WorldWideScience

Sample records for analyzing power

  1. Loviisa nuclear power plant analyzer

    International Nuclear Information System (INIS)

    The APROS Simulation Environment has been developed since 1986 by Imatran Voima Oy (IVO) and the Technical Research Centre of Finland (VTT). It provides tools, solution algorithms and process components for use in different simulation systems for design, analysis and training purposes. One of its main nuclear applications is the Loviisa Nuclear Power Plant Analyzer (LPA). The Loviisa Plant Analyzer includes all the important plant components both in the primary and in the secondary circuits. In addition, all the main control systems, the protection system and the high voltage electrical systems are included. (orig.)

  2. Narrow structures observed in the p-p analyzing power

    International Nuclear Information System (INIS)

    The momentum dependence of the p-p elastic analyzing power has been measured in small steps using an internal target during polarized beam acceleration from 1 to 3 GeV/c. The momentum bin size ranges from 5 to 18 MeV/c. The relative uncertainty of the analyzing power is typically less than 0.01 for each momentum bin. Narrow structures have been observed in the two-proton invariant mass distribution of the analyzing power. A brief discussion on the interpretation of the present results is also given. 11 refs., 7 figs., 1 tab

  3. np elastic scattering analyzing power characteristics at intermediate energies

    International Nuclear Information System (INIS)

    Recent measurements of charge symmetry breaking in the np system at 477 MeV, and of Aoonn for np elastic scattering at 220, 325 and 425 MeV also yield accurate analyzing power data. These data allow the energy dependence of the analyzing power zero-crossing angle and the slope of the analyzing power at the zero-crossing to be determined. The incident neutron energies span a region where the zero-crossing angle is strongly energy dependent (Εn n > 350 MeV). The results are compared to current phase shift analysis predictions, recently published LAMPF data, and the predictions of the Bonn and Paris potentials. (Author) 13 refs., 2 tabs., 2 figs

  4. Time asymmetry: Polarization and analyzing power in the nuclear reactions

    International Nuclear Information System (INIS)

    Measurements of the proton polarization in the reactions 7Li(3He, p vector)9Be and 9Be(3He, p vector)11B and of the analyzing powers of the inverse reactions, initiated by polarized protons at the same c.m. energies, show significant differences which imply the failure of the polarization-analyzing-power theorem and, prima facie, of time-reversal invariance in these reactions. The reaction 2H(3He, p vector)4 He and its inverse have also been investigated and show some smaller differences. A discussion of the instrumental asymmetries is presented. (orig.)

  5. Monitoring and analyzing features of electrical power quality system performance

    Directory of Open Access Journals (Sweden)

    Genci Sharko

    2010-06-01

    Full Text Available Power quality is a set of boundaries that allows electrical systems to function in their intended manner without significant loss of performance or life. The term is used to describe electric power that drives an electrical load and the load's ability to function properly with that electric power. Without the proper quality of the power, an electrical device may malfunction, fail prematurely or not operate at all. There are many reasons why the electric power can be of poor quality and many more causes of such poor quality power. Power quality of power systems, which affects all connected electrical and electronic equipment, is a measure of deviations in voltages, currents, frequency, temperatures, winding forces and torques of particular supply systems and their components. In recent years, a considerable increase in nonlinear loads has been experienced; in particular distributed loads, such as computers, monitors and lighting, and distributed sources. The aim of this paper is to display a way of monitoring and analyzing features of electrical power quality system. As a monitoring example is taken output from power transformer rated at 320 kVA, part of distribution grid of Durres City in Albania.

  6. Analyzing Single-Event Gate Ruptures In Power MOSFET's

    Science.gov (United States)

    Zoutendyk, John A.

    1993-01-01

    Susceptibilities of power metal-oxide/semiconductor field-effect transistors (MOSFET's) to single-event gate ruptures analyzed by exposing devices to beams of energetic bromine ions while applying appropriate bias voltages to source, gate, and drain terminals and measuring current flowing into or out of each terminal.

  7. A DEPLHI BASED POWER MONITORING SOFTWARE DEVELOPED FOR ENERGY ANALYZERS

    Directory of Open Access Journals (Sweden)

    A. Serdar YILMAZ

    2006-03-01

    Full Text Available In this paper, a Delphi based interface software developed for energy analyzers is presented. Transferring the electrical parameters which is read from the energy analyzer to the computer in real-time has been achieved by using the developed software. It is also possible to record the parameters such as current, voltage, power, harmonic distortion and etc in real-time and to illustrate these recorded parameters in comparison with each other and graphically. Presented software is developed for Merlin Gerin Powerlogic PM 800 power analyzers and also it is usable for different trademarks and models which use Modbus protocol. Proposed software permits intercommunication and observation between maximum 256 devices. Recorded data can be monitorized in table and graphic form for requested time and date intervals by the users. In the study, Borland Delphi v.7.0 is preferred due to flexible and fast. Developed software can be easily used for energy distribution automation and monitoring of the power flow and power quality and also it is a user friendly interface.

  8. Analyzing the Low Power Wireless Links for Wireless Sensor Networks

    CERN Document Server

    Mamun, Md Mainul Islam; Kumar, Sumon; Islam, Md Zahidul

    2010-01-01

    There is now an increased understanding of the need for realistic link layer models in the wireless sensor networks. In this paper, we have used mathematical techniques from communication theory to model and analyze low power wireless links. Our work provides theoretical models for the link layer showing how Packet Reception Rate vary with Signal to Noise Ratio and distance for different modulation schemes and a comparison between MICA2 and TinyNode in terms of PRR.

  9. Vector and tensor analyzing powers in deuteron-proton breakup

    International Nuclear Information System (INIS)

    Vector and tensor analyzing powers of the 1H(d-bar,pp)n breakup reaction at 130 and 100 MeV deuteron beam energies have been measured at KVI Groningen with the use of the detection systems covering large fractions of the phase space. The high precision data are compared to the theoretical predictions based on various approaches to describe the three nucleon (3N) system dynamics. Theoretical predictions describe very well the vector analyzing power data, with no need to include any three-nucleon force effects for these observables. The tensor analyzing powers can be also very well reproduced by calculations in most of the studied region, but locally certain discrepancies are observed. At 130 MeV for Axy such discrepancies usually appear, or are enhanced, when model 3N forces (3NFs), TM99 or Urbana IX, are included. Problems of all theoretical approaches with describing Axx and Ayy are limited to very small regions of the phase space, usually characterized with the lowest relative energies of the two protons. Predicted effects of 3NFs are much lower at 100 MeV, therefore at this energy equally good consistency between the data and the calculations is obtained with or without 3NFs.

  10. Using Model Checking for Analyzing Distributed Power Control Problems

    Directory of Open Access Journals (Sweden)

    Thomas Brihaye

    2010-01-01

    Full Text Available Model checking (MC is a formal verification technique which has been known and still knows a resounding success in the computer science community. Realizing that the distributed power control (PC problem can be modeled by a timed game between a given transmitter and its environment, the authors wanted to know whether this approach can be applied to distributed PC. It turns out that it can be applied successfully and allows one to analyze realistic scenarios including the case of discrete transmit powers and games with incomplete information. The proposed methodology is as follows. We state some objectives a transmitter-receiver pair would like to reach. The network is modeled by a game where transmitters are considered as timed automata interacting with each other. The objectives are then translated into timed alternating-time temporal logic formulae and MC is exploited to know whether the desired properties are verified and determine a winning strategy.

  11. Analyzing power in the mass-six supermultiplet system

    International Nuclear Information System (INIS)

    Analyzing powers Asub(y) for reactions leading to several members of the mass-six supermultiplet have been measured via the t(pol)+9Be→6Li + 6He, 6Li*+6He reactions at 17 MeV triton energy. In contrast to the previously measured differential cross sections, which show symmetry about 900 for both the S=1 and S=0 channels. Asub(y) is consistent with being antisymmetry about 900 for the S=0 channel and is approximately symmetric for the S=1 channel. An antisymmetric result for the S=0 isospin-multiplet channel could be understood by invoking isospin symmetry, in analogy to the well-known Barshay-Temmer theorem. The reaction leading to the S=1 channel is discussed in terms of a direct reaction mechanism; however, the symmetry of Asub(y) about 900 is not understood. (Auth.)

  12. Governance of Aquatic Agricultural Systems: Analyzing Representation, Power, and Accountability

    Directory of Open Access Journals (Sweden)

    Blake D. Ratner

    2013-12-01

    Full Text Available Aquatic agricultural systems in developing countries face increasing competition from multiple stakeholders over rights to access and use natural resources, land, water, wetlands, and fisheries, essential to rural livelihoods. A key implication is the need to strengthen governance to enable equitable decision making amidst competition that spans sectors and scales, building capacities for resilience, and for transformations in institutions that perpetuate poverty. In this paper we provide a simple framework to analyze the governance context for aquatic agricultural system development focused on three dimensions: stakeholder representation, distribution of power, and mechanisms of accountability. Case studies from Cambodia, Bangladesh, Malawi/Mozambique, and Solomon Islands illustrate the application of these concepts to fisheries and aquaculture livelihoods in the broader context of intersectoral and cross-scale governance interactions. Comparing these cases, we demonstrate how assessing governance dimensions yields practical insights into opportunities for transforming the institutions that constrain resilience in local livelihoods.

  13. The optimization of spectrum in the power analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Wu, R.C.; Chen, H.M. [I-Shou Univ., Kaohsiung, Taiwan (China). Dept. of Electrical Engineering; Ou, T.C. [National Sun Yat-Sen Univ., Kaohsiung, Taiwan (China). Dept. of Electrical Engineering; Tsai, J.I. [Kao Yuan Univ., Kaohsiung, Taiwan (China). Dept. of Electronic Engineering

    2008-07-01

    A study was conducted to investigate spectra under different sampling rates by amplitude summation and purpose V curve. The objective was to promote the accuracy of the spectrum in the power analyzer, which is influenced by different sampling rates. The study revealed that as soon as an optimal sampling rate is determined, an optimal spectrum can also be determined. Since the relationship between the amplitude summation and the sampling rate is that of a type V curve, the optimal solution can be obtained quickly. The study also compared results of Fast Fourier Transformation (FFT) and the optimal spectrum to prove the accuracy of this method. This method also offers a solution to common errors, including the picket-fence effect and leakage effect which result from the sampling period being different to the time of the signal period. By adjusting the sampling rate, the frequency scale can be changed to match the signal parameter. As such, the leakage effect can be eliminated and the exact parameter can be displayed on the spectrum. 10 refs., 3 tabs., 5 figs.

  14. Regional modeling approach for analyzing harmonic stability in radial power electronics based power system

    DEFF Research Database (Denmark)

    Yoon, Changwoo; Bai, Haofeng; Wang, Xiongfei; Bak, Claus Leth; Blaabjerg, Frede

    2015-01-01

    Stability analysis of distributed power generation system becomes complex when there are many numbers of grid inverters in the system. In order to analyze system stability, the overall network impedance will be lumped and needs to be analyzed one by one. However, using a unified bulky transfer......-function creates an ambiguity of knowing the reason of instability and also there is no fixed way of choosing the sequence of the analysis. This paper suggests a method to perform a regional stability analysis in the distribution power system. The main idea is started from the simplest stability analysis entity...

  15. Power quality analyzer device modeling by real time SIMULINK MATLAB

    Energy Technology Data Exchange (ETDEWEB)

    Martins, C.H.N.; Silva, L.R.M.; Fabri, D.F.; Duque, C.A. [Federal University of Juiz de Fora (UFJF), MG (Brazil)], Emails: chnmartins@yahoo.com.br, leandro.manso@engenharia.ufjf.br, Diego.fabri@engenharia.ufjf.br, Carlos.duque@ufjf.br; Ribeiro, P.F. [Calvin College, Grand Rapids, MI (United States)], E-mail: pfribeiro@ieee.org

    2009-07-01

    The expansion of electronic devices have increased non linear loads. The effect is high levels of electric disturbances and EMC and EMI interferences. The control of power quality parameters are of primordial importance to ensure minimal power quality. This paper deals with the modeling, simulation and development of a device capable of measuring electrical events. (author)

  16. Using Model Checking for Analyzing Distributed Power Control Problems

    DEFF Research Database (Denmark)

    Brihaye, Thomas; Jungers, Marc; Lasaulce, Samson; Markey, Nicolas; Oreiby, Ghassan

    2010-01-01

    Model checking (MC) is a formal verification technique which has been known and still knows a resounding success in the computer science community. Realizing that the distributed power control ( PC) problem can be modeled by a timed game between a given transmitter and its environment, the authors...

  17. Analyzing Small Signal Stability of Power System based on Online Data by Use of SMES

    Science.gov (United States)

    Ishikawa, Hiroyuki; Shirai, Yasuyuki; Nitta, Tanzo; Shibata, Katsuhiko

    The purpose of this study is to estimate eigen-values and eigen-vectors of a power system from on-line data to evaluate the power system stability. Power system responses due to the small power modulation of known pattern from SMES (Superconducting Magnetic Energy Storage) were analyzed, and the transfer functions between the power modulation and power oscillations of generators were obtained. Eigen-values and eigen-vectors were estimated from the transfer functions. Experiments were carried out by use of a model SMES and Advanced Power System Analyzer (APSA), which is an analogue type power system simulator of Kansai Electric Power Company Inc., Japan. Changes in system condition were observed by the estimated eigen-values and eigen-vectors. Result agreed well with the resent report and digital simulation. This method gives a new application for SMES, which will be installed for improving electric power quality.

  18. Observation of narrow structures in the p-p analyzing power around 1 GeV

    International Nuclear Information System (INIS)

    The momentum dependence of the analyzing power Ay in proton-proton elastic scattering has been measured in small steps using an internal target inserted into a polarized proton beam during acceleration from 1 to 3 GeV/c. The momentum bin size ranges from 5 to 18 MeV/c. The relative uncertainty of the analyzing power, ΔAy, is typically less than 0.01 for each momentum bin. Narrow structures have been observed in the two-proton invariant mass distribution of the analyzing power. 15 refs., 5 figs., 1 tab

  19. Characterization of supercapacitor models for analyzing supercapacitors connected to constant power elements

    Science.gov (United States)

    Yang, Hengzhao; Zhang, Ying

    2016-04-01

    Understanding the power and energy performance of supercapacitors connected to constant power elements is important for many applications. This paper proposes a characterization method for two supercapacitor models that are used to analyze the power and energy behavior of supercapacitors connected to constant power elements: linear capacitance model and constant capacitance model. The linear or constant capacitance is determined by conducting a constant power experiment. A set of constant power experiments is designed. The proposed method can reduce the error in estimating the constant power experiment time for a variety of supercapacitor samples with different rated capacitance and voltage. The accuracy of using the linear capacitance model and the constant capacitance model is approximately equal. Moreover, the performance evaluation results suggest that using the linear or constant capacitance fitted through a low power discharge experiment can minimize the error, which can serve as a guideline to design the constant power experiment.

  20. Development of general-purpose software to analyze the static thermal characteristic of nuclear power plant

    International Nuclear Information System (INIS)

    We have developed the general-purpose software by which static thermal characteristic of the power generation system is analyzed easily. This software has the notable features as follows. It has the new algorithm to solve non-linear simultaneous equations to analyze the static thermal characteristics such as heat and mass balance, efficiencies, etc. of various power generation systems. It has the flexibility for setting calculation conditions. It is able to be executed on the personal computer easily and quickly. We ensured that it is able to construct heat and mass balance diagrams of main steam system of nuclear power plant and calculate the power output and efficiencies of the system. Furthermore, we evaluated various heat recovery measures of steam generator blowdown water and found that this software could be a useful operation aid for planning effective changes in support of power stretch. (author)

  1. Development of General-Purpose Software to Analyze the Static Thermal Characteristic of Nuclear Power Plant

    Science.gov (United States)

    Nakao, Yoshinobu; Koda, Eiichi; Takahashi, Toru

    We have developed the general-purpose software by which static thermal characteristic of the power generation system is analyzed easily. This software has the notable features as follows. -It has the new algorithm to solve non-linear simultaneous equations to analyze the static thermal characteristics such as heat and mass balance, efficiencies, etc. of various power generation systems. -It has the flexibility for setting calculation conditions. -It is able to be executed on the personal computer easily and quickly. We ensured that it is able to construct heat and mass balance diagrams of main steam system of nuclear power plant and calculate the power output and efficiencies of the system. Furthermore, we evaluated various heat recovery measures of steam generator blowdown water and found that this software could be a useful operation aid for planning effective changes in support of power stretch.

  2. Synchronized Phasor Data for Analyzing Wind Power Plant Dynamic Behavior and Model Validation

    Energy Technology Data Exchange (ETDEWEB)

    Wan, Y. H.

    2013-01-01

    The U.S. power industry is undertaking several initiatives that will improve the operations of the power grid. One of those is the implementation of 'wide area measurements' using phasor measurement units (PMUs) to dynamically monitor the operations and the status of the network and provide advanced situational awareness and stability assessment. This project seeks to obtain PMU data from wind power plants and grid reference points and develop software tools to analyze and visualize synchrophasor data for the purpose of better understanding wind power plant dynamic behaviors under normal and contingency conditions.

  3. Analyzing Effects of Turbulence on Power Generation Using Wind Plant Monitoring Data: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, J.; Chowdhury, S.; Hodge, B. M.

    2014-01-01

    In this paper, a methodology is developed to analyze how ambient and wake turbulence affects the power generation of a single wind turbine within an array of turbines. Using monitoring data from a wind power plant, we selected two sets of wind and power data for turbines on the edge of the wind plant that resemble (i) an out-of-wake scenario (i.e., when the turbine directly faces incoming winds) and (ii) an in-wake scenario (i.e., when the turbine is under the wake of other turbines). For each set of data, two surrogate models were then developed to represent the turbine power generation (i) as a function of the wind speed; and (ii) as a function of the wind speed and turbulence intensity. Support vector regression was adopted for the development of the surrogate models. Three types of uncertainties in the turbine power generation were also investigated: (i) the uncertainty in power generation with respect to the published/reported power curve, (ii) the uncertainty in power generation with respect to the estimated power response that accounts for only mean wind speed; and (iii) the uncertainty in power generation with respect to the estimated power response that accounts for both mean wind speed and turbulence intensity. Results show that (i) under the same wind conditions, the turbine generates different power between the in-wake and out-of-wake scenarios, (ii) a turbine generally produces more power under the in-wake scenario than under the out-of-wake scenario, (iii) the power generation is sensitive to turbulence intensity even when the wind speed is greater than the turbine rated speed, and (iv) there is relatively more uncertainty in the power generation under the in-wake scenario than under the out-of-wake scenario.

  4. A Low Cost Shading Analyzer and Site Evaluator Design to Determine Solar Power System Installation Area

    Directory of Open Access Journals (Sweden)

    Selami Kesler

    2015-01-01

    Full Text Available Shading analyzer systems are necessary for selecting the most suitable installation site to sustain enough solar power. Afterwards, changes in solar data throughout the year must be evaluated along with the identification of obstructions surrounding the installation site in order to analyze shading effects on productivity of the solar power system. In this study, the shading analysis tools are introduced briefly, and a new and different device is developed and explained to analyze shading effect of the environmental obstruction on the site on which the solar power system will be established. Thus, exposure duration of the PV panels to the sunlight can be measured effectively. The device is explained with an application on the installation area selected as a pilot site, Denizli, in Turkey.

  5. Vector and tensor analyzing powers in deuteron-proton breakup reaction

    International Nuclear Information System (INIS)

    High precision data for vector and tensor analyzing powers of the 1H( d-vector ,pp)n breakup reaction at 130 and 100 MeV deuteron beam energies have been measured in a large fraction of the phase space. They are compared to the theoretical predictions based on various approaches to describe the three nucleon (3N) system dynamics. Theoretical predictions describe very well the vector analyzing power data, with no need to include any three-nucleon force effects for these observables. Tensor analyzing powers can be also very well reproduced by calculations in most of the studied region, but locally certain discrepancies are observed. At 130 MeV for Axy such discrepancies usually appear, or are enhanced, when model 3N forces are included. Predicted effects of 3NFs are much lower at 100 MeV and at this energy equally good consistency between the data and the calculations is obtained with or without 3NFs.

  6. Analyzing the Impact of Solar Power on Multi-Hourly Thermal Generator Ramping

    Energy Technology Data Exchange (ETDEWEB)

    Rosenkranz, Joshua-Benedict; Brancucci Martinez-Anido, Carlo; Hodge, Bri-Mathias

    2016-04-08

    Solar power generation, unlike conventional forms of electricity generation, has higher variability and uncertainty in its output because solar plant output is strongly impacted by weather. As the penetration rate of solar capacity increases, grid operators are increasingly concerned about accommodating the increased variability and uncertainty that solar power provides. This paper illustrates the impacts of increasing solar power penetration on the ramping of conventional electricity generators by simulating the operation of the Independent System Operator -- New England power system. A production cost model was used to simulate the power system under five different scenarios, one without solar power and four with increasing solar power penetrations up to 18%, in terms of annual energy. The impact of solar power is analyzed on six different temporal intervals, including hourly and multi-hourly (2- to 6-hour) ramping. The results show how the integration of solar power increases the 1- to 6-hour ramping events of the net load (electric load minus solar power). The study also analyzes the impact of solar power on the distribution of multi-hourly ramping events of fossil-fueled generators and shows increasing 1- to 6-hour ramping events for all different generators. Generators with higher ramp rates such as gas and oil turbine and internal combustion engine generators increased their ramping events by 200% to 280%. For other generator types--including gas combined-cycle generators, coal steam turbine generators, and gas and oil steam turbine generators--more and higher ramping events occurred as well for higher solar power penetration levels.

  7. Proton--proton analyzing power measurements at 16 MeV

    International Nuclear Information System (INIS)

    Few attempts have been made to measure accurately the proton-proton analyzing powers at low energies. With the advent of polarized particle beams the measurement can now be made with high accuracy. Analyzing powers were measured at nine scattering angles from 100 to 350 in the laboratory system. As a check on systematic errors, analyzing power measurements were also made by scattering protons from 4He. In the p Vector-p case the measured values are in very good agreement with the phase shift predictions. The p Vector-4He measurements, while giving the same form and sign as the phase shift predictions, differ from the predictions by as much as 11 standard deviations. The p Vector-p analyzing powers had a maximum value of -0.0043 +- 0.0004 at 100 (laboratory) and decreased to zero near 250. A new technique to measure analyzing powers without symmetric detectors is explained. This technique preserves the advantages of the symmetric arm method in that current integration, target density, detector efficiencies, and geometry are cancelled from the final expressions. A new scattering chamber, named the Supercube, is described. The Supercube was designed primarily to perform scattering experiments with a polarized beam. It contains both left-right and up-down detectors for use with both spin-1/2 and spin-1 measurements. The Supercube was designed to make analyzing power measurements to an accuracy of 0.001 routine. The Supercube has proved to have low systematic errors and to perform as expected. The systematic errors were found to be equal to or less than 0.0002. (23 figures, 14 tables) (auth)

  8. Time-reversal asymmetry: polarization and analyzing power in nuclear reactions

    International Nuclear Information System (INIS)

    Measurements of the proton polarization in the reactions 7Li(3He, p vector)9Be and 9Be(3He, p vector)11B and of the analyzing powers in the inverse reactions, initiated by polarized protons at the same center-of-mass energies, show significant differences. This implies the failure of the polarization-analyzing-power theorem and, prima facie, of time-reversal invariance in these reactions. The reaction 2H(3He, p vector)4He and its inverse have also been investigated and show smaller differences. A discussion of instrumental asymmetries is presented

  9. Using EPSAT to analyze high power systems in the space environment. [Environment Power System Analysis Tool

    Science.gov (United States)

    Kuharski, Robert A.; Jongeward, Gary A.; Wilcox, Katherine G.; Rankin, Tom R.; Roche, James C.

    1991-01-01

    The authors review the Environment Power System Analysis Tool (EPSAT) design and demonstrate its capabilities by using it to address some questions that arose in designing the SPEAR III experiment. It is shown that that the rocket body cannot be driven to large positive voltages under the constraints of this experiment. Hence, attempts to measure the effects of a highly positive rocket body in the plasma environment should not be made in this experiment. It is determined that a hollow cathode will need to draw only about 50 mA to ground the rocket body. It is shown that a relatively small amount of gas needs to be released to induce a bulk breakdown near the rocket body, and this gas release should not discharge the sphere. Therefore, the experiment provides an excellent opportunity to study the neutralization of a differential charge.

  10. Analyzing power measurements in πd elastic scattering at 50 MeV

    International Nuclear Information System (INIS)

    Measurements of the vector analyzing power in πd elastic scattering at 50 MeV are found to agree well with model calculations that include the full πN P11 potential and disagree when this is omitted or suppressed

  11. Unique electron polarimeter analyzing power comparison and precision spin-based energy measurement

    International Nuclear Information System (INIS)

    Precision measurements of the relative analyzing powers of five electron beam polarimeters, based on Compton, Moller, and Mott scattering, have been performed using the CEBAF accelerator at the Thomas Jefferson National Accelerator Facility (Jefferson Laboratory). A Wien filter in the 100 keV beamline of the injector was used to vary the electron spin orientation exiting the injector. High statistical precision measurements of the scattering asymmetry as a function of the spin orientation were made with each polarimeter. Since each polarimeter receives beam with the same magnitude of polarization, these asymmetry measurements permit a high statistical precision comparison of the relative analyzing powers of the five polarimeters. This is the first time a precise comparison of the analyzing powers of Compton, Moller, and Mott scattering polarimeters has been made. Statistically significant disagreements among the values of the beam polarization calculated from the asymmetry measurements made with each polarimeter reveal either errors in the values of the analyzing power, or failure to correctly include all systematic effects. The measurements reported here represent a first step toward understanding the systematic effects of these electron polarimeters. Such studies are necessary to realize high absolute accuracy (ca. 1%) electron polarization measurements, as required for some parity violation measurements planned at Jefferson Laboratory. Finally, a comparison of the value of the spin orientation exiting the injector that provides maximum longitudinal polarization in each experimental hall leads to an independent and very precise (better than 10-4) absolute measurement of the final electron beam energy

  12. Finite-range DWBA analysis of anomalous analyzing powers in (p, alpha) reactions

    International Nuclear Information System (INIS)

    Anomalous analyzing powers in reactions Ni(p vector, α)Co(3/2+) are studied in the framework of distorted-waves Born approximation. The anomaly is well reproduced by calculations based on the form factors and spectroscopic amplitudes which are derived from microscopic model wave functions. (author)

  13. Unique electron polarimeter analyzing power comparison and precision spin-based energy measurement

    Energy Technology Data Exchange (ETDEWEB)

    Joseph Grames; Charles Sinclair; Joseph Mitchell; Eugene Chudakov; Howard Fenker; Arne Freyberger; Douglas Higinbotham; B. Poelker; Michael Steigerwald; Michael Tiefenback; Christian Cavata; Stephanie Escoffier; Frederic Marie; Thierry Pussieux; Pascal Vernin; Samuel Danagoulian; Kahanawita Dharmawardane; Renee Fatemi; Kyungseon Joo; Markus Zeier; Viktor Gorbenko; Rakhsha Nasseripour; Brian Raue; Riad Suleiman; Benedikt Zihlmann

    2004-03-01

    Precision measurements of the relative analyzing powers of five electron beam polarimeters, based on Compton, Moller, and Mott scattering, have been performed using the CEBAF accelerator at the Thomas Jefferson National Accelerator Facility (Jefferson Laboratory). A Wien filter in the 100 keV beamline of the injector was used to vary the electron spin orientation exiting the injector. High statistical precision measurements of the scattering asymmetry as a function of the spin orientation were made with each polarimeter. Since each polarimeter receives beam with the same magnitude of polarization, these asymmetry measurements permit a high statistical precision comparison of the relative analyzing powers of the five polarimeters. This is the first time a precise comparison of the analyzing powers of Compton, Moller, and Mott scattering polarimeters has been made. Statistically significant disagreements among the values of the beam polarization calculated from the asymmetry measurements made with each polarimeter reveal either errors in the values of the analyzing power, or failure to correctly include all systematic effects. The measurements reported here represent a first step toward understanding the systematic effects of these electron polarimeters. Such studies are necessary to realize high absolute accuracy (ca. 1%) electron polarization measurements, as required for some parity violation measurements planned at Jefferson Laboratory. Finally, a comparison of the value of the spin orientation exiting the injector that provides maximum longitudinal polarization in each experimental hall leads to an independent and very precise (better than 10-4) absolute measurement of the final electron beam energy.

  14. Analyzing power measurements in πd elastic scattering at 50 MeV

    International Nuclear Information System (INIS)

    Measurements of the vector analyzing power in πd elastic scattering at 50 MeV are found to agree well with model calculations that include the full πN P11 potential and disagree when this is omitted or suppressed. (Author) (10 refs., 3 figs.)

  15. First measurement of the vector analyzing power in muon capture by polarized muonic 3He

    International Nuclear Information System (INIS)

    This paper describes the first measurement of spin observables in nuclear muon capture by 3He. The sensitivity of spin observables to the pseudoscalar coupling is described. The triton asymmetry presented has to be corrected for small systematic effects in order to extract the vector analyzing power. The analysis of these effects is currently underway

  16. Analyzing powers of the deuteron-proton breakup in a wide phase space region

    International Nuclear Information System (INIS)

    Deuteron-proton breakup can serve as a very rich testing ground for modern calculations based on model nucleon-nucleon interactions and including also subtle effects of the so-called three-nucleon force (3NF). In the case of experiment exploring a significant part of the phase space, data obtained for continuum of final states constitute a large base for comparisons with theoretical predictions. Moreover, studies with transversally polarized deuterons give access to two vector and three tensor analyzing powers, some of which vanish in the case of the elastic scattering process. A dedicated experiment has been performed at KVI Groningen, with the use of 130 MeV polarized deuteron beam and high acceptance position-sensitive detection system. About 800 data points have been analyzed for each spin observable: vector Ax, Ay and tensor Axx, Axy, Ayy analyzing powers of the 1H(vector (d),pp)n breakup reaction. Theoretical predictions generally describe analyzing power data quite well and the quality of description provided by various approaches is rather similar. There are, however, configurations where the agreement between the data and theory is not so satisfactory. These discrepancies are not always cured by inclusion of 3NF, what indicates incompleteness of the treatment of the spin part of three nucleon system dynamics.

  17. Real time voltage and current phase shift analyzer for power saving applications.

    Science.gov (United States)

    Krejcar, Ondrej; Frischer, Robert

    2012-01-01

    Nowadays, high importance is given to low energy devices (such as refrigerators, deep-freezers, washing machines, pumps, etc.) that are able to produce reactive power in power lines which can be optimized (reduced). Reactive power is the main component which overloads power lines and brings excessive thermal stress to conductors. If the reactive power is optimized, it can significantly lower the electricity consumption (from 10 to 30%-varies between countries). This paper will examine and discuss the development of a measuring device for analyzing reactive power. However, the main problem is the precise real time measurement of the input and output voltage and current. Such quality measurement is needed to allow adequate action intervention (feedback which reduces or fully compensates reactive power). Several other issues, such as the accuracy and measurement speed, must be examined while designing this device. The price and the size of the final product need to remain low as they are the two important parameters of this solution. PMID:23112662

  18. The spin correlation parameter and analyzing power in n-p elastic scattering at intermediate energies

    International Nuclear Information System (INIS)

    In order to improve existing I=0 phase shift solutions, the spin correlation parameter, ANN, and the analyzing powers, A0N and AN0, have been measured in n-p elastic scattering over an angular range of 50 degrees -150 degrees (c.m.) at three neutron energies, 220, 325 and 425 MeV to an absolute accuracy of ±0.03. The data have a profound effect on various phase parameters, particularly the 1P1, 3D2 and ε1 phase parameters which in some cases change by almost a degree. With exception of the highest energy, the data support the predictions of the latest version of the Bonn potential. Also the analyzing power data (A0N and AN0) measured at 477 MeV in a different experiment over a limited angular range (60 degrees - 80 degrees (c.m.)) are reported here. (Author) 30 refs., 10 figs., 5 tabs

  19. Development of a CGE model for analyzing the role of nuclear power in sustainable growth

    International Nuclear Information System (INIS)

    The purpose of this study is to develop the model for analyzing the role of nuclear power in the sustainable energy supply future of Korea. For the purpose, an energy-economy interaction model of the computational general equilibrium (CGE) approach was developed. The model is a standard optimization model that maximizes the discounted value of Korean economic utility. The model developed in this study can be contributed to setup the national energy policy

  20. Tensor Analyzing Powers for Quasi-Elastic Electron Scattering from Deuterium

    Energy Technology Data Exchange (ETDEWEB)

    Z.-L. Zhou; M. Bouwhuis; M. Ferro-Luzzi; E. Passchier; R. Alarcon; M. Anghinolfi; H. Arenhoevel; R. van Bommel; T. Botto; J.F.J. van den Brand; H.J. Bulten; S. Choi; J. Comfort; S.M. Dolfini; R. Ent; C. Gaulard; D.W. Higinbotham; C.W. de Ja ger; E. Konstantinov; J. Lang; W. Leidemann; D.J. de Lange; M.A. Miller; D. Niko lenko; N. Papadakis; I. Passchier; H.R. Poolman; S.G. Popov; I. Rachek; M. Ripan i; E. Six; J.J.M. Steijger; M. Taiuti; O. Unal; N. Vodinas; H. de Vries

    1999-01-01

    We report on a first measurement of tensor analyzing powers in quasi-elastic electron-deuteron scattering at an average three-momentum transfer of 1.7 fm{sup -1}. Data sensitive to the spin-dependent nucleon density in the deuteron were obtained for missing momenta up to 150 MeV/c with a tensor polarized {sup 2}H target internal to an electron storage ring. The data are well described by a calculation that includes the effects of final-state interaction, meson-exchange and isobar currents, and leading-order relativistic contributions.

  1. Analyzing-power measurements for the 3He(t,d)4He reaction

    International Nuclear Information System (INIS)

    We report analyzing-power angular distributions for the 3He(t,d)4He reaction at bombarding energies of 9.02, 12.86, and 17.02 MeV, and an excitation function at 900 c.m. from 9.02 to 17.27 MeV. The angular distributions show marked deviations from the antisymmetric shape predicted by a simple particle-transfer model incorporating charge symmetry. Reaction mechanisms and violations of charge symmetry which might account for the data are discussed

  2. The tensor analyzing power Asub(yy) near s-wave levels

    International Nuclear Information System (INIS)

    In the neighborhood of an isolated resonance induced by s-wave particles, the component Asub(yy)(theta) of the tensor analyzing power is independent of the reaction angle theta. The constant value of Asub(yy)(theta) is a function of the level spin J and of the (l',s') configuration in the exit channel of the resonant amplitude. The use of this fact as a diagnostic tool in an analysis of the process is discussed and demonstrated with data available. It is also pointed out that efficient polarimeters can be constructed, which measure the quantity Asub(yy). (Auth.)

  3. Proton-proton elastic scattering excitation functions at intermediate energies: Cross sections and analyzing powers

    International Nuclear Information System (INIS)

    The EDDA experiment at the cooler synchrotron COSY measures proton-proton elastic scattering excitation functions in the momentum range 0.8 - 3.4 GeV/c. In phase 1 of the experiment, spin-averaged differential cross sections were measured continuously during acceleration with an internal polypropylene (CH2) fiber target, taking particular care to monitor luminosity as a function of beam momentum. In phase 2, excitation functions of the analyzing power AN and the polarization correlation parameters ANN, ASS and ASL are measured using a polarized proton beam and a polarized atomic hydrogen beam target. The paper presents recent dσ/dΩ and AN data. The results provide excitation functions and angular distributions of high precision and internal consistency. No evidence for narrow structures was found. The data are compared to recent phase shift solutions

  4. MEASUREMENT OF THE ANALYZING POWER IN PP ELASTIC SCATTERING IN THE PEAK CNI REGION AT RHIC.

    Energy Technology Data Exchange (ETDEWEB)

    MAKDISI,Y.; OKADA,H.; ALEKSEEV,I.G.; BRAVAR,A.; BUNCE,G.; ET AL

    2005-01-28

    The analyzing power A{sub N} for pp elastic scattering is expected to reach a peak value of 0.045 in the Coulomb Nuclear Interference (CNI) region at a momentum transfer -t of 0.003 (GeV/c){sup 2}. During the 2004 RHIC Run, we completed a measurement of A{sub N} in the CNI region by detecting the recoil protons from pp elastic scattering using a polarized atomic hydrogen gas jet target and the 100 GeV RHIC proton beam. We report the first measurements of the A{sub N} absolute value and shape in the -t range from 0.0015 to 0.010 (GeV/c){sup 2} with a precision better than 0.005 for each A{sub N} data point. The recoil protons were detected with two arrays of Si detectors. The absolute target polarization as monitored by a Breit-Rabi polarimeter was stable at 0.924 {+-} 0.018. This result allows us to further investigate the spin dependence of elastic pp scattering in the very low -t region.

  5. Analyzing power in CNI-region at AGS (experiment E950)

    International Nuclear Information System (INIS)

    Acceleration of polarized protons is one of the exciting features of the new Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory. Measurements of beam polarization are required both for experiments and the accelerator tuning. Elastic scattering in the Coulomb nuclear interference (CNI) region of polarized proton beams on a carbon target demonstrates asymmetry which can be used to build a polarimeter. The methods proposed for a RHIC CNI polarimeter were tested with the AGS polarized beam in the E950 experiment. A 21.7 GeV/c polarized proton beam was scattered on an extremely thin carbon ribbon target located in the AGS ring. Two symmetrical arms consisting of silicon strip detectors (SSD) and a micro channel plate (MCP) were used to identify recoil carbon. Data obtained demonstrates a good identification of the reaction by the apparatus and a significant analyzing power. A RHIC polarimeter setup with 4 SSDs but without MCPs will be used to commission RHIC with polarized protons and for the first spin physics running in 2001

  6. Analyzing power of AGATA triple clusters for gamma-ray linear polarization

    Energy Technology Data Exchange (ETDEWEB)

    Bizzeti, P.G.; Sona, P.; Melon, B.; Bizzeti-Sona, A.M.; Perego, A. [Universita di Firenze, Dipartimento di Fisica, Firenze (Italy); INFN, Firenze (Italy); Michelagnoli, C.; Lunardi, S.; Mengoni, D.; Recchia, F. [INFN, Padova (Italy); Universita di Padova, Dipartimento di Fisica, Padova (Italy); Bazzacco, D.; Farnea, E.; Menegazzo, R.; Ur, C.A. [INFN, Padova (Italy); De Angelis, G.; Gottardo, A.; Napoli, D.R.; Sahin, E.; Valiente-Dobon, J.J. [Laboratori Nazionali di Legnaro, INFN, Padova (Italy); Gadea, A. [University of Valencia, IFIC, CSIC, Valencia (Spain); Nannini, A. [INFN, Firenze (Italy)

    2015-04-01

    We have investigated the ability of AGATA triple clusters to measure the linear polarization of gamma rays, exploiting the azimuthal-angle dependence of the Compton scattering differential cross section. To this aim, partially polarized gamma rays have been produced by Coulomb excitation of the first excited state of {sup 104}Pd and {sup 108}Pd, which decay to the ground state by emission of gamma rays of 555.8 keV and 433.9 keV, respectively. Pulse-shape analysis and gamma-ray tracking techniques have been used to determine the position and time sequence of the interaction points inside the germanium crystals. Anisotropies in the detection efficiency have been taken into account using 661.6 keV gammas from a {sup 137}Cs radioactive source. We obtain an average analyzing power of 0.451(34) at 433.9 keV and 0.484(24) at 555.8 keV. (orig.)

  7. Diagnosis of power generator sets by analyzing the crank shaft angular speed

    International Nuclear Information System (INIS)

    This thesis deals with the diagnosis of a powerful 20-cylinder diesel engine which runs a generator set in a nuclear plant. The objective is to make a diagnosis by analyzing the crank shaft angular speed variations. Only combustion related faults are investigated. As the engine is very large, the first crank shaft natural modes are in the low frequencies. Torsional vibrations of the flexible crank shaft strongly complicate the analysis of the angular speed variations. Little attention has been paid to such large engines in the literature. First, a dynamical model with the assumption of a flexible crank shaft is established. The parameters of the model are optimized with the help of actual data. Then, an original automated diagnosis based on pattern recognition of the angular speed waveforms is proposed. Indeed, any faulty cylinder in combustion stroke will distort the angular speed waveform in a specific way which depends on its location with respect to nodes and anti-nodes of the modes. Reference patterns, representative of the engine conditions, are computed with the model constituting the main originality of this work. Promising results are obtained in operational phase. An experimental fuel leakage fault was correctly diagnosed, including detection and localization of the faulty cylinder and an indication of the severity of the fault. (author)

  8. Analyzing Thermal Module Developments and Trends in High-Power LED

    Directory of Open Access Journals (Sweden)

    Jung-Chang Wang

    2014-01-01

    Full Text Available The solid-state light emitting diode (SSLED has been verified as consumer-electronic products and attracts attention to indoor and outdoor lighting lamp, which has a great benefit in saving energy and environmental protection. However, LED junction temperature will influence the luminous efficiency, spectral color, life cycle, and stability. This study utilizes thermal performance experiments with the illumination-analysis method and window program (vapour chamber thermal module, VCTM V1.0 to investigate and analyze the high-power LED (Hi-LED lighting thermal module, in order to achieve the best solution of the fin parameters under the natural convection. The computing core of the VCTM program employs the theoretical thermal resistance analytical approach with iterative convergence stated in this study to obtain a numerical solution. Results showed that the best geometry of thermal module is 4.4 mm fin thickness, 9.4 mm fin pitch, and 37 mm fin height with the LED junction temperature of 58.8°C. And the experimental thermal resistances are in good agreement with the theoretical thermal resistances; calculating error between measured data and simulation results is no more than ±7%. Thus, the Hi-LED illumination lamp has high life cycle and reliability.

  9. Life Cycle Assessment of a HYSOL Concentrated Solar Power Plant: Analyzing the Effect of Geographic Location

    OpenAIRE

    Corona Bellostas, Blanca; Ruiz, Diego; San Miguel Alfaro, Guillermo

    2016-01-01

    Concentrating Solar Power (CSP) technology is developing in order to achieve higher energy efficiency, reduced economic costs, and improved firmness and dispatchability in the generation of power on demand. To this purpose, a research project titled HYSOL has developed a new power plant, consisting of a combined cycle configuration with a 100 MWe steam turbine and an 80 MWe gas-fed turbine with biomethane. Technological developments must be supported by the identification, quantification, and...

  10. Analyzing Non-Functional Capabilities of ICT Infrastructures Supporting Power System Wide Area Monitoring and Control

    OpenAIRE

    Chenine, Moustafa

    2013-01-01

    The strain on modern electrical power systems has led to an ever-increasing utilization of new information and communication technologies (ICT) to improve their efficiency and reliability. Wide area monitoring and control (WAMC) systems offer many opportunities to improve the real-time situational awareness in the power system. These systems are essen-tially SCADA systems but with continuous streaming of measurement data from the power system. The quality of WAMC systems and the applications ...

  11. Analyzing powers Ayy, Axx, Axz and Ay in the dd→3Hen reaction at 270 MeV

    International Nuclear Information System (INIS)

    The data on the tensor Ayy, Axx, Axz and vector Ay analyzing powers in the dd→3Hen reaction obtained at Td=270 MeV in the angular range 0-110 deg in the c.m. are presented. The observed negative sign of the tensor analyzing powers Ayy, Axx and Axz at small angles clearly demonstrates the sensitivity to the ratio of the D- and S-wave component of the 3He wave function. However, the one-nucleon exchange calculations by using the standard 3He wave functions have failed to reproduce the strong variation of the tensor analyzing powers as a function of the angle in the c.m

  12. Modeling and analyzing of nuclear power peer review on enterprise operational efficiency

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Based on the practice and analysis of peer review in nuclear power plants, the models on the Pareto improvement of peer review, governance entropy decrease of peer review are set up and discussed. The result shows that the peer review of nuclear power is actually a process of Pareto improvement, and of governance entropy decrease. It's a process of improvement of the enterprise operational efficiency accordingly.

  13. Analyzing the effects of component reliability on naval integrated power system quality of service

    OpenAIRE

    Hawbaker, Benjamin F.

    2008-01-01

    CIVINS The Integrated Power System (IPS) is a key enabling technology for future naval vessels and their advanced weapon systems. While conventional warship designs utilize separate power systems for propulsion and shipboard electrical service, the IPS combines these functions. This allows greater optimization of engineering plant design and operations and leads to significant potential lifecycle cost savings through reduced fuel consumption and maintenance. Traditionally the focus of powe...

  14. Decarbonizing Europe's power sector by 2050 — Analyzing the economic implications of alternative decarbonization pathways

    International Nuclear Information System (INIS)

    The European Union aims to reduce greenhouse gas emissions by 80–95% in 2050 compared to 1990 levels. The transition towards a low-carbon economy implies the almost complete decarbonization of Europe's power sector, which could be achieved along various pathways. In this paper, we evaluate the economic implications of alternative energy policies for Europe's power sector by applying a linear dynamic electricity system optimization model in over 36 scenarios. We find that the costs of decarbonizing Europe's power sector by 2050 vary between 139 and 633 bn €2010, which corresponds to an increase of between 11% and 44% compared to the total system costs when no CO2 reduction targets are implemented. In line with economic theory, the decarbonization of Europe's power sector is achieved at minimal costs under a stand-alone CO2 reduction target, which ensures competition between all low-carbon technologies. If, however, renewable energies are exempted from competition via supplementary renewable energy (RES-E) targets or if investments in new nuclear and CCS power plants are politically restricted, the costs of decarbonization significantly rise. Moreover, we find that the excess costs of supplementary RES-E targets depend on the acceptance of alternative low carbon technologies. For example, given a complete nuclear phase-out in Europe by 2050 and politically implemented restrictions on the application of CCS to conventional power plants, supplementary RES-E targets are redundant. While in such a scenario the overall costs of decarbonization are comparatively high, the excess costs of supplementary RES-E targets are close to zero. - Highlights: • We evaluate the economic implications of alternative energy policies for Europe's power sector. • Total decarbonization costs vary between 139 and 633 billion €2010 up to 2050. • Decarbonization at minimal costs is ensured by competition between all low carbon technologies. • Excess costs of supplementary

  15. Analyze and Improve Lifetime in 3L-NPC Inverter from Power Cycle and Thermal Balance

    DEFF Research Database (Denmark)

    Chen, Quan; Chen, Zhe; Wang, Qunjing;

    2014-01-01

    load voltage is applied to reduce power cycle and switching losses. And then, three-level active neutral point-clamped topology is taken into account to wake the most thermo stressed device. In order to validate the improve lifetime method in this paper, a 2MW 3L-NPC converter used in wind energy has......Three-level Neutral-point-clamped (3L-NPC) topology is becoming a realistic alternative to the conventional one in high-voltage and high-power application. Studies show that the power cycling mean time to failure (MTTF) of the semiconductor bond wire in 3L-NPC inverter system may be very short...

  16. Analyzing Potential Grid Impacts from Future In-Motion Roadway Wireless Power Transfer Scenarios: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Meintz, Andrew; Gonder, Jeffrey; Jorgenson, Jennie; Brooker, Aaron

    2016-08-01

    This work examines the grid impact of in-motion roadway wireless power transfer through the examination of the electrification of high-capacity roadways inside a metropolitan area. The work uses data from a regional travel study and the Federal Highway Administration's Highway Performance Monitoring System to estimate the electrified roadway's hourly power use throughout a week. The data are then combined with hourly grid load estimates for the same metropolitan area to determine the overlay of traditional grid load with additional load from a future electrified roadway.

  17. Fuel-Cell-Powered Electric Motor Drive Analyzed for a Large Airplane

    Science.gov (United States)

    Brown, Gerald V.; Choi, Benjamin B.

    2005-01-01

    Because of its high efficiency, fuel cell technology may be used to launch a new generation of more-electric aeropropulsion and power systems for future aircraft. Electric-motor-driven airplanes using fuel-cell powerplants would be beneficial to the environment because of fuel savings, low noise, and zero carbon-dioxide emissions. In spite of the fuel cell s efficiency benefit, to produce the same shaft drive power, a fuel cell- powered electric-drive system must be definitely heavier than a turbine-drive system. However, the fuel-cell system s overall efficiency from fuel-to-shaft power is higher than for a turbine-drive system. This means that the fuel consumption rate could be lower than for a conventional system. For heavier, fuel-laden planes for longer flights, we might achieve substantial fuel savings. In the airplane industry, in fact, an efficiency gain of even a few percentage points can make a major economic difference in operating costs.

  18. Assessment method for analyzing and developing human resource management practices in the nuclear power industry

    International Nuclear Information System (INIS)

    Implementation of HRM practices is often devolved from the HRM unit to front line managers and supervisors. However, the implementation of these practices by line managers and supervisors may vary significantly. They may, for example, be unaware of how to implement HRM practices or sceptical towards the effectiveness of the intended practices. Based on the literature, interviews and workshops in the nuclear power industry, a self-assessment method of HRM practices for intra-organizational use was developed. The assessment method was piloted in four nuclear power organizations. The assessment method seems to be a good tool for generating fruitful discussion on HRM practices, finding areas of HRM practices that need to be developed, and triggering peer-to-peer knowledge sharing and learning on HRM practices.

  19. Assessment method for analyzing and developing human resource management practices in the nuclear power industry

    Energy Technology Data Exchange (ETDEWEB)

    Maeki, Eerikki [Aalto Univ. (Finland). Dept. of Industrial Engineering and Management; Pahkin, Krista; Lindstroem, S.; Kurki, Anna-Leena [Finnish Institue of Occupational Health, Helsinki (Finland). Centre of Expertise for the Development of Work and Organizations

    2015-04-15

    Implementation of HRM practices is often devolved from the HRM unit to front line managers and supervisors. However, the implementation of these practices by line managers and supervisors may vary significantly. They may, for example, be unaware of how to implement HRM practices or sceptical towards the effectiveness of the intended practices. Based on the literature, interviews and workshops in the nuclear power industry, a self-assessment method of HRM practices for intra-organizational use was developed. The assessment method was piloted in four nuclear power organizations. The assessment method seems to be a good tool for generating fruitful discussion on HRM practices, finding areas of HRM practices that need to be developed, and triggering peer-to-peer knowledge sharing and learning on HRM practices.

  20. Analyzing the Impacts of Increased Wind Power on Generation Revenue Sufficiency: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Qin; Wu, Hongyu; Tan, Jin; Hodge, Bri-Mathias; Li, Wanning; Luo, Cheng

    2016-08-01

    The Revenue Sufficiency Guarantee (RSG), as part of make-whole (or uplift) payments in electricity markets, is designed to recover the generation resources' offer-based production costs that are not otherwise covered by their market revenues. Increased penetrations of wind power will bring significant impacts to the RSG payments in the markets. However, literature related to this topic is sparse. This paper first reviews the industrial practices of implementing RSG in major U.S. independent system operators (ISOs) and regional transmission operators (RTOs) and then develops a general RSG calculation method. Finally, an 18-bus test system is adopted to demonstrate the impacts of increased wind power on RSG payments.

  1. Assessment method for analyzing and developing human resource management practices in nuclear power industry

    International Nuclear Information System (INIS)

    Implementation of HRM practices is often devolved from the HRM unit to front line managers and supervisors. However, the implementation of these practices by line managers and supervisors may vary significantly. They may, for example, be unaware of how to implement HRM practices or skeptical towards the effectiveness of the intended practices. Based on the literature, interviews and workshops in the nuclear power industry, a self-assessment method of HRM practices for intra-organizational use was developed. The assessment method was piloted in four nuclear power organizations. The assessment method seems to be a good tool for generating fruitful discussion on HRM practices, finding areas of HRM practices that need to be developed, and triggering peer-to-peer knowledge sharing and learning on HRM practices. (authors)

  2. Analyzing the power of classes in an object-oriented software system

    Science.gov (United States)

    Wang, Muchou

    2011-10-01

    Power of a class reflects the relative importance of the class in an object-oriented software system, and has many implications for resource allocating. And how to measure it is still a problem we face. They paper presents to measure it based the connection structure of a network constructed from the software. To support this, we first use a network model to describe the connection structure. Then some centrality metrics used in social network analysis are introduced to quantify the power of classes. The commons and differences among these centrality metrics are revealed. We think these metrics can be used together to have a more systematic view of the importance of each class.

  3. Life Cycle Assessment of a HYSOL Concentrated Solar Power Plant: Analyzing the Effect of Geographic Location

    Directory of Open Access Journals (Sweden)

    Blanca Corona

    2016-05-01

    Full Text Available Concentrating Solar Power (CSP technology is developing in order to achieve higher energy efficiency, reduced economic costs, and improved firmness and dispatchability in the generation of power on demand. To this purpose, a research project titled HYSOL has developed a new power plant, consisting of a combined cycle configuration with a 100 MWe steam turbine and an 80 MWe gas-fed turbine with biomethane. Technological developments must be supported by the identification, quantification, and evaluation of the environmental impacts produced. The aim of this paper is to evaluate the environmental performance of a CSP plant based on HYSOL technology using a Life Cycle Assessment (LCA methodology while considering different locations. The scenarios investigated include different geographic locations (Spain, Chile, Kingdom of Saudi Arabia, Mexico, and South Africa, an alternative modelling procedure for biomethane, and the use of natural gas as an alternative fuel. Results indicate that the geographic location has a significant influence on the environmental profile of the HYSOL CSP plant. The results obtained for the HYSOL configuration located in different countries presented significant differences (between 35% and 43%, depending on the category, especially in climate change and water stress categories. The differences are mainly attributable to the local availability of solar and water resources and composition of the national electricity mix. In addition, HYSOL technology performs significantly better when hybridizing with biomethane instead of natural gas. This evidence is particularly relevant in the climate change category, where biomethane hybridization emits 27.9–45.9 kg CO2 eq per MWh (depending on the biomethane modelling scenario and natural gas scenario emits 264 kg CO2 eq/MWh.

  4. Analyzing the decision making process of certifying digital control systems of nuclear power plants

    International Nuclear Information System (INIS)

    Highlights: ► We have performed basic research in analyzing certification process and developed a regulatory decision making model for nuclear digital control system certification. The model views certification as an evidence–confidence conversion process. ► We have applied this model to analyze previous nuclear digital I and C certification experiences and obtained valuable insights. ► Furthermore, a prototype of a computer-aided licensing support system based on the model has been developed to enhance regulatory review efficiency. - Abstract: Safety-critical computing systems need regulators’ approval before operation. Such a permit issue process is called “certification”. Digital instrumentation and Control (I and C) certification in the nuclear domain has always been problematic and lengthy. Thus, the certification efficiency has always been a crucial concern to the applicant whose business depends on the regulatory decision. However, to our knowledge, there is little basic research on this topic. This study presents a Regulatory Decision-Making Model aiming at analyzing the characteristics and efficiency influence factors in a generic certification process. This model is developed from a dynamic operational perspective by viewing the certification process as an evidence–confidence conversion process. The proposed model is then applied to previous nuclear digital I and C certification experiences to successfully explain why some cases were successful and some were troublesome. Lessons learned from these cases provide invaluable insights regarding to the regulatory review activity. Furthermore, to utilize the insights obtained from the model, a prototype of a computer-aided licensing support system has been developed to speed up review evidence preparation and manipulation; thus, regulatory review efficiency can be further improved.

  5. A matrix game model for analyzing FTR bidding strategies in deregulated electric power markets

    International Nuclear Information System (INIS)

    Suppliers in deregulated electric power markets compete for financial transmission rights (FTRs) to hedge against congestion charges. The system operator receives the bids for FTRs submitted by the suppliers and develops an allocation strategy by solving an optimization model. Each FTR bid is defined by a path, a quantity indicating the amount of FTRs the supplier is bidding for in that path, and the price that the supplier is willing to pay for each FTR. The FTR revenue is calculated only after the electricity market has been cleared by computing the differences in the LMPs at the pair of nodes that connect each path. Thus, suppliers rely on forecasts of locational marginal prices (LMPs) to develop their FTR bids. In this paper, we present a game theoretic modeling approach to develop FTR bidding strategies for power suppliers assuming that they have forecasts of LMPs. The game theoretic model considers multiple participants as well as network contingencies. We apply the game theoretic model on a sample network to assess impacts of variations of bid and network parameters on the FTR market outcome. (author)

  6. Development of the nuclear plant analyzer for Korean standard Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Shin Hwan; Kim, Hyeong Heon; Song, In Ho; Hong, Eon Yeong; Oh, Yeong Taek [Korea Power Engineering Company Inc., Yongin (Korea, Republic of)

    2000-12-15

    The purpose of this study is to develop an NPA for the Ulchin Nuclear Power Plant Unit 3 and 4, the first KSNP type plant. In this study, the process model simulating the overall plant systems, GUI and simulation executive which provide the functions of an engineering simulator were developed, and the NPA was completed by integrating them. The contents and the scope of this study are as follows : main feedwater system, auxiliary feedwater system, Chemical and Volume Control System(CVCS), Safety Injection System(SIS), Shutdown Cooling System(SCS), electric power supply system, Core Protection Calculator(CPC), various plant control system, development of the graphics screens for each system, real-time simulation, simulation control for the enhancement of functional capabilities, user friendly GUI, collection of the design and operating data, establishment of the NPA database, integration of the GUI and simulation control program with process model, collection of the data for the verification and validation of the developed NPA, collection of the plant test data, collection and review of the results of other computer codes, verification of the simulation accuracy by comparing the NPA results with the actual plant data, validation of the simulation capability of the NPA, comparison against available data from other analysis suing different computer codes.

  7. A computational system for analyze nuclear power plants structures, made by panels, using superelements

    International Nuclear Information System (INIS)

    The analysis of linear static behavior of folded-plate structures like the turbine building of a nuclear power plant by the Finite Element Method. Folded-plate isoparametric plane elements with 48 degrees of freedom each, 8 nodal points, in which shear deformations are considered, and super-elements, whose internal degrees of freedom are condensated, are used. Arbitrary shells can be analized too. A brief exposition of the method is present and the developing of the foregoing element and super-element is also shown. A computer program was developed for the CDC-CYBER 175 computer machine and the FORTRAN IV language was used. The coeficients of the equations system are stored by the technique of block partitioning with a compacted column storage scheme and special attention was dedicated to the preparation of the problem's data and some options were developed for this purpose. (Author)

  8. A Method for Analyzing the Communications among Nuclear Power Plant Operators in Emergency Situations

    International Nuclear Information System (INIS)

    Communications among MCR operators is an important factor for understanding how and how well MCR operators manage abnormal situations in NPPs. As mentioned by Ujita et al., the performance of MCR operators in emergency situations in NPPs is strongly affected by not only the cognitive process for each operator, but also by communications and collaboration among operators. Many researches have been conducted to find out the relation between the communication of human operators and the performance of them. But, it seems that few researches have been conducted on in what way the communication among MCR operators should be performed to enhance the performance of them. In this paper, we propose an analysis method for evaluating the quality of communications among MCR operators in nuclear power plants (NPPs)

  9. Methods for Analyzing the Economic Value of Concentrating Solar Power with Thermal Energy Storage

    Energy Technology Data Exchange (ETDEWEB)

    Denholm, Paul [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jorgenson, Jennie [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Miller, Mackay [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhou, Ella [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wang, Caixia [State Grid Energy Research Inst., Beijing (China)

    2015-07-20

    Concentrating solar power with thermal energy storage (CSP-TES) provides multiple quantifiable benefits compared to CSP without storage or to solar photovoltaic (PV) technology, including higher energy value, ancillary services value, and capacity value. This report describes modeling approaches to quantifying these benefits that have emerged through state-level policymaking in the United States as well as the potential applicability of these methods in China. The technical potential for CSP-TES in China is significant, but deployment has not yet achieved the targets established by the Chinese government. According to the 12th Five Year Plan for Renewable Energy (2011-2015), CSP was expected to reach 1 GW by 2015 and 3 GW by 2020 in China, yet as of December 2014, deployment totaled only 13.8 MW. One barrier to more rapid deployment is the lack of an incentive specific to CSP, such as a feed-in tariff. The 13th Five Year Plan for Solar Generation (2016-2020), which is under development, presents an opportunity to establish a feed-in tariff specific to CSP. This report, produced under the auspices of the U.S.-China Renewable Energy Partnership, aims to support the development of Chinese incentives that advance CSP deployment goals.

  10. Analyzing Powers of Inelastic dp-Scattering in the Energy Region of Delta and Roper Resonances Excitation

    CERN Document Server

    Malinina, L V; Augustyniak, W; Boivin, M; Boyard, J L; Dahl, R; Drews, M; Ellegaard, C; Fahri, L; Gaarde, C; Hennino, T; Jourdain, J C; Kagarlis, M A; Kravtsov, A V; Künne, R A; Larsen, J C; Morsch, P; Mylnikov, V A; Orichtchin, E M; Perdrisat, C F; Piskunov, N M; Prokofiev, A N; Punjabi, V; Radvanyi, P; Ramstein, B; Razmyslovich, B V; Roy-Stephan, M; Sitnik, I M; Skousen, M; Strokovsky, E A; Tkach, I I; Tomasi-Gustafsson, E; Volkov, S S; Zhdanov, A A; Zupranski, P

    2001-01-01

    A study of inelastic scattering of polarized 3.73 GeV/c deuterons on protons in the energy region of the Roper N*(1440) and the {DELTA}(1232) resonances excitation has been performed in an exclusive experiment at LNS (Laboratoire National SATURNE, Saclay, France) using the SPES-{pi} setup.Tensor and vector analyzing powers of pion production for the reactions d + p {\\to} d + n + pi^{+}, d + p {\\to} d + p + pi^{0}, d + p {\\to} d + N + pi pi have been measured as functions of the squared deuteron 4-momentum transfer t, of the effective mass of the subsystems (N pi), (N pi pi) and of the pion emission angle. A strong dependence of these analyzing powers upon the pion emission angle is observed. It is found that A_{yy} values for the considered reaction channels are systematically larger than the known inclusive {p (d, d {\\prime}) X} world data at the nearest beam energy.

  11. The tensor analyzing power T20 in deuteron break-up reactions within the Bethe-Salpeter formalism

    International Nuclear Information System (INIS)

    The deuteron tensor analyzing power T20 in the deuteron break-up reaction Dp → pX is calculated within a relativistic approach based on the Bethe-Salpeter equation with a realistic meson-exchange potential. Our results on T20 and the cross section are compared with experimental data and non-relativistic calculations and with the outcome of a relativization procedure of the deuteron wave function. (orig.)

  12. Complete Set of Deuteron Analyzing Powers for dp Elastic Scattering at 250 MeV/nucleon and Three Nucleon Forces

    Directory of Open Access Journals (Sweden)

    Shimizu Y.

    2010-04-01

    Full Text Available Measurements of a complete set of deuteron analyzing powers (iT11, T20, T21, T22 for elastic deuteron–proton scattering at 250 MeV/nucleon have been performed with polarized deuteron beams at RIKEN RI Beam Factory. The obtained data are compared with the Faddeev calculations based on the modern nucleon–nucleon forces together with the Tucson-Melbourne’99, and UrbanaIX three nucleon forces.

  13. The magnetic field near power lines in the Moscow region: the results of measurements and their analyze

    Directory of Open Access Journals (Sweden)

    Prokofyeva A.S.

    2014-12-01

    Full Text Available The aim: to analyze the real power frequency magnetic field (50 Hz values near power lines. The material. Long-term measurements of the power frequency magnetic field (50 Hz near power lines of 110 kV, 220 kVand 500 kVin the Moscow region. Methods. Measurements were made by tracks which were perpendicular to the wires. Length of tracks was up to 40 m. Sensor of measurer was located on 1.8 m under the ground. General quantity of measurement points were 1103. The results. Was obtained general characteristics of real values of strength of electric field and values of magnetic flux density depending to distance to the projection last wire near power lines. Conclusion. Analysis of the results has the values of the magnetic field of power lines correspond to the Russian rules in all cases. Using additional World Health Organization safety criteria for magnetic fields (the class of carcinogenic risks 2B requires the expansion of the health safety zone 2-3 times.

  14. Vector analyzing power iT11 in πd elastic scattering at 49 MeV

    International Nuclear Information System (INIS)

    Measurements of the vector analyzing power iT11 in πd elastic scattering at 49 MeV have been performed using a dynamically polarized target and a magnetic spectrometer. Data at seven π+ laboratory scattering angles between 50 degree and 130 degree were taken together with a complementary measurement at 60 degree for π-d elastic scattering. In general, we find agreement with models that include the πN P11 amplitude and disagreement with models that exclude or suppress it

  15. Measurements of the energy dependence of the analyzing power in pp elastic scattering in the CNI region

    International Nuclear Information System (INIS)

    We present new measurements of the analyzing power AN in proton-proton elastic scattering in the Coulomb-Nuclear Interference region at √s 7.7 and 21.7 GeV obtained with the polarized atomic hydrogen jet target at RHIC. These measurements complement our earlier results at √s = 6.8 and 13.7 GeV confirming the presence of a hadronic helicity flip amplitude contribution in proton-proton elastic scattering at lower energies (√s 13 GeV) are consistent with no hadronic helicity flip contribution.

  16. Calculation of vector analyzing power in the p+6,8He elastic scattering at intermediate energies

    Directory of Open Access Journals (Sweden)

    Ibraeva Elena

    2014-03-01

    Full Text Available A calculations of the analyzing power (Ay of the elastic proton scattering on 6He and 8He are presented in the framework of the Glauber multiple diffraction scattering at E = 71 and 1000 MeV/nucleon. The wave functions obtained in the three-body α-n-n-model for 6He and the density distribution function in the no-core shell model for 8He are used. Our calculations qualitatively reproduced the data of Ay for p6He and p8He scattering and compare with the calculations’ results in the other approaches.

  17. Cavity Ring-Down Spectroscopy Lite: A Low Power Analyzer for measuring Carbon Dioxide, Methane and Water Vapor

    Science.gov (United States)

    Fleck, Derek; Hoffnagle, John; Tan, Sze; He, Yonggang

    2016-04-01

    Greenhouse gas accumulation has contributed to the changes in environments across the globe. Monitoring these fluctuations on global and local scales will allow scientists to better understand contributions that are made from nature and humans. This has led to the deployment of analytical instrumentation of all types to the most remote areas as well as the most densely populated areas. This however requires instruments to be precise, versatile, robust, and most importantly have power requirements that are as not limited by location, i.e. low enough power consumption to run off of batteries or even solar array. Here we present a full greenhouse gas analyzer that utilizes a new method of CRDS to measure carbon dioxide, methane and water vapor that consumes only 25W and still maintains long term stability to allow for averaging time of over 3 hours. Measurements have a 1-σ precision of 30 ppb for CO2 and 300 ppt of CH4 with 5 minutes of averaging; and with measurements of 3 hour averages reaching precisions down to 40ppt of methane. Additionally this new flavor of CRDS has allowed for an overall increase in measurement dynamic range from traditional CW-CRDS measuring methane up to 1000ppm and carbon dioxide up to several percent. We will present supplemental data acquired using this <11 kg analyzer, including soil respirations using closed static chambers and 10m tower measurements from Santa Clara, CA.

  18. Presenting a model of repair and preventing maintenance of Bushehr nuclear power plants analyzing the data of similar nuclear power plants

    International Nuclear Information System (INIS)

    Due to the increase application of nuclear energy for producing electricity, special attention must be paid to their maintenance activities in general and preventive maintenance in particular. It has been shown that a well established preventive maintenance programme will enhance the reliability and availability of nuclear power plants. A model of preventive maintenance for Buhehr nuclear power plant which is due to be completed by 2001 is developed. The prescribed model is based on past experiences of VVER nuclear power plants around the world. The utilized data is provided by International Atomic Energy Agency (IAEA) in Vienna, Austria. The data and past experiences reveal such important information as availability, energy loss, types of failures, duration of failure, etc. A strategy for designing a database is established. These data are then analyzed by statistical methods such as Pareto analysis, t-test, K-S test, analysis of variance, etc. The results of our analysis reveal important information in regard to establishment of a well-defined preventive maintenance programme in Buhshehr nuclear power plant. The results show that certain equipment such turbo-generator and control-rods play an important role in the maintenance of a VVER nuclear power plant. Other findings are discussed in great detail

  19. Analyzing the possibility of constructing the air heating system for an integrated solid fuel gasification combined-cycle power plant

    Science.gov (United States)

    Mikula, V. A.; Ryzhkov, A. F.; Val'tsev, N. V.

    2015-11-01

    Combined-cycle power plants operating on solid fuel have presently been implemented only in demonstration projects. One of possible ways for improving such plants consists in making a shift to hybrid process circuits of integrated gasification combined-cycle plants with external firing of solid fuel. A high-temperature air heater serving to heat compressed air is a key element of the hybrid process circuit. The article describes application of a high-temperature recuperative metal air heater in the process circuit of an integrated gasification combined-cycle power plant (IGCC). The available experience with high-temperature air heating is considered, and possible air heater layout arrangements are analyzed along with domestically produced heat-resistant grades of steel suitable for manufacturing such air heater. An alternative (with respect to the traditional one) design is proposed, according to which solid fuel is fired in a noncooled furnace extension, followed by mixing the combustion products with recirculation gases, after which the mixture is fed to a convective air heater. The use of this design makes it possible to achieve considerably smaller capital outlays and operating costs. The data obtained from thermal and aerodynamic calculations of the high-temperature air heater with a thermal capacity of 258 MW for heating air to a temperature of up to 800°C for being used in the hybrid process circuit of a combined-cycle power plant are presented.

  20. Measurements of the energy dependence of the analyzing power in pp elastic scattering in the CNI region

    Energy Technology Data Exchange (ETDEWEB)

    Bazilevsky A.; Alekseev, I.; Aschenauer, E.; Atoyan, G.; Bravar, A.; Bunce, G.; Boyle, K.; Gill, R.; Huang, H.; Lee, S.; Makdisi, Y.; Morozov, B.; Nakagawa, I.; Okada, H.; Svirida, D.; Zelenski, A.

    2010-09-27

    We present new measurements of the analyzing power A{sub N} in proton-proton elastic scattering in the Coulomb-Nuclear Interference region at {radical}s = 7.7 and 21.7 GeV obtained with the polarized atomic hydrogen jet target at RHIC. These measurements complement our earlier results at {radical}s = 6.8 and 13.7 GeV confirming the presence of a hadronic helicity flip amplitude contribution in proton-proton elastic scattering at lower energies ({radical}s <8 GeV) while higher energy data ({radical}s >13 GeV) are consistent with no hadronic helicity flip contribution.

  1. COMMIX-PPC: A three-dimensional transient multicomponent computer program for analyzing performance of power plant condensers

    International Nuclear Information System (INIS)

    The COMMIX-PPC computer pregrain is an extended and improved version of earlier COMMIX codes and is specifically designed for evaluating the thermal performance of power plant condensers. The COMMIX codes are general-purpose computer programs for the analysis of fluid flow and heat transfer in complex Industrial systems. In COMMIX-PPC, two major features have been added to previously published COMMIX codes. One feature is the incorporation of one-dimensional equations of conservation of mass, momentum, and energy on the tube stile and the proper accounting for the thermal interaction between shell and tube side through the porous-medium approach. The other added feature is the extension of the three-dimensional conservation equations for shell-side flow to treat the flow of a multicomponent medium. COMMIX-PPC is designed to perform steady-state and transient. Three-dimensional analysis of fluid flow with heat transfer tn a power plant condenser. However, the code is designed in a generalized fashion so that, with some modification, it can be used to analyze processes in any heat exchanger or other single-phase engineering applications. Volume I (Equations and Numerics) of this report describes in detail the basic equations, formulation, solution procedures, and models for a phenomena. Volume II (User's Guide and Manual) contains the input instruction, flow charts, sample problems, and descriptions of available options and boundary conditions

  2. COMMIX-PPC: A three-dimensional transient multicomponent computer program for analyzing performance of power plant condensers

    Energy Technology Data Exchange (ETDEWEB)

    Chien, T.H.; Domanus, H.M.; Sha, W.T.

    1993-02-01

    The COMMIX-PPC computer program is an extended and improved version of earlier COMMIX codes and is specifically designed for evaluating the thermal performance of power plant condensers. The COMMIX codes are general-purpose computer programs for the analysis of fluid flow and heat transfer in complex industrial systems. In COMMIX-PPC, two major features have been added to previously published COMMIX codes. One feature is the incorporation of one-dimensional conservation of mass. momentum, and energy equations on the tube side, and the proper accounting for the thermal interaction between shell and tube side through the porous medium approach. The other added feature is the extension of the three-dimensional conservation equations for shell-side flow to treat the flow of a multicomponent medium. COMMIX-PPC is designed to perform steady-state and transient three-dimensional analysis of fluid flow with heat transfer in a power plant condenser. However, the code is designed in a generalized fashion so that, with some modification. it can be used to analyze processes in any heat exchanger or other single-phase engineering applications.

  3. Measurement of the vector analyzing power of the elastic pion-deuteron scattering in the range of presumed dibaryon resonances

    International Nuclear Information System (INIS)

    At the Swiss Institute for Nuclear Research angular distributions and analyzing power of the elastic pion-deuteron scattering was measured. Then pion energies amount 142, 219, 256, 275, 294, and 325 MeV. The alignment for deuteron spins resulted by the method of the dynamic nuclear polarization. The measurements were performed in two independent experiments. In the first experiment the scattered pions were detected by a magnetic spectrometer. The second experiment used the time-of-flight difference between elastically scattered pions and the corresponding recoil deuterons for the identification of an elastic πd scattering event. The angular distributions of the elastic vector analysing power exhibit a characteristic energy slope. From 256 MeV a minimum in the forward angular range is present which becomes with increasing energy ever more negative. Calculation in the three-body formalism cannot describe this slope from 256 MeV. A procedure which mixes to this theory a 1D2 and 1G4 dibargon resonance yields qualitatively good descriptions of the data. In order to establish resonance effects independently of models the available experimental data were subjected to a scattering phase analysis. The adjustment of small (orbital angular momenta L 1G4 resonance. (orig.)

  4. Measurement of analyzing powers of π+ and π- produced on a hydrogen and a carbon target with a 22-GeV/c incident polarized proton beam

    International Nuclear Information System (INIS)

    The analyzing powers of π+ and π- were measured using an incident 22-GeV/c transversely polarized proton beam at the Brookhaven Alternating Gradient Synchrotron. A magnetic spectrometer measured π± inclusive asymmetries on a hydrogen and a carbon target. An elastic polarimeter with a CH2 target measured pp elastic-scattering asymmetries to determine the beam polarization using published data for the pp elastic analyzing power. Using the beam polarization determined from the elastic polarimeter and asymmetries from the inclusive spectrometer, analyzing powers AN for π± were determined in the xF and pT ranges (0.45-0.8) and (0.3-1.2 GeV/c), respectively. The analyzing power results are similar in both sign and character to other measurements at 200 and 11.7 GeV/c, confirming the expectation that high-energy pion inclusive analyzing powers remain large and relatively energy independent. This suggests that pion inclusive polarimetry may be a suitable method for measuring future beam polarizations at BNL RHIC or DESY HERA. Analyzing powers of π+ and π- produced on hydrogen and carbon targets are the same. Various models to explain inclusive analyzing powers are also discussed

  5. Meeting summary of the second CSNI specialist meeting on simulators and plant analyzers - Current Issues in Nuclear Power Plant Simulation

    International Nuclear Information System (INIS)

    The Second CSNI Specialist Meeting on Simulators and Plant Analyzers: Current Issues in Nuclear Power Plant Simulation was held in Espoo, Finland, from September 29 through October 2, 1997. It was organised by CSNI Principal Working Group on Coolant System Behaviour (PWG2), Task Group on Thermal Hydraulic Applications (TG-THA), in co-operation with Technical Research Centre of Finland. The meeting in Espoo attracted some 90 participants from 17 countries. A total of 49 invited papers were presented in the meeting in addition to 7 simulator system demonstrations. Ample time was reserved for the presentations and informal discussions during the four meeting days. The previous meeting held in Lappeenranta, Finland, in 1992 collected some 85 participants from 12 countries, presenting a total of 40 papers. The meeting was structured into 6 sessions covering the important aspects of development and use of simulators and plant analyzers: Session I: New objectives, Requirements and Concepts. This session covered the progress experienced since the 1. simulator meeting and tried to address the changing role of simulators based on the changes in users' needs and developing possibilities. Session II: Trends in Simulation Technology. This session was reserved for studying the current trends in the simulation technology: software environments, visualisation, simulator configuration tools, programming languages and computer systems. Session III: Training and human factor studies using simulators. This session was created for studying the status of different uses of simulators such as educational simulators, human factor studies and integrated safety assessment in addition to traditional training. Regarding to the severe accidents, a question was raised whether the simulator use should be for training or education. Session IV: Modelling techniques. The session on modelling techniques was included to cover recent developments in the modelling techniques applicable to training

  6. Ergonomics as aid tool to identify and to analyze factors that can affect the operational performance of nuclear power plants

    International Nuclear Information System (INIS)

    The study of ergonomics has evolved around the world as one of the keys to understand human behavior in interaction with complex systems as nuclear power plant and to achieve the best match between the system and its users in the context of task to be performed. Increasing research efforts have yielded a considerable body of knowledge concerning the design of workstations, workplace, control rooms, human-system interfaces, user-interface interaction and organizational design to prevent worker discomfort, illness and also to improve productivity, product quality, ease of use and safety. The work ergonomics analysis consists of gathering a series of observation in order to better understand the work done and to propose changes and improvements in the working conditions. The work ergonomics analysis implies both the correction of existing situations (safety, reliability and production problems) and the development of new work system. Operator activity analysis provides a useful tool for the ergonomics approach, based on work ergonomics analysis. The operators will be systematically observed in their real work environment (control room) or in simulators. The focus is on description of the distributed regulated mechanisms (in the sense that operators work in crew), both in nominal and degraded situations, observing how operators regulate collectively their work during an increase in workload or when confronted with situations where incidents or accidents occur. Audio, video recorders and field notes can be used to collect empirical data, conversations and interactions that occur naturally within the work environment. Our research develops an applied ergonomics methodology, based on field studies, that permits to identify and analyze situations, factors that may affect the operational performance of nuclear power plants. Our contribution is related to the following technical topic: How best to learn from and share operational safety experience and manage changes during

  7. Measurement of the analyzing power for proton-carbon elastic scattering in the CNI region with a 22 GeV/c polarized proton beam

    International Nuclear Information System (INIS)

    We have carried out the experiment BNL-AGS E950 to measure the analyzing power for proton-carbon elastic scattering in the Coulomb-Nuclear Interference (CNI) region with a 22 GeV/c polarized proton beam. Recoil carbons from 300 keV to a few MeV in the CNI region, were detected inside the AGS ring to identify proton-carbon elastic scattering. The preliminary results of the analyzing power measurement are presented

  8. Measurement of the free neutron-proton analyzing power and spin transfer parameters in the charge exchange region at 790 MeV

    International Nuclear Information System (INIS)

    The free neutron-proton analyzing power and the spin transfer parameters (K/sub NN/, K/sub SS/, K/sub SL/, and K/sub LL/) were measured at the Los Alamos Meson Physics Facility at 790 MeV between 1650 and 1800 center of mass. A 40% polarized neutron beam incident on a liquid hydrogen target was used. The recoil protons were momentum analyzed with a magnetic spectrometer to isolate elastic scatters. A large solid angle carbon polarimeter was used to measure the proton polarization. The measurements are the first at this energy and are in basic agreement with pre-existing phase shift solutions. The proton-carbon analyzing power was measured between 500 and 750 MeV. An empirical fit to the proton-carbon analyzing power between 100 and 750 MeV was done

  9. Measurement of the free neutron-proton analyzing power and spin transfer parameters in the charge exchange region at 790 MeV

    Energy Technology Data Exchange (ETDEWEB)

    Ransome, R.D.

    1981-07-01

    The free neutron-proton analyzing power and the spin transfer parameters (K/sub NN/, K/sub SS/, K/sub SL/, and K/sub LL/) were measured at the Los Alamos Meson Physics Facility at 790 MeV between 165/sup 0/ and 180/sup 0/ center of mass. A 40% polarized neutron beam incident on a liquid hydrogen target was used. The recoil protons were momentum analyzed with a magnetic spectrometer to isolate elastic scatters. A large solid angle carbon polarimeter was used to measure the proton polarization. The measurements are the first at this energy and are in basic agreement with pre-existing phase shift solutions. The proton-carbon analyzing power was measured between 500 and 750 MeV. An empirical fit to the proton-carbon analyzing power between 100 and 750 MeV was done.

  10. Vector and tensor analyzing powers in the 208Pb(vector d,t)207Pb reaction at 200 and 360 MeV

    International Nuclear Information System (INIS)

    Cross-sections, vector and tensor analyzing powers for the main levels in 207Pb have been measured via the 208Pb (d,t) 207Pb reaction at 200 and 360 MeV incident energies. Ay and Ayy spin observables allow a clear identification of the valence levels, especially at 200 MeV. The results are compared with finite range DWBA calculations using the Paris projectile-ejectile form factor including the S and D components. The analysis shows a large effect of the D component on the tensor analyzing powers at the most forward angles. At both energies, the spin part of the deuteron optical potential is very important to describe the analyzing powers and especially Ayy. The good description of all observables at 200 MeV allows this reaction to be used as a spectroscopic tool

  11. Measurement of analyzing power for proton-carbon elastic scattering in the coulomb-nuclear interference region with a 22-GeV/c polarized proton beam.

    Science.gov (United States)

    Tojo, J; Alekseev, I; Bai, M; Bassalleck, B; Bunce, G; Deshpande, A; Doskow, J; Eilerts, S; Fields, D E; Goto, Y; Huang, H; Hughes, V; Imai, K; Ishihara, M; Kanavets, V; Kurita, K; Kwiatkowski, K; Lewis, B; Lozowski, W; Makdisi, Y; Meyer, H-O; Morozov, B V; Nakamura, M; Przewoski, B; Rinckel, T; Roser, T; Rusek, A; Saito, N; Smith, B; Svirida, D; Syphers, M; Taketani, A; Thomas, T L; Underwood, D; Wolfe, D; Yamamoto, K; Zhu, L

    2002-07-29

    The analyzing power for proton-carbon elastic scattering in the Coulomb-nuclear interference region of momentum transfer, 9.0x10(-3)<-t<4.1x10(-2) (GeV/c)(2), was measured with a 21.7 GeV/c polarized proton beam at the Alternating Gradient Synchrotron of Brookhaven National Laboratory. The ratio of hadronic spin-flip to nonflip amplitude, r(5), was obtained from the analyzing power to be Rer(5)=0.088+/-0.058 and Imr(5)=-0.161+/-0.226. PMID:12144435

  12. Measurement of analyzing power for proton-carbon elastic scattering in the Coulomb-nuclear interference region with a 22-GeV/c polarized proton beam

    International Nuclear Information System (INIS)

    The analyzing power for proton-carbon elastic scattering in the Coulomb-nuclear interference region of momentum transfer, 9.0x10-3-2 (GeV/c)2, was measured with a 21.7 GeV/c polarized proton beam at the Alternating Gradient Synchrotron of Brookhaven National Laboratory. The ratio of hadronic spin-flip to nonflip amplitude, r5, was obtained from the analyzing power to be Rer5=0.088±0.058 and Imr5=-0.161±0.226

  13. Analyzing power of inclusive production of π+,π-, and KS0 by polarized protons at 13.3 and 18.5 GeV/c

    International Nuclear Information System (INIS)

    We have measured the analyzing power in π+, π-, and KS0 production by a polarized proton beam at 13.3 and 18.5 GeV/c. The data cover the central and the beam fragmentation region, in the transverse-momentum range up to 2 GeV/c. The results indicate that sizable effects are present at high xF and also persist into the hard-scattering region for KS0 and π+. A zero value of the analyzing power was observed for π- production

  14. Measurement of the tensor-analyzing power A sub y sub y in deuteron breakup at 4.5 GeV/c and 80 mr

    CERN Document Server

    Ladygin, V P; Afanasiev, S V; Arkhipov, V V; Isupov, A Yu; Ivanov, V I; Kashirin, V A; Khrenov, A N; Kolesnikov, V I; Kuznetsov, V A; Ladygina, N B; Litvinenko, A G; Reznikov, S G; Rukoyatkin, P A; Semenov, A Yu; Semenova, I A; Stoletov, G D; Zhmyrov, V N; Zolin, L S; Bondarev, V K; Filipov, G; Kartamyshev, A A; Yudin, N P

    2002-01-01

    The tensor analyzing-power A sub y sub y in inclusive breakup of 4.5 GeV/c deuterons on berylium has been measured at /sim 80 mr of the detected proton angle. The analyzing power remains positive up to the highest measured momentum of the proton, that is in definitive contradiction with the predictions of the existing models based on the standard deuteron wave functions. The results suggest that the deuteron structure at short distances may depend on more than one independent variable. (author)

  15. Proposal on the measurements of d-p elastic scattering analyzing powers at 0.3-2.0 GeV at internal target station of the Nuclotron

    International Nuclear Information System (INIS)

    A new high-energy beam polarimeter is proposed for the Nuclotron using Internal Target Station. This polarimeter based on the measurement of the asymmetry for the d-p elastic scattering will allow one to measure both vector and tensor components of the deuteron beam polarization simultaneously. For that purpose the measurement of analyzing powers for the d-p elastic scattering at energies Td = 0.88-2 GeV is proposed. The precise measurements of the deuteron analyzing powers over energy range Td 300-2000 MeV can give an irreplaceable clue on the study of spin-dependence of three-nucleon forces

  16. Measurement of the tensor-analyzing power Ayy in deuteron breakup at 4.5 GeV/c and 80 mr

    International Nuclear Information System (INIS)

    The tensor analyzing-power Ayy in inclusive breakup of 4.5 GeV/c deuterons on berylium has been measured at /sim 80 mr of the detected proton angle. The analyzing power remains positive up to the highest measured momentum of the proton, that is in definitive contradiction with the predictions of the existing models based on the standard deuteron wave functions. The results suggest that the deuteron structure at short distances may depend on more than one independent variable. (author)

  17. A measurement to analyze the relative change in the Absolute Parity of Power Purchase: An application to the European Union

    OpenAIRE

    Feijoo, Santiago Rodriguez; Caro, Alejandro Rodriguez; Correa, Carlos Gonzalez

    2003-01-01

    In the present paper an index to measure the changes in the Absolute Purchasing Power Parity. in the short term of a group of territories that conform an unique market, using the information of the Harmonized Index of Consumer Prices and the Exchange Rates. This measurement is utilized to study the change in relative prices of the countries of the European Union for the period 1991-2002, and the fulfillment of the theory of the Relative Purchasing Power Parity, taking as a reference the Absol...

  18. Loss of a main feedwater pump test at 100% power simulation using Korean standard nuclear plant analyzer (KSNPA)

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Won Sang; Kim, Shin Whan; Sung, Kang Sik; Seo, Jong Tae; Lee, Sang Keun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1996-07-01

    The Loss of a Main Feedwater Pump test at 100% Power for YGN 4 was simulated in order to verify and validate the KSNPA. The comparison of the test data with the KSNPA prediction results showed reasonable agreement in the trends of the major plant parameters. All plant control systems including NSSS and T/G control systems are properly actuated and stabilized the plant conditions to a new steady state conditions in the KSNPA. From the comparison results, the KSNPA showed its capability to simulate the LOMFP event for the KOrean Standard Nuclear Power Plant.

  19. Analyzing power and cross section distributions of the 12C(p,pα)8Be cluster knockout reaction at an incident energy of 100 MeV

    International Nuclear Information System (INIS)

    The (p,pα) reaction on 12C was investigated experimentally using polarized incident protons of 100 MeV. The scattered proton and α particle, from the knockout reaction, were detected in coincidence. Coincident data, which were obtained at ten quasifree angle pairs for proton angles ranging from 25 deg. to 110 deg., were analyzed in terms of the distorted-wave impulse approximation (DWIA). Calculated energy-sharing cross section and analyzing power distributions reproduce the data reasonably well, indicating that a quasifree knockout mechanism dominates the reaction. Since measurements of analyzing powers were made, spin-orbit distortions were included in the DWIA calculations. The effects of this were found to be very small near zero recoil momentum and did not destroy the validity of the factorization approximation where the two-body p-α cross section enters as a multiplicative factor in the three-body (p,pα) cross section expression. Spectroscopic factors derived from the data are consistent with theoretical predictions. Analyzing power data also follow the trend of free p-4He scattering data, and comparisons with DWIA predictions are in reasonable agreement. Because the two-body interaction response between the projectile and the α cluster was found to resemble the scattering of protons from a free α particle to a remarkable degree, the present results would strongly imply the existence of preformed α clusters in 12C.

  20. Tensor Analyzing Power of the Relativistic Deuteron Fragmentation as a Means of Study of Deuteron Structure in the Framework of Light-Front Dynamics

    CERN Document Server

    Azhgirey, L S; Zhmyrov, N V; Zolin, L S; Ivanov, V I; Isupov, A Yu; Ladygin, V P; Litvinenko, A G; Peresedov, V F; Khrenov, A N; Yudin, N P

    2004-01-01

    New data on the tensor analyzing power $A_{yy}$ of the $^9$Be$(d,p)X$ reaction at an initial deuteron momentum of 5 GeV/$c$ and a proton detection angle of 178 mrad have been obtained at the JINR Synchrophasotron. The data obtained are analyzed within the framework of an approach based on the light-front dynamics using Karmanov's relativistic deuteron wave function. In contrast to the calculations with standard non-relativistic deuteron wave functions, we have managed to explain the new data within the framework of our approach without invoking degrees of freedom additional to nucleon ones.

  1. Differential cross section, analyzing power and phase shifts for p vector-3He elastic scattering below 1.0 MeV

    International Nuclear Information System (INIS)

    Differential cross sections and analyzing powers for the elastic scattering of polarized protons by unpolarized 3He nuclei have been measured at eight energies between 0.3 MeV and 1.0 MeV for scattering angles THETAsub(c.m.) = 52.40-173.30. The cross-section values were normalized to the Rutherford cross section for proton-krypton scattering. The analyzing powers have been measured with a statistical accuracy of about 0.001. The phase-shift analysis based on these data included all phases for orbital angular momenta / <= 1 and the channel-spin mixing parameter for the P waves. An energy parametrization of the phase shifts by an effective-range approximation allowed a simultaneous utilization of all data. (orig.)

  2. Cross sections and analyzing powers of 15N(p,n)15O at 200 MeV and 494 MeV

    International Nuclear Information System (INIS)

    Differential cross sections and analyzing powers have been measured for the 15N(p,n)15 O(g.s.) reaction at bombarding energies of 200 MeV and 494 MeV. The 494 MeV data were obtained at the LAMPF Neutron Time-Of-Flight Facility on an 82 m flight path with a resolution of about 2.7 MeV. The 200 MeV data were obtained at IUCF on a 76m flight path with a resolution of about 1.1 MeV. At both energies, the measured analyzing power is small, the magnitude is less than .2 for momentum transfers of less than 1 fm-1. In contrast, both Relativistic and standard DWIA calculations predict a maximum of A=-.7 near q=0.7 fm-1. 53 refs., 44 figs

  3. Incident-energy dependence of the analyzing power in the 58Ni(p,3He56Co reaction between 80 and 120 MeV

    Directory of Open Access Journals (Sweden)

    Steyn G.F.

    2012-12-01

    Full Text Available This project looks at the angular distributions of the differential cross sections and analyzing powers of a few low lying states of 56Co in the reaction 58Ni(p,3He56Co at three different incident energies between 80and 120 MeV. The measurements are compared with zero-range distorted-wave Born approximation (DWBA calculations in which we assume a simple direct two-nucleon pickup process. Earlier inclusive (p,3He reaction studies on similar targets were successfully treated in terms of a statistical pre-equilibrium multistep formalism, in which the final stage of the reaction involved a deuteron pickup, described by means of the DWBA. The analyzing power was shown to be rather sensitive to the contributions of the different order steps. However some features observed in the analyzing powers of these inclusive studies, though reproduced by the theory, are not fully understood.We therefore investigate the ability of the DWBA model to describe the (p,3He pickup reaction to discrete states at different incident energies using a high resolution spectrometer.

  4. The Role of X-Ray Diffraction for Analyzing Zr-Sn-Nb-Fe Alloys as Power Reactor Fuel Cladding

    International Nuclear Information System (INIS)

    Synthesis of Zr- 1%Nb- 1%Sn- 1%Fe alloy is undertaken in order to develop fuel cladding alloy at high burn-up. Powder specimens of Zr-Sn-Nb-Fe alloy were prepared and then formed into pellets with a dimension of 10 mm in height x 10 mm in diameter using a pressure of 1.2 ton/cm2. The 5 gram green pellets were then melted in an arc furnace crucible under argon atmosphere. The pressure in the furnace was set at 2 psi and the current was 50 A. Afterwards, the ingots were heated at a temperature of 1100 oC for 2 hours and subsequently quenched in water. The ingots then underwent annealing at temperatures of 400 oC, 500 oC, 600 oC, 700 oC, and 750 oC for 2 hours. The specimens were analyzed using X-ray diffraction in order to construct diffractograms. Results of the diffraction patterns were fitted with data from JCPDF (Joint Committee Powder Diffraction File) to determine the type of crystals in the elements or substances. The greater the crystallite dimension, the smaller the dislocation density. Agreeable results for hardening or strengthening were obtained at annealing temperatures of 500 oC and 700, whereas for softening or residual stress at 600 oC and 750 oC. The nucleation of the secondary phase precipitate (SPP) was favourable at annealing temperatures of 400 oC, 500 oC, and 700 oC. For Zr- 1%Nb- 1%Sn- 1%Fe alloy with annealing temperatures between 400 oC to 800 oC, precipitates of Fe2Nb, ZrSn2,FeSn, SnZr, NbSn2, Zr0.68Nb0.25Fe0.08, Fe2Nb0.4Zr0.6, Fe37Nb9Zr54, and ω-Zr were observed. Satisfactory precipitate stabilization was achieved at annealing temperature of 800 oC, growth of precipitates at temperature between 500 oC to 600 oC, and minimization of precipitate size at 700 oC. (author)

  5. The Role of X-Ray Diffraction for Analyzing Zr-Sn-Nb-Fe Alloys as Power Reactor Fuel Cladding

    Directory of Open Access Journals (Sweden)

    Sugondo

    2010-08-01

    Full Text Available Synthesis of Zr-1%Nb-1%Sn-1%Fe alloy is undertaken in order to develop fuel cladding alloy at high burn-up. Powder specimens of Zr-Sn-Nb-Fe alloy were prepared and then formed into pellets with a dimension of 10 mm in height 10 mm in diameter using a pressure of 1.2 ton/cm2. The 5 gram green pellets were then melted in an arc furnace crucible under argon atmosphere. The pressure in the furnace was set at 2 psi and the current was 50 A. Afterwards, the ingots were heated at a temperature of 1100°C for 2 hours and subsequently quenched in water. The ingots then underwent annealing at temperatures of 400°C, 500°C, 600°C, 700°C, and 750°C for 2 hours. The specimens were analyzed using X-ray diffraction in order to construct diffractograms. Results of the diffraction patterns were fitted with data from JCPDF (Joint Committee Powder Diffraction File to determine the type of crystals in the elements or substances. The greater the crystallite dimension, the smaller the dislocation density. Agreeable results for hardening or strengthening were obtained at annealing temperatures of 500°C and 700, whereas for softening or residual stress at 600°C and 750°C. The nucleation of the secondary phase precipitate (SPP was favourable at annealing temperatures of 400°C, 500°C, and 700°C. For Zr-1%Nb-1%Sn-1%Fe alloy with annealing temperatures between 400°C to 800°C, precipitates of Fe2Nb, ZrSn2,FeSn, SnZr, NbSn2, Zr0.68Nb0.25Fe0.08, Fe2Nb0.4Zr0.6, Fe37Nb9Zr54, and ω-Zr were observed. Satisfactory precipitate stabilization was achieved at annealing temperature of 800°C, growth of precipitates at temperature between 500°C to 600°C, and minimization of precipitate size at 700°C.

  6. 基于LabWindows/CVI的电能质量分析仪%Power Quality Analyzer Based on LabWindows/CVI

    Institute of Scientific and Technical Information of China (English)

    陈莉; 张宏立; 张瑞明

    2011-01-01

    To against the shortcomings of traditional power quality analyzing systems, I. E. , limited storage capacity and monotonous display functions, etc. , the hardware system combines high performance data acquisition module PCL-818H and industrial PC as the core is designed. The system can collect and analyze the real-time signals, in addition, by adopting the powerful test and analysis functions of virtual instrument LabWindows/ C VI, the calculations of phases and amplitudes of fundamental wave and harmonic waves; voltage deviation, distortion rate of active power and reactive power; and software of data storage function are completed. By repeating tests, it is shown that the analyzer features high accuracy, ease to read, reliable operation and high cost effective.%针对传统电能质量分析系统存在存储容量小、显示功能单调等缺点,设计了以高性能数据采集卡PCL-818H与工业控制计算机为核心的硬件系统.该系统对实时信号进行采集与分析,并利用虚拟仪器LabWindows/CVI的强大测试分析功能,完成了基波和谐波的幅值与相位、电压偏差、有功和无功畸变率等参数计算,且具有数据存盘的软件功能.通过反复验证,该分析仪具有精度较高、直观易读、工作可靠和性价比高等特点.

  7. Measurement of effective analyzing powers for the NTOF polarimeter at LAMPF and DLL(0 degree) for Gamow-Teller transitions in p-shell nuclei

    International Nuclear Information System (INIS)

    Measurements of neutron polarization from (rvec p,rvec n) reactions can provide valuable clues toward understanding the isovector nucleon-nucleus interaction. A neutron time-of-flight polarimeter has been constructed at the Los Alamos Meson Physics Facility to perform such measurements, but before the polarimeter can be used, its effective analyzing powers must be determined. This is accomplished by using the 14C(rvec p,rvec n)14N reaction at a bombarding energy of 494 MeV to produce a beam of neutrons with known polarization, illuminating the detector with these neutrons, and measuring the azimuthal asymmetries after scattering from a hydrogenous analyzer fluid within the detector. Secondary measurements are made using the 2H(rvec p,rvec n)2p reaction with bombarding energies of 318 and 494 MeV to produce a polarized neutron beam. The results from (rvec np) analyzing reactions within the detector agree with values anticipated from free nucleon-nucleon analyzing powers, but the results from (rvec np) analyzing reactions display a more than 33% reduction from the anticipated values. Additionally, measurements are made of the polarization transfer coefficient DLL(0 degree) for rvec p,rvec n Gamow-Teller reactions on 2H, 7Li12C, and 14C targets. For a purely central interaction, one would expect that DLL(0 degree) ∼ -1/3 in the plane wave limit, but a simple average of the Jπ = 0+ → 1+ results at a bombardment energy of 494 MeV gives DLL(0 degree) = -0.689 ± 0.044. Thus, the measurements indicate that the nucleon-nucleus interaction -- which is largely central at 200 MeV -- has strong tensor contributions at higher energy

  8. Neutron-scattering cross section and analyzing-power measurements for 208Pb from 6 to 10 MeV and optical model analyses

    International Nuclear Information System (INIS)

    Differential cross sections and analyzing powers have been obtained for the scattering of neutrons from the ground and first excited states of 208Pb. These new measurements include differential cross sections for elastic and inelastic neutron scattering at 8.0 MeV, and analyzing powers for elastic and inelastic neutron scattering at 6.0, 7.0, 8.0, 9.0, and 10.0 MeV. The present elastic scattering data have been combined with the previously measured TUNL data and data measured elsewhere in order to obtain a detailed and high accuracy data set for neutron elastic scattering from 208Pb over the 4.0 to 40.0 MeV energy range. This comprehensive data set has been described using the spherical optical model in which constant geometry fits, energy-dependent geometry fits, and fits incorporating the dispersion relation were performed. Although the overall description of the elastic n+208Pb scattering data was reasonably good using the various optical potentials, small systematic discrepancies remained at the backward angles of both the cross section and analyzing power data, and no optical model solution based on conventional Woods-Saxon form factors was found which could describe all of the details seen in the scattering data. To relax the constraint of having a Woods-Saxon form factor, the real central part of the optical model potential was modified using a Fourier-Bessel expansion of the real central potential. Individual fits at 6.0, 7.0, 8.0, 9.0, and 10.0 MeV, and fits to the combined 6.0 to 10.0 MeV data set were obtained using a Fourier-Bessel expansion of the real central potential and compared to fits using a conventional Woods-Saxon form factor

  9. Evidence for the noneikonal effects in the tensor and vector analyzing powers in p-d vector elastic scattering at 800 MeV

    International Nuclear Information System (INIS)

    Deuteron tensor and vector analyzing powers have been measured for the first time in p-d vector elastic scattering at 800 MeV proton laboratory energy for a-t range between 0.032 and 1.038 (GeV/c)2. The data provide a very sensitive test of the multiple scattering theory at intermediate energies. The inclusion of the noneikonal correction in the Glauber diffraction theory is essential in the description of the data, especially for-t approx. >= 0.2(GeV/c)2, where discrepancies of up to 150% are observed with the theory based on the eikonal approximation. (orig.)

  10. Measurement of the Analyzing Power $A_N$ in $pp$ Elastic Scattering in the CNI Region with a Polarized Atomic Hydrogen Gas Jet Target

    OpenAIRE

    Okada, H.; Alekseev, I. G.; Bravar, A; Bunce, G.; Dhawan, S.; Gill, R; Haeberli, W.; Jinnouchi, O.; Khodinov, A.; Makdisi, Y.; Nass, A.; Saito, N; Stephenson, E. J.; D.N. Svirida; Wise, T.

    2005-01-01

    A precise measurement of the analyzing power $A_N$ in proton-proton elastic scattering in the region of 4-momentum transfer squared $0.001 < |t| < 0.032 ({\\rm GeV}/c)^2$ has been performed using a polarized atomic hydrogen gas jet target and the 100 GeV/$c$ RHIC proton beam. The interference of the electromagnetic spin-flip amplitude with a hadronic spin-nonflip amplitude is predicted to generate a significant $A_N$ of 4--5%, peaking at $-t \\simeq 0.003 ({\\rm GeV}/c)^2$. This kinematic region...

  11. Analyzing powers for the 3He(rvec p,π+)4He reaction in the region of the Δ1232 resonance

    International Nuclear Information System (INIS)

    Angular distributions of the analyzing powers have been measured for the 3He(rvec p,π+)4He reaction at proton bombarding energies of 300, 416, and 507 MeV. These results, together with existing measurements at 178, 198, and 800 MeV, provide a comprehensive set of data spanning the region of the Δ1232 resonance. The results are compared with a phenomenological model that incorporates the amplitudes for the pp→dπ+ reaction and calculations from a microscopic (p,π+) model

  12. Measurement of the tensor analyzing power Ayy in the inelastic scattering of deuterons in the vicinity of excitation of baryonic resonances

    International Nuclear Information System (INIS)

    The tensor Ayy and vector Ay analyzing powers in the inelastic scattering of deuterons with a momentum of 4.5 GeV/c on beryllium at an angle of ∝80 mr in the vicinity of baryonic resonance excitation have been measured. The Ayy data being in good agreement with the previous results obtained at a zero angle demonstrate an approximate t scaling up to ∝-0.9 (GeV/c)2. The results of the experiment are compared with the predictions of the multiple-scattering and ω-meson exchange models. (orig.)

  13. Analyzing powers and interference between one- and multi-step processes in (polarized p, t) reactions on medium-mass vibrational nuclei

    International Nuclear Information System (INIS)

    A neutron-number (N) dependence of analyzing powers A (theta) has been observed for the first time in (polarized p, t) reactions leading to the quadrupole vibrational states (21+) in 98Ru, sup(102,108)Pd, 114Cd, 116Sn, and sup(120,126)Te. Although analyzing powers for the ground-state transitions A(theta,0 sub(g)sup(+)) are very similar to each other, those for the 21+ transitions A(theta,21+) for the nuclei belonging to the beginning of the N = 50 - 82 shell are markedly different, having almost opposite signs, from A(theta,21+) for nuclei belonging to the latter half of the major shell. The difference is explained as a result of a sign change of the interference between one- and inelastic multi-step processes in two-neutron pickup reactions. Nuclear structure effects on such an interference are discussed on the basis of the microscopic description of collective quadrupole oscillation of nuclei. (author)

  14. Analyzing powers for (p,t) transitions to the first-excited 2+ states of medium-mass nuclei and nuclear collective motions

    International Nuclear Information System (INIS)

    Vector analyzing powers A(theta) and differential cross sections σ(theta) have been measured, with the use of a polarized proton beam of 22.0 MeV and a magnetic spectrograph, for (p,t) reactions leading to the first-excited 2+ (21+) states of the following eighteen nuclei of N = 50 - 82: sup(92,94,96)Mo, sup(98,100,102)Ru, sup(102,104,106,108)Pd, sup(110,112,114)Cd, 116Sn, sup(120,126,128)Te, and 136Ba. In addition A(theta) and σ(theta) for sup(104,110)Pd(p,t) sup(102,108) Pd(0sub(g)+,21+) transitions have been measured at Esub(p) = 52.2 MeV. The experimental results are analyzed in terms of the first- and second-order DWBA including both inelastic two-step processes and sequential transfer (p,d)(d,t) two-step processes. Inter-ference effect between the direct and the two-step processes is found to play an essential role in the (p,t) reactions. A sum-rule method for calculating the (p,d)(d,t) spectroscopic amplitudes has been developed so as to take into account the ground-state correlation in odd-A nuclei. The nuclear-structure wave functions are constructed under the boson expansion method and the quasiparticle random phase approximation (qp RPA) method by using the monopole-pairing, quadrupole-pairing, and QQ forces. The characteristic features of the experimental A(theta) and σ(theta) are better explained in terms of the boson expansion method than in terms of the qp RPA. Dependence of the (p,t) analyzing powers on the static electric quadrupole moment of the 21+ state is found to be strong because of the reorientation (anharmonic) effect in the 21+ yiedls 21+ transfer process. (J.P.N.)

  15. Oxygen analyzer

    Science.gov (United States)

    Benner, William H.

    1986-01-01

    An oxygen analyzer which identifies and classifies microgram quantities of oxygen in ambient particulate matter and for quantitating organic oxygen in solvent extracts of ambient particulate matter. A sample is pyrolyzed in oxygen-free nitrogen gas (N.sub.2), and the resulting oxygen quantitatively converted to carbon monoxide (CO) by contact with hot granular carbon (C). Two analysis modes are made possible: (1) rapid determination of total pyrolyzable oxygen obtained by decomposing the sample at 1135.degree. C., or (2) temperature-programmed oxygen thermal analysis obtained by heating the sample from room temperature to 1135.degree. C. as a function of time. The analyzer basically comprises a pyrolysis tube containing a bed of granular carbon under N.sub.2, ovens used to heat the carbon and/or decompose the sample, and a non-dispersive infrared CO detector coupled to a mini-computer to quantitate oxygen in the decomposition products and control oven heating.

  16. Differential cross section and analyzing power of the ${\\vec p}p{\\to}pp{\\pi}^0$ reaction at a beam energy of 390 MeV

    CERN Document Server

    Maeda, Y; Ishida, T; Kacharava, A; Nomachi, M; Shimbara, Y; Sugaya, Y; Tamura, K; Yagita, T; Yasuda, K; Yoshida, H P; Wilkin, C

    2008-01-01

    The differential cross section and analyzing power $A_y$ of the ${\\vec p}p{\\to}pp{\\pi}^0$ reaction have been measured at RCNP in coplanar geometry at a beam energy of 390 MeV and the dependence on both the pion emission angle and the relative momentum of the final protons have been extracted. The angular variation of Ay for the large values of the relative momentum studied here shows that this is primarily an effect of the interference of pion s- and p-waves and this interference can also explain the momentum dependence. Within the framework of a very simple model, these results would suggest that the pion-production operator has a significant long-range component.

  17. Analyzing power in inclusive π+ and π- production at high xF with a 200 GeV polarized proton beam

    International Nuclear Information System (INIS)

    The analyzing power in inclusive charged pion production has been measured using the 200 GeV Fermilab polarized proton beam. A striking dependence in χF is observed in which AN increases from 0 to 0.42 with increasing χF for the π+ data and decreases from 0 to -0.38 with increasing χF for π- data. The kinematic range covered is 0.2≤χF≤0.9 and 0.2≤pT≤2.0 GeV/c. In a simple model our data indicate that at large χF the transverse spin of the proton is correlated with that of its quark constituents. (orig.)

  18. Investigation of the tensor analyzing power t{sub 20} in the reaction d{sup →} +p → {sup 3}He + η

    Energy Technology Data Exchange (ETDEWEB)

    Papenbrock, Michael; Fritzsch, Christopher; Goslawski, Paul; Khoukaz, Alfons; Mielke, Malte; Schroeer, Daniel; Taeschner, Alexander [Westfaelische Wilhelms-Universitaet, Muenster (Germany); Collaboration: ANKE-Collaboration

    2013-07-01

    Previous measurements on the reaction d{sup →} +p → {sup 3}He + η with the ANKE spectrometer at the COoler SYnchrotron - COSY - of the Forschungszentrum Juelich provided strong indications for the existence of a quasi-bound state of the η-{sup 3}He system. In order to gather more evidence for this possible quasi-bound state, measurements with a polarized deuteron beam have been performed at ANKE on the reaction d{sup →} +p → {sup 3}He + η. Hence, the investigation of the energy dependence of the tensor analyzing power t{sub 20} allows to study in more detail the role of the final state interaction in the strong enhancement of the total cross section. Recent results are presented and discussed. Furthermore, a brief outlook on the upcoming measurement on the reaction p+n → d+η in the context of η-mesic nuclei is given.

  19. Measurement of the tensor analyzing power in the inelastic scattering of deuteron on beryllium at an angle of 80 mrad at 4.5 GeV/c

    International Nuclear Information System (INIS)

    Tensor Ayy and vector Ayy analyzing powers of inelastic scattering of deuterons with momentum of 4.5 GeV/c on beryllium at and angle of ∼ 80 mrad in the vicinity of baryonic resonance excitation have been measured. The new Ayy data being plotted versus t are in good agreement with the previous data at 4/5, 5.5, and 9 GeV/c, obtained at zero angle in an overlapping region of t, and all existing data fit the common |t| dependence up to ∼ 0.9 (GeV/c)2. The results of the experiment are compared with the calculations in the framework of the multiple-scattering and ω-meson exchange models in t-channel

  20. COMMIX-PPC: A three-dimensional transient multicomponent computer program for analyzing performance of power plant condensers. Volume 2, User`s guide and manual

    Energy Technology Data Exchange (ETDEWEB)

    Chien, T.H.; Domanus, H.M.; Sha, W.T.

    1993-02-01

    The COMMIX-PPC computer program is an extended and improved version of earlier COMMIX codes and is specifically designed for evaluating the thermal performance of power plant condensers. The COMMIX codes are general-purpose computer programs for the analysis of fluid flow and heat transfer in complex industrial systems. In COMMIX-PPC, two major features have been added to previously published COMMIX codes. One feature is the incorporation of one-dimensional conservation of mass. momentum, and energy equations on the tube side, and the proper accounting for the thermal interaction between shell and tube side through the porous medium approach. The other added feature is the extension of the three-dimensional conservation equations for shell-side flow to treat the flow of a multicomponent medium. COMMIX-PPC is designed to perform steady-state and transient three-dimensional analysis of fluid flow with heat transfer in a power plant condenser. However, the code is designed in a generalized fashion so that, with some modification. it can be used to analyze processes in any heat exchanger or other single-phase engineering applications.

  1. A data mining approach: Analyzing wind speed and insolation period data in Turkey for installations of wind and solar power plants

    International Nuclear Information System (INIS)

    Highlights: ► Wind speed and insolation period data were analyzed using a data mining approach. ► Most of the studies in the literature were based on Weibull and Rayleigh models. ► Nearest and farest neighbor algorithms were used with different distance metrics. ► Many inferences were achieved in efficient limits for wind and solar farm analyses. - Abstract: Wind and solar power plant installations have been recently increased rapidly with respect to the depletion of fossil-based fuels all over the world. Due to stochastic nature of meteorological conditions, wind and solar energies have a non-schedulable nature and they require several installation analyses to determine the location and the capacities of wind and solar power to be produced. This paper focuses on the similarity, feasibility and numerical analyses of 75 cities in Turkey based on the monthly average wind speed and insolation period data. The nearest and the farest neighbor algorithms are used as agglomerative hierarchical clustering methods with Euclidean, Manhattan and Minkowski distance metrics in the stage of making the similarity and feasibility analyses. The maximum cophenetic correlation coefficient is achieved by the nearest neighbor algorithm with the Minkowski distance metric in the similarity and feasibility analyses. On the other hand, graphical representations of the monthly average wind speed and insolation period data are utilized for making the numerical analysis. The highest annual average wind speed and insolation period are obtained as 3.88 m/s and 8.45 h/day, respectively. Overall, many inferences were achieved in acceptable and efficient limits for wind and solar energy.

  2. Determination of the analyzing power of the A4 Compton-backscattering polarimeter for the measurement of the longitudinal spin polarization of the MAMI electron beam

    International Nuclear Information System (INIS)

    The A4 experiment determines the strange quark contribution to the electromagnetic from factors of the nucleon by measuring the parity violation in elastic electron nucleon scattering. These measurements are carried out using the spin polarized electron beam of the Mainzer Mikrotron (MAMI) with beam energies in the range from 315 to 1508 MeV. For the data analysis it is essential to determine the degree of polarization of the electron beam in order to extract the physics asymmetry from the measured parity violating asymmetry. For this reason the A4 collaboration has developed a novel type of Compton laser backscattering polarimeter that allows for a non-destructive measurement of the beam polarization in parallel to the running parity experiment. In the scope of this work the polarimeter was refined in order to enable reliable continuous operation of the polarimeter. The data acquisition system for the photon and electron detector was re-designed and optimized to cope with high count rates. A novel detector (LYSO) for the backscattered photons was commissioned. Furthermore, GEANT4 simulations of the detectors have been performed and an analysis environment for the extraction of Compton asymmetries from the backscattered photon data has been developed. The analysis makes use of the possibility to detect backscattered photons in coincidence with the scattered electrons, thus tagging the photons. The tagging introduces a differential energy scale which enables the precise determination of the analyzing power. In this work the analyzing power of the polarimeter has been determined. Therefore, at a beam current of 20 μA the product of electron and laser polarization can be determined, while the parity experiment is running, with a statistical accuracy of 1 % in 24 hours at 855 MeV or 2=0.6 (GeV/c)2 the analysis yields a raw asymmetry of ARohPV=(-20.0±0.9stat) x 10-6 at the moment. For a beam polarization of 80 % the total error would be 1,68 x 10-6 with ΔPe/Pe=5

  3. Measurement of the analyzing power A{sub N} in pp elastic scattering in the CNI region with a polarized atomic hydrogen gas jet target

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H. [Kyoto University, Sakyo-ku, Kyoto 606-8502 (Japan); RIKEN, Wako, Saitama 351-0198, (Japan); Alekseev, I.G. [Institute for Theoretical and Experimental Physics, 117259 Moscow (Russian Federation); Bravar, A. [Brookhaven National Laboratory, Upton, NY 11973 (United States)]. E-mail: bravar@bnl.gov; Bunce, G. [Brookhaven National Laboratory, Upton, NY 11973 (United States); RIKEN BNL Research Center, Upton, NY 11973 (United States); Dhawan, S. [Yale University, New Haven, CT 06520 (United States); Gill, R. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Haeberli, W. [Stony Brook University, Stony Brook, NY 11794 (United States); Jinnouchi, O. [RIKEN BNL Research Center, Upton, NY 11973 (United States); Khodinov, A. [Stony Brook University, Stony Brook, NY 11794 (United States); Makdisi, Y. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Nass, A. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Saito, N. [Kyoto University, Sakyo-ku, Kyoto 606-8502 (Japan); RIKEN, Wako, Saitama 351-0198 (Japan); Stephenson, E.J. [Indiana University Cyclotron Facility, Bloomington, IN 47408 (United States); Svirida, D.N. [Institute for Theoretical and Experimental Physics, 117259 Moscow (Russian Federation); Wise, T. [University of Wisconsin, Madison, WI 53706 (United States); Zelenski, A. [Brookhaven National Laboratory, Upton, NY 11973 (United States)

    2006-07-20

    Precise measurement of the analyzing power A{sub N} in proton-proton elastic scattering in the region of 4-momentum transfer squared 0.001< vertical bar t vertical bar <0.032 (GeV/c){sup 2} has been performed using a polarized atomic hydrogen gas jet target and the 100 GeV/c RHIC proton beam. The interference of the electromagnetic spin-flip amplitude with a hadronic spin-nonflip amplitude is predicted to generate a significant A{sub N} of 4-5%, peaking at -t{approx}0.003 (GeV/c){sup 2}. This kinematic region is known as the Coulomb nuclear interference region. A possible hadronic spin-flip amplitude modifies this calculable prediction. We present the first precise result of the CNI asymmetry and shape as a function of t. Our data are well described by the CNI prediction with the electromagnetic spin-flip alone and do not support the presence of a large hadronic spin-flip amplitude.

  4. Measurement of total and differential cross sections and analyzing power for pions in inelastic proton-proton anti pp→ppπdeg scattering

    International Nuclear Information System (INIS)

    A new solid angle detector, SPESO-2π, has been constructed in order to obtain clear data for this reaction. It consists mainly of 24 lead glass bars, arranged vertically in two shells around the liquid hydrogen target. A circle of scintillators vetoes charged particles. The bars serve as Cerenkov counters. A new fast topological trigger was developed which rapidly separates good configurations of two photon hits from background. A simulation code was set up that offered the opportunity to create pion events according to several theoretical models. The combination of measured values and simulation calculation provided the final results. The total cross sections follow exactly the established excitation function, but with much smaller error bars. No indication for a narrow dibaryon resonance with M=2121 MeV has been found. The differential cross sections were established over half of the angular range and the analyzing power has been measured for the first time in such a systematic way. The comparison with neutron-proton scattering with charged pion production reveals the existence of a non negligible partial cross section below 600 MeV

  5. Complete angular distribution measurements of pp spin correlation parameters Axx, Ayy, and Axz and analyzing power Ay at 197.4 MeV

    International Nuclear Information System (INIS)

    Measurements of pp spin correlation coefficients Axx, Ayy, and Axz and analyzing power Ay for pp elastic scattering at 197.4 MeV over the laboratory angular range 3.5 degree - 43.5 degree (θc.m.=7 degree - 90 degree) have been carried out. The typical statistical accuracy per 1 degree angle bin is better than 0.02 for the Amn and better than 0.005 for Ay. Systematic errors are negligible except for an overall normalization uncertainty of 2.5% for Amn and 1.3% for Ay. The experiment makes use of a polarized hydrogen gas target internal to a proton storage ring (IUCF Cooler) and a circulating beam of polarized protons. The target polarization is switched in sign and direction (x,y,z) every 2 s by reversing a weak guide field (∼0.3 mT). Scattered and recoil protons are detected in coincidence by two sets of wire chambers, by scintillators, and by silicon-strip recoil detectors placed 5 cm from the proton beam. Analysis methods and comparison to recent pp partial-wave analyses and NN potential models are described. copyright 1998 The American Physical Society

  6. Measurement of the Ayy tensor analyzing power for the 1H(rvec d,pp)n reaction in the symmetric constant relative energy geometry

    International Nuclear Information System (INIS)

    Measurements of the unpolarized triple differential cross section and the Ayy tensor analyzing power for the 1H(d,pp)n reaction were made using a 94.5 MeV polarized deuteron beam at the Indiana University Cyclotron Facility. Scattering angles (θ and φ) and energy information were recorded for the two emerging protons using large-area wire chambers backed by stopping plastic scintillator detectors. Events were selected that were close to the symmetric constant relative energy geometry in order to enhance the sensitivity of the observables to off-shell and three-body effects. The measurements covered values of α, the center-of-mass angle between the incoming proton and the outgoing neutron, from 72 degree to 180 degree. Comparisons are made to Faddeev calculations that use either separable potentials or an exact treatment of the S-wave nucleon-nucleon interaction in conjunction with a perturbative treatment of higher partial waves. While none of these calculations, which use only two-nucleon interactions, is completely satisfactory, there remains too much variation among different theoretical treatments to demonstrate the need for including additional dynamical features in the three-body model

  7. Educational laboratory based on a multifunctional analyzer of a reactor of a nuclear power plant with a water-moderated water-cooled reactor

    International Nuclear Information System (INIS)

    Authors presents an educational laboratory Safety and Control of a Nuclear Power Facility established by the Department of Automation for students and specialists of the nuclear power industry in the field of control, protection, and safe exploitation of reactor facilities at operating, constructing, and designing nuclear power plants with water-moderated water-cooled reactors

  8. Tensorial analyzing power T20 at 1800C.M. in d vector p elastic scattering between 0.3 and 2.3 GeV

    International Nuclear Information System (INIS)

    The results of the measurement of the analysing power T20 at 1800 CM in d vector p elastic scattering for 16 energies between 300 and 2300 MeV are presented. The values which have been obtained are badly reproduced by the calculations based on neutron transfer (ONT) and Δ excitation in the intermediate state (TME) mechanisms, principal beyond 1 GeV. The excitation of possible tribaryon resonances, which are introduced in an elementary way, is added to these two mechanisms. The results of these calculations show that one could thus obtain a satisfying agreement with the experimental values. A measurement of angular distribution of the analysing powers Asub(y) and Asub(yy) between 70 and 1800 CM at 1200 MeV is also presented

  9. Power

    OpenAIRE

    Bowles, Samuel; Gintis, Herbert

    2007-01-01

    We consider the exercise of power in competitive markets for goods, labour and credit. We offer a definition of power and show that if contracts are incomplete it may be exercised either in Pareto-improving ways or to the disadvantage of those without power. Contrasting conceptions of power including bargaining power, market power, and consumer sovereignty are considered. Because the exercise of power may alter prices and other aspects of exchanges, abstracting from power may miss essential a...

  10. Analyzing indirect effects in cluster randomized trials. The effect of estimation method, number of groups and group sizes on accuracy and power.

    Directory of Open Access Journals (Sweden)

    Joop eHox

    2014-02-01

    Full Text Available Cluster randomized trials assess the effect of an intervention that is carried out at the group or cluster level. Ajzen’s theory of planned behaviour is often used to model the effect of the intervention as an indirect effect mediated in turn by attitude, norms and behavioural intention. Structural equation modelling (SEM is the technique of choice to estimate indirect effects and their significance. However, this is a large sample technique, and its application in a cluster randomized trial assumes a relatively large number of clusters. In practice, the number of clusters in these studies tends to be relatively small, e.g. much less than fifty. This study uses simulation methods to find the lowest number of clusters needed when multilevel SEM is used to estimate the indirect effect. Maximum likelihood estimation is compared to Bayesian analysis, with the central quality criteria being accuracy of the point estimate and the confidence interval. We also investigate the power of the test for the indirect effect. We conclude that Bayes estimation works well with much smaller cluster level sample sizes such as 20 cases than maximum likelihood estimation; although the bias is larger the coverage is much better. When only 5 to 10 clusters are available per treatment condition even with Bayesian estimation problems occur.

  11. Analyzing powers and proton spin transfer coefficients in the elastic scattering of 800 MeV polarized protons from an L-type polarized deuteron target at small momentum transfers

    International Nuclear Information System (INIS)

    Analyzing powers and spin transfer coefficients which describe the elastic scattering of polarized protons from a polarized deuteron target have been measured. The energy of the proton beam was 800 MeV and data were taken at laboratory scattering angles of 7, 11, 14, and 16.5 degrees. One analyzing power was also measured at 180 degrees. Three linearly independent orientations of the beam polarization were used and the target was polarized parallel and antiparallel to the direction of the beam momentum. The data were taken with the high resolution spectrometer at the Los Alamos Meson Physics Facility (experiment 685). The results are compared with multiple scattering predictions based on Dirac representations of the nucleon-nucleon scattering matrices. 27 refs., 28 figs., 4 tabs

  12. Measurement of the tensor (Ayy) and vector (Ay) analyzing powers in the fragmentation of a 9-GeV/c deuteron on hydrogen and carbon nuclei at high proton transverse momenta

    International Nuclear Information System (INIS)

    Data on the tensor and vector analyzing powers (Ayy and Ay, respectively) in the fragmentation of a 9-GeV/c deuteron on hydrogen and carbon nuclei at high proton transverse momenta are presented. These data are compared with the results of relevant calculations performed within light-front dynamics by using various deuteron wave functions. The best description of the data is attained with the relativistic deuteron wave function derived within field-theory light-front dynamics

  13. Differential cross section, tensor Ayy and vector Ay analyzing power in the 12C(d, p)X reaction at 9 GeV/c and 85 mrad emission angle of protons

    International Nuclear Information System (INIS)

    The experimental data on the differential cross section, tensor Ayy and vector Ay analyzing powers in the deuteron breakup reaction on carbon 12C(d, p)X obtained at initial momenta 9 GeV/c and 85 mr emission angle of protons are presented. While the differential cross section is satisfactorily described within the framework of the hard scattering model using conventional deuteron wave functions, the behaviour of the tensor analyzing power Ayy, which remains positive up to the highest measured momenta of protons, is in disagreement with the predictions of this model. The non-zero values of the vector analyzing power Ay can indicate that the spin-dependent part of the nucleon-nucleon amplitude can be significant in the mechanism of this reaction. Simultaneously, the data on the differential cross section, Ayy and Ay in the 12C(d, p)X reaction in the vicinity of missing masses ∼ 2.2 GeV/c are obtained

  14. Analyzing Cosmic Bubble Collisions

    CERN Document Server

    Gobbetti, Roberto

    2012-01-01

    We develop a set of controlled, analytic approximations to study the effects of bubble collisions on cosmology. We expand the initial perturbation to the inflaton field caused by the collision in a general power series, and determine its time evolution during inflation in terms of the coefficients in the expansion. In models where the observer's bubble undergoes sufficient slow-roll inflation to solve the flatness problem, in the thin wall limit only one coefficient in the expansion is relevant to observational cosmology, allowing nearly model-independent predictions. We discuss two approaches to determining the initial perturbation to the inflaton and the implications for the sign of the effect (a hot or cold spot on the Cosmic Microwave Background temperature map). Lastly, we analyze the effects of collisions with thick-wall bubbles, i.e. away from the thin-wall limit.

  15. Power

    DEFF Research Database (Denmark)

    Elmholdt, Claus Westergård; Fogsgaard, Morten

    2016-01-01

    In this chapter, we will explore the dynamics of power in processes of creativity, and show its paradoxical nature as both a bridge and a barrier to creativity in organisations. Recent social psychological experimental research (Slighte, de Dreu & Nijstad, 2011) on the relation between power and...... creativity suggests that when managers give people the opportunity to gain power and explicate that there is reason to be more creative, people will show a boost in creative behaviour. Moreover, this process works best in unstable power hierarchies, which implies that power is treated as a negotiable and...... floating source for empowering people in the organisation. We will explore and discuss here the potentials, challenges and pitfalls of power in relation to creativity in the life of organisations today. The aim is to demonstrate that power struggles may be utilised as constructive sources of creativity. It...

  16. Analyzing powers for 2H(d(vector sign),d)2H at deuteron energies of 3.0, 4.75, and 6.0 MeV

    International Nuclear Information System (INIS)

    Tensor analyzing powers for 2H(d(vector sign),d)2H elastic scattering were measured at deuteron energies of 3.0, 4.75, and 6.0 MeV. The measured values are below 0.02 and increase with increasing energy. The data were compared to the results of an R-matrix parametrization and microscopic four-body calculations. The calculations indicate that the nucleon-nucleon p waves have a strong effect on the observables. (c) 2000 The American Physical Society

  17. Measurement of the Tensor $A_{yy}$ and Vector $A_y$ Analyzing Powers of the Deuteron Inelastic Scattering on Beryllium at 5.0 GeV/c and 178 mrad

    CERN Document Server

    Azhgirey, L S; Isupov, A Yu; Ivanov, V I; Khrenov, A N; Ladygin, V P; Ladygina, N B; Litvinenko, A G; Peresedov, V F; Yudin, N P; Zhmyrov, V N; Zolin, L S

    2004-01-01

    Tensor $A_{yy}$ and vector $A_{y}$ analyzing powers in the inelastic scattering of deuterons with a momentum of 5.0 GeV/c on beryllium at an angle of 178 mrad in the vicinity of the excitation of baryonic resonances with masses up to $\\sim$ 1.8 GeV/${\\rm c}^2$ have been measured. The $A_{yy}$ data are in good agreement with the previous data obtained at 4.5 and 5.5 GeV/c. The results of the experiment are compared with the predictions of the plane-wave impulse approximation and $\\omega$-meson exchange model.

  18. PDA: Pooled DNA analyzer

    Directory of Open Access Journals (Sweden)

    Lin Chin-Yu

    2006-04-01

    Full Text Available Abstract Background Association mapping using abundant single nucleotide polymorphisms is a powerful tool for identifying disease susceptibility genes for complex traits and exploring possible genetic diversity. Genotyping large numbers of SNPs individually is performed routinely but is cost prohibitive for large-scale genetic studies. DNA pooling is a reliable and cost-saving alternative genotyping method. However, no software has been developed for complete pooled-DNA analyses, including data standardization, allele frequency estimation, and single/multipoint DNA pooling association tests. This motivated the development of the software, 'PDA' (Pooled DNA Analyzer, to analyze pooled DNA data. Results We develop the software, PDA, for the analysis of pooled-DNA data. PDA is originally implemented with the MATLAB® language, but it can also be executed on a Windows system without installing the MATLAB®. PDA provides estimates of the coefficient of preferential amplification and allele frequency. PDA considers an extended single-point association test, which can compare allele frequencies between two DNA pools constructed under different experimental conditions. Moreover, PDA also provides novel chromosome-wide multipoint association tests based on p-value combinations and a sliding-window concept. This new multipoint testing procedure overcomes a computational bottleneck of conventional haplotype-oriented multipoint methods in DNA pooling analyses and can handle data sets having a large pool size and/or large numbers of polymorphic markers. All of the PDA functions are illustrated in the four bona fide examples. Conclusion PDA is simple to operate and does not require that users have a strong statistical background. The software is available at http://www.ibms.sinica.edu.tw/%7Ecsjfann/first%20flow/pda.htm.

  19. Concordance study and population frequencies for 16 autosomal STRs analyzed with PowerPlex(®) ESI 17 and AmpFℓSTR(®) NGM SElect™ in Somalis, Danes and Greenlanders

    DEFF Research Database (Denmark)

    Tomas Mas, Carmen; Mogensen, H S; Friis, S L; Hallenberg, C; Stene, M C; Morling, N

    2014-01-01

    433 system in an individual from Denmark and six in the SE33 system in six individuals from Somalia. Sequencing of SE33 in the six samples with discordant results showed G>A transition 15bp downstream of the repeat unit in three of the individuals, and G>A transition 68bp downstream of the repeat unit...... in the other three individuals. Population data for 16 autosomal STR systems analyzed in 989 individuals from Somalia, Denmark and Greenland are also presented. The highest mean heterozygosity was observed in Danes (82.5%). With the exception of D8S1179 in Danes, no significant deviations from Hardy...... ones included in the analyses. The highest combined chance of exclusion and power of discrimination was observed for Danes reaching values of 99.9999987% and 1 in 1.8×10(21), respectively....

  20. On line chemical analyzers for high purity steam and water, applied to steam power plants; Analizadores quimicos en linea para agua y vapor de alta pureza, aplicados a centrales termoelectricas

    Energy Technology Data Exchange (ETDEWEB)

    Diaz Perez, Ruth [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1989-12-31

    This article presents a general overview of the advances in the subject of on line analyzers of chemical parameters for high purity water and steam and specifies which ones are commercially available. Also are mentioned besides, the criteria nowadays applied for the selection of the sites for sample grabbing and the analysis that is necessary to perform in each point, depending on the power plant type and the treatment administered (phosphates-Ph coordinated or AVT treatment). [Espanol] El articulo presenta un panorama general de los avances que en materia de analizadores de parametros quimicos en linea para agua y vapor de alta pureza, y especifica cuales estan disponibles en forma comercial. Se citan, ademas los criterios que se aplican actualmente para seleccionar los puntos de toma de muestra y los analisis que es necesario efectuar en cada punto, dependiendo del tipo de central y del tratamiento que se le administre (fosfatos-pH coordinado o tratamiento AVT).

  1. NEPTUN-A spectrometer for measuring the Spin Analyzing Power in p-p elastic scattering at large P2⊥ at 400 GeV (and 3 TeV) at UNK

    Science.gov (United States)

    Lin, Ali M. T.

    1995-09-01

    We are constructing the NEPTUN-A spectrometer for measuring the Spin Analyzing Power in p+p↑→p+p at P2⊥=2 to 10 (GeV/c)2 at 400 GeV (or at 3 TeV) when the UNK accelerator in Protvino, Russia, becomes operational. The spectrometer consists of a 55 m long recoil arm with 3 horizontally bending magnets to guide the recoil protons onto a fixed 37° line. Then two vertical dipole magnets bend the protons up by 12° for momentum analysis. The momentum will be measured to an accuracy of 0.1% using chambers. In order to accept a large solid angle, the spectrometer contains a strong-focusing pair of quadrupoles looking at the polarized proton jet target. The forward arm consists of scintillator hodoscopes for measurement of the forward vertical angle. Acceptances and event rates are calculated. The status of the spectrometer is reported.

  2. Soft Decision Analyzer

    Science.gov (United States)

    Steele, Glen; Lansdowne, Chatwin; Zucha, Joan; Schlensinger, Adam

    2013-01-01

    The Soft Decision Analyzer (SDA) is an instrument that combines hardware, firmware, and software to perform realtime closed-loop end-to-end statistical analysis of single- or dual- channel serial digital RF communications systems operating in very low signal-to-noise conditions. As an innovation, the unique SDA capabilities allow it to perform analysis of situations where the receiving communication system slips bits due to low signal-to-noise conditions or experiences constellation rotations resulting in channel polarity in versions or channel assignment swaps. SDA s closed-loop detection allows it to instrument a live system and correlate observations with frame, codeword, and packet losses, as well as Quality of Service (QoS) and Quality of Experience (QoE) events. The SDA s abilities are not confined to performing analysis in low signal-to-noise conditions. Its analysis provides in-depth insight of a communication system s receiver performance in a variety of operating conditions. The SDA incorporates two techniques for identifying slips. The first is an examination of content of the received data stream s relation to the transmitted data content and the second is a direct examination of the receiver s recovered clock signals relative to a reference. Both techniques provide benefits in different ways and allow the communication engineer evaluating test results increased confidence and understanding of receiver performance. Direct examination of data contents is performed by two different data techniques, power correlation or a modified Massey correlation, and can be applied to soft decision data widths 1 to 12 bits wide over a correlation depth ranging from 16 to 512 samples. The SDA detects receiver bit slips within a 4 bits window and can handle systems with up to four quadrants (QPSK, SQPSK, and BPSK systems). The SDA continuously monitors correlation results to characterize slips and quadrant change and is capable of performing analysis even when the

  3. Analyzing in the Present

    DEFF Research Database (Denmark)

    Revsbæk, Line; Pedersen, Lene Tanggaard

    2015-01-01

    The article presents a notion of “analyzing in the present” as a source of inspiration in analyzing qualitative research materials. The term emerged from extensive listening to interview recordings during everyday commuting to university campus. Paying attention to the way different parts of...... various interviews conveyed diverse significance to the listening researcher at different times became a method of continuously opening up the empirical material in a reflexive, breakdown-oriented process of analysis. We argue that situating analysis in the present of analyzing emphasizes and acknowledges...... contributes to an ongoing methodological conversation problematizing the notion of “data” and the use of “data-reliant” methods of analysis....

  4. Analyzing current situation and management solution of the information security of the power enterprise%电力企业信息安全现状分析及管理对策

    Institute of Scientific and Technical Information of China (English)

    郭建; 顾志强

    2013-01-01

    随着信息化不断发展,信息安全所面临的危险已渗透到电力企业生产、经营的各个方面,信息安全问题变得越来越重要.文中通过对电力企业信息安全管理现状进行分析,指出目前电力企业在信息安全体系和信息安全管理层面存在诸多风险,提出建设一套合理有效的企业信息安全管理策略,解决电力企业信息安全管理问题,提升电力企业信息安全管理水平.最后重点强调企业信息安全管理工作是一个系统性、整体性的管理工作,电力企业需要统筹兼顾,统一规划并建立一套完善的信息安全保障体系.%With the development of information technology, the danger of the information security has also affect to every aspect such as producing and management in the power enterprise, as the result, the information security has become more and more important. This article analyzed the current situation of the information security management of the power enterprise. It pointed out that many risks of the information security system and information security management level. The reasonable and effective strategy of the information security is necessary. Thus solving the management of the information security, and raising the level of the information security. In the end, it stressed that the information security management is a systemic and integrity management work. To construct a perfect information security safeguard system, the power enterprise should make a perfect plan based on every aspect.

  5. Miniature mass analyzer

    CERN Document Server

    Cuna, C; Lupsa, N; Cuna, S; Tuzson, B

    2003-01-01

    The paper presents the concept of different mass analyzers that were specifically designed as small dimension instruments able to detect with great sensitivity and accuracy the main environmental pollutants. The mass spectrometers are very suited instrument for chemical and isotopic analysis, needed in environmental surveillance. Usually, this is done by sampling the soil, air or water followed by laboratory analysis. To avoid drawbacks caused by sample alteration during the sampling process and transport, the 'in situ' analysis is preferred. Theoretically, any type of mass analyzer can be miniaturized, but some are more appropriate than others. Quadrupole mass filter and trap, magnetic sector, time-of-flight and ion cyclotron mass analyzers can be successfully shrunk, for each of them some performances being sacrificed but we must know which parameters are necessary to be kept unchanged. To satisfy the miniaturization criteria of the analyzer, it is necessary to use asymmetrical geometries, with ion beam obl...

  6. Software Design Analyzer System

    Science.gov (United States)

    Tausworthe, R. C.

    1985-01-01

    CRISP80 software design analyzer system a set of programs that supports top-down, hierarchic, modular structured design, and programing methodologies. CRISP80 allows for expression of design as picture of program.

  7. The analyzing power Asub(y)(THETA) for 12C(n vector,nsub(0,1))12C in the neutron energy range from 6.8 to 17.3 MeV

    International Nuclear Information System (INIS)

    The analyzing power for the elastic and inelastic neutron scattering to the first excited state on 12C was measured at 21 energies from 6.8 to 17.3 MeV. The data from 8.9 to 14.9 MeV were together with very precise cross section data from the literature studied in the framework of the spherical optical model and the coupled channel formalism. The coupled channel analysis of the elastic and inelastic scattering on 12C in the framework of the rotator model yielded a good agreement between measured and calculated angular distributions. The determined quadrupole deformation parameter β2 = -0.67 agrees well with values from the literature. The existence of different qudrupole deformations for the central and spin-orbit components of the optical potential was studied. Large differences for the quadrupole deformations β2sup(c) and β2sup(so) were found at 8.9, 11.9, and 12.9 MeV. Especially at 8.9 MeV by this a great improvement of the fit to the data was reached. (orig./HSI)

  8. Total organic carbon analyzer

    Science.gov (United States)

    Godec, Richard G.; Kosenka, Paul P.; Smith, Brian D.; Hutte, Richard S.; Webb, Johanna V.; Sauer, Richard L.

    1991-01-01

    The development and testing of a breadboard version of a highly sensitive total-organic-carbon (TOC) analyzer are reported. Attention is given to the system components including the CO2 sensor, oxidation reactor, acidification module, and the sample-inlet system. Research is reported for an experimental reagentless oxidation reactor, and good results are reported for linearity, sensitivity, and selectivity in the CO2 sensor. The TOC analyzer is developed with gravity-independent components and is designed for minimal additions of chemical reagents. The reagentless oxidation reactor is based on electrolysis and UV photolysis and is shown to be potentially useful. The stability of the breadboard instrument is shown to be good on a day-to-day basis, and the analyzer is capable of 5 sample analyses per day for a period of about 80 days. The instrument can provide accurate TOC and TIC measurements over a concentration range of 20 ppb to 50 ppm C.

  9. An Automatic Engine Analyzer.

    Science.gov (United States)

    Tian-Fu, Li; And Others

    1984-01-01

    Describes an inexpensive, simple, microprocessor-based instrument which quickly and accurately measures and displays the indicated power and the pressure-volume indicator diagram of a reciprocating compressor or internal combustion engine. Hardware requirements, software considerations, and the instrument's educational value are discussed. (JN)

  10. Ultrasensitive Atmospheric Analyzer for Miniature UAVs Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this SBIR Phase I effort, Los Gatos Research (LGR) proposes to develop a highly-accurate, lightweight, low-power gas analyzer for quantification of water vapor...

  11. List mode multichannel analyzer

    Science.gov (United States)

    Archer, Daniel E.; Luke, S. John; Mauger, G. Joseph; Riot, Vincent J.; Knapp, David A.

    2007-08-07

    A digital list mode multichannel analyzer (MCA) built around a programmable FPGA device for onboard data analysis and on-the-fly modification of system detection/operating parameters, and capable of collecting and processing data in very small time bins (<1 millisecond) when used in histogramming mode, or in list mode as a list mode MCA.

  12. Centrifugal analyzer development

    International Nuclear Information System (INIS)

    The development of the centrifuge fast analyzer (CFA) is reviewed. The development of a miniature CFA with computer data analysis is reported and applications for automated diagnostic chemical and hematological assays are discussed. A portable CFA system with microprocessor was adapted for field assays of air and water samples for environmental pollutants, including ammonia, nitrates, nitrites, phosphates, sulfates, and silica. 83 references

  13. Portable pulse height analyzing system

    International Nuclear Information System (INIS)

    Low power, battery operated, compact Portable Pulse Height Analyzing System/Multi Channel Analyzer (PMCA) has been designed and developed for monitoring the various low activity radioisotopes in situ. PMCA can also be used in mobile radiation monitoring vans, wherein, gamma spectrum data collected at different locations can be stored in the battery backed RAM disk and down-loaded on to the PC via a serial link. Designed primarily for measurement and analysis of isotope activity and for field experiments, it can be used with most of the radiation detectors used for pulse height spectrum analysis. PMCA is built around embedded PC hardware architecture wherein all the cards are made with state of the art technology with extensive use of SMT and ASICS. PMCA provides features comparable with standard laboratory models and enables computation of integral area, background area, net peak area, FWHM, peak centroid and energy calibration in the field. This paper describes Portable Pulse Height Analyzing System with focus on following features: a) Hardware implementation of well-known multi channel analyzer technique using embedded PC hardware architecture. b) Software implementation of spectrum acquisition and analysis using high level language namely, C. (author)

  14. Analyzed Using Statistical Moments

    International Nuclear Information System (INIS)

    Diffraction enhanced imaging (DEl) technique is a new x-ray imaging method derived from radiography. The method uses a monorheumetten x-ray beam and introduces an analyzer crystal between an object and a detector Narrow angular acceptance of the analyzer crystal generates an improved contrast over the evaluation radiography. While standart radiography can produce an 'absorption image', DEl produces 'apparent absorption' and 'apparent refraction' images with superior quality. Objects with similar absorption properties may not be distinguished with conventional techniques due to close absorption coefficients. This problem becomes more dominant when an object has scattering properties. A simple approach is introduced to utilize scattered radiation to obtain 'pure absorption' and 'pure refraction' images

  15. PhosphoSiteAnalyzer

    DEFF Research Database (Denmark)

    Bennetzen, Martin V; Cox, Jürgen; Mann, Matthias; Andersen, Jens S.

    2012-01-01

    Phosphoproteomic experiments are routinely conducted in laboratories worldwide, and because of the fast development of mass spectrometric techniques and efficient phosphopeptide enrichment methods, researchers frequently end up having lists with tens of thousands of phosphorylation sites for...... sets that have been subjected to kinase prediction using the previously published NetworKIN algorithm. NetworKIN applies sophisticated linear motif analysis and contextual network modeling to obtain kinase-substrate associations with high accuracy and sensitivity. PhosphoSiteAnalyzer provides an...

  16. Lear CAN analyzer

    OpenAIRE

    Peiró Ibañez, Felipe

    2013-01-01

    Since it was introduced in the automotive industry, the protocol CAN (Controller Area Network) has been widely used for its benefits. This has led many companies to offer several hardware and software solutions in order to monitor the communications that gives this protocol. The current master thesis presents the Lear CAN Analyzer as a software tool developed within the company LEAR Corporation. It is designed to be used in the automobile industry as a complement or substitute for other co...

  17. Analyzing business process management

    OpenAIRE

    Skjæveland, Børge

    2013-01-01

    Within the Oil & Gas Industry, the market is constantly growing more competitive, forcing companies to continually adapt to changes. Companies need to cut costs and improve the business efficiency. One way of successfully managing these challenges is to implement business process management in the organization. This thesis will analyze how Oceaneering Asset Integrity AS handled the implementation of a Business Process Management System and the effects it had on the employees. The main goal...

  18. Magnetoresistive Emulsion Analyzer

    OpenAIRE

    Lin, Gungun; Baraban, Larysa; Han, Luyang; Karnaushenko, Daniil; Makarov, Denys; Cuniberti, Gianaurelio; Schmidt, Oliver G.

    2013-01-01

    We realize a magnetoresistive emulsion analyzer capable of detection, multiparametric analysis and sorting of ferrofluid-containing nanoliter-droplets. The operation of the device in a cytometric mode provides high throughput and quantitative information about the dimensions and magnetic content of the emulsion. Our method offers important complementarity to conventional optical approaches involving ferrofluids, and paves the way to the development of novel compact tools for diagnostics and n...

  19. Radioisotope analyzer of barium

    International Nuclear Information System (INIS)

    Principle of operation and construction of radioisotope barium sulphate analyzer type MZB-2 for fast determination of barium sulphate content in barite ores and enrichment products are described. The gauge equipped with Am-241 and a scintillation detector enables measurement of barium sulphate content in prepared samples of barite ores in the range 60% - 100% with the accuracy of 1%. The gauge is used in laboratories of barite mine and ore processing plant. 2 refs., 2 figs., 1 tab. (author)

  20. IPv6 Protocol Analyzer

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    With the emerging of next generation Intemet protocol (IPv6), it is expected to replace the current version of Internet protocol (IPv4) that will be exhausted in the near future. Besides providing adequate address space, some other new features are included into the new 128 bits of IP such as IP auto configuration, quality of service, simple routing capability, security, mobility and multicasting. The current protocol analyzer will not be able to handle IPv6 packets. This paper will focus on developing protocol analyzer that decodes IPv6 packet. IPv6 protocol analyzer is an application module,which is able to decode the IPv6 packet and provide detail breakdown of the construction of the packet. It has to understand the detail construction of the IPv6, and provide a high level abstraction of bits and bytes of the IPv6 packet.Thus it increases network administrators' understanding of a network protocol,helps he/she in solving protocol related problem in a IPv6 network environment.

  1. Analyzing and modeling heterogeneous behavior

    Science.gov (United States)

    Lin, Zhiting; Wu, Xiaoqing; He, Dongyue; Zhu, Qiang; Ni, Jixiang

    2016-05-01

    Recently, it was pointed out that the non-Poisson statistics with heavy tail existed in many scenarios of human behaviors. But most of these studies claimed that power-law characterized diverse aspects of human mobility patterns. In this paper, we suggest that human behavior may not be driven by identical mechanisms and can be modeled as a Semi-Markov Modulated Process. To verify our suggestion and model, we analyzed a total of 1,619,934 records of library visitations (including undergraduate and graduate students). It is found that the distribution of visitation intervals is well fitted with three sections of lines instead of the traditional power law distribution in log-log scale. The results confirm that some human behaviors cannot be simply expressed as power law or any other simple functions. At the same time, we divided the data into groups and extracted period bursty events. Through careful analysis in different groups, we drew a conclusion that aggregate behavior might be composed of heterogeneous behaviors, and even the behaviors of the same type tended to be different in different period. The aggregate behavior is supposed to be formed by "heterogeneous groups". We performed a series of experiments. Simulation results showed that we just needed to set up two states Semi-Markov Modulated Process to construct proper representation of heterogeneous behavior.

  2. Fluorescence analyzer for lignin

    Science.gov (United States)

    Berthold, John W.; Malito, Michael L.; Jeffers, Larry

    1993-01-01

    A method and apparatus for measuring lignin concentration in a sample of wood pulp or black liquor comprises a light emitting arrangement for emitting an excitation light through optical fiber bundles into a probe which has an undiluted sensing end facing the sample. The excitation light causes the lignin concentration to produce fluorescent emission light which is then conveyed through the probe to analyzing equipment which measures the intensity of the emission light. Measures a This invention was made with Government support under Contract Number DOE: DE-FC05-90CE40905 awarded by the Department of Energy (DOE). The Government has certain rights in this invention.

  3. Analyzing Chinese Financial Reporting

    Institute of Scientific and Technical Information of China (English)

    SABRINA; ZHANG

    2008-01-01

    If the world’s capital markets could use a harmonized accounting framework it would not be necessary for a comparison between two or more sets of accounting standards. However,there is much to do before this becomes reality.This article aims to pres- ent a general overview of China’s General Accepted Accounting Principles(GAAP), U.S.General Accepted Accounting Principles and International Financial Reporting Standards(IFRS),and to analyze the differ- ences among IFRS,U.S.GAAP and China GAAP using fixed assets as an example.

  4. Field Deployable DNA analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Wheeler, E; Christian, A; Marion, J; Sorensen, K; Arroyo, E; Vrankovich, G; Hara, C; Nguyen, C

    2005-02-09

    This report details the feasibility of a field deployable DNA analyzer. Steps for swabbing cells from surfaces and extracting DNA in an automatable way are presented. Since enzymatic amplification reactions are highly sensitive to environmental contamination, sample preparation is a crucial step to make an autonomous deployable instrument. We perform sample clean up and concentration in a flow through packed bed. For small initial samples, whole genome amplification is performed in the packed bed resulting in enough product for subsequent PCR amplification. In addition to DNA, which can be used to identify a subject, protein is also left behind, the analysis of which can be used to determine exposure to certain substances, such as radionuclides. Our preparative step for DNA analysis left behind the protein complement as a waste stream; we determined to learn if the proteins themselves could be analyzed in a fieldable device. We successfully developed a two-step lateral flow assay for protein analysis and demonstrate a proof of principle assay.

  5. Ring Image Analyzer

    Science.gov (United States)

    Strekalov, Dmitry V.

    2012-01-01

    Ring Image Analyzer software analyzes images to recognize elliptical patterns. It determines the ellipse parameters (axes ratio, centroid coordinate, tilt angle). The program attempts to recognize elliptical fringes (e.g., Newton Rings) on a photograph and determine their centroid position, the short-to-long-axis ratio, and the angle of rotation of the long axis relative to the horizontal direction on the photograph. These capabilities are important in interferometric imaging and control of surfaces. In particular, this program has been developed and applied for determining the rim shape of precision-machined optical whispering gallery mode resonators. The program relies on a unique image recognition algorithm aimed at recognizing elliptical shapes, but can be easily adapted to other geometric shapes. It is robust against non-elliptical details of the image and against noise. Interferometric analysis of precision-machined surfaces remains an important technological instrument in hardware development and quality analysis. This software automates and increases the accuracy of this technique. The software has been developed for the needs of an R&TD-funded project and has become an important asset for the future research proposal to NASA as well as other agencies.

  6. 电能质量分析仪谐波测量频谱分析长度检测%Method for test of FFT window width of voltage harmonic in power quality analyzers

    Institute of Scientific and Technical Information of China (English)

    蔡维; 何伟; 张红川; 王建伟

    2013-01-01

    The length of spectrum analysis test about harmonic analysis in power quality analyzer has been studied. The method is in accordance with the harmonic measurement request of standard and the harmonic analysis theory. The core is to test the frequency resolution which can be reacted from the output values. We need to detect the harmonic subgroup measurement according to the grouping theory. And we also check the weighting form which can realize by the different spectral leakage using rectangular weighting and others. After knowing these we can know the window width. The correctness of this method and the viability of this solution have been verified by many test experiments.%提出了一种电能质量分析仪谐波测量频谱分析长度的检测方案.根据国家标准对谐波测量的要求和谐波分析的软硬件原理得出通过检测频率分辨率达到检测目的的方法,这需要检测仪器是否采用谐波子组测量和矩形加权窗函数.文中根据分组的原理得出子组测量的检测方法;根据傅里叶变换、频谱泄露和栅栏效应的原理得出频率分辨率的检测方法;根据加窗函数减少频谱泄露的原理,通过公式推导和Matlab计算得出检测加窗算法的方法.综合以上实现电能质量分析仪频谱分析长度的检测.并通过大量的实验验证了该检测方法的正确性和检测方案的可行性.

  7. Residual gas analyzer calibration

    Science.gov (United States)

    Lilienkamp, R. H.

    1972-01-01

    A technique which employs known gas mixtures to calibrate the residual gas analyzer (RGA) is described. The mass spectra from the RGA are recorded for each gas mixture. This mass spectra data and the mixture composition data each form a matrix. From the two matrices the calibration matrix may be computed. The matrix mathematics requires the number of calibration gas mixtures be equal to or greater than the number of gases included in the calibration. This technique was evaluated using a mathematical model of an RGA to generate the mass spectra. This model included shot noise errors in the mass spectra. Errors in the gas concentrations were also included in the valuation. The effects of these errors was studied by varying their magnitudes and comparing the resulting calibrations. Several methods of evaluating an actual calibration are presented. The effects of the number of gases in then, the composition of the calibration mixture, and the number of mixtures used are discussed.

  8. Analyzing business models

    DEFF Research Database (Denmark)

    Nielsen, Christian

    2014-01-01

    New types of disclosure and reporting are argued to be vital in order to convey a transparent picture of the true state of the company. However, they are unfortunately not without problems as these types of information are somewhat more complex than the information provided in the traditional......, because the costs of processing and analyzing it exceed the benefits indicating bounded rationality. Hutton (2002) concludes that the analyst community’s inability to raise important questions on quality of management and the viability of its business model inevitably led to the Enron debacle. There seems...... to be evidence of the fact that all types of corporate stakeholders from management to employees, owners, the media and politicians have grave difficulties in interpreting new forms of reporting. One hypothesis could be that if managements’ own understanding of value creation is disclosed to the...

  9. Analyzing architecture articles

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In the present study, we express the quality, function, and characteristics of architecture to help people comprehensively understand what architecture is. We also reveal the problems and conflict found in population, land, water resources, pollution, energy, and the organization systems in construction. China’s economy is transforming. We should focus on the cities, architectural environment, energy conservation, emission-reduction, and low-carbon output that will result in successful green development. We should macroscopically and microscopically analyze the development, from the natural environment to the artificial environment; from the relationship between human beings and nature to the combination of social ecology in cities, and farmlands. We must learn to develop and control them harmoniously and scientifically to provide a foundation for the methods used in architecture research.

  10. Compact Microwave Fourier Spectrum Analyzer

    Science.gov (United States)

    Savchenkov, Anatoliy; Matsko, Andrey; Strekalov, Dmitry

    2009-01-01

    A compact photonic microwave Fourier spectrum analyzer [a Fourier-transform microwave spectrometer, (FTMWS)] with no moving parts has been proposed for use in remote sensing of weak, natural microwave emissions from the surfaces and atmospheres of planets to enable remote analysis and determination of chemical composition and abundances of critical molecular constituents in space. The instrument is based on a Bessel beam (light modes with non-zero angular momenta) fiber-optic elements. It features low power consumption, low mass, and high resolution, without a need for any cryogenics, beyond what is achievable by the current state-of-the-art in space instruments. The instrument can also be used in a wide-band scatterometer mode in active radar systems.

  11. Pseudostupidity and analyzability.

    Science.gov (United States)

    Cohn, L S

    1989-01-01

    This paper seeks to heighten awareness of pseudostupidity and the potential analyzability of patients who manifest it by defining and explicating it, reviewing the literature, and presenting in detail the psychoanalytic treatment of a pseudostupid patient. Pseudostupidity is caused by an inhibition of the integration and synthesis of thoughts resulting in a discrepancy between intellectual capacity and apparent intellect. The patient's pseudostupidity was determined in part by his need to prevent his being more successful than father, i.e., defeating his oedipal rival. Knowing and learning were instinctualized. The patient libidinally and defensively identified with father's passive, masochistic position. He needed to frustrate the analyst as he had felt excited and frustrated by his parents' nudity and thwarted by his inhibitions. He wanted to cause the analyst to feel as helpless as he, the patient, felt. Countertransference frustration was relevant and clinically useful in the analysis. Interpretation of evolving relevant issues led to more anxiety and guilt, less pseudostupidity, a heightened alliance, and eventual working through. Negative therapeutic reactions followed the resolution of pseudostupidity. PMID:2708771

  12. Downhole Fluid Analyzer Development

    Energy Technology Data Exchange (ETDEWEB)

    Bill Turner

    2006-11-28

    A novel fiber optic downhole fluid analyzer has been developed for operation in production wells. This device will allow real-time determination of the oil, gas and water fractions of fluids from different zones in a multizone or multilateral completion environment. The device uses near infrared spectroscopy and induced fluorescence measurement to unambiguously determine the oil, water and gas concentrations at all but the highest water cuts. The only downhole components of the system are the fiber optic cable and windows. All of the active components--light sources, sensors, detection electronics and software--will be located at the surface, and will be able to operate multiple downhole probes. Laboratory testing has demonstrated that the sensor can accurately determine oil, water and gas fractions with a less than 5 percent standard error. Once installed in an intelligent completion, this sensor will give the operating company timely information about the fluids arising from various zones or multilaterals in a complex completion pattern, allowing informed decisions to be made on controlling production. The research and development tasks are discussed along with a market analysis.

  13. Nonlinear dynamical systems analyzer

    Science.gov (United States)

    Coffey, Adrian S.; Johnson, Martin; Jones, Robin

    1994-10-01

    Computationally intensive algorithms are an ever more common requirement of modern signal processing. Following the work of Gentleman and Kung, McWhirter, Shepherd and Proudler suggested that certain matrix-orientated algorithms can be mapped onto systolic array architectures for adaptive linear signal processing. This has been extended by Broomhead et al. to the calculation of nonlinear predictive models and applied by Jones et al. to target identification and recognition. We shall show that predictive models are extremely sharp discriminators. Our chosen problem, if implemented as a systolic array, would require 3403 processors which would result in high through-put rate at excessive cost. We are developing an efficient sub-optimally implemented systolic array; one processor servicing more than one systolic node. We describe a prototype Heuristic Processor which computes a multi- dimensional, nonlinear, predictive model. It consists of a Radial Basis Function Network and a least squares optimizer using QR decomposition. The optimized solution of a set of simultaneous equations in 81 unknowns is calculated in 150 (mu) S. The QR section emulates a triangular systolic array by the novel use of an array of 40 mature silicon DSP chips costing under DOL100 each. The DSP chips operate in synchronism at a 50 MHz clock rate passing data to each other through multi-port memories on a dead-letter box principle; there are no memory access conflicts and only two-port and three-port memories are required. The processor provides 1-GFlop of computing power per cubic-foot of electronics for a component cost of approximately DOL15,000.

  14. Analyzing Pseudophosphatase Function.

    Science.gov (United States)

    Hinton, Shantá D

    2016-01-01

    Pseudophosphatases regulate signal transduction cascades, but their mechanisms of action remain enigmatic. Reflecting this mystery, the prototypical pseudophosphatase STYX (phospho-serine-threonine/tyrosine-binding protein) was named with allusion to the river of the dead in Greek mythology to emphasize that these molecules are "dead" phosphatases. Although proteins with STYX domains do not catalyze dephosphorylation, this in no way precludes their having other functions as integral elements of signaling networks. Thus, understanding their roles in signaling pathways may mark them as potential novel drug targets. This chapter outlines common strategies used to characterize the functions of pseudophosphatases, using as an example MK-STYX [mitogen-activated protein kinase (MAPK) phospho-serine-threonine/tyrosine binding], which has been linked to tumorigenesis, apoptosis, and neuronal differentiation. We start with the importance of "restoring" (when possible) phosphatase activity in a pseudophosphatase so that the active mutant may be used as a comparison control throughout immunoprecipitation and mass spectrometry analyses. To this end, we provide protocols for site-directed mutagenesis, mammalian cell transfection, co-immunoprecipitation, phosphatase activity assays, and immunoblotting that we have used to investigate MK-STYX and the active mutant MK-STYXactive. We also highlight the importance of utilizing RNA interference (RNAi) "knockdown" technology to determine a cellular phenotype in various cell lines. Therefore, we outline our protocols for introducing short hairpin RNA (shRNA) expression plasmids into mammalians cells and quantifying knockdown of gene expression with real-time quantitative PCR (qPCR). A combination of cellular, molecular, biochemical, and proteomic techniques has served as powerful tools in identifying novel functions of the pseudophosphatase MK-STYX. Likewise, the information provided here should be a helpful guide to elucidating the

  15. Digital Microfluidics Sample Analyzer

    Science.gov (United States)

    Pollack, Michael G.; Srinivasan, Vijay; Eckhardt, Allen; Paik, Philip Y.; Sudarsan, Arjun; Shenderov, Alex; Hua, Zhishan; Pamula, Vamsee K.

    2010-01-01

    Three innovations address the needs of the medical world with regard to microfluidic manipulation and testing of physiological samples in ways that can benefit point-of-care needs for patients such as premature infants, for which drawing of blood for continuous tests can be life-threatening in their own right, and for expedited results. A chip with sample injection elements, reservoirs (and waste), droplet formation structures, fluidic pathways, mixing areas, and optical detection sites, was fabricated to test the various components of the microfluidic platform, both individually and in integrated fashion. The droplet control system permits a user to control droplet microactuator system functions, such as droplet operations and detector operations. Also, the programming system allows a user to develop software routines for controlling droplet microactuator system functions, such as droplet operations and detector operations. A chip is incorporated into the system with a controller, a detector, input and output devices, and software. A novel filler fluid formulation is used for the transport of droplets with high protein concentrations. Novel assemblies for detection of photons from an on-chip droplet are present, as well as novel systems for conducting various assays, such as immunoassays and PCR (polymerase chain reaction). The lab-on-a-chip (a.k.a., lab-on-a-printed-circuit board) processes physiological samples and comprises a system for automated, multi-analyte measurements using sub-microliter samples of human serum. The invention also relates to a diagnostic chip and system including the chip that performs many of the routine operations of a central labbased chemistry analyzer, integrating, for example, colorimetric assays (e.g., for proteins), chemiluminescence/fluorescence assays (e.g., for enzymes, electrolytes, and gases), and/or conductometric assays (e.g., for hematocrit on plasma and whole blood) on a single chip platform.

  16. Computer-based radionuclide analyzer system

    International Nuclear Information System (INIS)

    The radionuclide analysis in nuclear power plants, practiced for the purpose of monitoring the quality of the primary loop water, the confirmation of the performance of reactor cleanup system and monitoring the radioactive waste effluent, is an important job. Important as it is, it requires considerable labor of experts, because the samples to be analyzed are multifarious and very large in number, and in addition, this job depends much on manual work. With a view of saving the labor, simplifying and standardizing the work, reducing radiation exposure, and automatizing the work of analysis, the computerized analyzer system has been worked out. The results of its performance test at the operating power plant have proved that the development has fairly accomplished the objects and that the system is well useful. The developmental work was carried out by the cooperation between The Tokyo Electric Power Co. and Toshiba in about 4 years from 1974 to this year. (auth.)

  17. A tandem parallel plate analyzer

    International Nuclear Information System (INIS)

    By a new modification of a parallel plate analyzer the second-order focus is obtained in an arbitrary injection angle. This kind of an analyzer with a small injection angle will have an advantage of small operational voltage, compared to the Proca and Green analyzer where the injection angle is 30 degrees. Thus, the newly proposed analyzer will be very useful for the precise energy measurement of high energy particles in MeV range. (author)

  18. Analyzing WMAP Observation by Quantum Gravity

    CERN Document Server

    Hamada, Ken-ji; Sugiyama, Naoshi; Yukawa, Tetsuyuki

    2007-01-01

    The angular power spectra of cosmic microwave background are analyzed under the light of the evolutional scenario of the universe based on the renormalizable quantum theory of gravity in four dimensions. The equation of evolution is solved numerically fixing the power law spectrum predicted by the conformal gravity for the initial condition. The equation requires to introduce a dynamical energy scale about 10^{17}GeV, where the inflationary space-time evolution makes a transition to the big-bang of the conventional Friedmann universe. The quality of fit to the three-year data of WMAP implies the possibility to understand the observation by quantum gravity.

  19. Analyzing Valuation Practices through Contracts

    DEFF Research Database (Denmark)

    Tesnière, Germain; Labatut, Julie; Boxenbaum, Eva

    This paper seeks to analyze the most recent changes in how societies value animals. We analyze this topic through the prism of contracts between breeding companies and farmers. Focusing on new valuation practices and qualification of breeding animals, we question the evaluation of difficult...

  20. Analyzing data files in SWAN

    CERN Document Server

    Gajam, Niharika

    2016-01-01

    Traditionally analyzing data happens via batch-processing and interactive work on the terminal. The project aims to provide another way of analyzing data files: A cloud-based approach. It aims to make it a productive and interactive environment through the combination of FCC and SWAN software.

  1. Analyzing transient instability phenomena beyond the classical stability boundary

    OpenAIRE

    Ali, Mahmoud; Glavic, Mevludin; Buisson, Jean; Wehenkel, Louis; Ernst, Damien

    2008-01-01

    We consider power systems for which the amount of power produced by their individual power plants is small with respect to the total generation of the system, and analyze how the transient instability mechanisms of these systems change qualitatively when their size or the dispersion of their generators increases. Simulation results show that loss of synchronism will propagate more slowly and even stop propagating. Given the evolution of power systems towards more dispersed generation and geog...

  2. The Krsko NPP Analyzer - phase II

    International Nuclear Information System (INIS)

    During the assessment of the nuclear safety level in Slovenia the SNSA (Slovenian Nuclear Safety Administration) found a need to gain a software support for analyzing the transients of the Krsko Nuclear Power Plant. Combining the RELAP5 code with graphical interface NPA (Nuclear Plant Analyzer) management staff saw an opportunity to have a powerful instrument for analyses and calculations on a user friendly basis and to get familiar with RELAP5 input deck without extra costs. At the beginning the project started with first phase, where Jozef Stefan Institute - OR4 formed a basic scope of the work and prepared the demo version of the SBLOCA on the basis of RELAP5/Mod3.1code input deck. Tractebel was chosen as a supplier of the project's second phase on the base of public bid. In 1996 the work started with translation of the input model from version Mod2.5 to Mod3.2 with standard routines and small final corrections. After this phase of the project a user of the Krsko NPP Analyzer can run accidents as SBLOCA, Main Steam Line Break, Feedwater Line Break, SGTR, and many other transients activating and combining interactive commands, starting from a full power operation. The third phase is planed. The SNSA has plans to improve the model of the Krsko NPP for a better simulation of core phenomena and to have detailed models of safety and auxiliary systems for increasing the number of possible transients and failures. The Critical Safety Function window will be created as a special mask. The analyzer will be used for education of employees and external experts, who are engaged in case of an emergency, to get familiar with the NPP systems and their operation. During the assessment of the nuclear safety level in Slovenia the SNSA (Slovenian Nuclear Safety Administration) found a need to gain a software support for analyzing the transients of the Krsko Nuclear Power Plant. Combining the RELAP5 code with graphical interface NPA (Nuclear Plant Analyzer) management staff saw an

  3. Nuclear fuel microsphere gamma analyzer

    Science.gov (United States)

    Valentine, Kenneth H.; Long, Jr., Ernest L.; Willey, Melvin G.

    1977-01-01

    A gamma analyzer system is provided for the analysis of nuclear fuel microspheres and other radioactive particles. The system consists of an analysis turntable with means for loading, in sequence, a plurality of stations within the turntable; a gamma ray detector for determining the spectrum of a sample in one section; means for analyzing the spectrum; and a receiver turntable to collect the analyzed material in stations according to the spectrum analysis. Accordingly, particles may be sorted according to their quality; e.g., fuel particles with fractured coatings may be separated from those that are not fractured, or according to other properties.

  4. SCAN: a Fortran syntax analyzer

    International Nuclear Information System (INIS)

    SCAN is a computer program which analyzes the syntax of a Fortran program. It reads statements of a Fortran program, checks the grammatical validity of them, and produces tables of the analyzed results and intermediate codes for further use. SCAN recognizes the Fortran syntax of the Japan Industrial Standards-7000, plus some Fortran-H statements. In this report, the structure of SCAN, the methods used by the SCAN to analyze statements, tables and intermediate Buckus form texts produced by the SCAN, are presented. The SCAN itself is also written in Fortran language and consists of about 5000 statements. By slight modifications the SCAN may be useful for any application which needs analysis operations of Fortran syntax. (author)

  5. Analyzer of neutron flux in real time

    International Nuclear Information System (INIS)

    With base in the study of the real signals of neutron flux of instability events occurred in the Laguna Verde nuclear power plant where the nucleus oscillation phenomena of the reactor are in the 0 to 2.5 Hz range, it has been seen the possibility about the development a surveillance and diagnostic equipment capable to analyze in real time the behavior of nucleus in this frequencies range. An important method for surveillance the stability of the reactor nucleus is the use of the Power spectral density which allows to determine the frequencies and amplitudes contained in the signals. It is used an instrument carried out by LabVIEW graphic programming with a data acquisition card of 16 channels which works at Windows 95/98 environment. (Author)

  6. Analyzing the Grammar of English

    CERN Document Server

    Teschner, Richard V

    2007-01-01

    Analyzing the Grammar of English offers a descriptive analysis of the indispensable elements of English grammar. Designed to be covered in one semester, this textbook starts from scratch and takes nothing for granted beyond a reading and speaking knowledge of English. Extensively revised to function better in skills-building classes, it includes more interspersed exercises that promptly test what is taught, simplified and clarified explanations, greatly expanded and more diverse activities, and a new glossary of over 200 technical terms.Analyzing the Grammar of English is the only English gram

  7. Nonlinear single-spin spectrum analyzer.

    Science.gov (United States)

    Kotler, Shlomi; Akerman, Nitzan; Glickman, Yinnon; Ozeri, Roee

    2013-03-15

    Qubits have been used as linear spectrum analyzers of their environments. Here we solve the problem of nonlinear spectral analysis, required for discrete noise induced by a strongly coupled environment. Our nonperturbative analytical model shows a nonlinear signal dependence on noise power, resulting in a spectral resolution beyond the Fourier limit as well as frequency mixing. We develop a noise characterization scheme adapted to this nonlinearity. We then apply it using a single trapped ion as a sensitive probe of strong, non-Gaussian, discrete magnetic field noise. Finally, we experimentally compared the performance of equidistant vs Uhrig modulation schemes for spectral analysis. PMID:25166519

  8. Mobile Greenhouse Gas Flux Analyzer for Unmanned Aerial Vehicles Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Los Gatos Research (LGR) proposes to develop highly-accurate, lightweight, low-power gas analyzers for measurements of carbon dioxide (CO2) and water vapor (H2O)...

  9. Mobile Greenhouse Gas Flux Analyzer for Unmanned Aerial Vehicles Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this SBIR Phase I effort, Los Gatos Research (LGR) proposes to develop a highly-accurate, lightweight, low-power gas analyzer for eddy flux covariance...

  10. Analyzing Software Piracy in Education.

    Science.gov (United States)

    Lesisko, Lee James

    This study analyzes the controversy of software piracy in education. It begins with a real world scenario that presents the setting and context of the problem. The legalities and background of software piracy are explained and true court cases are briefly examined. Discussion then focuses on explaining why individuals and organizations pirate…

  11. Helping Students Analyze Business Documents.

    Science.gov (United States)

    Devet, Bonnie

    2001-01-01

    Notes that student writers gain greater insight into the importance of audience by analyzing business documents. Discusses how business writing teachers can help students understand the rhetorical refinements of writing to an audience. Presents an assignment designed to lead writers systematically through an analysis of two advertisements. (SG)

  12. Software-Design-Analyzer System

    Science.gov (United States)

    Tausworthe, Robert C.

    1991-01-01

    CRISP-90 software-design-analyzer system, update of CRISP-80, is set of computer programs constituting software tool for design and documentation of other software and supporting top-down, hierarchical, modular, structured methodologies for design and programming. Written in Microsoft QuickBasic.

  13. FORTRAN Static Source Code Analyzer

    Science.gov (United States)

    Merwarth, P.

    1984-01-01

    FORTRAN Static Source Code Analyzer program, SAP (DEC VAX version), automatically gathers statistics on occurrences of statements and structures within FORTRAN program and provides reports of those statistics. Provisions made for weighting each statistic and provide an overall figure of complexity.

  14. The Statistical Loop Analyzer (SLA)

    Science.gov (United States)

    Lindsey, W. C.

    1985-01-01

    The statistical loop analyzer (SLA) is designed to automatically measure the acquisition, tracking and frequency stability performance characteristics of symbol synchronizers, code synchronizers, carrier tracking loops, and coherent transponders. Automated phase lock and system level tests can also be made using the SLA. Standard baseband, carrier and spread spectrum modulation techniques can be accomodated. Through the SLA's phase error jitter and cycle slip measurements the acquisition and tracking thresholds of the unit under test are determined; any false phase and frequency lock events are statistically analyzed and reported in the SLA output in probabilistic terms. Automated signal drop out tests can be performed in order to trouble shoot algorithms and evaluate the reacquisition statistics of the unit under test. Cycle slip rates and cycle slip probabilities can be measured using the SLA. These measurements, combined with bit error probability measurements, are all that are needed to fully characterize the acquisition and tracking performance of a digital communication system.

  15. Methods for Analyzing Social Media

    DEFF Research Database (Denmark)

    Jensen, Jakob Linaa

    2013-01-01

    Social media is becoming increasingly attractive for users. It is a fast way to communicate ideas and a key source of information. It is therefore one of the most influential mediums of communication of our time and an important area for audience research. The growth of social media invites many...... new questions such as: How can we analyze social media? Can we use traditional audience research methods and apply them to online content? Which new research strategies have been developed? Which ethical research issues and controversies do we have to pay attention to? This book focuses on research...... strategies and methods for analyzing social media and will be of interest to researchers and practitioners using social media, as well as those wanting to keep up to date with the subject....

  16. Source-Code-Analyzing Program

    Science.gov (United States)

    Manteufel, Thomas; Jun, Linda

    1991-01-01

    FORTRAN Static Source Code Analyzer program, SAP, developed to gather statistics automatically on occurrences of statements and structures within FORTRAN program and provide for reporting of those statistics. Provisions made to weight each statistic and provide overall figure of complexity. Statistics, as well as figures of complexity, gathered on module-by-module basis. Overall summed statistics also accumulated for complete input source file. Written in FORTRAN IV.

  17. Analyzing Big Data in Psychology: A Split/Analyze/Meta-Analyze Approach

    Science.gov (United States)

    Cheung, Mike W.-L.; Jak, Suzanne

    2016-01-01

    Big data is a field that has traditionally been dominated by disciplines such as computer science and business, where mainly data-driven analyses have been performed. Psychology, a discipline in which a strong emphasis is placed on behavioral theories and empirical research, has the potential to contribute greatly to the big data movement. However, one challenge to psychologists—and probably the most crucial one—is that most researchers may not have the necessary programming and computational skills to analyze big data. In this study we argue that psychologists can also conduct big data research and that, rather than trying to acquire new programming and computational skills, they should focus on their strengths, such as performing psychometric analyses and testing theories using multivariate analyses to explain phenomena. We propose a split/analyze/meta-analyze approach that allows psychologists to easily analyze big data. Two real datasets are used to demonstrate the proposed procedures in R. A new research agenda related to the analysis of big data in psychology is outlined at the end of the study. PMID:27242639

  18. Analyzing Big Data in Psychology: A Split/Analyze/Meta-Analyze Approach

    Directory of Open Access Journals (Sweden)

    Mike W.-L. Cheung

    2016-05-01

    Full Text Available Big data is a field that has traditionally been dominated by disciplines such as computer science and business, where mainly data-driven analyses have been performed. Psychology, a discipline in which a strong emphasis is placed on behavioral theories and empirical research, has the potential to contribute greatly to the big data movement. However, one challenge to psychologists – and probably the most crucial one – is that most researchers may not have the necessary programming and computational skills to analyze big data. In this study we argue that psychologists can also conduct big data research and that, rather than trying to acquire new programming and computational skills, they should focus on their strengths, such as performing psychometric analyses and testing theories using multivariate analyses to explain phenomena. We propose a split/analyze/meta-analyze approach that allows psychologists to easily analyze big data. Two real datasets are used to demonstrate the proposed procedures in R. A new research agenda related to the analysis of big data in psychology is outlined at the end of the study.

  19. Analyzing Big Data in Psychology: A Split/Analyze/Meta-Analyze Approach.

    Science.gov (United States)

    Cheung, Mike W-L; Jak, Suzanne

    2016-01-01

    Big data is a field that has traditionally been dominated by disciplines such as computer science and business, where mainly data-driven analyses have been performed. Psychology, a discipline in which a strong emphasis is placed on behavioral theories and empirical research, has the potential to contribute greatly to the big data movement. However, one challenge to psychologists-and probably the most crucial one-is that most researchers may not have the necessary programming and computational skills to analyze big data. In this study we argue that psychologists can also conduct big data research and that, rather than trying to acquire new programming and computational skills, they should focus on their strengths, such as performing psychometric analyses and testing theories using multivariate analyses to explain phenomena. We propose a split/analyze/meta-analyze approach that allows psychologists to easily analyze big data. Two real datasets are used to demonstrate the proposed procedures in R. A new research agenda related to the analysis of big data in psychology is outlined at the end of the study. PMID:27242639

  20. BWR plant analyzer development at BNL

    International Nuclear Information System (INIS)

    An engineering plant analyzer has been developed at BNL for realistically and accurately simulating transients and severe abnormal events in BWR power plants. Simulations are being carried out routinely with high fidelity, high simulation speed, at low cost and with unsurpassed user convenience. The BNL Plant Analyzer is the only operating facility which (a) simulates more than two orders-of-magnitude faster than the CDC-7600 mainframe computer, (b) is accessible and fully operational in on-line interactive mode, remotely from anywhere in the US, from Europe or the Far East (Korea), via widely available IBM-PC compatible personal computers, standard modems and telephone lines, (c) simulates both slow and rapid transients seven times faster than real-time speed in direct access, and four times faster in remote access modes, (d) achieves high simulation speed without compromising fidelity, and (e) is available to remote access users at the low cost of $160 per hour. The accomplishment of detailed and accurate simulations in complex power plants at high speed and low cost are due chiefly to two reasons. The first reason is the application of five distinct modeling principles [2] which are not employed in any other simulation code. The second, and even more important reason is the utilization of a special-purpose peripheral computer with its 13 task-specific parallel processors

  1. The security analyzer, a security analyzer program written in Prolog

    International Nuclear Information System (INIS)

    A technique has been developed to characterize a nuclear facility and measure the strengths and weaknesses of the physical protection system. It utilizes the artificial intelligence capabilities available in the prolog programming language to probe a facility's defenses and find potential attack paths that meet designated search criteria. As sensors or barriers become inactive due to maintenance, failure, or inclement weather conditions, the protection system can rapidly be reanalyzed to discover weaknesses that would need to be strengthened by alternative means. Conversely, proposed upgrades and enhancements can be easily entered into the database and their effect measured against a variety of potential adversary attacks. Thus the security analyzer is a tool that aids the protection planner as well as the protection operations staff

  2. Trace Gas Analyzer (TGA) program

    Science.gov (United States)

    1977-01-01

    The design, fabrication, and test of a breadboard trace gas analyzer (TGA) is documented. The TGA is a gas chromatograph/mass spectrometer system. The gas chromatograph subsystem employs a recirculating hydrogen carrier gas. The recirculation feature minimizes the requirement for transport and storage of large volumes of carrier gas during a mission. The silver-palladium hydrogen separator which permits the removal of the carrier gas and its reuse also decreases vacuum requirements for the mass spectrometer since the mass spectrometer vacuum system need handle only the very low sample pressure, not sample plus carrier. System performance was evaluated with a representative group of compounds.

  3. Fuel analyzer; Analisador de combustiveis

    Energy Technology Data Exchange (ETDEWEB)

    Cozzolino, Roberval [RS Motors, Indaiatuba, SP (Brazil)

    2008-07-01

    The current technology 'COMBUSTIMETRO' aims to examine the fuel through performance of the engine, as the role of the fuel is to produce energy for the combustion engine in the form of which is directly proportional to the quality and type of fuel. The 'COMBUSTIMETRO' has an engine that always keeps the same entry of air, fuel and fixed point of ignition. His operation is monitored by sensors (Sonda Lambda, RPM and Gases Analyzer) connected to a processor that performs calculations and records the information, generate reports and graphs. (author)

  4. Truck acoustic data analyzer system

    Science.gov (United States)

    Haynes, Howard D.; Akerman, Alfred; Ayers, Curtis W.

    2006-07-04

    A passive vehicle acoustic data analyzer system having at least one microphone disposed in the acoustic field of a moving vehicle and a computer in electronic communication the microphone(s). The computer detects and measures the frequency shift in the acoustic signature emitted by the vehicle as it approaches and passes the microphone(s). The acoustic signature of a truck driving by a microphone can provide enough information to estimate the truck speed in miles-per-hour (mph), engine speed in rotations-per-minute (RPM), turbocharger speed in RPM, and vehicle weight.

  5. COBSTRAN - COMPOSITE BLADE STRUCTURAL ANALYZER

    Science.gov (United States)

    Aiello, R. A.

    1994-01-01

    The COBSTRAN (COmposite Blade STRuctural ANalyzer) program is a pre- and post-processor that facilitates the design and analysis of composite turbofan and turboprop blades, as well as composite wind turbine blades. COBSTRAN combines composite mechanics and laminate theory with a data base of fiber and matrix properties. As a preprocessor for NASTRAN or another Finite Element Method (FEM) program, COBSTRAN generates an FEM model with anisotropic homogeneous material properties. Stress output from the FEM program is provided as input to the COBSTRAN postprocessor. The postprocessor then uses the composite mechanics and laminate theory routines to calculate individual ply stresses, strains, interply stresses, thru-the-thickness stresses and failure margins. COBSTRAN is designed to carry out the many linear analyses required to efficiently model and analyze blade-like structural components made of multilayered angle-plied fiber composites. Components made from isotropic or anisotropic homogeneous materials can also be modeled as a special case of COBSTRAN. NASTRAN MAT1 or MAT2 material cards are generated according to user supplied properties. COBSTRAN is written in FORTRAN 77 and was implemented on a CRAY X-MP with a UNICOS 5.0.12 operating system. The program requires either COSMIC NASTRAN or MSC NASTRAN as a structural analysis package. COBSTRAN was developed in 1989, and has a memory requirement of 262,066 64 bit words.

  6. Managing healthcare information: analyzing trust.

    Science.gov (United States)

    Söderström, Eva; Eriksson, Nomie; Åhlfeldt, Rose-Mharie

    2016-08-01

    Purpose - The purpose of this paper is to analyze two case studies with a trust matrix tool, to identify trust issues related to electronic health records. Design/methodology/approach - A qualitative research approach is applied using two case studies. The data analysis of these studies generated a problem list, which was mapped to a trust matrix. Findings - Results demonstrate flaws in current practices and point to achieving balance between organizational, person and technology trust perspectives. The analysis revealed three challenge areas, to: achieve higher trust in patient-focussed healthcare; improve communication between patients and healthcare professionals; and establish clear terminology. By taking trust into account, a more holistic perspective on healthcare can be achieved, where trust can be obtained and optimized. Research limitations/implications - A trust matrix is tested and shown to identify trust problems on different levels and relating to trusting beliefs. Future research should elaborate and more fully address issues within three identified challenge areas. Practical implications - The trust matrix's usefulness as a tool for organizations to analyze trust problems and issues is demonstrated. Originality/value - Healthcare trust issues are captured to a greater extent and from previously unchartered perspectives. PMID:27477934

  7. The Power War: Male Response to Power Loss under Equality.

    Science.gov (United States)

    Kahn, Arnold

    1984-01-01

    Analyzes the male response to anticipated loss of power as women continue to demand equality and equal power. Describes the scope of male power, and analyzes the importance of power to men in terms of the male sex-role stereotype. Hypothesizes some likely male responses to a loss of power. (BH)

  8. Tensor Ayy and vector Ay analyzing powers in the 1H(d, d')X and 12C(d, d')X reactions at initial deuteron momenta of 9 GeV/c in the region of baryonic resonance excitation

    International Nuclear Information System (INIS)

    The angular dependence of the tensor Ayy and vector Ay analyzing powers in the inelastic scattering of deuterons with a momentum of 9.0 GeV/c on hydrogen and carbon has been measured. The range of measurements corresponds to the baryonic resonance excitation with masses of ∼2.2-2.6 GeV/c2. The Ayy data, being in good agreement with the previous results, demonstrate an approximate t scaling up to -1.5 (GeV/c)2. The large values of Ay show a significant role of the spin-dependent part of the elementary amplitude of the NN → NN* reaction. The results of the experiment are compared with model predictions of the plane-wave impulse approximation

  9. Analyzing petabytes of data with Hadoop

    CERN Document Server

    CERN. Geneva

    2009-01-01

    Abstract The open source Apache Hadoop project provides a powerful suite of tools for storing and analyzing petabytes of data using commodity hardware. After several years of production use inside of web companies like Yahoo! and Facebook and nearly a year of commercial support and development by Cloudera, the technology is spreading rapidly through other disciplines, from financial services and government to life sciences and high energy physics. The talk will motivate the design of Hadoop and discuss some key implementation details in depth. It will also cover the major subprojects in the Hadoop ecosystem, go over some example applications, highlight best practices for deploying Hadoop in your environment, discuss plans for the future of the technology, and provide pointers to the many resources available for learning more. In addition to providing more information about the Hadoop platform, a major goal of this talk is to begin a dialogue with the ATLAS research team on how the tools commonly used in t...

  10. Los Alamos Nuclear plant analyzer

    International Nuclear Information System (INIS)

    The Relational Database software obtained from Idaho National Engineering Laboratory is implemented on the Los Alamos Cray computer system. For the Nuclear Plant Analyzer (NPA), Los Alamos retained a graphics display terminal and a separate forms terminal for mutual compatibility, but integrated both the terminals into a single-line full-duplex mode of communications, using a single keyboard for input. Work on the program-selection phase of an NPA session is well underway. The final phase of implementation will be the Worker or graphics-driver phase. The Los Alamos in-house NPA has been in use for some time, and has given good results in analyses of four transients. The NPA hydrocode has been developed in to a fast-running code. The authors have observed an average of a factor-of-3 speed increase for typical slow reactor-safety transients when employing the stability enhancing two-step (SETS) method in the one-dimensional components using PF1/MOD1. The SETS method allows violation of the material Courant time-step stability limit and is thus stable at large time steps. The SETS method to the three-dimensional VESSEL component in the NPA hydrocode has been adapted. In addition to the speed increase from this new software, significant additional speed is expected as a result of new hardware that provides for vectorization or parallelization

  11. A calibration free vector network analyzer

    Science.gov (United States)

    Kothari, Arpit

    Recently, two novel single-port, phase-shifter based vector network analyzer (VNA) systems were developed and tested at X-band (8.2--12.4 GHz) and Ka-band (26.4--40 GHz), respectively. These systems operate based on electronically moving the standing wave pattern, set up in a waveguide, over a Schottky detector and sample the standing wave voltage for several phase shift values. Once this system is fully characterized, all parameters in the system become known and hence theoretically, no other correction (or calibration) should be required to obtain the reflection coefficient, (Gamma), of an unknown load. This makes this type of VNA "calibration free" which is a significant advantage over other types of VNAs. To this end, a VNA system, based on this design methodology, was developed at X-band using several design improvements (compared to the previous designs) with the aim of demonstrating this "calibration-free" feature. It was found that when a commercial VNA (HP8510C) is used as the source and the detector, the system works as expected. However, when a detector is used (Schottky diode, log detector, etc.), obtaining correct Gamma still requires the customary three-load calibration. With the aim of exploring the cause, a detailed sensitivity analysis of prominent error sources was performed. Extensive measurements were done with different detection techniques including use of a spectrum analyzer as power detector. The system was tested even for electromagnetic compatibility (EMC) which may have contributed to this issue. Although desired results could not be obtained using the proposed standing-wave-power measuring devices like the Schottky diode but the principle of "calibration-free VNA" was shown to be true.

  12. CRISP90 - SOFTWARE DESIGN ANALYZER SYSTEM

    Science.gov (United States)

    Tausworthe, R. C.

    1994-01-01

    The CRISP90 Software Design Analyzer System, an update of CRISP-80, is a set of programs forming a software design and documentation tool which supports top-down, hierarchic, modular, structured design and programming methodologies. The quality of a computer program can often be significantly influenced by the design medium in which the program is developed. The medium must foster the expression of the programmer's ideas easily and quickly, and it must permit flexible and facile alterations, additions, and deletions to these ideas as the design evolves. The CRISP90 software design analyzer system was developed to provide the PDL (Programmer Design Language) programmer with such a design medium. A program design using CRISP90 consists of short, English-like textual descriptions of data, interfaces, and procedures that are imbedded in a simple, structured, modular syntax. The display is formatted into two-dimensional, flowchart-like segments for a graphic presentation of the design. Together with a good interactive full-screen editor or word processor, the CRISP90 design analyzer becomes a powerful tool for the programmer. In addition to being a text formatter, the CRISP90 system prepares material that would be tedious and error prone to extract manually, such as a table of contents, module directory, structure (tier) chart, cross-references, and a statistics report on the characteristics of the design. Referenced modules are marked by schematic logic symbols to show conditional, iterative, and/or concurrent invocation in the program. A keyword usage profile can be generated automatically and glossary definitions inserted into the output documentation. Another feature is the capability to detect changes that were made between versions. Thus, "change-bars" can be placed in the output document along with a list of changed pages and a version history report. Also, items may be marked as "to be determined" and each will appear on a special table until the item is

  13. Development of hydrazine analyzer for high concentration of ethanolamine

    International Nuclear Information System (INIS)

    A polarographic electrode method has been conventionally used for monitoring hydrazine concentrations in feedwater of pressurized water reactor (PWR) to control the secondary water chemistry. Measurements of hydrazine concentrations of the high pH controlled feedwater with ethanolamine (ETA) by this existing hydrazine analyzer were not stable on some occasions when the plant was in power operation. To solve this problem we developed a new hydrazine analyzer using p-dimethylaminobenzaldehyde (DABA) colorimetry and flow injection analysis (FIA) methods. (author)

  14. Update on the USNRC's Nuclear Plant Analyzer

    International Nuclear Information System (INIS)

    The Nuclear Plant Analyzer (NPA) is the US Nuclear Regulatory Commission's (NRC's) state-of-the-art nuclear reactor simulation capability. This computer software package integrates high fidelity nuclear reactor simulation codes such as the TRAC and RELAP5 series of codes with color graphics display techniques and advanced workstation hardware. An overview of this program was given at the 1984 Summer Computer Simulation Conference (SCSC), with selected topics discussed at the 1985 and 1986 SCSCs. Since the 1984 presentation, major redirections of this NRC program have been taken. The original NPA system was developed for operation on a Control Data Corporation CYBER 176 computer, technology that is some 10 to 15 years old. The NPA system has recently been implemented on Class VI computers to gain increased computational capabilities, and is now being implemented on super-minicomputers for use by the scientific community and possibly by the commercial nuclear power plant simulator community. This paper addresses these activities and related experiences. First, the Class VI computer implementation is discussed. The trade-offs between gaining significantly greater computational speed and central memory, with the loss of performance due to many more simultaneous users is shown. Second, the goal of the super-minicomputer implementation is to produce a very cost-effective system that utilizes advanced (multi-dimensional, two-phase coolant) simulation capabilities at real wall-clock simulation times. Benchmarking of the initial super-minicomputer implementation is discussed. Finally, the technical and economic feasibility is addressed for implementing the super-minicomputer version of the NPA with the RELAP5 simulation code onto the Black Fox full scope nuclear power plant simulator

  15. Emergency response training with the BNL plant analyzer

    International Nuclear Information System (INIS)

    Presented in the experience in the use of the BNL plant analyzer for NRC emergency response training to simulated accidents in a BWR. The unique features of the BNL Plant Analyzer that are important for the emergency response training are summarized. A closed-loop simulation of all the key systems of a power plant in question was found essential to the realism of the emergency drills conducted at NRC. The faster than real-time simulation speeds afforded by the BNL Plant Analyzer have demonstrated its usefulness for the timely conduct of the emergency response training

  16. Power generation

    International Nuclear Information System (INIS)

    In the second half of twentieth century, nuclear power became an industrial reality. Now the operating 433 power plants, the 37 plants under construction, near 9000 years/reactor with only one serious accident with emission of radioactive material to the environment (Chernobyl) show the maturity of this technology. Today nuclear power contribute a 17% to the global generation and an increase of 75 % of the demand of electricity is estimated for 2020 while this demand is expected to triplicate by 2050. How this requirement can be satisfied? All the indicators seems to demonstrate that nuclear power will be the solution because of the shortage of other sources, the increase of the prices of the non renewable fuels and the scarce contribution of the renewable ones. In addition, the climatic changes produced by the greenhouse effect make even more attractive nuclear power. The situation of Argentina is analyzed and compared with other countries. The convenience of an increase of nuclear power contribution to the total national generation seems clear and the conclusion of the construction of the Atucha II nuclear power plant is recommended

  17. Update on the USNRC's nuclear plant analyzer

    International Nuclear Information System (INIS)

    The Nuclear Plant Analyzer (NPA) is the U.S. Nuclear Regulatory Commission's (NRC's) state-of-the-art nuclear reactor simulation capability. This computer software package integrates high fidelity nuclear reactor simulation codes such as the TRAC and RELAPS series of codes with color graphics display techniques and advanced workstation hardware. An overview of this program was given at the 1984 Summer Computer Simulation Conference (SCSC), with selected topics discussed at the 1985 and 1986 SCSCs. This paper addresses these activities and related experiences. First, The Class VI computer implementation is discussed. The trade-offs between gaining significantly greater computational speed and central memory, with the loss of performance due to many more simultaneous users is shown. Second, the goal of the super-minicomputer implementation is to produce a very cost-effective system that utilizes advanced (multi-dimensional, two-phase coolant) simulation capabilities at real wall-clock simulation times. Benchmarking of the initial super-minicomputer implementation is discussed. Finally, the technical and economic feasibility is addressed for implementing the super-minicomputer version of the NPA with the RELAPS simulation code onto the Black Fox full scope nuclear power plant simulator

  18. TREAT Nuclear Plant Analyzer aids engineering and training

    International Nuclear Information System (INIS)

    Westinghouse's TREAT (Transient Real-time Engineering Analysis Tool) Nuclear Plant Analyzer combines a multi-purpose thermohydraulic code with a user-friendly, modular, real-time simulation environment. The system provides a powerful desk-top simulation and analysis tool with high resolution graphics for a fairly moderate investment. (author)

  19. Independence characteristics of concrete thinking form analyzed based on EEG power spectrum in α-frequency range%基于α频带脑电功率谱分析具象思维形式的独立性特征

    Institute of Scientific and Technical Information of China (English)

    魏玉龙; 尤海燕; 刘天君

    2012-01-01

    目的 通过脑电检测分析具象思维这种独具东方特色的思维方法,在α频带功率谱的变化,探寻其独立性特征.方法 选择69名在校大学生为受试对象,通过思维作业培训后,应用脑电同步检测具象思维、抽象思维、形象思维作业过程的脑电变化,应用功率谱分析方法,提取α频带(包含α1和α2两个频带)的相对功率,对3种思维形式和一般安静态进行比较.结果 α1频带,具象思维形式分布与一般安静态、形象思维形式、抽象思维形式之间比较,均有极显著性差异(P<0.001);3种思维形式与一般安静态区别明显,功率均高于一般安静态,3者并行排列分布,且无线性交叉,界限清楚,具象思维形式的空间分布特点表现出Fz高功率、01与F7趋于一致性、C3导联呈高功率反应.α2频带,具象思维形式与一般安静态之间比较,有极显著性差异(P <0.001),而与形象思维形式、抽象思维形式之间比较,无显著性差异(P>0.05);3种思维形式的相对功率值无显著性差异,但与一般安静态的差异显著,具象思维形式的空间分布表现为O2与T6导联表现高功率.结论 α频带从不同角度、程度上显示出3种思维形式之间的差异,显示出具象思维形式的独立性特征.%Objective To analyze concrete thinking with oriental characteristics by using electroencephalogram (EEG) examination, and discover the independence characteristics based on the changes of power spectrum in a-frequency range. Methods After training of mental tasks, 69 students from universities were selected, and their EEG changes were detected during the processes of concrete thinking, abstract thinking and thinking in images. The relative power was extracted from a-frequency range (including α1-frequency range and α2-frequency range) by applying power spectrum analysis. The three thinking forms were compared with common static state. Results In a,-frequency range, the

  20. Novel topological descriptors for analyzing biological networks

    Directory of Open Access Journals (Sweden)

    Varmuza Kurt K

    2010-06-01

    Full Text Available Abstract Background Topological descriptors, other graph measures, and in a broader sense, graph-theoretical methods, have been proven as powerful tools to perform biological network analysis. However, the majority of the developed descriptors and graph-theoretical methods does not have the ability to take vertex- and edge-labels into account, e.g., atom- and bond-types when considering molecular graphs. Indeed, this feature is important to characterize biological networks more meaningfully instead of only considering pure topological information. Results In this paper, we put the emphasis on analyzing a special type of biological networks, namely bio-chemical structures. First, we derive entropic measures to calculate the information content of vertex- and edge-labeled graphs and investigate some useful properties thereof. Second, we apply the mentioned measures combined with other well-known descriptors to supervised machine learning methods for predicting Ames mutagenicity. Moreover, we investigate the influence of our topological descriptors - measures for only unlabeled vs. measures for labeled graphs - on the prediction performance of the underlying graph classification problem. Conclusions Our study demonstrates that the application of entropic measures to molecules representing graphs is useful to characterize such structures meaningfully. For instance, we have found that if one extends the measures for determining the structural information content of unlabeled graphs to labeled graphs, the uniqueness of the resulting indices is higher. Because measures to structurally characterize labeled graphs are clearly underrepresented so far, the further development of such methods might be valuable and fruitful for solving problems within biological network analysis.

  1. Portable Programmable Multifunction Body Fluids Analyzer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Liquid Logic proposes to develop a very capable analyzer based on its digital microfluidic technology. Such an analyzer would be:  Capable of both...

  2. 46 CFR 154.1360 - Oxygen analyzer.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Oxygen analyzer. 154.1360 Section 154.1360 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS... Instrumentation § 154.1360 Oxygen analyzer. The vessel must have a portable analyzer that measures oxygen...

  3. BWR stability analysis with the BNL Engineering Plant Analyzer

    International Nuclear Information System (INIS)

    March 9, 1989 instability at the LaSalle-2 Power Plant and more than ninety related BWR transients have been simulated on the BNL Engineering Plant Analyzer (EPA). Power peaks were found to be potentially seventeen times greater than the rated power, flow reversal occurs momentarily during large power oscillations, the fuel centerline temperature oscillates between 1,030 and 2,090 K, while the cladding temperature oscillates between 560 and 570 K. The Suppression Pool reaches its specified temperature limit either never or in as little as 4.3 minutes, depending on operator actions and transient scenario. Thermohydraulic oscillations occur at low core coolant flow (both Recirculation Pumps tripped), with sharp axial or redial fission power peaking and with partial loss of feedwater preheating while the feedwater is flow kept high to maintain coolant inventory in the vessel. Effects from BOP system were shown to influence reactor stability strongly through dosed-loop resonance feedback. High feedwater flow and low temperature destabilize the reactor. Low feedwater flow restabilizes the reactor, because of steam condensation and feedwater preheating in the downcomer, which reduces effectively the destabilizing core inlet subcooling. The EPA has been found to be capable of analyzing BWR stability '' shown to be effective for scoping calculations and for supporting accident management

  4. Fast Decoupled Power Flow for Power System with High Voltage Direct Current Transmission Line System

    OpenAIRE

    Prechanon Kumkratug

    2010-01-01

    Problem statement: High voltage direct current transmission line system has been widely applied for control power flow in power system. The power flow analysis was the one of powerful tools by which the power system equipped was analyzed both for planning and operation strategies. Approach: This study presented the method to analyze power flow of power system consisted of HVDC system. HVDC was modeled as the complex power injections. The presented complex power injected was incorporated into ...

  5. Analyzing multimode wireless sensor networks using the network calculus

    OpenAIRE

    2015-01-01

    The network calculus is a powerful tool to analyze the performance of wireless sensor networks. But the original network calculus can only model the single-mode wireless sensor network. In this paper, we combine the original network calculus with the multimode model to analyze the maximum delay bound of the flow of interest in the multimode wireless sensor network. There are two combined methods A-MM and N-MM. The method A-MM models the whole network as a multimode component, and the method N...

  6. Wind energy system time-domain (WEST) analyzers

    Science.gov (United States)

    Dreier, M. E.; Hoffman, J. A.

    1981-01-01

    A portable analyzer which simulates in real time the complex nonlinear dynamics of horizontal axis wind energy systems was constructed. Math models for an aeroelastic rotor featuring nonlinear aerodynamic and inertial terms were implemented with high speed digital controllers and analog calculation. This model was combined with other math models of elastic supports, control systems, a power train and gimballed rotor kinematics. A stroboscopic display system graphically depicting distributed blade loads, motion, and other aerodynamic functions on a cathode ray tube is included. Limited correlation efforts showed good comparison between the results of this analyzer and other sophisticated digital simulations. The digital simulation results were successfully correlated with test data.

  7. Development of a pocket multi-channel analyzer

    International Nuclear Information System (INIS)

    A pocket Multi-Channel Analyzer, which is based on 20 pin SMT micro-controller, Serial Peripheral Interfaced ADC and FRAM, and MCU on chip timer/counter acting as de-dead-time clock, was developed and introduced in this paper. Pulse peak hold circuit, MCA timing, micro-controller application techniques, and a reliable simple schematic for peak detection was described as well. The protocol MCA is housed in 110 60 23 mm3. The analyzing resolution can be up to 16384 channels. The dead time is 17 μs when the resolution is programmed to be 1024 channels. It is powered from a single +5V supply, and the power consumption is 360 mW. It can be well embedded in various portable multi-channel spectrum equipments. (authors)

  8. PMD: A Resource for Archiving and Analyzing Protein Microarray data

    OpenAIRE

    Zhaowei Xu; Likun Huang; Hainan Zhang; Yang Li; Shujuan Guo; Nan Wang; Shi-hua Wang; Ziqing Chen; Jingfang Wang; Sheng-ce Tao

    2016-01-01

    Protein microarray is a powerful technology for both basic research and clinical study. However, because there is no database specifically tailored for protein microarray, the majority of the valuable original protein microarray data is still not publically accessible. To address this issue, we constructed Protein Microarray Database (PMD), which is specifically designed for archiving and analyzing protein microarray data. In PMD, users can easily browse and search the entire database by expe...

  9. High energy ion analyzer for laser-produced plasma studies

    International Nuclear Information System (INIS)

    A simple electrostatic deflection multi-channel time-of-flight ion analyzer optimized to study high energy ion species from laser-produced plasmas is described. For this application moderate species and energy resolution over a wide dynamic energy range is desirable. A dynamic energy range from 1 to 1000 keV per unit charge is achieved with a 20 kV power supply. Design considerations are presented together with some typical experimental results

  10. Terahertz bandwidth integrated radio frequency spectrum analyzer via nonlinear optics

    CERN Document Server

    Ferrera, Marcello; Pasquazi, Alessia; Peccianti, Marco; Clerici, Matteo; Caspani, Lucia; Chu, Sai T; Little, Brent E; Morandotti, Roberto; Moss, David J

    2014-01-01

    We report an integrated all-optical radio frequency spectrum analyzer based on a ~ 4cm long doped silica glass waveguide, with a bandwidth greater than 2.5 THz. We use this device to characterize the intensity power spectrum of ultrahigh repetition rate mode-locked lasers at repetition rates up to 400 GHz, and observe dynamic noise related behavior not observable with other techniques.

  11. Electrical spectrum & network analyzers a practical approach

    CERN Document Server

    Helfrick, Albert D

    1991-01-01

    This book presents fundamentals and the latest techniques of electrical spectrum analysis. It focuses on instruments and techniques used on spectrum and network analysis, rather than theory. The book covers the use of spectrum analyzers, tracking generators, and network analyzers. Filled with practical examples, the book presents techniques that are widely used in signal processing and communications applications, yet are difficult to find in most literature.Key Features* Presents numerous practical examples, including actual spectrum analyzer circuits* Instruction on how to us

  12. Performance evaluation of PL-11 platelet analyzer

    Institute of Scientific and Technical Information of China (English)

    张有涛

    2013-01-01

    Objective To evaluate and report the performance of PL-11 platelet analyzer. Methods Intravenous blood sam-ples anticoagulated with EDTA-K2 and sodium citrate were tested by the PL-11 platelet analyzer to evaluate the intra-assay and interassay coefficient of variation(CV),

  13. Program Analyzes Performance Of A Wind Tunnel

    Science.gov (United States)

    Viterna, L. A.

    1994-01-01

    WT computer program developed to calculate rotor power required by, and output thrust produced by, fan in closed-loop wind tunnel. Uses blade-element theory to calculate aerodynamic forces along each blade of fan. Written in APL2.

  14. The war in Bosnia, 1992-1995: analyzing military asymmetries and failures

    OpenAIRE

    Anghel, Gheorghe.

    2000-01-01

    This thesis analyzes the three key failures by the leading external powers in their efforts in 1992-1995 to manage the crisis in Bosnia and impose a settlement. Except for Russia, these leading powers were the so-called NATO quad: Britain, France, Germany, and the United States. when these powers initially intervened, they failed to comprehend the origins and dynamics of the Yugoslav crisis. These powers successively failed to prevent the outbreak of the fighting, then to properly contain it,...

  15. Nuclear power and public perceptions

    International Nuclear Information System (INIS)

    This text presents and analyzes a survey dealing with public opinion about nuclear power. The author suggests ways to improve communication and information in order to lead people to have a better opinion concerning nuclear power. (TEC)

  16. Multidimensional analyzer based on the MACAMAC system

    International Nuclear Information System (INIS)

    General information about multidimensional analyzer based on the MACAMAC system is given. The analyzer includes the 1521 microprocessor controller and the 1522 memory modules of the ''Borer'' firm (Switzerland), CAMAC modules: ADCs, coincidence organization module, display driver, paper tape input and output modules. The Videoton-34O serves as a terminal, and for data visualization the RG-96 display device is used. The analyzer software includes: a monitor, data acquisition programs, display program and users' programs. The monitor organizes user-system dialogue by means of terminal keyboard

  17. Systems Analyze Water Quality in Real Time

    Science.gov (United States)

    2010-01-01

    A water analyzer developed under Small Business Innovation Research (SBIR) contracts with Kennedy Space Center now monitors treatment processes at water and wastewater facilities around the world. Originally designed to provide real-time detection of nutrient levels in hydroponic solutions for growing plants in space, the ChemScan analyzer, produced by ASA Analytics Inc., of Waukesha, Wisconsin, utilizes spectrometry and chemometric algorithms to automatically analyze multiple parameters in the water treatment process with little need for maintenance, calibration, or operator intervention. The company has experienced a compound annual growth rate of 40 percent over its 15-year history as a direct result of the technology's success.

  18. Low Gravity Drug Stability Analyzer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall goal of this proposed program (through Phase III) is to build a space-worthy Drug Stability Analyzer that can determine the extent of drug degradation....

  19. Low Gravity Drug Stability Analyzer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of this proposed program through Phase III is to build a space-worthy Drug Stability Analyzer that can determine the extent of drug degradation. It will be...

  20. On-Demand Urine Analyzer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall goal of this program (through Phase III) is to develop an analyzer that can be integrated into International Space Station (ISS) toilets to measure key...

  1. QUBIT DATA STRUCTURES FOR ANALYZING COMPUTING SYSTEMS

    Directory of Open Access Journals (Sweden)

    Vladimir Hahanov

    2014-11-01

    Full Text Available Qubit models and methods for improving the performance of software and hardware for analyzing digital devices through increasing the dimension of the data structures and memory are proposed. The basic concepts, terminology and definitions necessary for the implementation of quantum computing when analyzing virtual computers are introduced. The investigation results concerning design and modeling computer systems in a cyberspace based on the use of two-component structure are presented.

  2. Analyzing Log Files using Data-Mining

    OpenAIRE

    Marius Mihut

    2008-01-01

    Information systems (i.e. servers, applications and communication devices) create a large amount of monitoring data that are saved as log files. For analyzing them, a data-mining approach is helpful. This article presents the steps which are necessary for creating an ‘analyzing instrument’, based on an open source software called Waikato Environment for Knowledge Analysis (Weka) [1]. For exemplification, a system log file created by a Windows-based operating system, is used as input file.

  3. The Information Flow Analyzing Based on CPC

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhang; LI Hui

    2005-01-01

    The information flow chart within product life cycle is given out based on collaborative production commerce (CPC) thoughts. In this chart, the separated information systems are integrated by means of enterprise knowledge assets that are promoted by CPC from production knowledge. The information flow in R&D process is analyzed in the environment of virtual R&D group and distributed PDM. In addition, the information flow throughout the manufacturing and marketing process is analyzed in CPC environment.

  4. Network analysis using organizational risk analyzer

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The tool system of the organizational risk analyzer (ORA) to study the network of East Turkistan terrorists is selected. The model of the relationships among its personnel, knowledge, resources and task entities is represented by the meta-matrix in ORA, with which to analyze the risks and vulnerabilities of organizational structure quantitatively, and obtain the last vulnerabilities and risks of the organization. Case study in this system shows that it should be a shortcut to destroy effectively the network...

  5. Shielded electron microprobe analyzer for plutonium fuel

    International Nuclear Information System (INIS)

    Design, construction and performance test of a shielded electron microprobe analyzer for plutonium fuel are described. In the analyzer, the following modifications were made to Shimadzu ASM-SX (analyzer): (1) a shield of tungsten alloy is incorporated between the sample and the X-ray detector to examine highly radioactive fuel, (2) a magnetic shield against β-rays from the fuel is fitted to the electron detector, (3) a small sample-loading glove box is installed to transfer plutonium fuel safely to the analyzer, (4) a glove box containing a sample-surface treatment apparatus and a balance is connected to the sample-loading glove box, (5) for maintenance and repair of the analyzer by means of closed method, about thirty modifications are made. The performance test with nonradioactive materials showed that despite the above modifications, abilities of the original analyzer are all retained. And furthermore, the simulation test for irradiated fuel with 226Ra of dose rate 40 mR/hr at 30 cm showed that the X-ray peaks to noise ratios are unchanged by using a pulse height selector of the X-ray detector. (author)

  6. Nuclear power economics

    International Nuclear Information System (INIS)

    The economical comparison of nuclear power plants with coal-fired plants in some countries or areas are analyzed. It is not difficult to show that nuclear power will have a significant and expanding role to play in providing economic electricity in the coming decades. (Liu)

  7. Power Curve Measurements

    DEFF Research Database (Denmark)

    Yordanova, Ginka; Vesth, Allan

    The report describes power curve measurements carried out on a given wind turbine. The measurements are carried out in accordance to Ref. [1]. A site calibration has been carried out; see Ref. [2], and the measured flow correction factors for different wind directions are used in the present...... analyze of power performance of the turbine....

  8. Power Curve Measurements, FGW

    DEFF Research Database (Denmark)

    Vesth, Allan; Yordanova, Ginka

    The report describes power curve measurements carried out on a given wind turbine. The measurements are carried out in accordance to Ref. [1]. A site calibration has been carried out; see Ref. [2], and the measured flow correction factors for different wind directions are used in the present...... analyze of power performance of the turbine....

  9. FST Based Morphological Analyzer for Hindi Language

    Directory of Open Access Journals (Sweden)

    Deepak Kumar

    2012-07-01

    Full Text Available Hindi being a highly inflectional language, FST (Finite State Transducer based approach is most efficient for developing a morphological analyzer for this language. The work presented in this paper uses the SFST (Stuttgart Finite State Transducer tool for generating the FST. A lexicon of root words is created. Rules are then added for generating inflectional and derivational words from these root words. The Morph Analyzer developed was used in a Part Of Speech (POS Tagger based on Stanford POS Tagger. The system was first trained using a manually tagged corpus and MAXENT (Maximum Entropy approach of Stanford POS tagger was then used for tagging input sentences. The morphological analyzer gives approximately 97% correct results. POS tagger gives an accuracy of approximately 87% for the sentences that have the words known to the trained model file, and 80% accuracy for the sentences that have the words unknown to the trained model file.

  10. Power Module

    OpenAIRE

    Gang Fang

    2009-01-01

    Abstract: In this paper, we discuss the upgrade problem of module, and introduce the concepts of the power module, regular power module and uniform power module. We give some results of them. Key words: power group; power module; regular power module; uniform power module

  11. Applications of low level scintillation analyzers

    International Nuclear Information System (INIS)

    The use of a liquid scintillation counter to quantitate radio-activity for low level applications is explored. The applications include 14C dating, hydrology, geology studies, food adulteration studies, environmental monitoring, biomedical, and assessing radio-isotopes in nuclear power plants. (author). 1 fig

  12. Detecting influenza outbreaks by analyzing Twitter messages

    CERN Document Server

    Culotta, Aron

    2010-01-01

    We analyze over 500 million Twitter messages from an eight month period and find that tracking a small number of flu-related keywords allows us to forecast future influenza rates with high accuracy, obtaining a 95% correlation with national health statistics. We then analyze the robustness of this approach to spurious keyword matches, and we propose a document classification component to filter these misleading messages. We find that this document classifier can reduce error rates by over half in simulated false alarm experiments, though more research is needed to develop methods that are robust in cases of extremely high noise.

  13. Analyzing Log Files using Data-Mining

    Directory of Open Access Journals (Sweden)

    Marius Mihut

    2008-01-01

    Full Text Available Information systems (i.e. servers, applications and communication devices create a large amount of monitoring data that are saved as log files. For analyzing them, a data-mining approach is helpful. This article presents the steps which are necessary for creating an ‘analyzing instrument’, based on an open source software called Waikato Environment for Knowledge Analysis (Weka [1]. For exemplification, a system log file created by a Windows-based operating system, is used as input file.

  14. Progresses in analyzing 26Al with SMCAMS

    International Nuclear Information System (INIS)

    Shanghai Mini-Cyclotron based Accelerator Mass Spectrometer (SMCAMS) was especially designed for analyzing 14C. In order to accelerate and analyze 26Al the accelerated orbit and beam optics in injection system were calculated and harmonic number and acceleration turns was optimized. Preliminary experiment was carried out. In which a beam current of 1.15 x 10-9A for 27Al- and 0.038 CPS background for 26Al were measured. The limited sensitivity of 26Al/27Al is 5.25 x 10-12. (authors)

  15. A Novel Architecture For Multichannel Analyzer

    International Nuclear Information System (INIS)

    A novel digital approach to real-time, high-throughput, low-cost Multichannel Analyzer (MCA) for radiation spectroscopy is being presented. The MCA input is a shaped nuclear pulse sampled at a high rate, using an Analog-to-Digital Converter (ADC) chip. The digital samples are analyzed by a state-of-the-art Field Programmable Gate Away (FPGA). A customized algorithm is utilized to estimate the peak of the pulse, to reject pile-up and to eliminate processing dead time. The valid pulses estimated peaks are transferred to a micro controller system that creates the histogram and controls the Human Machine Interface (HMI)

  16. Development of the combustion engineering reactivity analyzer system

    International Nuclear Information System (INIS)

    The C-E Reactivity Analyzer (CERA trademark) is an interactive, personal computer based, low power physics data collection and reduction system developed to support pressurized water reactor test programs. The CERA system consists of hardware and software to acquire, digitize, and analyze data for the isothermal temperature coefficient (ITC) and control rod bank worth measurements. The CERA system uses expert-level data analysis algorithms to assist the plant reactor engineer in determining measured values of the ITC and rod bank worths. Statistical, qualitative, and quantitative evaluations of test data fidelity are also provided. The CERA data analysis methodology is a significant advance in speed, accuracy, and test anomaly identification over the standard method of manual data reduction using strip charts and hand-collected data

  17. BWR plant analyzer development at BNL [Brookhaven National Laboratory

    International Nuclear Information System (INIS)

    An engineering plant analyzer has been developed at BNL for realistically and accurately simulating transients and severe abnormal events in BWR power plants. Simulations are being carried out routinely with high fidelity, high simulation speed, at low cost and with unsurpassed user convenience. The BNL Plant Analyzer is the only operating facility which (a) simulates more than two orders-of-magnitude faster than the CDC-7600 mainframe computer, (b) is accessible and fully operational in on-line interactive mode, remotely from anywhere in the US, from Europe or the Far East (Korea), via widely available IBM-PC compatible personal computers, standard modems and telephone lines, (c) simulates both slow and rapid transients seven times faster than real-time in direct access, and four times faster in remote access modes, (d) achieves high simulation speed without compromising fidelity, and (e) is available to remote access users at the low cost of $160 per hour

  18. The wireshark field guide analyzing and troubleshooting network traffic

    CERN Document Server

    Shimonski, Robert

    2013-01-01

    The Wireshark Field Guide provides hackers, pen testers, and network administrators with practical guidance on capturing and interactively browsing computer network traffic. Wireshark is the world's foremost network protocol analyzer, with a rich feature set that includes deep inspection of hundreds of protocols, live capture, offline analysis and many other features. The Wireshark Field Guide covers the installation, configuration and use of this powerful multi-platform tool. The book give readers the hands-on skills to be more productive with Wireshark as they drill

  19. Consideration Regarding Diagnosis Analyze of Corporate Management

    Directory of Open Access Journals (Sweden)

    Mihaela Ciopi OPREA

    2009-01-01

    Full Text Available Diagnosis management aims to identify critical situations and positive aspectsof corporate management. An effective diagnosis made by a team with thestatus of independence from the organization’s management is for managers auseful feedback necessary to improve performance. The work presented focuseson the methodology to achieve effective diagnosis, considering multitudecriteria and variables to be analyzed.

  20. Portable peltier-cooled X RF analyzer

    International Nuclear Information System (INIS)

    Full text: Recent development of semiconductor detectors has made it possible to design portable battery operated XRF-analyzers. Energy resolution and good peak to background ratio are close to liquid nitrogen cooled detector values. Application examples are given and a comparison of the new device between old ones is made. (author)

  1. Graphic method for analyzing common path interferometers

    DEFF Research Database (Denmark)

    Glückstad, J.

    1998-01-01

    Common path interferometers are widely used for visualizing phase disturbances and fluid flows. They are attractive because of the inherent simplicity and robustness in the setup. A graphic method will be presented for analyzing and optimizing filter parameters in common path interferometers....

  2. How to Analyze Company Using Social Network?

    Science.gov (United States)

    Palus, Sebastian; Bródka, Piotr; Kazienko, Przemysław

    Every single company or institution wants to utilize its resources in the most efficient way. In order to do so they have to be have good structure. The new way to analyze company structure by utilizing existing within company natural social network and example of its usage on Enron company are presented in this paper.

  3. Analyzing Vessel Behavior Using Process Mining

    NARCIS (Netherlands)

    Maggi, F.M.; Mooij, A.J.; Aalst, W.M.P. van der

    2013-01-01

    In the maritime domain, electronic sensors such as AIS receivers and radars collect large amounts of data about the vessels in a certain geographical area. We investigate the use of process mining techniques for analyzing the behavior of the vessels based on these data. In the context of maritime sa

  4. Miniature retarding grid ion energy analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, G.W.; Sawin, H.H.

    1992-12-01

    A retarding grid analyzer intended for use as a high-density ({approximately}10{sup 12}/cc) plasma diagnostic has been designed, built and tested. The analyzer`s external dimensions are 0.125 inch x0.125 inch x0.050 inch which are smaller than macroscopic plasma scale lengths, thus allowing it to be stalk mounted and moved throughout the plasma. The grids are 2000 line/inch nickel mesh so that the linear dimension of grid open area is less than the debye length for plasmas with 10 eV electrons and 10{sup 12}/cc densities. Successive grids are separated by 0.01 inch in order to avoid space charge effects between grids and thus allow unprecedented energy resolution. Also, because the linear dimension normal to the grid is small compared to the ion mean free path in high pressure (>100 mTorr) discharges, it can be used without the differential pumping required of larger GEA`s in such discharges. The analyzer has been tested on a plasma beam source (a modified ASTeX Compact ECR source) and on an ASTeX S1500ECR source, and has been used as an edge diagnostic on the VERSATOR tokamak at M.I.T. Ion energy distribution functions as narrow as 5 eV have been measured.

  5. 40 CFR 92.109 - Analyzer specifications.

    Science.gov (United States)

    2010-07-01

    ... consistent with the general requirements of 40 CFR part 1065, subpart I, for sampling and analysis of... (CONTINUED) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.109... shall be at least 60 percent of full-scale chart deflection. For NOX analyzers using a water trap,...

  6. Modeling and analyzing architectural change with Alloy

    DEFF Research Database (Denmark)

    Hansen, Klaus Marius; Ingstrup, Mads

    2010-01-01

    to the uptake of reconfiguration techniques in industry. Using the Alloy language and associated tool, we propose a practical way to formally model and analyze runtime architectural change expressed as architectural scripts. Our evaluation shows the performance to be acceptable; our experience that...... the modelling language is convenient and expressive, and that our model accurately repesents the implementation it is used to reason about....

  7. Quantum Key Distribution with Screening and Analyzing

    CERN Document Server

    Kye, W H

    2006-01-01

    We propose a quantum key distribution scheme by using screening angles and analyzing detectors which enable to notice the presence of Eve who eavesdrops the quantum channel. We show the security of the proposed quantum key distribution against impersonation, photon number splitting, Trojan Horse, and composite attacks.

  8. Quantum Key Distribution with Screening and Analyzing

    OpenAIRE

    Kye, Won-Ho

    2006-01-01

    We propose a quantum key distribution scheme by using screening angles and analyzing detectors which enable to notice the presence of Eve who eavesdrops the quantum channel, as the revised protocol of the recent quantum key distribution [Phys. Rev. Lett. 95, 040501 (2005)]. We discuss the security of the proposed quantum key distribution against various attacks including impersonation attack and Trojan Horse attack.

  9. Analyzing computer system performance with Perl

    CERN Document Server

    Gunther, Neil J

    2011-01-01

    This expanded second edition of Analyzing Computer System Performance with Perl::PDQ, builds on the success of the first edition. It contains new chapters on queues, tools and virtualization, and new Perl listing format to aid readability of PDQ models.

  10. LINUX kernel analyzing and device driver design

    International Nuclear Information System (INIS)

    With the development of GNU software, more and more people try to apply Linux in Data Acquisition and Control System. The core techniques of kernel are analyzed and the key methods are introduced for designing LINUX Device Driver of PCI character device based on authors' realized Data Acquisition and Control System

  11. PROARTIS: Probabilistically Analyzable Real-Time System

    OpenAIRE

    Cazorla F.J.; Ones E.Q.; Vardanega T.; Cucu L.; Triquet B.; Bernat G.; Berger E.; Abella J.; Wartel F.; Houston M.

    2013-01-01

    Static timing analysis is the state-of-the-art practice of ascertaining the timing behavior of current-generation real-time embedded systems. The adoption of more complex hardware to respond to the increasing demand for computing power in next-generation systems exacerbates some of the limitations of static timing analysis. In particular, the effort of acquiring (1) detailed information on the hardware to develop an accurate model of its execution latency as well as (2) knowledge of the timin...

  12. Methodology for analyzing risk at nuclear facilities

    International Nuclear Information System (INIS)

    Highlights: • A new methodology for evaluating the risk at nuclear facilities was developed. • Five measures reflecting all factors that should be concerned to assess risk were developed. • The attributes on NMAC and nuclear security culture are included as attributes for analyzing. • The newly developed methodology can be used to evaluate risk of both existing facility and future nuclear system. - Abstract: A methodology for evaluating risks at nuclear facilities is developed in this work. A series of measures is drawn from the analysis of factors that determine risks. Five measures are created to evaluate risks at nuclear facilities. These include the legal and institutional framework, material control, physical protection system effectiveness, human resources, and consequences. Evaluation attributes are developed for each measure and specific values are given in order to calculate the risk value quantitatively. Questionnaires are drawn up on whether or not a state has properly established a legal and regulatory framework (based on international standards). These questionnaires can be a useful measure for comparing the status of the physical protection regime between two countries. Analyzing an insider threat is not an easy task and no methodology has been developed for this purpose. In this study, attributes that could quantitatively evaluate an insider threat, in the case of an unauthorized removal of nuclear materials, are developed by adopting the Nuclear Material Accounting & Control (NMAC) system. The effectiveness of a physical protection system, P(E), could be analyzed by calculating the probability of interruption, P(I), and the probability of neutralization, P(N). In this study, the Tool for Evaluating Security System (TESS) code developed by KINAC is used to calculate P(I) and P(N). Consequence is an important measure used to analyze risks at nuclear facilities. This measure comprises radiological, economic, and social damage. Social and

  13. Use of the Humphrey Lens Analyzer for off-axis measurements of spectacle lenses.

    Science.gov (United States)

    Atchison, D A; Kris, M; Sheedy, J E; Bailey, I L

    1991-04-01

    Automated focimeters can be used to make quick, precise measurements of off-axis power and prismatic effects corresponding to an eye rotating behind a spectacle lens. An automated focimeter, the Humphrey Lens Analyzer, was assessed in this regard. The Humphrey Lens Analyzer can be used to give a valid measure of off-axis power of lenses with low power, but not of lenses with moderate to higher power (greater than 3 D). For 3 D spherical lenses discrepancies of the order of 0.1 D occur at 30 degrees rotation, and 6 D spheres give discrepancies of 0.5 D at the same rotation. Small discrepancies were found for measurements of prism. The Humphrey Lens Analyzer was also used in a mode where the lens being tested is rotated about the center of curvature of its back surface. This is the mode often used to assess aberrations and prism of progressive-addition lenses. In this mode, the instrument provides reasonable accuracy in estimating off-axis power corresponding to eye rotation for lenses with low power, but not for lenses with moderate to higher power (greater than 3 D). However, it provides accurate values of the variation in off-axis surface power for low powered lenses with aspheric front surfaces. There were considerable systematic errors associated with the measurement of prism. A simple raytracing method was developed to predict the results of measurements with the Humphrey Lens Analyzer. Predictions of off-axis power were good when lenses were rotated about a position corresponding to the center-of-rotation of an eye, but were poorer when lenses were rotated about the center of curvature of their back surfaces. Predictions of primatic efforts were good in both situations. A method by which the Humphrey Lens Analyzer should provide an accurate measurement of off-axis powers corresponding to eye rotation behind a spectacle lens is described, but has not been tested. PMID:2052286

  14. An improved prism energy analyzer for neutrons

    International Nuclear Information System (INIS)

    The effects of two improvements of an existing neutron energy analyzer consisting of stacked silicon prism rows are presented. First we tested the effect of coating the back of the prism rows with an absorbing layer to suppress neutron scattering by total reflection and by refraction at small angles. Experiments at HZB showed that this works perfectly. Second the prism rows were bent to shift the transmitted wavelength band to larger wavelengths. At HZB we showed that bending increased the transmission of neutrons with a wavelength of 4.9 Å. Experiments with a white beam at the EROS reflectometer at LLB showed that bending of the energy analyzing device to a radius of 7.9 m allows to shift the transmitted wavelength band from 0 to 9 Å to 2 to 16 Å

  15. An improved prism energy analyzer for neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, J., E-mail: jennifer.schulz@helmholtz-berlin.de [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Ott, F. [Laboratoire Leon Brillouin, Bât 563 CEA Saclay, 91191 Gif sur Yvette Cedex (France); Krist, Th. [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner-Platz 1, 14109 Berlin (Germany)

    2014-04-21

    The effects of two improvements of an existing neutron energy analyzer consisting of stacked silicon prism rows are presented. First we tested the effect of coating the back of the prism rows with an absorbing layer to suppress neutron scattering by total reflection and by refraction at small angles. Experiments at HZB showed that this works perfectly. Second the prism rows were bent to shift the transmitted wavelength band to larger wavelengths. At HZB we showed that bending increased the transmission of neutrons with a wavelength of 4.9 Å. Experiments with a white beam at the EROS reflectometer at LLB showed that bending of the energy analyzing device to a radius of 7.9 m allows to shift the transmitted wavelength band from 0 to 9 Å to 2 to 16 Å.

  16. Information Theory for Analyzing Neural Networks

    OpenAIRE

    Sørngård, Bård

    2014-01-01

    The goal of this thesis was to investigate how information theory could be used to analyze artificial neural networks. For this purpose, two problems, a classification problem and a controller problem were considered. The classification problem was solved with a feedforward neural network trained with backpropagation, the controller problem was solved with a continuous-time recurrent neural network optimized with evolution.Results from the classification problem shows that mutual information ...

  17. Firms’ Innovation Strategies Analyzed and Explained

    OpenAIRE

    Tavassoli, Sam; Karlsson, Charlie

    2015-01-01

    This paper analyzes various innovation strategies of firms. Using five waves of the Community Innovation Survey in Sweden, we have traced the innovative behavior of firms over a ten-year period, i.e. between 2002 and 2012. We distinguish between sixteen innovation strategies, which compose of Schumpeterian four types of innovations (process, product, marketing, and organizational) plus various combinations of these four types. First, we find that firms are not homogenous in choosing innovatio...

  18. The analyzing of Dove marketing strategy

    Institute of Scientific and Technical Information of China (English)

    Guo; Yaohui

    2015-01-01

    <正>1.Introduction In this report,I try to analyze the related information about DOVE chocolate.Firstly,I would like to introduce this product.Dove chocolate is one of a series of products launched by the world’s largest pet food and snack food manufacturers,U.S.multinational food company Mars(Mars).Entered China in 1989,It becomes China’s leading brand of chocolate in

  19. LEGAL-EASE:Analyzing Chinese Financial Statements

    Institute of Scientific and Technical Information of China (English)

    EDWARD; MA

    2008-01-01

    In this article,we will focus on under- standing and analyzing the typical accounts of Chinese financial statements,including the balance sheet and income statement. Accounts are generally incorrectly prepared. This can be due to several factors,incom- petence,as well as more serious cases of deliberate attempts to deceive.Regardless, accounts can be understood and errors or specific acts of misrepresentation uncovered. We will conduct some simple analysis to demonstrate how these can be spotted.

  20. Organization theory. Analyzing health care organizations.

    Science.gov (United States)

    Cors, W K

    1997-02-01

    Organization theory (OT) is a tool that can be applied to analyze and understand health care organizations. Transaction cost theory is used to explain, in a unifying fashion, the myriad changes being undertaken by different groups of constituencies in health care. Agency theory is applied to aligning economic incentives needed to ensure Integrated Delivery System (IDS) success. By using tools such as OT, a clearer understanding of organizational changes is possible. PMID:10164970

  1. SPAM: Signal Processing to Analyze Malware

    OpenAIRE

    Nataraj, Lakshmanan; Manjunath, B.S.

    2016-01-01

    In this article, we explored orthogonal methods to analyze malware motivated by signal and image processing. Malware samples are represented as images or signals. Image and signal-based features are extracted to characterize malware. Our extensive experiments demonstrate the efficacy of our methods on malware classification and retrieval. We believe that our techniques will open the scope of signal-and image-based methods to broader fields in computer security.

  2. Analyzing the robustness of telecommunication networks

    OpenAIRE

    Eller, Karol Schaeffer

    1992-01-01

    This project report defines network robustness and discusses capability indicators that could be used to analyze network robustness. Growing dependence on telecommunication networks and recent network outages have focused attention on network robustness. The National Communications System (NCS), a confederation of 23 Federal departments and agencies, has been concerned with network robustness since its formation in 1963. The NCS is developing and implementing systems a...

  3. Coordinating, Scheduling, Processing and Analyzing IYA09

    Science.gov (United States)

    Gipson, John; Behrend, Dirk; Gordon, David; Himwich, Ed; MacMillan, Dan; Titus, Mike; Corey, Brian

    2010-01-01

    The IVS scheduled a special astrometric VLBI session for the International Year of Astronomy 2009 (IYA09) commemorating 400 years of optical astronomy and 40 years of VLBI. The IYA09 session is the most ambitious geodetic session to date in terms of network size, number of sources, and number of observations. We describe the process of designing, coordinating, scheduling, pre-session station checkout, correlating, and analyzing this session.

  4. SACO: Static analyzer for concurrent objects

    OpenAIRE

    Albert Albiol, Elvira; Arenas Sánchez, Purificación; Flores Montoya, A.; Genaim, Samir; Gómez-Zamalloa Gil, Miguel; Martín Martín, Enrique; Puebla, G.; Román Díez, Guillermo

    2014-01-01

    We present the main concepts, usage and implementation of SACO, a static analyzer for concurrent objects. Interestingly, SACO is able to infer both liveness(namely termination and resource boundedness) and safety properties (namely deadlock freedom) of programs based on concurrent objects. The system integrates auxiliary analyses such as points-to and may-happen-in-parallel, which are essential for increasing the accuracy of the aforementioned more complex properties. SACO provides accurate ...

  5. ANANAS - A Framework For Analyzing Android Applications

    OpenAIRE

    Eder, Thomas; Rodler, Michael; Vymazal, Dieter; Zeilinger, Markus

    2013-01-01

    Android is an open software platform for mobile devices with a large market share in the smartphone sector. The openness of the system as well as its wide adoption lead to an increasing amount of malware developed for this platform. ANANAS is an expandable and modular framework for analyzing Android applications. It takes care of common needs for dynamic malware analysis and provides an interface for the development of plugins. Adaptability and expandability have been main design goals during...

  6. Measuring and analyzing child labor: methodological issues

    OpenAIRE

    Grimsrud, Bjorne

    2002-01-01

    Current statistics on child labor are generally based on economically active children. This paper will argue that these figures are not a workable proxy for data on child labor, generating numbers of child laborers, and their gender composition that do not represent the group described by the international definition of child labor. This raises the question of reliable alternatives ways of measuring children's activities, with the aim of analyzing the incidence of child labor. The paper addre...

  7. Measuring and analyzing child labor : methodological issues

    OpenAIRE

    Grimsrud, Bjorne

    2001-01-01

    The paper argues that the current statistics on child labor (generally based on economically active children), are not a workable proxy for data on child labor, generating numbers of child laborers, and their gender composition, that do not represent the groups described by the international definition of child labor. This raises the question of reliable alternative ways of measuring children's activities, with the aim of analyzing the incidence of child labor. The paper addresses this, and p...

  8. Thermo Scientific Sulfur Dioxide Analyzer Instrument Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Springston, S. R. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-03-01

    The Sulfur Dioxide Analyzer measures sulfur dioxide based on absorbance of UV light at one wavelength by SO2 molecules which then decay to a lower energy state by emitting UV light at a longer wavelength. Specifically, SO2 + hυ1 →SO2 *→SO2 + hυ2 The emitted light is proportional to the concentration of SO2 in the optical cell. External communication with the analyzer is available through an Ethernet port configured through the instrument network of the AOS systems. The Model 43i-TLE is part of the i-series of Thermo Scientific instruments. The i-series instruments are designed to interface with external computers through the proprietary Thermo Scientific iPort Software. However, this software is somewhat cumbersome and inflexible. BNL has written an interface program in National Instruments LabView that both controls the Model 43i-TLE Analyzer AND queries the unit for all measurement and housekeeping data. The LabView vi (the software program written by BNL) ingests all raw data from the instrument and outputs raw data files in a uniform data format similar to other instruments in the AOS and described more fully in Section 6.0 below.

  9. Aliasing Errours in Parallel Signature Analyzers

    Institute of Scientific and Technical Information of China (English)

    闵应骅; YashwantK.Malaiya

    1990-01-01

    A Linear Feedback Shift Register(LFSR)can be used to compress test response data as a Signature Analyzer(SA).Parallel Signature Analyzers(PSAs)implemented as multiple input LFSRs are faster and require less hardware overhead than Serial Signature Analyzers(SSAs) for compacting test response data for Built-In Self-Test(BIST)in IC of boare-testing environments.However,the SAs are prone to aliasing errors because of some specific types of error patterns.An alias is a faulty output signature that is identical to the fault-free signature.A penetrating analysis of detecting capability of SAs depends strongly on mathematical manipulations,instead of being aware of some special cases of examples.In addition,the analysis should not be restricted to a particular structure of LFSR,but be appropriate for various structures of LFSRs.This paper presents necessary and sufficient conditions for aliasing errors based on a complete mathematical description of various types of SAs.An LFSR reconfiguration scheme is suggested which will prevent any aliasing double errors.Such a prevention cannot be obtained by any extension of an LFSR.

  10. Method of stabilizing single channel analyzers

    International Nuclear Information System (INIS)

    A method and the apparatus to reduce the drift of single channel analyzers are described. Essentially, this invention employs a time-sharing or multiplexing technique to insure that the outputs from two single channel analyzers (SCAS) maintain the same count ratio regardless of variations in the threshold voltage source or voltage changes, the multiplexing technique is accomplished when a flip flop, actuated by a clock, changes state to switch the output from the individual SCAS before these outputs are sent to a ratio counting scalar. In the particular system embodiment disclosed that illustrates this invention, the sulfur content of coal is determined by subjecting the coal to radiation from a neutron producing source. A photomultiplier and detector system equates the transmitted gamma radiation to an analog voltage signal and sends the same signal after amplification, to a SCA system that contains the invention. Therein, at least two single channel analyzers scan the analog signal over different parts of a spectral region. The two outputs may then be sent to a digital multiplexer so that the output from the multiplexer contains counts falling within two distinct segments of the region. By dividing the counts from the multiplexer by each other, the percentage of sulfur within the coal sample under observation may be determined. (U.S.)

  11. Blood culture cross contamination associated with a radiometric analyzer

    International Nuclear Information System (INIS)

    During a 9-day period in August 1980 in a New Jersey hospital, three pairs of consecutively numbered blood cultures from different patients were identified as positive for the same organism, for each pair, both cultures were positive in the same atmosphere, both organisms had the same sensitivities, and the second of each pair grew at least 2 days after the first and was the only positive blood culture obtained from the patient. When the hospital laboratory discontinued use of its radiometric culture analyzer for 15 days, no more consecutive pairs of positive cultures occurred. Subsequent use of the machine for 9 days with a new power unit but the original circuit boards resulted in one more similar consecutive pair (Staphylococcus epidermidis). After replacement of the entire power unit, there were no further such pairs. Examination of the machine by the manufacturer revealed a defective circuit board which resulted in inadequate needle sterilization. Laboratories which utilize radiometric analyzers should be aware of the potential for cross contamination. Recognition of such events requires alert microbiologists and infection control practitioners and a record system in the bacteriology laboratory designed to identify such clusters

  12. QA practice for online analyzers in water steam cycles

    International Nuclear Information System (INIS)

    The liberalization of power markets throughout the world has resulted in more and more power stations being operated in cycling mode, with frequent load changes and multiple daily start-up and shut-down cycles. This more flexible operation also calls for better automation and poses new challenges to water chemistry in water steam cycles, to avoid subsequent damage to vital plant components such as turbines, boilers or condensers. But automation for the most important chemistry control tool, the sampling and online analyzer system, is only possible if chemists can rely on their online analysis equipment. Proof of plausibility as well as reliability and availability of online analysis results becomes a major focus. While SOP and standard QA procedures for laboratory equipment are well established and daily practice, such measures are widely neglected for online process analyzers. This paper is aiming to establish a roadmap for the implementation of SOP and QA/QC procedures for online instruments in water steam cycles, leading to reliable chemical information that is trustworthy for process automation and chemistry control in water steam cycles. (author)

  13. Capturing and analyzing wheelchair maneuvering patterns with mobile cloud computing.

    Science.gov (United States)

    Fu, Jicheng; Hao, Wei; White, Travis; Yan, Yuqing; Jones, Maria; Jan, Yih-Kuen

    2013-01-01

    Power wheelchairs have been widely used to provide independent mobility to people with disabilities. Despite great advancements in power wheelchair technology, research shows that wheelchair related accidents occur frequently. To ensure safe maneuverability, capturing wheelchair maneuvering patterns is fundamental to enable other research, such as safe robotic assistance for wheelchair users. In this study, we propose to record, store, and analyze wheelchair maneuvering data by means of mobile cloud computing. Specifically, the accelerometer and gyroscope sensors in smart phones are used to record wheelchair maneuvering data in real-time. Then, the recorded data are periodically transmitted to the cloud for storage and analysis. The analyzed results are then made available to various types of users, such as mobile phone users, traditional desktop users, etc. The combination of mobile computing and cloud computing leverages the advantages of both techniques and extends the smart phone's capabilities of computing and data storage via the Internet. We performed a case study to implement the mobile cloud computing framework using Android smart phones and Google App Engine, a popular cloud computing platform. Experimental results demonstrated the feasibility of the proposed mobile cloud computing framework. PMID:24110214

  14. Development of turbine cycle performance analyzer using intelligent data mining

    International Nuclear Information System (INIS)

    In recent year, the performance enhancement of turbine cycle in nuclear power plants is being highlighted because of worldwide deregulation environment. Especially the first target of operating plants became the reduction of operating cost to compete other power plants. It is known that overhaul interval is closely related to operating cost Author identified that the rapid and reliable performance tests, analysis, and diagnosis play an important role in the control of overhaul interval through field investigation. First the technical road map was proposed to clearly set up the objectives. The controversial issues were summarized into data gathering, analysis tool, and diagnosis method. Author proposed the integrated solution on the basis of intelligent data mining techniques. For the reliable data gathering, the state analyzer composed of statistical regression, wavelet analysis, and neural network was developed. The role of the state analyzer is to estimate unmeasured data and to increase the reliability of the collected data. For the advanced performance analysis, performance analysis toolbox was developed. The purpose of this tool makes analysis process easier and more accurate by providing three novel heat balance diagrams. This tool includes the state analyzer and turbine cycle simulation code. In diagnosis module, the probabilistic technique based on Bayesian network model and the deterministic technique based on algebraical model are provided together. It compromises the uncertainty in diagnosis process and the pin-point capability. All the modules were validated by simulated data as well as actual test data, and some modules are used as industrial applications. We have a lot of thing to be improved in turbine cycle in order to increase plant availability. This study was accomplished to remind the concern about the importance of turbine cycle and to propose the solutions on the basis of academic as well as industrial needs

  15. A chemical analyzer for charged ultrafine particles

    Directory of Open Access Journals (Sweden)

    S. G. Gonser

    2013-04-01

    Full Text Available New particle formation is a frequent phenomenon in the atmosphere and of major significance for the earth's climate and human health. To date the mechanisms leading to the nucleation of particles as well as to aerosol growth are not completely understood. A lack of appropriate measurement equipment for online analysis of the chemical composition of freshly nucleated particles is one major limitation. We have developed a Chemical Analyzer for Charged Ultrafine Particles (CAChUP capable of analyzing particles with diameters below 30 nm. A bulk of size separated particles is collected electrostatically on a metal filament, resistively desorbed and consequently analyzed for its molecular composition in a time of flight mass spectrometer. We report of technical details as well as characterization experiments performed with the CAChUP. Our instrument was tested in the laboratory for its detection performance as well as for its collection and desorption capabilities. The manual application of known masses of camphene (C10H16 to the desorption filament resulted in a detection limit between 0.5 and 5 ng, and showed a linear response of the mass spectrometer. Flow tube experiments of 25 nm diameter secondary organic aerosol from ozonolysis of alpha-pinene also showed a linear relation between collection time and the mass spectrometer's signal intensity. The resulting mass spectra from the collection experiments are in good agreement with published work on particles generated by the ozonolysis of alpha-pinene. A sensitivity study shows that the current setup of CAChUP is ready for laboratory measurements and for the observation of new particle formation events in the field.

  16. A computer program for analyzing channel geometry

    Science.gov (United States)

    Regan, R.S.; Schaffranek, R.W.

    1985-01-01

    The Channel Geometry Analysis Program (CGAP) provides the capability to process, analyze, and format cross-sectional data for input to flow/transport simulation models or other computational programs. CGAP allows for a variety of cross-sectional data input formats through use of variable format specification. The program accepts data from various computer media and provides for modification of machine-stored parameter values. CGAP has been devised to provide a rapid and efficient means of computing and analyzing the physical properties of an open-channel reach defined by a sequence of cross sections. CGAP 's 16 options provide a wide range of methods by which to analyze and depict a channel reach and its individual cross-sectional properties. The primary function of the program is to compute the area, width, wetted perimeter, and hydraulic radius of cross sections at successive increments of water surface elevation (stage) from data that consist of coordinate pairs of cross-channel distances and land surface or channel bottom elevations. Longitudinal rates-of-change of cross-sectional properties are also computed, as are the mean properties of a channel reach. Output products include tabular lists of cross-sectional area, channel width, wetted perimeter, hydraulic radius, average depth, and cross-sectional symmetry computed as functions of stage; plots of cross sections; plots of cross-sectional area and (or) channel width as functions of stage; tabular lists of cross-sectional area and channel width computed as functions of stage for subdivisions of a cross section; plots of cross sections in isometric projection; and plots of cross-sectional area at a fixed stage as a function of longitudinal distance along an open-channel reach. A Command Procedure Language program and Job Control Language procedure exist to facilitate program execution on the U.S. Geological Survey Prime and Amdahl computer systems respectively. (Lantz-PTT)

  17. Dynamic simulation analyzes expanded refinery steam system

    Energy Technology Data Exchange (ETDEWEB)

    Gandhi, S.L.; Graham, J.; Duffield, M.A.; Cortes, R.M. [M.W. Kellogg Co., Houston, TX (United States)

    1995-11-01

    There is a rising demand for more-stable process operations with increasing facility modernization and automation. This requires steam system controls that provide effective and stable responses to operational disturbances. Today it is possible to use dynamic simulation analysis for designing steam systems. The main objectives were to: develop a high-fidelity dynamic simulation model of the steam system and its associated controls; develop dynamic system responses to major plant disturbances; and assist in designing new control strategies and modifying existing controls to minimize the impact of plant upsets on system performance. The steam system for this project included two power plant supplying steam and power and a steam pipe network comprising three levels of steam with stream flows to and from process units spread over several square kilometers. Whether the steam system and its controls would respond effectively to major operational upsets, such as boiler, steam turbogenerator or process gas compressor trips, or a steep increase in steam demand, can only be determined from evaluating dynamic responses to these incidents. The model consisted of about 5,000 equations, 1,000 parameters and data items, and was used for evaluating steam system responses to various operational upset scenarios. The responses were used to identify limitations of the as designed control system. The model also proved to be an effective tool for verifying adequacy of the proposed recommendations. These included modifications to control valve letdown stations, steam turbogenerator governor controls and the boiler master-pressure controller.

  18. Analyzing the Control Structure of PEPA

    DEFF Research Database (Denmark)

    Yang, Fan; Nielson, Hanne Riis

    The Performance Evaluation Process Algebra, PEPA, is introduced by Jane Hillston as a stochastic process algebra for modelling distributed systems and especially suitable for performance evaluation. We present a static analysis that very precisely approximates the control structure of processes...... to PEPA programs, the approximating result is very precise. Based on the analysis, we also develop algorithms for validating the deadlock property of PEPA programs. The techniques have been implemented in a tool which is able to analyze processes with a control structure that more than one thousand...

  19. Analyzing the Biology on the System Level

    Institute of Scientific and Technical Information of China (English)

    Wei Tong

    2004-01-01

    Although various genome projects have provided us enormous static sequence information, understanding of the sophisticated biology continues to require integrating the computational modeling, system analysis, technology development for experiments, and quantitative experiments all together to analyze the biology architecture on various levels, which is just the origin of systems biology subject. This review discusses the object, its characteristics, and research attentions in systems biology, and summarizes the analysis methods, experimental technologies, research developments, and so on in the four key fields of systems biology-systemic structures, dynamics, control methods, and design principles.

  20. Using SCR methods to analyze requirements documentation

    Science.gov (United States)

    Callahan, John; Morrison, Jeffery

    1995-01-01

    Software Cost Reduction (SCR) methods are being utilized to analyze and verify selected parts of NASA's EOS-DIS Core System (ECS) requirements documentation. SCR is being used as a spot-inspection tool. Through this formal and systematic approach of the SCR requirements methods, insights as to whether the requirements are internally inconsistent or incomplete as the scenarios of intended usage evolve in the OC (Operations Concept) documentation. Thus, by modelling the scenarios and requirements as mode charts using the SCR methods, we have been able to identify problems within and between the documents.

  1. Thermo Scientific Ozone Analyzer Instrument Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Springston, S. R. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-03-01

    The primary measurement output from the Thermo Scientific Ozone Analyzer is the concentration of the analyte (O3) reported at 1-s resolution in units of ppbv in ambient air. Note that because of internal pneumatic switching limitations the instrument only makes an independent measurement every 4 seconds. Thus, the same concentration number is repeated roughly 4 times at the uniform, monotonic 1-s time base used in the AOS systems. Accompanying instrument outputs include sample temperatures, flows, chamber pressure, lamp intensities and a multiplicity of housekeeping information. There is also a field for operator comments made at any time while data is being collected.

  2. The kpx, a program analyzer for parallelization

    International Nuclear Information System (INIS)

    The kpx is a program analyzer, developed as a common technological basis for promoting parallel processing. The kpx consists of three tools. The first is ktool, that shows how much execution time is spent in program segments. The second is ptool, that shows parallelization overhead on the Paragon system. The last is xtool, that shows parallelization overhead on the VPP system. The kpx, designed to work for any FORTRAN cord on any UNIX computer, is confirmed to work well after testing on Paragon, SP2, SR2201, VPP500, VPP300, Monte-4, SX-4 and T90. (author)

  3. Light-weight analyzer for odor recognition

    Energy Technology Data Exchange (ETDEWEB)

    Vass, Arpad A; Wise, Marcus B

    2014-05-20

    The invention provides a light weight analyzer, e.g., detector, capable of locating clandestine graves. The detector utilizes the very specific and unique chemicals identified in the database of human decompositional odor. This detector, based on specific chemical compounds found relevant to human decomposition, is the next step forward in clandestine grave detection and will take the guess-work out of current methods using canines and ground-penetrating radar, which have historically been unreliable. The detector is self contained, portable and built for field use. Both visual and auditory cues are provided to the operator.

  4. Analyzing Ever Growing Datasets in PHENIX

    International Nuclear Information System (INIS)

    After 10 years of running, the PHENIX experiment has by now accumulated more than 700 TB of reconstructed data which are directly used for analysis. Analyzing these amounts of data efficiently requires a coordinated approach. Beginning in 2005 we started to develop a system for the RHIC Atlas Computing Facility (RACF) which allows the efficient analysis of these large data sets. The Analysis Taxi is now the tool which allows any collaborator to process any data set taken since 2003 in weekly passes with turnaround times of typically three to four days.

  5. Analyzing Distributed Functions in an Integrated Hazard Analysis

    Science.gov (United States)

    Morris, A. Terry; Massie, Michael J.

    2010-01-01

    Large scale integration of today's aerospace systems is achievable through the use of distributed systems. Validating the safety of distributed systems is significantly more difficult as compared to centralized systems because of the complexity of the interactions between simultaneously active components. Integrated hazard analysis (IHA), a process used to identify unacceptable risks and to provide a means of controlling them, can be applied to either centralized or distributed systems. IHA, though, must be tailored to fit the particular system being analyzed. Distributed systems, for instance, must be analyzed for hazards in terms of the functions that rely on them. This paper will describe systems-oriented IHA techniques (as opposed to traditional failure-event or reliability techniques) that should be employed for distributed systems in aerospace environments. Special considerations will be addressed when dealing with specific distributed systems such as active thermal control, electrical power, command and data handling, and software systems (including the interaction with fault management systems). Because of the significance of second-order effects in large scale distributed systems, the paper will also describe how to analyze secondary functions to secondary functions through the use of channelization.

  6. The Solar Wind Ion Analyzer for MAVEN

    Science.gov (United States)

    Halekas, J. S.; Taylor, E. R.; Dalton, G.; Johnson, G.; Curtis, D. W.; McFadden, J. P.; Mitchell, D. L.; Lin, R. P.; Jakosky, B. M.

    2015-12-01

    The Solar Wind Ion Analyzer (SWIA) on the MAVEN mission will measure the solar wind ion flows around Mars, both in the upstream solar wind and in the magneto-sheath and tail regions inside the bow shock. The solar wind flux provides one of the key energy inputs that can drive atmospheric escape from the Martian system, as well as in part controlling the structure of the magnetosphere through which non-thermal ion escape must take place. SWIA measurements contribute to the top level MAVEN goals of characterizing the upper atmosphere and the processes that operate there, and parameterizing the escape of atmospheric gases to extrapolate the total loss to space throughout Mars' history. To accomplish these goals, SWIA utilizes a toroidal energy analyzer with electrostatic deflectors to provide a broad 360∘×90∘ field of view on a 3-axis spacecraft, with a mechanical attenuator to enable a very high dynamic range. SWIA provides high cadence measurements of ion velocity distributions with high energy resolution (14.5 %) and angular resolution (3.75∘×4.5∘ in the sunward direction, 22.5∘×22.5∘ elsewhere), and a broad energy range of 5 eV to 25 keV. Onboard computation of bulk moments and energy spectra enable measurements of the basic properties of the solar wind at 0.25 Hz.

  7. Analyzing and Mining Ordered Information Tables

    Institute of Scientific and Technical Information of China (English)

    SAI Ying (赛英); Y. Y. Yao

    2003-01-01

    Work in inductive learning has mostly been concentrated on classifying. However,there are many applications in which it is desirable to order rather than to classify instances. For modelling ordering problems, we generalize the notion of information tables to ordered information tables by adding order relations in attribute values. Then we propose a data analysis model by analyzing the dependency of attributes to describe the properties of ordered information tables.The problem of mining ordering rules is formulated as finding association between orderings of attribute values and the overall ordering of objects. An ordering rules may state that "if the value of an object x on an attribute a is ordered ahead of the value of another object y on the same attribute, then x is ordered ahead of y". For mining ordering rules, we first transform an ordered information table into a binary information table, and then apply any standard machine learning and data mining algorithms. As an illustration, we analyze in detail Maclean's universities ranking for the year 2000.

  8. The MAVEN Solar Wind Electron Analyzer

    Science.gov (United States)

    Mitchell, D. L.; Mazelle, C.; Sauvaud, J.-A.; Thocaven, J.-J.; Rouzaud, J.; Fedorov, A.; Rouger, P.; Toublanc, D.; Taylor, E.; Gordon, D.; Robinson, M.; Heavner, S.; Turin, P.; Diaz-Aguado, M.; Curtis, D. W.; Lin, R. P.; Jakosky, B. M.

    2016-04-01

    The MAVEN Solar Wind Electron Analyzer (SWEA) is a symmetric hemispheric electrostatic analyzer with deflectors that is designed to measure the energy and angular distributions of 3-4600-eV electrons in the Mars environment. This energy range is important for impact ionization of planetary atmospheric species, and encompasses the solar wind core and halo populations, shock-energized electrons, auroral electrons, and ionospheric primary photoelectrons. The instrument is mounted at the end of a 1.5-meter boom to provide a clear field of view that spans nearly 80 % of the sky with ˜20° resolution. With an energy resolution of 17 % (Δ E/E), SWEA readily distinguishes electrons of solar wind and ionospheric origin. Combined with a 2-second measurement cadence and on-board real-time pitch angle mapping, SWEA determines magnetic topology with high (˜8-km) spatial resolution, so that local measurements of the plasma and magnetic field can be placed into global context.

  9. Analyzing delay causes in Egyptian construction projects

    Directory of Open Access Journals (Sweden)

    Mohamed M. Marzouk

    2014-01-01

    Full Text Available Construction delays are common problems in civil engineering projects in Egypt. These problems occur frequently during project life-time leading to disputes and litigation. Therefore, it is essential to study and analyze causes of construction delays. This research presents a list of construction delay causes retrieved from literature. The feedback of construction experts was obtained through interviews. Subsequently, a questionnaire survey was prepared. The questionnaire survey was distributed to thirty-three construction experts who represent owners, consultants, and contractor’s organizations. Frequency Index, Severity Index, and Importance Index are calculated and according to the highest values of them the top ten delay causes of construction projects in Egypt are determined. A case study is analyzed and compared to the most important delay causes in the research. Statistical analysis is carried out using analysis of variance ANOVA method to test delay causes, obtained from the survey. The test results reveal good correlation between groups while there is significant difference between them for some delay causes and finally roadmap for prioritizing delay causes groups is presented.

  10. Sentiment Analyzer for Arabic Comments System

    Directory of Open Access Journals (Sweden)

    Alaa El-Dine Ali Hamouda

    2013-04-01

    Full Text Available Today, the number of users of social network is increasing. Millions of users share opinions on different aspects of life every day. Therefore social network are rich sources of data for opinion mining and sentiment analysis. Also users have become more interested in following news pages on Facebook. Several posts; political for example, have thousands of users’ comments that agree/disagree with the post content. Such comments can be a good indicator for the community opinion about the post content. For politicians, marketers, decision makers …, it is required to make sentiment analysis to know the percentage of users agree, disagree and neutral respect to a post. This raised the need to analyze theusers’ comments in Facebook. We focused on Arabic Facebook news pages for the task of sentiment analysis. We developed a corpus for sentiment analysis and opinion mining purposes. Then, we used different machine learning algorithms – decision tree, support vector machines, and naive bayes - to develop sentiment analyzer. The performance of the system using each technique was evaluated and compared with others.

  11. Analyzing Network Coding Gossip Made Easy

    CERN Document Server

    Haeupler, Bernhard

    2010-01-01

    We give a new technique to analyze the stopping time of gossip protocols that are based on random linear network coding (RLNC). Our analysis drastically simplifies, extends and strengthens previous results. We analyze RLNC gossip in a general framework for network and communication models that encompasses and unifies the models used previously in this context. We show, in most settings for the first time, that it converges with high probability in the information-theoretically optimal time. Most stopping times are of the form O(k + T) where k is the number of messages to be distributed and T is the time it takes to disseminate one message. This means RLNC gossip achieves "perfect pipelining". Our analysis directly extends to highly dynamic networks in which the topology can change completely at any time. This remains true even if the network dynamics are controlled by a fully adaptive adversary that knows the complete network state. Virtually nothing besides simple O(kT) sequential flooding protocols was prev...

  12. Calibration of the portable wear metal analyzer

    Science.gov (United States)

    Quinn, Michael J.

    1987-12-01

    The Portable Wear Metal Analyzer (PWMA), a graphite furnace atomic absorption (AA) spectrometer, developed under a contract for this laboratory, was evaluated using powdered metal particles suspended in oil. The PWMA is a microprocessor controlled automatic sequential multielement AA spectrometer designed to support the deployed aircraft requirement for spectrometric oil analysis. The PWMA will analyze for nine elements (Ni, Fe, Cu, Cr, Ag, Mg, Si, Ti, Al) at a rate of 4 min per sample. The graphite tube and modified sample introduction system increase the detection of particles in oil when compared to the currently used techniques of flame AA or spark atomic emission (AE) spectroscopy. The PWMA shows good-to-excellent response for particles in sizes of 0 to 5 and 5 to 10 micrometers and fair response to particles of 10 to 20 and 20 to 30 micrometers. All trends in statistical variations are easily explained by system considerations. Correction factors to the calibration curves are necessary to correlate the analytical capability of the PWMA to the performance of existing spectrometric oil analysis (SOA) instruments.

  13. Analyzing Interoperability of Protocols Using Model Checking

    Institute of Scientific and Technical Information of China (English)

    WUPeng

    2005-01-01

    In practical terms, protocol interoperability testing is still laborious and error-prone with little effect, even for those products that have passed conformance testing. Deadlock and unsymmetrical data communication are familiar in interoperability testing, and it is always very hard to trace their causes. The previous work has not provided a coherent way to analyze why the interoperability was broken among protocol implementations under test. In this paper, an alternative approach is presented to analyzing these problems from a viewpoint of implementation structures. Sequential and concurrent structures are both representative implementation structures, especially in event-driven development model. Our research mainly discusses the influence of sequential and concurrent structures on interoperability, with two instructive conclusions: (a) a sequential structure may lead to deadlock; (b) a concurrent structure may lead to unsymmetrical data communication. Therefore, implementation structures carry weight on interoperability, which may not gain much attention before. To some extent, they are decisive on the result of interoperability testing. Moreover, a concurrent structure with a sound task-scheduling strategy may contribute to the interoperability of a protocol implementation. Herein model checking technique is introduced into interoperability analysis for the first time. As the paper shows, it is an effective way to validate developers' selections on implementation structures or strategies.

  14. Diamond Analyzed by Secondary Electron Emission Spectroscopy

    Science.gov (United States)

    Krainsky, Isay L.

    1998-01-01

    Diamond is a promising semiconductor material for novel electronic applications because of its chemical stability and inertness, heat conduction properties, and so-called negative electron affinity (NEA). When a surface has NEA, electrons generated inside the bulk of the material are able to come out into the vacuum without any potential barrier (work function). Such a material would have an extremely high secondary electron emission coefficient o, very high photoelectron (quantum) yield, and would probably be an efficient field emitter. Chemical-vapor-deposited (CVD) polycrystalline diamond films have even more advantages than diamond single crystals. Their fabrication is relatively easy and inexpensive, and they can be grown with high levels of doping--consequently, they can have relatively high conductivity. Because of these properties, diamond can be used for cold cathodes and photocathodes in high-power electronics and in high-frequency and high-temperature semiconductor devices.

  15. Improving physics instruction by analyzing video games

    Science.gov (United States)

    Beatty, Ian D.

    2013-01-01

    Video games can be very powerful teaching systems, and game designers have become adept at optimizing player engagement while scaffolding development of complex skills and situated knowledge. One implication is that we might create games to teach physics. Another, which I explore here, is that we might learn to improve classroom physics instruction by studying effective games. James Gee, in his book What Video Games Have to Teach Us About Learning and Literacy (2007), articulates 36 principles that make good video games highly effective as learning environments. In this theoretical work, I identify 16 themes running through Gee's principles, and explore how these themes and Gee's principles could be applied to the design of an on-campus physics course. I argue that the process pushes us to confront aspects of learning that physics instructors and even physics education researchers generally neglect, and suggest some novel ideas for course design.

  16. Automated Root Tracking with "Root System Analyzer"

    Science.gov (United States)

    Schnepf, Andrea; Jin, Meina; Ockert, Charlotte; Bol, Roland; Leitner, Daniel

    2015-04-01

    Crucial factors for plant development are water and nutrient availability in soils. Thus, root architecture is a main aspect of plant productivity and needs to be accurately considered when describing root processes. Images of root architecture contain a huge amount of information, and image analysis helps to recover parameters describing certain root architectural and morphological traits. The majority of imaging systems for root systems are designed for two-dimensional images, such as RootReader2, GiA Roots, SmartRoot, EZ-Rhizo, and Growscreen, but most of them are semi-automated and involve mouse-clicks in each root by the user. "Root System Analyzer" is a new, fully automated approach for recovering root architectural parameters from two-dimensional images of root systems. Individual roots can still be corrected manually in a user interface if required. The algorithm starts with a sequence of segmented two-dimensional images showing the dynamic development of a root system. For each image, morphological operators are used for skeletonization. Based on this, a graph representation of the root system is created. A dynamic root architecture model helps to determine which edges of the graph belong to an individual root. The algorithm elongates each root at the root tip and simulates growth confined within the already existing graph representation. The increment of root elongation is calculated assuming constant growth. For each root, the algorithm finds all possible paths and elongates the root in the direction of the optimal path. In this way, each edge of the graph is assigned to one or more coherent roots. Image sequences of root systems are handled in such a way that the previous image is used as a starting point for the current image. The algorithm is implemented in a set of Matlab m-files. Output of Root System Analyzer is a data structure that includes for each root an identification number, the branching order, the time of emergence, the parent

  17. Stackable differential mobility analyzer for aerosol measurement

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Meng-Dawn (Oak Ridge, TN); Chen, Da-Ren (Creve Coeur, MO)

    2007-05-08

    A multi-stage differential mobility analyzer (MDMA) for aerosol measurements includes a first electrode or grid including at least one inlet or injection slit for receiving an aerosol including charged particles for analysis. A second electrode or grid is spaced apart from the first electrode. The second electrode has at least one sampling outlet disposed at a plurality different distances along its length. A volume between the first and the second electrode or grid between the inlet or injection slit and a distal one of the plurality of sampling outlets forms a classifying region, the first and second electrodes for charging to suitable potentials to create an electric field within the classifying region. At least one inlet or injection slit in the second electrode receives a sheath gas flow into an upstream end of the classifying region, wherein each sampling outlet functions as an independent DMA stage and classifies different size ranges of charged particles based on electric mobility simultaneously.

  18. Analyzing Options for Airborne Emergency Wireless Communications

    Energy Technology Data Exchange (ETDEWEB)

    Michael Schmitt; Juan Deaton; Curt Papke; Shane Cherry

    2008-03-01

    In the event of large-scale natural or manmade catastrophic events, access to reliable and enduring commercial communication systems is critical. Hurricane Katrina provided a recent example of the need to ensure communications during a national emergency. To ensure that communication demands are met during these critical times, Idaho National Laboratory (INL) under the guidance of United States Strategic Command has studied infrastructure issues, concerns, and vulnerabilities associated with an airborne wireless communications capability. Such a capability could provide emergency wireless communications until public/commercial nodes can be systematically restored. This report focuses on the airborne cellular restoration concept; analyzing basic infrastructure requirements; identifying related infrastructure issues, concerns, and vulnerabilities and offers recommended solutions.

  19. Fully Analyzing an Algebraic Polya Urn Model

    CERN Document Server

    Morcrette, Basile

    2012-01-01

    This paper introduces and analyzes a particular class of Polya urns: balls are of two colors, can only be added (the urns are said to be additive) and at every step the same constant number of balls is added, thus only the color compositions varies (the urns are said to be balanced). These properties make this class of urns ideally suited for analysis from an "analytic combinatorics" point-of-view, following in the footsteps of Flajolet-Dumas-Puyhaubert, 2006. Through an algebraic generating function to which we apply a multiple coalescing saddle-point method, we are able to give precise asymptotic results for the probability distribution of the composition of the urn, as well as local limit law and large deviation bounds.

  20. Statistical network analysis for analyzing policy networks

    DEFF Research Database (Denmark)

    Robins, Garry; Lewis, Jenny; Wang, Peng

    2012-01-01

    To analyze social network data using standard statistical approaches is to risk incorrect inference. The dependencies among observations implied in a network conceptualization undermine standard assumptions of the usual general linear models. One of the most quickly expanding areas of social and...... policy network methodology is the development of statistical modeling approaches that can accommodate such dependent data. In this article, we review three network statistical methods commonly used in the current literature: quadratic assignment procedures, exponential random graph models (ERGMs), and...... stochastic actor-oriented models. We focus most attention on ERGMs by providing an illustrative example of a model for a strategic information network within a local government. We draw inferences about the structural role played by individuals recognized as key innovators and conclude that such an approach...

  1. Detect Adjacent Well by Analyzing Geomagnetic Anomalies

    Directory of Open Access Journals (Sweden)

    Su Zhang

    2014-03-01

    Full Text Available This study describes a method of determining the position of adjacent well by analyzing geomagnetic anomalies in the drilling. In the experiment, put a casing in the geomagnetic field respectively to simulate 3 conditions, which are vertical well, deviated well and horizontal well. Study the interference of regional geomagnetic caused by casing, summary the law of the regional geomagnetic field anomalies caused by the adjacent casing. Experimental results show that: magnetic intensity distortion caused by deviated well is similar to that caused by horizontal well, but the distortion is different from vertical well. The scope and amplitude of N and E component magnetic intensity distortion will increase with the increase of casing inclination, meanwhile the scope and amplitude of V component distortion will decrease and the distortion value changes from negative to positive to the southwest of adjacent well. Through the analysis of geomagnetic anomalies, the position of the adjacent wells could be determined.

  2. Coke from small-diameter tubes analyzed

    International Nuclear Information System (INIS)

    The mechanism for coke deposit formation and the nature of the coke itself can vary with the design of the ethylene furnace tube bank. In this article, coke deposits from furnaces with small-diameter pyrolysis tubes are examined. The samples were taken from four furnaces of identical design (Plant B). As in both the first and second installments of the series, the coke deposits were examined using a scanning electron microscope (SEM) and an energy dispersive X-ray analyzer (EDAX). The deposits from the small-diameter tubes are compared with the coke deposits from the furnace discussed in earlier articles. Analysis of the coke in both sets of samples are then used to offer recommendations for improved decoking procedures, operating procedures, better feed selection, and better selection of the metallurgy used in furnace tubes, to extend the operating time of the furnace tubes by reducing the amount and type of coke build up

  3. Composite blade structural analyzer (COBSTRAN) user's manual

    Science.gov (United States)

    Aiello, Robert A.

    1989-01-01

    The installation and use of a computer code, COBSTRAN (COmposite Blade STRuctrual ANalyzer), developed for the design and analysis of composite turbofan and turboprop blades and also for composite wind turbine blades was described. This code combines composite mechanics and laminate theory with an internal data base of fiber and matrix properties. Inputs to the code are constituent fiber and matrix material properties, factors reflecting the fabrication process, composite geometry and blade geometry. COBSTRAN performs the micromechanics, macromechanics and laminate analyses of these fiber composites. COBSTRAN generates a NASTRAN model with equivalent anisotropic homogeneous material properties. Stress output from NASTRAN is used to calculate individual ply stresses, strains, interply stresses, thru-the-thickness stresses and failure margins. Curved panel structures may be modeled providing the curvature of a cross-section is defined by a single value function. COBSTRAN is written in FORTRAN 77.

  4. Composite Blade Structural Analyzer (COBSTRAN) demonstration manual

    Science.gov (United States)

    Aiello, Robert A.

    1989-01-01

    The input deck setup is described for a computer code, composite blade structural analyzer (COBSTRAN) which was developed for the design and analysis of composite turbofan and turboprop blades and also for composite wind turbine blades. This manual is intended for use in conjunction with the COBSTRAN user's manual. Seven demonstration problems are described with pre- and postprocessing input decks. Modeling of blades which are solid thru-the-thickness and also aircraft wing airfoils with internal spars is shown. Corresponding NASTRAN and databank input decks are also shown. Detail descriptions of each line of the pre- and post-processing decks is provided with reference to the Card Groups defined in the user's manual. A dictionary of all program variables and terms used in this manual may be found in Section 6 of the user's manual.

  5. Analyzing hydrological sustainability through water balance.

    Science.gov (United States)

    Menció, Anna; Folch, Albert; Mas-Pla, Josep

    2010-05-01

    The objective of the Water Framework Directive (2000/60/EC) is to assist in the development of management plans that will lead to the sustainable use of water resources in all EU member states. However, defining the degree of sustainability aimed at is not a straightforward task. It requires detailed knowledge of the hydrogeological characteristics of the basin in question, its environmental needs, the amount of human water demand, and the opportunity to construct a proper water balance that describes the behavior of the hydrological system and estimates available water resources. An analysis of the water balance in the Selva basin (Girona, NE Spain) points to the importance of regional groundwater fluxes in satisfying current exploitation rates, and shows that regional scale approaches are often necessary to evaluate water availability. In addition, we discuss the pressures on water resources, and analyze potential actions, based on the water balance results, directed towards achieving sustainable water management in the basin. PMID:20229067

  6. Method and apparatus for analyzing ionizable materials

    International Nuclear Information System (INIS)

    An apparatus and method are described for analyzing a solution of ionizable compounds in a liquid. The solution is irradiated with electromagnetic radiation to ionize the compounds and the electrical conductivity of the solution is measured. The radiation may be X-rays, ultra-violet, infra-red or microwaves. The solution may be split into two streams, only one of which is irradiated, the other being used as a reference by comparing conductivities of the two streams. The liquid must be nonionizable and is preferably a polar solvent. The invention provides an analysis technique useful in liquid chromatography and in gas chromatography after dissolving the eluted gases in a suitable solvent. Electrical conductivity measurements performed on the irradiated eluent provide a quantitative indication of the ionizable materials existing within the eluent stream and a qualitative indication of the purity of the eluent stream. (author)

  7. Analyzing, Modelling, and Designing Software Ecosystems

    DEFF Research Database (Denmark)

    Manikas, Konstantinos

    the development, implementation, and use of telemedicine services. We initially expand the theory of software ecosystems by contributing to the definition and understanding of software ecosystems, providing means of analyzing existing and designing new ecosystems, and defining and measuring the...... qualities of software ecosystems. We use these contributions to design a software ecosystem in the telemedicine services of Denmark with (i) a common platform that supports and promotes development from different actors, (ii) high software interaction, (iii) strong social network of actors, (iv) robust...... thesis documents the groundwork towards addressing the challenges faced by telemedical technologies today and establishing telemedicine as a means of patient diagnosis and treatment. Furthermore, it serves as an empirical example of designing a software ecosystem....

  8. Analyzing and forecasting the European social climate

    Directory of Open Access Journals (Sweden)

    Liliana DUGULEANĂ

    2015-06-01

    Full Text Available The paper uses the results of the sample survey Eurobarometer, which has been requested by the European Commission. The social climate index is used to measure the level of perceptions of population by taking into account their personal situation and their perspective at national level. The paper makes an analysis of the evolution of social climate indices for the countries of European Union and offers information about the expectations of population of analyzed countries. The obtained results can be compared with the forecasting of Eurobarometer, on short term of one year and medium term of five years. Modelling the social climate index and its influence factors offers useful information about the efficiency of social protection and inclusion policies.

  9. Nuclear Plant Analyzer: Installation manual. Volume 1

    International Nuclear Information System (INIS)

    This report contains the installation instructions for the Nuclear Plant Analyzer (NPA) System. The NPA System consists of the Computer Visual System (CVS) program, the NPA libraries, the associated utility programs. The NPA was developed at the Idaho National Engineering Laboratory under the sponsorship of the US Nuclear Regulatory Commission to provide a highly flexible graphical user interface for displaying the results of these analysis codes. The NPA also provides the user with a convenient means of interactively controlling the host program through user-defined pop-up menus. The NPA was designed to serve primarily as an analysis tool. After a brief introduction to the Computer Visual System and the NPA, an analyst can quickly create a simple picture or set of pictures to aide in the study of a particular phenomenon. These pictures can range from simple collections of square boxes and straight lines to complex representations of emergency response information displays

  10. Complex networks theory for analyzing metabolic networks

    Institute of Scientific and Technical Information of China (English)

    ZHAO Jing; YU Hong; LUO Jianhua; CAO Z.W.; LI Yixue

    2006-01-01

    One of the main tasks of post-genomic informatics is to systematically investigate all molecules and their interactions within a living cell so as to understand how these molecules and the interactions between them relate to the function of the organism,while networks are appropriate abstract description of all kinds of interactions. In the past few years, great achievement has been made in developing theory of complex networks for revealing the organizing principles that govern the formation and evolution of various complex biological, technological and social networks. This paper reviews the accomplishments in constructing genome-based metabolic networks and describes how the theory of complex networks is applied to analyze metabolic networks.

  11. Color recognition system for urine analyzer

    Science.gov (United States)

    Zhu, Lianqing; Wang, Zicai; Lin, Qian; Dong, Mingli

    2010-08-01

    In order to increase the speed of photoelectric conversion, a linear CCD is applied as the photoelectric converter instead of the traditional photodiode. A white LED is used as the light source of the system. The color information of the urine test strip is transferred into the CCD through a reflecting optical system. It is then converted to digital signals by an A/D converter. The test results of urine analysis are obtained by a data processing system. An ARM microprocessor is selected as the CPU of the system and a CPLD is employed to provide a driving timing for the CCD drive and the A/D converter. Active HDL7.2 and Verilog HDL are used to simulate the driving timing of the CPLD. Experimental results show that the correctness rate of the test results is better than 90%. The system satisfies the requirements of the color information collection of urine analyzer.

  12. A miniaturized stepwise injection spectrophotometric analyzer

    International Nuclear Information System (INIS)

    A novel micro-stepwise injection analyzer (μSWIA) has been developed for the automation and miniaturization of spectrophotometric analysis. The main unit of this device is a mixing chamber (MC) connected to the atmosphere. This part of the μSWIA provides rapid and effective homogenization of the reaction mixture components and completion of the reaction by means of gas bubbling. The μSWIA contained a rectangular labyrinth channel designed in way allowing one to eliminate bubbles by moving a solution from the MC to an optical channel. The light-emitting diode (LED) was used as a light emitter and the analytical signal was measured by a portable spectrophotometer. Fluid movement was attained via the use of a computer-controlled syringe pump. The μSWIA was successfully used for the spectrophotometric determination of cysteine in biologically active supplements and fodder by using 18-molybdo-2-phosphate heteropoly anion (18-MPA) as the reagent. (author)

  13. Electrode contamination effects of retarding potential analyzer.

    Science.gov (United States)

    Fang, H K; Oyama, K-I; Cheng, C Z

    2014-01-01

    The electrode contamination in electrostatic analyzers such as Langmuir probes and retarding potential analyzers (RPA) is a serious problem for space measurements. The contamination layer acts as extra capacitance and resistance and leads to distortion in the measured I-V curve, which leads to erroneous measurement results. There are two main effects of the contamination layer: one is the impedance effect and the other is the charge attachment and accumulation due to the capacitance. The impedance effect can be reduced or eliminated by choosing the proper sweeping frequency. However, for RPA the charge accumulation effect becomes serious because the capacitance of the contamination layer is much larger than that of the Langmuir probe of similar dimension. The charge accumulation on the retarding potential grid causes the effective potential, that ions experience, to be changed from the applied voltage. Then, the number of ions that can pass through the retarding potential grid to reach the collector and, thus, the measured ion current are changed. This effect causes the measured ion drift velocity and ion temperature to be changed from the actual values. The error caused by the RPA electrode contamination is expected to be significant for sounding rocket measurements with low rocket velocity (1-2 km/s) and low ion temperature of 200-300 K in the height range of 100-300 km. In this paper we discuss the effects associated with the RPA contaminated electrodes based on theoretical analysis and experiments performed in a space plasma operation chamber. Finally, the development of a contamination-free RPA for sounding rocket missions is presented. PMID:24517809

  14. Analyzing large biological datasets with association networks

    Energy Technology Data Exchange (ETDEWEB)

    Karpinets, Tatiana V [ORNL; Park, Byung H [ORNL; Uberbacher, Edward C [ORNL

    2012-01-01

    Due to advances in high throughput biotechnologies biological information is being collected in databases at an amazing rate, requiring novel computational approaches for timely processing of the collected data into new knowledge. In this study we address this problem by developing a new approach for discovering modular structure, relationships and regularities in complex data. These goals are achieved by converting records of biological annotations of an object, like organism, gene, chemical, sequence, into networks (Anets) and rules (Arules) of the associated annotations. Anets are based on similarity of annotation profiles of objects and can be further analyzed and visualized providing a compact birds-eye view of most significant relationships in the collected data and a way of their clustering and classification. Arules are generated by Apriori considering each record of annotations as a transaction and augmenting each annotation item by its type. Arules provide a way to validate relationships discovered by Anets producing comprehensive statistics on frequently associated annotations and specific confident relationships among them. A combination of Anets and Arules represents condensed information on associations among the collected data, helping to discover new knowledge and generate hypothesis. As an example we have applied the approach to analyze bacterial metadata from the Genomes OnLine Database. The analysis allowed us to produce a map of sequenced bacterial and archaeal organisms based on their genomic, metabolic and physiological characteristics with three major clusters of metadata representing bacterial pathogens, environmental isolates, and plant symbionts. A signature profile of clustered annotations of environmental bacteria if compared with pathogens linked the aerobic respiration, the high GC content and the large genome size to diversity of metabolic activities and physiological features of the organisms.

  15. Analyzing and Visualizing Whole Program Architectures

    Energy Technology Data Exchange (ETDEWEB)

    Panas, T; Quinlan, D; Vuduc, R

    2007-05-10

    This paper describes our work to develop new tool support for analyzing and visualizing the architecture of complete large-scale (millions or more lines of code) programs. Our approach consists of (i) creating a compact, accurate representation of a whole C or C++ program, (ii) analyzing the program in this representation, and (iii) visualizing the analysis results with respect to the program's architecture. We have implemented our approach by extending and combining a compiler infrastructure and a program visualization tool, and we believe our work will be of broad interest to those engaged in a variety of program understanding and transformation tasks. We have added new whole-program analysis support to ROSE [15, 14], a source-to-source C/C++ compiler infrastructure for creating customized analysis and transformation tools. Our whole-program work does not rely on procedure summaries; rather, we preserve all of the information present in the source while keeping our representation compact. In our representation, a million-line application fits in well less than 1 GB of memory. Because whole-program analyses can generate large amounts of data, we believe that abstracting and visualizing analysis results at the architecture level is critical to reducing the cognitive burden on the consumer of the analysis results. Therefore, we have extended Vizz3D [19], an interactive program visualization tool, with an appropriate metaphor and layout algorithm for representing a program's architecture. Our implementation provides developers with an intuitive, interactive way to view analysis results, such as those produced by ROSE, in the context of the program's architecture. The remainder of this paper summarizes our approach to whole-program analysis (Section 2) and provides an example of how we visualize the analysis results (Section 3).

  16. Transient of power pulse and its sequence in power electronics

    Institute of Scientific and Technical Information of China (English)

    ZHAO ZhengMing; BAI Hua; YUAN LiQiang

    2007-01-01

    Various failures and destructions occur in the applications of the power electronic converter, The real practice shows that these failures are connected with the concentration of the transient power pulse. In allusion to the physical characteristics of power electronic converters, this paper proposed that the power pulse and its sequence are the basis for power electronics in the perspective of electromagnetic energy. The authors analyzed the transient processes in the power semiconductors,electric conduction loops and controller system and illustrated the power pulse phenomena in high voltage and high power inverters. This investigation on the power pulse sequence is very meaningful for the failure analysis and device protection and has become an important topic in power electronics.

  17. Transient of power pulse and its sequence in power electronics

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Various failures and destructions occur in the applications of the power electronic converter. The real practice shows that these failures are connected with the con-centration of the transient power pulse. In allusion to the physical characteristics of power electronic converters,this paper proposed that the power pulse and its se-quence are the basis for power electronics in the perspective of electromagnetic energy. The authors analyzed the transient processes in the power semiconductors,electric conduction loops and controller system and illustrated the power pulse phenomena in high voltage and high power inverters. This investigation on the power pulse sequence is very meaningful for the failure analysis and device pro-tection and has become an important topic in power electronics.

  18. Power Outages

    Science.gov (United States)

    ... Thunderstorms & Lightning Tornadoes Tsunamis Volcanoes Wildfires Main Content Power Outages This page provides basic safety tips and ... during and after a power outage. Before a Power Outage Build or restock your emergency preparedness kit , ...

  19. Power Outages

    Science.gov (United States)

    ... Plants Workplace Plans School Emergency Plans Main Content Power Outages This page provides basic safety tips and ... during and after a power outage. Before a Power Outage Build or restock your emergency preparedness kit , ...

  20. Simulations of the recent Lasalle-2 incident with the BNL plant analyzer

    International Nuclear Information System (INIS)

    This paper presents the results of simulations of the recent power oscillation incident at the LaSalle-2 Nuclear Power Plant using the BNL Plant Analyzer. The causes of the oscillation were investigated and the sensitivity of the oscillation to key parameters was studied. It is concluded that the observed power oscillation was caused by boiling instability (i.e., density wave oscillation) reinforced by the reactivity feedback in neutron kinetics, and that the density wave oscillation resulted from flow reduction due to recirculation pump trip and feedwater temperature reduction due to partial loss of feedwater heating capability as well as power peaking. 7 refs., 9 figs., 1 tab

  1. Simulations of the recent Lasalle-2 incident with the BNL plant analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Chang, H.S.; Mallen, A.N.; Wulff, W.

    1989-01-01

    This paper presents the results of simulations of the recent power oscillation incident at the LaSalle-2 Nuclear Power Plant using the BNL Plant Analyzer. The causes of the oscillation were investigated and the sensitivity of the oscillation to key parameters was studied. It is concluded that the observed power oscillation was caused by boiling instability (i.e., density wave oscillation) reinforced by the reactivity feedback in neutron kinetics, and that the density wave oscillation resulted from flow reduction due to recirculation pump trip and feedwater temperature reduction due to partial loss of feedwater heating capability as well as power peaking. 7 refs., 9 figs., 1 tab.

  2. Power Quality

    OpenAIRE

    Eberhard, Andreas

    2011-01-01

    Electrical power is becoming one of the most dominant factors in our society. Power generation, transmission, distribution and usage are undergoing signifi cant changes that will aff ect the electrical quality and performance needs of our 21st century industry. One major aspect of electrical power is its quality and stability – or so called Power Quality. The view on Power Quality did change over the past few years. It seems that Power Quality is becoming a more important te...

  3. Wind Power

    OpenAIRE

    Makhalas, Kharsan Al; Alsehlli, Faisal

    2015-01-01

    This Bachelor thesis has been written at the Blekinge Institute of Technology. This thesis concentrates on the wind power and their components, also the large wind farm is studied. The electrical power is generated by using the power in wind to drive a wind turbine to produce mechanical power. This mechanical power can be converted into electrical power by using electrical induction generators. There are two types of the wind turbines, the horizontal axis and vertical axis wind turbine, where...

  4. Power System Operation with Large Scale Wind Power Integration

    DEFF Research Database (Denmark)

    Suwannarat, A.; Bak-Jensen, B.; Chen, Z.;

    2007-01-01

    The Danish power system starts to face problems of integrating thousands megawatts of wind power, which produce in a stochastic behavior due to natural wind fluctuations. With wind power capacities increasing, the Danish Transmission System Operator (TSO) is faced with new challenges related to the...... uncertain nature of wind power. In this paper, proposed models of generations and control system are presented which analyze the deviation of power exchange at the western Danish-German border, taking into account the fluctuating nature of wind power. The performance of the secondary control of the thermal...

  5. Analyzing Big Data with Dynamic Quantum Clustering

    CERN Document Server

    Weinstein, M; Hume, A; Sciau, Ph; Shaked, G; Hofstetter, R; Persi, E; Mehta, A; Horn, D

    2013-01-01

    How does one search for a needle in a multi-dimensional haystack without knowing what a needle is and without knowing if there is one in the haystack? This kind of problem requires a paradigm shift - away from hypothesis driven searches of the data - towards a methodology that lets the data speak for itself. Dynamic Quantum Clustering (DQC) is such a methodology. DQC is a powerful visual method that works with big, high-dimensional data. It exploits variations of the density of the data (in feature space) and unearths subsets of the data that exhibit correlations among all the measured variables. The outcome of a DQC analysis is a movie that shows how and why sets of data-points are eventually classified as members of simple clusters or as members of - what we call - extended structures. This allows DQC to be successfully used in a non-conventional exploratory mode where one searches data for unexpected information without the need to model the data. We show how this works for big, complex, real-world dataset...

  6. Analyzing Design Heating Loads in Superinsulated Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Arena, Lois [Consortium for Advanced Residential Buildings, Norwalk, CT (United States)

    2015-06-01

    Super-insulated homes offer many benefits including improved comfort, reduced exterior noise penetration, lower energy bills, and the ability to withstand power and fuel outages under much more comfortable conditions than a typical home. While these homes aren't necessarily constructed with excessive mass in the form of concrete floors and walls, the amount of insulation and the increase in the thickness of the building envelope can lead to a mass effect, resulting in the structures ability to store much more heat than a code built home. This results in a very low thermal inertia making the building much less sensitive to drastic temperature swings thereby decreasing the peak heating load demand. During the winter of 2013/2014, CARB monitored the energy use of three homes in climate zone 6 in an attempt to evaluate the accuracy of two different mechanical system sizing methods for low load homes. Based on the results, it is recommended that internal and solar gains be included and some credit for thermal inertia be used in sizing calculations for super insulated homes.

  7. Pragmatic power

    CERN Document Server

    Eccles, William

    2008-01-01

    Pragmatic Power is focused on just three aspects of the AC electrical power system that supplies and moves the vast majority of electrical energy nearly everywhere in the world: three-phase power systems, transformers, and induction motors. The reader needs to have had an introduction to electrical circuits and AC power, although the text begins with a review of the basics of AC power. Balanced three-phase systems are studied by developing their single-phase equivalents. The study includes a look at how the cost of ""power"" is affected by reactive power and power factor. Transformers are cons

  8. ON COMPLEXITY OF POWER SYSTEMS

    Institute of Scientific and Technical Information of China (English)

    MA Jin; CHENG Daizhan; HONG Yiguang; SUN Yuanzhang

    2003-01-01

    The power system is a classical example of complex systems. In this paper it is shown that the power industry in China is facing a tremendous challenge. The complexity in power systems is investigated as follows. First, the cascade failure in power systems is analyzed, and compared with sand-pile model. Next, we show that the agent-based modelling is a proper way for power network. Mathematically, the geometric dynamics and differential inclusion are useful tools for the stability analysis of large scale power systems. As for power market, the game theory and generalized control system model are proposed. For a complex power system, an evolutive model may be more accurate in description and analysis. Finally, certain newly developed numerical methods in the power system computation are introduced. Overall, we are convinced that the theorem of complexity, combined with modern control theory, may be the right way to answer the challenges faced by the power industry in China.

  9. Programmable calculator: alternative to minicomputer-based analyzer

    International Nuclear Information System (INIS)

    Described are a number of typical field and laboratory counting systems that use standard stand-alone multichannel analyzers (MCA) interfaced to a Hewlett-Packard Company (HP 9830) programmable calculator. Such systems can offer significant advantages in cost and flexibility over a minicomputyr-based system. Because most laboratories tend to accumulate MCA's over the years, the programmable calculator also offers an easy way to upgrade the laboratory while making optimum use of existing systems. Software programs are easily tailored to fit a variety of general or specific applications. The only disadvantage of the calculator vs a computer-based system is in speed of analyses; however, for most applications this handicap is minimal. Applications discussed give a brief overview of the power and flexibility of the MCA-calculator approach to automated counting and data reduction

  10. Using linear programming to analyze and optimize stochastic flow lines

    DEFF Research Database (Denmark)

    Helber, Stefan; Schimmelpfeng, Katja; Stolletz, Raik; Lagershausen, Svenja

    2011-01-01

    , to determine a production rate estimate. As our methodology is purely numerical, it offers the full modeling flexibility of stochastic simulation with respect to the probability distribution of processing times. However, unlike discrete-event simulation models, it also offers the optimization power......This paper presents a linear programming approach to analyze and optimize flow lines with limited buffer capacities and stochastic processing times. The basic idea is to solve a huge but simple linear program that models an entire simulation run of a multi-stage production process in discrete time...... of linear programming and hence allows us to solve buffer allocation problems. We show under which conditions our method works well by comparing its results to exact values for two-machine models and approximate simulation results for longer lines....

  11. Analyzing the New York Global History and Geography Exam

    Directory of Open Access Journals (Sweden)

    S. G. Grant

    2001-10-01

    Full Text Available Education Week's report "Quality Counts" judges New York State's curriculum and assessment policy efforts to be an "A." Surface-level reviews such as "Quality Counts" tell something about the workings of state policy, but they are more useful as snapshots than as well-developed portraits of curriculum and assessment change. In this article, I analyze the new New York State Global History and Geography standards and tests using a set of social studies-specific criteria which inquire deeply into the implications for real instructional change. From that vantage, I argue that New York's policy efforts, while seemingly well-intentioned and reflective of surface-level change, fail to promote powerful teaching and learning in social studies. Teachers intent on producing ambitious teaching and learning will find little to interfere with their efforts. But as a set of reforms intended to encourage substantive change, the new global history test falls short.

  12. Enabling Wind Power Nationwide

    Energy Technology Data Exchange (ETDEWEB)

    Jose Zayas, Michael Derby, Patrick Gilman and Shreyas Ananthan,

    2015-05-01

    Leveraging this experience, the U.S. Department of Energy’s (DOE’s) Wind and Water Power Technologies Office has evaluated the potential for wind power to generate electricity in all 50 states. This report analyzes and quantifies the geographic expansion that could be enabled by accessing higher above ground heights for wind turbines and considers the means by which this new potential could be responsibly developed.

  13. RELIABILITY IN POWER SYSTEM

    OpenAIRE

    Aleksander Uklański

    1983-01-01

    The study is an attempt to apply the concept of reliability, the most important feature of operating machinery and equipment technioznych, the national power system which is one of the major, if not essential part of the national economy. It is a serial structure of the system, and the members of this structure, as subsystems. It shows that a decisive role in achieving reliability is a subsystem manufacturing, and the teams of steam power units. Analyze the reliability of boilers, pipelines, ...

  14. Qualitative Methodology in Analyzing Educational Phenomena

    Directory of Open Access Journals (Sweden)

    Antonio SANDU

    2010-12-01

    Full Text Available Semiological analysis of educational phenomena allow researchers access to a multidimensional universe of meanings that is represented by the school, not so much seen as an institution, but as a vector of social action through educational strategies. We consider education as a multidimensional phenomenon since its analysis allows the researcher to explore a variety of research hypotheses of different paradigmatic perspectives that converge in an educational finality. According to the author Simona Branc one of the most appropriate methods used in qualitative data analysis is Grounded Theory; this one assumes a systematic process of generating concepts and theories based on the data collected. Specialised literature defines Grounded Theory as an inductive approach that starts with general observations and during the analytical process creates conceptual categories that explain the theme explored. Research insist on the role of the sociologic theory of managing the research data and for providing ways of conceptualizing the descriptions and explanations.Qualitative content analysis is based on the constructivist paradigm (constructionist in the restricted sense that we used previously. It aims to create an “understanding of the latent meanings of the analyzed messages”. Quantitative content analysis involves a process of encoding and statistical analysis of data extracted from the content of the paper in the form of extractions like: frequencies, contingency analysis, etc

  15. Analyzing Consumer Behavior Towards Contemporary Food Retailers

    Directory of Open Access Journals (Sweden)

    E.Dursun

    2008-01-01

    Full Text Available The objective of this research is analyzing consumer behaviors towards to contemporary food retailers. Food retailing has been changing during recent years in Turkey. Foreign investors captivated with this market potential of food retailing. Retailer‟s format has been changed and featuring large-scale, extended product variety and full service retailers spreading rapidly through the nation-wide. Consumers‟ tend to shop their household needs from contemporary retailers due mainly to urbanism, increasing women workforce and income growth. In this research, original data collected through face-to-face interview from 385 respondents which are located in Istanbul. Different Socio-Economic Status (SES groups‟ ratio for Istanbul was forming sampling distribution. Consumers prefer closest food retailers which are mainly purchasing food products. Consumers purchase more than their planned what their needs; especially C SES group average comes first for the spending money for unplanned shopping. Chain stores and hypermarkets are the most preferred retailers in food purchasing. Moreover, consumer responses to judgments related to retailing are being investigating with factor analysis.

  16. Analyzing waterflood responses for Pekisko B

    Energy Technology Data Exchange (ETDEWEB)

    Fedenczuk, L. [Gambit Consulting Ltd., (Canada); Pedersen, P.; Marshall, M. [Ocelot Energy Inc., Calgary, AB (Canada)

    1999-11-01

    A study was conducted between January 1990 and September 1997 to find fluid communication between injectors and producers in the Pekisko B pool, the largest oil pool in the Sylvan Lake Field, and the third largest oil pool in the Gilby, Medicine River and Sylvan Lake Field areas in Alberta. A total of eight injectors (patterns) and all wells within a radius of 1700 m from any specific injector were analyzed. The analysis was based on responses of producers to change in the injection rates. The strength of the oil response was measured as the correlation between the oil rate and the injection rate. Three sets of primary parameters characterized the oil, gas and water response. The waterflood responses were presented in the form of special XY diagrams. All injectors showed medium or strong communication with producers as defined by the oil responses. This method of finding fluid responses proved to be more cost and time effective than conventional engineering methods. 4 refs., 8 figs.

  17. Complete denture analyzed by optical coherence tomography

    Science.gov (United States)

    Negrutiu, Meda L.; Sinescu, Cosmin; Todea, Carmen; Podoleanu, Adrian G.

    2008-02-01

    The complete dentures are currently made using different technologies. In order to avoid deficiencies of the prostheses made using the classical technique, several alternative systems and procedures were imagined, directly related to the material used and also to the manufacturing technology. Thus, at the present time, there are several injecting systems and technologies on the market, that use chemoplastic materials, which are heat cured (90-100°C), in dry or wet environment, or cold cured (below 60°C). There are also technologies that plasticize a hard cured material by thermoplastic processing (without any chemical changes) and then inject it into a mold. The purpose of this study was to analyze the existence of possible defects in several dental prostheses using a non invasive method, before their insertion in the mouth. Different dental prostheses, fabricated from various materials were investigated using en-face optical coherence tomography. In order to discover the defects, the scanning was made in three planes, obtaining images at different depths, from 0,01 μm to 2 mm. In several of the investigated prostheses we found defects which may cause their fracture. These defects are totally included in the prostheses material and can not be vizualised with other imagistic methods. In conclusion, en-face OCT is an important investigative tool for the dental practice.

  18. Eastern Mediterranean Natural Gas: Analyzing Turkey's Stance

    Directory of Open Access Journals (Sweden)

    Abdullah Tanriverdi

    2016-02-01

    Full Text Available Recent large-scale natural gas discoveries in East Mediterranean have drawn attention to the region. The discoveries caused both hope and tension in the region. As stated, the new resources may serve as a new hope for all relevant parties as well as the region if managed in a collaborative and conciliatory way. Energy may be a remedy to Cyprus' financial predicament, initiate a process for resolving differences between Turkey and Cyprus, normalize Israel-Turkey relations and so on. On the contrary, adopting unilateral and uncooperative approach may aggravate the tension and undermine regional stability and security. In this sense, the role of energy in generating hope or tension is dependent on the approaches of related parties. The article will analyze Turkey's attitude in East Mediterranean case in terms of possible negative and positive implications for Turkey in the energy field. The article examines Turkey's position and the reasons behind its stance in the East Mediterranean case. Considering Turkey's energy profile and energy policy goals, the article argues that the newly found hydrocarbons may bring in more stakes for Turkey if Turkey adopts a cooperative approach in this case.

  19. Analyzing Spatiotemporal Anomalies through Interactive Visualization

    Directory of Open Access Journals (Sweden)

    Tao Zhang

    2014-06-01

    Full Text Available As we move into the big data era, data grows not just in size, but also in complexity, containing a rich set of attributes, including location and time information, such as data from mobile devices (e.g., smart phones, natural disasters (e.g., earthquake and hurricane, epidemic spread, etc. We are motivated by the rising challenge and build a visualization tool for exploring generic spatiotemporal data, i.e., records containing time location information and numeric attribute values. Since the values often evolve over time and across geographic regions, we are particularly interested in detecting and analyzing the anomalous changes over time/space. Our analytic tool is based on geographic information system and is combined with spatiotemporal data mining algorithms, as well as various data visualization techniques, such as anomaly grids and anomaly bars superimposed on the map. We study how effective the tool may guide users to find potential anomalies through demonstrating and evaluating over publicly available spatiotemporal datasets. The tool for spatiotemporal anomaly analysis and visualization is useful in many domains, such as security investigation and monitoring, situation awareness, etc.

  20. Signal processing and analyzing works of art

    Science.gov (United States)

    Johnson, Don H.; Johnson, C. Richard, Jr.; Hendriks, Ella

    2010-08-01

    In examining paintings, art historians use a wide variety of physico-chemical methods to determine, for example, the paints, the ground (canvas primer) and any underdrawing the artist used. However, the art world has been little touched by signal processing algorithms. Our work develops algorithms to examine x-ray images of paintings, not to analyze the artist's brushstrokes but to characterize the weave of the canvas that supports the painting. The physics of radiography indicates that linear processing of the x-rays is most appropriate. Our spectral analysis algorithms have an accuracy superior to human spot-measurements and have the advantage that, through "short-space" Fourier analysis, they can be readily applied to entire x-rays. We have found that variations in the manufacturing process create a unique pattern of horizontal and vertical thread density variations in the bolts of canvas produced. In addition, we measure the thread angles, providing a way to determine the presence of cusping and to infer the location of the tacks used to stretch the canvas on a frame during the priming process. We have developed weave matching software that employs a new correlation measure to find paintings that share canvas weave characteristics. Using a corpus of over 290 paintings attributed to Vincent van Gogh, we have found several weave match cliques that we believe will refine the art historical record and provide more insight into the artist's creative processes.

  1. PSAIA – Protein Structure and Interaction Analyzer

    Directory of Open Access Journals (Sweden)

    Vlahoviček Kristian

    2008-04-01

    Full Text Available Abstract Background PSAIA (Protein Structure and Interaction Analyzer was developed to compute geometric parameters for large sets of protein structures in order to predict and investigate protein-protein interaction sites. Results In addition to most relevant established algorithms, PSAIA offers a new method PIADA (Protein Interaction Atom Distance Algorithm for the determination of residue interaction pairs. We found that PIADA produced more satisfactory results than comparable algorithms implemented in PSAIA. Particular advantages of PSAIA include its capacity to combine different methods to detect the locations and types of interactions between residues and its ability, without any further automation steps, to handle large numbers of protein structures and complexes. Generally, the integration of a variety of methods enables PSAIA to offer easier automation of analysis and greater reliability of results. PSAIA can be used either via a graphical user interface or from the command-line. Results are generated in either tabular or XML format. Conclusion In a straightforward fashion and for large sets of protein structures, PSAIA enables the calculation of protein geometric parameters and the determination of location and type for protein-protein interaction sites. XML formatted output enables easy conversion of results to various formats suitable for statistic analysis. Results from smaller data sets demonstrated the influence of geometry on protein interaction sites. Comprehensive analysis of properties of large data sets lead to new information useful in the prediction of protein-protein interaction sites.

  2. Toward Integrated μNetwork Analyzer

    Science.gov (United States)

    Kmec, M.; Helbig, M.; Herrmann, R.; Rauschenbach, P.; Sachs, J.; Schilling, K.

    The article deals with recent development steps toward monolithically integrated micro-Network Analyzer (μNA). The device will deploy M-Sequence-based single-chip transceivers with a built-in ultra-wideband wave separation unit in the receiver chains. The introduced on-chip wideband wave separation is realized using an optimized resistive directional coupler combined with a customized differential LNA as detector. The wave separation works almost down to DC, and its upper frequency limit is determined by the performance of the implemented technology (i.e., bridge resistors, transistors, etc.), the selected circuit topology, and the wirings of particular coupler components but also by the IC packaging itself. Even though the upper limit is designed to be compatible with the analog input bandwidth of the receiver circuit [which is about 18 GHz for naked die (Kmec et al., M-Sequence based single chip UWB-radar sensor. ANTEM/AMEREM 2010 Conference, Ottawa, 2010)], the packaged IC is intended for use up to 8 GHz. Finally, the discussed transceiver is a further development of the mother SiGe System-on-Chip (SoC) presented in the work cited above.

  3. The model JSR-12 neutron coincidence analyzer

    International Nuclear Information System (INIS)

    This paper reports that one of the ways in which non-destructive assays for nuclear materials is made involved counting the neutron signatures which result from spontaneous or induced fissions in fissile materials. A major problem in determining the number of fission neutrons is trying to separate them from the background of neutrons arising from alpha particle interactions with lighter nuclei in the matrix materials of the samples being assayed. The JSR-12 neutron coincidence analyzer operates on the principle that fission neutrons occur in multiples of two or more, whereas background neutrons occur randomly as single events. By exploiting this time correlation difference, the JSR-12 can determine the fission neutron signal. This instrument represents a considerable upgrade from the industry standard JSR-11, by doubling the response speed and adding complete computer control of all functions, as well as employing non-volatile memory for data storage. Operation has been simplified for field use by using an LCD display to guide the operator in setting up assay parameters, and by time-date tagging all assays for later retrieval

  4. NRC plant-analyzer development at BNL

    International Nuclear Information System (INIS)

    The objective of this program is to develop an LWR engineering plant analyzer capable of performing realistic and accurate simulations of plant transients and Small-Break Loss of Coolant Accidents at real-time and faster than real-time computing speeds and at low costs for preparing, executing and evaluating such simulations. The program is directed toward facilitating reactor safety analyses, on-line plant monitoring, on-line accident diagnosis and mitigation and toward improving reactor operator training. The AD10 of Applied Dynamics International, Ann Arbor, MI, a special-purpose peripheral processor for high-speed systems simulation, is programmed through a PDP-11/34 minicomputer and carries out digital simulations with analog hardware in the input/output loop (up to 256 channels). Analog signals from a control panel are being used now to activate or to disable valves and to trip pump drive motors or regulators without interrupting the simulation. An IBM personal computer with multicolor graphics capabilities and a CRT monitor are used to produce on-line labelled diagrams of selected plant parameters as functions of time

  5. Analyzing Music Services Positioning Through Qualitative Research

    Directory of Open Access Journals (Sweden)

    Manuel Cuadrado

    2015-12-01

    Full Text Available Information technologies have produced new ways of distributing and consuming music, mainly by youth, in relation to both goods and services. In the case of goods, there has been a dramatic shift from traditional ways of buying and listening to music to new digital platforms. There has also been an evolution in relation to music services. In this sense, live music concerts have been losing their audiences over the past few years, as have music radio stations, in favor of streaming platforms. Curious about this phenomenon, we conducted an exploratory research in order to analyze how all these services, both traditional and new ones were perceived. Specifically, we aimed to study youth´s assessment of the three most relevant music service categories: music radio stations, digital streaming platforms, and pop-rock music festivals. To do so, we used the projective technique of image association to gather information. The population of the study consisted of individuals between 18 and 25 years of age. Our results, after using content analysis, were poor due to spontaneous recall. Therefore, we duplicated the study, but in a more focus-oriented way. Information gathered this time allowed us not only to better know how all these organizations are positioned but also to obtain a list of descriptors to be used in a subsequent descriptive research study.

  6. Analyzing Design Heating Loads in Superinsulated Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Arena, Lois [Consortium for Advanced Residential Buildings, Norwalk, CT (United States)

    2015-06-16

    The U.S. Department of Energy’s Building America research team Consortium for Advanced Residential Buildings (CARB) worked with the EcoVillage cohousing community in Ithaca, New York, on the Third Residential EcoVillage Experience neighborhood. This communityscale project consists of 40 housing units—15 apartments and 25 single-family residences. Units range in size from 450 ft2 to 1,664 ft2 and cost from $80,000 for a studio apartment to $235,000 for a three- or four-bedroom single-family home. For the research component of this project, CARB analyzed current heating system sizing methods for superinsulated homes in cold climates to determine if changes in building load calculation methodology should be recommended. Actual heating energy use was monitored and compared to results from the Air Conditioning Contractors of America’s Manual J8 (MJ8) and the Passive House Planning Package software. Results from that research indicate that MJ8 significantly oversizes heating systems for superinsulated homes and that thermal inertia and internal gains should be considered for more accurate load calculations.

  7. Analyzing modified unimodular gravity via Lagrange multipliers

    Science.gov (United States)

    Sáez-Gómez, Diego

    2016-06-01

    The so-called unimodular version of general relativity is revisited. Unimodular gravity is constructed by fixing the determinant of the metric, which leads to the trace-free part of the equations instead of the usual Einstein field equations. Then a cosmological constant naturally arises as an integration constant. While unimodular gravity turns out to be equivalent to general relativity (GR) at the classical level, it provides important differences at the quantum level. Here we extend the unimodular constraint to some extensions of general relativity that have drawn a lot of attention over the last years—f (R ) gravity (or its scalar-tensor picture) and Gauss-Bonnet gravity. The corresponding unimodular version of such theories is constructed as well as the conformal transformation that relates the Einstein and Jordan frames for these nonminimally coupled theories. From the classical point of view, the unimodular versions of such extensions are completely equivalent to their originals, but an effective cosmological constant arises naturally, which may provide a richer description of the evolution of the Universe. Here we analyze the case of Starobisnky inflation and compare it with the original one.

  8. Analyzing sociodemographic factors amongst blood donors

    Directory of Open Access Journals (Sweden)

    Shenga Namgay

    2010-01-01

    Full Text Available Introduction: Blood transfusion is a fundamental and requisite part of any National Health Service for optimum management of emergency conditions like severe trauma shock and resuscitation with the optimum stock of its different components. The objective of the present study was to analyze the factors of knowledge of prospective blood donors that may influence their perception and awareness about blood donation. Materials and Methods: This population-based cross-sectional study was conducted at Gangtok in the state of Sikkim, India, on 300 subjects of the adult population selected by two-stage cluster sampling. The main outcome variables were the socioeconomic and demographic variables of knowledge of blood donation. By interview technique, using the pre-tested structured close-ended questionnaire, the principal investigator collected the data. Results: In our study population, 46% of the study population was found to have a high knowledge score. The knowledge about blood donation was found to be statistically significant with the occupational status and the education levels, both in the bivariate and in the multivariate analyses. Knowledge about blood donation was not significantly related to age, sex, marital status, religion, community status and per capita monthly family income. Conclusion: The study suggested that the perceptions toward voluntary blood donation could be influenced to a large extent by sociodemographic variables of knowledge among the general population.

  9. Artificial patinas analyzed with PIXE method

    International Nuclear Information System (INIS)

    Aiming at the restoration and conservation of the archaeological metallic objects, the artificial patinas can be used to simulate the natural patinas (corrosion products in metal and its alloys), permitting the characterization and corrosion mechanisms studies. The natural patinas formation is difficult to study because of the long corrosion production process in materials which take years to be formed. On the other hand the artificial patinas can be easily produced in a shorter time, moreover, they can be used as simulation of the corrosion process and in substitution of monuments and old art objects, damaged for some reason. In our study artificial patinas were produced over pellets of copper and bronze with sulfate, chloride and nitrate solutions and were analyzed with PIXE (Proton Induced X-Ray Emission) technique to supply qualitative and quantitative information of the corrosion elements. The quantitative PIXE analysis takes into account the incident ion beam absorption and the emergent X-ray of the sample, as well as the patina layer and the backing. The PIXE results have shown the presence of S, Cl and Fe and some other elements already known form the backings, such as Cu, Sn, etc. PIXE measurements were also realized in reference metallic materials. (author)

  10. Analyzing personalized policies for online biometric verification.

    Directory of Open Access Journals (Sweden)

    Apaar Sadhwani

    Full Text Available Motivated by India's nationwide biometric program for social inclusion, we analyze verification (i.e., one-to-one matching in the case where we possess similarity scores for 10 fingerprints and two irises between a resident's biometric images at enrollment and his biometric images during his first verification. At subsequent verifications, we allow individualized strategies based on these 12 scores: we acquire a subset of the 12 images, get new scores for this subset that quantify the similarity to the corresponding enrollment images, and use the likelihood ratio (i.e., the likelihood of observing these scores if the resident is genuine divided by the corresponding likelihood if the resident is an imposter to decide whether a resident is genuine or an imposter. We also consider two-stage policies, where additional images are acquired in a second stage if the first-stage results are inconclusive. Using performance data from India's program, we develop a new probabilistic model for the joint distribution of the 12 similarity scores and find near-optimal individualized strategies that minimize the false reject rate (FRR subject to constraints on the false accept rate (FAR and mean verification delay for each resident. Our individualized policies achieve the same FRR as a policy that acquires (and optimally fuses 12 biometrics for each resident, which represents a five (four, respectively log reduction in FRR relative to fingerprint (iris, respectively policies previously proposed for India's biometric program. The mean delay is [Formula: see text] sec for our proposed policy, compared to 30 sec for a policy that acquires one fingerprint and 107 sec for a policy that acquires all 12 biometrics. This policy acquires iris scans from 32-41% of residents (depending on the FAR and acquires an average of 1.3 fingerprints per resident.

  11. Climate Model Diagnostic Analyzer Web Service System

    Science.gov (United States)

    Lee, S.; Pan, L.; Zhai, C.; Tang, B.; Kubar, T. L.; Li, J.; Zhang, J.; Wang, W.

    2015-12-01

    Both the National Research Council Decadal Survey and the latest Intergovernmental Panel on Climate Change Assessment Report stressed the need for the comprehensive and innovative evaluation of climate models with the synergistic use of global satellite observations in order to improve our weather and climate simulation and prediction capabilities. The abundance of satellite observations for fundamental climate parameters and the availability of coordinated model outputs from CMIP5 for the same parameters offer a great opportunity to understand and diagnose model biases in climate models. In addition, the Obs4MIPs efforts have created several key global observational datasets that are readily usable for model evaluations. However, a model diagnostic evaluation process requires physics-based multi-variable comparisons that typically involve large-volume and heterogeneous datasets, making them both computationally- and data-intensive. In response, we have developed a novel methodology to diagnose model biases in contemporary climate models and implementing the methodology as a web-service based, cloud-enabled, provenance-supported climate-model evaluation system. The evaluation system is named Climate Model Diagnostic Analyzer (CMDA), which is the product of the research and technology development investments of several current and past NASA ROSES programs. The current technologies and infrastructure of CMDA are designed and selected to address several technical challenges that the Earth science modeling and model analysis community faces in evaluating and diagnosing climate models. In particular, we have three key technology components: (1) diagnostic analysis methodology; (2) web-service based, cloud-enabled technology; (3) provenance-supported technology. The diagnostic analysis methodology includes random forest feature importance ranking, conditional probability distribution function, conditional sampling, and time-lagged correlation map. We have implemented the

  12. Analyzing wildfire exposure on Sardinia, Italy

    Science.gov (United States)

    Salis, Michele; Ager, Alan A.; Arca, Bachisio; Finney, Mark A.; Alcasena, Fermin; Bacciu, Valentina; Duce, Pierpaolo; Munoz Lozano, Olga; Spano, Donatella

    2014-05-01

    We used simulation modeling based on the minimum travel time algorithm (MTT) to analyze wildfire exposure of key ecological, social and economic features on Sardinia, Italy. Sardinia is the second largest island of the Mediterranean Basin, and in the last fifty years experienced large and dramatic wildfires, which caused losses and threatened urban interfaces, forests and natural areas, and agricultural productions. Historical fires and environmental data for the period 1995-2009 were used as input to estimate fine scale burn probability, conditional flame length, and potential fire size in the study area. With this purpose, we simulated 100,000 wildfire events within the study area, randomly drawing from the observed frequency distribution of burn periods and wind directions for each fire. Estimates of burn probability, excluding non-burnable fuels, ranged from 0 to 1.92x10-3, with a mean value of 6.48x10-5. Overall, the outputs provided a quantitative assessment of wildfire exposure at the landscape scale and captured landscape properties of wildfire exposure. We then examined how the exposure profiles varied among and within selected features and assets located on the island. Spatial variation in modeled outputs resulted in a strong effect of fuel models, coupled with slope and weather. In particular, the combined effect of Mediterranean maquis, woodland areas and complex topography on flame length was relevant, mainly in north-east Sardinia, whereas areas with herbaceous fuels and flat areas were in general characterized by lower fire intensity but higher burn probability. The simulation modeling proposed in this work provides a quantitative approach to inform wildfire risk management activities, and represents one of the first applications of burn probability modeling to capture fire risk and exposure profiles in the Mediterranean basin.

  13. A New Statistic for Analyzing Baryon Acoustic Oscillations

    CERN Document Server

    Xu, X; Padmanabhan, N; Eisenstein, D; Eckel, J; Mehta, K; Metchnik, M; Pinto, P; Seo, H -J

    2010-01-01

    We introduce a new statistic omega_l for measuring and analyzing large-scale structure and particularly the baryon acoustic oscillations. omega_l is a band-filtered, configuration space statistic that is easily implemented and has advantages over the traditional power spectrum and correlation function estimators. Unlike these estimators, omega_l can localize most of the acoustic information into a single dip at the acoustic scale while also avoiding sensitivity to the poorly constrained large scale power (i.e., the integral constraint) through the use of a localized and compensated filter. It is also sensitive to anisotropic clustering through pair counting and does not require any binning. We measure the shift in the acoustic peak due to nonlinear effects using the monopole omega_0 derived from subsampled dark matter catalogues as well as from mock galaxy catalogues created via halo occupation distribution (HOD) modeling. All of these are drawn from 44 realizations of 1024^3 particle dark matter simulations ...

  14. Atomic power's powered atomiser

    International Nuclear Information System (INIS)

    As an extension of its traditional activities the United Kingdom Atomic Energy Authority (UKAEA) has developed a range of products and services. So far one of its most successful ventures has been the licensing of power fluidics technology in the hvac (heating, ventilation and air conditioning) market. Power Fluidics is the control of liquid or gas flows without the use of any moving parts. The UKAEA has developed the vortex amplifier, a control device, which has many potential applications, in which the process flow is throttled and turned down as the control flow is increased. The bistable flow diverter in which a coanda effect diverts the flow down one of two outlets has possible uses in the water industry as well. Another development is a device for controlling fluid droplet size in which a bistable converter has a feedback loop which ensures continuous switching of the flow. By opposing the nozzle outlets, the alternating flows collide in a controlled manner and droplet size can be controlled. (U.K.)

  15. Climate Model Diagnostic Analyzer Web Service System

    Science.gov (United States)

    Lee, S.; Pan, L.; Zhai, C.; Tang, B.; Jiang, J. H.

    2013-12-01

    The latest Intergovernmental Panel on Climate Change (IPCC) Fourth Assessment Report stressed the need for the comprehensive and innovative evaluation of climate models with newly available global observations. The traditional approach to climate model evaluation, which compares a single parameter at a time, identifies symptomatic model biases and errors but fails to diagnose the model problems. The model diagnosis process requires physics-based multi-variable comparisons that typically involve large-volume and heterogeneous datasets, making them both computationally- and data-intensive. To address these challenges, we are developing a parallel, distributed web-service system that enables the physics-based multi-variable model performance evaluations and diagnoses through the comprehensive and synergistic use of multiple observational data, reanalysis data, and model outputs. We have developed a methodology to transform an existing science application code into a web service using a Python wrapper interface and Python web service frameworks (i.e., Flask, Gunicorn, and Tornado). The web-service system, called Climate Model Diagnostic Analyzer (CMDA), currently supports (1) all the datasets from Obs4MIPs and a few ocean datasets from NOAA and Argo, which can serve as observation-based reference data for model evaluation and (2) many of CMIP5 model outputs covering a broad range of atmosphere, ocean, and land variables from the CMIP5 specific historical runs and AMIP runs. Analysis capabilities currently supported by CMDA are (1) the calculation of annual and seasonal means of physical variables, (2) the calculation of time evolution of the means in any specified geographical region, (3) the calculation of correlation between two variables, and (4) the calculation of difference between two variables. A web user interface is chosen for CMDA because it not only lowers the learning curve and removes the adoption barrier of the tool but also enables instantaneous use

  16. Climate Model Diagnostic Analyzer Web Service System

    Science.gov (United States)

    Lee, S.; Pan, L.; Zhai, C.; Tang, B.; Jiang, J. H.

    2014-12-01

    We have developed a cloud-enabled web-service system that empowers physics-based, multi-variable model performance evaluations and diagnoses through the comprehensive and synergistic use of multiple observational data, reanalysis data, and model outputs. We have developed a methodology to transform an existing science application code into a web service using a Python wrapper interface and Python web service frameworks. The web-service system, called Climate Model Diagnostic Analyzer (CMDA), currently supports (1) all the observational datasets from Obs4MIPs and a few ocean datasets from NOAA and Argo, which can serve as observation-based reference data for model evaluation, (2) many of CMIP5 model outputs covering a broad range of atmosphere, ocean, and land variables from the CMIP5 specific historical runs and AMIP runs, and (3) ECMWF reanalysis outputs for several environmental variables in order to supplement observational datasets. Analysis capabilities currently supported by CMDA are (1) the calculation of annual and seasonal means of physical variables, (2) the calculation of time evolution of the means in any specified geographical region, (3) the calculation of correlation between two variables, (4) the calculation of difference between two variables, and (5) the conditional sampling of one physical variable with respect to another variable. A web user interface is chosen for CMDA because it not only lowers the learning curve and removes the adoption barrier of the tool but also enables instantaneous use, avoiding the hassle of local software installation and environment incompatibility. CMDA will be used as an educational tool for the summer school organized by JPL's Center for Climate Science in 2014. In order to support 30+ simultaneous users during the school, we have deployed CMDA to the Amazon cloud environment. The cloud-enabled CMDA will provide each student with a virtual machine while the user interaction with the system will remain the same

  17. Analyzing milestoning networks for molecular kinetics: Definitions, algorithms, and examples

    Science.gov (United States)

    Viswanath, Shruthi; Kreuzer, Steven M.; Cardenas, Alfredo E.; Elber, Ron

    2013-11-01

    Network representations are becoming increasingly popular for analyzing kinetic data from techniques like Milestoning, Markov State Models, and Transition Path Theory. Mapping continuous phase space trajectories into a relatively small number of discrete states helps in visualization of the data and in dissecting complex dynamics to concrete mechanisms. However, not only are molecular networks derived from molecular dynamics simulations growing in number, they are also getting increasingly complex, owing partly to the growth in computer power that allows us to generate longer and better converged trajectories. The increased complexity of the networks makes simple interpretation and qualitative insight of the molecular systems more difficult to achieve. In this paper, we focus on various network representations of kinetic data and algorithms to identify important edges and pathways in these networks. The kinetic data can be local and partial (such as the value of rate coefficients between states) or an exact solution to kinetic equations for the entire system (such as the stationary flux between vertices). In particular, we focus on the Milestoning method that provides fluxes as the main output. We proposed Global Maximum Weight Pathways as a useful tool for analyzing molecular mechanism in Milestoning networks. A closely related definition was made in the context of Transition Path Theory. We consider three algorithms to find Global Maximum Weight Pathways: Recursive Dijkstra's, Edge-Elimination, and Edge-List Bisection. The asymptotic efficiency of the algorithms is analyzed and numerical tests on finite networks show that Edge-List Bisection and Recursive Dijkstra's algorithms are most efficient for sparse and dense networks, respectively. Pathways are illustrated for two examples: helix unfolding and membrane permeation. Finally, we illustrate that networks based on local kinetic information can lead to incorrect interpretation of molecular mechanisms.

  18. Power quality assessment

    International Nuclear Information System (INIS)

    The electrical power systems are exposed to different types of power quality disturbances problems. Assessment of power quality is necessary for maintaining accurate operation of sensitive equipment's especially for nuclear installations, it also ensures that unnecessary energy losses in a power system are kept at a minimum which lead to more profits. With advanced in technology growing of industrial / commercial facilities in many region. Power quality problems have been a major concern among engineers; particularly in an industrial environment, where there are many large-scale type of equipment. Thus, it would be useful to investigate and mitigate the power quality problems. Assessment of Power quality requires the identification of any anomalous behavior on a power system, which adversely affects the normal operation of electrical or electronic equipment. The choice of monitoring equipment in a survey is also important to ascertain a solution to these power quality problems. A power quality assessment involves gathering data resources; analyzing the data (with reference to power quality standards); then, if problems exist, recommendation of mitigation techniques must be considered. The main objective of the present work is to investigate and mitigate of power quality problems in nuclear installations. Normally electrical power is supplied to the installations via two sources to keep good reliability. Each source is designed to carry the full load. The Assessment of power quality was performed at the nuclear installations for both sources at different operation conditions. The thesis begins with a discussion of power quality definitions and the results of previous studies in power quality monitoring. The assessment determines that one source of electricity was deemed to have relatively good power quality; there were several disturbances, which exceeded the thresholds. Among of them are fifth harmonic, voltage swell, overvoltage and flicker. While the second

  19. HMR Log Analyzer: Analyze Web Application Logs Over Hadoop MapReduce

    OpenAIRE

    Sayalee Narkhede; Tripti Baraskar

    2013-01-01

    In today’s Internet world, log file analysis is becoming a necessary task for analyzing the customer’sbehavior in order to improve advertising and sales as well as for datasets like environment, medical,banking system it is important to analyze the log data to get required knowledge from it. Web mining is theprocess of discovering the knowledge from the web data. Log files are getting generated very fast at therate of 1-10 Mb/s per machine, a single data center can generate tens of terabytes ...

  20. Resonant High Power Combiners

    CERN Document Server

    Langlois, Michel; Peillex-Delphe, Guy

    2005-01-01

    Particle accelerators need radio frequency sources. Above 300 MHz, the amplifiers mostly used high power klystrons developed for this sole purpose. As for military equipment, users are drawn to buy "off the shelf" components rather than dedicated devices. IOTs have replaced most klystrons in TV transmitters and find their way in particle accelerators. They are less bulky, easier to replace, more efficient at reduced power. They are also far less powerful. What is the benefit of very compact sources if huge 3 dB couplers are needed to combine the power? To alleviate this drawback, we investigated a resonant combiner, operating in TM010 mode, able to combine 3 to 5 IOTs. Our IOTs being able to deliver 80 kW C.W. apiece, combined power would reach 400 kW minus the minor insertion loss. Values for matching and insertion loss are given. The behavior of the system in case of IOT failure is analyzed.

  1. ICAN - INTEGRATED COMPOSITE ANALYZER (IBM PC VERSION)

    Science.gov (United States)

    Murthy, P. L.

    1994-01-01

    The Integrated Composite Analyzer (ICAN) is a computer program designed to carry out a comprehensive linear analysis of multilayered fiber composites. The analysis contains the essential features required to effectively design structural components made from fiber composites. ICAN includes the micromechanical design features of the Intraply Hybrid Composite Design (INHYD) program to predict ply level hygral, thermal, and mechanical properties. The laminate analysis features of the Multilayered Filamentary Composite Analysis (MFCA) program are included to account for interply layer effects. ICAN integrates these and additional features to provide a comprehensive analysis capability for composite structures. Additional features unique to ICAN include the following: 1) ply stress-strain influence coefficients, 2) microstresses and microstrain influence coefficients, 3) concentration factors around a circular hole, 4) calculation of probable delamination locations around a circular hole, 5) Poisson's ratio mismatch details near a straight edge, 6) free-edge stresses, 7) material card input for finite element analysis using NASTRAN (available separately from COSMIC) or MARC, 8) failure loads based on maximum stress criterion, and laminate failure stresses based on first-ply failures and fiber breakage criteria, 9) transverse shear stresses, normal and interlaminar stresses, and 10) durability/fatigue type analyses for thermal as well as mechanical cyclic loads. The code can currently assess degradation due to mechanical and thermal cyclic loads with or without a defect. ICAN includes a dedicated data bank of constituent material properties, and allows the user to build a database of material properties of commonly used fibers and matrices so the user need only specify code names for constituents. Input to ICAN includes constituent material properties (or code names), factors reflecting the fabrication process, and composite geometry. ICAN performs micromechanics

  2. ICAN - INTEGRATED COMPOSITE ANALYZER (IBM 370 VERSION)

    Science.gov (United States)

    Murthy, P. L.

    1994-01-01

    The Integrated Composite Analyzer (ICAN) is a computer program designed to carry out a comprehensive linear analysis of multilayered fiber composites. The analysis contains the essential features required to effectively design structural components made from fiber composites. ICAN includes the micromechanical design features of the Intraply Hybrid Composite Design (INHYD) program to predict ply level hygral, thermal, and mechanical properties. The laminate analysis features of the Multilayered Filamentary Composite Analysis (MFCA) program are included to account for interply layer effects. ICAN integrates these and additional features to provide a comprehensive analysis capability for composite structures. Additional features unique to ICAN include the following: 1) ply stress-strain influence coefficients, 2) microstresses and microstrain influence coefficients, 3) concentration factors around a circular hole, 4) calculation of probable delamination locations around a circular hole, 5) Poisson's ratio mismatch details near a straight edge, 6) free-edge stresses, 7) material card input for finite element analysis using NASTRAN (available separately from COSMIC) or MARC, 8) failure loads based on maximum stress criterion, and laminate failure stresses based on first-ply failures and fiber breakage criteria, 9) transverse shear stresses, normal and interlaminar stresses, and 10) durability/fatigue type analyses for thermal as well as mechanical cyclic loads. The code can currently assess degradation due to mechanical and thermal cyclic loads with or without a defect. ICAN includes a dedicated data bank of constituent material properties, and allows the user to build a database of material properties of commonly used fibers and matrices so the user need only specify code names for constituents. Input to ICAN includes constituent material properties (or code names), factors reflecting the fabrication process, and composite geometry. ICAN performs micromechanics

  3. Analyzers Measure Greenhouse Gases, Airborne Pollutants

    Science.gov (United States)

    2012-01-01

    In complete darkness, a NASA observatory waits. When an eruption of boiling water billows from a nearby crack in the ground, the observatory s sensors seek particles in the fluid, measure shifts in carbon isotopes, and analyze samples for biological signatures. NASA has landed the observatory in this remote location, far removed from air and sunlight, to find life unlike any that scientists have ever seen. It might sound like a scene from a distant planet, but this NASA mission is actually exploring an ocean floor right here on Earth. NASA established a formal exobiology program in 1960, which expanded into the present-day Astrobiology Program. The program, which celebrated its 50th anniversary in 2010, not only explores the possibility of life elsewhere in the universe, but also examines how life begins and evolves, and what the future may hold for life on Earth and other planets. Answers to these questions may be found not only by launching rockets skyward, but by sending probes in the opposite direction. Research here on Earth can revise prevailing concepts of life and biochemistry and point to the possibilities for life on other planets, as was demonstrated in December 2010, when NASA researchers discovered microbes in Mono Lake in California that subsist and reproduce using arsenic, a toxic chemical. The Mono Lake discovery may be the first of many that could reveal possible models for extraterrestrial life. One primary area of interest for NASA astrobiologists lies with the hydrothermal vents on the ocean floor. These vents expel jets of water heated and enriched with chemicals from off-gassing magma below the Earth s crust. Also potentially within the vents: microbes that, like the Mono Lake microorganisms, defy the common characteristics of life on Earth. Basically all organisms on our planet generate energy through the Krebs Cycle, explains Mike Flynn, research scientist at NASA s Ames Research Center. This metabolic process breaks down sugars for energy

  4. Using Simulation to Analyze Acoustic Environments

    Science.gov (United States)

    Wood, Eric J.

    2016-01-01

    One of the main projects that was worked on this semester was creating an acoustic model for the Advanced Space Suit in Comsol Multiphysics. The geometry tools built into the software were used to create an accurate model of the helmet and upper torso of the suit. After running the simulation, plots of the sound pressure level within the suit were produced, as seen below in Figure 1. These plots show significant nulls which should be avoided when placing microphones inside the suit. In the future, this model can be easily adapted to changes in the suit design to determine optimal microphone placements and other acoustic properties. Another major project was creating an acoustic diverter that will potentially be used to route audio into the Space Station's Node 1. The concept of the project was to create geometry to divert sound from a neighboring module, the US Lab, into Node 1. By doing this, no new audio equipment would need to be installed in Node 1. After creating an initial design for the diverter, analysis was performed in Comsol in order to determine how changes in geometry would affect acoustic performance, as shown in Figure 2. These results were used to produce a physical prototype diverter on a 3D printer. With the physical prototype, testing was conducted in an anechoic chamber to determine the true effectiveness of the design, as seen in Figure 3. The results from this testing have been compared to the Comsol simulation results to analyze how closely the Comsol results are to real-world performance. While the Comsol results do not seem to closely resemble the real world performance, this testing has provided valuable insight into how much trust can be placed in the results of Comsol simulations. A final project that was worked on during this tour was the Audio Interface Unit (AIU) design for the Orion program. The AIU is a small device that will be used for as an audio communication device both during launch and on-orbit. The unit will have functions

  5. Wind power in power systems

    CERN Document Server

    Ackermann, Thomas

    2012-01-01

    The second edition of the highly acclaimed Wind Power in Power Systems has been thoroughly revised and expanded to reflect the latest challenges associated with increasing wind power penetration levels. Since its first release, practical experiences with high wind power penetration levels have significantly increased. This book presents an overview of the lessons learned in integrating wind power into power systems and provides an outlook of the relevant issues and solutions to allow even higher wind power penetration levels. This includes the development of standard wind turbine sim

  6. Power Electronics

    DEFF Research Database (Denmark)

    Iov, Florin; Ciobotaru, Mihai; Blaabjerg, Frede;

    2008-01-01

    emerging renewable energy sources, wind energy, which by means of power electronics are changing from being a minor energy source to be acting as an important power source in the energy system. Power electronics is the enabling technology and the presentation will cover the development in wind turbine...... energy at the end-user should also be set up. Deregulation of energy has in the past lowered the investment in larger power plants, which means the need for new electrical power sources will be high in the near future. Two major technologies will play important roles to solve the future problems. One...... is to change the electrical power production sources from the conventional, fossil (and short term) based energy sources to renewable energy resources. The other is to use high efficient power electronics in power generation, power transmission/distribution and end-user application. This paper discuss the most...

  7. Errors in the measurement of non-Gaussian noise spectra using rf spectrum analyzers

    International Nuclear Information System (INIS)

    We discuss the nature of errors which may occur when the spectra of random signals not obeying Gaussian statistics are measured with typical rf spectrum analyzers. These errors depend on both the noise statistics and the process used to detect the random signal after it has been passed through a narrow bandpass filter within the spectrum analyzer. In general, for random signals not obeying Gaussian statistics, the output of the bandpass filter must be measured with a square law detector if the resulting measurement is to be strictly proportional to the power spectrum of the input signal. We compare measurements of the power spectra of non-Gaussian noise using a commerical spectrum analyzer with its resident envelope detector, with measurements by the same analyzer fitted with a square law detector. Differences of about 5% were observed

  8. The earthquake security of the Paks Nuclear Power Plant

    International Nuclear Information System (INIS)

    The seismic safety of Paks Nuclear Power Plant is analyzed. Assessment of earthquake risk has been done at the site of the plant, and seismic resistance of the nuclear power plant is analyzed together. (TRA)

  9. Tiny Integrated Network Analyzer for Noninvasive Measurements of Electrically Small Antennas

    DEFF Research Database (Denmark)

    Buskgaard, Emil Feldborg; Krøyer, Ben; Tatomirescu, Alexandru;

    2016-01-01

    system. The tiny integrated network analyzer is a stand-alone Arduino-based measurement system that utilizes the transmit signal of the system under test as its reference. It features a power meter with triggering ability, on-board memory, universal serial bus, and easy extendibility with general...... network analysis. With the advances in software-defined radio, we can expect much more flexible and advanced integrated network analyzers in the coming years....

  10. Design of multi-channel amplitude analyzer base on LonWorks

    International Nuclear Information System (INIS)

    The paper introduces the multi-channel analyzer which adopts LonWorks technology. The system detects the pulse peak by hardware circuits and controls data acquisition and network communication by Micro Controller and Unit and Neuron chip. SCM is programmed by Keil C51; the communication between SCM and nerve cell is realized by Neron C language, and the computer program is written by VB language. Test results show that this analyzer is with fast conversion speed and low power consumption. (authors)

  11. A design of portable energy dispersive X-ray fluorescence analyzer

    International Nuclear Information System (INIS)

    A portable energy dispersive X-ray fluorescence analyzer (EDXRF) is designed. Excitation source is a small-caliber X-ray tube with Mo target. High-voltage power supply and filament supply is designed based on inverter technology. Semiconductor detectors is electric refrigerated, the qualities of the analyzer and the energy calibration curve are studied by the energy spectrum measurements for Cu, Zn, Ni, Pb, and the best range of elemental analysis is given by the theoretical analysis. (authors)

  12. Analyzing social experiments as implemented: Evidence from the HighScope Perry Preschool Program

    OpenAIRE

    Heckman, James; Moon, Seong Hyeok; Pinto, Rodrigo; Savelyev, Peter; Yavitz, Adam

    2010-01-01

    Social experiments are powerful sources of information about the effectiveness of interventions. In practice, initial randomization plans are almost always compromised. Multiple hypotheses are frequently tested. "Significant" effects are often reported with p-values that do not account for preliminary screening from a large candidate pool of possible effects. This paper develops tools for analyzing data from experiments as they are actually implemented. We apply these tools to analyze the inf...

  13. Noise and analyzer-crystal angular position analysis for analyzer-based phase-contrast imaging

    International Nuclear Information System (INIS)

    The analyzer-based phase-contrast x-ray imaging (ABI) method is emerging as a potential alternative to conventional radiography. Like many of the modern imaging techniques, ABI is a computed imaging method (meaning that images are calculated from raw data). ABI can simultaneously generate a number of planar parametric images containing information about absorption, refraction, and scattering properties of an object. These images are estimated from raw data acquired by measuring (sampling) the angular intensity profile of the x-ray beam passed through the object at different angular positions of the analyzer crystal. The noise in the estimated ABI parametric images depends upon imaging conditions like the source intensity (flux), measurements angular positions, object properties, and the estimation method. In this paper, we use the Cramér–Rao lower bound (CRLB) to quantify the noise properties in parametric images and to investigate the effect of source intensity, different analyzer-crystal angular positions and object properties on this bound, assuming a fixed radiation dose delivered to an object. The CRLB is the minimum bound for the variance of an unbiased estimator and defines the best noise performance that one can obtain regardless of which estimation method is used to estimate ABI parametric images. The main result of this paper is that the variance (hence the noise) in parametric images is directly proportional to the source intensity and only a limited number of analyzer-crystal angular measurements (eleven for uniform and three for optimal non-uniform) are required to get the best parametric images. The following angular measurements only spread the total dose to the measurements without improving or worsening CRLB, but the added measurements may improve parametric images by reducing estimation bias. Next, using CRLB we evaluate the multiple-image radiography, diffraction enhanced imaging and scatter diffraction enhanced imaging estimation techniques

  14. Thromboelastography platelet mapping in healthy dogs using 1 analyzer versus 2 analyzers

    OpenAIRE

    Blois, Shauna L.; Banerjee, Amrita; Wood, R. Darren; Park, Fiona M.

    2013-01-01

    The objective of this study was to describe the results of thromboelastography platelet mapping (TEG-PM) carried out using 2 techniques in 20 healthy dogs. Maximum amplitudes (MA) generated by thrombin (MAthrombin), fibrin (MAfibrin), adenosine diphosphate (ADP) receptor activity (MAADP), and thromboxane A2 (TxA2) receptor activity (stimulated by arachidonic acid, MAAA) were recorded. Thromboelastography platelet mapping was carried out according to the manufacturer’s guidelines (2-analyzer t...

  15. Noise and Analyzer-Crystal Angular Position Analysis for Analyzer-Based Phase-Contrast Imaging

    OpenAIRE

    Majidi, Keivan; Li, Jun; Muehleman, Carol; Brankov, Jovan G.

    2014-01-01

    The analyzer-based phase-contrast X-ray imaging (ABI) method is emerging as a potential alternative to conventional radiography. Like many of the modern imaging techniques, ABI is a computed imaging method (meaning that images are calculated from raw data). ABI can simultaneously generate a number of planar parametric images containing information about absorption, refraction, and scattering properties of an object. These images are estimated from raw data acquired by measuring (sampling) the...

  16. Smile Analyzer: A Software Package for Analyzing the Characteristics of the Speech and Smile

    OpenAIRE

    Farzin Heravi; Roozbeh Rashed; Leila Raziee

    2013-01-01

    Taking into account the factors related to lip-tooth relationships in orthodontic diagnosis and treatment planning is of prime importance. Manual quantitative analysis of facial parameters on photographs during smile and speech is a difficult and time-consuming job. Since there is no comprehensive and user-friendly software package, we developed a software program called "Smile Analyzer" in the Department of Orthodontics of Mashhad Faculty of Dentistry for measuring the parameters related to ...

  17. Fractals in Power Reactor Noise

    International Nuclear Information System (INIS)

    In this work the non- lineal dynamic problem of power reactor is analyzed using classic concepts of fractal analysis as: attractors, Hausdorff-Besikovics dimension, phase space, etc. A new non-linear problem is also analyzed: the discrimination of chaotic signals from random neutron noise signals and processing for diagnosis purposes. The advantages of a fractal analysis approach in the power reactor noise are commented in details

  18. Electric Power

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ China Council for the Promotion of International Trade Electric Power Industry Office (CCPIT Electric Power), one of the pro-fessional industrial branches of China Council for the Promotion of International Trade (CCPIT), was established in 2006.

  19. Analyze the economic and environmental viability in distributed generation of electric power from renewable sources

    International Nuclear Information System (INIS)

    This paper brings a brief of economical and social environmental analysis about distributed electric's energy generation, based on a comparison to centralized generation. The motivation of the proposed analysis has its origin on a reflection about politics and scheming directed to Brazilian's energy sector. This study has renewable energy resources as setting, represented for Belo Monte generation's plant and undertaking registered on the Reservation's Energy Auction 2010. The study took into account economics and technical aspects, whereas the viability analysis was formed from benefits got from different forms of electric's generation. The conclusions of this shows that distributed electric's energy generation may have economics and socio environment benefits over centralized generation. (author)

  20. Measurement of the analyzing power in pp elastic scattering in the peak CNI region at RHIC

    OpenAIRE

    Okada, H.; Alekseev, I. G.; Bravar, A; Bunce, G.; Dhawan, S.; Gill, R; Haeberli, W.; Jinnouchi, O.; Khodinov, A.; Kponou, A.; Makdisi, Y.; Meng, W; Nass, A.; Saito, N; Spinka, H.

    2005-01-01

    We report the first measurements of the A_N absolute value and shape in the -t range from 0.0015 to 0.010GeV/c^2 with a precision better than 0.005 for each A_N data point using a polarized atomic hydrogen gas jet target and the 100 GeV RHIC proton beam.

  1. Tensor analyzing power in pd backward scattering at GeV energies

    International Nuclear Information System (INIS)

    Measurements are reported of the sperical tensor component t20 for 1.0-, 0.0-, and 0.4-GeV equivalent proton bombarding energies for elastic p-d scattering between 1550--1750. They are very close to zero in disagreement with the predictigns of nucleon exchange models, including the Kerman-Kisslanger model with F* components in the deuteron wave functign. The experiment was performed with a vector- and tensor-polarized deuteron beam scattered from a liquid hydrogen target

  2. Migration of the UNIX Application for eFAST CANDU Nuclear Power Plant Analyzer

    International Nuclear Information System (INIS)

    Since the mid 1980s, corporate data centers have been moving away from mainframes running dedicated operating systems to mini-computers, often using one or other of the myriad flavors of UNIX. At the same time, the users' experience of these systems has, in many cases, stayed the same, involving text-based interaction with dumb terminals or a terminal-emulation session on a Personal Computer. More recently, IT managers have questioned this approach, and have been looking at changes in the UNIX marketplace and the increasing expense of being tied in to single-vendor software and hardware solutions. The growth of Linux as a lightweight version of UNIX has fueled this interest, raising the number of organizations that are considering a migration to alternative platforms. The various implementations of the UNIX operating system have served industry well, as witnessed by the very large base both of installed systems and large-scale applications installed on those systems. However, there are increasing signs of dissatisfaction with expensive, often proprietary solutions and a growing sense that perhaps the concept of 'big iron' has had its day in the same way as it has for most of the mainframes of the type portrayed in 1970s science fiction films. One of the most extraordinary and unexpected successes of the Intel PC architecture is the extent to which this basic framework has been extended to encompass very large server and data center environments. Large-scale hosting companies are now offering enterprise level services to multiple client companies at availability levels of over 99.99 percent on what are simply racks of relatively cheap PCs. Technologies such as clustering, Network Load Balancing, and Component Load Balancing enable the personal computer to take on and match the levels of throughput, availability, and reliability of all but the most expensive 'big iron' solutions and the supercomputers

  3. Nuclear power constructions

    International Nuclear Information System (INIS)

    The feasibility study and the project design and their role in the process of nuclear power plant construction are analyzed in detail. From the point of view of systems aspects of scientific management, the nuclear power plant is considered to be an element of the power generation and transmission system as well as an intersection of capital investment, scientific and technical development and project designing. Foreign experience is summed up with the planning, designing and building of nuclear power plants. Attention is centred to the feasibility study and project design stages of nuclear power plant construction in the CSSR. The questions are discussed of capital investment, territorial planning activities, pre-project and project documentation; a survey is presented of legislative provisions involving the project design and capital investment spheres. Briefly outlined are topics for further rationalization of feasibility studies, such as standardization and complex project designs of WWER type nuclear power plants, the introduction of data processing in capital investment provision of WWER type nuclear power plants, and international scientific and technical cooperation including the establishment of a international consultancy centre for the designing and methodology of controlling the building, repairs, reconstruction and the decommissioning of WWER type nuclear power plants. (Z.M.). 81 figs., 2 tabs., 12 refs

  4. Reinventing the Solar Power Satellite

    Science.gov (United States)

    Landis, Geoffrey A.

    2004-01-01

    The selling price of electrical power varies with time. The economic viability of space solar power is maximum if the power can be sold at peak power rates, instead of baseline rate. Price and demand of electricity was examined from spot-market data from four example markets: New England, New York City, suburban New York, and California. The data was averaged to show the average price and demand for power as a function of time of day and time of year. Demand varies roughly by a factor of two between the early-morning minimum demand, and the afternoon maximum; both the amount of peak power, and the location of the peak, depends significantly on the location and the weather. The demand curves were compared to the availability curves for solar energy and for tracking and non-tracking satellite solar power systems in order to compare the market value of terrestrial and solar electrical power. In part 2, new designs for a space solar power (SSP) system were analyzed to provide electrical power to Earth for economically competitive rates. The approach was to look at innovative power architectures to more practical approaches to space solar power. A significant barrier is the initial investment required before the first power is returned. Three new concepts for solar power satellites were invented and analyzed: a solar power satellite in the Earth-Sun L2 point, a geosynchronous no-moving parts solar power satellite, and a nontracking geosynchronous solar power satellite with integral phased array. The integral-array satellite had several advantages, including an initial investment cost approximately eight times lower than the conventional design.

  5. Power marketing

    International Nuclear Information System (INIS)

    One of the most significant developments in the US electric power industry in recent years has been the phenomenal growth of power marketing. What was barely a blimp on the radar screen in 1992 has turned out to be a jumbo jet. This article explains what is power marketing who are power marketers, what role play these players and what will be their longer-term impact on the traditional industry

  6. Nuclear power

    International Nuclear Information System (INIS)

    The subject is covered in chapters entitled: nuclear power certainties and doubts; nuclear power in the Western World to 2000; the frequency of core meltdown accidents; hidden costs of the accident at Three Mile Island; costs of nuclear accidents - implications for reactor choice; defining the risks of nuclear power; the uncertain economics of a nuclear power program; the economics of enabling decisions (Sizewell B as an enabling decision); trade in nuclear electricity; some pointers to the future. (U.K.)

  7. A novel method to analyze damping effect of VSC based FACTS

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A novel method to analyze the damping effect of the VSC based FACTS(VBF) device is proposed,which is developed on the basis of the well-known equalarea criterion and small-disturbance analysis of power system oscillations.By use of the proposed method,two conclusions are obtained for study of the damping effect of the VBF.The research results clearly show the contribution of the VBF control to the damping of power system oscillations.Simulation results of an example power system are used to verify the effectiveness of the proposed method.

  8. A novel method to analyze damping effect of VSC based FACTS

    Institute of Scientific and Technical Information of China (English)

    DU WenJuan; WANG HaiFeng; CHENG ShiJie

    2008-01-01

    A novel method to analyze the damping effect of the VSC based FACTS (VBF) de-vice is proposed, which is developed on the basis of the well-known equal-area criterion and small-disturbance analysis of power system oscillations. By use of the proposed method, two conclusions are obtained for study of the damping effect of the VBF. The research results clearly show the contribution of the VBF control to thedamping of power system oscillations. Simulation results of an example power system are used to verify the effectiveness of the proposed method.

  9. A Big Data Approach to Analyzing Market Volatility

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Kesheng; Bethel, E. Wes; Gu, Ming; Leinweber, David; Ruebel, Oliver

    2013-06-05

    Understanding the microstructure of the financial market requires the processing of a vast amount of data related to individual trades, and sometimes even multiple levels of quotes. Analyzing such a large volume of data requires tremendous computing power that is not easily available to financial academics and regulators. Fortunately, public funded High Performance Computing (HPC) power is widely available at the National Laboratories in the US. In this paper we demonstrate that the HPC resource and the techniques for data-intensive sciences can be used to greatly accelerate the computation of an early warning indicator called Volume-synchronized Probability of Informed trading (VPIN). The test data used in this study contains five and a half year?s worth of trading data for about 100 most liquid futures contracts, includes about 3 billion trades, and takes 140GB as text files. By using (1) a more efficient file format for storing the trading records, (2) more effective data structures and algorithms, and (3) parallelizing the computations, we are able to explore 16,000 different ways of computing VPIN in less than 20 hours on a 32-core IBM DataPlex machine. Our test demonstrates that a modest computer is sufficient to monitor a vast number of trading activities in real-time ? an ability that could be valuable to regulators. Our test results also confirm that VPIN is a strong predictor of liquidity-induced volatility. With appropriate parameter choices, the false positive rates are about 7percent averaged over all the futures contracts in the test data set. More specifically, when VPIN values rise above a threshold (CDF > 0.99), the volatility in the subsequent time windows is higher than the average in 93percent of the cases.

  10. Virtual Sea Method For Analyzing Micro-Vibrations Of Spacecrafts

    Science.gov (United States)

    Borello, Gerard; Ozenne, Guillaume; Soula, Laurent; Laduree, Gregory; Maussang, Irwin

    2012-07-01

    For better control of micro-vibration environment into orbit, it is necessary to extend the frequency range of interest to mid and high frequencies, typically up to 5 kHz as they contribute significantly to overall level. Thus, there is a need for improved vibroacoustic technique to predict broadband frequency response of payloads submitted to micro-vibration sources. Due to structural complexity of payloads, classical Statistical Energy Analysis (SEA) method based on analytical description of dynamical subsystems is not very suitable for this analysis. Instead, an alternate energy-based method called Virtual SEA (VSEA) is used here (VSEA was previously validated for separation shock response prediction and implemented in SEAVirt and SEA+ software). VSEA model parameters are similar to SEA but are derived from a FEM model of the payload by inverse method based on Experimental SEA (ESEA) with the advantage of automatically providing the SEA subsystems decomposition insuring weak coupling between VSEA subsystems. To adapt VSEA methodology to micro-vibrations, a VSEA model of a space structure, built by ASTRIUM and used for analyzing micro-vibrations (MICADO), was first proven to be accurate with broadband under- controlled excitations by comparing predictions with series of tests. Then the specific narrow band aspect of micro- vibrations sources has been investigated with adaptation of VSEA method to this specificity. For this, VSEA predictions with actual sources such as wheel and cryo-cooler were performed and compared with tests in steady or unsteady states. VSEA models are delivering accurate results as soon as calculation of injected power from the source in the system is adapted to narrow band signature. VSEA method is presently leveraged to provide not only band- integrated results but also narrow band Power Spectral Density (PSD) estimates as well as local rotations on receiver subsystems.

  11. Trends in nuclear power developments

    International Nuclear Information System (INIS)

    Modern state and prospects of nuclear power development in industrial states are considered. Structure of power consumption, dynamics of nuclear capacity commissioning, the growth of specific capital expenses for reactor construction, orders for NPP production are analyzed. Electric power production costs at NPPs and coal TPPs in Canada, USA, Western Europe and Japan are compared. It is underlined that inspite of certain depressions nuclear power is being developed further on. Increase of electric power consumption for commercial and public purposes and growth of fresh water shortage appear to be the main prerequisites of its further development

  12. Polarized 3He Gas Circulating Technologies for Neutron Analyzers

    Energy Technology Data Exchange (ETDEWEB)

    Watt, David; Hersman, Bill

    2014-12-10

    We describe the development of an integrated system for quasi-continuous operation of a large volume neutron analyzer. The system consists of a non-magnetic diaphragm compressor, a prototype large volume helium polarizer, a surrogate neutron analyzer, a non-depolarizing gas storage reservoir, a non-ferrous valve manifold for handling gas distribution, a custom rubidium-vapor gas return purifier, and wire-wound transfer lines, all of which are immersed in a two-meter external magnetic field. Over the Phase II period we focused on three major tasks required for the successful deployment of these types of systems: 1) design and implementation of gas handling hardware, 2) automation for long-term operation, and 3) improvements in polarizer performance, specifically fabrication of aluminosilicate optical pumping cells. In this report we describe the design, implementation, and testing of the gas handling hardware. We describe improved polarizer performance resulting from improved cell materials and fabrication methods. These improvements yielded valved 8.5 liter cells with relaxation times greater than 12 hours. Pumping this cell with 1500W laser power with 1.25nm linewidth yielded peak polarizations of 60%, measured both inside and outside the polarizer. Fully narrowing this laser to 0.25nm, demonstrated separately on one stack of the four, would have allowed 70% polarization with this cell. We demonstrated the removal of 5 liters of polarized helium from the polarizer with no measured loss of polarization. We circulated the gas through a titanium-clad compressor with polarization loss below 3% per pass. We also prepared for the next phase of development by refining the design of the polarizer so that it can be engineer-certified for pressurized operation. The performance of our system far exceeds comparable efforts elsewhere.

  13. Advanced Power System Analysis Capabilities

    Science.gov (United States)

    1997-01-01

    As a continuing effort to assist in the design and characterization of space power systems, the NASA Lewis Research Center's Power and Propulsion Office developed a powerful computerized analysis tool called System Power Analysis for Capability Evaluation (SPACE). This year, SPACE was used extensively in analyzing detailed operational timelines for the International Space Station (ISS) program. SPACE was developed to analyze the performance of space-based photovoltaic power systems such as that being developed for the ISS. It is a highly integrated tool that combines numerous factors in a single analysis, providing a comprehensive assessment of the power system's capability. Factors particularly critical to the ISS include the orientation of the solar arrays toward the Sun and the shadowing of the arrays by other portions of the station.

  14. Field experience with the mini multi channel analyzer (MMCA)

    International Nuclear Information System (INIS)

    The Mini MCA (MMCA, model MCA-166) is a unique, small size, portable 4K channel multi channel analyzer, multi scaler and timer/counter. It has a low power microprocessor which controls a sophisticated amplifier and fast ADC with constant dead time of 7 microsec. The internal power supply is suitable for a great variety of radiation detectors including germanium detectors (HPGe). It includes preamplifier power and detector high voltage supply. The MMCA has been developed in the Forschungszentrum Rossendorf under the German Support Programme for the Department of Safeguards of the IAEA and for the EURATOM Inspectorate. It is produced by GBS Elektronik in Rossendorf near Dresden. Since it is fully computer controlled, it forms a small size, light weight and versatile measurement platform. Different radiation detectors can be connected, easily configured and used. Its design reduces the weight of the measurement system by about an order of magnitude compared to similar equipment of the previous generation. Both the IAEA and EURATOM have introduced this device into their safeguards instrumentation inventories. The first field uses of the device have covered so far the following applications: U-235 enrichment measurements with NaI and CdZnTe detectors; U-235 measurements using MGAU and HPGe; U/Pu qualitative attribute tests using NaI and CdZnTe detectors; Spent fuel verification using SFAT (Spent Fuel Attribute Tester); Criticality test using a He-3 counter; Active length measurements using a CdZnTe detector; Spectral gamma survey (Iraq Action Team). In this paper the use of the MMCA in some of the above applications in initial inventory verifications is described. This is an inspection activity which requires the use of portable and versatile inspection equipment to cover a wide range of verification methods. The device so far has been used in more then 20 inspections. Its major advantage appeared to be its small size, long battery lifetime and hardware versatility

  15. Power Divider

    OpenAIRE

    Chen, Yu Christine; Dhople, Sairaj

    2015-01-01

    This paper derives analytical closed-form expressions that uncover the contributions of nodal active- and reactive-power injections to the active- and reactive-power flows on transmission lines in an AC electrical network. Paying due homage to current- and voltage-divider laws that are similar in spirit, we baptize these as the power divider laws. Derived from a circuit-theoretic examination of AC power-flow expressions, the constitution of the power divider laws reflects the topology and vol...

  16. Elites, power sources and democracy

    OpenAIRE

    Yetkin, Deniz

    2008-01-01

    This thesis is about elites in general, and the acquisition and maintenance of power in particular. The last concern of the thesis is democracy. For this reason, the classical elite theorists’ and the democratic elite theorists’ perceptions of the elite were critically analyzed. Moreover, power for becoming a part of the elites and power of the elites were discussed. In addition to these discussions, ideas of classical and democratic elite theorists about the possibility of democracy under el...

  17. Nuclear power

    International Nuclear Information System (INIS)

    This chapter of the final report of the Royal Commission on Electric Power Planning in Ontario updates its interim report on nuclear power in Ontario (1978) in the light of the Three Mile Island accident and presents the commission's general conclusions and recommendations relating to nuclear power. The risks of nuclear power, reactor safety with special reference to Three Mile Island and incidents at the Bruce generating station, the environmental effects of uranium mining and milling, waste management, nuclear power economics, uranium supplies, socio-political issues, and the regulation of nuclear power are discussed. Specific recommendations are made concerning the organization and public control of Ontario Hydro, but the commission concluded that nuclear power is acceptable in Ontario as long as satisfactory progress is made in the disposal of uranium mill tailings and spent fuel wastes. (LL)

  18. Power electronic systems Walsh analysis with Matlab

    CERN Document Server

    Deb, Anish

    2014-01-01

    A Totally Different Outlook on Power Electronic System AnalysisPower Electronic Systems: Walsh Analysis with MATLAB® builds a case for Walsh analysis as a powerful tool in the study of power electronic systems. It considers the application of Walsh functions in analyzing power electronic systems, and the advantages offered by Walsh domain analysis of power electronic systems. Solves Power Electronic Systems in an Unconventional WayThis book successfully integrates power electronics as well as systems and control. Incorporating a complete orthonormal function set very much unlike the sine-cosin

  19. Stockholm Power Tech. Power systems

    International Nuclear Information System (INIS)

    The proceedings from this symposium is presented in six volumes: Invited speakers' sessions; Power systems; Power electronics; High-voltage technology; Electrical machines and drives; and Information and control systems. This report covers the power systems volume. Separate abstracts have been prepared for 141 of the 145 papers in this volume

  20. Stockholm Power Tech. Power systems

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The proceedings from this symposium is presented in six volumes: Invited speakers` sessions; Power systems; Power electronics; High-voltage technology; Electrical machines and drives; and Information and control systems. This report covers the power systems volume. Separate abstracts have been prepared for 141 of the 145 papers in this volume

  1. Smile Analyzer: A Software Package for Analyzing the Characteristics of the Speech and Smile

    Directory of Open Access Journals (Sweden)

    Roozbeh Rashed

    2013-01-01

    Full Text Available Taking into account the factors related to lip-tooth relationships in orthodontic diagnosis and treatment planning is of prime importance. Manual quantitative analysis of facial parameters on photographs during smile and speech is a difficult and time-consuming job. Since there is no comprehensive and user-friendly software package, we developed a software program called "Smile Analyzer" in the Department of Orthodontics of Mashhad Faculty of Dentistry for measuring the parameters related to lip-tooth relationships and other facial landmarks on the photographs taken during various facial expressions. The software was designed using visual basic. NET and the ADO. NET was used for developing its Microsoft Access database. The program runs on Microsoft Windows. It is capable of analyzing many parameters or variables in many patients' photographs, although 19 more common variables are previously defined as a default list of variables. When all variables are measured or calculated, a report can be generated and saved in either PDF or MS Excel format. Data are readily transferable to statistical software like SPSS for Windows.  

  2. Development of a test facility for analyzing supercritical fluid blowdown

    Energy Technology Data Exchange (ETDEWEB)

    Roberto, Thiago D.; Alvim, Antonio C.M., E-mail: thiagodbtr@gmail.com [Coordenacao dos Programas de Pos-Graduacao em Engenharia (PEN/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear; Silva, Mario A.B. da, E-mail: mabs500@gmail.com [Universidade Federal de Pernambuco (CTG/UFPE), Recife, PE (Brazil). Departamento de Energia Nuclear; Lapa, Celso M.F., E-mail: lapa@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    The generation IV nuclear reactors under development mostly use supercritical fluids as the working fluid because higher temperatures improve the thermal efficiency. Supercritical fluids are used by modern nuclear power plants to achieve thermal efficiencies of around 45%. With water as the supercritical working fluid, these plants operate at a high temperature and pressure. However, experiments on supercritical water are limited by technical and financial difficulties. These difficulties can be overcome by using model fluids, which have more feasible supercritical conditions and exhibit a lower critical pressure and temperature. Experimental research is normally used to determine the conditions under which model fluids represent supercritical fluids under steady-state conditions. A fluid-to-fluid scaling approach has been proposed to determine model fluids that can represent supercritical fluids in a transient state. This paper presents an application of fractional scale analysis to determine the simulation parameters for a depressurization test facility. Carbon dioxide (CO{sub 2}) and R134a gas were considered as the model fluids because their critical point conditions are more feasible than those of water. The similarities of water (prototype), CO{sub 2} (model) and R134a (model) for depressurization in a pressure vessel were analyzed. (author)

  3. Analyzing and Visualizing Cosmological Simulations with ParaView

    Energy Technology Data Exchange (ETDEWEB)

    Woodring, Jonathan [Los Alamos National Laboratory (LANL); Heitmann, Katrin [ORNL; Ahrens, James P [ORNL; Fasel, Patricia [Los Alamos National Laboratory (LANL); Hsu, Chung-Hsing [ORNL; Habib, Salman [ORNL; Pope, Adrian [Los Alamos National Laboratory (LANL)

    2011-01-01

    The advent of large cosmological sky surveys - ushering in the era of precision cosmology - has been accompanied by ever larger cosmological simulations. The analysis of these simulations, which currently encompass tens of billions of particles and up to a trillion particles in the near future, is often as daunting as carrying out the simulations in the first place. Therefore, the development of very efficient analysis tools combining qualitative and quantitative capabilities is a matter of some urgency. In this paper, we introduce new analysis features implemented within ParaView, a fully parallel, open-source visualization toolkit, to analyze large N-body simulations. A major aspect of ParaView is that it can live and operate on the same machines and utilize the same parallel power as the simulation codes themselves. In addition, data movement is in a serious bottleneck now and will become even more of an issue in the future; an interactive visualization and analysis tool that can handle data in situ is fast becoming essential. The new features in ParaView include particle readers and a very efficient halo finder that identifies friends-of-friends halos and determines common halo properties, including spherical overdensity properties. In combination with many other functionalities already existing within ParaView, such as histogram routines or interfaces to programming languages like Python, this enhanced version enables fast, interactive, and convenient analyses of large cosmological simulations. In addition, development paths are available for future extensions.

  4. Analyzing, Modeling, and Simulation for Human Dynamics in Social Network

    Directory of Open Access Journals (Sweden)

    Yunpeng Xiao

    2012-01-01

    Full Text Available This paper studies the human behavior in the top-one social network system in China (Sina Microblog system. By analyzing real-life data at a large scale, we find that the message releasing interval (intermessage time obeys power law distribution both at individual level and at group level. Statistical analysis also reveals that human behavior in social network is mainly driven by four basic elements: social pressure, social identity, social participation, and social relation between individuals. Empirical results present the four elements' impact on the human behavior and the relation between these elements. To further understand the mechanism of such dynamic phenomena, a hybrid human dynamic model which combines “interest” of individual and “interaction” among people is introduced, incorporating the four elements simultaneously. To provide a solid evaluation, we simulate both two-agent and multiagent interactions with real-life social network topology. We achieve the consistent results between empirical studies and the simulations. The model can provide a good understanding of human dynamics in social network.

  5. Development of a test facility for analyzing supercritical fluid blowdown

    International Nuclear Information System (INIS)

    The generation IV nuclear reactors under development mostly use supercritical fluids as the working fluid because higher temperatures improve the thermal efficiency. Supercritical fluids are used by modern nuclear power plants to achieve thermal efficiencies of around 45%. With water as the supercritical working fluid, these plants operate at a high temperature and pressure. However, experiments on supercritical water are limited by technical and financial difficulties. These difficulties can be overcome by using model fluids, which have more feasible supercritical conditions and exhibit a lower critical pressure and temperature. Experimental research is normally used to determine the conditions under which model fluids represent supercritical fluids under steady-state conditions. A fluid-to-fluid scaling approach has been proposed to determine model fluids that can represent supercritical fluids in a transient state. This paper presents an application of fractional scale analysis to determine the simulation parameters for a depressurization test facility. Carbon dioxide (CO2) and R134a gas were considered as the model fluids because their critical point conditions are more feasible than those of water. The similarities of water (prototype), CO2 (model) and R134a (model) for depressurization in a pressure vessel were analyzed. (author)

  6. Analyzing mitochondrial dynamics in mouse organotypic slice cultures.

    Science.gov (United States)

    Pham, Anh H; Chan, David C

    2014-01-01

    Mitochondria are mobile organelles that dynamically remodel their membranes and actively migrate along cytoskeletal tracks. There is overwhelming evidence that regulators of mitochondrial dynamics are critical for the survival and function of neural tissues. In multiple animal models, ablation of genes regulating mitochondrial shape result in stunted neural development and neurodegeneration. Organotypic cultures serve as ideal in vitro tissue models to further dissect the mechanisms of mitochondrial function in neuronal survival. Slice cultures preserve the three-dimensional cytoarchitecture of neural networks and can survive for prolonged periods in culture. In addition, these cultures allow long-term assessment of genetic or pharmacologic perturbations on neuronal function. Organotypic preparations from murine and rat models have been developed for many regions of the brain. In this chapter, we describe our methods for preparing basal ganglia and cerebellar slice cultures suitable for studying mitochondrial function in Parkinson's disease and cerebellar ataxia, respectively. With such slices, we describe a robust method for live imaging of mitochondrial dynamics. To quantitatively analyze mitochondrial motility, we show how to generate kymographs using the open source image analysis program ImageJ. These techniques provide a powerful platform for assessing mitochondrial activity in neural networks. PMID:25416355

  7. Compact 180 deg magnetic energy analyzer for relativistic electron beams

    International Nuclear Information System (INIS)

    A compact, 180 deg deflection magnetic energy analyzer has been designed and used to measure the energy spectrum of the beam produced by the Tesla Transformer-Pulse forming line type Relativistic Electron Beam (REB) generator being used in the FEL experiments that are currently underway at Institute for Plasma Research. Relativistic electron beams have been used in many applications ranging from free-electron lasers to virtual cathode oscillators and other high power microwave devices. In all these cases, it is required that the electron beam is propagated without considerable loss across a drift region and it is also imperative that accurate energy measurements are required for dependable estimates and analysis regarding the output parameters of the system. In the case of a free-electron laser, the output wavelength of the FEL has a strong dependence on the beam energy and hence it is important to determine as accurately as possible, the energy of the electron beam in order to accurately estimate the FEL radiation frequency

  8. Using biological networks to integrate, visualize and analyze genomics data.

    Science.gov (United States)

    Charitou, Theodosia; Bryan, Kenneth; Lynn, David J

    2016-01-01

    Network biology is a rapidly developing area of biomedical research and reflects the current view that complex phenotypes, such as disease susceptibility, are not the result of single gene mutations that act in isolation but are rather due to the perturbation of a gene's network context. Understanding the topology of these molecular interaction networks and identifying the molecules that play central roles in their structure and regulation is a key to understanding complex systems. The falling cost of next-generation sequencing is now enabling researchers to routinely catalogue the molecular components of these networks at a genome-wide scale and over a large number of different conditions. In this review, we describe how to use publicly available bioinformatics tools to integrate genome-wide 'omics' data into a network of experimentally-supported molecular interactions. In addition, we describe how to visualize and analyze these networks to identify topological features of likely functional relevance, including network hubs, bottlenecks and modules. We show that network biology provides a powerful conceptual approach to integrate and find patterns in genome-wide genomic data but we also discuss the limitations and caveats of these methods, of which researchers adopting these methods must remain aware. PMID:27036106

  9. Test/QA Plan for Verification of Isotopic Carbon Dioxide Analyzers for Carbon Sequestration Monitoring

    Science.gov (United States)

    The purpose of this verification test is to generate performance data on isotopic CO2 analyzers with a particular focus on applications relevant to GCS monitoring applications, specifically for the sequestration of CO2 from a coal-fired power plant. The data generated from this ...

  10. A Method for Analyzing the Coherence of High School Biology Textbooks

    Science.gov (United States)

    Roseman, Jo Ellen; Stern, Luli; Koppal, Mary

    2010-01-01

    Because textbooks have the potential to be powerful catalysts for improving science teaching and learning, having reliable methods for analyzing important textbook features, such as their coherence, is essential. This study reports on the development of a method in which trained reviewers, following a set of guidelines defining the ideas to be…

  11. Tiny Integrated Network Analyzer for Noninvasive Measurements of Electrically Small Antennas

    DEFF Research Database (Denmark)

    Buskgaard, Emil Feldborg; Krøyer, Ben; Tatomirescu, Alexandru; Franek, Ondrej; Pedersen, Gert F.

    2016-01-01

    system. The tiny integrated network analyzer is a stand-alone Arduino-based measurement system that utilizes the transmit signal of the system under test as its reference. It features a power meter with triggering ability, on-board memory, universal serial bus, and easy extendibility with general...

  12. Similarities and differences between conventional power and nuclear power

    International Nuclear Information System (INIS)

    As the implementation of the national guideline of 'proactively promoting nuclear power development', especially after China decided in 2006 to introduce Westinghouse's AP1000 technology, some of the power groups specialized in conventional power generation, have been participating in the preliminary work and construction of nuclear power projects in certain degrees. Meanwhile, such traditional nuclear power corporations as China National Nuclear Corporation (CNNC) and China Guangdong Nuclear Power Corporation (CGNPC) have also employed some employees with conventional power generation experience. How can these employees who have long been engaged in conventional power generation successfully adapt to the new work pattern, ideology, knowledge, thinking mode and proficiency of nuclear power, so that they can fit in with the work requirements of nuclear power and become qualified as soon as possible? By analyzing the technological, managerial and cultural features of nuclear power, as well as some issues to be kept in mind when engaged in nuclear power, this paper intends to make some contribution to the nuclear power development in the specific period. (author)

  13. Power Balance of a Hybrid Power Source in a Power Plant for a Small Propulsion Aircraft

    OpenAIRE

    Bataller Planes, Elena; Lapena Rey, Nieves; Mosquera, Jonay; Ortí, Fortunato; Oliver Ramírez, Jesús Angel; García Suárez, Oscar; Moreno González, Felix Antonio; Portilla Berrueco, Jorge; Torroja Fungairiño, Yago; Vasic, Miroslav; Huerta Oliveres, Santa Concepción; Trocki, M.; Zumel Vaquero, Pablo; Cobos Márquez, José Antonio

    2008-01-01

    This paper analyzes two different architectures for a hybrid power source comprising a PEM (Polymer Electrolyte Membrane) fuel cell and a Li ion battery. The hybrid power source feeds the propulsion motor of an all electrical aircraft, the Boeing Fuel Cell Demonstrator. The architectures are an unregulated and a regulated hybrid power source. The regulation is achieved by means of a controllable series boost converter (SBC) connected in series with the fuel cell. Both architectures have been ...

  14. Power Converters and Power Quality

    CERN Document Server

    Kahle, K

    2015-01-01

    This paper discusses the subject of power quality for power converters. The first part gives an overview of most of the common disturbances and power quality issues in electrical networks for particle accelerators, and explains their consequences for accelerator operation. The propagation of asymmetrical network disturbances into a network is analysed. Quantitative parameters for network disturbances in a typical network are presented, and immunity levels for users’ electrical equipment are proposed. The second part of this paper discusses the technologies and strategies used in particle accelerator networks for power quality improvement . Particular focus is given to networks supplying loads with cycling active and reactive power

  15. Orbital angular momentum complex spectrum analyzer for vortex light based on rotational Doppler Effect

    CERN Document Server

    Zhou, Hailong; Dong, Jianji; Zhang, Pei; Chen, Dongxu; Cai, Xinlun; Li, Fuli; Zhang, Xinliang

    2016-01-01

    The function to measure orbital angular momentum (OAM) distribution of vortex light is essential for OAM applications. Although there are lots of works to measure OAM modes, it is difficult to measure the power distribution of different OAM modes quantitatively and instantaneously, let alone measure the phase distribution among them. In this work, we demonstrate an OAM complex spectrum analyzer, which enables to measure the power and phase distribution of OAM modes simultaneously by employing rotational Doppler Effect. The original OAM mode distribution is mapped to electrical spectrum of beating signals with a photodetector. The power distribution and phase distribution of superimposed OAM beams are successfully retrieved by analyzing the electrical spectrum. We also extend the measurement to other spatial modes, such as linear polarization modes. These results represent a new landmark of spatial mode analysis and show great potentials in optical communication and OAM quantum state tomography.

  16. 40 CFR 86.1321-94 - Hydrocarbon analyzer calibration.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Hydrocarbon analyzer calibration. 86... Procedures § 86.1321-94 Hydrocarbon analyzer calibration. The FID hydrocarbon analyzer shall receive the... into service and at least annually thereafter, the FID hydrocarbon analyzer shall be adjusted...

  17. 40 CFR 92.119 - Hydrocarbon analyzer calibration.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Hydrocarbon analyzer calibration. 92... Hydrocarbon analyzer calibration. The HFID hydrocarbon analyzer shall receive the following initial and... into service and at least annually thereafter, the HFID hydrocarbon analyzer shall be adjusted...

  18. Active Power Controls from Wind Power: Bridging the Gaps

    Energy Technology Data Exchange (ETDEWEB)

    Ela, E.; Gevorgian, V.; Fleming, P.; Zhang, Y. C.; Singh, M.; Muljadi, E.; Scholbrook, A.; Aho, J.; Buckspan, A.; Pao, L.; Singhvi, V.; Tuohy, A.; Pourbeik, P.; Brooks, D.; Bhatt, N.

    2014-01-01

    This paper details a comprehensive study undertaken by the National Renewable Energy Laboratory, Electric Power Research Institute, and the University of Colorado to understand how the contribution of wind power providing active power control (APC) can benefit the total power system economics, increase revenue streams, improve the reliability and security of the power system, and provide superior and efficient response while reducing any structural and loading impacts that may reduce the life of the wind turbine or its components. The study includes power system simulations, control simulations, and actual field tests using turbines at NREL's National Wind Technology Center (NWTC). The study focuses on synthetic inertial control, primary frequency control, and automatic generation control, and analyzes timeframes ranging from milliseconds to minutes to the lifetime of wind turbines, locational scope ranging from components of turbines to large wind plants to entire synchronous interconnections, and additional topics ranging from economics to power system engineering to control design.

  19. Power price and costs

    International Nuclear Information System (INIS)

    A tentative ordering of price and cost concepts in the field of energy economy is presented (sectorial, national and international level). An analysis of the various stages of formation of prices and costs is proposed for four leading energetic chains: coal, gas, petroleum (and petroleum products) and electric power chain, nuclear electric power being analyzed apart. Numerical data are given for the period 1971-1974. Two problems are examined in view of comparing prices and costs: the necessity of discriminating past data from that to be obtained or estimated for the future, and the definition of the functions and their role in the comparison

  20. Low Power WiFi: a study on power consumption for Internet of Things

    OpenAIRE

    Amozarrain Perez, Ugaitz

    2015-01-01

    An analysis of a Low-Power WiFi devices and the feasibility of using such a device for Internet of Things applications, for wireless sensor networks more specifically. The device is analyzed in power consumption and performance.

  1. Modelling of Power Electronic Compensators for the Analysis of Power System Operation

    OpenAIRE

    Robert Kowalak

    2013-01-01

    The article presents selected methods of modelling power electronic compensators in order to analyze their operation in the power systems. Advantages and disadvantages of models have been shown with an indication of their usefulness for modelling specific phenomena.

  2. Reassessing Power

    Institute of Scientific and Technical Information of China (English)

    CHARLES; K.EBINGER; JOHN; P.BANKS

    2011-01-01

    Fukushima accident increases global concern over nuclear safety The accident at the Fukushima Daiichi Nuclear Power Plant in Japan has had an immediate impact on resurgent interest in nuclear power worldwide.Numerous governments have announced plans to re-examine nuclear energy policy and review the safety of their reactors and the adequacy of their regulatory frameworks.

  3. Power Drain

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Rising coal prices mean dwindling profits for China’s power plants. In some cases,they have forced plants to close their doors If electricity prices were not raised together with fuel prices, the country’spower plants could not survive. This isthe common voice of China’s power plants now.

  4. Normative Power

    DEFF Research Database (Denmark)

    researchers, analysts, lecturers and students in their search for an understanding of the EU's normative power in world politics Normative power Europe reconsidered: beyond the crossroadsIan Manners The political economy of ‘normative power' Europe: EU environmental leadership in international biotechnology......Gergana Noutcheva Globalizing European Union environmental policyR. Daniel Kelemen Europe and the new global economic order: internal diversity as liability and asset in managing globalizationOrfeo Fioretos Forthcoming: Normative Power Spotting: An ontological and methodological appraisalElisabeth De Zutter...... understand EU international leadership, small state strategy, interregional relations, international compliance, and the management of globalisation, concluding with an ontological and methodological appraisal of the normative power research programme. This special issue will be of interest to public policy...

  5. Power system

    Science.gov (United States)

    Hickam, Christopher Dale

    2008-03-18

    A power system includes a prime mover, a transmission, and a fluid coupler having a selectively engageable lockup clutch. The fluid coupler may be drivingly connected between the prime mover and the transmission. Additionally, the power system may include a motor/generator drivingly connected to at least one of the prime mover and the transmission. The power-system may also include power-system controls configured to execute a control method. The control method may include selecting one of a plurality of modes of operation of the power system. Additionally, the control method may include controlling the operating state of the lockup clutch dependent upon the mode of operation selected. The control method may also include controlling the operating state of the motor/generator dependent upon the mode of operation selected.

  6. Nuclear power ecology: comparative analysis

    International Nuclear Information System (INIS)

    Ecological effects of different energy sources are compared. Main actions for further nuclear power development - safety increase and waste management, are noted. Reasons of restrained public position to nuclear power and role of social and political factors in it are analyzed. An attempt is undertaken to separate real difficulties of nuclear power from imaginary ones that appear in some mass media. International actions of environment protection are noted. Risk factors at different energy source using are compared. The results of analysis indicate that ecological influence and risk for nuclear power are of minimum

  7. Conflict perspectives in analyzing and understanding organizatioanal behavior

    Directory of Open Access Journals (Sweden)

    Ahmad Shukri bin Mohd Nain

    2004-12-01

    Full Text Available Complex organizations and highly structured organizational networks are part of the obvious features of contemporary life. Organizations, being universal and worldwide phenomenon are becoming increasingly crucial to our life; they often serve as a means for our social, economic and political development. In our contemporary life, organization have developed to be very complex and diverse entities, formed with very high structure of networks. As a result of these development, theories have been developed in an attempt to have a better understanding of organizations and thus creating a more effective and efficient organizations, The rational model has been projected as a gigantic and fabulous instrument and way of thingking towards the contemporary organizations, whereby an organization is perceived and believed to be a stable entity, always integrated, consensus, ordering and well coordinated, only if the reles of the scientific management and bureaucratic model are being fully adopted. Nevertheless, in early 1970s, Western cultures have reached a discontinuity. The decade opened opportunities and led to a societal confusion that we now recognize as signaling the end of an era, the end of a millennial, the ends of the cold war and sovereign states. The changes were massive, they affected the meaning of power. They affected our values. As a result, theories were developed to explains the changes that happened in the recent decades or predict the events of coming decades. However, rationality models were increasingly recognized to be devoid of empirical content. Whilst, order and progress in organization had not happened all the time, cooperation was too fragile and fleeting, purposiveness was too elusive, conflict and coercion were too frequent, disintegration, differences, antagonism and divided loyalties were valid representations of contemporary organizational reality, which was demonstrated by a huge number of institutions in contemporary

  8. Irradiated Microsphere Gamma Analyzer for Examination of Particle Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Paul A. Demkowicz; Various

    2014-06-01

    Fabrication of the first series of fuel compacts for the current US tristructural isotropic (TRISO) coated particle fuel development and qualification effort was completed at Oak Ridge National Laboratory (ORNL) in 2006. In November of 2009, after almost 3 years and 620 effective full power days of irradiation in the Advanced Test Reactor at Idaho National Laboratory (INL), the first Advanced Gas Reactor irradiation test (AGR-1) was concluded. Compacts were irradiated at a calculated timeaveraged, volume-averaged temperature of 955–1136°C to a burnup ranging from 11.2–19.5% fissions per initial metal atom and a total fast fluence of 2.2–4.3·1025 n/m2 [1]. No indication of fission product release from TRISO coating failure was observed during the irradiation test, based on real-time monitoring of gaseous fission products. Post-irradiation examination (PIE) and hightemperature safety testing of the compacts has been in progress at both ORNL and INL since 2010, and have revealed small releases of a limited subset of fission products (such as silver, cesium, and europium). Past experience has shown that some elements can be released from TRISO particles when a defect forms in the SiC layer, even when one or more pyrocarbon layers remain intact and retain the gaseous fission products. Some volatile elements can also be released by diffusion through an intact SiC layer during safety testing if temperatures are high enough and the duration is long enough. In order to understand and quantify the release of certain radioactive fission products, it is sometimes necessary to individually examine each of the more than 4000 coated particles in a given compact. The Advanced Irradiated Microsphere Gamma Analyzer (Advanced- IMGA) was designed to perform this task in a remote hot cell environment. This paper describes the Advanced- IMGA equipment and examination process and gives results for a typical full compact evaluation.

  9. Analyzing and designing object-oriented missile simulations with concurrency

    Science.gov (United States)

    Randorf, Jeffrey Allen

    2000-11-01

    A software object model for the six degree-of-freedom missile modeling domain is presented. As a precursor, a domain analysis of the missile modeling domain was started, based on the Feature-Oriented Domain Analysis (FODA) technique described by the Software Engineering Institute (SEI). It was subsequently determined the FODA methodology is functionally equivalent to the Object Modeling Technique. The analysis used legacy software documentation and code from the ENDOSIM, KDEC, and TFrames 6-DOF modeling tools, including other technical literature. The SEI Object Connection Architecture (OCA) was the template for designing the object model. Three variants of the OCA were considered---a reference structure, a recursive structure, and a reference structure with augmentation for flight vehicle modeling. The reference OCA design option was chosen for maintaining simplicity while not compromising the expressive power of the OMT model. The missile architecture was then analyzed for potential areas of concurrent computing. It was shown how protected objects could be used for data passing between OCA object managers, allowing concurrent access without changing the OCA reference design intent or structure. The implementation language was the 1995 release of Ada. OCA software components were shown how to be expressed as Ada child packages. While acceleration of several low level and other high operations level are possible on proper hardware, there was a 33% degradation of 4th order Runge-Kutta integrator performance of two simultaneous ordinary differential equations using Ada tasking on a single processor machine. The Defense Department's High Level Architecture was introduced and explained in context with the OCA. It was shown the HLA and OCA were not mutually exclusive architectures, but complimentary. HLA was shown as an interoperability solution, with the OCA as an architectural vehicle for software reuse. Further directions for implementing a 6-DOF missile modeling

  10. Nuclear power plant erection

    International Nuclear Information System (INIS)

    The erection of a nuclear power plant covers all the installation operations related to mechanical and electrical equipment in buildings designed for this specific purpose. Some of these operations are described: erection of the nuclear boiler, erection work carried out in the building accomodating the nuclear auxiliary and ancillary equipment and the methods and the organization set up in order to carry out this work satisfactorily are analyzed

  11. Electric power distribution reliability

    CERN Document Server

    Brown, Richard E

    2002-01-01

    Balancing theory, practical knowledge, and real-world applications, this reference consolidates all pertinent topics related to power distribution reliability into one comprehensive volume. Exploring pressing issues in creating and analyzing reliability models, the author highlights the most effective techniques to achieve maximum performance at lowest cost. With over 300 tables, figures, and equations, the book discusses service interruptions caused by equipment malfunction, animals, trees, severe weather, natural disasters, and human error and evaluates strategies to improve reliability and

  12. Distributed Space Solar Power

    Science.gov (United States)

    Fork, Richard L.

    2001-01-01

    The objective was to assess the feasibility of safely collecting solar power at geostationary orbit and delivering it to earth. A strategy which could harness a small fraction of the millions of gigawatts of sunlight passing near earth could adequately supply the power needs of earth and those of space exploration far into the future. Light collected and enhanced both spatially and temporally in space and beamed to earth provides probably the only practical means of safe and efficient delivery of this space solar power to earth. In particular, we analyzed the feasibility of delivering power to sites on earth at a comparable intensity, after conversion to a usable form, to existing power needs. Two major obstacles in the delivery of space solar power to earth are safety and the development of a source suitable for space. We focused our approach on: (1) identifying system requirements and designing a strategy satisfying current eye and skin safety requirements; and (2) identifying a concept for a potential space-based source for producing the enhanced light.

  13. Second order focusing property of 210deg cylindrical energy analyzer

    International Nuclear Information System (INIS)

    It was confirmed experimentally that a 210deg cylindrical energy analyzer with drift spaces has second order focusing. The properties of the analyzer is deeply dependent on the fringing field around the entrance and exit of the cylinders. (author)

  14. Lab-on-a-chip Astrobiology Analyzer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall goal of this program (through Phase III) is to develop an analyzer to measure chemical signatures of life in extraterrestrial settings. The analyzer...

  15. ARC Code TI: Inference Kernel for Open Static Analyzers (IKOS)

    Data.gov (United States)

    National Aeronautics and Space Administration — IKOS is a C++ library designed to facilitate the development of sound static analyzers based on Abstract Interpretation. Specialization of a static analyzer for an...

  16. MESAFace, a graphical interface to analyze the MESA output

    Science.gov (United States)

    Giannotti, M.; Wise, M.; Mohammed, A.

    2013-04-01

    MESA (Modules for Experiments in Stellar Astrophysics) has become very popular among astrophysicists as a powerful and reliable code to simulate stellar evolution. Analyzing the output data thoroughly may, however, present some challenges and be rather time-consuming. Here we describe MESAFace, a graphical and dynamical interface which provides an intuitive, efficient and quick way to analyze the MESA output. Catalogue identifier: AEOQ_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEOQ_v1_0.html Program obtainable from: CPC Program Library, Queen’s University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 19165 No. of bytes in distributed program, including test data, etc.: 6300592 Distribution format: tar.gz Programming language: Mathematica. Computer: Any computer capable of running Mathematica. Operating system: Any capable of running Mathematica. Tested on Linux, Mac, Windows XP, Windows 7. RAM: Recommended 2 Gigabytes or more. Supplementary material: Additional test data files are available. Classification: 1.7, 14. Nature of problem: Find a way to quickly and thoroughly analyze the output of a MESA run, including all the profiles, and have an efficient method to produce graphical representations of the data. Solution method: We created two scripts (to be run consecutively). The first one downloads all the data from a MESA run and organizes the profiles in order of age. All the files are saved as tables or arrays of tables which can then be accessed very quickly by Mathematica. The second script uses the Manipulate function to create a graphical interface which allows the user to choose what to plot from a set of menus and buttons. The information shown is updated in real time. The user can access very quickly all the data from the run under examination and visualize it with plots and tables. Unusual features: Moving the

  17. On Some Improvements of Ion Microprobe Mass Analyzer

    Directory of Open Access Journals (Sweden)

    O.S. Kuzema

    2013-10-01

    Full Text Available It has been considered the ion-optical properties and characteristics of ion microprobe analyzer in which the primary ion beam mass separation is realized by the magnetic prism, and the beam spherical capacitor is used in the secondary ion analyzing system as energy analyzer which form parallel ion beam at the mass analyzer inlet. It has allowed to improve the instrument parameters and to scale down its overall dimension.

  18. Nuclear power

    International Nuclear Information System (INIS)

    The committee concludes that the nature of the proliferation problem is such that even stopping nuclear power completely could not stop proliferation completely. Countries can acquire nuclear weapons by means independent of commercial nuclear power. It is reasonable to suppose if a country is strongly motivated to acquire nuclear weapons, it will have them by 2010, or soon thereafter, no matter how nuclear power is managed in the meantime. Unilateral and international diplomatic measures to reduce the motivations that lead to proliferation should be high on the foreign policy agenda of the United States. A mimimum antiproliferation prescription for the management of nuclear power is to try to raise the political barriers against proliferation through misuse of nuclear power by strengthening the Non-Proliferation Treaty, and to seek to raise the technological barriers by placing fuel-cycle operations involving weapons-usable material under international control. Any such measures should be considered tactics to slow the spread of nuclear weapons and thus earn time for the exercise of statesmanship. The committee concludes the following about technical factors that should be considered in formulating nuclear policy: (1) rate of growth of electricity use is a primary factor; (2) growth of conventional nuclear power will be limited by producibility of domestic uranium sources; (3) greater contribution of nuclear power beyond 400 GWe past the year 2000 can only be supported by advanced reactor systems; and (4) several different breeder reactors could serve in principle as candidates for an indefinitely sustainable source of energy

  19. 21 CFR 862.2500 - Enzyme analyzer for clinical use.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Enzyme analyzer for clinical use. 862.2500 Section... Instruments § 862.2500 Enzyme analyzer for clinical use. (a) Identification. An enzyme analyzer for clinical use is a device intended to measure enzymes in plasma or serum by nonkinetic or kinetic measurement...

  20. 40 CFR 89.320 - Carbon monoxide analyzer calibration.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Carbon monoxide analyzer calibration... Test Equipment Provisions § 89.320 Carbon monoxide analyzer calibration. (a) Calibrate the NDIR carbon... introduction into service and annually thereafter, the NDIR carbon monoxide analyzer shall be checked...

  1. 40 CFR 86.1325-94 - Methane analyzer calibration.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Methane analyzer calibration. 86.1325... Procedures § 86.1325-94 Methane analyzer calibration. Prior to introduction into service and monthly thereafter, the methane analyzer shall be calibrated: (a) Follow the manufacturer's instructions...

  2. 40 CFR 86.125-94 - Methane analyzer calibration.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Methane analyzer calibration. 86.125... Complete Heavy-Duty Vehicles; Test Procedures § 86.125-94 Methane analyzer calibration. Prior to introduction into service and monthly thereafter, the methane analyzer shall be calibrated: (a) Follow...

  3. 40 CFR 86.331-79 - Hydrocarbon analyzer calibration.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Hydrocarbon analyzer calibration. 86....331-79 Hydrocarbon analyzer calibration. The following steps are followed in sequence to calibrate the hydrocarbon analyzer. It is suggested, but not required, that efforts be made to minimize relative...

  4. 21 CFR 868.1720 - Oxygen gas analyzer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Oxygen gas analyzer. 868.1720 Section 868.1720...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Diagnostic Devices § 868.1720 Oxygen gas analyzer. (a) Identification. An oxygen gas analyzer is a device intended to measure the concentration of oxygen in...

  5. 21 CFR 868.1640 - Helium gas analyzer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Helium gas analyzer. 868.1640 Section 868.1640...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Diagnostic Devices § 868.1640 Helium gas analyzer. (a) Identification. A helium gas analyzer is a device intended to measure the concentration of helium in a...

  6. 21 CFR 868.1075 - Argon gas analyzer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Argon gas analyzer. 868.1075 Section 868.1075 Food... DEVICES ANESTHESIOLOGY DEVICES Diagnostic Devices § 868.1075 Argon gas analyzer. (a) Identification. An argon gas analyzer is a device intended to measure the concentration of argon in a gas mixture to aid...

  7. 40 CFR 86.327-79 - Quench checks; NOX analyzer.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Quench checks; NOX analyzer. 86.327-79... Quench checks; NOX analyzer. (a) Perform the reaction chamber quench check for each model of high vacuum... capillary, and if used, dilution capillary. (c) Quench check as follows: (1) Calibrate the NOX analyzer...

  8. Risk of loss power for ATWT in Daya Bay and Ling'ao nuclear power stations

    International Nuclear Information System (INIS)

    In order to analyze the differences between the Anticipated Transient Without Reactor Trip (ATWT) and other reactor protection methods, this paper analyzes in detail the realizing means of ATWT and the effect of lost of power supply on the units based on Daya Bay and Ling'ao Nuclear Power Stations by system wiring diagram. Based on the comprehensive analysis,this paper proposes the sequence for powering when recovering the power source after ATWT power supply (LCC/LNE) loss for Daya Bay and Ling'ao Nuclear Power Stations. (authors)

  9. Nuclear power

    International Nuclear Information System (INIS)

    This chapter discussed the following topics related to the nuclear power: nuclear reactions, nuclear reactors and its components - reactor fuel, fuel assembly, moderator, control system, coolants. The topics titled nuclear fuel cycle following subtopics are covered: , mining and milling, tailings, enrichment, fuel fabrication, reactor operations, radioactive waste and fuel reprocessing. Special topic on types of nuclear reactor highlighted the reactors for research, training, production, material testing and quite detail on reactors for electricity generation. Other related topics are also discussed: sustainability of nuclear power, renewable nuclear fuel, human capital, environmental friendly, emission free, impacts on global warming and air pollution, conservation and preservation, and future prospect of nuclear power

  10. Power politics

    International Nuclear Information System (INIS)

    This article expresses the view that nuclear power is the only logical alternative to dwindling oil supplies, and that blame for failure to implement the nuclear power programme can be placed on the environmentalists, the media and political leaders who have been frightened by anti-nuclear demonstrations and anticipated media reaction to their decisions. President Carter and others have looked upon nuclear power as a last resort, but it is shown here to be more abundant, cheaper, cleaner, and safer than all other currently available sources of energy. (U.K.)

  11. NSTX Electrical Power Systems

    International Nuclear Information System (INIS)

    The National Spherical Torus Experiment (NSTX) has been designed and installed in the existing facilities at Princeton Plasma Physic Laboratory (PPPL). Most of the hardware, plant facilities, auxiliary sub-systems, and power systems originally used for the Tokamak Fusion Test Reactor (TFTR) have been used with suitable modifications to reflect NSTX needs. The design of the NSTX electrical power system was tailored to suit the available infrastructure and electrical equipment on site. Components were analyzed to verify their suitability for use in NSTX. The total number of circuits and the location of the NSTX device drove the major changes in the Power system hardware. The NSTX has eleven (11) circuits to be fed as compared to the basic three power loops for TFTR. This required changes in cabling to insure that each cable tray system has the positive and negative leg of cables in the same tray. Also additional power cabling had to be installed to the new location. The hardware had to b e modified to address the need for eleven power loops. Power converters had to be reconnected and controlled in anti-parallel mode for the Ohmic heating and two of the Poloidal Field circuits. The circuit for the Coaxial Helicity Injection (CHI) System had to be carefully developed to meet this special application. Additional Protection devices were designed and installed for the magnet coils and the CHI. The thrust was to making the changes in the most cost-effective manner without compromising technical requirements. This paper describes the changes and addition to the Electrical Power System components for the NSTX magnet systems

  12. Analyze the test methods for intergranular corrosion-resistance of nickel-based alloys 690

    International Nuclear Information System (INIS)

    The corrosion resistance effective of steam generator heat tubing in PWR nuclear power build highly demanding and direct impact on the reliability of the nuclear power unit to the technical performance and safety. Nickel-based Alloy 690 is the best material for nuclear SG heat tubing. Heat of the damage is caused by various types of corrosion, mainly is intergranular corrosion and stress corrosion cracking. Tests to verify the stability of heat transfer performance and application reliability. Analyze the chemical and electrochemical immersion (EPR) corrosion methods to provide the basic theory for experimental verification of the stability and engineering applications reliability of heat transfer. (authors)

  13. Analyzing Time-Frequency Relationship between Oil Price and Exchange Rate in Pakistan through Wavelets

    OpenAIRE

    Muhammad SHAHBAZ; Tiwari, Aviral Kumar; Tahir, Mohammad Iqbal

    2013-01-01

    This study analyzes the time-frequency relationship between oil price and exchange rate for Pakistan by using measures of continuous wavelet such as wavelet power, cross-wavelet power, and cross-wavelet coherency. The results of cross-wavelet analysis indicate that covariance between oil price and exchange rate are unable to give clear-cut results but both variables have been in phase and out phase (i.e. they are anti-cyclical and cyclical in nature) in some or other durations. However, resul...

  14. A Comparative Study of Power Consumption Models for CPA Attack

    OpenAIRE

    Hassen Mestiri; Noura Benhadjyoussef; Mohsen Machhout; Rached Tourki

    2013-01-01

    Power analysis attacks are types of side channel attacks that are based on analyzing the power consumption of the cryptographic devices. Correlation power analysis is a powerful and efficient cryptanalytic technique. It exploits the linear relation between the predicted power consumption and the real power consumption of cryptographic devices in order to recover the correct key. The predicted power consumption is determined by using the appropriate consumption model. Until now, only a few mod...

  15. Nuclear power

    International Nuclear Information System (INIS)

    Nuclear power has been seen as an answer to the energy problems of the Third World and Third World markets have been seen as an answer to the problems of the nuclear power industry. For some years during the 1970s both views seemed tenable. This paper examines the progress and setbacks of nuclear power in developing countries. In concentrates mainly on the four countries with real nuclear power commitments (as opposed to all-but-abandoned ambitions) - South Korea and Taiwan, where the interest has been mainly in obtaining cheaper and reliable electricity supplies, and Argentina and India, where the main interest has been in developing indigenous nuclear technological capabilities. A number of possibilities are examined which could influence future nuclear ordering, including smaller reactors to suit Third World electricity grids and a possible way round the constraint of large external debts. (author)

  16. Power Preservation

    DEFF Research Database (Denmark)

    Galster, Kjeld

    Power Preservation (Abstract) In the 17th century, just as today, coalitions needed ‘lead nations’. This was assumed to be a power with great military and economic potentials, and Denmark endeavoured to act as such a leader in the Thirty Years War from 1626 to 28. The results were not encouraging...... stage gradually declined. Thus, Denmark of the 17th century is not to be counted amongst the great powers, but since Christian V’s accession to the throne in 1670 Denmark-Norway has developed into one of Europe’s most highly militarised states. Apart from a permanently combat ready navy, the country......-Scottish double monarchy, it is fair to assume that his political ambitions are of a far reaching nature. King Christian wants revenge on Sweden and he wishes to preserve the military and naval power generated during the latest war with that country. However, this is certainly not to be achieved cheaply. To...

  17. Nuclear power

    OpenAIRE

    Waller, David; McDonald, Alan; Greenwald, Judith; Mobbs, Paul

    2005-01-01

    David Waller and Alan McDonald ask whether a nuclear renaissance can be predicted; Judith M. Greenwald discusses keeping the nuclear power option open; Paul Mobbs considers the availability of uranium and the future of nuclear energy.

  18. Introduction to electrical power and power electronics

    CERN Document Server

    Patel, Mukund R

    2012-01-01

    Power Generation, Distribution, and Utilization AC Power Fundamentals Common Aspects of Power Equipments AC Generator AC and DC Motors Transformer Power Cable Power Distribution Fault Current Analysis System ProtectionEconomic Use of PowerElectrochemical BatteryPower Electronics and Motor Drives Power Electronics Devices DC-DC Converters AC-DC-AC Converters Variable-Frequency Drives Quality of Power Power Converter CoolingAppendixIndex

  19. Power coupling

    OpenAIRE

    D. AlesiniLNF, INFN, Frascati

    2015-01-01

    Power coupling is the subject of a huge amount of literature and material since for each particular RF structure it is necessary to design a coupler that satisfies some requirements, and several approaches are in principle possible. The choice of one coupler with respect to another depends on the particular RF design expertise. Nevertheless some 'design criteria' can be adopted and the scope of this paper is to give an overview of the basic concepts in power coupler design and techniques. We ...

  20. POWER PREPARATION

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The days in January were dark days for China.Not only metaphori- cally but literally.Snowstorms wreaked havoc in the south,snuffing out power in 169 counties nationwide due to the failure of 36,740 electricity transmission lines.This paralyzed traffic and suspended water and gas supplies. The reason for the chaos is being blamed on the safety standards of power

  1. MISSE-7 MESA Miniaturized Electrostatic Analyzer - Ion Spectra Analysis Preliminary Results

    Science.gov (United States)

    Enloe, C. L.; Balthazor, R. L.; McHarg, M. G.; Clark, A. L.; Waite, D.; Wallerstein, A. J.; Wilson, K. A.

    2011-12-01

    The 7th Materials on the International Space Station Experiment (MISSE-7) was launched in November 2009 and retrieved on STS-134 in April 2011. One of the onboard experiments, the Miniaturized Electrostatic Analyzer (MESA), is a small low-cost low-size/weight/power ion and electron spectrometer that was pointed into ram during the majority of the time onboard. Over 800 Mb of data has been obtained by taking spectra every three minutes on-orbit. The data has been analyzed with a novel "parameterizing the parameters" method suitable for on-orbit data analysis using low-cost microcontrollers. Preliminary results are shown.

  2. Validation of the Engineering Plant Analyzer methodology with Peach Bottom 2 stability tests

    International Nuclear Information System (INIS)

    The Engineering Plant Analyzer (EPA) had been developed in 1984 at Brookhaven National Laboratory to simulate plant transients in boiling water reactors (BWR). Recently, the EPA with its High-Speed Interactive Plant Analyzer code for BWRs ( ppercase HIPA-BWR ) simulated for the first time oscillatory transients with large, non-linear power and flow amplitudes; transients which are centered around the March 9, 1988 instability at the LaSalle-2 BWR power plant.The EPA's capability to simulate oscillatory transients has been demonstrated first by comparing simulation results with LaSalle-2 plant data (Wulff et al., NUREG/CR-5816, BNL-NUREG-52312, Brookhaven National Laboratory, 1992). This paper presents an EPA assessment on the basis of the Peach Bottom 2 instability tests (Carmichael and Niemi, EPRI NP-564, Electric Power Research Institute, Palo Alto, CA, 1978). This assessment of the EPA appears to constitute the first validation of a time-domain reactor systems code on the basis of frequency-domain criteria, namely power spectral density, gain and phase shift of the pressure-to-power transfer function.The reactor system pressure was disturbed in the Peach Bottom 2 power plant tests, and in their EPA simulation, by a pseudo-random, binary sequence signal. The data comparison revealed that the EPA predicted for Peach Bottom tests PT1, PT2, and PT4 the gain of the power-to-pressure transfer function with the biases and standard deviations of (-10±28)%, (-1±40)% and (+28±52)%, respectively. The respective frequencies at the peak gains were predicted with the errors of +6%, +3%, and -28%. The differences between the predicted and the measured phase shift increased with increasing frequency, but stayed within the margin of experimental uncertainty. ((orig.))

  3. Study on Capability of Power Transmission from West to East in China Southern Power Grid

    Institute of Scientific and Technical Information of China (English)

    Li Wei; Tong Mingdong; Zhang Lin; Xu Dongjie; Lin Feng; Li Xin; Zuo Zhengmin

    2007-01-01

    @@ The uneven distribution of economic development and energy resources in the Southern Power Grid, yet with stronger complementary superiority has determined the necessity to actively push forward power transmission from west to east in the Southern Power Grid and realize optimal disposition in even greater scope. To further promote transmission capability and operational security from west to east, measures including power sources disposition, unit starting schemes, power grid configuration, DC modulation and application of new transmission technologies are analyzed in this paper.

  4. Wind power

    International Nuclear Information System (INIS)

    This book is a translation of the edition published in the USA under the title of ''wind power: renewable energy for home, farm and business''. In the wake of mass blackouts and energy crises, wind power remains a largely untapped resource of renewable energy. It is a booming worldwide industry whose technology, under the collective wing of aficionados like author Paul Gipe, is coming of age. Wind Power guides us through the emergent, sometimes daunting discourse on wind technology, giving frank explanations of how to use wind technology wisely and sound advice on how to avoid common mistakes. Since the mid-1970's, Paul Gipe has played a part in nearly every aspect of wind energy development from installing small turbines to promoting wind energy worldwide. As an American proponent of renewable energy, Gipe has earned the acclaim and respect of European energy specialists for years, but his arguments have often fallen on deaf ears at home. Today, the topic of wind power is cropping up everywhere from the beaches of Cape Cod to the Oregon-Washington border, and one wind turbine is capable of producing enough electricity per year to run 200 average American households. Now, Paul Gipe is back to shed light on this increasingly important energy source with a revised edition of Wind Power. Over the course of his career, Paul Gipe has been a proponent, participant, observer, and critic of the wind industry. His experience with wind has given rise to two previous books on the subject, Wind Energy Basics and Wind Power for Home and Business, which have sold over 50,000 copies. Wind Power for Home and Business has become a staple for both homeowners and professionals interested in the subject, and now, with energy prices soaring, interest in wind power is hitting an all-time high. With chapters on output and economics, Wind Power discloses how much you can expect from each method of wind technology, both in terms of energy and financial savings. The book updated models

  5. The limited power of voting to limit power

    OpenAIRE

    Hong Geng; Arne Robert Weiss; Irenaeus Wolff

    2010-01-01

    In this paper, we experimentally approach the question of which aspects of a voting procedure are able to restrict elected candidates’ willingness to use their power in an opportunistic way. For this purpose, we rule out re-election concerns and analyze whether the presence of a vote by itself matters for the exercise of power. We compare two kinds of electoral campaigns: self-descriptions of personality and promises regarding prospective in-office behavior. We find that social approval as co...

  6. Development of a graphite polarization analyzer for resonant inelastic x-ray scattering.

    Science.gov (United States)

    Gao, Xuan; Burns, Clement; Casa, Diego; Upton, Mary; Gog, Thomas; Kim, Jungho; Li, Chengyang

    2011-11-01

    Resonant inelastic x-ray scattering (RIXS) is a powerful technique for studying electronic excitations in correlated electron systems. Current RIXS spectrometers measure the changes in energy and momentum of the photons scattered by the sample. A powerful extension of the RIXS technique is the measurement of the polarization state of the scattered photons which contains information about the symmetry of the excitations. This long-desired addition has been elusive because of significant technical challenges. This paper reports the development of a new diffraction-based polarization analyzer which discriminates between linear polarization components of the scattered photons. The double concave surface of the polarization analyzer was designed as a good compromise between energy resolution and throughput. Such a device was fabricated using highly oriented pyrolytic graphite for measurements at the Cu K-edge incident energy. Preliminary measurements on a CuGeO(3) sample are presented. PMID:22128967

  7. Modeling and development of software of plant analyzer for pressurized water reactor plants

    International Nuclear Information System (INIS)

    The Nuclear Power Plant Analyzer (NPA), a personal computer based faster running simulator for PWR, is developed for transient analysis, personnel training, and computer-aid diagnosis. The NPA can be divided into two categories: plant module and man-machine interaction module. The plant module-TAPWR, consists of models for core kinetics, fuel transient conduction, reactor coolant system, pressurizer, and U-tube steam generator. Each of the models is optimized to obtain the capability of faster than real-time simulation. To check the sensitivity of models, TAPWR has been benchmarked against RELAP5/MOD2 code for a reactivity insertion accident. The NPA has a convenient, interactive and user friendly graphics interface. Simulation results can be displayed dynamically on a color graphics terminal by the interaction module. Using NPA, a LOFW accident for DAYA Bay Nuclear Power plant is analyzed

  8. France without nuclear power

    International Nuclear Information System (INIS)

    As coal production declined and France found herself in a condition of energy dependency, the country decided to turn to nuclear power and a major construction program was undertaken in 1970. The consequences of this step are examined in this article, by imagining where France would be without its nuclear power. At the end of the sixties, fuel-oil incontestably offered the cheapest way of producing electricity; but the first petroleum crisis was to upset the order of economic performance, and coal then became the more attractive fuel. The first part of this article therefore presents coal as an alternative to nuclear power, describing the coal scenario first and then comparing the relative costs of nuclear and coal investment strategies and operating costs (the item that differs most is the price of the fuel). The second part of the article analyzes the consequences this would have on the electrical power market, from the supply and demand point of view, and in terms of prices. The third part of the article discusses the macro-economic consequences of such a step: the drop in the level of energy dependency, increased costs and the disappearance of electricity exports. The article ends with an analysis of the environmental consequences, which are of greater and greater concern today. The advantage here falls very much in favor of nuclear power, if we judge by the lesser emissions of sulfur dioxide, nitrogen oxides and especially carbon dioxide. 22 refs.; 13 figs.; 10 tabs

  9. Analyzing RCD30 Oblique Performance in a Production Environment

    Science.gov (United States)

    Soler, M. E.; Kornus, W.; Magariños, A.; Pla, M.

    2016-06-01

    In 2014 the Institut Cartogràfic i Geològic de Catalunya (ICGC) decided to incorporate digital oblique imagery in its portfolio in response to the growing demand for this product. The reason can be attributed to its useful applications in a wide variety of fields and, most recently, to an increasing interest in 3d modeling. The selection phase for a digital oblique camera led to the purchase of the Leica RCD30 Oblique system, an 80MPixel multispectral medium-format camera which consists of one Nadir camera and four oblique viewing cameras acquiring images at an off-Nadir angle of 35º. The system also has a multi-directional motion compensation on-board system to deliver the highest image quality. The emergence of airborne oblique cameras has run in parallel to the inclusion of computer vision algorithms into the traditional photogrammetric workflows. Such algorithms rely on having multiple views of the same area of interest and take advantage of the image redundancy for automatic feature extraction. The multiview capability is highly fostered by the use of oblique systems which capture simultaneously different points of view for each camera shot. Different companies and NMAs have started pilot projects to assess the capabilities of the 3D mesh that can be obtained using correlation techniques. Beyond a software prototyping phase, and taking into account the currently immature state of several components of the oblique imagery workflow, the ICGC has focused on deploying a real production environment with special interest on matching the performance and quality of the existing production lines based on classical Nadir images. This paper introduces different test scenarios and layouts to analyze the impact of different variables on the geometric and radiometric performance. Different variables such as flight altitude, side and forward overlap and ground control point measurements and location have been considered for the evaluation of aerial triangulation and

  10. On energy efficient power allocation for power-constrained systems

    KAUST Repository

    Sboui, Lokman

    2014-09-01

    Recently, the energy efficiency (EE) has become an important factor when designing new wireless communication systems. Due to economic and environmental challenges, new trends and efforts are oriented toward “green” communication especially for energy-constrained applications such as wireless sensors network and cognitive radio. To this end, we analyze the power allocation scheme that maximizes the EE defined as rate over the total power including circuit power. We derive an explicit expression of the optimal power with instantaneous channel gain based on EE criterion. We show that the relation between the EE and the spectral efficiency (SE) when the optimal power is adopted is strictly increasing in contrast with the SE-EE trade-off discussed in the literature. We also solve a non-convex problem and compute explicitly the optimal power for ergodic EE under either a peak or an average power constraint. When the instantaneous channel is not available, we provide the optimal power equation and compute simple sub-optimal power. In the numerical results, we show that the sup-optimal solution is very close to the optimal solution. In addition, we show that the absence of the channel state information (CSI) only affects the EE and the SE performances at high power regime compared to the full CSI case.

  11. Analyzing and realizing of database function of fast reactor refueling supervision system

    International Nuclear Information System (INIS)

    Using computers to inspect the nuclear reactor fuel-changed system is helpful for the improvement of the security and reliability of the refueling operation. Nuclear reactor refueling supervision system is developed with the configuration software. Because the system is very complex and a great deal of data should be recorded, it requires a powerful database to suport. This paper analyzes the dat ato be recorded and introduces the solution for real-time recording. (authors)

  12. Analyzing Sustainable Competitive Advantage: Strategically Managing Resource Allocations to Achieve Operational Competitiveness

    OpenAIRE

    Abdul Malek Nurul Aida; Shahzad Khuram; Takala Josu; Bojnec Stefan; Papler Drago; Liu Yang

    2015-01-01

    In today’s dynamic business environment, a key challenge for all companies is to make adaptive adjustments to their manufacturing strategy. This study demonstrates the competitive priorities of manufacturing strategy in hydro-power case company to evaluate the level of sustainable competitive advantage and also to further analyze how business strategies are aligned with manufacturing strategies. This research is based on new holistic analytical evaluation of manufacturing strategy index, sens...

  13. Application of Queuing Theory in Analyzing the Use of Production Capacity

    OpenAIRE

    Muhammad Marsudi

    2010-01-01

    Queuing theory is a major topic of applied mathematics that deals with phenomenon of waiting and arises from the use of powerful mathematical analysis to describe production processes. This study examines the use of production capacity of facilities in Fujitsu Components (M) Sdn. Bhd. based on queuing theory. The aim of this study is to achieve an appropriate queuing analytical model and determine its performance measures by analyzing the capacity requirements and estimating manufacturing cyc...

  14. Is Distant Pollution Contaminating Local Air? Analyzing the Origins of Atmospheric Aerosols

    OpenAIRE

    David Geng

    2012-01-01

    Understanding the origin of aerosols in the atmosphere is important because of visual pollution, climate impacts, and deleterious health effects due to the inhalation of fine particles. This research analyzed aerosols characterized by their chloride, sulfate, and nitrate content as a function of size over a 3-month period. Due to wind patterns over coal-burning power plants, a higher concentration of local sulfate pollution was expected. Aerosols were harvested on the Purdue University campus...

  15. Emergency Linkage Mode of Power Enterprise

    OpenAIRE

    Feng Jie; Yu Zhen; Liu Chao

    2016-01-01

    Power emergency disposal needs take full advantage of the power enterprise within the external emergency power and resources. Based on analyzing and summarizing the relevant experience of domestic and foreign emergency linkage, this paper draws the Emergency Linkage subjects, Emergency Linkage contents, Emergency Linkage level, which are three key elements if power enterprise Emergency Linkage. Emergency Linkage subjects are divided into the two types of inner subjects and the external body; ...

  16. Analyzer of energy spectra of a magnetized relativistic electron beam

    International Nuclear Information System (INIS)

    Analyzer of magnetized REB instant energy spectrum is described. The analyzer operation principle is based on the application of a sharp change of the direction of force lines of a magnetic field which is non-adiabatic for the beam electrons. The analyzer design is described, the main factors effecting the energy resolution are considered. The analyzer serviceability is examined in the course of experiments on plasma heating using a heavy-current microsecond REB at the GOL-3 device. The analyzer energy resolution which does not exceed 10% at 0.8 MeV energy and 20% at 0.3 MeV is determined. Beam energy spectra are obtained in one of the regimes of beam interaction with plasma. The efficiency of beam interaction with plasma determined using the analyzer achieves 30%. 10 refs.; 7 figs

  17. Radiofrequency mass analyzer. Theory, design, technology and utilization

    International Nuclear Information System (INIS)

    In this work the results of research and design of the sensor-analyzer part of a mass spectrometer is presented. It is destined for use as portable gas analyzer for control and technological process supervision, in the environment control, etc. Starting from data and physical principles a generalized mathematical model of the radiofrequency mass analyzer, corresponding to the shape and the amplitude of the potential of high frequency modulation is analyzed. On this basis the peculiarities of the non-linear regime of some RF mass analyzer of optimal and simple scheme of calculation. A number of technological, execution and assembling issues of the RF analysers under production conditions are analyzed. Within the large range of uses of these devices the vacuum technique, thin layer technology, atomic and ionic composition studies of earth and other planet atmospheres, the detection, identification and exhaling gas analyses are mentioned

  18. Nuclear power

    International Nuclear Information System (INIS)

    After three decades of commercial development, nuclear power has failed to fulfil its promise. Why, and what does that failure imply for the future of energy policy? One reason for nuclear power's slow growth is that rich countries have repeatedly found they needed less electricity than they had forecast. Part of the problem is, as it always has been, public unease. Worries about safety affect costs. They make it harder and more time-consuming to find sites for new plants or for storing waste. Complex safety devices mean complex plants, which are more expensive to build (and to relicense when they grow old). The true cost of nuclear power is hard to calculate. However nuclear power now seems to be less economically favourable when compared with its main rival, coal. The only hope for nuclear power is that, apart from hydropower, it is the only commercial alternative to fossil fuels. Concerns over carbon dioxide emissions may tip the balance in nuclear's favour. (Author)

  19. Digital signal processing in the radio science stability analyzer

    Science.gov (United States)

    Greenhall, C. A.

    1995-01-01

    The Telecommunications Division has built a stability analyzer for testing Deep Space Network installations during flight radio science experiments. The low-frequency part of the analyzer operates by digitizing wave signals with bandwidths between 80 Hz and 45 kHz. Processed outputs include spectra of signal, phase, amplitude, and differential phase; time series of the same quantities; and Allan deviation of phase and differential phase. This article documents the digital signal-processing methods programmed into the analyzer.

  20. A case for static analyzers in the cloud

    OpenAIRE

    Barnett, Michael; Bouaziz, Mehdi; Logozzo, Francesco; Fähndrich, Manuel

    2013-01-01

    We describe our ongoing effort of moving a desktop static analyzer, Clousot, into a cloud-based one, Cloudot. A cloud-based static analyzer runs as a service. Clients issue analysis requests through the local network or over the internet. The analysis takes advantage of the large computation resources offered by the cloud: the underlying infrastructure ensures scaling and virtually unlimited storage. Cloud-based analyzers may relax performance-precision trade-offs usually associated with desk...