop, a modified MapReduce model, and an associated implementation, optimized for iterative computations. The iHadoop model schedules iterations asynchronously. It connects the output of one iteration to the next, allowing both to process their data concurrently. iHadoop\\'s task scheduler exploits inter-iteration data locality by scheduling tasks that exhibit a producer/consumer relation on the same physical machine allowing a fast local data transfer. For those iterative applications that require satisfying certain criteria before termination, iHadoop runs the check concurrently during the execution of the subsequent iteration to further reduce the application\\'s latency. This paper also describes our implementation of the iHadoop model, and evaluates its performance against Hadoop, the widely used open source implementation of MapReduce. Experiments using different data analysis applications over real-world and synthetic datasets show that iHadoop performs better than Hadoop for iterative algorithms, reducing execution time of iterative applications by 25% on average. Furthermore, integrating iHadoop with HaLoop, a variant Hadoop implementation that caches

IHadoop: Asynchronous iterations for MapReduce

KAUST Repository

Elnikety, Eslam Mohamed Ibrahim; El Sayed, Tamer S.; Ramadan, Hany E.

2011-01-01

MapReduce is a distributed programming frame-work designed to ease the development of scalable data-intensive applications for large clusters of commodity machines. Most machine learning and data mining applications involve iterative computations over large datasets, such as the Web hyperlink structures and social network graphs. Yet, the MapReduce model does not efficiently support this important class of applications. The architecture of MapReduce, most critically its dataflow techniques and task scheduling, is completely unaware of the nature of iterative applications; tasks are scheduled according to a policy that optimizes the execution for a single iteration which wastes bandwidth, I/O, and CPU cycles when compared with an optimal execution for a consecutive set of iterations. This work presents iHadoop, a modified MapReduce model, and an associated implementation, optimized for iterative computations. The iHadoop model schedules iterations asynchronously. It connects the output of one iteration to the next, allowing both to process their data concurrently. iHadoop's task scheduler exploits inter-iteration data locality by scheduling tasks that exhibit a producer/consumer relation on the same physical machine allowing a fast local data transfer. For those iterative applications that require satisfying certain criteria before termination, iHadoop runs the check concurrently during the execution of the subsequent iteration to further reduce the application's latency. This paper also describes our implementation of the iHadoop model, and evaluates its performance against Hadoop, the widely used open source implementation of MapReduce. Experiments using different data analysis applications over real-world and synthetic datasets show that iHadoop performs better than Hadoop for iterative algorithms, reducing execution time of iterative applications by 25% on average. Furthermore, integrating iHadoop with HaLoop, a variant Hadoop implementation that caches

INFLUENCE OF THE TIME OF DISINHIBITION TO TRANSIENTS AND WEAR OF THE FRICTION LININGS IN AN ASYNCHRONOUS MOTOR

Directory of Open Access Journals (Sweden)

V. V. Solencov

2016-01-01

Full Text Available Time and the stopping distance of the electric drive with frequent starting-and-braking modes that contain embedded asynchronous motor with a recessed combined braking device depend on the moment of an electromagnet disinhibition. At the same time other important criteria are taken into the account, i.e. wear resistance of the brake device and the smoothness of the deceleration of the electric drive. In general such an asynchronous motor contains asynchronous engine with squirrel-cage rotor, electromechanical normally-closed brake, electromagnetical slip clutch and control circuit. The mechanical characteristics of the deceleration of asynchronous motor with recessed combined brake device at different moments of an electromagnet disinhibition are presented. The mathematical model is featured and the transients in such a motor are presented. Formation models for computer research were carried out in the Fortran 2008 programming language. Calculation of the system of differential equations was fulfilled by the Runge – Kutta method. The deceleration of the electromechanical brake at various speeds caused different time values and stopping distances. The plots of stopping distance and the braking time at various moments of an electromagnet disinhibition are demonstrated. The optimum moment of switching on an electromechanical brake, providing small stopping distance and the braking time is the time when the speed wвкл = 0,6–0,8 of the nominal. In this case the acceptable number of brake applications for friction linings (compared with mechanical braking will increase by 1.6–2.8 times. The pilot study confirmed the validity of the obtained mathematical models and discovered patterns.

Emergency evacuation : how better interior design can improve passenger flow

NARCIS (Netherlands)

Boer, L.C.; Skjong, R.

2001-01-01

The paper presents some conclusions from the EU basic research project "MEPdesign" relevant for design of ship interiors. The findings are discussed with regard to passenger flow as a function of design parameters. The paper explains that current evacuation analyses may be overly optimistic. The

Experimental study of lithium free-surface flow for IFMIF target design

International Nuclear Information System (INIS)

Kondo, H.; Fujisato, A.; Yamaoka, N.; Inoue, S.; Miyamoto, S.; Iida, T.; Nakamura, H.; Ida, M.; Matushita, I.; Muroga, T.; Horiike, H.

2006-01-01

Lithium free-surface flow experiments to verify the design of IFMIF target have been carried out at Osaka University. The present report summarizes experimental results of surface phenomena, and cavitation characteristics of the loop, so as to try to apply these results to design parameters. Waves on the lithium flow surface is similar to that on water, and can be predicted by a linear stability theory. The wave amplitude is measured by an electro-contact probe. Surface roughness on a target nozzle, caused for example by attached chemical compounds and/or wastages by erosion and corrosion, can lead to a significant loss of target flow stability as well as surface wakes. The need of a polishing manipulator or exchange of the nozzle may be anticipated. Cavitation characteristic of the loop was measured by an accelerometer. From the results, a friction factor could be estimated fort he lithium flow

Design of Capillary Flows with Spatially Graded Porous Films

Science.gov (United States)

Joung, Young Soo; Figliuzzi, Bruno Michel; Buie, Cullen

2013-11-01

We have developed a new capillary tube model, consisting of multi-layered capillary tubes oriented in the direction of flow, to predict capillary speeds on spatially graded porous films. Capillary flows through thin porous media have been widely utilized for small size liquid transport systems. However, for most media it is challenging to realize arbitrary shapes and spatially functionalized micro-structures with variable flow properties. Therefore, conventional media can only be used for capillary flows obeying Washburn's equation and the modifications thereof. Given this background, we recently developed a method called breakdown anodization (BDA) to produce highly wetting porous films. The resulting surfaces show nearly zero contact angles and fast water spreading speed. Furthermore, capillary pressure and spreading diffusivity can be expressed as functions of capillary height when customized electric fields are used in BDA. From the capillary tube model, we derived a general capillary flow equation of motion in terms of capillary pressure and spreading diffusivity. The theoretical model shows good agreement with experimental capillary flows. The study will provide novel design methodologies for paper-based microfluidic devices.

Construction and performance analysis of variable-weight optical orthogonal codes for asynchronous OCDMA systems

Science.gov (United States)

Li, Chuan-qi; Yang, Meng-jie; Zhang, Xiu-rong; Chen, Mei-juan; He, Dong-dong; Fan, Qing-bin

2014-07-01

A construction scheme of variable-weight optical orthogonal codes (VW-OOCs) for asynchronous optical code division multiple access (OCDMA) system is proposed. According to the actual situation, the code family can be obtained by programming in Matlab with the given code weight and corresponding capacity. The formula of bit error rate (BER) is derived by taking account of the effects of shot noise, avalanche photodiode (APD) bulk, thermal noise and surface leakage currents. The OCDMA system with the VW-OOCs is designed and improved. The study shows that the VW-OOCs have excellent performance of BER. Despite of coming from the same code family or not, the codes with larger weight have lower BER compared with the other codes in the same conditions. By taking simulation, the conclusion is consistent with the analysis of BER in theory. And the ideal eye diagrams are obtained by the optical hard limiter.

Interaction of impeller and guide vane in a series-designed axial-flow pump

International Nuclear Information System (INIS)

Kim, S; Choi, Y S; Lee, K Y; Kim, J H

2012-01-01

In this paper, the interaction of the impeller and guide vane in a series-designed axial-flow pump was examined through the implementation of a commercial CFD code. The impeller series design refers to the general design procedure of the base impeller shape which must satisfy the various flow rate and head requirements by changing the impeller setting angle and number of blades of the base impeller. An arc type meridional shape was used to keep the meridional shape of the hub and shroud with various impeller setting angles. The blade angle and the thickness distribution of the impeller were designed as an NACA airfoil type. In the design of the guide vane, it was necessary to consider the outlet flow condition of the impeller with the given setting angle. The meridional shape of the guide vane were designed taking into consideration the setting angle of the impeller, and the blade angle distribution of the guide vane was determined with a traditional design method using vane plane development. In order to achieve the optimum impeller design and guide vane, three-dimensional computational fluid dynamics and the DOE method were applied. The interaction between the impeller and guide vane with different combination set of impeller setting angles and number of impeller blades was addressed by analyzing the flow field of the computational results.

Numerical investigation on the energetic performances of conventional and pellet aftertreatment systems in flow-through and reverse-flow designs

Directory of Open Access Journals (Sweden)

Morrone Pietropaolo

2011-01-01

Full Text Available The aim of the paper is the analysis of the energetic performances of structured and pelletized aftertreatment systems in flow-through and reverse-flow designs (passive and active flow control respectively for diesel internal combustion engines. To this purpose, the influence of the engine operating conditions on the system performances has been investigated adopting a one-dimensional time-dependent model. Specifically, the thermal behaviour and the fuel saving capability of several arrangements have been characterized. The analysis has shown that the active emission control system with pelletized design guarantees higher heat retention capability. Furthermore, the numerical model has revealed the significant influence of the solid and exhaust gas temperature on the energy efficiency of the aftertreatment systems and the large effect of exhaust mass flow rate and unburned hydrocarbons concentration.

Temperature, paternity and asynchronous hatching influence early developmental characteristics of larval Atlantic cod, Gadus morhua

DEFF Research Database (Denmark)

Politis, Sebastian Nikitas; Dahlke, Flemming T.; Butts, Ian A.E.

2014-01-01

Offspring, especially during early development, are influenced by both intrinsic properties endowed to them by their parents, extrinsic environmental factors as well as the interplay between genes and the environment. We investigated the effects of paternity (P), temperature (T), and asynchronous...

Frog: Asynchronous Graph Processing on GPU with Hybrid Coloring Model

Energy Technology Data Exchange (ETDEWEB)

Shi, Xuanhua; Luo, Xuan; Liang, Junling; Zhao, Peng; Di, Sheng; He, Bingsheng; Jin, Hai

2018-01-01

GPUs have been increasingly used to accelerate graph processing for complicated computational problems regarding graph theory. Many parallel graph algorithms adopt the asynchronous computing model to accelerate the iterative convergence. Unfortunately, the consistent asynchronous computing requires locking or atomic operations, leading to significant penalties/overheads when implemented on GPUs. As such, coloring algorithm is adopted to separate the vertices with potential updating conflicts, guaranteeing the consistency/correctness of the parallel processing. Common coloring algorithms, however, may suffer from low parallelism because of a large number of colors generally required for processing a large-scale graph with billions of vertices. We propose a light-weight asynchronous processing framework called Frog with a preprocessing/hybrid coloring model. The fundamental idea is based on Pareto principle (or 80-20 rule) about coloring algorithms as we observed through masses of realworld graph coloring cases. We find that a majority of vertices (about 80%) are colored with only a few colors, such that they can be read and updated in a very high degree of parallelism without violating the sequential consistency. Accordingly, our solution separates the processing of the vertices based on the distribution of colors. In this work, we mainly answer three questions: (1) how to partition the vertices in a sparse graph with maximized parallelism, (2) how to process large-scale graphs that cannot fit into GPU memory, and (3) how to reduce the overhead of data transfers on PCIe while processing each partition. We conduct experiments on real-world data (Amazon, DBLP, YouTube, RoadNet-CA, WikiTalk and Twitter) to evaluate our approach and make comparisons with well-known non-preprocessed (such as Totem, Medusa, MapGraph and Gunrock) and preprocessed (Cusha) approaches, by testing four classical algorithms (BFS, PageRank, SSSP and CC). On all the tested applications and

A comparison of classroom and online asynchronous problem-based learning for students undertaking statistics training as part of a Public Health Masters degree.

Science.gov (United States)

de Jong, N; Verstegen, D M L; Tan, F E S; O'Connor, S J

2013-05-01

This case-study compared traditional, face-to-face classroom-based teaching with asynchronous online learning and teaching methods in two sets of students undertaking a problem-based learning module in the multilevel and exploratory factor analysis of longitudinal data as part of a Masters degree in Public Health at Maastricht University. Students were allocated to one of the two study variants on the basis of their enrolment status as full-time or part-time students. Full-time students (n = 11) followed the classroom-based variant and part-time students (n = 12) followed the online asynchronous variant which included video recorded lectures and a series of asynchronous online group or individual SPSS activities with synchronous tutor feedback. A validated student motivation questionnaire was administered to both groups of students at the start of the study and a second questionnaire was administered at the end of the module. This elicited data about student satisfaction with the module content, teaching and learning methods, and tutor feedback. The module coordinator and problem-based learning tutor were also interviewed about their experience of delivering the experimental online variant and asked to evaluate its success in relation to student attainment of the module's learning outcomes. Student examination results were also compared between the two groups. Asynchronous online teaching and learning methods proved to be an acceptable alternative to classroom-based teaching for both students and staff. Educational outcomes were similar for both groups, but importantly, there was no evidence that the asynchronous online delivery of module content disadvantaged part-time students in comparison to their full-time counterparts.

Design and setup of intermittent-flow respirometry system for aquatic organisms

DEFF Research Database (Denmark)

Svendsen, Morten Bo Søndergaard; Bushnell, P.G.; Steffensen, John Fleng

2016-01-01

Intermittent-flow respirometry is an experimental protocol for measuring oxygen consumption in aquatic organisms that utilizes the best features of closed (stop-flow) and flow-through respirometry while eliminating (or at least reducing) some of their inherent problems. By interspersing short...... and software further reduces error by allowing many measurements to be made over long periods thereby minimizing animal stress due to acclimation issues. This paper describes some of the fundamental principles that need to be considered when designing and carrying out automated intermittent-flow respirometry...

Student Outcomes Associated with Use of Asynchronous Online Discussion Forums in Gross Anatomy Teaching

Science.gov (United States)

Green, Rodney A.; Hughes, Diane L.

2013-01-01

Asynchronous online discussion forums are increasingly common in blended learning environments but the relationship to student learning outcomes has not been reported for anatomy teaching. Forums were monitored in two multicampus anatomy courses; an introductory first year course and a second year physiotherapy-specific course. The forums are…

Peer Moderation of Asynchronous Online Discussions: An Exploratory Study of Peer E-Moderating Behaviour

Science.gov (United States)

Ghadirian, Hajar; Ayub, Ahmad Fauzi Mohd

2017-01-01

This study explored patterns of e-moderating behaviour students performed when they were assigned as peer moderators of asynchronous online discussions in a reciprocal manner. Eighty-four students from an undergraduate blended course were observed during a 7-week-long online discussions. Using quantitative content analysis peer moderators'…

Students' Desired and Experienced Levels of Connectivity to an Asynchronous, Online, Distance Degree Program

Science.gov (United States)

Schroeder, Shawnda; Baker, Mary; Terras, Katherine; Mahar, Patti; Chiasson, Kari

2016-01-01

This study examined graduate students' desired and experienced levels of connectivity in an online, asynchronous distance degree program. Connectivity was conceptualized as the students' feelings of community and involvement, not their level of access to the Internet. Graduate students enrolled in a distance degree program were surveyed on both…

XMPP for cloud computing in bioinformatics supporting discovery and invocation of asynchronous web services.

Science.gov (United States)

Wagener, Johannes; Spjuth, Ola; Willighagen, Egon L; Wikberg, Jarl E S

2009-09-04

Life sciences make heavily use of the web for both data provision and analysis. However, the increasing amount of available data and the diversity of analysis tools call for machine accessible interfaces in order to be effective. HTTP-based Web service technologies, like the Simple Object Access Protocol (SOAP) and REpresentational State Transfer (REST) services, are today the most common technologies for this in bioinformatics. However, these methods have severe drawbacks, including lack of discoverability, and the inability for services to send status notifications. Several complementary workarounds have been proposed, but the results are ad-hoc solutions of varying quality that can be difficult to use. We present a novel approach based on the open standard Extensible Messaging and Presence Protocol (XMPP), consisting of an extension (IO Data) to comprise discovery, asynchronous invocation, and definition of data types in the service. That XMPP cloud services are capable of asynchronous communication implies that clients do not have to poll repetitively for status, but the service sends the results back to the client upon completion. Implementations for Bioclipse and Taverna are presented, as are various XMPP cloud services in bio- and cheminformatics. XMPP with its extensions is a powerful protocol for cloud services that demonstrate several advantages over traditional HTTP-based Web services: 1) services are discoverable without the need of an external registry, 2) asynchronous invocation eliminates the need for ad-hoc solutions like polling, and 3) input and output types defined in the service allows for generation of clients on the fly without the need of an external semantics description. The many advantages over existing technologies make XMPP a highly interesting candidate for next generation online services in bioinformatics.

Design of mass flow rate measurement system for SST-1 superconducting magnet system

Energy Technology Data Exchange (ETDEWEB)

Varmora, P., E-mail: pvamora@ipr.res.in; Sharma, A.N.; Khristi, Y.; Prasad, U.; Patel, D.; Doshi, K.; Pradhan, S.

2016-11-15

Highlights: • Design of Venturi meter for SST-1 magnet system. • Details of Helium mass flow measurement system used in SST-1. • Instruments and measurement techniques for flow measurement. • VME based data acquisition system details and flow calculation and results from SST-1 campaigns. - Abstract: Superconducting Magnet System (SCMS) of Steady State Superconducting Tokamak – 1 (SST-1) is forced-flow cooled by a closed cycle 1.3 kW (at 4.5 K) class Helium Refrigerator cum Liquefier (HRL) system. An accurate measurement of helium mass flow rate in different coils is required to ensure the uniform cooling of the cold mass in the entire range of operating temperature (300 K to 4.5 K) and pressure (0.9–0.4 MPa). To meet this requirement, indigenously designed and fabricated venturi meters are installed on 27 different coils of SST-1 SCMS. A VME based Data Acquisition System (DAS) has been developed and used to acquire the flow measurement data from different flowmeters. The details of the design of venturi meter, its different measurement and signal conditioning components, the data acquisition system and the mass flow rate calculation method are described in this paper. The mass flow rate measurement data from cryogenic acceptance and SST-1 magnet commissioning experiments are also presented and discussed in this paper.

Design of mass flow rate measurement system for SST-1 superconducting magnet system

International Nuclear Information System (INIS)

Varmora, P.; Sharma, A.N.; Khristi, Y.; Prasad, U.; Patel, D.; Doshi, K.; Pradhan, S.

2016-01-01

Highlights: • Design of Venturi meter for SST-1 magnet system. • Details of Helium mass flow measurement system used in SST-1. • Instruments and measurement techniques for flow measurement. • VME based data acquisition system details and flow calculation and results from SST-1 campaigns. - Abstract: Superconducting Magnet System (SCMS) of Steady State Superconducting Tokamak – 1 (SST-1) is forced-flow cooled by a closed cycle 1.3 kW (at 4.5 K) class Helium Refrigerator cum Liquefier (HRL) system. An accurate measurement of helium mass flow rate in different coils is required to ensure the uniform cooling of the cold mass in the entire range of operating temperature (300 K to 4.5 K) and pressure (0.9–0.4 MPa). To meet this requirement, indigenously designed and fabricated venturi meters are installed on 27 different coils of SST-1 SCMS. A VME based Data Acquisition System (DAS) has been developed and used to acquire the flow measurement data from different flowmeters. The details of the design of venturi meter, its different measurement and signal conditioning components, the data acquisition system and the mass flow rate calculation method are described in this paper. The mass flow rate measurement data from cryogenic acceptance and SST-1 magnet commissioning experiments are also presented and discussed in this paper.

Design of a naturalized flow regime—An example from the Lower Missouri River, USA

Science.gov (United States)

Jacobson, Robert B.; Galat, David L.

2008-01-01

 group of river managers, stakeholders, and scientists met during summer 2005 to design a more naturalized flow regime for the Lower Missouri River (LMOR). The objective was to comply with requirements under the U.S. Endangered Species Act to support reproduction and survival of threatened and endangered species, with emphasis on the endangered pallid sturgeon (Scaphirhynchus albus), while minimizing negative effects to existing social and economic benefits of prevailing river management. Specific hydrograph requirements for pallid sturgeon reproduction are unknown, hence much of the design process was based on features of the natural flow regime. Environmental flow components (EFCs) extracted from the reference natural flow regime were used to design and assess performance of alternative flow regimes.The design process incorporated a primary stage in which conceptual hydrographs were developed and assessed for their general ecological and social-economic performance. The second stage accounted for hydroclimatic variation by coding the conceptual hydrographs into reservoir release rules, adding constraints for downstream flooding and low-storage precludes, and running the rules through 100 years of hydroclimatic simulation. The output flow regimes were then evaluated for presumed ecological benefits based on how closely they resembled EFCs in the reference natural flow regime. Flow regimes also were assessed for social-economic cost indicators, including days of flooding of low-lying agricultural land, days over flood stage, and storage levels in system reservoirs.Our experience with flow-regime design on the LMOR underscored the lack of confidence the stakeholders place in the value of the natural flow regime as a measure of ecosystem benefit in the absence of fundamental scientific documentation. Stakeholders desired proof of ecological benefits commensurate with the certainty of economic losses. We also gained insight into the processes of integrating science

The impact of channel path length on PEMFC flow-field design

Energy Technology Data Exchange (ETDEWEB)

Shimpalee, S.; Greenway, S.; Van Zee, J.W. [Chemical Engineering Department, University of South Carolina, Columbia, SC 29208 (United States)

2006-09-29

Distributions in reactant species concentration in a PEMFC due to local consumption of fuel and local transport of water through the membrane cause distributions in current density, temperature, and water concentration in three dimensions in a PEMFC. These distributions can lead to flooding or drying of the membrane that may shorten the life of an MEA. Changing the cell's flow-field pattern to distribute the gas more evenly is one method of minimizing these stresses. This paper investigates how 200cm{sup 2} serpentine flow-fields with different number of gas paths, and thus different gas path lengths, affect performance and species distribution. The results show how the local temperature, water content, and current density distributions become more uniform for serpentine flow-field designs with shorter path lengths or larger number of channels. These results may be used to develop universal heuristics and dimensionless number correlations in the design of flow-fields and stacks. (author)

High-quality asynchronous heralded single-photon source at telecom wavelength

International Nuclear Information System (INIS)

Fasel, Sylvain; Alibart, Olivier; Tanzilli, Sebastien; Baldi, Pascal; Beveratos, Alexios; Gisin, Nicolas; Zbinden, Hugo

2004-01-01

We report on the experimental realization and characterization of an asynchronous heralded single-photon source based on spontaneous parametric down-conversion. Photons at 1550 nm are heralded as being inside a single-mode fibre with more than 60% probability, and the multi-photon emission probability is reduced by a factor of up to more than 500 compared to Poissonian light sources. These figures of merit, together with the choice of telecom wavelength for the heralded photons, are compatible with practical applications needing very efficient and robust single-photon sources

Engineering analysis of mass flow rate for turbine system control and design

International Nuclear Information System (INIS)

Yoo, Yong H.; Suh, Kune Y.

2011-01-01

Highlights: → A computer code is written to predict the steam mass flow rate through valves. → A test device is built to study the steam flow characteristics in the control valve. → Mass flow based methodology eases the programming and experimental procedures. → The methodology helps express the characteristics of each device of a turbine system. → The results can commercially be used for design and operation of the turbine system. - Abstract: The mass flow rate is determined in the steam turbine system by the area formed between the stem disk and the seat of the control valve. For precise control the steam mass flow rate should be known given the stem lift. However, since the thermal hydraulic characteristics of steam coming from the generator or boiler are changed going through each device, it is hard to accurately predict the steam mass flow rate. Thus, to precisely determine the steam mass flow rate, a methodology and theory are developed in designing the turbine system manufactured for the nuclear and fossil power plants. From the steam generator or boiler to the first bunch of turbine blades, the steam passes by a stop valve, a control valve and the first nozzle, each of which is connected with piping. The corresponding steam mass flow rate can ultimately be computed if the thermal and hydraulic conditions are defined at the stop valve, control valve and pipes. The steam properties at the inlet of each device are changed at its outlet due to geometry. The Compressed Adiabatic Massflow Analysis (CAMA) computer code is written to predict the steam mass flow rate through valves. The Valve Engineered Layout Operation (VELO) test device is built to experimentally study the flow characteristics of steam flowing inside the control valve with the CAMA input data. The Widows' Creek type control valve was selected as reference. CAMA is expected to be commercially utilized to accurately design and operate the turbine system for fossil as well as nuclear power

Comparing Face-To-Face and Asynchronous Online Communication as Mechanisms for Critical Reflective Dialogue

Science.gov (United States)

Salter, Susan; Douglas, Tracy; Kember, David

2017-01-01

Two mechanisms for engaging in critical reflective dialogue are discussed and compared: face-to-face meetings and asynchronous online discussion. The context is an umbrella action research project, with over 20 participants, which aimed to improve practices in online teaching and contribute to the development of graduate attributes. The article…

A Comparison of Asynchronous Online Text-Based Lectures and Synchronous Interactive Web Conferencing Lectures

Science.gov (United States)

Skylar, Ashley Ann

2009-01-01

Online learning environments are more prevalent in teacher education than ever before. In 2009, many instructors are attempting to emulate traditional instructional methods in the online learning environment as much as possible. Online courses are separated into two categories, (1) asynchronous; and (2) synchronous, depending on the nature of the…

Asynchronous Knowledge Sharing and Conversation Interaction Impact on Grade in an Online Business Course

Science.gov (United States)

Strang, Kenneth David

2011-01-01

Student knowledge sharing and conversation theory interactions were coded from asynchronous discussion forums to measure the effect of learning-oriented utterances on academic performance. The sample was 3 terms of an online business course (in an accredited MBA program) at a U.S.-based university. Correlation, stepwise regression, and multiple…

Design and Optimization of Annular Flow Electromagnetic Measurement System for Drilling Engineering

Directory of Open Access Journals (Sweden)

Liang Ge

2018-01-01

Full Text Available Using the downhole annular flow measurement system to get real-time information of downhole annular flow is the core and foundation of downhole microflux control drilling technology. The research work of electromagnetic flowmeter in recent years creates a challenge to the design of downhole annular flow measurement. This paper proposes a design and optimization of annular flow electromagnetic measurement system for drilling engineering based on the finite element method. Firstly, the annular flow measuring and optimization principle are described. Secondly, a simulation model of an annular flow electromagnetic measurement system with two pairs of coil is built based on the fundamental equation of electromagnetic flowmeter by COMSOL. Thirdly, simulations of the structure of excitation system of the measurement system are carried out, and simulations of the size of the electrode’s radius are also carried out based on the optimized structure, and then all the simulation results are analyzed to evaluate the optimization effect based on the evaluation indexes. The simulation results show that optimized shapes of the excitation system and electrode size can yield a better performance in the annular flow measurement.

Induction motor for superconducting synchronous/asynchronous motor

International Nuclear Information System (INIS)

Litz, D.C.; Haller, H.E. III.

1975-01-01

An induction motor structure for use on the outside of a superconducting rotor comprising a cylindrical shell of solid and laminated, magnetic iron with squirrel cage windings embedded in the outer circumference of said shell is described. The sections of the shell between the superconducting windings of the rotor are solid magnetic iron. The sections of the shell over the superconducting windings are made of laminations of magnetic iron. These laminations are parallel to the axis of the machine and are divided in halves with the laminations in each half oriented in diagonal opposition so that the intersection of the laminations forms a V. This structure presents a relatively high reluctance to leakage flux from the superconducting windings in the synchronous operating mode, while presenting a low reluctance path to the stator flux during asynchronous operation

Preliminary Axial Flow Turbine Design and Off-Design Performance Analysis Methods for Rotary Wing Aircraft Engines. Part 1; Validation

Science.gov (United States)

Chen, Shu-cheng, S.

2009-01-01

For the preliminary design and the off-design performance analysis of axial flow turbines, a pair of intermediate level-of-fidelity computer codes, TD2-2 (design; reference 1) and AXOD (off-design; reference 2), are being evaluated for use in turbine design and performance prediction of the modern high performance aircraft engines. TD2-2 employs a streamline curvature method for design, while AXOD approaches the flow analysis with an equal radius-height domain decomposition strategy. Both methods resolve only the flows in the annulus region while modeling the impact introduced by the blade rows. The mathematical formulations and derivations involved in both methods are documented in references 3, 4 for TD2-2) and in reference 5 (for AXOD). The focus of this paper is to discuss the fundamental issues of applicability and compatibility of the two codes as a pair of companion pieces, to perform preliminary design and off-design analysis for modern aircraft engine turbines. Two validation cases for the design and the off-design prediction using TD2-2 and AXOD conducted on two existing high efficiency turbines, developed and tested in the NASA/GE Energy Efficient Engine (GE-E3) Program, the High Pressure Turbine (HPT; two stages, air cooled) and the Low Pressure Turbine (LPT; five stages, un-cooled), are provided in support of the analysis and discussion presented in this paper.

Determining sociability, social space, and social presence in (A)synchronous collaborative groups

OpenAIRE

Kreijns, K.; Kirschner, P.A.; Jochems, W.; Buuren, H. van

2004-01-01

The effectiveness of group learning in asynchronous distributed learning groups depends on the social interaction that takes place. This social interaction affects both cognitive and socioemotional processes that take place during learning, group forming, establishment of group structures, and group dynamics. Though now known to be important, this aspect is often ignored, denied or forgotten by educators and researchers who tend to concentrate on cognitive processes and on-task contexts. This...

A BMI-based occupational therapy assist suit: asynchronous control by SSVEP

Directory of Open Access Journals (Sweden)

Takeshi eSakurada

2013-09-01

Full Text Available A brain-machine interface (BMI is an interface technology that uses neurophysiological signals from the brain to control external machines. Recent invasive BMI technologies have succeeded in the asynchronous control of robot arms for a useful series of actions, such as reaching and grasping. In this study, we developed non-invasive BMI technologies aiming to make such useful movements using the subject's own hands by preparing a BMI-based occupational therapy assist suit (BOTAS. We prepared a pre-recorded series of useful actionsa grasping-a-ball movement and a carrying-the-ball movementand added asynchronous control using steady-state visual evoked potential (SSVEP signals. A SSVEP signal was used to trigger the grasping-a-ball movement and another SSVEP signal was used to trigger the carrying-the-ball movement. A support vector machine was used to classify EEG signals recorded from the visual cortex (Oz in real time. Untrained, able-bodied participants (n = 12 operated the system successfully. Classification accuracy and time required for SSVEP detection were approximately 88% and 3 s, respectively. We further recruited three patients with upper cervical spinal cord injuries; they also succeeded in operating the system without training. These data suggest that our BOTAS system is potentially useful in terms of rehabilitation of patients with upper limb disabilities.

Hand-Rim Forces and Gross Mechanical Efficiency in Asynchronous and Synchronous Wheelchair Propulsion : A Comparison

NARCIS (Netherlands)

Lenton, J. P.; Fowler, N.; Nicholson, G.; Tolfrey, K.; Goosey-Tolfrey, V.; van der Woude, Lucas

To compare the force application characteristics at various push frequencies of asynchronous (ASY) and synchronous (SYN) hand-rim propulsion, 8 able-bodied participants performed a separate sub-maximal exercise test on a wheelchair roller ergometer for each propulsion mode. Each test consisted of a

Solvent effect on the degree of (a)synchronicity in polar Diels-Alder reactions from the perspective of the reaction force constant analysis.

Science.gov (United States)

Yepes, Diana; Martínez-Araya, Jorge I; Jaque, Pablo

2017-12-29

In this work, we computationally evaluated the influence of six different molecular solvents, described as a polarizable continuum model at the M06-2X/6-31+G(d,p) level, on the activation barrier/reaction rate, overall energy change, TS geometry, and degree of (a)synchronicity of two concerted Diels-Alder cycloadditions of acrolein (R1) and its complex with Lewis acid acrolein···BH 3 (R2) to cyclopentadiene. In gas-phase, we found that both exothermicity and activation barrier are only reduced by about 2.0 kcal mol -1 , and the asynchronicity character of the mechanism is accentuated when BH 3 is included. An increment in the solvent's polarity lowers the activation energy of R1 by 1.3 kcal mol -1 , while for R2 the reaction rate is enhanced by more than 2000 times at room temperature (i.e., the activation energy decreases by 4.5 kcal mol -1 ) if the highest polar media is employed. Therefore, a synergistic effect is achieved when both external agents, i.e., Lewis acid catalyst and polar solvent, are included together. This effect was ascribed to the ability of the solvent to favor the encounter between cyclopentadiene and acrolein···BH 3 . This was validated by the asymmetry of the TS which becomes highly pronounced when either both or just BH 3 is considered or the solvent's polarity is increased. Finally, the reaction force constant κ(ξ) reveals that an increment in the solvent's polarity is able to turn a moderate asynchronous mechanism of the formation of the new C-C σ-bonds into a highly asynchronous one. Graphical abstract A synergistic effect is achieved when both external agents, i.e., Lewis acid catalyst and polar solvent, are included together: lowered energy barriers and increased asynchronicities.

Learner Perceptions of Asynchronous Oral Computer-mediated Communication: Proficiency and Second Langauge Selves

Directory of Open Access Journals (Sweden)

Jesse Gleason

2012-06-01

Full Text Available Abstract The present study addresses the perceptions of international teaching assistants regarding the role of language learning tasks using Wimba Voice (WV in aiding the improvement of their second language (L2 oral skills. It specifically examines how this asynchronous computer-mediated communication (CMC technology can foster the development of these learners’ L2 selves. According to Dörnyei (2009, the more clearly learners can envision their future L2 selves, the more motivated they will be to achieve their L2 goals. With increased planning of oral production, access to instructor and peer feedback, and additional opportunities for self-reflection, asynchronous CMC technologies have been found to enable L2 learners to express their thoughts at their own pace and feel more relaxed and confident than in more threatening face-to-face situations (Sun, 2009. The findings suggest that learners have a variety of opinions regarding the role of asynchronous WV tasks in motivating them to develop their L2 oral proficiency. Also, many may prefer oral CMC environments that facilitate interaction and meaning negotiation. Results were inconclusive concerning the effect of WV-based tasks on students' perceptions of their future L2 selves; however, this may have been due to the short time frame in which these activities were employed. Résumé Nous étudions ici les perceptions d’un groupe d’assistants internationaux sur le rôle des tâches d’apprentissage linguistique à l’aide de Wimba Voice (WV. Le projet avait pour but d’améliorer les compétences orales des participants dans leur langue seconde. La présente étude examine en particulier la voie par laquelle cette technologie de la communication asynchrone par ordinateur peut favoriser l’évolution de la langue seconde des apprenants. Selon Dörnyei (2009, plus les apprenants peuvent envisager clairement un futur emploi de leur langue seconde, plus ils seront motivés à atteindre

Operational aspects of asynchronous filtering for flood forecasting

Science.gov (United States)

Rakovec, O.; Weerts, A. H.; Sumihar, J.; Uijlenhoet, R.

2015-06-01

This study investigates the suitability of the asynchronous ensemble Kalman filter (AEnKF) and a partitioned updating scheme for hydrological forecasting. The AEnKF requires forward integration of the model for the analysis and enables assimilation of current and past observations simultaneously at a single analysis step. The results of discharge assimilation into a grid-based hydrological model (using a soil moisture error model) for the Upper Ourthe catchment in the Belgian Ardennes show that including past predictions and observations in the data assimilation method improves the model forecasts. Additionally, we show that elimination of the strongly non-linear relation between the soil moisture storage and assimilated discharge observations from the model update becomes beneficial for improved operational forecasting, which is evaluated using several validation measures.

Operational aspects of asynchronous filtering for hydrological forecasting

Science.gov (United States)

Rakovec, O.; Weerts, A. H.; Sumihar, J.; Uijlenhoet, R.

2015-03-01

This study investigates the suitability of the Asynchronous Ensemble Kalman Filter (AEnKF) and a partitioned updating scheme for hydrological forecasting. The AEnKF requires forward integration of the model for the analysis and enables assimilation of current and past observations simultaneously at a single analysis step. The results of discharge assimilation into a grid-based hydrological model for the Upper Ourthe catchment in the Belgian Ardennes show that including past predictions and observations in the data assimilation method improves the model forecasts. Additionally, we show that elimination of the strongly non-linear relation between the soil moisture storage and assimilated discharge observations from the model update becomes beneficial for improved operational forecasting, which is evaluated using several validation measures.

Computer-Aided Test Flow in Core-Based Design

NARCIS (Netherlands)

Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

2000-01-01

This paper copes with the efficient test-pattern generation in a core-based design. A consistent Computer-Aided Test (CAT) flow is proposed based on the required core-test strategy. It generates a test-pattern set for the embedded cores with high fault coverage and low DfT area overhead. The CAT

Investigation on intermolecular interaction between berberine and β-cyclodextrin by 2D UV-Vis asynchronous spectra.

Science.gov (United States)

He, Anqi; Kang, Xiaoyan; Xu, Yizhuang; Noda, Isao; Ozaki, Yukihiro; Wu, Jinguang

2017-10-05

The interaction between berberine chloride and β-cyclodextrin (β-CyD) is investigated via 2D asynchronous UV-Vis spectrum. The occurrence of cross peaks around (420nm, 420nm) in 2D asynchronous spectrum reveals that specific intermolecular interaction indeed exists between berberine chloride and β-CyD. In spite of the difficulty caused by overlapping of cross peaks, we manage to confirm that the 420nm band of berberine undergoes a red-shift, and its bandwidth decreases under the interaction with β-CyD. The red-shift of the 420nm band that can be assigned to n-π* transition indicates the environment of berberine becomes more hydrophobic. The above spectral behavior is helpful in understanding why the solubility of berberine is enhanced by β-CyD. Copyright © 2017. Published by Elsevier B.V.

Automated high-throughput flow-through real-time diagnostic system

Science.gov (United States)

Regan, John Frederick

2012-10-30

An automated real-time flow-through system capable of processing multiple samples in an asynchronous, simultaneous, and parallel fashion for nucleic acid extraction and purification, followed by assay assembly, genetic amplification, multiplex detection, analysis, and decontamination. The system is able to hold and access an unlimited number of fluorescent reagents that may be used to screen samples for the presence of specific sequences. The apparatus works by associating extracted and purified sample with a series of reagent plugs that have been formed in a flow channel and delivered to a flow-through real-time amplification detector that has a multiplicity of optical windows, to which the sample-reagent plugs are placed in an operative position. The diagnostic apparatus includes sample multi-position valves, a master sample multi-position valve, a master reagent multi-position valve, reagent multi-position valves, and an optical amplification/detection system.

Flow analysis for efficient design of wavy structured microchannel mixing devices

Science.gov (United States)

Kanchan, Mithun; Maniyeri, Ranjith

2018-04-01

Microfluidics is a rapidly growing field of applied research which is strongly driven by demands of bio-technology and medical innovation. Lab-on-chip (LOC) is one such application which deals with integrating bio-laboratory on micro-channel based single fluidic chip. Since fluid flow in such devices is restricted to laminar regime, designing an efficient passive modulator to induce chaotic mixing for such diffusion based flow is a major challenge. In the present work two-dimensional numerical simulation of viscous incompressible flow is carried out using immersed boundary method (IBM) to obtain an efficient design for wavy structured micro-channel mixing devices. The continuity and Navier-Stokes equations governing the flow are solved by fractional step based finite volume method on a staggered Cartesian grid system. IBM uses Eulerian co-ordinates to describe fluid flow and Lagrangian co-ordinates to describe solid boundary. Dirac delta function is used to couple both these co-ordinate variables. A tether forcing term is used to impose the no-slip boundary condition on the wavy structure and fluid interface. Fluid flow analysis by varying Reynolds number is carried out for four wavy structure models and one straight line model. By analyzing fluid accumulation zones and flow velocities, it can be concluded that straight line structure performs better mixing for low Reynolds number and Model 2 for higher Reynolds number. Thus wavy structures can be incorporated in micro-channels to improve mixing efficiency.

PRELIMINARY DESIGN OF OSCILLATORY FLOW BIODIESEL REACTOR FOR CONTINUOUS BIODIESEL PRODUCTION FROM JATROPHA TRIGLYCERIDES

Directory of Open Access Journals (Sweden)

AZHARI T. I. MOHD. GHAZI

2008-08-01

Full Text Available The concept of a continuous process in producing biodiesel from jatropha oil by using an Oscillatory Flow Biodiesel Reactor (OFBR is discussed in this paper. It has been recognized that the batch stirred reactor is a primary mode used in the synthesis of biodiesel. However, pulsatile flow has been extensively researcehed and the fundamental principles have been successfully developed upon which its hydrodynamics are based. Oscillatory flow biodiesel reactor offers precise control of mixing by means of the baffle geometry and pulsation which facilitates to continuous operation, giving plug flow residence time distribution with high turbulence and enhanced mass and heat transfer. In conjunction with the concept of reactor design, parameters such as reactor dimensions, the hydrodynamic studies and physical properties of reactants must be considered prior to the design work initiated recently. The OFBR reactor design involves the use of simulation software, ASPEN PLUS and the reactor design fundamentals. Following this, the design parameters shall be applied in fabricating the OFBR for laboratory scale biodiesel production.

Study on the Implications of Asynchronous GMO Approvals for EU Imports of Animal Feed Products

NARCIS (Netherlands)

Nowicki, P.L.; Aramyan, L.H.; Baltussen, W.H.M.; Dvortsin, L.; Jongeneel, R.A.; Perez Dominguez, I.; Wagenberg, van C.P.A.; Kalaitzandonakes, N.; Kaufman, J.; Miller, D.; Franke, L.; Meerbeek, B.

2010-01-01

The aim of this study is to understand the implications of asynchronous approvals for genetically modified organisms (GMOs) that are imported to the European Union for use within animal feed products, specifically with regard to the EU livestock sector, as well as upon the upstream and downstream

ANALYTICAL CALCULATION OF THE BASIC ELECTROMAGNETIC LOSSES OF THE ENERGY OF THE FREQUENCY-REGULATED ASYNCHRONOUS ENGINE IN POSITIONING

Directory of Open Access Journals (Sweden)

V. O. Volkov

2018-02-01

Full Text Available Purpose. Obtaining analytical dependencies for the calculation of the main electromagnetic energy losses of a frequency-controlled induction motor in positioning modes with small displacements for various types (linear, parabolic and quasi-optimal of its velocity variation. Methodology. Similarity methods, differential and integral calculus, analytical interpolation, mathematical analysis. Findings. Analytical dependencies for calculation of current electromagnetic power losses and basic electromagnetic energy losses of a frequency-controlled asynchronous motor in the modes of positioning with small displacements for various types (linear, parabolic and quasi-optimal of its velocity are obtained. A universal form of the analytical dependence for calculating the optimal acceleration and deceleration times for a frequency-controlled asynchronous motor for positioning with small displacements, corresponding to minimization of the main electromagnetic energy losses of this engine with the indicated positioning for various species (linear, parabolic and quasi-optimal, is obtained. A comparative quantitative assessment of the change is made: the optimum values of the main electromagnetic energy losses of the frequency-controlled asynchronous engine and the corresponding maximum speed and optimal acceleration and deceleration times, in the function of the set prescribed small displacements for the various engine speed trajectories under consideration. Originality. For the first time, analytical dependencies for the calculation of the main electromagnetic energy losses of a frequency-controlled asynchronous motor are obtained for positioning with small displacements as a function of the set values of the movement of the motor shaft and the set values of its acceleration and deceleration times for the specified specified displacements. For the first time, dependences are obtained for a quantitative estimate of the minimum fundamental electromagnetic

Design and aerodynamic performance evaluation of a high-work mixed flow turbine stage

Science.gov (United States)

Neri, Remo N.; Elliott, Thomas J.; Marsh, David N.; Civinskas, Kestutis C.

1994-01-01

As axial and radial turbine designs have been pushed to their aerothermodynamic and mechanical limits, the mixed-flow turbine (MFT) concept has been projected to offer performance and durability improvements, especially when ceramic materials are considered. The objective of this NASA/U.S. Army sponsored mixed-flow turbine (AMFT) program was to determine the level of performance attainable with MFT technology within the mechanical constraints of 1997 projected ceramic material properties. The MFT geometry is similar to a radial turbine, exhibiting a large radius change from inlet to exit, but differing in that the inlet flowpath is not purely radial, nor axial, but mixed; it is the inlet geometry that gives rise to the name 'mixed-flow'. The 'mixed' orientation of the turbine inlet offers several advantages over radial designs by allowing a nonzero inlet blade angle yet maintaining radial-element blades. The oblique inlet not only improves the particle-impact survivability of the design, but improves the aerodynamic performance by reducing the incidence at the blade inlet. The difficulty, however, of using mixed-flow geometry lies in the scarcity of detailed data and documented design experience. This paper reports the design of a MFT stage designed with the intent to maximize aerodynamic performance by optimizing design parameters such as stage reaction, rotor incidence, flowpath shape, blade shape, vane geometry, and airfoil counts using 2-D, 3-D inviscid, and 3-D viscous computational fluid dynamics code. The aerodynamic optimization was accomplished while maintaining mechanical integrity with respect to vibration and stress levels in the rotor. A full-scale cold-flow rig test was performed with metallic hardware fabricated to the specifications of the hot ceramic geometry to evaluate the stage performance.

XMPP for cloud computing in bioinformatics supporting discovery and invocation of asynchronous web services

Science.gov (United States)

Wagener, Johannes; Spjuth, Ola; Willighagen, Egon L; Wikberg, Jarl ES

2009-01-01

Background Life sciences make heavily use of the web for both data provision and analysis. However, the increasing amount of available data and the diversity of analysis tools call for machine accessible interfaces in order to be effective. HTTP-based Web service technologies, like the Simple Object Access Protocol (SOAP) and REpresentational State Transfer (REST) services, are today the most common technologies for this in bioinformatics. However, these methods have severe drawbacks, including lack of discoverability, and the inability for services to send status notifications. Several complementary workarounds have been proposed, but the results are ad-hoc solutions of varying quality that can be difficult to use. Results We present a novel approach based on the open standard Extensible Messaging and Presence Protocol (XMPP), consisting of an extension (IO Data) to comprise discovery, asynchronous invocation, and definition of data types in the service. That XMPP cloud services are capable of asynchronous communication implies that clients do not have to poll repetitively for status, but the service sends the results back to the client upon completion. Implementations for Bioclipse and Taverna are presented, as are various XMPP cloud services in bio- and cheminformatics. Conclusion XMPP with its extensions is a powerful protocol for cloud services that demonstrate several advantages over traditional HTTP-based Web services: 1) services are discoverable without the need of an external registry, 2) asynchronous invocation eliminates the need for ad-hoc solutions like polling, and 3) input and output types defined in the service allows for generation of clients on the fly without the need of an external semantics description. The many advantages over existing technologies make XMPP a highly interesting candidate for next generation online services in bioinformatics. PMID:19732427

XMPP for cloud computing in bioinformatics supporting discovery and invocation of asynchronous web services

Directory of Open Access Journals (Sweden)

Willighagen Egon L

2009-09-01

Full Text Available Abstract Background Life sciences make heavily use of the web for both data provision and analysis. However, the increasing amount of available data and the diversity of analysis tools call for machine accessible interfaces in order to be effective. HTTP-based Web service technologies, like the Simple Object Access Protocol (SOAP and REpresentational State Transfer (REST services, are today the most common technologies for this in bioinformatics. However, these methods have severe drawbacks, including lack of discoverability, and the inability for services to send status notifications. Several complementary workarounds have been proposed, but the results are ad-hoc solutions of varying quality that can be difficult to use. Results We present a novel approach based on the open standard Extensible Messaging and Presence Protocol (XMPP, consisting of an extension (IO Data to comprise discovery, asynchronous invocation, and definition of data types in the service. That XMPP cloud services are capable of asynchronous communication implies that clients do not have to poll repetitively for status, but the service sends the results back to the client upon completion. Implementations for Bioclipse and Taverna are presented, as are various XMPP cloud services in bio- and cheminformatics. Conclusion XMPP with its extensions is a powerful protocol for cloud services that demonstrate several advantages over traditional HTTP-based Web services: 1 services are discoverable without the need of an external registry, 2 asynchronous invocation eliminates the need for ad-hoc solutions like polling, and 3 input and output types defined in the service allows for generation of clients on the fly without the need of an external semantics description. The many advantages over existing technologies make XMPP a highly interesting candidate for next generation online services in bioinformatics.

Asynchronous Amazon forest canopy phenology indicates adaptation to both water and light availability

International Nuclear Information System (INIS)

Jones, Matthew O; Kimball, John S; Nemani, Ramakrishna R

2014-01-01

Amazon forests represent nearly half of all tropical vegetation biomass and, through photosynthesis and respiration, annually process more than twice the amount of estimated carbon (CO 2 ) from fossil fuel emissions. Yet the seasonality of Amazon canopy cover, and the extent to which seasonal fluctuations in water availability and photosynthetically available radiation influence these processes, is still poorly understood. Implementing six remotely sensed data sets spanning nine years (2003–2011), with reported field and flux tower data, we show that southern equatorial Amazon forests exhibit a distinctive seasonal signal. Seasonal timing of water availability, canopy biomass growth and net leaf flush are asynchronous in regions with short dry seasons and become more synchronous across a west-to-east longitudinal moisture gradient of increasing dry season. Forest cover is responsive to seasonal disparities in both water and solar radiation availability, temporally adjusting net leaf flush to maximize use of these generally abundant resources, while reducing drought susceptibility. An accurate characterization of this asynchronous behavior allows for improved understanding of canopy phenology across contiguous tropical forests and their sensitivity to climate variability and drought. (letter)

Asynchronous web-based learning, a practical method to enhance teaching in emergency medicine.

Science.gov (United States)

Pourmand, Ali; Lucas, Raymond; Nouraie, Mehdi

2013-03-01

Abstract Objective: To compare medical knowledge acquisition among emergency medicine (EM) residents who attend weekly core content lectures with those absent but asynchronously viewing the same lectures in a Web-based electronic platform. During the study period all EM residents attending or absent from weekly educational conferences were given a quiz on the covered material. During Phase 1, absentees were not given supplemental educational content for missed lectures. During Phase 2, absentees were sent a link to an online multimedia module containing an audiovisual recording of the actual missed lecture with presentation slides. Scores between attendees and absentees during both phases were compared using a repeated-measures analysis to evaluate the effect of the supplemental online module on knowledge acquisition. Thirty-nine EM residents (equally distributed in postgraduate years 1-4) were studied during a 15-week period. Overall and after adjusting for sex and postgraduate year level, both lecture attendance (b=27; 95% confidence interval, 22-32; pcontent lectures. The percentage of curriculum delivery by asynchronous learning that may be used to achieve overall terminal learning objectives in medical knowledge acquisition requires further study.

Design, development and use of the finite element machine

Science.gov (United States)

Adams, L. M.; Voigt, R. C.

1983-01-01

Some of the considerations that went into the design of the Finite Element Machine, a research asynchronous parallel computer are described. The present status of the system is also discussed along with some indication of the type of results that were obtained.

The probability estimate of the defects of the asynchronous motors based on the complex method of diagnostics

Science.gov (United States)

Zhukovskiy, Yu L.; Korolev, N. A.; Babanova, I. S.; Boikov, A. V.

2017-10-01

This article is devoted to the development of a method for probability estimate of failure of an asynchronous motor as a part of electric drive with a frequency converter. The proposed method is based on a comprehensive method of diagnostics of vibration and electrical characteristics that take into account the quality of the supply network and the operating conditions. The developed diagnostic system allows to increase the accuracy and quality of diagnoses by determining the probability of failure-free operation of the electromechanical equipment, when the parameters deviate from the norm. This system uses an artificial neural networks (ANNs). The results of the system for estimator the technical condition are probability diagrams of the technical state and quantitative evaluation of the defects of the asynchronous motor and its components.

Considerations on the design of a helium circulator for a high temperature modular reactor system

International Nuclear Information System (INIS)

Dumm, K.; Donaldson, J.

1988-01-01

A modular helium cooled, high temperature reactor system with a thermal output of 200 MW per reactor has been developed by the KWU group for cogeneration of electricity and process steam. The flow of the reactor coolant - Helium at 60 bars and 250/700 deg. C is maintained by one circulator per reactor. The circulator is driven by a variable speed Siemens asynchronous motor and is submerged in the helium primary system. For operational reasons high reliability and availability of the circulator is required. The operational requirements for the circulator design are presented in this paper. The actual design has been carried out in close cooperation with the designer and manufacturer of all submerged circulators operating in AGR plants in Great Britain, James Howden Co. Renfrew, Scotland. Design solutions received so far and mainly based on sufficiently proven components - such as oil bath lubricated bearing systems - will be described. Special attention will be paid on the necessary test work; especially for the prototype to confirm the lay out. (author). 9 figs

Design of a high-lift experiment in water including active flow control

International Nuclear Information System (INIS)

Beutel, T; Schwerter, M; Büttgenbach, S; Leester-Schädel, M; Sattler, S; El Sayed, Y; Radespiel, R; Zander, M; Sinapius, M; Wierach, P

2014-01-01

This paper describes the structural design of an active flow-control experiment. The aim of the experiment is to investigate the increase in efficiency of an internally blown Coanda flap using unsteady blowing. The system uses tailor-made microelectromechanical (MEMS) pressure sensors to determine the state of the oncoming flow and an actuated lip to regulate the mass flow and velocity of a stream near a wall over the internally blown flap. Sensors and actuators are integrated into a highly loaded system that is extremely compact. The sensors are connected to a bus system that feeds the data into a real-time control system. The piezoelectric actuators using the d 33 effect at a comparable low voltage of 120 V are integrated into a lip that controls the blowout slot height. The system is designed for closed-loop control that efficiently avoids flow separation on the Coanda flap. The setup is designed for water-tunnel experiments in order to reduce the free-stream velocity and the system’s control frequency by a factor of 10 compared with that in air. This paper outlines the function and verification of the system’s main components and their development. (technical note)

Interaction between the Stress Phase Angle (SPA and the Oscillatory Shear Index (OSI Affects Endothelial Cell Gene Expression.

Directory of Open Access Journals (Sweden)

Ronny Amaya

Full Text Available Hemodynamic forces play an important role in the non-uniform distribution of atherosclerotic lesions. Endothelial cells are exposed simultaneously to fluid wall shear stress (WSS and solid circumferential stress (CS. Due to variations in impedance (global factors and geometric complexities (local factors in the arterial circulation a time lag arises between these two forces that can be characterized by the temporal phase angle between CS and WSS (stress phase angle-SPA. Asynchronous flows (SPA close to -180° that are most prominent in coronary arteries have been associated with localization of atherosclerosis. Reversing oscillatory flows characterized by an oscillatory shear index (OSI that is great than zero are also associated with atherosclerosis localization. In this study we examined the relationship between asynchronous flows and reversing flows in altering the expression of 37 genes relevant to atherosclerosis development. In the case of reversing oscillatory flow, we observed that the asynchronous condition upregulated 8 genes compared to synchronous hemodynamics, most of them proatherogenic. Upregulation of the pro-inflammatory transcription factor NFκB p65 was confirmed by western blot, and nuclear translocation of NFκB p65 was confirmed by immunofluorescence staining. A comparative study between non-reversing flow and reversing flow found that in the case of synchronous hemodynamics, reversing flow altered the expression of 11 genes, while in the case of asynchronous hemodynamics, reversing flow altered the expression of 17 genes. Reversing flow significantly upregulated protein expression of NFκB p65 for both synchronous and asynchronous conditions. Nuclear translocation of NFκB p65 was confirmed for synchronous and asynchronous conditions in the presence of flow reversal. These data suggest that asynchronous hemodynamics and reversing flow can elicit proatherogenic responses in endothelial cells compared to synchronous

Axiomatic Design of a Framework for the Comprehensive Optimization of Patient Flows in Hospitals

Directory of Open Access Journals (Sweden)

Gabriele Arcidiacono

2017-01-01

Full Text Available Lean Management and Six Sigma are nowadays applied not only to the manufacturing industry but also to service industry and public administration. The manifold variables affecting the Health Care system minimize the effect of a narrow Lean intervention. Therefore, this paper aims to discuss a comprehensive, system-based approach to achieve a factual holistic optimization of patient flows. This paper debates the efficacy of Lean principles applied to the optimization of patient flows and related activities, structures, and resources, developing a theoretical framework based on the principles of the Axiomatic Design. The demand for patient-oriented and efficient health services leads to use these methodologies to improve hospital processes. In the framework, patients with similar characteristics are clustered in families to achieve homogeneous flows through the value stream. An optimization checklist is outlined as the result of the mapping between Functional Requirements and Design Parameters, with the right sequence of the steps to optimize the patient flow according to the principles of Axiomatic Design. The Axiomatic Design-based top-down implementation of Health Care evidence, according to Lean principles, results in a holistic optimization of hospital patient flows, by reducing the complexity of the system.

An Integrated Approach to Preempt Cheating on Asynchronous, Objective, Online Assessments in Graduate Business Classes

Science.gov (United States)

Sullivan, Daniel P.

2016-01-01

Cheating, left untended, erodes the validity of evaluation and, ultimately, corrupts the legitimacy of a course. We profile an approach to manage, with an eye toward preempting, cheating on asynchronous, objective, online quizzes. This approach taps various technological and social solutions to academic dishonesty, integrating them into a…

[System of telesonography with synchronous teleconsultations and asynchronous telediagnoses (Togo)].

Science.gov (United States)

Adambounou, K; Farin, F; Boucher, A; Adjenou, K V; Gbeassor, M; N'dakena, K; Vincent, N; Arbeille, P

2012-01-01

Ultrasonography is an important nonirradiating diagnostic medical imaging procedure, frequently used, especially in urgent circumstances. This relatively inexpensive noninvasive examination makes it possible to diagnose disorders in various parts of the human body, by examining, for example, the abdomen and pelvis, the cardiovascular system, and the muscles and joints. Ultrasound is also an operator-dependent examination, in that the quality of the result depends on precision in the manipulation of the probe. Unfortunately, many small medical centers and isolated sites do not have an appropriate well-trained sonographer to perform initial evaluations, and an untrained operator cannot capture the appropriate echographic views required for a safe diagnosis of current patients, even with realtime vocal guidance (personal data). The lack of experienced physicians or qualified technicians means that diagnostic ultrasound is not always accessible to patients for rapid examination worldwide, especially in Africa, Amazonia or near the North or South Poles. This situation has led to the development of a new concept of telemedicine: telesonography, with a remote ultrasound diagnosis either in real time (synchronous) or delayed (asynchronous; store-and-forward). These systems of real-time telesonography and data transmission require expensive and complex technology with sophisticated equipment not available in many developing countries. The purpose of this study is to design a low-cost real-time system of telesonography for teleconsultations with experts and a delayed telediagnostic mode between isolated peripheral hospitals and a University Hospital center (UHC). An IP camera and an internet video server were installed in a geographically isolated site equipped with an ultrasound machine and an operator with basic training in its use. Synchronous teleconsultation (second-opinion diagnosis) is possible via internet with a UHC expert. If no ultrasound operator is available at

Fair Leader Election for Rational Agents in Asynchronous Rings and Networks

OpenAIRE

Yifrach, Assaf; Mansour, Yishay

2018-01-01

We study a game theoretic model where a coalition of processors might collude to bias the outcome of the protocol, where we assume that the processors always prefer any legitimate outcome over a non-legitimate one. We show that the problems of Fair Leader Election and Fair Coin Toss are equivalent, and focus on Fair Leader Election. Our main focus is on a directed asynchronous ring of $n$ processors, where we investigate the protocol proposed by Abraham et al. \\cite{abraham2013distributed} an...

Systematic study of packaging designs on the performance of CMOS thermoresistive micro calorimetric flow sensors

International Nuclear Information System (INIS)

Xu, Wei; Gao, Bo; Xu, Kun; Lee, Yi-Kuen; Pan, Liang; Chiu, Yi

2017-01-01

We systematically study the effect of two packaging configurations for the CMOS thermoresistive micro calorimetric flow (TMCF) sensors: S-type with the sensor chip protrusion-mounted on the flow channel wall and E-type with the sensor chip flush-mounted on the flow channel wall. Although the experimental results indicated that the sensitivity of the S-type was increased by more than 30%; the corresponding flow range as compared to the E-type was dramatically reduced by 60% from 0–11 m s −1 to 0–4.5 m s −1 . Comprehensive 2D CFD simulation and in-house developed 3D numerical simulations based on the gas-kinetic scheme were applied to study the flow separation of these two packaging designs with the major parameters. Indeed, the S-type design with the large protrusion would change the local convective heat transfer of the TMCF sensor and dramatically decrease the sensors’ performance. In addition, parametric CFD simulations of the packaging designs provide inspiration to propose a novel general flow regime map (FRM), i.e. normalized protrusion d * versus reduced chip Reynolds number Re * , where the critical boundary curve for the flow separation of TMCF sensors was determined at different channel aspect ratios. The proposed FRM can be a useful guideline for the packaging design and manufacturing of different micro thermal flow sensors. (paper)

Effect of the design change of the LSSBP on core flow distribution of APR+ Reactor

International Nuclear Information System (INIS)

Kim, Kihwan; Euh, Dong-Jin; Choi, Hae-Seob; Kwon, Tae-Soon

2014-01-01

The uniform core inlet flow distribution of an Advanced Power Reactor Plus (APR+) is required to prevent the failure rate of the HIPER fuel assembly and improve the core thermal margin. KEPCO-E and C and KAERI proposed a design change of the Lower Support Structure Bottom Plate (LSSBP), since the core flow rates were intense near the outer region of the intact LSSBP in a previous study. In this study, an experiment was carried out to evaluate the effect of the design change of the LSSBP on the core flow distribution using the APR+ Core Flow and Pressure (ACOP) test facility. The results showed great improvement on the core flow distribution under a 4-pump balanced flow condition. Under the 4-pump balanced flow condition, fifteen tests were repeated using the ACOP test facility to verify the effect of the 50% blocked flow area at the outer region of the LSSBP on the core inlet flow distribution. The profiles of the core inlet mass flow rates were analyzed using ensemble averaged values, and compared with that of the intact LSSBP. The results showed great improvement for the overall core region. The change in design of the LSSBP is expected to improve the hydraulic performance of an APR+ reactor

3-D flow analyses for design of nuclear fuel spacer

Energy Technology Data Exchange (ETDEWEB)

Karouta, Z. [ABB Combustion Engineering, Windsor, CT (United States); GU, Chun-Yuan [ABB Corporate Research, Vaesteras (Sweden); Schoelin, B. [ABB Atom AB, Vaesteras (Sweden)

1995-09-01

The Computational Fluid Dynamics (CFD) code, CFDS-FLOW3D, was used to develop improved fuel designs for PWR cores. It was used primarily to understand the fluid dynamics of grid spacers, the mass transfer between subchannels caused by spacers and in the long term to develop two-phase models which enable prediction of critical heat flux in PWR fuel. A single subchannel of one grid span was modeled. In this model different spacer designs with mixing devices were analyzed. A special treatment of the boundary condition was developed making use of flow symmetry to model the mass transfer between different subchannels and minimize the size of the computational model. This reduced the computational model to a fraction of a subchannel using traditional periodic boundary conditions. The Navier-Stokes equation was solved for the liquid and the flow turbulence was modeled by k-{xi} turbulence model. The spacer and mixing device were treated as infinite thin surfaces in the model and a zero velocity condition and turbulent wall function were applied on each side of the thin surfaces. This approach simulated the swirl from the mixing devices well, but had the drawback of not predicting pressure drop accurately since the wake behind the plates and the acceleration effect of the spacers were ignored. CFDS-FLOW3D models with mixing devices were applied in the single-phase flow regime. Velocity profiles from the CFDS-FLOW3D models were compared to Laser Doppler Velocimeter measurements taken from the flow field downstream of spaces in a full scale, cold water test loop. The predicted axial and lateral velocity profiles were in good agreement with the measurements. The evaluation of the performance of different spacer devices was made by comparing the swirl ratio downstream of the grid spacers. It is planned to evaluate heat transfer coefficient downstream of the spaces, to implement two-phase flow models, and to model the superheated boundary layer on the surface of the fuel rod.

Acoustic propagation in viscous fluid with uniform flow and a novel design methodology for ultrasonic flow meter.

Science.gov (United States)

Chen, Yong; Huang, Yiyong; Chen, Xiaoqian

2013-02-01

Ultrasonic flow meter with non-invasive no-moving-parts construction has good prospective application for space on-orbit fluid gauging. In traditional pulse transit time flow meter, inconsistency of ultrasonic transducers leads to measurement error and plane wave theory, bases of transit time flow meter, is valuable only for low-frequency wave propagation in inviscid fluid and will lose feasibility when fluid viscosity is considered. In this paper, based on the hydrodynamics of viscous fluid, wave propagation with uniform flow profile is mathematically formulated and a novel solution for viscous fluid using potential theory is firstly presented. Then a novel design methodology of continuous ultrasonic flow meter is proposed, where high measurement rangeability and accuracy are guaranteed individually by solving the integral ambiguity using multi-tone wide laning strategy and the fractional phase shift using phase lock loop tracking method. A comparison with transit time ultrasonic flow meter shows the advantage of proposed methodology. In the end, parametric analysis of viscosity on wave propagation and ultrasonic flow meter is compressively investigated. Crown Copyright © 2012. Published by Elsevier B.V. All rights reserved.

Analysis of design parameters and flow characteristics of the vortex valve for SIT flow control

International Nuclear Information System (INIS)

Hwang, Young Dong; Chang, Moon Hee; Kim, Seong O.; Kim, Young In.

1997-01-01

This study was performed to provide a technical basis for the development of the vortex valve which will be adopted in Korean Advanced Reactor. The influence of nondimensional and geometrical parameters of the vortex valve were investigated by analyzing the flow field of the vortex chamber, and the performance related parameters were evaluated by utilizing of the published experimental and analytical data. Also the level transients of the stand pipe were investigated by using of the simplified analytical model. In order to obtain the more detailed information on the vortex flow field, three dimensional preliminary analyses for the vortex valve design were conducted by FLUENT code. This study were carried out by using the simplified analytical model of the vortex valve and downstream pipe. However, the detailed analysis on the integrated system of the vortex valve with the as built design data and the required operating conditions should be performed to obtain the more accurate results on the vortex valve behavior. Also the experimental study over a wide range of operating conditions to develop the correlation of the design parameters and the performance verification should be performed for the practical design and engineering applications of the vortex valve. The results of this study can be used as a basic information for the development of the vortex valve design for the SIT of Korean Advanced Reactor. (author). 12 refs., 5 tabs., 33 figs

Design of pneumatic proportional flow valve type 5/3

Science.gov (United States)

Laski, P. A.; Pietrala, D. S.; Zwierzchowski, J.; Czarnogorski, K.

2017-08-01

In this paper the 5/3-way pneumatic, proportional flow valve was designed and made. Stepper linear actuator was used to move the spool. The valve is controlled by the controlled based on a AVR microcontroller. Virtual model of the valve was created in CAD. The real element was made based on a standard 5/3-way manually actuated valve with hand lever, which was dismounted and replaced by linear stepper motor. All the elements was mounted in a specially made housing. The controller consists of microcontroller Atmega16, integrated circuit L293D, display, two potentiometers, three LEDs and six buttons. Series of research was also conducted. Simulation research were performed using CFD by the Flow Simulation addition to SolidWorks. During the experiments the valve characteristics of flow and pressure was determined.

A Flow Rate Control Approach on Off-Design Analysis of an Organic Rankine Cycle System

Directory of Open Access Journals (Sweden)

Ben-Ran Fu

2016-09-01

Full Text Available This study explored effects of off-design heat source temperature (TW,in or flow rate (mW on heat transfer characteristics and performance of an organic Rankine cycle system by controlling the flow rate of working fluid R245fa (i.e., the operation flow rate of R245fa was controlled to ensure that R245fa reached saturation liquid and vapor states at the outlets of the preheater and evaporator, respectively. The results showed that the operation flow rate of R245fa increased with TW,in or mW; higher TW,in or mW yielded better heat transfer performance of the designed preheater and required higher heat capacity of the evaporator; heat transfer characteristics of preheater and evaporator differed for off-design TW,in and mW; and net power output increased with TW,in or mW. The results further indicated that the control strategy should be different for various off-design conditions. Regarding maximum net power output, the flow rate control approach is optimal when TW,in or mW exceeds the design point, but the pressure control approach is better when TW,in or mW is lower than the design point.

Exoplanet dynamics. Asynchronous rotation of Earth-mass planets in the habitable zone of lower-mass stars.

Science.gov (United States)

Leconte, Jérémy; Wu, Hanbo; Menou, Kristen; Murray, Norman

2015-02-06

Planets in the habitable zone of lower-mass stars are often assumed to be in a state of tidally synchronized rotation, which would considerably affect their putative habitability. Although thermal tides cause Venus to rotate retrogradely, simple scaling arguments tend to attribute this peculiarity to the massive Venusian atmosphere. Using a global climate model, we show that even a relatively thin atmosphere can drive terrestrial planets' rotation away from synchronicity. We derive a more realistic atmospheric tide model that predicts four asynchronous equilibrium spin states, two being stable, when the amplitude of the thermal tide exceeds a threshold that is met for habitable Earth-like planets with a 1-bar atmosphere around stars more massive than ~0.5 to 0.7 solar mass. Thus, many recently discovered terrestrial planets could exhibit asynchronous spin-orbit rotation, even with a thin atmosphere. Copyright © 2015, American Association for the Advancement of Science.

Dense granular Flows: a conceptual design of high-power neutron source

Directory of Open Access Journals (Sweden)

Yang Lei

2017-01-01

Full Text Available A high-power neutron source system is very useful for multifunctional applications, such as material facilities for advanced nuclear power, space radiation studies, radiography and tomography. Here the idea of inclined dense granular flow is utilized and developed in a new conceptual design of a compact high-power target to produce a high-energy and high-flux neutron irradiation (the flux is up to 1015 n/cm2/s or even 1016. Comparing to the traditional solid and liquid heavy metal targets, this design has advantages in material choice, fluid stability, heat removal, etc. In this paper the natures of the granular flows in an inclined chute are investigated and preliminary experimental and numerical results are reported. Then the feasibility of this design is discussed.

Estimation of Parameters and Flow Characteristics for the Design of Sanitary Sewers in Malaysia

Directory of Open Access Journals (Sweden)

Kamran Ansari

2013-01-01

Full Text Available Determination of the flow characteristics is very important for the design of sanitary sewers in any area. In the present study these are determined in the running sewers for the two parameters; per capita flow contribution and the peak flow factor. ISCO area - velocity flow meter model 4250 is used for this purpose. The flow meter, before being used in the running sewers, is calibrated first in the Hydraulics and Hydrology Laboratory of the UTM (Universiti Teknologi Malaysia. During the study the flow meter is installed inside the manhole in 10 different phases in the months of June, August, September, and October 2005 to monitor the sewage flow running in it. Continuous data is recorded in the flow meter during the process and the recorded time varies between 47 hours 25 minutes and 128 hours 35 minutes. The rainfall data is also collected during the same time using an automatic rain gauge which recorded rainfall at every five minutes of interval. Both the parameters thus calculated are then compared with the Malaysian Standard for sewer design i.e. MS 1228:1991. The results show that higher values of these parameters are being used in the design of sanitary sewers and extensive study needs to be carried out to review these values for future use

READ-EVAL-PRINT in Parallel and Asynchronous Proof-checking

Directory of Open Access Journals (Sweden)

Makarius Wenzel

2013-07-01

Full Text Available The LCF tradition of interactive theorem proving, which was started by Milner in the 1970-ies, appears to be tied to the classic READ-EVAL-PRINT-LOOP of sequential and synchronous evaluation of prover commands. We break up this loop and retrofit the read-eval-print phases into a model of parallel and asynchronous proof processing. Thus we explain some key concepts of the Isabelle/Scala approach to prover interaction and integration, and the Isabelle/jEdit Prover IDE as front-end technology. We hope to open up the scientific discussion about non-trivial interaction models for ITP systems again, and help getting other old-school proof assistants on a similar track.

Design of a lube oil reservoir by using flow calculations

Energy Technology Data Exchange (ETDEWEB)

Rinkinen, J; Alfthan, A. [Institute of Hydraulics and Automation IHA, Tampere University of Technology, Tampere (Finland)] Suominen, J. [Institute of Energy and Process Engineering, Tampere University of Technology, Tampere (Finland); Airaksinen, A; Antila, K [R and D Engineer Safematic Oy, Muurame (Finland)

1998-12-31

The volume of usual oil reservoir for lubrication oil systems is designed by the traditional rule of thumb so that the total oil volume is theoretically changed in every 30 minutes by rated pumping capacity. This is commonly used settling time for air, water and particles to separate by gravity from the oil returning of the bearings. This leads to rather big volumes of lube oil reservoirs, which are sometimes difficult to situate in different applications. In this presentation traditionally sized lube oil reservoir (8 m{sup 3}) is modelled in rectangular coordinates and laminar oil flow is calculated by using FLUENT software that is based on finite difference method. The results of calculation are velocity and temperature fields inside the reservoir. The velocity field is used to visualize different particle paths through the reservoir. Particles that are studied by the model are air bubbles and water droplets. The interest of the study has been to define the size of the air bubbles that are released and the size of the water droplets that are separated in the reservoir. The velocity field is also used to calculate the modelled circulating time of the oil volume which is then compared with the theoretical circulating time that is obtained from the rated pump flow. These results have been used for designing a new lube oil reservoir. This reservoir has also been modelled and optimized by the aid of flow calculations. The best shape of the designed reservoir is constructed in real size for empirical measurements. Some results of the oil flow measurements are shown. (orig.) 7 refs.

Design of a lube oil reservoir by using flow calculations

Energy Technology Data Exchange (ETDEWEB)

Rinkinen, J.; Alfthan, A. [Institute of Hydraulics and Automation IHA, Tampere University of Technology, Tampere (Finland)] Suominen, J. [Institute of Energy and Process Engineering, Tampere University of Technology, Tampere (Finland); Airaksinen, A.; Antila, K. [R and D Engineer Safematic Oy, Muurame (Finland)

1997-12-31

The volume of usual oil reservoir for lubrication oil systems is designed by the traditional rule of thumb so that the total oil volume is theoretically changed in every 30 minutes by rated pumping capacity. This is commonly used settling time for air, water and particles to separate by gravity from the oil returning of the bearings. This leads to rather big volumes of lube oil reservoirs, which are sometimes difficult to situate in different applications. In this presentation traditionally sized lube oil reservoir (8 m{sup 3}) is modelled in rectangular coordinates and laminar oil flow is calculated by using FLUENT software that is based on finite difference method. The results of calculation are velocity and temperature fields inside the reservoir. The velocity field is used to visualize different particle paths through the reservoir. Particles that are studied by the model are air bubbles and water droplets. The interest of the study has been to define the size of the air bubbles that are released and the size of the water droplets that are separated in the reservoir. The velocity field is also used to calculate the modelled circulating time of the oil volume which is then compared with the theoretical circulating time that is obtained from the rated pump flow. These results have been used for designing a new lube oil reservoir. This reservoir has also been modelled and optimized by the aid of flow calculations. The best shape of the designed reservoir is constructed in real size for empirical measurements. Some results of the oil flow measurements are shown. (orig.) 7 refs.

Student Perceptions of Asynchronous and Synchronous Web Based Tools and Perceived Attainment of Academic Outcomes

Science.gov (United States)

Parenti, Melissa A.

2013-01-01

With an increasing presence and continual adaptations related to distance learning, there is a recognized need for up-to-date research in the area of effectiveness of online education programs. More specifically, assessing the capacity to attain academic goals by use of asynchronous and synchronous web based tools within Learning Management…

Computer aided hydraulic design of axial flow pump impeller

International Nuclear Information System (INIS)

Sreedhar, B.K.; Rao, A.S.L.K.; Kumaraswamy, S.

1994-01-01

Pumps are the heart of any power plant and hence their design requires great attention. Computers with their potential for rapid computation can be successfully employed in the design and manufacture of these machines. The paper discusses a program developed for the hydraulic design of axial flow pump impeller. The program, written in FORTRAN 77, is interactive and performs the functions of design calculation, drafting and generation of numerical data for blade manufacture. The drafting function, which makes use of the software ACAD, is carried out automatically by means of suitable interface programs. In addition data for blade manufacture is also generated in either the x-y-z or r-θ-z system. (author). 4 refs., 3 figs

High engagement, high quality: A guiding framework for developing empirically informed asynchronous e-learning programs for health professional educators.

Science.gov (United States)

Sinclair, Peter M; Levett-Jones, Tracey; Morris, Amanda; Carter, Ben; Bennett, Paul N; Kable, Ashley

2017-03-01

E-learning involves the transfer of skills and knowledge via technology so that learners can access meaningful and authentic educational materials. While learner engagement is important, in the context of healthcare education, pedagogy must not be sacrificed for edu-tainment style instructional design. Consequently, health professional educators need to be competent in the use of current web-based educational technologies so that learners are able to access relevant and engaging e-learning materials without restriction. The increasing popularity of asynchronous e-learning programs developed for use outside of formal education institutions has made this need more relevant. In these contexts, educators must balance design and functionality to deliver relevant, cost-effective, sustainable, and accessible programs that overcome scheduling and geographic barriers for learners. This paper presents 10 guiding design principles and their application in the development of an e-learning program for general practice nurses focused on behavior change. Consideration of these principles will assist educators to develop high quality, pedagogically sound, engaging, and interactive e-learning resources. © 2017 John Wiley & Sons Australia, Ltd.

Real-Time Implementation of an Asynchronous Vision-Based Target Tracking System for an Unmanned Aerial Vehicle

Science.gov (United States)

2007-06-01

Chin Khoon Quek. “Vision Based Control and Target Range Estimation for Small Unmanned Aerial Vehicle.” Master’s Thesis, Naval Postgraduate School...December 2005. [6] Kwee Chye Yap. “Incorporating Target Mensuration System for Target Motion Estimation Along a Road Using Asynchronous Filter

Design of flow-field patterns for proton exchange membrane fuel cell application

International Nuclear Information System (INIS)

Rosli, M.I.; Wan Ramli Wan Daud; Kamaruzzaman Sopian; Jaafar Sahari

2006-01-01

Fuel cells are electrochemical devices that produce electricity at high efficiency without combustion. Fuel cells are emerging as viable candidates as power sources in many applications, including road vehicles, small-scale power stations, and possibly even portable electronics. This paper addresses the design of flow-field patterns for proton exchange membrane fuel cell (PEMFC). The PEMFC is a low-temperature fuel cell, in which a proton conductive polymer membrane is used as the electrolyte. In PEMFC, flow-field pattern is one important thing that effects the performance of PEMFC. This paper present three types of flow-field pattern that will be consider to be testing using CFD analysis and by experimental. The design look detail on to their shape and dimension to get the best pattern in term of more active electrode area compare to electrode area that will be used. Another advantage and disadvantage for these three type of flow-field patterns from literature also compared in this paper

An Asynchronous Many-Task Implementation of In-Situ Statistical Analysis using Legion.

Energy Technology Data Exchange (ETDEWEB)

Pebay, Philippe Pierre [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Bennett, Janine Camille [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2015-11-01

In this report, we propose a framework for the design and implementation of in-situ analy- ses using an asynchronous many-task (AMT) model, using the Legion programming model together with the MiniAero mini-application as a surrogate for full-scale parallel scientific computing applications. The bulk of this work consists of converting the Learn/Derive/Assess model which we had initially developed for parallel statistical analysis using MPI [PTBM11], from a SPMD to an AMT model. In this goal, we propose an original use of the concept of Legion logical regions as a replacement for the parallel communication schemes used for the only operation of the statistics engines that require explicit communication. We then evaluate this proposed scheme in a shared memory environment, using the Legion port of MiniAero as a proxy for a full-scale scientific application, as a means to provide input data sets of variable size for the in-situ statistical analyses in an AMT context. We demonstrate in particular that the approach has merit, and warrants further investigation, in collaboration with ongoing efforts to improve the overall parallel performance of the Legion system.

Axiomatic Design of a Framework for the Comprehensive Optimization of Patient Flows in Hospitals

Science.gov (United States)

Arcidiacono, Gabriele; Matt, Dominik T.; Rauch, Erwin

2017-01-01

Lean Management and Six Sigma are nowadays applied not only to the manufacturing industry but also to service industry and public administration. The manifold variables affecting the Health Care system minimize the effect of a narrow Lean intervention. Therefore, this paper aims to discuss a comprehensive, system-based approach to achieve a factual holistic optimization of patient flows. This paper debates the efficacy of Lean principles applied to the optimization of patient flows and related activities, structures, and resources, developing a theoretical framework based on the principles of the Axiomatic Design. The demand for patient-oriented and efficient health services leads to use these methodologies to improve hospital processes. In the framework, patients with similar characteristics are clustered in families to achieve homogeneous flows through the value stream. An optimization checklist is outlined as the result of the mapping between Functional Requirements and Design Parameters, with the right sequence of the steps to optimize the patient flow according to the principles of Axiomatic Design. The Axiomatic Design-based top-down implementation of Health Care evidence, according to Lean principles, results in a holistic optimization of hospital patient flows, by reducing the complexity of the system. © 2017 Gabriele Arcidiacono et al.

MODELING OF SYMMETRIC THREE-PHASE ASYNCHRONOUS ELECTRIC MOTOR IN ASYMMETRIC CONNECTION TO NETWORK

Directory of Open Access Journals (Sweden)

V. I. Lukovnikov

2005-01-01

Full Text Available The paper shows how to solve the problem concerning reveal of changes in mathematical models and electric parameters of symmetric three-phase short-circuited asynchronous electric motors in case of their connection to single- or two-phase network in comparison with their connection to three-phase network. The uniform methodological approach permitting to generalize the known data and receive new results is offered in the paper.

Communicating in designing an oral repository for rural African villages

CSIR Research Space (South Africa)

Reitmaier, T

2012-05-01

Full Text Available We describe designing an asynchronous, oral repository and sharing system that we intend to suit the needs and practices of rural residents in South Africa. We aim to enable users without access to personal computers to record, store, and share...

Modeling, design, fabrication and characterization of a micro Coriolis mass flow sensor

International Nuclear Information System (INIS)

Haneveld, J; Lammerink, T S J; De Boer, M J; Sanders, R G P; Mehendale, A; Lötters, J C; Dijkstra, M; Wiegerink, R J

2010-01-01

This paper discusses the modeling, design and realization of micromachined Coriolis mass flow sensors. A lumped element model is used to analyze and predict the sensor performance. The model is used to design a sensor for a flow range of 0–1.2 g h −1 with a maximum pressure drop of 1 bar. The sensor was realized using semi-circular channels just beneath the surface of a silicon wafer. The channels have thin silicon nitride walls to minimize the channel mass with respect to the mass of the moving fluid. Special comb-shaped electrodes are integrated on the channels for capacitive readout of the extremely small Coriolis displacements. The comb-shaped electrode design eliminates the need for multiple metal layers and sacrificial layer etching methods. Furthermore, it prevents squeezed film damping due to a thin layer of air between the capacitor electrodes. As a result, the sensor operates at atmospheric pressure with a quality factor in the order of 40 and does not require vacuum packaging like other micro Coriolis flow sensors. Measurement results using water, ethanol, white gas and argon are presented, showing that the sensor measures true mass flow. The measurement error is currently in the order of 1% of the full scale of 1.2 g h −1

Experimental and Numerical Design and Optimization of a Counter-Flow Heat Exchanger

Directory of Open Access Journals (Sweden)

Bahrami Salman

2018-01-01

Full Text Available A new inexpensive counter-flow heat exchanger has been designed and optimized for a vapor-compression cooling system in this research. The main aim is to experimentally and numerically evaluate the effect of an internal heat exchanger (IHX adaptation in an automotive air conditioning system. In this new design of IHX, the high-pressure liquid passes through the central channel and the low-pressure vapor flows in several parallel channels in the opposite direction. The experimental set-up has been made up of original components of the air conditioning system of a medium sedan car, specially designed and built to analyze vehicle A/C equipment under real operating conditions. The results show that this compact IHX may achieve up to 10% of the evaporator capacity while low pressure drop will be imposed on this refrigeration cycle. Also, they confirm considerable decrease of compressor power consumption (CPC, which is intensified at higher evaporator air flow. A significant improvement of the coefficient of performance (COP is achieved with the IHX employment too. The influence of operating conditions has been also discussed in this paper. Finally, numerical analyses have been briefly presented, which bring more details of the flow behavior and heat transfer phenomena, and help to determine the optimal arrangement of channels.

Experimental Study and Comparison of Various Designs of Gas Flow Fields to PEM Fuel Cells and Cell Stack Performance

International Nuclear Information System (INIS)

Liu, Hong; Li, Peiwen; Juarez-Robles, Daniel; Wang, Kai; Hernandez-Guerrero, Abel

2014-01-01

In this study, a significant number of experimental tests to proton exchange membrane (PEM) fuel cells were conducted to investigate the effect of gas flow fields on fuel cell performance. Graphite plates with various flow field or flow channel designs, from literature survey and also novel designs by the authors, were used for the PEM fuel cell assembly. The fabricated fuel cells have an effective membrane area of 23.5 cm 2 . The results showed that the serpentine flow channel design is still favorable, giving the best single fuel cell performance amongst all the studied flow channel designs. A novel symmetric serpentine flow field was proposed for a relatively large sized fuel cell application. Four fuel cell stacks each including four cells were assembled using different designs of serpentine flow channels. The output power performances of fuel cell stacks were compared and the novel symmetric serpentine flow field design is recommended for its very good performance.

DENA: A Configurable Microarchitecture and Design Flow for Biomedical DNA-Based Logic Design.

Science.gov (United States)

Beiki, Zohre; Jahanian, Ali

2017-10-01

DNA is known as the building block for storing the life codes and transferring the genetic features through the generations. However, it is found that DNA strands can be used for a new type of computation that opens fascinating horizons in computational medicine. Significant contributions are addressed on design of DNA-based logic gates for medical and computational applications but there are serious challenges for designing the medium and large-scale DNA circuits. In this paper, a new microarchitecture and corresponding design flow is proposed to facilitate the design of multistage large-scale DNA logic systems. Feasibility and efficiency of the proposed microarchitecture are evaluated by implementing a full adder and, then, its cascadability is determined by implementing a multistage 8-bit adder. Simulation results show the highlight features of the proposed design style and microarchitecture in terms of the scalability, implementation cost, and signal integrity of the DNA-based logic system compared to the traditional approaches.

Design Optimization of An Axial Flow Fan Blade Considering Airfoil Shape and Stacking Line

Energy Technology Data Exchange (ETDEWEB)

Lee, Ki Sang; Kim, Kwang Yong; Samad, Abdus [Inha Univ., Incheon (Korea, Republic of)

2007-07-01

This work presents a numerical optimization procedure for a low-speed axial flow fan blade with polynomial response surface approximation model. Reynolds-averaged Navier-Stokes equations with Shear Stress Turbulence (SST) model are discretized by finite volume approximations and solved on hexahedral grids for flow analyses. The airfoil shape as well as stacking line is modified to enhance blade total efficiency, i.e., the objective function. The design variables of blade lean, maximum thickness and location of maximum thickness are selected, and a design of experiments technique produces design points where flow analyses are performed to obtain values of the objective function. A gradient-based search algorithm is used to find the optimal design in the design space from the constructed response surface model for the objective function. As a main result, the efficiency is increased effectively by the present optimization procedure. And, it is also shown that the modification of blade lean is more effective to improve the efficiency rather than modifying blade profile.

A 0.8mW 5bit 250MS/s time-interleaved asynchronous digital slope ADC

NARCIS (Netherlands)

Harpe, P.J.A.; Zhou, C.; Philips, K.J.P.; Groot, de H.W.H.

2011-01-01

Slope and digital-ramp converters are normally limited to very low sampling rates, since they require a digital counter at a highly oversampled clock rate. In this work, an asynchronous digital slope architecture is introduced that only requires a nonoversampled clock, thus enabling a much higher

Declarative flow control for distributed instrumentation

Energy Technology Data Exchange (ETDEWEB)

Parvin, Bahram; Taylor, John; Fontenay, Gerald; Callahan, Daniel

2001-06-01

We have developed a 'microscopy channel' to advertise a unique set of on-line scientific instruments and to let users join a particular session, perform an experiment, collaborate with other users, and collect data for further analysis. The channel is a collaborative problem solving environment (CPSE) that allows for both synchronous and asynchronous collaboration, as well as flow control for enhanced scalability. The flow control is a declarative feature that enhances software functionality at the experimental scale. Our testbed includes several unique electron and optical microscopes with applications ranging from material science to cell biology. We have built a system that leverages current commercial CORBA services, Web Servers, and flow control specifications to meet diverse requirements for microscopy and experimental protocols. In this context, we have defined and enhanced Instrument Services (IS), Exchange Services (ES), Computational Services (CS), and Declarative Services (DS) that sit on top of CORBA and its enabling services (naming, trading, security, and notification) IS provides a layer of abstraction for controlling any type of microscope. ES provides a common set of utilities for information management and transaction. CS provides the analytical capabilities needed for online microscopy. DS provides mechanisms for flow control for improving the dynamic behavior of the system.

Asynchronous Amazon Forest Canopy Phenology Indicates Adaptation to Both Water and Light Availability