WorldWideScience

Sample records for anechoic testing results

  1. Tests of anechoic chamber for aeroacoustics investigations

    Science.gov (United States)

    Palchikovskiy, V. V.; Bersenev, Yu. V.; Makashov, S. Yu.; Belyaev, I. V.; Korin, I. A.; Sorokin, E. V.; Khramtsov, I. V.; Kustov, O. Yu.

    2016-10-01

    The paper presents the results of qualification tests in the new anechoic chamber of Perm National Research Polytechnic University (PNRPU) built in 2014-2015 and evaluation of the chamber quality in aeroacoustic experiments. It describes design features of the chamber and its sound-absorption lining. The qualification tests were carried out with tonal and broadband noise sources in the frequency range 100 Hz - 20 kHz for two different cases of the source arrangement. In every case, measurements were performed in three directions by traverse microphones. Qualification tests have determined that in the chamber there is a free acoustic field within radius of 2 m for tonal noise and 3 m for broadband noise. There was also evaluated acoustic quality of the chamber by measurements of the jet noise and vortex ring noise. The results of the experiments demonstrate that PNRPU anechoic chamber allows the aeroacoustic measurements to be performed to obtain quantitative results.

  2. Anechoic Radio Frequency Test Chamber

    Data.gov (United States)

    Federal Laboratory Consortium — This chamber is used for characterization test of such systems as communications gear, tanks, radar, missiles, and helicopters. The dimensions of the chamber are 114...

  3. Emulating Ray-Tracing Channels in Multi-probe Anechoic Chamber Setups for Virtual Drive Testing

    DEFF Research Database (Denmark)

    Fan, Wei; Llorente, Ines Carton; Kyösti, Pekka

    2016-01-01

    This paper discusses virtual drive testing (VDT) for multiple-input multiple-output (MIMO) capable terminals in multi-probe anechoic chamber (MPAC) setups. We propose to perform VDT, via reproducing ray tracing (RT) simulated channels with the field synthesis technique. Simulation results demonst...

  4. MIMO OTA Testing in Small Multi-Probe Anechoic Chamber Setups

    DEFF Research Database (Denmark)

    Llorente, Ines Carton; Fan, Wei; Pedersen, Gert F.

    2016-01-01

    OTA testing of MIMO capable terminals is often performed in large anechoic chambers, where planar waves impinging the test area are assumed. Furthermore, reflections from the chamber, and probe coupling are often considered negligible due to the large dimensions of the chamber. This paper...... investigates the feasibility of reducing the physical dimension of 2D multi-probe anechoic chamber setups for MIMO OTA testing, with the purpose of reducing the cost and space of the setup. In the paper, a channel emulation algorithm and chamber compensation technique are proposed for MIMO OTA testing in small...

  5. Directed Energy Anechoic Chamber

    Data.gov (United States)

    Federal Laboratory Consortium — The Directed Energy Anechoic Chamber comprises a power anechoic chamber and one transverse electromagnetic cell for characterizing radiofrequency (RF) responses of...

  6. Test Setup for Anechoic Room based MIMO OTA Testing of LTE Terminals

    DEFF Research Database (Denmark)

    Carreño, Xavier; Fan, Wei; Nielsen, Jesper Ødum;

    2013-01-01

    introduced into, for example, LTE andWiMAX systems. The main purpose of this testing is to validate that the user equipment will have a good performance in real use. CTIA, 3GPP and COST are spending a big effort in standardizing the OTA testing procedure which is much more complex than similar SISO OTA...

  7. A portable miniature anechoic chamber

    Science.gov (United States)

    Lorthioir, Jack; Gavin, Paul

    The portable miniature anechoic chamber (PMAC), a low-cost alternative to a full-size anechoic chamber, is presented. The PMAC is a miniature, enclosed, RF-tight microwave antenna range, which approximates the performance of an indoor range over the C through Ku (G through J)-band frequencies. The small footprint, four by six feet, allows for ease of movement by one person to a test site, indoors or outdoors. The PMAC can be used at I (intermediate)-level to support the operational readiness (OR) requirements of the U.S. Army, Navy or Air Force. In conjunction with the antenna test equipment (ATE), and under TPS control, it can be used for performance verification, fault detection and fault isolation. A typical application using the PMAC in this operating mode is described.

  8. The Kevlar-walled anechoic wind tunnel

    Science.gov (United States)

    Devenport, William J.; Burdisso, Ricardo A.; Borgoltz, Aurelien; Ravetta, Patricio A.; Barone, Matthew F.; Brown, Kenneth A.; Morton, Michael A.

    2013-08-01

    The aerodynamic and acoustic performance of an anechoic wind tunnel test section with walls made from thin Kevlar cloth have been measured and analyzed. The Kevlar test section offers some advantages over a conventional free-jet arrangement. The cloth contains the bulk of the flow but permits the transmission of sound with little loss. The containment results in smaller far-field aerodynamic corrections meaning that larger models can be tested at higher Reynolds numbers. The containment also eliminates the need for a jet catcher and allows for a much longer test section. Model-generated noise is thus more easily separated from facility background using beamforming. Measurements and analysis of acoustic and aerodynamic corrections for a Kevlar-walled test section are presented and discussed, along with benchmark trailing edge noise measurements.

  9. Better RCS data with anechoic absober characterization

    Science.gov (United States)

    Brumley, Steve

    1987-05-01

    An adequate understanding of the performance of the absorber material is critical in achieving optimum performance levels of compact ranges or conventional anechoic chambers. The conventional testing technique, the NLR arch method, used for the free-space testing of absorbers is first reviewed, and its flaws are examined. Consideration is then given to new measurement techniques that eliminate the problems of the NLR arch method. These are: (1) Inverse Synthetic Aperture Radar (ISAR) imaging of a large test sample wall (122x122 wavelengths at 15 GHz) of material (16 pieces of absorber material on the wall); (2) measurements with a wideband coherent radar capable of generating range-resolved diagnostic data; and (3) conventional time-gathered RCS measurements made as a function of aspect angle of the sample wall target. Results obtained for different materials are discussed.

  10. Comparison of Channel Emulation Techniques in Multiprobe Anechoic Chamber Setups

    DEFF Research Database (Denmark)

    Llorente, Ines Carton; Fan, Wei; Nielsen, Jesper Ødum;

    2015-01-01

    This paper compares two different techniques for channel emulation in multiprobe anechoic chamber based setups, which is a candidate solution for the standardization of MIMO OTA performance testing of mobile devices. The comparison is performed via simulations of the field distribution, temporal...... correlation, and spatial correlation emulated by these methods for different number of probes. Results show that the emulation accuracy of the field distribution and temporal correlation are degraded when the emulation technique uses a single sinusoid per probe antenna, while the emulation accuracy...

  11. Rician Channel Modeling for Multiprobe Anechoic Chamber Setups

    DEFF Research Database (Denmark)

    Fan, Wei; Kyösti, Pekka; Hentilä, Lassi;

    2014-01-01

    This paper discusses over the air (OTA) testing for multiple input multiple output (MIMO) capable terminals, with emphasis on modeling Rician channel models in the multi-probe anechoic chamber setups. A technique to model Rician channels is proposed. The line-of-sight (LOS) component, with an arb......This paper discusses over the air (OTA) testing for multiple input multiple output (MIMO) capable terminals, with emphasis on modeling Rician channel models in the multi-probe anechoic chamber setups. A technique to model Rician channels is proposed. The line-of-sight (LOS) component...

  12. Investigation on High Performance of 10m Semi Anechoic Chamber by using Open-Top Hollow Pyramidal Hybrid EM Wave Absorber

    Science.gov (United States)

    Kurihara, Hiroshi; Saito, Toshifumi; Suzuki, Yoshikazu; Nishikata, Atsuhiro; Hashimoto, Osamu

    The emission radiated from electric and electronic equipments is evaluated through OATS. Recently, it is not fully prepared the environment for OATS because of a variety of communication radiation sources (e.g., digital television broadcast and cellular phone station). Therefore, the EM anechoic chambers are becoming more and more important as EMI test site. On the other hand, the EM anechoic chambers are needed high performance in order to cut down EMI countermeasure cost and calculate the antenna factor. The objective of this paper is mainly to present the EM wave absorber design in order to obtain within ±2dB against the theoretical site attenuation values in the 10m semi anechoic chamber at 30MHz to 300MHz. We get the necessary reflectivity of EM wave absorber by the basic site attenuation equation. We design the open-top hollow pyramidal new hybrid EM wave absorber consisted of 180cm long dielectric loss foam and ferrite tiles. Then, we design the 10m semi anechoic chamber by using the ray-tracing simulation and construct it in the size of L24m×W15.2m×H11.2m. More over, we measure the site attenuation of the constructed 10m semi anechoic chamber by using the broadband calculable dipole antennas. As the result, we confirm the validity of the designed open-top hollow pyramidal new hybrid EM wave absorber.

  13. Acoustic analysis of a semi-anechoic chamber with intersection

    Directory of Open Access Journals (Sweden)

    P. Nassiri

    2014-05-01

    .Conclusion: According to the results, it can be concluded that the suggested intersection layout of rectangular fibrous absorbents can be used as a reliable method in order to reduce the reverberation time and to gain lower cut-off frequency for construct a semi anechoic chamber with the high efficiency.

  14. Cholesterol testing and results

    Science.gov (United States)

    Cholesterol test results; LDL test results; VLDL test results; HDL test results; Coronary risk profile results; Hyperlipidemia- ... Some cholesterol is considered good and some is considered bad. Different blood tests can be done to measure each ...

  15. NRAO RF Anechoic Chamber & Antenna Range

    Data.gov (United States)

    Federal Laboratory Consortium — A shielded anechoic chamber measuring 15 by 15 by 37 feet is located in the Jansky Laboratory at Green Bank. This chamber has been outfitted as a far-field antenna...

  16. RADAR Anechoic Chamber/RCS Measurements Lab

    Data.gov (United States)

    Federal Laboratory Consortium — The RF Anechoic Chamber is 56 feet long by 12 feet high by 13.5 feet wide, with an adjoining electronic computer control room. A double door entrance at one end of...

  17. Construction of an anechoic chamber for aeroacoustic experiments and examination of its acoustic parameters

    Science.gov (United States)

    Kopiev, V. F.; Palchikovskiy, V. V.; Belyaev, I. V.; Bersenev, Yu. V.; Makashov, S. Yu.; Khramtsov, I. V.; Korin, I. A.; Sorokin, E. V.; Kustov, O. Yu.

    2017-01-01

    The acoustic parameters of a new anechoic chamber constructed at Perm National Research Polytechnic University (PNRPU) are presented. This chamber is designed to be used, among other things, for measuring noise from aerodynamic sources. Sound-absorbing wedges lining the walls of the chamber were studied in an interferometer with normal wave incidence. The results are compared to the characteristics of sound-absorbing wedges of existing anechoic facilities. Metrological examination of the acoustic parameters of the PNRPU anechoic chamber demonstrates that free field conditions are established in it, which will make it possible to conduct quantitative acoustic experiments.

  18. Sound Insulation Test and Analysis of a V-Type Sound Barrier Based on the Method of Reverberation Room and Semi-anechoic Room%基于混响室-半消声室的V型声屏障隔声测试与分析

    Institute of Scientific and Technical Information of China (English)

    张学飞; 李晔; 王瑞乾; 吴冬; 徐磊

    2015-01-01

    首先以匀质铁板为例,利用混响室—半消声室法进行频率隔声特性的测试,并将测试结果与混响室—混响室隔声测试结果进行对比分析;然后,基于半消声室模拟半无限声场的特性,在混响室—半消声室环境下分别对V型声屏障进行表面声透射及声传播指向性识别。结果表明,混响室—半消声室法频率隔声特性测试结果与半消声室一侧的测点位置有关,当测点位置较为合适时,能够与混响室—混响室法测试结果较好的吻合;混响室—半消声室法能够识别样件的表面声透射特性及声传播指向特性,从而为找到其隔声薄弱环节以及声音透过样件后的传播和衰减规律提供更加直观的数据参考,对进一步提高其隔声性能并改善声场环境具有指导意义。%The sound insulation effect of an isotropic iron plate was measured based on the approach of reverberation room and semi-anechoic room, and the result was compared with the method based on reverberation room and reverberation room. Then, based on the semi-infinite sound field characteristics of the semi-anechoic room, the surface sound transmission and the directivity of sound propagation of a V-type sound barrier were recognized. It is concluded that the sound reduction result of the plate tested by the approach of reverberation room and semi-anechoic room is related to the position of measurement points. If the measurement points are properly distributed, the sound reduction result can agree well with that tested by the method of reverberation room and reverberation room. The test method of reverberation room and semi-anechoic room can identify the characteristics of the surface sound transmission and the directivity of sound propagation, so as to provide more visual data references to recognize the portions with lower sound insulation effect and the sound propagation and reduction laws after the sound has passed the

  19. Determination of efficiency of anechoic or decoupling hull coatings using water tank acoustic measurements

    OpenAIRE

    AUDOLY, Christian

    2012-01-01

    International audience; External anechoic and decoupling hull coatings are used on ships or submarines to reduce acoustic target strength and radiated noise, respectively. Measurement of test panels in a water tank gives only the reflection and transmission coefficients in free field, with respects to frequency. It is shown using simple models that anechoic and decoupling efficiencies can be derived, providing appropriate modulus and phase measurement of the coefficients. Additionnally, the i...

  20. On the acoustic wedge design and simulation of anechoic chamber

    Science.gov (United States)

    Jiang, Changyong; Zhang, Shangyu; Huang, Lixi

    2016-10-01

    This study proposes an alternative to the classic wedge design for anechoic chambers, which is the uniform-then-gradient, flat-wall (UGFW) structure. The working mechanisms of the proposed structure and the traditional wedge are analyzed. It is found that their absorption patterns are different. The parameters of both structures are optimized for achieving minimum absorber depth, under the condition of absorbing 99% of normal incident sound energy. It is found that, the UGFW structure achieves a smaller total depth for the cut-off frequencies ranging from 100 Hz to 250 Hz. This paper also proposes a modification for the complex source image (CSI) model for the empirical simulation of anechoic chambers, originally proposed by Bonfiglio et al. [J. Acoust. Soc. Am. 134 (1), 285-291 (2013)]. The modified CSI model considers the non-locally reactive effect of absorbers at oblique incidence, and the improvement is verified by a full, finite-element simulation of a small chamber. With the modified CSI model, the performance of both decorations with the optimized parameters in a large chamber is simulated. The simulation results are analyzed and checked against the tolerance of 1.5 dB deviation from the inverse square law, stipulated in the ISO standard 3745(2003). In terms of the total decoration depth and anechoic chamber performance, the UGFW structure is better than the classic wedge design.

  1. The Implement of Multi-Channel Noise Test System in Anechoic Chamber%消声室多通道噪声测试系统实现

    Institute of Scientific and Technical Information of China (English)

    刘维嘉

    2016-01-01

    This paper introduces the multi-channel noise test system based on virtual instrument technology. This test system uses microphones,preamplifier and sound vibration data acquisition hardware.The test sys-tem is realized by LabVIEW;it can test the sound pressure level and sound power level for machinery and oth-er machinery.And the test system with high performance,high precision,etc.,greatly improving the efficiency while significantly reducing the cost of test.%该文介绍了基于虚拟仪器技术的多通道噪声测试系统。该系统硬件采用了传声器、预放及声音振动数据采集卡,通过LabVIEW编写测试系统,实现对机器机械等噪声源的声压级和声功率级测试。该测试系统具有高性能、高精度等优点,在提高效率的同时降低了测试成本。

  2. Radio Frequency Anechoic Chamber Facility

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Supports the design, manufacture, and test of antenna systems. The facility is also used as an electromagnetic compatibility/radio frequency interference...

  3. GIRAFFE test results summary

    Energy Technology Data Exchange (ETDEWEB)

    Yokobori, S.; Arai, K.; Oikawa, H. [Toshiba Corporation, Kawasaki (Japan)

    1996-03-01

    A passive system can provide engineered safety features enhancing safety system reliability and plant simplicity. Toshiba has conducted the test Program to demonstrate the feasibility of the SBWR passive safety system using a full-height, integral system test facility GIRAFFE. The test facility GIRAFFE models the SBWR in full height to correctly present the gravity driving head forces with a 1/400 volume scale. The GIRAFFE test Program includes the certification tests of the passive containment cooling system (PCCS) to remove the post-accident decay heat and the gravity driven cooling system (GDCS) to replenish the reactor coolant inventory during a LOCA. The test results have confirmed the PCCS and GDCS design and in addition, have demonstrated the operation of the pCCS with the presence of a lighter-than-steam noncondensable as well as with the presence of a heavier-than-steam, noncondensable. The GIRAFFE test Program has also provided the database to qualify a best estimate thermal-hydraulic computer code TRAC. The post test analysis results have shown that TRAC can accurately predict the PCCS heat removal Performance and the containment pressure response to a LOCA. This paper summarizes the GIRAFFE test results to investigate post-LOCA PCCS heat removal performance and post-test analysis using TRAC.

  4. Ibis DDT test results

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This document contains test results from a study done to determine the organochlorine levels in the livers of white-faced ibis from Stillwater Wildlife Management...

  5. The New Anechoic Shielded Chambers Designed for Space and Commercial Applications at LIT

    Science.gov (United States)

    da Silva, Benjamim; Galvao, M. C.; Pereira, Clovis Solano

    2008-01-01

    The main objective of this paper is to present the capabilities of the new anechoic shielded rooms designed for space and commercial applications as part of the Integration and Testing Laboratory (LIT, Laboratorio de Integracao e Testes) in Brazil. A new anechoic shielded room named CBA2 has been in full operation since March 2007 and a remodeled chamber CBA1 is planned to be ready by the end of 2008, replacing an old facility which was in operation for the last 18 years. The Brazilian Space Program started with very small and simple satellites and the old CBA1 chamber was conceived in 1987 to accomplish the EMI/EMC tests not requiring significant volumes. Since the very beginning this facility was also used by the private sector for other applications mainly due to the absorption of digital electronics in all kind of products. The intense use of this facility during the last years, operating three shifts a day, caused a normal degradation and imposed several limitations. Therefore, a new totally remodeled chamber was designed considering the state of the art in terms of absorbers and associated instrumentation. On the other hand the facility CBA2 was conceived, designed and implemented to test large satellites taking into account the advance of the technology in terms of RF frequencies, power level, testing methodologies and several other factors. A very interesting and unique aspect of this project was the partnership between the private sector and governmental institution. As a result, the total investment was shared between several companies and consequently a time-sharing use of the facility as well.

  6. Anechoic chamber in industrial plants. [construction materials and structural design

    Science.gov (United States)

    Halpert, E.; Juncu, O.; Lorian, R.; Marfievici, D.; Mararu, I.

    1974-01-01

    A light anechoic chamber for routine acoustical measurements in the machine building industry is reported. The outer housing of the chamber consists of modules cast in glass fiber reinforced polyester resin; the inner housing consists of pyramidal modules cut out of sound absorbing slates. The parameters of this anechoic chamber facilitate acoustical measurements according to ISO and CAEM recommendations.

  7. Simulation of flight-type engine fan noise in the NASA-Lewis 9 x 15 anechoic wind tunnel

    Science.gov (United States)

    Heidmann, M. F.; Dietrich, D. A.

    1976-01-01

    A major problem in the measurement of aircraft engine fan noise is the difficulty of simulating, in a ground-based facility, the noise that occurs during flight. Flight-type noise as contrasted to the usual ground-static test noise exhibits substantial reductions in both (1) the time unsteadiness of tone noise and (2) the mean level of tones calculated to be nonpropagating or cut-off. A model fan designed with cut-off of the fundamental tone was acoustically tested in the anechoic wind tunnel under both static and tunnel flow conditions. The properties that characterize flight-type noise were progressively simulated with increasing tunnel flow. The distinctly lobed directivity pattern of propagating rotor/stator interaction modes was also observed. The results imply that the excess noise attributed to the ingestion of the flow disturbances that prevail near most static test facilities was substantially reduced with tunnel flow. The anechoic wind tunnel appears to be a useful facility for applied research on aircraft engine fan noise under conditions of simulated flight.

  8. Understanding Your Test Results

    Science.gov (United States)

    ... serum: IgA, IgM, and IgG. It measures both polyclonal (normal) and monoclonal (myeloma-related) immunoglobulin, so if an increase in one of the antibody isotypes is found, further testing with electrophoresis is ...

  9. Subwavelength-Sized Narrow-Band Anechoic Waveguide Terminations

    Science.gov (United States)

    Santillán, Arturo; Ćrenlund, Emil; Bozhevolnyi, Sergey I.

    2016-11-01

    We propose and demonstrate the use of a pair of detuned acoustic resonators to efficiently absorb narrow-band sound waves in a terminated waveguide. The suggested configuration is relatively simple and advantageous for usage at low frequencies, since the dimensions of the resonators are very small compared to the wavelength. We present a theoretical description based on lumped parameters to calculate the absorption coefficient, which agrees very well with experimental data. The experimental results verify that the anechoic (reflection approximately -38 dB ) narrow-band (Δ f /f ˜0.1 ) termination with deeply subwavelength (sound absorption in a room, we demonstrate by use of numerical simulations that a given axial resonant excitation in a room can be practically eliminated. Thus, a reduction of approximately 24 dB in the average acoustic energy is achieved in the room when using only four Helmholtz resonators. We also discuss various scenarios of noise control in rooms.

  10. Pressure locking test results

    Energy Technology Data Exchange (ETDEWEB)

    DeWall, K.G.; Watkins, J.C.; McKellar, M.G.; Bramwell, D. [Idaho National Engineering Lab., Idaho Falls, ID (United States)] [and others

    1996-12-01

    The U.S. Nuclear Regulatory Commission (NRC), Office of Nuclear Regulatory Research, is funding the Idaho National Engineering Laboratory (INEL) in performing research to provide technical input for their use in evaluating responses to Generic Letter 95-07, {open_quotes}Pressure Locking and Thermal Binding of Safety-Related Power-Operated Gate Valves.{close_quotes} Pressure locking and thermal binding are phenomena that make a closed gate valve difficult to open. This paper discusses only the pressure locking phenomenon in a flexible-wedge gate valve; the authors will publish the results of their thermal binding research at a later date. Pressure locking can occur when operating sequences or temperature changes cause the pressure of the fluid in the bonnet (and, in most valves, between the discs) to be higher than the pressure on the upstream and downstream sides of the disc assembly. This high fluid pressure presses the discs against both seats, making the disc assembly harder to unseat than anticipated by the typical design calculations, which generally consider friction at only one of the two disc/seat interfaces. The high pressure of the bonnet fluid also changes the pressure distribution around the disc in a way that can further contribute to the unseating load. If the combined loads associated with pressure locking are very high, the actuator might not have the capacity to open the valve. The results of the NRC/INEL research discussed in this paper show that the relationship between bonnet pressure and pressure locking stem loads appears linear. The results also show that for this valve, seat leakage affects the bonnet pressurization rate when the valve is subjected to thermally induced pressure locking conditions.

  11. RF Anechoic Chambers, Tri-Service Research Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — In collaboration with the Navy, there are 12 RF Anechoic and static free exposure chambers located at TSRL. These chambers cover the majority of the RF spectrum and...

  12. Organic Separation Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Renee L.; Rinehart, Donald E.; Peterson, Reid A.

    2014-09-22

    Separable organics have been defined as “those organic compounds of very limited solubility in the bulk waste and that can form a separate liquid phase or layer” (Smalley and Nguyen 2013), and result from three main solvent extraction processes: U Plant Uranium Recovery Process, B Plant Waste Fractionation Process, and Plutonium Uranium Extraction (PUREX) Process. The primary organic solvents associated with tank solids are TBP, D2EHPA, and NPH. There is concern that, while this organic material is bound to the sludge particles as it is stored in the tanks, waste feed delivery activities, specifically transfer pump and mixer pump operations, could cause the organics to form a separated layer in the tank farms feed tank. Therefore, Washington River Protection Solutions (WRPS) is experimentally evaluating the potential of organic solvents separating from the tank solids (sludge) during waste feed delivery activities, specifically the waste mixing and transfer processes. Given the Hanford Tank Waste Treatment and Immobilization Plant (WTP) waste acceptance criteria per the Waste Feed Acceptance Criteria document (24590-WTP-RPT-MGT-11-014) that there is to be “no visible layer” of separable organics in the waste feed, this would result in the batch being unacceptable to transfer to WTP. This study is of particular importance to WRPS because of these WTP requirements.

  13. Emulating Spherical Wave Channel Models in Multi-probe Anechoic Chamber Setups

    DEFF Research Database (Denmark)

    Fan, Wei; Carreño, Xavier; Nielsen, Jesper Ødum;

    2015-01-01

    to emulate spherical wave channel models in multi-probe anechoic chamber setups. In this paper, a technique based on the field synthesis principle is proposed to approximate spherical waves emitted from arbitrarily located point sources with arbitrary polarizations. Simulation results show that static...... spherical waves can be reproduced with a limited number of probes, and the field synthesis accuracy of spherical wave depends on the location of the source point....

  14. Effectiveness of an inlet flow turbulence control device to simulate flight noise fan in an anechoic chamber

    Science.gov (United States)

    Woodward, R. P.; Wazyniak, J. A.; Shaw, L. M.; Mackinnon, M. J.

    1977-01-01

    A hemispherical inlet flow control device was tested on a 50.8 cm. (20-inch) diameter fan stage in the NASA-Lewis anechoic chamber. The control device used honeycomb and wire mesh to reduce turbulence intensities entering the fan. Far field acoustic power level results show about a 5 db reduction in blade passing tone and about 10 dB reduction in multiple pure tone sound power at 90% design fan speed with the inlet device in place. Hot film cross probes were inserted in the inlet to obtain data for two components of the turbulence at 65 and 90% design fan speed. Without the flow control device, the axial intensities were below 1.0%, while the circumferential intensities were almost twice this value. The inflow control device significantly reduced the circumferential turbulence intensities and also reduced the axial length scale.

  15. Effectiveness of an inlet flow turbulence control device to simulate flight fan noise in an anechoic chamber

    Science.gov (United States)

    Woodward, R. P.; Wazyniak, J. A.; Shaw, L. M.; Mackinnon, M. J.

    1977-01-01

    A hemispherical inlet flow control device was tested on a 50.8 cm. (20-inch) diameter fan stage in the NASA-Lewis Anechoic Chamber. The control device used honeycomb and wire mesh to reduce turbulence intensities entering the fan. Far field acoustic power level results showed about a 5 dB reduction in blade passing tone and about 10 dB reduction in multiple pure tone sound power at 90% design fan speed with the inlet device in place. Hot film cross probes were inserted in the inlet to obtain data for two components of the turbulence at 65 and 90% design fan speed. Without the flow control device the axial intensities were below 1.0%, while the circumferential intensities were almost twice this value. The inflow control device significantly reduced the circumferential turbulence intensities and also reduced the axial length scale.

  16. ISOCAM experiment cryogenic test results

    Science.gov (United States)

    de Sa, L.; Collaudin, B.

    The thermal requirements for ISOCAM, an IR camera to be mounted aboard the ISO satellite, are reviewed, and model predictions are matched with test results. The degree of model validation suggested by analytical prediction vs test results is described. Predictions of thermal conduction through mounting screws, from ball bearings, and of the heat distribution in the rotor and stator of a cryogenic stepper motor correlate well with actual test results. It is shown that ISOCAM meets the thermal requirements necessary for successful on-orbit operation. The model predicted such phenomena as 'chopped' motor function and the twofold increase in temperature resulting from continuous motor operation.

  17. NCV Flow Diagnostic Test Results

    Science.gov (United States)

    Cappuccio, Mina

    1999-01-01

    There were two objectives for this test. First, was to assess the reasons why there is approximately 1.5 drag counts (cts) discrepancy between measured and computed drag improvement of the Non-linear Cruise Validation (NCV) over the Technology Concept Airplane (TCA) wing body (WB) configurations. The Navier-Stokes (N-S) pre-test predictions from Boeing Commercial Airplane Group (BCAG) show 4.5 drag cts of improvement for NCV over TCA at a lift coefficient (CL) of 0. I at Mach 2.4. The pre-test predictions from Boeing Phantom Works - Long Beach, BPW-LB, show 3.75 drag cts of improvement. BCAG used OVERFLOW and BPW-LB used CFL3D. The first test entry to validate the improvement was held at the NASA Langley Research Center (LARC) UPV;T, test number 1687. The experimental results showed that the drag improvement was only 2.6 cts, not accounting for laminar run and trip drag. This is approximately 1.5 cts less than predicted computationally. In addition to the low Reynolds Number (RN) test, there was a high RN test in the Boeing Supersonic Wind Tunnel (BSWT) of NCV and TCA. BSV@T test 647 showed that the drag improvement of NCV over TCA was also 2.6 cts, but this did account for laminar run and trip drag. Every effort needed to be done to assess if the improvement measured in LaRC UPWT and BSWT was correct. The second objective, once the first objective was met, was to assess the performance increment of NCV over TCA accounting for the associated laminar run and trip drag corrections in LaRC UPWT. We know that the configurations tested have laminar flow on portions of the wing and have trip drag due to the mechanisms used to force the flow to go from laminar to turbulent aft of the transition location.

  18. 多功能电波暗室应用技术%Applied Technologies of Multifunctional Anechoic Chamber

    Institute of Scientific and Technical Information of China (English)

    董晓波; 肖玲

    2011-01-01

    该文介绍了电磁兼容测试需要的多功能电波暗室,成为多功能电波暗室应具备的基本功能,对满足标准要求的多功能电波暗室所需具备的性能指标进行描述及相应的测试要求,如基本的NSA,Svswr,FU。对在多功能电波暗室中进行不同项目测试时所对应的场地布置进行了分析,最后对多功能电波暗室的优劣进行了总结。%This article introduces what is the multifunctional anechoic chamber when we do EMC testing and test item it should support.It specifies the capability of NSA,Svswr,and FU of multifunctional anechoic chamber.It also does some analysis for test site of different test item.In the end,it summarizes the advantage and disadvantage of multifunctional anechoic.

  19. RSG Deployment Case Testing Results

    Energy Technology Data Exchange (ETDEWEB)

    Owsley, Stanley L.; Dodson, Michael G.; Hatchell, Brian K.; Seim, Thomas A.; Alexander, David L.; Hawthorne, Woodrow T.

    2005-09-01

    The RSG deployment case design is centered on taking the RSG system and producing a transport case that houses the RSG in a safe and controlled manner for transport. The transport case was driven by two conflicting constraints, first that the case be as light as possible, and second that it meet a stringent list of Military Specified requirements. The design team worked to extract every bit of weight from the design while striving to meet the rigorous Mil-Spec constraints. In the end compromises were made primarily on the specification side to control the overall weight of the transport case. This report outlines the case testing results.

  20. Test Results for CSTR Test 4

    Energy Technology Data Exchange (ETDEWEB)

    Lee, D.D.

    2001-05-31

    One of the 3 technologies currently being developed for the Savannah River Salt Waste Processing Program is the Small-Tank Tetraphenylborate Process (STTP). This process uses sodium tetraphenylborate to precipitate and remove radioactive Cs from the waste and monosodium titanate to sorb and remove radioactive Sr and actinides. ORNL is demonstrating this process at the 1:4000 scale using a 20-liter continuous-flow stirred tank reactor (CSTR) system. The primary goal of Test 4 was to verify that the STTP process could achieve and maintain the necessary Cs decontamination while TPB was actively decomposing. Even with TPB being decomposed by the off-normal conditions of this test, the decontaimination factor for {sup 137}Cs obtained for the filtrate from the Slurry Concentrating Tank ranged from 47,000 to 646,000, exceeding the WAC standard.

  1. Method for material characterization in a non-anechoic environment

    Science.gov (United States)

    Pometcu, L.; Sharaiha, A.; Benzerga, R.; Tamas, R. D.; Pouliguen, P.

    2016-04-01

    This paper presents a characterization method for extracting the reflection coefficient of materials and the real part of their permittivity. The characterization is performed in a real environment, as opposed to the classical measurement methods that require an anechoic chamber. In order to reduce the effects of the multipath propagation, a free space bistatic measurement was performed at different distances material-antennas in far field. By using a Teflon sample and a commercial absorbing material sample, measurements have been performed in order to validate the characterization technique.

  2. Results of Aluminosilicate Inhibitor Testing

    Energy Technology Data Exchange (ETDEWEB)

    Wilmarth, W.R.

    2001-06-27

    The aluminosilicate scale in the 2H Evaporator has precluded operation since late 1999. The chemistry of scale formation is known but the mechanism(s) for deposition are not well understood. Tests have been conducted to determine if chemical agents could prevent aluminosilicate formation under conditions similar to Tank 43H. Additionally, particle growth inhibition is also tested.

  3. FIRST RESULTS FROM OEDOTENSIOMETRIC TESTS

    Directory of Open Access Journals (Sweden)

    Luigi Cavazza

    2008-09-01

    Full Text Available An oedotensiometer was used to examine to examine the behaviour of sieved sample of a swelling soil (a vertisol as well as of the same soils treated with solution of Na+ + Ca2+ to simulate the soil changes from excessive irrigation with brackish water. The oedometer test consisted in an infiltration of water from below through a ceramic porous plate at a feeding pressure of +10 cm water and successive drainage under a depression mostly of -112 cm of water. The rate of water entry as well as the swelling rate of the sample were monitored. Preliminary considerations regards the domains in which the shrinkage curve of a swelling soil is subdivided and make hypothesis on the swelling process expected when the infiltration from below of the sample is applied. The results support the hypothesis that when the water pressure is applied some water enters rather rapidly in the larger structural pores and is followed later by the swelling in the smaller pores, responsible for the basic domain. This first conclusion demonstrates that the assumption of a simultaneous movement of solid and liquid components in the sample, which is the base of most theoretical developments for swelling soils, cannot be accepted for the tested samples. Some cases with water clogging on the sample surface confirm a late final swelling of the soil and permitted to evaluate the hydraulic conductivity of the swollen soil. These manifestations are more evident in sodicated soils. The loading of the sample reduces the swelling of the sample and seems to reduce its permeability. The reduction of the feeding water pressure further reduces the sample swelling. The draining process from saturated soil sample shows that most of the process occurs in the large pores of the structural domain. This gives the possibility to evaluate the water diffusivity coefficient for the structural domain of the sample. In draining the soil with the highest sodication there was a variation of soil volume

  4. Chemical compatibility screening test results

    Energy Technology Data Exchange (ETDEWEB)

    Nigrey, P.J.; Dickens, T.G.

    1997-12-01

    A program for evaluating packaging components that may be used in transporting mixed-waste forms has been developed and the first phase has been completed. This effort involved the screening of ten plastic materials in four simulant mixed-waste types. These plastics were butadiene-acrylonitrile copolymer rubber, cross-linked polyethylene (XLPE), epichlorohydrin rubber, ethylene-propylene rubber (EPDM), fluorocarbon (Viton or Kel-F), polytetrafluoroethylene, high-density polyethylene (HDPE), isobutylene-isoprene copolymer rubber (butyl), polypropylene, and styrene-butadiene rubber (SBR). The selected simulant mixed wastes were (1) an aqueous alkaline mixture of sodium nitrate and sodium nitrite; (2) a chlorinated hydrocarbon mixture; (3) a simulant liquid scintillation fluid; and (4) a mixture of ketones. The testing protocol involved exposing the respective materials to 286,000 rads of gamma radiation followed by 14-day exposures to the waste types at 60{degrees}C. The seal materials were tested using vapor transport rate (VTR) measurements while the liner materials were tested using specific gravity as a metric. For these tests, a screening criterion of 0.9 g/hr/m{sup 2} for VTR and a specific gravity change of 10% was used. Based on this work, it was concluded that while all seal materials passed exposure to the aqueous simulant mixed waste, EPDM and SBR had the lowest VTRs. In the chlorinated hydrocarbon simulant mixed waste, only Viton passed the screening tests. In both the simulant scintillation fluid mixed waste and the ketone mixture simulant mixed waste, none of the seal materials met the screening criteria. For specific gravity testing of liner materials, the data showed that while all materials with the exception of polypropylene passed the screening criteria, Kel-F, HDPE, and XLPE offered the greatest resistance to the combination of radiation and chemicals.

  5. Ultrasonic Transducer Irradiation Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Daw, Joshua [Idaho National Lab. (INL), Idaho Falls, ID (United States); Palmer, Joe [Idaho National Lab. (INL), Idaho Falls, ID (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Keller, Paul [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Montgomery, Robert [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chien, Hual-Te [Argonne National Lab. (ANL), Argonne, IL (United States); Kohse, Gordon [MIT (Massachusetts Inst. of Technology), Cambridge, MA (United States); Tittmann, Bernhard [Pennsylvania State Univ., University Park, PA (United States); Reinhardt, Brian [Pennsylvania State Univ., University Park, PA (United States); Rempe, Joy [Rempe and Associates, Idaho Falls, ID (United States)

    2015-02-01

    Ultrasonic technologies offer the potential for high-accuracy and -resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other ongoing efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. For this reason, the Pennsylvania State University (PSU) was awarded an ATR NSUF project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2. The goal of this research is to characterize and demonstrate magnetostrictive and piezoelectric transducer operation during irradiation, enabling the development of novel radiation-tolerant ultrasonic sensors for use in Material Testing Reactors (MTRs). As such, this test is an instrumented lead test and real-time transducer performance data is collected along with temperature and neutron and gamma flux data. The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers. To date, one piezoelectric

  6. A microwave applicator for uniform irradiation by circularly polarized waves in an anechoic chamber

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, W. Y.; Wu, M. H.; Wu, K. L.; Lin, M. H.; Teng, H. H.; Barnett, L. R.; Chu, K. R., E-mail: krchu@yahoo.com.tw [Department of Physics, National Taiwan University, Taipei, Taiwan (China); Tsai, Y. F.; Ko, C. C.; Yang, E. C. [Department of Entomology, National Taiwan University, Taipei, Taiwan (China); Jiang, J. A. [Department of Bio-Industrial Mechatronics Engineering, National Taiwan University, Taipei, Taiwan (China)

    2014-08-15

    Microwave applicators are widely employed for materials heating in scientific research and industrial applications, such as food processing, wood drying, ceramic sintering, chemical synthesis, waste treatment, and insect control. For the majority of microwave applicators, materials are heated in the standing waves of a resonant cavity, which can be highly efficient in energy consumption, but often lacks the field uniformity and controllability required for a scientific study. Here, we report a microwave applicator for rapid heating of small samples by highly uniform irradiation. It features an anechoic chamber, a 24-GHz microwave source, and a linear-to-circular polarization converter. With a rather low energy efficiency, such an applicator functions mainly as a research tool. This paper discusses the significance of its special features and describes the structure, in situ diagnostic tools, calculated and measured field patterns, and a preliminary heating test of the overall system.

  7. Research into Noise Generated by Domestic Appliances in the Anechoic Chamber

    Directory of Open Access Journals (Sweden)

    Agnė Žukauskienė

    2012-12-01

    Full Text Available Loud noise has a negative impact on the entire body, especially on listening. We can hear daily noise everywhere – in the street, at work or at home. The Department of Environmental Protection of Vilnius Gediminas Technical University has adjusted an anechoic chamber adapted for suppressing sound. Under the above introduced conditions, 15 appliances (5 vacuum cleaners, 5 hair dryers and 5 shaving machines have been tested. Equivalent sound pressure level of the vacuum cleaner has varied from 66 dBA to 83 dBA, that of the hair dryer has made from 64 dBA to 70 dBA and for the shaving machine – from 39 to 56 dBA.Article in Lithuanian

  8. A microwave applicator for uniform irradiation by circularly polarized waves in an anechoic chamber

    Science.gov (United States)

    Chiang, W. Y.; Wu, M. H.; Wu, K. L.; Lin, M. H.; Teng, H. H.; Tsai, Y. F.; Ko, C. C.; Yang, E. C.; Jiang, J. A.; Barnett, L. R.; Chu, K. R.

    2014-08-01

    Microwave applicators are widely employed for materials heating in scientific research and industrial applications, such as food processing, wood drying, ceramic sintering, chemical synthesis, waste treatment, and insect control. For the majority of microwave applicators, materials are heated in the standing waves of a resonant cavity, which can be highly efficient in energy consumption, but often lacks the field uniformity and controllability required for a scientific study. Here, we report a microwave applicator for rapid heating of small samples by highly uniform irradiation. It features an anechoic chamber, a 24-GHz microwave source, and a linear-to-circular polarization converter. With a rather low energy efficiency, such an applicator functions mainly as a research tool. This paper discusses the significance of its special features and describes the structure, in situ diagnostic tools, calculated and measured field patterns, and a preliminary heating test of the overall system.

  9. A Wide Band Strong Acoustic Absorption in a Locally Network Anechoic Coating

    Institute of Scientific and Technical Information of China (English)

    JIANG Heng; ZHANG Mi-Lin; WANG Yu-Ren; HU Yan-Ping; LAN Ding; WEI Bing-Chen

    2009-01-01

    Composite materials with interpenetrating network structures usually exhibit unexpected merit due to the cooperative interaction.Locally resonant phononic crystals (LRPC) exhibit excellent sound attenuation performance based on a periodical arrangement of sound wave scatters.Inspired by the interpenetrating network structure and the LRPC concept, we develop a locally network anechoic coating (LNAC) that can achieve a wide band of underwater strong acoustic absorption.The experimental results show that the LNAC possesses an excellent underwater acoustic absorbing capacity in a wide frequency range.Moreover, in order to investigate the impact of the interpenetrating network structure, we fabricate a faultage structure sample and the network is disconnected by hard polyurethane (PU).The experimental comparison between the LNAC and the faultage structure sample shows that the interpenetrating network structure of the LNAC plays an important role in achieving a wide band strong acoustic absorption.

  10. Classification of heart valve sounds from experiments in an anechoic water tank

    Energy Technology Data Exchange (ETDEWEB)

    Axelrod, M C; Clark, G A; Scott, D

    1999-06-01

    In vivo studies in both sheep and humans were plagued by a number of problems including movement artifacts, biological noise, low signal-to-noise ratio (SNR), chest-wall reverberation, and limited bandwidth recordings as discussed by [1]. To overcome these problems it was decided to record heart valve sounds under controlled conditions deep in an anechoic water tank, free from reverberation noise, including surface reflections. Experiments were conducted in a deep water tank at the Transdec facility in San Diego, which satisfies these requirements. The Transdec measurements are free of reverberations, but not totally free of acoustic and electrical noise. We used a high quality hydrophone together with a wide-band data acquisition system [2]. We recorded sounds from 100 repetitions of the opening-closing cycles on each of 50 different heart valves, including 21 SLS valves and 29 intact valves. The power spectrum of the opening and closing phases of each cycle were calculated and outlier spectra removed as described by Candy [2]. In this report, we discuss the results of our classification of the heart valve sound measurements. The goal of this classification task was to apply the fundamental classification algorithms developed for the clinical data in 1994 and 1996 to the measurements from the anechoic water tank. From the beginning of this project, LLNL's responsibility has been to process and classify the heart valve opening sounds. For this experiment, however, we processed both the opening sounds and closing sounds for comparison purposes. The results of this experiment show that the classifier did not perform well. We believe this is because of low signal-to-noise ratio and excessive variability in signal power from beat-to-beat for a given valve.

  11. Classification of heart valve sounds from experiments in an anechoic water tank

    Energy Technology Data Exchange (ETDEWEB)

    Axelrod, M C; Clark, G A; Scott, D

    1999-06-01

    In vivo studies in both sheep and humans were plagued by a number of problems including movement artifacts, biological noise, low signal-to-noise ratio (SNR), chest-wall reverberation, and limited bandwidth recordings as discussed by [1]. To overcome these problems it was decided to record heart valve sounds under controlled conditions deep in an anechoic water tank, free from reverberation noise. The main goal of this experiment was to obtain measurements of ''pure'' heart valve sounds free of the scattering effects of the body. Experiments were conducted at the Transdec facility in San Diego [2]. We used a high quality hydrophone together with a wide-band data acquisition system [2]. We recorded sounds from 100 repetitions of the opening-closing cycles on each of 50 different heart valves, including 21 SLS valves and 29 intact valves. The power spectrum of the opening and closing phases of each cycle were calculated and outlier spectra removed as described by Candy [2]. In this report, we discuss the results of our classification of the heart valve sound measurements. The goal of this classification task was to apply the fundamental classification algorithms developed for the clinical data in 1994 and 1996 to the measurements from the anechoic water tank. From the beginning of this project, LLNL's responsibility has been to process and classify the heart valve sounds. For this experiment, however, we processed both the opening sounds and closing sounds for comparison purposes. The results of this experiment show that the classifier did not perform well because of low signal-to-noise ratio and excessive variability in signal power from beat-to-beat for a given valve.

  12. Over the air test

    DEFF Research Database (Denmark)

    2015-01-01

    [1] This invention relates to over-the-air testing of a device in an anechoic chamber. In particular, the invention is suitable for simulating both uplink and downlink over-the-air communication with a device under test even when the anechoic chamber has different numbers of uplink and downlink...

  13. Common Diagnostic Test Results Over the Years

    Directory of Open Access Journals (Sweden)

    Aruvee Eve

    2016-12-01

    Full Text Available In this article, common test results over the years 2000 – 2016 are analysed. The test questions for new entrants were based on secondary school mathematics. The students took the test in the first lesson of the higher mathematics course. The test results were analysed by years, by tasks and by specialities, and their differences were found. The test results’ dependence on state-exams score was studied and other types of dependence were looked at.

  14. Reproducibility of AMPLICOR enterovirus PCR test results.

    OpenAIRE

    1997-01-01

    The reproducibility of AMPLICOR enterovirus PCR test results was determined with clinical samples of cerebrospinal fluid, serum, urine, and throat and rectal swabs. Among 608 samples from which duplicate aliquots were run simultaneously, only seven pairs gave discordant results. Among 104 samples from which duplicate aliquots were run in separate assays, no discordance was seen. Overall, the reproducibility of test kit results was 99% (705 of 712).

  15. Production LHC HTS power lead test results

    CERN Document Server

    Tartaglia, M; Fehér, S; Huang, Y; Orris, D F; Pischalnikov, Y; Rabehl, Roger Jon; Sylvester, C D; Zbasnik, J

    2005-01-01

    The Fermilab Magnet test facility has built and operated a test stand to characterize the performance of HTS power leads. We report here the results of production tests of 20 pairs of 7.5 kA HTS power leads manufactured by industry for installation in feed boxes for the LHC Interaction Region quadrupole strings. Included are discussions of the thermal, electrical, and quench characteristics under "standard" and "extreme" operating conditions, and the stability of performance across thermal cycles.

  16. Using Test Results to Improve Instruction.

    Science.gov (United States)

    Bassler, Otto C.; Caulkins, Thomas G.

    A model for summarizing test scores and using them to modify instructional programs is presented. The proposed model consists of two types of summaries of the data gathered through standardized tests. The first summary contains individual and single class results. Information in a "Class Item Response Record" chart provides individual student…

  17. Results of the HESSI Test Mishap Investigation

    Science.gov (United States)

    Worth, Daniel B.; Phillips, Rodney N.; Kross, Dennis A. (Technical Monitor)

    2000-01-01

    On March 21, 2000, the High-Energy Solar Spectroscopic Imager (HESSI) spacecraft was subjected to a series of vibration tests at the Jet Propulsion Laboratory (JPL) as a part of its flight certification program. The structural qualification test, denoted as the sineburst test, subjected the spacecraft to a major overtest that resulted in significant structural damage to the spacecraft. The HESSI Test Mishap Investigation Board (MIB) was formed on March 24, 2000, in response to a NASA headquarters request. Board membership included experts from NASA and the University of California at Berkeley. This paper will present the investigation methods, findings, and lessons learned from the HESSI mishap.

  18. Adaptive structures - Test hardware and experimental results

    Science.gov (United States)

    Wada, Ben K.; Fanson, James L.; Chen, Gun-Shing; Kuo, Chin-Po

    1990-01-01

    The facilities and procedures used at JPL to test adaptive structures such as the large deployable reflector (LDR) are described and preliminary results are reported. The applications of adaptive structures in future NASA missions are outlined, and the techniques which are employed to modify damping, stiffness, and isolation characteristics, as well as geometric changes, are listed. The development of adaptive structures is shown to be effective as a result of new actuators and sensors, and examples are listed for categories such as fiber optics, shape-memory materials, piezoelectrics, and electrorheological fluids. Some ground test results are described for laboratory truss structures and truss test beds, which are shown to be efficient and easy to assemble in space. Adaptive structures are shown to be important for precision space structures such as the LDR, and can alleviate ground test requirements.

  19. Cryogenic Test Results of Hextek Mirror

    Science.gov (United States)

    Hadaway, James; Stahl, H. Philip; Eng, Ron; Hogue, William

    2004-01-01

    A 250 mm diameter lightweight borosilicate mirror has been interferometrically tested from room-temperature down to 30 K at the X-Ray Calibration Facility (XRCF) at Marshall Space Flight Center (MSFC). The minor blank was manufactured by Hextek Corporation using a high-temperature gas fusion process and was then polished at MSFC. It is a sandwich-type mirror consisting of a thin face-sheet (approx.1.5 mm thick), a core structure (20 mm thick, approx.43 mm diameter cells, & 0.5-1.2 mm thick walls), and a thin back-sheet (3 mm thick). The mirror has a 2500 mm spherical radius-of- curvature @/lo). The areal density is 14 kg/sq m. The mirror was tested in the 1 m x 2 m chamber using an Instantaneous Phase Interferometer (PI) from ADE Phase Shift Technologies. The mirror was tested twice. The first test measured the change in surface figure from ambient to 30 K and the repeatability of the change. An attempt was then made by QED Technologies to cryo-figure the mirror using magnetorheological finishing. The second test measured the effectiveness of the cryo- figuring. This paper will describe the test goals, the test instrumentation, and the test results for these cryogenic tests.

  20. Directional loudness in an anechoic sound field, head-related transfer functions, and binaural summation

    DEFF Research Database (Denmark)

    Sivonen, Ville Pekka; Ellermeier, Wolfgang

    2006-01-01

    The effect of sound incidence angle on loudness was investigated using real sound sources positioned in an anechoic chamber. Eight normal-hearing listeners produced loudness matches between a frontal reference location and seven sources placed at other directions, both in the horizontal and media...... on the at-ear signals favored a sound-power summation model, according to which the maximum binaural gain is only 3dB, over competing models based on larger gains, or on the summation of monaural loudness indices....... planes. Matches were obtained via a two-interval, adaptive forced-choice (2AFC) procedure for three center frequencies (0.4, 1 and 5 kHz) and two overall levels (45 and 65 dB SPL). The results showed that loudness is not constant over sound incidence angles, with directional sensitivity varying over...... a range of up to 10 dB, exhibiting considerable frequency dependence, but only minor effects of overall level. The pattern of results varied substantially between subjects, but was largely accounted for by variations in individual head-related transfer functions. Modeling of binaural loudness based...

  1. The Results of the Second NACEF Test

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong-Hwan; Bae, Yoon-Yeong; Kim, Chan-Soo; Hong, Sung-Deok; Kim, Eung-Seon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    RCCS (Reactor Cavity Cooling System) is the only ex-vessel passive safety system that will ensure the safety of the PMR200, and its performance needs to be verified. For the difficulty of the fullscale test, a 1/4-scale RCCS facility, NACEF, was constructed at KAERI and a few tests have satisfactorily been performed. Here described are the results of the second main test which aimed at the evaluation of heat transfer with the scaled air velocity in the risers and the scaled air temperature increment during passing through the risers. The second main test was performed in the NACEF facility, the 1/4-scale RCCS mockup of PMR200. Natural convection cooling by buoyant force formed in the risers for a scaled condition. The RCCS in the prototypic PMR200 is expected to perform well. The heat transfer regime is in between the mixed convection and the forced convection.

  2. Results of shielding characteristics tests in Monju

    Energy Technology Data Exchange (ETDEWEB)

    Usami, Shin; Suzuoki, Zenro; Deshimaru, Takehide; Nakashima, Fumiaki [Japan Nuclear Cycle Development Inst., Tsuruga, Fukui (Japan)

    2001-06-01

    In the prototype fast breeder reactor Monju, the shielding characteristics tests were made around the reactor core, the primary heat transport system, and the fuel handling and storage system as a part of the system start-up tests from 0% to 45% of rated power from October 1993 through December 1995. The results of the measurements, analyses and evaluations in these tests validated the FBR shielding analysis methods and demonstrated that there was a safe shielding design margin in Monju. The important basic data for use in future FBR shielding design were successfully acquired. In order to obtain more substantial basic data and to improve the accuracy of the analyses, the next shielding measurements are planned for the period of the system start-up tests at the restart of Monju. (author)

  3. J series thruster thermal test results

    Science.gov (United States)

    Bechtel, R. T.; Dulgeroff, C. R.

    1982-01-01

    Test experience with J series ion thrusters have indicated that the present thruster design may result in excessive temperatures in areas which utilize organic materials such as wire insulation, with the resultant outgassing and potential contamination of insulating materials. Further, it appears that thermal data obtained with earlier thruster designs, such as the 700 series thruster, may not be directly applicable to the J series design. Two J series thrusters were fitted with thermocouples and critical temperatures measured for a variety of configurations and operating parameters. Completely enclosing the thruster to reduce facility contamination significantly increased temperatures prompting the selection of a compromise geometry for life testing. The operating parameter having the largest effect on temperatures was discharge power, while beam power affected little else than extraction system temperatures. Several off-normal operating modes were also investigated. Data believed to be sufficient to effectively modify existing thermal models were obtained from the tests.

  4. Cone Penetrometer N Factor Determination Testing Results

    Energy Technology Data Exchange (ETDEWEB)

    Follett, Jordan R.

    2014-03-05

    This document contains the results of testing activities to determine the empirical 'N Factor' for the cone penetrometer in kaolin clay simulant. The N Factor is used to releate resistance measurements taken with the cone penetrometer to shear strength.

  5. Application of Multi-Layered Polyurethane Foams for Flat-Walled Anechoic Linings

    DEFF Research Database (Denmark)

    Xu, J. F.; Buchholz, Jörg; Fricke, Fergus R.

    2006-01-01

    of the application of multi-layered polyurethane foams as the flat-walled anechoic lining. The investigation includes aspects such as the efficacy of a single layer of material, the minimum number of layers of linings to achieve the minimum overall thickness for low (100Hz), mid (250Hz) and high (500Hz) cut...

  6. Laboratory results of the AOF system testing

    Science.gov (United States)

    Kolb, Johann; Madec, Pierre-Yves; Arsenault, Robin; Oberti, Sylvain; Paufique, Jérôme; La Penna, Paolo; Ströbele, Stefan; Donaldson, Robert; Soenke, Christian; Suárez Valles, Marcos; Kiekebusch, Mario; Argomedo, Javier; Le Louarn, Miska; Vernet, Elise; Haguenauer, Pierre; Duhoux, Philippe; Aller-Carpentier, Emmanuel; Valenzuela, Jose Javier; Guerra, Juan Carlos

    2016-07-01

    For two years starting in February 2014, the AO modules GRAAL for HAWK-I and GALACSI for MUSE of the Adaptive Optics Facility project have undergone System Testing at ESO's Headquarters. They offer four different modes: NGS SCAO, LGS GLAO in the IR, LGS GLAO and LTAO in the visible. A detailed characterization of those modes was made possible by the existence of ASSIST, a test bench emulating an adaptive VLT including the Deformable Secondary Mirror, a star simulator and turbulence generator and a VLT focal plane re-imager. This phase aimed at validating all the possible components and loops of the AO modules before installation at the actual VLT that comprises the added complexity of real LGSs, a harsher non-reproducible environment and the adaptive telescope control. In this paper we present some of the major results obtained and challenges encountered during the phase of System Tests, like the preparation of the Acquisition sequence, the testing of the Jitter loop, the performance optimization in GLAO and the offload of low-order modes from the DSM to the telescope (restricted to the M2 hexapod). The System Tests concluded with the successful acceptance, shipping, installation and first commissioning of GRAAL in 2015 as well as the acceptance and shipping of GALACSI, ready for installation and commissioning early 2017.

  7. Field Cone Penetration Tests with Various Penetration Rates - Test Results

    DEFF Research Database (Denmark)

    Poulsen, Rikke; Nielsen, Benjaminn Nordahl; Ibsen, Lars Bo

    The test site is located at Nordre Ringgade near the town called Dronninglund in the northern Jutland in Denmark. The site area is relatively flat, and was chosen because it has a size of approximately 3 ha and contains a relatively thick deposit of silty soils. Furthermore the groundwater...... was encountered at approximately 0.2-0.6 m below the ground level. The soil stratigraphy of the test site was before test start identified by geotechnical borings results. The geotechnical borings indicated that the site contains of sandy silt with clay stripes from approx. 4.0 to 10 m. In the top the silty soil...... is very sandy with few clay stripes, and gradually the clay stripes increases wherefore the soil from approx. 10 m contains of clay with sandy silt stripes. Large soil sample was also collected from the test site in order to determine basic soil properties in the laboratory....

  8. Advanced Thermal Simulator Testing: Thermal Analysis and Test Results

    Science.gov (United States)

    Bragg-Sitton, Shannon M.; Dickens, Ricky; Dixon, David; Reid, Robert; Adams, Mike; Davis, Joe

    2008-01-01

    Work at the NASA Marshall Space Flight Center seeks to develop high fidelity, electrically heated thermal simulators that represent fuel elements in a nuclear reactor design to support non-nuclear testing applicable to the development of a space nuclear power or propulsion system. Comparison between the fuel pins and thermal simulators is made at the outer fuel clad surface, which corresponds to the outer sheath surface in the thermal simulator. The thermal simulators that are currently being tested correspond to a SNAP derivative reactor design that could be applied for Lunar surface power. These simulators are designed to meet the geometric and power requirements of a proposed surface power reactor design, accommodate testing of various axial power profiles, and incorporate imbedded instrumentation. This paper reports the results of thermal simulator analysis and testing in a bare element configuration, which does not incorporate active heat removal, and testing in a water-cooled calorimeter designed to mimic the heat removal that would be experienced in a reactor core.

  9. Preliminary test results for the SVX4

    Energy Technology Data Exchange (ETDEWEB)

    Christofek, L.; Hanagaki, K.; Rapidis, P.; Utes, M.; /Fermilab

    2005-06-01

    We present and summarize the preliminary test results for SVX4 chip testing. There are presently two versions of the SVX4. Version 2 has on-chip bypassing and Version 1 does not. The on-chip bypassing is a layer of transistors under the front-end analog pipeline that acts as a bypassing capacitor for the voltage supply. Its size is about a microfarad. We aggressively choose to test Version 2 because of this feature. The feature is advantageous for hybrid design because it eliminates the need for an additional passive component on the hybrid itself by placing it on the actual SVX4 die. Also, the SVX4 was designed to operate in two modes: D. and CDF. One can set which mode the chip will operate by placing a jumper in the proper position on the SVX4 chip carrier. In either mode, the chip can either use the operating parameters from the shift register or the shadow register. Similarly, this is selected by placing a jumper on the SVX4 chip carrier. This chip has this feature because it was unknown whether the new design of the shadow register would be operable. The shadow register is also call the SEU register or Single Event Upset register. An introduction into the functionality of the chip and an explanation on the difference between D. and CDF mode can be found in the SVX4 User's Manual [1].

  10. Arc melter demonstration baseline test results

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, N.R.; Chambers, A.G.; Anderson, G.L.; Oden, L.L.; O`Connor, W.K.; Turner, P.C.

    1994-07-01

    This report describes the test results and evaluation for the Phase 1 (baseline) arc melter vitrification test series conducted for the Buried Waste Integrated Demonstration program (BWID). Phase 1 tests were conducted on surrogate mixtures of as-incinerated wastes and soil. Some buried wastes, soils, and stored wastes at the INEL and other DOE sites, are contaminated with transuranic (TRU) radionuclides and hazardous organics and metals. The high temperature environment in an electric arc furnace may be used to process these wastes to produce materials suitable for final disposal. An electric arc furnace system can treat heterogeneous wastes and contaminated soils by (a) dissolving and retaining TRU elements and selected toxic metals as oxides in the slag phase, (b) destroying organic materials by dissociation, pyrolyzation, and combustion, and (c) capturing separated volatilized metals in the offgas system for further treatment. Structural metals in the waste may be melted and tapped separately for recycle or disposal, or these metals may be oxidized and dissolved into the slag. The molten slag, after cooling, will provide a glass/ceramic final waste form that is homogeneous, highly nonleachable, and extremely durable. These features make this waste form suitable for immobilization of TRU radionuclides and toxic metals for geologic timeframes. Further, the volume of contaminated wastes and soils will be substantially reduced in the process.

  11. Updated Results of Ultrasonic Transducer Irradiation Test

    Energy Technology Data Exchange (ETDEWEB)

    Daw, Joshua; Palmer, Joe [Idaho National Laboratory, P.O. Box 1625, MS 4112, Idaho Falls, ID, 38415-3840 (United States); Ramuhalli, Pradeep; Keller, Paul; Montgomery, Robert [Pacific Northwest National Laboratory, 902 Battelle Blvd. Richland, WA, 99354 (United States); Chien, Hual-Te [Argonne National Laboratory, 9700 S. Cass Avenue Argonne, IL, 60439 (United States); Tittmann, Bernhard; Reinhardt, Brian [Pennsylvania State University, 212 Earth and Engr. Sciences Building, University Park, PA, 16802 (United States); Kohse, Gordon [Massachusetts Institute of Technology, 77 Massachusetts Ave. Cambridge, MA 02139 (United States); Rempe, Joy [Rempe and Associates, LLC, 360 Stillwater, Idaho Falls, ID 83404 (United States); Villard, J.F. [Commissariat a l' energie atomique et aux energies alternatives, Centre d' etudes de Cadarache, 13108 Saint-Paul-lez-Durance (France)

    2015-07-01

    Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. To address this need, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 10{sup 21} n/cm{sup 2}. A multi-National Laboratory collaboration funded by the Nuclear Energy Enabling Technologies Advanced Sensors and Instrumentation (NEET-ASI) program also provided initial support for this effort. This irradiation, which started in February 2014, is an instrumented lead test and real-time transducer performance data are collected along with temperature and neutron and gamma flux data. The irradiation is ongoing and will continue to approximately mid-2015. To date, very encouraging results have been attained as several transducers continue to operate under irradiation. (authors)

  12. Results from the Cooler and Lead Tests

    Energy Technology Data Exchange (ETDEWEB)

    Green, Michael A

    2010-06-10

    The report presents the results of testing MICE spectrometer magnet current leads on a test apparatus that combines both the copper leads and the high temperature superconducting (HTS) leads with a single Cryomech PT415 cooler and liquid helium tank. The current is carried through the copper leads from 300 K to the top of the HTS leads. The current is then carried through the HTS leads to a feed-through from the vacuum space to the inside of a liquid helium tank. The experiment allows one to measure the performance of both cooler stages along with the performance of the leads. While the leads were powered we measured the voltage drops through the copper leads, through the HTS leads, through spliced to the feed-through, through the feed-through and through the low-temperature superconducting loop that connects one lead to the other. Measurements were made using the leads that were used in spectrometer magnet 1A and spectrometer magnet 2A. These are the same leads that were used for Superbend and Venus magnets at LBNL. The IL/A for these leads was 5.2 x 10{sup 6} m{sup -1}. The leads turned out to be too long. The same measurements were made using the leads that were installed in magnet 2B. The magnet 2B leads had an IL/A of 3.3 x 10{sup 6} A m{sup -1}. This report discusses the cooler performance and the measured electrical performance of the lead circuit that contains the copper leads and the superconducting leads. All of the HTS leads that were installed in magnet 2B were current tested using this apparatus.

  13. Subgroup effects despite homogeneous heterogeneity test results

    Directory of Open Access Journals (Sweden)

    Lubsen Jacobus

    2010-05-01

    Full Text Available Abstract Background Statistical tests of heterogeneity are very popular in meta-analyses, as heterogeneity might indicate subgroup effects. Lack of demonstrable statistical heterogeneity, however, might obscure clinical heterogeneity, meaning clinically relevant subgroup effects. Methods A qualitative, visual method to explore the potential for subgroup effects was provided by a modification of the forest plot, i.e., adding a vertical axis indicating the proportion of a subgroup variable in the individual trials. Such a plot was used to assess the potential for clinically relevant subgroup effects and was illustrated by a clinical example on the effects of antibiotics in children with acute otitis media. Results Statistical tests did not indicate heterogeneity in the meta-analysis on the effects of amoxicillin on acute otitis media (Q = 3.29, p = 0.51; I2 = 0%; T2 = 0. Nevertheless, in a modified forest plot, in which the individual trials were ordered by the proportion of children with bilateral otitis, a clear relation between bilaterality and treatment effects was observed (which was also found in an individual patient data meta-analysis of the included trials: p-value for interaction 0.021. Conclusions A modification of the forest plot, by including an additional (vertical axis indicating the proportion of a certain subgroup variable, is a qualitative, visual, and easy-to-interpret method to explore potential subgroup effects in studies included in meta-analyses.

  14. Tuned Chamber Core Panel Acoustic Test Results

    Science.gov (United States)

    Schiller, Noah H.; Allen, Albert R.

    2016-01-01

    This report documents acoustic testing of tuned chamber core panels, which can be used to supplement the low-frequency performance of conventional acoustic treatment. The tuned chamber core concept incorporates low-frequency noise control directly within the primary structure and is applicable to sandwich constructions with a directional core, including corrugated-, truss-, and fluted-core designs. These types of sandwich structures have long, hollow channels (or chambers) in the core. By adding small holes through one of the facesheets, the hollow chambers can be utilized as an array of low-frequency acoustic resonators. These resonators can then be used to attenuate low-frequency noise (below 400 Hz) inside a vehicle compartment without increasing the weight or size of the structure. The results of this test program demonstrate that the tuned chamber core concept is effective when used in isolation or combined with acoustic foam treatments. Specifically, an array of acoustic resonators integrated within the core of the panels was shown to improve both the low-frequency absorption and transmission loss of the structure in targeted one-third octave bands.

  15. Unit cell sparger test program and analysis of test results

    Energy Technology Data Exchange (ETDEWEB)

    Park, Choon Kyung; Song, C. H.; Cho, S.; Yoon, Y. J

    2003-11-01

    This report presents the results of test data from CPT-3 test and the effect of important parameters on the IRWST load. The object of CPT-3 test is to determine the influence of air mass in the piping on the IRWST (In-containment Refueling Water Storage Tank) boundary during an operation of Safety Depressurization and Vent System (SDVS). The test was conducted from an initial system pressure of 15.2 MPa, a steam temperature of 343.3 .deg. C, and an air mass of 3.34 lb. Following valve actuation, the pressure within the discharge line underwent pressure transient due to high pressure steam from the pressurizer and the discharged high pressure air formed air bubbles, which expanded and compressed periodically in the simulated IRWST. Air bubble oscillation was terminated within 2 s into the test. The magnitude of the pressure wave during the air clearing period was inversely proportional to the distance and very abrupt pressure spikes were observed in case the distance from the sparger holes to the submerged structure was less than 0.9 m. After the isolation valves were closed, the water in the simulated IRWST was considered to rise up to the 2.4m from the water surface in the quench tank. The amount of air mass in the piping, water temperature in the simulated IRWST, air temperature in the piping had not significant effect on the pressure loading during an air clearing period. However, the opening time of the isolation valve, steam mass flow rate, and submergence of an sparger have been shown to have great effects on the pressure loading during an air clearing period. 2 % of sparger flow area seems to be sufficient for the vacuum breaker area to mitigate the water hammering caused by abrupt water level rising during valve closure.

  16. Analysis of CEDM test result(1)

    Energy Technology Data Exchange (ETDEWEB)

    Jun, H. G.; Chung, C. H.; Yoon, Y. J.; Donh, C. H.; Park, J. K. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2001-05-01

    The performance tests of the control element drive mechanism (CEDM) of Korean Next Generation Reactor(KNGR) were carried out. The performance tests consist of endurance test, power test, air cooling test and drop test. The endurance test was carried out to get 500,650 steps (31,290.6 ft) of CEDM movement. In power test, the motor driving power was measured for the cases of withdrawl, inserting, and holding states of CEDM. In air cooling test, the power to move the CEA was calculated from the measurements of temperature rising of air and it was compared with the measurement of power test. The 678 times of the drop test were carried out. For all drop tests, the drop time was shorter than the acceptance criteria of 4 sec. The effects of loop temperature and flow rate were investigated in drop test. After endurance test, the CEDM assembly was disassembled and visually inspected, and it was found out that the motor are not injured, bur the drive shaft is damaged seriously. 3 refs., 34 figs., 17 tabs. (Author)

  17. Commissioning of ALFABURST: initial tests and results

    CERN Document Server

    Rajwade, Kaustubh; Lorimer, Duncan; Karastergiou, Aris; Werthimer, Dan; Siemion, Andrew; MacMahon, David; Cobb, Jeff; Williams, Christopher; Armour, Wes

    2016-01-01

    Fast Radio Bursts (FRBs) are apparently one-time, relatively bright radio pulses that have been observed in recent years. The origin of FRBs is currently unknown and many instruments are being built to detect more of these bursts to better characterize their physical properties and identify the source population. ALFABURST is one such instrument. ALFABURST takes advantage of the 7-beam Arecibo L-band Feed Array (ALFA) receiver on the 305-m Arecibo Radio Telescope in Puerto Rico, to detect FRBs in real-time at L-band (1.4 GHz). We present the results of recent on-sky tests and observations undertaken during the commissioning phase of the instrument. ALFABURST is now available for commensal observations with other ALFA projects.

  18. Results of the fourth Hanna field test

    Energy Technology Data Exchange (ETDEWEB)

    Covell, J. R.; Wojdac, L. F.; Barbour, F. A.; Gardner, G. W.; Glass, R.; Hommert, P. J.

    1980-01-01

    The second phase (Hanna IVB) of a coal gasification experiment near Hanna, Wyoming, was completed in September 1979. The experiment attempted to link and gasify coal between process wells spaced 34.3 meters apart. Intermediate wells were positioned between the process wells so that the link could be relayed over shorter distances. Reverse combustion linking was attempted over a 22.9-meter and a 11.4-meter distance of the total well spacing. Thermal activity was generally noted in the upper 3 meters of the coal seam during the link. Two attempts to gasify over the 34.3-meter distance resulted in the propagation of the burn front at the coal overburden interface. Post-burn evaluation indicates fractures as major influencing factors of the combustion process. The Hanna IVB field test provided much insight into influence that geologic features have on in situ coal combustion. The influence of these faults, permeable zones, and cleats, on the air flow patterns can drastically change the overall results of a gasification experiment and should be studied further. The overall results of Hanna IVB were discouraging because of the rapid decline in the heating values for the production gas and the amount of coal gasified. With more complete geologic characerization prior to experimentation and proper well completions, it is believed that most of the subsurface operational problems encountered during Hanna IV could have been avoided.

  19. Summary of CPAS EDU Testing Analysis Results

    Science.gov (United States)

    Romero, Leah M.; Bledsoe, Kristin J.; Davidson, John.; Engert, Meagan E.; Fraire, Usbaldo, Jr.; Galaviz, Fernando S.; Galvin, Patrick J.; Ray, Eric S.; Varela, Jose

    2015-01-01

    The Orion program's Capsule Parachute Assembly System (CPAS) project is currently conducting its third generation of testing, the Engineering Development Unit (EDU) series. This series utilizes two test articles, a dart-shaped Parachute Compartment Drop Test Vehicle (PCDTV) and capsule-shaped Parachute Test Vehicle (PTV), both of which include a full size, flight-like parachute system and require a pallet delivery system for aircraft extraction. To date, 15 tests have been completed, including six with PCDTVs and nine with PTVs. Two of the PTV tests included the Forward Bay Cover (FBC) provided by Lockheed Martin. Advancements in modeling techniques applicable to parachute fly-out, vehicle rate of descent, torque, and load train, also occurred during the EDU testing series. An upgrade from a composite to an independent parachute simulation allowed parachute modeling at a higher level of fidelity than during previous generations. The complexity of separating the test vehicles from their pallet delivery systems necessitated the use the Automatic Dynamic Analysis of Mechanical Systems (ADAMS) simulator for modeling mated vehicle aircraft extraction and separation. This paper gives an overview of each EDU test and summarizes the development of CPAS analysis tools and techniques during EDU testing.

  20. Acknowledging the results of blood tests

    DEFF Research Database (Denmark)

    Torkilsheyggi, Arnvør Martinsdottir á; Hertzum, Morten

    At the studied hospital, physicians from the Medical and Surgical Departments work some of their shifts in the Emergency Department (ED). Though icons showing the blood-test process were introduced on electronic whiteboards in the ED, these icons did not lead to increased attention to test...

  1. Ultra-Low Power Transmitter Test Results

    Science.gov (United States)

    2014-12-01

    fabricate, and test an ultra-low-power transmitter and integrate it with a non-contact electroencephalogram ( EEG )/electrocardiogram (ECG) device...the current transmitter to investigate ways to remove design flaws and improve the design performance. The crystal oscillator had issues with its...it more robust. The chip will need to be re-designed and fabricated again to fix issues uncovered by testing. If the second revision of the chip is

  2. Initial Burn Pan (JMTF) Testing Results

    Science.gov (United States)

    2016-03-01

    report does not constitute a standard, specification, or regulation . Mr. James Fletcher E&W Branch Chief United...locations around the test area. A remote control drone equipped with a GoPro camera was also used to video the third test. All recorded video and still...further in advance; and the process to get it to the LSI may need to be revised to ensure CG, state and federal regulations are met. This procedure

  3. STRATEGY/RESULT FOR SRF TEST INFRASTRUCTURES

    CERN Document Server

    Weingarten, W

    2011-01-01

    The report summarizes the requirements needed to further develop the technology of RF superconductivity for accelerator application beyond the present state of the art. In relation to emerging European accelerator projects present collaboration schemes are identified. The required test capacities are described and compared with the available ones. Based on a short historical review, the actual performance limits of superconducting cavities are evaluated and measures are proposed to overcome them.

  4. Round Robin Fatigue Crack Growth Testing Results

    Science.gov (United States)

    2006-11-01

    Equipment and Setup a. SATEC b. 20 kip (7075-T6); 55 kip (2024-T351) c. Test control hardware/ software i. Hardware: Teststar Ilm ii. Software : Station...Stractlvrai Lif,"e Exteraiocn (CAStLE) DeOartn~ont of Enineering Mechanics, FIC US~.TA/DFFN 1DSA-FA-*rR-2006-10 23-54 arhi Drive, Suite 2J2, U-SAF Academy CO

  5. Results of workplace drug testing in Norway

    Directory of Open Access Journals (Sweden)

    Hilde Marie Erøy Lund

    2011-12-01

    Full Text Available Workplace drug testing is less common in Norway than in many other countries. During the period from 2000-2006, 13469 urine or blood samples from employees in the offshore industry, shipping companies and aviation industry were submitted to the Norwegian Institute of Public Health for drug testing. The samples were analysed for benzodiazepines, illicit drugs, muscle relaxants with sedating properties, opioids and z-hypnotics. In total, 2.9% of the samples were positive for one or more substances. During the study period the prevalence decreased for morphine (from 1.9% to 1.1% and increased for amphetamine (from 0.04% to 0.6%, clonazepam (from 0% to 0.1%, methamphetamine (from 0.04% to 0.6%, nitrazepam (from 0% to 0.4% and oxazepam (from 0.5% to 1.3% (p<0.05. There was no significant change in prevalence for the other substances included in the analytical programme. Illicit drugs were significantly associated with lower age (OR: 0.93, p<0.05. This study found low prevalence of drugs among employees in companies with workplace drug testing programmes in Norway.

  6. Preliminary Results of Field Emission Cathode Tests

    Science.gov (United States)

    Sovey, James S.; Kovaleski, Scott D.

    2001-01-01

    Preliminary screening tests of field emission cathodes such as chemical vapor deposited (CVD) diamond, textured pyrolytic graphite, and textured copper were conducted at background pressures typical of electric thruster test facilities to assess cathode performance and stability. Very low power electric thrusters which provide tens to hundreds micronewtons of thrust may need field emission neutralizers that have a capability of tens to hundreds of microamperes. From current voltage characteristics, it was found that the CVD diamond and textured metals cathodes clearly satisfied the Fowler-Nordheim emission relation. The CVD diamond and a textured copper cathode had average current densities of 270 and 380 mA/sq cm, respectively, at the beginning-of-life. After a few hours of operation the cathode emission currents degraded by 40 to 75% at background pressures in the 10(exp -5) Pa to 10(exp -4) Pa range. The textured pyrolytic graphite had a modest current density at beginning-of-life of 84 mA/sq cm, but this cathode was the most stable of all. Extended testing of the most promising cathodes is warranted to determine if current degradation is a burn-in effect or whether it is a long-term degradation process. Preliminary experiments with ferroelectric emission cathodes, which are ceramics with spontaneous electric polarization, were conducted. Peak current densities of 30 to 120 mA/sq cm were obtained for pulse durations of about 500 ns in the 10(exp -4) Pa pressure range.

  7. Results from some anode wire aging tests

    Energy Technology Data Exchange (ETDEWEB)

    Juricic, I.; Kadyk, J.A.

    1986-01-01

    Using twin setups to test anode wire aging in small gas avalanche tubes, a variety of different gas mixtures were tried and other parameters were varied to study their effects upon the gain drop, nomalized to charge transfer: - 1/Q dI/I. This was found to be quite sensitive to the purity of the gases, and also sensitive to the nominal gain and the gas flow rate. The wire surface material can also significantly affect the aging, as can additives, such as ethanol or water vapor. Certain gas mixtures have been found to be consistent with zero aging at the sensitivity level of this technique.

  8. Test Results of a Phi Monitoring System

    CERN Document Server

    Figueroa, Carlos; Burgos, C; Ferrrando, A; Matorras, Francisco; Molinero, Antonio; Rodriguo, T; Shvachkin, V

    1997-01-01

    The development and tests of a Phi monitoring system prototype designed for the CMS Muon Spectrometer alignment are described. The system, using a sweeping laser beam, defines a light reference plane to be used for the continuous monitoring of the Muon detectors. The performance of the system in the Laboratory was satisfactory. It showed good stability and linearity response behaviour. With the appropriate selection of components it can monitor large range position shifts ( up to 1-2 cm) with good accuracy at long distances ( ~ 60 mu accuracy at 10 m).

  9. RESULTS OF INITIAL AMMONIA OXIDATION TESTING

    Energy Technology Data Exchange (ETDEWEB)

    Nash, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fowley, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-12-30

    This memo presents an experimental survey of aqueous phase chemical processes to remove aqueous ammonia from waste process streams. Ammonia is generated in both the current Hanford waste flowsheet and in future waste processing. Much ammonia will be generated in the Low Activity Waste (LAW) melters.i Testing with simulants in glass melters at Catholic University has demonstrated the significant ammonia production.ii The primary reaction there is the reducing action of sugar on nitrate in the melter cold cap. Ammonia has been found to be a problem in secondary waste stabilization. Ammonia vapors are noxious and destruction of ammonia could reduce hazards to waste treatment process personnel. It is easily evolved especially when ammonia-bearing solutions are adjusted to high pH.

  10. Panoramic night vision goggle flight test results

    Science.gov (United States)

    Franck, Douglas L.; Geiselman, Eric E.; Craig, Jeffrey L.

    2000-06-01

    The Panoramic Night Vision Goggle (PNVG) has begun operational test and evaluation with its 100-degree horizontal by 40-degree vertical field of view (FOV) on different aircraft and at different locations. Two configurations of the PNVG are being evaluated. The first configuration design (PNVG I) is very low in profile and fits underneath a visor. PNVG I can be retained by the pilot during ejection. This configuration is interchangeable with a day helmet mounted tracker and display through a standard universal connector. The second configuration (PNVG II) resembles the currently fielded 40-degree circular FOV Aviator Night Vision Imaging Systems (ANVIS) and is designed for non-ejection seat aircraft and ground applications. Pilots completed subjective questionnaires after each flight to compare the capability of the 100-degree horizontal by 40-degree vertical PNVG to the 40-degree circular ANVIS across different operational tasks. This paper discusses current findings and pilot feedback from the flight trials objectives of the next phase of the PNVG program are also discussed.

  11. Uncertainty in in-place filter test results

    Energy Technology Data Exchange (ETDEWEB)

    Scripsick, R.C.; Beckman, R.J.; Mokler, B.V.

    1996-12-31

    Some benefits of accounting for uncertainty in in-place filter test results are explored. Information the test results provide relative to system performance acceptance limits is evaluated in terms of test result uncertainty. An expression for test result uncertainty is used to estimate uncertainty in in-place filter tests on an example air cleaning system. Modifications to the system test geometry are evaluated in terms of effects on test result uncertainty.

  12. Microchannel anechoic corner for size-selective separation and medium exchange via traveling surface acoustic waves.

    Science.gov (United States)

    Destgeer, Ghulam; Ha, Byung Hang; Park, Jinsoo; Jung, Jin Ho; Alazzam, Anas; Sung, Hyung Jin

    2015-05-05

    We demonstrate a miniaturized acoustofluidic device composed of a pair of slanted interdigitated transducers (SIDTs) and a polydimethylsiloxane microchannel for achieving size-selective separation and exchange of medium around polystyrene particles in a continuous, label-free, and contactless fashion. The SIDTs, deposited parallel to each other, produce tunable traveling surface acoustic waves (TSAWs) at desired locations, which, in turn, yield an anechoic corner inside the microchannel that is used to selectively deflect particles of choice from their streamlines. The TSAWs with frequency fR originating from the right SIDT and propagating left toward the microchannel normal to the fluid flow direction, laterally deflect larger particles with diameter d1 from the hydrodynamically focused sample fluid that carries other particles as well with diameters d2 and d3, such that d1 > d2 > d3. The deflected particles (d1) are pushed into the top-left corner of the microchannel. Downstream, the TSAWs with frequency fL, such that fL > fR, disseminating from the left SIDT, deflect the medium-sized particles (d2) rightward, leaving behind the larger particles (d1) unaffected in the top-left anechoic corner and the smaller particles (d3) in the middle of the microchannel, thereby achieving particle separation. A particle not present in the anechoic corner could be deflected rightward to realize twice the medium exchange. In this work, the three-way separation of polystyrene particles with diameters of 3, 4.2, and 5 μm and 3, 5, and 7 μm is achieved using two separate devices. Moreover, these devices are used to demonstrate multimedium exchange around polystyrene particles ∼5 μm and 7 μm in diameter.

  13. Covariance-based Spatial Channel Structure Emulation for MIMO OTA Testing

    DEFF Research Database (Denmark)

    Tsakalaki, Elpiniki; Alrabadi, Osama; Fan, Wei;

    2014-01-01

    The paper presents a general framework for recreating the spatial channel structure in a MIMO over-the-air (OTA) multiprobe anechoic chamber testing setup. The idea is to find the power weights of the spatial taps (antenna probes) that minimize a certain distance between the spatial channel covar...... among the antennas-under-test by considering the whole spatial covariance structure. The simulation results validate the improved performance of the suggested approach in terms of emulation accuracy compared to the key emulation methods proposed in the literature.......The paper presents a general framework for recreating the spatial channel structure in a MIMO over-the-air (OTA) multiprobe anechoic chamber testing setup. The idea is to find the power weights of the spatial taps (antenna probes) that minimize a certain distance between the spatial channel...

  14. Sickle Cell Trait in Blacks Can Skew Diabetes Test Results

    Science.gov (United States)

    ... page: https://medlineplus.gov/news/fullstory_163463.html Sickle Cell Trait in Blacks Can Skew Diabetes Test Results ... less accurate in black people who have the sickle cell anemia trait, a new study says. The test ...

  15. Effects of testing conditions on conceptual survey results

    Directory of Open Access Journals (Sweden)

    Lin Ding

    2008-06-01

    Full Text Available Pre-testing and post-testing is a commonly used method in Physics Education Research to assess student learning gains. It is well recognized in the community that timings and incentives in delivering conceptual tests can impact test results. However, it is difficult to control these variables across different studies. As a common practice, a pre-test is often administered either at or near the beginning of a course, while a post-test can be given either at or near the end of a course. Also, in conducting such tests there often is no norm as to whether incentives should be offered to students. Because these variations can significantly affect test results, it is important to study and document their impact. We analyzed five years of data that were collected at The Ohio State University from over 2100 students, who took both the pre-test and post-test of the Conceptual Survey of Electricity and Magnetism under various timings and incentives. We observed that the actual time frame for giving a test has a marked effect on the test results and that incentive granting also has a significant influence on test outcomes. These results suggest that one should carefully monitor and document the conditions under which tests are administered.

  16. Investigation of underwater sound scattering on a cylindrical shell coated with anechoic coatings by the finite element metho d based on an equivalent parameter inversion%基于等效参数反演的敷设声学覆盖层的水下圆柱壳体声散射研究∗

    Institute of Scientific and Technical Information of China (English)

    金国梁; 尹剑飞; 温激鸿; 温熙森

    2016-01-01

    Anechoic coating attached to the surface of an underwater object is used for absorbing sound wave thereby reducing the reflection. The anechoic coating is often made of viscoelastic materials embedded with designed acoustic substruc-tures, such as air cavities. The prediction of sound scattering on underwater object coated with such materials can be challenging due to the complex geometry of the anechoic coating, and it has been a research subject of interest in underwater acoustics. In this paper, we study the sound scattering on an infinite cylindrical shell coated with anechoic coating. Two types of coatings are considered: one is a layer of homogeneous isotropic material, and the other is a layer of homogeneous isotropic material with periodically embedded cylindrical air cavities. We use an equivalent method, in which the anechoic coating with air-filled cavities is regarded as a homogeneous isotropic material with equivalent material properties. The key point of the equivalent method is to ignore the internal structure of the anechoic coating, and the anechoic coating is considered as a homogeneous isotropic layer with the same complex reflection coefficient. These equivalent material properties are acquired based on the data of complex reflection coefficient obtained from either the physical experiment using water-filled impedance tube or the numerical experiment using the finite element method with COMSOL Multiphysics software. Then a genetic algorithm is used to inversely calculate the equivalent Young’s modulus, Poisson’s ratio, and damping loss factor of the coating which has the same reflection coefficient as the original coating. The results of the equivalent material properties show that 1) the three properties are all frequency dependent;2) in general, equivalent Young’s modulus increases with the increase of frequency, meanwhile the equivalent damping loss factor tends to decrease; 3) there is a wide variation in the results of equivalent

  17. Correspondence - Characterization of the effective performance of a high-frequency annular-array-based imaging system using anechoic-pipe phantoms.

    Science.gov (United States)

    Filoux, Erwan; Mamou, Jonathan; Moran, Carmel M; Pye, Stephen D; Ketterling, Jeffrey A

    2012-12-01

    A resolution integral (RI) method based on anechoic- pipe, tissue-mimicking phantoms was used to compare the detection capabilities of high-frequency imaging systems based on a single-element transducer, a state-of-the-art 256-element linear array, or a 5-element annular array. All transducers had a central frequency of 40 MHz with similar conventionally measured axial and lateral resolutions (about 50 and 85 μm, respectively). Using the RI metric, the annular array achieved the highest performance (RI = 60), followed by the linear array (RI = 47), and the single-element transducer (RI = 24). Results showed that the RI metric could be used to efficiently quantify the effective transducer performance and compare the image quality of different systems.

  18. Irradiation Effects Test Series: Test IE-2. Test results report. [PWR

    Energy Technology Data Exchange (ETDEWEB)

    Allison, C. M.; Croucher, D. W.; Ploger, S. A.; Mehner, A. S.

    1977-08-01

    The report describes the results of a test using four 0.97-m long PWR-type fuel rods with differences in diametral gap and cladding irradiation. The objective of this test was to provide information about the effects of these differences on fuel rod behavior during quasi-equilibrium and film boiling operation. The fuel rods were subjected to a series of preconditioning power cycles of less than 30 kW/m. Rod powers were then increased to 68 kW/m at a coolant mass flux of 4900 kg/s-m/sup 2/. After one hour at 68 kW/m, a power-cooling-mismatch sequence was initiated by a flow reduction at constant power. At a flow of 2550 kg/s-m/sup 2/, the onset of film boiling occurred on one rod, Rod IE-011. An additional flow reduction to 2245 kg/s-m/sup 2/ caused the onset of film boiling on the remaining three rods. Data are presented on the behavior of fuel rods during quasiequilibrium and during film boiling operation. The effects of initial gap size, cladding irradiation, rod power cycling, a rapid power increase, and sustained film boiling are discussed. These discussions are based on measured test data, preliminary postirradiation examination results, and comparisons of results with FRAP-T3 computer model calculations.

  19. Transabdominal ultrasonography of the small bowel after oral administration of a non-absorbable anechoic solution: Comparison with barium enteroclysis

    Energy Technology Data Exchange (ETDEWEB)

    Cittadini, Giuseppe; Giasotto, Veronica; Garlaschi, Giacomo; De Cicco, Enzo; Gallo, Alessandra; Cittadini, Giorgio

    2001-03-01

    AIM: The aim of this study was to determine if oral administration of a non-absorbable anechoic solution conveys any benefit during abdominal ultrasound (US), with special reference to its accuracy. MATERIALS AND METHODS: Fifty-three adult out-patients scheduled for small bowel barium enema (SBE) were included. The day before SBE all patients underwent abdominal US before and after oral administration of an isotonic non-absorbable electrolyte solution containing polyethylene glycol (PEG-ELS). Sensitivity and specificity were evaluated using SBE as a gold standard. RESULTS: After ingestion of PEG-ELS satisfactory distension of the intestinal lumen was obtained (11-25 mm) with sequential visualization of jejunoileal loops in 30.9 {+-} 17.3 min. In 15 out of 53 cases both US and SBE showed bowel changes characteristic of Crohn's disease. In three out of 53 cases both US and SBE showed neoplasms. In one out of 53 cases US was negative, SBE positive for local nodularity and ulcerations typical of Crohn's disease. In one out of 53 cases US was negative, SBE positive for macronodularity consistent with coeliac disease. In five out of 53 cases US was negative, while SBE was positive for mininodularity expressive of lymphoid hyperplasia. In 28 out of 53 cases both examinations were negative. CONCLUSION: PEG-ELS administration allows a thorough US investigation of the small bowel, with fair sensitivity (72%) and excellent specificity (100%). False negative findings are mainly due to lymphoid hyperplasia, a feature of uncertain significance in adults. Cittadini G. et al.(2001)

  20. Hawaiian Electric Advanced Inverter Test Plan - Result Summary

    Energy Technology Data Exchange (ETDEWEB)

    Hoke, Anderson; Nelson, Austin; Prabakar, Kumaraguru; Nagarajan, Adarsh

    2016-10-14

    This presentation is intended to share the results of lab testing of five PV inverters with the Hawaiian Electric Companies and other stakeholders and interested parties. The tests included baseline testing of advanced inverter grid support functions, as well as distribution circuit-level tests to examine the impact of the PV inverters on simulated distribution feeders using power hardware-in-the-loop (PHIL) techniques. hardware-in-the-loop (PHIL) techniques.

  1. Comparing dynamic and static test results of bored piles

    OpenAIRE

    Long, Michael

    2007-01-01

    Due to increasing time, cost and transportation difficulties, Irish contractors are seeking an alternative to conventional static pile load tests. As a result several firms have adopted dynamic testing techniques to supplement and in some cases to replace conventional static tests. In order to assess the reliability of the systems and to address the concerns of owners and consulting engineers, a database comprising 43 pairs of static and dynamic tests on piles from 24 sites aro...

  2. Results of Detailed Hydrologic Characterization Tests - Fiscal Year 1999

    Energy Technology Data Exchange (ETDEWEB)

    Spane, Frank A.; Thorne, Paul D.; Newcomer, Darrell R.

    2001-01-19

    This report provides the results of detailed hydrologic characterization tests conducted within newly constructed Hanford Site wells during FY 1999. Detailed characterization tests performed during FY 1999 included: groundwater flow characterization, barometric response evaluation, slug tests, single-well tracer tests, constant-rate pumping tests, and in-well vertical flow tests. Hydraulic property estimates obtained from the detailed hydrologic tests include: transmissivity, hydraulic conductivity, specific yield, effective porosity, in-well lateral flow velocity, aquifer flow velocity, vertical distribution of hydraulic conductivity (within the well-screen section) and in-well vertical flow velocity. In addition, local groundwater flow characteristics (i.e., hydraulic gradient and flow direction) were determined for four sites where detailed well testing was performed.

  3. Environmental testing results over a tracker drive train

    Science.gov (United States)

    Martínez, María; Calvo-Parra, Gustavo; Gil, Eduardo; de la Rubia, Oscar; Hillebrand, Mario; Rubio, Francisca; Aipperspach, Wolfgang; Gombert, Andreas

    2014-09-01

    Environmental testing following the draft of the IEC62817 standard has been carried out at ISFOC using a Soitec Solar tracker drive. The objective of this work is twofold; first to assure that the tracker design can perform under varying conditions and survive under extreme conditions and secondly to test the viability and usefulness of the tests described in the standard. After some changes in the device under test (specifically, gear-box oil) the drive system produced satisfactory results, assuring its performance under operational temperatures. Therefore, this work has demonstrated that the tests described in the standard are useful for detecting early failures.

  4. Test results judgment method based on BIT faults

    Institute of Scientific and Technical Information of China (English)

    Wang Gang; Qiu Jing; Liu Guanjun; Lyu Kehong

    2015-01-01

    Built-in-test (BIT) is responsible for equipment fault detection, so the test data correct-ness directly influences diagnosis results. Equipment suffers all kinds of environment stresses, such as temperature, vibration, and electromagnetic stress. As embedded testing facility, BIT also suffers from these stresses and the interferences/faults are caused, so that the test course is influenced, resulting in incredible results. Therefore it is necessary to monitor test data and judge test failures. Stress monitor and BIT self-diagnosis would redound to BIT reliability, but the existing anti-jamming researches are mainly safeguard design and signal process. This paper focuses on test results monitor and BIT equipment (BITE) failure judge, and a series of improved approaches is proposed. Firstly the stress influences on components are illustrated and the effects on the diagnosis results are summarized. Secondly a composite BIT program is proposed with information integra-tion, and a stress monitor program is given. Thirdly, based on the detailed analysis of system faults and forms of BIT results, the test sequence control method is proposed. It assists BITE failure judge and reduces error probability. Finally the validation cases prove that these approaches enhance credibility.

  5. Results of recent KROTOS FCI tests. Alumina vs. corium melts

    Energy Technology Data Exchange (ETDEWEB)

    Huhtiniemi, I.; Magallon, D.; Hohmann, H. [Commission of the European Communities, Ispra (Italy). Joint Research Center

    1998-01-01

    Recent results from KROTOS fuel-coolant interaction experiments are discussed. Five tests with alumina were performed under highly subcooled conditions, all of these tests resulted in spontaneous steam explosions. Additionally, four tests were performed at low subcooling to confirm, on one hand, the suppression of spontaneous steam explosions under such conditions and, on the other hand, that such a system is still triggerable using an external initiator. The other test parameters in these alumina tests included the melt superheat and the initial pressure. All the tests in the investigated superheat range (150 K - 750 K) produced a steam explosion and no evidence of the explosion suppression by the elevated initial pressure (in the limited range of 0.1 - 0.375 MPa) was observed in the alumina tests. The corium test series include a test with 3 kg of melt under both subcooled and near saturated conditions at ambient pressure. Two additional tests were performed with subcooled water; one test was performed at an elevated pressure of 0.2 MPa with 2.4 kg of melt and another test with 5.1 kg of melt at ambient pressure. None of these tests with corium produced a propagating energetic steam explosion. However, propagating low energy (about twice the energy of the trigger pulse) events were observed. All corium tests produced significantly higher water level swells during the mixing phase than the corresponding alumina tests. Present experimental evidence suggests that the water depletion in the mixing zone suppresses energetic steam explosions with corium melts at ambient pressure and in the present pour geometry. Processes that could produce such a difference in void generation are discussed. (author)

  6. New results from pulse tests in the CABRI reactor

    Energy Technology Data Exchange (ETDEWEB)

    Schmitz, F.; Papin, J.; Haessler, M. [Institut de Proterction et de Surete Nucleaire, Saint Paul Lez Durance (France)] [and others

    1996-03-01

    At the 21st and 22nd WRSM (1,2), the motivation and objectives of the French program on the behaviour of high burnup PWR fuel under RIA conditions in the CABRI test reactor has been presented. The major results of the three first tests of the test matrix were presented and in particular REP-Na1, which failed at an unexpected low level of fuel enthalpy, was exposed to the community of nuclear safety research. At this time, no final understanding was reached for the origin of the failure. This objective is reached now. Two further tests, REP-Na4 and 5, have been performed in 1995, they demonstrated a satisfactory and safe behaviour by resisting to the early phase of severe loading during the RIA pulse test. Further examination work and analytical testing is in progress and the next tests with MOX fuel are being prepared.

  7. Mechanical properties testing and results for thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Cruse, T.A.; Johnsen, B.P.; Nagy, A.

    1995-10-01

    The paper reports on several years of mechanical testing of thermal barrier coatings. The test results were generated to support the development of durability models for the coatings in heat engine applications. The test data that are reviewed include modulus, static strength, and fatigue strength data. The test methods and results are discussed, along with the significant difficulties inherent in mechanical testing of thermal barrier coating materials. The materials include 7 percent wt. and 8 percent wt. yttria, partially stabilized zirconia as well as a cermet material. Both low pressure plasma spray and electron-beam physical vapor deposited coatings were tested. The data indicate the basic trends in the mechanical properties of the coatings over a wide range of isothermal conditions. Some of the trends are correlated with material density.

  8. Mechanical properties testing and results for thermal barrier coatings

    Science.gov (United States)

    Cruse, Thomas A.; Johnsen, B. P.; Nagy, Andrew

    1995-01-01

    The paper reports on several years of mechanical testing of thermal barrier coatings. The test results were generated to support the development of durability models for the coatings in heat engine applications. The test data that are reviewed include modulus, static strength, and fatigue strength data. The test methods and results are discussed, along with the significant difficulties inherent in mechanical testing of thermal barrier coating materials. The materials include 7 percent wt. and 8 percent wt. yttria, partially stabilized zirconia as well as a cermet material. Both low pressure plasma spray and electron-beam physical vapor deposited coatings were tested. The data indicate the basic trends in the mechanical properties of the coatings over a wide range of isothermal conditions. Some of the trends are correlated with material density.

  9. Physical and chemical test results of electrostatic safe flooring materials

    Science.gov (United States)

    Gompf, R. H.

    1988-01-01

    This test program was initiated because a need existed at the Kennedy Space Center (KSC) to have this information readily available to the engineer who must make the choice of which electrostatic safe floor to use in a specific application. The information, however, should be of value throughout both the government and private industry in the selection of a floor covering material. Included are the test results of 18 floor covering materials which by test evaluation at KSC are considered electrostatically safe. Tests were done and/or the data compiled in the following areas: electrostatics, flammability, hypergolic compatibility, outgassing, floor type, material thickness, and available colors. Each section contains the test method used to gather the data and the test results.

  10. Colorectal Tumour Microsatellite Instability Test Results: Perspectives from Patients

    Directory of Open Access Journals (Sweden)

    Lindor Noralane M

    2004-05-01

    Full Text Available Abstract Purpose To determine which individuals with colorectal cancer (CRC were interested in knowing the results of their tumour microsatellite instability (MSI and immunohistochemistry (IHC testing. We were also interested in the patients' reasons for choosing to learn their results and in the impact of those results on overall self-assessed quality of life. Patients and Methods CRCs from 414 individuals were assayed for MSI and IHC for DNA mismatch repair gene products (MLH1, MSH2, MSH6. Individuals were invited to learn their MSI/IHC results. They randomly received either brief or extended educational materials about the testing and a pretest survey to learn reasons for their interest and to assess their pretest quality of life. Results Of the 414 individuals, 307 (74% chose to learn their results. There was no significant difference in interest in knowing test results according to gender, age, educational level, or family history of colon cancer. The level of detail in the information piece received by the patients did not influence their desire to know their test results. Self-assessed quality of life was not altered by receiving results and was not correlated with the test outcome. Conclusions Individuals with colorectal cancer had a high level of interest in learning their individual MSI/IHC test results and did not seem deterred by the inherent complexity or ambiguity of this information. Regardless of test outcome, results did not significantly affect self-assessed quality of life. Further studies are needed to assess comprehension of results and behavioural changes resulting from the learning of MSI/IHC results.

  11. Development and Results of a First Generation Least Expensive Approach to Fission: Module Tests and Results

    Science.gov (United States)

    Houts, Mike; Godfroy, Tom; Pederson, Kevin; Sena, J. Tom; VanDyke, Melissa; Dickens, Ricky; Reid, Bob J.; Martin, Jim

    2000-01-01

    The use of resistance heaters to simulate heat from fission allows extensive development of fission systems to be performed in non-nuclear test facilities, saving time and money. Resistance heated tests on the Module Unfueled Thermal-hydraulic Test (MUTT) article has been performed at the Marshall Space Flight Center. This paper discusses the results of these experiments and identifies future tests to be performed.

  12. Supervised Self-Organizing Classification of Superresolution ISAR Images: An Anechoic Chamber Experiment

    Science.gov (United States)

    Radoi, Emanuel; Quinquis, André; Totir, Felix

    2006-12-01

    The problem of the automatic classification of superresolution ISAR images is addressed in the paper. We describe an anechoic chamber experiment involving ten-scale-reduced aircraft models. The radar images of these targets are reconstructed using MUSIC-2D (multiple signal classification) method coupled with two additional processing steps: phase unwrapping and symmetry enhancement. A feature vector is then proposed including Fourier descriptors and moment invariants, which are calculated from the target shape and the scattering center distribution extracted from each reconstructed image. The classification is finally performed by a new self-organizing neural network called SART (supervised ART), which is compared to two standard classifiers, MLP (multilayer perceptron) and fuzzy KNN ([InlineEquation not available: see fulltext.] nearest neighbors). While the classification accuracy is similar, SART is shown to outperform the two other classifiers in terms of training speed and classification speed, especially for large databases. It is also easier to use since it does not require any input parameter related to its structure.

  13. Supervised Self-Organizing Classification of Superresolution ISAR Images: An Anechoic Chamber Experiment

    Directory of Open Access Journals (Sweden)

    Radoi Emanuel

    2006-01-01

    Full Text Available The problem of the automatic classification of superresolution ISAR images is addressed in the paper. We describe an anechoic chamber experiment involving ten-scale-reduced aircraft models. The radar images of these targets are reconstructed using MUSIC-2D (multiple signal classification method coupled with two additional processing steps: phase unwrapping and symmetry enhancement. A feature vector is then proposed including Fourier descriptors and moment invariants, which are calculated from the target shape and the scattering center distribution extracted from each reconstructed image. The classification is finally performed by a new self-organizing neural network called SART (supervised ART, which is compared to two standard classifiers, MLP (multilayer perceptron and fuzzy KNN ( nearest neighbors. While the classification accuracy is similar, SART is shown to outperform the two other classifiers in terms of training speed and classification speed, especially for large databases. It is also easier to use since it does not require any input parameter related to its structure.

  14. Is the frequent sonographic anechoic area distally in metacarpophalangeal joints a sign of arthritis?

    Science.gov (United States)

    Ten Cate, David Folkert; Luime, Jolanda Jacoba; Hazes, Johanna Maria Wilhelmina; Kleinrensink, Gerrit-Jan; Jacobs, Johannes Wilhelmus Gerardus

    2014-10-01

    In clinical practice, ultrasonography (US) often reveals, in the dorsal scan, a small anechoic area distally in both inflamed and clinically non-inflamed metacarpophalangeal joints. This "distal anechogenicity in the metacarpophalangeal joint" (DAEM) might thus be scored false positively as arthritis. We aimed to investigate whether the DAEM is a sign of arthritis. We evaluated the prevalence of DAEMs in 24 non-arthritic subjects. We then compared the dimensions of the DAEM in 10 non-arthritic subjects with a DAEM and 7 consecutive rheumatoid arthritis (RA) outpatients, using 2-D and 3-D ultrasound. Furthermore, we dissected two fresh-frozen postmortem hand specimens after US. A DAEM was observed in the metacarpophalangeal 2 (MCP2) joints of 54% of the 24 non-selected non-arthritic individuals; in none of those did the joint exhibit a power Doppler signal. A DAEM was observed in 86% of the 7 RA patients. Dimensions of DAEMs did not statistically significantly differ between these groups. At 3-D imaging and dissection, the DAEM was found to be an extension of the metacarpophalangeal joint capsule. In conclusion, DAEMs occur frequently and are not a sign of arthritis, but are distal joint recesses. This should be taken into account when using current sensitive ultrasonographic scoring systems grading arthritis.

  15. Finite Element Analysis and Test Results Comparison for the Hybrid Wing Body Center Section Test Article

    Science.gov (United States)

    Przekop, Adam; Jegley, Dawn C.; Rouse, Marshall; Lovejoy, Andrew E.

    2016-01-01

    This report documents the comparison of test measurements and predictive finite element analysis results for a hybrid wing body center section test article. The testing and analysis efforts were part of the Airframe Technology subproject within the NASA Environmentally Responsible Aviation project. Test results include full field displacement measurements obtained from digital image correlation systems and discrete strain measurements obtained using both unidirectional and rosette resistive gauges. Most significant results are presented for the critical five load cases exercised during the test. Final test to failure after inflicting severe damage to the test article is also documented. Overall, good comparison between predicted and actual behavior of the test article is found.

  16. Results of EMC market surveillance tests for UPS systems

    Energy Technology Data Exchange (ETDEWEB)

    Rajamaeki, J. [Safety Technology Authority, Helsinki (Finland)

    1997-12-31

    This paper reports the first wide electromagnetic compatibility (EMC) market surveillance project in Finland in which the uninterruptible power systems (UPS) on the Finnish market are monitored. Altogether 11 UPS units are EMC tested and the results of these tests are described in this paper. The effect of basic characters of UPS on the level of electromagnetic interference are analysed. (orig.) 3 refs.

  17. Preliminary results of steel containment vessel model test

    Energy Technology Data Exchange (ETDEWEB)

    Luk, V.K.; Hessheimer, M.F. [Sandia National Labs., Albuquerque, NM (United States); Matsumoto, T.; Komine, K.; Arai, S. [Nuclear Power Engineering Corp., Tokyo (Japan); Costello, J.F. [Nuclear Regulatory Commission, Washington, DC (United States)

    1998-04-01

    A high pressure test of a mixed-scaled model (1:10 in geometry and 1:4 in shell thickness) of a steel containment vessel (SCV), representing an improved boiling water reactor (BWR) Mark II containment, was conducted on December 11--12, 1996 at Sandia National Laboratories. This paper describes the preliminary results of the high pressure test. In addition, the preliminary post-test measurement data and the preliminary comparison of test data with pretest analysis predictions are also presented.

  18. Calibration of Results of Water Meter Test Facility

    OpenAIRE

    Andrius Bončkus; Gediminas Gediminas

    2011-01-01

    The results of water meter test facility calibration are presented. More than 30 test facilities are used in Lithuania nowadays. All of them are certificated for water meter of class 2 verification. The results of inter-laboratory comparison of multi-jet water meter calibration at flow rate Q = 5 m3/h are presented. Lithuanian Energy Institute was appointed as reference laboratory for the comparison. Twelve water meter verification and calibration laboratories from Lithuania participated in t...

  19. Results from the Astronomy Diagnostic Test National Project

    Science.gov (United States)

    Deming, G. L.

    2001-12-01

    During 2000 and 2001, the validity and reliability of the Astronomy Diagnostic Test Version 2.0 (ADT 2.0) were formally investigated through the Astronomy Diagnostic Test National Project. The ADT 2.0 was administered as a pre-test to 5346 students and as a post-test to 3842 students. Student test results were collected from 97 classes that ranged in size from 4 to 320 students with 30 states represented. The 68 professors participating in the ADT National Project taught classes at universities (54%), 4-year colleges (27%), and 2-year colleges (19%). The database was analyzed for reliability at the Ontario Institute for Studies in Education. A pre-test value for Cronbach's alpha of 0.65 and post-test value of 0.76 demonstrate an acceptable degree of internal consistency. The average score for the 44 participating professors who completed the ADT as experts was 98%. Face and content validity were established by combining results from the experts with feedback from 60 student interviews. Student results from the National Project yielded an average score of 32.4% for the pre-test and 47.3% for the post-test. There is a gender discrepancy in favor of males that persists in both the pre-test (11% points) and the post-test (12% points) scores. The variations across geographic distribution and institution types were not significant. In addition to the 21 content items, the ADT 2.0 has 12 student background questions enabling instructors to have a better understanding of who takes introductory astronomy. This research was supported by the National Science Foundation through grants REC-0089239 (GD) and DGE-9714489 (BH).

  20. A report on the psychological test results of battering parents.

    Science.gov (United States)

    Hyman, C A

    1977-09-01

    The short form of the Wechsler Adult Intelligence Scale and Cattell's 16PF test have been given to patients attending the National Advisory Centre on the Battered Child (NSPCC) and in the case of the personality questionnaire the results compared to non-battering control adults' scores. The intelligence levels of battering parents conform to normal expectation although there is a non-significant trend to marginally lower than normal results especially in verbal tests. The 16PF test reveals immature impetuosity on the part of the mothers as a main finding and introversion in the fathers. The relevance of these findings to battering is discussed.

  1. Uprated OMS Engine Status-Sea Level Testing Results

    Science.gov (United States)

    Bertolino, J. D.; Boyd, W. C.

    1990-01-01

    The current Space Shuttle Orbital Maneuvering Engine (OME) is pressure fed, utilizing storable propellants. Performance uprating of this engine, through the use of a gas generator driven turbopump to increase operating pressure, is being pursued by the NASA Johnson Space Center (JSC). Component level design, fabrication, and test activities for this engine system have been on-going since 1984. More recently, a complete engine designated the Integrated Component Test Bed (ICTB), was tested at sea level conditions by Aerojet. A description of the test hardware and results of the sea level test program are presented. These results, which include the test condition operating envelope and projected performance at altitude conditions, confirm the capability of the selected Uprated OME (UOME) configuration to meet or exceed performance and operational requirements. Engine flexibility, demonstrated through testing at two different operational mixture ratios, along with a summary of projected Space Shuttle performance enhancements using the UOME, are discussed. Planned future activities, including ICTB tests at simulated altitude conditions, and recommendations for further engine development, are also discussed.

  2. Assessment of Galileo modal test results for mathematical model verification

    Science.gov (United States)

    Trubert, M.

    1984-01-01

    The modal test program for the Galileo Spacecraft was completed at the Jet Propulsion Laboratory in the summer of 1983. The multiple sine dwell method was used for the baseline test. The Galileo Spacecraft is a rather complex 2433 kg structure made of a central core on which seven major appendages representing 30 percent of the total mass are attached, resulting in a high modal density structure. The test revealed a strong nonlinearity in several major modes. This nonlinearity discovered in the course of the test necessitated running additional tests at the unusually high response levels of up to about 21 g. The high levels of response were required to obtain a model verification valid at the level of loads for which the spacecraft was designed. Because of the high modal density and the nonlinearity, correlation between the dynamic mathematical model and the test results becomes a difficult task. Significant changes in the pre-test analytical model are necessary to establish confidence in the upgraded analytical model used for the final load verification. This verification, using a test verified model, is required by NASA to fly the Galileo Spacecraft on the Shuttle/Centaur launch vehicle in 1986.

  3. Measurement of ability emotional intelligence: results for two new tests.

    Science.gov (United States)

    Austin, Elizabeth J

    2010-08-01

    Emotional intelligence (EI) has attracted considerable interest amongst both individual differences researchers and those in other areas of psychology who are interested in how EI relates to criteria such as well-being and career success. Both trait (self-report) and ability EI measures have been developed; the focus of this paper is on ability EI. The associations of two new ability EI tests with psychometric intelligence, emotion perception, and the Mayer-Salovey-Caruso EI test (MSCEIT) were examined. The new EI tests were the Situational Test of Emotion Management (STEM) and the Situational Test of Emotional Understanding (STEU). Only the STEU and the MSCEIT Understanding Emotions branch were significantly correlated with psychometric intelligence, suggesting that only understanding emotions can be regarded as a candidate new intelligence component. These understanding emotions tests were also positively correlated with emotion perception tests, and STEM and STEU scores were positively correlated with MSCEIT total score and most branch scores. Neither the STEM nor the STEU were significantly correlated with trait EI tests, confirming the distinctness of trait and ability EI. Taking the present results as a starting-point, approaches to the development of new ability EI tests and models of EI are suggested.

  4. Changes over time in milk test results following pancreatectomy

    Institute of Scientific and Technical Information of China (English)

    Hideki Aoki; Masashi Utsumi; Kenta Sui; Nobuhiko Kanaya; Tomoyoshi Kunitomo; Hitoshi Takeuchi; Norihisa Takakura; Shigehiro Shiozaki; Hiroyoshi Matsukawa

    2016-01-01

    AIM: To investigate changes over time in, and effects of sealing technology on, milk test results following pancreatectomy. METHODS: From April 2008 to October 2013, 66 pancreatic resections were performed at the Iwakuni Clinical Center. The milk test has been routinely conducted at the institute whenever possible during pancreatectomy. The milk test comprises the following procedure: A nasogastric tube is inserted until the third portion of the duodenum, followed by injection of 100 mL of milk through the tube. If a chyle leak is present, the patient tests positive in this milk test based on the observation of a white milky discharge. Positive milk test rates, leakage sites, and chylous ascites incidence were examined. Liga Sure?(LS; Covidien, Dublin, Ireland), a vessel-sealing device, is routinely used in pancreatectomy. Positive milk test rates before and after use of LS, as well as drain discharge volume at the 2nd and 3rd postoperative days, were compared retrospectively. Finally, positive milk test rates and chylous ascites incidence were compared with the results of a previous report.RESULTS: Fifty-nine milk tests were conducted during pancreatectomy. The positive milk test rate for all pancreatectomy cases was 13.6%(8 of 59 cases). One case developed postoperative chylous ascites(2.1% among the pancreatoduedenectomy cases and 1.7% among all pancreatectomies). Positive rates by procedure were 12.8% for pancreatoduodenectomy and 22.2% for distal pancreatectomy. Positive rates by disease were 17.9% for pancreatic and 5.9% for biliary diseases. When comparing results from before and after use of LS, positive milk test rates in pancreatoduodenectomy were 13.0% before and 12.5% after, while those in distal pancreatectomy were 33.3% and 0%. Drainage volume tended to decrease when LS was used on the 3rd postoperative day(volumes were 424 ± 303 mL before LS and 285 ± 185 mL after, P = 0.056). Both chylous ascites incidence and positive milk test

  5. Testing Result Statistics-Based Rapid Testing Method for Safety-Critical System

    Institute of Scientific and Technical Information of China (English)

    Zhi-Yao Deng; Nan Sang

    2008-01-01

    Safety-critical system (SCS) has highly demand for dependability, which requires plenty of resource to ensure that the system under test (SUT) satisfies the dependability requirement. In this paper, a new SCS rapid testing method is proposed to improve SCS adaptive dependability testing. The result of each test execution is saved in calculation memory unit and evaluated as an algorithm model. Then the least quantity of scenario test case for next test execution will be calculated according to the promised SUT's confidence level. The feedback data are generated to weight controller as the guideline for the further testing. Finally, a compre- hensive experiment study demonstrates that this adaptive testing method can really work in practice. This rapid testing method, testing result statistics-based adaptive control, makes the SCS dependability testing much more effective.

  6. TEG® and ROTEM® in trauma: similar test but different results?

    Directory of Open Access Journals (Sweden)

    Sankarankutty Ajith

    2012-08-01

    Full Text Available Abstract Introduction Transfusion in trauma is often empiric or based on traditional lab tests. Viscoelastic tests such as thromboelastography (TEG® and rotational thromboelastometry (ROTEM® have been proposed as superior to traditional lab tests. Due to the similarities between the two tests, general opinion seems to consider them equivalent with interchangeable interpretations. However, it is not clear whether the results can be similarly interpreted. This review evaluates the comparability between TEG and ROTEM and performs a descriptive review of the parameters utilized in each test in adult trauma patients. Methods PUBMED database was reviewed using the keywords “thromboelastography” and “compare”, between 2000 and 2011. Original studies directly comparing TEG® with ROTEM® in any area were retrieved. To verify the individual test parameter used in studies involving trauma patients, we further performed a review using the keywords “thromboelastography” and “trauma” in the PUBMED database. Results Only 4 studies directly compared TEG® with ROTEM®. One in liver transplantation found that transfusion practice could differ depending on the device in use. Another in cardiac surgery concluded that all measurements are not completely interchangeable. The third article using commercially available plasma detected clinically significant differences in the results from the two devices. The fourth one was a head-to-head comparison of the technical aspects. The 24 articles reporting the use of viscoelastic tests in trauma patients, presented considerable heterogeneity. Conclusion Both tests are potentially useful as means to rapidly diagnose coagulopathy, guide transfusion and determine outcome in trauma patients. Differences in the activators utilized in each device limit the direct comparability. Standardization and robust clinical trials comparing the two technologies are needed before these tests can be widely recommended for

  7. Tensile and fracture toughness test results of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Chaouadi, R.; Moons, F.; Puzzolante, J.L. [Centre d`Etude de l`Energie Nucleaire, Mol (Belgium)

    1998-01-01

    Tensile and fracture toughness test results of four Beryllium grades are reported here. The flow and fracture properties are investigated by using small size tensile and round compact tension specimens. Irradiation was performed at the BR2 material testing reactor which allows various temperature and irradiation conditions. The fast neutron fluence (>1 MeV) ranges between 0.65 and 2.45 10{sup 21} n/cm{sup 2}. In the meantime, un-irradiated specimens were aged at the irradiation temperatures to separate if any the effect of temperature from irradiation damage. Test results are analyzed and discussed, in particular in terms of the effects of material grade, test temperature, thermal ageing and neutron irradiation. (author)

  8. COMPARISON OF RESULTS OF THERMAL TESTS OF BALCONY DOORS

    Directory of Open Access Journals (Sweden)

    Golubev Stanislav Sergeevich

    2012-10-01

    Full Text Available Results of thermal tests of balcony doors are presented in the article. In the course of the research project, two types of doors were tested. The first type represents a PVC frame door (width 82 mm; it has a triple glazing (4K-16Ar-4-16Ar-K4; its blank part represents a polystyrene sandwich panel (width 40 mm. The second type represents a PVC frame door (width 82 mm, that has a triple glazing (4K-16Ar-4-16Ar-K4 and composite PVC panels. The testing procedure and processing results are described in the article. The test has demonstrated that the thermal resistance value of the balcony door of the first type exceeds the thermal resistance value of the balcony door of the second type.

  9. Steel Containment Vessel Model Test: Results and Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Costello, J.F.; Hashimote, T.; Hessheimer, M.F.; Luk, V.K.

    1999-03-01

    A high pressure test of the steel containment vessel (SCV) model was conducted on December 11-12, 1996 at Sandia National Laboratories, Albuquerque, NM, USA. The test model is a mixed-scaled model (1:10 in geometry and 1:4 in shell thickness) of an improved Mark II boiling water reactor (BWR) containment. A concentric steel contact structure (CS), installed over the SCV model and separated at a nominally uniform distance from it, provided a simplified representation of a reactor shield building in the actual plant. The SCV model and contact structure were instrumented with strain gages and displacement transducers to record the deformation behavior of the SCV model during the high pressure test. This paper summarizes the conduct and the results of the high pressure test and discusses the posttest metallurgical evaluation results on specimens removed from the SCV model.

  10. Proposed Interventions to Decrease the Frequency of Missed Test Results

    Science.gov (United States)

    Wahls, Terry L.; Cram, Peter

    2009-01-01

    Numerous studies have identified that delays in diagnosis related to the mishandling of abnormal test results are an import contributor to diagnostic errors. Factors contributing to missed results included organizational factors, provider factors and patient-related factors. At the diagnosis error conference continuing medical education conference…

  11. RF Test Results from Cryomodule 1 at the Fermilab SRF Beam Test Facility

    CERN Document Server

    Harms, E; Chase, B; Cullerton, E; Hocker, A; Jensen, C; Joireman, P; Klebaner, A; Kubicki, T; Kucera, M; Legan, A; Leibfritz, J; Martinez, A; McGee, M; Nagaitsev, S; Nezhevenko, O; Nicklaus, D; Pfeffer, H; Pischalnikov, Y; Prieto, P; Reid, J; Schappert, W; Tupikov, V; Varghese, P; Branlard, J

    2012-01-01

    Powered operation of Cryomodule 1 (CM-1) at the Fermilab SRF Beam Test Facility began in late 2010. Since then a series of tests first on the eight individual cavities and then the full cryomodule have been performed. We report on the results of these tests and lessons learned which will have an impact on future module testing at Fermilab.

  12. Cold vacuum drying proof of performance (first article testing) test results

    Energy Technology Data Exchange (ETDEWEB)

    MCCRACKEN, K.J.

    1999-06-23

    This report presents and details the test results of the first of a kind process referred to as Cold Vacuum Drying (CVD). The test results are compiled from several months of testing of the first process equipment skid and ancillary components to de-water and dry Multi-Canister Overpacks (MCO) filled with Spent Nuclear Fuel (SNF). The tests results provide design verifications, equipment validations, model validation data, and establish process parameters.

  13. Physical separations soil washing system cold test results

    Energy Technology Data Exchange (ETDEWEB)

    McGuire, J.P.

    1993-07-28

    This test summary describes the objectives, methodology, and results of a physical separations soil-washing system setup and shakedown test using uncontaminated soil. The test is being conducted in preparation for a treatability test to be conducted in the North Pond of the 300-FF-1 Operable Unit. It will be used to assess the feasibility of using a physical separations process to reduce the volume of contaminated soils in the 300-FF-1 Operable Unit. The test is described in DOE-RL (1993). The setup test was conducted at an uncontrolled area located approximately 3.2 km northwest of the 300-FF-1 Operable Unit. The material processed was free of contamination. The physical separation equipment to be used in the test was transferred to the US Department of Energy (DOE) by the US Environmental Protection Agency (EPA) Risk Reduction Engineering Laboratory. On May 13, 1993, soil-washing equipment was moved to the cold test location. Design assistance and recommendation for operation was provided by the EPA.

  14. Thermal Analysis of Low Layer Density Multilayer Insulation Test Results

    Science.gov (United States)

    Johnson, Wesley L.

    2011-01-01

    Investigation of the thermal performance of low layer density multilayer insulations is important for designing long-duration space exploration missions involving the storage of cryogenic propellants. Theoretical calculations show an analytical optimal layer density, as widely reported in the literature. However, the appropriate test data by which to evaluate these calculations have been only recently obtained. As part of a recent research project, NASA procured several multilayer insulation test coupons for calorimeter testing. These coupons were configured to allow for the layer density to be varied from 0.5 to 2.6 layer/mm. The coupon testing was completed using the cylindrical Cryostat-l00 apparatus by the Cryogenics Test Laboratory at Kennedy Space Center. The results show the properties of the insulation as a function of layer density for multiple points. Overlaying these new results with data from the literature reveals a minimum layer density; however, the value is higher than predicted. Additionally, the data show that the transition region between high vacuum and no vacuum is dependent on the spacing of the reflective layers. Historically this spacing has not been taken into account as thermal performance was calculated as a function of pressure and temperature only; however the recent testing shows that the data is dependent on the Knudsen number which takes into account pressure, temperature, and layer spacing. These results aid in the understanding of the performance parameters of MLI and help to complete the body of literature on the topic.

  15. Patch Test Results in Patients with Allergic Contact Dermatitis / Mucositis

    Directory of Open Access Journals (Sweden)

    Özlem Su

    2008-05-01

    Full Text Available Background and Design: The aims of our study were to determine the frequency of positive patch reactions and the most common allergens in patients with allergic contact dermatitis (ACD and/or mucositis(M who underwent with T.R.U.E. “Thin-layer Rapid-Use Epicutaneous” test and evaluate supplemantal series used with T.R.U.E. test effect on patch test results.Material and Method: In this study 161 ACD, 5 ACM, 1 ACD and ACM were enrolled. While 139 of all patients were patch tested with T.R.U.E. test alone,out of 28 patients were tested for T.R.U.E. test and also with supplemental series that included textile colours (9 of tested patients, plastic and glues (9, dental screening (6, backery (2, cosmetic (1 and plastic and glues and dental screening (1. Supplemental series were chosen according to patient’s occupation and clinic presentation. The data from our patients were analyzed as percentage. The relationship between contact sensitization and atopic status was evaluated with Yate’s correlation x2 test.Results: Eighty-six male, 81 female were taken into this study. The median age was 36.5.While 25.9% of 139 patients tested with T.R.U.E. test alone,46.4% of 28 patients applied supplemental series in addition to T.R.U.E. test showed positive reaction to one or more allergens. The most common allergens were nickel sulphate (14.4%, potassium dichromate (4.8%, fragrance mix (2.9% and colophony (2.9%. The most common supplemental allergens were octil gallat (50% in bakery and copper sulphate, goldsodiumthiosulphate (42.8% in dental screening. Positive patch reactions were detected 83.3% in 6 patients with AKM, 80% of these positive reactions was againts dental screening. The rate of contact sensitization between atopics and non-atopics was not significant (p>0.05. Conclusion: We suggest in presence of mucositis and/or occupational dermatoses using supplemental series in addition to T.R.U.E. test would be more beneficial in identifing the

  16. Evaluation of the screening test results before marriage

    Directory of Open Access Journals (Sweden)

    Süleyman Durmaz

    2011-09-01

    Full Text Available Objectives: Human immunodeficiency virus (HIV, Hepatitis B and Hepatitis C viruses and Treponema pallidum are parenterally and sexually transmitted infection agents. Screening test is made before marriage to pre-marital couples legally under the relevant legislation and legal procedures in our country; applicants are evaluated in terms of sexually transmitted diseases. The aim of this study is to evaluate pre-marital test results for HBsAg, anti-HCV, anti-HIV I/II and Treponema pallidum.Materials and methods: To make screening test before marriage, randomized 117 patients who were applied to Kızıltepe General Hospital of Infectious Diseases and Clinical Microbiology, were included in this study between January 2011 and March 2011. Of these patients, 64 were women (average age 24.7±5.7, and 55 were males (mean age 24.7±4.7. HBsAg, anti-HCV and anti-HIV I/II tests of the patients were studied by macro-ELISA device (ECIQ Vitros, Ortho Clinical Diagnostics, USA, screening of anti-Treponema pallidum IgG, IgA and IgM antibodies were studied by immunochromatographic rapid test (syphilis syphilis 3.0, Standard Diagnostics, inc. Korea.Results: Of the 119 patients, five patients (4.2% were positive for HBsAg (3 male and 2 female. Anti-HCV, anti-HIV I/II and anti-Treponema pallidum antibodies were negative in all patients.Conclusion: HBsAg test result which was obtained in present study has been found consistent with HBsAg positivity rate in our region. As a result of screening test that was done before marriage will continue to believe that the increased importance of the prevention of sexually transmitted diseases. J Clin Exp Invest 2011; 2 (3: 292-294.

  17. Small-Scale Spray Releases: Initial Aerosol Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, Lenna A.; Gauglitz, Phillip A.; Kimura, Marcia L.; Brown, Garrett N.; Kurath, Dean E.; Buchmiller, William C.; Smith, Dennese M.; Blanchard, Jeremy; Song, Chen; Daniel, Richard C.; Wells, Beric E.; Tran, Diana N.; Burns, Carolyn A.

    2013-05-29

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. Two key technical areas were identified where testing results were needed to improve the technical basis by reducing the uncertainty due to extrapolating existing literature results. The first technical need was to quantify the role of slurry particles in small breaches where the slurry particles may plug and result in substantially reduced, or even negligible, respirable fraction formed by high-pressure sprays. The second technical need was to determine the aerosol droplet size distribution and volume from prototypic breaches and fluids, specifically including sprays from larger breaches with slurries where data from the literature are scarce. To address these technical areas, small- and large-scale test stands were constructed and operated with simulants to determine aerosol release fractions and net generation rates from a range of breach sizes and geometries. The properties of the simulants represented the range of properties expected in the WTP process streams and included water, sodium salt solutions, slurries containing boehmite or gibbsite, and a hazardous chemical simulant. The effect of antifoam agents was assessed with most of the simulants. Orifices included round holes and

  18. Calibration of Results of Water Meter Test Facility

    Directory of Open Access Journals (Sweden)

    Andrius Bončkus

    2011-04-01

    Full Text Available The results of water meter test facility calibration are presented. More than 30 test facilities are used in Lithuania nowadays. All of them are certificated for water meter of class 2 verification. The results of inter-laboratory comparison of multi-jet water meter calibration at flow rate Q = 5 m3/h are presented. Lithuanian Energy Institute was appointed as reference laboratory for the comparison. Twelve water meter verification and calibration laboratories from Lithuania participated in the ILC. The deviations from reference values were described by the normalized deviation En.Article in Lithuanian

  19. Healthy Efficient New Gas Homes (HENGH) Pilot Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Chan, Wanyu R. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Maddalena, Randy L [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Stratton, Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Hotchi, Toshifumi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Singer, Brett C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Walker, Iain S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sherman, Max H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2016-05-01

    The Healthy Efficient New Gas Homes (HENGH) is a field study that will collect data on ventilation systems and indoor air quality (IAQ) in new California homes that were built to 2008 Title 24 standards. A pilot test was performed to help inform the most time and cost effective approaches to measuring IAQ in the 100 test homes that will be recruited for this study. Two occupied, single-family detached homes built to 2008 Title 24 participated in the pilot test. One of the test homes uses exhaust-only ventilation provided by a continuous exhaust fan in the laundry room. The other home uses supply air for ventilation. Measurements of IAQ were collected for two weeks. Time-resolved concentrations of particulate matter (PM), nitrogen dioxide (NO2), carbon dioxide (CO2), carbon monoxide (CO), and formaldehyde were measured. Measurements of IAQ also included time-integrated concentrations of volatile organic compounds (VOCs), volatile aldehydes, and NO2. Three perfluorocarbon tracers (PFTs) were used to estimate the dilution rate of an indoor emitted air contaminant in the two pilot test homes. Diagnostic tests were performed to measure envelope air leakage, duct leakage, and airflow of range hood, exhaust fans, and clothes dryer vent when accessible. Occupant activities, such as cooking, use of range hood and exhaust fans, were monitored using various data loggers. This document describes results of the pilot test.

  20. Planar Pixel Sensors for the ATLAS Upgrade: Beam Tests results

    CERN Document Server

    Weingarten, J; Beimforde, M; Benoit, M; Bomben, M; Calderini, G; Gallrapp, C; George, M; Gibson, S; Grinstein, S; Janoska, Z; Jentzsch, J; Jinnouchi, O; Kishida, T; La Rosa, A; Libov, V; Macchiolo, A; Marchiori, G; Münstermann, D; Nagai, R; Piacquadio, G; Ristic, B; Rubinskiy, I; Rummler, A; Takubo, Y; Troska, G; Tsiskaridtze, S; Tsurin, I; Unno, Y; Weigel, P; Wittig, T

    2012-01-01

    Results of beam tests with planar silicon pixel sensors aimed towards the ATLAS Insertable B-Layer and High Luminosity LHC (HL-LHC) upgrades are presented. Measurements include spatial resolution, charge collection performance and charge sharing between neighbouring cells as a function of track incidence angle for different bulk materials. Measurements of n-in-n pixel sensors are presented as a function of fluence for different irradiations. Furthermore p-type silicon sensors from several vendors with slightly differing layouts were tested. All tested sensors were connected by bump-bonding to the ATLAS Pixel read-out chip. We show that both n-type and p-type tested planar sensors are able to collect significant charge even after integrated fluences expected at HL-LHC.

  1. Test results on silicon micro-strip detectors for ATLAS

    Energy Technology Data Exchange (ETDEWEB)

    DeWitt, J.; Dorfan, D.E.; Dubbs, T.; Grillo, A.A.; Kashigin, S.; Kroeger, W.; Pulliam, T.; Rahn, J.; Rowe, W.A.; Sadrozinski, H.F.-W.; Seiden, A.; Spencer, E.; Webster, A.; Wichmann, R.; Wilder, M.; Williams, D.C.; Dane, J.; Lankford, A.; Pier, S.; Schmid, B.; Bonino, R.; Couyoumtzelis, C.; Demierre, P.; Fujita, K.; Handa, T.; Iwata, Y.; Ohsugi, T.; Iwasaki, H.; Kohriki, T.; Kondo, T.; Terada, S.; Unno, Y.; Takashima, R.; Ciocio, A.; Collins, T.; Emes, J.; Gilchriese, M.G.D.; Haber, C.; Kipnis, I.; Shapiro, M.; Siegrist, J.; Spieler, H.; Moorhead, G.; Nakao, M.; Tamura, N.; Dabrowski, W.; Idzik, M.; Godlewski, J.; Grewal, A.; Nickerson, R.; Wastie, R.; Gao, Y.; Gonzalez, S.; Walsh, A.M.; Feng, Z. [California Univ., Santa Cruz, CA (United States). Inst. for Particle Phys.]|[California Univ., Irvine, CA (United States)]|[Geneva Univ. (Switzerland)]|[Hiroshima Univ. (Japan)]|[KEK, Tsukuba (Japan)]|[Kyoto Univ. Education (Japan)]|[Lawrence Berkeley National Lab., CA (United States)]|[Melbourne Univ. (Australia)]|[Okayama Univ. (Japan)]|[IPNT, Krakow (Poland)]|[INP, Krakow (Poland)]|[Oxford Univ. (United Kingdom)]|[Wisconsin Univ., Madison, WI (United States)

    1997-02-11

    We report results from beam tests on silicon microstrip detectors using a binary readout system for ATLAS. The data were collected during the H8 beam test at CERN in August/September 1995 and the KEK test in February 1996. The binary modules tested had been assembled from silicon microstrip detectors of different layout and from front-end electronics chips of different architecture. The efficiency, noise occupancy and position resolution were determined as a function of the threshold setting for various bias voltages and angles of incidence for both irradiated and non-irradiated detectors. In particular, the high spatial resolution of the beam telescope allowed the evaluation of the performance as a function of the track location in between detector strips. (orig.).

  2. Selected Test Results from the Encell Technology Nickel Iron Battery

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Summer Kamal Rhodes [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Advanced Power Sources R& D; Baca, Wes Edmund [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Advanced Power Sources R& D; Avedikian, Kristan [Encell Technology, Alachua, FL (United States)

    2014-09-01

    The performance of the Encell Nickel Iron (NiFe) battery was measured. Tests included capacity, capacity as a function of rate, capacity as a function of temperature, charge retention (28-day), efficiency, accelerated life projection, and water refill evaluation. The goal of this work was to evaluate the general performance of the Encell NiFe battery technology for stationary applications and demonstrate the chemistry's capabilities in extreme conditions. Test results have indicated that the Encell NiFe battery technology can provide power levels up to the 6C discharge rate, ampere-hour efficiency above 70%. In summary, the Encell batteries have met performance metrics established by the manufacturer. Long-term cycle tests are not included in this report. A cycle test at elevated temperature was run, funded by the manufacturer, which Encell uses to predict long-term cycling performance, and which passed their prescribed metrics.

  3. PFR fuel cladding transient test results and analysis

    Science.gov (United States)

    Cannon, N. S.; Hunter, C. W.; Kear, K. L.; Wood, M. H.

    1986-05-01

    Fuel Cladding Transient Tests (FCTT) were performed on M316 cladding specimens obtained from mixed-oxide fuel pins irradiated in the Prototype Fast Reactor (PFR) to burnups of 4 and 9 atom percent. In these tests, specimens of fuel cladding were pressurized and heated until failure occurred. Samples of cladding from PFR fuel pins exhibited generally greater strength and ductility than specimens from Experimental Breeder Reactor-II (EBR-II) mixed-oxide fuel pins tested under similar conditions. Apparently, the PFR cladding properties were not degraded by a fuel adjacency effect (FAE) observed in fuel pin cladding from EBR-II irradiations. A recently developed model of grain boundary cavity growth was used to predict the results of the tests conducted on PFR cladding. It was found that the predicted failure temperatures for the relevant internal pressures were in good agreement with experimental failure temperatures.

  4. Suit Port Aft Bulkhead Mockup 2008 Test Results

    Science.gov (United States)

    Romig, Barbara A.; Allton, Charles S.; Litaker, Harry L.

    2009-01-01

    The Lunar Electric Rover (LER), formerly called the Small Pressurized Rover (SPR), is currently being carried as an integral part of the current Lunar Surface Architectures under consideration in the Constellation program. One element of the LER is the suit port, the means by which the crew performs Extravehicular Activities (EVAs). Two suit port deliverables were produced in fiscal year 2008: an aft bulkhead mockup for functional integrated testing with the 1-G LER mockup and a functional and pressurizable Engineering Unit (EU). This paper focuses on the aft bulkhead mockup test results from Desert Research and Technology Studies (D-RATS) October 2008 testing at Black Point Lava Flow (BPLF), Arizona. Refer to 39th International Conference on Environmental Systems (ICES) for test results of the EU. The suit port aft bulkhead mockup was integrated with the mockup of the LER cabin and chassis. It is located on the aft bulkhead of the LER cabin structure and includes hatches, a locking mechanism, seals, interior and exterior suit don/doff aids, and exterior platforms to accommodate different crewmember heights. A lightweight mockup of the Mark III suit was tested with the suit port aft bulkhead mockup. There are several limitations to the suit port and mockup suits, and results of the suit port evaluation are presented and interpreted within the context of the limitations.

  5. Small-Scale Spray Releases: Initial Aerosol Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, Lenna A.; Gauglitz, Phillip A.; Kimura, Marcia L.; Brown, Garrett N.; Kurath, Dean E.; Buchmiller, William C.; Smith, Dennese M.; Blanchard, Jeremy; Song, Chen; Daniel, Richard C.; Wells, Beric E.; Tran, Diana N.; Burns, Carolyn A.

    2012-11-01

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. Two key technical areas were identified where testing results were needed to improve the technical basis by reducing the uncertainty due to extrapolating existing literature results. The first technical need was to quantify the role of slurry particles in small breaches where the slurry particles may plug and result in substantially reduced, or even negligible, respirable fraction formed by high-pressure sprays. The second technical need was to determine the aerosol droplet size distribution and volume from prototypic breaches and fluids, specifically including sprays from larger breaches with slurries where data from the literature are scarce. To address these technical areas, small- and large-scale test stands were constructed and operated with simulants to determine aerosol release fractions and generation rates from a range of breach sizes and geometries. The properties of the simulants represented the range of properties expected in the WTP process streams and included water, sodium salt solutions, slurries containing boehmite or gibbsite, and a hazardous chemical simulant. The effect of anti-foam agents was assessed with most of the simulants. Orifices included round holes and

  6. Results for the Brine Evaporation Bag (BEB) Brine Processing Test

    Science.gov (United States)

    Delzeit, Lance; Flynn, Michael; Fisher, John; Shaw, Hali; Kawashima, Brian; Beeler, David; Howard, Kevin

    2015-01-01

    The recent Brine Processing Test compared the NASA Forward Osmosis Brine Dewatering (FOBD), Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB). This paper reports the results of the BEB. The BEB was operated at 70 deg C and a base pressure of 12 torr. The BEB was operated in a batch mode, and processed 0.4L of brine per batch. Two different brine feeds were tested, a chromic acid-urine brine and a chromic acid-urine-hygiene mix brine. The chromic acid-urine brine, known as the ISS Alternate Pretreatment Brine, had an average processing rate of 95 mL/hr with a specific power of 5kWhr/L. The complete results of these tests will be reported within this paper.

  7. Guidelines to Interpret Results of Mechanical Blade Test

    Energy Technology Data Exchange (ETDEWEB)

    Arias Vega, F.; Sanz Martin, J. C. [Ciemat, Madrid (Spain)

    2000-07-01

    This report shows the interpretation of full scale rotor blade test results and describes the engineering testing models and coefficients for any feasible rotor blade design, in order to accept and to certify any final manufactured blades as an allowable product, fit for use and working with a completely security during all the windturbine's lifetime. This work was carried out at the Wind Energy Division of the CIEMAT.DER and it is based on the author's technical experience in this field, after many years working on testing blades. Also, this paper contains results of the European wind turbine Standards II relevant to the European Project: JOULE III R.D. where the Wind Energy Division took part as participant too. (Author)

  8. GICHD mine dog testing project - soil sample results #4.

    Energy Technology Data Exchange (ETDEWEB)

    Barnett, James L.; Phelan, James M.; Archuleta, Luisa M.; Wood, Tyson B.; Donovan, Kelly L.; Bender, Susan Fae Ann

    2003-08-01

    A mine dog evaluation project initiated by the Geneva International Center for Humanitarian Demining is evaluating the capability and reliability of mine detection dogs. The performance of field-operational mine detection dogs will be measured in test minefields in Afghanistan and Bosnia containing actual, but unfused landmines. Repeated performance testing over two years through various seasonal weather conditions will provide data simulating near real world conditions. Soil samples will be obtained adjacent to the buried targets repeatedly over the course of the test. Chemical analysis results from these soil samples will be used to evaluate correlations between mine dog detection performance and seasonal weather conditions. This report documents the analytical chemical methods and results from the fourth batch of soils received. This batch contained samples from Kharga, Afghanistan collected in April 2003 and Sarajevo, Bosnia collected in May 2003.

  9. GICHD mine dog testing project : soil sample results #5.

    Energy Technology Data Exchange (ETDEWEB)

    Barnett, James L.; Phelan, James M.; Archuleta, Luisa M.; Donovan, Kelly L.; Bender, Susan Fae Ann

    2004-01-01

    A mine dog evaluation project initiated by the Geneva International Center for Humanitarian Demining is evaluating the capability and reliability of mine detection dogs. The performance of field-operational mine detection dogs will be measured in test minefields in Afghanistan containing actual, but unfused landmines. Repeated performance testing over two years through various seasonal weather conditions will provide data simulating near real world conditions. Soil samples will be obtained adjacent to the buried targets repeatedly over the course of the test. Chemical analysis results from these soil samples will be used to evaluate correlations between mine dog detection performance and seasonal weather conditions. This report documents the analytical chemical methods and results from the fifth batch of soils received. This batch contained samples from Kharga, Afghanistan collected in June 2003.

  10. Test results of a shower water recovery system

    Science.gov (United States)

    Verostko, Charles E.; Price, Donald F.; Garcia, Rafael; Pierson, Duane L.; Sauer, Richard L.

    1987-01-01

    A shower test was conducted recently at NASA-JSC in which waste water was reclaimed and reused. Test subjects showered in a prototype whole body shower following a protocol similar to that anticipated for Space Station. The waste water was purified using reverse osmosis followed by filtration through activated carbon and ion exchange resin beds. The reclaimed waste water was maintained free of microorganisms by using both heat and iodine. This paper discusses the test results, including the limited effectiveness of using iodine as a disinfectant and the evaluation of a Space Station candidate soap for showering. In addition, results are presented on chemical and microbial impurity content of water samples obtained from various locations in the water recovery process.

  11. Testing Result Statistics-Based Rapid Testing Method for Safety-Critical System

    Institute of Scientific and Technical Information of China (English)

    Zhi-Yao Deng; Nan Sang

    2008-01-01

    Safety-critical system (SCS) has highlydemand for dependability, which requires plenty ofresource to ensure that the system under test (SUT)satisfies the dependability requirement. In this paper, anew SCS rapid testing method is proposed to improveSCS adaptive dependability testing. The result of each testexecution is saved in calculation memory unit andevaluated as an algorithm model. Then the least quantityof scenario test case for next test execution will becalculated according to the promised SUT's confidencelevel. The feedback data are generated to weightcontroller as the guideline for the further testing. Finally,a compre- hensive experiment study demonstrates thatthis adaptive testing method can really work in practice.This rapid testing method, testing result statistics-basedadaptive control, makes the SCS dependability testingmuch more effective.

  12. ATLAS Transition Radiation Tracker test-beam results

    CERN Document Server

    Åkesson, T; Baker, K; Baron, S; Benjamin, D; Bertelsen, H; Bondarenko, V; Bychkov, V; Callahan, J; Capéans-Garrido, M; Cardiel-Sas, L; Catinaccio, A; Cetin, S A; Cwetanski, Peter; Dam, M; Danielsson, H; Dittus, F; Dolgoshein, B A; Dressnandt, N; Driouichi, C; Ebenstein, W L; Eerola, Paule Anna Mari; Farthouat, Philippe; Fedin, O; Froidevaux, D; Gagnon, P; Grichkevitch, Y; Grigalashvili, N S; Hajduk, Z; Hansen, P; Kayumov, F; Keener, P T; Kekelidze, G D; Khristatchev, A; Konovalov, S; Koudine, L; Kovalenko, S; Kowalski, T; Kramarenko, V A; Krüger, K; Laritchev, A; Lichard, P; Luehring, F C; Lundberg, B; Maleev, V; Markina, I; McFarlane, K W; Mialkovski, V; Mitsou, V A; Mindur, B; Morozov, S; Munar, A; Muraviev, S; Nadtochy, A; Newcomer, F M; Ögren, H O; Oh, S H; Oleshko, S; Olszowska, J; Passmore, S; Patritchev, S; Peshekhonov, V D; Petti, R; Price, M; Rembser, C; Rohne, O; Romaniouk, A; Rust, D R; Ryabov, Yu; Shchegelskii, V; Seliverstov, D M; Shin, T; Shmeleva, A; Smirnov, S; Sosnovtsev, V V; Soutchkov, V; Spiridenkov, E; Tikhomirov, V; Van Berg, R; Vassilakopoulos, V I; Vassilieva, L; Wang, C; Williams, H H; Zalite, A

    2004-01-01

    Several prototypes of the Transition Radiation Tracker for the ATLAS experiment at the LHC have been built and tested at the CERN SPS accelerator. Results from detailed studies of the straw-tube hit registration efficiency and drift-time measurements and of the pion and electron spectra without and with radiators are presented. (10 refs).

  13. Recent results on the RIA test in IGR reactor

    Energy Technology Data Exchange (ETDEWEB)

    Asmolov, V.; Yegorova, L. [Nuclear Safety Institute, Moscow (Russian Federation)

    1997-01-01

    At the 23d WRSM meeting the data base characterizing results of VVER high burnup fuel rods tests under reactivity-initiated accident (RIA) conditions was presented. Comparison of PWR and VVER failure thresholds was given also. Additional analysis of the obtained results was being carried out during 1996. The results of analysis show that the two different failure mechanisms were observed for PWR and VVER fuel rods. Some factors which can be as the possible reasons of these differences are presented. First of them is the state of preirradiated cladding. Published test data for PWR high burnup fuel rods demonstrated that the PWR high burnup fuel rods failed at the RIA test are characterized by very high level of oxidation and hydriding for the claddings. Corresponding researches were performed at Institute of Atomic Reactors (RLAR, Dimitrovgrad, Russia) for large set of VVER high burnup fuel rods. Results of these investigations show that preirradiated commercial Zr-1%Nb claddings practically keep their initial levels of oxidation and H{sub 2} concentration. Consequently the VVER preirradiated cladding must keep the high level of mechanical properties. The second reason leading to differences between failure mechanisms for two types of high burnup fuel rods can be the test conditions. Now such kind of analysis have been performed by two methods.

  14. Li-Ion Cell Lot Testing and Flight Screening Results

    Science.gov (United States)

    2011-02-01

    than \\c7<. Results arc shown in Table 4. Table 4 Moli-Energ) Li-Ion Cell Weights Alter Vaeuun Leak Tesi Initial Final Final Weight Weight...All tested cells were within 95 *5! o\\ their initial capacity. Note: Cells C009 and C023 were misplaced following being weighed after the vac- uum

  15. Test Beam Results Obtained with the Q4 Prototype

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar-Benitez, M.; Alberdi, J.; Cerrada, M.; Colino, N.; Daniel, M.; Fouz, M. c.; Marin, J.; Mocholi, J.; Oller, J. C.; Puerta, J.; Romero, L.; Salicio, J. M.

    2000-07-01

    A prototype of the CMS Barrel Muon Detector incorporating all the features of the final chambers was built at CIEMAT using the mass production assembly procedures and tools. The performance of this prototype was studied in a muon test beam at CERN and the results obtained are presented here. (Author)

  16. SSPS results of test and operation, 1981-1984

    Energy Technology Data Exchange (ETDEWEB)

    None

    1985-05-01

    The results of three years of testing and operation of the two dissimilar solar thermal power plants of the SSPS project are summarized. The project includes: (1) a Distributed Collector System, and (2) a Central Receiver System. Environmental conditions are presented and an economical assessment of the project is provided. (BCS)

  17. Potential for false positive HIV test results with the serial rapid HIV testing algorithm

    Directory of Open Access Journals (Sweden)

    Baveewo Steven

    2012-03-01

    Full Text Available Abstract Background Rapid HIV tests provide same-day results and are widely used in HIV testing programs in areas with limited personnel and laboratory infrastructure. The Uganda Ministry of Health currently recommends the serial rapid testing algorithm with Determine, STAT-PAK, and Uni-Gold for diagnosis of HIV infection. Using this algorithm, individuals who test positive on Determine, negative to STAT-PAK and positive to Uni-Gold are reported as HIV positive. We conducted further testing on this subgroup of samples using qualitative DNA PCR to assess the potential for false positive tests in this situation. Results Of the 3388 individuals who were tested, 984 were HIV positive on two consecutive tests, and 29 were considered positive by a tiebreaker (positive on Determine, negative on STAT-PAK, and positive on Uni-Gold. However, when the 29 samples were further tested using qualitative DNA PCR, 14 (48.2% were HIV negative. Conclusion Although this study was not primarily designed to assess the validity of rapid HIV tests and thus only a subset of the samples were retested, the findings show a potential for false positive HIV results in the subset of individuals who test positive when a tiebreaker test is used in serial testing. These findings highlight a need for confirmatory testing for this category of individuals.

  18. Large-Scale Spray Releases: Initial Aerosol Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Schonewill, Philip P.; Gauglitz, Phillip A.; Bontha, Jagannadha R.; Daniel, Richard C.; Kurath, Dean E.; Adkins, Harold E.; Billing, Justin M.; Burns, Carolyn A.; Davis, James M.; Enderlin, Carl W.; Fischer, Christopher M.; Jenks, Jeromy WJ; Lukins, Craig D.; MacFarlan, Paul J.; Shutthanandan, Janani I.; Smith, Dennese M.

    2012-12-01

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. Two key technical areas were identified where testing results were needed to improve the technical basis by reducing the uncertainty due to extrapolating existing literature results. The first technical need was to quantify the role of slurry particles in small breaches where the slurry particles may plug and result in substantially reduced, or even negligible, respirable fraction formed by high-pressure sprays. The second technical need was to determine the aerosol droplet size distribution and volume from prototypic breaches and fluids, specifically including sprays from larger breaches with slurries where data from the literature are scarce. To address these technical areas, small- and large-scale test stands were constructed and operated with simulants to determine aerosol release fractions and generation rates from a range of breach sizes and geometries. The properties of the simulants represented the range of properties expected in the WTP process streams and included water, sodium salt solutions, slurries containing boehmite or gibbsite, and a hazardous chemical simulant. The effect of anti-foam agents was assessed with most of the simulants. Orifices included round holes and

  19. Graphite electrode arc melter demonstration Phase 2 test results

    Energy Technology Data Exchange (ETDEWEB)

    Soelberg, N.R.; Chambers, A.G.; Anderson, G.L.; O`Connor, W.K.; Oden, L.L.; Turner, P.C.

    1996-06-01

    Several U.S. Department of Energy organizations and the U.S. Bureau of Mines have been collaboratively conducting mixed waste treatment process demonstration testing on the near full-scale graphite electrode submerged arc melter system at the Bureau`s Albany (Oregon) Research Center. An initial test series successfully demonstrated arc melter capability for treating surrogate incinerator ash of buried mixed wastes with soil. The conceptual treatment process for that test series assumed that buried waste would be retrieved and incinerated, and that the incinerator ash would be vitrified in an arc melter. This report presents results from a recently completed second series of tests, undertaken to determine the ability of the arc melter system to stably process a wide range of {open_quotes}as-received{close_quotes} heterogeneous solid mixed wastes containing high levels of organics, representative of the wastes buried and stored at the Idaho National Engineering Laboratory (INEL). The Phase 2 demonstration test results indicate that an arc melter system is capable of directly processing these wastes and could enable elimination of an up-front incineration step in the conceptual treatment process.

  20. Long Term Corrosion/Degradation Test Six Year Results

    Energy Technology Data Exchange (ETDEWEB)

    M. K. Adler Flitton; C. W. Bishop; M. E. Delwiche; T. S. Yoder

    2004-09-01

    The Subsurface Disposal Area (SDA) of the Radioactive Waste Management Complex (RWMC) located at the Idaho National Engineering and Environmental Laboratory (INEEL) contains neutron-activated metals from non-fuel, nuclear reactor core components. The Long-Term Corrosion/Degradation (LTCD) Test is designed to obtain site-specific corrosion rates to support efforts to more accurately estimate the transfer of activated elements to the environment. The test is using two proven, industry-standard methods—direct corrosion testing using metal coupons, and monitored corrosion testing using electrical/resistance probes—to determine corrosion rates for various metal alloys generally representing the metals of interest buried at the SDA, including Type 304L stainless steel, Type 316L stainless steel, Inconel 718, Beryllium S200F, Aluminum 6061, Zircaloy-4, low-carbon steel, and Ferralium 255. In the direct testing, metal coupons are retrieved for corrosion evaluation after having been buried in SDA backfill soil and exposed to natural SDA environmental conditions for times ranging from one year to as many as 32 years, depending on research needs and funding availability. In the monitored testing, electrical/resistance probes buried in SDA backfill soil will provide corrosion data for the duration of the test or until the probes fail. This report provides an update describing the current status of the test and documents results to date. Data from the one-year and three-year results are also included, for comparison and evaluation of trends. In the six-year results, most metals being tested showed extremely low measurable rates of general corrosion. For Type 304L stainless steel, Type 316L stainless steel, Inconel 718, and Ferralium 255, corrosion rates fell in the range of “no reportable” to 0.0002 mils per year (MPY). Corrosion rates for Zircaloy-4 ranged from no measurable corrosion to 0.0001 MPY. These rates are two orders of magnitude lower than those specified in

  1. PISA TESTS IN LATIN AMERICA: RESULTS IN CONTEXT

    Directory of Open Access Journals (Sweden)

    Guillermina Tiramonti

    2014-05-01

    Full Text Available The educational reforms implemented in Latin America in the ‘90s introduced changes in the modes of regulation of educational systems based on the adoption of mechanisms for assessing student achievement. Since 2000, eight Latin-American countries (Argentina, Chile, Uruguay, Colombia, Brazil, Costa Rica, Mexico and Peru are involved in the PISA tests. The article presents a brief review of the social and educational situation of the Region, relevant for the interpretation and comparative analysis of the results of these tests that is presented below.

  2. Patch Test Results of 775 Patients with Allergic Contact Dermatitis

    Directory of Open Access Journals (Sweden)

    Simin Ada

    2010-12-01

    Full Text Available Background and Design: The allergens responsible for allergic contact dermatitis vary among countries and even between different geographical regions within the same country over time. It is of great importance to perform the patch test at certain intervals, to evaluate the results in different centers and to compare them afterwards. Our aim was to evaluate the patch test results in our patients with allergic contact dermatitis.Material and Method: The records of the patients with allergic contact dermatitis, who had been patch tested between May 1997 and March 2009, were analyzed retrospectively. The demographic features such as age and sex, localization of the contact dermatitis, and the patch test results were recorded. Results: Of the 775 patients, 581 (75.2% were females and 194 (25% males. Of all patients, 735 were patch tested with the European Standard Series, 318 - with both the European Standard Series and cosmetic series, and 40-with cosmetic series alone. Of the patients tested with the European Standard Series, 255 (34.7% had at least one positive reaction. The most frequent allergen in the European Standard Series was nickel sulfate (17.3%, followed by cobalt chloride (7.2%, potassium dichromate (3%, fragrance mix (2.9%, and p-phenylenediamine base (2.6%. Of the 358 patients tested with cosmetic series, 82 (22.9% had at least one positive reaction. The 5 most frequently observed cosmetic series allergens were octyl gallate (3.9%, thimerosal (2.2%, sorbitan sesquioleate (2%, Euxyl K 400 (2% and methyldibromo glutaronitrile (1.4%. Conclusion: Our study shows the contact allergen profile of our center over 12 years. The most common allergens and their frequency differ between centers in various cities in Turkey. Those geographical differences should be re-evaluated by further studies performed in the certain time period. The high frequency of reactions to octyl gallate is an important finding in patients suspected of cosmetic allergy

  3. ITER CS Model Coil and CS Insert Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Martovetsky, N; Michael, P; Minervina, J; Radovinsky, A; Takayasu, M; Thome, R; Ando, T; Isono, T; Kato, T; Nakajima, H; Nishijima, G; Nunoya, Y; Sugimoto, M; Takahashi, Y; Tsuji, H; Bessette, D; Okuno, K; Ricci, M

    2000-09-07

    The Inner and Outer modules of the Central Solenoid Model Coil (CSMC) were built by US and Japanese home teams in collaboration with European and Russian teams to demonstrate the feasibility of a superconducting Central Solenoid for ITER and other large tokamak reactors. The CSMC mass is about 120 t, OD is about 3.6 m and the stored energy is 640 MJ at 46 kA and peak field of 13 T. Testing of the CSMC and the CS Insert took place at Japan Atomic Energy Research Institute (JAERI) from mid March until mid August 2000. This paper presents the main results of the tests performed.

  4. Interim Guidance for Interpretation of Zika Virus Antibody Test Results.

    Science.gov (United States)

    Rabe, Ingrid B; Staples, J Erin; Villanueva, Julie; Hummel, Kimberly B; Johnson, Jeffrey A; Rose, Laura; Hills, Susan; Wasley, Annemarie; Fischer, Marc; Powers, Ann M

    2016-06-03

    Zika virus is a single-stranded RNA virus in the genus Flavivirus and is closely related to dengue, West Nile, Japanese encephalitis, and yellow fever viruses (1,2). Among flaviviruses, Zika and dengue virus share similar symptoms of infection, transmission cycles, and geographic distribution. Diagnostic testing for Zika virus infection can be accomplished using both molecular and serologic methods. For persons with suspected Zika virus disease, a positive real-time reverse transcription-polymerase chain reaction (rRT-PCR) result confirms Zika virus infection, but a negative rRT-PCR result does not exclude infection (3-7). In these cases, immunoglobulin (Ig) M and neutralizing antibody testing can identify additional recent Zika virus infections (6,7). However, Zika virus antibody test results can be difficult to interpret because of cross-reactivity with other flaviviruses, which can preclude identification of the specific infecting virus, especially when the person previously was infected with or vaccinated against a related flavivirus (8). This is important because the results of Zika and dengue virus testing will guide clinical management. Pregnant women with laboratory evidence of Zika virus infection should be evaluated and managed for possible adverse pregnancy outcomes and be reported to the U.S. Zika Pregnancy Registry or the Puerto Rico Zika Active Pregnancy Surveillance System for clinical follow-up (9,10). All patients with clinically suspected dengue should have proper management to reduce the risk for hemorrhage and shock (11). If serologic testing indicates recent flavivirus infection that could be caused by either Zika or dengue virus, patients should be clinically managed for both infections because they might have been infected with either virus.

  5. Dipole model test with one superconducting coil; results analysed

    CERN Document Server

    Durante, M; Ferracin, P; Fessia, P; Gauthier, R; Giloux, C; Guinchard, M; Kircher, F; Manil, P; Milanese, A; Millot, J-F; Muñoz Garcia, J-E; Oberli, L; Perez, J-C; Pietrowicz, S; Rifflet, J-M; de Rijk, G; Rondeaux, F; Todesco, E; Viret, P; Ziemianski, D

    2013-01-01

    This report is the deliverable report 7.3.1 “Dipole model test with one superconducting coil; results analysed “. The report has four parts: “Design report for the dipole magnet”, “Dipole magnet structure tested in LN2”, “Nb3Sn strand procured for one dipole magnet” and “One test double pancake copper coil made”. The 4 report parts show that, although the magnet construction will be only completed by end 2014, all elements are present for a successful completion. Due to the importance of the project for the future of the participants and given the significant investments done by the participants, there is a full commitment to finish the project.

  6. Dipole model test with one superconducting coil: results analysed

    CERN Document Server

    Bajas, H; Benda, V; Berriaud, C; Bajko, M; Bottura, L; Caspi, S; Charrondiere, M; Clément, S; Datskov, V; Devaux, M; Durante, M; Fazilleau, P; Ferracin, P; Fessia, P; Gauthier, R; Giloux, C; Guinchard, M; Kircher, F; Manil, P; Milanese, A; Millot, J-F; Muñoz Garcia, J-E; Oberli, L; Perez, J-C; Pietrowicz, S; Rifflet, J-M; de Rijk, G; Rondeaux, F; Todesco, E; Viret, P; Ziemianski, D

    2013-01-01

    This report is the deliverable report 7.3.1 “Dipole model test with one superconducting coil; results analysed “. The report has four parts: “Design report for the dipole magnet”, “Dipole magnet structure tested in LN2”, “Nb3Sn strand procured for one dipole magnet” and “One test double pancake copper coil made”. The 4 report parts show that, although the magnet construction will be only completed by end 2014, all elements are present for a successful completion. Due to the importance of the project for the future of the participants and given the significant investments done by the participants, there is a full commitment to finish the project.

  7. DUS II SOIL GAS SAMPLING AND AIR INJECTION TEST RESULTS

    Energy Technology Data Exchange (ETDEWEB)

    Noonkester, J.; Jackson, D.; Jones, W.; Hyde, W.; Kohn, J.; Walker, R.

    2012-09-20

    Soil vapor extraction (SVE) and air injection well testing was performed at the Dynamic Underground Stripping (DUS) site located near the M-Area Settling Basin (referred to as DUS II in this report). The objective of this testing was to determine the effectiveness of continued operation of these systems. Steam injection ended on September 19, 2009 and since this time the extraction operations have utilized residual heat that is present in the subsurface. The well testing campaign began on June 5, 2012 and was completed on June 25, 2012. Thirty-two (32) SVE wells were purged for 24 hours or longer using the active soil vapor extraction (ASVE) system at the DUS II site. During each test five or more soil gas samples were collected from each well and analyzed for target volatile organic compounds (VOCs). The DUS II site is divided into four parcels (see Figure 1) and soil gas sample results show the majority of residual VOC contamination remains in Parcel 1 with lesser amounts in the other three parcels. Several VOCs, including tetrachloroethylene (PCE) and trichloroethylene (TCE), were detected. PCE was the major VOC with lesser amounts of TCE. Most soil gas concentrations of PCE ranged from 0 to 60 ppmv with one well (VEW-22A) as high as 200 ppmv. Air sparging (AS) generally involves the injection of air into the aquifer through either vertical or horizontal wells. AS is coupled with SVE systems when contaminant recovery is necessary. While traditional air sparging (AS) is not a primary component of the DUS process, following the cessation of steam injection, eight (8) of the sixty-three (63) steam injection wells were used to inject air. These wells were previously used for hydrous pyrolysis oxidation (HPO) as part of the DUS process. Air sparging is different from the HPO operations in that the air was injected at a higher rate (20 to 50 scfm) versus HPO (1 to 2 scfm). . At the DUS II site the air injection wells were tested to determine if air sparging affected

  8. Small-Scale Spray Releases: Orifice Plugging Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, Lenna A.; Gauglitz, Phillip A.; Blanchard, Jeremy; Kimura, Marcia L.; Kurath, Dean E.

    2012-09-01

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities, is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations published in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials present in the WTP and across processing facilities in the DOE complex. Two key technical areas were identified where testing results were needed to improve the technical basis by reducing the uncertainty introduced by extrapolating existing literature results. The first technical need was to quantify the role of slurry particles in small breaches in which the slurry particles may plug and result in substantially reduced, or even negligible, respirable fraction formed by high pressure sprays. The second technical need was to determine the aerosol droplet size distribution and volume from prototypic breaches and fluids, specifically including sprays from larger breaches with slurries where data from the literature are largely absent. To address these technical areas, small- and large-scale test stands were constructed and operated with simulants to determine the aerosol release fractions and aerosol generation rates from a range of breach sizes and geometries. The properties of the simulants represented the range of properties expected in the WTP process streams and included water, sodium salt solutions, slurries containing boehmite or gibbsite, and a hazardous chemical simulant. The effect of anti-foam agents (AFA) was assessed with most of the simulants. Orifices

  9. Cold test results for the test cavities w/out the deposited lead photo cathode

    CERN Document Server

    Sekutowicz, J

    2013-01-01

    In this report we present tests of a 1.5-cell superconducting photo-injector cavity, which was built in the frame of Task 4. The cavity was tested twice: without the cathode (baseline test) and with the lead photo-cathode. The result of tests was very encouraging and the decision was made to continue the experiment, beyond scope of the task, at HZB in Berlin to learn more about quality of the cathode.

  10. Large-Scale Spray Releases: Additional Aerosol Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Daniel, Richard C.; Gauglitz, Phillip A.; Burns, Carolyn A.; Fountain, Matthew S.; Shimskey, Rick W.; Billing, Justin M.; Bontha, Jagannadha R.; Kurath, Dean E.; Jenks, Jeromy WJ; MacFarlan, Paul J.; Mahoney, Lenna A.

    2013-08-01

    One of the events postulated in the hazard analysis for the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak event involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids that behave as a Newtonian fluid. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and in processing facilities across the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are mostly absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale testing. The small-scale testing and resultant data are described in Mahoney et al. (2012b), and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used

  11. Production Facility Prototype Blower 1000 Hour Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Woloshun, Keith Albert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Frank Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dalmas, Dale Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-10-18

    The roots blower in use at ANL for in-beam experiments and also at LANL for flow tests was sized for 12 mm diameter disks and significantly less beam heating. Currently, the disks are 29 mm in diameter, with a 12 mm FWHM Gaussian beam spot at 42 MeV and 2.86 μA on each side of the target, 5.72 μA total. The target design itself is reported elsewhere. With the increased beam heating, the helium flow requirement increased so that a larger blower was needed for a mass flow rate of 400 g/s at 2.76 MPa (400 psig). An Aerzen GM 12.4 blower was selected, and is now installed at the LANL facility for target and component flow testing. Two extended tests of >1000 hr operation have been completed. Those results and discussion thereof are reported herein. Also included in Appendix A is the detailed description of the blower and its installation, while Appendix B documents the pressure vessel design analysis. The blower has been operated for 1000 hours as a preliminary investigation of long-term performance, operation and possible maintenance issues. The blower performed well, with no significant change in blower head or mass flow rate developed under the operating conditions. Upon inspection, some oil had leaked out of the shaft seal of the blower. The shaft seal and bearing race have been replaced. Test results and conclusions are in Appendix B.

  12. Fan Noise Source Diagnostic Test: Tone Modal Structure Results

    Science.gov (United States)

    Heidelberg, Laurence J.

    2002-01-01

    This investigation is part of a test series that was extremely comprehensive and included aerodynamic and acoustic testing of a fan stage using two different fan rotors and three different stator designs. The test series is known as the Source Diagnostic Test (SDT) and was conducted by NASA Glenn as part of the Advanced Subsonic Technology (AST) Noise Reduction Program. Tone mode measurements of one of the rotors with three different stators were made. The stator designs involve changes in vane count and sweep at constant solidity. The results of both inlet and exhaust tone mode measurements are presented in terms of mode power for both circumferential and radial mode orders. The results show benefits of vane sweep to be large, up to 13 dB in total tone power. At many conditions, the increase in power due to cutting on the rotor/stator interaction is more than offset by vane sweep. The rotor locked mode is shown as an important contributor to tone power when the blade tip speed is near and above Mach one. This is most evident in the inlet when the direct rotor field starts to cut on.

  13. Production Facility Prototype Blower 1000 Hour Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Woloshun, Keith Albert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Frank Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dalmas, Dale Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-10-18

    The roots blower in use at ANL for in-beam experiments and also at LANL for flow tests was sized for 12 mm diameter disks and significantly less beam heating. Currently, the disks are 29 mm in diameter, with a 12 mm FWHM Gaussian beam spot at 42 MeV and 2.86 μA on each side of the target, 5.72 μA total. The target design itself is reported elsewhere. With the increased beam heating, the helium flow requirement increased so that a larger blower was need for a mass flow rate of 400 g/s at 2.76 MPa (400 psig). An Aerzen GM 12.4 blower was selected, and is now installed at the LANL facility for target and component flow testing. Two extended test of >1000 hr operation have been completed. Those results and discussion thereof are reported herein. Also included in Appendix A is the detailed description of the blower and its installation, while Appendix B documents the pressure vessel design analysis. The blower has been operated for 1000 hours as a preliminary investigation of long term performance, operation and possible maintenance issues. The blower performed well, with no significant change in blower head or mass flow rate developed under the operating conditions. Upon inspection, some oil had leaked out of the shaft seal of the blower. The shaft seal and bearing race have been replaced. Test results and conclusions are in Appendix B.

  14. Results of testing various natural gas desulfurization adsorbents

    Science.gov (United States)

    Israelson, Gordon

    2004-06-01

    This article presents the results of testing many commercially available and some experimental sulfur adsorbents. The desired result of our testing was to find an effective method to reduce the quantity of sulfur in natural gas to less than 100 ppb volume (0.1 ppm volume). An amount of 100 ppb sulfur is the maximum limit permitted for Siemens Westinghouse solid oxide fuel cells (SOFCs). The tested adsorbents include some that rely only on physical adsorption such as activated carbon, some that rely on chemisorption such as heated zinc oxide, and some that may use both processes. The testing was performed on an engineering scale with beds larger than those used for typical laboratory tests. All tests were done at about 3.45 barg (50 psig). The natural gas used for testing was from the local pipeline in Pittsburgh and averaged 6 ppm volume total sulfur. The primary sulfur species were dimethyl sulfide (DMS), isopropyl mercaptan, tertiary butyl mercaptan, and tetrahydrothiophene. Some tests required several months to achieve a sulfur breakthrough of the bed. It was found that DMS always came through a desulfurizer bed first, independent of adsorption process. Since the breakthrough of DMS always exceeds the 100 ppb SOFC sulfur limit before other sulfurs were detected, an index was created to rate the adsorbents in units of ppm DMS × absorbent bed volume. This index is useful for calculating the expected adsorbent bed lifetime before sulfur breakthrough when the inlet natural gas DMS content is known. The adsorbents that are included in these reports were obtained from suppliers in the United States, the Netherlands, Japan, and England. Three activated carbons from different suppliers were found to have identical performance in removing DMS. One of these activated carbons was operated at four different space velocities and again showed the same performance. When using activated carbon as the basis of comparison for other adsorbents, three high-performance adsorbents

  15. The XRS Low Temperature Cryogenic System: Ground Performance Test Results

    Science.gov (United States)

    Breon, Susan; Sirron, Peter; Boyle, Robert; Canavan, Ed; DiPirro, Michael; Serlemitsos, Aristides; Tuttle, James; Whitehouse, Paul

    1998-01-01

    The X-Ray Spectrometer (XRS) instrument is part of the Astro-E mission scheduled to launch early in 2000. Its cryogenic system is required to cool a 32-element square array of x-ray microcalorimeters to 60-65 mK over a mission lifetime of at least 2 years. This is accomplished using an adiabatic demagnetization refrigerator (ADR) contained within a two-stage superfluid helium/solid neon cooler. Goddard Space Flight Center is providing the ADR and helium dewar. The flight system was assembled in Sept. 1997 and subjected to extensive thermal performance tests. This paper presents test results at both the system and component levels. In addition, results of the low temperature topoff performed in Japan with the engineering unit neon and helium dewars are discussed.

  16. The CLEO-III RICH Detector and Beam Test Results

    CERN Document Server

    Wang, J C; Ayad, R; Azfar, F; Dambasuren, E; Efimov, A; Kopp, S E; Majumder, G; Mountain, R; Schuh, S; Skwarnicki, T; Stone, S; Viehhauser, G; Anderson, S; Smith, A; Kubota, Y; Lipeles, E; Coan, T E; Staeck, J; Fadeev, V; Volobuev, I P

    1999-01-01

    We are constructing a Ring Imaging Cherenkov detector (RICH) for the CLEO III upgrade for precision charged hadron identification. The RICH uses plane and sawtooth LiF crystals as radiators, MWPCs as photon detectors with TEA as the photo-sensitive material, and low-noise Viking readout electronics. Results of a beam test of the first two out of total 30 sectors are presented.

  17. Seismic II over I Drop Test Program results and interpretation

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, B.

    1993-03-01

    The consequences of non-seismically qualified (Category 2) objects falling and striking essential seismically qualified (Category 1) objects has always been a significant, yet analytically difficult problem, particularly in evaluating the potential damage to equipment that may result from earthquakes. Analytical solutions for impact problems are conservative and available for mostly simple configurations. In a nuclear facility, the [open quotes]sources[close quotes] and [open quotes]targets[close quotes] requiring evaluation are frequently irregular in shape and configuration, making calculations and computer modeling difficult. Few industry or regulatory rules are available on this topic even though it is a source of considerable construction upgrade costs. A drop test program was recently conducted to develop a more accurate understanding of the consequences of seismic interactions. The resulting data can be used as a means to improve the judgment of seismic qualification engineers performing interaction evaluations and to develop realistic design criteria for seismic interactions. Impact tests on various combinations of sources and targets commonly found in one Savannah River Site (SRS) nuclear facility were performed by dropping the sources from various heights onto the targets. This report summarizes results of the Drop Test Program. Force and acceleration time history data are presented as well as general observations on the overall ruggedness of various targets when subjected to impacts from different types of sources.

  18. Seismic II over I Drop Test Program results and interpretation

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, B.

    1993-03-01

    The consequences of non-seismically qualified (Category 2) objects falling and striking essential seismically qualified (Category 1) objects has always been a significant, yet analytically difficult problem, particularly in evaluating the potential damage to equipment that may result from earthquakes. Analytical solutions for impact problems are conservative and available for mostly simple configurations. In a nuclear facility, the {open_quotes}sources{close_quotes} and {open_quotes}targets{close_quotes} requiring evaluation are frequently irregular in shape and configuration, making calculations and computer modeling difficult. Few industry or regulatory rules are available on this topic even though it is a source of considerable construction upgrade costs. A drop test program was recently conducted to develop a more accurate understanding of the consequences of seismic interactions. The resulting data can be used as a means to improve the judgment of seismic qualification engineers performing interaction evaluations and to develop realistic design criteria for seismic interactions. Impact tests on various combinations of sources and targets commonly found in one Savannah River Site (SRS) nuclear facility were performed by dropping the sources from various heights onto the targets. This report summarizes results of the Drop Test Program. Force and acceleration time history data are presented as well as general observations on the overall ruggedness of various targets when subjected to impacts from different types of sources.

  19. Small-Scale Spray Releases: Additional Aerosol Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Schonewill, Philip P.; Gauglitz, Phillip A.; Kimura, Marcia L.; Brown, G. N.; Mahoney, Lenna A.; Tran, Diana N.; Burns, Carolyn A.; Kurath, Dean E.

    2013-08-01

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are largely absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale. The small-scale testing and resultant data are described in Mahoney et al. (2012b) and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used to mimic the

  20. Fan Noise Source Diagnostic Test: Rotor Alone Aerodynamic Performance Results

    Science.gov (United States)

    Hughes, Christopher E.; Jeracki, Robert J.; Woodward, Richard P.; Miller, Christopher J.

    2005-01-01

    The aerodynamic performance of an isolated fan or rotor alone model was measured in the NASA Glenn Research Center 9- by 15- Foot Low Speed Wind Tunnel as part of the Fan Broadband Source Diagnostic Test conducted at NASA Glenn. The Source Diagnostic Test was conducted to identify the noise sources within a wind tunnel scale model of a turbofan engine and quantify their contribution to the overall system noise level. The fan was part of a 1/5th scale model representation of the bypass stage of a current technology turbofan engine. For the rotor alone testing, the fan and nacelle, including the inlet, external cowl, and fixed area fan exit nozzle, were modeled in the test hardware; the internal outlet guide vanes located behind the fan were removed. Without the outlet guide vanes, the velocity at the nozzle exit changes significantly, thereby affecting the fan performance. As part of the investigation, variations in the fan nozzle area were tested in order to match as closely as possible the rotor alone performance with the fan performance obtained with the outlet guide vanes installed. The fan operating performance was determined using fixed pressure/temperature combination rakes and the corrected weight flow. The performance results indicate that a suitable nozzle exit was achieved to be able to closely match the rotor alone and fan/outlet guide vane configuration performance on the sea level operating line. A small shift in the slope of the sea level operating line was measured, which resulted in a slightly higher rotor alone fan pressure ratio at take-off conditions, matched fan performance at cutback conditions, and a slightly lower rotor alone fan pressure ratio at approach conditions. However, the small differences in fan performance at all fan conditions were considered too small to affect the fan acoustic performance.

  1. Performance test results for the Eaton dc development power train in an electric test bed vehicle

    Science.gov (United States)

    Crumley, R. L.; Donaldson, M. R.

    1987-09-01

    This report presents the results of the tests performed on a direct current (dc) power train in a test bed vehicle developed by the Eaton Corporation for the U.S. Department of Energy (DOE). The tests were performed by EG and G Idaho, Inc. at the Idaho National Engineering Laboratory (INEL). The purpose of the INEL testing was to provide test results from which an evaluation of the performance capabilities of the Eaton dc power train could be made and compared with other vehicle propulsion systems. The planned tests were primarily oriented toward road testing, chassis dynamometer testing, and associated dynamometer coastdown tests for road loss determination. Range tests of the Eaton dc test bed vehicle using an ALCO 2200 lead acid battery pack, produced ranges of 97 km at 56 km/h (60 miles at 35 mph), 79 km at 72 km/h (49 miles at 45 mph), and 47 km at 88 km/h (29 miles at 55 mph). The corresponding net dc energy consumptions are 135 Wh/km (217 Wh/mile), 145 Wh/km (233 Wh/mile), and 178 Wh/km (287 Wh/mile). The energy consumption for the D-cycle test was 241 Wh/km (387 Wh/mile).

  2. What Do the Results of Genetic Tests Mean?

    Science.gov (United States)

    ... can ask their healthcare professional. Topics in the Genetic Testing chapter What is genetic testing? What are the types of genetic tests? How is genetic testing done? What is informed consent? What is direct- ...

  3. Test results of the optical PAT test bed for satellite laser communications

    Science.gov (United States)

    Sun, Jianfeng; Liu, Liren; Zhou, Yu; Liu, De'an

    2008-08-01

    Satellite laser communication systems offer many advantages such as high data rate, small sized equipment, low consumption electric power and others. Recent successful demonstrations of laser communications have demonstrated the feasibility of some of the key aspects of this technology. Sub-microradian pointing, acquisition, and tracking (PAT) functions are key issue to establish the laser communication system in space. The terminals must perform a series of onground test to evaluate characteristics of The PAT performances before flight test. So an optical dynamical PAT test bed is developed to perform ground test of a laser terminal. In this paper, we detail the separate test and the system test results of the optical dynamical PAT test bed. The test was carried out by auto-collimation method, the precision deflect accuracy, scan accuracy and deflect scan accuracy are obtained.

  4. SCD1 thermal design and test result analysis

    Science.gov (United States)

    Cardoso, Humberto Pontes; Muraoka, Issamu; Mantelli, Marcia Barbosa Henriques; Leite, Rosangela M. G.

    1990-01-01

    The SCD 01 (Satelite de Coleta de Dados 01) is a spin stabilized low Earth orbit satellite dedicated to the collection and distribution of environmental data. It was completely developed at the Brazilian Institute for Space Research (INPE) and is scheduled to be launched in 1992. The SCD 01 passive thermal control design configuration is presented and the thermal analysis results are compared with the temperatures obtained from a Thermal Balance Test. The correlation between the analytical and experimental results is considered very good. Numerical flight simulations show that the thermal control design can keep all the subsystem temperatures within their specified temperature range.

  5. Challenges in interpretation of thyroid hormone test results

    Directory of Open Access Journals (Sweden)

    Lalić Tijana

    2016-01-01

    Full Text Available Introduction. In interpreting thyroid hormones results it is preferable to think of interference and changes in concentration of their carrier proteins. Outline of Cases. We present two patients with discrepancy between the results of thyroid function tests and clinical status. The first case presents a 62-year-old patient with a nodular goiter and Hashimoto thyroiditis. Thyroid function test showed low thyroid-stimulating hormone (TSH and normal to low fT4. By determining thyroid status (ТSH, T4, fT4, T3, fT3 in two laboratories, basal and after dilution, as well as thyroxine-binding globulin (TBG, it was concluded that the thyroid hormone levels were normal. The results were influenced by heterophile antibodies leading to a false lower TSH level and suspected secondary hypothyroidism. The second case, a 40-year-old patient, was examined and followed because of the variable size thyroid nodule and initially borderline elevated TSH, after which thyroid status showed low level of total thyroid hormones and normal TSH. Based on additional analysis it was concluded that low T4 and T3 were a result of low TBG. It is a hereditary genetic disorder with no clinical significance. Conclusion. Erroneous diagnosis of thyroid disorders and potentially harmful treatment could be avoided by proving the interference or TBG deficiency whenever there is a discrepancy between the thyroid function results and the clinical picture.

  6. Absorption characteristics of anechoic coating on cavity structure and its optimization design%混合型空腔结构覆盖层吸声性能研究及其优化设计

    Institute of Scientific and Technical Information of China (English)

    商超; 张嘉钟; 曹伟; 于开平

    2011-01-01

    基于有限元法研究了以空气为背衬的混合型空腔结构覆盖层的吸声特性.建立了具有混合型空腔结构的覆盖层有限元模型,对其进行吸声特性数值仿真分析.结果表明,该空腔结构的吸声特性明显优于相同穿孔率的单腔结构.通过优化设计,进一步提升了混合型空腔结构覆盖层在全频段的吸声性能,并得到了若干覆盖层结构参数影响其吸声性能的规律.%The absorption characteristics of the mixed-cavity structure anechoic coating with air backing were studied by using finite element method. The calculation results indicate that the absorption characteristics of this kind of cavity structure are superior to those of single-cavity structure under the same perforated percentage. Then, the absorption properties of anechoic coating on mixed-cavity structure at full-frequency range were further improved by optimization design. The influence of coating structure parameters on absorption characteristics was studied.

  7. Suit Port Aft Bulkhead Mockup Test Results and Lessons Learned

    Science.gov (United States)

    Romig, Barbara A.; Allton, Charles

    2009-01-01

    The Small Pressurized Rover (SPR) is currently being carried as an integral part of the current Lunar Surface Architectures under consideration in the Constellation program. One element of the SPR is the suit port, the means by which the crew performs Extravehicular Activities (EVAs). Two suit port deliverables were produced in fiscal year 2008: an aft bulkhead mockup for functional integrated testing with the 1-G SPR mockup and a functional and pressurizable engineering unit. This paper focuses on the test results and lessons learned on the aft bulkhead mockup. The suit port aft bulkhead mockup was integrated with the mockup of the SPR cabin and chassis. It is located on the aft bulkhead of the SPR cabin structure and includes hatches, a locking mechanism, seals, interior and exterior suit don/doff aids, and exterior platforms to accommodate different crewmember heights. A lightweight mockup of the Mark III suit was tested with the suit port aft bulkhead mockup. There are several limitations to the suit port and mockup suits, and results of the suit port evaluation are presented and interpreted within the context of the limitations.

  8. Polynomial Tests of Normal Forms and Some Related Results

    Institute of Scientific and Technical Information of China (English)

    王克

    1992-01-01

    The following problem is called the everywhere-cover problem:“Given a set of dependencies over a database scheme,is he set of dependencies explicitly given for each relation scheme equivalent to the dependencies implied for that relation sheme?”It is shown that when the everywhere-cover problem has a yes answer,examining only the dependencies explicitly given will suffice to test 3NF, BCNF and 4NF of a database scheme.But this does not hold for 2NF.Consequently,in such cases,tests of BCNF and 4NF all take polynomial time.Then a proof is given that test of 3NF of a database scheme is Co-NP-complete,and from this result it is shown that everywhere-cover is also Co-NP-complete when only functional dependencies are allowed.These results lead to doubt the truth of the well believed conjecture that no polynomial time algorithm for designing a lossless BCNF database scheme is likely to exist.

  9. Beam Test Results of High Q CBPM prototype for SXFEL

    CERN Document Server

    Chen, Jian; Yu, Luyang; Lai, Longwei; Yuan, Renxian

    2016-01-01

    Aiming at high precision beam position measurement of micron or sub-micron for Shanghai Soft X-ray free electron laser (SXFEL) facility which is being built in site of the Shanghai Synchrotron Radiation Facility (SSRF), Shanghai Institute of Applied Physics has developed a high Q cavity beam position monitor (CBPM) that the resonant frequency is 4.7 GHz and relevant BPM electronics include dedicated RF front-end and home-made digital BPM (DBPM) also has been done. The cavity design, cold test, system architecture and the beam test with three adjacent pickups has been performed in Shanghai Deep ultraviolet free electron laser(SDUV-FEL) facility are included. The beam experiment results show that the physical design of our CBPM is consistent with the expectations basically and the beam position resolution can fulfill the resolution requirements for the SXFEL project if we optimize the beam conditions.

  10. High School Staff Characteristics and Mathematics Test Results

    Directory of Open Access Journals (Sweden)

    Mark Fetler

    1999-03-01

    Full Text Available This study investigates the relationship between measures of mathematics teacher skill and student achievement in California high schools. Test scores are analyzed in relation to teacher experience and education and student demographics. The results are consistent with the hypotheses that there is a shortage of qualified mathematics teachers in California and that this shortage is associated with low student scores in mathematics. After controlling for poverty, teacher experience and preparation significantly predict test scores. Short-term strategies to increase the supply of qualified mathematics teachers could include staff development, and recruitment incentives. A long-term strategy addressing root causes of the shortage requires more emphasis on mathematics in high school and undergraduate programs.

  11. Test Results of the ALICE SDD Electronic Readout Prototypes

    CERN Document Server

    Mazza, G; Anelli, G; Bonazzola, G C; Cavagnino, D; Cerello, P G; De Remigis, P; Falchieri, D; Gabrielli, A; Gandolfi, E; Giubellino, P; Masetti, M; Montaño-Zetina, L M; Nouais, D; Rivetti, A; Tosello, F; Werbrouck, A E; Wheadon, R

    2000-01-01

    The first prototypes of the front-end electronics of the ALICE silicon driftdetectors have been designed and tested. The integrated circuits have been designed using state of the art technologies and, for the analog parts, with radiation-tolerantdesign techniques. In this paper, the test results of the building blocks of the PASCAL chip and the first prototype of the AMBRA chip are presented. The prototypes fully respect the ALICE requirements; owingto the use of deep-submicron technologies together with radiation-tolerant layout techniques, the prototypes have shown a toleranceto a radiation dose much higher than the one foreseen for the ALICE environment.(Abstract only available, full text to follow).

  12. Hanford coring bit temperature monitor development testing results report

    Energy Technology Data Exchange (ETDEWEB)

    Rey, D.

    1995-05-01

    Instrumentation which directly monitors the temperature of a coring bit used to retrieve core samples of high level nuclear waste stored in tanks at Hanford was developed at Sandia National Laboratories. Monitoring the temperature of the coring bit is desired to enhance the safety of the coring operations. A unique application of mature technologies was used to accomplish the measurement. This report documents the results of development testing performed at Sandia to assure the instrumentation will withstand the severe environments present in the waste tanks.

  13. Test Results for LHC Insertion Region Dipole Magnets

    CERN Document Server

    Muratore, Joseph F; Cozzolino, John P; Ganetis, George; Ghosh, Arup; Gupta, Ramesh C; Harrison, Michael; Kumar-Jain, Animesh; Marone, Andrew; Richard-Plate, Stephen; Schmalzle, Jesse D; Thomas, Richard A; Wanderer, Peter; Willen, Erich; Wu, Kuo-Chen

    2005-01-01

    The Superconducting Magnet Division at Brookhaven National Laboratory (BNL) has made 20 insertion region dipoles for the Large Hadron Collider (LHC) at CERN. These 9.45 m-long, 8 cm aperture magnets have the same coil design as the arc dipoles now operating in the Relativistic Heavy Ion Collider (RHIC) at BNL and are of single aperture, twin aperture, and double cold mass configurations. They produce fields up to 3.8 T for operation at 7.56 TeV. Eighteen of these magnets have been tested at 4.5 K using either forced flow supercritical helium or liquid helium. The testing was especially important for the twin aperture models, which have the most challenging design. In these, the dipole fields in both apertures point in the same direction, unlike LHC arc dipoles. This paper reports on the results of these tests, including spontaneous quench performance, verification of quench protection heater operation, and magnetic field quality. Magnetic field measurements were done at 4.5K and at room temperature, and warm-...

  14. The ethical significance of diagnostic test results in psychology practice.

    Science.gov (United States)

    Shefler, Gaby; Ben Shakhar, Gershon; Bilu, Yoram

    2009-03-01

    "Psychologists base the opinions contained in their recommendations, reports and diagnostic or evaluative statements including forensic testimony on information and techniques sufficient to substantiate their findings". Do expert psychodiagnosticians rely in their professional final reports on the materials and raw data obtained from test materials? How ethical are they in their professional performances? In order to answer this question, expert clinical psychologists were given batteries of psychodiagnostic tests, accompanied by one of two different types of background information, suggesting either a Borderline Personality Disorder, or a Paranoid Personality Disorder. This background information was a full and strongly suggestive story in one experiment, and a mere hypothesis in another. All conditions manifested a confirmation bias: the psychodiagnostic reports were profoundly biased by the background suggestions. The present paper focuses on a content analysis of the reports, and shows that the experts referred very little if at all to the psychodiagnostic materials they received. They were found less professional and as a result- less ethical. The ethical relevance of these findings to the teaching and training of professional psychodiagnosticians is discussed, with an emphasis on the importance of teaching students and interns in clinical psychology to base their diagnostic reports on the test data.

  15. Aerodynamic and Acoustic Flight Test Results and Results for the Stratospheric Observatory for Infrared Astronomy

    Science.gov (United States)

    Cumming, Stephen B.; Smith, Mark S.; Cliatt, Larry J.; Frederick, Michael A.

    2014-01-01

    As part of the Stratospheric Observatory for Infrared Astronomy program, a 747SP airplane was modified to carry a 2.5-m telescope in the aft section of the fuselage. The resulting airborne observatory allows for observations above 99 percent of the water vapor in the atmosphere. The open cavity created by the modifications had the potential to significantly affect the airplane in the areas of aerodynamics and acoustics. Several series of flight tests were conducted to clear the operating envelope of the airplane for astronomical observations, planned to be performed between the altitudes of 35,000 ft and 45,000 ft. The flight tests were successfully completed. Cavity acoustics were below design limits, and the overall acoustic characteristics of the cavity were better than expected. The modification did have some effects on the stability and control of the airplane, but these effects were not significant. Airplane air data systems were not affected by the modifications. This paper describes the methods used to examine the aerodynamics and acoustic data from the flight tests and provides a discussion of the flight-test results in the areas of cavity acoustics, stability and control, and air data.

  16. Tc-99 Adsorption on Selected Activated Carbons - Batch Testing Results

    Energy Technology Data Exchange (ETDEWEB)

    Mattigod, Shas V.; Wellman, Dawn M.; Golovich, Elizabeth C.; Cordova, Elsa A.; Smith, Ronald M.

    2010-12-01

    CH2M HILL Plateau Remediation Company (CHPRC) is currently developing a 200-West Area groundwater pump-and-treat system as the remedial action selected under the Comprehensive Environmental Response, Compensation, and Liability Act Record of Decision for Operable Unit (OU) 200-ZP-1. This report documents the results of treatability tests Pacific Northwest National Laboratory researchers conducted to quantify the ability of selected activated carbon products (or carbons) to adsorb technetium-99 (Tc-99) from 200-West Area groundwater. The Tc-99 adsorption performance of seven activated carbons (J177601 Calgon Fitrasorb 400, J177606 Siemens AC1230AWC, J177609 Carbon Resources CR-1240-AW, J177611 General Carbon GC20X50, J177612 Norit GAC830, J177613 Norit GAC830, and J177617 Nucon LW1230) were evaluated using water from well 299-W19-36. Four of the best performing carbons (J177606 Siemens AC1230AWC, J177609 Carbon Resources CR-1240-AW, J177611 General Carbon GC20X50, and J177613 Norit GAC830) were selected for batch isotherm testing. The batch isotherm tests on four of the selected carbons indicated that under lower nitrate concentration conditions (382 mg/L), Kd values ranged from 6,000 to 20,000 mL/g. In comparison. Under higher nitrate (750 mg/L) conditions, there was a measureable decrease in Tc-99 adsorption with Kd values ranging from 3,000 to 7,000 mL/g. The adsorption data fit both the Langmuir and the Freundlich equations. Supplemental tests were conducted using the two carbons that demonstrated the highest adsorption capacity to resolve the issue of the best fit isotherm. These tests indicated that Langmuir isotherms provided the best fit for Tc-99 adsorption under low nitrate concentration conditions. At the design basis concentration of Tc 0.865 µg/L(14,700 pCi/L), the predicted Kd values from using Langmuir isotherm constants were 5,980 mL/g and 6,870 mL/g for for the two carbons. These Kd values did not meet the target Kd value of 9,000 mL/g. Tests

  17. Operational Results of a Closed Brayton Cycle Test-Loop

    Science.gov (United States)

    Wright, Steven A.; Fuller, Robert; Lipinski, Ronald J.; Nichols, Kenneth; Brown, Nicholas

    2005-02-01

    A number of space and terrestrial power system designs plan to use nuclear reactors that are coupled to Closed-loop Brayton Cycle (CBC) systems to generate electrical power. Because very little experience exists regarding the operational behavior of these systems, Sandia National Laboratories (through its Laboratory Directed Research and Development program) is developing a closed-loop test bed that can be used to determine the operational behavior of these systems and to validate models for these systems. Sandia has contracted Barber-Nichols Corporation to design, fabricate, and assemble a Closed-loop Brayton Cycle (CBC) system. This system was developed by modifying commercially available hardware. It uses a 30 kWe Capstone C-30 gas-turbine unit (www.capstoneturbine.com) with a modified housing that permits the attachment of an electrical heater and a water cooled chiller that are connected to the turbo-machinery in a closed loop. The test-loop reuses the Capstone turbine, compressor, and alternator. The Capstone system's nominal operating point is 1150 K turbine inlet temperature at 96,000 rpm. The annular recuperator and portions of the Capstone control system (inverter) and starter system are also reused. The rotational speed of the turbo-machinery is controlled either by adjusting the alternator load by either using the electrical grid or a separate load bank. This report describes the test-loop hardware SBL-30 (Sandia Brayton Loop-30kWe). Also presented are results of early testing and modeling of the unit. The SBL-30 hardware is currently configured with a heater that is limited to 80 kWth with a maximum outlet temperature of ˜1000 K.

  18. Flight Test 4 Preliminary Results: NASA Ames SSI

    Science.gov (United States)

    Isaacson, Doug; Gong, Chester; Reardon, Scott; Santiago, Confesor

    2016-01-01

    Realization of the expected proliferation of Unmanned Aircraft System (UAS) operations in the National Airspace System (NAS) depends on the development and validation of performance standards for UAS Detect and Avoid (DAA) Systems. The RTCA Special Committee 228 is charged with leading the development of draft Minimum Operational Performance Standards (MOPS) for UAS DAA Systems. NASA, as a participating member of RTCA SC-228 is committed to supporting the development and validation of draft requirements as well as the safety substantiation and end-to-end assessment of DAA system performance. The Unmanned Aircraft System (UAS) Integration into the National Airspace System (NAS) Project conducted flight test program, referred to as Flight Test 4, at Armstrong Flight Research Center from April -June 2016. Part of the test flights were dedicated to the NASA Ames-developed Detect and Avoid (DAA) System referred to as JADEM (Java Architecture for DAA Extensibility and Modeling). The encounter scenarios, which involved NASA's Ikhana UAS and a manned intruder aircraft, were designed to collect data on DAA system performance in real-world conditions and uncertainties with four different surveillance sensor systems. Flight test 4 has four objectives: (1) validate DAA requirements in stressing cases that drive MOPS requirements, including: high-speed cooperative intruder, low-speed non-cooperative intruder, high vertical closure rate encounter, and Mode CS-only intruder (i.e. without ADS-B), (2) validate TCASDAA alerting and guidance interoperability concept in the presence of realistic sensor, tracking and navigational errors and in multiple-intruder encounters against both cooperative and non-cooperative intruders, (3) validate Well Clear Recovery guidance in the presence of realistic sensor, tracking and navigational errors, and (4) validate DAA alerting and guidance requirements in the presence of realistic sensor, tracking and navigational errors. The results will be

  19. Results from laboratory and field testing of nitrate measuring spectrophotometers

    Science.gov (United States)

    Snazelle, Teri T.

    2015-01-01

    Five ultraviolet (UV) spectrophotometer nitrate analyzers were evaluated by the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility (HIF) during a two-phase evaluation. In Phase I, the TriOS ProPs (10-millimeter (mm) path length), Hach NITRATAX plus sc (5-mm path length), Satlantic Submersible UV Nitrate Analyzer (SUNA, 10-mm path length), and S::CAN Spectro::lyser (5-mm path length) were evaluated in the HIF Water-Quality Servicing Laboratory to determine the validity of the manufacturer's technical specifications for accuracy, limit of linearity (LOL), drift, and range of operating temperature. Accuracy specifications were met in the TriOS, Hach, and SUNA. The stock calibration of the S::CAN required two offset adjustments before the analyzer met the manufacturer's accuracy specification. Instrument drift was observed only in the S::CAN and was the result of leaching from the optical path insert seals. All tested models, except for the Hach, met their specified LOL in the laboratory testing. The Hach's range was found to be approximately 18 milligrams nitrogen per liter (mg-N/L) and not the manufacturer-specified 25 mg-N/L. Measurements by all of the tested analyzers showed signs of hysteresis in the operating temperature tests. Only the SUNA measurements demonstrated excessive noise and instability in temperatures above 20 degrees Celsius (°C). The SUNA analyzer was returned to the manufacturer at the completion of the Phase II field deployment evaluation for repair and recalibration, and the performance of the sensor improved significantly.

  20. Test results of high-precision large cryogenic lens holders

    Science.gov (United States)

    Gal, C.; Reutlinger, A.; Boesz, A.; Leberle, T.; Mottaghibonab, A.; Eckert, P.; Dubowy, M.; Gebler, H.; Grupp, F.; Geis, N.; Bode, A.; Katterloher, R.; Bender, R.

    2012-09-01

    For the Euclid mission a Pre-Development phase is implemented to prove feasibility of individual components of the system [1]. The Near Infrared Spectrometer and Photometer (NISP) of EUCLID requires high precision large lens holders (?170 mm) at cryogenic temperatures (150K). The four lenses of the optical system are made of different materials: fused silica, CaF2, and LF5G15 that are mounted in a separate lens barrel design. Each lens has its separate mechanical interface to the lens barrel, the so called adaption ring. The performance of the lens holder design is verified by adapted test equipment and test facility including an optical metrology system. The characterization of the lens deformation and displacement (decenter, tilt) due to mechanical loads of the holder itself as well as thermally induced loads are driven by the required submicron precision range and the operational thermal condition. The surface deformation of the lens and its holder is verified by interferometric measurements, while tilt and position accuracy are measured by in-situ fibre based distance sensors. The selected distance measurement sensors have the capability to measure in a few mm range with submicron resolution in ultra high vacuum, in vibration environments and at liquid nitrogen temperatures and below. The calibration of the measurement system is of crucial importance: impacts such as temperature fluctuation, surface roughness, surface reflectivity, straylight effects, etc. on the measured distance are carefully calibrated. Inbuilt thermal expansion effects of the fibre sensors are characterized and proven with lens dummy with quasi zero CTE. The paper presents the test results and measured performance of the high precision large cryogenic lens holders attained by the metrology system. These results are presented on behalf of the EUCLID consortium.

  1. The Space Station Photovoltaic Panels Plasma Interaction Test Program: Test plan and results

    Science.gov (United States)

    Nahra, Henry K.; Felder, Marian C.; Sater, Bernard L.; Staskus, John V.

    1989-01-01

    The Plasma Interaction Test performed on two space station solar array panels is addressed. This includes a discussion of the test requirements, test plan, experimental set-up, and test results. It was found that parasitic current collection was insignificant (0.3 percent of the solar array delivered power). The measured arcing threshold ranged from -210 to -457 V with respect to the plasma potential. Furthermore, the dynamic response of the panels showed the panel time constant to range between 1 and 5 microsec, and the panel capacitance to be between .01 and .02 microF.

  2. The Space Station photovoltaic panels plasma interaction test program - Test plan and results

    Science.gov (United States)

    Nahra, Henry K.; Felder, Marian C.; Sater, Bernard L.; Staskus, John V.

    1990-01-01

    The plasma Interaction Test performed on two space station solar array panels is addressed. This includes a discussion of the test requirements, test plan, experimental set-up, and test results. It was found that parasitic current collection was insignificant (0.3 percent of the solar array delivered power). The measured arcing threshold ranged from -210 to -457 V with respect to the plasma potential. Furthermore, the dynamic response of the panels showed the panel time constant to range between 1 and 5 microsec, and the panel capacitance to be between .01 and .02 microF.

  3. Comparison of FEA Calculations with Cryostat Dummy Weight Test Results

    CERN Document Server

    Guarino, V

    2004-01-01

    Extensive Finite Element analyses were performed to determine the loads and stresses acting on the EB and Barrel during assembly and in its final configuration. Up to now it has been difficult to verify the FEA results due to the unusual compression at the inner radius shims has resulted in larger than anticipated deflections. The cryostat dummy load test offers the first real chance for a direct comparison between the deflections of the Tilecal and the FEA model. By comparing the difference in position of the FM's before the cryostat load was applied and afterwards it is possible to eliminate all other variables and compare directly with the FEA model. This paper will present a comparison between the FEA model and the survey measurements for when the cryostat dummy weight load was applied at 32 modules and 46 modules in place.

  4. JWST tunable filter imager: etalon prototype test results

    Science.gov (United States)

    Touahri, D.; Cameron, P.; Evans, C.; Greenberg, E.; Rowlands, N.; Scott, A.; Doyon, R.; Beaulieu, M.; Djazovski, O.

    2008-07-01

    We present the prototyping results and laboratory characterization of a narrow band Fabry-Perot etalon flight model which is one of the wavelength selecting elements of the Tunable Filter Imager. The latter is a part of the Fine Guidance Sensor which represents the Canadian contribution to NASA's James Webb Space Telescope. The unique design of this etalon provides the JWST observatory with the ability to image at 30 Kelvin, a 2.2'x2.2' portion of its field of view in a narrow spectral bandwidth of R~100 at any wavelength ranging between 1.6 and 4.9 μm (with a gap in coverage between 2.5 and 3.2 μm). Extensive testing has resulted in better understanding of the thermal properties of the piezoelectric transducers used as an actuation system for the etalon gap tuning. Good throughput, spectral resolution and contrast have been demonstrated for the full wavelength range.

  5. Fan Noise Source Diagnostic Test: LDV Measured Flow Field Results

    Science.gov (United States)

    Podboy, Gary C.; Krupar, Martin J.; Hughes, Christopher E.; Woodward, Richard P.

    2003-01-01

    Results are presented of an experiment conducted to investigate potential sources of noise in the flow developed by two 22-in. diameter turbofan models. The R4 and M5 rotors that were tested were designed to operate at nominal take-off speeds of 12,657 and 14,064 RPMC, respectively. Both fans were tested with a common set of swept stators installed downstream of the rotors. Detailed measurements of the flows generated by the two were made using a laser Doppler velocimeter system. The wake flows generated by the two rotors are illustrated through a series of contour plots. These show that the two wake flows are quite different, especially in the tip region. These data are used to explain some of the differences in the rotor/stator interaction noise generated by the two fan stages. In addition to these wake data, measurements were also made in the R4 rotor blade passages. These results illustrate the tip flow development within the blade passages, its migration downstream, and (at high rotor speeds) its merging with the blade wake of the adjacent (following) blade. Data also depict the variation of this tip flow with tip clearance. Data obtained within the rotor blade passages at high rotational speeds illustrate the variation of the mean shock position across the different blade passages.

  6. TMED-4 INTERIM REPORT PURE ZR EQUILIBRIUM TEST RESULTS

    Energy Technology Data Exchange (ETDEWEB)

    Korinko, P.; Morgan, G.

    2010-12-17

    Due to higher than expected permeation rates in the production of tritium in the TVA, a development and testing program was implemented to develop the understanding of why the higher rates were occurring. In addition, improved data are needed for both the design as well as the predictive models. One part of the program was to determine the equilibrium pressure of hydrogen and tritium over NPZ (1). During the course of this testing, some curious results were discovered (2) compared to the published literature data (3). Due to these apparently results, a follow-on task was undertaken to determine the equilibrium pressure of protium and deuterium over pure zirconium. A series of experiments were conducted to determine equilibrium pressures and isotherm data for the zirconium - protium and zirconium - deuterium systems. The data match the published literature data reasonably well with the plateau extending to loadings of about 1.4. There is a significant pressure rise for loadings greater than 1.7.

  7. School results and access test results as indicators of first-year performance at university

    Directory of Open Access Journals (Sweden)

    A Bothma

    2004-06-01

    Full Text Available The goals set by the National Plan for Higher Education, the fact that many schools are still severely disadvantaged as well as far-reaching changes in the school system demand that South African universities urgently reconsider their admission procedures. Redesigning admission procedures calls for a thorough understanding of the interrelationships between school marks, results in existing access tests and first-year university performance. These interrelationships were statistically investigated in the case of the 1999, 2000 and 2001 intake groups, who were compelled to write access tests before being admitted to Stellenbosch University. The results of this investigation confirm an alarming degree of unpreparedness among many prospective students regarding what is expected of them at university. This is aggravated by school marks creating a totally unrealistic expectation of performance in the first year at university. It is emphasised that schools and authorities dealing with admission of prospective students at universities should be cognisant of the findings reported here. Furthermore, the statistical analyses demonstrate several novel techniques for investigating the interrelationship between school marks, access test results and university performance.

  8. Results of the mole penetration tests in different materials

    Science.gov (United States)

    Wawrzaszek, Roman; Seweryn, Karol; Grygorczuk, Jerzy; Banaszkiewicz, Marek; Rybus, Tomasz; Wisniewski, Lukasz; Neal, Clive R.; Huang, Shaopeng

    2010-05-01

    . Influence of the material compaction on the mole progress was also investigated. For these tests the small testbed has been used. It allowed us to test our mole penetrator up to the depth of 0.5 meters. Obtained results show that 'KRET' is able to penetrate even compacted lunar regolith simulant CHENOBI with minimum progress rate about 2mm per stroke. Moreover, we have confirmed that the mole works properly in both materials with low and high cohesion.

  9. Identification of source velocities on 3D structures in non-anechoic environments: Theoretical background and experimental validation of the inverse patch transfer functions method

    Science.gov (United States)

    Aucejo, M.; Totaro, N.; Guyader, J.-L.

    2010-08-01

    In noise control, identification of the source velocity field remains a major problem open to investigation. Consequently, methods such as nearfield acoustical holography (NAH), principal source projection, the inverse frequency response function and hybrid NAH have been developed. However, these methods require free field conditions that are often difficult to achieve in practice. This article presents an alternative method known as inverse patch transfer functions, designed to identify source velocities and developed in the framework of the European SILENCE project. This method is based on the definition of a virtual cavity, the double measurement of the pressure and particle velocity fields on the aperture surfaces of this volume, divided into elementary areas called patches and the inversion of impedances matrices, numerically computed from a modal basis obtained by FEM. Theoretically, the method is applicable to sources with complex 3D geometries and measurements can be carried out in a non-anechoic environment even in the presence of other stationary sources outside the virtual cavity. In the present paper, the theoretical background of the iPTF method is described and the results (numerical and experimental) for a source with simple geometry (two baffled pistons driven in antiphase) are presented and discussed.

  10. Polygraph Test Results Assessment by Regression Analysis Methods

    Directory of Open Access Journals (Sweden)

    K. A. Leontiev

    2014-01-01

    Full Text Available The paper considers a problem of defining the importance of asked questions for the examinee under judicial and psychophysiological polygraph examination by methods of mathematical statistics. It offers the classification algorithm based on the logistic regression as an optimum Bayesian classifier, considering weight coefficients of information for the polygraph-recorded physiological parameters with no condition for independence of the measured signs.Actually, binary classification is executed by results of polygraph examination with preliminary normalization and standardization of primary results, with check of a hypothesis that distribution of obtained data is normal, as well as with calculation of coefficients of linear regression between input values and responses by method of maximum likelihood. Further, the logistic curve divided signs into two classes of the "significant" and "insignificant" type.Efficiency of model is estimated by means of the ROC analysis (Receiver Operator Characteristics. It is shown that necessary minimum sample has to contain results of 45 measurements at least. This approach ensures a reliable result provided that an expert-polygraphologist possesses sufficient qualification and follows testing techniques.

  11. MATISSE: alignment, integration, and test phase first results

    Science.gov (United States)

    Allouche, F.; Robbe-Dubois, S.; Lagarde, S.; Cruzalèbes, P.; Antonelli, P.; Bresson, Y.; Fantei-Caujolle, Y.; Marcotto, A.; Morel, S.; Beckmann, U.; Bettonvil, F.; Berio, Ph.; Heininger, M.; Lehmitz, M.; Agocs, T.; Brast, R.; Elswijk, E.; Ives, D.; Meixner, K.; Laun, W.; Mellein, M.; Neumann, U.; Bailet, C.; Clausse, J.-M.; Matter, A.; Meilland, A.; Millour, F.; Petrov, R. G.; Accardo, M.; Bristow, P.; Frahm, R.; Glindemann, A.; Gonzáles Herrera, J.-C.; Lizon, J.-L.; Schöller, M.; Graser, U.; Jaffe, W.; Lopez, B.

    2016-08-01

    MATISSE (Multi AperTure mid-Infrared SpectroScopic Experiment) is the spectro-interferometer for the VLTI of the European Southern Observatory, operating in near and mid-infrared, and combining up to four beams from the unit or the auxiliary telescopes. MATISSE will offer new breakthroughs in the study of circumstellar environments by allowing the multispectral mapping of the material distribution, the gas and essentially the dust. The instrument consists in a warm optical system (WOP) accepting four optical beams and relaying them after a dichroic splitting (for the L and M- and N- spectral bands) to cold optical benches (COB) located in two separate cryostats. The Observatoire de la Côte d'Azur is in charge of the WOP providing the spectral band separation, optical path equalization and modulation, pupil positioning, beam anamorphosis, beam commutation, and calibration. NOVA-ASTRON is in charge of the COB providing the functions of beam selection, reduction of thermal background emission, spatial filtering, pupil transfer, photometry and interferometry splitting, additional beam anamorphosis, spectral filtering, polarization selection, image dispersion, and image combination. The Max Planck Institut für Radio Astronomie is in charge of the operation and performance validation of the two detectors, a HAWAII-2RG from Teledyne for the L- and M- bands and a Raytheon AQUARIUS for the N-band. Both detectors are provided by ESO. The Max Planck Institut für Astronomie is in charge of the electronics and the cryostats for which the requirements on space limitations and vibration stability resulted on very specific and stringent decisions on the design. The integration and test of the COB: the two cryogenic systems, including the cold benches and the detectors, have been conducted at MPIA in parallel with the integration of the WOP at OCA. At the end of 2014, the complete instrument was integrated at OCA. Following this integration, a period of interface and alignment

  12. Fission Surface Power Technology Demonstration Unit Test Results

    Science.gov (United States)

    Briggs, Maxwell H.; Gibson, Marc A.; Geng, Steven M.; Sanzi, James L.

    2016-01-01

    The Fission Surface Power (FSP) Technology Demonstration Unit (TDU) is a system-level demonstration of fission power technology intended for use on manned missions to Mars. The Baseline FSP systems consists of a 190 kWt UO2 fast-spectrum reactor cooled by a primary pumped liquid metal loop. This liquid metal loop transfers heat to two intermediate liquid metal loops designed to isolate fission products in the primary loop from the balance of plant. The intermediate liquid metal loops transfer heat to four Stirling Power Conversion Units (PCU), each of which produce 12 kWe (48 kW total) and reject waste heat to two pumped water loops, which transfer the waste heat to titanium-water heat pipe radiators. The FSP TDU simulates a single leg of the baseline FSP system using an electrically heater core simulator, a single liquid metal loop, a single PCU, and a pumped water loop which rejects the waste heat to a Facility Cooling System (FCS). When operated at the nominal operating conditions (modified for low liquid metal flow) during TDU testing the PCU produced 8.9 kW of power at an efficiency of 21.7 percent resulting in a net system power of 8.1 kW and a system level efficiency of 17.2 percent. The reduction in PCU power from levels seen during electrically heated testing is the result of insufficient heat transfer from the NaK heater head to the Stirling acceptor, which could not be tested at Sunpower prior to delivery to the NASA Glenn Research Center (GRC). The maximum PCU power of 10.4 kW was achieved at the maximum liquid metal temperature of 875 K, minimum water temperature of 350 K, 1.1 kg/s liquid metal flow, 0.39 kg/s water flow, and 15.0 mm amplitude at an efficiency of 23.3 percent. This resulted in a system net power of 9.7 kW and a system efficiency of 18.7 percent.

  13. Test Results and Comparison of Triaxial Strength Testing of Waste Isolation Pilot Plant Clean Salt

    Energy Technology Data Exchange (ETDEWEB)

    Buchholz, Stuart A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-12-01

    This memorandum documents laboratory thermomechanical triaxial strength testing of Waste Isolation Pilot Plant (WIPP) clean salt. The limited study completed independent, adjunct laboratory tests in the United States to assist in validating similar testing results being provided by the German facilities. The testing protocol consisted of completing confined triaxial, constant strain rate strength tests of intact WIPP clean salt at temperatures of 25°C and 100°C and at multiple confining pressures. The stratigraphy at WIPP also includes salt that has been labeled “argillaceous.” The much larger test matrix conducted in Germany included both the so-called clean and argillaceous salts. When combined, the total database of laboratory results will be used to develop input parameters for models, assess adequacy of existing models, and predict material behavior. These laboratory studies are also consistent with the goals of the international salt repository research program. The goal of this study was to complete a subset of a test matrix on clean salt from the WIPP undertaken by German research groups. The work was performed at RESPEC in Rapid City, South Dakota. A rigorous Quality Assurance protocol was applied, such that corroboration provides the potential of qualifying all of the test data gathered by German research groups.

  14. Surrogate/spent fuel sabotage : aerosol ratio test program and Phase 2 test results.

    Energy Technology Data Exchange (ETDEWEB)

    Borek, Theodore Thaddeus III; Thompson, N. Slater (U.S. Department of Energy); Sorenson, Ken Bryce; Hibbs, R.S. (U.S. Department of Energy); Nolte, Oliver (Fraunhofer Institut fur Toxikologie und Experimentelle Medizin, Germany); Molecke, Martin Alan; Autrusson, Bruno (Institut de Radioprotection et de Surete Nucleaire, France); Young, F. I. (U.S. Nuclear Regulatory Commission); Koch, Wolfgang (Fraunhofer Institut fur Toxikologie und Experimentelle Medizin, Germany); Brochard, Didier (Institut de Radioprotection et de Surete Nucleaire, France); Pretzsch, Gunter Guido (Gesellschaft fur Anlagen- und Reaktorsicherheit, Germany); Lange, Florentin (Gesellschaft fur Anlagen- und Reaktorsicherheit, Germany)

    2004-05-01

    A multinational test program is in progress to quantify the aerosol particulates produced when a high energy density device, HEDD, impacts surrogate material and actual spent fuel test rodlets. This program provides needed data that are relevant to some sabotage scenarios in relation to spent fuel transport and storage casks, and associated risk assessments; the program also provides significant political benefits in international cooperation. We are quantifying the spent fuel ratio, SFR, the ratio of the aerosol particles released from HEDD-impacted actual spent fuel to the aerosol particles produced from surrogate materials, measured under closely matched test conditions. In addition, we are measuring the amounts, nuclide content, size distribution of the released aerosol materials, and enhanced sorption of volatile fission product nuclides onto specific aerosol particle size fractions. These data are crucial for predicting radiological impacts. This document includes a thorough description of the test program, including the current, detailed test plan, concept and design, plus a description of all test components, and requirements for future components and related nuclear facility needs. It also serves as a program status report as of the end of FY 2003. All available test results, observations, and analyses - primarily for surrogate material Phase 2 tests using cerium oxide sintered ceramic pellets are included. This spent fuel sabotage - aerosol test program is coordinated with the international Working Group for Sabotage Concerns of Transport and Storage Casks, WGSTSC, and supported by both the U.S. Department of Energy and Nuclear Regulatory Commission.

  15. Results of MPBX studies at the single heater test

    Energy Technology Data Exchange (ETDEWEB)

    Blair, S. C.,LLNL

    1997-10-01

    We have developed an extensometer for measurement of distance and displacements in a geologic repository for high-level nuclear waste. This is an optical extensometer that measures distance using a modulated laser beam. In this design, reflecting targets are placed at desired measurement locations, and distance between each target and an optical head are measured repeatedly using the modulated laser beam. Moreover, all electronic and moving parts are located outside of the hostile or difficult environment as the optical head is connected to the laser, switching and signal analysis hardware using optical fibers. A reference beam is utilized to provide direct correction of system behavior. `Be system also - utilizes movable reflective anchors that can be repositioned if desired. We have installed the system in the Single Heater Test being conducted in Alcove 5 of the Exploratory Studies Facility at Yucca Mountain, and report preliminary results.

  16. Results from the Exoplanet Search Programmes with BEST and TEST

    CERN Document Server

    Eislöffel, J; Rauer, H; Voss, H; Erikson, A; Eigmueller, P; Günther, E; Eisloeffel, Jochen; Hatzes, Artie P.; Rauer, Heike; Voss, Holger; Erikson, Anders; Eigmueller, Philipp; Guenther, Eike

    2006-01-01

    Thueringer Landessternwarte Tautenburg (TLS) has started to operate a small dedicated telescope - the Tautenburg Exoplanet Search Telescope (TEST) - searching for transits of extrasolar planets in photometric time series observations. In a joint effort with the Berlin Exoplanet Search Telescope (BEST) operated by the Institut fuer Planetenforschung of the "Deutsches Zentrum fuer Luft- und Raumfahrt (DLR)" at the Observatoire de Haute-Provence (OHP), France, two observing sites are used to optimise transit search. Here, we give a short overview of these systems and the data analysis. We describe a software pipeline that we have set up to identify transit events of extrasolar planets and variable stars in time series data from these and other telescopes, and report on some first results.

  17. Channel Modelling for Multiprobe Over-the-Air MIMO Testing

    Directory of Open Access Journals (Sweden)

    Pekka Kyösti

    2012-01-01

    a fading emulator, an anechoic chamber, and multiple probes. Creation of a propagation environment inside an anechoic chamber requires unconventional radio channel modelling, namely, a specific mapping of the original models onto the probe antennas. We introduce two novel methods to generate fading emulator channel coefficients; the prefaded signals synthesis and the plane wave synthesis. To verify both methods we present a set of simulation results. We also show that the geometric description is a prerequisite for the original channel model.

  18. Acoustic conditions in open plan offices – Pilot test results

    Directory of Open Access Journals (Sweden)

    Witold Mikulski

    2016-10-01

    Full Text Available Background: The main source of noise in open plan office are conversations. Office work standards in such premises are attained by applying specific acoustic adaptation. This article presents the results of pilot tests and acoustic evaluation of open space rooms. Material and Methods: Acoustic properties of 6 open plan office rooms were the subject of the tests. Evaluation parameters, measurement methods and criterial values were adopted according to the following standards: PN-EN ISO 3382- 3:2012, PN-EN ISO 3382-2:2010, PN-B-02151-4:2015-06 and PN-B-02151-3:2015-10. Results: The reverberation time was 0.33– 0.55 s (maximum permissible value in offices – 0.6 s; the criterion was met, sound absorption coefficient in relation to 1 m2 of the room’s plan was 0.77–1.58 m2 (minimum permissible value – 1.1 m2; 2 out of 6 rooms met the criterion, distraction distance was 8.5–14 m (maximum permissible value – 5 m; none of the rooms met the criterion, A-weighted sound pressure level of speech at a distance of 4 m was 43.8–54.7 dB (maximum permissible value – 48 dB; 2 out of 6 rooms met the criterion, spatial decay rate of the speech was 1.8–6.3 dB (minimum permissible value – 7 dB; none of the rooms met the criterion. Conclusions: Standard acoustic treatment, containing sound absorbing suspended ceiling, sound absorbing materials on the walls, carpet flooring and sound absorbing workplace barriers, is not sufficient. These rooms require specific advanced acoustic solutions. Med Pr 2016;67(5:653–662

  19. Results of Thyroid Function Tests in Premature Infants

    Directory of Open Access Journals (Sweden)

    Pelin Doğan

    2016-04-01

    Full Text Available Introduction: To determine the rate, etiology and morbidity association of disorders of thyroid function tests (TFTs in premature babies. Materials and Methods: A total of 139 premature babies who were admitted to Uludag University Faculty of Medicine Hospital Neonatal Intensive Care Unit between January 2009 and January 2012 were included in this study. Prenatal, natal and postnatal characteristics along with TFTs results were recorded. TFTs were performed for all patients in the first and third weeks of life. Thyroid stimulation hormone (TSH values of >10 IU/L was considered elevated. Free T3 and T4 levels were evaluated according to laboratory cut-off values. Weight, height and head circumference values of all individuals with and without the diagnosis of hypothyroidism on the 6th, 12th, and 18th months of their polyclinic follow-ups.Results: Abnormal TFTs were detected in 41 (24% patients. Twenty two patients (53% had transient TSH elevation, 9 (22% had primary hypothyroidism, 9 (22% had non-thyroidal disease and 1 (2.4% had transient hypothyroxinemia. Among morbidities, respiratory distress syndrome rate was found to be significantly higher in patients with thyroid function disorders (p=0.007. The rate of thyroid function disorders in patients with mothers with hypothyroidism was significantly more frequent compared to patients without maternal hypothyroidism (p=0.049. The mean head circumference in 18 month was significantly lower in patients with abnormal TFTs (p=0.047. Conclusions: Thyroid function disorders are common morbidities in premature babies and are important for neuromotor development. Maternal thyroid function disorder can lead to impairment of TFTs in infants. Thyroid function tests should be performed in all premature babies and hypotyhroidism should be treated. Avoidance of iodine exposure in premature infants can reduce the rate of abnormal TFTs and transient hypothyroidism.

  20. Results of Detailed Hydrologic Characterization Tests - Fiscal Year 2000

    Energy Technology Data Exchange (ETDEWEB)

    Spane, Frank A.; Thorne, Paul D.; Newcomer, Darrell R.

    2001-05-15

    This report provides the resluts of detailed hydrologic characterization tests conducted within eleven Hanford Site wells during fiscal year 2000. Detailed characterization tests performed included groundwater-flow characterization; barometric response evaluation; slug tests; single-well tracer tests; constant-rate pumping tests; and in-well, vertical flow tests. Hydraulic property estimates obtained from the detailed hydrologic tests include transmissivity; hydraulic conductivity; specific yield; effective porosity; in-well, lateral flow velocity; aquifer-flow velocity; vertical distribution of hydraulic conductivity (within the well-screen section); and in-well, verticla flow velocity. In addition, local groundwater-flow characteristics (i.e., hydraulic gradient and flow direction) were determined for four sites where detailed well testing was performed.

  1. Nonlinear Analysis and Preliminary Testing Results of a Hybrid Wing Body Center Section Test Article

    Science.gov (United States)

    Przekop, Adam; Jegley, Dawn C.; Rouse, Marshall; Lovejoy, Andrew E.; Wu, Hsi-Yung T.

    2015-01-01

    A large test article was recently designed, analyzed, fabricated, and successfully tested up to the representative design ultimate loads to demonstrate that stiffened composite panels with through-the-thickness reinforcement are a viable option for the next generation large transport category aircraft, including non-conventional configurations such as the hybrid wing body. This paper focuses on finite element analysis and test data correlation of the hybrid wing body center section test article under mechanical, pressure and combined load conditions. Good agreement between predictive nonlinear finite element analysis and test data is found. Results indicate that a geometrically nonlinear analysis is needed to accurately capture the behavior of the non-circular pressurized and highly-stressed structure when the design approach permits local buckling.

  2. A blast absorber test: measurement and model results

    NARCIS (Netherlands)

    Eerden, F.J.M. van der; Berg, F. van den; Hof, J. van 't; Arkel, E. van

    2006-01-01

    A blast absorber test was conducted at the Aberdeen Test Centre from 13 to 17 June 2005. The test was set up to determine the absorbing and shielding effect of a gravel pile, of 1.5 meters high and 15 by 15 meters wide, on blasts from large weapons: e.g. armor, artillery or demolition. The blast was

  3. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Pilot-Scale Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Gary M. Blythe

    2006-03-01

    - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High Sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. This topical report presents the results from the Task 2 and Task 4 pilot-scale additive tests. The Task 3 and Task 5 full-scale additive tests will be conducted later in calendar year 2006.

  4. Pre-course Results from the Astronomy Diagnostic Test

    Science.gov (United States)

    Hufnagel, Beth; Slater, Timothy; Deming, Grace; Adams, Jeff; Adrian, Rebecca L.; Brick, Christine; Zeilik, Michael

    2000-08-01

    We present selected results from the January 1999 semester pre-course administration of the Astronomy Diagnostic Test (ADT), a research-based, multiple-choice instrument that assesses student knowledge and understanding about selected concepts in astronomy. The ADT is valid for undergraduate non-science majors taking an introductory astronomy course. This paper briefly summarises the development and validation processes, which included pre-course administration to 1557 students in 22 classes attending 17 various post-secondary institutions across the USA in the January 1999 semester. Two interesting results of the ADT's pre-course administration are (1) the average class score of the ADT is about the same (32%) regardless of type of post-secondary institution or class size and (2) there is a significant gender difference, with women scoring an average of 28% and men 38%, with the standard errors both less than 1%. The current version of the ADT (Version 2 dated 21 June 1999) and a comparative by-class database is available to astronomy instructors at the (USA) Association of Astronomy Educators' and the National Institute for Science Education's (NISE) WebPages.

  5. 2011 Hyundai Sonata 4932 - Hybrid Electric Vehicle Battery Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Tyler Gray; Matthew Shirk; Jeffrey Wishart

    2013-07-01

    The U.S. Department of Energy Advanced Vehicle Testing Activity Program consists of vehicle, battery, and infrastructure testing on advanced technology related to transportation. The activity includes tests on hybrid electric vehicles (HEVs), including testing the HEV batteries when both the vehicles and batteries are new and at the conclusion of 160,000 miles of on-road fleet testing. This report documents battery testing performed for the 2011 Hyundai Sonata Hybrid HEV (VIN KMHEC4A43BA004932). Battery testing was performed by the Electric Transportation Engineering Corporation dba ECOtality North America. The Idaho National Laboratory and ECOtality North America collaborate on the AVTA for the Vehicle Technologies Program of the DOE.

  6. Automated Critical Peak Pricing Field Tests: Program Descriptionand Results

    Energy Technology Data Exchange (ETDEWEB)

    Piette, Mary Ann; Watson, David; Motegi, Naoya; Kiliccote, Sila; Xu, Peng

    2006-04-06

    California utilities have been exploring the use of critical peak prices (CPP) to help reduce needle peaks in customer end-use loads. CPP is a form of price-responsive demand response (DR). Recent experience has shown that customers have limited knowledge of how to operate their facilities in order to reduce their electricity costs under CPP (Quantum 2004). While the lack of knowledge about how to develop and implement DR control strategies is a barrier to participation in DR programs like CPP, another barrier is the lack of automation of DR systems. During 2003 and 2004, the PIER Demand Response Research Center (DRRC) conducted a series of tests of fully automated electric demand response (Auto-DR) at 18 facilities. Overall, the average of the site-specific average coincident demand reductions was 8% from a variety of building types and facilities. Many electricity customers have suggested that automation will help them institutionalize their electric demand savings and improve their overall response and DR repeatability. This report focuses on and discusses the specific results of the Automated Critical Peak Pricing (Auto-CPP, a specific type of Auto-DR) tests that took place during 2005, which build on the automated demand response (Auto-DR) research conducted through PIER and the DRRC in 2003 and 2004. The long-term goal of this project is to understand the technical opportunities of automating demand response and to remove technical and market impediments to large-scale implementation of automated demand response (Auto-DR) in buildings and industry. A second goal of this research is to understand and identify best practices for DR strategies and opportunities. The specific objectives of the Automated Critical Peak Pricing test were as follows: (1) Demonstrate how an automated notification system for critical peak pricing can be used in large commercial facilities for demand response (DR). (2) Evaluate effectiveness of such a system. (3) Determine how customers

  7. Augmented dry cooling surface test program: analysis and experimental results

    Energy Technology Data Exchange (ETDEWEB)

    Parry, H.L.; MacGowan, L.J.; Kreid, D.K.; Wiles, L.E.; Faletti, D.W.; Johnson, B.M.

    1979-09-01

    Experiments were performed to assess the operating characteristics and potential performance of water-augmented dry cooling systems. The work was aimed at evaluating a deluged air-cooled HOETERV plate fin heat exchanger surface proposed for integrated dry/wet cooling systems and using test results to guide the development of a predictive analytical model. In the process, all-dry performance data were obtained for the HOETERV surface as well as for two Curtiss-Wright chipped fin surfaces. The dry heat transfer data indicate that a slotted Curtiss-Wright surface slightly outperforms the HOETERV and nonslotted Curtiss-Wright surfaces based on heat rejection rate per unit of fan power. However, all three surfaces are so close in performance that other factors, such as surface cost and piping and mounting costs, will probably determine which surface is preferred at a given installation. Comparisons of deluged HOETERV performance with dry HOETERV and Curtiss-Wright performance under prototypic conditions have established that deluging can provide considerable heat rejection enhancement, particularly at low ITD and low air humidity. A deluged HOETERV core operating at a 115/sup 0/F primary fluid temperature in 105/sup 0/F air at 10% relative humidity can reject over 7 times as much heat as a dry HOETERV core operating under the same conditions at the same air-side pressure drop. Deluged tests were performed to evaluate the effect of airflow rate, deluge flow rate and core tilt angle on performance. Both increased airflow and increased deluge flow increase both heat rejection rate and required fan power. Optimal airflow rate will thus be determined for a given location by the competing costs of heat exchanger surface area versus fan operation. Changes in core tilt angle from vertical to 16/sup 0/ from vertical have a negligible effect on performance.

  8. Tests of composite materials at cryogenic temperatures facilities and results

    CERN Document Server

    Dahlerup-Petersen, K

    1980-01-01

    The design and installation of test facilities for the determination of macromechanical and thermal properties of fiber-reinforced polymer materials at temperatures down to 4.2K are presented. Construction and performance details are given for the following test equipment: quasi- static-tensile and compression-test facilities equipped with an automatic data acquisition system for calculation of material properties, deformation characteristics and various statistics; a thermal contraction-expansion measuring system; a thermal conductivity measurement cell. (1 refs).

  9. Fan Noise Source Diagnostic Test: Vane Unsteady Pressure Results

    Science.gov (United States)

    Envia, Edmane

    2002-01-01

    To investigate the nature of fan outlet guide vane pressure fluctuations and their link to rotor-stator interaction noise, time histories of vane fluctuating pressures were digitally acquired as part of the Fan Noise Source Diagnostic Test. Vane unsteady pressures were measured at seven fan tip speeds for both a radial and a swept vane configuration. Using time-domain averaging and spectral analysis, the blade passing frequency (BPF) harmonic and broadband contents of the vane pressures were individually analyzed. Significant Sound Pressure Level (SPL) reductions were observed for the swept vane relative to the radial vane for the BPF harmonics of vane pressure, but vane broadband reductions due to sweep turned out to be much smaller especially on an average basis. Cross-correlation analysis was used to establish the level of spatial coherence of broadband pressures between different locations on the vane and integral length scales of pressure fluctuations were estimated from these correlations. Two main results of this work are: (1) the average broadband level on the vane (in dB) increases linearly with the fan tip speed for both the radial and swept vanes, and (2) the broadband pressure distribution on the vane is nearly homogeneous and its integral length scale is a monotonically decreasing function of fan tip speed.

  10. [Human basophil degranulation test. Results of a modified technic (I)].

    Science.gov (United States)

    Román Pérez, F; Berlanga Cortés, J A; Urquiă, M; Guerra Pasadas, F; Peña Martínez, J

    1986-01-01

    The degranulation of human basophils towards antigenic substances, to which they must be previously sensitized as a result of the antigen-antibody union at the membrane level, is a phenomenon that has an important application complementing diagnosis of diseases mediated by the Gell and Coombs classification of Type I Hypersensitivity, on which the principle of Human Basophils Degranulation Test (HBDT) was based. An essential requirement is to be able to collect an adequate quantity of basophils, as well as the visualization by means of a technique of convenient stain. In this work, we show a modified HBDT technique for basophil granulocytes staining. A total of 33 HBDT was carried out on patients sensitive to grass pollen and/or Olea europea pollen and/or D. pteronyssinus, and as controls, HBDT was done on healthy individuals with negative clinical history. Basophil enrichemnt from the circulating blood sample was done by means of centrifugation in Percoll density gradients of 1072, 1076, 1080 and 1082, and we obtained a higher number of basophils with a density of 1080 at 400 Xg for 30 minutes. The cellular bottom was resuspended in 600 microliters of PBS. We employed lyophilized antigenic extracts from grass pollen, Olea europea and D. pteronyssinus, employing weight/volume concentration of 10(-4), 10(-5), 10(-6) and 10(-7). The optimum dilutions were 10(-5) for grass pollen and D. pteronyssinus.

  11. Results and Analysis from Space Suit Joint Torque Testing

    Science.gov (United States)

    Matty, Jennifer E.; Aitchison, Lindsay

    2009-01-01

    A space suit s mobility is critical to an astronaut s ability to perform work efficiently. As mobility increases, the astronaut can perform tasks for longer durations with less fatigue. The term mobility, with respect to space suits, is defined in terms of two key components: joint range of motion and joint torque. Individually these measures describe the path which in which a joint travels and the force required to move it through that path. Previous space suits mobility requirements were defined as the collective result of these two measures and verified by the completion of discrete functional tasks. While a valid way to impose mobility requirements, such a method does necessitate a solid understanding of the operational scenarios in which the final suit will be performing. Because the Constellation space suit system requirements are being finalized with a relatively immature concept of operations, the Space Suit Element team elected to define mobility in terms of its constituent parts to increase the likelihood that the future pressure garment will be mobile enough to enable a broad scope of undefined exploration activities. The range of motion requirements were defined by measuring the ranges of motion test subjects achieved while performing a series of joint maximizing tasks in a variety of flight and prototype space suits. The definition of joint torque requirements has proved more elusive. NASA evaluated several different approaches to the problem before deciding to generate requirements based on unmanned joint torque evaluations of six different space suit configurations being articulated through 16 separate joint movements. This paper discusses the experiment design, data analysis and results, and the process used to determine the final values for the Constellation pressure garment joint torque requirements.

  12. Cone Penetrometer Load Cell Temperature and Radiation Testing Results

    Energy Technology Data Exchange (ETDEWEB)

    Follett, Jordan R.

    2013-08-28

    This report summarizes testing activities performed at the Pacific Northwest National Laboratory to verify the cone penetrometer load cell can withstand the tank conditions present in 241-AN-101 and 241-AN-106. The tests demonstrated the load cell device will operate under the elevated temperature and radiation levels expected to be encountered during tank farm deployment of the device.

  13. Separation of radiated sound field components from waves scattered by a source under non-anechoic conditions

    DEFF Research Database (Denmark)

    Fernandez Grande, Efren; Jacobsen, Finn

    2010-01-01

    A method of estimating the sound field radiated by a source under non-anechoic conditions has been examined. The method uses near field acoustic holography based on a combination of pressure and particle velocity measurements in a plane near the source for separating outgoing and ingoing wave...... components. The outgoing part of the sound field is composed of both radiated and scattered waves. The method compensates for the scattered components of the outgoing field on the basis of the boundary condition of the problem, exploiting the fact that the sound field is reconstructed very close...... to the source. Thus the radiated free-field component is estimated simultaneously with solving the inverse problem of reconstructing the sound field near the source. The method is particularly suited to cases in which the overall contribution of reflected sound in the measurement plane is significant....

  14. Results of a 1462 hour ammonia arcjet endurance test

    Science.gov (United States)

    Polk, J. E.; Goodfellow, K. D.

    1992-07-01

    A total of 1462 hours of operaton were demonstrated in an endurance test of a 30 kWe-class ammonia arcjet operated at 10 kWe. The propellant flow rate was 0.170 g/s, and the measured performance increased from approximately 650 s specific impulse at 36 percent efficiency at the beginning of the test to 675 s at 39 percent near the end. The voltage increased and the current dropped slightly over the first 400 hours, and then remained approximately constant for the remainder of the test. The test, scheduled for 1500 hours, was terminated after an insulator in the rear of the engine failed. Post-test examination of the electrodes revealed only minimal damage. Although there was evidence of a number of mass transport processes occurring in the discharge chamber, the primary life-limiting wear mechanisms appear to be cathode tip erosion and constrictor melting.

  15. Test results of chemical reactivity test (CRT) analysis of structural materials and explosives

    Energy Technology Data Exchange (ETDEWEB)

    Back, P.S.; Barnhart, B.V.; Walters, R.R.; Haws, L.D.; Collins, L.W.

    1980-03-21

    The chemical reactivity test, CRT, is a procedure used to screen the compatibility of component structure materials with explosives. This report contains the results of CRT materials evaluations conducted at Mound Facility. Data about materials combinations are catalogued both under the name of the explosive and the nonexplosive.

  16. Triaxial and Torsional Shear Test Results for Sand

    Science.gov (United States)

    1994-06-01

    densest and loosest packing of particles without crushing the grains. The standard test methods ASTM D4253-83 and D4254-83 were used to determine the...desired value of J (J = = I( j.2/+ 2 was reached. The sample was then sheared with a constant value of J. The mean norma stress p was held constant while oz...Triaxial Testing System", Advanced Triaxial Testing of Soil and Rock, ASTM , STP77, 1988, PP95-106. Miura, K, Miura, S. and Told, S., "Deformation Behavior

  17. Can clinical colour vision tests be used to predict the results of the Farnsworth lantern test?

    Science.gov (United States)

    Cole, B L; Maddocks, J D

    1998-11-01

    Clinicians usually do not have access to a lantern test when making an occupational assessment of the ability of a person with defective colour vision to recognise signal light colours: they must rely on the results of ordinary clinical tests. While all colour vision defectives fail the Holmes Wright Type B lantern test and most fail the Holmes Wright Type A lantern, 35% of colour vision defectives pass the Farnsworth lantern. Can clinical tests predict who will pass and fail the Farnsworth lantern? We find that a pass (less than two or more diametrical crossings) at the Farnsworth Panel D 15 Dichotomous test has a sensitivity of 0.67 and specificity of 0.94 in predicting a pass or fail at the Farnsworth lantern test: a Nagel range of > 10 has a sensitivity of 0.87 and a specificity of 0.57. We conclude that neither the D 15 nor the Nagel Anomaloscope matching range are satisfactory predictors of performance on the Farnsworth Lantern.

  18. Preliminary test results from the CELSS Test Facility Engineering Development Unit

    Science.gov (United States)

    Kliss, Mark H.; Macelroy, R. D.; Blackwell, C. C.; Borchers, B. A.; Drews, M. E.; Longabaugh, J. R.; Yendler, B. S.; Zografos, A. I.

    1994-01-01

    As part of the NASA Controlled Ecological Life Support System (CELSS) Program, a CELSS Test Facility (CTF) is being planned for installation on the Space Station. The CTF will be used to provide data on the productivity and efficiency of a variety of CELSS higher plant crops grown in the microgravity environment of the Space Station. Tight environmental control will be maintained while data on gas exchange rates and biomass accumulation rates are collected. In order to obtain an early realistic determination of the subsystem and system requirements necessary to provide the environmental conditions specified for CTF crop productivity experiments, an Engineering Development Unit (EDU) has been designed, constructed and is in the process of subsystem and system testing at NASA Ames Research Center. The EDU is a ground test-bed which will be used to characterize the integrated performance of major subsystem technologies, to evaluate hardware candidates and control strategies required for the CTF, and to further define the ability to meet CTF requirements within present Space Station constraints. This paper reviews the functional requirements for the EDU, and focuses on the performance evaluation and test results of the various subsystems. Preliminary integrated performance results and control system operation are addressed, and plans for future science and technology testing are discussed.

  19. Factors Resulting in Micron Indentation Hardness Descending in Indentation Tests

    Institute of Scientific and Technical Information of China (English)

    Li Min; Chen Weimin

    2009-01-01

    hardness decrease can be bated if the continuous stiffness measurement technique is not adopted; this indicates that the test method itself may also be one of the factors causing the hardness being descended.

  20. CHALLENGE TESTS WITH LISTERIA MONOCYTOGENES IN SALAMI: PRELIMINARY RESULTS

    Directory of Open Access Journals (Sweden)

    R. Mioni

    2013-02-01

    Full Text Available Challenge tests are the preferable methodology to study the behaviour of Listeria monocytogenes on ready to eat foods, according to Regulation (EC 2073/2005. Challenge testing using L. monocytogenes in seasoned salami from different food business operators showed, after seasoning of the product, a count reduction of the inoculated organisms without any further growth of the pathogen; however differences of L. monocytogenes behaviour could be observed according to different production protocols.

  1. U.S. field testing programs and results

    Energy Technology Data Exchange (ETDEWEB)

    Wicks, G.G.

    2000-06-09

    The United States has been active in four major international in-situ or field testing programs over the past two decades, involving the burial of simulated high-level waste forms and package components. These programs are designed to supplement laboratory testing studies in order to obtain the most complete and realistic picture possible of waste glass behavior under realistic repository-relevant conditions.

  2. Results of thermal test of metallic molybdenum disk target and fast-acting valve testing

    Energy Technology Data Exchange (ETDEWEB)

    Virgo, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Chemerisov, S. [Argonne National Lab. (ANL), Argonne, IL (United States); Gromov, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Jonah, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, G. F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-12-01

    This report describes the irradiation conditions for thermal testing of helium-cooled metallic disk targets that was conducted on March 9, 2016, at the Argonne National Laboratory electron linac. The four disks in this irradiation were pressed and sintered by Oak Ridge National Laboratory from molybdenum metal powder. Two of those disks were instrumented with thermocouples. Also reported are results of testing a fast-acting-valve system, which was designed to protect the accelerator in case of a target-window failure.

  3. Clinical patterns and results of radioallergosorbent test (RAST) and skin tests in penicillin allergy.

    Science.gov (United States)

    Kraft, D; Wide, L

    1976-06-01

    Seventy-nine patients with acute or former reactions to penicillin were investigated by a benzylpenicilloyl (BPO)-specific RAST and/or by skin tests with penicilloyl-polylysine (PPL), benzylpenicillin and penicilloic acid and the results were correlated with the different clinical pictures. Positive RAST and skin test results could be found in patients with anaphylactic shock, urticaria and serum sickness-like reaction and sometimes in a special group of exanthems, which are characterized by the existence of many different lesions at the same time, therefore called 'polymorphic exanthems', and often observed after high-dosage penicillin therapy. In cases of scarlatiniform or morbilliform exanthems no positive results were found. The BPO-specific RAST showed an overall correlation of 95-I% with skin tests using PPL. However, some patients with positive skin tests to benzylpenicillin and penicilloic acid did no have detectable circulating IgE antibodies to BPO. This emphasizes the need for including these antigens in in vitro methods. The RAST was informative even at the allergic reaction or in the first 15 days afterwards and seems to be very valuable for early diagnosis of penicillin allergy especially in cases when many drugs have been given.

  4. Hypervelocity Impact Test Results for a Metallic Thermal Protection System

    Science.gov (United States)

    Karr, Katherine L.; Poteet, Carl C.; Blosser, Max L.

    2003-01-01

    Hypervelocity impact tests have been performed on specimens representing metallic thermal protection systems (TPS) developed at NASA Langley Research Center for use on next-generation reusable launch vehicles (RLV). The majority of the specimens tested consists of a foil gauge exterior honeycomb panel, composed of either Inconel 617 or Ti-6Al-4V, backed with 2.0 in. of fibrous insulation and a final Ti-6Al-4V foil layer. Other tested specimens include titanium multi-wall sandwich coupons as well as TPS using a second honeycomb sandwich in place of the foil backing. Hypervelocity impact tests were performed at the NASA Marshall Space Flight Center Orbital Debris Simulation Facility. An improved test fixture was designed and fabricated to hold specimens firmly in place during impact. Projectile diameter, honeycomb sandwich material, honeycomb sandwich facesheet thickness, and honeycomb core cell size were examined to determine the influence of TPS configuration on the level of protection provided to the substructure (crew, cabin, fuel tank, etc.) against micrometeoroid or orbit debris impacts. Pictures and descriptions of the damage to each specimen are included.

  5. ESO adaptive optics facility progress and first laboratory test results

    Science.gov (United States)

    Arsenault, Robin; Madec, Pierre-Yves; Paufique, Jérome; La Penna, Paolo; Stroebele, Stefan; Vernet, Elise; Pirard, Jean-Francois; Hackenberg, Wolfgang; Kuntschner, Harald; Kolb, Johann; Muller, Nicolas; Garcia-Rissmann, Aurea; Le Louarn, Miska; Amico, Paola; Hubin, Norbert; Lizon, Jean-Louis; Ridings, Rob; Haguenauer, Pierre; Abad, Jose A.; Fischer, Gerhard; Heinz, Volker; Kiekebusch, Mario; Argomedo, Javier; Conzelmann, Ralf; Tordo, Sebastien; Donaldson, Rob; Soenke, Christian; Duhoux, Philippe; Fedrigo, Enrico; Delabre, Bernard; Jost, Andrea; Duchateau, Michel; Downing, Mark; Reyes Moreno, Javier; Manescau, Antonio; Bonaccini Calia, Domenico; Quattri, Marco; Dupuy, Christophe; Guidolin, Ivan M.; Comin, Mauro; Guzman, Ronald; Buzzoni, Bernard; Quentin, Jutta; Lewis, Steffan; Jolley, Paul; Kraus, Max; Pfrommer, Thomas; Biasi, Roberto; Gallieni, Daniele; Stuik, Remko; Kaenders, Wilhelm; Ernstberger, Bernhard; Friedenauer, Axel

    2014-07-01

    The Adaptive Optics Facility project is completing the integration of its systems at ESO Headquarters in Garching. The main test bench ASSIST and the 2nd Generation M2-Unit (hosting the Deformable Secondary Mirror) have been granted acceptance late 2012. The DSM has undergone a series of tests on ASSIST in 2013 which have validated its optical performance and launched the System Test Phase of the AOF. This has been followed by the performance evaluation of the GRAAL natural guide star mode on-axis and will continue in 2014 with its Ground Layer AO mode. The GALACSI module (for MUSE) Wide-Field-Mode (GLAO) and the more challenging Narrow-Field-Mode (LTAO) will then be tested. The AOF has also taken delivery of the second scientific thin shell mirror and the first 22 Watt Sodium laser Unit. We will report on the system tests status, the performances evaluated on the ASSIST bench and advancement of the 4Laser Guide Star Facility. We will also present the near future plans for commissioning on the telescope and some considerations on tools to ensure an efficient operation of the Facility in Paranal.

  6. Hunter standoff killer team (HSKT) ground and flight test results

    Science.gov (United States)

    Moreland, Balinda; Ennis, Mark; Yeates, Robert; Condon, Timothy

    2007-04-01

    Warfighter's Associate (WA) which was integrated onto the Apache Longbow, and the Mobile Commanders Associate (MCA) which was integrated onto the Army Airborne Command and Control System (A2C2S) UH-60 Blackhawk. In this paper we will discuss what WA and MCA provided to the warfighter, and the results of the HSKT ground and flight testing.

  7. CSI Flight Computer System and experimental test results

    Science.gov (United States)

    Sparks, Dean W., Jr.; Peri, F., Jr.; Schuler, P.

    1993-01-01

    This paper describes the CSI Computer System (CCS) and the experimental tests performed to validate its functionality. This system is comprised of two major components: the space flight qualified Excitation and Damping Subsystem (EDS) which performs controls calculations; and the Remote Interface Unit (RIU) which is used for data acquisition, transmission, and filtering. The flight-like RIU is the interface between the EDS and the sensors and actuators positioned on the particular structure under control. The EDS and RIU communicate over the MIL-STD-1553B, a space flight qualified bus. To test the CCS under realistic conditions, it was connected to the Phase-0 CSI Evolutionary Model (CEM) at NASA Langley Research Center. The following schematic shows how the CCS is connected to the CEM. Various tests were performed which validated the ability of the system to perform control/structures experiments.

  8. Performance of CREAM Calorimeter Results of Beam Tests

    CERN Document Server

    Ahn, H S; Beatty, J J; Bigongiari, G; Castellina, A; Childers, J T; Conklin, N B; Coutu, S; Duvernois, M A; Ganel, O; Han, J H; Hyun, H J; Kang, T G; Kim, H J; Kim, K C; Kim, M Y; Kim, T; Kim, Y J; Lee, J K; Lee, M H; Lutz, L; Maestro, P; Malinine, A; Marrocchesi, P S; Mognet, S I; Nam, S W; Nutter, S; Park, N H; Park, H; Seo, E S; Sina, R; Syed, S; Song, C; Swordy, S; Wu, J; Yang, J; Zhang, H Q; Zei, R; Zinn, S Y

    2005-01-01

    The Cosmic Ray Energetics And Mass (CREAM), a balloon-borne experiment, is under preparation for a flight in Antarctica at the end of 2004. CREAM is planned to measure the energy spectrum and composition of cosmic rays directly at energies between 1 TeV and 1000 TeV. Incident particle energies will be measured by a transition radiation detector and a sampling calorimeter. The calorimeter was constructed at the University of Maryland and tested at CERN in 2003. Performance of the calorimeter during the beam tests is reported.

  9. Results of Laboratory Testing of Advanced Power Strips

    Energy Technology Data Exchange (ETDEWEB)

    Earle, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sparn, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2012-08-01

    Presented at the ACEEE Summer Study on Energy Efficiency in Buildings on August 12-17, 2012, this presentation reports on laboratory tests of 20 currently available advanced power strip products, which reduce wasteful electricity use of miscellaneous electric loads in buildings.

  10. Preliminary Results of Breakwater Round-Head Tests

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Liu, Z.

    1995-01-01

    The rational design diagram for Dolos armour should incorporate both the hydraulic stability and the structural integrity. The previous tests performed by Aalborg University (AU) made available such design diagram for the trunk of Dolos breakwater without superstructures (Burcharth et al. 1992...

  11. Conventional Anchor Test Results at San Diego and Indian Island

    Science.gov (United States)

    1980-07-01

    lines passed through open chocks welded at opposite ends of the barge. A crane barge was used to install and recover all test anchors at each site...DEPT OF FISH & GAME Long Beach CA (Marine Tech Info Ctr) CALIF. DEPT OF NAVIGATION & OCEAN DEV. Sacramento, CA (G. Armstrong) CALIF. MARITIME ACADEMY

  12. Results of Caisson Breakwater Tests in Multidirectional Breaking Seas

    DEFF Research Database (Denmark)

    Kofoed, Jens Peter

    In extension of the work done at the Hydraulics and Coastal Engineering Laboratory, Dept. of Civil Engineering, Aalborg University, Denmark, described in Grønbech et al., 1997, laboratory tests has been performed investigating wave loading and overtopping on caisson breakwaters in multidirectional...

  13. TEST RESULTS FOR FUEL CELL OPERATION ON ANAEROBIC DIGESTER GAS

    Science.gov (United States)

    EPA, in conjunction with ONSI Corp., embarked on a project to define, design, test, and assess a fuel cell energy recovery system for application at anaerobic digester waste water (sewage) treatment plants. Anaerobic digester gas (ADG) is produced at these plants during the proce...

  14. Results of Statewide TerraNova Testing, Fall 1998.

    Science.gov (United States)

    La Marca, Paul M.

    This summary provides key findings about state, district, and school level performance on the TerraNova examinations (CTB/McGraw Hill) in Nevada in 1998-1999. The TerraNova tests are used to assess students in grades 4, 8, and 10 as stipulated by Nevada law. Within this summary, a description of performance as measured by national percentile…

  15. Laser Welding Test Results with Gas Atmospheres in Welding Chamber

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Chang-Young; Hong, Jin-Tae; Ahn, Sung-Ho; Heo, Sung-Ho; Jang, Seo-Yun; Yang, Tae-Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    The weld beads of specimens welded under identical conditions in the helium and argon gas were cleaner, more regular, and steadier than those in a vacuum. The penetration depth of the FZ in the vacuum was much deeper than those in the helium and argon gas. To measure the irradiation properties of nuclear fuel in a test reactor, a nuclear fuel test rod instrumented with various sensors must be fabricated with assembly processes. A laser welding system to assemble the nuclear fuel test rod was designed and fabricated to develop various welding technologies of the fuel test rods to joint between a cladding tube and end-caps. It is an air-cooling optical fiber type and its emission modes are a continuous (CW) mode of which the laser generates continuous emission, and pulse (QCW) mode in which the laser internally generates sequences of pulses. We considered the system welding a sample in a chamber that can weld a specimen in a vacuum and inert gas atmosphere, and the chamber was installed on the working plate of the laser welding system. In the chamber, the laser welding process should be conducted to have no defects on the sealing area between a cladding tube and an end-cap.

  16. Mechanical test results from the EU testing program for potential ITER insulation material

    Energy Technology Data Exchange (ETDEWEB)

    Broadbent, A.J.; Butt, S.; Smith, K.D. [Oxford Instruments, Witney (United Kingdom)] [and others

    1997-06-01

    Insulation systems will be a key element in the future construction and impregnation of the coils for the ITER device. Candidate materials must survive prolonged irradiation (2.5 x 10{sup 21} - 2.5 x 10{sup 22} neutrons/m{sup 2} - September 1994) simultaneous high compressive and shear stresses (up to 300 MPa and 50 MPa respectively), and have high electrical reliability (30 year service life). The materials chosen are intended to meet the demands of full scale coil manufacture. Mechanical properties, including shear / compression and compression at cryogenic temperatures of several different insulation systems are reported. The mechanically acceptable systems will be irradiation tested at a future date, although only materials believed to withstand high irradiation doses have been selected. The final results of this program are presented and compared with a pass / fail criterion based on results from a benchmark testing program (insulation system based on anhydride cured DGEBA resin and S2 glass).

  17. Analysis of behaviour of transonic profiles with strong curvature: Test facilities, instrumentation, test results, theoretical interpretations

    Energy Technology Data Exchange (ETDEWEB)

    Pittaluga, G.; Benvenuto, G. (Udine Univ. (Italy); L' Aquila Univ. (Italy))

    1988-06-01

    Relevant to experimental investigations on the performance of a transonic turbine blade cascade, this paper discusses recent developments regarding the following topics: the experimental equipment and relative instrumentation; the results of tests on turbine blade cascades; the conceptual methods specifically developed and aimed at the optimized design of steam turbines systems and turbine blades; the theoretical-numerical procedures developed and applied as supports for theoretical-experimental analyses and the redesign of blade profiles to increase efficiency.

  18. Results from Carbon Dioxide Washout Testing Using a Suited Manikin Test Apparatus with a Space Suit Ventilation Test Loop

    Science.gov (United States)

    Chullen, Cinda; Conger, Bruce; McMillin, Summer; Vonau, Walt; Kanne, Bryan; Korona, Adam; Swickrath, Mike

    2016-01-01

    NASA is developing an advanced portable life support system (PLSS) to meet the needs of a new NASA advanced space suit. The PLSS is one of the most critical aspects of the space suit providing the necessary oxygen, ventilation, and thermal protection for an astronaut performing a spacewalk. The ventilation subsystem in the PLSS must provide sufficient carbon dioxide (CO2) removal and ensure that the CO2 is washed away from the oronasal region of the astronaut. CO2 washout is a term used to describe the mechanism by which CO2 levels are controlled within the helmet to limit the concentration of CO2 inhaled by the astronaut. Accumulation of CO2 in the helmet or throughout the ventilation loop could cause the suited astronaut to experience hypercapnia (excessive carbon dioxide in the blood). A suited manikin test apparatus (SMTA) integrated with a space suit ventilation test loop was designed, developed, and assembled at NASA in order to experimentally validate adequate CO2 removal throughout the PLSS ventilation subsystem and to quantify CO2 washout performance under various conditions. The test results from this integrated system will be used to validate analytical models and augment human testing. This paper presents the system integration of the PLSS ventilation test loop with the SMTA including the newly developed regenerative Rapid Cycle Amine component used for CO2 removal and tidal breathing capability to emulate the human. The testing and analytical results of the integrated system are presented along with future work.

  19. 3D silicon pixel sensors: Recent test beam results

    CERN Document Server

    Hansson, P; Sandaker, H; Korolkov, I; Barrera, C; Wermes, N; Borri, M; Grinstein, S; Troyano, I; Grenier, P; Devetak, E; Fleta, C; Kenney, C; Tsybychev, D; Nellist, C; Chmeissan, M; Su, D; DeWilde, B; Silverstein, D; Dorholt, O; Tsung, J; Sjoebaek, K; Stupak, J; Slaviec, T; Micelli, A; Helle, K; Bolle, E; Huegging, F; Kocian, M; Fazio, S; Balbuena, J; Dalla Betta, G F; La Rosa, A; Rivero, F; Mastroberardino, A; Hasi, J; Darbo, G; Boscardin, M; Da Via, C; Nordahl, P; Giordani, M; Jackson, P; Rohne, O; Gemme, C; Young, C

    2011-01-01

    The 3D silicon sensors aimed for the ATLAS pixel detector upgrade have been tested with a high energy pion beam at the CERN SPS in 2009. Two types of sensor layouts were tested: full-3D assemblies fabricated in Stanford, where the electrodes penetrate the entire silicon wafer thickness, and modified-3D assemblies fabricated at FBK-irst with partially overlapping electrodes. In both cases three read-out electrodes are ganged together to form pixels of dimension 50 x 400 mu m(2). Data on the pulse height distribution, tracking efficiency and resolution were collected for various particle incident angles, with and without a 1.6 T magnetic field. Data from a planar sensor of the type presently used in the ATLAS detector were used at the same time to give comparison. Published by Elsevier B.V.

  20. 3D silicon pixel sensors: Recent test beam results

    Energy Technology Data Exchange (ETDEWEB)

    Hansson, P., E-mail: phansson@cern.c [University of Oslo (Norway); Balbuena, J.; Barrera, C. [CNM Barcelona (Spain); Bolle, E. [University of Oslo (Norway); Borri, M. [Torino University (Italy); Boscardin, M. [FBK Trento (Italy); Chmeissan, M. [IFAE Barcelona (Spain); Dalla Betta, G.-F. [Universita di Trento and INFN Trento (Italy); Darbo, G. [INFN Genova (Italy); Da Via, C. [University of Manchester (United Kingdom); Devetak, E.; DeWilde, B. [Stony Brook University (United States); Su, D. [SLAC (United States); Dorholt, O. [University of Oslo (Norway); Fazio, S. [Calabria University (Italy); Fleta, C. [CNM Barcelona (Spain); Gemme, C. [INFN Genova (Italy); Giordani, M. [University of Udine and INFN Udine (Italy); Gjersdal, H. [University of Oslo (Norway); Grenier, P. [SLAC (United States)

    2011-02-01

    The 3D silicon sensors aimed for the ATLAS pixel detector upgrade have been tested with a high energy pion beam at the CERN SPS in 2009. Two types of sensor layouts were tested: full-3D assemblies fabricated in Stanford, where the electrodes penetrate the entire silicon wafer thickness, and modified-3D assemblies fabricated at FBK-irst with partially overlapping electrodes. In both cases three read-out electrodes are ganged together to form pixels of dimension 50x400{mu}m{sup 2}. Data on the pulse height distribution, tracking efficiency and resolution were collected for various particle incident angles, with and without a 1.6 T magnetic field. Data from a planar sensor of the type presently used in the ATLAS detector were used at the same time to give comparison.

  1. Design and preliminary test results of Daya Bay RPC modules

    Institute of Scientific and Technical Information of China (English)

    XU Ji-Lei; Logan Lebanowski; Cullen Newsom; Lin Shih-Kai; Jonathan Link; MA Lie-Hua; Viktor Pě(c); Vit Vorobel; CHEN Jin; LIU Jin-Chang; ZHOU Yong-Zhao; GUAN Meng-Yun; LIANG Hao; YANG Chang-Gen; WANG Yi-Fang; ZHANG Jia-Wen; LU Chang-Guo; Kirk McDonald; Robert Hackenburg; Kwong Lau

    2011-01-01

    Resistive Plate Chamber(RPC)modules will be used as one part of the cosmic muon veto system in the Days Bay reactor neutrino experiment.A total of 189 RPC modules will cover the three water pools in the experiment.To achieve track reconstruction and high efficiency,each module consists of 4 layers,each of which contains two sizes of bare chambers.The placement of bare chambers is reversed in different layers to reduce the overlapping dead areas.The module efficiency and patch efficiency were studied both in simulation and test of the data analysis.143 modules have been constructed and tested.The preliminary study shows that the module and patch 3 out of 4 layers efficiency reaches about 98%.

  2. HVEPS Scramjet-Driven MHD Power Demonstration Test Results (Preprint)

    Science.gov (United States)

    2007-06-01

    seeding for the scramjet- driven MHD demonstration test was accomplished by the injection of liquid NaK into the backplate of the UTRC pre-heater... NaK is a eutectic consisting of approximately 80% potassium and 20% sodium. It exists in liquid form at room temperature and has flow properties...quite similar to water. However, there are materials handling safety issues with use of NaK since it is highly caustic alkali metal and burns on

  3. Operating experiences and test results of six cold helium compressors

    Science.gov (United States)

    Brown, D. P.; Gibbs, R. J.; Schlafke, A. P.; Sondericker, J. H.; Wu, K. C.

    Three small and three large cold helium centrifugal compressors have been operated at Brookhaven National Laboratory between 1981 and 1986. The three small cold compressors have been installed on a 1000 W refrigerator for testing a string of superconducting magnets and for R and D purposes. The three large units are components of the BNL 24.8 KW refrigerator to be used to provide cooling for the RHIC project. These compressors are used either to circulate a large amount of supercritical helium through a group of magnets or to pump on the helium bath to reduce temperature in the system. One small circulating compressor tested employs tilting-pad gas bearings and is driven by a DC motor. The two small cold vacuum pumps tested use oil bearings and are driven by oil turbines. The three large oil-bearing cold compressors are driven by DC motors through a gear box. A unique feature of the large vacuum pump is the combination of two pumps with a total of four stages on the same shaft. The adiabatic efficiencies are found to be 57% for the large vacuum pumps and close to 50% for the large circulating compressor. Good overall reliability has been experienced.

  4. THE LT-CFB GASIFIER – FIRST TEST RESULTS FROM THE 500 KW TEST PLANT

    DEFF Research Database (Denmark)

    Nielsen, Rasmus Glar; Stoholm, Peder; Nielsen, Mads Brix

    2005-01-01

    The Low Temperature Circulating Fluidised Bed (LT-CFB) gasification process is briefly described together with the first test results from the new 500 kW test plant. The process aims primarily at co-firing low grade biomass and waste products at power plants and offer several advantages to directly...... co-firing: E.g. the ashes of different fuels can be kept separate, and corrosion and fouling of the furnace can be drastically reduced. Three fuels have been tested so far on this plant: High ash straw (12% ash, dry), dry matter from pig manure (28% ash, dry) and dry matter from biogas residue based...... on pig manure (44% ash, dry). All the tests have been very stable and a steady state content of ash components, e.g. potassium, in the ash and bed material was reached. The low temperature (max. 750°C) ensures that there are no agglomeration problems, and that almost 100% of K, Si, Ca and P is kept...

  5. Pseudomonas pellicle in disinfectant testing: electron microscopy, pellicle removal, and effect on test results.

    Science.gov (United States)

    Cole, E C; Rutala, W A; Carson, J L; Alfano, E M

    1989-01-01

    Pseudomonas aeruginosa ATCC 15442 is a required organism in the Association of Official Analytical Chemists use-dilution method for disinfectant efficacy testing. When grown in a liquid medium, P. aeruginosa produces a dense mat or pellicle at the broth/air interface. The purpose of this investigation was to examine the pellicle by scanning electron microscopy, to evaluate three pellicle removal methods, and to determine the effect of pellicle fragments on disinfectant efficacy test results. The efficacies of three methods of pellicle removal (decanting, vacuum suction, and filtration) were assessed by quantifying cell numbers on penicylinders. The Association of Official Analytical Chemists use-dilution method was used to determine whether pellicle fragments in the tubes used to inoculate penicylinders affected test results. Scanning electron micrographs showed the pellicle to be a dense mass of intact, interlacing cells at least 10 microns thick. No significant differences in pellicle removal methods were observed, and the presence of pellicle fragments usually increased the number of positive tubes in the use-dilution method significantly. Images PMID:2497711

  6. Autonomous Airborne Refueling Demonstration: Phase I Flight-Test Results

    Science.gov (United States)

    Dibley, Ryan P.; Allen, Michael J.; Nabaa, Nassib

    2007-01-01

    The first phase of the Autonomous Airborne Refueling Demonstration (AARD) project was completed on August 30, 2006. The goal of this 15-month effort was to develop and flight-test a system to demonstrate an autonomous refueling engagement using the Navy style hose-and-drogue air-to-air refueling method. The prime contractor for this Defense Advanced Research Projects Agency (DARPA) sponsored program was Sierra Nevada Corporation (SNC), Sparks, Nevada. The responsible flight-test organization was the National Aeronautics and Space Administration (NASA) Dryden Flight Research Center (DFRC), Edwards, California, which also provided the F/A-18 receiver airplane (McDonnell Douglas, now The Boeing Company, Chicago, Illinois). The B-707-300 tanker airplane (The Boeing Company) was contracted through Omega Aerial Refueling Services, Inc., Alexandria, Virginia, and the optical tracking system was contracted through OCTEC Ltd., Bracknell, Berkshire, United Kingdom. Nine research flights were flown, testing the functionality and performance of the system in a stepwise manner, culminating in the plug attempts on the final flight. Relative position keeping was found to be very stable and accurate. The receiver aircraft was capable of following the tanker aircraft through turns while maintaining its relative position. During the last flight, six capture attempts were made, two of which were successful. The four misses demonstrated excellent characteristics, the receiver retreating from the drogue in a controlled, safe, and predictable manner that precluded contact between the drogue and the receiver aircraft. The position of the receiver aircraft when engaged and in position for refueling was found to be 5.5 to 8.5 ft low of the ideal position. The controller inputs to the F/A-18 were found to be extremely small.

  7. Autonomous Airborne Refueling Demonstration, Phase I Flight-Test Results

    Science.gov (United States)

    Dibley, Ryan P.; Allen, Michael J.; Nabaa, Nassib

    2007-01-01

    The first phase of the Autonomous Airborne Refueling Demonstration (AARD) project was completed on August 30, 2006. The goal of this 15-month effort was to develop and flight-test a system to demonstrate an autonomous refueling engagement using the Navy style hose-and-drogue air-to-air refueling method. The prime contractor for this Defense Advanced Research Projects Agency (DARPA) sponsored program was Sierra Nevada Corporation (SNC), Sparks, Nevada. The responsible flight-test organization was the NASA Dryden Flight Research Center (DFRC), Edwards, California, which also provided the F/A-18 receiver airplane (McDonnell Douglas, now The Boeing Company, Chicago, Illinois). The B-707-300 tanker airplane (The Boeing Company) was contracted through Omega Aerial Refueling Services, Inc., Alexandria, Virginia, and the optical tracking system was contracted through OCTEC Ltd., Bracknell, Berkshire, United Kingdom. Nine research flights were flown, testing the functionality and performance of the system in a stepwise manner, culminating in the plug attempts on the final flight. Relative position keeping was found to be very stable and accurate. The receiver aircraft was capable of following the tanker aircraft through turns while maintaining its relative position. During the last flight, six capture attempts were made, two of which were successful. The four misses demonstrated excellent characteristics, the receiver retreating from the drogue in a controlled, safe, and predictable manner that precluded contact between the drogue and the receiver aircraft. The position of the receiver aircraft when engaged and in position for refueling was found to be 5.5 to 8.5 ft low of the ideal position. The controller inputs to the F/A-18 were found to be extremely small

  8. GPM Avionics Module Heat Pipes Design and Performance Test Results

    Science.gov (United States)

    Ottenstein, Laura; DeChristopher, Mike

    2012-01-01

    GPM is a satellite constellation to study precipitation formed from a partnership between NASA and the Japanese Aerospace Exploration Agency (JAXA). The GPM Core Observatory, being developed and tested at GSFC, serves as a reference standard to unify precipitation measurements from the GPM satellite constellation. The Core Observatory carries an advanced radar/radiometer system to measure precipitation from space. The scientific data gained from GPM will benefit both NASA and JAXA by advancing our understanding of Earth's water and energy cycle, improving forecasts of extreme weather events, and extending our current capabilities in using accurate and timely precipitation information to benefit society.

  9. AiResearch QCGAT engine: Acoustic test results

    Science.gov (United States)

    Kisner, L. S.

    1980-01-01

    The noise levels of the quiet, general aviation turbofan (QCGAT) engine were measured in ground static noise tests. The static noise levels were found to be markedly lower than the demonstrably quiet AiResearch model TFE731 engine. The measured QCGAT noise levels were correlated with analytical noise source predictions to derive free-field component noise predictions. These component noise sources were used to predict the QCGAT flyover noise levels at FAR Part 36 conditions. The predicted flyover noise levels are about 10 decibels lower than the current quietest business jets.

  10. Field Test: Results from the One Year Mission

    Science.gov (United States)

    Reschke, M. F.; Kozlovskaya, I. B.; Kofman, I. S.; Tomilovskaya, E. S.; Cerisano, J. M.; Rosenberg, M. J. F.; Bloomberg, J. J.; Stenger, M. B.; Lee, S. M. C.; Laurie, S. S.; Rukavishnikov, I. V.; Fomina, E. V.; Wood, S. J.; Mulavara, A. P.; Feiveson, A. H.; Fisher, E. A.; Phillips, T.; Ribeiro, C.; Taylor, L. C.; Miller, C. A.; Gadd, N. E.; Peters, B. T.; Kitov, V. V.; Lysova, N. Yu; Holden, K. L.; De Dios, Y.

    2017-01-01

    The One Year Mission was designed to aid in determining the effect that extending the duration on orbit aboard the International Space Station (ISS) would have on a number of biological and physiological systems. Two crewmembers were selected to participate in this endeavor, one U.S. On-Orbit Segment (USOS) astronaut and one Russian cosmonaut. The Neuroscience and Cardiovascular and Vision Laboratories at the Johnson Space Center and the Sensory-Motor and Countermeasures Division within the Institute for Biomedical Problems were selected to investigate vestibular, sensorimotor and cardiovascular function with the two long-duration crewmembers using the established methodology developed for the Field Test (FT).

  11. Hydrogeology and results of injection tests at waste-injection test sites in Pinellas County, Florida

    Science.gov (United States)

    Hickey, John J.

    1982-01-01

    Potential benefits or hazards to freshwater resources could result from subsurface injection of treated wastewater. Recognizing this, the U.S. Geological Survey, in cooperation with Pinellas County and the city of St. Petersburg, undertook an evaluation of the hydrogeology and injection of wastewater at proposed test sites on the Pinellas peninsula. The injection sites are underlain by sedimentary rocks ranging in age from Cretaceous to Pleistocene. Lower Eocene carbonate rocks were penetrated to a maximum depth of 3,504 feet and were found to have relatively low water yields. The most permeable part of the investigated section was in rocks of middle Eocene age within the Floridan aquifer. At the injection sites, the Floridan aquifer was subdivided into four permeable zones and three semiconfining beds. The test injection zone is within the Avon Park Limestone, the most productive of the identified permeable zones, with a transmissivity of about 1,000,000 feet squared per day. Two semiconfining beds are above the injection zone in the Suwannee Limestone and Ocala Limestone and have vertical hydraulic conductivities estimated to range from about 0.1 to 1 foot per day where these beds do not contain clay. Limited fresh ground-water supplies exist in the Floridan aquifer within the Pinellas peninsula. At all test sites, chloride concentration in the injection zone ranged from 19,000 to 20,000 milligrams per liter. Injection tests ranging in duration from 3 to 91.1 days were run at three different sites. Pressure buildup occurred in permeable zones above and below the injection zone during these tests. Calculated pressure buildup in observation wells close to and at some distance from the test wells was typically less than 1 pound per square inch. Injection and formation water will probably move slowly through the semiconfining bed overlying the injection zone, and long-term injection tests will be needed to determine the effectiveness of these beds to retard flow. The

  12. Hanford 100-D Area Biostimulation Treatability Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Truex, Michael J.; Vermeul, Vincent R.; Fritz, Brad G.; Mackley, Rob D.; Mendoza, Donaldo P.; Elmore, Rebecca P.; Mitroshkov, Alexandre V.; Sklarew, Deborah S.; Johnson, Christian D.; Oostrom, Martinus; Newcomer, Darrell R.; Brockman, Fred J.; Bilskis, Christina L.; Hubbard, Susan S.; Peterson, John E.; Williams, Kenneth H.; Gasperikova, E.; Ajo-Franklin, J.

    2009-09-30

    Pacific Northwest National Laboratory conducted a treatability test designed to demonstrate that in situ biostimulation can be applied to help meet cleanup goals in the Hanford Site 100-D Area. In situ biostimulation has been extensively researched and applied for aquifer remediation over the last 20 years for various contaminants. In situ biostimulation, in the context of this project, is the process of amending an aquifer with a substrate that induces growth and/or activity of indigenous bacteria for the purpose of inducing a desired reaction. For application at the 100-D Area, the purpose of biostimulation is to induce reduction of chromate, nitrate, and oxygen to remove these compounds from the groundwater. The in situ biostimulation technology is intended to provide supplemental treatment upgradient of the In Situ Redox Manipulation (ISRM) barrier previously installed in the Hanford 100-D Area and thereby increase the longevity of the ISRM barrier. Substrates for the treatability test were selected to provide information about two general approaches for establishing and maintaining an in situ permeable reactive barrier based on biological reactions, i.e., a biobarrier. These approaches included 1) use of a soluble (miscible) substrate that is relatively easy to distribute over a large areal extent, is inexpensive, and is expected to have moderate longevity; and 2) use of an immiscible substrate that can be distributed over a reasonable areal extent at a moderate cost and is expected to have increased longevity.

  13. GridPix detectors: Production and beam test results

    Energy Technology Data Exchange (ETDEWEB)

    Koppert, W.J.C., E-mail: wkoppert@nikhef.nl [Nikhef, Amsterdam (Netherlands); Bakel, N. van [Nikhef, Amsterdam (Netherlands); Bilevych, Y. [Physikalisches Institut, University of Bonn, Bonn (Germany); Colas, P. [IRFU, CEA Saclay, Gif-sur-Yvette (France); Desch, K. [Physikalisches Institut, University of Bonn, Bonn (Germany); Fransen, M.; Graaf, H. van der; Hartjes, F.; Hessey, N.P. [Nikhef, Amsterdam (Netherlands); Kaminski, J. [Physikalisches Institut, University of Bonn, Bonn (Germany); Schmitz, J. [University of Twente, Mesa Institute for Nanotechnology, Enschede (Netherlands); Schön, R.; Zappon, F. [Nikhef, Amsterdam (Netherlands)

    2013-12-21

    The innovative GridPix detector is a Time Projection Chamber (TPC) that is read out with a Timepix-1 pixel chip. By using wafer post-processing techniques an aluminium grid is placed on top of the chip. When operated, the electric field between the grid and the chip is sufficient to create electron induced avalanches which are detected by the pixels. The time-to-digital converter (TDC) records the drift time enabling the reconstruction of high precision 3D track segments. Recently GridPixes were produced on full wafer scale, to meet the demand for more reliable and cheaper devices in large quantities. In a recent beam test the contribution of both diffusion and time walk to the spatial and angular resolutions of a GridPix detector with a 1.2 mm drift gap are studied in detail. In addition long term tests show that in a significant fraction of the chips the protection layer successfully quenches discharges, preventing harm to the chip.

  14. Short-Term Test Results: Multifamily Home Energy Efficiency Retrofit

    Energy Technology Data Exchange (ETDEWEB)

    Lyons, J.

    2013-01-01

    Multifamily deep energy retrofits (DERs) represent great potential for energy savings, while also providing valuable insights on research-generated efficiency measures, cost-effectiveness metrics, and risk factor strategies for the multifamily housing industry. The Bay Ridge project is comprised of a base scope retrofit with a goal of achieving 30% savings (relative to pre-retrofit), and a DER scope with a goal of 50% savings (relative to pre-retrofit). The base scope has been applied to the entire complex, except for one 12-unit building which underwent the DER scope. Findings from the implementation, commissioning, and short-term testing at Bay Ridge include air infiltration reductions of greater than 60% in the DER building; a hybrid heat pump system with a Savings to Investment Ratio (SIR) > 1 (relative to a high efficiency furnace) which also provides the resident with added incentive for energy savings; and duct leakage reductions of > 60% using an aerosolized duct sealing approach. Despite being a moderate rehab instead of a gut rehab, the Bay Ridge DER is currently projected to achieve energy savings ≥ 50% compared to pre-retrofit, and the short-term testing supports this estimate.

  15. GridPix detectors: Production and beam test results

    Science.gov (United States)

    Koppert, W. J. C.; van Bakel, N.; Bilevych, Y.; Colas, P.; Desch, K.; Fransen, M.; van der Graaf, H.; Hartjes, F.; Hessey, N. P.; Kaminski, J.; Schmitz, J.; Schön, R.; Zappon, F.

    2013-12-01

    The innovative GridPix detector is a Time Projection Chamber (TPC) that is read out with a Timepix-1 pixel chip. By using wafer post-processing techniques an aluminium grid is placed on top of the chip. When operated, the electric field between the grid and the chip is sufficient to create electron induced avalanches which are detected by the pixels. The time-to-digital converter (TDC) records the drift time enabling the reconstruction of high precision 3D track segments. Recently GridPixes were produced on full wafer scale, to meet the demand for more reliable and cheaper devices in large quantities. In a recent beam test the contribution of both diffusion and time walk to the spatial and angular resolutions of a GridPix detector with a 1.2 mm drift gap are studied in detail. In addition long term tests show that in a significant fraction of the chips the protection layer successfully quenches discharges, preventing harm to the chip.

  16. Test results, Industrial Solar Technology parabolic trough solar collector

    Energy Technology Data Exchange (ETDEWEB)

    Dudley, V.E. [EG and G MSI, Albuquerque, NM (United States); Evans, L.R.; Matthews, C.W. [Sandia National Labs., Albuquerque, NM (United States)

    1995-11-01

    Sandia National Laboratories and Industrial Solar Technology are cost-sharing development of advanced parabolic trough technology. As part of this effort, several configurations of an IST solar collector were tested to determine the collector efficiency and thermal losses with black chrome and black nickel receiver selective coatings, combined with aluminized film and silver film reflectors, using standard Pyrex{reg_sign} and anti-reflective coated Pyrex{reg_sign} glass receiver envelopes. The development effort has been successful, producing an advanced collector with 77% optical efficiency, using silver-film reflectors, a black nickel receiver coating, and a solgel anti-reflective glass receiver envelope. For each receiver configuration, performance equations were empirically derived relating collector efficiency and thermal losses to the operating temperature. Finally, equations were derived showing collector performance as a function of input insolation value, incident angle, and operating temperature.

  17. Test results after refurbish of cryogenic system for smiles

    Science.gov (United States)

    Otsuka, Kiyomi; Tsunematsu, Shoji; Okabayashi, Akinobu; Narasaki, Katsuhiro; Satoh, Ryota

    2010-09-01

    Superconducting Sub-millimeter-wave Limb-Emission Sounder (SMILES) is to be operated aboard the Japanese Experiment Module (JEM) of the International Space Station (ISS) in 2009. SMILES uses two superconductor-insulator-superconductor (SIS) mixers for sub-millimeter-wave atmospheric observation and they are cooled to 4 K levels by a cryogenic system with a two-stage Stirling cooler, a Joule-Thomson (JT) cycle cooler and a cryostat composed of three stages. Two-stage Stirling cooler precools the JT circuit and also cools radiation shields in the cryostat. JT circuit has three tube-in-tube type heat exchangers and an orifice for JT expansion in the cryostat. The cryogenic system is built, tested and delivered.

  18. Flight test results for several light, canard-configured airplanes

    Science.gov (United States)

    Brown, Philip W.

    1987-01-01

    Brief flight evaluations of two different, light, composite constructed, canard and winglet configured airplanes were performed to assess their handling qualities; one airplane was a single engine, pusher design and the other a twin engine, push-pull configuration. An emphasis was placed on the slow speed/high angle of attack region for both airplanes and on the engine-out regime for the twin. Mission suitability assessment included cockpit and control layout, ground and airborne handling qualities, and turbulence response. Very limited performance data was taken. Stall/spin tests and the effects of laminar flow loss on performance and handling qualities were assessed on an extended range, single engine pusher design.

  19. Short-Term Test Results. Multifamily Home Energy Efficiency Retrofit

    Energy Technology Data Exchange (ETDEWEB)

    Lyons, James [Building America Partnership for Improved Residential Construction (BA-PIRC), Cocoa, FL (United States)

    2013-01-01

    Multifamily deep energy retrofits (DERs) represent great potential for energy savings, while also providing valuable insights on research-generated efficiency measures, cost-effectiveness metrics, and risk factor strategies for the multifamily housing industry. This report describes the Bay Ridge project, a base scope retrofit with a goal of achieving 30% savings (relative to pre-retrofit), and a DER scope with a goal of 50% savings (relative to pre-retrofit). Findings from the short-term testing at Bay Ridge include air infiltration reductions of greater than 60% in the DER building; a hybrid heat pump system with a Savings to Investment Ratio (SIR) > 1 (relative to a high efficiency furnace) which also provides the resident with added incentive for energy savings; and duct leakage reductions of > 60% using an aerosolized duct sealing approach.

  20. Filtration Understanding: FY10 Testing Results and Filtration Model Update

    Energy Technology Data Exchange (ETDEWEB)

    Daniel, Richard C.; Billing, Justin M.; Burns, Carolyn A.; Peterson, Reid A.; Russell, Renee L.; Schonewill, Philip P.; Shimskey, Rick W.

    2011-04-04

    This document completes the requirements of Milestone 2-4, Final Report of FY10 Testing, discussed in the scope of work outlined in the EM31 task plan WP-2.3.6-2010-1. The focus of task WP 2.3.6 is to improve the U.S. Department of Energy’s (DOE’s) understanding of filtration operations for high-level waste (HLW) to improve filtration and cleaning efficiencies, thereby increasing process throughput and reducing the Na demand (through acid neutralization). Developing the cleaning/backpulsing requirements will produce much more efficient operations for both the Hanford Tank Waste Treatment and Immobilization Plant (WTP) and the Savannah River Site (SRS), thereby significantly increasing throughput by limiting cleaning cycles. The scope of this work is to develop the understanding of filter fouling to allow developing this cleaning/backpulsing strategy.

  1. Helicopter vibration isolation: Design approach and test results

    Science.gov (United States)

    Lee, C.-M.; Goverdovskiy, V. N.; Sotenko, A. V.

    2016-03-01

    This paper presents a strategy based on the approach of designing and inserting into helicopter vibration isolation systems mountable mechanisms with springs of adjustable sign-changing stiffness for system stiffness control. A procedure to extend the effective area of stiffness control is presented; a set of parameters for sensitivity analysis and practical mechanism design is formulated. The validity and flexibility of the approach are illustrated by application to crewmen seat suspensions and vibration isolators for equipment protection containers. The strategy provides minimization of vibrations, especially in the infra-low frequency range which is the most important for crewmen efficiency and safety of the equipment. This also would prevent performance degradation of some operating systems. The effectiveness is demonstrated through measured data obtained from development and parallel flight tests of new and operating systems.

  2. Results of Laboratory Testing of Advanced Power Strips: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Earle, L.; Sparn, B.

    2012-08-01

    This paper describes the results of a laboratory investigation to evaluate the technical performance of advanced power strip (APS) devices when subjected to a range of home entertainment center and home office usage scenarios.

  3. STATISTICAL ANALYSIS OF SOME EXPERIMENTAL FATIGUE TESTS RESULTS

    OpenAIRE

    Adrian Stere PARIS; Gheorghe AMZA; Claudiu BABIŞ; Dan Niţoi

    2012-01-01

    The paper details the results of processing the fatigue data experiments to find the regression function. Application software for statistical processing like ANOVA and regression calculi are properly utilized, with emphasis on popular software like MSExcel and CurveExpert

  4. Resolve! Version 2.5: Flammable Gas Accident Analysis Tool Acceptance Test Plan and Test Results

    Energy Technology Data Exchange (ETDEWEB)

    LAVENDER, J.C.

    2000-10-17

    RESOLVE! Version 2 .5 is designed to quantify the risk and uncertainty of combustion accidents in double-shell tanks (DSTs) and single-shell tanks (SSTs). The purpose of the acceptance testing is to ensure that all of the options and features of the computer code run; to verify that the calculated results are consistent with each other; and to evaluate the effects of the changes to the parameter values on the frequency and consequence trends associated with flammable gas deflagrations or detonations.

  5. Beam Test Results for MSGC's with Thick Metal Strips.

    CERN Document Server

    Beaumont, W; Bernier, K; Bouhali, O; Boulogne, I; Daubie, Evelyne; De Troy, J G; Delentdecker, G; Devroede, O; Gregoire,,; Iacopi, F; Udo, Fred; Van Doninck, W K; Van Dyck, C; Van Lancker, L; Van der Velde, C; Verbeure, F; Zhukov, V

    1999-01-01

    Micro Strip Gas Counters with robust gold strips have been developed at IMEC, the Interuniversity Microelectronics Center at Leuven, in Belgium. The electroless plating technology was used, allowing to achieve a strip thickness of up to 1.6 mu m on 10 X 10 cm**2 substrates. Results on signal to noise ratio, spark rate, resulting damages and detector occupancy are presented for counters exposed to various intensities of heavily ionizing particles.

  6. Results of Edge Scatter Testing for a Starshade Mission

    Science.gov (United States)

    Smith, Daniel; Casement, L. Suzanne; Ellis, Scott; Stover, John; Warwick, Steve

    2017-01-01

    In the field of exoplanet detection and characterization, the use of a starshade, an external occulter in front of a telescope at large separations, has been identified as one of the highly promising methods to achieve the necessary high contrast imagery. Control of scattered sunlight from the edges of the starshade into the telescope has been identified as one of the key technology development areas in order to make the starshade feasible. Modeling of the scattered light has resulted in very different results so a campaign of experimentation with edge samples was undertaken to attempt to understand the discrepancies.Here, we present our results from the measurement of select samples of materials which would be suitable for manufacturing the starshade edge, and related models. We have focused on coating metallic samples for ease of fabrication: Titanium, Aluminum, and a Beryllium Copper alloy. Using standard machine shop methods, we fabricated samples which had sharp edges with radius of curvature (RoC) between 15 and 20 μm. We then had these samples coated by two suppliers to evaluate how well these coating types would conform to the edge and provide scatter suppression. The results of scatter measurements of these coated edge samples are presented. These scatter results have been incorporated into a new geometrical model in FRED which includes the details of the starshade mechanical model. This model predicts both the magnitude and distribution of the scattered sunlight in the image plane of a nominal telescope. We present these results, including a first effort at modeling the Solar System at 10 pc as seen by this mission architecture.

  7. Platform Precision Autopilot Overview and Flight Test Results

    Science.gov (United States)

    Lin, V.; Strovers, B.; Lee, J.; Beck, R.

    2008-01-01

    The Platform Precision Autopilot is an instrument landing system interfaced autopilot system, developed to enable an aircraft to repeatedly fly nearly the same trajectory hours, days, or weeks later. The Platform Precision Autopilot uses a novel design to interface with a NASA Gulfstream III jet by imitating the output of an instrument landing system approach. This technique minimizes, as much as possible, modifications to the baseline Gulfstream III jet and retains the safety features of the aircraft autopilot. The Platform Precision Autopilot requirement is to fly within a 5-m (16.4-ft) radius tube for distances to 200 km (108 nmi) in the presence of light turbulence for at least 90 percent of the time. This capability allows precise repeat-pass interferometry for the Uninhabited Aerial Vehicle Synthetic Aperture Radar program, whose primary objective is to develop a miniaturized, polarimetric, L-band synthetic aperture radar. Precise navigation is achieved using an accurate differential global positioning system developed by the Jet Propulsion Laboratory. Flight-testing has demonstrated the ability of the Platform Precision Autopilot to control the aircraft within the specified tolerance greater than 90 percent of the time in the presence of aircraft system noise and nonlinearities, constant pilot throttle adjustments, and light turbulence.

  8. NEW RESULTS FROM TESTING OF COPLANAR-GRID CDZNTE DETECTOR.

    Energy Technology Data Exchange (ETDEWEB)

    CARINI, G.A.; ET AL.

    2005-07-31

    New results from studies of coplanar-grid CdZnTe (CZT) detectors are presented. The coplanar-grid detectors, were investigated by using a highly collimated X-ray beam available at Brookhaven's National Synchrotron Light Source and by applying a pulse-shape analysis. The coplanar-grid detector operates as a single-carrier device. Despite the fact that its operational principle is well known and has been investigated by many groups in the past, we found some new details that may explain the performance limits of these types of devices. The experimental results have been confirmed by extensive computer modeling.

  9. STATISTICAL ANALYSIS OF SOME EXPERIMENTAL FATIGUE TESTS RESULTS

    Directory of Open Access Journals (Sweden)

    Adrian Stere PARIS

    2012-05-01

    Full Text Available The paper details the results of processing the fatigue data experiments to find the regression function. Application software for statistical processing like ANOVA and regression calculi are properly utilized, with emphasis on popular software like MSExcel and CurveExpert

  10. Up scaling and test results of an advanced Fresnel greenhouse

    NARCIS (Netherlands)

    Sonneveld, P.J.; Swinkels, G.L.A.M.; Tuijl, van B.A.J.; Janssen, H.J.J.; Zwart, de H.F.

    2012-01-01

    A greenhouse with Fresnel lenses in the south facing roof and a receiver for concentrated Photovoltaics with water cooling (CPVT system) will result in electrical and thermal energy output from the solar energy excess entering a greenhouse. The PV system converts about half of the direct radiation i

  11. Influence of test conditions and exposure duration on the result of ecotoxicological tests

    DEFF Research Database (Denmark)

    Rosenkrantz, Rikke Tjørnhøj

    Chemicals are used extensively and are part of many aspects of human life and society. They are useful and necessary for many purposes, but may also cause adverse effects on natural organisms if they are released to the environment during and after use. Therefore, it is necessary to perform a risk...... the temperature from 24 to 15°C caused a two-fold reduction in the toxicity of flupyrsulfuron-methyl, while no statistically significant changes was seen for metsulfuron-methyl, rimsulfuron, or thifensulfuron-methyl. Likewise, the introduction of a 12:12-hours light:dark cycle resulted in a two-fold reduction...... and possibly also modelling and it should consider the recovery of the organism The overall conclusion of this thesis is that under the current approach for derivation of EQS, there will be cases where basing the value on results from guideline tests alone will not be sufficiently protective of the environment...

  12. Advanced Rooftop Control (ARC) Retrofit: Field-Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Weimin; Katipamula, Srinivas; Ngo, Hung; Underhill, Ronald M.; Taasevigen, Danny J.; Lutes, Robert G.

    2013-07-31

    The multi-year research study was initiated to find solutions to improve packaged equipment operating efficiency in the field. Pacific Northwest National Laboratory (PNNL), with funding from the U.S. Department of Energy’s (DOE’s) Building Technologies Office (BTO) and Bonneville Power Administration (BPA) conducted this research, development and demonstration (RD&D) study. Packaged equipment with constant speed supply fans is designed to provide ventilation at the design rate at all times when the fan is operating as required by building code. Although there are a number of hours during the day when a building may not be fully occupied or the need for ventilation is lower than designed, the ventilation rate cannot be adjusted easily with a constant speed fan. Therefore, modulating the supply fan in conjunction with demand controlled ventilation (DCV) will not only reduce the coil energy but also reduce the fan energy. The objective of this multi-year research, development and demonstration project was to determine the magnitude of energy savings achievable by retrofitting existing packaged rooftop air conditioners with advanced control strategies not ordinarily used for packaged units. First, through detailed simulation analysis, it was shown that significant energy (between 24% and 35%) and cost savings (38%) from fan, cooling and heating energy consumption could be realized when packaged air conditioning units with gas furnaces are retrofitted with advanced control packages (combining multi-speed fan control, integrated economizer controls and DCV). The simulation analysis also showed significant savings for heat pumps (between 20% and 60%). The simulation analysis was followed by an extensive field test of a retrofittable advanced rooftop unit (RTU) controller.

  13. Results from tests of TFL Hydragard sampling loop

    Energy Technology Data Exchange (ETDEWEB)

    Steimke, J.L.

    1995-03-01

    When the Defense Waste Processing Facility (DWPF) is operational, processed radioactive sludge will be transferred in batches to the Slurry Mix Evaporator (SME), where glass frit will be added and the contents concentrated by boiling. Batches of the slurry mixture are transferred from the SME to the Melter Feed Tank (MFT). Hydragard{reg_sign} sampling systems are used on the SME and the MFT for collecting slurry samples in vials for chemical analysis. An accurate replica of the Hydragard sampling system was built and tested in the thermal Fluids Laboratory (TFL) to determine the hydragard accuracy. It was determined that the original Hydragard valve frequently drew a non-representative sample stream through the sample vial that ranged from frit enriched to frit depleted. The Hydragard valve was modified by moving the plunger and its seat backwards so that the outer surface of the plunger was flush with the inside diameter of the transfer line when the valve was open. The slurry flowing through the vial accurately represented the composition of the slurry in the reservoir for two types of slurries, different dilution factors, a range of transfer flows and a range of vial flows. It was then found that the 15 ml of slurry left in the vial when the Hydragard valve was closed, which is what will be analyzed at DWPF, had a lower ratio of frit to sludge as characterized by the lithium to iron ratio than the slurry flowing through it. The reason for these differences is not understood at this time but it is recommended that additional experimentation be performed with the TFL Hydragard loop to determine the cause.

  14. Tray Pack Improved Durability Packaging Rough Handling Test Results

    Science.gov (United States)

    1985-03-01

    extra vacuum void volume space makes these underfilled Tray Packs much more susceptible to damage. It is the vacuum that causes the damage not the under...filled to 6 lb. 10 oz. The result of underfilling is that the vacuum level in the peas is much higher making it more susceptible to paneling damage...impact. (3) That the vacuum induced by underfilling and vacuum pack- ing Tray Packs filled with peas makes them highly suscep- tible to damage. (4) That

  15. Boston Community Information System 1986 Experimental Test Results.

    Science.gov (United States)

    1987-08-01

    participants in the Boston CommnS. The questionnaire results showed a large interest in major corporations such as IBM, Digital Equipment, Data...DATA FROM THE FIS YEAR ’Computer, Electronic, Accounting’ - 1132 OIEEE Proceedings, Science, Communicatins of the ACM’ - 1137 ’American Political...higher if corporate . Since I moved it to the ofice to shape data with our [Oxfam Americal Press office and Ex. Dir. I have lez discretionary leisure

  16. Instrument Testing and First Results From the MOBB Observatory

    Science.gov (United States)

    Uhrhammer, R.; Romanowicz, B.; Neuhauser, D.; Stakes, D.; McGill, P.; Ramirez, T.

    2002-12-01

    The Monterey ocean bottom broadband station (MOBB) was installed on the sea floor in Monterey Bay, 40 km offshore, and at a depth of 1000m from the sea surface, in April 2002. It is a collaborative project between MBARI (Monterey Bay Aquarium Research Institute) and BSL (Berkeley Seismological Laboratory). The ocean-bottom MOBB station currently comprises a three-component seismometer package, a current-meter, and a recording and battery package. A differential pressure gauge (DPG) with autonomous recording (e.g. Cox et al., 1984) will be deployed in the vicinity of the seismometer package during the next data recovery dive, in September 2002. The seismic package contains a low-power (2.2W), three-component CMG-1T broadband seismometer system, built by Guralp, Inc., with a three-component 24-bit digitizer, a leveling system, and a precision clock. The seismometer package is mounted on a cylindrical titanium pressure vessel 54cm in height and 41 cm in diameter, custom built by the MBARI team and outfitted for underwater connection. Because of the extreme sensitivity of the seismometer, air movement within the pressure vessel must be minimized. We describe the extensive testing and insulation procedures performed at BSL. Among others, the top of the pressure vessel was thermally isolated with two inches of insulating foam and reflective Mylar. The sides were then insulated with multiple layers of reflective Mylar space blanket, and the vessel was filled with argon gas. The installation was completed during 3 dives (9-11 April, 2002), with the help of the MBARI ROV Ventana and ship Point Lobos. The site was revisited on April 22nd, to check the functioning of the system and 3Mb of data were then retrieved. The ship and ROV returned to the site two months later, on June 27th, and the data recording and battery modules were replaced, in the first of a series of such dives planned over the next 3 years. Many regional and teleseismic earthquakes have been well recorded

  17. Results of fracture mechanics tests on PNC SUS 304 plate

    Energy Technology Data Exchange (ETDEWEB)

    Mills, W.J.; James, L.A.; Blackburn, L.D.

    1985-08-01

    PNC provided SUS 304 plate to be irradiated in FFTF at about 400/sup 0/C to a target fluence of 5 x 10/sup 21/ n/cm/sup 2/ (E > 0.1 MeV). The actual irradiation included two basically different exposure levels to assure that information would be available for the exposure of interest. After irradiation, tensile properties, fatigue-crack growth rates and J-integral fracture toughness response were determined. These same properties were also measured for the unirradiated material so radiation damage effects could be characterized. This report presents the results of this program. It is expected that these results would be applicable for detailed fracture analysis of reactor components. Recent advances in elastic-plastic fracture mechanics enable reasonably accurate predictions of failure conditions for flawed stainless steel components. Extensive research has focused on the development of J-integral-based engineering approach for assessing the load carrying capacity of low-strength, high-toughness structural materials. Furthermore, Kanninen, et al., have demonstrated that J-integral concepts can accurately predict the fracture response for full-scale cracked structures manufactured from Type 304 stainless steel.

  18. Pressurization test results: Bonneville Power Administration Energy Conservation Study

    Energy Technology Data Exchange (ETDEWEB)

    Krinkel, D.L.; Dickeroff, D.J.; Casey, J.; Grimsrud, D.T.

    1980-12-01

    Results are presented of air leakage measurements in 18 single-family detached houses at the Midway substation, Hanford, Washington, performed as part of the Bonneville Power Administration's Energy Conservation Study. The change in energy consumption following various retrofit strategies is compared. Air leakage was measured in each house with the fan pressurization technique, before and after the retrofits were installed. No significant change was found in infiltration rates in those houses receiving either no retrofits or insulation only; and average reduction of 17% in leakage area was found in the houses retrofitted with storm doors and windows. There appears to be great potential for further savings in energy use from reduced infiltration, and the study is being extended to investigate this.

  19. Initial Test Results from a 3-axis Vibrating Ring Gyroscope

    Energy Technology Data Exchange (ETDEWEB)

    Gallacher, B J; Neasham, J A; Burdess, J S; Harris, A J [INSAT University of Newcastle upon Tyne NE1 7RU (United Kingdom)

    2006-04-01

    There are several application areas where the simultaneous measurement of rates of rotation about three mutually orthogonal axes is required. In this paper the principle features of a 3-axis vibrating ring gyroscope are described. The fabrication process for the gyroscope is presented and employs standard MEMS techniques. The modal properties for the ring are measured experimentally using laser vibrometry and electrostatic sensing and compared with the design predictions. In operation as a rate gyroscope it is necessary to excite the primary motion of the gyroscope and control is amplitude. As Q-factors of vibratory gyroscope are typically of the order 10{sup 3}-10{sup 4} slight variations in environmental conditions will perturb the natural frequency of the primary mode significantly. To ensure the primary motion of the gyroscope is maintained with constant amplitude a control scheme employing both frequency tracking and amplitude control is required. An electronic control system using digital signal processing (DSP) has been developed to ensure excitation of the primary motion occurs at resonance with controlled amplitude. The control scheme employs an embedded processor to generate the drive frequency (via a D/A converter) and to monitor the primary vibration (via an A/D converter). Experimental results from the control scheme highlighting its effectiveness over conventional PLL approaches are presented.

  20. Central location test vs. home use test: Contrasting results depending on product type

    NARCIS (Netherlands)

    Boutrolle, I.; Delarue, J.; Arranz, D.; Rogeaux, M.; Köster, E.P.

    2007-01-01

    Marketing professionals and sensory scientists have several hedonic testing methods at their disposal to assess product acceptability. The central location test (CLT) which usually takes place in a standardised location under controlled conditions is more frequently used than the home use test (HUT)

  1. Evaluation of LLTR Series II test A-2 results. [Large Leak Test Rig

    Energy Technology Data Exchange (ETDEWEB)

    Whipple, J C; Shoopak, B F; Chen, K; Fan, C K; Odegaard, T K

    1980-07-01

    Series II Test A-2 employed a double-ended (DEG) tube rupture 122'' above the lower end of the LLTI shroud under typical evaporator startup conditions. The leak site was located 2'' below Spacer No. 4 at the same location as Test A-lb which employed nitrogen as the inert non-reactive injection fluid. The test yielded peak pressures of 375 psig in the leak site region and 485 psig at the upper tubesheet approximately 10 ms and 12 ms, respectively, after tube rupture. Higher peak temperatures (approx. 2200/sup 0/F) were measured in this test than during Series I sodium-water reaction testing (peak temperatures measured during Series were about 1900/sup 0/F maximum). These high peak temperatures occurred in Test A-2 long after the tube rupture (approx. 8 seconds) and did not contribute to the acoustic peak pressures produced in the first few milliseconds.

  2. Description of buffer tests in 2005 - 2007. Results of laboratory tests

    Energy Technology Data Exchange (ETDEWEB)

    Sanden, Torbjoern; Boergesson, Lennart; Dueck, Ann; Goudarzi, Reza; Loennqvist, Margareta; Nilsson, Ulf; Aakesson, Mattias (Clay Technology AB, Lund (Sweden))

    2008-12-15

    The horizontal design for the deposition of nuclear waste in granitic rock has been ongoing since 2002. Clay Technology has contributed with studies that mainly concern the behaviour and design of the bentonite buffer material. The work described in this report was a part of the design subproject and was conducted from 2005 up to mid-2007. The results of the work and the increased general understanding of the behaviour of the buffer in KBS-3H have led to two main designs. BD (Basic Design) and DAWE (Drainage Artificial Watering and air Evacuation). Several significant uncertainties related to the behaviour of distance blocks and buffer materials were identified. The most important issues to be resolved were included in an extensive buffer test plan and this report presents the work carried. The critical issues (an issue is defined as critical if there is clear uncertainty in fulfilling the design basis) to be resolved to produce viable designs were: 1. Humidity-induced swelling. This process may cause cracking and subsequent loss of bentonite as the debris falls on to the floor. There is also the possibility that the blocks could swell and come into contact with the rock wall. Both these processes will lead to a hindering of the free water flow on the tunnel floor in DAWE and may subsequently result in the erosion of bentonite material from the tunnel. This is not expected to be an issue in the BD owing to the small buffer-rock gap engineered into the design. 2. Erosion of of filling blocks and buffer. This process will lead either to a loss of material from the emplacement drift if it takes place before a hydraulic plug is built or to redistribution of bentonite in the emplacement drift if it takes place afterwards. Localized erosion may be harmful for both design alternatives if it results in a substantial loss or redistribution of material. 3. Artificial wetting of distance blocks. Both design alternatives include artificial water filling of the gap between the

  3. Test and Evaluation (T&E)

    Science.gov (United States)

    2013-03-04

    TERMS 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT Same as Report ( SAR ) 18. NUMBER OF PAGES 28 19a. NAME OF RESPONSIBLE PERSON a...412 TW Edwards AFB Bistatic Radar Cross-Section Benefield Anechoic Chamber test PI Tony Quach AFRL/RY TCTTA Ed Utt 96 TW Eglin AFB High Power

  4. Psychological distress with direct-to-consumer genetic testing: a case report of an unexpected BRCA positive test result.

    Science.gov (United States)

    Dohany, Lindsay; Gustafson, Shanna; Ducaine, Whitney; Zakalik, Dana

    2012-06-01

    We report a case of a client who discovered she had a BRCA mutation following direct-to-consumer (DTC) genetic testing in the absence of genetic counseling. After testing she presented for genetic counseling with anxiety, distress, and a deficit of knowledge about what the DTC genetic testing revealed. Genetic counseling helped alleviate distress while empowering the client to apply the results of testing to improve medical management. Despite recent studies demonstrating no negative psychological impact of DTC genetic testing on the consumer, this case illustrates that significant psychological distress and confusion can occur as a result of DTC genetic testing for highly penetrant single gene disorders. Pre- and post-test genetic counseling in conjunction with DTC genetic testing may alleviate consumers' distress and empower clients to proactively utilize their result information.

  5. Reading Results: A Critical Look at Standardized Testing and the Linguistic Minority

    Science.gov (United States)

    Shannon, Joanie

    2008-01-01

    A critical look into assessing the Standardized Test and Reporting (STAR) test data among English language learners gives educators a chance to examine the cultural biases present within the standardized test movement started by the No Child Left Behind Act of 2001. In particular, The STAR test results seem to reflect that the test is geared…

  6. Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Judkoff, R.; Polly, B.; Bianchi, M.; Neymark, J.; Kennedy, M.

    2011-08-01

    This publication summarizes building energy simulation test for existing homes (BESTEST-EX): instructions for implementing the test procedure, calibration tests reference results, and example acceptance-range criteria.

  7. The Cultural Politics of National Testing and Test Result Release Policy in South Korea: A Critical Discourse Analysis

    Science.gov (United States)

    Sung, Youl-Kwan; Kang, Mi Ok

    2012-01-01

    This paper examines the ideological construction of educational discourses embedded within the South Korean print media. Significantly, these discourses have recently promoted the resurrection of a sweeping national testing and test results release policy. Through careful examination of the "test plus release" policy, the authors show…

  8. Field Lysimeter Test Facility: Protective barrier test results (FY 1990, the third year)

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, M.D.; Gee, G.W.

    1990-11-01

    The Field Lysimeter Test Facility (FLTF) was constructed to test protective barriers for isolating low-level radioactive and hazardous wastes from the biosphere. Protective barriers are specially configured earth materials placed over near-surface wastes to prevent intrusion of water, plants, and animals. Low-level radioactive waste is stored in near-surface repositories at the Hanford Site and can be transported into the biosphere by water, plants, and animals. The purpose of the FLTF is to measure water balance within barriers as precipitation is partitioned to evaporation (including transpiration), storage, and drainage. Runoff was prevented by raised edges on the lysimeters. Water balance in protective barriers depends on the water-holding capacity of the soil, the gradient of a potential, and the conductivity of the underlying capillary barrier. Current barrier design uses soil with a high water storage capacity and a capillary barrier underlying the soil to increase its water storage capacity. This increased storage capacity is to hold water, which would normally drain, near the the surface where evaporation can cycle it back to the atmosphere. 7 refs., 23 figs., 5 tabs.

  9. Evaluation of Reflections in a MIMO OTA Test Setup

    DEFF Research Database (Denmark)

    Barrio, Samantha Caporal Del; Franek, Ondrej; Krenz, Gunter

    2014-01-01

    With the commercialization of MIMO devices, accurate over-the-air testing has become a major research area in mobile communications. Several test methods are investigated in the related work. This paper discusses the anechoic chamber method and specifically deals with reflections between probes...

  10. A Study of the Anechoic Performance of Rice Husk-Based, Geometrically Tapered, Hollow Absorbers

    Directory of Open Access Journals (Sweden)

    Muhammad Nadeem Iqbal

    2014-01-01

    Full Text Available Although solid, geometrically tapered microwave absorbers are preferred due to their better performance, they are bulky and must have a thickness on the order of λ or more. The goal of this study was to design lightweight absorbers that can reduce the electromagnetic reflections to less than −10 dB. We used a very simple approach; two waste materials, that is, rice husks and tire dust in powder form, were used to fabricate two independent samples. We measured and used their dielectric properties to determine and compare the propagation constants and quarter-wave thickness. The quarter-wave thickness for the tire dust was 3 mm less than that of the rice husk material, but we preferred the rice-husk material. This preference was based on the fact that our goal was to achieve minimum backward reflections, and the rice-husk material, with its low dielectric constant, high loss factor, large attenuation per unit length, and ease of fabrication, provided a better opportunity to achieve that goal. The performance of the absorbers was found to be better (lower than −20 dB, and comparison of the results proved that the hollow design with 58% less weight was a good alternative to the use of solid absorbers.

  11. Test Results From The Idaho National Laboratory 15kW High Temperature Electrolysis Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Carl M. Stoots; Keith G. Condie; James E. O' Brien; J. Stephen Herring; Joseph J. Hartvigsen

    2009-07-01

    A 15kW high temperature electrolysis test facility has been developed at the Idaho National Laboratory under the United States Department of Energy Nuclear Hydrogen Initiative. This facility is intended to study the technology readiness of using high temperature solid oxide cells for large scale nuclear powered hydrogen production. It is designed to address larger-scale issues such as thermal management (feed-stock heating, high temperature gas handling, heat recuperation), multiple-stack hot zone design, multiple-stack electrical configurations, etc. Heat recuperation and hydrogen recycle are incorporated into the design. The facility was operated for 1080 hours and successfully demonstrated the largest scale high temperature solid-oxide-based production of hydrogen to date.

  12. How do people respond to self-test results? A cross-sectional survey

    Directory of Open Access Journals (Sweden)

    de Vries Nanne K

    2010-10-01

    Full Text Available Abstract Background Self-tests, tests on medical conditions that can be performed by consumers without consulting a doctor first, are frequently used. Nevertheless, there are concerns about the safety of self-testing, as it may delay diagnosis and appropriate treatment in the case of inappropriate use of the test, or false-negative results. It is unclear whether self-tests stimulate appropriate follow-up behaviour. Our aim was to examine the frequency of self-test use, consumers' response to self-test results in terms of their confidence in the result, reassurance by the test result, and follow-up behaviour. Methods A two step cross-sectional survey was designed. A random sample of 6700 Internet users in an existing Internet panel received an online questionnaire on the use of self-tests. Self-tests were defined as tests on body materials, initiated by consumers with the aim to diagnose a disease or risk factor. A second questionnaire on consumers' response to self-test results was sent to the respondents that were identified as a self-tester in the first questionnaire (n = 703. Results 18.1% (799/4416 of the respondents had ever performed a self-test, the most frequently used tests being those for diabetes (5.3%, kidney disease (4.9%, cholesterol (4.5%, urinary tract infection (1.9% and HIV/AIDS and Chlamydia (both 1.6%. A total of 78.1% of the testers with a normal test result and 81.4% of those with an abnormal result reported confidence in this result. Almost all (95.6% of the testers with a normal result felt reassured. After a normal result, 78.1% did not take any further action and 5.8% consulted a doctor. The corresponding figures after an abnormal test result were 9.3% and 72.2%, respectively. Conclusions Respondents who had performed a self-test seemed to base their follow-up behaviour on the result of the test. They had confidence in the test result, and were often reassured by a normal result. After an abnormal result, most self

  13. PHYSICS RESULTS OF THE NSLS-II LINAC FRONT END TEST STAND

    Energy Technology Data Exchange (ETDEWEB)

    Fliller R. P.; Gao, F.; Yang, X.; Rose, J.; Shaftan, T.; Piel, C

    2012-05-20

    The Linac Front End Test Stand (LFETS) was installed at the Source Development Laboratory (SDL) in the fall of 2011 in order to test the Linac Front End. The goal of these tests was to test the electron source against the specifications of the linac. In this report, we discuss the results of these measurements and the effect on linac performance.

  14. Results from Second Round of Remediated Nitrate Salt Surrogate Formulation and Testing

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Geoffrey Wayne [Los Alamos National Laboratory; Leonard, Philip [Los Alamos National Laboratory; Hartline, Ernest Leon [Los Alamos National Laboratory; Tian, Hongzhao [Los Alamos National Laboratory

    2016-04-04

    High Explosives and Technology (M-7) completed the second round of formulation and testing of Remediated Nitrate Salt (RNS) surrogates on March 17, 2016. This report summarizes the results of the work and also includes additional documentation required under test plan PLAN-TA9-2443 Rev B, "Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing Standard Procedure", released February 16, 2016. All formulation and testing was carried out according to PLAN-TA9-2443 Rev B. Results from the first round of formulation and testing were documented in memorandum M7-16-6042, "Results from First Round of Remediated Nitrate Salt Surrogate Formulation and Testing."

  15. Analyzing VLSI component test results of a GenRad GR125 tester

    Science.gov (United States)

    Zulaica, D.; Lee, C.-H.

    1995-06-01

    The GenRad GR125 VLSI chip tester provides tools for testing the functionality of entire chips. Test operation results, such as timing sensitivity or propagation delay, can be compared to published values of other manufacturers' chips. The tool options allow for many input vector situations to be tested, leaving the possibility that a certain test result has no meaning. Thus, the test operations are also analyzed for intent. Automating the analysis of test results can speed up the testing process and prepare results for processing by other tools. The procedure used GR125 test results of a 7404 Hex Inverter in a sample VHDL performance modeler on a Unix workstation. The VHDL code is simulated using the Mentor Graphics Corporation's Idea Station software, but should be portable to any VHDL simulator.

  16. Setup, tests and results for the ATLAS TileCal Read Out Driver production

    CERN Document Server

    Valero, Alberto; Castillo, V; Cuenca, C; Ferrer, A; Fullana, E; González, V; Higón, E; Munar, A; Poveda, J; Ruiz-Martínez, A; Salvachúa, B; Sanchís, E; Solans, C; Soret, J; Torres, J; Valls, J A

    2007-01-01

    In this paper we describe the performance and test results of the production of the 38 ATLAS TileCal Read Out Drivers (RODs). We first describe the basic hardware specifications and firmware functionality of the modules, the test-bench setup used for production and the test procedure to qualify the boards. We then finally show and discuss the performance results.

  17. Conductor and joint test results of JT-60SA CS and EF coils using the NIFS test facility

    Science.gov (United States)

    Obana, Tetsuhiro; Takahata, Kazuya; Hamaguchi, Shinji; Kizu, Kaname; Murakami, Haruyuki; Chikaraishi, Hirotaka; Noguchi, Hiroki; Kobuchi, Takashi; Moriuchi, Sadatomo; Imagawa, Shinsaku; Mito, Toshiyuki; Tsuchiya, Katsuhiko; Natsume, Kyohei; Yoshida, Kiyoshi; Nomoto, Kazuhiro; Kim, Tae-hyun

    2016-01-01

    In 2007, JAEA and NIFS launched the test project to evaluate the performance of cable-in-conduit (CIC) conductors and conductor joints for the JT-60SA CS and EF coils. In this project, conductor tests for four types of coil conductor and joint tests for seven types of conductor joint have been conducted for the past eight years using the NIFS test facility. As a result, the test project indicated that the CIC conductors and conductor joints fulfill the design requirement for the CS and EF coils. In addition, the NIFS test facility is expected to be utilized as the test facility for the development of a conductor and conductor joint for the purpose of the DEMO nuclear fusion power plant, provided that the required magnetic field strength is within 9 T.

  18. Discussion on Low Frequency Response Loss of Loudspeaker Box in Anechoic Chamber%谈谈音箱在消声室测量中低频响应的缺失

    Institute of Scientific and Technical Information of China (English)

    徐柏龄

    2015-01-01

    When the frequency response of the loudspeaker box is measured in the anechoic chamber, the low frequency response is often lost, which often happens when the position of the speaker box is not in the free field of the anechoic chamber. This paper also points out several key points which should be paid attention to when the frequency response of the loudspeaker box is measured in the anechoic chamber.%在消声室中测量音箱的频响曲线时,往往会造成低频响应的丢失,这通常是由于被测音箱的位置不在消声室的自由声场而引起的。本文指出了在消声室中测量音箱的频响时必须注意的几个问题。

  19. Lay perceptions of predictive testing for diabetes based on DNA test results versus family history assessment: a focus group study

    Directory of Open Access Journals (Sweden)

    Cornel Martina C

    2011-07-01

    Full Text Available Abstract Background This study assessed lay perceptions of issues related to predictive genetic testing for multifactorial diseases. These perceived issues may differ from the "classic" issues, e.g. autonomy, discrimination, and psychological harm that are considered important in predictive testing for monogenic disorders. In this study, type 2 diabetes was used as an example, and perceptions with regard to predictive testing based on DNA test results and family history assessment were compared. Methods Eight focus group interviews were held with 45 individuals aged 35-70 years with (n = 3 and without (n = 1 a family history of diabetes, mixed groups of these two (n = 2, and diabetes patients (n = 2. All interviews were transcribed and analysed using Atlas-ti. Results Most participants believed in the ability of a predictive test to identify people at risk for diabetes and to motivate preventive behaviour. Different reasons underlying motivation were considered when comparing DNA test results and a family history risk assessment. A perceived drawback of DNA testing was that diabetes was considered not severe enough for this type of risk assessment. In addition, diabetes family history assessment was not considered useful by some participants, since there are also other risk factors involved, not everyone has a diabetes family history or knows their family history, and it might have a negative influence on family relations. Respect for autonomy of individuals was emphasized more with regard to DNA testing than family history assessment. Other issues such as psychological harm, discrimination, and privacy were only briefly mentioned for both tests. Conclusion The results suggest that most participants believe a predictive genetic test could be used in the prevention of multifactorial disorders, such as diabetes, but indicate points to consider before both these tests are applied. These considerations differ with regard to the method of assessment

  20. TID Test Results for 4th Generation iPad(TradeMark)

    Science.gov (United States)

    Guertin, S. M.; Allen, G. R.; McClure, S. S.; LaBel, K. A.

    2013-01-01

    TID testing of 4th generation iPads is reported. Of iPad subsystems, results indicate that the charging circuitry and display drivers fail at lowest TID levels. Details of construction are investigated for additional testing of components.

  1. Ground vibration test results for Drones for Aerodynamic and Structural Testing (DAST)/Aeroelastic Research Wing (ARW-1R) aircraft

    Science.gov (United States)

    Cox, T. H.; Gilyard, G. B.

    1986-01-01

    The drones for aerodynamic and structural testing (DAST) project was designed to control flutter actively at high subsonic speeds. Accurate knowledge of the structural model was critical for the successful design of the control system. A ground vibration test was conducted on the DAST vehicle to determine the structural model characteristics. This report presents and discusses the vibration and test equipment, the test setup and procedures, and the antisymmetric and symmetric mode shape results. The modal characteristics were subsequently used to update the structural model employed in the control law design process.

  2. Is the psychological impact of genetic testing moderated by support and sharing of test results to family and friends?

    Science.gov (United States)

    Lapointe, Julie; Dorval, Michel; Noguès, Catherine; Fabre, Roxane; Julian-Reynier, Claire

    2013-12-01

    Receiving the results of genetic tests for a breast and ovarian cancer susceptibility can be a stressful experience. Here we studied the effects of social support (SS) and the sharing of test results on the psychological impact of BRCA1/2 test result disclosure. We also compared carriers and non-carriers on sharing, SS and psychological impact. Five-hundred and twenty-two unaffected women were followed prospectively for 2 years after receiving their test results. Psychological impact was measured on the impact of event scale. Multivariate multi-level models were used, and all the analyses were stratified depending on mutation status (carriers vs non-carriers). Two weeks after receiving their BRCA1/2 results, carriers had shared their test results less frequently than non-carriers (p test results was not significantly associated with psychological impact. Availability of SS was significantly associated with better psychological adjustment across time among carriers (p < 0.01), but not among non-carriers. For female BRCA1/2 mutation carriers, the importance of SS should be stressed, and possible ways of enlisting people in their entourage for this purpose should be discussed in the context of clinical encounters.

  3. The Estimation of Knowledge Solidity Based on the Comparative Analysis of Different Test Results

    Directory of Open Access Journals (Sweden)

    Y. K. Khenner

    2012-01-01

    Full Text Available At present, the testing techniques of knowledge estimation are widely spread in educational system. However, this method is seriously criticized including its application to the Unified State Examinations. The research is aimed at studying the limitations of testing techniques. The authors recommend a new way of knowledge solid- ity estimation bases on the comparative results analysis of various kinds of tests. While testing the large group of students, the authors found out that the results of the closed and open tests substantially differ. The comparative analysis demonstrates that the open tests assessment of the knowledge solidity is more adequate than that of the closed ones. As the research is only based on a single experiment, the authors recommend using this method further, substantiating the findings concerning the differences in tests results, and analyzing the advantages and disadvantages of the tests in question. 

  4. Spatial patterns in discordant diagnostic test results for Chagas disease: links to transmission hotspots.

    Science.gov (United States)

    Levy, Michael Z; Bowman, Natalie M; Kawai, Vivian; Plotkin, Joshua B; Waller, Lance A; Cabrera, Lilia; Steurer, Frank; Seitz, Amy E; Pinedo-Cancino, Viviana V; Cornejo del Carpio, Juan Geny; Cordova Benzaquen, Eleazar; McKenzie, F Ellis; Maguire, James H; Gilman, Robert H; Bern, Caryn

    2009-04-15

    Diagnosis of Chagas disease is hindered by discordance between screening and confirmatory test results for Trypanosoma cruzi infection. In periurban Arequipa, Peru, spatial analysis revealed that individuals with discordant test results are spatially clustered in hotspots of T. cruzi transmission, suggesting that discordant results likely represent true infections in this setting.

  5. Results of Shipboard Approval Tests of Ballast Water Treatment Systems in Freshwater

    Science.gov (United States)

    2014-11-01

    Results of Shipboard Approval Tests of Ballast Water Treatment Systems in Freshwater Distribution Statement A: Approved for public release...distribution is unlimited. November 2014 Report No. CG-D-05-15 Results of Shipboard Approval Tests of BWT Systems in Freshwater ii...London, CT 06320 Results of Shipboard Approval Tests of BWT Systems in Freshwater iii UNCLAS//Public | CG-926 R&DC | Cangelosi, et al

  6. Field Lysimeter Investigations - test results: Low-Level Waste Data Base Development Program: Test results for fiscal years 1994-1995

    Energy Technology Data Exchange (ETDEWEB)

    McConnell, J.W. Jr.; Rodgers, R.D.; Hilton, L.D.; Neilson, R.M. Jr. [and others

    1996-06-01

    The Field Lysimeter Investigations: Low-Level Waste Data Base Development Program, funded by the U.S. Nuclear Regulatory Commission (NRC), is (1) studying the degradation effects in EPICOR-II organic ion-exchange resins caused by radiation, (2) examining the adequacy of test procedures recommended in the Branch Technical Position on Waste Form to meet the requirements of 10 CFR 61 using solidified EPICOR-II resins, (3) obtaining performance information on solidified EPICOR-II ion-exchange resins in a disposal environment, and (4) determining the condition of EPICOR-II liners. Results of the final 2 (10 total) years of data acquisition from operation of the field testing are presented and discussed. During the continuing field testing, both portland type I-II cement and Dow vinyl ester-styrene waste forms are being tested in lysimeter arrays located at Argonne National Laboratory-East in Illinois and at Oak Ridge National Laboratory. The experimental equipment is described and results of waste form characterization using tests recommended by the NRC`s {open_quotes}Technical Position on Waste Form{close_quotes} are presented. The study is designed to provide continuous data on nuclide release and movement, as well as environmental conditions, over a 20-year period. At the end of the tenth year, the experiment was closed down. Examination of soil and waste forms is planned to be conducted next and will be reported later.

  7. Multipacting simulation and test results of BNL 704 MHz SRF gun

    Energy Technology Data Exchange (ETDEWEB)

    Xu W.; Belomestnykh, S.; Ben-Zvi, I.; Cullen, C. et al

    2012-05-20

    The BNL 704MHz SRF gun has a grooved choke joint to support the photo-cathode. Due to the distortion of grooves at the choke joint during the BCP for the choke joint, several multipacting barriers showed up when it was tested with Nb cathode stalk at JLab. We built a setup to use the spare large grain SRF cavity to test and condition the multipacting at BNL with various power sources up to 50kW. The test is carried out in three stages: testing the cavity performance without cathode, testing the cavity with the Nb cathode stalk that was used at Jlab, and testing the cavity with a copper cathode stalk that is based on the design for the SRF gun. This paper summarizes the results of multipacting simulation, and presents the large grain cavity test setup and the test results.

  8. ExoMars 2016 EDM SM Mechanical Test Campaign Engineering Results Evaluation

    Science.gov (United States)

    Luison, Dario; Tenore, Amedeo Giancarlo

    2014-06-01

    This paper describes the analytical engineering activities done in the frame of ExoMars Descent Module (EDM) Structural Model (SM) Mechanical Test Campaign performed in ESTEC (for Sinusoidal Test) and in Thales Alenia Space Turin (Italy) laboratories (for Static Test) in the period from February and July 2013.The main results of Sine and Static Tests are described, as well as the updating of the Mathematical Model based on the results of the Base Excitation Vibration Modal Parameters Extraction. The engineering test evaluation activity was concentrated in particular on the simulation of the failure occurred during the sine test. This failure represented a serious issues never encountered in previous tests. Despite the gravity of the phenomenon, in a short time, the engineering was able to prove the structural integrity and to conclude successfully the test.

  9. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Gary Blythe

    2007-05-01

    Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests were completed in 2005 and have been previously reported. This topical report presents the results from the Task 3 full-scale additive tests, conducted at IPL's Petersburg Station Unit 2. The Task 5 full-scale additive tests will be conducted later in calendar year 2007.

  10. Ares I Scale Model Acoustic Test Above Deck Water Sound Suppression Results

    Science.gov (United States)

    Counter, Douglas D.; Houston, Janice D.

    2011-01-01

    The Ares I Scale Model Acoustic Test (ASMAT) program test matrix was designed to determine the acoustic reduction for the Liftoff acoustics (LOA) environment with an above deck water sound suppression system. The scale model test can be used to quantify the effectiveness of the water suppression system as well as optimize the systems necessary for the LOA noise reduction. Several water flow rates were tested to determine which rate provides the greatest acoustic reductions. Preliminary results are presented.

  11. Almagate interference in breath test results for the diagnosis of Helicobacter pylori infection

    Directory of Open Access Journals (Sweden)

    Carles Pons

    2014-08-01

    Full Text Available Background: Infection by Helicobacter pylori is common and affects both genders at any age. The 13C-urea breath test is a widely used test for the diagnosis of this infection. However, multiple drugs used for the treatment of Helicobacter pylori infection symptoms have interactions with this breath test that generate false negative results. This observational study was to assess the potential interaction between almagate and the breath test. Methods: Thirty subjects on almagate therapy who underwent a breath test were included. If the result was negative, almagate was withdrawn for a month and the breath test was then repeated. Results: In general, 51.9 % of assessed subjects had a negative result after the first test, and 100 % of these also had a negative result after the second test. Conclusions: It was concluded that the use of almagate does not interfere in breath test results. These results provide a drug therapy option for the treatment of symptoms associated with Helicobacter pylori infection during the diagnostic process.

  12. Characteristics of genomic test consumers who spontaneously share results with their health care provider.

    Science.gov (United States)

    Darst, Burcu F; Madlensky, Lisa; Schork, Nicholas J; Topol, Eric J; Bloss, Cinnamon S

    2014-01-01

    The purpose of this study was to evaluate the characteristics of direct-to-consumer (DTC) genomic test consumers who spontaneously shared their test results with their health care provider. Utilizing data from the Scripps Genomic Health Initiative, we compared demographic, behavioral, and attitudinal characteristics of DTC genomic test consumers who shared their results with their physician or health care provider versus those who did not share. We also compared genomic risk estimates between the two groups. Of 2,024 individuals assessed at approximately 6 months post testing, 540 individuals (26.5%) reported sharing their results with their physician or health care provider. Those who shared were older (p consumers.

  13. 基于VISA和Mint的微波暗室自动测量系统实现%Implemenation of the Microwave Anechoic Chamber Automatic Measuring System Based on VISA and Mint

    Institute of Scientific and Technical Information of China (English)

    李瑞阳; 韦高; 韩旭; 符礼

    2013-01-01

    建立了一套基于VISA和Mint的微波暗室自动测量系统,通过计算机控制矢网和转台以实现高效率的天线与RCS的微波暗室自动测量.在Visual C++开发环境下,运用多线程技术将矢网和转台结合,同时采用VISA和SCPI命令实现矢网的自动控制,采用Mint ActiveX控件技术实现转台的自动控制,该方法易于实现矢网与转台的高效同步.实测表明,该系统操作方便,测量效率、测量精度与自动化程度较高,所采用的控制方法有着较好的通用性和可拓展性,具有广阔的应用前景.%In order to realize efficient automatic antenna and RCS measurement,a microwave anechoic chamber automatic measurement system has been established,using the computer to control the vector network analyzer and the test turntable.In visual C++development environment,the multithread technology is used to combine the vector network analyzer with the test turntable.The vector network analyzer is auto-controlled by VISA and SCPI command ; the test turntable is auto-controlled by Mint ActiveX control technology.The methods are easy to efficiently synchronize the two devices.The actual measurement shows that the system is easy to control,and has high measurement efficiency,high precision,and high automaticity.The controlling method has broad application prospects for it has good universality and is easy to expand.

  14. Results and comparison of seven accelerated cycling test procedures for the photovoltaic application

    Science.gov (United States)

    Potteau, E.; Desmettre, D.; Mattera, F.; Bach, O.; Martin, J.-L.; Malbranche, P.

    Choosing the right battery for a given photovoltaic (PV) system is a key question, because it strongly influences the cost and reliability of the system. This paper presents results of seven test procedures experienced at the GENEC battery test facility. A set of four complementary tests is selected, covering the various types of photovoltaic systems. Moreover, the analysis of these results gives an estimation of the ageing rate for the different types of batteries used in photovoltaic systems.

  15. Official list of results of fuel-consumption tests on passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    This booklet contains the results of the officially approved fuel consumption tests recorded by the Department of Transport to late March 1981 and gives car buyers comparative information about the fuel economy of different models achieved in standard tests. The official tests have been designed to be representative of real-life driving situations and the results achieved provide a guide to the models which are likely to be more economical in their fuel use.

  16. 75 FR 32484 - Array-Based Cytogenetic Tests: Questions on Performance Evaluation, Result Reporting and...

    Science.gov (United States)

    2010-06-08

    ... Performance Evaluation, Result Reporting and Interpretation. The purpose of the public meeting is to seek input on challenges related to performance evaluation, determination of clinical significance, result... HUMAN SERVICES Food and Drug Administration Array-Based Cytogenetic Tests: Questions on...

  17. False Positive Results of Carpal tunnel syndrome in Electro Diagnosis Tests

    Directory of Open Access Journals (Sweden)

    MR Emad

    2010-07-01

    Full Text Available Introduction & Objective: Carpal tunnel syndrome is identified due to compression of median nerve at wrist and develops symptoms such as wrist pain, paresthesia, numbness and the dysfunction of the hands. The gold standard to diagnose, determining prognosis and planning treatment process based on the severity of nerve involvement are electro-diagnosis tests. The purpose of this study was to specify the least and the most false positive results in common electro-diagnosis tests. Materials & Methods: This descriptive study was conducted at Shiraz University of Medical Sciences in 2009. Twelve different electro-diagnosis tests on fifty-five normal cases (110 available hands, which never had experienced the symptoms of this syndrome, were carried out. The data was statistically analyzed by SPSS software, using T test and Cochran's `Q. Results: There were false positive results in many of the performed tests. The most false-positive result was in- difference between median and ulnar motor distal latencies- test with the rate of 15.5% and the lowest false positive result was in- difference between median and ulnar sensory distal latencies of digit 4- test with the rate of 0%. Conclusion: This study revealed that tests which evaluate the differences between median and ulnar or radial nerves sensory distal latency (in the finger 4 and or 1, respectively, had less false positive results, and are more reliable in suspected cases of this syndrome. Also by using several different electro-diagnostic tests, rapid and efficient diagnosis can be achieved.

  18. Results of ASTM round robin testing for mode 1 interlaminar fracture toughness of composite materials

    Science.gov (United States)

    Obrien, T. Kevin; Martin, Roderick H.

    1992-01-01

    The results are summarized of several interlaboratory 'round robin' test programs for measuring the mode 1 interlaminar fracture toughness of advanced fiber reinforced composite materials. Double Cantilever Beam (DCB) tests were conducted by participants in ASTM committee D30 on High Modulus Fibers and their Composites and by representatives of the European Group on Fracture (EGF) and the Japanese Industrial Standards Group (JIS). DCB tests were performed on three AS4 carbon fiber reinforced composite materials: AS4/3501-6 with a brittle epoxy matrix; AS4/BP907 with a tough epoxy matrix; and AS4/PEEK with a tough thermoplastic matrix. Difficulties encountered in manufacturing panels, as well as conducting the tests are discussed. Critical issues that developed during the course of the testing are highlighted. Results of the round robin testing used to determine the precision of the ASTM DCB test standard are summarized.

  19. FACTORS AFFECTING RESULT IN CHINESE PROFICIENCY TEST (HSK LEVEL 6 READING SECTION AND PREPARATION STRATEGIES

    Directory of Open Access Journals (Sweden)

    Sri Haryanti

    2015-02-01

    Full Text Available Chinese proficiency test (HSK is an internationally standardized exam which tests and rates Chinese language proficiency. The highest level in this test is level 6. The writing part of the test consists of 3 (three parts, namely, (1 listening, (2 reading, (3 writing. Furthermore, the reading part is made of 4 components. Level 6 of this test implies a high degree of difficulty. This paper specifically looked on how to prepare effectively for participants to be able to work on the reading part in order to achieve best result. This article used the methods of literature review and observational study as well as field research and would also incorporate the authors personal experience in taking the test into recommending strategies for doing the reading part in a level 6 HSK test. Finally, research suggested several techniques and tips that might assist participants in achieving maximum scores in handling the reading part of level 6 HSK test.

  20. FACTORS AFFECTING RESULT IN CHINESE PROFICIENCY TEST (HSK LEVEL 6: READING SECTION AND PREPARATION STRATEGIES

    Directory of Open Access Journals (Sweden)

    Sri Haryanti

    2013-11-01

    Full Text Available Chinese Proficiency Test (HSK is an internationally standardized exam which tests and rates Chinese language proficiency. The highest level in this test is level 6. The writing part of the test consists of 3 (three parts, namely, (1 listening, (2 reading, (3 writing. Furthermore, the reading part is made of 4 components. Level 6 of this test implies a high degree of difficulty. This paper specifically looked on how to prepare effectively for participants to be able to work on the reading part in order to achieve best result. This article used the methods of literature review and observational study as well as field research and would also incorporate the author’s personal experience in taking the test into recommending strategies for doing the reading part in a level 6 HSK test. Finally, research suggested several techniques and tips that might assist participants in achieving maximum scores in handling the reading part of level 6 HSK test.

  1. The effect of sample handling on cross sectional HIV incidence testing results.

    Directory of Open Access Journals (Sweden)

    Oliver Laeyendecker

    Full Text Available OBJECTIVE(S: To determine if mishandling prior to testing would make a sample from a chronically infected subject appear recently infected when tested by cross-sectional HIV incidence assays. METHODS: Serum samples from 31 subjects with chronic HIV infection were tested. Samples were subjected to different handling conditions, including incubation at 4 °C, 25 °C and 37 °C, for 1, 3, 7 or 15 days prior to testing. Samples were also subjected to 1,3, 7 and 15 freeze-thaw cycles prior to testing. Samples were tested using the BED capture enzyme immuno assay (BED-CEIA, Vironostika-less sensitive (V-LS, and an avidity assay using the Genetic Systems HIV-1/HIV-2 plus O EIA (avidity assay. RESULTS: Compared to the sample that was not subjected to any mishandling conditions, for the BED-CEIA, V-LS and avidity assay, there was no significant change in test results for samples incubated at 4 °C or 25 °C prior to testing. No impact on test results occurred after 15 freeze-thaw cycles. A decrease in assay results was observed when samples were held for 3 days or longer at 37 °C prior to testing. CONCLUSIONS: Samples can be subjected up to 15 freeze-thaw cycles without affecting the results the BED-CEIA, Vironostika-LS, or avidity assays. Storing samples at 4 °C or 25 °C for up to fifteen days prior to testing had no impact on test results. However, storing samples at 37°C for three or more days did affect results obtained with these assays.

  2. Direct Release of Test Results to Patients Increases Patient Engagement and Utilization of Care.

    Directory of Open Access Journals (Sweden)

    Francesca Pillemer

    Full Text Available An important focus for meaningful use criteria is to engage patients in their care by allowing them online access to their health information, including test results. There has been little evaluation of such initiatives. Using a mixed methods analysis of electronic health record data, surveys, and qualitative interviews, we examined the impact of allowing patients to view their test results via patient portal in one large health system. Quantitative data were collected for new users and all users of the patient portal. Qualitative interviews occurred with patients who had received an HbA1c or abnormal Pap result. Survey participants were active patient portal users. Our main measures were patient portal usage, factors associated with viewing test results and utilizing care, and patient and provider experiences with patient portal and direct release. Usage data show 80% of all patient portal users viewed test results during the year. Of survey respondents, 82.7% noted test results to be a very useful feature and 70% agreed that patient portal has made their provider more accessible to them. Interviewed patients reported feeling they should have direct access to test results and identified the ability to monitor results over time and prepare prior to communicating with a provider as benefits. In interviews, both patients and physicians reported instances of test results leading to unnecessary patient anxiety. Both groups noted the benefits of results released with provider interpretation. Quantitative data showed patient utilization to increase with viewing test results online, but this effect is mitigated when results are manually released by physicians. Our findings demonstrate that patient portal access to test results was highly valued by patients and appeared to increase patient engagement. However, it may lead to patient anxiety and increase rates of patient visits. We discuss how such unintended consequences can be addressed and larger

  3. T-SPOT.TB Test(R) results in adults with Mycobacterium avium complex pulmonary disease.

    Science.gov (United States)

    Adams, Lisa V; Waddell, Richard D; Von Reyn, C Fordham

    2008-01-01

    The tuberculin skin test is limited by its inability to distinguish between infection with Mycobacterium tuberculosis and non-tuberculous mycobacteria (NTM). Newer interferon-gamma release assays using ESAT-6 and CFP-10 antigens should have a higher specificity for tuberculosis but have not been widely tested in adults with pulmonary disease due to NTM. In this study, we tested the T-SPOT.TB Test in patients with pulmonary disease due to Mycobacterium avium complex (MAC), the most common disease-causing NTM. Fourteen patients with prior culture-confirmed pulmonary disease due to MAC, 10 patients with prior culture-confirmed tuberculosis and 4 healthy controls were interviewed and tested with the T-SPOT.TB Test. 13 patients with MAC disease and 4 healthy subjects (negative controls) had non-reactive T-SPOT.TB results and 10 patients with prior tuberculosis (positive controls) had reactive results. One patient with MAC disease had a minimally reactive result on initial testing and a non-reactive result on re-testing. The T-SPOT.TB Test had a specificity of 94% for distinguishing between patients with prior MAC disease and prior tuberculosis disease, and will be useful in low tuberculosis prevalence settings where most mycobacterial infections are due to MAC. Reactions to the T-SPOT.TB Test may persist months to years after treatment of tuberculosis.

  4. A Nuclear Interaction Model for Understanding Results of Single Event Testing with High Energy Protons

    Science.gov (United States)

    Culpepper, William X.; ONeill, Pat; Nicholson, Leonard L.

    2000-01-01

    An internuclear cascade and evaporation model has been adapted to estimate the LET spectrum generated during testing with 200 MeV protons. The model-generated heavy ion LET spectrum is compared to the heavy ion LET spectrum seen on orbit. This comparison is the basis for predicting single event failure rates from heavy ions using results from a single proton test. Of equal importance, this spectra comparison also establishes an estimate of the risk of encountering a failure mode on orbit that was not detected during proton testing. Verification of the general results of the model is presented based on experiments, individual part test results, and flight data. Acceptance of this model and its estimate of remaining risk opens the hardware verification philosophy to the consideration of radiation testing with high energy protons at the board and box level instead of the more standard method of individual part testing with low energy heavy ions.

  5. ELEFUNT test results under FX/FORTRAN Version 1. 0 on the Alliant FX/8

    Energy Technology Data Exchange (ETDEWEB)

    Cody, W.J.

    1986-07-01

    This paper summarizes and analyzes the results of running various programs designed to test the arithmetic and the Fortran elementary and intrinsic function packages. The programs run include MACHAR and the ELEFUNT suite of transportable Fortran test programs, from the Software Manual for the Elementary Functions by Cody and Waite, the Fortran version of the arithmetic test program PARANOIA, and the prototype programs from the nascent INTFUNT test suite for intrinsic functions. All tests were run using Release 1.0 of FX/Fortran under Release 1.0 of the Concentrix operating system. 7 refs., 4 tabs.

  6. Dealing with dissonance: responding to an incongruent test result in a new media environment.

    Science.gov (United States)

    Vraga, Emily K

    2011-11-01

    In a new media environment replete with opportunities to test and express political identity, this study examines how people respond when confronted with a political test result that contradicts their partisan affiliation. An incongruent test result should produce motivated processing, but only when individuals do not dismiss the incongruent result will they experience dissonance and alter their social identification. Using a series of experiments, the results of this study supported these hypotheses. Implications of these findings for political psychology and message response are discussed.

  7. Initial Results from the Third Round of Remediated Nitrate Salt Surrogate Formulation and Testing

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Geoffrey Wayne [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Leonard, Philip [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hartline, Ernest Leon [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tian, Hongzhao [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-04-20

    High explosives science and technology (M-7) is currently working on the third round of formulation and testing of Remediated nitrate salt (RNS) surrogates. This report summarizes the calorimetry results from the 15% sWheat mixtures. All formulation and testing was carried out according to PLAN-TA9-2443 Rev B, "Remediated Nitrate Salt (RNS) surrogate formulation and testing standard procedure", released February 16, 2016. Results from the first and second rounds of formulation and testing were documented in memoranda M7-16-6042 and M7-16-6053.

  8. Characteristics, finite element analysis, test description, and preliminary test results of the STM4-120 kinematic Stirling engine

    Science.gov (United States)

    Linker, K. L.; Rawlinson, K. S.; Smith, G.

    1991-10-01

    The Department of Energy's Solar Thermal Program has, as one of its program elements, the development and evaluation of conversion device technologies applicable to dish-electric systems. The primary research and development combines a conversion device (heat engine), solar receiver, and generator mounted at the focus of a parabolic dish concentrator. The Stirling-cycle heat engine was identified as the conversion device for dish-electric with the most potential for meeting the program's goals for efficiency, reliability, and installed cost. To advance the technology toward commercialization, Sandia National Laboratories has acquired a Stirling Thermal Motors, Inc. kinematic Stirling engine, STM4-120, for evaluation. The engine is being bench-tested at Sandia's Engine Test Facility and will be combined later with a solar receiver for on-sun evaluation. This report presents the engine characteristics, finite element analyses of critical engine components, test system layout, instrumentation, and preliminary performance results from the bench test.

  9. Buckling Test Results from the 8-Foot-Diameter Orthogrid-Stiffened Cylinder Test Article TA01. [Test Dates: 19-21 November 2008

    Science.gov (United States)

    Hilburger, Mark W.; Waters, W. Allen, Jr.; Haynie, Waddy T.

    2015-01-01

    Results from the testing of cylinder test article SBKF-P2-CYLTA01 (referred to herein as TA01) are presented. The testing was conducted at the Marshall Space Flight Center (MSFC), November 19?21, 2008, in support of the Shell Buckling Knockdown Factor (SBKF) Project.i The test was used to verify the performance of a newly constructed buckling test facility at MSFC and to verify the test article design and analysis approach used by the SBKF project researchers. TA01 is an 8-foot-diameter (96-inches), 78.0-inch long, aluminum-lithium (Al-Li), orthogrid-stiffened cylindrical shell similar to those used in current state-of-the-art launch vehicle structures and was designed to exhibit global buckling when subjected to compression loads. Five different load sequences were applied to TA01 during testing and included four sub-critical load sequences, i.e., loading conditions that did not cause buckling or material failure, and one final load sequence to buckling and collapse. The sub-critical load sequences consisted of either uniform axial compression loading or combined axial compression and bending and the final load sequence subjected TA01 to uniform axial compression. Traditional displacement transducers and strain gages were used to monitor the test article response at nearly 300 locations and an advanced digital image correlation system was used to obtain low-speed and high-speed full-field displacement measurements of the outer surface of the test article. Overall, the test facility and test article performed as designed. In particular, the test facility successfully applied all desired load combinations to the test article and was able to test safely into the postbuckling range of loading, and the test article failed by global buckling. In addition, the test results correlated well with initial pretest predictions.

  10. Allergic contact dermatitis to benzocaine: the importance of concomitant positive patch test results.

    Science.gov (United States)

    González-Rodríguez, A J; Gutiérrez-Paredes, E M; Revert Fernández, Á; Jordá-Cuevas, E

    2013-03-01

    Local anesthetics are widely used in clinical practice, and adverse effects are not uncommon. Delayed hypersensitivity reactions are among the most common effects, but immediate-type reactions may also occur. Patch testing should be considered in patients with hypersensitivity reactions. We present a case of allergic contact dermatitis to benzocaine that was detected incidentally by patch testing and highlight the importance of correctly interpreting patch test results when there are concomitant positive reactions.

  11. Results of S5 CH tests with an ARL (Aerospace Research Laboratory) cascade

    Science.gov (United States)

    Fourmaux, A.

    1984-01-01

    As part of a research agreement between Iowa State University of Science and Technology (ISU) and ONERA, a blade cascade designed and already tested in the United States was manufactured and tested in France. The ONERA cascade wind tunnel and mock-up are described. Attention is focused on defining the upstream conditions of the cascade. Experimental results are presented, as well as comparisons with tests conducted by Detroit Diesel Allison (DDA) in the United States.

  12. Performance of Charcoal Cookstoves for Haiti, Part 2: Results from the Controlled Cooking Test

    Energy Technology Data Exchange (ETDEWEB)

    Lask, Kathleen; Jones, Jennifer; Booker, Kayje; Ceballos, Cristina; Yang, Nina; Gadgil, Ashok

    2011-11-30

    Five charcoal cookstoves were tested using a Controlled Cooking Test (CCT) developed from cooking practices in Haiti. Cookstoves were tested for total burn time, specific fuel consumption, and emissions of carbon monoxide (CO), carbon dioxide (CO2), and the ratio of carbon monoxide to carbon dioxide (CO/CO2). These results are presented in this report along with LBNL testers’ observations regarding the usability of the stoves.

  13. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 5 Full-Scale Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Gary Blythe; MariJon Owens

    2007-12-01

    involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests and the full-scale test using high-sulfur coal were completed in 2005 and 2006 and have been previously reported. This topical report presents the results from the Task 5 full-scale additive tests, conducted at Southern Company's Plant Yates Unit 1. Both additives were tested there.

  14. Analytical results of a long-term aquifer test conducted near the Rio Grande, Albuquerque, New Mexico, with a section on piezometric-extensometric test results

    Science.gov (United States)

    Thorn, Conde R.; Heywood, Charles E.

    2001-01-01

    The City of Albuquerque, New Mexico, is interested in gaining a better understanding, both quantitative and qualitative, of the aquifer system in and around Albuquerque. Currently (2000), the City of Albuquerque and surrounding municipalities are completely dependent on ground-water reserves for their municipal water supply. This report presents the results of a long-term aquifer test conducted near the Rio Grande in Albuquerque. The long-term aquifer test was conducted during the winter of 1994-95. The City of Albuquerque Griegos 1 water production well was pumped continuously for 54 days at an average pumping rate of 2,331 gallons per minute. During the 54-day pumping and a 30-day recovery period, water levels were recorded in a monitoring network that consisted of 3 production wells and 19 piezometers located at nine sites. These wells and piezometers were screened in river alluvium and (or) the upper and middle parts of the Santa Fe Group aquifer system. In addition to the measurement of water levels, aquifer-system compaction was monitored during the aquifer test by an extensometer. Well-bore video and flowmeter surveys were conducted in the Griegos 1 water production well at the end of the recovery period to identify the location of primary water- producing zones along the screened interval. Analytical results from the aquifer test presented in this report are based on the methods used to analyze a leaky confined aquifer system and were performed using the computer software package AQTESOLV. Estimated transmissivities for the Griegos 1 and 4 water production wells ranged from 10,570 to 24,810 feet squared per day; the storage coefficient for the Griegos 4 well was 0.0025. A transmissivity of 13,540 feet squared per day and a storage coefficient of 0.0011 were estimated from the data collected from a piezometer completed in the production interval of the Griegos 1 well.

  15. Preliminary test results in support of integrated EPP and SMT design methods development

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yanli [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jetter, Robert I. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sham, T. -L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-02-09

    The proposed integrated Elastic Perfectly-Plastic (EPP) and Simplified Model Test (SMT) methodology consists of incorporating a SMT data-based approach for creep-fatigue damage evaluation into the EPP methodology to avoid using the creep-fatigue interaction diagram (the D diagram) and to minimize over-conservatism while properly accounting for localized defects and stress risers. To support the implementation of the proposed code rules and to verify their applicability, a series of thermomechanical tests have been initiated. One test concept, the Simplified Model Test (SMT), takes into account the stress and strain redistribution in real structures by including representative follow-up characteristics in the test specimen. The second test concept is the two-bar thermal ratcheting tests with cyclic loading at high temperatures using specimens representing key features of potential component designs. This report summaries the previous SMT results on Alloy 617, SS316H and SS304H and presents the recent development on SMT approach on Alloy 617. These SMT specimen data are also representative of component loading conditions and have been used as part of the verification of the proposed integrated EPP and SMT design methods development. The previous two-bar thermal ratcheting test results on Alloy 617 and SS316H are also summarized and the new results from two bar thermal ratcheting tests on SS316H at a lower temperature range are reported.

  16. Ballistic penetration test results for Ductal and ultra-high performance concrete samples.

    Energy Technology Data Exchange (ETDEWEB)

    Reinhart, William Dodd; Thornhill, Tom Finley, III (KTech)

    2010-03-01

    This document provides detailed test results of ballistic impact experiments performed on several types of high performance concrete. These tests were performed at the Sandia National Laboratories Shock Thermodynamic Applied Research Facility using a 50 caliber powder gun to study penetration resistance of concrete samples. This document provides test results for ballistic impact experiments performed on two types of concrete samples, (1) Ductal{reg_sign} concrete is a fiber reinforced high performance concrete patented by Lafarge Group and (2) ultra-high performance concrete (UHPC) produced in-house by DoD. These tests were performed as part of a research demonstration project overseen by USACE and ERDC, at the Sandia National Laboratories Shock Thermodynamic Applied Research (STAR) facility. Ballistic penetration tests were performed on a single stage research powder gun of 50 caliber bore using a full metal jacket M33 ball projectile with a nominal velocity of 914 m/s (3000 ft/s). Testing was observed by Beverly DiPaolo from ERDC-GSL. In all, 31 tests were performed to achieve the test objectives which were: (1) recovery of concrete test specimens for post mortem analysis and characterization at outside labs, (2) measurement of projectile impact velocity and post-penetration residual velocity from electronic and radiographic techniques and, (3) high-speed photography of the projectile prior to impact, impact and exit of the rear surface of the concrete construct, and (4) summarize the results.

  17. An assessment of wind tunnel test data on flexible thermal protection materials and results of new fatigue tests of threads

    Science.gov (United States)

    Coe, Charles F.

    1985-01-01

    Advanced Flexible Reusable Surface Insulation (AFRSI) was developed as a replacement for the low-temperature (white) tiles on the Space Shuttle. The first use of the AFRSI for an Orbiter flight was on the OMS POD of Orbiter (OV-099) for STS-6. Post flight examination after STS-6 showed that damage had occurred to the AFRSI during flight. The failure anomaly between previous wind-tunnel tests and STS-6 prompted a series of additional wind tunnel tests to gain an insight as to the cause of the failure. An assessment of all the past STS-6 wind tunnel tests pointed out the sensitivity of the test results to scaling of dynamic loads due to the difference of boundary layer thickness, and the material properties as a result of exposure to heating. The thread component of the AFRSI was exposed to fatigue testing using an apparatus that applied pulsating aerodynamic loads on the threads similar to the loads caused by an oscillating shock. Comparison of the mean values of the number-of-cycles to failure showed that the history of the thread was the major factor in its performance. The thread and the wind tunnel data suggests a mechanism of failure for the AFRSI.

  18. 76 FR 19952 - Not Applying the Mark of Inspection Pending Certain Test Results

    Science.gov (United States)

    2011-04-11

    ... livestock carcasses subject to FSIS testing for such veterinary drugs as antibiotics, sulfonamides, or... consumed chicken salad that had been released into commerce before the FSIS test results were returned as... (for example antibiotics and antifungals). EPA establishes safe methods of use for chemicals...

  19. Radiation Testing on State-of-the-Art CMOS: Challenges, Plans, and Preliminary Results

    Science.gov (United States)

    LaBel, Kenneth A.; Cohn, Lewis M.

    2009-01-01

    At GOMAC 2007 and 2008, we discussed a variety of challenges for radiation testing of modern semiconductor devices and technologies [1, 2]. In this presentation, we provide more specific details in this on-going investigation focusing on out-of-the-box lessons observed for providing radiation effects assurances as well as preliminary test results.

  20. Parents' responses to disclosure of genetic test results of their children

    NARCIS (Netherlands)

    Grosfeld, FJM; Beemer, FA; Lips, CJM; ten Kroode, HFJ

    2000-01-01

    The psychological reactions of 22 parental couples and 3 single parents were investigated after disclosure of genetic test results of their children. The children were tested for the early-onset, monogenetic cancer disorder multiple endocrine neoplasia type 2. Participants came from 13 different fam

  1. NOx emissions of Euro 5 diesel vans - test results in the lab and on the road

    NARCIS (Netherlands)

    Kadijk, G.; Ligterink, N.E.; Mensch, P. van; Smokers, R.T.M.

    2016-01-01

    This document contains results from emission tests, carried out by TNO in the period 2010-20151. The specific focus is on NOx emissions of Euro 5 light commercial vehicles (vans). The emission tests were carried out as part of a project conducted by TNO for the Dutch Ministry of Infrastructure and t

  2. Results of the 2015 Relationship Testing Workshop of the English Speaking Working Group

    DEFF Research Database (Denmark)

    Friis, Susanne Lunøe; Hallenberg, Charlotte; Simonsen, Bo Thisted;

    2015-01-01

    Annually, members of the English Speaking Working Group of the International Society for Forensic Genetics are invited to participate in a Relationship Testing Workshop. In 2015, 64 laboratories participated. Here, we present the results from the 2015 workshop, which included relationship testing...

  3. High Fidelity, Fuel-Like Thermal Simulators for Non-Nuclear Testing: Analysis and Initial Test Results

    Science.gov (United States)

    Bragg-Sitton, Shannon M.; Dickens, Ricky; Dixon, David; Kapernick, Richard

    2007-01-01

    Non-nuclear testing can be a valuable tool in the development of a space nuclear power system, providing system characterization data and allowing one to work through various fabrication, assembly and integration issues without the cost and time associated with a full ground nuclear test. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Testing with non-optimized heater elements allows one to assess thermal, heat transfer. and stress related attributes of a given system, but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. High fidelity thermal simulators that match both the static and the dynamic fuel pin performance that would be observed in an operating, fueled nuclear reactor can vastly increase the value of non-nuclear test results. With optimized simulators, the integration of thermal hydraulic hardware tests with simulated neutronic response provides a bridge between electrically heated testing and fueled nuclear testing. By implementing a neutronic response model to simulate the dynamic response that would be expected in a fueled reactor system, one can better understand system integration issues, characterize integrated system response times and response characteristics and assess potential design improvements at relatively small fiscal investment. Initial conceptual thermal simulator designs are determined by simple one-dimensional analysis at a single axial location and at steady state conditions; feasible concepts are then input into a detailed three-dimensional model for comparison to expected fuel pin performance. Static and dynamic fuel pin performance for a proposed reactor design is determined using SINDA/FLUINT thermal analysis software, and comparison is made between the expected nuclear performance and the performance of conceptual thermal simulator designs. Through a series of iterative analyses, a conceptual high fidelity design is developed

  4. Test results of a HTS power transformer connected to a power grid

    Science.gov (United States)

    Kimura, H.; Honda, K.; Hayashi, H.; Tsutsumi, K.; Iwakuma, M.; Funaki, K.; Bohno, T.; Tomioka, A.; Yagi, Y.; Maruyama, H.; Ohashi, K.

    2002-08-01

    A 22 kV/6.9 kV-1 MVA high- Tc superconducting (HTS) power transformer has been developed as a prototype with single-phase part of a 3 MVA HTS power transformer. The prototype unit is cooled by a continuous subcooled liquid nitrogen (LN 2) supply system with cryocoolers. During the field tests, the HTS transformer was connected to a distribution line at Imajuku substation (Kyushu Electric Power Co., Inc.) in Fukuoka, and inrush-current test and a long-term operation test were implemented. The test results demonstrated the HTS power transformer's applicability to a power grid.

  5. A Comparison Study of Students’ Performance in Pre and Post Result of A Mathematics Competency Test

    Directory of Open Access Journals (Sweden)

    Khashi’ie Najiyah Safwa

    2017-01-01

    Full Text Available The objective of this study was to compare the performance of Engineering Technology (ET students’ in a Pre and Post Mathematics Competency Test during their first year of study at the Faculty of Engineering Technology (FTK, Universiti Teknikal Malaysia Melaka (UTeM. This article also aims to examine the student’s understanding in the area of Mathematics, particularly in Algebra, Trigonometry and Functions. A total of 176 first year students from the Department of Mechanical Engineering Technology (JTKM were chosen to answer the Mathematics Competency Test. The pre-test was held in the first week of the semester, while the post-test was held during the second semester. The results showed that the students’ performance in post-test was better compared to that pre-test. However, statistical analysis on students’ performance by each question showed that most of the students did not understand the basic concepts in Algebra, Trigonometry and Functions.

  6. Surrogate/spent fuel sabotage aerosol ratio testing:phase 1 summary and results.

    Energy Technology Data Exchange (ETDEWEB)

    Vigil, Manuel Gilbert; Sorenson, Ken Bryce; Lange, F. (Gesellschaft fur Anlagen- und reaktorsicherheit (GRS), Germany); Nolte, O. (Fraunhofer Institut fur Toxikologie und Experimentelle Medizin, Germany); Koch, W. (Fraunhofer Institut fur Toxikologie und Experimentelle Medizin, Germany); Dickey, Roy R.; Yoshimura, Richard Hiroyuki; Molecke, Martin Alan; Autrusson, Bruno (Institut de Radioprotection et de Surete Nucleaire (IRSN), France); Young, F. I. (U.S. Nuclear Regulatory Commission); Pretzsch, Gunter Guido (Gesellschaft fur Anlagen- und reaktorsicherheit (GRS), Germany)

    2005-10-01

    This multinational test program is quantifying the aerosol particulates produced when a high energy density device (HEDD) impacts surrogate material and actual spent fuel test rodlets. The experimental work, performed in four consecutive test phases, has been in progress for several years. The overall program provides needed data that are relevant to some sabotage scenarios in relation to spent fuel transport and storage casks, and associated risk assessments. This program also provides significant political benefits in international cooperation for nuclear security related evaluations. The spent fuel sabotage--aerosol test program is coordinated with the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC), and supported by both the U.S. Department of Energy and Nuclear Regulatory Commission. This report summarizes the preliminary, Phase 1 work performed in 2001 and 2002 at Sandia National Laboratories and the Fraunhofer Institute, Germany, and documents the experimental results obtained, observations, and preliminary interpretations. Phase 1 testing included: performance quantifications of the HEDD devices; characterization of the HEDD or conical shaped charge (CSC) jet properties with multiple tests; refinement of the aerosol particle collection apparatus being used; and, CSC jet-aerosol tests using leaded glass plates and glass pellets, serving as representative brittle materials. Phase 1 testing was quite important for the design and performance of the following Phase 2 test program and test apparatus.

  7. Engine systems analysis results of the Space Shuttle Main Engine redesigned powerhead initial engine level testing

    Science.gov (United States)

    Sander, Erik J.; Gosdin, Dennis R.

    1992-01-01

    Engineers regularly analyze SSME ground test and flight data with respect to engine systems performance. Recently, a redesigned SSME powerhead was introduced to engine-level testing in part to increase engine operational margins through optimization of the engine internal environment. This paper presents an overview of the MSFC personnel engine systems analysis results and conclusions reached from initial engine level testing of the redesigned powerhead, and further redesigns incorporated to eliminate accelerated main injector baffle and main combustion chamber hot gas wall degradation. The conclusions are drawn from instrumented engine ground test data and hardware integrity analysis reports and address initial engine test results with respect to the apparent design change effects on engine system and component operation.

  8. Results of the latest transient well pressure tests at Cerro Prieto

    Energy Technology Data Exchange (ETDEWEB)

    Abril G, A.; Vargas G, C.

    1981-01-01

    The equipment used in the interference and two-rate flow tests carried out at the Cerro Prieto geothermal field during 1980 are described. The results of two interference tests are presented, one between wells M-110 and M-104, and the other between wells M-7 and Q-757. The data was interpreted using type curve matching analysis. Results of two-rate flow tests carried out in wells M-102 and M-7 are also discussed. A technique for making two-rate flow tests is proposed. This approach, which attempts to avoid the uncertainty of present flow-rate measurements, makes use of devices for direct measurements of separated water and steam. Conclusions based on the above interpretations and recommendations for future tests are presented.

  9. Testing and Oxygen Assessment Results for a Next Generation Extravehicular Activity Portable Life Support System Fan

    Science.gov (United States)

    Paul, Heather L.; Jennings, Mallory A.; Rivera, Fatonia L.; Martin, Devin

    2011-01-01

    NASA is designing a next generation Extravehicular Activity (EVA) Portable Life Support System (PLSS) for use in future surface exploration endeavors. To meet the new requirements for ventilation flow at nominal and buddy modes, a fan has been developed and tested. This paper summarizes the results of the performance and life cycle testing efforts conducted at the NASA Johnson Space Center. Additionally, oxygen compatibility assessment results from an evaluation conducted at White Sands Test Facility (WSTF) are provided, and lessons learned and future recommendations are outlined.

  10. Cassini RTG Acceptance Test Results and RTG Performance on Galileo and Ulysses

    Science.gov (United States)

    Kelly, C. E.; Klee, P. M.

    1997-06-01

    Flight acceptance testing has been completed for the RTGs to be used on the Cassini spacecraft which is scheduled for an October 6, 1997 launch to Saturn. The acceptance test program includes vibration tests, magnetic field measurements, properties (weight and c.g.) and thermal vacuum test. This paper presents The thermal vacuum test results. Three RTGs are to be used, F 2, F 6, and F 7. F 5 is tile back up RTG, as it was for the Galileo and Ulysses missions launched in 1989 and 1990, respectively. RTG performance measured during the thermal vacuum tests carried out at die Mound Laboratory facility met all specification requirements. Beginning of mission (BOM) and end of mission (EOM) power predictions have been made based on than tests results. BOM power is predicted to be 888 watts compared to the minimum requirement of 826 watts. Degradation models predict the EOM power after 16 years is to be 640 watts compared to a minimum requirement of 596 watts. Results of small scale module tests are also showing. The modules contain couples from the qualification and flight production runs. The tests have exceeded 28,000 hours (3.2 years) and are continuing to provide increased confidence in the predicted long term performance of the Cassini RTGs. All test results indicate that the power requirements of the Cassini spacecraft will be met. BOM and EOM power margins of over five percent are predicted. Power output from telemetry for the two Galileo RTGs are shown from the 1989 launch to the recent Jupiter encounter. Comparisons of predicted, measured and required performance are shown. Telemetry data are also shown for the RTG on the Ulysses spacecraft which completed its planned mission in 1995 and is now in the extended mission.

  11. Developing a reproducible non-line-of-sight experimental setup for testing wireless medical device coexistence utilizing ZigBee.

    Science.gov (United States)

    LaSorte, Nickolas J; Rajab, Samer A; Refai, Hazem H

    2012-11-01

    The integration of heterogeneous wireless technologies is believed to aid revolutionary healthcare delivery in hospitals and residential care. Wireless medical device coexistence is a growing concern given the ubiquity of wireless technology. In spite of this, a consensus standard that addresses risks associated with wireless heterogeneous networks has not been adopted. This paper serves as a starting point by recommending a practice for assessing the coexistence of a wireless medical device in a non-line-of-sight environment utilizing 802.15.4 in a practical, versatile, and reproducible test setup. This paper provides an extensive survey of other coexistence studies concerning 802.15.4 and 802.11 and reports on the authors' coexistence testing inside and outside an anechoic chamber. Results are compared against a non-line-of-sight test setup. Findings relative to co-channel and adjacent channel interference were consistent with results reported in the literature.

  12. ANALYSIS AND QUANTITATIVE ASSESSMENT FOR RESULTS OF EDUCATIONAL PROGRAMS APPLICATION BY MEANS OF DIAGNOSTIC TESTS

    Directory of Open Access Journals (Sweden)

    E. L. Kon

    2015-07-01

    Full Text Available Subject of Research.The problem actuality for creation, control and estimation of results for competence-oriented educational programs is formulated and proved. Competences elements and components, assembled in modules, course units and parts of educational program, are defined as objects of control. Specific tasks of proficiency examination for competences and their components are stated; subject matter of the paper is formulated. Methods of Research. Some adapted statements and methods of technical science are offered to be applied for control tasks solution, decoding and estimation of education results. The approach to quantitative estimation of testing results with the use of additive integrated differential criterion of estimation is offered. Main Results. Statements, defining conditions of certain and uncertain (indeterminacy decision-making about proficiency examination for elements of discipline components controlled by test according to test realization results, are formulated and proved. Probabilistic characteristicsof both decision-making variants are estimated. Variants of determinate and fuzzy logic mathematic methods application for decreasing decision-making indeterminancy are offered; further research direction is selected for development of methods and algorithms for results decoding of diagnostic tests set realization. Practical Relevance. It is shown, that proposed approach to quantitative estimation of testing results will give the possibility to automate the procedure of formation and analysis for education results, specified in the competence format.

  13. Results from a round robin test for the ecotoxicological evaluation of construction products using two leaching tests and an aquatic test battery.

    Science.gov (United States)

    Gartiser, Stefan; Heisterkamp, Ines; Schoknecht, Ute; Burkhardt, Michael; Ratte, Monika; Ilvonen, Outi; Brauer, Frank; Brückmann, Jan; Dabrunz, André; Egeler, Philipp; Eisl, Andrea-Maria; Feiler, Ute; Fritz, Ines; König, Sabina; Lebertz, Herbert; Pandard, Pascal; Pötschke, Gabriele; Scheerbaum, Dirk; Schreiber, Frank; Soldán, Přemysl; Weiß, Roland; Weltens, Reinhilde

    2017-05-01

    A European round robin test according to ISO 5725-2 was conceptually prepared, realised, and evaluated. The aim was to determine the inter-laboratory variability of the overall process for the ecotoxicological characterization of construction products in eluates and bioassays. To this end, two construction products BAM-G1 (granulate) and HSR-2 (roof sealing sheet), both made of EPDM polymers (rubber), were selected. The granular construction product was eluted in a one stage batch test, the planar product in the Dynamic Surface Leaching test (DSLT). A total of 17 laboratories from 5 countries participated in the round robin test: Germany (12), Austria (2), Belgium (1), Czech Republic (1) and France (1). A test battery of four standardised ecotoxicity tests with algae, daphnia, luminescent bacteria and zebrafish eggs was used. As toxicity measures, EC50 and LID values were calculated. All tests, except the fish egg test, were basically able to demonstrate toxic effects and the level of toxicity. The reproducibility of test results depended on the test specimens and the test organisms. Generally, the variability of the EC50 or LID values increased with the overall level of toxicity. For the very toxic BAM-G1 eluate a relative high variability of CV = 73%-110% was observed for EC50 in all biotests, while for the less toxic HSR-2 eluate the reproducibility of EC50 varied with sensitivity: it was very good (CV = 9.3%) for the daphnia test with the lowest sensitivity, followed by the algae test (CV = 36.4%). The luminescent bacteria test, being the most sensitive bioassay for HSR-2 Eluate, showed the highest variability (CV = 74.8%). When considering the complex overall process the reproducibility of bioassays with eluates from construction products was acceptable.

  14. Recommendations for reporting results of diagnostic genetic testing (biochemical, cytogenetic and molecular genetic).

    Science.gov (United States)

    Claustres, Mireille; Kožich, Viktor; Dequeker, Els; Fowler, Brain; Hehir-Kwa, Jayne Y; Miller, Konstantin; Oosterwijk, Cor; Peterlin, Borut; van Ravenswaaij-Arts, Conny; Zimmermann, Uwe; Zuffardi, Orsetta; Hastings, Ros J; Barton, David E

    2014-02-01

    Genetic test results can have considerable importance for patients, their parents and more remote family members. Clinical therapy and surveillance, reproductive decisions and genetic diagnostics in family members, including prenatal diagnosis, are based on these results. The genetic test report should therefore provide a clear, concise, accurate, fully interpretative and authoritative answer to the clinical question. The need for harmonizing reporting practice of genetic tests has been recognised by the External Quality Assessment (EQA), providers and laboratories. The ESHG Genetic Services Quality Committee has produced reporting guidelines for the genetic disciplines (biochemical, cytogenetic and molecular genetic). These guidelines give assistance on report content, including the interpretation of results. Selected examples of genetic test reports for all three disciplines are provided in an annexe.

  15. Psychiatric patients' return for HIV/STI test results in mental health centers

    Directory of Open Access Journals (Sweden)

    Ana Paula Souto Melo

    2012-04-01

    Full Text Available OBJECTIVE: To assess individual and/or health service factors associated with patients returning for results of HIV or sexually transmitted infection (STI tests in mental health centers. METHODS: Cross-sectional national multicenter study among 2,080 patients randomly selected from 26 Brazilian mental health centers in 2007. Multilevel logistic regression was used to assess the effect of individual (level 1 and mental health service characteristics (level 2 on receipt of test results. RESULTS: The rate of returning HIV/STI test results was 79.6%. Among health service characteristics examined, only condom distribution was associated with receiving HIV/STI test results, whereas several individual characteristics were independently associated including living in the same city where treatment centers are; being single; not having heard of AIDS; and not having been previously HIV tested. CONCLUSIONS: It is urgent to expand HIV/STI testing in health services which provide care for patients with potentially increased vulnerability to these conditions, and to promote better integration between mental health and health services.

  16. SMART empirical approaches for predicting field performance of PV modules from results of reliability tests

    Science.gov (United States)

    Hardikar, Kedar Y.; Liu, Bill J. J.; Bheemreddy, Venkata

    2016-09-01

    Gaining an understanding of degradation mechanisms and their characterization are critical in developing relevant accelerated tests to ensure PV module performance warranty over a typical lifetime of 25 years. As newer technologies are adapted for PV, including new PV cell technologies, new packaging materials, and newer product designs, the availability of field data over extended periods of time for product performance assessment cannot be expected within the typical timeframe for business decisions. In this work, to enable product design decisions and product performance assessment for PV modules utilizing newer technologies, Simulation and Mechanism based Accelerated Reliability Testing (SMART) methodology and empirical approaches to predict field performance from accelerated test results are presented. The method is demonstrated for field life assessment of flexible PV modules based on degradation mechanisms observed in two accelerated tests, namely, Damp Heat and Thermal Cycling. The method is based on design of accelerated testing scheme with the intent to develop relevant acceleration factor models. The acceleration factor model is validated by extensive reliability testing under different conditions going beyond the established certification standards. Once the acceleration factor model is validated for the test matrix a modeling scheme is developed to predict field performance from results of accelerated testing for particular failure modes of interest. Further refinement of the model can continue as more field data becomes available. While the demonstration of the method in this work is for thin film flexible PV modules, the framework and methodology can be adapted to other PV products.

  17. Lack of Correlation between Severity of Clinical Symptoms, Skin Test Reactivity, and Radioallergosorbent Test Results in Venom-Allergic Patients

    Directory of Open Access Journals (Sweden)

    Warrington RJ

    2006-06-01

    Full Text Available Abstract Purpose To retrospectively examine the relation between skin test reactivity, venom-specific immunoglobulin E (IgE antibody levels, and severity of clinical reaction in patients with insect venom allergy. Method Thirty-six patients (including 15 females who presented with a history of allergic reactions to insect stings were assessed. The mean age at the time of the reactions was 33.4 ± 15.1 years (range, 4-76 years, and patients were evaluated 43.6 ± 90 months (range, 1-300 months after the reactions. Clinical reactions were scored according to severity, from 1 (cutaneous manifestations only to 3 (anaphylaxis with shock. These scores were compared to scores for skin test reactivity (0 to 5, indicating the log increase in sensitivity from 1 μg/mL to 0.0001 μg/mL and radioallergosorbent test (RAST levels (0 to 4, indicating venom-specific IgE levels, from undetectable to >17.5 kilounits of antigen per litre [kUA/L]. Results No correlation was found between skin test reactivity (Spearman's coefficient = 0.15, p = .377 or RAST level (Spearman's coefficient = 0.32, p = .061 and the severity of reaction. Skin test and RAST scores both differed significantly from clinical severity (p p = .042. There was no correlation between skin test reactivity and time since reaction (Spearman's coefficient = 0.18, p = .294 nor between RAST and time since reaction (r = 0.1353, p = .438. Elimination of patients tested more than 12 months after their reaction still produced no correlation between skin test reactivity (p = .681 or RAST score (p = .183 and the severity of the clinical reaction. Conclusion In venom-allergic patients (in contrast to reported findings in cases of inhalant IgE-mediated allergy, there appears to be no significant correlation between the degree of skin test reactivity or levels of venom-specific IgE (determined by RAST and the severity of the clinical reaction.

  18. Understanding the management of electronic test result notifications in the outpatient setting

    Directory of Open Access Journals (Sweden)

    Singh Hardeep

    2011-04-01

    Full Text Available Abstract Background Notifying clinicians about abnormal test results through electronic health record (EHR -based "alert" notifications may not always lead to timely follow-up of patients. We sought to understand barriers, facilitators, and potential interventions for safe and effective management of abnormal test result delivery via electronic alerts. Methods We conducted a qualitative study consisting of six 6-8 member focus groups (N = 44 at two large, geographically dispersed Veterans Affairs facilities. Participants included full-time primary care providers, and personnel representing diagnostic services (radiology, laboratory and information technology. We asked participants to discuss barriers, facilitators, and suggestions for improving timely management and follow-up of abnormal test result notifications and encouraged them to consider technological issues, as well as broader, human-factor-related aspects of EHR use such as organizational, personnel, and workflow. Results Providers reported receiving a large number of alerts containing information unrelated to abnormal test results, many of which were believed to be unnecessary. Some providers also reported lacking proficiency in use of certain EHR features that would enable them to manage alerts more efficiently. Suggestions for improvement included improving display and tracking processes for critical alerts in the EHR, redesigning clinical workflow, and streamlining policies and procedures related to test result notification. Conclusion Providers perceive several challenges for fail-safe electronic communication and tracking of abnormal test results. A multi-dimensional approach that addresses technology as well as the many non-technological factors we elicited is essential to design interventions to reduce missed test results in EHRs.

  19. Experimental and calculation results of the integral reflood test QUENCH-15 with ZIRLO{sup TM} cladding tubes in comparison with results of previous QUENCH tests

    Energy Technology Data Exchange (ETDEWEB)

    Stuckert, J., E-mail: juri.stuckert@kit.edu [Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Birchley, J. [Paul Scherrer Institut (PSI), CH-5232 Villigen PSI (Switzerland); Grosse, M. [Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Jaeckel, B. [Paul Scherrer Institut (PSI), CH-5232 Villigen PSI (Switzerland); Steinbrueck, M. [Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany)

    2011-08-15

    thickness of inner oxide layer reaches 20% of that of the outer oxide layer. The measured hydrogen release during the QUENCH-15 test was 41 g in the pre-oxidation and transient phases and 7 g in the quench phase which are comparable with those in QUENCH-06, i.e. 32 g and 4 g, respectively. Post-test calculations were performed using a version of SCDAP/RELAP5/MOD3.2. The calculation results support the heuristic observation that there was no major difference between the influence of Zircaloy-4, M5 or ZIRLO{sup TM} for the beyond-design basis accident present conditions here studied.

  20. A rotating differential accelerometer for testing the equivalence principle in space: results from laboratory tests of a ground prototype

    Science.gov (United States)

    Nobili, A. M.; Bramanti, D.; Comandi, G. L.; Toncelli, R.; Polacco, E.

    2003-07-01

    We have proposed to test the equivalence principle (EP) in low Earth orbit with a rapidly rotating differential accelerometer (made of weakly coupled concentric test cylinders) whose rotation provides high frequency signal modulation and avoids severe limitations otherwise due to operation at room temperature [PhRvD 63 (2001) 101101]. Although the accelerometer has been conceived for best performance in absence of weight, we have designed, built and tested a variant of it at 1-g. Here we report the results of measurements performed so far. Losses measured with the full system in operation yield a quality factor only four times smaller than the value required for the proposed high accuracy EP test in space. Unstable whirl motions, which are known to arise in the system and might be a matter of concern, are found to grow as slowly as predicted and can be stabilized. The capacitance differential read-out (the mechanical parts, electronics and software for data analysis) is in all similar to what is needed in the space experiment. In the instrument described here the coupling of the test masses is 24 000 times stiffer than in the one proposed for flight, which makes it 24 000 times less sensitive to differential displacements. With this stiffness it should detect test masses separations of 1.5·10 -2 μm, while so far we have achieved only 1.5 μm, because of large perturbations—due to the motor, the ball bearings, the non-perfect verticality of the system—all of which, however, are absent in space. The effects of these perturbations should be reduced by 100 times in order to perform a better demonstration. Further instrument improvements are underway to fill this gap and also to reduce its stiffness, thus increasing its significance as a prototype of the space experiment.

  1. Comparison between tilt-table testing results performed during different periods of the day

    Directory of Open Access Journals (Sweden)

    Tan Chen Wu

    2002-10-01

    Full Text Available OBJECTIVE: To evaluate the influences of circadian variations on tilt-table testing (TTT results by comparing the positivity rate of the test performed during the morning with that of the test performed in the afternoon and to evaluate the reproducibility of the results in different periods of the day. METHODS: One hundred twenty-three patients with recurrent unexplained syncope or near-syncope referred for TTT were randomized into 2 groups. In group I, 68 patients, TTT was performed first in the afternoon and then in the morning. In group II, 55 patients, the test was performed first in the morning and then in the afternoon. RESULTS: The TTT protocol was the prolonged passive test, without drug sensitization. Twenty-nine (23.5% patients had a positive result in at least one of the periods. The positivity rate for each period was similar: 20 (16.2% patients in the afternoon and 19 (15.4% in the morning (p=1.000. Total reproducibility (positive/positive and negative/negative was observed in 49 (89% patients in group I and in 55 (81% in group II. Reproducibility of the results was obtained in 94 (90.4% patients with first negative tests but in 10 (34% patients with first positive tests. CONCLUSION: TTT could be performed during any period of the day, and even in the 2 periods to enhance positivity. Considering the low reproducibility rate of the positive tests, serial TTT to evaluate therapeutic efficacy should be performed during the same period of the day.

  2. Results from the NRC AP600 testing program at the Oregon State University APEX facility

    Energy Technology Data Exchange (ETDEWEB)

    Reyes, J.N. Jr. [Oregon State Univ., Corvallis, OR (United States); Bessette, D.E. [Nuclear regulatory Systems, Washington, DC (United States); DiMarzo, M. [Univ. of Maryland, College Park, MD (United States)

    1996-03-01

    The Department of Nuclear Engineering at Oregon State University (OSU) is performing a series of confirmatory tests for the U.S. Nuclear Regulatory Commission. These tests are being conducted in the Advanced Plant Experiment (APEX) facility which is a 1/4 length scale and 1/192 volume scale integral system simulation of the Westinghouse Advanced Passive 600 MWe (AP600) plant. The purpose of the testing program is to examine AP600 passive safety system performance, particularly during long term cooling. Thus far, OSU has successfully performed ten integral system tests for the NRC. This paper presents a description of the APEX facility and summarizes the important results of the NRC test program at OSU.

  3. Evaluation of Methacholine Challenge Test Results in Chronic Cough Patients Referring to Clinic of Pulmonary Disease

    Directory of Open Access Journals (Sweden)

    Derakhshan Deilami Gholamreza

    2009-10-01

    Full Text Available Chronic cough is a common problem in patients visiting physicians and its prevalence in different populations range from 3 to 40%. Postnasal drip, asthma and gastroesophageal reflux are the known cause of chronic cough. Although diagnosis of asthma is usually made by clinical signs and spirometeric results, methacholine challenge test is a good diagnostic test in patients who show normal physical examination and spirometeric results. In this study, the results of methacholine challenge test in chronic cough patients are investigated. This is a cross sectional study performed on patients suffering from chronic cough (over 8 weeks, who went to Pulmonary Disease Clinic of Imam Khomeini Hospital in 2006. Postnasal drip, gastroesophageal reflux was evaluated and ruled out in all patients. Then they were tested by methacholine inhalation using low to high doses of methacholine. The results of test was defined as 20% fall in FEV1 and its relationship with age, sex, history of allergic disease, family history of asthma and smoking status was investigated. 81 patients (36 female and 45 male entered this study who had mean age of 32.5 ± 13.06 years. 81.5% of patients had never smoked or closed contact with smokers, 6.2% were passive smokers, 8.6% were smokers and 3.7% had quit smoking. 37% had suffered from chronic cough less than 6 months, 11% for 6-11 months and 52% for more than 12 months. In 26% of patients, family history of asthma was present and 34.5% had a history of one type of allergy. In 29.5% the results of methacholine challenge test was positive, among them 45.8% showed an intense response and 54.2% a moderate response. The test results and its intensity had no statistically significant relationship with age, sex, smoking status, the duration of cough and family history of asthma, but the relationship between methacholine challenge test and the history of allergic disease was significant. Methacholine challenge test can be used as a

  4. Abnormal ovarian cancer screening test result: women's informational, psychological and practical needs.

    Science.gov (United States)

    Ryan, Patricia Y; Graves, Kristi D; Pavlik, Edward J; Andrykowski, Michael A

    2007-01-01

    Considerable effort has been devoted to the identification of cost-effective approaches to screening for ovarian cancer (OC). Transvaginal ultrasound (TVS) is one such screening approach. Approximately 5-7% of routine TVS screening tests yield abnormal results. Some women experience significant distress after receipt of an abnormal TVS screening test. Four focus groups provided in-depth, qualitative data regarding the informational, psychological, and practical needs of women after the receipt of an abnormal TVS result. Through question and content analytic procedures, we identified four themes: anticipation, emotional response, role of the screening technician, and impact of prior cancer experiences. Results provide initial guidance toward development of interventions to promote adaptive responses after receipt of an abnormal cancer screening test result.

  5. Summarising and validating test accuracy results across multiple studies for use in clinical practice.

    Science.gov (United States)

    Riley, Richard D; Ahmed, Ikhlaaq; Debray, Thomas P A; Willis, Brian H; Noordzij, J Pieter; Higgins, Julian P T; Deeks, Jonathan J

    2015-06-15

    Following a meta-analysis of test accuracy studies, the translation of summary results into clinical practice is potentially problematic. The sensitivity, specificity and positive (PPV) and negative (NPV) predictive values of a test may differ substantially from the average meta-analysis findings, because of heterogeneity. Clinicians thus need more guidance: given the meta-analysis, is a test likely to be useful in new populations, and if so, how should test results inform the probability of existing disease (for a diagnostic test) or future adverse outcome (for a prognostic test)? We propose ways to address this. Firstly, following a meta-analysis, we suggest deriving prediction intervals and probability statements about the potential accuracy of a test in a new population. Secondly, we suggest strategies on how clinicians should derive post-test probabilities (PPV and NPV) in a new population based on existing meta-analysis results and propose a cross-validation approach for examining and comparing their calibration performance. Application is made to two clinical examples. In the first example, the joint probability that both sensitivity and specificity will be >80% in a new population is just 0.19, because of a low sensitivity. However, the summary PPV of 0.97 is high and calibrates well in new populations, with a probability of 0.78 that the true PPV will be at least 0.95. In the second example, post-test probabilities calibrate better when tailored to the prevalence in the new population, with cross-validation revealing a probability of 0.97 that the observed NPV will be within 10% of the predicted NPV.

  6. An assessment of consistence of exhaust gas emission test results obtained under controlled NEDC conditions

    Science.gov (United States)

    Balawender, K.; Jaworski, A.; Kuszewski, H.; Lejda, K.; Ustrzycki, A.

    2016-09-01

    Measurements concerning emissions of pollutants contained in automobile combustion engine exhaust gases is of primary importance in view of their harmful impact on the natural environment. This paper presents results of tests aimed at determining exhaust gas pollutant emissions from a passenger car engine obtained under repeatable conditions on a chassis dynamometer. The test set-up was installed in a controlled climate chamber allowing to maintain the temperature conditions within the range from -20°C to +30°C. The analysis covered emissions of such components as CO, CO2, NOx, CH4, THC, and NMHC. The purpose of the study was to assess repeatability of results obtained in a number of tests performed as per NEDC test plan. The study is an introductory stage of a wider research project concerning the effect of climate conditions and fuel type on emission of pollutants contained in exhaust gases generated by automotive vehicles.

  7. Gearbox Reliability Collaborative Phase 1 and 2: Testing and Modeling Results; Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Keller, J.; Guo, Y.; LaCava, W.; Link, H.; McNiff, B.

    2012-05-01

    The Gearbox Reliability Collaborative (GRC) investigates root causes of wind turbine gearbox premature failures and validates design assumptions that affect gearbox reliability using a combined testing and modeling approach. Knowledge gained from the testing and modeling of the GRC gearboxes builds an understanding of how the selected loads and events translate into internal responses of three-point mounted gearboxes. This paper presents some testing and modeling results of the GRC research during Phase 1 and 2. Non-torque loads from the rotor including shaft bending and thrust, traditionally assumed to be uncoupled with gearbox, affect gear and bearing loads and resulting gearbox responses. Bearing clearance increases bearing loads and causes cyclic loading, which could contribute to a reduced bearing life. Including flexibilities of key drivetrain subcomponents is important in order to reproduce the measured gearbox response during the tests using modeling approaches.

  8. A sample-to-result system for blood coagulation tests on a microfluidic disk analyzer.

    Science.gov (United States)

    Lin, Chia-Hui; Liu, Cheng-Yuan; Shih, Chih-Hsin; Lu, Chien-Hsing

    2014-09-01

    In this report, we describe in detail a microfluidic analyzer, which is able to conduct blood coagulation tests using whole blood samples. Sample preparation steps, such as whole blood aliquoting and metering, plasma separation, decanting, and mixing with reagents were performed in sequence through microfluidic functions integrated on a disk. Both prothrombin time (PT) and activated partial thromboplastin time (aPTT) were carried out on the same platform and the test results can be reported in 5 min. Fifty clinical samples were tested for both PT and aPTT utilizing the microfluidic disk analyzer and the instrument used in hospitals. The test results showed good correlation and agreement between the two instruments.

  9. Analysis of Factors Influencing Measurement Accuracy of Al Alloy Tensile Test Results

    Science.gov (United States)

    Podgornik, Bojan; Žužek, Borut; Sedlaček, Marko; Kevorkijan, Varužan; Hostej, Boris

    2016-02-01

    In order to properly use materials in design, a complete understanding of and information on their mechanical properties, such as yield and ultimate tensile strength must be obtained. Furthermore, as the design of automotive parts is constantly pushed toward higher limits, excessive measuring uncertainty can lead to unexpected premature failure of the component, thus requiring reliable determination of material properties with low uncertainty. The aim of the present work was to evaluate the effect of different metrology factors, including the number of tested samples, specimens machining and surface quality, specimens input diameter, type of testing and human error on the tensile test results and measurement uncertainty when performed on 2xxx series Al alloy. Results show that the most significant contribution to measurement uncertainty comes from the number of samples tested, which can even exceed 1 %. Furthermore, moving from experimental laboratory conditions to very intense industrial environment further amplifies measurement uncertainty, where even if using automated systems human error cannot be neglected.

  10. Navigation Doppler Lidar Sensor for Precision Altitude and Vector Velocity Measurements Flight Test Results

    Science.gov (United States)

    Pierrottet, Diego F.; Lockhard, George; Amzajerdian, Farzin; Petway, Larry B.; Barnes, Bruce; Hines, Glenn D.

    2011-01-01

    An all fiber Navigation Doppler Lidar (NDL) system is under development at NASA Langley Research Center (LaRC) for precision descent and landing applications on planetary bodies. The sensor produces high resolution line of sight range, altitude above ground, ground relative attitude, and high precision velocity vector measurements. Previous helicopter flight test results demonstrated the NDL measurement concepts, including measurement precision, accuracies, and operational range. This paper discusses the results obtained from a recent campaign to test the improved sensor hardware, and various signal processing algorithms applicable to real-time processing. The NDL was mounted in an instrumentation pod aboard an Erickson Air-Crane helicopter and flown over vegetation free terrain. The sensor was one of several sensors tested in this field test by NASA?s Autonomous Landing and Hazard Avoidance Technology (ALHAT) project.

  11. First test beam results of prototype modules for the upgrade of the ATLAS strip tracking detector

    CERN Document Server

    Kuehn, Susanne; The ATLAS collaboration

    2016-01-01

    The LHC is foreseen to be upgraded to the High-Luminosity LHC (HL-LHC). This will result in higher particle rates and radiation doses. The ATLAS experiment plans to replace its inner tracking detector by a new all-silicon tracker which is based on the concept of modularity. For the new silicon strip tracker a large prototyping and evaluation campaign is ongoing. Many modules of different types were built and tested both in the laboratories and in test beams. In the following first results obtained in test beams are presented. Both mini and full-size modules for the central and forward regions were tested before and after irradiation to fluences as expected at the HL-LHC.

  12. A research program to reduce interior noise in general aviation airplanes. [test methods and results

    Science.gov (United States)

    Roskam, J.; Muirhead, V. U.; Smith, H. W.; Peschier, T. D.; Durenberger, D.; Vandam, K.; Shu, T. C.

    1977-01-01

    Analytical and semi-empirical methods for determining the transmission of sound through isolated panels and predicting panel transmission loss are described. Test results presented include the influence of plate stiffness and mass and the effects of pressurization and vibration damping materials on sound transmission characteristics. Measured and predicted results are presented in tables and graphs.

  13. Astronomy Diagnostic Test Results Reflect Course Goals and Show Room for Improvement

    Science.gov (United States)

    LoPresto, Michael C.

    2007-01-01

    The results of administering the Astronomy Diagnostic Test (ADT) to introductory astronomy students at Henry Ford Community College over three years have shown gains comparable with national averages. Results have also accurately corresponded to course goals, showing greater gains in topics covered in more detail, and lower gains in topics covered…

  14. The impact of discussing exercise test results of young asthmatic children on adherence to maintenance medication

    NARCIS (Netherlands)

    Visser, R.; Brusse-Keizer, M.; Palen, van der J.; Klok, T.; Thio, B.J.

    2015-01-01

    Objective: Parents’ awareness of their child’s asthma may improve by discussing an exercise challenge test (ECT) result with them. We investigated the influence of discussing an ECT result with parents on adherence to inhaled maintenance medication, parental illness perceptions and medication belief

  15. Interpreting Statistical Significance Test Results: A Proposed New "What If" Method.

    Science.gov (United States)

    Kieffer, Kevin M.; Thompson, Bruce

    As the 1994 publication manual of the American Psychological Association emphasized, "p" values are affected by sample size. As a result, it can be helpful to interpret the results of statistical significant tests in a sample size context by conducting so-called "what if" analyses. However, these methods can be inaccurate…

  16. Spacesuit Portable Life Support System Breadboard (PLSS 1.0) Development and Test Results

    Science.gov (United States)

    Vogel, Matt R.; Watts, Carly

    2011-01-01

    A multi-year effort has been carried out at NASA-JSC to develop an advanced Extravehicular Activity (EVA) PLSS design intended to further the current state of the art by increasing operational flexibility, reducing consumables, and increasing robustness. Previous efforts have focused on modeling and analyzing the advanced PLSS architecture, as well as developing key enabling technologies. Like the current International Space Station (ISS) Extravehicular Mobility Unit (EMU) PLSS, the advanced PLSS comprises of three subsystems required to sustain the crew during EVA including the Thermal, Ventilation, and Oxygen Subsystems. This multi-year effort has culminated in the construction and operation of PLSS 1.0, a test rig that simulates full functionality of the advanced PLSS design. PLSS 1.0 integrates commercial off the shelf hardware with prototype technology development components, including the primary and secondary oxygen regulators, ventilation loop fan, Rapid Cycle Amine (RCA) swingbed, and Spacesuit Water Membrane Evaporator (SWME). Testing accumulated 239 hours over 45 days, while executing 172 test points. Specific PLSS 1.0 test objectives assessed during this testing include: confirming key individual components perform in a system level test as they have performed during component level testing; identifying unexpected system-level interactions; operating PLSS 1.0 in nominal steady-state EVA modes to baseline subsystem performance with respect to metabolic rate, ventilation loop pressure and flow rate, and environmental conditions; simulating nominal transient EVA operational scenarios; simulating contingency EVA operational scenarios; and further evaluating individual technology development components. Successful testing of the PLSS 1.0 provided a large database of test results that characterize system level and component performance. With the exception of several minor anomalies, the PLSS 1.0 test rig performed as expected; furthermore, many system

  17. ASME N510 test results for Savannah River Site AACS filter compartments

    Energy Technology Data Exchange (ETDEWEB)

    Paul, J.D.; Punch, T.M. [Westinghouse Savannah River Company, Aiken, SC (United States)

    1995-02-01

    The K-Reactor at the Savannah River Site recently implemented design improvements for the Airborne Activity Confinement System (AACS) by procuring, installing, and testing new Air Cleaning Units, or filter compartments, to ASME AG-11, N509, and N510 requirements. Specifically, these new units provide documentable seismic resistance to a Design Basis Accident earthquake, provide 2 inch adsorber beds with 0.25 second residence time, and meet all AG-1, N509, and N510 requirements for testability and maintainability. This paper presents the results of the Site acceptance testing and discusses an issue associated with sample manifold qualification testing.

  18. Synopsis of the results of ISP-39 on FARO test L-14

    Energy Technology Data Exchange (ETDEWEB)

    Addabbo, C.; Annunziato, A.; Magallon, D. [Commission of the European Communities, Ispra (Italy). Joint Research Center

    1998-01-01

    This paper provides a synopsis of the salient results from the ISP(International Standard Problem)-39 exercise promoted by OECD-CSNI in the frame of the NEA activities aimed at fostering international cooperation in reactor safety research and development. ISP-39 has been conceived to benchmark the predictive capabilities of computer codes used in the evaluation of FCI and quenching phenomenologies of relevance in water cooled reactors severe accidents safety analysis. The ISP-39 reference case is FARO test L-14, a non-energetic FCI test performed in the FARO experimental installation under realistic melt composition and prototypical test conditions. (author)

  19. Results of data base management system parameterized performance testing related to GSFC scientific applications

    Science.gov (United States)

    Carchedi, C. H.; Gough, T. L.; Huston, H. A.

    1983-01-01

    The results of a variety of tests designed to demonstrate and evaluate the performance of several commercially available data base management system (DBMS) products compatible with the Digital Equipment Corporation VAX 11/780 computer system are summarized. The tests were performed on the INGRES, ORACLE, and SEED DBMS products employing applications that were similar to scientific applications under development by NASA. The objectives of this testing included determining the strength and weaknesses of the candidate systems, performance trade-offs of various design alternatives and the impact of some installation and environmental (computer related) influences.

  20. Results and Consequences of Magnet Test and Cosmic Challenge of the CMS Barrel Muon Alignment System

    CERN Document Server

    Bencze, Gy L; Imrek, J; Molnàr, J; Novàk, D; Raics, P; Sass, V; Szabò, Zs; Svékely, G; Szillàsi, Z; PH-EP

    2007-01-01

    In the last year - as part of the first test of the CMS experiment at CERN [1] called Magnet Test and Cosmic Challenge (MTCC) - about 25% of the barrel muon position monitoring system was built and operated. The configuration enabled us to test all the elements of the system and its function in real conditions. The correct operation of the system has been demonstrated. About 500 full measurement cycles have been recorded. In the paper the setup –including the read-out and control - is described and the first preliminary results are presented.

  1. Addendum to Guarantee Testing Results from the Greenidge Multi-Pollutant Control Project: Additiona NH3, NOx, and CO Testing Results

    Energy Technology Data Exchange (ETDEWEB)

    Connell, Daniel P; Locke, James E

    2008-03-01

    On March 28-30 and May 1-4, 2007, CONSOL Energy Inc. Research & Development (CONSOL R&D) performed flue gas sampling at AES Greenidge to verify the performance of the multi-pollutant control system recently installed by Babcock Power Environmental Inc. (BPEI) on the 107-MW Unit 4 (Boiler 6). The multi-pollutant control system includes combustion modifications and a hybrid selective non-catalytic reduction (SNCR)/in-duct selective catalytic reduction (SCR) system to reduce NO{sub x} emissions, followed by a Turbosorp{reg_sign} circulating fluidized bed dry scrubber system and baghouse to reduce emissions of SO{sub 2}, SO{sub 3}, HCl, HF, and particulate matter. Mercury removal is provided via the co-benefits afforded by the in-duct SCR, dry scrubber, and baghouse and by injection of activated carbon upstream of the scrubber, as required. The testing in March and May demonstrated that the multi-pollutant control system attained its performance targets for NO{sub x} emissions, SO{sub 2} removal efficiency, acid gas (SO{sub 3}, HCl, and HF) removal efficiency, and mercury removal efficiency. However, the ammonia slip measured between the SCR outlet and air heater inlet was consistently greater than the guarantee of 2 ppmvd {at} 3% O{sub 2}. As a result, additional testing was performed on May 30-June 1 and on June 20-21, 2007, in conjunction with tuning of the hybrid NO{sub x} control system by BPEI, in an effort to achieve the performance target for ammonia slip. This additional testing occurred after the installation of a large particle ash (LPA) screen and removal system just above the SCR reactor and a fresh SCR catalyst layer in mid-May. This report describes the results of the additional tests. During the May 30-June 1 sampling period, CONSOL R&D and Clean Air Engineering (CAE) each measured flue gas ammonia concentrations at the air heater inlet, downstream of the in-duct SCR reactor. In addition, CONSOL R&D measured flue gas ammonia concentrations at the

  2. Fatigue Failure Results for Multi-Axial versus Uniaxial Stress Screen Vibration Testing

    Directory of Open Access Journals (Sweden)

    Wayne E. Whiteman

    2002-01-01

    Full Text Available To date, the failure potential and prediction between simultaneous multi-axial versus sequentially applied uniaxial vibration stress screen testing has been the subject of great debate. In most applications, current vibration tests are done by sequentially applying uniaxial excitation to the test specimen along three orthogonal axes. The most common standards for testing military equipment are published in MIL-STD-810F and NAVMAT P-9492. Previous research had shown that uniaxial testing may be unrealistic and inadequate. This current research effort is a continuing effort to systematically investigate the differences between fatigue damage mechanisms and the effects of uniaxial versus tri-axial testing. This includes assessing the ability of the tri-axial method in predicting the formation of damage mechanisms, specifically looking at the effects of stress or fatigue failure. Multi-axial testing achieves the synergistic effect of exciting all modes simultaneously and induces a more realistic vibration stress loading condition. As such, it better approximates real-world operating conditions. This paper provides the latest results on the differences between multi-axial and uniaxial testing of a simple notched cantilever beam.

  3. Test results on re-use of reclaimed shower water: Summary. [space stations

    Science.gov (United States)

    Verostko, C. E.; Garcia, R.; Sauer, R.; Linton, A. T.; Elms, T.; Reysa, R. P.

    1988-01-01

    A microgravity whole body shower (WBS) and waste water recovery systems (WWRS) were evaluated in three separate closed loop tests. Following a protocol similar to that anticipated for the U.S. Space Station, test subjects showered in a prototype whole body shower. The WWRS processes evaluated during the test series were phase change and reverse osmosis (RO). A preprototype Thermoelectric Integrated Hollow Fiber Membrane Evaporation Subsystem phase change process was used for the initial test with chemical pretreatment of the shower water waste input. The second and third tests concentrated on RO technologies. The second test evaluated a dynamic RO membrane consisting of zirconium oxide polyacrylic acid (ZOPA) membranes deposited on the interior diameter of 316L porous stainless steel tubes while the final test employed a thin semipermeable RO membrane deposited on the interior surface of polysulfone hollow fibers. All reclaimed water was post-treated for purity using ion exchange and granular activated carbon beds immediately followed by microbial control treatment using both heat and iodine. The test hardware, controls exercised for whole body showering, types of soaps evaluated, shower subject response to reclaimed water showering, and shower water collection and chemical pretreatment (if required) for microbial control are described. The WWRS recovered water performance and the effectiveness of the reclaimed water post-treatment techniques used for maintaining water purity and microorganism control are compared. Results on chemical and microbial impurity content of the water samples obtained from various locations in the shower water reuse system are summarized.

  4. Evaluation of photopatch test allergens for Indian patients of photodermatitis: Preliminary results

    Directory of Open Access Journals (Sweden)

    Nidhi Jindal

    2011-01-01

    Full Text Available Background: There is a strong need to develop a photopatch test tray suitable for Indian patients of photodermatitis as European/Scandinavian photopatch test trays may not be wholly relevant for them. Aim: We carried out this study using photoallergens relevant in the Indian context to determine their relevance in patients of photodermatitis. Methods: Thirty patients (M:F, 23:7 between 19 and 76 years of age of photodermatitis and 10 controls were patch- and photopatch tested with 20 common photoallergens. In addition, the patients were also (photo patch tested with articles of daily use as and when these were suspected to be the cause. Results: Forty-three positive reactions to one or more antigens were seen in 22 (74% patients. Fourteen positive photopatch tests to seven allergens were observed in 10 (33% patients, and nine (30% of them had a definite relevance. The most common contact allergen was fragrance mix (FM (30%, followed by p-phenylenediamine (20% and Parthenium hysterophorous (17%. The definite relevance of the patch- and photopatch tests could be correlated in 47% of these patients. Conclusions: FM is the most common contact and photocontact allergen among the various photopatch test antigens. Although differences in technique and evaluation make direct comparison between different centers difficult, still photopatch testing remains an integral part and gold standard for the work-up of the photosensitive patients.

  5. Beam test results of the irradiated Silicon Drift Detector for ALICE

    CERN Document Server

    Kushpil, S; Giubellino, P.; Idzik, M.; Kolozhvari, A.; Kushpil, V.; Martinez, M.I.; Mazza, G.; Mazzoni, A.; Meddi, F.; Nouais, D.; Petracek, V.; Piemonte, C.; Rashevsky, A.; Riccati, L.; Rivetti, A.; Tosello, F.; Vacchi, A.; Wheadon, R.

    2006-01-01

    The Silicon Drift Detectors will equip two of the six cylindrical layers of high precision position sensitive detectors in the ITS of the ALICE experiment at LHC. In this paper we report the beam test results of a SDD irradiated with 1 GeV electrons. The aim of this test was to verify the radiation tolerance of the device under an electron fluence equivalent to twice particle fluence expected during 10 years of ALICE operation.

  6. Influence of Specimen Preparation and Test Methods on the Flexural Strength Results of Monolithic Zirconia Materials

    OpenAIRE

    Christine Schatz; Monika Strickstrock; Malgorzata Roos; Daniel Edelhoff; Marlis Eichberger; Isabella-Maria Zylla; Bogna Stawarczyk

    2016-01-01

    The aim of this work was to evaluate the influence of specimen preparation and test method on the flexural strength results of monolithic zirconia. Different monolithic zirconia materials (Ceramill Zolid (Amann Girrbach, Koblach, Austria), Zenostar ZrTranslucent (Wieland Dental, Pforzheim, Germany), and DD Bio zx2 (Dental Direkt, Spenge, Germany)) were tested with three different methods: 3-point, 4-point, and biaxial flexural strength. Additionally, different specimen preparation methods wer...

  7. Influence of specimen preparation and test methods on the flexural strength results of monolithic zirconia materials

    OpenAIRE

    Schatz, Christine; Strickstrock, Monika; Roos, Malgorzata; Edelhoff, Daniel; Eichberger, Marlis; Zylla, Isabella-Maria; Stawarczyk, Bogna

    2016-01-01

    The aim of this work was to evaluate the influence of specimen preparation and test method on the flexural strength results of monolithic zirconia. Different monolithic zirconia materials (Ceramill Zolid (Amann Girrbach, Koblach, Austria), Zenostar ZrTranslucent (Wieland Dental, Pforzheim, Germany), and DD Bio zx2 (Dental Direkt, Spenge, Germany)) were tested with three different methods: 3-point, 4-point, and biaxial flexural strength. Additionally, different specimen preparation methods wer...

  8. Results of SC proton cavity tests (B = 1 and B = 0.65)

    CERN Document Server

    Peauger, F et al

    2013-01-01

    The two superconducting cavities were carefully designed for challenging performance. They were fabricated in industry with intermediate tests and specialized processing in CEA and CNRS. The results are promising, except for a degradation of the field flatness of the low velocity cavity, after electron-beam welding. This might reduce the accelerating gradient. Due to delays in manufacturing, the final performance tests will be carried out in the coming months.

  9. Results of Laboratory and Industrial Tests of Periodic-Type Gas Generators

    Science.gov (United States)

    Karp, I. N.; P‧yanykh, K. E.; Antoshchuk, T. A.; Lysenko, A. A.

    2015-05-01

    Results of laboratory and industrial tests of periodic-type gas generators burning various solid biofuels have been presented. The tests were carried out with the aim of obtaining producer gas which could totally or partly replace natural gas in power equipment burning gaseous fuel. The energy and environmental characteristics of a boiler unit burning a mixture of producer gas and natural gas have been assessed.

  10. A multigroup radiation diffusion test problem: Comparison of code results with analytic solution

    Energy Technology Data Exchange (ETDEWEB)

    Shestakov, A I; Harte, J A; Bolstad, J H; Offner, S R

    2006-12-21

    We consider a 1D, slab-symmetric test problem for the multigroup radiation diffusion and matter energy balance equations. The test simulates diffusion of energy from a hot central region. Opacities vary with the cube of the frequency and radiation emission is given by a Wien spectrum. We compare results from two LLNL codes, Raptor and Lasnex, with tabular data that define the analytic solution.

  11. Flight testing of the AIM/RIM-7M missile, preflight analysis

    Science.gov (United States)

    Hicks, W.; Greenberg, E.

    1981-11-01

    The AIM/RIM-7M missile is the most recent version of the AIM-7 missile series. It is in the preproduction phase and has completed most of the preproduction flight test evaluation. A description is presented of the preflight simulation techniques used, taking into account the value of the techniques in predicting the results of actual flights. The AIM/RIM-7M is a semiactive, radar-guided homing missile with sophisticated onboard digital processing. It may be launched from either an aircraft or a surface system. To a large degree, the AIM/RIM-7M represents problems typical of all guided missiles. The described techniques are directly applicable to radar-guided missiles and generically to all types of guided missiles. Attention is given to simulation bay activities, the anechoic chamber, aspects of RF control, the target array, computer models, aspects of preflight simulations, and the test setup.

  12. A Persian version of the sustained auditory attention capacity test and its results in normal children

    Directory of Open Access Journals (Sweden)

    Sanaz Soltanparast

    2013-03-01

    Full Text Available Background and Aim: Sustained attention refers to the ability to maintain attention in target stimuli over a sustained period of time. This study was conducted to develop a Persian version of the sustained auditory attention capacity test and to study its results in normal children.Methods: To develop the Persian version of the sustained auditory attention capacity test, like the original version, speech stimuli were used. The speech stimuli consisted of one hundred monosyllabic words consisting of a 20 times random of and repetition of the words of a 21-word list of monosyllabic words, which were randomly grouped together. The test was carried out at comfortable hearing level using binaural, and diotic presentation modes on 46 normal children of 7 to 11 years of age of both gender.Results: There was a significant difference between age, and an average of impulsiveness error score (p=0.004 and total score of sustained auditory attention capacity test (p=0.005. No significant difference was revealed between age, and an average of inattention error score and attention reduction span index. Gender did not have a significant impact on various indicators of the test.Conclusion: The results of this test on a group of normal hearing children confirmed its ability to measure sustained auditory attention capacity through speech stimuli.

  13. Scaling Relationships Based on Scaled Tank Mixing and Transfer Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Piepel, Gregory F.; Holmes, Aimee E.; Heredia-Langner, Alejandro; Lee, Kearn P.; Kelly, Steven E.

    2014-01-01

    This report documents the statistical analyses performed (by Pacific Northwest National Laboratory for Washington River Protection Solutions) on data from 26 tests conducted using two scaled tanks (43 and 120 inches) in the Small Scale Mixing Demonstration platform. The 26 tests varied several test parameters, including mixer-jet nozzle velocity, base simulant, supernatant viscosity, and capture velocity. For each test, samples were taken pre-transfer and during five batch transfers. The samples were analyzed for the concentrations (lbs/gal slurry) of four primary components in the base simulants (gibbsite, stainless steel, sand, and ZrO2). The statistical analyses including modeling the component concentrations as functions of test parameters using stepwise regression with two different model forms. The resulting models were used in an equivalent performance approach to calculate values of scaling exponents (for a simple geometric scaling relationship) as functions of the parameters in the component concentration models. The resulting models and scaling exponents are displayed in tables and graphically. The sensitivities of component concentrations and scaling exponents to the test parameters are presented graphically. These results will serve as inputs to subsequent work by other researchers to develop scaling relationships that are applicable to full-scale tanks.

  14. Scaling Relationships Based on Scaled Tank Mixing and Transfer Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Piepel, Gregory F.; Holmes, Aimee E.; Heredia-Langner, Alejandro

    2013-09-18

    This report documents the statistical analyses performed (by Pacific Northwest National Laboratory for Washington River Protection Solutions) on data from 26 tests conducted using two scaled tanks (43 and 120 inches) in the Small Scale Mixing Demonstration platform. The 26 tests varied several test parameters, including mixer-jet nozzle velocity, base simulant, supernatant viscosity, and capture velocity. For each test, samples were taken pre-transfer and during five batch transfers. The samples were analyzed for the concentrations (lbs/gal slurry) of four primary components in the base simulants (gibbsite, stainless steel, sand, and ZrO2). The statistical analyses including modeling the component concentrations as functions of test parameters using stepwise regression with two different model forms. The resulting models were used in an equivalent performance approach to calculate values of scaling exponents (for a simple geometric scaling relationship) as functions of the parameters in the component concentration models. The resulting models and scaling exponents are displayed in tables and graphically. The sensitivities of component concentrations and scaling exponents to the test parameters are presented graphically. These results will serve as inputs to subsequent work by other researchers to develop scaling relationships that are applicable to full-scale tanks.

  15. Small-Scale Water Ingression and Crust Strength Tests (SSWICS) SSWICS-6 test data report : thermal hydraulic results, Rev. 0.

    Energy Technology Data Exchange (ETDEWEB)

    Lomperski, S.; Farmer, M. T.; Kilsdonk, D.; Aeschlimann, B. (Nuclear Engineering Division)

    2011-06-28

    The Melt Attack and Coolability Experiments (MACE) program at Argonne National Laboratory addressed the issue of the ability of water to cool and thermally stabilize a molten core/concrete interaction (MCCI) when the reactants are flooded from above. These tests provided data regarding the nature of corium interactions with concrete, the heat transfer rates from the melt to the overlying water pool, and the role of noncondensable gases in the mixing processes that contribute to melt quenching. However, due to the integral nature of these tests, several questions regarding the crust freezing behavior could not be adequately resolved. These questions include: (1) To what extent does water ingression into the crust increase the melt quench rate above the conduction-limited rate and how is this affected by melt composition and system pressure? (2) What is the fracture strength of the corium crust when subjected to a thermal-mechanical load and how does it depend upon the melt composition? A series of separate-effects experiments are being conducted to address these issues. The first employs an apparatus designed to measure the quench rate of a pool of corium ({approx} {phi} 30 cm; up to 20 cm deep). The main parameter to be varied in these quench tests is the melt composition since it is thought to have a critical influence on the crust cracking behavior which, in turn, alters quench rate. The issue of crust strength is being addressed with a second apparatus designed to mechanically load the crust produced by the quench tests. This apparatus measures the fracture strength of the crust while it is either at room temperature or above, the latter state being achieved with a heating element placed below the crust. The two apparatuses used to measure the melt quench rate and crust strength are jointly referred to as SSWICS (Small-Scale Water Ingression and Crust Strength). This report describes results of the sixth water ingression test, designated SSWICS-6. This test

  16. Emotion self-regulation, psychophysiological coherence, and test anxiety: results from an experiment using electrophysiological measures.

    Science.gov (United States)

    Bradley, Raymond Trevor; McCraty, Rollin; Atkinson, Mike; Tomasino, Dana; Daugherty, Alane; Arguelles, Lourdes

    2010-12-01

    This study investigated the effects of a novel, classroom-based emotion self-regulation program (TestEdge) on measures of test anxiety, socioemotional function, test performance, and heart rate variability (HRV) in high school students. The program teaches students how to self-generate a specific psychophysiological state--psychophysiological coherence--which has been shown to improve nervous system function, emotional stability, and cognitive performance. Implemented as part of a larger study investigating the population of tenth grade students in two California high schools (N = 980), the research reported here was conducted as a controlled pre- and post-intervention laboratory experiment, using electrophysiological measures, on a random stratified sample of students from the intervention and control schools (N = 136). The Stroop color-word conflict test was used as the experiment's stimulus to simulate the stress of taking a high-stakes test, while continuous HRV recordings were gathered. The post-intervention electrophysiological results showed a pattern of improvement across all HRV measures, indicating that students who received the intervention program had learned how to better manage their emotions and to self-activate the psychophysiological coherence state under stressful conditions. Moreover, students with high test anxiety exhibited increased HRV and heart rhythm coherence even during a resting baseline condition (without conscious use of the program's techniques), suggesting that they had internalized the benefits of the intervention. Consistent with these results, students exhibited reduced test anxiety and reduced negative affect after the intervention. Finally, there is suggestive evidence from a matched-pairs analysis that reduced test anxiety and increased psychophysiological coherence appear to be directly associated with improved test performance--a finding consistent with evidence from the larger study.

  17. High Fidelity Thermal Simulators for Non-Nuclear Testing: Analysis and Initial Results

    Science.gov (United States)

    Bragg-Sitton, Shannon M.; Dickens, Ricky; Dixon, David

    2007-01-01

    Non-nuclear testing can be a valuable tool in the development of a space nuclear power system, providing system characterization data and allowing one to work through various fabrication, assembly and integration issues without the cost and time associated with a full ground nuclear test. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Testing with non-optimized heater elements allows one to assess thermal, heat transfer, and stress related attributes of a given system, but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. High fidelity thermal simulators that match both the static and the dynamic fuel pin performance that would be observed in an operating, fueled nuclear reactor can vastly increase the value of non-nuclear test results. With optimized simulators, the integration of thermal hydraulic hardware tests with simulated neutronie response provides a bridge between electrically heated testing and fueled nuclear testing, providing a better assessment of system integration issues, characterization of integrated system response times and response characteristics, and assessment of potential design improvements' at a relatively small fiscal investment. Initial conceptual thermal simulator designs are determined by simple one-dimensional analysis at a single axial location and at steady state conditions; feasible concepts are then input into a detailed three-dimensional model for comparison to expected fuel pin performance. Static and dynamic fuel pin performance for a proposed reactor design is determined using SINDA/FLUINT thermal analysis software, and comparison is made between the expected nuclear performance and the performance of conceptual thermal simulator designs. Through a series of iterative analyses, a conceptual high fidelity design can developed. Test results presented in this paper correspond to a "first cut" simulator design for a potential

  18. Some results of a simulated test for administration of activity in nuclear medicine

    Energy Technology Data Exchange (ETDEWEB)

    Oropesa, P. [Centro de Isotopos (CENTIS), San Jose de las Lajas, Habana (Cuba)]. E-mail: poropesa@centis.edu.cu; Hernandez, A.T. [Centro de Isotopos (CENTIS), San Jose de las Lajas, Habana (Cuba); Serra, R.A. [Centro de Isotopos (CENTIS), San Jose de las Lajas, Habana (Cuba); Varela, C. [Centro de Control Estatal de Equipos Medicos (CCEEM). Havana (Cuba); Woods, M.J. [Ionising Radiation Metrology Consultants Ltd, Teddington (United Kingdom)

    2006-04-15

    This paper describes the results obtained using a simulated test for administration of activity in nuclear medicine between 2002 and 2004. Measurements in the radionuclide calibrator are made during the different stages of the procedure. The test attempts to obtain supplementary information on the quality of the measurement, with the aim of evaluating in a more complete way the accuracy of the administered activity value compared with the prescribed one. The participants' performance has been assessed by means of a statistical analysis of the reported data. Dependences between several attributes of the simulated administration tests results are discussed. Specifically, the proportion of satisfactory results in the 2003-2004 period was found to be higher than in 2002. It reveals an improvement of the activity administration in the Cuban nuclear medicine departments since 2003.

  19. Test Results From The Idaho National Laboratory Of The NASA Bi-Supported Cell Design

    Energy Technology Data Exchange (ETDEWEB)

    C Stoots; J O' Brien; T Cable

    2009-11-01

    The Idaho National Laboratory has been researching the application of solid-oxide fuel cell technology for large-scale hydrogen production. As a result, the Idaho National Laboratory has been testing various cell designs to characterize electrolytic performance. NASA, in conjunction with the University of Toledo, has developed a new cell concept with the goals of reduced weight and high power density. This paper presents results of the INL's testing of this new solid oxide cell design as an electrolyzer. Gas composition, operating voltage, and other parameters were varied during testing. Results to date show the NASA cell to be a promising design for both high power-to-weight fuel cell and electrolyzer applications.

  20. Spacesuit Portable Life Support System Breadboard (PLSS 1.0) Development and Test Results

    Science.gov (United States)

    Watts, Carly A.; Vogel, Matt

    2012-01-01

    A multi-year effort has been carried out at the Johnson Space Center to develop an advanced EVA PLSS design intended to further the current state of the art by increasing operational flexibility, reducing consumables, and increasing robustness. This multi-year effort has culminated in the construction and operation of PLSS 1.0, a test rig that simulates full functionality of the advanced PLSS design. PLSS 1.0 integrates commercial off-the-shelf hardware with prototype technology development components, including the primary and secondary oxygen regulators, ventilation loop fan, Rapid Cycle Amine (RCA) swingbed, and Spacesuit Water Membrane Evaporator (SWME). PLSS 1.0 was tested from June 17th through September 30th, 2011. Testing accumulated 233 hours over 45 days, while executing 119 test points. An additional 164 hours of operational time were accrued during the test series, bringing the total operational time for PLSS 1.0 testing to 397 hours. Specific PLSS 1.0 test objectives assessed during this testing include: (1) Confirming prototype components perform in a system level test as they have performed during component level testing, (2) Identifying unexpected system-level interactions (3) Operating PLSS 1.0 in nominal steady-state EVA modes to baseline subsystem performance with respect to metabolic rate, ventilation loop pressure and flow rate, and environmental conditions (4) Simulating nominal transient EVA operational scenarios (5) Simulating contingency EVA operational scenarios (6) Further evaluating prototype technology development components Successful testing of the PLSS 1.0 provided a large database of test results that characterize system level and component performance. With the exception of several minor anomalies, the PLSS 1.0 test rig performed as expected. Documented anomalies and observations include: (1) Ventilation loop fan controller issues at high fan speeds (near 70,000 rpm, whereas the fan speed during nominal operations would be closer

  1. Comparison of the results of T-Test from different versions of Epi Info

    Institute of Scientific and Technical Information of China (English)

    Junke Tang; Jinliang Zhu

    2005-01-01

    Objective: To take advantage of Epi Info to manage and analyze disease data. Methods: After selecting the living examples for independent sample T-Test, Epi Info 5.00, 5.01a(Chinese), 6.00, 6.04 b, 6.04 d, 2000, 2002(Chinese)were used to do the independent sample T-Test on the two living examples. Then, Intercooled Stata7, Microsoft Excel(2002) and SPSS 10.0 for Windows were used to verify the results. Results: The statistical results from the Epi Info 5.00, 5.01a(Chinese) and 6.00 were the same while that from Epi Info 6.04 b, 6.04 d, 2000,2002 (Chinese), Intercooled Stata7, Microsoft Excel(2002) and SPSS 10.0 for Windows were identical In independent sample T-Test,. But the former result is different with the latter. Conclusion: There was an error in the result of T-Test from Epi Info 6.00 and former versions. Thus, it's important to be alert to select the versions of Epi Info to manage and analyze disease data. On the other hand, it's also quite pivotal to distinguish the adopted Epi Info versions when referring to the articles ane use the statistical results.

  2. Effect of Acupressure on Non-stress Test (NST Results: A Randomized-Controlled Trial Study

    Directory of Open Access Journals (Sweden)

    Masoume Pirhadi

    2015-10-01

    Full Text Available BackgroundPregnancy and delivery are among the most stressful events in women’s life . Breech presentation is defined as a fetus in a longitudinal lie with the buttocks or feet closest to the cervix. This occurs in 3-4% of all deliveries.The risk for perinatal mortality was 1 in 300 for planned breech deliveries.Some conventional non-surgical therapies for breech presentation are available. acupoint (BL67 stimulations are commonly used for the correction of breech presentation. The present study aimed to evaluate the effect of acupressure on fetal wellbeing test results.MethodThis study is a clinical trialthat was conducted in one group and the two-steps.Participantswere pregnant women (primigravida who were 35 to 18 years that refer to Shahid Beheshti hospital in Isfahan in 2013 to receive routine prenatal care.The 32 pregnant women (32-36 weeks were randomly selected.They were stimulated immediately after the first Non stress test and before the second test.The researchers’ evaluated and analyzed variables using SPSS software version 20.FindingsMean (SD age of the subjects was 24/7±2/8 and 93/8% of them was housekeeper. The frequency of reactive Non Stress Test (NST was same before and after stimulation. The mean time of the tests’ result was decreased after stimulation significantly ( p-value=0.048. ConclusionsAlthough fetal non-stress test result wasn’t influenced by acupressure but this intervention led to shorter testing time to achieve results. In other words, after the intervention, the time it takes to reach a reactive fetal non-stress test is about 2/7 minutes less than the time without intervention.

  3. Risk factors for false positive and for false negative test results in screening with fecal occult blood testing.

    Science.gov (United States)

    Stegeman, Inge; de Wijkerslooth, Thomas R; Stoop, Esther M; van Leerdam, Monique; van Ballegooijen, M; Kraaijenhagen, Roderik A; Fockens, Paul; Kuipers, Ernst J; Dekker, Evelien; Bossuyt, Patrick M

    2013-11-15

    Differences in the risk of a false negative or a false positive fecal immunochemical test (FIT) across subgroups may affect optimal screening strategies. We evaluate whether subgroups are at increased risk of a false positive or a false negative FIT result, whether such variability in risk is related to differences in FIT sensitivity and specificity or to differences in prior CRC risk. Randomly selected, asymptomatic individuals were invited to undergo colonoscopy. Participants were asked to undergo one sample FIT and to complete a risk questionnaire. We identified patient characteristics associated with a false negative and false positive FIT results using logistic regression. We focused on statistically significant differences as well as on variables influencing the false positive or negative risk for which the odds ratio exceeded 1.25. Of the 1,426 screening participants, 1,112 (78%) completed FIT and the questionnaire; 101 (9.1%) had advanced neoplasia. 102 Individuals were FIT positive, 65 (64%) had a false negative FIT result and 66 (65%) a false positive FIT result. Participants at higher age and smokers had a significantly higher risk of a false negative FIT result. Males were at increased risk of a false positive result, so were smokers and regular NSAID users. FIT sensitivity was lower in females. Specificity was lower for males, smokers and regular NSAID users. FIT sensitivity was lower in women. FIT specificity was lower in males, smokers and regular NSAID users. Our results can be used for further evidence based individualization of screening strategies.

  4. Monomethylhydrazine versus hydrazine fuels - Test results using a 100 pound thrust bipropellant rocket engine

    Science.gov (United States)

    Smith, J. A.; Stechman, R. C.

    1981-01-01

    A test program was performed to evaluate hydrazine (N2H4) as a fuel for a 445 Newton (100 lbf) thrust bipropellant rocket engine. Results of testing with an identical thruster utilizing monomethylhydrazine (MMH) are included for comparison. Engine performance with hydrazine fuel was essentially identical to that experienced with monomethylhydrazine although higher combustor wall temperatures (approximately 400 F) were obtained with hydrazine. Results are presented which indicate that hydrazine as a fuel is compatible with Marquardt bipropellant rocket engines which use monomethylhydrazine as a baseline fuel.

  5. An Analysis Of Tensile Test Results to Assess the Innovation Risk for an Additive Manufacturing Technology

    Directory of Open Access Journals (Sweden)

    Adamczak Stanisław

    2015-03-01

    Full Text Available The aim of this study was to assess the innovation risk for an additive manufacturing process. The analysis was based on the results of static tensile tests obtained for specimens made of photocured resin. The assessment involved analyzing the measurement uncertainty by applying the FMEA method. The structure of the causes and effects of the discrepancies was illustrated using the Ishikawa diagram. The risk priority numbers were calculated. The uncertainty of the tensile test measurement was determined for three printing orientations. The results suggest that the material used to fabricate the tensile specimens shows clear anisotropy of the properties in relation to the printing direction.

  6. Follow-up of abnormal or inadequate test results in the Danish Cervical Cancer Screening Program

    DEFF Research Database (Denmark)

    Kristiansen, Bettina Kjær

    2014-01-01

    -up recommendation. However problems with delayed follow-up may threaten the effectiveness of the Danish Cervical Cancer Screening Program, as 20% of women are delayed and dysplasia potentially can progress into cancer. Delayed follow-up is found in situations where women either consciously or unconsciously postpone...... follow-up, or because of organizational aspects of the screening program, where communication regarding test results can fail either in content or with delay.This study will evaluate two interventions designed to increase follow-up: 1) A letter with the test result and potential recommendation for follow...

  7. Results of Investigative Tests of Gas Turbine Engine Compressor Blades Obtained by Electrochemical Machining

    Science.gov (United States)

    Kozhina, T. D.; Kurochkin, A. V.

    2016-04-01

    The paper highlights results of the investigative tests of GTE compressor Ti-alloy blades obtained by the method of electrochemical machining with oscillating tool-electrodes, carried out in order to define the optimal parameters of the ECM process providing attainment of specified blade quality parameters given in the design documentation, while providing maximal performance. The new technological methods suggested based on the results of the tests; in particular application of vibrating tool-electrodes and employment of locating elements made of high-strength materials, significantly extend the capabilities of this method.

  8. Performance of Charcoal Cookstoves for Haiti Part 1: Results from the Water Boiling Test

    Energy Technology Data Exchange (ETDEWEB)

    Booker, Kayje; Han, Tae Won; Granderson, Jessica; Jones, Jennifer; Lsk, Kathleen; Yang, Nina; Gadgil, Ashok

    2011-06-01

    In April 2010, a team of scientists and engineers from Lawrence Berkeley National Lab (LBNL) and UC Berkeley, with support from the Darfur Stoves Project (DSP), undertook a fact-finding mission to Haiti in order to assess needs and opportunities for cookstove intervention. Based on data collected from informal interviews with Haitians and NGOs, the team, Scott Sadlon, Robert Cheng, and Kayje Booker, identified and recommended stove testing and comparison as a high priority need that could be filled by LBNL. In response to that recommendation, five charcoal stoves were tested at the LBNL stove testing facility using a modified form of version 3 of the Shell Foundation Household Energy Project Water Boiling Test (WBT). The original protocol is available online. Stoves were tested for time to boil, thermal efficiency, specific fuel consumption, and emissions of CO, CO{sub 2}, and the ratio of CO/CO{sub 2}. In addition, Haitian user feedback and field observations over a subset of the stoves were combined with the experiences of the laboratory testing technicians to evaluate the usability of the stoves and their appropriateness for Haitian cooking. The laboratory results from emissions and efficiency testing and conclusions regarding usability of the stoves are presented in this report.

  9. Overseas testing of a multisensor landmine detection system: results and lessons learned

    Science.gov (United States)

    Keranen, Joe G.; Topolosky, Zeke

    2009-05-01

    The Nemesis detection system has been developed to provide an efficient and reliable unmanned, multi-sensor, groundbased platform to detect and mark landmines. The detection system consists of two detection sensor arrays: a Ground Penetrating Synthetic Aperture Radar (GPSAR) developed by Planning Systems, Inc. (PSI) and an electromagnetic induction (EMI) sensor array developed by Minelab Electronics, PTY. Limited. Under direction of the Night Vision and Electronic Sensors Directorate (NVESD), overseas testing was performed at Kampong Chhnang Test Center (KCTC), Cambodia, from May 12-30, 2008. Test objectives included: evaluation of detection performance, demonstration of real-time visualization and alarm generation, and evaluation of system operational efficiency. Testing was performed on five sensor test lanes, each consisting of a unique soil mixture and three off-road lanes which include curves, overgrowth, potholes, and non-uniform lane geometry. In this paper, we outline the test objectives, procedures, results, and lessons learned from overseas testing. We also describe the current state of the system, and plans for future enhancements and modifications including clutter rejection and feature-level fusion.

  10. Test results of the 18 kA EDIPO HTS current leads

    Energy Technology Data Exchange (ETDEWEB)

    Wesche, Rainer, E-mail: rainer.wesche@psi.ch [Ecole Polytechnique Federale de Lausanne (EPFL), Centre de Recherches en Physique des Plasmas (CRPP), Association Euratom - Confederation Suisse, 5232 Villigen PSI (Switzerland); Bagnasco, Maurizio; Bruzzone, Pierluigi; Felder, Roland; Guetg, Marc; Holenstein, Manuel; Jenni, Markus; March, Stephen; Roth, Felix; Vogel, Martin [Ecole Polytechnique Federale de Lausanne (EPFL), Centre de Recherches en Physique des Plasmas (CRPP), Association Euratom - Confederation Suisse, 5232 Villigen PSI (Switzerland)

    2011-10-15

    For the new test facility EDIPO (European DIPOle), to be hosted by CRPP, two 18 kA HTS current leads were manufactured and successfully tested. The HTS module, made of AgMgAu/Bi-2223 tapes, is cooled only by heat conduction to the cold end, while the copper part is cooled by forced flow helium gas. The current leads were tested at low voltage up to the maximum current of 18 kA. The helium mass flow rates required for stable operation at various currents were determined. In addition to the steady state operation, the transient behavior in the case of a loss of flow was studied experimentally. The test results provide an estimate of the operational limits of the EDIPO HTS current leads.

  11. First Total Reflection X-Ray Fluorescence round-robin test of water samples: Preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Borgese, Laura; Bilo, Fabjola [Chemistry for Technologies Laboratory, University of Brescia, Brescia (Italy); Tsuji, Kouichi [Graduate School of Engineering, Osaka City University, Osaka (Japan); Fernández-Ruiz, Ramón [Servicio Interdepartamental de Investigación (SIdI), Laboratorio de TXRF, Universidad Autónoma de Madrid, Madrid (Spain); Margui, Eva [Department of Chemistry, University of Girona, Girona (Spain); Streli, Christina [TU Wien, Atominstitut,Radiation Physics, Vienna (Austria); Pepponi, Giancarlo [Fondazione Bruno Kessler, Povo, Trento (Italy); Stosnach, Hagen [Bruker Nano GmbH, Berlin (Germany); Yamada, Takashi [Rigaku Corporation, Takatsuki, Osaka (Japan); Vandenabeele, Peter [Department of Archaeology, Ghent University, Ghent (Belgium); Maina, David M.; Gatari, Michael [Institute of Nuclear Science and Technology, University of Nairobi, Nairobi (Kenya); Shepherd, Keith D.; Towett, Erick K. [World Agroforestry Centre (ICRAF), Nairobi (Kenya); Bennun, Leonardo [Laboratorio de Física Aplicada, Departamento de Física, Universidad de Concepción (Chile); Custo, Graciela; Vasquez, Cristina [Gerencia Química, Laboratorio B025, Centro Atómico Constituyentes, San Martín (Argentina); Depero, Laura E., E-mail: laura.depero@unibs.it [Chemistry for Technologies Laboratory, University of Brescia, Brescia (Italy)

    2014-11-01

    Total Reflection X-Ray Fluorescence (TXRF) is a mature technique to evaluate quantitatively the elemental composition of liquid samples deposited on clean and well polished reflectors. In this paper the results of the first worldwide TXRF round-robin test of water samples, involving 18 laboratories in 10 countries are presented and discussed. The test was performed within the framework of the VAMAS project, interlaboratory comparison of TXRF spectroscopy for environmental analysis, whose aim is to develop guidelines and a standard methodology for biological and environmental analysis by means of the TXRF analytical technique. - Highlights: • The discussion of the first worldwide TXRF round-robin test of water samples (18 laboratories of 10 countries) is reported. • Drinking, waste, and desalinated water samples were tested. • Data dispersion sources were identified: sample concentration, preparation, fitting procedure, and quantification. • The protocol for TXRF analysis of drinking water is proposed.

  12. Wind Tunnel and Hover Performance Test Results for Multicopter UAS Vehicles

    Science.gov (United States)

    Russell, Carl R.; Jung, Jaewoo; Willink, Gina; Glasner, Brett

    2016-01-01

    There is currently a lack of published data for the performance of multicopter unmanned aircraft system (UAS) vehicles, such as quadcopters and octocopters, often referred to collectively as drones. With the rapidly increasing popularity of multicopter UAS, there is interest in better characterizing the performance of this type of aircraft. By studying the performance of currently available vehicles, it will be possible to develop models for vehicles at this scale that can accurately predict performance and model trajectories. This paper describes a wind tunnel test that was recently performed in the U.S. Army's 7- by 10-ft Wind Tunnel at NASA Ames Research Center. During this wind tunnel entry, five multicopter UAS vehicles were tested to determine forces and moments as well as electrical power as a function of wind speed, rotor speed, and vehicle attitude. The test is described here in detail, and a selection of the key results from the test is presented.

  13. Patch-test results in children and adolescents: systematic review of a 15-year period.

    Science.gov (United States)

    Rodrigues, Dulcilea Ferraz; Goulart, Eugênio Marcos Andrade

    2016-01-01

    The number of studies on patch-test results in children and adolescents has gradually increased in recent years, thus stimulating reviews. This paper is a systematic review of a 15-year period devoted to studying the issue. Variations pertaining to the number and age groups of tested children and/or adolescents, the number of subjects with atopy/atopic dermatitis history, the quantity, type and concentrations of the tested substances, the test technique and type of data regarding clinical relevance, must all be considered in evaluating these studies, as they make it harder to formulate conclusions. The most common allergens in children were nickel, thimerosal, cobalt, fragrance, lanolin and neomycin. In adolescents, they were nickel, thimerosal, cobalt, fragrance, potassium dichromate, and Myroxylon pereirae. Knowledge of this matter aids health professionals in planning preventive programs aimed at improving children's quality of life and ensuring that their future prospects are not undermined.

  14. Results of Performance Tests Performed on the John Watts Casing Connection on 7" Pipe

    Energy Technology Data Exchange (ETDEWEB)

    John D. Watts

    1999-08-01

    reviewing the results, it was believed that several conditions may have contributed to the premature leaks: The BOL 2000 thread lubricant contains solid particles that are larger than the solid particles in API 5A2 compound. Possibly the large particles prevented tight thread contact necessary for gas leak tightness. The BOL 2000 lubricant may have caused or at least contributed to the yielding of the pin end during makeup. Pin inward deformation was found in some pins subsequent to testing and breakout. Excessive yielding of the pin or box will contribute to poor thread contact and leakage. The connections were made up to full or near full shoulder contact. This causes the end of the pin to be stressed near the yield strength. This along with the interference caused by the thread compound may cause excessive pin hoop stresses and yielding which in turn gives relatively loose thread contact. This behavior is present when repeated makeup and breakout occurs.

  15. First test results of a high-speed beam conditions monitor for the ATLAS experiment

    CERN Document Server

    Pernegger, Heinz

    2004-01-01

    The paper presents the design and first test results of the high- speed beam conditions monitor (BCM) for the ATLAS experiment at the large hadron collider (LHC). The goal of the BCM is to monitor instantaneous rates of collision and background and detect signs of beam instabilities. The detector is based on polycrystalline chemical-vapor-deposition (pCVD) diamond as active sensor material. We have chosen this detector material for its proven radiation hardness and fast signal properties. For the readout of the diamonds we developed front-end readout electronics based on high-bandwidth RF amplifiers. The signal response of the amplifier has been optimized for the ionization current signal of pCVD diamond in order to achieve a signal risetime of test results which were obtained on prototype assemblies in source tests and test beam. The obtained results demonstrate the feasibility of such a detector system for the ATLAS BCM. The tests yield BCM signals w...

  16. RESEARCH ABOUT RESULTS REPRODUTIBILITY AND ABRASIVE PARTICLES FRAGMENTATION IN BALL-CRATERING TESTS

    Directory of Open Access Journals (Sweden)

    Ronaldo Câmara Cozza

    2013-06-01

    Full Text Available The micro-abrasive wear tests by rotating ball (crater wear have played an important role in abrasive wear researches. In this type of test, the contact between a specimen and a ball on rotating motion and abrasive particles supplied between these two elements, results in a crater on the specimen, based on which the abrasive wear behaviour is analysed. The purpose of this work is to study results the reprodutibility and the silicon carbide (SiC abrasive particles fragmentation during micro-abrasive wear tests. Tests were conducted with carburized AISI 1010 steel balls and high speed steel specimens, “with” and “without” titanium nitride (TiN coatings. The abrasive slurry was prepared with black silicon carbide (average particle size of 5 µm and distilled water. Grooving abrasion is related with lower reprodutibility results. For the test conditions of this work, no abrasive particles fragmentation was observed, independently of the sliding distance, what is justified, among others factors, by the low normal force applied.

  17. Bioventing pilot test results at the low point drain area, Offutt AFB, Nebraska.

    Science.gov (United States)

    Werner, F T; Walters, J E; Keefer, G B

    1997-11-21

    The purpose of this paper was to describe the application of bioventing technology at the LPD site at Offutt AFB, Nebraska and present the results of the 15-month pilot test. The preliminary tests indicated sufficient hydrocarbon contamination was present with the necessary soil characteristics to warrant an extended bioventing pilot test. The six month in situ respiration test indicated that progress was being made in reducing the TVH concentrations and biological activity was still occurring. Laboratory analysis of the final soil samples confirmed the reduction in TRPH and BTEX concentrations indicating that the site is close to complete remediation. However, owing to reduced air flow at greater distances from the VW, more biodegradation is still needed near MPB. The reduced biodegradation at MPB could also be due to the high water tables resulting from heavy rains during the summer and fall of 1993. The local water table was above the VW and MP screens for several months. The operation of the blower will continue until the site is completely remediated. The single VW pilot test at the LPD site at Offutt AFB has proven the effectiveness of bioventing in reducing TRPH and BTEX contamination in the subsurface. The installation, operation and maintenance costs were minimal. The effectiveness of this application has resulted in three additional bioventing applications at Offutt AFB including the first, full-scale system located in the state of Nebraska.

  18. Ground test results and analysis advancements for the AFRL airborne CO2 DIAL system

    Science.gov (United States)

    Senft, Daniel C.; Fox, Marsha J.; Hamilton, Carla M.; Richter, Dale A.; Higdon, N. S.; Kelly, Brian T.; Babnick, Robert D.; Pierrottet, Diego F.

    1999-10-01

    The Air Force Research Laboratory (AFRL) Active Remote Sensing Branch has developed the Laser Airborne Remote Sensing (LARS) system for chemical detection using the differential absorption lidar technique. The system is based on a high-power CO2 laser which can use either the standard 12C16O2 or the 13C16O2 carbon dioxide isotopes as the lasing medium, and has output energies of up to 5 J on the stronger laser transitions. The lidar system is mounted on a flight-qualified optical breadboard designed for installation into the AFRL Argus C- 135E optical testbed aircraft. The Phase I ground tests were conducted at Kirtland AFB in 1997, prior to the LARS flight tests performed in September 1997 at Kirtland AFB and the Idaho National Engineering and Environmental Laboratory. The Phase II ground tests were conducted in 1998 to determine the optimum performance of the LARS systems, after the incorporation of modifications and improvements suggested by the flight test results. This paper will present some of the chemical detection and radiometric results obtained during the Phase II ground tests. Following the presentation of the direct detection results, a summary of current work on a heterodyne DIAL system is given.

  19. Space-based LH 2 propellant storage system: subscale ground testing results

    Science.gov (United States)

    Liggett, M. W.

    An orbital cryogenic liquid storage facility will be one of the essential elements of the US Space Program to realize the benefits of space-based cryogenic propulsion vehicles such as NASA's space transfer vehicle (STV) for transporting personnel and scientific packages from a space station in low earth orbit (LEO) to geosynchronous orbit (GEO), the moon and beyond. Long-term thermal control of LH 2 and LO 2 storage cryotanks is a key technical objective for many NASA and SDI programmes. Improved retention using refrigeration, boil-off vapour-cooled shields (VCSs), multilayer superinsulation (MLI) and para-ortho (P-O) hydrogen conversion are the required state-of-the-art techniques. The cryotank system level development testing (CSLDT) programme has supported the development of these technologies. Under the programme, trade studies and analyses were followed by the design and construction of a subscale LH 2 storage facility test article for steady-state and transient thermal tests. A two-stage gaseous helium (GHe) refrigerator was integrated with the test article and used to reduce boil-off and/or decrease the time required between passive test configuration steady-state conditions. The LH 2 tank, mounted in a vacuum chamber, was thermally shielded from the chamber wall by MLI blankets and two VCSs. The VCSs were cooled with either LH 2 boil-off gas (through an optional P-O converter) or refrigerated GHe. The CSLDT test article design, assembly and results from 400 hours of thermal tests are presented along with important conclusions. A comparison of predicted and measured steady-state boil-off rates is provided for 10 test configurations, and the system time constant is addressed. Also presented are some of the unique issues and challenges encountered during these tests that are related to instrumentation and control.

  20. Experimental results from pressure testing a 1:6-scale nuclear power plant containment

    Energy Technology Data Exchange (ETDEWEB)

    Horschel, D.S. [Sandia National Labs., Albuquerque, NM (United States)

    1992-01-01

    This report discusses the testing of a 1:6-scale, reinforced-concrete containment building at Sandia National Laboratories, in Albuquerque, New Mexico. The scale-model, Light Water Reactor (LWR) containment building was designed and built to the American Society of Mechanical Engineers (ASME) code by United Engineers and Constructors, Inc., and was instrumented with over 1200 transducers to prepare for the test. The containment model was tested to failure to determine its response to static internal overpressurization. As part of the US Nuclear Regulatory Commission`s program on containment integrity, the test results will be used to assess the capability of analytical methods to predict the performance of containments under severe-accident loads. The scaled dimensions of the cylindrical wall and hemispherical dome were typical of a full-size containment. Other typical features included in the heavily reinforced model were equipment hatches, personnel air locks, several small piping penetrations, and a ihin steel liner that was attached to the concrete by headed studs. In addition to the transducers attached to the model, an acoustic detection system and several video and still cameras were used during testing to gather data and to aid in the conduct of the test. The model and its instrumentation are briefly discussed, and is followed by the testing procedures and measured response of the containment model. A summary discussion is included to aid in understanding the significance of the test as it applies to real world reinforced concrete containment structures. The data gathered during SIT and overpressure testing are included as an appendix.

  1. Testing and Results of Human Metabolic Simulation Utilizing Ultrasonic Nebulizer Technology for Water Vapor Generation

    Science.gov (United States)

    Stubbe, Matthew; Curley, Su

    2010-01-01

    Life support technology must be evaluated thoroughly before ever being implemented into a functioning design. A major concern during that evaluation is safety. The ability to mimic human metabolic loads allows test engineers to evaluate the effectiveness of new technologies without risking injury to any actual humans. The main function of most life support technologies is the removal of carbon dioxide (CO2) and water (H2O) vapor. As such any good human metabolic simulator (HMS) will mimic the human body s ability to produce these items. Introducing CO2 into a test chamber is a very straightforward process with few unknowns so the focus of this particular new HMS design was on the much more complicated process of introducing known quantities of H2O vapor on command. Past iterations of the HMS have utilized steam which is very hard to keep in vapor phase while transporting and injecting into a test chamber. Also steam adds large quantities of heat to any test chamber, well beyond what an actual human does. For the new HMS an alternative approach to water vapor generation was designed utilizing ultrasonic nebulizers as a method for creating water vapor. Ultrasonic technology allows water to be vibrated into extremely tiny pieces (2-5 microns) and evaporate without requiring additional heating. Doing this process inside the test chamber itself allows H2O vapor generation without the unwanted heat and the challenging process of transporting water vapor. This paper presents the design details as well as results of all initial and final acceptance system testing. Testing of the system was performed at a range of known human metabolic rates in both sea-level and reduced pressure environments. This multitude of test points fully defines the systems capabilities as they relate to actual environmental systems testing.

  2. Results of Performance Tests Performed on the John Watts Casing Connection on 7" Pipe

    Energy Technology Data Exchange (ETDEWEB)

    John D. Watts

    1999-08-01

    Stress Engineering Services (SES) was contracted by Mr. John Watts to test his threaded connection developed for oilfield oil and gas service. This particular test required the application of a variety of loads including axial tension and compression, internal pressure (gas), external pressure (water), bending and both low and elevated temperature. These loads were used to determine the sealing and structural limits of the connection. The connection design tested had tapered threads with 10 threads per inch. A square thread form and a round thread form were tested. The square thread form had a 2{sup o} load flank and 15{sup o} stab flank. The round thread had a 0{sup o} load flank and 20{sup o} stab flank. Most of the testing was performed on the round thread form. Both a coupled connection design and an integral connection design were tested. The coupling was a pin by pin (male) thread, with the pipe having a box (female) thread. Both designs have outside and inside diameters that are flush with the pipe body. Both designs also contain a small external shoulder. The test procedure selected for this evaluation was the newly written ISO 13679 procedure for full scale testing of casing and tubing connections. The ISO procedure requires a variety of tests that includes makeup/breakout testing, internal gas sealability/external water sealability testing with axial tension, axial compression, bending, internal gas thermal cycle tests and limit load (failure) tests. This test was performed with four coupled samples and included most of these loads. Two integral samples were also included for limit load testing ISO makeup/breakout tests are divided into three types--initial makeup, IML1, repeated makeup within the same sample, MBL, and repeated makeup using several samples called round robin, RR. IMU and MBL were performed in this project. The ISO sealing and structural procedure is divided into four primary tests and identified as Series A, B, C and Limit Load (failure

  3. Natural Frequencies Do Not Foster Public Understanding of Medical Test Results.

    Science.gov (United States)

    Pighin, Stefania; Gonzalez, Michel; Savadori, Lucia; Girotto, Vittorio

    2016-08-01

    Major organizations recommend presenting medical test results in terms of natural frequencies, rather than single-event probabilities. The evidence, however, is that natural frequency presentations benefit at most one-fifth of samples of health service users and patients. Only one study reported a substantial benefit of these presentations. Here, we replicate that study, testing online survey respondents. Study 1 attributed the previously reported benefit of natural frequencies to a scoring artifact. Study 2 showed that natural frequencies may elicit evaluations that conflict with the normatively correct one, potentially hindering informed decision making. Ironically, these evaluations occurred less often when respondents reasoned about single-event probabilities. These results suggest caution in promoting natural frequencies as the best way to communicate medical test data to health service users and patients.

  4. A Visual Basic program for analyzing oedometer test results and evaluating intergranular void ratio

    Science.gov (United States)

    Monkul, M. Murat; Önal, Okan

    2006-06-01

    A visual basic program (POCI) is proposed and explained in order to analyze oedometer test results. Oedometer test results have vital importance from geotechnical point of view, since settlement requirements usually control the design of foundations. The software POCI is developed in order perform the necessary calculations for convential oedometer test. The change of global void ratio and stress-strain characteristics can be observed both numerically and graphically. It enables the users to calculate some parameters such as coefficient of consolidation, compression index, recompression index, and preconsolidation pressure depending on the type and stress history of the soil. Moreover, it adopts the concept of intergranular void ratio which may be important especially in the compression behavior of sandy soils. POCI shows the variation of intergranular void ratio and also enables the users to calculate granular compression index.

  5. The Influence of Instrumented Striker Configuration on the Results of Dynamic Toughness Testing

    Energy Technology Data Exchange (ETDEWEB)

    Lucon, E.

    2008-09-15

    Several studies are available on the influence of the edge radius of instrumented strikers (ASTM - 8 mm or ISO - 2 mm) on the results of both non instrumented and instrumented Charpy tests. This paper investigates the effect of using either a 2 mm or a 8 mm striker when performing dynamic toughness tests at impact loading rates on precracked Charpy specimens. Existing data from tests run in the ductile-to-brittle region (dynamic Master Curve reference temperature) and in the upper shelf regime (ductile initiation fracture toughness and crack resistance curves) have been analyzed. The results show that 2 mm strikers tend to yield lower cleavage fracture toughness in the transition region (although the effect cannot be considered statistically significant), whereas the influence of striker configuration is negligible in the upper shelf regime when data are generated using the low-blow multiple-specimen technique.

  6. Real world experience with antiphospholipid antibody tests : how stable are results over time?

    NARCIS (Netherlands)

    Erkan, D; Derksen, WJM; Kaplan, [No Value; Sammaritano, L; Pierangeli, SS; Roubey, R; Lockshin, MD

    2005-01-01

    Objective: To determine the stability and the degree of variation of antiphospholipid antibody (aPL) results over time in a large cohort of well evaluated aPL positive patients; and to analyse factors contributing to aPL variation and the validity of aPL in a real world setting in which aPL tests ar

  7. 77 FR 37717 - Electrical Cable Test Results and Analysis During Fire Exposure

    Science.gov (United States)

    2012-06-22

    ... Commission. ACTION: Draft NUREG; request for comment. SUMMARY: The U.S. Nuclear Regulatory Commission (NRC or the Commission) is making the proposed draft, NUREG-2128, ``Electrical Cable Test Results and Analysis... available in ADAMS) is provided the first time that a document is referenced. The proposed draft...

  8. NIPTRIC : an online tool for clinical interpretation of non-invasive prenatal testing (NIPT) results

    NARCIS (Netherlands)

    Sikkema-Raddatz, Birgit; Johansson, Lennart F; de Boer, Eddy N; Boon, Elles M J; Suijkerbuijk, Ron F; Bouman, Katelijne; Bilardo, Catia M; Swertz, Morris A; Dijkstra, Martijn; van Langen, Irene M; Sinke, Richard J; Te Meerman, Gerard J

    2016-01-01

    To properly interpret the result of a pregnant woman's non-invasive prenatal test (NIPT), her a priori risk must be taken into account in order to obtain her personalised a posteriori risk (PPR), which more accurately expresses her true likelihood of carrying a foetus with trisomy. Our aim was to de

  9. Results from the beam test of the engineering model of the GLAST large area telescope

    Energy Technology Data Exchange (ETDEWEB)

    Couto e Silva, E. do E-mail: eduardo@slac.stanford.edu; Anthony, P.; Arnold, R.; Arrighi, H.; Bloom, E.; Baughman, B.; Bogart, J.; Bosted, P.; Bumala, B.; Chekhtman, A.; Cotton, N.; Crider, A.; Dobbs-Dixon, I.; Djannati-Atai, A.; Dubois, R.; Engovatov, D.; Espigat, P.; Evans, J.L.; Fieguth, T.; Flath, D.; Frigaard, M.; Giebels, B.; Gillespie, S.; Godfrey, G.; Grove, J.E.; Handa, T.; Hansl-Kozanecka, T.; Hernando, J.; Hicks, M.; Hirayama, M.; Johnson, W.N.; Johnson, R.; Kamae, T.; Kroeger, W.; Lauben, D.; Lin, Y.C.; Lindner, T.; Michelson, P.; Moiseev, A.; Nikolaou, M.; Nolan, P.; Odian, A.; Ohsugi, T.; Ormes, J.; Paliaga, G.; Parkinson, P. Saz; Phlips, B.; Ritz, S.; Rock, S.; Russel, J.J.; Sadrozinski, H.; Schalk, T.; Silvis, J.; Szalata, Z.; Terrier, R.; Thompson, D.J.; Tournear, D.M.; Waite, A.P.; Wallace, J.; Williams, S.; Williamson, R.; Winker, G

    2001-11-21

    This paper describes the results of a beam test using the Engineering Model of the GLAST Large Area Telescope, which was installed in a beam of positrons, hadrons and tagged photons at SLAC. The performance of the four subsystems, Anti Coincidence Detector, Silicon Tracker, Calorimeter and Data Acquisition will be described.

  10. Results of metallographical diagnostic examination of Navy half-watt thermoelectric converters degraded by accelerated tests

    Science.gov (United States)

    Rosell, F. E., Jr.; Rouklove, P. G.

    1977-01-01

    To verify the 15-year reliability of the Navy half-watt radioisotope thermoelectric generator (RTG), bismuth-telluride thermoelectric converters were submitted to testing at high temperatures which accelerated the degradation and caused failure of the converters. Metallographic diagnostic examination of failed units verified failure mechanisms. Results of diagnostic examinations are presented.

  11. Preliminary results of the round-robin testing of F82H

    Energy Technology Data Exchange (ETDEWEB)

    Shiba, K.; Yamanouchi, N.; Tohyama, A.

    1996-10-01

    Preliminary results of metallurgical, physical and mechanical properties of low activation ferritic steel F82H (IEA heat) were obtained in the round-robin test in Japan. The properties of IEA heat F82H were almost the same as the original F82H.

  12. 77 FR 15101 - Results From Inert Ingredient Test Orders Issued Under EPA's Endocrine Disruptor Screening...

    Science.gov (United States)

    2012-03-14

    ..., Endocrine disruptors, Pesticides and pests. Dated: February 17, 2012. Lois Rossi, Director, Registration... AGENCY Results From Inert Ingredient Test Orders Issued Under EPA's Endocrine Disruptor Screening Program... EPA's Endocrine Disruptor Screening Program (EDSP) and the Federal Food, Drug, and Cosmetic Act...

  13. Beam test results of the BTeV silicon pixel detector

    CERN Document Server

    Appel, J A

    2001-01-01

    We report the results of the BTeV silicon pixel detector tests carried out in the MTest beam at Fermilab in 1999-2000. The pixel detector spatial resolution has been studied as a function of track inclination, sensor bias, and readout threshold.

  14. What do women think about abnormal smear test results? A qualitative interview study.

    NARCIS (Netherlands)

    Lagro-Janssen, A.L.M.; Schijf, C.P.T.

    2005-01-01

    The aim of the study is a report of Dutch women's views on abnormal cervical smear test results and the consequences thereof. Twenty-seven women with recent PAP III in their history were interviewed in the context of this qualitative study. GPs often do not inform patients beforehand about the ways

  15. Effect of simultaneous consolidation and creep on interpretation of test results

    DEFF Research Database (Denmark)

    Krogsbøll, Anette Susanne

    2003-01-01

    A constitutive model describing the combined process of simultaneous consolidation and creep is used to evaluate the practical significance of time effects on iterpretation of test results and also on settlements in field. The constitutive model includes elastic strains, viscoplastic strains...

  16. General Atomic reprocessing pilot plant: description and results of initial testing

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    In June 1976 General Atomic completed the construction of a reprocessing head-end cold pilot plant. In the year since then, each system within the head end has been used for experiments which have qualified the designs. This report describes the equipment in the plant and summarizes the results of the initial phase of reprocessing testing.

  17. 40 CFR 205.57-5 - Reporting of the test results.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Reporting of the test results. 205.57-5 Section 205.57-5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks §...

  18. Preliminary results of a proficiency testing of industrial CT scanners using small polymer items

    DEFF Research Database (Denmark)

    Angel, Jais Andreas Breusch; Cantatore, Angela; De Chiffre, Leonardo

    2012-01-01

    This work presents preliminary results concerning a proficiency testing for intercomparison of industrial CT scanners. Two audit items, similar to common industrial parts, were selected for circulation. The two items were a single polymer complex geometry part and a simple geometry item made of two...

  19. Performance and Environmental Test Results of the High Voltage Hall Accelerator Engineering Development Unit

    Science.gov (United States)

    Kamhawi, Hani; Haag, Thomas; Huang, Wensheng; Shastry, Rohit; Pinero, Luis; Peterson, Todd; Mathers, Alex

    2012-01-01

    NASA Science Mission Directorate's In-Space Propulsion Technology Program is sponsoring the development of a 3.5 kW-class engineering development unit Hall thruster for implementation in NASA science and exploration missions. NASA Glenn and Aerojet are developing a high fidelity high voltage Hall accelerator that can achieve specific impulse magnitudes greater than 2,700 seconds and xenon throughput capability in excess of 300 kilograms. Performance, plume mappings, thermal characterization, and vibration tests of the high voltage Hall accelerator engineering development unit have been performed. Performance test results indicated that at 3.9 kW the thruster achieved a total thrust efficiency and specific impulse of 58%, and 2,700 sec, respectively. Thermal characterization tests indicated that the thruster component temperatures were within the prescribed material maximum operating temperature limits during full power thruster operation. Finally, thruster vibration tests indicated that the thruster survived the 3-axes qualification full-level random vibration test series. Pre and post-vibration test performance mappings indicated almost identical thruster performance. Finally, an update on the development progress of a power processing unit and a xenon feed system is provided.

  20. Results of the Regional Earthquake Likelihood Models (RELM) test of earthquake forecasts in California.

    Science.gov (United States)

    Lee, Ya-Ting; Turcotte, Donald L; Holliday, James R; Sachs, Michael K; Rundle, John B; Chen, Chien-Chih; Tiampo, Kristy F

    2011-10-04

    The Regional Earthquake Likelihood Models (RELM) test of earthquake forecasts in California was the first competitive evaluation of forecasts of future earthquake occurrence. Participants submitted expected probabilities of occurrence of M ≥ 4.95 earthquakes in 0.1° × 0.1° cells for the period 1 January 1, 2006, to December 31, 2010. Probabilities were submitted for 7,682 cells in California and adjacent regions. During this period, 31 M ≥ 4.95 earthquakes occurred in the test region. These earthquakes occurred in 22 test cells. This seismic activity was dominated by earthquakes associated with the M = 7.2, April 4, 2010, El Mayor-Cucapah earthquake in northern Mexico. This earthquake occurred in the test region, and 16 of the other 30 earthquakes in the test region could be associated with it. Nine complete forecasts were submitted by six participants. In this paper, we present the forecasts in a way that allows the reader to evaluate which forecast is the most "successful" in terms of the locations of future earthquakes. We conclude that the RELM test was a success and suggest ways in which the results can be used to improve future forecasts.

  1. Water tunnel results of leading-edge vortex flap tests on a delta wing vehicle

    Science.gov (United States)

    Delfrate, J. H.

    1986-01-01

    A water tunnel flow visualization test on leading edge vortex flaps was conducted at the flow visualization facility of the NASA Ames Research Center's Dryden Flight Research Facility. The purpose of the test was to visually examine the vortex structures caused by various leading edge vortex flaps on the delta wing of an F-106 model. The vortex flaps tested were designed analytically and empirically at the NASA Langley Research Center. The three flap designs were designated as full-span gothic flap, full-span untapered flap, and part-span flap. The test was conducted at a Reynolds number of 76,000/m (25,000/ft). This low Reynolds number was used because of the 0.076-m/s (0.25-ft/s) test section flow speed necessary for high quality flow visualization. However, this low Reynolds number may have influenced the results. Of the three vortex flaps tested, the part-span flap produced what appeared to be the strongest vortex structure over the flap area. The full-span gothic flap provided the next best performance.

  2. Results of long-term field tests of protective earthing device for vessel electric systems

    OpenAIRE

    Blaginin V.A.; Kazhekin I.E.; Yusyp V.M.; Moskalyuk A.M.; Syrenko D.P.

    2015-01-01

    The results of prolonged natural tests of protective neutral earthing device for controlling the fire and electrical safety of vessel electric systems have been shown. The use of such devices provides safe single-phase fault currents and reducing arc overvoltage during the long-term operation of a ship. The results of long-term monitoring of the device operation as part of the existing vessel electric power system have confirmed its effectiveness

  3. Results of long-term field tests of protective earthing device for vessel electric systems

    Directory of Open Access Journals (Sweden)

    Blaginin V.A.

    2015-03-01

    Full Text Available The results of prolonged natural tests of protective neutral earthing device for controlling the fire and electrical safety of vessel electric systems have been shown. The use of such devices provides safe single-phase fault currents and reducing arc overvoltage during the long-term operation of a ship. The results of long-term monitoring of the device operation as part of the existing vessel electric power system have confirmed its effectiveness

  4. Results from the 1997 run of the LHCb ring imaging Cherenkov test-beam

    CERN Document Server

    Halley, A; Teixeira-Dias, P; Wilkinson, G; Wilkinson, Guy

    1998-01-01

    Analysis results of data from the ring imaging Cherenkov test-beam using hybrid photo diodes are presented. Details are given of the geometrical arrangement of the prototype and data-taking conditions, together with results of simulation and studies of the detector performance, photon yield and Cherenkov angle resolution using different radiators. Good agreement with simulation is found for both gas and aerogel photon yield calculations and the observed Cherenkov angle resolution.1

  5. Air Monitoring Network at Tonopah Test Range: Network Description, Capabilities, and Analytical Results

    Energy Technology Data Exchange (ETDEWEB)

    Hartwell, William T.; Daniels, Jeffrey; Nikolich, George; Shadel, Craig; Giles, Ken; Karr, Lynn; Kluesner, Tammy

    2012-01-01

    During the period April to June 2008, at the behest of the Department of Energy (DOE), National Nuclear Security Administration, Nevada Site Office (NNSA/NSO); the Desert Research Institute (DRI) constructed and deployed two portable environmental monitoring stations at the Tonopah Test Range (TTR) as part of the Environmental Restoration Project Soils Activity. DRI has operated these stations since that time. A third station was deployed in the period May to September 2011. The TTR is located within the northwest corner of the Nevada Test and Training Range (NTTR), and covers an area of approximately 725.20 km2 (280 mi2). The primary objective of the monitoring stations is to evaluate whether and under what conditions there is wind transport of radiological contaminants from Soils Corrective Action Units (CAUs) associated with Operation Roller Coaster on TTR. Operation Roller Coaster was a series of tests, conducted in 1963, designed to examine the stability and dispersal of plutonium in storage and transportation accidents. These tests did not result in any nuclear explosive yield. However, the tests did result in the dispersal of plutonium and contamination of surface soils in the surrounding area.

  6. Results from phase 2 of the radioiodine test facility experimental program

    Energy Technology Data Exchange (ETDEWEB)

    Ball, J.M.; Kupferschmid, W.C.H.; Wren, J.C. [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs.

    1996-12-01

    A series of intermediate-scale experiments were conducted in the Radioiodine Test Facility (RTF) in a vinyl-painted, zinc-primer coated, carbon steel vessel in order to assess the effects of vinyl surfaces on iodine volatility in both the presence and absence of radiation. This test series, Phase 2 of a larger, comprehensive program assessing a variety of containment surfaces, also examined the effects of organic (i.e., methyl ethyl ketone) and inorganic (i.e., hydrazine) additives, pH, and venting on the aqueous chemistry and volatility of solutions initially containing cesium iodide. These tests have clearly demonstrated that organics are released to the aqueous phase from the vinyl coating and that, under radiation conditions, these organics can have a significant effect on the formation of volatile iodine species. In particular, the RTF results suggest that radiolytic decomposition of the released organics results in dramatic reductions in pH and dissolved oxygen concentration, which in turn are responsible for increased formation of molecular iodine and organic iodides. When the pH was maintained at 10 (Test 3), much lower iodine volatility was observed; low iodine volatility was also observed in the absence of radiation. This test series also demonstrated that vinyl surfaces, particularly those in contact with the gas phase, were a sink for iodine. (author) 4 figs., 6 tabs., 17 refs.

  7. Correlations between visual test results and flying performance on the advanced simulator for pilot training (ASPT).

    Science.gov (United States)

    Kruk, R; Regan, D; Beverley, K I; Longridge, T

    1981-08-01

    Looking for visual differences in pilots to account for differences in flying performance, we tested five groups of subjects: Air Force primary student jet pilots, graduating (T38 aircraft) students, Air Force pilot instructors, and two control groups made up of experienced nonpilot aircrew and nonflying civilians. This interim report compares 13 different visual test results with low-visibility landing performance on the Air Force Human Resources Laboratory ASPT simulator. Performance was assessed by the number of crashes and by the distance of the aircraft from the runway threshold at the time of the first visual flight correction. Our main finding was that, for student pilots, landing performance correlated with tracking performance for a target that changed size (as if moving in depth) and also with tracking performance for a target that moved sideways. On the other hand, landing performance correlated comparatively weakly with psychophysical thresholds for motion and contrast. For student pilots, several of the visual tests gave results that correlated with flying grades in T37 and T38 jet aircraft. Tracking tests clearly distinguished between the nonflying group and all the flying groups. On the other hand, visual threshold tests did not distinguish between nonflying and flying groups except for grating contrast, which distinguished between the nonflying group and the pilot instructors. The sideways-motion tracking task was sensitive enough to distinguish between the various flying groups.

  8. Carbon dioxide removal system for closed loop atmosphere revitalization, candidate sorbents screening and test results

    Science.gov (United States)

    Mattox, E. M.; Knox, J. C.; Bardot, D. M.

    2013-05-01

    Due to the difficulty and expense it costs to resupply manned-spacecraft habitats, a goal is to create a closed loop atmosphere revitalization system, in which precious commodities such as oxygen, carbon dioxide, and water are continuously recycled. Our aim is to test other sorbents for their capacity for future spacecraft missions, such as on the Orion spacecraft, or possibly lunar or Mars mission habitats to see if they would be better than the zeolite sorbents on the 4-bed molecular sieve. Some of the materials being tested are currently used for other industry applications. Studying these sorbents for their specific spacecraft application is different from that for applications on earth because in space, there are certain power, mass, and volume limitations that are not as critical on Earth. In manned-spaceflight missions, the sorbents are exposed to a much lower volume fraction of CO2 (0.6% volume CO2) than on Earth. LiLSX was tested for its CO2 capacity in an atmosphere like that of the ISS. Breakthrough tests were run to establish the capacities of these materials at a partial pressure of CO2 that is seen on the ISS. This paper discusses experimental results from benchmark materials, such as results previously obtained from tests on Grade 522, and the forementioned candidate materials for the Carbon Dioxide Removal Assembly (CDRA) system.

  9. The relationships between the performance test results of young crossbred boars

    Directory of Open Access Journals (Sweden)

    Jerzy NOWACHOWICZ

    2012-09-01

    Full Text Available The relationships between the most important results of performance test of 3.876 young crossbred boars, expressed as calculated correlation coefficients were determined. The animals came from 6 crossing variants: Hampshire x Belgian Landrace (H x BL, Hampshire x Duroc (H x D, Hampshire x Pietrain (H x P, Duroc x Pietrain (D x P, Pietrain x Hampshire (P x H and Pietrain x Duroc (P x D. Young crossbred boars were performance tested in years 2004-2008 in Poland in Bydgoszcz Breeding Region. The traits taken into account were: age and body weight on the test day, daily gain of body weight standardized on 180th day of life, backfat thickness in P2 and P4 points, height of loin eye in P4 point, lean meat content and the performance test selection index. In a total results summary from years 2004-2008 in tested groups of young crossbred boars (except H x BL negative and in most cases statistically high significant correlations were proved between the growth rate and standardized backfat thickness in P2 and P4 points and in young crossbred boars came from 3 following crossing variants: H x BL, P x H, P x D negative and statistically high significant correlation coefficients were observed between the daily gain of body weight and standardized lean meat content, which may show the unfavourable impact of high growth rate on meat content.

  10. The status of the CABRI test program: Recent results and future activities

    Energy Technology Data Exchange (ETDEWEB)

    Schmitz, F.; Gonnier, Ch.; Papin, J. [Institut de Protection et de Surete Nucleaire, Saint Paul Lez Durance (France)

    1997-01-01

    The first five CABRI experiments of the REP-Na series, all with UO2 fuel and up to a maximum local burnup of 64 GWd/t, have been examined and analyzed and are now reasonably well understood. In March 1996, the first MOX test with a 3 cycle irradiated fuel at 47 GWd/t radially averaged, local maximum burnup has been successfully performed. The rod did not fail and detailed examinations are being obtained and still in progress presently. The available results and findings are presented in this paper. Three experiments of the REP-Na test matrix are still to be performed, REP-Na7, a 4 cycle MOX test, is scheduled in November 1996. The last two experiments, REP-Na 8 the key experiment of the UO2 matrix, and REP-Na 9, a 2 cycle MOX fuel test, will be performed during the first half of 1997. The CABRI tests made with sodium cooling have a good representativity of reactor conditions during some tens of milliseconds. For better simulation on a longer time range, a project study has been undertaken in view of the implementation of a pressurized-water loop into the CABRI reactor. The design of this loop and the performance parameters of the upgraded driver core of CABRI is presented. Finally, the planning of the CABRI transformation and the outlines of the future test matrix is given. The most optimistic estimation allows to predict that the first tests under prototypical test conditions could be performed before the end of 1999.

  11. Test results on parabolic dish concentrators for solar thermal power systems

    Science.gov (United States)

    Jaffe, Leonard D.

    1989-01-01

    This paper presents results of development testing of various solar thermal parabolic dish concentrators. The concentrators were mostly designed for the production of electric power using dish-mounted Rankine, Brayton or Stirling cycle engines, intended to be produced at low cost. Measured performance for various dishes included optical efficiencies ranging from 0.32 to 0.86 at a geometric concentration ratio of 500, and from about 0.09 to 0.85 at a geometric concentration ratio of 3000. Some malfunctions were observed. The tests should provide operating information of value in developing concentrators with improved performance and reduced maintenance.

  12. PICASSO VISION instrument design, engineering model test results, and flight model development status

    Science.gov (United States)

    Näsilä, Antti; Holmlund, Christer; Mannila, Rami; Näkki, Ismo; Ojanen, Harri J.; Akujärvi, Altti; Saari, Heikki; Fussen, Didier; Pieroux, Didier; Demoulin, Philippe

    2016-10-01

    PICASSO - A PICo-satellite for Atmospheric and Space Science Observations is an ESA project led by the Belgian Institute for Space Aeronomy, in collaboration with VTT Technical Research Centre of Finland Ltd, Clyde Space Ltd. (UK) and Centre Spatial de Liège (BE). The test campaign for the engineering model of the PICASSO VISION instrument, a miniaturized nanosatellite spectral imager, has been successfully completed. The test results look very promising. The proto-flight model of VISION has also been successfully integrated and it is waiting for the final integration to the satellite platform.

  13. Testing the Neoclassical Migration Model: Overall and Age-Group Specific Results for German Regions

    DEFF Research Database (Denmark)

    Mitze, Timo; Reinkowski, Janina

    This paper tests the empirical validity of the neoclassical migration model in predicting German internal migration flows. We estimate static and dynamic migration functions for 97 Spatial Planning Regions between 1996 and 2006 using key labor market signals including income and unemployment...... as for age-group specific estimates. Thereby, the impact of labor market signals is tested to be of greatest magnitude for workforce relevant age-groups and especially young cohorts between 18 to 25 and 25 to 30 years. This latter result underlines the prominent role played by labor market conditions...

  14. System structural test results - Six PODS III supports. [Passive Orbital Disconnect Struts

    Science.gov (United States)

    Parmley, Richard T.; Kittel, Peter

    1986-01-01

    Passive orbital disconnect struts can potentially reduce the support conductance a factor of 10 over state-of-the-art tension band nondisconnect supports and cut helium dewar weights in half for the same lifetime. A series of thermal and structural tests were performed to verify that this performance improvement is real. Structural tests on a PODS-III support system (consisting of six struts) is reported here. The results show the predicted performance improvements can be achieved and the PODS-III supports are ready for flight applications. For large tankage systems requiring higher side load capability, a PODS-IV version is currently being developed.

  15. Cold Test Results of the Inner Triplet Orbit Correctors for the LHC

    CERN Document Server

    Venturini-Delsolaro, W

    2006-01-01

    The inner triplet orbit correctors for the LHC, MCBX and MCBXA, underwent acceptance tests at superfluid helium temperature at CERN, before shipping to FNAL for integration in the cold masses. A total of 27 MCBX (Horizontal-Vertical Dipole Correctors), of which 9 MCBXA (with nested Sextupole-Dodecapole insert), are needed for the LHC, including spares. The paper discusses the test protocols for series magnets, and reports the results of quench performance and cold magnetic measurements. The peculiarities of combined training and the hysteresis effects in the nested windings are presented, together with the search of the optimum setting procedure to minimize the persistent current effects on the beam dynamics.

  16. Cryogenic tests of volume-phase holographic gratings: results at 100 K

    CERN Document Server

    Tamura, N; Luke, P; Blackburn, C; Robertson, D J; Dipper, N A; Sharples, R M; Allington-Smith, J R; Tamura, Naoyuki; Murray, Graham J.; Luke, Peter; Blackburn, Colin; Robertson, David J.; Dipper, Nigel A.; Sharples, Ray M.; Allington-Smith, Jeremy R.

    2006-01-01

    We present results from cryogenic tests of Volume-Phase Holographic(VPH) gratings at 100 K. The aims of these tests are to see whether the diffraction efficiency as a function of wavelength is significantly different at a low temperature from that at room temperature and to see how the performance of a VPH grating is affected by a number of thermal cycles. We have completed 10 cycles between room temperature and 100 $K$, and find no clear evidence that the diffraction efficiency changes with temperature or with successive thermal cycle.

  17. First Total Reflection X-Ray Fluorescence round-robin test of water samples: Preliminary results

    Science.gov (United States)

    Borgese, Laura; Bilo, Fabjola; Tsuji, Kouichi; Fernández-Ruiz, Ramón; Margui, Eva; Streli, Christina; Pepponi, Giancarlo; Stosnach, Hagen; Yamada, Takashi; Vandenabeele, Peter; Maina, David M.; Gatari, Michael; Shepherd, Keith D.; Towett, Erick K.; Bennun, Leonardo; Custo, Graciela; Vasquez, Cristina; Depero, Laura E.

    2014-11-01

    Total Reflection X-Ray Fluorescence (TXRF) is a mature technique to evaluate quantitatively the elemental composition of liquid samples deposited on clean and well polished reflectors. In this paper the results of the first worldwide TXRF round-robin test of water samples, involving 18 laboratories in 10 countries are presented and discussed. The test was performed within the framework of the VAMAS project, interlaboratory comparison of TXRF spectroscopy for environmental analysis, whose aim is to develop guidelines and a standard methodology for biological and environmental analysis by means of the TXRF analytical technique.

  18. LOX/LH2 propulsion system for launch vehicle upper stage, test results

    Science.gov (United States)

    Ikeda, T.; Imachi, U.; Yuzawa, Y.; Kondo, Y.; Miyoshi, K.; Higashino, K.

    1984-01-01

    The test results of small LOX/LH2 engines for two propulsion systems, a pump fed system and a pressure fed system are reported. The pump fed system has the advantages of higher performances and higher mass fraction. The pressure fed system has the advantages of higher reliability and relative simplicity. Adoption of these cryogenic propulsion systems for upper stage of launch vehicle increases the payload capability with low cost. The 1,000 kg thrust class engine was selected for this cryogenic stage. A thrust chamber assembly for the pressure fed propulsion system was tested. It is indicated that it has good performance to meet system requirements.

  19. Test Results of High Performance HTS Pancake Coils at 77 K

    Energy Technology Data Exchange (ETDEWEB)

    Lalitha, S. L. [Brookhaven National Lab. (BNL), Upton, NY (United States); Sampson, W. B. [Brookhaven National Lab. (BNL), Upton, NY (United States); Gupta, R. C. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2013-10-25

    A series of pancake coils using several kilometers of second generation (2G) (RE)BCO conductor has been fabricated as a part of a R&D program to build a large aperture high field solenoid for energy storage application. This paper discusses the preparation of double pancake coils and the test results at 77 K before assembling the final magnet. These tests played an important role in assuring: the quality of conductors, coil winding and assembly, and integrity of splices within the coils.

  20. Testing of Subgrid—Scale Stress Models by Using Results from Direct Numerical SImulations

    Institute of Scientific and Technical Information of China (English)

    HongruiGONG

    1998-01-01

    The most commonly used dynamic subgrid models,Germano's model and dynamic kinetic energy model,and their base models-the Smagorinsky model and the kinetic energy model,were tested using results from direct numerical simulations of various turbulent flows.In germano's dynamic model,the model coefficient was treated as a constant within the test filter,This treatment is conceptually inconsistent.An iteration procedure was proposed to calculate the model coefficient and an improved correlation coefficient was found.

  1. First Test Results of the 150 mm Aperture IR Quadrupole Models for the High Luminosity LHC

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosio, G. [Fermilab; Chlachidze, G. [Fermilab; Wanderer, P. [Brookhaven; Ferracin, P. [CERN; Sabbi, G. [LBNL, Berkeley

    2016-10-06

    The High Luminosity upgrade of the LHC at CERN will use large aperture (150 mm) quadrupole magnets to focus the beams at the interaction points. The high field in the coils requires Nb3Sn superconductor technology, which has been brought to maturity by the LHC Accelerator Re-search Program (LARP) over the last 10 years. The key design targets for the new IR quadrupoles were established in 2012, and fabrication of model magnets started in 2014. This paper discusses the results from the first single short coil test and from the first short quadrupole model test. Remaining challenges and plans to address them are also presented and discussed.

  2. Differential GPS/inertial navigation approach/landing flight test results

    Science.gov (United States)

    Snyder, Scott; Schipper, Brian; Vallot, Larry; Parker, Nigel; Spitzer, Cary

    1992-01-01

    Results of a joint Honeywell/NASA-Langley differential GPS/inertial flight test conducted in November 1990 are discussed focusing on postflight data analysis. The test was aimed at acquiring a system performance database and demonstrating automatic landing based on an integrated differential GPS/INS with barometric and radar altimeters. Particular attention is given to characteristics of DGPS/inertial error and the magnitude of the differential corrections and vertical channel performance with and without altimeter augmentation. It is shown that DGPS/inertial integrated with a radar altimeter is capable of providing a precision approach and autoland guidance of manned return space vehicles within the Space Shuttle accuracy requirements.

  3. First Test Results on ITER CS Model Coil and CS Insert

    Energy Technology Data Exchange (ETDEWEB)

    Martovetsky, N; Michael, P; Minervini, J; Radovinsky, A; Takayasu, M; Thome, R; Ando, T; Isono, T; Kato, T; Nakajima, H; Nishijima, G; Nunoya, Y; Sugimoto, M; Takahashi, Y; Tsuji, H; Bessette, D; Okuno, K; Ricci, M; Maix, R

    2000-10-12

    The Inner and Outer modules of the Central Solenoid Model Coil (CSMC) were built by US and Japanese home teams in collaboration with European and Russian teams to demonstrate the feasibility of a superconducting Central Solenoid for ITER and other large tokamak reactors. The CSMC mass is about 120 t, OD is about 3.6 m and the stored energy is 640 MJ at 46 kA and peak field of 13 T. Testing of the CSMC and the CS Insert took place at the Japan Atomic Energy Research Institute (JAERI) from mid March until mid August 2000. This paper presents the main results of the tests performed.

  4. Test results from the 500 kW direct contact pilot plant at East Mesa

    Energy Technology Data Exchange (ETDEWEB)

    Nichols, K.E.; Olander, R.G.; Lobach, J.L.

    1980-09-01

    A 500 kW power plant utilizing direct contact heat exchange (DCHX) between the geothermal brine and the isobutane (IC/sub 4/) working fluid is being operated at the East Mesa test facility. The power plant incorporates a 40-inch-diameter direct-contactor approximately 35 feet tall. The purpose of the pilot plant is to determine the feasibility of large-scale direct-contact heat exchange and power plant operation with the DCHX. The binary cycle offers higher conversion factors (heat energy transformed to electrical energy) than the flashed steam approach for geothermal brines in the 300 to 400/sup 0/F range and preliminary results indicate the DCHX system may have higher performance than the conventional tube-and-shell binary approach. This performance advantage results from the absence of any fouling and the very close pinch temperatures achieved in the DCHX itself. The baseline performance tests for the plant were completed in January 1980. The results of these tests and follow-on testing are covered.

  5. Autologous serum skin test reactivity and basophil histamine release test in patients with nasal polyposis: preliminary results.

    Science.gov (United States)

    Zambetti, G; Ciofalo, A; Soldo, P; Fusconi, M; Romeo, R; Greco, A; Altissimi, G; Macri, G F; Marinelli, C; Pagliuca, G; De Vincentiis, M

    2010-01-01

    An eosinophilic inflammatory process is generally observed in patients suffering from nasal polyposis (NP), however its onset has not yet been defined. It has been suggested that immune activation of inflammatory cells may be the cause. The aim of this study is to verify whether autoantibodies and/or histamine-releasing factors are present in the serum of patients suffering from NP. In fact, we assume that autoantibodies and/or histamine-releasing factors, as already demonstrated in chronic idiopathic urticaria and asthma, may be involved in the pathogenesis of NP. In this case-control analytical study 40 patients with NP and 27 control subjects underwent the in vivo autologous serum skin test (ASST). The sera from 6 patients suffering from NP and 9 control group subjects, who had all been previously studied and randomly selected, underwent basophil histamine release assay from normal donor as a pilot study. The ASST showed positive results in 55% of patients suffering from NP versus 8% of the control group (p= .00006), the basophil histamine release test (BHRT) turned out positive in all patients tested and in 11% of the control group. We found a weak positive correlation between the percentage of histamine release and the wheal diameter. ASST reactivity is very frequent in patients suffering from NP, thus suggesting the presence of histamine-releasing factors in the blood stream. The BHRT was positive in the serum of all patients, thus suggesting the presence of anti-FcepsilonRI, anti-IgE autoantibodies and/or other histamine-releasing factors, the presence of which can play a role in triggering and maintaining the eosinophilic inflammatory process in NP.

  6. Fan Performance Testing and Oxygen Compatibility Assessment Results for Future Space Suit Life Support Systems

    Science.gov (United States)

    Paul, Heather L.; Jennings, Mallory A.; Vogel, Matthew

    2009-01-01

    An advanced portable life support system (PLSS) for the space suit will require a small, robust, and energyefficient system to transport the ventilation gas through the space suit for lunar Extravehicular Activity (EVA) operations. A trade study identified and compared ventilation transport technologies in commercial, military, and space applications to determine which technologies could be adapted for EVA use. Based on the trade study results, five commercially available, 24-volt fans were selected for performance testing at various pressures and flow rates. Measured fan parameters included fan delta-pressures, input voltages, input electrical currents, and in some cases motor windings electrical voltages and currents. In addition, a follow-on trade study was performed to identify oxygen compatibility issues and assess their impact on fan design. This paper outlines the results of the fan performance characterization testing, as well as the results from the oxygen compatibility assessment.

  7. Test results of reliable and very high capillary multi-evaporators / condenser loop

    Energy Technology Data Exchange (ETDEWEB)

    Van Oost, S.; Dubois, M.; Bekaert, G. [Societe Anonyme Belge de Construction Aeronautique - SABCA (Belgium)

    1996-12-31

    The paper present the results of various SABCA activities in the field of two-phase heat transport system. These results have been based on a critical review and analysis of the existing two-phase loop and of the future loop needs in space applications. The research and the development of a high capillary wick (capillary pressure up to 38 000 Pa) are described. These activities have led towards the development of a reliable high performance capillary loop concept (HPCPL), which is discussed in details. Several loop configurations mono/multi-evaporators have been ground tested. The presented results of various tests clearly show the viability of this concept for future applications. Proposed flight demonstrations as well as potential applications conclude this paper. (authors) 7 refs.

  8. SOURCES OF DIFFERENCES IN CALCULATIONS AND EXPERIMENTAL TEST RESULTS OF FATIGUE LIFE OF STRUCTURAL ELEMENTS

    Directory of Open Access Journals (Sweden)

    Józef SZALA

    2014-06-01

    Full Text Available Calculation results are the base for evaluation of fatigue life of structural elements during machine design processes. It results from the fact that there are no material objects in the phase of existence of a product. Reliability of tests results is an essential element in the calculation fatigue life evaluation method and it can be evaluated by comparison of the results with experimental ones. In the paper there was performed an analysis of the chosen factors essentially influencing conformity of calculation results and experimental test ones connected with basic elements of a calculation algorithm including: - elaboration and analysis of service loadings of a structural element, - determination and analysis of cyclic properties of structural elements, - selection of fatigue damage accumulation hypothesis being a description of fatigue life processes. The mentioned analysis was illustrated with examples of fatigue life tests performed in the Machine Design Department of the University of Technology and Agriculture within the research grant no. 2221/B/T02/2010/39 financed by The Ministry of Science and Higher Education and National Science Centre.

  9. Comparison of clinical diagnosis and microbiological test results in vaginal infections.

    Science.gov (United States)

    Karaca, M; Bayram, A; Kocoglu, M E; Gocmen, A; Eksi, F

    2005-01-01

    Lower genital tract infections continue to be a problem due to the fact that the clinical diagnosis is usually inadequate, and subsequent care is suboptimal. This study aimed at evaluating the accuracy of clinical diagnosis by comparing it with microbiologic test results, and to determine the causative agents of vaginal infections. Sixty-seven nonpregnant women (18-45 years of age) with the clinical diagnosis of lower genital tract infection were enrolled in the study. Patients were not included if they had a history of vaginal infection during the previous three-month period or intrauterine device. The clinical diagnosis was based on the combinations of symptoms, direct observation of wet mount, homogeneous discharge, vaginal pH > 4.5, and detection of the amine odor after exposure of vaginal secretions to 10% KOH. Vaginal samples were taken with two cotton swabs, one was used for pH determination, and the second was utilized for microbiological tests. Gram staining and cultures with Sabouraud agar and chocolate agar were performed for microbiological diagnosis, and the results were compared. The clinical diagnoses included 26 (38.8%) candidiasis, 18 (26.8%) bacterial vaginosis, three (4.5%) trichomoniasis, and 20 (29.9%) mixed vaginal infections. Of the 26 patients with clinical diagnoses of candidiasis, 12 (46.1%) revealed Candiada albicans, nine (34.6) patients revealed microorganisms other than candida species, and five (19.2%) patients had no growth. Five (27.8%) bacterial vaginosis patients revealed Gardnarella vaginalis and 12 patients (66.6%) did not grow any microorganism. The overall rate of accurate clinical diagnoses confirmed by microbiological test results was 43.2%. Seventeen (43.6) of the 39 microbiological test results correlated with clinical diagnosis, and no growth was observed in 28 (41.8%) cultures. We conclude that the clinical diagnosis of vaginal infection is inadequate and should be confirmed with microbiological testing if the resources

  10. Buffer substitution in malaria rapid diagnostic tests causes false-positive results

    Directory of Open Access Journals (Sweden)

    Van den Ende Jef

    2010-07-01

    Full Text Available Abstract Background Malaria rapid diagnostic tests (RDTs are kits that generally include 20 to 25 test strips or cassettes, but only a single buffer vial. In field settings, laboratory staff occasionally uses saline, distilled water (liquids for parenteral drugs dilution or tap water as substitutes for the RDT kit's buffer to compensate for the loss of a diluent bottle. The present study assessed the effect of buffer substitution on the RDT results. Methods Twenty-seven RDT brands were run with EDTA-blood samples of five malaria-free subjects, who were negative for rheumatoid factor and antinuclear antibodies. Saline, distilled water and tap water were used as substitute liquids. RDTs were also run with distilled water, without adding blood. Results were compared to those obtained with the RDT kit's buffer and Plasmodium positive samples. Results Only eight cassettes (in four RDT brands showed no control line and were considered invalid. Visible test lines occurred for at least one malaria-free sample and one of the substitutes in 20/27 (74% RDT brands (saline: n = 16; distilled water: n = 17; and tap water: n = 20, and in 15 RDTs which were run with distilled water only. They occurred for all Plasmodium antigens and RDT formats (two-, three- and four-band RDTs. Clearance of the background of the strip was excellent except for saline. The aspects (colour, intensity and crispness of the control and the false-positive test lines were similar to those obtained with the RDT kits' buffer and Plasmodium positive samples. Conclusion Replacement of the RDT kit's dedicated buffer by saline, distilled water and tap water can cause false-positive test results.

  11. Thermo-Hydro-Mechanical properties of MX-80. Results from advanced laboratory tests

    Energy Technology Data Exchange (ETDEWEB)

    Dueck, Ann; Nilsson, Ulf (Clay Technology AB, Lund (Sweden))

    2010-12-15

    General Highly compacted bentonite is proposed as the buffer material in the Swedish concept for disposal of nuclear waste. The saturated homogenized bentonite is expected to fully act as a buffer material between the waste canister and the surrounding bedrock. Material models describing the thermo-hydro-mechanical (THM) behaviour of the buffer material have been created with the purpose to simulate and predict the behaviour in a repository both before and after water saturation. The material models of water saturated and water unsaturated buffer material are complicated and contain a number of parameters that need to be determined. The present report is a compilation of results concerning thermo-hydro-mechanical laboratory tests on saturated and unsaturated buffer material. The main purpose of the report is to supply modelling groups with available results for improving models and determine parameters that can be used for the THM modelling of the behaviour of the buffer.Retention curves The relation between water content and relative humidity has been determined in a number of test series for some specific conditions, e.g. different initial water contents. Two methods have been used; the sorption balance method and a method with jars as desiccators. The majority of the results were derived from tests where RH was controlled and the response of the bentonite samples was measured. The results are given as water content versus relative humidity in diagrams and in tabular form. Volume change The volume change of water unsaturated bentonite specimens has been investigated by compression tests and swelling/shrinkage tests for some specific stress and moisture paths. The constant relative humidity was generated by the vapour equilibrium technique combined with an air circulation system. Measured stresses, deformation and relative humidity are presented versus time in diagrams and the final values at different stages are also presented in tabular form. Moisture transport

  12. Upper Stage Flight Experiment 10K Engine Design and Test Results

    Science.gov (United States)

    Ross, R.; Morgan, D.; Crockett, D.; Martinez, L.; Anderson, W.; McNeal, C.

    2000-01-01

    A 10,000 lbf thrust chamber was developed for the Upper Stage Flight Experiment (USFE). This thrust chamber uses hydrogen peroxide/JP-8 oxidizer/fuel combination. The thrust chamber comprises an oxidizer dome and manifold, catalyst bed assembly, fuel injector, and chamber/nozzle assembly. Testing of the engine was done at NASA's Stennis Space Center (SSC) to verify its performance and life for future upper stage or Reusable Launch Vehicle applications. Various combinations of silver screen catalyst beds, fuel injectors, and combustion chambers were tested. Results of the tests showed high C* efficiencies (97% - 100%) and vacuum specific impulses of 275 - 298 seconds. With fuel film cooling, heating rates were low enough that the silica/quartz phenolic throat experienced minimal erosion. Mission derived requirements were met, along with a perfect safety record.

  13. Increase in contact allergy to fragrances: patch-test results 1989-1998.

    Science.gov (United States)

    Lunder, T; Kansky, A

    2000-08-01

    We report the results of patch tests with fragrance-mix as a part of the standard series carried out over the last 10 years (1989-1998) during routine testing of 6129 patients in our department. 5.9% of the total number of patients who were patch tested were positive to fragrance mix. The sex ratio was 2.3:1 with a female predominance. In 1989-1993, the frequency of contact sensitivity to fragrance mix was 3.9% (4.9% for females and 2.1% for males). This rate rose both in female and male patients during the observed period of time and attained 8.9% (females) and 4.1% (males) in 1994-1998; the overall frequency in 1994-98 was 7.5%. This rising trend, which was statistically significant, might be the consequence of an increased use of cosmetics and toiletries containing fragrances in our population.

  14. ELECTROCHEMICAL CORROSION TEST RESULTS FOR TANK 241-SY-102 SUPERNATE GRAB SAMPLES

    Energy Technology Data Exchange (ETDEWEB)

    DUNCAN JB

    2007-04-09

    This report describes the electrochemical corrosion scans and conditions for testing of SY-102 supernatant samples taken December 2004. The testing was performed because the tank was under a Justification for Continued Operation allowing the supernatant composition to be outside the chemistry limits of Administrative Control 5.16, 'Corrosion Mitigation program'. A new electrochemical working electrode of A516 Grade 60 carbon steel was used for each scan; all scans were measured against a saturated calomel electrode, with carbon counter electrodes, and all scans were carried out at 50 C. The samples were scanned twice, once as received and once sparged with argon to deoxygenate the sample. For those scans conducted after argon purging, the corrosion rates ranged from 0.012 to 0.019 mpy. A test for stress corrosion cracking was carried out on one sample (2SY-04-07) with negative results.

  15. Testing general relativity with black-hole binary observations: results and prospects

    Science.gov (United States)

    Vallisneri, Michele

    2017-01-01

    The first two LIGO-Virgo detections of gravitational waves from binary black-hole inspirals offered the first opportunity to test gravitation in its strong-field, relativistic-motion, and radiative sector. The initial tests reported in PRL 116 (2016) probed consistency with the predictions of general relativity, to moderate precision. The space-based observatory LISA will observe black-hole binary signals with much larger SNRs, allowing for even more precise tests. Last, the detection of a binary black-hole stochastic background with pulsar-timing arrays will offer more constraints on the speed and polarizations of gravitational waves. I review these results and examine synergies across the gravitational-wave spectrum. I discuss the main challenges and opportunities from the viewpoint of data analysis, and outline prospects for making contact with current alternative theories of gravitation, in particular those motivated by models of dark energy.

  16. Results of the first nuclear blowdown test on single fuel rods (LOC-11 Series in PBF)

    Energy Technology Data Exchange (ETDEWEB)

    Larson, J.R.; Evans, D.R.; McCardell, R.K.

    1978-01-01

    This paper presents results of the first nuclear blowdown tests (LOC-11A, LOC-11B, LOC-11C) ever conducted. The Loss-of-Coolant Accident (LOCA) Test Series is being conducted in the Power Burst Facility (PBF) reactor at the Idaho National Engineering Laboratory, near Idaho Falls, Idaho, for the Nuclear Regulatory Commission. The objective of the LOC-11 tests was to obtain data on the behavior of pressurized and unpressurized rods when exposed to a blowdown similar to that expected in a pressurized water reactor (PWR) during a hypothesized double-ended cold-leg break. The data are being used for the development and verification of analytical models that are used to predict coolant and fuel rod pressure during a LOCA in a PWR.

  17. Test and analysis results for two Synergy Power Corp. wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Davis, D.; Hansen, C. [Windward Engineering, L.C., Salt Lake City, UT (United States)

    1996-12-31

    The testing and modeling of small (rotor diameter 10.3 m and 12.8 m) wind turbines is the subject of this paper. The paper focuses primarily on the ADAMS computer model for dynamic analysis. The code calculates design loads, optimizes tilt configuration, and helps to interpret test results. A comparison of some of the modeling predictions is made to test data for validation purposes. The ADAMS model was found to accurately predict performance characteristics and loads for free-tilting turbines. ADAMS was found to be relatively successful in modeling the free tilt and variable rotors. The model also showed that tilting behavior is dependent on the restoring moment from the rotor aerodynamics as well as on surface aerodynamics. The effects of changes in air density on the power curve, load predictions, and analysis of emergency stops were also performed satisfactorily with the model. 15 figs.

  18. Drug testing in Europe: monitoring results of the Trans European Drug Information (TEDI) project.

    Science.gov (United States)

    Brunt, Tibor M; Nagy, Constanze; Bücheli, Alexander; Martins, Daniel; Ugarte, Miren; Beduwe, Cécile; Ventura Vilamala, Mireia

    2017-02-01

    Drug testing is a harm reduction strategy that has been adopted by certain countries in Europe. Drug users are able to hand in their drugs voluntarily for chemical analysis of composition and dose. Drug users will be alerted about dangerous test results by the drug testing systems directly and through warning campaigns. An international collaborative effort was launched to combine data of drug testing systems, called the Trans European Drug Information (TEDI) project. Drug testing systems of Spain, Switzerland, Belgium, Austria, Portugal, and the Netherlands participated in this project. This study presents results of some of the main illicit drugs encountered: cocaine, ecstasy and amphetamine and also comments on new psychoactive substances (NPS) detected between 2008 and 2013. A total of 45 859 different drug samples were analyzed by TEDI. The drug markets of the distinct European areas showed similarities, but also some interesting differences. For instance, purity of cocaine and amphetamine powders was generally low in Austria, whilst high in Spain and the Netherlands. And the market for ecstasy showed a contrast: whereas in the Netherlands and Switzerland there was predominantly a market for ecstasy tablets, in Portugal and Spain MDMA (3,4-methylenedioxymethamphetamine) crystals were much more prevalent. Also, some NPS appearing in ecstasy seemed more specific for one country than another. In general, prevalence of NPS clearly increased between 2008 and 2013. Drug testing can be used to generate a global picture of drug markets and provides information about the pharmacological contents of drugs for the population at risk. Copyright © 2016 John Wiley & Sons, Ltd.

  19. Final results of the tests on the resistive plate chambers for the ALICE muon arm

    Energy Technology Data Exchange (ETDEWEB)

    Arnaldi, R. [INFN, Sezione di Torino (Italy); Baldit, A.; Barret, V.; Bastid, N.; Blanc, A.; Blanchard, G. [LPC Clermont Ferrand, IN2P3/CNRS, Universite Blaise Pascal (France); Chiavassa, E. [INFN, Sezione di Torino (Italy); Dipartimento di Fisica Sperimentale dell' Universita di Torino (Italy); Cortese, P. [INFN, Sezione di Torino (Italy); Dipartimento di Scienze e Tecnologie, Avanzate dell' Universita del Piemonte Orientale (Italy); Crochet, P. [LPC Clermont Ferrand, IN2P3/CNRS, Universite Blaise Pascal (France); Dellacasa, G. [INFN, Sezione di Torino (Italy); Dipartimento di Scienze e Tecnologie, Avanzate dell' Universita del Piemonte Orientale (Italy); De Marco, N. [INFN, Sezione di Torino (Italy); Devaux, A.; Dupieux, P. [LPC Clermont Ferrand, IN2P3/CNRS, Universite Blaise Pascal (France); Ferretti, A.; Gallio, M. [INFN, Sezione di Torino (Italy); Dipartimento di Fisica Sperimentale dell' Universita di Torino (Italy); Gemme, R. [INFN, Sezione di Torino (Italy); Dipartimento di Scienze e Tecnologie, Avanzate dell' Universita del Piemonte Orientale (Italy); Grygorian, S.; Insa, C.; Jouve, F.; Lopez, X. [LPC Clermont Ferrand, IN2P3/CNRS, Universite Blaise Pascal (France)] (and others)

    2009-05-01

    The trigger for the ALICE muon spectrometer will be issued by single-gap, low resistivity bakelite resistive plate chambers (RPCs). The trigger system consists of four 5.5x6.5m{sup 2} RPC planes arranged in two stations, for a total of 72 detectors. One hundred and sixteen detectors have been assembled and tested in Torino. The tests have been performed with the streamer mixture developed for heavy ion data-taking. The tests include: the detection of gas leaks and parasitic currents; the measurement of the efficiency with cosmic rays, with particular regard to the uniformity of the efficiency throughout the whole active surface, with a granularity of about 2x2cm{sup 2}; the measurement of the dark current and of the mean and localised noise rate. All the RPCs produced have been characterised. Among them, the detectors to be finally installed in ALICE and some spare have been selected; 17% of all the produced detectors have been discarded. A short description of the test set-up is given. The results of the tests are presented, with particular regard to the performance of the selected detectors.

  20. Test Results For a 25-m Prototype Fault Current Limiting HTS Cable for Project Hydra

    Energy Technology Data Exchange (ETDEWEB)

    Rey, Christopher M [ORNL; Duckworth, Robert C [ORNL; Demko, Jonathan A [ORNL; Ellis, Alvin R [ORNL; Gouge, Michael J [ORNL; James, David Randy [ORNL; Tuncer, Enis [ORNL

    2010-01-01

    The Oak Ridge National Laboratory (ORNL) has tested a 25-m long prototype High Temperature Superconducting (HTS) cable with inherent Fault-Current Limiting (FCL) capability at its recently upgraded HTS cable test facility in Oak Ridge, TN. The HTS-FCL cable and terminations were designed and fabricated by Ultera, which is a joint venture of Southwire and nkt cables with FCL features and HTS wire provided by American Superconductor Corporation. The overall project is sponsored by the U.S. Department of Homeland Security. The ultimate goal of the 25-m HTS-FCL cable test program was to verify the design and ensure the operational integrity for the eventual installation of a ~ 200-m fully functional HTS-FCL cable in the Consolidated Edison electric grid located in downtown New York City. The 25-m HTS-FCL cable consisted of a three-phase (3- ) Triax design with a cold dielectric between the phases. The HTS-FCL cable had an operational voltage of 13.8 kV phase-to-phase and an operating current of 4000 Arms per phase, which is the highest operating current to date of any HTS cable. The 25-m HTS-FCL cable was subjected to a series of cryogenic and electrical tests. Test results from the 25-m HTS-FCL cable are presented and discussed.